WorldWideScience

Sample records for inorganic polymeric binder

  1. Heat-resistant inorganic binders.

    Directory of Open Access Journals (Sweden)

    KUDRYAVTSEV Pavel Gennadievich,

    2017-04-01

    Full Text Available The authors consider some aspects of production of inorganic heat-resistant composite materials in which new classes of inorganic binders - the basic salts of various metals – are applied. The possibility to use hydroxochlorides and hydroxonitrates of aluminum, zirconium, chromium and a number of other metals as the binder has been shown. The main products of the thermal decomposition of all types of binders discussed in this paper are nano-dispersed highly refractory oxides. Increased pressure in the manufacture of these materials shifts the position of the minimum of the dependence «production strength – production temperature» in the direction of low temperatures. This effect is caused by decreased film thickness of the binder located between filler particles and hence by increased rate of transfer of the matter to the interface and by facilitated sintering process. Materials based on the systems containing chromium and some other elements in transitional oxidation states are colour. For this reason, they have the worst thermal conductivity under the same heat resistance compared to colorless materials.

  2. Studies on the Renewability of Polymeric Binders for Foundry

    Directory of Open Access Journals (Sweden)

    B. Grabowska

    2012-09-01

    Full Text Available In this paper the results of studies of polymeric binders on the example of the new BioCo2 binder, including the problem of itsrenewability, are presented. The results of structural studies (FT-IR for the BioCo2 binder before and after crosslinking, and bendingstrength tests Rg u fresh and renewed cured molding sands with BioCo2 binder are discussed. The cross-linking binder and curring ofmoulding sand was carried out by physical agents (microwave radiation, temperature. On the basis of obtained results was shown that it is possible to restore the initial properties of the adhesive of BioCo2 binder. The initial properties of moulding sand can be achieved, after the cross-linking binders and after curing in the moulding sands with bioCo2 binder , by supplementing the moulding sand composition by the appropriate amount of water.

  3. THE STUDY OF CORE SAND MIXTURES BASED ON POLYMERIC BINDERS

    Directory of Open Access Journals (Sweden)

    Ms. Natalia V. Zakharova

    2016-06-01

    Full Text Available The possibility of using foamed polystyrene waste as the binder in manufacturing core sand mixtures. The article provides experimental data obtained by studying the core sand mixtures properties depending on the methods of addition, foamed polystyrene solution amount, its viscosity and the method of drying. The author investigates the ways of using foamed polystyrene as the binder and as the polymeric additive.

  4. Evaluation of Reclamability of Molding Sands with New Inorganic Binders

    Directory of Open Access Journals (Sweden)

    I. Izdebska-Szanda

    2012-04-01

    Full Text Available One of the purposes of the application of chemically modified inorganic binders is to improve knocking out properties and the related reclamability with previously used in foundry inorganic binder (water glass, which allowing the use of ecological binders for casting non- ferrous metals. Good knocking out properties of the sands is directly related to the waste sands reclamability, which is a necessary condition of effective waste management. Reclamation of moulding and core sands is a fundamental and effective way to manage waste on site at the foundry, in accordance with the Environmental Guidelines. Therefore, studies of reclamation of waste moulding and core sands with new types of inorganic binders (developed within the framework of the project were carried out. These studies allowed to determine the degree of recovery of useful, material, what the reclaimed sand is, and the degree of its use in the production process. The article presents these results of investigation. They are a part of broader research programme executed under the project POIG.01.01.02-00- 015/09 "Advanced materials and technologies".

  5. Novel, inorganic composites using porous, alkali-activated, aluminosilicate binders

    Science.gov (United States)

    Musil, Sean

    Geopolymers are an inorganic polymeric material composed of alumina, silica, and alkali metal oxides. Geopolymers are chemical and fire resistant, can be used as refractory adhesives, and are processed at or near ambient temperature. These properties make geopolymer an attractive choice as a matrix material for elevated temperature composites. This body of research investigated numerous different reinforcement possibilities and variants of geopolymer matrix material and characterized their mechanical performance in tension, flexure and flexural creep. Reinforcements can then be chosen based on the resulting properties to tailor the geopolymer matrix composites to a specific application condition. Geopolymer matrix composites combine the ease of processing of polymer matrix composites with the high temperature capability of ceramic matrix composites. This study incorporated particulate, unidirectional fiber and woven fiber reinforcements. Sodium, potassium, and cesium based geopolymer matrices were evaluated with cesium based geopolymer showing great promise as a high temperature matrix material. It showed the best strength retention at elevated temperature, as well as a very low coefficient of thermal expansion when crystallized into pollucite. These qualities made cesium geopolymer the best choice for creep resistant applications. Cesium geopolymer binders were combined with unidirectional continuous polycrystalline mullite fibers (Nextel(TM) 720) and single crystal mullite fibers, then the matrix was crystallized to form cubic pollucite. Single crystal mullite fibers were obtained by the internal crystallization method and show excellent creep resistance up to 1400°C. High temperature flexural strength and flexural creep resistance of pollucite and polycrystalline/single-crystal fibers was evaluated at 1000-1400°C.

  6. Preparation, Properties and Application of Polymeric Organic-Inorganic Nanocomposites

    Institute of Scientific and Technical Information of China (English)

    任杰; 刘艳; 唐小真

    2003-01-01

    Six preparation methods for polymeric organic-inorganic nanocomposites and their respective mechanisms and features are reviewed. The extraordinary properties of polymeric organic-inorganic nanocomposites are discussed,and their potential applications are evaluated.

  7. Conductive Polymeric Binder for Lithium-Ion Battery Anode

    Science.gov (United States)

    Gao, Tianxiang

    Tin (Sn) has a high-specific capacity (993 mAhg-1) as an anode material for Li-ion batteries. To overcome the poor cycling performance issue caused by its large volume expansion and pulverization during the charging and discharging process, many researchers put efforts into it. Most of the strategies are through nanostructured material design and introducing conductive polymer binders that serve as matrix of the active material in anode. This thesis aims for developing a novel method for preparing the anode to improve the capacity retention rate. This would require the anode to have high electrical conductivity, high ionic conductivity, and good mechanical properties, especially elasticity. Here the incorporation of a conducting polymer and a conductive hydrogel in Sn-based anodes using a one-step electrochemical deposition via a 3-electrode cell method is reported: the Sn particles and conductive component can be electrochemically synthesized and simultaneously deposited into a hybrid thin film onto the working electrode directly forming the anode. A well-defined three dimensional network structure consisting of Sn nanoparticles coated by conducting polymers is achieved. Such a conductive polymer-hydrogel network has multiple advantageous features: meshporous polymeric structure can offer the pathway for lithium ion transfer between the anode and electrolyte; the continuous electrically conductive polypyrrole network, with the electrostatic interaction with elastic, porous hydrogel, poly (2-acrylamido-2-methyl-1-propanesulfonic acid-co-acrylonitrile) (PAMPS) as both the crosslinker and doping anion for polypyrrole (PPy) can decrease the volume expansion by creating porous scaffold and softening the system itself. Furthermore, by increasing the amount of PAMPS and creating an interval can improve the cycling performance, resulting in improved capacity retention about 80% after 20 cycles, compared with only 54% of that of the control sample without PAMPS. The cycle

  8. Viscoelastic Behaviour of Solid Propellants based on Various Polymeric Binders

    Directory of Open Access Journals (Sweden)

    N. Prabhakaran

    1995-01-01

    Full Text Available The dynamic mechanical properties of different binders and corresponding propellants are studied in terms of storage modulus and loss tangent. The binders investigated are HTPB, CTPB, PBAN, HEF-20 and ISRO polyol. The viscoelastic behaviour is investigated using Rheovibron viscoelastometer at 35 Hz covering a wide temperature range (-100 degree centigrade to 100 degree centigrade. The properties of the binder and corresponding propellant are compared in terms of parameters, tan delta/sub max/, T/sub g/ and the trend of their master relaxation modulus curves. It is found that polybutadiene binders exhibit lowest T/sub g/ (around -60 degree centigrade and ISRO polyol the highest (near -20 degree centigrade. The propellants have higher moduli than the binders at any temperature. The master relaxation modulus curve is influenced by the type of propellant.

  9. Inorganic Surface Modification of Nonwoven Polymeric Substrates

    Science.gov (United States)

    Halbur, Jonathan Chandler

    In this study, atomic layer deposition (ALD), a vapor phase inorganic thin film deposition technique, is used to modify the surface of a range of industrially relevant polymers to enhance surface properties or impart additional functionalities. Several unique demonstrations of polymer surface modification are presented including uniform nanomaterial photodeposition to the surface of nonowoven fabrics and the first application of photocatalytic thin film coated nonwovens for advanced filtration of heavy metals from solution. Recent advances in polymer synthesis and processing technologies have resulted in the production of novel polymer systems with unique chemistries and sub-micron scale dimensions. As a result, advanced fiber systems have received much attention for potential use in a wide range of industrially and medically important applications such as advanced and selective filtration, catalysis, flexible electronics, and tissue engineering. However, tailoring the surface properties of the polymer is still needed in order to realize the full range of advanced applications, which can be difficult given the high complexity and non-uniformity of nonwoven polymeric structures. Uniform and controllable inorganic surface modification of nonwovens allows the introduction or modification of many crucial polymer properties with a wide range of application methods.

  10. Partition of biocides between water and inorganic phases of renders with organic binder

    DEFF Research Database (Denmark)

    Urbanczyk, Michal M; Bollmann, Ulla E; Bester, Kai

    2016-01-01

    , the partition of biocides between water and inorganic phases of render with organic binder was investigated. The partition constants of carbendazim, diuron, iodocarb, isoproturon, cybutryn (irgarol), octylisothiazolinone, terbutryn, and tebuconazole towards minerals typically used in renders, e.g. barite...... with render-water distribution constants of two artificially made renders showed that the distribution constants can be estimated based on partition constants of compounds for individual components of the render....

