Analysis and Improvement of Control Algorithm for Operation Mode Transition due to Input Channel Trouble in Control Systems

Energy Technology Data Exchange (ETDEWEB)

Ahn, Myunghoon; Kim, Woogoon; Yim, Hyeongsoon [KEPCO Engineering and Construction Co., Deajeon (Korea, Republic of)

2016-10-15

The PI (Proportional plus Integral) controller, which is the essential functional block in control systems, can automatically perform the stable control of an important plant process while reducing the steady state error and improving the transient response. However, if the received input PV (Process Variable) is not normal due to input channel trouble, it will be difficult to control the system automatically. For this reason, many control systems are implemented to change the operation mode from automatic to manual mode in the PI controller when the failed input PV is detected. If the PI controller is in automatic mode for all the time, the control signal varies as the change of the input PV is continuously reflected in the control algorithm. In the other cases, since the controller changes into the manual mode at t=0, the control signal is fixed at the last PI controller output and thus the feedback control is not performed anymore until the operator takes an action such as the operation mode change. As a result of analysis and simulations for the controller’s operation modes in all the cases of input channel trouble, we discovered that it is more appropriate to maintain the automatic mode despite the bad quality in the PV. Therefore, we improved the control system algorithm reflecting the analysis results for the operator’s convenience and the stability of a control system.

Development of transportation operations requirements

International Nuclear Information System (INIS)

Grady, S.T.; Best, R.E.; Danese, F.L.; Peterson, R.W.; Pope, R.B.

1990-01-01

Transport conditions at various utility sties vary dramatically in terms of characteristics at and near the site, requirements, administrative procedures, and other factors. Continuation of design efforts for the OCRWM transportation operations system requires that the operating requirements for the transportation system -- quantity of fuel per unit time per site -- be identified so that the effect the variations have on the system can be accommodated. The approach outlined in this paper provides for an identification of specific sites, evaluation of shipment capabilities at each site, and integration of the sites into multi-site shipping campaigns to scope the logistics management problem for the transportation operations system. 1 fig., 1 tab

A representation result for hysteresis operators with vector valued inputs and its application to models for magnetic materials

Energy Technology Data Exchange (ETDEWEB)

Klein, Olaf, E-mail: Olaf.Klein@wias-berlin.de

2014-02-15

In this work, hysteresis operators mapping continuous vector-valued input functions being piecewise monotaffine, i.e. being piecewise the composition of a monotone with an affine function, to vector-valued output functions are considered. It is shown that the operator can be generated by a unique defined function on the convexity triple free strings. A formulation of a congruence property for periodic inputs is presented and reformulated as a condition for the generating string function.

Incinerator performance: effects of changes in waste input and furnace operation on air emissions and residues

DEFF Research Database (Denmark)

Astrup, Thomas; Riber, Christian; Pedersen, Anne Juul

2011-01-01

Waste incineration can be considered a robust technology for energy recovery from mixed waste. Modern incinerators are generally able to maintain relatively stable performance, but changes in waste input and furnace operation may affect emissions. This study investigated how inorganic air emissions...... including ‘as-large-as-possible’ changes in furnace operation (oxygen levels, air supply and burnout level) only using normal MSW as input. The experiments showed that effects from the added waste materials were significant in relation to: air emissions (in particular As, Cd, Cr, Hg, Sb), element transfer...... coefficients, and residue composition (As, Cd, Cl, Cr, Cu, Hg, Mo, Ni, Pb, S, Sb, Zn). Changes in furnace operation could not be directly linked to changes in emissions and residues. The results outlined important elements in waste which should be addressed in relation to waste incinerator performance. Likely...

Cumulative input/output balance of a mechanical-biological waste treatment plant. Comparison of construction material requirements, operating energy expenditure, and the requirement of auxiliary materials in comparison with waste combustion; Kumulative Bilanzierung der mechanisch-biologischen Restabfallbehandlung - Baumaterialien und betrieblicher Energie- und Hilfsstoffaufwand im Vergleich zur Muellverbrennung

Energy Technology Data Exchange (ETDEWEB)

Wallmann, R.; Fricke, K. [Ingenieurgemeinschaft Witzenhausen (Germany); Vogtmann, H. [Hessisches Landesamt fuer Regionalentwicklung und Landwirtschaft, Kassel (Germany)

1998-12-31

The study strikes a cumulative input/output balance of an existing waste conditioning plant considering not only operating energy demand but also the required construction materials for erecting the plant. In operation since 1996, the waste conditioning plant is entirely state of the art; hence the data obtained are up to date. The results are compared with relevant results for a waste processing plant and evaluated. (orig.) [Deutsch] Im Rahmen der vorliegenden Untersuchung erfolgt eine kumulative Bilanzierung einer bestehenden MBA-Anlage, wobei neben den betrieblichen Energieaufwendungen auch die Baumaterialien zur Herstellung der Anlage beruecksichtigt werden. Die seit 1996 in Betrieb befindliche Abfallbehandlungsanlage entspricht weitestgehend dem Stand der Technik der MBA, wodurch die Aktualitaet der Daten gegeben ist. Die Ergebnisse der Bilanzierung werden im Vergleich zu einer MVA dargestellt und bewertet. (orig.)

Substantial reductions of input energy and peak power requirements in targets for heavy ion fusion

International Nuclear Information System (INIS)

Mark, J.W.K.; Pan, Y.L.

1986-01-01

Two ways of reducing the requirements of the heavy ion driver for inertial confinement fusion (ICF) target implosion are described. Compared to estimates of target gain not using these methods, the target input energy and peak power may be reduced by about a factor of two with the use of the hybrid-implosion concept. Another factor of two reduction in input energy may be obtained with the use of spin-polarized DT fuel in the ICF target

Developing an operational rangeland water requirement satisfaction index

Science.gov (United States)

Senay, Gabriel B.; Verdin, James P.; Rowland, James

2011-01-01

Developing an operational water requirement satisfaction index (WRSI) for rangeland monitoring is an important goal of the famine early warning systems network. An operational WRSI has been developed for crop monitoring, but until recently a comparable WRSI for rangeland was not successful because of the extremely poor performance of the index when based on published crop coefficients (K c) for rangelands. To improve the rangeland WRSI, we developed a simple calibration technique that adjusts the K c values for rangeland monitoring using long-term rainfall distribution and reference evapotranspiration data. The premise for adjusting the K c values is based on the assumption that a viable rangeland should exhibit above-average WRSI (values >80%) during a normal year. The normal year was represented by a median dekadal rainfall distribution (satellite rainfall estimate from 1996 to 2006). Similarly, a long-term average for potential evapotranspiration was used as input to the famine early warning systems network WRSI model in combination with soil-water-holding capacity data. A dekadal rangeland WRSI has been operational for east and west Africa since 2005. User feedback has been encouraging, especially with regard to the end-of-season WRSI anomaly products that compare the index's performance to ‘normal’ years. Currently, rangeland WRSI products are generated on a dekadal basis and posted for free distribution on the US Geological Survey early warning website at http://earlywarning.usgs.gov/adds/

Designing of all optical generalized circuit for two-input binary and multi-valued logical operations

Science.gov (United States)

Bhowmik, Panchatapa; Roy, Jitendra Nath; Chattopadhyay, Tanay

2014-11-01

This paper presents a generalized all optical circuit of two-input logical operation (both binary and multi-valued), using an optical nonlinear material (OPNLM) based switch. The inputs of the logic gates are represented by different polarization states of light. This model is simple, practical and very much useful for future all optical information processing. Proposed scheme can work for different wavelengths and for different materials. The simulation result with the nonlinear material gold nanoparticle embedded in optically transparent matrices alumina (Al2O3) is also presented in the paper.

Droplet size characteristics and energy input requirements of emulsions formed using high-intensity-pulsed electric fields

International Nuclear Information System (INIS)

Scott, T.C.; Sisson, W.G.

1987-01-01

Experimental methods have been developed to measure droplet size characteristics and energy inputs associated with the rupture of aqueous droplets by high-intensity-pulsed electric fields. The combination of in situ microscope optics and high-speed video cameras allows reliable observation of liquid droplets down to 0.5 μm in size. Videotapes of electric-field-created emulsions reveal that average droplet sizes of less than 5 μm are easily obtained in such systems. Analysis of the energy inputs into the fluids indicates that the electric field method requires less than 1% of the energy required from mechanical agitation to create comparable droplet sizes. 11 refs., 3 figs., 2 tabs

New tools for C.A.D. of input devices for tele-operation with force feedback

International Nuclear Information System (INIS)

Gosselin, F.

2000-01-01

The performances of a tele-operation system are related to the master arm's ability to emulate the behavior of the remote environment. Ideally, it allows the operator to control the slave arm in a natural way as if that were an extension of its own body. The criteria to be checked for that are known but contradictory. It is thus necessary to make trade-offs on which there is not consensus. Existing input devices are therefore very varied thus more or less adapted to the tasks considered, which is in general checked a posteriori. In this document, we propose an original approach allowing to dimension the master arm a priori according to the use which one wishes to make. For that, we developed two tools: - the first one makes it possible to establish his specifications by taking account of the transmission of information between the operator and the slave arm. By exploiting their respective limitations, one is assured that the master arm will not limit the performances of the system, - the second one allows to design it (kinematics, size, motorization... ) according to the preceding specifications. For that, we use well-known theoretical tools which however are approached here as design tools. This leads to the definition of new concepts which do not appear in the literature. This approach is used to establish the specifications of a master arm for nuclear and offshore tele-operation then to design two input devices answering these specifications. The first has 3 degrees of freedom with force feedback. Its performances are higher than those of the best existing input devices. The second is a mock-up of a 6 degrees of freedom master arm. It uses a new parallel structure that is redundant in actuation and whose performances are remarkable. (author) [fr

10 CFR 490.306 - Vehicle operation requirements.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Vehicle operation requirements. 490.306 Section 490.306... Provider Vehicle Acquisition Mandate § 490.306 Vehicle operation requirements. The alternative fueled vehicles acquired pursuant to section 490.302 of this part shall be operated solely on alternative fuels...

The energy input in the construction and operation of nuclear power stations

International Nuclear Information System (INIS)

Kolb, G.; Niehaus, F.; Rath-Nagel, S.; Voss, A.

1975-08-01

The production of electric energy requires energy investments not only for direct fuel input but for the construction of power plants and for the extraction of primary energy fuels as well. When the overall energy balance of energy converting systems has to be assessed these energetic investments must be included. In the present investigation the overall energy input of different nuclear power plant types (comprising the nuclear fuel cycle) is computed and compared with a coal-fired plant. Moreover a time-dependent energy balance for the expansion of nuclear capacity according to the existing nuclear programs is calculated. Even applying only Light Water Reactors the nuclear expansion program (with an installed capacity of 50 GWsub(el) in 1985 and 170 GWsub(el) in 2000) would result in an accumulated fossil fuel saving of approximately the tenfold amount of primary energy consumed in the Federal Republic of Germany yearly today. (orig.) [de

Requirements to be met by the operation manual

International Nuclear Information System (INIS)

1981-03-01

The rule applies to the contents and the lay-out of the operating manual for stationary nuclear power plants. The draft contains: 1. General requirement to be met by the contents of the operating manual. The operating manual to be arranged in 4 parts (part 1: internal rules and regulations; part 2: operation overall plant; part 3: incidents; part 4: operation systems). Safety specifications to be included in the manual, the exemption being the system of technical documentation. 2. General requirements to be met by the lay-out of the operating manual. Comprehensibility; legibility; structure and subdivisions; arrangement of the instructions and design of the manuals cover. 3. Requirements to be met by part 1. Defining the various internal rules and regulations (personnel management); rules and regulations concerning inspections and shift work; maintenance and repair; radiation protection; guard duty and admission; alarm; fire protection; first aid. 4. Requirements to be met by part 2. Provisions and operational limitations; limit values important from the point of view of safety; normal operation; anomalous operation; in-service inspections. 6. Requirements to be met by part 3. 7. Annex: Rules, regulations and stipulations mentioned in the rule draft. (orig.)

A circuit design for multi-inputs stateful OR gate

Energy Technology Data Exchange (ETDEWEB)

Chen, Qiao; Wang, Xiaoping, E-mail: wangxiaoping@hust.edu.cn; Wan, Haibo; Yang, Ran; Zheng, Jian

2016-09-07

The in situ logic operation on memristor memory has attracted researchers' attention. In this brief, a new circuit structure that performs a stateful OR logic operation is proposed. When our OR logic is operated in series with other logic operations (IMP, AND), only two voltages should to be changed while three voltages are necessary in the previous one-step OR logic operation. In addition, this circuit structure can be extended to multi-inputs OR operation to perfect the family of logic operations on memristive memory in nanocrossbar based networks. The proposed OR gate can enable fast logic operation, reduce the number of required memristors and the sequential steps. Through analysis and simulation, the feasibility of OR operation is demonstrated and the appropriate parameters are obtained.

A circuit design for multi-inputs stateful OR gate

International Nuclear Information System (INIS)

Chen, Qiao; Wang, Xiaoping; Wan, Haibo; Yang, Ran; Zheng, Jian

2016-01-01

The in situ logic operation on memristor memory has attracted researchers' attention. In this brief, a new circuit structure that performs a stateful OR logic operation is proposed. When our OR logic is operated in series with other logic operations (IMP, AND), only two voltages should to be changed while three voltages are necessary in the previous one-step OR logic operation. In addition, this circuit structure can be extended to multi-inputs OR operation to perfect the family of logic operations on memristive memory in nanocrossbar based networks. The proposed OR gate can enable fast logic operation, reduce the number of required memristors and the sequential steps. Through analysis and simulation, the feasibility of OR operation is demonstrated and the appropriate parameters are obtained.

A Development of a System Enables Character Input and PC Operation via Voice for a Physically Disabled Person with a Speech Impediment

Science.gov (United States)

Tanioka, Toshimasa; Egashira, Hiroyuki; Takata, Mayumi; Okazaki, Yasuhisa; Watanabe, Kenzi; Kondo, Hiroki

We have designed and implemented a PC operation support system for a physically disabled person with a speech impediment via voice. Voice operation is an effective method for a physically disabled person with involuntary movement of the limbs and the head. We have applied a commercial speech recognition engine to develop our system for practical purposes. Adoption of a commercial engine reduces development cost and will contribute to make our system useful to another speech impediment people. We have customized commercial speech recognition engine so that it can recognize the utterance of a person with a speech impediment. We have restricted the words that the recognition engine recognizes and separated a target words from similar words in pronunciation to avoid misrecognition. Huge number of words registered in commercial speech recognition engines cause frequent misrecognition for speech impediments' utterance, because their utterance is not clear and unstable. We have solved this problem by narrowing the choice of input down in a small number and also by registering their ambiguous pronunciations in addition to the original ones. To realize all character inputs and all PC operation with a small number of words, we have designed multiple input modes with categorized dictionaries and have introduced two-step input in each mode except numeral input to enable correct operation with small number of words. The system we have developed is in practical level. The first author of this paper is physically disabled with a speech impediment. He has been able not only character input into PC but also to operate Windows system smoothly by using this system. He uses this system in his daily life. This paper is written by him with this system. At present, the speech recognition is customized to him. It is, however, possible to customize for other users by changing words and registering new pronunciation according to each user's utterance.

Monitoring the inputs required to extend and sustain hygiene promotion: findings from the GLAAS 2013/2014 survey.

Science.gov (United States)

Moreland, Leslie D; Gore, Fiona M; Andre, Nathalie; Cairncross, Sandy; Ensink, Jeroen H J

2016-08-01

There are significant gaps in information about the inputs required to effectively extend and sustain hygiene promotion activities to improve people's health outcomes through water, sanitation and hygiene (WASH) interventions. We sought to analyse current country and global trends in the use of key inputs required for effective and sustainable implementation of hygiene promotion to help guide hygiene promotion policy and decision-making after 2015. Data collected in response to the GLAAS 2013/2014 survey from 93 countries of 94 were included, and responses were analysed for 12 questions assessing the inputs and enabling environment for hygiene promotion under four thematic areas. Data were included and analysed from 20 External Support Agencies (ESA) of 23 collected through self-administered surveys. Firstly, the data showed a large variation in the way in which hygiene promotion is defined and what constitutes key activities in this area. Secondly, challenges to implement hygiene promotion are considerable: include poor implementation of policies and plans, weak coordination mechanisms, human resource limitations and a lack of available hygiene promotion budget data. Despite the proven benefits of hand washing with soap, a critical hygiene-related factor in minimising infection, GLAAS 2013/2014 survey data showed that hygiene promotion remains a neglected component of WASH. Additional research to identify the context-specific strategies and inputs required to enhance the effectiveness of hygiene promotion at scale are needed. Improved data collection methods are also necessary to advance the availability and reliability of hygiene-specific information. © 2016 John Wiley & Sons Ltd.

Input-output supervisor

International Nuclear Information System (INIS)

Dupuy, R.

1970-01-01

The input-output supervisor is the program which monitors the flow of informations between core storage and peripheral equipments of a computer. This work is composed of three parts: 1 - Study of a generalized input-output supervisor. With sample modifications it looks like most of input-output supervisors which are running now on computers. 2 - Application of this theory on a magnetic drum. 3 - Hardware requirement for time-sharing. (author) [fr

Input and execution

International Nuclear Information System (INIS)

Carr, S.; Lane, G.; Rowling, G.

1986-11-01

This document describes the input procedures, input data files and operating instructions for the SYVAC A/C 1.03 computer program. SYVAC A/C 1.03 simulates the groundwater mediated movement of radionuclides from underground facilities for the disposal of low and intermediate level wastes to the accessible environment, and provides an estimate of the subsequent radiological risk to man. (author)

Nursing home staffing requirements and input substitution: effects on housekeeping, food service, and activities staff.

Science.gov (United States)

Bowblis, John R; Hyer, Kathryn

2013-08-01

To study the effect of minimum nurse staffing requirements on the subsequent employment of nursing home support staff. Nursing home data from the Online Survey Certification and Reporting (OSCAR) System merged with state nurse staffing requirements. Facility-level housekeeping, food service, and activities staff levels are regressed on nurse staffing requirements and other controls using fixed effect panel regression. OSCAR surveys from 1999 to 2004. Increases in state direct care and licensed nurse staffing requirements are associated with decreases in the staffing levels of all types of support staff. Increased nursing home nurse staffing requirements lead to input substitution in the form of reduced support staffing levels. © Health Research and Educational Trust.

Updated requirements for control room annunciation: an operations perspective

International Nuclear Information System (INIS)

Davey, E.; Lane, L.

2001-01-01

The purpose of this paper is to describe the results of updating and aligning requirements for annunciation functionality and performance with current expectations for operational excellence. This redefinition of annunciation requirements was undertaken as one component of a project to characterize improvement priorities, establish the operational and economic basis for improvement, and identify preferred implementation options for Ontario Power Generation plants. The updated requirements express the kinds of information support annunciation should provide to Operations staff to support the detection, recognition and response to changes in plant conditions. The updated requirements were developed using several types of information: management and industry expectations for operations excellence, previous definitions of user needs for annunciation, and operational and ergonomic principles. Operations and engineering staff at several stations have helped refine and complete the initial requirements definition. Application of these updated requirements is expected to lead to more effective and task relevant annunciation system improvements that better serve plant operation needs. The paper outlines the project rationale, reviews development objectives, discusses the approaches applied for requirements definition and organization, describes key requirements findings in relation to current operations experience, and discusses the proposed application of these requirements for guiding future annunciation system improvements. (author)

33 CFR 161.12 - Vessel operating requirements.

Science.gov (United States)

2010-07-01

....0′ N. extending eastward through the Golden Gate, and the navigable waters of San Francisco Bay and... safety beyond that provided by other means. The bridge-to-bridge navigational frequency, 156.650 MHz (Ch... Measures, and Operating Requirements § 161.12 Vessel operating requirements. (a) Subject to the exigencies...

30 CFR 784.11 - Operation plan: General requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Operation plan: General requirements. 784.11... PLAN § 784.11 Operation plan: General requirements. Each application shall contain a description of the... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER...

30 CFR 780.11 - Operation plan: General requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Operation plan: General requirements. 780.11... PLAN § 780.11 Operation plan: General requirements. Each application shall contain a description of the... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER...

Equipment Operational Requirements

Energy Technology Data Exchange (ETDEWEB)

Greenwalt, B; Henderer, B; Hibbard, W; Mercer, M

2009-06-11

The Iraq Department of Border Enforcement is rich in personnel, but poor in equipment. An effective border control system must include detection, discrimination, decision, tracking and interdiction, capture, identification, and disposition. An equipment solution that addresses only a part of this will not succeed, likewise equipment by itself is not the answer without considering the personnel and how they would employ the equipment. The solution should take advantage of the existing in-place system and address all of the critical functions. The solutions are envisioned as being implemented in a phased manner, where Solution 1 is followed by Solution 2 and eventually by Solution 3. This allows adequate time for training and gaining operational experience for successively more complex equipment. Detailed descriptions of the components follow the solution descriptions. Solution 1 - This solution is based on changes to CONOPs, and does not have a technology component. It consists of observers at the forts and annexes, forward patrols along the swamp edge, in depth patrols approximately 10 kilometers inland from the swamp, and checkpoints on major roads. Solution 2 - This solution adds a ground sensor array to the Solution 1 system. Solution 3 - This solution is based around installing a radar/video camera system on each fort. It employs the CONOPS from Solution 1, but uses minimal ground sensors deployed only in areas with poor radar/video camera coverage (such as canals and streams shielded by vegetation), or by roads covered by radar but outside the range of the radar associated cameras. This document provides broad operational requirements for major equipment components along with sufficient operational details to allow the technical community to identify potential hardware candidates. Continuing analysis will develop quantities required and more detailed tactics, techniques, and procedures.

21 CFR 111.127 - What quality control operations are required for packaging and labeling operations?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for... and Process Control System: Requirements for Quality Control § 111.127 What quality control operations are required for packaging and labeling operations? Quality control operations for packaging and...

ModSAF-based development of operational requirements for light armored vehicles

Science.gov (United States)

Rapanotti, John; Palmarini, Marc

2003-09-01

Light Armoured Vehicles (LAVs) are being developed to meet the modern requirements of rapid deployment and operations other than war. To achieve these requirements, passive armour is minimized and survivability depends more on sensors, computers, countermeasures and communications to detect and avoid threats. The performance, reliability, and ultimately the cost of these systems, will be determined by the technology trends and the rates at which they mature. Defining vehicle requirements will depend upon an accurate assessment of these trends over a longer term than was previously needed. Modelling and simulation are being developed to study these long-term trends and how they contribute to establishing vehicle requirements. ModSAF is being developed for research and development, in addition to the original requirement of Simulation and Modelling for Acquisition, Rehearsal, Requirements and Training (SMARRT), and is becoming useful as a means for transferring technology to other users, researchers and contractors. This procedure eliminates the need to construct ad hoc models and databases. The integration of various technologies into a Defensive Aids Suite (DAS) can be designed and analyzed by combining field trials and laboratory data with modelling and simulation. ModSAF (Modular Semi-Automated Forces,) is used to construct the virtual battlefield and, through scripted input files, a "fixed battle" approach is used to define and implement contributions from three different sources. These contributions include: models of technology and natural phenomena from scientists and engineers, tactics and doctrine from the military and detailed analyses from operations research. This approach ensures the modelling of processes known to be important regardless of the level of information available about the system. Survivability of DAS-equipped vehicles based on future and foreign technology can be investigated by ModSAF and assessed relative to a test vehicle. A vehicle can

Development a computer codes to couple PWR-GALE output and PC-CREAM input

Science.gov (United States)

Kuntjoro, S.; Budi Setiawan, M.; Nursinta Adi, W.; Deswandri; Sunaryo, G. R.

2018-02-01

Radionuclide dispersion analysis is part of an important reactor safety analysis. From the analysis it can be obtained the amount of doses received by radiation workers and communities around nuclear reactor. The radionuclide dispersion analysis under normal operating conditions is carried out using the PC-CREAM code, and it requires input data such as source term and population distribution. Input data is derived from the output of another program that is PWR-GALE and written Population Distribution data in certain format. Compiling inputs for PC-CREAM programs manually requires high accuracy, as it involves large amounts of data in certain formats and often errors in compiling inputs manually. To minimize errors in input generation, than it is make coupling program for PWR-GALE and PC-CREAM programs and a program for writing population distribution according to the PC-CREAM input format. This work was conducted to create the coupling programming between PWR-GALE output and PC-CREAM input and programming to written population data in the required formats. Programming is done by using Python programming language which has advantages of multiplatform, object-oriented and interactive. The result of this work is software for coupling data of source term and written population distribution data. So that input to PC-CREAM program can be done easily and avoid formatting errors. Programming sourceterm coupling program PWR-GALE and PC-CREAM is completed, so that the creation of PC-CREAM inputs in souceterm and distribution data can be done easily and according to the desired format.

12 CFR 932.6 - Operations risk capital requirement.

Science.gov (United States)

2010-01-01

... operations risk capital requirement shall at all times equal 30 percent of the sum of the Bank's credit risk... percent but no less than 10 percent of the sum of the Bank's credit risk capital requirement and market... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Operations risk capital requirement. 932.6...

Requirements by the operator of supporting systems

International Nuclear Information System (INIS)

Grimm, E.; Lot, L.

1996-01-01

Requirements by the nuclear power station operator on computer support orient themselves to the various operating situations which can arise in the plant. Event-oriented or system-oriented methods of handling determine the type of support by the computer. Pure plant information in situations with few events, an intelligent alarm system in situations with many events and a guide by means of pre-prepared procedures are an aspect of the operator requirements of computer solutions. These are the themes dealt with in this paper. A further theme is the support of the operator by the ergonomics of the control room in the areas of working place, lighting, air conditioning and acoustics. (author) 4 figs

ColloInputGenerator

DEFF Research Database (Denmark)

2013-01-01

This is a very simple program to help you put together input files for use in Gries' (2007) R-based collostruction analysis program. It basically puts together a text file with a frequency list of lexemes in the construction and inserts a column where you can add the corpus frequencies. It requires...... it as input for basic collexeme collostructional analysis (Stefanowitsch & Gries 2003) in Gries' (2007) program. ColloInputGenerator is, in its current state, based on programming commands introduced in Gries (2009). Projected updates: Generation of complete work-ready frequency lists....

Planning and Estimation of Operations Support Requirements

Science.gov (United States)

Newhouse, Marilyn E.; Barley, Bryan; Bacskay, Allen; Clardy, Dennon

2010-01-01

Life Cycle Cost (LCC) estimates during the proposal and early design phases, as well as project replans during the development phase, are heavily focused on hardware development schedules and costs. Operations (phase E) costs are typically small compared to the spacecraft development and test costs. This, combined with the long lead time for realizing operations costs, can lead to de-emphasizing estimation of operations support requirements during proposal, early design, and replan cost exercises. The Discovery and New Frontiers (D&NF) programs comprise small, cost-capped missions supporting scientific exploration of the solar system. Any LCC growth can directly impact the programs' ability to fund new missions, and even moderate yearly underestimates of the operations costs can present significant LCC impacts for deep space missions with long operational durations. The National Aeronautics and Space Administration (NASA) D&NF Program Office at Marshall Space Flight Center (MSFC) recently studied cost overruns and schedule delays for 5 missions. The goal was to identify the underlying causes for the overruns and delays, and to develop practical mitigations to assist the D&NF projects in identifying potential risks and controlling the associated impacts to proposed mission costs and schedules. The study found that 4 out of the 5 missions studied had significant overruns at or after launch due to underestimation of the complexity and supporting requirements for operations activities; the fifth mission had not launched at the time of the mission. The drivers behind these overruns include overly optimistic assumptions regarding the savings resulting from the use of heritage technology, late development of operations requirements, inadequate planning for sustaining engineering and the special requirements of long duration missions (e.g., knowledge retention and hardware/software refresh), and delayed completion of ground system development work. This paper updates the D

RELAP5/MOD3 code manual: User's guide and input requirements. Volume 2

International Nuclear Information System (INIS)

1995-08-01

The RELAP5 code has been developed for best estimate transient simulation of light water reactor coolant systems during postulated accidents. The code models the coupled behavior of the reactor coolant system and the core for loss-of-coolant accidents, and operational transients, such as anticipated transient without scram, loss of offsite power, loss of feedwater, and loss of flow. A generic modeling approach is used that permits simulating a variety of thermal hydraulic systems. Control system and secondary system components are included to permit modeling of plant controls, turbines, condensers, and secondary feedwater systems. Volume II contains detailed instructions for code application and input data preparation

Fuel management for TRIGA reactor operators

International Nuclear Information System (INIS)

Totenbier, R.E.; Levine, S.H.

1980-01-01

One responsibility of the Supervisor of Reactor Operations is to follow the TRIGA core depletion and recommend core loading changes for refueling and special experiments. Calculations required to analyze such changes normally use digital computers and are extremely difficult to perform for one who is not familiar with computer language and nuclear reactor diffusion theory codes. The TRICOM/SCRAM program developed to perform such calculations for the Penn State TRIGA Breazeale Reactor (PSBR), has a very simple input format and is one which can be used by persons having no knowledge of computer codes. The person running the program need not understand computer language such as Fortran, but should be familiar with reactor core geometry and effects of loading changes. To further simplify the input requirements but still allow for all of the studies normally needed by the reactor operations supervisor, the options required for input have been isolated to two. Given a master deck of computer cards one needs to change only three cards; a title card, core energy history information card and one with core changes. With this input, the program can provide individual fuel element burn-up for a given period of operation and the k eff of the core. If a new loading is desired, a new master deck containing the changes is also automatically provided. The life of a new core loading can be estimated by feeding in projected core burn-up factors and observing the resulting loss in individual fuel elements. The code input and output formats have now been made sufficiently convenient and informative as to be incorporated into a standard activity for the Reactor Operations Supervisor. (author)

TMI-related requirements for new operating licenses. Technical report

International Nuclear Information System (INIS)

1980-06-01

There are four types of TMI-related requirements and actions approved by the Commission for new operating licenses: (1) those required to be completed by a license applicant prior to receiving a fuel-loading and low-power testing license, (2) those required to be completed by a license applicant prior to receiving a license to operate at appreciable power levels up to full power, (3) those the NRC will take prior to issuing a fuel-loading and low-power testing or a full-power operating license, and (4) those required to be completed by a licensee prior to a specified date. In this report, only those dated requirements that have already been issued are of interest. Other dated requirements are expected to be issued in the future as work progresses in accordance with the TMI Action Plan. This report summarizes the several parts of the list of TMI-related requirements approved by the Commission for new operating licenses

Ergonomic requirements for the operation of machines and technical equipment

Directory of Open Access Journals (Sweden)

Górny Adam

2017-01-01

Full Text Available In order to operate machinery and equipment safely, it is critical for the solutions in place to conform to design-related and operating requirements. Design-related requirements are primarily the responsibility of machine designers/developers and manufacturers. Operating requirements should be satisfied by employers, who are responsible for ensuring safe working conditions for their employees. Under applicable laws, machinery and equipment should be designed, produced and then operated without placing excessive loads on workers and in keeping with machine functionality and intended use. One should also ensure that machinery and equipment can be maintained and adjusted without exposing their operators to hazards. Ergonomic criteria are an integral part of such requirements. They ensure that human users and operators of technical equipment are enabled to function properly. Design-related requirements are viewed as a priority safety consideration. While they facilitate the use of technical tools, the actual safety of employees ultimately depends on the satisfaction of specific requirements during operation.

Sensitivity Analysis of Input Parameters for the Dose Assessment from Gaseous Effluents due to the Normal Operation of Jordan Research and Training Reactor

International Nuclear Information System (INIS)

Kim, Sukhoon; Lee, Seunghee; Kim, Juyoul; Kim, Juyub; Han, Moonhee

2015-01-01

In this study, therefore, the sensitivity analysis of input variables for the dose assessment was performed for reviewing the effect of each parameter on the result after determining the type and range of parameters that could affect the exposure dose of the public. (Since JRTR will be operated by the concept of 'no liquid discharge,' the input parameters used for calculation of dose due to liquid effluents are not considered in the sensitivity analysis.) In this paper, the sensitivity analysis of input parameters for the dose assessment in the vicinity of the site boundary due to gaseous effluents was performed for a total of thirty-five (35) cases. And, detailed results for the input variables that have an significant effect are shown in Figures 1 through 7, respectively. For preparing a R-ER for the operating license of the JRTR, these results will be updated by the additional information and could be applied to predicting the variation trend of the exposure dose in the process of updating the input parameters for the dose assessment reflecting the characteristics of the JRTR site

Safety of nuclear power plants: Operation. Safety requirements

International Nuclear Information System (INIS)

2004-01-01

The safety of a nuclear power plant is ensured by means of its proper siting, design, construction and commissioning, followed by the proper management and operation of the plant. In a later phase, proper decommissioning is required. This Safety Requirements publication supersedes the Code on the Safety of Nuclear Power Plants: Operation, which was issued in 1988 as Safety Series No. 50-C-O (Rev. 1). The purpose of this revision was: to restructure Safety Series No. 50-C-O (Rev. 1) in the light of the basic objectives, concepts and principles in the Safety Fundamentals publication The Safety of Nuclear Installations. To be consistent with the requirements of the International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources. And to reflect current practice and new concepts and technical developments. Guidance on fulfillment of these Safety Requirements may be found in the appropriate Safety Guides relating to plant operation. The objective of this publication is to establish the requirements which, in the light of experience and the present state of technology, must be satisfied to ensure the safe operation of nuclear power plants. These requirements are governed by the basic objectives, concepts and principles that are presented in the Safety Fundamentals publication The Safety of Nuclear Installations. This publication deals with matters specific to the safe operation of land based stationary thermal neutron nuclear power plants, and also covers their commissioning and subsequent decommissioning

Safety of nuclear power plants: Operation. Safety requirements

International Nuclear Information System (INIS)

2003-01-01

The safety of a nuclear power plant is ensured by means of its proper siting, design, construction and commissioning, followed by the proper management and operation of the plant. In a later phase, proper decommissioning is required. This Safety Requirements publication supersedes the Code on the Safety of Nuclear Power Plants: Operation, which was issued in 1988 as Safety Series No. 50-C-O (Rev. 1). The purpose of this revision was: to restructure Safety Series No. 50-C-O (Rev. 1) in the light of the basic objectives, concepts and principles in the Safety Fundamentals publication The Safety of Nuclear Installations. To be consistent with the requirements of the International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources. And to reflect current practice and new concepts and technical developments. Guidance on fulfillment of these Safety Requirements may be found in the appropriate Safety Guides relating to plant operation. The objective of this publication is to establish the requirements which, in the light of experience and the present state of technology, must be satisfied to ensure the safe operation of nuclear power plants. These requirements are governed by the basic objectives, concepts and principles that are presented in the Safety Fundamentals publication The Safety of Nuclear Installations. This publication deals with matters specific to the safe operation of land based stationary thermal neutron nuclear power plants, and also covers their commissioning and subsequent decommissioning

Safety of nuclear power plants: Operation. Safety requirements

International Nuclear Information System (INIS)

2000-01-01

The safety of a nuclear power plant is ensured by means of its proper siting, design, construction and commissioning, followed by the proper management and operation of the plant. In a later phase, proper decommissioning is required. This Safety Requirements publication supersedes the Code on the Safety of Nuclear Power Plants: Operation, which was issued in 1988 as Safety Series No. 50-C-O (Rev. 1). The purpose of this revision was: to restructure Safety Series No. 50-C-O (Rev. 1) in the light of the basic objectives, concepts and principles in the Safety Fundamentals publication The Safety of Nuclear Installations; to be consistent with the requirements of the International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources; and to reflect current practice and new concepts and technical developments. Guidance on fulfillment of these Safety Requirements may be found in the appropriate Safety Guides relating to plant operation. The objective of this publication is to establish the requirements which, in the light of experience and the present state of technology, must be satisfied to ensure the safe operation of nuclear power plants. These requirements are governed by the basic objectives, concepts and principles that are presented in the Safety Fundamentals publication The Safety of Nuclear Installations. This publication deals with matters specific to the safe operation of land based stationary thermal neutron nuclear power plants, and also covers their commissioning and subsequent decommissioning

Remote media vision-based computer input device

Science.gov (United States)

Arabnia, Hamid R.; Chen, Ching-Yi

1991-11-01

In this paper, we introduce a vision-based computer input device which has been built at the University of Georgia. The user of this system gives commands to the computer without touching any physical device. The system receives input through a CCD camera; it is PC- based and is built on top of the DOS operating system. The major components of the input device are: a monitor, an image capturing board, a CCD camera, and some software (developed by use). These are interfaced with a standard PC running under the DOS operating system.

Input data requirements for special processors in the computation system containing the VENTURE neutronics code

International Nuclear Information System (INIS)

Vondy, D.R.; Fowler, T.B.; Cunningham, G.W.

1976-11-01

This report presents user input data requirements for certain special processors in a nuclear reactor computation system. These processors generally read data in formatted form and generate binary interface data files. Some data processing is done to convert from the user-oriented form to the interface file forms. The VENTURE diffusion theory neutronics code and other computation modules in this system use the interface data files which are generated

Input data requirements for special processors in the computation system containing the VENTURE neutronics code

International Nuclear Information System (INIS)

Vondy, D.R.; Fowler, T.B.; Cunningham, G.W.

1979-07-01

User input data requirements are presented for certain special processors in a nuclear reactor computation system. These processors generally read data in formatted form and generate binary interface data files. Some data processing is done to convert from the user oriented form to the interface file forms. The VENTURE diffusion theory neutronics code and other computation modules in this system use the interface data files which are generated

A Low-input-voltage Wireless Power Transfer for Biomedical Implants

DEFF Research Database (Denmark)

Jiang, Hao; Bai, Kangjun; Zhu, Weijie

2015-01-01

Wireless power transfer is an essential technology to increase implants' longevity. A pair of inductivelycoupled coils operating at radio-frequency is extensively used to deliver electrical power to implants wirelessly. In this system, a power conditioning circuit is required convert the induced...... in the rectifier for the efficient AC to DC conversion. This requirement results in larger coil size, shorter operating distance or more stringent geometrical alignment between the two coils. In this paper, a low-input-voltage wireless power transfer has been demonstrated. In this system, the opencircuit voltage...... time-varying AC power harvested by the receiving coil to a stable DC power that is needed for powering circuits and sensors. Most existing power conditioning circuits require the induced voltage of the receiving coil to be significantly higher than the turn-on voltage of the diodes used...

25 CFR 142.8 - Is economy of operation a requirement for the Alaska Resupply Operation?

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Is economy of operation a requirement for the Alaska... FINANCIAL ACTIVITIES ALASKA RESUPPLY OPERATION § 142.8 Is economy of operation a requirement for the Alaska..., or cooperative arrangements. Whenever possible joint arrangements for economy will be entered into...

Operating safety requirements for the intermediate level liquid waste system

International Nuclear Information System (INIS)

1980-07-01

The operation of the Intermediate Level Liquid Waste (ILW) System, which is described in the Final Safety Analysis, consists of two types of operations, namely: (1) the operation of a tank farm which involves the storage and transportation through pipelines of various radioactive liquids; and (2) concentration of the radioactive liquids by evaporation including rejection of the decontaminated condensate to the Waste Treatment Plant and retention of the concentrate. The following safety requirements in regard to these operations are presented: safety limits and limiting control settings; limiting conditions for operation; and surveillance requirements. Staffing requirements, reporting requirements, and steps to be taken in the event of an abnormal occurrence are also described

Estimated water requirements for gold heap-leach operations

Science.gov (United States)

Bleiwas, Donald I.

2012-01-01

This report provides a perspective on the amount of water necessary for conventional gold heap-leach operations. Water is required for drilling and dust suppression during mining, for agglomeration and as leachate during ore processing, to support the workforce (requires water in potable form and for sanitation), for minesite reclamation, and to compensate for water lost to evaporation and leakage. Maintaining an adequate water balance is especially critical in areas where surface and groundwater are difficult to acquire because of unfavorable climatic conditions [arid conditions and (or) a high evaporation rate]; where there is competition with other uses, such as for agriculture, industry, and use by municipalities; and where compliance with regulatory requirements may restrict water usage. Estimating the water consumption of heap-leach operations requires an understanding of the heap-leach process itself. The task is fairly complex because, although they all share some common features, each gold heap-leach operation is unique. Also, estimating the water consumption requires a synthesis of several fields of science, including chemistry, ecology, geology, hydrology, and meteorology, as well as consideration of economic factors.

An input shaping controller enabling cranes to move without sway

International Nuclear Information System (INIS)

Singer, N.; Singhose, W.; Kriikku, E.

