Gamma scanning of large sieve tray towers

International Nuclear Information System (INIS)

McCaw, D.D.; Hulbert, V.G.; Smith, A.E.

1976-01-01

A special instrument based on the use of gamma rays, has been developed, which assists in the evaluation of the effects of changes in controlled variables on sieve tray performance. Internal structural damage, and local tray flooding are readily detectable from outside the vessel. The instrument is described, and examples of its use are given. (author)

Heat and Mass Transfer Measurements for Tray-Fermented Fungal Products

Science.gov (United States)

Jou, R.-Y.; Lo, C.-T.

2011-01-01

In this study, heat and mass transfer in static tray fermentation, which is widely used in solid-state fermentation (SSF) to produce fungal products, such as enzymes or koji, is investigated. Specifically, kinetic models of transport phenomena in the whole-tray chamber are emphasized. The effects of temperature, moisture, and humidity on microbial growth in large-scale static tray fermentation are essential to scale-up SSF and achieve uniform fermentation. In addition, heat and mass transfer of static tray fermentation of Trichoderma fungi with two tray setups—traditional linen coverings and stacks in a temperature-humidity chamber is examined. In both these setups, the following factors of fermentation were measured: air velocity, air temperature, illumination, pH, carbon dioxide (CO2) concentration, and substrate temperature, and the effects of bed height, moisture of substrate, and relative humidity of air are studied. A thin (1 cm) bed at 28 °C and 95 % relative humidity is found to be optimum. Furthermore, mixing was essential for achieving uniform fermentation of Trichoderma fungi. This study has important applications in large-scale static tray fermentation of fungi.

Three-input gate logic circuits on chemically assembled single-electron transistors with organic and inorganic hybrid passivation layers.

Science.gov (United States)

Majima, Yutaka; Hackenberger, Guillaume; Azuma, Yasuo; Kano, Shinya; Matsuzaki, Kosuke; Susaki, Tomofumi; Sakamoto, Masanori; Teranishi, Toshiharu

2017-01-01

Single-electron transistors (SETs) are sub-10-nm scale electronic devices based on conductive Coulomb islands sandwiched between double-barrier tunneling barriers. Chemically assembled SETs with alkanethiol-protected Au nanoparticles show highly stable Coulomb diamonds and two-input logic operations. The combination of bottom-up and top-down processes used to form the passivation layer is vital for realizing multi-gate chemically assembled SET circuits, as this combination enables us to connect conventional complementary metal oxide semiconductor (CMOS) technologies via planar processes. Here, three-input gate exclusive-OR (XOR) logic operations are demonstrated in passivated chemically assembled SETs. The passivation layer is a hybrid bilayer of self-assembled monolayers (SAMs) and pulsed laser deposited (PLD) aluminum oxide (AlO[Formula: see text]), and top-gate electrodes were prepared on the hybrid passivation layers. Top and two-side-gated SETs showed clear Coulomb oscillation and diamonds for each of the three available gates, and three-input gate XOR logic operation was clearly demonstrated. These results show the potential of chemically assembled SETs to work as logic devices with multi-gate inputs using organic and inorganic hybrid passivation layers.

Accuracy of a separating foil impression using a novel polyolefin foil compared to a custom tray and a stock tray technique

Science.gov (United States)

Pastoret, Marie-Hélène; Bühler, Julia; Weiger, Roland

2017-01-01

PURPOSE To compare the dimensional accuracy of three impression techniques- a separating foil impression, a custom tray impression, and a stock tray impression. MATERIALS AND METHODS A machined mandibular complete-arch metal model with special modifications served as a master cast. Three different impression techniques (n = 6 in each group) were performed with addition-cured silicon materials: i) putty-wash technique with a prefabricated metal tray (MET) using putty and regular body, ii) single-phase impression with custom tray (CUS) using regular body material, and iii) two-stage technique with stock metal tray (SEP) using putty with a separating foil and regular body material. All impressions were poured with epoxy resin. Six different distances (four intra-abutment and two inter-abutment distances) were gauged on the metal master model and on the casts with a microscope in combination with calibrated measuring software. The differences of the evaluated distances between the reference and the three test groups were calculated and expressed as mean (± SD). Additionally, the 95% confidence intervals were calculated and significant differences between the experimental groups were assumed when confidence intervals did not overlap. RESULTS Dimensional changes compared to reference values varied between -74.01 and 32.57 µm (MET), -78.86 and 30.84 (CUS), and between -92.20 and 30.98 (SEP). For the intra-abutment distances, no significant differences among the experimental groups were detected. CUS showed a significantly higher dimensional accuracy for the inter-abutment distances with -0.02 and -0.08 percentage deviation compared to MET and SEP. CONCLUSION The separation foil technique is a simple alternative to the custom tray technique for single tooth restorations, while limitations may exist for extended restorations with multiple abutment teeth. PMID:28874996

Accuracy of a self-perforating impression tray for dental implants.

Science.gov (United States)

Marotti, Juliana; Tortamano, Pedro; Castilho, Tatiana R R N; Steagall, Washington; Wolfart, Stefan; Haselhuhn, Klaus

2014-10-01

Difficulties are involved in impression making with conventional open impression trays. The purpose of this study was to evaluate the accuracy of transferring implant impressions with a self-perforating impression tray. A reference model of a mandible was fabricated, and 4 implants were placed in the regions of the first premolars and lateral incisors (implants 1, 2, 3, 4). Ten impressions of the reference model with polyvinyl siloxane were made for each group; control (conventional open impression tray) and test (self-perforating impression tray; Miratray Implant). A metal bar was screw-retained on implant 1, and the gaps generated at the vestibular face of implants 3 and 4 were measured by optical microcopy. The 2-way ANOVA and least square difference post hoc test were used (α=.05). Higher mean (±SD) values were obtained for the test group than for the control group for both implants: implant 3: 150 ±84 μm for the test group, 73 ±63 μm for the control group (P=.019); implant 4: 129 ±65 μm for the test group, 62 ±61 μm for the control group (P=.04). The self-perforating impression tray provided less accuracy than the conventional open tray. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Applications of T-ray spectroscopy in the petroleum field

Science.gov (United States)

Al-Douseri, Fatemah M.

2005-11-01

Because of heavy usage of petroleum products, which are the main source of energy in daily life and industry, a fast, reliable, and portable analysis system is needed to complement traditional techniques. Terahertz (THz) radiation, or T-rays, is electromagnetic radiation in the 0.1 to 10 THz frequency range. One unique attribute of T-rays is their ability to sensitively measure the induced molecular dipole moments in non-polar liquids such as aromatics, which make up the majority of the contents of many petroleum products. This information can lead to several applications in petroleum analysis. The application of T-rays to petroleum product analysis has the potential to make a significant impact in the petroleum field. In this dissertation, I show the first use of T-ray time-domain spectroscopy and Fourier transform infrared (FTIR) spectroscopy techniques for petroleum product analysis. I report on the feasibility of analyzing selected petroleum products, including gasoline, diesel, lubricating oil, and selected compounds of toluene, ethylbenzene, and xylene (BTEX). With the use of a T-ray time-domain spectrometer. I demonstrate that gasolines with different octane numbers and diesel all show specific absorption coefficients and refractive indexes in the spectral range from 0.5 to 2.0 THz. Furthermore, I report the qualitative and quantitative analysis of selected BTEX components in gasoline and diesel using FTIR spectroscopy in the 50 to 650 cm-1 region. I distinguish gasolines with different octane numbers from diesel and lubricating oil according to their different spectral features. I also determine the concentration of (o, m, p) xylene isomers in gasoline according to their specific absorption bands. The experimental results in this thesis, imply that linking between the knowledge of petroleum products and the development of T-ray spectrometer with the cooperation of industry might translate the T-ray spectroscopic system into a real world application in

Cable tray ultimate strength test employing a large shaker table

Energy Technology Data Exchange (ETDEWEB)

Komatsu, K.; Myojin, K.; Imai, K. [The Kansai Electric Power Co., Osaka (Japan); Fuyama, H. [Mitsubishi Heavy Industries Ltd, Takasago (Japan); Kokubo, E. [Mitsubishi Heavy Industdries Ltd, Kobe (Japan)

2004-07-01

Ultimate behaviors of cable trays, used in nuclear plants, have not been well studied since cable trays are designed based on conservative design criteria. In this study, by employing a large shaker table, an ultimate strength test was conducted for cable trays used in nuclear power plants. This report describes the results of shaker table test. The following results were obtained. First, in an S{sub 2} earthquake, the damping ratio was so large - more than 30% due to the rubbing of cables - that a large response was not present and the strains in the support were within the elastic limits. Secondly, the support was strong enough to sustain the cable trays even when the strain in the support was 20 times larger than the elastic limit. (authors)

Image Processing Techniques for Assessment of Dental Trays

Science.gov (United States)

2001-10-25

170 patients having Angle Class I molar relationships with minor malocclusions and teeth including second molars fully erupted without loss of tooth...Abstract-A tray selected for the dental patient must adapt to the curvature of the teeth and allow the impression material to be in appropriate...brands of perforated metal trays with 170 lower arch cast models collected from patients having Angle Class 1 type occlusion with minor malocclusions

Report on full-scale horizontal cable tray fire tests, FY 1988

International Nuclear Information System (INIS)

Riches, W.M.

1988-09-01

In recent years, there has been much discussion throughout industry and various governmental and fire protection agencies relative to the flammability and fire propagation characteristics of electrical cables in open cable trays. It has been acknowledged that under actual fire conditions, in the presence of other combustibles, electrical cable insulation can contribute to combustible fire loading and toxicity of smoke generation. Considerable research has been conducted on vertical cable tray fire propagation, mostly under small scale laboratory conditions. In July 1987, the Fermi National Accelerator Laboratory initiated a program of full scale, horizontal cable tray fire tests, in the absence of other building combustible loading, to determine the flammability and rate of horizontal fire propagation in cable tray configurations and cable mixes typical of those existing in underground tunnel enclosures and support buildings at the Laboratory. The series of tests addressed the effects of ventilation rates and cable tray fill, fire fighting techniques, and effectiveness and value of automatic sprinklers, smoke detection and cable coating fire barriers in detecting, controlling or extinguishing a cable tray fire. This report includes a description of the series of fire tests completed in June 1988, as well as conclusions reached from the test results

Application of FDM three-dimensional printing technology in the digital manufacture of custom edentulous mandible trays

Science.gov (United States)

Chen, Hu; Yang, Xu; Chen, Litong; Wang, Yong; Sun, Yuchun

2016-01-01

The objective was to establish and evaluate a method for manufacture of custom trays for edentulous jaws using computer aided design and fused deposition modeling (FDM) technologies. A digital method for design the custom trays for edentulous jaws was established. The tissue surface data of ten standard mandibular edentulous plaster models, which was used to design the digital custom tray in a reverse engineering software, were obtained using a 3D scanner. The designed tray was printed by a 3D FDM printing device. Another ten hand-made custom trays were produced as control. The 3-dimentional surface data of models and custom trays was scanned to evaluate the accuracy of reserved impression space, while the difference between digitally made trays and hand-made trays were analyzed. The digitally made custom trays achieved a good matching with the mandibular model, showing higher accuracy than the hand-made ones. There was no significant difference of the reserved space between different models and its matched digitally made trays. With 3D scanning, CAD and FDM technology, an efficient method of custom tray production was established, which achieved a high reproducibility and accuracy. PMID:26763620

Integrated CFD investigation of heat transfer enhancement using multi-tray core catcher in SFR

International Nuclear Information System (INIS)

Rakhi; Sharma, Anil Kumar; Velusamy, K.

2017-01-01

Highlights: • Heat transfer enhancement using multi-tray core catcher for SFR is investigated. • The capability of a single core collector tray is estimated. • Double and triple collector trays with innovative designs is discussed. • Provision of openings in the trays contributed to enhanced natural circulation. - Abstract: To render future SFR more robust and safe, certain BDBE have been considered in the recent years. A Core Disruptive Accident leading to a whole core meltdown scenario has gained the interest of researchers. Various design concepts and safety measures have been suggested and incorporated in design to address such a low probability scenario. A core catcher concept, in particular, has proved to be inevitable as an in-vessel core retention device in SFR for safe retention of core debris arising out after the severe accident. This study aims to analyse the cooling capability of the innovative design concept of core catcher to remove decay heat of degraded core after the accident. First, the capability of single collection tray is established and then the study is extended to two and three collection trays with different design concepts. Transient forms of governing equations of mass, momentum and energy conservations along with k-ε turbulence model are solved by finite volume based CFD solver. Boussinesq approximation is invoked to model buoyancy in sodium. The study shows that a single collection tray is capable of removing up to 20 MW decay heat load in a typical 500 MWe pool type SFR. Further, studies are carried out to improve the natural circulation of sodium around the source, in the lower plenum and to distribute core debris of the whole core to multiple collection trays. It is found that the double and triple collection trays can accommodate decay loads up to 29 MW. Provision of openings in the collection trays has proved to be effective in improving the heat transfer and sodium flow as well as in distributing the core debris to the

Input dependent cell assembly dynamics in a model of the striatal medium spiny neuron network

Directory of Open Access Journals (Sweden)

Adam ePonzi

2012-03-01

Full Text Available The striatal medium spiny neuron (MSNs network is sparsely connected with fairly weak GABAergic collaterals receiving an excitatory glutamatergic cortical projection. Peri stimulus time histograms (PSTH of MSN population response investigated in various experimental studies display strong firing rate modulations distributed throughout behavioural task epochs. In previous work we have shown by numerical simulation that sparse random networks of inhibitory spiking neurons with characteristics appropriate for UP state MSNs form cell assemblies which fire together coherently in sequences on long behaviourally relevant timescales when the network receives a fixed pattern of constant input excitation. Here we first extend that model to the case where cortical excitation is composed of many independent noisy Poisson processes and demonstrate that cell assembly dynamics is still observed when the input is sufficiently weak. However if cortical excitation strength is increased more regularly firing and completely quiescent cells are found, which depend on the cortical stimulation. Subsequently we further extend previous work to consider what happens when the excitatory input varies as it would in when the animal is engaged in behavior. We investigate how sudden switches in excitation interact with network generated patterned activity. We show that sequences of cell assembly activations can be locked to the excitatory input sequence and delineate the range of parameters where this behaviour is shown. Model cell population PSTH display both stimulus and temporal specificity, with large population firing rate modulations locked to elapsed time from task events. Thus the random network can generate a large diversity of temporally evolving stimulus dependent responses even though the input is fixed between switches. We suggest the MSN network is well suited to the generation of such slow coherent task dependent response

Input dependent cell assembly dynamics in a model of the striatal medium spiny neuron network.

Science.gov (United States)

Ponzi, Adam; Wickens, Jeff

2012-01-01

The striatal medium spiny neuron (MSN) network is sparsely connected with fairly weak GABAergic collaterals receiving an excitatory glutamatergic cortical projection. Peri-stimulus time histograms (PSTH) of MSN population response investigated in various experimental studies display strong firing rate modulations distributed throughout behavioral task epochs. In previous work we have shown by numerical simulation that sparse random networks of inhibitory spiking neurons with characteristics appropriate for UP state MSNs form cell assemblies which fire together coherently in sequences on long behaviorally relevant timescales when the network receives a fixed pattern of constant input excitation. Here we first extend that model to the case where cortical excitation is composed of many independent noisy Poisson processes and demonstrate that cell assembly dynamics is still observed when the input is sufficiently weak. However if cortical excitation strength is increased more regularly firing and completely quiescent cells are found, which depend on the cortical stimulation. Subsequently we further extend previous work to consider what happens when the excitatory input varies as it would when the animal is engaged in behavior. We investigate how sudden switches in excitation interact with network generated patterned activity. We show that sequences of cell assembly activations can be locked to the excitatory input sequence and outline the range of parameters where this behavior is shown. Model cell population PSTH display both stimulus and temporal specificity, with large population firing rate modulations locked to elapsed time from task events. Thus the random network can generate a large diversity of temporally evolving stimulus dependent responses even though the input is fixed between switches. We suggest the MSN network is well suited to the generation of such slow coherent task dependent response which could be utilized by the animal in behavior.

A distillation tray with high efficiency and excellent operating flexibility for viscous mixture separation

Directory of Open Access Journals (Sweden)

Li Qunsheng

2014-01-01

Full Text Available The flow-guided sieve-valve tray(FGS-VTwith high efficiency was designed to overcome the shortcoming of low operating flexibility of the flow-guided sieve tray. Its dimensions and geometry, as well as structure characteristics, were presented. The hydrodynamics and mass transfer performance, including dry-plate pressure drop, wet plate-pressure drop, weeping, entrainment and tray efficiency, of two types of FGS-VTs (FGS-VTs with 14 and 8 valves, respectively and one flow-guided sieve tray were tested in an air-water-oxygen cold model experiment with a 0.6 m diameter plexiglass column. The results demonstrate that FGS-VT with 14 valves works better than FGS-VT with 8 valves, and in comparison with the flow-guided sieve tray, the flow-guided sieve-valve tray with 14 valves has higher tray efficiency, bigger operating flexibility, and lower wet-plate pressure drop (when all the valves are opened fully.Additionally, two typical applications to separate the mixture with high viscosity, solid, powder, easy-to-foam or easy self-polymerization components proved the unique advantages of FGS-VT.

Effects of surface tension on tray point efficiencies

Energy Technology Data Exchange (ETDEWEB)

Chen, G.X.; Afacan, A.; Chuang, K.T. (Alberta Univ., Edmonton, AB (Canada))

1994-08-01

Sieve tray efficiencies for the distillation of methanol/water, acetic acid/water, and cyclohexane/n-heptane mixtures were measured as a function of composition under fixed vapor and liquid rates in a 0.15 m diameter distillation column. The three binary distillation systems used in the study had a wide range of surface tensions measured as a function of composition. From the efficiencies measured, the number of vapor- and liquid-phase transfer units (Ng and Nl) was determined and the effects of surface tension on Ng and Nl were identified. To further verify the results obtained from the distillation column, bubble sizes in froths for air/water, air/methanol, and air/(water + surfactant) systems with different surface tensions were measured. The results show that surface tension has a significant effect on tray efficiency and the number of transfer units. Bubble sizes in the tray froths were mainly determined by surface tension, and bubble breakup and coalescence occur in the froths. 45 refs., 15 figs., 1 tab.

An enhanced fire hazard assessment model and validation experiments for vertical cable trays

International Nuclear Information System (INIS)

Li, Lu; Huang, Xianjia; Bi, Kun; Liu, Xiaoshuang

2016-01-01

Highlights: • An enhanced model was developed for vertical cable fire hazard assessment in NPP. • The validated experiments on vertical cable tray fires were conducted. • The capability of the model for cable tray with different cable spacing were tested. - Abstract: The model, referred to as FLASH-CAT (Flame Spread over Horizontal Cable Trays), was developed to estimate the heat release rate for vertical cable tray fire. The focus of this work is to investigate the application of an enhanced model to the single vertical cable tray fires with different cable spacing. The experiments on vertical cable tray fires with three typical cable spacing were conducted. The histories of mass loss rate and flame length were recorded during the cable fire. From the experimental results, it is found that the space between cable lines intensifies the cable combustion and accelerates the flame spread. The predictions by the enhanced model show good agreements with the experimental data. At the same time, it is shown that the enhanced model is capable of predicting the different behaviors of cable fires with different cable spacing by adjusting the flame spread speed only.

An enhanced fire hazard assessment model and validation experiments for vertical cable trays

Energy Technology Data Exchange (ETDEWEB)

Li, Lu [Sate Key Laboratory of Fire Science, University of Science and Technology of China, Hefei 230027 (China); Huang, Xianjia, E-mail: huangxianjia@gziit.ac.cn [Joint Laboratory of Fire Safety in Nuclear Power Plants, Institute of Industry Technology Guangzhou & Chinese Academy of Sciences, Guangzhou 511458 (China); Bi, Kun; Liu, Xiaoshuang [China Nuclear Power Design Co., Ltd., Shenzhen 518045 (China)

2016-05-15

Highlights: • An enhanced model was developed for vertical cable fire hazard assessment in NPP. • The validated experiments on vertical cable tray fires were conducted. • The capability of the model for cable tray with different cable spacing were tested. - Abstract: The model, referred to as FLASH-CAT (Flame Spread over Horizontal Cable Trays), was developed to estimate the heat release rate for vertical cable tray fire. The focus of this work is to investigate the application of an enhanced model to the single vertical cable tray fires with different cable spacing. The experiments on vertical cable tray fires with three typical cable spacing were conducted. The histories of mass loss rate and flame length were recorded during the cable fire. From the experimental results, it is found that the space between cable lines intensifies the cable combustion and accelerates the flame spread. The predictions by the enhanced model show good agreements with the experimental data. At the same time, it is shown that the enhanced model is capable of predicting the different behaviors of cable fires with different cable spacing by adjusting the flame spread speed only.

Biodegradable foam trays obtained from mixtures of non-irradiated and irradiated cassava starches

International Nuclear Information System (INIS)

Brant, A.J.C.; Naime, N.; Lugao, A.B.; Ponce, P.

2015-01-01

Biodegradable polymers, such as starch, cellulose, PHB, PLA, and derivatives thereof, are being studied to produce innovative packaging in the most diverse shapes (films, bags, trays, bottles, etc.) to attend this current market trend. The aim of this work was to produce foam trays from cassava starch for food packaging by extrusion-thermopressing process. Their formulations were based on non-irradiated and γ-irradiated starches at diverse radiation absorbed doses (kGy) in order to evaluate the influence of the irradiated starches on the physical properties of the trays. Water absorption results showed an irregular increase with the increase of the absorbed dose: 26.32% and 39.84% for the trays based on starch 0 kGy and 1:1 (w/w) mixture of starches 0 kGy and 100.0 kGy, respectively. Other physicochemical properties were evaluated from the starches utilized and the trays obtained. (author)

Biodegradable foam trays obtained from mixtures of non-irradiated and irradiated cassava starches

Energy Technology Data Exchange (ETDEWEB)

Brant, A.J.C.; Naime, N.; Lugao, A.B.; Ponce, P., E-mail: thonybrant@gmail.com, E-mail: patiponce@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

Biodegradable polymers, such as starch, cellulose, PHB, PLA, and derivatives thereof, are being studied to produce innovative packaging in the most diverse shapes (films, bags, trays, bottles, etc.) to attend this current market trend. The aim of this work was to produce foam trays from cassava starch for food packaging by extrusion-thermopressing process. Their formulations were based on non-irradiated and γ-irradiated starches at diverse radiation absorbed doses (kGy) in order to evaluate the influence of the irradiated starches on the physical properties of the trays. Water absorption results showed an irregular increase with the increase of the absorbed dose: 26.32% and 39.84% for the trays based on starch 0 kGy and 1:1 (w/w) mixture of starches 0 kGy and 100.0 kGy, respectively. Other physicochemical properties were evaluated from the starches utilized and the trays obtained. (author)

Polylactic acid trays for fresh-food packaging: A Carbon Footprint assessment.

Science.gov (United States)

Ingrao, Carlo; Tricase, Caterina; Cholewa-Wójcik, Agnieszka; Kawecka, Agnieszka; Rana, Roberto; Siracusa, Valentina

2015-12-15

This paper discusses application of Carbon Footprint (CF) for quantification of the 100-year Global Warming Potential (GWP100) associated with the life cycle of polylactic acid (PLA) trays for packaging of fresh foods. A comparison with polystyrene (PS)-based trays was done considering two different transport system scenarios for PLA-granule supply to the tray production firm: a transoceanic freight vessel and an intercontinental freight aircraft. Doing so enabled estimation of the influence of the transportation phase on the GHG-emission rate associated with the PLA-trays' life cycle. From the assessment, the GWP100 resulted to be mainly due to PLA-granulate production and to its transportation to the tray manufacturing facility. Also, the study documented that, depending upon the transport system considered, the CF associated with the life cycle of the PLA trays can worsen so much that the latter are no longer GHG-emission saving as they are expected to be compared to the PS ones. Therefore, based upon the findings of the study, it was possible for the authors to understand the importance and the need of accounting for the transport-related issues in the design of PLA-based products, thus preserving their environmental soundness compared to traditional petroleum-based products. In this context, the study could be used as the base to reconsider the merits of PLA usage for product manufacturing, especially when high distances are implied, as in this analysed case. So, the authors believe that new research and policy frameworks should be designed and implemented for both development and promotion of more globally sustainable options. Copyright © 2015 Elsevier B.V. All rights reserved.

[Application of individual light-curing resin tray as edge plastic material in complete denture modulo].

Science.gov (United States)

Chai, Mei; Tang, Xuyan; Liang, Guangku

2015-12-01

To investigate clinical effect of individual light-curing resin tray as edge plastic material in complete denture modulo.
 A total of 30 patients with poor condition for alveolar ridge of mandible were chosen individual tray with individual light-curing resin tray for material edge shaping or traditional individual impression tray for edge shaping cream to produce complete denture. The operability, questionnaire about denture retention, comfort, mucosal cases and chewing function in the process of shaping the edge were investigated three months later after wearing dentures.
 There was no significant difference in retention, comfort, mucosa and the chewing function between the two mandibular denture impression methods. However, the patients with individual light-curing resin tray as edge shaping material felt better in the process than that in the patients with die-cream as the edge shaping material (P<0.05). Furthermore, the manipulation with individual light-curing resin tray as edge shaping material is easy for doctor.
 Although the clinical effect of Individual light-curing resin tray material as the edge shaping material is equal to that of impression cream, it saves time and human resource. Moreover, it is more acceptable for the patients and thus it can be spread in clinics.

Vibration isolation of cable tray hangers

International Nuclear Information System (INIS)

Pearce, B.K.; Dixon, M.W.; Jackson, J.E.

1984-01-01

Analytical and experimental investigations have been performed to partially evaluate the feasibility of using much more flexible support systems than those presently used to support electrical and control cables in nuclear power plants. This approach, which entails introducing a flexible element between the support and the component being supported, could apply to many types of support systems, such as for piping, HVAC or even bridges. However, this paper addresses the specific case of cable tray hangers only. It was found that, for appropriate stiffness and damping characteristics, this concept could be used effectively to isolate cable trays from hanger motion caused by seismic excitation and to significantly reduce hanger loads while maintaining reasonable displacements. This was found to be true for all variations in system parameters investigated. Thus, the flexible hanger concept appears to offer much potential. However, additional study including full-scale testing and more detailed analysis must be completed before the concept can be validated for plant use

Novel method of fabricating individual trays for maxillectomy patients by computer-aided design and rapid prototyping.

Science.gov (United States)

Huang, Zhi; Wang, Xin-zhi; Hou, Yue-Zhong

2015-02-01

Making impressions for maxillectomy patients is an essential but difficult task. This study developed a novel method to fabricate individual trays by computer-aided design (CAD) and rapid prototyping (RP) to simplify the process and enhance patient safety. Five unilateral maxillectomy patients were recruited for this study. For each patient, a computed tomography (CT) scan was taken. Based on the 3D surface reconstruction of the target area, an individual tray was manufactured by CAD/RP. With a conventional custom tray as control, two final impressions were made using the different types of tray for each patient. The trays were sectioned, and in each section the thickness of the material was measured at six evenly distributed points. Descriptive statistics and paired t-test were used to examine the difference of the impression thickness. SAS 9.3 was applied in the statistical analysis. Afterwards, all casts were then optically 3D scanned and compared digitally to evaluate the feasibility of this method. Impressions of all five maxillectomy patients were successfully made with individual trays fabricated by CAD/RP and traditional trays. The descriptive statistics of impression thickness measurement showed slightly more uneven results in the traditional trays, but no statistical significance was shown. A 3D digital comparison showed acceptable discrepancies within 1 mm in the majority of cast areas. The largest difference of 3 mm was observed in the buccal wall of the defective areas. Moderate deviations of 1 to 2 mm were detected in the buccal and labial vestibular groove areas. This study confirmed the feasibility of a novel method of fabricating individual trays by CAD/RP. Impressions made by individual trays manufactured using CAD/RP had a uniform thickness, with an acceptable level of accuracy compared to those made through conventional processes. © 2014 by the American College of Prosthodontists.

Electrical Programming of Soft Matter: Using Temporally Varying Electrical Inputs To Spatially Control Self Assembly.

Science.gov (United States)

Yan, Kun; Liu, Yi; Zhang, Jitao; Correa, Santiago O; Shang, Wu; Tsai, Cheng-Chieh; Bentley, William E; Shen, Jana; Scarcelli, Giuliano; Raub, Christopher B; Shi, Xiao-Wen; Payne, Gregory F

2018-02-12

The growing importance of hydrogels in translational medicine has stimulated the development of top-down fabrication methods, yet often these methods lack the capabilities to generate the complex matrix architectures observed in biology. Here we show that temporally varying electrical signals can cue a self-assembling polysaccharide to controllably form a hydrogel with complex internal patterns. Evidence from theory and experiment indicate that internal structure emerges through a subtle interplay between the electrical current that triggers self-assembly and the electrical potential (or electric field) that recruits and appears to orient the polysaccharide chains at the growing gel front. These studies demonstrate that short sequences (minutes) of low-power (∼1 V) electrical inputs can provide the program to guide self-assembly that yields hydrogels with stable, complex, and spatially varying structure and properties.

On seismic design of cable trays and their supports

International Nuclear Information System (INIS)

Hartmann, B.

1978-01-01

Codes presently in force for design of nuclear power plants require seismic qualification for all electric equipment. In the case of cable trays and their supports one usually attempts to meet the requirements of the code by stiffening a standardized design. This procedure leads to impracticall,imensions for the mountings and, above all, to the loss of the modular character. With strong earthquakes however, it may become irrational at all. This paper suggests an alternate strategy. It starts with a standardized system again, adding some units. These are on the one hand diagonal bracing elements, arbitrarily to arrange, thus gaining a more or less rigid supporting framework. And on the other hand as an essential modification, elastomer rubber pads are inserted as spring bearings. With these pads between the supporting and the adjoining structure, the assembly becomes tractable with respect to earthquake qualification. The question of material properties is also addressed. The elastomer pads have to be chosen so as to fulfil all expected functions under usual as well as extreme environmental conditions. (Author)

Tropical field performance of dual-pass PV tray dryer

Science.gov (United States)

Iskandar, A. Noor; Ya'acob, M. E.; Anuar, M. S.

2017-09-01

Solar Photovoltaic technology has become the preferable solution in many countries around the globe to solve the ever increasing energy demand of the consumers. In line with the consumer need, food processing technology has huge potentials of integration with the renewable energy resources especially in drying process which consumes the highest electricity loads. Traditionally, the solar dryer technology was applied in agriculture and food industries utilizing the sun's energy for drying process, but this is highly dependable on the weather condition and surrounding factors. This work shares some field performance of the new design of portable dual-pass PV tray dryer for drying crops in an enclosed system. The dual-pass PV tray dryer encompass a lightweight aluminium box structure with dimensions of 1.1m (L) x 0.6m (W) x 0.2m (H) and can hold a load capacity of 300g - 3kg of crop depending on the types of the crops. Experiments of field performance monitoring were conducted in October -November 2016 which justifies a considerable reduction in time and crops quality improvement when using the dual-pass PV tray dryer as compared to direct-sun drying.

[Evaluation of production and clinical working time of computer-aided design/computer-aided manufacturing (CAD/CAM) custom trays for complete denture].

Science.gov (United States)

Wei, L; Chen, H; Zhou, Y S; Sun, Y C; Pan, S X

2017-02-18

To compare the technician fabrication time and clinical working time of custom trays fabricated using two different methods, the three-dimensional printing custom trays and the conventional custom trays, and to prove the feasibility of the computer-aided design/computer-aided manufacturing (CAD/CAM) custom trays in clinical use from the perspective of clinical time cost. Twenty edentulous patients were recruited into this study, which was prospective, single blind, randomized self-control clinical trials. Two custom trays were fabricated for each participant. One of the custom trays was fabricated using functional suitable denture (FSD) system through CAD/CAM process, and the other was manually fabricated using conventional methods. Then the final impressions were taken using both the custom trays, followed by utilizing the final impression to fabricate complete dentures respectively. The technician production time of the custom trays and the clinical working time of taking the final impression was recorded. The average time spent on fabricating the three-dimensional printing custom trays using FSD system and fabricating the conventional custom trays manually were (28.6±2.9) min and (31.1±5.7) min, respectively. The average time spent on making the final impression with the three-dimensional printing custom trays using FSD system and the conventional custom trays fabricated manually were (23.4±11.5) min and (25.4±13.0) min, respectively. There was significant difference in the technician fabrication time and the clinical working time between the three-dimensional printing custom trays using FSD system and the conventional custom trays fabricated manually (Pmanufacture custom trays by three-dimensional printing method, there is no need to pour preliminary cast after taking the primary impression, therefore, it can save the impression material and model material. As to completing denture restoration, manufacturing custom trays using FSD system is worth being

Image Processing Techniques for Assessment of Dental Trays

National Research Council Canada - National Science Library

Yergin, E

2001-01-01

.... This technique was used for the alignment of six brands of perforated metal trays with 170 lower arch cast models collected from patients having Angle Class 1 type occlusion with minor malocclusions...

Design and Production of Damage-Resistant Tray Pack Containers

Science.gov (United States)

1985-07-01

No COMMENT ,34.5 ýX .7.. . , . 35.0 x 36.0 x " 36.5 x • - . ,- 37.0 x 37.5 X 22 Ma after failure .4 J L,. Local Red stain...VACUUM-TRAY PACK SAMPLE 90#-BASELINE !4 TEST LEVEL PANEL VACUUM YES NO COMMENT 𔃾 I S2"X - 3" X 4ŕ x 4.5" X 27 Ma with Red spot @ S1 - wrinkle. * i...44 i 63 DATE 8-29-84 * SAMPLE # 3 TEST TYPE VACUUM-TRAY PACK SAMPLE 90#/0.050" REINFORCED TEST LEVEL PAN] VACUUM YES NO COMMENT i ", 2" X 2 1 V - I

Effects of impression levels and trays on the accuracy of impressions taken from angulated implants.

Science.gov (United States)

Geramipanah, Farideh; Sahebi, Majid; Davari, Maryam; Hajimahmoudi, Mohammadreza; Rakhshan, Vahid

2015-09-01

It is crucial to keep the misfit of the abutment-fixture unit at the lowest possible rate. There are a few controversial studies on the accuracy of impression making of angulated implants, and much fewer (and controversial) studies on the abutment-level impression technique, which is a convenient and clinically favorable method. Besides, there are no studies on comparison of sectional vs. full-arch trays. We aimed to assess these. A trapezoidal model with four angulated implants installed at 20° and 30° buccal tilts was fabricated. Forty impressions were taken from this model, with two groups of full-arch and sectional custom trays (n = 2 × 20), each divided into two subgroups of implant-level and abutment-level techniques (n = 2 × 2 × 10 in four subgroups). Absolute and non-absolute linear and angular impression errors were estimated by comparing the fabricated casts with the model, using a coordinate measuring machine. The effects of sectional/full-arch trays and abutment-level and fixture-level techniques on impression accuracies were analyzed using one- and two-way analyses of variance (ANOVA), Tukey, Mann-Whitney, and one-sample t-tests (α = 0.05, Mann-Whitney's α using the Bonferroni Bonferroni method). No significant differences between the absolute linear errors of the two trays (P = 0.100 [ANOVA]) and the two levels (P = 0.400 [ANOVA]) were observed. The assessment of absolute angular errors showed no significant differences (all P values ≥ 0.4 [ANOVA]). The difference between the linear errors in the full-arch vs. sectional trays was not significant in the fixture-level group (P = 0.290). However, in the abutment-level group, the linear error was significantly greater in the sectional tray compared to full-arch tray (P = 0.013, α = 0.025 [Mann-Whitney]). Using sectional trays might not be advantageous over full-arch trays. Sectional trays are not recommended for taking abutment-level impressions. The abutment

Accuracy of Different Implant Impression Techniques: Evaluation of New Tray Design Concept.

Science.gov (United States)

Liu, David Yu; Cader, Fathima Nashmie; Abduo, Jaafar; Palamara, Joseph

2017-12-29

To evaluate implant impression accuracy with a new tray design concept in comparison to nonsplinted and splinted impression techniques for a 2-implant situation. A reference bar titanium framework was fabricated to fit on 2 parallel implants. The framework was used to generate a resin master model with 2 implants that fit precisely against the framework. Three impression techniques were evaluated: (1) nonsplinted, (2) splinted, and (3) nonsplinted with modified tray impressions. All the trays were fabricated from light-cured acrylic resin material with openings that corresponded to the implant impression copings. Ten impressions were taken for each technique using poly(vinyl siloxane) impression material. The impressions were poured with type IV dental stone to generate the test casts. A rosette strain gauge was bonded to the middle of the framework. As the framework retaining screws were tightened on each test cast, the developed strains were recorded until the completion of the tightening to 35 Ncm. The generated strains of the rosette strain gauge were used to calculate the maximum principal strain. A statistically significant difference was observed among the different impression techniques. The modified tray design impression technique was associated with the least framework strains, which indicates greater accuracy compared with the other techniques. There was no significant difference between the splinted and the nonsplinted impression techniques. The new tray design concept appeared to produce more accurate implant impressions than the other techniques. Despite the statistical difference among the impression techniques, the clinical significance of this difference is yet to be determined. © 2017 by the American College of Prosthodontists.

Idealized flow patterns and transit times in gas/liquid contacting trays with multiple box downcomers

International Nuclear Information System (INIS)

D'Arcy, D.

1977-08-01

Trays with multiple box downcomers are often used in chemical process plants nowadays. In order to make a theoretical assessment of the mass transfer efficiency of such trays, knowledge is needed of the time spent by the liquid at various parts of the tray. An idealized but reasonable flow pattern has been assumed and the local velocities and transit times along ten equally-spaced stream lines have been computed. Numerical and graphical results are presented. (author)

SQUG cable tray and conduit evaluation procedure

International Nuclear Information System (INIS)

Smith, P.D.; Eder, S.J.; Conoscente, J.P.

1990-01-01

Cable tray and conduit systems for electrical cables are a common feature and industrial facilities. They have an excellent performance history in past strong earthquake, even though they are rarely designed for earthquakes. Considerable data have been gathered on their performance in earthquakes and in shake table testing. The data have been used to develop a procedure for the verification of the seismic adequacy of cable tray and conduit systems in operating nuclear plants. The procedure is discussed in this paper. It will result in substantial savings, such as reduced engineering effort, fewer modifications of existing hardware, and simpler documentation, relative to alternate procedures like dynamic analysis of shake table testing. The procedure ensures safety-function in a unique manner since the methodology used to develop it (1) is based on a large body of historical data and (2) uses a relative approach of ensuring that nuclear plant systems will perform at least as well as systems that performed well in past earthquakes. (orig.)

The effect of impression volume and double-arch trays on the registration of maximum intercuspation.

Science.gov (United States)

Hahn, Sara M; Millstein, Philip L; Kinnunen, Taru H; Wright, Robert F

2009-12-01

The type of double-arch trays used may affect occlusion. The purpose of this study was to determine what effect, if any, double-arch tray design and impression material volume had on the registration of maximum intercuspation (MI). Quadrant impressions were made on articulated fracture-resistant dental casts mounted in maximum intercuspation occlusion. Three types of sideless double-arch impression trays were used: First Bite with nylon webbing, Sultan's 3-Way with double crosshatch webbing, and Premium's 3-in-1 Tray with single crosshatch webbing. Vinyl polysiloxane impression material (Aquasil Ultra Rigid Fast Set) was distributed at 2 different volumes (5.4 ml and 8.3 ml), and 60 impressions were made (n=10). A weight of 1.2 kg was placed on the upper arm of an Artex articulator, ensuring complete closure. The impressions were allowed to polymerize for 5 minutes. After polymerization, specimens were placed on a light box, and a camera set at a fixed distance was used to capture the light transmission that was projected through the impression material. The camera transferred the information to an image analysis program (ImageJ). This system allowed the different amounts of light projected through the impression to be translated into a gray scale value (GSV), which was assigned a thickness value, in millimeters, of a specified occlusal contact area. To assess reliability of the experimental design, 10 control impressions were made by directly applying impression material onto the typodont. These were analyzed in the same manner as the impressions made with trays. A 2-way ANOVA comparing volume by tray type was used (alpha=.05). This was followed by a Tukey HSD test. There was no main effect for volume of impression material (P=.71). Tray type was significantly different (Precord making.

Herbal dryer: drying of ginger (zingiber officinale) using tray dryer

Science.gov (United States)

Haryanto, B.; Hasibuan, R.; Alexander; Ashari, M.; Ridha, M.

2018-02-01

Drying is widely used as a method to preserve food because of its convenience and affordability. Drying of ginger using tray dryer were carried out at various drying conditions, such as air-drying flow, air-drying temperature, and sample dimensions, to achieve the highest drying rate. Samples with various dimensions were placed in the tray dryer and dried using various air-drying flow and temperatures. The weights of samples were observed every 3 minutes interval. Drying was stopped after three times of constant weighing. Data of drying was collected to make the drying curves. Drying curves show that the highest drying rate is achieved using highest air flow and temperature.

Challenges to validation of a complex nonsterile medical device tray.

Science.gov (United States)

Prince, Daniel; Mastej, Jozef; Hoverman, Isabel; Chatterjee, Raja; Easton, Diana; Behzad, Daniela

2014-01-01

Validation by steam sterilization of reusable medical devices requires careful attention to many parameters that directly influence whether or not complete sterilization occurs. Complex implant/instrument tray systems have a variety of configurations and components. Geobacillus stearothermophilus biological indicators (BIs) are used in overkill cycles to to simulate worst case conditions and are intended to provide substantial sterilization assurance. Survival of G. stearothermophilus spores was linked to steam access and size of load in the chamber. By a small and reproducible margin, it was determined that placement of the trays in a rigid container into minimally loaded chambers were more difficult to completely sterilize than maximally loaded chambers.

Recolonization of macrofauna in unpolluted sands placed in a polluted yachting harbour: A field approach using experimental trays

Science.gov (United States)

Guerra-García, J. M.; García-Gómez, J. C.

2009-01-01

A field experiment using trays was conducted at Ceuta's yachting harbour, North Africa, to study the effect in recolonization of placing trays with unpolluted defaunate sediments (fine and gross sands with low contents of organic matter) inside an enclosed yachting harbour characterized by high percentages of silt and clay and high concentrations of organic matter. Sediment recolonization in the trays was mainly undertaken by the species living naturally at the yachting harbour, which recolonized both uncontaminated gross and fine sand trays (such as the crustaceans Corophium runcicorne, Corophium sextonae and Nebalia bipes, the mollusc Parvicardium exiguum and the polychaete Pseudomalacoceros tridentata). However, other species like the polychaetes Cirriformia tentaculata and Platynereis dumerilii, although also abundant in the yachting harbour, were unable to colonize the trays through transport of larvae and/or adults in the water column. The recolonization was very quick, and after the first month, the values of abundance, species richness, diversity and evenness were similar in the experimental trays and in the reference area (yachting harbour). Although the multivariate analysis showed that the species composition differed between the trays and the reference area, there were no significant differences in recolonization of gross and fine sands, indicating that other factors different from the granulometry are modulating the recolonization patterns.

Test-based approach to cable tray support system analysis and design: Behavior and test methods

Energy Technology Data Exchange (ETDEWEB)

Reigles, Damon G., E-mail: dreigles@engnovex.com [engNoveX, Inc., 19C Trolley Square, Wilmington, DE 19806 (United States); Brachmann, Ingo; Johnson, William H. [Bechtel Nuclear, Security & Environmental, 12011 Sunset Hills Rd, Suite 110, Reston, VA 20190 (United States); Gürbüz, Orhan [Tobolski Watkins Engineering, Inc., 4125 Sorrento Valley Blvd, Suite B, San Diego, CA 92121 (United States)

2016-06-15

Highlights: • Describes dynamic response behavior of unistrut type cable tray supports. • Summarizes observations from past full-scale shake table test programs. • Outlines testing methodologies necessary to identify key system parameters. - Abstract: Nuclear power plant safety-related cable tray support systems subjected to seismic loadings were originally understood and designed to behave as linear elastic systems. This behavioral paradigm persisted until the early 1980s when, due to evolution of regulatory criteria, some as-installed systems needed to be qualified to higher seismic motions than originally designed for. This requirement prompted a more in-depth consideration of the true seismic response behavior of support systems. Several utilities initiated extensive test programs, which demonstrated that trapeze strut-type cable tray support systems exhibited inelastic and nonlinear response behaviors with plastic hinging at the connections together with high damping due to bouncing of cables in the trays. These observations were used to demonstrate and justify the seismic adequacy of the aforementioned as-installed systems. However, no formalized design methodology or criteria were ever established to facilitate use of these test data for future evaluations. This paper assimilates and reviews the various test data and conclusions for the purpose of developing a design methodology for the seismic qualification of safety-related cable tray support systems.

Apparatus for feeding nuclear fuel pellets to a loading tray

International Nuclear Information System (INIS)

Huggins, T.B.

1979-01-01

Apparatus for feeding nuclear fuel pellets at a uniform predetermined rate between pellet centering and grinding apparatus and a tray for loading pellets into nuclear fuel rod. Pellets discharged from the grinding apparatus are conveyed by a belt to a drive wheel forcing the pellets in engagement with the belt. The pellets under the drive wheel are capable of pushing a line of about 36 pellets onto a pellet dumping mechanism. As the dumping mechanism is actuated to dump the pellets on to a loading tray, the pellets moving toward the mechanism are stopped and the drive wheel is simultaneously lifted off the pellets until the pellet dumping process is completed. (U.K.)

Design, Development and Evaluation of a Pneumatic Seeder for Automatic Planting of Seeds in Cellular Trays

Directory of Open Access Journals (Sweden)

E Movahedi

2014-04-01

Full Text Available For planting fine seeds in cellular trays, an automatic pneumatic seeder was designed, constructed and evaluated. CATIA software was used to design and analysis the system parts of the seeder. Different parts of the seeder, including vibrating seed hopper, vacuum boom, seed picking nozzles, seed tube, pneumatic system and electronic control unit for automation of the seeder, were designed and constructed. The area of nozzle orifice was used to calculate the required pressure of nozzle tip. The seeder was evaluated using two sizes of trays. Experiments were performed with five replications and the error of planting the seeds in the 105 and 390-cellular trays were 1.9 and 0.46 percent, respectively. The time of planting for 105 and 390 cellular trays reduced from 20 min (for manual seeding to 35 s and from 90 min to 160 s, respectively.

