Surface Passivation Mechanism of Atomic Layer Deposited Al2O3 Films on c-Si Studied by Optical Second-Harmonic Generation

NARCIS (Netherlands)

Gielis, J.J.H.; Verlaan, V.; Dingemans, G.; Sanden, van de M.C.M.; Kessels, W.M.M.; Terlinden, N.M.

2009-01-01

Recently, it was shown that Al2O3 thin films synthesized by (plasmaassisted) atomic layer deposition (ALD) provide excellent surface passivation of n, p and p+ type c-Si as highly relevant for c-Si photovoltaics. It was found that a large negative fixed charge density (up to 1013 cm-2) in the Al2O3

Limiting efficiency of generalized realistic c-Si solar cells coupled to ideal up-converters

Science.gov (United States)

Johnson, Craig M.; Conibeer, Gavin J.

2012-11-01

The detailed balance model of photovoltaic up-conversion is revised for the specific case of a c-Si solar cell under the AM1.5G solar spectrum. The limiting efficiency of an ideal solar cell with a band gap of 1.117 eV may be increased from approximately 33% to 40% with ideal up-conversion. However, real solar cells do not demonstrate the step-function absorption characteristic assumed in the standard detailed balance model. Here, we use tabulated Si refractive index data to develop a generalized model of a realistic conventional c-Si solar cell. The model incorporates optical design and material parameters such as free carrier absorption that have a non-trivial impact on the operation of the up-conversion layer. While these modifications are shown to decrease the absolute limiting efficiency, the benefit of up-conversion is shown to be relatively greater.

Detection of Potential Induced Degradation in c-Si PV Panels Using Electrical Impedance Spectroscopy

DEFF Research Database (Denmark)

Oprea, Matei-lon; Spataru, Sergiu; Sera, Dezso

2016-01-01

This work, for the first time, investigates an Impedance Spectroscopy (IS) based method for detecting potential-induced degradation (PID) in crystalline silicon photovoltaic (c-Si PV) panels. The method has been experimentally tested on a set of panels that were confirmed to be affected by PID...

Variation of carrier concentration and interface trap density in 8MeV electron irradiated c-Si solar cells

Energy Technology Data Exchange (ETDEWEB)

Bhat, Sathyanarayana, E-mail: asharao76@gmail.com; Rao, Asha, E-mail: asharao76@gmail.com [Department of Physics, Mangalore Institute of Technology and Engineering, Moodabidri, Mangalore-574225 (India); Krishnan, Sheeja [Department of Physics, Sri Devi Institute of Technology, Kenjar, Mangalore-574142 (India); Sanjeev, Ganesh [Microtron Centre, Department of Physics, Mangalore University, Mangalagangothri-574199 (India); Suresh, E. P. [Solar Panel Division, ISRO Satellite Centre, Bangalore-560017 (India)

2014-04-24

The capacitance and conductance measurements were carried out for c-Si solar cells, irradiated with 8 MeV electrons with doses ranging from 5kGy – 100kGy in order to investigate the anomalous degradation of the cells in the radiation harsh environments. Capacitance – Voltage measurements indicate that there is a slight reduction in the carrier concentration upon electron irradiation due to the creation of radiation induced defects. The conductance measurement results reveal that the interface state densities and the trap time constant increases with electron dose due to displacement damages in c-Si solar cells.

Surface and Bulk Characteristics of Cesium Iodide (CsI) coated Carbon (C) Fibers for High Power Microwave (HPM) Field Emission Cathodes

Science.gov (United States)

Vlahos, Vasilios; Morgan, Dane; Booske, John H.; Shiffler, Don

2008-11-01

CsI coated C fibers [1] are promising field emission cathodes for HPM applications. Ab initio computational modeling has shown that atomically-thin CsI coatings reduce the work function of C substrates by a surface dipole mechanism [2]. Characterization measurements of the composition and morphology of the CsI-coated C fibers are underway for determining the properties and characteristics of the following important regions of the fiber: (i) the surface on the tip of the fiber where the majority of electron emission is believed to occur, (ii) the surface covering the body of the fiber and its role on the emission properties of the system, and (iii) the interior volume of the fiber and its effects on the CsI surface re-supply process and rate. The results will be interpreted in terms of surface electronic properties and theoretical electron emission models. [1]D. Shiffler, et al., Phys. Plasmas 11 (2004) 1680. [2]V.Vlahos et al., Appl. Phys. Lett. 91 (2007) 144102.

On the c-Si surface passivation mechanism by the negative-charge-dielectric Al2O3

NARCIS (Netherlands)

Hoex, B.; Gielis, J.J.H.; Sanden, van de M.C.M.; Kessels, W.M.M.

2008-01-01

Al2 O3 is a versatile high- ¿ dielectric that has excellent surface passivation properties on crystalline Si (c-Si), which are of vital importance for devices such as light emitting diodes and high-efficiency solar cells. We demonstrate both experimentally and by simulations that the surface

Atomic-layer deposited Nb2O5 as transparent passivating electron contact for c-Si solar cells

NARCIS (Netherlands)

Macco, Bart; Black, Lachlan E.; Melskens, Jimmy; van de Loo, Bas W.H.; Berghuis, Willem Jan H.; Verheijen, Marcel A.; Kessels, Wilhelmus M.M.

2018-01-01

Passivating contacts based on metal oxides have proven to enable high energy conversion efficiencies for crystalline silicon (c-Si) solar cells at low processing complexity. In this work, the potential of atomic-layer deposited (ALD) Nb2O5 as novel electron-selective passivating contact is explored

ATDM LANL FleCSI: Topology and Execution Framework

Energy Technology Data Exchange (ETDEWEB)

Bergen, Benjamin Karl [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-06

FleCSI is a compile-time configurable C++ framework designed to support multi-physics application development. As such, FleCSI attempts to provide a very general set of infrastructure design patterns that can be specialized and extended to suit the needs of a broad variety of solver and data requirements. This means that FleCSI is potentially useful to many different ECP projects. Current support includes multidimensional mesh topology, mesh geometry, and mesh adjacency information, n-dimensional hashed-tree data structures, graph partitioning interfaces, and dependency closures (to identify data dependencies between distributed-memory address spaces). FleCSI introduces a functional programming model with control, execution, and data abstractions that are consistent with state-of-the-art task-based runtimes such as Legion and Charm++. The model also provides support for fine-grained, data-parallel execution with backend support for runtimes such as OpenMP and C++17. The FleCSI abstraction layer provides the developer with insulation from the underlying runtimes, while allowing support for multiple runtime systems, including conventional models like asynchronous MPI. The intent is to give developers a concrete set of user-friendly programming tools that can be used now, while allowing flexibility in choosing runtime implementations and optimizations that can be applied to architectures and runtimes that arise in the future. This project is essential to the ECP Ristra Next-Generation Code project, part of ASC ATDM, because it provides a hierarchically parallel programming model that is consistent with the design of modern system architectures, but which allows for the straightforward expression of algorithmic parallelism in a portably performant manner.

Process Optimization for High Efficiency Heterojunction c-Si Solar Cells Fabrication Using Hot-Wire Chemical Vapor Deposition: Preprint

Energy Technology Data Exchange (ETDEWEB)

Ai, Y.; Yuan, H. C.; Page, M.; Nemeth, W.; Roybal, L.; Wang, Q.

2012-06-01

The researchers extensively studied the effects of annealing or thermal history of cell process on the minority carrier lifetimes of FZ n-type c-Si wafers with various i-layer thicknesses from 5 to 60 nm, substrate temperatures from 100 to 350 degrees C, doped layers both p- and n-types, and transparent conducting oxide (TCO).

Photocarrier radiometry for predicting the degradation of electrical parameters of monocrystalline silicon (c-Si) solar cell irradiated by 100 KeV proton beams

International Nuclear Information System (INIS)

Song, P.; Liu, J.Y.; Yuan, H.M.; Oliullah, Md.; Wang, F.; Wang, Y.

2016-01-01

In this study, the monocrystalline silicon (c-Si) solar cell irradiated by 100 KeV proton beams at various fluences is investigated. A one-dimensional two-layer carrier density wave model has been developed to estimate the minority carrier lifetime of n-region and p-region of the non-irradiated c-Si solar cell by best fitting with the experimental photocarrier radiometry (PCR) signal (the amplitude and the phase). Furthermore, the lifetime is used to determine the initial defect density of the quasi-neutral region (QNR) of the solar cell to predict its I–V characteristics. The theoretically predicted short-circuit current density (J_s_c), and open-circuit voltage (V_o_c) of the non-irradiated samples are in good agreement with experiment. Then a three-region defect distribution model for the c-Si solar cell irradiated by proton beams is carried out to describe the defect density distribution according to Monte Carlo simulation results and the initial defect density of the non-irradiated sample. Finally, we find that the electrical measurements of J_s_c and V_o_c of the solar cells irradiated at different fluences using 100 KeV proton beams are consistent with the PCR predicting results.

Growing GaN LEDs on amorphous SiC buffer with variable C/Si compositions

Science.gov (United States)

Cheng, Chih-Hsien; Tzou, An-Jye; Chang, Jung-Hung; Chi, Yu-Chieh; Lin, Yung-Hsiang; Shih, Min-Hsiung; Lee, Chao-Kuei; Wu, Chih-I; Kuo, Hao-Chung; Chang, Chun-Yen; Lin, Gong-Ru

2016-01-01

The epitaxy of high-power gallium nitride (GaN) light-emitting diode (LED) on amorphous silicon carbide (a-SixC1−x) buffer is demonstrated. The a-SixC1−x buffers with different nonstoichiometric C/Si composition ratios are synthesized on SiO2/Si substrate by using a low-temperature plasma enhanced chemical vapor deposition. The GaN LEDs on different SixC1−x buffers exhibit different EL and C-V characteristics because of the extended strain induced interfacial defects. The EL power decays when increasing the Si content of SixC1−x buffer. The C-rich SixC1−x favors the GaN epitaxy and enables the strain relaxation to suppress the probability of Auger recombination. When the SixC1−x buffer changes from Si-rich to C-rich condition, the EL peak wavelengh shifts from 446 nm to 450 nm. Moreover, the uniform distribution contour of EL intensity spreads between the anode and the cathode because the traping density of the interfacial defect gradually reduces. In comparison with the GaN LED grown on Si-rich SixC1−x buffer, the device deposited on C-rich SixC1−x buffer shows a lower turn-on voltage, a higher output power, an external quantum efficiency, and an efficiency droop of 2.48 V, 106 mW, 42.3%, and 7%, respectively. PMID:26794268

CSI cardiac prevent 2015

Directory of Open Access Journals (Sweden)

S Ramakrishnan

2015-01-01

Full Text Available The CSI Cardiac Prevent 2015 was held at Hotel Taj Palace, New Delhi, on September 25-27, 2015. The major challenge was to create interest among cardiologists and physicians on preventive cardiology, a neglected area. The theme of the conference was "Innovations in Heart Disease Prevention.′′ This conference included "CSI at WHF Roadmap Workshop, Inauguration Ceremony, scientific program, plenary sessions, Nursing/Dietician track, Industry Exhibition, Social Events," Great India blood pressure Survey, and CSI Smart Heart App. A total of 848 delegates/faculties attended this conference against a total of 1140 people registered for the meeting.

Global Annual Final AC Yield Comparison between HCPV and c-Si PV

Directory of Open Access Journals (Sweden)

Juan Pablo Ferrer-Rodríguez

2015-01-01

Full Text Available A worldwide comparison of the annual yield between conventional c-Si photovoltaic (PV technology and high concentrated photovoltaic (HCPV technology is presented. The idea of this paper is to find the most appropriate locations for HCPV systems in terms of the annual energy produced when comparing to fixed tilt PV systems and two-axis oriented PY systems. For estimating the annual energy generation, the method of the Performance Ratio is used. For some locations with high annual direct normal irradiation values, which are distributed around the world, HCPV systems are found to be more advantageous than fixed tilt PV systems. World maps showing this comparison are presented.

H{sub 2}-Ar dilution for improved c-Si quantum dots in P-doped SiN{sub x}:H thin film matrix

Energy Technology Data Exchange (ETDEWEB)

Liu, Jia [Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); Zhang, Weijia, E-mail: zwjghx@126.com [Center of Condensed Matter and Material Physics, School of Physics and Nuclear Energy Engineering, Beihang University, Beijing, 100191 (China); Liu, Shengzhong, E-mail: szliu@dicp.ac.cn [Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); State key Laboratory of Catalysis, iChEM, Dalian Institute of Chemical Physics, Dalian National Laboratory for Clean Energy, Chinese Academy of Sciences, Dalian 116023 (China)

2017-02-28

Highlights: • Phosphorous-doped SiN{sub x}:H thin films containing c-Si QDs were prepared by PECVD in H{sub 2}-Ar mixed dilution under low temperature. • QD density and QD size can be controlled by tuning H{sub 2}/Ar flow ratio. • The sample prepared at the H{sub 2}/Ar flow ratio of 100/100 possesses both wide band gap and excellent conductivity. • Detail discussion has been presented for illustrating the influence of H{sub 2}/Ar mixed dilution on the crystallization process and P-doping. - Abstract: Phosphorus-doped hydrogenated silicon nitride (SiN{sub x}:H) thin films containing crystalline silicon quantum dot (c-Si QD) was prepared by plasma enhanced chemical vapor deposition (PECVD) using hydrogen-argon mixed dilution. The effects of H{sub 2}/Ar flow ratio on the structural, electrical and optical characteristics of as-grown P-doped SiN{sub x}:H thin films were systematically investigated. Experimental results show that crystallization is promoted by increasing the H{sub 2}/Ar flow ratio in dilution, while the N/Si atomic ratio is higher for thin film deposited with argon-rich dilution. As the H{sub 2}/Ar flow ratio varies from 100/100 to 200/0, the samples exhibit excellent conductivity owing to the large volume fraction of c-Si QDs and effective P-doping. By adjusting the H{sub 2}/Ar ratio to 100/100, P-doped SiN{sub x}:H thin film containing tiny and densely distributed c-Si QDs can be obtained. It simultaneously possesses wide optical band gap and high dark conductivity. Finally, detailed discussion has been made to analyze the influence of H{sub 2}-Ar mixed dilution on the properties of P-doped SiN{sub x}:H thin films.

Progress in the medicinal chemistry of silicon: C/Si exchange and beyond.

Science.gov (United States)

Fujii, Shinya; Hashimoto, Yuichi

2017-04-01

Application of silyl functionalities is one of the most promising strategies among various 'elements chemistry' approaches for the development of novel and distinctive drug candidates. Replacement of one or more carbon atoms of various biologically active compounds with silicon (so-called sila-substitution) has been intensively studied for decades, and is often effective for alteration of activity profile and improvement of metabolic profile. In addition to simple C/Si exchange, several novel approaches for utilizing silicon in medicinal chemistry have been suggested in recent years, focusing on the intrinsic differences between silicon and carbon. Sila-substitution offers great potential for enlarging the chemical space of medicinal chemistry, and provides many options for structural development of drug candidates.

Environmental Stability and Oxidation Behavior of HfO2-Si and YbGd(O) Based Environmental Barrier Coating Systems for SiCSiC Ceramic Matrix Composites

Science.gov (United States)

Zhu, Dongming; Farmer, Serene; McCue, Terry R.; Harder, Bryan; Hurst, Janet B.

2017-01-01

Ceramic environmental barrier coatings (EBC) and SiCSiC ceramic matrix composites (CMCs) will play a crucial role in future aircraft propulsion systems because of their ability to significantly increase engine operating temperatures, improve component durability, reduce engine weight and cooling requirements. Advanced EBC systems for SiCSiC CMC turbine and combustor hot section components are currently being developed to meet future turbine engine emission and performance goals. One of the significant material development challenges for the high temperature CMC components is to develop prime-reliant, environmental durable environmental barrier coating systems. In this paper, the durability and performance of advanced Electron Beam-Physical Vapor Deposition (EB-PVD) NASA HfO2-Si and YbGdSi(O) EBC bond coat top coat systems for SiCSiC CMC have been summarized. The high temperature thermomechanical creep, fatigue and oxidation resistance have been investigated in the laboratory simulated high-heat-flux environmental test conditions. The advanced NASA EBC systems showed promise to achieve 1500C temperature capability, helping enable next generation turbine engines with significantly improved engine component temperature capability and durability.

CsI Calorimeter for a Compton-Pair Telescope

Science.gov (United States)

Grove, Eric J.

We propose to build and test a hodoscopic CsI(Tl) scintillating-crystal calorimeter for a medium-energy γ-ray Compton and pair telescope. The design and technical approach for this calorimeter relies deeply on heritage from the Fermi LAT CsI Calorimeter, but it dramatically improves the low-energy performance of that design by reading out the scintillation light with silicon photomultipliers (SiPMs), making the technology developed for Fermi applicable in the Compton regime. While such a hodoscopic calorimeter is useful for an entire class of medium-energy γ-ray telescope designs, we propose to build it explicitly to support beam tests and balloon flight of the Proto-ComPair telescope, the development and construction of which was funded in a four-year APRA program beginning in 2015 ("ComPair: Steps to a Medium Energy γ-ray Mission" with PI J. McEnery of GSFC). That award did not include funding for its CsI calorimeter subsystem, and this proposal is intended to cover that gap. ComPair is a MIDEX-class instrument concept to perform a high-sensitivity survey of the γ-ray sky from 0.5 MeV to 500 MeV. ComPair is designed to provide a dramatic increase in sensitivity relative to previous instruments in this energy range (predominantly INTEGRAL/SPI and Compton COMPTEL), with the same transformative sensitivity increase - and corresponding scientific return- that the Fermi Large Area Telescope provided relative to Compton EGRET. To enable transformative science over a broad range of MeV energies and with a wide field of view, ComPair is a combined Compton telescope and pair telescope employing a silicon-strip tracker (for Compton scattering and pair conversion and tracking) and a solid-state CdZnTe calorimeter (for Compton absorption) and CsI calorimeter (for pair calorimetry), surrounded by a plastic scintillator anti-coincidence detector. Under the current proposal, we will complete the detailed design, assembly, and test of the CsI calorimeter for the risk

Photocarrier radiometry for predicting the degradation of electrical parameters of monocrystalline silicon (c-Si) solar cell irradiated by 100 KeV proton beams

Energy Technology Data Exchange (ETDEWEB)

Song, P. [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); Liu, J.Y., E-mail: ljywlj@hit.edu.cn [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); State Key Laboratory of Robotics and System (HIT), Harbin 150001 (China); Yuan, H.M.; Oliullah, Md.; Wang, F. [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); Wang, Y., E-mail: songpengkevin@126.com [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); State Key Laboratory of Robotics and System (HIT), Harbin 150001 (China)

2016-09-15

In this study, the monocrystalline silicon (c-Si) solar cell irradiated by 100 KeV proton beams at various fluences is investigated. A one-dimensional two-layer carrier density wave model has been developed to estimate the minority carrier lifetime of n-region and p-region of the non-irradiated c-Si solar cell by best fitting with the experimental photocarrier radiometry (PCR) signal (the amplitude and the phase). Furthermore, the lifetime is used to determine the initial defect density of the quasi-neutral region (QNR) of the solar cell to predict its I–V characteristics. The theoretically predicted short-circuit current density (J{sub sc}), and open-circuit voltage (V{sub oc}) of the non-irradiated samples are in good agreement with experiment. Then a three-region defect distribution model for the c-Si solar cell irradiated by proton beams is carried out to describe the defect density distribution according to Monte Carlo simulation results and the initial defect density of the non-irradiated sample. Finally, we find that the electrical measurements of J{sub sc} and V{sub oc} of the solar cells irradiated at different fluences using 100 KeV proton beams are consistent with the PCR predicting results.

Heat enhancement of radiation resistivity of evaporated CsI, KI and KBr photocathodes

CERN Document Server

Tremsin, A S

2000-01-01

The photoemissive stability of as-deposited and heat-treated CsI, KI and KBr evaporated thin films under UV radiation is examined in this paper. After the deposition, some photocathodes were annealed for several hours at 90 deg. C in vacuum and their performance was then compared to the performance of non-heated samples. We observed that the post-evaporation thermal treatment not only increases the photoyield of CsI and KI photocathodes in the spectral range of 115-190 nm, but also reduces CsI, KI and KBr photocurrent degradation that occurs after UV irradiation. KBr evaporated layers appeared to be more radiation-resistant than CsI and KI layers. Post-deposition heat treatment did not result in any significant variation of KBr UV sensitivity.

Origin of the fast magnetization tunneling in [Ni(hmp)(tBuEtOH)Cl]4

Science.gov (United States)

Lawrence, Jon; Yang, En-Che

2005-03-01

High-frequency (40-360 GHz), angle-dependent EPR data have been collected for single-crystals of [Ni(hmp)(dmb)Cl]4, and [Ni0.02Zn0.98(hmp)(dmb)Cl]4. The all-nickel complex behaves as a single-molecule magnet (SMM) at low temperatures, displaying hysteresis and magnetic quantum tunneling. However, in spite of its high symmetry (S4), the relaxation is found to be very fast. We show that the origin of this behavior is related to a 4^th-order transverse crystal-field interaction, B4^4(S+^4 + S-^4), which produces a significant tunnel-splitting (˜10 MHz) of the ms = ±4 ground state of this S = 4 SMM. The fourth-order (B4^4) and uniaxial (D) crystal-field strengths can be related to the directionality and magnitude of the single-ion interactions (Di and Ei) at the individual Ni^II sites, as determined for the doped crystals. Variable-temperature EPR measurements also reveal the locations of excited spin states (S = 3, 2, etc..), enabling estimates of intra-molecular exchange coupling strengths.

CSI cardiac prevent 2015

OpenAIRE

S Ramakrishnan; Manisha Kaushik

2015-01-01

The CSI Cardiac Prevent 2015 was held at Hotel Taj Palace, New Delhi, on September 25-27, 2015. The major challenge was to create interest among cardiologists and physicians on preventive cardiology, a neglected area. The theme of the conference was "Innovations in Heart Disease Prevention.′′ This conference included "CSI at WHF Roadmap Workshop, Inauguration Ceremony, scientific program, plenary sessions, Nursing/Dietician track, Industry Exhibition, Social Events," Great India blood pressur...

Oral health of female prisoners in HMP Holloway: implications for oral health promotion in UK prisons

NARCIS (Netherlands)

Rouxel, P.; Duijster, D.; Tsakos, G.; Watt, R.G.

2013-01-01

Objectives This study describes the oral health status and associated risk factors in a sample of female prisoners and compares their oral health to that of the female population from the 2009 Adult Dental Health Survey. Method A random sample of prisoners was selected from HMP Holloway, London.

Role of field-effect on c-Si surface passivation by ultrathin (2-20 nm) atomic layer deposited Al2O3

NARCIS (Netherlands)

Terlinden, N.M.; Dingemans, G.; Sanden, van de M.C.M.; Kessels, W.M.M.

2010-01-01

Al2O3 synthesized by plasma-assisted atomic layer deposition yields excellent surface passivation of crystalline silicon (c-Si) for films down to ~ 5 nm in thickness. Optical second-harmonic generation was employed to distinguish between the influence of field-effect passivation and chemical

Improved reconstruction for IDEAL spiral CSI

DEFF Research Database (Denmark)

Hansen, Rie Beck; Mariager, Christian; Laustsen, Christoffer

2017-01-01

In this study we demonstrate how reconstruction for IDEAL spiral CSI (spectroscopic imaging scheme developed for hyperpolarized dynamic metabolic MR imaging) can be improved by using regularization with a sparsity constraint. By exploiting sparsity of the spectral domain, IDEAL spiral CSI can...

Investigation of spectral distribution and variation of irradiance with the passage time of CSI lamps which constitute a solar simulator; Solar simulator ni shiyosuru CSI lamp no supekutoru bunpu, hosha shodo no keiji henka ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, T; Yamada, T; Noguchi, T [Japan Quality Assurance Organization, Tokyo (Japan)

1997-11-25

Study was made on time-variation of the performance of CSI lamps for solar simulators. In order to accurately evaluate the standard heat collection performance of solar systems in a room, MITI installed an artificial solar light source in the Solar Techno-Center of Japan Quality Assurance Organization for trial use and evaluation. CSI lamp is superior in durability, and can simulate the solar light in the daytime. The light source is composed of 72 metal halide lamps of 1kW arranged in a plane of 3.5times3.5m. The study result on time-variation of a spectral distribution and irradiance by intermittent switching of lamps showed a sufficient durability of 2000h. To ensure the accuracy of a solar heat collector measurement system enough, periodic calibration is being carried out using reference goods. To ensure the reliability and stability for a switching system, periodic maintenance of a power source, stabilizer and electric system is also being carried out in addition to CSI lamps. The stable irradiance and accuracy are being kept by such maintenance and periodic exchange of lamps. 6 figs., 4 tabs.

Simulated UO{sub 2} fuel containing CsI by spark plasma sintering

Energy Technology Data Exchange (ETDEWEB)

Wangle, T. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany); Czech Technical University in Prague, Faculty of Nuclear Sciences and Physical Engineering, Břehová 7, Praha 1, 115 19 (Czech Republic); Tyrpekl, V. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany); Cologna, M., E-mail: marco.cologna@ec.europa.eu [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany); Somers, J. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany)

2015-11-15

Herein, an innovative preparation procedure has been deployed enabling, for the first time, the incorporation of volatile fission product simulant into highly dense nuclear fuel pellets. Highly volatile fission products were embedded in a dense UO{sub 2} matrix in the form of CsI by simply mixing starting materials and consolidation in a Spark Plasma Sintering step at 1000 °C with a 5 min dwell time. CsI particles were evenly distributed throughout the pellet and were located at the grain boundaries. The sintering rate is dependent on the O/U ratio of the powder. Addition of CsI also acts as a sintering aid, reducing the temperature of maximum densification. - Highlights: • A new method was developed to incorporation of volatile fission products simulants into dense nuclear fuel pellets. • CsI doped UO{sub 2} pellets were synthetized for the first time, by Spark Plasma Sintering. • The sintering rate in Spark Plasma Sintering is dependent on the O/U ratio of UO{sub 2+x}.

Non-Cartesian Parallel Imaging Reconstruction of Undersampled IDEAL Spiral 13C CSI Data

DEFF Research Database (Denmark)

Hansen, Rie Beck; Hanson, Lars G.; Ardenkjær-Larsen, Jan Henrik

scan times based on spatial information inherent to each coil element. In this work, we explored the combination of non-cartesian parallel imaging reconstruction and spatially undersampled IDEAL spiral CSI1 acquisition for efficient encoding of multiple chemical shifts within a large FOV with high...

Influence of air exposure on CsI photocathodes

Energy Technology Data Exchange (ETDEWEB)

Xie, Yuguang, E-mail: ygxie@mail.ihep.ac.cn [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics, CAS and University of Science and Technology of China, Beijing 100049 (China); Zhang, Aiwu; Liu, Yingbiao [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics, CAS and University of Science and Technology of China, Beijing 100049 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Hongbang [Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Guangxi University, Naning 530004 (China); Hu, Tao; Zhou, Li; Cai, Xiao; Fang, Jian; Yu, Boxiang [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics, CAS and University of Science and Technology of China, Beijing 100049 (China); Ge, Yongshuai [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics, CAS and University of Science and Technology of China, Beijing 100049 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Lue, Qiwen [Shanxi University, Taiyuan 030006 (China); Sun, Xilei; Sun, Lijun; Xue, Zheng [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics, CAS and University of Science and Technology of China, Beijing 100049 (China); Xie, Yigang; Zheng, Yangheng [Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Lue, Junguang [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics, CAS and University of Science and Technology of China, Beijing 100049 (China)

2012-10-11

We investigate the influence of air exposure on the quantum efficiency (QE) and surface morphology of CsI photocathodes (PCs), at relative humidities (RH) higher than 80% down to nearly 3% (both at room temperature) and a 60 Degree-Sign C baking condition. By atomic force microscopy (AFM) surface analysis, it is clearly seen that RH >60% speeds up water film formation and CsI dissolution on the surface of the photocathode at the minute scale, while both grain size and QE change slowly at RH <30% at the hour scale. In the baking environment, the peak QE decreases less than 1.5% (absolute) within one week, and a stainless steel substrate and electron beam evaporation technique tend to effectively weaken the influence of air. With an Au-coated FR-4 substrate, the QE degradation is found to strongly depend on wavelength in the range of 120-210 nm. According to spectra of X-ray photoelectron spectroscopy (XPS), an excess of cesium was observed and the chemical reaction between water and CsI when exposed to humid air is proved. It is found that carbon, and not H{sub 2}O or O{sub 2}, is the main pollutant in the baking condition.

The TiO2 Refraction Film for CsI Scintillator

OpenAIRE

C. C. Chen; C. W. Hun; C. J. Wang; C. Y. Chen; J. S. Lin; K. J. Huang

2015-01-01

Cesium iodide (CsI) melt was injected into anodic aluminum oxide (AAO) template and was solidified to CsI column. The controllable AAO channel size (10~500 nm) can makes CsI column size from 10 to 500 nm in diameter. In order to have a shorter light irradiate from each singe CsI column top to bottom the AAO template was coated a TiO2 nano-film. The TiO2 film acts a refraction film and makes X-ray has a shorter irradiation path in the CsI crystal making a stronger the photo-electron signal. Wh...

Effect of non-magnetic intermediate layer on film structure, magnetic properties, and noise characteristics of FeCSi soft magnetic multilayers

International Nuclear Information System (INIS)

Kawano, Hiroyasu; Morikawa, Takeshi; Matsumoto, Koji; Shono, Keiji

2004-01-01

The film structures, magnetic properties, and noise characteristics of soft magnetic multilayers with alternately stacked FeCSi soft magnetic layers and non-magnetic intermediate layers were investigated. The FeCSi layers in an as-deposited multilayer with C or Ta intermediate layers had the same nano-sized fine crystalline grains and low media noise as an as-deposited FeCSi monolayer. Amorphous C intermediate layers suppressed the amplitude of spike noise especially well. In contrast, FeCSi layers in an as-deposited multilayer with Cr or Ti intermediate layers were composed of coarse crystalline grains, which increased the media noise. The crystallographic match at the interface between the layers in a multilayer could explain these phenomena. The similarity of the atomic arrangement at the interface between layers and the crystallographic match of less than a few percent for the distance between atoms crystallized FeCSi layers with nano-sized fine crystalline grains into ones with coarse crystalline grains during deposition

MIMO channel capacity with full CSI at Low SNR

KAUST Repository

Tall, Abdoulaye

2012-10-01

In this paper, we characterize the ergodic capacity of Multiple Input Multiple Output (MIMO) Rayleigh fading channels with full channel state information (CSI) at both the transmitter (CSI-T) and the receiver (CSI-R) at asymptotically low signal-to-noise ratio (SNR). A simple analytical expression of the capacity is derived for any number of transmit and receive antennas. This characterization clearly shows the substantial gain in terms of capacity over the no CSI-T case and gives a good insight on the effect of the number of antennas used. In addition, an On-Off transmission scheme is proposed and is shown to be asymptotically capacity-achieving. © 2012 IEEE.

Surface chemical analysis and ab initio investigations of CsI coated C fiber cathodes for high power microwave sources

Science.gov (United States)

Vlahos, Vasilios; Morgan, Dane; LaCour, Matthew; Golby, Ken; Shiffler, Don; Booske, John H.

2010-02-01

CsI coated C fiber cathodes are promising electron emitters utilized in field emission applications. Ab initio calculations, in conjunction with experimental investigations on CsI-spray coated C fiber cathodes, were performed in order to better understand the origin of the low turn-on E-field obtained, as compared to uncoated C fibers. One possible mechanism for lowering the turn-on E-field is surface dipole layers reducing the work function. Ab initio modeling revealed that surface monolayers of Cs, CsI, Cs2O, and CsO are all capable of producing low work function C fiber cathodes (1 eV<Φ<1.5 eV), yielding a reduction in the turn-on E-field by as much as ten times, when compared to the bare fiber. Although a CsI-containing aqueous solution is spray deposited on the C fiber surface, energy dispersive x-ray spectroscopy and scanning auger microscopy measurements show coabsorption of Cs and I into the fiber interior and Cs and O on the fiber surface, with no surface I. It is therefore proposed that a cesium oxide (CsxOy) surface coating is responsible, at least in part, for the low turn E-field and superior emission characteristics of this type of fiber cathode. This CsxOy layer could be formed during preconditioning heating. CsxOy surface layers cannot only lower the fiber work function by the formation of surface dipoles (if they are thin enough) but may also enhance surface emission through their ability to emit secondary electrons due to a process of grazing electron impact. These multiple electron emission processes may explain the reported 10-100 fold reduction in the turn-on E-field of coated C fibers.

Instruments for assessing the burden of informal caregiving for stroke patients in clinical practice: a comparison of CSI, CRA, SCQ and self-rated burden.

Science.gov (United States)

van Exel, N Job A; Scholte op Reimer, Wilma J M; Brouwer, Werner B F; van den Berg, Bernard; Koopmanschap, Marc A; van den Bos, Geertrudis A M

2004-03-01

To compare the feasibility, convergent and clinical validity of three commonly used burden scales: Caregiver Strain Index (CSI), Caregiver Reaction Assessment (CRA) and Sense of Competence Questionnaire (SCQ), with a self-developed single question on self-rated burden (SRB). Stroke patients receiving support from an informal caregiver (n = 148) and their caregivers were followed up to six months after stroke. Feasibility was assessed with several measures of missing values. Convergent validity was assessed on the basis of the correlation patterns between the burden scales, and clinical validity through evaluation of expected associations between levels of burden and explanatory patients' and caregivers' characteristics. Missing values were less often observed on CSI and SRB than SCQ and CRA. Significant correlation coefficients (p CRA. Evidence for clinical validity was strongest for CSI and SRB, based on associations between higher burden scores and patients' disability, and patients' and caregivers' poor level of health-related quality of life (all p CRA. SRB could be used for quick screening of caregivers at risk. CSI is indicated for further diagnosis of the burden of informal caregivers.

The Status of GLAST CsI Calorimeter

Energy Technology Data Exchange (ETDEWEB)

Chekhtman, A.

2003-09-18

GLAST is a gamma-ray observatory for celestial sources in the energy range from 20 MeV to 300 GeV. This is NASA project with launch anticipated in 2006. The principal instrument of the GLAST mission is the Large Area Telescope (LAT), consisting of an Anti Coincidence Detector (ACD), a silicon-strip detector Tracker (TKR) and a hodoscopic CsI Calorimeter (CAL). It consists of 16 identical modules arranged in a 4 x 4 array. Each module has horizontal dimensions 38 x 38 cm{sup 2} and active thickness 8.5 radiation length. It contains 96 CsI (Tl) crystals arranged in 8 layers with 12 crystals per layer. The scintillation light is measured by PIN photodiodes mounted on both ends of each crystal. The sum of signals at the two ends of the crystal provides the energy measurement. The difference in these signals provides the position measurement along the crystal. The calorimeter was designed to meet the goals of good energy resolution (better than 10% for photon energies 100 MeV-100 GeV), position resolution of {approx} 1 mm for photon energies > 1 GeV, and a rejection factor of > 100 for charged cosmic rays, under limitations on calorimeter weight (95 kg per module) and power consumption (6 W per module). The Monte Carlo simulation and prototype beam test results confirm that proposed design meets the requirements. Calorimeter production is planned to start in 2003.

Ab initio study of the effects of thin CsI coatings on the work function of graphite cathodes

Science.gov (United States)

Vlahos, Vasilios; Booske, John H.; Morgan, Dane

2007-10-01

Cesium-iodide (CsI)-coated graphite cathodes are promising electron sources for high power microwave generators, but the mechanism driving the improved emission is not well understood. Therefore, an ab initio modeling investigation on the effects of thin CsI coatings on graphite has been carried out. It is demonstrated that the CsI coatings reduce the work function of the system significantly through a mechanism of induced dipoles. The results suggest that work function modification is a major contribution to the improved emission seen when CsI coatings are applied to C.

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla

2011-11-01

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a MIMO-relay node. The channel state information (CSI) available at the relay node is assumed to be imperfect. We consider robust designs for two models of CSI error. The first model is a stochastic error (SE) model, where the probability distribution of the CSI error is Gaussian. This model is applicable when the imperfect CSI is mainly due to errors in channel estimation. For this model, we propose robust minimum sum mean square error (SMSE), MSE-balancing, and relay transmit power minimizing precoder designs. The next model for the CSI error is a norm-bounded error (NBE) model, where the CSI error can be specified by an uncertainty set. This model is applicable when the CSI error is dominated by quantization errors. In this case, we adopt a worst-case design approach. For this model, we propose a robust precoder design that minimizes total relay transmit power under constraints on MSEs at the destination nodes. We show that the proposed robust design problems can be reformulated as convex optimization problems that can be solved efficiently using interior-point methods. We demonstrate the robust performance of the proposed design through simulations. © 2011 IEEE.

Characterization of capsaicin synthase and identification of its gene (csy1) for pungency factor capsaicin in pepper (Capsicum sp.)

Science.gov (United States)

Prasad, B. C. Narasimha; Kumar, Vinod; Gururaj, H. B.; Parimalan, R.; Giridhar, P.; Ravishankar, G. A.

2006-01-01

Capsaicin is a unique alkaloid of the plant kingdom restricted to the genus Capsicum. Capsaicin is the pungency factor, a bioactive molecule of food and of medicinal importance. Capsaicin is useful as a counterirritant, antiarthritic, analgesic, antioxidant, and anticancer agent. Capsaicin biosynthesis involves condensation of vanillylamine and 8-methyl nonenoic acid, brought about by capsaicin synthase (CS). We found that CS activity correlated with genotype-specific capsaicin levels. We purified and characterized CS (≈35 kDa). Immunolocalization studies confirmed that CS is specifically localized to the placental tissues of Capsicum fruits. Western blot analysis revealed concomitant enhancement of CS levels and capsaicin accumulation during fruit development. We determined the N-terminal amino acid sequence of purified CS, cloned the CS gene (csy1) and sequenced full-length cDNA (981 bp). The deduced amino acid sequence of CS from full-length cDNA was 38 kDa. Functionality of csy1 through heterologous expression in recombinant Escherichia coli was also demonstrated. Here we report the gene responsible for capsaicin biosynthesis, which is unique to Capsicum spp. With this information on the CS gene, speculation on the gene for pungency is unequivocally resolved. Our findings have implications in the regulation of capsaicin levels in Capsicum genotypes. PMID:16938870

The Development of Environmental Barrier Coatings for SiCSiC Ceramic Matrix Composites: Challenges and Opportunities

Science.gov (United States)

Zhu, Dongming

2014-01-01

Environmental barrier coatings (EBCs) and SiC/SiC ceramic matrix composites (CMCs) systems will play a crucial role in future turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures, reduce engine weight and cooling requirements. The development of prime-reliant environmental barrier coatings is a key to enable the applications of the envisioned CMC components to help achieve next generation engine performance and durability goals. This paper will primarily address the performance requirements and design considerations of environmental barrier coatings for turbine engine applications. The emphasis is placed on current candidate environmental barrier coating systems for SiCSiC CMCs, their performance benefits and design limitations in long-term operation and combustion environments. Major technical barriers in developing advanced environmental barrier coating systems, the coating integrations with next generation CMC turbine components having improved environmental stability, cyclic durability and system performance will be described. The development trends for turbine environmental barrier coating systems by utilizing improved compositions, state-of-the-art processing methods, and simulated environment testing and durability modeling will be discussed.

The Present Development of CsI Rich Detectors for the ALICE Experiment at CERN

CERN Document Server

Nappi, E; Colonna, N; Di Mauro, A; Elia, D; Galantucci, L; Ghidini, B; Grimaldi, A; Goret, B; Monno, E; Paic, G; Piuz, François; Posa, F; Raynaud, J; Santiard, Jean-Claude; Tomasicchio, G; Williams, T D; Ljubicic, A; Tustonic, T; Stucchi, S

1999-01-01

The ALICE Collaboration plans to implement a 12m^2 array consisting of 7 proximity focussed C6F^14 liquid radiator RICH modules devoted to the particle identification in the momentum range: 1 GeV/c - 3.5 GeV/c for pions and kaons. A large area CSI-RICH prototype has been designed and built with the aim to validate the detector parameter assumptions made to predict the performance of the High Momentum Particle Identification System (HMPID) of the ALICE Experiment. The main elements of the prototype will be described with emphasis on the engineering solutions adopted. First results from the analysis of multitrack events recorded with this prototype exposed to hadron beams at the CERN SPS will be discussedList of FiguresFigure 1 General view of the ALICE lay-outFigure 2 Schematic layout of the fast CsI-RICHFigure 3 Perspective view of the HMPID layout with the seven RICH modules tilted according to their position with respect to the interaction vertex. The frame that supports the detectors is also shownFigure 4 ...

Proton magnetic resonance chemical shift imaging (1H CSI)-directed stereotactic biopsy

International Nuclear Information System (INIS)

Son, B.-C.; Kim, B.-C.; Kang, J.-K.; Choi, B.-G.; Kim, E.-N.; Baik, H.-M.; Choe, B.-Y.; Naruse, S.

2001-01-01

Introduction. To add metabolic information during stereotactic biopsy target selection, the authors adopted proton chemical shift imaging ( 1 H CSI)-directed stereotactic biopsy. Currently, proton single voxel spectroscopy (SVS) technique has been reported in stereotactic biopsy. We performed 1 H CSI in combination with a stereotactic headframe and selected targets according to local metabolic information, and evaluated the pathological results. Patients and Method. The 1 H CSI-directed stereotactic biopsy was performed in four patients. 1 H CSI and conventional Gd-enhancement stereotactic MRI were performed simultaneously after the fitting of a stereotactic frame. After reconstructing the metabolic maps of N-acetylaspartate (NAA)/phosphocreatine (Cr), phosphocholine (Cho)/Cr, and Lactate/Cr ratios, focal areas of increased Cho/Cr ratio and Lac/Cr ratios were selected as target sites in the stereotactic MR images. Result. 1 H CSI is possible with the stereotactic headframe in place. No difficulty was experienced performing 1 H CSI or making a diagnosis. Pathological samples taken from areas of increased Cho/Cr ratios and decreased NAA/Cr ratios provided information upon increased cellularity, mitoses and cellular atypism, and facilitated diagnosis. Pathological samples taken from areas of increased Lac/ Cr ratio snowed predominant feature of necrosis. Conclusion. 1 H CSI was feasible with the stereotactic headframe in place. The final pathological results obtained were concordant with the local metabolic information from 1 H CSI. We believe that 1 H CSI-directed stereotactic biopsy has the potential to significantly improve the accuracy of stereotactic biopsy targeting. (author)

Impact of one-dimensional photonic crystal back reflector in thin-film c-Si solar cells on efficiency

Science.gov (United States)

Jalali, Tahmineh

2018-05-01

In this work, the effect of one-dimensional photonic crystal on optical absorption, which is implemented at the back side of thin-film crystalline silicon (c-Si) solar cells, is extensively discussed. The proposed structure acts as a Bragg reflector which reflects back light to the active layer as well as nanograting which couples the incident light to enhance optical absorption. To understand the optical mechanisms responsible for the enhancement of optical absorption, quantum efficiency and current density for all structures are calculated and the effect of influential parameters, such as grating period is investigated. The results confirm that our proposed structure have a great deal for substantial efficiency enhancement in a broad range from 400 to 1100 nm.

Robustness up to 400°C of the passivation of c-Si by p-type a-Si:H thanks to ion implantation

Science.gov (United States)

Defresne, A.; Plantevin, O.; Roca i Cabarrocas, Pere

2016-12-01

Heterojunction solar cells based on crystalline silicon (c-Si) passivated by hydrogenated amorphous silicon (a-Si:H) thin films are one of the most promising architectures for high energy conversion efficiency. Indeed, a-Si:H thin films can passivate both p-type and n-type wafers and can be deposited at low temperature (layers, in particular p-type a-Si:H, show a dramatic degradation in passivation quality above 200°C. Yet, annealing at 300 - 400°C the TCO layer and metallic contacts is highly desirable to reduce the contact resistance as well as the TCO optical absorption. In this work, we show that as expected, ion implantation (5 - 30 keV) introduces defects at the c-Si/a-Si:H interface which strongly degrade the effective lifetime, down to a few micro-seconds. However, the passivation quality can be restored and lifetime values can be improved up to 2 ms over the initial value with annealing. We show here that effective lifetimes above 1 ms can be maintained up to 380°C, opening up the possibility for higher process temperatures in silicon heterojunction device fabrication.

Back scattering involving embedded silicon nitride (SiN) nanoparticles for c-Si solar cells

Science.gov (United States)

Ghosh, Hemanta; Mitra, Suchismita; Siddiqui, M. S.; Saxena, A. K.; Chaudhuri, Partha; Saha, Hiranmay; Banerjee, Chandan

2018-04-01

A novel material, structure and method of synthesis for dielectric light trapping have been presented in this paper. First, the light scattering behaviour of silicon nitride nanoparticles have been theoretically studied in order to find the optimized size for dielectric back scattering by FDTD simulations from Lumerical Inc. The optical results have been used in electrical analysis and thereby, estimate the effect of nanoparticles on efficiency of the solar cells depending on substrate thickness. Experimentally, silicon nitride (SiN) nanoparticles have been formed using hydrogen plasma treatment on SiN layer deposited by Plasma Enhanced Chemical Vapour Deposition (PECVD). The size and area coverage of the nanoparticles were controlled by varying the working pressure, power density and treatment duration. The nanoparticles were integrated with partial rear contact c-Si solar cells as dielectric back reflector structures for the light trapping in thin silicon solar cells. Experimental results revealed the increases of current density by 2.7% in presence of SiN nanoparticles.

Perception-Induced Effects of Corporate Social Irresponsibility (CSiR) for Stereotypical and Admired Firms.

Science.gov (United States)

Voliotis, Seraphim; Vlachos, Pavlos A; Epitropaki, Olga

2016-01-01

How do stakeholders react to Corporate Social Irresponsibility (CSiR)? What are the emotional mechanisms and behavioral outcomes following CSiR perception? The psychology of CSR literature has yet to address these important questions and has largely considered CSR and CSiR as the opposite poles of the same continuum. In contrast, we view CSR and CSiR as distinct constructs and theorize about the cognitive (perceptual), emotional, and behavioral effects of CSiR activity on observers (i.e., primary and secondary stakeholders) building on theories of intergroup perception. Specifically, building on the Stereotype Content Model (SCM; Fiske et al., 2002) and the BIAS map (i.e., Behaviors from Intergroup Affect and Stereotypes; Cuddy et al., 2007)-which extends the SCM by predicting behavioral responses-we make predictions on potential stakeholder reactions to CSiR focusing on two practice-relevant cases: (a) a typical for-profit firm that engages in a CSiR activity, (b) an atypical admired firm that engages in CSiR activity.

Langley's CSI evolutionary model: Phase O

Science.gov (United States)

Belvin, W. Keith; Elliott, Kenny B.; Horta, Lucas G.; Bailey, Jim P.; Bruner, Anne M.; Sulla, Jeffrey L.; Won, John; Ugoletti, Roberto M.

1991-01-01

A testbed for the development of Controls Structures Interaction (CSI) technology to improve space science platform pointing is described. The evolutionary nature of the testbed will permit the study of global line-of-sight pointing in phases 0 and 1, whereas, multipayload pointing systems will be studied beginning with phase 2. The design, capabilities, and typical dynamic behavior of the phase 0 version of the CSI evolutionary model (CEM) is documented for investigator both internal and external to NASA. The model description includes line-of-sight pointing measurement, testbed structure, actuators, sensors, and real time computers, as well as finite element and state space models of major components.

The adsorption of Sr(II) and Cs(I) ions by irradiated Saccharomyces cerevisiae

International Nuclear Information System (INIS)

Yiming Tan; Jundong Feng; Liang Qiu; Zhentian Zhao; Xiaohong Zhang; Haiqian Zhang

2017-01-01

Adsorption behavior and mechanism of Sr(II) and Cs(I) in single and binary solutions using irradiated Saccharomyces cerevisiae was investigated. The effects of several environmental factors on Sr(II) and Cs(I) adsorption to irradiated Saccharomyces cerevisiae was determined. The equilibrium experimental data were simulated by different kinetic models and isotherm models. The combined effect of Sr(II) and Cs(I) on Saccharomyces cerevisiae is generally antagonistic. SEM and EDS analyses indicate that crystals formed on the cell surface are precipitate of Sr(II) and Cs(I), respectively. (author)

CsI calorimeter of the CMD-3 detector

International Nuclear Information System (INIS)

Aulchenko, V.M.; Bondar, A.E.; Erofeev, A.L.; Kovalenko, O.A.; Kozyrev, A.N.; Kuzmin, A.S.; Logashenko, I.B.; Razuvaev, G.P.; Ruban, A.A.; Shebalin, V.E.; Shwartz, B.A.; Talyshev, A.A.; Titov, V.M.; Yudin, Yu.V.; Epifanov, D.A.

2015-01-01

The VEPP-2000 e + e − collider has been operated at Budker Institute of Nuclear Physics since 2010. The experiments are performed with two detectors CMD-3 and SND. The calorimetry at the CMD-3 detector is based on three subsystems, two coaxial barrel calorimeters—Liquid Xenon Calorimeter and crystal CsI calorimeter, and endcap calorimeter with BGO crystals. This paper describes the CsI calorimeter of the CMD-3 detector. The calorimeter design, its electronics and calibration procedures are discussed

Contact Selectivity Engineering in a 2 μm Thick Ultrathin c-Si Solar Cell Using Transition-Metal Oxides Achieving an Efficiency of 10.8.

Science.gov (United States)

Xue, Muyu; Islam, Raisul; Meng, Andrew C; Lyu, Zheng; Lu, Ching-Ying; Tae, Christian; Braun, Michael R; Zang, Kai; McIntyre, Paul C; Kamins, Theodore I; Saraswat, Krishna C; Harris, James S

2017-12-06

In this paper, the integration of metal oxides as carrier-selective contacts for ultrathin crystalline silicon (c-Si) solar cells is demonstrated which results in an ∼13% relative improvement in efficiency. The improvement in efficiency originates from the suppression of the contact recombination current due to the band offset asymmetry of these oxides with Si. First, an ultrathin c-Si solar cell having a total thickness of 2 μm is shown to have >10% efficiency without any light-trapping scheme. This is achieved by the integration of nickel oxide (NiO x ) as a hole-selective contact interlayer material, which has a low valence band offset and high conduction band offset with Si. Second, we show a champion cell efficiency of 10.8% with the additional integration of titanium oxide (TiO x ), a well-known material for an electron-selective contact interlayer. Key parameters including V oc and J sc also show different degrees of enhancement if single (NiO x only) or double (both NiO x and TiO x ) carrier-selective contacts are integrated. The fabrication process for TiO x and NiO x layer integration is scalable and shows good compatibility with the device.

Hard X-ray photoelectron spectroscopy study for transport behavior of CsI in heating test simulating a BWR severe accident condition: Chemical effects of boron vapors

Energy Technology Data Exchange (ETDEWEB)

Okane, T., E-mail: okanet@spring8.or.jp [Quantum Beam Science Center, Japan Atomic Energy Agency, 1-1-1 Kouto, Sayo-cho, Hyogo, 679-5148 (Japan); Kobata, M. [Quantum Beam Science Center, Japan Atomic Energy Agency, 1-1-1 Kouto, Sayo-cho, Hyogo, 679-5148 (Japan); Sato, I. [Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Ibaraki, 311-1393 (Japan); Kobayashi, K. [Quantum Beam Science Center, Japan Atomic Energy Agency, 1-1-1 Kouto, Sayo-cho, Hyogo, 679-5148 (Japan); Osaka, M. [Nuclear Science and Engineering Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Ibaraki, 311-1393 (Japan); Yamagami, H. [Quantum Beam Science Center, Japan Atomic Energy Agency, 1-1-1 Kouto, Sayo-cho, Hyogo, 679-5148 (Japan); Faculty of Science, Kyoto Sangyo University, Motoyama, Kamigamo, Kita-ku, Kyoto, 603-8555 (Japan)

2016-02-15

Highlights: • We have clarified the temperature-dependent chemical forms of Cs/I products. • We have examined the CsI-decomposing effects of B{sub 2}O{sub 3} vapor. • The possibility of Cs re-evaporation from CsI-deposited surface is suggested. • We have demonstrated the usefulness of HAXPES on FP chemistry. - Abstract: Transport behavior of CsI in the heating test, which simulated a BWR severe accident, was investigated by hard X-ray photoelectron spectroscopy (HAXPES) with an emphasis on the chemical effect of boron vapors. CsI deposited on metal tube at temperatures ranging from 150 °C to 750 °C was reacted with vapor/aerosol B{sub 2}O{sub 3}, and the chemical form of reaction products on the sample surface was examined from the HAXPES spectra of core levels, e.g., Ni 2p, Cs 3d and I 3d levels, and valence band. For the samples at ∼300 °C, while the chemical form of major product on the sample surface without an exposure to B{sub 2}O{sub 3} was suggested to be CsI from the HAXPES spectra, an intensity ratio of Cs/I was dramatically reduced at the sample surface after the reaction with B{sub 2}O{sub 3}. The results suggest the possibility of significant decomposition of deposited CsI induced by the chemical reaction with B{sub 2}O{sub 3} at specific temperatures.

On Line Stator Resistance Tuning of DTC Control CSI Fed IM Drives

OpenAIRE

PANNEER SELVAM

2012-01-01

Current source inverter (CSI) fed drives are employed in high power applications. The conventional CSI drives suffer from drawbacks such as harmonic resonance, unstable operation at low speed ranges, and torque pulsation. CSI fed drives with Direct Torque Control (DTC) has drawn the attention of the motor drives designers because its implementation requires no position sensor. Crucial to the success of this scheme is the estimation of electromagnetic torque and stator flux linkages using the ...

Environmental Disclosure of Electric Power Companies Listed in the Corporate Sustainability Index (CSI

Directory of Open Access Journals (Sweden)

Clésia Ana Gubiani

2012-12-01

Full Text Available The study aimed to verify the level of disclosure of environmental information in the administration reports of the energy companies listed in the Corporate Sustainability Index (CSI. A descriptive and quantitative research was done, using the content analysis technique on the administration reports from 2006 to 2008. The sample consisted of 11 electric power companies listed in the CSI. For quantitative analysis of the disclosure index, the data collection instrument was based on the study of Rover, Murcia and Borba (2008, which proposes eight environmental categories and 36 subcategories. For the whole analysis of the data were elaborated networks of the items disclosed in each company, using the software UNICET ®. The survey results showed that there is satisfactory disclosure in the categories of environmental policies and education, training and research environment. However, it was found that there is need for greater disclosure of categories of products impacts and processes in the environment, power polices and financial environmental information. It was concluded that the information disclosed in the administration reports of the companies surveyed about the environmental information do not respect the principle of full disclosure.

To Think and Watch the Evil: The Turn of the Screw as Cultural Reference in Television from Dark Shadows to C.S.I.

Directory of Open Access Journals (Sweden)

Anna Viola Sborgi

2012-07-01

Full Text Available Since its first publication, Henry James’s The Turn of the Screw (1898 has always haunted the imagination of artists (Benjamin Britten, Jack Clayton, Amenábar and has been widely used as a source for television narratives (Dan Curtis, US TV version starring Colin Firth, Tim Fywell. In serial productions, James’s story has been the object of extensive quotation and allusion, from the 1960 gothic soap opera Dark Shadows to the C.S.I. episode Turn of the Screw (Season 4, Episode 21. A milestone in literary history, the story now embodies a set of cultural references conveying different, complex meanings, which can only be disclosed in the light of contemporary forms of representing reality. The novella appeals to two apparently opposite tendencies in contemporary television: the morbid display of the real (C.S.I. and the quest for the supernatural (Buffy The Vampire Slayer, among others. A line can be traced from Dark Shadows, the show that pioneered the genre, to contemporary horror soaps about vampires and supernatural phenomena. This paper shows the ways in which James’ sophisticated novella makes its way through popular culture, and how its constant ambiguous, dilemmatic interplay between reality and imagination can be related to the double-sided drive of the contemporary public towards hyper-reality and the supernatural.

Use of the Central Sensitization Inventory (CSI) as a treatment outcome measure for patients with chronic spinal pain disorder in a functional restoration program.

Science.gov (United States)

Neblett, Randy; Hartzell, Meredith M; Williams, Mark; Bevers, Kelley R; Mayer, Tom G; Gatchel, Robert J

2017-12-01

The Central Sensitization Inventory (CSI) is a valid and reliable patient-reported instrument designed to identify patients whose presenting symptoms may be related to central sensitization (CS). Part A of the CSI measures a full array of 25 somatic and emotional symptoms associated with CS, and Part B asks if patients have previously been diagnosed with one or more specific central sensitivity syndromes (CSSs) and related disorders. The CSI has previously been validated in a group of patients with chronic pain who were screened by a trained psychiatrist for specific CSS diagnoses. It is currently unknown if the CSI can be a useful treatment-outcome assessment tool for patients with chronic spinal pain disorder (CSPD) who are not screened for comorbid CSSs. It is known, however, that previous studies have identified CS-related symptoms, and comorbid CSSs, in subsets of patients with CSPDs. Studies have also shown that CS-related symptoms can be influenced by cognitive and psychosocial factors, including abuse history in both childhood and adulthood, sleep disturbance, catastrophic and fear-avoidant cognitions, and symptoms of depression and anxiety. This study aimed to evaluate CSI scores, and their associations with other clinically relevant psychosocial variables, in a cohort of patients with CSPD who entered and completed a functional restoration program. A retrospective study of prospectively collected data from a cohort study of patients with CSPD, who completed the CSI at admission to, and discharge from, an interdisciplinary function restoration program (FRP) was carried out. A cohort of 763 patients with CSPD comprised the study sample. Clinical interviews evaluated mood disorders and abuse history. A series of self-reported measures evaluated comorbid psychosocial symptoms, including pain intensity, pain-related anxiety, depressive symptoms, somatization symptoms, perceived disability, and sleep disturbance, at FRP admission and discharge. Patients were

Temporal resolution limit estimation of x-ray streak cameras using a CsI photocathode

Energy Technology Data Exchange (ETDEWEB)

Li, Xiang; Gu, Li; Zong, Fangke; Zhang, Jingjin; Yang, Qinlao, E-mail: qlyang@szu.edu.cn [Key Laboratory of Optoelectronic Devices and Systems of Ministry of Education and Guangdong Province, Institute of Optoelectronics, Shenzhen University, Shenzhen 518060 (China)

2015-08-28

A Monte Carlo model is developed and implemented to calculate the characteristics of x-ray induced secondary electron (SE) emission from a CsI photocathode used in an x-ray streak camera. Time distributions of emitted SEs are investigated with an incident x-ray energy range from 1 to 30 keV and a CsI thickness range from 100 to 1000 nm. Simulation results indicate that SE time distribution curves have little dependence on the incident x-ray energy and CsI thickness. The calculated time dispersion within the CsI photocathode is about 70 fs, which should be the temporal resolution limit of x-ray streak cameras that use CsI as the photocathode material.

Enhanced quantum efficiency for CsI grown on a graphite-based substrate coating

CERN Document Server

Friese, J; Homolka, J; Kastenmüller, A; Maier-Komor, P; Peter, M; Zeitelhack, K; Kienle, P; Körner, H J

1999-01-01

Quantum efficiencies (QE) in the vacuum ultraviolet (VUV) wavelength region have been measured for solid CsI layers on various substrates. The CsI films were deposited applying electron beam evaporation. The QE measurements were performed utilizing synchrotron radiation as well as light from a deuterium lamp. A GaAsP diode with a sensitivity calibration traceable to a primary radiation standard was used for normalization. For CsI layers grown on resin-stabilized graphite films a significant enhancement of QE was observed. Substrates suitable for gas detector applications and aging properties were investigated. The procedures to prepare and reproduce high quantum efficient CsI layers are described.

Development Status and Performance Comparisons of Environmental Barrier Coating Systems for SiCSiC Ceramic Matrix Composites

Science.gov (United States)

Zhu, Dongming; Harder, Bryan

2016-01-01

Environmental barrier coatings (EBC) and SiCSiC ceramic matrix composites (CMCs) will play a crucial role in future aircraft turbine engine systems, because of their ability to significantly increase engine operating temperatures, reduce engine weight and cooling requirements. This paper presents current NASA EBC-CMC development emphases including: the coating composition and processing improvements, laser high heat flux-thermal gradient thermo-mechanical fatigue - environmental testing methodology development, and property evaluations for next generation EBC-CMC systems. EBCs processed with various deposition techniques including Plasma Spray, Electron Beam - Physical Vapor Deposition, and Plasma Spray Physical Vapor Deposition (PS-PVD) will be particularly discussed. The testing results and demonstrations of advanced EBCs-CMCs in complex simulated engine thermal gradient cyclic fatigue, oxidizing-steam and CMAS environments will help provide insights into the coating development strategies to meet long-term engine component durability goals.

SU-E-I-51: Quantitative Assessment of X-Ray Imaging Detector Performance in a Clinical Setting - a Simple Approach Using a Commercial Instrument

Energy Technology Data Exchange (ETDEWEB)

Sjoeberg, J; Bujila, R; Omar, A; Nowik, P; Mobini-Kesheh, S; Lindstroem, J [Karolinska University Hospital, Solna (Sweden)

2015-06-15

Purpose: To measure and compare the performance of X-ray imaging detectors in a clinical setting using a dedicated instrument for the quantitative determination of detector performance. Methods: The DQEPro (DQE Instruments Inc., London, Ontario Canada) was used to determine the MTF, NPS and DQE using an IEC compliant methodology for three different imaging modalities: conventional radiography (CsI-based detector), general-purpose radioscopy (CsI-based detector), and mammography (a-Se based detector). The radiation qualities (IEC) RQA-5 and RQA-M-2 were used for the CsI-based and a-Se-based detectors, respectively. The DQEPro alleviates some of the difficulties associated with DQE measurements by automatically positioning test devices over the detector, guiding the user through the image acquisition process and providing software for calculations. Results: A comparison of the NPS showed that the image noise of the a-Se detector was less correlated than the CsI detectors. A consistently higher performance was observed for the a-Se detector at all spatial frequencies (MTF: 0.97@0.25 cy/mm, DQE: 0.72@0.25 cy/mm) and the DQE drops off slower than for the CsI detectors. The CsI detector used for conventional radiography displayed a higher performance at low spatial frequencies compared to the CsI detector used for radioscopy (DQE: 0.65 vs 0.60@0.25 cy/mm). However, at spatial frequencies above 1.3 cy/mm, the radioscopy detector displayed better performance than the conventional radiography detector (DQE: 0.35 vs 0.24@2.00 cy/mm). Conclusion: The difference in the MTF, NPS and DQE that was observed for the two different CsI detectors and the a-Se detector reflect the imaging tasks that the different detector types are intended for. The DQEPro has made the determination and calculation of quantitative metrics of X-ray imaging detector performance substantially more convenient and accessible to undertake in a clinical setting.

Validation of the Mexican Spanish version of the EORTC QLQ-H&N35 instrument to measure health-related quality of life in patients with head and neck cancers.