1997-01-01

A gantry crane at the Savannah River Technology Center was retrofitted with an Input Shaping controller. The controller intercepts the operator's pendant commands and modifies them in real time so that the crane is moved without residual sway in the suspended load. Mechanical components on the crane were modified to make the crane suitable for the anti-sway algorithm. This paper will describe the required mechanical modifications to the crane, as well as, a new form of Input Shaping that was developed for use on the crane. Experimental results are presented which demonstrate the effectiveness of the new process. Several practical considerations will be discussed including a novel (patent pending) approach for making small, accurate moves without residual oscillations

21 CFR 111.110 - What quality control operations are required for laboratory operations associated with the...

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for laboratory operations associated with the production and process control system? 111.110 Section 111.110 Food... § 111.110 What quality control operations are required for laboratory operations associated with the...

Fuel supply shutdown facility interim operational safety requirements

International Nuclear Information System (INIS)

Besser, R.L.; Brehm, J.R.; Benecke, M.W.; Remaize, J.A.

1995-01-01

These Interim Operational Safety Requirements (IOSR) for the Fuel Supply Shutdown (FSS) facility define acceptable conditions, safe boundaries, bases thereof, and management or administrative controls to ensure safe operation. The IOSRs apply to the fuel material storage buildings in various modes (operation, storage, surveillance)

Management of Operational Support Requirements for Manned Flight Missions

Science.gov (United States)

1991-01-01

This Instruction establishes responsibilities for managing the system whereby operational support requirements are levied for support of manned flight missions including associated payloads. This management system will ensure that support requirements are properly requested and responses are properly obtained to meet operational objectives.

A Study on the Deriving Requirements of ARGO Operation System

Directory of Open Access Journals (Sweden)

Yoon-Kyung Seo

2009-12-01

Full Text Available Korea Astronomy and Space Science Institute (KASI has been developing one mobile and one stationary SLR system since 2008 named as ARGO-M and ARGO-F, respectively. KASI finished the step of deriving the system requirements of ARGO. The requirements include definitions and scopes of various software and hardware components which are necessary for developing the ARGO-M operation system. And the requirements define function, performance, and interface requirements. The operation system consisting of ARGO-M site, ARGO-F site, and Remote Operation Center (ROC inside KASI is designed for remote access and the automatic tracking and control system which are the main operation concept of ARGO system. To accomplish remote operation, we are considering remote access to ARGO-F and ARGO-M from ROC. The mobile-phone service allows us to access the ARGO-F remotely and to control the system in an emergency. To implement fully automatic tracking and control function in ARGO-F, we have investigated and described the requirements about the automatic aircraft detection system and the various meteorological sensors. This paper addresses the requirements of ARGO Operation System.

Basic national requirements for safe design, construction and operation

International Nuclear Information System (INIS)

Franzen, L.F.

1980-01-01

Nuclear power plants have to be save. Vendors and utilities operating such plants, are convinced that their plants meet this requirement. Who, however, is establishing the safety requirements to be met by those manufacturing and operating nuclear power plants. What are the mechanisms to control whether the features provided assure the required safety level. Who controls whether the required and planned safety features are really provided. Who is eventually responsible for assuring safety after commissioning of a nuclear power plant. These fundamental questions being raised in many discussions on safety and environmental protection are dealt with in the following sections: (1) Fundamental safety requirements on nuclear power plants, in which such items as risk, legal bases and licensing procedure are discussed, (2) Surveillance during construction, in which safety analysis report, siting, safety evaluation, document examination, quality assurance, and commissioning testing are dealt with, (3) Operating tests and conditions in which recurrent inspections, environmental protection during operation, investigation of abnormal occurences and backfitting requirements as reviewed, and (4) Safety philosophy and safety policy to conclude this presentation. The German approach to nuclear safety serves as an example for an effective way of assuring safe nuclear power. (orig.)

Control Board Digital Interface Input Devices – Touchscreen, Trackpad, or Mouse?

Energy Technology Data Exchange (ETDEWEB)

Thomas A. Ulrich; Ronald L. Boring; Roger Lew

2015-08-01

The authors collaborated with a power utility to evaluate input devices for use in the human system interface (HSI) for a new digital Turbine Control System (TCS) at a nuclear power plant (NPP) undergoing a TCS upgrade. A standalone dynamic software simulation of the new digital TCS and a mobile kiosk were developed to conduct an input device study to evaluate operator preference and input device effectiveness. The TCS software presented the anticipated HSI for the TCS and mimicked (i.e., simulated) the turbine systems’ responses to operator commands. Twenty-four licensed operators from the two nuclear power units participated in the study. Three input devices were tested: a trackpad, mouse, and touchscreen. The subjective feedback from the survey indicates the operators preferred the touchscreen interface. The operators subjectively rated the touchscreen as the fastest and most comfortable input device given the range of tasks they performed during the study, but also noted a lack of accuracy for selecting small targets. The empirical data suggest the mouse input device provides the most consistent performance for screen navigation and manipulating on screen controls. The trackpad input device was both empirically and subjectively found to be the least effective and least desired input device.

Fuel Supply Shutdown Facility Interim Operational Safety Requirements

International Nuclear Information System (INIS)

BENECKE, M.W.

2000-01-01

The Interim Operational Safety Requirements for the Fuel Supply Shutdown (FSS) Facility define acceptable conditions, safe boundaries, bases thereof, and management of administrative controls to ensure safe operation of the facility

Operation and maintenance requirements of system design bases

International Nuclear Information System (INIS)

Banerjee, A.K.; Hanley, N.E.

1989-01-01

All system designs make assumptions about system operation testing, inspection, and maintenance. Existing industry codes and standards explicitly address design requirements of new systems, while issues related to system and plant reliability, life, design margins, effects of service conditions, operation, maintenance, etc., usually are implicit. However, system/component design documents of existing power plants often address the code requirements without considering the operation, maintenance, inspection, and testing (OMIT) requirements. The nuclear industry is expending major efforts at most nuclear power plants to reassemble and/or reconstitute system design bases. Stone ampersand Webster Engineering Corporation (SWEC) recently addressed the OMIT requirements of system/component design as an integral part of a utility's preventive maintenance program. For each component, SWEC reviewed vendor recommendations, NPRDS data/industry experience, the existing maintenance program, component service conditions, and actual plant experience. A maintenance program that considers component service conditions and plant experience ensures a connection between maintenance and design basis. Root cause analysis of failure and engineering evaluation of service condition are part of the program. System/component OMIT requirements also are compared against system design, service condition, degradation mechanism, etc., through system/component life-cycle evaluation

Flexible input, dazzling output with IBM i

CERN Document Server

Victória-Pereira, Rafael

2014-01-01

Link your IBM i system to the modern business server world! This book presents easier and more flexible ways to get data into your IBM i system, along with rather surprising methods to export and present the vital business data it contains. You'll learn how to automate file transfers, seamlessly connect PC applications with your RPG programs, and much more. Input operations will become more flexible and user-proof, with self-correcting import processes and direct file transfers that require a minimum of user intervention. Also learn novel ways to present information: your DB2 data will look gr

GRUKON - A package of applied computer programs system input and operating procedures of functional modules

International Nuclear Information System (INIS)

Sinitsa, V.V.; Rineiskij, A.A.

1993-04-01

This manual describes a software package for the production of multigroup neutron cross-sections from evaluated nuclear data files. It presents the information necessary for the implementation of the program's modules in the framework of the execution of the program, including: operating procedures of the program, the data input, the macrocommand language, the assignment of the system's procedures. This report also presents the methodology used in the coding of the individual modules: the rules, the syntax, the method of procedures. The report also presents an example of the application of the data processing module. (author)

KAJIAN INPUT ENERGI PADA BUDIDAYA PADI METODE SYSTEM OF RICE INTENSIFICATION Studies on Energy Input in System of Rice Intensification Method of Rice Cultivation

Directory of Open Access Journals (Sweden)

Bambang Purwantana

2012-05-01

Full Text Available System of Rice Intensification (SRI is a rice cultivation method that intensively control and manage macro and micro nutrients as well as irrigation. This paper quantifies and compares the energy uses of SRI and conventional rice cultiva- tion systems. The study was conducted at some SRI’s experimental plots in the districts of Sleman, Kulonprogo, and Bantul, the province of Yogyakarta. The calculation of the energy was based on the farmers’ work schedule, the time required for each operation, the number of laborers, machines, tools, fuel, and all materials and inputs used. The result shows that SRI method consumed 35% less energy to conventional rice cultivation. Energy inputs from seed, water, fertilizer and pesticide were significantly reduces. However, there was higher input of human energy due to compost- ing, land preparation and weeding operations. The specific energy of SRI method was 1.96 MJ ha-1 lower than conven- tional method of 4.43 MJ ha-1. In the SRI method, 56.2 % of energy consumed was classified as direct energy and 43.8% was indirect energy. The SRI method used 61.9 % of renewable energy and 38.1 % of non-renewable energy. The working efficiency in composting and weeding operations should be improved in perspective of machine and tools to reduce the use of human energy. ABSTRAK System of Rice Intensification (SRI, merupakan suatu metode budidaya padi secara intensif dengan pengendalian unsur-unsur hara makro dan mikro disertai pengendalian dan pengaturan kebutuhan air. Penelitian ini bertujuan untuk menganalisis penggunaan energi dan mengidentifikasi kemungkinan penghematan energi pada budidaya padi SRI. Pe- nelitian dilakukan di Kabupaten Sleman, Kulonprogo, dan Bantul, Propinsi Daerah Istimewa Yogyakarta. Pengamatan dilakukan pada plot-plot percobaan budidaya padi SRI dengan melakukan audit seluruh input energi selama proses budidaya dan dikomparasikan dengan input energi pada budidaya padi cara konvensional. Hasil

Distributed Generation using Indirect Matrix Converter in Boost Operating Mode

DEFF Research Database (Denmark)

Liu, Xiong; Loh, Poh Chiang; Wang, Peng

2011-01-01

, reverse power flow operation of IMC can be implemented to meet voltage boost requirement, where the input ac source is connected to the converter's voltage source side and the output utility grid or load is connected to the current source side. This paper proposes control schemes of IMC under reverse...... power flow operation for both grid-connected and isolated modes with distributed generation suggested as a potential application. In grid-connected mode, the commanded power must be extracted from the input ac source to the grid, in addition to guarantee sinusoidal input/output waveforms, unity input...

A 0.8V, 7μA, rail-to-rail input/output, constant Gm operational amplifier in standard digital 0.18μm CMOS

OpenAIRE

Citakovic, J; Nielsen, I. Riis; Nielsen, Jannik Hammel; Asbeck, P; Andreani, Pietro

2005-01-01

A two-stage amplifier, operational at 0.8V and drawing 7μA, has been integrated in a standard digital 0.18μm CMOS process. Rail-to-rail operations at the input are enabled by complementary transistor pairs with gm control. The efficient rail-to-rail output stage is biased in class AB. The measured DC gain of the amplifier is 75dB, and the unity-gain frequency is 870kHz with a 12pF, 100kΩload. Both input and output stage transistors are biased in weak inversion.

Supplement to safety analysis report. 306-W building operations safety requirement

International Nuclear Information System (INIS)

Richey, C.R.

1979-08-01

The operations safety requirements (OSRs) presented in this report define the conditions, safe boundaries, and management control needed for safely conducting operations with radioactive materials in the Pacific Northwest Laboratory (PNL) 306-W building. The safety requirements are organized in five sections. Safety limits are safety-related process variables that are observable and measurable. Limiting conditions cover: equipment and technical conditions and characteristics of the facility and operations necessary for continued safe operation. Surveillance requirements prescribe the requirements for checking systems and components that are essential to safety. Equipment design controls require that changes to process equipment and systems be independently checked and approved to assure that the changes will have no adverse effect on safety. Administrative controls describe and discuss the organization and administrative systems and procedures to be used for safe operation of the facility. Details of the implementation of the operations safety requirements are prescribed by internal PNL documents such as criticality safety specifications and radiation work procedures

Input Shaping enhanced Active Disturbance Rejection Control for a twin rotor multi-input multi-output system (TRMS).

Science.gov (United States)

Yang, Xiaoyan; Cui, Jianwei; Lao, Dazhong; Li, Donghai; Chen, Junhui

2016-05-01

In this paper, a composite control based on Active Disturbance Rejection Control (ADRC) and Input Shaping is presented for TRMS with two degrees of freedom (DOF). The control tasks consist of accurately tracking desired trajectories and obtaining disturbance rejection in both horizontal and vertical planes. Due to un-measurable states as well as uncertainties stemming from modeling uncertainty and unknown disturbance torques, ADRC is employed, and feed-forward Input Shaping is used to improve the dynamical response. In the proposed approach, because the coupling effects are maintained in controller derivation, there is no requirement to decouple the TRMS into horizontal and vertical subsystems, which is usually performed in the literature. Finally, the proposed method is implemented on the TRMS platform, and the results are compared with those of PID and ADRC in a similar structure. The experimental results demonstrate the effectiveness of the proposed method. The operation of the controller allows for an excellent set-point tracking behavior and disturbance rejection with system nonlinearity and complex coupling conditions. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

42 CFR 84.145 - Motor-operated blower test; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Motor-operated blower test; minimum requirements... Supplied-Air Respirators § 84.145 Motor-operated blower test; minimum requirements. (a) Motor-operated... connection between the motor and the blower shall be so constructed that the motor may be disengaged from the...

WORM: A general-purpose input deck specification language

International Nuclear Information System (INIS)

Jones, T.

1999-01-01

Using computer codes to perform criticality safety calculations has become common practice in the industry. The vast majority of these codes use simple text-based input decks to represent the geometry, materials, and other parameters that describe the problem. However, the data specified in input files are usually processed results themselves. For example, input decks tend to require the geometry specification in linear dimensions and materials in atom or weight fractions, while the parameter of interest might be mass or concentration. The calculations needed to convert from the item of interest to the required parameter in the input deck are usually performed separately and then incorporated into the input deck. This process of calculating, editing, and renaming files to perform a simple parameter study is tedious at best. In addition, most computer codes require dimensions to be specified in centimeters, while drawings or other materials used to create the input decks might be in other units. This also requires additional calculation or conversion prior to composition of the input deck. These additional calculations, while extremely simple, introduce a source for error in both the calculations and transcriptions. To overcome these difficulties, WORM (Write One, Run Many) was created. It is an easy-to-use programming language to describe input decks and can be used with any computer code that uses standard text files for input. WORM is available, via the Internet, at worm.lanl.gov. A user's guide, tutorials, example models, and other WORM-related materials are also available at this Web site. Questions regarding WORM should be directed to wormatlanl.gov

40 CFR 63.1447 - What are my operation and maintenance requirements?

Science.gov (United States)

2010-07-01

... corrective action according to written procedures specified in your operation and maintenance plan to... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are my operation and maintenance... Maintenance Requirements § 63.1447 What are my operation and maintenance requirements? (a) As required by § 63...

Development of the MARS input model for Ulchin 1/2 transient analyzer

International Nuclear Information System (INIS)

Jeong, J. J.; Kim, K. D.; Lee, S. W.; Lee, Y. J.; Chung, B. D.; Hwang, M.

2003-03-01

KAERI has been developing the NSSS transient analyzer based on best-estimate codes for Ulchin 1/2 plants. The MARS and RETRAN code are used as the best-estimate codes for the NSSS transient analyzer. Among the two codes, the MARS code is to be used for realistic analysis of small- and large-break loss-of-coolant accidents, of which break size is greater than 2 inch diameter. This report includes the input model requirements and the calculation note for the Ulchin 1/2 MARS input data generation (see the Appendix). In order to confirm the validity of the input data, we performed the calculations for a steady state at 100 % power operation condition and a double-ended cold leg break LOCA. The results of the steady-state calculation agree well with the design data. The results of the LOCA calculation seem to be reasonable and consistent with those of other best-estimate calculations. Therefore, the MARS input data can be used as a base input deck for the MARS transient analyzer for Ulchin 1/2

Development of the MARS input model for Ulchin 3/4 transient analyzer

International Nuclear Information System (INIS)

Jeong, J. J.; Kim, K. D.; Lee, S. W.; Lee, Y. J.; Lee, W. J.; Chung, B. D.; Hwang, M. G.

2003-12-01

KAERI has been developing the NSSS transient analyzer based on best-estimate codes.The MARS and RETRAN code are adopted as the best-estimate codes for the NSSS transient analyzer. Among these two codes, the MARS code is to be used for realistic analysis of small- and large-break loss-of-coolant accidents, of which break size is greater than 2 inch diameter. This report includes the MARS input model requirements and the calculation note for the MARS input data generation (see the Appendix) for Ulchin 3/4 plant analyzer. In order to confirm the validity of the input data, we performed the calculations for a steady state at 100 % power operation condition and a double-ended cold leg break LOCA. The results of the steady-state calculation agree well with the design data. The results of the LOCA calculation seem to be reasonable and consistent with those of other best-estimate calculations. Therefore, the MARS input data can be used as a base input deck for the MARS transient analyzer for Ulchin 3/4

The CAIN computer code for the generation of MABEL input data sets: a user's manual

International Nuclear Information System (INIS)

Tilley, D.R.

1983-03-01

CAIN is an interactive FORTRAN computer code designed to overcome the substantial effort involved in manually creating the thermal-hydraulics input data required by MABEL-2. CAIN achieves this by processing output from either of the whole-core codes, RELAP or TRAC, interpolating where necessary, and by scanning RELAP/TRAC output in order to generate additional information. This user's manual describes the actions required in order to create RELAP/TRAC data sets from magnetic tape, to create the other input data sets required by CAIN, and to operate the interactive command procedure for the execution of CAIN. In addition, the CAIN code is described in detail. This programme of work is part of the Nuclear Installations Inspectorate (NII)'s contribution to the United Kingdom Atomic Energy Authority's independent safety assessment of pressurized water reactors. (author)

Lessons Learned for Planning and Estimating Operations Support Requirements

Science.gov (United States)

Newhouse, Marilyn

2011-01-01

Operations (phase E) costs are typically small compared to the spacecraft development and test costs. This, combined with the long lead time for realizing operations costs, can lead projects to focus on hardware development schedules and costs, de-emphasizing estimation of operations support requirements during proposal, early design, and replan cost exercises. The Discovery and New Frontiers (D&NF) programs comprise small, cost-capped missions supporting scientific exploration of the solar system. Even moderate yearly underestimates of the operations costs can present significant LCC impacts for deep space missions with long operational durations, and any LCC growth can directly impact the programs ability to fund new missions. The D&NF Program Office at Marshall Space Flight Center recently studied cost overruns for 7 D&NF missions related to phase C/D development of operational capabilities and phase E mission operations. The goal was to identify the underlying causes for the overruns and develop practical mitigations to assist the D&NF projects in identifying potential operations risks and controlling the associated impacts to operations development and execution costs. The study found that the drivers behind these overruns include overly optimistic assumptions regarding the savings resulting from the use of heritage technology, late development of operations requirements, inadequate planning for sustaining engineering and the special requirements of long duration missions (e.g., knowledge retention and hardware/software refresh), and delayed completion of ground system development work. This presentation summarizes the study and the results, providing a set of lessons NASA can use to improve early estimation and validation of operations costs.

Waste Encapsulation and Storage Facility interim operational safety requirements

CERN Document Server

Covey, L I

2000-01-01

The Interim Operational Safety Requirements (IOSRs) for the Waste Encapsulation and Storage Facility (WESF) define acceptable conditions, safe boundaries, bases thereof, and management or administrative controls required to ensure safe operation during receipt and inspection of cesium and strontium capsules from private irradiators; decontamination of the capsules and equipment; surveillance of the stored capsules; and maintenance activities. Controls required for public safety, significant defense-in-depth, significant worker safety, and for maintaining radiological consequences below risk evaluation guidelines (EGs) are included.

Experimental investigation of a low-temperature organic Rankine cycle (ORC) engine under variable heat input operating at both subcritical and supercritical conditions

International Nuclear Information System (INIS)

Kosmadakis, George; Manolakos, Dimitris; Papadakis, George

2016-01-01

Highlights: • Small-scale ORC engine with converted scroll expander is installed at laboratory. • Design suitable for supercritical operation. • ORC engine tested at temperature equal to 95 °C. • Focus is given on expansion and thermal efficiency. • Supercritical operation showed some promising performance. - Abstract: The detailed experimental investigation of an organic Rankine cycle (ORC) is presented, which is designed to operate at supercritical conditions. The net capacity of this engine is almost 3 kW and the laboratory testing of the engine includes the variation of the heat input and of the hot water temperature. The maximum heat input is 48 kW_t_h, while the hot water temperature ranges from 65 up to 100°C. The tests are conducted at the laboratory and the heat source is a controllable electric heater, which can keep the hot water temperature constant, by switching on/off its electrical resistances. The expansion machine is a modified scroll compressor with major conversions, in order to be able to operate with safety at high pressure (or even supercritical at some conditions). The ORC engine is equipped with a dedicated heat exchanger of helical coil design, suitable for such applications. The speeds of the expander and ORC pump are regulated with frequency inverters, in order to control the cycle top pressure and heat input. The performance of all components is evaluated, while special attention is given on the supercritical heat exchanger and the scroll expander. The performance tests examined here concern the variation of the heat input, while the hot water temperature is equal to 95 °C. The aim is to examine the engine performance at the design conditions, as well as at off-design ones. Especially the latter ones are very important, since this engine will be coupled with solar collectors at the final configuration, where the available heat is varied to a great extent. The engine has been measured at the laboratory, where a thermal

Input measurements in reprocessing plants

International Nuclear Information System (INIS)

Trincherini, P.R.; Facchetti, S.

1980-01-01

The aim of this work is to give a review of the methods and the problems encountered in measurements in 'input accountability tanks' of irradiated fuel treatment plants. This study was prompted by the conviction that more and more precise techniques and methods should be at the service of safeguards organizations and that ever greater efforts should be directed towards promoting knowledge of them among operators and all those general area of interest includes the nuclear fuel cycle. The overall intent is to show the necessity of selecting methods which produce measurements which are not only more precise but are absolutely reliable both for routine plant operation and for safety checks in the input area. A description and a critical evaluation of the most common physical and chemical methods are provided, together with an estimate of the precision and accuracy obtained in real operating conditions

Input-output analysis of energy requirements for short rotation, intensive culture, woody biomass

International Nuclear Information System (INIS)

Strauss, C.H.; Grado, S.C.

1992-01-01

A production model for short rotation, intensive culture (SRIC) plantations was developed to determine the energy and financial cost of woody biomass. The model was based on hybrid poplars planted on good quality agricultural sites at a density of 2100 cuttings ha -1 , with average annual growth forecast at 16 metric tonne, oven dry (mg(OD)). Energy and financial analyses showed preharvest cost 4381 megajoules (MJ) Mg -1 (OD) and $16 (US) Mg -1 (OD). Harvesting and transportation requirements increased the total costs 6130 MJ Mg -1 (OD) and $39 Mg -1 (OD) for the delivered material. On an energy cost basis, the principal input was land, whereas on a financial basis, costs were more uniformly distributed among equipment, land, labor, and materials and fuel

47 CFR 80.163 - Operator requirements of the Bridge-to-Bridge Act.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Operator requirements of the Bridge-to-Bridge... Requirements § 80.163 Operator requirements of the Bridge-to-Bridge Act. Each ship subject to the Bridge-to-Bridge Act must have on board a radio operator who holds a restricted radiotelephone operator permit or...

Primary Paralleled Isolated Boost Converter with Extended Operating Voltage Range

DEFF Research Database (Denmark)

Hernandez Botella, Juan Carlos; Sen, Gökhan; Mira Albert, Maria del Carmen

2012-01-01

Applications requiring wide input and output voltage range cannot often be satisfied by using buck or boost derived topologies. Primary paralleled isolated boost converter (PPIBC) [1]-[2] is a high efficiency boost derived topology. This paper proposes a new operation mode for extending the input...

Current trends in codal requirements for safety in operation of nuclear power plants

International Nuclear Information System (INIS)

Srivasista, K.; Shah, Y.K.; Gupta, S.K.

2006-01-01

The Code of practice on safety in nuclear power plant operation states the requirements to be met during operation of a nuclear power plant for assuring safety. Among various stages of authorization, regulatory body issues authorization for operation of a nuclear power plant, monitors and enforces regulatory requirements. The responsible organization shall have overall responsibility and the plant management shall have the primary responsibility for ensuring safe and efficient operation of its nuclear power plants. A set of codal requirements covering technical and administrative aspects are mandatory for the plant management to implement to ensure that the nuclear power plant is operated in accordance with the design intent. Requirements on operating procedures and instructions establish operation and maintenance, inspection and testing of the plant in a planned and systematic way. The requirements on emergency preparedness programme establish with a reasonable assurance that, in the event of an emergency situation, appropriate measures can be taken to mitigate the consequences. Commissioning requirements verify performance criteria during commissioning to ensure that the design intent and QA requirements are met. Several modifications in systems important to safety required during operation of a nuclear power plant are regulated. However new operational codal requirements arising out of periodic safety review, operational experience feedback, life management, probabilistic safety assessment, physical security, safety convention and obligations and decommissioning are not covered in the present code of practice for safety in nuclear power plant operation. Codal provisions on 'Review by operating organization on aspects of design having implications on operability' are also required to be addressed. The merits in developing such a methodology include acceptance of the design by operating organization, ensuring maintainability, proper layout etc. in the new designs

Prediction of a required dynamic torque for motor-operated butterfly valves

International Nuclear Information System (INIS)

Bae, J. H.; Lee, K. N.; Jeong, W. K.

2002-01-01

This study describes the methodology for predicting a required dynamic torque in motor-operated butterfly valves. The results of this methodology have been compared with test data for motor-operated butterfly valves in nuclear power plant. With the close review of test data and torque prediction, it is concluded that the prediction methodology is conservative to predict a required dynamic torque of motor-operated butterfly valves. In addition, the information of correct differential pressure is vital to predict a required dynamic torque of motor-operated butterfly valves

Development and operation of K-URT data input system

International Nuclear Information System (INIS)

Kim, Yun Jae; Myoung, Noh Hoon; Kim, Jong Hyun; Han, Jae Jun

2010-05-01

Activities for TSPA(Total System Performance Assessment) on the permanent disposal of high level radioactive waste includes production of input data, safety assessment using input data, license procedure and others. These activities are performed in 5 steps as follows; (1) Adequate planning, (2) Controlled execution, (3) Complete documentation, (4) Thorough review, (5) Independent oversight. For the confidence building, it is very important to record and manage the materials obtained from research works in transparency. For the documentation of disposal research work from planning stage to data management stage, KAERI developed CYPRUS named CYBER R and D Platform for Radwaste Disposal in Underground System with a QA(Quality Assurance) System. In CYPRUS, QA system makes effects on other functions such as data management, project management and others. This report analyzes the structure of CYPRUS and proposes to accumulate qualified data, to provide a convenient application and to promote access and use of CYPRUS for a future-oriented system

Operations other than war: Requirements for analysis tools research report

Energy Technology Data Exchange (ETDEWEB)

Hartley, D.S. III

1996-12-01

This report documents the research effort to determine the requirements for new or improved analysis tools to support decisions at the strategic and operational levels for military Operations Other than War (OOTW). The work was performed for the Commander in Chief, U.S. Pacific Command (USCINCPAC). The data collection was based on workshops attended by experts in OOTWs: analysis personnel from each of the Combatant Commands, the Services, the Office of the Secretary of Defense (OSD), the Joint Staff, and other knowledgeable personnel. Further data were gathered from other workshops and conferences and from the literature. The results of this research begin with the creation of a taxonomy of OOTWs: categories of operations, attributes of operations, and tasks requiring analytical support. The tasks are connected to the Joint Staff`s Universal Joint Task List (UJTL). Historical OOTWs are analyzed to produce frequency distributions by category and responsible CINC. The analysis products are synthesized into a list of requirements for analytical tools and definitions of the requirements. The report concludes with a timeline or roadmap for satisfying the requirements.

Quantifying input uncertainty in an assemble-to-order system simulation with correlated input variables of mixed types

NARCIS (Netherlands)

Akçay, A.E.; Biller, B.

2014-01-01

We consider an assemble-to-order production system where the product demands and the time since the last customer arrival are not independent. The simulation of this system requires a multivariate input model that generates random input vectors with correlated discrete and continuous components. In

Shaped input distributions for structural damage localization

DEFF Research Database (Denmark)

Ulriksen, Martin Dalgaard; Bernal, Dionisio; Damkilde, Lars

2018-01-01

localization method is cast that operates on the premise of shaping inputs—whose spatial distribution is fixed—by use of a model, such that these inputs, in one structural subdomain at a time, suppress certain steady-state vibration quantities (depending on the type of damage one seeks to interrogate for......). Accordingly, damage is localized when the vibration signature induced by the shaped inputs in the damaged state corresponds to that in the reference state, hereby implying that the approach does not point directly to damage. Instead, it operates with interrogation based on postulated damage patterns...

Development of 20 kW input power coupler for 1.3 GHz ERL main linac. Component test at 30 kW IOT test stand

International Nuclear Information System (INIS)

Sakai, Hiroshi; Umemori, Kensei; Sakanaka, Shogo; Takahashi, Takeshi; Furuya, Takaaki; Shinoe, Kenji; Ishii, Atsushi; Nakamura, Norio; Sawamura, Masaru

2009-01-01

We started to develop an input coupler for a 1.3 GHz ERL superconducting cavity. Required input power is about 20 kW for the cavity acceleration field of 20 MV/m and the beam current of 100 mA in energy recovery operation. The input coupler is designed based on the STF-BL input coupler and some modifications are applied to the design for the CW 20 kW power operation. We fabricated input coupler components such as ceramic windows and bellows and carried out the high-power test of the components by using a 30 kW IOT power source and a test stand constructed for the highpower test. In this report, we mainly describe the results of the high-power test of ceramic window and bellows. (author)

Remote input/output station

CERN Multimedia

1972-01-01

A general view of the remote input/output station installed in building 112 (ISR) and used for submitting jobs to the CDC 6500 and 6600. The card reader on the left and the line printer on the right are operated by programmers on a self-service basis.

Comparative Study on Research Reactor Operation Requirements of IAEA and Korea

International Nuclear Information System (INIS)

Yune, Young Gill; Chang, Woo Joon; Lee, Jinho

2014-01-01

The IAEA safety requirements represent a consensus view of the IAEA's member states and encompass the recommendations of international experts for the safety of the research reactor. The IAEA safety standards are acknowledged as a global standard by most countries in the world. Therefore, it is desirable to harmonize domestic safety requirements with those of the IAEA. Also, since the IAEA safety requirements include international endeavors to strengthen nuclear safety and to apply the latest nuclear safety technologies to nuclear facilities, a comparative analysis of the safety requirements of the IAEA and Korea for the research reactor will be beneficial to obtaining the insights to improve regulations of the research reactor in Korea. For the reason, a comparative study has been conducted for the research reactor operation safety requirements of the IAEA and Korea in this paper. This paper briefly introduced operation safety requirements in the NS-R-4, analysis methods of this study, and the analysis results. A comparative study has been performed on research reactor operation safety requirements of the IAEA and Korea. This study has identified some gaps in operation safety requirements for the NPP of Korea, comparing with those for the research reactor of the IAEA in the following areas: periodic safety assessment, utilization and modification of the reactor, extended shutdown, inspection/testing/maintenance, operating organization, emergency planning, and commissioning

TVF-NMCRC-A powerful program for writing and executing simulation inputs for the FLUKA Monte Carlo Code system

International Nuclear Information System (INIS)

Mark, S.; Khomchenko, S.; Shifrin, M.; Haviv, Y.; Schwartz, J.R.; Orion, I.

2007-01-01

We at the Negev Monte Carlo Research Center (NMCRC) have developed a powerful new interface for writing and executing FLUKA input files-TVF-NMCRC. With the TVF tool a FLUKA user has the ability to easily write an input file without requiring any previous experience. The TVF-NMCRC tool is a LINUX program that has been verified for the most common LINUX-based operating systems, and is suitable for the latest version of FLUKA (FLUKA 2006.3)

Understanding to requirements for educational level in qualification of reactor operators

International Nuclear Information System (INIS)

Zhang Chi; Yang Di; Zhou Limin

2007-01-01

Requirements for qualification of reactor operators in nuclear safety regulations were discussed in this paper. The new issue was described in the confirmation of education level of reactor operators. The understanding to the requirements for Educational Level in Qualification of Reactor Operators was provided according to Higher Education Law of the People's Republic of China. It was proposed to improve the confirmation of qualification of reactor operators as soon as possible. (authors)

Requirements to be made on future information systems in NPP operation

International Nuclear Information System (INIS)

Becker, G.; Distler, K.

1987-01-01

The objective of advanced operational information systems (OIS) is to support and alleviate the operator's work. Human skills and performance limits on the one hand, and the tasks of the operators during various operating states on the other hand are the bases for deriving system design requirements. The paper discusses such aspects like the dynamism of process events, the passive/active role played by the operators in normal/disturbed operation, the compatibility of information representation between OIS and conventional display configuration, parallel versus serial information presentation, team work of operators, parallel processing of tasks within the team; the resulting requirements are derived. (orig./DG) [de

Hydraulic actuator mechanism to control aircraft spoiler movements through dual input commands

Science.gov (United States)

Irick, S. C. (Inventor)

1981-01-01

An aircraft flight spoiler control mechanism is described. The invention enables the conventional, primary spoiler control system to retain its operational characteristics while accommodating a secondary input controlled by a conventional computer system to supplement the settings made by the primary input. This is achieved by interposing springs between the primary input and the spoiler control unit. The springs are selected to have a stiffness intermediate to the greater force applied by the primary control linkage and the lesser resistance offered by the spoiler control unit. Thus, operation of the primary input causes the control unit to yield before the springs, yet, operation of the secondary input, acting directly on the control unit, causes the springs to yield and absorb adjustments before they are transmitted into the primary control system.

75 FR 30395 - Stakeholder Input; National Pollutant Discharge Elimination System (NPDES) Permit Requirements...

Science.gov (United States)

2010-06-01

... peak flow as part of an SSO rulemaking to allow for a holistic and integrated approach to reducing SSOs... Charles Glass, EPA Headquarters, Office of Water, Office of Wastewater Management at tel.: 202-564-0418 or... principles with the following suggested NPDES permit requirements: (1) Capacity, management, operation and...

Usability Improvement for Data Input into the Fatigue Avoidance Scheduling Tool (FAST)

National Research Council Canada - National Science Library

Miller, James C

2005-01-01

...) data input mode than using the graphic schedule input mode. The Grid input mode provided both a statistically and an operationally significant reduction in data input time, compared to the Graphic mode for both novice...

Survey of foreign reactor operator qualifications, training, and staffing requirements. Final report

International Nuclear Information System (INIS)

Au, M.L.; DiSalvo, R.; Merschoff, E.

1982-05-01

The report is a compilation of the data obtained from a survey of foreign nuclear power plant operator requirements. Included among the considerations are: (1) shift staffing; (2) operator eligibility; (3) operator training programs; (4) operator licensing or certification; and (5) operator retraining. The data obtained from this survey are presented in matrix form and contrasted with U.S. requirements

The HAL 9000 Space Operating System Real-Time Planning Engine Design and Operations Requirements

Science.gov (United States)

Stetson, Howard; Watson, Michael D.; Shaughnessy, Ray

2012-01-01

In support of future deep space manned missions, an autonomous/automated vehicle, providing crew autonomy and an autonomous response planning system, will be required due to the light time delays in communication. Vehicle capabilities as a whole must provide for tactical response to vehicle system failures and space environmental effects induced failures, for risk mitigation of permanent loss of communication with Earth, and for assured crew return capabilities. The complexity of human rated space systems and the limited crew sizes and crew skills mix drive the need for a robust autonomous capability on-board the vehicle. The HAL 9000 Space Operating System[2] designed for such missions and space craft includes the first distributed real-time planning / re-planning system. This paper will detail the software architecture of the multiple planning engine system, and the interface design for plan changes, approval and implementation that is performed autonomously. Operations scenarios will be defined for analysis of the planning engines operations and its requirements for nominal / off nominal activities. An assessment of the distributed realtime re-planning system, in the defined operations environment, will be provided as well as findings as it pertains to the vehicle, crew, and mission control requirements needed for implementation.

30 CFR 250.290 - What operations require approval of the Conceptual Plan?

Science.gov (United States)

2010-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Deepwater Operations Plans (dwop) § 250.290 What operations require approval of the Conceptual Plan? You may... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What operations require approval of the...

Environmental requirements for oil and gas operations in Saskatchewan

International Nuclear Information System (INIS)

Nystuen, L.J.

1997-01-01

The administration and regulation of environmental issues regarding the oil and gas industry in Saskatchewan were discussed. The political and cultural differences in Saskatchewan that make environmental processes distinct from its neighbouring jurisdictions were described. The following Saskatchewan legislation deals with environmental requirements: Environmental Management and Protection Act, Environmental Assessment Act, Oil and Gas Conservation Act, Wildlife Habitat Protection Act, Clean Air Act, Planning and Development Act, Forest Act, Water Corporation Act, Heritage Property Act, and Parks Act. The Saskatchewan Department of Energy and Mines (SEM) is the primary regulator of the upstream oil and gas industry. It regulates the construction, operation, reporting and abandonment requirements for oilfield operations. SEM also manages crude oil prior to refining and manages the wastes contaminated with crude oil. Provisions of the relevant Acts regarding drilling in environmentally sensitive areas, flaring requirements, transporting and disposing of oilfield wastes, road-building, operating restrictions, emergency response plans, spill clean-up responsibilities, well abandonment and site reclamation responsibilities were discussed. 8 refs., 2 tabs

High-frequency matrix converter with square wave input

Science.gov (United States)

Carr, Joseph Alexander; Balda, Juan Carlos

2015-03-31

A device for producing an alternating current output voltage from a high-frequency, square-wave input voltage comprising, high-frequency, square-wave input a matrix converter and a control system. The matrix converter comprises a plurality of electrical switches. The high-frequency input and the matrix converter are electrically connected to each other. The control system is connected to each switch of the matrix converter. The control system is electrically connected to the input of the matrix converter. The control system is configured to operate each electrical switch of the matrix converter converting a high-frequency, square-wave input voltage across the first input port of the matrix converter and the second input port of the matrix converter to an alternating current output voltage at the output of the matrix converter.

Operations and Modeling Analysis

Science.gov (United States)

Ebeling, Charles

2005-01-01

The Reliability and Maintainability Analysis Tool (RMAT) provides NASA the capability to estimate reliability and maintainability (R&M) parameters and operational support requirements for proposed space vehicles based upon relationships established from both aircraft and Shuttle R&M data. RMAT has matured both in its underlying database and in its level of sophistication in extrapolating this historical data to satisfy proposed mission requirements, maintenance concepts and policies, and type of vehicle (i.e. ranging from aircraft like to shuttle like). However, a companion analyses tool, the Logistics Cost Model (LCM) has not reached the same level of maturity as RMAT due, in large part, to nonexistent or outdated cost estimating relationships and underlying cost databases, and it's almost exclusive dependence on Shuttle operations and logistics cost input parameters. As a result, the full capability of the RMAT/LCM suite of analysis tools to take a conceptual vehicle and derive its operations and support requirements along with the resulting operating and support costs has not been realized.

Requirements for tokamak remote operation: Application to JT-60SA

International Nuclear Information System (INIS)

Innocente, Paolo; Barbato, Paolo; Farthing, Jonathan; Giruzzi, Gerardo; Ide, Shunsuke; Imbeaux, Frédéric; Joffrin, Emmanuel; Kamada, Yutaka; Kühner, Georg; Naito, Osamu; Urano, Hajime; Yoshida, Maiko

2015-01-01

Highlights: • We analyzed the data management system (DMS) appropriate for international collaboration. • We define the principal requirements for all components of the DMS. • We evaluated application of DMS requirements to the JT-60SA experiment. • We evaluated the role network bandwidth and time delay between EU and Japan. - Abstract: Remote operation and data analysis are becoming key requirements of any fusion devices. In this framework a well-conceived data management system integrated with a suite of analysis and support tools are essential components for an efficient remote exploitation of any fusion device. The following components must be considered: data archiving data model architecture; remote data and computers access; pulse schedule, data analysis software and support tools; remote control room specifications and security issues. The definition of a device-generic data model plays also important role in improving the ability to share solution and reducing learning time. As for the remote control room, the implementation of an Operation Request Gateway has been identified as an answer to security issues meanwhile remotely proving all the required features to effectively operate a device. Previous requirements have been analyzed for the new JT-60SA tokamak device. Remote exploitation is paramount in the JT-60SA case which is expected to be jointly operated between Japan and Europe. Due to the geographical distance of the two parties an optimal remote operation and remote data-analysis is considered as a key requirement in the development of JT-60SA. It this case the effects of network speed and delay have been also evaluated and tests have confirmed that the performance can vary significantly depending on the technology used.