Dimensional changes of alginate impression by using perforated and non-perforated ring trays

Directory of Open Access Journals (Sweden)

Sumadhi Sastrodihardjo

2010-03-01

Full Text Available Dimensional changes are a common occurrence in impressions, either during or after impression taking. It produces a difference in the dimensions of the object and the model, which leads to the restoration being ill-fitted. Several causal factors have been proposed such as friction between the impression material and the teeth, the bulk of the impression material, the type of impression materials used, the impression technique, the pouring time and many others. The exact causal factor is still unknown and the dimensional change mechanism is still poorly understood. The objective of this research was to investigate the role of the perforation on the ring trays in producing dimensional changes in the impression by using perforated and non-perforated ring trays. Alginate impressions were made on the frustum of cone metal master die with a 7.08 mm base diameter, 7.03 mm top diameter and 9.23 mm height using perforated and non-perforated ring trays with 9.40 mm in diameter and 14.17 mm in height. The dimensional change was determined by comparing the dimension of the dental stone die and its metal master die. The results showed that the percentage of dimensional changes that occurred by using perforated ring tray were (+ 0.56±0.40 on the top area, (- 3.54±2.92 on base area and (+ 1.54±0.83 in height, respectively. As compared to using non-perforated ring trays, the percentage of dimensional changes that occurred were (- 0.49±0.49 on top area, (- 8.76±3.95 on base area and (+ 1.19±0.71 in height, respectively. There was a significant difference in the direction of the dimensional changes on both the top areas, but not in the base areas and height.

Calculation of electron contamination doses produced using blocking trays for 6 MV X-rays

Energy Technology Data Exchange (ETDEWEB)

Butson, M.J. E-mail: mbutson@guessmail.com; Cheung Tsang; Yu, P.K.N

2002-04-01

Calculation of electron contamination doses whilst using blocking trays in radiotherapy is achieved by comparison of measured absorbed dose within the first few centimeters of a water phantom. Electron contamination of up to 28% of maximum dose is produced at the central axis of the beam whilst using a 6 mm Perspex blocking tray for a 30 cmx30 cm field. The electron contamination is spread over the entire field reducing slightly towards the edge of the beam. Electron contamination from block trays is also present outside the primary collimated X-ray beam with more than 20% of the maximum dose deposited at the surface, 5 cm outside the primary collimated beam at a field size of 40 cmx40 cm. The electron contamination spectrum has been calculated from measured results.

[The geometry of the keel determines the behaviour of the tibial tray against torsional forces in total knee replacement].

Science.gov (United States)

García David, S; Cortijo Martínez, J A; Navarro Bermúdez, I; Maculé, F; Hinarejos, P; Puig-Verdié, L; Monllau, J C; Hernández Hermoso, J A

2014-01-01

The keel design of the tibial tray is essential for the transmission of the majority of the forces to the peripheral bone structures, which have better mechanical proprieties, thus reducing the risk of loosening. The aim of the present study was to compare the behaviour of different tibial tray designs submitted to torsional forces. Four different tibial components were modelled. The 3-D reconstruction was made using the Mimics software. The solid elements were generated by SolidWorks. The finite elements study was done by Unigraphics. A torsional force of 6 Nm. applied to the lateral aspects of each tibial tray was simulated. The GENUTECH® tibial tray, with peripheral trabecular bone support, showed a lower displacement and less transmitted tensions under torsional forces. The results suggest that a tibial tray with more peripheral support behaves mechanically better than the other studied designs. Copyright © 2013 SECOT. Published by Elsevier Espana. All rights reserved.

Evaluation of the bone microstructures after the mandibular reconstruction, using bioresorbable hydroxyapatite/poly-L-lactide mesh tray and the particulate cancellous bone

International Nuclear Information System (INIS)

Takahashi, Hidetoshi; Matsuo, Akira; Chiba, Hiroshige

2010-01-01

The combination of particulate cancellous bone and marrow (PCBM) and a titanium tray is frequently used for mandibular reconstruction. However, there are difficulties in bending the tray and forming a suitable contour. In addition, the metallic ions elute into the living body and the hinders the implant insertion; therefore, a removable operation is required after reconstruction. Hydroxyapatite/poly-L-lactide (HA/PLLA) is a bone-bonding material that has both bio-activity and bio-resorbability. It may overcome the weakness of a titanium tray, but the bone microstructures have not been evaluated after the use of this tray for PCBM reconstruction. We created defects on the mandible of a beagle and reconstructed it by filling it with a mixture of PCBM and PRP using the HA/PLLA tray. We examined the bone-formation mechanism using a confocal laser microscope and bone microstructural analysis using microCT. As a result, compared to the titanium tray, the bone-formation is delayed during the first 3 to 6 months with an HA/PLLA tray. However, a formation of new bone with equal quality is observed after 12 months. According to the bone microstructural measurement, both of them had higher bone volume fraction than the native bone but other parameters were the same. From the above, the quantity of the new bone in the HA/PLLA tray is the same as the bone in the titanium tray, and has equal bone microstructures with the surrounding native bone. (author)

Treatability test of a stacked-tray air stripper for VOC in water

Energy Technology Data Exchange (ETDEWEB)

Pico, T., LLNL

1998-04-01

A common strategy for hydraulic containment and mass removal at VOC contaminated sites is `pump and treat (P&T)`. In P&T operations, contaminated ground water is pumped from wells, treated above ground, and discharged. Many P&T remediation systems at VOC sites rely on air stripping technology because VOCs are easily transferred to the vapor phase. In stacked-tray air strippers, contaminated water is aerated while it flows down through a series of trays. System operations at LLNL are strictly regulated by the California and federal Environmental Protection Agencies (Cal/EPA and EPA), the Bay Area Air Quality Management District (BAAQMD), the California Regional Water Quality Control Board (RWQCB) and the Department of Toxic Substances Control (DTSC). These agencies set discharge limits, require performance monitoring, and assess penalties for non-compliance. National laboratories are also subject to scrutiny by the public and other government agencies. This extensive oversight makes it necessary to accurately predict field treatment performance at new extraction locations to ensure compliance with all requirements prior to facility activation. This paper presents treatability test results for a stacked- tray air stripper conducted at LLNL and compares them to the vendor`s modeling software results.

Journal of EEA, Vol. 30, 2013 SIEVE TRAY EFFICIENCY USING ...

African Journals Online (AJOL)

dell

Journal of EEA, Vol. 30, 2013. SIEVE TRAY EFFICIENCY USING CFD MODELING AND SIMULATION ... ABSTRACT. In this work, computational fluid dynamics (CFD) .... per unit volume, MG is the molecular weight of the gas/vapor, kL and kG ...

SWAP-Assembler 2: Optimization of De Novo Genome Assembler at Large Scale

Energy Technology Data Exchange (ETDEWEB)

Meng, Jintao; Seo, Sangmin; Balaji, Pavan; Wei, Yanjie; Wang, Bingqiang; Feng, Shengzhong

2016-08-16

In this paper, we analyze and optimize the most time-consuming steps of the SWAP-Assembler, a parallel genome assembler, so that it can scale to a large number of cores for huge genomes with the size of sequencing data ranging from terabyes to petabytes. According to the performance analysis results, the most time-consuming steps are input parallelization, k-mer graph construction, and graph simplification (edge merging). For the input parallelization, the input data is divided into virtual fragments with nearly equal size, and the start position and end position of each fragment are automatically separated at the beginning of the reads. In k-mer graph construction, in order to improve the communication efficiency, the message size is kept constant between any two processes by proportionally increasing the number of nucleotides to the number of processes in the input parallelization step for each round. The memory usage is also decreased because only a small part of the input data is processed in each round. With graph simplification, the communication protocol reduces the number of communication loops from four to two loops and decreases the idle communication time. The optimized assembler is denoted as SWAP-Assembler 2 (SWAP2). In our experiments using a 1000 Genomes project dataset of 4 terabytes (the largest dataset ever used for assembling) on the supercomputer Mira, the results show that SWAP2 scales to 131,072 cores with an efficiency of 40%. We also compared our work with both the HipMER assembler and the SWAP-Assembler. On the Yanhuang dataset of 300 gigabytes, SWAP2 shows a 3X speedup and 4X better scalability compared with the HipMer assembler and is 45 times faster than the SWAP-Assembler. The SWAP2 software is available at https://sourceforge.net/projects/swapassembler.

Bactericidal paper trays doped with silver nanoparticles for egg ...

Indian Academy of Sciences (India)

the AgNPs-deposited paper egg trays improved the shelf-life of the eggs by more than 14 days ... In this work, we developed a new method to prepare anti- ... on an electronic balance (Sartorius). ..... significant changes with respect to physical quality param- ... Due to possible human health effects from silver exposure,.

Fabrication of customized sectional impression trays in management of patients with limited mouth opening: a simple and unique approach.

Science.gov (United States)

Krishna Ch, Vamsi; Mahendranadh Reddy, K; Gupta, Nidhi; Mahadev Shastry, Y; Chandra Sekhar, N; Aditya, Venkat; Reddy, G V K Mohan

2013-01-01

Impression making is not only important but is also the most significant step in the fabrication of any fixed or removable prosthesis. Proper impression making may be hindered by certain pathologic conditions. Reduced mouth opening is one of the common mechanical obstructions for proper orientation of the impression tray in the patient's mouth. In patients with trismus induced by submucous fibrosis, the procedure may be even more difficult to carry out because of reduced tissue resiliency and obliteration of vestibular spaces. Use of sectional trays offers one of the alternatives to overcome the problem of restricted mouth opening. Fabrication of customized impression trays according to the patient dentition improves the accuracy of impression making. The present case reports describe the fabrication of sectional custom trays designed for dentulous patients with chronic tobacco-induced submucous fibrosis.

Simulators of tray distillation columns as tools for interpreting ...

African Journals Online (AJOL)

... at 0.05 m intervals were determined from top to the bottom of simulators of tray distillation columns exposed to 20 mCi of 137 Cs. Signals generated from the simulators were identical with the experimental signals obtained from the Stabilizer Column of the crude oil distillation unit at the Tema Oil Refinery Ghana Limited.

Production of diosgenin from Dioscorea zingiberensis with mixed culture in a new tray bioreactor

Directory of Open Access Journals (Sweden)

Yutong Cheng

2016-01-01

Full Text Available A new tray bioreactor was developed for the production of diosgenin from Dioscorea zingiberensis with Trichoderma reesei and Aspergillus fumigatus. The influence of initial moisture content, temperature, tray bed depth and mixing times was investigated. The best fermentation condition is initial moisture content of 75%, bioreactor temperature of 35°C, solid bed depth of 1.5 cm and three mixings carrying out on the first, third and fifth day. Under the optimized fermentation conditions, after 144 h incubation, maximum diogenin concentration of 68.2 μmol/g was detected.

Reduction of seismic loads in cable tray hangers

International Nuclear Information System (INIS)

Pearce, B.K.; Jackson, J.E.; Dixon, M.W.; Bourne, F.R.

1984-01-01

A study has been conducted to partially assess the feasibility of using flexible rather than rigid support systems for carrying electrical and control cables in nuclear power plants. Using analytical and experimental studies, it was found that a flexible hanger design with appropriate stiffness and damping characteristics could be used to isolate trays from hanger vibration and significantly reduce hanger loads during seismic events if the connectors could be adequately tuned to account for system variables. Finite element techniques were used to select a flexible connector for a specified base hanger system. Tests were conducted on one-third-scale models to establish values for some of the parameters and to partially verify the analytical methods. For the hanger systems considered, introduction of the flexible connector allowed support-hanger loads and hanger displacements to be reduced greatly while satisfying tray displacement constraints. It appears that a flexible-connector system can provide better dynamic response than the conventional type system using rigid connectors. This conclusion is valid for all variations in system parameters studied. Although the flexible-connector concept looks very promising based on this study, substantial work, including full-scale testing, must be completed before this concept can be validated for actual plant designs. (orig.)

Numerical prediction of fire extinguishment characteristics of sodium leak collection tray in a fast breeder reactor

International Nuclear Information System (INIS)

Diwakar, S.V.; Mangarjuna Rao, P.; Kasinathan, N.; Das, Sarit K.; Sundararajan, T.

2011-01-01

Highlights: ► Sodium fire extinguishment in a leak collection tray is modeled by lumped approach. ► Hydrodynamics of liquid sodium on tray is emulated through a draining/sloshing model. ► Pool burning rates in the tray and holdup vessel are numerically estimated. ► The model directly yields the mass of sodium recovered after extinction of fire. ► Model predictions are in reasonable agreement with the available experimental data. - Abstract: Sodium leak collection tray (LCT) is an efficient passive device used for the extinguishment of liquid sodium fire in case of an accidental leakage from the secondary circuit of a fast breeder reactor. The LCT essentially isolates the leaking sodium into closed containers where the resulting fire is extinguished due to limited availability of oxygen. The current work aims to highlight the combustion extinguishment characteristics of LCT through a lumped formulation by conserving the mass and energy of liquid sodium and constituent gases in various parts of the LCT. Here, the complex hydrodynamics of liquid sodium is emulated through a semi-analytical draining/sloshing model and its burning rates are predicted through a three-dimensional open pool combustion model for the tray region and a closed pool combustion model for the holdup vessel. These simulations evaluate the burning rates at discrete levels of liquid sodium which are subsequently interpolated to establish correlations involving instantaneous liquid levels and oxygen concentration. Using the correlations obtained from the draining and combustion models, the overall lumped formulation directly predicts the un-burnt sodium recoverable after the extinguishment of fire in the LCT. The predicted results of this model compare well with the available experimental data.

A comparative evaluation of genome assembly reconciliation tools.

Science.gov (United States)

Alhakami, Hind; Mirebrahim, Hamid; Lonardi, Stefano

2017-05-18

The majority of eukaryotic genomes are unfinished due to the algorithmic challenges of assembling them. A variety of assembly and scaffolding tools are available, but it is not always obvious which tool or parameters to use for a specific genome size and complexity. It is, therefore, common practice to produce multiple assemblies using different assemblers and parameters, then select the best one for public release. A more compelling approach would allow one to merge multiple assemblies with the intent of producing a higher quality consensus assembly, which is the objective of assembly reconciliation. Several assembly reconciliation tools have been proposed in the literature, but their strengths and weaknesses have never been compared on a common dataset. We fill this need with this work, in which we report on an extensive comparative evaluation of several tools. Specifically, we evaluate contiguity, correctness, coverage, and the duplication ratio of the merged assembly compared to the individual assemblies provided as input. None of the tools we tested consistently improved the quality of the input GAGE and synthetic assemblies. Our experiments show an increase in contiguity in the consensus assembly when the original assemblies already have high quality. In terms of correctness, the quality of the results depends on the specific tool, as well as on the quality and the ranking of the input assemblies. In general, the number of misassemblies ranges from being comparable to the best of the input assembly to being comparable to the worst of the input assembly.

Optimal space utilization of a greenhouse using multi-rack tray system: Thermal modeling and experimental validation

International Nuclear Information System (INIS)

Sethi, V.P.; Dubey, R.K.

2008-01-01

In this study, upper space inside an east-west oriented greenhouse (where the micro-climate is also under control) is optimised for producing maximum number of nursery plants by developing a multi-rack tray system (MRTS). The MRTS is designed in such a way that the vertical distance between the two consecutive trays (H) and width of the tray (W) is optimised for different months of the year at different latitudes so that the shadow of the upper tray does not fall on the lower one. The number of stacks in a greenhouse of fixed height (say 4 m) is a direct function of the maximum altitude angle of the sun at noon (α s ) at particular latitude. It is observed that at 10 deg. N and 20 deg. N latitudes α s remains greater than 45 deg. (H/W > 1) even during the winter months. It means not more than two stacks are possible inside a 4 m high greenhouse during December and January. The computations show that at 30 deg. N, 40 deg. N and 50 deg. N latitude, the number of stacks inside a greenhouse can be five, seven and twelve, respectively during the winter months of December and January. A transient thermal model coupled with MRTS is also developed to predict the soil, plant and air temperature inside the greenhouse. It is observed that the predicted and measured values are in close agreement. It is also observed that due to the increased mass of soil (in the trays) inside the greenhouse and due to reduced conduction losses to the ground beneath, MRTS also acted as a soil heat storage system before germination of the plants which stored heat during the sun-shine hours and released the same during the off-shine hours and resulted in 5-2deg. C higher inside air temperature till the early night hours as compared to ambient air temperature. Nursery of marigold (ornamental plant) is successfully raised using the MRTS inside a 3 m high greenhouse having three stacks at 30 deg. N latitude. Experiments showed that there was almost uniform growth of plants in all the three trays

Training to Increase Safe Tray Carrying Among Cocktail Servers

OpenAIRE

Scherrer, Megan D; Wilder, David A

2008-01-01

We evaluated the effects of training on proper carrying techniques among 3 cocktail servers to increase safe tray carrying on the job and reduce participants' risk of developing musculoskeletal disorders. As participants delivered drinks to their tables, their finger, arm, and neck positions were observed and recorded. Each participant received individual safety training that focused on proper carrying positions and techniques after baseline data were collected. A multiple baseline design acr...

Dimensional changes in plaster cast models due to the position of the impression tray during setting

Directory of Open Access Journals (Sweden)

Betina Grehs Porto

2014-01-01

Full Text Available Introduction: The objective of this study was to assess whether the positioning of the impression tray could cause distortion to plaster casts during gypsum setting time.Materials and Methods: Fifteen pairs of master models were cast with alginate impression material and immediately filled with gypsum. Impressions were allowed to set with the tray in the noninverted position (Group A or in the inverted position (Group B. The plaster models were digitized using a laser scanner (3Shape R-700, 3Shape A/S, Copenhagen, Denmark. Measurements of tooth size and distance were obtained using O3d software (Widialabs, Brazil measurement tools. Data were analyzed by paired t-test and linear regression with 5% significance.Results and Conclusion: Most of the measurements from both groups were similar, except forthe lower intermolar distance. It was not possible to corroborate the presence of distortions due to the position of the impression tray during gypsum setting time.

Hydromechanical transmission with three simple planetary assemblies, one sun gear being mounted on the output shaft and the other two on a common shaft connected to an input-driven hydraulic module

Science.gov (United States)

Orshansky, Jr., deceased, Elias; Weseloh, William E.

1978-01-01

A power transmission having three simple planetary assemblies, each having its own carrier and its own planet, sun, and ring gears. A speed-varying module is connected in driving relation to the input shaft and in driving relationship to the sun gears of the first two planetary assemblies, these two sun gears being connected together on a common shaft. The speed-varying means may comprise a pair of hydraulic units hydraulically interconnected so that one serves as a pump while the other serves as a motor and vice versa, one of the units having a variable stroke and being connected in driving relation to the input shaft, the other unit, which may have a fixed stroke, being connected in driving relation to the sun gears. The input shaft is also connected to drive the second ring gear and, furthermore is clutchable to the carrier of the third planetary assembly. A brake grounds the first carrier in the first range and in reverse and causes drive to be delivered to the output through the first ring gear in a hydrostatic mode. The carrier of the second planetary assembly drives the ring gear of the third planetary assembly, which is clutchable to the output shaft, and the sun gear of the third planetary assembly is mounted rigidly to the output shaft.

The Economics of Applying Suppressive Shielding to the M483A1 Improved Conventional Munition Loading, Assembling, and Packing Facility

Science.gov (United States)

1977-01-01

trays are placed on a cart (206-pound net explosive). These carts are moved by driverless tractor to an 8-hour hold in a nearby building while quality...by driverless tractor to a 40-hour hold for quality assurance inspection. After inspection, the grenades are returned to the loading, assembling, and

Custom sectional impression trays with interlocking type handle for microstomia patients

Directory of Open Access Journals (Sweden)

Fernandes Aquaviva

2009-01-01

Full Text Available Making impressions in microstomia patients is often cumbersome. A modification of standard impression procedure is often necessary while treating such patients. This article describes the fabrication of a custom sectional impression tray with interlocking type of a handle for definitive impression procedures in a microstomia patient.

Study on The Effectiveness of Egg Tray and Coir Fibre as A Sound Absorber

Science.gov (United States)

Kaamin, Masiri; Farah Atiqah Ahmad, Nor; Ngadiman, Norhayati; Kadir, Aslila Abdul; Razali, Siti Nooraiin Mohd; Mokhtar, Mardiha; Sahat, Suhaila

2018-03-01

Sound or noise pollution has become one major issues to the community especially those who lived in the urban areas. It does affect the activity of human life. This excessive noise is mainly caused by machines, traffic, motor vehicles and also any unwanted sounds that coming from outside and even from the inside of the building. Such as a loud music. Therefore, the installation of sound absorption panel is one way to reduce the noise pollution inside a building. The selected material must be a porous and hollow in order to absorb high frequency sound. This study was conducted to evaluate the potential of egg tray and coir fibre as a sound absorption panel. The coir fibre has a good coefficient value which make it suitable as a sound absorption material and can replace the traditional material; syntactic and wooden material. The combination of pyramid shape of egg tray can provide a large surface for uniform sound reflection. This study was conducted by using a panel with size 1 m x 1 m with a thickness of 6 mm. This panel consist of egg tray layer, coir fibre layer and a fabric as a wrapping for the aesthetic value. Room reverberation test has been carried to find the loss of reverberation time (RT). Result shows that, a reverberation time reading is on low frequency, which is 125 Hz to 1600 Hz. Within these frequencies, this panel can shorten the reverberation time of 5.63s to 3.60s. Hence, from this study, it can be concluded that the selected materials have the potential as a good sound absorption panel. The comparison is made with the previous research that used egg tray and kapok as a sound absorption panel.

Study on The Effectiveness of Egg Tray and Coir Fibre as A Sound Absorber

Directory of Open Access Journals (Sweden)

Kaamin Masiri

2018-01-01

Full Text Available Sound or noise pollution has become one major issues to the community especially those who lived in the urban areas. It does affect the activity of human life. This excessive noise is mainly caused by machines, traffic, motor vehicles and also any unwanted sounds that coming from outside and even from the inside of the building. Such as a loud music. Therefore, the installation of sound absorption panel is one way to reduce the noise pollution inside a building. The selected material must be a porous and hollow in order to absorb high frequency sound. This study was conducted to evaluate the potential of egg tray and coir fibre as a sound absorption panel. The coir fibre has a good coefficient value which make it suitable as a sound absorption material and can replace the traditional material; syntactic and wooden material. The combination of pyramid shape of egg tray can provide a large surface for uniform sound reflection. This study was conducted by using a panel with size 1 m x 1 m with a thickness of 6 mm. This panel consist of egg tray layer, coir fibre layer and a fabric as a wrapping for the aesthetic value. Room reverberation test has been carried to find the loss of reverberation time (RT. Result shows that, a reverberation time reading is on low frequency, which is 125 Hz to 1600 Hz. Within these frequencies, this panel can shorten the reverberation time of 5.63s to 3.60s. Hence, from this study, it can be concluded that the selected materials have the potential as a good sound absorption panel. The comparison is made with the previous research that used egg tray and kapok as a sound absorption panel.

Simulators of tray distillation columns as tools for interpreting gamma-ray scan profile signal

International Nuclear Information System (INIS)

Offei-Mensah, P.S.; Gbadago, J.K.; Dagadu, C.P.K.; Danso, K.A.

2008-01-01

Simulators of tray distillation columns were used to provide technical guidelines for interpreting signals from gamma ray scans used for analysing malfunctions in distillation columns. The transmitted radiation intensities at 0.05 m intervals were determined from top to bottom of simulators of tray distillation columns exposed to 20 mCi of '1'3'7 Cs. Signals generated from the simulators were identical with the experimental signals obtained from the stabilizer column of the crude oil distillation unit at the Tema Oil Refinery Ghana Limited. Changes in the signal level were observed with changes in diameter, type of material (gasoline, air, debris, steel) and orientation of scan line. The analysis provided accurate interpretation of gamma scan profiles. (au)

Normative data for distal line bisection and baking tray task.

Science.gov (United States)

Facchin, Alessio; Beschin, Nicoletta; Pisano, Alessia; Reverberi, Cristina

2016-09-01

Line bisection is one of the tests used to diagnose unilateral spatial neglect (USN). Despite its wide application, no procedure or norms were available for the distal variant when the task was performed at distance with a laser pointer. Furthermore, the baking tray task was an ecological test aimed at diagnosing USN in a more natural context. The aim of this study was to collect normative values for these two tests in an Italian population. We recruited a sample of 191 healthy subjects with ages ranging from 20 to 89 years. They performed line bisection with a laser pointer on three different line lengths (1, 1.5, and 2 m) at a distance of 3 m. After this task, the subjects performed the baking tray task and a second repetition of line bisection to test the reliability of measurement. Multiple regression analysis revealed no significant effects of demographic variables on the performance of both tests. Normative cut-off values for the two tests were developed using non-parametric tolerance intervals. The results formed the basis for clinical use of these two tools for assessing lateralized performance of patients with brain injury and for diagnosing USN.

Pilot Overmyer looks over food selections and experiments with beverage

Science.gov (United States)

1982-01-01

Pilot Overmyer, using beverage container and drinking straw secured in meal tray assembly (ASSY), experiments with microgravity chararcteristics of liquid on middeck in front of forward lockers. Overmyer also looks over packages of food attached to middeck lockers in meal tray assemblies. Carry-on food warmer appears overhead and other meal tray assemblies, personal hygiene mirror assy, personal hygiene kit, and portrait of G.W.S. Abbey, JSC's Director of Flight Operations, appear on lockers.

Towards functional 3D T-ray imaging

International Nuclear Information System (INIS)

Ferguson, Bradley; Wang, Shaohong; Gray, Doug; Abbott, Derek; Zhang, X-C

2002-01-01

We review the recent development of T-ray computed tomography, a terahertz imaging technique that allows the reconstruction of the three-dimensional refractive index profile of weakly scattering objects. Terahertz pulse imaging is used to obtain images of the target at multiple projection angles and the filtered backprojection algorithm enables the reconstruction of the object's frequency-dependent refractive index. The application of this technique to a biological bone sample and a plastic test structure is demonstrated. The structure of each target is accurately resolved and the frequency-dependent refractive index is determined. The frequency-dependent information may potentially be used to extract functional information from the target, to uniquely identify different materials or to diagnose medical conditions

ANALISIS KELAYAKAN TEKNIS DAN FINANSIAL DARI INVESTASI PENGADAAN TRAY DRYER BERBAHAN BAKAR BIOMASSA PADA USAHA ARANG TEMPURUNG KELAPA BERBASIS EKSPOR (Studi Kasus di Tropica Nucifera Industry – Yogyakarta

Directory of Open Access Journals (Sweden)

Fanny Widadie

2013-11-01

Full Text Available The purpose of the study is to assess the technical and financial feasibility of procurement investment Tray Dryer fueled biomass to operations of coconut shell charcoal briquette in PT. Tropica Nucifera Industry. The result showed that investment-Tray Dryer on cocnut shell charcoal briquette bussiness was highly feasibile both the technical and financial aspects. The technical aspect was seen that the quantity-production capabilities of coconut shell charcoal briquettes using a dryer-Tray Dryer could be increased 15 percent compared the previous consdition-used of solar energy. While the quality of the charcoal briquettes produced from Tray Dryer was a much butter quality, moisture content (6.39%; ash (2.65%; carbon-bound (85.83%, compared to using sunlight, water content (15.89; ash (2.57% and carbon-bound (77.32%.The financial aspects of procurement Tray Dryer investment that its value was more feasible than previous, nothing Tray Dryer. Coconut shell charcoal briquet enterprises without using Tray Dryer was feasible to be done with NPV 1,058,928.12, IRR 63%, Payback Period 1 year and 9 moths, Net B/C 2.25 and analysis of swicthcing value reached 20 percent. And after the business using Tray Drayer, the financial analysis was much more feasible with NPV 2,285,500,498.12, IRR 113%, Payback Period 11 months, Net B/C 3.5 and analysis of switching value reached 50 percent.

Development of an integrated, unattended assay system for LWR-MOX fuel pellet trays

International Nuclear Information System (INIS)

Stewart, J.E.; Hatcher, C.R.; Pollat, L.L.

1994-01-01

Four identical unattended plutonium assay systems have been developed for use at the new light-water-reactor mixed oxide (LWR-MOX) fuel fabrication facility at Hanau, Germany. The systems provide quantitative plutonium verification for all MOX pellet trays entering or leaving a large, intermediate store. Pellet-tray transport and storage systems are highly automated. Data from the ''I-Point'' (information point) assay systems will be shared by the Euratom and International Atomic Energy Agency (IAEA) Inspectorates. The I-Point system integrates, for the first time, passive neutron coincidence counting (NCC) with electro-mechanical sensing (EMS) in unattended mode. Also, provisions have been made for adding high-resolution gamma spectroscopy. The system accumulates data for every tray entering or leaving the store between inspector visits. During an inspection, data are analyzed and compared with operator declarations for the previous inspection period, nominally one month. Specification of the I-point system resulted from a collaboration between the IAEA, Euratom, Siemens, and Los Alamos. Hardware was developed by Siemens and Los Alamos through a bilateral agreement between the German Federal Ministry of Research and Technology (BMFT) and the US DOE. Siemens also provided the EMS subsystem, including software. Through the USSupport Program to the IAEA, Los Alamos developed the NCC software (NCC COLLECT) and also the software for merging and reviewing the EMS and NCC data (MERGE/REVIEW). This paper describes the overall I-Point system, but emphasizes the NCC subsystem, along with the NCC COLLECT and MERGE/REVIEW codes. We also summarize comprehensive testing results that define the quality of assay performance

Preliminary design, construction and evaluation of robot of tomato seed planting for the trays of greenhouse

Directory of Open Access Journals (Sweden)

J Ghezavati

2015-09-01

Full Text Available Introduction: From an economic viewpoint, tomato is considered as the second most valuable crop after potato. It is also preceded by the potato in terms of per capita consumption in the world. In 2008, the cultivation area used for the tomato as equal to 163,539 hectares in Iran and the production of it was equal to 5,887,715 tons with an average production of 117,887 tons in 4352 hectares in the provinces, respectively. Having high production volume and quality, costly hybrid seeds are currently used for the major planting areas of vegetable in Iran. Most of the used transplanted seedlings are 83%. Since the seeds are expensive, the percentage of seedlings and healthy and disease-free seeds should be used for maximized germination and be transferred to the fields of open space. Preparing seedlings in transplanting trays is a technology to respond to this need. Trays are covered with a layer of Peat and Miculite fertilizers. Then, one seed is manually placed in each cell after gauging and preparing a suitable field. However, manually placing seeds is time-consuming and requires hard labor. Sixteen working labors per hour are required for 15 × 7 cell in order to have 10200 seedlings grown in 100 trays. Due to lack of adequate labor, production capacity of greenhouses is reduced, especially in the farming season when finding labor for planting vegetable sprouts is laborious. Therefore, mechanizing tray seeding operations is essential to increase the capacity of the growing industry of greenhouses in Iran. Materials and Methods: Initially, the tomato seeds were examined in the laboratory. The most important parameters of the study included size, shape, weight, the speed of getting out of the tank and the minimum carrying speed. Then, a vacuum-based single seed picking unit was prepared to investigate the factors influencing the design, so that a single tomato seed can be harvested from the masses. The most important factors considered in the

Implementing Adlerian Sand Tray Therapy with Adult Male Substance Abuse Offenders: A Phenomenological Inquiry

Science.gov (United States)

Monakes, Sarah; Garza, Yvonne; Wiesner, Van, III; Watts, Richard E.

2011-01-01

The purpose of this phenomenological study was to understand the perceptions of adult male substance offenders who experienced sand tray therapy as an adjunct to their cognitive behavioral rehabilitative treatment. Results indicate a positive experience for participants. Implications for counselors are discussed. (Contains 1 table.)

Integrated magnetic transformer assembly

DEFF Research Database (Denmark)

2014-01-01

The present invention relates to an integrated magnetics transformer assembly comprising a first magnetically permeable core forming a first substantially closed magnetic flux path and a second magnetically permeable core forming a second substantially closed magnetic flux path. A first input...... inductor winding is wound around a first predetermined segment of the first magnetically permeable core and a second input inductor winding is wound around a first predetermined segment of the second magnetically permeable core. The integrated magnetics transformer assembly further comprises a first output......-winding of the first output inductor winding and the first half-winding of the second output inductor winding are configured to produce aligned, i.e. in the same direction, magnetic fluxes through the first substantially closed magnetic flux path. The integrated magnetics transformer assembly is well- suited for use...

Implementation of a robotic flexible assembly system

Science.gov (United States)

Benton, Ronald C.

1987-01-01

As part of the Intelligent Task Automation program, a team developed enabling technologies for programmable, sensory controlled manipulation in unstructured environments. These technologies include 2-D/3-D vision sensing and understanding, force sensing and high speed force control, 2.5-D vision alignment and control, and multiple processor architectures. The subsequent design of a flexible, programmable, sensor controlled robotic assembly system for small electromechanical devices is described using these technologies and ongoing implementation and integration efforts. Using vision, the system picks parts dumped randomly in a tray. Using vision and force control, it performs high speed part mating, in-process monitoring/verification of expected results and autonomous recovery from some errors. It is programmed off line with semiautomatic action planning.

Development of mechanical methods for cell-tray propagation and field transplanting of dwarf napiergrass (Pennisetum purpureum Schumach.

Directory of Open Access Journals (Sweden)

Renny Fatmyah Utamy

2016-01-01

Full Text Available Since dwarf napiergrass (Pennisetum purpureum Schumach. must be propagated vegetatively due to lack of viable seeds, root splitting and stem cuttings are generally used to obtain true-to-type plant populations. These ordinary methods are laborious and costly, and are the greatest barriers for expanding the cultivation area of this crop. The objectives of this research were to develop nursery production of dwarf napiergrass in cell trays and to compare the efficiency of mechanical versus manual methods for cell-tray propagation and field transplanting. After defoliation of herbage either by a sickle (manually or hand-mowing machine, every potential aerial tiller bud was cut to a single one for transplanting into cell trays as stem cuttings and placed in a glasshouse over winter. The following June, nursery plants were trimmed to a 25–cm length and transplanted in an experimental field (sandy soil with 20,000 plants ha^(−1 either by shovel (manually or Welsh onion planter. Labour time was recorded for each process. The manual defoliation of plants required 44% more labour time for preparing the stem cuttings (0.73 person-min. stemcutting^(−1 compared to using hand-mowing machinery (0.51 person-min. stem-cutting^(−1. In contrast, labour time for transplanting required an extra 0.30 person-min. m^(−2 (14% using the machinery compared to manual transplanting, possibly due to the limited plot size for machinery operation. The transplanting method had no significant effect on plant establishment or plant growth, except for herbage yield 110 days after planting. Defoliation of herbage by machinery, production using a cell-tray nursery and mechanical transplanting reduced the labour intensity of dwarf napiergrass propagation.

Computational study of the heat transfer of an avian egg in a tray.

Science.gov (United States)

Eren Ozcan, S; Andriessens, S; Berckmans, D

2010-04-01

The development of an embryo in an avian egg depends largely on its temperature. The embryo temperature is affected by its environment and the heat produced by the egg. In this paper, eggshell temperature and the heat transfer characteristics from one egg in a tray toward its environment are studied by means of computational fluid dynamics (CFD). Computational fluid dynamics simulations have the advantage of providing extensive 3-dimensional information on velocity and eggshell temperature distribution around an egg that otherwise is not possible to obtain by experiments. However, CFD results need to be validated against experimental data. The objectives were (1) to find out whether CFD can successfully simulate eggshell temperature from one egg in a tray by comparing to previously conducted experiments, (2) to visualize air flow and air temperature distribution around the egg in a detailed way, and (3) to perform sensitivity analysis on several variables affecting heat transfer. To this end, a CFD model was validated using 2 sets of temperature measurements yielding an effective model. From these simulations, it can be concluded that CFD can effectively be used to analyze heat transfer characteristics and eggshell temperature distribution around an egg. In addition, air flow and temperature distribution around the egg are visualized. It has been observed that temperature differences up to 2.6 degrees C are possible at high heat production (285 mW) and horizontal low flow rates (0.5 m/s). Sensitivity analysis indicates that average eggshell temperature is mainly affected by the inlet air velocity and temperature, flow direction, and the metabolic heat of the embryo and less by the thermal conductivity and emissivity of the egg and thermal emissivity of the tray.

Use of slow-release fertilizer on the production of sweet potatoes plantlets in tray

Directory of Open Access Journals (Sweden)

Amarílis Beraldo Rós

2013-12-01

Full Text Available The production of plantlets in containers generally requires the use of fertilizers. The aim of this study was to evaluate the production of sweet potato in styrofoam trays using slow-release fertilizer. The experiment was carried out, under a screen-protected nursery, in a factorial scheme 5x5, with five doses of slow-release fertilizer NPK 19-06-10 (0, 50, 100, 150 e 200 g per 25 kg de substrate and five times of plantlets permanence in tray (14, 28, 42, 56 and 70 days after planting the cuttings. The number and dry matter of roots and leaves were evaluated. The number of roots was not influenced by fertilizer addition. In general, there is not damage to plantlets growth until the highest dose used. Therefore, the fertilizer addition increases the sweet potato plants growth and the dose of 200 g per 25 kg of substrate is responsible for the best results.

File list: InP.Adp.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Adp.10.Input_control.AllCell hg19 Input control Input control Adipocyte SRX0194...p://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Adp.10.Input_control.AllCell.bed ...

File list: InP.Unc.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.20.Input_control.AllCell sacCer3 Input control Input control Unclassified E.../dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.Unc.20.Input_control.AllCell.bed ...

File list: InP.Epd.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Epd.50.Input_control.AllCell mm9 Input control Input control Epidermis SRX14260...tp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Epd.50.Input_control.AllCell.bed ...

File list: InP.PSC.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.PSC.05.Input_control.AllCell mm9 Input control Input control Pluripotent stem c... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.PSC.05.Input_control.AllCell.bed ...

File list: InP.Epd.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Epd.20.Input_control.AllCell mm9 Input control Input control Epidermis SRX70095...tp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Epd.20.Input_control.AllCell.bed ...

File list: InP.ALL.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.05.Input_control.AllCell dm3 Input control Input control All cell types SRX...ttp://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.ALL.05.Input_control.AllCell.bed ...

File list: InP.Emb.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Emb.50.Input_control.AllCell dm3 Input control Input control Embryo SRX681824,S...http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Emb.50.Input_control.AllCell.bed ...

File list: InP.ALL.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.50.Input_control.AllCell sacCer3 Input control Input control All cell types.../dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.ALL.50.Input_control.AllCell.bed ...

File list: InP.Adp.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Adp.05.Input_control.AllCell mm9 Input control Input control Adipocyte SRX99775...27370 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Adp.05.Input_control.AllCell.bed ...

File list: InP.Neu.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Neu.20.Input_control.AllCell hg19 Input control Input control Neural SRX643470,...SRX026881 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Neu.20.Input_control.AllCell.bed ...

File list: InP.PSC.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.PSC.05.Input_control.AllCell hg19 Input control Input control Pluripotent stem ...RX342849,ERX342851 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.PSC.05.Input_control.AllCell.bed ...

File list: InP.Plc.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Plc.50.Input_control.AllCell hg19 Input control Input control Placenta SRX19004...9,SRX080366 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Plc.50.Input_control.AllCell.bed ...

File list: InP.Neu.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Neu.10.Input_control.AllCell hg19 Input control Input control Neural SRX643470,...RX1035591 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Neu.10.Input_control.AllCell.bed ...

File list: InP.PSC.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.PSC.20.Input_control.AllCell hg19 Input control Input control Pluripotent stem ...RX342850,ERX342851 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.PSC.20.Input_control.AllCell.bed ...

File list: InP.Bon.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bon.05.Input_control.AllCell hg19 Input control Input control Bone SRX188789,SR...08 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Bon.05.Input_control.AllCell.bed ...

File list: InP.Lar.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lar.05.Input_control.AllCell ce10 Input control Input control Larvae SRX331089,...,SRX015099 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/InP.Lar.05.Input_control.AllCell.bed ...

File list: InP.YSt.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.YSt.50.Input_control.AllCell sacCer3 Input control Input control Yeast strain S... http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.YSt.50.Input_control.AllCell.bed ...

File list: InP.Myo.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Myo.05.Input_control.AllCell hg19 Input control Input control Muscle SRX018653,...656,SRX038601 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Myo.05.Input_control.AllCell.bed ...

File list: InP.Plc.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Plc.05.Input_control.AllCell hg19 Input control Input control Placenta SRX19004...9,SRX080366 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Plc.05.Input_control.AllCell.bed ...

File list: InP.Bon.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bon.10.Input_control.AllCell hg19 Input control Input control Bone SRX188789,SR...64 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Bon.10.Input_control.AllCell.bed ...

File list: InP.PSC.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.PSC.10.Input_control.AllCell hg19 Input control Input control Pluripotent stem ...RX342849,ERX342851 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.PSC.10.Input_control.AllCell.bed ...

File list: InP.Myo.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Myo.05.Input_control.AllCell mm9 Input control Input control Muscle SRX1482291,...62124,SRX022849 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Myo.05.Input_control.AllCell.bed ...

File list: InP.Myo.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Myo.10.Input_control.AllCell hg19 Input control Input control Muscle SRX018653,...652,SRX038601 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Myo.10.Input_control.AllCell.bed ...

File list: InP.Myo.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Myo.10.Input_control.AllCell mm9 Input control Input control Muscle SRX1482291,...66227,SRX695944 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Myo.10.Input_control.AllCell.bed ...

File list: InP.ALL.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.50.Input_control.AllCell dm3 Input control Input control All cell types SRX...948 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.ALL.50.Input_control.AllCell.bed ...

Experimental Evaluation of Pool Fire Suppression Performance of Sodium Leak Collection Tray in Open Air

International Nuclear Information System (INIS)

Parida, F.C.; Rao, P.M.; Ramesh, S.S.; Malarvizhi, B.; Gopalakrishnan, V.; Rao, E.H.V.M.; Kasinathan, N.; Kannan, S.E.

2006-01-01

In the event of sodium leakage from heat transfer circuits of fast breeder reactors (FBR), liquid sodium catches fire in ambient air leading to production of flame, smoke and heat. One of the passive fire protection methods involves immediate collection of the leaking sodium to a sodium hold-up vessel (SHV) covered with a sloping cover tray (SCT) having a few drain pipes and one vent pipe (as in Fig. 1). As soon as the liquid sodium falls on the sloping cover tray, gravity guides the sodium through drain pipes into the bottom tray in which self-extinction occurs due to oxygen starvation. This sodium fire protection equipment called leak collection tray (LCT) works without the intervention of an operator and external power source. A large number of LCTs are strategically arranged under the sodium circulating pipe lines in the FBR plants to serve as passive suppression devices. In order to test the efficacy of the LCT, four tests were conducted. Two tests were with LCT having three drain pipes and rest with one. In each experiment, nearly 40 kg of hot liquid sodium at 550 deg. C was discharged on the LCT in the open air. Continuous on-line monitoring of temperature at strategic locations (∼ 28 points) were carried out. Colour video-graphy was employed for taking motion pictures of various time-dependent events like sodium dumping, appearance of flame and release of smoke through vent pipes. After self-extinction of sodium fire, the LCT was allowed to cool overnight in an argon atmosphere. Solid samples of sodium debris in the SCT and SHV were collected by manual core drilling machine. The samples were subjected to chemical analysis for determination of unburnt and burnt sodium. The results of the four tests revealed an interesting feature: LCT with three drain pipes showed far lower sodium collection efficiency and much higher sodium combustion than that with just one drain pipe. Thermal fluctuations in temperature sensor located near the tip of the drain pipe have

Effects of long-term exposure on LDEF fastener assemblies

Science.gov (United States)

Spear, Steve; Dursch, Harry

1992-09-01

This presentation summarizes the Systems Special Investigations Group (SIG) findings from testing and analysis of fastener assemblies used on the Long Duration Exposure Facility (LDEF) structure, the tray mounting clamps, and by the various experimenters. The LDEF deintegration team and several experimenters noted severe fastener damage and hardware removal difficulties during post-flight activities. The System SIG has investigated all reported instances, and in all cases examined to date, the difficulties were attributed to galling during installation or post-flight removal. To date, no evidence of coldwelding was found. Correct selection of materials and lubricants as well as proper mechanical procedures is essential to ensure successful on-orbit or post-flight installation and removal of hardware.

File list: InP.Bld.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bld.10.Input_control.AllCell mm9 Input control Input control Blood SRX181865,SR...,SRX832474,SRX832475 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.10.Input_control.AllCell.bed ...

File list: InP.Myo.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Myo.50.Input_control.AllCell mm9 Input control Input control Muscle SRX262224,S...62124,SRX022849 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Myo.50.Input_control.AllCell.bed ...

File list: InP.ALL.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.50.Input_control.AllCell mm9 Input control Input control All cell types SRX...7314,ERX807291 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.ALL.50.Input_control.AllCell.bed ...

File list: InP.Utr.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Utr.05.Input_control.AllCell mm9 Input control Input control Uterus SRX129065,S...RX114726,SRX336292 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Utr.05.Input_control.AllCell.bed ...

File list: InP.Bld.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bld.05.Input_control.AllCell mm9 Input control Input control Blood SRX181866,SR...,SRX836257,SRX832475 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.05.Input_control.AllCell.bed ...

File list: InP.YSt.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.YSt.10.Input_control.AllCell sacCer3 Input control Input control Yeast strain S...,SRX211436 http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.YSt.10.Input_control.AllCell.bed ...

File list: InP.YSt.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.YSt.05.Input_control.AllCell sacCer3 Input control Input control Yeast strain S...,SRX211435 http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.YSt.05.Input_control.AllCell.bed ...

File list: InP.Bld.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bld.20.Input_control.AllCell mm9 Input control Input control Blood SRX181865,SR...,SRX209471,SRX021428 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.20.Input_control.AllCell.bed ...

