Dynamic compressive response of wrought and additive manufactured 304L stainless steels

Directory of Open Access Journals (Sweden)

Nishida Erik

2015-01-01

Full Text Available Additive manufacturing (AM technology has been developed to fabricate metal components that include complex prototype fabrication, small lot production, precision repair or feature addition, and tooling. However, the mechanical response of the AM materials is a concern to meet requirements for specific applications. Differences between AM materials as compared to wrought materials might be expected, due to possible differences in porosity (voids, grain size, and residual stress levels. When the AM materials are designed for impact applications, the dynamic mechanical properties in both compression and tension need to be fully characterized and understood for reliable designs. In this study, a 304L stainless steel was manufactured with AM technology. For comparison purposes, both the AM and wrought 304L stainless steels were dynamically characterized in compression Kolsky bar techniques. They dynamic compressive stress-strain curves were obtained and the strain rate effects were determined for both the AM and wrought 304L stainless steels. A comprehensive comparison of dynamic compressive response between the AM and wrought 304L stainless steels was performed. SAND2015-0993 C.

Propagation of crevices in stainless steel AISI304L in conditions of hydrogen chemistry (HWC); Propagacion de grietas en acero inoxidable AISI304L en condiciones de quimica de hidrogeno (HWC)

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A.; Fuentes C, P.; Merino C, F. [ININ, 52750 Ocoyoacac, Estado de Mexico (Mexico); Castano M, V. [IFA-UNAM, Juriquilla, Queretaro (Mexico)]. e-mail: ads@nuclear.inin.mx

2006-07-01

Crevice growth velocities in samples of AISI 304L stainless steel thermally welded and sensitized were obtained by the Rising displacement method or of growing displacement. It was used a recirculation circuit in where the operation conditions of a BWR type reactor were simulated (temperature of 288 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu{sup ++} ion. CT pre cracked specimens were used and each rehearsal stayed to one constant displacement velocity of 1 x 10{sup -9} m/s (3.6 {mu}m/hr), making a continuous pursuit of the advance of the crack by the electric potential drop technique. To the end of the rehearsal it was carried out the fractographic analysis of the propagation surfaces. The values of the growth velocities obtained by this methodology went similar to the opposing ones under normal conditions of operation; while the fractographic analysis show the cracks propagation in trans and intergranular ways, evidencing the complexity of the regulator mechanisms of the one IGSCC even under controlled ambient conditions or with mitigation methodologies like the alternative hydrogen chemistry. (Author)

Zirconium oxide deposits (ZrO{sub 2}) and titanium oxide (TiO{sub 2}) on 304l stainless steel; Depositos de oxido de circonio (ZrO{sub 2}) y oxido de titanio (TiO{sub 2}) sobre acero inoxidable 304L

Energy Technology Data Exchange (ETDEWEB)

Davila N, M. L.

2015-07-01

This research project aims to carry out the surface and electrochemical characterization to obtain the optimum conditions of the hydrothermal deposits of zirconium oxide ZrO{sub 2} (baddeleyite) and titanium oxide TiO{sub 2} (anatase and rutile phases) on 304l stainless steel, simulating an inhibiting protective layer. 304l steel specimens were cut, pre-oxidized in water at a temperature of 288 degrees Celsius and 8 MPa, similar to those of a typical BWR conditions. From the titanium oxide anatase crystalline phase, the rutile phase was obtained by a heat treatment at 1000 degrees Celsius. The Sigma-Aldrich pre-oxidized powders and steel 304l were characterized using techniques of X-ray diffraction, scanning electron microscopy, X-ray dispersive energy, chemical mapping and Raman spectrometry. The pre-oxidized steel has two oxide layers, an inner layer with nano metric crystals and another outer of larger crystals to 1μm, with the formation of hematite and magnetite, this predominating. The surface that contacted the sample holder has larger crystals. Hydrothermal deposits were carry out from suspensions of 10, 100 and 1000 ppm, of the crystal phases of anatase, rutile and baddeleyite, on the pre-oxidized steel at a temperature of 150 degrees Celsius for 2 and 7 days, samples were analyzed by X-ray diffraction, scanning electron microscopy, X-ray dispersive energy, Raman spectrometry and Tafel polarization. The suspension to 1000 ppm for 7 days coated surface most; the baddeleyite deposit is noticed more homogeneous than anatase and rutile. The deposit is favored when hematite and magnetite crystals are larger. The chemical mapping on deposits show that even after being immersed in water to 288 degrees Celsius during 30 days, the deposits are still present although a loss is observed. A reference electrode was assembled to conduct electrochemical tests of Tafel able to withstand a temperature of 288 degrees Celsius and pressure of 8 MPa. The baddeleyite deposit

Long-Term Effects of Temperature Exposure on SLM 304L Stainless Steel

Science.gov (United States)

Amine, Tarak; Kriewall, Caitlin S.; Newkirk, Joseph W.

2018-03-01

Austenitic stainless steel is extensively used in industries that operate at elevated temperatures. This work investigates the high-temperature microstructure stability as well as elevated-temperature properties of 304L stainless steel fabricated using the selective laser melting (SLM) process. Significant microstructural changes were seen after a 400°C aging process for as little as 25 h. This dramatic change in microstructure would not be expected based on the ferrite decomposition studied in conventional 304L materials. The as-built additively manufactured alloy has much faster kinetic response to heat treatment at 400°C. An investigation of the structures which occur, the kinetics of the various transformations, and the mechanical properties is presented. The impact of this on the application of SLM 304L is discussed.

L2 Milestone 5433: Characterization of Dynamic Behavior of AM and Conventionally Processed Stainless Steel (316L and 304L)

Energy Technology Data Exchange (ETDEWEB)

Gray, George Thompson [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Livescu, Veronica [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rigg, P. A. [Washington State Univ., Pullman, WA (United States). Inst. for Shock Physics; Trujillo, Carl Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cady, Carl McElhinney [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chen, Shuh-Rong [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carpenter, John S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lienert, Thomas J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fensin, Saryu Jindal [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Knapp, Cameron M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Beal, Roberta Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Morrow, Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dippo, Olivia F. [Univ. of California, San Diego, CA (United States); Jones, David Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Daniel Tito [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Valdez, James Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-26

For additive manufacturing (AM) of metallic materials, the certification and qualification paradigm needs to evolve as there currently exists no broadly accepted “ASTM- or DIN-type” additive manufacturing certified process or AM-material produced specifications. Accordingly, design, manufacture, and thereafter implementation and insertion of AM materials to meet engineering applications requires detailed quantification of the constitutive (strength and damage) properties of these evolving materials, across the spectrum of metallic AM methods, in comparison/contrast to conventionally-manufactured metals and alloys. This report summarizes the 316L SS research results and presents initial results of the follow-on study of 304L SS. For the AM-316L SS investigation, cylindrical samples of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM) equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS was characterized in both the “as-built” Additively Manufactured state and following a heat-treatment designed to obtain full recrystallization to facilitate comparison with annealed wrought 316L SS. The dynamic shock-loading-induced damage evolution and failure response of all three 316L SS materials was quantified using flyer-plate impact driven spallation experiments at peak stresses of 4.5 and 6.35 GPa. The results of these studies are reported in detail in the first section of the report. Publication of the 316L SS results in an archival journal is planned. Following on from the 316L SS completed work, initial results on a study of AM 304L SS are in progress and presented herein. Preliminary results on the structure/dynamic spallation property behavior of AM-304L SS fabricated using both the directed-energy LENS and an EOS powder-bed AM techniques in comparison to wrought 304L SS is detailed in this Level 2 Milestone report.

Cold rolled texture and microstructure in types 304 and 316L austenitic stainless steels

International Nuclear Information System (INIS)

Wasnik, D.N.; Samajdar, I.; Gopalakrishnan, I.K.; Yakhmi, J.V.; Kain, V.

2003-01-01

Two grades of austenitic stainless steel (ASS), types 304 (UNS S 30400) and 316L (UNS S 31603), were cold rolled to different reductions by unidirectional and by cross-rolling. The steels had reasonable difference in stacking fault energy (estimated respectively as 15 and 61 mJ/m 2 in types 304 and 316L) and also in starting (or pre-deformation) crystallographic texture-being relatively weak and reasonably strong in types 304 and 316L respectively. The cold rolling increased texturing in type 304, but not in type 316L ASS. The more significant effect of cold rolled texture development was in the relative increase of Brass ({011} ) against Copper ({112} ) and S ({231} ) orientations. In type 304 the increase in Brass was significant, while in type 316L the increase in Copper and S was stronger. This effect could be captured by Taylor type deformation texture simulations considering stronger twinning contributions in type 304 - for example the respective 'best-fits' (in terms of matching the changes in the volume fractions of Brass against Copper and S) were obtained by full constraint Taylor model with 1:100 and 1:10 slip:twin activities in types 304 and 316L ASS respectively. Microstructural developments during cold rolling were generalized as strain induced martensite formation and developments of dislocation substructure. The former, as estimated by vibrating sample magnetometer (VSM), increased with cold reduction, being significantly more in type 304 and was also noticeably stronger in both grades under cross-rolling. The most significant aspect of substructural developments was the formation of strain localizations. These were observed as dense dislocation walls (DDWs), micro-bands (MBs) and twin lamellar structures (TLS). The TLS contribution gained significance at higher reductions and during cross-rolling, especially in type 304. Large misorientation development and the accompanying grain splittings were always associated with such strain localizations

Intergranular stress corrosion in soldered joints of stainless steel 304.; Corrosion intergranular bajo esfuerzo en uniones soldadas de acero inoxidable 304

Energy Technology Data Exchange (ETDEWEB)

Zamora R, L [Instituto Nacional de Investigaciones Nucleares, Mexico City (Mexico)

1994-12-31

The intergranular stress cracking of welded joints of austenitic stainless steel, AISI 304, is a serious problem in BWR type reactors. It is associated with the simultaneous presence of three factors; stress, a critical media and sensibilization (DOS). EPR technique was used in order to verify the sensibilization degree in the base metal, and the zone affected by heat and welding material. The characterization of material was done. The objective of this work is the study of microstructure and the evaluation of EPR technique used for the determination of DOS in a welded plate of austenitic stainless steel AISI 304. (Author).

Assessment and comparison of oxides grown on 304l ods steel and 304l ss in water environment in supercritical conditions

International Nuclear Information System (INIS)

Mihalache, M.; Dinu, A.; Fulger, M.; Zhou, Z.; Mihalache, M.

2013-01-01

In order to fulfil superior cladding for new reactor generation G IV, the austenitic 3 04 L stainless steel was improved by oxide dispersion strengthening (ODS), using two nano-oxides: titanium and yttrium oxides. The behaviour of the new material resulted, 304 ODS, in water at supercritical temperature of about 550 O C and 25 MPa pressure, was considered. The oxidation kinetics by weigh gain measurements for both materials have been estimated and compared. The weight gain of ODS samples is higher than basic austenitic steel up to 1320 hours. The oxides developed on the ODS samples in SCPW are layered and more uniform than in 304 L SS. The protectively character of oxide films was estimated by different techniques. The morphology of oxide surface, the layering and chemical formula of oxides films were investigated by scanning electron microscopy (SEM), Energy Dispersion X-Ray Spectrometry (EDS), electrochemical impedance spectrometry (EIS) and by Small Angle X-ray Diffraction (SAXD). 1. (authors)

Tensile Stress-Strain Results for 304L and 316L Stainless-Steel Plate at Temperature

International Nuclear Information System (INIS)

R. K. Blandford; D. K. Morton; S. D. Snow; T. E. Rahl

2007-01-01

The Idaho National Laboratory (INL) is conducting moderate strain rate (10 to 200 per second) research on stainless steel materials in support of the Department of Energy's (DOE) National Spent Nuclear Fuel Program (NSNFP). For this research, strain rate effects are characterized by comparison to quasi-static tensile test results. Considerable tensile testing has been conducted resulting in the generation of a large amount of basic material data expressed as engineering and true stress-strain curves. The purpose of this paper is to present the results of quasi-static tensile testing of 304/304L and 316/316L stainless steels in order to add to the existing data pool for these materials and make the data more readily available to other researchers, engineers, and interested parties. Standard tensile testing of round specimens in accordance with ASTM procedure A 370-03a were conducted on 304L and 316L stainless-steel plate materials at temperatures ranging from -20 F to 600 F. Two plate thicknesses, eight material heats, and both base and weld metal were tested. Material yield strength, Young's modulus, ultimate strength, ultimate strain, failure strength and failure strain were determined, engineering and true stress-strain curves to failure were developed, and comparisons to ASME Code minimums were made. The procedures used during testing and the typical results obtained are described in this paper

Martensitic transformation in 304L and 316L types stainless steels cathodically hydrogen charged

International Nuclear Information System (INIS)

Minkovitz, E.; Eliezer, D.

1984-01-01

This paper reports a TEM study on the role of phase transitions at the crack tip in 304L and 316L types stainless steels cathodically hydrogen charged in the absence of any eternally applied forces. The possible role of α prime and epsilon martensite phases in the fracture mechanism is discussed

Characterization of gold and nickel coating on AISI 304 stainless steel for use in the fabrication of current collector plates for fuel cells; Caracterizacion de recubrimientos de oro y niquel realizados sobre acero inoxidable AISI 304 para su empleo en la fabricacion de placas colectoras de corriente para celdas de combustible

Energy Technology Data Exchange (ETDEWEB)

Flores Hernandez, J. Roberto [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)] e-mail: jrflores@iie.org.mx; Aguilar Gama, M. Tulio [UNAM. Facultad de Quimica, Mexico D.F. (Mexico); Cano Castillo, Ulises; Albarran, Lorena [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Olvera, J. Carlos; Orozco, German [CIDETEQ, Pedro Escobedo, Queretaro (Mexico)

2009-09-15

Among the different components that compose fuel cell technology (MEA, bipolar plates, seals, etc.) current collector plates play an important role in the good performance of fuel cells, since they collect all of the current generated and distribute it to the external circuit. Therefore, the most important properties that the current collector plates should have are excellent conductivity and good resistance to the corrosive conditions present in the fuel cell. This document presents results obtained during the nickel and gold electrodeposition process on AISI 304 stainless steel and the morphology and thickness of each coating, their adhesion, hardness and conductivity values. Finally, results obtained during some of the electrochemical tests performed on the coatings are shown. [Spanish] De los diferentes componentes que integran la tecnologia de celdas de combustible (MEA's, placas bipolares, sellos, etc.), las placas colectoras de corriente tienen un importante rol en el buen desempeno de la celdas de combustibles, ya que en estas placas se colecta toda la corriente generada y se distribuye al circuito externo. Debido a esto, las propiedades mas importantes que deben tener las placas colectaras de corriente son: excelente conductividad y buena resistencia a las condiciones corrosivas presentes en la celda de combustible. En este documento se presentan los resultados obtenidos en el proceso de electrodeposicion de niquel y oro sobre acero inoxidable AISI 304, asi como la morfologia y el espesor de cada recubrimiento, sus valores de adherencia, dureza y conductividad. Finalmente se muestran tambien los resultados obtenidos de algunas pruebas electroquimicas a los que fueron sometidos los recubrimientos.

DEFORMACIÓN ELÁSTICA RESIDUAL EN LÁMINAS DE ACERO AISI 304 RECUBIERTAS CON UNA PELÍCULA DE NITRURO DE TITANIO DEPOSITADA POR PVD-MAGNETRON SPUTTERING

Directory of Open Access Journals (Sweden)

H. A. COLORADO

2009-01-01

Full Text Available Se realizó una caracterización mediante difracción de rayos x (DRX en láminas de acero inoxidable AISI 304 recubierto con una capa de nitruro de titanio de 3 um de espesor, obtenida mediante deposición física de vapor (PVD-MAGNETRON SPUTTERING a una temperatura de 200 °C. se tomaron imágenes de microscopía electrónica de barrido (MEB, microscopía óptica (MO y microscopía de fuerza atómica (MFA para caracterizar el sustrato, la capa y la zona cercana a la intercara. adicionalmente se determinó la deformación elástica residual asociada con el ensanchamiento de los picos de DRX.

Passivity and passivity breakdown of 304L stainless steel in hot and concentrated nitric acid

International Nuclear Information System (INIS)

Gillard-Tcharkhtchi, Elsa

2014-01-01

The objective of this study is to characterize the oxidation behavior of 304L stainless steel (SS) in representative conditions of spent nuclear fuel reprocessing, i.e. in hot and concentrated nitric acid. In these conditions the SS electrochemical potential is in the passive domain and its corrosion rate is low. However when the media becomes more aggressive, the potential may be shifted towards the trans-passive domain characterized with a high corrosion rate. Passivity and passivity breakdown in the trans-passive domain are of a major interest for the industry. So as to characterize these phenomenons, this work was undertaken with the following representative conditions: a 304L SS from an industrial sheet was studied, the media was hot and concentrated HNO 3 , long term tests were performed. First, the surface of an immersed 304L SS was characterized with several complementary techniques from the micro to the nanometer scale. Then oxidation kinetics was studied in the passive and in the trans-passive domain. The oxidation behavior was studied thanks to weight loss determination and surface analysis. Finally, oxidation evolution as a function of the potential was studied from the passive to the trans-passive domain. In particular, this allowed us to obtain the anodic curve of 304L SS in hot and concentrated and to define precisely the 304L SS limits of in such conditions. (author) [fr

Preparation of high-performance ultrafine-grained AISI 304L stainless steel under high temperature and pressure

Directory of Open Access Journals (Sweden)

Peng Wang

2016-08-01

Full Text Available Bulk ultra-fine grained (UFG AISI 304L stainless steel with excellent mechanical properties was prepared by a high-temperature and high-pressure (HTHP method using nanocrystalline AISI 304L stainless steel powders obtained from ball milling. Samples were sintered in high-pressure conditions using the highest martensite content of AISI 304L stainless steel powders milled for 25 h. Analyses of phase composition and grain size were accomplished by X-ray diffraction and Rietveld refinement. By comparing the reverse martensite transformation under vacuum and HTHP treat, we consider that pressure can effectively promote the change in the process of transformation. Compared with the solid-solution-treated 304L, the hardness and yield strength of the samples sintered under HTHP are considerably higher. This method of preparation of UFG bulk stainless steel may be widely popularised and used to obtain UFG metallic materials with good comprehensive performance.

Notch Effect on Tensile Deformation Behavior of 304L and 316L Steels in Liquid Helium and Hydrogen

International Nuclear Information System (INIS)

Shibata, K.; Fujii, H.

2004-01-01

Tensile tests of type 304L and 316L steels were carried out using round bar specimens with a notch in liquid helium, hydrogen, liquid nitrogen and at ambient temperature. The obtained tensile strengths were compared with the tensile strengths of smooth specimens. For smooth specimens, tensile strength increased with a decrease in temperature and the strengths in liquid helium and hydrogen show similar values in both steels. For notched specimen of 304L steel, tensile strength (including fracture strength) increased noticeably from ambient to liquid nitrogen temperature but showed a large decrease in liquid helium and hydrogen. In liquid hydrogen and helium, the tensile strength is a little lower in liquid hydrogen than in liquid helium and both strengths are lower than tensile strengths of smooth specimens. For notched specimen of 316L steel, an increase in tensile strength from ambient to liquid nitrogen temperature was not so large and a decrease from liquid nitrogen to liquid hydrogen was small. The tensile strengths in liquid helium and hydrogen were nearly same and higher than those of smooth specimens. Different behavior of serration was observed between liquid helium and hydrogen, and between 304L and 316L steels. The reasons for these differences were discussed using computer simulation

Microstructure and mechanical properties of 304L steel fabricated by arc additive manufacturing

Directory of Open Access Journals (Sweden)

Ji Lei

2017-01-01

Full Text Available For 304L large structural parts used in nuclear power, it is hard and costly to fabricate and machine traditionally. Wire arc additive manufacturing (WAAM has low cost and high material utilization, which provides an efficient way to fabricate the large structural parts. So in this study, WAAM is used to fabricate the parts of 304L stainless steel. Through the tensile test and metallographic analysis, the mechanical properties and microstructure of the 304L stainless steel fabricated by WAAM were explored. The results indicate that with the layers depositing, the cooling rate becomes slower, the dendrites become thicker and the morphology becomes more stable. Due to the existence of dendrites, the grain boundary strengthening effect is different between the transverse direction and longitudinal direction, and resulting in anisotropy of mechanical properties. However, the mechanical properties of the parts correspond to the forged piece, which lays the foundation for future applications.

Simulación del efecto de la irradiación mediante el trabajado en frío y los tratamientos térmicos en dos aceros inoxidables austeníticos

Directory of Open Access Journals (Sweden)

de Diego, G.

1998-10-01

Full Text Available In the present study, annealed type 304 SS was cold worked and heat treated to simúlate irradiation hardening, ductility loss and grain boundary segregation. Constant Extension Rate Tensile (CERT tests were conducted to reproduce Irradiation Assisted Stress Corrosion Cracking (IASCC in BWR (Boiling Water Reactor environment.

En este trabajo se simulan los efectos que produce la irradiación, pérdida de ductilidad y segregación de impurezas en borde de grano, mediante trabajado en frío y posterior tratamiento térmico, para aceros inoxidables austeníticos AISI 304. Mediante ensayos de velocidad de extensión constante y en medios similares a los de los reactores de agua en ebullición se intenta relacionar la susceptibilidad a la corrosión bajo tensión con la susceptibilidad a la corrosión asistida por irradiación.

Irradiation-induced creep in 316 and 304L stainless steels

International Nuclear Information System (INIS)

Walters, L.C.; McVay, G.L.; Hudman, G.D.

1977-01-01

Recent results are presented from the in-reactor creep experiments that are being conducted by Argonne National Laboratory. The experiments consist of four subassemblies that contain helium-pressurized as well as unstressed capsules of 316 and 304L stainless steels in several metallurgical conditions. Experiments are being irradiated in row 7 of the EBR-II sodium-cooled fast breeder reactor. Three of the subassemblies are being irradiated at temperatures near 400 0 C, and the fourth subassembly is being irradiated at a temperature of 550 0 C. Creep and swelling strains were determined by profilometer measurements on the full length of the capsules after each irradiation cycle. The accumulated neutron dose on the 304L capsules at 385 0 C was 45 dpa; on the 316 capsules at 400 0 C, 40 dpa; and on the 316 capsules at 550 0 C, 25 dpa. It was found that the in-reactor creep rates were linearly dependent on hoop stress, with the exception being capsules of 316 stainless steel that had been given long-term carbide aging treatment and then irradiated at 550 0 C. Those capsules exhibited much higher creep and swelling rates than their unaged counterparts. For the metallurgical conditions where significant swelling was observed (solution-annealed 304L and aged 316 stainless steels), it was found that the in-reactor creep rates were readily fit to a model that related the creep rates to accumulated swelling. Additionally, it was found that the stress-normalized creep rate for 20%-cold-worked 316 stainless steel at a temperature of 550 0 C was 1.6 times that observed at 400 0 C

Multitechnique characterisation of 304L surface states oxidised at high temperature in steam and air atmospheres

Energy Technology Data Exchange (ETDEWEB)

Mamede, Anne-Sophie, E-mail: anne-sophie.mamede@ensc-lille.fr [University Lille, CNRS, ENSCL, Centrale Lille, University Artois, UMR 8181 – UCCS – Unité de Catalyse et Chimie du Solide, F-59000 Lille (France); Nuns, Nicolas, E-mail: nicolas.nuns@univ-lille1.fr [University Lille, CNRS, ENSCL, Centrale Lille, University Artois, UMR 8181 – UCCS – Unité de Catalyse et Chimie du Solide, F-59000 Lille (France); Cristol, Anne-Lise, E-mail: anne-lise.cristol@ec-lille.fr [University Lille, CNRS, Centrale Lille, Arts et Métiers Paris Tech, FRE 3723 – LML – Laboratoire de Mécanique de Lille, F-59000 Lille (France); Cantrel, Laurent, E-mail: laurent.cantrel@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES, Cadarache, Saint Paul lez Durance, 13115 (France); Laboratoire de Recherche Commun IRSN-CNRS-Lille 1: «Cinétique Chimique, Combustion, Réactivité» (C3R), Cadarache, Saint Paul lez Durance, 13115 (France); Souvi, Sidi, E-mail: sidi.souvi@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES, Cadarache, Saint Paul lez Durance, 13115 (France); Laboratoire de Recherche Commun IRSN-CNRS-Lille 1: «Cinétique Chimique, Combustion, Réactivité» (C3R), Cadarache, Saint Paul lez Durance, 13115 (France); and others

2016-04-30

Graphical abstract: - Highlights: • Mutitechnique characterisation of oxidised 304L. • Oxidation at high temperature under steam and air conditions of 304L stainless steel. • Chromium and manganese oxides formed in the outer layer. • Oxide profiles differ in air or steam atmosphere. - Abstract: In case of a severe accident occurring in a nuclear reactor, surfaces of the reactor coolant system (RCS), made of stainless steel (304L) rich in Cr (>10%) and Ni (8–12%), are oxidised. Fission products (FPs) are released from melt fuel and flow through the RCS. A part of them is deposited onto surfaces either by vapour condensation or by aerosol deposition mechanisms. To be able to understand the nature of interactions between these FPs and the RCS surfaces, a preliminary step is to characterize the RSC surface states in steam and air atmosphere at high temperatures. Pieces of 304L stainless steel have been treated in a flow reactor at two different temperatures (750 °C and 950 °C) for two different exposition times (24 h and 72 h). After surfaces analysing by a unique combination of surface analysis techniques (XPS, ToF-SIMS and LEIS), for 304L, the results show a deep oxide scale with multi layers and the outer layer is composed of chromium and manganese oxides. Oxide profiles differ in air or steam atmosphere. Fe{sub 2}O{sub 3} oxide is observed but in minor proportion and in all cases no nickel is detected near the surface. Results obtained are discussed and compared with the literature data.

Influencia de la soldadura sobre la rotura por tensiones en tubos de acero inoxidable austenitico del tipo 18-11NB(TP347

Directory of Open Access Journals (Sweden)

Gutiérrez de Saiz-Solabarria, S.

2000-06-01

Full Text Available This work has been undertaken to study the stress cracking failure in various 18Cr11Ni [TP347 (18-11Nb, TP 321 (18-11 Ti, TP304 (18-11 and TP316 (18-11-2] types austenitic stainless steel tubes. The material used was produced hot-rolling at 76,2 mm φ (3"φ x 2,54 mm (1/10" thickness. The study was carried out at 593ºC and applied stress of 50 Ton/in2.

Se estudia el efecto de la soldadura sobre la rotura por tensiones en tubos de acero inoxidable austenítico estabilizado con Nb o Ti de los tipos 18-11Nb (TP 347 y 18-11Ti (TP 321 así como sin estabilizar del tipo 18-11 (TP 304 y con Mo del tipo 18-11-2 (TP 316. Los tubos, en todos los casos, son de dimensiones 76,2 mm (3” φ x 2,54 mm (1/10” de espesor y la tensión aplicada (σ de 10 Ton/in2, para una temperatura de servicio de 593ºC.

Effect of Temperature on the Fracture Toughness of Hot Isostatically Pressed 304L Stainless Steel

OpenAIRE

Cooper, Adam J.; Sherry, Andrew

2018-01-01

Herein, we have performed J-Resistance multi-specimen fracture toughness testing of hot isostatically pressed (HIP’d) and forged 304L austenitic stainless steel, tested at elevated (300 °C) and cryogenic (− 140 °C) temperatures. The work highlights that although both materials fail in a pure ductile fashion, stainless steel manufactured by HIP displays a marked reduction in fracture toughness, defined using J0.2BL, when compared to equivalently graded forged 304L, which is relatively constant...

Weld solidification cracking in 304 to 304L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Hochanadel, Patrick W [Los Alamos National Laboratory; Lienert, Thomas J [Los Alamos National Laboratory; Martinez, Jesse N [Los Alamos National Laboratory; Martinez, Raymond J [Los Alamos National Laboratory; Johnson, Matthew Q [Los Alamos National Laboratory

2010-01-01

A series of annulus welds were made between 304 and 304L stainless steel coaxial tubes using both pulsed laser beam welding (LBW) and pulsed gas tungsten arc welding (GTAW). In this application, a change in process from pulsed LBW to pulsed gas tungsten arc welding was proposed to limit the possibility of weld solidification cracking since weldability diagrams developed for GTAW display a greater range of compositions that are not crack susceptible relative to those developed for pulsed LBW. Contrary to the predictions of the GTAW weldability diagram, cracking was found. This result was rationalized in terms of the more rapid solidification rate of the pulsed gas tungsten arc welds. In addition, for the pulsed LBW conditions, the material compositions were predicted to be, by themselves, 'weldable' according to the pulsed LBW weldability diagram. However, the composition range along the tie line connecting the two compositions passed through the crack susceptible range. Microstructurally, the primary solidification mode (PSM) of the material processed with higher power LBW was determined to be austenite (A), while solidification mode of the materials processed with lower power LBW apparently exhibited a dual PSM of both austenite (A) and ferrite-austenite (FA) within the same weld. The materials processed by pulsed GT A W showed mostly primary austenite solidification, with some regions of either primary austenite-second phase ferrite (AF) solidification or primary ferrite-second phase austenite (FA) solidification. This work demonstrates that variations in crack susceptibility may be realized when welding different heats of 'weldable' materials together, and that slight variations in processing can also contribute to crack susceptibility.

Evaluation of Mechanical Properties and Fatigue Behavior of STS 304L due to Plastic Working

Energy Technology Data Exchange (ETDEWEB)

Shim, Hyun-Bo [Yeungnam Univ., Daegu (Korea, Republic of); Kim, Young-Kyun [KOGAS Research Institute, Seoul (Korea, Republic of); Suh, Chang-Min [Kyungpook Nat’l Univ., Daegu (Korea, Republic of)

2017-07-15

The purpose of this study is to investigate the influence of the cold reduction rate and an ultrasonic fatigue test (UFT) on the fatigue behaviors of STS 304L. The tensile strength, yield strength, hardness value and fatigue limit in the UFT fatigue test linearly increased as thickness decreased from 1.5 mm to 1.1 mm, as the cold reduction rate of STS 304L increased. As a result of the UFT fatigue test (R = -1) of four specimens, the fatigue limit of the S-N curve formed a knee point in the region of 10{sup 6}, and the 2nd fatigue limit caused by giga cycle fatigue did not appeared. In the case of t = 1.1 mm, the highest fatigue limit was 345 MPa, which was 64.3% higher than the original material (t = 1.5 mm). As a result of the UFT fatigue test of STS 304L, many small surface cracks occurred, grown, coalesced while tearing.

Effect of Temperature on the Fracture Toughness of Hot Isostatically Pressed 304L Stainless Steel

Science.gov (United States)

Cooper, A. J.; Brayshaw, W. J.; Sherry, A. H.

2018-03-01

Herein, we have performed J- Resistance multi-specimen fracture toughness testing of hot isostatically pressed (HIP'd) and forged 304L austenitic stainless steel, tested at elevated (300 °C) and cryogenic (- 140 °C) temperatures. The work highlights that although both materials fail in a pure ductile fashion, stainless steel manufactured by HIP displays a marked reduction in fracture toughness, defined using J 0.2BL, when compared to equivalently graded forged 304L, which is relatively constant across the tested temperature range.

Effect of Prior Deformation on Welding Microstructure of Steel 304L

Directory of Open Access Journals (Sweden)

WU Luo-fei

2017-01-01

Full Text Available This subject was raised by an automotive company.Based on the welding design on the curved surface,the effect of prior deformation on the weld structure was studied.Metal active-gas welding was used on the T-joint and pre-deformed plates of austenitic stainless steel 304L to find the proper welding parameters and observe the effect of prior deformation on the microstructure.The proper parameters acquired are:the speed of the torch is 4mm/s,the speed of delivery of welding wire is 2.5m/min and the voltage is 17V.In the T-joint and pre-deformed joint,the weld toes are in the zone with strain of 0% and 30%.In the pre-deformed welding specimen,it was observed that the fusion zone and partially melted zone are narrowed,carbide precipitation and ferrites are found less.In all,the microstructure in the pre-deformed weld joints on 304L is more uniform.

An Assessment of the Ductile Fracture Behavior of Hot Isostatically Pressed and Forged 304L Stainless Steel

Science.gov (United States)

Cooper, A. J.; Smith, R. J.; Sherry, A. H.

2017-05-01

Type 300 austenitic stainless steel manufactured by hot isostatic pressing (HIP) has recently been shown to exhibit subtly different fracture behavior from that of equivalent graded forged steel, whereby the oxygen remaining in the component after HIP manifests itself in the austenite matrix as nonmetallic oxide inclusions. These inclusions facilitate fracture by acting as nucleation sites for the initiation, growth, and coalescence of microvoids in the plastically deforming austenite matrix. Here, we perform analyses based on the Rice-Tracey (RT) void growth model, supported by instrumented Charpy and J-integral fracture toughness testing at ambient temperature, to characterize the degree of void growth ahead of both a V-notch and crack in 304L stainless steel. We show that the hot isostatically pressed (HIP'd) 304L steel exhibits a lower critical void growth at the onset of fracture than that observed in forged 304L steel, which ultimately results in HIP'd steel exhibiting lower fracture toughness at initiation and impact toughness. Although the reduction in toughness of HIP'd steel is not detrimental to its use, due to the steel's sufficiently high toughness, the study does indicate that HIP'd and forged 304L steel behave as subtly different materials at a microstructural level with respect to their fracture behavior.

Teste de tuberculinização em caprinos (Capra hircus experimentalmente sensibilizados Tuberculin test in experimentally sensitized goats (Capra hircus

Directory of Open Access Journals (Sweden)

Paulo Eduardo Gomes da Silva

2006-06-01

Full Text Available Foram estabelecidos critérios de interpretação do teste de tuberculinização aplicado ao diagnóstico da tuberculose em grupos de caprinos experimentalmente sensibilizados. Dos 30 animais utilizados, dez foram sensibilizados com Mycobacterium avium - amostra D4 (grupo A e dez com Mycobacterium bovis - amostra AN5 (grupo B. Dez caprinos não foram sensibilizados e constituíram o grupo controle (grupo C. No teste cervical simples, realizado com tuberculina bovina (M. bovis e lido às 72 horas pós-tuberculinização (p.t., as reações positivas foram aquelas em que houve aumento da espessura da dobra de pele igual ou superior a 3,9mm; reações inconclusivas, quando situadas entre 1,8 e 3,8mm, e negativas quando iguais ou menores que 1,7mm. A análise dos resultados do teste cervical comparativo, realizado com o M. avium e M. bovis e lido às 72 horas p.t., indicou reação positiva quando o aumento da espessura da dobra da pele induzida pela tuberculina bovina superou a reação à aviária em pelo menos 2,5mm; reação inconclusiva quando a diferença entre a reação à tuberculina bovina e à tuberculina aviária ficou situada entre 1,9 e 2,4mm; e negativa quando a reação bovina ultrapassou a aviária em até 1,8mm. Às 96 horas após a injeção da tuberculina, foi efetuada a avaliação histológica do local das reações tuberculínicas colhendo-se amostras de pele de cinco caprinos dos grupos A e B e de quatro animais do grupo controle; os resultados confirmaram a presença, nos grupos sensibilizados, de infiltrado inflamatório, constituído, preferencialmente, por células mononucleares.The tuberculin skin test was established with the aim to be applied in the diagnosis of tuberculosis in experimentally sensitized goats. Thirty goats were alocated into three groups with ten animals each. The animals in group A were sensitized with Mycobacterium avium sample D4; group B with Mycobacterium bovis sample AN5; and group C (control was

Intergranular stress corrosion cracking of ion irradiated 304L stainless steel in PWR environment

International Nuclear Information System (INIS)

Gupta, Jyoti

2016-01-01

IASCC is irradiation - assisted enhancement of intergranular stress corrosion cracking susceptibility of austenitic stainless steel. It is a complex degrading phenomenon which can have a significant influence on maintenance time and cost of PWRs' core internals and hence, is an issue of concern. Recent studies have proposed using ion irradiation (to be specific, proton irradiation) as an alternative of neutron irradiation to improve the current understanding of the mechanism. The objective of this study was to investigate the cracking susceptibility of irradiated SA 304L and factors contributing to cracking, using two different ion irradiations; iron and proton irradiations. Both resulted in generation of point defects in the microstructure and thereby causing hardening of the SA 304L. Material (unirradiated and iron irradiated) showed no susceptibility to intergranular cracking on subjection to SSRT with a strain rate of 5 * 10 -8 s -1 up to 4 % plastic strain in inert environment. But, irradiation (iron and proton) was found to increase intergranular cracking severity of material on subjection to SSRT in simulated PWR primary water environment at 340 C. Correlation between the cracking susceptibility and degree of localization was studied. Impact of iron irradiation on bulk oxidation of SA 304L was studied as well by conducting an oxidation test for 360 h in simulated PWR environment at 340 C. The findings of this study indicate that the intergranular cracking of 304L stainless steel in PWR environment can be studied using Fe irradiation despite its small penetration depth in material. Furthermore, it has been shown that the cracking was similar in both iron and proton irradiated samples despite different degrees of localization. Lastly, on establishing iron irradiation as a successful tool, it was used to study the impact of surface finish and strain paths on intergranular cracking susceptibility of the material. (author) [fr

Corrosion behavior of powder metallurgical stainless steels in urban and marine environments

Directory of Open Access Journals (Sweden)

Bautista, A.

2006-06-01

Full Text Available This work studies the development of corrosive attack on sintered components manufactured from AISI 316L and AISI 304L powders. The stainless steels were sintered in vacuum and in nitrogen-base atmosphere at 1,120 and 1,250 ºC, and their corrosion resistance was then analyzed by electrochemical techniques and by atmospheric corrosion testing (two years at urban and marine test sites. Images are shown of the morphology of the attack on the surface of the stainless steels and the development of this attack in the interior of the material.

Este trabajo estudia el desarrollo del proceso corrosivo en componentes sinterizados fabricados a partir de polvos de AISI 316L y AISI 304L. Los aceros inoxidables fueron sinterizados en vacío y en atmósfera base nitrógeno a 1.120 y 1.250 ºC y, su resistencia a corrosión se ha analizado mediante técnicas electroquímicas y mediante ensayos de corrosión atmosférica (dos años en ambientes urbano y marino. Se muestran imágenes de la morfología del ataque en la superficie de los aceros inoxidables y del desarrollo de este ataque en el interior del material.

Desarrollo de los procesos de moldeo por inyección y extrusión de polvos para la obtención de piezas de aceros inoxidables dúplex y ferríticos

OpenAIRE

Sotomayor Lozano, María Eugenia

2011-01-01

En la presente Tesis Doctoral se ha desarrollado el proceso de moldeo por inyección de polvos (pIM) para la obtención de piezas de acero inoxidable dúplex con aplicaciones en ortodoncia. Por otro lado, se ha desarrollado el proceso de moldeo por extrusión de polvos (PEM) para la obtención de láminas y tubos porosos de acero inoxidable ferrítico con aplicaciones en pilas de combustible de óxido sólido (SOFCs). En primer lugar, se prepararon y caracterizaron térmica y reológicamente las mezclas...

Acoustic emission from hydrogen saturated Type 304L stainless steel

International Nuclear Information System (INIS)

Caskey, G.R. Jr.

1978-01-01

Acoustic emission is attributed to energy release within a material body by localized plastic deformation or failure processes. The elastic stress waves may come from slip band formation, mechanical twinning, martensite transformation, or crack propagation. Each of these processes has slightly different acoustic characteristics allowing for easy identification. Acoustic emission was monitored during tensile tests of Type 304L austenitic stainless steel to explore the applicability of the technique to hydrogen-assisted fracture

Characterization of welding of AISI 304l stainless steel similar to the core encircling of a BWR reactor; Caracterizacion de soldaduras de acero inoxidable AISI 304L similares a las de la envolvente del nucleo de un reactor BWR

Energy Technology Data Exchange (ETDEWEB)

Gachuz M, M.E.; Palacios P, F.; Robles P, E.F. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2003-07-01

Plates of austenitic stainless steel AISI 304l of 0.0381 m thickness were welded by means of the SMAW process according to that recommended in the Section 9 of the ASME Code, so that it was reproduced the welding process used to assemble the encircling of the core of a BWR/5 reactor similar to that of the Laguna Verde Nucleo electric plant, there being generated the necessary documentation for the qualification of the one welding procedure and of the welder. They were characterized so much the one base metal, as the welding cord by means of metallographic techniques, scanning electron microscopy, X-ray diffraction, mechanical essays and fracture mechanics. From the obtained results it highlights the presence of an area affected by the heat of up to 1.5 mm of wide and a value of fracture tenacity (J{sub IC}) to ambient temperature for the base metal of 528 KJ/m{sup 2}, which is diminished by the presence of the welding and by the increment in the temperature of the one essay. Also it was carried out an fractographic analysis of the fracture zone generated by the tenacity essays, what evidence a ductile fracture. The experimental values of resistance and tenacity are important for the study of the structural integrity of the encircling one of the core. (Author)

Forging evaluaion of 304L stainless steel

International Nuclear Information System (INIS)

Packard, C.L.; Edstrom, C.M.

1979-01-01

The objective of this project was to evaluate and characterize the effects of various forging parameters on the metallographic structure and mechanical properties of 304L stainless steel forgings. Upset and die forgings were produced by hammer and Dynapak forging with forging temperatures ranging from 760 to 1145 0 C, upset reductions ranging from 20 to 60%, and annealing times ranging from 0 to 25 minutes at 843 0 C. The carbide precipitation behavior observed was found to be a function of forging temperature and annealing time. Higher forging temperatures were beneficial in avoiding continuous carbide precipitation and annealing at 843 0 C promoted increased carbide precipitation. The yield strength of the unannealed forgings decreased with increasing forging temperature and, with the exception of the 1145 0 C upset forgings, was significantly lowered by annealing

The effect of cysteine on the corrosion of 304L stainless steel in sulphuric acid

International Nuclear Information System (INIS)

Silva, A.B.; Agostinho, S.M.L.; Barcia, O.E.; Cordeiro, G.G.O.; D'Elia, E.

2006-01-01

The effect of cysteine on the corrosion of 304L stainless steel in 1 mol l -1 H 2 SO 4 was studied using open-circuit potential measurements, anodic polarization curves, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM). All the electrochemical measurements obtained in the presence of low cysteine concentration (10 -6 -10 -5 mol l -1 ) presented the same behaviour as those obtained in the absence of cysteine, a passivated steel surface. However, for higher cysteine concentrations (10 -4 -10 -2 mol l -1 ), a different behaviour was observed: the corrosion potential stabilized at a more negative value; an active region was observed in the anodic polarization curves and the electrochemical impedance diagrams showed an inductive loop at lower frequencies and a much lower polarization resistance. These results show that the presence of cysteine at high concentration turns the surface of 304L stainless steel electrochemically active, probably dissolving the passivation layer and promoting the stainless steel anodic dissolution. SEM experiments performed after immersion experiments at corrosion potential were in good agreement with the electrochemical results

Oxidation behavior of 304 stainless steel exposed to steam at high temperature

Energy Technology Data Exchange (ETDEWEB)

Jeong, H.; Ryu, J. R.; Park, G. H. [Kyunghee Univ., Yongin (Korea, Republic of); Yoo, T. G. [FNC Technology, Seoul (Korea, Republic of)

2003-10-01

An experiment was conducted on 304 stainless steel(SUS304L) at the LOCA(Lost of Coolant Accident) requirement temperature, 800 .deg. C to 1100 deg. C. SUS304L was used as clothing material and structural frame of LWR. Oxidation behavior of SUS304L by temperature and time was examined after the mechanical and chemical polishing of SUS304L plate. After oxidation, change in weight showed a linear pattern for the first 20 minutes and a parabolic pattern afterwards. Then, fine structure and oxidation layer of SUS304L plate were observed through OM photographing and oxidation characteristics of SUS304L were found through hardness measurement by depth of each plate and XRD(X-Ray Diffraction) photographing.

Effect of welding process, type of electrode and electrode core diameter on the tensile property of 304L austenitic stainless steel

Directory of Open Access Journals (Sweden)

Akinlabi OYETUNJI

2014-11-01

Full Text Available The effect of welding process, type of electrode and electrode core diameter on the tensile property of AISI 304L Austenitic Stainless Steel (ASS was studied. The tensile strength property of ASS welded samples was evaluated. Prepared samples of the ASS were welded under these three various variables. Tensile test was then carried out on the welded samples. It was found that the reduction in ultimate tensile strength (UTS of the butt joint samples increases with increase in core diameter of the electrode. Also, the best electrode for welding 304L ASS is 308L stainless steel-core electrode of 3.2 mm core diameter. It is recommended that the findings of this work can be applied in the chemical, food and oil industries where 304L ASS are predominantly used.

Standard test method for electrochemical reactivation (EPR) for detecting sensitization of AISI type 304 and 304L stainless steels

CERN Document Server

American Society for Testing and Materials. Philadelphia

1994-01-01

1.1 This test method covers a laboratory procedure for conducting an electrochemical reactivation (EPR) test on AISI Type 304 and 304L (UNS No. S30400 and S30403, respectively) stainless steels. This test method can provide a nondestructive means of quantifying the degree of sensitization in these steels (1, 2, 3). This test method has found wide acceptance in studies of the effects of sensitization on intergranular corrosion and intergranular stress corrosion cracking behavior (see Terminology G15). The EPR technique has been successfully used to evaluate other stainless steels and nickel base alloys (4), but the test conditions and evaluation criteria used were modified in each case from those cited in this test method. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this...

Soldadura de recargue con aceros inoxidables dúplex

OpenAIRE

Zappa, Sebastián; Martínez, Juan; Svoboda, Hernán Gabriel; Surian, Estela

2016-01-01

Los aceros inoxidables dúplex se caracterizan por poseer una estructura dual constituida por ferrita y austenita en iguales proporciones. Poseen una combinación de buenas propiedades mecánicas y resistencia a la corrosión, que dependen de la composición química y de la relación entre las fases mencionadas. Son ampliamente utilizados en las industrias de procesos químicos y, fundamentalmente, del petróleo y gas. La soldadura de recargue, es utilizada en las industrias de fabricación y reparaci...

Evaluación del grado de sensibilización en el acero inoxidable AISI

Directory of Open Access Journals (Sweden)

González, O.

2003-12-01

Full Text Available Austenitic stainless steel, when heat-treated at 550-850 °C, became susceptible to intergranular corrosion in acids. This phenomenon, know as sensitization, it is result from the precipitation of chrome carbides in the grain boundary, making these areas less resistant to corrosion. Two different electrochemical reactivation tests are compared with a destructive test and related to the classification of its respective microstructures. It was established a quantitative methodology to evaluate the degree of sensitization in AISI 304 and also to compare the correspondence of the results with the data of the automatic and portable EPR device for non-destructive field measurement of the degree of sensitization. The used electrochemical techniques were the EPR (Electrochemical Potentiokinetic Reactivation or single loop test and the PRP (Pasivation Reactivation Potentiokinetic or double loop test. The destructive test used was boiling, 120 h ferric sulfate-50 % sulfuric acid, according to the standard practices ASTM A-262 practices B. The classifications of each structures were according to the standard practices ASTM A-262 practices B.

El acero inoxidable austenítico, cuando se calienta en un rango de temperatura entre 550 y 850 °C es susceptible a corrosión intergranular en ácidos. Este fenómeno, conocido como sensibilización, es resultado de la precipitación de carburos de cromo en el límite de grano, haciendo esas áreas menos resistentes a la corrosión. Se comparan dos pruebas diferentes de reactivación electroquímica con una prueba destructiva, relacionándolas con su respectiva microestructura. Se estableció una metodología cuantitativa para evaluar el grado de sensibilización del acero AISI 304 y se comparó con los datos generados de una herramienta no destructiva de campo, automática y portátil, para medir el grado de sensibilización. Las técnicas electroquímicas usadas fueron: la EPR (Reactivación electroqu

Corrosion and microstructural aspects of dissimilar joints of titanium and type 304L stainless steel

International Nuclear Information System (INIS)

Mudali, U. Kamachi.; Ananda Rao, B.M.; Shanmugam, K.; Natarajan, R.; Raj, Baldev

2003-01-01

To link titanium and zirconium metal based (Ti, Zr-2, Ti-5%Ta, Ti-5%Ta-1.8Nb) dissolver vessels containing highly radioactive and concentrated corrosive nitric acid solution to other nuclear fuel reprocessing plant components made of AISI type 304L stainless steel (SS), high integrity and corrosion resistant dissimilar joints between them are necessary. Fusion welding processes produce secondary precipitates which dissolve in nitric acid, and hence solid-state processes are proposed. In this work, various dissimilar joining processes available for producing titanium-304L SS joints with adequate strength, ductility and corrosion resistance for this critical application are highlighted. Developmental efforts made at IGCAR, Kalpakkam are outlined. The possible methods and the microstructural-metallurgical properties of the joints along with corrosion results obtained with three phase (liquid, vapour, condensate) corrosion testing are discussed. Based on the results, dissimilar joint produced by the explosive joining process was adopted for plant application

Behaviour under fatigue of AISI 304-L stainless steel welded joints

International Nuclear Information System (INIS)

Scal, M.W.; Joia, C.J.B.M.; Sousa e Silva, A.S. de

1979-01-01

The fatigue behaviour at room temperature of AISI-304-L stainless steel welded joints obtained by two distinct welding methods was studied. The results obtained were compared to those characteristic of the base metal. The welded joint fatigue samples were rectified in order to eliminate the effect of the welded seam geometry. It was concluded that the mechanisms of fatigue crack start in this case is commanded by the austenitic matrix, there being no influence of the delta ferrite rate and distribution present at the melted zone. (Author) [pt

Distinguishing effect of buffing vs. grinding, milling and turning operations on the chloride induced SCC susceptibility of 304L austenitic stainless steel

International Nuclear Information System (INIS)

Kumar, Pandu Sunil; Acharyya, Swati Ghosh; Rao, S.V. Ramana; Kapoor, Komal

2017-01-01

The study compares the effect of different surface working operations like grinding, milling, turning and buffing on the Cl – induced stress corrosion cracking (SCC) susceptibility of austenitic 304L stainless steel (SS) in a chloride environment. SS 304L was subjected to four different surface working operations namely grinding, milling, turning and buffing. The residual stress distribution of the surface as a result of machining was measured by X-ray diffraction. The Cl – induced SCC susceptibility of the different surface worked samples were determined by testing in boiling magnesium chloride as per ASTM G36 for 3 h, 9 h and 72 h. The surface and cross section of the samples both pre and post exposure to the corrosive medium was characterized using optical microscopy, scanning electron microscopy (SEM). The study revealed that grinding, milling and turning operations resulted in high tensile residual stresses on the surface together with the high density of deformation bands making these surfaces highly susceptible to Cl – induced SCC. On the other hand buffing produces compressive residual stresses on the surface with minimal plastic strain, making it more resistance to Cl – induced SCC. The study highlights that the conventional machining operations on 304L SS surfaces should be invariably followed by buffing operation to make the surfaces more resistance to SCC. - Highlights: • Grinding, milling and turning lead to tensile residual stresses and plastic strain. • Buffing leads to compressive residual stresses on the surface and minimal strain. • Grinding, milling and turning make 304L SS surface susceptible to SCC. • Buffed 304L SS surface is immune to SCC. • Grinding, milling, and turning operations should be followed by buffing operation.

Distinguishing effect of buffing vs. grinding, milling and turning operations on the chloride induced SCC susceptibility of 304L austenitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Kumar, Pandu Sunil [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); Acharyya, Swati Ghosh, E-mail: swati364@gmail.com [School of Engineering Sciences and Technology, University of Hyderabad, Hyderabad 500046 (India); Rao, S.V. Ramana; Kapoor, Komal [Nuclear Fuel Complex, Department of Atomic Energy, Government of India, Hyderabad 500062 (India)

2017-02-27

The study compares the effect of different surface working operations like grinding, milling, turning and buffing on the Cl{sup –} induced stress corrosion cracking (SCC) susceptibility of austenitic 304L stainless steel (SS) in a chloride environment. SS 304L was subjected to four different surface working operations namely grinding, milling, turning and buffing. The residual stress distribution of the surface as a result of machining was measured by X-ray diffraction. The Cl{sup –} induced SCC susceptibility of the different surface worked samples were determined by testing in boiling magnesium chloride as per ASTM G36 for 3 h, 9 h and 72 h. The surface and cross section of the samples both pre and post exposure to the corrosive medium was characterized using optical microscopy, scanning electron microscopy (SEM). The study revealed that grinding, milling and turning operations resulted in high tensile residual stresses on the surface together with the high density of deformation bands making these surfaces highly susceptible to Cl{sup –} induced SCC. On the other hand buffing produces compressive residual stresses on the surface with minimal plastic strain, making it more resistance to Cl{sup –} induced SCC. The study highlights that the conventional machining operations on 304L SS surfaces should be invariably followed by buffing operation to make the surfaces more resistance to SCC. - Highlights: • Grinding, milling and turning lead to tensile residual stresses and plastic strain. • Buffing leads to compressive residual stresses on the surface and minimal strain. • Grinding, milling and turning make 304L SS surface susceptible to SCC. • Buffed 304L SS surface is immune to SCC. • Grinding, milling, and turning operations should be followed by buffing operation.

Behavior to the fracture of an AISI 304 stainless steel sensitized in BWR reactor conditions (288 degrees Centigrade and 80 Kg/cm{sup 2}); Comportamiento a la fractura de un acero inoxidable AISI 304 sensibilizado en condiciones de reactor BWR (288 grados Centigrados y 80 Kg/cm{sup 2})

Energy Technology Data Exchange (ETDEWEB)

Hernandez C, R.; Diaz S, A.; Garcia R, R.; Aguilar T, A.; Gachuz M, M.; Arganis J, C.; Merino C, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

1999-07-01

It is a knew fact that ductility of a lot of structural alloys can be deteriorated by the environment effect which are exposed, and that their consequent embrittlement can put in doubt the safety of their functioning; such is the case of austenitic stainless steels used in internal components of the BWR type reactors which not only is subjected to the effect combined of the aggressive environment which surround it (pressure, temperature, corrosion potential, conductivity medium, local state of efforts, etc.), but also to the action of present neutron radiation, manifesting microstructural changes which are reflected in the augmentation of its susceptibility to the intergranular cracking, phenomena generally known as IASCC ''Irradiation Assisted Stress Corrosion Cracking''. Once appeared the cracking in the material, the useful life of a component is limited by the rapidity to growth of these cracking, making necessary evaluations which can to predict its behavior, therefore the present work shows the preliminary results for determining the behavior to the fracture of an AISI 304 stainless steel sensitized, in a dynamic recirculation circuit which allows to simulate the operation conditions of a BWR reactor (288 Centigrade and 80 kg/cm{sup 2}). (Author)

Multi-scale analysis of behavior and fatigue life of 304L stainless under cyclic loading with pre-hardening

International Nuclear Information System (INIS)

Belattar, A.

2013-01-01

This study investigates the effects of loading history on the cyclic stress-strain curve and fatigue behavior of 304L stainless steel at room temperature. Tension-compression tests were performed on the same specimen under controlled strain, using several loading sequences of increasing or decreasing amplitude. The results showed that fatigue life is significantly reduced by the previous loading history. A previously developed method for determining the effect of prehardening was evaluated. Microstructural analyses were also performed; the microstructures after pre-loading and their evolution during the fatigue cycles were characterized by TEM. The results of these analyses improve our understanding of the macroscopic properties of 304L stainless steel and can help us identify the causes of failure and lifetime reduction. (author)

Behavior of stressed and unstressed 304L specimens in tuff repository environmental conditions

International Nuclear Information System (INIS)

Juhas, M.C.; McCright, R.D.; Garrison, R.E.

1984-11-01

This paper presents preliminary results of an investigation of the behavior of candidate barrier material for high-level nuclear waste storage, Type 304L stainless steel, in tuff repository environmental conditions. Tuff is a densely welded, devitrified, igneous rock common to the proposed repository site at Yucca Mountain, Nevada. The results discussed include: irradiation corrosion tests, U-bend irradiation corrosion tests, slow strain rate tests, and bent beam stress corrosion tests. Results indicate that Type 304L stainless steel shows excellent resistance to general, localized, and stress corrosion under the environmental and microstructural conditions tested so far. The environmental test conditions are 50 to 100 0 C J-13 well water (non-saline, near neutral pH, and oxic in nature) and saturated steam at 100 0 C. Microstructural conditions include solution annealed and long furnace heat treatments to provoke a sensitized structure. However, this particular type of stainless steel may be susceptible to long-term, low-temperature sensitization because of the combination of expected time at elevated temperature and residual stress in the container after emplacement in the repository. Other grades of austenitic stainless steels are reported to be more resistant to low-temperature sensitization. Future work will therefore include more extensive testing of these grades. 15 references, 5 figures, 7 tables

Effect of Low-Temperature Sensitization on the Corrosion Behavior of AISI Type 304L SS Weld Metal in Simulated Groundwater

Science.gov (United States)

Suresh, Girija; Nandakumar, T.; Viswanath, A.

2018-05-01

The manuscript presents the investigations carried out on the effect of low-temperature sensitization (LTS) of 304L SS weld metal on its corrosion behavior in simulated groundwater, for its application as a canister material for long-term storage of nuclear vitrified high-level waste in geological repositories. AISI type 304L SS weld pad was fabricated by multipass gas tungsten arc welding process using 308L SS filler wire. The as-welded specimens were subsequently subjected to carbide nucleation and further to LTS at 500 °C for 11 days to simulate a temperature of 300 °C for 100-year life of the canister in geological repositories. Delta ferrite ( δ-ferrite) content of the 304L SS weld metal substantially decreased on carbide nucleation treatment and further only a marginal decrease occurred on LTS treatment. The microstructure of the as-welded consisted of δ-ferrite as a minor phase distributed in austenite matrix. The δ-ferrite appeared fragmented in the carbide-nucleated and LTS-treated weld metal. The degree of sensitization measured by double-loop electrochemical potentokinetic reactivation method indicated an increase in carbide nucleation treatment when compared to the as-welded specimens, and further increase occurred on LTS treatment. Potentiodynamic anodic polarization investigations in simulated groundwater indicated a substantial decrease in the localized corrosion resistance of the carbide-nucleated and LTS 304L SS weld metals, when compared to the as-welded specimens. Post-experimental micrographs indicated pitting as the primary mode of attack in the as-welded, while pitting and intergranular corrosion (IGC) occurred in the carbide-nucleated weld metal. LTS-treated weld metal predominantly underwent IGC attack. The decrease in the localized corrosion resistance of the weld metal after LTS treatment was found to have a direct correlation with the degree of sensitization and the weld microstructure. The results are detailed in the manuscript.

Effect of Low-Temperature Sensitization on the Corrosion Behavior of AISI Type 304L SS Weld Metal in Simulated Groundwater

Science.gov (United States)

Suresh, Girija; Nandakumar, T.; Viswanath, A.

2018-04-01

The manuscript presents the investigations carried out on the effect of low-temperature sensitization (LTS) of 304L SS weld metal on its corrosion behavior in simulated groundwater, for its application as a canister material for long-term storage of nuclear vitrified high-level waste in geological repositories. AISI type 304L SS weld pad was fabricated by multipass gas tungsten arc welding process using 308L SS filler wire. The as-welded specimens were subsequently subjected to carbide nucleation and further to LTS at 500 °C for 11 days to simulate a temperature of 300 °C for 100-year life of the canister in geological repositories. Delta ferrite (δ-ferrite) content of the 304L SS weld metal substantially decreased on carbide nucleation treatment and further only a marginal decrease occurred on LTS treatment. The microstructure of the as-welded consisted of δ-ferrite as a minor phase distributed in austenite matrix. The δ-ferrite appeared fragmented in the carbide-nucleated and LTS-treated weld metal. The degree of sensitization measured by double-loop electrochemical potentokinetic reactivation method indicated an increase in carbide nucleation treatment when compared to the as-welded specimens, and further increase occurred on LTS treatment. Potentiodynamic anodic polarization investigations in simulated groundwater indicated a substantial decrease in the localized corrosion resistance of the carbide-nucleated and LTS 304L SS weld metals, when compared to the as-welded specimens. Post-experimental micrographs indicated pitting as the primary mode of attack in the as-welded, while pitting and intergranular corrosion (IGC) occurred in the carbide-nucleated weld metal. LTS-treated weld metal predominantly underwent IGC attack. The decrease in the localized corrosion resistance of the weld metal after LTS treatment was found to have a direct correlation with the degree of sensitization and the weld microstructure. The results are detailed in the manuscript.

Fatigue of welded joint in a stainless steel AISI 304 L

International Nuclear Information System (INIS)

Kuromoto, N.K.; Guimaraes, A.S.; Miranda, P.E.V. de

1986-01-01

The flexion fatigue behavior for the base metal and welded joint of an AISI 304 L stainless steel type, used in the Angra-1 reactor, was determined. An automatic welding process was used with improved procedures in order to assure better welding metallurgy. Fatigue tests samples reinforcements were done to allow the evaluation of metallurgical variables, specially the role played by delta ferrite. The resulting welded joint showed better fatigue life than the base metal. Delta ferrite was found to play an important role on the initiation and propagation processes of the fatigue cracks. (Author) [pt

Carburization behavior under the pits induced by metal dusting in 304L and 347 stainless steels

Energy Technology Data Exchange (ETDEWEB)

Chang, Chia-Hao [Department of Materials Engineering and Science, National Cheng Kung University, Tainan 701, Taiwan (China); Tsai, Wen-Ta, E-mail: wttsai@mail.ncku.edu.tw [Department of Materials Engineering and Science, National Cheng Kung University, Tainan 701, Taiwan (China)

2009-08-15

The metal dusting behavior of Type 304L and 347 stainless steels (SSs) in a flowing mixed CO/H{sub 2}/H{sub 2}O gas stream at 600 deg. C was investigated. After exposure in a 35% CO + 60% H{sub 2} + 5% H{sub 2}O gas for 500 h, large pits were formed on both steel surfaces. The aspect ratio of the pits formed in 304L SS was higher than that of the pits formed in 347 SS. The microstructures and chemical compositions of the reaction products and those of the substrate under the pits were examined by using a scanning electron microscope (SEM) combined with an energy dispersive spectrometer (EDS). A Cr-depleted zone containing voids was formed on the outer surface just beneath the pit. Massive matrix carburization and intergranular carbide precipitation were seen for both steels. The experimental results showed that niobium (Nb) could delay the ingress of carbon and retard the metal dusting reaction.

Cladding of aluminum on AISI 304L stainless steel by cold roll bonding: Mechanism, microstructure, and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Akramifard, H.R., E-mail: akrami.1367@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Mirzadeh, H., E-mail: hmirzadeh@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Advanced Metalforming and Thermomechanical Processing Laboratory, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Parsa, M.H., E-mail: mhparsa@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Center of Excellence for High Performance Materials, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Advanced Metalforming and Thermomechanical Processing Laboratory, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2014-09-08

The AA1050 aluminum alloy and AISI 304L stainless steel sheets were stacked together to fabricate Al/304L/Al clad sheet composites by the cold roll bonding process, which was performed at temperatures of ∼100 and 23 °C to produce austenitic and austenitic–martensitic microstructures in the AISI 304L counterpart, respectively. The peel test results showed that the threshold reduction required to make a suitable bond at room temperature is below 10%, which is significantly lower than the required reduction for cold roll bonding of Al sheets. The tearing of the Al sheet during the peel test signified that the bond strength of the roll bonded sheets by only 38% reduction has reached the strength of Al, which is a key advantage of the developed sheets. The extrusion of Al through the surface cracks and settling inside the 304L surface valleys due to strong affinity between Al and Fe was found to be the bonding mechanism. Subsequently, the interface and tensile behaviors of three-layered clad sheets after soaking at 200–600 °C for 1 h were investigated to characterize the effect of annealing treatment on the formation and thickening of intermetallic compound layer and the resultant mechanical properties. Field emission scanning electron microscopy, X-ray diffraction, and optical microscopy techniques revealed that an intermediate layer composed mainly of Al{sub 13}Fe{sub 4}, FeC and Al{sub 8}SiC{sub 7} forms during annealing at 500–600 °C. A significant drop in tensile stress–strain curves after the maximum point (UTS) was correlated to the interface debonding. It was found that the formation of intermediate layer by post heat treatment deteriorates the bond quality and encourages the debonding process. Moreover, the existence of strain-induced martensite in clad sheets was found to play a key role in the enhancement of tensile strength.