  11. Binder-Free and Carbon-Free Nanoparticle Batteries: A Method for Nanoparticle Electrodes without Polymeric Binders or Carbon Black

    KAUST Repository

    Ha, Don-Hyung

    2012-10-10

    In this work, we have developed a new fabrication method for nanoparticle (NP) assemblies for Li-ion battery electrodes that require no additional support or conductive materials such as polymeric binders or carbon black. By eliminating these additives, we are able to improve the battery capacity/weight ratio. The NP film is formed by using electrophoretic deposition (EPD) of colloidally synthesized, monodisperse cobalt NPs that are transformed through the nanoscale Kirkendall effect into hollow Co 3O 4. EPD forms a network of NPs that are mechanically very robust and electrically connected, enabling them to act as the Li-ion battery anode. The morphology change through cycles indicates stable 5-10 nm NPs form after the first lithiation remained throughout the cycling process. This NP-film battery made without binders and conductive additives shows high gravimetric (>830 mAh/g) and volumetric capacities (>2100 mAh/cm 3) even after 50 cycles. Because similar films made from drop-casting do not perform well under equal conditions, EPD is seen as the critical step to create good contacts between the particles and electrodes resulting in this significant improvement in battery electrode assembly. This is a promising system for colloidal nanoparticles and a template for investigating the mechanism of lithiation and delithiation of NPs. © 2012 American Chemical Society.

  12. Technological and ecological studies of moulding sands with new inorganic binders for casting of non-ferrous metal alloys

    Directory of Open Access Journals (Sweden)

    I. Izdebska-Szanda

    2011-01-01

    Full Text Available The article presents the results of studies which form a part of broader research programme executed under the project POIG.01.01.02-00-015/09 "Advanced materials and technologies".In a concise manner, the results of studies on the effect of chemical modification of inorganic binders on the technological properties ofmoulding sands containing these binders were presented.Special attention was paid to the effect of modification of inorganic binders on their thermal destruction behaviour in the range of pouringtemperatures of the non-ferrous metals and their alloys.Also the results of comparative studies of the thermal emission of toxic gases and odours from moulding sands with new inorganic andorganic binders were discussed.

  13. Production of Steel Casts in Two-Layer Moulds with Alkaline Binders Part 1. Backing sand with the alkaline inorganic binder RUDAL

    Directory of Open Access Journals (Sweden)

    M. Holtzer

    2011-04-01

    Full Text Available Steel casts in Z.N. POMET were produced in moulds made of the moulding sand Floster. This sand did not have good knocking outproperties, required a significant binder addition (4.5-5.0 parts by weight, and the casting surface quality gave rise to clients objections.Therefore a decision of implementing two-layer moulds, in which the facing sand would consist of the moulding sand with an alkalineorganic binder while the backing sand would be made of the moulding sand with an inorganic binder also of an alkaline character - wasundertaken. The fraction of this last binder in the moulding sand mass would be smaller than that of the binder used up to now (waterglass. The application of two moulding sands of the same chemical character (highly alkaline should facilitate the reclamation processand improve the obtained reclaimed material quality, due to which it would be possible to increase the reclaim fraction in the mouldingsand (up to now it was 50%. The results of the laboratory investigations of sands with the RUDAL binder are presented in the paper.

  14. Production of inorganic pellet binders from fly-ash. Technical report, March 1--May 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Kawatra, S.K.; Eisele, T.C.

    1995-12-31

    Fly-ash is produced by all coal-fired utilities, and it must be removed from the plant exhaust gases, collected, and disposed of. While much work has been done in the past to utilize fly-ash rather than disposing of it, we nevertheless do not find widespread examples of successful industrial utilization. This is because past work has tended to find uses only for high-quality, easily-utilized fly-ashes, which account for less than 25% of the fly-ash that is produced. The main factor which makes fly-ashes unusable is a high unburned carbon content. In this project, physical separation technologies are being used to remove this carbon, and to convert these unusable fly-ashes into usable products. The main application being studied for the processed fly-ash is as a binder for inorganic materials, such as iron-ore pellets. In the second quarter, additional fly-ash samples were collected from the E. D. Edwards station (Bartonville, IL). Experimentation was begun to study the removal of carbon from these fly-ashes by froth flotation, and make and test pellets that use fly-ash as binder. During the current quarter, flotation experiments were continued on the fly- ashes. Three types of ashes were studied: 1. Ash from the disposal pond (``wet`` ash); 2. Dry fly-ash collected directly from the standard burners (``low-carbon`` ash); 3. Dry fly-ash collected from the low-NOx burners (``high-carbon`` ash). Each of these was chemically analyzed, and conventional flotation experiments were carried out to determine the optimum reagent dosages for carbon removal. Decarbonized ashes were then made from each ash type, in sufficient quantity to be used in pelletization experiments.

  15. Organic/Inorganic Polymeric Composites for Heat-Transfer Reduction

    Science.gov (United States)

    Smith, Trent; Williams, Martha

    2008-01-01

    Organic/inorganic polymeric composite materials have been invented with significant reduction in heat-transfer properties. Measured decreases of 20-50 percent in thermal conductivity versus that of the unmodified polymer matrix have been attained. These novel composite materials also maintain mechanical properties of the unmodified polymer matrix. The present embodiments are applicable, but not limited to: racing applications, aerospace applications, textile industry, electronic applications, military hardware improvements, and even food service industries. One specific application of the polymeric composition is for use in tanks, pipes, valves, structural supports, and components for hot or cold fluid process systems where heat flow through materials is problematic and not desired. With respect to thermal conductivity and physical properties, these materials are superior alternatives to prior composite materials. These materials may prove useful as substitutes for metals in some cryogenic applications. A material of this type can be made from a blend of thermoplastics, elastomers, and appropriate additives and processed on normal polymer processing equipment. The resulting processed organic/inorganic composite can be made into fibers, molded, or otherwise processed into useable articles.

  16. Comparative assessment of water treatment using polymeric and inorganic coagulants

    Science.gov (United States)

    Manda, Innocent K. M.; Chidya, Russel C. G.; Saka, John D. K.; Biswick, Timothy T.

    2016-06-01

    Portable water plays a vital role in improving human life, particularly in controlling the spread of diseases. However, problems associated with lack of potable water are still common especially in developing countries including Malawi. Until now little information exists on the effectiveness of available commercial coagulants used by national water boards in Malawi. Therefore, this study was undertaken in Southern Region Water Board (SRWB) to investigate the efficiency of polymeric coagulants (sufdfloc 3850 and algaefloc 19s) in turbidity reduction comparative with inorganic coagulant (aluminium sulphate) at Zomba, Liwonde, Mangochi, Chikwawa and Mulanje Treatment plants. The jar test method was used to determine the effectiveness of the water coagulants. The results revealed that sudfloc 3850 was most effective in reducing turbidity at Mangochi (99.4 ± 0.06%) and Liwonde (97.2 ± 0.04%) using 0.4 mg L-1 flocculant dose. The Zomba, Mulanje and Chikwawa plants gave 19.56 ± 0.03%, 29.23 ± 0.02% and 9.43 ± 0.02% total reductions respectively. Algaefloc 19s afforded the highest turbidity reduction at Liwonde and Mangochi plants (98.66 ± 0.06 and 97.48 ± 0.05% at a dose of 0.4 and 0.6 mg L-1 respectively), while Chikwawa provided the lowest (9.52 ± 0.01%). At the Zomba and Mulanje plants 20.5 ± 0.03% and 28.4 ± 0.04% reductions were obtained respectively. The inorganic flocculant, alum provided a 99.0 ± 0.05% and 98.6 ± 0.04% reduction at a dose of 4.0 mg L-1 and 6.0 mg L-1 at Zomba and Liwonde plants respectively. The lowest reductions in turbidity were achieved at Chikwawa (7.50 ± 0.01%), Mangochi (12.97 ± 0.02%) and Mulanje (25.00 ± 0.02). The best and optimum pH ranges for polymeric and inorganic coagulants were 7.20-7.80 and 7.35 to 7.57 respectively. The results further revealed that sudfloc 3850 and algaefloc 19s achieved faster formation of heavy flocs than alum. At 0.4 mg L-1 flocculant dosage sudfloc 3850 and algaefloc 19s required ten times

  17. Influence of wet activation of used inorganic binder on cyclically refreshed water glass moulding sands hardened by microwaves

    OpenAIRE

    Mateusz Stachowicz; Kazimierz Granat

    2016-01-01

    The paper presents the research results of using an innovative method to reclaim the waste moulding sands containing water glass. Two of the examined processes are connected with "dry" or "wet" activation of inorganic binder in waste moulding sand mixtures physically hardened by microwave radiation. The sand mixtures consisting of high-silica sand and water-glass with average molar module 2.5, were subjected to the following cyclical process: mixing the components, compacting, microwave heati...

  18. Development of foamed Inorganic Polymeric Materials based on Perlite

    Science.gov (United States)

    Tsaousi, G.-M.; Douni, I.; Taxiarchou, M.; Panias, D.; Paspaliaris, I.

    2016-04-01

    This work deals with the development of lightweight geopolymeric boards for use in construction sector utilizing a solid perlitic waste as the main raw material. Hydrogen peroxide (H2O2) was used for the foaming of geopolymeric pastes and the production of porous and lightweight inorganic polymeric materials. The effect of geopolymeric synthesis parameters, such as the composition of activator and the curing conditions, on paste's properties that affect the foaming process, such as setting time and viscosity, were studied in detailed. Finally, the effects of H2O2 concentration on the properties (apparent density and % cell volume) and the microstructure of foamed boards were also studied. The produced porous boards have effective densities in-between 540 - 900 Kg/m3 and the thermal conductivity of the optimum product is 0.08 W/mK. Based on their properties, the developed lightweight geopolymeric boards have high potential to be used as building elements in construction industry.

  19. The influence of metakaolin substitution by slag in alkali-activated inorganic binders for civil engineering

    Science.gov (United States)

    Kadlec, J.; Rieger, D.; Kovářík, T.; Novotný, P.; Franče, P.; Pola, M.

    2017-02-01

    In this study the effect of metakaolin replacement by milled blast furnace slag in alkali-activated geopolymeric binder was investigated in accordance to their rheological and mechanical properties. It was demonstrated that slag addition into the metakaolin binder can improve mechanical properties of final products. Our investigation was focused on broad interval of metakaolin substitution in the range from 100 to 40 volume per cents of metakaolin so that the volume content of solids in final binder was maintained constant. Prepared binders were activated by alkaline solution of potassium silicate with silicate module of 1.61. The particle size analyses were performed for determination of particle size distribution. The rheological properties were determined in accordance to flow properties by measurements on Ford viscosity cup and by oscillatory measurements of hardening process. For the investigation of hardening process, the strain controlled small amplitude oscillatory rheometry was used in plane-plate geometry. For determination of applied mechanical properties were binders filled by ceramic grog in the granularity range 0-1 mm. The filling was maintained constant at 275 volume per cents in accordance to ratio of solids in dry binder. The mechanical properties were investigated after 1, 7 and 28 days and microstructure was documented by scanning electron microscopy. The results indicate that slag addition have beneficial effect not only on mechanical properties of hardened binder but also on flow properties of fresh geopolymer paste and subsequent hardening kinetics of alkali-activated binders.