File list: InP.Utr.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Utr.20.Input_control.AllCell mm9 Input control Input control Uterus SRX114726,S...RX129065,SRX336292 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Utr.20.Input_control.AllCell.bed ...

File list: InP.Brs.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Brs.10.Input_control.AllCell hg19 Input control Input control Breast SRX386756,...2,ERX371677,SRX1272812 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Brs.10.Input_control.AllCell.bed ...

File list: InP.YSt.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.YSt.20.Input_control.AllCell sacCer3 Input control Input control Yeast strain S...,SRX211436 http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.YSt.20.Input_control.AllCell.bed ...

File list: InP.Bld.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bld.50.Input_control.AllCell mm9 Input control Input control Blood SRX1287947,S...,SRX120230,SRX021428 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.50.Input_control.AllCell.bed ...

Combat Ration Network for Technology Implementation. Polymeric Tray Manufacturability, Part 2 (Short Term Project - STP1002B)

National Research Council Canada - National Science Library

Bruins, Henderikus

1999-01-01

.... Therefore, a second Polymeric Tray Manufacturability at the CORANET Demonstration Site at Rutgers University Food Manufacturing Technology Facility was conducted on June 9-10, 1998 to specifically address these issues...

File list: InP.Utr.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Utr.05.Input_control.AllCell hg19 Input control Input control Uterus SRX092571,...44717,SRX811390,SRX811387,SRX811388 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Utr.05.Input_control.AllCell.bed ...

File list: InP.ALL.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.10.Input_control.AllCell mm9 Input control Input control All cell types SRX...2625,SRX564564,SRX115361 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.ALL.10.Input_control.AllCell.bed ...

File list: InP.Lng.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lng.05.Input_control.AllCell mm9 Input control Input control Lung SRX062977,SRX...SRX213837,SRX213846,SRX213842 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Lng.05.Input_control.AllCell.bed ...

File list: InP.Emb.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Emb.50.Input_control.AllCell ce10 Input control Input control Embryo SRX027097,...331141,SRX982091,SRX331153,SRX331231 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/InP.Emb.50.Input_control.AllCell.bed ...

File list: InP.Gon.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Gon.50.Input_control.AllCell mm9 Input control Input control Gonad SRX332361,SR...89,SRX099892,SRX099895 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Gon.50.Input_control.AllCell.bed ...

File list: InP.Utr.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Utr.50.Input_control.AllCell hg19 Input control Input control Uterus SRX117811,...50615,SRX150616,SRX863779,SRX389283 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Utr.50.Input_control.AllCell.bed ...

File list: InP.Gon.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Gon.05.Input_control.AllCell mm9 Input control Input control Gonad SRX332361,SR...03,SRX591716,SRX555507 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Gon.05.Input_control.AllCell.bed ...

File list: InP.Lng.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lng.10.Input_control.AllCell mm9 Input control Input control Lung SRX213845,SRX...RX213842,SRX213846,SRX1528654 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Lng.10.Input_control.AllCell.bed ...

File list: InP.Dig.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Dig.05.Input_control.AllCell mm9 Input control Input control Digestive tract SR...X885797,SRX885796,SRX885801 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Dig.05.Input_control.AllCell.bed ...

File list: InP.ALL.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.05.Input_control.AllCell sacCer3 Input control Input control All cell types...ERX462363,ERX433715 http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.ALL.05.Input_control.AllCell.bed ...

File list: InP.Gon.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Gon.10.Input_control.AllCell mm9 Input control Input control Gonad SRX332361,SR...89,SRX076065,SRX555507 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Gon.10.Input_control.AllCell.bed ...

File list: InP.Dig.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Dig.50.Input_control.AllCell mm9 Input control Input control Digestive tract SR...X193725,SRX885789,SRX376973 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Dig.50.Input_control.AllCell.bed ...

Sintesis Bahan Dasar Tibial Tray Berbasis HDPE Yang Diperkuat Dengan Iradiasi Gamma

Directory of Open Access Journals (Sweden)

Sulistioso Giat S.

2014-04-01

Full Text Available Tibial tray yang sudah komersil dibuat dari Polimer Ultra High Molecular Weight Polyethylene (UHMWPE tetapi harganya sangat mahal. Oleh karena itu pada penelitian ini digunakan polimer High Density Polyethylene (HDPE untuk pembuatan tibial tray karena harganya yang lebih murah dan memiliki kemiripan sifat dengan UHMWPE. HDPE dibuat dengan dua metode, yaitu metode hot press dan pemanasan tanpa tekanan (PTT. UHMWPE dengan metode hot press digunakan sebagai pembanding. Metode hot press dilakukan pada suhu 180 °C dan diberi tekanan sebesar 200 kg/cm2. Sedangkan metode pemanasan tanpa tekanan (PTT dilakukan di dalam oven pada suhu 180°C. Film tipis UHMWPE dan sampel HDPE yang dihasilkan dari kedua metode tersebut, kemudian diiradiasi sinar gamma dengan variasi dosis 0, 100, 200, 300 dan 500 kGy. Karakterisasi mencakup analisis morfologi dengan Scanning Electron Microscope (SEM, uji kekerasan, kekuatan tarik, dan derajat kristalinitas. Semakin tinggi dosis radiasi, maka kekerasan dan derajat kristalinitas semakin meningkat, tetapi kekuatan tarik semakin menurun. Dosis radiasi untuk sampel HDPE yang optimum , adalah 100 kGy untuk HDPE yang dibuat dengan metoda hot press, pada kondisi ini HDPE mempunyai kekuatan mekanik mendekati nilai kekuatan mekanik UHMWPE, sedangkan HDPE yang dibuat dengan metode PTT kekuatan mekaniknya masih dibawah kekuatan mekanik HDPE yang dibuat dengan metoda hot press 

File list: InP.Unc.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.10.Input_control.AllCell ce10 Input control Input control Unclassified SRX0...03829,SRX003828,SRX003826,SRX003827,SRX560679 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/InP.Unc.10.Input_control.AllCell.bed ...

File list: InP.Adl.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Adl.50.Input_control.AllCell dm3 Input control Input control Adult SRX181432,SR...15625,SRX507386,SRX390503,SRX016141 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Adl.50.Input_control.AllCell.bed ...

File list: InP.Neu.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Neu.50.Input_control.AllCell mm9 Input control Input control Neural SRX109476,S...X685922,SRX145797,SRX150263,SRX150261 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Neu.50.Input_control.AllCell.bed ...

File list: InP.Adl.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Adl.20.Input_control.AllCell dm3 Input control Input control Adult SRX264598,SR...07394,SRX970862,SRX215623,SRX215627 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Adl.20.Input_control.AllCell.bed ...

File list: InP.Oth.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Oth.50.Input_control.AllCell hg19 Input control Input control Others SRX253236,...RX188949,SRX189956,SRX080334,SRX080429 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Oth.50.Input_control.AllCell.bed ...

File list: InP.Oth.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Oth.10.Input_control.AllCell mm9 Input control Input control Others SRX022481,S...,SRX1365335,SRX228661,SRX388797,SRX957693 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Oth.10.Input_control.AllCell.bed ...

File list: InP.Epd.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Epd.50.Input_control.AllCell hg19 Input control Input control Epidermis SRX7005...65,SRX189959,SRX080381,SRX189950,SRX099054 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Epd.50.Input_control.AllCell.bed ...

File list: InP.Unc.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.20.Input_control.AllCell hg19 Input control Input control Unclassified SRX1...3292,ERX026985,SRX1094495,SRX545955,SRX212467 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Unc.20.Input_control.AllCell.bed ...

File list: InP.Unc.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.05.Input_control.AllCell hg19 Input control Input control Unclassified SRX5...5953,SRX063292,SRX1094492,SRX012413,ERX026985 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Unc.05.Input_control.AllCell.bed ...

File list: InP.Unc.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.10.Input_control.AllCell hg19 Input control Input control Unclassified SRX1...94492,SRX063292,SRX212465,SRX012413,ERX026985 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Unc.10.Input_control.AllCell.bed ...

File list: InP.Lar.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lar.20.Input_control.AllCell dm3 Input control Input control Larvae SRX040614,S...457599,SRX1426944,SRX1426946,SRX1426948 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Lar.20.Input_control.AllCell.bed ...

File list: InP.Epd.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Epd.10.Input_control.AllCell hg19 Input control Input control Epidermis SRX2000...54,SRX189959,SRX080365,SRX573182,SRX573176 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Epd.10.Input_control.AllCell.bed ...

File list: InP.Neu.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Neu.05.Input_control.AllCell mm9 Input control Input control Neural SRX236086,S...X668239,ERX513118,SRX150263,ERX513117 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Neu.05.Input_control.AllCell.bed ...

File list: InP.ALL.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.20.Input_control.AllCell sacCer3 Input control Input control All cell types...2392,ERX433647,ERX433677,ERX433717 http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.ALL.20.Input_control.AllCell.bed ...

File list: InP.Oth.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Oth.20.Input_control.AllCell hg19 Input control Input control Others SRX253236,...X512178,SRX512179,SRX1074575,SRX371462 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Oth.20.Input_control.AllCell.bed ...

File list: InP.Neu.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Neu.20.Input_control.AllCell mm9 Input control Input control Neural SRX109476,S...X513118,SRX150261,ERX513117,SRX150263 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Neu.20.Input_control.AllCell.bed ...

File list: InP.Unc.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.10.Input_control.AllCell sacCer3 Input control Input control Unclassified E...2438,ERX462370,ERX433651,ERX433709 http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.Unc.10.Input_control.AllCell.bed ...

File list: InP.Unc.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.05.Input_control.AllCell ce10 Input control Input control Unclassified SRX0...03829,SRX003827,SRX003828,SRX003826,SRX560679 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/InP.Unc.05.Input_control.AllCell.bed ...

File list: InP.Unc.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Unc.20.Input_control.AllCell ce10 Input control Input control Unclassified SRX0...03827,SRX003826,SRX560679,SRX003828,SRX003829 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/InP.Unc.20.Input_control.AllCell.bed ...

File list: InP.Oth.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Oth.10.Input_control.AllCell hg19 Input control Input control Others SRX668215,...RX371462,SRX376724,SRX512177,SRX512179 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Oth.10.Input_control.AllCell.bed ...

File list: InP.Adl.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Adl.05.Input_control.AllCell dm3 Input control Input control Adult SRX220301,SR...81442,SRX215625,SRX215627,SRX970862 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Adl.05.Input_control.AllCell.bed ...

Ceramic fiber blanket wrap for fire protection of cable trays and conduits

International Nuclear Information System (INIS)

Chaille, C.E.; Reiman, R.J.

1980-01-01

In some areas of nuclear power plants, cables of redundant electrical systems, which are necessary for the safe shutdown of the reactor, are in close proximity. If a fire should occur in one of these areas, both electrical systems could be destroyed before the fire is extinguished and control of the reactor may be lost. A ceramic fiber blanket was evaluated as a fire protective wrap around cable trays and conduits. 2 refs

File list: InP.NoD.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.05.Input_control.AllCell dm3 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.NoD.05.Input_control.AllCell.bed ...

File list: InP.NoD.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.20.Input_control.AllCell dm3 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.NoD.20.Input_control.AllCell.bed ...

File list: InP.NoD.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.05.Input_control.AllCell sacCer3 Input control Input control No description... http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.NoD.05.Input_control.AllCell.bed ...

File list: InP.NoD.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.50.Input_control.AllCell hg19 Input control Input control No description ht...tp://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.NoD.50.Input_control.AllCell.bed ...

File list: InP.NoD.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.50.Input_control.AllCell sacCer3 Input control Input control No description... http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/InP.NoD.50.Input_control.AllCell.bed ...

File list: InP.NoD.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.50.Input_control.AllCell dm3 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.NoD.50.Input_control.AllCell.bed ...

File list: InP.NoD.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.05.Input_control.AllCell hg19 Input control Input control No description ht...tp://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.NoD.05.Input_control.AllCell.bed ...

File list: InP.NoD.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.20.Input_control.AllCell mm9 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.NoD.20.Input_control.AllCell.bed ...

File list: InP.NoD.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.05.Input_control.AllCell mm9 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.NoD.05.Input_control.AllCell.bed ...

File list: InP.NoD.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.10.Input_control.AllCell dm3 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.NoD.10.Input_control.AllCell.bed ...

File list: InP.Brs.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Brs.05.Input_control.AllCell mm9 Input control Input control Breast SRX483143,S...ERX200438,SRX1078980,ERX200398,ERX200402,SRX396750 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Brs.05.Input_control.AllCell.bed ...

File list: InP.Lar.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lar.05.Input_control.AllCell dm3 Input control Input control Larvae SRX645428,S...287678,SRX1426944,SRX1426946,SRX1426948,SRX1426950 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Lar.05.Input_control.AllCell.bed ...

File list: InP.ALL.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.05.Input_control.AllCell ce10 Input control Input control All cell types SR...6,SRX188620,SRX005633,SRX560679,SRX015099 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/InP.ALL.05.Input_control.AllCell.bed ...

File list: InP.Pan.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Pan.05.Input_control.AllCell hg19 Input control Input control Pancreas SRX19030...0794,SRX188948,SRX190029,SRX199860,SRX026707,SRX825393 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Pan.05.Input_control.AllCell.bed ...

File list: InP.CDV.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.CDV.05.Input_control.AllCell hg19 Input control Input control Cardiovascular SR...SRX190068,SRX220067,SRX190094,SRX080409,SRX190090,SRX699736 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.CDV.05.Input_control.AllCell.bed ...

File list: InP.Brs.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Brs.20.Input_control.AllCell mm9 Input control Input control Breast SRX483143,S...SRX396745,SRX403484,SRX1078982,SRX031066,SRX031214 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Brs.20.Input_control.AllCell.bed ...

File list: InP.Pup.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Pup.50.Input_control.AllCell dm3 Input control Input control Pupae SRX016163,SR...X016167,SRX016169,SRX016164,SRX016165,SRX016168 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Pup.50.Input_control.AllCell.bed ...

File list: InP.CDV.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.CDV.10.Input_control.AllCell hg19 Input control Input control Cardiovascular SR...SRX190094,SRX190090,SRX189947,SRX080435,DRX021454,SRX699736 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.CDV.10.Input_control.AllCell.bed ...

File list: InP.Pan.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Pan.10.Input_control.AllCell hg19 Input control Input control Pancreas SRX19030...8948,SRX825393,SRX199860,SRX190029,SRX026707,SRX375320 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Pan.10.Input_control.AllCell.bed ...

File list: InP.Oth.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Oth.05.Input_control.AllCell mm9 Input control Input control Others SRX022481,S...1,SRX957691,SRX388797,SRX957693,SRX024355 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Oth.05.Input_control.AllCell.bed ...

File list: InP.Pan.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Pan.20.Input_control.AllCell hg19 Input control Input control Pancreas SRX34080...0803,SRX340794,SRX199860,SRX190029,SRX026707,SRX375320 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Pan.20.Input_control.AllCell.bed ...

File list: InP.Brs.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Brs.10.Input_control.AllCell mm9 Input control Input control Breast SRX213411,S...,ERX200429,ERX200402,SRX396747,SRX396750,SRX403487 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Brs.10.Input_control.AllCell.bed ...

File list: InP.Pup.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Pup.10.Input_control.AllCell dm3 Input control Input control Pupae SRX016165,SR...X016163,SRX016164,SRX016169,SRX016168,SRX016167 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.Pup.10.Input_control.AllCell.bed ...

File list: InP.Brs.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Brs.50.Input_control.AllCell mm9 Input control Input control Breast SRX483143,S...SRX403484,SRX1078982,SRX031066,SRX031214,SRX697687 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Brs.50.Input_control.AllCell.bed ...

File list: InP.Oth.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Oth.20.Input_control.AllCell mm9 Input control Input control Others SRX022481,S...1,SRX957691,SRX378545,SRX378544,SRX957693 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Oth.20.Input_control.AllCell.bed ...

Evaluation of the Thickness and Oxygen Transmission Rate before and after Thermoforming Mono- and Multi-layer Sheets into Trays with Variable Depth

Directory of Open Access Journals (Sweden)

Mieke Buntinx

2014-12-01

Full Text Available During thermoforming, plastic sheets are heated and subsequently deformed through the application of mechanical stretching and/or pressure. This process directly impacts sheet properties such as material thickness in walls, corners, and bottom, crystallinity in the constituent layers, and particularly the oxygen gas permeability. The aim of this study was to quantify the impact of thermoforming on thickness and oxygen transmission rate (OTR of selected packaging materials (polypropylene (PP; PP/ethylene-vinyl alcohol co-polymer/PP (PP/EVOH/PP; polystyrene/EVOH/polyethylene (PS/EVOH/PE; amorphous polyethylene terephtalate/PE (APET/PE; APET/PE/EVOH/PE; polyamide/PE (PA/PE; and (PE/PA/EVOH/PA/PE. These materials were extruded in two different thicknesses and thermoformed into trays with the same top dimensions and variable depths of 25, 50, and/or 75 mm and a 50 mm tray with a variable radius of the corners. The distribution of the material thickness in the trays was visualized, showing the locations that were most affected by the deep drawn process. The OTR results indicate that the calculated OTR, based on a homogeneous material distribution, can be used as a rough approximation of the measured OTR. However, detailed analysis of crystallization and unequal thinning, which is also related to the tray design, remains necessary to explain the deviation of the measured OTR as compared to the predicted one.

File list: InP.EmF.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.EmF.50.Input_control.AllCell mm9 Input control Input control Embryonic fibrobla...363,SRX115361 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.EmF.50.Input_control.AllCell.bed ...

File list: InP.EmF.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.EmF.05.Input_control.AllCell mm9 Input control Input control Embryonic fibrobla...367,SRX115361 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.EmF.05.Input_control.AllCell.bed ...

File list: InP.EmF.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.EmF.20.Input_control.AllCell mm9 Input control Input control Embryonic fibrobla...367,SRX115361 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.EmF.20.Input_control.AllCell.bed ...

Benchmark assemblies of the Los Alamos critical assemblies facility

International Nuclear Information System (INIS)

Dowdy, E.J.

1986-01-01

Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described. (author)

Benchmark assemblies of the Los Alamos Critical Assemblies Facility

International Nuclear Information System (INIS)

Dowdy, E.J.

1985-01-01

Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described

Benchmark assemblies of the Los Alamos critical assemblies facility

International Nuclear Information System (INIS)

Dowdy, E.J.

1985-01-01

Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described

Scanning electron microscope/energy dispersive x ray analysis of impact residues on LDEF tray clamps

Science.gov (United States)

Bernhard, Ronald P.; Durin, Christian; Zolensky, Michael E.

1992-01-01

To better understand the nature of particulates in low-Earth orbit (LEO), and their effects on spacecraft hardware, we are analyzing residues found in impacts on the Long Duration Exposure Facility (LDEF) tray clamps. LDEF experiment trays were held in place by 6 to 8 chromic-anodized aluminum (6061-T6) clamps that were fastened to the spacecraft frame using three stainless steel hex bolts. Each clamp exposed an area of approximately 58 sq cm (4.8 cm x 12.7 cm x .45 cm, minus the bolt coverage). Some 337 out of 774 LDEF tray clamps were archived at JSC and are available through the Meteoroid & Debris Special Investigation Group (M&D SIG). Optical scanning of clamps, starting with Bay/Row A01 and working toward H25, is being conducted at JSC to locate and document impacts as small as 40 microns. These impacts are then inspected by Scanning Electron Microscopy/Energy Dispersive X-ray Analysis (SEM/EDXA) to select those features which contain appreciable impact residue material. Based upon the composition of projectile remnants, and using criteria developed at JSC, we have made a preliminary discrimination between micrometeoroid and space debris residue-containing impact features. Presently, 13 impacts containing significant amounts of unmelted and semi-melted micrometeoritic residues were forwarded to Centre National d'Etudes Spatiales (CNES) in France. At the CNES facilities, the upgraded impacts were analyzed using a JEOL T330A SEM equipped with a NORAN Instruments, Voyager X-ray Analyzer. All residues were quantitatively characterized by composition (including oxygen and carbon) to help understand interplanetary dust as possibly being derived from comets and asteroids.

File list: InP.Lng.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lng.20.Input_control.AllCell hg19 Input control Input control Lung SRX502813,SR...1772,SRX734236,SRX188957,SRX1004561,SRX497257,SRX497258 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Lng.20.Input_control.AllCell.bed ...

File list: InP.Dig.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Dig.10.Input_control.AllCell hg19 Input control Input control Digestive tract S...RX155777,SRX077858,SRX863785,SRX543682,SRX286206,SRX543691 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Dig.10.Input_control.AllCell.bed ...

File list: InP.Dig.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Dig.50.Input_control.AllCell hg19 Input control Input control Digestive tract S...RX155744,SRX612781,SRX543681,SRX101310,SRX648244,SRX863785 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Dig.50.Input_control.AllCell.bed ...

File list: InP.Dig.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Dig.20.Input_control.AllCell hg19 Input control Input control Digestive tract S...X077858,SRX286206,SRX124697,SRX1183967,SRX124698,SRX543691 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Dig.20.Input_control.AllCell.bed ...

File list: InP.Lng.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lng.10.Input_control.AllCell hg19 Input control Input control Lung SRX502813,SR...74812,SRX016558,SRX734236,SRX038682,SRX497257,SRX497258 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Lng.10.Input_control.AllCell.bed ...

File list: InP.Lng.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lng.05.Input_control.AllCell hg19 Input control Input control Lung SRX502813,SR...88957,SRX093320,SRX038682,SRX502807,SRX497258,SRX497257 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Lng.05.Input_control.AllCell.bed ...

File list: InP.ALL.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.50.Input_control.AllCell hg19 Input control Input control All cell types SR...038682,SRX389283,SRX863785,SRX1029468,SRX155724,SRX038907 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.ALL.50.Input_control.AllCell.bed ...

File list: InP.Lng.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Lng.50.Input_control.AllCell hg19 Input control Input control Lung SRX502813,SR...89952,SRX080360,SRX734236,SRX038683,SRX093320,SRX038682 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Lng.50.Input_control.AllCell.bed ...

File list: InP.Dig.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Dig.05.Input_control.AllCell hg19 Input control Input control Digestive tract S...RX124694,SRX543691,SRX543683,SRX367635,SRX286206,SRX543682 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Dig.05.Input_control.AllCell.bed ...

The influence of gamma radiation on HDPE properties for tibial tray

International Nuclear Information System (INIS)

Sulistioso, G.S.; Dewi, R.K.; Maria, C.P.; Nada, M.

2012-01-01

A research on HDPE as tibial tray in total knee joint replacement surgery has been done. The aims of this research were to characterize the influence of gamma radiation on chemical, and mechanical properties on HDPE is made by using hot press method then irradiated with various doses of gamma rays of 0 kGy, 25 kGy, 50 kGy, 75 kGy, 100 kGy, 125 kGy, and 150 kGy at a dose rate 9 kGy/h. The irradiated HDPE were tested for their chemical, and mechanical properties. The chemical properties test, involve crosslinking and free radicals. The mechanical properties test, involve hardness, tensile strength, and elongation at break. The results showed that gamma radiation from IRKA IV th category can enhance the, chemical properties of HDPE in terms of percentage and number of radical crosslinking and mechanical properties of HDPE in terms of hardness, tensile strength and elongation at break with different changes from the initial state before radiation also the optimum dose to obtain better physical, chemical, and mechanical properties of HDPE, crosslinking percentage at 99.71%; height of radical peroxide curve at 13 cm; hardness (shore A) at 94.33; modulus of elasticity at 1113.03 N/mm 2 ; yield stress at 26.38 N/mm 2 ; tensile strength at 31.11 N/mm 2 ; and elongation at break at 440.37%, so that HDPE can be used as tibial tray. (author)

Neutron coincidence counter for MOX fuel pins in storage trays: users' manual

International Nuclear Information System (INIS)

Cowder, L.; Menlove, H.

1982-08-01

The neutron coincidence counter for measurement of mixed-oxide fuel pins in storage trays is described. The special detector head has been designed so that the detectors, high-voltage junction boxes, and electronics are interchangeable with those of the high-level neutron coincidence counter system. This manual describes the system components and the operation and maintenance of the counter. The counter was developed at Los Alamos National Laboratory for in-plant inspection applications by the International Atomic Energy Agency

Modeling Separation Dynamics in a Multi-Tray Bio-Ethanol Distillation Column

DEFF Research Database (Denmark)

Løhndorf, Petar Durdevic; Pedersen, Simon; Yang, Zhenyu

2015-01-01

the product quality and energy consumption in a typical bio-ethanol distillation column is proposed in this paper. The proposed model is derived based on mass and energy balance principles, with an empirical model of the evaporation dynamics of liquids on column trays. The model parameters are identified......The high energy consumption of popularly used distillation columns has motivated development of energytracking dynamic models with the ultimate objective for potential better energy and quality control of these separation facilities. A dynamic model being able to explicitly describe both...

File list: InP.Adl.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Adl.05.Input_control.AllCell ce10 Input control Input control Adult SRX005630,S...RX080064,SRX323687,SRX1388754,SRX146417,SRX012296,SRX012299,SRX005633 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/InP.Adl.05.Input_control.AllCell.bed ...

File list: InP.Plc.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Plc.20.Input_control.AllCell mm9 Input control Input control Placenta SRX112971...02,SRX404310,SRX1072160,SRX871507,SRX192097,SRX192098,SRX192099,SRX204148 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Plc.20.Input_control.AllCell.bed ...

File list: InP.Gon.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Gon.10.Input_control.AllCell hg19 Input control Input control Gonad SRX1002699,...SRX663452,SRX1002710,SRX1002709,SRX1091823,SRX663439,SRX663445,SRX663442 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Gon.10.Input_control.AllCell.bed ...

File list: InP.Spl.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Spl.10.Input_control.AllCell mm9 Input control Input control Spleen ERX662629,E...242,ERX662616,SRX701169,SRX701170,SRX701168,ERX662615,ERX662625 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Spl.10.Input_control.AllCell.bed ...

File list: InP.Gon.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Gon.50.Input_control.AllCell hg19 Input control Input control Gonad SRX1002699,...SRX663452,SRX1002710,SRX1002709,SRX1091823,SRX663439,SRX663445,SRX663442 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Gon.50.Input_control.AllCell.bed ...

File list: InP.Gon.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Gon.20.Input_control.AllCell hg19 Input control Input control Gonad SRX1002699,...SRX663452,SRX1002710,SRX1002709,SRX663439,SRX663445,SRX1091823,SRX663442 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Gon.20.Input_control.AllCell.bed ...

File list: InP.Plc.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Plc.05.Input_control.AllCell mm9 Input control Input control Placenta SRX344647...160,SRX204147,SRX404310,SRX871506,SRX871507,SRX192098,SRX192097,SRX192099 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Plc.05.Input_control.AllCell.bed ...

File list: InP.Spl.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Spl.20.Input_control.AllCell mm9 Input control Input control Spleen ERX662629,E...626,ERX662620,SRX701168,SRX701169,SRX701170,ERX662615,ERX662625 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Spl.20.Input_control.AllCell.bed ...

File list: InP.Plc.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Plc.10.Input_control.AllCell mm9 Input control Input control Placenta SRX344648...310,SRX871506,SRX142911,SRX871507,SRX204148,SRX192098,SRX192097,SRX192099 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Plc.10.Input_control.AllCell.bed ...

File list: InP.Pan.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Pan.20.Input_control.AllCell mm9 Input control Input control Pancreas SRX188611...035142,SRX751762,SRX751759,SRX751765,SRX751768,SRX327162,SRX672452,SRX327163 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Pan.20.Input_control.AllCell.bed ...

File list: InP.Prs.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Prs.05.Input_control.AllCell hg19 Input control Input control Prostate SRX08452...RX882951,SRX334229,SRX047085,SRX248897,SRX315154,SRX315157,SRX120297,SRX540851 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Prs.05.Input_control.AllCell.bed ...

File list: InP.CDV.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.CDV.10.Input_control.AllCell mm9 Input control Input control Cardiovascular SRX...4,SRX373590,SRX1304811,SRX1304812,SRX377394,SRX377691,SRX275462,SRX275461,SRX066549 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.CDV.10.Input_control.AllCell.bed ...

File list: InP.Bon.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bon.10.Input_control.AllCell mm9 Input control Input control Bone SRX425483,ERX...RX211434,ERX211444,ERX211435,ERX211437,ERX211438,ERX211433,ERX211436,SRX963262 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bon.10.Input_control.AllCell.bed ...

File list: InP.Kid.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Kid.20.Input_control.AllCell hg19 Input control Input control Kidney SRX973437,...X968416,SRX1094507,SRX1094511,SRX1353404,SRX1094515,ERX513120,SRX114492,SRX170378 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Kid.20.Input_control.AllCell.bed ...

File list: InP.Kid.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Kid.10.Input_control.AllCell mm9 Input control Input control Kidney SRX804277,S...RX085456,SRX143808,SRX804276,SRX286402,SRX286403,SRX062965,SRX804278,SRX1050552 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Kid.10.Input_control.AllCell.bed ...

File list: InP.Prs.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Prs.20.Input_control.AllCell hg19 Input control Input control Prostate SRX53966...X306505,SRX475374,SRX540851,SRX475375,SRX1098753,SRX334229,SRX176071,SRX315154 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Prs.20.Input_control.AllCell.bed ...

File list: InP.Kid.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Kid.05.Input_control.AllCell hg19 Input control Input control Kidney SRX359412,...X1037589,SRX985312,SRX974385,SRX1094515,SRX003879,SRX1094507,SRX1094511,ERX513120 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Kid.05.Input_control.AllCell.bed ...

File list: InP.Kid.05.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Kid.05.Input_control.AllCell mm9 Input control Input control Kidney SRX062965,S...RX085456,SRX143808,SRX1050552,SRX286402,SRX804277,SRX804276,SRX286403,SRX804278 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Kid.05.Input_control.AllCell.bed ...

File list: InP.Kid.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Kid.20.Input_control.AllCell mm9 Input control Input control Kidney SRX804277,S...RX286402,SRX143808,SRX804276,SRX286403,SRX062965,SRX085456,SRX804278,SRX1050552 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Kid.20.Input_control.AllCell.bed ...

File list: InP.ALL.10.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.ALL.10.Input_control.AllCell dm3 Input control Input control All cell types SRX...,SRX215627,SRX390503,SRX1426952,SRX1426954,SRX1426944,SRX1426946,SRX681798,SRX1426948 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.ALL.10.Input_control.AllCell.bed ...

File list: InP.Kid.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Kid.50.Input_control.AllCell mm9 Input control Input control Kidney SRX804277,S...RX286402,SRX143808,SRX804276,SRX286403,SRX062965,SRX085456,SRX804278,SRX1050552 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Kid.50.Input_control.AllCell.bed ...

File list: InP.CDV.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.CDV.50.Input_control.AllCell mm9 Input control Input control Cardiovascular SRX...74,SRX517514,SRX373580,SRX320036,SRX320037,SRX1121694,SRX275462,SRX275461,SRX066549 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.CDV.50.Input_control.AllCell.bed ...

File list: InP.Bon.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bon.20.Input_control.AllCell mm9 Input control Input control Bone SRX425483,SRX...RX211444,ERX211434,ERX211433,ERX211443,ERX211437,ERX211435,SRX963262,ERX211436 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bon.20.Input_control.AllCell.bed ...

File list: InP.CDV.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.CDV.20.Input_control.AllCell mm9 Input control Input control Cardiovascular SRX...75,SRX373609,SRX373610,SRX373590,SRX320036,SRX275461,SRX275462,SRX066549,SRX1121694 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.CDV.20.Input_control.AllCell.bed ...

File list: InP.Kid.50.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Kid.50.Input_control.AllCell hg19 Input control Input control Kidney SRX973437,...,SRX114492,SRX170378,SRX691805,SRX080441,SRX1293074,SRX326417,SRX684265,SRX684263 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Kid.50.Input_control.AllCell.bed ...

Nuclear fuel pellet collating system and method

International Nuclear Information System (INIS)

Rieben, S.L.; Kugler, R.W.; Scherpenberg, J.J.; Wiersema, D.T.

1990-01-01

This patent describes a method of collating nuclear fuel pellets. It comprises: supporting a plurality of pellet supply trays and a plurality of pellet storage trays at a tray positioning station. Each of the supply trays containing in at least one row thereon a plurality of nuclear fuel pellets of an enrichment different from the enrichment pellets on at least some other of the supply trays; transferring one pellet supply tray from the tray positioning station and disposing the same at an input station of a pellet collating line; transferring one pellet storage tray from the tray positioning station and disposing the same at an output station of the pellet collating line; sweeping pellets in the at least one row thereof from the one pellet supply tray onto a work station of the pellet collating line located between the input and output stations thereof; measuring a desired length of pellets in the at least one row on the work station and separating the measured desired length of pellets from the remaining pellets, if any, in the row thereof; sweeping the remaining pellets, if any, in the row from the work station back onto the one pellet supply tray; transferring the one pellet supply tray and remaining pellets, if any, back to the tray positioning station; sweeping the measured desired length of pellets from the work station onto the one pellet storage tray; and transferring the one pellet storage tray and measured desired length of pellets back to the tray positioning station

View of the moving head of the gantry machine and the working area containingthe supply and assembly platforms (trays in green).

CERN Multimedia

Alan Honma

1999-01-01

The robotic assembly machine consists of the gantry positioning systemoutfitted with pickup tooling heads and camera+microscope for accurateposition measurements. The procedure is to place the components onthe working platforms and the machine applies glue, picks and placesthe silicon sensors and front-end hybrids onto the frames. The components are held in place by vacuum to prevent movement untilthe glue has cured. Up to four modules can be assembled at one time.The platforms are removable allowing assembly to continue on a newset of modules.

Assessment of the burning behavior of protected and unprotected cables and cable trays in nuclear installations using small- and large-scale experiments

Energy Technology Data Exchange (ETDEWEB)

Siemon, Matthias; Riese, Olaf; Zehfuss, Jochen [Technische Univ. Braunschweig (Germany). Inst. fuer Baustoffe, Massivbau und Brandschutz (iBMB)

2015-12-15

Electric installations and cables are a main fire risk source in industrial buildings and power plants. In general, cables and cable systems are associated with flash-over phenomena due to pyrolysis of fuel gases induced by the heat of an adjacent fire, fire spread along cable trays affecting additional areas besides the fire origin, being an ignition source due to malfunction. If burning, cables can emit large amounts of smoke and toxic products affecting occupants as well as the long-term functionality of structure and installations. Paying attention to these risks has led to the development of fire retardant non-corrosive (non-halogenated) cables which are qualified to reduce the individual or all of the risks mentioned. For existing installations in industrial buildings and power plants with halogenated cables, different protection measures are available and widely applied retroactively. Important protective measures are intumescent or ablative coatings, cable casings and bindings. For qualification of the effects of the protection measures, small-scale tests investigating a single cable specimen as well as large-scale cable tray test setups have been developed and carried out in the last 20 years at iBMB. In this paper, these test results are analysed regarding their effects on the heat release, ignition time and fire spread over cable trays. Furthermore, national and international research projects have investigated the burning behaviour of different cable types, tray installations, tray loading and spacing and ventilation conditions. As a conclusion, the main outcomes of past researches are summarized. Influence factors (e.g. pre-heating due to high power utilization, influence of cable aging) which have not been accounted for in detail are emphasized. The modelling of unprotected cables has been internationally studied in recent years. For future applications, the question of applicability of recently developed sub-models on the fire behaviour of protected

Comparison of efficacy of tray-delivered carbamide and hydrogen peroxide for at-home bleaching: a systematic review and meta-analysis.

Science.gov (United States)

Luque-Martinez, Issis; Reis, Alessandra; Schroeder, Marcos; Muñoz, Miguel Angel; Loguercio, Alessandro D; Masterson, Danielle; Maia, Lucianne C

2016-09-01

The aim of the study was to compare the color change produced by tray-delivered carbamide peroxide [CP] versus hydrogen peroxide products [HP] for at-home bleaching through a systematic review and meta-analysis. MEDLINE via PubMeb, Scopus, Web of Science, Latin American and Caribbean Health Sciences Literature database (LILACS), Brazilian Library in Dentistry (BBO), and Cochrane Library and Grey literature were searched without restrictions. The abstracts of the International Association for Dental Research (IADR) and unpublished and ongoing trial registries were also searched. Dissertations and theses were explored using the ProQuest Dissertations and Periodicos Capes Theses databases. We included randomized clinical trials that compared tray-delivered CP versus HP for at-home dental bleaching. The color change in shade guide units (SGU) and ΔE were the primary outcomes, and tooth sensitivity and gingival irritation were the secondary outcomes. The risk of bias tool of the Cochrane Collaboration was used for quality assessment. After duplicate removal, 1379 articles were identified. However, only eight studies were considered to be at "low" risk of bias in the key domains of the risk bias tool and they were included in the analysis. For ΔE, the standardized mean difference was -0.45 (95 % CI -0.69 to -0.21), which favored tray-delivered CP products (p whitening efficacy than HP-based products in terms of ΔE, but they were similar in terms of ΔSGU. Both whitening systems demonstrated equal level of gingival irritation and tooth sensitivity. Tray-delivered CP gels have a slightly better whitening efficacy than HP-based products in terms of ΔE. This should be interpreted with caution as the data of ΔSGU did not show statistical difference between the products.

Reprocessing input data validation

International Nuclear Information System (INIS)

Persiani, P.J.; Bucher, R.G.; Pond, R.B.; Cornella, R.J.

1990-01-01

The Isotope Correlation Technique (ICT), in conjunction with the gravimetric (Pu/U ratio) method for mass determination, provides an independent verification of the input accountancy at the dissolver or accountancy stage of the reprocessing plant. The Isotope Correlation Technique has been applied to many classes of domestic and international reactor systems (light-water, heavy-water, graphite, and liquid-metal) operating in a variety of modes (power, research, production, and breeder), and for a variety of reprocessing fuel cycle management strategies. Analysis of reprocessing operations data based on isotopic correlations derived for assemblies in a PWR environment and fuel management scheme, yielded differences between the measurement-derived and ICT-derived plutonium mass determinations of (-0.02 ± 0.23)% for the measured U-235 and (+0.50 ± 0.31)% for the measured Pu-239, for a core campaign. The ICT analyses has been implemented for the plutonium isotopics in a depleted uranium assembly in a heavy-water, enriched uranium system and for the uranium isotopes in the fuel assemblies in light-water, highly-enriched systems. 7 refs., 5 figs., 4 tabs

Nitrogen deposition and its contribution to nutrient inputs to intensively managed agricultural ecosystems.

Science.gov (United States)

He, Chun-E; Wang, Xin; Liu, Xuejun; Fangmeier, Andreas; Christie, Peter; Zhang, Fusuo

2010-01-01

Interest in nitrogen inputs via atmospheric deposition to agricultural ecosystems has increased recently, especially on the North China Plain because of extremely intensive agricultural systems and rapid urbanization in this region. Nitrogen deposition may make a significant contribution to crop N requirements but may also impose a considerable nutrient burden on the environment in general. We quantified total N deposition at two locations, Dongbeiwang near Beijing and Quzhou in Hebei province, over a two-year period from 2005 to 2007 using an 15N tracer method, the integrated total N input (ITNI) system. Total airborne N inputs to a maize wheat rotation system at both locations ranged from 99 to 117 kg N x ha(-1) x yr(-1), with higher N deposition during the maize season (57-66 kg N/ha) than the wheat season (42-51 kg N/ha). Plant available N from deposition for maize and wheat was about 52 kg N x ha(-1) x yr(-1), accounting for 50% of the total N deposition or 31% of total N uptake by the two crop species. In addition, a correction factor was derived for the maize season to adjust values obtained from small pots (0.057 m2) compared with field trays (0.98 m2) because of higher plant density in the pots. The results indicate that atmospheric N deposition is a very important N input and must be taken into account when calculating nutrient budgets in very intensively managed agricultural ecosystems.

A simple method for fabricating custom sectional impression trays for making definitive impressions in patients with microstomia

OpenAIRE

Bachhav, Vinay Chila; Aras, Meena Ajay

2012-01-01

Objective: A maximum mouth opening that is smaller than the size of a complete denture can make prosthetic treatment challenging. This article describes a simple technique used to fabricate maxillary and mandibular custom sectional impression trays for making definitive impressions in patients with microstomia.

Pressure dynamics in the trays caused by differences of the various impression materials and thickness of the relief in the maxillary edentulous model.

Science.gov (United States)

Iwasaki, Masatoshi; Kawara, Misao; Inoue, Sayumi; Komiyama, Osamu; Iida, Takashi; Asano, Takashi

2016-04-01

The purpose of this study is to compare the pressure dynamics in the trays caused by differences in the various impression materials and in the thickness of the relief provided for the trays. In this study, two types of polyvinylsiloxane elastomers, one type of polyether elastomer and one type of alginate impression material were used. Pressure sensors were embedded at eight locations in a model of an edentulous maxilla, and used a simulation model covered with a pseudomucosa. For each impression material, the measurement was performed five times for each of the three types of trays, and the mean values were determined. Statistical analysis was carried out using one-way analysis of variance and the Tukey's HDS method, and the various pressure sensor values for each of the impression materials were compared 10s and 20s after the start of the measurement. Additionally, we compared differences among the three types of trays after 20s. The pressure values for sensors placed in the relief region tended to become uniform. Furthermore, we saw a tendency for the pressure to increase at the alveolar crests of the first molars on the left and right and at the posterior border of the palate, all of which support the denture, when relief was provided. The above results suggest that making the final impression for the denture using the selective pressure technique, with consideration given to the pressure dynamic, may lead to a good outcome in terms of preservation of the alveolar ridge. Copyright © 2015 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Sound absorption study on acoustic panel from kapok fiber and egg tray

Science.gov (United States)

Kaamin, Masiri; Mahir, Nurul Syazwani Mohd; Kadir, Aslila Abd; Hamid, Nor Baizura; Mokhtar, Mardiha; Ngadiman, Norhayati

2017-12-01

Noise also known as a sound, especially one that is loud or unpleasant or that causes disruption. The level of noise can be reduced by using sound absorption panel. Currently, the market produces sound absorption panel, which use synthetic fibers that can cause harmful effects to the health of consumers. An awareness of using natural fibers from natural materials gets attention of some parties to use it as a sound absorbing material. Therefore, this study was conducted to investigate the potential of sound absorption panel using egg trays and kapok fibers. The test involved in this study was impedance tube test which aims to get sound absorption coefficient (SAC). The results showed that there was good sound absorption at low frequency from 0 Hz up to 900 Hz where the maximum absorption coefficient was 0.950 while the maximum absorption at high frequencies was 0.799. Through the noise reduction coefficient (NRC), the material produced NRC of 0.57 indicates that the materials are very absorbing. In addition, the reverberation room test was carried out to get the value of reverberation time (RT) in unit seconds. Overall this panel showed good results at low frequencies between 0 Hz up to 1500 Hz. In that range of frequency, the maximum reverberation time for the panel was 3.784 seconds compared to the maximum reverberation time for an empty room was 5.798 seconds. This study indicated that kapok fiber and egg tray as the material of absorption panel has a potential as environmental and cheap products in absorbing sound at low frequency.

Management number identification method for nuclear fuel assembly

International Nuclear Information System (INIS)

Furuya, Nobuo; Mori, Kazuma.

1995-01-01

In the present invention, a management number indicated to appropriate portions of a fuel assembly can be read with no error for the management of nuclear fuel materials in the nuclear fuel assembly (counting management) and physical protection: PP. Namely, bar codes as a management number are printed by electrolytic polishing to one or more portions of a side surface of an upper nozzle of the assembly, an upper surface of a clamp and a side surface of a lower nozzle. The bar codes are read by a reader at one or more portions in a transporting path for transporting the fuel assembly and at a fuel detection device disposed in a fuel storage pool. The read signals are inputted to a computer. With such procedures, the nuclear fuel assembly can be identified with no error by reading the bar codes and without applying no danger to a human body. Since the reader is disposed in the course of the transportation and test for the assembly, and the read signals are inputted to the computer, the management for the counting number and PP is facilitated. (I.S.)

A generalized macro-assembler

International Nuclear Information System (INIS)

Kaul, Mohan Lai

1970-01-01

The objective of this research is to study existing macro assemblers, and to create a generalized macro assembler, MAG-I, which is a system independent of a source language, and provides the following possibilities: development of any existing language, translation from a language to another, and creation of a new language. The user can choose his own notations to define macros. The system is implemented on an IBM 360/91 computer. Programs are written in symbolic language and the input/output software is written in Fortran [fr

Scanning electron microscope/energy dispersive x ray analysis of impact residues in LDEF tray clamps

Science.gov (United States)

Bernhard, Ronald P.; Durin, Christian; Zolensky, Michael E.

1993-01-01

Detailed optical scanning of tray clamps is being conducted in the Facility for the Optical Inspection of Large Surfaces at JSC to locate and document impacts as small as 40 microns in diameter. Residues from selected impacts are then being characterized by Scanning Electron Microscopy/Energy Dispersive X-ray Analysis at CNES. Results from this analysis will be the initial step to classifying projectile residues into specific sources.

An applicable method for efficiency estimation of operating tray distillation columns and its comparison with the methods utilized in HYSYS and Aspen Plus

Science.gov (United States)

Sadeghifar, Hamidreza

2015-10-01

Developing general methods that rely on column data for the efficiency estimation of operating (existing) distillation columns has been overlooked in the literature. Most of the available methods are based on empirical mass transfer and hydraulic relations correlated to laboratory data. Therefore, these methods may not be sufficiently accurate when applied to industrial columns. In this paper, an applicable and accurate method was developed for the efficiency estimation of distillation columns filled with trays. This method can calculate efficiency as well as mass and heat transfer coefficients without using any empirical mass transfer or hydraulic correlations and without the need to estimate operational or hydraulic parameters of the column. E.g., the method does not need to estimate tray interfacial area, which can be its most important advantage over all the available methods. The method can be used for the efficiency prediction of any trays in distillation columns. For the efficiency calculation, the method employs the column data and uses the true rates of the mass and heat transfers occurring inside the operating column. It is highly emphasized that estimating efficiency of an operating column has to be distinguished from that of a column being designed.