Science.gov (United States)

Carrillo, José F; Ortiz-Toledo, Miguel Angel; Salido-Noriega, Zarahi; Romero-Ventura, Norma Berenice; Ochoa-Carrillo, Francisco J; Oñate-Ocaña, Luis F

2013-05-01

Health-related quality of life (HRQL) is an important outcome measurement in oncology. Our aim was to validate the Mexican Spanish version of the European Organisation for Research and Treatment of Cancer (EORTC) QLQ-H&N35 questionnaire to measure HRQL in patients with head and neck cancers. The QLQ-C30 and QLQ-H&N35 instruments were applied to Mexican patients with head and neck cancer at a cancer referral center. Reliability and validity tests were performed. Test-retest was carried out in selected patients. One hundred ninety-three patients were included in this cohort; tumor locations included the following: oral cavity 45 (23.3 %); larynx 35 (18.1 %); thyroid carcinoma invasive to aerodigestive tract 32 (16.6 %); oropharynx 17 (8.8 %); hypopharynx 12 (6.2 %); nasal cavity and paranasal sinuses 11 (5.7 %); salivary glands 11 (5.7 %); nasopharynx 8 (4.1 %); eye and adnexa 7 (3.6 %); cervical metastases of unknown origin 5 (2.6 %); primary sarcoma of the head and neck region 5 (2.6 %); maxillary antrum carcinoma 4 (2.1 %); and retinoblastoma 1 (0.5 %). Questionnaire compliance rates were high, and the instrument was well accepted; the internal consistency tests demonstrated good convergent and divergent validity. Cronbach's α coefficients of 8 of 9 multi-item scales of the QLQ-C30 and 6 of 8 scales of the QLQ-H&N35 instruments were >0.7 (range 0.22-0.89). Scales of the QLQ-C30 and QLQ-H&N35 instruments distinguished among clinically distinct groups of patients; some were highly sensitive to change over time. The Mexican Spanish version of the QLQ-H&N35 questionnaire is reliable and valid for the assessment of HRQL in patients with head and neck cancers and can be used in clinical trials in Mexican communities.

Decay-time measurements on 'pure' CsI scintillators prepared by different methods

International Nuclear Information System (INIS)

Keszthelyi-Landori, S.; Foeldvari, I.; Voszka, R.; Fodor, Z.; Seres, Z.

1990-05-01

The discovery of the fast decay time of the pure CsI and the various results of the measured samples led to the investigation of decay time of CsI crystals prepared by different methods. Carefully grown or prepared pure CsI behaves as fast scintillators with well or totally suppressed slow decay component. The estimated fast/slow or fast/total ratio is related to the preparation method and to the remaining built-in contamination of the samples. The fast decay of pure CsI consists of two components with decay times of ≅1 and ≅10 ns - with an intensity ratio of 0.3 and 0.65 for gamma and for alpha radiation, respectively. This new ≅1 ns component and the ≅0.8 fast/total ratio may achieve an important role in many applications where fast timing properties are needed, substituting BaF 2 . (author) 18 refs.; 8 figs.; 3 tabs

Preparation of reflective CsI photocathodes with reproducible high quantum efficiency

Science.gov (United States)

Maier-Komor, P.; Bauer, B. B.; Friese, J.; Gernhäuser, R.; Kienle, P.; Körner, H. J.; Montermann, G.; Zeitelhack, K.

1995-02-01

CsI as a solid UV-photocathode material has many promising applications in fast gaseous photon detectors. They are proposed in large area Ring Imaging CHerenkov (RICH) devices in forthcoming experiments at various high-energy particle accelerators. A high photon-to-electron conversion efficiency is a basic requirement for the successful operation of these devices. High reproducible quantum efficiencies could be achieved with CsI layers prepared by electron beam evaporation from a water-cooled copper crucible. CsI films were deposited in the thickness range of 30 to 500 μg/cm 2. Absorption coefficients and quantum efficiencies were measured in the wavelength region of 150 nm to 250 nm. The influence of various evaporation parameters on the quantum efficiency were investigated.

Preparation of reflective CsI photocathodes with reproducible high quantum efficiency

Energy Technology Data Exchange (ETDEWEB)

Maier-Komor, P. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Bauer, B.B. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Friese, J. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Gernhaeuser, R. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Kienle, P. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Koerner, H.J. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Montermann, G. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Zeitelhack, K. [Technische Univ. Muenchen, Garching (Germany). Physik-Department

1995-08-01

CsI as a solid UV-photocathode material has many promising applications in fast gaseous photon detectors. They are proposed in large area Ring Imaging CHerenkov (RICH) devices in forthcoming experiments at various high-energy particle accelerators. A high photon-to-electron conversion efficiency is a basic requirement for the successful operation of these devices. High reproducible quantum efficiencies could be achieved with CsI layers prepared by electron beam evaporation from a water-cooled copper crucible. CsI films were deposited in the thickness range of 30 to 500 {mu}g/cm{sup 2}. Absorption coefficients and quantum efficiencies were measured in the wavelength region of 150 nm to 250 nm. The influence of various evaporation parameters on the quantum efficiency were investigated. (orig.).

Counter support for WA35

CERN Multimedia

CERN PhotoLab

1977-01-01

This assembly was equipped with 78 counters, each consisting of a lucite cone, to produce Cerenkov light, and a CsI scintillator plate of 3 mm thickness glued on the face of the cone. The experiment WA35 was set-up in the s1 beam (West Hall) by the Darmstadt-Heidelberg-Virginia-Warsaw Collaboration to measure angular distributions and multiplicities of pions and recoil protons produced by hadrons interacting in nuclei. (See Annual Report 1976 p. 39)

CSI-EPT in Presence of RF-Shield for MR-Coils.

Science.gov (United States)

Arduino, Alessandro; Zilberti, Luca; Chiampi, Mario; Bottauscio, Oriano

2017-07-01

Contrast source inversion electric properties tomography (CSI-EPT) is a recently developed technique for the electric properties tomography that recovers the electric properties distribution starting from measurements performed by magnetic resonance imaging scanners. This method is an optimal control approach based on the contrast source inversion technique, which distinguishes itself from other electric properties tomography techniques for its capability to recover also the local specific absorption rate distribution, essential for online dosimetry. Up to now, CSI-EPT has only been described in terms of integral equations, limiting its applicability to homogeneous unbounded background. In order to extend the method to the presence of a shield in the domain-as in the recurring case of shielded radio frequency coils-a more general formulation of CSI-EPT, based on a functional viewpoint, is introduced here. Two different implementations of CSI-EPT are proposed for a 2-D transverse magnetic model problem, one dealing with an unbounded domain and one considering the presence of a perfectly conductive shield. The two implementations are applied on the same virtual measurements obtained by numerically simulating a shielded radio frequency coil. The results are compared in terms of both electric properties recovery and local specific absorption rate estimate, in order to investigate the requirement of an accurate modeling of the underlying physical problem.

Excellent c-Si surface passivation by thermal atomic layer deposited aluminum oxide after industrial firing activation

International Nuclear Information System (INIS)

Liao, B; Stangl, R; Ma, F; Mueller, T; Lin, F; Aberle, A G; Bhatia, C S; Hoex, B

2013-01-01

We demonstrate that by using a water (H 2 O)-based thermal atomic layer deposited (ALD) aluminum oxide (Al 2 O 3 ) film, excellent surface passivation can be attained on planar low-resistivity silicon wafers. Effective carrier lifetime values of up to 12 ms and surface recombination velocities as low as 0.33 cm s −1 are achieved on float-zone wafers after a post-deposition thermal activation of the Al 2 O 3 passivation layer. This post-deposition activation is achieved using an industrial high-temperature firing process which is commonly used for contact formation of standard screen-printed silicon solar cells. Neither a low-temperature post-deposition anneal nor a silicon nitride capping layer is required in this case. Deposition temperatures in the 100–400 °C range and peak firing temperatures of about 800 °C (set temperature) are investigated. Photoluminescence imaging shows that the surface passivation is laterally uniform. Corona charging and capacitance–voltage measurements reveal that the negative fixed charge density near the AlO x /c-Si interface increases from 1.4 × 10 12 to 3.3 × 10 12 cm −2 due to firing, while the midgap interface defect density reduces from 3.3 × 10 11 to 0.8 × 10 11 cm −2 eV −1 . This work demonstrates that direct firing activation of thermal ALD Al 2 O 3 is feasible, which could be beneficial for solar cell manufacturing. (paper)

Properties of CsI and CsI-TMAE photocathodes

International Nuclear Information System (INIS)

Anderson, D.F.; Kwan, S.; Peskov, V.; Hoeneisen, B.

1992-06-01

The importance of heating the CsI or CsI-TMAE photocathodes during preparation, as well as the importance of the gas environment on the quantum efficiency is presented. The dependence of the aging characteristics of these photocathodes on the operating temperature, on the presence of gas, and on the charge amplification of the chamber is also discussed. For CsI photocathodes charges in excess of 2x10 14 e - /mm 2 can be collected with little degradation of performance. A timing resolution of 0.55 ns is also achieved for single photoelectrons suggesting a possible time-of-flight detector

Construction of C35 gene bait recombinants and T47D cell cDNA library.

Science.gov (United States)

Yin, Kun; Xu, Chao; Zhao, Gui-Hua; Liu, Ye; Xiao, Ting; Zhu, Song; Yan, Ge

2017-11-20

C35 is a novel tumor biomarker associated with metastasis progression. To investigate the interaction factors of C35 in its high expressed breast cancer cell lines, we constructed bait recombinant plasmids of C35 gene and T47D cell cDNA library for yeast two-hybrid screening. Full length C35 sequences were subcloned using RT-PCR from cDNA template extracted from T47D cells. Based on functional domain analysis, the full-length C35 1-348bp was also truncated into two fragments C351-153bp and C35154-348bp to avoid auto-activation. The three kinds of C35 genes were successfully amplified and inserted into pGBKT7 to construct bait recombinant plasmids pGBKT7-C351-348bp, pGBKT7-C351-153bp and pGBKT7-C35154-348bp, then transformed into Y187 yeast cells by the lithium acetate method. Auto-activation and toxicity of C35 baits were detected using nutritional deficient medium and X-α-Gal assays. The T47D cell ds cDNA was generated by SMART TM technology and the library was constructed using in vivo recombination-mediated cloning in the AH109 yeast strain using a pGADT7-Rec plasmid. The transformed Y187/pGBKT7-C351-348bp line was intensively inhibited while the truncated Y187/pGBKT7-C35 lines had no auto-activation and toxicity in yeast cells. The titer of established cDNA library was 2 × 10 7 pfu/mL with high transformation efficiency of 1.4 × 10 6 , and the insert size of ds cDNA was distributed homogeneously between 0.5-2.0 kb. Our research generated a T47D cell cDNA library with high titer, and the constructed two C35 "baits" contained a respective functional immunoreceptor tyrosine based activation motif (ITAM) and the conserved last four amino acids Cys-Ile-Leu-Val (CILV) motif, and therefore laid a foundation for screening the C35 interaction factors in a BC cell line.

Instruments for assessing the burden of informal caregiving for stroke patients in clinical practice: a comparison of CSI, CRA, SCQ and self-rated burden

NARCIS (Netherlands)

van Exel, N. Job A.; Scholte op Reimer, Wilma J. M.; Brouwer, Werner B. F.; van den Berg, Bernard; Koopmanschap, Marc A.; van den Bos, Geertrudis A. M.

2004-01-01

Objective: To compare the feasibility, convergent and clinical validity of three commonly used burden scales: Caregiver Strain Index (CSI), Caregiver Reaction Assessment (CRA) and Sense of Competence Questionnaire (SCQ), with a self-developed single question on self-rated burden (SRB). Subjects:

Experimental study on the CsI (Tl) crystal anti-compton detector in CDEX

International Nuclear Information System (INIS)

Liu Shukui; Yue Qian; Tang Changjian

2012-01-01

CDEX (China Dark matter Experiment) Collaboration will carry out direct search for dark matter with Ultra-Low Energy Threshold High Purity germanium (ULE-HPGe) detector at CJPL (China Jinping deep underground Laboratory). Before underground research, some experiments of the CsI (Tl) crystal Anti-Compton detector have been done on the ground, including light guide choice, wrapping material choice, height uniformity of CsI (Tl) crystal, side uniformity of CsI (Tl) crystal and the test results of all the crystals. Through the preliminary work on the ground, we have got some knowledge of the anti-compton detector and prepared for the underground experiment. (authors)

Analyses of CsI aerosol deposition tests in WIND project with ART and VICTORIA codes

International Nuclear Information System (INIS)

Yuchi, Y.; Shibazaki, H.; Kudo, T.

2000-01-01

Deposition behavior of cesium iodide (CsI) was analyzed with ART and VICTORIA-92 codes for a test of the aerosol re-vaporization test series performed in WIND project at JAERI. In the test analyzed, CsI aerosol was injected into piping of test section where metaboric acid (HBO 2 ) was placed in advance on the floor area. It was confirmed in the present analysis that similar results on the CsI deposition were obtained between ART and VICTORIA when influences of chemical interactions were negligibly small. The analysis with VICTORIA agreed satisfactorily with the test results in analytical cases that cesium metaborate (CsBO 2 ) was injected into the test section instead of CsI to simulate the pre-existence of HBO 2 effect. (author)

Visualization of a City Sustainability Index (CSI: Towards Transdisciplinary Approaches Involving Multiple Stakeholders

Directory of Open Access Journals (Sweden)

Koichiro Mori

2015-09-01

Full Text Available We have developed a visualized 3-D model of a City Sustainability Index (CSI based on our original concept of city sustainability in which a sustainable city is defined as one that maximizes socio-economic benefits while meeting constraint conditions of the environment and socio-economic equity on a permanent basis. The CSI is based on constraint and maximization indicators. Constraint indicators assess whether a city meets the necessary minimum conditions for city sustainability. Maximization indicators measure the benefits that a city generates in socio-economic aspects. When used in the policy-making process, the choice of constraint indicators should be implemented using a top-down approach. In contrast, a bottom-up approach is more suitable for defining maximization indicators because this technique involves multiple stakeholders (in a transdisciplinary approach. Using different materials of various colors, shapes, sizes, we designed and constructed the visualized physical model of the CSI to help people evaluate and compare the performance of different cities in terms of sustainability. The visualized model of the CSI can convey complicated information in a simple and straightforward manner to diverse stakeholders so that the sustainability analysis can be understood intuitively by ordinary citizens as well as experts. Thus, the CSI model helps stakeholders to develop critical thinking about city sustainability and enables policymakers to make informed decisions for sustainability through a transdisciplinary approach.

From 1 Sun to 10 Suns c-Si Cells by Optimizing Metal Grid, Metal Resistance, and Junction Depth

International Nuclear Information System (INIS)

Chaudhari, V.A.; Solanki, C.S.

2009-01-01

Use of a solar cell in concentrator PV technology requires reduction in its series resistance in order to minimize the resistive power losses. The present paper discusses a methodology of reducing the series resistance of a commercial c-Si solar cell for concentrator applications, in the range of 2 to 10 suns. Step by step optimization of commercial cell in terms of grid geometry, junction depth, and electroplating of the front metal contacts is proposed. A model of resistance network of solar cell is developed and used for the optimization. Efficiency of un optimized commercial cell at 10 suns drops by 30% of its 1 sun value corresponding to resistive power loss of about 42%. The optimized cell with grid optimization, junction optimization, electroplating, and junction optimized with electroplated contacts cell gives resistive power loss of 20%, 16%, 11%, and 8%, respectively. An efficiency gain of 3% at 10 suns for fully optimized cell is estimated

Adsorption and revaporisation studies of thin iodine oxide and CsI aerosol deposits from containment surface materials in LWRs

Energy Technology Data Exchange (ETDEWEB)

Tietze, S.; Foreman, M.; Ekberg, C. [Chalmers Univ. of Technology, Goeteborg (Sweden); Kaerkelae, T.; Auvinen, A.; Tapper, U.; Jokiniemi, J. [VTT Technical Research Centre of Finland, Espoo (Finland)

2013-07-15

During a severe nuclear accident released fission and radiolysis products can react with each other to form new species which might contribute to the volatile source term. Iodine will be released from UO2 fuel mainly in form as CsI aerosol particles and elemental iodine. Elemental iodine can react in gaseous phase with ozone to form solid iodine oxide aerosol particles (IOx). Within the AIAS-2 (Adsorption of Iodine Aerosols on Surfaces) project the interactions of IOx and CsI aerosols with common containment surface materials was investigated. Common surface materials in Swedish and Finnish LWRs are Teknopox Aqua V A paint films and metal surfaces such as Cu, Zn, Al and SS. Non-radioactive and {sup 131}I labelled aerosols were produced from a KI solution and ozone with a new facility designed and built at VTT Technical Research Centre of Finland. CsI aerosols were produced from a CsI solution with the same facility. A monolayer of the aerosols was deposited on the surfaces. The deposits were analysed with microscopic and spectroscopic measurement techniques to identify the chemical form of the deposits on the surfaces to identify if a chemical conversion on the different surface materials had occured. The revaporisation behaviour of the deposited aerosol particles from the different surface materials was studied under the influence of heat, humidity and gamma irradiation at Chalmers University of Technology, Sweden. Studies on the effects of humidity were performed using the FOMICAG facility, while heat and irradiation experiments were performed in a thermostated heating block and with a gammacell 22 with a dose rate of 14 kGy/h. The revaporisation losses were measured using a HPGe detector. The decomposition effect of the radiolysis product carbon monoxide was tested on IOx aerosols deposited on a glass fibre filter. Iodine oxide particles were produced at 50 deg. C, 100 deg. C and 120 deg. C and deposited on filter samples in order to study the chemical

Adsorption and revaporisation studies of thin iodine oxide and CsI aerosol deposits from containment surface materials in LWRs

International Nuclear Information System (INIS)

Tietze, S.; Foreman, M.; Ekberg, C.; Kaerkelae, T.; Auvinen, A.; Tapper, U.; Jokiniemi, J.

2013-07-01

During a severe nuclear accident released fission and radiolysis products can react with each other to form new species which might contribute to the volatile source term. Iodine will be released from UO2 fuel mainly in form as CsI aerosol particles and elemental iodine. Elemental iodine can react in gaseous phase with ozone to form solid iodine oxide aerosol particles (IOx). Within the AIAS-2 (Adsorption of Iodine Aerosols on Surfaces) project the interactions of IOx and CsI aerosols with common containment surface materials was investigated. Common surface materials in Swedish and Finnish LWRs are Teknopox Aqua V A paint films and metal surfaces such as Cu, Zn, Al and SS. Non-radioactive and 131 I labelled aerosols were produced from a KI solution and ozone with a new facility designed and built at VTT Technical Research Centre of Finland. CsI aerosols were produced from a CsI solution with the same facility. A monolayer of the aerosols was deposited on the surfaces. The deposits were analysed with microscopic and spectroscopic measurement techniques to identify the chemical form of the deposits on the surfaces to identify if a chemical conversion on the different surface materials had occured. The revaporisation behaviour of the deposited aerosol particles from the different surface materials was studied under the influence of heat, humidity and gamma irradiation at Chalmers University of Technology, Sweden. Studies on the effects of humidity were performed using the FOMICAG facility, while heat and irradiation experiments were performed in a thermostated heating block and with a gammacell 22 with a dose rate of 14 kGy/h. The revaporisation losses were measured using a HPGe detector. The decomposition effect of the radiolysis product carbon monoxide was tested on IOx aerosols deposited on a glass fibre filter. Iodine oxide particles were produced at 50 deg. C, 100 deg. C and 120 deg. C and deposited on filter samples in order to study the chemical speciation of

Fast and accurate methods for the performance testing of highly-efficient c-Si photovoltaic modules using a 10 ms single-pulse solar simulator and customized voltage profiles

International Nuclear Information System (INIS)

Virtuani, A; Rigamonti, G; Friesen, G; Chianese, D; Beljean, P

2012-01-01

Performance testing of highly efficient, highly capacitive c-Si modules with pulsed solar simulators requires particular care. These devices in fact usually require a steady-state solar simulator or pulse durations longer than 100–200 ms in order to avoid measurement artifacts. The aim of this work was to validate an alternative method for the testing of highly capacitive c-Si modules using a 10 ms single pulse solar simulator. Our approach attempts to reconstruct a quasi-steady-state I–V (current–voltage) curve of a highly capacitive device during one single 10 ms flash by applying customized voltage profiles–-in place of a conventional V ramp—to the terminals of the device under test. The most promising results were obtained by using V profiles which we name ‘dragon-back’ (DB) profiles. When compared to the reference I–V measurement (obtained by using a multi-flash approach with approximately 20 flashes), the DB V profile method provides excellent results with differences in the estimation of P max (as well as of I sc , V oc and FF) below ±0.5%. For the testing of highly capacitive devices the method is accurate, fast (two flashes—possibly one—required), cost-effective and has proven its validity with several technologies making it particularly interesting for in-line testing. (paper)

Secrecy performance analysis of SIMO underlay cognitive radio systems with outdated CSI

KAUST Repository

Lei, Hongjiang; Zhang, Jianming; Park, Kihong; Ansari, Imran Shafique; Pan, Gaofeng; Alouini, Mohamed-Slim

2017-01-01

This study investigates the secrecy outage performance of a single-input multiple-output underlay cognitive radio network (CRN) with outdated channel state information (CSI). The confidential messages are transmitted from transmitter to the destination, while a multi-antenna eavesdropper exists. The maximal ratio combining and selection combining schemes are utilised at the receivers to improve the quality of the received signal-to-noise ratio. The exact and asymptotic closed-form expressions of secrecy outage probability are derived, and simulation results are provided to verify the authors' proposed analytical results. The results reveal that imperfect CSI of main channels deteriorates the secrecy outage performance while that of eavesdropping and interfering channels has contrary effect, and only a unity diversity order can be obtained in underlay CRNs with imperfect CSI.

Secrecy performance analysis of SIMO underlay cognitive radio systems with outdated CSI

KAUST Repository

Lei, Hongjiang

2017-06-13

This study investigates the secrecy outage performance of a single-input multiple-output underlay cognitive radio network (CRN) with outdated channel state information (CSI). The confidential messages are transmitted from transmitter to the destination, while a multi-antenna eavesdropper exists. The maximal ratio combining and selection combining schemes are utilised at the receivers to improve the quality of the received signal-to-noise ratio. The exact and asymptotic closed-form expressions of secrecy outage probability are derived, and simulation results are provided to verify the authors\\' proposed analytical results. The results reveal that imperfect CSI of main channels deteriorates the secrecy outage performance while that of eavesdropping and interfering channels has contrary effect, and only a unity diversity order can be obtained in underlay CRNs with imperfect CSI.

Performance Analysis of Communications under Energy Harvesting Constraints with noisy CSI

KAUST Repository

Znaidi, Mohamed Ridha Ali

2016-01-06

In energy harvesting communications, the transmitters have to adapt transmission to availability of energy harvested during the course of communication. The performance of the transmission depends on the channel conditions which vary randomly due to environmental changes. In this work, we consider the problem of power allocation taking into account the energy arrivals over time and the degree of channel state information (CSI) available at the transmitter, to maximize the throughput. Differently from previous work, the CSI at the transmitter is not perfect and may include estimation errors. We solve this problem with respect to the Energy Harvesting constraints. We determine the optimal power in the case where the channel is assumed to be perfectly known at the receiver. Also, we obtain the power policy when the transmitter has no CSI. Furthermore, we analyze the asymptotic average throughput in a system where the average recharge rate goes asymptotically to zero and when it is very high.

Deposition of CsI aerosol in horizontal straight pipes in WIND project

International Nuclear Information System (INIS)

Sugimoto, J.; Maruyama, Y.; Igarashi, M.; Hidaka, A.; Maeda, A.; Harada, Y.; Hashimoto, K.

1996-01-01

In the WIND Project at Japan Atomic Energy Research Institute, the aerosol behaviors such as deposition, revaporization and resuspension have been investigated under the severe accident conditions. The present paper describes the deposition of CsI aerosol in horizontal straight pipes. The test results showed that the aerosol deposition depended on thermo-fluid dynamic characteristics of the carrier gas. In the test with the temperature gradient of the pipe, the deposition of CsI was remarkable within the downstream side, where the temperature of the gas was higher than that of the pipe wall. It is thus supposed that the major mechanism of the deposition was thermophoresis caused by the temperature gradient within the gas phase. However, circumferential distribution of the deposited CsI was influenced by the argon flow rate. In laminar flow case, larger amount of CsI was deposited on the ceiling than the floor area. Three-dimensional thermo-fluid dynamic analysis suggested that much sharper radial temperature gradient was developed within the gas near the ceiling area due to the formation of a natural convective secondary flow. This could result in the promotion of the thermophoretic aerosol deposition. On the other hand, slight circumferential distribution was observed in case of the high flow rate, probably due to a uniform temperature field. It was also found that the close coupling of the FP behavior and the detailed thermohydraulic analyses is essential in order to accurately predict the CsI deposition in the pipe. The findings on aerosol behaviors will also be utilized for the evaluation of sodium aerosol behaviors of fast reactors. (author)

Effect of hydrogen on passivation quality of SiNx/Si-rich SiNx stacked layers deposited by catalytic chemical vapor deposition on c-Si wafers

International Nuclear Information System (INIS)

Thi, Trinh Cham; Koyama, Koichi; Ohdaira, Keisuke; Matsumura, Hideki

2015-01-01

We investigate the role of hydrogen content and fixed charges of catalytic chemical vapor deposited (Cat-CVD) SiN x /Si-rich SiN x stacked layers on the quality of crystalline silicon (c-Si) surface passivation. Calculated density of fixed charges is on the order of 10 12 cm −2 , which is high enough for effective field effect passivation. Hydrogen content in the films is also found to contribute significantly to improvement in passivation quality of the stacked layers. Furthermore, Si-rich SiN x films deposited with H 2 dilution show better passivation quality of SiN x /Si-rich SiN x stacked layers than those prepared without H 2 dilution. Effective minority carrier lifetime (τ eff ) in c-Si passivated by SiN x /Si-rich SiN x stacked layers is as high as 5.1 ms when H 2 is added during Si-rich SiN x deposition, which is much higher than the case of using Si-rich SiN x films prepared without H 2 dilution showing τ eff of 3.3 ms. - Highlights: • Passivation mechanism of Si-rich SiN x /SiN x stacked layers is investigated. • H atoms play important role in passivation quality of the stacked layer. • Addition of H 2 gas during Si-rich SiN x film deposition greatly enhances effective minority carrier lifetime (τ eff ). • For a Si-rich SiN x film with refractive index of 2.92, τ eff improves from 3.3 to 5.1 ms by H 2 addition

Distributed cognitive two-way relay beamformer designs under perfect and imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla

2011-09-01

In this paper, we present distributed two-way relay beamformer designs for a cognitive radio network (CRN) in which a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relay nodes. The secondary nodes share the spectrum with a licensed primary user (PU) node, and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. First, we consider relay beamformer designs assuming the availability of perfect channel state information (CSI). For this case, a mean-square error (MSE)-constrained beamformer that minimizes the total relay transmit power, and an MSE-balancing beamformer with a constraint on the total relay transmit power are proposed. Next, we consider relay beamformer designs assuming that the available CSI is imperfect. For this case too, we consider the same problems as those in the case of perfect CSI, and propose beamformer designs that are robust to the errors in the CSI. We show that the proposed designs can be reformulated as convex optimization problems that can be solved efficiently. Through numerical simulations, we illustrate the performance of the proposed designs. © 2011 IEEE.

Fission product behavior in high-temperature water: CsI vs MoO4

Science.gov (United States)

Kanjana, K.; Silva, K.; Channuie, J.

2017-09-01

Fission product behaviors of Cs, a major element released in a severe nuclear accident, still remain unclear. The question frequently addressed is whether Cs released will be in the form of Cs2MoO4 or CsOH. This is a challenging issue since it has been demonstrated that the reaction between Cs2MoO4 and water leading to CsOH production is thermodynamically favored. The present research aims at investigation of CsOH generation through this chemical channel. A high-temperature setup with a flow system based on the cooling system of a water-cooled nuclear reactor has been assembled. The reaction between aqueous solutions of CsI and Na2MoO4 in a high-corrosion-resistant hot cell (Hastelloy) has been studied up to 80 °C in deoxygenated system. The products have been characterized using FTIR and XRD. The results have shown that there is no reaction between CsI and Na2MoO4 under the experimental conditions.

Acinetobacter calcoaceticus CSY-P13 Mitigates Stress of Ferulic and p-Hydroxybenzoic Acids in Cucumber by Affecting Antioxidant Enzyme Activity and Soil Bacterial Community

Directory of Open Access Journals (Sweden)

Fenghui Wu

2018-06-01

Full Text Available Ferulic acid (FA and p-hydroxybenzoic acid (PHBA are main phenolic compounds accumulated in rhizosphere of continuously cropped cucumber, causing stress in plants. Microbial degradation of a mixture of FA and PHBA is not well understood in soil. We isolated a strain CSY-P13 of Acinetobacter calcoaceticus, inoculated it into soil to protect cucumber from FA and PHBA stress, and explored a mechanism underlying the protection. CSY-P13 effectively degraded a mixture of FA and PHBA in culture solution under conditions of 39.37°C, pH 6.97, and 21.59 g L-1 potassium dihydrogen phosphate, giving rise to 4-vinyl guaiacol, vanillin, vanillic acid, and protocatechuic acid. During FA and PHBA degradation, activities of superoxide dismutase (SOD, catalase, ascorbate peroxidase, and dehydroascorbate reductase in CSY-P13 were induced. Inoculated into cucumber-planted soil containing 220 μg g-1 mixture of FA and PHBA, CSY-P13 degraded FA and PHBA in soil, increased plant height, and decreased malonaldehyde, superoxide radical, and hydrogen peroxide levels in leaves. CSY-P13 also enhanced SOD, guaiacol peroxidase, catalase, glutathione peroxidase, ascorbate peroxidase, monodehydroascorbate reductase, dehydroascorbate reductase, and glutathione reductase activities; increased ascorbate and glutathione contents; and elevated transcript levels of copper/zinc SOD, manganese SOD, and catalase in leaves under FA and PHBA. Moreover, CSY-P13 increased phosphatase, catalase, urease, and sucrase activities and changed bacterial richness, diversity, and community composition by high throughput sequencing in cucumber-planted soil supplemented with the mixture of FA and PHBA. So CSY-P13 degrades the mixture of FA and PHBA in soil and mitigates stress from the two phenolic compounds in cucumber by activating antioxidant enzymes, changing soil bacterial community, and inducing soil enzymes.

CSI : Alaska

International Nuclear Information System (INIS)

Letwin, S.

2005-01-01

This presentation emphasized the need for northern gas supply at a time when conventional natural gas supplies are decreasing and demand is growing. It highlighted the unique qualifications of Enbridge Inc. in creating an infrastructure to move the supply to where it is in most demand. Enbridge has substantial northern experience and has a unique approach for the construction of the Alaskan Gas Pipeline which entails cooperation, stability and innovation (CSI). Enbridge's role in the joint venture with AltaGas and Inuvialuit Petroleum was discussed along with its role in the construction of the first Canadian pipeline in 1985. The 540 mile pipeline was buried in permafrost. A large percentage of Enbridge employees are of indigenous descent. Enbridge recognizes that the amount of capital investment and the associated risk needed for the Alaska Gas Pipeline will necessitate a partnership of producers, pipeline companies, Native organizations, the State of Alaska, market participants and other interested parties. 9 figs

Iterative Equalization and Interference Alignment for Multiuser MIMO HetNets with Imperfect CSI

Directory of Open Access Journals (Sweden)

Daniel Castanheira

2015-01-01

Full Text Available In this paper we consider a scenario, where several small-cells work under the same coverage area and spectrum of a macrocell. The signals stemming from the small-cell (macrocell users if not carefully dealt with will generate harmful interference into the macrocell (small-cell. To tackle this problem interference alignment and iterative equalization techniques are considered. By using IA all interference generated by the small-cell (macrocell users is aligned along a low dimensional subspace, at the macrocell (small-cells. This reduces considerably the amount of resources allocated, to enable the coexistence of the two systems. However, perfect IA requires the availability of error-free channel state information (CSI at the transmitters. Due to CSI errors one can have substantial performance degradation due to imperfect alignments. Since in this work the IA precoders are based on imperfect CSI, an efficient iterative space-frequency equalization is designed at the receiver side to cope with the residual aligned interference. The results demonstrate that iterative equalization is robust to imperfect CSI and removes efficiently the interference generated by the poorly aligned interference. Close to matched filter bound performance is achieved, with a very few number of iterations.

Investigating CSI: portrayals of DNA testing on a forensic crime show and their potential effects.

Science.gov (United States)

Ley, Barbara L; Jankowski, Natalie; Brewer, Paul R

2012-01-01

The popularity of forensic crime shows such as CSI has fueled debate about their potential social impact. This study considers CSI's potential effects on public understandings regarding DNA testing in the context of judicial processes, the policy debates surrounding crime laboratory procedures, and the forensic science profession, as well as an effect not discussed in previous accounts: namely, the show's potential impact on public understandings of DNA and genetics more generally. To develop a theoretical foundation for research on the "CSI effect," it draws on cultivation theory, social cognitive theory, and audience reception studies. It then uses content analysis and textual analysis to illuminate how the show depicts DNA testing. The results demonstrate that CSI tends to depict DNA testing as routine, swift, useful, and reliable and that it echoes broader discourses about genetics. At times, however, the show suggests more complex ways of thinking about DNA testing and genetics.

Review of sustainability indices and indicators: Towards a new City Sustainability Index (CSI)

Energy Technology Data Exchange (ETDEWEB)

Mori, Koichiro, E-mail: kmori@iis.u-tokyo.ac.jp [Institute of Industrial Science, University of Tokyo (Japan); Christodoulou, Aris, E-mail: aris.christodoulou@ucl.ac.uk [Centre for Transport Studies, University College London (United Kingdom)

2012-01-15

The purpose of this paper is to discuss conceptual requirements for a City Sustainability Index (CSI) and to review existing major sustainability indices/indicators in terms of the requirements. The following indices are reviewed: Ecological Footprint (EF), Environmental Sustainability Index (ESI), Dashboard of Sustainability (DS), Welfare Index, Genuine Progress Indicator (GPI), Index of Sustainable Economic Welfare, City Development Index, emergy/exergy, Human Development Index (HDI), Environmental Vulnerability Index (EVI), Environmental Policy Index (EPI), Living Planet Index (LPI), Environmentally-adjusted Domestic Product (EDP), Genuine Saving (GS), and some applications of composite indices or/and multivariate indicators to local or regional context as case studies. The key conceptual requirements for an adequate CSI are: (i) to consider environmental, economic and social aspects (the triple bottom line of sustainability) from the viewpoint of strong sustainability; (ii) to capture external impacts (leakage effects) of city on other areas beyond the city boundaries particularly in terms of environmental aspects; (iii) to create indices/indicators originally for the purpose of assessing city sustainability; and (iv) to be able to assess world cities in both developed and developing countries using common axes of evaluation. Based on the review, we conclude that it is necessary to create a new CSI that enables us to assess and compare cities' sustainability performance in order to understand the global impact of cities on the environment and human life as compared with their economic contribution. In the future, the CSI will be able to provide local authorities with guidance toward sustainable paths. - Highlights: Black-Right-Pointing-Pointer We derive the four key requirements for a new City Sustainability Index (CSI) system. Black-Right-Pointing-Pointer First, the triple bottom line must be considered in terms of strong sustainability. Black

Review of sustainability indices and indicators: Towards a new City Sustainability Index (CSI)

International Nuclear Information System (INIS)

Mori, Koichiro; Christodoulou, Aris

2012-01-01

The purpose of this paper is to discuss conceptual requirements for a City Sustainability Index (CSI) and to review existing major sustainability indices/indicators in terms of the requirements. The following indices are reviewed: Ecological Footprint (EF), Environmental Sustainability Index (ESI), Dashboard of Sustainability (DS), Welfare Index, Genuine Progress Indicator (GPI), Index of Sustainable Economic Welfare, City Development Index, emergy/exergy, Human Development Index (HDI), Environmental Vulnerability Index (EVI), Environmental Policy Index (EPI), Living Planet Index (LPI), Environmentally-adjusted Domestic Product (EDP), Genuine Saving (GS), and some applications of composite indices or/and multivariate indicators to local or regional context as case studies. The key conceptual requirements for an adequate CSI are: (i) to consider environmental, economic and social aspects (the triple bottom line of sustainability) from the viewpoint of strong sustainability; (ii) to capture external impacts (leakage effects) of city on other areas beyond the city boundaries particularly in terms of environmental aspects; (iii) to create indices/indicators originally for the purpose of assessing city sustainability; and (iv) to be able to assess world cities in both developed and developing countries using common axes of evaluation. Based on the review, we conclude that it is necessary to create a new CSI that enables us to assess and compare cities' sustainability performance in order to understand the global impact of cities on the environment and human life as compared with their economic contribution. In the future, the CSI will be able to provide local authorities with guidance toward sustainable paths. - Highlights: ► We derive the four key requirements for a new City Sustainability Index (CSI) system. ► First, the triple bottom line must be considered in terms of strong sustainability. ► Second, environmental leakage effects beyond city boundaries should

Multifractal property of Chinese stock market in the CSI 800 index based on MF-DFA approach

Science.gov (United States)

Zhu, Huijian; Zhang, Weiguo

2018-01-01

CSI 800 index consists of CSI 500 index and CSI 300 index, aiming to reflect the performance of stocks with large, mid and small size of China A share market. In this paper we analyze the multifractal structure of Chinese stock market in the CSI 800 index based on the multifractal detrended fluctuation analysis (MF-DFA) method. We find that the fluctuation of the closing logarithmic returns have multifractal properties, the shape and width of multifractal spectrum are depended on the weighing order q. More interestingly, we observe a bigger market crash in June-August 2015 than the one in 2008 based on the local Hurst exponents. The result provides important information for further study on dynamic mechanism of return fluctuation and whether it would trigger a new financial crisis.

Structural transformation of CsI thin film photocathodes under exposure to air and UV irradiation

CERN Document Server

Tremsin, A S; Siegmund, O H W

2000-01-01

Transmission electron microscopy has been employed to study the structure of polycrystalline CsI thin films and its transformation under exposure to humid air and UV irradiation. The catastrophic degradation of CsI thin film photocathode performance is shown to be associated with the film dissolving followed by its re-crystallization. This results in the formation of large lumps of CsI crystal on the substrate surface, so that the film becomes discontinuous and its performance as a photocathode is permanently degraded. No change in the surface morphology and the film crystalline structure was observed after the samples were UV irradiated.

Quality Assurance on Undoped CsI Crystals for the Mu2e Experiment

Science.gov (United States)

Atanov, N.; Baranov, V.; Budagov, J.; Davydov, Yu. I.; Glagolev, V.; Tereshchenko, V.; Usubov, Z.; Cervelli, F.; Di Falco, S.; Donati, S.; Morescalchi, L.; Pedreschi, E.; Pezzullo, G.; Raffaelli, F.; Spinella, F.; Colao, F.; Cordelli, M.; Corradi, G.; Diociaiuti, E.; Donghia, R.; Giovannella, S.; Happacher, F.; Martini, M.; Miscetti, S.; Ricci, M.; Saputi, A.; Sarra, I.; Echenard, B.; Hitlin, D. G.; Hu, C.; Miyashita, T.; Porter, F.; Zhang, L.; Zhu, R.-Y.; Grancagnolo, F.; Tassielli, G.; Murat, P.

2018-02-01

The Mu2e experiment is constructing a calorimeter consisting of 1,348 undoped CsI crystals in two disks. Each crystal has a dimension of 34 x 34 x 200 mm, and is readout by a large area silicon PMT array. A series of technical specifications was defined according to physics requirements. Preproduction CsI crystals were procured from three firms: Amcrys, Saint-Gobain and Shanghai Institute of Ceramics. We report the quality assurance on crystal's scintillation properties and their radiation hardness against ionization dose and neutrons. With a fast decay time of 30 ns and a light output of more than 100 p.e./MeV measured with a bi-alkali PMT, undoped CsI crystals provide a cost-effective solution for the Mu2e experiment.

CSI 3.0: a web server for identifying secondary and super-secondary structure in proteins using NMR chemical shifts.

Science.gov (United States)

Hafsa, Noor E; Arndt, David; Wishart, David S

2015-07-01

The Chemical Shift Index or CSI 3.0 (http://csi3.wishartlab.com) is a web server designed to accurately identify the location of secondary and super-secondary structures in protein chains using only nuclear magnetic resonance (NMR) backbone chemical shifts and their corresponding protein sequence data. Unlike earlier versions of CSI, which only identified three types of secondary structure (helix, β-strand and coil), CSI 3.0 now identifies total of 11 types of secondary and super-secondary structures, including helices, β-strands, coil regions, five common β-turns (type I, II, I', II' and VIII), β hairpins as well as interior and edge β-strands. CSI 3.0 accepts experimental NMR chemical shift data in multiple formats (NMR Star 2.1, NMR Star 3.1 and SHIFTY) and generates colorful CSI plots (bar graphs) and secondary/super-secondary structure assignments. The output can be readily used as constraints for structure determination and refinement or the images may be used for presentations and publications. CSI 3.0 uses a pipeline of several well-tested, previously published programs to identify the secondary and super-secondary structures in protein chains. Comparisons with secondary and super-secondary structure assignments made via standard coordinate analysis programs such as DSSP, STRIDE and VADAR on high-resolution protein structures solved by X-ray and NMR show >90% agreement between those made with CSI 3.0. © The Author(s) 2015. Published by Oxford University Press on behalf of Nucleic Acids Research.

Operation and Modulation of H7 Current Source Inverter with Hybrid SiC and Si Semiconductor Switches

DEFF Research Database (Denmark)

Wang, Weiqi; Gao, Feng; Yang, Yongheng

2018-01-01

This paper proposes an H7 current source inverter (CSI) consisting of a single parallel-connected silicon carbide (SiC) switch and a traditional silicon (Si) H6 CSI. The proposed H7 CSI takes the advantages of the SiC switch to maintain high efficiency, while significantly increasing the switching...... as an all-SiC-switch converter in terms of high performance and high efficiency with reduced DC inductance. It provides a cost-effective solution to addressing the efficiency issue of conventional CSI systems. Simulations and experiments are performed to validate the effectiveness of the proposed H7 CSI...

Secure Communication for Two-Way Relay Networks with Imperfect CSI

Directory of Open Access Journals (Sweden)

Cong Sun

2017-09-01

Full Text Available This paper considers a two-way relay network, where two legitimate users exchange messages through several cooperative relays in the presence of an eavesdropper, and the Channel State Information (CSI of the eavesdropper is imperfectly known. The Amplify-and-Forward (AF relay protocol is used. We design the relay beamforming weights to minimize the total relay transmit power, while requiring the Signal-to-Noise-Ratio (SNRs of the legitimate users to be higher than the given thresholds and the achievable rate of the eavesdropper to be upper-bounded. Due to the imperfect CSI, a robust optimization problem is summarized. A novel iterative algorithm is proposed, where the line search technique is applied, and the feasibility is preserved during iterations. In each iteration, two Quadratically-Constrained Quadratic Programming (QCQP subproblems and a one-dimensional subproblem are optimally solved. The optimality property of the robust optimization problem is analyzed. Simulation results show that the proposed algorithm performs very close to the non-robust model with perfect CSI, in terms of the obtained relay transmit power; it~achieves higher secrecy rate compared to the existing work. Numerically, the proposed algorithm converges very quickly, and more than 85% of the problems are solved optimally.

Influence of bias voltage on the stability of CsI photocathodes exposed to air

CERN Document Server

Nitti, M A; Nappi, E; Singh, B K; Valentini, A

2002-01-01

We describe a possible correlation between the bias voltage applied to the substrate during the growth of CsI photocathodes and the variation of quantum efficiency (QE) after one day exposure to humid air. It was found that fresh samples are much less sensitive to humid air when a high negative bias voltage was applied during film growth. A model based on surface film interaction with water molecules is presented for the observed effect. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) measurements have been performed to examine, respectively, the bulk structure and the surface of fresh and exposed CsI samples. Also reported are transmittance measurements for fresh and aged CsI samples in the wavelength range 190-850 nm.

Purine 3':5'-cyclic nucleotides with the nucleobase in a syn orientation: cAMP, cGMP and cIMP.

Science.gov (United States)

Řlepokura, Katarzyna Anna

2016-06-01

Purine 3':5'-cyclic nucleotides are very well known for their role as the secondary messengers in hormone action and cellular signal transduction. Nonetheless, their solid-state conformational details still require investigation. Five crystals containing purine 3':5'-cyclic nucleotides have been obtained and structurally characterized, namely adenosine 3':5'-cyclic phosphate dihydrate, C10H12N5O6P·2H2O or cAMP·2H2O, (I), adenosine 3':5'-cyclic phosphate 0.3-hydrate, C10H12N5O6P·0.3H2O or cAMP·0.3H2O, (II), guanosine 3':5'-cyclic phosphate pentahydrate, C10H12N5O7P·5H2O or cGMP·5H2O, (III), sodium guanosine 3':5'-cyclic phosphate tetrahydrate, Na(+)·C10H11N5O7P(-)·4H2O or Na(cGMP)·4H2O, (IV), and sodium inosine 3':5'-cyclic phosphate tetrahydrate, Na(+)·C10H10N4O7P(-)·4H2O or Na(cIMP)·4H2O, (V). Most of the cyclic nucleotide zwitterions/anions [two from four cAMP present in total in (I) and (II), cGMP in (III), cGMP(-) in (IV) and cIMP(-) in (V)] are syn conformers about the N-glycosidic bond, and this nucleobase arrangement is accompanied by Crib-H...Npur hydrogen bonds (rib = ribose and pur = purine). The base orientation is tuned by the ribose pucker. An analysis of data obtained from the Cambridge Structural Database made in the context of syn-anti conformational preferences has revealed that among the syn conformers of various purine nucleotides, cyclic nucleotides and dinucleotides predominate significantly. The interactions stabilizing the syn conformation have been indicated. The inter-nucleotide contacts in (I)-(V) have been systematized in terms of the chemical groups involved. All five structures display three-dimensional hydrogen-bonded networks.

Occurrence of C35-C45 polyprenols in filamentous and unicellular cyanobacteria

NARCIS (Netherlands)

Bauersachs, T.; Schouten, S.; Compaoré, J.; Stal, L.J.; Sinninghe Damsté, J.S.

2010-01-01

Polyprenols, regular (head-to-tail) isoprenoid alcohols with 7-9 prenyl units, were tentatively identified in several cultivated cyanobacteria Heptaprenol (C35), octaprenol (C40) and a suite of nonaprenols (C45) were present in unicellular and filamentous non-heterocystous cyanobacteria, while they

Professional ASPNET 35 SP1 Edition In C# and VB

CERN Document Server

Evjen, Bill; Rader, Devin

2009-01-01

Professional ASP.NET 3.5 SP1 In C# and VB. ASP.NET 3.5 brings the power of Visual Studio® 2008 along with the multitude of language improvements in C# 2008 and Visual Basic® 2008 as well as powerful new technology called LINQ, together with the ASP.NET 2.0 Framework you already know and love. Packed with valuable coverage of ASP.NET 3.5 SP1, this essential resource offers both C# and VB examples throughout the book, and shares new and updated content on the ADO.NET Entity Framework, ADO.NET Dynamic Data, and ADO.NET Data Services. While ASP.NET 3.5 boasts server controls like the ListView and

Two-way CSI-assisted AF relaying with HPA nonlinearity

KAUST Repository

Qi, Jian; Aissa, Sonia; Alouiniz, Mohamed-Slim

2015-01-01

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal

Occurrence of C35-C45 polyprenols in filamentous and unicellular cyanobacteria

NARCIS (Netherlands)

Bauersachs, T.; Schouten, S.; Compaore, J.; Stal, L.J.; Sinninghe Damsté, J.S.

2010-01-01

Polyprenols, regular (head-to-tail) isoprenoid alcohols with 7–9 prenyl units, were tentatively identified in several cultivated cyanobacteria. Heptaprenol (C35), octaprenol (C40) and a suite of nonaprenols (C45) were present in unicellular and filamentous non-heterocystous cyanobacteria, while they

Radiation damage in undoped CsI and CsI(Tl)

International Nuclear Information System (INIS)

Woody, C.L.; Kierstead, J.A.; Levy, P.W.; Stoll, S.

1992-01-01

Radiation damage has been studied in undoped CsI and CsI(TI) crystals using 60 Co gamma radiation for doses up to ∼ 4.2 x 10 6 . Samples from various manufacturers were measured ranging in size from 2.54 cm long cylinders to a 30 cm long block. Measurements were made on the change in optical transmission and scintillation light output as a function of dose. Although some samples showed a small change in transmission, a significant change in light output was observed for all samples. Recovery from damage was also studied as a function of time and exposure to UV light. A short lived phosphorescence was observed in undoped CsI, similar to the phosphorescence seen in CsI(TI)

Study of the Quantum Efficiency of CsI Photocathodes Exposed to Oxygen and Water Vapour

CERN Document Server

Di Mauro, A; Piuz, François; Schyns, E M; Van Beelen, J B; Williams, T D

2000-01-01

The operation of CsI photocathodes in gaseous detectors requires special attention to the purity of the applied gas mixtures.We have studied the influence of oxygen and water vapour contaminations on the performance of CsI photocathodes for theALICE HMPID RICH prototype. Measurements were done through comparison of Cherenkov rings obtained from beamtests. Increased levels of oxygen and water vapour did not show any effect on the performance. The results of this studyfound a direct application in the way of storing CsI photocathodes over long periods nad in particular in the shipment of theHMPID prototype from CERN to the STAR experiment at BNL. (Abstract only available,full text to follow)

Process-property relationships of SiC chemical vapor deposition in the Si/H/C/O system

International Nuclear Information System (INIS)

Richardson, C.; Takoudis, C.G.

1999-01-01

The thermal, chemical, and physical properties of SiC make it an attractive material for a wide range of applications from wear resistant coatings on tools to high temperature microelectronics operations. A comprehensive thermodynamic analysis has been performed for the Si/H/C/O system from which a priori process-property relationships of the chemical vapor deposition (CVD) of silicon carbide (SiC) are obtained. The parameter space for pure silicon carbide growth is reported for five orders of magnitude of the system water vapor level (1 ppb--100 ppm), four orders of magnitude of system pressure (0.1--760 Torr), and two orders of magnitude of C/Si feed ratio (0.25--20) and H 2 /Si feed ratio (50--10,000). Lower growth temperatures for pure SiC are predicted in clean systems with low system water vapor levels, at stoichiometric to near carbon excess conditions (C/Si ≅ 1 to C/Si > 1), at high carrier gas flow rates (large H 2 /Si feed ratios), and at low operating pressures. Because relative C/Si and H 2 /Si feed ratios have been considered, the predictions in this study are applicable to both multiple and single precursor systems. Further, these results are valid for the CVD of α-SiC as well as β-SiC. Experimental data reported on the growth of α-SiC and β-SiC are found to be in satisfactory agreement with the theoretical predictions, for numerous systems that include multiple and single source, silicon and carbon, species

Financial instrument pricing using C++

CERN Document Server

Duffy, Daniel J

2004-01-01

One of the best languages for the development of financial engineering and instrument pricing applications is C++. This book has several features that allow developers to write robust, flexible and extensible software systems. The book is an ANSI/ISO standard, fully object-oriented and interfaces with many third-party applications. It has support for templates and generic programming, massive reusability using templates (?write once?) and support for legacy C applications. In this book, author Daniel J. Duffy brings C++ to the next level by applying it to the design and implementation of class

Achievable Rates of Cognitive Radio Networks Using Multi-Layer Coding with Limited CSI

KAUST Repository

Sboui, Lokman

2016-03-01

In a Cognitive Radio (CR) framework, the channel state information (CSI) feedback to the secondary transmitter (SU Tx) can be limited or unavailable. Thus, the statistical model is adopted in order to determine the system performance using the outage concept. In this paper, we adopt a new approach using multi-layer-coding (MLC) strategy, i.e., broadcast approach, to enhance spectrum sharing over fading channels. First, we consider a scenario where the secondary transmitter has no CSI of both the link between SU Tx and the primary receiver (cross-link) and its own link. We show that using MLC improves the cognitive rate compared to the rate provided by a singlelayer- coding (SLC). In addition, we observe numerically that 2-Layer coding achieves most of the gain for Rayleigh fading. Second, we analyze a scenario where SU Tx is provided by partial CSI about its link through quantized CSI. We compute its achievable rate adopting the MLC and highlight the improvement over SLC. Finally, we study the case in which the cross-link is perfect, i.e., a cooperative primary user setting, and compare the performance with the previous cases. We present asymptotic analysis at high power regime and show that the cooperation enhances considerably the cognitive rate at high values of the secondary power budget.

CsI and some new photocathodes

International Nuclear Information System (INIS)

Anderson, D.F.; Kwan, S.; Peskov, V.

1993-06-01

A discussion of the possible sources of discrepancies in the measurements of the quantum efficiency of CsI photocathodes is presented. We propose that the major causes for disagreements in QE are due to the QE dependence on the current density extracted from the photocathode, on the electric field, and on the temperature of the photocathode. Preliminary results on TMAE enhanced GaAs and Si, plus TMAE protected CsTe and SbCs photocathodes, operated in gas, are also presented

FY16 ASC ATDM L2 Milestone: PARTISN Research and FleCSI Updates

Energy Technology Data Exchange (ETDEWEB)

Womeldorff, Geoffrey Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Payne, Joshua Estes [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bergen, Benjamin Karl [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-01

These are slides for a presentation on PARTISN Research and FleCSI Updates. The following topics are covered: SNAP vs PARTISN, Background Research, Production Code (structural design and changes, kernel design and implementation, lessons learned), NuT IMC Proxy, FleCSI Update (design and lessons learned). It can all be summarized in the following manner: Kokkos was shown to be effective in FY15 in implementing a C++ version of SNAP's kernel. This same methodology was applied to a production IC code, PARTISN. This was a much more complex endeavour than in FY15 for many reasons; a C++ kernel embedded in Fortran, overloading Fortran memory allocations, general language interoperability, and a fully fleshed out production code versus a simplified proxy code. Lessons learned are Legion. In no particular order: Interoperability between Fortran and C++ was really not that hard, and a useful engineering effort. Tracking down all necessary memory allocations for a kernel in a production code is pretty hard. Modifying a production code to work for more than a handful of use cases is also pretty hard. Figuring out the toolchain that will allow a successful implementation of design decisions is quite hard, if making use of "bleeding edge" design choices. In terms of performance, production code concurrency architecture can be a virtual showstopper; being too complex to easily rewrite and test in a short period of time, or depending on tool features which do not exist yet. Ultimately, while the tools used in this work were not successful in speeding up the production code, they helped to identify how work would be done, and provide requirements to tools.

Corporate social investment and a company’s image: A case of a CSI initiative in a South African low income community

Directory of Open Access Journals (Sweden)

Paul-Francois Muzindutsi

2015-11-01

Full Text Available One of the goals of corporate social investment (CSI is to ensure that a company becomes a responsible entity which acts as a conscientious citizen within a society. CSI plays an important role in enhancing how a company is perceived within the community it operates in. This paper used a combination of qualitative and quantitative research designs to investigate the effect of a specific CSI initiative on a company’s image within a low income community in South Africa. Semi-structured interviews and survey questionnaire were used to collect data from community members in the township of Bophelong, South Africa. Results show that, if adequately managed, CSI initiatives tend to enhance company’s image as well as its relations with the community it operates in. However, if not adequately managed CSI can created unreachable expectations that can negatively affect a company’s image. Thus, companies better manage their CSI initiatives have an increased opportunity to enhance their reputation within the community they operate in.

TOTAL NUCLEAR-REACTION PROBABILITY OF 270 TO 390 N-14 IONS IN SI AND CSI

NARCIS (Netherlands)

WARNER, RE; CARPENTER, CL; FETTER, JM; WAITE, WF; WILSCHUT, HW; HOOGDUIN, JM

A magnetic spectrograph and position-sensitive detectors were used to measure the total nuclear reaction probability eta(R) for alpha + CsI at 116 MeV, N-14 + CsI at 265 and 385 MeV, and N-14 + Si at 271 and 390 MeV. From these eta(R)'s, average reaction cross sections sigma(R) were deduced for

The Communication Styles Inventory (CSI): a six-dimensional behavioral model of communication styles and its relation with personality

NARCIS (Netherlands)

de Vries, R.E.; Bakker-Pieper, A.; Konings, F.E.; Schouten, B.

2013-01-01

In this study, a six-dimensional model of communication styles is proposed and operationalized using the Communication Styles Inventory (CSI). The CSI distinguishes between six domain-level communicative behavior scales, Expressiveness, Preciseness, Verbal Aggressiveness, Questioningness,

Influence of boron vapor on transport behavior of deposited CsI during heating test simulating a BWR severe accident condition

Energy Technology Data Exchange (ETDEWEB)

Sato, Isamu, E-mail: sato.isamu@jaea.go.jp; Onishi, Takashi; Tanaka, Kosuke; Iwasaki, Maho; Koyama, Shin-ichi

2015-06-15

In order to evaluate influence of B on the release and transport of Cs and I during severe accidents, basic experiments have been performed on the interaction between deposited Cs/I compounds and vapor/aerosol B compounds. CsI and B{sub 2}O{sub 3} were utilized as a Cs/I compound and a B compound, respectively. Deposited CsI on the thermal gradient tube (TGT) at temperatures ranging from 423 K to 1023 K was reacted with vapor/aerosol B{sub 2}O{sub 3}, and then observed how it changed Cs/I deposition profiles. As a result, vapor/aerosol B{sub 2}O{sub 3} stripped a portion of deposited CsI within a temperature range from 830 K to 920 K to make gaseous CsBO{sub 2} and I{sub 2}. In addition, gaseous I{sub 2} was re-deposited at a temperature range from 530 K to 740 K, while CsBO{sub 2} travelled through the sampling tubes and filters without deposition. It is evident that B enables Cs compounds such as CsBO{sub 2} to transport Cs to the colder regions.

Uplink Contention-based CSI Feedback with Prioritized Layers for a Multi-Carrier System

DEFF Research Database (Denmark)

Kaneko, Megumi; Hayashi, Kazunori; Popovski, Petar

2012-01-01

, several works have considered contention-based CSI feedback in the UL control channel. We propose such a feedback scheme for a generic MC system, based on the idea of variable collision protection, where the probability that a feedback information experiences a collision depends on its importance......Optimized resource allocation of the Downlink (DL) in wireless systems utilizing Multi-Carrier (MC) transmission requires Channel State Information (CSI) feedback for each user/subchannel to the Base Station (BS), consuming a high amount of Uplink (UL) radio resources. To alleviate this problem...

Role of the substrate reflectance and surface-bulk treatments in CsI quantum efficiency

CERN Document Server

Singh, B K; Nitti, M A; Valentini, A

2003-01-01

We have experimentally investigated the following aspects related to the quantum efficiency of CsI photocathodes: the type of substrate, the film thickness and the effect of a 'bulk treatment' during the film growth. We discovered that, using a high reflectivity aluminium substrate, the photoemission of very thin CsI film is enhanced. Our study also revealed that photocathodes become less sensitive to moisture when a negative bias voltage is applied to the substrate during the film deposition process.

A surfeit of science: The "CSI effect" and the media appropriation of the public understanding of science.

Science.gov (United States)

Cole, Simon A

2015-02-01

Over the past decade, popular media has promulgated claims that the television program CSI and its spinoffs and imitators have had a pernicious effect on the public understanding of forensic science, the so-called "CSI effect." This paper analyzes those media claims by documenting the ways in which the media claims that CSI "distorts" an imagined "reality." It shows that the media appropriated the analytic stance usually adopted by science advocates, portraying the CSI effect as a social problem in science communication. This appropriation was idiosyncratic in that it posited, as a social problem, a "surfeit" of knowledge and positive imagery about science, rather than the more familiar "deficits." In addition, the media simultaneously appropriated both "traditional" and "critical" PUS discourses. Despite this apparent contradiction, the paper concludes that, in both discourses, the media and its expert informants insist upon their hegemony over "the public" to articulate the "reality" of forensic science. © The Author(s) 2013.

Digestibilidade determinada pelo método indireto usando o n-alcano C35 Digestibility determinate by indirect method using C35 n-alkane

Directory of Open Access Journals (Sweden)

Dimas Estrásulas de Oliveira

2000-06-01

Full Text Available Foi feito um trabalho de extração e análise de n-alcanos com o objetivo de investigar o uso do n-alcano (C35 presente nas forragens como um indicador interno para determinação de digestibilidade. Foram utilizadas amostras de experimentos de digestibilidade convencional realizados previamente entre os anos de 1978 e 1982. O C35 subestimou as digestibilidades da matéria seca e orgânica, apresentando diferença média, em relação ao método in vivo, de 4,68 (± 0,69 e 4,43 (± 0,85 unidades percentuais, respectivamente. O coeficiente de regressão não diferiu da unidade, indicando que os métodos foram equivalentes, havendo, porém, a necessidade de um fator de correção. Os coeficientes de correlação para a matéria seca e orgânica, observados entre os dois métodos, foram 0,87 e 0,85, respectivamente. O C35 apresentou recuperação fecal média de 91,76% (± 7,94, que contribuiu para o vício da técnica.An experiment was conducted, on extraction and analysis of n-alkanes, to investigate the use of n-alkane (C35 present in forages as an internal marker for the digestibility determination. Samples of forages and feces were taken from conventional digestibility trials, which were previous conducted from 1978 to 1982. The C35 underestimated the dry matter and organic matter digestibilities, presenting an average difference in relation to in vivo of 4.68 (± 0.69 and 4,43 (± 0.85 perceptual units, respectively. The coefficient of regression did not differ from the unit, indicating that both methods were equivalent, having, however, the necessity of a correction factor. The coefficients of correlation observed for the dry and organic matter between the two methods were 0.87 and 0.85, respectively. The average fecal recovery of C35 was 91.76% (± 7.94, and this contributed to the bias of the method.

Development of Large Area CsI Photocathodes for the ALICE/HMPID RICH Detector

CERN Document Server

Hoedlmoser, H; Schyns, E

2005-01-01

The work carried out within the framework of this PhD deals with the measurement of the photoelectric properties of large area thin film Cesium Iodide (CsI) photocathodes (PCs) which are to be used as a photon converter in a proximity focusing RICH detector for High Momentum Particle Identification (HMPID) in the ALICE experiment at the LHC. The objective was to commission a VUV-scanner setup for in-situ measurements of the photoelectric response of the CsI PCs immediately after the thin film coating process and the use of this system to investigate the properties of these photon detectors. Prior to this work and prior to the finalization of the ALICE/HMPID detector design, R&D work investigating the properties of CsI PCs had been performed at CERN and at other laboratories in order to determine possible substrates and optimized thin film coating procedures. These R&D studies were usually carried out with small samples on different substrates and with various procedures with sometimes ambiguous result...

Minimax robust power split in AF relays based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish

2011-09-01

An optimal power control among source and relay nodes in presence of channel state information (CSI) is vital for an efficient amplify and forward (AF) based cooperative communication system. In this work, we study the optimal power split (power control) between the source and relay node in presence of an uncertainty in the CSI. The prime contribution is to solve the problem based on an uncertain long-term knowledge of both the first and second hop CSI (requiring less frequent updates), and under an aggregate network-level power constraint. We employ the minimax optimization methodology to arrive at the minimax robust optimal power split, that offers the best possible guarantee on the end-to-end signal to noise ratio (SNR). The derived closed form analytical expressions admit simple intuitive interpretations and are easy to implement in real-world AF relaying systems. Numerical results confirm the advantages of incorporating the presence of uncertainty into the optimization problem, and demonstrate the usefulness of the proposed minimax robust optimal power split. © 2011 IEEE.

