Software for the Local Control and Instrumentation System for MFTF

International Nuclear Information System (INIS)

Labiak, W.G.

1979-01-01

There are nine different systems requiring over fifty computers in the Local Control and Instrumentation System for the Mirror Fusion Test Facility. Each computer system consists of an LSI-11/2 processor with 32,000 words of memory, a serial driver that implements the CAMAC serial highway protocol. With this large number of systems it is important that as much software as possible be common to all systems. A serial communications system has been developed for data transfers between the LSI-11/2's and the supervisory computers. This system is based on the RS 232 C interface with modem control lines. Six modem control lines are used for hardware handshaking, which allows totally independent full duplex communications to occur. Odd parity on each byte and a 16-bit checksum are used to detect errors in transmission

Software quality assurance plan for void fraction instrument

International Nuclear Information System (INIS)

Gimera, M.

1994-01-01

Waste Tank SY-101 has been the focus of extensive characterization work over the past few years. The waste continually generates gases, most notably hydrogen, which are periodically released from the waste. Gas can be trapped in tank waste in three forms: as void gas (bubbles), dissolved gas, or absorbed gas. Void fraction is the volume percentage of a given sample that is comprised of void gas. The void fraction instrument (VFI) acquires the data necessary to calculate void fraction. This document covers the product, Void Fraction Data Acquisition Software. The void fraction software being developed will have the ability to control the void fraction instrument hardware and acquire data necessary to calculate the void fraction in samples. This document provides the software quality assurance plan, verification and validation plan, and configuration management plan for developing the software for the instrumentation that will be used to obtain void fraction data from Tank SY-101

Design of instrumentation and software for precise laser machining

Science.gov (United States)

Wyszyński, D.; Grabowski, Marcin; Lipiec, Piotr

2017-10-01

The paper concerns the design of instrumentation and software for precise laser machining. Application of advanced laser beam manipulation instrumentation enables noticeable improvement of cut quality and material loss. This factors have significant impact on process efficiency and cutting edge quality by means of machined part size and shape accuracy, wall taper, material loss reduction (e.g. diamond) and time effectiveness. The goal can be reached by integration of laser drive, observation and optical measurement system, beam manipulation system and five axis mechanical instrumentation with use of advanced tailored software enabling full laser cutting process control and monitoring.

DEVELOPING EVALUATION INSTRUMENT FOR MATHEMATICS EDUCATIONAL SOFTWARE

Directory of Open Access Journals (Sweden)

Wahyu Setyaningrum

2012-02-01

Full Text Available The rapid increase and availability of mathematics software, either for classroom or individual learning activities, presents a challenge for teachers. It has been argued that many products are limited in quality. Some of the more commonly used software products have been criticized for poor content, activities which fail to address some learning issues, poor graphics presentation, inadequate documentation, and other technical problems. The challenge for schools is to ensure that the educational software used in classrooms is appropriate and effective in supporting intended outcomes and goals. This paper aimed to develop instrument for evaluating mathematics educational software in order to help teachers in selecting the appropriate software. The instrument considers the notion of educational including content, teaching and learning skill, interaction, and feedback and error correction; and technical aspects of educational software including design, clarity, assessment and documentation, cost and hardware and software interdependence. The instrument use a checklist approach, the easier and effective methods in assessing the quality of educational software, thus the user needs to put tick in each criteria. The criteria in this instrument are adapted and extended from standard evaluation instrument in several references.   Keywords: mathematics educational software, educational aspect, technical aspect.

The U.S./IAEA Workshop on Software Sustainability for Safeguards Instrumentation

Energy Technology Data Exchange (ETDEWEB)

Pepper S. E.; .; Worrall, L.; Pickett, C.; Bachner, K.; Queirolo, A.

2014-08-08

The U.S. National Nuclear Security Administration’s Next Generation Safeguards Initiative, the U.S. Department of State, and the International Atomic Energy Agency (IAEA) organized a a workshop on the subject of ”Software Sustainability for Safeguards Instrumentation.” The workshop was held at the Vienna International Centre in Vienna, Austria, May 6-8, 2014. The workshop participants included software and hardware experts from national laboratories, industry, government, and IAEA member states who were specially selected by the workshop organizers based on their experience with software that is developed for the control and operation of safeguards instrumentation. The workshop included presentations, to orient the participants to the IAEA Department of Safeguards software activities related to instrumentation data collection and processing, and case studies that were designed to inspire discussion of software development, use, maintenance, and upgrades in breakout sessions and to result in recommendations for effective software practices and management. This report summarizes the results of the workshop.

A survey on the high reliability software verification and validation technology for instrumentation and control in NPP.

Energy Technology Data Exchange (ETDEWEB)

Kwon, Kee Choon; Lee, Chang Soo; Dong, In Sook [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1994-01-01

This document presents the technical status of the software verification and validation (V and V) efforts to support developing and licensing digital instrumentation and control (I and C) systems in nuclear power plants. We have reviewed codes and standards to be concensus criteria among vendor, licensee and licenser. Then we have described the software licensing procedures under 10 CFR 50 and 10 CFR 52 of the United States cope with the licensing barrier. At last, we have surveyed the technical issues related to developing and licensing the high integrity software for digital I and C systems. These technical issues let us know the development direction of our own software V and V methodology. (Author) 13 refs., 2 figs.,.

Cross-instrument Analysis Correlation Software

Energy Technology Data Exchange (ETDEWEB)

2017-06-28

This program has been designed to assist with the tracking of a sample from one analytical instrument to another such as SEM, microscopes, micro x-ray diffraction and other instruments where particular positions/locations on the sample are examined, photographed, etc. The software is designed to easily enter the position of fiducials and locations of interest such that in a future session in the same of different instrument the positions of interest can be re-found through using the known location fiducials in the current and reference session to transform the point into the current sessions coordinate system. The software is dialog box driven guiding the user through the necessary data entry and program choices. Information is stored in a series of text based extensible markup language (XML) files.

Validation procedures of software applied in nuclear instruments. Proceedings of a technical meeting

International Nuclear Information System (INIS)

2007-09-01

The IAEA has supported the availability of well functioning nuclear instruments in Member States over more than three decades. Some older or aged instruments are still being used and are still in good working condition. However, those instruments may not meet modern software requirements for the end-user in all cases. Therefore, Member States, mostly those with emerging economies, modernize/refurbish such instruments to meet the end-user demands. New advanced software is not only applied in case of new instrumentation, but often also for new and improved applications of modernized and/or refurbished instruments in many Member States for which in few cases the IAEA also provided support. Modern software applied in nuclear instrumentation plays a key role for their safe operation and execution of commands in a user friendly manner. Correct data handling and transfer has to be ensured. Additional features such as data visualization, interfacing to PC for control and data storage are often included. To finalize the task, where new instrumentation which is not commercially available is used, or aged instruments are modernized/refurbished, the applied software has to be verified and validated. A Technical Meeting on 'Validation Procedures of Software Applied in Nuclear Instruments' was organized in Vienna, 20-23 November 2006, to discuss the verification and validation process of software applied to operation and use of nuclear instruments. The presentations at the technical meeting included valuable information, which has been compiled and summarized in this publication, which should be useful for technical staff in Member States when modernizing/refurbishing nuclear instruments. 22 experts in the field of modernization/refurbishment of nuclear instruments as well as users of applied software presented their latest results. Discussion sessions followed the presentations. This publication is the outcome of deliberations during the meeting

Detailed design and first tests of the application software for the instrument control unit of Euclid-NISP

Science.gov (United States)

Ligori, S.; Corcione, L.; Capobianco, V.; Bonino, D.; Sirri, G.; Fornari, F.; Giacomini, F.; Patrizii, L.; Valenziano, L.; Travaglini, R.; Colodro, C.; Bortoletto, F.; Bonoli, C.; Chiarusi, T.; Margiotta, A.; Mauri, N.; Pasqualini, L.; Spurio, M.; Tenti, M.; Dal Corso, F.; Dusini, S.; Laudisio, F.; Sirignano, C.; Stanco, L.; Ventura, S.; Auricchio, N.; Balestra, A.; Franceschi, E.; Morgante, G.; Trifoglio, M.; Medinaceli, E.; Guizzo, G. P.; Debei, S.; Stephen, J. B.

2016-07-01

In this paper we describe the detailed design of the application software (ASW) of the instrument control unit (ICU) of NISP, the Near-Infrared Spectro-Photometer of the Euclid mission. This software is based on a real-time operating system (RTEMS) and will interface with all the subunits of NISP, as well as the command and data management unit (CDMU) of the spacecraft for telecommand and housekeeping management. We briefly review the main requirements driving the design and the architecture of the software that is approaching the Critical Design Review level. The interaction with the data processing unit (DPU), which is the intelligent subunit controlling the detector system, is described in detail, as well as the concept for the implementation of the failure detection, isolation and recovery (FDIR) algorithms. The first version of the software is under development on a Breadboard model produced by AIRBUS/CRISA. We describe the results of the tests and the main performances and budgets.

Using XML and Java for Astronomical Instrumentation Control

Science.gov (United States)

Ames, Troy; Koons, Lisa; Sall, Ken; Warsaw, Craig

2000-01-01

Traditionally, instrument command and control systems have been highly specialized, consisting mostly of custom code that is difficult to develop, maintain, and extend. Such solutions are initially very costly and are inflexible to subsequent engineering change requests, increasing software maintenance costs. Instrument description is too tightly coupled with details of implementation. NASA Goddard Space Flight Center is developing a general and highly extensible framework that applies to any kind of instrument that can be controlled by a computer. The software architecture combines the platform independent processing capabilities of Java with the power of the Extensible Markup Language (XML), a human readable and machine understandable way to describe structured data. A key aspect of the object-oriented architecture is software that is driven by an instrument description, written using the Instrument Markup Language (IML). ]ML is used to describe graphical user interfaces to control and monitor the instrument, command sets and command formats, data streams, and communication mechanisms. Although the current effort is targeted for the High-resolution Airborne Wideband Camera, a first-light instrument of the Stratospheric Observatory for Infrared Astronomy, the framework is designed to be generic and extensible so that it can be applied to any instrument.

Rapid Software Development for Experiment Control at OPAL

International Nuclear Information System (INIS)

Hathaway, P.V.; Lam, Tony; Franceschini, Ferdi; Hauser, Nick; Rayner, Hugh

2005-01-01

Full text: ANSTO is undertaking the parallel development of instrument control and graphical experiment interface software for seven neutron beam instruments at OPAL. Each instrument poses several challenges for a common system solution, including custom detector interfaces, a range of motion and beamline optics schema, and a spectrum of online data reduction requirements. To provide a superior system with the least development effort, the computing team have adopted proven, configurable, server-based control software (SICS)1., a highly Integrated Scientific Experimental Environment (GumTree)2. and industry-standard database management systems. The resulting graphical interfaces allow operation in a familiar experiment domain, with monitoring of data and parameters independent of control system specifics. GumTree presents the experimenter with a consistent interface for experiment management, instrument control and data reduction tasks. The facility instrument scientists can easily reconfigure instruments and add ancillaries. The user community can expect a reduced learning curve for performing each experiment. GumTree can be installed anywhere for pre-experiment familiarisation, postprocessing of acquired data sets, and integration with third party analysis tools. Instrument scientists are seeing faster software development iterations and have a solid basis to prepare for the next suite of instruments. 1. SICS from PSI (lns00.psi.ch). 2. GumTree (gumtree.sourceforge.net), new site: http://gumtree.sourceforge.net/wiki/index.php/Main_Page

Target Diagnostic Instrument-Based Controls Framework for the National Ignition Facility

International Nuclear Information System (INIS)

Shelton, R; O'Brien, D; Nelson, J; Kamperschroer, J

2007-01-01

NIF target diagnostics are being developed to observe and measure the extreme physics of targets irradiated by the 192-beam laser. The response time of target materials can be on the order of 100ps--the time it takes light to travel 3 cm--temperatures more than 100 times hotter than the surface of the sun, and pressures that exceed 109 atmospheres. Optical and x-ray diagnostics were developed and fielded to observe and record the results of the first 4-beam experiments at NIF. Hard and soft x-ray spectra were measured, and time-integrated and gated x-ray images of hydrodynamics experiments were recorded. Optical diagnostics recorded backscatter from the target, and VISAR laser velocimetry measurements were taken of laser-shocked target surfaces. Additional diagnostics are being developed and commissioned to observe and diagnose ignition implosions, including various neutron and activation diagnostics. NIF's diagnostics are being developed at LLNL and with collaborators at other sites. To accommodate the growing number of target diagnostics, an Instrument-Based Controls hardware-software framework has been developed to facilitate development and ease integration into the NIF Integrated Computer Control System (ICCS). Individual WindowsXP PC controllers for each digitizer, power supply and camera (i.e., instruments) execute controls software unique to each instrument model. Each hardware-software controller manages a single instrument, in contrast to the complexity of combining all the controls software needed for a diagnostic into a single controller. Because of this simplification, controllers can be more easily tested on the actual hardware, evaluating all normal and off-normal conditions. Each target diagnostic is then supported by a number of instruments, each with its own hardware-software instrument-based controller. Advantages of the instrument-based control architecture and framework include reusability, testability, and improved reliability of the deployed

Target Diagnostic Instrument-Based Controls Framework for the National Ignition Facility

Energy Technology Data Exchange (ETDEWEB)

Shelton, R; O' Brien, D; Nelson, J; Kamperschroer, J

2007-05-07

NIF target diagnostics are being developed to observe and measure the extreme physics of targets irradiated by the 192-beam laser. The response time of target materials can be on the order of 100ps--the time it takes light to travel 3 cm--temperatures more than 100 times hotter than the surface of the sun, and pressures that exceed 109 atmospheres. Optical and x-ray diagnostics were developed and fielded to observe and record the results of the first 4-beam experiments at NIF. Hard and soft x-ray spectra were measured, and time-integrated and gated x-ray images of hydrodynamics experiments were recorded. Optical diagnostics recorded backscatter from the target, and VISAR laser velocimetry measurements were taken of laser-shocked target surfaces. Additional diagnostics are being developed and commissioned to observe and diagnose ignition implosions, including various neutron and activation diagnostics. NIF's diagnostics are being developed at LLNL and with collaborators at other sites. To accommodate the growing number of target diagnostics, an Instrument-Based Controls hardware-software framework has been developed to facilitate development and ease integration into the NIF Integrated Computer Control System (ICCS). Individual WindowsXP PC controllers for each digitizer, power supply and camera (i.e., instruments) execute controls software unique to each instrument model. Each hardware-software controller manages a single instrument, in contrast to the complexity of combining all the controls software needed for a diagnostic into a single controller. Because of this simplification, controllers can be more easily tested on the actual hardware, evaluating all normal and off-normal conditions. Each target diagnostic is then supported by a number of instruments, each with its own hardware-software instrument-based controller. Advantages of the instrument-based control architecture and framework include reusability, testability, and improved reliability of the

Virtual instrumentation: a new approach for control and instrumentation - application in containment studies facility

International Nuclear Information System (INIS)

Gole, N.V.; Shanware, V.M.; Sebastian, A.; Subramaniam, K.

2001-01-01

PC based data-acquisition has emerged as a rapidly developing area particularly with respect to process instrumentation. Computer based data acquisition in process instrumentation combined with Supervisory Control and Data Acquisition (SCADA) software has introduced extensive possibilities with respect to formats for presentation of information. The concept of presenting data using any instrument format with the help of software tools to simulate the instrument on screen, needs to be understood, in order to be able to make use of its vast potential. The purpose of this paper is to present the significant features of the Virtual Instrumentation concept and discuss its application in the instrumentation and control system of containment studies facility (CSF). Factors involved in the development of the virtual instrumentation based I and C system for CSF are detailed and a functional overview of the system configuration is given. (author)

Software System for the Calibration of X-Ray Measuring Instruments

International Nuclear Information System (INIS)

Gaytan-Gallardo, E.; Tovar-Munoz, V. M.; Cruz-Estrada, P.; Vergara-Martinez, F. J.; Rivero-Gutierrez, T.

2006-01-01

A software system that facilities the calibration of X-ray measuring instruments used in medical applications is presented. The Secondary Standard Dosimetry Laboratory (SSDL) of the Nuclear Research National Institute in Mexico (ININ in Spanish), supports activities concerning with ionizing radiations in medical area. One of these activities is the calibration of X-ray measuring instruments, in terms of air kerma or exposure by substitution method in an X-ray beam at a point where the rate has been determined by means of a standard ionization chamber. To automatize this process, a software system has been developed, the calibration system is composed by an X-ray unit, a Dynalizer IIIU X-ray meter by RADCAL, a commercial data acquisition card, the software system and the units to be tested and calibrated. A quality control plan has been applied in the development of the software system, ensuring that quality assurance procedures and standards are being followed

CLOUDCLOUD : general-purpose instrument monitoring and data managing software

Science.gov (United States)

Dias, António; Amorim, António; Tomé, António

2016-04-01

An effective experiment is dependent on the ability to store and deliver data and information to all participant parties regardless of their degree of involvement in the specific parts that make the experiment a whole. Having fast, efficient and ubiquitous access to data will increase visibility and discussion, such that the outcome will have already been reviewed several times, strengthening the conclusions. The CLOUD project aims at providing users with a general purpose data acquisition, management and instrument monitoring platform that is fast, easy to use, lightweight and accessible to all participants of an experiment. This work is now implemented in the CLOUD experiment at CERN and will be fully integrated with the experiment as of 2016. Despite being used in an experiment of the scale of CLOUD, this software can also be used in any size of experiment or monitoring station, from single computers to large networks of computers to monitor any sort of instrument output without influencing the individual instrument's DAQ. Instrument data and meta data is stored and accessed via a specially designed database architecture and any type of instrument output is accepted using our continuously growing parsing application. Multiple databases can be used to separate different data taking periods or a single database can be used if for instance an experiment is continuous. A simple web-based application gives the user total control over the monitored instruments and their data, allowing data visualization and download, upload of processed data and the ability to edit existing instruments or add new instruments to the experiment. When in a network, new computers are immediately recognized and added to the system and are able to monitor instruments connected to them. Automatic computer integration is achieved by a locally running python-based parsing agent that communicates with a main server application guaranteeing that all instruments assigned to that computer are

Application range affected by software failures in safety relevant instrumentation and control systems of nuclear power plants

International Nuclear Information System (INIS)

Jopen, Manuela; Mbonjo, Herve; Sommer, Dagmar; Ulrich, Birte

2017-03-01

This report presents results that have been developed within a BMUB-funded research project (Promotion Code 3614R01304). The overall objective of this project was to broaden the knowledge base of GRS regarding software failures and their impact in software-based instrumentation and control (I and C) systems. To this end, relevant definitions and terms in standards and publications (DIN, IEEE standards, IAEA standards, NUREG publications) as well as in the German safety requirements for nuclear power plants were analyzed first. In particular, it was found that the term ''software fault'' is defined differently and partly contradictory in the considered literature sources. For this reason, a definition of software fault was developed on the basis of the software life cycle of software-based I and C systems within the framework of this project, which takes into account the various aspects relevant to software faults and their related effects. It turns out that software failures result from latent faults in a software-based control system, which can lead to a non-compliant behavior of a software-based I and C system. Hereby a distinction should be made between programming faults and specification faults. In a further step, operational experience with software failures in software-based I and C systems in nuclear facilities and in nonnuclear sector was investigated. The identified events were analyzed with regard to their cause and impacts and the analysis results were summarized. Based on the developed definition of software failure and on the COMPSIS-classification scheme for events related to software based I and C systems, the COCS-classification scheme was developed to classify events from operating experience with software failures, in which the events are classified according to the criteria ''cause'', ''affected system'', ''impact'' and ''CCF potential''. This classification scheme was applied to evaluate the events identified in the framework of this project

XML in an Adaptive Framework for Instrument Control

Science.gov (United States)

Ames, Troy J.

2004-01-01

NASA Goddard Space Flight Center is developing an extensible framework for instrument command and control, known as Instrument Remote Control (IRC), that combines the platform independent processing capabilities of Java with the power of the Extensible Markup Language (XML). A key aspect of the architecture is software that is driven by an instrument description, written using the Instrument Markup Language (IML). IML is an XML dialect used to describe interfaces to control and monitor the instrument, command sets and command formats, data streams, communication mechanisms, and data processing algorithms.

Research on the evaluation model of the software reliability in nuclear safety class digital instrumentation and control system

International Nuclear Information System (INIS)

Liu Ying; Yang Ming; Li Fengjun; Ma Zhanguo; Zeng Hai

2014-01-01

In order to analyze the software reliability (SR) in nuclear safety class digital instrumentation and control system (D-I and C), firstly, the international software design standards were analyzed, the standards' framework was built, and we found that the D-I and C software standards should follow the NUREG-0800 BTP7-14, according to the NRC NUREG-0800 review of requirements. Secondly, the quantitative evaluation model of SR using Bayesian Belief Network and thirteen sub-model frameworks were established. Thirdly, each sub-models and the weight of corresponding indexes in the evaluation model were analyzed. Finally, the safety case was introduced. The models lay a foundation for review and quantitative evaluation on the SR in nuclear safety class D-I and C. (authors)

ADAA: new software for intelligent instrument control

International Nuclear Information System (INIS)

Butman, M.; Wannberg, A.; Mellergaard, A.; Zetterstroem, P.; McGreevy, R.L.

2004-01-01

Automated data acquisition and analysis (ADAA) is a new platform for automation of experiments, including data reduction, analysis and feedback. The objective of ADAA is to develop software that enables scientific control of the progress of an experiment, e.g. monitoring in terms of analysed data as opposed to measured data, one obvious aim being to maximize the scientific output from a given period of beam time. Basic design considerations will be outlined and discussed in the context of several types of experiments

Software change control in the Sizewell B ISCO

International Nuclear Information System (INIS)

Johnson, A.

1997-01-01

Central to the control and instrumentation system of the Sizewell B nuclear power plant is a control, data acquisition and control system based on a distributed network of several hundred microprocessors. The system has been integrated into a single functional unity, and software modifications affecting one part of it have an effect on the other parts. The software modification and configuration processes are therefore kept as similar as possible. (A.K.)

Design type testing for digital instrumentation and control systems

International Nuclear Information System (INIS)

Bastl, W.; Mohns, G.

1997-01-01

The design type qualification of digital safety instrumentation and control is outlined. Experience shows that the concepts discussed, derived from codes, guidelines and standards, achieve useful results. It has likewise become clear that the systematics of design type qualification of the hardware components is also applicable to the software components. Design type qualification of the software, a premiere, could be performed unexpectedly smoothly. The hardware design type qualification proved that the hardware as a substrate of functionality and reliability is an issue that demands full attention, as compared to conventional systems. Another insight is that design qualification of digital instrumentation and control systems must include plant-independent systems tests. Digital instrumentation and control systems simply work very differently from conventional control systems, so that this testing modality is inevitable. (Orig./CB) [de

Reliability Estimation for Digital Instrument/Control System

Energy Technology Data Exchange (ETDEWEB)

Yang, Yaguang; Sydnor, Russell [U.S. Nuclear Regulatory Commission, Washington, D.C. (United States)

2011-08-15

Digital instrumentation and controls (DI and C) systems are widely adopted in various industries because of their flexibility and ability to implement various functions that can be used to automatically monitor, analyze, and control complicated systems. It is anticipated that the DI and C will replace the traditional analog instrumentation and controls (AI and C) systems in all future nuclear reactor designs. There is an increasing interest for reliability and risk analyses for safety critical DI and C systems in regulatory organizations, such as The United States Nuclear Regulatory Commission. Developing reliability models and reliability estimation methods for digital reactor control and protection systems will involve every part of the DI and C system, such as sensors, signal conditioning and processing components, transmission lines and digital communication systems, D/A and A/D converters, computer system, signal processing software, control and protection software, power supply system, and actuators. Some of these components are hardware, such as sensors and actuators, their failure mechanisms are well understood, and the traditional reliability model and estimation methods can be directly applied. But many of these components are firmware which has software embedded in the hardware, and software needs special consideration because its failure mechanism is unique, and the reliability estimation method for a software system will be different from the ones used for hardware systems. In this paper, we will propose a reliability estimation method for the entire DI and C system reliability using a recently developed software reliability estimation method and a traditional hardware reliability estimation method.

Reliability Estimation for Digital Instrument/Control System

International Nuclear Information System (INIS)

Yang, Yaguang; Sydnor, Russell

2011-01-01

Digital instrumentation and controls (DI and C) systems are widely adopted in various industries because of their flexibility and ability to implement various functions that can be used to automatically monitor, analyze, and control complicated systems. It is anticipated that the DI and C will replace the traditional analog instrumentation and controls (AI and C) systems in all future nuclear reactor designs. There is an increasing interest for reliability and risk analyses for safety critical DI and C systems in regulatory organizations, such as The United States Nuclear Regulatory Commission. Developing reliability models and reliability estimation methods for digital reactor control and protection systems will involve every part of the DI and C system, such as sensors, signal conditioning and processing components, transmission lines and digital communication systems, D/A and A/D converters, computer system, signal processing software, control and protection software, power supply system, and actuators. Some of these components are hardware, such as sensors and actuators, their failure mechanisms are well understood, and the traditional reliability model and estimation methods can be directly applied. But many of these components are firmware which has software embedded in the hardware, and software needs special consideration because its failure mechanism is unique, and the reliability estimation method for a software system will be different from the ones used for hardware systems. In this paper, we will propose a reliability estimation method for the entire DI and C system reliability using a recently developed software reliability estimation method and a traditional hardware reliability estimation method

Contribution to the safety assessment of instrumentation and control software for nuclear power plants. Application to spin N4

International Nuclear Information System (INIS)

Soubies, B.; Boulc'h, J.; Elsensohn, O.; Le Meur, M.; Henry, J.Y.

1994-01-01

The process of licensing nuclear power plants for operation consists of mandatory steps featuring detailed examination of the instrumentation and control system. Significant changes were introduced by the operator in the process of designing and producing 1400 MWe pressurized water reactor safety systems and, in particular, in the case of the Digital Integrated Protection System, (French abbreviation SPIN). The methodology applied by the Institute of Protection and Nuclear Safety (IPSN) to examine the software of this system is described. It consists of the methods used by the manufacturer to develop SPIN software for the 1400 MWe PWRs, and the approach adopted by the IPSN to evaluate SPIN safety softwares of the protection system for the N4 series of reactors. (R.P.). 2 refs

Development of remote control software for multiformat test signal generator

Directory of Open Access Journals (Sweden)

Gao Yang

2017-01-01

Full Text Available The multi format test signal generator mentioned in this paper is the video signal generator named TG8000 produced by Tektronix Company. I will introduce the function about remote control for signal generator, how to connect the computer to the instrument, and how to remote control. My topic uses my computer to connect the instrument through the 10/100/1000 BASE-T port on the rear panel of TG8000. Then I write program to transmit SCPI (Standard Commands for Programmable Instruments to control TG8000. The application is running on the Windows operating system, the programming language is C#, development environment is Microsoft Visual Studio 2010, using the TCP/IP protocol based on Socket. And the method of remote control refers to the application called TGSetup which is developed by Tektronix Company. This paper includes a brief summary of the basic principle, and introduce for details about the process of remote control software development, and how to use my software. In the end, I will talk about the advantages of my software compared with another one.

Using XML and Java Technologies for Astronomical Instrument Control

Science.gov (United States)

Ames, Troy; Case, Lynne; Powers, Edward I. (Technical Monitor)

2001-01-01

Traditionally, instrument command and control systems have been highly specialized, consisting mostly of custom code that is difficult to develop, maintain, and extend. Such solutions are initially very costly and are inflexible to subsequent engineering change requests, increasing software maintenance costs. Instrument description is too tightly coupled with details of implementation. NASA Goddard Space Flight Center, under the Instrument Remote Control (IRC) project, is developing a general and highly extensible framework that applies to any kind of instrument that can be controlled by a computer. The software architecture combines the platform independent processing capabilities of Java with the power of the Extensible Markup Language (XML), a human readable and machine understandable way to describe structured data. A key aspect of the object-oriented architecture is that the software is driven by an instrument description, written using the Instrument Markup Language (IML), a dialect of XML. IML is used to describe the command sets and command formats of the instrument, communication mechanisms, format of the data coming from the instrument, and characteristics of the graphical user interface to control and monitor the instrument. The IRC framework allows the users to define a data analysis pipeline which converts data coming out of the instrument. The data can be used in visualizations in order for the user to assess the data in real-time, if necessary. The data analysis pipeline algorithms can be supplied by the user in a variety of forms or programming languages. Although the current integration effort is targeted for the High-resolution Airborne Wideband Camera (HAWC) and the Submillimeter and Far Infrared Experiment (SAFIRE), first-light instruments of the Stratospheric Observatory for Infrared Astronomy (SOFIA), the framework is designed to be generic and extensible so that it can be applied to any instrument. Plans are underway to test the framework

Tank monitor and control system (TMACS) software configuration management plan

International Nuclear Information System (INIS)

GLASSCOCK, J.A.

1999-01-01

This Software Configuration Management Plan (SCMP) describes the methodology for control of computer software developed and supported by the Systems Development and Integration (SD and I) organization of Lockheed Martin Services, Inc. (LMSI) for the Tank Monitor and Control System (TMACS). This plan controls changes to the software and configuration files used by TMACS. The controlled software includes the Gensym software package, Gensym knowledge base files developed for TMACS, C-language programs used by TMACS, the operating system on the production machine, language compilers, and all Windows NT commands and functions which affect the operating environment. The configuration files controlled include the files downloaded to the Acromag and Westronic field instruments

Instrument hardware and software upgrades at IPNS

International Nuclear Information System (INIS)

Worlton, Thomas; Hammonds, John; Mikkelson, D.; Mikkelson, Ruth; Porter, Rodney; Tao, Julian; Chatterjee, Alok

2006-01-01

IPNS is in the process of upgrading their time-of-flight neutron scattering instruments with improved hardware and software. The hardware upgrades include replacing old VAX Qbus and Multibus-based data acquisition systems with new systems based on VXI and VME. Hardware upgrades also include expanded detector banks and new detector electronics. Old VAX Fortran-based data acquisition and analysis software is being replaced with new software as part of the ISAW project. ISAW is written in Java for ease of development and portability, and is now used routinely for data visualization, reduction, and analysis on all upgraded instruments. ISAW provides the ability to process and visualize the data from thousands of detector pixels, each having thousands of time channels. These operations can be done interactively through a familiar graphical user interface or automatically through simple scripts. Scripts and operators provided by end users are automatically included in the ISAW menu structure, along with those distributed with ISAW, when the application is started

Measuring Software Test Verification for Complex Workpieces based on Virtual Gear Measuring Instrument

Directory of Open Access Journals (Sweden)

Yin Peili

2017-08-01

Full Text Available Validity and correctness test verification of the measuring software has been a thorny issue hindering the development of Gear Measuring Instrument (GMI. The main reason is that the software itself is difficult to separate from the rest of the measurement system for independent evaluation. This paper presents a Virtual Gear Measuring Instrument (VGMI to independently validate the measuring software. The triangular patch model with accurately controlled precision was taken as the virtual workpiece and a universal collision detection model was established. The whole process simulation of workpiece measurement is implemented by VGMI replacing GMI and the measuring software is tested in the proposed virtual environment. Taking involute profile measurement procedure as an example, the validity of the software is evaluated based on the simulation results; meanwhile, experiments using the same measuring software are carried out on the involute master in a GMI. The experiment results indicate a consistency of tooth profile deviation and calibration results, thus verifying the accuracy of gear measuring system which includes the measurement procedures. It is shown that the VGMI presented can be applied in the validation of measuring software, providing a new ideal platform for testing of complex workpiece-measuring software without calibrated artifacts.

Computer Security of NPP Instrumentation and Control Systems: Cyber Threats

International Nuclear Information System (INIS)

Klevtsov, A.L.; Trubchaninov, S.A.

2015-01-01

The paper is devoted to cyber threats, as one of the aspects in computer security of instrumentation and control systems for nuclear power plants (NPP). The basic concepts, terms and definitions are shortly addressed. The paper presents a detailed analysis of potential cyber threats during the design and operation of NPP instrumentation and control systems. Eleven major types of threats are considered, including: the malicious software and hardware Trojans (in particular, in commercial-off-the-shelf software and hardware), computer attacks through data networks and intrusion of malicious software from an external storage media and portable devices. Particular attention is paid to the potential use of lower safety class software as a way of harmful effects (including the intrusion of malicious fragments of code) on higher safety class software. The examples of actual incidents at various nuclear facilities caused by intentional cyber attacks or unintentional computer errors during the operation of software of systems important to NPP safety.

Tank monitor and control system (TMACS) software configuration management plan; TOPICAL

International Nuclear Information System (INIS)

GLASSCOCK, J.A.

1999-01-01

This Software Configuration Management Plan (SCMP) describes the methodology for control of computer software developed and supported by the Systems Development and Integration (SD and I) organization of Lockheed Martin Services, Inc. (LMSI) for the Tank Monitor and Control System (TMACS). This plan controls changes to the software and configuration files used by TMACS. The controlled software includes the Gensym software package, Gensym knowledge base files developed for TMACS, C-language programs used by TMACS, the operating system on the production machine, language compilers, and all Windows NT commands and functions which affect the operating environment. The configuration files controlled include the files downloaded to the Acromag and Westronic field instruments

Software for simulation and design of neutron scattering instrumentation

DEFF Research Database (Denmark)

Bertelsen, Mads

designed using the software. The Union components uses a new approach to simulation of samples in McStas. The properties of a sample are split into geometrical and material, simplifying user input, and allowing the construction of complicated geometries such as sample environments. Multiple scattering...... from conventional choices. Simulation of neutron scattering instrumentation is used when designing instrumentation, but also to understand instrumental effects on the measured scattering data. The Monte Carlo ray-tracing package McStas is among the most popular, capable of simulating the path of each...... neutron through the instrument using an easy to learn language. The subject of the defended thesis is contributions to the McStas language in the form of the software package guide_bot and the Union components.The guide_bot package simplifies the process of optimizing neutron guides by writing the Mc...

Instrument Control (iC) - An Open-Source Software to Automate Test Equipment.

Science.gov (United States)

Pernstich, K P

2012-01-01

It has become common practice to automate data acquisition from programmable instrumentation, and a range of different software solutions fulfill this task. Many routine measurements require sequential processing of certain tasks, for instance to adjust the temperature of a sample stage, take a measurement, and repeat that cycle for other temperatures. This paper introduces an open-source Java program that processes a series of text-based commands that define the measurement sequence. These commands are in an intuitive format which provides great flexibility and allows quick and easy adaptation to various measurement needs. For each of these commands, the iC-framework calls a corresponding Java method that addresses the specified instrument to perform the desired task. The functionality of iC can be extended with minimal programming effort in Java or Python, and new measurement equipment can be addressed by defining new commands in a text file without any programming.

The EGSE science software of the IBIS instrument on-board INTEGRAL satellite

International Nuclear Information System (INIS)

La Rosa, Giovanni; Fazio, Giacomo; Segreto, Alberto; Gianotti, Fulvio; Stephen, John; Trifoglio, Massimo

2000-01-01

IBIS (Imager on Board INTEGRAL Satellite) is one of the key instrument on-board the INTEGRAL satellite, the follow up mission of the high energy missions CGRO and Granat. The EGSE of IBIS is composed by a Satellite Interface Simulator, a Control Station and a Science Station. Here are described the solutions adopted for the architectural design of the software running on the Science Station. Some preliminary results are used to show the science functionality, that allowed to understand the instrument behavior, all along the test and calibration campaigns of the Engineering Model of IBIS

The control software framework of the web base

International Nuclear Information System (INIS)

Nakatani, Takeshi; Inamura, Yasuhiro; Ito, Takayoshi; Otomo, Toshiya

2015-01-01

Web browsers are one of the most platform-independent user interfaces. In particular, web pages created using responsive web design (RWD) are available for use on desktop and laptop computers, as well as tablet terminals and smart phones. We developed a common software framework, IROHA, for the instrument control system in the Materials and Life Science Experimental Facility at the Japan Proton Accelerator Research Complex to build a flexible and scalable system by adopting XML/HTTP. However, its user interface was platform-dependent, and we wanted it to be more user-friendly. In 2013, we developed the prototype of a new software framework, IROHA2, comprising several device control servers and an instrument management server, retaining the flexibility and scalability of IROHA. We also adopted the Bootstrap framework to create an RWD user interface for these servers. (author)

QuickDirect - Payload Control Software Template Package, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — To address the need to quickly, cost-effectively and reliably develop software to control science instruments deployed on spacecraft, QuickFlex proposes to create a...

Safety regulations concerning instrumentation and control systems for research reactors

International Nuclear Information System (INIS)

El-Shanshoury, A.I.

2009-01-01

A brief study on the safety and reliability issues related to instrumentation and control systems in nuclear reactor plants is performed. In response, technical and strategic issues are used to accomplish instrumentation and control systems safety. For technical issues there are ; systems aspects of digital I and C technology, software quality assurance, common-mode software, failure potential, safety and reliability assessment methods, and human factors and human machine interfaces. The strategic issues are the case-by-case licensing process and the adequacy of the technical infrastructure. The purpose of this work was to review the reliability of the safety systems related to these technical issues for research reactors

Metrics-based control in outsourced software development projects

NARCIS (Netherlands)

Ponisio, Laura; van Eck, Pascal

2012-01-01

Measurements have been recognised as vital instruments to improve control in outsourced software development projects. However, project managers are still struggling with the design and implementation of effective measurement programs. One reason for this is that although there is a large body of

Proteomics Quality Control: Quality Control Software for MaxQuant Results.

Science.gov (United States)

Bielow, Chris; Mastrobuoni, Guido; Kempa, Stefan

2016-03-04

Mass spectrometry-based proteomics coupled to liquid chromatography has matured into an automatized, high-throughput technology, producing data on the scale of multiple gigabytes per instrument per day. Consequently, an automated quality control (QC) and quality analysis (QA) capable of detecting measurement bias, verifying consistency, and avoiding propagation of error is paramount for instrument operators and scientists in charge of downstream analysis. We have developed an R-based QC pipeline called Proteomics Quality Control (PTXQC) for bottom-up LC-MS data generated by the MaxQuant software pipeline. PTXQC creates a QC report containing a comprehensive and powerful set of QC metrics, augmented with automated scoring functions. The automated scores are collated to create an overview heatmap at the beginning of the report, giving valuable guidance also to nonspecialists. Our software supports a wide range of experimental designs, including stable isotope labeling by amino acids in cell culture (SILAC), tandem mass tags (TMT), and label-free data. Furthermore, we introduce new metrics to score MaxQuant's Match-between-runs (MBR) functionality by which peptide identifications can be transferred across Raw files based on accurate retention time and m/z. Last but not least, PTXQC is easy to install and use and represents the first QC software capable of processing MaxQuant result tables. PTXQC is freely available at https://github.com/cbielow/PTXQC .

Quality control of nuclear medicine instrumentation

International Nuclear Information System (INIS)

Mould, R.F.

1983-09-01

The proceedings of a conference held by the Hospital Physicists' Association in London 1983 on the quality control of nuclear medicine instrumentation are presented. Section I deals with the performance of the Anger gamma camera including assessment during manufacture, acceptance testing, routine testing and long-term assessment of results. Section II covers interfaces, computers, the quality control problems of emission tomography and the quality of software. Section III deals with radionuclide measurement and impurity assessment and Section IV the presentation of images and the control of image quality. (U.K.)

CAMAC-controlled calibration system for nuclear reactor instruments

International Nuclear Information System (INIS)

McDowell, W.P.; Cornella, R.J.