Exposure to antimony from polyethylene terephthalate (PET) trays used in ready-to-eat meals.

Science.gov (United States)

Haldimann, M; Blanc, A; Dudler, V

2007-08-01

Antimony residues, a result of the use of a polycondensation catalyst in the production of polyethylene terephthalate (PET) oven-proof trays, were analysed in ready-to-eat meals. The toxicity of antimony has raised concerns about consumer safety; therefore, the migration of small fractions of these residues into ready meals and foods as a result of cooking directly in the PET trays was studied. A straightforward approach of measuring real samples was selected to obtain accurate exposure data. Background antimony concentration was determined separately from a series of lunch meals, which ranged from not detectable to 3.4 microg kg(-1). Microwave and conventional oven-cooking caused a distinct increase in the concentration of antimony in food and ready meals of 0-17 and 8-38 microg kg(-1), respectively, depending, to a certain extent, on the industrial preparations. The migrated quantities of antimony corresponded to 3-13 microg. For comparison, PET roasting bags and ready-made dough products in PET baking dishes were also evaluated. About half of the products prepared at a temperature of 180 degrees C exceeded the specific migration limit set for food contact material by the European Commission. However, the migrated amounts of antimony relative to the accepted tolerable daily intake (TDI) show that exposure from this type of food is currently not of toxicological concern.

Clinical study of the safety and effectiveness of a novel over-the-counter bleaching tray system

Science.gov (United States)

Ghalili, K Michael; Khawaled, Kamal; Rozen, Doran; Afsahi, Veda

2014-01-01

We investigated color change, gingival irritation, and tooth sensitivity in patients undergoing at-home vital tooth bleaching with a novel over-the-counter bleaching tray system. Tooth color shade in anterior teeth, supragingival plaque and gingivitis in Ramfjord teeth, as well as visual assessment of teeth gingival tissues and mucosa were evaluated in-office prior to treatment, after two consecutive applications of the 9% hydrogen peroxide bleaching product, after eight applications (10 minutes/day for 3 days at home), and after ten applications (50 minutes exposure over 5 days). Color stability was evaluated at 3 months after completing the treatment regimen. Over-the-counter bleaching products can be used by the patient at home without dentist supervision, but are frequently associated with gingival irritation and tooth sensitivity despite low concentrations of peroxide agents. Our investigations showed that the treatment is tolerable and safe with a low incidence of adverse effects. Any adverse effects associated with use of the whitening gel and tray are temporary, easily controlled, and often disappear within minutes of treatment. Statistical analysis revealed significant improvement in teeth whitening following treatment (mean color change of seven shades) and at three months after treatment. PMID:24591847

Startup and operation at the Browns Ferry Nuclear Plant (includes March 22, 1975, cabel tray fire)

International Nuclear Information System (INIS)

Metke, R.G.

1977-01-01

This paper addresses itself to significant events experienced during startup and operation of the three unit Browns Ferry Nuclear Plant located near Athens, Alabama. It consists of two major parts: (1) Resolution of significant equipment problems, and (2) Description of the March 22, 1975, cable tray fire. Identification of principal problems and their solutions should help prevent similar obstacles and related costly delays at other nuclear stations

Fiscal 1998 achievement report. Venture business raising type regional consortium - Small business creation base type (Development of nursery tray pickup robot and transport system for rice or vegetable growing); 1998 nendo suito oyobi yasai nado no hako ikubyo no robot naetori hanso system no kaihatsu (dai 2 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to develop energy conservation technologies through robotizing the processes of uprooting and conveying rice or vegetable seedlings. In fiscal 1998, the task covered root cutting and seedling uprooting, and a method was designed in which seedlings were uprooted through the intermediary of strings placed to run under the nursery trays. An effort was started to build an experimental root-cutting/seedling-pickup device. Systems for housing and conveying seedling trays were built simultaneously with a seedling tray loading system. In fiscal 1999, the root-cutting/seedling-pickup device was tested repeatedly for its seedling-pickup performance, and was modified. The nursery tray housing and conveying system accommodates a total of 84 trays in a 2-line 7-stage arrangement with 6 trays mounted on each stage. The conveyance speed was set at 0.4m/s-0.5m/s, and the trays travelled with stability in the system house. As for tray loading, an experimental device was built in which the mechanism for replacing empty trays with full trays had been changed from the turn table mechanism to a lateral movement type. Tests were conducted and it was demonstrated that the experimental device operated smoothly. A commercialization survey was conducted, and a conclusion was reached that a quarter of the target farmers in Hokkaido would positively accept the new technologies and adopt this system. (NEDO)

Tabulation of Fundamental Assembly Heat and Radiation Source Files

International Nuclear Information System (INIS)

T. deBues; J.C. Ryman

2006-01-01

The purpose of this calculation is to tabulate a set of computer files for use as input to the WPLOAD thermal loading software. These files contain details regarding heat and radiation from pressurized water reactor (PWR) assemblies and boiling water reactor (BWR) assemblies. The scope of this calculation is limited to rearranging and reducing the existing file information into a more streamlined set of tables for use as input to WPLOAD. The electronic source term files used as input to this calculation were generated from the output files of the SAS2H/ORIGIN-S sequence of the SCALE Version 4.3 modular code system, as documented in References 2.1.1 and 2.1.2, and are included in Attachment II

ARM assembly language with hardware experiments

CERN Document Server

Elahi, Ata

2015-01-01

This book provides a hands-on approach to learning ARM assembly language with the use of a TI microcontroller. The book starts with an introduction to computer architecture and then discusses number systems and digital logic. The text covers ARM Assembly Language, ARM Cortex Architecture and its components, and Hardware Experiments using TILM3S1968. Written for those interested in learning embedded programming using an ARM Microcontroller. ·         Introduces number systems and signal transmission methods   ·         Reviews logic gates, registers, multiplexers, decoders and memory   ·         Provides an overview and examples of ARM instruction set   ·         Uses using Keil development tools for writing and debugging ARM assembly language Programs   ·         Hardware experiments using a Mbed NXP LPC1768 microcontroller; including General Purpose Input/Output (GPIO) configuration, real time clock configuration, binary input to 7-segment display, creating ...

Online unsupervised formation of cell assemblies for the encoding of multiple cognitive maps.

Science.gov (United States)

Salihoglu, Utku; Bersini, Hugues; Yamaguchi, Yoko; Molter, Colin

2009-01-01

Since their introduction sixty years ago, cell assemblies have proved to be a powerful paradigm for brain information processing. After their introduction in artificial intelligence, cell assemblies became commonly used in computational neuroscience as a neural substrate for content addressable memories. However, the mechanisms underlying their formation are poorly understood and, so far, there is no biologically plausible algorithms which can explain how external stimuli can be online stored in cell assemblies. We addressed this question in a previous paper [Salihoglu, U., Bersini, H., Yamaguchi, Y., Molter, C., (2009). A model for the cognitive map formation: Application of the retroaxonal theory. In Proc. IEEE international joint conference on neural networks], were, based on biologically plausible mechanisms, a novel unsupervised algorithm for online cell assemblies' creation was developed. The procedure involved simultaneously, a fast Hebbian/anti-Hebbian learning of the network's recurrent connections for the creation of new cell assemblies, and a slower feedback signal which stabilized the cell assemblies by learning the feedforward input connections. Here, we first quantify the role played by the retroaxonal feedback mechanism. Then, we show how multiple cognitive maps, composed by a set of orthogonal input stimuli, can be encoded in the network. As a result, when facing a previously learned input, the system is able to retrieve the cognitive map it belongs to. As a consequence, ambiguous inputs which could belong to multiple cognitive maps can be disambiguated by the knowledge of the context, i.e. the cognitive map.

Burnup Measurement of Spent Fuel Assembly by CZT-based Gamma-ray Spectroscopy for Input Nuclear Material Accountancy of Pyroprocessing

International Nuclear Information System (INIS)

Seo, Hee; Oh, Jong-Myeong; Shin, Hee-Sung; Kim, Ho-Dong; Lee, Seung-Kyu; Park, Se-Hwan

2013-06-01

Input nuclear material accountancy is crucial for a pyroprocessing facility safeguards. Until a direct Pu measurement technique is established, an indirect method based on code calculations with burnup measurement and neutron counting for 244 Cm could be a practical option. Burnup can be determined by destructive analysis (DA) for final dispositive accuracy or by nondestructive assay (NDA) for near-real time accountancy. In the present study, an underwater burnup measurement system based on gamma-ray spectroscopy with the CZT detector was developed and tested on a spent fuel assembly. Burnup was determined according to the 134 Cs/ 137 Cs activity ratio with efficiency correction by Geant4 Monte Carlo simulations. The activity ratio as a function of burnup was obtained by ORIGEN calculations. The measured burnup error was 8.6%, which was within the measurement uncertainty. It is expected that the underwater burnup measurement system could fulfill an important role as a means of near-real time accountancy at a future pyroprocessing facility. (authors)

A simplified Track Assembler I/O for the Muon Trigger Track Finder

CERN Document Server

Dallavalle, Gaetano-Marco; Genchev, Vladimir; Grandi, Claudio; Neumeister, Norbert; Porth, Paul; Rohringer, Herbert

1998-01-01

One of the architectural concerns in the present design of the Muon Trigger Track Finder ( MTTF) is the large number of inputs to the Track Assembler ( TA). In the TA block, input track segment pairs from many Extrapolation Units ( EU) are associated into tracks. The relative contribution of these inputs to the assembled tracks is studied with simulated track patterns for low and high pt muons over the entire eta, phi acceptance of the CMS barrel. A pruning of the EUs is proposed which does not alter the performance of the Track Finder and minimizes the interconnections between azimuthal wedges.

Fully predictive simulation of real-scale cable tray fire based on small-scale laboratory experiments

Energy Technology Data Exchange (ETDEWEB)

Beji, Tarek; Merci, Bart [Ghent Univ. (Belgium). Dept. of Flow, Heat and Combustion Mechanics; Bonte, Frederick [Bel V, Brussels (Belgium)

2015-12-15

This paper presents a computational fluid dynamics (CFD)-based modelling strategy for real-scale cable tray fires. The challenge was to perform fully predictive simulations (that could be called 'blind' simulations) using solely information from laboratory-scale experiments, in addition to the geometrical arrangement of the cables. The results of the latter experiments were used (1) to construct the fuel molecule and the chemical reaction for combustion, and (2) to estimate the overall pyrolysis and burning behaviour. More particularly, the strategy regarding the second point consists of adopting a surface-based pyrolysis model. Since the burning behaviour of each cable could not be tracked individually (due to computational constraints), 'groups' of cables were modelled with an overall cable surface area equal to the actual value. The results obtained for one large-scale test (a stack of five horizontal trays) are quite encouraging, especially for the peak Heat Release Rate (HRR) that was predicted with a relative deviation of 3 %. The time to reach the peak is however overestimated by 4.7 min (i.e. 94 %). Also, the fire duration is overestimated by 5 min (i.e. 24 %). These discrepancies are mainly attributed to differences in the HRRPUA (heat release rate per unit area) profiles between the small-scale and large-scale. The latter was calculated by estimating the burning area of cables using video fire analysis (VFA).

Energy and exergy analyses of native cassava starch drying in a tray dryer

International Nuclear Information System (INIS)

Aviara, Ndubisi A.; Onuoha, Lovelyn N.; Falola, Oluwakemi E.; Igbeka, Joseph C.

2014-01-01

Energy and exergy analyses of native cassava starch drying in a tray dryer were carried out to assess the performance of the system in terms of energy utilization, energy utilization ratio, energy efficiency, exergy inflow and outflow, exergy loss and exegetic efficiency. The results indicated that for the starch with ash content of 0.76%, 0.85% crude protein, 0.16% crude fat, negligible amount of fiber, average granule size of 14.1 μm, pH of 5.88, amylose content of 23.45% and degree of crystallinity of 22.34%, energy utilization and energy utilization ratio increased from 1.93 to 5.51 J/s and 0.65 to 0.6 as the drying temperature increased from 40 to 60 °C. Energy efficiency increased from 16.036 to 30.645%, while exergy inflow, outflow and losses increased from 0.399 to 2.686, 0.055 to 0.555 and 0.344 to 2.131 J/s respectively in the above temperature range. Exergetic efficiency increased with increase in both drying air temperature and energy utilization and was lower than energy efficiency. Exergetic improvement potential also increased with increase in drying air temperature. Model equations that could be used to express the energy and exergy parameters as a function of drying temperature were established. - Highlights: • Energy and exergy analyses of cassava starch drying in a tray dryer were carried out. • Energy utilization increased with drying temperature. • Energy efficiency was higher than exergy efficiency. • Energy and exergy efficiencies increased with increase in temperature. • Improvement potential increased with increase in temperature

Fixture for aligning motor assembly

Science.gov (United States)

Shervington, Roger M.; Vaghani, Vallabh V.; Vanek, Laurence D.; Christensen, Scott A.

2009-12-08

An alignment fixture includes a rotor fixture, a stator fixture and a sensor system which measures a rotational displacement therebetween. The fixture precisely measures rotation of a generator stator assembly away from a NULL position referenced by a unique reference spline on the rotor shaft. By providing an adjustable location of the stator assembly within the housing, the magnetic axes within each generator shall be aligned to a predetermined and controlled tolerance between the generator interface mounting pin and the reference spline on the rotor shaft. Once magnetically aligned, each generator is essentially a line replaceable unit which may be readily mounted to any input of a multi-generator gearbox assembly with the assurance that the magnetic alignment will be within a predetermined tolerance.

Recommended connections between the main ionizing radiation sensors and their electronic sub-assemblies

International Nuclear Information System (INIS)

Lefevre, Roger; Roquefort, Henri

1970-02-01

The authors report the study of several typical and simple connections which are present between an ionizing radiation detector and the electronic sub-assembly, and can be adequate in most of the cases. They also study recommended outputs of the different types of detectors and their possible connections with electronic functional elements. Thus, they address connections for general use, detector outputs, inputs and outputs of amplifiers and of sub-assemblies, amplifier inputs, commonly used connectors

Effect of tray-based and trayless tooth whitening systems on microhardness of enamel surface and subsurface.

Science.gov (United States)

Teixeira, Erica C N; Ritter, André V; Thompson, Jeffrey Y; Leonard, Ralph H; Swift, Edward J

2004-12-01

To evaluate the effect of tray-based and trayless tooth whitening systems on surface and subsurface microhardness of human enamel. Enamel slabs were obtained from recently extracted human third molars. Specimens were randomly assigned to six groups according to tooth whitening treatment (n = 10): 6.0% hydrogen peroxide (HP) (Crest Whitestrips), 6.5% HP (Crest Professional Whitestrips), 7.5% HP (Day White Excel 3), 9.5% HP (Day White Excel 3), 10% carbamide peroxide (Opalescence), and a control group (untreated). Specimens were treated for 14 days following manufacturers' recommended protocols, and were immersed in artificial saliva between treatments. Enamel surface Knoop microhardness (KHN) was measured immediately before treatment, and at days 1, 7, and 14 of treatment. After treatment, subsurface microhardness was measured at depths of 50-500 microm. Data were analyzed for statistical significance using analysis of variance. Differences in microhardness for treated vs. untreated enamel surface were not statistically significant at any time interval. For 6.5% and 9.5% HP, there was a decrease in surface microhardness values during treatment, but at the end of treatment the microhardness values were not statistically different from the baseline values. For the enamel subsurface values, no differences were observed between treated vs. untreated specimens at each depth. Trayless and tray-based tooth whitening treatments do not significantly affect surface or subsurface enamel microhardness.

Tablet—next generation sequence assembly visualization

Science.gov (United States)

Milne, Iain; Bayer, Micha; Cardle, Linda; Shaw, Paul; Stephen, Gordon; Wright, Frank; Marshall, David

2010-01-01

Summary: Tablet is a lightweight, high-performance graphical viewer for next-generation sequence assemblies and alignments. Supporting a range of input assembly formats, Tablet provides high-quality visualizations showing data in packed or stacked views, allowing instant access and navigation to any region of interest, and whole contig overviews and data summaries. Tablet is both multi-core aware and memory efficient, allowing it to handle assemblies containing millions of reads, even on a 32-bit desktop machine. Availability: Tablet is freely available for Microsoft Windows, Apple Mac OS X, Linux and Solaris. Fully bundled installers can be downloaded from http://bioinf.scri.ac.uk/tablet in 32- and 64-bit versions. Contact: tablet@scri.ac.uk PMID:19965881

Effects of Impression Material, Impression Tray Type, and Type of Partial Edentulism on the Fit of Cobalt-Chromium Partial Denture Frameworks on Initial Clinical Insertion: A Retrospective Clinical Evaluation.

Science.gov (United States)

Baig, Mirza Rustum; Akbar, Jaber Hussain; Qudeimat, Muawia; Omar, Ridwaan

2018-02-15

To evaluate the effects of impression material, impression tray type, and type of partial edentulism (ie, Kennedy class) on the accuracy of fit of cobalt-chromium (Co-Cr) partial removable dental prostheses (PRDP) in terms of the number of fabricated frameworks required until the attainment of adequate fit. Electronic case documentations of 120 partially edentulous patients provided with Co-Cr PRDP treatment for one or both arches were examined. Statistical analyses of data were performed using analysis of variance and Tukey honest significant difference test to compare the relationships between the different factors and the number of frameworks that needed to be fabricated for each patient (α = .05). Statistical analysis of data derived from 143 records (69 maxillary and 74 mandibular) revealed no significant correlation between impression material, tray type, or Kennedy class and the number of construction attempts for the pooled or individual arch data (P ≥ .05). In PRDP treatment, alginate can be chosen as a first-choice material, and metal stock trays can be a preferred option for making final impressions to fabricate Co-Cr frameworks.

Input Shaping to Reduce Solar Array Structural Vibrations

Science.gov (United States)

Doherty, Michael J.; Tolson, Robert J.

1998-01-01

Structural vibrations induced by actuators can be minimized using input shaping. Input shaping is a feedforward method in which actuator commands are convolved with shaping functions to yield a shaped set of commands. These commands are designed to perform the maneuver while minimizing the residual structural vibration. In this report, input shaping is extended to stepper motor actuators. As a demonstration, an input-shaping technique based on pole-zero cancellation was used to modify the Solar Array Drive Assembly (SADA) actuator commands for the Lewis satellite. A series of impulses were calculated as the ideal SADA output for vibration control. These impulses were then discretized for use by the SADA stepper motor actuator and simulated actuator outputs were used to calculate the structural response. The effectiveness of input shaping is limited by the accuracy of the knowledge of the modal frequencies. Assuming perfect knowledge resulted in significant vibration reduction. Errors of 10% in the modal frequencies caused notably higher levels of vibration. Controller robustness was improved by incorporating additional zeros in the shaping function. The additional zeros did not require increased performance from the actuator. Despite the identification errors, the resulting feedforward controller reduced residual vibrations to the level of the exactly modeled input shaper and well below the baseline cases. These results could be easily applied to many other vibration-sensitive applications involving stepper motor actuators.

Methodologies to determine the Pu content of spent fuel assemblies for input nuclear material accountancy of pyroporcessing

International Nuclear Information System (INIS)

Lee, Taehoon; Shin, Heesung; Kim, Youngsoo; Kim, Hodong; Kwon, Taeje

2011-01-01

This study shows two different non-destructive approaches to determine the Pu mass of spent fuel assemblies, and the analysis results on the errors in their Pu mass. For both methods, the Cm mass of the assembly is obtained based on the neutron measurement results. The Cm ratio of the assembly is determined from the Cm mass and the Pu mass obtained by using either of the two methods. In a comparison of two methods, the second method is simpler than the first and may not need a homogeneously-mixed sample of the spent fuel assembly. On the other hand, the second approach shows larger error in the estimated Pu mass than the first one for many different spent fuel cases of various burnup, initial enrichment, and cooling times. A member state support program for the development of the IAEA safeguards approach for an engineering-scale pyroprocessing facility, which is designated as the Reference Engineering-scale Pyroprocessing Facility(REPF), has been carried out by Korea Atomic Energy Research Institute since 2008. The nuclear material accountancy of the REPF is based on the 'Cm balance' technique. The Pu content of processing materials of pyroprocessing can be determined by measuring the Cm mass of the materials and multiplying it by the Cm ratio. The spent fuel assembly is de-cladded, and the irradiated UO 2 material of the assembly is homogeneously mixed in the homogenization process in order to obtain a representative sample of the spent fuel assembly for determining the mass of Pu, U and Cm elements, as well as the Cm ratio of the campaign. The shipper-receiver difference between the nuclear power plant and HPC of REPF is determined at this point. We found that the error for the Pu mass and Cm ratio determined from the homogenized uranium oxide powder is the most critical for the determination of the material unaccounted for throughout the whole processes. This paper presents two approaches to determine the Pu mass of spent fuel assemblies using non

SAGE: String-overlap Assembly of GEnomes.

Science.gov (United States)

Ilie, Lucian; Haider, Bahlul; Molnar, Michael; Solis-Oba, Roberto

2014-09-15

De novo genome assembly of next-generation sequencing data is one of the most important current problems in bioinformatics, essential in many biological applications. In spite of significant amount of work in this area, better solutions are still very much needed. We present a new program, SAGE, for de novo genome assembly. As opposed to most assemblers, which are de Bruijn graph based, SAGE uses the string-overlap graph. SAGE builds upon great existing work on string-overlap graph and maximum likelihood assembly, bringing an important number of new ideas, such as the efficient computation of the transitive reduction of the string overlap graph, the use of (generalized) edge multiplicity statistics for more accurate estimation of read copy counts, and the improved use of mate pairs and min-cost flow for supporting edge merging. The assemblies produced by SAGE for several short and medium-size genomes compared favourably with those of existing leading assemblers. SAGE benefits from innovations in almost every aspect of the assembly process: error correction of input reads, string-overlap graph construction, read copy counts estimation, overlap graph analysis and reduction, contig extraction, and scaffolding. We hope that these new ideas will help advance the current state-of-the-art in an essential area of research in genomics.

Produção de bulbinhos de cebola em bandejas de isopor Production of onion bulb sets in styrofoam trays

Directory of Open Access Journals (Sweden)

Antonio Ismael Inácio Cardoso

1999-10-01

Full Text Available Com o objetivo de estudar a viabilidade de produção de bulbinhos de cebola sob ambiente protegido em diferentes tipos de bandejas de poliestireno expandido foram instalados dois experimentos. No primeiro, trabalhando com a cultivar Serrana, foram avaliadas três tipos de bandejas com diferentes números de plantas por célula: uma planta/célula na bandeja de 288 células, três a cinco plantas/célula na de 128 e cinco a nove plantas/célula na de 72 células. No outro experimento, testaram-se nove cultivares, semeadas somente em bandejas de 128 células com três plantas por célula. Utilizou-se o delineamento em blocos ao acaso com quatro repetições no primeiro ensaio e cinco no segundo, sendo cada parcela constituída por uma bandeja. Observou-se que quanto maior a densidade de plantio menor o tamanho do bulbinho (diâmetro e peso. O manejo adequado de adubações em cobertura pode viabilizar, tecnicamente, a produção de cinco bulbinhos com 1,3 cm de diâmetro (2 g por célula, na bandeja de 128 células. Quanto ao ensaio de cultivares, ‘Crioula’ da Agroflora, ‘Crioula’ da Granja Lotário e ‘Houston’ apresentaram 83%, 67% e 81% de plantas bulbificadas, enquanto que nas demais (‘Aurora’, ‘Baia Periforme’, ‘Brownsville’, ‘Petroline’, ‘Pira Ouro’, ‘Pirana’ e ‘Serrana’ obteve-se 100% de bulbificação. As principais vantagens na produção de bulbinhos em bandeja foram: uniformidade, ausência de plantas daninhas e de patógenos. É um sistema que pode ser útil aos viveiristas que tem entressafra de mudas nos meses de agosto a novembro, período de produção dos bulbinhos. Poderá, também, ser uma alternativa na produção de bulbinhos para conserva, no controle de qualidade de lotes de sementes e em programas de melhoramento de cebola.One objective was to study the production of onion Allium cepa L.. bulb sets in a protected environment in a seedling system with trays with different number of

DNAzyme-Based Logic Gate-Mediated DNA Self-Assembly.

Science.gov (United States)

Zhang, Cheng; Yang, Jing; Jiang, Shuoxing; Liu, Yan; Yan, Hao

2016-01-13

Controlling DNA self-assembly processes using rationally designed logic gates is a major goal of DNA-based nanotechnology and programming. Such controls could facilitate the hierarchical engineering of complex nanopatterns responding to various molecular triggers or inputs. Here, we demonstrate the use of a series of DNAzyme-based logic gates to control DNA tile self-assembly onto a prescribed DNA origami frame. Logic systems such as "YES," "OR," "AND," and "logic switch" are implemented based on DNAzyme-mediated tile recognition with the DNA origami frame. DNAzyme is designed to play two roles: (1) as an intermediate messenger to motivate downstream reactions and (2) as a final trigger to report fluorescent signals, enabling information relay between the DNA origami-framed tile assembly and fluorescent signaling. The results of this study demonstrate the plausibility of DNAzyme-mediated hierarchical self-assembly and provide new tools for generating dynamic and responsive self-assembly systems.

Viabilidade do sistema de produção de mudas em bandejas em três cultivares de cebola Viability of onion seedling production on polyestyrene trays in three cultivars

Directory of Open Access Journals (Sweden)

Marie Yamamoto Reghin

2007-08-01

cultivo da cebola em um mercado cada vez mais competitivo.The present trial was realized in Ponta Grossa (PR and aimed to evaluate the viability of onion seedling production in polyestyrene trays, compared to conventional system on seedbed, using three cultivars The experimental design used was a randomized block with three replications. The treatments were arranged in a factorial scheme 3x3, being three seedlings type (from trays with 200 and 288 cells and from seedbed, and three cultivars (Mercedes, Bola Precoce and Crioula. Seedlings production on trays were realized under protected cultivation and seedlings from seedbeds produced in the field. Seeds were sowed in May,15th. At 57 days the seedlings were evaluated and then transplanted in plots with four rows and plants arranged in 0,40x0,08m, with 312.500 plants.ha-1. The harvest was realized according to the plant maturation stage. Bulbs were dried and then yield were evaluated. The production cost and seedlings viability were calculated. It was observed the seedlings from trays were superior when compared to seedlings from seedbed, mainly those from 200 cells.This higher seedling quality reflected on later performance obtaining the highest yield from trays of 200 cells. It was intermediary with 288 trays and lower from seedbed seedling. It was observed low seedling useful from seedbed during the selection process (50%. In the case of hybrid the cost of seedling production in seedbed was high, almost comparable to seedling production of open pollinated cultivars on trays of 288 cells. The best cultivars were Crioula and Mercedes. Seedlings production on trays mainly on 200 cells showed viability and represents an important alternative to increase onion yield in a competitive market.

Physical principles for DNA tile self-assembly.

Science.gov (United States)

Evans, Constantine G; Winfree, Erik

2017-06-19

DNA tiles provide a promising technique for assembling structures with nanoscale resolution through self-assembly by basic interactions rather than top-down assembly of individual structures. Tile systems can be programmed to grow based on logical rules, allowing for a small number of tile types to assemble large, complex assemblies that can retain nanoscale resolution. Such algorithmic systems can even assemble different structures using the same tiles, based on inputs that seed the growth. While programming and theoretical analysis of tile self-assembly often makes use of abstract logical models of growth, experimentally implemented systems are governed by nanoscale physical processes that can lead to very different behavior, more accurately modeled by taking into account the thermodynamics and kinetics of tile attachment and detachment in solution. This review discusses the relationships between more abstract and more physically realistic tile assembly models. A central concern is how consideration of model differences enables the design of tile systems that robustly exhibit the desired abstract behavior in realistic physical models and in experimental implementations. Conversely, we identify situations where self-assembly in abstract models can not be well-approximated by physically realistic models, putting constraints on physical relevance of the abstract models. To facilitate the discussion, we introduce a unified model of tile self-assembly that clarifies the relationships between several well-studied models in the literature. Throughout, we highlight open questions regarding the physical principles for DNA tile self-assembly.

Integral Fast Reactor fuel pin processor

International Nuclear Information System (INIS)

Levinskas, D.

1993-01-01

This report discusses the pin processor which receives metal alloy pins cast from recycled Integral Fast Reactor (IFR) fuel and prepares them for assembly into new IFR fuel elements. Either full length as-cast or precut pins are fed to the machine from a magazine, cut if necessary, and measured for length, weight, diameter and deviation from straightness. Accepted pins are loaded into cladding jackets located in a magazine, while rejects and cutting scraps are separated into trays. The magazines, trays, and the individual modules that perform the different machine functions are assembled and removed using remote manipulators and master-slaves

Interim Status Closure Plan Open Burning Treatment Unit Technical Area 16-399 Burn Tray

Energy Technology Data Exchange (ETDEWEB)

Vigil-Holterman, Luciana R. [Los Alamos National Laboratory

2012-05-07

This closure plan describes the activities necessary to close one of the interim status hazardous waste open burning treatment units at Technical Area (TA) 16 at the Los Alamos National Laboratory (LANL or the Facility), hereinafter referred to as the 'TA-16-399 Burn Tray' or 'the unit'. The information provided in this closure plan addresses the closure requirements specified in the Code of Federal Regulations (CFR), Title 40, Part 265, Subparts G and P for the thermal treatment units operated at the Facility under the Resource Conservation and Recovery Act (RCRA) and the New Mexico Hazardous Waste Act. Closure of the open burning treatment unit will be completed in accordance with Section 4.1 of this closure plan.

Sanitation Can Be A Foundation Disease Management Tool: Potential Of Spreading Binucleate Rhizoctonia from Nursery Propagation Floors To Trays Containing Azalea Stem Cuttings

Science.gov (United States)

Binucelate Rhizoctonia spp. (BNR), the cause of web blight, are present all year on container-grown azaleas in the southern U.S. BNR can be eliminated during vegetative propagation by submerging stem cuttings in 50°C water for 21 minutes. The objective was to evaluate risk of rooting trays being con...

Targeted assembly of short sequence reads.

Directory of Open Access Journals (Sweden)

René L Warren

Full Text Available As next-generation sequence (NGS production continues to increase, analysis is becoming a significant bottleneck. However, in situations where information is required only for specific sequence variants, it is not necessary to assemble or align whole genome data sets in their entirety. Rather, NGS data sets can be mined for the presence of sequence variants of interest by localized assembly, which is a faster, easier, and more accurate approach. We present TASR, a streamlined assembler that interrogates very large NGS data sets for the presence of specific variants by only considering reads within the sequence space of input target sequences provided by the user. The NGS data set is searched for reads with an exact match to all possible short words within the target sequence, and these reads are then assembled stringently to generate a consensus of the target and flanking sequence. Typically, variants of a particular locus are provided as different target sequences, and the presence of the variant in the data set being interrogated is revealed by a successful assembly outcome. However, TASR can also be used to find unknown sequences that flank a given target. We demonstrate that TASR has utility in finding or confirming genomic mutations, polymorphisms, fusions and integration events. Targeted assembly is a powerful method for interrogating large data sets for the presence of sequence variants of interest. TASR is a fast, flexible and easy to use tool for targeted assembly.

VAGUE: a graphical user interface for the Velvet assembler.

Science.gov (United States)

Powell, David R; Seemann, Torsten

2013-01-15

Velvet is a popular open-source de novo genome assembly software tool, which is run from the Unix command line. Most of the problems experienced by new users of Velvet revolve around constructing syntactically and semantically correct command lines, getting input files into acceptable formats and assessing the output. Here, we present Velvet Assembler Graphical User Environment (VAGUE), a multi-platform graphical front-end for Velvet. VAGUE aims to make sequence assembly accessible to a wider audience and to facilitate better usage amongst existing users of Velvet. VAGUE is implemented in JRuby and targets the Java Virtual Machine. It is available under an open-source GPLv2 licence from http://www.vicbioinformatics.com/. torsten.seemann@monash.edu.

Accuracy of implant transfer and surface detail reproduction with polyether and polyvinyl siloxane using closed-tray impression technique

Directory of Open Access Journals (Sweden)

Marzieh Alikhasi

2013-10-01

Full Text Available   Background and Aims: Making accurate impressions of prepared teeth when they are adjacent to dental implants is of great importance. In these situations, disregarding the selection of appropriate impression material and technique, not only can affect accuracy of transferring of the 3-dimentional spatial status of implant, but also can jeopardize the accurate recording of tooth. In the present study, the accuracy of two impression materials with taper impression copings for recording implant position and surface details was evaluated.   Materials and Methods: One metal reference model with 2 implants (Implantium and a preparation of three grooves on a tooth according to ADA no. 19 standard was fabricated. 10 medium- consistency polyEther (PE impressions using custom trays and 10 polyVinyl Siloxane (PVS putty wash impressions using prefabricated trays with conical impression coping were made. Impressions were poured with ADA type IV stone. A Coordinate Measuring Machine (CMM evaluated x, y and angular displacement of the implant analog heads and also accuracy of groove reproduction were measured using a Video Measuring Machine (VMM. These measurements were compared to the ones from reference model. Data were analyzed using one-way ANOVA and T-test.   Results: Putty wash PVS had less linear discrepancy compared with reference model (P > 0.001. There was no significant difference in the surface detail reproduction (P = 0.15.   Conclusion: Putty wash PVS had better results for linear displacement compared with medium consistency PE. There was no significant difference in surface detail reproduction between the two impression materials.

Graph mining for next generation sequencing: leveraging the assembly graph for biological insights.

Science.gov (United States)

Warnke-Sommer, Julia; Ali, Hesham

2016-05-06

The assembly of Next Generation Sequencing (NGS) reads remains a challenging task. This is especially true for the assembly of metagenomics data that originate from environmental samples potentially containing hundreds to thousands of unique species. The principle objective of current assembly tools is to assemble NGS reads into contiguous stretches of sequence called contigs while maximizing for both accuracy and contig length. The end goal of this process is to produce longer contigs with the major focus being on assembly only. Sequence read assembly is an aggregative process, during which read overlap relationship information is lost as reads are merged into longer sequences or contigs. The assembly graph is information rich and capable of capturing the genomic architecture of an input read data set. We have developed a novel hybrid graph in which nodes represent sequence regions at different levels of granularity. This model, utilized in the assembly and analysis pipeline Focus, presents a concise yet feature rich view of a given input data set, allowing for the extraction of biologically relevant graph structures for graph mining purposes. Focus was used to create hybrid graphs to model metagenomics data sets obtained from the gut microbiomes of five individuals with Crohn's disease and eight healthy individuals. Repetitive and mobile genetic elements are found to be associated with hybrid graph structure. Using graph mining techniques, a comparative study of the Crohn's disease and healthy data sets was conducted with focus on antibiotics resistance genes associated with transposase genes. Results demonstrated significant differences in the phylogenetic distribution of categories of antibiotics resistance genes in the healthy and diseased patients. Focus was also evaluated as a pure assembly tool and produced excellent results when compared against the Meta-velvet, Omega, and UD-IDBA assemblers. Mining the hybrid graph can reveal biological phenomena captured

Cellulase production through solid-state tray fermentation, and its use for bioethanol from sorghum stover.

Science.gov (United States)

Idris, Ayman Salih Omer; Pandey, Ashok; Rao, S S; Sukumaran, Rajeev K

2017-10-01

The production of cellulase by Trichoderma reesei RUT C-30 under solid-state fermentation (SSF) on wheat bran and cellulose was optimized employing a two stage statistical design of experiments. Optimization of process parameters resulted in a 3.2-fold increase in CMCase production to 959.53IU/gDS. The process was evaluated at pilot scale in tray fermenters and yielded 457IU/gDS using the lab conditions and indicating possibility for further improvement. The cellulase could effectively hydrolyze alkali pretreated sorghum stover and addition of Aspergillus niger β-glucosidase improved the hydrolytic efficiency 174%, indicating the potential to use this blend for effective saccharification of sorghum stover biomass. The enzymatic hydrolysate of sorghum stover was fermented to ethanol with ∼80% efficiency. Copyright © 2017 Elsevier Ltd. All rights reserved.

The System of Automatic Control of Complexity Work Evaluation in Assembly

Directory of Open Access Journals (Sweden)

Ivo HLAVATÝ

2011-06-01

Full Text Available The article is about a task of creating of an automated system for the evaluation of the complexity and the prediction of labour input of fitting and assembly operations, which used for manufacturing of machine-building item.

Hybrid reduced order modeling for assembly calculations

Energy Technology Data Exchange (ETDEWEB)

Bang, Y.; Abdel-Khalik, H. S. [North Carolina State University, Raleigh, NC (United States); Jessee, M. A.; Mertyurek, U. [Oak Ridge National Laboratory, Oak Ridge, TN (United States)

2013-07-01

While the accuracy of assembly calculations has considerably improved due to the increase in computer power enabling more refined description of the phase space and use of more sophisticated numerical algorithms, the computational cost continues to increase which limits the full utilization of their effectiveness for routine engineering analysis. Reduced order modeling is a mathematical vehicle that scales down the dimensionality of large-scale numerical problems to enable their repeated executions on small computing environment, often available to end users. This is done by capturing the most dominant underlying relationships between the model's inputs and outputs. Previous works demonstrated the use of the reduced order modeling for a single physics code, such as a radiation transport calculation. This manuscript extends those works to coupled code systems as currently employed in assembly calculations. Numerical tests are conducted using realistic SCALE assembly models with resonance self-shielding, neutron transport, and nuclides transmutation/depletion models representing the components of the coupled code system. (authors)

An evaluation of methodology for seismic qualification of equipment, cable trays, and ducts in ALWR plants by use of experience data

International Nuclear Information System (INIS)

Bandyopadhyay, K.K.; Kana, D.D.; Kennedy, R.P.; Schiff, A.J.

1997-07-01

Advanced Reactor Corporation (ARC) has developed a methodology for seismic qualification of equipment, cable trays and ducts in Advanced Light Water Reactor plants. A Panel (members of which acted as individuals) supported by the Office of Nuclear Regulatory Research of the Nuclear Regulatory Commission has evaluated this methodology. The review approach and observations are included in this report. In general, the Panel supports the ARC methodology with some exceptions and provides recommendations for further improvements. 26 refs., 10 figs., 1 tab

An evaluation of methodology for seismic qualification of equipment, cable trays, and ducts in ALWR plants by use of experience data

Energy Technology Data Exchange (ETDEWEB)

Bandyopadhyay, K.K.; Kana, D.D.; Kennedy, R.P.; Schiff, A.J.

1997-07-01

Advanced Reactor Corporation (ARC) has developed a methodology for seismic qualification of equipment, cable trays and ducts in Advanced Light Water Reactor plants. A Panel (members of which acted as individuals) supported by the Office of Nuclear Regulatory Research of the Nuclear Regulatory Commission has evaluated this methodology. The review approach and observations are included in this report. In general, the Panel supports the ARC methodology with some exceptions and provides recommendations for further improvements. 26 refs., 10 figs., 1 tab.

Study of sample-detector assemblies for application to in-situ measurement of radioactivity in liquid effluents

International Nuclear Information System (INIS)

Pendharkar, K.A.; Narayanan Kutty, K.; Krishnamony, S.

1991-01-01

This paper describes the experimental investigations carried out on four different types of sample-detector assemblies with a view to determining their detection limits and relative merits for application to in-situ measurement of radioactivity in liquid effluents. The four systems studied were: (1) gamma detection using 11 cm x 8 cm NaI (Tl) scintillation detector inserted in the cavity of a specially designed stainless steel chamber of capacity 15 liters, (2) gamma detection using a metal-walled G.M. counter in a similar manner, (3) beta detection using twin thin-walled G.M. counters immersed in liquid, and (4) end window G.M. counter positioned above the liquid surface in a shallow tray. The design features of an in-line monitor employing a 11 cm x 8 cm NaI (Tl) detector used for the routine monitoring of beta gamma activity concentrations in the low level effluents of the Tarapur Fuel Processing Plant are described. (author). 1 tab

Harnessing NGS and Big Data Optimally: Comparison of miRNA Prediction from Assembled versus Non-assembled Sequencing Data--The Case of the Grass Aegilops tauschii Complex Genome.

Science.gov (United States)

Budak, Hikmet; Kantar, Melda

2015-07-01

MicroRNAs (miRNAs) are small, endogenous, non-coding RNA molecules that regulate gene expression at the post-transcriptional level. As high-throughput next generation sequencing (NGS) and Big Data rapidly accumulate for various species, efforts for in silico identification of miRNAs intensify. Surprisingly, the effect of the input genomics sequence on the robustness of miRNA prediction was not evaluated in detail to date. In the present study, we performed a homology-based miRNA and isomiRNA prediction of the 5D chromosome of bread wheat progenitor, Aegilops tauschii, using two distinct sequence data sets as input: (1) raw sequence reads obtained from 454-GS FLX Titanium sequencing platform and (2) an assembly constructed from these reads. We also compared this method with a number of available plant sequence datasets. We report here the identification of 62 and 22 miRNAs from raw reads and the assembly, respectively, of which 16 were predicted with high confidence from both datasets. While raw reads promoted sensitivity with the high number of miRNAs predicted, 55% (12 out of 22) of the assembly-based predictions were supported by previous observations, bringing specificity forward compared to the read-based predictions, of which only 37% were supported. Importantly, raw reads could identify several repeat-related miRNAs that could not be detected with the assembly. However, raw reads could not capture 6 miRNAs, for which the stem-loops could only be covered by the relatively longer sequences from the assembly. In summary, the comparison of miRNA datasets obtained by these two strategies revealed that utilization of raw reads, as well as assemblies for in silico prediction, have distinct advantages and disadvantages. Consideration of these important nuances can benefit future miRNA identification efforts in the current age of NGS and Big Data driven life sciences innovation.

Dental image replacement on cone beam computed tomography with three-dimensional optical scanning of a dental cast, occlusal bite, or bite tray impression.

Science.gov (United States)

Kang, S-H; Lee, J-W; Lim, S-H; Kim, Y-H; Kim, M-K

2014-10-01

The goal of the present study was to compare the accuracy of dental image replacement on a cone beam computed tomography (CBCT) image using digital image data from three-dimensional (3D) optical scanning of a dental cast, occlusal bite, and bite tray impression. A Bracket Typodont dental model was used. CBCT of the dental model was performed and the data were converted to stereolithography (STL) format. Three experimental materials, a dental cast, occlusal bite, and bite tray impression, were optically scanned in 3D. STL files converted from the CBCT of the Typodont model and the 3D optical-scanned STL files of the study materials were image-registered. The error range of each methodology was measured and compared with a 3D optical scan of the Typodont. For the three materials, the smallest error observed was 0.099±0.114mm (mean error±standard deviation) for registering the 3D optical scan image of the dental cast onto the CBCT dental image. Although producing a dental cast can be laborious, the study results indicate that it is the preferred method. In addition, an occlusal bite is recommended when bite impression materials are used. Copyright © 2014 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Controlling Self-Assembly in Al(110) Homoepitaxy

Science.gov (United States)

Tiwary, Yogesh; Fichthorn, Kristen

2010-03-01

Homoepitaxial growth on Al(110) exhibits nanoscale self-assembly into huts with well-defined (100) and (111) facets [1]. Although some of the diffusion mechanisms underlying this kinetic self-assembly were identified and incorporated into a two-dimensional model [2], we used density-functional theory (DFT) to identify many other mechanisms that are needed to describe the three-dimensional assembly seen experimentally [3]. We developed a three-dimensional kinetic Monte Carlo (KMC) model of Al(110) homoepitaxy. The inputs to the model were obtained from DFT [3,4]. Our model is in agreement with experimentally observed trends for this system. We used KMC to predict self-assembly under various growth conditions. To achieve precise placement of Al nanohuts, we simulated thermal-field-directed assembly [5]. Our results indicate that this technique can be used to create uniform arrays of nanostructures. [1] F. Buatier de Mongeot, W. Zhu, A. Molle, R. Buzio, C. Boragno, U. Valbusa, E. Wang, and Z. Zhang, Phys. Rev. Lett. 91, 016102 (2003). [2] W. Zhu, F. Buatier de Mongeot, U. Valbusa, E. G. Wang, and Z. Y. Zhang, Phys. Rev. Lett. 92, 106102 (2004). [3] Y. Tiwary and K. A. Fichthorn, submitted to Phys. Rev. B. [4] Y. Tiwary and K. A. Fichthorn, Phys. Rev. B 78, 205418 (2008). [5] C. Zhang and R. Kalyanaraman, Appl. Phys. Lett. 83, 4827 (2003).

Reactor Dynamics Experiments with a Sub-Critical Assembly

International Nuclear Information System (INIS)

Miley, G.H.; Yang, Y.; Wu, L.; Momota, H.

2004-01-01

A resurgence in use of nuclear power is now underway worldwide. However due to the shutdown of many university research reactors , student laboratories must rely more heavily on use of sub-critical assemblies. Here a driven sub-critical is described that uses a cylindrical Inertial Electrostatic Confinement (IEC) device to provide a fusion neutron source. The small IEC neutron source would be inserted in a fuel element position, with its power input controlled externally at a control panel. This feature opens the way to use of the critical assembly for a number of transient experiments such as sub-critical pulsing and neutron wave propagation. That in turn adds important new insights and excitement for the student teaching laboratory

Energy Input Flux in the Global Quiet-Sun Corona

Energy Technology Data Exchange (ETDEWEB)

Mac Cormack, Cecilia; Vásquez, Alberto M.; López Fuentes, Marcelo; Nuevo, Federico A. [Instituto de Astronomía y Física del Espacio (IAFE), CONICET-UBA, CC 67—Suc 28, (C1428ZAA) Ciudad Autónoma de Buenos Aires (Argentina); Landi, Enrico; Frazin, Richard A. [Department of Climate and Space Sciences and Engineering (CLaSP), University of Michigan, 2455 Hayward Street, Ann Arbor, MI 48109-2143 (United States)

2017-07-01

We present first results of a novel technique that provides, for the first time, constraints on the energy input flux at the coronal base ( r ∼ 1.025 R {sub ⊙}) of the quiet Sun at a global scale. By combining differential emission measure tomography of EUV images, with global models of the coronal magnetic field, we estimate the energy input flux at the coronal base that is required to maintain thermodynamically stable structures. The technique is described in detail and first applied to data provided by the Extreme Ultraviolet Imager instrument, on board the Solar TErrestrial RElations Observatory mission, and the Atmospheric Imaging Assembly instrument, on board the Solar Dynamics Observatory mission, for two solar rotations with different levels of activity. Our analysis indicates that the typical energy input flux at the coronal base of magnetic loops in the quiet Sun is in the range ∼0.5–2.0 × 10{sup 5} (erg s{sup −1} cm{sup −2}), depending on the structure size and level of activity. A large fraction of this energy input, or even its totality, could be accounted for by Alfvén waves, as shown by recent independent observational estimates derived from determinations of the non-thermal broadening of spectral lines in the coronal base of quiet-Sun regions. This new tomography product will be useful for the validation of coronal heating models in magnetohydrodinamic simulations of the global corona.