Requirements for tokamak remote operation: Application to JT-60SA

Energy Technology Data Exchange (ETDEWEB)

Innocente, Paolo, E-mail: paolo.innocente@igi.cnr.it [Consorzio RFX, Corso Stati Uniti 4, 35127 Padova (Italy); Barbato, Paolo [Consorzio RFX, Corso Stati Uniti 4, 35127 Padova (Italy); Farthing, Jonathan [CCFE, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Giruzzi, Gerardo [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Ide, Shunsuke [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Imbeaux, Frédéric; Joffrin, Emmanuel [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Kamada, Yutaka [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Kühner, Georg [Max-Planck-Institute for Plasma Physics, EURATOM Association, Wendelsteinstr. 1, 17491 Greifswald (Germany); Naito, Osamu; Urano, Hajime; Yoshida, Maiko [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan)

2015-10-15

Highlights: • We analyzed the data management system (DMS) appropriate for international collaboration. • We define the principal requirements for all components of the DMS. • We evaluated application of DMS requirements to the JT-60SA experiment. • We evaluated the role network bandwidth and time delay between EU and Japan. - Abstract: Remote operation and data analysis are becoming key requirements of any fusion devices. In this framework a well-conceived data management system integrated with a suite of analysis and support tools are essential components for an efficient remote exploitation of any fusion device. The following components must be considered: data archiving data model architecture; remote data and computers access; pulse schedule, data analysis software and support tools; remote control room specifications and security issues. The definition of a device-generic data model plays also important role in improving the ability to share solution and reducing learning time. As for the remote control room, the implementation of an Operation Request Gateway has been identified as an answer to security issues meanwhile remotely proving all the required features to effectively operate a device. Previous requirements have been analyzed for the new JT-60SA tokamak device. Remote exploitation is paramount in the JT-60SA case which is expected to be jointly operated between Japan and Europe. Due to the geographical distance of the two parties an optimal remote operation and remote data-analysis is considered as a key requirement in the development of JT-60SA. It this case the effects of network speed and delay have been also evaluated and tests have confirmed that the performance can vary significantly depending on the technology used.

World Input-Output Network.

Directory of Open Access Journals (Sweden)

Federica Cerina

Full Text Available Production systems, traditionally analyzed as almost independent national systems, are increasingly connected on a global scale. Only recently becoming available, the World Input-Output Database (WIOD is one of the first efforts to construct the global multi-regional input-output (GMRIO tables. By viewing the world input-output system as an interdependent network where the nodes are the individual industries in different economies and the edges are the monetary goods flows between industries, we analyze respectively the global, regional, and local network properties of the so-called world input-output network (WION and document its evolution over time. At global level, we find that the industries are highly but asymmetrically connected, which implies that micro shocks can lead to macro fluctuations. At regional level, we find that the world production is still operated nationally or at most regionally as the communities detected are either individual economies or geographically well defined regions. Finally, at local level, for each industry we compare the network-based measures with the traditional methods of backward linkages. We find that the network-based measures such as PageRank centrality and community coreness measure can give valuable insights into identifying the key industries.

Monitored Geologic Repository Concept of Operations

International Nuclear Information System (INIS)

Curry, P.M.

1999-01-01

This updated document provides the top level guidance for development of the individual systems for the MGR which will be further developed in the System Description Documents. This document will serve as guidance for the development of functional interface and operational requirements. However, the data and engineering values presented in Monitored Geologic Repository Concept of Operations are provided as estimates or summaries of the current design. The original analyses or supporting documents must be utilized if the data or engineering values are used for design inputs. The concepts presented will be utilized as inputs for the development of operational concepts for the individual systems. It is recognized that the references listed may contain existing data or data which are to be verified. However, the data and engineering values presented will not impact the concepts presented in this technical document. As such, the data and engineering values are not being tracked as To Be Verified data. This revision was created to incorporate changes resulting from Enhanced Design Alternative II and Revision 3, DCN 01, of the Monitored Geologic Repository Requirements (YMP 1999)

Development of the MARS input model for Kori nuclear units 1 transient analyzer

International Nuclear Information System (INIS)

Hwang, M.; Kim, K. D.; Lee, S. W.; Lee, Y. J.; Lee, W. J.; Chung, B. D.; Jeong, J. J.

2004-11-01

KAERI has been developing the 'NSSS transient analyzer' based on best-estimate codes for Kori Nuclear Units 1 plants. The MARS and RETRAN codes have been used as the best-estimate codes for the NSSS transient analyzer. Among these codes, the MARS code is adopted for realistic analysis of small- and large-break loss-of-coolant accidents, of which break size is greater than 2 inch diameter. So it is necessary to develop the MARS input model for Kori Nuclear Units 1 plants. This report includes the input model (hydrodynamic component and heat structure models) requirements and the calculation note for the MARS input data generation for Kori Nuclear Units 1 plant analyzer (see the Appendix). In order to confirm the validity of the input data, we performed the calculations for a steady state at 100 % power operation condition and a double-ended cold leg break LOCA. The results of the steady-state calculation agree well with the design data. The results of the LOCA calculation seem to be reasonable and consistent with those of other best-estimate calculations. Therefore, the MARS input data can be used as a base input deck for the MARS transient analyzer for Kori Nuclear Units 1

14 CFR 135.183 - Performance requirements: Land aircraft operated over water.

Science.gov (United States)

2010-01-01

... operated over water. 135.183 Section 135.183 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... AND OPERATIONS OPERATING REQUIREMENTS: COMMUTER AND ON DEMAND OPERATIONS AND RULES GOVERNING PERSONS... operated over water. No person may operate a land aircraft carrying passengers over water unless— (a) It is...

A 0.8V, 7μA, rail-to-rail input/output, constant Gm operational amplifier in standard digital 0.18μm CMOS

DEFF Research Database (Denmark)

Citakovic, J; Nielsen, I. Riis; Nielsen, Jannik Hammel

2005-01-01

A two-stage amplifier, operational at 0.8V and drawing 7μA, has been integrated in a standard digital 0.18μm CMOS process. Rail-to-rail operations at the input are enabled by complementary transistor pairs with gm control. The efficient rail-to-rail output stage is biased in class AB. The measured...

Analysis of the influence of input data uncertainties on determining the reliability of reservoir storage capacity

Directory of Open Access Journals (Sweden)

Marton Daniel

2015-12-01

Full Text Available The paper contains a sensitivity analysis of the influence of uncertainties in input hydrological, morphological and operating data required for a proposal for active reservoir conservation storage capacity and its achieved values. By introducing uncertainties into the considered inputs of the water management analysis of a reservoir, the subsequent analysed reservoir storage capacity is also affected with uncertainties. The values of water outflows from the reservoir and the hydrological reliabilities are affected with uncertainties as well. A simulation model of reservoir behaviour has been compiled with this kind of calculation as stated below. The model allows evaluation of the solution results, taking uncertainties into consideration, in contributing to a reduction in the occurrence of failure or lack of water during reservoir operation in low-water and dry periods.

Pre-operative risk scores for the prediction of outcome in elderly people who require emergency surgery

Directory of Open Access Journals (Sweden)

Bates Tom

2007-06-01

Full Text Available Abstract Background The decision on whether to operate on a sick elderly person with an intra-abdominal emergency is one of the most difficult in general surgery. A predictive risk-score would be of great value in this situation. Methods A Medline search was performed to identify those predictive risk-scores relevant to sick elderly patients in whom emergency surgery might be life-saving. Results Many of the risk scores for surgical patients include the operative findings or require tests which are not available in the acute situation. Most of the relevant studies include younger patients and elective surgery. The Glasgow Aneurysm Score and Hardman Index are specific to ruptured aortic aneurysm while the Boey Score and the Hacetteppe Score are specific to perforated peptic ulcer. The Reiss Index and Fitness Score can be used pre-operatively if the elements of the score can be completed in time. The ASA score, which includes a significant element of subjective clinical judgement, can be augmented with factors such as age and urgency of surgery but no test has a negative predictive value sufficient to recommend against surgical intervention without clinical input. Conclusion Risk scores may be helpful in sick elderly patients needing emergency abdominal surgery but an experienced clinical opinion is still essential.

46 CFR 153.1000 - Special operating requirements for cargoes reactive with water.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Special operating requirements for cargoes reactive with water. 153.1000 Section 153.1000 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... MATERIALS Operations Special Cargo Procedures § 153.1000 Special operating requirements for cargoes reactive...

An anaesthetic pre-operative assessment clinic reduces pre-operative inpatient stay in patients requiring major vascular surgery.

LENUS (Irish Health Repository)

O'Connor, D B

2012-02-01

BACKGROUND: Patients undergoing major vascular surgery (MVS) require extensive anaesthetic assessment. This can require extended pre-operative stays. AIMS: We investigated whether a newly established anaesthetic pre-operative assessment clinic (PAC) would reduce the pre-operative inpatient stay, avoid unnecessary investigations and facilitate day before surgery (DBS) admissions for patients undergoing MVS. PATIENT AND METHODS: One year following and preceding the establishment of the PAC the records of patients undergoing open or endovascular aortic aneurysm repair, carotid endarterectomy and infra-inguinal bypass were reviewed to measure pre-operative length of stay (LoS). RESULTS: Pre-operative LoS was significantly reduced in the study period (1.85 vs. 4.2 days, respectively, P < 0.0001). Only 12 out of 61 patients in 2007 were admitted on the DBS and this increased to 33 out of 63 patients (P = 0.0002). No procedure was cancelled for medical reasons. CONCLUSION: The PAC has facilitated accurate outpatient anaesthetic assessment for patients requiring MVS. The pre-operative in-patient stay has been significantly reduced.

21 CFR 111.135 - What quality control operations are required for product complaints?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for Quality Control § 111.135 What quality control operations are required for...

33 CFR 151.79 - Operating requirements: Discharge of sewage within Antarctica.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Operating requirements: Discharge of sewage within Antarctica. 151.79 Section 151.79 Navigation and Navigable Waters COAST GUARD... Pollution and Sewage § 151.79 Operating requirements: Discharge of sewage within Antarctica. (a) A vessel...

21 CFR 111.65 - What are the requirements for quality control operations?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What are the requirements for quality control... Process Control System § 111.65 What are the requirements for quality control operations? You must implement quality control operations in your manufacturing, packaging, labeling, and holding operations for...

40 CFR 63.9600 - What are my operation and maintenance requirements?

Science.gov (United States)

2010-07-01

... instructions for routine and long-term maintenance. (2) Corrective action procedures for bag leak detection... 40 Protection of Environment 14 2010-07-01 2010-07-01 false What are my operation and maintenance... and Maintenance Requirements § 63.9600 What are my operation and maintenance requirements? (a) As...

14 CFR 91.1055 - Pilot operating limitations and pairing requirement.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Pilot operating limitations and pairing... Ownership Operations Program Management § 91.1055 Pilot operating limitations and pairing requirement. (a... aircraft being flown, and the pilot in command is not an appropriately qualified check pilot, the pilot in...

Application of artificial intelligence to motor operated valve testing

International Nuclear Information System (INIS)

Bogard, T.; Bednar, F.; Matty, T.; Kent, R.

1989-01-01

Improper valve maintenance can be a significant roadblock to successful power plant operation. There have been events during which motor operated valves failed on demand due to improper switch settings. For nuclear electric generating stations, these events have led to regulatory requirements such as NRC Bulletin 85-03 and NRC Bulletin 89-10 Safety Related Motor Operated Valve Testing and Surveillance which imposes strict testing and programmatic requirements on motor operated valves (MOV). Part of the requirements include performing diagnostic testing to verify stem thrust loads and switch settings. Diagnostic equipment must be non-intrusive, minimize valve disassembly, and reduce plant refueling critical path time for testing. In this paper an on-line diagnostic system using sensors to measure stem forces, motor current, and valve position, and a portable system employing these same sensor inputs in addition to torque, limit and torque bypass switch inputs is described. Sophisticated graphic software is employed to display data or trace information. A rule based artificial intelligence (AI) system is used to analyze sensor outputs. Objectives for valve diagnostics, sample AI rules, results of actual field testing, and system software/hardware architecture are presented

Canonic FFT flow graphs for real-valued even/odd symmetric inputs

Science.gov (United States)

Lao, Yingjie; Parhi, Keshab K.

2017-12-01

Canonic real-valued fast Fourier transform (RFFT) has been proposed to reduce the arithmetic complexity by eliminating redundancies. In a canonic N-point RFFT, the number of signal values at each stage is canonic with respect to the number of signal values, i.e., N. The major advantage of the canonic RFFTs is that these require the least number of butterfly operations and only real datapaths when mapped to architectures. In this paper, we consider the FFT computation whose inputs are not only real but also even/odd symmetric, which indeed lead to the well-known discrete cosine and sine transforms (DCTs and DSTs). Novel algorithms for generating the flow graphs of canonic RFFTs with even/odd symmetric inputs are proposed. It is shown that the proposed algorithms lead to canonic structures with N/2 +1 signal values at each stage for an N-point real even symmetric FFT (REFFT) or N/2 -1 signal values at each stage for an N-point RFFT real odd symmetric FFT (ROFFT). In order to remove butterfly operations, several twiddle factor transformations are proposed in this paper. We also discuss the design of canonic REFFT for any composite length. Performances of the canonic REFFT/ROFFT are also discussed. It is shown that the flow graph of canonic REFFT/ROFFT has less number of interconnections, less butterfly operations, and less twiddle factor operations, compared to prior works.

Six axis force feedback input device

Science.gov (United States)

Ohm, Timothy (Inventor)

1998-01-01

The present invention is a low friction, low inertia, six-axis force feedback input device comprising an arm with double-jointed, tendon-driven revolute joints, a decoupled tendon-driven wrist, and a base with encoders and motors. The input device functions as a master robot manipulator of a microsurgical teleoperated robot system including a slave robot manipulator coupled to an amplifier chassis, which is coupled to a control chassis, which is coupled to a workstation with a graphical user interface. The amplifier chassis is coupled to the motors of the master robot manipulator and the control chassis is coupled to the encoders of the master robot manipulator. A force feedback can be applied to the input device and can be generated from the slave robot to enable a user to operate the slave robot via the input device without physically viewing the slave robot. Also, the force feedback can be generated from the workstation to represent fictitious forces to constrain the input device's control of the slave robot to be within imaginary predetermined boundaries.

Applicability of BEE requirements for tour operating enterprises in ...

African Journals Online (AJOL)

This article focuses on tour operating, one of the key sub-sectors of the tourism industry. The research highlights the profile of tour operating enterprises in South Africa, and evaluates their ability to comply with BEE requirements, as well as the utilization of tourism incentives. Data were collected by questionnaire through a ...

New approach to derive linear power/burnup history input for CANDU fuel codes

International Nuclear Information System (INIS)

Lac Tang, T.; Richards, M.; Parent, G.

2003-01-01

The fuel element linear power / burnup history is a required input for the ELESTRES code in order to simulate CANDU fuel behavior during normal operating conditions and also to provide input for the accident analysis codes ELOCA and SOURCE. The purpose of this paper is to present a new approach to derive 'true', or at least more realistic linear power / burnup histories. Such an approach can be used to recreate any typical bundle power history if only a single pair of instantaneous values of bundle power and burnup, together with the position in the channel, are known. The histories obtained could be useful to perform more realistic simulations for safety analyses for cases where the reference (overpower) history is not appropriate. (author)

H∞ memory feedback control with input limitation minimization for offshore jacket platform stabilization

Science.gov (United States)

Yang, Jia Sheng

2018-06-01

In this paper, we investigate a H∞ memory controller with input limitation minimization (HMCIM) for offshore jacket platforms stabilization. The main objective of this study is to reduce the control consumption as well as protect the actuator when satisfying the requirement of the system performance. First, we introduce a dynamic model of offshore platform with low order main modes based on mode reduction method in numerical analysis. Then, based on H∞ control theory and matrix inequality techniques, we develop a novel H∞ memory controller with input limitation. Furthermore, a non-convex optimization model to minimize input energy consumption is proposed. Since it is difficult to solve this non-convex optimization model by optimization algorithm, we use a relaxation method with matrix operations to transform this non-convex optimization model to be a convex optimization model. Thus, it could be solved by a standard convex optimization solver in MATLAB or CPLEX. Finally, several numerical examples are given to validate the proposed models and methods.

Human Systems Integration: Requirements and Functional Decomposition

Science.gov (United States)

Berson, Barry; Gershzohn, Gary; Boltz, Laura; Wolf, Russ; Schultz, Mike

2005-01-01

This deliverable was intended as an input to the Access 5 Policy and Simulation Integrated Product Teams. This document contains high-level pilot functionality for operations in the National Airspace System above FL430. Based on the derived pilot functions the associated pilot information and control requirements are given.

Development of the RETRAN input model for Ulchin 3/4 visual system analyzer

International Nuclear Information System (INIS)

Lee, S. W.; Kim, K. D.; Lee, Y. J.; Lee, W. J.; Chung, B. D.; Jeong, J. J.; Hwang, M. K.

2004-01-01

As a part of the Long-Term Nuclear R and D program, KAERI has developed the so-called Visual System Analyzer (ViSA) based on best-estimate codes. The MARS and RETRAN codes are used as the best-estimate codes for ViSA. Between these two codes, the RETRAN code is used for realistic analysis of Non-LOCA transients and small-break loss-of-coolant accidents, of which break size is less than 3 inch diameter. So it is necessary to develop the RETRAN input model for Ulchin 3/4 plants (KSNP). In recognition of this, the RETRAN input model for Ulchin 3/4 plants has been developed. This report includes the input model requirements and the calculation note for the input data generation (see the Appendix). In order to confirm the validity of the input data, the calculations are performed for a steady state at 100 % power operation condition, inadvertent reactor trip and RCP trip. The results of the steady-state calculation agree well with the design data. The results of the other transient calculations seem to be reasonable and consistent with those of other best-estimate calculations. Therefore, the RETRAN input data can be used as a base input deck for the RETRAN transient analyzer for Ulchin 3/4. Moreover, it is found that Core Protection Calculator (CPC) module, which is modified by Korea Electric Power Research Institute (KEPRI), is well adapted to ViSA

Design requirements, operation and maintenance of gas-cooled reactors

International Nuclear Information System (INIS)

1989-06-01

At the invitation of the Government of the USA the Technical Committee Meeting on Design Requirements, Operation and Maintenance of Gas-Cooled Reactors, was held in San Diego on September 21-23, 1988, in tandem with the GCRA Conference. Both meetings attracted a large contingent of foreign participants. Approximately 100 delegates from 18 different countries participated in the Technical Committee meeting. The meeting was divided into three sessions: Gas-cooled reactor user requirement (8 papers); Gas-cooled reactor improvements to facilitate operation and maintenance (10 papers) and Safety, environmental impacts and waste disposal (5 papers). A separate abstract was prepared for each of these 23 papers. Refs, figs and tabs

Objective ARX Model Order Selection for Multi-Channel Human Operator Identification

NARCIS (Netherlands)

Roggenkämper, N; Pool, D.M.; Drop, F.M.; van Paassen, M.M.; Mulder, M.

2016-01-01

In manual control, the human operator primarily responds to visual inputs but may elect to make use of other available feedback paths such as physical motion, adopting a multi-channel control strategy. Hu- man operator identification procedures generally require a priori selection of the model

Stability Analysis and Stabilization of T-S Fuzzy Delta Operator Systems with Time-Varying Delay via an Input-Output Approach

Directory of Open Access Journals (Sweden)

Zhixiong Zhong

2013-01-01

Full Text Available The stability analysis and stabilization of Takagi-Sugeno (T-S fuzzy delta operator systems with time-varying delay are investigated via an input-output approach. A model transformation method is employed to approximate the time-varying delay. The original system is transformed into a feedback interconnection form which has a forward subsystem with constant delays and a feedback one with uncertainties. By applying the scaled small gain (SSG theorem to deal with this new system, and based on a Lyapunov Krasovskii functional (LKF in delta operator domain, less conservative stability analysis and stabilization conditions are obtained. Numerical examples are provided to illustrate the advantages of the proposed method.

Input Stage for Low-Voltage, Low-Noise Preamplifiers Based on a Floating-Gate MOS Transistor

DEFF Research Database (Denmark)

Igor, Mucha

1997-01-01

A novel input stage for low-voltage, low-noise preamplifiers for integrated capacitive sensors is presented. The input stage of the preamplifier employs floating-gate MOS transistors which are capable of storing the operation point of the input stage over several years without any severe degradat......A novel input stage for low-voltage, low-noise preamplifiers for integrated capacitive sensors is presented. The input stage of the preamplifier employs floating-gate MOS transistors which are capable of storing the operation point of the input stage over several years without any severe...... degradation of the performance of the circuit and without the need for a repeating programming. In this way the noise originating from any resistance previously used for the definition of the operating point is avoided completely and, moreover, by avoiding the input high-pass filter both the saturation...

Safety of Nuclear Power Plants: Commissioning and Operation. Specific Safety Requirements

International Nuclear Information System (INIS)

2017-01-01

This publication is a revision of IAEA Safety Standards Series No. NS-R-2, Safety of Nuclear Power Plants: Operation, and has been extended to cover the commissioning stage. It describes the requirements to be met to ensure the safe commissioning, operation, and transition from operation to decommissioning of nuclear power plants. Over recent years there have been developments in areas such as long term operation of nuclear power plants, plant ageing, periodic safety review, probabilistic safety analysis review and risk informed decision making processes. It became necessary to revise the IAEA’s Safety Requirements in these areas and to correct and/or improve the publication on the basis of feedback from its application by both the IAEA and its Member States. In addition, the requirements are governed by, and must apply, the safety objective and safety principles that are established in the IAEA Safety Standards Series No. SF-1, Fundamental Safety Principles. A review of Safety Requirements publications, initiated in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan, revealed no significant areas of weakness but resulted in a small set of amendments to strengthen the requirements and facilitate their implementation. These are contained in the present publication.

On-grid and Off-grid Operation of Multi-Input Single-Output DC/DC Converter based Fuel Cell Generation System

Directory of Open Access Journals (Sweden)

Noroozian

2009-06-01

Full Text Available This paper presents the modeling and simulation of a proton exchange membrane fuel cell (PEMFC generation system for off-grid and on-grid operation and configuration. A fuel cell DG system consists of a fuel cell power plant, a DC/DC converter and a DC/AC inverter. The dynamic model for fuel cell array and its power electronic interfacing are presented also a multi-input single output (MISO DC/DC converter and its control scheme is proposed and analyzed. This DC/DC converter is capable of interfacing fuel cell arrays to the DC/AC inverter. Also the mathematical model of the inverter is obtained by using average technique. Then the novel control strategy of DC/AC inverter for different operating conditions is demonstrated. The simulation results show the effectiveness of the suggested control systems under both on-grid and off-grid operation modes.

7 CFR 70.110 - Requirements for sanitation, facilities, and operating procedures in official plants.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Requirements for sanitation, facilities, and operating... Requirements for sanitation, facilities, and operating procedures in official plants. (a) The requirements for sanitation, facilities, and operating procedures in official plants shall be the applicable provisions stated...

21 CFR 111.130 - What quality control operations are required for returned dietary supplements?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for... and Process Control System: Requirements for Quality Control § 111.130 What quality control operations are required for returned dietary supplements? Quality control operations for returned dietary...

Metocean input data for drift models applications: Loustic study

International Nuclear Information System (INIS)

Michon, P.; Bossart, C.; Cabioc'h, M.

1995-01-01

Real-time monitoring and crisis management of oil slicks or floating structures displacement require a good knowledge of local winds, waves and currents used as input data for operational drift models. Fortunately, thanks to world-wide and all-weather coverage, satellite measurements have recently enabled the introduction of new methods for the remote sensing of the marine environment. Within a French joint industry project, a procedure has been developed using basically satellite measurements combined to metocean models in order to provide marine operators' drift models with reliable wind, wave and current analyses and short term forecasts. Particularly, a model now allows the calculation of the drift current, under the joint action of wind and sea-state, thus radically improving the classical laws. This global procedure either directly uses satellite wind and waves measurements (if available on the study area) or indirectly, as calibration of metocean models results which are brought to the oil slick or floating structure location. The operational use of this procedure is reported here with an example of floating structure drift offshore from the Brittany coasts

An Analysis of Skill Requirements for Operators of Amphibious Air Cushion Vehicles (ACVs).

Science.gov (United States)

McKnight, A. James; And Others

This report describes the skills required in the operation of an amphibious air cushion vehicle (ACV) in Army tactical and logistic missions. The research involved analyzing ACV characteristics, operating requirements, environmental effects, and results of a simulation experiment. The analysis indicates that ACV operation is complicated by an…

Modeling recognition memory using the similarity structure of natural input

NARCIS (Netherlands)

Lacroix, J.P.W.; Murre, J.M.J.; Postma, E.O.; van den Herik, H.J.

2006-01-01

The natural input memory (NIM) model is a new model for recognition memory that operates on natural visual input. A biologically informed perceptual preprocessing method takes local samples (eye fixations) from a natural image and translates these into a feature-vector representation. During

Using Random Forests to Select Optimal Input Variables for Short-Term Wind Speed Forecasting Models

Directory of Open Access Journals (Sweden)

Hui Wang

2017-10-01

Full Text Available Achieving relatively high-accuracy short-term wind speed forecasting estimates is a precondition for the construction and grid-connected operation of wind power forecasting systems for wind farms. Currently, most research is focused on the structure of forecasting models and does not consider the selection of input variables, which can have significant impacts on forecasting performance. This paper presents an input variable selection method for wind speed forecasting models. The candidate input variables for various leading periods are selected and random forests (RF is employed to evaluate the importance of all variable as features. The feature subset with the best evaluation performance is selected as the optimal feature set. Then, kernel-based extreme learning machine is constructed to evaluate the performance of input variables selection based on RF. The results of the case study show that by removing the uncorrelated and redundant features, RF effectively extracts the most strongly correlated set of features from the candidate input variables. By finding the optimal feature combination to represent the original information, RF simplifies the structure of the wind speed forecasting model, shortens the training time required, and substantially improves the model’s accuracy and generalization ability, demonstrating that the input variables selected by RF are effective.

Multi-Output Power Converter, Operated from a Regulated Input Bus, for the Sireus Rate Sensor

Directory of Open Access Journals (Sweden)

Torrecilla Marcos Compadre

2017-01-01

Full Text Available This paper describes a DC to DC converter designed to meet the power supply requirements of the SiREUS Coarse Rate Sensor (CRS which is a 3-axis MEMS Rate Sensor (MRS that uses a resonating ring gyro and will be used in different ESA missions. The converter supplies +5V, −5V, 3.3V, 1.8V and 40V and it has been designed and prototyped by Clyde Space Ltd with the EQM and FM units being manufactured by Selex ES. The first model was designed for a 28V un-regulated bus and the second model presented here has been designed for a 50V regulated bus. PWM voltage regulation was not used because of the noise requirements and the regulated input bus allowed an unregulated power stage approach. There are also stringent volume and interface constraints, which also affected the design. For such reasons, a fixed dutycycle, quasi-resonant single-ended topology with output linear regulators has been implemented; having the advantages of providing low switching losses, low radiated and conducted noise and no over-voltage failure mode. This paper highlights the techniques used to satisfy stringent noise and protection requirements of the load.

Development of an electrically operated cassava slicing machine

Directory of Open Access Journals (Sweden)

I. S. Aji

2013-08-01

Full Text Available Labor input in manual cassava chips processing is very high and product quality is low. This paper presents the design and construction of an electrically operated cassava slicing machine that requires only one person to operate. Efficiency, portability, ease of operation, corrosion prevention of slicing component of the machine, force required to slice a cassava tuber, capacity of 10 kg/min and uniformity in the size of the cassava chips were considered in the design and fabrication of the machine. The performance of the machine was evaluated with cassava of average length and diameter of 253 mm and 60 mm respectively at an average speed of 154 rpm. The machine produced 5.3 kg of chips of 10 mm length and 60 mm diameter in 1 minute. The efficiency of the machine was 95.6% with respect to the quantity of the input cassava. The chips were found to be well chipped to the designed thickness, shape and of generally similar size. Galvanized steel sheets were used in the cutting section to avoid corrosion of components. The machine is portable and easy to operate which can be adopted for cassava processing in a medium size industry.

Capital planning for operating theatres based on projecting future theatre requirements.

Science.gov (United States)

Sheehan, Jennifer A; Tyler, Peter; Jayasinha, Hirani; Meleady, Kathleen T; Jones, Neill

2011-05-01

During 2006, NSW and ACT Health Departments jointly engaged KPMG to develop an Operating Theatre Requirements' Projection Model and an accompanying planning guideline. A research scan was carried out to identify drivers of surgical demand, theatre capacity and theatre performance, as well as locating existing approaches to modelling operating theatre requirements for planning purposes. The project delivered a Microsoft Excel-based model for projecting future operating theatre requirements, together with an accompanying guideline for use of the model and interpretation of its outputs. It provides a valuable addition to the suite of tools available to Health staff for service and capital planning. The model operates with several limitations, largely due to being data dependent, and the state and completeness of available theatre activity data. However, the operational flexibility built into the model allows users to compensate for these limitations, on a case by case basis, when the user has access to suitable, local data. The design flexibility of the model means that updating the model as improved data become available is not difficult; resulting in revisions being able to be made quickly, and disseminated to users rapidly.

Application of computer voice input/output

International Nuclear Information System (INIS)

Ford, W.; Shirk, D.G.

1981-01-01

The advent of microprocessors and other large-scale integration (LSI) circuits is making voice input and output for computers and instruments practical; specialized LSI chips for speech processing are appearing on the market. Voice can be used to input data or to issue instrument commands; this allows the operator to engage in other tasks, move about, and to use standard data entry systems. Voice synthesizers can generate audible, easily understood instructions. Using voice characteristics, a control system can verify speaker identity for security purposes. Two simple voice-controlled systems have been designed at Los Alamos for nuclear safeguards applicaations. Each can easily be expanded as time allows. The first system is for instrument control that accepts voice commands and issues audible operator prompts. The second system is for access control. The speaker's voice is used to verify his identity and to actuate external devices

Computer Generated Inputs for NMIS Processor Verification

International Nuclear Information System (INIS)

J. A. Mullens; J. E. Breeding; J. A. McEvers; R. W. Wysor; L. G. Chiang; J. R. Lenarduzzi; J. T. Mihalczo; J. K. Mattingly

2001-01-01

Proper operation of the Nuclear Identification Materials System (NMIS) processor can be verified using computer-generated inputs [BIST (Built-In-Self-Test)] at the digital inputs. Preselected sequences of input pulses to all channels with known correlation functions are compared to the output of the processor. These types of verifications have been utilized in NMIS type correlation processors at the Oak Ridge National Laboratory since 1984. The use of this test confirmed a malfunction in a NMIS processor at the All-Russian Scientific Research Institute of Experimental Physics (VNIIEF) in 1998. The NMIS processor boards were returned to the U.S. for repair and subsequently used in NMIS passive and active measurements with Pu at VNIIEF in 1999

H-infinity Control of Linear Systems with Almost Periodic Inputs

DEFF Research Database (Denmark)

Larsen, Mikael

1996-01-01

In this paper we consider the class of linear, infinitedimensional systems with bounded input and output operators. Wederive and QTR H-infinity type result, formulated for thecase where the input signals are almost periodic in a generalizedsense. Control probelms, for which this result is relevant...

Radioactive inputs to the North Sea and the Channel

International Nuclear Information System (INIS)

1984-01-01

The subject is covered in sections: introduction (radioactivity; radioisotopes; discharges from nuclear establishments); data sources (statutory requirements); sources of liquid radioactive waste (figure showing location of principal sources of radioactive discharges; tables listing principal discharges by activity and by nature of radioisotope); Central Electricity Generating Board nuclear power stations; research and industrial establishments; Ministy of Defence establishments; other UK inputs of radioactive waste; total inputs to the North Sea and the Channel (direct inputs; river inputs; adjacent sea areas); conclusions. (U.K.)

Safety requirements for long term operation of NPPs

International Nuclear Information System (INIS)

Houdre, T.; Osouf, N.; Juvin, J.-C.

2012-01-01

In the future, the reactors operating at present will run alongside reactors of the EPR type or their equivalent, designed for a significantly higher level of safety. This raises the question of the acceptability of continued operation of reactors beyond 40 years when there is an available technology that is safer. Two objectives are therefore imperative. First, a re-evaluation of the safety level in the light of that required of EPR type reactors or their equivalent is necessary, with proposals to bring about significant and relevant improvements to the reactors. R and D work in France and elsewhere is already indicating orientations that could lead to answers, and improvements that would provide significant reductions in release in case of severe accident are being studied. Second, strict compliance of the reactors with the applicable regulations must be demonstrated. At the same time, ageing and obsolescence of the equipment will have to be managed. Where these two points are concerned, ASN expects far-reaching proposals from the licensee. With a view to a request for continued operation beyond 40 years, ASN has referred the matter to the Advisory Committee for nuclear reactors which will meet at the end of 2011 to establish the safety requirements for reactors at their fourth ten-yearly outage. (author)

14 CFR 171.273 - Maintenance and operations requirements.

Science.gov (United States)

2010-01-01

... authorized persons. (3) FCC licensing requirements for operations and maintenance personnel. (4) Posting of..., with a maximum corrective maintenance time of not greater than 1.5 hours. This measure applies to... than 1,500 hours. This measure applies to unscheduled outages, out-of-tolerance conditions, and...

Response sensitivity of barrel neuron subpopulations to simulated thalamic input.

Science.gov (United States)

Pesavento, Michael J; Rittenhouse, Cynthia D; Pinto, David J

2010-06-01

Our goal is to examine the relationship between neuron- and network-level processing in the context of a well-studied cortical function, the processing of thalamic input by whisker-barrel circuits in rodent neocortex. Here we focus on neuron-level processing and investigate the responses of excitatory and inhibitory barrel neurons to simulated thalamic inputs applied using the dynamic clamp method in brain slices. Simulated inputs are modeled after real thalamic inputs recorded in vivo in response to brief whisker deflections. Our results suggest that inhibitory neurons require more input to reach firing threshold, but then fire earlier, with less variability, and respond to a broader range of inputs than do excitatory neurons. Differences in the responses of barrel neuron subtypes depend on their intrinsic membrane properties. Neurons with a low input resistance require more input to reach threshold but then fire earlier than neurons with a higher input resistance, regardless of the neuron's classification. Our results also suggest that the response properties of excitatory versus inhibitory barrel neurons are consistent with the response sensitivities of the ensemble barrel network. The short response latency of inhibitory neurons may serve to suppress ensemble barrel responses to asynchronous thalamic input. Correspondingly, whereas neurons acting as part of the barrel circuit in vivo are highly selective for temporally correlated thalamic input, excitatory barrel neurons acting alone in vitro are less so. These data suggest that network-level processing of thalamic input in barrel cortex depends on neuron-level processing of the same input by excitatory and inhibitory barrel neurons.

40 CFR 63.7300 - What are my operation and maintenance requirements?

Science.gov (United States)

2010-07-01

...-term maintenance. (3) Corrective action for all baghouses applied to pushing emissions. In the event a... 40 Protection of Environment 13 2010-07-01 2010-07-01 false What are my operation and maintenance... Battery Stacks Operation and Maintenance Requirements § 63.7300 What are my operation and maintenance...

Real-time transient stabilization and voltage regulation of power generators with unknown mechanical power input

International Nuclear Information System (INIS)

Kenne, Godpromesse; Goma, Raphael; Nkwawo, Homere; Lamnabhi-Lagarrigue, Francoise; Arzande, Amir; Vannier, Jean Claude

2010-01-01

A nonlinear adaptive excitation controller is proposed to enhance the transient stability and voltage regulation of synchronous generators with unknown power angle and mechanical power input. The proposed method is based on a standard third-order model of a synchronous generator which requires only information about the physical available measurements of relative angular speed, active electric power, infinite bus and generator terminal voltages. The operating conditions are computed online using the above physical available measurements, the terminal voltage reference value and the estimate of the mechanical power input. The proposed design is therefore capable of providing satisfactory voltage in the presence of unknown variations of the power system operating conditions. Using the concept of sliding mode equivalent control techniques, a robust decentralized adaptive controller which insures the exponential convergence of the outputs to the desired ones, is obtained. Real-time experimental results are reported, comparing the performance of the proposed adaptive nonlinear control scheme to one of the conventional AVR/PSS controller. The high simplicity of the overall adaptive control scheme and its robustness with respect to line impedance variation including critical unbalanced operating condition and temporary turbine fault, constitute the main positive features of the proposed approach.

Real-time transient stabilization and voltage regulation of power generators with unknown mechanical power input

Energy Technology Data Exchange (ETDEWEB)

Kenne, Godpromesse, E-mail: gokenne@yahoo.co [Laboratoire d' Automatique et d' Informatique Appliquee (LAIA), Departement de Genie Electrique, Universite de Dschang, B.P. 134 Bandjoun (Cameroon); Goma, Raphael, E-mail: raphael.goma@lss.supelec.f [Laboratoire des Signaux et Systemes (L2S), CNRS-SUPELEC, Universite Paris XI, 3 Rue Joliot Curie, 91192 Gif-sur-Yvette (France); Nkwawo, Homere, E-mail: homere.nkwawo@iutv.univ-paris13.f [Departement GEII, Universite Paris XIII, 99 Avenue Jean Baptiste Clement, 93430 Villetaneuse (France); Lamnabhi-Lagarrigue, Francoise, E-mail: lamnabhi@lss.supelec.f [Laboratoire des Signaux et Systemes (L2S), CNRS-SUPELEC, Universite Paris XI, 3 Rue Joliot Curie, 91192 Gif-sur-Yvette (France); Arzande, Amir, E-mail: Amir.arzande@supelec.f [Departement Energie, Ecole Superieure d' Electricite-SUPELEC, 3 Rue Joliot Curie, 91192 Gif-sur-Yvette (France); Vannier, Jean Claude, E-mail: Jean-claude.vannier@supelec.f [Departement Energie, Ecole Superieure d' Electricite-SUPELEC, 3 Rue Joliot Curie, 91192 Gif-sur-Yvette (France)

2010-01-15

A nonlinear adaptive excitation controller is proposed to enhance the transient stability and voltage regulation of synchronous generators with unknown power angle and mechanical power input. The proposed method is based on a standard third-order model of a synchronous generator which requires only information about the physical available measurements of relative angular speed, active electric power, infinite bus and generator terminal voltages. The operating conditions are computed online using the above physical available measurements, the terminal voltage reference value and the estimate of the mechanical power input. The proposed design is therefore capable of providing satisfactory voltage in the presence of unknown variations of the power system operating conditions. Using the concept of sliding mode equivalent control techniques, a robust decentralized adaptive controller which insures the exponential convergence of the outputs to the desired ones, is obtained. Real-time experimental results are reported, comparing the performance of the proposed adaptive nonlinear control scheme to one of the conventional AVR/PSS controller. The high simplicity of the overall adaptive control scheme and its robustness with respect to line impedance variation including critical unbalanced operating condition and temporary turbine fault, constitute the main positive features of the proposed approach.

40 CFR Table 6 to Subpart Ppp of... - Process Vents From Continuous Unit Operations-Monitoring, Recordkeeping, and Reporting Requirements

Science.gov (United States)

2010-07-01

... when insufficient monitoring data are collected. e Boiler or Process Heater with a design heat input... operating value established in the NCS or operating—PR. d,e Condenser f Exit (product side) temperature 1... operating permit—PR. d,e Absorber, Condenser, and Carbon Adsorber (as an alternative to the above...

An information offering system for operation support based on plant functional structure

International Nuclear Information System (INIS)

Ohga, Yukiharu; Seki, Hiroshi

1995-01-01

A plant information offering system was proposed to support operators in their selection and confirmation of the required information for plant operation under transient conditions in nuclear power plants. The system features include an automatic selection method for information and a dialog input method. The former selects plant information in response to plant status changes and operators' demands. The selection is performed based on the knowledge and data as structured by the plant functional structure; i.e. a means-ends abstraction hierarchy model. In the latter, both speech and CRT touch inputs are transformed into words in Japanese to realize an arbitrary input mode combination. The words are analyzed as a sentence before transforming them into a demand for related programs. A prototype system was evaluated using a BWR simulator, assuming abnormal transients such as loss of feedwater. The contents of the offered information were checked based on emergency operation guidelines. It was confirmed that appropriate information items are automatically selected in real time. Answers are generated in reply to the operators' demands. They include information added to reflect the plant conditions. As for dialog, simple and quick input is realized by combining speech and CRT touch according to the operating situation. (author)

A new quantum flux parametron logic gate with large input margin

International Nuclear Information System (INIS)

Hioe, W.; Hosoya, M.; Goto, E.