  20. Influence of wet activation of used inorganic binder on cyclically refreshed water glass moulding sands hardened by microwaves

    Directory of Open Access Journals (Sweden)

    Mateusz Stachowicz

    2016-11-01

    Full Text Available The paper presents the research results of using an innovative method to reclaim the waste moulding sands containing water glass. Two of the examined processes are connected with "dry" or "wet" activation of inorganic binder in waste moulding sand mixtures physically hardened by microwave radiation. The sand mixtures consisting of high-silica sand and water-glass with average molar module 2.5, were subjected to the following cyclical process: mixing the components, compacting, microwave heating, cooling-down, thermally loading the mould to 800 °C, cooling-down to ambient temperature, and knocking-out. After being knocked-out, the waste moulding sands were subjected to either dry or wet activation of the binder. To activate thermally treated inorganic binder, each of the examined processes employed the surface phenomenon usually associated to mechanical reclamation. The study also covered possible use of some elements of wet reclamation to rehydrate waste binder. To evaluate the effectiveness of the two proposed methods of waste binder activation, selected strength and technological parameters were measured. After each subsequent processing cycle, the permeability, tensile strength and bending strength were determined. In addition, the surface of activated sand grains was examined with a scanning electron microscope. Analysis of the results indicates that it is possible to re-activate the used binder such as sodium silicate, and to stabilize the strength parameters in both activation processes. Permeability of the refreshed moulding sands strongly depends on the surface condition of high-silica grains. The wet activation process by wetting and buffering knocked-out moulding sands in closed humid environment makes it possible to reduce the content of refreshing additive in water-glass. The moulding sands cyclically prepared in both processes do not require the addition of fresh high-silica sand. The relatively high quality achieved in the

  1. Investigating the Use of Polymeric Binders in Twin Screw Melt Granulation Process for Improving Compactibility of Drugs.

    Science.gov (United States)

    Batra, Amol; Desai, Dipen; Serajuddin, Abu T M

    2017-01-01

    Traditionally, the melt granulation for pharmaceutical products was performed at low temperature (twin screw extruder where the processing temperature could be increased to as high as 180°C and polymers with high Tg could be used as binders. In this study, different polymeric binders were screened for their suitability in improving compactibility of 2 drugs, metformin hydrochloride and acetaminophen, by twin screw melt granulation. Processing temperatures for the 2 drugs were set at 180°C and 130°C, respectively. Screw configuration, screw speed, and feed rate were optimized such that all polymeric binders used produced granules. Several hydroxypropyl cellulose, hydroxypropyl methylcellulose, polyvinylpyrrolidone, and methacrylate-based polymers, including Klucel(®) EXF, Eudragit(®) EPO, and Soluplus(®), demonstrated good tablet tensile strength (>2 MPa) when granules were produced using only 10% wt/wt polymer concentration. Certain polymers provided acceptable compactibility even at 5% wt/wt. Thus, twin screw melt granulation process may be used with different polymers at a wide range of temperature. Due to low excipient concentration, this granulation method is especially suitable for high-dose tablets.

  2. Production of inorganic pellet binders from fly-ash. Quarterly report, 1 December 1994--28 February 1995

    Energy Technology Data Exchange (ETDEWEB)

    Kawatra, S.K.; Eisele, T.C.

    1995-12-31

    Fly-ash is produced by all coal-fired utilities, and it must be removed from the plant exhaust gases, collected, and disposed of. While much work has been done in the past to utilize fly-ash rather than disposing of it, we nevertheless do not find widespread examples of successful industrial utilization. This is because past work has tended to find uses only for high-quality, easily-utilized fly-ashes, which account for less than 25% of the fly-ash that is produced. The main factor which makes fly-ashes unusable is a high unburned carbon content. In this project, physical separation technologies are being used to remove this carbon, and to convert these unusable fly-ashes into usable products. The main application being studied for the processed fly-ash is as a binder for inorganic materials, such as iron-ore pellets. Work in the first quarter concentrated on obtaining samples of all of the materials to be used (fly-ash, and magnetite ore), training of personnel on pelletization procedures, obtaining and setting up pelletization apparatus in the MTU laboratories, and running pelletization experiments with bentonite binder to establish a baseline for comparison with the fly-ash binders to be made.

  3. Study on an Improved Phosphate Cement Binder for the Development of Fiber-Reinforced Inorganic Polymer Composites

    Directory of Open Access Journals (Sweden)

    Zhu Ding

    2014-11-01

    Full Text Available Magnesium phosphate cement (MPC has been proven to be a very good repair material for deteriorated concrete structures. It has excellent adhesion performance, leading to high bonding strength with old concrete substrates. This paper presents an experimental study into the properties of MPC binder as the matrix of carbon fiber sheets to form fiber-reinforced inorganic polymer (FRIP composites. The physical and mechanical performance of the fresh mixed and the hardened MPC paste, the bond strength of carbon fiber sheets in the MPC matrix, the tensile strength of the carbon FRIP composites and the microstructure of the MPC matrix and fiber-reinforced MPC composites were investigated. The test results showed that the improved MPC binder is well suited for developing FRIP composites, which can be a promising alternative to externally-bonded fiber-reinforced polymer (FRP composites for the strengthening of concrete structures. Through the present study, an in-depth understanding of the behavior of fiber-reinforced inorganic MPC composites has been achieved.

  4. Multispectroscopic and Isotopic Ratio Analysis To Characterize the Inorganic Binder Used on Pompeian Pink and Purple Lake Pigments.

    Science.gov (United States)

    Marcaida, Iker; Maguregui, Maite; Morillas, Héctor; García-Florentino, Cristina; Knuutinen, Ulla; Carrero, Jose Antonio; Fdez-Ortiz de Vallejuelo, Silvia; Pitarch Martı́, Africa; Castro, Kepa; Madariaga, Juan Manuel

    2016-06-21

    Because of the fact that pigments are not ubiquitous in the archeological record, the application of noninvasive analytical methods is a necessity. In this work, pink and purple lake pigments recovered from the excavations of the ancient city of Pompeii (Campania, Italy) and preserved in their original bowls at the Naples National Archaeological Museum (Italy) were analyzed to characterize the composition of their inorganic binders (mordants). In situ preliminary analyses using a hand-held energy dispersive X-ray fluorescence spectrometer (HH-ED-XRF) allowed us to determine the use of an aluminosilicate enriched in Cu and Pb. Scanning electron microscopy coupled to energy dispersive X-ray spectrometry (SEM-EDS) and benchtop ED-XRF analyses confirmed these results, while inductively coupled plasma mass spectrometry (ICPMS) allowed one to determine the concentration of major, minor, and trace elements. The use of other techniques such as X-ray diffraction (XRD), and micro-Raman and infrared spectroscopies allowed one to characterize the pigments at the molecular level. The high concentration of Cu detected in the pigments (1228-12937 μg g(-1)) could be related to the addition of Cu salts to obtain the desired final hue. The concentrations of Pb (987-2083 μg g(-1)) was also remarkable. Lead isotopic ratio analysis ((206)Pb/(207)Pb) suggested a possible origin related to the leaching of the ancient lead pipes from Pompeii and the subsequent transfer to the buried pigments or to the inorganic binder. Molecular analysis also showed that the binder is composed of an allophane-like clay. Moreover, it was possible to determine that to obtain the final purple hue of a specific pigment, Pompeian blue pigment was also mixed into the dyed clay.

  5. Advanced Polymeric and Organic–Inorganic Membranes for Pressure-Driven Processes

    KAUST Repository

    Le, Ngoc Lieu

    2017-02-13

    The state-of-the-art of membranes for reverse osmosis, nanofiltration, and gas separation is shortly reviewed, taking in account the most representative examples currently in application. Emphasis is also done on recent developments of advanced polymeric and organic–inorganic materials for pressure-driven processes. Many of the more recent membranes are not only polymeric but also contain an inorganic phase. Tailoring innovative materials with organic and inorganic phases coexisting in a nanoscale with multifunctionalization is an appealing approach to control at the same time diffusivity and gas solubility. Other advanced materials that are now being considered for membrane development are organic or organic–inorganic self-assemblies, metal-organic frameworks, and different forms of carbon fillers.

  6. Biomedical inorganic polymers bioactivity and applications of natural and synthetic polymeric inorganic molecules

    CERN Document Server

    Müller, Werner E G; Schröder, Heinz C; Schroder, Heinz C

    2014-01-01

    In recent years, inorganic polymers have attracted much attention in nano-biomedicine, in particular in the area of regenerative medicine and drug delivery. This growing interest in inorganic polymers has been further accelerated by the development of new synthetic and analytical methods in the field of nanotechnology and nanochemistry. Examples for biomedical inorganic polymers that had been proven to exhibit biomedical effects and/or have been applied in preclinical or clinical trials are polysilicate / silica glass (such as naturally formed "biosilica" and synthetic "bioglass") and inorganic polyphosphate. Some members of the mentioned biomedical inorganic polymers have already been applied e.g. as "bioglass" for bone repair and bone tissue engineering, or they are used in food processing and in dental care (inorganic polyphosphates). However, there are a number of further biological and medicinal properties of these polymers, which have been elucidated in the last few years but not yet been applied for tr...