1977-01-01

The hardware and the software which have been developed to implement a nuclear instrument calibration system for the Argonne National Laboratory ZPR-VI and ZPR-IX reactor complex are described. The system is implemented using an SEL-840 computer with its associated CAMAC crates and a hardware interface to generate input parameters and measure the required outputs on the instrument under test. Both linear and logarithmic instruments can be calibrated by the system and output parameters can be measured at various automatically selected values of ac line voltage. A complete report on each instrument is printed as a result of the calibration and out-of-tolerance readings are flagged. Operator interface is provided by a CAMAC-controlled Hazeltine terminal. The terminal display leads the operator through the complete calibration procedure. This computer-controlled system is a significant improvement over previously used methods of calibrating nuclear instruments since it reduces reactor downtime and allows rapid detection of long-term changes in instrument calibration

Development of intelligent instruments with embedded HTTP servers for control and data acquisition in a cryogenic setup—The hardware, firmware, and software implementation

Science.gov (United States)

Antony, Joby; Mathuria, D. S.; Datta, T. S.; Maity, Tanmoy

2015-12-01

The power of Ethernet for control and automation technology is being largely understood by the automation industry in recent times. Ethernet with HTTP (Hypertext Transfer Protocol) is one of the most widely accepted communication standards today. Ethernet is best known for being able to control through internet from anywhere in the globe. The Ethernet interface with built-in on-chip embedded servers ensures global connections for crate-less model of control and data acquisition systems which have several advantages over traditional crate-based control architectures for slow applications. This architecture will completely eliminate the use of any extra PLC (Programmable Logic Controller) or similar control hardware in any automation network as the control functions are firmware coded inside intelligent meters itself. Here, we describe the indigenously built project of a cryogenic control system built for linear accelerator at Inter University Accelerator Centre, known as "CADS," which stands for "Complete Automation of Distribution System." CADS deals with complete hardware, firmware, and software implementation of the automated linac cryogenic distribution system using many Ethernet based embedded cryogenic instruments developed in-house. Each instrument works as an intelligent meter called device-server which has the control functions and control loops built inside the firmware itself. Dedicated meters with built-in servers were designed out of ARM (Acorn RISC (Reduced Instruction Set Computer) Machine) and ATMEL processors and COTS (Commercially Off-the-Shelf) SMD (Surface Mount Devices) components, with analog sensor front-end and a digital back-end web server implementing remote procedure call over HTTP for digital control and readout functions. At present, 24 instruments which run 58 embedded servers inside, each specific to a particular type of sensor-actuator combination for closed loop operations, are now deployed and distributed across control LAN (Local

Development of intelligent instruments with embedded HTTP servers for control and data acquisition in a cryogenic setup--The hardware, firmware, and software implementation.

Science.gov (United States)

Antony, Joby; Mathuria, D S; Datta, T S; Maity, Tanmoy

2015-12-01

The power of Ethernet for control and automation technology is being largely understood by the automation industry in recent times. Ethernet with HTTP (Hypertext Transfer Protocol) is one of the most widely accepted communication standards today. Ethernet is best known for being able to control through internet from anywhere in the globe. The Ethernet interface with built-in on-chip embedded servers ensures global connections for crate-less model of control and data acquisition systems which have several advantages over traditional crate-based control architectures for slow applications. This architecture will completely eliminate the use of any extra PLC (Programmable Logic Controller) or similar control hardware in any automation network as the control functions are firmware coded inside intelligent meters itself. Here, we describe the indigenously built project of a cryogenic control system built for linear accelerator at Inter University Accelerator Centre, known as "CADS," which stands for "Complete Automation of Distribution System." CADS deals with complete hardware, firmware, and software implementation of the automated linac cryogenic distribution system using many Ethernet based embedded cryogenic instruments developed in-house. Each instrument works as an intelligent meter called device-server which has the control functions and control loops built inside the firmware itself. Dedicated meters with built-in servers were designed out of ARM (Acorn RISC (Reduced Instruction Set Computer) Machine) and ATMEL processors and COTS (Commercially Off-the-Shelf) SMD (Surface Mount Devices) components, with analog sensor front-end and a digital back-end web server implementing remote procedure call over HTTP for digital control and readout functions. At present, 24 instruments which run 58 embedded servers inside, each specific to a particular type of sensor-actuator combination for closed loop operations, are now deployed and distributed across control LAN (Local

Designing communication and remote controlling of virtual instrument network system

Science.gov (United States)

Lei, Lin; Wang, Houjun; Zhou, Xue; Zhou, Wenjian

2005-01-01

In this paper, a virtual instrument network through the LAN and finally remote control of virtual instruments is realized based on virtual instrument and LabWindows/CVI software platform. The virtual instrument network system is made up of three subsystems. There are server subsystem, telnet client subsystem and local instrument control subsystem. This paper introduced virtual instrument network structure in detail based on LabWindows. Application procedure design of virtual instrument network communication, the Client/the programming mode of the server, remote PC and server communication far realizing, the control power of the workstation is transmitted, server program and so on essential technical were introduced. And virtual instruments network may connect to entire Internet on. Above-mentioned technology, through measuring the application in the electronic measurement virtual instrument network that is already built up, has verified the actual using value of the technology. Experiment and application validate that this design is resultful.

Designing communication and remote controlling of virtual instrument network system

International Nuclear Information System (INIS)

Lei Lin; Wang Houjun; Zhou Xue; Zhou Wenjian

2005-01-01

In this paper, a virtual instrument network through the LAN and finally remote control of virtual instruments is realized based on virtual instrument and LabWindows/CVI software platform. The virtual instrument network system is made up of three subsystems. There are server subsystem, telnet client subsystem and local instrument control subsystem. This paper introduced virtual instrument network structure in detail based on LabWindows. Application procedure design of virtual instrument network communication, the Client/the programming mode of the server, remote PC and server communication far realizing, the control power of the workstation is transmitted, server program and so on essential technical were introduced. And virtual instruments network may connect to entire Internet on. Above-mentioned technology, through measuring the application in the electronic measurement virtual instrument network that is already built up, has verified the actual using value of the technology. Experiment and application validate that this design is resultful

Instrument Control (iC) – An Open-Source Software to Automate Test Equipment

Science.gov (United States)

Pernstich, K. P.

2012-01-01

It has become common practice to automate data acquisition from programmable instrumentation, and a range of different software solutions fulfill this task. Many routine measurements require sequential processing of certain tasks, for instance to adjust the temperature of a sample stage, take a measurement, and repeat that cycle for other temperatures. This paper introduces an open-source Java program that processes a series of text-based commands that define the measurement sequence. These commands are in an intuitive format which provides great flexibility and allows quick and easy adaptation to various measurement needs. For each of these commands, the iC-framework calls a corresponding Java method that addresses the specified instrument to perform the desired task. The functionality of iC can be extended with minimal programming effort in Java or Python, and new measurement equipment can be addressed by defining new commands in a text file without any programming. PMID:26900522

Note: Tormenta: An open source Python-powered control software for camera based optical microscopy.

Science.gov (United States)

Barabas, Federico M; Masullo, Luciano A; Stefani, Fernando D

2016-12-01

Until recently, PC control and synchronization of scientific instruments was only possible through closed-source expensive frameworks like National Instruments' LabVIEW. Nowadays, efficient cost-free alternatives are available in the context of a continuously growing community of open-source software developers. Here, we report on Tormenta, a modular open-source software for the control of camera-based optical microscopes. Tormenta is built on Python, works on multiple operating systems, and includes some key features for fluorescence nanoscopy based on single molecule localization.

Software V and V methods for a safety - grade programmable logic controller

International Nuclear Information System (INIS)

Jang Yeol Kim; Young Jun Lee; Kyung Ho Cha; Se Woo Cheon; Jang Soo Lee; Kee Choon Kwon

2006-01-01

This paper addresses the Verification and Validation(V and V) process and the methodology for an embedded real time software of a safety-grade Programmable Logic Controller(PLC). This safety- grade PLC is being developed as one of the Korean Nuclear Instrumentation and Control System (KNICS) projects. KNICS projects are developing a Reactor Protection System(RPS) and an Engineered Safety Feature-Component Control System(ESF-CCS) as well as a safety-grade PLC. The safety-grade PLC will be a major component that encomposes the RPS systems and the ESF-CCS systems as nuclear instruments and control equipment. This paper describes the V and V guidelines and procedures, V and V environment, V and V process and methodology, and the V and V tools in the KNICS projects. Specifically, it describes the real-time operating system V and V experience which corresponds to the requirement analysis phase, design phase and the implementation and testing phase of the software development life cycle. Main activities of the V and V for the PLC system software are a technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, software safety analysis, and a software configuration management. The proposed V and V methodology satisfies the Standard Review Plan(SRP)/Branch Technical Position(BTP)-14 criteria for the safety software in nuclear power plants. The proposed V and V methodology is going to be used to verify the upcoming software life cycle in the KNICS projects. (author)

System 80+ instrumentation and controls - certification of a reliable design

International Nuclear Information System (INIS)

Matzie, R.A.; Scarola, K.; Turk, R.S.

1993-01-01

ABB Combustion Engineering's (ABB) System 80+ advanced light water plant design includes a modern, fully digitized instrumentation and controls complex, Nuplex 80+. This complex incorporates an evolutionary advanced control room, replacing conventional analog instruments with more capable computer driven components. As a result, Nuplex 80+ results in significant improvements in operator information handling and control to enhance plant safety and availability. The design implements features which the U.S. NRC has determined to be acceptable for addressing the potential for common mode failure in software implemented for protective functions. (author)

The development of advanced instrumentation and control technology. The development of verification and validation technology for instrumentation and control in NPPs

International Nuclear Information System (INIS)

Kwon, Kee Choon; Ham, Chang Shik; Lee, Jang Soo; Kim, Jang Yeol; Song, Soon Ja; Kim, Jung Taek; Park, Won Man; Lee, Dong Young; Eom, Heung Seop; Park, Kee Yong.

1997-07-01

We found essential problems followed by digitalizing of instrumentation and control. A scheme is divided into hardware and software to resolve these problems. We have analyzed the hardware V and V methodologies about common mode failure, commercial grade dedication process and electromagnetic compatibility. We have developed several guidelines, the software classification guideline, the quality assurance handbook for the software in digital I and C, the software V and V planning guideline, and the software safety guideline. And then, we have established the integrated environment for the safety-critical software based on the Computer Aided Software Engineering (CASE) tools. We have also surveyed a trend and application case of test facility for establishment of functional requirements. Input/output interface which connects among the host computer and developed target and panel are designed and manufactured using UXI bus. The developed functional test facility is used for test and validate the automatic start-up intelligent control system, the dynamic alarm system, the accident identification system using hidden Markov model, and the intelligent logic tracking system. The result of evaluation of the above systems shows the functional test facility performance is sufficient in normal operating and transient conditions. (author). 24 tabs., 59 figs

The development of advanced instrumentation and control technology. The development of verification and validation technology for instrumentation and control in NPPs

Energy Technology Data Exchange (ETDEWEB)

Kwon, Kee Choon; Ham, Chang Shik; Lee, Jang Soo; Kim, Jang Yeol; Song, Soon Ja; Kim, Jung Taek; Park, Won Man; Lee, Dong Young; Eom, Heung Seop; Park, Kee Yong

1997-07-01

We found essential problems followed by digitalizing of instrumentation and control. A scheme is divided into hardware and software to resolve these problems. We have analyzed the hardware V and V methodologies about common mode failure, commercial grade dedication process and electromagnetic compatibility. We have developed several guidelines, the software classification guideline, the quality assurance handbook for the software in digital I and C, the software V and V planning guideline, and the software safety guideline. And then, we have established the integrated environment for the safety-critical software based on the Computer Aided Software Engineering (CASE) tools. We have also surveyed a trend and application case of test facility for establishment of functional requirements. Input/output interface which connects among the host computer and developed target and panel are designed and manufactured using UXI bus. The developed functional test facility is used for test and validate the automatic start-up intelligent control system, the dynamic alarm system, the accident identification system using hidden Markov model, and the intelligent logic tracking system. The result of evaluation of the above systems shows the functional test facility performance is sufficient in normal operating and transient conditions. (author). 24 tabs., 59 figs.

Distributed Framework for Dynamic Telescope and Instrument Control

Science.gov (United States)

Ames, Troy J.; Case, Lynne

2002-01-01

Traditionally, instrument command and control systems have been developed specifically for a single instrument. Such solutions are frequently expensive and are inflexible to support the next instrument development effort. NASA Goddard Space Flight Center is developing an extensible framework, known as Instrument Remote Control (IRC) that applies to any kind of instrument that can be controlled by a computer. IRC combines the platform independent processing capabilities of Java with the power of the Extensible Markup Language (XML). A key aspect of the architecture is software that is driven by an instrument description, written using the Instrument Markup Language (IML). IML is an XML dialect used to describe graphical user interfaces to control and monitor the instrument, command sets and command formats, data streams, communication mechanisms, and data processing algorithms. The IRC framework provides the ability to communicate to components anywhere on a network using the JXTA protocol for dynamic discovery of distributed components. JXTA (see httD://www.jxta.org,) is a generalized protocol that allows any devices connected by a network to communicate in a peer-to-peer manner. IRC uses JXTA to advertise a device's IML and discover devices of interest on the network. Devices can join or leave the network and thus join or leave the instrument control environment of IRC. Currently, several astronomical instruments are working with the IRC development team to develop custom components for IRC to control their instruments. These instruments include: High resolution Airborne Wideband Camera (HAWC), a first light instrument for the Stratospheric Observatory for Infrared Astronomy (SOFIA); Submillimeter And Far Infrared Experiment (SAFIRE), a Principal Investigator instrument for SOFIA; and Fabry-Perot Interferometer Bolometer Research Experiment (FIBRE), a prototype of the SAFIRE instrument, used at the Caltech Submillimeter Observatory (CSO). Most recently, we have

Development of intelligent instruments with embedded HTTP servers for control and data acquisition in a cryogenic setup—The hardware, firmware, and software implementation

International Nuclear Information System (INIS)

Antony, Joby; Mathuria, D. S.; Datta, T. S.; Maity, Tanmoy

2015-01-01

The power of Ethernet for control and automation technology is being largely understood by the automation industry in recent times. Ethernet with HTTP (Hypertext Transfer Protocol) is one of the most widely accepted communication standards today. Ethernet is best known for being able to control through internet from anywhere in the globe. The Ethernet interface with built-in on-chip embedded servers ensures global connections for crate-less model of control and data acquisition systems which have several advantages over traditional crate-based control architectures for slow applications. This architecture will completely eliminate the use of any extra PLC (Programmable Logic Controller) or similar control hardware in any automation network as the control functions are firmware coded inside intelligent meters itself. Here, we describe the indigenously built project of a cryogenic control system built for linear accelerator at Inter University Accelerator Centre, known as “CADS,” which stands for “Complete Automation of Distribution System.” CADS deals with complete hardware, firmware, and software implementation of the automated linac cryogenic distribution system using many Ethernet based embedded cryogenic instruments developed in-house. Each instrument works as an intelligent meter called device-server which has the control functions and control loops built inside the firmware itself. Dedicated meters with built-in servers were designed out of ARM (Acorn RISC (Reduced Instruction Set Computer) Machine) and ATMEL processors and COTS (Commercially Off-the-Shelf) SMD (Surface Mount Devices) components, with analog sensor front-end and a digital back-end web server implementing remote procedure call over HTTP for digital control and readout functions. At present, 24 instruments which run 58 embedded servers inside, each specific to a particular type of sensor-actuator combination for closed loop operations, are now deployed and distributed across control LAN

Development of intelligent instruments with embedded HTTP servers for control and data acquisition in a cryogenic setup—The hardware, firmware, and software implementation

Energy Technology Data Exchange (ETDEWEB)

Antony, Joby; Mathuria, D. S.; Datta, T. S. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Maity, Tanmoy [Department of MME, Indian School of Mines (ISM), Dhanbad 826004 (India)

2015-12-15

The power of Ethernet for control and automation technology is being largely understood by the automation industry in recent times. Ethernet with HTTP (Hypertext Transfer Protocol) is one of the most widely accepted communication standards today. Ethernet is best known for being able to control through internet from anywhere in the globe. The Ethernet interface with built-in on-chip embedded servers ensures global connections for crate-less model of control and data acquisition systems which have several advantages over traditional crate-based control architectures for slow applications. This architecture will completely eliminate the use of any extra PLC (Programmable Logic Controller) or similar control hardware in any automation network as the control functions are firmware coded inside intelligent meters itself. Here, we describe the indigenously built project of a cryogenic control system built for linear accelerator at Inter University Accelerator Centre, known as “CADS,” which stands for “Complete Automation of Distribution System.” CADS deals with complete hardware, firmware, and software implementation of the automated linac cryogenic distribution system using many Ethernet based embedded cryogenic instruments developed in-house. Each instrument works as an intelligent meter called device-server which has the control functions and control loops built inside the firmware itself. Dedicated meters with built-in servers were designed out of ARM (Acorn RISC (Reduced Instruction Set Computer) Machine) and ATMEL processors and COTS (Commercially Off-the-Shelf) SMD (Surface Mount Devices) components, with analog sensor front-end and a digital back-end web server implementing remote procedure call over HTTP for digital control and readout functions. At present, 24 instruments which run 58 embedded servers inside, each specific to a particular type of sensor-actuator combination for closed loop operations, are now deployed and distributed across control LAN

SIMPATIQCO: a server-based software suite which facilitates monitoring the time course of LC-MS performance metrics on Orbitrap instruments.

Science.gov (United States)

Pichler, Peter; Mazanek, Michael; Dusberger, Frederico; Weilnböck, Lisa; Huber, Christian G; Stingl, Christoph; Luider, Theo M; Straube, Werner L; Köcher, Thomas; Mechtler, Karl

2012-11-02

While the performance of liquid chromatography (LC) and mass spectrometry (MS) instrumentation continues to increase, applications such as analyses of complete or near-complete proteomes and quantitative studies require constant and optimal system performance. For this reason, research laboratories and core facilities alike are recommended to implement quality control (QC) measures as part of their routine workflows. Many laboratories perform sporadic quality control checks. However, successive and systematic longitudinal monitoring of system performance would be facilitated by dedicated automatic or semiautomatic software solutions that aid an effortless analysis and display of QC metrics over time. We present the software package SIMPATIQCO (SIMPle AuTomatIc Quality COntrol) designed for evaluation of data from LTQ Orbitrap, Q-Exactive, LTQ FT, and LTQ instruments. A centralized SIMPATIQCO server can process QC data from multiple instruments. The software calculates QC metrics supervising every step of data acquisition from LC and electrospray to MS. For each QC metric the software learns the range indicating adequate system performance from the uploaded data using robust statistics. Results are stored in a database and can be displayed in a comfortable manner from any computer in the laboratory via a web browser. QC data can be monitored for individual LC runs as well as plotted over time. SIMPATIQCO thus assists the longitudinal monitoring of important QC metrics such as peptide elution times, peak widths, intensities, total ion current (TIC) as well as sensitivity, and overall LC-MS system performance; in this way the software also helps identify potential problems. The SIMPATIQCO software package is available free of charge.

Guidelines for evaluating software configuration management plans for digital instrumentation and control systems

International Nuclear Information System (INIS)

Cheon, Se Woo; Park, Jong Kyun; Lee, Ki Young; Lee, Jang Soo; Kim, Jang Yeon

2001-08-01

Software configuration management (SCM) is the process for identifying software configuration items (CIs), controlling the implementation and changes to software, recording and reporting the status of changes, and verifying the completeness and correctness of the released software. SCM consists of two major aspects: planning and implementation. Effective SCM involves planning for how activities are to be performed, and performing these activities in accordance with the Plan. This report first reviews the background of SCM that include key standards, SCM disciplines, SCM basic functions, baselines, software entity, SCM process, the implementation of SCM, and the tools of SCM. In turn, the report provides the guidelines for evaluating the SCM Plan for digital I and C systems of nuclear power plants. Most of the guidelines in the report are based on IEEE Std 828 and ANSI/IEEE Std 1042. According to BTP-14, NUREG-0800, the evaluation topics on the SCM Plan is classified into three categories: management, implementation, and resource characteristics

Design of software platform based on linux operating system for γ-spectrometry instrument

International Nuclear Information System (INIS)

Hong Tianqi; Zhou Chen; Zhang Yongjin

2008-01-01

This paper described the design of γ-spectrometry instrument software platform based on s3c2410a processor with arm920t core, emphases are focused on analyzing the integrated application of embedded linux operating system, yaffs file system and qt/embedded GUI development library. It presented a new software platform in portable instrument for γ measurement. (authors)

Verification and software validation for nuclear instrumentation

International Nuclear Information System (INIS)

Gaytan G, E.; Salgado G, J. R.; De Andrade O, E.; Ramirez G, A.

2014-10-01

In this work is presented a Verification Methodology and Software Validation, to be applied in instruments of nuclear use with associate software. This methodology was developed under the auspices of IAEA, through the regional projects RLA4022 (ARCAL XCIX) and RLA1011 (RLA CXXIII), led by Mexico. In the first project three plans and three procedures were elaborated taking into consideration IEEE standards, and in the second project these documents were updated considering ISO and IEC standards. The developed methodology has been distributed to the participant countries of Latin America in the ARCAL projects and two related courses have been imparted with the participation of several countries, and participating institutions of Mexico like Instituto Nacional de Investigaciones Nucleares (ININ), Comision Federal de Electricidad (CFE) and Comision Nacional de Seguridad Nuclear y Salvaguardias (CNSNS). In the ININ due to the necessity to work with Software Quality Guarantee in systems for the nuclear power plant of the CFE, a Software Quality Guarantee Plan and five procedures were developed in the year 2004, obtaining the qualification of the ININ for software development for the nuclear power plant of CFE. These first documents were developed taking like reference IEEE standards and regulator guides of NRC, being the first step for the development of the methodology. (Author)

On safety classification of instrumentation and control systems and their components

International Nuclear Information System (INIS)

Yastrebenetskij, M.A.; Rozen, Yu.V.

2004-01-01

Safety classification of instrumentation and control systems (I and C) and their components (hardware, software, software-hardware complexes) is described: - evaluation of classification principles and criteria in Ukrainian standards and rules; comparison between Ukrainian and international principles and criteria; possibility and ways of coordination of Ukrainian and international standards related to (I and C) safety classification

Simultaneous control of multiple instruments at the Advanced Technology Solar Telescope

Science.gov (United States)

Johansson, Erik M.; Goodrich, Bret

2012-09-01

The Advanced Technology Solar Telescope (ATST) is a 4-meter solar observatory under construction at Haleakala, Hawaii. The simultaneous use of multiple instruments is one of the unique capabilities that makes the ATST a premier ground based solar observatory. Control of the instrument suite is accomplished by the Instrument Control System (ICS), a layer of software between the Observatory Control System (OCS) and the instruments. The ICS presents a single narrow interface to the OCS and provides a standard interface for the instruments to be controlled. It is built upon the ATST Common Services Framework (CSF), an infrastructure for the implementation of a distributed control system. The ICS responds to OCS commands and events, coordinating and distributing them to the various instruments while monitoring their progress and reporting the status back to the OCS. The ICS requires no specific knowledge about the instruments. All information about the instruments used in an experiment is passed by the OCS to the ICS, which extracts and forwards the parameters to the appropriate instrument controllers. The instruments participating in an experiment define the active instrument set. A subset of those instruments must complete their observing activities in order for the experiment to be considered complete and are referred to as the must-complete instrument set. In addition, instruments may participate in eavesdrop mode, outside of the control of the ICS. All instrument controllers use the same standard narrow interface, which allows new instruments to be added without having to modify the interface or any existing instrument controllers.

The design of an instrument to evaluate software for EFL/ESL pronunciation teaching

Directory of Open Access Journals (Sweden)

Cristiana Gomes de Freitas Menezes Martins

2016-01-01

Full Text Available http://dx.doi.org/10.5007/2175-8026.2016v69n1p141 The purpose of this study was to develop and test the reliability and validity of an instrument to evaluate the extent to which software programs teach English as a Foreign Language and/or Second Language (EFL/ESL pronunciation following the principles of the Communicative Approach (Celce-Murcia et al, 2010, thus having the potential to develop English pronunciation. After the development of the instrument, 46 EFL/ESL teachers used it to analyze an online version of the software program Pronunciation Power 2. The responses of the participants were submitted to statistical analysis and the validity and reliability of the instrument were tested. The good reliability indexes obtained in this study suggest the instrument has some degree of validity for evaluating how well an ESL/EFL pronunciation teaching software program potentially develops English pronunciation.

Methods of software V and V for a programmable logic controller in NPPs

International Nuclear Information System (INIS)

Kim, Jang Yeol; Lee, Young Jun; Cha, Kyung Ho; Cheon, Se Woo; Son, Han Seong; Lee, Jang Soo; Kwon, Kee Choon

2004-01-01

This paper addresses the Verification and Validation (V and V) process and methodology for embedded real time software of a safety-grade Programmable Logic Controller(PLC). This safety-grade PLC is being developed in the Korea Nuclear Instrumentation and Control System (KNICS) projects. KNICS projects are developing a Reactor Protection System(RPS) and an Engineered Safety Feature-Component Control System (ESF-CCS) as well as safety-grade PLC. Safety-grade PLC will be a major component that composes the RPS systems and ESF-CCS systems as nuclear instruments and control equipments. This paper describes the V and V guidelines and procedure, V and V environment, V and V process and methodology, and the V and V tools by the KNICS projects. Specially, it describes the real-time operating system V and V experience which corresponds to the requirement analysis phase of the software development life cycle. Main activities of the real-time operating system Software Requirement Specification(SRS) V and V of the PLC are the technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, software safety analysis, and software configuration management. The proposed V and V methodology satisfies the Standard Review Plan(SRP)/Branch Technical Position(BTP)-14(MOST-KSRG 7/Appendix 15 in Korea will be issued soon) criteria for the safety software in nuclear power plants. The proposed V and V methodology is going to verify the upcoming software life cycle in the KNICS projects. (author)

Final Technical Report on Quantifying Dependability Attributes of Software Based Safety Critical Instrumentation and Control Systems in Nuclear Power Plants

International Nuclear Information System (INIS)

Smidts, Carol; Huang, Fuqun; Li, Boyuan; Li, Xiang

2016-01-01

With the current transition from analog to digital instrumentation and control systems in nuclear power plants, the number and variety of software-based systems have significantly increased. The sophisticated nature and increasing complexity of software raises trust in these systems as a significant challenge. The trust placed in a software system is typically termed software dependability. Software dependability analysis faces uncommon challenges since software systems' characteristics differ from those of hardware systems. The lack of systematic science-based methods for quantifying the dependability attributes in software-based instrumentation as well as control systems in safety critical applications has proved itself to be a significant inhibitor to the expanded use of modern digital technology in the nuclear industry. Dependability refers to the ability of a system to deliver a service that can be trusted. Dependability is commonly considered as a general concept that encompasses different attributes, e.g., reliability, safety, security, availability and maintainability. Dependability research has progressed significantly over the last few decades. For example, various assessment models and/or design approaches have been proposed for software reliability, software availability and software maintainability. Advances have also been made to integrate multiple dependability attributes, e.g., integrating security with other dependability attributes, measuring availability and maintainability, modeling reliability and availability, quantifying reliability and security, exploring the dependencies between security and safety and developing integrated analysis models. However, there is still a lack of understanding of the dependencies between various dependability attributes as a whole and of how such dependencies are formed. To address the need for quantification and give a more objective basis to the review process -- therefore reducing regulatory uncertainty

Final Technical Report on Quantifying Dependability Attributes of Software Based Safety Critical Instrumentation and Control Systems in Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Smidts, Carol [The Ohio State Univ., Columbus, OH (United States); Huang, Funqun [The Ohio State Univ., Columbus, OH (United States); Li, Boyuan [The Ohio State Univ., Columbus, OH (United States); Li, Xiang [The Ohio State Univ., Columbus, OH (United States)

2016-03-25

With the current transition from analog to digital instrumentation and control systems in nuclear power plants, the number and variety of software-based systems have significantly increased. The sophisticated nature and increasing complexity of software raises trust in these systems as a significant challenge. The trust placed in a software system is typically termed software dependability. Software dependability analysis faces uncommon challenges since software systems’ characteristics differ from those of hardware systems. The lack of systematic science-based methods for quantifying the dependability attributes in software-based instrumentation as well as control systems in safety critical applications has proved itself to be a significant inhibitor to the expanded use of modern digital technology in the nuclear industry. Dependability refers to the ability of a system to deliver a service that can be trusted. Dependability is commonly considered as a general concept that encompasses different attributes, e.g., reliability, safety, security, availability and maintainability. Dependability research has progressed significantly over the last few decades. For example, various assessment models and/or design approaches have been proposed for software reliability, software availability and software maintainability. Advances have also been made to integrate multiple dependability attributes, e.g., integrating security with other dependability attributes, measuring availability and maintainability, modeling reliability and availability, quantifying reliability and security, exploring the dependencies between security and safety and developing integrated analysis models. However, there is still a lack of understanding of the dependencies between various dependability attributes as a whole and of how such dependencies are formed. To address the need for quantification and give a more objective basis to the review process -- therefore reducing regulatory uncertainty

The UP3-UP2 800 reprocessing plants control systems. Use of tools for the diagnosis, the track of control softwares and the management of technical data

International Nuclear Information System (INIS)

Chabert, J.; Michon, J.C.

1995-01-01

After a rapid presentation of control systems architectures of the La Hague COGEMA reprocessing plants, details are given about the tools used to master the control and instrumentation softwares and technical data. The paper focusses more particularly on the CML (Software Maintenance Center) tool which manages the software versions installed on the driving system, on the SYDDEX tool devoted to the management of the control and instrumentation associated data and documents, and on the SAD tool used for diagnosis assistance. (J.S.). 5 figs

A software simulator for the SPICA Safari instrument

International Nuclear Information System (INIS)

Naylor, D A; Hayton, D J; Lindner, J V; Sadeghi, B

2011-01-01

A software simulator that has been developed for the Safari instrument proposed for the SPace Infrared telescope for Cosmology and Astrophysics (SPICA) mission is presented. The simulator can ingest a range of realistic input spectra and, following a thorough radiative transfer analysis, calculates the power reaching the detector as a function of the optical path difference within the interferometer. The simulator is modular in design so that it can be easily modified to ingest test data as they become available. The simulator will not only find use during the design phase of the Safari instrument, but also during ground performance verification campaigns of the flight model. Through validation of the simulator on ground test data, it will be possible to predict accurately the in-orbit performance of the Safari instrument

Software design specification and analysis(NuFDS) approach for the safety critical software based on porgrammable logic controller(PLC)

International Nuclear Information System (INIS)

Koo, Seo Ryong; Seong, Poong Hyun; Jung, Jin Yong; Choi, Seong Soo

2004-01-01

This paper introduces the software design specification and analysis technique for the safety-critical system based on Programmable Logic Controller (PLC). During software development phases, the design phase should perform an important role to connect between requirements phase and implementation phase as a process of translating problem requirements into software structures. In this work, the Nuclear FBD-style Design Specification and analysis (NuFDS) approach was proposed. The NuFDS approach for nuclear Instrumentation and Control (I and C) software are suggested in a straight forward manner. It consists of four major specifications as follows; Database, Software Architecture, System Behavior, and PLC Hardware Configuration. Additionally, correctness, completeness, consistency, and traceability check techniques are also suggested for the formal design analysis in NuFDS approach. In addition, for the tool supporting, we are developing NuSDS tool based on the NuFDS approach which is a tool, especially for the software design specification in nuclear fields

Software and control system for the VLT Survey Telescope

International Nuclear Information System (INIS)

Schipani, P; Marty, L; Dall'Ora, M; D'Orsi, S; Argomedo, J; Arcidiacono, C; Farinato, J; Magrin, D; Ragazzoni, R; Umbriaco, G

2013-01-01

The VLT Survey Telescope (VST) has started the regular operations in 2011 after a successful commissioning at Cerro Paranal (Chile), the site which hosts the best facilities for optical astronomy operated by the European Southern Observatory (ESO). After a short description of the instrument, this paper mainly focuses on the telescope control software, which is in charge of the real-time control of the hardware and of the overall coordination of the operations, including pointing and tracking, active optics and presets. We describe the main features of the software implementation in the context of the ESO observatory standards, and the goals reached during the commissioning phase and in the first year of operations.

A Calculation of hydrodynamic noise of control valve on instrumentation and control system using smart plant

International Nuclear Information System (INIS)

Demon Handoyo; Djoko H Nugroho

2012-01-01

It has been calculated characteristics of the control valve Instrumentation and Control Systems using Smart Plant software. This calculation is done in order to control the valve that will be installed as part of the instrumentation and control systems to provide the performance according to the design. The characteristics that have been calculated are Reynolds number factors which are related to the flow regime in the valve. Critical pressure factor, Valve Hydrodynamic cavitation and noise index. In this paper the discussion will be limited to matters relating to Hydrodynamic noise generation process using model of the instrumentation and control system in the plant design in yellow cake PIPKPP activities in 2012. The results of the calculation of the noise on the valves design are in the range between 9.58~70.1 dBA. (author)

V and V methods of a safety-critical software for a programmable logic controller

Energy Technology Data Exchange (ETDEWEB)

Kim, Jang Yeol; Lee, Young Jun; Cha, Kyung Ho; Cheon, Se Woo; Lee, Jang Soo; Kwon, Kee Choon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kong, Seung Ju [Korea Hydro and Nuclear Power Co., Ltd, Daejeon (Korea, Republic of)

2005-11-15

This paper addresses the Verification an Validation(V and V) process and the methodology for an embedded real time software of a safety-grade Programmable Logic Controller(PLC). This safety-grade PLC is being developed as one of the Korean Nuclear Instrumentation and Control System(KNICS) project KNICS projects are developing a Reactor Protection System(RPS) and an Engineered Safety Feature-Component Control System(ESF-CCS) as well as a safety-grade PLC. The safety-grade PLC will be a major component that encomposes the RPS systems and the ESF-CCS systems as nuclear instruments and control equipment. This paper describes the V and V guidelines an procedures, V and V environment, V and V process and methodology, and the V and V tools in the KNICS projects. Specifically, it describes the real-time operating system V and V experience which corresponds to the requirement analysis phase, design phase and the implementation and testing phase of the software development life cycle. Main activities of the V and V for the PLC system software are a technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, software safety analysis, and a software configuration management. The proposed V and V methodology satisfies the Standard Review Plan(SRP)/Branch Technical Position(BTP)-14 criteria for the safety software in nuclear power plants. The proposed V and V methodology is going to be used to verify the upcoming software life cycle in the KNICS projects.

V and V methods of a safety-critical software for a programmable logic controller

International Nuclear Information System (INIS)

Kim, Jang Yeol; Lee, Young Jun; Cha, Kyung Ho; Cheon, Se Woo; Lee, Jang Soo; Kwon, Kee Choon; Kong, Seung Ju

2005-01-01

This paper addresses the Verification an Validation(V and V) process and the methodology for an embedded real time software of a safety-grade Programmable Logic Controller(PLC). This safety-grade PLC is being developed as one of the Korean Nuclear Instrumentation and Control System(KNICS) project KNICS projects are developing a Reactor Protection System(RPS) and an Engineered Safety Feature-Component Control System(ESF-CCS) as well as a safety-grade PLC. The safety-grade PLC will be a major component that encomposes the RPS systems and the ESF-CCS systems as nuclear instruments and control equipment. This paper describes the V and V guidelines an procedures, V and V environment, V and V process and methodology, and the V and V tools in the KNICS projects. Specifically, it describes the real-time operating system V and V experience which corresponds to the requirement analysis phase, design phase and the implementation and testing phase of the software development life cycle. Main activities of the V and V for the PLC system software are a technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, software safety analysis, and a software configuration management. The proposed V and V methodology satisfies the Standard Review Plan(SRP)/Branch Technical Position(BTP)-14 criteria for the safety software in nuclear power plants. The proposed V and V methodology is going to be used to verify the upcoming software life cycle in the KNICS projects

Flexible software architecture for user-interface and machine control in laboratory automation.

Science.gov (United States)

Arutunian, E B; Meldrum, D R; Friedman, N A; Moody, S E

1998-10-01

We describe a modular, layered software architecture for automated laboratory instruments. The design consists of a sophisticated user interface, a machine controller and multiple individual hardware subsystems, each interacting through a client-server architecture built entirely on top of open Internet standards. In our implementation, the user-interface components are built as Java applets that are downloaded from a server integrated into the machine controller. The user-interface client can thereby provide laboratory personnel with a familiar environment for experiment design through a standard World Wide Web browser. Data management and security are seamlessly integrated at the machine-controller layer using QNX, a real-time operating system. This layer also controls hardware subsystems through a second client-server interface. This architecture has proven flexible and relatively easy to implement and allows users to operate laboratory automation instruments remotely through an Internet connection. The software architecture was implemented and demonstrated on the Acapella, an automated fluid-sample-processing system that is under development at the University of Washington.

Void fraction instrument software, Version 1,2, Acceptance test report

International Nuclear Information System (INIS)

Gimera, M.

1995-01-01

This provides the report for the void fraction instrument acceptance test software Version 1.2. The void fraction will collect data that will be used to calculate the quantity of gas trapped in waste tanks

Application range affected by software failures in safety relevant instrumentation and control systems of nuclear power plants; Auswirkungsbereiche von Softwarefehlern in sicherheitstechnisch wichtigen Einrichtungen von Kernkraftwerken

Energy Technology Data Exchange (ETDEWEB)

Jopen, Manuela; Mbonjo, Herve; Sommer, Dagmar; Ulrich, Birte

2017-03-15

This report presents results that have been developed within a BMUB-funded research project (Promotion Code 3614R01304). The overall objective of this project was to broaden the knowledge base of GRS regarding software failures and their impact in software-based instrumentation and control (I and C) systems. To this end, relevant definitions and terms in standards and publications (DIN, IEEE standards, IAEA standards, NUREG publications) as well as in the German safety requirements for nuclear power plants were analyzed first. In particular, it was found that the term ''software fault'' is defined differently and partly contradictory in the considered literature sources. For this reason, a definition of software fault was developed on the basis of the software life cycle of software-based I and C systems within the framework of this project, which takes into account the various aspects relevant to software faults and their related effects. It turns out that software failures result from latent faults in a software-based control system, which can lead to a non-compliant behavior of a software-based I and C system. Hereby a distinction should be made between programming faults and specification faults. In a further step, operational experience with software failures in software-based I and C systems in nuclear facilities and in nonnuclear sector was investigated. The identified events were analyzed with regard to their cause and impacts and the analysis results were summarized. Based on the developed definition of software failure and on the COMPSIS-classification scheme for events related to software based I and C systems, the COCS-classification scheme was developed to classify events from operating experience with software failures, in which the events are classified according to the criteria ''cause'', ''affected system'', ''impact'' and ''CCF potential''. This

Design and development of control instrumentation for the superconducting Linear Accelerator

International Nuclear Information System (INIS)

Joshi, Gopal; Kapatral, R.S.; Jha, K.; Rathod, N.C.; Sujo, C.I.; Ananthakrishnan, T.S.; Narsaiah, A.; Ghodgaonkar, M.D.; Kataria, S.K.; Singh, S.K.

2001-01-01

Electronics Division, BARC is developing the required control instrumentation for the Linear Accelerator (LINAC) coming up at TIFR. This consists of RF systems, CAMAC instruments and the Control and Information System. The control system consists of several identical Local Control Stations (LCS) connected over a LAN to a Main Control Station (MCS). Each LCS consists of a PC, CAMAC crates with functional Modules and RF systems. The MCS will contain two PCs running identical software. Each LCS will cater to two LINAC module each consisting of one cryostat and four resonators. This paper discusses different systems developed and under development in the Electronics Division which play an important role in the control of the LINAC. (author)

Implementation of a communication and control network for the instruments of a nuclear analytical laboratory

International Nuclear Information System (INIS)

Cunya, Eduardo; Baltuano, Oscar; Bedregal, Patricia

2013-01-01

This paper describes the implementation of a communication network and control for a conventional laboratory instruments and nuclear analytical processes based on CAN open field bus to control devices and machines. Hardware components and software developed as well as installation and configuration tools for incorporating new instruments to the network re presented. (authors).

Declarative flow control for distributed instrumentation

Energy Technology Data Exchange (ETDEWEB)

Parvin, Bahram; Taylor, John; Fontenay, Gerald; Callahan, Daniel

2001-06-01

We have developed a 'microscopy channel' to advertise a unique set of on-line scientific instruments and to let users join a particular session, perform an experiment, collaborate with other users, and collect data for further analysis. The channel is a collaborative problem solving environment (CPSE) that allows for both synchronous and asynchronous collaboration, as well as flow control for enhanced scalability. The flow control is a declarative feature that enhances software functionality at the experimental scale. Our testbed includes several unique electron and optical microscopes with applications ranging from material science to cell biology. We have built a system that leverages current commercial CORBA services, Web Servers, and flow control specifications to meet diverse requirements for microscopy and experimental protocols. In this context, we have defined and enhanced Instrument Services (IS), Exchange Services (ES), Computational Services (CS), and Declarative Services (DS) that sit on top of CORBA and its enabling services (naming, trading, security, and notification) IS provides a layer of abstraction for controlling any type of microscope. ES provides a common set of utilities for information management and transaction. CS provides the analytical capabilities needed for online microscopy. DS provides mechanisms for flow control for improving the dynamic behavior of the system.