1991-01-01

This paper reports on the Quantum Flux Parametron (QFP) which is a flux transfer, flux activated Josephson logic device which realizes much lower power dissipation than other Josephson logic devices. Being a two-terminal device its correct operation may be affected by coupling to other QFPs. The problems include backcoupling from active QFPs through inactive QFPs (relay noise), coupling between QFPs activated at different times because of clock skew (homophase noise), and interaction between active QFPs (reaction hazard). Previous QFP circuits worked by wired-majority, which being a linear input logic, has low input margin. A new logic gate (D-gate) using a QFP to perform logic operations has been analyzed and tested by computer simulation. Relay noise, homophase noise and reaction hazard are substantially reduced. Moreover, the input have little interaction hence input margin is greatly improved

46 CFR 167.30-10 - Special operating requirements.

Science.gov (United States)

2010-10-01

..., (3) Within or on the boundaries of fuel tanks; or, (4) To pipe lines, heating coils, pumps, fittings, or other appurtenances connected to such cargo or fuel tanks. (c) Such inspections shall be made and... SCHOOL SHIPS Repairs or Alterations § 167.30-10 Special operating requirements. Inspection and testing...

Decision making in prioritization of required operational capabilities

Science.gov (United States)

Andreeva, P.; Karev, M.; Kovacheva, Ts.

2015-10-01

The paper describes an expert heuristic approach to prioritization of required operational capabilities in the field of defense. Based on expert assessment and by application of the method of Analytical Hierarchical Process, a methodology for their prioritization has been developed. It has been applied to practical simulation decision making games.

Model-based Assessment for Balancing Privacy Requirements and Operational Capabilities

Energy Technology Data Exchange (ETDEWEB)

Knirsch, Fabian [Salzburg Univ. (Austria); Engel, Dominik [Salzburg Univ. (Austria); Frincu, Marc [Univ. of Southern California, Los Angeles, CA (United States); Prasanna, Viktor [Univ. of Southern California, Los Angeles, CA (United States)

2015-02-17

The smart grid changes the way energy is produced and distributed. In addition both, energy and information is exchanged bidirectionally among participating parties. Therefore heterogeneous systems have to cooperate effectively in order to achieve a common high-level use case, such as smart metering for billing or demand response for load curtailment. Furthermore, a substantial amount of personal data is often needed for achieving that goal. Capturing and processing personal data in the smart grid increases customer concerns about privacy and in addition, certain statutory and operational requirements regarding privacy aware data processing and storage have to be met. An increase of privacy constraints, however, often limits the operational capabilities of the system. In this paper, we present an approach that automates the process of finding an optimal balance between privacy requirements and operational requirements in a smart grid use case and application scenario. This is achieved by formally describing use cases in an abstract model and by finding an algorithm that determines the optimum balance by forward mapping privacy and operational impacts. For this optimal balancing algorithm both, a numeric approximation and – if feasible – an analytic assessment are presented and investigated. The system is evaluated by applying the tool to a real-world use case from the University of Southern California (USC) microgrid.

Modeling Recognition Memory Using the Similarity Structure of Natural Input

Science.gov (United States)

Lacroix, Joyca P. W.; Murre, Jaap M. J.; Postma, Eric O.; van den Herik, H. Jaap

2006-01-01

The natural input memory (NAM) model is a new model for recognition memory that operates on natural visual input. A biologically informed perceptual preprocessing method takes local samples (eye fixations) from a natural image and translates these into a feature-vector representation. During recognition, the model compares incoming preprocessed…

User's guide to input for WRAP: a water reactor analysis package

International Nuclear Information System (INIS)

Gregory, M.V.

1977-06-01

The document describes the input records required to execute the Water Reactor Analysis Package (WRAP) for the analysis of thermal-hydraulic transients in primarily light water reactors. The card input required by RELAP4 has been significantly modified to broaden the code's input processing capabilities: (1) All input is in the form of templated, named records. (2) All components (volumes, junctions, etc.) are named rather than numbered, and system relationships are formed by defining associations between the names. (3) A hierarchical part structure is used which allows collections of components to be described as discrete parts (these parts may then be catalogued for use in a wide range of cases). A sample problem, the small break analysis of the Westinghouse Trojan Plant, is discussed and detailed, step-by-step instructions in setting up an input data base are presented. A master list of all input templates for WRAP is compiled

Interconversion of pure Gaussian states requiring non-Gaussian operations

Science.gov (United States)

Jabbour, Michael G.; García-Patrón, Raúl; Cerf, Nicolas J.

2015-01-01

We analyze the conditions under which local operations and classical communication enable entanglement transformations between bipartite pure Gaussian states. A set of necessary and sufficient conditions had been found [G. Giedke et al., Quant. Inf. Comput. 3, 211 (2003)] for the interconversion between such states that is restricted to Gaussian local operations and classical communication. Here, we exploit majorization theory in order to derive more general (sufficient) conditions for the interconversion between bipartite pure Gaussian states that goes beyond Gaussian local operations. While our technique is applicable to an arbitrary number of modes for each party, it allows us to exhibit surprisingly simple examples of 2 ×2 Gaussian states that necessarily require non-Gaussian local operations to be transformed into each other.

30 CFR 939.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 939.784 Section 939.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 941.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 941.784 Section 941.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 933.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 933.784 Section 933.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 921.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 921.784 Section 921.784 Mineral Resources OFFICE OF SURFACE... requirements for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

Fouling resistance prediction using artificial neural network nonlinear auto-regressive with exogenous input model based on operating conditions and fluid properties correlations

Energy Technology Data Exchange (ETDEWEB)

Biyanto, Totok R. [Department of Engineering Physics, Institute Technology of Sepuluh Nopember Surabaya, Surabaya, Indonesia 60111 (Indonesia)

2016-06-03

Fouling in a heat exchanger in Crude Preheat Train (CPT) refinery is an unsolved problem that reduces the plant efficiency, increases fuel consumption and CO{sub 2} emission. The fouling resistance behavior is very complex. It is difficult to develop a model using first principle equation to predict the fouling resistance due to different operating conditions and different crude blends. In this paper, Artificial Neural Networks (ANN) MultiLayer Perceptron (MLP) with input structure using Nonlinear Auto-Regressive with eXogenous (NARX) is utilized to build the fouling resistance model in shell and tube heat exchanger (STHX). The input data of the model are flow rates and temperatures of the streams of the heat exchanger, physical properties of product and crude blend data. This model serves as a predicting tool to optimize operating conditions and preventive maintenance of STHX. The results show that the model can capture the complexity of fouling characteristics in heat exchanger due to thermodynamic conditions and variations in crude oil properties (blends). It was found that the Root Mean Square Error (RMSE) are suitable to capture the nonlinearity and complexity of the STHX fouling resistance during phases of training and validation.

Double input converters for different voltage sources with isolated charger

Directory of Open Access Journals (Sweden)

Chalash Sattayarak

2014-09-01

Full Text Available This paper presents the double input converters for different voltage input sources with isolated charger coils. This research aims to increase the performance of the battery charger circuit. In the circuit, there are the different voltage levels of input source. The operating modes of the switch in the circuit use the microcontroller to control the battery charge and to control discharge mode automatically when the input voltage sources are lost from the system. The experimental result of this research shows better performance for charging at any time period of the switch, while the voltage input sources work together. Therefore, this research can use and develop to battery charger for present or future.

Safety of Nuclear Power Plants: Commissioning and Operation. Specific Safety Requirements

International Nuclear Information System (INIS)

2016-01-01

This publication describes the requirements to be met to ensure the safe operation of nuclear power plants. It takes into account developments in areas such as long term operation of nuclear power plants, plant ageing, periodic safety review, probabilistic safety analysis and risk informed decision making processes. In addition, the requirements are governed by, and must apply, the safety objective and safety principles that are established in the IAEA Safety Standards Series No. SF-1, Fundamental Safety Principles. A review of Safety Requirements publications was commenced in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan. The review revealed no significant areas of weakness and resulted in just a small set of amendments to strengthen the requirements and facilitate their implementation, which are contained in the present publication

Stochastic weather inputs for improved urban water demand forecasting: application of nonlinear input variable selection and machine learning methods

Science.gov (United States)

Quilty, J.; Adamowski, J. F.

2015-12-01

Urban water supply systems are often stressed during seasonal outdoor water use as water demands related to the climate are variable in nature making it difficult to optimize the operation of the water supply system. Urban water demand forecasts (UWD) failing to include meteorological conditions as inputs to the forecast model may produce poor forecasts as they cannot account for the increase/decrease in demand related to meteorological conditions. Meteorological records stochastically simulated into the future can be used as inputs to data-driven UWD forecasts generally resulting in improved forecast accuracy. This study aims to produce data-driven UWD forecasts for two different Canadian water utilities (Montreal and Victoria) using machine learning methods by first selecting historical UWD and meteorological records derived from a stochastic weather generator using nonlinear input variable selection. The nonlinear input variable selection methods considered in this work are derived from the concept of conditional mutual information, a nonlinear dependency measure based on (multivariate) probability density functions and accounts for relevancy, conditional relevancy, and redundancy from a potential set of input variables. The results of our study indicate that stochastic weather inputs can improve UWD forecast accuracy for the two sites considered in this work. Nonlinear input variable selection is suggested as a means to identify which meteorological conditions should be utilized in the forecast.

A parallel input composite transimpedance amplifier

Science.gov (United States)

Kim, D. J.; Kim, C.

2018-01-01

A new approach to high performance current to voltage preamplifier design is presented. The design using multiple operational amplifiers (op-amps) has a parasitic capacitance compensation network and a composite amplifier topology for fast, precision, and low noise performance. The input stage consisting of a parallel linked JFET op-amps and a high-speed bipolar junction transistor (BJT) gain stage driving the output in the composite amplifier topology, cooperating with the capacitance compensation feedback network, ensures wide bandwidth stability in the presence of input capacitance above 40 nF. The design is ideal for any two-probe measurement, including high impedance transport and scanning tunneling microscopy measurements.

Biological 2-Input Decoder Circuit in Human Cells

Science.gov (United States)

2015-01-01

Decoders are combinational circuits that convert information from n inputs to a maximum of 2n outputs. This operation is of major importance in computing systems yet it is vastly underexplored in synthetic biology. Here, we present a synthetic gene network architecture that operates as a biological decoder in human cells, converting 2 inputs to 4 outputs. As a proof-of-principle, we use small molecules to emulate the two inputs and fluorescent reporters as the corresponding four outputs. The experiments are performed using transient transfections in human kidney embryonic cells and the characterization by fluorescence microscopy and flow cytometry. We show a clear separation between the ON and OFF mean fluorescent intensity states. Additionally, we adopt the integrated mean fluorescence intensity for the characterization of the circuit and show that this metric is more robust to transfection conditions when compared to the mean fluorescent intensity. To conclude, we present the first implementation of a genetic decoder. This combinational system can be valuable toward engineering higher-order circuits as well as accommodate a multiplexed interface with endogenous cellular functions. PMID:24694115

Biological 2-input decoder circuit in human cells.

Science.gov (United States)

Guinn, Michael; Bleris, Leonidas

2014-08-15

Decoders are combinational circuits that convert information from n inputs to a maximum of 2(n) outputs. This operation is of major importance in computing systems yet it is vastly underexplored in synthetic biology. Here, we present a synthetic gene network architecture that operates as a biological decoder in human cells, converting 2 inputs to 4 outputs. As a proof-of-principle, we use small molecules to emulate the two inputs and fluorescent reporters as the corresponding four outputs. The experiments are performed using transient transfections in human kidney embryonic cells and the characterization by fluorescence microscopy and flow cytometry. We show a clear separation between the ON and OFF mean fluorescent intensity states. Additionally, we adopt the integrated mean fluorescence intensity for the characterization of the circuit and show that this metric is more robust to transfection conditions when compared to the mean fluorescent intensity. To conclude, we present the first implementation of a genetic decoder. This combinational system can be valuable toward engineering higher-order circuits as well as accommodate a multiplexed interface with endogenous cellular functions.

A Scenario-Based Process for Requirements Development: Application to Mission Operations Systems

Science.gov (United States)

Bindschadler, Duane L.; Boyles, Carole A.

2008-01-01

The notion of using operational scenarios as part of requirements development during mission formulation (Phases A & B) is widely accepted as good system engineering practice. In the context of developing a Mission Operations System (MOS), there are numerous practical challenges to translating that notion into the cost-effective development of a useful set of requirements. These challenges can include such issues as a lack of Project-level focus on operations issues, insufficient or improper flowdown of requirements, flowdown of immature or poor-quality requirements from Project level, and MOS resource constraints (personnel expertise and/or dollars). System engineering theory must be translated into a practice that provides enough structure and standards to serve as guidance, but that retains sufficient flexibility to be tailored to the needs and constraints of a particular MOS or Project. We describe a detailed, scenario-based process for requirements development. Identifying a set of attributes for high quality requirements, we show how the portions of the process address many of those attributes. We also find that the basic process steps are robust, and can be effective even in challenging Project environments.

Human Resources Training Requirement on NPP Operation and Maintenance

International Nuclear Information System (INIS)

Nurlaila; Yuliastuti

2009-01-01

This paper discussed the human resources requirement on Nuclear Power Plant (NPP) operation and maintenance (O&M) phase related with the training required for O&M personnel. In addition, this paper also briefly discussed the availability of training facilities domestically include with some suggestion to develop the training facilities intended for the near future time in Indonesia. This paper was developed under the assumptions that Indonesia will build twin unit of NPP with capacity 1000 MWe for each using the turnkey contract method. The total of NPP O&M personnel were predicted about 692 peoples which consists of 42 personnel located in the head quarter and the rest 650 people work at NPP site. Up until now, Indonesia had the experience on operating and maintaining the nonnuclear power plant and several research reactors namely Kartini Reactor Yogyakarta, Triga Mark II Reactor Bandung, and GA Siwabessy Reactor Serpong. Beside that, experience on operating and maintaining the NPP in other countries would act as one of the reference to Indonesia in formulating an appropriate strategy to develop NPP human resources particularly in O&M phases. Education and training development program could be done trough the cooperation with vendor candidates. (author)

Functional Requirements Document for HALE UAS Operations in the NAS: Step 1. Version 3

Science.gov (United States)

2006-01-01

The purpose of this Functional Requirements Document (FRD) is to compile the functional requirements needed to achieve the Access 5 Vision of "operating High Altitude, Long Endurance (HALE) Unmanned Aircraft Systems (UAS) routinely, safely, and reliably in the national airspace system (NAS)" for Step 1. These functional requirements could support the development of a minimum set of policies, procedures and standards by the Federal Aviation Administration (FAA) and various standards organizations. It is envisioned that this comprehensive body of work will enable the FAA to establish and approve regulations to govern safe operation of UAS in the NAS on a routine or daily "file and fly" basis. The approach used to derive the functional requirements found within this FRD was to decompose the operational requirements and objectives identified within the Access 5 Concept of Operations (CONOPS) into the functions needed to routinely and safely operate a HALE UAS in the NAS. As a result, four major functional areas evolved to enable routine and safe UAS operations for an on-demand basis in the NAS. These four major functions are: Aviate, Navigate, Communicate, and Avoid Hazards. All of the functional requirements within this document can be directly traceable to one of these four major functions. Some functions, however, are traceable to several, or even all, of these four major functions. These cross-cutting functional requirements support the "Command / Control: function as well as the "Manage Contingencies" function. The requirements associated to these high-level functions and all of their supporting low-level functions are addressed in subsequent sections of this document.

Licensing requirements regarding the qualification of operating personnel in nuclear power plants

International Nuclear Information System (INIS)

Fechner, J.B.

1981-01-01

The legal requirements regarding the qualifications of operating personnel in nuclear power plants in the Federal Republic of Germany are outlined as in article 7 of the Atomic Energy Act. For the responsible operating personnel the requisite competence and reliability are legally required; for subordinate personnel the law requires only the necessary knowledge. The requisite competence and the necessary knowledge have been further specified in a set of guidelines by the authorities; work on specification of reliability requirements is under way. Essential elements of the requisite competence of responsible operating personnel are their professional qualification, their safety-related knowledge, their abilities, their practical experience, and - for the responsible shift personnel - their nuclear, plant-related training as well as a written and oral examination. Requalification is indispensible for keeping the requisite competence on a level in accordance with the current state of science and technology. Facts concerning the personal reliability of the responsible operating personnel are assessed by the competent authorities on the basis of information available at other state institutions. For the responsible shift personnel, physical and psychological fitness are important factors contributing to their reliability. The necessary knowledge subordinate operating personnel must possess with respect to plant safety and safety of the personnel is assured via instruction on safety and via special briefings at the working place. Lack of safety-related knowledge has to be compensated for by assigning an experienced permanent supervisor for each activity in question. Current work on qualification of operating personnel concentrates on training, including simulator training, of responsible shift personnel. (author)

33 CFR 157.460 - Additional operational requirements for tank barges.

Science.gov (United States)

2010-07-01

... OF HOMELAND SECURITY (CONTINUED) POLLUTION RULES FOR THE PROTECTION OF THE MARINE ENVIRONMENT... Hulls Carrying Petroleum Oils § 157.460 Additional operational requirements for tank barges. (a...

Steady-state operation requirements of tokamak fusion reactor concepts

International Nuclear Information System (INIS)

Knobloch, A.F.

1991-06-01

In the last two decades tokamak conceptual reactor design studies have been deriving benefit from progressing plasma physics experiments, more depth in theory and increasing detail in technology and engineering. Recent full-scale reactor extrapolations such as the US ARIES-I and the EC Reference Reactor study provide information on rather advanced concepts that are called for when economic boundary conditions are imposed. The ITER international reactor design activity concentrated on defining the next step after the JET generation of experiments. For steady-state operation as required for any future commercial tokamak fusion power plants it is essential to have non-inductive current drive. The current drive power and other internal power requirements specific to magnetic confinement fusion have to be kept as low as possible in order to attain a competitive overall power conversion efficiency. A high plasma Q is primarily dependent on a high current drive efficiency. Since such conditions have not yet been attained in practice, the present situation and the degree of further development required are characterized. Such development and an appropriately designed next-step tokamak reactor make the gradual realization of high-Q operation appear feasible. (orig.)

78 FR 1823 - Cable Television Technical and Operational Requirements

Science.gov (United States)

2013-01-09

... FEDERAL COMMUNICATIONS COMMISSION 47 CFR Part 79 [MB Docket No. 12-217; DA 12-2081] Cable Television Technical and Operational Requirements AGENCY: Federal Communications Commission. ACTION: Proposed rule; extension of reply comment period. SUMMARY: In this document, the Commission extends the deadline...

A new interleaved double-input three-level boost converter

DEFF Research Database (Denmark)

Chen, Jianfei; Hou, Shiying; Sun, Tao

2016-01-01

This paper proposes a new interleaved double-input three-level Boost (DITLB) converter, which is composed of two boost converters indirectly in series. Thus, a high voltage gain, together with a low component stress and a small input current ripple due to the interleaved control scheme, is achieved....... The operating principle of the DITLB converter under the individual supplying power (ISP) and simultaneous supplying power (SSP) mode is analyzed. In addition, closed-loop control strategies composed of a voltage-current loop and a voltage-balance loop, have been researched to make the converter operate...... steadily and to alleviate the neutral-point imbalance issue. Experimental results verify correctness and feasibility of the proposed topology and control strategies....

Manpower requirements for quality assurance during operation

International Nuclear Information System (INIS)

Pratt, J.M.; Sollenberger, L.G.

1982-01-01

As a result of the Three Mile Island accident and the findings presented in various investigatory reports, some fundamental changes are taking place in the role and scope of quality assurance. Recent changes to United States national codes, guides and standards are analysed in order to identify the principles involved. This analysis shows that the scope of the programme is being extended beyond the equipment designated 'nuclear safety related' and greater emphasis is being placed upon the independent verification of the satisfactory performance of activities affecting safety. Such fundamental changes could lead to a significant increase in the number of quality assurance personnel required to support an operating nuclear power plant. The evolving quality assurance organization at Three Mile Island is used to illustrate how these fundamental changes could affect the quality assurance organization and manpower requirements. (author)

40 CFR 63.7710 - What are my operation and maintenance requirements?

Science.gov (United States)

2010-07-01

... defect or deficiency as soon as practicable. (2) Operating limits for each capture system for an... 40 Protection of Environment 13 2010-07-01 2010-07-01 false What are my operation and maintenance requirements? 63.7710 Section 63.7710 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

75 FR 6164 - New Pilot Certification Requirements for Air Carrier Operations

Science.gov (United States)

2010-02-08

.... FAA-2010-0100; Notice No. 10-02] RIN 2120-AJ67 New Pilot Certification Requirements for Air Carrier... to regulations relating to the certification of pilots conducting domestic, flag, and supplemental... qualification requirements for commercial pilot certification are adequate for engaging in such operations. The...

Wide Operating Voltage Range Fuel Cell Battery Charger

DEFF Research Database (Denmark)

Hernandez Botella, Juan Carlos; Mira Albert, Maria del Carmen; Sen, Gokhan

2014-01-01

DC-DC converters for fuel cell applications require wide voltage range operation due to the unique fuel cell characteristic curve. Primary parallel isolated boost converter (PPIBC) is a boost derived topology for low voltage high current applications reaching an efficiency figure up to 98...... by two the converter input-to-output voltage gain. This allows covering the conditions when the fuel cell stack operates in the activation region (maximum output voltage) and increases the degrees of freedom for converter optimization. The transition between operating modes is studied because represents...

36 CFR 228.4 - Plan of operations-notice of intent-requirements.

Science.gov (United States)

2010-07-01

... meet the requirements for environmental protection in § 228.8. (d) The plan of operations shall cover... disturbance not covered by the initial plan. (e) At any time during operations under an approved plan of...), resulting in varying degrees of disturbance to vegetative resources, soil, water, air, or wildlife. The...

Producing a unified progress report with inputs from several contractors

International Nuclear Information System (INIS)

Nelson, O.A.

1981-01-01

The project management organization in which the author works produces an annual technical progress report for the Clinch River Breeder Reactor Plant Project. The report has to be integrated and edited from the inputs of six major Project participants scattered from coast to coast. The integrated report manuscript then has to be submitted for two formal reviews, and the report must be published in a readable and attractive form. Accomplishing those steps in a reasonable length of time, with a high degree of accuracy, and at minimum expense requires careful planning and close supervision. Planning includes scheduling in such a way as to perform operations in parallel, where possible, instead of in series. Exploiting the capabilities of word processing saves much keyboarding and proofreading time. Art from previous reports is reused when possible. Many of these methods can be applied to other reports that require integration and editing of material from several sources

A Simple Square Rooting Circuit Based on Operational Amplifiers (OPAMPs

Directory of Open Access Journals (Sweden)

K. C. Selvam

2013-02-01

Full Text Available A simple circuit which accepts a negative voltage as input and provides an output voltage equal to the square root of the input voltage is described in this paper. The square rooting operation is dependent only on the ratio of two resistors and a DC voltage. Hence, the required accuracy can be obtained by employing precision resistors and a stable reference voltage. The feasibility of the circuit is examined by testing the results on a proto type.

30 CFR 903.784 - Underground mining permit applications-Minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 903.784 Section 903.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, applies to any person who submits an application...

30 CFR 910.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 910.784 Section 910.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. (a) Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 947.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 947.784 Section 947.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. (a) Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes...

30 CFR 942.784 - Underground mining permit applications-Minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 942.784 Section 942.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 921.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 921.780 Section 921.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 922.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 922.784 Section 922.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 933.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 933.780 Section 933.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 905.784 - Underground mining permit applications-Minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 905.784 Section 905.784 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

Study Results on Knowledge Requirements for Entry-Level Airport Operations and Management Personnel

Science.gov (United States)

Quilty, Stephen M.

2005-01-01

This paper identifies important topical knowledge areas required of individuals employed in airport operations and management positions. A total of 116 airport managers and airfield operations personnel responded to a survey that sought to identify the importance of various subject matter for entry level airport operations personnel. The results from this study add to the body of research on aviation management curriculum development and can be used to better develop university curriculum and supplemental training focused on airport management and operations. Recommendations are made for specialized airport courses within aviation management programs. Further, this study identifies for job seekers or individuals employed in entry level positions those knowledge requirements deemed important by airport managers and operations personnel at different sized airports.

Safety of Nuclear Power Plants: Commissioning and Operation. Specific Safety Requirements (Arabic Edition)

International Nuclear Information System (INIS)

2017-01-01

This publication is a revision of IAEA Safety Standards Series No. NS-R-2, Safety of Nuclear Power Plants: Operation, and has been extended to cover the commissioning stage. It describes the requirements to be met to ensure the safe commissioning, operation, and transition from operation to decommissioning of nuclear power plants. Over recent years there have been developments in areas such as long term operation of nuclear power plants, plant ageing, periodic safety review, probabilistic safety analysis review and risk informed decision making processes. It became necessary to revise the IAEA’s Safety Requirements in these areas and to correct and/or improve the publication on the basis of feedback from its application by both the IAEA and its Member States. In addition, the requirements are governed by, and must apply, the safety objective and safety principles that are established in the IAEA Safety Standards Series No. SF-1, Fundamental Safety Principles. A review of Safety Requirements publications, initiated in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan, revealed no significant areas of weakness but resulted in a small set of amendments to strengthen the requirements and facilitate their implementation. These are contained in the present publication.

30 CFR 937.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 937.784 Section 937.784 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 942.780 - Surface mining permit applications-Minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 942.780 Section 942.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 912.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 912.780 Section 912.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 939.780 - Surface mining permit applications-minimum requirements for reclamation and operations plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operations plan. 939.780 Section 939.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operations plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

30 CFR 905.780 - Surface mining permit applications-Minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 905.780 Section 905.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 947.780 - Surface mining permit application-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 947.780 Section 947.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Application—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 910.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 910.780 Section 910.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirement for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 922.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 922.780 Section 922.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 903.780 - Surface mining permit applications-Minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 903.780 Section 903.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, applies to any person who submits an application to conduct...

30 CFR 912.784 - Underground mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 912.784 Section 912.784 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. Part 784 of this chapter, Underground Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 937.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 937.780 Section 937.780 Mineral Resources OFFICE OF SURFACE... reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirement for Reclamation and Operation Plan, shall apply to any person who makes application to conduct...

30 CFR 941.780 - Surface mining permit applications-minimum requirements for reclamation and operation plan.

Science.gov (United States)

2010-07-01

... requirements for reclamation and operation plan. 941.780 Section 941.780 Mineral Resources OFFICE OF SURFACE... for reclamation and operation plan. (a) Part 780 of this chapter, Surface Mining Permit Applications—Minimum Requirements for Reclamation and Operation Plan, shall apply to any person who makes application...

Frequency-domain multiplex with eight-input SQUID and readout electronics over 1MHz

International Nuclear Information System (INIS)

Masui, K.; Takei, Y.; Ikeda, H.; Kimura, S.; Mitsuda, K.; Yamasaki, N.Y.

2006-01-01

In a magnetic summation method, TES and SQUID driving circuits are isolated and thus small crosstalk and stray impedance are expected. Since a FLL circuit with a large bandwidth and a small noise level is required for a SQUID, we designed and produced an electronics to meet our design of multiplexing with an 8-input SQUID. The FLL circuit achieved an open loop-gain bandwidth product of 8MHz with 1m wire length, which is enough for a TES to be operated with a bias current of 70μA, and a noise level of 30pA/Hz

Development of NUPREP PC Version and Input Structures for NUCIRC Single Channel Analyses

International Nuclear Information System (INIS)

Yoon, Churl; Jun, Ji Su; Park, Joo Hwan

2007-12-01

The input file for a steady-state thermal-hydraulic code NUCIRC consists of common channel input data and specific channel input data in a case of single channel analysis. Even when all the data is ready for the 380 channels' single channel analyses, it takes long time and requires enormous effort to compose an input file by hand-editing. The automatic pre-processor for this tedious job is a NUPREP code. In this study, a NUPREP PC version has been developed from the source list in the program manual of NUCIRC-MOD2.000 that is imported in a form of an execution file. In this procedure, some errors found in PC executions and lost statements are fixed accordingly. It is confirmed that the developed NUPREP code produces input file correctly for the CANDU-6 single channel analysis. Additionally, the NUCIRC input structure and data format are summarized for a single channel analysis and the input CARDs required for the creep information of aged channels are listed

Design and evaluation of nonverbal sound-based input for those with motor handicapped.

Science.gov (United States)

Punyabukkana, Proadpran; Chanjaradwichai, Supadaech; Suchato, Atiwong

2013-03-01

Most personal computing interfaces rely on the users' ability to use their hand and arm movements to interact with on-screen graphical widgets via mainstream devices, including keyboards and mice. Without proper assistive devices, this style of input poses difficulties for motor-handicapped users. We propose a sound-based input scheme enabling users to operate Windows' Graphical User Interface by producing hums and fricatives through regular microphones. Hierarchically arranged menus are utilized so that only minimal numbers of different actions are required at a time. The proposed scheme was found to be accurate and capable of responding promptly compared to other sound-based schemes. Being able to select from multiple item-selecting modes helps reducing the average time duration needed for completing tasks in the test scenarios almost by half the time needed when the tasks were performed solely through cursor movements. Still, improvements on facilitating users to select the most appropriate modes for desired tasks should improve the overall usability of the proposed scheme.

Investigating gaze-controlled input in a cognitive selection test

OpenAIRE

Gayraud, Katja; Hasse, Catrin; Eißfeldt, Hinnerk; Pannasch, Sebastian

2017-01-01

In the field of aviation, there is a growing interest in developing more natural forms of interaction between operators and systems to enhance safety and efficiency. These efforts also include eye gaze as an input channel for human-machine interaction. The present study investigates the application of gaze-controlled input in a cognitive selection test called Eye Movement Conflict Detection Test. The test enables eye movements to be studied as an indicator for psychological test performance a...

IFF, Full-Screen Input Menu Generator for FORTRAN Program

International Nuclear Information System (INIS)

Seidl, Albert

1991-01-01

1 - Description of program or function: The IFF-package contains input modules for use within FORTRAN programs. This package enables the programmer to easily include interactive menu-directed data input (module VTMEN1) and command-word processing (module INPCOM) into a FORTRAN program. 2 - Method of solution: No mathematical operations are performed. 3 - Restrictions on the complexity of the problem: Certain restrictions of use may arise from the dimensioning of arrays. Field lengths are defined via PARAMETER-statements

The direct and indirect household energy requirements in the Republic of Korea from 1980 to 2000 - An input-output analysis

International Nuclear Information System (INIS)

Park, Hi-Chun; Heo, Eunnyeong

2007-01-01

As energy conservation can be realized through changes in the composition of goods and services consumed, there is a need to assess indirect and total household energy requirements. The Korean household sector was responsible for about 52% of the national primary energy requirement in the period from 1980 to 2000. Of this total, more than 60% of household energy requirement was indirect. Thus, not only direct but also indirect household energy requirement should be the target of energy conservation policies. Electricity became the main fuel in household energy use in 2000. Households consume more and more electricity intensive goods and services, a sign of increasing living standards. Increases in household consumption expenditure were responsible for a relatively high growth of energy consumption. Switching to consumption of less energy intensive products and decrease in energy intensities of products in 1990s contributed substantially to reduce the increase in the total household energy requirement. A future Korean study should apply a hybrid method as to reduce errors occurred by using uniform (average) prices in constructing energy input-output tables and as to make energy intensities of different years more comparable. (author)

Operational Amplifer Integrator

NARCIS (Netherlands)

van Tuijl, Adrianus Johannes Maria

2003-01-01

An integrator circuit comprises an operational amplifier which has a transistor stage (1) with an input terminal (4) and an output terminal (3), a feedback capacitor (2) connected between the input terminal (4) and the output terminal (3), and a resistor (5) connected to the input terminal (4), and

ATCA-based ATLAS FTK input interface system

Energy Technology Data Exchange (ETDEWEB)

Okumura, Yasuyuki [Chicago U., EFI; Liu, Tiehui Ted [Fermilab; Olsen, Jamieson [Fermilab; Iizawa, Tomoya [Waseda U.; Mitani, Takashi [Waseda U.; Korikawa, Tomohiro [Waseda U.; Yorita, Kohei [Waseda U.; Annovi, Alberto [Frascati; Beretta, Matteo [Frascati; Gatta, Maurizio [Frascati; Sotiropoulou, C-L. [Aristotle U., Thessaloniki; Gkaitatzis, Stamatios [Aristotle U., Thessaloniki; Kordas, Konstantinos [Aristotle U., Thessaloniki; Kimura, Naoki [Aristotle U., Thessaloniki; Cremonesi, Matteo [Chicago U., EFI; Yin, Hang [Fermilab; Xu, Zijun [Peking U.

2015-04-27

The first stage of the ATLAS Fast TracKer (FTK) is an ATCA-based input interface system, where hits from the entire silicon tracker are clustered and organized into overlapping eta-phi trigger towers before being sent to the tracking engines. First, FTK Input Mezzanine cards receive hit data and perform clustering to reduce data volume. Then, the ATCA-based Data Formatter system will organize the trigger tower data, sharing data among boards over full mesh backplanes and optic fibers. The board and system level design concepts and implementation details, as well as the operation experiences from the FTK full-chain testing, will be presented.

ATCA-based ATLAS FTK input interface system

CERN Document Server

Okumura, Y; The ATLAS collaboration; Olsen, J; Iizawa, T; Mitani, T; Korikawa, T; Yorita, K; Annovi, A; Beretta, M; Gatta, M; Sotiropoulou, C; Gkaitatzis, S; Kordas, K; Kimura, N; Cremonesi, M; Yin, H; Xu, Z

2014-01-01

The first stage of the ATLAS Fast TracKer (FTK) is an ATCA-based input interface system, where hits from the entire silicon tracker must be clustered and organized into overlapping eta-phi trigger towers before being sent to the tracking processors. First, FTK Input Mezzanine cards receive hit data and perform clustering to reduce data volume. Then, the ATCA-based Data Formatter system will organize the trigger tower data, sharing data among boards over a full-mesh backplane. The board and system level performance studies and implementation details, as well as the operation experiences from the FTK full-chain testing, will be presented.

National Ignition Facility site requirements

International Nuclear Information System (INIS)

1996-07-01

The Site Requirements (SR) provide bases for identification of candidate host sites for the National Ignition Facility (NIF) and for the generation of data regarding potential actual locations for the facilities. The SR supplements the NIF Functional Requirements (FR) with information needed for preparation of responses to queries for input to HQ DOE site evaluation. The queries are to include both documents and explicit requirements for the potential host site responses. The Sr includes information extracted from the NIF FR (for convenience), data based on design approaches, and needs for physical and organization infrastructure for a fully operational NIF. The FR and SR describe requirements that may require new construction or may be met by use or modification of existing facilities. The SR do not establish requirements for NIF design or construction project planning. The SR document does not constitute an element of the NIF technical baseline

29 CFR 1910.126 - Additional requirements for special dipping and coating operations.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Additional requirements for special dipping and coating... Dipping and Coating Operations § 1910.126 Additional requirements for special dipping and coating... requirements apply to flow coating? (1) You must use a direct low-pressure pumping system or a 10-gallon (38 L...

5th Evian Workshop on LHC beam operation

CERN Document Server

Goddard, B; Dubourg, S; Evian 2014

2014-01-01

The principal aims of the workshop are to: • Suggest operational parameter ranges for re-commissioning and operation in 2015; • Establish re-commissioning requirements for beam based LHC systems; • Establish planning for re-commissioning 2015; • Revisit overall strategy for 2015 (bunch spacing, scrubbing, special runs, MD etc.); • Provide input to Chamonix 2014. Chair: Mike LAMONT Deputy Chairs: Malika MEDDAHI, Brennan GODDARD Editors of the Proceedings: Brennan GODDARD, Sylvia DUBOURG Informatics & infrastructure support: Pierre CHARRUE Workshop Secretary: Sylvia DUBOURG

Effect of different input management on weed composition, diversity and density of corn field

Directory of Open Access Journals (Sweden)

Surur Khoramdel

2016-04-01

Full Text Available In order to investigate the effects of input intensity on species diversity, composition and density of weeds in corn (Zea mays L., an experiment was conducted based on a randomized complete block design with three replications at the Agricultural Research Station, Ferdowsi University of Mashhad, Iran during the year 2009. Treatments included low input, medium input and high input systems. Low input received 30 tonha-1or 30 tonha-1 compost, zero tillage and hand weeding (twice. Medium input was based on 15 tonha-1 manure, 150 kgha-1 urea as chemical fertilizer, twice tillage operations and 2, 4-D (1.5 Lha-1, at five leaves emergence as an herbicide and hand weeding (once. High input received 300 kgha-1 urea, four tillage operations and Paraquat (2 Lha-1, after planting and 2, 4-D (1.5 Lha-1, at five leaves emergence. Manure and compost were applied in the planting time. Weed samplings were done in three stages (early, mid and late growing season. Results indicated that the highest and the lowest weed species diversity and density were observed in low input based on manure and high input systems, respectively. The highest range of weed relative density was obtained for black nightshade (Solanum nigrum with 9.09-75.00%. The highest number of species was observed in low input based on manure. Also, management practices affected weed dry matter and diversity indices. The highest and the lowest amounts of weed dry matter were observed in low input based on manure and high input systems, respectively. In the first, second and the third stages of sampling, the maximum and the minimum amounts of Margalef index were observed in low input based on manure (with 5.3, 5.4 and 3.3, respectively and high input systems (with 0.8, 2.3 and 2.6, respectively. In the first, second and the third stages of sampling, the highest and the lowest values of Shannon index were observed in low input based on manure (with 0.6, 0.7 and 0.5 respectively and high input (with 0

Historical basis for analog input setpoints, 241-AY and 241-AZ tank farm MICON automation system

International Nuclear Information System (INIS)

Bragg, D.A.

1997-01-01

This document describes the original basis for selection of the analog input setpoints for the MICON Automation System. In most cases the setpoints were based on vendor supplied information and design requirements. However, some setpoints were also established based on engineering judgment. These setpoints are subject to change as more experience with operation of the ventilation system is obtained. Revision 1 incorporates minor changes to ensure the document setpoints accurately reflect limits established in OSD-T-151-00019, Rev B-0

Advanced Neutron Sources: Plant Design Requirements

International Nuclear Information System (INIS)

1990-07-01

The Advanced Neutron Source (ANS) is a new, world class facility for research using hot, thermal, cold, and ultra-cold neutrons. At the heart of the facility is a 350-MW th , heavy water cooled and moderated reactor. The reactor is housed in a central reactor building, with supporting equipment located in an adjoining reactor support building. An array of cold neutron guides fans out into a large guide hall, housing about 30 neutron research stations. Office, laboratory, and shop facilities are included to provide a complete users facility. The ANS is scheduled to begin operation at the Oak Ridge National Laboratory at the end of the decade. This Plant Design Requirements document defines the plant-level requirements for the design, construction, and operation of the ANS. This document also defines and provides input to the individual System Design Description (SDD) documents. Together, this Plant Design Requirements document and the set of SDD documents will define and control the baseline configuration of the ANS

Reduced power processor requirements for the 30-cm diameter HG ion thruster

Science.gov (United States)

Rawlin, V. K.

1979-01-01

The characteristics of power processors strongly impact the overall performance and cost of electric propulsion systems. A program was initiated to evaluate simplifications of the thruster-power processor interface requirements. The power processor requirements are mission dependent with major differences arising for those missions which require a nearly constant thruster operating point (typical of geocentric and some inbound planetary missions) and those requiring operation over a large range of input power (such as outbound planetary missions). This paper describes the results of tests which have indicated that as many as seven of the twelve power supplies may be eliminated from the present Functional Model Power Processor used with 30-cm diameter Hg ion thrusters.

Laparotomy operative note template constructed through a modified Delphi method.

Science.gov (United States)

Moore, Lolonya; Churley-Strom, Ruth; Singal, Bonita; O'Leary, Sharon

2009-05-01

An operative note is indispensable to physician documentation and decision-making; however, there are no accepted standards for operative note content. Our aim was to use a modified Delphi consensus-building method to construct a uniform operative note template for laparotomy. Using Joint Commission on Accreditation of Healthcare Organizations requirements, literature review, and feedback from 15 medical malpractice defense attorneys, we compiled a draft operative note template of 31 elements. We surveyed 37 Association of Professor of Gynecology and Obstetrics/Solvay scholars asking for their input on inclusion of each item as essential content of the operative note. Two iterations of the survey were required to reach a predetermined 75% level of consensus. Nine elements were eliminated from the template: 6 original and 3 expert-suggested elements. We provide an operative note template that was compiled through a Delphi process.

Supplemental design requirements document solid waste operations complex

International Nuclear Information System (INIS)

Ocampo, V.P.; Boothe, G.F.; Broz, D.R.; Eaton, H.E.; Greager, T.M.; Huckfeldt, R.A.; Kooiker, S.L.; Lamberd, D.L.; Lang, L.L.; Myers, J.B.

1994-11-01

This document provides additional and supplemental information to the WHC-SD-W112-FDC-001, WHC-SD-W113-FDC-001, and WHC-SD-W100-FDC-001. It provides additional requirements for the design and summarizes Westinghouse Hanford Company key design guidance and establishes the technical baseline agreements to be used for definitive design common to the Solid Waste Operations Complex (SWOC) Facilities (Project W-112, Project W-113, and WRAP 2A)

Detailed requirements document for the Interactive Financial Management System (IFMS), volume 1

Science.gov (United States)

Dodson, D. B.