  7. Highly robust silicon nanowire/graphene core-shell electrodes without polymeric binders

    Science.gov (United States)

    Lee, Sang Eon; Kim, Han-Jung; Kim, Hwanjin; Park, Jong Hyeok; Choi, Dae-Geun

    2013-09-01

    A large theoretical charge storage capacity along with a low discharge working potential renders silicon a promising anode material for high energy density lithium ion batteries. However, up to 400% volume expansion during charge-discharge cycling coupled with a low intrinsic electronic conductivity causes pulverization and fracture, thus inhibiting silicon's widespread use in practical applications. We report herein on a low cost approach to fabricate hybrid silicon nanowire (SiNW)/graphene nanostructures that exhibit enhanced cycle performance with the capability of retaining more than 90% of their initial capacity after 50 cycles. We also demonstrate the use of hot-pressing in the absence of any common polymer binder such as PVDF to bind the hybrid structure to the current collector. The applied heat and pressure ensure strong adhesion between the SiNW/graphene nano-composite and current collector. This facile yet strong binding method is expected to find use in the further development of polymer-binder free anodes for lithium ion batteries.A large theoretical charge storage capacity along with a low discharge working potential renders silicon a promising anode material for high energy density lithium ion batteries. However, up to 400% volume expansion during charge-discharge cycling coupled with a low intrinsic electronic conductivity causes pulverization and fracture, thus inhibiting silicon's widespread use in practical applications. We report herein on a low cost approach to fabricate hybrid silicon nanowire (SiNW)/graphene nanostructures that exhibit enhanced cycle performance with the capability of retaining more than 90% of their initial capacity after 50 cycles. We also demonstrate the use of hot-pressing in the absence of any common polymer binder such as PVDF to bind the hybrid structure to the current collector. The applied heat and pressure ensure strong adhesion between the SiNW/graphene nano-composite and current collector. This facile yet strong

  8. Modulating semiconductor surface electronic properties by inorganic peptide-binders sequence design.

    Science.gov (United States)

    Matmor, Maayan; Ashkenasy, Nurit

    2012-12-19

    The use of proteins and peptides as part of biosensors and electronic devices has been the focus of intense research in recent years. However, despite the fact that the interface between the bioorganic molecules and the inorganic matter plays a significant role in determining the properties of such devices, information on the electronic properties of such interfaces is sparse. In this work, we demonstrate that the identity and position of single amino acid in short inorganic binding protein-segments can significantly modulate the electronic properties of semiconductor surfaces on which they are bound. Specifically, we show that the introduction of tyrosine or tryptophan, both possessing an aromatic side chain which higher occupied molecular orbitals are positioned in proximity to the edge of GaAs valence band, to the sequence of a peptide that binds to GaAs (100) results in changes of both the electron affinity and surface potential of the semiconductor. These effects were found to be more pronounced than the effects induced by the same amino acids once bound on the surface in a head-tail configuration. Furthermore, the relative magnitude of each effect was found to depend on the position of the modification in the sequence. This sequence dependent behavior is induced both indirectly by changes in the peptide surface coverage, and directly, probably, due to changes in the orientation and proximity of the tyrosine/tryptophan side group with respect to the surface due to the preferred conformation the peptide adopts on the surface. These studies reveal that despite the use of short protein oligomers and aiming at a non-natural-electronic task, the well-known relations between the proteins' structure and function is preserved. Combining the ability to tune the electronic properties at the interface with the ability to direct the growth of inorganic materials makes peptides promising building blocks for the construction of novel hybrid electronic devices and biosensors.

  9. High-Voltage Insulation Organic-Inorganic Nanocomposites by Plasma Polymerization

    Directory of Open Access Journals (Sweden)

    Wei Yan

    2014-01-01

    Full Text Available In organic-inorganic nanocomposites, interfacial regions are primarily influenced by the dispersion uniformity of nanoparticles and the strength of interfacial bonds between the nanoparticles and the polymer matrix. The insulating performance of organic-inorganic dielectric nanocomposites is highly influenced by the characteristics of interfacial regions. In this study, we prepare polyethylene oxide (PEO-like functional layers on silica nanoparticles through plasma polymerization. Epoxy resin/silica nanocomposites are subsequently synthesized with these plasma-polymerized nanoparticles. It is found that plasma at a low power (i.e., 10 W can significantly increase the concentration of C–O bonds on the surface of silica nanoparticles. This plasma polymerized thin layer can not only improve the dispersion uniformity by increasing the hydrophilicity of the nanoparticles, but also provide anchoring sites to enable the formation of covalent bonds between the organic and inorganic phases. Furthermore, electrical tests reveal improved electrical treeing resistance and decreased dielectric constant of the synthesized nanocomposites, while the dielectric loss of the nanocomposites remains unchanged as compared to the pure epoxy resin.

  10. Investigating of the Knocking Out Properties of Moulding Sands with New Inorganic Binders Used for Castings of Non-ferrous Metal Alloys in Comparison with the Previously Used

    Directory of Open Access Journals (Sweden)

    I. Izdebska-Szanda

    2012-12-01

    Full Text Available The article presents the results of investigations, which make a fragment of the broad-scale studies carried out as a part of the projectPOIG.01.01.02-00-015/09 “Advanced materials and technologies”.One of the objectives of the introduction of new inorganic binders is to provide a good knocking out properties of moulding sands, whilemaintaining an appropriate level of strength properties.Therefore, a logical continuation of the previous studies were carried out the tests knocking out properties of moulding sands with newinorganic binders, including making moulds, pouring them by the chosen of non-ferrous metal alloys, knoking-out, and determining theknocking out work.The results of the study were related to the research results obtained by applying the moulding sand performed by existing technology.

  11. Advanced polymer-inorganic hybrid hard coatings utilizing in situ polymerization method.

    Science.gov (United States)

    Takaki, Toshihiko; Nishiura, Katsunori; Mizuta, Yasushi; Itou, Yuichi

    2006-12-01

    Hard coatings are frequently used to give plastics high scratch resistance. Coating hardness and adhesion to the substrate are considered to be key factors influencing scratch resistance, but it is difficult to produce coatings that have both properties. Hybridization of polymers and inorganic materials is a promising approach for solving this problem. We prepared polymer-silica hybrid coatings by using in situ polymerization to carry out radical polymerization of vinyl monomers in a sol-gel solution of alkoxysilanes, and measured the abrasion resistance of the coatings. However, the expected properties were not obtained because the sol-gel reaction did not perfectly proceed on the surface of the coatings under the N2 conditions. We found that curing the hybrid coatings by UV irradiation in air promoted the sol-gel reaction on the surface, resulting in coatings having excellent abrasion resistance.

  12. Preparation of new hybrid organic/inorganic polymeric chiral stationary phases for ligand-exchange chromatography

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Three new hybrid organic/inorganic polymeric ligand-exchange chiral stationary phases were developed by radical chain transfer reaction and surface grafting on silica gel, and successfully used for the enantioseparations of DL-amino acids and DL-hydroxyl acids. The resolutions were achieved by using water containing 2.0 × 10-4 mol/L of CuAc2 as a mobile phase, column temperature of 40 ℃, flow rate of 1.0 mL/min and detection at UV 254 mn. The elution order of D-isomer before L-isomer was observed for all DL-amino acids resolved except DL-Pro.

  13. 聚合物基有机-无机纳米复合材料的制备、性能及应用%Preparation, Properties and Application of Polymeric Organic-Inorganic Nanocomposites

    Institute of Scientific and Technical Information of China (English)

    任杰; 刘艳; 唐小真

    2003-01-01

    Six preparation methods for polymeric organic-inorganic nanocomposites and their respective mecha-nisms and features are reviewed. The extraordinary properties of polymeric organic-inorganic nanocomposites arediscussed,and their potential applications are evaluated.

  14. The Effects of Various Conductive Additive and Polymeric Binder Contents on the Performance of a Lithium-ion Composite

    Energy Technology Data Exchange (ETDEWEB)

    Stevenson, Cynthia; Liu, G.; Zheng, H.; Kim, S.; Deng, Y.; Minor, A.M.; Song, X.; Battaglia, V.S.

    2008-08-07

    Fundamental electrochemical methods, cell performance tests, and physical characterization tests such as electron microscopy were used to study the effects of levels of the inert materials (acetylene black (AB), a nano-conductive additive, and polyvinylidene difluoride (PVDF), a polymer binder) on the power performance of lithium-ion composite cathodes. The electronic conductivity of the AB/PVDF composites at different compositions was measured with a four-point probe direct current method. The electronic conductivity was found to increase rapidly and plateau at a AB:PVDF ratio 0.2:1 (by weight), with 0.8:1 being the highest conductivity composition. AB:PVDF compositions along the plateau of 0.2:1, 0.4:1, 0.6:1 and 0.8:1 were investigated. Electrodes of each of those compositions were fabricated with different fractions of AB/PVDF to active material. It was found that at the 0.8:1 AB:PVDF, the rate performance improved with increases in the AB/PVDF loading, whereas at the 0.2:1 AB:PVDF, the rate performance improved with decreases in the AB/PVDF loading. The impedance of electrodes made with 0.6:1 AB:PVDF was low and relatively invariant.

  15. ROMP-Derived cyclooctene-based monolithic polymeric materials reinforced with inorganic nanoparticles for applications in tissue engineering

    Directory of Open Access Journals (Sweden)

    Franziska Weichelt

    2010-12-01

    Full Text Available Porous monolithic inorganic/polymeric hybrid materials have been prepared via ring-opening metathesis copolymerization starting from a highly polar monomer, i.e., cis-5-cyclooctene-trans-1,2-diol and a 7-oxanorborn-2-ene-derived cross-linker in the presence of porogenic solvents and two types of inorganic nanoparticles (i.e., CaCO3 and calcium hydroxyapatite, respectively using the third-generation Grubbs initiator RuCl2(Py2(IMesH2(CHPh. The physico-chemical properties of the monolithic materials, such as pore size distribution and microhardness were studied with regard to the nanoparticle type and content. Moreover, the reinforced monoliths were tested for the possible use as scaffold materials in tissue engineering, by carrying out cell cultivation experiments with human adipose tissue-derived stromal cells.

  16. Organic-inorganic random copolymers from methacrylate-terminated poly(ethylene oxide) with 3-methacryloxypropylheptaphenyl polyhedral oligomeric silsesquioxane: synthesis via RAFT polymerization and self-assembly behavior.