Spinal instrumentation for unstable C1-2 injury.

Science.gov (United States)

Mizuno, J; Nakagawa, H

1999-06-01

Seventeen patients with unstable C1-2 injuries were treated between 1990 and 1997. Various methods of instrumentation surgery were performed in 16 patients, excluding a case of atlantoaxial rotatory fixation. Posterior stabilization was carried out in 14 cases using Halifax interlaminar clamp, Sof'wire or Danek cable, or more recently, transarticular screws. Transodontoid anterior screw fixation was performed in four cases of odontoid process fractures, with posterior instrumentation in two cases because of malunion. Rigid internal fixation by instrumentation surgery for the unstable C1-2 injury avoids long-term application of a Halo brace and facilitates early rehabilitation. However, the procedure is technically demanding with the risk of neural and vascular injuries, particularly with posterior screw fixation. Sagittal reconstruction of thin-sliced computed tomography scans at the C1-2 region, neuronavigator, and intraoperative fluoroscopy are essential to allow preoperative surgical planning and intraoperative guidance.

Instrumentation qualification. Seismic qualification of C-E instrumentation equipment. Part One

International Nuclear Information System (INIS)

1977-05-01

A summary of the C-E seismic qualification program utilized to demonstrate the seismic design adequacy of the instrumentation and control equipment used in C-E supplied Nuclear Steam Supply Systems (NSSS) is presented. The report is divided into two parts. Part One includes the equipment seismic requirements and a description of the qualification methods. Part Two lists the specific equipment by nuclear station in which it is used and the equipment test results are summarized in a standard data sheet format to facilitate review. The seismic requirements are based on individual contract commitments with C-E customers and the NRC Standard Review Plan, Section 3.10 ''Seismic Qualification of Category I Instrumentation and Electrical Equipment.'' Equipment is qualified for use in a seismic environment where damage potential to the equipment is less than or equal to that simulated seismic environment to which it has been qualified. The anticipated Safe Shutdown Earthquake (SSE) environment at the inservice location of equipment should be confirmed by each applicant as not exceeding that to which it is qualified

Corporate Social Irresponsibility (CSI): Everything you say, or not say, can be held against you

OpenAIRE

Jonsson, Veronica; Stéen, Josefine

2016-01-01

Corporate social irresponsibility (CSI), as an opposite of corporate social responsibility (CSR), refers to corporation’s failure to act responsibly. To address the actions connected to CSR and CSI, corporations need to overcome the challenges of communicating to their stakeholders and to be transparent. Stakeholders have become more skeptical regarding if the corporations are actually living up to the communicated standards. In other words, if corporations are ‘doing as they say’ and if they...

Study on the effect of deposition rate and concentration of Eu on the fluorescent lifetime of CsI: Tl thin film

Energy Technology Data Exchange (ETDEWEB)

Xie, Yijun; Guo, Lina [University of Electronic Science and Technology of China, State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, Chengdu 610054 (China); Liu, Shuang, E-mail: shuangliu@uestc.edu.cn [University of Electronic Science and Technology of China, State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, Chengdu 610054 (China); Wang, Qianfeng; Zhang, Shangjian; Liu, Yong [University of Electronic Science and Technology of China, State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, Chengdu 610054 (China); Zhong, Zhiyong [University of Electronic Science and Technology of China, State Key Laboratory of Electronic Thin Films and Integrated Devices, Chengdu 610054 (China)

2017-06-21

Although there are many new scintillators being developed recently, CsI: Tl is still very efficient among them. The fluorescent lifetime is a very important parameter of CsI: Tl thin film and two series of experiments have been conducted to learn about it. Our experiments, however, have demonstrated that the deposition rate and the codoping of Eu{sup 2+} will significantly influence its fluorescent lifetime. In order to increase the efficiency of the imaging system, we intend to obtain a higher fluorescent lifetime for CsI: Tl thin film by controlling these two conditions. - Highlights: • We used vacuum vapor deposition method to grow the high-quality thin films. • The relationship between the deposition rate and the fluorescent lifetime of CsI: Tl thin film was tested. • Concentration of Eu on fluorescent lifetime of the CsI: Tl thin film was studied.

Novel Robust Optimization and Power Allocation of Time Reversal-MIMO-UWB Systems in an Imperfect CSI

Directory of Open Access Journals (Sweden)

Sajjad Alizadeh

2013-03-01

Full Text Available Time Reversal (TR technique is an attractive solution for a scenario where the transmission system employs low complexity receivers with multiple antennas at both transmitter and receiver sides. The TR technique can be combined with a high data rate MIMO-UWB system as TR-MIMO-UWB system. In spite of TR's good performance in MIMO-UWB systems, it suffers from performance degradation in an imperfect Channel State Information (CSI case. In this paper, at first a robust TR pre-filter is designed together with a MMSE equalizer in TR-MIMO-UWB system where is robust against channel imperfection conditions. We show that the robust pre-filter optimization technique, considerably improves the BER performance of TR-MIMO-UWB system in imperfect CSI, where temporal focusing of the TR technique is kept, especially for high SNR values. Then, in order to improve the system performance more than ever, a power loading scheme is developed by minimizing the average symbol error rate in an imperfect CSI. Numerical and simulation results are presented to confirm the performance advantage attained by the proposed robust optimization and power loading in an imperfect CSI scenario.

Examination of the "CSI Effect" on Perceptions of Scientific and Testimonial Evidence in a Hong Kong Chinese Sample.

Science.gov (United States)

Hui, Cora Y T; Lo, T Wing

2017-05-01

Television is a powerful medium through which to convey information and messages to the public. The recent proliferation of forensic science and criminal justice information throughout all forms of media, coupled with raised expectations toward forensic evidence, has led some to suspect that a "CSI effect" ( Crime Scene Investigation effect) is taking place. The present study contributes to the literature addressing the CSI effect in two ways. First, it examines whether the CSI effect exists in the Chinese population of Hong Kong. Second, using a mock-jury paradigm, it empirically examines a more integrative perspective of the CSI effect. It was found that, although the amount of media coverage involving forensic evidence does influence participants' perception of legal evidence to some degree, such a perception does not affect participants' legal decision making. Viewers of forensic dramas were not more likely to convict the defendant when forensic evidence was presented and not less likely to convict when only testimonial evidence was presented. The only significant predictor of the defendant's culpability when scientific evidence was presented was participants' ratings of the reliability of scientific evidence. Results from the present study lend no support to the existence of the CSI effect in Hong Kong.

Argon plasma treatment of silicon nitride (SiN) for improved antireflection coating on c-Si solar cells

Energy Technology Data Exchange (ETDEWEB)

Ghosh, Hemanta; Mitra, Suchismita; Saha, Hiranmay; Datta, Swapan Kumar; Banerjee, Chandan, E-mail: chandanbanerjee74@gmail.com

2017-01-15

Highlights: • Antireflection properties of argon plasma treated silicon nitride layer and its effect on crystalline silicon solar cell. • The reduction in reflection due to the formation of a silicon oxynitride/silicon nitride double layer. • EQE reveals a relative increase of 2.72% in J{sub sc} and 4.46% in conversion efficiency. - Abstract: Antireflection properties of argon plasma treated silicon nitride layer and its effect on crystalline silicon solar cell is presented here. Hydrogenated silicon nitride (a-SiN:H) layer has been deposited on a silicon substrate by Plasma Enhanced Chemical Vapour Deposition (PECVD) using a mixture of silane (SiH{sub 4}), ammonia (NH{sub 3}) and hydrogen (H{sub 2}) gases followed by a argon plasma treatment. Optical analysis reveals a significant reduction in reflectance after argon plasma treatment of silicon nitride layer. While FESEM shows nanostructures on the surface of the silicon nitride film, FTIR reveals a change in Si−N, Si−O and N−H bonds. On the other hand, ellipsometry shows the variation of refractive index and formation of double layer. Finally, a c-Si solar cell has been fabricated with the said anti-reflection coating. External quantum efficiency reveals a relative increase of 2.72% in the short circuit current density and 4.46% in conversion efficiency over a baseline efficiency of 16.58%.

The answers are within me. An evaluation of a person centred counselling service for men at HMP Doncaster who have had experience of domestic violence 2005-2007

OpenAIRE

Hamilton, P.; Wilkinson, K.; Meadows, L.; Cadet, N.

2008-01-01

This report is the second year evaluation of the person centred counselling service for male victims and perpetrators of domestic violence at HMP Doncaster in 2006/7. This report follows on from the previous year's evaluation, Raging Anger Within Me, which evaluated this project in 2005/6. Initiated by the Doncaster Rape and Sexual Abuse Counselling Centre (DRSACC), the second year of counselling service delivery was also funded by Lloyds TSB and the Tudor Trust.\\ud The report provides a back...

Opportunistic Energy-Aware Amplify-and-Forward Cooperative Systems with Imperfect CSI

KAUST Repository

Amin, Osama; Bedeer, Ebrahim; Ahmed, Mohamed Hossam; Dobre, Octavia; Alouini, Mohamed-Slim

2015-01-01

an energyefficient relay assisted communication system based on estimated channel state information (CSI). It employs amplify-andforward relaying and switches between different communication schemes, which are known as direct-transmission, two-hop and cooperative

SU-E-I-11: Cascaded Linear System Model for Columnar CsI Flat Panel Imagers with Depth Dependent Gain and Blur

International Nuclear Information System (INIS)

Peng, B; Lubinsky, A; Zheng, H; Zhao, W; Teymurazyan, A

2014-01-01

Purpose: To implement a depth dependent gain and blur cascaded linear system model (CLSM) for optimizing columnar structured CsI indirect conversion flat panel imager (FPI) for advanced imaging applications. Methods: For experimental validation, depth dependent escape efficiency, e(z), was extracted from PHS measurement of different CsI scintillators (thickness, substrate and light output). The inherent MTF and DQE of CsI was measured using high resolution CMOS sensor. For CLSM, e(z) and the depth dependent MTF(f,z), were estimated using Monte Carlo simulation (Geant4) of optical photon transport through columnar CsI. Previous work showed that Monte Carlo simulation for CsI was hindered by the non-ideality of its columnar structure. In the present work we allowed variation in columnar width with depth, and assumed diffusive reflective backing and columns. Monte Carlo simulation was performed using an optical point source placed at different depth of the CsI layer, from which MTF(z,f) and e(z) were computed. The resulting e(z) with excellent matching with experimental measurements were then applied to the CLSM, Monte Carlo simulation was repeated until the modeled MTF, DQE(f) also match experimental measurement. Results: For a 150 micron FOS HL type CsI, e(z) varies between 0.56 to 0.45, and the MTF at 14 cycles/mm varies between 62.1% to 3.9%, from the front to the back of the scintillator. The overall MTF and DQE(f) at all frequencies are in excellent agreement with experimental measurements at all frequencies. Conclusion: We have developed a CLSM for columnar CsI scintillators with depth dependent gain and MTF, which were estimated from Monte Carlo simulation with novel optical simulation settings. Preliminary results showed excellent agreement between simulation results and experimental measurements. Future work is aimed at extending this approach to optimize CsI screen optic design and sensor structure for achieving higher DQE(f) in cone-beam CT, which uses

Generation of CsI cluster ions for mass calibration in matrix-assisted laser desorption/ionization mass spectrometry

NARCIS (Netherlands)

Lou, X.; Dongen, van J.L.J.; Meijer, E.W.

2010-01-01

A simple method was developed for the generation of cesium iodide (CsI) cluster ions up to m/z over 20,000 in matrix-assisted laser desorption/ionization mass spectrometry (MALDI MS). Calibration ions in both positive and negative ion modes can readily be generated from a single MALDI spot of CsI(3)

CSI flight experiment projects of the Naval Research Laboratory

Science.gov (United States)

Fisher, Shalom

1993-02-01

The Naval Research Laboratory (NRL) is involved in an active program of CSI flight experiments. The first CSI flight experiment of the Naval Research Laboratory, the Low Power Atmospheric Compensation Experiment (LACE) dynamics experiment, has successfully measured vibrations of an orbiting satellite with a ground-based laser radar. The observations, made on January 7, 8 and 10, 1991, represent the first ever measurements of this type. In the tests, a narrowband heterodyne CO2 laser radar, operating at a wavelength of 10.6 microns, detected vibration induced differential-Doppler signatures of the LACE satellite. Power spectral densities of forced oscillations and modal frequencies and damping rates of free-damped vibrations were obtained and compared with finite element structural models of the LACE system. Another manifested flight experiment is the Advanced Controls Technology Experiment (ACTEX) designed to demonstrate active and passive damping with piezo-electric (PZT) sensors and actuators. This experiment was developed under the management of the Air Force Phillips Laboratory with integration of the experiment at NRL. It is to ride as a secondary, or 'piggyback,' experiment on a future Navy satellite.

On some regularities of metal oxide solubility in molten CsI at T = 973 K

Energy Technology Data Exchange (ETDEWEB)

Cherginets, V.L., E-mail: v_cherginets@ukr.net [Institute for Scintillation Materials, National Academy of Sciences of Ukraine, Lenin Avenue, 60, Kharkov 61001 (Ukraine); National Technical University ' Kharkiv Polytechnical Institute' , 21 Frunze St., 61002 Kharkov (Ukraine); Rebrova, T.P.; Datsko, Yu.N.; Shtitelman, V.A. [Institute for Scintillation Materials, National Academy of Sciences of Ukraine, Lenin Avenue, 60, Kharkov 61001 (Ukraine); Bryleva, E.Yu. [State Scientific Organization STC ' Institute for Single Crystals' , National Academy of Sciences of Ukraine, Lenin Avenue, 60, Kharkov 61001 (Ukraine)

2011-08-15

Highlights: > CdO, ZnO, NiO, and EuO are insoluble in CsI melt at 973 K. > The oxide solubilities are lower than those in chloride melts. > The oxide solubilities reduce with the cation radius. > ZnO, NiO, and EuO are suitable for scavenging CsO from oxide ion traces. - Abstract: Solubility products of CdO (pK{sub s,CdO} = 6.80 {+-} 0.2), ZnO (pK{sub s,ZnO} = 10.0 {+-} 0.5), NiO (pK{sub s,NiO} = 11.2 {+-} 0.2) and EuO (pK{sub s,EuO} = 13.1 {+-} 0.2) in molten CsI at T = 973 K are determined by potentiometric titration of (0.02 to 0.03) mol . kg{sup -1} solutions of the corresponding metal chlorides by strong base (KOH) using a membrane oxygen electrode Pt(O{sub 2})|ZrO{sub 2}(Y{sub 2}O{sub 3}) as an indicator. On the basis of pK{sub s,MeO} values, all the oxides studied are referred to practically insoluble in molten CsI. The values of the oxide solubility in CsI melt are lower than the corresponding values in molten alkali metal chlorides. This can be explained by 'softer' basic properties of I{sup -} as compared with Cl{sup -} in the frames of the Pearson 'hard' and 'soft' acid-base concept. In the oxide samples studied, the values of the solubility fall with the decreasing cation radius. The correlation between pK{sub s,MeO} and the polarizing action by Goldshmidt (Zr{sub Me{sup 2+}}{sup -2}) of the cation is practically linear and may be proposed for estimation of the solubility of s- and d- element oxides in molten CsI on the basis of their cation radii.

Synthesis of /sup 14/C- and /sup 35/S-labelled 2-mercaptobenzimidazoles

Energy Technology Data Exchange (ETDEWEB)

Doerge, D R

1988-09-01

/sup 14/C- and /sup 35/S-labelled 2-mercaptobenzimidazole and 1-methyl-2-mercaptobenzimidazole were synthesized from /sup 14/C-carbon disulfide, /sup 35/S-thiourea, /sup 14/C-methyl iodide and /sup 35/S-thiourea, respectively, for use in studies on the mechanism of action of antithyroid drugs. The products were purified by chromatography on silica and isolated with radiochemical purities of greater than 98%, yields of 45-77% and specific activities of 2.1-5.3 mCi/mmole.

Theoretical study of the Cs isotope exchange reaction of CsI + Cs' → Cs + ICs' (Contract research)

International Nuclear Information System (INIS)

Kobayashi, Takanori; Hashimoto, Masashi; Yokoyama, Keiichi

2015-12-01

To discuss the exchange reaction of Cs isotope by CsI + Cs' → Cs + ICs', the structure and chemical properties of Cs 2 I intermediate and potential energy surface of the entrance reaction are calculated using M06/def2-TZVPPD density functional calculation. The calculation shows that the reaction to the intermediate has no barrier and the two Cs-I bonds of Cs 2 I are chemically equivalent. These results suggest that the rate of the Cs exchange reaction of CsI + Cs' → Cs + ICs' is as high as the collision rate. (author)

Performance Analysis of Communications under Energy Harvesting Constraints with noisy CSI

KAUST Repository

Znaidi, Mohamed Ridha; Rezki, Zouheir; Tembine, Hamidou; Alouini, Mohamed-Slim

2016-01-01

to environmental changes. In this work, we consider the problem of power allocation taking into account the energy arrivals over time and the degree of channel state information (CSI) available at the transmitter, to maximize the throughput. Differently from

Pro visual C++/CLI and the net 35 platform

CERN Document Server

Fraser, Stephen

2008-01-01

Pro Visual C++/CLI and the .NET 3.5 Platform is about writing .NET applications using C++/CLI. While readers are learning the ins and outs of .NET application development, they will also be learning the syntax of C++, both old and new to .NET. Readers will also gain a good understanding of the .NET architecture. This is truly a .NET book applying C++ as its development language not another C++ syntax book that happens to cover .NET.

Clinical application of 1H-chemical-shift imaging (CSI) to brain diseases

International Nuclear Information System (INIS)

Naruse, Shoji; Furuya, Seiichi; Ide, Mariko

1992-01-01

An H-1 chemical shift imaging (CSI) was developed as part of the clinical MRI system, by which magnetic resonance spectra (MRS) can be obtained from multiple small voxels and metabolite distribution in the brain can be visualized. The present study was to determine the feasibility and clinical potential of using an H-1 CSI. The device used was a Magnetom H 15 apparatus. The study population was comprised of 25 healthy subjects, 20 patients with brain tumor, 4 with ischemic disease, and 6 with miscellaneous degenerative disease. The H-1 CSI was obtained by the 3-dimensional Fourier transformation. After suppressing the lipid signal by the inversion-recovery method and the water signal by the chemical-shift selective pulse with a following dephasing gradient, 2-directional 16 x 16 phase encodings were applied to the 16 x 16∼18 x 18 cm field of view, in which a 8 x 8 x 2∼10 x 10 x 2 cm area was selected by the stimulated echo or spin-echo method. The metabolite mapping and its contour mapping were created by using the curve-fitted area, with interpolation to the 256 x 256 matrix. In the healthy group, high resolution spectra for N-acetyl aspartate (NAA), creatine, choline (Cho), and glutamine/glutamate were obtained from each voxel; and metabolite mapping and contour mapping also clearly showed metabolite distribution in the brain. In the group of brain tumor, an increased Cho and lactate and loss of NAA were observed, along with heterogeneity within the tumor and changes in the surrounding tissue; and there was a good correlation between lactate peak and tumor malignancy. The group of ischemic and degenerative disease had a decreased NAA and increased lactate on both spectra and metabolite mapping, depending on disease stage. These findings indicated that H-1 CSI is helpful for detecting spectra over the whole brain, as well as for determining metabolite distribution. (N.K.)

Modified Grid-Connected CSI for Hybrid PV/Wind Power Generation System

Directory of Open Access Journals (Sweden)

D. Amorndechaphon

2012-01-01

Full Text Available The principle of a power conditioning unit for hybrid PV/wind power generation system is proposed. The proposed power conditioner is based on the current source inverter (CSI topology. All energy sources are connected in parallel with a DC-bus through the modified wave-shaping circuits. To achieve the unity power factor at the utility grid, the DC-link current can be controlled via the wave-shaping circuits with the sinusoidal PWM scheme. In this work, the carrier-based PWM scheme is also proposed to minimize the utility current THD. The power rating of the proposed system can be increased by connecting more PV/wind modules through their wave-shaping circuits in parallel with the other modules. The details of the operating principles, the system configurations, and the design considerations are described. The effectiveness of the proposed CSI is demonstrated by simulation results.

Mechanically Stacked Dual-Junction and Triple-Junction III-V/Si-IBC Cells with Efficiencies Exceeding 31.5% and 35.4%: Preprint

Energy Technology Data Exchange (ETDEWEB)

Schnabel, Manuel [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Tamboli, Adele C [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Warren, Emily L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Schulte-Huxel, Henning [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Klein, Talysa [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Van Hest, Marinus F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Geisz, John F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Stradins, Paul [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Steiner, Myles A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rienaecker, Michael [Institute for Solar Energy Research Hamelin (ISFH); Merkle, Agnes [Institute for Solar Energy Research Hamelin (ISFH); Kajari-Schroeder, S. [Institute for Solar Energy Research Hamelin (ISFH); Niepelt, Raphael [Institute for Solar Energy Research Hamelin (ISFH); Schmidt, Jan [Institute for Solar Energy Research Hamelin (ISFH); Leibniz Universitat Hannover; Brendel, Rolf [Institute for Solar Energy Research Hamelin (ISFH); Leibniz Universitat Hannover; Peibst, Robby [Institute for Solar Energy Research Hamelin (ISFH); Leibniz Universitat Hannover

2017-10-02

Despite steady advancements in the efficiency of crystalline Silicon (c-Si) photovoltaics (PV) within the last decades, the theoretical efficiency limit of 29.4 percent depicts an insurmountable barrier for silicon-based single-junction solar cells. Combining the Si cell with a second absorber material on top in a dual junction tandem or triple junction solar cell is an attractive option to surpass this limit significantly. We demonstrate a mechanically stacked GaInP/Si dual-junction cell with an in-house measured efficiency of 31.5 percent and a GaInP/GaAs/Si triple-junction cell with a certified efficiency of 35.4 percent.

Chemical Shift Imaging (CSI) by precise object displacement

OpenAIRE

Leclerc, Sebastien; Trausch, Gregory; Cordier, Benoit; Grandclaude, Denis; Retournard, Alain; Fraissard, Jacques; Canet, Daniel

2006-01-01

International audience; A mechanical device (NMR lift) has been built for displacing vertically an object (typically a NMR sample tube) inside the NMR probe with an accuracy of 1 Μm. A series of single pulse experiments are performed for incremented vertical positions of the sample. With a sufficiently spatially selective rf field, one obtains chemical shift information along the displacement direction (one dimensional Chemical Shift Imaging – CSI). Knowing the vertical radio-frequency (rf) f...

Diffusion of Na(I), Cs(I), Sr(II) and Eu(III) in smectite rich natural clay.

Science.gov (United States)

Kasar, Sharayu; Kumar, Sumit; Bajpai, R K; Tomar, B S

2016-01-01

Diffusion of Na(I), Cs(I), Sr(II) and Eu(III) in smectite rich natural clay, proposed as a backfill material in the Indian geological repository, was studied using the out-diffusion method. Radiotracers (22)Na, (137)Cs, (85)Sr and (154)Eu were used; the first three are carrier-free enabling experimental work at sub-micromolar metal ion concentration, and Eu(III) tracer (154)Eu was used at sub millimolar concentration. An out-diffusion methodology, wherein a thin planar source of radioactivity placed between two clay columns diffuses out, was used to obtain the apparent diffusion coefficient (Da) values. This methodology enabled determination of diffusion coefficient even for strongly sorbing (154)Eu. Da values for (22)Na, (137)Cs, (85)Sr and (154)Eu were 2.35 (±0.14) × 10(-11), 2.65 (±0.09) × 10(-12), 3.32 (±0.15) × 10(-11) and 1.23 (±0.15) × 10(-13) m(2) s(-1), respectively. Da values were found to be in fair agreement with literature data reported for similar mineralogical sediments. Sorption of radionuclides on the clay was also determined in the present study and differences in Da values were rationalized on the basis of sorption data. Distribution ratios (Kd) for Cs(I) and Eu(III) were higher than that for Sr(II), which in turn was higher than that for Na(I). Copyright © 2015 Elsevier Ltd. All rights reserved.

An analysis of the sectorial influence of CSI300 stocks within the directed network

Science.gov (United States)

Mai, Yong; Chen, Huan; Meng, Lei

2014-02-01

This paper uses the Partial Correlation Planar maximally filtered Graph (PCPG) method to construct a directed network for the constituent stocks underlying the China Securities Index 300 (CSI300). We also analyse the impact of individual stocks. We find that the CSI300 market is a scale-free network with a relatively small power law exponent. The volatility of the stock prices has significant impact on other stocks. In the sectorial network, the industrial sector is the most influential one over other sectors, the financial sector only has a modest influence, while the telecommunication services sector’s influence is marginal. In addition, such inter-sector influence displays quarterly stability.

Rötning av avloppsslam vid 35, 55 och 60 °C

DEFF Research Database (Denmark)

Kjerstadius, Hamse; la Cour Jansen, Jes; Stålhandske, Liselotte

The study evaluated effect of anaerobic digestion (35, 55 and 60 °C ) at different minimum exposure times as well as from pasteurization on hygienization of pathogens, biogas production and removal of pharmaceutical substances and PAH.......The study evaluated effect of anaerobic digestion (35, 55 and 60 °C ) at different minimum exposure times as well as from pasteurization on hygienization of pathogens, biogas production and removal of pharmaceutical substances and PAH....

Immobilized nickel hexacyanoferrate on activated carbons for efficient attenuation of radio toxic Cs(I) from aqueous solutions

International Nuclear Information System (INIS)

Lalhmunsiama; Lalhriatpuia, C.; Tiwari, Diwakar; Lee, Seung-Mok

2014-01-01

Highlights: • Rice hulls and areca nut wastes are utilized to obtain activated carbons. • Nickel hexacyanoferrate is immobilized on activated carbon samples. • Materials are characterized by SEM–EDX and XRD data. • Materials are employed in attenuation of Cs(I) under batch and column studies. • Possible mechanism is deduced at solid/solution interface. - Abstract: The aim of this study is to immobilize nickel hexacyanoferrate onto the large surface of activated carbons (ACs) precursor to rice hulls and areca nut waste materials. These nickel hexacyanoferrate immobilized materials are then assessed in the effective attenuation of radio logically important cesium ions from aqueous solutions. The solid samples are characterized by the XRD analytical method and surface morphology is obtained from the SEM images. The batch reactor experiments show that an increase in sorptive pH (2.0–10.0) apparently not affecting the high percent uptake of Cs(I). Equilibrium modeling studies suggest that the data are reasonably and relatively fitted well to the Langmuir adsorption isotherm. Kinetic studies show that sorption process is fairly rapid and the kinetic data are fitted well to the pseudo-second order rate model. Increasing the background electrolyte concentration from 0.001 to 0.1 mol/L NaCl causes insignificant decrease in Cs(I) removal which infers the higher selectivity of these materials for Cs(I) from aqueous solutions. Further, the column reactor operations enable to obtain the breakthrough data which are then fitted to the Thomas non-linear equation as to obtain the loading capacity of column for Cs(I). The results show that the modified materials show potential applicability in the attenuation of radio toxic cesium from aqueous solution

Film Cooled Recession of SiC/SiC Ceramic Matrix Composites: Test Development, CFD Modeling and Experimental Observations

Science.gov (United States)

Zhu, Dongming; Sakowski, Barbara A.; Fisher, Caleb

2014-01-01

SiCSiC ceramic matrix composites (CMCs) systems will play a crucial role in next generation turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures, reduce engine weight and cooling requirements. However, the environmental stability of Si-based ceramics in high pressure, high velocity turbine engine combustion environment is of major concern. The water vapor containing combustion gas leads to accelerated oxidation and corrosion of the SiC based ceramics due to the water vapor reactions with silica (SiO2) scales forming non-protective volatile hydroxide species, resulting in recession of the ceramic components. Although environmental barrier coatings are being developed to help protect the CMC components, there is a need to better understand the fundamental recession behavior of in more realistic cooled engine component environments.In this paper, we describe a comprehensive film cooled high pressure burner rig based testing approach, by using standardized film cooled SiCSiC disc test specimen configurations. The SiCSiC specimens were designed for implementing the burner rig testing in turbine engine relevant combustion environments, obtaining generic film cooled recession rate data under the combustion water vapor conditions, and helping developing the Computational Fluid Dynamics (CFD) film cooled models and performing model validation. Factors affecting the film cooled recession such as temperature, water vapor concentration, combustion gas velocity, and pressure are particularly investigated and modeled, and compared with impingement cooling only recession data in similar combustion flow environments. The experimental and modeling work will help predict the SiCSiC CMC recession behavior, and developing durable CMC systems in complex turbine engine operating conditions.

The Mu2e undoped CsI crystal calorimeter

Science.gov (United States)

Atanov, N.; Baranov, V.; Budagov, J.; Cervelli, F.; Colao, F.; Cordelli, M.; Corradi, G.; Davydov, Y. I.; Di Falco, S.; Diociaiuti, E.; Donati, S.; Donghia, R.; Echenard, B.; Giovannella, S.; Glagolev, V.; Grancagnolo, F.; Happacher, F.; Hitlin, D. G.; Martini, M.; Miscetti, S.; Miyashita, T.; Morescalchi, L.; Murat, P.; Pedreschi, E.; Pezzullo, G.; Porter, F.; Raffaelli, F.; Ricci, M.; Saputi, A.; Sarra, I.; Spinella, F.; Tassielli, G.; Tereshchenko, V.; Usubov, Z.; Zhu, R. Y.

2018-02-01

The Mu2e experiment at Fermilab will search for Charged Lepton Flavor Violating conversion of a muon to an electron in an atomic field. The Mu2e detector is composed of a tracker, an electromagnetic calorimeter and an external system, surrounding the solenoid, to veto cosmic rays. The calorimeter plays an important role to provide: a) excellent particle identification capabilities; b) a fast trigger filter; c) an easier tracker track reconstruction. Two disks, located downstream of the tracker, contain 674 pure CsI crystals each. Each crystal is read out by two arrays of UV-extended SiPMs. The choice of the crystals and SiPMs has been finalized after a thorough test campaign. A first small scale prototype consisting of 51 crystals and 102 SiPM arrays has been exposed to an electron beam at the BTF (Beam Test Facility) in Frascati. Although the readout electronics were not final, results show that the current design is able to meet the timing and energy resolution required by the Mu2e experiment.

On the Secrecy Capacity Region of the Block-Fading BCC with Limited CSI Feedback

KAUST Repository

Hyadi, Amal

2017-02-07

In this work, we examine the secrecy capacity region of the block-fading broadcast channel with confidential messages (BCC) when the transmitter has limited knowledge of the channel. In particular, we consider a two-user communication system where the transmitter has one common message to be transmitted to both users and one confidential message intended to only one of them. The confidential message has to be kept secret from the other user to whom the information is not intended. The transmitter is not aware of the channel state information (CSI) of neither channel and is only provided by limited CSI feedback sent at the beginning of each fading block. Assuming an error-free feedback link, we characterize the secrecy capacity region of this channel and show that even with a 1-bit CSI feedback, a positive secrecy rate can still be achieved. Then, we look at the case where the feedback link is not error- free and is rather a binary erasure channel (BEC). In the latter case, we provide an achievable secrecy rate region and show that as long as the erasure event is not a probability 1 event, the transmitter can still transmit the confidential information with a positive secrecy rate.

Impact of organic overlayers on a-Si:H/c-Si surface potential

KAUST Repository

Seif, Johannes P.

2017-04-11

Bilayers of intrinsic and doped hydrogenated amorphous silicon, deposited on crystalline silicon (c-Si) surfaces, simultaneously provide contact passivation and carrier collection in silicon heterojunction solar cells. Recently, we have shown that the presence of overlaying transparent conductive oxides can significantly affect the c-Si surface potential induced by these amorphous silicon stacks. Specifically, deposition on the hole-collecting bilayers can result in an undesired weakening of contact passivation, thereby lowering the achievable fill factor in a finished device. We test here a variety of organic semiconductors of different doping levels, overlaying hydrogenated amorphous silicon layers and silicon-based hole collectors, to mitigate this effect. We find that these materials enhance the c-Si surface potential, leading to increased implied fill factors. This opens opportunities for improved device performance.

Impact of organic overlayers on a-Si:H/c-Si surface potential

KAUST Repository

Seif, Johannes P.; Niesen, Bjoern; Tomasi, Andrea; Ballif, Christophe; De Wolf, Stefaan

2017-01-01

Bilayers of intrinsic and doped hydrogenated amorphous silicon, deposited on crystalline silicon (c-Si) surfaces, simultaneously provide contact passivation and carrier collection in silicon heterojunction solar cells. Recently, we have shown that the presence of overlaying transparent conductive oxides can significantly affect the c-Si surface potential induced by these amorphous silicon stacks. Specifically, deposition on the hole-collecting bilayers can result in an undesired weakening of contact passivation, thereby lowering the achievable fill factor in a finished device. We test here a variety of organic semiconductors of different doping levels, overlaying hydrogenated amorphous silicon layers and silicon-based hole collectors, to mitigate this effect. We find that these materials enhance the c-Si surface potential, leading to increased implied fill factors. This opens opportunities for improved device performance.

Lowest instrumented vertebra selection in Lenke 3C and 6C scoliosis

DEFF Research Database (Denmark)

Wang, Yu; Bünger, Cody; Zhang, Yanqun

2012-01-01

PURPOSE: The aim of this study was to investigate whether or not post-op curve behaviour differs due to different choices of lowest instrumented vertebra (LIV) with reference to lumbar apical vertebra (LAV) in Lenke 3C and 6C scoliosis. METHODS: We reviewed all the AIS cases surgically treated...... it can yield similar correction while preserving more lumbar mobility and growth potential....

Biosorption of Cd(II) and Cs(I) from aqueous solution by live and dead cells of Saccharomyces carlsbergensis PTCC 5051.

Science.gov (United States)

Sayyadi, Shayan; Ahmady-Asbchin, Salman; Kamali, Kasra

2018-02-01

The biosorption characteristics of Cd(II) and Cs(I) using live and dead cells of Saccharomyces carlsbergensis PTCC 5051 as biosorbents have been investigated in the present research. The influence of different experimental parameters such as initial pH (pHi), shaking rate, sorption time and initial metal concentration was evaluated. The optimum pH was obtained as 4 for Cd(II) and 7 for Cs(I). The experimental adsorption data were fitted to the Langmuir linear equation adsorption model. The highest metal uptake values of 0.593 and 0.473 mmol g -1 were calculated for Cd(II) and Cs(I), respectively. The results of Fourier transform infrared analysis suggested the involvement of amine, carboxyl and hydroxyl groups during the biosorption process and also indicated that more functional groups were involved in the biosorption process of live adsorbents, compared with those linked to dead biomass. The results showed that the biomass of S. carlsbergensis PTCC 5051 is a suitable biosorbent for the removal of Cd(II) and Cs(I) from the aqueous solutions.

Characteristics of Pb{sup 2+} doped CsI matrix under gamma and neutron excitations

Energy Technology Data Exchange (ETDEWEB)

Pereira, Maria da Conceição Costa; Madi Filho, Tufic; Berretta, José Roberto; Tomaz, Lucas Faustino; Pinto, Marlene Cristina, E-mail: macoper@ipen.br, E-mail: tmfilho@ipen.br, E-mail: jrretta@ipen.br, E-mail: lucasfaus@gmail.com, E-mail: tynapinto@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2017-07-01

In recent years, there has been an increasing interest in finding new fast scintillating material or improve the characteristics of known scintillators for the demand of high energy physics, industrial and nuclear medical applications. Ions divalent lead Pb{sup 2+} built in some crystal structures are efficient emission centers and their applications in scintillators was and still is the reason of an intensive study of emission properties of different compounds containing these ions. The aggregation of impurities in CsI is poorly studied. The problem of impurity aggregation in CsI is of interest from point of view of the luminescent properties modification of this scintillation material. In this context, the crystals of Pb{sup 2+} doped CsI matrix were grown by the vertical Bridgman technique and subjected to annealing in vacuum of 10{sup -6} mbar and continuous temperature of 350°C, for 24 hours, and then they were employed. To evaluate the response of the CsI:Pb scintillator crystal to gamma radiation, radioactive sources of {sup 137}Cs (662 keV), {sup 60}Co (1173 keV and 1333 keV), {sup 22}Na (511 keV and 1275 keV) and {sup 13}3Ba (355 keV) was used. The operating voltage of the photomultiplier was 2700 V for the detection of gamma rays and the accumulation time in the counting process was 600 s. The crystals used in gamma spectroscopy were cut with dimensions of 20 mm in diameter and 20 mm in height. The scintillator response to neutron radiation from a radioactive source of Am/Be with energy range of 1 MeV to 12 MeV was available. The activity of the AmBe source was 1Ci Am. The fluency was 2.6 x 10{sup 6} neutrons / second. The operating voltage of the photomultiplier tube was 1300 V. The accumulation time in the counting process was 600 s. The scintillator crystals were cut with dimensions of 20 mm diameter and 10 mm height. With the results obtained, it may be observed that the crystals are sensitive to these radiations. (author)

Achievable Rates of Cognitive Radio Networks Using Multi-Layer Coding with Limited CSI

KAUST Repository

Sboui, Lokman; Rezki, Zouheir; Alouini, Mohamed-Slim

2016-01-01

In a Cognitive Radio (CR) framework, the channel state information (CSI) feedback to the secondary transmitter (SU Tx) can be limited or unavailable. Thus, the statistical model is adopted in order to determine the system performance using

Opportunistic Energy-Aware Amplify-and-Forward Cooperative Systems with Imperfect CSI

KAUST Repository

Amin, Osama

2015-07-29

Recently, much attention has been paid to the green design of wireless communication systems using energy efficiency (EE) metrics that should capture all energy consumption sources to deliver the required data. In this paper, we design an energyefficient relay assisted communication system based on estimated channel state information (CSI). It employs amplify-andforward relaying and switches between different communication schemes, which are known as direct-transmission, two-hop and cooperative-transmission schemes, using the estimated CSI in order to maximize the EE. Two estimation strategies are assumed, namely disintegrated channel estimation and cascaded channel estimation. To formulate an accurate EE metric for the proposed opportunistic amplify-and-forward system, the channel estimation cost is reflected on the EE metric by including its impact in the signal-to-noise ratio term and in the energy consumption during the channels estimation phase. Based on the formulated EE metric, we propose an adaptive power allocation algorithm to maximize the EE of the proposed opportunistic amplify-andforward system with channel estimation. Furthermore, we study the impact of the estimation parameters on the proposed system via simulation examples.

Outage Performance of Decode-and-Forward in Two-Way Relaying with Outdated CSI

KAUST Repository

Hyadi, Amal

2015-01-07

In this paper, we analyze the outage behavior of decode-and-forward relaying in the context of selective two-way cooperative systems. First, a new relay selection metric is proposed to take into consideration both transmission rates and instantaneous link conditions between cooperating nodes. Afterwards, the outage probability of the proposed system is derived for Nakagami-m fading channels in the case when perfect channel state information is available and then extended to the more realistic scenario where the available channel state information (CSI) is outdated due to fast fading. New expressions for the outage probability are obtained, and the impact of imperfect CSI on the performance is evaluated. Illustrative numerical results, Monte Carlo simulations, and comparisons with similar approaches are presented to assess the accuracy of our analytical derivations and confirm the performance gain of the proposed scheme.

17 bit 4.35 mW 1 kHz Delta Sigma ADC and 256-to-1 multiplexer for remote handling instrumentation equipment

Energy Technology Data Exchange (ETDEWEB)

Verbeeck, Jens, E-mail: jens.verbeeck@esat.kuleuven.be [KU Leuven, Department ESAT-MICAS, Kasteelpark Arenberg 10, 3001 Heverlee (Belgium); KH Kempen University College, IBW-RELIC, Kleinhoefstraat 4, 2440 Geel (Belgium); Van Uffelen, Marco [Fusion for Energy, c/Josep, n° 2, Torres Diagonal Litoral, Ed. B3, 08019 Barcelona (Spain); Steyaert, Michiel [KU Leuven, Department ESAT-MICAS, Kasteelpark Arenberg 10, 3001 Heverlee (Belgium); Leroux, Paul [KU Leuven, Department ESAT-MICAS, Kasteelpark Arenberg 10, 3001 Heverlee (Belgium); KH Kempen University College, IBW-RELIC, Kleinhoefstraat 4, 2440 Geel (Belgium)

2013-10-15

Highlights: ► We present a radiation hard 17 bit-1 kHz 4.35 mW Delta Sigma ADC. ► A radiation tolerant 256-to-1 multiplexer is shown. ► We propose a generic radiation tolerant ASIC for use in an instrumentation link. ► The ASIC can interface more than hundred pressure or resistive sensors. ► All building blocks have a simulated radiation tolerance of more than 1 MGy. -- Abstract: A radiation tolerant Delta-Sigma Analog-to-Digital Converter (ADC) and multiplexer is presented. The design features a 1.5 V, 17 bit ADC consuming 4.35 mW at a sample frequency of 1 MHz. The ADC features a bandwidth of 1 kHz and utilizes a Correlated Double Sampling technique (CDS) to remove offset and 1/f noise. The circuit maintains its 17 bit resolution upon a simulated radiation dose exceeding 1 MGy and varying temperatures between 0 °C and 85 °C. Next a multiplexer is presented. It can multiplex 256 channels at a clock frequency of 128 MHz or has a data throughput of 256 MSample/s. In addition the bit period of the multiplexer varies less then 1.5% due to the influence of temperature or radiation, which proves the temperature and radiation tolerance.

Minimax robust power split in AF relays based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish; Alouini, Mohamed-Slim

2011-01-01

An optimal power control among source and relay nodes in presence of channel state information (CSI) is vital for an efficient amplify and forward (AF) based cooperative communication system. In this work, we study the optimal power split (power

Non-Identity-Mediated CRISPR-Bacteriophage Interaction Mediated via the Csy and Cas3 Proteins ▿#

Science.gov (United States)

Cady, Kyle C.; O'Toole, George A.

2011-01-01

Studies of the Escherichia, Neisseria, Thermotoga, and Mycobacteria clustered regularly interspaced short palindromic repeat (CRISPR) subtypes have resulted in a model whereby CRISPRs function as a defense system against bacteriophage infection and conjugative plasmid transfer. In contrast, we previously showed that the Yersinia-subtype CRISPR region of Pseudomonas aeruginosa strain UCBPP-PA14 plays no detectable role in viral immunity but instead is required for bacteriophage DMS3-dependent inhibition of biofilm formation by P. aeruginosa. The goal of this study is to define the components of the Yersinia-subtype CRISPR region required to mediate this bacteriophage-host interaction. We show that the Yersinia-subtype-specific CRISPR-associated (Cas) proteins Csy4 and Csy2 are essential for small CRISPR RNA (crRNA) production in vivo, while the Csy1 and Csy3 proteins are not absolutely required for production of these small RNAs. Further, we present evidence that the core Cas protein Cas3 functions downstream of small crRNA production and that this protein requires functional HD (predicted phosphohydrolase) and DEXD/H (predicted helicase) domains to suppress biofilm formation in DMS3 lysogens. We also determined that only spacer 1, which is not identical to any region of the DMS3 genome, mediates the CRISPR-dependent loss of biofilm formation. Our evidence suggests that gene 42 of phage DMS3 (DMS3-42) is targeted by CRISPR2 spacer 1 and that this targeting tolerates multiple point mutations between the spacer and DMS3-42 target sequence. This work demonstrates how the interaction between P. aeruginosa strain UCBPP-PA14 and bacteriophage DMS3 can be used to further our understanding of the diverse roles of CRISPR system function in bacteria. PMID:21398535

From a sociology of mediation to a pragmatics of attachments. An intellectual journey within the CSI revisited

OpenAIRE

Hennion, Antoine

2017-01-01

Este artículo enfoca sobre un retorno reflexivo en mi propia trayectoria en el CSI. Mi propósito no es fijar la historia sino releerla desde las preocupaciones presentes. Desde su fundación por L. Karpik en 1967, el CSI abogó por tomar seriamente las realidades que estaba investigando (derecho, ciencia y tecnología, negocios, cultura). Bajo el título de un posible “retorno al objeto” en sociología, discuto convergencias y diferencias en el trabajo de campo emprendido, por un lado, sobre la ci...

Characterization of Material from Wells 299-W10-35 (C7573) and 299-W14-74 (C7024)

International Nuclear Information System (INIS)

Tilton, Fred A.; Wellman, Dawn M.; Bovaird, Chase C.; Strandquist, Sara C.

2011-01-01

The objective of this work was to characterize material accumulating on wells 299-W10-35 (C7573) and 299-W14-74 (C7024) to determine the type of material (i.e., chemical or biological) and, if the material is biological, to identify the microorganisms present. Extraction and injection wells 299-W10-35 (C7573) and 299-W14-74 (C7024) possess unknown material attached to the well screens (Figure 1). Both wells are located on the Hanford Site. Well 299-W10-35 (C7573) is located west of the 218-W-3A dry waste burial ground, west of Dayton Avenue, and north of 23rd Street and has accumulated white material on the screen and in the sump. Well 299-W14-74 (C7024) is located south of 23rd Street and east of Beloit Avenue. There are two types of material: one is reddish/orange (hypothesized to be iron-utilizing bacterial colonies) and the other is white and may or may not be biological. CH2M HILL Plateau Remediation Company (CHPRC) is conducting onsite sampling for total organic carbon, calcium carbonate, and metals. Table 1 presents chemical data for the groundwater samples associated with these materials. The objective of this work was to characterize material accumulating on wells 299-W10-35 (C7573) and 299-W14-74 (C7024) to determine the type of material (i.e., chemical or biological), and if the material is biological, to identify the microorganisms present.

Luminescent properties of BaCl2-Eu microcrystals embedded in a CsI matrix

International Nuclear Information System (INIS)

Pushak, A.; Vistovskyy, V.; Voloshinovskii, A.; Savchyn, P.; Antonyak, O.; Demkiv, T.; Dacyuk, Yu.; Myagkota, S.; Gektin, A.

2013-01-01

The spectral-luminescent properties of CsI-BaCl 2 (1 mol%)-Eu(0.02 mol%) crystalline system are studied. Europium ion doped BaCl 2 microcrystals embedded in a CsI matrix are revealed on CsI-BaCl 2 (1 mol%)-Eu(0.02 mol%) freshly cleaved surface by the scanning electron microscopy. The size of microcrystals is shown to be within 0.5–5 microns. The luminescent parameters of the BaCl 2 -Eu 2+ microcrystals are shown to be similar to ones of a single crystal analogue. The 4f → 5d absorption transitions in europium ions and the reabsorption of the intrinsic emission of the CsI host are the main excitation mechanisms of europium luminescence in the BaCl 2 microcrystals. -- Highlights: ► The formation of chloride BaCl 2 :Eu microcrystals in the case of BaCl 2 doped CsI crystal has been revealed. ► The observed size of microcrystals at BaCl 2 concentration of 1% is about 0.5–5 μm. ► Majority of Eu 2+ ions in CsI-BaCl 2 -EuCl 3 crystalline system enters into BaCl 2 microcrystals. ► The luminescent parameters of the BaCl 2 :Eu 2+ microcrystals and its bulk analogue are similar

Impact of I/Q imbalance on the performance of two-way CSI-assisted AF relaying

KAUST Repository

Qi, Jian; Aï ssa, Sonia; Alouini, Mohamed-Slim

2013-01-01

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-and-forward (AF) relaying in the presence of in-phase and quadrature-phase (I/Q) imbalance. A compensation approach for the I/Q imbalance is proposed, which employs the received signals together with their conjugations to detect the desired signal. We also derive the average symbol error probability of the considered half-duplex two-way dual-hop CSI-assisted AF relaying networks with and without compensation for I/Q imbalance in Rayleigh fading channels. Numerical results are provided and show that the proposed compensation method mitigates the impact of I/Q imbalance to a certain extent. © 2013 IEEE.

Impact of I/Q imbalance on the performance of two-way CSI-assisted AF relaying

KAUST Repository

Qi, Jian

2013-04-01

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-and-forward (AF) relaying in the presence of in-phase and quadrature-phase (I/Q) imbalance. A compensation approach for the I/Q imbalance is proposed, which employs the received signals together with their conjugations to detect the desired signal. We also derive the average symbol error probability of the considered half-duplex two-way dual-hop CSI-assisted AF relaying networks with and without compensation for I/Q imbalance in Rayleigh fading channels. Numerical results are provided and show that the proposed compensation method mitigates the impact of I/Q imbalance to a certain extent. © 2013 IEEE.

Synthesis of organic substances labelled with 14C and 35S

International Nuclear Information System (INIS)

Pichat, L.

1958-01-01

After a brief history of the development of the Section des Molecules marquees of the French Atomic Energy Commission, the author gives an outline of the synthesis of the following labelled compounds: benzene 14 C-6; phenyl-p-fluorophenyl, thienyl-2 β alanines β 14 C; noradrenaline β 14 C (arterenol β 14 C), dotriacontane 14 C-16-17, aminoethane sulfinic acid (hypotaurine 35 S). (author) [fr

40 CFR 60.35c - Reporting and recordkeeping guidelines.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Reporting and recordkeeping guidelines... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Municipal Solid Waste Landfills § 60.35c Reporting and recordkeeping guidelines. For approval...

Enhanced columnar structure in CsI layer by substrate patterning

Energy Technology Data Exchange (ETDEWEB)

Jing, T.; Cho, G.; Drewery, J.; Kaplan, S.N.; Mireshghi, A.; Perez-Mendez, V.; Wildermuth, D. [Lawrence Berkeley Lab., CA (United States); Fujieda, I. [Xerox Palo Alto Research Center, CA (United States)

1991-10-01

Columnar structure in evaporated CsI layers can be controlled by patterning substrates as well as varying evaporation conditions. Mesh-patterned substrates with various dimensions were created by spin-coating polyimide on glass or amorphous silicon substrates and defining patterns with standard photolithography technique. CsI(Tl) layers 200--1000 {mu}m were evaporated. Scintillation properties of these evaporated layers, such as light yield and speed, were equivalent to those of the source materials. Spatial resolution of X-ray detectors consisting of these layers and a linear array of X-ray detectors consisting of these layers and a linear array of Si photodiodes was evaluated by exposing them to a 25{mu}m narrow beam of X-ray. The results obtained with 200{mu}m thick CsI layers coupled to a linear photodiode array with 20 dots/mm resolution showed that the spatial resolution of CsI(Tl) evaporated on patterned substrates was about 75 {mu}m FWHM, whereas that on CsI(Tl) on flat substrates was about 230 {mu}m FWHM. Micrographs taken by SEM revealed that these layers retained the well-defined columnar structure originating from substrate patterns. Adhesion and light transmission of CsI(Tl) were also improved by patterning the substrate.

35Cl + 12C asymmetrical fission excitation functions

International Nuclear Information System (INIS)

Beck, C.; Mahboub, D.; Nouicer, R.; Freeman, R.M.; Haas, F.; Youlal, M.; Matsuse, T.; Sanders, S.J.

1996-04-01

The fully energy-damped yields from the 35 Cl + 12 C reaction have been systematically investigated using particle-particle coincidence techniques at a 35 Cl bombarding energy of ∼ 8 MeV/nucleon. The fragment-fragment correlation data show that the majority of events arises from a binary-decay process with rather large numbers of secondary light-charged particles emitted from the two excited exit fragments. No evidence is observed for ternary breakup events. The binary-process results of the present measurement, along with those of earlier, inclusive experimental data obtained at several lower bombarding energies are compared with predictions of two different kinds of statistical model calculations. The methods give comparable predictions and are both in good agreement with the experimental results thus confirming the fusion-fission origin of the fully-damped yields. (author)

Study of a pure CsI crystal readout by APD for Belle II end cap ECL upgrade

Energy Technology Data Exchange (ETDEWEB)

Jin, Y., E-mail: jin@hep.phys.s.u-tokyo.ac.jp [Department of Physics, the University of Tokyo, 7-3-1 Hongo Bunkyo-ku, Tokyo 113-0033 (Japan); Aihara, H. [Department of Physics, the University of Tokyo, 7-3-1 Hongo Bunkyo-ku, Tokyo 113-0033 (Japan); Borshchev, O.V. [Enikolopov Institute of Synthetic Polymeric Materials of the Russian Academy of Sciences, Profsoyuznaya st. 70, Moscow 117393 (Russian Federation); Epifanov, D.A. [Department of Physics, the University of Tokyo, 7-3-1 Hongo Bunkyo-ku, Tokyo 113-0033 (Japan); Ponomarenko, S.A.; Surin, N.M. [Enikolopov Institute of Synthetic Polymeric Materials of the Russian Academy of Sciences, Profsoyuznaya st. 70, Moscow 117393 (Russian Federation)

2016-07-11

A scintillation counter consisting of a pure CsI crystal and avalanche photodiodes (Hamamatsu APD S8664-55 and S8664-1010) has been studied for the upgrade of the end cap electromagnetic calorimeter of Belle II detector. An essential increase of the light output was achieved with wavelength shifters based on nanostructured organosilicon luminophores. - Highlights: • A scintillation counter consisting of a pure CsI crystal and avalanche photodiodes has been studied. • The equivalent noise charge and equivalent noise energy of the counter have been measured. • An essential increase of the light output was achieved with wavelength shifters.

Comparison of shipping, handling, and shock instrumentation results for two 3.5-m-class primary mirrors

Science.gov (United States)

Killpatrick, Don H.; Mayo, James W.

1998-08-01

Packing, shipping, and handling procedures employed during several transportation activities for two large telescope primary mirrors are presented along with detailed shock recording results. Operations monitored included craning, forklifting, and shipping by air, sea, and land during all phases of manufacture and installation. The mirrors monitored were the SOR 3.5-m Telescope spun cast borosilicate primary mirror and the AEOS 3.67-m Telescope Zerodur thin meniscus primary mirror. Shock recording instrumentation included 2-, 5-, and 10-g Omni-G(superscript TM) impact indicators, 10-g Impact o-graph(superscript TM) 3-axis recording accelerometers, and high-resolution 3-axis accelerometers with Astromed Dash 8 eight-channel chart recorders and audio indicators. Shock results for some operations were monitored to the 0.01-g level. In-shipment temperature data are also presented and discussed. Effects of lifting operations, road conditions via truck, flight conditions via C-5B aircraft, and transportation via sea- going barge are discussed. Data are presented for three different crate designs and configurations and, in some cases, include mirror-in-cell shipping data. Shock results were observed from as low as a few hundredths-g to over 3- g's during various operations.

Longitudinal uniformity, time performances and irradiation test of pure CsI crystals

Energy Technology Data Exchange (ETDEWEB)

Angelucci, M. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Atanova, O. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Baccaro, S.; Cemmi, A. [ENEA UTTMAT-IRR, Casaccia R.C., Roma (Italy); Cordelli, M. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Donghia, R., E-mail: raffaella.donghia@lnf.infn.it [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Dipartimento di Fisica, Universitá Roma Tre, Roma (Italy); Giovannella, S.; Happacher, F.; Miscetti, S.; Sarra, I.; Soleti, S.R. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy)

2016-07-11

To study an alternative to BaF{sub 2}, as the crystal choice for the Mu2e calorimeter, 13 pure CsI crystals from Opto Materials and ISMA producers have been characterized by determining their light yield (LY) and longitudinal response uniformity (LRU), when read with a UV extended PMT. The crystals show a LY of ~100 p.e./MeV (~150 p.e./MeV) when wrapped with Tyvek and coupled to the PMT without (with) optical grease. The LRU is well represented by a linear slope that is on average δ~ −0.6%/cm. The timing performances of the Opto Materials crystal, read with a UV extended MPPC, have been evaluated with minimum ionizing particles. A timing resolution of ~330 ps (~ 440 ps) is achieved when connecting the photosensor to the MPPC with (without) optical grease. The crystal radiation hardness to a ionization dose has also been studied for one pure CsI crystal from SICCAS. After exposing it to a dose of 900 Gy, a decrease of 33% in the LY is observed while the LRU remains unchanged.

49th Annual Convention of the Computer Society of India CSI

CERN Document Server

Govardhan, A; Raju, K; Mandal, J

2015-01-01

Volume 1 contains 73 papers presented at CSI 2014: Emerging ICT for Bridging the Future: Proceedings of the 49th Annual Convention of Computer Society of India. The convention was held during 12-14, December, 2014 at Hyderabad, Telangana, India. This volume contains papers mainly focused on Fuzzy Systems, Image Processing, Software Engineering, Cyber Security and Digital Forensic, E-Commerce, Big Data, Cloud Computing and ICT applications.

Innovative operating modes and techniques for the spaceborne imaging radar-C instrument

Science.gov (United States)

Huneycutt, Bryan L.

1990-01-01

The operation of the spaceborne imaging radar-C (SIR-C) is discussed. The SIR-C instrument has been designed to obtain simultaneous multifrequency and simultaneous multipolarization radar images from a low earth orbit. It is a multiparameter imaging radar which will be flown during at least two different seasons. The instrument has been designed to operate in innovative modes such as the squint alignment mode, the extended aperture mode, the scansar mode, and the interferometry mode. The instrument has been designed to demonstrate innovative engineering techniques such as beam nulling for echo tracking, pulse-repetition frquency hopping for Doppler centroid tracking, generating the frequency step chirp for radar parameter flexibility, block floating point quantizing for data rate compression, and elevation beamwidth broadening for increasing the swath illumination.

Children and Crime Scenes: Have Schools Fallen Victim to the CSI Effect?

Science.gov (United States)

Eskriett, Angela

2011-01-01

Whilst there continues to be debate regarding the influence of the "CSI effect" upon the criminal justice system, there appears to be a general consensus that the popularisation of work within the field, particularly through a number of "procedural cop shows", has fuelled an explosion in the number of young people choosing to pursue a career in…

Creep Behavior and Durability of Cracked CMC

Science.gov (United States)

Bhatt, R. T.; Fox, Dennis; Smith, Craig

2015-01-01

To understand failure mechanisms and durability of cracked Ceramic matrix composites (CMCs), Melt Infiltration (MI) SiCSiC composites with Sylramic-iBN fibers and full Chemical vapour infiltration SiCSiC composites with Sylramic-ion bombarded BN (iBN) and Hi-Nicalon -S fibers were pre-cracked between 150 to 200 megapascal and then creep and Sustained Peak Low Cycle Fatigue (SPLCF) tested at 13150 C at stress levels from 35 to 103 megapascal for up to 200 hours under furnace and burner rig conditions. In addition creep testing was also conducted on pre-cracked full Chemical vapour infiltration SiCSiC composites at 14500 C between 35 and 103 megapascal for up to 200 hours under furnace conditions. If the specimens survived the 200 hour durability tests, then they were tensile tested at room temperature to determine their residual tensile properties. The failed specimens were examined by Scanning electron microscope (SEM) to determine the failure modes and mechanisms. The influence of crack healing matrix, fiber types, crack density, testing modes and interface oxidation on durability of cracked Ceramic matrix composites (CMCs) will be discussed.

Development of large area CsI photocathodes for the Alice/Humped Rich detector

International Nuclear Information System (INIS)

Hoedlmoser, H.

2005-03-01

The work carried out within the framework of this PhD deals with the measurement of the photoelectric properties of large area thin film cesium iodide photocathodes (PCs) which are to be used as a photon converter in a proximity focusing RICH detector for High Momentum Particle Identification (HMPID) in the ALICE experiment at the LHC. The objective was to commission a VUV-scanner setup for in-situ measurements of the photoelectric response of the CsI PCs and the use of this system to investigate the properties of these photon detectors. Among the investigated phenomena the most important ones were: - Post deposition treatment: from R and D studies it was known, that the PC response can be increased by heating the PC after the coating process. Within this thesis it was shown that the enhancement effect is mandatory to achieve the photon conversion efficiency required by the detector design and that any difference in PC quality is due to differences in this enhancement effect. - Ageing effects: CsI PCs age under exposure to humidity due to the hygroscopicity of CsI and under high photon flux and ion bombardment inside the Multi Wire Proportional Chamber (MWPC) of the detector. All three effects have been investigated with the VUV scanner. The first effect requires a careful treatment of the CsI PCs to avoid exposure to humid air. Furthermore this effect was found to be reversible if the PC is heated. High photon fluxes are irrelevant in a Cherenkov detector dealing with single photons, however, the problem needed to be investigated to verify that the measurement process itself does not damage the PCs. The third mechanism is very important as it occurs during normal detector operation and depends only on the radiation environment of the experiment. For a dose corresponding to 20 years of operation inside ALICE an accelerated test showed a clear degradation of up to 40 % of the PC response. With the results of these studies the first 17 PCs (of 42) for the detector

The CSI Academy: Encouraging Diverse Students to Consider Science Careers and Science Teaching

Science.gov (United States)

Kaye, Karen; Turner, John F.; Emigh, James

2011-01-01

The CSI academies employed a multi-layered, collaborative approach to encourage diverse students to consider STEM careers, including science teaching. The academies recruited a diverse group of high school students. This was due, in large part, to the creation of a unique selection process that identified students with unrealized potential. The…

Passive hypothermia (≥35 - <36°C during transport of newborns with hypoxic-ischaemic encephalopathy.

Directory of Open Access Journals (Sweden)

Aurélie Sellam

Full Text Available Hypothermia initiated in the first six hours of life in term infants with hypoxic ischemic encephalopathy reduces the risk of death and severe neurological sequelae. Our study's principal objective was to evaluate transport predictors potentially influencing arrival in NICU (Neonatal Intensive Care Unit at a temperature ≥35-<36°C.A multi-centric, prospective cohort study was conducted during 18 months by the three Neonatal Transport Teams and 13 NICUs. Newborns were selected for inclusion according to biological and clinical criteria before transport using passive hypothermia using a target temperature of ≥35-<36°C. Data on 120 of 126 inclusions were available for analysis. Thirty-three percent of the children arrived in NICU with the target temperature of ≥35-<36°C. The mean temperature for the whole group of infants on arrival in NICU was 35.4°C (34.3-36.5. The median age of all infants on arrival in NICU was 3h03min [2h25min-3h56min]. Three infants arrived in NICU with a temperature of <33°C and eleven with a temperature ≥37°C. Adrenaline during resuscitation was associated with a lower mean temperature on arrival in NICU.Our strategy using ≥35-<36°C passive hypothermia combined with short transport times had little effect on temperature after the arrival of Neonatal Transport Team although did reduce numbers of infants arriving in NICU in deep hypothermia. For those infants where hypothermia was discontinued in NICU our strategy facilitated re-warming. Re-adjustment to a lower target temperature to ≥34.5-<35.5°C may reduce the proportion of infants with high/normothermic temperatures.

Carrier frequency of GJB2 gene mutations c.35delG, c.235delC and c.167delT among the populations of Eurasia.

Science.gov (United States)

Dzhemileva, Lilya U; Barashkov, Nikolay A; Posukh, Olga L; Khusainova, Rita I; Akhmetova, Vita L; Kutuev, Ildus A; Gilyazova, Irina R; Tadinova, Vera N; Fedorova, Sardana A; Khidiyatova, Irina M; Lobov, Simeon L; Khusnutdinova, Elza K

2010-11-01

Hearing impairment is one of the most common disorders of sensorineural function and the incidence of profound prelingual deafness is about 1 per 1000 at birth. GJB2 gene mutations make the largest contribution to hereditary hearing impairment. The spectrum and prevalence of some GJB2 mutations are known to be dependent on the ethnic origin of the population. This study presents data on the carrier frequencies of major GJB2 mutations, c.35delG, c.167delT and c.235delC, among 2308 healthy persons from 18 various populations of Eurasia: Russians, Bashkirs, Tatars, Chuvashes, Udmurts, Komi-Permyaks and Mordvins (Volga-Ural region of Russia); Belarusians and Ukrainians (East Europe); Abkhazians, Avars, Cherkessians and Ingushes (Caucasus); Kazakhs, Uighurs and Uzbeks (Central Asia); and Yakuts and Altaians (Siberia). The data on c.35delG and c.235delC mutation prevalence in the studied ethnic groups can be used to investigate the prospective founder effect in the origin and prevalence of these mutations in Eurasia and consequently in populations around the world.