1975-01-01

The detailed requirements for phase 1 (online fund control, subauthorization accounting, and accounts receivable functional capabilities) of the Interactive Financial Management System (IFMS) are described. This includes information on the following: systems requirements, performance requirements, test requirements, and production implementation. Most of the work is centered on systems requirements, and includes discussions on the following processes: resources authority, allotment, primary work authorization, reimbursable order acceptance, purchase request, obligation, cost accrual, cost distribution, disbursement, subauthorization performance, travel, accounts receivable, payroll, property, edit table maintenance, end-of-year, backup input. Other subjects covered include: external systems interfaces, general inquiries, general report requirements, communication requirements, and miscellaneous. Subjects covered under performance requirements include: response time, processing volumes, system reliability, and accuracy. Under test requirements come test data sources, general test approach, and acceptance criteria. Under production implementation come data base establishment, operational stages, and operational requirements.

Smart mobility solution with multiple input Output interface.

Science.gov (United States)

Sethi, Aartika; Deb, Sujay; Ranjan, Prabhat; Sardar, Arghya

2017-07-01

Smart wheelchairs are commonly used to provide solution for mobility impairment. However their usage is limited primarily due to high cost owing from sensors required for giving input, lack of adaptability for different categories of input and limited functionality. In this paper we propose a smart mobility solution using smartphone with inbuilt sensors (accelerometer, camera and speaker) as an input interface. An Emotiv EPOC+ is also used for motor imagery based input control synced with facial expressions in cases of extreme disability. Apart from traction, additional functions like home security and automation are provided using Internet of Things (IoT) and web interfaces. Although preliminary, our results suggest that this system can be used as an integrated and efficient solution for people suffering from mobility impairment. The results also indicate a decent accuracy is obtained for the overall system.

Third order TRANSPORT with MAD [Methodical Accelerator Design] input

International Nuclear Information System (INIS)

Carey, D.C.

1988-01-01

This paper describes computer-aided design codes for particle accelerators. Among the topics discussed are: input beam description; parameters and algebraic expressions; the physical elements; beam lines; operations; and third-order transfer matrix

Review of FEWS NET Biophysical Monitoring Requirements

Science.gov (United States)

Ross, K. W.; Brown, Molly E.; Verdin, J.; Underwood, L. W.

2009-01-01

The Famine Early Warning System Network (FEWS NET) provides monitoring and early warning support to decision makers responsible for responding to famine and food insecurity. FEWS NET transforms satellite remote sensing data into rainfall and vegetation information that can be used by these decision makers. The National Aeronautics and Space Administration has recently funded activities to enhance remote sensing inputs to FEWS NET. To elicit Earth observation requirements, a professional review questionnaire was disseminated to FEWS NET expert end-users: it focused upon operational requirements to determine additional useful remote sensing data and; subsequently, beneficial FEWS NET biophysical supplementary inputs. The review was completed by over 40 experts from around the world, enabling a robust set of professional perspectives to be gathered and analyzed rapidly. Reviewers were asked to evaluate the relative importance of environmental variables and spatio-temporal requirements for Earth science data products, in particular for rainfall and vegetation products. The results showed that spatio-temporal resolution requirements are complex and need to vary according to place, time, and hazard: that high resolution remote sensing products continue to be in demand, and that rainfall and vegetation products were valued as data that provide actionable food security information.

Performance analysis of active damped small DC-link capacitor based drive for unbalanced input voltage supply

DEFF Research Database (Denmark)

Maheshwari, Ram Krishan; Munk-Nielsen, Stig

2011-01-01

A small DC-link capacitor based drive is presented in this paper. The drive shows negative impedance instability at operating points with high power load. A phase portrait is presented for input filter states which exhibit a limit cycle. When the drive is operated with unbalanced input supply...

New requirements to collect operational data that are essential for facility decommissioning

International Nuclear Information System (INIS)

Kristofova, K.; Valcuha, P.

2017-01-01

The paper describes the features of the first nuclear regulatory safety guide to be released by the Nuclear Regulatory Authority of the Slovak Republic (UJD SR) in field of decommissioning. This safety guide specifies requirements to collect those nuclear facility operational data that are essential for its decommissioning. Recommendations of international organisations as well as experience in selected countries are provided. The following operational data types necessary for decommissioning process are identified and analysed: design documentation including modifications and changes during operation, photo-documentation, operational events and material and radiological inventory of the nuclear facility. The guide establishes requirements for collection of the operational data that can be recorded in interconnected database modules. In addition, a structure of decommissioning database is proposed, representing material and radiological inventory of a nuclear facility. This inventory database forms a basis for planning of the decommissioning process. At last, the guide summarises recommendations for data collection, archiving and maintenance of database records and also their applications in safety documentation necessary for decommissioning of nuclear facilities in Slovakia. (authors)

Example of material accounting and verification of reprocessing input

International Nuclear Information System (INIS)

Koch, L.; Schoof, S.

1981-01-01

An example is described in this paper of material accounting at the reprocessing input point. Knowledge of the fuel history and chemical analyses of the spent fuel permitted concepts to be tested which have been developed for the determination of the input by the operator and for its verification by nuclear material safeguards with the intention of detecting a protracted as well as an abrupt diversion. Accuracies obtained for a material balance of a PWR fuel reprocessing campaign are given. 6 refs

Computerized operating cost model for industrial steam generation

Energy Technology Data Exchange (ETDEWEB)

Powers, T.D.

1983-02-01

Pending EPA regulations, establishing revised emission levels for industrial boilers are perceived to have an effect on the relative costs of steam production technologies. To aid in the comparison of competitive boiler technologies, the Steam Cost Code was developed which provides levelized steam costs reflecting the effects of a number of key steam cost parameters. The Steam Cost Code is a user interactive FORTRAN program designed to operate on a VAX computer system. The program requires the user to input a number of variables describing the design characteristics, capital costs, and operating conditions for a specific boiler system. Part of the input to the Steam Cost Code is the capital cost of the steam production system. The capital cost is obtained from a program called INDCEPT, developed by Oak Ridge National Laboratory under Department of Energy, Morgantown Energy Technology Center sponsorship.

Visualization of virtual slave manipulator using the master input device

International Nuclear Information System (INIS)

Kim, S. H.; Song, T. K.; Lee, J. Y.; Yoon, J. S.

2003-01-01

To handle the high level radioactive materials such a spent fuel, the Master-Slave Manipulators (MSM) are widely used as a remote handling device in nuclear facilities such as the hot cell with sealed and shielded space. In this paper, the Digital Mockup which simulates the remote operation of the Advanced Conditioning Process(ACP) is developed. Also, the workspace and the motion of the slave manipulator, as well as, the remote operation task should be analyzed. The process equipment of ACP and Maintenance/Handling Device are drawn in 3D CAD models using IGRIP. Modeling device of manipulator is assigned with various mobiles attributes such as a relative position, kinematics constraints, and a range of mobility. The 3D graphic simulator using the external input device of space ball displays the movement of manipulator. To connect the external input device to the graphic simulator, the interface program of external input device with 6 DOF is deigned using the Low Level Tele-operation Interface (LLTI). The experimental result shows that the developed simulation system gives much-improved human interface characteristics and shows satisfactory response characteristics in terms of synchronization speed. This should be useful for the development of work's education system in the virtual environment

Development of NUPREP PC Version and Input Structures for NUCIRC Single Channel Analyses

Energy Technology Data Exchange (ETDEWEB)

Yoon, Churl; Jun, Ji Su; Park, Joo Hwan

2007-12-15

The input file for a steady-state thermal-hydraulic code NUCIRC consists of common channel input data and specific channel input data in a case of single channel analysis. Even when all the data is ready for the 380 channels' single channel analyses, it takes long time and requires enormous effort to compose an input file by hand-editing. The automatic pre-processor for this tedious job is a NUPREP code. In this study, a NUPREP PC version has been developed from the source list in the program manual of NUCIRC-MOD2.000 that is imported in a form of an execution file. In this procedure, some errors found in PC executions and lost statements are fixed accordingly. It is confirmed that the developed NUPREP code produces input file correctly for the CANDU-6 single channel analysis. Additionally, the NUCIRC input structure and data format are summarized for a single channel analysis and the input CARDs required for the creep information of aged channels are listed.

Robotics control using isolated word recognition of voice input

Science.gov (United States)

Weiner, J. M.

1977-01-01

A speech input/output system is presented that can be used to communicate with a task oriented system. Human speech commands and synthesized voice output extend conventional information exchange capabilities between man and machine by utilizing audio input and output channels. The speech input facility is comprised of a hardware feature extractor and a microprocessor implemented isolated word or phrase recognition system. The recognizer offers a medium sized (100 commands), syntactically constrained vocabulary, and exhibits close to real time performance. The major portion of the recognition processing required is accomplished through software, minimizing the complexity of the hardware feature extractor.

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

Documentation of compliance with the energy performance regulations at the end of the detailed design phase is mandatory for building owners in Denmark. Therefore, besides multidisciplinary input, the building design process requires various iterative analyses, so that the optimal solutions can...... be identified amongst multiple alternatives. However, meeting performance criteria is often associated with manual data inputs and retroactive modifications of the design. Due to poor interoperability between the authoring tools and the compliance check program, the processes are redundant and inefficient...... from building geometry created in Autodesk Revit and its translation to input for compliance check analysis....

Safety requirements to the operation of hydropower plants; Sicherheit beim Betrieb von Wasserkraftwerken

Energy Technology Data Exchange (ETDEWEB)

Lux, Reinhard [Berufsgenossenschaft Energie Textil Elektro Medienerzeugnisse (BG ETEM), Koeln (Germany)

2011-07-01

Employers have to take into account various safety and health requirements relating to the design, construction, operation and maintenance of hydropower plants. Especially the diversity of the hydropower plant components requires the consideration of different safety and health aspects. In 2011 the ''Fachausschuss Elektrotechnik'' (expert committee electro-technics) of the institution for statutory accident insurance and prevention presented a new ''BG-Information'' dealing with ''Safe methods operating hydropower plants''. The following article gives an introduction into the conception and the essential requirements of this new BG-Information. (orig.)

78 FR 46799 - Use of Market Economy Input Prices in Nonmarket Economy Proceedings

Science.gov (United States)

2013-08-02

...The Department of Commerce (``Department'') is modifying its regulation which states that the Department normally will use the price that a nonmarket economy (``NME'') producer pays to a market economy supplier when a factor of production is purchased from a market economy supplier and paid for in market economy currency, in the calculation of normal value (``NV'') in antidumping proceedings involving NME countries. The rule establishes a requirement that the input at issue be produced in one or more market economy countries, and a revised threshold requiring that ``substantially all'' (i.e., 85 percent) of an input be purchased from one or more market economy suppliers before the Department uses the purchase price paid to value the entire factor of production. The Department is making this change because it finds that a market economy input price is not the best available information for valuing all purchases of that input when market economy purchases of an input do not account for substantially all purchases of the input.

High Input Voltage, Silicon Carbide Power Processing Unit Performance Demonstration

Science.gov (United States)

Bozak, Karin E.; Pinero, Luis R.; Scheidegger, Robert J.; Aulisio, Michael V.; Gonzalez, Marcelo C.; Birchenough, Arthur G.

2015-01-01

A silicon carbide brassboard power processing unit has been developed by the NASA Glenn Research Center in Cleveland, Ohio. The power processing unit operates from two sources: a nominal 300 Volt high voltage input bus and a nominal 28 Volt low voltage input bus. The design of the power processing unit includes four low voltage, low power auxiliary supplies, and two parallel 7.5 kilowatt (kW) discharge power supplies that are capable of providing up to 15 kilowatts of total power at 300 to 500 Volts (V) to the thruster. Additionally, the unit contains a housekeeping supply, high voltage input filter, low voltage input filter, and master control board, such that the complete brassboard unit is capable of operating a 12.5 kilowatt Hall effect thruster. The performance of the unit was characterized under both ambient and thermal vacuum test conditions, and the results demonstrate exceptional performance with full power efficiencies exceeding 97%. The unit was also tested with a 12.5kW Hall effect thruster to verify compatibility and output filter specifications. With space-qualified silicon carbide or similar high voltage, high efficiency power devices, this would provide a design solution to address the need for high power electric propulsion systems.

Operating characteristics of a three-stage Stirling pulse tube cryocooler operating around 5 K

Science.gov (United States)

Qiu, L. M.; Cao, Q.; Zhi, X. Q.; Han, L.; Gan, Z. H.; Yu, Y. B.; Liu, Y.; Zhang, X. J.; Pfotenhauer, J. M.

2012-07-01

A Stirling pulse tube cryocooler (SPTC) operating at the liquid-helium temperatures represents an excellent prospect for satisfying the requirements of space applications because of its compactness, high efficiency and reliability. However, the working mechanism of a 4 K SPTC is more complicated than that of the Gifford McMahon (GM) PTC that operates at the relatively low frequency of 1-2 Hz, and has not yet been well understood. In this study, the primary operating parameters, including frequency, charge pressure, input power and precooling temperature, are systematically investigated in a home-developed separate three-stage SPTC. The investigation demonstrates that the frequency and precooling temperature are closely coupled via phase shift. In order to improve the cooling capacity it is important to lower the frequency and the precooling temperature simultaneously. In contrast to the behavior predicted by previous studies, the pressure dependence of the gas properties results in an optimized pressure that decreases significantly as the temperature is lowered. The third stage reaches a lowest temperature of 4.97 K at 29.9 Hz and 0.91 MPa. A cooling power of 25 mW is measured at 6.0 K. The precooling temperature is 23.7 K and the input power is 100 W.

TASS/SMR Code Topical Report for SMART Plant, Vol II: User's Guide and Input Requirement

International Nuclear Information System (INIS)

Kim, See Darl; Kim, Soo Hyoung; Kim, Hyung Rae

2008-10-01

The TASS/SMR code has been developed with domestic technologies for the safety analysis of the SMART plant which is an integral type pressurized water reactor. It can be applied to the analysis of design basis accidents including non-LOCA (loss of coolant accident) and LOCA of the SMART plant. The TASS/SMR code can be applied to any plant regardless of the structural characteristics of a reactor since the code solves the same governing equations for both the primary and secondary system. The code has been developed to meet the requirements of the safety analysis code. This report describes the overall structure of the TASS/SMR, input processing, and the processes of a steady state and transient calculations. In addition, basic differential equations, finite difference equations, state relationships, and constitutive models are described in the report. First, the conservation equations, a discretization process for numerical analysis, search method for state relationship are described. Then, a core power model, heat transfer models, physical models for various components, and control and trip models are explained

Development of a Math Input Interface with Flick Operation for Mobile Devices

Science.gov (United States)

Nakamura, Yasuyuki; Nakahara, Takahiro

2016-01-01

Developing online test environments for e-learning for mobile devices will be useful to increase drill practice opportunities. In order to provide a drill practice environment for calculus using an online math test system, such as STACK, we develop a flickable math input interface that can be easily used on mobile devices. The number of taps…

Space shuttle orbiter guidance, naviagation and control software functional requirements: Horizontal flight operations

Science.gov (United States)

1972-01-01

The shuttle GN&C software functions for horizontal flight operations are defined. Software functional requirements are grouped into two categories: first horizontal flight requirements and full mission horizontal flight requirements. The document privides the intial step in the shuttle GN&C software design process. It also serves as a management tool to identify analyses which are required to define requirements.

78 FR 53025 - Pilot Certification and Qualification Requirements for Air Carrier Operations; Correction

Science.gov (United States)

2013-08-28

...-0100; Amdt. No. 141-17A] RIN 2120-AJ67 Pilot Certification and Qualification Requirements for Air... regulations to create new certification and qualification requirements for pilots in air carrier operations..., the FAA published a final rule entitled, ``Pilot Certification and Qualification Requirements for Air...

HALE UAS Concept of Operations. Version 3.0

Science.gov (United States)

2006-01-01

This document is a system level Concept of Operations (CONOPS) from the perspective of future High Altitude Long Endurance (HALE) Unmanned Aircraft Systems (UAS) service providers and National Airspace System (NAS) users. It describes current systems (existing UAS), describes HALE UAS functions and operations to be performed (via sample missions), and offers insight into the user s environment (i.e., the UAS as a system of systems). It is intended to be a source document for NAS UAS operational requirements, and provides a construct for government agencies to use in guiding their regulatory decisions, architecture requirements, and investment strategies. Although it does not describe the technical capabilities of a specific HALE UAS system (which do, and will vary widely), it is intended to aid in requirements capture and to be used as input to the functional requirements and analysis process. The document provides a basis for development of functional requirements and operational guidelines to achieve unrestricted access into the NAS. This document is an FY06 update to the FY05 Access 5 Project-approved Concept of Operations document previously published in the Public Domain on the Access 5 open website. This version is recommended to be approved for public release also. The updates are a reorganization of materials from the previous version with the addition of an updated set of operational requirements, inclusion of sample mission scenarios, and identification of roles and responsibilities of interfaces within flight phases.

Premedication with oral Dextromethorphan reduces intra-operative Morphine requirement

Directory of Open Access Journals (Sweden)

R Talakoub

2005-09-01

Full Text Available Background: Intra-operative pain has adverse effects on hemodynamic parameters. Due to complications of opioids for pain relief, using non-opioids medication is preferred. The purpose of this study was to investigate the effect of oral dextrometorphan premedication on intra-operative Morphine requirement. Methods: After approval of the Ethics committee and informed consent, 40 adult patients who stand in American Society of Anesthesiologists Physical Status I and II, under general anesthesia for elective laparatomy were selected and classified in two equal groups randomly. In group A, oral dextromethorphan (60mg was administered at 10 PM and 6 AM preoperatively. In group B, placebo (dextrose was administered. After induction of general anesthesia and before skin incision, intravenous morphine (0.01 mg/kg was administered. During surgery, when systolic blood pressure or heart rate was increased more than 20% of the preoperative baseline, 0.01 mg/kg morphine was administered. At the end of surgery, the totally prescribed morphine (mg/kg and maximal increase in systolic, diastolic, mean arterial blood pressure and heart rate relative to the baseline values were calculated and statistically compared with student’s t-test. Results: The mean dose of administered morphine during surgery was significantly less in group A than group B (P<0.0001. Also, Maximal increase in systolic, diastolic and mean arterial blood pressure was significantly less in group A (p<0.003, p<0.004, p<0.0001, respectively. There was no significant difference in maximal heart rate increase between two groups (p<0.114. Conclusion: Oral dextromethorphan premedication may decrease intra-operative morphine requirement and reduce maximal increase in systolic and mean arterial blood pressure during surgery. Key words: Dextromethorphan, Morphine, Intra-operative, Premedication Hemodynamic

Summary of astronaut inputs on automation and robotics for Space Station Freedom

Science.gov (United States)

Weeks, David J.

1990-01-01

Astronauts and payload specialists present specific recommendations in the form of an overview that relate to the use of automation and robotics on the Space Station Freedom. The inputs are based on on-orbit operations experience, time requirements for crews, and similar crew-specific knowledge that address the impacts of automation and robotics on productivity. Interview techniques and specific questionnaire results are listed, and the majority of the responses indicate that incorporating automation and robotics to some extent and with human backup can improve productivity. Specific support is found for the use of advanced automation and EVA robotics on the Space Station Freedom and for the use of advanced automation on ground-based stations. Ground-based control of in-flight robotics is required, and Space Station activities and crew tasks should be analyzed to assess the systems engineering approach for incorporating automation and robotics.

33 CFR 88.09 - Temporary exemption from light and shape requirements when operating under bridges.

Science.gov (United States)

2010-07-01

... and shape requirements when operating under bridges. 88.09 Section 88.09 Navigation and Navigable... Temporary exemption from light and shape requirements when operating under bridges. A vessel's navigation lights and shapes may be lowered if necessary to pass under a bridge. ...

Key Technologies in the Context of Future Networks: Operational and Management Requirements

Directory of Open Access Journals (Sweden)

Lorena Isabel Barona López

2016-12-01

Full Text Available The concept of Future Networks is based on the premise that current infrastructures require enhanced control, service customization, self-organization and self-management capabilities to meet the new needs in a connected society, especially of mobile users. In order to provide a high-performance mobile system, three main fields must be improved: radio, network, and operation and management. In particular, operation and management capabilities are intended to enable business agility and operational sustainability, where the addition of new services does not imply an excessive increase in capital or operational expenditures. In this context, a set of key-enabled technologies have emerged in order to aid in this field. Concepts such as Software Defined Network (SDN, Network Function Virtualization (NFV and Self-Organized Networks (SON are pushing traditional systems towards the next 5G network generation.This paper presents an overview of the current status of these promising technologies and ongoing works to fulfill the operational and management requirements of mobile infrastructures. This work also details the use cases and the challenges, taking into account not only SDN, NFV, cloud computing and SON but also other paradigms.

Space Vector Modulation for an Indirect Matrix Converter with Improved Input Power Factor

Directory of Open Access Journals (Sweden)

Nguyen Dinh Tuyen

2017-04-01

Full Text Available Pulse width modulation strategies have been developed for indirect matrix converters (IMCs in order to improve their performance. In indirect matrix converters, the LC input filter is used to remove input current harmonics and electromagnetic interference problems. Unfortunately, due to the existence of the input filter, the input power factor is diminished, especially during operation at low voltage outputs. In this paper, a new space vector modulation (SVM is proposed to compensate for the input power factor of the indirect matrix converter. Both computer simulation and experimental studies through hardware implementation were performed to verify the effectiveness of the proposed modulation strategy.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements

International Nuclear Information System (INIS)

2012-01-01

On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Measuring Input Thresholds on an Existing Board

Science.gov (United States)

Kuperman, Igor; Gutrich, Daniel G.; Berkun, Andrew C.

2011-01-01

A critical PECL (positive emitter-coupled logic) interface to Xilinx interface needed to be changed on an existing flight board. The new Xilinx input interface used a CMOS (complementary metal-oxide semiconductor) type of input, and the driver could meet its thresholds typically, but not in worst-case, according to the data sheet. The previous interface had been based on comparison with an external reference, but the CMOS input is based on comparison with an internal divider from the power supply. A way to measure what the exact input threshold was for this device for 64 inputs on a flight board was needed. The measurement technique allowed an accurate measurement of the voltage required to switch a Xilinx input from high to low for each of the 64 lines, while only probing two of them. Directly driving an external voltage was considered too risky, and tests done on any other unit could not be used to qualify the flight board. The two lines directly probed gave an absolute voltage threshold calibration, while data collected on the remaining 62 lines without probing gave relative measurements that could be used to identify any outliers. The PECL interface was forced to a long-period square wave by driving a saturated square wave into the ADC (analog to digital converter). The active pull-down circuit was turned off, causing each line to rise rapidly and fall slowly according to the input s weak pull-down circuitry. The fall time shows up as a change in the pulse width of the signal ready by the Xilinx. This change in pulse width is a function of capacitance, pulldown current, and input threshold. Capacitance was known from the different trace lengths, plus a gate input capacitance, which is the same for all inputs. The pull-down current is the same for all inputs including the two that are probed directly. The data was combined, and the Excel solver tool was used to find input thresholds for the 62 lines. This was repeated over different supply voltages and

40 CFR 62.15145 - What are the operating practice requirements for my municipal waste combustion unit?

Science.gov (United States)

2010-07-01

... requirements for my municipal waste combustion unit? 62.15145 Section 62.15145 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Good Combustion Practices: Operating Requirements § 62.15145 What are the operating practice requirements for my municipal waste combustion unit? (a) You...

Incorporating uncertainty in RADTRAN 6.0 input files.

Energy Technology Data Exchange (ETDEWEB)

Dennis, Matthew L.; Weiner, Ruth F.; Heames, Terence John (Alion Science and Technology)

2010-02-01

Uncertainty may be introduced into RADTRAN analyses by distributing input parameters. The MELCOR Uncertainty Engine (Gauntt and Erickson, 2004) has been adapted for use in RADTRAN to determine the parameter shape and minimum and maximum of the distribution, to sample on the distribution, and to create an appropriate RADTRAN batch file. Coupling input parameters is not possible in this initial application. It is recommended that the analyst be very familiar with RADTRAN and able to edit or create a RADTRAN input file using a text editor before implementing the RADTRAN Uncertainty Analysis Module. Installation of the MELCOR Uncertainty Engine is required for incorporation of uncertainty into RADTRAN. Gauntt and Erickson (2004) provides installation instructions as well as a description and user guide for the uncertainty engine.

Power system reliability impacts of wind generation and operational reserve requirements

Directory of Open Access Journals (Sweden)

Esteban Gil

2015-06-01

Full Text Available Due to its variability, wind generation integration presents a significant challenge to power system operators in order to maintain adequate reliability levels while ensuring least cost operation. This paper explores the trade-off between the benefits associated to a higher wind penetration and the additional operational reserve requirements that they impose. Such exploration is valued in terms of its effect on power system reliability, measured as an amount of unserved energy. The paper also focuses on how changing the Value of Lost Load (VoLL can be used to attain different reliability targets, and how wind power penetration and the diversity of the wind energy resource will impact quality of supply (in terms of instances of unserved energy. The evaluation of different penetrations of wind power generation, different wind speed profiles, wind resource diversity, and different operational reserve requirements, is conducted on the Chilean Northern Interconnected System (SING using statistical modeling of wind speed time series and computer simulation through a 24-hour ahead unit commitment algorithm and a Monte Carlo simulation scheme. Results for the SING suggest that while wind generation can significantly reduce generation costs, it can also imply higher security costs to reach acceptable reliability levels.

High-Voltage-Input Level Translator Using Standard CMOS

Science.gov (United States)

Yager, Jeremy A.; Mojarradi, Mohammad M.; Vo, Tuan A.; Blalock, Benjamin J.

2011-01-01

proposed integrated circuit would translate (1) a pair of input signals having a low differential potential and a possibly high common-mode potential into (2) a pair of output signals having the same low differential potential and a low common-mode potential. As used here, "low" and "high" refer to potentials that are, respectively, below or above the nominal supply potential (3.3 V) at which standard complementary metal oxide/semiconductor (CMOS) integrated circuits are designed to operate. The input common-mode potential could lie between 0 and 10 V; the output common-mode potential would be 2 V. This translation would make it possible to process the pair of signals by use of standard 3.3-V CMOS analog and/or mixed-signal (analog and digital) circuitry on the same integrated-circuit chip. A schematic of the circuit is shown in the figure. Standard 3.3-V CMOS circuitry cannot withstand input potentials greater than about 4 V. However, there are many applications that involve low-differential-potential, high-common-mode-potential input signal pairs and in which standard 3.3-V CMOS circuitry, which is relatively inexpensive, would be the most appropriate circuitry for performing other functions on the integrated-circuit chip that handles the high-potential input signals. Thus, there is a need to combine high-voltage input circuitry with standard low-voltage CMOS circuitry on the same integrated-circuit chip. The proposed circuit would satisfy this need. In the proposed circuit, the input signals would be coupled into both a level-shifting pair and a common-mode-sensing pair of CMOS transistors. The output of the level-shifting pair would be fed as input to a differential pair of transistors. The resulting differential current output would pass through six standoff transistors to be mirrored into an output branch by four heterojunction bipolar transistors. The mirrored differential current would be converted back to potential by a pair of diode-connected transistors

PC-based input/output controllers from a VME perspective

International Nuclear Information System (INIS)

Hill, J.O.

1999-01-01

The Experimental Physics and Industrial Control System (EPICS) has been widely adopted in the accelerator community. Although EPICS is available on many platforms, the majority of sites have deployed VME- or VXI-based input output controllers running the vxWorks real time operating system. Recently, a hybrid approach using vxWorks on both PC and traditional platforms is being implemented at LANL. To illustrate these developments the author compares his recent experience deploying PC-based EPICS input output controllers with experience deploying similar systems based on traditional EPICS platforms

Optimal Input Strategy for Plug and Play Process Control Systems

DEFF Research Database (Denmark)

Kragelund, Martin Nygaard; Leth, John-Josef; Wisniewski, Rafal

2010-01-01

This paper considers the problem of optimal operation of a plant, which goal is to maintain production at minimum cost. The system considered in this work consists of a joined plant and redundant input systems. It is assumed that each input system contributes to a flow of goods into the joined pa...... the performance of the plant. The results are applied to a coal fired power plant where an additional new fuel system, gas, becomes available....

Safety of Nuclear Power Plants: Commissioning and Operation. Specific Safety Requirements (French Edition)

International Nuclear Information System (INIS)

2016-01-01

This publication describes the requirements to be met to ensure the safe operation of nuclear power plants. It takes into account developments in areas such as long term operation of nuclear power plants, plant ageing, periodic safety review, probabilistic safety analysis and risk informed decision making processes. In addition, the requirements are governed by, and must apply, the safety objective and safety principles that are established in the IAEA Safety Standards Series No. SF-1, Fundamental Safety Principles. A review of Safety Requirements publications was commenced in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan. The review revealed no significant areas of weakness and resulted in just a small set of amendments to strengthen the requirements and facilitate their implementation, which are contained in the present publication.

The effect of harmeful elements in production of iron in relation to input and output material balance

Directory of Open Access Journals (Sweden)

P. Besta

2012-07-01

Full Text Available The main objectives of blast-furnace operators include maximum production of pig iron of required chemical composition at minimal cost. This can be ensured only in case of quality raw material basis and trouble-free operation of blast-furnace. Both parameters are influenced by the concentration of undesirable elements. The negative elements contained in the blast-furnace raw materials cause many technological problems in the sintering as well as in the blast-furnace process. These are mainly heavy metals and alkaline carbonates. The article deals with the analysis of material balance of zinc and selected alkaline carbonates contents in the input raw materials and output products of the blast-furnace.

Nuclear safety requirements for operation licensing of Egyptian research reactors

International Nuclear Information System (INIS)

Ahmed, E.E.M.; Rahman, F.A.

2000-01-01

From the view of responsibility for health and nuclear safety, this work creates a framework for the application of nuclear regulatory rules to ensure safe operation for the sake of obtaining or maintaining operation licensing for nuclear research reactors. It has been performed according to the recommendations of the IAEA for research reactor safety regulations which clearly states that the scope of the application should include all research reactors being designed, constructed, commissioned, operated, modified or decommissioned. From that concept, the present work establishes a model structure and a computer logic program for a regulatory licensing system (RLS code). It applies both the regulatory inspection and enforcement regulatory rules on the different licensing process stages. The present established RLS code is then applied to the Egyptian Research Reactors, namely; the first ET-RR-1, which was constructed and still operating since 1961, and the second MPR research reactor (ET-RR-2) which is now in the preliminary operation stage. The results showed that for the ET-RR-1 reactor, all operational activities, including maintenance, in-service inspection, renewal, modification and experiments should meet the appropriate regulatory compliance action program. Also, the results showed that for the new MPR research reactor (ET-RR-2), all commissioning and operational stages should also meet the regulatory inspection and enforcement action program of the operational licensing safety requirements. (author)

The role of the control room operator

International Nuclear Information System (INIS)

Williams, M.C.

A control room operator at an Ontario Hydro nuclear power plant operates a reactor-turbine unit according to approved procedures within imposed constraints to meet the objectives of the organization. A number of operating and administrative tasks make up this role. Control room operators spend approximately six percent of their time physically operating equipment exclusive of upset conditions, and another one percent operating in upset conditions. Testing occupies five percent of an operator's time. Operators must be trained to recognize the entire spectrum of inputs available to them and use them all effectively. Any change in system or unit state is always made according to an approved procedure. Extensive training is required; operators must be taught and pracised in what to do, and must know the reasons behind their actions. They are expected to memorize emergency procedures, to know when to consult operating procedures, and to have sufficient understanding and practice to perform these procedures reliably

FED, Geometry Input Generator for Program TRUMP

International Nuclear Information System (INIS)

Schauer, D.A.; Elrod, D.C.

1996-01-01

1 - Description of program or function: FED reduces the effort required to obtain the necessary geometric input for problems which are to be solved using the heat-transfer code, TRUMP (NESC 771). TRUMP calculates transient and steady-state temperature distributions in multidimensional systems. FED can properly zone any body of revolution in one, or three dimensions. 2 - Method of solution: The region of interest must first be divided into areas which may consist of a common material. The boundaries of these areas are the required FED input. Each area is subdivided into volume nodes, and the geometrical properties are calculated. Finally, FED connects the adjacent nodes to one another, using the proper surface area, interface distance, and, if specified, radiation form factor and interface conductance. 3 - Restrictions on the complexity of the problem: Rectangular bodies can only be approximated by using a very large radius of revolution compared to the total radial thickness and by considering only a small angular segment in the circumferential direction

Expert systems to assist plant operation

International Nuclear Information System (INIS)

Matsumoto, Yoshihiro; Mori, Nobuyuki; Wada, Norio

1985-01-01

Large-scale real-time process control systems, such as those for electric power dispatching, large thermal and nuclear power stations, steel mill plants and manufacturing automation systems, need expert systems to assist operator's decision. The expert systems newly developed to fulfill the requirement are founded on OKBS (object oriented knowledge based system). OKBS provides various object types: fuzzy logic type, production rule type, frame type, state transition type, abstract data type and input/output transformation type. (author)

Efficient round-robin multicast scheduling for input-queued switches

DEFF Research Database (Denmark)

Rasmussen, Anders; Yu, Hao; Ruepp, Sarah Renée

2014-01-01

The input-queued (IQ) switch architecture is favoured for designing multicast high-speed switches because of its scalability and low implementation complexity. However, using the first-in-first-out (FIFO) queueing discipline at each input of the switch may cause the head-of-line (HOL) blocking...... problem. Using a separate queue for each output port at an input to reduce the HOL blocking, that is, the virtual output queuing discipline, increases the implementation complexity, which limits the scalability. Given the increasing link speed and network capacity, a low-complexity yet efficient multicast...... by means of queue look-ahead. Simulation results demonstrate that this FIFO-based IQ multicast architecture is able to achieve significant improvements in terms of multicast latency requirements by searching through a small number of cells beyond the HOL cells in the input queues. Furthermore, hardware...

Small leak detection requirements for SNR-300 steam generator operation

International Nuclear Information System (INIS)

Dumm, K.

1975-01-01

The leak detection philosophy of the SNR-300 steam generators is described. Due to operational demands small leaks have already to be detectable at a stage where secondary tube damage has not yet occurred. The requirements on a leak detection instrument are developed and the instrument itself is described. (author)

33 CFR 151.67 - Operating requirements: Discharge of plastic prohibited.

Science.gov (United States)

2010-07-01

... of plastic prohibited. 151.67 Section 151.67 Navigation and Navigable Waters COAST GUARD, DEPARTMENT... Sewage § 151.67 Operating requirements: Discharge of plastic prohibited. No person on board any ship may discharge into the sea, or into the navigable waters of the United States, plastic or garbage mixed with...

Small leak detection requirements for SNR-300 steam generator operation

Energy Technology Data Exchange (ETDEWEB)

Dumm, K

1975-07-01

The leak detection philosophy of the SNR-300 steam generators is described. Due to operational demands small leaks have already to be detectable at a stage where secondary tube damage has not yet occurred. The requirements on a leak detection instrument are developed and the instrument itself is described. (author)

Model-based human reliability analysis: prospects and requirements

International Nuclear Information System (INIS)

Mosleh, A.; Chang, Y.H.

2004-01-01

Major limitations of the conventional methods for human reliability analysis (HRA), particularly those developed for operator response analysis in probabilistic safety assessments (PSA) of nuclear power plants, are summarized as a motivation for the need and a basis for developing requirements for the next generation HRA methods. It is argued that a model-based approach that provides explicit cognitive causal links between operator behaviors and directly or indirectly measurable causal factors should be at the core of the advanced methods. An example of such causal model is briefly reviewed, where due to the model complexity and input requirements can only be currently implemented in a dynamic PSA environment. The computer simulation code developed for this purpose is also described briefly, together with current limitations in the models, data, and the computer implementation

Data input from an analog-to-digital converter into the M-6000 computer

International Nuclear Information System (INIS)

Kalashnikov, A.M.; Sheremet'ev, A.K.

1978-01-01

A device for spectrometric data input from the ADC-4096 into the M-6000 computer memory operating in the information storage regime is described. The input device made on integrated circuits coordinates signal levels of the fast response analog-to-digital converter and computer with the help of resistors and inverters. Besides, the input forms a strobe to trigger an increment channel used to record information into the computer memory. The use of the input device permits to get rid of the intermediate information storage in the analyzer memory and ensures fast response of the devices

21 CFR 111.117 - What quality control operations are required for equipment, instruments, and controls?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for equipment, instruments, and controls? 111.117 Section 111.117 Food and Drugs FOOD AND DRUG ADMINISTRATION... and Process Control System: Requirements for Quality Control § 111.117 What quality control operations...

Important requirements for RF generators for Accelerator-Driven Transmutation Technologies (ADTT)

International Nuclear Information System (INIS)

Lynch, M.T.; Tallerico, P.J.; Lawrence, G.P.

1994-01-01

All Accelerator-Driven Transmutation applications require very large amounts of RF Power. For example, one version of a Plutonium burning system requires an 800-MeV, 80-mA, proton accelerator running at 100% duty factor. This accelerator requires approximately 110-MW of continuous RF power if one assumes only 10% reserve power for control of the accelerator fields. In fact, to minimize beam spill, the RF controls may need as much as 15 to 20% of reserve power. In addition, unlike an electron accelerator in which the beam is relativistic, a failed RF station can disturb the synchronism of the beam, possibly shutting down the entire accelerator. These issues and more lead to a set of requirements for the RF generators which are stringent, and in some cases, conflicting. In this paper, we will describe the issues and requirements, and outline a plan for RF generator development to meet the needs of the Accelerator-Driven Transmutation Technologies. The key issues which will be discussed include: operating efficiency, operating linearity, effect on the input power grid, bandwidth, gain, reliability, operating voltage, and operating current

21 CFR 111.120 - What quality control operations are required for components, packaging, and labels before use in...

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for..., OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for Quality Control § 111.120 What quality control operations are required for components, packaging, and...

The Use of Input-Output Control System Analysis for Sustainable Development of Multivariable Environmental Systems

Science.gov (United States)

Koliopoulos, T. C.; Koliopoulou, G.

2007-10-01

We present an input-output solution for simulating the associated behavior and optimized physical needs of an environmental system. The simulations and numerical analysis determined the accurate boundary loads and areas that were required to interact for the proper physical operation of a complicated environmental system. A case study was conducted to simulate the optimum balance of an environmental system based on an artificial intelligent multi-interacting input-output numerical scheme. The numerical results were focused on probable further environmental management techniques, with the objective of minimizing any risks and associated environmental impact to protect the quality of public health and the environment. Our conclusions allowed us to minimize the associated risks, focusing on probable cases in an emergency to protect the surrounded anthropogenic or natural environment. Therefore, the lining magnitude could be determined for any useful associated technical works to support the environmental system under examination, taking into account its particular boundary necessities and constraints.

Input Shaping to Reduce Solar Array Structural Vibrations

Science.gov (United States)

Doherty, Michael J.; Tolson, Robert J.

1998-01-01

Structural vibrations induced by actuators can be minimized using input shaping. Input shaping is a feedforward method in which actuator commands are convolved with shaping functions to yield a shaped set of commands. These commands are designed to perform the maneuver while minimizing the residual structural vibration. In this report, input shaping is extended to stepper motor actuators. As a demonstration, an input-shaping technique based on pole-zero cancellation was used to modify the Solar Array Drive Assembly (SADA) actuator commands for the Lewis satellite. A series of impulses were calculated as the ideal SADA output for vibration control. These impulses were then discretized for use by the SADA stepper motor actuator and simulated actuator outputs were used to calculate the structural response. The effectiveness of input shaping is limited by the accuracy of the knowledge of the modal frequencies. Assuming perfect knowledge resulted in significant vibration reduction. Errors of 10% in the modal frequencies caused notably higher levels of vibration. Controller robustness was improved by incorporating additional zeros in the shaping function. The additional zeros did not require increased performance from the actuator. Despite the identification errors, the resulting feedforward controller reduced residual vibrations to the level of the exactly modeled input shaper and well below the baseline cases. These results could be easily applied to many other vibration-sensitive applications involving stepper motor actuators.

Quantum theory of multiple-input-multiple-output Markovian feedback with diffusive measurements

International Nuclear Information System (INIS)

Chia, A.; Wiseman, H. M.

2011-01-01

Feedback control engineers have been interested in multiple-input-multiple-output (MIMO) extensions of single-input-single-output (SISO) results of various kinds due to its rich mathematical structure and practical applications. An outstanding problem in quantum feedback control is the extension of the SISO theory of Markovian feedback by Wiseman and Milburn [Phys. Rev. Lett. 70, 548 (1993)] to multiple inputs and multiple outputs. Here we generalize the SISO homodyne-mediated feedback theory to allow for multiple inputs, multiple outputs, and arbitrary diffusive quantum measurements. We thus obtain a MIMO framework which resembles the SISO theory and whose additional mathematical structure is highlighted by the extensive use of vector-operator algebra.