    Science.gov (United States)

    Wei, Kun; Li, Lei; Zheng, Sixun; Wang, Ge; Liang, Qi

    2014-01-14

    In this contribution, we report the synthesis of organic-inorganic random polymers from methacrylate-terminated poly(ethylene oxide) (MAPEO) (Mn = 950) and 3-methacryloxypropylheptaphenyl polyhedral oligomeric silsesquioxane (MAPOSS) macromers via reversible addition-fragmentation chain transfer (RAFT) polymerization with 4-cyano-4-(thiobenzoylthio) valeric acid (CTBTVA) as the chain transfer agent. The organic-inorganic random copolymers were characterized by means of (1)H NMR spectroscopy, gel permeation chromatography (GPC) and differential scanning calorimetry (DSC). The results of GPC indicate that the polymerizations were carried out in a controlled fashion. Transmission electron microscopy (TEM) showed that the organic-inorganic random copolymers in bulk were microphase-separated and the POSS microdomains were formed via POSS-POSS interactions. In aqueous solutions the organic-inorganic random copolymers were capable of self-assembling into spherical nanoobjects as evidenced by transmission electron microscopy (TEM) and dynamic laser scattering (DLS). The self-assembly behavior of the organic-inorganic random copolymers was also found to occur in the mixtures with the precursors of epoxy. The nanostructures were further fixed via subsequent curing reaction and thus the organic-inorganic nanocomposites were obtained. The formation of nanophases in epoxy thermosets was confirmed by transmission electron microscopy (TEM) and dynamic mechanical thermal analysis (DMTA). The organic-inorganic nanocomposites displayed the enhanced surface hydrophobicity as evidenced by surface contact angle measurements.

  17. Colloidal interactions of inorganic nanoparticles grafted with zwitterionic polymer brushes and gels by surface-mediated seeded polymerization.

    Science.gov (United States)

    An, Soyoun; Choi, Sang Koo; Cho, Jang Woo; Kim, Hyun Tae; Kim, Jin Woong

    2014-08-01

    A robust and straightforward approach is introduced to synthesize inorganic nanoparticles chemically grafted with a zwitterionic poly(2-methacryroyloxyethylphosphorylcholine) (PMPC) thin layers. The synthesis method is based on the surface-mediated seeded polymerization. In order to observe how the polymer chain architectures affect colloidal interactions, the zinc oxide nanoparticles are grafted with linear brushes and with a thin hydrogel layer, respectively. The thickness of PMPC shell layers spans a few nanometers. The studies on suspension rheology for the nanoparticles show that the nanoparticles with PMPC brushes show the stronger repulsive force than those with the PMPC gel shell due to the entropic stabilization. When the shear force is applied to the Pickering emulsion produced by assembly of the nanoparticles, it is noticeable that the presence of PMPC brushes on the particles rather enhances the drop-to-drop attraction, which presumably stems from the entanglement of polymer chains between the contacted interfacial planes of the emulsion droplets during shearing.

  18. Organic-inorganic hybrid protonic polymeric electrolytes grafted by sulfonic acid/sulfonamide moieties

    Energy Technology Data Exchange (ETDEWEB)

    Depre, L.; Poinsignon, C.; Popall, M.

    2000-07-01

    Thin proton conducting membranes of an organic-inorganic polymer electrolyte bearing sulphonamide and sulfonic groups are prepared by sol-gel process. Polycondensation of alkoxysilanes provides the inorganic silicate backbone whereas the organic network is formed from reactive functional groups R{prime}(({minus}DH{sub 2}){sub 3}-SO{sub 3}H) and [({minus}CH{sub 2}){sub 3}-SO{sub 2}NH{sub 2}] of alkoxysilanes of R{prime}Si[OR{sub 3}] type. Proton conductivity measured in the dry and wet state under controlled Temperature and Relative Humidity increases from 10{sup {minus}4} S/cm under vacuum to 6 10{sup {minus}2} S/cm at 70 C and 96% RH. Conductivity dependence on temperature and associated conduction mechanisms are discussed in both states.

  19. Preparation a new sorbent based on polymeric ionic liquid for stir cake sorptive extraction of organic compounds and inorganic anions.

    Science.gov (United States)

    Huang, Xiaojia; Wang, Yulei; Hong, Qiuyun; Liu, Yi; Yuan, Dongxing

    2013-11-01

    A new multi-interaction sorbent (MIS) based on polymeric ionic liquid was prepared and used as extractive medium of stir cake sorptive extraction (SCSE). In the presence of dimethyl sulfoxide, an ionic liquid, 1-vinylbenzyl-3-methylimidazolium chloride was used as monomer to copolymerize in situ with divinylbenzene to form the MIS. The influences of the content of monomer and the porogen solvent in the polymerization mixture on the extraction performance were investigated thoroughly. The MIS was characterized by infrared spectroscopy, elemental analysis, scanning electron microscopy and mercury intrusion porosimetry. Parabens and aromatic amines were used to investigate the extraction performance of MIS-SCSE for apolar and strongly polar analytes, respectively. The extraction parameters for parabens and aromatic amines were optimized. At the same time, simple and sensitive analytical methods for parabens and aromatic amines in real samples were developed by the combination of MIS-SCSE and HPLC/DAD. Some inorganic anions, such as F(-), Br(-), NO3(-), PO4(3-) and SO4(2-), were used to test the extraction performance of MIS-SCSE for anions. Results indicated that mechanism involved in the extraction of MIS is the multi-interaction modes including π-π, hydrophobic, hydrogen-bonding, dipole-dipole and anion-exchange interactions.

  20. Aggregation kinetics of inorganic colloids in eutrophic shallow lakes: Influence of cyanobacterial extracellular polymeric substances and electrolyte cations.

    Science.gov (United States)

    Xu, Huacheng; Yang, Changming; Jiang, Helong

    2016-12-01

    The stability/aggregation propensity of inorganic colloids in eutrophic shallow lakes is of great essence in governing the water transparency and contaminant behavior. In this study, time-resolved dynamic light scattering was employed to investigate the aggregation kinetics of Al2O3 inorganic colloids over a wide range of cyanobacterial extracellular polymeric substance (EPS) concentrations in the absence and presence of electrolyte cations. The results showed that EPS adsorption alone greatly decreased the hydrodynamic diameters of colloidal particles, whose stability behavior followed closely the predictions of the classical DLVO theory. Electrolyte cations, however, can induce the aggregation of colloidal particles, and divalent Ca(2+) were found to be more efficient in destabilizing the colloids than monovalent Na(+), as indicated by the considerably lower critical coagulation concentrations (2.5 mM for Ca(2+) vs. 170 mM for Na(+)). Further addition of Ca(2+), i.e., >2.5 mM, caused an extremely high aggregation degree and rate. High resolution transmission electron microscopy revealed that this enhanced aggregation should be attributed to the gel-like bridging between colloidal particles, which were verified to be the amorphous EPS-Ca(2+) complexes. Field-emission scanning electron microscopy coupled with elemental mapping provided additional evidence that the bridging interaction of EPS with Ca(2+) was the predominant mechanism for the aggregation enhancement. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Silicateins--a novel paradigm in bioinorganic chemistry: enzymatic synthesis of inorganic polymeric silica.

    Science.gov (United States)

    Müller, Werner E G; Schröder, Heinz C; Burghard, Zaklina; Pisignano, Dario; Wang, Xiaohong

    2013-05-03

    The inorganic matrix of the siliceous skeletal elements of sponges, that is, spicules, is formed of amorphous biosilica. Until a decade ago, it remained unclear how the hard biosilica monoliths of the spicules are formed in sponges that live in a silica-poor (<50 μM) aquatic environment. The following two discoveries caused a paradigm shift and allowed an elucidation of the processes underlying spicule formation; first the discovery that in the spicules only one major protein, silicatein, exists and second, that this protein displays a bio-catalytical, enzymatic function. These findings caused a paradigm shift, since silicatein is the first enzyme that catalyzes the formation of an inorganic polymer from an inorganic monomeric substrate. In the present review the successive steps, following the synthesis of the silicatein product, biosilica, and resulting in the formation of the hard monolithic spicules is given. The new insight is assumed to open new horizons in the field of biotechnology and also in biomedicine.

  2. Advances in Organic and Organic-Inorganic Hybrid Polymeric Supports for Catalytic Applications

    Directory of Open Access Journals (Sweden)

    Anna Maria Pia Salvo

    2016-09-01

    Full Text Available In this review, the most recent advances (2014–2016 on the synthesis of new polymer-supported catalysts are reported, focusing the attention on the synthetic strategies developed for their preparation. The polymer-supported catalysts examined will be organic-based polymers and organic-inorganic hybrids and will include, among others, polystyrenes, poly-ionic liquids, chiral ionic polymers, dendrimers, carbon nanotubes, as well as silica and halloysite-based catalysts. Selected examples will show the synthesis and application in the field of organocatalysis and metal-based catalysis both for non-asymmetric and asymmetric transformations.

  3. Polymeric media comprising polybenzimidazoles N-substituted with organic-inorganic hybrid moiety

    Science.gov (United States)

    Klaehn, John R [Idaho Falls, ID; Peterson, Eric S [Idaho Falls, ID; Wertsching, Alan K [Idaho Falls, ID; Orme, Christopher J [Shelley, ID; Luther, Thomas A [Idaho Falls, ID; Jones, Michael G [Pocatello, ID

    2009-12-15

    A PBI compound includes imidazole nitrogens at least a portion of which are substituted with an organic-inorganic hybrid moiety may be included in a separator medium. At least 85% of the imidazole nitrogens may be substituted. The organic-inorganic hybrid moiety may be an organosilane moiety, for example, (R)Me.sub.2SiCH.sub.2-- where R is selected from among methyl, phenyl, vinyl, and allyl. The separatory medium may exhibit an H.sub.2, Ar, N.sub.2, O.sub.2, CH.sub.3, or CO.sub.2 gas permeability greater than the gas permeability of a comparable separatory medium comprising the PBI compound without substitution. The separatory medium may further include an electronically conductive medium and/or ionically conductive medium. The separatory medium may be used as a membrane (semi-permeable, permeable, and non-permeable), a barrier, an ion exhcange media, a filter, a gas chromatography coating (such as stationary phase coating in affinity chromatography), etc.

  4. A new polymeric ionic liquid-based magnetic adsorbent for the extraction of inorganic anions in water samples.

    Science.gov (United States)

    Chen, Lei; Huang, Xiaojia; Zhang, Yong; Yuan, Dongxing

    2015-07-17

    In this work, a novel type of polymeric ionic liquid (PIL)-based magnetic adsorbent was successfully synthesized and applied for the extraction and determination of seven inorganic anions in water samples by coupling with ion chromatography. The new adsorbent was synthesized by simple free radical copolymerization of 1-ally-3-vinylimidazolium chloride, ethylene glycol dimethacrylate and silica-coated magnetite. The adsorbent exhibited well-defined core-shell structure and good magnetic response ability. Furthermore, due to the presence of abundant anion-exchange groups in the PIL, the adsorbent displayed expected extraction performance for anions including F(-), Cl(-), Br(-), NO2(-), NO3(-), PO4(3-) and SO4(2-). Various experimental parameters that could affect the extraction performance, such as the amount of adsorbent, desorption solvent, extraction and desorption time, the pH value of sample solution were investigated in detail. Under the optimized conditions, low limits of detection (S/N=3) and quantification limits (S/N=10) of the proposed method for the target anions were achieved within the range of 0.061-0.73μg/L and 0.19-2.41μg/L, respectively. The repeatability was investigated by evaluating the intra-day, inter-day precisions and batch-to-batch reproducibility with relative standard deviations (RSDs) lower than 11%. At the same time, the method also showed high extraction speed, simplicity, practicality and low cost for the extraction inorganic anions. Finally, the proposed method was used to detect anions in different water samples successfully. The recoveries were in the range of 71.0-111%, and the RSDs were below 12% in the all cases.