Testing compound-specific δ13C of amino acids in mussels as a new approach to determine the average 13C values of primary production in littoral ecosystems

Science.gov (United States)

Vokhshoori, N. L.; Larsen, T.; McCarthy, M.

2012-12-01

Compound-specific isotope analysis of amino acids (CSI-AA) is a technique used to decouple trophic enrichment patterns from source changes at the base of the food web. With this new emerging tool, it is possible to precisely determine both trophic position and δ15N or δ13C source values in higher feeding organisms. While most work to date has focused on nitrogen (N) isotopic values, early work has suggested that δ13C CSI-AA has great potential as a new tracer both to a record δ13C values of primary production (unaltered by trophic transfers), and also to "fingerprint" specific carbon source organisms. Since essential amino acids (EAA) cannot be made de novo in metazoans but must be obtained from diet, the δ13C value of the primary producer is preserved through the food web. Therefore, the δ13C values of EAAs act as a unique signature of different primary producers and can be used to fingerprint the dominant carbon (C) source driving primary production at the base of the food web. In littoral ecosystems, such as the California Upwelling System (CUS), the likely dominant C sources of suspended particulate organic matter (POM) pool are kelp, upwelling phytoplankton or estuarine phytoplankton. While bulk isotopes of C and N are used extensively to resolve relative consumer hierarchy or shifting diet in a food web, we found that the δ13C bulk values in mussels cannot distinguish exact source in littoral ecosystems. Here we show 15 sites within the CUS, between Cape Blanco, OR and La Jolla, CA where mussels were sampled and analyzed for both bulk δ13C and CSI-AA. We found no latitudinal trends, but rather average bulk δ13C values for the entire coastal record were highly consistent (-15.7 ± 0.9‰). The bulk record would suggest either nutrient provisioning from kelp or upwelled phytoplankton, but 13C-AA fingerprinting confines these two sources to upwelling. This suggests that mussels are recording integrated coastal phytoplankton values, with the enriched �

Imaging responses of on-site CsI and Gd2O2S flat-panel detectors: Dependence on the tube voltage

Science.gov (United States)

Jeon, Hosang; Chung, Myung Jin; Youn, Seungman; Nam, Jiho; Lee, Jayoung; Park, Dahl; Kim, Wontaek; Ki, Yongkan; Kim, Ho Kyung

2015-07-01

One of the emerging issues in radiography is low-dose imaging to minimize patient's exposure. The scintillating materials employed in most indirect flat-panel detectors show a drastic change of X-ray photon absorption efficiency around their K-edge energies that consequently affects image quality. Using various tube voltages, we investigated the imaging performance of most popular scintillators: cesium iodide (CsI) and gadolinium oxysulfide (Gd2O2S). The integrated detective quantum efficiencies (iDQE) of four detectors installed in the same hospital were evaluated according to the standardized procedure IEC 62220-1 at tube voltages of 40 - 120 kVp. The iDQE values of the Gd2O2S detectors were normalized by those of CsI detectors to exclude the effects of image postprocessing. The contrast-to-noise ratios (CNR) were also evaluated by using an anthropomorphic chest phantom. The iDQE of the CsI detector outperformed that of the Gd2O2S detector over all tube voltages. Moreover, we noted that the iDQE of the Gd2O2S detectors quickly rolled off with decreasing tube voltage under 70 kVp. The CNRs of the two scintillators were similar at 120 kVp. At 60 kVp, however, the CNR of Gd2O2S was about half that of CsI. Compared to the Gd2O2S detectors, variations in the DQE performance of the CsI detectors were relatively immune to variations in the applied tube voltages. Therefore, we claim that Gd2O2S detectors are inappropriate for use in low-tube-voltage imaging (e.g., extremities and pediatrics) with low patient exposure.

Cyclic Fatigue Durability of Uncoated and EBC Coated 3D SiC/SiC Composites Under Thermal Gradient Conditions at 2700F in Air

Science.gov (United States)

Smith, Craig; Harder, Bryan; Zhu, Dongming; Bhatt, Ramakrishna; Kalluri, Sreeramesh

2017-01-01

Ceramic matrix composites (CMCs) such as SiCSiC are currently being designed and implemented in high temperature sections of aerospace turbine engines. Such components will be subject to through-thickness thermal gradients, which may affect the durability. In this study, SiCSiC CMCs with a hybrid chemical vapor infiltrated (CVI) and polymer infiltration and pyrolysis (PIP) matrix were loaded in tension while one surface was heated with a laser and the opposite surface was cooled. The samples were each coated with an environmental barrier coating (EBC), which was produced by electron beam physical deposition (EBPVD). Results for CMCs tested with and without the EBC be discussed.

Rancang Bangun Alat Ukur Kelajuan Udara Tipe Thermal Terintegrasi Termometer Udara Berbasis Sensor LM35 dan PT100

Directory of Open Access Journals (Sweden)

Laila Katriani

2017-11-01

INTEGRATED WITH AIR THERMOMETER USING  LM35 SENSOR AND PT100 SENSOR This research aimed to design a thermal type anemometer integrated with air thermometer using Lm35 sensor and PT100 sensor. The study began in Mei until Oktober 2016. The study was conducted at the Laboratory of Electronics and Instrumentation, Department of Physics Education, State University of Yogyakarta. The design of the thermal type anemometer consists of two stages, namely, the design of the hardware and software design. Hardware design consists of a sensor system design (LM35 and PT100,  LM317 design, system design for data processing and display. Software design using C language. Based on the results of tests that had been done, shows that the sensor output LM35, whic is voltage is proportional to temperature changes, which had a sensitivity of 0.009 volts / ºC and initial output voltage of the sensor when the temperature reach 0 °C is 0,041 volts. PT100 sensor output, which is resistance is proportional to temperature changes, which had sensitivity of 0.391 Ω/oC and initial output resistance of the sensor when temperature reach 28 °C is 100,8 Ω. Error percent of thermal-type air speed measuring instrument testing is 4%.

Exploring K-3 Teachers' Implementation of Comprehension Strategy Instruction (CSI) Using Expectancy-Value Theory

Science.gov (United States)

Foley, Laura S.

2011-01-01

This research investigated factors that influence the implementation levels of evidence-based comprehension strategy instruction (CSI) among K-3 teachers. An explanatory design was chosen to gather and probe the data. Quantitative data were gathered via a mailed survey distributed through a representative sample of the 40 school districts (through…

Effect Size (Cohen's d of Cognitive Screening Instruments Examined in Pragmatic Diagnostic Accuracy Studies

Directory of Open Access Journals (Sweden)

Andrew J. Larner

2014-07-01

Full Text Available Background/Aims: Many cognitive screening instruments (CSI are available to clinicians to assess cognitive function. The optimal method comparing the diagnostic utility of such tests is uncertain. The effect size (Cohen's d, calculated as the difference of the means of two groups divided by the weighted pooled standard deviations of these groups, may permit such comparisons. Methods: Datasets from five pragmatic diagnostic accuracy studies, which examined the Mini-Mental State Examination (MMSE, the Mini-Mental Parkinson (MMP, the Six-Item Cognitive Impairment Test (6CIT, the Montreal Cognitive Assessment (MoCA, the Test Your Memory test (TYM, and the Addenbrooke's Cognitive Examination-Revised (ACE-R, were analysed to calculate the effect size (Cohen's d for the diagnosis of dementia versus no dementia and for the diagnosis of mild cognitive impairment versus no dementia (subjective memory impairment. Results: The effect sizes for dementia versus no dementia diagnosis were large for all six CSI examined (range 1.59-1.87. For the diagnosis of mild cognitive impairment versus no dementia, the effect sizes ranged from medium to large (range 0.48-1.45, with MoCA having the largest effect size. Conclusion: The calculation of the effect size (Cohen's d in diagnostic accuracy studies is straightforward. The routine incorporation of effect size calculations into diagnostic accuracy studies merits consideration in order to facilitate the comparison of the relative value of CSI.

The Vector Electric Field Instrument on the C/NOFS Satellite

Science.gov (United States)

Pfaff, R.; Kujawski, J.; Uribe, P.; Bromund, K.; Fourre, R.; Acuna, M.; Le, G.; Farrell, W.; Holzworth, R.; McCarthy, M.;

Simulation calculations of efficiencies and silicon consumption for CH3NH3PbI3−x−y Brx Cly/crystalline silicon tandem solar cells

International Nuclear Information System (INIS)

Zhang, Lili; Xie, Ziang; Qin, Guogang; Tian, Fuyang

2017-01-01

Much attention has been paid to two-subcell tandem solar cells (TSCs) with crystalline silicon (c-Si) as the bottom cell (TSC-Si). Previous works have pointed out that the optimal band gap, E g , of the top cell material for a TSC-Si is around 1.75 eV. With a tunable E g and better stability than MAPbI 3 (MA  =  CH 3 NH 3 ), MAPbI 3−x−y Br x Cl y is a promising candidate for the top cell material of a TSC-Si. In this work, calculations concerning the E g , refractive index and extinction coefficient of MAPbI 3−x−y Br x Cl y are performed using first-principles calculations including the spin–orbit coupling (SOC) effect. MAPbI 3−x−y Br x Cl y with five sets of x and y , which have a E g around 1.75 eV, are obtained. On this basis, absorption of the perovskite top cell is calculated applying the Lambert–Beer model (LBM) and the transfer matrix model (TMM), respectively. Considering the Auger recombination in the c-Si bottom cell and radiation coupling between the two subcells, the efficiencies for MAPbI 3−x−y Br x Cl y/ c-Si TSCs with the five sets of x and y are calculated. Among them, the MAPbI 2.375 Br 0.5 Cl 0.125 /c-Si TSC achieves the highest efficiency of 35.1% with a 440 nm thick top cell and 50 µ m thick c-Si when applying the LBM. When applying the TMM, the highest efficiency of 32.5% is predicted with a 580 nm thick MAPbI 2.375 Br 0.5 Cl 0.125 top cell and 50 µ m thick c-Si. Compared with the limiting efficiency of 27.1% for a 190 µ m thick c-Si single junction solar cell (SC), the MAPbI 2.375 Br 0.5 Cl 0.125 /c-Si TSC shows a superior performance of high efficiency and low c-Si consumption. (paper)

Electronic communication in phosphine substituted bridged dirhenium complexes - clarifying ambiguities raised by the redox non-innocence of the C4H2- and C4-bridges.

Science.gov (United States)

Li, Yan; Blacque, Olivier; Fox, Thomas; Luber, Sandra; Polit, Walther; Winter, Rainer F; Venkatesan, Koushik; Berke, Heinz

2016-04-07

The mononuclear rhenium carbyne complex trans-[Re(C[triple bond, length as m-dash]CSiMe3)([triple bond, length as m-dash]C-Me)(PMe3)4][PF6] (2) was prepared in 90% yield by heating a mixture of the dinitrogen complex trans-[ReCl(N2)(PMe3)4] (1), TlPF6, and an excess of HC[triple bond, length as m-dash]CSiMe3. 2 could be deprotonated with KOtBu to the vinylidene complex trans-[Re(C[triple bond, length as m-dash]CSiMe3)([double bond, length as m-dash]C[double bond, length as m-dash]CH2)(PMe3)4] (3) in 98% yield. Oxidation of 3 with 1.2 equiv. of [Cp2Fe][PF6] at -78 °C gave the Cβ-C'β coupled dinuclear rhenium biscarbyne complex trans-[(Me3SiC[triple bond, length as m-dash]C)(PMe3)4Re[triple bond, length as m-dash]C-CH2-CH2-C[triple bond, length as m-dash]Re(PMe3)4(C[triple bond, length as m-dash]CSiMe3)][PF6]2 (5) in 92% yield. Deprotonation of 5 with an excess of KOtBu in THF produced the diamagnetic trans-[(Me3SiC[triple bond, length as m-dash]C)(PMe3)4Re[double bond, length as m-dash]C[double bond, length as m-dash]CH-CH[double bond, length as m-dash]C[double bond, length as m-dash]Re(PMe3)4(C[triple bond, length as m-dash]CSiMe3)] complex (E-6(S)) in 87% yield with an E-butadienediylidene bridge. Density functional theory (DFT) calculations of E-6(S) confirmed its singlet ground state. The Z-form of 6 (Z-6(S)) could not be observed, which is in accord with its DFT calculated 17.8 kJ mol(-1) higher energy. Oxidation of E-6 with 2 equiv. of [Cp2Fe][PF6] resulted in the stable diamagnetic dicationic trans-[(Me3SiC[triple bond, length as m-dash]C)(PMe3)4Re[triple bond, length as m-dash]C-CH[double bond, length as m-dash]CH-C[triple bond, length as m-dash]Re(PMe3)4(C[triple bond, length as m-dash]CSiMe3)][PF6]2 complex (E-6[PF6]2) with an ethylenylidene dicarbyne structure of the bridge. The paramagnetic mixed-valence (MV) complex E-6[PF6] was obtained by comproportionation of E-6(S) and E-6[PF6]2 or by oxidation of E-6(S) with 1 equiv. of [Cp2Fe][PF6]. The

CSI Web Adventures: A Forensics Virtual Apprenticeship for Teaching Science and Inspiring STEM Careers

Science.gov (United States)

Miller, Leslie; Chang, Ching-I; Hoyt, Daniel

2010-01-01

CSI: The Experience, a traveling museum exhibit and a companion web adventure, was created through a grant from the National Science Foundation as a potential model for informal learning. The website was designed to enrich and complement the exhibit by modeling the forensic process. Substantive science, real-world lab techniques, and higher-level…

Adaptación del Inventario de Estrategias de Afrontamiento (CSI a la población penitenciaria de Mexico

Directory of Open Access Journals (Sweden)

Francisco Javier Rodríguez-Díaz

2014-01-01

Full Text Available El objetivo del estudio es adaptar el CSI - Inventario de Estrategias de Afrontamiento - al contexto penitenciario. La muestra - 261 penados, 97% varones (n=253 - del Sistema Postpenitenciario y Atención a Liberados (DSPAL del Estado Jalisco, México. Los instrumentos utilizados: Ficha Penitenciaria de Historia de Vida y el Inventario CSI. Los resultados refieren una estructura de primer orden casi idéntica a la obtenida para la población general, con niveles de consistencia interna satisfactorios, al mismo tiempo que la interpretación de segundo orden no confirma la estructura de segundo y tercer orden. Se discuten las implicaciones de los resultados para intervención penitenciaria.

Characterization of Material from Wells 299-W10-35 (C7573) and 299-W14-74 (C7024)

Energy Technology Data Exchange (ETDEWEB)

Tilton, Fred A.; Wellman, Dawn M.; Bovaird, Chase C.; Strandquist, Sara C.

2011-07-15

The objective of this work was to characterize material accumulating on wells 299-W10-35 (C7573) and 299-W14-74 (C7024) to determine the type of material (i.e., chemical or biological) and, if the material is biological, to identify the microorganisms present.

The Chemistry Scoring Index (CSI: A Hazard-Based Scoring and Ranking Tool for Chemicals and Products Used in the Oil and Gas Industry

Directory of Open Access Journals (Sweden)

Tim Verslycke

2014-06-01

Full Text Available A large portfolio of chemicals and products is needed to meet the wide range of performance requirements of the oil and gas industry. The oil and gas industry is under increased scrutiny from regulators, environmental groups, the public, and other stakeholders for use of their chemicals. In response, industry is increasingly incorporating “greener” products and practices but is struggling to define and quantify what exactly constitutes “green” in the absence of a universally accepted definition. We recently developed the Chemistry Scoring Index (CSI which is ultimately intended to be a globally implementable tool that comprehensively scores and ranks hazards to human health, safety, and the environment for products used in oil and gas operations. CSI scores are assigned to products designed for the same use (e.g., surfactants, catalysts on the basis of product composition as well as intrinsic hazard properties and data availability for each product component. As such, products with a lower CSI score within a product use group are considered to have a lower intrinsic hazard compared to other products within the same use group. The CSI provides a powerful tool to evaluate relative product hazards; to review and assess product portfolios; and to aid in the formulation of products.

Physical Research Laboratory radiocarbon 14C dates : CS-I

International Nuclear Information System (INIS)

Agrawal, D.P.; Krishnamurthy, R.V.; Kusumgar, Sheela; Pant, R.K.

1978-01-01

The 14 C dates of archaeological samples measured at the Radiocarbon Laboratory of the Physical Research Laboratory, Ahmedabad are presented. Samples were converted into methane and measured in gas proportional counters. Ninety-five percent activity of NBS oxalic acid was used as modern standard. The dates in years B.P. are given for each sample based on the half-life values of 5568 +- 30 years and 5730 +- 40 years, the latter within parenthesis. The dates are not calibrated for 14 C/ 12 C variations. To convert the dates into AD/BC scale, 1950 AD should be used as reference year. A number of 14 C dates (PRL-81, -83, -67, -68) now confirm that the Painted Grey Ware culture extended upto the 3rd century BC. Some of the dates from Barkhera (PRL-113), Bateshwar (PRL-200), Bhimbetka (PRL-17) and Koldihawa (PRL-100, 101) are older than normally expected, probably indicative of some hitherto unknown basal cultures in these regions. 14 C dates on in situ Megalithic materials do not seem to go beyond 200 BC. (author)

Radiolysis of cesium iodide solutions at 35 and 85 deg C

International Nuclear Information System (INIS)

Lucas, M.

1981-09-01

An aqueous solution of cesium iodide was irradiated by the gamma rays from a cobalt 60 source with a dose rate of 0.4 Mrad/hr. At 35 deg C the iodide I - is oxidized in molecular iodine I 2 but at 85 deg C the iodate IO 3 - is obtained. The aim of this work is the study of aerosols behaviour released in accidental situation of a PWR in presence of steam [fr

3',5'-cIMP as Potential Second Messenger in the Vascular Wall.

Science.gov (United States)

Leung, Susan W S; Gao, Yuansheng; Vanhoutte, Paul M

2017-01-01

Traditionally, only the 3',5'-cyclic monophosphates of adenosine and guanosine (produced by adenylyl cyclase and guanylyl cyclase, respectively) are regarded as true "second messengers" in the vascular wall, despite the presence of other cyclic nucleotides in different tissues. Among these noncanonical cyclic nucleotides, inosine 3',5'-cyclic monophosphate (cIMP) is synthesized by soluble guanylyl cyclase in porcine coronary arteries in response to hypoxia, when the enzyme is activated by endothelium-derived nitric oxide. Its production is associated with augmentation of vascular contraction mediated by stimulation of Rho kinase. Based on these findings, cIMP appears to meet most, if not all, of the criteria required for it to be accepted as a "second messenger," at least in the vascular wall.

Creep, Fatigue and Fracture Behavior of Environmental Barrier Coating and SiC-SiC Ceramic Matrix Composite Systems: The Role of Environment Effects

Science.gov (United States)

Zhu, Dongming; Ghosn, Louis J.

2015-01-01

Advanced environmental barrier coating (EBC) systems for low emission SiCSiC CMC combustors and turbine airfoils have been developed to meet next generation engine emission and performance goals. This presentation will highlight the developments of NASAs current EBC system technologies for SiC-SiC ceramic matrix composite combustors and turbine airfoils, their performance evaluation and modeling progress towards improving the engine SiCSiC component temperature capability and long-term durability. Our emphasis has also been placed on the fundamental aspects of the EBC-CMC creep and fatigue behaviors, and their interactions with turbine engine oxidizing and moisture environments. The EBC-CMC environmental degradation and failure modes, under various simulated engine testing environments, in particular involving high heat flux, high pressure, high velocity combustion conditions, will be discussed aiming at quantifying the protective coating functions, performance and durability, and in conjunction with damage mechanics and fracture mechanics approaches.

Micro-computed tomographic comparison of nickel-titanium rotary versus traditional instruments in C-shaped root canal system.

Science.gov (United States)

Yin, Xingzhe; Cheung, Gary Shun-Pan; Zhang, Chengfei; Masuda, Yoshiko Murakami; Kimura, Yuichi; Matsumoto, Koukichi

2010-04-01

The purpose of this study was to assess the efficacy of instrumentation of C-shaped canals with ProTaper rotary system and traditional instruments by using micro-computed tomography (micro-CT). Twenty-four mandibular molars with C-shaped canals were selected in pairs and sorted equally into 2 groups, which were assigned for instrumentation by ProTaper rotary system (ProTaper group) or by K-files and Gates-Glidden burs (Hand Instrument group). Three-dimensional images were constructed by micro-CT. The volume of dentin removed, uninstrumented canal area, time taken for instrumentation, and iatrogenic error of instrumentation were investigated. Hand Instrument group showed greater amount of volumetric dentin removal and left less uninstrumented canal area than ProTaper group (P ProTaper group than for Hand Instrument group (P Hand Instrument group than for ProTaper group. It was concluded that ProTaper rotary system maintained the canal curvature with speediness and few procedural errors, whereas traditional instrumentation can clean more canal surface. Copyright (c) 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

System on chip (SoC) microcontrollers (μC) as digitisers for ion beam analysis (IBA) instruments

Energy Technology Data Exchange (ETDEWEB)

Whitlow, Harry J., E-mail: harry.j@whitlow.se

2016-09-15

Data digitisation of the analogue signals from detectors to digital data is an essential process in ion beam analysis (IBA). The low-cost, easy availability and development environments that have a low learning threshold makes system-on-chip (SoC) microcontrollers (μC) attractive for this task. These μC combine, on one die, analogue and digital inputs and outputs with serial USB interfaces, which opens up simple implementation of tailor-made interfaces for specific IBA measurement systems. We have investigated the design and performance limitations based on development of three different digitisation interfaces for IBA. These were a two-channel nuclear instrumentation module (NIM) ADC event mode interface (EMI) for a high-resolution magnetic RBS spectrometer, a simple headless-multi-channel analyser (MCA) and a combined dual channel headless MCA and EMI. It is shown that SoC μC based interfaces for digitisation of analogue spectroscopy pulses in IBA systems can be implemented for material costs less than 100 €. The performance of the SoC devices for many IBA applications is close to what can be achieved with state-of-the-art instruments. The simple pulse spectroscopy interface circuit and software are included in the auxiliary archive.

Development and Performance Evaluations of HfO2-Si and Rare Earth-Si Based Environmental Barrier Bond Coat Systems for SiC/SiC Ceramic Matrix Composites

Science.gov (United States)

Zhu, Dongming

2014-01-01

Ceramic environmental barrier coatings (EBC) and SiCSiC ceramic matrix composites (CMCs) will play a crucial role in future aircraft propulsion systems because of their ability to significantly increase engine operating temperatures, improve component durability, reduce engine weight and cooling requirements. Advanced EBC systems for SiCSiC CMC turbine and combustor hot section components are currently being developed to meet future turbine engine emission and performance goals. One of the significant material development challenges for the high temperature CMC components is to develop prime-reliant, high strength and high temperature capable environmental barrier coating bond coat systems, since the current silicon bond coat cannot meet the advanced EBC-CMC temperature and stability requirements. In this paper, advanced NASA HfO2-Si based EBC bond coat systems for SiCSiC CMC combustor and turbine airfoil applications are investigated. The coating design approach and stability requirements are specifically emphasized, with the development and implementation focusing on Plasma Sprayed (PS) and Electron Beam-Physic Vapor Deposited (EB-PVD) coating systems and the composition optimizations. High temperature properties of the HfO2-Si based bond coat systems, including the strength, fracture toughness, creep resistance, and oxidation resistance were evaluated in the temperature range of 1200 to 1500 C. Thermal gradient heat flux low cycle fatigue and furnace cyclic oxidation durability tests were also performed at temperatures up to 1500 C. The coating strength improvements, degradation and failure modes of the environmental barrier coating bond coat systems on SiCSiC CMCs tested in simulated stress-environment interactions are briefly discussed and supported by modeling. The performance enhancements of the HfO2-Si bond coat systems with rare earth element dopants and rare earth-silicon based bond coats are also highlighted. The advanced bond coat systems, when

5 CFR 1620.35 - Loan payments.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Loan payments. 1620.35 Section 1620.35... Nonappropriated Fund Employees § 1620.35 Loan payments. NAF instrumentalities must deduct and transmit TSP loan... CFR part 1655 and Board procedures. Loan payments may not be deducted and transmitted for employees...

Downlink Linear Precoders Based on Statistical CSI for Multicell MIMO-OFDM

Directory of Open Access Journals (Sweden)

Ebrahim Baktash

2017-01-01

Full Text Available With 5G communication systems on the horizon, efficient interference management in heterogeneous multicell networks is more vital than ever. This paper investigates the linear precoder design for downlink multicell multiple-input multiple-output orthogonal frequency-division multiplexing (MIMO-OFDM systems, where base stations (BSs coordinate to reduce the interference across space and frequency. In order to minimize the overall feedback overhead in next-generation systems, we consider precoding schemes that require statistical channel state information (CSI only. We apply the random matrix theory to approximate the ergodic weighted sum rate of the system with a closed form expression. After formulating the approximation for general channels, we reduce the results to a more compact form using the Kronecker channel model for which several multicarrier concepts such as frequency selectivity, channel tap correlations, and intercarrier interference (ICI are rigorously represented. We find the local optimal solution for the maximization of the approximate rate using a gradient method that requires only the covariance structure of the MIMO-OFDM channels. Within this covariance structure are the channel tap correlations and ICI information, both of which are taken into consideration in the precoder design. Simulation results show that the rate approximation is very accurate even for very small MIMO-OFDM systems and the proposed method converges rapidly to a near-optimal solution that competes with networked MIMO and precoders based on instantaneous full CSI.

The radial and azimuthal properties of volatiles and dust in the inner coma of Comet 45P/Honda-Mrkos-Pajdušáková

Science.gov (United States)

Harris, Walter M.; Ryan, Erin L.; Springmann, Alessondra; Mueller, Beatrice E. A.; Samarasinha, Nalin H.; Kikwaya Elou, Jean-Baptiste; Howell, Ellen S.; Lejoly, Cassandra; Bodnarik, Julia; Fitzpatrick, Ryleigh; Maciel, Ricardo; Mitchell, Adriana; Watson, Zachary Tyler

2017-10-01

In February 2017 comet 45P/Honda-Mrkos-Pajdušáková (HMP) passed by the Earth at a perigee distance of 0.08 AU. Such encounters provide an important opportunity for study of the inner coma region where gas and dust production occur. We report here on wide-field (30 x 30 arcminute), high-spatial resolution (35 km/pixel) observations of HMP obtained with the 90Prime One imager on the 2.3m Bok telescope at Kitt Peak. The observations were performed on February 16 and 17, when the comet was 0.1 AU from Earth, using a combination of a wide-band Gunn r’ filter and a subset of the HB filter library (OH, CN, C2, Blue Continuum). In this presentation we will discuss the distribution and color of the dust, the relative production rates of volatiles, and the implied parent-daughter photochemical evolution from radial expansion modeling.

A fast position sensitive photodetector based on a CsI reflective photocathode

International Nuclear Information System (INIS)

Arnold, R.; Christophel, E.; Guyonnet, J.L.

1991-01-01

A fast detector was built for UV photon detection that depends on a CsI sensitized pad cathode. The rapidity of the detector is compared with that of a more classical chamber filled with photosensitive gases such as TEA or TMAE. Estimates of the quantum yield of the photocathode at 160 and 200 nm are given. The performances obtained make it a good photodetector candidate to be operated at high luminosity accelerators. (author) 7 refs., 19 figs

pPKCδ activates SC35 splicing factor during H9c2 myoblastic differentiation.

Science.gov (United States)

Zara, Susi; Falconi, Mirella; Rapino, Monica; Zago, Michela; Orsini, Giovanna; Mazzotti, Giovanni; Cataldi, Amelia; Teti, Gabriella

2011-01-01

Although Protein Kinase C (PKC) isoforms' role in the neonatal and adult cardiac tissue development and ageing has been widely described "in vivo", the interaction of such enzymes with specific nuclear substrates needs to be investigated. The aim of our research has been the study of the expression, localization and interaction with the splicing factor SC35 of PKC isoforms (α, δ, ε, ζ) and their potential role in modulating the transcription machinery. H9c2 cells induced to myoblast differentiation in the presence of 1% Horse Serum (HS) have represented our experimental model. The expression of PKC isoforms, their distribution and interaction with SC35 have been evaluated by western blotting, co-immunoprecipitation and double gold immunolabeling for transmission and scanning electron microscopy. Our results show PKCδ as the most expressed isoform in differentiated cells. Surprisingly, the distribution of PKCδ and SC35 does not show any significant modification between 10%FBS and 1%HS treated samples and no co-localization is observed. Moreover the interaction between the phosphorylated form of PKCδ (pPKCδ) and SC35 increases, is distributed and co-localizes within the nucleus of differentiated H9c2. These data represent reasonable evidence of pPKCδ mediated SC35 splicing factor activation, suggesting its direct effect on transcription via interaction with the transcription machinery. Furthermore, this co-localization represents a crucial event resulting in downstream changes in transcription of components which determine the morphological modifications related to cardiomyoblast differentiated phenotype.

The first 3':5'-cyclic nucleotide-amino acid complex: L-His-cIMP.

Science.gov (United States)

Slepokura, Katarzyna

2012-08-01

In the crystal structure of the L-His-cIMP complex, i.e. L-histidinium inosine 3':5'-cyclic phosphate [systematic name: 5-(2-amino-2-carboxyethyl)-1H-imidazol-3-ium 7-hydroxy-2-oxo-6-(6-oxo-6,9-dihydro-1H-purin-9-yl)-4a,6,7,7a-tetrahydro-4H-1,3,5,2λ(5)-furo[3,2-d][1,3,2λ(5)]dioxaphosphinin-2-olate], C(6)H(10)N(3)O(2)(+)·C(10)H(10)N(4)O(7)P(-), the Hoogsteen edge of the hypoxanthine (Hyp) base of cIMP and the Hyp face are engaged in specific amino acid-nucleotide (His···cIMP) recognition, i.e. by abutting edge-to-edge and by π-π stacking, respectively. The Watson-Crick edge of Hyp and the cIMP phosphate group play a role in nonspecific His···cIMP contacts. The interactions between the cIMP anions (anti/C3'-endo/trans-gauche/chair conformers) are realized mainly between riboses and phosphate groups. The results for this L-His-cIMP complex, compared with those for the previously reported solvated L-His-IMP crystal structure, indicate a different nature of amino acid-nucleotide recognition and interactions upon the 3':5'-cyclization of the nucleotide phosphate group.

Performance and microbial community composition dynamics of aerobic granular sludge from sequencing batch bubble column reactors operated at 20 degrees C, 30 degrees C, and 35 degrees C.

Science.gov (United States)

Ebrahimi, Sirous; Gabus, Sébastien; Rohrbach-Brandt, Emmanuelle; Hosseini, Maryam; Rossi, Pierre; Maillard, Julien; Holliger, Christof

2010-07-01

Two bubble column sequencing batch reactors fed with an artificial wastewater were operated at 20 degrees C, 30 degrees C, and 35 degrees C. In a first stage, stable granules were obtained at 20 degrees C, whereas fluffy structures were observed at 30 degrees C. Molecular analysis revealed high abundance of the operational taxonomic unit 208 (OTU 208) affiliating with filamentous bacteria Leptothrix spp. at 30 degrees C, an OTU much less abundant at 20 degrees C. The granular sludge obtained at 20 degrees C was used for the second stage during which one reactor was maintained at 20 degrees C and the second operated at 30 degrees C and 35 degrees C after prior gradual increase of temperature. Aerobic granular sludge with similar physical properties developed in both reactors but it had different nutrient elimination performances and microbial communities. At 20 degrees C, acetate was consumed during anaerobic feeding, and biological phosphorous removal was observed when Rhodocyclaceae-affiliating OTU 214 was present. At 30 degrees C and 35 degrees C, acetate was mainly consumed during aeration and phosphorous removal was insignificant. OTU 214 was almost absent but the Gammaproteobacteria-affiliating OTU 239 was more abundant than at 20 degrees C. Aerobic granular sludge at all temperatures contained abundantly the OTUs 224 and 289 affiliating with Sphingomonadaceae indicating that this bacterial family played an important role in maintaining stable granular structures.

Instrument evaluation no. 11. ESI nuclear model 271 C contamination monitor

International Nuclear Information System (INIS)

Burgess, P.H.; Iles, W.J.

1978-06-01

The various radiations encountered in radiological protection cover a wide range of energies and radiation measurements have to he carried out under an equally broad spectrum of environmental conditions. This report is one of a series intended to give information on the performance characteristics of radiological protection instruments, to assist in the selection of appropriate instruments for a given purpose, to interpret the results obtained with such instruments, and, in particular, to know the likely sources and magnitude of errors that might be associated with measurements in the field. The radiation, electrical and environmental characteristics of radiation protection instruments are considered together with those aspects of the construction which make an instrument convenient for routine use. To provide consistent criteria for instrument performance, the range of tests performed on any particular class of instrument, the test methods and the criteria of acceptable performance are based broadly on the appropriate Recommendations of the International Electrotechnical Commission. The radiations in the tests are, in general, selected from the range of reference radiations for instrument calibration being drawn up by the International Standards Organisation. Normally, each report deals with the capabilities and limitations of one model of instrument and no direct comparison with other instruments intended for similar purposes is made, since the significance of particular performance characteristics largely depends on the radiations and environmental conditions in which the instrument is to be used. The results quoted here have all been obtained from tests on instruments in routine production, with the appropriate measurements being made by the NRPB. This report deals with the ESI Nuclear Model 271 C; a general purpose contamination monitor, comprising a GM tube connected by a coiled extensible cable to a ratemeter

A self-calibrating ion beam profiler based on a CsI scintillator

Energy Technology Data Exchange (ETDEWEB)

Finocchiaro, P. E-mail: finocchiaro@lns.infn.it; Ciavola, G.; Cosentino, L.; Gu, M.; Raia, G.; Rovelli, A

1999-11-21

We report on the test results obtained with a prototype beam profiler based on a thin slit and a CsI scintillator, read out by means of a compact photomultiplier. Such a device has proven to be suitable to perform ion beam diagnostics at low and very low intensities. In particular, our device is suitable for being used in the energy and intensity ranges expected at the EXCYT radioactive ion beam facility, that is currently under development at LNS Catania.

A self-calibrating ion beam profiler based on a CsI scintillator

International Nuclear Information System (INIS)

Finocchiaro, P.; Ciavola, G.; Cosentino, L.; Gu, M.; Raia, G.; Rovelli, A.

1999-01-01

We report on the test results obtained with a prototype beam profiler based on a thin slit and a CsI scintillator, read out by means of a compact photomultiplier. Such a device has proven to be suitable to perform ion beam diagnostics at low and very low intensities. In particular, our device is suitable for being used in the energy and intensity ranges expected at the EXCYT radioactive ion beam facility, that is currently under development at LNS Catania

Quantum efficiency measurement system for large area CsI photodetectors

CERN Document Server

Cusanno, F; Colilli, S; Crateri, R; Fratoni, R; Frullani, S; Garibaldi, F; Giuliani, F; Gricia, M; Lucentini, M; Mostarda, A; Santavenere, F; Veneroni, P; Breuer, H; Iodice, M; Urciuoli, G M; De Cataldo, G; De Leo, R; Lagamba, L; Braem, André

2003-01-01

A proximity focusing freon/CsI RICH detector has been built for kaon physics at Thomas Jefferson National Accelerator Facility (TJNAF or Jefferson Lab), Hall A. The Cherenkov photons are detected by a UV photosensitive CsI film which has been obtained by vacuum evaporation. A dedicated evaporation facility for large area photocathodes has been built for this task. A measuring system has been built to allow the evaluation of the absolute quantum efficiency (QE) just after the evaporation. The evaporation facility is described here, as well as the quantum efficiency measurement device. Results of the QE on-line measurements, for the first time on large area photocathodes, are reported.

Optical properties of CsI single crystals irradiated with neutrons at low temperature

International Nuclear Information System (INIS)

Okada, M.; Atobe, K.; Itatani, N.; Ozawa, K.

1998-01-01

Optical properties of the irradiation-induced-defects in neutron-irradiated CsI single crystals have been investigated. The nominally pure CsI crystals are irradiated by reactor fast neutrons (E>0.1 MeV) with a fluence of 1.4 x 10 15 n/cm 2 at 20 K and by γ-rays from 60 Co source to a dose of 1.5 x 10 4 Gy at liquid nitrogen temperature (LNT). After the irradiations, isochronal annealings are performed to investigate the thermal behavior of the defects. The glow peaks of the thermoluminescence (TL) in each sample irradiated with neutrons at 20 K and with γ-rays at LNT are observed at about 100, 160 and 220 K. In the neutron-irradiated samples at 20 K, the emission band at 338 nm is observed at LNT. It is supposed that this emission band occurs by an excitation of γ-rays from 134 Cs, which is radioactivated by thermal neutrons among the reactor radiations. It is confirmed that the temperature dependence of the 338 nm band is similar with that of the emission band due to the self-trapped exciton which is introduced into the non-irradiated samples illuminated by higher energy photons. (orig.)

Optical properties of CsI single crystals irradiated with neutrons at low temperature

Energy Technology Data Exchange (ETDEWEB)

Okada, M. [Kyoto Univ., Kumatori, Osaka (Japan). Research Reactor Inst.; Nakagawa, M. [Faculty of Education, Kagawa Univ., Takamatsu, Kagawa (Japan); Atobe, K. [Faculty of Science, Naruto Univ. of Education, Naruto, Tokushima (Japan); Itatani, N.; Ozawa, K. [Horiba Ltd., Minamiku, Kyoto (Japan)

1998-05-01

Optical properties of the irradiation-induced-defects in neutron-irradiated CsI single crystals have been investigated. The nominally pure CsI crystals are irradiated by reactor fast neutrons (E>0.1 MeV) with a fluence of 1.4 x 10{sup 15} n/cm{sup 2} at 20 K and by {gamma}-rays from {sup 60}Co source to a dose of 1.5 x 10{sup 4} Gy at liquid nitrogen temperature (LNT). After the irradiations, isochronal annealings are performed to investigate the thermal behavior of the defects. The glow peaks of the thermoluminescence (TL) in each sample irradiated with neutrons at 20 K and with {gamma}-rays at LNT are observed at about 100, 160 and 220 K. In the neutron-irradiated samples at 20 K, the emission band at 338 nm is observed at LNT. It is supposed that this emission band occurs by an excitation of {gamma}-rays from {sup 134}Cs, which is radioactivated by thermal neutrons among the reactor radiations. It is confirmed that the temperature dependence of the 338 nm band is similar with that of the emission band due to the self-trapped exciton which is introduced into the non-irradiated samples illuminated by higher energy photons. (orig.) 13 refs.

Synthesis of organic substances labelled with {sup 14}C and {sup 35}S; Syntheses de molecules organiques marquees par le carbone-14 et le soufre-35

Energy Technology Data Exchange (ETDEWEB)

Pichat, L [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

After a brief history of the development of the Section des Molecules marquees of the Frenchmic Energy Commission, the author gives an outline of the synthesis of the following labelled compounds: benzene {sup 14}C-6; phenyl-p-fluorophenyl, thienyl-2 {beta} alanines {beta} {sup 14}C; noradrenaline {beta} {sup 14}C (arterenol {beta} {sup 14}C), dotriacontane {sup 14}C-16-17, aminoethane sulfinic acid (hypotaurine {sup 35}S). (author)Fren. [French] Apres un bref historique du developpement de la Section des Molecules marquees du Commissariat a l'Energie Atomique fran is, l'auteur donne un resume des syntheses des composes marques suivants: benzene {sup 14}C-6; phenyl-p-fluorophenyl, thienyl-2 {beta} alamines {beta} {sup 14}C; noradrenaline {beta} {sup 14}C (arterenol {beta} {sup 14}C), dotriacontane {sup 14}C-16-17, acide aminoethane sulfinique (hypotaurine {sup 35}S). (auteur)

Efeito do bicarbonato de sódio no tratamento de vinhaça em AnSBBR operado a 55 e 35ºC Effect of the sodium bicarbonate in the treatment of vinasse in AnSBBR operated at 55 and 35ºC

Directory of Open Access Journals (Sweden)

Maria Magdalena Ribas Döll

2010-09-01

Full Text Available Avaliou-se a influência do bicarbonato de sódio (NaHCO3 no desempenho do reator anaeróbio batelada sequencial com biomassa imobilizada tratando vinhaça a 55 e a 35ºC. O reator foi preenchido com espuma de poliuretano e agitado a 300 rpm. A adaptação a 55ºC estendeu-se por 50 dias, tendo o reator sido alimentado com vinhaça (DQO de 0,3 a 1,0 g/L. Para a operação a 35ºC, procedeu-se inicialmente ao enriquecimento da população metanogênica, durante 21 dias, com substrato à base de etanol (2,5 gDQO/L. Posteriormente, cargas orgânicas volumétricas (COV de 0,85 a 5,70 gDQO/L.d foram aplicadas no reator a 55ºC, com suplementação de 1,2 a 0,4 gHCO3-/gDQO. A 35ºC, o reator foi submetido a COV de 2,85 a 36,0 gDQO/L.d com 0,4 a 0,2 gHCO3-/gDQO. A remoção de DQO variou de 43 a 78% a 55ºC e de 75 a 85% a 35ºC. A suplementação de alcalinidade mostrou-se essencial para a estabilidade do processo, sendo requerida em menor quantidade a 35ºC.The influence of the sodium bicarbonate (NaHCO3 on the performance of an anaerobic sequencing batch biofilm reactor treating vinasse at 55 and 35ºC was evaluated. The reactor was filled with polyurethane foam and agitated at 300 rpm. The acclimatization period at 55ºC lasted 50 days, and the reactor was fed with vinasse (COD from 0.3 to 1.0 g/L. A previous enrichment of methanogenic population was provided for the reactor operated at 35ºC, feeding it with an ethanol based substrate (2.5 gCOD/L during 21 days. Further on, organic loading rates (OLR ranging from 0.85 to 5.70 gCOD/L.d were applied to the reactor at 55ºC, supplemented with 1.2 to 0.4 gHCO3-/gCOD. At 35ºC the reactor was subjected to OLR ranging from 2.85 to 36.0 gCOD/L.d with 0.4 to 0.2 gHCO3-/gCOD. COD removal ranged from 43 to 78% at 55ºC and from 75 to 85% at 35ºC. Alkalinity supplementation was found to be essential for process stability, but the amount required was lower at 35ºC.

Two-way CSI-assisted AF relaying with HPA nonlinearity

KAUST Repository

Qi, Jian

2015-09-11

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal-to-noise ratio (SNR) is derived as per the modified system model by taking into account the interference caused by relaying scheme and HPA nonlinearity. The system performance of the considered relaying network is evaluated in terms of average symbol error probability (SEP) in Nakagami-m fading channels, by making use of the moment-generating function (MGF) approach. Numerical results are provided and show the effects of several parameters, such as quadrature amplitude modulation (QAM) order, number of relays, HPA parameters, and Nakagami parameter, on performance. © 2015 IEEE.

Radiation hardness test of un-doped CsI crystals and Silicon Photomultipliers for the Mu2e calorimeter

Science.gov (United States)

Baccaro, S.; Cemmi, A.; Cordelli, M.; Diociaiuti, E.; Donghia, R.; Giovannella, S.; Loreti, S.; Miscetti, S.; Pillon, M.; Sarra, I.

2017-11-01

The Mu2e calorimeter is composed by 1400 un-doped CsI crystals coupled to large area UV extended Silicon Photomultipliers arranged in two annular disks. This calorimeter has to provide precise information on energy, timing and position. It should also be fast enough to handle the high rate background and it must operate and survive in a high radiation environment. Simulation studies estimated that, in the hottest regions, each crystal will absorb a dose of 300 Gy and will be exposed to a neutron fluency of 6 × 1011 n/cm2 in 3 years of running. Test of un-doped CsI crystals irradiated up to 900 Gy and to a neutron fluency up to 9 × 1011 n/cm2 have been performed at CALLIOPE and FNG ENEA facilities in Italy. We present our study on the variation of light yield (LY) and longitudinal response uniformity (LRU) of these crystals after irradiation. The ionization dose does not modify LRU while a 20% reduction in LY is observed at 900 Gy. Similarly, the neutron flux causes an acceptable LY deterioration (≤ 15%). A neutron irradiation test on different types of SIPMs (two different array models from Hamamatsu and one from FBK) have also been carried out by measuring the variation of the leakage current and the charge response to an ultraviolet led. We concluded that, in the experiment, we will need to cool down the SIPMs to 0 °C reduce the leakage current to an acceptable level.

Craniospinal versus whole brain irradiation in Medulloblastoma patients, with introduction of utilizing a simple immobilization device

Directory of Open Access Journals (Sweden)

Haddad P

2001-05-01

Full Text Available Craniospinal irradiation plus posterior fossa boost (CS1 is the standard modality of post-operative treatment of patient with medulloblastoma, but considering the technical difficulties and limited facilities, often whole- brain irradiation plus posterior fossa boost (WBI had been used in our institution until 1991. Tust a retrospective study was undertaken to compare the patients treated by By WBI and CSI for recurrences and disease-free survival (DFS. Files of all medullobalstoma patients treated post-operatively in our department in the 10 – year period of 1986-1996 were reviewed. To obtain the best possible follow- up, a formal inquiry letter was mailed to all patients’ addresses.Total of 72 patients had been treated, with a mean age of 14.7 years and male-to-female ratio of 1.5:1 Thirty –seven patients had been treated by WBI and 35 by CS. A simple wooden device designed and made in our department was used for CSI patients’ set-up and immobilization. Mean radiation dose to posterior fossa was 4, 765 cGy in WBT and 5, 071 cGY in CSI (180-200 cGy fractions. Sixty-two patients (85% came back for follow-up, with 24 recurrences. Only 24% of CSI patients had recurrences, versus 51% in WBI Nearly all Wbi recurrences versus half of the CSI recurrences were spinal. DFS was 39 months in CSI and 26 months in WBI (P<0.001 . in multi-factorial analysis, only the extent of radiation (CSI versus WBI, P<0.001 was statistically significant. Mean age in our patients was higher than what is commonly reported in literature. The immobilization device introduce was a simple and useful accessory to CSI. Considering DFS, CSI in our department was acceptabley comparable to literature results and significantly superior to WBI. With regard to relatively high spinal recurrence rate even in CSI, the importance of suitable spinal cytological and imaging evaluation is again emphasized.

Grinding, Machining Morphological Studies on C/SiC Composites

Science.gov (United States)

Xiao, Chun-fang; Han, Bing

2018-05-01

C/SiC composite is a typical material difficult to machine. It is hard and brittle. In machining, the cutting force is large, the material removal rate is low, the edge is prone to collapse, and the tool wear is serious. In this paper, the grinding of C/Si composites material along the direction of fiber distribution is studied respectively. The surface microstructure and mechanical properties of C/SiC composites processed by ultrasonic machining were evaluated. The change of surface quality with the change of processing parameters has also been studied. By comparing the performances of conventional grinding and ultrasonic grinding, the surface roughness and functional characteristics of the material can be improved by optimizing the processing parameters.

An application of CCD read-out technique to neutron distribution measurement using the self-activation method with a CsI scintillator plate

International Nuclear Information System (INIS)

Nohtomi, Akihiro; Kurihara, Ryosuke; Kinoshita, Hiroyuki; Honda, Soichiro; Tokunaga, Masaaki; Uno, Heita; Shinsho, Kiyomitsu; Wakabayashi, Genichiro; Koba, Yusuke; Fukunaga, Junichi; Umezu, Yoshiyuki; Nakamura, Yasuhiko; Ohga, Saiji

2016-01-01

In our previous paper, the self-activation of an NaI scintillator had been successfully utilized for detecting photo-neutrons around a high-energy X-ray radiotherapy machine; individual optical pulses from the self-activated scintillator are read-out by photo sensors such as a photomultiplier tube (PMT). In the present work, preliminary observations have been performed in order to apply a direct CCD read-out technique to the self-activation method with a CsI scintillator plate using a Pu-Be source and a 10-MV linac. In conclusion, it has been revealed that the CCD read-out technique is applicable to neutron measurement around a high-energy X-ray radiotherapy machine with the self-activation of a CsI plate. Such application may provide a possibility of novel method for simple neutron dose-distribution measurement. - Highlights: • Preliminary observations have been performed by a CCD for the CsI self-activation method. • It has been revealed that the CCD read-out technique is applicable to neutron measurement. • Such application may provide a novel method for simple neutron distribution measurement.

An application of CCD read-out technique to neutron distribution measurement using the self-activation method with a CsI scintillator plate

Energy Technology Data Exchange (ETDEWEB)

Nohtomi, Akihiro, E-mail: nohtomi@hs.med.kyushu-u.ac.jp [Graduate School of Medical Sciences, Kyushu University, 3-1-1 Maidashi, Higashi-ku, Fukuoka 812-8582 (Japan); Kurihara, Ryosuke; Kinoshita, Hiroyuki; Honda, Soichiro; Tokunaga, Masaaki; Uno, Heita [Graduate School of Medical Sciences, Kyushu University, 3-1-1 Maidashi, Higashi-ku, Fukuoka 812-8582 (Japan); Shinsho, Kiyomitsu [Graduate School of Human Sciences, Tokyo Metropolitan University, 7-2-10 Higashi-oku, Arakawa-ku, Tokyo 116-8551 (Japan); Wakabayashi, Genichiro [Atomic Energy Research Institute, Kinki University, 3-4-1 Kowakae, Higashiosaka-shi, Osaka 577-8502 (Japan); Koba, Yusuke [National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba-shi, Chiba 263-8555 (Japan); Fukunaga, Junichi; Umezu, Yoshiyuki; Nakamura, Yasuhiko [Department of Radiology, Kyushu University Hospital, 3-1-1 Maidashi, Higashi-ku, Fukuoka 812-8582 (Japan); Ohga, Saiji [Department of Clinical Radiology, Graduate School of Medical Sciences, Kyushu University, 3-1-1 Maidashi, Higashi-ku, Fukuoka 812-8582 (Japan)

2016-10-01

In our previous paper, the self-activation of an NaI scintillator had been successfully utilized for detecting photo-neutrons around a high-energy X-ray radiotherapy machine; individual optical pulses from the self-activated scintillator are read-out by photo sensors such as a photomultiplier tube (PMT). In the present work, preliminary observations have been performed in order to apply a direct CCD read-out technique to the self-activation method with a CsI scintillator plate using a Pu-Be source and a 10-MV linac. In conclusion, it has been revealed that the CCD read-out technique is applicable to neutron measurement around a high-energy X-ray radiotherapy machine with the self-activation of a CsI plate. Such application may provide a possibility of novel method for simple neutron dose-distribution measurement. - Highlights: • Preliminary observations have been performed by a CCD for the CsI self-activation method. • It has been revealed that the CCD read-out technique is applicable to neutron measurement. • Such application may provide a novel method for simple neutron distribution measurement.

Nuclear instrumentation system for the integrated digital I and C system

International Nuclear Information System (INIS)

Isobe, Yuji; Nakamura, Shingo

2005-01-01

Development of a new nuclear instrumentation (NI) system has been done. The new system is suitable for the digital instrumentation and control (I and C) systems. Higher reliability and lower development costs have been achieved by applying good performance circuits with sufficient experience of the conventional NI system. Human-system interface (HSI) and maintainability have been improved comparing with the conventional NI system because of the partial digitalisation. The new NI system has been manufactured and validated. We are finally verifying the total performance now

Nuclear instrumentation system for the integrated digital I and C system

Energy Technology Data Exchange (ETDEWEB)

Isobe, Yuji [Mitsubishi Heavy Industries, Tokyo (Japan); Nakamura, Shingo [Mitsubishi, Electric Corporation, Tokyo (Japan)

2005-11-15

Development of a new nuclear instrumentation (NI) system has been done. The new system is suitable for the digital instrumentation and control (I and C) systems. Higher reliability and lower development costs have been achieved by applying good performance circuits with sufficient experience of the conventional NI system. Human-system interface (HSI) and maintainability have been improved comparing with the conventional NI system because of the partial digitalisation. The new NI system has been manufactured and validated. We are finally verifying the total performance now.

Development of a low-cost-high-sensitivity Compton camera using CsI (Tl) scintillators (γI)

Energy Technology Data Exchange (ETDEWEB)

Kagaya, M., E-mail: 13nd401n@vc.ibaraki.ac.jp [College of Science, Ibaraki University, 2-1-1 Bunkyo, Mito City, Ibaraki 310-8512 (Japan); Open-It consortium (Japan); Katagiri, H. [College of Science, Ibaraki University, 2-1-1 Bunkyo, Mito City, Ibaraki 310-8512 (Japan); Open-It consortium (Japan); Enomoto, R. [Institute for Cosmic Ray Research, University of Tokyo, 5-1-5 Kashiwa-no-Ha, Kashiwa City, Chiba 277-8582 (Japan); Open-It consortium (Japan); Hanafusa, R.; Hosokawa, M.; Itoh, Y. [Fuji Electric, 1 Fujimachi, Hino City, Tokyo 191-8502 (Japan); Muraishi, H. [School of Allied Health Science, Kitasato University, 1-15-1 Kitasato, Minami-ku, Sagamihara City, Kanagawa 252-0373 (Japan); Open-It consortium (Japan); Nakayama, K. [College of Science, Ibaraki University, 2-1-1 Bunkyo, Mito City, Ibaraki 310-8512 (Japan); Open-It consortium (Japan); Satoh, K. [Shinsei Corporation, 4-9-1 Nihonbashi-honcho, Chuo-ku, Tokyo 103-0023 (Japan); Takeda, T. [School of Allied Health Science, Kitasato University, 1-15-1 Kitasato, Minami-ku, Sagamihara City, Kanagawa 252-0373 (Japan); Tanaka, M.M.; Uchida, T. [High Energy Accelerator Research Organization, 1-1 Oho, Tsukuba City, Ibaraki 305-0801 (Japan); Open-It consortium (Japan); Watanabe, T. [School of Allied Health Science, Kitasato University, 1-15-1 Kitasato, Minami-ku, Sagamihara City, Kanagawa 252-0373 (Japan); Open-It consortium (Japan); Yanagita, S.; Yoshida, T.; Umehara, K. [College of Science, Ibaraki University, 2-1-1 Bunkyo, Mito City, Ibaraki 310-8512 (Japan); Open-It consortium (Japan)

2015-12-21

We have developed a novel low-cost gamma-ray imaging Compton camera γI that has a high detection efficiency. Our motivation for the development of this detector was to measure the arrival directions of gamma rays produced by radioactive nuclides that were released by the Fukushima Daiichi nuclear power plant accident in 2011. The detector comprises two arrays of inorganic scintillation detectors, which act as a scatterer and an absorber. Each array has eight scintillation detectors, each comprising a large CsI (Tl) scintillator cube of side 3.5 cm, which is inexpensive and has a good energy resolution. Energies deposited by the Compton scattered electrons and subsequent photoelectric absorption, measured by each scintillation counter, are used for image reconstruction. The angular resolution was found to be 3.5° after using an image-sharpening technique. With this angular resolution, we can resolve a 1 m{sup 2} radiation hot spot that is located at a distance of 10 m from the detector with a wide field of view of 1 sr. Moreover, the detection efficiency 0.68 cps/MBq at 1 m for 662 keV (7.6 cps/μSv/h) is sufficient for measuring low-level contamination (i.e., less than 1 μSv/h) corresponding to typical values in large areas of eastern Japan. In addition to the laboratory tests, the imaging capability of our detector was verified in various regions with dose rates less than 1 μSv/h (e.g., Fukushima city).

Differential determination of 203Hg and 14C or 35S in double labelled biological samples

International Nuclear Information System (INIS)

Bem, E.M.; Bem, H.; Reimschussel, W.

1979-01-01

The differential determination of 203 Hg and 14 C or 35 S in double labelled biological samples is presented. The biological samples were mineralized with 70% HClO 4 and 30% H 2 O 2 in glass vials, MILLI-6. The γ-activity of 203 Hg was measured on a well scintillation counter. The total activity, due to 203 Hg and 14 C or 35 S, was measured by the liquid scintillation technique after addition of Aquasol into the same vials. The method of external standard channel ratio was used for standardization. Very good recoveries were obtained: 100+-0.7% for 203 Hg and 94.6-101.0% for 14 C and 35 S. This method could be used for other β, γ and β-active nuclides with similar β-spectra. (author)

The stringing of Italian keyboard instruments c.1500- c.1650. Part One: Discussion and bibliography

Science.gov (United States)

Wraight, Ralph Denzil

1997-12-01

The problem of deciding which stringing materials were used on Italian string keyboard instruments is approached in two ways, by examination of documentary evidence and through the evidence of the instruments. Information on 748 instruments is presented in a catalogue which examines and describes the original condition. 89 new attributions of instruments are presented. From this comprehensive pool of information on the compasses and string lengths of the instruments made it is argued that previous authors worked with too little information to enable accurate conclusions to be drawn. Documentary evidence alone is held to be inconclusive in showing which string material was used for particular instruments at specific periods, and not as useful as argued by some previous authors. The scaling design of instruments is considered and conclusions are advanced that most virginals were designed to be strung with iron wire. It is also argued that most 16th-century harpsichords were intended to be strung with iron wire. A change to brass- scaled designs took place from about 1600-1650, and this also coincided with a loss of popularity of designs employing a 4' stop. The orientation of the first and last notes of Italian compasses on c and f notes is argued to be a consequence of music theory and not a sure indication of pitch level. There were some 16th-century harpsichords made for a pitch a fourth lower than other 8' instruments, but it is argued that there were not two groups a fourth apart in pitch. The string lengths used in the cities of Venice, Florence, Rome, Milan, and Naples are listed and show that a normal 8' range covering a whole tone was in use in all areas at various times. The evidence of the string lengths suggests that instrument makers organised the pitches of instruments into 1/3 tone steps, a scheme which may be related to the apparent use of a 1/3 comma meantone tuning system in an organ of 1494 and clavichord of 1543, before it was described in print

Durability and CMAS Resistance of Advanced Environmental Barrier Coatings Systems for SiC/SiC Ceramic Matrix Composites

Science.gov (United States)

Zhu, Dongming

2015-01-01

Environmental barrier coatings (EBCs) and SiCSiC ceramic matrix composites (CMCs) systems will play a crucial role in next generation turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures with improved efficiency, reduce engine weight and cooling requirements. This paper will emphasize advanced environmental barrier coating developments for SiCSiC turbine airfoil components, by using advanced coating compositions and processing, in conjunction with mechanical and environment testing and durability validations. The coating-CMC degradations and durability in the laboratory simulated engine fatigue-creep and complex operating environments are being addressed. The effects of Calcium-Magnesium-Alumino-Silicate (CMAS) from road sand or volcano-ash deposits on the degradation mechanisms of the environmental barrier coating systems will be discussed. The results help understand the advanced EBC-CMC system performance, aiming at the durability improvements of more robust, prime-reliant environmental barrier coatings for successful applications of the component technologies and lifing methodologies.

The upgraded control and instrumentation system of C5 irradiation device

International Nuclear Information System (INIS)

Iordache, A.; Ancuta, M.; Gruia, L.; Pulpa, A.; Salistean, E.; Gusescu, G.

2013-01-01

C5 capsule is an irradiation device of TRIGA SSR, which is designed for irradiation of structural materials in an inert environment for mechanical behavior characterization and the material microstructure evolution during irradiation. The paper presents the upgraded control and instrumentation system of the C5 irradiation device which was designed and manufactured to enhance the performance of this system for better surveillance and processing the acquired experimental data. (authors)

CARMENES instrument overview

Science.gov (United States)

Quirrenbach, A.; Amado, P. J.; Caballero, J. A.; Mundt, R.; Reiners, A.; Ribas, I.; Seifert, W.; Abril, M.; Aceituno, J.; Alonso-Floriano, F. J.; Ammler-von Eiff, M.; Antona Jiménez, R.; Anwand-Heerwart, H.; Azzaro, M.; Bauer, F.; Barrado, D.; Becerril, S.; Béjar, V. J. S.; Benítez, D.; Berdiñas, Z. M.; Cárdenas, M. C.; Casal, E.; Claret, A.; Colomé, J.; Cortés-Contreras, M.; Czesla, S.; Doellinger, M.; Dreizler, S.; Feiz, C.; Fernández, M.; Galadí, D.; Gálvez-Ortiz, M. C.; García-Piquer, A.; García-Vargas, M. L.; Garrido, R.; Gesa, L.; Gómez Galera, V.; González Álvarez, E.; González Hernández, J. I.; Grözinger, U.; Guàrdia, J.; Guenther, E. W.; de Guindos, E.; Gutiérrez-Soto, J.; Hagen, H.-J.; Hatzes, A. P.; Hauschildt, P. H.; Helmling, J.; Henning, T.; Hermann, D.; Hernández Castaño, L.; Herrero, E.; Hidalgo, D.; Holgado, G.; Huber, A.; Huber, K. F.; Jeffers, S.; Joergens, V.; de Juan, E.; Kehr, M.; Klein, R.; Kürster, M.; Lamert, A.; Lalitha, S.; Laun, W.; Lemke, U.; Lenzen, R.; López del Fresno, Mauro; López Martí, B.; López-Santiago, J.; Mall, U.; Mandel, H.; Martín, E. L.; Martín-Ruiz, S.; Martínez-Rodríguez, H.; Marvin, C. J.; Mathar, R. J.; Mirabet, E.; Montes, D.; Morales Muñoz, R.; Moya, A.; Naranjo, V.; Ofir, A.; Oreiro, R.; Pallé, E.; Panduro, J.; Passegger, V.-M.; Pérez-Calpena, A.; Pérez Medialdea, D.; Perger, M.; Pluto, M.; Ramón, A.; Rebolo, R.; Redondo, P.; Reffert, S.; Reinhardt, S.; Rhode, P.; Rix, H.-W.; Rodler, F.; Rodríguez, E.; Rodríguez-López, C.; Rodríguez-Pérez, E.; Rohloff, R.-R.; Rosich, A.; Sánchez-Blanco, E.; Sánchez Carrasco, M. A.; Sanz-Forcada, J.; Sarmiento, L. F.; Schäfer, S.; Schiller, J.; Schmidt, C.; Schmitt, J. H. M. M.; Solano, E.; Stahl, O.; Storz, C.; Stürmer, J.; Suárez, J. C.; Ulbrich, R. G.; Veredas, G.; Wagner, K.; Winkler, J.; Zapatero Osorio, M. R.; Zechmeister, M.; Abellán de Paco, F. J.; Anglada-Escudé, G.; del Burgo, C.; Klutsch, A.; Lizon, J. L.; López-Morales, M.; Morales, J. C.; Perryman, M. A. C.; Tulloch, S. M.; Xu, W.