Stainless-Steel-Gadolinium Alloys; Alliages Acier Inoxydable-Gadolinium; Splavy iz nerzhaveyushchej stali i gadoliniya; Aleaciones de Acero Inoxidable-Gadolinio

Energy Technology Data Exchange (ETDEWEB)

Copeland, M.; Kato, H. [Albany Metallurgy Research Center, Bureau Of Mines, United States Department of the Interior, Albany, OR (United States)

1964-06-15

mineures ont une grande influence sur les structures resultant de traitements equilibrants et sur les possibilites de transformation des aciers. Lorsque le gadolinium est melange a de l 'acier au chrome et au nickel, deux phases mineures, Fe{sub 9}Gd et Ni{sub 7}Gd, fondent a 1080 Degree-Sign C, ce qui impose une limite superieure aux temperatures de traitement a chaud et de transformation. Les auteurs ont pu facilement transformer des alliages comprenant jusqu'a 5 Degree-Sign Io en poids de gadolinium et determiner leurs caracteristiques mecaniques et leur resistance a la corrosion. Ils n'ont observe aucun changement dans les caracteristiques mecaniques de l'acier ou sa resistance a la corrosion par l'eau chaude, lorsqu'ils lui ont ajoute'jusqu'a 3% en poids de gadolinium. En raison des limites imposees aux temperatures de transformation des aciers au chrome et au nickel par le point de fusion des phases mineures, les auteurs ont etudie les effets du gadolinium sur des aciers au chrome. Ils ont releve une seule phase mineure qui fond a 1320 Degree-Sign C en etudiant l 'isoplethe du gadolinium a 10% en poids dans l 'alliage chrome-fer-gadolinium. Cette propriete permettrait d'equilibrer et de transformer ces aciers au gadolinium aux temperatures auxquelles on opere normalement. (author) [Spanish] En vista de la excelente resistencia a la corrosion de los aceros inoxidables y del interes que presenta el gadolinio como veneno nuclear, se han estudiado aleaciones de esos dos metales. El gadolinio fue aleado con aceros inoxidables de tipo AISI-304 y al cromo, y se estudiaron las relaciones de fase, la facilidad de trabajo y las propiedades de estas aleaciones. Se observo que en las aleaciones que contienen bajos porcentajes de gadolinio, los puntos de fusion de las fases menores ejercen un efecto muy marcado sobre las estructuras resultantes de los tratamientos de equilibracion y sobre la facilidad de trabajo de los afceros. Cuando se alea el gadolinio con acerce al cromo

Microstructure and mechanical properties of friction welded AISI 1040/AISI 304L steels before and after electrochemical corrosion

Energy Technology Data Exchange (ETDEWEB)

Sarsilmaz, Furkan [Firat Univ., Elazig (Turkey). Dept. of Mechatronics Engineering; Kirik, Ihsan [Batman Univ. (Turkey); Ozdemir, Niyazi [Firat Univ., Elazig (Turkey)

2018-03-01

The aim of the present study is to investigate the effect of welding parameters both on the electrochemical corrosion behavior and tensile strength of pre- and post-electrochemical corrosion of friction welded dissimilar steels. The microstructural changes of AISI 1040/AISI 304L friction welded couples and also parent materials were analyzed by using scanning electron microscopy. The electrochemical behaviors of AISI1040/AISI304L joints were comparatively investigated by potentiodynamic polarization curve test and by electrochemical impedance spectra. Moreover, tensile strength experiments were carried out determining the behavior of friction welded joints of pre- and post-electrochemical corrosion and results indicated that the maximum tensile test value of the dissimilar welded pre-electrochemical corrosion was higher than those of post-electrochemical corrosion and was also very close to AISI 1040 parent material value.

Electrodos austeníticos inoxidables semisintéticos para la soldadura manual por arco eléctrico: Una variante económica para las pequeñas y medianas empresas (PIME. // Semi-synthetic austenitics stainless steel electrodes for shielded metal arc welding: A

Directory of Open Access Journals (Sweden)

A. Paz Iglesias

2002-09-01

Full Text Available En el presente trabajo se brinda una valoración económica para la producción de electrodos austeníticos inoxidables tiposE308L, E309, E312 y E316L en las pequeñas y medianas empresas (PIME. Lo significativo de la presente valoración esque se brindan los resultados obtenidos al fabricar los electrodos de forma semisintética; es decir, utilizando un solo tipo dealambre inoxidable (308L y añadiendo las ferroaleaciones necesarias en el revestimiento. Los resultados que se muestranestán basados en las experiencias de investigación, producción y comercialización de una planta con capacidad para 200toneladas al año, a la cual le es muy difícil insertarse en el mercado utilizando los mismos procedimientos tecnológicos yfinancieros de una gran empresa con grandes capitales y recursos.Palabras claves: Electrodos austeníticos inoxidables, electrodos sintéticos, ferroaleaciones, electrodossemisintéticos, electrodos convencionales, metal depositado.___________________________________________________________________Abstract.This paper offers an economic valuation for the production of stainless electrodes type E308L, E309, E312 and E316L,for small and middle companies (PIME. The significant part of the present valuation gives the results obtained in theproduction of semi-synthetic electrodes; using just one type of stainless wire (308L and adding the ferroalloys neededin the coat. The results shown are based on investigation experiences, production and trading of companies with acapacity for 200 T/year, so it is very difficult to enter in the market using the same technological procedures of a bigcompany with higher capital and financial resources.Key words: Nonrusting austenistic electrodes, sintetic electrodes, semisintetic electrodes, iron alloy,conventional electrodes, metal deposition.

Improvement of pitting corrosion resistance of AISI 304L stainless steel by nano-pulsed laser surface melting

International Nuclear Information System (INIS)

Pacquentin, W.; Blanc, C.; Caron, N.; Thro, P.Y.; Cheniere, A.; Tabarant, M.; Moutiers, G.; Miserque, F.; Plouzennec, H.; Oltra, R.

2013-01-01

The stainless steel 304L is widely used, however, in particular conditions, it may be sensitive to pitting corrosion. Nano-pulsed laser surface melting is a surface treatment which allows improving the corrosion resistance of this steel. This treatment consists in focusing a laser beam on the surface of the material, involving its quite immediately melting through a few microns depth, then an ultra-fast solidification occurs with cooling rate about 1011 K/s. The laser parameters control the modifications of the physico-chemical properties. In particular, we studied the influence of the impacts overlap of an ytterbium laser-fiber on the corrosion resistance of a 304L stainless steel in conditions of an aerated and agitated solution of NaCl (concentration of 30 g/L). We obtained an increase of the pitting potential of 220 mV, highlighting an improvement of the corrosion resistance. The study of the chemical and structural modifications is not enough to explain the improvement of the corrosion resistance. Other phenomena must be taken into account, as the quality of the oxide layer, in terms of physico-chemical and mechanical properties. (authors)

Superficial and electrochemical study of stainless steel 304l with an inhibitory protective coating (TiO{sub 2} and ZrO{sub 2}); Estudio superficial y electroquimico de acero inoxidable 304L con una capa protectora inhibidora (TiO{sub 2} y ZrO{sub 2})

Energy Technology Data Exchange (ETDEWEB)

Davila N, M. L.; Contreras R, A.; Arganis J, C. R., E-mail: aida.contreras@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2014-10-15

The degradation mechanisms in the boiling water reactors (BWR) have been an alert focus for owners, especially the cracking by stress corrosion cracking (SCC), therefore different techniques have been studied to inhibit this problem inside which is the water injection of hydrogen feeding (HWC, Hydrogen Water Chemistry), together with the noble metals injection (NMCA, Nobel Metal Chemical Addition) and the ceramic materials injection that form an inhibitory protective coating (Ipc). In this work the Ipc was simulated, for which were carried out hydro-thermals deposits starting from suspensions of 1000 ppm of zirconium oxide in its crystalline phase baddeleyite and titanium oxides in its anatase and rutile phases, on test tubes of stainless steel 304l previously rusty under simulated conditions of pressure and temperature of a BWR (288 C and 8 MPa). The superficial characterization was realized by scanning electron microscopy, energy-dispersive of X-ray and X-ray diffraction. The capacity to mitigate the corrosion was studied with the electrochemical technique of Tafel polarization (288 C and 8 MPa). The steel presents the formation of two oxide coatings formed by magnetite and hematite. The baddeleyite presents a deposit more thick and homogeneous it also presents the most negative electrochemical potential of corrosion, what indicates that it has the bigger capacity to mitigate the SCC. (Author)

Martensitic Transformation in Ultrafine-Grained Stainless Steel AISI 304L Under Monotonic and Cyclic Loading

Directory of Open Access Journals (Sweden)

Heinz Werner Höppel

2012-02-01

Full Text Available The monotonic and cyclic deformation behavior of ultrafine-grained metastable austenitic steel AISI 304L, produced by severe plastic deformation, was investigated. Under monotonic loading, the martensitic phase transformation in the ultrafine-grained state is strongly favored. Under cyclic loading, the martensitic transformation behavior is similar to the coarse-grained condition, but the cyclic stress response is three times larger for the ultrafine-grained condition.

Resistência à corrosão de junta dissimilar soldada pelo processo TIG composta pelos aços inoxidáveis AISI 316L e AISI 444

Directory of Open Access Journals (Sweden)

Luis Henrique Guilherme

2014-03-01

Full Text Available O aço inoxidável AISI 444 tornou-se uma opção para substituir a liga AISI 316L devido ao seu menor custo e satisfatória resistência à corrosão. Entretanto, o uso da liga AISI 444 no feixe tubular de trocadores de calor acarreta na soldagem de uma junta dissimilar. O presente estudo teve por objetivo avaliar a resistência à corrosão da junta tubo-espelho soldada pelo processo TIG composta pelas ligas AISI 316L e AISI 444. A manufatura das amostras consistiu em replicar o projeto da junta tubo-espelho de trocadores de calor. Realizou-se em juntas soldadas ensaios de sensitização, perda de massa por imersão desde a temperatura ambiente até 90 ºC, e ensaios eletroquímicos de polarização potenciodinâmica nos eletrólitos 0,5 mol/L de HCl e 0,5 mol/L de H2SO4. Os resultados mostraram que a junta dissimilar sofreu corrosão galvânica com maior degradação na zona afetada pelo calor (ZAC do tubo AISI 444. Porém, os mecanismos de corrosão localizada (pite e intergranular demonstraram ser mais ativos para a liga AISI 316L. Conclui-se que a junta dissimilar apresentou melhor resistência à corrosão do que a junta soldada composta unicamente pela liga AISI 316L em temperaturas de até 70 ºC, conforme as condições observadas neste trabalho.

Experimental investigation of Ti–6Al–4V titanium alloy and 304L stainless steel friction welded with copper interlayer

Directory of Open Access Journals (Sweden)

R. Kumar

2015-03-01

Full Text Available The basic principle of friction welding is intermetallic bonding at the stage of super plasticity attained with self-generating heat due to friction and finishing at upset pressure. Now the dissimilar metal joints are especially popular in defense, aerospace, automobile, bio-medical, refinery and nuclear engineerings. In friction welding, some special alloys with dual phase are not joined successfully due to poor bonding strength. The alloy surfaces after bonding also have metallurgical changes in the line of interfacing. The reported research work in this area is scanty. Although the sound weld zone of direct bonding between Ti–6Al–4V and SS304L was obtained though many trials, the joint was not successful. In this paper, the friction welding characteristics between Ti–6Al–4V and SS304L into which pure oxygen free copper (OFC was introduced as interlayer were investigated. Box–Behnken design was used to minimize the number of experiments to be performed. The weld joint was analyzed for its mechanical strength. The highest tensile strength between Ti–6Al–4V and SS304L between which pure copper was used as insert metal was acquired. Micro-structural analysis and elemental analysis were carried out by EDS, and the formation of intermetallic compound at the interface was identified by XRD analysis.

Moessbauer spectroscopy and X-ray diffraction study of 304 L stainless steel thin films

International Nuclear Information System (INIS)

Boubeker, B.; Eymery, J.P.; Goudeau, P.; Sayouty, E.H.

1994-01-01

304 L stainless steel films (SS) were elaborated using an ion-beam sputtering technique. The target material was a sheet of commercial grade 304 L SS. The starting material was first analysed by both conversion electron Moessbauer spectroscopy (CEMS) and X-ray diffraction. The nonmagnetic state and f.c.c. structure of this material were confirmed. The films were deposited on various substrates with thicknesses in the 175-800 nm range. The films are found to have both b.c.c. structure and ferromagnetic character. X-ray diffraction technique was also used in order to determine the residual stresses developed during the deposition process. The second stage of the work is devoted to the evolution of the film structure as a function of annealing treatments. So isochronal and isothermal kinetics at temperatures higher than 913 K have allowed to follow the alpha --> gamma phase transformation using X-ray diffraction and CEMS technique.The X-ray diffractograms reveal the existence of both b.c.c. and f.c.c. phases. Similar results can be deduced from Moessbauer spectra due to the single line coming from the non-magnetic phase and the sextet coming from the ferromagnetic phase. In addition the CEMS spectra reveal that the ferromagnetic component is split into two parts which indicates the existence of two iron sites. 1 fig., 4 refs.(author)

Dependence of corrosion properties of AISI 304L stainless steel on the austenite grain size

Energy Technology Data Exchange (ETDEWEB)

Sabooni, Soheil; Rashtchi, Hamed; Eslami, Abdoulmajid; Karimzadeh, Fathallah; Enayati, Mohammad Hossein; Raeissi, Keyvan; Imani, Reihane Faghih [Isfahan Univ. of Technology, Isfahan (Iran, Islamic Republic of). Dept. of Materials Engineering; Ngan, Alfonso Hing Wan [The Univ. of Hong Kong (China). Dept. of Mechanical Engineering

2017-07-15

The corrosion resistance of austenitic stainless steels is known to be hampered by the loss of chromium available for passive surface layer formation as a result of chromium carbide precipitation at austenite grain boundaries during annealing treatments. Although high-temperature annealing can promote carbide dissolution leading to better corrosion resistance, grain coarsening also results, which would lead to poorer mechanical properties. Processing methods to achieve both good corrosion resistance and mechanical properties are thus highly desirable for austenitic stainless steels. In the present study, we show that the corrosion resistance of AISI 304L stainless steel can be improved by grain refinement into the ultrafine-grained regime. Specifically, samples with different austenite grain sizes in the range of 0.65-12 μm were studied by potentiodynamic polarization and electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution. All samples showed a typical passive behavior with similar corrosion potential, but the corrosion current density decreased significantly with decreasing grain size. The results show that the sample with the finest grain size had the best corrosion resistance due to a higher resistance of the passive layer to pitting attacks. This study indicates that grain refinement which improves mechanical properties can also significantly improve the corrosion resistance of AISI 304L stainless steel.

Chemical sanitizers to control biofilms formed by two Pseudomonas species on stainless steel surface Sanificantes químicos no controle de biofilmes formados por duas espécies de Pseudomonas em superfície de aço inoxidável

Directory of Open Access Journals (Sweden)

Danila Soares Caixeta

2012-03-01

Full Text Available The biofilm formation of Pseudomonas aeruginosa and Pseudomonas fluorescens on AISI 304 stainless steel in the presence of reconstituted skim milk under different temperatures was conducted, and the potential of three chemical sanitizers in removing the mono-species biofilms formed was compared. Pseudomonas aeruginosa cultivated in skim milk at 28 °C presented better growth rate (10.4 log CFU.mL-1 when compared with 3.7 and 4.2 log CFU.mL-1 for P. aeruginosa and P. fluorescens cultivated at 7 °C, respectively. Pseudomonas aeruginosa formed biofilm when cultivated at 28 °C. However, only the adhesion of P. aeruginosa and P. fluorescens was observed when incubated at 7 °C. The sodium dichloroisocyanurate was the most efficient sanitizer in the reduction of the adhered P. aeruginosa cells at 7 and 28 °C and those on the biofilm, respectively. The hydrogen peroxide was more effective in the reduction of adhered cells of P. fluorescens at 7 °C.A capacidade de adesão e formação de biofilme por Pseudomonas aeruginosa e Pseudomonas fluorescens em aço inoxidável AISI 304, na presença de leite desnatado resconstituído sobre diferentes temperaturas foi conduzido e o potencial de três sanificantes químicos na remoção de biofilmes monoespécies foi comparado. Pseudomonas aeruginosa cultivada em leite desnatado a 28 °C apresentou melhor crescimento (10,4 log UFC.mL-1 quando comparado com 3,7 and 4,2 log UFC.mL-1 para P. aeruginosa e P. fluorescens cultivadas a 7 °C, respectivamente. Pseudomonas aeruginosa formou biofilme quando cultivada a 28 °C. Contudo foi observado somente adesão de P. aeruginosa e P. fluorescens quando incubada a 7 °C. O dicloroisocianurato de sódio foi o sanificante mais eficiente na redução de células aderidas e em biofilme de P. aeruginosa a 7 e 28 °C, respectivamente. O peróxido de hidrogênio foi o mais eficiente na redução de células aderidas de P. fluorescens a 7 °C.

Effect of SiC particle impact nano-texturing on tribological performance of 304L stainless steel

Science.gov (United States)

Lorenzo-Martin, C.; Ajayi, O. O.

2014-10-01

Topographical features on sliding contact surfaces are known to have a significant impact on friction and wear. Indeed, various forms of surface texturing are being used to improve and/or control the tribological performance of sliding surfaces. In this paper, the effect of random surface texturing produced by a mechanical impact process is studied for friction and wear behavior of 304L stainless steel (SS) under dry and marginal oil lubrication. The surface processing was applied to 304L SS flat specimens and tested under reciprocating ball-on-flat sliding contact, with a 440C stainless steel ball. Under dry contact, the impact textured surface exhibited two order of magnitude lower wear than the isotropically ground surface of the same material. After 1500 s of sliding and wearing through of the processed surface layer following occurring of scuffing, the impact textured surface underwent a transition in wear and friction behavior. Under marginal oil lubrication, however, no such transition occurred, and the wear for the impact textured surface was consistently two orders of magnitude lower than that for the ground material. Mechanisms for the tribological performance enhancement are proposed.

Influencia de la microestructura en el comportamiento a fatiga de aceros inoxidables austeníticos con alto contenido en molibdeno

Directory of Open Access Journals (Sweden)

Oñoro, J.

2006-02-01

Full Text Available Austenitic stainless steels with molybdenum present high mechanical properties and corrosion resistance to aggressive environments. These steels have been used to tank and vessel components for high corrosive liquids as phosphoric, nitric and sulphuric acids. These materials with low carbon and nitrogen addition have been proposed candidates as structural materials for the international thermonuclear experimental reactor (ITER in-vessel components. Molybdenum addition in austenitic stainless steel improves mechanical and corrosion properties, but with it can produce the presence of nitrogen microstructure modifications by presence or precipitation of second phases. This paper summarises the fatigue and corrosion fatigue behaviour of two 317LN stainless steels with different microstructure. Fully austenitic steel microstructure show better fatigue, corrosion fatigue resistance and better ductility than austenitic steel with delta ferrite microstructure, mainly at low stresses.

Los aceros inoxidables austeníticos con elevados contenidos en molibdeno presentan alta resistencia mecánica y resistencia a los medios corrosivos. Se utilizan en la construcción de depósitos y recipientes para el almacenamiento y transporte de líquidos altamente corrosivos, tales como ácido fosfórico, nítrico o sulfúrico. Estos materiales con bajo carbono y adiciones de nitrógeno han sido propuestos como candidatos para materiales estructurales en la fabricación de la vasija del reactor experimental termonuclear internacional (ITER. La adición de molibdeno mejora las propiedades frente a la corrosión de los aceros inoxidables austeníticos. Sin embargo, este aumento del contenido en molibdeno, junto con la presencia de nitrógeno, puede producir modificaciones microestructurales, por la aparición de fases precipitadas o segundas fases. En este trabajo, se analiza el comportamiento la fatiga y corrosión-fatiga de dos aceros inoxidables austen

Weld solidification cracking in 304 to 204L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Hochanadel, Patrick W [Los Alamos National Laboratory; Lienert, Thomas J [Los Alamos National Laboratory; Martinez, Jesse N [Los Alamos National Laboratory; Johnson, Matthew Q [Los Alamos National Laboratory

2010-09-15

A series of annulus welds were made between 304 and 304L stainless steel coaxial tubes using both pulsed laser beam welding (LBW) and pulsed gas tungsten arc welding (GTAW). In this application, a change in process from pulsed LBW to pulsed gas tungsten arc welding was proposed to limit the possibility of weld solidification cracking since weldability diagrams developed for GTAW display a greater range of compositions that are not crack susceptible relative to those developed for pulsed LBW. Contrary to the predictions of the GTAW weldability diagram, cracking was found.This result was rationalized in terms of the more rapid solidification rate of the pulsed gas tungsten arc welds. In addition, for the pulsed LBW conditions, the material compositions were predicted to be, by themselves, 'weldable' according to the pulsed LBW weldability diagram. However, the composition range along the tie line connecting the two compositions passed through the crack susceptible range. Microstructurally, the primary solidification mode (PSM) of the material processed with higher power LBW was determined to be austenite (A), while solidification mode of the materials processed with lower power LBW apparently exhibited a dual PSM of both austenite (A) and ferrite-austenite (FA) within the same weld. The materials processed by pulsed GTAW showed mostly primary austenite solidification, with some regions of either primary austenite-second phase ferrite (AF) solidification or primary ferrite-second phase austenite (FA) solidification. This work demonstrates that variations in crack susceptibility may be realized when welding different heats of 'weldable' materials together, and that slight variations in processing can also contribute to crack susceptibility.

Influência da velocidade de circulação do leite na adesão de Pseudomonas aeruginosa sobre aço inoxidável The speed of milk circulation influences the adhesion of Pseudomonas aeruginosa on stainless steel

Directory of Open Access Journals (Sweden)

Hamilton Mendes de Figueiredo

2009-09-01

Full Text Available A influência da velocidade de circulação do leite na adesão bacteriana de Pseudomonas aeruginosa foi avaliada em teste de uso simulado por meio de um modelo de circuito de processamento de leite. O circuito é composto por uma tubulação de aço inoxidável AISI 304, com 1,9 cm de diâmetro e 5,8 m de comprimento, além de um tanque de 25 L, utilizado como reservatório do produto e das soluções sanitizantes. O reservatório foi acoplado a uma bomba centrífuga de ½ HP, para impulsionar o alimento ou soluções de higienização pelo sistema equipado com cupons de prova em aço inoxidável nas formas cilíndrica, cotovelo 90º e T. As velocidades de circulação foram de 0,5, 1,0 e 1,5 m.s-1, correspondentes a fluxo turbulento com número de Reynolds de 14.000, 28.000 e 42.000, respectivamente. Quando se utilizou velocidade de 0,5 m.s-1, permaneceram aderidas à superfície 10,7% das células. Já nas velocidades e 1,0 e 1,5 m.s-1 as porcentagens de adesão foram de 5,36 e 4,9%, respectivamente, o que demonstra uma menor remoção de células aderidas à medida que o fluxo diminui, permitindo assim que mais células permaneçam aderidas na linha de produção, o que pode favorecer a formação de biofilmes.The influence of the flow milk circulation in the bacterial adhesion of Pseudomonas aeruginosa was evaluated by simulation tests through a circuit model of milk processing. The circuit is composed of a tubulation of stainless steel AISI 304, with 1.9 cm of diameter, 5.8 m of length and a tank of 25 L used as the reservoir of the product and sanitizer solutions. The reservoir was coupled to a centrifugal bomb of ½ HP to impel the food or sanitizer solutions for the system equipped with 90º and T cylindrical stainless steel specimens. The speed of circulation values were 0.5, 1.0 and 1.5 m.s-1, corresponding to turbulent flow with number of Reynolds 14.000, 28.000 and 42.000, respectively. When flow of 0.5 m.s-1 was used 10.7% the

Modeling of residual stress state in turning of 304L

International Nuclear Information System (INIS)

Valiorgue, F.; Rech, J.; Bergheau, J.M.

2010-01-01

Research presented in this paper aims to link machining parameters to residual stress state and helps understanding mechanisms responsible of machined surface properties modifications. The first presented works are based on an experimental campaign. They reproduce the finishing turning operation of 304L and allow observing the residual stress state evolution at the work piece surface and for an affected depth of 0.2 mm for such processes. Then, the finishing turning operation is simulated numerically in order to realize the same sensitivity study to cutting parameters. This simulation is based on an hybrid approach mixing experimental data and numerical simulation. This method allows getting round the classical difficulties of turning simulation by applying equivalent thermo mechanical loadings onto the work piece surface without modeling the material separation phenomena. Moreover the numerical model uses an hardening law taking into account dynamic recrystallization phenomena. (authors)

Physical characterization of austenitic stainless steels AISI 304 and AISI 348 L*

International Nuclear Information System (INIS)

Teodoro, Celso Antonio; Silva, Jose Eduardo Rosa da

2009-01-01

The study of radiation damages in metals and metallic alloys used as structural materials in nuclear reactors has a strategic meaning to the nuclear technology because it treats of performance of these materials in conditions that simulate the conditions of work in power reactors. Then it becomes necessary to know the essential physical properties of these materials, properties that are sensitive to the microstructural changes that occurred during the irradiation. The purpose of this work is to characterize, initially, some pre-irradiation properties of the stainless steels AISI 304 and AISI 348 L * , such as mechanical (stress-strain and microhardness) and electrical (resistivity). The AISI 348 L * has been studied for use as fuel cladding material. Both materials will be tested after irradiation in the IEA-R1 core and their properties will be compared with those in the pre-irradiated condition. The morphology of the fractured zones after tensile tests was observed using SEM (scanning electron microscopy). (author)

Effect of H2O2 on the corrosion behavior of 304L stainless steel

International Nuclear Information System (INIS)

Song, Taek Ho

1994-02-01

In connection with the safe storage of high level nuclear waste, effect of H 2 O 2 on the corrosion behavior of 304L stainless steel was examined. Open circuit potentials and polarization curves were measured with and without H 2 O 2 . The experimental results show that H 2 O 2 increased corrosion potential and decreased pitting potential. The passive range, therefore, decreased as H 2 O 2 concentration increased, indicating that pitting resistance was decreased by the existence of H 2 O 2 in the electrolyte. These effects of H 2 O 2 on corrosion of 304L stainless steel are considered to be similar to those of γ-irradiation. To compare the effects of H 2 O 2 with those of O 2 , cathodic and anodic polarization curves were made in three types of electrolyte such as aerated, deaerated, and stirred electrolyte. The experimental results show that the effects of H 2 O 2 on the corrosion behavior were very similar to those of O 2 such as increase of corrosion potential, decrease of pitting resistance, and increase of repassivation potential. Further, H 2 O 2 played much greater role in controlling cathodic reaction rate in neutral water environment. In acid and alkaline media, potential shifts by H 2 O 2 were restricted by the large current density of proton reduction and by the le Chatelier's principle respectively

Effect of H2O2 on the corrosion behavior of 304L stainless steel

International Nuclear Information System (INIS)

Song, Taek Hoh; Kim, In Sub; Noh, Sung Kee

1995-01-01

In connection with the safe storage of high level nuclear waste, effect of H 2 O 2 on the corrosion behavior of 304L stainless steel was examined. Open circuit potentials and polarization curves were measured with and without H 2 O 2 . The experimental results show that H 2 O 2 increased corrosion potential and decreased pitting potential. The passive range, therefore, decreased as H 2 O 2 concentration increased, indicating that pitting resistance was decreased by the existence of H 2 O 2 in the electrolyte. These effects of H 2 O 2 on corrosion of 304L stainless steel are considered to be similar to those of γ-irradiation. To compare the effects of H 2 O 2 with those of O 2 , cathodic and anodic polarization curves were made in three types of electrolyte such as aerated, deaerated, and stirred electrolyte. The experimental results show that the effects of H 2 O 2 on the corrosion behavior were very similar to those of O 2 such as increase of corrosion potential, decrease of pitting resistance, and increase of repassivation potential. In acid and alkaline media, the corrosion potential shifts by H 2 O 2 were restricted by the large current density of proton reduction and by the le Chatelier's principle respectively. 13 figs., 1 tabs., 17 refs. (Author)

Corrosion behavior of mild steel and SS 304L in presence of dissolved nickel under aerated and deaerated conditions

Directory of Open Access Journals (Sweden)

Mohd Mobin

2011-12-01

Full Text Available In dual purpose water/power co-generation plants, the presence of high concentration of Cu and Ni in the re-circulating brine/condensate as a result of condenser tubes corrosion has been attributed as one of the several causes of corrosion damage of flash chamber materials and water touched parts of the boilers. The present investigation deals with the effect of dissolved nickel in the concentration range of 10 ppb to 100 ppm on the corrosion behavior of mild steel and SS 304L in two aqueous medium namely, distilled water and artificial seawater. The effect of pH, dissolved oxygen and flow condition of aqueous medium on the corrosion behavior was also monitored. The experimental techniques include immersion test and electrochemical tests which include free corrosion potential measurements and potentiodynamic polarization measurements. The corrosion rate of mild steel and SS 304L under different experimental conditions was determined by weight loss method and spectrophotometric determination of iron ion entered into the test solution during the period of immersion. The pH of the test solution was also monitored during the entire period of immersion. The left over nickel ions present in the test solution after completion of immersion was also estimated using Atomic Absorption Spectrophotometer. The surface morphology of the corroded steel surface was also examined using scanning electron microscopy (SEM. The results of the studies show that SS 304L largely remains unaffected in both distilled water and artificial seawater under different experimental conditions. However, the effect of nickel on the corrosion behavior of mild steel is quite pronounced and follows interesting trends.

Effect of microstructure and chemical composition on localized corrosion resistance of a AISI 304L stainless steel after nanopulsed-laser surface melting

International Nuclear Information System (INIS)

Pacquentin, W.; Caron, N.; Oltra, R.

2015-01-01

Highlights: • Laser surface melting treatments require neither additional feedstock nor contact. • By affecting 1 μm, the pitting potential of laser treated 304L increases by 500 mV. • Surface modification of laser treated sample observed by TEM. • The physico-chemical properties of the surface are correlated to overlap rate. • AISI 304L pitting corrosion resistance strongly depends of overlap rate. - Abstract: Changes induced in the surface properties of AISI 304L stainless steel when it is treated with a nanopulsed ytterbium-doped fiber laser were investigated to determine the microscale distribution of its physico-chemical properties. A Gaussian energy distribution was created with a radius of 71 μm (1/e 2 ) at the focal point. Local investigations were carried out using transmission electron microscopy to consider the effect of overlapping individual laser impacts. The results obtained reveal that laser surface melting leads to changes in the crystallographic structure of the steel through the formation of a δ-ferritic phase. It also results in the creation of an oxide layer that increases the corrosion resistance of the steel, with the chemical composition, structure and thickness of this layer being dependent on the overlap percentage and the position along the beam radius. Measurement of the localized corrosion resistance in a 30 g L −1 NaCl solution using polarization curves found that optimal laser treatment conditions can led to an increase in the breakdown potential of more than 500 mV, which corresponds to a significant improvement in corrosion resistance.

Impact of Defects in Powder Feedstock Materials on Microstructure of 304L and 316L Stainless Steel Produced by Additive Manufacturing

Science.gov (United States)

Morrow, Benjamin M.; Lienert, Thomas J.; Knapp, Cameron M.; Sutton, Jacob O.; Brand, Michael J.; Pacheco, Robin M.; Livescu, Veronica; Carpenter, John S.; Gray, George T.

2018-05-01

Recent work in both 304L and 316L stainless steel produced by additive manufacturing (AM) has shown that in addition to the unique, characteristic microstructures formed during the process, a fine dispersion of sub-micron particles, with a chemistry different from either the powder feedstock or the expected final material, are evident in the final microstructure. Such fine-scale features can only be resolved using transmission electron microscopy (TEM) or similar techniques. The present work uses electron microscopy to study both the initial powder feedstock and microstructures in final AM parts. Special attention is paid to the chemistry and origin of these nanoscale particles in several different metal alloys, and their impact on the final build. Comparisons to traditional, wrought material will be made.

Soldagem por Difusão de Aços Inoxidáveis para Fabricação de Trocadores de Calor Compactos

Directory of Open Access Journals (Sweden)

Marcus Vinícius Volponi Mortean

2016-03-01

Full Text Available Resumo A união de materiais diferentes ou componentes com geometrias complexas muitas vezes requer processos de uniões especiais, como por exemplo, uma fonte de energia de alta densidade como laser ou feixe de elétrons para soldagem por fusão ou mesmo um processo de soldagem no estado sólido. Em particular, este trabalho descreve os experimentos recentes da aplicação da soldagem por difusão no estado sólido (SDES para diferentes tipos de aços inoxidáveis: austenítico AISI 316L, duplex UNS 31803 e superduplex UNS 327250. A soldagem por difusão foi realizada sob alto vácuo a 1050 °C, durante 60 minutos, empregando uma pressão uniaxial de 18-35 MPa. A qualidade da união foi avaliada por microscopia óptica e testes mecânicos. Os resultados preliminares indicam a necessidade de otimização dos parâmetros de processo para os aços duplex e superduplex. Os resultados positivos alcançados no presente trabalho permitiram a fabricação de protótipos de trocadores de calor compacto em aço inoxidável, utilizando o novo método de fabricação, desenvolvido por LABTUCAL / UFSC, através do qual o processo de corte a jato de água é aplicado para confeccionar com precisão os canais do núcleo do permutador de calor.

Swelling of AISI 304L in response to simultaneous variations in stress and displacement rate

International Nuclear Information System (INIS)

Porter, D.L.; Garner, F.A.

1984-01-01

The duration of the transient regime of neutron-induced swelling in annealed AISI 304L at 400 0 C is sensitive to both stress and displacement rate variations. The simultaneous application of both variables exerts a synergistic effect on the transient regime. The duration of this regime cannot be reduced below a required intrinsic exposure of approx. 10 dpa, however, which has been found to be characteristic of all Fe-Ni-Cr austenitic alloys. This is four times larger than that currently assumed in the stress-affected swelling equation for 20% cold-worked AISI 316

Corrosion of high Ni-Cr alloys and Type 304L stainless steel in HNO3-HF

International Nuclear Information System (INIS)

Ondrejcin, R.S.; McLaughlin, B.D.

1980-04-01

Nineteen alloys were evaluated as possible materials of construction for steam heating coils, the dissolver vessel, and the off-gas system of proposed facilities to process thorium and uranium fuels. Commercially available alloys were found that are satisfactory for all applications. With thorium fuel, which requires HNO 3 -HF for dissolution, the best alloy for service at 130 0 C when complexing agents for fluoride are used is Inconel 690; with no complexing agents at 130 0 C, Inconel 671 is best. At 95 0 C, six other alloys tested would be adequate: Haynes 25, Ferralium, Inconel 625, Type 304L stainless steel, Incoloy 825, and Haynes 20 (in order of decreasing preference); based on composition, six untested alloys would also be adequate. The ions most effective in reducing fluoride corrosion were the complexing agents Zr 4+ and Th 4+ ; Al 3+ was less effective. With uranium fuel, modestly priced Type 304L stainless steel is adequate. Corrosion will be most severe in HNO 3 -HF used occasionally for flushing and in solutions of HNO 3 and corrosion products (ferric and dichromate ions). HF corrosion can be minimized by complexing the fluoride ion and by passivation of the steel with strong nitric acid. Corrosion caused by corrosion products can be minimized by operating at lower temperatures

Comparative study of the microbiological corrosion among an AISI 304L and an API X65; Estudio comparativo de la corrosion microbiologica entre un AISI 304L y un API X65

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Gonzalez F, E. [ITT, Toluca, Estado de Mexico (Mexico)

2004-07-01

Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

Modelling of cyclic plasticity for austenitic stainless steels 304L, 316L, 316L(N)-IG

Energy Technology Data Exchange (ETDEWEB)

Dalla Palma, Mauro, E-mail: mauro.dallapalma@igi.cnr.it

2016-11-01

Highlights: • Stress-strain amplitudes of cyclic stress strain curves defined by design codes are provided as reference data. • A macroinstruction simulating cyclic plasticity and producing hardening parameters of constitutive models is developed. • Hardening parameters of the nonlinear Chaboche model are provided for stainless steels 316l-N, 316L, 304L at different temperatures. • Ratcheting is simulated by using the produced hardening parameters. - Abstract: The integrity assessment of structures subjected to cyclic loading must be verified with regard to cyclic type damage including time-independent fatigue and progressive deformation or ratcheting. Cyclic damage is verified simulating the material elastic-plastic loop and looking at the accumulated net plastic strain during each cycle at all points of the structure subjected to the complete time history of loadings. This work deals with the development of a numerical model producing the Chaboche hardening parameters starting from stress-strain data produced by testing of materials. Then, the total plastic strain can be simulated using the Chaboche inelastic constitutive model requested for finite element analyses. This is particularly demanding for pressure vessels, pressurised piping, boilers, and mechanical components of nuclear installations made of stainless steels. A design optimisation by iterative analyses is developed to approach the stress-strain test data with the Chaboche model. The parameters treated as design variables are the Chaboche parameters and the objective function to be minimised is a combination of the deviations from test data. The optimiser calls a macroinstruction simulating cyclic loading of a sample for different material temperatures. The numerical model can be used to produce hardening parameters of materials for inelastic finite element verifications of structures with complex joints like elbows subjected to a combination of steady sustained and cyclic loads.

El refractario en la fabricación de acero inoxidable

Directory of Open Access Journals (Sweden)

Ferrer, F. J.

2006-10-01

Full Text Available The influence of the steelmaking process on the quality and the performance of refractory materials used on stainless steel production was described. The most important technical and design parameters of the processing units were explained and related with the slag chemical composition and the qualities of the refractories used.

Se describe la influencia del proceso siderúrgico sobre el tipo y rendimiento del material refractario utilizado en la producción de acero inoxidable. Tras describir las distintas unidades implicadas en el proceso metalúrgico se hace especial énfasis en la importancia que ejercen el diseño de las distintas unidades y el tipo y control de la escoria sobre la calidad del tipo de refractario a utilizar.

Vida a la fatiga de juntas soldadas del acero inoxidable AISI 316L obtenidas mediante el proceso GMAW

Directory of Open Access Journals (Sweden)

Puchi-Cabrera, E. S.

2007-06-01

Full Text Available An investigation has been conducted in order to determine the effect of both the metallic transfer mode (pulsed arc or short circuit and the O2 content in the Ar/O2 gas mixture, of the gas-metal arc welding process (GMAW, on the fatigue life under uniaxial conditions of welded joints of 316L stainless steel. It has been concluded that the mixture of the protective gases employed in the process could have an important influence on the fatigue life of the welded joints of such steel in two different ways. Firstly, through the modification of the radius of curvature at the joint between the welding toe and the base metal and, secondly, through a more pronounced degree of oxidation of the alloying elements induced by a higher O2 content in the mixture. As far as the metallic transfer mode is concerned, it has been determined that the welded joints obtained under a pulsed arc mode show a greater fatigue life in comparison with the joints obtained under short circuit for both gas mixtures.

Se ha llevado a cabo una investigación con la finalidad de determinar el efecto, tanto del modo de transferencia metálica (arco pulsado o cortocircuito como del contenido de O2 en la mezcla de gases protectores Ar/O2, del proceso de soldadura a tope mediante arco metálico con protección gaseosa (GMAW, sobre la vida a la fatiga en condiciones uniaxiales de juntas soldadas del acero inoxidable AISI 316L. Dicho trabajo ha permitido concluir que la composición de la mezcla de gases protectores del proceso GMAW pudiera tener una influencia importante en la vida a la fatiga de las juntas soldadas de dicho material, a través de dos formas distintas: primero, mediante la modificación del radio de curvatura entre la raíz del cordón de soldadura y el metal base y, en segundo lugar, a través del mayor grado de oxidación de los elementos de aleación. En cuanto al modo de transferencia metálica, se determinó que las juntas soldadas mediante arco pulsado

Evolution of microstructure in laser welding of SS304L

International Nuclear Information System (INIS)

Kumar, Santosh; Kushwaha, R.P.; Viswanadham, C.S.; Dey, G.K.

2009-01-01

Laser welding is an important joining process and its application in industries is growing rapidly. One can produce laser welds over a wide range of process parameters and this offers very good opportunity for producing microstructure of different morphology and scales in the weldment. Weld beads have been produced on 5 mm thick plates of SS304L using CW Nd-YAG laser. Laser power was varied in 200 W to 1000 W range and welding speed was varied in 100 mm/mm to 1000 mm/mm. This resulted in weld beads of different morphology. Microstructure of the weld beads was examined on the cross-section as well as in the axial direction using optical microscopy and Transmission Electron Microscopy (TEM) to study evolution of the microstructure in the weldment. Microstructure was cellular and cellular-dendritic with grains growing from the fusion line towards the centerline. In the central region, cellular growth along the welding direction was observed. The cell size was found to increase with increasing laser power and decreasing welding speed. The findings are presented in this paper. (author)

Effect of surface grinding on chloride induced SCC of 304L

Energy Technology Data Exchange (ETDEWEB)

Zhou, Nian, E-mail: nzh@du.se [Department of Material Science, Dalarna University, SE-79188 Falun (Sweden); KTH, SE-10044 Stockholm (Sweden); Pettersson, Rachel [KTH, SE-10044 Stockholm (Sweden); Jernkontoret, SE-11187 Stockholm (Sweden); Lin Peng, Ru [Department of Management and Engineering, Linköping University, SE-58183 Linköping (Sweden); Schönning, Mikael [Corrosion Department, Avesta Research Centre – Outokumpu Stainless AB, SE-774 22 Avesta (Sweden)

2016-03-21

The effect of surface grinding on the stress corrosion cracking (SCC) behavior of 304L austenitic stainless steel in boiling magnesium chloride has been investigated. SCC tests were conducted both without external loading and with varied levels of four-point bend loading for as-delivered material and for specimens which had been ground parallel or perpendicular to the loading direction. Residual stresses due to the grinding operation were measured using the X-ray diffraction technique. In addition, surface stress measurements under applied load were performed before exposure to evaluate the deviation between actual applied loading and calculated values according to ASTM G39. Micro-cracks initiated by a high level of tensile residual stress in the surface layer were observed for all the ground specimens but not those in the as-delivered condition. Grinding along the loading direction increased the susceptibility to chloride induced SCC; while grinding perpendicular to the loading direction improved SCC resistance. Surface tensile residual stresses were largely relieved after the initiation of cracks.

Effect of surface grinding on chloride induced SCC of 304L

International Nuclear Information System (INIS)

Zhou, Nian; Pettersson, Rachel; Lin Peng, Ru; Schönning, Mikael

2016-01-01

The effect of surface grinding on the stress corrosion cracking (SCC) behavior of 304L austenitic stainless steel in boiling magnesium chloride has been investigated. SCC tests were conducted both without external loading and with varied levels of four-point bend loading for as-delivered material and for specimens which had been ground parallel or perpendicular to the loading direction. Residual stresses due to the grinding operation were measured using the X-ray diffraction technique. In addition, surface stress measurements under applied load were performed before exposure to evaluate the deviation between actual applied loading and calculated values according to ASTM G39. Micro-cracks initiated by a high level of tensile residual stress in the surface layer were observed for all the ground specimens but not those in the as-delivered condition. Grinding along the loading direction increased the susceptibility to chloride induced SCC; while grinding perpendicular to the loading direction improved SCC resistance. Surface tensile residual stresses were largely relieved after the initiation of cracks.

Evaluation at 290 degrees Celsius and 8 MPa of the anticorrosion properties of hydrothermal ceramic nano deposits on preoxidized 304l Ss

Energy Technology Data Exchange (ETDEWEB)

Lopez G, N.; Marin A, M.; Medina A, A. L. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Galicia A, G., E-mail: natali_log@hotmail.com [Universidad Veracruzana, Instituto de Ingenieria, Av. Juan Pablo II s/n, Fracc. Costa Verde, 94294 Boca del Rio, Veracruz (Mexico)

2017-09-15

In the present paper, we present the electrochemical evaluation carried out under reductive conditions (molar ratio H{sub 2}:O{sub 2} >5), at 290 degrees Celsius and 8 MPa, of preoxidized 304l Ss with hydrothermal deposits of nanoparticles of TiO{sub 2} and ZrO{sub 2}. The anticorrosion properties of the deposits were studied by Electrochemical Impedance Spectroscopy (EIS) and Linear Polarization Resistance (LPR). After electrochemical tests, the samples were characterized by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (Sem). It was found by EIS that both, ZrO{sub 2} and TiO{sub 2} produce an increase in the charge transfer resistance (R{sub CT}) of preoxidized 304l Ss. At the same time, by LPR we observed that the studied ceramic nano deposits decrease the corrosion rate (Cr) and corrosion current density (i{sub corr}), however, in most of the cases the Electrochemical Corrosion Potential (Ecp) is slightly higher in the presence of the ceramic nano deposits that the one of preoxidized 304l Ss. After holding time at 290 degrees Celsius, when the impedance (Z) increases, the capacitance increases also, which is attributed to a surface increase due to the roughness of the oxide formed at this temperature under a reductive environment. The observed electrochemical behavior has a dependence on the homogeneity and thickness of the deposits, as has been corroborated by Sem and XRD. The best electrochemical results are obtained when two conditions are fulfilled: The bigger the effective coated area and the lower the deposit thickness. (Author)

The application of an internal state variable model to the viscoplastic behavior of irradiated ASTM 304L stainless steel

Energy Technology Data Exchange (ETDEWEB)

McAnulty, Michael J., E-mail: mcanulmj@id.doe.gov [Department of Energy, 1955 Fremont Avenue, Idaho Falls, ID 83402 (United States); Potirniche, Gabriel P. [Mechanical Engineering Department, University of Idaho, Moscow, ID 83844 (United States); Tokuhiro, Akira [Mechanical Engineering Department, University of Idaho, Idaho Falls, ID 83402 (United States)

2012-09-15

Highlights: Black-Right-Pointing-Pointer An internal state variable approach is used to predict the plastic behavior of irradiated metals. Black-Right-Pointing-Pointer The model predicts uniaxial tensile test data for irradiated 304L stainless steel. Black-Right-Pointing-Pointer The model is implemented as a user-defined material subroutine in the finite element code ABAQUS. Black-Right-Pointing-Pointer Results are compared for the unirradiated and irradiated specimens loaded in uniaxial tension. - Abstract: Neutron irradiation of metals results in decreased fracture toughness, decreased ductility, increased yield strength and increased ductile-to-brittle transition temperature. Designers use the most limiting material properties throughout the reactor vessel lifetime to determine acceptable safety margins. To reduce analysis conservatism, a new model is proposed based on an internal state variable approach for the plastic behavior of unirradiated ductile materials to support its use for analyzing irradiated materials. The proposed modeling addresses low temperature irradiation of 304L stainless steel, and predicts uniaxial tensile test data of irradiated experimental specimens. The model was implemented as a user-defined material subroutine (UMAT) in the finite element software ABAQUS. Results are compared between the unirradiated and irradiated specimens subjected to tension tests.

Measurement of carbon activity in sodium by Fe-Mn 20% alloy, and by strainless austenitic steel 304L and 316L

International Nuclear Information System (INIS)

Oberlin, C.; Saint Paul, P.; Baque, P.; Champeix, L.

1980-01-01

Precise knowledge of carbon activity in sodium used as coolant in fast breeder reactors, is essential for continuous survey of carburization-decarburization processes. Carbon activity can be periodically surveyed by measuring the carbon concentration or by hot trap like metal alloy strip placed in sodium loop. In fact, in equilibrium, activity of carbon in sodium is equal to the activity in metal alloy. Thus if the relation between concentration of carbon and it activity in the alloy is known, it is possible to estimate the activity of carbon in sodium. Materials to be used should have high solubility in carbon at the needed temperature. They should quickly attain equilibrium with sodium and they should not contain impurities that can affect the results. Materials chosen according to these criteria were Fe-Mn 20%, stainless austenitic steel AISI 304L and 316L

CORROSION STUDY FOR THE EFFLUENT TREATMENT FACILITY CHROME (VI) REDUCTANT SOLUTION USING 304 AND 316L STAINLESS STEEL

Energy Technology Data Exchange (ETDEWEB)

DUNCAN JB; WYRAS RB

2007-10-08

This report documents the laboratory testing and analyses as directed under the test plan, RPP PLAN-34065, and documented in laboratory notebooks HNF 2742 and HNF-N-473-1. The purpose of this study was to evaluate and compare the electrochemical corrosion and pitting susceptibility of the 304 and 316L stainless steel in the acidified reducing solution that will be contained in either the secondary waste receiving tank or concentrate tank.

Análisis experimental del desgaste entre UHMWPE y acero inoxidable 316l empleados en la manufactura de prótesis coxofemorales

Directory of Open Access Journals (Sweden)

Ricardo Gustavo Rodríguez Cañizo

2010-07-01

Full Text Available Título en inglés: Experimental wear analysis of UHMWPE and stainless 316l used in the manufacturing of coxofemoral prosthesis. Resumen La causa más común de falla en prótesis coxofemorales es el aflojamiento entre los componentes que conforman el sistema, de manera específica la copa acetabular y la cabeza femoral. En esta investigación se presenta un análisis tribológico del desgaste en los componentes mencionados, ya que cuando las superficies en contacto se desgastan, la funcionalidad mecánica del sistema se compromete, debido al cambio de geometría de los mismos, dando como resultado un juego mecánico entre la copa y la cabeza. Los materiales considerados en este estudio son el polietileno de ultra elevado peso molecular (UHMWPE, por sus siglas en inglés para la copa acetabular, y acero inoxidable 316L para la cabeza femoral. Esta combinación de materiales representa hoy en día la recomendación más usual por parte de los cirujanos para pacientes de la tercera edad. La tasa anual de desgaste se determinó de manera experimental y se cuantificó la cantidad de material desprendido durante el contacto. Se establecieron las condiciones de carga de forma analítica, considerando las que actúan sobre la cabeza femoral a lo largo del área de desgaste durante la marcha humana. Posteriormente, se realizó el análisis experimental de desgaste utilizando una máquina tribológica de configuración perno-sobre-disco (pin-on-disk, diseñada de manera específica para este estudio. Las pruebas para determinar la pérdida volumétrica de los componentes se realizaron bajo tres condiciones de operación: en seco, lubricada con agua destilada y lubricada con suero bovino. El marco experimental considerado consistió en pernos de UHMWPE sobre discos de acero inoxidable 316L simulando el desgaste equivalente a diez años de uso de la prótesis. Finalmente, de los resultados obtenidos se puede establecer que el desgaste y la cantidad de part

Deposición electroforética de una porcelana dental sobre acero inoxidable austenítico 304

Directory of Open Access Journals (Sweden)

Vargas, G.

2003-02-01

Full Text Available An alternative technique for the production of dental restorations with porcelain, is the electrophoretic deposition (EPD. In this work, deposits of dental porcelain on stainless steel were obtained by EPD using water, ethanol and isopropanol as suspension mediums. The effect of the porcelain concentration, the intensity of the electric field and the suspension medium on the quantity of deposited mass were studied. All the tests were carried out at constant voltage, using a deposition time of 3 min. The particle size of the dental porcelain was in the range between 1.5 and 2.3 μm in the suspension. The results showed that the porcelain in the aqueous medium presented the major deposition velocity, in comparison with both ethanol and isopropanol. However, due to low the low suspension stability and hydrolysis of the water problems, the best coating finishes were obtained with ethanol. These results were obtained applying voltages between 70 and 150 V, for a deposition time of 3 min. Using isopropanol heterogeneous deposits were obtained due to the low suspension stability and to electrochemical reactions problems in the working electrodes, resulted from the high voltages application.

Una técnica alternativa para la fabricación de restauraciones dentales con porcelana, es la deposición electroforética (EPD. En este trabajo depósitos de porcelana dental sobre acero inoxidable fueron obtenidos por EPD utilizando como medios de suspensión: agua, etanol e isopropanol. Se estudió el efecto de la concentración de porcelana, de la intensidad del campo eléctrico y del medio de suspensión sobre la cantidad de masa depositada. Todas las pruebas fueron realizadas a voltaje constante, utilizando un tiempo de deposición de 3 min. La porcelana dental utilizada presentó un intervalo de tamaño de partícula entre 1,5 y 2,3 μm. Los resultados mostraron que la porcelana en el medio acuoso presentó la mayor velocidad de deposición, en

Optimización topológica y fabricación aditiva de un soporte aeronáutico mediante sinterizado láser de acero inoxidable 15-5PH

OpenAIRE

Marchal Montes, Álvaro

2016-01-01

El objetivo de este trabajó será la aplicación de la optimización topológica a un soporte usado en el sector aeronáutico para reducir su masa que posteriormente se fabricará mediante fabricación aditiva con tecnología DMLS (Direct Metal Laser Sintering) en acero inoxidable 15-5PH. Para llegar a una buena optimización topológica será necesario estudiar todos los caminos de optimización posibles hasta llegar a una correcta mediante softwares adecuados además de adaptarla a la fabricación ad...

Effect of strain-path on stress corrosion cracking of AISI 304L stainless steel in PWR primary environment at 360 deg. C

International Nuclear Information System (INIS)

Couvant, T.; Vaillant, F.; Boursier, JM.; Delafosse, D.

2004-01-01

Austenitic stainless steels (ASS) are widespread in primary and auxiliary circuits of PWR. Moreover, some components suffer stress corrosion cracking (SCC) under neutron irradiation. This degradation could be the result of the increase of hardness or the modification of chemical composition at the grain boundary by irradiation. In order to avoid complex and costly corrosion facilities, the effects of irradiation on the material are commonly simulated by applying a cold work on non-irradiated material prior to stress corrosion cracking tests. Slow strain rate tests were conducted on an austenitic stainless steel (SS) AISI 304L in PWR environment (360 deg. C). Particular attention was directed towards pre-straining effects on crack growth rate (CGR) and crack growth path (CGP). Results have demonstrated that the susceptibility of 304L to SCC in high-temperature hydrogenated water was enhanced by pre-straining. It seemed that IGSCC was enhanced by complex strain paths. (authors)

Análise microestrutural e tenacidade ao impacto da ZAC do aço inoxidável ferrítico com 11%Cr

Directory of Open Access Journals (Sweden)

Temístocles de Sousa Luz

2013-09-01

Full Text Available O aço inoxidável ferrítico possibilita, em função de suas características, o uso em diversos campos da engenharia. Dentre esses é possível citar a industria do petróleo e gás, de celulose açucareira, de transporte, entre outras. Atualmente, o desenvolvimento de novas ligas para a substituição dos aços ao carbono no que se refere ao setor de transporte de carga, levou muitos fabricantes a adotarem a liga ferrítica com base de cromo entre 11% e 12%, implementando a tal situação, uma maior vida util. A utilização dessa nova classe de aço inoxidável ferrítico gera uma demanda no que tange à pesquisas das soldas desses aços. Neste trabalho, buscou-se analisar a região soldada de um aço inoxidável ferrítico experimental contendo 11% de cromo, realizando para tal um estudo de sua microestrutura, e tenacidade ao impacto do metal de base e da zona afetada pelo calor (ZAC. A avaliação mostrou bons resultados nas propriedades mecânicas medidas nas duas regiões analisadas. Entretanto, verificou-se uma perda acentuada da tenacidade ao impacto na ZAC em relação ao metal de base.

Simulation of Friction Stir Processing in 304L Stainless Steel

Directory of Open Access Journals (Sweden)

Miles M.P.

2016-01-01

Full Text Available A major dilemma facing the nuclear industry is repair or replacement of stainless steel reactor components that have been exposed to neutron irradiation. When conventional fusion welding is used for weld repair, the high temperatures and thermal stresses inherent in the process enhance the growth of helium bubbles, causing intergranular cracking in the heat-affected zone (HAZ. Friction stir processing (FSP has potential as a weld repair technique for irradiated stainless steel, because it operates at much lower temperatures than fusion welding, and is therefore less likely to cause cracking in the HAZ. Numerical simulation of the FSP process in 304L stainless steel was performed using an Eulerian finite element approach. Model input required flow stresses for the large range of strain rates and temperatures inherent in the FSP process. Temperature predictions in three locations adjacent to the stir zone were accurate to within 4% of experimentally measure values. Prediction of recrystallized grain size at a location about 6mm behind the tool center was less accurate, because the empirical model employed for the prediction did not account for grain growth that occurred after deformation in the experiment was halted.

STUDY AND ANALYSIS OF THE EFFECT OF WELDING PROCESS ON DISTORTION WITH 304L STAINLESS STEEL WELD JOINTS

OpenAIRE

Dhananjay Kumar*, Dharamvir mangal

2017-01-01

The effect of welding process on the distortion with 304L stainless steel 12thk weld joints made by TIG (tungsten inert gas) and SMAW (Shielded metal arc welding) welding process involving different type joint configuration have been studied. The joint configurations employed were double V-groove edge preparation for double side SMAW welding and square – butt preparation for double side TIG welding. All weld joints passed by radiographic. Distortion measurements were carried out using height ...

Reassessment of the swelling behavior of AISI 304 stainless steel

International Nuclear Information System (INIS)

Garner, F.A.; Porter, D.L.

1982-03-01

Published swelling data derived from EBR-II irradiations of AISI 304 and 304L have been reanalyzed in light of insights gained from irradiation of AISI 316 and Fe-15Cr-25Ni. The primary influence of temperature, displacement rate and compositional variations in the 300 series stainless steels lies in the duration of the transient regime of swelling and not in the steady-state or constant swelling rate regime

EFECTO DE LA TEMPERATURA SOBRE LA RESISTENCIA A LA TRACCIÓN DE ALGUNOS REFUERZOS DE FIBRAS PARA MATRICES CERÁMICAS O POLIMÉRICAS EFEITO DA TEMPERATURA SOBRE A RESISTÊNCIA À TRAÇÃO DE ALGUNS REFORZOS DE FIBRAS PARA MATRIZES CERÁMICAS OU POLIMÉRICAS EFFECT OF TEMPERATURE ON TH E TENSILE STRENGTH OF SOME FIBER REINFORCEMENTS FOR CERAMIC OR POLYMER MATRICES

Directory of Open Access Journals (Sweden)

MARYORY ASTRID GÓMEZ

2009-07-01

Full Text Available Este artículo presenta un estudio de las propiedades termomecánicas de fibras de acero de bajo carbono, de acero inoxidable ASI-SAE 304, de aramida y de carbono. Además, se analizó el aspecto superficial de refuerzos de lana mineral de roca y lana de aluminosilicatos antes y después de someterlos a tratamientos térmicos a 1000 ºC. La resistencia a la tracción de las fibras se evaluó antes y después de someterlas a tratamientos térmicos a temperaturas de 400, 600, 800 y 1000 ºC dependiendo de la degradación que mostraran. Además, se efectuó un análisis termogravimétrico a cada tipo de fibra para determinar los cambios de peso a diferentes temperaturas. Las fibras de acero inoxidable mostraron la mayor estabilidad termomecánica, mientras que las fibras de aramida con tratamientos a 400 ºC mostraron propiedades mecánicas prácticamente nulas.Este artigo apresenta um estudo das propriedades termomecánicas de fibras de aço baixo carbono, de aço inoxidável ASI-SAE 304, de aramida e de carbono. Além disso, se analisou o aspecto superficial de reforços de lã mineral de rocha e lã de aluminosilicatos antes e depois que submetê-las a tratamentos térmicos a 1000 ºC. A resistência à tração das fibras se avaliou antes e depois de submetê-las a tratamentos térmicos a temperaturas de 400, 600, 800 e 1000 ºC dependendo da degradação que mostraram. Além disso, se efetuou uma análise termogravim étrica a cada tipo de fibra para determinar as mudanças de peso a diferentes temperaturas. As fibras de aço inoxidável mostraram a maior estabilidade termomecânica, enquanto as fibras de aramida com tratamentos a 400 ºC mostraram propriedades mecânicas praticamente nulas.This paper presents a study of the thermomechanical properties of low carbon steel, AISI-SAE 304 stainless steel, aramid and carbon fibers. Moreover, surface aspect of mineral rock wool of and aluminosilicate wool reinforcements was analyzed prior and after

The role of martensitic transformation on bimodal grain structure in ultrafine grained AISI 304L stainless steel

International Nuclear Information System (INIS)

Sabooni, S.; Karimzadeh, F.; Enayati, M.H.; Ngan, A.H.W.

2015-01-01

In the present study, metastable AISI 304L austenitic stainless steel samples were subjected to different cold rolling reductions from 70% to 93%, followed by annealing at 700 °C for 300 min to form ultrafine grained (UFG) austenite with different grain structures. Transmission electron microscopy (TEM) and nanoindentation were used to characterize the martensitic transformation, in order to relate it to the bimodal distribution of the austenite grain size after subsequent annealing. The results showed that the martensite morphology changed from lath type in the 60% rolled sample to a mixture of lath and dislocation-cell types in the higher rolling reductions. Calculation of the Gibbs free energy change during the reversion treatment showed that the reversion mechanism is shear controlled at the annealing temperature and so the morphology of the reverted austenite is completely dependent on the morphology of the deformation induced martensite. It was found that the austenite had a bimodal grain size distribution in the 80% rolled and annealed state and this is related to the existence of different types of martensite. Increasing the rolling reduction to 93% followed by annealing caused changing of the grain structure to a monomodal like structure, which was mostly covered with small grains of around 300 nm. The existence of bimodal austenite grain size in the 80% rolled and annealed 304L stainless steel led to the improvement of ductility while maintaining a high tensile strength in comparison with the 93% rolled and annealed sample

Effect of H{sub 2}O{sub 2} on the corrosion behavior of 304L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Song, Taek Hoh; Kim, In Sub [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Noh, Sung Kee [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-08-01

In connection with the safe storage of high level nuclear waste, effect of H{sub 2}O{sub 2} on the corrosion behavior of 304L stainless steel was examined. Open circuit potentials and polarization curves were measured with and without H{sub 2}O{sub 2}. The experimental results show that H{sub 2}O{sub 2} increased corrosion potential and decreased pitting potential. The passive range, therefore, decreased as H{sub 2}O{sub 2} concentration increased, indicating that pitting resistance was decreased by the existence of H{sub 2}O{sub 2} in the electrolyte. These effects of H{sub 2}O{sub 2} on corrosion of 304L stainless steel are considered to be similar to those of {gamma}-irradiation. To compare the effects of H{sub 2}O{sub 2} with those of O{sub 2}, cathodic and anodic polarization curves were made in three types of electrolyte such as aerated, deaerated, and stirred electrolyte. The experimental results show that the effects of H{sub 2}O{sub 2} on the corrosion behavior were very similar to those of O{sub 2} such as increase of corrosion potential, decrease of pitting resistance, and increase of repassivation potential. In acid and alkaline media, the corrosion potential shifts by H{sub 2}O{sub 2} were restricted by the large current density of proton reduction and by the le Chatelier`s principle respectively. 13 figs., 1 tabs., 17 refs. (Author).