  5. The patterning of sub-500 nm inorganic oxide and semiconducting polymeric structures

    Science.gov (United States)

    Hampton, Meredith J.; Williams, Stuart S.; Zhou, Zhilian; Nunes, Janine; Ko, Doo-Hyun; Templeton, Joseph L.; DeSimone, Joseph M.; Samulski, Edward T.

    2008-08-01

    The Pattern Replication In Non-wetting Templates (PRINT) technique has been extended to patterning of isolated features as well as embossed films of sub-500 nm "hard" inorganic oxides and nanocrystalline semiconductors and "soft" semiconducting polymers including TiO2, SnO2, ZnO, ITO, BaTiO3, CdSe, poly(3-hexylthiophene) (P3HT), Poly[2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylenevinylene] (MDMO-PPV), and other polythiophene derivatives. The low surface energy, chemically resistant, air permeable elastomeric perflouropolyether (PFPE) based molds allow for numerous materials to be patterned on a variety of substrates including glass, transparent conductive oxides, and thin films of conducting polymer for a wide range of electronic and optical applications. Additionally, PRINT has been employed to pattern features with aspect ratios greater than 1, deposit a second layer of features on top of an initial layer without pattern destruction, and replicate sub-100 nm sized features for photovoltaics applications. Materials and patterns generated in this work were characterized using a variety of techniques including: Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and X-ray Diffraction (XRD).

  6. STUDY ON POLYMERIC CATALYST—PALLADIUM COMPLEX WITH RADIATION GRAFTING ACRYLONITRILE ON INORGANIC COMPOUND

    Institute of Scientific and Technical Information of China (English)

    ZHANGWanxi; CHEJitai

    1993-01-01

    Polymer bound palladium (Pd) complex catalysts with grafting acrylonitrile on inorganic compound(MgO,Y-molecular sieve and SiO2) by pre-radiation method were studies.The palladium-grafting polymers have been investigated by X-ray photoelectron spectrscopy(XPS).It is indicated that peak width of C1s and O1s spectra of MgO-g-PAN-Pd(radiation-induced graft) is wider than that of MgO-PAN-Pd(chemical method) and Peak numbers of former are one more than later.According to the report in reference,this peak is attributed to -O-C group.Thus,the graft acrylonitrile on MgO may complete through oxygen atoms im MgO and β-carbon atoms in acrylonitrile.The polymer catalyst obtained by radiation grafting is a higher active hydrogenation catalyst for olefines and better antioxic than that of one obtained by chemical method,and it has selectivity for hydrogenation catalyst.

  7. Enzymatic polymerization of aniline in the presence of different inorganic substrates

    Energy Technology Data Exchange (ETDEWEB)

    Flores-Loyola, E. [Centro de Investigacion en Quimica Aplicada, Blvd. Enrique Reyna No. 140, CP 25100 Saltillo, Coah (Mexico); Escuela de Ciencias Biologicas, UA de C. Carr. Torreon-Matamoros Km 7.5, Ciudad Universitaria, CP 27400 Torreon, Coah. (Mexico)], E-mail: erika-flores@mail.uadec.mx; Cruz-Silva, R. [Centro de Investigacion en Ingenieria y Ciencias Aplicadas, UAEM. Av. Universidad 1001, Col. Chamilpa, CP 62210, Cuernavaca Mor. (Mexico); Romero-Garcia, J.; Angulo-Sanchez, J.L. [Centro de Investigacion en Quimica Aplicada, Blvd. Enrique Reyna No. 140, CP 25100 Saltillo, Coah (Mexico); Castillon, F.F.; Farias, M.H. [Centro de Ciencias de la Materia Condensada de la UNAM, Apdo. Postal 2681, CP 22800 Ensenada, B.C. (Mexico)

    2007-09-15

    The effect of different inorganic substrates in the structure of polyaniline synthesized by enzymatic oxidation was studied. The polymer characterization was done by electronic absorption and X-ray photoelectron spectroscopy. The substrates studied were: controlled pore glass, mordenite, zeolite Y, zeolite MCM-41, Wollastonite, silica gel, fuming silica and short glass fibers type E. Polyaniline was synthesized in the presence of the substrates under acidic aqueous conditions, using hydrogen peroxide as oxidizer and HRP or SBP enzymes as catalyst. The composition of the substrates strongly affected the degree of electronic conjugation of the synthesized polyaniline, whereas the pore size and the enzyme type apparently had no effect. The chemical structure of polyaniline enzymatically synthesized was more sensitive to the substrate composition than that chemically synthesized. Apparently substrates containing alkaline ions, such as sodium and calcium, promoted the formation of the branched, non-conductive polyaniline form. The effect of the substrates on the polyaniline structure can be explained considering the local pH effect of the templates surface on the coupling reaction of aniline radicals.

  8. Rheological characteristics of synthetic road binders

    Energy Technology Data Exchange (ETDEWEB)

    Gordon D. Airey; Musarrat H. Mohammed; Caroline Fichter [University of Nottingham, Nottingham (United Kingdom)

    2008-08-15

    This paper deals with the synthesis of polymer binders from monomers that could in future be derived from renewable resources. These binders consist of polyethyl acrylate (PEA) of different molecular weight, polymethyl acrylate (PMA) and polybutyl acrylate (PBA), which were synthesised from ethyl acrylate, methyl acrylate and butyl acrylate, respectively, by atom transfer radical polymerization (ATRP). The fundamental rheological properties of these binders were determined by means of a dynamic shear rheometer (DSR) using a combination of temperature and frequency sweeps. The results indicate that PEA has rheological properties similar to that of 100/150 penetration grade bitumen, PMA similar rheological properties to that of 10/20 penetration grade bitumen, while PBA, due to its highly viscous nature and low complex modulus, cannot be used on its own as an asphalt binder. The synthetic binders were also combined with conventional penetration grade bitumen to produce a range of bitumen-synthetic polymer binder blends. These blends were batched by mass in the ratio of 1:1 or 3:1 and subjected to the same DSR rheological testing as the synthetic binders. The blends consisting of a softer bitumen (70/100 pen or 100/150 pen) with a hard synthetic binder (PMA) tended to be more compatible and therefore stable and produced rheological properties that combined the properties of the two components. The synthetic binders and particularly the extended bitumen samples (blends) produced rheological properties that showed similar characteristics to elastomeric SBS PMBs. 30 refs., 12 figs., 2 tabs.

  9. Synthesis of an imprinted hybrid organic-inorganic polymeric sol-gel matrix toward the specific binding and isotherm kinetics investigation of creatinine.

    Science.gov (United States)

    Chang, Yong-Sheun; Ko, Ting-Hsien; Hsu, Ting-Jung; Syu, Mei-Jywan

    2009-03-15

    Hybrid organic-inorganic polymeric sol-gel materials imprinted with creatinine template molecules were synthesized for the specific binding of creatinine. Creatinine is a metabolite from creatine and is the final product from kidney metabolism. Therefore, creatinine can be an important index to estimate the function of the kidney. It was then chosen as the target molecule in this work. To achieve the specific binding toward creatinine, molecular imprinting was used to create a polymeric matrix for the regarding purpose. Sol-gel was further added to create a rigid network structure for the absorption of creatinine. An inorganic precursor, tetraethoxysilane (TEOS), was mixed with an organic functional monomer, 2-acrylamido-2-methylpropane-sulfonic acid (AMPS), and the creatinine template to form a hybrid organic-inorganic imprinted polymer. The chemical functionality was achieved as well as a confined matrix via the polymerization and the hydrolysis-condensation of the sol-gel. The imprinting effect from the hybrid materials against the corresponding nonimprinted was investigated. BET (Brunauer-Emmett-Teller) analysis was carried out for the imprinted and the nonimprinted materials. The specificity of the hybrid materials was further examined by capping the surface silanol groups with chloro-trimethylsilane (CTMS) and 1,1,1,3,3,3-hexamethyldisilazane (HMDS), respectively. The capping effect was compared and discussed from the binding results. Selectivity of the materials toward creatinine was obtained using mixture solutions in the presence of creatinine and its analogues. Reutilization and storage stability of the hybrid organic-inorganic imprinted material were also studied. Additionally, the affinity distribution of the hybrid imprinted materials derived from the allosteric model was also analyzed from the adsorption isotherm data.

  10. The effect of sodium hydroxide treatment on biomass binder preparation

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X.; Xu, D.; Xu, Z.; Chen, Q. [China University of Mining and Technology, Beijing (China). Beijing Campus

    2001-02-01

    The possibility of rice straw which has been treated with sodium hydroxide for use as coal briquette binder was studied. The main factor which influenced the binder preparation was the concentration of sodium hydroxide. It was found that the binding ability of the solid component was higher than the liquid part. The prepared rice straw binder was mixed with inorganic material, bentonite, or high molecular synthetic organic materials to manufacture a compound coal briquette binder. This compound binder is waterproofing and can further enhance the strength of the briquette. 5 refs., 5 figs., 2 tabs.

  11. Polymeric and Inorganic Fibers

    Science.gov (United States)

    This series presents critical reviews of the present and future trends in polymer and biopolymer science including chemistry, physical chemistry, physics and materials science. It is addressed to all scientists at universities and in industry who wish to keep abreast of advances in the topics covered. Impact Factor Ranking: Always number one in Polymer Science. More information as well as the electronic version of the whole content available at: www.springerlink.

  12. Selective and Sequential Re-Assembly of Patterned Block Copolymer Thin Film for Fabricating Polymeric, Inorganic, and Their Composite Nanostructured Arrays.