Design of virtual three-dimensional instruments for sound control

Science.gov (United States)

Mulder, Axel Gezienus Elith

An environment for designing virtual instruments with 3D geometry has been prototyped and applied to real-time sound control and design. It enables a sound artist, musical performer or composer to design an instrument according to preferred or required gestural and musical constraints instead of constraints based only on physical laws as they apply to an instrument with a particular geometry. Sounds can be created, edited or performed in real-time by changing parameters like position, orientation and shape of a virtual 3D input device. The virtual instrument can only be perceived through a visualization and acoustic representation, or sonification, of the control surface. No haptic representation is available. This environment was implemented using CyberGloves, Polhemus sensors, an SGI Onyx and by extending a real- time, visual programming language called Max/FTS, which was originally designed for sound synthesis. The extension involves software objects that interface the sensors and software objects that compute human movement and virtual object features. Two pilot studies have been performed, involving virtual input devices with the behaviours of a rubber balloon and a rubber sheet for the control of sound spatialization and timbre parameters. Both manipulation and sonification methods affect the naturalness of the interaction. Informal evaluation showed that a sonification inspired by the physical world appears natural and effective. More research is required for a natural sonification of virtual input device features such as shape, taking into account possible co- articulation of these features. While both hands can be used for manipulation, left-hand-only interaction with a virtual instrument may be a useful replacement for and extension of the standard keyboard modulation wheel. More research is needed to identify and apply manipulation pragmatics and movement features, and to investigate how they are co-articulated, in the mapping of virtual object

Instrumentation and control of the Doublet III Neutral Beam Injector System

Energy Technology Data Exchange (ETDEWEB)

Kohli, J.C.; Moore, C.D.; Drobnis, D.D.; Elischer, V.P.; Kilgore, R.; Uber, D.

1980-03-01

The hardware and software required for the operation of the Doublet III Neutral Beam Injector System (NBIS) are described. Development and implementation of this Instrumentation and Control System was divided between the major participants - General Atomic Company and Lawrence Berkeley Laboratory. The subdivision of responsibilities and the coordination of the participants' activities are described with reference to hardware and software requirements in support of the entire system. Included are a description of the operators' consoles, the interlock system and the CAMAC system. One feature of the control software is source modeling. This feature includes feedback on a shot to shot basis and adaptive control. Adaptive control permits the computer system to automatically adjust parameters after a shot, and to control the system to automatically compensate for time varying NBIS components. The Neutral Beam Power Supply features power supply modeling, fiber optic transmission of analog signals and digital control of power supply power-up/interlocks.

Instrumentation and control of the Doublet III Neutral Beam Injector System

International Nuclear Information System (INIS)

Kohli, J.C.; Moore, C.D.; Drobnis, D.D.; Elischer, V.P.; Kilgore, R.; Uber, D.

1980-03-01

The hardware and software required for the operation of the Doublet III Neutral Beam Injector System (NBIS) are described. Development and implementation of this Instrumentation and Control System was divided between the major participants - General Atomic Company and Lawrence Berkeley Laboratory. The subdivision of responsibilities and the coordination of the participants' activities are described with reference to hardware and software requirements in support of the entire system. Included are a description of the operators' consoles, the interlock system and the CAMAC system. One feature of the control software is source modeling. This feature includes feedback on a shot to shot basis and adaptive control. Adaptive control permits the computer system to automatically adjust parameters after a shot, and to control the system to automatically compensate for time varying NBIS components. The Neutral Beam Power Supply features power supply modeling, fiber optic transmission of analog signals and digital control of power supply power-up/interlocks

Instrumentation and Controls Division, Technical Support Department Management Plan, FY 1993--FY 1996

Energy Technology Data Exchange (ETDEWEB)

Adkisson, B.P.; Kunselman, C.W.; Effler, R.P.; Miller, D.R.; Millet, A.J.; Stansberry, C.T.

1993-08-01

This report describes the organization, key functions, and major activities of the Technical Support Department The Department is the programmatic support element of the Instrumentation and Controls Division. The Department`s primary focus is the support of existing equipment and systems at Oak Ridge National Laboratory that are generally characterized as instrumentation and controls. The support takes the form of repair, calibration, fabrication, field engineering, preventive maintenance, software support, and record keeping.

CARMENES instrument control system and operational scheduler

Science.gov (United States)

Garcia-Piquer, Alvaro; Guàrdia, Josep; Colomé, Josep; Ribas, Ignasi; Gesa, Lluis; Morales, Juan Carlos; Pérez-Calpena, Ana; Seifert, Walter; Quirrenbach, Andreas; Amado, Pedro J.; Caballero, José A.; Reiners, Ansgar

2014-07-01

The main goal of the CARMENES instrument is to perform high-accuracy measurements of stellar radial velocities (1m/s) with long-term stability. CARMENES will be installed in 2015 at the 3.5 m telescope in the Calar Alto Observatory (Spain) and it will be equipped with two spectrographs covering from the visible to the near-infrared. It will make use of its near-IR capabilities to observe late-type stars, whose peak of the spectral energy distribution falls in the relevant wavelength interval. The technology needed to develop this instrument represents a challenge at all levels. We present two software packages that play a key role in the control layer for an efficient operation of the instrument: the Instrument Control System (ICS) and the Operational Scheduler. The coordination and management of CARMENES is handled by the ICS, which is responsible for carrying out the operations of the different subsystems providing a tool to operate the instrument in an integrated manner from low to high user interaction level. The ICS interacts with the following subsystems: the near-IR and visible channels, composed by the detectors and exposure meters; the calibration units; the environment sensors; the front-end electronics; the acquisition and guiding module; the interfaces with telescope and dome; and, finally, the software subsystems for operational scheduling of tasks, data processing, and data archiving. We describe the ICS software design, which implements the CARMENES operational design and is planned to be integrated in the instrument by the end of 2014. The CARMENES operational scheduler is the second key element in the control layer described in this contribution. It is the main actor in the translation of the survey strategy into a detailed schedule for the achievement of the optimization goals. The scheduler is based on Artificial Intelligence techniques and computes the survey planning by combining the static constraints that are known a priori (i.e., target

Study on virtual instrument developing system based on intelligent virtual control

International Nuclear Information System (INIS)

Tang Baoping; Cheng Fabin; Qin Shuren

2005-01-01

The paper introduces a non-programming developing system of a virtual instrument (VI), i.e., a virtual measurement instrument developing system (VMIDS) based on intelligent virtual control (IVC). The background of the IVC-based VMIDS is described briefly, and the hierarchical message bus (HMB)-based software architecture of VMIDS is discussed in detail. The three parts and functions of VMIDS are introduced, and the process of non-programming developing VI is further described

Study on virtual instrument developing system based on intelligent virtual control

Energy Technology Data Exchange (ETDEWEB)

Tang Baoping; Cheng Fabin; Qin Shuren [Test Center, College of Mechanical Engineering, Chongqing University , Chongqing 400030 (China)

2005-01-01

The paper introduces a non-programming developing system of a virtual instrument (VI), i.e., a virtual measurement instrument developing system (VMIDS) based on intelligent virtual control (IVC). The background of the IVC-based VMIDS is described briefly, and the hierarchical message bus (HMB)-based software architecture of VMIDS is discussed in detail. The three parts and functions of VMIDS are introduced, and the process of non-programming developing VI is further described.

State-of-the-art report for the instrumentation and control technology based on the nuclear-information technology convergence

International Nuclear Information System (INIS)

Kwon, Kee Choon; Kim, Chang Hwoi; Lee, Dong Young; Lee, Cheol Kwon; Lee, Hyun Chul

2011-12-01

As digitalized the instrumentation and control systems in nuclear power plants, in the past that were implemented in an analog system or circuit for monitoring, control and protection, most of the them is implemented in embedded software based on hardware platform. Digital instrumentation and control system hardware platforms and a digital safety systems have developed in Korea. The fundamental technology of the software part of MMIS (Man-Machine Interface System) has achieved the localization. But in order to secure our global competitiveness, in the -based software, the source of the content areas / It is needed to develop core technologies of the software and contents areas based on the nuclear-IT convergence technology. In this report, the IT technology centered for the characteristics of embedded software applied to nuclear power is described. Also state-of-the-art IT technologies that will converge to nuclear power plants are mentioned

An integrated software testing framework for FGA-based controllers in nuclear power plants

International Nuclear Information System (INIS)

Kim, Jae Yeob; Kim, Eun Sub; Yoo, Jun Beom; Lee, Young Jun; Choi, Jong Gyun

2016-01-01

Field-programmable gate arrays (FPGAs) have received much attention from the nuclear industry as an alternative platform to programmable logic controllers for digital instrumentation and control. The software aspect of FPGA development consists of several steps of synthesis and refinement, and also requires verification activities, such as simulations that are performed individually at each step. This study proposed an integrated software-testing framework for simulating all artifacts of the FPGA software development simultaneously and evaluating whether all artifacts work correctly using common oracle programs. This method also generates a massive number of meaningful simulation scenarios that reflect reactor shutdown logics. The experiment, which was performed on two FPGA software implementations, showed that it can dramatically save both time and costs

Development of DC-TOF control software framework

International Nuclear Information System (INIS)

Kim, Hong Joo; Kim, Hyun Ok

2010-06-01

Disk-Chopper Time-of-Flight spectrometer (DC-TOF) is a new cold neutron instrument under construction at the Korea Atomic Energy Research Institute (KAERI). It will be equipped with a total of 352 2m PSDs(Position Sensitive Detectors), which are grouped into 11 panels. We developed the main DAQ/Control software works well between multi-DSPs of electronics and user. It is convenient to operate DC-TOF system and monitor it's data quality using GUI(Graphical User Interface). Also it satisfies design throughout with test result of 100K events/s

New Control Software of the 188cm Telescope of Okayama Astrophysical Observatory

Science.gov (United States)

Yoshida, Michitoshi; Shimizu, Yasuhiro; Watanabe, Etsuji; Yanagisawa, Kenshi; Uraguchi, Fumihiro

2002-12-01

We developed the telescope control software for the 188cm telescope of Okayama Astrophysical Observatory (OAO) based on Java technology. Basically, the software consists of two processes running on separate Java virtual machines; one of which is the "Command Dispatcher (CD)" and the other is the "User Interface (UI)". Among the two, CD is the main engine/server of the telescope control, whereas UI is just a client. The "standard" UI we provide is a graphical user interface written in Java/Swing. CD communicates with the local control units (LCUs) of the telescope through RS232C. CD is a Java multi-thread program, in which a number of threads run simultaneously. The threads running in CD are the follows: UNIX socket servers for external communications, socket opener for on-demand open/close of a socket port, socket client manager, auto-guider and dome watcher, internal command dispatcher, status manager, status collector, RS232C writer and reader, logger, and control units. The above "control units" are software models ("objects") of the telescope system. We introduced four control units- "Telescope", "Dome", "Weather-Monitor", and "Pointing"- for telescope control. The first three units are simple software models of the real-worlds devices. The last one, "Pointing", is a unit which abstracts pointing procedure of the telescope. CD and UI communicate with each other using UNIX socket. The command protocol of this communication is fairly simple, and observation instruments, auto guider, or additional UI for remote observation are also able to communicate with CD through socket using this protocol. CD opens and closes socket ports for communication on demand according to the request of client process (UI, instruments etc.), so that any clients can be connected to CD dynamically.

Use of modern software - based instrumentation in safety critical systems

International Nuclear Information System (INIS)

Emmett, J.; Smith, B.

2005-01-01

Many Nuclear Power Plants are now ageing and in need of various degrees of refurbishment. Installed instrumentation usually uses out of date 'analogue' technology and is often no longer available in the market place. New technology instrumentation is generally un-qualified for nuclear use and specifically the new 'smart' technology contains 'firmware', (effectively 'soup' (Software of Uncertain Pedigree)) which must be assessed in accordance with relevant safety standards before it may be used in a safety application. Particular standards are IEC 61508 [1] and the British Energy (BE) PES (Programmable Electronic Systems) guidelines EPD/GEN/REP/0277/97. [2] This paper outlines a new instrument evaluation system, which has been developed in conjunction with the UK Nuclear Industry. The paper concludes with a discussion about on-line monitoring of Smart instrumentation in safety critical applications. (author)

Research and Implementation of Software Used for the Remote Control for VM700T Video Measuring Instrument

Directory of Open Access Journals (Sweden)

Song Wenjie

2015-01-01

Full Text Available In this paper, the measurement software which can be used to realize remote control of the VM700T video measuring instrument is introduced. The authors can operate VM700T by a virtual panel on the client computer, select the results that the measuring equipment displayed to transmit it, and then display the image on the VM700T virtual panel in real time. The system does have some practical values and play an important role in distance learning. The functions that the system realized mainly includes four aspects: the real-time transmission of message based on the socket technology, the serial connection between server PC and VM700T measuring equipment, the image acquisition based on VFW technology and JPEG compression and decompression, and the network transmission of image files. The actual network transmission test is shown that the data acquisition method of this thesis is flexible and convenient, and the system is of extraordinary stability. It can display the measurement results in real time and basically realize the requirements of remote control. In the content, this paper includes a summary of principle, the detailed introduction of the system realization process and some related technology.

The Software Design for the Wide-Field Infrared Explorer Attitude Control System

Science.gov (United States)

Anderson, Mark O.; Barnes, Kenneth C.; Melhorn, Charles M.; Phillips, Tom

1998-01-01

The Wide-Field Infrared Explorer (WIRE), currently scheduled for launch in September 1998, is the fifth of five spacecraft in the NASA/Goddard Small Explorer (SMEX) series. This paper presents the design of WIRE's Attitude Control System flight software (ACS FSW). WIRE is a momentum-biased, three-axis stabilized stellar pointer which provides high-accuracy pointing and autonomous acquisition for eight to ten stellar targets per orbit. WIRE's short mission life and limited cryogen supply motivate requirements for Sun and Earth avoidance constraints which are designed to prevent catastrophic instrument damage and to minimize the heat load on the cryostat. The FSW implements autonomous fault detection and handling (FDH) to enforce these instrument constraints and to perform several other checks which insure the safety of the spacecraft. The ACS FSW implements modules for sensor data processing, attitude determination, attitude control, guide star acquisition, actuator command generation, command/telemetry processing, and FDH. These software components are integrated with a hierarchical control mode managing module that dictates which software components are currently active. The lowest mode in the hierarchy is the 'safest' one, in the sense that it utilizes a minimal complement of sensors and actuators to keep the spacecraft in a stable configuration (power and pointing constraints are maintained). As higher modes in the hierarchy are achieved, the various software functions are activated by the mode manager, and an increasing level of attitude control accuracy is provided. If FDH detects a constraint violation or other anomaly, it triggers a safing transition to a lower control mode. The WIRE ACS FSW satisfies all target acquisition and pointing accuracy requirements, enforces all pointing constraints, provides the ground with a simple means for reconfiguring the system via table load, and meets all the demands of its real-time embedded environment (16 MHz Intel

Integrated conception of hardware/software mixed systems used in nuclear instrumentation

International Nuclear Information System (INIS)

Dias, Ailton F.; Sorel, Yves; Akil, Mohamed

2002-01-01

Hardware/software codesign carries out the design of systems composed by a hardware portion, with specific components, and a software portion, with microprocessor based architecture. This paper describes the Algorithm Architecture Adequation (AAA) design methodology - originally oriented to programmable multicomponent architectures, its extension to reconfigurable circuits and its application to design and development of nuclear instrumentation systems composed by programmable and configurable circuits. AAA methodology uses an unified model to describe algorithm, architecture and implementation, based on graph theory. The great advantage of AAA methodology is the utilization of a same model from the specification to the implementation of hardware/software systems, reducing the complexity and design time. (author)

Runtime Instrumentation of SystemC/TLM2 Interfaces for Fault Tolerance Requirements Verification in Software Cosimulation

Directory of Open Access Journals (Sweden)

Antonio da Silva

2014-01-01

Full Text Available This paper presents the design of a SystemC transaction level modelling wrapping library that can be used for the assertion of system properties, protocol compliance, or fault injection. The library uses C++ virtual table hooks as a dynamic binary instrumentation technique to inline wrappers in the TLM2 transaction path. This technique can be applied after the elaboration phase and needs neither source code modifications nor recompilation of the top level SystemC modules. The proposed technique has been successfully applied to the robustness verification of the on-board boot software of the Instrument Control Unit of the Solar Orbiter’s Energetic Particle Detector.

[Controlling instruments in radiology].

Science.gov (United States)

Maurer, M

2013-10-01

Due to the rising costs and competitive pressures radiological clinics and practices are now facing, controlling instruments are gaining importance in the optimization of structures and processes of the various diagnostic examinations and interventional procedures. It will be shown how the use of selected controlling instruments can secure and improve the performance of radiological facilities. A definition of the concept of controlling will be provided. It will be shown which controlling instruments can be applied in radiological departments and practices. As an example, two of the controlling instruments, material cost analysis and benchmarking, will be illustrated.

Software design for the VIS instrument onboard the Euclid mission: a multilayer approach

Science.gov (United States)

Galli, E.; Di Giorgio, A. M.; Pezzuto, S.; Liu, S. J.; Giusi, G.; Li Causi, G.; Farina, M.; Cropper, M.; Denniston, J.; Niemi, S.

2014-07-01

The Euclid mission scientific payload is composed of two instruments: a VISible Imaging Instrument (VIS) and a Near Infrared Spectrometer and Photometer instrument (NISP). Each instrument has its own control unit. The Instrument Command and Data Processing Unit (VI-CDPU) is the control unit of the VIS instrument. The VI-CDPU is connected directly to the spacecraft by means of a MIL-STD-1553B bus and to the satellite Mass Memory Unit via a SpaceWire link. All the internal interfaces are implemented via SpaceWire links and include 12 high speed lines for the data provided by the 36 focal plane CCDs readout electronics (ROEs) and one link to the Power and Mechanisms Control Unit (VI-PMCU). VI-CDPU is in charge of distributing commands to the instrument sub-systems, collecting their housekeeping parameters and monitoring their health status. Moreover, the unit has the task of acquiring, reordering, compressing and transferring the science data to the satellite Mass Memory. This last feature is probably the most challenging one for the VI-CDPU, since stringent constraints about the minimum lossless compression ratio, the maximum time for the compression execution and the maximum power consumption have to be satisfied. Therefore, an accurate performance analysis at hardware layer is necessary, which could delay too much the design and development of software. In order to mitigate this risk, in the multilayered design of software we decided to design a middleware layer that provides a set of APIs with the aim of hiding the implementation of the HW connected layer to the application one. The middleware is built on top of the Operating System layer (which includes the Real-Time OS that will be adopted) and the onboard Computer Hardware. The middleware itself has a multi-layer architecture composed of 4 layers: the Abstract RTOS Adapter Layer (AOSAL), the Speci_c RTOS Adapter Layer (SOSAL), the Common Patterns Layer (CPL), the Service Layer composed of two subgroups which

Verification and software validation for nuclear instrumentation; Verificacion y validacion de software para instrumentacion nuclear

Energy Technology Data Exchange (ETDEWEB)

Gaytan G, E. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Salgado G, J. R. [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan No. 779, Col. Narvarte, 03020 Mexico D. F. (Mexico); De Andrade O, E. [Universidad Federal de Rio de Janeiro, Caixa Postal 68509, 21945-970 Rio de Janeiro (Brazil); Ramirez G, A., E-mail: elvira.gaytan@inin.gob.mx [Comision Federal de Electricidad, Gerencia de Centrales Nucleoelectricas, Alto Lucero, Veracruz (Mexico)

2014-10-15

In this work is presented a Verification Methodology and Software Validation, to be applied in instruments of nuclear use with associate software. This methodology was developed under the auspices of IAEA, through the regional projects RLA4022 (ARCAL XCIX) and RLA1011 (RLA CXXIII), led by Mexico. In the first project three plans and three procedures were elaborated taking into consideration IEEE standards, and in the second project these documents were updated considering ISO and IEC standards. The developed methodology has been distributed to the participant countries of Latin America in the ARCAL projects and two related courses have been imparted with the participation of several countries, and participating institutions of Mexico like Instituto Nacional de Investigaciones Nucleares (ININ), Comision Federal de Electricidad (CFE) and Comision Nacional de Seguridad Nuclear y Salvaguardias (CNSNS). In the ININ due to the necessity to work with Software Quality Guarantee in systems for the nuclear power plant of the CFE, a Software Quality Guarantee Plan and five procedures were developed in the year 2004, obtaining the qualification of the ININ for software development for the nuclear power plant of CFE. These first documents were developed taking like reference IEEE standards and regulator guides of NRC, being the first step for the development of the methodology. (Author)

Software design for the EBT-P data acquisition and control system R and D

International Nuclear Information System (INIS)

Boyd, R.A.

1983-01-01

The instrumentation and control system for the EBT-P device is composed of a hierarchy of programmable logic controllers, microprocessor-based data acquisition computers, and a large minicomputer-based facility computer system. The software being developed to support this data acquisition and control system is necessarily quite complex due to several requirements imposed upon the EBT-P overall design criteria. These requirements, which include such considerations as overall reliability, operator interface, real-time display, interprocessor communication, and minimum cost to build, operate, and maintain, dictate that the software be developed in a well structured and controlled manner. To this end, structured software engineering practices are being applied to the design and development of the EBT-P data acquistion and control software. The design process began with the production of a software Requirements Document which describes the hardware and software environment in which the software development takes place. It identifies the major deliverable software items to be produced and describes the practices to be used to design and develop the software. The software design is split into three components: the facility computer software, the microcomputer software, and the PLC software. Within these physical boundaries, the following five functions are defined: data acquisition, display, communication, storage, and control. The software design is further detailed in a Structured Specification Document for each of the three physical components. Each specification describes the software in detailed terms so that a programmer can directly write the required software. Each specification is composed of: data flow diagrams, a data dictionary, structure diagrams, and program design language mini-specifications. Examples of the design issues exposed and addressed during the structured decomposition of EBT-P software processes are discussed in detail

Operation Request Gatekeeper: A software system for remote access control of diagnostic instruments in fusion experiments

International Nuclear Information System (INIS)

Abla, G.; Schissel, D. P.; Fredian, T. W.; Stillerman, J. A.; Greenwald, M. J.; Stepanov, D. N.; Ciarlette, D. J.

2010-01-01

Tokamak diagnostic settings are repeatedly modified to meet the changing needs of each experiment. Enabling the remote diagnostic control has significant challenges due to security and efficiency requirements. The Operation Request Gatekeeper (ORG) is a software system that addresses the challenges of remotely but securely submitting modification requests. The ORG provides a framework for screening all the requests before they enter the secure machine zone and are executed by performing user authentication and authorization, grammar validation, and validity checks. A prototype ORG was developed for the ITER CODAC that satisfies their initial requirements for remote request submission and has been tested with remote control of the KSTAR Plasma Control System. This paper describes the software design principles and implementation of ORG as well as worldwide test results.

The ITER Fast Plant System Controller ATCA prototype Real-Time Software Architecture

International Nuclear Information System (INIS)

Carvalho, B.B.; Santos, B.; Carvalho, P.F.; Neto, A.; Boncagni, L.; Batista, A.J.N.; Correia, M.; Sousa, J.; Gonçalves, B.

2013-01-01

Highlights: ► High performance ATCA systems for fast control and data acquisition. ► IEEE1588 timing system and synchronization. ► Plasma control algorithms. ► Real-time control software frameworks. ► Targeted for nuclear fusion experiments with long duration discharges. -- Abstract: IPFN is developing a prototype Fast Plant System Controller (FPSC) based in ATCA embedded technologies dedicated to ITER CODAC data acquisition and control tasks in the sub-millisecond range. The main goal is to demonstrate the usability of the ATCA standard and its enhanced specifications for the high speed, very high density parallel data acquisition needs of the most demanding ITER tokamak plasma Instrumentation and Control (I and C) systems. This effort included the in-house development of a new family of high performance ATCA I/O and timing boards. The standard ITER software system CODAC Core System (CCS) v3.1, with the control based in the EPICS system does not cover yet the real-time requirements fulfilled by this hardware, so a new set of software components was developed for this specific platform, attempting to integrate and leverage the new features in CSS, for example the Multithreaded Application Real Time executor (MARTe) software framework, the new Data Archiving Network (DAN) solution, an ATCA IEEE-1588-2008 timing interface, and the Intelligent Platform Management Interface (IPMI) for system monitoring and remote management. This paper presents the overall software architecture for the ATCA FPSC, as well a discussion on the ITER constrains and design choices and finally a detailed description of the software components already developed

The ITER Fast Plant System Controller ATCA prototype Real-Time Software Architecture

Energy Technology Data Exchange (ETDEWEB)

Carvalho, B.B., E-mail: bernardo@ipfn.ist.utl.pt [Associacao EURATOM/IST Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, P-1049-001 Lisboa (Portugal); Santos, B.; Carvalho, P.F.; Neto, A. [Associacao EURATOM/IST Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, P-1049-001 Lisboa (Portugal); Boncagni, L. [Associazione Euratom-ENEA sulla Fusione, Frascati Research Centre, Division of Fusion Physics, Frascati, Rome (Italy); Batista, A.J.N.; Correia, M.; Sousa, J.; Gonçalves, B. [Associacao EURATOM/IST Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, P-1049-001 Lisboa (Portugal)

2013-10-15

Highlights: ► High performance ATCA systems for fast control and data acquisition. ► IEEE1588 timing system and synchronization. ► Plasma control algorithms. ► Real-time control software frameworks. ► Targeted for nuclear fusion experiments with long duration discharges. -- Abstract: IPFN is developing a prototype Fast Plant System Controller (FPSC) based in ATCA embedded technologies dedicated to ITER CODAC data acquisition and control tasks in the sub-millisecond range. The main goal is to demonstrate the usability of the ATCA standard and its enhanced specifications for the high speed, very high density parallel data acquisition needs of the most demanding ITER tokamak plasma Instrumentation and Control (I and C) systems. This effort included the in-house development of a new family of high performance ATCA I/O and timing boards. The standard ITER software system CODAC Core System (CCS) v3.1, with the control based in the EPICS system does not cover yet the real-time requirements fulfilled by this hardware, so a new set of software components was developed for this specific platform, attempting to integrate and leverage the new features in CSS, for example the Multithreaded Application Real Time executor (MARTe) software framework, the new Data Archiving Network (DAN) solution, an ATCA IEEE-1588-2008 timing interface, and the Intelligent Platform Management Interface (IPMI) for system monitoring and remote management. This paper presents the overall software architecture for the ATCA FPSC, as well a discussion on the ITER constrains and design choices and finally a detailed description of the software components already developed.

Software-Based Wireless Power Transfer Platform for Various Power Control Experiments

Directory of Open Access Journals (Sweden)

Sun-Han Hwang

2015-07-01

Full Text Available In this paper, we present the design and evaluation of a software-based wireless power transfer platform that enables the development of a prototype involving various open- and closed-loop power control functions. Our platform is based on a loosely coupled planar wireless power transfer circuit that uses a class-E power amplifier. In conjunction with this circuit, we implement flexible control functions using a National Instruments Data Acquisition (NI DAQ board and algorithms in the MATLAB/Simulink. To verify the effectiveness of our platform, we conduct two types of power-control experiments: a no-load or metal detection using open-loop power control, and an output voltage regulation for different receiver positions using closed-loop power control. The use of the MATLAB/Simulink software as a part of the planar wireless power transfer platform for power control experiments is shown to serve as a useful and inexpensive alternative to conventional hardware-based platforms.

Software quality assurance plan for viscometer

International Nuclear Information System (INIS)

Gimera, M.

1994-01-01

The in situ viscometer is a portable instrument designed to raise and lower a sphere (rheometer ball) through layers of tank waste material while recording ball position, velocity, and cable tension. In the field, the viscometer attaches to a decontamination spool piece which in turn is designed to attach to any 4-inch, 150-pound flange (typical of many available tank risers). The motion of the ball and collection of data is controlled by instrumentation and control equipment housed in a separate remote control console. This document covers the product, Viscometer Data Acquisition Software. This document provides the software quality assurance plan, verification and validation plan, and configuration management plan for developing the software for the instrumentation that will be used to obtain rheology data from Tank SY-101

Hardware design for new instrumentation and control system of RTP

International Nuclear Information System (INIS)

Mohd Idris Taib; Izhar Abu Hussin; Zareen Khan Abdul Jalil Khan; Mohd Dzul Aiman Aslan; Mohd Khairulezwan Abdul Manan; Nurfarhana Ayuni Joha; Mohd Sabri Minhat

2010-01-01

The design for New Instrumentation and Control system of RTP are proposed. Physical system is modular-based, comprise of several cabinets such as Reactor Protection System 1 and 2, Control Console, Information Console 1 and 2 as well as Communication Console. Reactor Protection System automatically will shut-down reactor whenever safety limit setting was approach. Control console is where the reactor operator actually controls the reactor with control the movement of control rods. Information Consoles using Liquid Crystal Display to monitor the reactor parameters. Communication Console is where the communication tools such as telephone and intercom are located. This new system will incorporated analog, digital and computer-based. Reactor Protection System will use all analog system. Reactor Control System and Reactor Monitoring System will use analog as well as computer-based system. Wide-range channel will use digital signal processor as a main component. Controlling control rod movement is using control rod button via microprocessor-based control rod controller. Automatic Flux Controller is using embedded computer for flexibility of programming. Data Acquisition System is using Programmable Logic Controller and Industrial Computer. The main software for this system will be developed using WinCC software. (author)

A survey on the VXIbus and validity analyses for instrumentation and control in NPPs

International Nuclear Information System (INIS)

Kwon, Kee Choon; Park, Won Man

1997-06-01

This document presents the technical status of the VXIbus system and its interface. VMEbus, while developed as a backplane for Motorola processors, can be used for data acquisition, control and other instrumentation applications. The VXIbus and its associated standard for form, fit, and electrical interface have simplified the process of putting together automated instrumentation systems. The VXIplug and play system alliance was founded in 1993, the alliance's charter to improve the effectiveness of VXI-based solutions by increasing ease-of-use and improving the interoperability of mainframes, computers, instrumentations, and software through open, multivendor standards and practices. This technical report surveys surveys the instrumentation and control in NPPs apply to the VXI-based instruments which are studied expendability, interoperability, maintainability and other features. (author). 10 refs., 4 tabs., 25 figs

Modularity analysis of automotive control software

OpenAIRE

Dajsuren, Y.; Brand, van den, M.G.J.; Serebrenik, A.

2013-01-01

A design language and tool like MATLAB/Simulink is used for the graphical modelling and simulation of automotive control software. As the functionality based on electronics and software systems increases in motor vehicles, it is becoming increasingly important for system/software architects and control engineers in the automotive industry to ensure the quality of the highly complex MATLAB/Simulink control software. For automotive software, modularity is recognized as being a crucial quality a...

TELICS—A Telescope Instrument Control System for Small/Medium Sized Astronomical Observatories

Science.gov (United States)

Srivastava, Mudit K.; Ramaprakash, A. N.; Burse, Mahesh P.; Chordia, Pravin A.; Chillal, Kalpesh S.; Mestry, Vilas B.; Das, Hillol K.; Kohok, Abhay A.

2009-10-01

For any modern astronomical observatory, it is essential to have an efficient interface between the telescope and its back-end instruments. However, for small and medium-sized observatories, this requirement is often limited by tight financial constraints. Therefore a simple yet versatile and low-cost control system is required for such observatories to minimize cost and effort. Here we report the development of a modern, multipurpose instrument control system TELICS (Telescope Instrument Control System) to integrate the controls of various instruments and devices mounted on the telescope. TELICS consists of an embedded hardware unit known as a common control unit (CCU) in combination with Linux-based data acquisition and user interface. The hardware of the CCU is built around the ATmega 128 microcontroller (Atmel Corp.) and is designed with a backplane, master-slave architecture. A Qt-based graphical user interface (GUI) has been developed and the back-end application software is based on C/C++. TELICS provides feedback mechanisms that give the operator good visibility and a quick-look display of the status and modes of instruments as well as data. TELICS has been used for regular science observations since 2008 March on the 2 m, f/10 IUCAA Telescope located at Girawali in Pune, India.

Instrument Remote Control via the Astronomical Instrument Markup Language

Science.gov (United States)

Sall, Ken; Ames, Troy; Warsaw, Craig; Koons, Lisa; Shafer, Richard

1998-01-01

The Instrument Remote Control (IRC) project ongoing at NASA's Goddard Space Flight Center's (GSFC) Information Systems Center (ISC) supports NASA's mission by defining an adaptive intranet-based framework that provides robust interactive and distributed control and monitoring of remote instruments. An astronomical IRC architecture that combines the platform-independent processing capabilities of Java with the power of Extensible Markup Language (XML) to express hierarchical data in an equally platform-independent, as well as human readable manner, has been developed. This architecture is implemented using a variety of XML support tools and Application Programming Interfaces (API) written in Java. IRC will enable trusted astronomers from around the world to easily access infrared instruments (e.g., telescopes, cameras, and spectrometers) located in remote, inhospitable environments, such as the South Pole, a high Chilean mountaintop, or an airborne observatory aboard a Boeing 747. Using IRC's frameworks, an astronomer or other scientist can easily define the type of onboard instrument, control the instrument remotely, and return monitoring data all through the intranet. The Astronomical Instrument Markup Language (AIML) is the first implementation of the more general Instrument Markup Language (IML). The key aspects of our approach to instrument description and control applies to many domains, from medical instruments to machine assembly lines. The concepts behind AIML apply equally well to the description and control of instruments in general. IRC enables us to apply our techniques to several instruments, preferably from different observatories.

Experimental research control software system

International Nuclear Information System (INIS)

Cohn, I A; Kovalenko, A G; Vystavkin, A N

2014-01-01

A software system, intended for automation of a small scale research, has been developed. The software allows one to control equipment, acquire and process data by means of simple scripts. The main purpose of that development is to increase experiment automation easiness, thus significantly reducing experimental setup automation efforts. In particular, minimal programming skills are required and supervisors have no reviewing troubles. Interactions between scripts and equipment are managed automatically, thus allowing to run multiple scripts simultaneously. Unlike well-known data acquisition commercial software systems, the control is performed by an imperative scripting language. This approach eases complex control and data acquisition algorithms implementation. A modular interface library performs interaction with external interfaces. While most widely used interfaces are already implemented, a simple framework is developed for fast implementations of new software and hardware interfaces. While the software is in continuous development with new features being implemented, it is already used in our laboratory for automation of a helium-3 cryostat control and data acquisition. The software is open source and distributed under Gnu Public License.

Experimental research control software system

Science.gov (United States)

Cohn, I. A.; Kovalenko, A. G.; Vystavkin, A. N.

2014-05-01

A software system, intended for automation of a small scale research, has been developed. The software allows one to control equipment, acquire and process data by means of simple scripts. The main purpose of that development is to increase experiment automation easiness, thus significantly reducing experimental setup automation efforts. In particular, minimal programming skills are required and supervisors have no reviewing troubles. Interactions between scripts and equipment are managed automatically, thus allowing to run multiple scripts simultaneously. Unlike well-known data acquisition commercial software systems, the control is performed by an imperative scripting language. This approach eases complex control and data acquisition algorithms implementation. A modular interface library performs interaction with external interfaces. While most widely used interfaces are already implemented, a simple framework is developed for fast implementations of new software and hardware interfaces. While the software is in continuous development with new features being implemented, it is already used in our laboratory for automation of a helium-3 cryostat control and data acquisition. The software is open source and distributed under Gnu Public License.

A new instrument for statistical process control of thermoset molding

International Nuclear Information System (INIS)

Day, D.R.; Lee, H.L.; Shepard, D.D.; Sheppard, N.F.

1991-01-01

The recent development of a rugged ceramic mold mounted dielectric sensor and high speed dielectric instrumentation now enables monitoring and statistical process control of production molding over thousands of runs. In this work special instrumentation and software (ICAM-1000) was utilized that automatically extracts critical point during the molding process including flow point, viscosity minimum gel inflection, and reaction endpoint. In addition, other sensors were incorporated to measure temperature and pressure. The critical point as well as temperature and pressure were then recorded during normal production and then plotted in the form of statistical process control (SPC) charts. Experiments have been carried out in RIM, SMC, and RTM type molding operations. The influence of temperature, pressure chemistry, and other variables has been investigated. In this paper examples of both RIM and SMC are discussed

Intercomparison of alpha particle spectrometry software packages

International Nuclear Information System (INIS)

1999-08-01

Software has reached an important level as the 'logical controller' at different levels, from a single instrument to an entire computer-controlled experiment. This is also the case for software packages in nuclear instruments and experiments. In particular, because of the range of applications of alpha-particle spectrometry, software packages in this field are often used. It is the aim of this intercomparison to test and describe the abilities of four such software packages. The main objectives of the intercomparison were the ability of the programs to determine the peak areas and the peak area uncertainties, and the statistical control and stability of reported results. In this report, the task, methods and results of the intercomparison are presented in order to asist the potential users of such software and to stimulate the development of even better alpha-particle spectrum analysis software

SeDA: A software package for the statistical analysis of the instrument drift

International Nuclear Information System (INIS)

Lee, H. J.; Jang, S. C.; Lim, T. J.

2006-01-01

The setpoints for safety-related equipment are affected by many sources of an uncertainty. ANSI/ISA-S67.04.01-2000 [1] and ISA-RP6 7.04.02-2000 [2] suggested the statistical approaches for ensuring that the safety-related instrument setpoints were established and maintained within the technical specification limits [3]. However, Jang et al. [4] indicated that the preceding methodologies for a setpoint drift analysis might be insufficient to manage a setpoint drift on an instrumentation device and proposed new statistical analysis procedures for the management of a setpoint drift, based on the plant specific as-found/as-left data. Although IHPA (Instrument History Performance Analysis) is a widely known commercial software package to analyze an instrument setpoint drift, several steps in the new procedure cannot be performed by using it because it is based on the statistical approaches suggested in the ANSI/ISA-S67.04.01 -2000 [1] and ISA-RP67.04.02-2000 [2], In this paper we present a software package (SeDA: Setpoint Drift Analysis) that implements new methodologies, and which is easy to use, as it is accompanied by powerful graphical tools. (authors)

Verification and validation of software related to nuclear power plant control and instrumentation

International Nuclear Information System (INIS)

Wall, N.; Kossilov, A.

1994-01-01

There has always been significant concern with introduction of software in industry and the nuclear industry is no different from any other sector save its safety demands are some of the most onerous. The problems associated with software have led to the well documented difficulties in the introduction of computer based systems. An important area of concern with software in systems is the processes of Verification and Validation. One of the many activities the IAEA is currently engaged in is the preparation of a document on the process of verification and validation of software. The document follows the safety classification of IEC 1226 but includes software important to plant operation to establish three levels of assurance. The software that might be deployed on a plant was then identified as one of four types: new software, existing software for which full access to the code and documentation is possible, existing software of a proprietary nature and finally configurable software. The document attempts to identify the appropriate methods and tools for conducting the verification and validation processes. (author). 5 refs, 5 figs, 7 tabs

Techniques, processes, and measures for software safety and reliability

International Nuclear Information System (INIS)

Sparkman, D.

1992-01-01

The purpose of this report is to provide a detailed survey of current recommended practices and measurement techniques for the development of reliable and safe software-based systems. This report is intended to assist the United States Nuclear Reaction Regulation (NRR) in determining the importance and maturity of the available techniques and in assessing the relevance of individual standards for application to instrumentation and control systems in nuclear power generating stations. Lawrence Livermore National Laboratory (LLNL) provides technical support for the Instrumentation and Control System Branch (ICSB) of NRRin advanced instrumentation and control systems, distributed digital systems, software reliability, and the application of verificafion and validafion for the development of software

Construction of control and instrumentation devices of high voltage power supply of double chamber plasma nitrogen

International Nuclear Information System (INIS)

Saminto; Eko Priyono; Sugeng Riyanto

2013-01-01

A control and instrumentation devices of high voltage power supply of double chamber plasma nitrogen have been made. This device consists of the software and hardware component. Hardware component consists of SCR phase angle controller LPC-50HDA type, T100MD1616+ PLC, high voltage transformer and voltage rectifier system. Software component used a LADDER program and TBasic serves to control of the high voltage output. The components in these devices have been tested in the double chamber plasma nitrogen. Its performance meet with the design criteria that can supply of plasma nitrogen operation voltage in the range 290 Vdc to 851 Vdc with glow discharge current 0.4 A to 1.4 A. In general it can be said that the control and instrumentation devices of high voltage power supply is ready for use at the double chamber plasma nitrogen device. (author)

Solutions for cost effective assessment of software based instrumentation and control systems in nuclear power plants. Report prepared within the framework of the Technical Working Group on Nuclear Power Plant Control and Implementation

International Nuclear Information System (INIS)

2002-12-01

The introduction of software based instrumentation and control (I and C) systems for use in nuclear power plants, mainly due to I and C modernization activities, has raised many issues of safety and economics. Many of these issues have been raised in the IAEA Technical Working Group on Nuclear Power Plant Control and Instrumentation (TWG-NPPCI) meetings and by other organizations, such as the OECD and the European Commission. One increasingly important issue is the need for engineering solutions to justify them for the cost effective assessment and deployment of software based I and C systems. To address this important issue, the IAEA put together the Co-ordinated Research Project (CRP) on Solutions for Cost Effective Assessments of Software based I and C Systems. The overall objective of the project is to facilitate the cost effective assessment of software based I and C systems in nuclear power plants. This is necessary to address obsolescence issues, to introduce new beneficial functionality, and to improve overall performance. The engineering solutions developed in this CRP will contribute to this overall objective. The objective of the CRP was reached through co-ordinated research and collected experience in the areas of project management; requirements specifications; use of software explicitly designed for nuclear applications, use of commercial off the shelf (COTS) products, generic pre-qualification of systems and components; safety and reliability enhancements; verification and validation; and licensing impact. This TECDOC is the result of the research and collected experience put together under this CRP. The CRP participants gave presentations on their work performed as part of this CRP at the various meetings of the group. The first meeting of the CRP was held in Vienna on 8-12 November 1999 in which the participants developed the objectives, scope, and outline of this report. The second meeting was held in Halden, Norway on 4-8 December 2000 and the

An automated instrument for controlled-potential coulometry: System documentation

Energy Technology Data Exchange (ETDEWEB)

Holland, M K; Cordaro, J V

1988-06-01

An automated controlled-potential coulometer has been developed at the Savannah River Plant for the determination of plutonium. Two such coulometers have been assembled, evaluated, and applied. The software is based upon the methodology used at the Savannah River Plant, however the system is applicable with minimal software modifications to any of the methodologies used throughout the nuclear industry. These state-of-the-art coulometers feature electrical calibration of the integration system, background current corrections, and control-potential adjustment capabilities. Measurement precision within 0.1% has been demonstrated. The systems have also been successfully applied to the determination of pure neptunium solutions. The design and documentation of the automated instrument are described herein. Each individual module's operation, wiring layout, and alignment are described. Interconnection of the modules and system calibration are discussed. A complete set of system prints and a list of associated parts are included. 9 refs., 10 figs., 6 tabs.