Investigation of high temperature phase stability, thermal properties and evaluation of metallurgical compatibility with 304L stainless steel, of indigenously developed ferroboron alternate shielding material for fast reactor applications

Energy Technology Data Exchange (ETDEWEB)

Rai, Arun Kumar [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603102 (India); Raju, S., E-mail: sraju@igcar.gov.in [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603102 (India); Jeya Ganesh, B. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603102 (India); Panneerselvam, G. [Chemistry Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603102 (India); Vijayalakshmi, M.; Jayakumar, T. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603102 (India); Raj, Baldev [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603102 (India); Chemistry Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603102 (India)

2011-08-15

Highlights: > High temperature phase stability and metallurgical compatibility of indigenous Ferro boron alloy (17 wt.%) with 304L SS have been evaluated using calorimetry, metallography and X-ray diffraction. > Fe-B is stable upto 1227 deg. C without any phase transformation. > In combination with SS 304L, it develops an eutectic reaction at 1198 deg. C. > High temperature metallurgical interaction between Ferroboron and 304L SS clad has been simulated for temperatures 550-800 deg. C for reaction times up to 5000 h, using diffusion couple. > Clad penetration depth with time follows a paraobolic rate law. - Abstract: Towards the cause of serving economic power production through fast reactors, it is necessary to bring in functionally more efficient and innovative design options, which also includes exploration of cheaper material alternatives, wherever possible. In this regard, the feasibility of using a commercial grade ferroboron alloy as potential alternate shielding material in the outer subassemblies of future Indian fast reactors has been recently investigated from shielding physics point of view. The present study explores in detail the high temperature thermal stability and the metallurgical compatibility of Fe-15.4B-0.3C-0.89Si-0.17Al-0.006S-0.004P-0.003O (wt.%) alloy with SS 304L material. In addition, the high temperature specific heat and lattice thermal expansion characteristics of this alloy have also been investigated as a part of the present comprehensive characterisation program. The Fe-15 wt.%B alloy is constituted of principally of two boride phases, namely tetragonal Fe{sub 2}B and orthorhombic FeB phases, which in addition to boron also contains some amount of C and Si dissolved in solid solution form. This Fe-B alloy undergoes a series of phase transformation as a function of increasing temperature; the major ones among them are the dissolution of Fe{sub 2}B-lower boride in the matrix through a eutectic type reaction, which results in the

Junções de materiais dissimilares utilizando o processo de soldagem por fricção rotativa

OpenAIRE

Eder Paduan Alves

2010-01-01

O objetivo desse trabalho é o desenvolvimento de junções no estado sólido de materiais dissimilares alumínio AA 1050 e aço inoxidável AISI 304, que possam ser utilizadas nas tubulações de reservatórios de propelentes líquidos e demais tubulações dos Veículos Lançadores de Satélites. As junções foram obtidas pelo processo de soldagem por fricção rotativa convencional, que combina o calor gerado entre o atrito de duas superfícies e deformação mecânica. Foram realizados testes de soldagem com di...

Biaxial fatigue tests and crack paths for AISI 304L stainless steel

Directory of Open Access Journals (Sweden)

V. Chaves

2014-10-01

Full Text Available AISI 304L stainless steel specimens have been tested in fatigue. The tests were axial, torsional and in-phase biaxial, all of them under load control and R=-1. The S-N curves were built following the ASTM E739 standard and the method of maximum likelihood proposed by Bettinelli. The fatigue limits of the biaxial tests were represented in axes σ-τ. The elliptical quadrant, appropriate for ductile materials, and the elliptical arc, appropriate for fragile materials, were included in the graph. The experimental values were better fitted with an elliptical quadrant, despite the ratio between the pure torsion and tension fatigue limits, τFL/σFL, is 0.91, close to 1, which is a typical value for fragile materials. The crack direction along the surface has been analyzed by using a microscope, with especial attention to the crack initiation zones. The crack direction during the Stage I has been compared with theoretical models.

Corrosion of type 304L stainless steel in boiling dilute neptunium nitrate solution

International Nuclear Information System (INIS)

Motooka, Takafumi; Kiuchi, Kiyoshi

2003-01-01

Corrosion of type 304L stainless steel in nitric acid solution containing neptunium was studied under immersion and heat-transfer condition. Corrosion rates of stainless steel were obtained by the weight loss measurement and the quantitative analysis of metallic ions dissolved in solution. The surface morphology was observed by scanning electron microscopy. The corrosion acceleration mechanism was investigated by polarization measurement and spectrophotometry. The corrosion rate in boiling 9M nitric acid was accelerated by addition of neptunium. The corrosion of stainless steel was promoted under heat-transfer condition compared to immersion condition. In polarization measurements, the cathodic current was increased by addition of neptunium. Spectrophotometric measurements showed the oxidization of neptunium in boiling nitric acid. It was suggested that the accelerated corrosion in nitric acid solution containing neptunium was caused by re-oxidation of neptunium. (author)

Estudio in vitro de la citotoxicidad y genotoxicidad de los productos liberados del acero inoxidable 316L con recubrimientos cerámicos bioactivos Cytotoxic and genotoxic study of in Vitro released products of stainless Steel 316l with bioactive ceramic Coatings

Directory of Open Access Journals (Sweden)

María Elena Márquez Fernández

2007-03-01

Full Text Available El acero inoxidable AISI 316L es el biomaterial mas utilizado para la fabricación de implantes temporales, pero presenta limitaciones para implantes permanentes debido a la liberación de iones metálicos hacia los tejidos circundantes, produciendo especies reactivas de oxígeno (ERO y daño en ADN, factores que aumentan el riesgo de aparición de tumores locales y fallas mecánicas del implante. Una estrategia utilizada para disminuir la liberación de iones es la modificación superficial de los implantes metálicos por medio de recubrimientos inorgánicos, cerámicos o vítreos, aplicados por el método sol-gel, el cual presenta una serie de ventajas comparativas con otras técnicas de deposición, como buena adherencia, aplicación sencilla, mínimos problemas de secado, bajas temperaturas de densificación y posibilidad de agregar partículas y/o grupos orgánicos que mejoran la adherencia celular al implante aumentando su biocompatibilidad. En el presente trabajo se evaluaron los efectos citotóxico por medio de la técnica MTT, y genotóxico por electroforesis en gel de células individuales (Ensayo Cometa, sobre células de la línea celular CHO, de los productos liberados en medio MEM por el acero inoxidable 316L sin recubrir, recubierto con una monocapa de vidrio de sílice (MC, o con doble capa que contiene partículas bioactivas de hidroxiapatita (HA, vidrio (V o vitrocerámico (VC, después de un periodo de 30 días. Los resultados muestran que a los 30 días de envejecimiento en medio MEM no se encuentra ningún efecto citotóxico, pero se encontró efecto genotóxico en las probetas de A y MC que no representa un peligro inminente a sistemas celulares. The stainless steel AISI 316L is the must used biomaterial for the making of temporal prosthesis, but it presents severe limitations for permanent implants due to the generation and migration of metallic ions to the surrounding peripheral tissues, which produces oxygen reactive

Avaliação da suscetibilidade à corrosão sob tensão da ZAC do aço inoxidável AISI 316L em ambiente de reator nuclear PWR Stress corrosion cracking of stainless steel AISI 316L HAZ in PWR Nuclear reactor environment

Directory of Open Access Journals (Sweden)

Mônica Maria de Abreu Mendonça Schvartzman

2009-09-01

Full Text Available Aços carbono de baixa liga e aços inoxidáveis são amplamente utilizados nos circuitos primários de reatores nucleares do tipo PWR (Pressurized Water Reactor. Ligas de níquel são empregadas na soldagem destes materiais devido a características como elevadas resistências mecânica e à corrosão, coeficiente de expansão térmica adequado, etc. Nos últimos 30 anos, a corrosão sob tensão (CST tem sido observada principalmente nas regiões das soldas entre materiais dissimilares existentes nestes reatores. Este trabalho teve como objetivo avaliar, por comparação, a suscetibilidade à corrosão sob tensão da zona afetada pelo calor (ZAC do aço inoxidável austenítico AISI 316L quando submetida a um ambiente similar ao do circuito primário de um reator nuclear PWR nas temperaturas de 303ºC e 325ºC. Para esta avaliação empregou-se o ensaio de taxa de deformação lenta - SSRT (Slow Strain Rate Test. Os resultados indicaram que a CST é ativada termicamente e que a 325ºC pode-se observar a presença mais significativa de fratura frágil decorrente do processo de corrosão sob tensão.In pressurized water reactors (PWRs, low alloy carbon steels and stainless steel are widely used in the primary water circuits. In most cases, Ni alloys are used to joint these materials and form dissimilar welds. These alloys are known to accommodate the differences in composition and thermal expansion of the two materials. Stress corrosion cracking of metals and alloys is caused by synergistic effects of environment, material condition and stress. Over the last thirty years, CST has been observed in dissimilar metal welds. This study presents a comparative work between the CST in the HAZ (Heat Affected Zone of the AISI 316L in two different temperatures (303ºC and 325ºC. The susceptibility to stress corrosion cracking was assessed using the slow strain rate tensile (SSRT test. The results of the SSRT tests indicated that CST is a thermally

48 CFR 6103.304 - Reply to the audit division and agency responses [Rule 304].

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Reply to the audit division and agency responses [Rule 304]. 6103.304 Section 6103.304 Federal Acquisition Regulations System CIVILIAN BOARD OF CONTRACT APPEALS, GENERAL SERVICES ADMINISTRATION TRANSPORTATION RATE CASES 6103.304 Reply to the audit division and agency...

Applications of the essay at slow deformation velocity in pipes of stainless steel AISI-304; Aplicaciones del ensayo a velocidad de deformacion lenta en tuberias de acero inoxidable AISI-304

Energy Technology Data Exchange (ETDEWEB)

Zamora R, L.; Mora R, T. De la [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2004-07-01

Nowadays is carried out research related with the degradation mechanisms of structures, systems and/or components in the nuclear power plants, since many of the involved processes are those responsible for the dependability of these, of the integrity of the components and of the aspects of safety. The purpose of this work, was to determine the grade of susceptibility to the corrosion of a pipe of Austenitic stainless steel AISI 304, in a solution of Na CI (3.5%) to the temperatures of 60 and 90 C, in two different thermal treatments - 1. - Sensitive 650 C by 4 hours and cooled in water. 2. Solubilized to 1050 C by 1 hour and cooled in water.

Comparative study of the microbiological corrosion among an AISI 304L and an API X65

International Nuclear Information System (INIS)

Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L.; Gonzalez F, E.

2004-01-01

Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

Effect of H{sub 2}O{sub 2} on the corrosion behavior of 304L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Song, Taek Ho

1994-02-15

In connection with the safe storage of high level nuclear waste, effect of H{sub 2}O{sub 2} on the corrosion behavior of 304L stainless steel was examined. Open circuit potentials and polarization curves were measured with and without H{sub 2}O{sub 2}. The experimental results show that H{sub 2}O{sub 2} increased corrosion potential and decreased pitting potential. The passive range, therefore, decreased as H{sub 2}O{sub 2} concentration increased, indicating that pitting resistance was decreased by the existence of H{sub 2}O{sub 2} in the electrolyte. These effects of H{sub 2}O{sub 2} on corrosion of 304L stainless steel are considered to be similar to those of γ-irradiation. To compare the effects of H{sub 2}O{sub 2} with those of O{sub 2}, cathodic and anodic polarization curves were made in three types of electrolyte such as aerated, deaerated, and stirred electrolyte. The experimental results show that the effects of H{sub 2}O{sub 2} on the corrosion behavior were very similar to those of O{sub 2} such as increase of corrosion potential, decrease of pitting resistance, and increase of repassivation potential. Further, H{sub 2}O{sub 2} played much greater role in controlling cathodic reaction rate in neutral water environment. In acid and alkaline media, potential shifts by H{sub 2}O{sub 2} were restricted by the large current density of proton reduction and by the le Chatelier's principle respectively.

Processing of fine grained AISI 304L austenitic stainless steel by cold rolling and high-temperature short-term annealing

Science.gov (United States)

Naghizadeh, Meysam; Mirzadeh, Hamed

2018-05-01

An advanced thermomechanical process based on the formation and reversion of deformation-induced martensite was used to refine the grain size and enhance the hardness of an AISI 304L austenitic stainless steel. Both low and high reversion annealing temperatures and also the repetition of the whole thermomechanical cycle were considered. While a microstructure with average austenite grain size of a few micrometers was achieved based on cold rolling and high-temperature short-term annealing, an extreme grain refinement up to submicrometer regime was obtained by cold rolling followed by low-temperature long-term annealing. However, the required annealing time was found to be much longer, which negates its appropriateness for industrial production. While a magnificent grain refinement was achieved by one pass of the high-temperature thermomechanical process, the reduction in grain size was negligible by the repetition of the whole cycle. It was found that the hardness of the thermomechanically processed material is much higher than that of the as-received material. The results of the present work were shown to be compatible with the general trend of grain size dependence of hardness for AISI 304L stainless steel based on the Hall-Petch relationship. The results were also discussed based on the X-ray evaluation of dislocation density by modified Williamson-Hall plots.

Zirconium oxide deposits (ZrO2) and titanium oxide (TiO2) on 304l stainless steel

International Nuclear Information System (INIS)

Davila N, M. L.

2015-01-01

This research project aims to carry out the surface and electrochemical characterization to obtain the optimum conditions of the hydrothermal deposits of zirconium oxide ZrO 2 (baddeleyite) and titanium oxide TiO 2 (anatase and rutile phases) on 304l stainless steel, simulating an inhibiting protective layer. 304l steel specimens were cut, pre-oxidized in water at a temperature of 288 degrees Celsius and 8 MPa, similar to those of a typical BWR conditions. From the titanium oxide anatase crystalline phase, the rutile phase was obtained by a heat treatment at 1000 degrees Celsius. The Sigma-Aldrich pre-oxidized powders and steel 304l were characterized using techniques of X-ray diffraction, scanning electron microscopy, X-ray dispersive energy, chemical mapping and Raman spectrometry. The pre-oxidized steel has two oxide layers, an inner layer with nano metric crystals and another outer of larger crystals to 1μm, with the formation of hematite and magnetite, this predominating. The surface that contacted the sample holder has larger crystals. Hydrothermal deposits were carry out from suspensions of 10, 100 and 1000 ppm, of the crystal phases of anatase, rutile and baddeleyite, on the pre-oxidized steel at a temperature of 150 degrees Celsius for 2 and 7 days, samples were analyzed by X-ray diffraction, scanning electron microscopy, X-ray dispersive energy, Raman spectrometry and Tafel polarization. The suspension to 1000 ppm for 7 days coated surface most; the baddeleyite deposit is noticed more homogeneous than anatase and rutile. The deposit is favored when hematite and magnetite crystals are larger. The chemical mapping on deposits show that even after being immersed in water to 288 degrees Celsius during 30 days, the deposits are still present although a loss is observed. A reference electrode was assembled to conduct electrochemical tests of Tafel able to withstand a temperature of 288 degrees Celsius and pressure of 8 MPa. The baddeleyite deposit presented

The effect of electrode vertex angle on automatic tungsten-inert-gas welds for stainless steel 304L plates

International Nuclear Information System (INIS)

Maarek, V.; Sharir, Y.; Stern, A.

1980-03-01

The effect of electrode vertex angle on penetration depth and weld bead width, in automatic tungsten-inert-gas (TIG) dcsp bead-on-plate welding with different currents, has been studied for stainless steel 304L plates 1.5 mm and 8 mm thick. It has been found that for thin plates, wider and deeper welds are obtained when using sharper electrodes while, for thick plates, narrower and deeper welds are produced when blunt electrodes (vertex angle 180 deg) are used. An explanation of the results, based on a literature survey, is included

26 CFR 1.304-5 - Control.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 4 2010-04-01 2010-04-01 false Control. 1.304-5 Section 1.304-5 Internal... TAXES Effects on Recipients § 1.304-5 Control. (a) Control requirement in general. Section 304(c)(1) provides that, for purposes of section 304, control means the ownership of stock possessing at least 50...

Deposition and characterization of noble metal onto surfaces of 304l stainless steel

International Nuclear Information System (INIS)

Contreras R, A.; Arganis J, C. R.; Aguilar T, J. A.; Medina A, A. L.

2010-10-01

Noble metal chemical addition (NMCA) plus hydrogen water chemistry is an industry-wide accepted approach for potential intergranular stress corrosion cracking mitigation of BWR internals components. NMCA is a method of applying noble metal onto BWR internals surfaces using reactor water as the transport medium that causes the deposition of noble metal from the liquid onto surfaces. In this work different platinum concentration solutions were deposited onto pre-oxidized surfaces of 304l steel at 180 C during 48 hr in an autoclave. In order to simulate the zinc water conditions, deposits of Zn and Pt-Zn were also carried out. The solutions used to obtain the deposits were: sodium hexahydroxyplatinate (IV), zinc nitrate hydrate and zinc oxide. The deposits obtained were characterized by scanning electron microscopy and X-ray diffraction. Finally, the electrochemical corrosion potential of pre-oxidized samples with Pt deposit were obtained and compared with the electrochemical corrosion potential of only pre-oxidized samples. (Author)

Influence of surface finish on the high cycle fatigue behavior of a 304L austenitic stainless steel

International Nuclear Information System (INIS)

Petitjean, S.

2003-06-01

This work has dealt with the influence of surface finish on the high cycle fatigue behavior of a 304L. The role played by roughness, surface hardening and residual stresses has been particularly described. First part of this study has consisted of the production of several surface finishes. These latter were obtained by turning, grinding, mechanical polishing and sandblasting. The obtained surfaces were then characterised in terms of roughness, hardening, microstructure and residual stresses. Fatigue tests were finally conducted under various stress ratios or mean stresses at two temperatures (25 C and 300 C). Results clearly evidenced an effect of the surface integrity on the fatigue resistance of the 304L. This influence is nevertheless more pronounced at ambient temperature and for a positive mean stress. For all explored testing conditions, the lowest endurance limit was obtained for ground specimens whereas polished samples exhibited the best fatigue strength. Results also cleared out a detrimental influence of a positive mean stress in the case of specimens having surface defaults of a great acuity. The study of the relative effect of each of the surface parameter, under a positive stress ratio and at the ambient temperature, showed that roughness profile and surface hardening are the two more influential factors. The role of the residual stresses remains negligible due to their rapid relaxation during the application of the first cycles of fatigue. The estimation of the initiation and propagation periods showed that mechanisms differed as a function of the applied stress ratio. Crack propagation is governed by the parameter DK at a positive stress ratio and by Dep/2 in the case of tension-compression tests. (author)

Efecto de la Composición Química del Metal de Aporte y del Calor Aportado Sobre la Microestructura y las Propiedades Mecánicas de Juntas Soldadas de Aceros Inoxidables Dúplex

Directory of Open Access Journals (Sweden)

Sebastián Zappa

Full Text Available Resumen Los aceros inoxidables dúplex poseen una microestructura dual (ferrita y austenita con contenidos aproximadamente iguales y se caracterizan por tener buena soldabilidad, buenas propiedades mecánicas y una alta resistencia a la corrosión generalizada y localizada. Gracias a estas características, estos aceros son los principales materiales a emplear en cañerías con altas exigencias, ampliamente utilizados en varias industrias, principalmente la petroquímica. Dichas propiedades están controladas por la composición química, el equilibrio microestructural y la ausencia de compuestos intermetálicos. El objetivo de este trabajo fue estudiar la influencia de la composición química del metal de aporte y el calor aportado sobre la microestructura y las propiedades mecánicas en juntas soldadas de cañerías de acero inoxidable dúplex. El metal base utilizado fue un acero inoxidable dúplex UNS S31803 de 8” de diámetro y 8,18 mm de espesor y los metales de aporte fueron dos alambres tubulares que depositan aceros inoxidables dúplex y lean dúplex (AWS A5.22: E2209T1-1 y E2209T1-G, mediante el proceso de soldadura semi-automático bajo protección gaseosa, soldados con alto y bajo calor aportado. De cada probeta se extrajeron muestras donde se determinó la composición química, se realizó la caracterización microestructural y se determinaron las propiedades mecánicas (dureza, tracción y Charpy-V.

Formação de biofilme em aço inoxidável por Aeromonas hydrophila e Staphylococcus aureus usando leite e diferentes condições de cultivo Biofilm formation by Aeromonas hydrophila and Staphylococcus aureus on stainless steel using milk and different conditions of cultivation

Directory of Open Access Journals (Sweden)

Cleube Andrade Boari

2009-12-01

Full Text Available O objetivo desta pesquisa consistiu em avaliar a formação de biofilme em aço inoxidável por Aeromonas hydrophila e Staphylococcus aureus usando leite e diferentes condições de cultivo. As variáveis em estudo consistem no cultivo monoespécie e combinado, dos referidos microrganismos e nas temperaturas de 4, 7 e 18 °C. Recipientes contendo 1000 mL de leite, densidade populacional de 10(5 UFC.mL-1 de cada microrganismo e 10 cupons de aço inoxidável (10 × 20 mm foram lacrados e armazenados, sob agitação de 60 rpm, por um período de 10 dias. As análises ocorreram a cada 48 horas. Células sésseis de A.hydrophila e S. aureus foram enumeradas através do plaqueamento seletivo em ágar m-Aeromonas selective e Baird-Parker, respectivamente. Estudos sobre o tempo de geração, enumeração de células planctônicas e observação dos cupons através da microscopia eletrônica de varredura foram conduzidos. S. aureus, em monocultivo, formou biofilme a 18 °C e a 7 °C. Para 4 °C, foi observado um processo de adesão. A presença de A. hydrophila reduziu o desempenho de S. aureus. Nesta condição de cultivo multiespécie houve formação de biofilme a 18 °C. A. hydrophila, tanto em monocultivo quanto em presença de S. aureus, formou biofilme em todas as condições pesquisadas.The aim of this research was to verify the capability of biofilm formation on stainless steel by Aeromonas hydrophila and Staphylococcus aureus using milk and different conditions of cultivation. The variables consisted in mono and multi-species cultivation of these microorganisms and in the temperatures of 4, 7 and 18 °C. Containers containing 1000 mL of milk, population density of 10(5 CFU.mL-1 of each microorganism, and ten suspended chips of stainless steel AISI 304 (10 × 20 mm were used to seal up and storage, under 60 rpm of agitation for 10 days. The analyses were conducted every 48 hours. Sessile cells of A. hydrophila and S. aureus and were enumerated

28 CFR 24.304 - Settlement.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Settlement. 24.304 Section 24.304... DEPARTMENT OF JUSTICE ADMINISTRATIVE PROCEEDINGS Procedures for Considering Applications § 24.304 Settlement. A prevailing party and Department counsel may agree on a proposed settlement of an award before...

Gas tungsten arc welding and friction stir welding of ultrafine grained AISI 304L stainless steel: Microstructural and mechanical behavior characterization

Energy Technology Data Exchange (ETDEWEB)

Sabooni, S., E-mail: s.sabooni@ma.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of); Karimzadeh, F.; Enayati, M.H. [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of); Ngan, A.H.W. [Department of Mechanical Engineering, The University of Hong Kong, Pokfulam Road, Hong Kong (China); Jabbari, H. [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of)

2015-11-15

In the present study, an ultrafine grained (UFG) AISI 304L stainless steel with the average grain size of 650 nm was successfully welded by both gas tungsten arc welding (GTAW) and friction stir welding (FSW). GTAW was applied without any filler metal. FSW was also performed at a constant rotational speed of 630 rpm and different welding speeds from 20 to 80 mm/min. Microstructural characterization was carried out by High Resolution Scanning Electron Microscopy (HRSEM) with Electron Backscattered Diffraction (EBSD) and Transmission Electron Microscopy (TEM). Nanoindentation, microhardness measurements and tensile tests were also performed to study the mechanical properties of the base metal and weldments. The results showed that the solidification mode in the GTAW welded sample is FA (ferrite–austenite) type with the microstructure consisting of an austenite matrix embedded with lath type and skeletal type ferrite. The nugget zone microstructure in the FSW welded samples consisted of equiaxed dynamically recrystallized austenite grains with some amount of elongated delta ferrite. Sigma phase precipitates were formed in the region ahead the rotating tool during the heating cycle of FSW, which were finally fragmented into nanometric particles and distributed in the weld nugget. Also there is a high possibility that the existing delta ferrite in the microstructure rapidly transforms into sigma phase particles during the short thermal cycle of FSW. These suggest that high strain and deformation during FSW can promote sigma phase formation. The final austenite grain size in the nugget zone was found to decrease with increasing Zener–Hollomon parameter, which was obtained quantitatively by measuring the peak temperature, calculating the strain rate during FSW and exact examination of hot deformation activation energy by considering the actual grain size before the occurrence of dynamic recrystallization. Mechanical properties observations showed that the welding

In situ AFM study of pitting corrosion and corrosion under strain on a 304L stainless steel

International Nuclear Information System (INIS)

Martin, F.A.; Cousty, J.; Masson, J-L.; Bataillon, C.

2004-01-01

Our study is centred on surface localised corrosion under strain of a standard stainless steel (304L). The interest we take in these corrosion phenomena is led by the general misunderstanding of its primary initiation steps. The goal of this study is to determine precisely the relationships between local geometrical defects (grain boundaries, dislocation lines, etc) or chemical defects (inclusions) with the preferential sites of corrosion on the strained material. By combining three techniques at the same time: Atomic Force Microscopy, an electrochemical cell and a traction plate, we can observe in situ the effect of localised stress and deformation on the sample surface exposed to a corrosive solution. We managed to build an original set-up compatible with all the requirements of these three different techniques. Furthermore, we prepared the surface of our sample as flat as possible to decrease at maximum the topographical noise in order to observe the smallest defect on the surface. By using a colloidal suspension of SiO 2 , we obtained surfaces with a typical corrugation (RMS) of about 1 A for areas of at least 1 μm 2 . Our experimental study has been organised in two primary investigations: - In situ study of the morphology evolution of the surface under a corrosive chloride solution (borate buffer with NaCl salt). The influence of time, NaCl concentration, and potential was investigated; - In situ exploration of a 304L strained surface. It revealed the first stages of the surface plastic evolutions like activation of sliding dislocations, materialized by parallel steps of about 2 nm high in the same grain. The secondary sliding plane systems were also noticeable for higher deformation rates. Recent results concerning in situ AFM observation of corroded surfaces under strain in a chloride media will be presented. (authors)

In situ AFM study of pitting corrosion and corrosion under strain on a 304L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Martin, F.A. [CEA de Saclay, DRECAM/SPCSI, 91191 Gif-sur-Yvette cedex (France); Cousty, J.; Masson, J-L. [CEA de Saclay, DRECAM/SPCSI, 91191 Gif-sur-Yvette cedex (France); Bataillon, C. [CEA de Saclay, DEN/DPC/LECA, 91191 Gif-sur-Yvette cedex (France)

2004-07-01

Our study is centred on surface localised corrosion under strain of a standard stainless steel (304L). The interest we take in these corrosion phenomena is led by the general misunderstanding of its primary initiation steps. The goal of this study is to determine precisely the relationships between local geometrical defects (grain boundaries, dislocation lines, etc) or chemical defects (inclusions) with the preferential sites of corrosion on the strained material. By combining three techniques at the same time: Atomic Force Microscopy, an electrochemical cell and a traction plate, we can observe in situ the effect of localised stress and deformation on the sample surface exposed to a corrosive solution. We managed to build an original set-up compatible with all the requirements of these three different techniques. Furthermore, we prepared the surface of our sample as flat as possible to decrease at maximum the topographical noise in order to observe the smallest defect on the surface. By using a colloidal suspension of SiO{sub 2}, we obtained surfaces with a typical corrugation (RMS) of about 1 A for areas of at least 1 {mu}m{sup 2}. Our experimental study has been organised in two primary investigations: - In situ study of the morphology evolution of the surface under a corrosive chloride solution (borate buffer with NaCl salt). The influence of time, NaCl concentration, and potential was investigated; - In situ exploration of a 304L strained surface. It revealed the first stages of the surface plastic evolutions like activation of sliding dislocations, materialized by parallel steps of about 2 nm high in the same grain. The secondary sliding plane systems were also noticeable for higher deformation rates. Recent results concerning in situ AFM observation of corroded surfaces under strain in a chloride media will be presented. (authors)

5 CFR 304.107 - Reports.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Reports. 304.107 Section 304.107 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS EXPERT AND CONSULTANT APPOINTMENTS § 304.107 Reports. As required by 5 U.S.C. 3109(e), each agency shall report to the Office of...

5 CFR 304.103 - Authority.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Authority. 304.103 Section 304.103... APPOINTMENTS § 304.103 Authority. (a) Basic authority. (1) When authorized by an appropriation or other statute... expert or consultant who works on a strictly intermittent basis may be appointed under this authority...

Analysis of martensitic transformation and residual tension in an 304L stainless steel; Analise da transformacao martensitica e tensao residual em um aco inoxidavel 304L

Energy Technology Data Exchange (ETDEWEB)

Alves, Juciane Maria

2014-07-01

The relationship between plastic deformation and the strain induced phase transformation, that provides a practical route to the development of new engineering materials with excellent mechanical properties, characterize the TRIP effect 'Transformation Induced Plasticity'. Among the stainless steels, the metastable 304 L austenitic steel is susceptible to transformation of austenite-martensite phase from tensile tests at room temperature by increments of plastic deformation. It is of great technological and scientific interest the knowledge of the evolution of phase transformation and residual stress from different levels and rates of plastic deformation imposed to the material. It is also important to evaluate the interference of metallographic preparation in quantitative analyzes of this steel. The main techniques used in this study consisted of X-rays diffraction and Ferritoscopy for the quantitation phase, and XRD to residual stress analysis also. As observed, the phase transformation quantification has not suffered significant influence of the metallographic preparation and evolved from increments of plastic deformation due to different stop charges and strain rates, leading to a further strengthening of the austenite matrix. The evaluation of residual stress resulting from the martensitic transformation was susceptible to the metallographic preparation and increased its value on comparison to sample without metallographic preparation. It was also observed that the residual stress decreased with the increase of the fraction of transformed martensite. (author)

21 CFR 522.304 - Carprofen.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Carprofen. 522.304 Section 522.304 Food and Drugs..., AND RELATED PRODUCTS IMPLANTATION OR INJECTABLE DOSAGE FORM NEW ANIMAL DRUGS § 522.304 Carprofen. (a) Specifications. Each milliliter of solution contains 50 milligrams (mg) carprofen. (b) Sponsor. See No. 000069 in...

Análisis de la resistencia a la corrosión de barras corrugadas de acero inoxidable en medios acuosos que simulan el hormigón

Directory of Open Access Journals (Sweden)

Belzunce, F. J.

2004-04-01

Full Text Available The corrosion behaviour of stainless steel reinforced bars used in civil engineering was studied. Different electrochemical tests were performed using several stainless steel bars (austenitic and duplex, hot and cold rolled, in the presence of a solution, which simulates the contact with salt contaminated concrete. The corrosion rates were determined and also their behaviour against localized corrosion (pitting.

Se ha realizado un estudio sobre la resistencia a la corrosión de barras corrugadas de acero inoxidable utilizadas en construcción civil para armar el hormigón. Con este objeto se han realizado diferentes ensayos electroquímicos en presencia de un medio acuoso básico, que simula el contacto con hormigón contaminado con sal, y se ha determinado la velocidad de corrosión y la resistencia a la formación de picaduras de diferentes calidades de aceros inoxidables (austeníticos y dúplex, tanto conformadas en caliente como en frío.

10 CFR 800.304 - Default.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Default. 800.304 Section 800.304 Energy DEPARTMENT OF... ASSISTANCE Loan Administration § 800.304 Default. (a) In the event that the borrower fails to perform the terms and conditions of the loan, the borrower shall be in default and the Secretary shall have the...

Establishing precursor events for stress corrosion cracking initiation in type 304L stainless steel

International Nuclear Information System (INIS)

Khan, M.U.F.; Raja, V.S.; Roychowdhury, S.; Kain, V.

2015-01-01

The present study attempts to establish slip band emergence, due to localized deformation, as a precursor event for SCC initiation in type 304L SS. The unidirectional tensile loading was used for straining flat tensile specimen, less than 10% strain, in air, 0.5 M NaCl + 0.5 M H 2 SO 4 and boiling water reactor (BWR) simulated environment (288 C. degrees, 10 MPa). The surface features were characterized using optical microscopy, scanning electron microscopy (including electron backscattered diffraction-EBSD) and atomic force microscopy. The study shows that with increase in strain level, during unidirectional slow strain rate test (SSRT), average slip band height increases in air and the attack on slip lines occurs in acidified chloride environment. In BWR simulated environment, preferential oxidation on slip lines and initiation of a few cracks on some of the slip lines are observed. Based on the observation, the study suggests slip bands, formed due to localized deformation, to act as a precursor for SCC initiation. (authors)

5 CFR 179.304 - Notification procedures.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Notification procedures. 179.304 Section 179.304 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS CLAIMS COLLECTION STANDARDS Administrative Offset § 179.304 Notification procedures. Before collecting any debt...

Desarrollo de un modelo matemático de diferencias finitas para el análisis del campo de temperaturas en la soldadura por arco de chapas finas de acero inoxidable

Directory of Open Access Journals (Sweden)

Miguel, V.

2010-12-01

Full Text Available This work develops a finite difference method to evaluate the temperature field in the heat affected zone in butt welding applied to AISI 304 stainless steel thin sheet by GTAWprocess. A computer program has been developed and implemented by Visual Basic for Applications (VBA in MS-Excel spreadsheet. The results that are obtained using the numerical application foresee the thermal behaviour of arc welding processes. An experimental methodology has been developed to validate the mathematical model that allows to measure the temperature in several points close to the weld bead. The methodology is applied to a stainless steel sheet with a thickness lower than 3 mm, although may be used for other steels and welding processes as MIG/MAG and SMAW. The data which has been obtained from the experimental procedure have been used to validate the results that have been calculated by the finite differences numerical method. The mathematical model adjustment has been carried out taking into account the experimental results. The differences found between the experimental and theoretical approaches are due to the convection and radiation heat losses, which have not been considered in the simulation model.With this simple model, the designer will be able to calculate the thermal cycles that take place in the process as well as to predict the temperature field in the proximity of the weld bead.

En este trabajo se desarrolla un método de diferencias finitas para calcular el campo de temperaturas en la zona afectada por el calor en la soldadura de dos chapas de acero inoxidable AISI 304, soldadas mediante el procedimiento GTAW. Se ha desarrollado un programa informático implementado en libros de cálculo MS-Excel con Visual Basic para Aplicaciones (VBA. Los experimentos modelizados a través de la aplicación numérica predicen el comportamiento térmico de un procedimiento de soldadura. Para la validación del modelo matemático se ha desarrollado un

Resistencia a la oxidación de aleaciones Ni-Cr-Al plaqueadas por láser sobre aceros al carbono e inoxidables austeníticos

Directory of Open Access Journals (Sweden)

de Damborenea, J.

1995-04-01

Full Text Available Laser surface cladding has been carried out by means of a 5 kW CO₂ continuous wave laser on both a mild and a stainless steel. A powder injection technique has been used to deliver a Ni-Cr-Al alloy onto the steel molten pool. After processing, samples were analyzed by optical and scanning electron microscopy in order to know the microstructure and composition of present phases. High temperature corrosion resistance tests were done in an oxidant environment at temperatures of 950 °C. Phase transformations and corrosion behaviour are discussed. A general conclusion is the suitability of these alloys to bear oxidation due to the formation of protective oxide layers on their surface.

Se realiza un estudio sobre la obtención de recubrimientos de superficie mediante un láser continuo de CO₂ de 5 kW de potencia de salida. Mediante la técnica de inyección de partículas, se realizaron plaqueados en superficie de Ni-Cr-Al sobre un acero suave y otro inoxidable de tipo 316. Tras el procesado, se estudió la microestructura de las probetas obtenidas. Posteriormente, se procedió a su ensayo en atmósfera oxidante a 950 °C, observándose la evolución de la microestructura, la formación de las capas de óxido y la cinética del proceso. Como conclusión general, destaca, independientemente de la base sobre la que se obtienen los recubrimientos, la gran resistencia del material a la oxidación, seguramente debida a la formación de capas de alúmina que actúan como barreras frente al ataque del oxidante.

Investigation of thin film deposition on stainless steel 304 substrates under different operating conditions

International Nuclear Information System (INIS)

Chowdhury, M A; Nuruzzaman, D M

2016-01-01

In recent times, friction and wear in relation to the deposited carbon films on the steel substrates are important issues for industrial applications. In this research study, solid thin films were deposited on the stainless steel 304 (SS 304) substrates under different operating conditions. In the experiments, natural gas (97.14% methane) was used as a precursor gas in a hot filament thermal chemical vapor deposition (CVD) reactor. Deposition rates on SS 304 substrates were investigated under gas flow rates 0.5 - 3.0 l/min, pressure 20 - 50 torr, gap between activation heater and substrate 3.0 - 6.0 mm and deposition duration 30 - 120 minutes. The obtained results show that there are significant effects of these parameters on the deposition rates on SS 304 within the observed range. Friction coefficient of SS 304 sliding against SS 314 was also investigated under normal loads 5 - 10 N and sliding velocities 0.5 - m/s before and after deposition. The experimental results reveal that in general, frictional values are lower after deposition than that of before deposition. (paper)

Surface decontamination of Type 304L stainless steel with electrolytically generated hydrogen: Design and operation of the electrolyzer

International Nuclear Information System (INIS)

Bellanger, G.

1993-01-01

The surface of tritiated Type 304L stainless steel is decontaminated by isotopic exchange with the hydrogen generated in an electrolyzer. This steel had previously been exposed to tritium in a tritium gas facility for several years. The electrolyzer for the decontamination uses a conducting solid polymer electrolyte made of a Nafion membrane. The cathode where the hydrogen is formed is nickel deposited on one of the polymer surfaces. This cathode is placed next to the region of the steel to be decontaminated. The decontamination involves, essentially, the tritiated oxide layers of which the initial radioactivity is ∼ 5 kBq/cm 2 . After treatment for 1 h, the decontamination factor is 8. 9 refs., 16 figs., 2 tabs

20 CFR 638.304 - Historical preservation.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Historical preservation. 638.304 Section 638.304 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR JOB CORPS PROGRAM... § 638.304 Historical preservation. The Job Corps Director shall review the “National Register of...

47 CFR 65.304 - Capital structure.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 3 2010-10-01 2010-10-01 false Capital structure. 65.304 Section 65.304... OF RETURN PRESCRIPTION PROCEDURES AND METHODOLOGIES Exchange Carriers § 65.304 Capital structure. The proportion of each cost of capital component in the capital structure is equal to: Proportion in the capital...

Evaluación de la adherencia del biofilm sobre salivaderas dentales de acero inoxidable, cerámica y opalina

OpenAIRE

Butler, Teresa Adela

2009-01-01

El objetivo principal de esta investigación fue estudiar el desarrollo de la biopelícula depositada sobre las salivaderas dentales de tres materiales diferentes (acero inoxidable, cerámica y opalina), de equipos odontológicos correspondientes a dos zonas diferentes del casco urbano de la ciudad de La Plata (Z1 y Z2). Para ello se realizaron 38 cortes de salivaderas dentales de los tres materiales, de cada zona En primer lugar se realizó el análisis de la microbiota planctónica y sé...

Dislocation structure evolution in 304L stainless steel and weld joint during cyclic plastic deformation

Energy Technology Data Exchange (ETDEWEB)

Wang, Hao; Jing, Hongyang; Zhao, Lei; Han, Yongdian; Lv, Xiaoqing [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Advanced Joining Technology, Tianjin 300072 (China); Xu, Lianyong, E-mail: xulianyong@tju.edu.cn [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Advanced Joining Technology, Tianjin 300072 (China)

2017-04-06

Dislocation structures and their evolution of 304L stainless steel and weld metal made with ER308L stainless steel welding wire subjected to uniaxial symmetric strain-controlled loading and stress-controlled ratcheting loading were observed by transmission electron microscopy (TEM). The correlation between the cyclic response and the dislocation structure has been studied. The experiment results show that the cyclic behaviour of base metal and weld metal are different. The cyclic behaviour of the base metal consists of primary hardening, slight softening and secondary hardening, while the weld metal shows a short hardening within several cycles followed by the cyclic softening behaviour. The microscopic observations indicate that in base metal, the dislocation structures evolve from low density patterns to those with higher dislocation density during both strain cycling and ratcheting deformation. However, the dislocation structures of weld metal change oppositely form initial complicated structures to simple patterns and the dislocation density gradually decrease. The dislocation evolution presented during the strain cycling and ratcheting deformation is summarized, which can qualitatively explain the cyclic behaviour and the uniaxial ratcheting behaviour of two materials. Moreover, the dislocation evolution in the two types of tests is compared, which shows that the mean stress has an effect on the rate of dislocation evolution during the cyclic loading.

Effect of martensitic transformation on springback behavior of 304L austenitic stainless steel

Science.gov (United States)

Fathi, H.; Mohammadian Semnani, H. R.; Emadoddin, E.; Sadeghi, B. Mohammad

2017-09-01

The present paper studies the effect of martensitic transformation on the springback behavior of 304L austenitic stainless steel. Martensite volume fraction was determined at the bent portion under various strain rates after bending test. Martensitic transformation has a significant effect on the springback behavior of this material. The findings of this study indicated that the amount of springback was reduced under a situation of low strain rate, while a higher amount of springback was obtained with a higher strain rate. The reason for this phenomenon is that higher work hardening occurs during the forming process with the low strain rate due to the higher martensite volume fraction, therefore the formability of the sheet is enhanced and it leads to a decreased amount of springback after the bending test. Dependency of the springback on the martensite volume fraction and strain rate was expressed as formulas from the results of the experimental tests and simulation method. Bending tests were simulated using LS-DYNA software and utilizing MAT_TRIP to determine the martensite volume fraction and strain under various strain rates. Experimental result reveals good agreement with the simulation method.

34 CFR 304.21 - Allowable costs.

Science.gov (United States)

2010-07-01

... 34 Education 2 2010-07-01 2010-07-01 false Allowable costs. 304.21 Section 304.21 Education... Grantee § 304.21 Allowable costs. In addition to the allowable costs established in the Education... allowable expenditures by projects funded under the program: (a) Cost of attendance, as defined in Title IV...

14 CFR 1203.304 - Internal effect.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Internal effect. 1203.304 Section 1203.304... Classification Principles and Considerations § 1203.304 Internal effect. The effect of security protection on... effects and added costs inherent in a security classification must be assessed in light of the detrimental...

24 CFR 291.304 - Bidding process.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Bidding process. 291.304 Section 291.304 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued... Family Mortgage Loans § 291.304 Bidding process. (a) Submission of bids. All bids must be submitted to...

34 CFR 685.304 - Counseling borrowers.

Science.gov (United States)

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false Counseling borrowers. 685.304 Section 685.304 Education... Direct Loan Program Schools § 685.304 Counseling borrowers. (a) Entrance counseling. (1) Except as provided in paragraph (a)(8) of this section, a school must ensure that entrance counseling is conducted...

20 CFR 801.304 - Business hours.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Business hours. 801.304 Section 801.304 Employees' Benefits BENEFITS REVIEW BOARD, DEPARTMENT OF LABOR ESTABLISHMENT AND OPERATION OF THE BOARD Action by the Board § 801.304 Business hours. The office of the Clerk of the Board at Washington, DC...

Effect of pre-hardening on the lifetime of type 304L austenitic stainless steels

International Nuclear Information System (INIS)

Kpodekon, C.

2010-01-01

This study deals with the effect of the loading history on the cyclic behavior and the fatigue life of two kinds (THYSSEN and CLI) of 304L stainless steel at room temperature. The experiments have been performed using two specimens' categories. The first one (virgin) has been submitted to only classical fatigue tests while in the second category, prior to the fatigue test, the specimen is subjected to a pre-hardening process under either monotonic or cyclic strain control. Cyclic softening followed by cyclic hardening are observed for the virgin specimens while only cyclic softening is exhibited by the pre-hardened specimens. The obtained results show that fatigue life is strongly influenced by the pre-hardening: it seems beneficial under stress control but detrimental under strain control, even in the presence of a compressive mean stress. The results are discussed regarding the cyclic evolution of the elastic modulus as well as the isotropic and kinematic parts of the strain hardening, and strain energy density per cycle, in different configurations: with or without prehardening,stress or strain control. (author)

Oxidación en vapor de agua del acero inoxidable aisi 317 a 700 y 750ºc

OpenAIRE

MARULANDA AREVALO, JOSE LUDDEY; REMOLINA MILLAN, ADULJAY; BARON, JAIRO ALBERO

2013-01-01

Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

OXIDACIÓN EN VAPOR DE AGUA DEL ACERO INOXIDABLE AISI 317 A 700 Y 750ºC

OpenAIRE

José Luddey Marulanda Arevalo; Aduljay Remolina Millan; Jairo Alberto Barón

2013-01-01

Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

Electrochemical Study of Welded AISI 304 and 904L Stainless Steel in Seawater in View of Corrosion

Directory of Open Access Journals (Sweden)

Richárd Székely

2010-10-01

Full Text Available This is a comparative study of the corrosion behaviour of welds in AISI 304 and AISI 904L stainless steels carried out in seawater model solution in the temperature range 5-35°C and the standard of corrosion testing of welds was followed. The corrosion rate and corrosion attack characteristics were determined for welds of the examined steels with several type of treatment. The aim of this work was to compare the steels based on their resistance against the corrosion in terms of pitting potential (Epit and repassivation potential (Erepass. Seawater is an electrochemically aggressive medium, which can initiate localised corrosion in welded stainless steels. Different electrochemical and testing methods were used, including cyclic voltammetry, chronopotentiometry, electrochemical impedance spectroscopy (EIS, pH measuring and penetration tests.

Tests on mechanical behavior of 304 L stainless steel under constant stress associated with cyclic strain

International Nuclear Information System (INIS)

Lebey, J.; Roche, R.

1979-01-01

Mechanical analyses of structures, to be efficient, must incorporate materials behavior data. Among the mechanisms liable to cause collapse, progressive distortion (or ratcheting) has been the subject of only a few basic experiments, most of the investigations being theoretical. In order to get meaningful results to characterize materials behavior, an experimental study on ratcheting of austenitic steels has been undertaken at the C.E.A. This paper gives the first results of tests at room temperature on thin tubes of 304L steel submitted to an axial constant stress (primary stress) to which is added a cyclic shearing strain (secondary stress). The tests cover a large combination of the two loading modes. The main results consist of curves of cumulative iso-deformation in the primary and secondary stress field (Bree type diagrams). Results are given for plastic deformations ranging from 0.1 to 2.5% up to N=100 cycles

Comportamiento al desgaste por deslizamiento en aceros inoxidables: ferrítico, austenítico, dúplex y martensítico.

OpenAIRE

Renedo Rouco, Jordi

2010-01-01

En este proyecto se estudia el comportamiento al desgaste por deslizamiento de cuatro aceros representativos de las cuatro grandes familias de aceros inoxidables: ferrítico (AISI 446), austenítico (AISI 316), dúplex (AISI 2205) y martensítico (AISI 420). Para cada uno de ellos se han realizado: caracterización metalográfica, determinación de dureza, densidad y rugosidad, y ensayos de tribología mediante la técnica de bola sobre disco. Esta técnica consiste en deslizar una bola ...

Low cycle fatigue: high cycle fatigue damage accumulation in a 304L austenitic stainless steel; Endommagement et cumul de dommage en fatigue dans le domaine de l'endurance limitee d'un acier inoxydable austenitique 304L

Energy Technology Data Exchange (ETDEWEB)

Lehericy, Y

2007-05-15

The aim of this study was to evaluate the consequences of a Low Cycle Fatigue pre-damage on the subsequent fatigue limit of a 304L stainless steel. The effects of hardening and severe roughness (grinding) have also been investigated. In a first set of tests, the evolution of the surface damage induced by the different LCF pre-cycling was characterized. This has permitted to identify mechanisms and kinetics of damage in the plastic domain for different surface conditions. Then, pre-damaged samples were tested in the High Cycle Fatigue domain in order to establish the fatigue limits associated with each level of pre-damage. Results evidence that, in the case of polished samples, an important number of cycles is required to initiate surface cracks ant then to affect the fatigue limit of the material but, in the case of ground samples, a few number of cycles is sufficient to initiate cracks and to critically decrease the fatigue limit. The fatigue limit of pre-damaged samples can be estimated using the stress intensity factor threshold. Moreover, this detrimental effect of severe surface conditions is enhanced when fatigue tests are performed under a positive mean stress (author)

28 CFR 301.304 - Representation of claimant.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Representation of claimant. 301.304 Section 301.304 Judicial Administration FEDERAL PRISON INDUSTRIES, INC., DEPARTMENT OF JUSTICE INMATE ACCIDENT COMPENSATION Compensation for Work-Related Physical Impairment or Death § 301.304 Representation...

Multi-Wavelength Variability in PKS 2155-304 Y. G. Zheng1,2, L ...

Indian Academy of Sciences (India)

2009), we attempt to model the multi-wavelength variability in PKS 2155-304. We assume that the acceleration process is a stochastic process and we describe it as the diffusion of the particle momentum. Throughout the paper, we assume the. Hubble constant H0 = 70 km s−1. Mpc. −1. , the matter energy density M = 0.27,.

AES depth profiles in Mo-coated 304L stainless steel achieved by RF-magnetron sputtering and influence of Mo on the corrosion in 3.5% NaCl solution

Energy Technology Data Exchange (ETDEWEB)

Saidi, D. [Département de métallurgie, Division de Technologie du Combustible, Centre de Recherche Nucléaire de Draria CRND, BP. 43 Draria, Alger (Algeria); Zaid, B., E-mail: zaidbachir@yahoo.com [Département de métallurgie, Division de Technologie du Combustible, Centre de Recherche Nucléaire de Draria CRND, BP. 43 Draria, Alger (Algeria); Souami, N. [Centre de Recherche Nucléaire d’Alger CRNA, 2 Bd. Frantz Fanon, Alger (Algeria); Saoula, N. [Division des Milieux Ionisés et Lasers, Centre de Développement des Technologies Avancées CDTA, Cité du 20 août 1956, Baba Hassan, BP n 17, Alger (Algeria); Siad, M. [Centre de Recherche Nucléaire d’Alger CRNA, 2 Bd. Frantz Fanon, Alger (Algeria); Si Ahmed, A. [Im2np, UMR 7334 CNRS, Aix-Marseille Université, 13397 Marseille Cedex 20 (France); Biberian, J.P. [CINaM, UMR 7525 CNRS, Aix Marseille Université, 13288 Marseille Cedex 9 (France)

2015-10-05

Highlights: • Mo coating of 304L stainless steel is achieved via RF-magnetron sputtering. • The AES depth profiles before and after annealing in air (at 973 K) are analyzed. • The corrosions in NaCl solution of bare and Mo-coated samples are compared. • Mo-coated steels exhibit better corrosion behaviors. • The positive action of Mo oxide via its semi-conducting properties is deduced. - Abstract: Molybdenum-coated 304L stainless steel samples, fabricated by RF-magnetron sputtering, are characterized by Auger Electron Spectroscopy (AES) before and after annealing in air at 973 K. The electrochemical parameters of bare and coated materials, in NaCl 3.5% water solution at 298 K, are derived from the potentiodynamic polarization curves. The corrosion current of Mo-coated samples (before and after annealing) is significantly lower than that of its bare counterpart. The information gained from the AES depth profiles leads us to infer that the positive action of molybdenum on the corrosion behavior may be attributed to the changes induced by the semi-conducting properties of Mo oxide in the passive film.

48 CFR 9901.304 - Membership.

Science.gov (United States)

2010-10-01

... Administrator. (d) An individual who is particularly knowledgeable about cost accounting problems and systems... Section 9901.304 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET ADMINISTRATION RULES AND PROCEDURES 9901.304 Membership...

41 CFR 105-54.304 - Cost guidelines.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Cost guidelines. 105-54.304 Section 105-54.304 Public Contracts and Property Management Federal Property Management... Administration 54-ADVISORY COMMITTEE MANAGEMENT 54.3-Advisory Committee Procedures § 105-54.304 Cost guidelines...

Solid state crack repair by friction stir processing in 304L stainless steel

Institute of Scientific and Technical Information of China (English)

C.Gunter; M.P.Miles; F.C.Liu; T.W Nelson

2018-01-01

Friction stir processing (FSP) was investigated as a method of repairing cracks in 12mm thick 304L stainless steel plate.Healing feasibility was demonstrated by processing a tapered crack using a PCBN/WRe tool with a 25 mm diameter shoulder and a pin length of 6.4 mm.The experiment showed that it was possible to heal a crack that begins narrow and then progressively grows up to a width of 2 mm.Bead on plate experiments were used to find the best parameters for creating a consolidated stir zone with the least amount of hardness difference compared to the base metal.Grain refinement in some specimens resulted in much higher stir zone hardness,compared to base metal.A plot of grain size versus microhardness showed a very strong inverse correlation between grain size and hardness,as expected from the HallPetch relationship.Corrosion testing was carried out in order to evaluate the effect of FSP on potential sensitization of the stir zone.After 1000h of intermittent immersion in 3.5％ saline solution at room temperature it was found that no corrosion products formed on the base material controls or on any of the friction stir processed specimens.

Crack propagation in stainless steel AISI 304L in Hydrogen Chemistry conditions (HWC)

International Nuclear Information System (INIS)

Diaz S, A.; Fuentes C, P.; Merino C, F.; Castano M, V.

2006-01-01

Velocities of crack growth in samples type CT pre cracking of stainless steel AISI 304l solder and sensitized thermally its were obtained by the Rising Displacement method or of growing displacement. It was used a recirculation circuit that simulates the operation conditions of a BWR type reactor (temperature of 280 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu + ion. In each essay stayed a displacement velocity was constant of 1x10 -9 m/s, making a continuous pursuit of the advance of the crack by the electric potential drop technique. Contrary to the idea of mitigation of the crack propagation velocity by effect of the addition of the hydrogen in the system, the values of the growth velocities obtained by this methodology went similar to the opposing ones under normal operation conditions. To the finish of the rehearsal one carries out the fractographic analysis of the propagation surfaces, which showed cracks growth in trans and intergranular way, evidencing the complexity of the regulator mechanisms of the IGSCC like in mitigation conditions as the alternative Hydrogen Chemistry. (Author)

5 CFR 9901.304 - Definitions.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Definitions. 9901.304 Section 9901.304 Administrative Personnel DEPARTMENT OF DEFENSE HUMAN RESOURCES MANAGEMENT AND LABOR RELATIONS SYSTEMS (DEPARTMENT... supplement established to address recruitment or retention difficulties or for other appropriate reasons and...

48 CFR 9.304 - Exceptions.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Exceptions. 9.304 Section... CONTRACTOR QUALIFICATIONS First Article Testing and Approval 9.304 Exceptions. Normally, testing and approval is not required in contracts for— (a) Research or development; (b) Products requiring qualification...

Ductility in a new low nickel stainless steel for reinforced concrete

Directory of Open Access Journals (Sweden)

Cobo, A.

2011-12-01

Full Text Available This paper discusses the stress-strain curves for a new low nickel stainless steel, a conventional AISI 304 stainless steel and a carbon steel commonly used in reinforced concrete structures. Ductility was studied in terms of ultimate tensile strength (f_max, elastic limit (f_y and total elongation at maximum force [ultimate strain; uniform elongation] (ε_max. The three materials were assessed with internationally accepted criteria, such as plastic rotational capacity, necking region and the toughness index (total energy absorbed at uniform elongation. The findings were compared to the properties of three types of conventional reinforcing steel: 500SD, 500N and 500H (EC-2.

En este trabajo se presentan los diagramas tensióndeformación de un nuevo acero inoxidable con bajo contenido en níquel, un inoxidable convencional AISI 304 y un acero al carbono de uso común en estructuras de hormigón armado. Dicha ductilidad se ha estudiado determinando la tensión máxima (f_max, la tensión en el límite elástico (f_y y la deformación bajo carga máxima (ε_max. Los tres materiales se han evaluado utilizando criterios aceptados internacionalmente, como son el índice p (capacidad de rotación plástica, el índice A* (área plástica de endurecimiento y el índice de tenacidad I_d (energía total absorbida en el punto de alargamiento bajo carga máxima, los resultados obtenidos se han comparado con los aceros convencionales de armaduras 500SD, 500N y 500H (EC-2.

304 Concretion Facility Closure Plan

International Nuclear Information System (INIS)

1991-10-01

The Hanford Site, located northwest of Richland, Washington, houses reactors, chemical-separation systems, and related facilities used for the production of special nuclear materials. The 300 Area of the Hanford Site contains reactor fuel manufacturing facilities and several research and development laboratories. Recyclable scrap uranium with Zircaloy-2 and copper silicon allo , uranium-titanium alloy, beryllium/Zircaloy-2 alloy, and Zircaloy-2 chips and fines were secured in concrete billets (7.5-gal containers) in the 304 Concretion Facility (304 Facility), located in the 300 Area. The beryllium/Zircaloy-2 alloy and Zircaloy-2 chips and fines are designated as low-level radioactive mixed waste (LLRMW) with the characteristic of ignitability. The concretion process reduced the ignitability of the fines and chips for safe storage and shipment. This process has been discontinued and the 304 Concretion Facility is now undergoing closure as defined in the Resource Conservation and Recovery Act of 1976 (RCRA) and the Washington Administrative Code (WAC) Dangerous Waste Regulations, WAC 173-303-040 (Ecology 1991). This closure plan presents a description of the facility, the history of materials and wastes managed, and the procedures that will be followed to close the 304 Facility. The strategy for closure of the 304 Facility is presented in Section 6.0

304 Concretion facility closure plan

International Nuclear Information System (INIS)

1990-04-01

The Hanford Site, located northwest of Richland, Washington, houses reactors, chemical-separation systems, and related facilities used for the production of special nuclear materials. The 300 Area of the Hanford Site contains reactor fuel manufacturing facilities and several research and development laboratories. Recyclable scrap uranium Zircaloy-2 and copper silicon alloy, uranium-titanium alloy, beryllium/Zircaloy-2 alloy, and Zircaloy-2 chips and fines were secured in concrete billets in the 304 Concretion Facility, located in the 300 Area. The beryllium/Zircaloy-2 alloy and Zircaloy-2 chips and fines are designated as low-level radioactive mixed waste (LLRMW) with the characteristic of ignitability. The concretion process reduced the ignitability of the fines and chips for safe storage and shipment. This process has been discontinued and the 304 Concretion Facility is now undergoing closure as defined in the Resource Conservation and Recovery Act of 1976 (RCRA). This closure plan presents a description of the facility, the history of materials and wastes managed, and the procedures that will be followed to close the 304 Concretion Facility (304 Facility). Clean closure of the 304 Facility is the proposed method for closure of the facility. Justification for this proposal is presented. 15 refs., 22 figs., 4 tabs

Some aspects of thermomechanical fatigue of AISI 304L stainless steel: Part I. creep- fatigue damage

Science.gov (United States)

Zauter, R.; Christ, H. J.; Mughrabi, H.

1994-02-01

Thermomechanical fatigue (TMF) tests on the austenitic stainless steel AISI 304L have been conducted under “true≓ plastic-strain control in vacuum. This report considers the damage oc-curring during TMF loading. It is shown how the temperature interval and the phasing (in-phase, out-of-phase) determine the mechanical response and the lifetime of the specimens. If creep-fatigue interaction takes place during in-phase cycling, the damage occurs inside the ma-terial, leading to intergranular cracks which reduce the lifetime considerably. Out-of-phase cy-cling inhibits creep-induced damage, and no lifetime reduction occurs, even if the material is exposed periodically to temperatures in the creep regime. A formula is proposed which allows prediction of the failure mode, depending on whether creep-fatigue damage occurs or not. At a given strain rate, the formula is able to estimate the temperature of transition between pure fatigue and creep-fatigue damage.

Fatigue behaviour of 304L steel welded structures: influence of residual stresses and surface mechanical finishing

International Nuclear Information System (INIS)

Magnier-Monin, L.

2007-12-01

This study focuses on the influence of residual stresses and surface mechanical finishing on lifetime of stainless steel 304L welded structures. Residual stresses are determined on specific specimens of three types: base-metal, as-welded and ground-welded specimens. Each type is submitted to fatigue tests in order to assess the influence of these parameters on the lifetime, and to determine their evolution. The experiments show that an important surface stress concentration is located in the weld root of as-welded structures, which has a negative effect on the fatigue life. The grinding operation generates high-level surface residual stresses but the lifetime is higher thanks to the reduction of the notch effect. The fatigue test results are compared to the nuclear industry best-fit S-N curves. This enables the determination of correction factors related to fatigue test results of polished specimens, and to assess the lifetime of structures. (author)

Influence of low-temperature nitriding on the strain-induced martensite and laser-quenched austenite in a magnetic encoder made from 304L stainless steel

Science.gov (United States)

Leskovšek, Vojteh; Godec, Matjaž; Kogej, Peter

2016-01-01

We have investigated the possibility of producing a magnetic encoder by an innovative process. Instead of turning grooves in the encoder bar for precise positioning, we incorporated the information in 304L stainless steel by transforming the austenite to martensite after bar extrusion in liquid nitrogen and marking it with a laser, which caused a local transformation of martensite back into austenite. 304L has an excellent corrosion resistance, but a low hardness and poor wear resistance, which limits its range of applications. However, nitriding is a very promising way to enhance the mechanical and magnetic properties. After low-temperature nitriding at 400 °C it is clear that both ε- and α′-martensite are present in the deformed microstructure, indicating the simultaneous stress-induced and strain-induced transformations of the austenite. The effects of a laser surface treatment and the consequent appearance of a non-magnetic phase due to the α′ → γ transformation were investigated. The EDS maps show a high concentration of nitrogen in the alternating hard surface layers of γN and α′N (expanded austenite and martensite), but no significantly higher concentration of chromium or iron was detected. The high surface hardness of this nitride layer will lead to steels and encoders with better wear and corrosion resistance. PMID:27492862

Comparative study in the induced corrosion by sulfate reducing microorganisms, in a stainless steel 304L sensitized and a carbon steel API X65

International Nuclear Information System (INIS)

Diaz S, A.; Gonzalez F, E.; Arganis J, C.; Luna C, P.; Carapia M, L.