Generation of SCALE 6 Input Data File for Cross Section Library of PWR Spent Fuel

International Nuclear Information System (INIS)

Jeong, Chang Joon; Cho, Dong Keun

2010-11-01

In order to obtain the cross section libraries of the Korean Pressurized water reactor (PWR) spent fuel (SF), SCALE 6 code input files have been generated. The PWR fuel data were obtained from the nuclear design report (NDR) of the current operating PWRs. The input file were prepared for 16 fuel types such as 4 types of Westinghouse 14x14, 3 types of OPR-1000 16x16, 4 types of Westinghouse 16x16, and 6 types of Westinghouse 17x17. For each fuel type, 5 kinds of fuel enrichments have been considered such as 1.5, 2.0 ,3.0, 4.0 and 5.0 wt%. In the SCALE 6 calculation, a ENDF-V 44 group was used. The 25 burnup step until 72000 MWD/T was used. A 1/4 symmetry model was used for 16x16 and 17x17 fuel assembly, and 1/2 symmetry model was used for 14x14 fuel assembly The generated cross section libraries will be used for the source-term analysis of the PWR SF

Hybrid reduced order modeling for assembly calculations

Energy Technology Data Exchange (ETDEWEB)

Bang, Youngsuk, E-mail: ysbang00@fnctech.com [FNC Technology, Co. Ltd., Yongin-si (Korea, Republic of); Abdel-Khalik, Hany S., E-mail: abdelkhalik@purdue.edu [Purdue University, West Lafayette, IN (United States); Jessee, Matthew A., E-mail: jesseema@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Mertyurek, Ugur, E-mail: mertyurek@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN (United States)

2015-12-15

Highlights: • Reducing computational cost in engineering calculations. • Reduced order modeling algorithm for multi-physics problem like assembly calculation. • Non-intrusive algorithm with random sampling. • Pattern recognition in the components with high sensitive and large variation. - Abstract: While the accuracy of assembly calculations has considerably improved due to the increase in computer power enabling more refined description of the phase space and use of more sophisticated numerical algorithms, the computational cost continues to increase which limits the full utilization of their effectiveness for routine engineering analysis. Reduced order modeling is a mathematical vehicle that scales down the dimensionality of large-scale numerical problems to enable their repeated executions on small computing environment, often available to end users. This is done by capturing the most dominant underlying relationships between the model's inputs and outputs. Previous works demonstrated the use of the reduced order modeling for a single physics code, such as a radiation transport calculation. This manuscript extends those works to coupled code systems as currently employed in assembly calculations. Numerical tests are conducted using realistic SCALE assembly models with resonance self-shielding, neutron transport, and nuclides transmutation/depletion models representing the components of the coupled code system.

Hybrid reduced order modeling for assembly calculations

International Nuclear Information System (INIS)

Bang, Youngsuk; Abdel-Khalik, Hany S.; Jessee, Matthew A.; Mertyurek, Ugur

2015-01-01

Highlights: • Reducing computational cost in engineering calculations. • Reduced order modeling algorithm for multi-physics problem like assembly calculation. • Non-intrusive algorithm with random sampling. • Pattern recognition in the components with high sensitive and large variation. - Abstract: While the accuracy of assembly calculations has considerably improved due to the increase in computer power enabling more refined description of the phase space and use of more sophisticated numerical algorithms, the computational cost continues to increase which limits the full utilization of their effectiveness for routine engineering analysis. Reduced order modeling is a mathematical vehicle that scales down the dimensionality of large-scale numerical problems to enable their repeated executions on small computing environment, often available to end users. This is done by capturing the most dominant underlying relationships between the model's inputs and outputs. Previous works demonstrated the use of the reduced order modeling for a single physics code, such as a radiation transport calculation. This manuscript extends those works to coupled code systems as currently employed in assembly calculations. Numerical tests are conducted using realistic SCALE assembly models with resonance self-shielding, neutron transport, and nuclides transmutation/depletion models representing the components of the coupled code system.

Produtividade da couve-flor em função da idade de transplantio das mudas e tamanhos de células na bandeja Cauliflower production depending on age of seedling and cell size of the trays

Directory of Open Access Journals (Sweden)

Maria Carolina Godoy

2005-07-01

Full Text Available O experimento foi realizado de novembro de 2000 a abril de 2001, na UNESP em São Manuel (SP. Estudou-se o efeito do tamanho da célula da bandeja de poliestireno expandido e a idade de transplantio das mudas sobre a produção de couve-flor, híbrido Shiromaru II. Usaram-se bandejas com 128 e 288 células, correspondentes a 34,6 e 9,7 cm³/célula, respectivamente, e mudas transplantadas aos 27, 34, 41 e 48 dias após a semeadura. Os tratamentos foram arranjados como fatorial 2 x 4, dispostos no delineamento de blocos casualizados, com cinco repetições. Foram avaliados, por ocasião do transplantio, o número de folhas, peso fresco, peso seco e área foliar das mudas. A parcela experimental no campo foi constituída por dez plantas. Nas colheitas, avaliaram-se a porcentagem de plantas com cabeça comercial e nestas, o número de folhas, peso fresco e diâmetro da cabeça. A produção total por parcela foi obtida com a soma do peso fresco de todas as cabeças consideradas comerciais. A produção de mudas em bandejas com 128 células proporcionou maior porcentagem de plantas comerciais (64% relativamente às bandejas com 288 células (45%, maior peso médio de cabeça (337 g na bandeja com 128 e 247 g na bandeja com 288 células e maior produção de plantas comerciais (36,9 t/ha em bandeja de 128 células e 19,9 t/ha em bandeja de 288 células. As mudas transplantadas com 32 dias apresentaram maior peso médio de cabeça (319 g. Concluiu-se ser recomendável produzir mudas de couve-flor em bandejas com 128 células.The experiment was carried out from November/2000 to April/2001, in São Manuel, São Paulo State, Brazil. The effect of cell size of two polyestyrene trays and age of seedling at transplanting date was observed, on the production of cauliflower, hybrid Shiromaru II. Trays with 128 and 288 cells, corresponding to 34.6 and 9.7 cm³/cell, respectively, were used with seedlings transplanted at 27; 34; 41 and 48 days after sowing date

Facility for protection of technological, especially power assemblies

International Nuclear Information System (INIS)

Cichon, S.; Hahn, J.; Malatek, K.; Randak, O.; Vitovec, P.; Zidek, M.

1987-01-01

The facility consists of sensors producing analog signals, used as input information for the evaluation of process conditions or equipment failures. The sensors are fitted to partial functional parts of technological assemblies, such as nuclear reactors. The individual sensors are connected via unification converters to the respective protection units. The facility is resistant to breakdowns of the analog sensors and other components including the computer; it features the possibility of in-service failure detection and the capability of immediate regeneration following a failure. This capability prevents, with high probability, the production of non-accident failures of the technological assembly. The block diagram is described of the facility and its operation in the event of an emergency. (J.B.). 1 fig

The effect of cutting conditions on power inputs when machining

Science.gov (United States)

Petrushin, S. I.; Gruby, S. V.; Nosirsoda, Sh C.

2016-08-01

Any technological process involving modification of material properties or product form necessitates consumption of a certain power amount. When developing new technologies one should take into account the benefits of their implementation vs. arising power inputs. It is revealed that procedures of edge cutting machining are the most energy-efficient amongst the present day forming procedures such as physical and technical methods including electrochemical, electroerosion, ultrasound, and laser processing, rapid prototyping technologies etc, such as physical and technical methods including electrochemical, electroerosion, ultrasound, and laser processing, rapid prototyping technologies etc. An expanded formula for calculation of power inputs is deduced, which takes into consideration the mode of cutting together with the tip radius, the form of the replaceable multifaceted insert and its wear. Having taken as an example cutting of graphite iron by the assembled cutting tools with replaceable multifaceted inserts the authors point at better power efficiency of high feeding cutting in comparison with high-speed cutting.

Opto-mechanical design of the MTG FCI spectral separation assembly

Science.gov (United States)

Riguet, François; Brousse, Emmanuel; Carel, Jean-Louis; Cottenye, Justine; Harmann, David; Joncour, Marc; Makhlouf, Houssine; Mouricaud, Daniel; Oussalah, Meihdi; Rodolfo, Jacques

2015-09-01

The Spectral Separation Assembly is a key component of the Flexible Combined Imager, an instrument that will be on-board Meteosat Third Generation. It splits the input beam coming from the telescope into five spectral groups, for a total of 16 channels, from 0.4 to 13.3 μm. It comprises a set of four dichroics separators followed by four collimating optics for the infrared spectral groups, which feed the cold imaging optics. The visible spectral group is directly imaged on a detector. This paper presents the optical design of the assembly, the mechanical mounting of the optical components, and the coatings developed for the dichroics, mirrors and lenses.

A solution for automatic parallelization of sequential assembly code

Directory of Open Access Journals (Sweden)

Kovačević Đorđe

2013-01-01

Full Text Available Since modern multicore processors can execute existing sequential programs only on a single core, there is a strong need for automatic parallelization of program code. Relying on existing algorithms, this paper describes one new software solution tool for parallelization of sequential assembly code. The main goal of this paper is to develop the parallelizator which reads sequential assembler code and at the output provides parallelized code for MIPS processor with multiple cores. The idea is the following: the parser translates assembler input file to program objects suitable for further processing. After that the static single assignment is done. Based on the data flow graph, the parallelization algorithm separates instructions on different cores. Once sequential code is parallelized by the parallelization algorithm, registers are allocated with the algorithm for linear allocation, and the result at the end of the program is distributed assembler code on each of the cores. In the paper we evaluate the speedup of the matrix multiplication example, which was processed by the parallelizator of assembly code. The result is almost linear speedup of code execution, which increases with the number of cores. The speed up on the two cores is 1.99, while on 16 cores the speed up is 13.88.

Pump/heat exchanger assembly for pool-type reactor

International Nuclear Information System (INIS)

Nathenson, R.D.; Slepian, R.M.

1989-01-01

This patent describes a heat exchanger and pump assembly for transferring thermal energy from a heated, first electrically conductive fluid to a pumped, second electrically conductive fluid and for transferring internal energy from the pumped, second electrically conductive fluid to the first electrically conductive fluid, the assembly adapted to be disposed within a pool of the first electrically conductive fluid and comprising: a heat exchanger comprising means for defining a first annularly shaped cavity for receiving a flow of the second electrically conductive fluid and a plurality of tubes disposed within the cavity, whereby the second electrically conductive fluid in the cavity is heated, each of the tubes having an input and an output end. The input ends being disposed at the top of the heat exchanger for receiving from the pool a flow of the first electrically conductive fluid therein. The output ends being disposed at the bottom of and free of the cavity defining means for discharging the first electrically conductive fluid directly into the pool; a pump disposed beneath the heat exchanger and comprised of a plurality of flow couplers disposed in a circular array, each flow coupler comprised of a pump duct for receiving the first electrically conductive fluid and a generator duct for receiving the second electrically conductive fluid

Assembly of the 30S subunit from Escherichia coli ribosomes occurs via two assembly domains which are initiated by S4 and S7

International Nuclear Information System (INIS)

Nowotny, V.; Nierhaus, K.H.

1988-01-01

A protein which initiates assembly of ribosomes is defined as a protein which binds to the respective rRNA without cooperativity (i.e., without the help of other proteins) during the onset of assembly and is essential for the formation of active ribosomal subunits. The number of proteins binding without cooperativity was determined by monitoring the reconstitution output of active particles at various inputs of 16S rRNA, in the present of constant amounts of 30S-derived proteins (TP30): This showed that only two of the proteins of the 30S subunit are assembly-initiator proteins. These two proteins are still present on a LiCl core particle comprising 16S rRNA and 12 proteins (including minor proteins). The 12 proteins were isolated, and a series of reconstitution experiments at various levels of rRNA excess demonstrated that S4 and S7 are the initiator proteins. Pulse-chase experiments performed during the early assembly with 14 C- and 3 H-labeled TP30 and the determination of the 14 C/ 3 H ratio of the individual proteins within the assembled particles revealed a bilobal structure of the 30S assembly: A group of six proteins headed by S4 (namely, S4, S20, S16, S15, S6, and S18) resisted the chasing most efficiently (S4 assembly domain). None of the proteins depending on S7 during assembly were found in this group but rather in a second group with intermediate chasing stability [S7 assembly domain; consisting of S7, S9, (S8), S19, and S3]. A number of proteins could be fully chased during the early assembly and therefore represent late assembly proteins (S10, S5, S13, S2, S21, S1). These findings fit well with the 30S assembly map. These data, together with the assembly map, imply that S8 and S5 play an important role in the interconnection of the two assembly domains

Logical NAND and NOR Operations Using Algorithmic Self-assembly of DNA Molecules

Science.gov (United States)

Wang, Yanfeng; Cui, Guangzhao; Zhang, Xuncai; Zheng, Yan

DNA self-assembly is the most advanced and versatile system that has been experimentally demonstrated for programmable construction of patterned systems on the molecular scale. It has been demonstrated that the simple binary arithmetic and logical operations can be computed by the process of self assembly of DNA tiles. Here we report a one-dimensional algorithmic self-assembly of DNA triple-crossover molecules that can be used to execute five steps of a logical NAND and NOR operations on a string of binary bits. To achieve this, abstract tiles were translated into DNA tiles based on triple-crossover motifs. Serving as input for the computation, long single stranded DNA molecules were used to nucleate growth of tiles into algorithmic crystals. Our method shows that engineered DNA self-assembly can be treated as a bottom-up design techniques, and can be capable of designing DNA computer organization and architecture.

Analysis of the Retained Gas Sample (RGS) Extruder Assembly

International Nuclear Information System (INIS)

Coverdell, B.L.

1995-09-01

In order for the Retained Gas Sample (RGS) Extruder Assembly to be safely used it was determined by the cognizant engineer that analysis was necessary. The use of the finite-element analysis (FEA) progarm COSMOS/M version 1.71 permitted a quick, easy, and detailed stress analysis of the RGS Extruder Assembly. The FEA model is a three dimensional model using the SHELL4T element type. From the results of the FEA, the cognizant engineer determined that the RGS extruder would be rated at 10,000 lbf and load tested to 12,000 lbf. The respective input and output files for the model are EXTR02.GFM and EXTR02.OUT and can be found on the attached tape

Dynamics of nuclear fuel assemblies in vertical flow channels

International Nuclear Information System (INIS)

Mason, V.A.

1988-01-01

DYNMOD is a computer program designed to predict the dynamic behaviour of nuclear fuel assemblies in axial flow. The calculations performed by DYNMOD and the input data required by the program are described in this report. Examples of DYNMOD usage and a brief assessment of the accuracy of the dynamic model are also presented. It is intended that the report will be used as a reference manual by users of DYNMOD

Vibrational characterization of hexagonal duct core assemblies under various support conditions

International Nuclear Information System (INIS)

Bartholf, L.W.; Julyk, L.J.; Ryan, J.A.

1989-03-01

Analysis of the dynamic response of advanced Liquid Metal Reactor (LMR) core internals to seismic excitation requires a significant number of simplifying assumptions and idealizations to economically meet the constraints of present-day computer limitations. Fluid coupling and nonlinearities associated with inter-assembly lateral support stiffness and clearances of a large cluster of core internal assemblies are some of the factors that complicate the analytical procedure (Moran, 1976). Well defined test data were needed to quantify these and other uncertainties associated with the use of analytical or numerical computer codes used in the seismic design and analysis of reactor cores. The purpose of the present experimental program was to supplement existing data, such as reported in (Sasaki and Muto, 1983), by developing vibrational characteristics of core assemblies over a range of parameters relative to LMR conceptual designs. The parameters selected for this program were variations in number and location of restraints, restraint-pad to duct-load-pad clearances, and input forcing frequency and g-level. Feature tests were conducted to characterize load pad stiffness and coefficient of restitution, and to calibrate load pads to measure inter-assembly across-flat impact loads. Simulated full-size LMR hexagonal duct core assemblies were used in vibration tests. A single assembly and a row of five assemblies were tested in air to establish modal characteristics and forced response behavior. 2 refs., 7 figs., 1 tab

On scaling laws for modelling the steam/water flow in a 'Dodewaard' fuel-assembly using Freon-12

International Nuclear Information System (INIS)

Graaf, R. van de; Mudde, R.F.; Hagen, T.H.J.J. van der.

1991-09-01

To stimulate the steam/water flow behaviour in a fuel assembly as present in the boiling water reactor at Dodewaard, Freon-12 is used as a modelling fluid. Scaling criteria are elaborated using dimensional analysis as a fluid-to-fluid modelling technique. When scaling is emphasized on void-fraction distribution and flow-regime transitions it is found that an approximately half-scale geometry for the Freon-model should be used. Together with the low latent heat of vaporization of Freon-12 this reduces the total required heat input significantly to be only 2% of the required heat input in a 'Dodewaard' fuel-assembly. Finally, working pressure (and saturation temperature) can also be brought to a convenient level. (author). 16 refs., 11 figs., 1 tab

A sectional-splinting technique for impressing multiple implant units by eliminating the use of an open tray

Directory of Open Access Journals (Sweden)

Suryakant C. Deogade

2014-01-01

Full Text Available Since the inception of root form implant dentistry by P-I Branemark in the early 1980′s, so many technical advances have been put forward by several authors. However, the open tray impression technique is still performed for impressing multiple implant fixtures as it was first described in the original Branemark procedure manual. The most critical aspect for a successful implant-supported restoration is the passive and an accurate fit of superstructures to avoid preload and loading stresses. Splinting impression technique in multiple implants has gained popularity. Auto-polymerizing acrylic resin is among the most routinely practiced splinting material for multiple implant units. However, unfortunately, it exhibits shrinkage, which makes an impression quite inaccurate. This case report presents the solution to minimize the shrinkage of resin by utilizing sectional-splinting technique as advocated in the previous implant literature.

A Framework for the Development of Automatic DFA Method to Minimize the Number of Components and Assembly Reorientations

Science.gov (United States)

Alfadhlani; Samadhi, T. M. A. Ari; Ma’ruf, Anas; Setiasyah Toha, Isa

2018-03-01

Assembly is a part of manufacturing processes that must be considered at the product design stage. Design for Assembly (DFA) is a method to evaluate product design in order to make it simpler, easier and quicker to assemble, so that assembly cost is reduced. This article discusses a framework for developing a computer-based DFA method. The method is expected to aid product designer to extract data, evaluate assembly process, and provide recommendation for the product design improvement. These three things are desirable to be performed without interactive process or user intervention, so product design evaluation process could be done automatically. Input for the proposed framework is a 3D solid engineering drawing. Product design evaluation is performed by: minimizing the number of components; generating assembly sequence alternatives; selecting the best assembly sequence based on the minimum number of assembly reorientations; and providing suggestion for design improvement.

Self-Assembling Molecular Logic Gates Based on DNA Crossover Tiles.

Science.gov (United States)

Campbell, Eleanor A; Peterson, Evan; Kolpashchikov, Dmitry M

2017-07-05

DNA-based computational hardware has attracted ever-growing attention due to its potential to be useful in the analysis of complex mixtures of biological markers. Here we report the design of self-assembling logic gates that recognize DNA inputs and assemble into crossover tiles when the output signal is high; the crossover structures disassemble to form separate DNA stands when the output is low. The output signal can be conveniently detected by fluorescence using a molecular beacon probe as a reporter. AND, NOT, and OR logic gates were designed. We demonstrate that the gates can connect to each other to produce other logic functions. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Improvement of flame resistance of non-flame retardant cables by applying fire protection measures

International Nuclear Information System (INIS)

Takemura, Yujiro; Segoshi, Yoshinori; Jinno, Susumu; Mii, Kazuki

2017-01-01

The new regulatory requirements, which were put in force after the Fukushima Daiichi accident, impose the use of flame retardant cables on the plant components having safety functions for the purpose of fire protection. However, some Japanese nuclear power plants built in the early days use non-flame retardant cables that do not pass the demonstration test to check for the flame resistance. To cope with the new regulatory requirements, a fire protection measure for non-flame retardant cables was introduced to assure flame resistance of non-flame retardant cables equivalent to or higher than that of flame retardant cables. To illustrate the fire protection measure, both non-flame retardant cables and its cable tray are covered with fire protection sheet fabricated from incombustible material to form an assembly. Considering the demonstration test results, it can be concluded that flame resistance performance of non-flame retardant cables equivalent to or higher than that of flame retardant cables can be assured by forming the assembly even if an external fire outside the assembly and internal cable fire inside the assembly are assumed. This paper introduces the design of the assembly consisting of a bundle of cables and a cable tray and summarizes the results of demonstration tests. (author)

Exergetic performance analyses of drying of broccoli florets in a tray drier

International Nuclear Information System (INIS)

Zafer Erbay

2009-01-01

At present, the drying process is one of the major procedures of food preservation and an important unit operation in a wide variety of food industries. Recently, drying of vegetables is of a particular interest because it is added to various ready-to-eat meals in order to improve their nutritional quality due to health benefit compounds present in vegetables (vitamins, phytochemicals, dietary fibers). Broccoli has been described as a vegetable with a high nutritional value due to its important content of vitamins, antioxidants and anti-carcinogenic compounds. Broccoli dehydration has not been investigated to a great extent and a few data are available in the open literature. In this study, broccoli florets were dried in a tray drier at a temperature range of 50-70 deg C with an air velocity range of 0.5-1.5 m/s. The performance of the process and system was evaluated using the exergy analysis method. Based on the experimental data, effects of the drying air temperature and the velocity on the performance of the drying process were discussed. It was obtained that the exergy evaporation rate and the exergetic efficiency of the process were obtained to vary between 0.0006-0.0029 kW and 0.27-1.16%, respectively. They increased as the drying air temperature increased, while the exergetic efficiency decreased with the rise in the drying air velocity. (author)

Analysis of irradiation temperature in fuel rods of OGL-1 fuel assembly

International Nuclear Information System (INIS)

Fukuda, Kousaku; Kobayashi, Fumiaki; Minato, Kazuo; Ikawa, Katsuichi; Iwamoto, Kazumi

1984-10-01

Irradiation temperature in the fuel rods of 5th OGL-1 fuel assembly was analysed by the system composed by STPDSP2 and TRUMP codes. As the measured input-data, following parameters were allowed for; circumferential heating distribution around the fuel rod, which was measured in the JMTR critical assembly, axial heating distribution through the fuel rod, ratio of peak heatings of three fuel rods, and pre- and post-irradiation outer radii of the fuel compacts and inner radii of the graphite sleeves, which had been measured in PIE of the 5th OGL-1 fuel assembly. In computation the axial distributions of helium coolant temperature through the fuel rod and the heating value of each fuel rod were, firstly, calculated as input data for TRUMP. The TRUMP calculation yielded the temperatures which were fitted in those measured by all of the thermo-couples installed in the fuel rods, by adjusting only the value of the surface heat transfer coefficient, and consequently, the temperatures in all portions of the fuel rod were obtained. The apparent heat transfer coefficient changed to 60% of the initial values in the middle period of irradiation. For this reduction it was deduced that shoot had covered the surface of the fuel rod during irradiation, which was confirmed in PIE. Beside it, several things were found in this analysis. (author)

A model of stimulus-specific neural assemblies in the insect antennal lobe.

Directory of Open Access Journals (Sweden)

Dominique Martinez

2008-08-01

Full Text Available It has been proposed that synchronized neural assemblies in the antennal lobe of insects encode the identity of olfactory stimuli. In response to an odor, some projection neurons exhibit synchronous firing, phase-locked to the oscillations of the field potential, whereas others do not. Experimental data indicate that neural synchronization and field oscillations are induced by fast GABA(A-type inhibition, but it remains unclear how desynchronization occurs. We hypothesize that slow inhibition plays a key role in desynchronizing projection neurons. Because synaptic noise is believed to be the dominant factor that limits neuronal reliability, we consider a computational model of the antennal lobe in which a population of oscillatory neurons interact through unreliable GABA(A and GABA(B inhibitory synapses. From theoretical analysis and extensive computer simulations, we show that transmission failures at slow GABA(B synapses make the neural response unpredictable. Depending on the balance between GABA(A and GABA(B inputs, particular neurons may either synchronize or desynchronize. These findings suggest a wiring scheme that triggers stimulus-specific synchronized assemblies. Inhibitory connections are set by Hebbian learning and selectively activated by stimulus patterns to form a spiking associative memory whose storage capacity is comparable to that of classical binary-coded models. We conclude that fast inhibition acts in concert with slow inhibition to reformat the glomerular input into odor-specific synchronized neural assemblies.

TMI cable tracer operation and maintenance manual for assembly 417910

International Nuclear Information System (INIS)

Sumstine, R.L.

1983-11-01

This manual provides technical information and instructions to operate and maintain the cable tracer designed for the Three Mile Island (TMI) Unit 2 Reactor Building. The TMI cable tracer was developed to allow TMI personnel to trace cables in cable trays that may be tested or sectioned for destructive examination

The effect of long-term changes in plant inputs on soil carbon stocks

Science.gov (United States)

Georgiou, K.; Li, Z.; Torn, M. S.

2017-12-01

Soil organic carbon (SOC) is the largest actively-cycling terrestrial reservoir of C and an integral component of thriving natural and managed ecosystems. C input interventions (e.g., litter removal or organic amendments) are common in managed landscapes and present an important decision for maintaining healthy soils in sustainable agriculture and forestry. Furthermore, climate and land-cover change can also affect the amount of plant C inputs that enter the soil through changes in plant productivity, allocation, and rooting depth. Yet, the processes that dictate the response of SOC to such changes in C inputs are poorly understood and inadequately represented in predictive models. Long-term litter manipulations are an invaluable resource for exploring key controls of SOC storage and validating model representations. Here we explore the response of SOC to long-term changes in plant C inputs across a range of biomes and soil types. We synthesize and analyze data from long-term litter manipulation field experiments, and focus our meta-analysis on changes to total SOC stocks, microbial biomass carbon, and mineral-associated (`protected') carbon pools and explore the relative contribution of above- versus below-ground C inputs. Our cross-site data comparison reveals that divergent SOC responses are observed between forest sites, particularly for treatments that increase C inputs to the soil. We explore trends among key variables (e.g., microbial biomass to SOC ratios) that inform soil C model representations. The assembled dataset is an important benchmark for evaluating process-based hypotheses and validating divergent model formulations.

Nonlinear Modeling by Assembling Piecewise Linear Models

Science.gov (United States)

Yao, Weigang; Liou, Meng-Sing

2013-01-01

To preserve nonlinearity of a full order system over a parameters range of interest, we propose a simple modeling approach by assembling a set of piecewise local solutions, including the first-order Taylor series terms expanded about some sampling states. The work by Rewienski and White inspired our use of piecewise linear local solutions. The assembly of these local approximations is accomplished by assigning nonlinear weights, through radial basis functions in this study. The efficacy of the proposed procedure is validated for a two-dimensional airfoil moving at different Mach numbers and pitching motions, under which the flow exhibits prominent nonlinear behaviors. All results confirm that our nonlinear model is accurate and stable for predicting not only aerodynamic forces but also detailed flowfields. Moreover, the model is robustness-accurate for inputs considerably different from the base trajectory in form and magnitude. This modeling preserves nonlinearity of the problems considered in a rather simple and accurate manner.

Modelamiento de la cinética de secado de lúcuma (Pouteria lucuma)

OpenAIRE

Barrena Gurbillón, Miguel Angel

2011-01-01

Pouteria lucuma "eggfruit”, is a fruit sold fresh and dry as an input to confectionery and food industry. This study determined the parameters necessary to design a tray dryer with hot air for production eggfruit flour, being used for this fresh eggfruit physiological maturity and with good sanitary conditions. The pulp was cut into slices 0,3 cm thick and placed in a laboratory tray dryer with hot air. Three temperatures were tested for air drying (40 ºC, 50 ºC and 60 ºC) and three air speed...

Stackable Form-Factor Peripheral Component Interconnect Device and Assembly

Science.gov (United States)

Somervill, Kevin M. (Inventor); Ng, Tak-kwong (Inventor); Torres-Pomales, Wilfredo (Inventor); Malekpour, Mahyar R. (Inventor)

2013-01-01

A stackable form-factor Peripheral Component Interconnect (PCI) device can be configured as a host controller or a master/target for use on a PCI assembly. PCI device may comprise a multiple-input switch coupled to a PCI bus, a multiplexor coupled to the switch, and a reconfigurable device coupled to one of the switch and multiplexor. The PCI device is configured to support functionality from power-up, and either control function or add-in card function.

Development of evaluation methodology to assess the sodium fire suppression performance of leak collection tray

International Nuclear Information System (INIS)

Parida, F.C.; Rao, P.M.; Ramesh, S.S.; Somayajulu, P.A.; Malarvizhi, B.; Kannan, S.E.

2005-01-01

Full text of publication follows: Leakage of hot liquid sodium and its subsequent combustion in the form of a pool cannot be completely ruled out in a Fast breeder Reactor (FBR) plant in spite of provision for adequate safety measures. To protect the plant system from the hazardous effects of flame, heat and smoke, one of the passive protection devices used in FBR plants is the Leak Collection Tray (LCT). The design of LCT is based on immediate channeling of burning liquid sodium on the funnel shaped sloping cover tray (SCT) to the bottom sodium hold-up vessel (SHV) in which self-extinction of the fire occurs due to oxygen starvation. The SCT has one or three drain pipes and air vent pipes depending on the type of design. In each experiment, a known amount ranging from 30 to 40 kg of hot liquid sodium at 550 deg. C was discharged on the LCT in the open air. Continuous on-line monitoring of temperature at strategic locations (∼ 28 points) was carried out. Colour video-graphy was employed for taking motion pictures of various time-dependent events like sodium dumping, appearance of flame and release of smoke through vent pipes. After self-extinction of sodium fire, the LCT was allowed to cool overnight in an argon atmosphere. Solid samples of sodium debris in the SCT and SHV were collected by manual core drilling machine. The samples were subjected to chemical analysis for determination of unburnt and burnt sodium. The sodium debris removed from SCT and SHV were separately weighed. To assess the performance of the LCT, two different geometrical configurations of SCT, one made up of stainless steel an the other of carbon steel, were used. Three broad phenomena are identified as the basis of evaluation methodology. These are (a) thermal transients, i.e. heating and cooling of the bulk sodium in SCT and SHV respectively, (b) post test sodium debris distribution between SCT and SHV as well as (c) sodium combustion and smoke release behaviour. Under each category

Development of evaluation methodology to assess the sodium fire suppression performance of leak collection tray

Energy Technology Data Exchange (ETDEWEB)

Parida, F.C.; Rao, P.M.; Ramesh, S.S.; Somayajulu, P.A.; Malarvizhi, B.; Kannan, S.E. [Engineering Safety Division, Safety Group, Indira Gandhi Centre for Atomic Research, Kalpakkam - 603102, Tamilnadu (India)

2005-07-01

Full text of publication follows: Leakage of hot liquid sodium and its subsequent combustion in the form of a pool cannot be completely ruled out in a Fast breeder Reactor (FBR) plant in spite of provision for adequate safety measures. To protect the plant system from the hazardous effects of flame, heat and smoke, one of the passive protection devices used in FBR plants is the Leak Collection Tray (LCT). The design of LCT is based on immediate channeling of burning liquid sodium on the funnel shaped sloping cover tray (SCT) to the bottom sodium hold-up vessel (SHV) in which self-extinction of the fire occurs due to oxygen starvation. The SCT has one or three drain pipes and air vent pipes depending on the type of design. In each experiment, a known amount ranging from 30 to 40 kg of hot liquid sodium at 550 deg. C was discharged on the LCT in the open air. Continuous on-line monitoring of temperature at strategic locations ({approx} 28 points) was carried out. Colour video-graphy was employed for taking motion pictures of various time-dependent events like sodium dumping, appearance of flame and release of smoke through vent pipes. After self-extinction of sodium fire, the LCT was allowed to cool overnight in an argon atmosphere. Solid samples of sodium debris in the SCT and SHV were collected by manual core drilling machine. The samples were subjected to chemical analysis for determination of unburnt and burnt sodium. The sodium debris removed from SCT and SHV were separately weighed. To assess the performance of the LCT, two different geometrical configurations of SCT, one made up of stainless steel an the other of carbon steel, were used. Three broad phenomena are identified as the basis of evaluation methodology. These are (a) thermal transients, i.e. heating and cooling of the bulk sodium in SCT and SHV respectively, (b) post test sodium debris distribution between SCT and SHV as well as (c) sodium combustion and smoke release behaviour. Under each category

Pilot Fullerton plans menu as packaged food and beverages float around him

Science.gov (United States)

1982-01-01

Pilot C. Gordon Fullerton, wearing the communications carrier assembly (ASSY) mini headset (HDST), beings food preparation on the middeck. Canned goods, sealed packages, beverage containers, etc are attached with velcro to meal tray assemblies (secured on middeck forward lockers) and freefloat around Fullerton. JSC water dispenser kit and portrait of G.W.S. Abbey appears behind Fullerton on port side bulkhead and potable water tank appears below him.

TART input manual

International Nuclear Information System (INIS)

Kimlinger, J.R.; Plechaty, E.F.

1982-01-01

The TART code is a Monte Carlo neutron/photon transport code that is only on the CRAY computer. All the input cards for the TART code are listed, and definitions for all input parameters are given. The execution and limitations of the code are described, and input for two sample problems are given

SOLVING OPTIMAL ASSEMBLY LINE CONFIGURATION TASK BY MULTIOBJECTIVE DECISION MAKING METHODS

Directory of Open Access Journals (Sweden)

Ján ČABALA

2017-06-01

Full Text Available This paper deals with looking for the optimal configuration of automated assembly line model placed within Department of Cybernetics and Artificial Intelligence (DCAI. In order to solve this problem, Stateflow model of each configuration was created to simulate the behaviour of particular assembly line configuration. Outputs from these models were used as inputs into the multiobjective decision making process. Multi-objective decision-making methods were subsequently used to find the optimal configuration of assembly line. Paper describes the whole process of solving this task, from building the models to choosing the best configuration. Specifically, the problem was resolved using the experts’ evaluation method for evaluating the weights of every decision-making criterion, while the ELECTRE III, TOPSIS and AGREPREF methods were used for ordering the possible solutions from the most to the least suitable alternative. Obtained results were compared and final solution of this multi-objective decisionmaking problem is chosen.

Measurement of Laser Weld Temperatures for 3D Model Input

Energy Technology Data Exchange (ETDEWEB)

Dagel, Daryl [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grossetete, Grant [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Maccallum, Danny O. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-10-01

Laser welding is a key joining process used extensively in the manufacture and assembly of critical components for several weapons systems. Sandia National Laboratories advances the understanding of the laser welding process through coupled experimentation and modeling. This report summarizes the experimental portion of the research program, which focused on measuring temperatures and thermal history of laser welds on steel plates. To increase confidence in measurement accuracy, researchers utilized multiple complementary techniques to acquire temperatures during laser welding. This data serves as input to and validation of 3D laser welding models aimed at predicting microstructure and the formation of defects and their impact on weld-joint reliability, a crucial step in rapid prototyping of weapons components.

78 FR 79391 - Foreign-Trade Zone (FTZ) 22-Chicago, Illinois, Notification of Proposed Production Activity...

Science.gov (United States)

2013-12-30

... and nut assemblies; hex, lock and push nuts; lock washers; spring washers; washer packages; rivets; E... plates; oven crumb trays; rubber feet; slow cooker lids; water filter holders; electromagnetic...; washers; shoulder rivets; cotter pins; E-rings; latch, pedal, coil and torque springs; wire racks; bake...

Exact algorithms for haplotype assembly from whole-genome sequence data.

Science.gov (United States)

Chen, Zhi-Zhong; Deng, Fei; Wang, Lusheng

2013-08-15

Haplotypes play a crucial role in genetic analysis and have many applications such as gene disease diagnoses, association studies, ancestry inference and so forth. The development of DNA sequencing technologies makes it possible to obtain haplotypes from a set of aligned reads originated from both copies of a chromosome of a single individual. This approach is often known as haplotype assembly. Exact algorithms that can give optimal solutions to the haplotype assembly problem are highly demanded. Unfortunately, previous algorithms for this problem either fail to output optimal solutions or take too long time even executed on a PC cluster. We develop an approach to finding optimal solutions for the haplotype assembly problem under the minimum-error-correction (MEC) model. Most of the previous approaches assume that the columns in the input matrix correspond to (putative) heterozygous sites. This all-heterozygous assumption is correct for most columns, but it may be incorrect for a small number of columns. In this article, we consider the MEC model with or without the all-heterozygous assumption. In our approach, we first use new methods to decompose the input read matrix into small independent blocks and then model the problem for each block as an integer linear programming problem, which is then solved by an integer linear programming solver. We have tested our program on a single PC [a Linux (x64) desktop PC with i7-3960X CPU], using the filtered HuRef and the NA 12878 datasets (after applying some variant calling methods). With the all-heterozygous assumption, our approach can optimally solve the whole HuRef data set within a total time of 31 h (26 h for the most difficult block of the 15th chromosome and only 5 h for the other blocks). To our knowledge, this is the first time that MEC optimal solutions are completely obtained for the filtered HuRef dataset. Moreover, in the general case (without the all-heterozygous assumption), for the HuRef dataset our

Input-output supervisor

International Nuclear Information System (INIS)

Dupuy, R.

1970-01-01

The input-output supervisor is the program which monitors the flow of informations between core storage and peripheral equipments of a computer. This work is composed of three parts: 1 - Study of a generalized input-output supervisor. With sample modifications it looks like most of input-output supervisors which are running now on computers. 2 - Application of this theory on a magnetic drum. 3 - Hardware requirement for time-sharing. (author) [fr

MOCA, Criticality of VVER Reactor Hexagonal Fuel Assemblies

International Nuclear Information System (INIS)

KYNCL, Jan

1994-01-01

1 - Description of program or function: Criticality problem in neutron transport for hexagonal fuel assembly in VVER nuclear reactor. The assembly is assumed to be either arranged in an infinite hexagonal array or placed in vacuum. The problem is solved in three- dimensional geometry, using standard energy group formalism and assuming that effective scattering cross sections are presented as Legendre polynomial expansions. The code evaluates ten different physical quantities, e.g. multiplication factor, neutron flux per energy group and spatial zone, integrated over angle and power in any zone of the assembly. 2 - Method of solution: Monte Carlo method of successive generations is applied. Computation proceeds according to an analog random process. The code is organized into three blocks: In the first block, the input data are converted to quantities for use in the Monte Carlo calculation. An initial neutron distribution is calculated, which corresponds to a fission spectrum uniform in spatial and angular variables. The main calculations are carried out in the second block (subroutine PROC2). This block is subdivided into geometrical and physical parts. Neutron tracks in individual zones and groups as well as probabilities for the formation of secondary neutrons are calculated. In the third block (subroutine PROC3), the results are evaluated statistically. Effective multiplication coefficients, the neutron flux per group and zone, and respective errors are computed. These quantities serve as a basis for the evaluation of other quantities. The results are either printed or stored for future evaluations. 3 - Restrictions on the complexity of the problem: In the PC version of the program, the maximum number of neutrons is 1000, the maximum number of energy groups is 4, and the maximum number of material compositions is 15. Angular expansion of scattering cross sections is allowed up to P10. These restrictions can easily be removed by increasing input parameters and

Demonstration of a High-Order Mode Input Coupler for a 220-GHz Confocal Gyrotron Traveling Wave Tube

Science.gov (United States)

Guan, Xiaotong; Fu, Wenjie; Yan, Yang

2018-02-01

A design of high-order mode input coupler for 220-GHz confocal gyrotron travelling wave tube is proposed, simulated, and demonstrated by experimental tests. This input coupler is designed to excite confocal TE 06 mode from rectangle waveguide TE 10 mode over a broadband frequency range. Simulation results predict that the optimized conversion loss is about 2.72 dB with a mode purity excess of 99%. Considering of the gyrotron interaction theory, an effective bandwidth of 5 GHz is obtained, in which the beam-wave coupling efficiency is higher than half of maximum. The field pattern under low power demonstrates that TE 06 mode is successfully excited in confocal waveguide at 220 GHz. Cold test results from the vector network analyzer perform good agreements with simulation results. Both simulation and experimental results illustrate that the reflection at input port S11 is sensitive to the perpendicular separation of two mirrors. It provides an engineering possibility for estimating the assembly precision.

Environmental Tests of the Flight GLAST LAT Tracker Towers

Energy Technology Data Exchange (ETDEWEB)

Bagagli, R.; Baldini, L.; Bellazzini, R.; Barbiellini, G.; Belli, F.; Borden, T.; Brez, A.; Brigida, M.; Caliandro, G.A.; Cecchi, C.; Cohen-Tanugi, J.; Angelis, A.De; Drell, P.; Favuzzi, C.; Fusco, P.; Gargano, F.; Germani, S.; Giglietto, N.; Giordano, F.; Goodman, J.; Himel, T.

2008-03-12

The Gamma-ray Large Area Space telescope (GLAST) is a gamma-ray satellite scheduled for launch in 2008. Before the assembly of the Tracker subsystem of the Large Area Telescope (LAT) science instrument of GLAST, every component (tray) and module (tower) has been subjected to extensive ground testing required to ensure successful launch and on-orbit operation. This paper describes the sequence and results of the environmental tests performed on an engineering model and all the flight hardware of the GLAST LAT Tracker. Environmental tests include vibration testing, thermal cycles and thermal-vacuum cycles of every tray and tower as well as the verification of their electrical performance.

Production of tomato seedlings using different substrates and trays in three protected environments Produção de mudas de tomate usando-se diferentes substratos e tipos de bandejas em três ambientes protegidos

Directory of Open Access Journals (Sweden)

Edilson Costa

2012-10-01

Full Text Available The seedlings production is an essential part for vegetables production. Thus, this study aimed to evaluate the environment, the substrates and the containers in the development of tomato seedlings, cv. Santa crus Kada Gigante, in Aquidauana -MS, Brazil region, from October to November, 2008. Polystyrene trays with 72; 128 and 200 cells, filled with four substrates (soil; Plantmax®; coconut fiber and vermiculite were tested in three protected environments (greenhouse; screened with Sombrite® and screened with Aluminet®. The experimental design was completely randomized, factorial scheme 3x4 (three trays x four substrates, with four replications, being analyzed individual variance analysis and joint analysis for the environments. The environment with screens (Sombrite® and Aluminet®, the trays with 72 cells and the vermiculite produced better results.A produção de mudas é uma etapa essencial na cadeia produtiva de hortaliças. Desta forma, este trabalho teve os objetivos de avaliar a ambiência, os substratos e os recipientes no desenvolvimento de mudas de tomateiro, cv. Santa Cruz Kada Gigante, na região de Aquidauana-MS, de outubro a novembro de 2008. Foram testadas bandejas de poliestireno com 72; 128 e 200 células, preenchidas com quatro substratos: solo; Plantmax®; fibra de coco fina, e vermiculita, em três ambientes protegidos: estufa, telado com Sombrite® e telado com Aluminet®. O experimento foi conduzido em delineamento inteiramente casualizado, em esquema fatorial 3 x 4 (três bandejas x quatro substratos, com quatro repetições, realizando-se de análises de variâncias individuais e análise conjunta dos ambientes. Os ambientes telados (Sombrite® e Aluminet®, a bandeja com 72 células e a vermiculita produziram as melhores mudas.

Reliability of CGA/LGA/HDI Package Board/Assembly (Final Report)

Science.gov (United States)

Ghaffaroam. Reza

2014-01-01

Package manufacturers are now offering commercial-off-the-shelf column grid array (COTS CGA) packaging technologies in high-reliability versions. Understanding the process and quality assurance (QA) indicators for reliability are important for low-risk insertion of these advanced electronics packages. The previous reports, released in January of 2012 and January of 2013, presented package test data, assembly information, and reliability evaluation by thermal cycling for CGA packages with 1752, 1517, 1509, and 1272 inputs/outputs (I/Os) and 1-mm pitch. It presented the thermal cycling (-55C either 100C or 125C) test results for up to 200 cycles. This report presents up to 500 thermal cycles with quality assurance and failure analysis evaluation represented by optical photomicrographs, 2D real time X-ray images, dye-and-pry photomicrographs, and optical/scanning electron Microscopy (SEM) cross-sectional images. The report also presents assembly challenge using reflowing by either vapor phase or rework station of CGA and land grid array (LGA) versions of three high I/O packages both ceramic and plastic configuration. A new test vehicle was designed having high density interconnect (HDI) printed circuit board (PCB) with microvia-in-pad to accommodate both LGA packages as well as a large number of fine pitch ball grid arrays (BGAs). The LGAs either were assembled onto HDI PCB as an LGA or were solder paste print and reflow first to form solder dome on pads before assembly. Both plastic BGAs with 1156 I/O and ceramic LGAs were assembled. It also presented the X-ray inspection results as well as failures due to 200 thermal cycles. Lessons learned on assembly of ceramic LGAs are also presented.

Manufacturing requirements of reactor assembly components for PFBR (Paper No. 041)

International Nuclear Information System (INIS)

Murty, C.G.K.; Bhoje, S.B.