Resource allocation in shared spectrum access communications for operators with diverse service requirements

Science.gov (United States)

Kibria, Mirza Golam; Villardi, Gabriel Porto; Ishizu, Kentaro; Kojima, Fumihide; Yano, Hiroyuki

2016-12-01

In this paper, we study inter-operator spectrum sharing and intra-operator resource allocation in shared spectrum access communication systems and propose efficient dynamic solutions to address both inter-operator and intra-operator resource allocation optimization problems. For inter-operator spectrum sharing, we present two competent approaches, namely the subcarrier gain-based sharing and fragmentation-based sharing, which carry out fair and flexible allocation of the available shareable spectrum among the operators subject to certain well-defined sharing rules, traffic demands, and channel propagation characteristics. The subcarrier gain-based spectrum sharing scheme has been found to be more efficient in terms of achieved throughput. However, the fragmentation-based sharing is more attractive in terms of computational complexity. For intra-operator resource allocation, we consider resource allocation problem with users' dissimilar service requirements, where the operator supports users with delay constraint and non-delay constraint service requirements, simultaneously. This optimization problem is a mixed-integer non-linear programming problem and non-convex, which is computationally very expensive, and the complexity grows exponentially with the number of integer variables. We propose less-complex and efficient suboptimal solution based on formulating exact linearization, linear approximation, and convexification techniques for the non-linear and/or non-convex objective functions and constraints. Extensive simulation performance analysis has been carried out that validates the efficiency of the proposed solution.

An Exploration of Input Conditions for Virtual Teleportation

DEFF Research Database (Denmark)

Høeg, Emil Rosenlund; Ruder, Kevin Vignola; Nilsson, Niels Chr.

2017-01-01

This poster describes a within-groups study (n=17) comparing participants' experience of three different input conditions for instigating virtual teleportation (button clicking, physical jumping, and fist clenching). The results indicated that teleportation by clicking a button generally required...

40 CFR 267.198 - What are the general operating requirements for my tank systems?

Science.gov (United States)

2010-07-01

... FACILITIES OPERATING UNDER A STANDARDIZED PERMIT Tank Systems § 267.198 What are the general operating... 40 Protection of Environment 26 2010-07-01 2010-07-01 false What are the general operating requirements for my tank systems? 267.198 Section 267.198 Protection of Environment ENVIRONMENTAL PROTECTION...

Productivity and efficiency analysis of privatized hydroelectric generation with a sometimes free input

Science.gov (United States)

Halabi, Claudia Elizabeth

2000-10-01

In this paper I use a stochastic distance frontier approach to assess the performance of Chile's hydroelectric industry, which operates within a regulatory framework designed to achieve a competitive outcome. An occasionally free input, water, is the sole energy input. The econometric analysis indicates substantial technical and allocative inefficiencies as well as volatile productivity scores, due presumably to the volatility of the energy input. Some allocative inefficiencies have diminished dramatically as the time under deregulation has grown. The Lerner index suggests that firms in the industry enjoy some degree of market power, reflected by prices that exceed marginal costs. This market power is consistent with operation within a centralized dispatch center, as predicted by a strategic bidding model. I also find that run-of-river plants exhibit increasing returns to scale, while plants relying on dams show slightly diminishing returns. The shadow marginal cost for run-of-river plants is found to be close to zero. Substantial cost savings could be realized if firms in Chile's hydro-electric generation industry were to operate efficiently.

User's guide for MAGIC-Meteorologic and hydrologic genscn (generate scenarios) input converter

Science.gov (United States)

Ortel, Terry W.; Martin, Angel

2010-01-01

Meteorologic and hydrologic data used in watershed modeling studies are collected by various agencies and organizations, and stored in various formats. Data may be in a raw, un-processed format with little or no quality control, or may be checked for validity before being made available. Flood-simulation systems require data in near real-time so that adequate flood warnings can be made. Additionally, forecasted data are needed to operate flood-control structures to potentially mitigate flood damages. Because real-time data are of a provisional nature, missing data may need to be estimated for use in floodsimulation systems. The Meteorologic and Hydrologic GenScn (Generate Scenarios) Input Converter (MAGIC) can be used to convert data from selected formats into the Hydrologic Simulation System-Fortran hourly-observations format for input to a Watershed Data Management database, for use in hydrologic modeling studies. MAGIC also can reformat the data to the Full Equations model time-series format, for use in hydraulic modeling studies. Examples of the application of MAGIC for use in the flood-simulation system for Salt Creek in northeastern Illinois are presented in this report.

Harmonic-suppressed quadrature-input frequency divider for OFDM systems

International Nuclear Information System (INIS)

Fu Haipeng; Ren Junyan; Li Wei; Li Ning

2011-01-01

A fully balanced harmonic-suppressed quadrature-input frequency divider is proposed. The frequency divider improves the quadrature phase accuracy at the output by using both input I/Q signals. Compared with conventional dividers, the circuit achieves an output I/Q phase sequence that is independent of the input I/Q phase sequence. Moreover, the third harmonic is effectively suppressed by employing a double degeneration technique. The design is fabricated in TSMC 0.13-μm CMOS and operated at 1.2 V. While locked at 8.5 GHz, the proposed divider measures a maximum third harmonic rejection of 45 dB and a phase noise of −124 dBc/Hz at a 10 MHz offset. The circuit achieves a locking range of 15% while consuming a total current of 4.5 mA. (semiconductor integrated circuits)

TART input manual

International Nuclear Information System (INIS)

Kimlinger, J.R.; Plechaty, E.F.

1982-01-01

The TART code is a Monte Carlo neutron/photon transport code that is only on the CRAY computer. All the input cards for the TART code are listed, and definitions for all input parameters are given. The execution and limitations of the code are described, and input for two sample problems are given

Automatic stabilization of underwater robots in the time manipulation operations

International Nuclear Information System (INIS)

Filaretov, V.F.; Koval, E.V.

1994-01-01

When carrying out underwater technical works by means of an underwater vehicles having a manipulator it is desirable to perform manipulation operations in the regime of the underwater vehicle hovering above the object without durable and complicated operations up its rigid fixation. Underwater vehicle stabilization is achieved by compensation all the effects on the vehicle caused by the operating manipulator in water medium. This automatic stabilization is formed due to input of the required control signals into corresponding vehicle propellers proportional to calculated components of the generalized forces and moments. The propellers should form stops reacting against effects

Energy Systems Test Area (ESTA) Battery Test Operations User Test Planning Guide

Science.gov (United States)

Salinas, Michael

2012-01-01

Test process, milestones and inputs are unknowns to first-time users of the ESTA Battery Test Operations. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Time Series Modeling of Human Operator Dynamics in Manual Control Tasks

Science.gov (United States)

Biezad, D. J.; Schmidt, D. K.

1984-01-01

A time-series technique is presented for identifying the dynamic characteristics of the human operator in manual control tasks from relatively short records of experimental data. Control of system excitation signals used in the identification is not required. The approach is a multi-channel identification technique for modeling multi-input/multi-output situations. The method presented includes statistical tests for validity, is designed for digital computation, and yields estimates for the frequency response of the human operator. A comprehensive relative power analysis may also be performed for validated models. This method is applied to several sets of experimental data; the results are discussed and shown to compare favorably with previous research findings. New results are also presented for a multi-input task that was previously modeled to demonstrate the strengths of the method.

The use of virtual reality for preparation and implementation of JET remote handling operations

International Nuclear Information System (INIS)

Sanders, S.; Rolfe, A.C.

2003-01-01

The use of real time 3-D computer graphic models for preparation and support of remote handling operations on JET has been in use since the mid 1980s. A complete review has been undertaken of the functional requirements and benefits of VR for remote handling and a subsequent market survey of the present state-of-the-art of VR systems has resulted in the implementation of a new system for JET. The VR system is used in two discrete modes: in on-line mode the remote handling equipment Electro-mechanical hardware is connected to the VR system and provides input for the VR system to update a real time 3-D display of the equipment inside the torus. This mode supplements the video camera system and assists with camera control and warnings of impending or potential collisions. In Off-line mode the operator manipulates the VR system model with no connections to the remote handling equipment. This mode is used during preparation of RH operational strategies, checking of operational feasibility and operations procedures. Various VR systems were evaluated against a detailed technical specification that covered visualisation function and performance, user interface design and base model input/creation capabilities. The cheapest of those systems that satisfied the technical requirements was selected

40 CFR 60.1200 - What are the operating practice requirements for my municipal waste combustion unit?

Science.gov (United States)

2010-07-01

... requirements for my municipal waste combustion unit? 60.1200 Section 60.1200 Protection of Environment... SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is... Good Combustion Practices: Operating Requirements § 60.1200 What are the operating practice...

Plant operation monitoring method and device therefor

International Nuclear Information System (INIS)

Ando, Tsugio; Matsuki, Tsutomu.

1997-01-01

The present invention provides a method of and a device for monitoring the operation of a nuclear power plant during operation, which improves the safety and reliability of operation without increasing an operator's burden. Namely, a chief in charge orally instruct an operation to an operator upon the operation of a plant constituent equipment. The operator points the equipment and calls the name. Actual operation instruction for the equipment is inputted after confirmation by oral response. The voices of theses series of operation instruction/point-calling/response confirmation are taken into a voice recognition processing device. The processing device discriminates each of the person who calls, and discriminates the content of the calls and objective equipments to be operated. Then, the series of procedures and contents of the operation for the equipments previously disposed in the data base are compared with the order of inputted calls, discriminated contents and the objective equipments to be operated. If they are not agreed with each other, the operation instruction is blocked even if actual operation instructions are inputted. (I.S.)

Systematic Design Method and Experimental Validation of a 2-DOF Compliant Parallel Mechanism with Excellent Input and Output Decoupling Performances

Directory of Open Access Journals (Sweden)

Yao Jiang

2017-06-01

Full Text Available The output and input coupling characteristics of the compliant parallel mechanism (CPM bring difficulty in the motion control and challenge its high performance and operational safety. This paper presents a systematic design method for a 2-degrees-of-freedom (DOFs CPM with excellent decoupling performance. A symmetric kinematic structure can guarantee a CPM with a complete output decoupling characteristic; input coupling is reduced by resorting to a flexure-based decoupler. This work discusses the stiffness design requirement of the decoupler and proposes a compound flexure hinge as its basic structure. Analytical methods have been derived to assess the mechanical performances of the CPM in terms of input and output stiffness, motion stroke, input coupling degree, and natural frequency. The CPM’s geometric parameters were optimized to minimize the input coupling while ensuring key performance indicators at the same time. The optimized CPM’s performances were then evaluated by using a finite element analysis. Finally, a prototype was constructed and experimental validations were carried out to test the performance of the CPM and verify the effectiveness of the design method. The design procedure proposed in this paper is systematic and can be extended to design the CPMs with other types of motion.

78 FR 44873 - Pilot Certification and Qualification Requirements for Air Carrier Operations; Correction

Science.gov (United States)

2013-07-25

...-0100; Amdt. Nos. 61-130A] RIN 2120-AJ67 Pilot Certification and Qualification Requirements for Air... to create new certification and qualification requirements for pilots in air carrier operations. This... . SUPPLEMENTARY INFORMATION: Background On July 15, 2013, the FAA published a final rule entitled, ``Pilot...

Rise time reduction of thermal actuators operated in air and water through optimized pre-shaped open-loop driving

International Nuclear Information System (INIS)

Larsen, T; Doll, J C; Loizeau, F; Pruitt, B L; Hosseini, N; Fantner, G E; Peng, A W; Ricci, A J

2017-01-01

Electrothermal actuators have many advantages compared to other actuators used in micro-electro-mechanical systems (MEMS). They are simple to design, easy to fabricate and provide large displacements at low voltages. Low voltages enable less stringent passivation requirements for operation in liquid. Despite these advantages, thermal actuation is typically limited to a few kHz bandwidth when using step inputs due to its intrinsic thermal time constant. However, the use of pre-shaped input signals offers a route for reducing the rise time of these actuators by orders of magnitude. We started with an electrothermally actuated cantilever having an initial 10–90% rise time of 85 μ s in air and 234 μ s in water for a standard open-loop step input. We experimentally characterized the linearity and frequency response of the cantilever when operated in air and water, allowing us to obtain transfer functions for the two cases. We used these transfer functions, along with functions describing desired reduced rise-time system responses, to numerically simulate the required input signals. Using these pre-shaped input signals, we improved the open-loop 10–90% rise time from 85 μ s to 3 μ s in air and from 234 μ s to 5 μ s in water, an improvement by a factor of 28 and 47, respectively. Using this simple control strategy for MEMS electrothermal actuators makes them an attractive alternative to other high speed micromechanical actuators such as piezoelectric stacks or electrostatic comb structures which are more complex to design, fabricate, or operate. (paper)

Rise Time Reduction of Thermal Actuators Operated in Air and Water through Optimized Pre-Shaped Open-Loop Driving.

Science.gov (United States)

Larsen, T; Doll, J C; Loizeau, F; Hosseini, N; Peng, A W; Fantner, G; Ricci, A J; Pruitt, B L

2017-01-01

Electrothermal actuators have many advantages compared to other actuators used in Micro-Electro-Mechanical Systems (MEMS). They are simple to design, easy to fabricate and provide large displacements at low voltages. Low voltages enable less stringent passivation requirements for operation in liquid. Despite these advantages, thermal actuation is typically limited to a few kHz bandwidth when using step inputs due to its intrinsic thermal time constant. However, the use of pre-shaped input signals offers a route for reducing the rise time of these actuators by orders of magnitude. We started with an electrothermally actuated cantilever having an initial 10-90% rise time of 85 μs in air and 234 μs in water for a standard open-loop step input. We experimentally characterized the linearity and frequency response of the cantilever when operated in air and water, allowing us to obtain transfer functions for the two cases. We used these transfer functions, along with functions describing desired reduced rise-time system responses, to numerically simulate the required input signals. Using these pre-shaped input signals, we improved the open-loop 10-90% rise time from 85 μs to 3 μs in air and from 234 μs to 5 μs in water, an improvement by a factor of 28 and 47, respectively. Using this simple control strategy for MEMS electrothermal actuators makes them an attractive alternative to other high speed micromechanical actuators such as piezoelectric stacks or electrostatic comb structures which are more complex to design, fabricate, or operate.

20 CFR 726.1 - Statutory insurance requirements for coal mine operators.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Statutory insurance requirements for coal mine operators. 726.1 Section 726.1 Employees' Benefits EMPLOYMENT STANDARDS ADMINISTRATION, DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS...

21 CFR 111.113 - What quality control operations are required for a material review and disposition decision?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for a... Production and Process Control System: Requirements for Quality Control § 111.113 What quality control operations are required for a material review and disposition decision? (a) Quality control personnel must...

MRTouch: Adding Touch Input to Head-Mounted Mixed Reality.

Science.gov (United States)

Xiao, Robert; Schwarz, Julia; Throm, Nick; Wilson, Andrew D; Benko, Hrvoje

2018-04-01

We present MRTouch, a novel multitouch input solution for head-mounted mixed reality systems. Our system enables users to reach out and directly manipulate virtual interfaces affixed to surfaces in their environment, as though they were touchscreens. Touch input offers precise, tactile and comfortable user input, and naturally complements existing popular modalities, such as voice and hand gesture. Our research prototype combines both depth and infrared camera streams together with real-time detection and tracking of surface planes to enable robust finger-tracking even when both the hand and head are in motion. Our technique is implemented on a commercial Microsoft HoloLens without requiring any additional hardware nor any user or environmental calibration. Through our performance evaluation, we demonstrate high input accuracy with an average positional error of 5.4 mm and 95% button size of 16 mm, across 17 participants, 2 surface orientations and 4 surface materials. Finally, we demonstrate the potential of our technique to enable on-world touch interactions through 5 example applications.

The operational methane retrieval algorithm for TROPOMI

Directory of Open Access Journals (Sweden)

H. Hu

2016-11-01

Full Text Available This work presents the operational methane retrieval algorithm for the Sentinel 5 Precursor (S5P satellite and its performance tested on realistic ensembles of simulated measurements. The target product is the column-averaged dry air volume mixing ratio of methane (XCH4, which will be retrieved simultaneously with scattering properties of the atmosphere. The algorithm attempts to fit spectra observed by the shortwave and near-infrared channels of the TROPOspheric Monitoring Instrument (TROPOMI spectrometer aboard S5P.The sensitivity of the retrieval performance to atmospheric scattering properties, atmospheric input data and instrument calibration errors is evaluated. In addition, we investigate the effect of inhomogeneous slit illumination on the instrument spectral response function. Finally, we discuss the cloud filters to be used operationally and as backup.We show that the required accuracy and precision of  < 1 % for the XCH4 product are met for clear-sky measurements over land surfaces and after appropriate filtering of difficult scenes. The algorithm is very stable, having a convergence rate of 99 %. The forward model error is less than 1 % for about 95 % of the valid retrievals. Model errors in the input profile of water do not influence the retrieval outcome noticeably. The methane product is expected to meet the requirements if errors in input profiles of pressure and temperature remain below 0.3 % and 2 K, respectively. We further find that, of all instrument calibration errors investigated here, our retrievals are the most sensitive to an error in the instrument spectral response function of the shortwave infrared channel.

Some Normal Intuitionistic Fuzzy Heronian Mean Operators Using Hamacher Operation and Their Application

Directory of Open Access Journals (Sweden)

Guofang Zhang

2018-06-01

Full Text Available Hamacher operation is a generalization of the algebraic and Einstein operation and expresses a family of binary operation in the unit interval [0,1]. Heronian mean can deal with correlations of different criteria or input arguments and does not bring out repeated calculation. The normal intuitionistic fuzzy numbers (NIFNs can depict normal distribution information in practical decision making. A decision-making problem was researched under the NIFN environment in this study, and a new multi-criteria group decision-making (MCGDM approach is herein introduced on the basis of Hamacher operation. Firstly, according to Hamacher operation, some operational laws of NIFNs are presented. Secondly, it is noted that Heronian mean not only takes into account mutuality between the attribute values once, but also considers the correlation between input argument and itself. Therefore, in order to aggregate NIFN information, we developed some operators and studied their properties. These operators include Hamacher Heronian mean (NIFHHM, Hamacher weighted Heronian mean (NIFHWHM, Hamacher geometric Heronian mean (NIFHGHM, and Hamacher weighted geometric Heronian mean (NIFHWGHM. Furthermore, we applied the proposed operators to the MCGDM problem and developed a new MCGDM approach. The characteristics of this new approach are that: (1 it is suitable for making a decision under the NIFN environment and it is more reasonable for aggregating the normal distribution data; (2 it utilizes Hamacher operation to provide an effective and powerful MCGDM algorithm and to make more reliable and more flexible decisions under the NIFN circumstance; (3 it uses the Heronian mean operator to deal with interrelations between the attributes or input arguments, and it does not bring about repeated calculation. Therefore, the proposed method can describe the interaction of the different criteria or input arguments and offer some reasonable and reliable MCGDM aggregation operators

Development and validation of gui based input file generation code for relap

International Nuclear Information System (INIS)

Anwar, M.M.; Khan, A.A.; Chughati, I.R.; Chaudri, K.S.; Inyat, M.H.; Hayat, T.

2009-01-01

Reactor Excursion and Leak Analysis Program (RELAP) is a widely acceptable computer code for thermal hydraulics modeling of Nuclear Power Plants. It calculates thermal- hydraulic transients in water-cooled nuclear reactors by solving approximations to the one-dimensional, two-phase equations of hydraulics in an arbitrarily connected system of nodes. However, the preparation of input file and subsequent analysis of results in this code is a tedious task. The development of a Graphical User Interface (GUI) for preparation of the input file for RELAP-5 is done with the validation of GUI generated Input File. The GUI is developed in Microsoft Visual Studio using Visual C Sharp (C) as programming language. The Nodalization diagram is drawn graphically and the program contains various component forms along with the starting data form, which are launched for properties assignment to generate Input File Cards serving as GUI for the user. The GUI is provided with Open / Save function to store and recall the Nodalization diagram along with Components' properties. The GUI generated Input File is validated for several case studies and individual component cards are compared with the originally required format. The generated Input File of RELAP is found consistent with the requirement of RELAP. The GUI provided a useful platform for simulating complex hydrodynamic problems efficiently with RELAP. (author)

Asymmetric focusing study from twin input power couplers using realistic rf cavity field maps

Directory of Open Access Journals (Sweden)

Colwyn Gulliford

2011-03-01

Full Text Available Advanced simulation codes now exist that can self-consistently solve Maxwell’s equations for the combined system of an rf cavity and a beam bunch. While these simulations are important for a complete understanding of the beam dynamics in rf cavities, they require significant time and computing power. These techniques are therefore not readily included in real time simulations useful to the beam physicist during beam operations. Thus, there exists a need for a simplified algorithm which simulates realistic cavity fields significantly faster than self-consistent codes, while still incorporating enough of the necessary physics to ensure accurate beam dynamics computation. To this end, we establish a procedure for producing realistic field maps using lossless cavity eigenmode field solvers. This algorithm incorporates all relevant cavity design and operating parameters, including beam loading from a nonrelativistic beam. The algorithm is then used to investigate the asymmetric quadrupolelike focusing produced by the input couplers of the Cornell ERL injector cavity for a variety of beam and operating parameters.

Form follows function: the architecture of operational requirements. [Winstow Mine of UK

Energy Technology Data Exchange (ETDEWEB)

Crawford, C W

1984-07-01

Wistow Mine, in the Selby Coalfield (UK) has recently received a Festival of Architecture Award. The success of the visual appearance of the site is the result of careful consideration of the NCB's operational requirements, by a special design team, and the subsequent development of designs for all the buildings on the site and the layout of the site itself, which satisfy those requirements.

Requirements on qualification, competence and sufficient number of personnel for NPP operation

International Nuclear Information System (INIS)

Simon, M.

2004-01-01

The safe operation of NPPs presupposes qualified personnel on site in sufficient numbers. While the acquisition and preservation of technical expertise and the qualification of the shift personnel and other staff is well regulated by regulatory guidelines in Germany, there is a lack of such regulations with the exception for shift personnel - for the minimum number of technical personnel required for safe operation of a NPP. By order of the BMU, an attempt was made with this study to work out the requirements for qualification, competence and number of personnel to be maintained at the plant, representing the minimum requirements for safe operation of a NPP. The scope of the project was restricted to requirements for technical plant personnel. The aim was to work out requirements which would be as independent as possible of the existing organisation in a particular power plant. This study therefore does not assume a given organisational structure but was rather more oriented on the work processes in a NPP which are the basis for planning and performing routine work in the plant. For the study a work process model of typical tasks in a NPP had to be developed. Then, the tasks to be performed within the so defined work processes were described (task profiles) on the basis of existing manuals for plant organisation. From these task profiles such tasks were defined or selected which shall not be delegated to external personnel for specific reasons, and which were called vital competences. To keep these vital competences at the plant, an assessment and/or calculation of the necessary number of plant technical personnel was made using the task profiles for responsible personnel, but also by the evaluation of thousands of work orders for maintenance personnel. On the basis of these data, a proposal was made for the minimal number of technical personnel which is necessary to operate a NPP unit safely. Beside of this number, general criteria were developed which should be

Operational analysis supporting the definition of the repository/transportation interface

International Nuclear Information System (INIS)

Peterson, R.W.; Smith, L.A.; Wampler, J.A.

1985-06-01

This report discusses progress made to date in an on-going effort to analyze operations at the repository-transportation interface of the Mined Geologic Disposal System of the Salt Repository Project (SRP). The interface is where the two systems actually are in physical contact with one another. The overall intent of the on-going effort is to to evaluate several interface design concepts for the extent to which workers are exposed to radiation, for the time required to receive and process transportation casks, and for the associated capital and operating costs. The design criteria report will outline interface functional requirements, which when incorporated into the interfacing systems (transportation-repository receiving), will ensure their physical compatibility, their optimal operation, and their compliance with performance standards. The final design criteria report will subsequently serve as an input to the receiving facility design portions of the SRP System Design Description (SDD), and System Requirements Specifications (SRS), and to the transportation cask design specifications. 6 refs., 13 figs., 6 tabs

78 FR 42323 - Pilot Certification and Qualification Requirements for Air Carrier Operations

Science.gov (United States)

2013-07-15

... leadership, professionalism, and mentoring skills, stabilized approaches, and operations in icing conditions... leadership, professionalism, and first officer assertiveness (Recommendation A-10- 15 and A-11-39); Require... fundamentals of instruction. [[Page 42331

Energy Systems Test Area (ESTA) Pyrotechnic Operations: User Test Planning Guide

Science.gov (United States)

Hacker, Scott

2012-01-01

The Johnson Space Center (JSC) has created and refined innovative analysis, design, development, and testing techniques that have been demonstrated in all phases of spaceflight. JSC is uniquely positioned to apply this expertise to components, systems, and vehicles that operate in remote or harsh environments. We offer a highly skilled workforce, unique facilities, flexible project management, and a proven management system. The purpose of this guide is to acquaint Test Requesters with the requirements for test, analysis, or simulation services at JSC. The guide includes facility services and capabilities, inputs required by the facility, major milestones, a roadmap of the facility s process, and roles and responsibilities of the facility and the requester. Samples of deliverables, facility interfaces, and inputs necessary to define the cost and schedule are included as appendices to the guide.

14 CFR 119.65 - Management personnel required for operations conducted under part 121 of this chapter.

Science.gov (United States)

2010-01-01

... or Part 135 of This Chapter § 119.65 Management personnel required for operations conducted under... of management personnel due to— (1) The kind of operation involved; (2) The number and type of... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Management personnel required for...

14 CFR 119.69 - Management personnel required for operations conducted under part 135 of this chapter.

Science.gov (United States)

2010-01-01

... or Part 135 of This Chapter § 119.69 Management personnel required for operations conducted under... of management personnel due to— (1) The kind of operation involved; (2) The number and type of... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Management personnel required for...

Development of Small UAS Beyond-Visual-Line-of-Sight (BVLOS Flight Operations: System Requirements and Procedures

Directory of Open Access Journals (Sweden)

Scott Xiang Fang

2018-04-01

Full Text Available Due to safety concerns of integrating small unmanned aircraft systems (UAS into non-segregated airspace, aviation authorities have required a set of detect and avoid (DAA systems to be equipped on small UAS for beyond-visual-line-of-sight (BVLOS flight operations in civil airspace. However, the development of small UAS DAA systems also requires BVLOS flights for testing and validation. To mitigate operational risks for small UAS BVLOS flight operations, this paper proposes to initially test small UAS DAA systems in BVLOS flights in a restricted airspace with additional safety features. Later, this paper further discusses the operating procedures and emergency action plans for small UAS BVLOS flight operations. The testing results show that these safety systems developed can help improve operational safety for small UAS BVLOS flight operations.

Reactor core modeling practice: Operational requirements, model characteristics, and model validation

International Nuclear Information System (INIS)

Zerbino, H.

1997-01-01

The physical models implemented in power plant simulators have greatly increased in performance and complexity in recent years. This process has been enabled by the ever increasing computing power available at affordable prices. This paper describes this process from several angles: First the operational requirements which are more critical from the point of view of model performance, both for normal and off-normal operating conditions; A second section discusses core model characteristics in the light of the solutions implemented by Thomson Training and Simulation (TT and S) in several full-scope simulators recently built and delivered for Dutch, German, and French nuclear power plants; finally we consider the model validation procedures, which are of course an integral part of model development, and which are becoming more and more severe as performance expectations increase. As a conclusion, it may be asserted that in the core modeling field, as in other areas, the general improvement in the quality of simulation codes has resulted in a fairly rapid convergence towards mainstream engineering-grade calculations. This is remarkable performance in view of the stringent real-time requirements which the simulation codes must satisfy as well as the extremely wide range of operating conditions that they are called upon to cover with good accuracy. (author)

Estimating energy requirement in cashew (Anacardium occidentale L.) nut processing operations

Energy Technology Data Exchange (ETDEWEB)

Jekayinfa, S.O. [Department of Agricultural Engineering, Ladoke Akintola University of Technology, P.M.B. 4000, Ogbomoso, Oyo State (Nigeria); Bamgboye, A.I. [Department of Agricultural Engineering, University of Ibadan, Ibadan (Nigeria)

2006-07-15

This work deals with a study on estimation of energy consumption in eight readily defined unit operations of cashew nut processing. Data for analysis were collected from nine cashew nut mills stratified into small, medium and large categories to represent different mechanization levels. Series of equations were developed to easily compute requirements of electricity, fuel and labour for each of the unit operations. The computation of energy use was done using spreadsheet program on Microsoft Excel. The results of application test of the equations show that the total energy intensity in the cashew nut mills varied between 0.21 and 1.161MJ/kg. Electrical energy intensity varied between 0.0052 and 0.029MJ/kg, while thermal energy intensity varied from 0.085 to 1.064MJ/kg. The two identified energy intensive operations in cashew nut processing are cashew nut drying and cashew nut roasting, altogether accounting for over 85% of the total energy consumption in all the three mill categories. Thermal energy, obtained from diesel fuel, represented about 90% of the unit energy cost for cashew nut processing. The developed equations have therefore proven to be a useful tool for carrying out budgeting, forecasting energy requirements and planning plant expansion. (author)

Reprocessing input data validation

International Nuclear Information System (INIS)

Persiani, P.J.; Bucher, R.G.; Pond, R.B.; Cornella, R.J.

1990-01-01

The Isotope Correlation Technique (ICT), in conjunction with the gravimetric (Pu/U ratio) method for mass determination, provides an independent verification of the input accountancy at the dissolver or accountancy stage of the reprocessing plant. The Isotope Correlation Technique has been applied to many classes of domestic and international reactor systems (light-water, heavy-water, graphite, and liquid-metal) operating in a variety of modes (power, research, production, and breeder), and for a variety of reprocessing fuel cycle management strategies. Analysis of reprocessing operations data based on isotopic correlations derived for assemblies in a PWR environment and fuel management scheme, yielded differences between the measurement-derived and ICT-derived plutonium mass determinations of (-0.02 ± 0.23)% for the measured U-235 and (+0.50 ± 0.31)% for the measured Pu-239, for a core campaign. The ICT analyses has been implemented for the plutonium isotopics in a depleted uranium assembly in a heavy-water, enriched uranium system and for the uranium isotopes in the fuel assemblies in light-water, highly-enriched systems. 7 refs., 5 figs., 4 tabs

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Chinese Ed.)

International Nuclear Information System (INIS)

2012-01-01

On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (French Ed.)

International Nuclear Information System (INIS)

2012-01-01

On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Arabic Ed.)

International Nuclear Information System (INIS)

2012-01-01

On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Lessons learned using HAMMLAB experimenter systems: Input for HAMMLAB 2000 functional requirements

International Nuclear Information System (INIS)

Sebok, Angelia L.

1998-02-01

To design a usable HAMMLAB 2000, lessons learned from use of the existing HAMMLAB must be documented. User suggestions are important and must be taken into account. Different roles in HAMMLAB experimental sessions are identified, and major functions of each role were specified. A series of questionnaires were developed and administered to different users of HAMMLAB, each tailored to the individual job description. The results of those questionnaires are included in this report. Previous HAMMLAB modification recommendations were also reviewed, to provide input to this document. A trial experimental session was also conducted, to give an overview of the tasks in HAMMLAB. (author)

Reactivity variation's analysis in nuclear propulsion considering the operational real conditions requirements

International Nuclear Information System (INIS)

Pires, Leonardo Paredes; Santos, Rubens Souza dos; Lapa, Marcelo Franklin

2015-01-01

The work presented in this paper highlights the need for the study to determine the reactivity variation ramps needed and possible to meet the real operational conditions required by a nuclear submarine in this several operating phases. In accordance with the operational needs and necessary maneuvers in certain tactical situations, large power variations in the propulsion are demanded. As these sudden and severe changes in propulsion come from the thermal power of nuclear origin, the operation of the nuclear island has to know what kind of answers and criticality variations are necessary to meet each demand speed required. It should be noted that these criticality inserts are conditioned, not only by the propulsion needs, but fundamentally by the imperative need to ensure the core integrity and the chain reaction sustainability considering the phenomenons and complex effects, nonlinear and retro-fed involved. It has to be determined what is the past and required time for each criticality insertion is perceived as motor power. Considering the highlighted aspects, this article concludes and indicates to its end, the need to establish a base operating transitional agenda, according to the naval combat doctrine, to be tested and analyzed under the aspects and peculiarities of kinetic reactors, with the purpose of being generated the appropriate criticality curves for each real need and their respective times of anticipated action. (author)

Reactivity variation's analysis in nuclear propulsion considering the operational real conditions requirements

Energy Technology Data Exchange (ETDEWEB)

Pires, Leonardo Paredes; Santos, Rubens Souza dos; Lapa, Marcelo Franklin, E-mail: leonardo_paredes@icloud.com, E-mail: lapa@ien.gov.br, E-mail: rsantos@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

2015-07-01

The work presented in this paper highlights the need for the study to determine the reactivity variation ramps needed and possible to meet the real operational conditions required by a nuclear submarine in this several operating phases. In accordance with the operational needs and necessary maneuvers in certain tactical situations, large power variations in the propulsion are demanded. As these sudden and severe changes in propulsion come from the thermal power of nuclear origin, the operation of the nuclear island has to know what kind of answers and criticality variations are necessary to meet each demand speed required. It should be noted that these criticality inserts are conditioned, not only by the propulsion needs, but fundamentally by the imperative need to ensure the core integrity and the chain reaction sustainability considering the phenomenons and complex effects, nonlinear and retro-fed involved. It has to be determined what is the past and required time for each criticality insertion is perceived as motor power. Considering the highlighted aspects, this article concludes and indicates to its end, the need to establish a base operating transitional agenda, according to the naval combat doctrine, to be tested and analyzed under the aspects and peculiarities of kinetic reactors, with the purpose of being generated the appropriate criticality curves for each real need and their respective times of anticipated action. (author)

Estimation of crop water requirements using remote sensing for operational water resources management

Science.gov (United States)

Vasiliades, Lampros; Spiliotopoulos, Marios; Tzabiras, John; Loukas, Athanasios; Mylopoulos, Nikitas

2015-06-01

An integrated modeling system, developed in the framework of "Hydromentor" research project, is applied to evaluate crop water requirements for operational water resources management at Lake Karla watershed, Greece. The framework includes coupled components for operation of hydrotechnical projects (reservoir operation and irrigation works) and estimation of agricultural water demands at several spatial scales using remote sensing. The study area was sub-divided into irrigation zones based on land use maps derived from Landsat 5 TM images for the year 2007. Satellite-based energy balance for mapping evapotranspiration with internalized calibration (METRIC) was used to derive actual evapotranspiration (ET) and crop coefficient (ETrF) values from Landsat TM imagery. Agricultural water needs were estimated using the FAO method for each zone and each control node of the system for a number of water resources management strategies. Two operational strategies of hydro-technical project development (present situation without operation of the reservoir and future situation with the operation of the reservoir) are coupled with three water demand strategies. In total, eight (8) water management strategies are evaluated and compared. The results show that, under the existing operational water resources management strategies, the crop water requirements are quite large. However, the operation of the proposed hydro-technical projects in Lake Karla watershed coupled with water demand management measures, like improvement of existing water distribution systems, change of irrigation methods, and changes of crop cultivation could alleviate the problem and lead to sustainable and ecological use of water resources in the study area.

On Input Vector Representation for the SVR model of Reactor Core Loading Pattern Critical Parameters

International Nuclear Information System (INIS)

Trontl, K.; Pevec, D.; Smuc, T.

2008-01-01

Determination and optimization of reactor core loading pattern is an important factor in nuclear power plant operation. The goal is to minimize the amount of enriched uranium (fresh fuel) and burnable absorbers placed in the core, while maintaining nuclear power plant operational and safety characteristics. The usual approach to loading pattern optimization involves high degree of engineering judgment, a set of heuristic rules, an optimization algorithm and a computer code used for evaluating proposed loading patterns. The speed of the optimization process is highly dependent on the computer code used for the evaluation. Recently, we proposed a new method for fast loading pattern evaluation based on general robust regression model relying on the state of the art research in the field of machine learning. We employed Support Vector Regression (SVR) technique. SVR is a supervised learning method in which model parameters are automatically determined by solving a quadratic optimization problem. The preliminary tests revealed a good potential of the SVR method application for fast and accurate reactor core loading pattern evaluation. However, some aspects of model development are still unresolved. The main objective of the work reported in this paper was to conduct additional tests and analyses required for full clarification of the SVR applicability for loading pattern evaluation. We focused our attention on the parameters defining input vector, primarily its structure and complexity, and parameters defining kernel functions. All the tests were conducted on the NPP Krsko reactor core, using MCRAC code for the calculation of reactor core loading pattern critical parameters. The tested input vector structures did not influence the accuracy of the models suggesting that the initially tested input vector, consisted of the number of IFBAs and the k-inf at the beginning of the cycle, is adequate. The influence of kernel function specific parameters (σ for RBF kernel

The JPL functional requirements tool

Science.gov (United States)

Giffin, Geoff; Skinner, Judith; Stoller, Richard

1987-01-01

Planetary spacecraft are complex vehicles which are built according to many thousands of requirements. Problems encountered in documenting and maintaining these requirements led to the current attempt to reduce or eliminate these problems by a computer automated data base Functional Requirements Tool. The tool developed at JPL and in use on several JPL Projects is described. The organization and functionality of the Tool, together with an explanation of the data base inputs, their relationships, and use are presented. Methods of interfacing with external documents, representation of tables and figures, and methods of approval and change processing are discussed. The options available for disseminating information from the Tool are identified. The implementation of the Requirements Tool is outlined, and the operation is summarized. The conclusions drawn from this work is that the Requirements Tool represents a useful addition to the System Engineer's Tool kit, it is not currently available elsewhere, and a clear development path exists to expand the capabilities of the Tool to serve larger and more complex projects.

Development of EPICS Input Output Controller and User Interface for the PEFP Low Level RF Control System

International Nuclear Information System (INIS)

Song, Young Gi; Kim, Han Sung; Seol, Kyung Tae; Kwon, Hyeok Jung; Cho, Yong Sub

2010-01-01

The Low-Level RF (LLRF) control system of the Proton Engineering Frontier Project (PEFP) was developed for handling the driving frequency for Quadrupole (RFQ) and the Draft Tube Linac (DTL) cavities in 2006. The RF amplitude and phase of the accelerating field were controlled within 1% and 1 degree by stability requirements, respectively. Operators have been using the LLRF control system under the windows based text console mode as an operator interface. The LLRF control system could not be integrated with Experimental Physics Industrial Control System (EPICS) Input Output Controllers (IOC) for each subsection of PEFP facility. The main objective of this study is to supply operators of the LLRF control system with user friendly and convenient operating environment. The new LLRF control system is composed of a Verse Module Eurocard (VME) baseboard, a PCI Mezzanine Card (PMC), Board Support Package (BSP), EPICS software tool and a Real-Time Operating System (RTOS) VxWorks. A test with a dummy cavity of the new LLRF control system shows that operators can control and monitor operation parameters for a desired feedback action by using EPICS Channel Access (CA).

Development of EPICS Input Output Controller and User Interface for the PEFP Low Level RF Control System

Energy Technology Data Exchange (ETDEWEB)

Song, Young Gi; Kim, Han Sung; Seol, Kyung Tae; Kwon, Hyeok Jung; Cho, Yong Sub [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2010-05-15

The Low-Level RF (LLRF) control system of the Proton Engineering Frontier Project (PEFP) was developed for handling the driving frequency for Quadrupole (RFQ) and the Draft Tube Linac (DTL) cavities in 2006. The RF amplitude and phase of the accelerating field were controlled within 1% and 1 degree by stability requirements, respectively. Operators have been using the LLRF control system under the windows based text console mode as an operator interface. The LLRF control system could not be integrated with Experimental Physics Industrial Control System (EPICS) Input Output Controllers (IOC) for each subsection of PEFP facility. The main objective of this study is to supply operators of the LLRF control system with user friendly and convenient operating environment. The new LLRF control system is composed of a Verse Module Eurocard (VME) baseboard, a PCI Mezzanine Card (PMC), Board Support Package (BSP), EPICS software tool and a Real-Time Operating System (RTOS) VxWorks. A test with a dummy cavity of the new LLRF control system shows that operators can control and monitor operation parameters for a desired feedback action by using EPICS Channel Access (CA).

Alternative input medium development for wheelchair user with severe spinal cord injury

Science.gov (United States)

Ihsan, Izzat Aqmar; Tomari, Razali; Zakaria, Wan Nurshazwani Wan; Othman, Nurmiza

2017-09-01

Quadriplegia or tetraplegia patients have restricted four limbs as well as torso movement caused by severe spinal cord injury. Undoubtedly, these patients face difficulties when operating their powered electric wheelchair since they are unable to control the wheelchair by means of a standard joystick. Due to total loss of both sensory and motor function of the four limbs and torso, an alternative input medium for the wheelchair will be developed to assist the user in operating the wheelchair. In this framework, the direction of the wheelchair movement is determined by the user's conscious intent through a brain control interface (BCI) based on Electroencephalogram (EEG) signal. A laser range finder (LFR) is used to perceive environment information for determining a safety distance of the wheelchair's surrounding. Local path planning algorithm will be developed to provide navigation planner along with user's input to prevent collision during control operation.