2004-01-01

In spite of the operational experience related with the presence of the phenomenon of microbiological corrosion (MIC) in industrial components, it was not but until the decade of the 80 s when the nuclear industry recognized its influence in some systems of Nuclear Generating Power plants. At the moment, diverse studies that have tried to explain the generation mechanism of this phenomenon exist; however, they are even important queries that to solve, especially those related with the particularities of the affected metallic substrates. Presently work, the electrochemical behavior of samples of stainless steel AISI 304L sensitized is evaluated and the carbon steel APIX65, before the action of sulfate reducing microorganisms low the same experimental conditions; found that for the APIX65 the presence of this type of bacteria promoted the formation of a stable biofilm that allowed the maintenance of the microorganisms that damaged the material in isolated places where stings were generated; while in the AISI 304L, it was not detected damage associated to the inoculated media. The techniques of Resistance to the Polarization and Tafel Extrapolation, allowed the calculation of the speed of uniform corrosion, parameter that doesn't seem to be influenced by the presence of the microorganisms; while that noise electrochemical it distinguished in real time, the effect of the sulfate reducing in the steel APIX65. (Author)

Efecto de la velocidad y ángulo de impacto en la resistencia a corrosión - erosión de aceros inoxidables recubiertos con TiN

Directory of Open Access Journals (Sweden)

José Ricardo Cano Rodas

2004-01-01

Full Text Available Fueron estudiados los mecanismos de degradación superficial en aceros inoxidables austenítico AISI 304 y martensítico AISI 420, con y sin recubrimiento cerámico de TiN, aplicado mediante técnica de deposición física de vapor PVD por arco pulsado, sometidos a erosión (solución de agua destilada con 30% en peso de partículas de sílice, corrosión (solución ½ M H2SO4 + 3.5% NaCl y efectos sinérgicos corrosión - erosión. Fue construido un dispositivo para realizar los ensayos descritos con la posibilidad de variar la velocidad y el ángulo medio de impacto de las partículas sobre la superficie de las muestras. Marcas características fueron observadas en las superficies desgastadas, siendo la condición de ángulo rasante la de mayor efecto nocivo tanto para las superficies desnudas como para las recubiertas con TiN. El nivel de deterioro superficial aumentó con la velocidad de impacto, al tiempo que se evidenció la importancia de la adherencia de las películas protectoras al substrato para la obtención de una buena resistencia a corrosiónerosión. La sinergia corrosión-erosión presentó, en algunas ocasiones, un efecto positivo para la superficie, ya que el impacto de las partículas duras causó intensa deformación plástica pero no consiguió remover material de la superficie.

Oligo-cyclic damage and behaviour of a 304 L austenitic stainless steel according to environment (vacuum, air, PWR primary water) at 300 C

International Nuclear Information System (INIS)

De Baglion, L.

2011-01-01

Nowadays, for nuclear power plants licensing or operating life extensions, various safety authorities require the consideration of the primary water environment effect on the fatigue life of Pressurized Water Reactor (PWR) components. Thus, this work focused on the study of low cycle fatigue damage kinetics and mechanisms, of a type 304L austenitic stainless steel. Several parameters effects such as temperature, strain rate or strain amplitude were investigated in air as in PWR water. Thanks to targeted in-vacuum tests, the intrinsic influence of these parameters and environments on the fatigue behaviour of the material was studied. It appears that compared with vacuum, air is already an active environment which is responsible for a strong decrease in fatigue lifetime of this steel, especially at 300 C and low strain amplitude. The PWR water coolant environment is more active than air and leads to increased damage kinetics, without any modifications of the initiation sites or propagation modes. Moreover, the decreased fatigue life in PWR water is essentially attributed to an enhancement of both initiation and micropropagation of 'short cracks'. Finally, the deleterious influence of low strain rates on the 304L austenitic stainless steel fatigue lifetime was observed in PWR water environment, in air and also in vacuum without any environmental effects. This intrinsic strain rate effect is attributed to the occurrence of the Dynamic Strain Aging phenomenon which is responsible for a change in deformation modes and for an enhancement of cracks initiation. (author)

12 CFR 304.3 - Reports.

Science.gov (United States)

2010-01-01

... assessments and monitor the condition, performance, and risk profile of individual banks and the banking... insured branches and the banking industry. Insured branches must also submit annually such information on... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Reports. 304.3 Section 304.3 Banks and Banking...

Influence of Size on the Microstructure and Mechanical Properties of an AISI 304L Stainless Steel—A Comparison between Bulk and Fibers

Directory of Open Access Journals (Sweden)

Francisco J. Baldenebro-Lopez

2015-01-01

Full Text Available In this work, the mechanical properties and microstructural features of an AISI 304L stainless steel in two presentations, bulk and fibers, were systematically studied in order to establish the relationship among microstructure, mechanical properties, manufacturing process and effect on sample size. The microstructure was analyzed by XRD, SEM and TEM techniques. The strength, Young’s modulus and elongation of the samples were determined by tensile tests, while the hardness was measured by Vickers microhardness and nanoindentation tests. The materials have been observed to possess different mechanical and microstructural properties, which are compared and discussed.

Estudio comparativo de la cavidad de acceso radicular en conductos curvos con limas de níquel-titanio y taladros de acero inoxidable

OpenAIRE

Oncins Rodríguez, J.; Pumarola Suñé, José; Canalda Sahli, Carlos

2005-01-01

El propósito de este estudio fue comparar la cantidad de dentina radicular removida y evaluar el mantenimiento de la forma del conducto tras la instrumentación de los dos tercios coronarios radiculares, utilizando instrumentos de acero inoxidable (taladros de Gates Glidden) y de níqueltitanio (limas GT Flare y limas Orifice Shaper). Un total de 42 dientes humanos extraídos con conductos radiculares curvos fueron divididos en tres grupos. Los conductos se instrumentaron mecánicamente usando ta...

Corrosion testing of a degraded moderator: L-Area Tuff Tanks

International Nuclear Information System (INIS)

Mickalonis, J.I.

2000-01-01

Based on test results, storage of the degraded moderator in 55-gallon 304L drums (0.065 inches thick) would not cause failure by general corrosion for up to 5 plus years storage. Acidic degraded moderator was temporarily stored in Tuff Tanks located in L-area. The moderator characteristics included a D 2 O content of 5.02--5.33%, a pH of 1.25--1.31, a conductivity of 29,300--31,200 m mhos/cm, tritium activity of 114--141 m Ci/mL, and levels of approximately 6,000 ppm for chloride and 500 ppm for chromium. The compatibility of the degraded with AISI Type 304L stainless steel (304L) was investigated in this study. Following ASTM standard practice, coupon immersion tests were conducted in both treated and untreated moderator. Treatment included the addition of either a 40 wt % NaOH solution, distilled water to serially dilute the chloride, or concentrated nitric acid to increase the nitrate concentration. Type 304L stainless steel exposed to the Tuff Tank moderator was found from these tests to: have a general corrosion rate of less than 5 mils per year (mpy) for 304L plate, which bounds that of the 304L storage drum, passivate at chloride concentrations up to 5,000 ppm for 304L sheet, resist corrosion for nitrate/chloride ratios ranging from 0.1 to 1,000, and be susceptible to crevice corrosion. Based on these test results, storage of the degraded moderator in 55-gallon 304L drums (0.065 inch thick) would not cause failure by general corrosion for up to 5+ years storage. The chloride concentration, [Cl], in the degraded moderator has been measured up to 6000 ppm. The potential or risk for aggressive localized attack of 304L increases with [Cl] concentration. A qualitative range is as follows: [Cl minus ] minus ] minus ] < 600 ppm, reasonable resistance, medium risk. The degraded moderator should be treated to reduce the chloride concentration to reduce the potential for localized corrosion and the risk for a leakage failure of the drum. A good practice would be to

DISEÑO DE UN PROTOTIPO FERMENTADOR DE LECHE SEMIAUTOMÁTICO PARA LA ELABORACIÓN DE SUERO COSTEÑO

Directory of Open Access Journals (Sweden)

BASHIR YACUB B.

Full Text Available El Suero Costeño es un producto lácteo fermentado, artesanalmente en la costa atlántica colombiana. Para cumplir con las normas sanitarias el fermentador está constituido por un tanque diseñado y fabricado en acero inoxidable 304, con un volumen neto de 30 L. Se garantizó una temperatura de 35°C en la fermentación de la leche, con un sistema de enfriamiento mediante una chaqueta. La temperatura se medió con un sensor de temperatura, tipo PT-100, con el sistema microcontrolado se programó su set-point, para separar el espiche del suero se utilizó una válvula; la finalización de la fermentación se determinó con la medición del pH con un pH-metro. La cantidad de materia prima y producto se mide con un sensor de nivel y se muestra de manera continua en la pantalla LCD del panel de control.

48 CFR 47.304 - Determination of delivery terms.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Determination of delivery terms. 47.304 Section 47.304 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT TRANSPORTATION Transportation in Supply Contracts 47.304 Determination of delivery...

Correlation of radiation-induced changes in microstructure/microchemistry, density and thermo-electric power of type 304L and 316 stainless steels irradiated in the Phénix reactor

Energy Technology Data Exchange (ETDEWEB)

Renault Laborne, Alexandra, E-mail: alexandra.renault@cea.fr [CEA, DEN, SRMA, F-91191 Gif-sur-Yvette (France); Gavoille, Pierre [CEA, DEN, SEMI, F-91191 Gif-sur-Yvette (France); Malaplate, Joël [CEA, DEN, SRMA, F-91191 Gif-sur-Yvette (France); Pokor, Cédric [EDF R& D, MMC, Site des Renardières, F-77818 Morêt-sur-Loing cedex (France); Tanguy, Benoît [CEA, DEN, SEMI, F-91191 Gif-sur-Yvette (France)

2015-05-15

Annealed specimens of type 304L and 316 stainless steel and cold-worked 316 specimens were irradiated in the Phénix reactor in the temperature range 381–394 °C and to different damage doses up to 39 dpa. The microstructure and microchemistry of both 304L and 316 have been examined using the combination of the different techniques of TEM to establish the void swelling and precipitation behavior under neutron irradiation. TEM observations are compared with results of measurements of immersion density and thermo-electric power obtained on the same irradiated stainless steels. The similarities and differences in their behavior on different scales are used to understand the factors in terms of the chemical composition and metallurgical state of steels, affecting the precipitation under irradiation and the swelling behavior. Irradiation induces the formation of some precipitate phases (e.g., M{sub 6}C and M{sub 23}C{sub 6}-type carbides, and γ’- and G-phases), Frank loops and cavities. According to the metallurgical state and chemical composition of the steel, the amount of each type of radiation-induced defects is not the same, affecting their density and thermo-electric power.

Correlation of radiation-induced changes in microstructure/microchemistry, density and thermo-electric power of type 304L and 316 stainless steels irradiated in the Phénix reactor

Science.gov (United States)

Renault Laborne, Alexandra; Gavoille, Pierre; Malaplate, Joël; Pokor, Cédric; Tanguy, Benoît

2015-05-01

Annealed specimens of type 304L and 316 stainless steel and cold-worked 316 specimens were irradiated in the Phénix reactor in the temperature range 381-394 °C and to different damage doses up to 39 dpa. The microstructure and microchemistry of both 304L and 316 have been examined using the combination of the different techniques of TEM to establish the void swelling and precipitation behavior under neutron irradiation. TEM observations are compared with results of measurements of immersion density and thermo-electric power obtained on the same irradiated stainless steels. The similarities and differences in their behavior on different scales are used to understand the factors in terms of the chemical composition and metallurgical state of steels, affecting the precipitation under irradiation and the swelling behavior. Irradiation induces the formation of some precipitate phases (e.g., M6C and M23C6-type carbides, and γ'- and G-phases), Frank loops and cavities. According to the metallurgical state and chemical composition of the steel, the amount of each type of radiation-induced defects is not the same, affecting their density and thermo-electric power.

Correlation of radiation-induced changes in microstructure/microchemistry, density and thermo-electric power of type 304L and 316 stainless steels irradiated in the Phénix reactor

International Nuclear Information System (INIS)

Renault Laborne, Alexandra; Gavoille, Pierre; Malaplate, Joël; Pokor, Cédric; Tanguy, Benoît

2015-01-01

Annealed specimens of type 304L and 316 stainless steel and cold-worked 316 specimens were irradiated in the Phénix reactor in the temperature range 381–394 °C and to different damage doses up to 39 dpa. The microstructure and microchemistry of both 304L and 316 have been examined using the combination of the different techniques of TEM to establish the void swelling and precipitation behavior under neutron irradiation. TEM observations are compared with results of measurements of immersion density and thermo-electric power obtained on the same irradiated stainless steels. The similarities and differences in their behavior on different scales are used to understand the factors in terms of the chemical composition and metallurgical state of steels, affecting the precipitation under irradiation and the swelling behavior. Irradiation induces the formation of some precipitate phases (e.g., M 6 C and M 23 C 6 -type carbides, and γ’- and G-phases), Frank loops and cavities. According to the metallurgical state and chemical composition of the steel, the amount of each type of radiation-induced defects is not the same, affecting their density and thermo-electric power

A comparison of tensile, fracture and fatigue mechanical behaviour of structural reinforcing bars made with different steels

Directory of Open Access Journals (Sweden)

Rodríguez, C.

2013-09-01

Full Text Available The use of austenitic stainless steels as rebar is an option increasingly used in reinforced concrete structures exposed to aggressive environments and especially those that have to work in marine environments. The same is true for duplex stainless steel rebars, although nowadays they have a lower use, mainly due to the fact that their inclusion in the reinforced concrete standards was delayed 10 years compared to austenitic stainless steel ones, and consequently their in-service behavior is not as well known. A study of the mechanical properties, including fracture toughness, fatigue behaviour and corrosion resistance in saline alkaline environments of austenitic (AISI 304LN and 316LN and duplex (D2205 stainless steel reinforcing bars was performed in this work. Bars made on a high ductility carbon steel (B500SD that are normally used to reinforce concrete were also characterized and used as a comparison. Stainless steel reinforcing bars show mechanical properties at least similar but usually higher than one of the best carbon steel re-bars (B500SD, along with a significantly higher ductility and, of course, much better corrosion behaviour in saline alkaline environments.El uso de aceros inoxidables austeníticos como armaduras de refuerzo es una opción cada vez más utilizada en estructuras de hormigón armado expuestas a ambientes agresivos y especialmente en las que han de trabajar en ambientes marinos. Lo mismo cabe decir de las armaduras de acero inoxidable dúplex, si bien su uso es menor, debido sobre todo a que su inclusión en la normativa aplicable al armado de hormigón se retrasó 10 años con respecto a los inoxidables austeníticos y, consecuentemente, su comportamiento en servicio es menos conocido. En este trabajo se analiza el comportamiento mecánico, incluyendo fractura y fatiga, así como la resistencia a la corrosión en medios que simulan un hormigón contaminado de cloruros, de armaduras fabricadas tanto con

Analysis of martensitic transformation and residual tension in an 304L stainless steel

International Nuclear Information System (INIS)

Alves, Juciane Maria

2014-01-01

The relationship between plastic deformation and the strain induced phase transformation, that provides a practical route to the development of new engineering materials with excellent mechanical properties, characterize the TRIP effect 'Transformation Induced Plasticity'. Among the stainless steels, the metastable 304 L austenitic steel is susceptible to transformation of austenite-martensite phase from tensile tests at room temperature by increments of plastic deformation. It is of great technological and scientific interest the knowledge of the evolution of phase transformation and residual stress from different levels and rates of plastic deformation imposed to the material. It is also important to evaluate the interference of metallographic preparation in quantitative analyzes of this steel. The main techniques used in this study consisted of X-rays diffraction and Ferritoscopy for the quantitation phase, and XRD to residual stress analysis also. As observed, the phase transformation quantification has not suffered significant influence of the metallographic preparation and evolved from increments of plastic deformation due to different stop charges and strain rates, leading to a further strengthening of the austenite matrix. The evaluation of residual stress resulting from the martensitic transformation was susceptible to the metallographic preparation and increased its value on comparison to sample without metallographic preparation. It was also observed that the residual stress decreased with the increase of the fraction of transformed martensite. (author)

7 CFR 22.304 - Multiyear planning and programming.

Science.gov (United States)

2010-01-01

... 7 Agriculture 1 2010-01-01 2010-01-01 false Multiyear planning and programming. 22.304 Section 22.304 Agriculture Office of the Secretary of Agriculture RURAL DEVELOPMENT COORDINATION Roles and Responsibilities of State Governments § 22.304 Multiyear planning and programming. State and multicounty...

48 CFR 11.304 - Contract clause.

Science.gov (United States)

2010-10-01

... Section 11.304 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION ACQUISITION PLANNING DESCRIBING AGENCY NEEDS Acceptable Material 11.304 Contract clause. Insert the clause at 52.211-5, Material Requirements, in solicitations and contracts for supplies that are not commercial items. ...

Estudio de la calidad de recubrimientos de hidroxiapatita sobre acero inoxidable implantable aplicados mediante proyección térmica con plasma

OpenAIRE

Bernal Gaona, Sandra Paola

2013-01-01

El objetivo de este trabajo de investigación se basó en el estudio de los parámetros del proceso de deposición de recubrimientos de hidroxiapatita sobre substratos de acero inoxidable implantable mediante el proceso de proyección térmica con plasma atmosférico, que pueden afectar de forma significativa la calidad de los recubrimientos, en cuanto a su cristalinidad y adherencia al substrato. Como parámetros a evaluar se tomaron el tamaño de grano de la hidroxiapatita, el espesor...

Response to annealing and reirradiation of AISI 304L stainless steel following initial high-dose neutron irradiation in EBR-II

International Nuclear Information System (INIS)

Porter, D.L.; McVay, G.L.; Walters, L.C.

1980-01-01

The object of this study was to measure the stability of irradiation-induced microstructure upon annealing and, by selectively annealing out some of these features and reirradiating the material, it was expected that information could be gained concerning the role of microstructural changes in the void swelling process. Transmission electron microscopic examinations of isochronally annealed (200 to 1050 0 C) AISI 304L stainless steel, which had been irradiated at approximately 415 0 C to a fast (E > 0.1 MeV) neutron fluence of approximately 5.1 x 10 26 n/m 2 , verified that the two-stage hardness recovery with temperatures was related to a low temperature annealing of dislocation structures and a higher temperature annealing of voids and solute redistribution

Superior radiation-resistant nanoengineered austenitic 304L stainless steel for applications in extreme radiation environments.

Science.gov (United States)

Sun, C; Zheng, S; Wei, C C; Wu, Y; Shao, L; Yang, Y; Hartwig, K T; Maloy, S A; Zinkle, S J; Allen, T R; Wang, H; Zhang, X

2015-01-15

Nuclear energy provides more than 10% of electrical power internationally, and the increasing engagement of nuclear energy is essential to meet the rapid worldwide increase in energy demand. A paramount challenge in the development of advanced nuclear reactors is the discovery of advanced structural materials that can endure extreme environments, such as severe neutron irradiation damage at high temperatures. It has been known for decades that high dose radiation can introduce significant void swelling accompanied by precipitation in austenitic stainless steel (SS). Here we report, however, that through nanoengineering, ultra-fine grained (UFG) 304 L SS with an average grain size of ~100 nm, can withstand Fe ion irradiation at 500 °C to 80 displacements-per-atom (dpa) with moderate grain coarsening. Compared to coarse grained (CG) counterparts, swelling resistance of UFG SS is improved by nearly an order of magnitude and swelling rate is reduced by a factor of 5. M(23)C(6) precipitates, abundant in irradiated CG SS, are largely absent in UFG SS. This study provides a nanoengineering approach to design and discover radiation tolerant metallic materials for applications in extreme radiation environments.

Low cycle fatigue: high cycle fatigue damage accumulation in a 304L austenitic stainless steel

International Nuclear Information System (INIS)

Lehericy, Y.

2007-05-01

The aim of this study was to evaluate the consequences of a Low Cycle Fatigue pre-damage on the subsequent fatigue limit of a 304L stainless steel. The effects of hardening and severe roughness (grinding) have also been investigated. In a first set of tests, the evolution of the surface damage induced by the different LCF pre-cycling was characterized. This has permitted to identify mechanisms and kinetics of damage in the plastic domain for different surface conditions. Then, pre-damaged samples were tested in the High Cycle Fatigue domain in order to establish the fatigue limits associated with each level of pre-damage. Results evidence that, in the case of polished samples, an important number of cycles is required to initiate surface cracks ant then to affect the fatigue limit of the material but, in the case of ground samples, a few number of cycles is sufficient to initiate cracks and to critically decrease the fatigue limit. The fatigue limit of pre-damaged samples can be estimated using the stress intensity factor threshold. Moreover, this detrimental effect of severe surface conditions is enhanced when fatigue tests are performed under a positive mean stress (author)

Propagation of crevices in stainless steel AISI304L in conditions of hydrogen chemistry (HWC)

International Nuclear Information System (INIS)

Diaz S, A.; Fuentes C, P.; Merino C, F.; Castano M, V.

2006-01-01

Crevice growth velocities in samples of AISI 304L stainless steel thermally welded and sensitized were obtained by the Rising displacement method or of growing displacement. It was used a recirculation circuit in where the operation conditions of a BWR type reactor were simulated (temperature of 288 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu ++ ion. CT pre cracked specimens were used and each rehearsal stayed to one constant displacement velocity of 1 x 10 -9 m/s (3.6 μm/hr), making a continuous pursuit of the advance of the crack by the electric potential drop technique. To the end of the rehearsal it was carried out the fractographic analysis of the propagation surfaces. The values of the growth velocities obtained by this methodology went similar to the opposing ones under normal conditions of operation; while the fractographic analysis show the cracks propagation in trans and intergranular ways, evidencing the complexity of the regulator mechanisms of the one IGSCC even under controlled ambient conditions or with mitigation methodologies like the alternative hydrogen chemistry. (Author)

13 CFR 304.4 - Performance evaluations.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Performance evaluations. 304.4... ECONOMIC DEVELOPMENT DISTRICTS § 304.4 Performance evaluations. (a) EDA shall evaluate the management... of at least one (1) other District Organization in the performance evaluation on a cost-reimbursement...

48 CFR 1427.304-1 - General.

Science.gov (United States)

2010-10-01

... Solicitor for the General Law Division shall issue a final determination, after consideration of any further... Section 1427.304-1 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR GENERAL CONTRACTING REQUIREMENTS PATENTS, DATA, AND COPYRIGHTS Patent Rights Under Government Contracts. 1427.304-1 General. (a)(1...

9 CFR 319.304 - Meat stews.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Meat stews. 319.304 Section 319.304... ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION DEFINITIONS AND STANDARDS OF IDENTITY OR COMPOSITION Canned, Frozen, or Dehydrated Meat Food...

5 CFR 845.304 - Financial hardship.

Science.gov (United States)

2010-01-01

...) Considerations. Some pertinent considerations in determining whether recovery would cause financial hardship are... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Financial hardship. 845.304 Section 845....304 Financial hardship. Financial hardship may be deemed to exist in, but not limited to, those...

5 CFR 304.104 - Determining rate of pay.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Determining rate of pay. 304.104 Section... CONSULTANT APPOINTMENTS § 304.104 Determining rate of pay. (a) The rate of basic pay for experts and... appropriate rate of basic pay on an hourly or daily basis, subject to the limitations described in section 304...

Corrosion study of stainless steel SS304L in molten molybdates

Energy Technology Data Exchange (ETDEWEB)

Usami, T., E-mail: tusami@criepi.denken.or.jp [Central Research Institute of Electric Power Industry, Iwadokita2-11-1, Komae-shi, Tokyo 201-8511 (Japan); Uruga, K.; Tsukada, T. [Central Research Institute of Electric Power Industry, Iwadokita2-11-1, Komae-shi, Tokyo 201-8511 (Japan); Miura, Y.; Komamine, S.; Ochi, E. [Japan Nuclear Fuel Limited, 4-108, Aza Okitsuke, Oaza Obuchi, Rokkasho-mura, Kamikita-gun, Aomori 039-3212 (Japan)

2016-04-01

Depending on operating conditions of the vitrification process of high-level liquid waste, molten salt mainly composed of sodium and molybdenum can be generated, and poured into stainless steel canisters. In this work, the possible reaction between the molten molybdate and stainless steel was investigated using multi-component molybdate and simple Na{sub 2}MoO{sub 4} – MoO{sub 3} molybdate. In the experiments using multi-component molybdates, no significant reaction is observed between the mixed molybdates and the stainless steel specimens at 700 °C in 4 h. The reaction rate of the stainless steel with the multi-component molybdate increases in proportion to exp(-1/T). The depth of the most reacted area is about 300 μm even at 1000 °C, and was much smaller than the 6 mm thickness of the canister. In the simple Na{sub 2}MoO{sub 4} – MoO{sub 3} molybdate, the reaction rate was proportional to the MoO{sub 3} concentration. The essence of the reaction is oxidation of metals by Mo{sup 6+} - > Mo{sup 4+}. Part of the reaction product mainly composed of Fe is dissolved into the molybdate, while the other part mainly composed of Cr sloughs and forms a banded layer. - Highlights: • The reaction yield of SS304L with molten molybdate was negligible at 700 °C in 4 h. • The corrosion rate increased in proportion to exp (-1/T). • The corrosion rate was proportional to MoO{sub 3} concentration in Na{sub 2}MoO{sub 4}–MoO{sub 3} mixture. • The essence of the reaction was oxidation of metals by Mo{sup 6+} –> Mo{sup 4+}.

31 CFR 596.304 - Financial transaction.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Financial transaction. 596.304 Section 596.304 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... term includes: (a) A transaction which in any way or degree affects interstate or foreign commerce; (1...

17 CFR 229.304 - (Item 304) Changes in and disagreements with accountants on accounting and financial disclosure.

Science.gov (United States)

2010-04-01

... disagreements with accountants on accounting and financial disclosure. 229.304 Section 229.304 Commodity and... accounting and financial disclosure. (a)(1) If during the registrant's two most recent fiscal years or any... any matter of accounting principles or practices, financial statement disclosure, or auditing scope or...

Influence of surface conditions on fatigue strength through the numerical simulation of microstructure; Etude par simulation numerique de la microstructure de l'influence de l'etat de surface sur la resistance a la fatigue d'un acier 304L

Energy Technology Data Exchange (ETDEWEB)

Le Pecheur, A.; Clavel, M.; Rey, C.; Bompard, P. [Laboratoire MSSMat, UMR 8579 CNRS, Ecole Centrale Paris (France); Le Pecheur, A.; Curtit, F.; Stephan, J.M. [Departement MMC, EDF RD, Site des Renardieres (France)

2010-11-15

A thermal fatigue test (INTHERPOL) was developed by EDF in order to study the initiation of cracks. These tests are carried out on tubular specimens under various thermal loadings and surface finish qualities in order to give an account of these parameters on crack initiation. The main topic of this study is to test the sensitivity of different fatigue criteria to surface conditions using a micro/macro modelling approach. Therefore a 304L polycrystalline aggregate, used for cyclic plasticity based FE modelling, have been considered as a Representative Volume Element located at the surface and subsurface of the test tube. This aggregate has been cyclically strained according to the results issued from FE simulation of INTHERPOL thermal fatigue experiment. Different surface parameters have been numerically simulated: effects of local microstructure and of grains orientation, effects of machining: metallurgical prehardening, residual stress gradient, and surface roughness. Three different fatigue criteria (Manson Coffin, Fatemi Socie and dissipated energy types), previously fitted at a macro-scale for thermal fatigue of 304L, have been computed at a meso scale, in order to show the surface 'hot spots' features and test the sensitivity of these three criteria to different surface conditions. Results show that grain orientation and neighbouring play an important role on the location of hot spots, and also that the positive effect of pre-straining and the negative effect of roughness on fatigue life are not all similarly predicted by these different fatigue criteria. (authors)

Corrosión a alta temperatura de acero al carbono y acero inoxidable austenítico en atmósferas contaminadas por CO2

OpenAIRE

Proy Pérez, Manuel

2014-01-01

Los efectos a veces catastróficos producidos por los procesos de corrosión a alta temperatura en atmósferas contaminadas por agentes agresivos, poseen la suficiente relevancia para ser objeto de estudio en los próximos años, debido a que en muchas ocasiones no están definidos claramente. Los aceros al carbono y los inoxidables austeníticos son materiales potencialmente utilizables en condiciones de elevada temperatura gracias a su excelente relación entre sus propiedades est...

47 CFR 80.304 - Watch requirement during silence periods.

Science.gov (United States)

2010-10-01

....304 Section 80.304 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Safety Watch Requirements and Procedures Ship Station Safety Watches § 80.304 Watch requirement during silence periods. Each ship station operating on...

Influence of substrate bias voltage on the properties of TiO2 deposited by radio-frequency magnetron sputtering on 304L for biomaterials applications

International Nuclear Information System (INIS)

Bait, L.; Azzouz, L.; Madaoui, N.; Saoula, N.

2017-01-01

Highlights: • TiO 2 films were deposited on stainless steel 304L RF magnetron sputtering at different substrate bias. • The hardness of TiO 2 coated 304L are higher than those obtained for uncoated substrate. • TiO 2 films provide good protection for stainless steel against corrosion in Ringer solution. - Abstract: The aim of this paper is to investigate the effect of the substrate bias, varied from 0 to −100 V, on the structure and properties of the TiO 2 thin films for biomaterials applications. The TiO 2 films were grown onto 304L stainless steel substrate using radio-frequency (rf) magnetron sputtering from a pure titanium target in Ar-O 2 gas mixture. The variation of substrate bias voltage from 0 to −100 V produces variations of structure and mechanical properties of the films. The deposited films were characterized by X-rays diffraction, nanoindentation and potentiodynamic polarization. Also, the friction and wear properties of TiO 2 films sliding against alumina ball in air were investigated. Experimental results showed that the thickness increases for non-biased substrate voltage to Vs = −100 V from 820 nm to 1936 nm respectively. The roughness is in the range of 50 nm and 14 nm. XRD results show that all structures of the films are crystalline and changed with varying the bias voltage. The anatase phase is predominant in the low negative bias range (0–50 V). The hardness significantly increased from 2.2 to 6.4 GPa when the bias voltage was increased from 0 to 75 V and then slightly decrease to 5.1 GPa as further increased to 100 V. At the same time, the results indicate that TiO 2 films deposited at −100 V exhibited better wear resistance compared to the other samples, i.e. the minimum wear rates and the lower coefficient of friction of 0.16. In order to simulate natural biological conditions, physiological serum (pH = 6.3), thermostatically controlled at 37 °C, was used as the electrolyte for the study of the electrochemical properties

40 CFR 63.304 - Standards for compliance date extension.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Standards for compliance date extension. 63.304 Section 63.304 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.304 Standards for compliance date extension. (a...

42 CFR 495.304 - Medicaid provider scope and eligibility.

Science.gov (United States)

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Medicaid provider scope and eligibility. 495.304 Section 495.304 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN... INCENTIVE PROGRAM Requirements Specific to the Medicaid Program § 495.304 Medicaid provider scope and...

Investigation of high temperature corrosion behavior on 304L austenite stainless steel in corrosive environments

Energy Technology Data Exchange (ETDEWEB)

Sahri, M. I.; Othman, N. K.; Samsu, Z.; Daud, A. R. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi Selangor (Malaysia)

2014-09-03

In this work, 304L stainless steel samples were exposed at 700 °C for 10hrs in different corrosive environments; dry oxygen, molten salt, and molten salt + dry oxygen. The corrosion behavior of samples was analyzed using weight change measurement technique, optical microscope (OM) and Scanning Electron Microscope (SEM) equipped with Energy Dispersive X-ray (EDX). The existence phases of corroded sample were determined using X-ray Diffraction (XRD). The lowest corrosion rate was recorded in dry oxygen while the highest was in molten salt + dry oxygen environments with the value of 0.0062 mg/cm{sup 2} and −13.5225 mg/cm{sup 2} respectively. The surface morphology of sample in presence of salt mixture showed scale spallation. Oxide scales of Fe{sub 3}O{sub 4}, Fe{sub 2}O{sub 3} were the main phases developed and detected by XRD technique. Cr{sub 2}O{sub 3} was not developed in every sample as protective layers but chromate-rich oxide was developed. The cross-section analysis found the oxide scales were in porous, thick and non-adherent that would not an effective barrier to prevent from further degradation of alloy. EDX analysis also showed the Cr-element was low compared to Fe-element at the oxide scale region.

Iodine-131 production by a dry method using reactor-irradiated elementary tellurium. Part 1 - Conditions for obtaining iodine emanation and its capture. Part 2 - comparative study of preparation conditions using Pyrex, stainless steel and alumina equipment. Part 3 - production on a semi-industrial scale; Production de l'iode 131 par voie seche a partir de tellure elementaire irradie a la pile. 1ere partie - Etudes des conditions pour obtenir l'emanation de l'iode et le capter. 2eme partie - Etude comparee des conditions pour effectuer cette preparation avec des appareils en Pyrex, en acier inoxydable et en alumine. 3eme partie - production a l'echelle semi-industrielle

Energy Technology Data Exchange (ETDEWEB)

Bardy, A; Beydon, J; Murthy, T S; Doyen, J B; Lefrancois, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1967-04-15

A previous report has described how iodine 131 can be prepared from elementary tellurium by a dry method which consists in treating irradiated tellurium at 400 degrees in argon. The possibility of carrying out this treatment in a stainless steel or alumina apparatus has been considered. The behavior of gaseous iodine 131 towards these materials has thus been studied. If the adsorption of iodine on stainless steel is superficial desorption is rapid at 250 degrees in oxygen or 400 degrees in argon. If the adsorption is chemical in nature it becomes necessary to heat to higher temperatures. Adsorption of iodine on alumina is very weak and the iodine can be desorbed rapidly. With these materials tests have been carried out on 300 gms of tellurium containing 41 curies of iodine 131; the yields were very satisfactory ( 98 per cent). (author) [French] La methode de preparation de l iode 131 par voie seche a partir de tellure elementaire decrite dans un precedent rapport consiste a traiter le tellure irradie a 400 degres sous argon. Nous avons examine la possibilite d effectuer ce traitement dans un appareil en acier inoxidable ou en alumine. Le comportement de l iode 131 gazeux vis a vis de ces materiaux a donc ete etudie. Si l adsorption de l iode sur l acier inoxidable est superficielle la desorption est rapide a 250 degres sous oxygene ou 400 degres sous argon. Si la fixation est de nature chimique il est necessaire de chauffer a des temperatures plus elevees. L adsorption de l iode sur l alumine est res faible et l iode peut etre desorbe rapideemnt. En employant ces materiaux des essais ont ete obtenus sur 300 g de tellure contenant 41 curies d iode 131 avec un bon rendement (98 pour cent). (auteur00.

41 CFR 101-26.304 - Substitution policy.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Substitution policy. 101-26.304 Section 101-26.304 Public Contracts and Property Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND...

Estudio de microestructura y composición de la oxidación en vapor a 700 y 750oC de los aceros austeníticos AISI 304, 316 y 317

Directory of Open Access Journals (Sweden)

José Luddey Marulanda

2013-01-01

Full Text Available Se ha investigado la oxidación de los aceros inoxidables austeníticos AISI SAE: 304, 316 y 317; a temperaturas de 700 y 750oC, en una atmósfera próxima al 100% de vapor de agua, y de 10 a 1000h de exposición. La finalidad es comprobar la calidad de los aceros austeníticos y estudiar la morfología, composición y estructura de la fases de las capas formadas en la cascarilla del óxido de las muestras por Microscopía Electrónica de Barrido (SEM, Análisis de Rayos X por Dispersión de Energía (EDAX y Difracción de Rayos X (XRD, respectivamente. Así como también, se ha realizado a diferentes tiempos un estudio sistemático de termogravimetría de las muestras oxidadas, donde se ha observado que el acero AISI 304 presentó la menor ganancia de masa y el acero AISI 316 fue el de mayor de masa respecto a los tres aceros del trabajo. Adicionalmente fue realizado un estudio teórico de simulación termodinámica de oxidación en vapor de los tres aceros, en las mismas condiciones experimentales y mediante el programa Thermo-calc. En estos aceros oxidados se han comprobado la presencia de estructuras de fases de óxidos como: Fe2O3, espinelas protectoras Fe3O4 y Cr2NiO4, y óxidos mixtos de tipo (CrxFey2O3, (Fe,Cr,Mn3O4 y Ni6MnO8. Finalmente, se discute un posible mecanismo de la formación de las capas de óxidos de las muestras ensayadas.

Um novo fio de aço inoxidável para aplicações ortodônticas A new stainless steel wire for orthodontic purposes

Directory of Open Access Journals (Sweden)

André Itman Filho

2011-08-01

Full Text Available OBJETIVO: desenvolver uma metodologia para fabricação de fios ortodônticos de aço inoxidável austeno-ferrítico SEW 410 Nr. 14517 por meio dos processos convencionais de laminação e trefilação. MÉTODOS: o aço austeno-ferrítico foi elaborado em um forno elétrico de indução. A qualidade dos fios foi avaliada por ensaios de tração e medidas de microdureza. A ductilidade e a manuseabilidade foram analisadas por meio da confecção de componentes ortodônticos. RESULTADOS E CONCLUSÕES: os valores encontrados mostraram que os fios de aço inoxidável austeno-ferrítico atenderam às normas BS 3507:1976 e ISO 5832-1, e apresentaram ótima ductilidade para confecção de componentes ortodônticos com dobras complexas.OBJECTIVE: To develop a method to manufacture austenitic-ferritic stainless steel orthodontic wires (SEW 410 Nr. 14517 using conventional rolling and wiredrawing processes. METHODS: Austenitic-ferritic steel was produced in an induction furnace. Traction trials and microhardness measurements were used to evaluate wire quality. Orthodontic parts were fabricated to assess ductility and malleability. RESULTS AND CONCLUSIONS: Austenitic-ferritic stainless steel wires meet the BS 3507:1976 and ISO 5832-1 norms and have excellent ductility for the fabrication of orthodontic parts with complex folds.

Effect of sensitization on the mechanical properties of type 304 L stainless steel

International Nuclear Information System (INIS)

Vargas Mendoza, L.F.

1990-01-01

The sensitization is a corrosion cause that it has studied broadly in the austenitic steels; however its relations don't knowed very well, into the sensitization and the steel's mechanical properties. Wherefore, the objectives of this work was to study the mechanical properties, in tension of austenitic steel with different levels of sensitization. The material utilized was a 304 L steel of standard composition AISI. The samples were sensitized at 450, 650 and 850 Centigrade degree, by short expositions, following by a temper in water. After this treatment, the tension test tubes were carried to rupture at low deformation velocity. The sensitization was evaluated by the method of Akashi EPR cyclic polarization. The sensitization distribution was analyzed by optical metallography in color and the fracture surface were studied by sweeping electronic microscopy. The distribution and length of the carbides were the factor that control the mechanic behavior of materials. At 450 Centigrade, the border of the grain its founded free of carbides, also for the longest times of exposition, but the particles are presented as fine precipitates in the grain interior, with this is increased the mechanical properties by the internal interactions of hardness or oldness types. At 650 Centigrade the frontiers show a dense distribution of fine carbides. These precipitates are interacting with the borders grain, increasing lightly the mechanical properties of steel. At 850 Centigrade, were formed discontinued carbides that not affect the mechanical behavior, but whether the fracture; the resistance is reduced and the ductility is increased although to impose the thermic effect of treatment. (Author)

Compressibility of 304 Stainless Steel Powder Metallurgy Materials Reinforced with 304 Short Stainless Steel Fibers.

Science.gov (United States)

Yao, Bibo; Zhou, Zhaoyao; Duan, Liuyang; Xiao, Zhiyu

2016-03-04

Powder metallurgy (P/M) technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass ratio. In this paper, the compressive properties of the P/M materials were characterized by a series of uniaxial compression tests. The effects of fiber content, compaction pressure and high temperature nitriding on compressive properties were investigated. The results indicated that, without nitriding, the samples changed from cuboid to cydariform without damage in the process of compression. The compressive stress was enhanced with increasing fiber content ranging from 0 to 8 wt.%. For compaction pressure from 55 to 75 MPa, greater compaction pressure improved compressive stress. Moreover, high temperature nitriding was able to significantly improve the yield stress, but collapse failure eventually occurred.

Subcooled boiling heat transfer in a short vertical SUS304-tube at liquid Reynolds number range 5.19 x 104 to 7.43 x 105

International Nuclear Information System (INIS)

Hata, Koichi; Masuzaki, Suguru

2009-01-01

The subcooled boiling heat transfer and the steady-state critical heat fluxes (CHFs) in a short vertical SUS304-tube for the flow velocities (u = 17.28-40.20 m/s), the inlet liquid temperatures (T in = 293.30-362.49 K), the inlet pressures (P in = 842.90-1467.93 kPa) and the exponentially increasing heat input (Q = Q 0 exp(t/τ), τ = 8.5 s) are systematically measured by the experimental water loop comprised of a multistage canned-type circulation pump with high pump head. The SUS304 test tubes of inner diameters (d = 3 and 6 mm), heated lengths (L = 33 and 59.5 mm), effective lengths (L eff = 23.3 and 49.1 mm), L/d (=11 and 9.92), L eff /d (=7.77 and 8.18), and wall thickness (δ = 0.5 mm) with average surface roughness (Ra = 3.18 μm) are used in this work. The inner surface temperature and the heat flux from non-boiling to CHF are clarified. The subcooled boiling heat transfer for SUS304 test tube is compared with our Platinum test tube data and the values calculated by other workers' correlations for the subcooled boiling heat transfer. The influence of flow velocity on the subcooled boiling heat transfer and the CHF is investigated into details and the widely and precisely predictable correlation of the subcooled boiling heat transfer for turbulent flow of water in a short vertical SUS304-tube is given based on the experimental data. The correlation can describe the subcooled boiling heat transfer obtained in this work within 15% difference. Nucleate boiling surface superheats for the SUS304 test tube become very high. Those at the high flow velocity are close to the lower limit of Heterogeneous Spontaneous Nucleation Temperature. The dominant mechanisms of the flow boiling CHF in a short vertical SUS304-tube are discussed.

Evaluación de diferentes aceros para la evolución de hidrógeno en KOH

Directory of Open Access Journals (Sweden)

Falk Michel Julke

2014-05-01

Full Text Available Se estudió el comportamiento electroquímico de los diferentes tipos de aceros comerciales de bajo costo (A36, 430 y 304 como electrodos para la obtención de hidrógeno. El propósito de este trabajo fue estudiar la evolución de hidrógeno, para lo cual se utilizaron técnicas electroquímicas como cronoamperometría y curvas voltamperométricas, en diferentes concentraciones de KOH (5% y 25% m/m. El acero inoxidable 304 en una concentración de 25%m/m tuvo el mejor desempeño, pues en estas condiciones el inicio de liberación de hidrógeno disminuyó y presentó el menor requerimiento de potencial para su uso como placa bipolar.

Microestructura y propiedades de capas de tribaloy T-800 depositadas mediante plaqueado láser

Directory of Open Access Journals (Sweden)

Navas, C.

2004-04-01

Full Text Available The present work is based on obtaining Co based coatings (Tribaloy T-800 on plates of 18/8 stainless steel (AISI 304 by laser cladding technique. After the treatment, samples were characterized by optical and scanning electron microscopy with EDS analysis. The elemental composition of the coating was determined with a glow discharge lamp spectrometer (GDL. The study of the interface revealed a good adherence between the substrate and coating without substantial defects. For the laser cladded coatings, the microstructure was dendritic with a high degree of refinement and chemical homogeneity close to the original powder. The grain coarsening was observed in the overlapping zones due to the second heat treatment. Microhardness of the coatings reached 750 HV, a considerably higher value than the substrate hardness (200 HV. Also, the coating corrosion resistance in saline solutions had a great improvement.

El presente trabajo se centra en la obtención de capas de aleación base Cobalto (Tribaloy T-800 sobre un sustrato de acero inoxidable 18/8 (AISI 304 mediante la técnica de plaqueado láser. Tras los tratamientos, se caracterizaron las probetas mediante microscopía óptica y electrónica de barrido con microanálisis (EDS. La composición elemental del recubrimiento se determinó en un espectrómetro de emisión óptica con fuente de excitación (GDL. El estudio de la interfase reveló una perfecta adherencia entre el recubrimiento y el material base, sin defectos apreciables. La microestructura de las capas depositadas es dendrítica con un alto grado de refinamiento y una homogeneidad química a lo largo del cordón y con valores muy próximos a los del polvo de partida. En las zonas de solape entre cordones, se observó un crecimiento del grano debido al segundo tratamiento térmico recibido. La microdureza de las capas alcanza los 750 HV, valor considerablemente superior al del sustrato (200 HV. Asimismo, se obtuvo una mejora

5 CFR 2634.304 - Gifts and reimbursements.

Science.gov (United States)

2010-01-01

... manners: (1) If the gift has been newly purchased or is readily available in the market, the value shall... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Gifts and reimbursements. 2634.304....304 Gifts and reimbursements. (a) Gifts. Except as indicated in § 2634.308(b), each financial...

32 CFR 700.304 - Recommendations to Congress.

Science.gov (United States)

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Recommendations to Congress. 700.304 Section 700... The Secretary of the Navy § 700.304 Recommendations to Congress. After first informing the Secretary of Defense, the Secretary of the Navy may make such recommendations to Congress relating to the...

Aluminum coating by fluidized bed chemical vapor deposition on austenitic stainless steels AISI 304 and AISI 316

Directory of Open Access Journals (Sweden)

Jose Luddey Marulanda-Arevalo

2015-01-01

Full Text Available Los revestimientos de aluminio f ueron depositados sobre aceros inoxidables AISI 304 y AISI 316 en el rango de temperatura de 5 60 a 600 °C por deposición química de vapor en lecho fluidizado(CVD – FBR. Se utilizó un lecho que consistía en 10 % de aluminio en polvo y 90 % de lecho inerte (alúmina, el cual fue fluidizado con Ar y como ga ses activadores se utilizó una mezcla de ácido clorhídrico con hidrógeno (HCl/H 2 . En el recubrimiento si n tratamiento térmico están las siguiente s especies: Al 13 Fe 4 , Fe 2 Al 5 , FeAl 2 y Al 5 FeNi, las cuales están presentes para ambos aceros. Además, el tratamiento térmico provoca la difusa de alu minio hacia el sustrato y la difusa de hierro del sustrato haci a la superficie del recubrimiento, haciendo la trans formación de los compuestos ant eriores a FeAl, Fe 2 Al 5 , FeAl 2 , Al 0.99 Fe 0.99 Ni 0.02 , AlNi y el Fe 2 AlCr. Se realizó la simulación termodinámica con el s oftware Thermo Calc para obt ener información de la posible composición y la cantidad de mat erial depositado, para condiciones seleccionadas. Las muestras recubi ertas y sin recubrir, se expus ieron a 750 ºC en una atmósfera d onde el vapor agua se transporta a las muestras usando un flujo de N 2 de 40 ml/min, más 100 % vapor de agua (H 2 O. Los dos sustratos sin revestir se comportaron de manera diferente, ya que el acero AISI 304 soportó bien el a taque y ganó poco peso (0.49 mg/cm 2 , en comparación con el acero AISI 316 que perdió mucho peso (25.4 mg/cm 2 . Los aceros recubiertos ganaron poco de peso durante las mil horas de exposición (0.26 mg/cm 2 y soportaron muy bien el ataque corrosivo en c omparación con sustratos sin r ecubrimiento.

9 CFR 318.304 - Operations in the thermal processing area.

Science.gov (United States)

2010-01-01

... area. 318.304 Section 318.304 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION... PREPARATION OF PRODUCTS Canning and Canned Products § 318.304 Operations in the thermal processing area. (a...

Relationship between oxide film structures and corrosion resistance of SUS 304 L stainless steel in high temperature pure water

International Nuclear Information System (INIS)

Yamanaka, Kazuo; Matsuda, Yasushi.

1990-01-01

The effect of various oxidation conditions on metal release of SUS304L stainless steels in deaerated pure water at 488 K was investigated. The behavior of metal release was also discussed in relation to the surface films which were formed by various oxidation treatments. The results obtained are as follows: (1) The oxidation treatment in high purity argon gas at high temperatures for short time such as 1273 K - 2 min (120S) was effective to decrease the metal dissolution, and the oxide films primarily consisted of spinel type double oxide layer containing high concentration of Mn and Cr. (2) The oxidation treatments in non-deaerated pure water at 561 K for 24∼336 h (86.4∼1209.6 ks) were furthermore effective to decrease the metal dissolution. (3) It may be concluded that the key factors controlling the metal release are thickness, structure and compactness together with compositions of surface oxide films. (author)

40 CFR 304.30 - Filing of pleadings.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 27 2010-07-01 2010-07-01 false Filing of pleadings. 304.30 Section... CLAIMS Hearings Before the Arbitrator § 304.30 Filing of pleadings. (a) Discovery shall be in accordance... nature of the substances contributed to the facility by each identified PRP, and a ranking by volume of...

16 CFR 304.4 - Application of other law or regulation.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Application of other law or regulation. 304.4 Section 304.4 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS RULES AND REGULATIONS UNDER THE HOBBY PROTECTION ACT § 304.4 Application of other law or...

Deformation and failure response of 304L stainless steel SMAW joint under dynamic shear loading

International Nuclear Information System (INIS)

Lee, Woei-Shyan; Cheng, J.-I.; Lin, C.-F.

2004-01-01

The dynamic shear deformation behavior and fracture characteristics of 304L stainless steel shielded metal arc welding (SMAW) joint are studied experimentally with regard to the relations between mechanical properties and strain rate. Thin-wall tubular specimens are deformed at room temperature under strain rates in the range of 8 x 10 2 to 2.8 x 10 3 s -1 using a torsional split-Hopkinson bar. The results indicate that the strain rate has a significant influence on the mechanical properties and fracture response of the tested SMAW joints. It is found that the flow stress, total shear strain to failure, work hardening rate and strain rate sensitivity all increase with increasing strain rate, but that the activation volume decreases. The observed dynamic shear deformation behavior is modeled using the Kobayashi-Dodd constitutive law, and it is shown that the predicted results are in good agreement with the experimental data. Fractographic analysis using scanning electron microscopy reveals that the tested specimens all fracture within their fusion zones, and that the primary failure mechanism is one of the extensive localized shearing. The fracture surfaces are characterized by the presence of many dimples. A higher strain rate tends to reduce the size of the dimples and to increase their density. The observed fracture features are closely related to the preceding flow behavior

Compressibility of 304 Stainless Steel Powder Metallurgy Materials Reinforced with 304 Short Stainless Steel Fibers

Directory of Open Access Journals (Sweden)

Bibo Yao

2016-03-01

Full Text Available Powder metallurgy (P/M technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass ratio. In this paper, the compressive properties of the P/M materials were characterized by a series of uniaxial compression tests. The effects of fiber content, compaction pressure and high temperature nitriding on compressive properties were investigated. The results indicated that, without nitriding, the samples changed from cuboid to cydariform without damage in the process of compression. The compressive stress was enhanced with increasing fiber content ranging from 0 to 8 wt.%. For compaction pressure from 55 to 75 MPa, greater compaction pressure improved compressive stress. Moreover, high temperature nitriding was able to significantly improve the yield stress, but collapse failure eventually occurred.

24 CFR 982.304 - Illegal discrimination: PHA assistance to family.

Science.gov (United States)

2010-04-01

... assistance to family. 982.304 Section 982.304 Housing and Urban Development Regulations Relating to Housing... Leasing a Unit § 982.304 Illegal discrimination: PHA assistance to family. A family may claim that illegal... prevents the family from finding or leasing a suitable unit with assistance under the program. The PHA must...

Martensite phase reversion-induced nano/ ultrafine grained AISI 304L stainless steel with magnificent mechanical properties

Directory of Open Access Journals (Sweden)

Mohammad Shirdel

2015-06-01

Full Text Available Austenitic stainless steels are extensively used in various applications requiring good corrosion resistance and formability. In the current study, the formation of nano/ ultrafine grained austenitic microstructure in a microalloyed AISI 304L stainless steel was investigated by the advanced thermomechanical process of reversion of strain-induced martensite. For this purpose, samples were subjected to heavy cold rolling to produce a nearly complete martensitic structure. Subsequently, a wide range of annealing temperatures (600 to 800°C and times (1 to 240 min were employed to assess the reversion behavior and to find the best annealing condition for the production of the nano/ultrafine grained austenitic microstructure. Microstructural characterizations have been performed using X-ray diffraction (XRD, scanning electron microscopy (SEM, and magnetic measurement, whereas the mechanical properties were assessed by tensile and hardness tests. After thermomechanical treatment, a very fine austenitic structure was obtained, which was composed of nano sized grains of ~ 85 nm in an ultrafine grained matrix with an average grain size of 480 nm. This microstructure exhibited superior mechanical properties: high tensile strength of about 1280 MPa with a desirable elongation of about 41%, which can pave the way for the application of these sheets in the automotive industry.

Efectos gammágenos del cobre en los aceros inoxidables 18Cr8Ni

Directory of Open Access Journals (Sweden)

Botella, J.

1997-10-01

Full Text Available From a series of 22 typical 18Cr8Ni stainless steel 40 kg ingots, with copper variable concentrations from 0.6 to 3.0 weight %, δ-ferrite is measured with a ferrite-meter device, calculating a nickel equivalent of 0.27 for copper. Some differences between the 8-ferrite and that on calculated by DeLong -excluding the copper γ-gene action- have been found because of different solidification and cooling regimes in ingot and weld cases.

A partir de una serie de 22 lingotes de 40 kg de aceros inoxidables típicos 18Cr8Ni, con concentraciones variables de cobre entre 0,6 y 3,0 % en masa, se mide la ferrita δ mediante un medidor de ferrita y se deduce para el cobre un equivalente en níquel de 0,27, a la vez que se establecen ciertas diferencias entre los contenidos de ferrita δ medida y la deducida según DeLong -excluida la acción gammágena del cobre- por el hecho de solidificar en lingotes en vez de la típica solidificación de soldaduras.

13 CFR 304.3 - District modification and termination.

Science.gov (United States)

2010-01-01

... Organization (e.g., natural disaster, plant closure, overall economic downturn, sudden and severe economic... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false District modification and termination. 304.3 Section 304.3 Business Credit and Assistance ECONOMIC DEVELOPMENT ADMINISTRATION...

22 CFR 304.9 - Referral to the Department of Justice.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Referral to the Department of Justice. 304.9... Procedures § 304.9 Referral to the Department of Justice. When Department of Justice approval or consultation is required under § 304.8, the referral or request shall be transmitted to the Department of Justice...

48 CFR 32.304-6 - Other collateral security.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Other collateral security. 32.304-6 Section 32.304-6 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... collateral security. The following are examples of other forms of security that, although seldom invoked...

Losas de concreto reforzadas con acero inoxidable de desecho Reinforced concrete slabs with stainless steel waste

Directory of Open Access Journals (Sweden)

Jorge Alberto Pérez González

2008-08-01

Full Text Available Se muestran los resultados de un programa experimental que explora la reutilización de materiales de desecho industrial (específicamente láminas de acero inoxidable producto de la acuñación de moneda como refuerzo en losas de concreto. Para ello se elaboraron 23 especímenes tipo viga-losa a escala natural con dicho refuerzo a fin de determinar su comportamiento en términos de resistencia, ductilidad y formas de falla; el análisis experimental de modelos ensayados con diferentes cantidades de refuerzo muestra que en algunos casos, bajo ciertas condiciones de cuantías y colocación del mismo, es posible alcanzar capacidades de carga y formas de falla similares a las de especímenes de control con refuerzo tradicional. En base a estos resultados se concluye en la factibilidad de utilizar el material arriba descrito como refuerzo alternativo en elementos estructurales de concreto, tratando de encontrar alternativas más económicas en la construcción de vivienda popular.The results from an experimental program that explores the use of industrial waste materials (specifically sheets of stainless steel that result of the currency coinage as reinforcement for concrete slabs are presented. Twenty three full size beam-deck specimens were built in order to measure resistance, ductility and failure modes; the experimental analysis in models with reinforcement in different quantities shows that in some cases, under certain quantities and location, it is possible to reach similar load capacities and failure modes as specimens with traditional reinforcement. Based on these results, it is concluded the feasibility of using the material described above as alternative reinforcement in structural concrete elements, as an economic option in the construction of social housing.

13 CFR 304.1 - Designation of Economic Development Districts: Regional eligibility.

Science.gov (United States)

2010-01-01

... Development Districts: Regional eligibility. 304.1 Section 304.1 Business Credit and Assistance ECONOMIC DEVELOPMENT ADMINISTRATION, DEPARTMENT OF COMMERCE ECONOMIC DEVELOPMENT DISTRICTS § 304.1 Designation of Economic Development Districts: Regional eligibility. Upon the request of a District Organization (as...

Correlaciones entre la microestructura y la atenuación sonora en un acero inoxidable martensítico

Directory of Open Access Journals (Sweden)

Daniel Ramírez C.

2004-01-01

Full Text Available En este trabajo se exploró la relación entre la microestructura de un acero inoxidable martensítico y las variaciones en el sonido producido por un instrumento metalófono construido con dicho material. Para lograr este propósito, se hicieron copias de una de las placas de un glockenspiel y éstas fueron sometidas a diferentes tratamientos térmicos. Se construyeron montajes que permitieron producir sonidos mediante la excitación por percusión o electromagnética de las placas y se desarrollaron procedimientos para el análisis de las señales adquiridas usando programas de que permitían un análisis automático de la información. A partir de los resultados fue posible establecer correlaciones entre la microestructura obtenida con los diferentes tratamientos térmicos y características de los sonidos tales como la envolvente de atenuación y frecuencias predominantes.

42 CFR 3.304 - Principles for achieving compliance.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Principles for achieving compliance. 3.304 Section 3.304 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL... Principles for achieving compliance. (a) Cooperation. The Secretary will, to the extent practicable, seek the...

Efecto del contenido de azufre y del grado de desoxidación sobre la ductilidad en caliente de aceros inoxidables austeníticos resulfurados en estado de solidificación

Directory of Open Access Journals (Sweden)

Botella, J.

1998-05-01

Full Text Available The manufacture of free machining austenitic stainless steels features a specific drawback derived from their high sulphur content, which is needed for generating, into the austenitic matrix, inclusions to optimize the different machining operations. However, sulphur has a harmful effect on hot workability. This paper deals with assessing the effect of sulphur content and deoxidation level on the hot ductility of resulphurized austenitic stainless steels in as cast condition. Hot tensile tests were conducted on a Gleeble machine, at temperatures between 1,150 and 1,250°C, studying a ductility factor as a function of sulphur content, deoxidation degree, as well as type, size and distribution of sulfides. Results point out the harmful effect of increasing sulphur and oxygen contents on the hot workability of resulphurized austenitic stainless steels, and the need to control carefully the level of oxides of these steels.

La fabricación de aceros inoxidables austeníticos de alta maquinabilidad presenta una problemática específica derivada de su elevado contenido de azufre; elemento necesario para generar en la matriz austenítica inclusiones que faciliten las diferentes operaciones de mecanizado, pero perjudicial en cuanto al deterioro que produce en la deformabilidad en caliente. Este artículo describe el estudio realizado para evaluar el efecto del contenido de azufre y el grado de desoxidación sobre la ductilidad en caliente de aceros inoxidables austeníticos resulfurados, partiendo de una estructura de solidificación (as cast condition. Se realizaron ensayos de tracción en un sistema Gleeble, a temperaturas entre 1.150 y 1.250°C, analizándose el parámetro de ductilidad en función del contenido de azufre, nivel de desoxidación, y del tipo, tamaño y distribución de los sulfuros presentes. Los resultados ponen de manifiesto el efecto perjudicial de los contenidos de azufre y oxígeno sobre la deformabilidad en

Influence of substrate bias voltage on the properties of TiO{sub 2} deposited by radio-frequency magnetron sputtering on 304L for biomaterials applications

Energy Technology Data Exchange (ETDEWEB)

Bait, L. [Division Milieux Ionisés et Lasers, Centre de Développement des Technologies Avancées, CDTA,Cité du 20 aout 1956, Baba Hassen, BP n°. 17, Alger (Algeria); Azzouz, L. [Université de Amar Telidji, Laghouat (Algeria); Madaoui, N. [Division Milieux Ionisés et Lasers, Centre de Développement des Technologies Avancées, CDTA,Cité du 20 aout 1956, Baba Hassen, BP n°. 17, Alger (Algeria); Saoula, N., E-mail: nsaoula@cdta.dz [Division Milieux Ionisés et Lasers, Centre de Développement des Technologies Avancées, CDTA,Cité du 20 aout 1956, Baba Hassen, BP n°. 17, Alger (Algeria)

2017-02-15

Highlights: • TiO{sub 2} films were deposited on stainless steel 304L RF magnetron sputtering at different substrate bias. • The hardness of TiO{sub 2} coated 304L are higher than those obtained for uncoated substrate. • TiO{sub 2} films provide good protection for stainless steel against corrosion in Ringer solution. - Abstract: The aim of this paper is to investigate the effect of the substrate bias, varied from 0 to −100 V, on the structure and properties of the TiO{sub 2} thin films for biomaterials applications. The TiO{sub 2} films were grown onto 304L stainless steel substrate using radio-frequency (rf) magnetron sputtering from a pure titanium target in Ar-O{sub 2} gas mixture. The variation of substrate bias voltage from 0 to −100 V produces variations of structure and mechanical properties of the films. The deposited films were characterized by X-rays diffraction, nanoindentation and potentiodynamic polarization. Also, the friction and wear properties of TiO{sub 2} films sliding against alumina ball in air were investigated. Experimental results showed that the thickness increases for non-biased substrate voltage to Vs = −100 V from 820 nm to 1936 nm respectively. The roughness is in the range of 50 nm and 14 nm. XRD results show that all structures of the films are crystalline and changed with varying the bias voltage. The anatase phase is predominant in the low negative bias range (0–50 V). The hardness significantly increased from 2.2 to 6.4 GPa when the bias voltage was increased from 0 to 75 V and then slightly decrease to 5.1 GPa as further increased to 100 V. At the same time, the results indicate that TiO{sub 2} films deposited at −100 V exhibited better wear resistance compared to the other samples, i.e. the minimum wear rates and the lower coefficient of friction of 0.16. In order to simulate natural biological conditions, physiological serum (pH = 6.3), thermostatically controlled at 37 °C, was used as the electrolyte for the

Plasticity-induced martensitic transformation in austenitic stainless steels SUS 304 and SUS 316 L at room and liquid nitrogen temperatures. Quantitative measurement using X-ray diffraction method

International Nuclear Information System (INIS)

Iwasaki, Yoshifumi; Nakasone, Yuji; Shimizu, Tetsu; Kobayashi, Noboru

2006-01-01

The present study investigates plasticity-induced martensitic transformation in two types of austenitic stainless steels SUS 304 and 316 L subjected to uniform tensile stresses at room and liquid nitrogen temperatures. The X-ray diffraction method was used in order to measure volume fractions of transformed α' and ε' martensitic phases and to obtain the dependence of the volume fractions of these phases on the applied strain level ε. The difficulty in the measurement of the martensitic phases by the X-ray diffraction method caused by the preferred orientation which had been introduced during the rolling process and during the tensile tests was overcome by the help of Arnell's Method. Two types of target materials, i.e. Cu and Mo for the X-ray source were used to verify the accuracy and reproducibility of the present X-ray diffraction analyses. The results were also compared with those obtained by the saturation magnetization method using VSM, or vibrating-sample magnetometer reported elsewhere. It was revealed that α' was transformed in SUS 304 both at 297 and 77 K whereas in SUS 316L only at 77 K. Another type of martensitic phase, i.e., ε was transformed in the both steels only at 77 K. Almost the same values of the volume fractions of α' and ε' phases were obtained by the two types of target materials. The plots of α' volume fraction obtained by the X-ray diffraction methods vs. that by VSM showed a good linear correlation. (author)

INTEGRAL hard X-ray detection of HMXB GX 304-1 and H1417-624

DEFF Research Database (Denmark)

Manousakis, A.; Beckmann, V.; Bianchin, V.

2008-01-01

We report on the first detection of the Be star HMXBs GX 304-1 and H1417-624 above 20 keV with the IBIS/ISGRI X-ray imager on board INTEGRAL. From 2008-06-24 to 2008-07-09, INTEGRAL performed monitoring observations of the Galactic plane around l=305 degrees for a total exposure time of 352 ksec....