2014-07-01

fibers are continually actuated to reduce modal noise. The spectrographs are mounted on benches inside vacuum tanks located in the coudé laboratory of the 3.5m dome. Each vacuum tank is equipped with a temperature stabilization system capable of keeping the temperature constant to within +/-0.01°C over 24 hours. The visible-light spectrograph will be operated near room temperature, while the near-IR spectrograph will be cooled to ~ 140 K. The CARMENES instrument passed its final design review in February 2013. The MAIV phase is currently ongoing. First tests at the telescope are scheduled for early 2015. Completion of the full instrument is planned for the fall of 2015. At least 600 useable nights have been allocated at the Calar Alto 3.5m Telescope for the CARMENES survey in the time frame until 2018. A data base of M stars (dubbed CARMENCITA) has been compiled from which the CARMENES sample can be selected. CARMENCITA contains information on all relevant properties of the potential targets. Dedicated imaging, photometric, and spectroscopic observations are underway to provide crucial data on these stars that are not available in the literature.

Novel Control Strategy for VSI and CSI Active Filters and Comparing These Two Types of Filters

Directory of Open Access Journals (Sweden)

Gholam Reza Arab

2014-10-01

Full Text Available Recently to eliminate the harmonics and improve the power factor of the power networks, much attention has been attracted to active filters. The advantages of these filters are lower volume and their better compensating characteristics than the passive filters. In conventional sliding mode controllers, the source current waveform is fluctuated in near to zero values. In this paper, using a new sliding technique, lower Total Harmonic Distortion (THD in source current is obtained and the current waveform is improved. As well as, two novel control strategies for two types of active filters, VSI and CSI is proposed and then these two types of filters are compared to reduce THD value of source current.The proposed controlled strategies are simulated by MATLAB/Simulink. The Simulation results confirm that the proposed strategies reduce the THD of source current more than other strategies, and active filter based on CSI has a better performance than active filter based on VSI with a dead time area (for avoiding short circuit of the source in high powers.

Unusual Δ7,12,19 C35:3 Alkenone Produced by the Mutant Emiliania huxleyi strain CCMP2758 in Culture

Science.gov (United States)

Zheng, Y.; Huang, Y.; Zhang, Y.; Dillon, J. T.

2015-12-01

Alkenones with chain length ranging from C37 to C40 are highly specific biomarkers for certain haptophyte algae in ocean and lake sediments and have been widely used for paleoclimate studies. Short chain alkenones (e.g., C35 and C36) have been found in environmental and culture samples but the origin and structures of these compounds are not fully understood. The benchmark marine alkenone producer, Emiliania huxleyi CCMP2758 strain (the mutant of strain CCMP1742, NEPCC55a) was reported to make 35:2 alkenone when cultured at 15 °C (Prahl et al., 2006). Here we show, when this strain is cultured at lower temperatures (e.g., 4°C), CCMP2758 produces large amount of 35:3 alkenone with unusual double bond positions of Δ7,12,19. We determined the double bond positions of the C35:3 methyl ketonee based on GC-MS analysis of cyclobutylimine derivatives and dimethyl disulfide derivatives respectively, and provide the first temperature calibrations based on the unsaturation ratios of C35 alkenones. Previous studies have found 35:2 alkenone with three methylene interruption in the Black Sea sediment, but it is the first time that an alkenone with a mixed three and five methylene interruption is found. The discovery of short chain alkenones with unusual double bond positions may shed new light to alkenone biosynthesis.

[The CSI effect and its impact on the perceptions of forensic science experts' work].

Science.gov (United States)

Stojer, Joanna

2011-01-01

The issue that has been analyzed in this work is the potential effect of crime films and TV series on people's perceptions of forensic medicine and science, and especially on the forming of expectations towards forensic science experts. This syndrome is being called the "CSI effect" after the popular franchise Crime Scene Investigation (CSI). Questionnaire surveys that have been conducted included "experts": 50 experts in various specialities, 77 prosecutors, 119 judges, 64 lay judges, 161 police staff and 80 members of general public. In-depth interviews have been conducted with 20 police staff, and also a focus group has been carried out with 15 law students. In the opinion of the respondents, people's perceptions and expectations of forensic science--as it can be observed during criminal trials--are largely inflated by the entertainment media. Among the surveyed persons, the category that declares watching crime series most rarely, is forensic science experts. Around half of the surveyed experts pointed out to excessive expectations towards they work instigated by TV crime series. The most common expectations towards forensic medicine experts are: immediate conclusiveness of post mortem examinations (going as far as indicating the cause of death at the crime scene), precision of death time estimation and a routine use of sophisticated methods known from TV.

Optoelectrical modeling of solar cells based on c-Si/a-Si:H nanowire array: focus on the electrical transport in between the nanowires

Science.gov (United States)

Levtchenko, Alexandra; Le Gall, Sylvain; Lachaume, Raphaël; Michallon, Jérôme; Collin, Stéphane; Alvarez, José; Djebbour, Zakaria; Kleider, Jean-Paul

2018-06-01

By coupling optical and electrical modeling, we have investigated the photovoltaic performances of p-i-n radial nanowires array based on crystalline p-type silicon (c-Si) core/hydrogenated amorphous silicon (a-Si:H) shell. By varying either the doping concentration of the c-Si core, or back contact work function we can separate and highlight the contribution to the cell’s performance of the nanowires themselves (the radial cell) from the interspace between the nanowires (the planar cell). We show that the build-in potential (V bi) in the radial and planar cells strongly depends on the doping of c-Si core and the work function of the back contact respectively. Consequently, the solar cell’s performance is degraded if either the doping concentration of the c-Si core, or/and the work function of the back contact is too low. By inserting a thin (p) a-Si:H layer between both core/absorber and back contact/absorber, the performance of the solar cell can be improved by partly fixing the V bi at both interfaces due to strong electrostatic screening effect. Depositing such a buffer layer playing the role of an electrostatic screen for charge carriers is a suggested way of enhancing the performance of solar cells based on radial p-i-n or n-i-p nanowire array.

Influencia del método de dispersión del suelo en la calidad de materia orgánica separada por fraccionamiento granulométrico Influence of soil dispersion method on organic matter quality separated by particle-size fractionation

Directory of Open Access Journals (Sweden)

Cecilia Videla

2008-07-01

Full Text Available El fraccionamiento granulométrico de la materia orgánica (MO se basa en que las fracciones asociadas con partículas de diferente tamaño difieren en estructura y funciones y cumplen diferentes roles en el reciclado de la misma. El objetivo del presente trabajo fue comprobar la calidad del fraccionamiento de la MO de un Molisol a través del uso de: a agua y b hexametafosfato de sodio (HMP como dispersantes y analizar la distribución del C y N y los valores de δ13C en las distintas fracciones separadas. Se compararon la distribución de la fracción mineral del suelo con la MO destruida por calentamiento con agua oxigenada vs. dispersión en agua o dispersión con HMP. Las suspensiones de suelo fueron tamizadas por tamices de 200, 50 y 20 μm y la fraccion >200 μm fue separada en liviana y pesada por flotacion en agua. Las recuperaciones acumuladas de la masa de suelo (98,4 - 99,7%, N (87,4 - 99,4% y C (91,4 - 96,2% fueron altas en general, si bien el agua produjo mayores recuperaciones y HMP presentó mayor variabilidad. El HMP dispersó los agregados de la fracción >200 μm, permitiendo comprobar la gran cantidad de N y C que se acumula en las fracciones más finas, mientras que el agua no dispersó adecuadamente estos agregados. Gran cantidad de N quedó en la fracción Particle-size fractionation is supported by the concept that soil organic matter (SOM fractions associated with different mineral particle sizes have different structure and functions, and play different functions in SOM turnover. The objective of this work was to verify the quality of the organic matter fractionation of a Molisol dispersed with water or Na-hexametaphosphate (HMP and to analyze the C and N distribution and δ13C values of the separated fractions. We compared the mineral fraction distribution of the soil by completely oxidizing SOM through heating with hydrogen peroxide (AGUAOX versus water dispersion and HMP dispersion. The soil suspension was wet

Experiences with liquid scintillation counting of 3H, 14C and 35S from plant material

International Nuclear Information System (INIS)

Das, S.K.

1974-01-01

Relative merits of different methods in radioassay of three soft beta emitting isotopes like 3 H, 14 C and 35 S from plant material have been assessed. The methods used are: (1) combustion method (2) use of tissue solubilizing agents and (3) wet digestion method. Results show that determinations of 14 C by combustion method; 3 H by combustion and Mahin and Lofberg's method; and 35 S by wet digestion method are superior for plant material than the other methods tried. (author)

Report of the Instrumentation Service - Annex C

International Nuclear Information System (INIS)

Majstorovic, D.

1987-01-01

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment related to experimental facilities [sr

The Chinese Family Assessment Instrument (C-FAI): Hierarchical Confirmatory Factor Analyses and Factorial Invariance

Science.gov (United States)

Shek, Daniel T. L.; Ma, Cecilia M. S.

2010-01-01

Objective: This paper examines the dimensionality and factorial invariance of the Chinese Family Assessment Instrument (C-FAI) using multigroup confirmatory factor analyses (MCFAs). Method: A total of 3,649 students responded to the C-FAI in a community survey. Results: Results showed that there are five dimensions of the C-FAI (communication,…

Structure-function analysis of STING activation by c[G(2',5')pA(3',5')p] and targeting by antiviral DMXAA.

Science.gov (United States)

Gao, Pu; Ascano, Manuel; Zillinger, Thomas; Wang, Weiyi; Dai, Peihong; Serganov, Artem A; Gaffney, Barbara L; Shuman, Stewart; Jones, Roger A; Deng, Liang; Hartmann, Gunther; Barchet, Winfried; Tuschl, Thomas; Patel, Dinshaw J

2013-08-15

Binding of dsDNA by cyclic GMP-AMP (cGAMP) synthase (cGAS) triggers formation of the metazoan second messenger c[G(2',5')pA(3',5')p], which binds the signaling protein STING with subsequent activation of the interferon (IFN) pathway. We show that human hSTING(H232) adopts a "closed" conformation upon binding c[G(2',5')pA(3',5')p] and its linkage isomer c[G(2',5')pA(2',5')p], as does mouse mSting(R231) on binding c[G(2',5')pA(3',5')p], c[G(3',5')pA(3',5')p] and the antiviral agent DMXAA, leading to similar "closed" conformations. Comparing hSTING to mSting, 2',5'-linkage-containing cGAMP isomers were more specific triggers of the IFN pathway compared to the all-3',5'-linkage isomer. Guided by structural information, we identified a unique point mutation (S162A) placed within the cyclic-dinucleotide-binding site of hSTING that rendered it sensitive to the otherwise mouse-specific drug DMXAA, a conclusion validated by binding studies. Our structural and functional analysis highlights the unexpected versatility of STING in the recognition of natural and synthetic ligands within a small-molecule pocket created by the dimerization of STING. Copyright © 2013 Elsevier Inc. All rights reserved.

1D cyanide complexes with 2-pyridinemethanol: Synthesis, crystal structures and spectroscopic properties

Science.gov (United States)

Sayın, Elvan; Kürkçüoğlu, Güneş Süheyla; Yeşilel, Okan Zafer; Hökelek, Tuncer

2015-12-01

Two new one-dimensional coordination polymers, [Cu(hmpH)2Pd(μ-CN)2(CN)2]n (1) and [Cu(hmpH)2Pt(μ-CN)2(CN)2]n (2), (hmpH = 2-pyridinemethanol), have been synthesized and characterized by vibrational (FT-IR and Raman) spectroscopy, single crystal X-ray diffraction, thermal and elemental analyses techniques. Single crystal X-ray diffraction analysis indicates that complexes 1 and 2 are isomorphous and isostructural, and crystallize in the triclinic system and P-1 space group. The Pd(II) or Pt(II) ions are four coordinated with four cyanide-carbon atoms in a square planar geometry. Cu(II) ion displays a distorted octahedral coordination by two N-atoms and two O-atoms of hmpH ligands, two bridging cyanide groups. In one dimensional structure of the complexes, [M(CN)4]2- (M = Pd(II) or Pt(II)) anions and [Cu(hmpH)2]2+ cations are linked via bridging cyanide ligands. In the complexes, the presence of intramolecular C-H⋯M (M = Pd(II) or Pt(II)) interactions with distance values of 3.00-2.95 Å are established, respectively.

Contrast source inversion (CSI) method to cross-hole radio-imaging (RIM) data - Part 2: A complex synthetic example and a case study

Science.gov (United States)

Li, Yongxing; Smith, Richard S.

2018-03-01

We present two examples of using the contrast source inversion (CSI) method to invert synthetic radio-imaging (RIM) data and field data. The synthetic model has two isolated conductors (one perfect conductor and one moderate conductor) embedded in a layered background. After inversion, we can identify the two conductors on the inverted image. The shape of the perfect conductor is better resolved than the shape of the moderate conductor. The inverted conductivity values of the two conductors are approximately the same, which demonstrates that the conductivity values cannot be correctly interpreted from the CSI results. The boundaries and the tilts of the upper and the lower conductive layers on the background can also be inferred from the results, but the centre parts of conductive layers in the inversion results are more conductive than the parts close to the boreholes. We used the straight-ray tomographic imaging method and the CSI method to invert the RIM field data collected using the FARA system between two boreholes in a mining area in Sudbury, Canada. The RIM data include the amplitude and the phase data collected using three frequencies: 312.5 kHz, 625 kHz and 1250 kHz. The data close to the ground surface have high amplitude values and complicated phase fluctuations, which are inferred to be contaminated by the reflected or refracted electromagnetic (EM) fields from the ground surface, and are removed for all frequencies. Higher-frequency EM waves attenuate more quickly in the subsurface environment, and the locations where the measurements are dominated by noise are also removed. When the data are interpreted with the straight-ray method, the images differ substantially for different frequencies. In addition, there are some unexpected features in the images, which are difficult to interpret. Compared with the straight-ray imaging results, the inversion results with the CSI method are more consistent for different frequencies. On the basis of what we learnt

Drying characteristics of hui ink at 25 °C and 35 °C

Science.gov (United States)

Fu, Yang; Yao, Yao; Liu, Le; Wang, Fengwen; Yang, Shuyun

2018-05-01

Temperature and humidity are the main factors affecting the drying of Hui ink. For the experiment, fresh Hui ink billets from two big ink industries were selected. We tried to find the fast and efficient drying conditions of Hui ink and calculate effective diffusion coefficient by performing manual control of temperature and relative humidity (RH). Several dry kinetic models were fitted. A constant temperature incubator was utilized for temperature control, while humidification and dehumidification were implemented accordingly for RH control. Setups of 25 °C and 35 °C were designed, and a relative humidity of 60%, 65%, 70%, and 75% was applied for each temperature. The process of ink drying was recorded, and the drying effect of Hui ink was estimated through expert decision. The appropriate drying temperature and humidity of the Jinbuhuan(J) and Huangshansongyan(H) ink billets from Lao Hu Kai Wen Ink Industry are at (31.99 ± 1.41) °C and (55.84 ± 10.38)% RH, whereas those of the Songyantanhei(ST), Chunyouyan(CY), and Quansongyan(QS) ink billets from Ju Mo Tang Ink Industry are at (23.70 ± 2.19) °C and (60.56 ± 2.16)% RH or (34.56 ± 2.37) °C and (59.16 ± 6.38)% RH; Initial moisture content of Hui ink has great influence on the water loss in the drying process; The effective diffusion coefficient of the ink lump ranges from 8.41538E-07 to 1.95891E-06 m2·s-1, and increases mainly with the temperature's rising; Logarithmic model fits best of the chosen models.

Solvent extraction of Cs(I), Zn(II), Eu(III) and Am(III) by 2-heptyl-2-methyl-nonanoic acid (Ha) from nitrate solutions

International Nuclear Information System (INIS)

Ramadan, A.; Elnaggar, H.A.; Souka, N.; Abdelfattah, A.

1994-01-01

The present work is devoted to study the extraction behavior of caesium, zinc, europium and americium radioactive isotopes using a new extractant C H 3 (C H 2 ) 6 . C(C 7 H 1 5) (C H 3 ). COOH (Ha) dissolved in benzene from aqueous nitrate media of constant ionic strength (0.1 M) using HNO 3 -Na NO 3 mixtures. The effect temperature on the extraction of these elements was also investigated to evaluate the thermodynamic functions as well as the equilibrium constant of each reaction. The extraction mechanisms were postulated on the light of the available data and the extracted species were formulated in the proposed stoichiometric equation for the extraction of each element individually and these species were suggested to be Cs (A); Zn OH(A) and Zn(A) 2 ; Eu No 3 (A) 2 and Am(A) 3 and for Cs(I), Zn(II), Eu(III) and Am(III), respectively. The thermodynamic parameters show exothermic enthalpy for all the reactions and negative entropy values reflecting very good ordering extraction mechanisms. 10 figs, 1 tab

Evaluation of various planar gaseous detectors with CsI photocathodes for the detection of primary scintillation light from noble gases

CERN Document Server

Periale, L; Carlson, P J; Francke, T; Iacobaeus, C; Pavlopoulos, P; Pietropaolo, F; Sokolova, T

2003-01-01

Noble gases and liquids are excellent scintillators and this opens a unique opportunity to directly detect the primary scintillation light produced in these media by photons or particles. This signal can be used for several purposes, for example as a start signal for TPCs or for particles identification. Usually photomultipliers (PMs) are used for the detection of the scintillation light. In our previous work we have demonstrated that costly PMs could be replaced by gaseous detectors with CsI photocathodes . Such detectors have the same quantum efficiency as the best PMs but at the same time are cheap, simple and have high position and time resolutions. The aim of this work is to evaluate various planar type gaseous detectors with CsI photocahodes in order to choose the best one for the detection of the primary scintillation light from noble gases and liquids.

Photoelectron extraction efficiency from a CsI photocathode and THGEM operation in He−CF4 and He−CH4 mixtures

International Nuclear Information System (INIS)

Coimbra, A.E.C.; Santos, J.M.F. dos; Israelashvili, I.

2016-01-01

This work presents the experimental measurements obtained for UV-induced photo-electron extraction efficiency from a CsI photocathode into He with CF 4 and CH 4 gas mixtures. A 1000Å CsI photocathode was deposited on a gold plated THGEM for photo-electron conversion. Charge-gain measurements were obtained with a Single-THGEM detector operating in these gas mixtures using a continuous UV lamp for the extraction of photo-electrons. Charge-gains in excess of 10 5 were obtained for gas mixtures containing percentages of quencher higher than 20% while photo-electron extraction efficiency achieved ∼ 50% for He/CF 4 and ∼ 30% for He/CH 4 . Single photon electron measurements were also performed to assess the maximal gains reached in this regime. A discussion for future GPM cryogenic applications is presented

Security-Reliability Analysis of Noma-Based Multi-Hop Relay Networks in Presence of an Active Eavesdropper with Imperfect Eavesdropping CSI

Directory of Open Access Journals (Sweden)

Tran Tin Phu

2017-01-01

Full Text Available In this paper, we evaluate system performances of a multi-hop relay protocol with presence of an active eavesdropper. In the proposed protocol, a source attempts to transmit its data to a destination with assistance of multiple intermediate relays. From the eavesdropping Channel State Information (CSI estimated, the source and relays adjust their transmit power so that the eavesdropper cannot overhear the transmitted data. Moreover, to enhance throughput for the proposed system, Non-Orthogonal Multiple Access (NOMA technique with a simple power allocation is also proposed. We derive exact closed-form expressions of the Outage Probability (OP and throughput for the data transmission over Rayleigh fading channel. In addition, when the CSI estimation is imperfect, Intercept Probability (IP at the eavesdropper is derived. Finally, Monte Carlo simulations are presented to verify the theoretical derivations.

Charter Schools Indicators: A Report from the Center on Educational Governance University of Southern California. CSI-USC 2010

Science.gov (United States)

Center on Educational Governance, 2010

2010-01-01

CSI-USC continues to make sense of what the California statewide data system provides. This fourth annual report gauges multiple measures of academic and financial performance, probing well beyond mere test scores. Ratings in familiar green, yellow, and red cover four areas: financial resources and investment, school quality, student performance…

Instrument Control (iC) - An Open-Source Software to Automate Test Equipment.

Science.gov (United States)

Pernstich, K P

2012-01-01

It has become common practice to automate data acquisition from programmable instrumentation, and a range of different software solutions fulfill this task. Many routine measurements require sequential processing of certain tasks, for instance to adjust the temperature of a sample stage, take a measurement, and repeat that cycle for other temperatures. This paper introduces an open-source Java program that processes a series of text-based commands that define the measurement sequence. These commands are in an intuitive format which provides great flexibility and allows quick and easy adaptation to various measurement needs. For each of these commands, the iC-framework calls a corresponding Java method that addresses the specified instrument to perform the desired task. The functionality of iC can be extended with minimal programming effort in Java or Python, and new measurement equipment can be addressed by defining new commands in a text file without any programming.

Cellulose synthesis genes CESA6 and CSI1 are important for salt stress tolerance in Arabidopsis.

Science.gov (United States)

Zhang, Shuang-Shuang; Sun, Le; Dong, Xinran; Lu, Sun-Jie; Tian, Weidong; Liu, Jian-Xiang

2016-07-01

Two salt hypersensitive mutants she1 and she2 were identified through genetic screening. SHE1 encodes a cellulose synthase CESA6 while SHE2 encodes a cellulose synthase-interactive protein CSI1. Both of them are involved in cellulose deposition. Our results demonstrated that the sustained cellulose synthesis is important for salt stress tolerance in Arabidopsis. © 2015 Institute of Botany, Chinese Academy of Sciences.

Metabolism and excretion of 1-hydroxymethylpyrene, the proximate metabolite of the carcinogen 1-methylpyrene, in rats

International Nuclear Information System (INIS)

Bendadani, Carolin; Steinhauser, Lisa; Albert, Klaus; Glatt, Hansruedi; Monien, Bernhard H.

2016-01-01

1-Methylpyrene, an alkylated polycyclic aromatic hydrocarbon and environmental carcinogen, is activated by side-chain hydroxylation to 1-hydroxymethylpyrene (1-HMP) and subsequent sulfo conjugation to the DNA-reactive 1-sulfooxymethylpyrene. In addition to the bioactivation, processes of metabolic detoxification and transport greatly influence the genotoxicity of 1-methylpyrene. For a better understanding of 1-HMP detoxification in vivo we studied urinary and fecal metabolites in rats following intraperitoneal doses of 19.3 mg 1-HMP/kg body weight (5 rats) or the same dose containing 200 μCi [ 14 C]1-HMP/kg body weight (2 rats). After 48 h, 48.0% (rat 1) and 29.1% (rat 2) of the radioactivity was recovered as 1-HMP in the feces. Six major metabolites were observed by UV and on-line radioactivity detection in urine samples and feces after HPLC separation. The compounds were characterized by mass spectrometry, 1 H NMR and 1 H- 1 H COSY NMR spectroscopy, which allowed assigning tentative molecular structures. Two prominent metabolites, 1-pyrene carboxylic acid (M-6) and the acyl glucuronide of 1-pyrene carboxylic acid (M-5) accounted for 17.7% (rat 1) and 25.2% (rat 2) of the overall radioactive dose. Further, we detected the acyl glucuronide of 6-hydroxy-1-pyrene carboxylic acid (M-1) and 8-sulfooxy-1-pyrene carboxylic acid (M-3) together with two regioisomers of M-3 (M-2 and M-4) differing in position of the sulfate group at the pyrene ring. In urine samples, the radioactivity of 1-pyrene carboxylic acid and its five derivatives amounted to 32.4% (rat 1) or 45.5% (rat 2) of the total [ 14 C]1-HMP dose.

Report of the Instrumentation Service - Annex C

International Nuclear Information System (INIS)

Mikic, N.; Majstorovic, D.

1993-01-01

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related to renewal of the equipment [sr

Report of the Instrumentation Service - Annex C

International Nuclear Information System (INIS)

Mikic, N.

1999-01-01

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related control and maintenace of the experimental devices [sr

Report of the Instrumentation Service - Annex C

International Nuclear Information System (INIS)

Mikic, N.

2000-01-01

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related control and maintenace of the experimental devices [sr

Report of the Instrumentation Service - Annex C

International Nuclear Information System (INIS)

Majstorovic, D.

1986-01-01

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related to renewal of the equipment [sr

Report of the Instrumentation Service - Annex C

International Nuclear Information System (INIS)

Majstorovic, D.

1988-01-01

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related to renewal of the equipment [sr

Investigation of 3C-SiC/SiO2 interfacial point defects from ab initio g-tensor calculations and electron paramagnetic resonance measurements

Science.gov (United States)

Nugraha, T. A.; Rohrmueller, M.; Gerstmann, U.; Greulich-Weber, S.; Stellhorn, A.; Cantin, J. L.; von Bardeleben, J.; Schmidt, W. G.; Wippermann, S.

SiC is widely used in high-power, high-frequency electronic devices. Recently, it has also been employed as a building block in nanocomposites used as light absorbers in solar energy conversion devices. Analogous to Si, SiC features SiO2 as native oxide that can be used for passivation and insulating layers. However, a significant number of defect states are reported to form at SiC/SiO2 interfaces, limiting mobility and increasing recombination of free charge carriers. We investigated the growth of oxide on different 3C-SiC surfaces from first principles. Carbon antisite Csi defects are found to be strongly stabilized in particular at the interface, because carbon changes its hybridization from sp3 in the SiC-bulk to sp2 at the interface, creating a dangling bond inside a porous region of the SiO2 passivating layer. Combining ab initio g-tensor calculations and electron paramagnetic resonance (EPR) measurements, we show that Csi defects explain the measured EPR signatures, while the hyperfine structure allows to obtain local structural information of the oxide layer. Financial support from BMBF NanoMatFutur Grant 13N12972 and DFG priority program SPP-1601 is gratefully acknowledged.

Metabolic and Physiological Responses of Shiraz and Cabernet Sauvignon (Vitis vinifera L. to Near Optimal Temperatures of 25 and 35 °C

Directory of Open Access Journals (Sweden)

Uri Hochberg

2015-10-01

Full Text Available Shiraz and Cabernet Sauvignon (Cs grapevines were grown at near optimal temperatures (25 or 35 °C. Gas exchange, fluorescence, metabolic profiling and correlation based network analysis were used to characterize leaf physiology. When grown at 25 °C, the growth rate and photosynthesis of both cultivars were similar. At 35 °C Shiraz showed increased respiration, non-photochemical quenching and reductions of photosynthesis and growth. In contrast, Cs maintained relatively stable photosynthetic activity and growth regardless of the condition. In both cultivars, growth at 35 °C resulted in accumulations of secondary sugars (raffinose, fucose and ribulose and reduction of primary sugars concentration (glucose, fructose and sucrose, more noticeably in Shiraz than Cs. In spite of similar patterns of metabolic changes in response to growth at 35 °C, significant differences in important leaf antioxidants and antioxidant precursors (DHA/ascorbate, quinates, cathechins characterized the cultivar response. Correlation analysis reinforced Shiraz sensitivity to the 35 °C, showing higher number of newly formed edges at 35 °C and higher modularity in Shiraz as compared to Cs. The results suggest that the optimal growth temperatures of grapevines are cultivar dependent, and allow a first insight into the variability of the metabolic responses of grapevines under varied temperatures.

Metabolic and Physiological Responses of Shiraz and Cabernet Sauvignon (Vitis vinifera L.) to Near Optimal Temperatures of 25 and 35 °C.

Science.gov (United States)

Hochberg, Uri; Batushansky, Albert; Degu, Asfaw; Rachmilevitch, Shimon; Fait, Aaron

2015-10-14

Shiraz and Cabernet Sauvignon (Cs) grapevines were grown at near optimal temperatures (25 or 35 °C). Gas exchange, fluorescence, metabolic profiling and correlation based network analysis were used to characterize leaf physiology. When grown at 25 °C, the growth rate and photosynthesis of both cultivars were similar. At 35 °C Shiraz showed increased respiration, non-photochemical quenching and reductions of photosynthesis and growth. In contrast, Cs maintained relatively stable photosynthetic activity and growth regardless of the condition. In both cultivars, growth at 35 °C resulted in accumulations of secondary sugars (raffinose, fucose and ribulose) and reduction of primary sugars concentration (glucose, fructose and sucrose), more noticeably in Shiraz than Cs. In spite of similar patterns of metabolic changes in response to growth at 35 °C, significant differences in important leaf antioxidants and antioxidant precursors (DHA/ascorbate, quinates, cathechins) characterized the cultivar response. Correlation analysis reinforced Shiraz sensitivity to the 35 °C, showing higher number of newly formed edges at 35 °C and higher modularity in Shiraz as compared to Cs. The results suggest that the optimal growth temperatures of grapevines are cultivar dependent, and allow a first insight into the variability of the metabolic responses of grapevines under varied temperatures.

Chitin-Prussian blue sponges for Cs(I) recovery: From synthesis to application in the treatment of accidental dumping of metal-bearing solutions

Energy Technology Data Exchange (ETDEWEB)

Vincent, C. [Ecole des mines d' Alès, Centre des Matériaux des Mines d' Alès, C2MA/MPA/BCI, 6 avenue de Clavières, F-30319 Alès Cedex (France); Commissariat à l' Energie Atomique, CEA Marcoule, DEN/DTCD/SPDE/LPSD,BP 17171, F-30207 Bagnols sur Cèze (France); Barré, Y. [Commissariat à l' Energie Atomique, CEA Marcoule, DEN/DTCD/SPDE/LPSD,BP 17171, F-30207 Bagnols sur Cèze (France); Vincent, T. [Ecole des mines d' Alès, Centre des Matériaux des Mines d' Alès, C2MA/MPA/BCI, 6 avenue de Clavières, F-30319 Alès Cedex (France); Taulemesse, J.-M. [Ecole des mines d' Alès, Center des Matériaux des Mines d' Alès, 6 avenue de Clavières, F-30319 Alès Cedex (France); Robitzer, M. [Institut Charles Gerhardt – UMR5253, CNRS-UM2-ENSCM-UM1, ICGM-MACS-R2M2, 8 rue de l' Ecole Normale, F-34296 Montpellier Cedex 05 (France); Guibal, E., E-mail: Eric.Guibal@mines-ales.fr [Ecole des mines d' Alès, Centre des Matériaux des Mines d' Alès, C2MA/MPA/BCI, 6 avenue de Clavières, F-30319 Alès Cedex (France)

2015-04-28

Highlights: • Prussian blue microparticles incorporated in chitin sponges. • Efficient Cs(I) sorption after water absorption by dry hybrid sponge. • Water draining after sorption for metal confinement and water decontamination. • High decontamination factors and distribution coefficients for Cs(I) and {sup 137}Cs(I). • Effect of freezing conditions on porous structure and textural characterization. - Abstract: Prussian blue (i.e., iron[III] hexacyanoferrate[II], PB) has been synthesized by reaction of iron(III) chloride with potassium hexacyanoferrate and further immobilized in chitosan sponge (cellulose fibers were added in some samples to evaluate their impact on mechanical resistance). The composite was finally re-acetylated to produce a chitin-PB sponge. Experimental conditions such as the freezing temperature, the content of PB, the concentration of the biopolymer and the presence of cellulose fibers have been varied in order to evaluate their effect on the porous structure of the sponge, its water absorption properties and finally its use for cesium(I) recovery. The concept developed with this system consists in the absorption of contaminated water by the composite sponge, the in situ binding of target metal on Prussian blue load and the centrifugation of the material to remove treated water from soaked sponge. This material is supposed to be useful for the fast treatment of accidental dumping of Cs-contaminated water.

On the low SNR capacity of log-normal turbulence channels with full CSI

KAUST Repository

Benkhelifa, Fatma; Tall, Abdoulaye; Rezki, Zouheir; Alouini, Mohamed-Slim

2014-01-01

In this paper, we characterize the low signal-To-noise ratio (SNR) capacity of wireless links undergoing the log-normal turbulence when the channel state information (CSI) is perfectly known at both the transmitter and the receiver. We derive a closed form asymptotic expression of the capacity and we show that it scales essentially as λ SNR where λ is the water-filling level satisfying the power constraint. An asymptotically closed-form expression of λ is also provided. Using this framework, we also propose an on-off power control scheme which is capacity-achieving in the low SNR regime.

On the low SNR capacity of log-normal turbulence channels with full CSI

KAUST Repository

Benkhelifa, Fatma

2014-09-01

In this paper, we characterize the low signal-To-noise ratio (SNR) capacity of wireless links undergoing the log-normal turbulence when the channel state information (CSI) is perfectly known at both the transmitter and the receiver. We derive a closed form asymptotic expression of the capacity and we show that it scales essentially as λ SNR where λ is the water-filling level satisfying the power constraint. An asymptotically closed-form expression of λ is also provided. Using this framework, we also propose an on-off power control scheme which is capacity-achieving in the low SNR regime.

Performance study of single undoped CsI crystals for the Mu2e experiment

International Nuclear Information System (INIS)

Donghia, R.

2016-01-01

The Mu2e experiment at Fermilab aims to measure the neutrinoless muon-to-electron conversion, which is a charged-lepton flavor-violating process. The goal of the experiment is to reach a single event sensitivity of 2.5 × 10"−"1"7, to set an upper limit on the muon conversion rate at 6.7 × 10"−"1"7 in a three-year run. For this purpose, the Mu2e detector is designed to identify electrons from muon conversion and reduce the background to a negligible level. It consists of a low-mass straw tracker and a pure CsI crystal calorimeter. In this paper, the performance of undoped CsI single crystal is reported. Crystals from many vendors have been characterized by determining their Light Yield (LY) and Longitudinal Response Uniformity (LRU), when read with a UV extended PMT, and their time resolution when coupled to a silicon photomultiplier. The crystals show a LY of ∼ 100 photoelectrons per MeV when wrapped with Tyvek and coupled to the PMT without optical grease. The LRU is well represented by a linear slope that is on average 0.6%/cm. Both measurements have been performed using a "2"2Na source. The timing performance has been evaluated exploiting cosmic rays, with MPPC readout. A timing resolution lower than 400 ps has been achieved (at ∼ 20 MeV, which is the energy released by a minimum ionizing particle in the crystal).

Runtime Instrumentation of SystemC/TLM2 Interfaces for Fault Tolerance Requirements Verification in Software Cosimulation

Directory of Open Access Journals (Sweden)

Antonio da Silva

2014-01-01

Full Text Available This paper presents the design of a SystemC transaction level modelling wrapping library that can be used for the assertion of system properties, protocol compliance, or fault injection. The library uses C++ virtual table hooks as a dynamic binary instrumentation technique to inline wrappers in the TLM2 transaction path. This technique can be applied after the elaboration phase and needs neither source code modifications nor recompilation of the top level SystemC modules. The proposed technique has been successfully applied to the robustness verification of the on-board boot software of the Instrument Control Unit of the Solar Orbiter’s Energetic Particle Detector.

Use of natural diamonds to monitor 14C AMS instrument backgrounds

International Nuclear Information System (INIS)

Taylor, R.E.; Southon, John

2007-01-01

To examine one component of the instrument-based background in University of California Keck Carbon Cycle AMS spectrometer, we have obtained measurements on a set of natural diamonds pressed into sample holders. Natural diamond samples (N = 14) from different sources within rock formations with geological ages greatly in excess of 100 Ma yielded a range of currents (∼110-250 μA 12 C - where filamentous graphite typically yields ∼150 μA 12 C - ) and apparent 14 C ages (64.9 ± 0.4 ka BP [0.00031 ± 0.00002 fm] to 80.0 ± 1.1 ka BP [0.00005 ± 0.00001 fm]). Six fragments cut from a single diamond exhibited essentially identical 14 C values - 69.3 ± 0.5 ka-70.6 ± 0.5 ka BP. The oldest 14 C age equivalents were measured on natural diamonds which exhibited the highest current yields

High-performance a -Si/c-Si heterojunction photoelectrodes for photoelectrochemical oxygen and hydrogen evolution

KAUST Repository

Wang, Hsin Ping; Sun, Ke; Noh, Sun Young; Kargar, Alireza; Tsai, Meng Lin; Huang, Ming Yi; Wang, Deli; He, Jr-Hau

2015-01-01

Amorphous Si (a-Si)/crystalline Si (c-Si) heterojunction (SiHJ) can serve as highly efficient and robust photoelectrodes for solar fuel generation. Low carrier recombination in the photoelectrodes leads to high photocurrents and photovoltages

Protective Effect of HLA-B*5701 and HLA-C -35 Genetic Variants in HIV-Positive Caucasians from Northern Poland.

Directory of Open Access Journals (Sweden)

Magdalena Leszczyszyn-Pynka

Full Text Available Association of two HLA class I variants with HIV-1 pretreatment viremia, CD4+ T cell count at the care-entry and CD4+ T cell nadir.414 HIV-positive Caucasians (30% women aged 19-73 years were genotyped for HLA-C -35 (rs9264942 and HLA-B*5701 variants. HIV-1 viral load, as well as CD4+ T cell count at care-entry and nadir, were compared across alleles, genotypes and haplotypes.HLA-C -35 C/C genotype was found in 17.6% patients, C/T genotype in 48.1%, and T/T genotype in 34.3% patients. HLA-B*5701 variant was present in 5.8% of studied population. HIV plasma viremia in the group with C allele was significantly lower (p=0.0002 compared to T/T group [mean:4.66 log (SD:1.03 vs. 5.07 (SD:0.85 log HIV-RNA copies/ml, respectively], while CD4+ T cell count at baseline was notably higher among C allele carriers compared to T/T homozygotes [median: 318 (IQR:127-537 cells/μl vs. median: 203 (IQR:55-410 cells/μl, respectively] (p=0.0007. Moreover, CD4+ T cell nadir among patients with C allele [median: 205 (IQR:83.5-390 cells/μl] was significantly higher compared to T/T group [median: 133 (IQR:46-328 cells/μl] (p=0.006. Among cases with HLA-B*5701 allele, significantly lower pretreatment viremia and higher baseline CD4+ T cell count were found (mean: 4.08 [SD: 1.2] vs. mean: 4.84 [SD:0.97] log HIV-RNA copies/ml, p=0.003 and 431 vs. 270 cells/μl, p=0.04, respectively compared to HLA-B*5701 negative individuals. The lowest viremia (mean: 3.85 log [SD:1.3] HIV-RNA copies/ml and the highest baseline and nadir CD4+ T cell [median: 476 (IQR:304-682 vs. median: 361 (IQR: 205-574 cells/μl, respectively were found in individuals with HLA-B*5701(+/HLA-C -35 C/C haplotype.HLA-C -35 C and HLA-B*5701 allele exert a favorable effect on the immunological (higher baseline and nadir CD4+ T cell count and virologic (lower pretreatment HIV viral load variables. This protective effect is additive for the compound HLA-B*5701(+/HLA-C -35 C/C haplotype.

CSI Index Of Customer's Satisfaction Applied In The Area Of Public Transport

Science.gov (United States)

Poliaková, Adela

2015-06-01

In Western countries, the new visions are applied in quality control for an integrated public transport system. Public transport puts the customer at the centre of our decision making in achieving customer satisfaction with provided service. Sustainable surveys are kept among customers. A lot of companies are collecting huge databases containing over 30,000 voices of customers, which demonstrates the current satisfaction levels across the public transport service. Customer satisfaction with a provided service is a difficult task. In this service, the quality criteria are not clearly defined, and it is therefore difficult to define customer satisfaction. The paper introduces a possibility of CSI index application in conditions of the Slovak Republic transport area.

Dosimetric comparison between proton and photon beams in the moving gap region in cranio-spinal irradiation (CSI)

Energy Technology Data Exchange (ETDEWEB)

Cheng, Chee-Wai; Das, Indra J.; Zhao, Li; Wolanski, Mark; Johnstone, Peter A.S.; Buchsbaum, Jeffrey C. [IU Health Proton Therapy Center, Bloomington (United States); Dept. of Radiation Oncology, Indiana Univ. School of Medicine, Indianapolis (United States)], e-mail: ccheng1@iuhealth.org; Srivastava, Shiv P. [Dept. of Radiation Oncology, Indiana Univ. School of Medicine, Indianapolis (United States); Dept. of Radiation Oncology, Reid Hospital, Richmond (United States); Simmons, Joseph [IU Health Proton Therapy Center, Bloomington (United States)

2013-04-15

Purpose: To investigate the moving gap region dosimetry in proton beam cranio-spinal irradiation (CSI) to provide optimal dose uniformity across the treatment volume. Material and methods: Proton beams of ranges 11.6 cm and 16 cm are used for the spine and the brain fields, respectively. Beam profiles for a 30 cm snout are first matched at the 50% level (hot match) on the computer. Feathering is simulated by shifting the dose profiles by a known distance two successive times to simulate a 2 x feathering scheme. The process is repeated for 2 mm and 4 mm gaps. Similar procedures are used to determine the dose profiles in the moving gap for a series of gap widths, 0-10 mm, and feathering step sizes, 4-10 mm, for a Varian iX 6MV beam. The proton and photon dose profiles in the moving gap region are compared. Results: The dose profiles in the moving gap exhibit valleys and peaks in both proton and photon beam CSI. The dose in the moving gap for protons is around 100% or higher for 0 mm gap, for both 5 and 10 mm feathering step sizes. When the field gap is comparable or larger than the penumbra, dose minima as low as 66% is obtained. The dosimetric characteristics for 6 MV photon beams can be made similar to those of the protons by appropriately combining gap width and feathering step size. Conclusion: The dose in the moving gap region is determined by the lateral penumbras, the width of the gap and the feathering step size. The dose decreases with increasing gap width or decreasing feathering step size. The dosimetric characteristics are similar for photon and proton beams. However, proton CSI has virtually no exit dose and is beneficial for pediatric patients, whereas with photon beams the whole lung and abdomen receive non-negligible exit dose.

Experimental measurement of a high resolution CMOS detector coupled to CsI scintillators under X-ray radiation

International Nuclear Information System (INIS)

Michail, C.; Valais, I.; Seferis, I.; Kalyvas, N.; Fountos, G.; Kandarakis, I.

2015-01-01

The purpose of the present study was to assess the information content of structured CsI:Tl scintillating screens, specially treated to be compatible to a CMOS digital imaging optical sensor, in terms of the information capacity (IC), based on Shannon's mathematical communication theory. IC was assessed after the experimental determination of the Modulation Transfer Function (MTF) and the Normalized Noise Power Spectrum (NNPS) in the mammography and general radiography energy range. The CMOS sensor was coupled to three columnar CsI:Tl scintillator screens obtained from the same manufacturer with thicknesses of 130, 140 and 170 μm respectively, which were placed in direct contact with the optical sensor. The MTF was measured using the slanted-edge method while NNPS was determined by 2D Fourier transforming of uniformly exposed images. Both parameters were assessed by irradiation under the mammographic W/Rh (130, 140 and 170 μm CsI screens) and the RQA-5 (140 and 170 μm CsI screens) (IEC 62220-1) beam qualities. The detector response function was linear for the exposure range under investigation. At 70 kVp, under the RQA-5 conditions IC values were found to range between 2229 and 2340 bits/mm 2 . At 28 kVp the corresponding IC values were found to range between 2262 and 2968 bits/mm 2 . The information content of CsI:Tl scintillating screens in combination to the high resolution CMOS sensor, investigated in the present study, where found optimized for use in digital mammography imaging systems. - Highlights: • Three structured CsI:Tl screens (130,140 & 170 um) were coupled to a CMOS sensor. • MTF of the CsI/CMOS was higher than GOS:Tb and CsI based digital imaging systems. • IC of CsI:Tl/CMOS was found optimized for use in digital mammography systems

Property Evaluation and Damage Evolution of Environmental Barrier Coatings and Environmental Barrier Coated SiC/SiC Ceramic Matrix Composite Sub-Elements

Science.gov (United States)

Zhu, Dongming; Halbig, Michael; Jaskowiak, Martha; Hurst, Janet; Bhatt, Ram; Fox, Dennis S.

2014-01-01

This paper describes recent development of environmental barrier coatings on SiC/SiC ceramic matrix composites. The creep and fatigue behavior at aggressive long-term high temperature conditions have been evaluated and highlighted. Thermal conductivity and high thermal gradient cyclic durability of environmental barrier coatings have been evaluated. The damage accumulation and complex stress-strain behavior environmental barrier coatings on SiCSiC ceramic matrix composite turbine airfoil subelements during the thermal cyclic and fatigue testing of have been also reported.

Project C-018H, 242-A evaporator/PUREX Plant Process Condensate Treatment Facility Instrumentation and Control (I ampersand C)

International Nuclear Information System (INIS)

Dupuis, A.

1995-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the Collection System Instrumentation ampersand Control System for Project C-018H performs according to design. Specifically, this ATP is designed to verify the following overall system requirements: The input and outputs properly connected to the LCU terminal strips. The control system software conforms to the configuration specified by the logic diagrams, piping and instrumentation diagrams (P ampersand ID), and the LERF operating philosophy. Testing will be performed using actual signals. If actual signals are not available, then simulated signals will be used to complete the tests

A field study of the uptake of 35S and 14C into crops characteristic of the UK diet

International Nuclear Information System (INIS)

Kluczewski, S.M.; Bell, J.N.B.; Nair, S.

1986-02-01

The uptake of 35 S and 14 C into crops characteristic of the UK diet was studied. Four common types of green vegetable, six common types of root vegetable and perennial ryegrass were grown in a garden plot in the environs of Hinkley Point Nuclear Power Station and the 35 S and 14 C contents of the crops were measured. Also measured were the corresponding air concentrations over the plot averaged over a range of time periods between sowing and harvesting. The results were analysed in terms of air to crop transfer factors for 35 S and 14 C and the implications of these for dose calculations were assessed for both collective dose and for a hypothetical critical group consuming a range of foods produced in situ. (author)

Growth and characterization of low composition Ge, x in epi-Si1‑x Gex (x  ⩽  10%) active layer for fabrication of hydrogenated bottom solar cell

Science.gov (United States)

Ajmal Khan, M.; Sato, R.; Sawano, K.; Sichanugrist, P.; Lukianov, A.; Ishikawa, Y.

2018-05-01

Semiconducting epi-Si1‑x Ge x alloys have promising features as solar cell materials and may be equally important for some other semiconductor device applications. Variation of the germanium compositional, x in epi-Si1‑x Ge x , makes it possible to control the bandgap between 1.12 eV and 0.68 eV for application in bottom solar cells. A low proportion of Ge in SiGe alloy can be used for photovoltaic application in a bottom cell to complete the four-terminal tandem structure with wide bandgap materials. In this research, we aimed to use a low proportion of Ge—about 10%—in strained or relaxed c-Si1‑x Ge x /c-Si heterojunctions (HETs), with or without insertion of a Si buffer layer grown by molecular beam epitaxy, to investigate the influence of the relaxed or strained SiGe active layer on the performance of HET solar cells grown using the plasma enhanced chemical vapor deposition system. Thanks to the c-Si buffer layer at the hetero-interface, the efficiency of these SiGe based HET solar cells was improved from 2.3% to 3.5% (fully strained and with buffer layer). The Jsc was improved, from 8 mA cm‑2 to 15.46 mA cm‑2, which might be supported by strained c-Si buffer layer at the hetero-interface, by improving the crystalline quality.

Enhanced Electrical Activation in In-Implanted Si0.35Ge0.65 by C Co-Doping

International Nuclear Information System (INIS)

Feng, Ruixing; Kremer, Felipe; Sprouster, David J.; Mirzaei, Sahar; Decoster, Stefan

2016-01-01

In this report, we have achieved a significant increase in the electrically active dopant fraction in Indium (In)-implanted Si 0.35 Ge 0.65 , by co-doping with the isovalent element Carbon (C). Electrical measurements have been correlated with X-ray absorption spectroscopy to determine the electrical properties and the In atom lattice location. With C+In co-doping, the solid solubility of In in Si 0.35 Ge 0.65 was at least tripled from between 0.02 and 0.06 at% to between 0.2 and 0.6 at% as a result of C–In pair formation, which suppressed In metal precipitation. A dramatic improvement of electrical properties was thus attained in the co-doped samples.

Explicit analytical modeling of the low frequency a-Si:H/c-Si heterojunction capacitance: Analysis and application to silicon heterojunction solar cells

Energy Technology Data Exchange (ETDEWEB)

Maslova, O. [Keldysh Institute of Applied Mathematics, Russian Academy of Sciences, Miusskaya sq., 4, Moscow 125047 (Russian Federation); GeePs (Group of electrical engineering of Paris), CNRS UMR 8507, CentraleSupélec, Univ Paris-Sud, Sorbonne Universités-UPMC Univ Paris 06, 11 rue Joliot-Curie, Plateau de Moulon, F-91192 Gif-sur-Yvette Cedex (France); Brézard-Oudot, A.; Gueunier-Farret, M.-E.; Alvarez, J.; Kleider, J.-P. [GeePs (Group of electrical engineering of Paris), CNRS UMR 8507, CentraleSupélec, Univ Paris-Sud, Sorbonne Universités-UPMC Univ Paris 06, 11 rue Joliot-Curie, Plateau de Moulon, F-91192 Gif-sur-Yvette Cedex (France)

2015-09-21

We develop a fully analytical model in order to describe the temperature dependence of the low frequency capacitance of heterojunctions between hydrogenated amorphous silicon (a-Si:H) and crystalline silicon (c-Si). We demonstrate that the slope of the capacitance-temperature (C-T) curve is strongly enhanced if the c-Si surface is under strong inversion conditions compared to the usually assumed depletion layer capacitance. We have extended our analytical model to integrate a very thin undoped (i) a-Si:H layer at the interface and the finite thickness of the doped a-Si:H layer that are used in high efficiency solar cells for the passivation of interface defects and to limit short circuit current losses. Finally, using our calculations, we analyze experimental data on high efficiency silicon heterojunction solar cells. The transition from the strong inversion limited behavior to the depletion layer behavior is discussed in terms of band offsets, density of states in a-Si:H, and work function of the indium tin oxide (ITO) front electrode. In particular, it is evidenced that strong inversion conditions prevail at the c-Si surface at high temperatures down to 250 K, which can only be reproduced if the ITO work function is larger than 4.7 eV.

Energy-Efficient Power Allocation of Cognitive Radio Systems without CSI at the Transmitter

KAUST Repository

Sboui, Lokman

2015-01-07

Two major issues are facing today’s wireless communications evolution: -Spectrum scarcity: Need for more bandwidth. As a solution, the Cognitive Radio (CR) paradigm, where secondary users (unlicensed) share the spectrum with licensed users, was introduced. -Energy consumption and CO2 emission: The ICT produce 2% of global CO2 emission (equivalent to the aviation industry emission). The cellular networks produces 0.2%. As solution energy efficient systems should be designed rather than traditional spectral efficient systems. In this work, we aim to determine the optimal energy efficient power allocation of CR when the channel state information at the transmitter CSI-T is not available.

Energy-Efficient Power Allocation of Cognitive Radio Systems without CSI at the Transmitter

KAUST Repository

Sboui, Lokman; Rezki, Zouheir; Alouini, Mohamed-Slim

2015-01-01

Two major issues are facing today’s wireless communications evolution: -Spectrum scarcity: Need for more bandwidth. As a solution, the Cognitive Radio (CR) paradigm, where secondary users (unlicensed) share the spectrum with licensed users, was introduced. -Energy consumption and CO2 emission: The ICT produce 2% of global CO2 emission (equivalent to the aviation industry emission). The cellular networks produces 0.2%. As solution energy efficient systems should be designed rather than traditional spectral efficient systems. In this work, we aim to determine the optimal energy efficient power allocation of CR when the channel state information at the transmitter CSI-T is not available.

Transfer and breakup reactions in 16O + CsI at 16.4 MeV/n

Directory of Open Access Journals (Sweden)

M.J. Murphy

1983-01-01

Full Text Available A streamer-chamber particle-telescope system has been used to observe ejectile charge, energy, and associated charged particle multiplicity in the reaction of 16O + CsI at 16.4 MeV/n. The measurement provides relative probabilities for transfer and projectile breakup as a function of ejectile charge, and spectra for the heavy ejectiles from transfer and breakup events. The results show that the interaction energy of 16.4 MeV/n is near the threshold for breakup reactions in heavy-ion collisions.

A1c Gear: Laboratory quality HbA1c measurement at the point of care.

Science.gov (United States)

Ejilemele, Adetoun; Unabia, Jamie; Ju, Hyunsu; Petersen, John R

2015-05-20

HbA1c is an important part of assessing the diabetic control and since the use of point-of-care devices for monitoring HbA1c is increasing, it is important to determine how these devices compare to the central laboratory. One hundred and twenty patient samples were analyzed on the Bio-Rad Variant™II and one POC analyzer (Sakae A1c Gear). Three patient sample pools containing ~5%, ~7%, and ~10% HbA1c levels were run over 20 days. Three reagent lots and three instruments were evaluated for the A1c Gear. The 120 patient samples showed strong correlation (R(2)>0.989) when compared to the Variant™II with means=8.06% and 7.81%, for Variant IIand A1c Gear, respectively. Changing reagent lots or instruments had no impact for the A1c Gear. The ~5%, ~7%, and ~10% pools within-run and between-run imprecision was between 0.87-1.33% and 1.03-1.32%, and 1.41-2.35% and 1.24-1.89% with total imprecision of 1.67-2.35% and 1.61-2.31% for the A1c Gear and Variant II, respectively. The A1c Gear showed a small negative bias (0.25% HbA1c) across HbA1c measurement ranges of Gear meets the criteria of total CV Gear can give results as precise as the laboratory at the POC. Copyright © 2015. Published by Elsevier B.V.

Secondary emission coefficient dependence on the angle of incidence of primary electrons on CsI and LiF layers. [0. 9 to 3 keV, mechanism

Energy Technology Data Exchange (ETDEWEB)

Shabel' nikova, A E; Yasnopol' skii, N L

1976-08-01

The angular dependence was studied of the secondary emission coefficient sigma for CsI and LiF dielectrics which have large sigma in conditions of normal incidence of primary electrons. Measurements were taken down to the angle of 85 deg for energies of primary electrons between 0.9 and 3 keV. In the whole range of angles a nonmonotonic angular dependence sigma is observed. The dependence shows itself particularly clearly for CsI at large energies of primary electrons. Such a behaviour is due to the decrease in the depth of yield of inelastically reflected electrons and to the increase in the inelastic reflection coefficient of the substance.

On mass in 4π solid angle around song CsI scintillator aboard coronas-I satellite

International Nuclear Information System (INIS)

Bucik, R.; Kudela, K.

2003-01-01

The complex geometric setup around the SONG CsI scintillator aboard the CORONAS-1 satellite has been modelled, to evaluate the mass thickness passed through by the cosmic ray particle striking the detector. The analytic functional form giving the amount of matter traversed in absorbers for an arbitrary incident directions is present. The population mean and variance of the mass thickness are estimated by random sampling of the uniformly distributed particle trajectories in the several solid angles (Authors)

Measurement of exclusive hypercharge-exchange reactions at 35 to 140 GeV/c

International Nuclear Information System (INIS)

Arenton, M. W.; Ayres, D.S.; Cohen, D.

1978-07-01

Data on the reactions π + p → K + Σ + and π + p → K + Y* + were obtained using the Fermilab Single Arm Spectrometer Facility at incident π + momenta of 35, 70, and 140 GeV/c for momentum transfers vertical bar t vertical bar less than or approximately equal to 1 GeV 2 . The line-reversed reactions K - p → π - Σ + and K - p → π - Y* + were also studied at 70 GeV/c with the same apparatus in order to test exchange degeneracy of the K*(890) and K**(1420) trajectories. Preliminary results on the first set of reactions at 70 GeV/c are presented and found to be in qualitative agreement with the model of Navelet and Stevens

Gender differences in Croatian consumer decision-making styles

Directory of Open Access Journals (Sweden)

Ivan-Damir Anić

2010-06-01

Full Text Available This paper tests the applicability of the CSI instrument to measuring consumer decision-making styles in the Croatian environment. The analysis assesses the validity and the reliability of CSI scales and examines gender differences in consumer-decision making styles. Research results point to the existence of eight consumer characteristics and thus validate the applicability of CSI instrument in the Croatian environment. Our findings further indicate that there were gender differences on five factors of consumer-decision making styles (perfectionist, novelty-fashion consciousness, recreational-hedonistic consumer, impulsiveness, habitual shopping behavioral. No significant differences in consumer decision styles between men and women were found with regard to three factors (brand consciousness, price consciousness and confused by overabundant choice. The CSI measurement system may help practitioners to gain a better understanding of how to position their products and services more effectively.

The effect of γ-ray irradiation on the adsorption properties and chemical stability of AMP/SiO2 towards Cs(I) in HNO3 solution

International Nuclear Information System (INIS)

Xiaoxia Zhang; Yan Wu; Yuezhou Wei; Guangxi University, Nanning

2016-01-01

Silica based ammonium molybdophosphate (AMP/SiO 2 ) adsorbent was used to remove Cs(I) from HNO 3 solution. The adsorbent with different absorbed dose (0-300 kGy) was characteristed by X-ray power diffraction. The adsorption data against different γ-ray absorbed doses were analyzed by the Langmuir isotherm. The adsorption capacity decreased slightly from 23.22 to 22.37 mg/g with the increase of the absorbed dose. The breakthrough properties of Cs(I) were conducted using column packed with AMP/SiO 2 before and after irradiation. The chemical stability of AMP/SiO 2 at 300 kGy absorbed dose in 3 mol/L (M) HNO 3 was excellent. (author)

Profili di salute soggettivi e oggettivi: una combinazione vincente

Directory of Open Access Journals (Sweden)

C. Quercioli

2003-05-01

Full Text Available

Introduzione: nella valutazione prospettica dell’impegno assistenziale richiesto o retrospettiva del risultato di salute ottenuto, entrambi collegabili a meccanismi retributivi, diventa sempre più importante usare sintetici descrittori di severità/complessità/outcome. In quest’ottica abbiamo studiato con strumenti oggettivi (Charlson Index Score-CSI e soggettivi (SF36 lo stato di salute di pazienti non ospedalizzati. Obiettivo: confrontare e correlare i livelli di salute registrati con i due strumenti.

Materiali e Metodi: il CSI è un indice che considera numero e severità delle copatologie. Il questionario SF36 studia lo stato di salute percepito attraverso 8 domini. Sono stati studiati 137 pazienti di un Medico di Medicina Generale, che ha fornito età, sesso, livello di istruzione e stato civile dei pazienti. È stato creato un modello di regressione in cui il punteggio del CSI costituiva la variabile dipendente e le quattro scale dell’SF36 che sono risultate correlate con il CSI le variabili indipendenti. Risultati: è stata identificata correlazione tra i punteggi del CSI e le scale Salute Generale (SG (Coefficiente di Spearman 0,38 p‹0,001, Attività Fisica (AF (C.S. 0,35 p‹0,001, Ruolo Fisico (RF (C.S. 0,37 p‹0,001, Ruolo Emotivo (RE (C.S. 0,25 p=0,003. Aggiustando il CSI e le suddette 4 scale dell’SF 36 per “sesso”, “livello di istruzione” e “stato civile”, si è trovato che: (i “stato civile” influenza l’associazione tra RF e CSI (crude O.R. 1,71, p‹0,001; O.R. coniugati 1,47 p= 0,025; O.R. non coniugati 3,05 p‹ 0,001 e SG e CSI (crude O.R. 1,76 p‹0,001; O.R. stato civile 1,61 p=0,006; (ii “livello di istruzione” influenza l’associazione tra AF e CSI (crude O.R. 1,88 p‹0,001; O.R. livello di istruzione 1,76 p=0,001 e SG e CSI (crude O.R. 1,76 p‹0,001; O.R. elevata istruzione 1,22 p=0,33; O.R. scarsa istruzione 2,69 p‹0,001.

Instrument Control (iC) – An Open-Source Software to Automate Test Equipment

Science.gov (United States)

Pernstich, K. P.

2012-01-01

It has become common practice to automate data acquisition from programmable instrumentation, and a range of different software solutions fulfill this task. Many routine measurements require sequential processing of certain tasks, for instance to adjust the temperature of a sample stage, take a measurement, and repeat that cycle for other temperatures. This paper introduces an open-source Java program that processes a series of text-based commands that define the measurement sequence. These commands are in an intuitive format which provides great flexibility and allows quick and easy adaptation to various measurement needs. For each of these commands, the iC-framework calls a corresponding Java method that addresses the specified instrument to perform the desired task. The functionality of iC can be extended with minimal programming effort in Java or Python, and new measurement equipment can be addressed by defining new commands in a text file without any programming. PMID:26900522

Geotechnical instrumentation requirements for at-depth testing and repository monitoring in tuff

International Nuclear Information System (INIS)

Zimmerman, R.M.

1982-01-01

Minimum required geotechnical measurements for confirmation of repository performance include thermal and thermomechanical responses; changes in stress, strain, and displacements; and pore pressure and groundwater flow characteristics. Conditions expected in tuff are: maximum rock temperatures of less than 250 0 C, stresses less than 100 MPa, strains between +-0.01 mm/mm, and pore pressures less than 35 KPa in the unsaturated zone where hydraulic head is not the primary contributor. The paper describes instrumentation needed to make the desired measurements. In general, the instrumentation and data system are required to be stable and reliable for tens of years. Designs must consider requirements for temperature stability, temperature expansion compensation, moisture resistance, and long-term durability in mining-type environments. Severe requirements such as these suggest consideration of techniques for in-situ replacement of instrumentation. State-of-the-art instrumentation is briefly described along with a discussion of needs for refinement, replacement/recalibration and instrumentation development

A strictly monofunctional bacterial hydroxymethylpyrimidine phosphate kinase precludes damaging errors in thiamin biosynthesis.

Science.gov (United States)

Thamm, Antje M; Li, Gengnan; Taja-Moreno, Marlene; Gerdes, Svetlana Y; de Crécy-Lagard, Valérie; Bruner, Steven D; Hanson, Andrew D

2017-07-20

The canonical kinase (ThiD) that converts the thiamin biosynthesis intermediate hydroxymethylpyrimidine (HMP) monophosphate to the diphosphate can also very efficiently convert free HMP to the monophosphate in prokaryotes, plants, and fungi. This HMP kinase activity enables salvage of HMP, but it is not substrate-specific and so allows toxic HMP analogs and damage products to infiltrate the thiamin biosynthesis pathway. Comparative analysis of bacterial genomes uncovered a gene, thiD2 , that is often fused to the thiamin synthesis gene thiE and could potentially encode a replacement for ThiD. Standalone ThiD2 proteins and ThiD2 fusion domains are small (~130-residues) and do not belong to any previously known protein family. Genetic and biochemical analyses showed that representative standalone and fused ThiD2 proteins catalyze phosphorylation of HMP monophosphate, but not of HMP or its toxic analogs and damage products such as bacimethrin and 5-(hydroxymethyl)-2-methylpyrimidin-4-ol. As strictly monofunctional HMP monophosphate kinases, ThiD2 proteins eliminate a potentially fatal vulnerability of canonical ThiD, at the cost of the ability to reclaim HMP formed by thiamin turnover. ©2017 The Author(s).

Validation of the Artsana CSI 610 automated blood pressure monitor in adults according to the International Protocol of the European Society of Hypertension.

Science.gov (United States)

Pini, Claudio; Pastori, Marco; Baccheschi, Jordan; Omboni, Stefano; Parati, Gianfranco

2007-06-01

There is evidence that blood pressure measurement outside the doctor's office can provide valuable information for the diagnostic evaluation of hypertensive patients and for monitoring their response to treatment. Home blood pressure monitoring devices have a major role in this setting, provided that their accuracy in measuring blood pressure is demonstrated by validation studies. This study aimed at verifying whether the automatic electronic oscillometric blood pressure measuring device Artsana CSI 610 complied with the standard of accuracy indicated by the ESH International Protocol. Sequential measurements of systolic and diastolic blood pressure were obtained in 33 participants using the mercury sphygmomanometer (two observers) and the test device (one supervisor). A standard adult cuff was always employed during the study. According to the ESH validation protocol, 99 couples of test device and reference blood pressure measurements were obtained during the two phases of the study (three pairs for each of the 33 participants). The Artsana CSI 610 device successfully passed phase 1 of study validation with the number of absolute differences between test and reference device never validation study with a mean (+/-SD) device-observer difference of -1.4+/-4.8 mmHg for systolic and -0.9+/-3.5 mmHg for diastolic blood pressure. According to the results of the validation study on the basis of the ESH International Protocol, the Artsana CSI 610 can be recommended for clinical use in adults.