A remote control system to offer information for nuclear power plant operation

International Nuclear Information System (INIS)

Ohga, Yukiharu; Yuchi, Hiroyuki; Arita, Setsuo

1995-01-01

A new man-machine system was proposed to simplify input operation so as to get needed plant information and to control information items and output devices for the operator crew, working in a control room. The system controls the shared information for the operator crew, on a large screen display, and private information for individual operators and maintenance personnel, on CRTs, based on the speech input and remote pointing input to the large screen display by a portable pointer, which emits laser beams. The system recognizes the indicating point of the pointer beam by processing the image on the large screen as obtained by an ITV camera. An infrared laser beam and a camera with a visible ray cut filter are used to remove distortion of the image caused by lens aberration, etc. and to provide rapid image processing. The operator performs the input operation while monitoring a cursor displayed by the system. The information items offered and their output devices are automatically determined according to the input operator. A prototype system was developed using three CRTs, one of which served as a substitute for the large screen display. Input to the system is performed using a speech input device and three kinds of pointers; each pointer is identified during image processing based on the number of laser beams emitted. The evaluation test confirmed that precise and smooth input by pointers as well as arbitrary combinations with speech input realized natural dialog without being aware of any waiting time. The appropriate information items were offered to output devices, CRTs and the speech output device, according to the pointers used, namely the input operators. The system can simplify input operation and effectively control the offered information items and output devices in a plant control room. (author)

Network and neuronal membrane properties in hybrid networks reciprocally regulate selectivity to rapid thalamocortical inputs.

Science.gov (United States)

Pesavento, Michael J; Pinto, David J

2012-11-01

Rapidly changing environments require rapid processing from sensory inputs. Varying deflection velocities of a rodent's primary facial vibrissa cause varying temporal neuronal activity profiles within the ventral posteromedial thalamic nucleus. Local neuron populations in a single somatosensory layer 4 barrel transform sparsely coded input into a spike count based on the input's temporal profile. We investigate this transformation by creating a barrel-like hybrid network with whole cell recordings of in vitro neurons from a cortical slice preparation, embedding the biological neuron in the simulated network by presenting virtual synaptic conductances via a conductance clamp. Utilizing the hybrid network, we examine the reciprocal network properties (local excitatory and inhibitory synaptic convergence) and neuronal membrane properties (input resistance) by altering the barrel population response to diverse thalamic input. In the presence of local network input, neurons are more selective to thalamic input timing; this arises from strong feedforward inhibition. Strongly inhibitory (damping) network regimes are more selective to timing and less selective to the magnitude of input but require stronger initial input. Input selectivity relies heavily on the different membrane properties of excitatory and inhibitory neurons. When inhibitory and excitatory neurons had identical membrane properties, the sensitivity of in vitro neurons to temporal vs. magnitude features of input was substantially reduced. Increasing the mean leak conductance of the inhibitory cells decreased the network's temporal sensitivity, whereas increasing excitatory leak conductance enhanced magnitude sensitivity. Local network synapses are essential in shaping thalamic input, and differing membrane properties of functional classes reciprocally modulate this effect.

IDENTIFYING OPERATIONAL REQUIREMENTS TO SELECT SUITABLE DECISION MODELS FOR A PUBLIC SECTOR EPROCUREMENT DECISION SUPPORT SYSTEM

Directory of Open Access Journals (Sweden)

Mohamed Adil

2014-10-01

Full Text Available Public sector procurement should be a transparent and fair process. Strict legal requirements are enforced on public sector procurement to make it a standardised process. To make fair decisions on selecting suppliers, a practical method which adheres to legal requirements is important. The research that is the base for this paper aimed at identifying a suitable Multi-Criteria Decision Analysis (MCDA method for the specific legal and functional needs of the Maldivian Public Sector. To identify such operational requirements, a set of focus group interviews were conducted in the Maldives with public officials responsible for procurement decision making. Based on the operational requirements identified through focus groups, criteria-based evaluation is done on published MCDA methods to identify the suitable methods for e-procurement decision making. This paper describes the identification of the operational requirements and the results of the evaluation to select suitable decision models for the Maldivian context.

17 CFR 249.821 - Form PILOT, information required of self-regulatory organizations operating pilot trading systems...

Science.gov (United States)

2010-04-01

... required of self-regulatory organizations operating pilot trading systems pursuant to § 240.19b-5 of this... Associations § 249.821 Form PILOT, information required of self-regulatory organizations operating pilot trading systems pursuant to § 240.19b-5 of this chapter. This form shall be used by all self-regulatory...

40 CFR 63.9900 - What are my operation and maintenance requirements?

Science.gov (United States)

2010-07-01

.... You must keep the plan for the life of the affected source or until the affected source is no longer... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES... required by § 63.6(e)(1)(i), you must always operate and maintain your affected source, including air...

Advanced information processing system: Input/output network management software

Science.gov (United States)

Nagle, Gail; Alger, Linda; Kemp, Alexander

1988-01-01

The purpose of this document is to provide the software requirements and specifications for the Input/Output Network Management Services for the Advanced Information Processing System. This introduction and overview section is provided to briefly outline the overall architecture and software requirements of the AIPS system before discussing the details of the design requirements and specifications of the AIPS I/O Network Management software. A brief overview of the AIPS architecture followed by a more detailed description of the network architecture.

An input feature selection method applied to fuzzy neural networks for signal esitmation

International Nuclear Information System (INIS)

Na, Man Gyun; Sim, Young Rok

2001-01-01

It is well known that the performance of a fuzzy neural networks strongly depends on the input features selected for its training. In its applications to sensor signal estimation, there are a large number of input variables related with an output. As the number of input variables increases, the training time of fuzzy neural networks required increases exponentially. Thus, it is essential to reduce the number of inputs to a fuzzy neural networks and to select the optimum number of mutually independent inputs that are able to clearly define the input-output mapping. In this work, principal component analysis (PAC), genetic algorithms (GA) and probability theory are combined to select new important input features. A proposed feature selection method is applied to the signal estimation of the steam generator water level, the hot-leg flowrate, the pressurizer water level and the pressurizer pressure sensors in pressurized water reactors and compared with other input feature selection methods

Design Requirements for Unmanned Rotorcraft Used in Low-Risk Concepts of Operation

Science.gov (United States)

Hayhurst, Kelly J.; Maddalon, Jeffrey M.; Neogi, Natasha A.; Verstynen, Harry A.

2016-01-01

This technical report presents the results of the second of two research studies on design and performance requirements supporting airworthiness certification of midrange unmanned aircraft systems (UAS) intended for commercial use. The two studies focused attention on UAS in the middle of the multidimensional spectrum of UAS; that is, UAS with attributes and capabilities exceeding the criteria to operate under Part 107 of the Federal Aviation Regulations (FARs), but without the design or operational capabilities to comply with the airworthiness standards for commercially-operated manned aircraft. The goal of the two studies was to help address the gap in airworthiness standards for some UAS that fall between the extremes.

INEL Operable Unit 7-13 containment and stabilization configuration option

International Nuclear Information System (INIS)

Raivo, B.D.; Richardson, J.G.; Nickelson, D.F.

1993-05-01

A containment and stabilization configuration option has been developed for the Idaho National Engineering Laboratory's Subsurface Disposal Area Operable Unit 7-13, the transuranic (TRU)-contaminated waste pits and trenches. The configuration option is presented as an end-to-end system block diagram. Functional subelements are separately discussed, and technical background information, assumptions, input, high-level subelement requirements, and output are presented for each option

Information Operations - Analysis Support and Capability Requirements (Operations d'information - Soutien a l'analyse et exigences de capacites) (CD-ROM)

National Research Council Canada - National Science Library

2006-01-01

...: The focus of the study "Information Operations - Analysis Support and Capability Requirements" undertaken by the RTO Task Group SAS-057 was to provide recommendations to improve analysis support...

Technical Requirements Analysis and Control Systems (TRACS) Initial Operating Capability (IOC) documentation

Science.gov (United States)

Hammond, Dana P.

1991-01-01

The Technical Requirements Analysis and Control Systems (TRACS) software package is described. TRACS offers supplemental tools for the analysis, control, and interchange of project requirements. This package provides the fundamental capability to analyze and control requirements, serves a focal point for project requirements, and integrates a system that supports efficient and consistent operations. TRACS uses relational data base technology (ORACLE) in a stand alone or in a distributed environment that can be used to coordinate the activities required to support a project through its entire life cycle. TRACS uses a set of keyword and mouse driven screens (HyperCard) which imposes adherence through a controlled user interface. The user interface provides an interactive capability to interrogate the data base and to display or print project requirement information. TRACS has a limited report capability, but can be extended with PostScript conventions.

Romania - NPP PLiM Between Regulatory Requirement / Oversight and Operator Safety / Financial Interest

International Nuclear Information System (INIS)

Goicea, Lucian

2012-01-01

Cernavoda Unit 1 PLiM started in the first third of its design life, to develop as regulatory requirements of the components of standards and programmes and to benefit by earlier implementation of the measures for achieving maximum operating life. CNCAN regulatory present approach on the utility PLiM combines the regulatory requirements on management system, ageing management provisions of periodic safety review, detailed technical requirements of ageing programmes and different techniques focusing only on safety issues. (author)

Requirements Analysis Study for Master Pump Shutdown System Project Development Specification

International Nuclear Information System (INIS)

BEVINS, R.R.

2000-01-01

This study is a requirements document that presents analysis for the functional description for the master pump shutdown system. This document identifies the sources of the requirements and/or how these were derived. Each requirement is validated either by quoting the source or an analysis process involving the required functionality, performance characteristics, operations input or engineering judgment. The requirements in this study apply to the first phase of the W314 Project. This document has been updated during the definitive design portion of the first phase of the W314 Project to capture additional software requirements and is planned to be updated during the second phase of the W314 Project to cover the second phase of the project's scope

JET-ISX-B beryllium limiter experiment safety analysis report and operational safety requirements

International Nuclear Information System (INIS)

Edmonds, P.H.

1985-09-01

An experiment to evaluate the suitability of beryllium as a limiter material has been completed on the ISX-B tokamak. The experiment consisted of two phases: (1) the initial operation and characterization in the ISX experiment, and a period of continued operation to the specified surface fluence (10 22 atoms/cm 2 ) of hydrogen ions; and (2) the disassembly, decontamination, or disposal of the ISX facility. During these two phases of the project, the possibility existed for beryllium and/or beryllium oxide powder to be produced inside the vacuum vessel. Beryllium dust is a highly toxic material, and extensive precautions are required to prevent the release of the beryllium into the experimental work area and to prevent the contamination of personnel working on the device. Details of the health hazards associated with beryllium and the appropriate precautions are presented. Also described in appendixes to this report are the various operational safety requirements for the project

Enhancing MINIX 3.X input/output performance

OpenAIRE

Pessolani, Pablo Andrés; Weisz, Gustavo; Bardus, Marisa; Hein, César

2008-01-01

MINIX 3.X is an open-source operating system designed to be highly reliable, flexible, and secure. The kernel is extremely small and user processes, specialized servers and device driver runs as user-mode insulated processes. These features, the tiny amount of kernel code, and other aspects greatly enhance system reliability. The drawbacks of running device drivers in user-mode are the performance penalties on input/output ports access, kernel data structures access, interrupt indirect man...

The role of additive neurogenesis and synaptic plasticity in a hippocampal memory model with grid-cell like input.

Directory of Open Access Journals (Sweden)

Peter A Appleby

Full Text Available Recently, we presented a study of adult neurogenesis in a simplified hippocampal memory model. The network was required to encode and decode memory patterns despite changing input statistics. We showed that additive neurogenesis was a more effective adaptation strategy compared to neuronal turnover and conventional synaptic plasticity as it allowed the network to respond to changes in the input statistics while preserving representations of earlier environments. Here we extend our model to include realistic, spatially driven input firing patterns in the form of grid cells in the entorhinal cortex. We compare network performance across a sequence of spatial environments using three distinct adaptation strategies: conventional synaptic plasticity, where the network is of fixed size but the connectivity is plastic; neuronal turnover, where the network is of fixed size but units in the network may die and be replaced; and additive neurogenesis, where the network starts out with fewer initial units but grows over time. We confirm that additive neurogenesis is a superior adaptation strategy when using realistic, spatially structured input patterns. We then show that a more biologically plausible neurogenesis rule that incorporates cell death and enhanced plasticity of new granule cells has an overall performance significantly better than any one of the three individual strategies operating alone. This adaptation rule can be tailored to maximise performance of the network when operating as either a short- or long-term memory store. We also examine the time course of adult neurogenesis over the lifetime of an animal raised under different hypothetical rearing conditions. These growth profiles have several distinct features that form a theoretical prediction that could be tested experimentally. Finally, we show that place cells can emerge and refine in a realistic manner in our model as a direct result of the sparsification performed by the dentate gyrus

40 CFR 63.7826 - How do I demonstrate initial compliance with the operation and maintenance requirements that...

Science.gov (United States)

2010-07-01

... preventative maintenance schedule and, as applicable, detailed descriptions of the corrective action procedures... compliance with the operation and maintenance requirements that apply to me? 63.7826 Section 63.7826... Compliance Requirements § 63.7826 How do I demonstrate initial compliance with the operation and maintenance...

46 CFR 189.50-1 - Inspection and testing required when making alterations, repairs, or other such operations...

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection and testing required when making alterations, repairs, or other such operations involving riveting, welding, burning, or like fire-producing actions... and testing required when making alterations, repairs, or other such operations involving riveting...

46 CFR 91.50-1 - Inspection and testing required when making alterations, repairs, or other such operations...

Science.gov (United States)

2010-10-01

... testing required when making alterations, repairs, or other such operations involving riveting, welding... 46 Shipping 4 2010-10-01 2010-10-01 false Inspection and testing required when making alterations, repairs, or other such operations involving riveting, welding, burning or like fire-producing actions. 91...

Design and Implementation of Kana-Input Navigation System for Kids based on the Cyber Assistant

Directory of Open Access Journals (Sweden)

Hiroshi Matsuda

2004-02-01

Full Text Available In Japan, it has increased the opportunity for young children to experience the personal computer in elementary schools. However, in order to use computer, many domestic barriers have confronted young children (Kids because they cannot read difficult Kanji characters and had not learnt Roman alphabet yet. As a result, they cannot input text strings by JIS Kana keyboard. In this research, we developed Kana-Input NaVigation System for kids (KINVS based on the Cyber Assistant System (CAS. CAS is a Human-Style Software Robot based on the 3D-CG real-time animation and voice synthesis technology. KINVS enables to input Hiragana/Katakana characters by mouse operation only (without keyboard operation and CAS supports them by using speaking, facial expression, body action and sound effects. KINVS displays the 3D-Stage like a classroom. In this room, Blackboard, Interactive parts to input Kana-characters, and CAS are placed. As some results of preliminary experiments, it is definitely unfit for Kids to double-click objects quickly or to move the Scrollbar by mouse dragging. So, mouse input method of KINVS are designed to use only single click and wheeler rotation. To input characters, Kids clicks or rotates the Interactive Parts. KINVS reports all information by voice speaking and Kana subtitles instead of Kanji text. Furthermore, to verify the functional feature of KINVS, we measured how long Kids had taken to input long text by using KINVS.

IM-135-562-00 IDIM instruction manual for the isolated digital input module for SLC

International Nuclear Information System (INIS)

Kieffer, J.

1983-01-01

This unit is designed as a general purpose digital input module. Each input is opto-isolated, and is designed to operate over a wide range of positive input voltages. The unit is nonlatching, each CAMAC Read of the unit presenting the data as seen at the inputs at the time of the Read command. The manual includes the following sections: specifications; front panel, lights and connectors; reference list; functional description; 82S100 logic equations; test and checkout procedures; appendix A, SLAC 82S100 programming data; and appendix B, JXK-FORTH 135-562 program listing

TASS/SMR Code Topical Report for SMART Plant, Vol II: User's Guide and Input Requirement

Energy Technology Data Exchange (ETDEWEB)

Kim, See Darl; Kim, Soo Hyoung; Kim, Hyung Rae (and others)

2008-10-15

The TASS/SMR code has been developed with domestic technologies for the safety analysis of the SMART plant which is an integral type pressurized water reactor. It can be applied to the analysis of design basis accidents including non-LOCA (loss of coolant accident) and LOCA of the SMART plant. The TASS/SMR code can be applied to any plant regardless of the structural characteristics of a reactor since the code solves the same governing equations for both the primary and secondary system. The code has been developed to meet the requirements of the safety analysis code. This report describes the overall structure of the TASS/SMR, input processing, and the processes of a steady state and transient calculations. In addition, basic differential equations, finite difference equations, state relationships, and constitutive models are described in the report. First, the conservation equations, a discretization process for numerical analysis, search method for state relationship are described. Then, a core power model, heat transfer models, physical models for various components, and control and trip models are explained.

Promoting awareness of legal requirements and liabilities in food and beverage operations

Directory of Open Access Journals (Sweden)

A. Nicolaides

2012-01-01

Full Text Available The purpose of this article is to shed more light on the importance of promoting greater awareness of legal requirements and liabilities of food and beverage operations (F&B operations. It is a descriptive analysis which highlights aspects related to food hygiene. Managing legal issues in the hospitality industry, especially in F&B, is a tricky business. The magnitude of the global tourism industry means that the laws governing it are exhaustive and at the best of times, highly complex. Since tourists need to eat and drink it is imperative that industry employees have a meaningful grasp on what is expected legally speaking. Tourists spend large amounts of money on food and beverages and this is second only to airfare to and from destinations. Creating awareness of legal requirements and liabilities in food and beverage operations among industry employees is essential. As very little has been written on consumer rights and industry obligations in the South African hospitality industry food and beverage context, it is hope that this article will create greater awareness of a critically important aspect in the hospitality industry.

Input/Output of ab-initio nuclear structure calculations for improved performance and portability

International Nuclear Information System (INIS)

Laghave, Nikhil

2010-01-01

Many modern scientific applications rely on highly computation intensive calculations. However, most applications do not concentrate as much on the role that input/output operations can play for improved performance and portability. Parallelizing input/output operations of large files can significantly improve the performance of parallel applications where sequential I/O is a bottleneck. A proper choice of I/O library also offers a scope for making input/output operations portable across different architectures. Thus, use of parallel I/O libraries for organizing I/O of large data files offers great scope in improving performance and portability of applications. In particular, sequential I/O has been identified as a bottleneck for the highly scalable MFDn (Many Fermion Dynamics for nuclear structure) code performing ab-initio nuclear structure calculations. We develop interfaces and parallel I/O procedures to use a well-known parallel I/O library in MFDn. As a result, we gain efficient I/O of large datasets along with their portability and ease of use in the down-stream processing. Even situations where the amount of data to be written is not huge, proper use of input/output operations can boost the performance of scientific applications. Application checkpointing offers enormous performance improvement and flexibility by doing a negligible amount of I/O to disk. Checkpointing saves and resumes application state in such a manner that in most cases the application is unaware that there has been an interruption to its execution. This helps in saving large amount of work that has been previously done and continue application execution. This small amount of I/O provides substantial time saving by offering restart/resume capability to applications. The need for checkpointing in optimization code NEWUOA has been identified and checkpoint/restart capability has been implemented in NEWUOA by using simple file I/O.

Manpower and training requirements for operation and maintenance of Nuclear Power Plants

International Nuclear Information System (INIS)

Shah, J.C.

1975-01-01

The experience in India with regard to the staffing of nuclear power station operations and maintenance is encouraging in the sense that given the effort and time, developing countries should not find it unduly difficult to meet their requirements. (orig.) [de

47 CFR 25.263 - Information sharing requirements for SDARS terrestrial repeater operators.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Information sharing requirements for SDARS terrestrial repeater operators. 25.263 Section 25.263 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25.263 Information sharing...

Operating systems

CERN Document Server

Tsichritzis, Dionysios C; Rheinboldt, Werner

1974-01-01

Operating Systems deals with the fundamental concepts and principles that govern the behavior of operating systems. Many issues regarding the structure of operating systems, including the problems of managing processes, processors, and memory, are examined. Various aspects of operating systems are also discussed, from input-output and files to security, protection, reliability, design methods, performance evaluation, and implementation methods.Comprised of 10 chapters, this volume begins with an overview of what constitutes an operating system, followed by a discussion on the definition and pr

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

Documentation of compliance with the energy performance regulations at the end of the detailed design phase is mandatory for building owners in Denmark. Therefore, besides multidisciplinary input, the building design process requires various iterative analyses, so that the optimal solutions can b...

Low-cost USB interface for operant research using Arduino and Visual Basic.

Science.gov (United States)

Escobar, Rogelio; Pérez-Herrera, Carlos A

2015-03-01

This note describes the design of a low-cost interface using Arduino microcontroller boards and Visual Basic programming for operant conditioning research. The board executes one program in Arduino programming language that polls the state of the inputs and generates outputs in an operant chamber. This program communicates through a USB port with another program written in Visual Basic 2010 Express Edition running on a laptop, desktop, netbook computer, or even a tablet equipped with Windows operating system. The Visual Basic program controls schedules of reinforcement and records real-time data. A single Arduino board can be used to control a total of 52 inputs/output lines, and multiple Arduino boards can be used to control multiple operant chambers. An external power supply and a series of micro relays are required to control 28-V DC devices commonly used in operant chambers. Instructions for downloading and using the programs to generate simple and concurrent schedules of reinforcement are provided. Testing suggests that the interface is reliable, accurate, and could serve as an inexpensive alternative to commercial equipment. © Society for the Experimental Analysis of Behavior.

40 CFR 63.7335 - How do I demonstrate continuous compliance with the operation and maintenance requirements that...

Science.gov (United States)

2010-07-01

... corrective action is completed. (c) To demonstrate continuous compliance with the operation and maintenance... compliance with the operation and maintenance requirements that apply to me? 63.7335 Section 63.7335... maintenance requirements that apply to me? (a) For each by-product coke oven battery, you must demonstrate...

Optimal input shaping for Fisher identifiability of control-oriented lithium-ion battery models

Science.gov (United States)

Rothenberger, Michael J.

This dissertation examines the fundamental challenge of optimally shaping input trajectories to maximize parameter identifiability of control-oriented lithium-ion battery models. Identifiability is a property from information theory that determines the solvability of parameter estimation for mathematical models using input-output measurements. This dissertation creates a framework that exploits the Fisher information metric to quantify the level of battery parameter identifiability, optimizes this metric through input shaping, and facilitates faster and more accurate estimation. The popularity of lithium-ion batteries is growing significantly in the energy storage domain, especially for stationary and transportation applications. While these cells have excellent power and energy densities, they are plagued with safety and lifespan concerns. These concerns are often resolved in the industry through conservative current and voltage operating limits, which reduce the overall performance and still lack robustness in detecting catastrophic failure modes. New advances in automotive battery management systems mitigate these challenges through the incorporation of model-based control to increase performance, safety, and lifespan. To achieve these goals, model-based control requires accurate parameterization of the battery model. While many groups in the literature study a variety of methods to perform battery parameter estimation, a fundamental issue of poor parameter identifiability remains apparent for lithium-ion battery models. This fundamental challenge of battery identifiability is studied extensively in the literature, and some groups are even approaching the problem of improving the ability to estimate the model parameters. The first approach is to add additional sensors to the battery to gain more information that is used for estimation. The other main approach is to shape the input trajectories to increase the amount of information that can be gained from input

Storage and distribution/Linear programming for storage operations

Energy Technology Data Exchange (ETDEWEB)

Coleman, D

1978-07-15

The techniques of linear programing to solve storage problems as applied in a tank farm tie-in with refinery throughput operation include: (1) the time-phased model which works on storage and refinery operations input parameters, e.g., production, distribution, cracking, etc., and is capable of representing product stockpiling in slack periods to meet future peak demands, and investigating alternative strategies such as exchange deals and purchase and leasing of additional storage, and (2) the Monte Carlo simulation method, which inputs parameters, e.g., arrival of crude products at refinery, tankage size, likely demand for products, etc., as probability distributions rather than single values, and is capable of showing the average utilization of facilities, potential bottlenecks, investment required to achieve an increase in utilization, and to enable the user to predict total investment, cash flow, and profit emanating from the original financing decision. The increasing use of computer techniques to solve refinery and storage problems is attributed to potential savings resulting from more effective planning, reduced computer costs, ease of access and more usable software. Diagrams.

10 CFR 50.72 - Immediate notification requirements for operating nuclear power reactors.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Immediate notification requirements for operating nuclear power reactors. 50.72 Section 50.72 Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF... systems. (8) Emergency ac electrical power systems, including: Emergency diesel generators (EDGs...

Quantified carbon input for maintaining existing soil organic carbon stocks in global wheat systems

Science.gov (United States)

Wang, G.

2017-12-01

Soil organic carbon (SOC) dynamics in croplands is a crucial component of global carbon (C) cycle. Depending on local environmental conditions and management practices, typical C input is generally required to reduce or reverse C loss in agricultural soils. No studies have quantified the critical C input for maintaining SOC at global scale with high resolution. Such information will provide a baseline map for assessing soil C dynamics under potential changes in management practices and climate, and thus enable development of management strategies to reduce C footprint from farm to regional scales. We used the soil C model RothC to simulate the critical C input rates needed to maintain existing soil C level at 0.1°× 0.1° resolution in global wheat systems. On average, the critical C input was estimated to be 2.0 Mg C ha-1 yr-1, with large spatial variability depending on local soil and climatic conditions. Higher C inputs are required in wheat system of central United States and western Europe, mainly due to the higher current soil C stocks present in these regions. The critical C input could be effectively estimated using a summary model driven by current SOC level, mean annual temperature, precipitation, and soil clay content.

Critical carbon input to maintain current soil organic carbon stocks in global wheat systems.

Science.gov (United States)

Wang, Guocheng; Luo, Zhongkui; Han, Pengfei; Chen, Huansheng; Xu, Jingjing

2016-01-13

Soil organic carbon (SOC) dynamics in croplands is a crucial component of global carbon (C) cycle. Depending on local environmental conditions and management practices, typical C input is generally required to reduce or reverse C loss in agricultural soils. No studies have quantified the critical C input for maintaining SOC at global scale with high resolution. Such information will provide a baseline map for assessing soil C dynamics under potential changes in management practices and climate, and thus enable development of management strategies to reduce C footprint from farm to regional scales. We used the soil C model RothC to simulate the critical C input rates needed to maintain existing soil C level at 0.1° × 0.1° resolution in global wheat systems. On average, the critical C input was estimated to be 2.0 Mg C ha(-1) yr(-1), with large spatial variability depending on local soil and climatic conditions. Higher C inputs are required in wheat system of central United States and western Europe, mainly due to the higher current soil C stocks present in these regions. The critical C input could be effectively estimated using a summary model driven by current SOC level, mean annual temperature, precipitation, and soil clay content.

[Hygienic assessment of a recirculatory combined air-conditioning extract-and-input system in office building].

Science.gov (United States)

Malysheva, A G; Abramov, E G

2006-01-01

The high concentrations of lead were reveled in the air and dust of some premises and on the filters of a combined air-conditioning extract-and-input system in the high-rise office buildings located in the ecologically lead favorable environment. The dust content of lead in some premises on the first floors dust was as high as 200 mg/kg, which was more than 6 times higher than that in the soil at the highway near the office buildings. The use of new technologies and devices for cleaning and optimizing the air in the premises requires analytical studies to assess the quality of the environment, by taking into account the optimal conditions of their operation.

[Prosody, speech input and language acquisition].

Science.gov (United States)

Jungheim, M; Miller, S; Kühn, D; Ptok, M

2014-04-01

In order to acquire language, children require speech input. The prosody of the speech input plays an important role. In most cultures adults modify their code when communicating with children. Compared to normal speech this code differs especially with regard to prosody. For this review a selective literature search in PubMed and Scopus was performed. Prosodic characteristics are a key feature of spoken language. By analysing prosodic features, children gain knowledge about underlying grammatical structures. Child-directed speech (CDS) is modified in a way that meaningful sequences are highlighted acoustically so that important information can be extracted from the continuous speech flow more easily. CDS is said to enhance the representation of linguistic signs. Taking into consideration what has previously been described in the literature regarding the perception of suprasegmentals, CDS seems to be able to support language acquisition due to the correspondence of prosodic and syntactic units. However, no findings have been reported, stating that the linguistically reduced CDS could hinder first language acquisition.

Identification of efforts required for continued safe operation of KANUPP

International Nuclear Information System (INIS)

Ghafoor, M.A.; Hashmi, J.A.; Siddiqui, Z.H.

1991-01-01

Kanupp, the first commercial CANDU PHWR, rated at 137 MWe, was built on turnkey basis by the Canadian General Electric Company for the Pakistan Atomic Energy Commission, and went operational in October, 1972 near Karachi. It has operated since then with a lifetime average availability factor of 51.5% and capacity factor of 25%. In 1976, Kanupp suffered loss of technical support from its original vendors due to the Canadian embargo on export of nuclear technology. Simultaneously, the world experienced the most explosive development and advancement in electronic and computer technology, accelerating the obsolescence of such equipment and systems installed in Kanupp. Replacement upgrading of obsolete computers, control and instrumentation was thus the first major set of efforts realized as essential f or continued safe operation. On the other hand, Kanupp was able to cope with the normal maintenance of its process, mechanical and electrical equipment till the late 80's. But now many of these components are reaching the end of their useful life, and developing chronic problems due to ageing, which can only be solved by complete replacement. This is much more difficult for custom-made nuclear process equipment, e.g. the reactor internals and the fuelling machine. Public awareness and international concern about nuclear safety have increased significantly since the TMI and Chernobyl events. Corresponding realization of the critical role of human factors and the importance of operational experience feedback, has helped Kanupp by opening international channels of communication, including renewed cooperation on CANDU technology. The safety standards and criteria for CANDU as well as other NPPs have matured and evolved gradually over the past two decades. First Kanupp has to ensure that its present ageing-induced equipment problems are resolved to satisfy the original safety requirements and public risk targets which are still internationally acceptable. But as a policy, we

Identification of efforts required for continued safe operation of KANUPP

Energy Technology Data Exchange (ETDEWEB)

Ghafoor, M A; Hashmi, J A; Siddiqui, Z H [Karachi Nuclear Power Plant, Karachi (Pakistan)

1991-04-01

Kanupp, the first commercial CANDU PHWR, rated at 137 MWe, was built on turnkey basis by the Canadian General Electric Company for the Pakistan Atomic Energy Commission, and went operational in October, 1972 near Karachi. It has operated since then with a lifetime average availability factor of 51.5% and capacity factor of 25%. In 1976, Kanupp suffered loss of technical support from its original vendors due to the Canadian embargo on export of nuclear technology. Simultaneously, the world experienced the most explosive development and advancement in electronic and computer technology, accelerating the obsolescence of such equipment and systems installed in Kanupp. Replacement upgrading of obsolete computers, control and instrumentation was thus the first major set of efforts realized as essential f or continued safe operation. On the other hand, Kanupp was able to cope with the normal maintenance of its process, mechanical and electrical equipment till the late 80's. But now many of these components are reaching the end of their useful life, and developing chronic problems due to ageing, which can only be solved by complete replacement. This is much more difficult for custom-made nuclear process equipment, e.g. the reactor internals and the fuelling machine. Public awareness and international concern about nuclear safety have increased significantly since the TMI and Chernobyl events. Corresponding realization of the critical role of human factors and the importance of operational experience feedback, has helped Kanupp by opening international channels of communication, including renewed cooperation on CANDU technology. The safety standards and criteria for CANDU as well as other NPPs have matured and evolved gradually over the past two decades. First Kanupp has to ensure that its present ageing-induced equipment problems are resolved to satisfy the original safety requirements and public risk targets which are still internationally acceptable. But as a policy, we

Information Fusion of Conflicting Input Data

Directory of Open Access Journals (Sweden)

Uwe Mönks

2016-10-01

Full Text Available Sensors, and also actuators or external sources such as databases, serve as data sources in order to realise condition monitoring of industrial applications or the acquisition of characteristic parameters like production speed or reject rate. Modern facilities create such a large amount of complex data that a machine operator is unable to comprehend and process the information contained in the data. Thus, information fusion mechanisms gain increasing importance. Besides the management of large amounts of data, further challenges towards the fusion algorithms arise from epistemic uncertainties (incomplete knowledge in the input signals as well as conflicts between them. These aspects must be considered during information processing to obtain reliable results, which are in accordance with the real world. The analysis of the scientific state of the art shows that current solutions fulfil said requirements at most only partly. This article proposes the multilayered information fusion system MACRO (multilayer attribute-based conflict-reducing observation employing the μBalTLCS (fuzzified balanced two-layer conflict solving fusion algorithm to reduce the impact of conflicts on the fusion result. The performance of the contribution is shown by its evaluation in the scope of a machine condition monitoring application under laboratory conditions. Here, the MACRO system yields the best results compared to state-of-the-art fusion mechanisms. The utilised data is published and freely accessible.

Information Fusion of Conflicting Input Data.

Science.gov (United States)

Mönks, Uwe; Dörksen, Helene; Lohweg, Volker; Hübner, Michael

2016-10-29

Sensors, and also actuators or external sources such as databases, serve as data sources in order to realise condition monitoring of industrial applications or the acquisition of characteristic parameters like production speed or reject rate. Modern facilities create such a large amount of complex data that a machine operator is unable to comprehend and process the information contained in the data. Thus, information fusion mechanisms gain increasing importance. Besides the management of large amounts of data, further challenges towards the fusion algorithms arise from epistemic uncertainties (incomplete knowledge) in the input signals as well as conflicts between them. These aspects must be considered during information processing to obtain reliable results, which are in accordance with the real world. The analysis of the scientific state of the art shows that current solutions fulfil said requirements at most only partly. This article proposes the multilayered information fusion system MACRO (multilayer attribute-based conflict-reducing observation) employing the μ BalTLCS (fuzzified balanced two-layer conflict solving) fusion algorithm to reduce the impact of conflicts on the fusion result. The performance of the contribution is shown by its evaluation in the scope of a machine condition monitoring application under laboratory conditions. Here, the MACRO system yields the best results compared to state-of-the-art fusion mechanisms. The utilised data is published and freely accessible.

Can Simulation Credibility Be Improved Using Sensitivity Analysis to Understand Input Data Effects on Model Outcome?

Science.gov (United States)

Myers, Jerry G.; Young, M.; Goodenow, Debra A.; Keenan, A.; Walton, M.; Boley, L.

2015-01-01

Model and simulation (MS) credibility is defined as, the quality to elicit belief or trust in MS results. NASA-STD-7009 [1] delineates eight components (Verification, Validation, Input Pedigree, Results Uncertainty, Results Robustness, Use History, MS Management, People Qualifications) that address quantifying model credibility, and provides guidance to the model developers, analysts, and end users for assessing the MS credibility. Of the eight characteristics, input pedigree, or the quality of the data used to develop model input parameters, governing functions, or initial conditions, can vary significantly. These data quality differences have varying consequences across the range of MS application. NASA-STD-7009 requires that the lowest input data quality be used to represent the entire set of input data when scoring the input pedigree credibility of the model. This requirement provides a conservative assessment of model inputs, and maximizes the communication of the potential level of risk of using model outputs. Unfortunately, in practice, this may result in overly pessimistic communication of the MS output, undermining the credibility of simulation predictions to decision makers. This presentation proposes an alternative assessment mechanism, utilizing results parameter robustness, also known as model input sensitivity, to improve the credibility scoring process for specific simulations.

Electric Bike Sharing--System Requirements and Operational Concepts

Energy Technology Data Exchange (ETDEWEB)

Cherry, Christopher; Worley, Stacy; Jordan, David

2010-08-01

Bike sharing is an exciting new model of public-private transportation provision that has quickly emerged in the past five years. Technological advances have overcome hurdles of early systems and cities throughout the globe are adopting this model of transportation service. Electric bikes have simultaneously gained popularity in many regions of the world and some have suggested that shared electric bikes could provide an even higher level of service compared to existing systems. There are several challenges that are unique to shared electric bikes: electric-assisted range, recharging protocol, and bike and battery checkout procedures. This paper outlines system requirements to successfully develop and deploy an electric bike sharing system, focusing on system architecture, operational concepts, and battery management. Although there is little empirical evidence, electric bike sharing could be feasible, depending on demand and battery management, and can potentially improve the utility of existing bike sharing systems. Under most documented bike sharing use scenarios, electric bike battery capacity is insufficient for a full day of operation, depending on recharging protocol. Off-board battery management is a promising solution to address this problem. Off-board battery management can also support solar recharging. Future pilot tests will be important and allow empirical evaluation of electric bikesharing system performance. (auth)

Recurrent network models for perfect temporal integration of fluctuating correlated inputs.

Directory of Open Access Journals (Sweden)

Hiroshi Okamoto

2009-06-01

Full Text Available Temporal integration of input is essential to the accumulation of information in various cognitive and behavioral processes, and gradually increasing neuronal activity, typically occurring within a range of seconds, is considered to reflect such computation by the brain. Some psychological evidence suggests that temporal integration by the brain is nearly perfect, that is, the integration is non-leaky, and the output of a neural integrator is accurately proportional to the strength of input. Neural mechanisms of perfect temporal integration, however, remain largely unknown. Here, we propose a recurrent network model of cortical neurons that perfectly integrates partially correlated, irregular input spike trains. We demonstrate that the rate of this temporal integration changes proportionately to the probability of spike coincidences in synaptic inputs. We analytically prove that this highly accurate integration of synaptic inputs emerges from integration of the variance of the fluctuating synaptic inputs, when their mean component is kept constant. Highly irregular neuronal firing and spike coincidences are the major features of cortical activity, but they have been separately addressed so far. Our results suggest that the efficient protocol of information integration by cortical networks essentially requires both features and hence is heterotic.

Post-operative analgesic requirement in non-closure and closure of peritoneum during open appendectomy

International Nuclear Information System (INIS)

Khan, A.W.; Maqsood, R.; Saleem, M.M.

2017-01-01

To compare the mean post-operative analgesic requirement in non-closure and closure of peritoneum during open appendectomy. Study Design: Randomized controlled trial. Place and Duration of Study: Department of General Surgery Combined Military Hospital Quetta, from 1st August 2014 to 30th April 2015. Material and Methods: A total of 60 patients were included in this study and were divided into two groups of 30 each. Patients in group A underwent open appendectomy with closure of peritoneum while patients in group B had non-closure of peritoneum during the same procedure. Post-operatively, pain severity was assessed on visual analogue scale (VAS) numeric pain distress scale. On presence of VAS numeric pain distress scale between 5 to 7, intramuscular (IM) diclofenac sodium was given and on score >7, intravascular (IV) tramadol was given. The final outcome was measured at day 0 and day 1. Results: Pain score and analgesic requirements were significantly less in non-closure group than closure group on day 0 and day 1, showing statistically significant difference between the two groups. Conclusion: Mean post-operative analgesic requirement is significantly less in non-closure group as compared to closure group during open appendectomy. (author)

Development of an Input Model to MELCOR 1.8.5 for the Ringhals 3 PWR

International Nuclear Information System (INIS)

Nilsson, Lars

2004-12-01

An input file to the severe accident code MELCOR 1.8.5 has been developed for the Swedish pressurized water reactor Ringhals 3. The aim was to produce a file that can be used for calculations of various postulated severe accident scenarios, although the first application is specifically on cases involving large hydrogen production. The input file is rather detailed with individual modelling of all three cooling loops. The report describes the basis for the Ringhals 3 model and the input preparation step by step and is illustrated by nodalization schemes of the different plant systems. Present version of the report is restricted to the fundamental MELCOR input preparation, and therefore most of the figures of Ringhals 3 measurements and operating parameters are excluded here. These are given in another, complete version of the report, for limited distribution, which includes tables for pertinent data of all components. That version contains appendices with a complete listing of the input files as well as tables of data compiled from a RELAP5 file, that was a major basis for the MELCOR input for the cooling loops. The input was tested in steady-state calculations in order to simulate the initial conditions at current nominal operating conditions in Ringhals 3 for 2775 MW thermal power. The results of the steady-state calculations are presented in the report. Calculations with the MELCOR model will then be carried out of certain accident sequences for comparison with results from earlier MAAP4 calculations. That work will be reported separately

Risk based limits for Operational Safety Requirements

International Nuclear Information System (INIS)

Cappucci, A.J. Jr.