27 CFR 70.304 - Place for filing documents other than returns.

Science.gov (United States)

2010-04-01

...: Members of the taxpayer's family, an employee of the taxpayer, the taxpayer's attorney, accountant, or tax... other than returns. 70.304 Section 70.304 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX... ADMINISTRATION Collection of Excise and Special (Occupational) Tax Miscellaneous Provisions § 70.304 Place for...

Oxidation behavior of TiC particle-reinforced 304 stainless steel

International Nuclear Information System (INIS)

Wu Qianlin; Zhang Jianqiang; Sun Yangshan

2010-01-01

TiC particle-reinforced 304 stainless steels were prepared using a new developed in situ technology and exhibited the uniform distribution of TiC particles in the matrix. The oxidation behavior of 304SS-2TiC and 304SS-6TiC (all in weight percentage) was compared with that of 304SS at 850 deg. C in air for 96 h using thermogravimetry analysis. For 304SS, the rate of weight gain was very slow initially, but accelerated suddenly to a very high level, forming breakaway oxidation. The addition of TiC particles to 304SS resulted in no breakaway oxidation and maintained a low oxidation rate in the whole reaction time investigated. Examination of oxide scale morphology and cross-section analysis by scanning electron microscopy and optical microscopy showed a significant scale spallation and a deep oxide penetration in the case of 304SS, but a rather continuous, dense and adherent oxide layer formed on the surface of TiC particle-reinforced alloys. XRD analysis revealed the presence of Cr 2 O 3 together with spinel-type oxides in the oxide scale. For TiC-containing alloys, fine TiO 2 was also found on the surface and the amount of this oxide increased with TiC addition. The TiC addition developed finer matrix structure before oxidation, which accelerates chromium diffusion. As a result, scale adherence was improved and oxidation resistance was increased.

High temperature oxidation behavior of AISI 304L stainless steel—Effect of surface working operations

International Nuclear Information System (INIS)

Ghosh, Swati; Kumar, M. Kiran; Kain, Vivekanand

2013-01-01

Highlights: ► Surface working resulted in thinner oxide on the surface. ► Oxides on machined/ground surfaces richer in Cr, higher in specific resistivity. ► Additional ionic transport process at the metal-oxide for ground sample established. ► Presence of fragmented grains and martensite influenced oxide nature/morphology. - Abstract: The oxidation behavior of grade 304L stainless steel (SS) subjected to different surface finishing (machining and grinding) operations was followed in situ by contact electric resistance (CER) and electrochemical impedance spectroscopy (EIS) measurements using controlled distance electrochemistry (CDE) technique in high purity water (conductivity −1 ) at 300 °C and 10 MPa in an autoclave connected to a recirculation loop system. The results highlight the distinct differences in the oxidation behavior of surface worked material as compared to solution annealed material in terms of specific resistivity and low frequency Warburg impedance. The resultant oxide layer was characterized for (a) elemental analyses by glow discharge optical emission spectroscopy (GDOES) and (b) morphology by scanning electron microscopy (SEM). Oxide layers with higher specific resistivity and chromium content were formed in case of machined and ground conditions. Presence of an additional ionic transport process has also been identified for the ground condition at the metal/oxide interface. These differences in electrochemical properties and distinct morphological features of the oxide layer as a result of surface working were attributed to the prevalence of heavily fragmented grain structure and presence of martensite.

Study of interaction of fatigue damage and ratcheting. Effect of a tensile primary load on torsion fatigue resistance of stainless steel 304 L at ambient temperature

International Nuclear Information System (INIS)

Hakem, N.S.

1987-01-01

Effect of ratcheting on fatigue resistance of a stainless steel 304 L, used for reactor vessels, is studied experimentally. Lifetime of samples is reduced if a static constant tensile load (primary loading) is superimposed to cyclic torsion deformations (secondary loading). An equivalent deformation concept is developed to express a criterion of fatigue rupture under primary loading. No effect is noted on the curve of cyclic strain hardening. This fatigue analysis gives no information on cumulated axial deformation. Progressive elongation, observed during testing, is dependent of primary and secondary loading. Rupture is produced by fatigue because cumulated axial deformation is limited ( 4 cycles at rupture cumulated deformation is [fr

Thermal fatigue of a 304L austenitic stainless steel: simulation of the initiation and of the propagation of the short cracks in isothermal and aniso-thermal fatigue; Fatigue thermique d'un acier inoxydable austenitique 304L: simulation de l'amorcage et de la croissance des fissures courtes en fatigue isotherme et anisotherme

Energy Technology Data Exchange (ETDEWEB)

Haddar, N

2003-04-01

The elbow pipes of thermal plants cooling systems are submitted to thermal variations of short range and of variable frequency. These variations bound to temperature changes of the fluids present a risk of cracks and leakages. In order to solve this problem, EDF has started the 'CRECO RNE 808' plan: 'thermal fatigue of 304L austenitic stainless steels' to study experimentally on a volume part, the initiation and the beginning of the propagation of cracks in thermal fatigue on austenitic stainless steels. The aim of this study is more particularly to compare the behaviour and the damage of the material in mechanic-thermal fatigue (cycling in temperature and cycling in deformation) and in isothermal fatigue (the utmost conditions have been determined by EDF for the metal: Tmax = 165 degrees C and Tmin = 90 degrees C; the frequency of the thermal variations can reach a Hertz). A lot of experimental results are given. A model of lifetime is introduced and validated. (O.M.)

Phosphate coating on stainless steel 304 sensitized

International Nuclear Information System (INIS)

Cruz V, J. P.; Vite T, J.; Castillo S, M.; Vite T, M.

2009-01-01

The stainless steel 304 can be sensitized when welding processes are applied, that causes the precipitation of chromium carbide in the grain limits, being promoted in this way the formation of galvanic cells and consequently the corrosion process. Using a phosphate coating is possible to retard the physiochemical damages that can to happen in the corrosion process. The stainless steel 304 substrate sensitized it is phosphate to base of Zn-Mn, in a immersion cell very hot. During the process was considered optimization values, for the characterization equipment of X-rays diffraction and scanning electron microscopy was used. The XRD technique confirmed the presence of the phases of manganese phosphate, zinc phosphate, as well as the phase of the stainless steel 304. When increasing the temperature from 60 to 90 C in the immersion process a homogeneous coating is obtained. (Author)

Estudio de electrodeposición de cobre sobre electrodos porosos de grafito y acero inoxidable vía SEM-DRX y análisis de imagen

OpenAIRE

Constanzo-R., Robinson; Pagliero-N., Antonio; Vergara-G., Froilán

2014-01-01

El objetivo de este trabajo fue realizar un análisis cualitativo de la distribución de un electrodepósito de cobre en el interior de electrodos porosos (EP) de acero inoxidable y carbono grafito. Para ello, se realizaron pruebas de electrodepositación de cobre a nivel de laboratorio, con un posterior análisis de cortes de muestras de acero y grafito vía Microscopía Estereoscópica, Microscopía SEM-DRX y Análisis de Imagen, los cuales mostraron que el cobre no se deposita en forma uniforme al i...

5 CFR 530.304 - Establishing or increasing special rates.

Science.gov (United States)

2010-01-01

... involved (including exposure to toxic substances or other occupational hazards); or (4) Any other... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Establishing or increasing special rates. 530.304 Section 530.304 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE...

Formação de biofilme por Pseudomonas aeruginosa sobre aço inoxidável em contato com leite e seu controle por óleos essenciais

Directory of Open Access Journals (Sweden)

Nádia Nara BATISTA

2014-01-01

Full Text Available Objetivo: Avaliar a ação bacteriostática e bactericida de diferentes óleos essenciais sobre células planctônicas de Pseudomonas aeruginosa ATCC 27853, bem como verificar a ação sanitizante, dos óleos essenciais que apresentarem a menor Concentração Mínima Inibitória (CMI, sobre o biofilme formado por esta espécie, Material e Métodos: A ação bacteriostática foi realizada por meio da determinação das CMIs dos óleos de Zingiber officinale, Eugenia caryophyllus, Elettaria cardamomum, Citrus limon e Citrus reticulata v, tangerine, O tempo de morte bacteriana foi determinado utilizando-se as CMIs de cada óleo essencial submetidos a diferentes tempos de contato, O biofilme de P, aeruginosa foi desenvolvido em cupons de aço inoxidável AISI 304 dispostos em placa de Petri contendo leite tratado por Ultra Alta Temperatura (UAT, sendo incubado sob agitação de 70 rpm, a 37 °C/96 horas, Células aderidas foram removidas através de swabs e enumeradas por contagem em placas após submissão a diferentes tratamentos, Resultados: Todos os óleos essenciais apresentaram efeito bacteriostático, se destacando Z, officinale, E, caryophyllus e E, cardamomum, por apresentarem menor CMI, O tempo de morte de P, aeruginosa foi de 10 minutos quando utilizadas soluções a base de E, cardamomum e E, caryophyllus, No entanto, quando testados em biofilme, apenas E, caryophyllus eliminou as células bacterianas viáveis de P, aeruginosa, Conclusão: E, caryophyllus é uma nova alternativa para o controle do biofilme de P, aeruginosa na indústria de alimentos, pois, além de sua alta atividade antimicrobiana, é um composto natural, o que atende as exigências do mercado consumidor.

Passivation of duplex stainless steel in solutions simulating chloride-contaminated concrete

Directory of Open Access Journals (Sweden)

Takenouti, H.

2007-12-01

Full Text Available Most studies published to date on the corrosion behaviour of stainless reinforcing steel are based on austenitic steel. The market presence of corrugated duplex steel is growing, however. The present study compared passivity in 2205 type duplex and 304 type austenitic stainless steel. Polarization tests in chloride-containing Ca(OH2 solutions confirmed the exceptional performance of duplex steels. X-ray photoelectronic spectroscopy (XPS showed that the passive layer generated on duplex stainless steel in media simulating concrete pore solutions had a higher Cr content than the layer formed on steel in contact with the air. The XPS results also revealed that in duplex steel the form adopted by the passive layer Fe oxides was Fe3O4 in the solutions simulating concrete, rather than Fe2O3, as in duplex steel exposed to air. Electrochemical impedance spectroscopy (EIS can be used to monitor the transformations taking place in the passive layer and analyze the factors involved.La mayoría de los estudios publicados hasta el momento sobre el comportamiento frente a la corrosión de armaduras de acero inoxidable se basan en aceros austeníticos. Sin embargo, la presencia en el mercado de aceros corrugados dúplex es cada vez más importante. En este trabajo se analiza la pasividad de un acero inoxidable dúplex tipo 2205 en comparación con la de un inoxidable austenítico tipo 304. Los ensayos de polarización en disoluciones de Ca(OH2 con cloruros confirman el excepcional comportamiento de los aceros dúplex. La espectroscopía fotoelectrónica de rayos X (XPS informa de que la capa pasiva generada en aceros inoxidables dúplex en medios que simulan la disolución de los poros del hormigón posee mayor contenido en óxidos de Cr que la formada en aire. También se puede deducir de los resultados de XPS que los óxidos de Fe de la capa pasiva de los aceros dúplex se encuentran en forma de Fe3O4 en las disoluciones que simulan el hormigón en vez de en

Estudio de la viabilidad de fabricación de un sistema codo (fundición inoxidable ferrítica, GX 260 Cr27-tubo composite (Incolloy 800 HT+Stal 2465 solidario por fusión

Directory of Open Access Journals (Sweden)

Gutiérrez de Solabarría, S.

1995-10-01

Full Text Available Flying ashes captured by ciclones in the experimental plant for combustion in pressure fluid bed, in Escatrón Power Plant (Zaragoza, Spain, circulate through the gas cleaning system and are evacuated by means of pneumatic transport. The temperature of these ashes is aprox. 800 °C and the relative pressure is up to 8 negative bars relating the outdoor pressure of the transport pipe. The configuration of the pneumatic transport lines is Incolloy 800 HT quality composite tubes lined with Stal 2465 in straight stretches. Regarding direction changes, ferritic stainless casting, quality GX 260 Cr 27 elbows are used. The aim of this work is to study the possibility of manufacturing a solidary system by means of melting between the ferritic stainless casting elbow and the composite pipe.

Las cenizas volantes captadas por ciclones en la planta experimental de combustión en lecho fluido a presión, de la central térmica de Escatrón (Zaragoza, circulan por el sistema de depuración de gases y son evacuadas mediante transporte neumático. Estas cenizas se encuentran a una temperatura aproximada de 800 °C y a una presión relativa de hasta 8 bares negativos con respecto a la presión en el exterior de la tubería de transporte. Para configurar las líneas de transporte neumático, se utilizan en los tramos rectos tubos composite de calidad Incolloy 800 HT recubiertos interiormente de material Stal 2465. Para los cambios de dirección, se utilizan codos de fundición inoxidable ferrítica de calidad GX 260 Cr 27. El objetivo del presente trabajo es estudiar la viabilidad de fabricación de un sistema solidario por fusión entre el codo de fundición inoxidable ferrítica y la tubería composite.

Decapado de un acero inoxidable austenítico mediante mezclas ecológicas basadas en H2O2 - H2SO4 - iones F-

Directory of Open Access Journals (Sweden)

Narváez, L.

2013-04-01

Full Text Available This study reports the pickling of 316L stainless steel using mixtures of hydrogen peroxide (H2O2, sulphuric acid (H2SO4 and fluoride ions as hydrofluoric acid (HF, sodium fluoride (NaF and potassium fluoride (KF. The decomposition of H2O2 in the mixtures was assessed at different temperatures 25 °C to 60 °C, with ferric ion contents from 0 to 40 g/l. According to the results obtained, were established the optimal condition pickling at 20 g/l of ferric ions, 25 °C and p-toluensulphonic acid as stabilizer of H2O2. The HF pickling mixture was the only capable to remove totally the oxide layer from the 316L stainless steel after 300 s. The fluoride salts pickling mixtures only remove partially the oxide layer (20 to 40 % aprox. after 300 s. When the pickling time was increased until 1200 s, the removal percentages were around to 80 %.En este estudio se presenta el decapado del acero inoxidable austenítico 316L utilizando mezclas de peróxido de hidrógeno (H2O2/ácido sulfúrico (H2SO4/iones fluoruro; los iones fluoruro provienen del ácido fluorhídrico (HF, fluoruro de sodio (NaF y fluoruro de potasio (KF. La estabilidad del H2O2 fue valorada modificando las concentraciones del ión férrico de 0 a 40 g/l y las temperaturas de 25 °C a 60 °C en las mezclas decapantes. Se establecieron las condiciones óptimas de decapado utilizando 20 g/l de iones férrico a 25 °C empleando el ácido p-toluensulfónico como estabilizante del H2O2. La mezcla que contenía HF fue la única capaz de eliminar completamente los óxidos superficiales del acero a tiempos de 300 s. Las mezclas a base de sales fluoradas eliminaron parcialmente los óxidos (20 y 40 % aprox. en 300 s. Al incrementar el tiempo de decapado hasta 1200 s se obtuvieron porcentajes de eliminación alrededor de un 80 %.

45 CFR 73.735-304 - Use of government property.

Science.gov (United States)

2010-10-01

.... (Exception for employee welfare and recreation associations is stated in Chapter 25-10, General... 45 Public Welfare 1 2010-10-01 2010-10-01 false Use of government property. 73.735-304 Section 73.735-304 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION STANDARDS OF...

PengaruhKorosiAir LautpadaKekuatanTarik SambunganLas KombinasiStainless Steel 304-201

Directory of Open Access Journals (Sweden)

Tjokorda Gde Tirta Nindhia

2016-07-01

Full Text Available Abstrak: Instalasi konstruksi yang dibangun dengan bahan stainless steel merupakan pilihan pertama dari daftar lis yang akan digunakan untuk konstruksi dekat laut. Dengan ditemukannya teknologi tungsten inert gas (TIG belakangan ini maka kontruksi dengan bahan stainles steel dapat direalisasikan. Dalam beberapa kasus sampungan las stainless steel dilakukan dengan menyambung dengan stainless steel dari jenis yang berbeda tanpa peduli dengan kekuatan yang dihasilkan khusunya jika mengalami korosi dalam hal ini korosi akibat air laut. Dalam penelitian ini kekuatan tarik sambungan kombinasi stainles steel dari jenis 304- 201 diuji dan dibandingkan dengan sambungan sejenis dari jenis 304-304 dan 201-201 Pengerauh korosi air laut terhadap kekuatan tarik sambungan stainless steel tersebut juga diteliti. Penelitian menemukan bahwa kekuatan tarik paling tinggi dimiliki oleh sambungan sejenis 304-304 diikuti oleh samnbungan kombinasi 304-201 dan yang terendah adalah sambungan 201-201. Pengaruh korosi airlaut diketahui menurunkan kekuatan dari semua jenis sambungan Kata Kunci : Stainless steel, las, air laut, korosi, kekuatan tarik Abstract: Installation of construction made from stainless steel is in the first list to be selected for location near the sea. The construction is by recent technology is much realize by using welding technology especially tungsten inert gas (TIG. In some case the welded joint of stainless steel are realized by joining 2 different type of stainless steel such as between type of 304 and 201 without any concern to the strength that will be achieved especially after exposure to the sea water. In this research the tensile strength of a combination of welding between stainless steel of 304- 201 is tested and compare to the welded of 304-304 and welded of 201-201. The effect of sea water corrosion in 30 days to the strength of the welded joint is observed . It is found that the tensile strength of welded 304-304 is found the highest

Simulation and experimental comparison of the thermo-mechanical history and 3D microstructure evolution of 304L stainless steel tubes manufactured using LENS

Science.gov (United States)

Johnson, Kyle L.; Rodgers, Theron M.; Underwood, Olivia D.; Madison, Jonathan D.; Ford, Kurtis R.; Whetten, Shaun R.; Dagel, Daryl J.; Bishop, Joseph E.

2017-12-01

Additive manufacturing enables the production of previously unachievable designs in conjunction with time and cost savings. However, spatially and temporally fluctuating thermal histories can lead to residual stress states and microstructural variations that challenge conventional assumptions used to predict part performance. Numerical simulations offer a viable way to explore the root causes of these characteristics, and can provide insight into methods of controlling them. Here, the thermal history of a 304L stainless steel cylinder produced using the Laser Engineered Net Shape process is simulated using finite element analysis (FEA). The resultant thermal history is coupled to both a solid mechanics FEA simulation to predict residual stress and a kinetic Monte Carlo model to predict the three-dimensional grain structure evolution. Experimental EBSD measurements of grain structure and in-process infrared thermal data are compared to the predictions.

Simulation and experimental comparison of the thermo-mechanical history and 3D microstructure evolution of 304L stainless steel tubes manufactured using LENS

Science.gov (United States)

Johnson, Kyle L.; Rodgers, Theron M.; Underwood, Olivia D.; Madison, Jonathan D.; Ford, Kurtis R.; Whetten, Shaun R.; Dagel, Daryl J.; Bishop, Joseph E.

2018-05-01

Additive manufacturing enables the production of previously unachievable designs in conjunction with time and cost savings. However, spatially and temporally fluctuating thermal histories can lead to residual stress states and microstructural variations that challenge conventional assumptions used to predict part performance. Numerical simulations offer a viable way to explore the root causes of these characteristics, and can provide insight into methods of controlling them. Here, the thermal history of a 304L stainless steel cylinder produced using the Laser Engineered Net Shape process is simulated using finite element analysis (FEA). The resultant thermal history is coupled to both a solid mechanics FEA simulation to predict residual stress and a kinetic Monte Carlo model to predict the three-dimensional grain structure evolution. Experimental EBSD measurements of grain structure and in-process infrared thermal data are compared to the predictions.

Electrical conductivity of air under the action of a shock wave; Conductivite electrique de l'air sous l'action d'une onde de choc

Energy Technology Data Exchange (ETDEWEB)

Thouvenin, Jacques [Commissariat a l' energie atomique et aux energies alternatives - CEA (France)

1960-07-01

A method is described for the measurement of the electrical conductivity of a shock wave in air. The results reveal the preponderant part played by the NO molecule. Reprint of a paper published in Comptes rendus des seances de l'Academie des Sciences, t. 250, p. 302-304, sitting of 11 January 1960 [French] On decrit un procede de mesure de la conductivite electrique d'une onde de choc dans l'air. Les resultats font apparaitre le role preponderant joue par la molecule NO. Reproduction d'un article publie dans les Comptes rendus des seances de l'Academie des Sciences, t. 250, p. 302-304, seance du 11 janvier 1960.

Brasagem dos aços inoxidáveis duplex 'baixa liga' UNS S32101, UNS S32304 e superduplex UNS S32750 com metal de adição AWS A5.3 tipo BNi-7 (Ni-Cr-P

Directory of Open Access Journals (Sweden)

Dany Michell Andrade Centeno

2013-12-01

Full Text Available Os aços inoxidáveis duplex, devido à sua resistência à corrosão, têm uma grande aplicação em diversos segmentos industriais, onde a resistência à corrosão é uma propriedade requerida. Por terem resistência mecânica superior aos aços inoxidáveis ferríticos e austeníticos convencionais, podem produzir equipamentos mais leves. Quando ciclados termicamente, estes aços podem ter suas propriedades alteradas, principalmente quando se emprega processos de junção, como a brasagem, e quando ocorre o desbalanceamento da fração volumétrica ferrita/austenita. O objetivo deste trabalho é caracterizar a brasagem de aços inoxidáveis duplex 'baixa liga' e superduplex, verificando o efeito da folga e do tempo de brasagem na formação de intermetálicos contínuos no interior da junta brasada. Neste trabalho foram brasados, em forno continuo com atmosfera de hidrogênio, corpos-de-prova de aço inoxidável duplex UNS S32101, UNS S32304 e UNS S32750 com a adição para brasagem BNi-7 (Ni-Cr-P, na temperatura de 1100ºC, por tempos de 12 min e 32 min, utilizando-se folgas das juntas de 0,0 e 0,3 mm, seguidos de resfriamento em forno. Os corpos de prova foram caracterizados utilizando-se microscópio óptico, microscópio eletrônico de varredura com EDS e difração de raios X. Os resultados mostraram que a melhor condição para a brasagem em forno empregado foi a brasagem com a folga de 0,0 mm. Ambas as folgas apresentaram microestruturas variadas, porém a folga de 0,0 mm mostrou a presença de uma fase contínua CFC (cúbica de face centrada, rica em níquel, que é denominada, frequentemente, de γ-Ni. Para folgas de 0,3 mm, forma-se uma região eutética contínua no centro da junta, que pode prejudicar as propriedades mecânicas da mesma. Esta região é composta de fases intermetálicas ricas em fósforo. Foram observadas precipitações de fase sigma no metal de base no AID UNS S35750, nas condições de brasagem estudadas.

29 CFR 541.304 - Practice of law or medicine.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Practice of law or medicine. 541.304 Section 541.304 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR REGULATIONS DEFINING AND DELIMITING THE EXEMPTIONS FOR EXECUTIVE, ADMINISTRATIVE, PROFESSIONAL, COMPUTER AND OUTSIDE SALES EMPLOYEES Professional Employees §...

Designing of CK45 carbon steel and AISI 304 stainless steel dissimilar welds

OpenAIRE

Pouraliakbar,Hesam; Hamedi,Mohsen; Kokabi,Amir Hossein; Nazari,Ali

2014-01-01

Gas tungsten arc welding of CK45 and AISI304 stainless steel was performed through preparation of different types of samples using ER308L and ERNi-1 wires. Welded samples were studied by different techniques including optical metallography, scanning electron microscopy equipped with energy dispersive X-ray spectroscopy (SEM-EDS), X-ray diffraction, hardness measurements and impact test. It was observed that in the buttered specimen, the structure of the weld metal was completely austenitic wh...

Analysis of AISI 304 Tensile Strength as an Anchor Chain of Mooring System

Science.gov (United States)

Hamidah, I.; Wati, R.; Hamdani, R. A.

2018-05-01

The background of this research is the use of mild steel (i.e., St37) as anchor chain that works on the corrosive environment of seawater which is possible to decrease its tensile strength. The longer soaked in seawater, the more significant the lowering of its tensile strength. Anchor chain needs to be designed by considering its tensile strength and corrosion resistance, so it’s able to support mooring system well. The primary purpose of this research is obtaining the decreasing of stainless steel 304 (AISI 304) tensile strength which is corroded by seawater as anchor chain of the mooring system. It is also essential to obtain the lifetime of AISI304 and St37 as anchor chain with the same load, the corrosion rate of AISI 304, and St 37 in seawater. The method which was employed in this research is an experiment with four pieces of stainless steel AISI 304, and of St 37 corrosion testing samples, six pieces of stainless steel 304, and six pieces of St 37 for tensile testing samples. The result of this research shows that seawater caused stainless steel AISI 304 as anchor chain has decreased of tensile strength about 1.68 % during four weeks. Also, it indicates that AISI 304 as anchor chain has a lifetime about 130 times longer than St 37. Further, we found that the corrosion rate of stainless steel 304 in seawater is 0.2042 mpy in outstanding category, while the St 37 samples reached up to 27.0247 mpy ranked as fair category. This result recommends that AISI 304 more excellence than St 37 as anchor chain of the mooring system.

Oxidación en vapor de agua a 700 ºC y 750 ºC del acero inoxidable AISI 317 recubierto con aluminio por CVD-FBR.

OpenAIRE

Jose L. Marulanda; Saul I. Castañeda; Aduljay Remolina

2014-01-01

Se realizó la oxidación del acero inoxidable austenítico AISI 317 recubierto con aluminio por deposición química de vapor en lecho fluidizado, a temperaturas de 700 °C y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de SEM y difracción de rayos X, para observar la morfología de los óxidos. Se realizó la simulación termodinámica del proceso de oxidación en vapor de agua de...

The astaxanthin dideoxyglycoside biosynthesis pathway in Sphingomonas sp. PB304

DEFF Research Database (Denmark)

Kim, Se Hyeuk; Kim, Jin Ho; Lee, Bun Yeol

2014-01-01

A major carotenoid in Sphingomonas sp. PB304, originally isolated from a river in Daejon City, South Korea, was identified as astaxanthin dideoxyglycoside. Gene clusters encoding the astaxanthin dideoxyglycoside biosynthetic enzymes were identified by screening Sphingomonas sp. PB304 fosmid...

Nanosecond laser surface modification of AISI 304L stainless steel: Influence the beam overlap on pitting corrosion resistance

International Nuclear Information System (INIS)

Pacquentin, Wilfried; Caron, Nadège; Oltra, Roland

2014-01-01

Surface modifications of AISI 304L stainless steel by laser surface melting (LSM) were investigated using a nanosecond pulsed laser-fibre doped by ytterbium at different overlaps. The objective was to study the change in the corrosion properties induced by the treatment of the outer-surface of the stainless steel without modification of the bulk material. Different analytical techniques such as scanning electron microscopy (SEM), X-ray diffraction (XRD), and glow discharge optical emission spectrometry (GDOES) were used to characterize the laser-melted surface. The corrosion resistance was evaluated in a chloride solution at room temperature by electrochemical tests. The results showed that the crystallographic structure, the chemical composition, the properties of the induced oxide layer and consequently the pitting corrosion resistance strongly depend on the overlap rate. The most efficient laser parameters led to an increase of the pitting potential by more than 300 mV, corresponding to a quite important improvement of the corrosion resistance. This latter was correlated to chromium enrichment (47 wt.%) at the surface of the stainless steel and the induced absence of martensite and ferrite phases. However, these structural and chemical modifications were not sufficient to explain the change in corrosion behaviour: defects and adhesion of the surface oxide layer must have been taken into consideration.

Avaliação do campo de tensões residuais por difração de raios - X utilizando o método do sen²ψ em revestimentos metálicos do aço inoxidável E308-L

Directory of Open Access Journals (Sweden)

Raphael. H. F. Melo

2013-03-01

Full Text Available A aplicação por soldagem de revestimentos metálicos de aços e ligas nobres resistentes à corrosão é uma alternativa bastante razoável economicamente frente à fabricação de componentes maciços nestas ligas. Entretanto há uma carência de informações sobre as alterações mecânico/metalúrgicas causadas pelos ciclos térmicos de soldagem quando da aplicação destes revestimentos, principalmente sobre a influência sobre o nível de tensões residuais , que é mister no entendimento do fenômeno da corrosão assistida por tensão. O objetivo deste trabalho foi avaliar o nível de tensões residuais superficiais em revestimentos do aço inoxidável AWS E308-L T-1 aplicados pelo processo de soldagem ao Arco Elétrico com Arame Tubular sobre chapas do aço ASTM A36. As medições das tensões residuais foram realizadas por um difratômetro portátil de raios - X na superfície dos revestimentos e os principais resultados obtidos foram que a natureza das tensões residuais na superfície dos revestimentos sempre se apresentou compressivas e não observou-se uma linearidade da magnitude das tensões residuais em função da energia de soldagem.

Formation of abrasion-resistant coatings of the AlSiFexMny intermetallic compound type on the AISI 304L alloy

Directory of Open Access Journals (Sweden)

Martínez-Perales, Laura G.

2016-03-01

Full Text Available The α-Al9FeMnSi and β-Al9FeMn2Si intermetallics formed by reactive sintering of Al, Si, Mn, Fe, Cr and Ni powders have been used in AISI 304L steels to enhance microhardness. Processing variables of the reactive sintering treatment were temperature (600, 650, 700, 750 and 800 °C, pressure (5, 10 y 20 MPa and holding time (3600, 5400 y 7200 seconds. Experimental results show that temperature is the most important variable affecting the substrate/coating formation, while pressure does not appear to have a significant effect. The results show the optimum conditions of the reactive sintering that favor the substrate/coating formation are 800 °C, 20 MPa and 7200 seconds. Under these conditions, the reaction zone between the substrate and coating is more compacted and well-adhered, with a microhardness of 1300 Vickers. The results of SEM and X-Ray diffraction confirmed the formation of α-Al9FeMnSi and β-Al9FeMn2Si intermetallics in the substrate/coating interface as well as the presence of Cr and Ni, indicating diffusion of these two elements from the substrate to the interface.Los intermetálicos α-Al9FeMnSi y β-Al9FeMn2Si formados por sinterización reactiva de polvos Al, Si, Mn, Fe, Cr, Ni se han utilizado en aceros AISI 304L para mejorar la microdureza. Las variables de procesamiento de sinterización reactiva fueron temperatura (600, 650, 700, 750, y 800 °C, presión (5, 10 y 20 MPa y el tiempo de retención (3600, 5400 7200 segundos. Los resultados experimentales muestran que la temperatura es la variable más importante que afecta a la formación del sustrato/recubrimiento, mientras que la presión no parece tener un efecto significativo una influencia significativa. Los resultados muestran las condiciones óptimas de la sinterización reactiva que favorecen la formación del sustrato/recubrimiento a 800 °C, 20 MPa y 7200 segundos. En estas condiciones, la zona de reacción entre el sustrato y el recubrimiento es más compacta y bien

9 CFR 381.304 - Operations in the thermal processing area.

Science.gov (United States)

2010-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION POULTRY PRODUCTS INSPECTION REGULATIONS Canning and Canned... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Operations in the thermal processing area. 381.304 Section 381.304 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE...

Caracterización mecánica de recubrimientos de aluminio por CVD-FBR sobre aceros inoxidables y resistencia a la oxidación en vapor de agua

OpenAIRE

Diego Pérez-Muñoz; José Luddey Marulanda-Arévalo; Juan Manuel Meza-Meza

2015-01-01

Los recubrimientos de aluminio depositados sobre el acero inoxidable austenítico AISI 317 por Deposición Química de Vapor en Lecho Fluidizado (CVD-FBR) presentan a altas temperaturas una reducción de la velocidad de corrosión de más de 80 veces. Se realizó la caracterización mecánica de los recubrimientos por medio de microdureza, nanoindentación, para conocer cómo se vieron afectas las propiedades mecánicas (en especial la dureza y el módulo de Young) del recubrimiento y del sustrato luego d...

41 CFR 105-60.304 - Public information handbook and index.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Public information handbook and index. 105-60.304 Section 105-60.304 Public Contracts and Property Management Federal Property... index. GSA publishes a handbook for the public that identifies information regarding any matter...

48 CFR 2015.304 - Evaluation factors.

Science.gov (United States)

2010-10-01

... METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection Processes and Techniques 2015.304... numerically weighted are conflict of interest, estimated cost, and “go/no go” evaluation factors. ...

Studies on mechanical properties, microstructure and fracture morphology details of laser beam welded thick SS304L plates for fusion reactor applications

Energy Technology Data Exchange (ETDEWEB)

Buddu, Ramesh Kumar, E-mail: buddu@ipr.res.in [Fusion Reactor Materials Development and Characterization Division, Institute for Plasma Research, Bhat, Gandhinagar 382428 (India); Chauhan, N.; Raole, P.M. [Fusion Reactor Materials Development and Characterization Division, Institute for Plasma Research, Bhat, Gandhinagar 382428 (India); Natu, Harshad [Magod Laser Machining Pvt. Ltd, Jigani, Bengaluru 560105 (India)

2015-06-15

Highlights: • CO{sub 2} laser welding of 8 mm thick SS304L plates has been carried out and full penetration welds fabricated and characterized for mechanical properties and microstructure details. • Welded samples have shown tensile properties comparable to base indicating good weld quality joints. • Impact fracture tests of weld zone and heat affected zone samples have shown poor toughness compared to the base metal. • SEM analysis of fracture samples of tensile and impact specimens indicated the complex microstructure features in weld zone and combined ductile and brittle fracture features. • Combined features of dendrite and cellular structures are observed in weld microstructures with narrow HAZ and delta ferrite is found in the welds and further confirmed by higher Ferrite Number data. - Abstract: Austenitic stainless steel is widely used structural material for the fabrication of the fusion reactor components. Laser welding is high power density process which offers several advantages over the other conventional processes like Tungsten Inert Gas welding. The features like low distortion, narrow heat affected zone, deep penetration in single pass, good mechanical properties are some of the advantages of laser welding process. The laser weld process parameters optimization has several challenges in terms of overcoming the weld defects like voids due to lack of penetration over depth, undercuts and porosity. The present paper reports the studies carried out with CO{sub 2} laser welding of 8 mm thick austenitic stainless steel SS304L plates and their characterization of mechanical properties, microstructure and fracture morphology details. The weld process parameter optimization towards defect free welds with full penetration welding has been carried out. The welded samples have shown tensile properties comparable to base metal, bend tests are successfully passed. The hardness measurements have shown slightly higher for weld zone compared to base metal

Studies on mechanical properties, microstructure and fracture morphology details of laser beam welded thick SS304L plates for fusion reactor applications

International Nuclear Information System (INIS)

Buddu, Ramesh Kumar; Chauhan, N.; Raole, P.M.; Natu, Harshad

2015-01-01

Highlights: • CO 2 laser welding of 8 mm thick SS304L plates has been carried out and full penetration welds fabricated and characterized for mechanical properties and microstructure details. • Welded samples have shown tensile properties comparable to base indicating good weld quality joints. • Impact fracture tests of weld zone and heat affected zone samples have shown poor toughness compared to the base metal. • SEM analysis of fracture samples of tensile and impact specimens indicated the complex microstructure features in weld zone and combined ductile and brittle fracture features. • Combined features of dendrite and cellular structures are observed in weld microstructures with narrow HAZ and delta ferrite is found in the welds and further confirmed by higher Ferrite Number data. - Abstract: Austenitic stainless steel is widely used structural material for the fabrication of the fusion reactor components. Laser welding is high power density process which offers several advantages over the other conventional processes like Tungsten Inert Gas welding. The features like low distortion, narrow heat affected zone, deep penetration in single pass, good mechanical properties are some of the advantages of laser welding process. The laser weld process parameters optimization has several challenges in terms of overcoming the weld defects like voids due to lack of penetration over depth, undercuts and porosity. The present paper reports the studies carried out with CO 2 laser welding of 8 mm thick austenitic stainless steel SS304L plates and their characterization of mechanical properties, microstructure and fracture morphology details. The weld process parameter optimization towards defect free welds with full penetration welding has been carried out. The welded samples have shown tensile properties comparable to base metal, bend tests are successfully passed. The hardness measurements have shown slightly higher for weld zone compared to base metal and the

Thermo-mechanical treatment for improvement of superplasticity of SUS304; SUS304 no chososei kyodo kaizen no tame no kako netsu shori

Energy Technology Data Exchange (ETDEWEB)

Kato, M.; Torisaka, Y. [Mechanical Engineering Lab., Tokyo (Japan)

1998-01-25

Thermo-mechanical treatment was given to improve further the superplastic behavior of SUS 304 stainless steel. In the SUS 304, martensite phase produced by the processing induced transformation may be reversely transformed to the primary austenite phase by high-temperature heating. Crystal grain size is micronized to 1 {mu} m by combining this reverse transformation and recrystallization of the austenite phase. However, the straining rate at that time is as extremely low as 1 times 10 {sup -4}/s or lower, which is insufficient for an industrial material. Therefore, the SUS 304 processed as described above was given again a series of thermo-mechanical treatment of the similar forced cold processing and annealing to ultra-micronize the crystalline particles. Majority of the crystalline particles have come to have a grain size of several hundred nm. This test piece showed a total elongation of 400% or more at a test temperature of 973 K and a straining rate of 1.8 times 10 {sup -3}/s or lower. In addition, the straining rate sensitivity index `m` at that time was 0.45 or higher. The superplastic deformation of the SUS 304 has a high possibility of being governed by dynamic recrystallization. 4 refs., 7 figs., 1 tab.

48 CFR 304.7100 - Policy.

Science.gov (United States)

2010-10-01

... MATTERS Review and Approval of Proposed Contract Actions 304.7100 Policy. (a) The HCA (non-delegable) shall establish review and approval procedures for proposed contract actions to ensure that— (1) Contractual documents are in conformance with law, established policies and procedures, and sound business...

25 CFR 304.1 - Penalties for imitation or unauthorized use.

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Penalties for imitation or unauthorized use. 304.1... SILVER, USE OF GOVERNMENT MARK § 304.1 Penalties for imitation or unauthorized use. The use of Government trade-marks in an unauthorized manner, or the colorable imitation of such marks, is subject to the...

Anomalous mass transport in Au/304 stainless steel powder under shock loading

Energy Technology Data Exchange (ETDEWEB)

Staudhammer, Karl P.

2004-01-01

Dynamic deformation experiments on gold plated 304L stainless steel powders were undertaken using a axial symmetrical implosion geometry. These experiments utilized pressures of 0.08 to 1.0 Mbar and contained a symmetric radial melt region along the central axis of the sample holder. To understand the role of deformation in a porous material, the pressure, and temperature as well as the deformation heat and associated defects must be accounted for. Using a strain controllable shock loading design it was possible to separate and control independently strain and pressure. Thus enabling the ability to control the added heat from the deformation process undergoing compaction/consolidation of the powder. When the added heat of consolidation deformation exceeds the melt temperature of the 304 powders, a melt zone results that can consume large regions of the compact. It is within these regions that very high diffusion of gold into the powder occurs. These anomalous increases have been observed via optical microscopy, scanning electron microscopy and EDAX measurements. Values exceeding 1200 m/sec have been measured and correlated to the powder sizes, size distribution and packing density, concomitant with sample container strains ranging from 2.0% to 26%.

Characterization and study of mechanical and tribological properties on titanium di oxide (TiO2) coated 304L stainless steel

Science.gov (United States)

Ghanaraja, S.; Ali, Syed Imran; Ravikumar, K. S.; Likith, P.

2018-04-01

In the present investigation Atmospheric Plasma Spraying (APS) method is selected for coating the materials on 304L Stainless Steel as a substrate material, also called as substrate of Thermal Barrier Coating (TBC) system developed in the present work. Commercially available Ni-Cr metal powder is selected for bond coat and TiO2 powder is selected for Top Coat. The thickness of bond coat is taken as 75 µm where as the top coat thickness is varied as 100 µm, 200 µm and 300 µm. In plasma sprayed coating more attention is given to obtain uniform thickness on the given substrate. The various surface texture parameters of each sample is tested, morphology and coating thickness of above TBC system are studied with the help of SEM and X-Ray Diffraction for phase analysis. Micro-hardness of each layer of coating is measured by using Vicker's diamond indentation and the abrasive wear resistance of each system has been investigated through Pin-on-disc test, at room temperature by using wear and friction tribometer. The coating system possesses good wear resistance and can be used in various applications.

Characterization of welding of AISI 304l stainless steel similar to the core encircling of a BWR reactor

International Nuclear Information System (INIS)

Gachuz M, M.E.; Palacios P, F.; Robles P, E.F.

2003-01-01

Plates of austenitic stainless steel AISI 304l of 0.0381 m thickness were welded by means of the SMAW process according to that recommended in the Section 9 of the ASME Code, so that it was reproduced the welding process used to assemble the encircling of the core of a BWR/5 reactor similar to that of the Laguna Verde Nucleo electric plant, there being generated the necessary documentation for the qualification of the one welding procedure and of the welder. They were characterized so much the one base metal, as the welding cord by means of metallographic techniques, scanning electron microscopy, X-ray diffraction, mechanical essays and fracture mechanics. From the obtained results it highlights the presence of an area affected by the heat of up to 1.5 mm of wide and a value of fracture tenacity (J IC ) to ambient temperature for the base metal of 528 KJ/m 2 , which is diminished by the presence of the welding and by the increment in the temperature of the one essay. Also it was carried out an fractographic analysis of the fracture zone generated by the tenacity essays, what evidence a ductile fracture. The experimental values of resistance and tenacity are important for the study of the structural integrity of the encircling one of the core. (Author)

Effect of martensitic phase transformation on the hardening behavior and texture evolution in a 304L stainless steel under compression at liquid nitrogen temperature

Energy Technology Data Exchange (ETDEWEB)

Cakmak, Ercan [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States); Vogel, Sven C. [Los Alamos Neutron Science Center, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Choo, Hahn, E-mail: hchoo@utk.edu [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States)

2014-01-01

The martensitic phase transformation behavior and its relations with the macroscopic hardening rate and the evolutions in the crystallographic texture of the constituent phases were studied for a 304L stainless steel that exhibits the transformation induced plasticity (TRIP) phenomenon. Time-of-flight neutron diffraction was used to measure the evolutions of phase fractions and texture in terms of pole figures as a function of the applied compressive strain at the liquid nitrogen temperature (77 K). The phase transformation analyses show that the hcp-martensite phase fraction reaches a significant level of about 22 wt% at 15% applied strain and remains constant. The bcc-martensite phase fraction increases continuously with the deformation that correlates well with the macroscopic hardening behavior. Furthermore, the texture analyses show that transformation has dominant effect on the bcc-martensite texture evolution with little influence from subsequent plastic deformation at current testing conditions.

Effect of martensitic phase transformation on the hardening behavior and texture evolution in a 304L stainless steel under compression at liquid nitrogen temperature

International Nuclear Information System (INIS)

Cakmak, Ercan; Vogel, Sven C.; Choo, Hahn

2014-01-01

The martensitic phase transformation behavior and its relations with the macroscopic hardening rate and the evolutions in the crystallographic texture of the constituent phases were studied for a 304L stainless steel that exhibits the transformation induced plasticity (TRIP) phenomenon. Time-of-flight neutron diffraction was used to measure the evolutions of phase fractions and texture in terms of pole figures as a function of the applied compressive strain at the liquid nitrogen temperature (77 K). The phase transformation analyses show that the hcp-martensite phase fraction reaches a significant level of about 22 wt% at 15% applied strain and remains constant. The bcc-martensite phase fraction increases continuously with the deformation that correlates well with the macroscopic hardening behavior. Furthermore, the texture analyses show that transformation has dominant effect on the bcc-martensite texture evolution with little influence from subsequent plastic deformation at current testing conditions

48 CFR 227.304-1 - General.

Science.gov (United States)

2010-10-01

... Contracts 227.304-1 General. Interim and final invention reports and notification of all subcontracts for... of Inventions and Subcontracts. [56 FR 36389, July 31, 1991, as amended at 57 FR 53600, Nov. 12, 1992] ...

Avaliação do coeficiente de atrito de braquetes metálicos e estéticos com fios de aço inoxidável e beta-titânio Evaluation of the friction coefficient of metal and esthetic brackets with stainless steel and beta-titanium wires

Directory of Open Access Journals (Sweden)

Cristine Pritsch Braga

2004-12-01

Full Text Available Um fator importante que define a eficácia dos aparelhos ortodônticos fixos é o atrito existente entre as superfícies de fios e braquetes. Assim, este estudo teve como objetivo investigar o coeficiente de atrito estático entre fios de aço inoxidável e beta-titânio (TP Orthodontics e braquetes de aço inoxidável (Dynalock® - Unitek, braquetes estéticos com slot de aço inoxidável (Clarity® - Unitek e estéticos convencionais (Allure® - GAC. Para tanto, construiu-se um equipamento no Departamento de Engenharia Mecânica e Mecatrônica da PUCRS. Antes de serem iniciados os testes, foi quantificado o erro de método e constatou-se que não houve interferência significante (p>0,05 do fator operador nas medições. Então, pôde-se calcular o valor do coeficiente de atrito, obtido pela divisão da força de atrito pela carga normal. O método estatístico utilizado neste estudo foi Análise de Variância (ANOVA e teste de Comparações Múltiplas (Tukey. Constatou-se que: 1 a combinação com menor coeficiente de atrito foi composta pelo fio de aço inoxidável e braquete Dynalock® e a que apresentou maior coeficiente foi a do braquete Allure® com o fio de beta-titânio; 2 o fio de beta-titânio apresentou coeficiente de atrito significativamente maior do que o fio de aço inoxidável; 3 o braquete Dynalock® não apresentou diferenças significativas em relação ao coeficiente de atrito do braquete Clarity® quando o fio utilizado foi de beta-titânio. No entanto, quando o fio testado foi de aço inoxidável, apresentou coeficiente de atrito significativamente menor. O braquete Clarity® apresentou coeficiente de atrito significativamente menor do que o braquete Allure®.An important factor that defines the effectiveness of the appliances is the friction between the surfaces of wires and brackets. Thus, that study was developed in order to investigate the static friction coefficient between stainless steel and beta-titanium wires (TP

Some pitfalls in welding of duplex stainless steels Algumas armadilhas na soldagem de aços inoxidáveis duplex

Directory of Open Access Journals (Sweden)

Demian J. Kotecki

2010-12-01

Full Text Available Duplex stainless steels (DSS, including super duplex stainless steels {SDSS} have proven to be very useful engineering materials, albeit with somewhat different welding requirements than those of the more familiar austenitic stainless steels. Despite a generally good track record in welding of duplex stainless steels, certain pitfalls have been encountered with enough frequency that they deserve review. Inappropriate base metal specification often leads to unsuitable heat affected zone (HAZ properties. Autogenous fusion zones are also of concern. This issue centers around nitrogen limits. The most frequently encountered is applying the UNS S31803 composition for 2205 DSS, instead of the S32205 composition. Inappropriate welding heat input arises most frequently with SDSS. While 0.5 to 1.5 kJ/mm is a normal heat input recommendation for SDSS, either a root pass or many small beads towards the low end of this heat input range tends to result in precipitation and/or secondary austenite formation in weld metal subjected to repeated thermal cycles from multiple weld passes. Inappropriate PWHT occurs when the enhanced nickel filler metals (typically 9% Ni are used. DSS are not normally given PWHT, but extensive forming of heads, for example, or repair welding of castings, may require a postweld anneal. Specifications such as ASTM A790 and A890 call for annealing at 1040ºC minimum, and the fabricator tends to use temperatures close to that minimum. However, the enhanced nickel filler metals require higher temperatures to dissolve sigma phase that forms during heating to the annealing temperature.Aços inoxidáveis duplex (AID, incluindo os aços super duplex, AISD provaram ser materiais de engenharia muito úteis, embora com requerimentos de soldagem em alguma medida diferentes daqueles dos aços inoxidáveis austeníticos mais usuais. Apesar do histórico geralmente bom dos aços inoxidáveis duplex quanto a soldagem, algumas dificuldades têm sido

Resistência à corrosão de aços inoxidáveis em solução sintética de condensado de álcool combustível

OpenAIRE

Menezes, Marcela Rabelo

2010-01-01

A necessidade de atender as exigências impostas por órgãos ambientais no que se refere à emissão de poluentes gasosos e à demanda dos consumidores por veículos mais econômicos e mais duráveis, principalmente no que diz respeito à maior resistência à corrosão, tem promovido pesquisas para a substituição de materiais tradicionais nos sistemas de exaustão de veículos procurando atingir um custo-benefício favorável. Nesse contexto estão inseridos os aços inoxidáveis que têm elevadas resistência m...

41 CFR 304-2.1 - What definitions apply to this chapter?

Science.gov (United States)

2010-07-01

... title, the Foreign Affairs Manual (FAM), and the Joint Travel Regulations (JTR) for transportation, food... to this chapter? 304-2.1 Section 304-2.1 Public Contracts and Property Management Federal Travel Regulation System PAYMENT OF TRAVEL EXPENSES FROM A NON-FEDERAL SOURCE EMPLOYEE'S ACCEPTANCE OF PAYMENT FROM...

5 CFR 9701.304 - Definitions.

Science.gov (United States)

2010-01-01

... performance expectations (as defined in § 9701.404) over the applicable period; or (2) To support a pay... MANAGEMENT SYSTEM Pay and Pay Administration General § 9701.304 Definitions. In this part: 48 contiguous... Columbia. Band means a work level or pay range within an occupational cluster. Band rate range means the...

41 CFR 304-6.8 - Will the reports be made available for public inspection?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 4 2010-07-01 2010-07-01 false Will the reports be made available for public inspection? 304-6.8 Section 304-6.8 Public Contracts and Property Management Federal...-PAYMENT GUIDELINES Valuation § 304-6.8 Will the reports be made available for public inspection? Yes, OGE...

Desenvolvimento da ferrita delta na solda e ZTA resultante de soldagem plasma pulsada em um aço inoxidável supermartensítico Delta-ferrite development in weld and HAZ produced by pulsed plasma arc welding in a supermartensitic stainless steel

Directory of Open Access Journals (Sweden)

Sérgio L. Henke

2013-03-01

Full Text Available A ferrita delta é considerada uma fase indesejável na microestrutura dos aços inoxidáveis martensíticos haja vista a mesma poder influenciar no desempenho da resistência à fadiga, tenacidade e corrosão sob-tensão. Sendo assim, o objetivo deste trabalho foi investigar o efeito da soldagem plasma pulsada sobre a distribuição e quantidade de ferrita delta em um aço inoxidável supermartensítico. Para tal foram obtidos cordões por meio de fusão superficial sobre uma amostra de aço inoxidável supermartensítico de alta liga utilizando corrente pulsada e convencional. Em seguida foi efetuada a caracterização microestrutural, em especial da ferrita delta, via análises metalográficas por meio de microscopia óptica e eletrônica de varredura . Os experimentos revelaram que, para o mesmo aporte térmico, a pulsação de corrente promoveu a formação de ferrita delta na forma de bandas ao longo do cordão de solda e redução significativa desta fase na ZTA quando comparada à soldagem convencional.The objective of this study was to investigate the effect of pulsed plasma welding on the distribution and amount of delta ferrite which is considered an undesirable phase in a supermartensitic stainless steel. For such weld beads have been obtained by melting the surface of a sample of a high-alloy supermartensitic stainless steel using pulsed and conventional current. Microstructural characterization, especially of delta ferrite, was performed by metallographic analysis by means of optical microscopy and scanning electron microscopy. The experiments showed that for the same heat input, pulsed current promoted the formation of delta ferrite in the form of bands along the weld bead and caused a significant reduction of this phase in HAZ as compared to conventional welding.

Exploring He II 304 Å Spicules and Macrospicules at the Solar Limb

Science.gov (United States)

Sterling, A. C.; Snyder, I. R.; Falconer, D. A.; Moore, R. L.

2014-12-01

We present results from a study of He II 304 Ang spicules and macrospiculesobserved at the limb of the Sun in 304 Ang channel image sequences from theAtmospheric Imaging Assembly (AIA) on the Solar Dynamics Observatory (SDO). Thesedata have both high spatial (0.6 arcsec pixels) and temporal (12 s) resolution. All of the observed events occurred in quiet or coronal hole regions near the solarpole. He II 304 Ang spicules and macrospicules are both transient jet-likefeatures, with the macrospicules being wider and having taller maximum heights thanthe spicules. We looked for characteristics of the populations of these twophenomena that might indicate whether they have the same initiation mechanisms. Weexamine the maximum heights, time-averaged rise velocities, and lifetimes of about30 spicules and about five macrospicules. For the spicules, these quantities are,respectively, ~10,000----40,000 km, 20---100 km/s, and a few 100--- ~600 sec. Forthe macrospicules the corresponding properties are >~60,000 km, >~55 km/s, andlifetimes of >~1800 sec. Therefore the macrospicules have velocities comparable tothose of the fastest spicules and live longer than the spicules. The leading-edgetrajectories of both the spicules and the macrospicules match well a second-order(``parabolic'') profile, although the acceleration in the fitted profiles is generally weaker than that of solar gravity. The macrospicules also have obviousbrightenings at their bases at their birth, while such brightenings are notapparent for most of the spicules. Our findings are suggestive of the twophenomena possibly having different initiation mechanisms, but this is not yetconclusive. A.C.S. and R.L.M. were supported by funding from the HeliophysicsDivision of NASA's Science Mission Directorate through the Living With a StarTargeted Research and Technology Program, and the Hinode Project. I.R.S. wassupported by NSF's Research Experience for Undergraduates Program.

47 CFR 0.304 - Authority for determinations of exempt telecommunications company status.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Authority for determinations of exempt telecommunications company status. 0.304 Section 0.304 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL... determinations of exempt telecommunications company status. Authority is delegated to the Chief, Wireline...

Fricção em braquetes gerada por fios de aço inoxidável, superelásticos com IonGuard e sem IonGuard Friction force on brackets generated by stainless steel wire and superelastic wires with and without IonGuard

Directory of Open Access Journals (Sweden)

Luiz Carlos Campos Braga

2011-08-01

Full Text Available OBJETIVO: o objetivo deste estudo foi verificar a fricção no braquete (Roth, Composite, 10.17.005, 3,2mm, largura 0,022" x 0,030", Torque -2° e angulação +13°, Morelli®, Brasil, utilizando fios ortodônticos retangulares de 0,019" x 0,025" de aço inoxidável (Morelli®, Brasil e de níquel-titânio superelásticos Bioforce com IonGuard e sem IonGuard (Bioforce, GAC®, EUA. MÉTODOS: foram utilizados 24 conjuntos braquetes/segmento de fio, divididos em 3 grupos de acordo com o fio. Cada conjunto braquete/segmento de fio foi testado 3 vezes e obtida uma média. Os ensaios foram realizados em máquina universal de ensaios EMIC DL2000®. Os dados foram submetidos à Análise de Variância com significância de 95%. RESULTADOS: o fio retangular Bioforce com IonGuard apresentou fricção significativamente menor que o Bioforce sem IonGuard, porém sem diferença do fio de aço inoxidável. Entretanto, o coeficiente de variação dos fios Bioforce com e sem IonGuard foi menor que o do fio de aço inoxidável. CONCLUSÃO: os fios retangulares de 0,019" x 0,025" Bioforce com IonGuard apresentam menor fricção que o fio Bioforce sem IonGuard, sem diferença para o fio de aço inoxidável.OBJECTIVE: The aim of this study was to evaluate the friction forces on brackets (Roth, Composite, 10.17.005, 3.2 mm, width 0.022" x 0.030 ", Torque -2° and angulation +13°, Morelli®, Brazil, with stainless steel orthodontic rectangular wire (Morelli®, Brazil and nickel titanium superelastic Bioforce wires with and without IonGuard (Bioforce, GAC®, USA. MATERIAL AND METHODS: Twenty-four brackets/wire segment combinations were used, distributed into three groups according to the orthodontic wire. Each bracket/wire segment combination was tested three times. The tests were performed in a universal testing machine Emic DL2000®. The data was submitted to ANOVA one way followed by Tukey's post hoc test (p<0.05. RESULTS: The rectangular orthodontic Bioforce wire

Nitrocarburación mediante el proceso TENIFER QDQ de aceros inoxidables austeníticos estabilizados : caracterización química y estudio de su comportamiento frente al desgaste y la corrosión

OpenAIRE

Bellas Muiño, Leonardo

2016-01-01

[Resumen]La nitrocarburación en baño de sales se utiliza para mejorar las propiedades tribológicas de los aceros inoxidables. Sin embargo, la aparición de carburos y nitruros de elementos de aleación en la capa externa puede tener efectos contraproducentes para su resistencia a la corrosión. Por este motivo, el proceso TENIFER®QPQ introduce una etapa de oxidación a altas temperaturas con objeto de formar una capa de magnetita (Fe3O4) que incrementa la resistencia a la corrosión...

Efecto de las variables del procedimiento de soldadura sobre las propiedades mecánicas y la resistencia a la corrosión en depósitos de soldadura de aceros inoxidables supermartensíticos

OpenAIRE

Zappa, Sebastián

2011-01-01

La soldadura de los aceros inoxidables martensíticos ha presentado ciertas dificultades y el uso de tratamientos térmicos es normalmente obligatorio. Las razones son diferentes para cada grado de acero, pero en general, es común obtener alta dureza y baja tenacidad en la zona afectada por el calor. Este hecho está asociado con la estructura martensítica en sí misma y el contenido de carbono. Una posible solución a este problema y para alcanzar determinadas propiedades en condición como soldad...

Fatigue Crack Behavior of Stainless Steel 304 by the Addition of Carbon Nanotubes

Directory of Open Access Journals (Sweden)

Rizwanulhaque Syed

2014-01-01

Full Text Available Fatigue is the main source of almost half of whole mechanical failures. This research investigated the effect on cyclic fatigue behavior of stainless steel 304 (SS304 when including carbon nanotubes (CNTs at the crack tip. The cyclic fatigue tests were conducted on compact tension (CT specimens to establish the relationship between crack growth and the number of cycles (a-N. It is found that the incorporation of a small amount of CNTs increased the fatigue life of the SS304/metal. Micrographs showed that the enhancement in fatigue life is caused by CNTs dense arrangement around the crack tip, entangled with each other, and finer grain size. Smooth bonding at the interface of the CNTs and SS304 grains is also observed.

Functionally graded material of 304L stainless steel and inconel 625 fabricated by directed energy deposition: Characterization and thermodynamic modeling

International Nuclear Information System (INIS)

Carroll, Beth E.; Otis, Richard A.; Borgonia, John Paul; Suh, Jong-ook; Dillon, R. Peter; Shapiro, Andrew A.; Hofmann, Douglas C.; Liu, Zi-Kui; Beese, Allison M.

2016-01-01

Many engineering applications, particularly in extreme environments, require components with properties that vary with location in the part. Functionally graded materials (FGMs), which possess gradients in properties such as hardness or density, are a potential solution to address these requirements. The laser-based additive manufacturing process of directed energy deposition (DED) can be used to fabricate metallic parts with a gradient in composition by adjusting the volume fraction of metallic powders delivered to the melt pool as a function of position. As this is a fusion process, secondary phases may develop in the gradient zone during solidification that can result in undesirable properties in the part. This work describes experimental and thermodynamic studies of a component built from 304L stainless steel incrementally graded to Inconel 625. The microstructure, chemistry, phase composition, and microhardness as a function of position were characterized by microscopy, energy dispersive spectroscopy, X-ray diffraction, and microindentation. Particles of secondary phases were found in small amounts within cracks in the gradient zone. These were ascertained to consist of transition metal carbides by experimental results and thermodynamic calculations. The study provides a combined experimental and thermodynamic computational modeling approach toward the fabrication and evaluation of a functionally graded material made by DED additive manufacturing.

Influência do nitrogênio adicionado por SHTPN na resistência à erosão por cavitação do aço inoxidável martensítico

OpenAIRE

Maftoum, Ricardo de Almeida

2013-01-01

Muitos estudos são realizados para melhorar a resistência à erosão por cavitação dos aços. Entre estes estudos, está a utilização de aços inoxidáveis enriquecidos com nitrogênio na superfície. O presente trabalho estudou o uso da técnica SHTPN (Solution Heat Treatment after Plasma Nitriding), que consiste em duas etapas. Primeiro utiliza-se a nitretação a plasma, para inserir o nitrogênio no material. Na sequência realiza-se o tratamento térmico de solubilização, para que o nitrogênio fique e...

Nucleation and growth microstructural study of ti films on 304 SS substrates

Directory of Open Access Journals (Sweden)

Rogério de Almeida Vieira

2004-09-01

Full Text Available Coating of steel surfaces with titanium films has been studied with the objective to protect them against corrosion, and to create an intermediate film for CVD diamond and TiN film deposition. In this work, the nucleation, growth mechanisms and microstructural formation of the titanium films deposited on 304 stainless steel (304 SS substrate are presented and discussed. The titanium films of variable thickness were obtained by vapour phase deposition produced by electron beam. The surfaces of these samples were observed by scanning electron microscopy. The cross sections of these samples were observed by using an atomic force microscope. The Ti film-304 SS interfaces were analyzed by X-ray diffraction. The results showed that titanium films have a columnar growth. The Ti film-304 SS interface had a residual compression stress at room temperature due to the inter-diffusion process.

7 CFR 51.304 - Combination grades.

Science.gov (United States)

2010-01-01

... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946... Standards for Grades of Apples Grades § 51.304 Combination grades. (a) Combinations of the above grades may...

Anaerobic Corrosion of 304 Stainless Steel Caused by the Pseudomonas aeruginosa Biofilm

Directory of Open Access Journals (Sweden)

Ru Jia

2017-11-01

Full Text Available Pseudomonas aeruginosa is a ubiquitous bacterium capable of forming problematic biofilms in many environments. They cause biocorrosion of medical implants and industrial equipment and infrastructure. Aerobic corrosion of P. aeruginosa against stainless steels has been reported by some researchers while there is a lack of reports on anaerobic P. aeruginosa corrosion in the literature. In this work, the corrosion by a wild-type P. aeruginosa (strain PAO1 biofilm against 304 stainless steel (304 SS was investigated under strictly anaerobic condition for up to 14 days. The anaerobic corrosion of 304 SS by P. aeruginosa was reported for the first time. Results showed that the average sessile cell counts on 304 SS coupons after 7- and 14-day incubations were 4.8 × 107 and 6.2 × 107 cells/cm2, respectively. Scanning electron microscopy and confocal laser scanning microscopy corroborated the sessile cell counts. The X-ray diffraction analysis identified the corrosion product as iron nitride, confirming that the corrosion was caused by the nitrate reducing biofilm. The largest pit depths on 304 SS surfaces after the 7- and 14-day incubations with P. aeruginosa were 3.9 and 7.4 μm, respectively. Electrochemical tests corroborated the pitting data.

Influence of microstructure on the microbial corrosión behaviour of stainless steels

Directory of Open Access Journals (Sweden)

Moreno, Diego Alejandro

2000-08-01

(EDX. En cada estado microestructural estudiado se han observado diferentes comportamientos en relación con su resistencia a la corrosión microbiana. Los aceros inoxidables austeníticos sensibilizados fueron más afectados por la presencia de aniones agresivos y los valores del potencial de picadura (Ep fueron más catódicos que en estado de recepción. Así mismo, se produce un incremento de la corrosión por la acción sinérgica entre los aniones cloruros y los sulfuros biogénicos. Se ha encontrado, en uno de los ensayos de biocorrosión, picaduras en el acero inoxidable martensítico del tipo UNS S42000. Se correlaciona la morfología observada en las picaduras con la composición química, la microestructura y el electrólito.