The instrumental genesis process in future primary teachers using Dynamic Geometry Software

Science.gov (United States)

Ruiz-López, Natalia

2018-05-01

This paper, which describes a study undertaken with pairs of future primary teachers using GeoGebra software to solve geometry problems, includes a brief literature review, the theoretical framework and methodology used. An analysis of the instrumental genesis process for a pair participating in the case study is also provided. This analysis addresses the techniques and types of dragging used, the obstacles to learning encountered, a description of the interaction between the pair and their interaction with the teacher, and the type of language used. Based on this analysis, possibilities and limitations of the instrumental genesis process are identified for the development of geometric competencies such as conjecture creation, property checking and problem researching. It is also suggested that the methodology used in the analysis of the problem solving process may be useful for those teachers and researchers who want to integrate Dynamic Geometry Software (DGS) in their classrooms.

A new software for dimensional measurements in 3D endodontic root canal instrumentation

Directory of Open Access Journals (Sweden)

Raffaele Sinibaldi

2012-01-01

Full Text Available The main issue to be faced to get size estimates of 3D modification of the dental canal after endodontic treatment is the co-registration of the image stacks obtained through micro computed tomography (micro-CT scans before and after treatment. Here quantitative analysis of micro-CT images have been performed by means of new dedicated software targeted to the analysis of root canal after endodontic instrumentation. This software analytically calculates the best superposition between the pre and post structures using the inertia tensor of the tooth. This strategy avoid minimization procedures, which can be user dependent, and time consuming. Once the co-registration have been achieved dimensional measurements have then been performed by contemporary evaluation of quantitative parameters over the two superimposed stacks of micro-CT images. The software automatically calculated the changes of volume, surface and symmetry axes in 3D occurring after the instrumentation. The calculation is based on direct comparison of the canal and canal branches selected by the user on the pre treatment image stack.

Instrumentation and control systems for monitoring and data acquisition for thermal recovery process

Energy Technology Data Exchange (ETDEWEB)

Aparicio, J.; Hernandez, E.; Perozo, H. [PDVSA Intevep, S.A. (Venezuela)

2011-07-01

Thermal recovery methods are often applied to enhance oil recovery in heavy oil reservoirs, one of its challenges is to control the displacement of the thermal front. Methods are thus implemented to obtain data on the temperatures in the wells at any given time and to monitor other variables so that the behaviour of the thermal front can be predicted. The aim of this paper is to present a new control and instrumentation scheme to measure all of the variables. A software was created using Labview a graphs-based programming language software and PostgreSQL, a database management system. Using this software, sensors can be added or removed at any time; trends can be immediately visualized; and quality of the information is ensured since there is no human intervention in the data collection or processing. This paper presented a software which improves monitoring of all of the variables affecting the behaviour of the thermal front.

Space Telescope Pointing Control System software

Science.gov (United States)

Dougherty, H.; Rodoni, C.; Rossini, R.; Tompetrini, K.; Nakashima, A.; Bradley, A.

1982-01-01

The Space Telescope Pointing Control System software is in the advanced development stage, having been tested on both the airbearing and the static simulator. The overall structure of the software is discussed, along with timing and sizing evaluations. The interaction between the controls analysts and software designer is described.

Reactor instrumentation and control

International Nuclear Information System (INIS)

Wach, D.; Beraha, D.

1980-01-01

The methods for measuring radiation are shortly reviewed. The instrumentation for neutron flux measurement is classified into out-of-core and in-core instrumentation. The out-of-core instrumentation monitors the operational range from the subcritical reactor to full power. This large range is covered by several measurement channels which derive their signals from counter tubes and ionization chambers. The in-core instrumentation provides more detailed information on the power distribution in the core. The self-powered neutron detectors and the aeroball system in PWR reactors are discussed. Temperature and pressure measurement devices are briefly discussed. The different methods for leak detection are described. In concluding the plant instrumentation part some new monitoring systems and analysis methods are presented: early failure detection methods by noise analysis, acoustic monitoring and vibration monitoring. The presentation of the control starts from an qualitative assessment of the reactor dynamics. The chosen control strategy leads to the definition of the part-load diagram, which provides the set-points for the different control systems. The tasks and the functions of these control systems are described. In additiion to the control, a number of limiting systems is employed to keep the reactor in a safe operating region. Finally, an outlook is given on future developments in control, concerning mainly the increased application of process computers. (orig./RW)

Object oriented reconstruction software for the Instrumented Flux Return of BABAR

CERN Document Server

Nardo, E D; Lista, L

2001-01-01

BABAR experiment is the first High Energy Physics experiment to extensively use object oriented technology and the C++ programming language for online and offline software. Object orientation permits to reach a high level of flexibility and maintainability of the code, which is a key point in a large project with many developers. These goals are reached with the introduction of reusable code elements, with abstraction of code behaviours and polymorphism. Software design, before code implementation, is the key task that determines the achievement of such a goal. We present the experience with the application of object oriented technology and design patterns to the reconstruction software of the Instrumented Flux Return detector of BABAR experiment. The use of abstract interfaces improved the development of reconstruction code and permitted to flexibly apply modification to reconstruction strategies, and eventually to reduce the maintenance load. The experience during the last years of development is presented....

Instrumentation, control and modellisation/simulation in waste water treatment plants; Instrumentacion, control y modelizacion/simulacion en plantas depuradoras de aguas residuales

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, E.; Martinez, J. L.; Llorente, V.

2002-07-01

Controlling waste water treatment plants presents numerous problems as a result of the complexity of the task involved in managing them. The different instruments used in monitoring and controlling the flow, dissolved oxygen, pH, cloudiness and other parameters involved in the treatment process at level 0 are listed and described. The control and regulation equipment comprising level 1 is operated by the process computers of level 2. The different types of instruments are studied in relation to monitoring and control and the analysis and management o the data supplied by the instrumentation, the control strategies, operational margins and applicable software. Several case studies of activated sludge treatment processes are included to facilitate comprehension. Finally, the simulation models are presented with a view to aiding understanding, management and prediction of the operation of waste water treatment plants, particularly in regard to the problems of bulking and/or foaming. (Author)

The U.S./IAEA Workshop on Software Sustainability for Safeguards Instrumentation: Report to the NNSA DOE Office of International Nuclear Safeguards (NA-241)

Energy Technology Data Exchange (ETDEWEB)

Pepper, Susan E. [Brookhaven National Lab. (BNL), Upton, NY (United States); Pickett, Chris A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Queirolo, Al [Brookhaven National Lab. (BNL), Upton, NY (United States); Bachner, Katherine M. [Brookhaven National Lab. (BNL), Upton, NY (United States); Worrall, Louise G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-04-07

The U.S Department of Energy (DOE) National Nuclear Security Administration (NNSA) Next Generation Safeguards Initiative (NGSI) and the International Atomic Energy Agency (IAEA) convened a workshop on Software Sustainability for Safeguards Instrumentation in Vienna, Austria, May 6-8, 2014. Safeguards instrumentation software must be sustained in a changing environment to ensure existing instruments can continue to perform as designed, with improved security. The approaches to the development and maintenance of instrument software used in the past may not be the best model for the future and, therefore, the organizers’ goal was to investigate these past approaches and to determine an optimal path forward. The purpose of this report is to provide input for the DOE NNSA Office of International Nuclear Safeguards (NA-241) and other stakeholders that can be utilized when making decisions related to the development and maintenance of software used in the implementation of international nuclear safeguards. For example, this guidance can be used when determining whether to fund the development, upgrade, or replacement of a particular software product. The report identifies the challenges related to sustaining software, and makes recommendations for addressing these challenges, supported by summaries and detailed notes from the workshop discussions. In addition the authors provide a set of recommendations for institutionalizing software sustainability practices in the safeguards community. The term “software sustainability” was defined for this workshop as ensuring that safeguards instrument software and algorithm functionality can be maintained efficiently throughout the instrument lifecycle, without interruption and providing the ability to continue to improve that software as needs arise.

The U.S./IAEA Workshop on Software Sustainability for Safeguards Instrumentation: Report to the NNSA DOE Office of International Nuclear Safeguards (NA-241)

International Nuclear Information System (INIS)

Pepper, Susan E.; Pickett, Chris A.; Queirolo, Al; Bachner, Katherine M.; Worrall, Louise G.

2015-01-01

The U.S Department of Energy (DOE) National Nuclear Security Administration (NNSA) Next Generation Safeguards Initiative (NGSI) and the International Atomic Energy Agency (IAEA) convened a workshop on Software Sustainability for Safeguards Instrumentation in Vienna, Austria, May 6-8, 2014. Safeguards instrumentation software must be sustained in a changing environment to ensure existing instruments can continue to perform as designed, with improved security. The approaches to the development and maintenance of instrument software used in the past may not be the best model for the future and, therefore, the organizers' goal was to investigate these past approaches and to determine an optimal path forward. The purpose of this report is to provide input for the DOE NNSA Office of International Nuclear Safeguards (NA-241) and other stakeholders that can be utilized when making decisions related to the development and maintenance of software used in the implementation of international nuclear safeguards. For example, this guidance can be used when determining whether to fund the development, upgrade, or replacement of a particular software product. The report identifies the challenges related to sustaining software, and makes recommendations for addressing these challenges, supported by summaries and detailed notes from the workshop discussions. In addition the authors provide a set of recommendations for institutionalizing software sustainability practices in the safeguards community. The term ''software sustainability'' was defined for this workshop as ensuring that safeguards instrument software and algorithm functionality can be maintained efficiently throughout the instrument lifecycle, without interruption and providing the ability to continue to improve that software as needs arise.

Upgrading instrumentation and control in nuclear power plants. Design criteria

International Nuclear Information System (INIS)

Rodriguez Rodriguez, M.C.; Alvarez Menendez, A.

1997-01-01

The use of programmed digital technology in Protection, Control, Monitoring and Information Systems in new generation nuclear power plants, or the use of this technology to replace or upgrade existing systems based on wired analog instrumentation and electromechanical relays, has led to new international standards which establish new design requirements or adapt existing requirements to this technology. Additionally, both regulatory organisations and the industry are discussing the reliability of this technology, regarding common mode failures that may occur in redundant protection channels, due to the use of equipment and software with the same characteristics. The first part of this paper addresses the most important aspects of new international standards regarding classification criteria for I and C systems, equipment and functions, depending on their importance to safety and the design criteria applicable to each category. Special attention is drawn to requirements concerning software quality assurance and the design of new control rooms. The paper then goes on to discuss the different technical solutions being implemented, using equipment and software diversification, in order to prevent the possibility of common mode failures affecting the protection function. (Author)

Integrated management tool for controls software problems, requests and project tasking at SLAC

International Nuclear Information System (INIS)

Rogind, D.; Allen, W.; Colocho, W.; DeContreras, G.; Gordon, J.; Pandey, P.; Shoaee, H.

2012-01-01

The Accelerator Directorate (AD) Instrumentation and Controls (ICD) Software (SW) Department at SLAC, with its service center model, continuously receives engineering requests to design, build and support controls for accelerator systems lab-wide. Each customer request can vary in complexity from a small software engineering change to a major enhancement. SLAC's Accelerator Improvement Projects (AIPs), along with DOE Construction projects, also contribute heavily to the work load. The various customer requests and projects, paired with the ongoing operational maintenance and problem reports, place a demand on the department that consistently exceeds the capacity of available resources. A centralized repository - comprised of all requests, project tasks, and problems - available to physicists, operators, managers, and engineers alike, is essential to capture, communicate, prioritize, assign, schedule, track, and finally, commission all work components. The Software Department has recently integrated request / project tasking into SLAC's custom online problem tracking 'Comprehensive Accelerator Tool for Enhancing Reliability' (CATER) tool. This paper discusses the newly implemented software request management tool - the workload it helps to track, its structure, features, reports, work-flow and its many usages. (authors)

Automatic sample changer control software for automation of neutron activation analysis process in Malaysian Nuclear Agency

Science.gov (United States)

Yussup, N.; Ibrahim, M. M.; Rahman, N. A. A.; Mokhtar, M.; Salim, N. A. A.; Soh@Shaari, S. C.; Azman, A.; Lombigit, L.; Azman, A.; Omar, S. A.

2018-01-01

Most of the procedures in neutron activation analysis (NAA) process that has been established in Malaysian Nuclear Agency (Nuclear Malaysia) since 1980s were performed manually. These manual procedures carried out by the NAA laboratory personnel are time consuming and inefficient especially for sample counting and measurement process. The sample needs to be changed and the measurement software needs to be setup for every one hour counting time. Both of these procedures are performed manually for every sample. Hence, an automatic sample changer system (ASC) that consists of hardware and software is developed to automate sample counting process for up to 30 samples consecutively. This paper describes the ASC control software for NAA process which is designed and developed to control the ASC hardware and call GammaVision software for sample measurement. The software is developed by using National Instrument LabVIEW development package.

The Instrumental Genesis Process in Future Primary Teachers Using Dynamic Geometry Software

Science.gov (United States)

Ruiz-López, Natalia

2018-01-01

This paper, which describes a study undertaken with pairs of future primary teachers using GeoGebra software to solve geometry problems, includes a brief literature review, the theoretical framework and methodology used. An analysis of the instrumental genesis process for a pair participating in the case study is also provided. This analysis…

Speckle interferometry. Data acquisition and control for the SPID instrument.

Science.gov (United States)

Altarac, S.; Tallon, M.; Thiebaut, E.; Foy, R.

1998-08-01

SPID (SPeckle Imaging by Deconvolution) is a new speckle camera currently under construction at CRAL-Observatoire de Lyon. Its high spectral resolution and high image restoration capabilities open new astrophysical programs. The instrument SPID is composed of four main optical modules which are fully automated and computer controlled by a software written in Tcl/Tk/Tix and C. This software provides an intelligent assistance to the user by choosing observational parameters as a function of atmospheric parameters, computed in real time, and the desired restored image quality. Data acquisition is made by a photon-counting detector (CP40). A VME-based computer under OS9 controls the detector and stocks the data. The intelligent system runs under Linux on a PC. A slave PC under DOS commands the motors. These 3 computers communicate through an Ethernet network. SPID can be considered as a precursor for VLT's (Very Large Telescope, four 8-meter telescopes currently built in Chile by European Southern Observatory) very high spatial resolution camera.

Temperature control system for optical elements in astronomical instrumentation

Science.gov (United States)

Verducci, Orlando; de Oliveira, Antonio C.; Ribeiro, Flávio F.; Vital de Arruda, Márcio; Gneiding, Clemens D.; Fraga, Luciano

2014-07-01

Extremely low temperatures may damage the optical components assembled inside of an astronomical instrument due to the crack in the resin or glue used to attach lenses and mirrors. The environment, very cold and dry, in most of the astronomical observatories contributes to this problem. This paper describes the solution implemented at SOAR for remotely monitoring and controlling temperatures inside of a spectrograph, in order to prevent a possible damage of the optical parts. The system automatically switches on and off some heat dissipation elements, located near the optics, as the measured temperature reaches a trigger value. This value is set to a temperature at which the instrument is not operational to prevent malfunction and only to protect the optics. The software was developed with LabVIEWTM and based on an object-oriented design that offers flexibility and ease of maintenance. As result, the system is able to keep the internal temperature of the instrument above a chosen limit, except perhaps during the response time, due to inertia of the temperature. This inertia can be controlled and even avoided by choosing the correct amount of heat dissipation and location of the thermal elements. A log file records the measured temperature values by the system for operation analysis.

Software engineering practices for control system reliability

International Nuclear Information System (INIS)

S. K. Schaffner; K. S White

1999-01-01

This paper will discuss software engineering practices used to improve Control System reliability. The authors begin with a brief discussion of the Software Engineering Institute's Capability Maturity Model (CMM) which is a framework for evaluating and improving key practices used to enhance software development and maintenance capabilities. The software engineering processes developed and used by the Controls Group at the Thomas Jefferson National Accelerator Facility (Jefferson Lab), using the Experimental Physics and Industrial Control System (EPICS) for accelerator control, are described. Examples are given of how their procedures have been used to minimized control system downtime and improve reliability. While their examples are primarily drawn from their experience with EPICS, these practices are equally applicable to any control system. Specific issues addressed include resource allocation, developing reliable software lifecycle processes and risk management

The software developing method for multichannel computer-aided system for physical experiments control, realized by resources of national instruments LabVIEW instrumental package

International Nuclear Information System (INIS)

Gorskaya, E.A.; Samojlov, V.N.

1999-01-01

This work is describing the method of developing the computer-aided control system in integrated environment of LabVIEW. Using the object-oriented design of complex systems, the hypothetical model for methods of developing the software for computer-aided system for physical experiments control was constructed. Within the framework of that model architecture solutions and implementations of suggested method were described. (author)

Software ecosystems analyzing and managing business networks in the software industry

CERN Document Server

Jansen, S; Cusumano, MA

2013-01-01

This book describes the state-of-the-art of software ecosystems. It constitutes a fundamental step towards an empirically based, nuanced understanding of the implications for management, governance, and control of software ecosystems. This is the first book of its kind dedicated to this emerging field and offers guidelines on how to analyze software ecosystems; methods for managing and growing; methods on transitioning from a closed software organization to an open one; and instruments for dealing with open source, licensing issues, product management and app stores. It is unique in bringing t

Software for mass spectrometer control

International Nuclear Information System (INIS)

Curuia, Marian; Culcer, Mihai; Anghel, Mihai; Iliescu, Mariana; Trancota, Dan; Kaucsar, Martin; Oprea, Cristiana

2004-01-01

The paper describes a software application for the MAT 250 mass spectrometer control, which was refurbished. The spectrometer was bring-up-to-date using a hardware structure on its support where the software application for mass spectrometer control was developed . The software application is composed of dedicated modules that perform given operations. The instructions that these modules have to perform are generated by a principal module. This module makes possible the change of information between the modules that compose the software application. The use of a modal structure is useful for adding new functions in the future. The developed application in our institute made possible the transformation of the mass spectrometer MAT 250 into a device endowed with other new generation tools. (authors)

On Model Based Synthesis of Embedded Control Software

OpenAIRE

Alimguzhin, Vadim; Mari, Federico; Melatti, Igor; Salvo, Ivano; Tronci, Enrico

2012-01-01

Many Embedded Systems are indeed Software Based Control Systems (SBCSs), that is control systems whose controller consists of control software running on a microcontroller device. This motivates investigation on Formal Model Based Design approaches for control software. Given the formal model of a plant as a Discrete Time Linear Hybrid System and the implementation specifications (that is, number of bits in the Analog-to-Digital (AD) conversion) correct-by-construction control software can be...

Instrumentation, computer software and experimental techniques used in low-frequency internal friction studies at WNRE

International Nuclear Information System (INIS)

Sprugmann, K.W.; Ritchie, I.G.

1980-04-01

A detailed and comprehensive account of the equipment, computer programs and experimental methods developed at the Whiteshell Nuclear Research Estalbishment for the study of low-frequency internal friction is presented. Part 1 describes the mechanical apparatus, electronic instrumentation and computer software, while Part II describes in detail the laboratory techniques and various types of experiments performed together with data reduction and analysis. Experimental procedures for the study of internal friction as a function of temperature, strain amplitude or time are described. Computer control of these experiments using the free-decay technique is outlined. In addition, a pendulum constant-amplitude drive system is described. (auth)

Web based remote instrumentation and control

International Nuclear Information System (INIS)

Dhekne, P.S.; Patil, Jitendra; Kulkarni, Jitendra; Babu, Prasad; Lad, U.C.; Rahurkar, A.G.; Kaura, H.K.

2001-01-01

The Web-based technology provides a very powerful communication medium for transmitting effectively multimedia information containing data generated from various sources, which may be in the form of audio, video, text, still or moving images etc. Large number of sophisticated web based software tools are available that can be used to monitor and control distributed electronic instrumentation projects. For example data can be collected online from various smart sensors/instruments such as images from CCD camera, pressure/ humidity sensor, light intensity transducer, smoke detectors etc and uploaded in real time to a central web server. This information can be processed further, to take control action in real time from any remote client, of course with due security care. The web-based technology offers greater flexibility, higher functionality, and high degree of integration providing standardization. Further easy to use standard browser based interface at the client end to monitor, view and control the desired process parameters allow you to cut down the development time and cost to a great extent. A system based on a web client-server approach has been designed and developed at Computer division, BARC and is operational since last year to monitor and control remotely various environmental parameters of distributed computer centers. In this paper we shall discuss details of this system, its current status and additional features which are currently under development. This type of system is typically very useful for Meteorology, Environmental monitoring of Nuclear stations, Radio active labs, Nuclear waste immobilization plants, Medical and Biological research labs., Security surveillance and in many such distributed situations. A brief description of various tools used for this project such as Java, CGI, Java Script, HTML, VBScript, M-JPEG, TCP/IP, UDP, RTP etc. along with their merits/demerits have also been included

Effective handling of software anomalies in computer based systems at nuclear power plants. Report prepared within the framework of the International Working Group on Nuclear Power Plant Control and Instrumentation

International Nuclear Information System (INIS)

2000-03-01

This report reviews possible types of anomalies that are related to software in nuclear power plants, outlines techniques that can be used to identify anomalies throughout the entire software life-cycle, and discusses important issues that must be considered during anomaly investigation and resolution. Typically, anomalies are identified, investigated and resolved during the normal process of developing or maintaining plant software, where these activities are covered by procedures and tools that are part of this process. Nevertheless, to reduce the number and impact of anomalies under plant operating conditions, it is important to ensure that good plans, procedures and tools are in place throughout the software life-cycle. The need for this was pointed out by the IAEA International Working Group on Nuclear Power Plant Control and Instrumentation (IWG-NPPCI). The report is the result of a series of consultants meetings held by the IAEA in 1997 and 1998 in Vienna. It was prepared with the participation and contributions of experts from Austria, Canada, Germany, Hungary, the United Kingdom and the United States of America. The scope of activities described in this report covers a methodology for anomaly identification, anomaly investigation and anomaly resolution. The activities to be done within these steps strongly depend on the safety category of the software, the actual life-cycle phase of the software, the type of the software and the severity of the anomaly

Software product quality control

CERN Document Server

Wagner, Stefan

2013-01-01

Quality is not a fixed or universal property of software; it depends on the context and goals of its stakeholders. Hence, when you want to develop a high-quality software system, the first step must be a clear and precise specification of quality. Yet even if you get it right and complete, you can be sure that it will become invalid over time. So the only solution is continuous quality control: the steady and explicit evaluation of a product's properties with respect to its updated quality goals.This book guides you in setting up and running continuous quality control in your environment. Star

KAERI software safety guideline for developing safety-critical software in digital instrumentation and control system of nuclear power plant

International Nuclear Information System (INIS)

Lee, Jang Soo; Kim, Jang Yeol; Eum, Heung Seop.

1997-07-01

Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organization. The requirements for software important to safety of nuclear reactor are described in such positions and standards. Most of them are describing mandatory requirements, what shall be done, for the safety-critical software. The developers of such a software. However, there have been a lot of controversial factors on whether the work practices satisfy the regulatory requirements, and to justify the safety of such a system developed by the work practices, between the licenser and the licensee. We believe it is caused by the reason that there is a gap between the mandatory requirements (What) and the work practices (How). We have developed a guidance to fill such gap, which can be useful for both licenser and licensee to conduct a justification of the safety in the planning phase of developing the software for nuclear reactor protection systems. (author). 67 refs., 13 tabs., 2 figs

KAERI software safety guideline for developing safety-critical software in digital instrumentation and control system of nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Lee, Jang Soo; Kim, Jang Yeol; Eum, Heung Seop

1997-07-01

Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organization. The requirements for software important to safety of nuclear reactor are described in such positions and standards. Most of them are describing mandatory requirements, what shall be done, for the safety-critical software. The developers of such a software. However, there have been a lot of controversial factors on whether the work practices satisfy the regulatory requirements, and to justify the safety of such a system developed by the work practices, between the licenser and the licensee. We believe it is caused by the reason that there is a gap between the mandatory requirements (What) and the work practices (How). We have developed a guidance to fill such gap, which can be useful for both licenser and licensee to conduct a justification of the safety in the planning phase of developing the software for nuclear reactor protection systems. (author). 67 refs., 13 tabs., 2 figs.

Software qualification for digital safety system in KNICS project

International Nuclear Information System (INIS)

Kwon, Kee-Choon; Lee, Dong-Young; Choi, Jong-Gyun

2012-01-01

In order to achieve technical self-reliance in the area of nuclear instrumentation and control, the Korea Nuclear Instrumentation and Control System (KNICS) project had been running for seven years from 2001. The safety-grade Programmable Logic Controller (PLC) and the digital safety system were developed by KNICS project. All the software of the PLC and digital safety system were developed and verified following the software development life cycle Verification and Validation (V and V) procedure. The main activities of the V and V process are preparation of software planning documentations, verification of the Software Requirement Specification (SRS), Software Design Specification (SDS) and codes, and a testing of the software components, the integrated software, and the integrated system. In addition, a software safety analysis and a software configuration management are included in the activities. For the software safety analysis at the SRS and SDS phases, the software Hazard Operability (HAZOP) was performed and then the software fault tree analysis was applied. The software fault tree analysis was applied to a part of software module with some critical defects identified by the software HAZOP in SDS phase. The software configuration management was performed using the in-house tool developed in the KNICS project. (author)

Antenna Controller Replacement Software

Science.gov (United States)

Chao, Roger Y.; Morgan, Scott C.; Strain, Martha M.; Rockwell, Stephen T.; Shimizu, Kenneth J.; Tehrani, Barzia J.; Kwok, Jaclyn H.; Tuazon-Wong, Michelle; Valtier, Henry; Nalbandi, Reza;

Advanced communications technology satellite high burst rate link evaluation terminal power control and rain fade software test plan, version 1.0

Science.gov (United States)

Reinhart, Richard C.

1993-01-01

The Power Control and Rain Fade Software was developed at the NASA Lewis Research Center to support the Advanced Communications Technology Satellite High Burst Rate Link Evaluation Terminal (ACTS HBR-LET). The HBR-LET is an experimenters terminal to communicate with the ACTS for various experiments by government, university, and industry agencies. The Power Control and Rain Fade Software is one segment of the Control and Performance Monitor (C&PM) Software system of the HBR-LET. The Power Control and Rain Fade Software automatically controls the LET uplink power to compensate for signal fades. Besides power augmentation, the C&PM Software system is also responsible for instrument control during HBR-LET experiments, control of the Intermediate Frequency Switch Matrix on board the ACTS to yield a desired path through the spacecraft payload, and data display. The Power Control and Rain Fade Software User's Guide, Version 1.0 outlines the commands and procedures to install and operate the Power Control and Rain Fade Software. The Power Control and Rain Fade Software Maintenance Manual, Version 1.0 is a programmer's guide to the Power Control and Rain Fade Software. This manual details the current implementation of the software from a technical perspective. Included is an overview of the Power Control and Rain Fade Software, computer algorithms, format representations, and computer hardware configuration. The Power Control and Rain Fade Test Plan provides a step-by-step procedure to verify the operation of the software using a predetermined signal fade event. The Test Plan also provides a means to demonstrate the capability of the software.

Modularity analysis of automotive control software

NARCIS (Netherlands)

Dajsuren, Y.; Brand, van den M.G.J.; Serebrenik, A.

2013-01-01

A design language and tool like MATLAB/Simulink is used for the graphical modelling and simulation of automotive control software. As the functionality based on electronics and software systems increases in motor vehicles, it is becoming increasingly important for system/software architects and

Building of a CAD system for instrumentation and control system of nuclear power plant

International Nuclear Information System (INIS)

Ma Zhicai; Hu Chunping; Zhang Dongsheng

2012-01-01

Base on the analysis of deign documents and process, a database for instrumentation and control system design can be developed with a popular desktop relational database management system (RDBMS). With the RDBMS, an instrumentation and control system CAD system can be built unitizing database link feature of popular CAD software, with the function of management of design data, output of list and forms. and design of drawings. A CAD system of this kind has been used in the design practice of nuclear power plant. With this system, it is shown that, the consistency of information has been controlled and the load on the engineer has been significantly reduced. The methodology used here can also be used in the CAD system for CAP1000 and CAP1400 plant. (authors) series

Software-Enabled Modular Instrumentation Systems

NARCIS (Netherlands)

Soijer, M.W.

2003-01-01

Like most other types of instrumentation systems, flight test instrumentation is not produced in series; its development is a one-time achievement by a test department. With the introduction of powerful digital computers, instrumentation systems have included data analysis tasks that were previously

Instrumentino: An Open-Source Software for Scientific Instruments

OpenAIRE

Koenka, Israel Joel; Sáiz, Jorge; Hauser, Peter C.

2015-01-01

Scientists often need to build dedicated computer-controlled experimental systems. For this purpose, it is becoming common to employ open-source microcontroller platforms, such as the Arduino. These boards and associated integrated software development environments provide affordable yet powerful solutions for the implementation of hardware control of transducers and acquisition of signals from detectors and sensors. It is, however, a challenge to write programs that allow interactive use of ...

Software quality assurance and software safety in the Biomed Control System

International Nuclear Information System (INIS)

Singh, R.P.; Chu, W.T.; Ludewigt, B.A.; Marks, K.M.; Nyman, M.A.; Renner, T.R.; Stradtner, R.

1989-01-01

The Biomed Control System is a hardware/software system used for the delivery, measurement and monitoring of heavy-ion beams in the patient treatment and biology experiment rooms in the Bevalac at the Lawrence Berkeley Laboratory (LBL). This paper describes some aspects of this system including historical background philosophy, configuration management, hardware features that facilitate software testing, software testing procedures, the release of new software quality assurance, safety and operator monitoring. 3 refs

Incorporation of Markov reliability models for digital instrumentation and control systems into existing PRAs

International Nuclear Information System (INIS)

Bucci, P.; Mangan, L. A.; Kirschenbaum, J.; Mandelli, D.; Aldemir, T.; Arndt, S. A.

2006-01-01

Markov models have the ability to capture the statistical dependence between failure events that can arise in the presence of complex dynamic interactions between components of digital instrumentation and control systems. One obstacle to the use of such models in an existing probabilistic risk assessment (PRA) is that most of the currently available PRA software is based on the static event-tree/fault-tree methodology which often cannot represent such interactions. We present an approach to the integration of Markov reliability models into existing PRAs by describing the Markov model of a digital steam generator feedwater level control system, how dynamic event trees (DETs) can be generated from the model, and how the DETs can be incorporated into an existing PRA with the SAPHIRE software. (authors)

New GPIB Control Software at Jefferson Lab

International Nuclear Information System (INIS)

Matthew Bickley; Pavel Chevtsov

2005-01-01

The control of GPIB devices at Jefferson Lab is based on the GPIB device/driver library. The library is a part of the device/driver development framework. It is activated with the use of the device configuration files that define all hardware components used in the control system to communicate with GPIB devices. As soon as the software is activated, it is ready to handle any device connected to these components and only needs to know the set of commands that the device can understand. The old GPIB control software at Jefferson Lab requires the definition of these commands in the form of a device control software module written in C for each device. Though such modules are relatively simple, they have to be created, successfully compiled, and supported for all control computer platforms. In the new version of GPIB control software all device communication commands are defined in device protocol (ASCII text) files. This makes the support of GPIB devices in the control system much easier

Development, structure and qualification of a new digital instrumentation and control system

International Nuclear Information System (INIS)

Hofmann, H.; Sauer, H.J.

1991-01-01

Introduction of digital instrumentation and control in nuclear power plants is characterized by the need to meet numerous requirements concerning reliability, ergonomic design of the main control room and comprehensive qualification. The system described here is distinguished by a hierarchical and modular structure, being redundant throughout. Ergonomic considerations dominate the layout of the screen-based main control room. Powerful computer-aided engineering tools are employed for planning of the entire system and for generation of the user software. Qualification is performed in step with the development of the system, based on the applicable national and international rules and regulations and in close cooperation with an independent expert. (orig.) [de

Open core control software for surgical robots.

Science.gov (United States)

Arata, Jumpei; Kozuka, Hiroaki; Kim, Hyung Wook; Takesue, Naoyuki; Vladimirov, B; Sakaguchi, Masamichi; Tokuda, Junichi; Hata, Nobuhiko; Chinzei, Kiyoyuki; Fujimoto, Hideo

2010-05-01

In these days, patients and doctors in operation room are surrounded by many medical devices as resulting from recent advancement of medical technology. However, these cutting-edge medical devices are working independently and not collaborating with each other, even though the collaborations between these devices such as navigation systems and medical imaging devices are becoming very important for accomplishing complex surgical tasks (such as a tumor removal procedure while checking the tumor location in neurosurgery). On the other hand, several surgical robots have been commercialized, and are becoming common. However, these surgical robots are not open for collaborations with external medical devices in these days. A cutting-edge "intelligent surgical robot" will be possible in collaborating with surgical robots, various kinds of sensors, navigation system and so on. On the other hand, most of the academic software developments for surgical robots are "home-made" in their research institutions and not open to the public. Therefore, open source control software for surgical robots can be beneficial in this field. From these perspectives, we developed Open Core Control software for surgical robots to overcome these challenges. In general, control softwares have hardware dependencies based on actuators, sensors and various kinds of internal devices. Therefore, these control softwares cannot be used on different types of robots without modifications. However, the structure of the Open Core Control software can be reused for various types of robots by abstracting hardware dependent parts. In addition, network connectivity is crucial for collaboration between advanced medical devices. The OpenIGTLink is adopted in Interface class which plays a role to communicate with external medical devices. At the same time, it is essential to maintain the stable operation within the asynchronous data transactions through network. In the Open Core Control software, several

Advanced transport operating system software upgrade: Flight management/flight controls software description

Science.gov (United States)

Clinedinst, Winston C.; Debure, Kelly R.; Dickson, Richard W.; Heaphy, William J.; Parks, Mark A.; Slominski, Christopher J.; Wolverton, David A.

1988-01-01

The Flight Management/Flight Controls (FM/FC) software for the Norden 2 (PDP-11/70M) computer installed on the NASA 737 aircraft is described. The software computes the navigation position estimates, guidance commands, those commands to be issued to the control surfaces to direct the aircraft in flight based on the modes selected on the Advanced Guidance Control System (AGSC) mode panel, and the flight path selected via the Navigation Control/Display Unit (NCDU).

49 CFR 236.18 - Software management control plan.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Software management control plan. 236.18 Section... Instructions: All Systems General § 236.18 Software management control plan. (a) Within 6 months of June 6, 2005, each railroad shall develop and adopt a software management control plan for its signal and train...

The SOFIA Mission Control System Software

Science.gov (United States)

Heiligman, G. M.; Brock, D. R.; Culp, S. D.; Decker, P. H.; Estrada, J. C.; Graybeal, J. B.; Nichols, D. M.; Paluzzi, P. R.; Sharer, P. J.; Pampell, R. J.; Papke, B. L.; Salovich, R. D.; Schlappe, S. B.; Spriestersbach, K. K.; Webb, G. L.

1999-05-01

The Stratospheric Observatory for Infrared Astronomy (SOFIA) will be delivered with a computerized mission control system (MCS). The MCS communicates with the aircraft's flight management system and coordinates the operations of the telescope assembly, mission-specific subsystems, and the science instruments. The software for the MCS must be reliable and flexible. It must be easily usable by many teams of observers with widely differing needs, and it must support non-intrusive access for education and public outreach. The technology must be appropriate for SOFIA's 20-year lifetime. The MCS software development process is an object-oriented, use case driven approach. The process is iterative: delivery will be phased over four "builds"; each build will be the result of many iterations; and each iteration will include analysis, design, implementation, and test activities. The team is geographically distributed, coordinating its work via Web pages, teleconferences, T.120 remote collaboration, and CVS (for Internet-enabled configuration management). The MCS software architectural design is derived in part from other observatories' experience. Some important features of the MCS are: * distributed computing over several UNIX and VxWorks computers * fast throughput of time-critical data * use of third-party components, such as the Adaptive Communications Environment (ACE) and the Common Object Request Broker Architecture (CORBA) * extensive configurability via stored, editable configuration files * use of several computer languages so developers have "the right tool for the job". C++, Java, scripting languages, Interactive Data Language (from Research Systems, Int'l.), XML, and HTML will all be used in the final deliverables. This paper reports on work in progress, with the final product scheduled for delivery in 2001. This work was performed for Universities Space Research Association for NASA under contract NAS2-97001.

Tool – Material, Metaphor – Metonymy, Instrument(ness)

DEFF Research Database (Denmark)

Bertelsen, Olav Wedege; Breinbjerg, Morten; Pold, Søren

2008-01-01

creativity , supported by analysis of, and interviews with, musical composers. Instrumentness is explained through discussions of materiality and metonymy as central strategies for computer mediated creativity. The paper is contributing to an investigation of the aesthetics of use in relation to software...... are controlled and conceptualized through values such as virtuosity and palyability, which are important for computer-mediated creative work supporting development in use beyond what is initially designed for. The papet performs a conceptual investigation into qualities in software interfaces that support...

Notes on instrumentation and control

CERN Document Server

Roy, G J

2013-01-01

Notes on Instrumentation and Control presents topics on pressure (i.e., U-tube manometers and elastic type gauges), temperature (i.e. glass thermometer, bi-metallic strip thermometer, filled system thermometer, vapor pressure thermometer), level, and flow measuring devices. The book describes other miscellaneous instruments, signal transmitting devices, supply and control systems, and monitoring systems. The theory of automatic control and semi-conductor devices are also considered. Marine engineers will find the book useful.

Software life cycle process and classification guides for KNICS digital instrumentation and control system design

Energy Technology Data Exchange (ETDEWEB)

Lee, Jang Soo; Son, Han Seung; Kim, Jang Yeol; Kwon, Kee Choon; Lee, Soon Seung; Kim, Doo Hwan [Korea Atomic Energy Research Institute, Taejeon (Korea)

2002-04-01

Documentation should exist that shows that the qualification activities have been successfully accomplished for each life cycle activity group. In particular, the documentation should show that the system safety requirements have been adequately addressed for each life cycle activity group, that no new hazards have been introduced, and that the software requirements, design elements, and code elements that can affect safety have been identified. Because the safety of software can be assured through both the process Verification and Validation (V and V) itself and the V and V of all the intermediate and final products during the software development lifecycle, the development of KNICS Software Safety Framework (KSSF) must be established. As the first activity for establishing KSSF, we have developed this report, Software Life Cycle Process and Classification Guides for KNICS Digital I and C System. This report is organized as follows. Chapter I describes the background, definitions, and references of SLCP. Chapter II describes KNICS safety software categorization. In Chapter III, we define the requirements on software life cycle process for designing digital KNICS. Chapter III.3, that is the main section of the chapter, includes the requirements for software life cycle process planning, the requirements for software life cycle process implementation, and the requirements for software life cycle process design outputs. Finally, we have described the result of a case study on the SLCP for developing the software of ESF-CCS system that is being developed by a private company, BNF. 29 refs., 5 figs., 7 tabs. (Author)

Teaching computer interfacing with virtual instruments in an object-oriented language.