CSI Index Of Customer’s Satisfaction Applied In The Area Of Public Transport

Directory of Open Access Journals (Sweden)

Poliaková Adela

2015-06-01

Full Text Available In Western countries, the new visions are applied in quality control for an integrated public transport system. Public transport puts the customer at the centre of our decision making in achieving customer satisfaction with provided service. Sustainable surveys are kept among customers. A lot of companies are collecting huge databases containing over 30,000 voices of customers, which demonstrates the current satisfaction levels across the public transport service. Customer satisfaction with a provided service is a difficult task. In this service, the quality criteria are not clearly defined, and it is therefore difficult to define customer satisfaction. The paper introduces a possibility of CSI index application in conditions of the Slovak Republic transport area.

MPO cDNA clone identifies an RFLP with PstI

Energy Technology Data Exchange (ETDEWEB)

Miki, T; Weil, S C; Rosner, G L; Reid, M S; Kidd, K K

1988-02-25

A myeloperoxidase (MPO) cDNA clone (pHMP7: 270 base pair insert in the vector pGEM-1reverse arrow was isolated from a library created from human promyelocytic (HL-60) cell mRNA. PstI (CTGCA/G) (New England Biolabs) identifies a simple two-allele polymorphism with bands at either 2.2 kb (Al) or 2.0 kb (A2). There are three constant bands at 2.8 kb, 0.95 kb and 0.6 kb. Preliminary family data show evidence of linkage to several markers in proximal 17q, with MPO closest to the Growth Hormone cluster at 17q22-q24. Autosomal condominant segregation was observed in four large reference pedigrees with several informative matings.

Dopamine improves hypothermic machine preservation of the liver.

Science.gov (United States)

Minor, Thomas; Lüer, Bastian; Efferz, Patrik

2011-10-01

Hypothermic machine preservation (HMP) is currently reconsidered as alternative to standard cold storage of organs from non-heart-beating donors. The present study was aimed at investigating the possible synergistic effect of HMP and the addition of dopamine to the circulating perfusate during preservation. Cardiac arrest was induced in male Wistar rats (250-300 g) by phrenotomy. Thirty minutes later livers were flushed via the portal vein and subjected to 20 h of HMP at 5ml/min at 4°C. During HMP the preservation solution was equilibrated with 100% oxygen and dopamine was added at 0, 10, 50 or 100 μM (D0, D10, D50, D100; n=6 resp.). Graft viability was assessed thereafter upon warm reperfusion in vitro for 2h. During HMP, D50 and D100 significantly reduced hepatic release of ALT to about 50%. No influence of dopamine was found on vascular resistance, oxygen uptake or lactate production at any concentration. D50 significantly reduced enzyme release during reperfusion (∼50%), enhanced bile flow and oxygen consumption. D10 was less effective while D100 even rose enzyme release compared with D0. Enhanced oxygen free radical mediated lipid peroxidation (LPO), found in the tissue of D0 livers was significantly reduced by D50; D50 significantly abrogated molecular upregulation of vWillebrand factor upon reperfusion suggesting vascular protection of the endothelial cell. Efficiency of HMP might be increased by stimulating livers with dopamine during ex vivo preservation, limiting vascular side effects and improving functional recovery upon early reperfusion. Copyright © 2011 Elsevier Inc. All rights reserved.

C-Si solar cell modules

International Nuclear Information System (INIS)

Tomita, Takashi

2005-01-01

In order to meet the rapidly growing demand for solar power photovoltaic systems which is based on public consciousness of global environmental issues, SHARP has increased the production of solar cells and modules over 10-fold in the last 5 years. Silicon-based technologies are expected to be dominant in the coming decade. In the course of an increase of the annual production scale to 1000 MW, the efficiency of modules will be improved and the thickness of wafers will be decreased and all this will lead to a drastic price reduction of PV systems. (Author)

The upgraded control and instrumentation system of C9 irradiation device

International Nuclear Information System (INIS)

Pulpa, A.; Parvu, C.; Valeca, S. C.; Ancuta, M.; Ana, E.

2016-01-01

C9 Capsule is an irradiation device of TRIGA SSR, which was designed for nuclear fuel cycling testing. It simulates the load follow-up by the power reactor, i.e. CANDU 700MW operating with variable load. The irradiation tests in the power cycling conditions were conceived for complete characterization of the fuel behaviour. The irradiation conditions are similar to those found in nuclear power plant when it is operated in load following mode. The power cycling tests are performed by using an under flux moving system. The paper presents the upgraded control and instrumentation system of the ''9C irradiation device, designed and manufactured in order to enhance the performance of this system for better surveillance and processing of the acquired experimental data. (authors)

Esters with imidazo [1,5-c] quinazoline-3,5-dione ring spectral characterization and quantum-mechanical modeling.

Science.gov (United States)

Hęclik, K; Szyszkowska, A; Trzybiński, D; Woźniak, K; Klasek, A; Zarzyka, I

2017-04-01

1-phenyl-2H,6H-imidazo[1,5-c]quinazoline-3,5-dione reacts with ethyl bromoacetate under mild conditions to give 2-(ethoxycarbonylmethyl)-1-phenyl-6H-imidazo[1,5-c]quinazoline-3,5-dione (MEPIQ) and next 2,6-bis(ethoxycarbonylmethyl)-1-phenylimidazo[1,5-c]quinazoline-3,5-dione (BEPIQ). The products were isolated at high yield and identified on the basis of IR, 1 H- and 13 C-NMR, UV spectroscopy, and X-ray crystallography. Diester (BEPIQ) can be presented by 16 possible pair of enantiomers. Only one pair of them is the most stable and crystallizes which is shown crystallographic research. Based on quantum-mechanical modeling, with the use of DFT method, which conformers of mono- and diester and why they were formed was explained. It was calculated that 99.93% of the monoester (MEPIQ) is formed at position No. 2 and one pair of the monoester conformers, from six possible, has the largest share (51.63%). These results afforded to limit the number of diester conformers to eight. Unfortunately, the quantum-mechanical calculations performed that their shares are similar. Further quantum-mechanical modeling showed that conformers are able to undergo mutual transformations. As a result only one pair of diester conformers forms crystals. These conformers have substituents in trans position and these substituents are located parallel to imidazoquinazoline ring. This allows for the denser packing of the molecules in the unit cell.

Molecular Structures, Vibrational Spectroscopy, and Normal-Mode Analysis of M(2)(C&tbd1;CR)(4)(PMe(3))(4) Dimetallatetraynes. Observation of Strongly Mixed Metal-Metal and Metal-Ligand Vibrational Modes.

Science.gov (United States)

John, Kevin D.; Miskowski, Vincent M.; Vance, Michael A.; Dallinger, Richard F.; Wang, Louis C.; Geib, Steven J.; Hopkins, Michael D.

1998-12-28

The nature of the skeletal vibrational modes of complexes of the type M(2)(C&tbd1;CR)(4)(PMe(3))(4) (M = Mo, W; R = H, Me, Bu(t)(), SiMe(3)) has been deduced. Metrical data from X-ray crystallographic studies of Mo(2)(C&tbd1;CR)(4)(PMe(3))(4) (R = Me, Bu(t)(), SiMe(3)) and W(2)(C&tbd1;CMe)(4)(PMe(3))(4) reveal that the core bond distances and angles are within normal ranges and do not differ in a statistically significant way as a function of the alkynyl substituent, indicating that their associated force constants should be similarly invariant among these compounds. The crystal structures of Mo(2)(C&tbd1;CSiMe(3))(4)(PMe(3))(4) and Mo(2)(C&tbd1;CBu(t)())(4)(PMe(3))(4) are complicated by 3-fold disorder of the Mo(2) unit within apparently ordered ligand arrays. Resonance-Raman spectra ((1)(delta-->delta) excitation, THF solution) of Mo(2)(C&tbd1;CSiMe(3))(4)(PMe(3))(4) and its isotopomers (PMe(3)-d(9), C&tbd1;CSiMe(3)-d(9), (13)C&tbd1;(13)CSiMe(3)) exhibit resonance-enhanced bands due to a(1)-symmetry fundamentals (nu(a) = 362, nu(b) = 397, nu(c) = 254 cm(-)(1) for the natural-abundance complex) and their overtones and combinations. The frequencies and relative intensities of the fundamentals are highly sensitive to isotopic substitution of the C&tbd1;CSiMe(3) ligands, but are insensitive to deuteration of the PMe(3) ligands. Nonresonance-Raman spectra (FT-Raman, 1064 nm excitation, crystalline samples) for the Mo(2)(C&tbd1;CSiMe(3))(4)(PMe(3))(4) compounds and for Mo(2)(C&tbd1;CR)(4)(PMe(3))(4) (R = H, D, Me, Bu(t)(), SiMe(3)) and W(2)(C&tbd1;CMe)(4)(PMe(3))(4) exhibit nu(a), nu(b), and nu(c) and numerous bands due to alkynyl- and phosphine-localized modes, the latter of which are assigned by comparisons to FT-Raman spectra of Mo(2)X(4)L(4) (X = Cl, Br, I; L = PMe(3), PMe(3)-d(9))(4) and Mo(2)Cl(4)(AsMe(3))(4). Valence force-field normal-coordinate calculations on the model compound Mo(2)(C&tbd1;CH)(4)P(4), using core force constants transferred from a calculation

24 CFR 27.35 - Foreclosure costs.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Foreclosure costs. 27.35 Section 27.35 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development... Mortgages § 27.35 Foreclosure costs. Pursuant to section 369C(5) of the Act (12 U.S.C. 3711(5)), a...

Hypothyroidism in children with medulloblastoma: a comparison of 3600 and 2340 cGy craniospinal radiotherapy

International Nuclear Information System (INIS)

Paulino, Arnold C.

2002-01-01

Purpose: To determine if low-dose craniospinal irradiation (2340 cGy) with chemotherapy is associated with a lower incidence of hypothyroidism compared to standard dose (3600 cGy) with or without chemotherapy in children with medulloblastoma. Patients and Methods: Between 1980 and 1999, 32 patients ≤20 years old survived after craniospinal irradiation with or without chemotherapy. Twenty patients received 3600 cGy craniospinal irradiation (CSI), whereas 12 had 2340 cGy CSI; all patients received a posterior fossa boost to a total dose 5040-5580 cGy. The median ages at the time of CSI for those receiving 2340 cGy and 3600 cGy were 7.2 and 10.2 years, respectively. Chemotherapy (CT) was employed in 22 children. All children who received 2340 cGy had CT consisting of vincristine, CCNU, and either cisplatin or cyclophosphamide. Ten of 20 (50%) patients receiving 3600 cGy had CT; the most common regimen was vincristine, CCNU, and prednisone. Serum-free thyroxine and thyroid-stimulating hormone concentrations were measured in all children at variable times after radiotherapy. Thyroid-stimulating hormone responses to i.v. thyrotrophin-releasing hormone were assessed in those suspected of having central hypothyroidism. Median follow-up for children receiving 2340 cGy was 5 years (range: 2-11.2 years), whereas for those receiving 3600 cGy, follow-up was 12.5 years (range: 2.4-20 years). Results: Eighteen patients (56%) developed hypothyroidism at a median time after radiotherapy of 41 months (range: 10 months to 18 years). Primary hypothyroidism was more common than central hypothyroidism (38% and 19%). All 7 children 10 years had hypothyroidism (p<0.001). Hypothyroidism was documented in 10 of 12 (83%) who had 2340 cGy + CT, 6 of 10 (60%) who had 3600 cGy + CT, and 2 of 10 (20%) who had 3600 cGy without CT (p<0.025). Conclusions: Current treatment regimens consisting of chemotherapy and 2340 cGy craniospinal irradiation followed by a posterior fossa boost for

Study of the {pi}{sup +} -proton interaction at 3,5 GeV / c; Une etude de l'interaction {pi}{sup +} proton a 3,5 GeV / c

Energy Technology Data Exchange (ETDEWEB)

Duong, N H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-01-01

The {pi}{sup +} proton interaction leading to two charged outgoing particles have been studied at the incident momentum of 3.2 and 3.5 GeV/c. The picture were obtained from an exposure of the Brookhaven Notional Laboratory 20 - inch bubble chamber. For the two energies, we have identified: 1741 events of the reaction {pi}{sup +} + p {yields} {pi}{sup +} + p +{pi}{sup 0}, 1100 events of the reaction {pi}{sup +} + p {yields} {pi}{sup +} + {pi}{sup +} + n and 4079 events of the reaction {pi}{sup +} + p {yields} {pi}{sup +} + p. We present here a study of the exchange mechanism in the N*{sub 33} production. The resonances Ni*{sub 1/2}(1688), {rho}, {eta}, {omega} and A1, A2 are observed and discussed. Other results, the elastic interaction and various cross sections are also presented. (author) [French] L'interaction {pi}{sup +} proton donnant deux particules chargees dans l'etat final a ete etudiee aux impulsions incidentes de 3,2 et 3,5 GeV/c. L'experience a ete effectuee a l'aide de la chambre a bulles de 50 cm du Laboratoire National de Brookhaven. Au total, nous avons identifie: 1741 evenements de la reaction {pi}{sup +} + p {yields} {pi}{sup +} + p +{pi}{sup 0}, 1100 evenements de la reaction {pi}{sup +} + p {yields} {pi}{sup +} + {pi}{sup +} + n et 4079 evenements de la reaction {pi}{sup +} + p {yields} {pi}{sup +} + p. Nous presentons ici une etude du mecanisme d'echange dans la production du N*{sub 33}. L'observation des resonances N*{sub 1/2}(1688), {rho}, {eta}, {omega} et A1, A2 est rapportee, suivie d'une analyse phenomenologique. D'autres resultats concernant l'interaction elastique et les diverses sections efficaces sont presentes. (auteur)

Comparison of patient-reported late treatment toxicity (LENT-SOMA) with quality of life (EORTC QLQ-C30 and QLQ-H and N35) assessment after head and neck radiotherapy

International Nuclear Information System (INIS)

Ho, Kean Fatt; Farnell, Damien J.J.; Routledge, Jacqueline A.; Burns, Meriel P.; Sykes, Andrew J.; Slevin, Nick J.; Davidson, Susan E.

2010-01-01

Purpose: The patient's role in toxicity reporting is increasingly acknowledged but requires the adaptation and validation of toxicity reporting instruments for patient use as most toxicity scales are designed for physician use. Recording of radiotherapy related late toxicity is important and needs to be improved. A patient-scored symptom questionnaire of late treatment effects using LENT-SOMA was compared with a recognised quality of life tool (EORTC QLQ-C30/H and N35). Materials/methods: LENT-SOMA and EORTC QLQ-C30 patient questionnaires were prospectively completed by 220 head and neck cancer patients over 3 years and 72 completed EORTC QLQ-H and N35 questionnaires at 2 years post-radiotherapy. Results: Endpoints common to both questionnaires (pain, swallowing, dental pain, dry mouth, opening mouth, analgesics) were matched. Spearman rank correlation coefficients with ρ > 0.6 (P < 0.001) were obtained for all 'matched' scales except for analgesics scale, ρ = 0.267 (P < 0.05). There was good agreement between LENT-SOMA and EORTC QLQ-H and N35 except for analgesic endpoints. Global quality of life scores correlated negatively with average LENT-SOMA scores (P < 0.001). Significant differences in average LENT-SOMA scores between treatment modalities were found. The LENT-SOMA questionnaire has demonstrated a high Cronbach's α value (0.786) indicating good reliability. Conclusions: LENT-SOMA patient questionnaire results agreed well with those from the EORTC QLQ-H and N35 questionnaire for toxicity items where they could be compared explicitly, particularly for subjective endpoints. Patient-reported late toxicity had a negative impact on quality of life. The LENT-SOMA patient questionnaire is both reliable and sensitive to differences between patients treated with different modalities. A patient-based questionnaire is an important contributor to capturing late radiotherapy effects.

Minimax robust relay selection based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish

2014-02-01

Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot-based transmission or distributed space-time (ST) code implementation. Dynamically selecting a single best relay out of multiple relays and then using it alone for cooperative transmission alleviates the need for this strong coordination while still reaping the benefits of increased diversity and coverage. In this paper, we consider the design of relay selection (RS) under an imperfect knowledge of long-term channel state information (CSI) at the relay nodes, and we pursue minimax optimization to arrive at a robust RS approach that promises the best guarantee on the worst-case end-to-end signal-to-noise ratio (SNR). We provide some intuitive examples and extensive simulation results, not only in terms of worst-case SNR performance but also in terms of average bit-error-rate (BER) performance, to demonstrate the benefits of the proposed minimax robust RS scheme. © 2013 IEEE.

A high speed digitizing photomultiplier tube base for the KTeV CsI calorimeter

International Nuclear Information System (INIS)

Whitmore, J.

1994-11-01

A circuit has been designed to digitize PMT signals over an 18-bit dynamic range with 8-bits of resolution. The crucial element of the circuit is the custom charge integrating and encoding (QIE) ASIC. This chip is designed to operate at rates up to 53 MHz, and, in conjunction with an 8-bit FADC, generates 12-bit floating point output. Bench tests of a 17-bit version of the digital base demonstrated excellent noise performance, linearity and pedestal and gain stability. Twenty-five channels of digitizing PMT bases have been built and used for readout of a CsI array in a test beam at CERN. Performance of these devices in a beam environment is discussed

Law & Order, CSI, and NCIS: The Association Between Exposure to Crime Drama Franchises, Rape Myth Acceptance, and Sexual Consent Negotiation Among College Students.

Science.gov (United States)

Hust, Stacey J T; Marett, Emily Garrigues; Lei, Ming; Ren, Chunbo; Ran, Weina

2015-01-01

Previous research has identified that exposure to the crime drama genre lowers rape myth acceptance and increases sexual assault prevention behaviors such as bystander intervention. However, recent content analyses have revealed marked differences in the portrayal of sexual violence within the top three crime drama franchises. Using a survey of 313 college freshmen, this study explores the influence of exposure to the three most popular crime drama franchises: Law & Order, CSI, and NCIS. Findings indicate that exposure to the Law & Order franchise is associated with decreased rape myth acceptance and increased intentions to adhere to expressions of sexual consent and refuse unwanted sexual activity; whereas exposure to the CSI franchise is associated with decreased intentions to seek consent and decreased intentions to adhere to expressions of sexual consent. Exposure to the NCIS franchise was associated with decreased intentions to refuse unwanted sexual activity. These results indicate that exposure to the specific content of each crime drama franchise may have differential results on sexual consent negotiation behaviors.

Adsorption of Cs(I), Sr(II), Eu(III), Co(II) and Cd(II) by Al2O3

International Nuclear Information System (INIS)

Shiao, S.Y.; Egozy, Y.; Meyer, R.E.

1981-01-01

Adsorption of Cs(I), Sr(II), Eu(III), Co(II) and Cd(II) by Al 2 O 3 was carried out over a wide range of NaCl concentration and solution pH. In the medium pH region (pH 5 to 9), adsorption depends strongly on pH and less on salt concentration. However, in the high pH region (pH above 9), the salt dependence of the distribution coefficient becomes important. (author)

Virucidal efficacy of peracetic acid for instrument disinfection.

Science.gov (United States)

Becker, Britta; Brill, Florian H H; Todt, Daniel; Steinmann, Eike; Lenz, Johannes; Paulmann, Dajana; Bischoff, Birte; Steinmann, Jochen

2017-01-01

drying and immerging could be observed. In consequence, a four log reduction of poliovirus titer could not be achieved in the carrier test. In summary, 1500 ppm PAA at 35 °C was necessary for a virucidal action in the quantitative suspension test. After passing the requirements of the suspension test, additional examinations with adeno- and murine norovirus on glass carriers based on prEN 17111:2017 will not additionally contribute to the final claim of an instrument disinfectant for virucidal efficacy. This is due to the great stability of poliovirus in the preceded quantitative suspension test and the fact that poliovirus could not serve as test virus in the following carrier assay.

NanoSIMS isotope studies of rare types of presolar silicon carbide grains from the Murchison meteorite: Implications for supernova models and the role of 14C

Science.gov (United States)

Hoppe, Peter; Pignatari, Marco; Kodolányi, János; Gröner, Elmar; Amari, Sachiko

2018-01-01

We have conducted a NanoSIMS ion imaging survey of about 1800 presolar silicon carbide (SiC) grains from the Murchison meteorite. A total of 21 supernova (SN) X grains, two SN C grains, and two putative nova grains were identified. Six particularly interesting grains, two X and C grains each and the two putative nova grains were subsequently studied in greater detail, namely, for C-, N-, Mg-Al-, Si-, S-, and Ca-Ti-isotopic compositions and for the initial presence of radioactive 26Al (half life 716,000 yr), 32Si (half life 153 yr), and 44Ti (half life 60 yr). Their isotope data along with those of three X grains from the literature were compared with model predictions for 15 M⊙ and 25 M⊙ Type II supernovae (SNe). The best fits were found for 25 M⊙ SN models that consider for the He shell the temperature and density of a 15 M⊙ SN and ingestion of H into the He shell before the explosion. In these models a C- and Si-rich zone forms at the bottom of the He burning zone (C/Si zone). The region above the C/Si zone is termed the O/nova zone and exhibits the isotopic fingerprints of explosive H burning. Satisfactory fits of measured C-, N-, and Si-isotopic compositions and of 26Al/27Al ratios require small-scale mixing of matter originating from a region extending over 0.2 M⊙ for X and C grains and over 0.4 M⊙ for one of the putative nova grains, involving matter from a thin Si-rich layer slightly below the C/Si zone, the C/Si zone, and the O/nova zone. Simultaneous fitting of 14N/15N and 26Al/27Al requires a C-N fractionation of a factor of 50 during SiC condensation. This leads to preferential incorporation of radioactive 14C (half life 5700 yr) over directly produced 14N and can account for the 14N/15N along with 26Al/27Al ratios as observed in the SiC grains. The good fit for one of the putative nova grains along with its high 26Al/27Al points towards a SN origin and supports previous suggestions that some grains classified as nova grains might be from SNe

Measurements of the radiolytic oxidation of aqueous CsI using a sparging apparatus

Energy Technology Data Exchange (ETDEWEB)

Ashmore, C B; Brown, D; Sims, H E [AEA Technology, Harwell (United Kingdom); Gwyther, J R [NE plc Berkeley Technology Centre, Berkeley (United Kingdom)

1996-12-01

Radiolytic oxidation is considered to be the main mechanism for the formation of I{sub 2} from aqueous CsI in containment of a water cooled reactor after a LOCA. Despite the amount of study over the last 60 years on the radiation chemistry of iodine there has been no consistent set of experiments spanning a wide enough range of conditions to verify models with confidence. This paper describes results from a set of experiments carried out in order to remedy this deficiency. In this work the rate of evolution of I{sub 2} from sparged irradiated CsI solution labeled with {sup 131}I was measured on-line over a range of conditions. This work involved the measurement of the effects of pH, temperature, O{sub 2} concentration, I{sup -} concentration, phosphate concentration, dose-rate and impurities on the rate of evolution of I{sub 2}. The range of conditions was chosen in order to span as closely as possible conditions expected in a LOCA but also to help to elucidate some of the mechanisms especially at high pH. pH was found to be a very important factor influencing iodine volatility, over the temperature range studied the extent of oxidation reduced with temperature but this was compensated for by the decrease in partition coefficient. Oxygen concentration was more important in solutions not containing phosphate. The fractional oxidation was not particularly dependent on iodide concentration but G{sub I2} was very dependent on [I{sup -}]. There was no effect of added impurities, Fe, Mn, Mo or organics although in separate work silver was found to have a very important effect. During attempts to interpret the data it was found that it was necessary to include the iodine atom as a volatile species with a partition coefficient of 1.9 taken from thermodynamic data. The modelling work is described in a separate paper. (author) 15 figs., 1 tab., 19 refs.

Studies on a modular high-energy photon spectrometer of pure CsI scintillators

International Nuclear Information System (INIS)

Kopyto, D.

1994-04-01

Aim of the present thesis is the optimization of components for the construction of a high-energy photon spectrometer of pure CsI for the detection of the neutral pseudoscalar mesons π 0 , η, and η' at COSY. These mesons are distinguished by their decay into two γ quanta and can therefore be detected by means of a photon spectrometer. A concept of a 2-arm shower counter of pure CsI is presented. Conclusions on the energy resolution of such a calorimeter shall yield a test module, which is constructed of 5.5 CsI(pure) pyramide trunk, each of which possesses a length of 30 cm and an angular acceptance of 6 .6 . The geometry of the moduls is formed in such a way that its extension to a 2-arm shower counter is possible at any time. Hitherto 14 by teflon foils wrapped up crystals for the test module were tested. Their energy resolution varies at 0.66 MeV between 20 and 25 % FWHM. Furthermore a method was found, which allows to trim the position dependence to the required values. So for the position dependence of a crystal even a value of 1.1 % could be reached. The energy resolution amounted thereby to 22 % FWHM. A measurement of the energy resolution with 20 MeV protons yielded a value of 7 %. For the energy calibration of the single detector elements in a dynamic range between 1 MeV and 12 GeV with low-energy γ sources the charge response function of the photoelectron multiplier to be applied in the test module was determined in dependence on the light intensity. The measurement resulted that the photomultiplier at 40 MeV (related to a CsI(pure) reference crystal with an about twofold so high efficiency of the detectable light in comparison to the long pyramide trunks) deviates by 4 % and at 300 MeV by 38 % from the linear behaviour, while it at 500 MeV shows a deviation of 50 %

Measurements of the radiolytic oxidation of aqueous CsI using a sparging apparatus

International Nuclear Information System (INIS)

Ashmore, C.B.; Brown, D.; Sims, H.E.; Gwyther, J.R.

1996-01-01

Radiolytic oxidation is considered to be the main mechanism for the formation of I 2 from aqueous CsI in containment of a water cooled reactor after a LOCA. Despite the amount of study over the last 60 years on the radiation chemistry of iodine there has been no consistent set of experiments spanning a wide enough range of conditions to verify models with confidence. This paper describes results from a set of experiments carried out in order to remedy this deficiency. In this work the rate of evolution of I 2 from sparged irradiated CsI solution labeled with 131 I was measured on-line over a range of conditions. This work involved the measurement of the effects of pH, temperature, O 2 concentration, I - concentration, phosphate concentration, dose-rate and impurities on the rate of evolution of I 2 . The range of conditions was chosen in order to span as closely as possible conditions expected in a LOCA but also to help to elucidate some of the mechanisms especially at high pH. pH was found to be a very important factor influencing iodine volatility, over the temperature range studied the extent of oxidation reduced with temperature but this was compensated for by the decrease in partition coefficient. Oxygen concentration was more important in solutions not containing phosphate. The fractional oxidation was not particularly dependent on iodide concentration but G I2 was very dependent on [I - ]. There was no effect of added impurities, Fe, Mn, Mo or organics although in separate work silver was found to have a very important effect. During attempts to interpret the data it was found that it was necessary to include the iodine atom as a volatile species with a partition coefficient of 1.9 taken from thermodynamic data. The modelling work is described in a separate paper. (author) 15 figs., 1 tab., 19 refs

I Evolution of Environmental Costs Discolsur: A Study in Cellulose and Paper Companies - Members of Corporate Sustainability Index - CSI

Directory of Open Access Journals (Sweden)

Daniel Fonseca

2016-07-01

Full Text Available This research aimed to analyse, in relation to previous studies, the evolution of classification and disclosure of environmental costs on cellulose and paper companies listed on the CSI. The research, of a descriptive, documentary and qualitative nature, was based on content analysis of financial statements, accompanying notes, management reports and sustainability reports in the fiscal years 2010 to 2014. The results indicate that companies show environmental costs mainly in a qualitative way and of the positive type. The most part of this information is contained in the sustainability report. As to the classification, the highlighted environmental costs are of these types, (a prevention costs; (b internal failure costs; (c indirect costs; (d internal costs; (e costs for contingencies; (f potentially hidden costs; (g image and relationship costs, though not by these names. These results demonstrate a change, compared to previous studies on the quality and quantity of disclosure of environmental costs. It is suggested for future research the broadening of samples for other organizational activity sectors, with the aim of possible understanding of the Brazilian environment.

SSCL RFQ-DTL Matching Section instrumentation

International Nuclear Information System (INIS)

Datte, P.; Aielo, R.; Hayworth, M.

1993-11-01

A description of the SSCL RFQ-DTL Matching Section instrumentation is presented with emphasis on design issues and early instrumentation commissioning results. The H - beam energy through the RFQ-DTL matching section is 2.5 MeV, the beam current is 27 mA with a pulse width of 35 Its. The typical beam diameter is 3 mm. The instrumentation consists of three beam position monitors (BPM), a wire scanner, beam loss monitors (BLM), a slit and collector emittance measurement unit (EMU), a current toroid, and a Faraday cup. The instruments were designed to accommodate high current densities, have a large dynamic range with moderate bandwidths, and fit congested spaces

Heterologous gene expression and functional analysis of a type III polyketide synthase from Aspergillus niger NRRL 328

Energy Technology Data Exchange (ETDEWEB)

Kirimura, Kohtaro, E-mail: kkohtaro@waseda.jp; Watanabe, Shotaro; Kobayashi, Keiichi

2016-05-13

Type III polyketide synthases (PKSs) catalyze the formation of pyrone- and resorcinol-types aromatic polyketides. The genomic analysis of the filamentous fungus Aspergillus niger NRRL 328 revealed that this strain has a putative gene (chr-8-2: 2978617–2979847) encoding a type III PKS, although its functions are unknown. In this study, for functional analysis of this putative type III PKS designated as An-CsyA, cloning and heterologous expression of the An-CsyA gene (An-csyA) in Escherichia coli were performed. Recombinant His-tagged An-CsyA was successfully expressed in E. coli BL21 (DE3), purified by Ni{sup 2+}-affinity chromatography, and used for in vitro assay. Tests on the substrate specificity of the His-tagged An-CsyA with myriad acyl-CoAs as starter substrates and malonyl-CoA as extender substrate showed that His-tagged An-CsyA accepted fatty acyl-CoAs (C2-C14) and produced triketide pyrones (C2-C14), tetraketide pyrones (C2-C10), and pentaketide resorcinols (C10-C14). Furthermore, acetoacetyl-CoA, malonyl-CoA, isobutyryl-CoA, and benzoyl-CoA were also accepted as starter substrates, and both of triketide pyrones and tetraketide pyrones were produced. It is noteworthy that the His-tagged An-CsyA produced polyketides from malonyl-CoA as starter and extender substrates and produced tetraketide pyrones from short-chain fatty acyl-CoAs as starter substrates. Therefore, this is the first report showing the functional properties of An-CsyA different from those of other fungal type III PKSs. -- Highlights: •Type III PKS from Aspergillus niger NRRL 328, An-CsyA, was cloned and characterized. •An-CsyA produced triketide pyrones, tetraketide pyrones and pentaketide resorcinols. •Functional properties of An-CsyA differs from those of other fungal type III PKSs.

Heterologous gene expression and functional analysis of a type III polyketide synthase from Aspergillus niger NRRL 328

International Nuclear Information System (INIS)

Kirimura, Kohtaro; Watanabe, Shotaro; Kobayashi, Keiichi

2016-01-01

Type III polyketide synthases (PKSs) catalyze the formation of pyrone- and resorcinol-types aromatic polyketides. The genomic analysis of the filamentous fungus Aspergillus niger NRRL 328 revealed that this strain has a putative gene (chr-8-2: 2978617–2979847) encoding a type III PKS, although its functions are unknown. In this study, for functional analysis of this putative type III PKS designated as An-CsyA, cloning and heterologous expression of the An-CsyA gene (An-csyA) in Escherichia coli were performed. Recombinant His-tagged An-CsyA was successfully expressed in E. coli BL21 (DE3), purified by Ni"2"+-affinity chromatography, and used for in vitro assay. Tests on the substrate specificity of the His-tagged An-CsyA with myriad acyl-CoAs as starter substrates and malonyl-CoA as extender substrate showed that His-tagged An-CsyA accepted fatty acyl-CoAs (C2-C14) and produced triketide pyrones (C2-C14), tetraketide pyrones (C2-C10), and pentaketide resorcinols (C10-C14). Furthermore, acetoacetyl-CoA, malonyl-CoA, isobutyryl-CoA, and benzoyl-CoA were also accepted as starter substrates, and both of triketide pyrones and tetraketide pyrones were produced. It is noteworthy that the His-tagged An-CsyA produced polyketides from malonyl-CoA as starter and extender substrates and produced tetraketide pyrones from short-chain fatty acyl-CoAs as starter substrates. Therefore, this is the first report showing the functional properties of An-CsyA different from those of other fungal type III PKSs. -- Highlights: •Type III PKS from Aspergillus niger NRRL 328, An-CsyA, was cloned and characterized. •An-CsyA produced triketide pyrones, tetraketide pyrones and pentaketide resorcinols. •Functional properties of An-CsyA differs from those of other fungal type III PKSs.

A Monte Carlo study of backscattering effects in the photoelectron emission from CsI into CH$_{4}$ and Ar-CH$_{4}$ mixtures

CERN Document Server

Escada, J; Rachinhas, P J B M; Lopes, J A M; Santos, F P; Távora, L M N; Conde, C A N; Stauffer, A D

2007-01-01

Monte Carlo simulation is used to investigate photoelectron backscattering effects in the emission from a CsI photocathode into CH4 and Ar-CH4 mixtures for incident monochromatic photons with energies Eph in the range 6.8 eV to 9.8 eV (182 nm to 127 nm), and photons from a continuous VUV Hg(Ar) lamp with a spectral distribution peaked at Eph = 6.7 eV (185 nm), considering reduced applied electric fields E/N in the 0.1 Td to 40 Td range. The addition of CH4 to a noble gas efficiently increases electron transmission and drift velocity, due to vibrational excitation of the molecules at low electron energies. Results are presented for the photoelectron transmission efficiencies f, where f is the fraction of the number of photoelectrons emitted from CsI which are transmitted through the gas as compared to vacuum. The dependence of f on Eph, E/N, and mixture composition is analyzed and explained in terms of electron scattering in the different gas media, and results are compared with available measurements. Electro...

Geotechnical instrumentation requirements for atdepth testing and repository monitoring in tuff

International Nuclear Information System (INIS)

Zimmerman, R.M.

1983-01-01

This paper outlines geotechnical instrumentation requirements for the possible establishment of a nuclear waste repository in tuff on the Nevada Test Site (NTS). The Nuclear Regulatory Commission (NRC) has specified a continuing program to confirm performance during the operational period of the repository, which could last 50 years. Minimum required geotechnical measurements for confirmation of performance include thermal and thermomechanical responses; changes in stress, strain, and displacements; and pore pressure and groundwater flow characteristics. Conditions expected in tuff are: maximum rock temperatures of less than 250 0 C, stresses less than 100 MPa, strains between + or -0.01 mm/mm, and pore pressures less than 35 KPa in the unsaturated zone where hydraulic head is not the primary contributor. The paper describes instrumentation needed to make the desired measurements. In general, the instrumentation and data system are required to be stable and reliable for tens of years. Designs must consider requirements for temperature stability, temperature expansion compensation, moisture resistance, and long-term durability in mining-type environments. Severe requirements such as these suggest consideration of techniques for in-situ replacement of instrumentation. State-of-the-art instrumentation is briefly described along with a discussion of needs for refinement, replacement/recalibration and instrumentation development

Whole-core analysis by 13C NMR

International Nuclear Information System (INIS)

Vinegar, H.J.; Tutunjian, P.N.; Edelstein, W.A.; Roemer, P.B.

1991-01-01

This paper reports on a whole-core nuclear magnetic resonance (NMR) system that was used to obtain natural abundance 13 C spectra. The system enables rapid, nondestructive measurements of bulk volume of movable oil, aliphatic/aromatic ratio, oil viscosity, and organic vs. carbonate carbon. 13 C NMR can be used in cores where the 1 H NMR spectrum is too broad to resolve oil and water resonances separately. A 5 1/4-in. 13 C/ 1 H NMR coil was installed on a General Electric (GE) CSI-2T NMR imager/spectrometer. With a 4-in.-OD whole core, good 13 C signal/noise ratio (SNR) is obtained within minutes, while 1 H spectra are obtained in seconds. NMR measurements have been made of the 13 C and 1 H density of crude oils with a wide range of API gravities. For light- and medium-gravity oils, the 13 C and 1 H signal per unit volume is constant within about 3.5%. For heavy crudes, the 13 C and 1 H density measured by NMR is reduced by the shortening of spin-spin relaxation time. 13 C and 1 H NMR spin-lattice relaxation times were measured on a suite of Cannon viscosity standards, crude oils (4 to 60 degrees API), and alkanes (C 5 through C 16 ) with viscosities at 77 degrees F ranging from 0.5 cp to 2.5 x 10 7 cp. The 13 C and 1 H relaxation times show a similar correlation with viscosity from which oil viscosity can be estimated accurately for viscosities up to 100 cp. The 13 C surface relaxation rate for oils on water-wet rocks is very low. Nonproton decoupled 13 C NMR is shown to be insensitive to kerogen; thus, 13 C NMR measures only the movable hydrocarbon content of the cores. In carbonates, the 13 C spectrum also contains a carbonate powder pattern useful in quantifying inorganic carbon and distinguishing organic from carbonate carbon

CSI Frequency Domain Fingerprint-Based Passive Indoor Human Detection

Directory of Open Access Journals (Sweden)

Chong Han

2018-04-01

Full Text Available Passive indoor personnel detection technology is now a hot topic. Existing methods have been greatly influenced by environmental changes, and there are problems with the accuracy and robustness of detection. Passive personnel detection based on Wi-Fi not only solves the above problems, but also has the advantages of being low cost and easy to implement, and can be better applied to elderly care and safety monitoring. In this paper, we propose a passive indoor personnel detection method based on Wi-Fi, which we call FDF-PIHD (Frequency Domain Fingerprint-based Passive Indoor Human Detection. Through this method, fine-grained physical layer Channel State Information (CSI can be extracted to generate feature fingerprints so as to help determine the state in the scene by matching online fingerprints with offline fingerprints. In order to improve accuracy, we combine the detection results of three receiving antennas to obtain the final test result. The experimental results show that the detection rates of our proposed scheme all reach above 90%, no matter whether the scene is human-free, stationary or a moving human presence. In addition, it can not only detect whether there is a target indoors, but also determine the current state of the target.

Evaluation of radiation protection instrumentation: the C.T.H.I.R.. Poster and booklet for activity presentation

International Nuclear Information System (INIS)

Bicheron, G.; Ginisty, C.

1998-01-01

Among all the components required for radiation protection optimization, the evaluation of instrumentation is essential. The instrumentation in radiation protection allows to make the surveillance of personnel, installations and environment against the risk bound to radioactive contamination and ionizing radiations. The different devices can give the following functions: ambient dosimetry, (individual and environmental dosimetry), measurement of surface contaminations, air contamination by aerosols or gas, water contamination by liquid wastes,detection of criticality accidents, measurement of samples radioactivity. (N.C.)

Light trapping in a-Si/c-Si heterojunction solar cells by embedded ITO nanoparticles at rear surface

Science.gov (United States)

Dhar, Sukanta; Mandal, Sourav; Mitra, Suchismita; Ghosh, Hemanta; Mukherjee, Sampad; Banerjee, Chandan; Saha, Hiranmoy; Barua, A. K.

2017-12-01

The advantages of the amorphous silicon (a-Si)/crystalline silicon (c-Si) hetero junction technology are low temperature (oxide (ITO) nanoparticles embedded in amorphous silicon material at the rear side of the crystalline wafer. The nanoparticles were embedded in silicon to have higher scattering efficiency, as has been established by simulation studies. It has been shown that significant photocurrent enhancements (32.8 mA cm-2 to 35.1 mA cm-2) are achieved because of high scattering and coupling efficiency of the embedded nanoparticles into the silicon device, leading to an increase in efficiency from 13.74% to 15.22%. In addition, we have observed a small increase in open circuit voltage. This may be due to the surface passivation during the ITO nanoparticle formation with hydrogen plasma treatment. We also support our experimental results by simulation, with the help of a commercial finite-difference time-domain (FDTD) software solution.

Tropospheric Aerosol Radiative Forcing Observational eXperiment - University of Washington instrumented C-131A aircraft Data Set

Data.gov (United States)

National Aeronautics and Space Administration — TARFOX_UWC131A is the Tropospheric Aerosol Radiative Forcing Observational eXperiment (TARFOX) - University of Washington instrumented C-131A aircraft data set. The...

Exact Outage Probability of Dual-Hop CSI-Assisted AF Relaying Over Nakagami-m Fading Channels

KAUST Repository

Xia, Minghua

2012-10-01

In this correspondence, considering dual-hop channel state information (CSI)-assisted amplify-and-forward (AF) relaying over Nakagami- m fading channels, the cumulative distribution function (CDF) of the end-to-end signal-to-noise ratio (SNR) is derived. In particular, when the fading shape factors m1 and m2 at consecutive hops take non-integer values, the bivariate H-function and G -function are exploited to obtain an exact analytical expression for the CDF. The obtained CDF is then applied to evaluate the outage performance of the system under study. The analytical results of outage probability coincide exactly with Monte-Carlo simulation results and outperform the previously reported upper bounds in the low and medium SNR regions.

Economic policy instruments for the control of air pollution in Poland

International Nuclear Information System (INIS)

Bates, R.W.

1993-01-01

The World Bank is analyzing the role of economic policy instruments for the control of air pollution in Poland, in cooperation with Polish and international experts. The first stage, covering Poland as a whole, was recently completed, jointly financed with the U.S. E.P.A. and the Government of the Netherlands. The second stage, now under way, will extend the analysis into a specific regional framework. Stage 2 is financed by the World Bank, the Polish Government, and the U.K. Environment Know-How Fund. Air Pollution in Poland is overwhelmingly caused by energy production and uses, due to the fact that the Polish economy depends heavily on coal and lignite. At present, vehicles contribute less to total emissions than do coal burning and industrial processes, although they account for 25-35% of nitrogen oxides, carbon monoxide, hydrocarbons and lead; and the concentrated in areas of high population density. The paper shows how economic, technical and meteorological modelling can be used, to reach conclusions about cost-effective strategies for the control of emissions and the improvement of ambient air quality. A simulation approach is presented, to compare alternative policy instruments, in terms of their impact on emissions and control costs for Poland as a whole. The main instruments considered are open-quotes command-and-controlclose quotes regimes (C ampersand C) and economic incentives, namely fuel taxes, emissions taxes and emissions trading. Next, the paper describes how the analysis is being extended, to link emissions with ambient air quality, using air dispersion modelling, based on a case study for Krakow. Finally, some conclusions are drawn on the importance of sound economic policies for air quality management, the costs of alternative standards, C ampersand C approaches versus economic incentives, a practical strategy to develop an effective role for emissions taxes and trading, and the regional differentiation of policy instruments

Virucidal efficacy of peracetic acid for instrument disinfection

Directory of Open Access Journals (Sweden)

Britta Becker

2017-11-01

. However, a dramatically decrease of titer after the drying and immerging could be observed. In consequence, a four log reduction of poliovirus titer could not be achieved in the carrier test. Conclusion In summary, 1500 ppm PAA at 35 °C was necessary for a virucidal action in the quantitative suspension test. After passing the requirements of the suspension test, additional examinations with adeno- and murine norovirus on glass carriers based on prEN 17111:2017 will not additionally contribute to the final claim of an instrument disinfectant for virucidal efficacy. This is due to the great stability of poliovirus in the preceded quantitative suspension test and the fact that poliovirus could not serve as test virus in the following carrier assay.

A large area CsI RICH Detector in ALICE at LHC

CERN Document Server

Di Bari, D; Davenport, Martyn; Di Mauro, A; Elia, D; Ghidini, B; Grimaldi, A; Martinengo, P; Monno, E; Morsch, Andreas; Nappi, E; Paic, G; Piuz, François; Posa, F; Santiard, Jean-Claude; Stucchi, S; Tomasicchio, G; Williams, T D

1999-01-01

A 1m2 CsI RICH prototype has been successfully tested in a hadron beam at CERN SPS. The prototype, fully equipped with 15k electronic channels, has been used to identify particles coming from pi-Be interactions. Track reconstruction has been performed by using a telescope consisting of four gas pad chambers. A detailed description of the detector will be presented and results from the test will be discussed.List of figuresFigure 1 Expected proton and antiproton yields including jet quenching mechanism in central Pb-Pb collisions at LHC.Figure 2 Schematic view of the HMPID CsI-RICHFigure 3 Experimental layout used at the SPS/H4 test beamFigure 4 Distributions of the mean number, per ring, of pad hits (Npad), electrons (Ntot) and Cherenkov photoelectrons (Nres) as a function of the single-electron mean pulse heightFigure 5 Mean single-electron pulse height as a function of high voltage measured at the centre of each of the four photocathodesFigure 6 Evaluation of the uniformity of the chamber gain for the photo...

PILA: Sub-Meter Localization Using CSI from Commodity Wi-Fi Devices.

Science.gov (United States)

Tian, Zengshan; Li, Ze; Zhou, Mu; Jin, Yue; Wu, Zipeng

2016-10-10

The aim of this paper is to present a new indoor localization approach by employing the Angle-of-arrival (AOA) and Received Signal Strength (RSS) measurements in Wi-Fi network. To achieve this goal, we first collect the Channel State Information (CSI) by using the commodity Wi-Fi devices with our designed three antennas to estimate the AOA of Wi-Fi signal. Second, we propose a direct path identification algorithm to obtain the direct signal path for the sake of reducing the interference of multipath effect on the AOA estimation. Third, we construct a new objective function to solve the localization problem by integrating the AOA and RSS information. Although the localization problem is non-convex, we use the Second-order Cone Programming (SOCP) relaxation approach to transform it into a convex problem. Finally, the effectiveness of our approach is verified based on the prototype implementation by using the commodity Wi-Fi devices. The experimental results show that our approach can achieve the median error 0.7 m in the actual indoor environment.

On-line induced absorption measurement on PbWO.sub.4./sub., YAlO.sub.3./sub.:Ce and CsI scintillating crystals

Czech Academy of Sciences Publication Activity Database

Šulc, M.; Nikl, Martin; Vognar, M.; Blažek, K.; Nejezchleb, K.; Boháček, Pavel; Nitsch, Karel; Kobayashi, M.; Usuki, Y.; Shen, D.

2004-01-01

Roč. 38, - (2004), s. 393-396 ISSN 1350-4487 R&D Projects: GA ČR(CZ) GA202/01/0753 Grant - others:NATO SfP(XX) 973510-Scintillators Institutional research plan: CEZ:AV0Z1010914 Keywords : radiation damage * PbWO 4 scintillator * YAlO 3 :Ce * CsI Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.664, year: 2004

Synthesis of 3,5-diisopropyl[carboxy-14C]salicylic acid and its 67Cu complex

International Nuclear Information System (INIS)

Chidambaram, M.V.; Epperson, C.E.; Williams, S.; Gray, R.A.; Sorenson, J.R.J.

1991-01-01

The synthesis of 3,5-diisopropyl[carboxy- 14 C]salicylic acid was achieved via Kolbe-Schmitt carboxylation of potassium 2,4-di-isopropylphenolate. The yield of this acid was 81% based upon the weight of the product and 93% based upon radioactivity incorporated into the labeled acid which contains 98% 14 C in the carboxyl group (specific activity = 5.1 μCi/mg). The labeled acid was characterized by ultraviolet spectrophotometry and purity established by thin-layer chromatography, autoradiography, and liquid scintillation counting. A 90% yield of the double labeled 14 C, 67 Cu-complex (specific activity = 4.6 μCi 67 Cu/mg) was obtained using conditions developed with non-radioactive reactants. The presence of 67 Cu in this complex was established using γ-ray emission spectrophometry. (author)

The Development of 2700-3000 F Environmental Barrier Coatings for SiC/SiC Ceramic Matrix Composites: Challenges and Opportunities

Science.gov (United States)

Zhu, Dongming

2015-01-01

Environmental barrier coatings (EBCs) and SiCSiC ceramic matrix composites (CMCs) systems will play a crucial role in future turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures, reduce engine weight and cooling requirements. The development of prime-reliant environmental barrier coatings is a key to enable the applications of the envisioned 2700-3000F EBC - CMC systems to help achieve next generation engine performance and durability goals. This paper will primarily address the performance requirements and design considerations of environmental barrier coatings for turbine engine applications. The emphasis is placed on current NASA candidate environmental barrier coating systems for SiCSiC CMCs, their performance benefits and design limitations in long-term operation and combustion environments. The efforts have been also directed to developing prime-reliant, self-healing 2700F EBC bond coat; and high stability, lower thermal conductivity, and durable EBC top coats. Major technical barriers in developing environmental barrier coating systems, the coating integrations with next generation CMCs having the improved environmental stability, cyclic durability, erosion-impact resistance, and long-term system performance will be described. The research and development opportunities for turbine engine environmental barrier coating systems by utilizing improved compositions, state-of-the-art processing methods, and simulated environment testing and durability modeling will be discussed.

Determination of the Antibiotic Oxytetracycline in Commercial Milk by Solid-Phase Extraction: A High-Performance Liquid Chromatography (HPLC) Experiment for Quantitative Instrumental Analysis

Science.gov (United States)

Mei-Ratliff, Yuan

2012-01-01

Trace levels of oxytetracylcine spiked into commercial milk samples are extracted, cleaned up, and preconcentrated using a C[subscript 18] solid-phase extraction column. The extract is then analyzed by a high-performance liquid chromatography (HPLC) instrument equipped with a UV detector and a C[subscript 18] column (150 mm x 4.6 mm x 3.5 [mu]m).…

Focal plane instrument for the Solar UV-Vis-IR Telescope aboard SOLAR-C

Science.gov (United States)

Katsukawa, Yukio; Suematsu, Yoshinori; Shimizu, Toshifumi; Ichimoto, Kiyoshi; Takeyama, Norihide

2011-10-01

It is presented the conceptual design of a focal plane instrument for the Solar UV-Vis-IR Telescope (SUVIT) aboard the next Japanese solar mission SOLAR-C. A primary purpose of the telescope is to achieve precise as well as high resolution spectroscopic and polarimetric measurements of the solar chromosphere with a big aperture of 1.5 m, which is expected to make a significant progress in understanding basic MHD processes in the solar atmosphere. The focal plane instrument consists of two packages: A filtergraph package is to get not only monochromatic images but also Dopplergrams and magnetograms using a tunable narrow-band filter and interference filters. A spectrograph package is to perform accurate spectro-polarimetric observations for measuring chromospheric magnetic fields, and is employing a Littrow-type spectrograph. The most challenging aspect in the instrument design is wide wavelength coverage from 280 nm to 1.1 μm to observe multiple chromospheric lines, which is to be realized with a lens unit including fluoride glasses. A high-speed camera for correlation tracking of granular motion is also implemented in one of the packages for an image stabilization system, which is essential to achieve high spatial resolution and high polarimetric accuracy.

Low cost back contact heterojunction solar cells on thin c-Si wafers. integrating laser and thin film processing for improved manufacturability

Energy Technology Data Exchange (ETDEWEB)

Hegedus, Steven S. [Univ. of Delaware, Newark, DE (United States)

2015-09-08

An interdigitated back contact (IBC) Si wafer solar cell with deposited a-Si heterojunction (HJ) emitter and contacts is considered the ultimate single junction Si solar cell design. This was confirmed in 2014 by both Panasonic and Sharp Solar producing IBC-HJ cells breaking the previous record Si solar cell efficiency of 25%. But manufacturability at low cost is a concern for the complex IBC-HJ device structure. In this research program, our goals were to addressed the broad industry need for a high-efficiency c-Si cell that overcomes the dominant module cost barriers by 1) developing thin Si wafers synthesized by innovative, kerfless techniques; 2) integrating laser-based processing into most aspects of solar cell fabrication, ensuring high speed and low thermal budgets ; 3) developing an all back contact cell structure compatible with thin wafers using a simplified, low-temperature fabrication process; and 4) designing the contact patterning to enable simplified module assembly. There were a number of significant achievements from this 3 year program. Regarding the front surface, we developed and applied new method to characterize critical interface recombination parameters including interface defect density Dit and hole and electron capture cross-section for use as input for 2D simulation of the IBC cell to guide design and loss analysis. We optimized the antireflection and passivation properties of the front surface texture and a-Si/a-SiN/a-SiC stack depositions to obtain a very low (< 6 mA/cm2) front surface optical losses (reflection and absorption) while maintaining excellent surface passivation (SRV<5 cm/s). We worked with kerfless wafer manufacturers to apply defect-engineering techniques to improve bulk minority-carrier lifetime of thin kerfless wafers by both reducing initial impurities during growth and developing post-growth gettering techniques. This led insights about the kinetics of nickel, chromium, and dislocations in PV-grade silicon and to

Low cost back contact heterojunction solar cells on thin c-Si wafers. Integrating laser and thin film processing for improved manufacturability

Energy Technology Data Exchange (ETDEWEB)

Hegedus, Steven S. [Univ. of Delaware, Newark, DE (United States)

2015-09-08

An interdigitated back contact (IBC) Si wafer solar cell with deposited a-Si heterojunction (HJ) emitter and contacts is considered the ultimate single junction Si solar cell design. This was confirmed in 2014 by both Panasonic and Sharp Solar producing IBC-HJ cells breaking the previous record Si solar cell efficiency of 25%. But manufacturability at low cost is a concern for the complex IBC-HJ device structure. In this research program, our goals were to addressed the broad industry need for a high-efficiency c-Si cell that overcomes the dominant module cost barriers by 1) developing thin Si wafers synthesized by innovative, kerfless techniques; 2) integrating laser-based processing into most aspects of solar cell fabrication, ensuring high speed and low thermal budgets ; 3) developing an all back contact cell structure compatible with thin wafers using a simplified, low-temperature fabrication process; and 4) designing the contact patterning to enable simplified module assembly. There were a number of significant achievements from this 3 year program. Regarding the front surface, we developed and applied new method to characterize critical interface recombination parameters including interface defect density Dit and hole and electron capture cross-section for use as input for 2D simulation of the IBC cell to guide design and loss analysis. We optimized the antireflection and passivation properties of the front surface texture and a-Si/a-SiN/a-SiC stack depositions to obtain a very low (< 6 mA/cm2) front surface optical losses (reflection and absorption) while maintaining excellent surface passivation (SRV<5 cm/s). We worked with kerfless wafer manufacturers to apply defect-engineering techniques to improve bulk minority-carrier lifetime of thin kerfless wafers by both reducing initial impurities during growth and developing post-growth gettering techniques. This led insights about the kinetics of nickel, chromium, and dislocations in PV-grade silicon and to

CSI, de la série au jeu : « a more immersive experience »

OpenAIRE

Monnet-Cantagrel, Hélène

2016-01-01

CSI est une franchise de séries policières construites autour d’un même principe narratif de résolution des enquêtes par les techniques scientifiques d’investigation. D’objectif ouvertement commercial, de l’ordre du marketing, et répétitives, les franchises de médias n’ont pas toujours bonne presse, accusées de consacrer la transformation des biens culturels en produits industriels. Les franchises sont pourtant une pratique de plus en plus fréquente à la télévision - américaine - qui, depuis ...

Trajectories for spacecraft encounters with Comet Honda-Mrkos-Pajdusakova in 1996

Science.gov (United States)

Dunham, David W.; Jen, Shao-Chiang; Farquhar, Robert W.

1989-01-01

Early in 1996, the relatively bright short-period Comet Honda-Mrkos-Pajdusakova (HMP) will pass only 0.17 astronomical unit from the earth, providing both an unusually favorable apparition for ground-based observers and an opportunity for a spacecraft to reach Comet HMP on relatively low-energy trajectories. The Japanense Institute of Space and Astronautical Sciences Sakigake spacecraft is expected to fly by Comet HMP on February 3, 1996, after utilizing four earth swingbys to modify its orbit. If the camera on the ESA Giotto spacecraft is inoperable, Giotto may also be sent to Comet HMP. In addition, 1-year earth-return trajectories to Comet HMP are described, along with some that can be extended to encounter Comet Giacobini-Zinner in 1998.

C-myb Plays an Essential Role in the Protective Function of IGF-1 on Cytotoxicity Induced by Aβ25-35 via the PI3K/Akt Pathway.

Science.gov (United States)

Zhang, Jingyu; Shu, Yongwei; Qu, Yang; Zhang, Lina; Chu, Tingting; Zheng, Yonghui; Zhao, Hong

2017-12-01

There have been numerous reports about neurodegenerative diseases, including Alzheimer's disease. Nevertheless, the molecules responsible for the neurodegeneration in Alzheimer's disease are basically unknown. Recent findings indicate that the cellular myeloblastosis (c-myb) regulates neural progenitor cell proliferation. In the current study, the function of insulin-like growth factor-1 (IGF-1) against cell toxicity in SH-SY5Y cells induced by β-amyloid 25-35 (Aβ 25-35 ) and its molecular mechanism were investigated. It was found that p25 protein production was raised by Aβ 25-35 (25 μM), similar to the increased expression of μ-calpain. The results also showed that Aβ 25-35 reduced c-myb, elevated tau hyper-phosphorylation, and induced death of SH-SY5Y cells. Loss of cell viability and apoptosis of SH-SY5Y cells induced by Aβ 25-35 were attenuated by IGF-1 pretreatment in a dose-dependent manner. In addition, IGF-1 blocked μ-calpain expression, which was induced by Aβ 25-35 and reduced p25 formation and tau hyper-phosphorylation. Moreover, the expression of c-myb in SH-SY5Y cells was increased by combining IGF-1 with Aβ 25-35 or IGF-1 alone. The neuroprotective function of IGF-1 was attenuated in the SH-SY5Y cells, which were transfected with a c-myb small interfering RNA. Furthermore, LY294002, a specific PI3K inhibitor, reduced c-myb expression and abolished IGF-1's protective function in SH-SY5Y cell apoptosis induced by Aβ 25-35 . The facts above indicate that c-myb has a role in IGF-1-mediated protection from Aβ 25-35 -induced cytotoxicity via the PI3K/Akt pathway.

Hypoxic preconditioning with cobalt of bone marrow mesenchymal stem cells improves cell migration and enhances therapy for treatment of ischemic acute kidney injury.

Directory of Open Access Journals (Sweden)

Xiaofang Yu

Full Text Available Mesenchymal stem cell (MSC administration is known to enhance the recovery of the kidney following injury. Here we tested the potential of hypoxic-preconditioned-MSC transplantation to enhance the efficacy of cell therapy on acute kidney injury (AKI by improving MSC migration to the injured kidney. Cobalt was used as hypoxia mimetic preconditioning (HMP. MSC were subjected to HMP through 24 h culture in 200 µmol/L cobalt. Compared to normoxia cultured MSC (NP-MSC, HMP significantly increased the expression of HIF-1α and CXCR4 in MSC and enhanced the migration of MSC in vitro. This effect was lost when MSC were treated with siRNA targeting HIF-1α or CXCR4 antagonist. SPIO labeled MSC were administered to rats with I/R injury followed immediately by magnetic resonance imaging. Imaging clearly showed that HMP-MSC exhibited greater migration and a longer retention time in the ischemic kidney than NP-MSC. Histological evaluation showed more HMP-MSC in the glomerular capillaries of ischemic kidneys than in the kidneys receiving NP-MSC. Occasional tubules showed iron labeling in the HMP group, while no tubules had iron labeling in NP group, indicating the possibility of tubular transdifferentiation after HMP. These results were also confirmed by fluorescence microscopy study using CM-DiI labeling. The increased recruitment of HMP-MSC was associated with reduced kidney injury and enhanced functional recovery. This effect was also related to the increased paracrine action by HMP-MSC. Thus we suggest that by enhancing MSC migration and prolonging kidney retention, hypoxic preconditioning of MSC may be a useful approach for developing AKI cell therapy.

Instrument evaluation no. 11. ESI nuclear model 271 C contamination monitor

CERN Document Server

Burgess, P H

1978-01-01

The various radiations encountered in radiological protection cover a wide range of energies and radiation measurements have to he carried out under an equally broad spectrum of environmental conditions. This report is one of a series intended to give information on the performance characteristics of radiological protection instruments, to assist in the selection of appropriate instruments for a given purpose, to interpret the results obtained with such instruments, and, in particular, to know the likely sources and magnitude of errors that might be associated with measurements in the field. The radiation, electrical and environmental characteristics of radiation protection instruments are considered together with those aspects of the construction which make an instrument convenient for routine use. To provide consistent criteria for instrument performance, the range of tests performed on any particular class of instrument, the test methods and the criteria of acceptable performance are based broadly on the a...

Analysis of customer satisfaction in hospital by using Importance-Performance Analysis (IPA and Customer Satisfaction Index (CSI

Directory of Open Access Journals (Sweden)

Helia Vembri Noor

2018-01-01

Full Text Available As a major health referral centre, the hospital demanded to provide comprehensive services provided by a multi-disciplinary team according to the needs of patient. In the expansion of a growing number of hospitals in Yogyakarta especially Sleman area where retreat acquire customers even more stringent, it is necessary to increase the quality of services. There are five determinants of service quality namely: reliability, responsiveness, assurance, empathy, and tangible. Collecting data is done by observation and distributing questionnaires to 70 respondents, and Importance-Performance Analysis and Customer Satisfaction Index are used to determine satisfaction level of outpatients. As a results, six out of twenty attributes need improvement, namely: a The condition of the hospital is clean, comfortable and tidy; b Guidance and information boards poly is easy to see and read; c The ease and accuracy of obtaining information for patients (referrals, lab results, etc.; d The hospital staff has a quick response to the needs of patients; e Attention physicians in managing patients and willingness to provide a particular time for consultation; and f The prescribed medication is suitable and safe. It is known that the value of CSI by 76% means the service is not satisfied the patient.

In vivo single-shot (13)C spectroscopic imaging of hyperpolarized metabolites by spatiotemporal encoding

DEFF Research Database (Denmark)

Schmidt, Rita; Laustsen, Christoffer; Dumez, Jean-Nicolas

2014-01-01

are necessary. Several approaches have been customized for hyperpolarized (13)C MRI, including CSI with a center-out k-space encoding, EPSI, and spectrally selective pulses in combination with spiral EPI acquisitions. Recent studies have described the potential of single-shot alternatives based...... temporal) data sets were obtained at 7T from a murine lymphoma tumor model....

Modelling on c-Si/a-Si:H wire solar cells: some key parameters to optimize the photovoltaic performance

Directory of Open Access Journals (Sweden)

Alvarez J.

2012-07-01

Full Text Available Solar cells based on silicon nano- or micro-wires have attracted much attention as a promising path for low cost photovoltaic technology. The key point of this structure is the decoupling of the light absorption from the carriers collection. In order to predict and optimize the performance potential of p- (or n- doped c-Si/ n-(or p- doped a-Si:H nanowire-based solar cells, we have used the Silvaco-Atlas software to model a single-wire device. In particular, we have noticed a drastic decrease of the open-circuit voltage (Voc when increasing the doping density of the silicon core beyond an optimum value. We present here a detailed study of the parameters that can alter the Voc of c-Si(p/a-Si:H (n wires according to the doping density in c-Si. A comparison with simulation results obtained on planar c-Si/a-Si:H heterojunctions shows that the drop in Voc, linked to an increase of the dark current in both structures, is more pronounced for radial junctions due to geometric criteria. These numerical modelling results have lead to a better understanding of transport phenomena within the wire.