    Science.gov (United States)

    Zu, Xihong; Gong, Jian; Tu, Weiping; Deng, Yulin

    2011-10-04

    We report that the nanostructures of poly(styrene-block-4-vinylpyridine) block copolymer (PS-b-P4VP) thin film on a wafer substrate can be re-assembled by sequential vapor treatment using selected solvents. Metal or other inorganic nanoparticles that were randomly pre-loaded inside or on the surface of PS-b-P4VP thin film could be pulled to the rim of PS and P4VP along with the movements of PS and P4VP blocks during the treatment. As a result, the patterned polymeric or inorganic/polymer composite nanoisland and nanoring arrays were fabricated. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Preparation of a new polymeric ionic liquid-based monolith for stir cake sorptive extraction and its application in the extraction of inorganic anions.

    Science.gov (United States)

    Huang, Xiaojia; Chen, Linli; Yuan, Dongxing; Bi, Shangshang

    2012-07-27

    In this study, a novel stir cake sorptive extraction (SCSE) sorbent based on polymeric ionic liquid-based monolith (PILM) for the extraction of inorganic anions was prepared. In the presence of a porogen solvent containing 1-propanol and dimethylformamid, an ionic liquid, 1-ally-3-methylimidazolium chloride was used as monomer to copolymerize in situ with ethylene dimethacrylate to form PILM. The effect of preparation conditions such as ratio of functional monomer to cross-linker, content of porogenic solvent on the extraction efficiencies were investigated in detail. The PILM was characterized by elemental analysis, scanning electron microscopy, mercury intrusion porosimetry and infrared spectroscopy. In order to investigate the extraction capacity of PILM-SCSE for inorganic anions, the SCSE was combined with ion chromatography with conductivity detection, F(-), Cl(-), NO(2)(-), Br(-), NO(3)(-), PO(4)(3-) and SO(4)(2-) were selected as detected solutes. Several extractive parameters, including pH values in sample matrix, desorption solvent, extraction and desorption time were optimized. The results showed that under the optimum experimental conditions, low detection limits (S/N=3) and quantification limits (S/N=10) of the proposed method for the target anions were achieved within the range of 0.11-2.08 and 0.37-6.88 μg/L, respectively. The method also showed good linearity, simplicity, practicality and low cost for the extraction inorganic anions. Finally, the proposed method was successfully used to detect different water samples include commercial purified water, tab water and river water. Acceptable recoveries and satisfactory repeatability were obtained. To the best of our knowledge, this is the first to use polymeric ionic liquid to enrich inorganic anions.

  14. Metal-phosphate binders

    Science.gov (United States)

    Howe, Beth Ann [Lewistown, IL; Chaps-Cabrera, Jesus Guadalupe [Coahuila, MX

    2009-05-12

    A metal-phosphate binder is provided. The binder may include an aqueous phosphoric acid solution, a metal-cation donor including a metal other than aluminum, an aluminum-cation donor, and a non-carbohydrate electron donor.

  15. Anionic surface binders

    Directory of Open Access Journals (Sweden)

    Aljaž-Rožič Mateja

    2004-01-01

    Full Text Available The MELAMIN Chemical Factory in Kočevje manufactures synthetic resins and binders for the paper industry. Binders based on AKD (alkyl ketene dimer are produced which are used for binding paper and cardboard in the range of neutral and partially basic pH. Cationic and, lately, anionic binders are mostly used for the bulk binding of paper and board. The possibility of using AKD binders on paper or board surfaces is presented. In this case partially cationic AKD binders may be applied. When optical whiteners are used, the application of AKD binders is recommended. In the case of paper it is possible to substitute acrylate binders by AKD binders. The best results are obtained when the paper is first partly treated in bulk and subsequently surface treated.

  16. Organic/Inorganic Nanocomposites Prepared by Miniemulsion Polymerization%细乳液聚合法制备有机/无机纳米复合材料

    Institute of Scientific and Technical Information of China (English)

    高党鸽; 梁志扬; 吕斌; 马建中

    2016-01-01

    无机纳米粒子的引入可以使聚合物材料获得抗菌、导电和防紫外等诸多特性,但无机纳米粒子在聚合物基质中易团聚、引入量少,难以充分发挥其优点.细乳液聚合法基于其独特的成核方式——液滴成核,能够提高无机纳米粒子在聚合物基中的分散性和引入量,且复合材料的形貌易于控制,是目前制备特殊形貌有机/无机纳米复合材料的一种有效手段.本文介绍了有机/无机复合纳米材料的细乳液制备过程,综述了近年来不同无机纳米粒子与有机基质复合的研究进展,例如:纳米SiO2、纳米ZnO、金属纳米粒子、纳米氧化石墨烯等.最后就其发展现状提出了几点建议.%The introduction of inorganic nanoparticles can make the polymer materials many characteristics,such as antibacterial,conductive,anti-ultraviolet.However,the inorganic nanoparticles are easy to agglomerate and less content of nanoparticles is introduced in polymer,so it is difficult to demonstrate advantage of nano material.Based on its unique droplet nucleation mechanism,miniemulsion polymerization can improve the inorganic nanoparticles' dispersity and amount of introduction in polymer matrix,and control the morphology of the composites easily.It is an effective method to obtain the special morphology of organic/inorganic nanocomposites.This paper introduces the preparation process of organic/inorganic nanocomposite miniemulsion,and reviews the recent progress of different inorganic nanoparticles with organic matrix composites,such as nano-SiO2,nano-ZnO,metal nanoparticles,nano-graphene oxide,etc.At last,some suggestions on the present development situation are given.

  17. Antibacterial inorganic-organic hybrid coatings on stainless steel via consecutive surface-initiated atom transfer radical polymerization for biocorrosion prevention.

    Science.gov (United States)

    Yuan, S J; Pehkonen, S O; Ting, Y P; Neoh, K G; Kang, E T

    2010-05-04

    To enhance the corrosion resistance of stainless steel (SS) and to impart its surface with antibacterial functionality for inhibiting biofilm formation and biocorrosion, well-defined inorganic-organic hybrid coatings, consisting of a polysilsesquioxane inner layer and quaternized poly(2-(dimethyamino)ethyl methacrylate) (P(DMAEMA)) outer blocks, were prepared via successive surface-initiated atom transfer radical polymerization (ATRP) of 3-(trimethoxysilyl)propyl methacrylate (TMSPMA) and 2-(dimethylamino)ethyl methacrylate (DMAEMA). The cross-linked P(TMASPMA), or polysilsesquioxane, inner layer provided a durable and resistant coating to electrolytes. The pendant tertiary amino groups of the P(DMAEMA) outer block were quaternized with alkyl halide to produce a high concentration of quaternary ammonium groups with biocidal functionality. The so-synthesized inorganic-organic hybrid coatings on the SS substrates exhibited good anticorrosion and antibacterial effects and inhibited biocorrosion induced by sulfate-reducing bacteria (SRB) in seawater media, as revealed by antibacterial assay and electrochemical analyses, and they are potentially useful to steel-based equipment under harsh industrial and marine environments.

  18. Mechanically activated fly ash as a high performance binder for civil engineering

    Science.gov (United States)

    Rieger, D.; Kullová, L.; Čekalová, M.; Novotný, P.; Pola, M.

    2017-01-01

    This study is aimed for investigation of fly ash binder with suitable properties for civil engineering needs. The fly ash from Czech brown coal power plant Prunerov II was used and mechanically activated to achieve suitable particle size for alkaline activation of hardening process. This process is driven by dissolution of aluminosilicate content of fly ash and by subsequent development of inorganic polymeric network called geopolymer. Hardening kinetics at 25 and 30 °C were measured by strain controlled small amplitude oscillatory rheometry with strain of 0.01 % and microstructure of hardened binder was evaluated by scanning electron microscopy. Strength development of hardened binder was investigated according to compressional and flexural strength for a period of 180 days. Our investigation finds out, that mechanically activated fly ash can be comparable to metakaolin geopolymers, according to setting time and mechanical parameters even at room temperature curing. Moreover, on the bases of long time strength development, achieved compressional strength of 134.5 after 180 days is comparable to performance of high grade Portland cement concretes.

  19. Study of polymeric hydrogels with inorganic nanoparticles of clay; Estudo de hidrogeis polimericos com nanoparticulas inorganicas de argila

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Maria Jose A. de; Parra, Duclerc F.; Lugao, Ademar B., E-mail: mariajhho@yahoo.com.br, E-mail: dfparra@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP/CQMA), Sao Paulo, SP (Brazil). Centro de Quimica e Meio Ambiente; Amato, Valdir S. [Universidade de Sao Paulo (HC/FMUSP), Sao Paulo, SP (Brazil). Hospital de Clinicas. Divisao de Clinica de Molestias Infecciosas e Parasitarias

    2011-07-01

    Nanoscience has been applied in research of intelligent systems for drug delivery. The use of biodegradable synthetic polymers and in diagnostics and therapy has stimulated the application of nanotechnology in polymeric systems with new structures and new materials composing among these materials are hydrogels. Hydrogel with dispersed clay is a new class of materials that combine flexible and permeability of the hydrogels with the high efficiency of the clay to adsorb different substances. We evaluated the behaviour of swelling, gel fraction and thermal stability among the hydrogels obtained by poly (vinyl alcohol) (PVAl) with clay and poly (N-2-vinyl-pyrrolidone) (PVP) with clay. While, observed that the hydrogels showed swelling clay PVAl meaningful, the clay PVP hydrogels showed swelling more consistent after four hours of testing.

  20. Solvolytic Degradation of Polymeric Propellant Binders

    Science.gov (United States)

    1975-06-01

    Pat. 1,003,713; Chem. Abstr.-, 53, 22982a (1959). ~8. A. Lupu, 1L. Dascalu and 1. Cristescu, Khim. Volokna, No. 3, 25(1962); Chein . Abstr., 57...Chim. Acta, 35, 1;1111(1952); Chem. Abot’r., f9, 23111f -(1953). 23. 14. Bender and Y. Chow, J. Amer. Chein . Soc., 81, 3929 (,1959). 24. C. Overbergc

  1. Phosphate binders in chronic kidney disease: a systematic review of recent data.

    Science.gov (United States)

    Floege, Jürgen

    2016-06-01

    Hyperphosphatemia is common in chronic kidney disease (CKD) and is treated by dietary measures, dialysis techniques and/or phosphate binders. For the present review PubMed was searched for new publications on phosphate binders appearing between January 2010 and October 2015. This review summarizes the latest information on non-pharmacological measures and their problems in lowering phosphate in CKD patients, effects of phosphate binders on morbidity and mortality, adherence to phosphate binder therapy as well as new information on specific aspects of the various phosphate binders on the market: calcium acetate, calcium carbonate, magnesium-containing phosphate binders, polymeric phosphate binders (sevelamer, bixalomer, colestilan), lanthanum carbonate, ferric citrate, sucroferric oxyhydroxide, aluminum-containing phosphate binders, and new compounds in development. The review also briefly covers the emerging field of drugs targeting intestinal phosphate transporters.