Science.gov (United States)

Gulotta, M

1995-01-01

LabVIEW is a graphic object-oriented computer language developed to facilitate hardware/software communication. LabVIEW is a complete computer language that can be used like Basic, FORTRAN, or C. In LabVIEW one creates virtual instruments that aesthetically look like real instruments but are controlled by sophisticated computer programs. There are several levels of data acquisition VIs that make it easy to control data flow, and many signal processing and analysis algorithms come with the software as premade VIs. In the classroom, the similarity between virtual and real instruments helps students understand how information is passed between the computer and attached instruments. The software may be used in the absence of hardware so that students can work at home as well as in the classroom. This article demonstrates how LabVIEW can be used to control data flow between computers and instruments, points out important features for signal processing and analysis, and shows how virtual instruments may be used in place of physical instrumentation. Applications of LabVIEW to the teaching laboratory are also discussed, and a plausible course outline is given. PMID:8580361

Sulfur Dioxide Analyzer Instrument Handbook

Energy Technology Data Exchange (ETDEWEB)

Springston, Stephen R. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2016-05-01

The Sulfur Dioxide Analyzer measures sulfur dioxide based on absorbance of UV light at one wavelength by SO₂ molecules which then decay to a lower energy state by emitting UV light at a longer wavelength. Specifically, SO₂ + hυ1 →SO₂ *→SO₂ + hυ2 The emitted light is proportional to the concentration of SO₂ in the optical cell. External communication with the analyzer is available through an Ethernet port configured through the instrument network of the AOS systems. The Model 43i-TLE is part of the i-series of Thermo Scientific instruments. The i-series instruments are designed to interface with external computers through the proprietary Thermo Scientific iPort Software. However, this software is somewhat cumbersome and inflexible. Brookhaven National Laboratory (BNL) has written an interface program in National Instruments LabView that both controls the Model 43i-TLE Analyzer AND queries the unit for all measurement and housekeeping data. The LabView vi (the software program written by BNL) ingests all raw data from the instrument and outputs raw data files in a uniform data format similar to other instruments in the AOS and described more fully in Section 6.0 below.

Portability scenarios for intelligent robotic control agent software

Science.gov (United States)

Straub, Jeremy

2014-06-01

Portability scenarios are critical in ensuring that a piece of AI control software will run effectively across the collection of craft that it is required to control. This paper presents scenarios for control software that is designed to control multiple craft with heterogeneous movement and functional characteristics. For each prospective target-craft type, its capabilities, mission function, location, communications capabilities and power profile are presented and performance characteristics are reviewed. This work will inform future work related to decision making related to software capabilities, hardware control capabilities and processing requirements.

Study on the communication technology of instrument based on LabVIEW

International Nuclear Information System (INIS)

Jiang Wei; Lai Qinggui; Zhang Xiaobo

2012-01-01

The hardware and software structure of communication of universal instrument is discussed based on LabVIEW, the several realization of remote communication is compared too. In the control and measure system of LIA, using LabVIEW, the communication is realized among the plenty of instruments which have the various interfaces, in this paper the frame of hardware and software about instrument communication is showed. (authors)

Framework for Small-Scale Experiments in Software Engineering: Guidance and Control Software Project: Software Engineering Case Study

Science.gov (United States)

Hayhurst, Kelly J.

1998-01-01

Software is becoming increasingly significant in today's critical avionics systems. To achieve safe, reliable software, government regulatory agencies such as the Federal Aviation Administration (FAA) and the Department of Defense mandate the use of certain software development methods. However, little scientific evidence exists to show a correlation between software development methods and product quality. Given this lack of evidence, a series of experiments has been conducted to understand why and how software fails. The Guidance and Control Software (GCS) project is the latest in this series. The GCS project is a case study of the Requirements and Technical Concepts for Aviation RTCA/DO-178B guidelines, Software Considerations in Airborne Systems and Equipment Certification. All civil transport airframe and equipment vendors are expected to comply with these guidelines in building systems to be certified by the FAA for use in commercial aircraft. For the case study, two implementations of a guidance and control application were developed to comply with the DO-178B guidelines for Level A (critical) software. The development included the requirements, design, coding, verification, configuration management, and quality assurance processes. This paper discusses the details of the GCS project and presents the results of the case study.

Managing Complexity of Control Software through Concurrency

NARCIS (Netherlands)

Hilderink, G.H.

2005-01-01

In this thesis, we are concerned with the development of concurrent software for embedded systems. The emphasis is on the development of control software. Embedded systems are concurrent systems whereby hardware and software communicate with the concurrent world. Concurrency is essential, which

The predictive power of SIMION/SDS simulation software for modeling ion mobility spectrometry instruments

Science.gov (United States)

Lai, Hanh; McJunkin, Timothy R.; Miller, Carla J.; Scott, Jill R.; Almirall, José R.

2008-09-01

The combined use of SIMION 7.0 and the statistical diffusion simulation (SDS) user program in conjunction with SolidWorks® with COSMSOSFloWorks® fluid dynamics software to model a complete, commercial ion mobility spectrometer (IMS) was demonstrated for the first time and compared to experimental results for tests using compounds of immediate interest in the security industry (e.g., 2,4,6-trinitrotoluene, 2,7-dinitrofluorene, and cocaine). The effort of this research was to evaluate the predictive power of SIMION/SDS for application to IMS instruments. The simulation was evaluated against experimental results in three studies: (1) a drift:carrier gas flow rates study assesses the ability of SIMION/SDS to correctly predict the ion drift times; (2) a drift gas composition study evaluates the accuracy in predicting the resolution; (3) a gate width study compares the simulated peak shape and peak intensity with the experimental values. SIMION/SDS successfully predicted the correct drift time, intensity, and resolution trends for the operating parameters studied. Despite the need for estimations and assumptions in the construction of the simulated instrument, SIMION/SDS was able to predict the resolution between two ion species in air within 3% accuracy. The preliminary success of IMS simulations using SIMION/SDS software holds great promise for the design of future instruments with enhanced performance.

Software Authentication

International Nuclear Information System (INIS)

Wolford, J.K.; Geelhood, B.D.; Hamilton, V.A.; Ingraham, J.; MacArthur, D.W.; Mitchell, D.J.; Mullens, J.A.; Vanier, P. E.; White, G.K.; Whiteson, R.

2001-01-01

The effort to define guidance for authentication of software for arms control and nuclear material transparency measurements draws on a variety of disciplines and has involved synthesizing established criteria and practices with newer methods. Challenges include the need to protect classified information that the software manipulates as well as deal with the rapid pace of innovation in the technology of nuclear material monitoring. The resulting guidance will shape the design of future systems and inform the process of authentication of instruments now being developed. This paper explores the technical issues underlying the guidance and presents its major tenets

A new development on measurement and control software of SANS BATAN spectrometer (SMARTer) in Serpong, Indonesia

Science.gov (United States)

Bharoto, Suparno, Nadi; Putra, Edy Giri Rachman

2015-04-01

In 2005, the main computer for data acquisition and control system of Small-angle Neutron Scattering (SANS) BATAN Spectrometer (SMARTer) was replaced since it halted to operate the spectrometer. According to this replacement, the new software for data acquisition and control system has been developed in-house. Visual Basic programming language is used in developing the software. In the last two years, many developments have been made both in the hardware and also the software to conduct the experiment is more effective and efficient. Lately, the previous motor controller card (ISA Card) was replaced with the programmable motor controller card (PCI Card) for driving one motor of position sensitive detector (PSD), eight motors of four collimators, and six motors of six pinhole discs. This new control system software makes all motors can be moved simultaneously, then it reduces significantly the consuming time of setting up the instrument before running the experiment. Along with that development, the new data acquisition software under MS Windows operating system is also developed to drive a beam stopper in X-Y directions as well as to read the equipment status such as position of the collimators and PSD, to acquire neutron counts on monitor and PSD detectors, and also to manage 12 samples position automatically. A timer object which is set in one second to read the equipment status via serial port of the computer (RS232C), and general purpose interface board (GPIB) for reading the total counts of each pixel of the PSD from histogram memory was used in this new software. The experiment result displayed in real time on the main window, and the data is saved in the special format for further data reduction and analysis. The new software has been implemented and performed for experiment using a preset count or preset time mode for absolute scattering intensity method.

A new development on measurement and control software of SANS BATAN spectrometer (SMARTer) in Serpong, Indonesia

Energy Technology Data Exchange (ETDEWEB)

Bharoto,; Suparno, Nadi; Putra, Edy Giri Rachman [Center for Technology of Nuclear Industrial Materials, National Nuclear Energy Agency of Indonesia (BATAN) Kawasan Puspiptek Serpong, Tangerang 15314, Banten, Indonesia bharoto@batan.go.id (Indonesia)

2015-04-16

In 2005, the main computer for data acquisition and control system of Small-angle Neutron Scattering (SANS) BATAN Spectrometer (SMARTer) was replaced since it halted to operate the spectrometer. According to this replacement, the new software for data acquisition and control system has been developed in-house. Visual Basic programming language is used in developing the software. In the last two years, many developments have been made both in the hardware and also the software to conduct the experiment is more effective and efficient. Lately, the previous motor controller card (ISA Card) was replaced with the programmable motor controller card (PCI Card) for driving one motor of position sensitive detector (PSD), eight motors of four collimators, and six motors of six pinhole discs. This new control system software makes all motors can be moved simultaneously, then it reduces significantly the consuming time of setting up the instrument before running the experiment. Along with that development, the new data acquisition software under MS Windows operating system is also developed to drive a beam stopper in X-Y directions as well as to read the equipment status such as position of the collimators and PSD, to acquire neutron counts on monitor and PSD detectors, and also to manage 12 samples position automatically. A timer object which is set in one second to read the equipment status via serial port of the computer (RS232C), and general purpose interface board (GPIB) for reading the total counts of each pixel of the PSD from histogram memory was used in this new software. The experiment result displayed in real time on the main window, and the data is saved in the special format for further data reduction and analysis. The new software has been implemented and performed for experiment using a preset count or preset time mode for absolute scattering intensity method.

Virtual instrument for controlling and monitoring digitalized power supply in SSRF

International Nuclear Information System (INIS)

Tang Junlong; Chen Huanguang; Chinese Academy of Sciences, Beijing; Xu Ruinian; Shen Tianjian; Li Deming

2006-01-01

The Shanghai Synchrotron Radiation Facility (SSRF) needs extremely precise power supplies for their various magnets. A digital controller is being developed for the power converters of the SSRF power supply (PS). In the digital controller, a fully digital pulse-width modulator (PWM) directly controls the power unit insulated gate bipolar transistor (IGBT) of the PS. A program in LabVIEW language has been developed to control and monitor the digital PS via serial communication (RS232) from a PC and to modify its parameters as well. In this article, the software design of the virtual instrument for controlling and monitoring digitalized PS and its associated functions are described, and the essential elements of the program graphical main-VI and sub-VI source code are presented and explained. The communication protocol and the structure of the developed system are also included in this article. (authors)

A NEW CONTROL CIRCUIT AND COMPUTER SOFTWARE FOR CONTROLING PHOTOVOLTAIC SYSTEMS

Directory of Open Access Journals (Sweden)

Mustafa Berkant SELEK

2008-02-01

Full Text Available In this study, a new microcontroller circuit was designed and new computer software was implemented to control power flow currents of renewable energy system, which is established in Solar Energy Institute, Ege University, Bornova, Izmir, Turkey. PIC18F452 microcontroller based electronic circuit was designed to control another electronic circuit that includes power electronic switching components. Readily available standard control circuits are designed for switching single level inverters. In contrary, implemented circuit allows to switch multilevel inverters. In addition, because the efficiency of solar energy panels is considerably low, solar panels should be operated under the maximum power point (MPP. Therefore, MPP algorithm is included in the designed control circuit. Next, the control circuit also includes a serial communication interface based on RS232 standard. Using this interface enables the user to choose all functions available in the control circuit and take status report via computer software. Last, a general purpose command set was designed to establish communication between the computer software and the microcontroller-based control circuit. As a result, it is aimed that this study supply a basis for the researchers who want to develop own control circuits or more visual software.

Automated Cryocooler Monitor and Control System Software

Science.gov (United States)

Britchcliffe, Michael J.; Conroy, Bruce L.; Anderson, Paul E.; Wilson, Ahmad

2011-01-01

This software is used in an automated cryogenic control system developed to monitor and control the operation of small-scale cryocoolers. The system was designed to automate the cryogenically cooled low-noise amplifier system described in "Automated Cryocooler Monitor and Control System" (NPO-47246), NASA Tech Briefs, Vol. 35, No. 5 (May 2011), page 7a. The software contains algorithms necessary to convert non-linear output voltages from the cryogenic diode-type thermometers and vacuum pressure and helium pressure sensors, to temperature and pressure units. The control function algorithms use the monitor data to control the cooler power, vacuum solenoid, vacuum pump, and electrical warm-up heaters. The control algorithms are based on a rule-based system that activates the required device based on the operating mode. The external interface is Web-based. It acts as a Web server, providing pages for monitor, control, and configuration. No client software from the external user is required.

ITER instrumentation and control-Status and plans

International Nuclear Information System (INIS)

Wallander, Anders; Abadie, Lana; Dave, Haresh; Di Maio, Franck; Gulati, Hitesh Kumar; Hansalia, Chandresh; Joonekindt, Didier; Journeaux, Jean-Yves; Klotz, Wolf-Dieter; Mahajan, Kirti; Makijarvi, Petri; Scibile, Luigi; Stepanov, Denis; Utzel, Nadine; Yonekawa, Izuru

2010-01-01

The ITER instrumentation and control (I and C) system is the term encompassing all hardware and software required to operate ITER. It has two levels of hierarchy: the central I and C systems and the plant systems I and C. The central I and C systems comprise CODAC (Control, Data Access and Communication), the central interlock system (CIS) and the central safety systems (CSS). The central I and C systems are 'in-fund', i.e. procured by ITER Organization (IO), while plant systems I and C are 'in-kind', i.e. procured by the seven ITER domestic agencies. This procurement model, together with the current estimate of 161 plant systems I and C, poses a major challenge for the realization and integration of the ITER I and C system. To address this challenge a main strategic focus of the CODAC group, formed in 2008, has been to establish good relations with the domestic agencies. By distributing the required R and D tasks and contracts fairly between the domestic agencies we build collaborations for the future at the same time as technical work proceed. The primary goal of ITER I and C system is to provide a fully integrated and automated control system for ITER. Standardization of plant systems I and C is of primary importance and has been the highest priority task during the last year. The target of associated R and D activities is to survey, benchmark and prototype main stream technologies, in order to choose the best and most widely used technology standards for plant systems I and C. In this paper we elaborate on our approach, both from a technical and a non-technical perspective, explain technology evaluation and decisions and finally present the way forward to ensure ITER I and C system will contribute and be instrumental in making ITER a success.

Design of LabVIEW®-based software for the control of sequential injection analysis instrumentation for the determination of morphine

Science.gov (United States)

Lenehan, Claire E.; Lewis, Simon W.

2002-01-01

LabVIEW®-based software for the automation of a sequential injection analysis instrument for the determination of morphine is presented. Detection was based on its chemiluminescence reaction with acidic potassium permanganate in the presence of sodium polyphosphate. The calibration function approximated linearity (range 5 × 10-10 to 5 × 10-6 M) with a line of best fit of y=1.05x+8.9164 (R2 =0.9959), where y is the log10 signal (mV) and x is the log10 morphine concentration (M). Precision, as measured by relative standard deviation, was 0.7% for five replicate analyses of morphine standard (5 × 10-8 M). The limit of detection (3σ) was determined as 5 × 10-11 M morphine. PMID:18924729

Design of LabVIEW-based software for the control of sequential injection analysis instrumentation for the determination of morphine.

Science.gov (United States)

Lenehan, Claire E; Barnett, Neil W; Lewis, Simon W

2002-01-01

LabVIEW-based software for the automation of a sequential injection analysis instrument for the determination of morphine is presented. Detection was based on its chemiluminescence reaction with acidic potassium permanganate in the presence of sodium polyphosphate. The calibration function approximated linearity (range 5 x 10(-10) to 5 x 10(-6) M) with a line of best fit of y=1.05(x)+8.9164 (R(2) =0.9959), where y is the log10 signal (mV) and x is the log10 morphine concentration (M). Precision, as measured by relative standard deviation, was 0.7% for five replicate analyses of morphine standard (5 x 10(-8) M). The limit of detection (3sigma) was determined as 5 x 10(-11) M morphine.

Real world instrumentation with Python automated data acquisition and control systems

CERN Document Server

Hughes, John

2010-01-01

Learn how to develop your own applications to monitor or control instrumentation hardware. Whether you need to acquire data from a device or automate its functions, this practical book shows you how to use Python's rapid development capabilities to build interfaces that include everything from software to wiring. You get step-by-step instructions, clear examples, and hands-on tips for interfacing a PC to a variety of devices. Use the book's hardware survey to identify the interface type for your particular device, and then follow detailed examples to develop an interface with Python and C. O

An improved instrument setpoint control program

International Nuclear Information System (INIS)

Cash, J.S. Jr.; George, R.T.; Kincaid, S.C.

1991-01-01

Instrument setpoints have a definite and often significant impact on plant safety, reliability, and availability. Although typically overshadowed by plant design, modification, and physical change activities, instrument setpoints can alter plant status and system operating characteristics just as significantly. Recognizing the need for a formal program that provides configuration control of instrument setpoints, provides a readily accessible and clearly documented basis for instrument setpoints, and integrates and coordinates operations, engineering, and maintenance activities that influence the basis for instrument setpoints, Philadelphia Electric Company (PECo) is developing an Improved Instrument Setpoint Control Program (IISCP) that incorporates current industry guidance and practices and state-of-the-art information systems technology. The IISCP was designed around PECo's then existing business processes for setpoint control, determination, and maintenance. A task force representing the various constituencies from both plants and the engineering and services organizations were formed to identify objectives and design features for the IISCP. Utilizing industry standards and guidance, regulatory documents, the experiences and good practices obtained from other utilities, and PECo's nuclear group strategies, objectives, and goals, specific objectives were identified to enhance the business processes

The potential of soft computing methods in NPP instrumentation and control

International Nuclear Information System (INIS)

Hampel, R.; Chaker, N.; Kaestner, W.; Traichel, A.; Wagenknecht, M.; Gocht, U.

2002-01-01

The method of signal processing by soft computing include the application of fuzzy logic, synthetic neural networks, and evolutionary algorithms. The article contains an outline of the objectives and results of the application of fuzzy logic and methods of synthetic neural networks in nuclear measurement and control. The special requirements to be met by the software in safety-related areas with respect to reliability, evaluation, and validation are described. Possible uses may be in off-line applications in modeling, simulation, and reliability analysis as well as in on-line applications (real-time systems) for instrumentation and control. Safety-related aspects of signal processing are described and analyzed for the fuzzy logic and synthetic neural network concepts. Application are covered in selected examples. (orig.)

Core Community Specifications for Electron Microprobe Operating Systems: Software, Quality Control, and Data Management Issues

Science.gov (United States)

Fournelle, John; Carpenter, Paul

2006-01-01

Modem electron microprobe systems have become increasingly sophisticated. These systems utilize either UNIX or PC computer systems for measurement, automation, and data reduction. These systems have undergone major improvements in processing, storage, display, and communications, due to increased capabilities of hardware and software. Instrument specifications are typically utilized at the time of purchase and concentrate on hardware performance. The microanalysis community includes analysts, researchers, software developers, and manufacturers, who could benefit from exchange of ideas and the ultimate development of core community specifications (CCS) for hardware and software components of microprobe instrumentation and operating systems.

Guidance and Control Software Project Data - Volume 1: Planning Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the planning documents from the GCS project. Volume 1 contains five appendices: A. Plan for Software Aspects of Certification for the Guidance and Control Software Project; B. Software Development Standards for the Guidance and Control Software Project; C. Software Verification Plan for the Guidance and Control Software Project; D. Software Configuration Management Plan for the Guidance and Control Software Project; and E. Software Quality Assurance Activities.

Software for Embedded Control Systems

NARCIS (Netherlands)

Broenink, Johannes F.; Hilderink, G.H.; Jovanovic, D.S.

2001-01-01

The research of our team deals with the realization of control schemes on digital computers. As such the emphasis is on embedded control software implementation. Applications are in the field of mechatronic devices, using a mechatronic design approach (the integrated and optimal design of a

Integrating software reliability concepts into risk and reliability modeling of digital instrumentation and control systems used in nuclear power plants

International Nuclear Information System (INIS)

Arndt, S. A.

2006-01-01

As software-based digital systems are becoming more and more common in all aspects of industrial process control, including the nuclear power industry, it is vital that the current state of the art in quality, reliability, and safety analysis be advanced to support the quantitative review of these systems. Several research groups throughout the world are working on the development and assessment of software-based digital system reliability methods and their applications in the nuclear power, aerospace, transportation, and defense industries. However, these groups are hampered by the fact that software experts and probabilistic safety assessment experts view reliability engineering very differently. This paper discusses the characteristics of a common vocabulary and modeling framework. (authors)

30 CFR 77.314 - Automatic temperature control instruments.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic temperature control instruments. 77... UNDERGROUND COAL MINES Thermal Dryers § 77.314 Automatic temperature control instruments. (a) Automatic temperature control instruments for thermal dryer system shall be of the recording type. (b) Automatic...

Advances in control and instrumentation

International Nuclear Information System (INIS)

Surendar, Ch.

1994-01-01

Control and instrumentation systems have seen significant changes from pneumatic to electronic with the advent of transistors and integrated circuits. Miniaturization was realised. With the introduction of microprocessors there has been a revolutionary change in the approach in instrumentation and control systems in the areas of sensors, data acquisition/transmission, processing for control, and presentation of the information to the operator. An effort is made to give some insight into these areas, with some idea of the advantages to which these systems are being put to use in the nuclear facilities, particularly nuclear power reactors. (author)

Feedback control of acoustic musical instruments: collocated control using physical analogs.

Science.gov (United States)

Berdahl, Edgar; Smith, Julius O; Niemeyer, Günter

2012-01-01

Traditionally, the average professional musician has owned numerous acoustic musical instruments, many of them having distinctive acoustic qualities. However, a modern musician could prefer to have a single musical instrument whose acoustics are programmable by feedback control, where acoustic variables are estimated from sensor measurements in real time and then fed back in order to influence the controlled variables. In this paper, theory is presented that describes stable feedback control of an acoustic musical instrument. The presentation should be accessible to members of the musical acoustics community who may have limited or no experience with feedback control. First, the only control strategy guaranteed to be stable subject to any musical instrument mobility is described: the sensors and actuators must be collocated, and the controller must emulate a physical analog system. Next, the most fundamental feedback controllers and the corresponding physical analog systems are presented. The effects that these controllers have on acoustic musical instruments are described. Finally, practical design challenges are discussed. A proof explains why changing the resonance frequency of a musical resonance requires much more control power than changing the decay time of the resonance. © 2012 Acoustical Society of America.

Project C-018H, 242-A evaporator/PUREX Plant Process Condensate Treatment Facility Instrumentation and Control (I ampersand C)

International Nuclear Information System (INIS)

Dupuis, A.

1995-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the Collection System Instrumentation ampersand Control System for Project C-018H performs according to design. Specifically, this ATP is designed to verify the following overall system requirements: The input and outputs properly connected to the LCU terminal strips. The control system software conforms to the configuration specified by the logic diagrams, piping and instrumentation diagrams (P ampersand ID), and the LERF operating philosophy. Testing will be performed using actual signals. If actual signals are not available, then simulated signals will be used to complete the tests

X-ray spectrometer instrumentation with a personal computer

International Nuclear Information System (INIS)

Skaarup, P.; Vogeley, E.

1989-01-01

A description is given of an instrumentation for control of an X-ray spectrometer used in solid state physics experiments. The instrumentation includes a personal computer (PC) and a European Computer Bus (ECB) interface system. Details are given of the operating software. (author)

A flexible software architecture for tokamak discharge control systems

International Nuclear Information System (INIS)

Ferron, J.R.; Penaflor, B.; Walker, M.L.; Moller, J.; Butner, D.

1995-01-01

The software structure of the plasma control system in use on the DIII-D tokamak experiment is described. This system implements control functions through software executing in real time on one or more digital computers. The software is organized into a hierarchy that allows new control functions needed to support the DIII-D experimental program to be added easily without affecting previously implemented functions. This also allows the software to be portable in order to create control systems for other applications. The tokamak operator uses an X-windows based interface to specify the time evolution of a tokamak discharge. The interface provides a high level view for the operator that reduces the need for detailed knowledge of the control system operation. There is provision for an asynchronous change to an alternate discharge time evolution in response to an event that is detected in real time. Quality control is enhanced through off-line testing that can make use of software-based tokamak simulators

Prometheus Reactor I&C Software Development Methodology, for Action

Energy Technology Data Exchange (ETDEWEB)

T. Hamilton

2005-07-30

The purpose of this letter is to submit the Reactor Instrumentation and Control (I&C) software life cycle, development methodology, and programming language selections and rationale for project Prometheus to NR for approval. This letter also provides the draft Reactor I&C Software Development Process Manual and Reactor Module Software Development Plan to NR for information.

Integrating a flexible modeling framework (FMF) with the network security assessment instrument to reduce software security risk

Science.gov (United States)

Gilliam, D. P.; Powell, J. D.

2002-01-01

This paper presents a portion of an overall research project on the generation of the network security assessment instrument to aid developers in assessing and assuring the security of software in the development and maintenance lifecycles.

Fusion instrumentation and control: a development strategy

International Nuclear Information System (INIS)

Hsu, P.Y.; Greninger, R.C.; Longhurst, G.R.; Madden, P.

1981-01-01

We have examined requirements for a fusion instrumentation and control development program to determine where emphasis is needed. The complex, fast, and closely coupled system dynamics of fusion reactors reveal a need for a rigorous approach to the development of instrumentation and control systems. A framework for such a development program should concentrate on three principal need areas: the operator-machine interface, the data and control system architecture, and fusion compatible instruments and sensors. System dynamics characterization of the whole fusion reactor system is also needed to facilitate the implementation process in each of these areas. Finally, the future need to make the instrumentation and control system compatible with the requirements of a commercial plant is met by applying transition technology. These needs form the basis for the program tasks suggested

Development of a nuclear reactor control system simulator using virtual instruments

International Nuclear Information System (INIS)

Pinto, Antonio Juscelino; Mesquita, Amir Zacarias; Lameiras, Fernando Soares

2011-01-01

The International Atomic Energy Agency recommends the use of safety and friendly interfaces for monitoring and controlling the operational parameters of the nuclear reactors. This article describes a digital system being developed to simulate the behavior of the operating parameters using virtual instruments. The control objective is to bring the reactor power from its source level (mW) to a full power (kW). It is intended for education of basic reactor neutronic and thermohydraulic principles such as the multiplication factor, criticality, reactivity, period, delayed neutron, control by rods, fuel and coolant temperatures, power, etc. The 250 kW IPR-R1 TRIGA research reactor at Nuclear Technology Development Centre - CDTN was used as reference. TRIGA reactors, developed by General Atomics (GA), are the most widely used research reactor in the world. The simulator system is being developed using the LabVIEW (Laboratory Virtual Instruments Engineering Workbench) software, considering the modern concept of virtual instruments (VI's) using electronic processor and visual interface in video monitor. The main purpose of the system is to provide training tools for instructors and students, allowing navigating by user-friendly operator interface and monitoring tendencies of the operational variables. It will be an interactive tool for training and teaching and could be used to predict the reactor behavior. Some scenarios are presented to demonstrate that it is possible to know the behavior of some variables from knowledge of input parameters. The TRIGA simulator system will allow the study of parameters, which affect the reactor operation, without the necessity of using the facility. (author)

Development of a nuclear reactor control system simulator using virtual instruments

Energy Technology Data Exchange (ETDEWEB)

Pinto, Antonio Juscelino; Mesquita, Amir Zacarias; Lameiras, Fernando Soares, E-mail: ajp@cdtn.b, E-mail: amir@cdtn.b, E-mail: fsl@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2011-07-01

The International Atomic Energy Agency recommends the use of safety and friendly interfaces for monitoring and controlling the operational parameters of the nuclear reactors. This article describes a digital system being developed to simulate the behavior of the operating parameters using virtual instruments. The control objective is to bring the reactor power from its source level (mW) to a full power (kW). It is intended for education of basic reactor neutronic and thermohydraulic principles such as the multiplication factor, criticality, reactivity, period, delayed neutron, control by rods, fuel and coolant temperatures, power, etc. The 250 kW IPR-R1 TRIGA research reactor at Nuclear Technology Development Centre - CDTN was used as reference. TRIGA reactors, developed by General Atomics (GA), are the most widely used research reactor in the world. The simulator system is being developed using the LabVIEW (Laboratory Virtual Instruments Engineering Workbench) software, considering the modern concept of virtual instruments (VI's) using electronic processor and visual interface in video monitor. The main purpose of the system is to provide training tools for instructors and students, allowing navigating by user-friendly operator interface and monitoring tendencies of the operational variables. It will be an interactive tool for training and teaching and could be used to predict the reactor behavior. Some scenarios are presented to demonstrate that it is possible to know the behavior of some variables from knowledge of input parameters. The TRIGA simulator system will allow the study of parameters, which affect the reactor operation, without the necessity of using the facility. (author)

Distributed control software of high-performance control-loop algorithm

CERN Document Server

Blanc, D

1999-01-01

The majority of industrial cooling and ventilation plants require the control of complex processes. All these processes are highly important for the operation of the machines. The stability and reliability of these processes are leading factors identifying the quality of the service provided. The control system architecture and software structure, as well, are required to have high dynamical performance and robust behaviour. The intelligent systems based on PID or RST controllers are used for their high level of stability and accuracy. The design and tuning of these complex controllers require the dynamic model of the plant to be known (generally obtained by identification) and the desired performance of the various control loops to be specified for achieving good performances. The concept of having a distributed control algorithm software provides full automation facilities with well-adapted functionality and good performances, giving methodology, means and tools to master the dynamic process optimization an...

Preparing and Conducting Review Missions of Instrumentation and Control Systems in Nuclear Power Plants

International Nuclear Information System (INIS)

2016-07-01

The IERICS (Independent Engineering Review of Instrumentation and Control Systems) mission is a comprehensive engineering review service directly addressing strategy and the key elements for implementation of modern instrumentation and control (I&C) systems, noting in applicable cases, specific concerns related to the implementation of advanced digital I&C systems and the use of software and/or digital logic in safety applications of a nuclear power plant. The guidelines outlined in this publication provide a basic structure, common reference and checklist across the various areas covered by an IERICS mission. Publications referenced in these guidelines could provide additional useful information for the counterpart while preparing for the IERICS mission. A structure for the mission report is given in the Appendix. In 2016, this publication was revised by international experts who had participated in previous IERICS missions. The revision reflects experiences and lessons learned from the preparation and conduct of those missions

Packaging of control system software

International Nuclear Information System (INIS)

Zagar, K.; Kobal, M.; Saje, N.; Zagar, A.; Sabjan, R.; Di Maio, F.; Stepanov, D.

2012-01-01

Control system software consists of several parts - the core of the control system, drivers for integration of devices, configuration for user interfaces, alarm system, etc. Once the software is developed and configured, it must be installed to computers where it runs. Usually, it is installed on an operating system whose services it needs, and also in some cases dynamically links with the libraries it provides. Operating system can be quite complex itself - for example, a typical Linux distribution consists of several thousand packages. To manage this complexity, we have decided to rely on Red Hat Package Management system (RPM) to package control system software, and also ensure it is properly installed (i.e., that dependencies are also installed, and that scripts are run after installation if any additional actions need to be performed). As dozens of RPM packages need to be prepared, we are reducing the amount of effort and improving consistency between packages through a Maven-based infrastructure that assists in packaging (e.g., automated generation of RPM SPEC files, including automated identification of dependencies). So far, we have used it to package EPICS, Control System Studio (CSS) and several device drivers. We perform extensive testing on Red Hat Enterprise Linux 5.5, but we have also verified that packaging works on CentOS and Scientific Linux. In this article, we describe in greater detail the systematic system of packaging we are using, and its particular application for the ITER CODAC Core System. (authors)

Guidance and Control Software Project Data - Volume 3: Verification Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the verification documents from the GCS project. Volume 3 contains four appendices: A. Software Verification Cases and Procedures for the Guidance and Control Software Project; B. Software Verification Results for the Pluto Implementation of the Guidance and Control Software; C. Review Records for the Pluto Implementation of the Guidance and Control Software; and D. Test Results Logs for the Pluto Implementation of the Guidance and Control Software.

Neutron beam applications - Polymer study and sample environment development for HANARO SANS instrument

Energy Technology Data Exchange (ETDEWEB)

Kim, Hong Doo [Kyunghee University, Seoul (Korea); Char, Kook Heon [Seoul National University, Seoul (Korea)

2000-04-01

A new SANS instrument will be installed in HANARO reactor near future and in parallel it is necessary to develop the sample environment facilities. One of the basic items is the equipment to control the sample temperature of cell block with auto-sample changer. It is required to develop a control software for this purpose. In addition, softwares of the aquisition and analysis for SANS instrument must be developed and supplied in order to function properly. PS/PI block copolymer research in NIST will provide the general understanding of SANS instrument and instrument-related valuable informations such as standard sample for SANS and know-hows of the instrument building. The following are the results of this research. a. Construction of sample cell block. b. Software to control the temperature and auto-sample changer. c. Acquisition of the SANS data analysis routine and its modification for HANARO SANS. d. PS/PI block copolymer research in NIST. e. Calibration data of NIST and HANARO SANS for comparison. 39 figs., 2 tabs. (Author)

Neutronic control instrumentation of protection systems

International Nuclear Information System (INIS)

Furet, J.

1977-01-01

The aims of neutronic control instrumentation are briefly recalled and the present status of materials research and development is presented. As for the out-of-pile instrumentation, emphasis is put on the reliability and efficiency of the detectors and the new solutions of electric signal processing. The possible reactivity measurements at rest are examined. As for in-pile instrumentation results relating to mobile detectors of the type of miniaturized fission chambers are presented. The radiation tests on course of development for several years in the working conditions of neutron self-powdered detectors are analyzed so as to show that their use as built-in in-core instrumentation is to be envisaged at short term. Basic options inherent to the 'Nuclear Safety' philosophy that define the protection system are recalled. A definition and a justification of the performance testing of the instrumentation at rest and in-service are then derived. Some new solutions are envisaged for processing the digital data obtained from the various sensors . A quality control of the materials setting conditions (especially electric noise) ensures a high reliability and availability of the materials involved in the neutron control and the protection system in working conditions [fr

Effective Development and Verification of Railway Control Software

DEFF Research Database (Denmark)

Haxthausen, Anne Elisabeth

2011-01-01

This document presents a method for effective development of software for a product line of similar railway control systems. The software is constructed in three steps: first a specifications in a domain-specific language is created, then a formal behavioural controller model is automatically...

Imaging Sensor Flight and Test Equipment Software

Science.gov (United States)

Freestone, Kathleen; Simeone, Louis; Robertson, Byran; Frankford, Maytha; Trice, David; Wallace, Kevin; Wilkerson, DeLisa

2007-01-01

The Lightning Imaging Sensor (LIS) is one of the components onboard the Tropical Rainfall Measuring Mission (TRMM) satellite, and was designed to detect and locate lightning over the tropics. The LIS flight code was developed to run on a single onboard digital signal processor, and has operated the LIS instrument since 1997 when the TRMM satellite was launched. The software provides controller functions to the LIS Real-Time Event Processor (RTEP) and onboard heaters, collects the lightning event data from the RTEP, compresses and formats the data for downlink to the satellite, collects housekeeping data and formats the data for downlink to the satellite, provides command processing and interface to the spacecraft communications and data bus, and provides watchdog functions for error detection. The Special Test Equipment (STE) software was designed to operate specific test equipment used to support the LIS hardware through development, calibration, qualification, and integration with the TRMM spacecraft. The STE software provides the capability to control instrument activation, commanding (including both data formatting and user interfacing), data collection, decompression, and display and image simulation. The LIS STE code was developed for the DOS operating system in the C programming language. Because of the many unique data formats implemented by the flight instrument, the STE software was required to comprehend the same formats, and translate them for the test operator. The hardware interfaces to the LIS instrument using both commercial and custom computer boards, requiring that the STE code integrate this variety into a working system. In addition, the requirement to provide RTEP test capability dictated the need to provide simulations of background image data with short-duration lightning transients superimposed. This led to the development of unique code used to control the location, intensity, and variation above background for simulated lightning strikes

Nuclear Power Plant Control and Instrumentation activities in the United Kingdom

International Nuclear Information System (INIS)

Goodings, A.

1990-01-01

The paper describes the status of the NPP control and instrumentation in the United Kingdom. The general technology underlying most aspects of power reactor C and I in the UK has not altered since the last progress report although there have been many improvements in detail. In one field, however, that of computer applications, the change has almost been one of kind rather than degree. The following fields are briefly described: The status of nuclear power in the UK, the development of sensors, the development of electronic equipment, signal processing - information technology, quality assurance and the validation and verification of software, expert systems, training simulators. (author). 1 ref

PEP instrumentation and control system

Energy Technology Data Exchange (ETDEWEB)

Melen, R.

1980-06-01

This paper describes the operating characteristics of the primary components that form the PEP Instrumentation and Control System. Descriptions are provided for the computer control system, beam monitors, and other support systems.

PEP instrumentation and control system

International Nuclear Information System (INIS)

Melen, R.

1980-06-01

This paper describes the operating characteristics of the primary components that form the PEP Instrumentation and Control System. Descriptions are provided for the computer control system, beam monitors, and other support systems

A software architecture for a transportation control tower

NARCIS (Netherlands)

Baumgrass, A.; Dijkman, R.M.; Grefen, P.W.P.J.; Pourmirza, S.; Völzer, H.; Weske, M.H.

2014-01-01

A Transportation Control Tower is a software application that facilitates transportation planners with easily monitoring and dispatching transportation resources. This paper presents a software architecture for such an application. It focuses in particular on the novel aspects of the software

New technology in nuclear power plant instrumentation and control

International Nuclear Information System (INIS)

Anon.

1985-01-01

The primary topic of this book is what can be done to improve nuclear power plant operation safety and the economic benefits that can be gained with the utilization of advance instrumentation and control technology. Other topics discussed are the industry's reluctance to accept new designs determining cost effective improvements, and difficulties in meeting regulatory standards with new technology control. The subjects will be useful when considering the area of instrumentation and control for enhancing plant operation and safety. Contents: Advanced Instrumention, Plant Control and Monitoring, Plant Diagnostics and Failure Detection, Human Factors Considerations in Instrumentation and Control, NRC and Industry Perspective on Advanced Instrumentation and Control

Controlling S2 terminal using FS software

Science.gov (United States)

Xue, Zhuhe

New S2FS software for controlling S2 terminal of Sheshan station has been developed. It works under Field System software. All S2 operation commands are incorporated in a station program. The interface of SWT computer and S2 terminal is RS232 interface. S2FS software is designed by using Shell and C language. It has been used in VSOP experiments.

EDS operator and control software

International Nuclear Information System (INIS)

Ott, L.L.

1985-04-01

The Enrichment Diagnostic System (EDS) was developed at Lawrence Livermore National Laboratory (LLNL) to acquire, display and analyze large quantities of transient data for a real-time Advanced Vapor Laser Isotope Separation (AVLIS) experiment. Major topics discussed in this paper are the EDS operator interface (SHELL) program, the data acquisition and analysis scheduling software, and the graphics software. The workstation concept used in EDS, the software used to configure a user's workstation, and the ownership and management of a diagnostic are described. An EDS diagnostic is a combination of hardware and software designed to study specific aspects of the process. Overall system performance is discussed from the standpoint of scheduling techniques, evaluation tools, optimization techniques, and program-to-program communication methods. EDS is based on a data driven design which keeps the need to modify software to a minimum. This design requires a fast and reliable data base management system. A third party data base management product, Berkeley Software System Database, written explicitly for HP1000's, is used for all EDS data bases. All graphics is done with an in-house graphics product, Device Independent Graphics Library (DIGLIB). Examples of devices supported by DIGLIB are: Versatec printer/plotters, Raster Technologies Graphic Display Controllers, and HP terminals (HP264x and HP262x). The benefits derived by using HP hardware and software as well as obstacles imposed by the HP environment are presented in relation to EDS development and implementation

Status report of the SRT radiotelescope control software: the DISCOS project

Science.gov (United States)

Orlati, A.; Bartolini, M.; Buttu, M.; Fara, A.; Migoni, C.; Poppi, S.; Righini, S.