1993-01-01

OSR limits are designed to protect the assumptions made in the facility safety analysis in order to preserve the safety envelope during facility operation. Normally, limits are set based on ''worst case conditions'' without regard to the likelihood (frequency) of a credible event occurring. In special cases where the accident analyses are based on ''time at risk'' arguments, it may be desirable to control the time at which the facility is at risk. A methodology has been developed to use OSR limits to control the source terms and the times these source terms would be available, thus controlling the acceptable risk to a nuclear process facility. The methodology defines a new term ''gram-days''. This term represents the area under a source term (inventory) vs time curve which represents the risk to the facility. Using the concept of gram-days (normalized to one year) allows the use of an accounting scheme to control the risk under the inventory vs time curve. The methodology results in at least three OSR limits: (1) control of the maximum inventory or source term, (2) control of the maximum gram-days for the period based on a source term weighted average, and (3) control of the maximum gram-days at the individual source term levels. Basing OSR limits on risk based safety analysis is feasible, and a basis for development of risk based limits is defensible. However, monitoring inventories and the frequencies required to maintain facility operation within the safety envelope may be complex and time consuming

Network interactions: non-geniculate input to V1.

Science.gov (United States)

Muckli, Lars; Petro, Lucy S

2013-04-01

The strongest connections to V1 are fed back from neighbouring area V2 and from a network of higher cortical areas (e.g. V3, V5, LOC, IPS and A1), transmitting the results of cognitive operations such as prediction, attention and imagination. V1 is therefore at the receiving end of a complex cortical processing cascade and not only at the entrance stage of cortical processing of retinal input. One elegant strategy to investigate this information-rich feedback to V1 is to eliminate feedforward input, that is, exploit V1's retinotopic organisation to isolate subregions receiving no direct bottom-up stimulation. We highlight the diverse mechanisms of cortical feedback, ranging from gain control to predictive coding, and conclude that V1 is involved in rich internal communication processes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Efficiency of PRECIS Role Operators.

Science.gov (United States)

Mahapatra, M.; Biswas, S. C.

1984-01-01

Describes research which measured the efficiency of role operators through frequency of appearances in PRECIS input strings for 200 abstracts related to taxation, genetic psychology, and Shakespearian drama. Frequencies of appearance of major categories of role operators, role operators in different subjects, individual main line operators, and…

Report on task 4.1.3. - Survey of anticipated functional requirement for operator support systems

International Nuclear Information System (INIS)

Silvani, V.

1993-01-01

This is a preliminary report summarizing some topics related to the surveillance activity on anticipated functional requirements of the Operator Support Systems (OSS's) in NPP's. Additional information are expected will be available by analyzing the questionnaire. Functionalities examined are those referring to system functions, user's needs, technology trend, standard status. For practical purposes this document is divided in two main sections: the first section presents a summary of major OSS requirements and related problems as derived from the existing literature; the second section presents a study of OSS to be used to support the operator training presently under development in ENEA. Finally, appendix 2 reports a summary of major functions performed by the OSS's presently in operation or under development in laboratories. Refs, 1 tab

Mission reliability of semi-Markov systems under generalized operational time requirements

International Nuclear Information System (INIS)

Wu, Xiaoyue; Hillston, Jane

2015-01-01

Mission reliability of a system depends on specific criteria for mission success. To evaluate the mission reliability of some mission systems that do not need to work normally for the whole mission time, two types of mission reliability for such systems are studied. The first type corresponds to the mission requirement that the system must remain operational continuously for a minimum time within the given mission time interval, while the second corresponds to the mission requirement that the total operational time of the system within the mission time window must be greater than a given value. Based on Markov renewal properties, matrix integral equations are derived for semi-Markov systems. Numerical algorithms and a simulation procedure are provided for both types of mission reliability. Two examples are used for illustration purposes. One is a one-unit repairable Markov system, and the other is a cold standby semi-Markov system consisting of two components. By the proposed approaches, the mission reliability of systems with time redundancy can be more precisely estimated to avoid possible unnecessary redundancy of system resources. - Highlights: • Two types of mission reliability under generalized requirements are defined. • Equations for both types of reliability are derived for semi-Markov systems. • Numerical methods are given for solving both types of reliability. • Simulation procedure is given for estimating both types of reliability. • Verification of the numerical methods is given by the results of simulation

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

Documentation of compliance with the energy performance regulations at the end of the detailed design phase is mandatory for building owners in Denmark. Therefore, besides multidisciplinary input, the building design process requires various iterative analyses, so that the optimal solutions can....... That has left the industry in constant pursuit of possibilities for integration of the tool within the Building Information Modelling environment so that the potential provided by the latter can be harvested and the processed can be optimized. This paper presents a solution for automated data extraction...... from building geometry created in Autodesk Revit and its translation to input for compliance check analysis....

Engineering to Control Noise, Loading, and Optimal Operating Points

International Nuclear Information System (INIS)

Mitchell R. Swartz

2000-01-01

Successful engineering of low-energy nuclear systems requires control of noise, loading, and optimum operating point (OOP) manifolds. The latter result from the biphasic system response of low-energy nuclear reaction (LENR)/cold fusion systems, and their ash production rate, to input electrical power. Knowledge of the optimal operating point manifold can improve the reproducibility and efficacy of these systems in several ways. Improved control of noise, loading, and peak production rates is available through the study, and use, of OOP manifolds. Engineering of systems toward the OOP-manifold drive-point peak may, with inclusion of geometric factors, permit more accurate uniform determinations of the calibrated activity of these materials/systems

18 CFR 376.209 - Procedures during periods of emergency requiring activation of the Continuity of Operations Plan.

Science.gov (United States)

2010-04-01

... periods of emergency requiring activation of the Continuity of Operations Plan. 376.209 Section 376.209... of the Continuity of Operations Plan. (a)(1) The Commission's Continuity of Operations Plan is...) During periods when the Continuity of Operations Plan is activated, the Commission will continue to act...

21 CFR 111.355 - What are the design requirements for manufacturing operations?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What are the design requirements for manufacturing operations? 111.355 Section 111.355 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION CURRENT GOOD MANUFACTURING PRACTICE IN...

Environmental Molecular Sciences Laboratory Operations System: Version 4.0 - system requirements specification

Energy Technology Data Exchange (ETDEWEB)

Kashporenko, D.

1996-07-01

This document is intended to provide an operations standard for the Environmental Molecular Sciences Laboratory OPerations System (EMSL OPS). It is directed toward three primary audiences: (1) Environmental Molecular Sciences Laboratory (EMSL) facility and operations personnel; (2) laboratory line managers and staff; and (3) researchers, equipment operators, and laboratory users. It is also a statement of system requirements for software developers of EMSL OPS. The need for a finely tuned, superior research environment as provided by the US Department of Energy`s (DOE) Environmental Molecular Sciences Laboratory has never been greater. The abrupt end of the Cold War and the realignment of national priorities caused major US and competing overseas laboratories to reposition themselves in a highly competitive research marketplace. For a new laboratory such as the EMSL, this means coming into existence in a rapidly changing external environment. For any major laboratory, these changes create funding uncertainties and increasing global competition along with concomitant demands for higher standards of research product quality and innovation. While more laboratories are chasing fewer funding dollars, research ideas and proposals, especially for molecular-level research in the materials and biological sciences, are burgeoning. In such an economically constrained atmosphere, reduced costs, improved productivity, and strategic research project portfolio building become essential to establish and maintain any distinct competitive advantage. For EMSL, this environment and these demands require clear operational objectives, specific goals, and a well-crafted strategy. Specific goals will evolve and change with the evolution of the nature and definition of DOE`s environmental research needs. Hence, EMSL OPS is designed to facilitate migration of these changes with ease into every pertinent job function, creating a facile {open_quotes}learning organization.{close_quotes}

Requirements on the mechanical design of reactor systems operating at elevated temperature

International Nuclear Information System (INIS)

Schulz, H.; Glahn, M.

1979-01-01

The paper presents the contemporary status of the requirements on the mechanical design and analysis developed during the licensing procedure of reactor systems operating at elevated temperature. General requirements for the design at elevated temperature are reviewed. The main proposal is to point out some limit strain criteria which are not included in present design guidelines and codes. The developed strain criteria are used to limit the component deformations in case of power excursions like the Bethe-Tait accident. It is also applicable for loads arising from other faulted conditions. (orig.)

Input parameters to codes which analyze LMFBR wire-wrapped bundles

International Nuclear Information System (INIS)

Hawley, J.T.; Chan, Y.N.; Todreas, N.E.

1980-12-01

This report provides a current summary of recommended values of key input parameters required by ENERGY code analysis of LMFBR wire wrapped bundles. This data is based on the interpretation of experimental results from the MIT and other available laboratory programs

Input modeling with phase-type distributions and Markov models theory and applications

CERN Document Server

Buchholz, Peter; Felko, Iryna

2014-01-01

Containing a summary of several recent results on Markov-based input modeling in a coherent notation, this book introduces and compares algorithms for parameter fitting and gives an overview of available software tools in the area. Due to progress made in recent years with respect to new algorithms to generate PH distributions and Markovian arrival processes from measured data, the models outlined are useful alternatives to other distributions or stochastic processes used for input modeling. Graduate students and researchers in applied probability, operations research and computer science along with practitioners using simulation or analytical models for performance analysis and capacity planning will find the unified notation and up-to-date results presented useful. Input modeling is the key step in model based system analysis to adequately describe the load of a system using stochastic models. The goal of input modeling is to find a stochastic model to describe a sequence of measurements from a real system...

A Novel Coupled State/Input/Parameter Identification Method for Linear Structural Systems

Directory of Open Access Journals (Sweden)

Zhimin Wan

2018-01-01

Full Text Available In many engineering applications, unknown states, inputs, and parameters exist in the structures. However, most methods require one or two of these variables to be known in order to identify the other(s. Recently, the authors have proposed a method called EGDF for coupled state/input/parameter identification for nonlinear system in state space. However, the EGDF method based solely on acceleration measurements is found to be unstable, which can cause the drift of the identified inputs and displacements. Although some regularization methods can be adopted for solving the problem, they are not suitable for joint input-state identification in real time. In this paper, a strategy of data fusion of displacement and acceleration measurements is used to avoid the low-frequency drift in the identified inputs and structural displacements for linear structural systems. Two numerical examples about a plane truss and a single-stage isolation system are conducted to verify the effectiveness of the proposed modified EGDF algorithm.

Man/machine interface for a nuclear cask remote handling control station: system design requirements

International Nuclear Information System (INIS)

Clarke, M.M.; Kreifeldt, J.G.; Draper, J.V.

1984-01-01

Design requirements are presented for a control station of a proposed semi-automated facility for remote handling of nuclear waste casks. Functional and operational man/machine interface: controls, displays, software format, station architecture, and work environment. In addition, some input is given to the design of remote sensing systems in the cask handling areas. 18 references, 9 figures, 12 tables

Health requirements for nuclear reactor operators

International Nuclear Information System (INIS)

1980-05-01

The health prerequisites established for the qualification of nuclear reactor operators according to CNEN-NE-1.01 Guidelines Licensing of nuclear reactor operators, CNEN-12/79 Resolution, are described. (M.A.) [pt

High-Level Functional and Operational Requirements for the Advanced Fuel Cycle Facility

International Nuclear Information System (INIS)

Charles Park

2006-01-01

This document describes the principal functional and operational requirements for the proposed Advanced Fuel Cycle Facility (AFCF). The AFCF is intended to be the world's foremost facility for nuclear fuel cycle research, technology development, and demonstration. The facility will also support the near-term mission to develop and demonstrate technology in support of fuel cycle needs identified by industry, and the long-term mission to retain and retain U.S. leadership in fuel cycle operations. The AFCF is essential to demonstrate a more proliferation-resistant fuel cycle and make long-term improvements in fuel cycle effectiveness, performance and economy

Existing pavement input information for the mechanistic-empirical pavement design guide.

Science.gov (United States)

2009-02-01

The objective of this study is to systematically evaluate the Iowa Department of Transportations (DOTs) existing Pavement Management Information System (PMIS) with respect to the input information required for Mechanistic-Empirical Pavement Des...

Requirements for the authorization of operation os a calibration laboratory of gamma-ray monitors

International Nuclear Information System (INIS)

Silva, Raimundo Dias da; Kibrit, Eduardo

2011-01-01

This paper describes the process for obtaining the authorization of operation of a laboratory designed to calibrate area and personal monitors with gamma radiation, by using a sealed Cs-137 source. The regulations of Comissao Nacional de Energia Nuclear (CNEN) are deeply analysed and discussed. The authorization for construction, the authorization for modification of items important to safety, the authorization for the acquisition and handling of radiation sources, the authorization for operating, and the authorization for withdrawal of operation of the laboratory are also discussed. The paper also describes the technical and managerial requirements necessary to operate a gamma radiation calibration laboratory in Brazil. . (author)

45 CFR 307.10 - Functional requirements for computerized support enforcement systems in operation by October 1...

Science.gov (United States)

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false Functional requirements for computerized support... ENFORCEMENT SYSTEMS § 307.10 Functional requirements for computerized support enforcement systems in operation... necessary to meet Federal Reporting Requirements on a timely basis as prescribed by the Office; (4...

Regulatory quality assurance requirements for the operation of nuclear R and D facilities in Korea

International Nuclear Information System (INIS)

Kwon, H.I.; Lim, N.J.

2006-01-01

Full text: Korea Atomic Energy Research Institute (KAERI) has many R and D facilities in operation. including HANARO research reactor, radioactive waste treatment facility (RWTF), post-irradiation examination facility (PIEF) and irradiated material test facility (IMEF). Recently. nation-wide interest is focused on the safety and security of major industrial facilities. Safe operation of nuclear facilities is imperative because of the consequence of public disaster by radiological release/contamination, in case of an accident. Recently, Ministry of Science and Technology (MOST) of the Korean government announced amendments of Atomic Energy laws to enforce requirements of the physical protection and radiological emergency. All provisions on nuclear safety regulation and radiation protection are entrusted to the Atomic Energy Act(AEA). The Act is enacted as the main law concerning the safety regulation of nuclear installations, and is supplemented by the Enforcement Decree and Enforcement Regulation of the Act. These Atomic Energy laws include provisions on the construction permission and the operation license of nuclear installations, such as nuclear power reactors, research reactors, nuclear ships, nuclear fuel fabrication facilities, spent fuel treatment facilities, etc. Regulatory requirements for the regulatory inspection and the safety measures for operation are also defined in the laws. The Notice of the MOST prescribes specific issues including regulatory requirements and technical standards, as entrusted by the AEA, the Decree and the Regulation. Detailed QA requirements for nuclear installations are specified differently, depending upon the type of facility. The guidelines for safety reviews and regulatory inspections are developed by the Korea Institute of Nuclear Safety (KINS), which is an exclusive organization for safety regulation of nuclear installations in Korea. In this paper, the context of the Atomic Energy laws were reviewed to confirm the

Requirements Analysis Study for Master Pump Shutdown System Project Development Specification [SEC 1 and 2

International Nuclear Information System (INIS)

BEVINS, R.R.

2000-01-01

This document has been updated during the definitive design portion of the first phase of the W-314 Project to capture additional software requirements and is planned to be updated during the second phase of the W-314 Project to cover the second phase of the Project's scope. The objective is to provide requirement traceability by recording the analysis/basis for the functional descriptions of the master pump shutdown system. This document identifies the sources of the requirements and/or how these were derived. Each requirement is validated either by quoting the source or an analysis process involving the required functionality, performance characteristics, operations input or engineering judgment

77 FR 11995 - Passenger Vessel Operator Financial Responsibility Requirements for Non-Performance of...

Science.gov (United States)

2012-02-28

... Vessel Operator Financial Responsibility Requirements for Non-Performance of Transportation AGENCY..., 2011, the Commission issued its Notice of Proposed Rulemaking (NPRM) to update its financial... cost of financial responsibility coverage because of the use of alternative coverage options. However...

Westinghouse corporate development of a decision software program for Radiological Evaluation Decision Input (REDI)

International Nuclear Information System (INIS)

Bush, T.S.

1995-01-01

In December 1992, the Department of Energy (DOE) implemented the DOE Radiological Control Manual (RCM). Westinghouse Idaho Nuclear Company, Inc. (WINCO) submitted an implementation plan showing how compliance with the manual would be achieved. This implementation plan was approved by DOE in November 1992. Although WINCO had already been working under a similar Westinghouse RCM, the DOE RCM brought some new and challenging requirements. One such requirement was that of having procedure writers and job planners create the radiological input in work control procedures. Until this time, that information was being provided by radiological engineering or a radiation safety representative. As a result of this requirement, Westinghouse developed the Radiological Evaluation Decision Input (REDI) program

Westinghouse corporate development of a decision software program for Radiological Evaluation Decision Input (REDI)

Energy Technology Data Exchange (ETDEWEB)

Bush, T.S. [Westinghosue Idaho Nuclear Co., Inc., Idaho Falls, ID (United States)

1995-03-01

In December 1992, the Department of Energy (DOE) implemented the DOE Radiological Control Manual (RCM). Westinghouse Idaho Nuclear Company, Inc. (WINCO) submitted an implementation plan showing how compliance with the manual would be achieved. This implementation plan was approved by DOE in November 1992. Although WINCO had already been working under a similar Westinghouse RCM, the DOE RCM brought some new and challenging requirements. One such requirement was that of having procedure writers and job planners create the radiological input in work control procedures. Until this time, that information was being provided by radiological engineering or a radiation safety representative. As a result of this requirement, Westinghouse developed the Radiological Evaluation Decision Input (REDI) program.

Facilitating mathematics learning for students with upper extremity disabilities using touch-input system.

Science.gov (United States)

Choi, Kup-Sze; Chan, Tak-Yin

2015-03-01

To investigate the feasibility of using tablet device as user interface for students with upper extremity disabilities to input mathematics efficiently into computer. A touch-input system using tablet device as user interface was proposed to assist these students to write mathematics. User-switchable and context-specific keyboard layouts were designed to streamline the input process. The system could be integrated with conventional computer systems only with minor software setup. A two-week pre-post test study involving five participants was conducted to evaluate the performance of the system and collect user feedback. The mathematics input efficiency of the participants was found to improve during the experiment sessions. In particular, their performance in entering trigonometric expressions by using the touch-input system was significantly better than that by using conventional mathematics editing software with keyboard and mouse. The participants rated the touch-input system positively and were confident that they could operate at ease with more practice. The proposed touch-input system provides a convenient way for the students with hand impairment to write mathematics and has the potential to facilitate their mathematics learning. Implications for Rehabilitation Students with upper extremity disabilities often face barriers to learning mathematics which is largely based on handwriting. Conventional computer user interfaces are inefficient for them to input mathematics into computer. A touch-input system with context-specific and user-switchable keyboard layouts was designed to improve the efficiency of mathematics input. Experimental results and user feedback suggested that the system has the potential to facilitate mathematics learning for the students.

VHF Series-Input Parallel-Output Interleaved Self-Oscillating Resonant SEPIC Converter

DEFF Research Database (Denmark)

Kovacevic, Milovan; Knott, Arnold; Andersen, Michael A. E.

2013-01-01

If the switches of two resonant SEPIC converters are capacitively coupled, it is possible to obtain a self-oscillating converter in which the two power stages operate in interleaved mode. This paper describes a topology where the inputs of two SEPIC converters are connected in series, thereby sha...

Three-input gate logic circuits on chemically assembled single-electron transistors with organic and inorganic hybrid passivation layers.

Science.gov (United States)

Majima, Yutaka; Hackenberger, Guillaume; Azuma, Yasuo; Kano, Shinya; Matsuzaki, Kosuke; Susaki, Tomofumi; Sakamoto, Masanori; Teranishi, Toshiharu

2017-01-01

Single-electron transistors (SETs) are sub-10-nm scale electronic devices based on conductive Coulomb islands sandwiched between double-barrier tunneling barriers. Chemically assembled SETs with alkanethiol-protected Au nanoparticles show highly stable Coulomb diamonds and two-input logic operations. The combination of bottom-up and top-down processes used to form the passivation layer is vital for realizing multi-gate chemically assembled SET circuits, as this combination enables us to connect conventional complementary metal oxide semiconductor (CMOS) technologies via planar processes. Here, three-input gate exclusive-OR (XOR) logic operations are demonstrated in passivated chemically assembled SETs. The passivation layer is a hybrid bilayer of self-assembled monolayers (SAMs) and pulsed laser deposited (PLD) aluminum oxide (AlO[Formula: see text]), and top-gate electrodes were prepared on the hybrid passivation layers. Top and two-side-gated SETs showed clear Coulomb oscillation and diamonds for each of the three available gates, and three-input gate XOR logic operation was clearly demonstrated. These results show the potential of chemically assembled SETs to work as logic devices with multi-gate inputs using organic and inorganic hybrid passivation layers.

Accuracy Enhancement for Forecasting Water Levels of Reservoirs and River Streams Using a Multiple-Input-Pattern Fuzzification Approach

Directory of Open Access Journals (Sweden)

Nariman Valizadeh

2014-01-01

Full Text Available Water level forecasting is an essential topic in water management affecting reservoir operations and decision making. Recently, modern methods utilizing artificial intelligence, fuzzy logic, and combinations of these techniques have been used in hydrological applications because of their considerable ability to map an input-output pattern without requiring prior knowledge of the criteria influencing the forecasting procedure. The artificial neurofuzzy interface system (ANFIS is one of the most accurate models used in water resource management. Because the membership functions (MFs possess the characteristics of smoothness and mathematical components, each set of input data is able to yield the best result using a certain type of MF in the ANFIS models. The objective of this study is to define the different ANFIS model by applying different types of MFs for each type of input to forecast the water level in two case studies, the Klang Gates Dam and Rantau Panjang station on the Johor river in Malaysia, to compare the traditional ANFIS model with the new introduced one in two different situations, reservoir and stream, showing the new approach outweigh rather than the traditional one in both case studies. This objective is accomplished by evaluating the model fitness and performance in daily forecasting.

Accuracy enhancement for forecasting water levels of reservoirs and river streams using a multiple-input-pattern fuzzification approach.

Science.gov (United States)

Valizadeh, Nariman; El-Shafie, Ahmed; Mirzaei, Majid; Galavi, Hadi; Mukhlisin, Muhammad; Jaafar, Othman

2014-01-01

Water level forecasting is an essential topic in water management affecting reservoir operations and decision making. Recently, modern methods utilizing artificial intelligence, fuzzy logic, and combinations of these techniques have been used in hydrological applications because of their considerable ability to map an input-output pattern without requiring prior knowledge of the criteria influencing the forecasting procedure. The artificial neurofuzzy interface system (ANFIS) is one of the most accurate models used in water resource management. Because the membership functions (MFs) possess the characteristics of smoothness and mathematical components, each set of input data is able to yield the best result using a certain type of MF in the ANFIS models. The objective of this study is to define the different ANFIS model by applying different types of MFs for each type of input to forecast the water level in two case studies, the Klang Gates Dam and Rantau Panjang station on the Johor river in Malaysia, to compare the traditional ANFIS model with the new introduced one in two different situations, reservoir and stream, showing the new approach outweigh rather than the traditional one in both case studies. This objective is accomplished by evaluating the model fitness and performance in daily forecasting.

Operative intercostal chest drain is not required following extrapleural or transpleural esophageal atresia repair.

Science.gov (United States)

Paramalingam, Saravanakumar; Burge, David M; Stanton, Michael P

2013-08-01

Approximately half of the United Kingdom patients undergoing esophageal atresia (OA) repair have an operative intercostal chest drain (ICD) placed (2008 British Association of Pediatric Surgeons Congenital Anomalies Surveillance Study data). We reviewed our experience of OA repairs to evaluate if an ICD placement is necessary. Patients with OA/distal tracheoesophageal fistula (TOF), treated between January 1990 and January 2010, were identified by retrospective review of a prospectively maintained electronic database and patient case notes. A total of 112 consecutive patients were identified, of whom 107 were included (73 male). Five were excluded as no case notes were available. Median birth weight was 2,597 g (range 924 to 4,245 g) and median gestational age was 38 weeks (27 to 41 weeks). Median age at discharge was 22 days (3 to 440 days) and median follow-up was 3.5 years (0 to 18 years). Patients were analyzed in two groups-group 1 (n = 73) had an extrapleural (EP) repair, of which 23 had a pleural breach and group 2 (n = 34) had a purposeful transpleural (TP) approach (surgeon preference). Eleven patients (10%) had an operative ICD, of which six patients were in group 1 and five in group 2. These 11 patients had an uncomplicated postoperative course and all operative ICD were removed within 48 hours of surgery. Of the 96 patients that did not have an operative ICD, only 2 (2%) required postoperative intervention. One patient, in group 2, had a postoperative ICD inserted for a simple pneumothorax at 12 hours and removed at 48 hours. The other patient, in group 1, had a clinically detected anastomotic leak after 48 hours and required operative repair. An operative ICD is not required following OA/distal TOF repair, whether the approach is EP or TP. ICD that were electively placed (in 10%) served no clinical purpose. Georg Thieme Verlag KG Stuttgart · New York.

Evaluation of Maximum a Posteriori Estimation as Data Assimilation Method for Forecasting Infiltration-Inflow Affected Urban Runoff with Radar Rainfall Input

DEFF Research Database (Denmark)

Wied Pedersen, Jonas; Lund, Nadia Schou Vorndran; Borup, Morten

2016-01-01

High quality on-line flow forecasts are useful for real-time operation of urban drainage systems and wastewater treatment plants. This requires computationally efficient models, which are continuously updated with observed data to provide good initial conditions for the forecasts. This paper...... period of time that precedes the forecast. The method is illustrated for an urban catchment, where flow forecasts of 0–4 h are generated by applying a lumped linear reservoir model with three cascading reservoirs. Radar rainfall observations are used as input to the model. The effects of different prior...

Requirements for Computer Based-Procedures for Nuclear Power Plant Field Operators. Results from a Qualitative Study

International Nuclear Information System (INIS)

Le Blanc, Katya; Oxstrand, J.H.; Waicosky, T.

2012-01-01

Although computer-based procedures (CBPs) have been investigated as a way to enhance operator performance on procedural tasks in the nuclear industry for almost thirty years, they are not currently widely deployed at United States utilities. One of the barriers to the wide scale deployment of CBPs is the lack of operational experience with CBPs that could serve as a sound basis for justifying the use of CBPs for nuclear utilities. Utilities are hesitant to adopt CBPs because of concern over potential costs of implementation, and concern over regulatory approval. Regulators require a sound technical basis for the use of any procedure at the utilities; without operating experience to support the use CBPs, it is difficult to establish such a technical basis. In an effort to begin the process of developing a technical basis for CBPs, researchers at Idaho National Laboratory are partnering with industry to explore CBPs with the objective of defining requirements for CBPs and developing an industry-wide vision and path forward for the use of CBPs. This paper describes the results from a qualitative study aimed at defining requirements for CBPs to be used by field operators and maintenance technicians. (author)

Load following operation of nuclear power plants for meeting power system requirements

International Nuclear Information System (INIS)

Isoda, Hachiro

1987-01-01

This paper describes a calculating program on the availability factors of nuclear, thermal and pumed storage hydro power stations and some calculated results for typical three load factors, 55 %, 60 % and 71 %, are provided when the share of the nuclea power station in the generation facilities is increased. The load following requirement of the nuclear power station is also provided. Load following requirement: If there is a 10 % pumped storage hydro power station, the nuclear power station enables to be operated with its rated output up to 30 % - 35 % of its share. Its daily load following operation for 40 % and 50 % nuclear power station needs every weekend and every day respectively. Availability factor: The availability factor of the nuclear power station manages to get 80 % (maximum availability factor of the nuclear power station in this study) up to 30 % share of it with 10 % pumpued storage hydro power station. When the nuclear power station shares 40 % and 50 %, its availability factor decreases down 1 % and 5 % respectively. (author)

Real Time Part Input Control of a Pull Production System by Finding IF-THEN Rules

Science.gov (United States)

Ramli, Rizauddin; Yamamoto, Hidehiko; Abu Qudeiri, Jaber

This paper considers the part input problem of a production system where two Flexible Transfer Lines (FTLs) consisting of an up-stream production line and a down-stream production line while operating under Just In Time (JIT) production management. The up-stream production line processes the raw material after receiving them from suppliers, and after processing them, delivers the processed product to a down-stream production line via a conveyer. In this paper, we have proposed a novel idea for a part input real time control system, known as Algorithm for Real Time Control of Part Input Systems (ARTCOPS). The algorithm is useful when FTLs are in operation under a production order that is different from the pre-decided production schedule. Simulations of virtual production systems have been carried out to verify that ARTCOPS is useful in real time control, although the production orders are different from the pre-decided production scheduling.

Task analysis: How far are we from usable PRA input

International Nuclear Information System (INIS)

Gertman, D.I.; Blackman, H.S.; Hinton, M.F.

1984-01-01

This chapter reviews data collected at the Idaho National Engineering Laboratory for three DOE-owned reactors (the Advanced Test Reactor, the Power Burst Facility, and the Loss of Fluids Test Reactor) in order to identify usable Probabilistic Risk Assessment (PRA) input. Task analytic procedures involve the determination of manning and skill levels as a means of determining communication requirements, in assessing job performance aids, and in assessing the accuracy and completeness of emergency and maintenance procedures. The least understood aspect in PRA and plant reliability models is the human factor. A number of examples from the data base are discussed and offered as a means of providing more meaningful data than has been available to PRA analysts in the past. It is concluded that the plant hardware-procedures-personnel interfaces are essential to safe and efficient plant operations and that task analysis is a reasonably sound way of achieving a qualitative method for identifying those tasks most strongly associated with task difficulty, severity of consequence, and error probability

Reactor operation plan preparing device

International Nuclear Information System (INIS)

Sano, Hiroki; Maruyama, Hiromi; Kinoshita, Mitsuo; Fukuzaki, Koji; Banto, Masaru; Fukazawa, Yukihisa.

1993-01-01

The device comprises a means for retrieving a control rod pattern capable of satisfying a thermal limit upon aimed power/minimum flow rate and providing minimum xenon and a control rod pattern maximum xenon. It further comprises a means for selecting a control rod pattern corresponding to a xenon equilibrium condition, and selecting a control rod which provides a greater thermal margin to provide a control rod operation sequence for each of the patterns. Further, the device comprises an outline plan preparing means and a correction means therefor, a simplified sequence table reference means operated along with sequence change, an operation limit region input means, a control rod operation preferential region changing means, a thermal margin evaluation region and an input means. This can automatically prepare the operation plan, decrease the times for preparation of detailed plans by using the outline plan preparing function, thereby enabling to remarkably shorten the time for preparing of an operation plan. (N.H.)

Meteorological requirements and operational fallout prediction techniques for Plowshare nuclear detonations

International Nuclear Information System (INIS)

Mueller, H.F.

1969-01-01

Meteorological support requirements for Plowshare nuclear detonations are shown to depend on a number of factors. The importance of adequate support to the effective planning and safe conduct of a nuclear detonation is described. An example of the influence of atmospheric conditions on radioactive cloud development and local transport and fallout of radioactive debris is presented. Prediction of the future state of atmospheric wind structure, required for fallout predictions depends on an adequate definition of its initial state and its rate of change. This definition, in turn, is shown to depend on an upper wind-sounding network of appropriate station density. An operational technique currently used for nuclear cratering fallout predictions is described and shown to produce results of useful accuracy. (author)

Meteorological requirements and operational fallout prediction techniques for Plowshare nuclear detonations

Energy Technology Data Exchange (ETDEWEB)

Mueller, H F [Air Resources Laboratory, Environmental Science Services Administration, Las Vegas, NV (United States)

1969-07-01

Meteorological support requirements for Plowshare nuclear detonations are shown to depend on a number of factors. The importance of adequate support to the effective planning and safe conduct of a nuclear detonation is described. An example of the influence of atmospheric conditions on radioactive cloud development and local transport and fallout of radioactive debris is presented. Prediction of the future state of atmospheric wind structure, required for fallout predictions depends on an adequate definition of its initial state and its rate of change. This definition, in turn, is shown to depend on an upper wind-sounding network of appropriate station density. An operational technique currently used for nuclear cratering fallout predictions is described and shown to produce results of useful accuracy. (author)

Operation control device under radiation exposure

International Nuclear Information System (INIS)

Kimura, Kiichi; Murakami, Toichi.

1994-01-01

The device of the present invention performs smooth progress of operation by remote control for a plurality of operations in periodical inspections in controlled areas of a nuclear power plant, thereby reducing the operator's exposure dose. Namely, the device monitors the progressing state of the operation by displaying the progress of operation on a CRT of a centralized control device present in a low dose area remote from an operation field through an ITV camera disposed in the vicinity of the operation field. Further, operation sequence and operation instruction procedures previously inputted in the device are indicated to the operation field through an operation instruction outputting device (field CRT) in accordance with the progress of the operation steps. On the other hand, the operation progress can be aided by inputting information from the operation field such as start or completion of the operation steps. Further, the device of the present invention can monitor the change of operation circumstances and exposure dose of operators based on the information from a radiation dose measuring device disposed in the operation circumstance and to individual operators. (I.S.)

Effects of modulation techniques on the input current interharmonics of Adjustable Speed Drives

DEFF Research Database (Denmark)

Soltani, Hamid; Davari, Pooya; Zare, Firuz

2018-01-01

operation of the grid. This paper presents the effect of the symmetrical regularly sampled Space Vector Modulation (SVM) and Discontinuous Pulse Width Modulation-30olag (DPWM2) techniques, as the most popular modulation methods in the ASD applications, on the drive’s input current interharmonic magnitudes....... Further investigations are also devoted to the cases, where the Random Modulation (RM) technique is applied on the selected modulation strategies. The comparative results show that how different modulation techniques can influence the ASD’s input current interharmonics and consequently may...

42 CFR 84.146 - Method of measuring the power and torque required to operate blowers.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Method of measuring the power and torque required... RESPIRATORY PROTECTIVE DEVICES Supplied-Air Respirators § 84.146 Method of measuring the power and torque.... These are used to facilitate timing. To determine the torque or horsepower required to operate the...

PLEXOS Input Data Generator

Energy Technology Data Exchange (ETDEWEB)

2017-02-01

The PLEXOS Input Data Generator (PIDG) is a tool that enables PLEXOS users to better version their data, automate data processing, collaborate in developing inputs, and transfer data between different production cost modeling and other power systems analysis software. PIDG can process data that is in a generalized format from multiple input sources, including CSV files, PostgreSQL databases, and PSS/E .raw files and write it to an Excel file that can be imported into PLEXOS with only limited manual intervention.

Ovariohysterectomy requires more post-operative analgesia than orchiectomy in dogs and cats.

Science.gov (United States)

Quarterone, Carolina; Luna, Stelio Pacca Loureiro; Crosignani, Nadia; de Oliveira, Flávia Augusta; Lopes, Carlize; da Maia Lima, Alfredo Feio; de Araújo Aguiar, Antonio Jose

2017-11-01

The requirement for post-operative analgesia after ovariohysterectomy (OH) versus orchiectomy in dogs and cats was compared. Twelve male and 12 female cats and 12 male and 12 female dogs received meloxicam, 0.1 mg/kg body weight, PO, 2 h before surgery. Eleven female cats and 3 female dogs received rescue analgesia ( P = 0.002). No male of either species required rescue analgesia. The number of cats receiving rescue analgesia was greater in females than in males ( P dogs or cats. Postoperative pain after OH should be assessed for at least 2 h for cats and 4 h for dogs, using species-specific validated tools, to ensure proper postoperative pain diagnosis and management. Male dogs and cats subjected to orchiectomy required less postoperative analgesia intervention than female dogs and cats submitted to OH.

Implementation of the Save and Restoration application for KOMAC operation

Energy Technology Data Exchange (ETDEWEB)

Kim, Jae-Ha; Song, Young-Gi; Kwon, Hyeok-Jung; Cho, Yong-Sub [Korea Atomic Energy Research Institute, Gyeongju (Korea, Republic of)

2016-10-15

KOMAC has been operating a 100 MeV proton linear Accelerator. There are about 10,000 PVs for operating the 100 MeV proton linac. It is important to archive the operating parameters for operating beam lines and machine study. The parameters are reported manually and with screenshot. There not fixed reporting type so it is difficult to compare archived data. To improve and compensate the reporting system, a Save and Restoration application, which is based on JAVA has been implemented and connected with KOMAC Control system based on EPICS with JCA library. The operating data are saved in Save and Restoration Server in file type, and are restored to the required values using the saved files. This paper presents Implementation of the Save and Restoration application and its function. The group list is shown in restore page using reload button. The saved value of the PVs in group is shown as selecting a group which clients require and current values are appeared beside the restore value table to compare with saved data. The set restore button input the values in restore value table to each PV. The Save and Restore application save and restore the value of the PVs that clients require. The application is installed in client PC but data are archived in save and restore server in file format.

RDS - A systematic approach towards system thermal hydraulics input code development for a comprehensive deterministic safety analysis

International Nuclear Information System (INIS)

Salim, Mohd Faiz; Roslan, Ridha; Ibrahim, Mohd Rizal Mamat

2014-01-01

Deterministic Safety Analysis (DSA) is one of the mandatory requirements conducted for Nuclear Power Plant licensing process, with the aim of ensuring safety compliance with relevant regulatory acceptance criteria. DSA is a technique whereby a set of conservative deterministic rules and requirements are applied for the design and operation of facilities or activities. Computer codes are normally used to assist in performing all required analysis under DSA. To ensure a comprehensive analysis, the conduct of DSA should follow a systematic approach. One of the methodologies proposed is the Standardized and Consolidated Reference Experimental (and Calculated) Database (SCRED) developed by University of Pisa. Based on this methodology, the use of Reference Data Set (RDS) as a pre-requisite reference document for developing input nodalization was proposed. This paper shall describe the application of RDS with the purpose of assessing its effectiveness. Two RDS documents were developed for an Integral Test Facility of LOBI-MOD2 and associated Test A1-83. Data and information from various reports and drawings were referred in preparing the RDS. The results showed that by developing RDS, it has made possible to consolidate all relevant information in one single document. This is beneficial as it enables preservation of information, promotes quality assurance, allows traceability, facilitates continuous improvement, promotes solving of contradictions and finally assisting in developing thermal hydraulic input regardless of whichever code selected. However, some disadvantages were also recognized such as the need for experience in making engineering judgments, language barrier in accessing foreign information and limitation of resources. Some possible improvements are suggested to overcome these challenges

RDS - A systematic approach towards system thermal hydraulics input code development for a comprehensive deterministic safety analysis

Energy Technology Data Exchange (ETDEWEB)

Salim, Mohd Faiz, E-mail: mohdfaizs@tnb.com.my [Nuclear Energy Department, Tenaga Nasional Berhad, Level 32, Dua Sentral, 50470 Kuala Lumpur (Malaysia); Roslan, Ridha [Nuclear Installation Division, Atomic Energy Licensing Board, Batu 24, Jalan Dengkil, 43800 Dengkil, Selangor (Malaysia); Ibrahim, Mohd Rizal Mamat [Technical Support Division, Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

2014-02-12

Deterministic Safety Analysis (DSA) is one of the mandatory requirements conducted for Nuclear Power Plant licensing process, with the aim of ensuring safety compliance with relevant regulatory acceptance criteria. DSA is a technique whereby a set of conservative deterministic rules and requirements are applied for the design and operation of facilities or activities. Computer codes are normally used to assist in performing all required analysis under DSA. To ensure a comprehensive analysis, the conduct of DSA should follow a systematic approach. One of the methodologies proposed is the Standardized and Consolidated Reference Experimental (and Calculated) Database (SCRED) developed by University of Pisa. Based on this methodology, the use of Reference Data Set (RDS) as a pre-requisite reference document for developing input nodalization was proposed. This paper shall describe the application of RDS with the purpose of assessing its effectiveness. Two RDS documents were developed for an Integral Test Facility of LOBI-MOD2 and associated Test A1-83. Data and information from various reports and drawings were referred in preparing the RDS. The results showed that by developing RDS, it has made possible to consolidate all relevant information in one single document. This is beneficial as it enables preservation of information, promotes quality assurance, allows traceability, facilitates continuous improvement, promotes solving of contradictions and finally assisting in developing thermal hydraulic input regardless of whichever code selected. However, some disadvantages were also recognized such as the need for experience in making engineering judgments, language barrier in accessing foreign information and limitation of resources. Some possible improvements are suggested to overcome these challenges.

Statement on safety requirements concerning the long-term operation of the Muehleberg nuclear power station

International Nuclear Information System (INIS)

2012-12-01

This report published by the Swiss Federal Nuclear Safety Inspectorate ENSI investigates the safety requirements with respect to the long-term operation of the Muehleberg nuclear power station in Switzerland. Relevant international requirements and Swiss legal stipulations concerning the long-term operation of the power station are stated. The management of aging processes is looked at. The regular verification of the integrity of various plant components such as containments, piping, steam generation system, etc. is looked at in detail. The state-of-the-art concerning deterministic accident analyses and refitting technology are discussed, as are automated safety systems. The applicable laws, decrees and guidelines are listed in appendices

Staffing requirements for future small and medium reactors (SMRs) based on operating experience and projections