“MEDICION DE PARAMETROS GENERADORES DE ESFUERZOS RESIDUALES DURANTE EL PROCESO DE SOLDADURA DE ACERO INOXIDABLE AUSTENITICO AISI 304L”.

OpenAIRE

García López, Christian Jesus

2012-01-01

En la actualidad los procesos de soldadura por arco eléctrico se han convertido en la técnica por excelencia para la unión del acero y sus aleaciones. Se puede mencionar que la importancia de la soldadura, es tal, que sin ella no serían posibles muchos de los productos y servicios que cotidianamente son consumidos o requeridos por las sociedades contemporáneas actuales. Cada vez con mayor longitud y diámetro se instalan líneas de tubería para la distribución y conducción de tod...

Hardness Enhancement of STS304 Deposited with Yttria Stabilized Zirconia by Aerosol Deposition Method

Energy Technology Data Exchange (ETDEWEB)

Lim, Il-Ho; Park, Chun-Kil; Kim, Hyung Sun; Jeong, Dea-Yong [Inha University, Incheon (Korea, Republic of); Lee, Yong-Seok [Sodoyeon Co., Yeoju (Korea, Republic of); Kong, Young-Min [University of Ulsan, Ulsan (Korea, Republic of); Kang, Kweon Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-03-15

To improve the surface hardness of the STS304, Yttria stabilized zirconia (YSZ) films with nano-sized grain were deposited by an aerosol-deposition (AD) method. Coating layers showed dense structure and had -5µm thickness. When 3 mol% YSZ powders with tetragonal phase were deposited on STS304 substrate, tetragonal structure was transformed to cubic structure due to the high impact energy during the AD process. At the same time, strong impact by YSZ particles allowed the austenite phase in STS304 to be transformed into martensite phase. Surface hardness measured with nano indentor showed that YSZ coated film had 11.5 GPa, which is larger value than 7 GPa of STS304.

10 CFR 2.304 - Formal requirements for documents; signatures; acceptance for filing.

Science.gov (United States)

2010-01-01

... through the E-Filing system written testimony or hearing exhibits in advance of a hearing, the written... for filing. 2.304 Section 2.304 Energy NUCLEAR REGULATORY COMMISSION RULES OF PRACTICE FOR DOMESTIC...; signatures; acceptance for filing. (a) Docket numbers and titles. Each document filed in an adjudication to...

41 CFR 301-71.304 - Are we responsible for ensuring the collection of outstanding travel advances?

Science.gov (United States)

2010-07-01

... ensuring the collection of outstanding travel advances? 301-71.304 Section 301-71.304 Public Contracts and Property Management Federal Travel Regulation System TEMPORARY DUTY (TDY) TRAVEL ALLOWANCES AGENCY RESPONSIBILITIES 71-AGENCY TRAVEL ACCOUNTABILITY REQUIREMENTS Accounting for Travel Advances § 301-71.304 Are we...

Soldagem de um aço inoxidável ferrítico com o processo A-TIG Ferritic stainless steel welding with the A-TIG process

Directory of Open Access Journals (Sweden)

Alessandra Gois Luciano de Azevedo

2009-03-01

Full Text Available O processo de soldagem TIG com fluxo (processo A-TIG apresenta como principal vantagem a possibilidade de se obter uma maior penetração do cordão de solda empregando os mesmos parâmetros de soldagem do processo TIG convencional. Diversos estudos mostram a influência dos fluxos ativos sobre as características geométricas das soldas em aços inoxidáveis austeníticos, porém pouco se sabe sobre a influência deste processo nas características geométricas e metalúrgicas de cordões de solda em aços inoxidáveis ferríticos. Neste trabalho são aplicados diferentes tipos de fluxo na soldagem de aço inoxidável ferrítico com o objetivo de verificar possíveis influências no perfil do cordão de solda, no seu aspecto visual, na microestrutura, na dureza da zona fundida e na resistência ao impacto (ensaio Charpy. As soldagens "bead-on-plate" foram realizadas sem metal de adição. Foram utilizados seis tipos de fluxo, sendo um óxido elaborado em laboratório (TiO2 e cinco fluxos comerciais. Os resultados mostraram que a utilização do fluxo permite um aumento na penetração com mudanças significativas no aspecto do cordão de solda. Verificou-se ainda que a microestrutura e a dureza do cordão de solda do aço estudado não foram afetadas pelo tipo de fluxo utilizado, com a microestrutura analisada em microscópio óptico. O aço em estudo mostrou um alto grau de fragilidade à temperatura ambiente.The A-TIG welding process presents as main advantage the possibility of increase in the penetration depth using the same parameters as conventional TIG welding. Many researchers show the influence of the active flux on the weld geometry in austenitic stainless steel, however little it is known of the influence of this process in the weld fillet shape and metallurgic characteristics of the weld fillet in ferritic stainless steel. In this work different types of flux are applied with the objective to verify possible influences on the weld

CdTe/TiO{sub 2} nanocomposite material for photogenerated cathodic protection of 304 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiu-tong, E-mail: xiutongwang@gmail.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China); Wei, Qin-yi, E-mail: weiqiny200@163.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China); University of Chinese Academy of Sciences, 19 (Jia) Yuquan Road, Beijing 100049 (China); Zhang, Liang, E-mail: zzll20081988@126.com [CNOOC Information Technology co., Ltd. Beijing Branch, Beijing 100029 China (China); Sun, Hao-fen, E-mail: fyqfyx@163.com [School of Environmental and Municipal Engineering Qingdao, Qingdao Technological University, Qingdao 266033 China (China); Li, Hong, E-mail: lhqdio1987@163.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China); Zhang, Qiao-xia, E-mail: qiaoxiazhang1989@163.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China)

2016-06-15

Graphical abstract: - Highlights: • The photoelectric properties of TiO{sub 2} could greatly improve by doping with CdTe. • The cathodic protection property of the CdTe/TiO{sub 2} was superior to that of pure TiO{sub 2}. • The protective action of the CdTe/TiO{sub 2} for 304SS could be maintained in the dark. - Abstract: TiO{sub 2} nanotubes were fabricated by the anodization method, and CdTe was deposited on them via electrochemical deposition method. The optimal performance of the CdTe/TiO{sub 2} composites was achieved via changing the acidity of the electrolyte. Scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction were used to investigate the surface morphology, elemental analysis and phase characteristics of the composite materials. Some electrochemical tests, such as open-circuit potential, current variation versus time were carried out to investigate the photogenerated cathodic protection of 304 stainless steel by CdTe/TiO{sub 2}. The results indicated that the cathodic protection performance of the CdTe/TiO{sub 2} composite was superior to that of pure TiO{sub 2} in the wavelength of visible light. The CdTe/TiO{sub 2} composite exhibited optimal photogenerated cathodic protection properties under visible light for the corrosion potential of 304 stainless steel shifted negatively to −850 mV when the concentration of HCl in the deposition electrolyte was 1 mol/L.

Corrosion under stress of AISI 304 steel in thiocyanate solutions

International Nuclear Information System (INIS)

Perillo, P.M.; Duffo, G.S.

1989-01-01

Corrosion susceptibility under stress of AISI 304 steel sensitized in a sodium thiocyanate solution has been studied and results were compared with those obtained with solutions of thiosulfate and tetrathionate. Sensitized steel type 304 is highly susceptible to corrosion when under intergranular stress (IGSCC) in thiocyanate solutions but the aggressiveness of this anion is less than that of the other sulphur anions studied (thiosulfate and tetrathionate). This work has been partly carried out in the Chemistry Department. (Author) [es

31 CFR 595.304 - Foreign person.

Science.gov (United States)

2010-07-01

... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY TERRORISM SANCTIONS REGULATIONS General Definitions § 595.304 Foreign person. The term foreign person means any citizen or national of a foreign state (including any such individual who is also a citizen or national of the United States), or any entity not...

Teste intradérmico com proteínas recombinantes de Mycobacterium bovis como antígenos em Cavia porcellus

Directory of Open Access Journals (Sweden)

Elaine S.P. Melo

2014-10-01

Full Text Available O teste intradérmico para o diagnóstico da tuberculose bovina utiliza derivados proteicos purificados (PPD de Mycobacterium bovis que são capazes de induzir reações de hipersensibilidade em animais infectados. No entanto, apresenta baixa especificidade devido à ocorrência de reações cruzadas com outras micobactérias. Neste sentido, o objetivo desse trabalho foi produzir proteínas recombinantes (ESAT-6, PE13, PE5 e ESX-1 de Mycobacterium bovis e avaliá-las como antígenos em teste intradérmico utilizando Cavia porcellus como modelo, e verificar se as condições empregadas na purificação (nativa ou desnaturante interferem no desempenho antigênico dessas proteínas. As proteínas foram testadas em Cavia porcellus previamente sensibilizados com cepa M. bovis AN5 inativada, individualmente (160 µg ou combinadas na forma de um coquetel (40 µg cada. O coquetel de proteínas induziu reações de hipersensibilidade nos animais sensibilizados significativamente superiores (p=0,002 as observadas nos animais não sensibilizados, possibilitando diferenciação. No entanto, as proteínas isoladamente não foram capazes de promover essa diferenciação. As condições de solubilização e purificação influenciaram o desempenho antigênico da proteína ESAT-6, pois, quando produzida em condição desnaturante desencadeou reações inespecíficas nos animais não sensibilizados, enquanto que aquela produzida em condições nativas e aplicada em concentrações de 6, 12, 24 e 48µg induziu reações significativas apenas nos animais sensibilizados, confirmando o seu potencial como antígeno.

31 CFR 594.304 - Foreign person.

Science.gov (United States)

2010-07-01

... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY GLOBAL TERRORISM SANCTIONS REGULATIONS General Definitions § 594.304 Foreign person. The term foreign person means any citizen or national of a foreign state (including any such individual who is also a citizen or national of the United States), or any entity not...

5 CFR 880.304 - FEGLI coverage.

Science.gov (United States)

2010-01-01

... under § 880.205, FEGLI premiums and benefits will be computed using the date of death established under...) RETIREMENT AND INSURANCE BENEFITS DURING PERIODS OF UNEXPLAINED ABSENCE Continuation of Benefits § 880.304 FEGLI coverage. (a) FEGLI premiums will not be collected during periods when an annuitant is a missing...

Fertilization failure after IVF in 304 couples

DEFF Research Database (Denmark)

Krog, Maria; Prior, Maria; Carlsen, Elisabeth

2015-01-01

OBJECTIVES: To identify predictors of total fertilization failure (TFF) and thereby optimize the primary allocation of patients with no well-defined male factor to either IVF or intracytoplasmatic sperm injection (ICSI). Further, to evaluate the long-term fertility prognosis of couples experiencing...... TFF. STUDY DESIGN: A retrospective case-control study including 304 couples with TFF and 304 controls with fertilization after IVF during a 10-year period from year 2000-2010. The controls were the patients with minimum one fertilized oocyte just prior to the cases. Multiple logistic regression...... analysis was used to evaluate the predictors of TFF. RESULTS: The multiple regression analysis identified the following independent predictors of TFF: female smoking, adjusted odds ratio (AOR) 1.7 (95% CI 1.1-2.3), non-tubal factor AOR 2.2 (95% CI 1.5-3.4), progressive motile spermatozoa after preparation...

Prevention of Crevice Corrosion of STS 304 Stainless Steel by a Mg-alloy Galvanic Anode

International Nuclear Information System (INIS)

Lim, U. J.; Yun, B. D.; Kim, J. J.

2006-01-01

Prevention of crevice corrosion was studied for STS 304 stainless steel using a Mg-alloy galvanic anode in solutions with various specific resistivity. The crevice corrosion and corrosion protection characteristics of the steel was investigated by the electrochemical polarization and galvanic corrosion tests. Experimental results show that the crevice corrosion of STS 304 stainless steel does not occur in solutions of high specific resistivity, but it occurs in solutions of low specific resistivity like in solutions with resistivities of 30, 60 and 115 Ω · m. With decreasing specific resistivity of the solution, the electrode potential of STS 304 stainless steel in the crevice is lowered. The potential of STS 304 stainless steel in the crevice after coupling is cathodically polarized more by decreasing specific resistivity indicating that the crevice corrosion of STS 304 stainless steel is prevented by the Mg-alloy galvanic anode

Recubrimiento de Stellite 6 sobre acero inoxidable realizado con láser de CO₂ para válvulas de escape de motores diesel

Directory of Open Access Journals (Sweden)

Cadenas, M.

2002-12-01

Full Text Available To reduce the recovery or the replacement costs of diesel engine exhaust valves, they are manufactured with an economic base material, and a coating which is deposited on the seat valve in order to reach high hardness and good impact, corrosion and high temperature wear resistance (>550 °C and without lubrication. In this work, appropriate laser cladding parameters have been determined to obtain Stellite 6 coatings over AISI 304 steel (as plane test specimens and SAE EV8 steel (as valves substrates. One and two superimposed tracks were deposited on the seat valves, and modifying the laser power as a function of the rotated angle at the beginning and the end of the circular tracks, pores and cracks have been minimized and the thickness of the track were made uniform. Hardness, dilution and final microstructure of the different coatings have been analysed. A 10 % dilution and 550 HV in the tracks over plane test specimens was observed, while valves with one track showed 25 % and 430 HV respectively. With two superimposed tracks the hardness was up to 470 HV in the upper track.

Para abaratar el coste de recuperación o sustitución de válvulas de escape en motores diesel, estas se fabrican con un material base económico, recubriéndose el asiento de la válvula con otro material al que se exigirá elevada dureza y buena resistencia al impacto, a la corrosión y al desgaste erosivo en caliente (>550 °C y sin lubricación. Partiendo de esta idea, en el presente trabajo se han determinado los parámetros adecuados para realizar, mediante la técnica de plaqueado láser, un recubrimiento con Stellite 6, sobre sustratos de acero AISI 304 (probetas planas y SAE EV8 (válvulas reales. Sobre las válvulas, se depositaron uno y dos cordones superpuestos, se minimizó la presencia de poros y grietas, modificando el grado de solape inicial y final de los cordones circulares y la potencia en función del ángulo girado. Así, se

Internal Stress Distribution Measurement of TIG Welded SUS304 Samples Using Neutron Diffraction Technique

Science.gov (United States)

Muslih, M. Refai; Sumirat, I.; Sairun; Purwanta

2008-03-01

The distribution of residual stress of SUS304 samples that were undergone TIG welding process with four different electric currents has been measured. The welding has been done in the middle part of the samples that was previously grooved by milling machine. Before they were welded the samples were annealed at 650 degree Celsius for one hour. The annealing process was done to eliminate residual stress generated by grooving process so that the residual stress within the samples was merely produced from welding process. The calculation of distribution of residual stress was carried out by measuring the strains within crystal planes of Fe(220) SUS304. Strain, Young modulus, and Poisson ratio of Fe(220) SUS304 were measured using DN1-M neutron diffractometer. Young modulus and Poisson ratio of Fe(220) SUS304 sample were measured in-situ. The result of calculations showed that distribution of residual stress of SUS304 in the vicinity of welded area is influenced both by treatments given at the samples-making process and by the electric current used during welding process.

Comportamiento frente a la corrosión de los aceros inoxidables AISI 430L P/M

OpenAIRE

Corpas, F. A.; Iglesias, F. J.; Ruiz, J. M.; Codina, S.; Ruiz, J. M.; García, V.

2004-01-01

In this paper we have studied the resistance to corrosion of the 430L ferritic stainless steels, manufactured by powder metallurgy. We have compared the behaviour of the different series of 430L stainless steels sintered, tempered and annealing, in different corrosive environments. Finally, the microstructure of the steels was determined by means of scanning electron microscopy. The better resistance to corrosion are produced in the steel annealing to 300ºC and 600ºC.

En es...

Environmental effect on cracking of an 304L austenitic stainless steels in PWR primary environment under cyclic loading

International Nuclear Information System (INIS)

Huin, N.

2013-01-01

The present study was undertaken in order to get further insights on cracking mechanisms in a 304L stainless steel. More precisely, a first objective of this study was to evaluate the effect of various cold working conditions on the cyclic stress-strain behavior and the fatigue life in air and in PWR primary environment. In air a prior hardening was found to reduce the fatigue life in the LCF regime but not in primary environment. In both environments, the fatigue limit of the hardened materials was increased after cold working.The second objective addresses the effect of the air and the PWR primary environments on the cracking mechanisms (initiation and propagation) in the annealed material in the LCF regime. More precisely, the kinetics of crack initiation and micro crack propagation were evaluated with a multi scale microscopic approach in air and in primary environment. In PWR primary environment, during the first cycles, preferential oxidation occurs along emerging dissociated dislocation and each cycle generates a new C-rich/Fe-rich oxide layer. Then, during cycling, the microstructure evolves from stacking fault into micro twinning and preferential oxidation occurs by continuous shearing and dissolution of the passive film. Beyond a certain crack depth (≤3 μm), the crack starts to propagate with a direction close to a 90 degrees angle from the surface. The crack continues its propagation by successive generation of shear bands and fatigue striations at each cycle up to failure. The role of corrosion hydrogen on these processes is finally discussed. (author)

Intergranular Corrosion Behavior of 304LN Stainless Steel Heat Treated at 623 K (350 °C)

Science.gov (United States)

Singh, Raghuvir; Kumar, Mukesh; Ghosh, Mainak; Das, Gautam; Singh, P. K.; Chattoraj, I.

2013-01-01

Low temperature sensitization of 304LN stainless steel from the two pipes, differing slightly in chemical composition, has been investigated; specimens were aged at 623 K (350 °C) for 20,000 hours and evaluated for intergranular corrosion and degree of sensitization. The base and heat-affected zone (HAZ) of the 304LN-1 appear resistant to sensitization, while 304LN-2 revealed a "dual" type microstructure at the transverse section and HAZ. The microstructure at 5.0-mm distance from the fusion line indicates qualitatively less sensitization as compared to that at 2.0 mm. The 304LN-2 base alloy shows overall lower degree of sensitization values as compared to the 304LN-1. A similar trend of degree of sensitization was observed in the HAZ where it was higher in the 304LN-1 as compared to the 304LN-2. The weld zone of both the stainless steels suffered from cracking during ASTM A262 practice E, while the parent metals and HAZs did not show such fissures. A mottled image within the ferrite lamella showed spinodal decomposition. The practice E test and transmission electron microscopy results indicate that the interdendritic regions may suffer from failure due to carbide precipitation and due to the evolution of brittle phase from spinodal decomposition.

In situ neutron diffraction study of grain-orientation-dependent phase transformation in 304L stainless steel at a cryogenic temperature

International Nuclear Information System (INIS)

Tao Kaixiang; Wall, James J.; Li, Hongqi; Brown, Donald W.; Vogel, Sven C.; Choo, Hahn

2006-01-01

In situ time-of-flight neutron diffraction was performed to investigate the martensitic phase transformation during quasistatic uniaxial compression testing of 304L stainless steel at 300 and 203 K. In situ neutron diffraction enabled the bulk measurement of intensity evolution for various hkl atomic planes during the austenite (fcc) to martensite (hcp and bcc) phase transformation. Based on the neutron diffraction patterns, the martensite phases were observed from the very beginning of the plastic deformation at 203 K. However, at 300 K, no newly formed martensite, except a small amount of preexisting hcp phase, was observed throughout the test. From the changes in the relative intensities of individual hkl atomic planes, the grain-orientation-dependent phase transformation was investigated. The preferred orientation of the newly formed martensite grains was also investigated for the sample deformed at 203 K using neutron diffraction. The results reveal the orientation relationships between the austenite and the newly formed martensites. The fcc grain family diffracting with (200) plane normal parallel to the loading axis is favored for the fcc to bcc transformation and the bcc (200) plane normals are primarily aligned along the loading direction. For the fcc to hcp transformation, the fcc grains with (111) plane normals at an angle in between about 10 deg. and 50 deg. to the loading direction are favored

5 CFR 352.304 - International organizations covered.

Science.gov (United States)

2010-01-01

... REEMPLOYMENT RIGHTS Detail and Transfer of Federal Employees to International Organizations § 352.304... public international organization or international organization preparatory commission only when the... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false International organizations covered. 352...

Efecto de las sales fundidas en la termofluencia del acero inoxidable tipo 304

Directory of Open Access Journals (Sweden)

González-Rodríguez, G.

1995-06-01

Full Text Available Problems caused by both hot corrosion and creep type-damage occurring on superheater and reheater tubes of power plants using heavy oil as fuel shorten their design lives. The acceleration of hot corrosion attack of boilers is caused by the presence of fuel ash deposits containing mainly vanadium, sodium and sulphur, in the form of Na₂SO₄ y V₂O₅ and V₂O₅ which form low melting point compounds. In addition to this, the tubes are exposed to the action of both high stresses and high temperatures, producing the so called creep damage. In this work, creep rupture tests were carried out in the temperature range of 620 to 660 °C in static air and in corrosive environments. The corrosive environments included 100 % Na₂SO₄, 100 % V₂O₅ and a 80 % V₂O₅ + 20 % Na₂SO₄ mixture.

Los problemas causados tanto por la corrosión por sales fundidas, así como por la termofluencia en los tubos de los sobrecalentadores y recalentadores de una planta de potencia que usa combustibles fósiles, reducen su vida prevista en diseño. La aceleración de la corrosión por sales fundidas es causada por la presencia de cenizas que contienen principalmente vanadio, sodio y azufre en la forma de Na₂SO₄ y V₂O₅, los cuales forman mezclas con eutécticos de bajo punto de fusión. Adicionalmente, los tubos están expuestos a la acción de altos esfuerzos y altas temperaturas, lo cual propicia la termofluencia del material. En este trabajo, se han realizado ensayos de termofluencia hasta la rotura en aire y en ambientes corrosivos en el rango de temperaturas de 620 a 660 °C. Los ambientes corrosivos fueron 100 % Na₂SO₄, 100 % V₂O₅, y una mezcla 20 % Na₂SO₄-80 % V₂O₅.

Assessment of tensile and creep data for types 304 and 316 stainless steel

International Nuclear Information System (INIS)

Sikka, V.K.; Booker, M.K.

1976-01-01

Austenitic stainless steels of types 304 and 316 are prime construction materials for nuclear fast breeder reactors and will be used in the temperature range where elevated-temperature, tensile, creep, and fatigue properties are required to calculate the design stress limits. This report examines the possible variations in such properties, using data from several sources including data from Japan and the United Kingdom. United States data were shown to contain the largest variations in both tensile and creep properties, with Japanese data the least. For a given country no distinction could be made in variations in tensile properties of types 304 and 316 stainless steels, but variations in standard error of estimate for all creep properties analyzed were significantly lower for type 316 stainless steel than corresponding variations in creep properties of type 304 stainless steel. The data from each of these countries showed the same creep rupture strength (at 10 4 h) for type 316 stainless steel; this was not true for the type 304 stainless steel. Results of the analysis performed in this paper showed that the U.S. and foreign data on types 304 and 316 stainless steels could possibly be combined for the determination of design stress intensity limits

Caracterización de una nueva membrana cerámica de microfiltración con soporte de tejido en acero inoxidable flexible

Directory of Open Access Journals (Sweden)

Palacio, L.

1999-04-01

Full Text Available In this work we present the characterization of a ceramic flexible membrane, made by SynthesechemieⓇ, with a nominal pore size of 0.45 μm. This membrane consists in an α-alúmina porous support which has an embedded stainless steel metallic network, onto what a selective layer of titanium dioxide has been deposited. Membrane characterization has been realized with the aid of several techniques as: atomic force microscopy (AFM, air-liquid displacemente porosimetry and mercury porosimetry. Each tecnique giving information on different aspects: surface characteristics, bulk pores and active pores. Although the total pore size distribution is rather broad, the active pores (those opened to flux present a narrow distribution with a mean pore size very close to the manufacturer nominal value.

En este trabajo se ha abordado la caracterización de una membrana cerámica de microfiltración flexible, fabricada por SynthesechemieⓇ con tamaño de poro nominal de 0.45 μm. Ésta consiste en un soporte poroso de α-alúmina que posee un armazón formado por una red metálica de acero inoxidable sobre el cual existe una capa selectiva de óxido de titanio. La caracterización de la membrana ha sido realizada con diversas técnicas como: microscopia de fuerza atómica (AFM, porometría de desplazamiento aire-líquido y porosimetría de mercurio. Cada técnica da información sobre aspectos diferentes: superficie, poros totales y poros activos. Si bien la distribución total de tamaños de poro es bastante ancha, los poros activos (abiertos al flujo presentan una distribución de tamaños estrecha con un valor medio muy próximo al nominal.

Fatigue Crack Growth Characteristics of Cold Stretched STS 304 Welded Joint

Energy Technology Data Exchange (ETDEWEB)

Lee, Jeong Won; Na, Seong Hyeon; Yoon, Dong Hyun; Kim, Jae Hoon [Chungnam Nat’l Univ., Daejeon (Korea, Republic of); Kim, Young Kyun; Kim, Ki Dong [Korea Gas Coporation R& D Division, Daejeon (Korea, Republic of)

2017-09-15

STS 304 steel is used as pressure vessel material, and although it exhibits excellent mechanical characteristics at a low temperature, it is heavier than other materials. To address this issue, a method using cold-stretching techniques for STS 304 can be applied. In this study, a cold-stretching part and welded joint specimen were directly obtained from a cold-stretching pressure vessel manufactured according to ASME code. Fatigue crack propagation tests were carried out at room temperature and -170℃ using the compliance method for stress ratios of 0.1 and 0.5. The results indicate that crack growth rate of the welded joint is higher than that of the cold-stretching part within the same stress intensity factor range. The outcome of this work is expected to serve as a basis for the development of a cold-stretched STS 304 pressure vessel.

Interaction of Liquid Sodium With 304 Stainless Steel

National Research Council Canada - National Science Library

Moberly, John

1968-01-01

The effect of a liquid sodium environment on 304 stainless steel has important engineering significance because of the potential use of this liquid-metal solid-metal system in fast breeder reactors...

Stress Corrosion Cracking of Type 304 Stainless Steel

National Research Council Canada - National Science Library

Louthan, M

1964-01-01

Stress corrosion cracking of type 304 stainless steel exposed in dilute chloride solutions is being investigated at the Savannah River Laboratory in attempts to develop a fundamental understanding of the phenomenon...

10 CFR 435.304 - The COSTSAFR Program.

Science.gov (United States)

2010-01-01

... DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY STANDARDS FOR NEW FEDERAL LOW-RISE RESIDENTIAL BUILDINGS Mandatory Energy Efficiency Standards for Federal Residential Buildings § 435.304 The COSTSAFR... building in a specific geographic location. The most effective set of energy conservation measures is...

Influência da temperatura interpasse nas propriedades do aço inoxidável duplex durante a soldagem pelo processo a arco submerso

Directory of Open Access Journals (Sweden)

Tatiana Resende Alvarez

2014-06-01

Full Text Available Os aços inoxidáveis duplex (AID são materiais que apresentam elevada resistência à corrosão com altos valores de resistência mecânica motivando sua utilização em diversos componentes de processo na indústria offshore. No entanto, existem grandes desafios na soldagem destes materiais em termos de produtividade e qualidade da junta produzida, tendo em vista sua ampla utilização desde componentes de pequenas espessuras, tais como umbilicais, até de grandes espessuras, como tubulações de linhas de injeção de água salgada. No que concerne a tubulações de espessuras pequenas é empregado satisfatoriamente o processo de soldagem Gas Tungsten Arc Welding (GTAW conhecido como TIG. No que diz a respeito a tubulações de paredes espessas foi implementado, recentemente, o processo automático de soldagem por arco submerso (SAW na linha de pré-montagem de tubulações, aumentando consideravelmente a produtividade das juntas produzidas. No entanto, existe uma grande demanda de tempo para a realização de um novo passe de solda, em virtude da máxima temperatura interpasse exigida ser inferior a 150ºC. Portanto, o presente trabalho apresenta os resultados da caracterização e avaliação da resistência à corrosão de uma junta soldada correspondente a uma tubulação de aço inoxidável duplex (AID UNS S31803 de 21,4 mm de espessura de parede soldada pelos processos de soldagem MIG (GMAW na raiz e arco submerso (SAW no enchimento e acabamento, empregando-se temperaturas interpasses entre 150 e 290ºC. Os resultados da caracterização das propriedades mecânicas, composição química e resistência à corrosão em diversas regiões da junta soldada foram comparadas com os obtidos para o metal de base (MB da tubulação, assim como com os valores mínimos exigidos pelas normas de projeto. Deste modo, o presente trabalho permite avaliar a influência da temperatura interpasse nas propriedades da junta em decorrência de um poss

48 CFR 28.304 - Risk-pooling arrangements.

Science.gov (United States)

2010-10-01

... CONTRACTING REQUIREMENTS BONDS AND INSURANCE Insurance 28.304 Risk-pooling arrangements. Agencies may establish risk-pooling arrangements. These arrangements are designed to use the services of the insurance industry for safety engineering and the handling of claims at minimum cost to the Government. The agency...

Comparative Study of Hardening Mechanisms During Aging of a 304 Stainless Steel Containing α'-Martensite

Science.gov (United States)

Jeong, S. W.; Kang, U. G.; Choi, J. Y.; Nam, W. J.

2012-09-01

Strain aging and hardening behaviors of a 304 stainless steel containing deformation-induced martensite were investigated by examining mechanical properties and microstructural evolution for different aging temperature and time. Introduced age hardening mechanisms of a cold rolled 304 stainless steel were the additional formation of α'-martensite, hardening of α'-martensite, and hardening of deformed austenite. The increased amount of α'-martensite at an aging temperature of 450 °C confirmed the additional formation of α'-martensite as a hardening mechanism in a cold rolled 304 stainless steel. Additionally, the increased hardness in both α'-martensite and austenite phases with aging temperature proved that hardening of both α'-martensite and austenite phases would be effective as hardening mechanisms in cold rolled and aged 304 stainless steels. The results suggested that among hardening mechanisms, hardening of an α'-martensite phase, including the diffusion of interstitial solute carbon atoms to dislocations and the precipitation of fine carbide particles would become a major hardening mechanism during aging of cold rolled 304 stainless steels.

7 CFR 900.304 - Who may vote.

Science.gov (United States)

2010-01-01

... Conduct of Referenda To Determine Producer Approval of Milk Marketing Orders To Be Made Effective Pursuant to Agricultural Marketing Agreement Act of 1937, as Amended § 900.304 Who may vote. (a) Each producer... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements...

Formation of abrasion-resistant coatings of the AlSiFe{sub x}Mny intermetallic compound type on the AISI 304L alloy

Energy Technology Data Exchange (ETDEWEB)

Martinez-Peralez, L. G.; Flores-Valdes, A.; Salinas-Rodriguez, A.; Ochoa-Palacios, R. M.; Toscano-giles, J. A.; Torres-Torres, J.

2016-05-01

The α-Al{sub 9}FeMnSi and α-Al{sub 9}FeMn{sub 2}Si intermetallics formed by reactive sintering of Al, Si, Mn, Fe, Cr and Ni powders have been used in AISI 304L steels to enhance microhardness. Processing variables of the reactive sintering treatment were temperature (600, 650, 700, 750 and 800 degree centigrade), pressure (5, 10 y 20 MPa) and holding time (3600, 5400 y 7200 seconds). Experimental results show that temperature is the most important variable affecting the substrate/coating formation, while pressure does not appear to have a significant effect. The results show the optimum conditions of the reactive sintering that favor the substrate/coating formation are 800 degree centigrade, 20 MPa and 7200 seconds. Under these conditions, the reaction zone between the substrate and coating is more compacted and well-adhered, with a microhardness of 1300 Vickers. The results of SEM and X-Ray diffraction confirmed the formation of β-Al{sub 9}FeMnSi and β-Al{sub 9}FeMn{sub 2}Si intermetallics in the substrate/coating interface as well as the presence of Cr and Ni, indicating diffusion of these two elements from the substrate to the interface. (Author)

State Environmental Policy Act (SEPA) environmental checklist forms for 304 Concretion Facility Closure Plan

International Nuclear Information System (INIS)

1993-11-01

The 300 Area of the Hanford Site contains reactor fuel manufacturing facilities and several research and development laboratories. Recyclable scrap uranium with zircaloy-2 and copper silicon alloy, uranium-titanium alloy, beryllium/zircaloy-2 alloy, and zircaloy-2 chips and fines were secured in concrete billets (7.5-gallon containers) in the 304 Facility, located in the 300 Area. The beryllium/zircaloy-2 alloy and zircaloy-2 chips and fines are designated as mixed waste with the characteristic of ignitability. The concretion process reduced the ignitability of the fines and chips for safe storage and shipment. This process has been discontinued and the 304 Facility is now undergoing closure as defined in the Resource Conservation and Recovery Act (RCRA) of 1976 and the Washington Administrative Code (WAC) Dangerous Waste Regulations, WAC 173-303-040. This closure plan presents a description of the 304 Facility, the history of materials and waste managed, and the procedures that will be followed to close the 304 Facility. The 304 Facility is located within the 300-FF-3 (source) and 300-FF-5 (groundwater) operable units, as designated in the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) (Ecology et al. 1992). Contamination in the operable units 300-FF-3 and 300-FF-5 is scheduled to be addressed through the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980 remedial action process. Therefore, all soil remedial action at the 304 Facility will be conducted as part of the CERCLA remedial action of operable units 300-FF-3 and 300-FF-5

Diffusion and autoradiographic investigations of the tritium--304 stainless steel system

International Nuclear Information System (INIS)

Downs, G.L.; Braun, J.D.; Chaney, K.F.; Powell, G.W.

1975-01-01

The diffusion coefficient of tritium in 304-stainless steel at low temperatures (100 to 300 0 C) was determined. Autoradiography was used to establish the concentration as well as the distribution of tritium in the alloy. The autoradiographic study shows that tritium is distributed heterogeneously at room temperature in the cold-worked alloy and also in the fusion zone of weldments. Tritium partitions preferentially to the delta ferrite in weldments and to martensite produced by the cold working of 304-stainless steel. (auth)

24 CFR 941.304 - Full proposal content.

Science.gov (United States)

2010-04-01

... with all applicable Federal relocation requirements; (j) Life-cycle analysis. For new construction and... cooling systems, and which shall include a life-cycle cost analysis of the installation, maintenance and... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Full proposal content. 941.304...

Intergranular stress corrosion in soldered joints of stainless steel 304

International Nuclear Information System (INIS)

Zamora R, L.

1994-01-01

The intergranular stress cracking of welded joints of austenitic stainless steel, AISI 304, is a serious problem in BWR type reactors. It is associated with the simultaneous presence of three factors; stress, a critical media and sensibilization (DOS). EPR technique was used in order to verify the sensibilization degree in the base metal, and the zone affected by heat and welding material. The characterization of material was done. The objective of this work is the study of microstructure and the evaluation of EPR technique used for the determination of DOS in a welded plate of austenitic stainless steel AISI 304. (Author)

41 CFR 304-6.5 - What guidelines must we follow when using the Standard Form (SF) 326?

Science.gov (United States)

2010-07-01

... REQUIREMENTS 6-PAYMENT GUIDELINES Reports § 304-6.5 What guidelines must we follow when using the Standard Form... 41 Public Contracts and Property Management 4 2010-07-01 2010-07-01 false What guidelines must we follow when using the Standard Form (SF) 326? 304-6.5 Section 304-6.5 Public Contracts and Property...

Superficial and electrochemical study of stainless steel 304l with an inhibitory protective coating (TiO2 and ZrO2)

International Nuclear Information System (INIS)

Davila N, M. L.; Contreras R, A.; Arganis J, C. R.

2014-10-01

The degradation mechanisms in the boiling water reactors (BWR) have been an alert focus for owners, especially the cracking by stress corrosion cracking (SCC), therefore different techniques have been studied to inhibit this problem inside which is the water injection of hydrogen feeding (HWC, Hydrogen Water Chemistry), together with the noble metals injection (NMCA, Nobel Metal Chemical Addition) and the ceramic materials injection that form an inhibitory protective coating (Ipc). In this work the Ipc was simulated, for which were carried out hydro-thermals deposits starting from suspensions of 1000 ppm of zirconium oxide in its crystalline phase baddeleyite and titanium oxides in its anatase and rutile phases, on test tubes of stainless steel 304l previously rusty under simulated conditions of pressure and temperature of a BWR (288 C and 8 MPa). The superficial characterization was realized by scanning electron microscopy, energy-dispersive of X-ray and X-ray diffraction. The capacity to mitigate the corrosion was studied with the electrochemical technique of Tafel polarization (288 C and 8 MPa). The steel presents the formation of two oxide coatings formed by magnetite and hematite. The baddeleyite presents a deposit more thick and homogeneous it also presents the most negative electrochemical potential of corrosion, what indicates that it has the bigger capacity to mitigate the SCC. (Author)

Thermal fatigue of a 304L austenitic stainless steel: simulation of the initiation and of the propagation of the short cracks in isothermal and aniso-thermal fatigue

International Nuclear Information System (INIS)

Haddar, N.

2003-04-01

The elbow pipes of thermal plants cooling systems are submitted to thermal variations of short range and of variable frequency. These variations bound to temperature changes of the fluids present a risk of cracks and leakages. In order to solve this problem, EDF has started the 'CRECO RNE 808' plan: 'thermal fatigue of 304L austenitic stainless steels' to study experimentally on a volume part, the initiation and the beginning of the propagation of cracks in thermal fatigue on austenitic stainless steels. The aim of this study is more particularly to compare the behaviour and the damage of the material in mechanic-thermal fatigue (cycling in temperature and cycling in deformation) and in isothermal fatigue (the utmost conditions have been determined by EDF for the metal: Tmax = 165 degrees C and Tmin = 90 degrees C; the frequency of the thermal variations can reach a Hertz). A lot of experimental results are given. A model of lifetime is introduced and validated. (O.M.)

41 CFR 105-72.304 - Program income.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Program income. 105-72... Management § 105-72.304 Program income. (a) Federal awarding agencies shall apply the standards set forth in this section in requiring recipient organizations to account for program income related to projects...

Estudio de corrosión galvánica en pares latón/acero inoxidable y latón/fundición de hierro

Directory of Open Access Journals (Sweden)

Ohanian, M.

2011-08-01

Full Text Available Corrosion attack in heat exchanger systems is a topic of main interest for the maintenance in each industrial plant. These are multigalvanic systems with particular geometric and fluidodynamic complexity. Corrosive damages include zinc selective dealeation in copper alloys. In order to explain zinc dealeation attack, this paper deals with laboratory scale testing, characterization and interactions between two copper and zinc alloys (Yellow brass –UNS C268– and Admiralty brass –UNS C443– compared to AISI 316 stainless steel and cast iron. The tests were performed at 20 °C in 1.5 % NaCl and 1.5 % Na₂SO₄ solutions, pH 8 and each material was characterized by potentiodynamic sweeps. The couples are analyzed by studying transient galvanic currents. We conclude about the cause of the analyzed pathology, brass protection potential ranges and its coupling compatibility with other metals.

El ataque por corrosión en los sistemas intercambiadores de calor constituye un problema para el mantenimiento de cualquier planta industrial. Se trata de sistemas multigalvánicos con particular complejidad geométrica y fluidodinámica. Las patologías corrosivas incluyen el fenómeno de dealeación selectiva de cinc en las aleaciones de cobre. A fin de explicar un caso particular de ataque por decinficación (deterioro en placa de intercambiador de calor de tubos de inoxidable, el presente trabajo aborda en ensayos a escala de laboratorio, la caracterización e interacciones entre dos aleaciones de cobre y cinc, (Yellow brass –UNS C268– y Admiralty brass –UNS C443–, respecto a acero inoxidable AISI 316 y fundición gris de hierro. Los ensayos se realizan a 20 °C en disoluciones de NaCl 1,5 % y Na₂SO₄ 1,5 % y pH 8. Se caracterizan electroquímicamente las aleaciones y materiales involucrados mediante barridos potenciodinámicos. Los pares galvánicos formados se analizan mediante el

48 CFR 932.304-2 - Certificate of eligibility.

Science.gov (United States)

2010-10-01

... CONTRACTING REQUIREMENTS CONTRACT FINANCING Loan Guarantees for Defense Production 932.304-2 Certificate of eligibility. (h) Guaranteed loan applications shall be authorized and transmitted to the Federal Reserve Bank only by the Secretary or designee specified for that purpose. ...

13 CFR 127.304 - How does a concern obtain certification from an approved certifier?

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false How does a concern obtain certification from an approved certifier? 127.304 Section 127.304 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION WOMEN-OWNED SMALL BUSINESS FEDERAL CONTRACT ASSISTANCE PROCEDURES Certification of EDWOSB or WOSB...

Static strain aging type AISI-304 austenitic stainless steel

International Nuclear Information System (INIS)

Trindade, M.B.

1981-03-01

Static strain aging of type AISI-304 austenitic stainless steel was studied from room temperature up to 623K by conducting tests in which the load was held approximately constant, continuously relaxing and unloaded. The aging times varied between 10s and 100h, using a plastic pre deformation of 9% in most of the cases. The static strain aging of 304 steel furnished an activation energy of 23,800 cal/mol. This implies that vacancies play an important role on the aging process. The curve of the variation of the discontinuous yielding with aging time presented different stages, to which specific mathematical expressions were developed. These facts permited the conclusion that Snoek type mechanisms are responsible for the aging in such conditions. (Author) [pt

5 CFR 831.304 - Service with the Cadet Nurse Corps during World War II.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Service with the Cadet Nurse Corps during World War II. 831.304 Section 831.304 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT (CONTINUED... Nurse Corps during World War II. (a) Definitions and special usages. In this section— (1) Basic pay is...

Adesão de linhagem selvagem de Streptococcus thermophilus em superfície de aço inoxidável e efeitos da higienização na sua remoção Adhesion of a wild strain of Streptococcus thermophilus onto stainless steel surfaces and the effects of cleaning and sanification on its removal

Directory of Open Access Journals (Sweden)

Ana Lourdes Neves GÂNDARA

2000-04-01

Full Text Available Linhagem selvagem de Streptococcus thermophilus isolada de leite pasteurizado foi avaliada em modelo experimental quanto a adesão em superfície de aço inoxidável e comportamento frente à limpeza e sanificação. Em leite, a adesão do microrganismo em aço inoxidável foi estudada em 6h de contato a 45°C sob agitação e uma higienização com detergentes alcalino e ácido seguida de sanificação foi utilizada para avaliação do comportamento das células aderidas frente à higienização. Esse microrganismo aderiu a essa superfície produzindo uma carga de 10(4UFC/cm². Após a limpeza alcalina não foram detectadas células aderidas; em seguida a limpeza ácida 6 UFC/cm² ainda foram detectadas. A sanificação com hipoclorito de sódio, após a limpeza, foi suficiente para reduzir a carga de S. thermophilus selvagem aderida ao aço inoxidável. O modelo experimental mostrou-se adequado para o estudo, indicando que a cultura selvagem de Streptococcus thermophilus é produtora de biofilme em superfície de aço inoxidável. A limpeza da superfície de aço inoxidável por detergência alcalina remove mais que 99,9% das células aderidas. Pequenos números de células remanescentes são removidos na detergência ácida o que demonstra a necessidade das diferentes etapas e tipos de detergentes para a eficiência da limpeza. Melhores resultados na remoção desse biofilme são alcançadas com detergência alcalina seguida de detergência ácida e mais eficientemente quando se utiliza uma sanificação complementar com hipoclorito de sódio.A wild strain of Streptococcus thermophilus isolated from pasteurized milk was evaluated using an experimental model with respect to its adhesion onto stainless steel surfaces and its behaviour when submitted to cleansing and sanification. In milk, the adhesion of the microorganism on to stainless steel surfaces was studied after 6 hours of contact at 45°C with agitation, and after a cleansing process

48 CFR 815.304-70 - Evaluation factor commitments.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Evaluation factor... AFFAIRS CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection 815.304-70 Evaluation factor commitments. (a) VA contracting officers shall: (1) Include provisions in negotiated...

Oxidation behaviour at 1123 K of AISI 304-Ni/Al-Al2O3/TiO2 multilayer system deposited by flame spray

Directory of Open Access Journals (Sweden)

Cervera, I.

2011-04-01

Full Text Available The oxidation behaviour of alumina/titania (97/3, 87/13 and 60/40 ceramic coatings using a Ni-Al coupling layer was studied in a thermobalance. Both layers were deposited on an AISI 304 stainless steel base metal by the flame spray technique. The coated steel was heated from room temperature to 1,123 K at 40 K min –1, oxidized in air for 50 h, and then cooled to room temperature at 40 K min–1. The mass gain was mainly attributed to the oxidation of Ni-Al coupling layer. Kinetic laws, DW·S –1 (mg.mm–2 vs. time (hours were close to a parabolic plot for each sample. Surface composition of ceramic top layer and the cross section of multilayer system were analysed using a wide range of experimental techniques including Scanning Electron Microscopy (SEM, equipped with a link energy dispersive X-Ray spectroscopy (EDX and X-Ray diffraction (XRD before and after the oxidation process. Coatings 97/3 and 87/13 presented a stable structure after flame spray deposition and they did not evolve with the oxidation process, while most of the 60/40 coating changed to a metastable structure after deposition and to a more stable structure after oxidation with high micro-cracks content. SEM and EDX microanalysis of the cross-sections showed that significant oxidation and a weak intergranular precipitation had been produced in the coupling layer and on the stainless steel base metal, respectively.El comportamiento a oxidación de recubrimientos cerámicos alúmina/titania (97/3, 87/13, 60/40 usando una capa de anclaje Ni-Al se ha estudiado mediante una termobalanza. Ambas capas se han depositado sobre un acero inoxidable AISI 304 utilizando la técnica de proyección llama (FS. El acero recubierto se ha calentado desde la temperatura ambiente hasta 1.123 K a 40 K min–1, se ha oxidado al aire durante 50 h, y luego se ha enfriado hasta la temperatura ambiente a 40 K min–1. La ganancia en masa se atribuye a la oxidación de la capa de enganche Ni-Al. La cin

46 CFR 308.524 - Application for cancellation of Open Cargo Policy, Form MA-304.

Science.gov (United States)

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Application for cancellation of Open Cargo Policy, Form... § 308.524 Application for cancellation of Open Cargo Policy, Form MA-304. The standard form of application for cancellation of an Open Cargo Policy Form MA-304 may be obtained from the American War Risk...

Effect of heat input on the microstructure, residual stresses and corrosion resistance of 304L austenitic stainless steel weldments

Energy Technology Data Exchange (ETDEWEB)

Unnikrishnan, Rahul, E-mail: rahulunnikrishnannair@gmail.com [Department of Metallurgical and Materials Engineering, Visvesvaraya National Institute of Technology (VNIT), South Ambazari Road, Nagpur 440010, Maharashtra (India); Idury, K.S.N. Satish, E-mail: satishidury@gmail.com [Department of Metallurgical and Materials Engineering, Visvesvaraya National Institute of Technology (VNIT), South Ambazari Road, Nagpur 440010, Maharashtra (India); Ismail, T.P., E-mail: tpisma@gmail.com [Department of Metallurgical and Materials Engineering, Visvesvaraya National Institute of Technology (VNIT), South Ambazari Road, Nagpur 440010, Maharashtra (India); Bhadauria, Alok, E-mail: alokbhadauria1@gmail.com [Department of Metallurgical and Materials Engineering, Visvesvaraya National Institute of Technology (VNIT), South Ambazari Road, Nagpur 440010, Maharashtra (India); Shekhawat, S.K., E-mail: satishshekhawat@gmail.com [Department of Metallurgical Engineering and Materials Science, Indian Institute of Technology Bombay (IITB), Powai, Mumbai 400076, Maharashtra (India); Khatirkar, Rajesh K., E-mail: rajesh.khatirkar@gmail.com [Department of Metallurgical and Materials Engineering, Visvesvaraya National Institute of Technology (VNIT), South Ambazari Road, Nagpur 440010, Maharashtra (India); Sapate, Sanjay G., E-mail: sgsapate@yahoo.com [Department of Metallurgical and Materials Engineering, Visvesvaraya National Institute of Technology (VNIT), South Ambazari Road, Nagpur 440010, Maharashtra (India)

2014-07-01

Austenitic stainless steels are widely used in high performance pressure vessels, nuclear, chemical, process and medical industry due to their very good corrosion resistance and superior mechanical properties. However, austenitic stainless steels are prone to sensitization when subjected to higher temperatures (673 K to 1173 K) during the manufacturing process (e.g. welding) and/or certain applications (e.g. pressure vessels). During sensitization, chromium in the matrix precipitates out as carbides and intermetallic compounds (sigma, chi and Laves phases) decreasing the corrosion resistance and mechanical properties. In the present investigation, 304L austenitic stainless steel was subjected to different heat inputs by shielded metal arc welding process using a standard 308L electrode. The microstructural developments were characterized by using optical microscopy and electron backscattered diffraction, while the residual stresses were measured by X-ray diffraction using the sin{sup 2}ψ method. It was observed that even at the highest heat input, shielded metal arc welding process does not result in significant precipitation of carbides or intermetallic phases. The ferrite content and grain size increased with increase in heat input. The grain size variation in the fusion zone/heat affected zone was not effectively captured by optical microscopy. This study shows that electron backscattered diffraction is necessary to bring out changes in the grain size quantitatively in the fusion zone/heat affected zone as it can consider twin boundaries as a part of grain in the calculation of grain size. The residual stresses were compressive in nature for the lowest heat input, while they were tensile at the highest heat input near the weld bead. The significant feature of the welded region and the base metal was the presence of a very strong texture. The texture in the heat affected zone was almost random. - Highlights: • Effect of heat input on microstructure, residual

Estudio de la influencia microbiológica en la corrosión de latones (UNS C68700, UNS C443 y acero inoxidable AISI 316;

Directory of Open Access Journals (Sweden)

Ohanian, Mauricio

2014-06-01

Full Text Available Microorganisms may play an important role in the corrosion process and generate conditions which affect the rate and/or the mechanism of deterioration. They become visible by the formation of biofilms: clusters of microorganisms and extracellular polymers. These biofilms affect not only the durability of the material, but also reduce the heat transfer. The present work studied the growth of aerobic and anaerobic heterotrophic microorganisms and sulfate reducing bacteria on aluminum brass (UNS C68700, admiralty brass (UNS C443 and stainless steel AISI 316 in exposure experiments held in the Bay of Montevideo (Uruguay. The influence of the biofilm growth on the corrosion behavior was studied by electrochemical techniques: polarization curves and Electrochemical Impedance Spectroscopy (EIS. The selection of the most suitable material for the exposure conditions is discussed and hypotheses of the corrosion mechanism are presented. Although stainless steel AISI 316 presented the lowest corrosion rate it showed localized deterioration.Los microorganismos influyen de manera significativa en el proceso corrosivo y generan condiciones que afectan la velocidad y/o el mecanismo de deterioro. Su presencia se manifiesta por la formación de bio-películas: conglomerados de bacterias y polímeros extracelulares. Dichas bio-películas afectan la durabilidad del material, la velocidad de flujo y la transferencia de calor. En el presente trabajo se evalúa el crecimiento de microorganismos heterótrofos aerobios, heterótrofos anaerobios y bacterias sulfato-reductoras sobre latón aluminio (UNS C68700, latón almirantazgo (UNS C443 y acero inoxidable AISI 316. Asimismo, se estudia la influencia del crecimiento de la bio-película sobre el comportamiento corrosivo mediante técnicas electroquímicas: curvas de polarización y espectroscopia de impedancia electroquímica. Las exposiciones se realizan en la Bahía de Montevideo, estuario del Río de la Plata

25 CFR 304.8 - Use of label by dealer.

Science.gov (United States)

2010-04-01

... GOVERNMENT MARK § 304.8 Use of label by dealer. Any dealer offering for sale silver bearing the Government mark may, if he wishes, attach to silver so marked a label or ticket calling attention to the...

Formación de maclas durante el enfriamiento en aceros inoxidables superferríticos envejecidos

Directory of Open Access Journals (Sweden)

Salán, M. N.

2005-12-01

Full Text Available Superferritic stainless steels show a BCC structure free of austenite at any temperature. Intermediate ageing temperatures, close to 475 °C, induce a-chromium content modulation and only after long periods of time, it is possible to detect chromium rich α' phase, which is responsible for embrittlement (475 °C embrittlement. In this work, ageing thermal treatments at intermediate temperatures in the superferritic stainless steel DIN 1.4575, have allowed to relate the associated hardness increase with time and temperature by means of a relationship that is compatible with a thermally activated process. After quenching from ageing temperature, twinning formation has been observed, and the extent of twinning is proportional to the increase in hardness, showing in this way that twinning density is proportional to embrittlement level.

Los aceros inoxidables superferríticos se caracterizan por su estructura cúbica centrada, libre de austenita a cualquier temperatura. Sometidos a temperaturas intermedias, próximas a 475 °C, revelan una modulación del contenido en Cr de la red. Después de tiempos prolongados se forma fase α', fragilizante y rica en cromo, fenómeno conocido como fragilización a 475 °C. En este trabajo, los tratamientos de envejecimiento realizados a temperaturas intermedias para un superferrítico DIN 1.4575 han permitido relacionar el incremento de dureza asociado a éstos con el tiempo de tratamiento, mediante una expresión coherente con un proceso térmicamente activado. Por otra parte, se ha detectado la presencia de maclas en el acero envejecido y templado en agua, siendo proporcional su densidad al grado de endurecimiento provocado por el tratamiento.

Evaluation of liquid metal embrittlement of stainless steel 304 by cadmium and cadmium-aluminum solutions

International Nuclear Information System (INIS)

Iyer, N.C.; Peacock, H.B.; Thomas, J.K.; Begley, J.A.

1994-01-01

The susceptibility of stainless steel 304 (SS304) to liquid metal embrittlement (LME) by cadmium (Cd) and cadmium-aluminum (Cd-Al) solutions was examined as part of a failure evaluation for SS304-clad cadmium reactor safety rods which had been exposed to elevated temperatures. The safety rod test data and destructive examination of the specimens indicated that LME was not the failure mode. The available literature data also suggest that austenitic stainless steels are not particularly susceptible to LME by Cd or Cd-Al solutions. However, the literature data is not conclusive and an experimental study was therefore conducted to examine the susceptibility of SS304 to LME by Cd and Cd-Al solutions. Temperatures from 325 to 600 C and strain rates from 1x10 -6 to 5x10 -5 s -1 were of interest in this evaluation. Tensile tests carried out in molten Cd-Al and Cd solutions over these temperatures and strain rates with both smooth bar and notched specimens showed no evidence of LME. U-bend tests conducted in liquid Cd at 500 and 600 C also showed no evidence of LME. It is concluded that SS304 is not subject to LME by Cd or Cd-Al solutions over the range of temperatures and strain rates of interest. ((orig.))

SCC-induced failure of a 304 stainless steel pipe

International Nuclear Information System (INIS)

Tapping, R.L.; Disney, D.J.; Szostak, F.J.

1993-01-01

On 1991 January 12, a 304 Stainless Steel (SS) suction line in the AECL-Research NRU reactor failed, shutting down the reactor for approximately 12 months. The pipe, a 32 mm schedule 40 304 stainless steel line exposed to D 2 O at temperatures ≤35 degrees C had been in service for approximately 20 years, although no manufacturing data or composition specifications were available. The failure and resultant leak resulted in a small loss of D 2 O moderator from the reactor vessel. The pipe cracked approximately 180 degrees C around the circumference of a weld. This failure was unexpected and hense a thorough metallographic examination was carried out on the failed section, on the rest of the line (Line 1212), and on representative samples from the rest of the reactor in order to assess the integrity of the remaining piping

[Effects of non-saccharomyces albicans metabolic products on the proliferation of human umbilical vein endothelial cell ECV304].

Science.gov (United States)

Chen, Bin; Che, Tuanjie; Bai, Decheng; He, Xiangyi

2013-04-01

To evaluate the effects of non-Saccharomyces albicans metabolic products on the cell cycle distribution and proliferation of human umbilical vein endothelial cell ECV304 cells in vitro. The parallel dilution supernatant of Saccharomyces tropicalis, Saccharomyces krusei and Saccharomyces glabrata were prepared, and 1, 4, 16-fold(s) diluted concentration and control group were set up. The line of human umbilical vein endothelial cell ECV304 was cultured in vitro and treated by non-Saccharomyces albicans supernatant. The proliferous effect of ECV304 induced by non-Saccharomyces albicans supernatant after 24, 48, 72 h was detected by the methods of MTT, and the changes of cell density and cycle after 48 h were investigated by inverted microscope and flow cytometry. At the 24th hour, all of the higher concentration (1-fold) of non-Saccharomyces albicans supernatant and the 4-folds diluted Saccharomyces krusei could promote ECV304 proliferation(P Saccharomyces albicans supernatant at 48h and 72th hour, Saccharomyces krusei supernatant and Saccharomyces glabrata supernatant significantly increased proliferation rate of ECV304, while Saccharomyces tropicalis supernatant group showed no significant change no matter which concentration was tested. At 48th hour after adding the non-Saccharomyces albicans supernatant, the ECV304 cells density treated by Saccharomyces krusei supernatant and Saccharomyces glabrata supernatant were significantly higher under the inverted microscope. The G0/G1 population of ECV304 cells decreased while cell proliferation index (PI) increased after incubated with Saccharomyces krusei supernatant and Saccharomyces glabrata supernatant for 48 hours (P Saccharomyces tropicalis group showed no significant change (P > 0.05). The metabolic products of Sacharoymces krusei and Saccharomyces glabrata could induce proliferation of ECV304 cell, which suggests non-Saccharomyces albicans should be undergone more attention clinically in detection and treatment.

State Environmental Policy Act (SEPA) environmental checklist forms for 304 Concretion Facility Closure Plan. Revision 2

Energy Technology Data Exchange (ETDEWEB)

1993-11-01

The 300 Area of the Hanford Site contains reactor fuel manufacturing facilities and several research and development laboratories. Recyclable scrap uranium with zircaloy-2 and copper silicon alloy, uranium-titanium alloy, beryllium/zircaloy-2 alloy, and zircaloy-2 chips and fines were secured in concrete billets (7.5-gallon containers) in the 304 Facility, located in the 300 Area. The beryllium/zircaloy-2 alloy and zircaloy-2 chips and fines are designated as mixed waste with the characteristic of ignitability. The concretion process reduced the ignitability of the fines and chips for safe storage and shipment. This process has been discontinued and the 304 Facility is now undergoing closure as defined in the Resource Conservation and Recovery Act (RCRA) of 1976 and the Washington Administrative Code (WAC) Dangerous Waste Regulations, WAC 173-303-040. This closure plan presents a description of the 304 Facility, the history of materials and waste managed, and the procedures that will be followed to close the 304 Facility. The 304 Facility is located within the 300-FF-3 (source) and 300-FF-5 (groundwater) operable units, as designated in the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) (Ecology et al. 1992). Contamination in the operable units 300-FF-3 and 300-FF-5 is scheduled to be addressed through the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980 remedial action process. Therefore, all soil remedial action at the 304 Facility will be conducted as part of the CERCLA remedial action of operable units 300-FF-3 and 300-FF-5.

48 CFR 815.304 - Evaluation factors and significant subfactors.

Science.gov (United States)

2010-10-01

... AFFAIRS CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection 815.304 Evaluation factors and significant subfactors. (a) In an effort to assist SDVOSBs and VOSBs, contracting officers shall include evaluation factors providing additional consideration to such offerors in...

Microstructural characterization in dissimilar friction stir welding between 304 stainless steel and st37 steel

International Nuclear Information System (INIS)

Jafarzadegan, M.; Feng, A.H.; Abdollah-zadeh, A.; Saeid, T.; Shen, J.; Assadi, H.

2012-01-01

In the present study, 3 mm-thick plates of 304 stainless steel and st37 steel were welded together by friction stir welding at a welding speed of 50 mm/min and tool rotational speed of 400 and 800 rpm. X-ray diffraction test was carried out to study the phases which might be formed in the welds. Metallographic examinations, and tensile and microhardness tests were used to analyze the microstructure and mechanical properties of the joint. Four different zones were found in the weld area except the base metals. In the stir zone of the 304 stainless steel, a refined grain structure with some features of dynamic recrystallization was evidenced. A thermomechanically-affected zone was characterized on the 304 steel side with features of dynamic recovery. In the other side of the stir zone, the hot deformation of the st37 steel in the austenite region produced small austenite grains and these grains transformed to fine ferrite and pearlite and some products of displacive transformations such as Widmanstatten ferrite and martensite by cooling the material after friction stir welding. The heat-affected zone in the st37 steel side showed partially and fully refined microstructures like fusion welding processes. The recrystallization in the 304 steel and the transformations in the st37 steel enhanced the hardness of the weld area and therefore, improved the tensile properties of the joint. - Highlights: ► FSW produced sound welds between st37 low carbon steel and 304 stainless steel. ► The SZ of the st37 steel contained some products of allotropic transformation. ► The material in the SZ of the 304 steel showed features of dynamic recrystallization. ► The finer microstructure in the SZ increased the hardness and tensile strength.

Comparative study of high temperature oxidation behaviour in AISI 304 and AISI 439 stainless steels

Directory of Open Access Journals (Sweden)

Antônio Claret Soares Sabioni

2003-06-01

Full Text Available This work deals with a comparison of high temperature oxidation behaviour in AISI 304 austenitic and AISI 439 ferritic stainless steels. The oxidation experiments were performed between 850 and 950 °C, in oxygen and Ar (100 vpm H2. In most cases, it was formed a Cr2O3 protective scale, whose growth kinetics follows a parabolic law. The exception was for the the AISI 304 steel, at 950 °C, in oxygen atmosphere, which forms an iron oxide external layer. The oxidation resistance of the AISI 439 does not depend on the atmosphere. The AISI 304 has the same oxidation resistance in both atmospheres, at 850 °C, but at higher temperatures, its oxidation rate strongly increases in oxygen atmosphere. Concerning the performance of these steels under oxidation, our results show that the AISI 439 steel has higher oxidation resistance in oxidizing atmosphere, above 850 °C, while, in low pO2 atmosphere, the AISI 304 steel has higher oxidation resistance than the AISI 439, in all the temperature range investigated.

The Corrosion Behavior of Cold-Rolled 304 Stainless Steel In Salt Spray Environments

International Nuclear Information System (INIS)

Chiang, M.F.; Young, M.C.; Huang, J.Y.

2011-01-01

Saline corrosion is one of the major degradation mechanisms for stainless steel type 304 (SS304) dry storage cask during the spent fuel interim storage period. Slow strain rate test (SSRT) and neutral salt spray test (NSS) were performed at 85 degrees Celsius and 200 degrees Celsius with 0.5 wt% sodium chloride mist sprayed on the cold-rolled SS304 specimens of different degrees of reduction in this study. The weight changes of the NSS specimens tested at 85 degrees Celsius for 2000 hours differed greatly from those at 200 degrees Celsius. The weight loss of NSS specimens was not significant at 85 degrees Celsius but the weight gain decreased gradually with increasing the cold-rolled reduction. The yield strength (YS) and ultimate tensile stress (UTS) values obtained from the SSRT tests for lightly cold-rolled specimens in the salt spray environment at 85 degrees Celsius and 200 degrees Celsius are slightly lower than in air. But for those with 20% reductions, the specimen strengths were no longer changed by the saline corrosion. The preliminary results demonstrated that the quality and performance of cold-rolled SS304 is acceptable for fabrication of dry storage casks. However, more work on the corrosion behavior of cold-rolled stainless steel in the saline atmosphere is needed to better understand its long-term performance.