2016-08-01

The Sardinia Radio Telescope (SRT) is a 64-m fully-steerable radio telescope. It is provided with an active surface to correct for gravitational deformations, allowing observations from 300 MHz to 100 GHz. At present, three receivers are available: a coaxial LP-band receiver (305-410 MHz and 1.5-1.8 GHz), a C-band receiver (5.7-7.7 GHz) and a 7-feed K-band receiver (18-26.5 GHz). Several back-ends are also available in order to perform the different data acquisition and analysis procedures requested by scientific projects. The design and development of the SRT control software started in 2004, and now belongs to a wider project called DISCOS (Development of the Italian Single-dish COntrol System), which provides a common infrastructure to the three Italian radio telescopes (Medicina, Noto and SRT dishes). DISCOS is based on the Alma Common Software (ACS) framework, and currently consists of more than 500k lines of code. It is organized in a common core and three specific product lines, one for each telescope. Recent developments, carried out after the conclusion of the technical commissioning of the instrument (October 2013), consisted in the addition of several new features in many parts of the observing pipeline, spanning from the motion control to the digital back-ends for data acquisition and data formatting; we brie y describe such improvements. More importantly, in the last two years we have supported the astronomical validation of the SRT radio telescope, leading to the opening of the first public call for proposals in late 2015. During this period, while assisting both the engineering and the scientific staff, we massively employed the control software and were able to test all of its features: in this process we received our first feedback from the users and we could verify how the system performed in a real-life scenario, drawing the first conclusions about the overall system stability and performance. We examine how the system behaves in terms of network

An instrument control and data analysis program for NMR imaging and spectroscopy

International Nuclear Information System (INIS)

Roos, M.S.; Mushlin, R.A.; Veklerov, E.; Port, J.D.; Ladd, C.; Harrison, C.G.

1988-01-01

We describe a software environment created to support real-time instrument control and signal acquisition as well as array-processor based signal and image processing in up to five dimensions. The environment is configured for NMR imaging and in vivo spectroscopy. It is designed to provide flexible tools for implementing novel NMR experiments in the research laboratory. Data acquisition and processing operations are programmed in macros which are loaded in assembled from to minimize instruction overhead. Data arrays are dynamically allocated for efficient use of memory and can be mapped directly into disk files. The command set includes primitives for real-time control of data acquisition, scalar arithmetic, string manipulation, branching, a file system and vector operations carried out by an array processor. 6 figs

GPIB based instrumentation and control system for ADITYA Thomson Scattering Diagnostic

Energy Technology Data Exchange (ETDEWEB)

Patel, Kiran, E-mail: kkpatel@ipr.res.in; Pillai, Vishal; Singh, Neha; Chaudhary, Vishnu; Thomas, Jinto; Kumar, Ajai

2016-11-15

The ADITYA Thomson Scattering Diagnostic is a single point Ruby laser based system with a spectrometer for spectral dispersion and photomultiplier tubes for the detection of scattered light. The system uses CAMAC (Computer Automated Measurement And Control) based control and data acquisition system, which synchronizes the Ruby laser, detectors and the digitizer. Previously used serial based CAMAC controller is upgraded to GPIB (General Purpose Interface Bus) based CAMAC controller for configuration and data transfer. The communication protocols for different instruments are converted to a single GPIB based for better interface. The entire control and data acquisition program is developed on LabVIEW platform for versatile operation of diagnostics with improved user friendly GUI (Graphical User Interfaces) and allows user to remotely update the laser firing time with respect to the plasma shot. The software is in handshake with the Tokamak main control program through network to minimize manual interventions for the operation of the diagnostics. The upgraded system improved the performance of the diagnostics in comparison to earlier in terms of better data transmission rate, easy to maintain and program is upgradable.

GPIB based instrumentation and control system for ADITYA Thomson Scattering Diagnostic

International Nuclear Information System (INIS)

Patel, Kiran; Pillai, Vishal; Singh, Neha; Chaudhary, Vishnu; Thomas, Jinto; Kumar, Ajai

2016-01-01

The ADITYA Thomson Scattering Diagnostic is a single point Ruby laser based system with a spectrometer for spectral dispersion and photomultiplier tubes for the detection of scattered light. The system uses CAMAC (Computer Automated Measurement And Control) based control and data acquisition system, which synchronizes the Ruby laser, detectors and the digitizer. Previously used serial based CAMAC controller is upgraded to GPIB (General Purpose Interface Bus) based CAMAC controller for configuration and data transfer. The communication protocols for different instruments are converted to a single GPIB based for better interface. The entire control and data acquisition program is developed on LabVIEW platform for versatile operation of diagnostics with improved user friendly GUI (Graphical User Interfaces) and allows user to remotely update the laser firing time with respect to the plasma shot. The software is in handshake with the Tokamak main control program through network to minimize manual interventions for the operation of the diagnostics. The upgraded system improved the performance of the diagnostics in comparison to earlier in terms of better data transmission rate, easy to maintain and program is upgradable.

ChiMS: Open-source instrument control software platform on LabVIEW for imaging/depth profiling mass spectrometers.

Science.gov (United States)

Cui, Yang; Hanley, Luke

2015-06-01

ChiMS is an open-source data acquisition and control software program written within LabVIEW for high speed imaging and depth profiling mass spectrometers. ChiMS can also transfer large datasets from a digitizer to computer memory at high repetition rate, save data to hard disk at high throughput, and perform high speed data processing. The data acquisition mode generally simulates a digital oscilloscope, but with peripheral devices integrated for control as well as advanced data sorting and processing capabilities. Customized user-designed experiments can be easily written based on several included templates. ChiMS is additionally well suited to non-laser based mass spectrometers imaging and various other experiments in laser physics, physical chemistry, and surface science.

Prometheus Reactor I and C Software Development Methodology, for Action

International Nuclear Information System (INIS)

T. Hamilton

2005-01-01

The purpose of this letter is to submit the Reactor Instrumentation and Control (I and C) software life cycle, development methodology, and programming language selections and rationale for project Prometheus to NR for approval. This letter also provides the draft Reactor I and C Software Development Process Manual and Reactor Module Software Development Plan to NR for information

Software architecture considerations for ion source control systems

International Nuclear Information System (INIS)

Sinclair, J.W.

1997-09-01

General characteristics of distributed control system software tools are examined from the perspective of ion source control system requirements. Emphasis is placed on strategies for building extensible, distributed systems in which the ion source element is one component of a larger system. Vsystem, a commercial software tool kit from Vista Control Systems was utilized extensively in the control system upgrade of the Holifield Radioactive Ion Beam Facility. Part of the control system is described and the characteristics of Vsystem are examined and compared with those of EPICS, the Experimental Physics and Industrial Control System

Simple solution to the medical instrumentation software problem

Science.gov (United States)

Leif, Robert C.; Leif, Suzanne B.; Leif, Stephanie H.; Bingue, E.

1995-04-01

Medical devices now include a substantial software component, which is both difficult and expensive to produce and maintain. Medical software must be developed according to `Good Manufacturing Practices', GMP. Good Manufacturing Practices as specified by the FDA and ISO requires the definition and compliance to a software processes which ensures quality products by specifying a detailed method of software construction. The software process should be based on accepted standards. US Department of Defense software standards and technology can both facilitate the development and improve the quality of medical systems. We describe the advantages of employing Mil-Std-498, Software Development and Documentation, and the Ada programming language. Ada provides the very broad range of functionalities, from embedded real-time to management information systems required by many medical devices. It also includes advanced facilities for object oriented programming and software engineering.

Software for NAA sample changer control

Energy Technology Data Exchange (ETDEWEB)

Dutra Neto, Aimore; Menezes, Maria Angela de B.C., E-mail: dutraa@cdtn.br, E-mail: menezes@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-RJ), Belo Horizonte, MG (Brazil)

2015-07-01

In CDTN/CNEN laboratories, the neutron activation analysis (NAA) is an analytical technique routinely employed. The irradiation is performed in the TRIGA MARK I IPR-R1 reactor. After irradiated, the samples depend of an operator to be changed, creating a bottle neck in the process. To optimize the whole process, an automation of the changing samples is necessary. In order to achieve this goal, it was developed a software to control a sample changer under construction at CDTN laboratories. Two programs, running in two different environments, manages the entire acquisition process and performs all activities necessary to move the motors to positioning the samples and control the vacuum to grip the vials. The high level routine communicates with Genie 2000 software to control a Canberra Multiport II, while a low level program controls the physical assemble. (author)

Software for NAA sample changer control

International Nuclear Information System (INIS)

Dutra Neto, Aimore; Menezes, Maria Angela de B.C.

2015-01-01

In CDTN/CNEN laboratories, the neutron activation analysis (NAA) is an analytical technique routinely employed. The irradiation is performed in the TRIGA MARK I IPR-R1 reactor. After irradiated, the samples depend of an operator to be changed, creating a bottle neck in the process. To optimize the whole process, an automation of the changing samples is necessary. In order to achieve this goal, it was developed a software to control a sample changer under construction at CDTN laboratories. Two programs, running in two different environments, manages the entire acquisition process and performs all activities necessary to move the motors to positioning the samples and control the vacuum to grip the vials. The high level routine communicates with Genie 2000 software to control a Canberra Multiport II, while a low level program controls the physical assemble. (author)

Acceptance test report MICON software exhaust fan control

International Nuclear Information System (INIS)

Keck, R.D.

1998-01-01

This test procedure specifies instructions for acceptance testing of software for exhaust fan control under Project ESPT (Energy Savings Performance Contract). The software controls the operation of two emergency exhaust fans when there is a power failure. This report details the results of acceptance testing for the MICON software upgrades. One of the modifications is that only one of the emergency fans will operate at all times. If the operating fan shuts off or fails, the other fan will start and the operating fan will be stopped

DOE Fundamentals Handbook: Instrumentation and Control, Volume 1

International Nuclear Information System (INIS)

1992-06-01

The Instrumentation and Control Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of instrumentation and control systems. The handbook includes information on temperature, pressure, flow, and level detection systems; position indication systems; process control systems; and radiation detection principles. This information will provide personnel with an understanding of the basic operation of various types of DOE nuclear facility instrumentation and control systems

DOE Fundamentals Handbook: Instrumentation and Control, Volume 1

Energy Technology Data Exchange (ETDEWEB)

1992-06-01

The Instrumentation and Control Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of instrumentation and control systems. The handbook includes information on temperature, pressure, flow, and level detection systems; position indication systems; process control systems; and radiation detection principles. This information will provide personnel with an understanding of the basic operation of various types of DOE nuclear facility instrumentation and control systems.

DOE Fundamentals Handbook: Instrumentation and Control, Volume 2

International Nuclear Information System (INIS)

1992-06-01

The Instrumentation and Control Fundamentals Handbook personnel, and the technical staff facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of instrumentation and control systems. The handbook includes information on temperature, pressure, flow, and level detection systems; position indication systems; process control systems; and radiation detection principles. This information will provide personnel with an understanding of the basic operation of various types of DOE nuclear facility instrumentation and control systems

Guidance and Control Software Project Data - Volume 2: Development Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the development documents from the GCS project. Volume 2 contains three appendices: A. Guidance and Control Software Development Specification; B. Design Description for the Pluto Implementation of the Guidance and Control Software; and C. Source Code for the Pluto Implementation of the Guidance and Control Software

LabNotes: A Mobile App for Instrument Control and Data Collection

Data.gov (United States)

National Aeronautics and Space Administration — LabNotes is an IPad/IPod software application (app) and low-cost USB connector harness that can be used to operate and collect data from scientific instruments,...

Fighting Software Piracy: Some Global Conditional Policy Instruments

OpenAIRE

Asongu, Simplice A; Singh, Pritam; Le Roux, Sara

2016-01-01

This study examines the efficiency of tools for fighting software piracy in the conditional distributions of software piracy. Our paper examines software piracy in 99 countries for the period 1994-2010, using contemporary and non-contemporary quantile regressions. The intuition for modelling distributions contingent on existing levels of software piracy is that the effectiveness of tools against piracy may consistently decrease or increase simultaneously with increasing levels of software pir...

Design and manufacture NCS instruments for cement factories

International Nuclear Information System (INIS)

Nguyen Thanh Tuy; Nguyen Tien Dung; Dang Nguyet Anh; Nguyen Phuc; Khuong Thanh Tuan; Luong Duc Long; Pham Trong Quyen

2003-01-01

The ministry project 'Design and manufacture some of NCS instruments for cement factories' is a part of instrumentation for cement production in Vietnam. The objectives of the project include: 1/Design and manufacture the automatic control system for cement raw material mixing, connected to components X-ray analyzer through serial port of PC; 2/Design and manufacture the automatic discharge control system using gamma rays. The instruments, made by the project , for controlling the conveyor belt weighing machine can be easily improved for various types of conveyor belt weighing machines. Their mobility and software equipped can be adapted for requirement of modern cement production technology. The instruments are operating well in some cement factories and they are helping in quality control. (NHA)

Development of intelligent control system for X-ray streak camera in diagnostic instrument manipulator

International Nuclear Information System (INIS)

Pei, Chengquan; Wu, Shengli; Tian, Jinshou; Liu, Zhen; Fang, Yuman; Gao, Guilong; Liang, Lingliang; Wen, Wenlong

2015-01-01

An intelligent control system for an X ray streak camera in a diagnostic instrument manipulator (DIM) is proposed and implemented, which can control time delay, electric focusing, image gain adjustment, switch of sweep voltage, acquiring environment parameters etc. The system consists of 16 A/D converters and 16 D/A converters, a 32-channel general purpose input/output (GPIO) and two sensors. An isolated DC/DC converter with multi-outputs and a single mode fiber were adopted to reduce the interference generated by the common ground among the A/D, D/A and I/O. The software was designed using graphical programming language and can remotely access the corresponding instrument from a website. The entire intelligent control system can acquire the desirable data at a speed of 30 Mb/s and store it for later analysis. The intelligent system was implemented on a streak camera in a DIM and it shows a temporal resolution of 11.25 ps, spatial distortion of less than 10% and dynamic range of 279:1. The intelligent control system has been successfully used in a streak camera to verify the synchronization of multi-channel laser on the Inertial Confinement Fusion Facility

Development of intelligent control system for X-ray streak camera in diagnostic instrument manipulator

Energy Technology Data Exchange (ETDEWEB)

Pei, Chengquan [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi' an Jiaotong University, Xi' an 710049 (China); Wu, Shengli, E-mail: slwu@mail.xjtu.edu.cn [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi' an Jiaotong University, Xi' an 710049 (China); Tian, Jinshou [Xi' an Institute of Optics and Precision Mechanics, Chinese Academy of Sciences, Xi' an 710119 (China); Liu, Zhen [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi' an Jiaotong University, Xi' an 710049 (China); Fang, Yuman [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi' an Jiaotong University, Xi' an 710049 (China); University of the Chinese Academy of Sciences, Beijing 100039 (China); Gao, Guilong; Liang, Lingliang [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi' an Jiaotong University, Xi' an 710049 (China); Xi' an Institute of Optics and Precision Mechanics, Chinese Academy of Sciences, Xi' an 710119 (China); University of the Chinese Academy of Sciences, Beijing 100039 (China); Wen, Wenlong [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi' an Jiaotong University, Xi' an 710049 (China)

2015-11-01

An intelligent control system for an X ray streak camera in a diagnostic instrument manipulator (DIM) is proposed and implemented, which can control time delay, electric focusing, image gain adjustment, switch of sweep voltage, acquiring environment parameters etc. The system consists of 16 A/D converters and 16 D/A converters, a 32-channel general purpose input/output (GPIO) and two sensors. An isolated DC/DC converter with multi-outputs and a single mode fiber were adopted to reduce the interference generated by the common ground among the A/D, D/A and I/O. The software was designed using graphical programming language and can remotely access the corresponding instrument from a website. The entire intelligent control system can acquire the desirable data at a speed of 30 Mb/s and store it for later analysis. The intelligent system was implemented on a streak camera in a DIM and it shows a temporal resolution of 11.25 ps, spatial distortion of less than 10% and dynamic range of 279:1. The intelligent control system has been successfully used in a streak camera to verify the synchronization of multi-channel laser on the Inertial Confinement Fusion Facility.

Klystron control software in the SLC

International Nuclear Information System (INIS)

Jobe, R.K.; Thompson, K.; Phinney, N.

1985-05-01

Triggering, control, and monitoring of 240 high-power klystrons will be supported by the SLC control system this summer. The control software is distributed among a VAX host computer, a local microprocessor cluster, and a dedicated intelligent CAMAC module. The functions performed by these three components and the algorithms used are discussed

Performance and quality control of nuclear medicine instrumentation

International Nuclear Information System (INIS)

Paras, P.

1981-01-01

The status and the recent developments of nuclear medicine instrumentation performance, with an emphasis on gamma-camera performance, are discussed as the basis for quality control. New phantoms and techniques for the measurement of gamma-camera performance parameters are introduced and their usefulness for quality control is discussed. Tests and procedures for dose calibrator quality control are included. Also, the principles of quality control, tests, equipment and procedures for each type of instrument are reviewed, and minimum requirements for an effective quality assurance programme for nuclear medicine instrumentation are suggested. (author)

NIF Projects Controls and Information Systems Software Quality Assurance Plan

Energy Technology Data Exchange (ETDEWEB)

Fishler, B

2011-03-18

Quality achievement for the National Ignition Facility (NIF) and the National Ignition Campaign (NIC) is the responsibility of the NIF Projects line organization as described in the NIF and Photon Science Directorate Quality Assurance Plan (NIF QA Plan). This Software Quality Assurance Plan (SQAP) is subordinate to the NIF QA Plan and establishes quality assurance (QA) activities for the software subsystems within Controls and Information Systems (CIS). This SQAP implements an activity level software quality assurance plan for NIF Projects as required by the LLNL Institutional Software Quality Assurance Program (ISQAP). Planned QA activities help achieve, assess, and maintain appropriate quality of software developed and/or acquired for control systems, shot data systems, laser performance modeling systems, business applications, industrial control and safety systems, and information technology systems. The objective of this SQAP is to ensure that appropriate controls are developed and implemented for management planning, work execution, and quality assessment of the CIS organization's software activities. The CIS line organization places special QA emphasis on rigorous configuration control, change management, testing, and issue tracking to help achieve its quality goals.

NIF Projects Controls and Information Systems Software Quality Assurance Plan

International Nuclear Information System (INIS)

Fishler, B.

2011-01-01

Quality achievement for the National Ignition Facility (NIF) and the National Ignition Campaign (NIC) is the responsibility of the NIF Projects line organization as described in the NIF and Photon Science Directorate Quality Assurance Plan (NIF QA Plan). This Software Quality Assurance Plan (SQAP) is subordinate to the NIF QA Plan and establishes quality assurance (QA) activities for the software subsystems within Controls and Information Systems (CIS). This SQAP implements an activity level software quality assurance plan for NIF Projects as required by the LLNL Institutional Software Quality Assurance Program (ISQAP). Planned QA activities help achieve, assess, and maintain appropriate quality of software developed and/or acquired for control systems, shot data systems, laser performance modeling systems, business applications, industrial control and safety systems, and information technology systems. The objective of this SQAP is to ensure that appropriate controls are developed and implemented for management planning, work execution, and quality assessment of the CIS organization's software activities. The CIS line organization places special QA emphasis on rigorous configuration control, change management, testing, and issue tracking to help achieve its quality goals.

Human factors survey of advanced instrumentation and controls technologies in nuclear plants

International Nuclear Information System (INIS)

Carter, R.J.

1992-01-01

A survey of advanced instrumentation and controls (I ampersand C) technologies and associated human factors issues in the US and Canadian nuclear industries was carried out by a team from Oak Ridge national laboratory to provide background for the development of regulatory policy, criteria, and guides for review of advanced I ampersand C systems as well as human engineering guidelines for evaluating these systems. The survey found those components of the US nuclear industry surveyed to be quite interested in advanced I ampersand C, but very cautious in implementing such systems in nuclear facilities and power plants. The trend in the facilities surveyed is to experiment cautiously when there is an intuitive advantage or short-term payoff. In the control room, the usual practice is direct substitution of digital and microprocessor-based instruments or systems that are functionally identical to the analog instruments or systems being replaced. The most advanced I ampersand C systems were found in the Canadian CANDU plants, where the newest plant has digital system in almost 100% of its control systems and in over 70% of its plant protection system. The hypothesis that properly 'introducing digital systems increases safety' is supported by the Canadian experience. The performance of these digital systems was achieved using an appropriate quality assurance program for the software development. The ability of digital systems to detect impending failures and initiate a fail-safe action, is a significant safety issue that should be of special interest to every US utility as well as to the US Nuclear Regulatory Commission. (orig.)

Techniques and tools for software qualification in KNICS

International Nuclear Information System (INIS)

Cha, Kyung H.; Lee, Yeong J.; Cheon, Se W.; Kim, Jang Y.; Lee, Jang S.; Kwon, Kee C.

2004-01-01

This paper describes techniques and tools for qualifying safety software in Korea Nuclear Instrumentation and Control System (KNICS). Safety software are developed and applied for a Reactor Protection System (RPS), an Engineered Safety Features and Component Control System (ESF-CCS), and a safety Programmable Logic Controller (PLC) in the KNICS. Requirements and design specifications of safety software are written by both natural language and formal specification languages. Statechart is used for formal specification of software of the ESF-CCS and the safety PLC while NuSCR is used for formal specification of them of the RPS. pSET (POSCON Software Engineering Tool) as a software development tool has been developed and utilized for the IEC61131-3 based PLC programming. The qualification of the safety software consists of software verification and validation (V and V) through software life cycle, software safety analysis, and software configuration management, software quality assurance, and COTS (Commercial-Off-The-Shelf) dedication. The criteria and requirements for qualifying the safety software have been established with them in Software Review Plan (SRP)/Branch Technical Positions (BTP)-14, IEEE Std. 7-4.3.2-1998, NUREG/CR-6463, IEEE Std. 1012-1998, and so on. Figure 1 summarizes qualification techniques and tools for the safety software

How To Control Color Appearance With Instrumentation

Science.gov (United States)

Burns, Margaret E.

1980-05-01

Colorimetry, as defined by the International Commission on Illumination, is the measurement of colors, made possible by the properties of the eye and based on a set of conventions. Instrumentation for measuring object color, therefore, must be based on a human observer. The intent is to design an instrument that in effect responds as a person would, so that research development, production control and quality control areas have some means of assessing the acceptability of the appearance of a product. Investigations of a human observer's psychological response to color, and the manner in which visual observations are made, give the instrument designer and manufacturer data necessary to answer two questions: a. How can we put numbers (instrument read-out) on a perception that occurs in the brain of the observer? b. What can we learn from examination of a visual observing situation that will guide us in our design of an instrumental simulation of this situation? Involving as it does our own daily, almost unconscious, practice of making judgments concerning the things we see, the design and manufacture of color measurement instruments is an exceedingly interesting field. The advances being made concurrently today in research concerning human color vision and in optical and electronic technology will make possible increasingly useful instrumentation for quality control of product color.

The COMPASS Tokamak Plasma Control Software Performance

Science.gov (United States)

Valcarcel, Daniel F.; Neto, André; Carvalho, Ivo S.; Carvalho, Bernardo B.; Fernandes, Horácio; Sousa, Jorge; Janky, Filip; Havlicek, Josef; Beno, Radek; Horacek, Jan; Hron, Martin; Panek, Radomir

2011-08-01

The COMPASS tokamak has began operation at the IPP Prague in December 2008. A new control system has been built using an ATCA-based real-time system developed at IST Lisbon. The control software is implemented on top of the MARTe real-time framework attaining control cycles as short as 50 μs, with a jitter of less than 1 μs. The controlled parameters, important for the plasma performance, are the plasma current, position of the plasma current center, boundary shape and horizontal and vertical velocities. These are divided in two control cycles: slow at 500 μs and fast at 50 μs. The project has two phases. First, the software implements a digital controller, similar to the analog one used during the COMPASS-D operation in Culham. In the slow cycle, the plasma current and position are measured and controlled with PID and feedforward controllers, respectively, the shaping magnetic field is preprogrammed. The vertical instability and horizontal equilibrium are controlled with the faster 50-μs cycle PID controllers. The second phase will implement a plasma-shape reconstruction algorithm and controller, aiming at optimized plasma performance. The system was designed to be as modular as possible by breaking the functional requirements of the control system into several independent and specialized modules. This splitting enabled tuning the execution of each system part and to use the modules in a variety of applications with different time constraints. This paper presents the design and overall performance of the COMPASS control software.

Status of the Instrument Control Unit for EPD on-board Solar Orbiter

Science.gov (United States)

Sánchez Prieto, Sebastián; Da Silva, Antonio; Rodriguez Polo, Oscar; Parra Espada, Pablo; Gutierrez Molina, Oscar; Fernandez Salgado, Javier

Solar Orbiter is the next heliospheric mission sponsored by ESA. The launch is planned for 2017 and it will be as close as 0.28 AU from the Sun. One of the instruments for Solar Orbiter is the Energetic Particle Detector (EPD) responsible for measuring energies from 2 keV to 200 MeV/n. EPD consists of four detectors, Electron Proton Telescope (EPT), High Energy Telescope (HET), SupraThermal Electrons, Ions, & Neutrals (STEIN), and Suprathermal Ion Spectrograph (SIS), plus the Instrument Control Unit called ICU. The Space Research Group of the University of Alcalá in Spain is the responsible for developing the ICU. In this work we present the development status of the ICU after the Critical Design Review. We also address the planned activities for the next year including the development of the Engineering and Qualification Model (EQM) and Flight Model (PM). Special focus is paid to the software and verification & validation activities.

Experiment to evaluate software safety

International Nuclear Information System (INIS)

Soubies, B.; Henry, J.Y.

1994-01-01

The process of licensing nuclear power plants for operation consists of mandatory steps featuring detailed examination of the instrumentation and control system by the safety authorities, including softwares. The criticality of these softwares obliges the manufacturer to develop in accordance with the IEC 880 standard 'Computer software in nuclear power plant safety systems' issued by the International Electronic Commission. The evaluation approach, a two-stage assessment is described in detail. In this context, the IPSN (Institute of Protection and Nuclear Safety), the technical support body of the safety authority uses the MALPAS tool to analyse the quality of the programs. (R.P.). 4 refs

Software for an automated processing system for radioisotope information from multichannel radiodiagnostic instruments

International Nuclear Information System (INIS)

Zelenin, P.E.; Meier, V.P.

1985-01-01

The SAORI-01 system for the automated processing of radioisotope information is designed for the collection, processing, and representation of information coming from gamma chambers and multichannel radiodiagnostic instruments (MRI) and is basically oriented toward the radiodiagnostic laboratories of major multidisciplinary hospitals and scientific-research institutes. The functional characteristics of the basic software are discussed, and permits performance of the following functions: collection of information regarding MRI; processing and representation of recorded information; storage of patient files on magnetic carriers; and writing of special processing programs in the FORTRAN and BASIC high-level language

IAEA safeguards instrumentation: Development, implementation and control

International Nuclear Information System (INIS)

Rundquist, D.E.

1983-01-01

Extensive development efforts over the last 5 years have produced a number of new instruments to help the IAEA meet its safeguards obligations. Implementation of these new instruments is proceeding at a necessarily slower pace. To optimize the performance and reliability of the instrumentation systems when used in safeguards applications, increasing attention is needed to be spent on performance monitoring and control of the instruments. (author)

Software V ampersand V methods for digital plant protection system

International Nuclear Information System (INIS)

Kim, Hung-Jun; Han, Jai-Bok; Chun, Chong-Son; Kim, Sung; Kim, Kern-Joong.

1997-01-01

Careful thought must be given to software design in the development of digital based systems that play a critical role in the successful operation of nuclear power plants. To evaluate the software verification and validation methods as well as to verify its system performance capabilities for the upgrade instrumentation and control system in the Korean future nuclear power plants, the prototype Digital Plant, Protection System (DPPS) based on the Programmable Logic Controller (PLC) has been constructed. The system design description and features are briefly presented, and the software design and software verification and validation methods are focused. 6 refs., 2 figs

Technical Training seminar: Texas Instruments

CERN Multimedia

2006-01-01

Monday 6 November TECHNICAL TRAINING SEMINAR 14:00 to 17:30 - Training Centre Auditorium (bldg. 593) Texas Instruments Technical Seminar Michael Scholtholt, Field Application Engineer / TEXAS INSTRUMENTS (US, D, CH) POWER - A short approach to Texas Instruments power products Voltage mode vs. current mode control Differentiating DC/DC converters by analyzing control and compensation schemes: line / load regulation, transient response, BOM, board space, ease-of-use Introduction to the SWIFT software FPGA + CPLD power solutions WIRELESS / CHIPCON Decision criteria when choosing a RF platform Introduction to Texas Instruments wireless products: standardized platforms proprietary platforms ( 2.4 GHz / sub 1 GHz) development tools Antenna design: example for 2.4 GHz questions, discussion Industrial partners: Robert Medioni, François Caloz / Spoerle Electronic, CH-1440 Montagny (VD), Switzerland Phone: +41 24 447 0137, email: RMedioni@spoerle.com, http://www.spoerle.com Language: English. Free s...

Instrument validation system of general application

International Nuclear Information System (INIS)

Filshtein, E.L.

1990-01-01

This paper describes the Instrument Validation System (IVS) as a software system which has the capability of evaluating the performance of a set of functionally related instrument channels to identify failed instruments and to quantify instrument drift. Under funding from Combustion Engineering (C-E), the IVS has been developed to the extent that a computer program exists whose use has been demonstrated. The initial development work shows promise for success and for wide application, not only to power plants, but also to industrial manufacturing and process control. Applications in the aerospace and military sector are also likely

A process control software package for the SRS

International Nuclear Information System (INIS)

Atkins, V.R.; Poole, D.E.; Rawlinson, W.R.

1980-03-01

The development of software to give high level access from application programs for monitoring and control of the Daresbury Synchrotron Radiation Source on a network-wide basis is described. The design and implementation of the control system database, a special supervisor call and and 'executive' type task handling of all process input/output services for the 7/32 (which runs under 05/32-MT), and process control 'device driver' software for the 7/16 (run under L5/16-MT) are included. (UK)

Software configuration management plan, 241-AY and 241-AZ tank farm MICON automation system

International Nuclear Information System (INIS)

Hill, L.F.

1997-01-01

This document establishes a Computer Software Configuration Management Plan (CSCM) for controlling software for the MICON Distributed Control System (DCS) located at the 241-AY and 241-AZ Aging Waste Tank Farm facilities in the 200 East Area. The MICON DCS software controls and monitors the instrumentation and equipment associated with plant systems and processes. A CSCM identifies and defines the configuration items in a system (section 3.1), controls the release and change of these items throughout the system life cycle (section 3.2), records and reports the status of configuration items and change requests (section 3.3), and verifies the completeness and correctness of the items (section 3.4). All software development before initial release, or before software is baselined, is considered developmental. This plan does not apply to developmental software. This plan applies to software that has been baselined and released. The MICON software will monitor and control the related instrumentation and equipment of the 241-AY and 241-AZ Tank Farm ventilation systems. Eventually, this software may also assume the monitoring and control of the tank sludge washing equipment and other systems as they are brought on line. This plan applies to the System Cognizant Manager and MICON Cognizant Engineer (who is also referred to herein as the system administrator) responsible for the software/hardware and administration of the MICON system. This document also applies to any other organizations within Tank Farms which are currently active on the system including system cognizant engineers, nuclear operators, technicians, and control room supervisors

Ground test accelerator control system software

International Nuclear Information System (INIS)

Burczyk, L.; Dalesio, R.; Dingler, R.; Hill, J.; Howell, J.A.; Kerstiens, D.; King, R.; Kozubal, A.; Little, C.; Martz, V.; Rothrock, R.; Sutton, J.

1988-01-01

This paper reports on the GTA control system that provides an environment in which the automation of a state-of-the-art accelerator can be developed. It makes use of commercially available computers, workstations, computer networks, industrial 110 equipment, and software. This system has built-in supervisory control (like most accelerator control systems), tools to support continuous control (like the process control industry), and sequential control for automatic start-up and fault recovery (like few other accelerator control systems). Several software tools support these levels of control: a real-time operating system (VxWorks) with a real-time kernel (VRTX), a configuration database, a sequencer, and a graphics editor. VxWorks supports multitasking, fast context-switching, and preemptive scheduling. VxWorks/VRTX is a network-based development environment specifically designed to work in partnership with the UNIX operating system. A data base provides the interface to the accelerator components. It consists of a run time library and a database configuration and editing tool. A sequencer initiates and controls the operation of all sequence programs (expressed as state programs). A graphics editor gives the user the ability to create color graphic displays showing the state of the machine in either text or graphics form

Software process improvement: controlling developers, managers or users?

DEFF Research Database (Denmark)

Nørbjerg, Jacob

1999-01-01

The paper discusses how the latest trend in the management of software development: software process improvement (SPI) may affect user-developer relations. At the outset, SPI concerns the "internal workings" of software organisations, but it may also be interpreted as one way to give the developer...... organisation more control over the development process and the relations with the user organization....

RTSPM: real-time Linux control software for scanning probe microscopy.

Science.gov (United States)

Chandrasekhar, V; Mehta, M M

2013-01-01

Real time computer control is an essential feature of scanning probe microscopes, which have become important tools for the characterization and investigation of nanometer scale samples. Most commercial (and some open-source) scanning probe data acquisition software uses digital signal processors to handle the real time data processing and control, which adds to the expense and complexity of the control software. We describe here scan control software that uses a single computer and a data acquisition card to acquire scan data. The computer runs an open-source real time Linux kernel, which permits fast acquisition and control while maintaining a responsive graphical user interface. Images from a simulated tuning-fork based microscope as well as a standard topographical sample are also presented, showing some of the capabilities of the software.

Control of training instrument

International Nuclear Information System (INIS)

Seo, K. W.; Joo, Y. C.; Park, J. C.; Hong, C. S.; Choi, I. K.; Cho, B. J.; Lee, H. Y.; Seo, I. S.; Park, N. K.

1996-01-01

This report describes the annual results on control of training instrument. The scope and contents are the following: 1. Control of Compact Nuclear Simulator 2. Control of Radiation/Radioactivity Measurement 3. Control of Non-Destructive Testing Equipment 4. Control of Chemical Equipment 5. Control of Personal Computer 6. Other related Lecture Aid Equipment. Efforts were employed to upgrade the training environment through retrofitting experimental facilities, compiling teaching materials and reforcing audio-visual aids. The Nuclear Training Center executed the open-door training courses for 2,496 engineers/scientists from the nuclear regulatory, nuclear industries, research institutes and other related organizations by means of offering 45 training courses during the fiscal year 1995. (author). 15 tabs., 7 figs., 13 refs

Software development on the DIII-D control and data acquisition computers

International Nuclear Information System (INIS)

Penaflor, B.G.; McHarg, B.B. Jr.; Piglowski, D.

1997-11-01

The various software systems developed for the DIII-D tokamak have played a highly visible and important role in tokamak operations and fusion research. Because of the heavy reliance on in-house developed software encompassing all aspects of operating the tokamak, much attention has been given to the careful design, development and maintenance of these software systems. Software systems responsible for tokamak control and monitoring, neutral beam injection, and data acquisition demand the highest level of reliability during plasma operations. These systems made up of hundreds of programs totaling thousands of lines of code have presented a wide variety of software design and development issues ranging from low level hardware communications, database management, and distributed process control, to man machine interfaces. The focus of this paper will be to describe how software is developed and managed for the DIII-D control and data acquisition computers. It will include an overview and status of software systems implemented for tokamak control, neutral beam control, and data acquisition. The issues and challenges faced developing and managing the large amounts of software in support of the dynamic and everchanging needs of the DIII-D experimental program will be addressed

Virtual Reality Musical Instruments

DEFF Research Database (Denmark)

Serafin, Stefania; Erkut, Cumhur; Kojs, Juraj

2016-01-01

The rapid development and availability of low-cost technologies have created a wide interest in virtual reality. In the field of computer music, the term “virtual musical instruments” has been used for a long time to describe software simulations, extensions of existing musical instruments......, and ways to control them with new interfaces for musical expression. Virtual reality musical instruments (VRMIs) that include a simulated visual component delivered via a head-mounted display or other forms of immersive visualization have not yet received much attention. In this article, we present a field...

Virtualization of Legacy Instrumentation Control Computers for Improved Reliability, Operational Life, and Management.

Science.gov (United States)

Katz, Jonathan E

2017-01-01

Laboratories tend to be amenable environments for long-term reliable operation of scientific measurement equipment. Indeed, it is not uncommon to find equipment 5, 10, or even 20+ years old still being routinely used in labs. Unfortunately, the Achilles heel for many of these devices is the control/data acquisition computer. Often these computers run older operating systems (e.g., Windows XP) and, while they might only use standard network, USB or serial ports, they require proprietary software to be installed. Even if the original installation disks can be found, it is a burdensome process to reinstall and is fraught with "gotchas" that can derail the process-lost license keys, incompatible hardware, forgotten configuration settings, etc. If you have running legacy instrumentation, the computer is the ticking time bomb waiting to put a halt to your operation.In this chapter, I describe how to virtualize your currently running control computer. This virtualized computer "image" is easy to maintain, easy to back up and easy to redeploy. I have used this multiple times in my own lab to greatly improve the robustness of my legacy devices.After completing the steps in this chapter, you will have your original control computer as well as a virtual instance of that computer with all the software installed ready to control your hardware should your original computer ever be decommissioned.

Concluding from operating experience to instrumentation and control systems

International Nuclear Information System (INIS)

Pleger, H.; Heinsohn, H.

1997-01-01

Where conclusions are drawn from operating experience to instrumentation and control systems, two general statements should be made. First: There have been braekdowns, there have also been deficiencies, but in principle operating experience with the instrumentation and control systems of German nuclear power plants has been good. With respect to the debates about the use of modern digital instrumentation and control systems it is safe to say, secondly, that the instrumentation and control systems currently in use are working reliably. Hence, there is no need at present to replace existing systems for reasons of technical safety. However, that time will come. It is a good thing, therefore, that the use of modern digital instrumentation and control systems is to begin in the field of limiting devices. The operating experience which will thus be accumulated will benefit digital instrumentation and control systems in their qualification process for more demanding applications. This makes proper logging of operating experience an important function, even if it cannot be transferred in every respect. All parties involved therefore should see to it that this operating experience is collected in accordance with criteria agreed upon so as to prevent unwanted surprises later on. (orig.) [de

Advances in and uses of gamma-ray field instrumentation at Los Alamos

International Nuclear Information System (INIS)

Halbig, J.K.; Klosterbuer, S.F.; Russo, P.A.; Sprinkle, J.K. Jr.; Smith, S.E.; Ianakiev, K.

1994-01-01

We are developing a set of tools to be used by the Safeguards Assay Group to solve problems found in safeguards and the domestic nuclear industry. The tools are also applicable to problems dealing with the environment, defense, and other areas of national and international interest. We have used extensively the advances in hardware and software since our last multichannel analyzer (MCA) development activities over a decade ago. We are also using our experience with and feedback from users of our previous instruments. In analyzing the instrument needs of our constituents and the characteristics of our previous instruments, which we think have inhibited their broader use, we have concluded that uses for an MCA-type instrument are widely varied and fundamentally changing,and that any new instruments should include a versatile, widely used hardware interface, which is as independent as possible of hardware standards, and which is readily interfaced to the computers or controllers rapidly evolving in the commercial sector. In addition, software tools must be provided that allow Los Alamos, users, and third parties to quickly and conveniently develop software specific to the user or the measurement to control the basic instrument we develop. This paper deals mainly with a miniature and modular multi-channel analyzer (M 3 CA) and its applications

The Challenges of the "Software Support for Industrial Controls" Contract

CERN Document Server

Ninin, P

2000-01-01

ST division is currently specifying a 'Software Support for Industrial Controls' contract. The application of this contract and its success will require several changes in our habits for specifying, designing, and maintaining control systems. This paper summarizes some key concepts which should be respected in order to obtain maximum benefits from the future contract and to optimize the software activities in the division. The contract concerns the maintenance and development of the monitoring and control systems used for supervising CERN's technical infrastructure (electrical distribution, cooling water, air conditioning, safety, and access control). The systems concerned consist of computer and communication hardware and software, tailored to provide specific functionalities for the remote operation, command, and monitoring of equipment. All these systems use commercially available software and hardware such as SCADA, PLCs and associated drivers, controllers, fieldbuses, and networks. It is intended to cont...

Conceptual design for controller software of mechatronic systems

NARCIS (Netherlands)

Broenink, Johannes F.; Hilderink, G.H.; Bakkers, André; Bradshaw, Alan; Counsell, John

1998-01-01

The method and software tool presented here, aims at supporting the development of control software for mechatronic systems. Heterogeneous distributed embedded processors are considered as target hardware. Principles of the method are that the implementation process is a stepwise refinement from

Integrated software environment dedicated for implementation of control systems based on PLC controllers

Directory of Open Access Journals (Sweden)

Szymon SURMA

2007-01-01

Full Text Available Industrial processes’ control systems based on PLC controllers play today a very important role in all fields of transport, including also sea transport. Construction of control systems is the field of engineering, which has been continuously evolving towards maximum simplification of system design path. Up to now the time needed forthe system construction from the design to commissioning had to be divided into a few stages. A mistake made in an earlier stage caused that in most cases the next stages had to be restarted. Available debugging systems allows defect detection at an early stage of theproject implementation. The paper presents general characteristic of integrated software for implementation of complex control systems. The issues related to the software use for programming of the visualisation environment, control computer, selection oftransmission medium and transmission protocol as well as PLC controllers’ configuration, software and control have been analysed.