1987-02-01

This paper enumerates the requirements of 500 MWe Prototype Fast Breeder Reactor (PFBR) components and considering the present state of art of Indian industry an analysis is made on the challenges to be faced in manufacture highlighting the areas needing development. The large sizes and weights of the components coupled with the limitations on shop facilities and ODC transport, demand part of the fabrication to be done at shop and balance assembly work as well as certain assembly machining operations to be done at site work shop. The stringent geometrical tolerances coupled with extensive destructive and non-destructive examinations call for balanced and low heat input welding techniques and special inspection equipment like electronic co-ordinate determination system. The present paper deals with the specific manufacturing problems of the main reactor components. (author)

A mathematical model of an automatic assembler to stack fuel pellets

International Nuclear Information System (INIS)

Jarvis, R.G.; Joynes, R.; Bretzlaff, C.I.

1980-11-01

Fuel elements for CANDU reactors are assembled from stacks of cylindrical UO 2 pellets, with close tolerances on lengths and diameters. Present stacking techniques involve extensive manual operations and they can be speeded up and reduced in cost by an automated device. If gamma-active fuel is handled such a device is essential. An automatic fuel pellet assembly process was modelled mathematically. The model indicated a suitable sequence of pellet manipulations to arrive at a stack length that was always within tolerance. This sequence was used as the inital input for the design of mechanical hardware. The mechanical design and the refinement of the mathematical model proceeded simultaneously. Mechanical constraints were allowed for in the model, and its optimized sequence of operations was incorporated in a microcomputer program to control the mechanical hardware. (auth)

Hybrid De Novo Genome Assembly Using MiSeq and SOLiD Short Read Data.

Directory of Open Access Journals (Sweden)

Tsutomu Ikegami

Full Text Available A hybrid de novo assembly pipeline was constructed to utilize both MiSeq and SOLiD short read data in combination in the assembly. The short read data were converted to a standard format of the pipeline, and were supplied to the pipeline components such as ABySS and SOAPdenovo. The assembly pipeline proceeded through several stages, and either MiSeq paired-end data, SOLiD mate-paired data, or both of them could be specified as input data at each stage separately. The pipeline was examined on the filamentous fungus Aspergillus oryzae RIB40, by aligning the assembly results against the reference sequences. Using both the MiSeq and the SOLiD data in the hybrid assembly, the alignment length was improved by a factor of 3 to 8, compared with the assemblies using either one of the data types. The number of the reproduced gene cluster regions encoding secondary metabolite biosyntheses (SMB was also improved by the hybrid assemblies. These results imply that the MiSeq data with long read length are essential to construct accurate nucleotide sequences, while the SOLiD mate-paired reads with long insertion length enhance long-range arrangements of the sequences. The pipeline was also tested on the actinomycete Streptomyces avermitilis MA-4680, whose gene is known to have high-GC content. Although the quality of the SOLiD reads was too low to perform any meaningful assemblies by themselves, the alignment length to the reference was improved by a factor of 2, compared with the assembly using only the MiSeq data.

Vibration analysis of reactor assembly internals for Prototype Fast Breeder Reactor

International Nuclear Information System (INIS)

Chellapandi, P.; Jalaldeen, S.; Srinivasan, R.; Chetal, S.C.; Bhoje, S.B.

2003-01-01

Vibration analysis of the reactor assembly components of 500 MWe Prototype Fast Breeder Reactor (PFBR) is presented. The vibration response of primary pump as well as dynamic forces developed at its supports are predicted numerically. The stiffness properties of hydrostatic bearing are determined by formulating and solving governing fluid and structural mechanics equations. The dynamic forces exerted by pump are used as input data for the dynamic response of reactor assembly components, mainly inner vessel, thermal baffle and control plug. Dynamic response of reactor assembly components is also predicted for the pressure fluctuations caused by sodium free level oscillations. Thermal baffle (weir shell) which is subjected to fluid forces developed at the associated sodium free levels is analysed by formulating and solving a set of non-linear equations for fluids, structures and fluid structure interaction (FSI). The control rod drive mechanism is analysed for response under flow induced forces on the parts subjected to cross flow in the zone just above the core top, taking into account FSI between sheaths of control and safety rod and absorber pin bundle. Based on the analysis results, it is concluded that the reactor assembly internals are free from any risk of mechanical as well as flow induced vibrations. (author)

Minimization of number of setups for mounting machines

Energy Technology Data Exchange (ETDEWEB)

Kolman, Pavel; Nchor, Dennis; Hampel, David [Department of Statistics and Operation Analysis, Faculty of Business and Economics, Mendel University in Brno, Zemědělská 1, 603 00 Brno (Czech Republic); Žák, Jaroslav [Institute of Technology and Business, Okružní 517/10, 370 01 České Budejovice (Czech Republic)

2015-03-10

The article deals with the problem of minimizing the number of setups for mounting SMT machines. SMT is a device used to assemble components on printed circuit boards (PCB) during the manufacturing of electronics. Each type of PCB has a different set of components, which are obligatory. Components are placed in the SMT tray. The problem consists in the fact that the total number of components used for all products is greater than the size of the tray. Therefore, every change of manufactured product requires a complete change of components in the tray (i.e., a setup change). Currently, the number of setups corresponds to the number of printed circuit board type. Any production change affects the change of setup and stops production on one shift. Many components occur in more products therefore the question arose as to how to deploy the products into groups so as to minimize the number of setups. This would result in a huge increase in efficiency of production.

ColloInputGenerator

DEFF Research Database (Denmark)

2013-01-01

This is a very simple program to help you put together input files for use in Gries' (2007) R-based collostruction analysis program. It basically puts together a text file with a frequency list of lexemes in the construction and inserts a column where you can add the corpus frequencies. It requires...... it as input for basic collexeme collostructional analysis (Stefanowitsch & Gries 2003) in Gries' (2007) program. ColloInputGenerator is, in its current state, based on programming commands introduced in Gries (2009). Projected updates: Generation of complete work-ready frequency lists....

WWER-440 fuel cycles possibilities using improved fuel assemblies design

International Nuclear Information System (INIS)

Mikolas, P.; Svarny, J.

2008-01-01

Practically five years cycle has been achieved in the last years at NPP Dukovany. There are two principal means how it could be achieved. First, it is necessary to use fuel assemblies with higher fuel enrichment and second, to use fuel loading with very low leakage. Both these conditions are fulfilled at NPP Dukovany at this time. It is known, that the fuel cycle economy can be improved by increasing the fuel residence time in the core up to six years. There are at least two ways how this goal could be achieved. The simplest way is to increase enrichment in fuel. There exists a limit, which is 5.0 w % of 235 U. Taking into account some uncertainty, the calculation maximum is 4.95 w % of 235 U. The second way is to change fuel assembly design. There are several possibilities, which seem to be suitable from the neutron - physical point of view. The first one is higher mass content of uranium in a fuel assembly. The next possibility is to enlarge pin pitch. The last possibility is to 'omit' FA shroud. This is practically unrealistic; anyway, some other structural parts must be introduced. The basic neutron physical characteristics of these cycles for up-rated power are presented showing that the possibilities of fuel assemblies with this improved design in enlargement of fuel cycles are very promising. In the end, on the basis of neutron physical characteristics and necessary economical input parameters, a preliminary evaluation of economic contribution of proposals of advanced fuel assemblies on fuel cycle economy is presented (Authors)

Reconfigurable assembly work station

Energy Technology Data Exchange (ETDEWEB)

Lin, Yhu-Tin; Abell, Jeffrey A.; Spicer, John Patrick

2017-11-14

A reconfigurable autonomous workstation includes a multi-faced superstructure including a horizontally-arranged frame section supported on a plurality of posts. The posts form a plurality of vertical faces arranged between adjacent pairs of the posts, the faces including first and second faces and a power distribution and position reference face. A controllable robotic arm suspends from the rectangular frame section, and a work table fixedly couples to the power distribution and position reference face. A plurality of conveyor tables are fixedly coupled to the work table including a first conveyor table through the first face and a second conveyor table through the second face. A vision system monitors the work table and each of the conveyor tables. A programmable controller monitors signal inputs from the vision system to identify and determine orientation of the component on the first conveyor table and control the robotic arm to execute an assembly task.

Robotically Assembled Aerospace Structures: Digital Material Assembly using a Gantry-Type Assembler

Science.gov (United States)

Trinh, Greenfield; Copplestone, Grace; O'Connor, Molly; Hu, Steven; Nowak, Sebastian; Cheung, Kenneth; Jenett, Benjamin; Cellucci, Daniel

2017-01-01

This paper evaluates the development of automated assembly techniques for discrete lattice structures using a multi-axis gantry type CNC machine. These lattices are made of discrete components called "digital materials." We present the development of a specialized end effector that works in conjunction with the CNC machine to assemble these lattices. With this configuration we are able to place voxels at a rate of 1.5 per minute. The scalability of digital material structures due to the incremental modular assembly is one of its key traits and an important metric of interest. We investigate the build times of a 5x5 beam structure on the scale of 1 meter (325 parts), 10 meters (3,250 parts), and 30 meters (9,750 parts). Utilizing the current configuration with a single end effector, performing serial assembly with a globally fixed feed station at the edge of the build volume, the build time increases according to a scaling law of n4, where n is the build scale. Build times can be reduced significantly by integrating feed systems into the gantry itself, resulting in a scaling law of n3. A completely serial assembly process will encounter time limitations as build scale increases. Automated assembly for digital materials can assemble high performance structures from discrete parts, and techniques such as built in feed systems, parallelization, and optimization of the fastening process will yield much higher throughput.

Sequence assembly

DEFF Research Database (Denmark)

Scheibye-Alsing, Karsten; Hoffmann, S.; Frankel, Annett Maria

2009-01-01

Despite the rapidly increasing number of sequenced and re-sequenced genomes, many issues regarding the computational assembly of large-scale sequencing data have remain unresolved. Computational assembly is crucial in large genome projects as well for the evolving high-throughput technologies and...... in genomic DNA, highly expressed genes and alternative transcripts in EST sequences. We summarize existing comparisons of different assemblers and provide a detailed descriptions and directions for download of assembly programs at: http://genome.ku.dk/resources/assembly/methods.html....

Bacteriophage Assembly

Directory of Open Access Journals (Sweden)

Anastasia A. Aksyuk

2011-02-01

Full Text Available Bacteriophages have been a model system to study assembly processes for over half a century. Formation of infectious phage particles involves specific protein-protein and protein-nucleic acid interactions, as well as large conformational changes of assembly precursors. The sequence and molecular mechanisms of phage assembly have been elucidated by a variety of methods. Differences and similarities of assembly processes in several different groups of bacteriophages are discussed in this review. The general principles of phage assembly are applicable to many macromolecular complexes.

Determining method and device for enrichment distribution inside of fuel assembly

International Nuclear Information System (INIS)

Hirano, Yasushi; Hida, Kazuki; Sakurada, Koichi.

1997-01-01

An enrichment degree at an initial burning stage of each of fuel rods of a BWR type reactor assembly is divided into groups. The enrichment degree at the initial burning stage of each of the groups is inputted, and the burning period from the loading to the taking out is divided into a plurality of burning steps. Nuclear characteristics of fuel assemblies such as the power of fuel rods, R-factor and infinite multiplication factor in each of the burning steps are estimated. The enrichment degree of the group of enrichment degree at the initial burning stage and the estimated power of fuel rods in a reactor operation state during the burning step are stored in the memory. A sensitivity coefficient showing the amount of change of the power of fuel rods in the burning step relative to the change of the enrichment degree of the group of enrichment degree is evaluated. A weighing function in the burning step is inputted. The maximum value of the product of the weighing function and the power of fuel rods throughout the entire burning steps is determined as an aimed function. Optimization calculation is conducted for determining the enrichment degree of the group so as to minimize the aimed function thereby determining the distribution of the enrichment degree. (N.H.)

A universal molecular translator for non-nucleic acid targets that enables dynamic DNA assemblies and logic operations.

Science.gov (United States)

Tang, Wei; Hu, Shichao; Wang, Huaming; Zhao, Yan; Li, Na; Liu, Feng

2014-11-28

A universal molecular translator based on the target-triggered DNA strand displacement was developed, which was able to convert various kinds of non-nucleic acid targets into a unique output DNA. This translation strategy was successfully applied in directing dynamic DNA assemblies and in realizing three-input logic gate operations.

Compensating Level-Dependent Frequency Representation in Auditory Cortex by Synaptic Integration of Corticocortical Input.

Directory of Open Access Journals (Sweden)

Max F K Happel

Full Text Available Robust perception of auditory objects over a large range of sound intensities is a fundamental feature of the auditory system. However, firing characteristics of single neurons across the entire auditory system, like the frequency tuning, can change significantly with stimulus intensity. Physiological correlates of level-constancy of auditory representations hence should be manifested on the level of larger neuronal assemblies or population patterns. In this study we have investigated how information of frequency and sound level is integrated on the circuit-level in the primary auditory cortex (AI of the Mongolian gerbil. We used a combination of pharmacological silencing of corticocortically relayed activity and laminar current source density (CSD analysis. Our data demonstrate that with increasing stimulus intensities progressively lower frequencies lead to the maximal impulse response within cortical input layers at a given cortical site inherited from thalamocortical synaptic inputs. We further identified a temporally precise intercolumnar synaptic convergence of early thalamocortical and horizontal corticocortical inputs. Later tone-evoked activity in upper layers showed a preservation of broad tonotopic tuning across sound levels without shifts towards lower frequencies. Synaptic integration within corticocortical circuits may hence contribute to a level-robust representation of auditory information on a neuronal population level in the auditory cortex.

Surface confined assemblies and polymers for sensing and molecular logic

Science.gov (United States)

de Ruiter, Graham; Altman, Marc; Motiei, Leila; Lahav, Michal; van der Boom, Milko E.

2013-05-01

Since the development of molecule-based sensors and the introduction of molecules mimicking the behavior of the AND gate in solution by de Silva in 1993, molecular (Boolean) Logic and Computing (MBLC) has become increasingly popular. The molecular approach toward Boolean logic resulted in intriguing proofs of concepts in solution including logic gates, half-adders, multiplexers, and flip-flop logic circuits. Molecular assemblies can perform diverse logic tasks by reconfiguring their inputs. Our recent research activities focus on MBLC with electrochromic polymers and immobilized polypyridyl complexes on solid support. We have designed a series of coordination-based thin films that are formed linearly by stepwise wet-chemical deposition or by self-propagating molecular assembly. The electrochromic properties of these films can be used for (i) detecting various analytes in solution and in the air, (ii) MBLC, (iii) electron-transfer studies, and (iv) interlayers for efficient inverted bulk-heterojunction solar cells. Our concept toward MBLC with functionalized surfaces is applicable to electrochemical and chemical inputs coupled with optical readout. Using this approach, we demonstrated various logic architectures with redox-active functionalized surfaces. Electrochemically operated sequential logic systems (e.g., flip-flops), multi-valued logic, and multi-state memory have been designed, which can improve computational power without increasing spatial requirements. Applying multi-valued digits in data storage and information processing could exponentially increase memory capacity. Our approach is applicable to highly diverse electrochromic thin films that operate at practical voltages (< 1.5 V).

Comparative evaluation of pressure generated on a simulated maxillary oral analog by impression materials in custom trays of different spacer designs: An in vitro study

Directory of Open Access Journals (Sweden)

Sakshi Chopra

2016-01-01

Full Text Available Introduction: Literature reveals that masticatory load on denture bearing tissues through complete dentures should be maximum on primary stress bearing areas and least on relief area in accordance with the histology of underlying tissues. A study to validate the existing beliefs was planned to compare the pressure on mucosa using selective pressure technique and minimal pressure technique, with the incorporation of two different impression materials utilizing the pressure sensors during secondary impression procedure. Materials and Methods: The study was performed using a maxillary analog. Three pressure sensors were imbedded in the oral analog, one in the mid palatine area and the other two in the right and left ridge crest. Custom trays of two different configurations were fabricated. The two impression materials tested were light body and zinc oxide eugenol. A total of 40 impressions were made. A constant weight of 1 kg was placed, and the pressure was recorded as initial and end pressures. Results: A significant difference in the pressure produced using different impression materials was found (P < 0.001. Light body vinyl polysiloxane produced significantly lesser pressure than zinc oxide eugenol impression materials. The presence of relief did affect the magnitude of pressure at various locations. Conclusion: All impression materials produced pressure during maxillary edentulous impression making. Tray modification is an important factor in changing the amount of pressure produced. The impression materials used also had a significant role to play on the pressures acting on the tissues during impression procedure. Clinical Implication: Light body VPS impression material may be recommended to achieve minimal pressure on the denture bearing tissues in both selective as well as minimal pressure techniques.

A thermal-hydraulic test rig for advanced fast reactor fuel assemblies

International Nuclear Information System (INIS)

Rapier, A.C.

1989-03-01

A new design of fast reactor fuel assemblies has been proposed in which the pins are supported in grids attached to the wrapper by flexible skirts. Coolant mixing is enhanced by the skirts diverting flow into the cluster of pins at each grid. There are insufficient empirical data available for the detailed design of the skirt or for the input to computer calculations of flow and heat transfer. A test rig to provide these data has been designed and built. (author)

Optimizing Transcriptome Assemblies for Eleusine indica Leaf and Seedling by Combining Multiple Assemblies from Three De Novo Assemblers

Directory of Open Access Journals (Sweden)

Shu Chen

2015-03-01

Full Text Available Due to rapid advances in sequencing technology, increasing amounts of genomic and transcriptomic data are available for plant species, presenting enormous challenges for biocomputing analysis. A crucial first step for a successful transcriptomics-based study is the building of a high-quality assembly. Here, we utilized three different de novo assemblers (Trinity, Velvet, and CLC and the EvidentialGene pipeline tr2aacds to assemble two optimized transcript sets for the notorious weed species, . Two RNA sequencing (RNA-seq datasets from leaf and aboveground seedlings were processed using three assemblers, which resulted in 20 assemblies for each dataset. The contig numbers and N50 values of each assembly were compared to study the effect of read number, k-mer size, and in silico normalization on assembly output. The 20 assemblies were then processed through the tr2aacds pipeline to remove redundant transcripts and to select the transcript set with the best coding potential. Each assembly contributed a considerable proportion to the final transcript combination with the exception of the CLC-k14. Thus each assembler and parameter set did assemble better contigs for certain transcripts. The redundancy, total contig number, N50, fully assembled contig number, and transcripts related to target-site herbicide resistance were evaluated for the EvidentialGene and Trinity assemblies. Comparing the EvidentialGene set with the Trinity assembly revealed improved quality and reduced redundancy in both leaf and seedling EvidentialGene sets. The optimized transcriptome references will be useful for studying herbicide resistance in and the evolutionary process in the three allotetraploid offspring.

Total dose induced increase in input offset voltage in JFET input operational amplifiers

International Nuclear Information System (INIS)

Pease, R.L.; Krieg, J.; Gehlhausen, M.; Black, J.

1999-01-01

Four different types of commercial JFET input operational amplifiers were irradiated with ionizing radiation under a variety of test conditions. All experienced significant increases in input offset voltage (Vos). Microprobe measurement of the electrical characteristics of the de-coupled input JFETs demonstrates that the increase in Vos is a result of the mismatch of the degraded JFETs. (authors)

The Impact of Outsourcing on the Japanese and South Korean Labor Markets: International Outsourcing of Intermediate Inputs and Assembly in East Asia

OpenAIRE

Ahn, Sanghoon; Fukao, Kyoji; Ito, Keiko

2009-01-01

Applying a common empirical approach to comparable industry-level data on production, trade, and labor markets for Japan and South Korea, this paper aims to investigate the impacts of outsourcing on different sectors of the labor market focusing on differences in educational attainment. While outsourcing measures used in previous studies only take account of the outsourcing of intermediate inputs, this paper, utilizing the Asian International Input-Output Tables, incorporates the outsourcing ...

Direct current linear measurement sub-assembly data and test methods. Nuclear electronic equipment for control and monitoring panel

International Nuclear Information System (INIS)

1977-12-01

The M.C.H./M.E.N.T.3 document is concerned with sub-assemblies intended for measuring on a linear scale the neutron fluence rate or radiation dose rate when connected with nuclear detectors working in current. The symbols used are described. Some definitions and a bibliography are given. The main characteristics of direct current linear measurement sub-assemblies are then described together with corresponding test methods. This type of instrument indicates on a linear scale the level of a direct current applied to its input. The document reviews linear sub-assemblies for general purpose applications, difference amplifiers for monitoring, and averaging amplifiers. The document is intended for electronics manufacturers, designers, persons participating in acceptance trials and plant operators [fr

Fuel assemblies

International Nuclear Information System (INIS)

Nakatsuka, Masafumi.

1979-01-01

Purpose: To prevent scattering of gaseous fission products released from fuel assemblies stored in an fbr type reactor. Constitution; A cap provided with means capable of storing gas is adapted to amount to the assembly handling head, for example, by way of threading in a storage rack of spent fuel assemblies consisting of a bottom plate, a top plate and an assembly support mechanism. By previously eliminating the gas inside of the assembly and the cap in the storage rack, gaseous fission products upon loading, if released from fuel rods during storage, are stored in the cap and do not scatter in the storage rack. (Horiuchi, T.)

[What is hidden behind the Baking Tray Task? Study of sensibility and specificity in right-hemispheric stroke patients].

Science.gov (United States)

Garcia-Fernandez, Juan; Garcia-Molina, Alberto; Aparicio-Lopez, Celeste; Sanchez-Carrion, Rocío; Ensenat, Antònia; Pena-Casanova, Jordi; Roig-Rovira, Teresa

2015-12-16

Tham and Tegner proposed the Baking Tray Task (BTT) as a fast simple assessment test for detecting spatial negligence. However, very few studies have examined its validity as a diagnostic test. To analyse the diagnostic validity of the BTT by measuring its specificity and sensitivity in a sample of subjects with right hemisphere strokes. Forty-eight patients with right hemisphere vascular lesions were distributed in two groups (negligence group, n = 35; non-negligence group, n = 13) according to the scores obtained in a battery of visuospatial examination tests. The participants' performance on the BTT was compared with that of a healthy control group (n = 12). The results showed a high level of sensitivity of the BTT, but low specificity. The performance on the BTT of eight of the 13 members of the non-negligence group was suggestive of negligence. The BTT has proved to be a sensitive test for the detection of spatial negligence. Yet, based on its low specificity, its use alone as a single diagnostic test is not recommended.

Vibration Monitoring Using Fiber Optic Sensors in a Lead-Bismuth Eutectic Cooled Nuclear Fuel Assembly

Directory of Open Access Journals (Sweden)

Ben De Pauw

2016-04-01

Full Text Available Excessive fuel assembly vibrations in nuclear reactor cores should be avoided in order not to compromise the lifetime of the assembly and in order to prevent the occurrence of safety hazards. This issue is particularly relevant to new reactor designs that use liquid metal coolants, such as, for example, a molten lead-bismuth eutectic. The flow of molten heavy metal around and through the fuel assembly may cause the latter to vibrate and hence suffer degradation as a result of, for example, fretting wear or mechanical fatigue. In this paper, we demonstrate the use of optical fiber sensors to measure the fuel assembly vibration in a lead-bismuth eutectic cooled installation which can be used as input to assess vibration-related safety hazards. We show that the vibration characteristics of the fuel pins in the fuel assembly can be experimentally determined with minimal intrusiveness and with high precision owing to the small dimensions and properties of the sensors. In particular, we were able to record local strain level differences of about 0.2 μϵ allowing us to reliably estimate the vibration amplitudes and modal parameters of the fuel assembly based on optical fiber sensor readings during different stages of the operation of the facility, including the onset of the coolant circulation and steady-state operation.

Durability evaluation of photovoltaic blanket materials exposed on LDEF tray S1003

International Nuclear Information System (INIS)

Rutledge, S.K.; Olle, R.M.

1992-01-01

Several candidate protective coatings on Kapton and uncoated Kapton were exposed to the low Earth orbital (LEO) environment on the Long Duration Exposure Facility (LDEF) to determine if the coatings could be used to protect polymeric substrates from degradation in the LEO environment. The coatings that were evaluated were 700 A of aluminum oxide, 650 A of silicon dioxide, and 650 A of a 4 percent polytetrafluoroethylene-96 percent silicon dioxide mixed coating. All of the coatings evaluated were ion beam sputter deposited. These materials were exposed to a very low atomic oxygen fluence (4.8 x 10 exp 19 atoms/sq. cm) as a result of the experiment tray being located 98 degrees from the ram direction. As a result of the low atomic oxygen fluence, determination of a change in mass was not possible for any of the samples including the uncoated Kapton. There was no evidence of spalling of any of the coatings after the approximately 33,600 thermal cycles recorded for LDEF. The surface of the uncoated Kapton, however, did show evidence of grazing incidence texturing. There was a 7-8 percent increase in solar absorptance for the silicon dioxide and aluminum oxide coated Kapton and only a 4 percent increase for the mixed coating. It appears that the addition of a small amount of fluoropolymer may reduce the magnitude of absorptance increase due to environmental exposure. Thermal emittance did not change significantly for any of the exposed samples. Scanning electron microscopy revealed few micrometeoroid or debris impacts, but the impact sites found indicated that the extent of damage or cracking of the coating around the defect site did not extend beyond a factor of three of the impact crater diameter. This limiting of impact damage is of great significance for the durability of thin film coatings used for protection against the LEO environment

Solid phase radioimmunoassay for plasma testosterone using a plastic microtiter tray

International Nuclear Information System (INIS)

Hosogi, Hidemi

1975-01-01

In order to simplify radioimmunoassay for plasma testosterone and to measure many samples at the same time, a method of solid phase radioimmunoassay utilizing a plastic disposable microtiter tray (DMT) by which chromatography can be omitted was investigated. Other steroids except for 5α-dihydrotestosterone (5α-DHT) had a low degree of cross reactivity with the antiserum. Five α-DHT which could be measured together with testosterone in this assay was not a problem clinically because of its strong androgenic activity. The best standard curve was obtained when the antiserum was diluted to 1:1000. The sensitivity of this assay was 10 pg-tube. The maximal adsorption of antibody to plastic DMT was observed when the pH of the antiserum was within the range of 6.5-9.5 and the precoating time was 24 hr at room temperature. The best pH of the incubation buffer was 0.8, and the antigen-antibody reaction became a plateau when the incubation exceeded 6 hrs. The water blank in this assay was 4.6 +- 2.1 pg/tube. The recovery of testosterone (50, 100, 200 pg) when added to 0.1 ml female plasma was 99 +- 6.8%. Coefficients of variation within assay and between assays were below 11.2% and 20.0%, respectively. Correlation between this method and the dextran-coated charcoal method was fairly good (r=0.938). Plasma testosterone levels in 10 normal males and 12 normal females were 616 +- 202 (mean +- SD) ng/dl and 66 +- 29 (mean +- SD) ng/dl, respectively. The levels were low in patients with hypopituitarism, hypogonadism and acromegaly. They were normal in patients with Cushing's syndrome due to adrenal hyperplasia and adenoma, but they were high in a patient with adrenal carcinoma. In a patient with testicular feminization, the level was 632 ng/dl. This increased after the administration of HCG, and decreased to 127.5 ng/dl after castration. (auth.)

Evaluation of substrate and tray types for beet seedlings/ Avaliação de mudas de beterraba em função do substrato e do tipo de bandeja

Directory of Open Access Journals (Sweden)

Juliana Souza Braga

2007-07-01

Full Text Available The experiment was carried out from April to May of 1998 in Piracicaba- SP, with the objective of evaluating three substrates: Plantimax, Mogimax and Gioplanta, and two recipient trays: one with 128 cells and other with 200 cells, in beet seedling production of cultivar “Early Wonder”. The evaluation was accomplished 40 days after sowing by the following parameters: plant height, root length, total dry mass, root dry mass, shoot dry mass and the shoot/root relation. The experimental design was randomized blocks in 3 x 2 outline factorial with 4 replications. In all evaluated parameters, there were found significant differences among substrates and trays. Also, it was observed significant interaction in total dry mass, shoot dry mass and shoot/root relation. Plantmax and Mogimax were superior for the most of the evaluated parameters. Recipient tray with 128 cells was better than 200 cells, being more indicated for beet seedling production.Visando avaliar o efeito de três substratos, Plantimax, Mogimax, Gioplanta, e bandejas de poliestireno expandido com 128 e 200 células, na produção de mudas de beterraba da cultivar “Early Wonder”, realizou-se um experimento no período de abril a maio de 1998 em Piracicaba- SP. A avaliação foi realizada 40 dias após a semeadura e as variáveis estudas foram altura da planta, comprimento do sistema radicular, massa seca total, massa seca da parte aérea, massa seca de raiz e determinada a razão entre a massa seca da parte aérea e a massa seca das raízes (RPAR. O delineamento experimental utilizado foi de blocos casualizados, em esquema fatorial 3 x 2, com 4 repetições. Em todas as variáveis estudas foi observada diferença significativa para substratos e recipientes. Para massa seca da parte aérea, massa seca total e RPAR foram observadas interações significativas entre tipo de substrato e bandeja. Plantimax e Mogimax mostraram-se superiores para maioria dos parâmetros avaliados. A

Input and execution

International Nuclear Information System (INIS)

Carr, S.; Lane, G.; Rowling, G.

1986-11-01

This document describes the input procedures, input data files and operating instructions for the SYVAC A/C 1.03 computer program. SYVAC A/C 1.03 simulates the groundwater mediated movement of radionuclides from underground facilities for the disposal of low and intermediate level wastes to the accessible environment, and provides an estimate of the subsequent radiological risk to man. (author)

Sensor mount assemblies and sensor assemblies

Science.gov (United States)

Miller, David H [Redondo Beach, CA

2012-04-10

Sensor mount assemblies and sensor assemblies are provided. In an embodiment, by way of example only, a sensor mount assembly includes a busbar, a main body, a backing surface, and a first finger. The busbar has a first end and a second end. The main body is overmolded onto the busbar. The backing surface extends radially outwardly relative to the main body. The first finger extends axially from the backing surface, and the first finger has a first end, a second end, and a tooth. The first end of the first finger is disposed on the backing surface, and the tooth is formed on the second end of the first finger.

PLEXOS Input Data Generator

Energy Technology Data Exchange (ETDEWEB)

2017-02-01

The PLEXOS Input Data Generator (PIDG) is a tool that enables PLEXOS users to better version their data, automate data processing, collaborate in developing inputs, and transfer data between different production cost modeling and other power systems analysis software. PIDG can process data that is in a generalized format from multiple input sources, including CSV files, PostgreSQL databases, and PSS/E .raw files and write it to an Excel file that can be imported into PLEXOS with only limited manual intervention.

Evaluation and Validation of Assembling Corrected PacBio Long Reads for Microbial Genome Completion via Hybrid Approaches.

Science.gov (United States)

Lin, Hsin-Hung; Liao, Yu-Chieh

2015-01-01

Despite the ever-increasing output of next-generation sequencing data along with developing assemblers, dozens to hundreds of gaps still exist in de novo microbial assemblies due to uneven coverage and large genomic repeats. Third-generation single-molecule, real-time (SMRT) sequencing technology avoids amplification artifacts and generates kilobase-long reads with the potential to complete microbial genome assembly. However, due to the low accuracy (~85%) of third-generation sequences, a considerable amount of long reads (>50X) are required for self-correction and for subsequent de novo assembly. Recently-developed hybrid approaches, using next-generation sequencing data and as few as 5X long reads, have been proposed to improve the completeness of microbial assembly. In this study we have evaluated the contemporary hybrid approaches and demonstrated that assembling corrected long reads (by runCA) produced the best assembly compared to long-read scaffolding (e.g., AHA, Cerulean and SSPACE-LongRead) and gap-filling (SPAdes). For generating corrected long reads, we further examined long-read correction tools, such as ECTools, LSC, LoRDEC, PBcR pipeline and proovread. We have demonstrated that three microbial genomes including Escherichia coli K12 MG1655, Meiothermus ruber DSM1279 and Pdeobacter heparinus DSM2366 were successfully hybrid assembled by runCA into near-perfect assemblies using ECTools-corrected long reads. In addition, we developed a tool, Patch, which implements corrected long reads and pre-assembled contigs as inputs, to enhance microbial genome assemblies. With the additional 20X long reads, short reads of S. cerevisiae W303 were hybrid assembled into 115 contigs using the verified strategy, ECTools + runCA. Patch was subsequently applied to upgrade the assembly to a 35-contig draft genome. Our evaluation of the hybrid approaches shows that assembling the ECTools-corrected long reads via runCA generates near complete microbial genomes, suggesting

A biomimetic colorimetric logic gate system based on multi-functional peptide-mediated gold nanoparticle assembly.

Science.gov (United States)

Li, Yong; Li, Wang; He, Kai-Yu; Li, Pei; Huang, Yan; Nie, Zhou; Yao, Shou-Zhuo

2016-04-28

In natural biological systems, proteins exploit various functional peptide motifs to exert target response and activity switch, providing a functional and logic basis for complex cellular activities. Building biomimetic peptide-based bio-logic systems is highly intriguing but remains relatively unexplored due to limited logic recognition elements and complex signal outputs. In this proof-of-principle work, we attempted to address these problems by utilizing multi-functional peptide probes and the peptide-mediated nanoparticle assembly system. Here, the rationally designed peptide probes function as the dual-target responsive element specifically responsive to metal ions and enzymes as well as the mediator regulating the assembly of gold nanoparticles (AuNPs). Taking advantage of Zn2+ ions and chymotrypsin as the model inputs of metal ions and enzymes, respectively, we constructed the peptide logic system computed by the multi-functional peptide probes and outputted by the readable colour change of AuNPs. In this way, the representative binary basic logic gates (AND, OR, INHIBIT, NAND, IMPLICATION) have been achieved by delicately coding the peptide sequence, demonstrating the versatility of our logic system. Additionally, we demonstrated that the three-input combinational logic gate (INHIBIT-OR) could also be successfully integrated and applied as a multi-tasking biosensor for colorimetric detection of dual targets. This nanoparticle-based peptide logic system presents a valid strategy to illustrate peptide information processing and provides a practical platform for executing peptide computing or peptide-related multiplexing sensing, implying that the controllable nanomaterial assembly is a promising and potent methodology for the advancement of biomimetic bio-logic computation.

Scoring-and-unfolding trimmed tree assembler: concepts, constructs and comparisons.

Science.gov (United States)

Narzisi, Giuseppe; Mishra, Bud

2011-01-15

Mired by its connection to a well-known -complete combinatorial optimization problem-namely, the Shortest Common Superstring Problem (SCSP)-historically, the whole-genome sequence assembly (WGSA) problem has been assumed to be amenable only to greedy and heuristic methods. By placing efficiency as their first priority, these methods opted to rely only on local searches, and are thus inherently approximate, ambiguous or error prone, especially, for genomes with complex structures. Furthermore, since choice of the best heuristics depended critically on the properties of (e.g. errors in) the input data and the available long range information, these approaches hindered designing an error free WGSA pipeline. We dispense with the idea of limiting the solutions to just the approximated ones, and instead favor an approach that could potentially lead to an exhaustive (exponential-time) search of all possible layouts. Its computational complexity thus must be tamed through a constrained search (Branch-and-Bound) and quick identification and pruning of implausible overlays. For his purpose, such a method necessarily relies on a set of score functions (oracles) that can combine different structural properties (e.g. transitivity, coverage, physical maps, etc.). We give a detailed description of this novel assembly framework, referred to as Scoring-and-Unfolding Trimmed Tree Assembler (SUTTA), and present experimental results on several bacterial genomes using next-generation sequencing technology data. We also report experimental evidence that the assembly quality strongly depends on the choice of the minimum overlap parameter k. SUTTA's binaries are freely available to non-profit institutions for research and educational purposes at http://www.bioinformatics.nyu.edu.

Support for solar energy collectors

Science.gov (United States)

Cole, Corey; Ardell-Smith, Zachary; Ciasulli, John; Jensen, Soren

2016-11-01

A solar energy collection system can include support devices configured to accommodate misalignment of components during assembly. For example, the system can include piles fixed to the earth and an adjustable bearing assembly at the upper end of the pile. The adjustable bearing assembly can include at least one of a vertical adjustment device, a lateral adjustment device and an angular adjustment device. The solar energy collection system can also include a plurality of solar energy collection device pre-wired together and mounted to a support member so as to form modular units. The system can also include enhanced supports for wire trays extending between rows of solar energy collection devices.

SSYST-3. Input description

International Nuclear Information System (INIS)

Meyder, R.

1983-12-01

The code system SSYST-3 is designed to analyse the thermal and mechanical behaviour of a fuel rod during a LOCA. The report contains a complete input-list for all modules and several tested inputs for a LOCA analysis. (orig.)

Material input of nuclear fuel

International Nuclear Information System (INIS)

Rissanen, S.; Tarjanne, R.

2001-01-01

The Material Input (MI) of nuclear fuel, expressed in terms of the total amount of natural material needed for manufacturing a product, is examined. The suitability of the MI method for assessing the environmental impacts of fuels is also discussed. Material input is expressed as a Material Input Coefficient (MIC), equalling to the total mass of natural material divided by the mass of the completed product. The material input coefficient is, however, only an intermediate result, which should not be used as such for the comparison of different fuels, because the energy contents of nuclear fuel is about 100 000-fold compared to the energy contents of fossil fuels. As a final result, the material input is expressed in proportion to the amount of generated electricity, which is called MIPS (Material Input Per Service unit). Material input is a simplified and commensurable indicator for the use of natural material, but because it does not take into account the harmfulness of materials or the way how the residual material is processed, it does not alone express the amount of environmental impacts. The examination of the mere amount does not differentiate between for example coal, natural gas or waste rock containing usually just sand. Natural gas is, however, substantially more harmful for the ecosystem than sand. Therefore, other methods should also be used to consider the environmental load of a product. The material input coefficient of nuclear fuel is calculated using data from different types of mines. The calculations are made among other things by using the data of an open pit mine (Key Lake, Canada), an underground mine (McArthur River, Canada) and a by-product mine (Olympic Dam, Australia). Furthermore, the coefficient is calculated for nuclear fuel corresponding to the nuclear fuel supply of Teollisuuden Voima (TVO) company in 2001. Because there is some uncertainty in the initial data, the inaccuracy of the final results can be even 20-50 per cent. The value

Chemical sensors are hybrid-input memristors

Science.gov (United States)

Sysoev, V. I.; Arkhipov, V. E.; Okotrub, A. V.; Pershin, Y. V.

2018-04-01

Memristors are two-terminal electronic devices whose resistance depends on the history of input signal (voltage or current). Here we demonstrate that the chemical gas sensors can be considered as memristors with a generalized (hybrid) input, namely, with the input consisting of the voltage, analyte concentrations and applied temperature. The concept of hybrid-input memristors is demonstrated experimentally using a single-walled carbon nanotubes chemical sensor. It is shown that with respect to the hybrid input, the sensor exhibits some features common with memristors such as the hysteretic input-output characteristics. This different perspective on chemical gas sensors may open new possibilities for smart sensor applications.

Mobius Assembly: A versatile Golden-Gate framework towards universal DNA assembly.

Directory of Open Access Journals (Sweden)

Andreas I Andreou

Full Text Available Synthetic biology builds upon the foundation of engineering principles, prompting innovation and improvement in biotechnology via a design-build-test-learn cycle. A community-wide standard in DNA assembly would enable bio-molecular engineering at the levels of predictivity and universality in design and construction that are comparable to other engineering fields. Golden Gate Assembly technology, with its robust capability to unidirectionally assemble numerous DNA fragments in a one-tube reaction, has the potential to deliver a universal standard framework for DNA assembly. While current Golden Gate Assembly frameworks (e.g. MoClo and Golden Braid render either high cloning capacity or vector toolkit simplicity, the technology can be made more versatile-simple, streamlined, and cost/labor-efficient, without compromising capacity. Here we report the development of a new Golden Gate Assembly framework named Mobius Assembly, which combines vector toolkit simplicity with high cloning capacity. It is based on a two-level, hierarchical approach and utilizes a low-frequency cutter to reduce domestication requirements. Mobius Assembly embraces the standard overhang designs designated by MoClo, Golden Braid, and Phytobricks and is largely compatible with already available Golden Gate part libraries. In addition, dropout cassettes encoding chromogenic proteins were implemented for cost-free visible cloning screening that color-code different cloning levels. As proofs of concept, we have successfully assembled up to 16 transcriptional units of various pigmentation genes in both operon and multigene arrangements. Taken together, Mobius Assembly delivers enhanced versatility and efficiency in DNA assembly, facilitating improved standardization and automation.

Tunable smart digital structure (SDS) to modularly assemble soft actuators with layered adhesive bonding

Science.gov (United States)

Jin, Hu; Dong, Erbao; Xu, Min; Xia, Qirong; Liu, Shuai; Li, Weihua; Yang, Jie

2018-01-01

Many shape memory alloy (SMA)-based soft actuators have specific composite structures and manufacture processes, and are therefore unique. However, these exclusive characteristics limit their capabilities and applications, so in this article a soft and smart digital structure (SDS) is proposed that acts like a modular unit to assemble soft actuators by a layered adhesive bonding process. The SDS is a fully soft structure that encapsulates a digital skeleton consisting of four groups of parallel and independently actuated SMA wires capable of outputting a four-channel tunable force. The layered adhesive bonding process modularly bonds several SDSs with an elastic backbone to fabricate a layered soft actuator where the elastic backbone is used to recover the SDSs in a cooling process using the SMA wires. Two kinds of SDS-based soft actuators were modularly assembled, an actuator, SDS-I, with a two-dimensional reciprocal motion, and an actuator, SDS-II, capable of bi-directional reciprocal motion. The thermodynamics and phase transformation modeling of the SDS-based actuator were analyzed. Several extensional soft actuators were also assembled by bonding the SDS with an anomalous elastic backbone or modularly assembling the SDS-Is and SDS-IIs. These modularly assembled soft actuators delivered more output channels and a complicated motion, e.g., an actinomorphic soft actuator with four SDS-Is jumps in a series of hierarchical heights and directional movement by tuning the input channels of the SDSs. This result showed that the SDS can modularly assemble multifarious soft actuators with diverse capabilities, steerability and tunable outputs.

Programmed Nanomaterial Assemblies in Large Scales: Applications of Synthetic and Genetically- Engineered Peptides to Bridge Nano-Assemblies and Macro-Assemblies

Energy Technology Data Exchange (ETDEWEB)

Matsui, Hiroshi

2014-09-09

Work is reported in these areas: Large-scale & reconfigurable 3D structures of precise nanoparticle assemblies in self-assembled collagen peptide grids; Binary QD-Au NP 3D superlattices assembled with collagen-like peptides and energy transfer between QD and Au NP in 3D peptide frameworks; Catalytic peptides discovered by new hydrogel-based combinatorial phage display approach and their enzyme-mimicking 2D assembly; New autonomous motors of metal-organic frameworks (MOFs) powered by reorganization of self-assembled peptides at interfaces; Biomimetic assembly of proteins into microcapsules on oil-in-water droplets with structural reinforcement via biomolecular recognition-based cross-linking of surface peptides; and Biomimetic fabrication of strong freestanding genetically-engineered collagen peptide films reinforced by quantum dot joints. We gained the broad knowledge about biomimetic material assembly from nanoscale to microscale ranges by coassembling peptides and NPs via biomolecular recognition. We discovered: Genetically-engineered collagen-like peptides can be self-assembled with Au NPs to generate 3D superlattices in large volumes (> μm{sup 3}); The assembly of the 3D peptide-Au NP superstructures is dynamic and the interparticle distance changes with assembly time as the reconfiguration of structure is triggered by pH change; QDs/NPs can be assembled with the peptide frameworks to generate 3D superlattices and these QDs/NPs can be electronically coupled for the efficient energy transfer; The controlled assembly of catalytic peptides mimicking the catalytic pocket of enzymes can catalyze chemical reactions with high selectivity; and, For the bacteria-mimicking swimmer fabrication, peptide-MOF superlattices can power translational and propellant motions by the reconfiguration of peptide assembly at the MOF-liquid interface.

Enhanced Input in LCTL Pedagogy

Directory of Open Access Journals (Sweden)

Marilyn S. Manley

2009-08-01

Full Text Available Language materials for the more-commonly-taught languages (MCTLs often include visual input enhancement (Sharwood Smith 1991, 1993 which makes use of typographical cues like bolding and underlining to enhance the saliency of targeted forms. For a variety of reasons, this paper argues that the use of enhanced input, both visual and oral, is especially important as a tool for the lesscommonly-taught languages (LCTLs. As there continues to be a scarcity of teaching resources for the LCTLs, individual teachers must take it upon themselves to incorporate enhanced input into their own self-made materials. Specific examples of how to incorporate both visual and oral enhanced input into language teaching are drawn from the author’s own experiences teaching Cuzco Quechua. Additionally, survey results are presented from the author’s Fall 2010 semester Cuzco Quechua language students, supporting the use of both visual and oral enhanced input.

Enhanced Input in LCTL Pedagogy

Directory of Open Access Journals (Sweden)

Marilyn S. Manley

2010-08-01

Full Text Available Language materials for the more-commonly-taught languages (MCTLs often include visual input enhancement (Sharwood Smith 1991, 1993 which makes use of typographical cues like bolding and underlining to enhance the saliency of targeted forms. For a variety of reasons, this paper argues that the use of enhanced input, both visual and oral, is especially important as a tool for the lesscommonly-taught languages (LCTLs. As there continues to be a scarcity of teaching resources for the LCTLs, individual teachers must take it upon themselves to incorporate enhanced input into their own self-made materials. Specific examples of how to incorporate both visual and oral enhanced input into language teaching are drawn from the author’s own experiences teaching Cuzco Quechua. Additionally, survey results are presented from the author’s Fall 2010 semester Cuzco Quechua language students, supporting the use of both visual and oral enhanced input.

Self-assembly of self-assembled molecular triangles

Indian Academy of Sciences (India)

While the solution state structure of 1 can be best described as a trinuclear complex, in the solidstate well-fashioned intermolecular - and CH- interactions are observed. Thus, in the solid-state further self-assembly of already self-assembled molecular triangle is witnessed. The triangular panels are arranged in a linear ...

A Novel Reconfigurable Logic Unit Based on the DNA-Templated Potassium-Concentration-Dependent Supramolecular Assembly.