Lower virus infections in Varroa destructor-infested and uninfested brood and adult honey bees (Apis mellifera) of a low mite population growth colony compared to a high mite population growth colony.

Science.gov (United States)

Emsen, Berna; Hamiduzzaman, Mollah Md; Goodwin, Paul H; Guzman-Novoa, Ernesto

2015-01-01

A comparison was made of the prevalence and relative quantification of deformed wing virus (DWV), Israeli acute paralysis virus (IAPV), black queen cell virus (BQCV), Kashmir bee virus (KBV), acute bee paralysis virus (ABPV) and sac brood virus (SBV) in brood and adult honey bees (Apis mellifera) from colonies selected for high (HMP) and low (LMP) Varroa destructor mite population growth. Two viruses, ABPV and SBV, were never detected. For adults without mite infestation, DWV, IAPV, BQCV and KBV were detected in the HMP colony; however, only BQCV was detected in the LMP colony but at similar levels as in the HMP colony. With mite infestation, the four viruses were detected in adults of the HMP colony but all at higher amounts than in the LMP colony. For brood without mite infestation, DWV and IAPV were detected in the HMP colony, but no viruses were detected in the LMP colony. With mite infestation of brood, the four viruses were detected in the HMP colony, but only DWV and IAPV were detected and at lower amounts in the LMP colony. An epidemiological explanation for these results is that pre-experiment differences in virus presence and levels existed between the HMP and LMP colonies. It is also possible that low V. destructor population growth in the LMP colony resulted in the bees being less exposed to the mite and thus less likely to have virus infections. LMP and HMP bees may have also differed in susceptibility to virus infection.

The Somatic Complaints List: Validation of a self-report questionnaire assessing somatic complaints in children

NARCIS (Netherlands)

Jellesma, F. C.; Rieffe, C.J.; Meerum Terwogt, M.

2007-01-01

Objective: To evaluate the Somatic Complaint List (SCL) in children. Method: At T1, 365 fourth and 352 fifth graders completed the SCL, the Children's Somatization Inventory (CSI-C), and the Mood Questionnaire. Parents (n=564) completed the parental form of the CSI-C (CSI-P). Six months later, the

Heavy fragments emission in the 84Kr on 12C reaction at 35 MeV/nucleon

International Nuclear Information System (INIS)

Mittig, W.; Cunsolo, A.; Foti, A.; Wieleczko, J.P.; Auger, F.; Berthier, B.; Pascaud, J.M.; Quebert, J.; Plagnol, E.

1984-01-01

Heavy residues of collisions of 84 Kr + 12 C at 35 MeV/amu were measured using time of flight ΔE-E telescopes. An important part of the total cross-section leads to events that have all the characteristics of an equilibrated composite system decaying by heavy fragments emission. The experimental yields are well reproduced using a statistical model

Synthesis of [35]Adamanzane, 1,5,9,13-Tetraazabicyclo [7.7.3]nonadecane, by Oxidative C-N Cleavage of [36]Adamanzane, 1,5,9,13-Tetraazatricyclo[7.7.3.35,13]docosane and Crystal Structure of the Tetraprotonated Bromide Salt of [35]Adamanzane

DEFF Research Database (Denmark)

Springborg, Johan; Pretzmann, Ulla; Nielsen, Bente

1998-01-01

. The four acidic hydrogen atoms are all oriented away from the cavity. The concentration acid dissociation constants of H4[35]adz4+ were determined by potentiometric glass-electrode measurements and 1H and 13C NMR spectroscopy: pKa1=1-2, pKa3=9.65(2) and pKa4=12.09(4) (1 M NaBr, 25 degrees C)....

Deuterium trapping in the carbon-silicon co-deposition layers prepared by RF sputtering in D2 atmosphere

Science.gov (United States)

Zhang, Hongliang; Zhang, Weiyuan; Su, Ranran; Tu, Hanjun; Shi, Liqun; Hu, Jiansheng

2018-04-01

Deuterated carbon-silicon layers co-deposited on graphite and silicon substrates by radio frequency magnetron sputtering in pure D2 plasma were produced to study deuterium trapping and characteristics of the C-Si layers. The C-Si co-deposited layers were examined by ion beam analysis (IBA), Raman spectroscopy (RS), infrared absorption (IR) spectroscopy, thermal desorption spectroscopy (TDS) and scanning electron microscopy (SEM). It was found that the growth rate of the C-Si co-deposition layer decreased with increasing temperature from 350 K to 800 K, the D concentration and C/Si ratios increased differently on graphite and silicon substrates. TDS shows that D desorption is mainly as D2, HD, HDO, CD4, and C2D4 and release peaks occurred at temperatures of less than 900 K. RS and IR analysis reveal that the structure of the C-Si layers became more disordered with increasing temperatures. Rounded areas of peeling with 1-2 μm diameters were observed on the surface.

The SUVIT Instrument on the Solar-C Mission

Science.gov (United States)

Tarbell, Theodore D.; Ichimoto, Kiyoshi

2014-06-01

Solar-C is a new space mission being proposed to JAXA, with significant contributions anticipated from NASA, ESA, and EU countries. The main scientific objectives are to: reveal the mechanisms for heating and dynamics of the chromosphere and corona and acceleration of the solar wind; determine the physical origin of the large-scale explosions and eruptions that drive short-term solar, heliospheric, and geospace variability; use the solar atmosphere as a laboratory for understanding fundamental physical processes; make unprecedented observations of the polar magnetic fields. The unique approaches of Solar-C to achieve these goals are to: determine the properties and evolution of the 3-dimensional magnetic field, especially on small spatial scales, and for the first time observed in the crucial low beta plasma region; observe all the temperature regimes of the atmosphere seamlessly at the highest spatial resolution ever achieved; observe at high cadence the prevailing dynamics in all regions of the atmosphere; determine physical properties from high resolution spectroscopic measurements throughout the atmosphere and into the solar wind. The powerful suite of instruments onboard Solar-C will be sensitive to temperatures from the photosphere 5500 K) to solar flares 20 MK) with no temperature gap, with spatial resolution at all temperatures of 0.3″ or less (0.1″ in the lower atmosphere) and at high cadence. The purpose of the Solar UV-Visible-IR Telescope (SUVIT) is to obtain chromospheric velocity, temperature, density and magnetic field diagnostics over as wide arange of heights as possible, through high cadence spectral line profiles and vector spectro-polarimetry. SUVIT is a meter-class telescope currently under study at 1.4m in order to obtain sufficientresolution and S/N. SUVIT has two complementary focal plane packages, the Filtergraph that makes high cadence imaging observations with the highest spatial resolution and the Spectro-polarimeter that makes

Outage Probability versus Fairness Trade-off in Opportunistic Relay Selection with Outdated CSI

Directory of Open Access Journals (Sweden)

Vicario JoseLopez

2009-01-01

Full Text Available We analyze the existing trade-offs in terms of system performance versus fairness of a cooperative system based on opportunistic relay selection (ORS and with outdated channel state information (CSI. In particular, system performance is analytically evaluated in terms of outage probability, and the fairness behavior is assessed based on the power consumption at the different relays. In order to improve the fairness behavior of ORS while keeping the selection diversity gain, we propose a relay selection mechanism where the relay with the highest normalized signal-to-noise ratio (SNR is selected for relaying the source's information. The proposed strategy is compared with existing relay selection strategies by adopting a novel graphical representation inspired by expected profit versus risk plots used in modern portfolio theory. As shown in the paper, this strategy allows operating the system in more favorable points of the outage versus fairness region.

40 CFR 35.2218 - Project performance.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Project performance. 35.2218 Section 35... STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2218 Project performance. (a... personnel; and (3) Advise the grantee whether the project is meeting the project performance standards. (c...

CSI-Chocolate Science Investigation and the Case of the Recipe Rip-Off: Using an Extended Problem-Based Scenario to Enhance High School Students' Science Engagement

Science.gov (United States)

Marle, Peter D.; Decker, Lisa; Taylor, Victoria; Fitzpatrick, Kathleen; Khaliqi, David; Owens, Janel E.; Henry, Renee M.

2014-01-01

This paper discusses a K-12/university collaboration in which students participated in a four-day scenario-based summer STEM (science, technology, engineering, and mathematics) camp aimed at making difficult scientific concepts salient. This scenario, Jumpstart STEM-CSI: Chocolate Science Investigation (JSCSI), used open- and guided-inquiry…

Magnetic resonance butterfly coils: Design and application for hyperpolarized 13C studies

DEFF Research Database (Denmark)

Giovannetti, Giulio; Frijia, Francesca; Attanasio, Simona

2013-01-01

Hyperpolarized 13C magnetic resonance spectroscopy in pig models enables cardiac metabolism assessment and provides a powerful tool for heart physiology studies, although the low molar concentration of derivate metabolites gives rise to technological limitations in terms of data quality. The desi...... throughout the volume of interest for cardiac imaging in pig. Experimental SNR-vs-depth profiles, extracted from the [1-13C]acetate phantom chemical shift image (CSI), permitted to highlight the performance of the proposed coils configuration. © 2013 Elsevier Ltd. All rights reserved....

Report of the Instrumentation Service - Annex C; Prilog C - Izvestaj o radu sluzbe instrumentacije

Energy Technology Data Exchange (ETDEWEB)

Majstorovic, D [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1987-12-15

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment related to experimental facilities. [Serbo-Croat] Ovaj izvestaj opisuje zadatke i organizaciju rada sluzbe za instrumentaciju. Osnovni zadatak sluzbe je kontrola i odrzavanje osnovne kontrolno-merne opreme sistema za upravljanje i zastitu, sistema za tehnolosku kontrolu, sistema za dozimetrijsku kontrolu. Pored toga izvestaj sadrzi podatke o kontroli i odrzavanju ostale elektronske opreme, prenosne, servisne i eksperimentalne instrumentacije prema ukazanoj potrebi.

The SiC hardware of the Sentinel-2 multi spectral instrument

Science.gov (United States)

Bougoin, Michel; Lavenac, Jérôme

2017-11-01

The Sentinel-2 mission is a major part of the GMES (Global Monitoring for Environment and Security) program which has been set up by the European Union, on a joint initiative with the European Space Agency. A pair of identical satellites will observe the earth from a sun-synchronous orbit at 786 km altitude. Astrium is the prime contractor of the satellites and their payload. The MultiSpectral Instrument features a "all-SiC" TMA (Three Mirror Anastygmat) telescope. MSI will provide optical images in 13 spectral bands, in the visible and also the near infra-red range, with a 10 to 60 m resolution and a 290 km wide swath. The Boostec® SiC material is used mainly for its high specific stiffness (Youngs modulus / density) and its high thermal stability (thermal conductivity / coefficient of thermal expansion) which allow to reduce the distortions induced by thermo-elastic stresses. Its high mechanical properties as well as the relevant technology enable to make not only the mirrors but also the structure which holds them and the elements of the focal plane (including some detectors packaging). Due to the required large size, accuracy and shape complexity, developing and manufacturing some of these SiC parts required innovative manufacturing approach. It is reviewed in the present paper.

SiC materials: a semiconductor family for the next century

Science.gov (United States)

Camassel, Jean; Contreras, Sylvie; Robert, Jean-Louis

2000-03-01

The current status of SiC semiconductor materials is reviewed, with emphasize on forthcoming applications. In a first part one focuses on the most important physical properties. Then, power device and micro-opto-electronic applications, using both 4H and 6H-SiC, are presented. Technological problems which have to be solved in order to realize simple planar device are considered. Emphasize is set on the French and European efforts, and on the USA and Japan's ones. In a second part, one deals with advanced high temperature industrial sensor applications. Interest for cubic 3C-SiC eposited on Silicon On Insulator (SOI) is demonstrated and results of comparative examinations of different 3CSiC/SOI materials are briefly given.

Lower Virus Infections in Varroa destructor-Infested and Uninfested Brood and Adult Honey Bees (Apis mellifera) of a Low Mite Population Growth Colony Compared to a High Mite Population Growth Colony

Science.gov (United States)

Emsen, Berna; Hamiduzzaman, Mollah Md.; Goodwin, Paul H.; Guzman-Novoa, Ernesto

2015-01-01

A comparison was made of the prevalence and relative quantification of deformed wing virus (DWV), Israeli acute paralysis virus (IAPV), black queen cell virus (BQCV), Kashmir bee virus (KBV), acute bee paralysis virus (ABPV) and sac brood virus (SBV) in brood and adult honey bees (Apis mellifera) from colonies selected for high (HMP) and low (LMP) Varroa destructor mite population growth. Two viruses, ABPV and SBV, were never detected. For adults without mite infestation, DWV, IAPV, BQCV and KBV were detected in the HMP colony; however, only BQCV was detected in the LMP colony but at similar levels as in the HMP colony. With mite infestation, the four viruses were detected in adults of the HMP colony but all at higher amounts than in the LMP colony. For brood without mite infestation, DWV and IAPV were detected in the HMP colony, but no viruses were detected in the LMP colony. With mite infestation of brood, the four viruses were detected in the HMP colony, but only DWV and IAPV were detected and at lower amounts in the LMP colony. An epidemiological explanation for these results is that pre-experiment differences in virus presence and levels existed between the HMP and LMP colonies. It is also possible that low V. destructor population growth in the LMP colony resulted in the bees being less exposed to the mite and thus less likely to have virus infections. LMP and HMP bees may have also differed in susceptibility to virus infection. PMID:25723540

CONTAIN code calculations of the effects on the source term of CsI to I/sub 2/ conversion due to severe hydrogen burns

International Nuclear Information System (INIS)

Valdez, G.D.; Williams, D.C.

1986-01-01

In experiments conducted at Sandia National Laboratories large amounts of elemental iodine were produced when CsI-Al 2 O 3 aerosol was exposed to hydrogen/air combustion. To evaluate some of the implications of the iodide conversion (observed to occur with up to 75% efficiency) for the severe accident source term, computational simulations of representative accident sequences were conducted with the CONTAIN code. The following conclusions can be drawn from this preliminary source term assessment: (1) If the containment sprays are inoperative during the accident, or failed by the hydrogen burn, the late-time source term is almost tripled when the iodide is converted to I 2 . (2) With the sprays active, the amount released without conversion of the CsI aerosol is 63% higher than for the case when conversion occurs. (3) For the case where CsI is converted to I 2 continued operation of the sprays reduces the release by a factor of 40, relative to the case in which the sprays fail at the time of the hydrogen burn. When there is no conversion, the reduction factor for continued spray operation is about a factor of 9, relative to the failed spray case

Chemical interaction of B4C, B, and C with Mo/Si layered structures

International Nuclear Information System (INIS)

Rooij-Lohmann, V. I. T. A. de; Veldhuizen, L. W.; Zoethout, E.; Yakshin, A. E.; Kruijs, R. W. E. van de; Thijsse, B. J.; Gorgoi, M.; Schaefers, F.; Bijkerk, F.

2010-01-01

To enhance the thermal stability, B 4 C diffusion barrier layers are often added to Mo/Si multilayer structures for extreme ultraviolet optics. Knowledge about the chemical interaction between B 4 C and Mo or Si, however is largely lacking. Therefore, the chemical processes during annealing up to 600 deg. C of a Mo/B 4 C/Si layered structure have been investigated in situ with hard x-ray photoelectron spectroscopy and ex situ with depth profiling x-ray photoelectron spectroscopy. Mo/B/Si and Mo/C/Si structures have also been analyzed as reference systems. The chemical processes in these systems have been identified, with two stages being distinguished. In the first stage, B and C diffuse and react predominantly with Mo. MoSi x forms in the second stage. If the diffusion barrier consists of C or B 4 C, a compound forms that is stable up to the maximum probed temperature and annealing time. We suggest that the diffusion barrier function of B 4 C interlayers as reported in literature can be caused by the stability of the formed compound, rather than by the stability of B 4 C itself.

On the secrecy capacity of the broadcast wiretap channel with limited CSI feedback

KAUST Repository

Hyadi, Amal

2016-10-27

In this paper, we investigate the problem of secure broadcasting over block-fading channels with limited channel knowledge at the transmitter. More particularly, we analyze the effect of having imperfect channel state information (CSI) via a finite rate feedback on the throughput of a broadcast channel where the transmission is intended for multiple legitimate receivers in the presence of an eavesdropper. First, we partially characterize the ergodic secrecy capacity of the system when the source broadcasts the same information to all the receivers, i.e., common message transmission. Then, we look at the independent messages case, where the transmitter broadcasts multiple independent messages to the legitimate receivers. For this case, we present lower and upper bounds on the ergodic secrecy sum-capacity. In both scenarios, we show that the proposed lower and upper bounds coincide asymptotically as the capacity of the feedback links becomes large, hence, fully characterizing the secrecy capacity in this case.

On the secrecy capacity of the broadcast wiretap channel with limited CSI feedback

KAUST Repository

Hyadi, Amal; Rezki, Zouheir; Alouini, Mohamed-Slim

2016-01-01

In this paper, we investigate the problem of secure broadcasting over block-fading channels with limited channel knowledge at the transmitter. More particularly, we analyze the effect of having imperfect channel state information (CSI) via a finite rate feedback on the throughput of a broadcast channel where the transmission is intended for multiple legitimate receivers in the presence of an eavesdropper. First, we partially characterize the ergodic secrecy capacity of the system when the source broadcasts the same information to all the receivers, i.e., common message transmission. Then, we look at the independent messages case, where the transmitter broadcasts multiple independent messages to the legitimate receivers. For this case, we present lower and upper bounds on the ergodic secrecy sum-capacity. In both scenarios, we show that the proposed lower and upper bounds coincide asymptotically as the capacity of the feedback links becomes large, hence, fully characterizing the secrecy capacity in this case.

catena-Poly[[tetrakis(hexamethylphosphoramide-κObis(nitrato-κ2O,O′lanthanum(III] [silver(I-di-μ2-sulfido-tungstate(VI-di-μ2-sulfido

Directory of Open Access Journals (Sweden)

Lude Lu

2008-02-01

Full Text Available Hexamethylphosphoramide (hmp, tetrathiotungstate(VI, silver sulfide and lanthanum(III nitrate are self-assembled to form discrete cations one-dimensional poylmeric anionic chains [AgWS4]nn− in the title compound, {[La(NO32(C6H18N3OP4][AgWS4]}n. The central La atom in the cation is coordinated by eight O atoms from two nitrate and four hmp ligands. Together with the two nitrate ligands, the cation is monovalent, which leads to the anionic chain having a monovalent repeat unit. The polymeric anionic chain with W...Ag...W and Ag...W...Ag angles of 165.94 (3 and 155.894 (14° presents a distorted linear configuration. Five N atoms, 18 C atoms and their attached H atoms are disordered equally over two positions.

Spectroellipsometric detection of silicon substrate damage caused by radiofrequency sputtering of niobium oxide

Science.gov (United States)

Lohner, Tivadar; Serényi, Miklós; Szilágyi, Edit; Zolnai, Zsolt; Czigány, Zsolt; Khánh, Nguyen Quoc; Petrik, Péter; Fried, Miklós

2017-11-01

Substrate surface damage induced by deposition of metal atoms by radiofrequency (rf) sputtering or ion beam sputtering onto single-crystalline silicon (c-Si) surface has been characterized earlier by electrical measurements. The question arises whether it is possible to characterize surface damage using spectroscopic ellipsometry (SE). In our experiments niobium oxide layers were deposited by rf sputtering on c-Si substrates in gas mixture of oxygen and argon. Multiple angle of incidence spectroscopic ellipsometry measurements were performed, a four-layer optical model (surface roughness layer, niobium oxide layer, native silicon oxide layer and ion implantation-amorphized silicon [i-a-Si] layer on a c-Si substrate) was created in order to evaluate the spectra. The evaluations yielded thicknesses of several nm for the i-a-Si layer. Better agreement could be achieved between the measured and the generated spectra by inserting a mixed layer (with components of c-Si and i-a-Si applying the effective medium approximation) between the silicon oxide layer and the c-Si substrate. High depth resolution Rutherford backscattering (RBS) measurements were performed to investigate the interface disorder between the deposited niobium oxide layer and the c-Si substrate. Atomic resolution cross-sectional transmission electron microscopy investigation was applied to visualize the details of the damaged subsurface region of the substrate.

Experimental study of the pion-xenon nucleus collisions at 3.5 GeV/c. Neutral pion production

International Nuclear Information System (INIS)

Strugalski, Z.; Abrosimov, A.T.; Wosinska, K.; Pawlak, T.; Nluta, J.; Sredniawa, B.; Il'ina, A.N.; Okhrimenko, L.S.; Peryt, W.; Miller, K.

1983-01-01

Experimental investigations of the neutral pion production are performed in pion-xenon collisions at 3.5 GeV/c. It is obtained that: 1) the average neutral pion multiplicity changes with the multiplicity of the protons emitted; 2) nearly 20% of the pions produced are emitted into the backward hemisphere; 3) the energy spectrum of the neutral pions is smooth; 4) the longitudinal component of the neutral pion momentum changes within the limits from -600 MeV/c to +1800 MeV/c; 5) the average value of the transversal component of the neutral pion momentum changes with the multiplicity of the protons emitted from approximately 270 to approximately 170 MeV/c; 6) the average value of the cosine of the neutral pion emission angle decreases with the multiplicity of the protons emitted

Luminescence of solar cells with a-Si:H/c-Si heterojunctions

Science.gov (United States)

Zhigunov, D. M.; Il'in, A. S.; Forsh, P. A.; Bobyl', A. V.; Verbitskii, V. N.; Terukov, E. I.; Kashkarov, P. K.

2017-05-01

We have studied the electroluminescence (EL) and photoluminescence (PL) of solar cells containing a-Si:H/c-Si heterojunctions. It is established that both the EL and PL properties of these cells are determined by the radiative recombination of nonequilibrium carriers in crystalline silicon (c-Si). The external EL energy yield (efficiency) of solar cells with a-Si:H/c-Si heterojunctions at room temperature amounts to 2.1% and exceeds the value reached in silicon diode structures. This large EL efficiency can be explained by good passivation of the surface of crystalline silicon and the corresponding increase in lifetime of minority carrier s in these solar cells.

De una sociología de la mediación a una pragmática de las vinculaciones. Retrospectiva de un recorrido sociológico dentro del CSI

Directory of Open Access Journals (Sweden)

Antoine Hennion

2017-08-01

Full Text Available Este artículo enfoca sobre un retorno reflexivo en mi propia trayectoria en el CSI. Mi propósito no es fijar la historia sino releerla desde las preocupaciones presentes. Desde su fundación por L. Karpik en 1967, el CSI abogó por tomar seriamente las realidades que estaba investigando (derecho, ciencia y tecnología, negocios, cultura. Bajo el título de un posible “retorno al objeto” en sociología, discuto convergencias y diferencias en el trabajo de campo emprendido, por un lado, sobre la ciencia y tecnología (STS, y por el otro sobre la cultura: por ejemplo, el uso de términos como traducción o mediación, o la relación diferente con la sociología crítica de Bourdieu, que no tuvo el mismo impacto en cada campo. Luego considero la emergencia de los enfoques pragmatistas en Francia en los años noventa y la gran variedad de concepciones a las que dieron lugar, en particular a través de debates con grupos cercanos como el GSPM y el CEMS en la EHESS de Paris, sobre el estatuto de los objetos, y examinando la influencia de las teorías de la acción provenientes de Estados Unidos. Apoyándome en esta genealogía, muestro cómo las aseveraciones del pragmatismo han informado mi propio trabajo con los aficionados y las vinculaciones, y discute en definitiva la importancia para la sociología de volverse más sensible respecto a los objetos de los que se ocupa.

C-terminal truncations in human 3'-5' DNA exonuclease TREX1 cause autosomal dominant retinal vasculopathy with cerebral leukodystrophy

NARCIS (Netherlands)

Richards, Anna; van den Maagdenberg, Arn M. J. M.; Jen, Joanna C.; Kavanagh, David; Bertram, Paula; Spitzer, Dirk; Liszewski, M. Kathryn; Barilla-LaBarca, Maria-Louise; Terwindt, Gisela M.; Kasai, Yumi; McLellan, Mike; Grand, Mark Gilbert; Vanmolkot, Kaate R. J.; de Vries, Boukje; Wan, Jijun; Kane, Michael J.; Mamsa, Hafsa; Schäfer, Ruth; Stam, Anine H.; Haan, Joost; de Jong, Paulus T. V. M.; Storimans, Caroline W.; van Schooneveld, Mary J.; Oosterhuis, Jendo A.; Gschwendter, Andreas; Dichgans, Martin; Kotschet, Katya E.; Hodgkinson, Suzanne; Hardy, Todd A.; Delatycki, Martin B.; Hajj-Ali, Rula A.; Kothari, Parul H.; Nelson, Stanley F.; Frants, Rune R.; Baloh, Robert W.; Ferrari, Michel D.; Atkinson, John P.

2007-01-01

Autosomal dominant retinal vasculopathy with cerebral leukodystrophy is a microvascular endotheliopathy with middle-age onset. In nine families, we identified heterozygous C-terminal frameshift mutations in TREX1, which encodes a 3'-5' exonuclease. These truncated proteins retain exonuclease

MBO3: Eu3+ at the rate SiO2 (M = Y, Gd and Al) nano down conversion phosphors with superior asymmetric ratio and colour purity as spectral converters for c-Si solar cells

International Nuclear Information System (INIS)

Rambabu, U.; Munirathnam, N.R.; Prakash, T.L.

2013-01-01

Y 1-x BO 3 :Eu x 3+ (0.07 ≤ x ≤ 0.5 mol) and Y 0.72x (Gd x , Al x )BO 3 : Eu 3+ 0.3 (0.05 ± x ± 0.3 mol) powder phosphors have been synthesized by a novel co-precipitation technique followed by heat treatment. Luminescence optimization was done: by optimizing the dopant Eu 3+ -concentration, substitution of Y 3+ with Gd 3+ /Al 3+ and finally with SiO 2 shell coating. Due to nanosize particle distribution, the optimum activator (Eu 3+ ) concentration (30 mol %) was found to be extremely at higher level, compared to the bulk phosphors. The asymmetric ratio (Red/Orange) and color purity of the optimized phosphors, Y 0.7 BO 3 :Eu 0.3 3+ (with crystallite size, D = 32 nm) and Y 0.3 Gd 0.2 Al 0.2 BO 3 :Eu 3+ (D = 17 nm) were further enhanced with SiO 2 shell coating. Based on the systematic study, the nanophosphor Y 0.7 BO 3 :Eu 0.3 3+ at the rate SiO 2 with R/O ratio as 6.710 and color coordinates (x = 0.6612, y = 0.3357) was optimized as a remarkable phosphor having superior features for its application in thin transparent form as DC layer to improve the energy conversion efficiency of c-Si solar cells

Microstructure and Wear Resistance of TiC Composite Coating in situ Synthesized on 35CrMnSi Steel by Argon Arc Cladding%35CrMnSi 表面氩弧熔覆原位自生 TiC 复合涂层的组织及耐磨性

Institute of Scientific and Technical Information of China (English)

丁天; 孟君晟; 乔盛楠; 吕东亮; 宋永平; 李阳

2014-01-01

Objective To improve the wear resistance of cutting tooth and to prolong its service life. Methods The TiC enhanced nickel-based composite coating was prepared on the surface of 35CrMnSi steel by argon arc cladding technique. The microstructure of the coating was analyzed by OM, SEM and XRD. Microhardness and wear resistance at room temperature of the composite coat-ing were examined by means of microhardness testing and impact abrasion resistance testing, respectively. Results The compact microstructure was obtained in the composite coating, and good metallurgical bonding could be obtained between the 35CrMnSi steel and cladding coating, with the main phases of TiC, γ-Ni and M23 C6 . The majority of TiC was blocky. The TiC particles was about 1 ~ 2 μm in size and the particles were dispersed in the coatings. The hardness and wear resistance of the coating were related with the (Ti+C) content. The highest hardness of 20% (Ti+C) coating was 1190HV. The relative wear resistance of the composite coating was 7. 5 times higher than that of 35CrMnSi steel. Conclusion The cladding coating reinforced by TiC particle showed ap-parently improved surface hardness as compared to 35CrMnSi steel. The wear mechanism of the composite coating under impact loading at room temperature was micro-cutting wear. The wear resistance of coating was greatly increased by argon arc cladding.%目的：提高截齿的耐磨性,延长其使用寿命。方法利用氩弧熔覆技术在35CrMnSi 钢表面制备 TiC 增强镍基复合涂层,分析涂层的显微组织和物相组成,测试涂层在室温下的显微硬度和耐磨性,并分析磨损机制。结果氩弧熔覆涂层的显微组织致密均匀,涂层与基体呈冶金结合,主要由 TiC,γ-Ni, M23 C6等物相组成。 TiC 颗粒呈块状,尺寸为1~2μm,弥散分布在涂层中。涂层硬度和耐磨性与(Ti+C)含量有关,熔覆粉末中(Ti+C)质量分数为20%时,涂层最高硬度可达1190HV,耐磨性达到基体的7.5�

Design and construction of an instrument for measuring thermistor electrical characteristic

International Nuclear Information System (INIS)

Budiono; Yudi Herdiana

2007-01-01

In this work an instrument for measuring the electrical characteristic of thermistor has been designed and constructed. The instrument was constructed from main components i.e. a micro controller AT89C51, 3 ADC-0804, a LM35 temperature sensor and IC MAX 232. The IC MAX 232 component is used to connect the micro controller to the personal computer serially by using RS-232 standard. While ADC-0804 was used to convert the analog data (DC voltage) to the digital one so that the data was readable by the micro controller. Digital data from 3 ADC-0804 circuit which have been read by the micro controller was sent directly to the personal computer. The data from the measurement which have been stored in the personal computer was then processed to know the value of temperature and measured thermistor resistance. The processed data could be either stored in a data base or displayed in a monitor or printed in the form of table data and in the form a graph of thermistor resistance as the function of temperature. The result of measurement from measuring instrument of the characteristic of thermistor electric's had been made, being compared by measuring calibrated instrument, the deviation is about 0.33 %. (author)

Report of the Instrumentation Service - Annex C; Prilog C - Izvestaj o radu sluzbe instrumentacija

Energy Technology Data Exchange (ETDEWEB)

Majstorovic, D [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1986-12-01

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related to renewal of the equipment. [Serbo-Croat] Ovaj izvestaj opisuje zadatke i organizaciju rada sluzbe za instrumentaciju. Osnovni zadatak sluzbe je kontrola i odrzavanje osnovne kontrolno-merne opreme sistema za upravljanje i zastitu, sistema za tehnolosku kontrolu, sistema za dozimetrijsku kontrolu. Pored toga izvestaj sadrzi podatke o kontroli i odrzavanju ostale elektronske opreme, inspekciju stanja reaktorskog suda i bazena za skladistenje ozracenih gorivnih elemenata kao i aktivnosti vezanih za obnavljanje opreme.

Report of the Instrumentation Service - Annex C; Prilog C - Izvestaj o radu sluzbe instrumentacije

Energy Technology Data Exchange (ETDEWEB)

Majstorovic, D [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1989-12-15

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related to renewal of the equipment. [Serbo-Croat] Ovaj izvestaj opisuje zadatke i organizaciju rada sluzbe za instrumentaciju. Osnovni zadatak sluzbe je kontrola i odrzavanje osnovne kontrolno-merne opreme sistema za upravljanje i zastitu, sistema za tehnolosku kontrolu, sistema za dozimetrijsku kontrolu. Pored toga izvestaj sadrzi podatke o kontroli i odrzavanju ostale elektronske opreme, inspekciju stanja reaktorskog suda i bazena za skladistenje ozracenih gorivnih elemenata kao i aktivnosti vezanih za obnavljanje opreme.

Report of the Instrumentation Service - Annex C; Prilog C - Izvestaj o radu sluzbe instrumentacije

Energy Technology Data Exchange (ETDEWEB)

Majstorovic, D [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1988-12-15

This report describes the tasks and organizational structure of the Instrumentation service. The most important task of this Service is control and maintenance of the reactor control and protection instruments, operation control, and dosimetry system. Besides data about this basic instrumentation, the report includes data about control and maintenance of other electronic equipment, inspection of the reactor vessel and spent fuel storage pool and describes activities related to renewal of the equipment. [Serbo-Croat] Ovaj izvestaj opisuje zadatke i organizaciju rada sluzbe za instrumentaciju. Osnovni zadatak sluzbe je kontrola i odrzavanje osnovne kontrolno-merne opreme sistema za upravljanje i zastitu, sistema za tehnolosku kontrolu, sistema za dozimetrijsku kontrolu. Pored toga izvestaj sadrzi podatke o kontroli i odrzavanju ostale elektronske opreme, inspekciju stanja reaktorskog suda i bazena za skladistenje ozracenih gorivnih elemenata kao i aktivnosti vezanih za obnavljanje opreme.

Rapid development of stable transgene CHO cell lines by CRISPR/Cas9-mediated site-specific integration into C12orf35.

Science.gov (United States)

Zhao, Menglin; Wang, Jiaxian; Luo, Manyu; Luo, Han; Zhao, Meiqi; Han, Lei; Zhang, Mengxiao; Yang, Hui; Xie, Yueqing; Jiang, Hua; Feng, Lei; Lu, Huili; Zhu, Jianwei

2018-07-01

Chinese hamster ovary (CHO) cells are the most widely used mammalian hosts for recombinant protein production. However, by conventional random integration strategy, development of a high-expressing and stable recombinant CHO cell line has always been a difficult task due to the heterogenic insertion and its caused requirement of multiple rounds of selection. Site-specific integration of transgenes into CHO hot spots is an ideal strategy to overcome these challenges since it can generate isogenic cell lines with consistent productivity and stability. In this study, we investigated three sites with potential high transcriptional activities: C12orf35, HPRT, and GRIK1, to determine the possible transcriptional hot spots in CHO cells, and further construct a reliable site-specific integration strategy to develop recombinant cell lines efficiently. Genes encoding representative proteins mCherry and anti-PD1 monoclonal antibody were targeted into these three loci respectively through CRISPR/Cas9 technology. Stable cell lines were generated successfully after a single round of selection. In comparison with a random integration control, all the targeted integration cell lines showed higher productivity, among which C12orf35 locus was the most advantageous in both productivity and cell line stability. Binding affinity and N-glycan analysis of the antibody revealed that all batches of product were of similar quality independent on integrated sites. Deep sequencing demonstrated that there was low level of off-target mutations caused by CRISPR/Cas9, but none of them contributed to the development process of transgene cell lines. Our results demonstrated the feasibility of C12orf35 as the target site for exogenous gene integration, and strongly suggested that C12orf35 targeted integration mediated by CRISPR/Cas9 is a reliable strategy for the rapid development of recombinant CHO cell lines.

Sequential meta-C-H olefination of synthetically versatile benzyl silanes: effective synthesis of meta-olefinated toluene, benzaldehyde and benzyl alcohols.

Science.gov (United States)

Patra, Tuhin; Watile, Rahul; Agasti, Soumitra; Naveen, Togati; Maiti, Debabrata

2016-02-04

Tremendous progress has been made towards ortho-selective C-H functionalization in the last three decades. However, the activation of distal C-H bonds and their functionalization has remained fairly underdeveloped. Herein, we report sequential meta-C-H functionalization by performing selective mono-olefination and bis-olefination with late stage modification of the C-Si as well as Si-O bonds. Temporary silyl connection was found to be advantageous due to its easy installation, easy removal and wide synthetic diversification.

Biocompatible transferrin-conjugated sodium hexametaphosphate-stabilized gold nanoparticles: synthesis, characterization, cytotoxicity and cellular uptake

International Nuclear Information System (INIS)

Parab, Harshala J; Huang, Jing-Hong; Liu, Ru-Shi; Lai, Tsung-Ching; Jan, Yi-Hua; Wang, Jui-Ling; Hsiao, Michael; Chen, Chung-Hsuan; Hwu, Yeu-Kuang; Tsai, Din Ping; Chuang, Shih-Yi; Pang, Jong-Hwei S

2011-01-01

The feasibility of using gold nanoparticles (AuNPs) for biomedical applications has led to considerable interest in the development of novel synthetic protocols and surface modification strategies for AuNPs to produce biocompatible molecular probes. This investigation is, to our knowledge, the first to elucidate the synthesis and characterization of sodium hexametaphosphate (HMP)-stabilized gold nanoparticles (Au-HMP) in an aqueous medium. The role of HMP, a food additive, as a polymeric stabilizing and protecting agent for AuNPs is elucidated. The surface modification of Au-HMP nanoparticles was carried out using polyethylene glycol and transferrin to produce molecular probes for possible clinical applications. In vitro cell viability studies performed using as-synthesized Au-HMP nanoparticles and their surface-modified counterparts reveal the biocompatibility of the nanoparticles. The transferrin-conjugated nanoparticles have significantly higher cellular uptake in J5 cells (liver cancer cells) than control cells (oral mucosa fibroblast cells), as determined by inductively coupled plasma mass spectrometry. This study demonstrates the possibility of using an inexpensive and non-toxic food additive, HMP, as a stabilizer in the large-scale generation of biocompatible and monodispersed AuNPs, which may have future diagnostic and therapeutic applications.

Biocompatible transferrin-conjugated sodium hexametaphosphate-stabilized gold nanoparticles: synthesis, characterization, cytotoxicity and cellular uptake

Energy Technology Data Exchange (ETDEWEB)

Parab, Harshala J; Huang, Jing-Hong; Liu, Ru-Shi [Department of Chemistry, National Taiwan University, Taipei 106, Taiwan (China); Lai, Tsung-Ching; Jan, Yi-Hua; Wang, Jui-Ling; Hsiao, Michael; Chen, Chung-Hsuan [Genomics Research Center, Academia Sinica, Taipei 115, Taiwan (China); Hwu, Yeu-Kuang [Institute of Physics, Academia Sinica, Taipei 115, Taiwan (China); Tsai, Din Ping [Department of Physics, National Taiwan University, Taipei 106, Taiwan (China); Chuang, Shih-Yi; Pang, Jong-Hwei S, E-mail: rsliu@ntu.edu.tw, E-mail: mhsiao@gate.sinica.edu.tw [Graduate Institute of Clinical Medical Sciences, Chang Gung University, Tao-Yuan, Taiwan (China)

2011-09-30

The feasibility of using gold nanoparticles (AuNPs) for biomedical applications has led to considerable interest in the development of novel synthetic protocols and surface modification strategies for AuNPs to produce biocompatible molecular probes. This investigation is, to our knowledge, the first to elucidate the synthesis and characterization of sodium hexametaphosphate (HMP)-stabilized gold nanoparticles (Au-HMP) in an aqueous medium. The role of HMP, a food additive, as a polymeric stabilizing and protecting agent for AuNPs is elucidated. The surface modification of Au-HMP nanoparticles was carried out using polyethylene glycol and transferrin to produce molecular probes for possible clinical applications. In vitro cell viability studies performed using as-synthesized Au-HMP nanoparticles and their surface-modified counterparts reveal the biocompatibility of the nanoparticles. The transferrin-conjugated nanoparticles have significantly higher cellular uptake in J5 cells (liver cancer cells) than control cells (oral mucosa fibroblast cells), as determined by inductively coupled plasma mass spectrometry. This study demonstrates the possibility of using an inexpensive and non-toxic food additive, HMP, as a stabilizer in the large-scale generation of biocompatible and monodispersed AuNPs, which may have future diagnostic and therapeutic applications.

20 CFR 402.35 - Publication.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Publication. 402.35 Section 402.35 Employees... Publication. (a) Methods of publication. Materials we are required to publish pursuant to the provisions of 5 U.S.C. 552 (a)(1) and (a)(2), we publish in one of the following ways: (1) By publication in the...

Microhydration of caesium compounds: Cs, CsOH, CsI and Cs₂I₂ complexes with one to three H₂O molecules of nuclear safety interest.

Science.gov (United States)

Sudolská, Mária; Cantrel, Laurent; Cernušák, Ivan

2014-04-01

Structure and thermodynamic properties (standard enthalpies of formation and Gibbs free energies) of hydrated caesium species of nuclear safety interest, Cs, CsOH, CsI and its dimer Cs₂I₂, with one up to three water molecules, are calculated to assess their possible existence in severe accident occurring to a pressurized water reactor. The calculations were performed using the coupled cluster theory including single, double and non-iterative triple substitutions (CCSD(T)) in conjunction with the basis sets (ANO-RCC) developed for scalar relativistic calculations. The second-order spin-free Douglas-Kroll-Hess Hamiltonian was used to account for the scalar relativistic effects. Thermodynamic properties obtained by these correlated ab initio calculations (entropies and thermal capacities at constant pressure as a function of temperature) are used in nuclear accident simulations using ASTEC/SOPHAEROS software. Interaction energies, standard enthalpies and Gibbs free energies of successive water molecules addition determine the ordering of the complexes. CsOH forms the most hydrated stable complexes followed by CsI, Cs₂I₂, and Cs. CsOH still exists in steam atmosphere even at quite high temperature, up to around 1100 K.

3D Imaging of Dielectric Objects Buried under a Rough Surface by Using CSI

Directory of Open Access Journals (Sweden)

Evrim Tetik

2015-01-01

Full Text Available A 3D scalar electromagnetic imaging of dielectric objects buried under a rough surface is presented. The problem has been treated as a 3D scalar problem for computational simplicity as a first step to the 3D vector problem. The complexity of the background in which the object is buried is simplified by obtaining Green’s function of its background, which consists of two homogeneous half-spaces, and a rough interface between them, by using Buried Object Approach (BOA. Green’s function of the two-part space with planar interface is obtained to be used in the process. Reconstruction of the location, shape, and constitutive parameters of the objects is achieved by Contrast Source Inversion (CSI method with conjugate gradient. The scattered field data that is used in the inverse problem is obtained via both Method of Moments (MoM and Comsol Multiphysics pressure acoustics model.

Radiation protection instrument 1993

International Nuclear Information System (INIS)

1993-04-01

The Radiation Protection Instrument, 1993 (Legislative Instrument 1559) prescribes the powers and functions of the Radiation Protection Board established under the Ghana Atomic Energy Commission by the Atomic Energy Commission (Amendment) Law, 1993 (P.N.D.C. Law 308). Also included in the Legislative Instrument are schedules on control and use of ionising radiation and radiation sources as well as procedures for notification, licensing and inspection of ionising radiation facilities. (EAA)

Homemade thermometry instruments in the field.

Science.gov (United States)

Pasquier, Mathieu; Rousson, Valentin; Zen Ruffinen, Grégoire; Hugli, Olivier

2012-03-01

Esophageal temperature is the gold standard for in-the-field temperature monitoring in hypothermic victims with cardiac arrest. For practical reasons, some mountain rescue teams use homemade esophageal thermometers to measure esophageal temperature; these consist of nonmedical inside/outside temperature monitoring instruments that have been modified to allow for esophageal insertion. We planned a study to determine the accuracy of such thermometers. Two of the same model of digital cabled indoor/outdoor thermometer were modified and tested in comparison with a reference thermometer. The thermometers were tested in a water bath at different temperatures between 10°C and 35.2°C. Three hundred measurements were taken with each thermometer. Our experimental study showed that both homemade thermometers provided a good correlation and a clinically acceptable agreement in comparison with the reference thermometer. Measurements were within 0.5°C in comparison with the reference thermometer 97.5% of the time. The homemade thermometers performed well in vitro, in comparison with a reference thermometer. However, because these devices in their original form are not designed for clinical use, their use should be restricted to situations when the use of a conventional esophageal thermometer is impossible. Copyright © 2012 Wilderness Medical Society. Published by Elsevier Inc. All rights reserved.

Neutron instrumentation for biology

Energy Technology Data Exchange (ETDEWEB)

Mason, S.A. [Institut Laue-Langevin, Grenoble (France)

1994-12-31

In the October 1994 round of proposals at the ILL, the external biology review sub- committee was asked to allocate neutron beam time to a wide range of experiments, on almost half the total number of scheduled neutron instruments: on 3 diffractometers, on 3 small angle scattering instruments, and on some 6 inelastic scattering spectrometers. In the 3.5 years since the temporary reactor shutdown, the ILL`s management structure has been optimized, budgets and staff have been trimmed, the ILL reactor has been re-built, and many of the instruments up-graded, many powerful (mainly Unix) workstations have been introduced, and the neighboring European Synchrotron Radiation Facility has established itself as the leading synchrotron radiation source and has started its official user program. The ILL reactor remains the world`s most intense dedicated neutron source. In this challenging context, it is of interest to review briefly the park of ILL instruments used to study the structure and energetics of small and large biological systems. A brief summary will be made of each class of experiments actually proposed in the latest ILL proposal round.

Examining the free radical bonding mechanism of benzoquinone– and hydroquinone–methanol passivation of silicon surfaces

International Nuclear Information System (INIS)

Kotulak, Nicole A.; Chen, Meixi; Schreiber, Nikolas; Jones, Kevin; Opila, Robert L.

2015-01-01

Highlights: • Photons are required for high levels of c-Si passivation by both BQ/ME and HQ/ME solutions. • Protons are required for high levels of c-Si passivation by both BQ/ME and HQ/ME solutions. • The free radical QH· is the likely passivating species for c-Si surfaces from BQ/ME and HQ/ME solutions. - Abstract: The surface passivation of p-benzoquinone (BQ) and hydroquinone (HQ) when dissolved in methanol (ME) has been examined through effective lifetime testing of crystalline silicon (c-Si) wafers treated with the aforementioned solutions. Changes in the availability of both photons and protons in the solutions were demonstrated to affect the level of passivation achieved. The requirement of both excess protons and ambient light exposure to maintain high effective lifetimes supports the presence of a free radical species that drives the surface passivation. Surface analysis suggests a 1:1 ratio of HQ-like bonds to methoxy bonds on the c-Si surface after treatment with a BQ/ME solution.

Protein kinase C involvement in the acetylcholine release reduction induced by amyloid-beta(25-35) aggregates on neuromuscular synapses.

Science.gov (United States)

Tomàs, Marta; Garcia, Neus; Santafé, Manuel M; Lanuza, Maria; Tomàs, Josep

2009-01-01

Using intracellular recording of the diaphragm muscle of adult rats, we have investigated the short-term functional effects of amyloid-beta (Abeta(25-35) peptide aggregates on the modulation of acetylcholine (ACh) release and the involvement of protein kinase C (PKC). The non-aggregated form of this peptide does not change the evoked and spontaneous transmitter release parameters on the neuromuscular synapse. However, the aggregated form of Abeta(25-35) acutely interferes with evoked quantal ACh release (approximately 40% reduction) when synaptic activity in the ex vivo neuromuscular preparation is maintained by low frequency (1 Hz) electrical stimulation. This effect is partially dependent on the activity of PKC that may have a permissive action. The end result of Abeta(25-35) is in opposition to the PKC-dependent maintenance effect on ACh release manifested in active synapses.

OBSERVATIONS OF BINARY STARS WITH THE DIFFERENTIAL SPECKLE SURVEY INSTRUMENT. I. INSTRUMENT DESCRIPTION AND FIRST RESULTS

International Nuclear Information System (INIS)

Horch, Elliott P.; Veillette, Daniel R.; Shah, Sagar C.; O'Rielly, Grant V.; Baena Galle, Roberto; Van Altena, William F.

2009-01-01

First results of a new speckle imaging system, the Differential Speckle Survey Instrument, are reported. The instrument is designed to take speckle data in two filters simultaneously with two independent CCD imagers. This feature results in three advantages over other speckle cameras: (1) twice as many frames can be obtained in the same observation time which can increase the signal-to-noise ratio for astrometric measurements, (2) component colors can be derived from a single observation, and (3) the two colors give substantial leverage over atmospheric dispersion, allowing for subdiffraction-limited separations to be measured reliably. Fifty-four observations are reported from the first use of the instrument at the Wisconsin-Indiana-Yale-NOAO 3.5 m Telescope 9 The WIYN Observatory is a joint facility of the University of Wisconsin-Madison, Indiana University, Yale University, and the National Optical Astronomy Observatories. in 2008 September, including seven components resolved for the first time. These observations are used to judge the basic capabilities of the instrument.

24 CFR 35.1335 - Standard treatments.

Science.gov (United States)

2010-04-01

... Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1335 Standard treatments. Standard..., such as metal coil stock, plastic, polyurethane, or linoleum. (c) Correcting dust-generating conditions... examination shall be performed in accordance with § 35.1340 at the conclusion of any lead hazard reduction...

Passive hypothermia (≥35 - newborns with hypoxic-ischaemic encephalopathy.

Science.gov (United States)

Sellam, Aurélie; Lode, Noëlla; Ayachi, Azzedine; Jourdain, Gilles; Dauger, Stéphane; Jones, Peter

2017-01-01

Hypothermia initiated in the first six hours of life in term infants with hypoxic ischemic encephalopathy reduces the risk of death and severe neurological sequelae. Our study's principal objective was to evaluate transport predictors potentially influencing arrival in NICU (Neonatal Intensive Care Unit) at a temperature ≥35-Newborns were selected for inclusion according to biological and clinical criteria before transport using passive hypothermia using a target temperature of ≥35-<36°C. Data on 120 of 126 inclusions were available for analysis. Thirty-three percent of the children arrived in NICU with the target temperature of ≥35-<36°C. The mean temperature for the whole group of infants on arrival in NICU was 35.4°C (34.3-36.5). The median age of all infants on arrival in NICU was 3h03min [2h25min-3h56min]. Three infants arrived in NICU with a temperature of <33°C and eleven with a temperature ≥37°C. Adrenaline during resuscitation was associated with a lower mean temperature on arrival in NICU. Our strategy using ≥35-<36°C passive hypothermia combined with short transport times had little effect on temperature after the arrival of Neonatal Transport Team although did reduce numbers of infants arriving in NICU in deep hypothermia. For those infants where hypothermia was discontinued in NICU our strategy facilitated re-warming. Re-adjustment to a lower target temperature to ≥34.5-<35.5°C may reduce the proportion of infants with high/normothermic temperatures.

Can 4-H/FCS Curricula and Program Activities Increase Self-Esteem in At-Risk Youth Ages 8-15?

Directory of Open Access Journals (Sweden)

Walter Barker

2010-03-01

Full Text Available Nationally 4-H programs develop educational strategies and provide opportunities for youth and adults to work in partnership as they develop life skills. This study looks at some curricula that enhance self-esteem in at-risk youth ages 8 to 15. The Coopersmith Self-Esteem Instrument (CSI measured changes in participants’ self-esteem while the Massachusetts Youth Screening Instrument (MAYSl, used only at the onset of the study, alert the staff of potential mental/emotional distress and other behavior that might require an immediate response. The CSI results showed increases in self-esteem. Girls showed a higher increase in self-esteem over the boys.

C-VAT – Clinical Video game Addiction Test: een diagnostisch instrument voor het herkennen van gameverslaving in de klinische praktijk.

OpenAIRE

Rooij, A.J. van; Duin, L. van; Frielink, N.; DeFuentes-Merillas, L.; Schoenmakers, T.M.

2012-01-01

In de Nederlandse verslavingszorg worden hulpverleners in toenemende mate geconfronteerd met een hulpvraag op het gebied van ‘gameverslaving’. Tot nu toe is er echter geen diagnostisch instrument dat gebruikt kan worden om het probleem goed in kaart te brengen. Dit artikel bespreekt de ontwikkeling van een dergelijk instrument, de Clinical Video game Addiction Test (C-VAT). De lijst bestaat uit drie introductievragen, negen kernvragen en aanbevelingen gericht op het ontdekken van comorbide pr...

Effects of Different End-Point Cooking Temperatures on the Efficiency of Encapsulated Phosphates on Lipid Oxidation Inhibition in Ground Meat.

Science.gov (United States)

Kılıç, B; Şimşek, A; Claus, J R; Atılgan, E; Aktaş, N

2015-10-01

Effects of 0.5% encapsulated (e) phosphates (sodium tripolyphosphate, STP; sodium hexametaphosphate, HMP; sodium pyrophosphate, SPP) on lipid oxidation during storage (0, 1, and 7 d) of ground meat (chicken, beef) after being cooked to 3 end-point cooking temperatures (EPCT; 71, 74, and 77 °C) were evaluated. The use of STP or eSTP resulted in lower (P cooking loss (CL) compared to encapsulated or unencapsulated forms of HMP and SPP. Increasing EPCT led to a significant increase in CL (P chicken compared to 74 and 71 °C (P chicken samples (P < 0.05). Findings suggest that encapsulated phosphates can be a strategy to inhibit lipid oxidation for meat industry and the efficiency of encapsulated phosphates on lipid oxidation inhibition can be enhanced by lowering EPCT. © 2015 Institute of Food Technologists®

40 CFR 35.137 - Application requirements.

Science.gov (United States)

2010-07-01

... ASSISTANCE STATE AND LOCAL ASSISTANCE Environmental Program Grants Performance Partnership Grants § 35.137... the environmental programs and the amount of funds from each program to be combined in the Performance... evaluation report required in § 35.125, and other environmental and programmatic data sources. (c) A State...

Radiative transfer in silylidene molecule

Directory of Open Access Journals (Sweden)

Sharma M.

2014-01-01

Full Text Available In order to search for silylidene (H2CSi in the interstellar medium, Izuha et al. (1996 recorded microwave spectrum of H2CSi in laboratory and made an unsuccessful attempt of its identification in IRC +10216, Ori KL, Sgr B2, through its 717-616 transition at 222.055 GHz. For finding out if there are other transitions of H2CSi which may help in its identification in the interstellar medium, we have considered 25 rotational levels of ortho-H2CSi connected by collisional transitions and 35 radiative transitions, and solved radiative transfer problem using the LVG approximation. We have found that the brightness temperatures of 919-818, 918-817, 101,10-919, 1019-918, 111,11-101,10, 111,10-1019 and 121,12-111,11 transition are larger than that of 717-616 transition. Thus, these transitions may help in detection of H2CSi in the interstellar medium.

Order in disorder

DEFF Research Database (Denmark)

Fraser, Hector W L; Nichol, Gary S; Uhrín, Dušan

2018-01-01

to all structures describes a centred hexagon with the MIII sites disordered around the outer wheel. The structural disorder has been characterised via single crystal X-ray crystallography, 1-3D 1H and 13C solution-state NMR spectroscopy of the diamagnetic analogue (4), and solid-state 27Al MAS NMR......A family of heterometallic Anderson-type 'wheels' of general formula [MIII2MII5(hmp)12](ClO4)4 (where MIII = Cr or Al and MII = Ni or Zn giving [Cr2Ni5] (1), [Cr2Zn5] (2), [Al2Ni5] (3) and [Al2Zn5] (4); hmpH = 2-pyridinemethanol) have been synthesised solvothermally. The metallic skeleton common...

Comparative transcriptomics with a motility-deficient mutant leads to identification of a novel polysaccharide secretion system in Nostoc punctiforme.

Science.gov (United States)

Risser, Douglas D; Meeks, John C

2013-02-01

Many filamentous cyanobacteria are capable of gliding motility by an undefined mechanism. Within the heterocyst-forming clades, some strains, such as the Nostoc spp. and Fisherella spp., are motile only as specialized filaments termed hormogonia. Here we report on the phenotype of inactivation of a methyl-accepting chemotaxis-like protein in Nostoc punctiforme, designated HmpD. The gene hmpD was found to be essential for hormogonium development, motility and polysaccharide secretion. Comparative global transcriptional profiling of the ΔhmpD strain demonstrated that HmpD has a profound effect on the transcriptional programme of hormogonium development, influencing approximately half of the genes differentially transcribed during differentiation. Utilizing this transcriptomic data, we identified a gene locus, designated here as hps, that appears to encode for a novel polysaccharide secretion system. Transcripts for the genes in the hps locus are upregulated in two steps, with the second step dependent on HmpD. Deletion of hpsA, hpsBCD or hpsEFG resulted in the complete loss of motility and polysaccharide secretion, similar to deletion of hmpD. Genes in the hps locus are highly conserved in the filamentous cyanobacteria, but generally absent in unicellular strains, implying a common mechanism of motility unique to the filamentous cyanobacteria. © 2012 Blackwell Publishing Ltd.

Bioaccumulation profiles of 35S-labelled sodium alkylpoly(oxyethylene) sulfates in carp (Cyprinus carpio)

International Nuclear Information System (INIS)

Kikuchi, M.; Wakabayashi, M.; Kojima, H.; Yoshida, T.

1980-01-01

The uptake, distribution and elimination of two labelled surfactants, 35 S-labelled sodium dodecyltri(oxyethylene) sulfate ( 35 S-C12-AES(3)) and 35 S-labelled sodium dodecylpenta(oxyethylene) sulfate ( 35 S-C12-AES(5)) were investigated in carp (Cyprinus carpio) exposed to concentrations of 0.3-0.6 mg l -1 , using whole-body autoradiography and the liquid scintillation counting method. 35 S-Radioactivity was first rapidly absorbed by the gills and skin and transferred to other organs and tissues. After 24h-exposure, there was a comparatively high accumulation of 35 S-radioactivity in the gills, hepatopancreas, gall bladder, intestinal content, and nasal and oral cavity. The distribution patterns of 35 S-radioactivity derived from 35 S-C12-AES(3) and 35 S-C12-AES(5) in tissues and organs were similar. The whole-body concentration factors of 35 S-radioactivity in fish exposed to 35 SC12-AES(3) and 35 S-C12-AES(5) for 72 hr were 18 and 4.7, respectively. In surfactant-free water, the absorbed 35 S-radioactivity was eliminated more rapidly from the fish body exposed to 35 S-C12-AES(3) than 35 S-C12-AES(5). It was eliminated relatively fast from gills and hepatopancreas, but elimination from gall bladder was rather slow. (author)

42 CFR 35.35 - Unsalable articles.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Unsalable articles. 35.35 Section 35.35 Public... HOSPITAL AND STATION MANAGEMENT Disposition of Articles Produced by Patients § 35.35 Unsalable articles. Articles having no commercial value shall be stored, destroyed, or otherwise disposed of as the officer in...

Instrument Design of the Large Aperture Solar UV Visible and IR Observing Telescope (SUVIT) for the SOLAR-C Mission

Science.gov (United States)

Suematsu, Y.; Katsukawa, Y.; Shimizu, T.; Ichimoto, K.; Takeyama, N.

2012-12-01

We present an instrumental design of one major solar observation payload planned for the SOLAR-C mission: the Solar Ultra-violet Visible and near IR observing Telescope (SUVIT). The SUVIT is designed to provide high-angular-resolution investigation of the lower solar atmosphere, from the photosphere to the uppermost chromosphere, with enhanced spectroscopic and spectro-polarimetric capability in wide wavelength regions from 280 nm (Mg II h&k lines) to 1100 nm (He I 1083 nm line) with 1.5 m class aperture and filtergraphic and spectrographic instruments.

An XML-based framework for personalized health management.

Science.gov (United States)

Lee, Hiye-Ja; Park, Seung-Hun; Jeong, Byeong-Soo

2006-01-01

This paper proposes a framework for personalized health management. In this framework, XML technology is used for representing and managing the health information and knowledge. Major components of the framework are Health Management Prescription (HMP) Expert System and Health Information Repository. The HMP Expert System generates a HMP efficiently by using XML-based templates. Health Information Repository provides integrated health information and knowledge for personalized health management by using XML and relational database together.

Characterization of a clinical unit for digital radiography based on irradiation side sampling technology

Energy Technology Data Exchange (ETDEWEB)

Rivetti, Stefano [Fisica Medica, Ospedale di Sassuolo S.p.A., 41049 Sassuolo (Italy); Lanconelli, Nico [Alma Mater Studiorum, Physics Department, University of Bologna, 40127 Bologna (Italy); Bertolini, Marco; Nitrosi, Andrea [Medical Physics Unit, Azienda Ospedaliera ASMN, Istituto di Ricovero e Cura a Carattere Scientifico, 42123 Reggio Emilia (Italy); Burani, Aldo [Ospedale di Sassuolo S.p.A., 41049 Sassuolo (Italy)

2013-10-15

Purpose: A characterization of a clinical unit for digital radiography (FUJIFILM FDR D-EVO) is presented. This system is based on the irradiation side sampling (ISS) technology and can be equipped with two different scintillators: one traditional gadolinium-oxysulphide phosphor (GOS) and a needle structured cesium iodide (CsI) phosphor panel.Methods: The characterization was achieved in terms of response curve, modulation transfer function (MTF), noise power spectra (NPS), detective quantum efficiency (DQE), and psychophysical parameters (contrast-detail analysis with an automatic reading of CDRAD images). For both scintillation screens the authors accomplished the measurements with four standard beam conditions: RAQ3, RQA5, RQA7, and RQA9.Results: At the Nyquist frequency (3.33 lp/mm) the MTF is about 35% and 25% for CsI and GOS detectors, respectively. The CsI scintillator has better noise properties than the GOS screen in almost all the conditions. This is particularly true for low-energy beams, where the noise for the GOS system can go up to a factor 2 greater than that found for CsI. The DQE of the CsI detector reaches a peak of 60%, 60%, 58%, and 50% for the RQA3, RQA5, RQA7, and RQA9 beams, respectively, whereas for the GOS screen the maximum DQE is 40%, 44%, 44%, and 35%. The contrast-detail analysis confirms that in the majority of cases the CsI scintillator is able to provide improved outcomes to those obtained with the GOS screen.Conclusions: The limited diffusion of light produced by the ISS reading makes possible the achievement of very good spatial resolution. In fact, the MTF of the unit with the CsI panel is only slightly lower to that achieved with direct conversion detectors. The combination of very good spatial resolution, together with the good noise properties reached with the CsI screen, allows achieving DQE on average about 1.5 times greater than that obtained with GOS. In fact, the DQE of unit equipped with CsI is comparable to the best

HLA-C -35kb expression SNP is associated with differential control of β-HPV infection in squamous cell carcinoma cases and controls.

Directory of Open Access Journals (Sweden)

Karin A Vineretsky

Full Text Available A single nucleotide polymorphism (SNP 35 kb upstream of the HLA-C gene is associated with HLA-C expression, and the high expressing genotype (CC has been associated with HIV-I control. HLA-C is unique among the classical MHC class I molecules for its role in the control of viral infections and recognition of abnormal or missing self. This immunosurveillance is central to the pathogenesis of non-melanoma skin cancer (NMSC, and of squamous cell carcinoma (SCC in particular. While sun exposure is a major risk factor for these cancers, cutaneous infections with genus β-HPV have been implicated in the development of SCC. We hypothesized that the high expression HLA-C genotype is associated with β-HPV infections. Therefore, we investigated the association between β-HPV serology and the -35 kb SNP (rs9264942 in a population-based case-control study of 510 SCC cases and 608 controls. Among controls, the high expression -35 kb SNP genotype (CC reduced the likelihood of positive serology for multiple (≥2 β-HPV infections (OR = 0.49, 95% CI: 0.25-0.97, and β-HPV species 2 infection (OR = 0.43, 95% CI: 0.23-0.79. However, no association with β-HPV status was observed among SCC cases. Our findings suggest that underlying immunogenotype plays an important role in differential control of β-HPV in SCC cases and controls.