Development of a new control software package for Pakistan Research Reactor-2

International Nuclear Information System (INIS)

Qazi, M.K.

1993-05-01

The development of a new control software package for Pakistan Research Reactor-2 is presented. The software operates in different modes which comprises of surveillance, pre-operational self tests, operator, supervisor and robotic control. The control logic critically damp the system minimizing power overshoots. The software, handles multiple abnormal conditions, provides an elaborate access control and maintains startup/shutdown record. The report describes the functional details and covers the operational aspects of the new control software. (author)

Development of tools for safety analysis of control software in advanced reactors

International Nuclear Information System (INIS)

Guarro, S.; Yau, M.; Motamed, M.

1996-04-01

Software based control systems have gained a pervasive presence in a wide variety of applications, including nuclear power plant control and protection systems which are within the oversight and licensing responsibility of the US Nuclear Regulatory Commission. While the cost effectiveness and flexibility of software based plant process control is widely recognized, it is very difficult to achieve and prove high levels of demonstrated dependability and safety assurance for the functions performed by process control software, due to the very flexibility and potential complexity of the software itself. The development of tools to model, analyze and test software design and implementations in the context of the system that the software is designed to control can greatly assist the task of providing higher levels of assurance than those obtainable by software testing alone. This report presents and discusses the development of the Dynamic Flowgraph Methodology (DFM) and its application in the dependability and assurance analysis of software-based control systems. The features of the methodology and full-scale examples of application to both generic process and nuclear power plant control systems are presented and discussed in detail. The features of a workstation software tool developed to assist users in the application of DFM are also described

Development of tools for safety analysis of control software in advanced reactors

Energy Technology Data Exchange (ETDEWEB)

Guarro, S.; Yau, M.; Motamed, M. [Advanced Systems Concepts Associates, El Segundo, CA (United States)

1996-04-01

Software based control systems have gained a pervasive presence in a wide variety of applications, including nuclear power plant control and protection systems which are within the oversight and licensing responsibility of the US Nuclear Regulatory Commission. While the cost effectiveness and flexibility of software based plant process control is widely recognized, it is very difficult to achieve and prove high levels of demonstrated dependability and safety assurance for the functions performed by process control software, due to the very flexibility and potential complexity of the software itself. The development of tools to model, analyze and test software design and implementations in the context of the system that the software is designed to control can greatly assist the task of providing higher levels of assurance than those obtainable by software testing alone. This report presents and discusses the development of the Dynamic Flowgraph Methodology (DFM) and its application in the dependability and assurance analysis of software-based control systems. The features of the methodology and full-scale examples of application to both generic process and nuclear power plant control systems are presented and discussed in detail. The features of a workstation software tool developed to assist users in the application of DFM are also described.

The development of digital oscilloscope control software in nuclear measurement

International Nuclear Information System (INIS)

Pu Minghui; Tian Geng; Li Xianyou

2004-01-01

This essay presents the development of an all-purpose digital oscilloscope control software on Windows 95/98 OS. The background and method are discussed in detail, together with the function and characteristics of the software. With the use of this software, a single PC can control several digital oscilloscopes. Solution of main problems encountered in the development is also discussed. (authors)

Electrical Bioimpedance-Controlled Surgical Instrumentation.

Science.gov (United States)

Brendle, Christian; Rein, Benjamin; Niesche, Annegret; Korff, Alexander; Radermacher, Klaus; Misgeld, Berno; Leonhardt, Steffen

2015-10-01

A bioimpedance-controlled concept for bone cement milling during revision total hip replacement is presented. Normally, the surgeon manually removes bone cement using a hammer and chisel. However, this procedure is relatively rough and unintended harm may occur to tissue at any time. The proposed bioimpedance-controlled surgical instrumentation improves this process because, for example, most risks associated with bone cement removal are avoided. The electrical bioimpedance measurements enable online process-control by using the milling head as both a cutting tool and measurement electrode at the same time. Furthermore, a novel integrated surgical milling tool is introduced, which allows acquisition of electrical bioimpedance data for online control; these data are used as a process variable. Process identification is based on finite element method simulation and on experimental studies with a rapid control prototyping system. The control loop design includes the identified process model, the characterization of noise as being normally distributed and the filtering, which is necessary for sufficient accuracy ( ±0.5 mm). Also, in a comparative study, noise suppression is investigated in silico with a moving average filter and a Kalman filter. Finally, performance analysis shows that the bioimpedance-controlled surgical instrumentation may also performs effectively at a higher feed rate (e.g., 5 mm/s).

Research and realization of signal simulation on virtual instrument

Science.gov (United States)

Zhao, Qi; He, Wenting; Guan, Xiumei

2010-02-01

In the engineering project, arbitrary waveform generator controlled by software interface is needed by simulation and test. This article discussed the program using the SCPI (Standard Commands For Programmable Instruments) protocol and the VISA (Virtual Instrument System Architecture) library to control the Agilent signal generator (Agilent N5182A) by instrument communication over the LAN interface. The program can conduct several signal generations such as CW (continuous wave), AM (amplitude modulation), FM (frequency modulation), ΦM (phase modulation), Sweep. As the result, the program system has good operability and portability.

Software for simulation of a computed tomography imaging spectrometer using optical design software

Science.gov (United States)

Spuhler, Peter T.; Willer, Mark R.; Volin, Curtis E.; Descour, Michael R.; Dereniak, Eustace L.

2000-11-01

Our Imaging Spectrometer Simulation Software known under the name Eikon should improve and speed up the design of a Computed Tomography Imaging Spectrometer (CTIS). Eikon uses existing raytracing software to simulate a virtual instrument. Eikon enables designers to virtually run through the design, calibration and data acquisition, saving significant cost and time when designing an instrument. We anticipate that Eikon simulations will improve future designs of CTIS by allowing engineers to explore more instrument options.

Verification and validation of software

International Nuclear Information System (INIS)

Machiels, A.J.; Bhjatt, S.; May, R.S.; Woolley, J.A.

1995-01-01

Several U.S. nuclear utilities have embarked upon extensive programs to replace and upgrade their analog instrumentation and control (I ampersand C) systems with digital technology. These new digital systems cover a wide range of applications, from safety-critical protection systems to nonsafety control systems, and their implementations range from customized, turnkey computer systems to utility-integrated configurations of programmable logic controllers. In all cases, the utility must address the issue of quality of the digital system and its software

Software factory techniques applied to process control at CERN

CERN Document Server

Dutour, Mathias D

2008-01-01

The CERN Large Hadron Collider (LHC) requires constant monitoring and control of quantities of parameters to guarantee operational conditions. For this purpose, a methodology called UNICOS (UNIfied Industrial COntrols Systems) has been implemented to standardize the design of process control applications. To further accelerate the development of these applications, we migrated our existing UNICOS tooling suite toward a software factory in charge of assembling project, domain and technical information seamlessly into deployable PLC (Programmable logic Controller) - SCADA (Supervisory Control And Data Acquisition) systems. This software factory delivers consistently high quality by reducing human error and repetitive tasks, and adapts to user specifications in a cost-efficient way. Hence, this production tool is designed to encapsulate and hide the PLC and SCADA target platforms, enabling the experts to focus on the business model rather than specific syntaxes and grammars. Based on industry standard software, ...

Development of the SONIX software for the YuMO instrument at the IBR-2 reactor

International Nuclear Information System (INIS)

Kirilov, A.S.; Litvinenko, E.I.; Astakhova, N.V.; Murashevich, S.M.; Petukhova, T.B.; Yudin, V.E.; Gordelij, V.I.; Islamov, A.Kh.; Kuklin, A.I.

2003-01-01

The main results of the modernization of the software complex of the YuMO spectrometer are described. The comparison of the previous MS-DOS based software and new OS-9 based one is carried out. The advantages and disadvantages of each program are described. The main features of the new software complex and the results of its long-term operation are presented. It is shown that the software upgrade essentially improved the spectrometer control. (author)

Proceedings of symposium on intelligent nuclear instrumentation-2001

International Nuclear Information System (INIS)

Kataria, S.K.; Vaidya, P.P.; Das, Debashis; Narurkar, P.V.

2001-02-01

Advances in the field of instrumentation are relevant to many areas of importance such as nuclear and accelerator based research, reactor monitoring and control, non-destructive testing and evaluation, laser programme and health and environment monitoring etc. The nuclear instrumentation is a specialized field with very specific expertise in detection, processing and its analysis. The symposium covers various fields of nuclear interest such as radiation detectors, application of ASICs and FPGA in instruments, field instruments, nuclear instrumentation for basic research, accelerator, reactor, health and environmental monitoring instrumentation, medical instrumentation, instrument net working inclusive of field buses, WEB based and wireless technologies, software tools, AI technique in instrumentation etc., in this specialized area. Papers relevant to INIS are indexed separately

Recent development of nuclear power in Japan and instrumentation and control system and control room equipment for advanced light water reactors

International Nuclear Information System (INIS)

Wakayama, N.

1992-01-01

This paper was provided for the 13th IAEA/IWG-NPPCI Meeting and aims to introduce an outline of recent development of nuclear power in Japan and some topics in the field of nuclear power plant control and instrumentation. Forty units of nuclear power plants are in operation in Japan and five units of BWRs and six PWRs are under construction. Construction of prototype FBR Monju have almost completed an construction of High-Temperature Engineering Test Reactor, HTTR, started in March 1991. In parallel of those, extensive effort has been carried out to develop the third generation LWRs which are called Advanced BWR (ABWR) and Advanced PWR (APWR). Two Advanced BWRs are under safety review for construction. Instrumentation and control system of these Advanced LWRs adopts integrated digital I and C system, optical multiplexing signal transmission, fault tolerant control systems and software logic for reactor protection and safety systems and enhances plant control performance and provides human-friendly operation and maintenance environments. Main control room of these Advanced LWRs, comprised with large display panels and advanced console, has special futures such as one-man sit-down operation, human friendly man-machine interface, high level automation in operation and maintenance. (author). 7 refs, 9 figs, 1 tab

Design and Testing of a Controller for the Martian Atmosphere Pressure and Humidity Instrument DREAMS-P/H

Science.gov (United States)

Tapani Nikkanen, Timo; Schmidt, Walter; Genzer, Maria; Harri, Ari-Matti; Haukka, Harri

2013-04-01

software is entirely interrupt driven, thus the MCU goes into a power saving standby mode whenever possible. Any measurement or other operation can be stopped by simply interrupting the controller with a telecommand. Software and functional tests of the DREAMS-P/H controller are needed to verify the performance of the instrument in nominal conditions and the correct operation and error detection in anomalous conditions. The nominal conditions tests range from simple functional and performance tests, to longer simulations of continued operation and measurements. Continued operation simulations can be implemented by executing accelerated runs of the expected normal measurement cycles. On the contrary, anomalous conditions tests are used to verify that the controller can handle bad telecommands or anomalous operation of the instrument transducers, for example in the case of malfunctioning sensors. Bad telecommand tests are done by feeding illegal parameters or scrambled telecommands to the controller. Malfunctioning sensors can be simulated by modifying the signals coming from the sensors and reference channels. All expected use cases and all imagined unexpected operating circumstances are studied to ensure that the system is robust. This also makes the planned modification of the design for other future missions easier and safer. Reference: [1] ESA ExoMars EDM mission: http://exploration.esa.int/science-e/www/object/index.cfm?fobjectid=47852 [2] FMI Space Projects website: http://space.fmi.fi/index.php?id=23

Multipotenciostat System Based on Virtual Instrumentation

Directory of Open Access Journals (Sweden)

Arrieta-Almario Álvaro Angel

2014-07-01

Full Text Available To carry out this project an electronic multichannel system of electrochemical measurement or multipotenciostat was developed. It is based on the cyclic voltammetry measurement technique, controlled by a computer that monitors, by means of an electronic circuit, both the voltage generated from the Pc and supplied to an electrolytic cell, and the current that flows through the electrodes of it. To design the application software and the user interface, Virtual Instrumentation was used. On the other hand, to perform the communication between the multipotenciostat circuit and the designed software, the National Instruments NI9263 and NI9203 acquisition modules were used. The system was tested on a substance with a known REDOX property, as well as to discriminate and classify some samples of coffee.

An Investigation of Secure Remote Instrument Control

Energy Technology Data Exchange (ETDEWEB)

Schissel, D.; Abla, G.; Penaflor, B. [General Atomics, San Diego (United States); Ciarlette, D. [Oak Ridge National Laboratory, Oak Ridge (United States)

2009-07-01

This paper examines the computer science issues associated with secure remote instrumentation control for magnetic fusion experiments. Computer science research into enhancing the ability to scientifically participate in a fusion experiment remotely has been growing in size in an attempt to better address the needs of fusion scientists worldwide. The natural progression of this research is to examine how to move from remote scientific participation to remote hardware control. The vision is to define a gatekeeper software system that will be the only channel of interaction for incoming requests to the experimental site. The role of the gatekeeper is to validate the identification and access privilege of the requester and to insure the validity of the proposed request. The vision for the gatekeeper is that it be a modular system that is simple in design and defined in a way that makes its implementation and operation transparent and obvious. The architecture of the module interface is flexible enough that it can easily allow the future addition of new modules. At the same time, it should be transparent to end-users and allow a high volume of activity so as to not provide a work bottleneck. Appropriate security requires the ability to verify identity (authentication), verify access control (authorization), and validate the appropriateness of requests. The validation process can include provenance and semantic methodologies. The results of the gatekeeper design and initial prototype testing will be presented as well as a discussion on the implication of this research on the operation of fusion experimental machines such as ITER. (authors)

Software factory techniques applied to Process Control at CERN

CERN Multimedia

Dutour, MD

2007-01-01

The CERN Large Hadron Collider (LHC) requires constant monitoring and control of quantities of parameters to guarantee operational conditions. For this purpose, a methodology called UNICOS (UNIfied Industrial COntrols Systems) has been implemented to standardize the design of process control applications. To further accelerate the development of these applications, we migrated our existing UNICOS tooling suite toward a software factory in charge of assembling project, domain and technical information seamlessly into deployable PLC (Programmable logic Controller) – SCADA (Supervisory Control And Data Acquisition) systems. This software factory delivers consistently high quality by reducing human error and repetitive tasks, and adapts to user specifications in a cost-efficient way. Hence, this production tool is designed to encapsulate and hide the PLC and SCADA target platforms, enabling the experts to focus on the business model rather than specific syntaxes and grammars. Based on industry standard software...

Using Cognitive Control in Software Defined Networking for Port Scan Detection

Science.gov (United States)

2017-07-01

ARL-TR-8059 ● July 2017 US Army Research Laboratory Using Cognitive Control in Software -Defined Networking for Port Scan...Cognitive Control in Software -Defined Networking for Port Scan Detection by Vinod K Mishra Computational and Information Sciences Directorate, ARL...Technical Report 3. DATES COVERED (From - To) 15 June–31 July 2016 4. TITLE AND SUBTITLE Using Cognitive Control in Software -Defined Networking for

Towards a controlled vocabulary on software engineering education

Science.gov (United States)

Pizard, Sebastián; Vallespir, Diego

2017-11-01

Software engineering is the discipline that develops all the aspects of the production of software. Although there are guidelines about what topics to include in a software engineering curricula, it is usually unclear which are the best methods to teach them. In any science discipline the construction of a classification schema is a common approach to understand a thematic area. This study examines previous publications in software engineering education to obtain a first controlled vocabulary (a more formal definition of a classification schema) in the field. Publications from 1988 to 2014 were collected and processed using automatic clustering techniques and the outcomes were analysed manually. The result is an initial controlled vocabulary with a taxonomy form with 43 concepts that were identified as the most used in the research publications. We present the classification of the concepts in three facets: 'what to teach', 'how to teach' and 'where to teach' and the evolution of concepts over time.

Instrumentation and control for fossil-energy processes

Energy Technology Data Exchange (ETDEWEB)

1982-09-01

The 1982 symposium on instrumentation and control for fossil energy processes was held June 7 through 9, 1982, at Adam's Mark Hotel, Houston, Texas. It was sponsored by the US Department of Energy, Office of Fossil Energy; Argonne National Laboratory; and the Society for Control and Instrumentation of Energy Processes. Fifty-two papers have been entered individually into EDB and ERA; eleven papers had been entered previously from other sources. (LTN)

Increasing software testability with standard access and control interfaces

Science.gov (United States)

Nikora, Allen P; Some, Raphael R.; Tamir, Yuval

2003-01-01

We describe an approach to improving the testability of complex software systems with software constructs modeled after the hardware JTAG bus, used to provide visibility and controlability in testing digital circuits.

Control software for the CBM readout chain

Energy Technology Data Exchange (ETDEWEB)

Loizeau, Pierre-Alain [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH (Germany)

2016-07-01

The Compressed Baryonic Matter (CBM) experiment, which will be built at FAIR, will use free-streaming readout electronics to acquire high-statistics data-sets of physics probes in fixed target heavy-ion collisions. Since no simple signatures suitable for a hardware trigger are available for most of them, reconstruction and selection of the interesting collisions will be done in software, in a computer farm called First Level Event Selector (FLES). The raw data coming from the detectors is pre-processed, pre-calibrated and aggregated in a FPGA based layer called Data Preprocessing Boards (DPB). IPbus will be used to communicate with the DPBs and through them with the elements of the readout chain closer to detectors. A slow control environment based on this software is developed by CBM to configure in an efficient way the DPBs as well as the Front-End Electronics and monitor their performances. This contribution presents the layout planned for the slow control software, its first implementation and corresponding test results.

Quality control of software in dissimilar systems using a common clinical data base

International Nuclear Information System (INIS)

Erickson, J.J.; Price, R.R.; Touya, J.J.; Kronenberg, M.W.; Pederson, R.; Rollo, F.D.

1980-01-01

For a long time there has been widespread interest in the quality control of diagnostic instrumentation. The increasing dependence on computational systems for clinical results makes it imperative that methods for quality control of diagnostic software be developed. This paper proposes a method based on the use of a collection of patient studies for which the results have been corroborated by independent methods. The data set will be distributed in a format requiring no special handling by the system being tested and will appear identical to studies actually collected by the host system. An example of the use of a preliminary version of the data set for comparison of two systems is shown. The comparison shows that analyses performed on the two systems agree very well and can be reliably compared for follow-up studies of a patient

Software qualification in safety applications

International Nuclear Information System (INIS)

Lawrence, J.D.

2000-01-01

The developers of safety-critical instrumentation and control systems must qualify the design of the components used, including the software in the embedded computer systems, in order to ensure that the component can be trusted to perform its safety function under the full range of operating conditions. There are well known ways to qualify analog systems using the facts that: (1) they are built from standard modules with known properties; (2) design documents are available and described in a well understood language; (3) the performance of the component is constrained by physics; and (4) physics models exist to predict the performance. These properties are not generally available for qualifying software, and one must fall back on extensive testing and qualification of the design process. Neither of these is completely satisfactory. The research reported here is exploring an alternative approach that is intended to permit qualification for an important subset of instrumentation software. The research goal is to determine if a combination of static analysis and limited testing can be used to qualify a class of simple, but practical, computer-based instrumentation components for safety application. These components are of roughly the complexity of a motion detector alarm controller. This goal is accomplished by identifying design constraints that enable meaningful analysis and testing. Once such design constraints are identified, digital systems can be designed to allow for analysis and testing, or existing systems may be tested for conformance to the design constraints as a first step in a qualification process. This will considerably reduce the cost and monetary risk involved in qualifying commercial components for safety-critical service

Saltwell PIC Skid Programmable Logic Controller (PLC) Software Configuration Management Plan

International Nuclear Information System (INIS)

KOCH, M.R.

1999-01-01

This document provides the procedures and guidelines necessary for computer software configuration management activities during the operation and maintenance phases of the Saltwell PIC Skids as required by LMH-PRO-309/Rev. 0, Computer Software Quality Assurance, Section 2.6, Software Configuration Management. The software configuration management plan (SCMP) integrates technical and administrative controls to establish and maintain technical consistency among requirements, physical configuration, and documentation for the Saltwell PIC Skid Programmable Logic Controller (PLC) software during the Hanford application, operations and maintenance. This SCMP establishes the Saltwell PIC Skid PLC Software Baseline, status changes to that baseline, and ensures that software meets design and operational requirements and is tested in accordance with their design basis

A low cost modular control and instrumentation system for accelerators

International Nuclear Information System (INIS)

Shubaly, M.R.; Plato, J.G.; Davis, R.W.

1984-01-01

A modular control and instrumentation system, being developed for the RFQ1 accelerator and for ion beam test facilities, is based on an intelligent crate and interchangeable plug-in modules for specific applications. The 8085-based microcomputer used in the system can access up to 256 K of memory, has up to 64 levels of vectored interrupts and time of day, and supports terminals, printers, floppy discs and digital cassette drives. This computer is linked to a bus in the front of the crate which carries not only the usual address, data, and control signals, but also interrupt lines and interrupt chip control lines. This bus is designed for easy interfacing. Plug-in modules connect to the bus, and to monitored equipment via a separate connector leading to a terminal strip on the rear of the crate. These modules monitor absolute and differential temperature, flow-rate, voltages and currents and switch settings. A permanently installed module provides ac power switching, an RS232 serial link and full duplex fibre optic serial links for connection to a central computer. Software for the crate provides for task scheduling, data storage and limit tests, communication to higher levels of the control system and field configuration of the crate. (orig.)

CHECWORKS integrated software for corrosion control

International Nuclear Information System (INIS)

Schefski, C.; Pietralik; Hazelton, T.

1997-01-01

CHECWORKS, a comprehensive software package for managing Flow-Accelerated Corrosion (FAC, also called erosion-corrosion and flow-assisted corrosion) concerns, is expanding to include other systems and other aspects of corrosion control in CANDU reactors. This paper will outline CHECWORKS applications at various CANDU stations and further plans for CHECWORKS to become a code for comprehensive corrosion control management. (author)

LabVIEW: a software system for data acquisition, data analysis, and instrument control.

Science.gov (United States)

Kalkman, C J

1995-01-01

Computer-based data acquisition systems play an important role in clinical monitoring and in the development of new monitoring tools. LabVIEW (National Instruments, Austin, TX) is a data acquisition and programming environment that allows flexible acquisition and processing of analog and digital data. The main feature that distinguishes LabVIEW from other data acquisition programs is its highly modular graphical programming language, "G," and a large library of mathematical and statistical functions. The advantage of graphical programming is that the code is flexible, reusable, and self-documenting. Subroutines can be saved in a library and reused without modification in other programs. This dramatically reduces development time and enables researchers to develop or modify their own programs. LabVIEW uses a large amount of processing power and computer memory, thus requiring a powerful computer. A large-screen monitor is desirable when developing larger applications. LabVIEW is excellently suited for testing new monitoring paradigms, analysis algorithms, or user interfaces. The typical LabVIEW user is the researcher who wants to develop a new monitoring technique, a set of new (derived) variables by integrating signals from several existing patient monitors, closed-loop control of a physiological variable, or a physiological simulator.

Software Quality Control at Belle II

Science.gov (United States)

Ritter, M.; Kuhr, T.; Hauth, T.; Gebard, T.; Kristof, M.; Pulvermacher, C.; Belle Software Group, II

2017-10-01

Over the last seven years the software stack of the next generation B factory experiment Belle II has grown to over one million lines of C++ and Python code, counting only the part included in offline software releases. There are several thousand commits to the central repository by about 100 individual developers per year. To keep a coherent software stack of high quality that it can be sustained and used efficiently for data acquisition, simulation, reconstruction, and analysis over the lifetime of the Belle II experiment is a challenge. A set of tools is employed to monitor the quality of the software and provide fast feedback to the developers. They are integrated in a machinery that is controlled by a buildbot master and automates the quality checks. The tools include different compilers, cppcheck, the clang static analyzer, valgrind memcheck, doxygen, a geometry overlap checker, a check for missing or extra library links, unit tests, steering file level tests, a sophisticated high-level validation suite, and an issue tracker. The technological development infrastructure is complemented by organizational means to coordinate the development.

Quality control of the software in the JT-60 computer control system

International Nuclear Information System (INIS)

Isaji, Nobuaki; Kurihara, Kenichi; Kimura, Toyoaki

1990-07-01

The JT-60 Control System should be improved corresponding to the experimental requirements. In order to keep the integrity of the system even in the modification the concept of quality control (QC) was introduced in the software development. What we have done for QC activity are (1) to establish standard procedures of the software development, (2) to develop support tools for grasping the present status of the program structure, and (3) to develop a document system, and a source program management system. This paper reports these QC activities and their problems for the JT-60 control system. (author)

Designing flexible, ''chemist-friendly'' software to control a radiochemistry autosynthesizer

International Nuclear Information System (INIS)

Feliu, A.L.

1989-01-01

To enhance the utility of process control software to control radiochemistry autosynthesizers used with short-lived positron-emitting isotopes, a scheme is proposed by which routine executive-level tasks, hardware control operations, and chemical procedures have been segregated. This strategy can lead to chemist-friendly control programs for any desired hardware configuration, as illustrated in new software designed to exploit the features and flexibility of the CTI/Siemens Chemical Process Control Unit. (author)

MathWorks Simulink and C++ integration with the new VLT PLC-based standard development platform for instrument control systems

Science.gov (United States)

Kiekebusch, Mario J.; Di Lieto, Nicola; Sandrock, Stefan; Popovic, Dan; Chiozzi, Gianluca

2014-07-01

ESO is in the process of implementing a new development platform, based on PLCs, for upcoming VLT control systems (new instruments and refurbishing of existing systems to manage obsolescence issues). In this context, we have evaluated the integration and reuse of existing C++ libraries and Simulink models into the real-time environment of BECKHOFF Embedded PCs using the capabilities of the latest version of TwinCAT software and MathWorks Embedded Coder. While doing so the aim was to minimize the impact of the new platform by adopting fully tested solutions implemented in C++. This allows us to reuse the in house expertise, as well as extending the normal capabilities of the traditional PLC programming environments. We present the progress of this work and its application in two concrete cases: 1) field rotation compensation for instrument tracking devices like derotators, 2) the ESO standard axis controller (ESTAC), a generic model-based controller implemented in Simulink and used for the control of telescope main axes.

Instrumentation for tomograph positioning

International Nuclear Information System (INIS)

Frenkel, A.D.B.; Castello Branco, L.M.; Reznik, D.S.; Santos, C.A.C.; Borges, J.C.

1986-01-01

The COPPE's Nuclear Instrumentation Lab. has been developing researches directed towards the implementation of a Computer-Based Tomography System. Basically, the system reported in this paper can be divided into three major parts: the mechanical part, responsible for the physical movement (Stepper-Motors, table, etc.); the electronic part, which controls the mechanical part and handles the data-acquisition process (microcomputer, interfaces, etc.); and finally, the support of a software-oriented system, including control programs and information processing routines. (Author) [pt

Single-crystal diffraction instrument TriCS at SINQ

Science.gov (United States)

Schefer, J.; Könnecke, M.; Murasik, A.; Czopnik, A.; Strässle, Th; Keller, P.; Schlumpf, N.

2000-03-01

The single-crystal diffractometer TriCS at the Swiss Continuous Spallation Source (SINQ) is presently in the commissioning phase. A two-dimensional wire detector produced by EMBL was delivered in March 1999. The instrument is presently tested with a single detector. First measurements on magnetic structures have been performed. The instrument is remotely controlled using JAVA-based software and a UNIX DEC-α host computer.

BASTILLE - Better Analysis Software to Treat ILL Experiments - a unified, unifying approach to data reduction and analysis

International Nuclear Information System (INIS)

Johnson, M.

2011-01-01

Data reduction and analysis is a key component in the production of scientific results. If this component, like any other in the chain, is weak, the final output is compromised. The current situation for data reduction and analysis may be regarded as adequate, but it is variable, depending on the instrument, and should be improved. In particular the delivery of new and upgraded instruments in Millennium Phase I and those proposed for Phase II will bring new demands and challenges for software development. Failure to meet these challenges will hamper the exploitation of higher data rates and the delivery of new science. The proposed project is to provide a single, underpinning software infrastructure for data analysis, which would ensure: 1) a clear vision of software provision at ILL; 2) a clear role for the 'Computing for Science' Group (CS) in maintaining and developing the infrastructure and the codes; 3) a well-defined framework for recruiting and training CS staff; 4) ease and efficiency of development within a common, well-defined software environment; 5) safeguarding of key, existing software; and 6) ease of communication with other software like instrument control software to allow real-time data analysis and experiment control, or software from other institutes or sources

EPROM-based LSI-11 for distributed instrumentation control

International Nuclear Information System (INIS)

Hunt, D.N.

1981-01-01

The LLNL Nuclear Chemistry Counting Facility (NCCF) is being converted to a modern production facility. A computer network has been designed and built to implement this conversion. The outermost node of the computer network is a dedicated EPROM-based controller. The controller handles the details of driving the attached nuclear instrumentation, providing a standard interface to the remainder of the network. This paper addresses the design and the implementation of the dedicated instrumentation controller

Verification and validation of control system software

International Nuclear Information System (INIS)

Munro, J.K. Jr.; Kisner, R.A.; Bhadtt, S.C.

1991-01-01

The following guidelines are proposed for verification and validation (V ampersand V) of nuclear power plant control system software: (a) use risk management to decide what and how much V ampersand V is needed; (b) classify each software application using a scheme that reflects what type and how much V ampersand V is needed; (c) maintain a set of reference documents with current information about each application; (d) use Program Inspection as the initial basic verification method; and (e) establish a deficiencies log for each software application. The following additional practices are strongly recommended: (a) use a computer-based configuration management system to track all aspects of development and maintenance; (b) establish reference baselines of the software, associated reference documents, and development tools at regular intervals during development; (c) use object-oriented design and programming to promote greater software reliability and reuse; (d) provide a copy of the software development environment as part of the package of deliverables; and (e) initiate an effort to use formal methods for preparation of Technical Specifications. The paper provides background information and reasons for the guidelines and recommendations. 3 figs., 3 tabs

An investigation of secure remote instrument control

International Nuclear Information System (INIS)

Schissel, D.P.; Abla, G.; Fredian, T.; Greenwald, M.; Penaflor, B.G.; Stillerman, J.; Walker, M.L.; Ciarlette, D.J.

2010-01-01

This paper examines the computer science issues associated with secure remote instrumentation control for magnetic fusion experiments. Computer science research into enhancing the ability to scientifically participate in a fusion experiment remotely has been growing in size in an attempt to better address the needs of fusion scientists worldwide. The natural progression of this research is to examine how to move from remote scientific participation to remote hardware control. The vision is to define a gatekeeper software system that will be the only channel of interaction for incoming requests to the secured area of the experimental site. The role of the gatekeeper is to validate the identification and access privilege of the requestor and to insure the general validity of the proposed request. The vision for the gatekeeper is that it be a modular system that is simple in design and defined in a way that makes its implementation and operation transparent and obvious. The architecture of the module interface is flexible enough that it can easily allow the future addition of new modules. At the same time, it should be transparent to end-users and allow a high volume of activity so as to not provide a work bottleneck. The results of the gatekeeper design and initial implementation are presented as well as a discussion on the implication of this research on the operation of fusion experimental machines such as ITER.

An investigation of secure remote instrument control

Energy Technology Data Exchange (ETDEWEB)

Schissel, D.P., E-mail: schissel@fusion.gat.co [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Abla, G. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Fredian, T.; Greenwald, M. [Massachusetts Institute of Technology, Cambridge, MA (United States); Penaflor, B.G. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Stillerman, J. [Massachusetts Institute of Technology, Cambridge, MA (United States); Walker, M.L. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Ciarlette, D.J. [US ITER Project Office, Oak Ridge National Laboratory, Oak Ridge, TN (United States)

2010-07-15

This paper examines the computer science issues associated with secure remote instrumentation control for magnetic fusion experiments. Computer science research into enhancing the ability to scientifically participate in a fusion experiment remotely has been growing in size in an attempt to better address the needs of fusion scientists worldwide. The natural progression of this research is to examine how to move from remote scientific participation to remote hardware control. The vision is to define a gatekeeper software system that will be the only channel of interaction for incoming requests to the secured area of the experimental site. The role of the gatekeeper is to validate the identification and access privilege of the requestor and to insure the general validity of the proposed request. The vision for the gatekeeper is that it be a modular system that is simple in design and defined in a way that makes its implementation and operation transparent and obvious. The architecture of the module interface is flexible enough that it can easily allow the future addition of new modules. At the same time, it should be transparent to end-users and allow a high volume of activity so as to not provide a work bottleneck. The results of the gatekeeper design and initial implementation are presented as well as a discussion on the implication of this research on the operation of fusion experimental machines such as ITER.

A briefing to verification and validation of computer software

International Nuclear Information System (INIS)

Zhang Aisen; Xie Yalian

2012-01-01

Nowadays, the computer equipment and information processing technology is coming into the engineering of instrument and process control. Owing to its convenient and other advantages, more and more utilities are more than happy to use it. After initial utilization in basic functional controlling, the computer equipment and information processing technology is widely used in safety critical control. Consequently, the people pay more attentions to the quality of computer software. How to assess and ensure its quality are the most concerned problems. The verification and validation technology of computer software are important steps to the quality assurance. (authors)

The 2007 ESO Instrument Calibration Workshop

CERN Document Server

Kaufer, Andreas; ESO Workshop

2008-01-01

The 2007 ESO Instrument Calibration workshop brought together more than 120 participants with the objective to a) foster the sharing of information, experience and techniques between observers, instrument developers and instrument operation teams, b) review the actual precision and limitations of the applied instrument calibration plans, and c) collect the current and future requirements by the ESO users. These present proceedings include the majority of the workshop’s contributions and document the status quo of instrument calibration at ESO in large detail. Topics covered are: Optical Spectro-Imagers, Optical Multi-Object Spectrographs, NIR and MIR Spectro-Imagers, High-Resolution Spectrographs, Integral Field Spectrographs, Adaptive Optics Instruments, Polarimetric Instruments, Wide Field Imagers, Interferometric Instruments as well as other crucial aspects such as data flow, quality control, data reduction software and atmospheric effects. It was stated in the workshop that "calibration is a life-long l...

Distributed controller clustering in software defined networks.

Directory of Open Access Journals (Sweden)

Ahmed Abdelaziz

Full Text Available Software Defined Networking (SDN is an emerging promising paradigm for network management because of its centralized network intelligence. However, the centralized control architecture of the software-defined networks (SDNs brings novel challenges of reliability, scalability, fault tolerance and interoperability. In this paper, we proposed a novel clustered distributed controller architecture in the real setting of SDNs. The distributed cluster implementation comprises of multiple popular SDN controllers. The proposed mechanism is evaluated using a real world network topology running on top of an emulated SDN environment. The result shows that the proposed distributed controller clustering mechanism is able to significantly reduce the average latency from 8.1% to 1.6%, the packet loss from 5.22% to 4.15%, compared to distributed controller without clustering running on HP Virtual Application Network (VAN SDN and Open Network Operating System (ONOS controllers respectively. Moreover, proposed method also shows reasonable CPU utilization results. Furthermore, the proposed mechanism makes possible to handle unexpected load fluctuations while maintaining a continuous network operation, even when there is a controller failure. The paper is a potential contribution stepping towards addressing the issues of reliability, scalability, fault tolerance, and inter-operability.

Distributed controller clustering in software defined networks.

Science.gov (United States)

Abdelaziz, Ahmed; Fong, Ang Tan; Gani, Abdullah; Garba, Usman; Khan, Suleman; Akhunzada, Adnan; Talebian, Hamid; Choo, Kim-Kwang Raymond

2017-01-01

Software Defined Networking (SDN) is an emerging promising paradigm for network management because of its centralized network intelligence. However, the centralized control architecture of the software-defined networks (SDNs) brings novel challenges of reliability, scalability, fault tolerance and interoperability. In this paper, we proposed a novel clustered distributed controller architecture in the real setting of SDNs. The distributed cluster implementation comprises of multiple popular SDN controllers. The proposed mechanism is evaluated using a real world network topology running on top of an emulated SDN environment. The result shows that the proposed distributed controller clustering mechanism is able to significantly reduce the average latency from 8.1% to 1.6%, the packet loss from 5.22% to 4.15%, compared to distributed controller without clustering running on HP Virtual Application Network (VAN) SDN and Open Network Operating System (ONOS) controllers respectively. Moreover, proposed method also shows reasonable CPU utilization results. Furthermore, the proposed mechanism makes possible to handle unexpected load fluctuations while maintaining a continuous network operation, even when there is a controller failure. The paper is a potential contribution stepping towards addressing the issues of reliability, scalability, fault tolerance, and inter-operability.

Software control and system configuration management - A process that works

Science.gov (United States)

Petersen, K. L.; Flores, C., Jr.

1983-01-01

A comprehensive software control and system configuration management process for flight-crucial digital control systems of advanced aircraft has been developed and refined to insure efficient flight system development and safe flight operations. Because of the highly complex interactions among the hardware, software, and system elements of state-of-the-art digital flight control system designs, a systems-wide approach to configuration control and management has been used. Specific procedures are implemented to govern discrepancy reporting and reconciliation, software and hardware change control, systems verification and validation testing, and formal documentation requirements. An active and knowledgeable configuration control board reviews and approves all flight system configuration modifications and revalidation tests. This flexible process has proved effective during the development and flight testing of several research aircraft and remotely piloted research vehicles with digital flight control systems that ranged from relatively simple to highly complex, integrated mechanizations.

Software control and system configuration management: A systems-wide approach

Science.gov (United States)

Petersen, K. L.; Flores, C., Jr.

1984-01-01

A comprehensive software control and system configuration management process for flight-crucial digital control systems of advanced aircraft has been developed and refined to insure efficient flight system development and safe flight operations. Because of the highly complex interactions among the hardware, software, and system elements of state-of-the-art digital flight control system designs, a systems-wide approach to configuration control and management has been used. Specific procedures are implemented to govern discrepancy reporting and reconciliation, software and hardware change control, systems verification and validation testing, and formal documentation requirements. An active and knowledgeable configuration control board reviews and approves all flight system configuration modifications and revalidation tests. This flexible process has proved effective during the development and flight testing of several research aircraft and remotely piloted research vehicles with digital flight control systems that ranged from relatively simple to highly complex, integrated mechanizations.

Fault tree analysis of KNICS RPS software

International Nuclear Information System (INIS)

Park, Gee Yong; Kwon, Kee Choon; Koh, Kwang Yong; Jee, Eun Kyoung; Seong, Poong Hyun; Lee, Dae Hyung

2008-01-01

This paper describes the application of a software Fault Tree Analysis (FTA) as one of the analysis techniques for a Software Safety Analysis (SSA) at the design phase and its analysis results for the safety-critical software of a digital reactor protection system, which is called the KNICS RPS, being developed in the KNICS (Korea Nuclear Instrumentation and Control Systems) project. The software modules in the design description were represented by Function Blocks (FBs), and the software FTA was performed based on the well-defined fault tree templates for the FBs. The SSA, which is part of the verification and validation (V and V) activities, was activated at each phase of the software lifecycle for the KNICS RPS. At the design phase, the software HAZOP (Hazard and Operability) and the software FTA were employed in the SSA in such a way that the software HAZOP was performed first and then the software FTA was applied. The software FTA was applied to some critical modules selected from the software HAZOP analysis

Digital study of nuclear reactor instrument

International Nuclear Information System (INIS)

Lv Gongxiang; Yang Zhijun

2006-01-01

The paper introduces the design method of nuclear reactor's digital instrument developed by authors based on the AT89C52 single chip microcomputer. Also the instrument system hardware structure and software framework are given. The instrument apply DDC112 which is responsible for the measure of lower current. When designing the instrument system, anti-interference measure of software, especially hardware is considered seriously. (authors)

Evolution of the VLT instrument control system toward industry standards

Science.gov (United States)

Kiekebusch, Mario J.; Chiozzi, Gianluca; Knudstrup, Jens; Popovic, Dan; Zins, Gerard

2010-07-01

The VLT control system is a large distributed system consisting of Linux Workstations providing the high level coordination and interfaces to the users, and VME-based Local Control Units (LCU's) running the VxWorks real-time operating system with commercial and proprietary boards acting as the interface to the instrument functions. After more than 10 years of VLT operations, some of the applied technologies used by the astronomical instruments are being discontinued making it difficult to find adequate hardware for future projects. In order to deal with this obsolescence, the VLT Instrumentation Framework is being extended to adopt well established Commercial Off The Shelf (COTS) components connected through industry standard fieldbuses. This ensures a flexible state of the art hardware configuration for the next generation VLT instruments allowing the access to instrument devices via more compact and simpler control units like PC-based Programmable Logical Controllers (PLC's). It also makes it possible to control devices directly from the Instrument Workstation through a normal Ethernet connection. This paper outlines the requirements that motivated this work, as well as the architecture and the design of the framework extension. In addition, it describes the preliminary results on a use case which is a VLTI visitor instrument used as a pilot project to validate the concepts and the suitability of some COTS products like a PC-based PLCs, EtherCAT8 and OPC UA6 as solutions for instrument control.