Science.gov (United States)

Yang, Chunrong; Zou, Dan; Chen, Jianchi; Zhang, Linyan; Miao, Jiarong; Huang, Dan; Du, Yuanyuan; Yang, Shu; Yang, Qianfan; Tang, Yalin

2018-03-15

Plenty of molecular circuits with specific functions have been developed; however, logic units with reconfigurability, which could simplify the circuits and speed up the information process, are rarely reported. In this work, we designed a novel reconfigurable logic unit based on a DNA-templated, potassium-concentration-dependent, supramolecular assembly, which could respond to the input stimuli of H + and K + . By inputting different concentrations of K + , the logic unit could implement three significant functions, including a half adder, a half subtractor, and a 2-to-4 decoder. Considering its reconfigurable ability and good performance, the novel prototypes developed here may serve as a promising proof of principle in molecular computers. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evaluation of nine popular de novo assemblers in microbial genome assembly.

Science.gov (United States)

Forouzan, Esmaeil; Maleki, Masoumeh Sadat Mousavi; Karkhane, Ali Asghar; Yakhchali, Bagher

2017-12-01

Next generation sequencing (NGS) technologies are revolutionizing biology, with Illumina being the most popular NGS platform. Short read assembly is a critical part of most genome studies using NGS. Hence, in this study, the performance of nine well-known assemblers was evaluated in the assembly of seven different microbial genomes. Effect of different read coverage and k-mer parameters on the quality of the assembly were also evaluated on both simulated and actual read datasets. Our results show that the performance of assemblers on real and simulated datasets could be significantly different, mainly because of coverage bias. According to outputs on actual read datasets, for all studied read coverages (of 7×, 25× and 100×), SPAdes and IDBA-UD clearly outperformed other assemblers based on NGA50 and accuracy metrics. Velvet is the most conservative assembler with the lowest NGA50 and error rate. Copyright © 2017. Published by Elsevier B.V.

Comparison of hydrogen generation for TVSM and TVSA fuel assemblies for water water energy reactor (VVER)-1000

International Nuclear Information System (INIS)

Stefanova, A.E.; Groudev, P.P.; Atanasova, B.P.

2009-01-01

This paper presents the results received during investigation of hydrogen generation for both types fuel assemblies-the old modernistic type of fuel assemblies (TVSM) and recently installed new one alternative type of fuel assemblies (TVSA) in case of severe accident. There are some differences between both types FAs. They have different geometry as well as different burnable poisons. To investigate behavior of new fuel assemblies during the severe conditions it have been performed comparison of fuel behavior of old type TVSM fuel assembly to new one TVSA. To perform this investigation it has been used MELCOR 'input model' for Kozloduy Nuclear Power Plant (KNPP) VVER 1000. The model was developed by Institute for Nuclear Research and Nuclear Energy-Bulgarian Academy of Sciences (INRNE-BAS) for investigation of severe accident scenarios and Probabilistic Safety Analyses (PSA) level 2. The model provides a significant analytical capability for the Bulgarian technical specialists, working in the field of the NPP safety, for analysis of core and containment damaged states and the estimation of radionuclides release outside fuel cladding. It was accepted criteria for vessel integrity about hydrogen concentration to be 8%. This criterion was based on the decision of RSK (Germany commission for reactor safety). Generally based on the received results it was made conclusion that using both types of fuel assemblies it was not disturbance safety conditions of NPP

A conceptual design of assembly strategy and dedicated tools for assembly of 40o sector

International Nuclear Information System (INIS)

Park, H.K.; Nam, K.O.; Kim, D.J.; Ahn, H.J.; Lee, J.H.; Im, K.; Shaw, R.

2010-01-01

The International Thermanuclear Experimental Reactor (ITER) tokamak device is composed of 9 vacuum vessel (VV)/toroidal field coils (TFCs)/vacuum vessel thermal shields (VVTS) 40 o sectors. Each VV/TFCs/VVTS 40 o sector is made up of one 40 o VV, two 20 o TFCs and associated VVTS segments. The 40 o sectors are sub-assembled at assembly hall respectively and then nine 40 o sectors sub-assembled at assembly hall are finally assembled at tokamak in-pit hall. The assembly strategy and tools for the 40 o sector sub-assembly and final assembly should be developed to satisfy the basic assembly requirements of the ITER tokamak device. Accordingly, the purpose-built assembly tools should be designed and manufactured considering assembly plan, available space, cost, safety, easy operation, efficient maintenance, and so on. The 40 o sector assembly tools are classified into 2 groups. One group is the sub-assembly tools including upending tool, lifting tool, sub-assembly tool, VV supports and bracing tools used at assembly hall and the other group is the in-pit assembly tools including lifting tool, central column, radial beams and their supports. This paper describes the current status of the assembly strategy and major tools for the VV/TFCs/VVTS 40 o sector assembly at in-pit hall and assembly hall. The conceptual design of the major assembly tools and assembly process at assembly hall and tokamak in-pit hall are presented also.

Three-Dimensional Numerical Evaluation of Thermal Performance of Uninsulated Wall Assemblies: Preprint

Energy Technology Data Exchange (ETDEWEB)

Ridouane, E. H.; Bianchi, M.

2011-11-01

This study describes a detailed three-dimensional computational fluid dynamics modeling to evaluate the thermal performance of uninsulated wall assemblies accounting for conduction through framing, convection, and radiation. The model allows for material properties variations with temperature. Parameters that were varied in the study include ambient outdoor temperature and cavity surface emissivity. Understanding the thermal performance of uninsulated wall cavities is essential for accurate prediction of energy use in residential buildings. The results can serve as input for building energy simulation tools for modeling the temperature dependent energy performance of homes with uninsulated walls.

Development of an Input Model to MELCOR 1.8.5 for the Oskarshamn 3 BWR

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Lars [Lentek, Nykoeping (Sweden)

2006-05-15

An input model has been prepared to the code MELCOR 1.8.5 for the Swedish Oskarshamn 3 Boiling Water Reactor (O3). This report describes the modelling work and the various files which comprise the input deck. Input data are mainly based on original drawings and system descriptions made available by courtesy of OKG AB. Comparison and check of some primary system data were made against an O3 input file to the SCDAP/RELAP5 code that was used in the SARA project. Useful information was also obtained from the FSAR (Final Safety Analysis Report) for O3 and the SKI report '2003 Stoerningshandboken BWR'. The input models the O3 reactor at its current state with the operating power of 3300 MW{sub th}. One aim with this work is that the MELCOR input could also be used for power upgrading studies. All fuel assemblies are thus assumed to consist of the new Westinghouse-Atom's SVEA-96 Optima2 fuel. MELCOR is a severe accident code developed by Sandia National Laboratory under contract from the U.S. Nuclear Regulatory Commission (NRC). MELCOR is a successor to STCP (Source Term Code Package) and has thus a long evolutionary history. The input described here is adapted to the latest version 1.8.5 available when the work began. It was released the year 2000, but a new version 1.8.6 was distributed recently. Conversion to the new version is recommended. (During the writing of this report still another code version, MELCOR 2.0, has been announced to be released within short.) In version 1.8.5 there is an option to describe the accident progression in the lower plenum and the melt-through of the reactor vessel bottom in more detail by use of the Bottom Head (BH) package developed by Oak Ridge National Laboratory especially for BWRs. This is in addition to the ordinary MELCOR COR package. Since problems arose running with the BH input two versions of the O3 input deck were produced, a NONBH and a BH deck. The BH package is no longer a separate package in the new 1

Fuel injection assembly for use in turbine engines and method of assembling same

Science.gov (United States)

Berry, Jonathan Dwight; Johnson, Thomas Edward; York, William David; Uhm, Jong Ho

2015-12-15

A fuel injection assembly for use in a turbine engine is provided. The fuel injection assembly includes an end cover, an endcap assembly, a fluid supply chamber, and a plurality of tube assemblies positioned at the endcap assembly. Each of the tube assemblies includes housing having a fuel plenum and a cooling fluid plenum. The cooling fluid plenum is positioned downstream from the fuel plenum and separated from the fuel plenum by an intermediate wall. The plurality of tube assemblies also include a plurality of tubes that extends through the housing. Each of the plurality of tubes is coupled in flow communication with the fluid supply chamber and a combustion chamber positioned downstream from the tube assembly. The plurality of tube assemblies further includes an aft plate at a downstream end of the cooling fluid plenum. The plate includes at least one aperture.

AutoAssemblyD: a graphical user interface system for several genome assemblers.

Science.gov (United States)

Veras, Adonney Allan de Oliveira; de Sá, Pablo Henrique Caracciolo Gomes; Azevedo, Vasco; Silva, Artur; Ramos, Rommel Thiago Jucá

2013-01-01

Next-generation sequencing technologies have increased the amount of biological data generated. Thus, bioinformatics has become important because new methods and algorithms are necessary to manipulate and process such data. However, certain challenges have emerged, such as genome assembly using short reads and high-throughput platforms. In this context, several algorithms have been developed, such as Velvet, Abyss, Euler-SR, Mira, Edna, Maq, SHRiMP, Newbler, ALLPATHS, Bowtie and BWA. However, most such assemblers do not have a graphical interface, which makes their use difficult for users without computing experience given the complexity of the assembler syntax. Thus, to make the operation of such assemblers accessible to users without a computing background, we developed AutoAssemblyD, which is a graphical tool for genome assembly submission and remote management by multiple assemblers through XML templates. AssemblyD is freely available at https://sourceforge.net/projects/autoassemblyd. It requires Sun jdk 6 or higher.

Diagnostic procedure on brake pad assembly based on Young's modulus estimation

International Nuclear Information System (INIS)

Chiariotti, P; Santolini, C; Tomasini, E P; Martarelli, M

2013-01-01

Quality control of brake pads is an important issue, since the pad is a key component of the braking system. Typical damage of a brake pad assembly is the pad–backing plate detachment that affects and modifies the mechanical properties of the whole system. The most sensitive parameter to the damage is the effective Young's modulus, since the damage induces a decrease of the pad assembly stiffness and therefore of its effective Young's modulus: indeed its variation could be used for diagnostic purposes. The effective Young's modulus can be estimated from the first bending resonance frequency identified from the frequency response function measured on the pad assembly. Two kinds of excitation methods, i.e. conventional impulse excitation and magnetic actuation, will be presented and two different measurement sensors, e.g. laser Doppler vibrometer and microphone, analyzed. The robustness of the effective Young's modulus as a diagnostic feature will be demonstrated in comparison to the first bending resonance frequency, which is more sensitive to geometrical dimensions. Variability in the sample dimension, in fact, will induce a variation of the resonance frequency which could be mistaken for damage. The diagnostic approach has been applied to a set of undamaged and damaged pad assemblies showing good performance in terms of damage identification. The environmental temperature can be an important interfering input for the diagnostic procedure, since it influences the effective Young's modulus of the assembly. For that reason, a test at different temperatures in the range between 15 °C and 30 °C has been performed, evidencing that damage identification technique is efficient at any temperature. The robustness of the Young's modulus as a diagnostic feature with respect to damping is also presented. (paper)

MDS MIC Catalog Inputs

Science.gov (United States)

Johnson-Throop, Kathy A.; Vowell, C. W.; Smith, Byron; Darcy, Jeannette

2006-01-01

This viewgraph presentation reviews the inputs to the MDS Medical Information Communique (MIC) catalog. The purpose of the group is to provide input for updating the MDS MIC Catalog and to request that MMOP assign Action Item to other working groups and FSs to support the MITWG Process for developing MIC-DDs.

Assembly, alignment and test of the Transiting Exoplanet Survey Satellite (TESS) optical assemblies

Science.gov (United States)

Balonek, Gregory; Brown, Joshua J.; Andre, James E.; Chesbrough, Christian D.; Chrisp, Michael P.; Dalpiaz, Michael; Lennon, Joseph; Richards, B. C.; Clark, Kristin E.

2017-08-01

The Transiting Exoplanet Survey Satellite (TESS) will carry four visible waveband, seven-element, refractive F/1.4 lenses, each with a 34 degree diagonal field of view. This paper describes the methods used for the assembly, alignment and test of the four flight optical assemblies. Prior to commencing the build of the four flight optical assemblies, a Risk Reduction Unit (RRU) was successfully assembled and tested [1]. The lessons learned from the RRU were applied to the build of the flight assemblies. The main modifications to the flight assemblies include the inking of the third lens element stray light mitigation, tighter alignment tolerances, and diamond turning for critical mechanical surfaces. Each of the optical assemblies was tested interferometrically and measured with a low coherence distance measuring interferometer (DMI) to predict the optimal shim thickness between the lens assembly and detector before -75°C environmental testing. In addition to individual test data, environmental test results from prior assemblies allow for the exploration of marginal performance differences between each of the optical assemblies.

SWAP-Assembler: scalable and efficient genome assembly towards thousands of cores.

Science.gov (United States)

Meng, Jintao; Wang, Bingqiang; Wei, Yanjie; Feng, Shengzhong; Balaji, Pavan

2014-01-01

There is a widening gap between the throughput of massive parallel sequencing machines and the ability to analyze these sequencing data. Traditional assembly methods requiring long execution time and large amount of memory on a single workstation limit their use on these massive data. This paper presents a highly scalable assembler named as SWAP-Assembler for processing massive sequencing data using thousands of cores, where SWAP is an acronym for Small World Asynchronous Parallel model. In the paper, a mathematical description of multi-step bi-directed graph (MSG) is provided to resolve the computational interdependence on merging edges, and a highly scalable computational framework for SWAP is developed to automatically preform the parallel computation of all operations. Graph cleaning and contig extension are also included for generating contigs with high quality. Experimental results show that SWAP-Assembler scales up to 2048 cores on Yanhuang dataset using only 26 minutes, which is better than several other parallel assemblers, such as ABySS, Ray, and PASHA. Results also show that SWAP-Assembler can generate high quality contigs with good N50 size and low error rate, especially it generated the longest N50 contig sizes for Fish and Yanhuang datasets. In this paper, we presented a highly scalable and efficient genome assembly software, SWAP-Assembler. Compared with several other assemblers, it showed very good performance in terms of scalability and contig quality. This software is available at: https://sourceforge.net/projects/swapassembler.

An approach for coupled-code multiphysics core simulations from a common input

International Nuclear Information System (INIS)

Schmidt, Rodney; Belcourt, Kenneth; Hooper, Russell; Pawlowski, Roger; Clarno, Kevin; Simunovic, Srdjan; Slattery, Stuart; Turner, John; Palmtag, Scott

2015-01-01

Highlights: • We describe an approach for coupled-code multiphysics reactor core simulations. • The approach can enable tight coupling of distinct physics codes with a common input. • Multi-code multiphysics coupling and parallel data transfer issues are explained. • The common input approach and how the information is processed is described. • Capabilities are demonstrated on an eigenvalue and power distribution calculation. - Abstract: This paper describes an approach for coupled-code multiphysics reactor core simulations that is being developed by the Virtual Environment for Reactor Applications (VERA) project in the Consortium for Advanced Simulation of Light-Water Reactors (CASL). In this approach a user creates a single problem description, called the “VERAIn” common input file, to define and setup the desired coupled-code reactor core simulation. A preprocessing step accepts the VERAIn file and generates a set of fully consistent input files for the different physics codes being coupled. The problem is then solved using a single-executable coupled-code simulation tool applicable to the problem, which is built using VERA infrastructure software tools and the set of physics codes required for the problem of interest. The approach is demonstrated by performing an eigenvalue and power distribution calculation of a typical three-dimensional 17 × 17 assembly with thermal–hydraulic and fuel temperature feedback. All neutronics aspects of the problem (cross-section calculation, neutron transport, power release) are solved using the Insilico code suite and are fully coupled to a thermal–hydraulic analysis calculated by the Cobra-TF (CTF) code. The single-executable coupled-code (Insilico-CTF) simulation tool is created using several VERA tools, including LIME (Lightweight Integrating Multiphysics Environment for coupling codes), DTK (Data Transfer Kit), Trilinos, and TriBITS. Parallel calculations are performed on the Titan supercomputer at Oak

Assembly tool design

International Nuclear Information System (INIS)

Kanamori, Naokazu; Nakahira, Masataka; Ohkawa, Yoshinao; Tada, Eisuke; Seki, Masahiro

1996-06-01

The reactor core of the International Thermonuclear Experimental Reactor (ITER) is assembled with a number of large and asymmetric components within a tight tolerance in order to assure the structural integrity for various loads and to provide the tritium confinement. In addition, the assembly procedure should be compatible with remote operation since the core structures will be activated by 14-MeV neutrons once it starts operation and thus personal access will be prohibited. Accordingly, the assembly procedure and tool design are quite essential and should be designed from the beginning to facilitate remote operation. According to the ITER Design Task Agreement, the Japan Atomic Energy Research Institute (JAERI) has performed design study to develop the assembly procedures and associated tool design for the ITER tokamak assembly. This report describes outlines of the assembly tools and the remaining issues obtained in this design study. (author)

Drive piston assembly for a valve actuator assembly

Science.gov (United States)

Sun, Zongxuan

2010-02-23

A drive piston assembly is provided that is operable to selectively open a poppet valve. The drive piston assembly includes a cartridge defining a generally stepped bore. A drive piston is movable within the generally stepped bore and a boost sleeve is coaxially disposed with respect to the drive piston. A main fluid chamber is at least partially defined by the generally stepped bore, drive piston, and boost sleeve. First and second feedback chambers are at least partially defined by the drive piston and each are disposed at opposite ends of the drive piston. At least one of the drive piston and the boost sleeve is sufficiently configured to move within the generally stepped bore in response to fluid pressure within the main fluid chamber to selectively open the poppet valve. A valve actuator assembly and engine are also provided incorporating the disclosed drive piston assembly.

Cinética e modelagem da secagem de carambola (Averrhoa carambola L. em secador de bandeja = Kinetics and modeling of star fruit (Averrhoa carambola L. drying in a tray dryer

Directory of Open Access Journals (Sweden)

Paulo Bonomo

2010-07-01

Full Text Available No presente trabalho, objetivou-se obter curvas de secagem de carambola (Averrhoa carambola L. em secador de bandejas. A partir dessas curvas foram obtidos dados de taxa de secagem e de difusividade, além do ajuste de modelos semiteóricos aos dados experimentais. As curvas de secagem foram obtidas, utilizando-se um secador de bandejas nas temperaturas de 50, 60 e 70°C e com fluxo de ar de 1,5 m s-1. Aos dados experimentais foram ajustados os modelos dePage, Henderson e Pabis e Exponencial, utilizando-se regressão não-linear. Todos os ajustes tiveram coeficiente de determinação (R2 superior a 0,96, mas o modelo de Page foi o que apresentou melhor ajuste. Observou-se que a difusividade efetiva, calculada a partir da lei de Fick, aumentou com a elevação da temperatura.In this work, drying curves were obtained for the star fruit (Averrhoa carambola L. in a tray dryer. From theses curves, drying rates and diffusivity data were also obtained and semitheoreticalmodels were adjusted. The drying curves were obtained using a tray dryer with temperatures of 50, 60 and 70°C and an air flux of 1.5 m s-1. The Page, Henderson & Pabis and Exponential models were fitted to the experimental data by non-linear regression. All fitted models presented high determination coefficients (R2. The Page model showed the best fit. It was observed that effective diffusivity, calculated by Fick’s law, increased with temperature.

Enhanced Piezoelectricity in a Robust and Harmonious Multilayer Assembly of Electrospun Nanofiber Mats and Microbead-Based Electrodes.

Science.gov (United States)

Kim, Young Won; Lee, Han Bit; Yeon, Si Mo; Park, Jeanho; Lee, Hye Jin; Yoon, Jonghun; Park, Suk Hee

2018-02-14

Here, we present a simple yet highly efficient method to enhance the output performance of a piezoelectric device containing electrospun nanofiber mats. Multiple nanofiber mats were assembled together to harness larger piezoelectric sources in the as-spun fibers, thereby providing enhanced voltage and current outputs compared to those of a single-mat device. In addition to the multilayer assembly, microbead-based electrodes were integrated with the nanofiber mats to deliver a complexed compression and tension force excitation to the piezoelectric layers. A vacuum-packing process was performed to attain a tight and well-organized assembly of the device components even though the total thickness was several millimeters. The integrated piezoelectric device exhibited a maximum voltage and current of 10.4 V and 2.3 μA, respectively. Furthermore, the robust integrity of the device components could provide high-precision sensitivity to perceive small pressures down to approximately 100 Pa while retaining a linear input-output relationship.

Input filter compensation for switching regulators

Science.gov (United States)

Lee, F. C.; Kelkar, S. S.

1982-01-01

The problems caused by the interaction between the input filter, output filter, and the control loop are discussed. The input filter design is made more complicated because of the need to avoid performance degradation and also stay within the weight and loss limitations. Conventional input filter design techniques are then dicussed. The concept of pole zero cancellation is reviewed; this concept is the basis for an approach to control the peaking of the output impedance of the input filter and thus mitigate some of the problems caused by the input filter. The proposed approach for control of the peaking of the output impedance of the input filter is to use a feedforward loop working in conjunction with feedback loops, thus forming a total state control scheme. The design of the feedforward loop for a buck regulator is described. A possible implementation of the feedforward loop design is suggested.

Self-assembled nanostructures

CERN Document Server

Zhang, Jin Z; Liu, Jun; Chen, Shaowei; Liu, Gang-yu

2003-01-01

Nanostructures refer to materials that have relevant dimensions on the nanometer length scales and reside in the mesoscopic regime between isolated atoms and molecules in bulk matter. These materials have unique physical properties that are distinctly different from bulk materials. Self-Assembled Nanostructures provides systematic coverage of basic nanomaterials science including materials assembly and synthesis, characterization, and application. Suitable for both beginners and experts, it balances the chemistry aspects of nanomaterials with physical principles. It also highlights nanomaterial-based architectures including assembled or self-assembled systems. Filled with in-depth discussion of important applications of nano-architectures as well as potential applications ranging from physical to chemical and biological systems, Self-Assembled Nanostructures is the essential reference or text for scientists involved with nanostructures.

7 CFR 3430.607 - Stakeholder input.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Stakeholder input. 3430.607 Section 3430.607 Agriculture Regulations of the Department of Agriculture (Continued) COOPERATIVE STATE RESEARCH, EDUCATION... § 3430.607 Stakeholder input. CSREES shall seek and obtain stakeholder input through a variety of forums...

Vibration study of a vehicle suspension assembly with the finite element method

Science.gov (United States)

Cătălin Marinescu, Gabriel; Castravete, Ştefan-Cristian; Dumitru, Nicolae

2017-10-01

The main steps of the present work represent a methodology of analysing various vibration effects over suspension mechanical parts of a vehicle. A McPherson type suspension from an existing vehicle was created using CAD software. Using the CAD model as input, a finite element model of the suspension assembly was developed. Abaqus finite element analysis software was used to pre-process, solve, and post-process the results. Geometric nonlinearities are included in the model. Severe sources of nonlinearities such us friction and contact are also included in the model. The McPherson spring is modelled as linear spring. The analysis include several steps: preload, modal analysis, the reduction of the model to 200 generalized coordinates, a deterministic external excitation, a random excitation that comes from different types of roads. The vibration data used as an input for the simulation were previously obtained by experimental means. Mathematical expressions used for the simulation were also presented in the paper.

World Input-Output Network.

Directory of Open Access Journals (Sweden)

Federica Cerina

Full Text Available Production systems, traditionally analyzed as almost independent national systems, are increasingly connected on a global scale. Only recently becoming available, the World Input-Output Database (WIOD is one of the first efforts to construct the global multi-regional input-output (GMRIO tables. By viewing the world input-output system as an interdependent network where the nodes are the individual industries in different economies and the edges are the monetary goods flows between industries, we analyze respectively the global, regional, and local network properties of the so-called world input-output network (WION and document its evolution over time. At global level, we find that the industries are highly but asymmetrically connected, which implies that micro shocks can lead to macro fluctuations. At regional level, we find that the world production is still operated nationally or at most regionally as the communities detected are either individual economies or geographically well defined regions. Finally, at local level, for each industry we compare the network-based measures with the traditional methods of backward linkages. We find that the network-based measures such as PageRank centrality and community coreness measure can give valuable insights into identifying the key industries.

7 CFR 3430.15 - Stakeholder input.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Stakeholder input. 3430.15 Section 3430.15... Stakeholder input. Section 103(c)(2) of the Agricultural Research, Extension, and Education Reform Act of 1998... RFAs for competitive programs. CSREES will provide instructions for submission of stakeholder input in...

Input description for BIOPATH

International Nuclear Information System (INIS)

Marklund, J.E.; Bergstroem, U.; Edlund, O.

1980-01-01

The computer program BIOPATH describes the flow of radioactivity within a given ecosystem after a postulated release of radioactive material and the resulting dose for specified population groups. The present report accounts for the input data necessary to run BIOPATH. The report also contains descriptions of possible control cards and an input example as well as a short summary of the basic theory.(author)

Newnes electronics assembly handbook

CERN Document Server

Brindley, Keith

2013-01-01

Newnes Electronics Assembly Handbook: Techniques, Standards and Quality Assurance focuses on the aspects of electronic assembling. The handbook first looks at the printed circuit board (PCB). Base materials, basic mechanical properties, cleaning of assemblies, design, and PCB manufacturing processes are then explained. The text also discusses surface mounted assemblies and packaging of electromechanical assemblies, as well as the soldering process. Requirements for the soldering process; solderability and protective coatings; cleaning of PCBs; and mass solder/component reflow soldering are des

Modeling and generating input processes

Energy Technology Data Exchange (ETDEWEB)

Johnson, M.E.

1987-01-01

This tutorial paper provides information relevant to the selection and generation of stochastic inputs to simulation studies. The primary area considered is multivariate but much of the philosophy at least is relevant to univariate inputs as well. 14 refs.

Multimedia Environmental Pollutant Assessment System (MEPAS) application guidance. Guidelines for evaluating MEPAS input parameters for Version 3.1

International Nuclear Information System (INIS)

Buck, J.W.; Whelan, G.; Droppo, J.G. Jr.; Strenge, D.L.; Castleton, K.J.; McDonald, J.P.; Sato, C.; Streile, G.P.

1995-02-01

The Multimedia Environmental Pollutant Assessment System (MEPAS) was developed by Pacific Northwest Laboratory (PNL) for the U.S. Department of Energy (DOE) Office of Environment, Safety and Health and Office of Environmental Management and Environmental Restoration. MEPAS is a set of computer codes developed to provide decision makers with risk information integrated for hazardous, radioactive, and mixed-waste sites based on their potential hazard to public health. It is applicable to a wide range of environmental management and regulatory conditions, including inactive sites covered under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and active air and water releases covered under the Clean Air Act, the Clean Water Act, and the Resource Conservation and Recovery Act. MEPAS integrates contaminant release, transport, and exposure models into a single system. An interactive user interface assists the investigator in defining problems, assembling data and entering input, and developing reports. PNL has compiled two documents that explain the methodology behind the MEPAS model and instruct the user in how to input, retrieve, and evaluate data. This report contains detailed guidelines for defining the input data required to conduct an analysis with MEPAS. Entries for each variable have a short definition, units, and text explaining what a variable is and how it can be quantified. As appropriate, ranges and typical values are given. This report also contains listings of the input screens (worksheets) that are used in the MEPAS user interface for these variables

Fuel Assembly Damping Summary

Energy Technology Data Exchange (ETDEWEB)

Lee, Kanghee; Kang, Heungseok; Oh, Dongseok; Yoon, Kyungho; Kim, Hyungkyu; Kim, Jaeyong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

This paper summary the fuel assembly damping data in air/in still water/under flow, released from foreign fuel vendors, compared our data with the published data. Some technical issues in fuel assembly damping measurement testing are also briefly discussed. Understanding of each fuel assembly damping mechanisms according to the surrounding medium and flow velocity can support the fuel design improvement in fuel assembly dynamics and structural integrity aspect. Because the upgraded requirements of the newly-developed advanced reactor system will demands to minimize fuel design margin in integrity evaluation, reduction in conservatism of fuel assembly damping can contribute to alleviate the fuel design margin for sure. Damping is an energy dissipation mechanism in a vibrating mechanical structure and prevents a resonant structure from having infinite vibration amplitudes. The sources of fuel assembly damping are various from support friction to flow contribution, and it can be increased by the viscosity or drag of surrounding fluid medium or the average velocity of water flowing. Fuel licensing requires fuel design evaluation in transient or accidental condition. Dynamic response analysis of fuel assembly is to show fuel integrity and requires information on assembly-wise damping in dry condition and under wet or water flowing condition. However, damping measurement test for the full-scale fuel assembly prototype is not easy to carry out because of the scale (fuel prototype, test facility), unsteadiness of test data (scattering, random sampling and processing), instrumentation under water flowing (water-proof response measurement), and noise. LWR fuel technology division in KAERI is preparing the infra structure for damping measurement test of full-scale fuel assembly, to support fuel industries and related research activities. Here is a preliminary summary of fuel assembly damping, published in the literature. Some technical issues in fuel assembly damping

Characterization and drying of caja bagasse (Spondias mombin L. in a tray dryer using a factorial planning

Directory of Open Access Journals (Sweden)

Andréia Souto da Silva

2012-03-01

Full Text Available The caja (Spondias mombin L. is used in the manufacture of ice-cream, jams, pulps, beverages being also consumed in natura. One of the most important procedures in food conservation is drying, considering that most fresh fruits contain approximately 80% of water. Food drying is used to obtain two basic aspects: (1 the economic factor; in the shipping and handling of the product; (2 at the manipulation; once dried and grinded, the material is rehydrated, at desirable levels, to formulate a new product as in ice cream, jams, yoghurts and drinks and may also be added to pasta, biscuits and other industrialized products. The aim of this study was to investigate the kinetics of caja bagasse drying in a fixed-bed tray dryer, using central composite factorial planning. The following factors were evaluated: temperature (55, 65 and 75 ºC, dryer inlet air velocity (3.2, 4.6 and 6.0 m.s-1 and cake thickness (0.8, 1.2 and 1.6 cm where the response of the considered variable was caja bagasse moisture content (b.s. and the results showed that the main effects and their interactions were significant at a 95% confidence level being the best condition obtained at temperature of 75 ºC, velocity of 6.0 m.s-1 and cake thickness of 0.8 cm.

Wave energy input into the Ekman layer

Institute of Scientific and Technical Information of China (English)

2008-01-01

This paper is concerned with the wave energy input into the Ekman layer, based on 3 observational facts that surface waves could significantly affect the profile of the Ekman layer. Under the assumption of constant vertical diffusivity, the analytical form of wave energy input into the Ekman layer is derived. Analysis of the energy balance shows that the energy input to the Ekman layer through the wind stress and the interaction of the Stokes-drift with planetary vorticity can be divided into two kinds. One is the wind energy input, and the other is the wave energy input which is dependent on wind speed, wave characteristics and the wind direction relative to the wave direction. Estimates of wave energy input show that wave energy input can be up to 10% in high-latitude and high-wind speed areas and higher than 20% in the Antarctic Circumpolar Current, compared with the wind energy input into the classical Ekman layer. Results of this paper are of significance to the study of wave-induced large scale effects.

Fuel assembly

International Nuclear Information System (INIS)

Abe, Hideaki; Sakai, Takao; Ishida, Tomio; Yokota, Norikatsu.

1992-01-01

The lower ends of a plurality of plate-like shape memory alloys are secured at the periphery of the upper inside of the handling head of a fuel assembly. As the shape memory alloy, a Cu-Zn alloy, a Ti-Pd alloy or a Fe-Ni alloy is used. When high temperature coolants flow out to the handling head, the shape memory alloy deforms by warping to the outer side more greatly toward the upper portion thereof with the temperature increase of the coolants. As the result, the shape of the flow channel of the coolants is changed so as to enlarge at the exit of the upper end of the fuel assembly. Then, the pressure loss of the coolants in the fuel assembly is decreased by the enlargement. Accordingly, the flow rate of the coolants in the fuel assembly is increased to lower the temperature of the coolants. Further, high temperature coolants and low temperature coolants are mixed sufficiently just above the fuel assembly. This can suppress the temperature fluctuation of the mixed coolants in the upper portion of the reactor core, thereby enabling to decrease a fatigue and failures of the structural components in the upper portion of the reactor core. (I.N.)

Soldering in electronics assembly

CERN Document Server

Judd, Mike

2013-01-01

Soldering in Electronics Assembly discusses several concerns in soldering of electronic assemblies. The book is comprised of nine chapters that tackle different areas in electronic assembly soldering. Chapter 1 discusses the soldering process itself, while Chapter 2 covers the electronic assemblies. Chapter 3 talks about solders and Chapter 4 deals with flux. The text also tackles the CS and SC soldering process. The cleaning of soldered assemblies, solder quality, and standards and specifications are also discussed. The book will be of great use to professionals who deal with electronic assem

Multivalent protein assembly using monovalent self-assembling building blocks

NARCIS (Netherlands)

Petkau - Milroy, K.; Sonntag, M.H.; Colditz, A.; Brunsveld, L.

2013-01-01

Discotic molecules, which self-assemble in water into columnar supramolecular polymers, emerged as an alternative platform for the organization of proteins. Here, a monovalent discotic decorated with one single biotin was synthesized to study the self-assembling multivalency of this system in regard

Burnup code for fuel assembly by Monte Carlo code. MKENO-BURN

International Nuclear Information System (INIS)

Naito, Yoshitaka; Suyama, Kenya; Masukawa, Fumihiro; Matsumoto, Kiyoshi; Kurosawa, Masayoshi; Kaneko, Toshiyuki.

1996-12-01

The evaluation of neutron spectrum is so important for burnup calculation of the heterogeneous geometry like recent BWR fuel assembly. MKENO-BURN is a multi dimensional burnup code that based on the three dimensional monte carlo neutron transport code 'MULTI-KENO' and the routine for the burnup calculation of the one dimensional burnup code 'UNITBURN'. MKENO-BURN analyzes the burnup problem of arbitrary regions after evaluating the neutron spectrum and making one group cross section in three dimensional geometry with MULTI-KENO. It enables us to do three dimensional burnup calculation. This report consists of general description of MKENO-BURN and the input data. (author)

Burnup code for fuel assembly by Monte Carlo code. MKENO-BURN

Energy Technology Data Exchange (ETDEWEB)

Naito, Yoshitaka; Suyama, Kenya; Masukawa, Fumihiro; Matsumoto, Kiyoshi; Kurosawa, Masayoshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kaneko, Toshiyuki

1996-12-01

The evaluation of neutron spectrum is so important for burnup calculation of the heterogeneous geometry like recent BWR fuel assembly. MKENO-BURN is a multi dimensional burnup code that based on the three dimensional monte carlo neutron transport code `MULTI-KENO` and the routine for the burnup calculation of the one dimensional burnup code `UNITBURN`. MKENO-BURN analyzes the burnup problem of arbitrary regions after evaluating the neutron spectrum and making one group cross section in three dimensional geometry with MULTI-KENO. It enables us to do three dimensional burnup calculation. This report consists of general description of MKENO-BURN and the input data. (author)

Bearing assemblies, apparatuses, and motor assemblies using the same

Science.gov (United States)

Sexton, Timothy N.; Cooley, Craig H.; Knuteson, Cody W.

2015-12-29

Various embodiments of the invention relate to bearing assemblies, apparatuses and motor assemblies that include geometric features configured to impart a selected amount of heat transfer and/or hydrodynamic film formation. In an embodiment, a bearing assembly may include a plurality of superhard bearing pads distributed circumferentially about an axis. At least some of the plurality of superhard bearing pads may include a plurality of sub-superhard bearing elements defining a bearing surface. At least some of the plurality of sub-superhard bearing elements may be spaced from one another by one or more voids to impart a selected amount of heat transfer and hydrodynamic film formation thereon during operation. The bearing assembly may also include a support ring that carries the plurality of superhard bearing pads. In addition, at least a portion of the sub-superhard bearing elements may extend beyond the support ring.

Identification of biomechanical nonlinearity in whole-body vibration using a reverse path multi-input-single-output method

Science.gov (United States)

Huang, Ya; Ferguson, Neil S.

2018-04-01

The study implements a classic signal analysis technique, typically applied to structural dynamics, to examine the nonlinear characteristics seen in the apparent mass of a recumbent person during whole-body horizontal random vibration. The nonlinearity in the present context refers to the amount of 'output' that is not correlated or coherent to the 'input', usually indicated by values of the coherence function that are less than unity. The analysis is based on the longitudinal horizontal inline and vertical cross-axis apparent mass of twelve human subjects exposed to 0.25-20 Hz random acceleration vibration at 0.125 and 1.0 ms-2 r.m.s. The conditioned reverse path frequency response functions (FRF) reveal that the uncorrelated 'linear' relationship between physical input (acceleration) and outputs (inline and cross-axis forces) has much greater variation around the primary resonance frequency between 0.5 and 5 Hz. By reversing the input and outputs of the physical system, it is possible to assemble additional mathematical inputs from the physical output forces and mathematical constructs (e.g. square root of inline force). Depending on the specific construct, this can improve the summed multiple coherence at frequencies where the response magnitude is low. In the present case this is between 6 and 20 Hz. The statistical measures of the response force time histories of each of the twelve subjects indicate that there are potential anatomical 'end-stops' for the sprung mass in the inline axis. No previous study has applied this reverse path multi-input-single-output approach to human vibration kinematic and kinetic data before. The implementation demonstrated in the present study will allow new and existing data to be examined using this different analytical tool.

Fuel assembly

International Nuclear Information System (INIS)

Gjertsen, R.K.; Bassler, E.A.; Huckestein, E.A.; Salton, R.B.; Tower, S.N.

1988-01-01

A fuel assembly adapted for use with a pressurized water nuclear reactor having capabilities for fluid moderator spectral shift control is described comprising: parallel arranged elongated nuclear fuel elements; means for providing for axial support of the fuel elements and for arranging the fuel elements in a spaced array; thimbles interspersed among the fuel elements adapted for insertion of a rod control cluster therewithin; means for structurally joining the fuel elements and the guide thimbles; fluid moderator control means for providing a volume of low neutron absorbing fluid within the fuel assembly and for removing a substantially equivalent volume of reactor coolant water therefrom, a first flow manifold at one end of the fuel assembly sealingly connected to a first end of the moderator control tubes whereby the first ends are commonly flow connected; and a second flow manifold, having an inlet passage and an outlet passage therein, sealingly connected to a second end of the moderator control tubes at a second end of the fuel assembly

Self assembly of organic nanostructures and dielectrophoretic assembly of inorganic nanowires.

Science.gov (United States)

Dholakia, Geetha; Kuo, Steven; Allen, E. L.

2007-03-01

Self assembly techniques enable the organization of organic molecules into nanostructures. Currently engineering strategies for efficient assembly and routine integration of inorganic nanoscale objects into functional devices is very limited. AC Dielectrophoresis is an efficient technique to manipulate inorganic nanomaterials into higher dimensional structures. We used an alumina template based sol-gel synthesis method for the growth of various metal oxide nanowires with typical diameters of 100-150 nm, ranging in length from 3-10 μm. Here we report the dielectrophoretic assembly of TiO2 nanowires, an important material for photocatalysis and photovoltaics, onto interdigitated devices. Self assembly in organic nanostructures and its dependence on structure and stereochemistry of the molecule and dielectrophoretic field dependence in the assembly of inorganic nanowires will be compared and contrasted. Tunneling spectroscopy and DOS of these nanoscale systems will also be discussed.

Fire resistant PV shingle assembly

Science.gov (United States)

Lenox, Carl J.

2012-10-02

A fire resistant PV shingle assembly includes a PV assembly, including PV body, a fire shield and a connection member connecting the fire shield below the PV body, and a support and inter-engagement assembly. The support and inter-engagement assembly is mounted to the PV assembly and comprises a vertical support element, supporting the PV assembly above a support surface, an upper interlock element, positioned towards the upper PV edge, and a lower interlock element, positioned towards the lower PV edge. The upper interlock element of one PV shingle assembly is inter-engageable with the lower interlock element of an adjacent PV shingle assembly. In some embodiments the PV shingle assembly may comprise a ventilation path below the PV body. The PV body may be slidably mounted to the connection member to facilitate removal of the PV body.

Nuclear reactor fuel assembly

International Nuclear Information System (INIS)

Marmonier, Pierre; Mesnage, Bernard; Nervi, J.C.

1975-01-01

This invention refers to fuel assemblies for a liquid metal cooled fast neutron reactor. Each assembly is composed of a hollow vertical casing, of regular polygonal section, containing a bundle of clad pins filled with a fissile or fertile substance. The casing is open at its upper end and has a cylindrical foot at its lower end for positioning the assembly in a housing provided in the horizontal diagrid, on which the core assembly rests. A set of flat bars located on the external surface of the casing enables it to be correctly orientated in its housing among the other core assemblies [fr

Statistical identification of effective input variables

International Nuclear Information System (INIS)

Vaurio, J.K.

1982-09-01

A statistical sensitivity analysis procedure has been developed for ranking the input data of large computer codes in the order of sensitivity-importance. The method is economical for large codes with many input variables, since it uses a relatively small number of computer runs. No prior judgemental elimination of input variables is needed. The sceening method is based on stagewise correlation and extensive regression analysis of output values calculated with selected input value combinations. The regression process deals with multivariate nonlinear functions, and statistical tests are also available for identifying input variables that contribute to threshold effects, i.e., discontinuities in the output variables. A computer code SCREEN has been developed for implementing the screening techniques. The efficiency has been demonstrated by several examples and applied to a fast reactor safety analysis code (Venus-II). However, the methods and the coding are general and not limited to such applications

Systemic analysis of the caulking assembly process

Directory of Open Access Journals (Sweden)

Rodean Claudiu

2017-01-01

Full Text Available The present paper highlights the importance of a caulking process which is nowadays less studied in comparison with the growing of its usage in the automotive industry. Due to the fact that the caulking operation is used in domains with high importance such as shock absorbers and brake systems there comes the demand of this paper to detail the parameters which characterize the process, viewed as input data and output data, and the requirements asked for the final product. The paper presents the actual measurement methods used for analysis the performance of the caulking assembly. All this parameters leads to an analysis algorithm of performance established for the caulking process which it is used later in the paper for an experimental research. The study is a basis from which it will be able to go to further researches in order to optimize the following processing.

Gestures and multimodal input

OpenAIRE

Keates, Simeon; Robinson, Peter

1999-01-01

For users with motion impairments, the standard keyboard and mouse arrangement for computer access often presents problems. Other approaches have to be adopted to overcome this. In this paper, we will describe the development of a prototype multimodal input system based on two gestural input channels. Results from extensive user trials of this system are presented. These trials showed that the physical and cognitive loads on the user can quickly become excessive and detrimental to the interac...

The Importance of Input and Interaction in SLA

Institute of Scientific and Technical Information of China (English)

党春花

2009-01-01

As is known to us, input and interaction play the crucial roles in second language acquisition (SLA). Different linguistic schools have different explanations to input and interaction Behaviorist theories hold a view that input is composed of stimuli and response, putting more emphasis on the importance of input, while mentalist theories find input is a necessary condition to SLA, not a sufficient condition. At present, social interaction theories, which is one type of cognitive linguistics, suggests that besides input, interaction is also essential to language acquisition. Then, this essay will discuss how input and interaction result in SLA.

Rapid hybrid de novo assembly of a microbial genome using only short reads: Corynebacterium pseudotuberculosis I19 as a case study.

Science.gov (United States)

Cerdeira, Louise Teixeira; Carneiro, Adriana Ribeiro; Ramos, Rommel Thiago Jucá; de Almeida, Sintia Silva; D'Afonseca, Vivian; Schneider, Maria Paula Cruz; Baumbach, Jan; Tauch, Andreas; McCulloch, John Anthony; Azevedo, Vasco Ariston Carvalho; Silva, Artur

2011-08-01

Due to the advent of the so-called Next-Generation Sequencing (NGS) technologies the amount of monetary and temporal resources for whole-genome sequencing has been reduced by several orders of magnitude. Sequence reads can be assembled either by anchoring them directly onto an available reference genome (classical reference assembly), or can be concatenated by overlap (de novo assembly). The latter strategy is preferable because it tends to maintain the architecture of the genome sequence the however, depending on the NGS platform used, the shortness of read lengths cause tremendous problems the in the subsequent genome assembly phase, impeding closing of the entire genome sequence. To address the problem, we developed a multi-pronged hybrid de novo strategy combining De Bruijn graph and Overlap-Layout-Consensus methods, which was used to assemble from short reads the entire genome of Corynebacterium pseudotuberculosis strain I19, a bacterium with immense importance in veterinary medicine that causes Caseous Lymphadenitis in ruminants, principally ovines and caprines. Briefly, contigs were assembled de novo from the short reads and were only oriented using a reference genome by anchoring. Remaining gaps were closed using iterative anchoring of short reads by craning to gap flanks. Finally, we compare the genome sequence assembled using our hybrid strategy to a classical reference assembly using the same data as input and show that with the availability of a reference genome, it pays off to use the hybrid de novo strategy, rather than a classical reference assembly, because more genome sequences are preserved using the former. Copyright © 2011 Elsevier B.V. All rights reserved.

Self assembly of rectangular shapes on concentration programming and probabilistic tile assembly models.