EFSA CEF Panel (EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids), 2014. Scientific Opinion on Flavouring Group Evaluation 304, Revision 1 (FGE.304Rev1): Four carboxamides from Chemical Groups 30

DEFF Research Database (Denmark)

Beltoft, Vibe Meister; Binderup, Mona-Lise; Frandsen, Henrik Lauritz

The Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids of the European Food Safety Authority was requested to evaluate four flavouring substances in the Flavouring Group Evaluation 304, Revision 1 (FGE.304Rev1) using the Procedure in Commission Regulation (EC) No 1565...... criteria and identity for the materials of commerce have been provided for all four candidate substances....

Studies on Stress Corrosion Cracking of Super 304H Austenitic Stainless Steel

Science.gov (United States)

Prabha, B.; Sundaramoorthy, P.; Suresh, S.; Manimozhi, S.; Ravishankar, B.

2009-12-01

Stress corrosion cracking (SCC) is a common mode of failure encountered in boiler components especially in austenitic stainless steel tubes at high temperature and in chloride-rich water environment. Recently, a new type of austenitic stainless steels called Super304H stainless steel, containing 3% copper is being adopted for super critical boiler applications. The SCC behavior of this Super 304H stainless steel has not been widely reported in the literature. Many researchers have studied the SCC behavior of steels as per various standards. Among them, the ASTM standard G36 has been widely used for evaluation of SCC behavior of stainless steels. In this present work, the SCC behavior of austenitic Fe-Cr-Mn-Cu-N stainless steel, subjected to chloride environments at varying strain conditions as per ASTM standard G36 has been studied. The environments employed boiling solution of 45 wt.% of MgCl2 at 155 °C, for various strain conditions. The study reveals that the crack width increases with increase in strain level in Super 304H stainless steels.

Weldability of AISI 304 to copper by friction welding

Energy Technology Data Exchange (ETDEWEB)

Kirik, Ihsan [Batman Univ. (Turkey); Balalan, Zulkuf [Firat Univ., Elazig (Turkey)

2013-06-01

Friction welding is a solid-state welding method, which can join different materials smoothly and is excessively used in manufacturing industry. Friction welding method is commonly used in welding applications of especially cylindrical components, pipes and materials with different properties, for which other welding methods remain incapable. AISI 304 stainless steel and a copper alloy of 99.6 % purity were used in this study. This couple was welded in the friction welding machine. After the welding process, samples were analyzed macroscopically and microscopically, and their microhardness was measured. Tensile test was used to determine the bond strength of materials that were joined using the friction welding method. At the end of the study, it was observed that AISI 304 stainless steel and copper could be welded smoothly using the friction welding method and the bond strength is close to the tensile strength of copper. (orig.)

Elevated temperature tensile properties of borated 304 stainless steel

International Nuclear Information System (INIS)

Stephens, J.J.; Sorenson, K.B.; McConnell, P.

1993-01-01

This paper presents a comparison of the tensile properties of Powder Metallurgy (PM) 'Grade A' material with that of the conventional IM 'Grade B' material for two selected Types (i.e., boron contents) as defined by the ASTM A887 specification: Types 304B5 and 304B7. Tensile properties have been generated for these materials at temperatures ranging from room temperature to 400degC (752degF). The data at higher temperatures are required for ASME Code Case purposes, since the use temperature of a basket under 'worst case' cask conditions may be as high as 343degC (650degF), due to self-heating by the activated fuel elements. We will also discuss the current status of efforts aimed at obtaining an ASME Boiler and Pressure Vessel Code Case for selected grades of borated stainless steel covered by the ASTM A887 specification. (J.P.N.)

Electrochemical polarization behavior of sensitized SUS 304 stainless steel in high temperature water

Energy Technology Data Exchange (ETDEWEB)

Kushiya, K [Tohoku Univ., Sendai (Japan); Sugimoto, K; Ejima, T

1978-11-01

Anodic polarization curves for a solution-treated or sensitized SUS 304 stainless steel and solution-treated Fe-Ni-Cr ternary alloys containing 10%Ni and 6 to 14%Cr have been measured in deaerated 0.5 mol/l Na/sub 2/SO/sub 4/ solutions of pH 2.0 to 5.9 at 298, 523 and 553 K. Corrosion potentials for U-bend SCC test specimens of sensitized SUS 304 stainless steel have also been monitored for a long time in the same solutions as those used for the polarization measurements except that they were aerated. It was found that the differences in the current densities in the passive state, i sub(pass), between the solution treated steel and the sensitized one and also between the ternary alloy with higher Cr content and the one with lower Cr content become large with increasing temperature and decreasing pH. This means that the difference in the values of i sub(pass) between grain bodies and Cr-depleted zones along grain boundaries of sensitized steel becomes larger and susceptibility to intergranular corrosion of the sensitized steel in the passivation region becomes higher with increasing temperature and decreasing pH. Since corrosion potentials for the U-bend SCC test specimens in air-satulated solutions lie in the passive region of anodic polarization curves for the sensitized steel in deaerated solutions, the intergranular stress-corrosion cracking of the sensitized steel in high temperature water with dissolved oxygen is considered to be caused by the preferential corrosion in the Cr-depleted zone.

Study on the Effect of Laser Welding Parameters on the Microstructure and Mechanical Properties of Ultrafine Grained 304L Stainless Steel

Directory of Open Access Journals (Sweden)

Reihane Nafar Dehsorkhi

2016-12-01

Full Text Available In the present study, an ultrafine grained (UFG 304L stainless steel with the average grain size of 300 nm was produced by a combination of cold rolling and annealing. Weldability of the UFG sample was studied by Nd: YAG laser welding under different welding conditions. Taguchi experimental design was used to optimize the effect of frequency, welding time, laser current and laser pulse duration on the resultant microstructure and mechanical properties. X-ray Diffraction (XRD, Optical Microscope (OM, Scanning Electron Microscope (SEM, Transmission Electron Microscope (TEM, microhardness measurements and tension tests were conducted to characterize the sample after thermomechanical processing and laser welding. The results showed that the ultrafine grained steel had the yield strength of 1000 Mpa and the total elongation of 48%, which were almost three times higher than those of the as-received sample. The microstructure of the weld zone was shown to be a mixture of austenite and delta ferrite. The microhardness of the optimized welded sample (315 HV0.5 was found to be close to the UFG base metal (350 HV. It was also observed that the hardness of the heat affected zone (HAZ was  lower than that of the weld zone, which was related to the HAZ grain growth during laser welding. The results of optimization also showed that the welding time was the most important parameter affecting the weld strength. Overall, the study showed that laser welding could be an appropriate and alternative welding technique for the joining of UFG steels.

31 CFR 30.4 - Q-4: What actions are necessary for a TARP recipient to comply with the standards established...

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Q-4: What actions are necessary for a... or manipulation of earnings)? 30.4 Section 30.4 Money and Finance: Treasury Office of the Secretary of the Treasury TARP STANDARDS FOR COMPENSATION AND CORPORATE GOVERNANCE § 30.4 Q-4: What actions are...

A novel c. 204 Ile68Met germline variant in exon 2 of the mutL homolog 1 gene in a colorectal cancer patient

Czech Academy of Sciences Publication Activity Database

Vodička, Pavel; Caja, F.; Vymetálková, Veronika; Procházka, Pavel; Vodičková, Ludmila; Schwarzová, L.; Slyšková, Jana; Kumar, R.; Schneiderová, M.

2015-01-01

Roč. 9, č. 1 (2015), s. 183-186 ISSN 1792-1074 R&D Projects: GA ČR GPP304/11/P715; GA ČR(CZ) GAP304/12/1585 Institutional support: RVO:68378041 Keywords : mutL homolog 1 * germline mutation * colorectal cancer Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 1.482, year: 2015

Far UV observations of PKS2155-304

International Nuclear Information System (INIS)

Maraschi, L.; Tanzi, E.G.; Treves, A.; Tarenghi, M.

1980-01-01

Several spectra of the BL Lac object PKS2155 - 304 are reported in the 1,150 - 3,200 A band taken with the IUE when the object was in a bright phase. The UV flux connects smoothly with the optical and IR observations of the source in its brightest state and its extrapolation matches the soft X-ray flux, implying a change in spectral slope around 10 15 Hz. (UK)

Evaluation of liquid metal embrittlement of SS304 by Cd and Cd-Al solutions

International Nuclear Information System (INIS)

Thomas, J.K.; Iyer, N.C.; Begley, J.A.

1992-01-01

The susceptibility of stainless steel 304 to liquid metal embrittlement (LME) by cadmium (Cd) and cadmium-aluminum (Cd-Al) solutions was examined as part of a failure evaluation for SS304-clad cadmium reactor safety rods which had been exposed to elevated temperatures. The active, or cadmium (Cd) bearing, portion of the safety rod consists of a 0.756 in. diameter aluminum allow (Al-6061) core, a 0.05 in. thick Cd layer, and a 0.042 in. thick Type 304 stainless steel cladding. The safety rod thermal tests were conducted as part of a program to define the response of reactor core components to a hypothetical LOCA for the Savannah River Site (SRS) production reactor. LME was considered as a potential failure mechanism based on the nature of the failure and susceptibility of austenitic stainless steels to embrittlement by other liquid metals

Exploring EUV Spicules Using 304 Ang He II Data from SDO/AIA

Science.gov (United States)

Snyder, Ian; Sterling, Alphonse C.; Falconer, David A.; Moore, Ronald L.

2015-01-01

'' Hinode Ca II spicules, even though we observed these 304 Angstrom spicules at a polar location, where typically only "Type II'' spicules are seen in the Hinode Ca II images. A.C.S. and R.L.M. were supported by funding from the Heliophysics Division of NASA's Science Mission Directorate through the Living With a Star Targeted Research and Technology Program, and the Hinode Project. I.S. was supported by NSF's Research Experience for Undergraduates Program

Friction and bending forces evaluation of AISI 304 DDQ steel sheet forming by bending tests under deep-drawing multiaxial stresses; Evaluacion de la fuerza de doblado y de friccion en el conformado de chapa de acero inoxidable AISI 304 DDQ mediante ensayos de doblado en condiciones multiaxiales de embuticion

Energy Technology Data Exchange (ETDEWEB)

Coello, J.; Miguel, V.; Ferrer, C.; Calatayud, A.; Martinez, A.

2012-11-01

Die radius is a critical area from the viewpoint of friction in forming processes. Moreover the sheet, that has been previously deformed in flange area, suffers bending and unbending stresses. Then, die-sheet contact in die radius must be especially considered in order to guarantee the suitable lubrication conditions. In the present work, a test method is carried out for evaluating an AISI 304 DDQ steel under similar conditions to those existing in the die radius area and that, usually, are not really reproduced in traditional bending under tensions tests. Deformation under pure shear condition, the bending and the radius angle have been established as variables of the tests. Results allow to obtain the apparent pressure sheet-bending tool, that increases with bending angle and decreases with tool radius. This last variable is the most significant while the bending angle has lesser influence. Although experimental results present some concordances with values obtained by analytical methods, some corrections must be considered in them in order to improve the theoretical values. (Author) 18 refs.

Corrosion behavior of niobium coated 304 stainless steel in acid solution

Energy Technology Data Exchange (ETDEWEB)

Pan, T.J., E-mail: tjpan@cczu.edu.cn [School of Material Science and Engineering, Jiangsu Collaborative Innovation Center for Photovolatic Science and Engineering, Changzhou University, Changzhou 213164 (China); Jiangsu Key Laboratory of Material Surface Technology, Changzhou 213164 (China); Chen, Y.; Zhang, B. [School of Material Science and Engineering, Jiangsu Collaborative Innovation Center for Photovolatic Science and Engineering, Changzhou University, Changzhou 213164 (China); Hu, J. [School of Material Science and Engineering, Jiangsu Collaborative Innovation Center for Photovolatic Science and Engineering, Changzhou University, Changzhou 213164 (China); Jiangsu Key Laboratory of Material Surface Technology, Changzhou 213164 (China); Li, C. [Light Industry College of Liaoning University, Shenyang 110036 (China)

2016-04-30

Highlights: • The Nb coating produced by HEMAA offers good protection for 304SS in acid solution. • The coating increases corrosion potential and induces decrease of corrosion rate. • The protection of coating is ascribed to the stability of Nb in acid solution. - Abstract: The niobium coating is fabricated on the surface of AISI Type 304 stainless steel (304SS) by using a high energy micro arc alloying technique in order to improvecorrosion resistance of the steel against acidic environments. The electrochemical corrosion resistance of the niobium coating in 0.7 M sulfuric acid solutions is evaluated by electrochemical impedance spectroscopy, potentiodynamic polarization and the open circuit potential versus time. Electrochemical measurements indicate that the niobium coating increases the free corrosion potential of the substrate by 110 mV and a reduction in the corrosion rate by two orders of magnitude compared to the substrate alone. The niobium coating maintains large impedance and effectively offers good protection for the substrate during the long-term exposure tests, which is mainly ascribed to the niobium coating acting inhibiting permeation of corrosive species. Finally, the corresponding electrochemical impedance models are proposed to elucidate the corrosion resistance behavior of the niobium coating in acid solutions.

Corrosion behavior of niobium coated 304 stainless steel in acid solution

International Nuclear Information System (INIS)

Pan, T.J.; Chen, Y.; Zhang, B.; Hu, J.; Li, C.

2016-01-01

Highlights: • The Nb coating produced by HEMAA offers good protection for 304SS in acid solution. • The coating increases corrosion potential and induces decrease of corrosion rate. • The protection of coating is ascribed to the stability of Nb in acid solution. - Abstract: The niobium coating is fabricated on the surface of AISI Type 304 stainless steel (304SS) by using a high energy micro arc alloying technique in order to improvecorrosion resistance of the steel against acidic environments. The electrochemical corrosion resistance of the niobium coating in 0.7 M sulfuric acid solutions is evaluated by electrochemical impedance spectroscopy, potentiodynamic polarization and the open circuit potential versus time. Electrochemical measurements indicate that the niobium coating increases the free corrosion potential of the substrate by 110 mV and a reduction in the corrosion rate by two orders of magnitude compared to the substrate alone. The niobium coating maintains large impedance and effectively offers good protection for the substrate during the long-term exposure tests, which is mainly ascribed to the niobium coating acting inhibiting permeation of corrosive species. Finally, the corresponding electrochemical impedance models are proposed to elucidate the corrosion resistance behavior of the niobium coating in acid solutions.

12 CFR 347.304 - Accounting for fees on international loans.

Science.gov (United States)

2010-01-01

... accepted accounting principles. ... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Accounting for fees on international loans. 347... OF GENERAL POLICY INTERNATIONAL BANKING International Lending § 347.304 Accounting for fees on...

Ductile fracture of circumferentially cracked type-304 stainless steel pipes in tension

Energy Technology Data Exchange (ETDEWEB)

Zahoor, A.; Norris, D.M.

1984-11-01

Circumferentially cracked pipes subjected to tensile load were analyzed for finite length and constant depth part-through cracks located at the inside of the pipe wall. The analysis postulated loads sufficient to cause net-section yielding of the flawed section. It was demonstrated that a propensity for predominantly radial growth exists for part-through cracks loaded in tension. This result is similar to the result for bend loading, except that bend loading causes more favorable conditions for wall breakthrough than tension loading. Numerical results were developed for 4-in. and 24-in-dia pipes. Safety margins for displacement controlled loads were described by a safety assessment diagram. This diagram defines a curve delineating leak from fracture in a space of nondimensional crack length and crack depth. 4-india schedule 80 Type-304 stainless steel pipes with length to radius ratio (L/R) of up to 100 exhibited leak-before-break behavior.

Ductile fracture of circumferentially cracked type-304 stainless steel pipes in tension

International Nuclear Information System (INIS)

Zahoor, A.; Norris, D.M.

1984-01-01

Circumferentially cracked pipes subjected to tensile load were analyzed for finite length and constant depth part-through cracks located at the inside of the pipe wall. The analysis postulated loads sufficient to cause net-section yielding of the flawed section. It was demonstrated that a propensity for predominantly radial growth exists for part-through cracks loaded in tension. This result is similar to the result for bend loading, except that bend loading causes more favorable conditions for wall breakthrough than tension loading. Numerical results were developed for 4-in. and 24-in-dia pipes. Safety margins for displacement controlled loads were described by a safety assessment diagram. This diagram defines a curve delineating leak from fracture in a space of nondimensional crack length and crack depth. 4-india schedule 80 Type-304 stainless steel pipes with length to radius ratio (L/R) of up to 100 exhibited leak-before-break behavior

Action of an aerobic hydrogenotroph bacteria isolated from ultrapure water systems on AISI 304 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Gales, Gregoire [DTN/SMTM/LMTE, CEA Cadarache, F-13108 Saint-Paul-lez-Durance (France)]|[DSV/DEVM/LEMIR, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France); Roy, Marc; Feron, Damien [DEN/DPC/SCCME/LECA, Bat 458, CEA Saclay F- 91191 Gif sur Yvette (France); Libert, Marie-Francoise; Sellier, Regine [DTN/SMTM/LMTE, CEA Cadarache, F-13108 Saint-Paul-lez-Durance (France); Cournac, Laurent [DSV/DEVM/LEP, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France); Heulin, Thierry [DSV/DEVM/LEMIR, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France)

2004-07-01

Several microbial studies have been recently performed in nuclear power stations. These studies concerned essentially the formation of bio-films on submerged metal coupons. Heterotrophic micro-organisms have been found in bulk water of nuclear fuel storage basins but the in situ nutrient sources for bacterial development in such highly oligo-trophic water was unknown. In nuclear environments, radiations lead to the production of molecular hydrogen, hydrogen peroxide and some radicals (OH, O{sub 2}{sup -}) by radiolysis of water or embedding matrices. Bacterial oxidation of molecular H{sub 2} commonly occurs in nature, as molecular hydrogen represents a high-energy reductant. We investigated the microbiology of a ultra-pure water basin containing irradiating waste. The initial aim of this study was to determine if autotrophic bacterial growth was possible in this basin. A major bacteria was isolated (Ralstonia sp. GGLH002) which was able to grow autotrophically with hydrogen as the electron donor and oxygen as the electron acceptor, and heterotrophically with organic nutrients. Its hydrogenase activity has been characterized. We focused then our study on the effects of this strain on 304L AISI stainless steel depending on the nutrient source used for bacterial development, e.g hydrogen or organics. In conclusion, the mechanism of passivation enhanced by Ralstonia sp. GGLH002 on AISI 304L SS still remains unknown. Several techniques could give substantial information, including XPS and polarization curves. It seems for the moment that the major bacteria inhabiting an oxic environment containing hydrogen due to radiolysis is not aggressive to stainless steel in conditions near from its environment. Further investigations are needed to test this hypothesis, including a study of the molecular diversity of the bacteria using culture-independent techniques, as cultivatable bacterial populations represent in general only a fraction of the total bacteria. (authors)

Action of an aerobic hydrogenotroph bacteria isolated from ultrapure water systems on AISI 304 stainless steel

International Nuclear Information System (INIS)

Gales, Gregoire; Roy, Marc; Feron, Damien; Libert, Marie-Francoise; Sellier, Regine; Cournac, Laurent; Heulin, Thierry

2004-01-01

Several microbial studies have been recently performed in nuclear power stations. These studies concerned essentially the formation of bio-films on submerged metal coupons. Heterotrophic micro-organisms have been found in bulk water of nuclear fuel storage basins but the in situ nutrient sources for bacterial development in such highly oligo-trophic water was unknown. In nuclear environments, radiations lead to the production of molecular hydrogen, hydrogen peroxide and some radicals (OH, O 2 - ) by radiolysis of water or embedding matrices. Bacterial oxidation of molecular H 2 commonly occurs in nature, as molecular hydrogen represents a high-energy reductant. We investigated the microbiology of a ultra-pure water basin containing irradiating waste. The initial aim of this study was to determine if autotrophic bacterial growth was possible in this basin. A major bacteria was isolated (Ralstonia sp. GGLH002) which was able to grow autotrophically with hydrogen as the electron donor and oxygen as the electron acceptor, and heterotrophically with organic nutrients. Its hydrogenase activity has been characterized. We focused then our study on the effects of this strain on 304L AISI stainless steel depending on the nutrient source used for bacterial development, e.g hydrogen or organics. In conclusion, the mechanism of passivation enhanced by Ralstonia sp. GGLH002 on AISI 304L SS still remains unknown. Several techniques could give substantial information, including XPS and polarization curves. It seems for the moment that the major bacteria inhabiting an oxic environment containing hydrogen due to radiolysis is not aggressive to stainless steel in conditions near from its environment. Further investigations are needed to test this hypothesis, including a study of the molecular diversity of the bacteria using culture-independent techniques, as cultivatable bacterial populations represent in general only a fraction of the total bacteria. (authors)

CATALIZADOR ESTRUCTURADO DE Pt/Al2O3 SOBRE UNA ESPUMA DE ACERO INOXIDABLE (AISI 314 PARA LA OXIDACIÓN DE CO

Directory of Open Access Journals (Sweden)

Juan P. Bortolozzi

2011-01-01

Full Text Available Se obtuvo un catalizador estructurado por recubrimiento de Pt/Al2O3 sobre las paredes de una espuma de acero inoxidable AISI 314. Para estabilizar térmicamente e incrementar la rugosidad de la superficie de la espuma original se realizó un tratamiento a 900°C por 2 h. El soporte, Al2O3, y el metal activo, Pt, se incorporaron por inmersión. Las técnicas de caracterización aplicadas, XRD, LRS y SEM-EDX, permiten concluir que el tratamiento térmico previo indujo la formación de óxido de cromo y de las espinelas Mn1+xCr2-xO4-x y FeCr2O4 como fases principales en las paredes del sustrato. El espesor de la capa formada es cercano a 1 μm y los cristales producidos tienen forma octaédrica. El cubrimiento de alúmina presentó en general una apariencia homogénea, sin interacción con los óxidos formados durante el tratamiento. El Pt se distribuyó de manera uniforme, resultando un catalizador muy activo para la reacción test elegida: oxidación de monóxido de carbono.

Effect of oxyanions on the IGSCC inhibition of sensitized 304 stainless steel in high temperature water

International Nuclear Information System (INIS)

Tsuge, Hiroyuki; Murayama, Junichiro; Nagano, Hiroo.

1983-01-01

Effect of oxyanions such as MoO 4 2- , WO 4 2- , and CrO 4 2- on the intergranular stress corrosion cracking (IGSCC) of Type 304 stainless steel in high temperature water was studied. The results obtained are as follows: 1) Addition of such oxyanion as MoO 4 2- , WO 4 2- , and CrO 4 2- suppresses IGSCC of sensitized Type 304 stainless steel in high temperature nondeaerated water. The effectiveness of the inhibitive action by the oxyanion is ranked in the order of MoO 4 2- >WO 4 2- >CrO 4 2- . 2) The mechanism of IGSCC inhibition by MoO 4 2- ion for sentized Type 304 stainless steel in high temperature water is considered as follows, i.e., the presence MoO 4 2- ion decreases the dissolution rate of Cr depleted zone at grain boundaries to the level of matrix by helping the formation of the Cr rich film containing MoO 3 or adsorbed MoO 4 2- ion on the surface of Type 304 stainless steel. (author)

Meeting Overlapping Requirements of the Quality Management System and Act 304 at SINAGAMMA, ALURTRON and RAYMINTEX: An Improvement

International Nuclear Information System (INIS)

Nik Arlina Nik Ali; Nurul Huda Mudri; Rohaizah Ahmad

2011-01-01

Sinagama, Alurtron and Raymintex are three facilities at Nuclear Malaysia using high radiation sources to provide irradiation service to customers. These three facilities have to fulfill both the requirements of the MS ISO 9001:2008 standard and the legal requirements of Act 304. To fulfill the requirements of the applicable Act 304, scheduled radiation monitoring on personnel, work place and environment should be carried out. This paper will discuss the effectiveness of the management in fulfilling the requirements of ISO 9001 standard and Act 304 regarding the safety of workers and the environment. (author)

On the ability of some cyclic plasticity models to predict the evolution of stored energy in a type 304L stainless steel submitted to high cycle fatigue

International Nuclear Information System (INIS)

Vincent, L.

2008-01-01

Fatigue analyses of materials are generally based on a so-called stabilized cycle, on which plastic strain amplitude, plastic energy, maximum shear stress and so on are determined. The part of plastic energy which is dissipated in heat cannot be used to accumulate damage and it should be worthwhile extracting only the part of plastic energy which is stored in material microstructure in order to build a consistent damage model. In this paper, some cyclic plasticity models including a polycrystalline model are reformulated in the thermodynamic framework in order to test their capacity to predict both the stress-strain behaviour and the partition of plastic energy for a high cycle fatigue test on a type 304L stainless steel. For an equivalent description of stress-strain loops, the number of kinematic hardening variables chosen in a model may qualitatively alter the prediction of plastic energy partition due to the modification of the isotropic hardening variable. Measurements of the specimen temperature increase due to plastic dissipation is therefore proposed as a convenient complementary experimental data to identify the constitutive equation of the isotropic hardening variable of a cyclic plasticity model. (author)

41 CFR 51-9.304-5 - Reproduction fee schedule.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Reproduction fee schedule... RULES 9.3-Individual Access to Records § 51-9.304-5 Reproduction fee schedule. (a) The fee for... physical characteristics do not permit reproduction by routine electrostatic copying shall be the direct...

Evaluación de la fuerza de doblado y de fricción en el conformado de chapa de acero inoxidable AISI 304 DDQ mediante ensayos de doblado en condiciones multiaxiales de embutición

Directory of Open Access Journals (Sweden)

Coello, J.

2012-08-01

Full Text Available Die radius is a critical area from the viewpoint of friction in forming processes. Moreover the sheet, that has been previously deformed in flange area, suffers bending and unbending stresses. Then, die-sheet contact in die radius must be especially considered in order to guarantee the suitable lubrication conditions. In the present work, a test method is carried out for evaluating an AISI 304 DDQ steel under similar conditions to those existing in the die radius area and that, usually, are not really reproduced in traditional bending under tensions tests. Deformation under pure shear condition, the bending and the radius angle have been established as variables of the tests. Results allow to obtain the apparent pressure sheet-bending tool, that increases with bending angle and decreases with tool radius. This last variable is the most significant while the bending angle has lesser influence. Although experimental results present some concordances with values obtained by analytical methods, some corrections must be considered in them in order to improve the theoretical values.

El radio de entrada a la matriz se considera una de las zonas críticas en los procesos de conformado de chapa mediante embutición profunda. El análisis de la fuerza de fricción y de doblado existentes resulta importante para predecir el comportamiento de la chapa en dicha zona, así como para garantizar una lubricación adecuada a las condiciones de procesado. En el presente trabajo, se aplica un método de ensayo que evalúa las acciones en el proceso de doblado del acero AISI 304 DDQ bajo condiciones similares a las que sufre el material en los procesos de embutición y que no son reproducidas por los clásicos ensayos de doblado bajo tensión. Se establecen como variables la deformación experimentada previamente por el material en condiciones típicas de cortante puro, “pure shear”, el ángulo de doblado y el radio de doblado. Los resultados obtenidos

The effect of precipitated carbides on the pitting corrosion of 304 stainless steel

International Nuclear Information System (INIS)

Kwak, Jai-Hyun; Kim, Kwan-Hun

1985-01-01

In order to investigate the relation between the pitting corrosion and precipitated carbides, the heat treatment of specimens was carried out in two ways: Solution treatment and carbides precipitation treatment. The experiment was focused on the polarization curves of specimens immersed in HCL solution and on the microscopic analysis of the corroded specimens through a potentiodynamic method. It was found out that the intergranular and pitting corrosion occurred remarkably in 0.1N and 1N KCL solution when carbides were precipitated around the grain boundary of the 304 stain steel. The intergranular corrosion was noticed in the region of passivation and the pitting was prominent in the region of passivation break-down. The distribution of pits on the solution treated 304 stainless steel was random, while that of pits on carbides precipitated specimen was concentrated around the grain boundary in 0.1N and 1N HCL solution. It was ascertained that the pitting resistance of the solution treated 304 stainless steel was better than that of carbides precipitated specimen. (Author)

Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

Science.gov (United States)

Hartwig, A.; Decker, M.; Klein, O.; Karl, H.

2015-12-01

The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO2 implanted AISI 304 - examined for different implantation and annealing parameters - is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 1016 cm-2 (Ti+) and 1 × 1017 cm-2 (O+) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 1015 cm-2 (Ti+) and 1 × 1016 cm-2 (O+). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO2 inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

Effect of Microstructure on the Wear Behavior of Heat Treated SS-304 Stainless Steel

OpenAIRE

S. Kumar

2016-01-01

Sliding wear characteristics of some heat treated SS-304 stainless steel against EN-8 steel in dry condition have been studied in the present experimental work. Samples of SS-304 stainless steel have been heated in a muffle furnace in desired temperature and allowed to dwell for two hours. The heated specimen are then cooled in different media namely inside the furnace, open air, cutting grade oil (grade 44) and water at room temperature to obtain different grades of heat treatment. Microstr...

Alergia al látex en los trabajadores sanitarios (I: Vigilancia de la salud

Directory of Open Access Journals (Sweden)

María Soledad Gil Micharet

2007-09-01

Full Text Available La alergia al látex constituye un importante problema de salud entre los trabajadores sanitarios, tanto por su elevada prevalencia como por la gravedad de las reacciones que puede producir. La detección temprana de los síntomas mediante una vigilancia de la salud específica, y las medidas encaminadas a evitar la sensibilización y a prevenir la aparición de sintomatología y la progresión de la enfermedad en los trabajadores ya sensibilizados, son las mejores estrategias de intervención sobre este problema ocupacional. El artículo, realiza en esta primera parte, una revisión de la epidemiología, clínica y diagnóstico, y propone un protocolo médico específico.Látex allergy constitutes an important problem of health in the healthcare workers, so much for its high prevalence as for the graveness of the reactions that can take place. The early detection of the symptoms by means of specific health surveillance, and the measures guided to avoid the sensitization and to prevent the symptomatology appearance and progression of the illness in the sensitized workers, are the best intervention strategies on this occupational problem. The article carries out in this first part, a revision of the epidemiology, clinic and diagnosis, and it proposes a specific medical protocol.

An Investigation into Stress Corrosion Cracking of Dissimilar Metal Welds with 304L Stainless Steel and Alloy 82 in High Temperature Pure Water

Science.gov (United States)

Yeh, Tsung-Kuang; Huang, Guan-Ru; Tsai, Chuen-Horng; Wang, Mei-Ya

For a better understanding toward stress corrosion cracking (SCC) in dissimilar metal welds with 304L stainless steel and Alloy 82, the SCC growth behavior in the transition regions of weld joints was investigated via slow strain rate tensile (SSRT) tests in 280 oC pure water with a dissolve oxygen level of 300 ppb. Prior to the SSRT tests, samples with dissimilar metal welds were prepared and underwent various pretreatments, including post-weld heat treatment (PWHT), shot peening, solution annealing, and mechanical grinding. In addition to the SSRT tests, measurements of degree of sensitization and micro-hardness on the transition regions of the metal welds were also conducted. According to the test results, the samples having undergone PWHTs exhibited relatively high degrees of sensitization. Distinct decreases in hardness were observed in the heat-affected zones of the base metals in all samples. Furthermore, the fracture planes of all samples after the SSRT tests were located at the stainless steel sides and were in parallel with the fusion lines. Among the treating conditions investigated in this study, a PWHT would pose a detrimental effect on the samples in the aspects of mechanical property and degree of SCC. Solution annealing would lead to the greatest improvement in ductility and SCC retardation, and shot peening would provide the treated samples with a positive improvement in ductility and corrosion retardation, but not to a great extent.

Magnetic Susceptibility as a Tool for Investigating Igneous Rocks—Experience from IODP Expedition 304

Directory of Open Access Journals (Sweden)

Roger C. Searle

2008-07-01

Full Text Available Continuous measurements of magnetic susceptibility have been commonly used on Ocean Drilling Program (ODP and Integrated Ocean Drilling Program (IODPexpeditions to study minor lithological variations (forexample, those related to climatic cycles in sedimentary rocks, but they have been less frequently used on igneous rocks, although important post-cruise studies have utilized them (e.g., Ildefonse and Pezard, 2001. Here I report its use (and that of the closely related electrical conductivity on IODP Expedition 304 to examine igneous crustal rocks. Expedition 304/305 targeted the Atlantis Massif, an oceanic core complex on the Mid-Atlantic Ridge, and recovered a suite of igneous rocks comprising mainly gabbros, troctolites, and some diabases (Blackman et al., 2006; Ildefonse et al., 2006, 2007; IODP Expeditions 304 and 305 Scientists, 2005. Shipboard measurements (on D/V JOIDES Resolution of physical properties were made to characterize lithological units and alteration products, to correlate cored material with down-hole logging data, and to interpret broader-scale geophysical data.

High Temperature Fuel Cladding Chemical Interactions Between TRIGA Fuels and 304 Stainless Steel

Energy Technology Data Exchange (ETDEWEB)

Perez, Emmanuel [Idaho National Lab. (INL), Idaho Falls, ID (United States); Keiser, Jr., Dennis D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Forsmann, Bryan [Boise State Univ., ID (United States); Janney, Dawn E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Henley, Jody [Idaho National Lab. (INL), Idaho Falls, ID (United States); Woolstenhulme, Eric C. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-02-01

High-temperature fuel-cladding chemical interactions (FCCI) between TRIGA (Training, Research, Isotopes, General Atomics) fuel elements and the 304 stainless steel (304SS) are of interest to develop an understanding of the fuel behavior during transient reactor scenarios. TRIGA fuels are composed of uranium (U) particles dispersed in a zirconium-hydride (Zr-H) matrix. In reactor, the fuel is encased in 304-stainless-steel (304SS) or Incoloy 800 clad tubes. At high temperatures, the fuel can readily interact with the cladding, resulting in FCCI. A number of FCCI can take place in this system. Interactions can be expected between the cladding and the Zr-H matrix, and/or between the cladding and the U-particles. Other interactions may be expected between the Zr-H matrix and the U-particles. Furthermore, the fuel contains erbium-oxide (Er-O) additions. Interactions can also be expected between the Er-O, the cladding, the Zr-H and the U-particles. The overall result is that very complex interactions may take place as a result of fuel and cladding exposures to high temperatures. This report discusses the characterization of the baseline fuel microstructure in the as-received state (prior to exposure to high temperature), characterization of the fuel after annealing at 950C for 24 hours and the results from diffusion couple experiments carries out at 1000C for 5 and 24 hours. Characterization was carried out via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) with sample preparation via focused ion beam in situ-liftout-technique.

High Temperature Fuel Cladding Chemical Interactions Between TRIGA Fuels and 304 Stainless Steel

International Nuclear Information System (INIS)

Perez, Emmanuel; Keiser Jr, Dennis D.; Forsmann, Bryan; Janney, Dawn E.; Henley, Jody; Woolstenhulme, Eric C.

2016-01-01

High-temperature fuel-cladding chemical interactions (FCCI) between TRIGA (Training, Research, Isotopes, General Atomics) fuel elements and the 304 stainless steel (304SS) are of interest to develop an understanding of the fuel behavior during transient reactor scenarios. TRIGA fuels are composed of uranium (U) particles dispersed in a zirconium-hydride (Zr-H) matrix. In reactor, the fuel is encased in 304-stainless-steel (304SS) or Incoloy 800 clad tubes. At high temperatures, the fuel can readily interact with the cladding, resulting in FCCI. A number of FCCI can take place in this system. Interactions can be expected between the cladding and the Zr-H matrix, and/or between the cladding and the U-particles. Other interactions may be expected between the Zr-H matrix and the U-particles. Furthermore, the fuel contains erbium-oxide (Er-O) additions. Interactions can also be expected between the Er-O, the cladding, the Zr-H and the U-particles. The overall result is that very complex interactions may take place as a result of fuel and cladding exposures to high temperatures. This report discusses the characterization of the baseline fuel microstructure in the as-received state (prior to exposure to high temperature), characterization of the fuel after annealing at 950C for 24 hours and the results from diffusion couple experiments carries out at 1000C for 5 and 24 hours. Characterization was carried out via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) with sample preparation via focused ion beam in situ-liftout-technique.

Efecto de los ciclos térmicos sobre la ZAT de una soldadura multipasos de un acero inoxidable superdúplex SAF 2507 Effect of thermal cycles on the HAZ of a stainless steel multipass weld of superduplex SAF 2507

Directory of Open Access Journals (Sweden)

D. Villalobos

2010-09-01

Full Text Available Los ciclos térmicos de una soldadura multipasos que experimenta un acero inoxidable superdúplex SAF 2507, pueden promover la precipitación de fases secundarias reduciendo significativamente las propiedades mecánicas y la resistencia a la corrosión. Debido a su aplicación en la industria petroquímica, el estudio de las aleaciones superdúplex es de suma importancia para predecir su comportamiento en servicio cuando están involucrados procesos de soldadura por arco eléctrico. En este trabajo, se estudia el cambio microestructural de la zona afectada térmicamente correspondiente al primer cordón depositado de una unión multipasos de acero inoxidable superdúplex SAF 2507 mediante el proceso GTAW y bajo tres temperaturas de interpasos. Los resultados muestran que la temperatura de interpasos tiene una influencia sobre la precipitación de fase sigma en la zona afectada térmicamente del primer cordón depositado.Thermal cycles experienced by a superduplex stainless steel SAF 2507 when is welded, can promote the precipitation of secondary phases which decrease the mechanical properties as well as the corrosion resistance. Due to the application of the duplex alloys in the petrochemical industry, the study of these alloys has become very important in order to predict its service behavior. The aim of this work is to study the microstructural changes in the superduplex stainless steel weld joint after applying the GTAW process under three interpass temperatures after the deposition of every single pass. The results showed that slow cooling rates promoted by the deposition of the subsecuent passes and the higher interpass temperature, promote the precipitation of sigma phase in the HAZ while rapid cooling rates promoted by the lower interpass temperature do not promote the sigma phase precipitation.

Evaluation of structural behaviour and corrosion resistant of austenitic AISI 304 and duplex AISI 2304 stainless steel reinforcements embedded in ordinary Portland cement mortars; Evaluacion del comportamiento estructural y de resistencia a la corrosion de armaduras de acero inoxidable austenitico AISI 304 y duplex AISI 2304 embebidas en morteros de cemento Portland

Energy Technology Data Exchange (ETDEWEB)

Medina, E.; Cobo, A.; Bastidas, D. M.

2012-07-01

The mechanical and structural behaviour of two stainless steels reinforcements, with grades austenitic EN 1.4301 (AISI 304) and duplex EN 1.4362 (AISI 2304) have been studied, and compared with the conventional carbon steel B500SD rebar. The study was conducted at three levels: at rebar level, at section level and at structural element level. The different mechanical properties of stainless steel directly influence the behaviour at section level and structural element level. The study of the corrosion behaviour of the two stainless steels has been performed by electrochemical measurements, monitoring the corrosion potential and the lineal polarization resistance (LPR), of reinforcements embedded in ordinary Portland cement (OPC) mortar specimens contaminated with different amount of chloride over one year time exposure. Both stainless steels specimens embedded in OPC mortar remain in the passive state for all the chloride concentration range studied after one year exposure. (Author) 26 refs.

Material test data of SUS304 welded joints

Energy Technology Data Exchange (ETDEWEB)

Asayama, Tai [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center; Kawakami, Tomohiro [Nuclear Energy System Incorporation, Tokyo (Japan)

1999-10-01

This report summarizes the material test data of SUS304 welded joints. Numbers of the data are as follows: Tensile tests 71 (Post-irradiation: 39, Others: 32), Creep tests 77 (Post-irradiation: 20, Others: 57), Fatigue tests 50 (Post-irradiation: 0), Creep-fatigue tests 14 (Post-irradiation: 0). This report consists of the printouts from 'the structural material data processing system'. (author)

Metallographic observations of AISI 304 - copper dissimular joints

International Nuclear Information System (INIS)

Medeiros, R.C. de; Carvalho Perdigao, S. de

1982-01-01

The current work informs on the SMAW dissimilar joints embrittled by molten Copper. Bead on plate of that metal were deposited on four different base metals to evaluate the phenomena. Conventional and non conventional welding methods were employed to obtain dissimilar joints of AISI 304-Cu. The latter were observed metallographically. These results are to be complemented by mechanical testing actually being performed. (Author) [pt

41 CFR 304-6.9 - Does acceptance by OGE of the Standard Form (SF) 326 constitute a determination by OGE that the...

Science.gov (United States)

2010-07-01

... or a concurrence by OGE in the agency's conflict of interest analysis? 304-6.9 Section 304-6.9 Public...-FEDERAL SOURCE AGENCY REQUIREMENTS 6-PAYMENT GUIDELINES Valuation § 304-6.9 Does acceptance by OGE of the... concurrence by OGE in the agency's conflict of interest analysis? No. OGE is responsible for making the...

Comments on the paper: 'Optical reflectance, optical refractive index and optical conductivity measurements of nonlinear optics for L-aspartic acid nickel chloride single crystal'

Science.gov (United States)

Srinivasan, Bikshandarkoil R.; Naik, Suvidha G.; Dhavskar, Kiran T.

2016-02-01

We argue that the 'L-aspartic acid nickel chloride' crystal reported by the authors of the title paper (Optics Communications, 291 (2013) 304-308) is actually the well-known diaqua(L-aspartato)nickel(II) hydrate crystal.

Oxidation of 304 stainless steel in high-temperature steam

Science.gov (United States)

Ishida, Toshihisa; Harayama, Yasuo; Yaguchi, Sinnosuke

1986-08-01

An experiment on oxidation of 304 stainless steel was performed in steam between 900°C and 1350°C, using the spare cladding of the reactor of the nuclear-powered ship Mutsu. The temperature range was appropriate for a postulated loss of coolant accident (LOCA) analysis of a LWR. The oxidation kinetics were found to obey the parabolic law during the first period of 8 min. After the first period, the parabolic reaction rate constant decreased in the case of heating temperatures between 1100°C and 1250°C. At 1250°C, especially, a marked decrease was observed in the oxide scale-forming kinetics when the surface treated initially by mechanical polishing and given a residual stress. This enhanced oxidation resistance was attributed to the presence of a chromium-enriched layer which was detected by use of an X-ray microanalyzer. The oxidation kinetics equation obtained for the first 8 min is applicable to the model calculation of a hypothetical LOCA in a LWR, employing 304 stainless steel cladding.

Bayesian Model on Fatigue Crack Growth Rate of Type 304 Stainless Steel

Energy Technology Data Exchange (ETDEWEB)

Choi, Sanhae; Yoon, Jae Young; Hwang, Il Soon [Nuclear Materials Laboratory, Seoul National University, Seoul (Korea, Republic of)

2015-10-15

The fatigue crack growth rate curve is typically estimated by deterministic methods in accordance with the ASME Boiler and Pressure Vessel Code Sec. XI. The reliability of nuclear materials must also consider the environmental effect. This can be overcome by probabilistic methods that estimate the degradation of materials. In this study, fatigue tests were carried out on Type 304 stainless steel (STS 304) to obtain a fatigue crack growth rate curve and Paris' law constants. Tests were conducted on a constant load and a constant delta K, respectively. The unknown constants of Paris' law were updated probabilistically by Bayesian inference and the method can be used for the probabilistic structural integrity assessment of other nuclear materials. In this paper, Paris' law constants including C and m for Type 304 stainless steel were determined by probabilistic approach with Bayesian Inference. The Bayesian update process is limited in accuracy, because this method should assume initial data distribution. If we select an appropriate distribution, this updating method is powerful enough to get data results considering the environment and materials. Until now, remaining lives of NPPs are estimated by deterministic methods using a priori model to finally assess structural integrity. Bayesian approach can utilize in-service inspection data derived from aged properties.

Bayesian Model on Fatigue Crack Growth Rate of Type 304 Stainless Steel

International Nuclear Information System (INIS)

Choi, Sanhae; Yoon, Jae Young; Hwang, Il Soon

2015-01-01

The fatigue crack growth rate curve is typically estimated by deterministic methods in accordance with the ASME Boiler and Pressure Vessel Code Sec. XI. The reliability of nuclear materials must also consider the environmental effect. This can be overcome by probabilistic methods that estimate the degradation of materials. In this study, fatigue tests were carried out on Type 304 stainless steel (STS 304) to obtain a fatigue crack growth rate curve and Paris' law constants. Tests were conducted on a constant load and a constant delta K, respectively. The unknown constants of Paris' law were updated probabilistically by Bayesian inference and the method can be used for the probabilistic structural integrity assessment of other nuclear materials. In this paper, Paris' law constants including C and m for Type 304 stainless steel were determined by probabilistic approach with Bayesian Inference. The Bayesian update process is limited in accuracy, because this method should assume initial data distribution. If we select an appropriate distribution, this updating method is powerful enough to get data results considering the environment and materials. Until now, remaining lives of NPPs are estimated by deterministic methods using a priori model to finally assess structural integrity. Bayesian approach can utilize in-service inspection data derived from aged properties

PROTECCIÓN CONTRA LA CORROSIÓN EN SALES FUNDIDAS DE UN ACERO HOT ROLLED, EN EL RANGO DE TEMPERATURAS DE 400 ºC-600 ºC, RECUBIERTO POR ROCIADO TÉRMICO CON ACERO INOXIDABLE 312

Directory of Open Access Journals (Sweden)

JOSE LUDDEY MARULANDA

2009-01-01

Full Text Available Se evaluó la corrosión por sales fundidas mediante la técnica gravimétrica en un acero de bajo carbono tipo hot rolled, rociado térmicamente con una aleación de acero inoxidable tipo 312, con el equipo Rototec, en una mezcla de sal 20% Na2SO4 - 80% V2O5, entre 400ºC - 600ºC, durante tiempos de 1-7-22 horas. Los resultados mostraron una moderada protección de la capa rociada térmicamente y se presentó alta degradación en el recubrimiento a 600ºC. Se concluyó que la velocidad de corrosión aumenta con la temperatura y disminuye con el tiempo de exposición.

28 CFR 44.304 - Special Counsel acting on own initiative.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Special Counsel acting on own initiative...-RELATED EMPLOYMENT PRACTICES Enforcement Procedures § 44.304 Special Counsel acting on own initiative. (a) The Special Counsel may, on his or her own initiative, conduct investigations respecting unfair...

Efecto de la biopelícula en la corrosión de aceros inoxidables

Directory of Open Access Journals (Sweden)

Bethencourt, M.

2010-02-01

Full Text Available In this work, the influence of the biofilms in the corrosion process of different alloys of stainless steel was studied in two sampling points in a wastewater treatment plant during 4 years. The physicochemical microenvironment within the biofilms was characterized through O₂, H₂S and pH microelectrodes. Corrosion rates were quantified from the number, diameter and depth of pits. The results show a remarkable development of the biofilm and a significantly greater number of pits in the grit removal channel than in the sludge recirculation channel. Based on the characteristics of the water phase and microelectrode measurements, our results suggest that biofilms induced corrosion throughout 3 mechanisms: creation of differential aeration cells, areas with different pH and areas having high sulphide production which may react with metal ions.

En este trabajo se ha estudiado la influencia de las biopelículas en los procesos de corrosión de diferentes aleaciones de acero inoxidable, situadas durante 4 años en dos puntos de una estación depuradora de aguas residuales. Se caracterizó el microambiente físico-químico en el interior de las biopelículas mediante microelectrodos de O₂, H_2S y pH, y se cuantificaron las tasas de corrosión a partir del número, diámetro y profundidad de picadura. Los resultados obtenidos muestran un desarrollo más notable de las biopelículas y un número de picaduras significativamente mayor en el canal de salida de desbastes que en el canal de recirculación de fangos. Con base en las características del agua sobrenadante y en las medidas realizadas con microelectrodos, se sugiere que la biopelícula induce la corrosión a través de tres posibles mecanismos: creación de celdas de aireación diferencial, zonas con diferente pH y zonas con elevada producción de sulfuro capaz de reaccionar con iones metálicos.

Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

International Nuclear Information System (INIS)

Hartwig, A.; Decker, M.; Klein, O.; Karl, H.

2015-01-01

The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO 2 implanted AISI 304 – examined for different implantation and annealing parameters – is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 10 16 cm −2 (Ti + ) and 1 × 10 17 cm −2 (O + ) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 10 15 cm −2 (Ti + ) and 1 × 10 16 cm −2 (O + ). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO 2 inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

Sintering, microstructure and properties of WC-AISI304 powder composites

International Nuclear Information System (INIS)

Marques, B.J.; Fernandes, C.M.; Senos, A.M.R.

2013-01-01

Highlights: ► Total replacement of Co binder by stainless steel AISI 304 in WC based composites. ► Processing conditions for WC–stainless steel composites. ► Mechanical behavior and oxidation resistance of WC–stainless steel composites. -- Abstract: Tungsten carbide–stainless steel (AISI 304) based composites were successfully prepared by powder metallurgy routes using vacuum sintering at a maximum temperature of 1500 °C. The effects of the binder amount (between 6 and 15 wt.%) on the phase composition, microstructure and mechanical properties, namely hardness and fracture toughness, were investigated. Appreciable amount of (M,W) 6 C up to 12 wt.% was detected, especially for the higher SS contents. However, a good compromise between toughness and hardness was observed. Besides that, improved oxidation resistance was noticed in WC–SS based composites compared with WC–Co composites. The results are discussed having in mind the correlation between chemical composition, phase composition, microstructure and mechanical behavior

Elevated temperature ductility of types 304 and 316 stainless steel

International Nuclear Information System (INIS)

Sikka, V.K.

1978-01-01

Austenitic stainless steel types 304 and 316 are known for their high ductility and toughness. However, the present study shows that certain combinations of strain rate and test temperature can result in a significant loss in elevated-temperature ductility. Such a phenomenon is referred to as ductility minimum. The strain rate, below which ductility loss is initiated, decreases with decrease in test temperature. Besides strain rate and temperature, the ductility minimum was also affected by nitrogen content and thermal aging conditions. Thermal aging at 649 0 C was observed to eliminate the ductility minimum at 649 0 C in both types 304 and 316 stainless steel. Such an aging treatment resulted in a higher ductility than the unaged value. Aging at 593 0 C still resulted in some loss in ductility. Current results suggest that ductility-minimum conditions for stainless steel should be considered in design, thermal aging data analysis, and while studying the effects of chemical composition

Surface modifications induced by hydrogen in AISI 304 stainless steel

International Nuclear Information System (INIS)

Evangelista, G.E.; Miranda, P.E.V. de

1983-01-01

Hydrogen induced surface modifications of type AISI 304 SS were studied by charging the samples in a 1N a 1N H 2 SO 4 electrolyte at room temperature. Current densities were varied from 500 to 4000 A/m 2 and charging times from 2 to 50 hours. Charged specimens were analysed using optical and electron scanning microscopy. Vickers microhardness tests with small load was also performed. Metallographic etching metodologies were developed (in black and white and colored photographies) which permited identification of all phases present. It was shown that delayed cracks appear somewhat curved on austenite and perfectly strainght on martensite, following the intersections of a phase platlets. These are the regions where α' martensite is located. The habit plane of these cracks might belong to (100) sub(γ) or (221) sub(γ) plane families. A new phenomenon termed hydrogen induced softening was observed on type AISI 304 SS at elevated current densities and/or charging times. (Author) [pt

Adsorption of Pu(IV) Polymer onto 304L Stainless Steel

International Nuclear Information System (INIS)

Bronikowski, M.G.

1999-01-01

'The report, Technical Basis for Safe Operations with Pu-239 Polymer in NMS and S Operating Facilities (F and H Areas), (WSRC-TR-99-00008) was issued in an effort to upgrade the Authorization Basis (AB) for H Area facilities relative to nuclear criticality. At the time, insufficient data were found in the literature to quantify the adsorption of Pu polymer onto the surfaces of stainless steel tanks. Additional experimental or literature information on the adsorption of Pu(IV) polymer and its removal was deemed necessary to support the H Area AB. The results obtained are also applicable to processing in F Area facilities.Additional literature sources suggest that adsorption on the tank walls should not be a safety concern. The sources show that the amount of Pu polymer that adsorbs from a solution comes to a limiting amount in 5 to 7 days after which no additional Pu is adsorbed. Adsorption increases with Pu concentration and decreases with acid concentration. The adsorbed amounts are small varying from 0.5 mg/cm2 for a 0.5 g/l Pu / 0.5M HNO3 solution to 11 mg/cm2 for a 1-3 g/l Pu / 0.1M HNO3 solution. Additionally, acid concentrations greater than 0.1M will remove a percentage of adsorbed Pu.The experimental results have generally confirmed much of what has been reported in the literature. Specifically, adsorption onto stainless steel was found to increase with increased Pu concentration, and decreased acid concentration. The amount adsorbed was found to come to a limiting amount after 5 to 7 days. Pu adsorbed as polymer was found to be harder to remove than if it was adsorbed as Pu(IV). The amount of Pu adsorbed as polymer was found to be almost an order of magnitude more than that from a similar concentration Pu(IV) solution. Unlike the literature, only a slight increase in adsorption values was found when the steel surface was removed, dried, and replaced in the Pu solution. The amount of Pu as polymer which would adsorb onto the surface of a 14,000L tank was

Temperature dependency of external stress corrosion crack propagation of 304 stainless steel

International Nuclear Information System (INIS)

Hayashibara, Hitoshi; Mizutani, Yoshihiro; Mayuzumi, Masami; Tani, Jun-ichi

2010-01-01

Temperature dependency of external stress corrosion cracking (ESCC) of 304 stainless steel was examined with CT specimens. Maximum ESCC propagation rates appeared in the early phase of ESCC propagation. ESCC propagation rates generally became smaller as testing time advance. Temperature dependency of maximum ESCC propagation rate was analyzed with Arrhenius plot, and apparent activation energy was similar to that of SCC in chloride solutions. Temperature dependency of macroscopic ESCC incubation time was different from that of ESCC propagation rate. Anodic current density of 304 stainless steel was also examined by anodic polarization measurement. Temperature dependency of critical current density of active state in artificial sea water solution of pH=1.3 was similar to that of ESCC propagation rate. (author)

Experimental Investigation of Ultrasonic Vibration Assisted Turning of 304 Austenitic Stainless Steel

Directory of Open Access Journals (Sweden)

Ping Zou

2015-01-01

vibration method is employed to scheme out a machining system of ultrasonic vibration assisted turning (MS-UAT. The experiments for turning the workpiece of ASS 304 are conducted with and without ultrasonic vibration using the designed MS-UAT, and then the 3D morphology evaluation parameters Sa and Sq are applied to characterize and analyse the machined surface. The experimental results obtained demonstrate that the process parameters in UAT of ASS 304 have obvious effect on the 3D surface topography and surface roughness of machined workpiece, and the appropriate choice of various process parameters, including ultrasonic amplitude, feed rate, depth of cut, and cutting speed, can enhance the machined surface quality efficiently to make the machining effect of UAT much better than that of CT.

Radiation-induced segregation in desensitized type 304 austenitic stainless steel

International Nuclear Information System (INIS)

Ahmedabadi, Parag; Kain, V.; Arora, K.; Samajdar, I.; Sharma, S.C.; Bhagwat, P.

2011-01-01

Graphical abstract: Schematic representation of overall experimental and results, indicating attack, after the DL-EPR test, on grain boundaries, twin boundaries and pit-like features within grains at the depth of maximum attack. The sensitized specimen also showed severe attack on grain boundaries, however, attack on twin-boundaries and pit-like features were not noticed. Display Omitted Highlights: → Characterization of radiation-induced segregation done by EPR and AFM examination. → Cr depletion adjacent to carbides due to RIS in irradiated desensitized 304 SS. → Effectiveness as defect sink: twins > pit-like features > grain boundary. - Abstract: Radiation-induced segregation (RIS) in desensitized type 304 stainless steel (SS) was investigated using a combination of electrochemical potentiokinetic reactivation (EPR) test and atomic force microscopy (AFM). Desensitized type 304 SS was irradiated to 0.43 dpa (displacement per atom) using 4.8 MeV protons at 300 deg. C. The maximum attack in the EPR test for the irradiated desensitized SS was measured at a depth of 70 μm from the surface. Grain boundaries and twin boundaries got attacked and pit-like features within the grains were observed after the EPR test at the depth of 70 μm. The depth of attack, as measured by AFM, was higher at grain boundaries and pit-like features as compared to twin boundaries. It has been shown that the chromium depletion due to RIS takes place at the carbide-matrix as well as at the carbide-carbide interfaces at grain boundaries. The width of attack at grain boundaries after the EPR test of the irradiated desensitized specimen appeared larger due to the dislodgement of carbides at grain boundaries.

Radiation-induced segregation in desensitized type 304 austenitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Ahmedabadi, Parag, E-mail: adit@barc.gov.in [Materials Science Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Kain, V. [Materials Science Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Arora, K. [PEC University of Technology, Chandigarh (India); Samajdar, I. [Department of Metallurgical Engineering and Materials Science, Indian Institute Technology Bombay, Powai, Mumbai 400 076 (India); Sharma, S.C.; Bhagwat, P. [Nuclear Physics Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India)

2011-09-30

Graphical abstract: Schematic representation of overall experimental and results, indicating attack, after the DL-EPR test, on grain boundaries, twin boundaries and pit-like features within grains at the depth of maximum attack. The sensitized specimen also showed severe attack on grain boundaries, however, attack on twin-boundaries and pit-like features were not noticed. Display Omitted Highlights: > Characterization of radiation-induced segregation done by EPR and AFM examination. > Cr depletion adjacent to carbides due to RIS in irradiated desensitized 304 SS. > Effectiveness as defect sink: twins > pit-like features > grain boundary. - Abstract: Radiation-induced segregation (RIS) in desensitized type 304 stainless steel (SS) was investigated using a combination of electrochemical potentiokinetic reactivation (EPR) test and atomic force microscopy (AFM). Desensitized type 304 SS was irradiated to 0.43 dpa (displacement per atom) using 4.8 MeV protons at 300 deg. C. The maximum attack in the EPR test for the irradiated desensitized SS was measured at a depth of 70 {mu}m from the surface. Grain boundaries and twin boundaries got attacked and pit-like features within the grains were observed after the EPR test at the depth of 70 {mu}m. The depth of attack, as measured by AFM, was higher at grain boundaries and pit-like features as compared to twin boundaries. It has been shown that the chromium depletion due to RIS takes place at the carbide-matrix as well as at the carbide-carbide interfaces at grain boundaries. The width of attack at grain boundaries after the EPR test of the irradiated desensitized specimen appeared larger due to the dislodgement of carbides at grain boundaries.

Application of Box–Behnken design for fabrication of titanium alloy and 304 stainless steel joints with silver interlayer by diffusion bonding

International Nuclear Information System (INIS)

Balasubramanian, M.

2015-01-01

Highlights: • Diffusion bonding of Ti–6Al–4V to SS304 with silver interlayer was successful. • Hardness and shear strength increased with the increase in the bonding temperature. • Shear strength of 149 MPa and 18% strain to failure were achieved. • Joint efficiency of 80% was obtained for the Ti–6Al–4V and SS304L joints. - Abstract: Direct bonding between titanium (Ti)/titanium alloy(Ti alloy) and stainless steel (SS) promotes the formation of various Fe–Ti and Fe–Cr–Ti intermetallics in the diffusion zone, because the solid solubility of Fe, Cr, Ni and Ti in each other is limited and these intermetallics weaken the mechanical properties of the joint. The present study focuses on the titanium alloy Ti–6Al–4V diffusion bonded to AISI 304 stainless steel with silver foil as an interlayer. The process parameters were chosen appropriately and hence, the bonding is achieved without any defect. Box–Behnken design is used to decide the optimum number of experiments required to do the investigation. Microhardness measurements and the lap shear test were carried out to determine the hardness and strength of the joints respectively. The results show that atomic diffusion and migration between Ti and Fe or C are effectively prevented by adding pure Ag as the interlayer metal. The results from mechanical testing showed that shear strength values have a direct relationship with bonding time. The maximum lap shear strength of 149 MPa and 18% strain to failure was observed for joints obtained with bonding time of 60 min. However, effective bonding was not possible at 850 °C due to incomplete coalescence of mating surfaces

Twin boundary cavitation in aged type 304 stainless steel

International Nuclear Information System (INIS)

Sikka, V.K.; Swindeman, R.W.; Brinkman, C.R.

1975-10-01

A transition from grain to twin boundary cavitation was observed in aged-and-creep-tested type 304 stainless steel. Evidence of twin boundary cavitation has also been observed for unaged material under certain test conditions. This same behavior was also found in aged type 316 stainless steel. Several possible reasons have been suggested for the absence of frequently observed grain boundary cavitation

41 CFR 101-5.304 - Type of occupational health services.

Science.gov (United States)

2010-07-01

... employees to maintain personal health; and (3) To provide specific disease screening examinations and... FEDERAL BUILDINGS AND COMPLEXES 5.3-Federal Employee Health Services § 101-5.304 Type of occupational... service unit, whether or not such injury was sustained by the employee while in the performance of duty or...

41 CFR 304-3.3 - May my agency or I accept payment for travel expenses to a meeting from a non-Federal source?

Science.gov (United States)

2010-07-01

... RESPONSIBILITY General § 304-3.3 May my agency or I accept payment for travel expenses to a meeting from a non... 41 Public Contracts and Property Management 4 2010-07-01 2010-07-01 false May my agency or I accept payment for travel expenses to a meeting from a non-Federal source? 304-3.3 Section 304-3.3 Public...

46 CFR 11.304 - Substitution of training for required service, use of training-record books, and use of towing...

Science.gov (United States)

2010-10-01

... training-record books, and use of towing officer assessment records. 11.304 Section 11.304 Shipping COAST... of training-record books, and use of towing officer assessment records. (a) Satisfactory completion... training of a candidate must be documented in a Coast Guard-accepted training-record book. (f) Except as...

Prediction of δ-ferrite distribution in continuously cast type 304 stainless steel slabs by diffusion transformation analysis

International Nuclear Information System (INIS)

Kim, J. Joon; Kim, Sun K.; Kim, Jong W.

1998-01-01

Retained δ-ferrite in 304 stainless steel is known to prevent hot cracking during continuous casting. Excess content of retained δ-ferrite lowers the hot workability. So it is necessary to control the amount of retained δ-ferrite in stainless steel. A numerical model based on coupled analysis of macro heat transfer and micro diffusion transformation has been developed in order to predict retained δ-ferrite in continuously cast 304 stainless steel slab. The finite difference technique for moving boundary problem has been formulated utilizing 'murray-landis variable-grid method'. The reliability of numerical model is compared with the other results. The prediction of δ-ferrite content in CC type 304 stainless steel slabs shows good agreement between measured and predicted results. Effect of secondary cooling condition on the δ-ferrite has been also investigated

[Interfering effects of radix Salviae miltiorrhizae and lingustrazine on mm-LDL activating BKCa in ECV304 cell].

Science.gov (United States)

Lin, L; Zheng, Y F; Qu, J H; Bao, G H

2001-08-01

To observe the action of minimally modified low density lipoprotein (mm-LDL) on BKCa in ECV304 cell and the interfering effects of radix salviae miltiorrhizae extract powder 764-3 (30 micrograms/ml) and lingustrazine (200 micrograms/ml) on this action. The cell-attached configuration of patch clamp technique was applied. mm-LDL (100 micrograms/ml) potentiated the activity of BKCa in ECV304. While 764-3 and lingustrazine abolished it. mm-LDL acted on vascular endothelial cell ECV304 could rapidly activate the activity of BKCa and might result in the increase of electro-chemical gradient for the resting Ca2+ influx, thus resting cytoplasmic concentration of calcium could be elevated and endothelial dysfunction would be induced. 764-3 and lingustrazine might have the protective action through decreasing the activity of BKCa.