Continuous integration and quality control for scientific software

Science.gov (United States)

Neidhardt, A.; Ettl, M.; Brisken, W.; Dassing, R.

2013-08-01

Modern software has to be stable, portable, fast and reliable. This is going to be also more and more important for scientific software. But this requires a sophisticated way to inspect, check and evaluate the quality of source code with a suitable, automated infrastructure. A centralized server with a software repository and a version control system is one essential part, to manage the code basis and to control the different development versions. While each project can be compiled separately, the whole code basis can also be compiled with one central “Makefile”. This is used to create automated, nightly builds. Additionally all sources are inspected automatically with static code analysis and inspection tools, which check well-none error situations, memory and resource leaks, performance issues, or style issues. In combination with an automatic documentation generator it is possible to create the developer documentation directly from the code and the inline comments. All reports and generated information are presented as HTML page on a Web server. Because this environment increased the stability and quality of the software of the Geodetic Observatory Wettzell tremendously, it is now also available for scientific communities. One regular customer is already the developer group of the DiFX software correlator project.

Quality control of nuclear medicine instruments, 1991

International Nuclear Information System (INIS)

1996-12-01

This document gives detailed guidance on the quality control of various instruments used in nuclear medicine. A first preliminary document was drawn up in 1979. A revised and extended version, incorporating recommended procedures, test schedules and protocols was prepared in 1982. The first edition of 'Quality Control of Nuclear Medicine Instruments', IAEA-TECDOC-317, was printed in late 1984. Recent advances in the field of nuclear medicine imaging made it necessary to add a chapter on Camera-Computer Systems and another on SPECT Systems

Quality control of nuclear medicine instruments 1991

International Nuclear Information System (INIS)

1991-05-01

This document gives detailed guidance on the quality control of various instruments used in nuclear medicine. A first preliminary document was drawn up in 1979. A revised and extended version, incorporating recommended procedures, test schedules and protocols was prepared in 1982. The first edition of ''Quality Control of Nuclear Medicine Instruments'', IAEA-TECDOC-317, was printed in late 1984. Recent advances in the field of nuclear medicine imaging made it necessary to add a chapter on Camera-Computer Systems and another on SPECT Systems. Figs and tabs

Planning instruments to control urban growth

DEFF Research Database (Denmark)

Jørgensen, Gertrud; Nielsen, Thomas Alexander Sick

2010-01-01

It is challenging to plan and control urban development in peri-urban areas. But if no planning is done, the result will often be unsustainable, including widespread, dispersed and uncoordinated urban growth. Spatial planning based on zoning remains the most important planning instrument and its...... success depend on regional coordination. Incentive based instruments may contrbute to growth management, but only few examples are available and their effects on urban growth patterns yet to be seen....

A control system verifier using automated reasoning software

International Nuclear Information System (INIS)

Smith, D.E.; Seeman, S.E.

1985-08-01

An on-line, automated reasoning software system for verifying the actions of other software or human control systems has been developed. It was demonstrated by verifying the actions of an automated procedure generation system. The verifier uses an interactive theorem prover as its inference engine with the rules included as logical axioms. Operation of the verifier is generally transparent except when the verifier disagrees with the actions of the monitored software. Testing with an automated procedure generation system demonstrates the successful application of automated reasoning software for verification of logical actions in a diverse, redundant manner. A higher degree of confidence may be placed in the verified actions of the combined system

Integrated Instrumentation and Control Upgrade Plan

International Nuclear Information System (INIS)

Wilkinson, D.; Sun, B.; Wray, L.; Smith, J.

1992-02-01

This document presents the first industry-wide integrated research and development plan to support upgrading instrumentation and control (I ampersand C) systems in nuclear power plants in the United States. The plan encompasses both solving obsolescence problems and introducing modern I ampersand C technology into the industry. Accomplishing this plan will provide the technological base to modernize existing plants, as well as bridge the gap to meet Advanced Light Water Reactor (ALWR) requirements for modern I ampersand C systems. This plan defines Research and Development tasks to meet the identified needs for the following technical elements: Instrumentation, Control and Protection, Man-Machine Support Systems, Maintenance, Communications, Verification and Validation, and Specifications and Standards

Software management of the LHC Detector Control Systems

CERN Document Server

Varela, F

2007-01-01

The control systems of each of the four Large Hadron Collider (LHC) experiments will contain of the order of 150 computers running the back-end applications. These applications will have to be maintained and eventually upgraded during the lifetime of the experiments, ~20 years. This paper presents the centralized software management strategy adopted by the Joint COntrols Project (JCOP) [1], which is based on a central database that holds the overall system configuration. The approach facilitates the integration of different parts of a control system and provides versioning of its various software components. The information stored in the configuration database can eventually be used to restore a computer in the event of failure.

Software management of the LHC detector control systems

CERN Document Server

Varela, F

2007-01-01

The control systems of each of the four Large Hadron Collider (LHC) experiments will contain of the order of 150 computers running the back-end applications. These applications will have to be maintained and eventually upgraded during the lifetime of the experiments, ~20 years. This paper presents the centralized software management strategy adopted by the Joint COntrols Project (JCOP) [1], which is based on a central database that holds the overall system configuration. The approach facilitates the integration of different parts of a control system and provides versioning of its various software components. The information stored in the configuration database can eventually be used to restore a computer in the event of failure.

Software metrics: The key to quality software on the NCC project

Science.gov (United States)

Burns, Patricia J.

1993-01-01

Network Control Center (NCC) Project metrics are captured during the implementation and testing phases of the NCCDS software development lifecycle. The metrics data collection and reporting function has interfaces with all elements of the NCC project. Close collaboration with all project elements has resulted in the development of a defined and repeatable set of metrics processes. The resulting data are used to plan and monitor release activities on a weekly basis. The use of graphical outputs facilitates the interpretation of progress and status. The successful application of metrics throughout the NCC project has been instrumental in the delivery of quality software. The use of metrics on the NCC Project supports the needs of the technical and managerial staff. This paper describes the project, the functions supported by metrics, the data that are collected and reported, how the data are used, and the improvements in the quality of deliverable software since the metrics processes and products have been in use.

Outline of the requirements of application of computer based instrumentation and control systems in the systems important to safety on Bohunice NPPs

International Nuclear Information System (INIS)

Bacurik, J.

1997-01-01

The most important regulatory requirements and issues are described related to the review, evaluation and assessment of computer-based safety-related IandC systems, with emphasis on safety instrumentation and control. These aspects include safety classification and categorization of IandC, ranking of applicable codes and standards, design evaluation on the system level, and software assessment. (author)

Survey and analysis on environmental and electromagnetic effect on instrumentation and control equipment of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Hwang, In Koo; Lee, Dong Young; Cha, Kyung Ho

2001-03-01

As the instrumentation and control (I and C) equipment suppliers tend to provide digital components rather than conventional analog type components for instrumentation and control systems of nuclear power plants(NPPs), it is unavoidable to adopt digital equipment for safety I and C systems as well as non-safety systems. However, the full introduction of digital equipment for I and C systems of nuclear power plants raises several concerns which have not been considered in conventional analog I and C equipment. The two major examples of the issues of digital systems are environmental/electromagnetic compatibility (EMC) and software reliability. This report presents the survey and research results on environmental and electromagnetic effect on I and C equipment of nuclear power plants to give a guideline for aging management and design process. Electromagnetic site surveys were conducted to be used as a part of technical basis to demonstrate that I and C systems are compatible with the ambient electromagnetic noise in Korean nuclear power plants.

Proceedings: Electromagnetic interference control in modern digital instrumentation and control upgrades

International Nuclear Information System (INIS)

1993-06-01

A workshop on Electro-Magnetic Interference (EMI) Control in Modern Digital Instrumentation ampersand Control System Upgrade was held in Baltimore on September 10-11, 1992 to provide a forum for technology transfer, technical information exchange, and education. The workshop was attended by more than 70 representatives of electric utilities, equipment manufacturers, engineering consulting organizations, and government agencies. The workshop consists of four sessions: (1) Organizational EMC Perspectives, (2) EMI Environment, Case Histories ampersand Solutions, (3) EMC in Digital Instrumentation ampersand Control Systems, and (4) EMI Utility Needs. A group discussion followed the presentations to identify utility needs. Individual papers have been cataloged separately

Realization of computer-controlled CAMAC model through the technology of virtual instrument

International Nuclear Information System (INIS)

Le Yi; Li Cheng; Liao Juanjuan; Zhou Xin

1997-01-01

The author is to introduce virtual instrument system and basic features of its typical software development platform, and show this system's superiority and fitness to physical experiments by the example of the CAMAC model ADC2249A, which is often used in nuclear physics experiments

Ground control station software design for micro aerial vehicles

Science.gov (United States)

Walendziuk, Wojciech; Oldziej, Daniel; Binczyk, Dawid Przemyslaw; Slowik, Maciej

2017-08-01

This article describes the process of designing the equipment part and the software of a ground control station used for configuring and operating micro unmanned aerial vehicles (UAV). All the works were conducted on a quadrocopter model being a commonly accessible commercial construction. This article contains a characteristics of the research object, the basics of operating the micro aerial vehicles (MAV) and presents components of the ground control station model. It also describes the communication standards for the purpose of building a model of the station. Further part of the work concerns the software of the product - the GIMSO application (Generally Interactive Station for Mobile Objects), which enables the user to manage the actions and communication and control processes from the UAV. The process of creating the software and the field tests of a station model are also presented in the article.

Guidance and Control Software Project Data - Volume 4: Configuration Management and Quality Assurance Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes configuration management and quality assurance documents from the GCS project. Volume 4 contains six appendices: A. Software Accomplishment Summary for the Guidance and Control Software Project; B. Software Configuration Index for the Guidance and Control Software Project; C. Configuration Management Records for the Guidance and Control Software Project; D. Software Quality Assurance Records for the Guidance and Control Software Project; E. Problem Report for the Pluto Implementation of the Guidance and Control Software Project; and F. Support Documentation Change Reports for the Guidance and Control Software Project.

Timing system control software in the SLC

International Nuclear Information System (INIS)

Thompson, K.; Phinney, N.

1985-04-01

A new timing system that allows precision (approx.1 to 2 ns) control of the trigger times of klystrons, beam position monitors, and other devices on a pulse-to-pulse basis at up to 360 Hz is in operation in the first third of the SLAC linear accelerator. The control software is divided between a central host VAX and local Intel 8086-based microprocessor clusters. Facilities exist to set up and adjust the timing of devices or groups of devices independently for beam pulses having different destinations and purposes, which are run in an interlaced fashion during normal machine operation. Upgrading of the system is currently underway, using a new version of the Programmable Delay Unit CAMAC module to allow pipelining of timing information for three machine pulses. An overview of the current state of the system is presented in this paper, with an emphasis on software control

Malaysian Preparation for Nuclear Power Plant Instrumentation and Control System

International Nuclear Information System (INIS)

Mohd Idris Taib; Nurfarhana Ayuni Joha; Kamarudin Sulaiman; Izhar Abu Hussin

2011-01-01

Instrumentation and Control System is required in Nuclear Power Plant for their safe and effective operation. The system is combination and integrated from detectors, actuators, analog system as well as digital system. Current design of system definitely follows of electronic as well as computer technology, with strictly follow regulation and guideline from local regulator as well as International Atomic Energy Agency. Commercial Off-The-Shelf products are extensively used with specific nucleonic instrumentation. Malaysian experiences depend on Reactor TRIGA PUSPATI Instrumentation and Control, Power Plant Instrumentation and Control as well as Process Control System. However Malaysians have capabilities to upgrade themself from Electronics, Computers, Electrical and Mechanical based. Proposal is presented for Malaysian preparation. (author)

The software quality control for gamma spectrometry

International Nuclear Information System (INIS)

Monte, L.

1986-01-01

One of major problems with wich the quality control program of an environmental measurements laboratory is confronted is the evaluation of the performances of software packages for the analysis of gamma-ray spectra. A program of tests for evaluating the performances of the software package (SPECTRAN-F, Canberra Inc.) used by our laboratory is being carried out. In this first paper the results of a preliminary study concerning the evaluation of the performance of the doublet analysis routine are presented

Real-time Control Mediation in Agile Distributed Software Development

DEFF Research Database (Denmark)

Persson, John Stouby; Aaen, Ivan; Mathiassen, Lars

2008-01-01

Agile distributed environments pose particular challenges related to control of quality and collaboration in software development. Moreover, while face-to-face interaction is fundamental in agile development, distributed environments must rely extensively on mediated interactions. On this backdrop...... control was mediated over distance by technology through real-time exchanges. Contrary to previous research, the analysis suggests that both formal and informal elements of real-time mediated control were used; that evolving goals and adjustment of expectations were two of the main issues in real......-time mediated control exchanges; and, that the actors, despite distances in space and culture, developed a clan-like pattern mediated by technology to help control quality and collaboration in software development....

Radioisotope thermoelectric generator transportation system subsystem 143 software development plan

International Nuclear Information System (INIS)

King, D.A.

1994-01-01

This plan describes the activities to be performed and the controls to be applied to the process of specifying, developing, and qualifying the data acquisition software for the Radioisotope Thermoelectric Generator (RTG) Transportation System Subsystem 143 Instrumentation and Data Acquisition System (IDAS). This plan will serve as a software quality assurance plan, a verification and validation (V and V) plan, and a configuration management plan

The Development of Point Doppler Velocimeter Data Acquisition and Processing Software

Science.gov (United States)

Cavone, Angelo A.

2008-01-01

In order to develop efficient and quiet aircraft and validate Computational Fluid Dynamic predications, aerodynamic researchers require flow parameter measurements to characterize flow fields about wind tunnel models and jet flows. A one-component Point Doppler Velocimeter (pDv), a non-intrusive, laser-based instrument, was constructed using a design/develop/test/validate/deploy approach. A primary component of the instrument is software required for system control/management and data collection/reduction. This software along with evaluation algorithms, advanced pDv from a laboratory curiosity to a production level instrument. Simultaneous pDv and pitot probe velocity measurements obtained at the centerline of a flow exiting a two-inch jet, matched within 0.4%. Flow turbulence spectra obtained with pDv and a hot-wire detected the primary and secondary harmonics with equal dynamic range produced by the fan driving the flow. Novel,hardware and software methods were developed, tested and incorporated into the system to eliminate and/or minimize error sources and improve system reliability.

Automation of the software production process for multiple cryogenic control applications

OpenAIRE

Fluder, Czeslaw; Lefebvre, Victor; Pezzetti, Marco; Plutecki, Przemyslaw; Tovar-González, Antonio; Wolak, Tomasz

2018-01-01

The development of process control systems for the cryogenic infrastructure at CERN is based on an automatic software generation approach. The overall complexity of the systems, their frequent evolution as well as the extensive use of databases, repositories, commercial engineering software and CERN frameworks have led to further efforts towards improving the existing automation based software production methodology. A large number of control system upgrades were successfully performed for th...

Worldwide collaborative efforts in plasma control software development

International Nuclear Information System (INIS)

Penaflor, B.G.; Ferron, J.R.; Walker, M.L.; Humphreys, D.A.; Leuer, J.A.; Piglowski, D.A.; Johnson, R.D.; Xiao, B.J.; Hahn, S.H.; Gates, D.A.

2008-01-01

This presentation will describe the DIII-D collaborations with various tokamak experiments throughout the world which have adapted custom versions of the DIII-D plasma control system (PCS) software for their own use. Originally developed by General Atomics for use on the DIII-D tokamak, the PCS has been successfully installed and used for the NSTX experiment in Princeton, the MAST experiment in Culham UK, the EAST experiment in China, and the Pegasus experiment in the University of Wisconsin. In addition to these sites, a version of the PCS is currently being developed for use by the KSTAR tokamak in Korea. A well-defined and robust PCS software infrastructure has been developed to provide a common foundation for implementing the real-time data acquisition and feedback control codes. The PCS infrastructure provides a flexible framework that has allowed the PCS to be easily adapted to fulfill the unique needs of each site. The software has also demonstrated great flexibility in allowing for different computing, data acquisition and real-time networking hardware to be used. A description of the current PCS software architecture will be given along with experiences in developing and supporting the various PCS installations throughout the world

Hardware replacements and software tools for digital control computers

International Nuclear Information System (INIS)

Walker, R.A.P.; Wang, B-C.; Fung, J.

1996-01-01

Technological obsolescence is an on-going challenge for all computer use. By design, and to some extent good fortune, AECL has had a good track record with respect to the march of obsolescence in CANDU digital control computer technology. Recognizing obsolescence as a fact of life, AECL has undertaken a program of supporting the digital control technology of existing CANDU plants. Other AECL groups are developing complete replacement systems for the digital control computers, and more advanced systems for the digital control computers of the future CANDU reactors. This paper presents the results of the efforts of AECL's DCC service support group to replace obsolete digital control computer and related components and to provide friendlier software technology related to the maintenance and use of digital control computers in CANDU. These efforts are expected to extend the current lifespan of existing digital control computers through their mandated life. This group applied two simple rules; the product, whether new or replacement should have a generic basis, and the products should be applicable to both existing CANDU plants and to 'repeat' plant designs built using current design guidelines. While some exceptions do apply, the rules have been met. The generic requirement dictates that the product should not be dependent on any brand technology, and should back-fit to and interface with any such technology which remains in the control design. The application requirement dictates that the product should have universal use and be user friendly to the greatest extent possible. Furthermore, both requirements were designed to anticipate user involvement, modifications and alternate user defined applications. The replacements for hardware components such as paper tape reader/punch, moving arm disk, contact scanner and Ramtek are discussed. The development of these hardware replacements coincide with the development of a gateway system for selected CANDU digital control

Balancing technical and regulatory concerns related to testing and control of performance assessment software

International Nuclear Information System (INIS)

Seitz, R.R.; Matthews, S.D.; Kostelnik, K.M.

1990-01-01

What activities are required to assure that a performance assessment (PA) computer code operates as it is intended? Answers to this question will vary depending on the individual's area of expertise. Different perspectives on testing and control of PA software are discussed based on interpretations of the testing and control process associated with the different involved parties. This discussion leads into the presentation of a general approach to software testing and control that address regulatory requirements. Finally, the need for balance between regulatory and scientific concerns is illustrated through lessons learned in previous implementations of software testing and control programs. Configuration control and software testing are required to provide assurance that a computer code performs as intended. Configuration control provides traceability and reproducibility of results produced with PA software and provides a system to assure that users have access to the current version of the software. Software testing is conducted to assure that the computer code has been written properly, solution techniques have been properly implemented, and the software is capable of representing the behavior of the specific system to be modeled. Comprehensive software testing includes: software analysis, verification testing, benchmark testing, and site-specific calibration/validation testing

Development of nuclear imaging instrument and software

International Nuclear Information System (INIS)

Kim, Jang Hee; Chung Jae Myung; Nam, Sang Won; Chang, Hyung Uk

1999-03-01

In the medical diagnosis, the nuclear medical instrument using the radioactive isotope are commonly utilized. In the foreign countries, the medical application and development of the most advanced nuclear medical instrument such as Single Photon Emission Computer Tomography (SPECT) and position emission tomograph (PET), have been extensively carried out. However, in Korea, such highly expensive instruments have been all, imported, paying foreign currency. Since 1997, much efforts, the development of the radio nuclide medical instrument, the drive of the domestic production, etc. have been made to establish our own technologies and to balance the international payments under the support of the Ministry of Science and Technology. At present time, 180 nuclear imaging instruments are now in operation and 60 of them are analog camera. In analog camera, the vector X-Y monitor is need for are image display. Since the analog camera, signal can not be process in the digital form, we have difficulties to transfer and store the image data. The image displayed at the monitor must be stored in the form of polaroid or X ray film. In order to discard these disadvantages, if we developed the computer interface system, the performance analog camera will be comparable with that of the digital camera. The final objective of the research is that using the interface system developed in this research, we reconstruct the image data transmitted to the personal computer in the form of the generalized data file

Two viewpoints for software failures and their relation in probabilistic safety assessment of digital instrumentation and control systems

International Nuclear Information System (INIS)

Kim, Man Cheol

2015-01-01

As the use of digital systems in nuclear power plants increases, the reliability of the software becomes one of the important issues in probabilistic safety assessment. In this paper, two viewpoints for a software failure during the operation of a digital system or a statistical software test are identified, and the relation between them is provided. In conventional software reliability analysis, a failure is mainly viewed with respect to the system operation. A new viewpoint with respect to the system input is suggested. The failure probability density functions for the two viewpoints are defined, and the relation between the two failure probability density functions is derived. Each failure probability density function can be derived from the other failure probability density function by applying the derived relation between the two failure probability density functions. The usefulness of the derived relation is demonstrated by applying it to the failure data obtained from the software testing of a real system. The two viewpoints and their relation, as identified in this paper, are expected to help us extend our understanding of the reliability of safety-critical software. (author)

Software para Controle de Temperatura em Estufas

OpenAIRE

Silva, Antonio Carlos Alves; Universidade Federal de Lavras; Kanazawa, Edna Mie; Universidade Federal de Lavras; de Carvalho, Karina Dutra; Universidade Federal de Lavras; Kinoshita, Vanessa Godoy; Universidade Federal de Lavras; Uchoa, Joaquim Quinteiro; Universidade Federal de Lavras; Lacerda, Wilian Soares; Universidade Federal de Lavras; Schneider, Bruno de Oliveira; Universidade Federal de Lavras

2004-01-01

Neste trabalho é apresentado o projeto desenvolvido para controle de temperatura em estufas, denominado CTE, utilizando uma Interface de Aquisição e Controle de Dados. Todo o controle é feito via software, onde pode-se optar por dois tipos de controle: o controle automático, onde é possível definir-se a temperatura mínima e máxima; ou o controle manual, onde o usuário poderá optar por acionar periféricos de aquecimento, resfriamento e desligamento da estufa. Foi desenvolvida também uma interf...

Qt based control system software for Low Energy Accelerator Facility

International Nuclear Information System (INIS)

Basu, A.; Singh, S.; Nagraju, S.B.V.; Gupta, S.; Singh, P.

2012-01-01

Qt based control system software for Low Energy Accelerating Facility (LEAF) is operational at Bhabha Atomic Research Centre (BARC), Trombay, Mumbai. LEAF is a 50 keV negative ion electrostatic accelerator based on SNICS ion source. Control system uses Nokia Trolltech's QT 4.x API for control system software. Ni 6008 USB based multifunction cards has been used for control and read back field equipments such as power supplies, pumps, valves etc. Control system architecture is designed to be client server. Qt is chosen for its excellent GUI capability and platform independent nature. Control system follows client server architecture. The paper will describe the control system. (author)

Nuclear power plant control and instrumentation 1982. Proceedings of an international symposium on nuclear power plant control and instrumentation

International Nuclear Information System (INIS)

1983-01-01

Ever increasing demands for nuclear power plant safety and availability imply a need for the introduction of modern measurement and control methods, together with data processing techniques based on the latest advances in electronic components, transducers and computers. Nuclear power plant control and instrumentation is therefore an extremely rapidly developing field. The present symposium, held in Munich, FR Germany, was prepared with the help of the IAEA International Working Group on Nuclear Power Plant Control and Instrumentation and organized in close co-operation with the Gesellschaft fur Reaktorsicherheit, Federal Republic of Germany. A number of developments were highlighted at the Munich symposium: - The increased use of computers can bring clear advantages and this technique is now proven as a tool for supervising and controlling plant operation. Advanced computerized systems for operator support are being developed on a large scale in many countries. The progress in this field is quite obvious, especially in disturbance analysis, safety parameter display, plant operator guidance and plant diagnostics. The new trend of introducing computers and microprocessors in protection systems makes it easy to implement 'defence-in-depth' strategies which give better assurance of correct system responses and also prevent unnecessary reactor trips, thus improving plant availability. The introduction of computerized systems for control of reactor power, reactor water level and reactor pressure as well as for reactor start-up and shut-down could improve the reliability and availability of nuclear power plants. The rapid technical development in the area of control and instrumentation makes it necessary to plan for at least one replacement of obsolete equipment in the course of the 30 years lifetime of a nuclear power plant and retrofitting of currently operating reactors with new control systems. Major design improvements and regulatory requirements also require

Supervisory control software for MFTF neutral beams

International Nuclear Information System (INIS)

Woodruff, J.P.

1981-01-01

We describe the software structures that control the operation of MFTF Sustaining Neutral Beam Power Supplies (SNBPS). These components of the Supervisory Control and Diagnostics System (SCDS) comprise ten distinct tasks that exist in the SCDS system environment. The codes total about 16,000 lines of commented Pascal code and occupy 240 kbytes of memory. The controls have been running since March 1981, and at this writing are being integrated to the Local Control System and to the power supply Pulse Power Module Controller

Instrumentation and control of turbine, generator and associated systems

International Nuclear Information System (INIS)

Vogtland, U.

1982-01-01

The purpose of this presentation is to give some information on Instrumentation and Control (I and C) for turbine-generators, in this case for nuclear application. The I and C scope of supply for such a turbine-generator can be divided as follows: - Closed-loop controls - Turbine stress control systems - Supervisory instrumentation - Protection systems - Open-loop controls. The main systems used for nuclear application are presented by means of examples taken from these a.m. categories. (orig./RW)

Measurement control program for NDA instruments

International Nuclear Information System (INIS)

Hsue, S.T.; Marks, T.

1983-01-01

Measurement control checks for nondestructive assay instruments have been a constant and continuing concern at Los Alamos National Laboratory. This paper summarizes the evolution of the measurement control checks in the various high-resolution gamma systems we have developed. In-plant experiences with these systems and checks will be discussed. Based on these experiences, a set of measurement control checks is recommended for high-resolution gamma-ray systems

New control system: ADA softwares organization

International Nuclear Information System (INIS)

David, L.

1992-01-01

On VAX/VMS, ADA compiler is integrated in a workshop of ACS software engineering which allows a coherent development by control of source and executable programs, by separation of applications in various levels of visibility and by management of existing links between different modules of a same application. (A.B.)

WLS software for the Los Alamos geophysical instrumentation truck

International Nuclear Information System (INIS)

Ideker, C.D.; LaDelfe, C.M.

1985-01-01

Los Alamos National Laboratory's capabilities for special downhole geophysical well logging has increased steadily over the past few years. Software was developed originally for each individual tool as it became operational. With little or no standardization for tool software modules, software development became redundant, time consuming, and cost ineffective. With long-term use and the rapid evolution of well logging capacity in mind. Los Alamos and EG and G personnel decided to purchase a software system. The system was designed to offer: wide-range use and programming flexibility; standardization subroutines for tool module development; user friendly operation which would reduce training time; operator error checking and alarm activation; maximum growth capacity for new tools as they are added to the inventory; and the ability to incorporate changes made to the computer operating system and hardware. The end result is a sophisticated and flexible software tool and for transferring downhole geophysical measurement data to computer disk files. This paper outlines the need, design, development, and implementation of the WLS software for geophysical data acquisition. A demonstration and working examples are included in the presentation

Software-Defined Congestion Control Algorithm for IP Networks

Directory of Open Access Journals (Sweden)

Yao Hu

2017-01-01

Full Text Available The rapid evolution of computer networks, increase in the number of Internet users, and popularity of multimedia applications have exacerbated the congestion control problem. Congestion control is a key factor in ensuring network stability and robustness. When the underlying network and flow information are unknown, the transmission control protocol (TCP must increase or reduce the size of the congestion window to adjust to the changes of traffic in the Internet Protocol (IP network. However, it is possible that a software-defined approach can relieve the network congestion problem more efficiently. This approach has the characteristic of centralized control and can obtain a global topology for unified network management. In this paper, we propose a software-defined congestion control (SDCC algorithm for an IP network. We consider the difference between TCP and the user datagram protocol (UDP and propose a new method to judge node congestion. We initially apply the congestion control mechanism in the congested nodes and then optimize the link utilization to control network congestion.

Development of NPTC-11 intelligence control instrument with digital display

International Nuclear Information System (INIS)

Wang Chengming; Pu Li; Yu Jiang; Xue Yuping; Zhang Bo; Chen Yong

2007-01-01

The accurate of the process control gauge has direct influence on the safe operation of nuclear power plants. Therefore it is necessary to accumulate experiences for the domestic development of this Instrument. In this paper, NPTC-11 intelligence control Instrument with digital display is developed based on the design code for nuclear Instrument, considering the actual application requirements and technical redundancy. Its application in nuclear power plant for almost one year indicates that this Instrument satisfies the development purpose and requirements. (authors)

Design concepts for a nuclear digital instrumentation and control system platform

International Nuclear Information System (INIS)

Ou, T. C.; Chen, C. K.; Chen, P. J.; Shyu, S. S.; Lee, C. L.; Hsieh, S. F.

2010-10-01

The objective of this paper is to present the development results of the nuclear instrumentation and control system in Taiwan. As the Taiwan nuclear power plants age, the need to consider upgrading of both their safety and non-safety-related instrumentation and control systems becomes more urgent. Meanwhile, the digital instrumentation and control system that is based on current fast evolving electronic and information technologies are difficult to maintain effectively. Therefore, Institute of Nuclear Energy Research was made a decision to promote the Taiwan Nuclear Instrumentation and Control System project to collaborate with domestic electronic industry to establish self-reliant capabilities on the design, manufacturing, and application of nuclear instrumentation and control systems with newer technology. In the case of safety-related applications like nuclear instrumentation and control, safety-oriented quality control is required. In order to establish a generic qualified digital platform, the world-wide licensing experience should be considered in the licensing process. This paper describes the qualification and certification tools by IEC 61508 for design and development of safety related equipment and explains the basis for many decisions made while performing the digital upgrade. (Author)

Quality assurance for software important to safety

International Nuclear Information System (INIS)

2000-01-01

Software applications play an increasingly relevant role in nuclear power plant systems. This is particularly true of software important to safety used in both: calculations for the design, testing and analysis of nuclear reactor systems (design, engineering and analysis software); and monitoring, control and safety functions as an integral part of the reactor systems (monitoring, control and safety system software). Computer technology is advancing at a fast pace, offering new possibilities in nuclear reactor design, construction, commissioning, operation, maintenance and decommissioning. These advances also present new issues which must be considered both by the utility and by the regulatory organization. Refurbishment of ageing instrumentation and control systems in nuclear power plants and new safety related application areas have emerged, with direct (e.g. interfaces with safety systems) and indirect (e.g. operator intervention) implications for safety. Currently, there exist several international standards and guides on quality assurance for software important to safety. However, none of the existing documents provides comprehensive guidance to the developer, manager and regulator during all phases of the software life-cycle. The present publication was developed taking into account the large amount of available documentation, the rapid development of software systems and the need for updated guidance on h ow to do it . It provides information and guidance for defining and implementing quality assurance programmes covering the entire life-cycle of software important to safety. Expected users are managers, performers and assessors from nuclear utilities, regulatory bodies, suppliers and technical support organizations involved with the development and use of software applied in nuclear power plants

Software for imaging phase-shift interference microscope

Science.gov (United States)

Malinovski, I.; França, R. S.; Couceiro, I. B.

2018-03-01

In recent years absolute interference microscope was created at National Metrology Institute of Brazil (INMETRO). The instrument by principle of operation is imaging phase-shifting interferometer (PSI) equipped with two stabilized lasers of different colour as traceable reference wavelength sources. We report here some progress in development of the software for this instrument. The status of undergoing internal validation and verification of the software is also reported. In contrast with standard PSI method, different methodology of phase evaluation is applied. Therefore, instrument specific procedures for software validation and verification are adapted and discussed.

Environmental Control System Software & Hardware Development

Science.gov (United States)

Vargas, Daniel Eduardo

2017-01-01

ECS hardware: (1) Provides controlled purge to SLS Rocket and Orion spacecraft. (2) Provide mission-focused engineering products and services. ECS software: (1) NASA requires Compact Unique Identifiers (CUIs); fixed-length identifier used to identify information items. (2) CUI structure; composed of nine semantic fields that aid the user in recognizing its purpose.

The graphics software of the Saclay Linear Accelerator control system

International Nuclear Information System (INIS)

Gournay, J.F.

1988-01-01

The graphics software used for the control of the Saclay Linear Accelerator is described. The specific requirements that such a software must have in this environment are outlined and some typical applications are presented. (orig.)

Control strategies used in the control software for the Heavy Ion Research Facility in Lanzhou

Energy Technology Data Exchange (ETDEWEB)

Zhou, Wen-Xiong [College of Power Engineering, Chongqing University, Chongqing 400044 (China); Postdoctoral Station, Chongqing University, Chongqing 400044 (China); Wang, Yan-Yu [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Pan, Liang-Ming [College of Power Engineering, Chongqing University, Chongqing 400044 (China); Tu, Sheng-Pan [State Grid Chongqing Maintenance Company, Chongqing 400044 (China)

2016-07-01

Automation control systems are important for the operation of an accelerator. To ensure the reliable, stable and flexible operation of the Heavy Ion Research Facility in Lanzhou (HIRFL), several control systems are developed. The developed control systems are the SECRAL control system, the LECR3 control system, the LAPECR1 control system and the Electro-Static septum control system. The corresponding control software systems are developed using Visual C++. To ensure the accuracy, stability and flexibility of the control systems, some special control strategies are developed in the control software systems. This paper provides a detailed description of the main control strategies used in the control software systems. The main control strategies are composed of a reliable communication mechanism, a correct data/command transmission mechanism, an efficient data storage mechanism and an interlock protection mechanism. To guarantee a reliable communication between the devices for the commercially purchased devices and the built in-house ones, a modified heartbeat method is developed. To provide flexible reconstitution function for the control systems, the command queue and the state machine are combined. The message mechanism and the multiple windows mechanism are also used for the module mechanism. The relevant control systems are introduced as examples of these control strategies. These systems have been running stably for several years.

Control strategies used in the control software for the Heavy Ion Research Facility in Lanzhou

International Nuclear Information System (INIS)

Zhou, Wen-Xiong; Wang, Yan-Yu; Pan, Liang-Ming; Tu, Sheng-Pan

2016-01-01

Automation control systems are important for the operation of an accelerator. To ensure the reliable, stable and flexible operation of the Heavy Ion Research Facility in Lanzhou (HIRFL), several control systems are developed. The developed control systems are the SECRAL control system, the LECR3 control system, the LAPECR1 control system and the Electro-Static septum control system. The corresponding control software systems are developed using Visual C++. To ensure the accuracy, stability and flexibility of the control systems, some special control strategies are developed in the control software systems. This paper provides a detailed description of the main control strategies used in the control software systems. The main control strategies are composed of a reliable communication mechanism, a correct data/command transmission mechanism, an efficient data storage mechanism and an interlock protection mechanism. To guarantee a reliable communication between the devices for the commercially purchased devices and the built in-house ones, a modified heartbeat method is developed. To provide flexible reconstitution function for the control systems, the command queue and the state machine are combined. The message mechanism and the multiple windows mechanism are also used for the module mechanism. The relevant control systems are introduced as examples of these control strategies. These systems have been running stably for several years.

Hardware And Software Architectures For Reconfigurable Time-Critical Control Tasks

Directory of Open Access Journals (Sweden)

Adam Piłat

2007-01-01

Full Text Available The most popular configuration of the controlled laboratory test-rigs is the personalcomputer (PC equipped with the I/O board. The dedicated software components allowsto conduct a wide range of user-defined tasks. The typical configuration functionality canbe customized by PC hardware components and their programmable reconfiguration. Thenext step in the automatic control system design is the embedded solution. Usually, thedesign process of the embedded control system is supported by the high-level software. Thededicated programming tools support multitasking property of the microcontroller by selectionof different sampling frequencies of algorithm blocks. In this case the multi-layer andmultitasking control strategy can be realized on the chip. The proposed solutions implementrapid prototyping approach. The available toolkits and device drivers integrate system-leveldesign environment and the real-time application software, transferring the functionality ofMATLAB/Simulink programs to PCs or microcontrolers application environment.

The LBT real-time based control software to mitigate and compensate vibrations

Science.gov (United States)

Borelli, J.; Trowitzsch, J.; Brix, M.; Kürster, M.; Gässler, W.; Bertram, T.; Briegel, F.

2010-07-01

The Large Binocular Telescope (LBT) uses two 8.4 meters active primary mirrors and two adaptive secondary mirrors on the same mounting to take advantage of its interferometric capabilities. Both applications, interferometry and AO, are sensitive to vibrations. Several measurement campaigns have been carried out at the LBT and their results strongly indicate that a vibration monitoring system is required to improve the performance of LINC-NIRVANA, LBTI, and ARGOS, the laser guided ground layer adaptive optic system. Currently, a control software for mitigation and compensation of the vibrations is being designed. A complex set of algorithms collects real-time vibration data, archiving it for further analysis, and in parallel, generating the tip-tilt and optical path difference (OPD) data for the control loop of the instruments. A real-time data acquisition device equipped with embedded real-time Linux is used in our systems. A set of quick-look tools is currently under development in order to verify if the conditions at the telescope are suitable for interferometric/adaptive observations.

Round table discussion: Quality control and standardization of nuclear medicine software

International Nuclear Information System (INIS)

Anon.

1988-01-01

In summary the round table came to the following important conclusions: Nuclear medicine software systems need better documentation, especially regarding details of algorithms and limitations, and user friendliness could be considerably improved. Quality control of software is an integral part of quality assurance in nuclear medicine and should be performed at all levels of the software. Quality control of applications software should preferably be performed with assistance of generally accepted software phantoms. A basic form of standardization was welcomed and partly regarded as essential by all participants. Some areas such as patient study files could be standardized in the near future, whereas other areas such as the standardization of clinical applications programs or acquisition protocols still present major difficulties. An international cooperation in the field of standardization of software and other topics has already been started on the European level and should be continued and supported. (orig.)

Real-time solar magnetograph operation system software design and user's guide

Science.gov (United States)

Wang, C.

1984-01-01

The Real Time Solar Magnetograph (RTSM) Operation system software design on PDP11/23+ is presented along with the User's Guide. The RTSM operation software is for real time instrumentation control, data collection and data management. The data is used for vector analysis, plotting or graphics display. The processed data is then easily compared with solar data from other sources, such as the Solar Maximum Mission (SMM).

Bayesian Software Health Management for Aircraft Guidance, Navigation, and Control

Science.gov (United States)

Schumann, Johann; Mbaya, Timmy; Menghoel, Ole

2011-01-01

Modern aircraft, both piloted fly-by-wire commercial aircraft as well as UAVs, more and more depend on highly complex safety critical software systems with many sensors and computer-controlled actuators. Despite careful design and V&V of the software, severe incidents have happened due to malfunctioning software. In this paper, we discuss the use of Bayesian networks (BNs) to monitor the health of the on-board software and sensor system, and to perform advanced on-board diagnostic reasoning. We will focus on the approach to develop reliable and robust health models for the combined software and sensor systems.

The Los Alamos accelerator control system data base: A generic instrumentation interface

International Nuclear Information System (INIS)

Dalesio, L.R.

1990-01-01

Controlling experimental-physics applications requires a control system that can be quickly integrated and easily modified. One aspect of the control system is the interface to the instrumentation. An instrumentation set has been chosen to implement the basic functions needed to monitor and control these applications. A data-driven interface to this instrumentation set provides the required quick integration of the control system. This type of interface is limited by its built-in capabilities. Therefore, these capabilities must provide an adequate range of functions to be of any use. The data-driven interface must support the instrumentation range requird, the events on which to read or control the instrumentation and a method for manipulating the data to calculate terms or close control loops. The database for the Los Alamos Accelerator Control System addresses these requirements. (orig.)

Control software development for magnetorheological finishing of large aperture optical elements

International Nuclear Information System (INIS)

Zheng Nan; Li Haibo; Yuan Zhigang; Zhong Bo

2011-01-01

Based on the mechanism of magnetorheological finishing, the dwell time function was solved by Jansson-Van Cit-tert algorithm to accomplish the kernel module design. Then the software modularization programming, modular testing and integration testing were conducted. A verification experiment was carried out on a crystal element with full aperture of 500 mm and the element's surface achieved rapid and efficient convergence after the software controlled magnetorheological finishing. It is proved that the software could control the whole polishing process accurately. (authors)

Software design of a general purpose data acquisition and control executive

International Nuclear Information System (INIS)

Labiak, W.G.; Minor, E.G.

1981-01-01

The software design of an executive which performs general purpose data acquisition, monitoring, and control is presented. The executive runs on a memory-based mini or micro-computer and communicates with a disk-based computer where data analysis and display are done. The executive design stresses reliability and versatility, and has yielded software which can provide control and monitoring for widely different hardware systems. Applications of this software on two major fusion energy experiments at Lawrence Livermore National Laboratory will be described