Science.gov (United States)

Kundeti, Vamsi; Rajasekaran, Sanguthevar

2012-06-01

Efficient tile sets for self assembling rectilinear shapes is of critical importance in algorithmic self assembly. A lower bound on the tile complexity of any deterministic self assembly system for an n × n square is [Formula: see text] (inferred from the Kolmogrov complexity). Deterministic self assembly systems with an optimal tile complexity have been designed for squares and related shapes in the past. However designing [Formula: see text] unique tiles specific to a shape is still an intensive task in the laboratory. On the other hand copies of a tile can be made rapidly using PCR (polymerase chain reaction) experiments. This led to the study of self assembly on tile concentration programming models. We present two major results in this paper on the concentration programming model. First we show how to self assemble rectangles with a fixed aspect ratio ( α:β ), with high probability, using Θ( α + β ) tiles. This result is much stronger than the existing results by Kao et al. (Randomized self-assembly for approximate shapes, LNCS, vol 5125. Springer, Heidelberg, 2008) and Doty (Randomized self-assembly for exact shapes. In: proceedings of the 50th annual IEEE symposium on foundations of computer science (FOCS), IEEE, Atlanta. pp 85-94, 2009)-which can only self assembly squares and rely on tiles which perform binary arithmetic. On the other hand, our result is based on a technique called staircase sampling . This technique eliminates the need for sub-tiles which perform binary arithmetic, reduces the constant in the asymptotic bound, and eliminates the need for approximate frames (Kao et al. Randomized self-assembly for approximate shapes, LNCS, vol 5125. Springer, Heidelberg, 2008). Our second result applies staircase sampling on the equimolar concentration programming model (The tile complexity of linear assemblies. In: proceedings of the 36th international colloquium automata, languages and programming: Part I on ICALP '09, Springer-Verlag, pp 235

Assembling large, complex environmental metagenomes

Energy Technology Data Exchange (ETDEWEB)

Howe, A. C. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Plant Soil and Microbial Sciences; Jansson, J. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Earth Sciences Division; Malfatti, S. A. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Tringe, S. G. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Tiedje, J. M. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Plant Soil and Microbial Sciences; Brown, C. T. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Computer Science and Engineering

2012-12-28

The large volumes of sequencing data required to sample complex environments deeply pose new challenges to sequence analysis approaches. De novo metagenomic assembly effectively reduces the total amount of data to be analyzed but requires significant computational resources. We apply two pre-assembly filtering approaches, digital normalization and partitioning, to make large metagenome assemblies more computationaly tractable. Using a human gut mock community dataset, we demonstrate that these methods result in assemblies nearly identical to assemblies from unprocessed data. We then assemble two large soil metagenomes from matched Iowa corn and native prairie soils. The predicted functional content and phylogenetic origin of the assembled contigs indicate significant taxonomic differences despite similar function. The assembly strategies presented are generic and can be extended to any metagenome; full source code is freely available under a BSD license.

Nuclear fuel string assembly

International Nuclear Information System (INIS)

Ip, A.K.; Koyanagi, K.; Tarasuk, W.R.

1976-01-01

A method of fabricating rodded fuels suitable for use in pressure tube type reactors and in pressure vessel type reactors is described. Fuel rods are secured as an inner and an outer sub-assembly, each rod attached between mounting rings secured to the rod ends. The two sub-assemblies are telescoped together and positioned by spaced thimbles located between them to provide precise positioning while permittng differential axial movement between the sub-assemblies. Such sub-assemblies are particularly suited for mounting as bundle strings. The method provides particular advantages in the assembly of annular-section fuel pins, which includes booster fuel containing enriched fuel material. (LL)

Fuel assembly reconstitution

International Nuclear Information System (INIS)

Morgado, Mario M.; Oliveira, Monica G.N.; Ferreira Junior, Decio B.M.; Santos, Barbara O. dos; Santos, Jorge E. dos

2009-01-01

Fuel failures have been happened in Nuclear Power Plants worldwide, without lost of integrity and safety, mainly for the public, environment and power plants workers. The most common causes of these events are corrosion (CRUD), fretting and pellet cladding interaction. These failures are identified by increasing the activity of fission products, verified by chemical analyses of reactor coolant. Through these analyses, during the fourth operation cycle of Angra 2 Nuclear Power Plant, was possible to observe fuel failure indication. This indication was confirmed in the end of the cycle during the unloading of reactor core through leakage tests of fuel assembly, using the equipment called 'In Mast Sipping' and 'Box Sipping'. After confirmed, the fuel assembly reconstitution was scheduled, and happened in April, 2007, where was identified the cause and the fuel rod failure, which was substitute by dummy rods (zircaloy). The cause was fretting by 'debris'. The actions to avoid and prevent fuel assemblies failures are important. The goals of this work are to describe the methodology of fuel assembly reconstitution using the FARE (Fuel Assembly Reconstitution Equipment) system, to describe the results of this task in economic and security factors of the company and show how the fuel assembly failures are identified during operation and during the outage. (author)

Feasibility analysis of vacuum sieve tray for tritium extraction in the HCLL test blanket system

Energy Technology Data Exchange (ETDEWEB)

Okino, Fumito, E-mail: fumito.okino@iae.kyoto-u.ac.jp [Kyoto University Institute of Advanced Energy, 611-0011 Gokasho, Uji, Kyoto (Japan); Calderoni, Pattrick [Fusion For Energy, 08019 Barcelona (Spain); Kasada, Ryuta; Konishi, Satoshi [Kyoto University Institute of Advanced Energy, 611-0011 Gokasho, Uji, Kyoto (Japan)

2016-11-01

Highlights: • The authors discovered faster mass transport on a droplet falling in a vacuum. • Primary cause of the hydrogen release from droplet is by the oscillation of a droplet. • The spherical oscillation induces the internal advection and enhances mass transfer. • This assumption agreed with previous experimental results. - Abstract: This paper describes the quantitative analysis for the design of a tritium extraction system that uses liquid PbLi droplets in vacuum (Vacuum Sieve Tray, VST), for application to the ITER helium-cooled lithium lead (HCLL) test blanket system (TBS). The parametric dependences of tritium extraction efficiency from the main geometrical features such as initial droplet velocity, nozzle head height, nozzle diameter, and flow rate are discussed. With nozzle diameters between 0.4 and 0.6 mm, extraction efficiency is estimated from 0.77 to 0.96 at the falling height of 0.5 m, with flow rate between 0.2 and 1.0 kg/s. The device has a height of 1.6 m, within the external dimensions of the HCLL Test Blanket Module (TBM), and no additional pumping power is required. The attained results are considered attractive not only for ITER, but also in view of the application of the VST concept as a candidate tritium extraction system for the European Union's demonstration fusion reactor (DEMO). The extraction efficiency of a single droplet column, which is the basis of the design analysis presented, has been validated experimentally with hydrogen. However, further experiments are required on an integrated system with size relevant to the proposed HCLL-TBS design to validate system-level effects, particularly regarding the desorption process in an array of multiple droplets.

Analysis on relation between safety input and accidents

Institute of Scientific and Technical Information of China (English)

YAO Qing-guo; ZHANG Xue-mu; LI Chun-hui

2007-01-01

The number of safety input directly determines the level of safety, and there exists dialectical and unified relations between safety input and accidents. Based on the field investigation and reliable data, this paper deeply studied the dialectical relationship between safety input and accidents, and acquired the conclusions. The security situation of the coal enterprises was related to the security input rate, being effected little by the security input scale, and build the relationship model between safety input and accidents on this basis, that is the accident model.

Reflector-moderated critical assemblies

International Nuclear Information System (INIS)

Paxton, H.C.; Jarvis, G.A.; Byers, C.C.

1975-07-01

Experiments with reflector-moderated critical assemblies were part of the Rover Program at the Los Alamos Scientific Laboratory (LASL). These assemblies were characterized by thick D 2 O or beryllium reflectors surrounding large cavities that contained highly enriched uranium at low average densities. Because interest in this type of system has been revived by LASL Plasma Cavity Assembly studies, more detailed descriptions of the early assemblies than had been available in the unclassified literature are provided. (U.S.)

Measuring Input Thresholds on an Existing Board

Science.gov (United States)

Kuperman, Igor; Gutrich, Daniel G.; Berkun, Andrew C.

2011-01-01

A critical PECL (positive emitter-coupled logic) interface to Xilinx interface needed to be changed on an existing flight board. The new Xilinx input interface used a CMOS (complementary metal-oxide semiconductor) type of input, and the driver could meet its thresholds typically, but not in worst-case, according to the data sheet. The previous interface had been based on comparison with an external reference, but the CMOS input is based on comparison with an internal divider from the power supply. A way to measure what the exact input threshold was for this device for 64 inputs on a flight board was needed. The measurement technique allowed an accurate measurement of the voltage required to switch a Xilinx input from high to low for each of the 64 lines, while only probing two of them. Directly driving an external voltage was considered too risky, and tests done on any other unit could not be used to qualify the flight board. The two lines directly probed gave an absolute voltage threshold calibration, while data collected on the remaining 62 lines without probing gave relative measurements that could be used to identify any outliers. The PECL interface was forced to a long-period square wave by driving a saturated square wave into the ADC (analog to digital converter). The active pull-down circuit was turned off, causing each line to rise rapidly and fall slowly according to the input s weak pull-down circuitry. The fall time shows up as a change in the pulse width of the signal ready by the Xilinx. This change in pulse width is a function of capacitance, pulldown current, and input threshold. Capacitance was known from the different trace lengths, plus a gate input capacitance, which is the same for all inputs. The pull-down current is the same for all inputs including the two that are probed directly. The data was combined, and the Excel solver tool was used to find input thresholds for the 62 lines. This was repeated over different supply voltages and

Mars 2.2 code manual: input requirements

International Nuclear Information System (INIS)

Chung, Bub Dong; Lee, Won Jae; Jeong, Jae Jun; Lee, Young Jin; Hwang, Moon Kyu; Kim, Kyung Doo; Lee, Seung Wook; Bae, Sung Won

2003-07-01

Korea Advanced Energy Research Institute (KAERI) conceived and started the development of MARS code with the main objective of producing a state-of-the-art realistic thermal hydraulic systems analysis code with multi-dimensional analysis capability. MARS achieves this objective by very tightly integrating the one dimensional RELAP5/MOD3 with the multi-dimensional COBRA-TF codes. The method of integration of the two codes is based on the dynamic link library techniques, and the system pressure equation matrices of both codes are implicitly integrated and solved simultaneously. In addition, the Equation-of-State (EOS) for the light water was unified by replacing the EOS of COBRA-TF by that of the RELAP5. This input manual provides a complete list of input required to run MARS. The manual is divided largely into two parts, namely, the one-dimensional part and the multi-dimensional part. The inputs for auxiliary parts such as minor edit requests and graph formatting inputs are shared by the two parts and as such mixed input is possible. The overall structure of the input is modeled on the structure of the RELAP5 and as such the layout of the manual is very similar to that of the RELAP. This similitude to RELAP5 input is intentional as this input scheme will allow minimum modification between the inputs of RELAP5 and MARS. MARS development team would like to express its appreciation to the RELAP5 Development Team and the USNRC for making this manual possible

MARS code manual volume II: input requirements

International Nuclear Information System (INIS)

Chung, Bub Dong; Kim, Kyung Doo; Bae, Sung Won; Jeong, Jae Jun; Lee, Seung Wook; Hwang, Moon Kyu

2010-02-01

Korea Advanced Energy Research Institute (KAERI) conceived and started the development of MARS code with the main objective of producing a state-of-the-art realistic thermal hydraulic systems analysis code with multi-dimensional analysis capability. MARS achieves this objective by very tightly integrating the one dimensional RELAP5/MOD3 with the multi-dimensional COBRA-TF codes. The method of integration of the two codes is based on the dynamic link library techniques, and the system pressure equation matrices of both codes are implicitly integrated and solved simultaneously. In addition, the Equation-Of-State (EOS) for the light water was unified by replacing the EOS of COBRA-TF by that of the RELAP5. This input manual provides a complete list of input required to run MARS. The manual is divided largely into two parts, namely, the one-dimensional part and the multi-dimensional part. The inputs for auxiliary parts such as minor edit requests and graph formatting inputs are shared by the two parts and as such mixed input is possible. The overall structure of the input is modeled on the structure of the RELAP5 and as such the layout of the manual is very similar to that of the RELAP. This similitude to RELAP5 input is intentional as this input scheme will allow minimum modification between the inputs of RELAP5 and MARS3.1. MARS3.1 development team would like to express its appreciation to the RELAP5 Development Team and the USNRC for making this manual possible

Impact of measurement approach on the quality of gamma scanning density profile in a tray type lab-scale column

International Nuclear Information System (INIS)

Shahabinejad, H.; Feghhi, S.A.H.; Khorsandi, M.

2014-01-01

This article presents a study for investigating impact of the measurement approach on the quality of gamma scanning density profile in tray type columns using experimental and computational evaluations. Experimental density profiles from the total and the photopeak count measurements, as two approaches in gamma ray column scanning technique, has been compared with the computational density profile from Monte Carlo simulation results. We used a laboratory distillation column of 51 cm diameter as an illustrative example for this investigation. 137 Cs was used as a gamma ray source with the activity of 296 MBq (8 mCi), with a NaI(Tl) detector. MCNP4C Monte Carlo code has been used for simulations. The quality of the density profile in the photopeak count approach is relatively within 155–204% better than that of the total count approach for experimental results. The same comparison for simulation results leads to a relative difference within 100–135% for the density profile. - Highlights: • The quality of density profile in gamma scanning technique has been studied. • Quality of density profile depends on the measurement approach. • A laboratory distillation column has been used as an illustrative example. • MCNP4C Monte Carlo code has been used for simulations

Robust input design for nonlinear dynamic modeling of AUV.

Science.gov (United States)

Nouri, Nowrouz Mohammad; Valadi, Mehrdad

2017-09-01

Input design has a dominant role in developing the dynamic model of autonomous underwater vehicles (AUVs) through system identification. Optimal input design is the process of generating informative inputs that can be used to generate the good quality dynamic model of AUVs. In a problem with optimal input design, the desired input signal depends on the unknown system which is intended to be identified. In this paper, the input design approach which is robust to uncertainties in model parameters is used. The Bayesian robust design strategy is applied to design input signals for dynamic modeling of AUVs. The employed approach can design multiple inputs and apply constraints on an AUV system's inputs and outputs. Particle swarm optimization (PSO) is employed to solve the constraint robust optimization problem. The presented algorithm is used for designing the input signals for an AUV, and the estimate obtained by robust input design is compared with that of the optimal input design. According to the results, proposed input design can satisfy both robustness of constraints and optimality. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Polymer Directed Protein Assemblies

NARCIS (Netherlands)

van Rijn, Patrick

2013-01-01

Protein aggregation and protein self-assembly is an important occurrence in natural systems, and is in some form or other dictated by biopolymers. Very obvious influences of biopolymers on protein assemblies are, e. g., virus particles. Viruses are a multi-protein assembly of which the morphology is

Core/coil assembly for use in superconducting magnets and method for assembling the same

Science.gov (United States)

Kassner, David A.

1979-01-01

A core/coil assembly for use in a superconducting magnet of the focusing or bending type used in syncronous particle accelerators comprising a coil assembly contained within an axial bore of the stacked, washer type, carbon steel laminations which comprise the magnet core assembly, and forming an interference fit with said laminations at the operating temperature of said magnet. Also a method for making such core/coil assemblies comprising the steps of cooling the coil assembly to cryogenic temperatures and drawing it rapidly upwards into the bore of said stacked laminations.

Six axis force feedback input device

Science.gov (United States)

Ohm, Timothy (Inventor)

1998-01-01

The present invention is a low friction, low inertia, six-axis force feedback input device comprising an arm with double-jointed, tendon-driven revolute joints, a decoupled tendon-driven wrist, and a base with encoders and motors. The input device functions as a master robot manipulator of a microsurgical teleoperated robot system including a slave robot manipulator coupled to an amplifier chassis, which is coupled to a control chassis, which is coupled to a workstation with a graphical user interface. The amplifier chassis is coupled to the motors of the master robot manipulator and the control chassis is coupled to the encoders of the master robot manipulator. A force feedback can be applied to the input device and can be generated from the slave robot to enable a user to operate the slave robot via the input device without physically viewing the slave robot. Also, the force feedback can be generated from the workstation to represent fictitious forces to constrain the input device's control of the slave robot to be within imaginary predetermined boundaries.

Model and simulation of a vacuum sieve tray for T extraction from liquid PbLi breeding blankets

International Nuclear Information System (INIS)

Mertens, M.A.J.; Demange, D.; Frances, L.

2016-01-01

Highlights: • A simulation tool was developed to analyse, optimise and scale up VST set-ups. • This tool predicts that efficiencies higher than 90% can be reached. • Upscaling to DEMO breeding blanket flow rates results in feasibly sized designs. - Abstract: Tritium self-sufficiency within a nuclear fusion reactor is necessary to demonstrate nuclear fusion as a viable source of energy. Tritium can be produced within liquid eutectic PbLi but then has to be extracted to be refuelled to the plasma. The vacuum sieve tray (VST) method is based on the extraction of tritium from millimetre-scaled oscillating PbLi droplets falling inside a vacuum chamber. A simulation tool was developed describing the fluid dynamics occurring along the PbLi flow and was used to study the influence of the different geometrical and operational parameters on the VST performance. The simulation predicts that extraction efficiencies over 90% can be easily reached according to theory and previous experimental results. The size of the VST extraction unit for a fusion reactor is estimated based on the findings from our single-nozzle model and assuming no T reabsorption. It is found to be in the feasible range. Nevertheless, two approaches are discussed which may further reduce this size by up to 90%. The simulation tool proved to be an easy and powerful way to analyse and optimise VST set-ups at any scale.

Leaders’ receptivity to subordinates’ creative input: the role of achievement goals and composition of creative input

NARCIS (Netherlands)

Sijbom, R.B.L.; Janssen, O.; van Yperen, N.W.

2015-01-01

We identified leaders’ achievement goals and composition of creative input as important factors that can clarify when and why leaders are receptive to, and supportive of, subordinates’ creative input. As hypothesized, in two experimental studies, we found that relative to mastery goal leaders,

Nuclear fuel assemblies and fuel pins usable in such assemblies

International Nuclear Information System (INIS)

Jolly, R.

1982-01-01

A novel end cap for a nuclear fuel assembly is described in detail. It consists of a trisection arrangement which is received within a cell of a cellular grid. The cell contains abutment means with which the trisection comes into abutment. The grid also contains an abutment means for preventing the trisections from being inserted into the cell in an incorrect orientation. The present design allows fuel pins to be securely held in a hold-down grid of a sub-assembly. The design also allows easier dis-assembly of the swollen and embrittled fuel pins prior to reprocessing. (U.K.)

High-frequency matrix converter with square wave input

Science.gov (United States)

Carr, Joseph Alexander; Balda, Juan Carlos

2015-03-31

A device for producing an alternating current output voltage from a high-frequency, square-wave input voltage comprising, high-frequency, square-wave input a matrix converter and a control system. The matrix converter comprises a plurality of electrical switches. The high-frequency input and the matrix converter are electrically connected to each other. The control system is connected to each switch of the matrix converter. The control system is electrically connected to the input of the matrix converter. The control system is configured to operate each electrical switch of the matrix converter converting a high-frequency, square-wave input voltage across the first input port of the matrix converter and the second input port of the matrix converter to an alternating current output voltage at the output of the matrix converter.

Self-assembly of coiled coil peptides into nanoparticles vs 2-d plates: effects of assembly pathway

Science.gov (United States)

Kim, Kyunghee; Pochan, Darrin

Molecular solution assembly, or self-assembly, is a process by which ordered nanostructures or patterns are formed by non-covalent interactions during assembly. Biomimicry, the use of bioinspired molecules or biologically relevant materials, is an important area of self-assembly research with peptides serving a critical role as molecular tools. The morphology of peptide assemblies can be controlled by adjusting solution conditions such as the concentration of peptides, the temperature, and pH. Herein, spherical nanostructures, which have potential for creating an encapsulation system, are formed by self-assembly when coiled coil peptides are combined in solution. These peptides are homotrimeric and heterodimeric coiled-coil bundles and the homotrimer is connected with each of heterodimer through their external surfaces via disulfide bonds. The resultant covalent constructs could co-assemble into complementary trimeric hubs, respectively. The two peptide constructs are directly mixed and assembled in solution in order to produce either spherical particles or 2-d plates depending on the solution conditions and kinetic pathway of assembly. In particular, structural changes of the self-assembled peptides are explored by control of the thermal history of the assembly solution.

Rapid centriole assembly in Naegleria reveals conserved roles for both de novo and mentored assembly.

Science.gov (United States)

Fritz-Laylin, Lillian K; Levy, Yaron Y; Levitan, Edward; Chen, Sean; Cande, W Zacheus; Lai, Elaine Y; Fulton, Chandler

2016-03-01

Centrioles are eukaryotic organelles whose number and position are critical for cilia formation and mitosis. Many cell types assemble new centrioles next to existing ones ("templated" or mentored assembly). Under certain conditions, centrioles also form without pre-existing centrioles (de novo). The synchronous differentiation of Naegleria amoebae to flagellates represents a unique opportunity to study centriole assembly, as nearly 100% of the population transitions from having no centrioles to having two within minutes. Here, we find that Naegleria forms its first centriole de novo, immediately followed by mentored assembly of the second. We also find both de novo and mentored assembly distributed among all major eukaryote lineages. We therefore propose that both modes are ancestral and have been conserved because they serve complementary roles, with de novo assembly as the default when no pre-existing centriole is available, and mentored assembly allowing precise regulation of number, timing, and location of centriole assembly. © 2016 Wiley Periodicals, Inc.

Next-generation transcriptome assembly

Energy Technology Data Exchange (ETDEWEB)

Martin, Jeffrey A.; Wang, Zhong

2011-09-01

Transcriptomics studies often rely on partial reference transcriptomes that fail to capture the full catalog of transcripts and their variations. Recent advances in sequencing technologies and assembly algorithms have facilitated the reconstruction of the entire transcriptome by deep RNA sequencing (RNA-seq), even without a reference genome. However, transcriptome assembly from billions of RNA-seq reads, which are often very short, poses a significant informatics challenge. This Review summarizes the recent developments in transcriptome assembly approaches - reference-based, de novo and combined strategies-along with some perspectives on transcriptome assembly in the near future.

Evolution of fuel rod support under irradiation consequences on the mechanical behavior of fuel assembly

International Nuclear Information System (INIS)

Billerey, A.; Bouffioux, P.

2002-01-01

The complete paper follows. According to the fuel management policy in French PWR with respect to high burn-up, the prediction of the mechanical behavior of the irradiated fuel assembly is required as far as excessive deformations of fuel assembly might lead to incomplete Rod Cluster Control Assembly insertion (safety problems) and fretting wear lead to leaking rods (plant operation problems). One of the most important parameter is the evolution of the fuel rod support in the grid cell as it directly governs the mechanical behavior of the fuel assembly and consequently allows to predict the behavior of irradiated structure in terms of (i) axial and lateral deformation (global behavior of the assembly) and (ii) fretting wear (local behavior of the rod). Fuel rod support is provided by a spring-dimple system fixed on the grid. During irradiation, the spring force decreases and a gap between the rod and the spring might open. This phenomenon is due to (i) irradiation-induced stress relaxation for the spring and for the dimples, (ii) grid growth and (iii) reduction of rod diameter. Two models have been developed to predict the behavior of the rod in the grid cell. The first model is able to evaluate the spring force relaxation during irradiation. The second one is able to evaluate the rotation characteristic of the fuel rod in the cell, function of the spring force. The main input parameters are (i) the creep laws of the grid materials, (ii) the growth law of the grid, (iii) the evolution of rod diameter and (iv) the design of the fuel rod support. The objectives of this paper are to: (i) evaluate the consequences of grid support design modifications on the fretting sensitivity in terms of predicted maximum gap during irradiation and operational time to gap appearance; (ii) evaluate, using a non-linear Finite Element assembly model, the impact of the evolution of grid support under irradiation on the mechanical behavior of the full assembly in terms of axial and

Human Assisted Assembly Processes

Energy Technology Data Exchange (ETDEWEB)

CALTON,TERRI L.; PETERS,RALPH R.

2000-01-01

Automatic assembly sequencing and visualization tools are valuable in determining the best assembly sequences, but without Human Factors and Figure Models (HFFMs) it is difficult to evaluate or visualize human interaction. In industry, accelerating technological advances and shorter market windows have forced companies to turn to an agile manufacturing paradigm. This trend has promoted computerized automation of product design and manufacturing processes, such as automated assembly planning. However, all automated assembly planning software tools assume that the individual components fly into their assembled configuration and generate what appear to be a perfectly valid operations, but in reality the operations cannot physically be carried out by a human. Similarly, human figure modeling algorithms may indicate that assembly operations are not feasible and consequently force design modifications; however, if they had the capability to quickly generate alternative assembly sequences, they might have identified a feasible solution. To solve this problem HFFMs must be integrated with automated assembly planning to allow engineers to verify that assembly operations are possible and to see ways to make the designs even better. Factories will very likely put humans and robots together in cooperative environments to meet the demands for customized products, for purposes including robotic and automated assembly. For robots to work harmoniously within an integrated environment with humans the robots must have cooperative operational skills. For example, in a human only environment, humans may tolerate collisions with one another if they did not cause much pain. This level of tolerance may or may not apply to robot-human environments. Humans expect that robots will be able to operate and navigate in their environments without collisions or interference. The ability to accomplish this is linked to the sensing capabilities available. Current work in the field of cooperative

Textual Enhancement of Input: Issues and Possibilities

Science.gov (United States)

Han, ZhaoHong; Park, Eun Sung; Combs, Charles

2008-01-01

The input enhancement hypothesis proposed by Sharwood Smith (1991, 1993) has stimulated considerable research over the last 15 years. This article reviews the research on textual enhancement of input (TE), an area where the majority of input enhancement studies have aggregated. Methodological idiosyncrasies are the norm of this body of research.…

Self-Assembly of Infinite Structures

Directory of Open Access Journals (Sweden)

Scott M. Summers

2009-06-01

Full Text Available We review some recent results related to the self-assembly of infinite structures in the Tile Assembly Model. These results include impossibility results, as well as novel tile assembly systems in which shapes and patterns that represent various notions of computation self-assemble. Several open questions are also presented and motivated.

Nuclear fuel assembly

International Nuclear Information System (INIS)

Anthony, A.J.

1980-01-01

A bimetallic spacer means is cooperatively associated with a nuclear fuel assembly and operative to resist the occurrence of in-reactor bowing of the nuclear fuel assembly. The bimetallic spacer means in one embodiment of the invention includes a space grid formed, at least principally, of zircaloy to the external surface of which are attached a plurality of stainless steel strips. In another embodiment the strips are attached to fuel pins. In each of the embodiments, the stainless steel strips during power production expand outwardly to a greater extent than do the members to which the stainless steel strips are attached, thereby forming stiff springs which abut against like bimetallic spacer means with which the other nuclear fuel assemblies are provided in a given nuclear reactor core to thus prevent the occurrence of in-reactor bowing of the nuclear fuel assemblies. (author)

Nuclear fuel assembly

International Nuclear Information System (INIS)

Betten, P.R.

1976-01-01

Under the invention the fuel assembly is particularly suitable for liquid metal cooled fast neutron breeder reactors. Hence, according to the invention a fuel assembly cladding includes inward corrugations with respect to the remainder of the cladding according to a recurring pattern determined by the pitch of the metal wire helically wound round the fuel rods of the assembly. The parts of the cladding pressed inwards correspond to the areas in which the wire encircling the peripheral fuel rods is generally located apart from the cladding, thereby reducing the play between the cladding and the peripheral fuel rods situated in these areas. The reduction in the play in turn improves the coolant flow in the internal secondary channels of the fuel assembly to the detriment of the flow in the peripheral secondary channels and thereby establishes a better coolant fluid temperature profile [fr

Method and apparatus for assembling a permanent magnet pole assembly

Science.gov (United States)

Carl, Jr., Ralph James; Bagepalli, Bharat Sampathkumaran [Niskayuna, NY; Jansen, Patrick Lee [Scotia, NY; Dawson, Richard Nils [Voorheesville, NY; Qu, Ronghai [Clifton Park, NY; Avanesov, Mikhail Avramovich [Moscow, RU

2009-08-11

A pole assembly for a rotor, the pole assembly includes a permanent magnet pole including at least one permanent magnet block, a plurality of laminations including a pole cap mechanically coupled to the pole, and a plurality of laminations including a base plate mechanically coupled to the pole.

TPX assembly plan

International Nuclear Information System (INIS)

Knutson, D.

1993-01-01

The TPX machine will be assembled in the TFTR Test Cell at the Plasma Physics Laboratory, utilizing the existing TFTR machine foundation. Preparation of the area for assembly will begin after completion of the decontamination and decommissioning phase on TFTR and certification that the radiation levels remaining, if any, are consistent with the types of operations planned. Assembly operations begin with the arrival of the first components, and conclude, approximately 24 months later, with the successful completion of the integrated systems tests and the achievement of a first plasma

CBrowse: a SAM/BAM-based contig browser for transcriptome assembly visualization and analysis.

Science.gov (United States)

Li, Pei; Ji, Guoli; Dong, Min; Schmidt, Emily; Lenox, Douglas; Chen, Liangliang; Liu, Qi; Liu, Lin; Zhang, Jie; Liang, Chun

2012-09-15

To address the impending need for exploring rapidly increased transcriptomics data generated for non-model organisms, we developed CBrowse, an AJAX-based web browser for visualizing and analyzing transcriptome assemblies and contigs. Designed in a standard three-tier architecture with a data pre-processing pipeline, CBrowse is essentially a Rich Internet Application that offers many seamlessly integrated web interfaces and allows users to navigate, sort, filter, search and visualize data smoothly. The pre-processing pipeline takes the contig sequence file in FASTA format and its relevant SAM/BAM file as the input; detects putative polymorphisms, simple sequence repeats and sequencing errors in contigs and generates image, JSON and database-compatible CSV text files that are directly utilized by different web interfaces. CBowse is a generic visualization and analysis tool that facilitates close examination of assembly quality, genetic polymorphisms, sequence repeats and/or sequencing errors in transcriptome sequencing projects. CBrowse is distributed under the GNU General Public License, available at http://bioinfolab.muohio.edu/CBrowse/ liangc@muohio.edu or liangc.mu@gmail.com; glji@xmu.edu.cn Supplementary data are available at Bioinformatics online.

Assembly Modulated by Particle Position and Shape: A New Concept in Self-Assembly

DEFF Research Database (Denmark)

Tavacoli, Joe W; Heuvingh, Julien; Du Roure, Olivia

2017-01-01

In this communication we outline how the bespoke arrangements and design of micron-sized superparamagnetic shapes provide levers to modulate their assembly under homogeneous magnetic fields. We label this new approach, 'assembly modulated by particle position and shape' (APPS). Specifically, using...... rectangular lattices of superparamagnetic micron-sized cuboids, we construct distinct microstructures by adjusting lattice pitch and angle of array with respect to a magnetic field. Broadly, we find two modes of assembly: (1) immediate 2D jamming of the cuboids as they rotate to align with the applied field...... (rotation-induced jamming) and (2) aggregation via translation after their full alignment (dipole-dipole assembly). The boundary between these two assembly pathways is independent on field strength being solely a function of the cuboid's dimensions, lattice pitch, and array angle with respect to field...

Effect of input compression and input frequency response on music perception in cochlear implant users.

Science.gov (United States)

Halliwell, Emily R; Jones, Linor L; Fraser, Matthew; Lockley, Morag; Hill-Feltham, Penelope; McKay, Colette M

2015-06-01

A study was conducted to determine whether modifications to input compression and input frequency response characteristics can improve music-listening satisfaction in cochlear implant users. Experiment 1 compared three pre-processed versions of music and speech stimuli in a laboratory setting: original, compressed, and flattened frequency response. Music excerpts comprised three music genres (classical, country, and jazz), and a running speech excerpt was compared. Experiment 2 implemented a flattened input frequency response in the speech processor program. In a take-home trial, participants compared unaltered and flattened frequency responses. Ten and twelve adult Nucleus Freedom cochlear implant users participated in Experiments 1 and 2, respectively. Experiment 1 revealed a significant preference for music stimuli with a flattened frequency response compared to both original and compressed stimuli, whereas there was a significant preference for the original (rising) frequency response for speech stimuli. Experiment 2 revealed no significant mean preference for the flattened frequency response, with 9 of 11 subjects preferring the rising frequency response. Input compression did not alter music enjoyment. Comparison of the two experiments indicated that individual frequency response preferences may depend on the genre or familiarity, and particularly whether the music contained lyrics.

Dynamic behaviour of diagnostic assemblies

International Nuclear Information System (INIS)

Pecinka, L.

1980-01-01

The methodology is shown of calculating the frequency spectrum of a diagnostic assembly. The oscillations of the assembly as a whole, of a fuel rod bundle, the assembly jacket and of the individual rods in the bundle were considered. The manufacture is suggested of a model assembly which would be used for testing forced vibrations using an experimental water loop. (M.S.)

Selecting Operations for Assembler Encoding

Directory of Open Access Journals (Sweden)

Tomasz Praczyk

2010-04-01

Full Text Available Assembler Encoding is a neuro-evolutionary method in which a neural network is represented in the form of a simple program called Assembler Encoding Program. The task of the program is to create the so-called Network Definition Matrix which maintains all the information necessary to construct the network. To generate Assembler Encoding Programs and the subsequent neural networks evolutionary techniques are used.
The performance of Assembler Encoding strongly depends on operations used in Assembler Encoding Programs. To select the most effective operations, experiments in the optimization and the predator-prey problem were carried out. In the experiments, Assembler Encoding Programs equipped with different types of operations were tested. The results of the tests are presented at the end of the paper.

Evolution of fuel rod support under irradiation impact on the mechanical behaviour of fuel assemblies

International Nuclear Information System (INIS)

Billerey, Antoine; Waeckel, Nicolas

2005-01-01

New fuel management targets imply to increase fuel assembly discharge burnup. Therefore, the prediction of the mechanical behaviour of the irradiated fuel assembly is essential such as excessive fuel assembly distortion induce incomplete Rod Cluster Control Assembly insertion problems (safety issue) or fuel rod vibration induced wear leading to leaking rods (plant operation problems). Within this framework, one of the most important parameter is the knowledge of the fuel rod support in the grid cell because it directly governs the mechanical behaviour of the fuel assembly and consequently allows to predict the behaviour of irradiated structures in terms of (1) axial and lateral deformation (global behaviour of the assembly) and (2) rod vibration induced wear (local behaviour of the rod). Generally, fuel rod support is provided by a spring-dimple system fixed to the grid. During irradiation, the spring force decreases and a gap between the rod and the spring may occur. This phenomenon is due to (1) stress relieving in the spring and in the dimples, (2) grid growth and (3) reduction of the rod diameter. Two models have been developed to predict the behaviour of the rod in the cell. The first model is dedicated to the evaluation of the spring force relaxation during irradiation. The second one can assess the rotation characteristic of the fuel rod in the cell, function of the spring force. The main input parameters are (1) the creep laws of the grid materials, (2) the growth law of the grid, (3) the evolution of rod diameter and (4) the design of the fuel rod support. The aim of this paper is to: (1) evaluate the consequences of grid support design modifications on the rod vibration sensitivity in terms of predicted rod to grid maximum gap during irradiation and time in operation with an open rod to grid gap, (2) evaluate, using a linear or non-linear Finite Element assembly model, the impact of the evolution of grid support under irradiation on the overall mechanical

Flashback resistant pre-mixer assembly

Science.gov (United States)

Laster, Walter R [Oviedo, FL; Gambacorta, Domenico [Oviedo, FL

2012-02-14

A pre-mixer assembly associated with a fuel supply system for mixing of air and fuel upstream from a main combustion zone in a gas turbine engine. The pre-mixer assembly includes a swirler assembly disposed about a fuel injector of the fuel supply system and a pre-mixer transition member. The swirler assembly includes a forward end defining an air inlet and an opposed aft end. The pre-mixer transition member has a forward end affixed to the aft end of the swirler assembly and an opposed aft end defining an outlet of the pre-mixer assembly. The aft end of the pre-mixer transition member is spaced from a base plate such that a gap is formed between the aft end of the pre-mixer transition member and the base plate for permitting a flow of purge air therethrough to increase a velocity of the air/fuel mixture exiting the pre-mixer assembly.

Nuclear reactor fuel assembly

International Nuclear Information System (INIS)

Sasaki, Y.; Tashima, J.

1975-01-01

A description is given of nuclear reactor fuel assemblies arranged in the form of a lattice wherein there is attached to the interface of one of two adjacent fuel assemblies a plate spring having a concave portion curved toward said interface and to the interface of the other fuel assembly a plate spring having a convex portion curved away from said interface

Directed nucleation assembly of DNA tile complexes for barcode-patterned lattices

Science.gov (United States)

Yan, Hao; Labean, Thomas H.; Feng, Liping; Reif, John H.

2003-07-01

The programmed self-assembly of patterned aperiodic molecular structures is a major challenge in nanotechnology and has numerous potential applications for nanofabrication of complex structures and useful devices. Here we report the construction of an aperiodic patterned DNA lattice (barcode lattice) by a self-assembly process of directed nucleation of DNA tiles around a scaffold DNA strand. The input DNA scaffold strand, constructed by ligation of shorter synthetic oligonucleotides, provides layers of the DNA lattice with barcode patterning information represented by the presence or absence of DNA hairpin loops protruding out of the lattice plane. Self-assembly of multiple DNA tiles around the scaffold strand was shown to result in a patterned lattice containing barcode information of 01101. We have also demonstrated the reprogramming of the system to another patterning. An inverted barcode pattern of 10010 was achieved by modifying the scaffold strands and one of the strands composing each tile. A ribbon lattice, consisting of repetitions of the barcode pattern with expected periodicity, was also constructed by the addition of sticky ends. The patterning of both classes of lattices was clearly observable via atomic force microscopy. These results represent a step toward implementation of a visual readout system capable of converting information encoded on a 1D DNA strand into a 2D form readable by advanced microscopic techniques. A functioning visual output method would not only increase the readout speed of DNA-based computers, but may also find use in other sequence identification techniques such as mutation or allele mapping.

Design of the ITER Tokamak Assembly Tools

International Nuclear Information System (INIS)

Park, Hyunki; Her, Namil; Kim, Byungchul; Im, Kihak; Jung, Kijung; Lee, Jaehyuk; Im, Kisuk

2006-01-01

ITER (International Thermonuclear Experimental Reactor) Procurement allocation among the seven Parties, EU, JA, CN, IN , KO, RF and US had been decided in Dec. 2005. ITER Tokamak assembly tools is one of the nine components allocated to Korea for the construction of the ITER. Assembly tools except measurement and common tools are supplied to assemble the ITER Tokamak and classified into 9 groups according to components to be assembled. Among the 9 groups of assembly tools, large-sized Sector Sub-assembly Tools and Sector Assembly Tools are used at the first stage of ITER Tokamak construction and need to be designed faster than seven other assembly tools. ITER IT (International Team) proposed Korea to accomplish ITA (ITER Transitional Arrangements) Task on detailed design, manufacturing feasibility and contract specification of specific, large sized tools such as Upending Tool, Lifting Tool, Sector Sub-assembly Tool and Sector Assembly Tool in Oct. 2004. Based on the concept design by ITER IT, Korea carried out ITA Task on detailed design of large-sized and specific Sector Sub-assembly and Sector Assembly Tools until Mar. 2006. The Sector Sub-assembly Tools mainly consist of the Upending, Lifting, Vacuum Vessel Support and Bracing, and Sector Sub-assembly Tool, among which the design of three tools are herein. The Sector Assembly Tools mainly consist of the Toroidal Field (TF) Gravity Support Assembly, Sector In-pit Assembly, TF Coil Assembly, Vacuum Vessel (VV) Welding and Vacuum Vessel Thermal Shield (TS) Assembly Tool, among which the design of Sector In-pit Assembly Tool is described herein

Judgement on the data for fuel assembly outlet temperatures of WWER fuel assemblies in power reactors based on measurements with experimental fuel assemblies

International Nuclear Information System (INIS)

Krause, F.

1986-01-01

In the period from 1980 to 1985, in the Rheinsberg nuclear power plant experimental fuel assemblies were used on lattices at the periphery of the core. These particular fuel assemblies dispose of an extensive in-core instrumentation with different sensors. Besides this, they are fit out with a device to systematically thottle the coolant flow. The large power gradient present at the core position of the experimental fuel assembly causes a temperature profile along the fuel assemblies which is well provable at the measuring points of the outlet temperature. Along the direction of flow this temperature profile in the coolant degrades only slowly. This effect is to be taken into account when measuring the fuel assembly outlet temperature of WWER fuel assemblies. Besides this, the results of the measurements hinted both at a γ-heating of the temperature measuring points and at tolerances in the calculation of the micro power density distribution. (author)

Selection method and device for reactor core performance calculation input indication

International Nuclear Information System (INIS)

Yuto, Yoshihiro.

1994-01-01

The position of a reactor core component on a reactor core map, which is previously designated and optionally changeable, is displayed by different colors on a CRT screen by using data of a data file incorporating results of a calculation for reactor core performance, such as incore thermal limit values. That is, an operator specifies the kind of the incore component to be sampled on a menu screen, to display the position of the incore component which satisfies a predetermined condition on the CRT screen by different colors in the form of a reactor core map. The position for the reactor core component displayed on the CRT screen by different colors is selected and designated on the screen by a touch panel, a mouse or a light pen, thereby automatically outputting detailed data of evaluation for the reactor core performance of the reactor core component at the indicated position. Retrieval of coordinates of fuel assemblies to be data sampled and input of the coordinates and demand for data sampling can be conducted at once by one menu screen. (N.H.)

Fuel assemblies

International Nuclear Information System (INIS)

Nagano, Mamoru; Yoshioka, Ritsuo

1983-01-01

Purpose: To effectively utilize nuclear fuels by increasing the reactivity of a fuel assembly and reduce the concentration at the central region thereof upon completion of the burning. Constitution: A fuel assembly is bisected into a central region and a peripheral region by disposing an inner channel box within a channel box. The flow rate of coolants passing through the central region is made greater than that in the peripheral region. The concentration of uranium 235 of the fuel rods in the central region is made higher. In such a structure, since the moderating effect in the central region is improved, the reactivity of the fuel assembly is increased and the uranium concentration in the central region upon completion of the burning can be reduced, fuel economy and effective utilization of uranium can be attained. (Kamimura, M.)

Fuel assembly

International Nuclear Information System (INIS)

Nakatsuka, Masafumi; Matsuzuka, Ryuji.

1976-01-01

Object: To provide a fuel assembly which can decrease pressure loss of coolant to uniform temperature. Structure: A sectional area of a flow passage in the vicinity of an inner peripheral surface of a wrapper tube is limited over the entire length to prevent the temperature of a fuel element in the outermost peripheral portion from being excessively decreased to thereby flatten temperature distribution. To this end, a plurality of pincture-frame-like sheet metals constituting a spacer for supporting a fuel assembly, which has a plurality of fuel elements planted lengthwise and in given spaced relation within the wrapper tube, is disposed in longitudinal grooves and in stacked fashion to form a substantially honeycomb-like space in cross section. The fuel elements are inserted and supported in the space to form a fuel assembly. (Kamimura, M.)

Welding facilities for NPP assembling

International Nuclear Information System (INIS)

Rojtenberg, S.S.

1987-01-01

Recommendations concerning the choice of equipment for welding in pre-assembling work shops, in the enlarging assembling shops and at the assembling site, are given. Advanced production automatic welders and semiautomatic machines, applied during the NPP equipment assembling as well as automatic machines specially produced for welding the main reactor components and pipelines are described. Automatic and semiautomatic machine and manual welding post supply sources are considered

Delay selection by spike-timing-dependent plasticity in recurrent networks of spiking neurons receiving oscillatory inputs.

Directory of Open Access Journals (Sweden)

Robert R Kerr

Full Text Available Learning rules, such as spike-timing-dependent plasticity (STDP, change the structure of networks of neurons based on the firing activity. A network level understanding of these mechanisms can help infer how the brain learns patterns and processes information. Previous studies have shown that STDP selectively potentiates feed-forward connections that have specific axonal delays, and that this underlies behavioral functions such as sound localization in the auditory brainstem of the barn owl. In this study, we investigate how STDP leads to the selective potentiation of recurrent connections with different axonal and dendritic delays during oscillatory activity. We develop analytical models of learning with additive STDP in recurrent networks driven by oscillatory inputs, and support the results using simulations with leaky integrate-and-fire neurons. Our results show selective potentiation of connections with specific axonal delays, which depended on the input frequency. In addition, we demonstrate how this can lead to a network becoming selective in the amplitude of its oscillatory response to this frequency. We extend this model of axonal delay selection within a single recurrent network in two ways. First, we show the selective potentiation of connections with a range of both axonal and dendritic delays. Second, we show axonal delay selection between multiple groups receiving out-of-phase, oscillatory inputs. We discuss the application of these models to the formation and activation of neuronal ensembles or cell assemblies in the cortex, and also to missing fundamental pitch perception in the auditory brainstem.

Composite turbine bucket assembly

Science.gov (United States)

Liotta, Gary Charles; Garcia-Crespo, Andres

2014-05-20

A composite turbine blade assembly includes a ceramic blade including an airfoil portion, a shank portion and an attachment portion; and a transition assembly adapted to attach the ceramic blade to a turbine disk or rotor, the transition assembly including first and second transition components clamped together, trapping said ceramic airfoil therebetween. Interior surfaces of the first and second transition portions are formed to mate with the shank portion and the attachment portion of the ceramic blade, and exterior surfaces of said first and second transition components are formed to include an attachment feature enabling the transition assembly to be attached to the turbine rotor or disk.

Stochastic weather inputs for improved urban water demand forecasting: application of nonlinear input variable selection and machine learning methods

Science.gov (United States)

Quilty, J.; Adamowski, J. F.

2015-12-01

Urban water supply systems are often stressed during seasonal outdoor water use as water demands related to the climate are variable in nature making it difficult to optimize the operation of the water supply system. Urban water demand forecasts (UWD) failing to include meteorological conditions as inputs to the forecast model may produce poor forecasts as they cannot account for the increase/decrease in demand related to meteorological conditions. Meteorological records stochastically simulated into the future can be used as inputs to data-driven UWD forecasts generally resulting in improved forecast accuracy. This study aims to produce data-driven UWD forecasts for two different Canadian water utilities (Montreal and Victoria) using machine learning methods by first selecting historical UWD and meteorological records derived from a stochastic weather generator using nonlinear input variable selection. The nonlinear input variable selection methods considered in this work are derived from the concept of conditional mutual information, a nonlinear dependency measure based on (multivariate) probability density functions and accounts for relevancy, conditional relevancy, and redundancy from a potential set of input variables. The results of our study indicate that stochastic weather inputs can improve UWD forecast accuracy for the two sites considered in this work. Nonlinear input variable selection is suggested as a means to identify which meteorological conditions should be utilized in the forecast.

TOOL ASSEMBLY WITH BI-DIRECTIONAL BEARING