Topological characterization of static strain aging of type AISI 304 austenitic stainless steel

International Nuclear Information System (INIS)

Monteiro, S.N.; Miranda, P.E.V. de

1981-01-01

Static strain aging of type AISI 304 austenitic stainless steel was studied from room temperature up to 623K by conducting tests in which the load was held approximately constant. The aging times varied between 10s and 100h, using a plastic pre-deformation of 9%. The static strain aging of 304 steel furnished an activation energy of 23.800 cal/mol. This implies that vacancies play an important role on the aging process. The curve of the variation of the discontinuous yielding with aging time presented different stages, to which specific mathematical expressions were developed. These facts permited the conclusion that Snock type mechanisms are responsible for the aging in such conditions. (Author) [pt

Some mechanical properties of borided AISI H13 and 304 steels

International Nuclear Information System (INIS)

Taktak, Sukru

2007-01-01

In the present study, mechanical properties of borides formed on AISI H13 hot work tool and AISI 304 stainless steels have been investigated. Both steels have high chromium content and have a widespread use in the engineering application. Boriding treatment was carried out in slurry salt bath consisting of borax, boric acid, and ferrosilicon at temperature range of 800-950 deg. C for 3, 5, and 7 h. X-ray diffraction analysis of boride layers on the surface of steels revealed various peaks of FeB, Fe 2 B, CrB, and Ni 3 B. Metallographic studies showed that the boride layer has a flat and smooth morphology in the 304 steel while H13 steel was a ragged morphology. The characterization of the boride layer is also carried out by means of the micro-hardness, surface roughness, adhesion, and fracture toughness studies

5 CFR 630.304 - Accumulation limitation for part-time employees.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Accumulation limitation for part-time... REGULATIONS ABSENCE AND LEAVE Annual Leave § 630.304 Accumulation limitation for part-time employees. A part-time employee may accumulate not more than 240 or 360 hours' annual leave on the same basis that a full...

Investigation of the influential parameters of machining of AISI 304 ...

Indian Academy of Sciences (India)

application of cutting fluid results in longer tool life and better surface finish. ... parameters for turning of AISI 304 stainless steel by considering the process ... In the design of experiments (DOE) the full factorial method was used in .... Esme U 2009 Application of Taguchi method for the optimization of resistance spot welding.

17 CFR 300.304 - Retained rights of brokers or dealers.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Retained rights of brokers or... Completion of Open Contractual Commitments § 300.304 Retained rights of brokers or dealers. (a) Nothing stated in these rules shall be construed to prejudice the right of a broker or dealer to any claim...

Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

Energy Technology Data Exchange (ETDEWEB)

Hartwig, A.; Decker, M.; Klein, O.; Karl, H., E-mail: helmut.karl@physik.uni-augsburg.de

2015-12-15

The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO{sub 2} implanted AISI 304 – examined for different implantation and annealing parameters – is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 10{sup 16} cm{sup −2} (Ti{sup +}) and 1 × 10{sup 17} cm{sup −2} (O{sup +}) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 10{sup 15} cm{sup −2} (Ti{sup +}) and 1 × 10{sup 16} cm{sup −2} (O{sup +}). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO{sub 2} inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

A força de atrito em braquetes plásticos e de aço inoxidável com a utilização de quatro diferentes tipos de amarração Frictional forces in stainless steel and plastic brackets using four types of wire ligation

Directory of Open Access Journals (Sweden)

Vanessa Nínia Correia Lima

2010-04-01

Full Text Available OBJETIVO: a finalidade deste estudo in vitro foi avaliar e comparar a resistência friccional em braquetes de aço inoxidável e de policarbonato compósito amarrados com fio metálico e elastômeros. MÉTODOS: foram utilizados quatro braquetes de aço inoxidável e quatro de policarbonato compósito (PC para pré-molares levados à máquina universal de ensaio mecânico para a tração de um segmento de fio de aço inoxidável 0,019" x 0,025" na velocidade de 0,5mm/min, com 8mm de deslocamento total. A forma de amarração variou entre as seguintes possibilidades: amarração metálica com pinça de Steiner, metálica com pinça Mathieu, elastômero da marca Morelli e elastômero da marca TP Orthodontics. RESULTADOS E CONCLUSÕES: os módulos elastoméricos geraram mais atrito do que os metálicos e a amarração com pinça Mathieu provocou menor atrito quando comparada a todas as situações avaliadas. Os braquetes de PC geraram menor atrito do que os metálicos, porém, na escolha do material a ser utilizado na clínica, outras variáveis - tais como a resistência ao cisalhamento e à fratura, a estabilidade de cor e a aderência por microrganismos - devem ser consideradas.OBJECTIVE: This in vitro study evaluated and compared the frictional resistance of stainless steel and polycarbonate (PC composite brackets tied with metal wire and elastomeric ligation. METHODS: Four stainless steel and four polycarbonate composite brackets for premolars were placed in a universal testing machine for the traction of a piece of 0.019 x 0.025-in wire at 0.5 mm/min and total displacement of 8 mm. Ligations were performed according to the following alternatives: metal ligation with Steiner tying pliers; metal ligation using Mathieu tying pliers; Morelli™ elastomeric ligation; and TP Orthodontics™ elastomeric ligation. RESULTS AND CONCLUSIONS: Elastomeric modules generated more friction than the metal ligations, and the ligation with the Mathieu tying

21 CFR 201.304 - Tannic acid and barium enema preparations.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Tannic acid and barium enema preparations. 201.304... Tannic acid and barium enema preparations. (a) It has become a widespread practice for tannic acid to be added to barium enemas to improve X-ray pictures. Tannic acid is capable of causing diminished liver...

Estudio de la corrosión de diferentes aleaciones en sales de carbonatos fundidos con la técnica de espectroscopía de impedancia electroquímica

Directory of Open Access Journals (Sweden)

Pérez, F. J.

2000-06-01

Full Text Available In the present work the corrosion behavior of different alloys (AISI 304, AISI 430 and TiAl6V in molten carbonates at 650EC are compared. By using the Electrochemical Impedance Technique different corrosion parameters such as the corrosion rate and the oxyde concentration and others features of the different layers of corrosion products are "in situ" determined. Take into account, the corrosion product characterization by X-ray Diffraction (XRD, Scanning Electron Microscopy (SEM and Electrochemical impedance Spectroscopy (EIS a corrosion mechanism for every tested alloy is proposed. In all cases, the corrosion mechanisms during the first hours are similar to a high temperature oxidation mechanism. When the equilibrium is established, the lithiation began by the formation of different double-layers on the surface of Li-metal oxydes. At the end of the corrosion process, one or two inner layers of metallic oxydes and one or two outer layers of Li-metal oxydes were formed. The corrosion mechanisms of the stainless steels (AISI 304 ans AISI 310S are a function of their chromium contents. TiAl6V alloy showed the best behavior against the corrosion of molten carbonates by the formation of a protective layer of mixed Li-Ti oxydes.

En el presente trabajo se compara el comportamiento frente a la corrosión de diferentes aleaciones (aceros inoxidables AISI 304 y AISI 310S y aleación TiAl6V en un electrolito de carbonatos fundidos a 650°C. Con la técnica de impedancia se determina “in situ” la velocidad de corrosión de las aleaciones, la resistencia del electrolito, es decir, la concentración del óxido disuelto y otras características de las capas de productos de corrosión. Teniendo en cuenta la caracterización de los productos de corrosión mediante difracción de rayos X (XRD y microscopía electrónica de barrido (SEM y los resultados de espectroscopía de impedancia (EIS, se propone un mecanismo para cada una de las aleaciones. En

Results of fracture mechanics tests on PNC SUS 304 plate

International Nuclear Information System (INIS)

Mills, W.J.; James, L.A.; Blackburn, L.D.

1985-08-01

PNC provided SUS 304 plate to be irradiated in FFTF at about 400 0 C to a target fluence of 5 x 10 21 n/cm 2 (E > 0.1 MeV). The actual irradiation included two basically different exposure levels to assure that information would be available for the exposure of interest. After irradiation, tensile properties, fatigue-crack growth rates and J-integral fracture toughness response were determined. These same properties were also measured for the unirradiated material so radiation damage effects could be characterized. This report presents the results of this program. It is expected that these results would be applicable for detailed fracture analysis of reactor components. Recent advances in elastic-plastic fracture mechanics enable reasonably accurate predictions of failure conditions for flawed stainless steel components. Extensive research has focused on the development of J-integral-based engineering approach for assessing the load carrying capacity of low-strength, high-toughness structural materials. Furthermore, Kanninen, et al., have demonstrated that J-integral concepts can accurately predict the fracture response for full-scale cracked structures manufactured from Type 304 stainless steel

The present-day chemical composition of the SMC from UVES spectra of the sharp-lined, B-type dwarf AV 304

NARCIS (Netherlands)

Rolleston, WRJ; Venn, K; Tolstoy, E; Dufton, PL

High-resolution spectroscopic VLT/UVES observations are presented for the B-type main-sequence star, AV 304, in the Small Magellanic Cloud (SMC). These spectra have been analysed using LTE model-atmosphere techniques, to derive stellar atmospheric parameters and chemical compositions. As AV 304 is

42 CFR 412.304 - Implementation of the capital prospective payment system.

Science.gov (United States)

2010-10-01

... HEALTH AND HUMAN SERVICES MEDICARE PROGRAM PROSPECTIVE PAYMENT SYSTEMS FOR INPATIENT HOSPITAL SERVICES Prospective Payment System for Inpatient Hospital Capital Costs General Provisions § 412.304 Implementation of the capital prospective payment system. (a) General rule. As described in §§ 412.312 through 412.370...

41 CFR 101-39.304 - Modification or installation of accessory equipment.

Science.gov (United States)

2010-07-01

..., TRANSPORTATION, AND MOTOR VEHICLES 39-INTERAGENCY FLEET MANAGEMENT SYSTEMS 39.3-Use and Care of GSA Interagency Fleet Management System Vehicles § 101-39.304 Modification or installation of accessory equipment. The modification of a GSA Interagency Fleet Management System (IFMS) vehicle or the permanent installation of...

Influence of sodium on the low-cycle fatigue behavior of types 304 and 316 stainless steel

International Nuclear Information System (INIS)

Smith, D.L.; Zeman, G.J.; Natesan, K.; Kassner, T.F.

1976-01-01

Fatigue tests in sodium were conducted to investigate the influence of a high-temperature sodium environment on the low-cycle fatigue behavior of Types 304 and 316 stainless steel. The effects of testing in a sodium environment as well as long-term sodium exposure were investigated. The fatigue tests were conducted at 600 and 700 0 C in sodium of controlled purity, viz., approximately 1 ppM oxygen and 0.4 ppM carbon, at a strain rate of 4 x 10 -3 s -1 . The fatigue life of annealed Type 316 stainless steel is substantially greater in sodium than when tested in air; however, the fatigue life of annealed Type 304 stainless steel is altered much less when tested in sodium. A 1512-h preexposure to sodium had no significant effect on the fatigue life of Type 316 stainless steel tested in sodium. However, a similar exposure substantially increased the fatigue life of Type 304 stainless steel in sodium. 10 fig

Fine grained 304 ASS processed by a severe plastic deformation and subsequent annealing; microstructure and mechanical properties evaluation

Science.gov (United States)

Salout, Shima Ahmadzadeh; Shirazi, Hasan; Nili-Ahmadabadi, Mahmoud

2018-01-01

The current research is an attempt to study the effect of a novel severe plastic deformation technique so called "repetitive corrugation and straightening by rolling" (RCSR) and subsequent annealing on the microstructure and mechanical properties of AISI type 304 austenitic stainless steel. In this study, RCSR process was carried out at 200 °C on the 304 austenitic stainless steel (above Md30 temperature that is about 50 °C for this stainless steel) in order to avoid the formation of martensite phase when a high density of dislocations was introduced into the austenite phase and also high density of mechanical twins was induced in the deformed 304 austenitic stainless steel. Because of relationship between deformation temperature, stacking fault energy (SFE) and mechanisms of deformation. Thereafter subsequently, annealing treatment was applied into deformed structure in order to refine the microstructure of 304 stainless s teel. The specimens were examined by means of optical microscopy (OM), scanning electron microscopy (SEM), tensile and micro-hardness tests. The results indicate that by increasing the cycles of RCSR process (increasing applied strain), further mechanical twins are induced, the hardness and in particular, the yield stress of specimens have been increased.

Caracterización mecánica de recubrimientos de aluminio por CVD-FBR sobre aceros inoxidables y resistencia a la oxidación en vapor de agua

Directory of Open Access Journals (Sweden)

Diego Pérez-Muñoz

2015-09-01

Full Text Available Los recubrimientos de aluminio depositados sobre el acero inoxidable austenítico AISI 317 por Deposición Química de Vapor en Lecho Fluidizado (CVD-FBR presentan a altas temperaturas una reducción de la velocidad de corrosión de más de 80 veces. Se realizó la caracterización mecánica de los recubrimientos por medio de microdureza, nanoindentación, para conocer cómo se vieron afectas las propiedades mecánicas (en especial la dureza y el módulo de Young del recubrimiento y del sustrato luego de ser sometidos a la oxidación a alta temperatura. También se hicieron análisis por medio de Microscopia Electrónica de Barrido (MEB, para observar los cambios microestructurales, y de Microscopia de Fuerza Atómica (MFA, para observar cómo varía la topografía y el gradiente de rugosidad en función de la distancia recorrida por la punta del cantiléver durante los barridos.

Preliminary lifetime predictions for 304 stainless steel as the LANL ABC blanket material

International Nuclear Information System (INIS)

Park, J.J.; Buksa, J.J.; Houts, M.G.; Arthur, E.D.

1997-11-01

The prediction of materials lifetime in the preconceptual Los Alamos National Laboratory (LANL) Accelerator-Based Conversion of Plutonium (ABC) is of utmost interest. Because Hastelloy N showed good corrosion resistance to the Oak Ridge National Laboratory Molten Salt Reactor Experiment fuel salt that is similar to the LANL ABC fuel salt, Hastelloy N was originally proposed for the LANL ABC blanket material. In this paper, the possibility of using 304 stainless steel as a replacement for the Hastelloy N is investigated in terms of corrosion issues and fluence-limit considerations. An attempt is made, based on the previous Fast Flux Test Facility design data, to predict the preliminary lifetime estimate of the 304 stainless steel used in the blanket region of the LANL ABC

Mechanical Behaviour of 304 Austenitic Stainless Steel Processed by Room Temperature Rolling

Science.gov (United States)

Singh, Rahul; Goel, Sunkulp; Verma, Raviraj; Jayaganthan, R.; Kumar, Abhishek

2018-03-01

To study the effect of room temperature rolling on mechanical properties of 304 Austenitic Stainless Steel, the as received 304 ASS was rolled at room temperature for different percentage of plastic deformation (i.e. 30, 50, 70 and 90 %). Microstructural study, tensile and hardness tests were performed in accordance with ASTM standards to study the effect of rolling. The ultimate tensile strength (UTS) and hardness of a rolled specimen have enhanced with rolling. The UTS has increased from 693 MPa (as received) to 1700 MPa (after 90% deformation). The improvement in UTS of processed samples is due to combined effect of grain refinement and stress induced martensitic phase transformation. The hardness values also increases from 206 VHN (as received) to 499 VHN (after 90% deformation). Magnetic measurements were also conducted to confirm the formation of martensitic phase.

Influence of Fretting on Flexural Fatigue of 304 Stainless Steel and Mild Steel

National Research Council Canada - National Science Library

Bill, Robert

1978-01-01

Fretting fatigue experiments conducted on 304 stainless steel using a flexural-fatigue test arrangement with bolted-on fretting pads have demonstrated that fatigue life is reduced by at least a factor...

XPS STRUCTURE ANALYSIS OF TiN/TiC BILAYERS PRODUCED BY PULSED VACUUM ARC DISCHARGE

Directory of Open Access Journals (Sweden)

ELISABETH RESTREPO PARRA

2010-01-01

Full Text Available se crecieron bicapas de TiN/TiC sobre sustratos de acero inoxidable 304 usando un sistema de deposición física de vapor asistida por plasma en forma de arco pulsado a dos diferentes temperaturas del sustrato (50º C y150º C. Para el análisis de la composición química se empleó la técnica de la espectroscopía de fotoelectrones de rayos X (XPS. Se observó el comportamiento de las líneas Ti2p, N1s y C1s. Los análisis de energía de enlace confirmaron la conformación de TiN y TiC. Los picos C1s y Ti2p sufrieron un corrimiento a medida que se incrementó el tiempo de esputtering, revelando contaminación debido a la presencia de hidrocarburos. Además, los perfiles de profundidad de las bicapas de TiN/TiC mostraron que las películas crecidas a una temperatura de 150 ° C tienen una capa de TiN más gruesa que las muestras crecidas a 50º C. El nitrógeno se difundió en la capa de TiC y el carbón en la capa de TiN para ambas temperaturas.

45 CFR 304.22 - Federal financial participation in purchased support enforcement services.

Science.gov (United States)

2010-10-01

... FAMILIES, DEPARTMENT OF HEALTH AND HUMAN SERVICES FEDERAL FINANCIAL PARTICIPATION § 304.22 Federal financial participation in purchased support enforcement services. Federal financial participation is.... Support enforcement services which may be purchased with Federal financial participation are those for...

24 CFR 983.304 - Other subsidy: effect on rent to owner.

Science.gov (United States)

2010-04-01

... URBAN DEVELOPMENT PROJECT-BASED VOUCHER (PBV) PROGRAM Rent to Owner § 983.304 Other subsidy: effect on...) Subsidized projects. (1) This paragraph (c) applies to any contract units in any of the following types of... non-insured Section 236 project that continues to receive Interest Reduction Payment following a...

Effect of cold working on nitriding process of AISI 304 and 316 austenitic stainless steel

International Nuclear Information System (INIS)

Pereira, Silvio Andre de Lima

2012-01-01

The nitriding behavior of AISI 304 and 316 austenitic stainless steel was studied by different cold work degree before nitriding processes. The microstructure, thickness, microhardness and chemical micro-composition were evaluated through optical microscopy, microhardness, scanner electronic microscopy and x ray diffraction techniques. Through them, it was observed that previous plastic deformations do not have influence on layer thickness. However, a nitrided layer thicker can be noticed in the AISI 304 steel. In addition, two different layers can be identified as resulted of the nitriding, composed for austenitic matrix expanded by nitrogen atoms and another thinner immediately below expanded by Carbon atoms. (author)

Instability predictions for circumferentially cracked Type-304 stainless-steel pipes under dynamic loading. Final report

International Nuclear Information System (INIS)

Zahoor, A.; Wilkowski, G.; Abou-Sayed, I.; Marschall, C.; Broek, D.; Sampath, S.; Rhee, H.; Ahmad, J.

1982-04-01

This report provides methods to predict margins of safety for circumferentially cracked Type 304 stainless steel pipes subjected to applied bending loads. An integrated combination of experimentation and analysis research was pursued. Two types of experiments were performed: (1) laboratory-scale tests on center-cracked panels and bend specimens to establish the basic mechanical and fracture properties of Type 304 stainless steel, and (2) full-scale pipe fracture tests under quasi-static and dynamic loadings to assess the analysis procedures. Analyses were based upon the simple plastic collapse criterion, a J-estimation procedure, and elastic-plastic large-deformation finite element models

Comparación entre los diagramas TTS obtenidos mediante los ensayos normalizados Huey y Strauss modificado para el acero inoxidable AISI 304

Directory of Open Access Journals (Sweden)

Otero, E.

1996-04-01

Full Text Available This work presents a comparison of Temperature-Time-Sensitization TTS diagrams obtained by Huey and modified Strauss standard, for detecting susceptibility to intergranular attack. The difference between these tests is the use of a strong or a slightly smooth oxidizing electrolyte. The diagrams obtained are different and if a sample tested by modified Strauss is sensitized, then it will be sensitized in the Huey test, but the contrary is not always true. This difference is because a sensitized sample has to have a continuous band lacking in chromium along the grain boundary in order to be sensitized in the modified Strauss test. This condition is not necessary in the Huey test.

Se comparan los diagramas Temperatura-Tiempo-Sensibilización TTS, obtenidos mediante los ensayos normalizados de corrosión intergranular Huey y Strauss modificado, que, respectivamente, utilizan electrólitos fuerte y suavemente oxidantes, mostrándose que los diagramas obtenidos son diferentes. Si una muestra evaluada mediante el ensayo Strauss modificado se encuentra sensibilizada, entonces lo estará también en el ensayo Huey, pero no necesariamente ocurrirá lo contrario; esta diferencia se asocia a la necesidad de la existencia de una zona continua empobrecida en cromo a lo largo del límite de grano para que el material se sensibilice con respecto al ensayo Strauss modificado, condición innecesaria para el caso del ensayo Huey.

10 CFR 431.304 - Uniform test method for the measurement of energy consumption of walk-in coolers and walk-in...

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Uniform test method for the measurement of energy consumption of walk-in coolers and walk-in freezers. 431.304 Section 431.304 Energy DEPARTMENT OF ENERGY... measuring, pursuant to EPCA, the energy consumption of refrigerated bottled or canned beverage vending...

Identification of two immortalized cell lines, ECV304 and bEnd3, for in vitro permeability studies of blood-brain barrier.

Directory of Open Access Journals (Sweden)

Shu Yang

Full Text Available To identify suitable cell lines for a mimetic system of in vivo blood-brain barrier (BBB for drug permeability assessment, we characterized two immortalized cell lines, ECV304 and bEnd3 in the respect of the tightness, tight junction proteins, P-glycoprotein (P-gp function and discriminative brain penetration. The ECV304 monoculture achieved higher transendothelial electrical resistance (TEER and lower permeability to Lucifer yellow than bEnd3. However, co-culture with rat glioma C6 cells impaired the integrity of ECV304 and bEnd3 cell layers perhaps due to the heterogeneity among C6 cells in inducing BBB characteristics. The immunostaining of ZO-1 delivered distinct bands along cell borders on both cell lines while those of occludin and claudin-5 were diffused and weak. P-gp functionality was only proved in bEnd3 by Rhodamine 123 (R123 uptake assay. A permeability test of reference compounds displayed a similar rank order (digoxin < R123 < quinidine, verapamil < propranolol in ECV304 and bEnd3 cells. In comparison with bEnd3, ECV304 developed tighter barrier for the passage of reference compounds and higher discrimination between transcellular and paracellular transport. However, the monoculture models of ECV304 and bEnd3 fail to achieve the sufficient tightness of in vitro BBB permeability models with high TEER and evident immunostaining of tight junction proteins. Further strategies to enhance the paracellular tightness of both cell lines to mimic in vivo BBB tight barrier deserve to be conducted.

12 CFR 1806.304 - Books of account, records and government access.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Books of account, records and government access..., DEPARTMENT OF THE TREASURY BANK ENTERPRISE AWARD PROGRAM Terms and Conditions of Assistance § 1806.304 Books... to the Awardee's offices and facilities, and all books, documents, records, and financial statements...

41 CFR 101-27.304-1 - Establishment of economic retention limit.

Science.gov (United States)

2010-07-01

... in the GSA Handbook, The Economic Order Quantity Principle and Applications. The handbook is listed... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Establishment of economic... MANAGEMENT 27.3-Maximizing Use of Inventories § 101-27.304-1 Establishment of economic retention limit. An...

A Study on the Characteristics of Corrosion in Cold Worked Flexible STS 304 Stainless Steel Pipes

International Nuclear Information System (INIS)

Kim, In Soo; Kim, Sung Jin

1993-01-01

Effects of cold working on the corrosion resistance of austenitic STS 304 stainless steel pipes were investigated using anodic polarization method, EDX analysis and SEM technique. Corrosion products had a lots of S and Cl - ion. Generally, corrosion patterns as a result of STS 304 stainless steel to concrete environment were proceeded in the order of the pitting to intergranular corrosion. In the case of the flexible pipes were covered tightly with other polymer materials, crevice corrosion occurred to a much greater extent on austenitic than on martensitic region

The Seahorse Nebula: New views of the filamentary infrared dark cloud G304.74+01.32 from SABOCA, Herschel, and WISE

Science.gov (United States)

Miettinen, O.

2018-02-01

Context. Filamentary molecular clouds, such as many of the infrared dark clouds (IRDCs), can undergo hierarchical fragmentation into substructures (clumps and cores) that can eventually collapse to form stars. Aims: We aim to determine the occurrence of fragmentation into cores in the clumps of the filamentary IRDC G304.74+01.32 (hereafter, G304.74). We also aim to determine the basic physical characteristics (e.g. mass, density, and young stellar object (YSO) content) of the clumps and cores in G304.74. Methods: We mapped the G304.74 filament at 350 μm using the Submillimetre APEX Bolometer Camera (SABOCA) bolometer. The new SABOCA data have a factor of 2.2 times higher resolution than our previous Large APEX BOlometer CAmera (LABOCA) 870 μm map of the cloud (9″ vs. 19\\farcs86). We also employed the Herschel far-infrared (IR) and submillimetre, and Wide-field Infrared Survey Explorer (WISE) IR imaging data available for G304.74. The WISE data allowed us to trace the IR emission of the YSOs associated with the cloud. Results: The SABOCA 350 μm data show that G304.74 is composed of a dense filamentary structure with a mean width of only 0.18 ± 0.05 pc. The percentage of LABOCA clumps that are found to be fragmented into SABOCA cores is 36% ± 16%, but the irregular morphology of some of the cores suggests that this multiplicity fraction could be higher. The WISE data suggest that 65% ± 18% of the SABOCA cores host YSOs. The mean dust temperature of the clumps, derived by comparing the Herschel 250, 350, and 500 μm flux densities, was found to be 15.0 ± 0.8 K. The mean mass, beam-averaged H2 column density, and H2 number density of the LABOCA clumps are estimated to be 55 ± 10M⊙, (2.0 ± 0.2) × 1022 cm-2, and (3.1 ± 0.2) × 104 cm-3. The corresponding values for the SABOCA cores are 29 ± 3M⊙, (2.9 ± 0.3) × 1022 cm-2, and (7.9 ± 1.2) × 104 cm-3. The G304.74 filament is estimated to be thermally supercritical by a factor of ≳ 3.5 on the scale

Microstructure and mechanical properties of annealed SUS 304H austenitic stainless steel with copper

Energy Technology Data Exchange (ETDEWEB)

Sen, Indrani [Department of Materials Engineering, Indian Institute of Science, Bangalore 560012 (India); Amankwah, E. [Department of Materials Engineering, Indian Institute of Science, Bangalore 560012 (India); Department of Materials Science, African University of Science and Technology, Abuja (Nigeria); Kumar, N.S. [Department of Materials Engineering, Indian Institute of Science, Bangalore 560012 (India); Fleury, E. [Center for High Temperature Energy Materials, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Oh-ishi, K.; Hono, K. [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Ramamurty, U., E-mail: ramu@materials.iisc.ernet.in [Department of Materials Engineering, Indian Institute of Science, Bangalore 560012 (India)

2011-05-25

Research highlights: {yields} SUS 304H austenitic stainless steel containing 3 wt.% Cu was annealed at 700 deg. C for up to 100 h. {yields} Microstructure and mechanical properties of annealed alloys are examined. {yields} Nano-sized Cu-rich precipitation upon annealing. {yields} Strength of the alloy remains invariant with annealing whereas ductility improves. {yields} Fatigue crack growth threshold of 3 wt.% Cu added alloy increases with annealing. - Abstract: An experimental investigation into the effect of Cu on the mechanical properties of 0 and 3 wt.% Cu added SUS 304H austenitic stainless steel upon annealing at 700 deg. C for up to 100 h was conducted. Optical microscopy reveals grain coarsening in both the alloys upon annealing. Observations by transmission electron microscopy revealed the precipitation of nanometer-sized spherical Cu particles distributed within the austenitic grains and the presence of carbides at the dislocations. Both the yield and ultimate tensile strengths of the alloys were found to remain invariant with annealing. Tensile ductility and the threshold stress intensity factor range for fatigue crack growth for 3 wt.% Cu added alloy increase with annealing. These are attributed to the grain coarsening with annealing. In all, the addition of Cu to SUS 304H does not affect the mechanical performance adversely while improving creep resistance.

Soldadura TIG de los aceros inoxidables dúplex del tipo 22-05 (Uranus 45N y Avesta. Estudio de la microestructura y de las propiedades mecánicas

Directory of Open Access Journals (Sweden)

Gómez de Salazar, J. M.

1998-05-01

Full Text Available TIG welding of two different duplex stainless steels is carried out. Arc-discharge on base-material plates by means of the TIG technique without filler metal and varying the energetic conditions (E.N.A. has been performed, A comparative study concerning the microstructural evolution as well as mechanical properties is carried out, The relation between hardness profiles, the microstructural variations and the ferrita δ concentration is established. Further, the above mentioned properties are related to the E.N.A. for each welded joint.

Se estudia la soldadura TIG de dos aceros inoxidables dúplex. Para ello, se ha descargado un arco sobre las chapas de material base mediante la técnica TIG, sin aportación de material y variando las E.N.A. Se realiza un estudio comparativo de la evolución microestructural, así como de las propiedades mecánicas. Se establece la relación entre los perfiles de dureza obtenidos y la variación microestructural y de la concentración de ferrita δ, así como estas propiedades con el E.N.A, de cada cordón.

Caracterización y propiedades mecánicas a alta temperatura de un acero inoxidable dúplex

Directory of Open Access Journals (Sweden)

Jiménez, J. A.

1998-05-01

Full Text Available The microstructure and mechanical behavior at high temperature of a thermomechanical processed duplex stainless steel have been studied. Recrystalization of the material takes place during heating to test temperature, and a microstructure consisting of islands of austenitic grains of about 10-15 μm in size included in a more or less continuous matrix of ferrite is observed. Tensile tests at temperatures above 1,000°C and at low strain rates show a stress exponent of about 2 and elongations to failure up to 290 %. These values suggest that deformation is controlled by a grain boundary sliding mechanism, which causes a decrease in the size of the islands during deformation. Finally, an activation energy for plastic deformation of 167 kJ/mol was observed that was related to the activation energy for grain boundary diffusion of iron.

Se ha estudiado la microestructura y el comportamiento mecánico a alta temperatura de un acero inoxidable dúplex procesado termomecánicamente. Durante el calentamiento a la temperatura de ensayo, el material recristaliza y se obtiene una microestructura de granos austeníticos de tamaños comprendidos entre 10 y 15 μm agrupados en islas incluidas en una matriz más o menos continua de ferrita. Ensayos de tracción a temperaturas superiores a 1.000°C y bajas velocidades de deformación muestran un exponente de la tensión igual a 2 y alargamientos a rotura de hasta 290 %. Estos valores permiten asociar el mecanismo de deformación al deslizamiento de fronteras de grano, el cual determina la desaparición progresiva de las islas de granos austeníticos durante la deformación. Finalmente, se encontró un valor de 167 kJ/mol para la energía de activación de la deformación plástica, la cual se relacionó con la energía de autodifusión del hierro a lo largo de las fronteras de grano.

12 CFR 30.4 - Filing of safety and soundness compliance plan.

Science.gov (United States)

2010-01-01

... steps the bank will take to correct the deficiency and the time within which those steps will be taken. (c) Review of safety and soundness compliance plans. Within 30 days after receiving a safety and... AND SOUNDNESS STANDARDS § 30.4 Filing of safety and soundness compliance plan. (a) Schedule for filing...

Corrosion behaviour of AISI 304 stainless steel subjected to massive laser shock peening impacts with different pulse energies

International Nuclear Information System (INIS)

Lu, J.Z.; Qi, H.; Luo, K.Y.; Luo, M.; Cheng, X.N.

2014-01-01

Highlights: •Laser shock peening caused an obvious increase of corrosion resistance of 304 steel. •Corrosion resistance of stainless steel increased with increasing pulse energy. •Mechanism of laser shock peening on corrosion behaviour was also entirely determined. -- Abstract: Effects of massive laser shock peening (LSP) impacts with different pulse energies on ultimate tensile strength (UTS), stress corrosion cracking (SCC) susceptibility, fracture appearance and electrochemical corrosion resistance of AISI 304 stainless steel were investigated by slow strain rate test, potentiodynamic polarisation test and scanning electron microscope observation. The influence mechanism of massive LSP impacts with different pulse energies on corrosion behaviour was also determined. Results showed that massive LSP impacts effectively caused a significant improvement on UTS, SCC resistance, and electrochemical corrosion resistance of AISI 304 stainless steel. Increased pulse energy can also gradually improve its corrosion resistance

33 CFR 149.304 - What type and how many survival craft and rescue boats must a manned deepwater port have?

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false What type and how many survival craft and rescue boats must a manned deepwater port have? 149.304 Section 149.304 Navigation and... What type and how many survival craft and rescue boats must a manned deepwater port have? (a) Except as...

Caracterização microestrutural de soldas dissimilares dos aços ASTM A-508 e AISI 316L Characterization of dissimilar metal weld between low alloy steel ASTM A-508 and 316L stainless steel

Directory of Open Access Journals (Sweden)

Luciana Iglésias Lourenço Lima

2010-06-01

Full Text Available As soldas dissimilares (dissimilar metal welds - DMWs são utilizadas em diversos segmentos da indústria. No caso específico de usinas nucleares, tais soldas são necessárias para conectar tubulações de aço inoxidável com componentes fabricados em aços baixa liga. Os materiais de adição mais utilizados neste tipo de solda são as ligas de níquel 82 e 182. Este trabalho consistiu na soldagem de uma junta dissimilar de aço baixa liga ASTM A-508 G3 e aço inoxidável austenítico AISI 316L utilizando as ligas de níquel 82 e 182 como metais de adição. A soldagem foi realizada manualmente empregando os processos de soldagem ao arco SMAW (Shielded Metal Arc Welding e GTAW (Gas Tungsten Arc Welding. Os corpos de prova foram caracterizados microestruturalmente utilizando-se microscópio óptico e microscópio eletrônico de varredura com microanálise por dispersão de energia de raios X (EDS e ensaios de microdureza Vickers. Observou-se uma microestrutura constituída de dendritas de austenita com a presença de precipitados com formas e dimensões definidas pelo aporte térmico e pela direção de soldagem. Não houve variação significativa da dureza ao longo da junta soldada, demonstrando a adequação dos parâmetros de soldagem utilizados.The dissimilar metal welds (DMWs are used in several areas of the industries. In the nuclear power plant, this weld using nickel alloy welding wires is used to connect stainless steel pipes to low alloy steel components on the reactor pressured vessels. The filler materials commonly used in this type of weld are nickel alloys 82 and 182.. In this study, dissimilar metal welds composed of low alloy steel ASTM A-508 G3, nickel alloys 82 e 182 as weld metals, and austenitic stainless steel AISI 316L were prepared by manual shielded metal arc welding (SMAW and gas tungsten arc welding techniques (GTAW. Samples were microstructural characterized by optical microscopy and scanning electron microscopy

Separación selectiva de hierro y cromo de las lejías agotadas del decapado de acero inoxidable

Directory of Open Access Journals (Sweden)

Gálvez, J. L.

2005-12-01

Full Text Available Stainless steel spent pickling baths are very complex solutions of metals and acids (HNO₃ and HF and are a very important environmental concern. Several processes have been developed for acid recovery (free and bounded acid with techniques like acid retardation, solvent extraction, evaporation and dialysis diffusion. In these processes, metallic content is precipitated and treated for its disposal. We have developed a process that permits the separation of metals by means of a selective precipitation, induced by adding free fluoride. Iron (Fe and chromium (Cr precipitate as pentafluorides and nitrogennickel (Ni remains in solution. After this stage, complex fluorides can be hydrolized with alkali to give iron and chromium hydroxides, releasing fluoride in solution

Los baños ácidos agotados del decapado de acero inoxidable son disoluciones muy complejas debido al alto contenido de metales y ácidos (HNO₃ y HF, por lo que constituyen un grave problema medioambiental. Existen tratamientos comerciales para la recuperación del ácido (libre o complejado que se basan en técnicas de retardo ácido, extracción con disolventes, evaporación o membranas. En estos procesos el contenido metálico es precipitado y tratado como un residuo. El grupo de investigación formado por los autores del presente trabajo ha desarrollado un procedimiento que permite el aprovechamiento de dichos metales mediante su recuperación selectiva con una técnica de precipitación modificada inducida por fluoruro libre. Se consigue la precipitación de hierro (Fe y cromo (Cr como pentafluoruros (pH 3-4,5 dejando el níquel en disolución. Posteriormente, los fluoruros complejos son hidrolizados con álcali dando lugar a hidróxidos de hierro y cromo, mientras que el fluoruro es redisuelto.

Stress corrosion cracking of L-grade stainless steels in boiling water reactor (BWR) plants

International Nuclear Information System (INIS)

Suzuki, Shunichi; Fukuda, Toshihiko; Yamashita, Hironobu

2004-01-01

L-grade stainless steels as 316NG, SUS316L and SUS304L have been used for the BWR reactor internals and re-circulation pipes as SCC resistant materials. However, SCC of the L-grade material components were reported recently in many Japanese BWR plants. The detail investigation of the components showed the fabrication process such as welding, machining and surface finishing strongly affected SCC occurrence. In this paper, research results of SCC of L-grade stainless steels, metallurgical investigation of core shrouds and re-circulation pipings, and features of SCC morphology were introduced. Besides, the structural integrity of components with SCC, countermeasures for SCC and future R and D planning were introduced. (author)

CASK inhibits ECV304 cell growth and interacts with Id1

International Nuclear Information System (INIS)

Qi Jie; Su Yongyue; Sun Rongju; Zhang Fang; Luo Xiaofeng; Yang Zongcheng; Luo Xiangdong

2005-01-01

Calcium/calmodulin-dependent serine protein kinase (CASK) is generally known as a scaffold protein. Here we show that overexpression of CASK resulted in a reduced rate of cell growth, while inhibition of expression of endogenous CASK via RNA-mediated interference resulted in an increased rate of cell growth in ECV304 cells. To explore the molecular mechanism, we identified a novel CASK-interacting protein, inhibitor of differentiation 1 (Id1) with a yeast two-hybrid screening. Furthermore, endogenous CASK and Id1 proteins were co-precipitated from the lysates of ECV304 cells by immunoprecipitation. Mammalian two-hybrid protein-protein interaction assays indicated that CASK possessed a different binding activity for Id1 and its alternative splicing variant. It is known that Id proteins play important roles in regulation of cell proliferation and differentiation. Thus, we speculate that the regulation of cell growth mediated by CASK may be involved in Id1. Our findings indicate a novel function of CASK, the mechanism that remains to be further investigated

Refinement of the magnetic composite model of type 304 stainless steel by considering misoriented ferromagnetic martensite particles

Science.gov (United States)

Kinoshita, Katsuyuki

2017-05-01

We improved a magnetic composite model that combines the Jiles-Atherton model and Eshelby's equivalent inclusion method to consider misoriented martensite particles. The magnetic permeability of type 304 stainless steel were analyzed by using both experimental data on the orientation distribution of type 304 stainless steel specimens and the improved model. We found that the model is able to qualitatively explain the variation of permeability with the orientation angle and orientation distribution, an effect that depends on the direction of the excitation magnetic field.

Avaliação da soldagem multipasse de chapas espessas de aços inoxidáveis lean duplex UNS S32304 soldadas pelos processos SMAW, GMAW e FCAW: parte 1: propriedades mecânicas Evaluation of multipass welding of thick lean duplex stainless steel UNS S32304 plates welded by SMAW, GMAW and FCAW: part 1: Mechanical Properties

Directory of Open Access Journals (Sweden)

Ronaldo Cardoso Junior

2012-12-01

Full Text Available Os aços inoxidáveis duplex (AID vêm se apresentando como uma excelente alternativa para aplicações em que alta resistência à corrosão e alta resistência mecânica são requeridas. Contudo, os AID, incluindo os aços inoxidáveis lean duplex, apresentam soldabilidade inferior em relação aos aços inoxidáveis austeníticos. Nesse sentido, esse trabalho tem como objetivo a avaliação da soldagem multipasse de chapas 22 mm de espessura da liga inoxidável lean duplex UNS S32304, utilizando-se os processo SMAW, GMAW e FCAW e consumíveis com dois tipos de composição química, 22%Cr9%Ni3%Mo e 23%Cr7%Ni, totalizando seis experimentos. Foram empregados chanfros em V com 60º e suporte cerâmico para soldagem do passe de raiz, sendo que o aporte térmico foi mantido praticamente constante em 1,6 kJ.mm-1. Determinou-se os tempos de soldagem e a seqüência de passes, objetivando uma análise de produtividade, em seguida as juntas soldadas foram submetidas à END por raios x. Foram extraídos corpos de prova para ensaios de tração, dobramento, Charpy a -30 ºC e microdureza. A produtividade dos processos semi-automáticos se mostrou pelo menos 63 % maior que a do processo SMAW, enquanto o processo FCAW se mostrou de 6 a 18% mais rápido que o GMAW. Foram encontradas descontinuidades (porosidade consideradas aceitáveis segundo ASME B31.3 em alguns dos experimentos, que não influenciaram negativamente os resultados mecânicos, os quais se apresentaram acima requerimento do metal de base e especificado por normas de fabricação.The duplex stainless steels (DSS's have been placed as an excellent alternative for applications where high corrosion resistance and high mechanical strength are required. However, DSS's, including the lean duplex, present lower weldability than the austenitic stainless steels. Thus, this study aims to evaluate the multipass welding of 22 mm plates of lean duplex stainless steel alloy UNS S32304, using the process

Analysis of residual stresses in girth welded type 304 stainless steel pipes

International Nuclear Information System (INIS)

Brust, F.W.; Kanninen, M.F.

1981-01-01

Intergranular stress corrosion cracking (IGSCC) in boiling water reactor (BWR) piping is a problem for the nuclear power industry. Tensile residual stresses induced by welding are an important factor in IGSCC of Type 304 stainless steel pipes. Backlay and heat sink welding can retard IGSCC. 17 refs

10 CFR 490.304 - Which new light duty motor vehicles are covered.

Science.gov (United States)

2010-01-01

... Section 490.304 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM...) Exception. If a covered person has more than one affiliate, division, or other business unit, then section 490.302 of this part only applies to light duty motor vehicles newly acquired by an affiliate...

Influencia de la atmósfera de sinterización en las propiedades mecánicas de los aceros P/M AISI 430L

Directory of Open Access Journals (Sweden)

Iglesias, F. Javier

2014-03-01

Full Text Available It has studied the stainless steel powder metallurgy AISI 430L. It has compared the sintering in two different atmospheres; in vacuum, and in an atmosphere containing nitrogen. It has developed a heat treatment with the aim of improving the mechanical properties. This has been done through microstructural modification of complex nitrides of iron and chromium precipitates during the phase of sintering. Physical properties have been evaluated and are been performing a microstructural analysis for microstructure related to the increase in mechanical properties.Se ha estudiado el acero inoxidable pulvimetalúrgico AISI 430L, comparando la sinterización en dos atmósferas diferentes; en vacío, y en una atmósfera que contiene nitrógeno. Se ha desarrollado un tratamiento térmico con objeto de incrementar las propiedades mecánicas, mediante la modificación microestructural de los nitruros complejos de hierro y cromo precipitados durante la etapa de sinterización. Se han evaluado las propiedades físicas y a la vez se ha realizado un análisis microestructural con el fin de relacionar la microestructura con el incremento en las propiedades mecánicas.

Instability predictions for circumferentially cracked Type-304 stainless-steel pipes under dynamic loading. Final report. [BWR

Energy Technology Data Exchange (ETDEWEB)

Zahoor, A.; Wilkowski, G.; Abou-Sayed, I.; Marschall, C.; Broek, D.; Sampath, S.; Rhee, H.; Ahmad, J.

1982-04-01

This report provides methods to predict margins of safety for circumferentially cracked Type 304 stainless steel pipes subjected to applied bending loads. An integrated combination of experimentation and analysis research was pursued. Two types of experiments were performed: (1) laboratory-scale tests on center-cracked panels and bend specimens to establish the basic mechanical and fracture properties of Type 304 stainless steel, and (2) full-scale pipe fracture tests under quasi-static and dynamic loadings to assess the analysis procedures. Analyses were based upon the simple plastic collapse criterion, a J-estimation procedure, and elastic-plastic large-deformation finite element models.

Influence of ferritic phase on the localized corrosion in the AISI 304 type austenitic stainless steel

International Nuclear Information System (INIS)

Lombardi, C.C.M.; Ramanathan, L.V.

1994-01-01

The influence of adding up to 4.7 wt% Si to AISI 304 on the pitting corrosion resistance and intergranular corrosion resistance has been studied. The alloys were prepared by melting in a vacuum induction furnace and annealed at 1200 0 C for 1 hour followed by quenching. Prolonged immersion tests in Fe C L 3 and anodic polarization measurements in 3.5% NaCl revealed that with increasing Si the tendency of the alloy to pit decreased and the pitting potential increased. The susceptibility to intergranular corrosion as determined through Huey tests also decreased with Si content. The overall influence of Si in the alloy on the corrosion behaviour is considered to be due to incorporation of Si in the surface film and consequent improvement in adhesion as well as reduction in detects within the film. (author). 7 refs, 4 figs, 6 tabs

Comparison of Mg-based multilayers for solar He II radiation at 30.4 nm wavelength

Energy Technology Data Exchange (ETDEWEB)

Zhu Jingtao; Zhou Sika; Li Haochuan; Huang Qiushi; Wang Zhanshan; Le Guen, Karine; Hu, Min-Hui; Andre, Jean-Michel; Jonnard, Philippe

2010-07-10

Mg-based multilayers, including SiC/Mg, Co/Mg, B4C/Mg, and Si/Mg, are investigated for solar imaging and a He II calibration lamp at a 30.4 nm wavelength. These multilayers were fabricated by a magnetron sputtering method and characterized by x-ray reflection. The reflectivities of these multilayers were measured by synchrotron radiation. Near-normal-incidence reflectivities of Co/Mg and SiC/Mg multilayer mirrors are as high as 40.3% and 44.6%, respectively, while those of B4C/Mg and Si/Mg mirrors are too low for application. The measured results suggest that SiC/Mg, Co/Mg multilayers are promising for a 30.4 nm wavelength.

41 CFR 304-6.1 - May we accept a monetary payment in the form of cash from a non-Federal source?

Science.gov (United States)

2010-07-01

... payment in the form of cash from a non-Federal source? 304-6.1 Section 304-6.1 Public Contracts and Property Management Federal Travel Regulation System PAYMENT OF TRAVEL EXPENSES FROM A NON-FEDERAL SOURCE... of cash from a non-Federal source? No, you may not accept a monetary payment in the form of cash from...

Improvement of life time of SCC in type 304 stainless steel by ultrasound irradiation

International Nuclear Information System (INIS)

Tokiwai, Moriyasu; Kimura, Hideo

1985-01-01

It is well known that the susceptibility to stress corrosion cracking (SCC) is controled by compressive stress such as shot-peening treatment. In this study, the effects of ultrasound irradiation to type 304 stainless upon SCC were investigated. The main findings are as follows; (1) Ultrasound irradiation produces the high level compressive stress on the surface of metals. This compressive stress was induced by the cavitation phenomenon. (2) In U-bent specimen, the initial tensile stress was mitigated and converted to compressive stress by ultrasound irradiation. (3) Type 304 stainless steel was subjected to SCC test using sodium thyosulfate solution. It was definitely demonstrated that the ultrasound irradiation was effective for the mitigation of SCC life time. (4) Ultrasound irradiation time was one of the most important factors in irradiation conditions. (author)

Conductivity and Structure of Superionic Composite (AgI0.6(NaPO30.4

Directory of Open Access Journals (Sweden)

E. Kartini

2005-01-01

Full Text Available Superionic conductors are of considerable interest from both application and fundamental points of view. Superionic solid electrolytes can be used for batteries, fuel cells and sensors. We have used melt quenching to make a new superionic composite (AgI0.6(NaPO30.4 which exhibits an ionic conductivity of about 2 x 10-4 S/cm at ambient temperature. The conductivity of crystalline AgI and NaPO3 glass are lower of orders of magnitude. (AgI0.6(NaPO30.4 is a composite material containing both crystalline and glass phases. The paper presents the conductivity as a function of temperature measured by impedance spectroscopy and the crystal structure performed by a high resolution powder diffractometer, VEGA at the Neutron Science Laboratory (KENS, KEK, Japan.

A three-dimensional thermal finite element analysis of AISI 304 stainless steel and copper dissimilar weldment

Science.gov (United States)

Singh, Gurdeep; Saxena, Ravindra K.; Pandey, Sunil

2018-04-01

The aim of this study to developed a 3-D thermal finite element model for dissimilar material welding of AISI-304 stainless steel and copper. Welding of similar material is widely studied using experimental and numerical methods but the problem becomes trivial for the welding of dissimilar materials especially in ferrous and nonferrous materials. Finite element analysis of dissimilar material welding is a cost-effective method for the understanding and analysis of the process. The finite element analysis has been performed to predict the heat affected zone and temperature distribution in AISI-304 stainless steel and copper dissimilar weldment using MSC Marc 2017®. Due to the difference in physical properties of these materials the behavior of heat affected zone and temperature distribution are perceived to be different. To verify the accuracy of the thermal finite element model, the welding process was simulated with butt-welded joints having same dimensions and parameters from Attarha and Far [1]. It is found from the study that the heat affected zone is larger in copper weld pads than in AISI 304 stainless steel due to large difference in thermal conductivity of these two weld pads.

Elevated temperature tensile properties of borated 304 stainless steel: Effect of boride dispersion on strength and ductility

International Nuclear Information System (INIS)

Stephens, J.J.; Sorenson, K.B.; McConnell, P.

1991-01-01

This paper has documented the increase in strain to fracture and yield strength obtained with Grade A versions of types 304B5 and 304B7 relative to their respective Grade B, counterparts. The apparent microstructural reason for these property increases is the finer dispersion of boride in the Grade A material, obtained by means of a Powder Metallurgy process, relative to the conventional Grade B material which is produced using an Ingot Metallurgy process. The area size distribution of borides can be well approximated using a log-normal distribution, with the largest boride particles in the Grade B material having areas in the range of 450--600 μm 2 . By comparison, the largest boride particles in the Grade A material have areas nearly an order of magnitude smaller than the largest particles in their Grade B counterparts. A Section III ASME B ampersand PV code case inquiry has been initiated for non-welded versions of 304B4A, 3045A and 3046A ,material

Biocompatibility of bismuth silicate coatings deposited on 316L stainless steel by sol-gel process

Directory of Open Access Journals (Sweden)

Jorge Hernando Bautista-Ruiz

2017-01-01

Full Text Available Películas delgadas de silicato de bismuto (BSO se han fabricado mediante el proceso sol-gel. El sol estable se sintetizó utilizando nitrato de bismuto (III pentahidrato y tetraetil-ortosilicato (TEOS. Las películas fueron depositadas a 1500 rpm mediante la técnica de centrifugado. Los recubrimientos se caracterizaron por microscopía de fuerza atómica (AFM, microscopía electrónica de barrido (SEM, difracción de rayos-X (DRX y se midió el espesor de las películas. El objetivo de este estudio fue evaluar la adhesión y la proliferación en células de osteoblastos, mediante el ensayo MMT, al incubarse sobre películas BSO en sustratos de 316L. Se concluyó que el crecimiento de los osteoblastos es homogéneo en la superficie de las películas, indicando que el medio ofrecido por los recubrimientos no presenta actividad citotóxica y favorece los niveles de crecimiento celular en comparación con los resultados obtenidos para los sustratos de acero inoxidable.

Wear resistance of AISI 304 stainless steel submitted to low temperature plasma carburizing

Directory of Open Access Journals (Sweden)

Marcos Antônio Barcelos

Full Text Available Abstract Despite the AISI 304 stainless steel has high corrosion/oxidation resistance, its tribological properties are poor, being one of the barriers for use in severe wear applications. Thus, there is a wide field for studying technologies that aim to increase the surface hardness and wear resistance of this material. In this work, hardness and wear resistance for AISI 304 stainless steel submitted to the thermochemical treatment by low temperature plasma carburizing (LTPC in a fixed gas mixture composition of 93% H2 and 7% CH4 are presented. Through the evaluation of the carburizing layers, it was possible to observe a substantial improvement in tribological properties after all temperature and time of treatment. This improvement is directly related to the increase of the process variables; among them temperature has a stronger influence on the wear resistance obtained using LTPC process.

Phase 1 sampling and analysis plan for the 304 Concretion Facility closure activities

International Nuclear Information System (INIS)

Adler, J.G.

1994-01-01

This document provides guidance for the initial (Phase 1) sampling and analysis activities associated with the proposed Resource Conservation and Recovery Act of 1976 (RCRA) clean closure of the 304 Concretion Facility. Over its service life, the 304 Concretion Facility housed the pilot plants associated with cladding uranium cores, was used to store engineering equipment and product chemicals, was used to treat low-level radioactive mixed waste, recyclable scrap uranium generated during nuclear fuel fabrication, and uranium-titanium alloy chips, and was used for the repackaging of spent halogenated solvents from the nuclear fuels manufacturing process. The strategy for clean closure of the 304 Concretion Facility is to decontaminate, sample (Phase 1 sampling), and evaluate results. If the evaluation indicates that a limited area requires additional decontamination for clean closure, the limited area will be decontaminated, resampled (Phase 2 sampling), and the result evaluated. If the evaluation indicates that the constituents of concern are below action levels, the facility will be clean closed. Or, if the evaluation indicates that the constituents of concern are present above action levels, the condition of the facility will be evaluated and appropriate action taken. There are a total of 37 sampling locations comprising 12 concrete core, 1 concrete chip, 9 soil, 11 wipe, and 4 asphalt core sampling locations. Analysis for inorganics and volatile organics will be performed on the concrete core and soil samples. Separate concrete core samples will be required for the inorganic and volatile organic analysis (VOA). Analysis for inorganics only will be performed on the concrete chip, wipe, and asphalt samples

Tailoring diffraction technique Rietveld method on residual stress measurements of cold-can oiled 304 stainless steel plates

International Nuclear Information System (INIS)

Parikin; Killen, P.; Anis, M.

2003-01-01

Tailoring of diffraction technique-Rietveld method on residual stress measurements of cold-canailed stainless steel 304 plates assuming the material is isotopic, the residual stress measurements using X-ray powder diffraction is just performed for a plane lying in a large angle. For anisotropic materials, the real measurements will not be represented by the methods. By Utilizing of all diffraction peaks in the observation region, tailoring diffraction technique-Rietveld analysis is able to cover the limitations. The residual stress measurement using X-ray powder diffraction tailored by Rietveld method, in a series of cold-canailed stainless steel 304 plates deforming; 0, 34, 84, 152, 158, 175, and 196 % reduction in thickness, have been reported. The diffraction data were analyzed by using Rietveld structure refinement method. Also, for all cold-canailed stainless steel 304 plates cuplikans, the diffraction peaks are broader than the uncanailed one, indicating that the strains in these cuplikans are inhomogeneous. From an analysis of the refined peak shape parameters, the average root-mean square strain, which describes the distribution of the inhomogeneous strain field, was calculated. Finally, the average residual stresses in cold-canailed stainless steel 304 plates were shown to be a combination effect of hydrostatic stresses of martensite particles and austenite matrix. The average residual stresses were evaluated from the experimentally determined average lattice strains in each phase. It was found the tensile residual stress in a cuplikan was maximum, reaching 442 MPa, for a cuplikan reducing 34% in thickness and minimum for a 196% cuplikan

20 CFR 703.304 - Filing of Agreement and Undertaking; deposit of security.

Science.gov (United States)

2010-04-01

... the amount fixed by the Office, or deposit negotiable securities under §§ 703.306 and 703.307 in that... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Filing of Agreement and Undertaking; deposit... REGULATIONS Authorization of Self-Insurers § 703.304 Filing of Agreement and Undertaking; deposit of security...

Correlation between evolution of inclusions and pitting corrosion in 304 stainless steel with yttrium addition.

Science.gov (United States)

Shi, Weining; Yang, Shufeng; Li, Jingshe

2018-03-19

Effects of the evolution of inclusions on the pitting corrosion resistance of 304 stainless steel with different contents of the rare-earth element yttrium (Y) were studied using thermodynamic calculations, accelerated immersion tests, and electrochemical measurements. The experimental results showed that regular Y 2 O 3 inclusions demonstrated the best pitting resistance, followed in sequence by (Al,Mn)O inclusions, the composite inclusions, and irregular Y 2 O 3 inclusions. The pitting resistance first decreased, then increased, and then decreased again with increasing Y content, because sulfide inclusions were easily generated when the Y content was low and YN inclusions were easily generated at higher Y contents. The best pitting corrosion resistance was obtained for 304 stainless steel with addition of 0.019% Y.

Spring back evaluation by bending under tension tests in conditions of multiaxial stresses corresponding to deep drawing processes. Application to AISI 304 DDQ stainless steel sheet; Evaluacion del springback mediante ensayos de doblado bajo tension en condiciones de multiaxialidad tipicas de los procesos de embuticion profunda. Aplicacion a chapa de acero inoxidable AISI 304 DDQ

Energy Technology Data Exchange (ETDEWEB)

Miguel, V.; Coello, J.; Martinez, A.; Calatayud, A.

2013-09-01

In this paper, a methodology has been developed for evaluating the spring back of AISI 304 DDQ stainless steel sheet based on a bending under tension test. The main difference of the methodology herein carried out is that tests are made under the multiaxial stresses state that take place in deep drawing processes. This affects to the level of stress value in the test and to the hardening state of the sheet. Springback evaluation has been done in two different areas. Bending area has been evaluated from elastic recovery ratio defined as the ratio between the bending radius after and before bending. Bending and unbending extreme has been studied from the measured curvature radius in this area and taking into account the geometric equivalence of the test with the drawing cups process. Results found allow to state that drawing ratio or deformation ratio have a negligible influence on the springback into the range of values experimented here. Bending radius has hardly influence as well while bending angle is the most significant variable. The results obtained are compared to those measured in deep-drawn cups, finding a great agreement. (Author)

Corrosion fatigue of AISI 304 stainless steel in aqueous chloride solution

International Nuclear Information System (INIS)

Ferrao, P.R.; Sousa e Silva, A.S. de; Castro, M.A.C. de

1982-01-01

The fatique behaviour of an 304 austenitic stainless steel in a 0,5 M NaCl environment was studied. The material was tested, under different electrode potential conditions and the results were compaired with those obtained for tests in air. It has been shown by means of metallographic and fractografic observations, that the mechanism of crack initiation depends on the applied potential. (Author) [pt

Co-overexpression of bacterial GroESL chaperonins partly overcomes non-productive folding and tetramer assembly of E. coli-expressed human medium-chain acyl-CoA dehydrogenase (MCAD) carrying the prevalent disease-causing K304E mutation

DEFF Research Database (Denmark)

Bross, P; Andresen, B S; Winter, V

1993-01-01

underlying MCAD deficiency caused by the prevalent K304E mutation. Depending on which of the three amino acids--lysine (wild-type), glutamic acid (K304E) or glutamine (K304Q) are present at position 304 of the mature polypeptide, three different patterns were observed in our assay system: (i) solubility...... in Western blotting. In a first attempt to estimate the specific activity, we show that tetrameric K304E and K304Q mutant MCAD display a specific activity in the range of the wild-type enzyme. Taken together, our results strongly suggest, that the K304E mutation primarily impairs the rate of folding...... with negative charge at position 304 (glutamic acid) but not with a neutral charge (glutamine) negatively affects conversion to active tetramers. A possible explanation for this latter effect--charge repulsion upon subunit docking--is discussed....

Evaluation of stress-corrosion cracking of sensitized 304SS in low-temperature borated water

International Nuclear Information System (INIS)

Jones, R.H.; Johnson, A.B. Jr.; Bruemmer, S.M.

1981-05-01

Intergranular stress corrosion cracking has been observed in constant extension rate tests, CERT and constant load tests of 304SS tested at 32 0 C in borated water plus 15 ppM C1 - . Evidence of IGSCC was obtained in CERT tests of welded pipe samples only when the original inner diameter surface was intact and with 15 ppM C1 - added to the borated water while IGSCC occurred in a furnace sensitized pipe sample after 500 h at a constant stress of 340 MPa in borated water containing 15 ppM C1 - . These results indicate that surface features associated with weld preparation grinding contributed to the susceptibility of sensitized 304SS to IGSCC in low temperature borated water; however, the constant load test indicates that such surface defects are not necessary for IGSCC in low temperature borated water

Study of the corrosion behaviors of 304 austenite stainless steel specimens exposed to static liquid lithium at 600 K

Energy Technology Data Exchange (ETDEWEB)

Meng, Xiancai [Department of Applied Physics, School of Physics and Electronics, Hunan University, Changsha 410082 (China); Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Zuo, Guizhong; Ren, Jun; Xu, Wei; Sun, Zhen; Huang, Ming [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Hu, Wangyu [Department of Applied Physics, School of Physics and Electronics, Hunan University, Changsha 410082 (China); Hu, Jiansheng, E-mail: hujs@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Deng, Huiqiu, E-mail: hqdeng@hnu.edu.cn [Department of Applied Physics, School of Physics and Electronics, Hunan University, Changsha 410082 (China)

2016-11-15

Investigation of corrosion behavior of stainless steel served as one kind of structure materials exposed to liquid lithium (Li) is one of the keys to apply liquid Li as potential plasma facing materials (PFM) or blanket coolant in the fusion device. Corrosion experiments of 304 austenite stainless steel (304 SS) were carried out in static liquid Li at 600 K and up to1584 h at high vacuum with pressure less than 4 × 10{sup −4} Pa. After exposure to liquid Li, it was found that the weight of 304 SS slightly decreased with weight loss rate of 5.7 × 10{sup −4} g/m{sup 2}/h and surface hardness increased by about 50 HV. Lots of spinel-like grains and holes were observed on the surface of specimens measured by SEM. By further EDS, XRD and metallographic analyzing, it was confirmed that the main compositions of spinel-like grains were M{sub 23}C{sub 6} carbides, and 304 SS produced a non-uniform corrosion behavior by preferential grain boundary attack, possibly due to the easy formation of M{sub 23}C{sub 6} carbides and/or formation of Li compound at grain boundaries.

On the grain boundary hardening in a B-bearing 304 austenitic stainless steel

International Nuclear Information System (INIS)

Yao, X.X.

1999-01-01

The precipitates, (Cr,Fe) 23 (C,B) 6 carbides and (Cr,Fe) 2 B borides, formed along the grain boundaries in a 304 austenitic stainless steel containing boron of 33 ppm after solution treatment at 1100 C for 1 h followed by isothermal ageing for 0.5 h at temperatures ranging from 750 to 1050 C have been identified. The influence of these precipitates on the grain boundary hardening has been investigated by means of micro-Vickers hardness measurements. It is found that the degree of grain boundary hardening below 900 C decreases, while it increases above 900 C with increasing ageing temperature. The dissolution of (Cr,Fe) 23 (C,B) 6 carbides and the precipitation of (Cr,Fe) 2 B borides are associated with the changes of grain boundary hardening in this B-bearing 304 austenitic stainless steel between 750 and 1100 C. The non-equilibrium boron segregation enhances the grain boundary hardening when the ageing temperature is above 900 C. (orig.)