Investigating the chemical mist deposition technique for poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) on textured crystalline-silicon for organic/crystalline-silicon heterojunction solar cells

Science.gov (United States)

Hossain, Jaker; Ohki, Tatsuya; Ichikawa, Koki; Fujiyama, Kazuhiko; Ueno, Keiji; Fujii, Yasuhiko; Hanajiri, Tatsuro; Shirai, Hajime

2016-03-01

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated in terms of cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature Ts, and substrate dc bias Vs as variables for efficient PEDOT:PSS/crystalline silicon (c-Si) heterojunction solar cells. The high-speed-camera and differential mobility analysis characterizations revealed that the average size and flux of PEDOT:PSS mist depend on f, type of solvent, and Vs. Film deposition occurred when positive Vs was applied to the c-Si substrate at Ts of 30-40 °C, whereas no deposition of films occurred with negative Vs, implying that the film is deposited mainly from negatively charged mist. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrates by adjusting Ts and Vs. The adhesion of CMD PEDOT:PSS film to c-Si was greatly enhanced by applying substrate dc bias Vs compared with that of spin-coated film. The CMD PEDOT:PSS/c-Si heterojunction solar cell devices on textured c-Si(100) in 2 × 2 cm2 exhibited a power conversion efficiency η of 11.0% with better uniformity of the solar cell parameters. Furthermore, η was increased to 12.5% by adding an AR coating layer of molybdenum oxide MoOx formed by CMD. These findings suggest that CMD with negatively charged mist has great potential for the uniform deposition of organic and inorganic materials on textured c-Si substrates by suitably adjusting Ts and Vs.

Digital study of nuclear reactor instrument

International Nuclear Information System (INIS)

Lv Gongxiang; Yang Zhijun

2006-01-01

The paper introduces the design method of nuclear reactor's digital instrument developed by authors based on the AT89C52 single chip microcomputer. Also the instrument system hardware structure and software framework are given. The instrument apply DDC112 which is responsible for the measure of lower current. When designing the instrument system, anti-interference measure of software, especially hardware is considered seriously. (authors)

Posterior Rigid Instrumentation of C7: Surgical Considerations and Biomechanics at the Cervicothoracic Junction. A Review of the Literature.

Science.gov (United States)

Bayoumi, Ahmed B; Efe, Ibrahim E; Berk, Selim; Kasper, Ekkehard M; Toktas, Zafer Orkun; Konya, Deniz

2018-03-01

The cervicothoracic junction is a challenging anatomic transition in spine surgery. It is commonly affected by different types of diseases that may significantly impair stability in this region. The seventh cervical vertebra (C7) is an atypical cervical vertebra with unique anatomic features compared to subaxial cervical spine (C3 to C6). C7 has relatively broader laminae, larger pedicles, smaller lateral masses, and a long nonbifid spinous process. These features allow a variety of surgical methods for performing posterior rigid instrumentation in the form of different types of screws, such as lateral mass screws, pedicle screws, transfacet screws, and intralaminar screws. Many biomechanical studies on cadavers have evaluated and compared different types of implants at C7. We reviewed PubMed/Medline by using specific combinations of keywords to summarize previously published articles that examined C7 posterior rigid instrumentation thoroughly in an experimental fashion on patients or cadavers with additional descriptive radiologic parameters for evaluation of the optimum surgical technique for each type. A total of 44 articles were reported, including 22 articles that discussed anatomic considerations (entry points, sagittal and axial trajectories, and features of screws) and another 22 articles that discussed the relevant biomechanical testing at this transitional region if C7 was directly involved in terms of receiving posterior rigid implants. C7 can accommodate different types of screws, which can provide additional benefits and risks based on availability of bony purchase, awareness of surgical technique, biomechanics, and anatomic considerations. Copyright © 2017 Elsevier Inc. All rights reserved.

A proposal for assessing study quality: Biomonitoring, Environmental Epidemiology, and Short-lived Chemicals (BEES-C) instrument

Science.gov (United States)

LaKind, Judy S.; Sobus, Jon R.; Goodman, Michael; Barr, Dana Boyd; Fürst, Peter; Albertini, Richard J.; Arbuckle, Tye E.; Schoeters, Greet; Tan, Yu-Mei; Teeguarden, Justin; Tornero-Velez, Rogelio; Weisel, Clifford P.

2015-01-01

The quality of exposure assessment is a major determinant of the overall quality of any environmental epidemiology study. The use of biomonitoring as a tool for assessing exposure to ubiquitous chemicals with short physiologic half-lives began relatively recently. These chemicals present several challenges, including their presence in analytical laboratories and sampling equipment, difficulty in establishing temporal order in cross-sectional studies, short- and long-term variability in exposures and biomarker concentrations, and a paucity of information on the number of measurements required for proper exposure classification. To date, the scientific community has not developed a set of systematic guidelines for designing, implementing and interpreting studies of short-lived chemicals that use biomonitoring as the exposure metric or for evaluating the quality of this type of research for WOE assessments or for peer review of grants or publications. We describe key issues that affect epidemiology studies using biomonitoring data on short-lived chemicals and propose a systematic instrument – the Biomonitoring, Environmental Epidemiology, and Short-lived Chemicals (BEES-C) instrument – for evaluating the quality of research proposals and studies that incorporate biomonitoring data on short-lived chemicals. Quality criteria for three areas considered fundamental to the evaluation of epidemiology studies that include biological measurements of short-lived chemicals are described: 1) biomarker selection and measurement, 2) study design and execution, and 3) general epidemiological study design considerations. We recognize that the development of an evaluative tool such as BEES-C is neither simple nor non-controversial. We hope and anticipate that the instrument will initiate further discussion/debate on this topic. PMID:25137624

Biological fermentative hydrogen production from olive pulp at 35 degrees C

Energy Technology Data Exchange (ETDEWEB)

Koutrouli, E.C.; Gavala, H.N.; Skiadas, I.V.; Lyberatos, G. [Patras Univ., Patras (Greece). Dept. of Chemical Engineering

2004-07-01

In response to energy security and environmental concerns, there is renewed interest in the use of hydrogen gas as a renewable energy source. However, many processes for generating hydrogen are extremely energy intensive and costly. This study focused on biological production of hydrogen from wastewater or other biomass. Photosynthetic and fermentation processes were outlined, but the main focus of this paper was on continuous anaerobic fermentation of low cost substrates such as olive pulp at 35 degrees C. This process is linked to the acidogenic stage of anaerobic digestion where carbohydrates are the preferred carbon source. Volatile fatty acids and alcohols are produced simultaneously with the hydrogen gas. An added advantage is that the effluent from the fermentation process can be further used by methanogenesis due to its rich organic acids content. Batch experiments with olive pulp resulted in 2.5 mmole of hydrogen per gram of total carbohydrates. It was noted that more research is required to maximize hydrogen production in a continuous process. It was suggested that hydrogen production could be optimized through hydrolysis of the non-soluble carbohydrates. This could be accomplished through physicochemical or biological pretreatments. 7 refs., 3 tabs., 1 fig.

Suzaku Diagnostics of the Energetics in the Lobes of the Giant Radio Galaxy 3C 35

Science.gov (United States)

Isobe, Naoki; Seta, Hiromi; Gandhi, Poshak; Tashiro, Makoto S.

2011-02-01

The Suzaku observation of a giant radio galaxy 3C 35 revealed faint extended X-ray emission, associated with its radio lobes and/or host galaxy. After careful subtraction of the X-ray and non-X-ray background and contaminating X-ray sources, the X-ray spectrum of the faint emission was reproduced by a sum of the power-law (PL) and soft thermal components. The soft component was attributed to the thermal plasma emission from the host galaxy. The photon index of the PL component, Γ = 1.35+0.56 -0.86 +0.11 -0.10, where the first and second errors represent the statistical and systematic ones, was found to agree with the synchrotron radio index from the lobes, ΓR = 1.7. Thus, the PL component was attributed to the inverse Compton (IC) X-rays from the synchrotron electrons in the lobes. The X-ray flux density at 1 keV was derived as 13.6 ± 5.4+4.0 -3.6 nJy with the photon index fixed at the radio value. The X-ray surface brightness from these lobes (~0.2 nJy arcmin-2) is lowest among the lobes studied through the IC X-ray emission. In combination with the synchrotron radio flux density, 7.5 ± 0.2 Jy at 327.4 MHz, the electron energy density spatially averaged over the lobes was evaluated to be the lowest among those radio galaxies, as u e = (5.8 ± 2.3+1.9 -1.7) × 10-14 erg cm-3 over the electron Lorentz factor of 103-105. The magnetic energy density was calculated as u m = (3.1+2.5 -1.0 +1.4 -0.9) × 10-14 erg cm-3, corresponding to the magnetic field strength of 0.88+0.31 -0.16 +0.19 -0.14 μG. These results suggest that the energetics in the 3C 35 lobes are nearly consistent with equipartition between the electrons and magnetic fields.

Supplemental Environmental Impact Statement for F-35 Beddown at Eglin Air Force Base, Florida

Science.gov (United States)

2014-06-26

IFR instrument flight rules IJTS Initial Joint Training Site ILLUM Illuminating ILS Instrument Landing System IMPLAN an economic impact modeling...Final Supplemental ENVIRONMENTAL IMPACT STATEMENT FOR F-35 BEDDOWN AT EGLIN AIR FORCE BASE, FLORIDA JANUARY 2014 Report Documentation Page Form...Supplemental Environmental Impact Statement 3. DATES COVERED 00-00-2011 to 00-00-2014 4. TITLE AND SUBTITLE Final Supplemental Environmental Impact

Cyclic 3',5'-adenosine monophosphate (cAMP) signaling in the anterior pituitary gland in health and disease.

Science.gov (United States)

Hernández-Ramírez, Laura C; Trivellin, Giampaolo; Stratakis, Constantine A

2018-03-05

The cyclic 3',5'-adenosine monophosphate (cAMP) was the first among the so-called "second messengers" to be described. It is conserved in most organisms and functions as a signal transducer by mediating the intracellular effects of multiple hormones and neurotransmitters. In this review, we first delineate how different members of the cAMP pathway ensure its correct compartmentalization and activity, mediate the terminal intracellular effects, and allow the crosstalk with other signaling pathways. We then focus on the pituitary gland, where cAMP exerts a crucial function by controlling the responsiveness of the cells to hypothalamic hormones, neurotransmitters and peripheral factors. We discuss the most relevant physiological functions mediated by cAMP in the different pituitary cell types, and summarize the defects affecting this pathway that have been reported in the literature. We finally discuss how a deregulated cAMP pathway is involved in the pathogenesis of pituitary disorders and how it affects the response to therapy. Copyright © 2017. Published by Elsevier B.V.

Early development of spinodal decomposition in neutron-irradiated Fe-35.5Ni-7.5Cr at 5500C

International Nuclear Information System (INIS)

Brager, H.R.; Garner, F.A.

1985-04-01

In Fe-35Ni-7.5Cr irradiated at 550 0 C to 2.5 x 10 22 n/cm 2 (E > 0.1 MeV) the spinodal decomposition observed at higher irradiation temperatures and higher neutron exposures is just beginning to form. The decomposition appears to begin very heterogeneously and may be assisted by the action of the inverse Kirkendall mechanism operating at various microstructural sinks

Virtual instrumentation: a new approach for control and instrumentation - application in containment studies facility

International Nuclear Information System (INIS)

Gole, N.V.; Shanware, V.M.; Sebastian, A.; Subramaniam, K.

2001-01-01

PC based data-acquisition has emerged as a rapidly developing area particularly with respect to process instrumentation. Computer based data acquisition in process instrumentation combined with Supervisory Control and Data Acquisition (SCADA) software has introduced extensive possibilities with respect to formats for presentation of information. The concept of presenting data using any instrument format with the help of software tools to simulate the instrument on screen, needs to be understood, in order to be able to make use of its vast potential. The purpose of this paper is to present the significant features of the Virtual Instrumentation concept and discuss its application in the instrumentation and control system of containment studies facility (CSF). Factors involved in the development of the virtual instrumentation based I and C system for CSF are detailed and a functional overview of the system configuration is given. (author)

Mandolin Family Instruments

Science.gov (United States)

Cohen, David J.; Rossing, Thomas D.

The mandolin family of instruments consists of plucked chordophones, each having eight strings in four double courses. With the exception of the mandobass, the courses are tuned in intervals of fifths, as are the strings in violin family instruments. The soprano member of the family is the mandolin, tuned G3-D4-A4-E5. The alto member of the family is the mandola, tuned C3-G3-D4-A4. The mandola is usually referred to simply as the mandola in the USA, but is called the tenor mandola in Europe. The tenor member of the family is the octave mandolin, tuned G2-D3-A3-E4. It is referred to as the octave mandolin in the USA, and as the octave mandola in Europe. The baritone member of the family is the mandocello, or mandoloncello, tuned C2-G2-D3-A3. A variant of the mandocello not common in the USA is the five-course liuto moderno, or simply liuto, designed for solo repertoire. Its courses are tuned C2-G2-D3-A3-E4. A mandobass was also made by more than one manufacturer during the early twentieth century, though none are manufactured today. They were fretted instruments with single string courses tuned E1-A1-D2-G2. There are currently a few luthiers making piccolo mandolins, tuned C4-G4-D5-A5.

Upgrade the startup test instrumentation (ANMS) with innovated I and C system at the Dukovany WWER 440/213 units

International Nuclear Information System (INIS)

Kocek, V.

2005-01-01

The paper focuses on the innovation procedures of physics startup tests instrumentation used in Dukovany NPP (ANMS) connected with I and C system refurbishment of the Dukovany WWER 440/213 units. The following matters are further discussed in this paper: a) changes in ANMS design, whose has been carried out due to reflect the situation connected with I and C innovation; b) process of consistency checking during implementation stage; c) results of the physics startup tests with upgraded ANMS in 2005 (introduction of Gd2 fuel on Dukovany NPP) (Authors)

10 CFR 35.406 - Brachytherapy sources accountability.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Brachytherapy sources accountability. 35.406 Section 35....406 Brachytherapy sources accountability. (a) A licensee shall maintain accountability at all times... area. (c) A licensee shall maintain a record of the brachytherapy source accountability in accordance...

DC servo motor positioning with anti-windup implementation using C2000 ARM-Texas Instrument

Science.gov (United States)

Linggarjati, Jimmy

2017-12-01

One of the most important topics in control system is DC Motor. At this research, a positioning control system for a DC motor is investigated. Firstly, the DC Motor will be paramaterized to get the transfer function model, in order to be simulated in Matlab, and then implemented in a C2000-ARM microcontroller from TI (Texas Instrument). With this investigation, students in control system theory will be able to understand the importance of classical control theories, in relation to the real world implementation of the position control for the DC Motor, escpecially the importance of Anti-Windup technique in real-world implementation.

Fast determination of the current loss mechanisms in textured crystalline Si-based solar cells

Science.gov (United States)

Nakane, Akihiro; Fujimoto, Shohei; Fujiwara, Hiroyuki

2017-11-01

A quite general device analysis method that allows the direct evaluation of optical and recombination losses in crystalline silicon (c-Si)-based solar cells has been developed. By applying this technique, the current loss mechanisms of the state-of-the-art solar cells with ˜20% efficiencies have been revealed. In the established method, the optical and electrical losses are characterized from the analysis of an experimental external quantum efficiency (EQE) spectrum with very low computational cost. In particular, we have performed the EQE analyses of textured c-Si solar cells by employing the experimental reflectance spectra obtained directly from the actual devices while using flat optical models without any fitting parameters. We find that the developed method provides almost perfect fitting to EQE spectra reported for various textured c-Si solar cells, including c-Si heterojunction solar cells, a dopant-free c-Si solar cell with a MoOx layer, and an n-type passivated emitter with rear locally diffused solar cell. The modeling of the recombination loss further allows the extraction of the minority carrier diffusion length and surface recombination velocity from the EQE analysis. Based on the EQE analysis results, the current loss mechanisms in different types of c-Si solar cells are discussed.

The GLAST Large Area Telescope Detector Performance Monitoring

International Nuclear Information System (INIS)

Borgland, A.W.; Charles, E.; SLAC

2007-01-01

The Large Area Telescope (LAT) is one of two instruments on board the Gamma-ray Large Area Telescope (GLAST), the next generation high energy gamma-ray space telescope. The LAT contains sixteen identical towers in a four-by-four grid. Each tower contains a silicon-strip tracker and a CsI calorimeter that together will give the incident direction and energy of the pair-converting photon in the energy range 20 MeV - 300 GeV. In addition, the instrument is covered by a finely segmented Anti-Coincidence Detector (ACD) to reject charged particle background. Altogether, the LAT contains more than 864k channels in the trackers, 1536 CsI crystals and 97 ACD plastic scintillator tiles and ribbons. Here we detail some of the strategies and methods for how we are planning to monitor the instrument performance on orbit. It builds on the extensive experience gained from Integration and Test and Commissioning of the instrument on ground

Learning Team Breach of a Posted Barricade to Connect an Instrument to Power

Energy Technology Data Exchange (ETDEWEB)

Wilburn, Dianne Williams [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-04-19

On February 15, 2017, a DESHF-STO HPFC (health physics field coordinator) was asked by an NEN-1 employee if they could move an instrument, a radiation dosimetry system, from A166A to another lab at TA-35 Building 2. The HPFC walked the job down and discovered the instrument was connected to power. The instrument had not been connected to power previously. See photo 1. The instrument is located within an RCA (radiological control area). Entry to connect the instrument to power the instrument requires contacting RP. RP personnel had not been contacted as required as stated in the RCA posting.

Effect of mouthrinses with different active agents in the prevention of initial dental erosion.

Science.gov (United States)

de Oliveira, Tatiane Alexandre; Scaramucci, Tais; Nogueira, Fernando Neves; Simões, Alyne; Sobral, Maria Angela Pita

2015-01-01

Hydrochloric acid (HCl) from the gastric juice is the only source of intrinsic acid, which can reach the oral cavity in cases of gastroesophageal reflux or chronic vomiting, enhancing the risk of dental erosion. Compare the effects of mouthrinses with different active agents in the prevention of initial dental erosion caused by HCl. Casein (CAS at 0.2%), sodium hexametaphosphate (HMP at 0.02%), titanium tetrafluoride (TiF4 at 0.34%), and stannous fluoride (SnF2 at 0.87%) were individually added to an experimental mouthrinse. The mouthrinse without additives was used as the negative control (C) and a commercially available mouthrinse for erosion (ELM-Elmex®) as the reference product. Enamel specimens were exposed to human saliva and randomly assigned to 6 experimental groups (n = 8). Specimens were submitted to erosion in HCl for 10 s, followed by to the experimental mouthrinses for 30 s, and artificial saliva for 60 min. This cycle was repeated 3 times. The total amounts of calcium and phosphorus released by the specimens in the 2nd and 3rd erosive challenges were evaluated by atomic emission spectrometry. Statistical analysis used Shapiro-Wilks and Hartley tests, followed by one-way ANOVA and Tukey tests. When compared with C, ELM and HMP presented significantly less calcium in solution, with no difference between them. All the groups showed similar and significantly less phosphorus than C, except CAS. HMP was the only agent that could match the protection against initial erosion of the commercially available mouthrinse in both analyses.

CSI: Dognapping workshop : an outreach experiment designed to produce students that are hooked on science.

Energy Technology Data Exchange (ETDEWEB)

Boyle, Timothy J.; Gorman, Anna K.; Pratt, Harry D., III; Hernandez-Sanchez, Bernadette A.; Lambert, Timothy N.; Ottley, Leigh Anna M.; Baros, Christina Marie

2008-04-01

The CSI: Dognapping Workshop is a culmination of the more than 65 Sandian staff and intern volunteers dedication to exciting and encouraging the next generation of scientific leaders. This 2 hour workshop used a 'theatrical play' and 'hands on' activities that was fun, exciting and challenging for 3rd-5th graders while meeting science curriculum standards. In addition, new pedagogical methods were developed in order to introduce nanotechnology to the public. Survey analysis indicated that the workshop had an overall improvement and positive impact on helping the students to understand concepts from materials science and chemistry as well as increased our interaction with the K-5 community. Anecdotal analyses showed that this simple exercise will have far reaching impact with the results necessary to maintain the United States as the scientific leader in the world. This experience led to the initiation of over 100 Official Junior Scientists.

3',5'-Cyclic diguanylic acid (c-di-GMP) inhibits basal and growth factor-stimulated human colon cancer cell proliferation

International Nuclear Information System (INIS)

Karaolis, David K.R.; Cheng, Kunrong; Lipsky, Michael; Elnabawi, Ahmed; Catalano, Jennifer; Hyodo, Mamoru; Hayakawa, Yoshihiro; Raufman, Jean-Pierre

2005-01-01

The novel cyclic dinucleotide, 3',5'-cyclic diguanylic acid, cGpGp (c-di-GMP), is a naturally occurring small molecule that regulates important signaling mechanisms in prokaryotes. Recently, we showed that c-di-GMP has 'drug-like' properties and that c-di-GMP treatment might be a useful antimicrobial approach to attenuate the virulence and pathogenesis of Staphylococcus aureus and prevent or treat infection. In the present communication, we report that c-di-GMP (≤50 μM) has striking properties regarding inhibition of cancer cell proliferation in vitro. c-di-GMP inhibits both basal and growth factor (acetylcholine and epidermal growth factor)-induced cell proliferation of human colon cancer (H508) cells. Toxicity studies revealed that exposure of normal rat kidney cells and human neuroblastoma cells to c-di-GMP at biologically relevant doses showed no lethal cytotoxicity. Cyclic dinucleotides, such as c-di-GMP, represent an attractive and novel 'drug-platform technology' that can be used not only to develop new antimicrobial agents, but also to develop novel therapeutic agents to prevent or treat cancer

Recombination reduction at the c-Si/RCA oxide interface through Ar-H2 plasma treatment

Science.gov (United States)

Landheer, Kees; Bronsveld, Paula C. P.; Poulios, Ioannis; Tichelaar, Frans D.; Kaiser, Monja; Schropp, Ruud E. I.; Rath, Jatin K.

2017-02-01

An Ar-H2 plasma treatment was applied on an ultrathin RCA oxide to create well-passivated silicon wafers with symmetric c-Si/SiOx:H/a-Si:H passivation layer stacks. The effective lifetime of these samples increased from 10 μs to 4 ms after annealing at 200 °C through Ar-H2 plasma treatment of the oxide. The results indicate that the plasma treatment can modify the RCA oxide and this enables atomic hydrogen diffusion at low annealing temperature, leading to a well passivated c-Si/SiOx:H interface. This might provide new possibilities to use wet chemical oxides in c-Si solar cells, for example as tunnel contacts.

MathWorks Simulink and C++ integration with the new VLT PLC-based standard development platform for instrument control systems

Science.gov (United States)

Kiekebusch, Mario J.; Di Lieto, Nicola; Sandrock, Stefan; Popovic, Dan; Chiozzi, Gianluca

2014-07-01

ESO is in the process of implementing a new development platform, based on PLCs, for upcoming VLT control systems (new instruments and refurbishing of existing systems to manage obsolescence issues). In this context, we have evaluated the integration and reuse of existing C++ libraries and Simulink models into the real-time environment of BECKHOFF Embedded PCs using the capabilities of the latest version of TwinCAT software and MathWorks Embedded Coder. While doing so the aim was to minimize the impact of the new platform by adopting fully tested solutions implemented in C++. This allows us to reuse the in house expertise, as well as extending the normal capabilities of the traditional PLC programming environments. We present the progress of this work and its application in two concrete cases: 1) field rotation compensation for instrument tracking devices like derotators, 2) the ESO standard axis controller (ESTAC), a generic model-based controller implemented in Simulink and used for the control of telescope main axes.

Alat Monitoring Suhu Melalui Aplikasi Android Menggunakan Sensor LM35 dan Modul SIM800L Berbasis Mikrokontroler ATMega16

Directory of Open Access Journals (Sweden)

I Kadek Agus Sara Sawita

2017-10-01

Full Text Available It has been successfully designed a temperature monitoring instrument through android application using LM35 sensor and SIM800L module based on ATMega16 microcontroller. The temperature is measured using a LM35 sensor which produces a voltage and sent to ADC. Microcontroller ATMega16 is using as the main processor of this monitoring instrument to calculate the program, so that analog data in the form of input voltage are converted into digital data form a measurable temperature. The measurable temperature is sent and saved in the database on the server computer using the SIM800L module so it can be displayed on the website. The website pages are accessed with android programs that installed on the smartphone so that measurable temperature data can be monitored using a smartphone. The measurable temperature results can be displayed on a 2x16-character LCD in the instrument designed. Compatibility of monitoring instrument with comparison instrument is 99,97 %.

Monte-Carlo simulations of secondary electron emission from CsI, induced by 1-10 keV X-rays and electrons

International Nuclear Information System (INIS)

Akkerman, A.; Gibrekhterman, A.; Breskin, A.; Chechik, R.

1992-05-01

A model for electron transport and emission in CsI is proposed. It is based on theoretically calculated microscopic cross-sections for electron interaction with the nuclear and the electronic components of the solid. A Monte Carlo program based on this model was developed to simulate secondary electron emission induced by X-rays and electrons in the energy range of 1 to 10 keV. The calculated secondary emission yields agree with existing experimental data. The model provides all necessary characteristics for the design of radiation detectors based on secondary electron emission. It can be expanded to higher incident energies and other alkali halides. (author)

A compact and modular x- and gamma-ray detector with a CsI scintillator and double-readout Silicon Drift Detectors

Science.gov (United States)

Campana, R.; Fuschino, F.; Labanti, C.; Marisaldi, M.; Amati, L.; Fiorini, M.; Uslenghi, M.; Baldazzi, G.; Bellutti, P.; Evangelista, Y.; Elmi, I.; Feroci, M.; Ficorella, F.; Frontera, F.; Picciotto, A.; Piemonte, C.; Rachevski, A.; Rashevskaya, I.; Rignanese, L. P.; Vacchi, A.; Zampa, G.; Zampa, N.; Zorzi, N.

2016-07-01

A future compact and modular X and gamma-ray spectrometer (XGS) has been designed and a series of proto- types have been developed and tested. The experiment envisages the use of CsI scintillator bars read out at both ends by single-cell 25 mm2 Silicon Drift Detectors. Digital algorithms are used to discriminate between events absorbed in the Silicon layer (lower energy X rays) and events absorbed in the scintillator crystal (higher energy X rays and -rays). The prototype characterization is shown and the modular design for future experiments with possible astrophysical applications (e.g. for the THESEUS mission proposed for the ESA M5 call) are discussed.

Strange particle production in anti pp annihilation from 1.22 to 1.35 GeV/c

International Nuclear Information System (INIS)

Handler, T.; Plano, R.J.; Brucker, E.B.; Koller, E.L.; Taylor, S.; Stamer, P.E.

1976-01-01

Experimental results on antiproton-proton annihilations at 5 incident momenta in the range 1.22-1.35 GeV/c into final states with at least one visible K 1 0 meson are presented. Based on a total of 5855 events, cross sections and resonance fractions for all experimentally accessible final states are determined. The total cross section for annihilation into strange particles with at least one visible K 1 0 is 2069 +- 45 μb. Copious resonance production is observed but there is no significant evidence for the formation of a resonance in the s-channel. (Auth.)

40 CFR 35.1605-1 - The Act.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false The Act. 35.1605-1 Section 35.1605-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL... The Act. The Clean Water Act, as amended (33 U.S.C. 1251 et seq.). ...

Hepatic steatosis assessment with {sup 1}H-spectroscopy and chemical shift imaging at 3.0 T before hepatic surgery: Reliable enough for making clinical decisions?

Energy Technology Data Exchange (ETDEWEB)

Koelblinger, Claus, E-mail: claus.koelblinger@meduniwien.ac.at [Department of Radiology, Medical University of Vienna (Austria); Krssak, Martin, E-mail: martin.krssak@meduniwien.ac.at [Department of Radiology, Medical University of Vienna (Austria); Maresch, Judith, E-mail: judith.maresch@meduniwien.ac.at [Department of Pathology, Medical University of Vienna (Austria); Wrba, Fritz, E-mail: fritz.wrba@meduniwien.ac.at [Department of Pathology, Medical University of Vienna (Austria); Kaczirek, Klaus, E-mail: klaus.kaczirek@meduniwien.ac.at [Department of Surgery, Medical University of Vienna (Austria); Gruenberger, Thomas, E-mail: thomas.gruenberger@meduniwien.ac.at [Department of Surgery, Medical University of Vienna (Austria); Tamandl, Dietmar, E-mail: dietmar.tamandl@meduniwien.ac.at [Department of Surgery, Medical University of Vienna (Austria); Ba-Ssalamah, Ahmed, E-mail: ahmed.ba-ssalamah@meduniwien.ac.at [Department of Radiology, Medical University of Vienna (Austria); Berger-Kulemann, Vanessa, E-mail: vanessa.berger-kulemann@meduniwien.ac.at [Department of Radiology, Medical University of Vienna (Austria); Weber, Michael, E-mail: michael.weber@meduniwien.ac.at [Department of Radiology, Medical University of Vienna (Austria); Schima, Wolfgang, E-mail: wolfgang.schima@khgh.at [Department of Radiology, KH Goettlicher Heiland and Herz-Jesu Krankenhaus, Dornbacher Strasse 20-28, 1170 Vienna (Austria)

2012-11-15

Purpose: To compare the accuracy of liver fat quantification using chemical shift imaging (CSI) and H1 MR-spectroscopy (MRS) at 3.0 T in patients undergoing liver resection. Methods: Totally 35 patients were included in this prospective IRB approved study. The histopathologically assessed liver fat was compared to the hepatic fat fractions calculated with CSI (with and without spleen correction) and MRS. Spearman's rank correlation and Fisher z-test were used for correlation analysis. Sensitivity and specificity regarding the detection of marked steatosis were calculated for the different modalities and compared using the McNemar test. Results: MRS (r = .85) and CSI with spleen correction (r = .85) showed a significantly better correlation (p = .03) with histology compared to CSI without spleen correction (r = .67). Sensitivity and specificity for the detection of marked steatosis was 100% (12/12) and 87% (20/23) for MRS and 92% (11/12) and 83% (19/23) for CSI with spleen correction (p > .12). Conclusion: For the assessment of hepatic steatosis both CSI with spleen correction and MRS at 3.0 T, show a good correlation with histology. CSI without spleen correction should not be used. Sensitivity and specificity for the detection of marked steatosis are high with both modalities. However, results that are scattered around the cut-off values are not reliable enough for clinical decisions.

Training With Curved Laparoscopic Instruments in Single-Port Setting Improves Performance Using Straight Instruments: A Prospective Randomized Simulation Study.

Science.gov (United States)

Lukovich, Peter; Sionov, Valery Ben; Kakucs, Timea

2016-01-01

Lately single-port surgery is becoming a widespread procedure, but it is more difficult than conventional laparoscopy owing to the lack of triangulation. Although, these operations are also possible with standard laparoscopic instruments, curved instruments are being developed. The aims of the study were to identify the effect of training on a box trainer in single-port setting on the quality of acquired skills, and transferred with the straight and curved instruments for the basic laparoscopic tasks, and highlight the importance of a special laparoscopic training curriculum. A prospective study on a box trainer in single-port setting was conducted using 2 groups. Each group performed 2 tasks on the box trainer in single-port setting. Group-S used conventional straight laparoscopic instruments, and Group-C used curved laparoscopic instruments. Learning curves were obtained by daily measurements recorded in 7-day sessions. On the last day, the 2 groups changed instruments between each other. 1st Department of Surgery, Semmelweis University of Medicine from Budapest, Hungary, a university teaching hospital. In all, 20 fifth-year medical students were randomized into 2 groups. None of them had any laparoscopic or endoscopic experience. Participation was voluntary. Although Group-S performed all tasks significantly faster than Group-C on the first day, the difference proved to be nonsignificant on the last day. All participants achieved significantly shorter task completion time on the last day than on the first day, regardless of the instrument they used. Group-S showed improvement of 63.5%, and Group-C 69.0% improvement by the end of the session. After swapping the instruments, Group-S reached significantly higher task completion time with curved instruments, whereas Group-C showed further progression of 8.9% with straight instruments. Training with curved instruments in a single-port setting allows for a better acquisition of skills in a shorter period. For this

Optical Performance of Breadboard Amon-Ra Imaging Channel Instrument for Deep Space Albedo Measurement

Directory of Open Access Journals (Sweden)

Won Hyun Park

2007-03-01

Full Text Available The AmonRa instrument, the primary payload of the international EARTHSHINE mission, is designed for measurement of deep space albedo from L1 halo orbit. We report the optical design, tolerance analysis and the optical performance of the breadborad AmonRa imaging channel instrument optimized for the mission science requirements. In particular, an advanced wavefront feedback process control technique was used for the instrumentation process including part fabrication, system alignment and integration. The measured performances for the complete breadboard system are the RMS 0.091 wave(test wavelength: 632.8 nm in wavefront error, the ensquared energy of 61.7%(in 14 μ m and the MTF of 35.3%(Nyquist frequency: 35.7 mm^{-1} at the center field. These resulting optical system performances prove that the breadboard AmonRa instrument, as built, satisfies the science requirements of the EARTHSHINE mission.

Fatigue testing of controlled memory wire nickel-titanium rotary instruments.

Science.gov (United States)

Shen, Ya; Qian, Wei; Abtin, Houman; Gao, Yuan; Haapasalo, Markus

2011-07-01

To improve the fracture resistance of nickel-titanium (NiTi) files, manufacturers have introduced new alloys to manufacture NiTi files and developed new manufacturing processes. This study was aimed to examine the fatigue behavior of NiTi instruments from a novel controlled memory NiTi wire (CM Wire). Instruments of ProFile, Typhoon (TYP), Typhoon CM (TYP CM), DS-SS0250425NEYY (NEYY), and DS-SS0250425NEYY CM (NEYY CM) (DS Dental, Johnson City, TN) all size 25/.04 were subjected to rotational bending at the curvature of 35° and 45° in air at the temperature of 23° ± 2°C, and the number of revolutions to fracture (N(f)) was recorded. The fracture surface of all fragments was examined by a scanning electron microscope. The crack-initiation sites, the percentage of dimple area to the whole fracture cross-section, and the surface strain amplitude (ε(a)) were noted. The new alloy yielded an improvement of over three to eight times in N(f) of CM files than that of conventional NiTi files (P wire (58%-100%) had one crack origin. The values of the fraction area occupied by the dimple region were significantly smaller on CM NiTi instruments compared with conventional NiTi instruments (P wire at both curvatures (P Wire had a significantly higher N(f) and lower surface strain amplitude than the conventional NiTi wire files with identical design. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Precision and accuracy of blood glucose measurements using three different instruments.

Science.gov (United States)

Nowotny, B; Nowotny, P J; Strassburger, K; Roden, M

2012-02-01

Assessment of insulin sensitivity by dynamic metabolic tests such as the hyperinsulinemic euglycemic clamp critically relies on the reproducible and fast measurement of blood glucose concentrations. Although various instruments have been developed over the last decades, little is known as to the accuracy and comparability. We therefore compared the best new instrument with the former gold standard instruments to measure glucose concentrations in metabolic tests. Fasting blood samples of 15 diabetic and 10 healthy subjects were collected into sodium-fluoride tubes, spiked with glucose (0, 2.8, 6.9 and 11.1 mmol/l) and measured either as whole blood (range 3.3-26.3 mmol/l) or following centrifugation as plasma (range 3.9-32.0 mmol/l). Plasma samples were analyzed in the YSI-2300 STAT plus (YSI), EKF Biosen C-Line (EKF) and the reference method, Beckman Glucose analyzer-II (BMG), whole blood samples in EKF instruments with YSI as reference method. The average deviation of the EKF from the reference, BMG, was 3.0 ± 3.5% without any concentration-dependent variability. Glucose measurements by YSI were in good agreement with that by BMG (plasma) and EKF (plasma and whole blood) up to concentrations of 13.13 mmol/l (0.5 ± 3.7%), but deviation increased to -6.2 ± 3.8% at higher concentrations. Precision (n = 6) was ±2.2% (YSI), ±3.9% (EKF) and ±5.2% (BMG). The EKF instrument is comparable regarding accuracy and precision to the reference method BMG and can be used in metabolic tests, while the YSI showed a systematic shift at higher glucose concentrations. Based on these results we decided to replace BMG with EKF instrument in metabolic tests. © 2012 The Authors. Diabetic Medicine © 2012 Diabetes UK.

The reliability and validity of Cognitive Abilities Screening Instrument C-2.0 in Screening elderly people in Chengdu

Institute of Scientific and Technical Information of China (English)

Luo Zhuming; Lu Rong

2000-01-01

Background: Cognitive Abilities Screening Instrument C-2.0 (CASI C-2.0) is founded on Chinese culture apply to person with little or no formal education.Objective: In order to assess the reliability and validity of Cognitive Abilities Screening Instrument C-2.0 (CASI C-2.0), we surveyed 807 persons aged from 55 to 100 years and with little or no formal education in the town and country of Chengdu city. Methods: Phase I: 807 persona were assessed by different doctors with CASI C-2.0 and Mini mental State Examination (MMSE). Phase Ⅱ: The positive persons of phase I were assessed by trained field physicians who did not know the CASI C-2.0 and MMSE scores. The physicians assessment included a detail history, a systematic physical examination and a selected group of psychometric tests to ascertain the clinical diagnoses of dementia、 Alzheimer′s disease and vascular dementia utilizing the ICD-10 and NINCDS-ADRAD、 DSM-Ⅳ criteria respectively. Phase Ⅲ: 30 persons were retest with CASI C-2.0 randomly after 3--4 weeks. Results: Among the 807 persons, 55 cases of dementia were identified, including 50 cases of probable Alzheimer′s disease and 5 cases of vascular dementia. Discussion: On reliability, the test-retest reliability coefficient of CASI C-2.0 is 0.97,p＜0.001, the person′s correlation coefficient between nine items scores and total scores are all above 0.66, the Cronback a is 0.9056, the split-half reliability coefficient is 0.8355. On validity, using ICD-10 criteria as ”Gold Criteria" and 50 as a cut-offscore, the sensitivity、 specificity、 accuracy of CASI C-2.0 are 94.5%、 89.5%、 89.8% respectively, kappa is 0.5123. Comparing with MMSE, CAS1 C-2.0 has a better specificity, x2 test, p＜0.01; a same sensitivity; and a lower refusal answer ratio, x2 test, p＜0.005. Conclusion: We consider that CASI C-2.0 has excellent reliability and validity. It is worthy of disseminating and applying for both clinical and epidemiological surveys.

AUDIT and AUDIT-C as screening instruments for alcohol problem use in adolescents.

Science.gov (United States)

Liskola, Joni; Haravuori, Henna; Lindberg, Nina; Niemelä, Solja; Karlsson, Linnea; Kiviruusu, Olli; Marttunen, Mauri

2018-07-01

The Alcohol Use Disorders Identification Test (AUDIT) is commonly used in adults to screen for harmful alcohol consumption but few studies exist on its use among adolescents. Our aim was to validate the AUDIT and its derivative consumption questionnaire (AUDIT-C) as screening instruments for the detection of problem use of alcohol in adolescents. 621 adolescents (age-range, 12-19 years) were drawn from clinical and population samples who completed the AUDIT questionnaire. Psychiatric diagnoses were assessed using K-SADS-PL. A rating based on the K-SADS-PL was used to assess alcohol use habits, alcohol use disorders, screening and symptom criteria questions. Screening performance of the AUDIT and AUDIT-C sum scores and Receiver Operating Characteristic (ROC) curves were calculated. The diagnostic odds ratios (dOR) were calculated to express the overall discrimination between cut-offs. Comparisons of ROC between the AUDIT and AUDIT-C pairs indicated a slightly better test performance by AUDIT for the whole sample and in a proportion of the subsamples. Optimal cut-off value for the AUDIT was ≥5 (sensitivity 0.931, specificity 0.772, dOR 45.22; 95% CI: 24.72-83.57) for detecting alcohol problem use. The corresponding optimal cut-off value for the AUDIT-C was ≥3 in detecting alcohol problem use (sensitivity 0.952, specificity 0.663, dOR 39.31; 95% CI: 19.46-78.97). Agreement between the AUDIT and AUDIT-C using these cut-off scores was high at 91.9%. Our results for the cut-off scores for the early detection of alcohol problem use in adolescents are ≥5 for AUDIT, and ≥3 for AUDIT-C. Copyright © 2018 Elsevier B.V. All rights reserved.

Hypothermic machine perfusion reduces delayed graft function and improves one-year graft survival of kidneys from expanded criteria donors: a meta-analysis.

Directory of Open Access Journals (Sweden)

Baoping Jiao

Full Text Available BACKGROUND: Expanded criteria donors (ECDs are currently accepted as potential sources to increase the donor pool and to provide more chances of kidney transplantation for elderly recipients who would not survive long waiting periods. Hypothermic machine perfusion (HMP is designed to mitigate the deleterious effects of simple cold storage (CS on the quality of preserved organs, particularly when the donor is in a marginal status. METHODS: We compared the transplant outcomes in patients receiving ECD kidneys with either HMP or CS graft preservation. Articles from the MEDLINE, EMBASE and Cochrane Library databases were searched and all studies reporting outcomes from HMP versus CS methods of kidney preservation were included in this meta-analysis. The parameters analyzed included the incidence of delayed graft function (DGF, primary non-function (PNF and one-year graft and patient survival. RESULTS: A total of seven studies qualified for the review, involving 2374 and 8716 kidney grafts with HMP or CS preservation respectively, all from ECD donors. The incidence of delayed graft function (DGF was significantly reduced with an odd ratio(OR of 0.59 (95% CI 0.54-0.66, P<0.001 and one-year graft survival was significantly improved with an OR of 1.12 (95% CI 1.03-1.21, P = 0.005 in HMP preservation compared to CS. However, there was no difference in the incidence of PNF (OR 0.54, 95% CI 0.21-1.40, P = 0.20, and one-year patient survival (OR 0.98, 95% CI 0.94-1.02, P = 0.36 between HMP and CS preservation. CONCLUSIONS: HMP was associated with a reduced incidence of DGF and an with increased one-year graft survival, but it was not associated with the incidence of PNF and one-year patient survival.

Simulated predictions for H I at z = 3.35 with the Ooty Wide Field Array - I. Instrument and the foregrounds

Science.gov (United States)

Marthi, Visweshwar Ram; Chatterjee, Suman; Chengalur, Jayaram N.; Bharadwaj, Somnath

2017-11-01

Foreground removal is the most important step in detecting the large-scale redshifted H I 21-cm signal. Modelling foreground spectra is challenging and is further complicated by the chromatic response of the telescope. We present a multifrequency angular power spectrum (MAPS) estimator for use in a survey for redshifted H I 21-cm emission from z ˜ 3.35 and demonstrate its ability to accurately characterize the foregrounds. This survey will be carried out with the two wide-field interferometer modes of the upgraded Ooty Radio Telescope, called the Ooty Wide Field Array (OWFA), at 326.5 MHz. We have tailored the two-visibility correlation for OWFA to estimate the MAPS and test it with simulated foregrounds. In the process, we describe a software model that encodes the geometry and the details of the telescope and simulates a realistic model for the bright radio sky. This article presents simulations that include the full chromatic response of the telescope in addition to the frequency dependence intrinsic to the foregrounds. We find that the visibility correlation MAPS estimator recovers the input angular power spectrum accurately and that the instrument response to the foregrounds dominates the systematic errors in the recovered foreground power spectra.

Measuring decision quality: psychometric evaluation of a new instrument for breast cancer surgery

Directory of Open Access Journals (Sweden)

Sepucha Karen R

2012-06-01

Full Text Available Abstract Background The purpose of this paper is to examine the acceptability, feasibility, reliability and validity of a new decision quality instrument that assesses the extent to which patients are informed and receive treatments that match their goals. Methods Cross-sectional mail survey of recent breast cancer survivors, providers and healthy controls and a retest survey of survivors. The decision quality instrument includes knowledge questions and a set of goals, and results in two scores: a breast cancer surgery knowledge score and a concordance score, which reflects the percentage of patients who received treatments that match their goals. Hypotheses related to acceptability, feasibility, discriminant validity, content validity, predictive validity and retest reliability of the survey instrument were examined. Results We had responses from 440 eligible patients, 88 providers and 35 healthy controls. The decision quality instrument was feasible to implement in this study, with low missing data. The knowledge score had good retest reliability (intraclass correlation coefficient = 0.70 and discriminated between providers and patients (mean difference 35%, p  Conclusions The decision quality instrument met the criteria of feasibility, reliability, discriminant and content validity in this sample. Additional research to examine performance of the instrument in prospective studies and more diverse populations is needed.

Dicty_cDB: AHA244 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available one) Pichia stipitis CBS 6054 chromos... 35 4.8 EU095850_1( EU095850 |pid:none) Turkey coronavirus isolate M...G10, c... 35 4.8 EU095850_2( EU095850 |pid:none) Turkey coronavirus isolate MG10, c... 35 4.8 CP000094_2730(

Threatened and Endangered Species Habitat Management Plan for Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Hathcock, Charles Dean [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Keller, David Charles [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Thompson, Brent E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-16

Los Alamos National Laboratory’s (LANL) Threatened and Endangered Species Habitat Management Plan (HMP) fulfills a commitment made to the U.S. Department of Energy (DOE) in the “Final Environmental Impact Statement for the Dual-Axis Radiographic Hydrodynamic Test Facility Mitigation Action Plan” (DOE 1996). The HMP received concurrence from the U.S. Fish and Wildlife Service (USFWS) in 1999 (USFWS consultation numbers 2-22-98-I-336 and 2-22-95-I-108). This 2017 update retains the management guidelines from the 1999 HMP for listed species, and updates some descriptive information.

Observation of apparent MOS regimes on Al/PECVD grown boron nitride/p-c-Si/Al MIS structure, investigated through admittance spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Oezdemir, Orhan [Yildiz Technical University, Department of Physics, Esenler, istanbul (Turkey)

2009-02-15

PECVD grown boron nitride (BN) on crystalline silicon (c-Si) semiconductor was investigated by admittance measurement in the form of metal/insulator/semiconductor (MIS) structure. Apart from well-known regimes of traditional MOS structure, gradual bypassing of depletion layer was observed once ambient temperature (frequency) increased (decreased). Such an anomalous behavior was interpreted through modulations of charges located within BN film and/or at the interfacial layer of BN film/c-Si junction in terms of weighted average concept. (author)

Development of High Quality 4H-SiC Thick Epitaxy for Reliable High Power Electronics Using Halogenated Precursors

Science.gov (United States)

2016-08-02

defects :=()llowed by a second buffer epilayer gro\\\\ th with ~: urn thickness with high n-type dopi:1g (- 5£17 cm-3) for the same C/Si ratio of ~1.4 at...gradient, pressure , etc.) can further reduce the parasitic deposition, especially in TFS-growth. • Thick epitaxy on-axis 4H-SiC Growth at High Growth...From - To) 08/02/2016 Final Technical Report 01-Apr-10 Through 31-Mar-14 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER Development of High Quality 4H

[Surgical instruments and the emblems of Alsatien craftsmen and the archives of Obernai (16th-17th centuries)].

Science.gov (United States)

Muller, Christine

2011-01-01

This study presents some original data concerning the instruments used by Alsatian surgeons-barbers from the 16th to the 18th century. Emblems of professions frequently appear on private houses in Alsace, and 35 emblems of surgeons-barbers have been discovered; six, particularly chararacteristic, are analysed here (Soultz 1568, Marlenheim 1581, Sainte-Croix-en-Plaine 1587, Rosheim 1681, Rosheim 1733, and Wasselonne 1738). The razor (Schermesser), the lancet (Lanzette), and the "flame" (Lasseisen, Fliete) are the most frequently represented instruments. Unpublished inventories after death also bring instructive data and in particular those of the barbers Hans Artz of Molsheim (1597) and Jacob Pflieger of Obernai (c. 1608-1609). At last, are evoked unpublished mentions concerning two barbers originating from Obernai who exercised in Eastern Europe (Sebald Korn around 1583, and Johannes Baur around 1637).

76 FR 5144 - Notice of Intent To Prepare an Environmental Impact Statement for U.S. Navy F-35C West Coast...

Science.gov (United States)

2011-01-28

... CONTACT: U.S. Navy F-35C West Coast Homebasing EIS Project Manager; Naval Facilities Engineering Command... (from January 28, 2011 through March 14, 2011). All comments will receive the same attention and... Facilities Engineering Command, Southwest (Code EV21/AK); 1220 Pacific Highway, Bldg. 1, San Diego, CA 92132...

Biophysical influence of coumarin 35 on bovine serum albumin: Spectroscopic study

Science.gov (United States)

Bayraktutan, Tuğba; Onganer, Yavuz

2017-01-01

The binding mechanism and protein-fluorescence probe interactions between bovine serum albumin (BSA) and coumarin 35 (C35) was investigated by using UV-Vis absorption and fluorescence spectroscopies since they remain major research topics in biophysics. The spectroscopic data indicated that a fluorescence quenching process for BSA-C35 system was occurred. The fluorescence quenching processes were analyzed using Stern-Volmer method. In this regard, Stern-Volmer quenching constants (KSV) and binding constants were calculated at different temperatures. The distance r between BSA (donor) and C35 (acceptor) was determined by exploiting fluorescence resonance energy transfer (FRET) method. Synchronous fluorescence spectra were also studied to observe information about conformational changes. Moreover, thermodynamics parameters were calculated for better understanding of interactions and conformational changes of the system.

Preparing Specialized Undergraduate Pilot Training Graduates for F-35A Training

Science.gov (United States)

2010-06-11

the two sides of this argument and analyze the new data acquired from an F-22A lead-in program and the fact that the F-35A has started flying with...flight operations under Instrument or Visual Flight Rules to include day / night IFR operations in the terminal and enroute environment. Have limited

14 CFR 35.17 - Materials and manufacturing methods.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Materials and manufacturing methods. 35.17... AIRWORTHINESS STANDARDS: PROPELLERS Design and Construction § 35.17 Materials and manufacturing methods. (a) The... and manufacturing methods must conform to specifications acceptable to the Administrator. (c) The...

The 2007 ESO Instrument Calibration Workshop

CERN Document Server

Kaufer, Andreas; ESO Workshop

2008-01-01

The 2007 ESO Instrument Calibration workshop brought together more than 120 participants with the objective to a) foster the sharing of information, experience and techniques between observers, instrument developers and instrument operation teams, b) review the actual precision and limitations of the applied instrument calibration plans, and c) collect the current and future requirements by the ESO users. These present proceedings include the majority of the workshop’s contributions and document the status quo of instrument calibration at ESO in large detail. Topics covered are: Optical Spectro-Imagers, Optical Multi-Object Spectrographs, NIR and MIR Spectro-Imagers, High-Resolution Spectrographs, Integral Field Spectrographs, Adaptive Optics Instruments, Polarimetric Instruments, Wide Field Imagers, Interferometric Instruments as well as other crucial aspects such as data flow, quality control, data reduction software and atmospheric effects. It was stated in the workshop that "calibration is a life-long l...

Fast magnetization tunneling in tetranickel(II) single-molecule magnets.

Science.gov (United States)

Yang, En-Che; Wernsdorfer, Wolfgang; Zakharov, Lev N; Karaki, Yoshitomo; Yamaguchi, Akira; Isidro, Rose M; Lu, Guo-Di; Wilson, Samuel A; Rheingold, Arnold L; Ishimoto, Hidehiko; Hendrickson, David N

2006-01-23

A series of Ni(4) cubane complexes with the composition [Ni(hmp)(ROH)Cl](4) complexes 1-4 where R= -CH(3) (complex 1), -CH(2)CH(3) (complex 2), -CH(2)CH(2)(C(4)H(9)) (complex 3), -CH(2)CH(2)CH(2)(C(6)H(11)) (complex 4), hmp(-) is the anion of 2-hydroxymethylpyridine, t-Buhmp(-) is the anion of 4-tert-butyl-2-hydroxymethylpyridine, and dmb is 3,3-dimethyl-1-butanol] and [Ni(hmp)(dmb)Br](4) (complex 5) and [Ni(t-Buhmp)(dmb)Cl](4) (complex 6) were prepared. All six complexes were characterized by dc magnetic susceptibility data to be ferromagnetically coupled to give an S = 4 ground state with significant magnetoanisotropy (D approximately equal to -0.6 cm(-1)). Magnetization hysteresis measurements carried out on single crystals of complexes 1-6 establish the single-molecule magnet (SMM) behavior of these complexes. The exchange bias observed in the magnetization hysteresis loops of complexes 1 and 2 is dramatically decreased to zero in complex 3, where the bulky dmb ligand is employed. Fast tunneling of magnetization is observed for the high-symmetry (S(4) site symmetry) Ni(4) complexes in the crystal of complex 3, and the tunneling rate can even be enhanced by destroying the S(4) site symmetry, as is the case for complex 4, where there are two crystallographically different Ni(4) molecules, one with C(2) and the other with C(1) site symmetry. Magnetic ordering temperatures due to intermolecular dipolar and magnetic exchange interactions were determined by means of very low-temperature ac susceptibility measurements; complex 1 orders at 1100 mK, complex 3 at 290 mK, complex 4 at approximately 80 mK, and complex 6 at lower temperatures for those complexes with the bulkiest ligands.

Proceedings of the spring meeting of the Study Group for Electronic Instrumentation on April 3-5, 1995 in Juelich

International Nuclear Information System (INIS)

1995-06-01

The 17 papers presented at the meeting give a survey of recent progress in the field of electronic instrumentation of scientific and technical measuring instruments, achieved at the research centers of KFA Juelich, TU Graz, HMI Berlin, Karlsruhe FZ, and Rossendorf FZ. (DG) [de

Electrical interface characteristics (I-V), optical time of flight measurements, and the x-ray (20 keV) signal response of amorphous-selenium/crystalline-silicon heterojunction structures

Science.gov (United States)

Hunter, David M.; Ho, Chu An; Belev, George; De Crescenzo, Giovanni; Kasap, Safa O.; Yaffe, Martin J.

2011-03-01

We have investigated the dark current, optical TOF (time of flight) properties, and the X-ray response of amorphousselenium (a-Se)/crystalline-silicon (c-Si) heterostructures for application in digital radiography. The structures have been studied to determine if an x-ray generated electron signal, created in an a-Se layer, could be directly transferred to a c-Si based readout device such as a back-thinned CCD (charge coupled device). A simple first order band-theory of the structure indicates that x-ray generated electrons should transfer from the a-Se to the c-Si, while hole transfer from p-doped c-Si to the a-Se should be blocked, permitting a low dark signal as required. The structures we have tested have a thin metal bias electrode on the x-ray facing side of the a-Se which is deposited on the c-Si substrate. The heterostructures made with pure a-Se deposited on epitaxial p-doped (5×10 14 cm-3) c-Si exhibited very low dark current of 15 pA cm-2 at a negative bias field of 10 V μm-1 applied to the a-Se. The optical TOF (time of flight) measurements show that the applied bias drops almost entirely across the a-Se layer and that the a-Se hole and electron mobilities are within the range of commonly accepted values. The x-ray signal measurements demonstrate the structure has the expected x-ray quantum efficiency. We have made a back-thinned CCD coated with a-Se and although most areas of the device show a poor x-ray response, it does contain small regions which do work properly with the expected x-ray sensitivity. Improved understanding of the a-Se/c-Si interface and preparation methods should lead to properly functioning devices.

NASA's Advanced Environmental Barrier Coatings Development for SiC/SiC Ceramic Matrix Composites: Understanding Calcium Magnesium Alumino-Silicate (CMAS) Degradations and Resistance

Science.gov (United States)

Zhu, Dongming

2014-01-01

Environmental barrier coatings (EBCs) and SiCSiC ceramic matrix composites (CMCs) systems will play a crucial role in next generation turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures with improved efficiency, reduce engine weight and cooling requirements. The development of prime-reliant environmental barrier coatings is essential to the viability and reliability of the envisioned CMC engine component applications, ensuring integrated EBC-CMC system durability and designs are achievable for successful applications of the game-changing component technologies and lifing methodologies.This paper will emphasize recent NASA environmental barrier coating developments for SiCSiC turbine airfoil components, utilizing advanced coating compositions, state-of-the-art processing methods, and combined mechanical and environment testing and durability evaluations. The coating-CMC degradations in the engine fatigue-creep and operating environments are particularly complex; one of the important coating development aspects is to better understand engine environmental interactions and coating life debits, and we have particularly addressed the effect of Calcium-Magnesium-Alumino-Silicate (CMAS) from road sand or volcano-ash deposits on the durability of the environmental barrier coating systems, and how the temperature capability, stability and cyclic life of the candidate rare earth oxide and silicate coating systems will be impacted in the presence of the CMAS at high temperatures and under simulated heat flux conditions. Advanced environmental barrier coating systems, including HfO2-Si with rare earth dopant based bond coat systems, will be discussed for the performance improvements to achieve better temperature capability and CMAS resistance for future engine operating conditions.

Efficient tests for equivalence of hidden Markov processes and quantum random walks

NARCIS (Netherlands)

U. Faigle; A. Schönhuth (Alexander)

2011-01-01

htmlabstractWhile two hidden Markov process (HMP) resp.~quantum random walk (QRW) parametrizations can differ from one another, the stochastic processes arising from them can be equivalent. Here a polynomial-time algorithm is presented which can determine equivalence of two HMP parametrizations

Effect of mouthrinses with different active agents in the prevention of initial dental erosion

Directory of Open Access Journals (Sweden)

Tatiane Alexandre de Oliveira

2015-01-01

Full Text Available Introduction: Hydrochloric acid (HCl from the gastric juice is the only source of intrinsic acid, which can reach the oral cavity in cases of gastroesophageal reflux or chronic vomiting, enhancing the risk of dental erosion. Aim: Compare the effects of mouthrinses with different active agents in the prevention of initial dental erosion caused by HCl. Subjects and Methods: Casein (CAS at 0.2%, sodium hexametaphosphate (HMP at 0.02%, titanium tetrafluoride (TiF 4 at 0.34%, and stannous fluoride (SnF 2 at 0.87% were individually added to an experimental mouthrinse. The mouthrinse without additives was used as the negative control (C and a commercially available mouthrinse for erosion (ELM - Elmex ® as the reference product. Enamel specimens were exposed to human saliva and randomly assigned to 6 experimental groups (n = 8. Specimens were submitted to erosion in HCl for 10 s, followed by to the experimental mouthrinses for 30 s, and artificial saliva for 60 min. This cycle was repeated 3 times. The total amounts of calcium and phosphorus released by the specimens in the 2 nd and 3 rd erosive challenges were evaluated by atomic emission spectrometry. Statistical analysis used Shapiro-Wilks and Hartley tests, followed by one-way ANOVA and Tukey tests. Results: When compared with C, ELM and HMP presented significantly less calcium in solution, with no difference between them. All the groups showed similar and significantly less phosphorus than C, except CAS. Conclusions: HMP was the only agent that could match the protection against initial erosion of the commercially available mouthrinse in both analyses.

32 CFR 842.35 - Depreciation and maximum allowances.

Science.gov (United States)

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Depreciation and maximum allowances. 842.35... LITIGATION ADMINISTRATIVE CLAIMS Personnel Claims (31 U.S.C. 3701, 3721) § 842.35 Depreciation and maximum allowances. The military services have jointly established the “Allowance List-Depreciation Guide” to...

Dicty_cDB: VHD478 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available BC138482_1( BC138482 |pid:none) Mus musculus sacsin, mRNA (cDNA cl... 35 0.63 (Q9NZJ4) RecName: Full=Sacs...in; &AL157766_4( AL157766 |pid:none) 35 0.63 (Q9JLC8) RecName: Full=Sacsin; 35 0.63... BC171956_1( BC171956 |pid:none) Mus musculus sacsin, mRNA (cDNA cl... 35 0.63 AL732351_6( AL732351 |pid:non

Control of manganese dioxide particles resulting from in situ chemical oxidation using permanganate.

Science.gov (United States)

Crimi, Michelle; Ko, Saebom

2009-02-01

In situ chemical oxidation using permanganate is an approach to organic contaminant site remediation. Manganese dioxide particles are products of permanganate reactions. These particles have the potential to deposit in the subsurface and impact the flow-regime in/around permanganate injection, including the well screen, filter pack, and the surrounding subsurface formation. Control of these particles can allow for improved oxidant injection and transport and contact between the oxidant and contaminants of concern. The goals of this research were to determine if MnO(2) can be stabilized/controlled in an aqueous phase, and to determine the dependence of particle stabilization on groundwater characteristics. Bench-scale experiments were conducted to study the ability of four stabilization aids (sodium hexametaphosphate (HMP), Dowfax 8390, xanthan gum, and gum arabic) in maintaining particles suspended in solution under varied reaction conditions and time. Variations included particle and stabilization aid concentrations, ionic content, and pH. HMP demonstrated the most promising results, as compared to xanthan gum, gum arabic, and Dowfax 8390 based on results of spectrophotometric studies of particle behavior, particle filtration, and optical measurements of particle size and zeta potential. HMP inhibited particle settling, provided for greater particle stability, and resulted in particles of a smaller average size over the range of experimental conditions evaluated compared to results for systems that did not include HMP. Additionally, HMP did not react unfavorably with permanganate. These results indicate that the inclusion of HMP in a permanganate oxidation system improves conditions that may facilitate particle transport.

39 CFR 3.5 - Delegation of authority by Board.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Delegation of authority by Board. 3.5 Section 3.5 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE BOARD OF GOVERNORS (ARTICLE III) § 3.5 Delegation of authority by Board. As authorized by 39 U.S.C. 402, these bylaws...

Saturated salt method determination of hysteresis of Pinus sylvestris L. wood for 35 ºC isotherms

Directory of Open Access Journals (Sweden)

García Esteban, L.

2004-12-01

Full Text Available The saturated salts method was used in this study to quantify hysteresis in Pinus sylvestris L. wood, in an exercise that involved plotting the 35 ºC desorption and sorption isotherms. Nine salts were used, all of which establish stable and known relative humidity values when saturated in water The wood was kept at the relative humidity generated by each of these salts until the equilibrium moisture content (EMC was reached, both in the water loss or desorption, and the water uptake or sorption processes. The Guggenheim method was used to fit the values obtained to the respective curves. Hysteresis was evaluated in terms of the hysteresis coefficient, for which a mean value of 0.87 was found.

Con este trabajo se ha cuantificado la histéresis de la madera de Pinus sylvestris L. Para ello, se han construido las isotermas de 35 ºC de adsorción y sorción, mediante el método de las sales saturadas. Se han utilizado nueve sales que cuando se saturan en agua dan lugar a unas humedades relativas estables y conocidas. La madera fue colocada bajo las distintas humedades relativas que confieren cada una de las sales hasta que alcanzaron las distintas humedades de equilibrio higroscópico, tanto en el proceso de pérdida de agua o desorción, como en el de adquisición de agua o de sorción. Los valores obtenidos fueron ajustados a las respectivas sigmoides, haciendo uso del método de Guggenheim. La valoración de la histéresis se determinó mediante el coeficiente de histéresis, obteniendo un valor medio de 0,87.

Instrument validation system of general application

International Nuclear Information System (INIS)

Filshtein, E.L.

1990-01-01

This paper describes the Instrument Validation System (IVS) as a software system which has the capability of evaluating the performance of a set of functionally related instrument channels to identify failed instruments and to quantify instrument drift. Under funding from Combustion Engineering (C-E), the IVS has been developed to the extent that a computer program exists whose use has been demonstrated. The initial development work shows promise for success and for wide application, not only to power plants, but also to industrial manufacturing and process control. Applications in the aerospace and military sector are also likely