  2. Organic-skinned inorganic nanoparticles: surface-confined polymerization of 6-(3-thienylhexanoic acid bound to nanocrystalline TiO2

    Directory of Open Access Journals (Sweden)

    Saji Viswanathan

    2011-01-01

    Full Text Available Abstract There are many practical difficulties in direct adsorption of polymers onto nanocrystalline inorganic oxide surface such as Al2O3 and TiO2 mainly due to the insolubility of polymers in solvents or polymer agglomeration during adsorption process. As an alternative approach to the direct polymer adsorption, we propose surface-bound polymerization of pre-adsorbed monomers. 6-(3-Thienylhexanoic acid (THA was used as a monomer for poly[3-(5-carboxypentylthiophene-2,5-diyl] (PTHA. PTHA-coated nanocrystalline TiO2/FTO glass electrodes were prepared by immersing THA-adsorbed electrodes in FeCl3 oxidant solution. Characterization by ultraviolet/visible/infrared spectroscopy and thermal analysis showed that the monolayer of regiorandom-structured PTHA was successfully formed from intermolecular bonding between neighbored THA surface-bound to TiO2. The anchoring functional groups (-COOH of the surface-crawling PTHA were completely utilized for strong bonding to the surface of TiO2.

  3. Inorganic-organic hybrid coatings on stainless steel by layer-by-layer deposition and surface-initiated atom-transfer-radical polymerization for combating biocorrosion.

    Science.gov (United States)

    Yuan, S J; Pehkonen, S O; Ting, Y P; Neoh, K G; Kang, E T

    2009-03-01

    To improve the biocorrosion resistance of stainless steel (SS) and to confer the bactericidal function on its surface for inhibiting bacterial adhesion and biofilm formation, well-defined inorganic-organic hybrid coatings, consisting of the inner compact titanium oxide multilayers and outer dense poly(vinyl-N-hexylpyridinium) brushes, were successfully developed. Nanostructured titanium oxide multilayer coatings were first built up on the SS substrates via the layer-by-layer sol-gel deposition process. The trichlorosilane coupling agent, containing the alkyl halide atom-transfer-radical polymerization (ATRP) initiator, was subsequently immobilized on the titanium oxide coatings for surface-initiated ATRP of 4-vinylpyridine (4VP). The pyridium nitrogen moieties of the covalently immobilized 4VP polymer, or P(4VP), brushes were quaternized with hexyl bromide to produce a high concentration of quaternary ammonium salt on the SS surfaces. The excellent antibacterial efficiency of the grafted polycations, poly(vinyl-N-pyridinium bromide), was revealed by viable cell counts and atomic force microscopy images of the surface. The effectiveness of the hybrid coatings in corrosion protection was verified by the Tafel plot and electrochemical impedance spectroscopy measurements.

  4. Influence of wastewater sludge treatment using combined peroxyacetic acid oxidation and inorganic coagulants re-flocculation on characteristics of extracellular polymeric substances (EPS).

    Science.gov (United States)

    Zhang, Weijun; Cao, Bingdi; Wang, Dongsheng; Ma, Teng; Xia, Hua; Yu, Dehong

    2016-01-01

    Extracellular polymeric substances (EPS) are highly hydrated biopolymers and play important roles in bioflocculation, floc stability, and solid-water separation processes. Destroying EPS structure will result in sludge reduction and release of trapped water. In this study, the effects of combined process of peracetic acid (PAA) pre-oxidation and chemical re-flocculation on morphological properties and distribution and composition of EPS of the resultant sludge flocs were investigated in detail to gain insights into the mechanism involved in sludge treatment. It was found that sludge particles were effectively solubilized and protein-like substances were degraded into small molecules after PAA oxidation. A higher degradation of protein-like substances was observed at acid environments under PAA oxidation. Microscopic analysis revealed that no integral sludge floc was observed after oxidation with PAA at high doses. The floc was reconstructed with addition of inorganic coagulants (polyaluminium chloride (PACl) and ferric chloride (FeCl3)) and PACl performed better in flocculation due to its higher charge neutralization and bridging ability. Combined oxidative lysis and chemical re-flocculation provide a novel solution for sludge treatment.

  5. HMX/TATB/binder development

    Energy Technology Data Exchange (ETDEWEB)

    Stallings, T.L.; Osborn, A.G.; Schaffer, C.L.; Crutchmer, J.A.

    1981-05-01

    The processing and sensitivity characteristics of three HMX/TATB/Binder formulations were investigated. Viton A, Kraton G 1650, and Estane 5702-F1 binders were studied. The thermal stabilities of these compositions are near those of HMX/binder formulations, whereas impact, skid and friction sensitivity levels are less than HMX compositions, but greater than those of TATB/binder systems.

  6. Viscoelastic models for explosive binder materials

    Energy Technology Data Exchange (ETDEWEB)

    Bardenhagen, S.G.; Harstad, E.N.; Maudlin, P.J.; Gray, G.T. [Los Alamos National Lab., NM (United States); Foster, J.C. Jr. [Wright Lab., Eglin AFB, FL (United States)

    1997-07-01

    An improved model of the mechanical properties of the explosive contained in conventional munitions is needed to accurately simulate performance and accident scenarios in weapons storage facilities. A specific class of explosives can he idealized as a mixture of two components: energetic crystals randomly suspended in a polymeric matrix (binder). Strength characteristics of each component material are important in the macroscopic behavior of the composite (explosive). Of interest here is the determination of an appropriate constitutive law for a polyurethane binder material. This paper is a continuation of previous work in modeling polyurethane at moderately high strain rates and for large deformations. Simulation of a large deformation (strains in excess of 100%) Taylor Anvil experiment revealed numerical difficulties which have been addressed. Additional experimental data have been obtained including improved resolution Taylor Anvil data, and stress relaxation data at various strain rates. A thorough evaluation of the candidate viscoelastic constitutive model is made and possible improvements discussed.

  7. Organic - Inorganic Hybrids made from Polymerizable Precursors

    NARCIS (Netherlands)

    Uricanu, V.I.; Donescu, D.; Banu, A.G.; Serban, S.; Olteanu, M.; Dudau, M.

    2004-01-01

    Organic–inorganic hybrid films were prepared based on a recipe using organoalkoxysilanes’ ability to create an inorganic network combined with polymer network formation via radical polymerization of the organic groups. The starting mixtures included different triethoxysilanes (RTES), where the

  8. Breakpoint or Binder

    NARCIS (Netherlands)

    dr. Gürkan Çelik

    2013-01-01

    Civil society as a social sphere is constantly subjected to change. Using the Dutch context, this article addresses the question whether religiously inspired engagement is a binder or a breakpoint in modern societies. The author examines how religiously inspired people in the Netherlands involve the

  9. Binder/HMX interaction in PBX9501 at Elevated Temperatures

    Energy Technology Data Exchange (ETDEWEB)

    K., S C; M., T C

    2003-10-02

    Plastic bonded explosives (PBX) generally consist of 85 - 95 % by weight energetic material, such as HMX, and 5 - 15 % polymeric binder. Understanding of the structure and morphology at elevated temperatures and pressures is important for predicting of PBX behavior in accident scenarios. The crystallographic behavior of pure HMX has been measured as functions of temperature and grain size. The investigation is extended to the high temperature behavior of PBX 9501 (95% HMX, 2.5 % Estane, 2.5 % BDNPA/F). The results show that the HMX {beta}-phase to {delta}-phase transition in PBX 9501 is similar to that in neat HMX. However, in the presence of the PBX 9501 binder, {delta}-phase HMX readily converts back to {beta}-phase during cooling. Using the same temperature profile, the conversion rate decreases for each subsequent heating and cooling cycle. As observed in earlier experiments, no reverse conversion is observed without the polymer binder. It is proposed that the reversion of {delta}-phase to {beta}-phase is due to changes in the surface molecular potential caused by the influence of the polymer binder on the surface molecules of the {delta}-phase. Upon thermal cycling, the polymer binder segregates from the HMX particles and thus reduces the influence of the binder on the surface molecules. This segregation increases the resistance for the {delta}-phase to {beta}-phase transition, as demonstrated in an aged PBX 9501 material for which the reversion is not observed.

  10. Straightforward fabrication of stable white LEDs by embedding of inorganic UV-LEDs into bulk polymerized polymethyl-methacrylate doped with organic dyes

    OpenAIRE

    Di Martino, Daniela; Beverina, Luca; Sassi, Mauro; Brovelli, Sergio; Tubino, Riccardo; Meinardi, Francesco

    2014-01-01

    Stable white-emitting down-converted LEDs are straightforwardly prepared by bulk polymerization of an organic dye doped polymethyl-methacrylate (PMMA) shell directly on top of a highly efficient commercial blue-emitting InGaN LED. Our optimized polymerization procedure allows for extending the form factor of achievable luminescence converter (LUCO) material beyond the conventional thin film form and to directly produce devices with light bulb design. The selected organic dyes, the blue-emitti...

  11. Development of composite solid propellent using dicyclopentadien binder

    Science.gov (United States)

    Bluestone, Stephen Ray

    Through the history of composite solid propellant binders new chemicals are introduced as binders to improve upon the previous generation. Sometimes this is done to improve upon the flaws or shortcomings of a previous binder. Other time it is to meet a new set of requirements desired by industry. Dicyclopentadiene (DCPD) is a hydrocarbon monomer being considered for its potential as a new binder in the composite propellant industry. The binder of a composite solid propellant is arguably the most important feature of the propellant. It is the binder that provides the majority of the structural characteristics of the propellant while also contributing itself as fuel to the combustion process. A binder in composite propellants must also be able to accept the introduction of a large quantity of solid filler; oxidizer, fuel, and other energetic and non-energetic particles. Many of the composite propellants used in industry today have over 80% of their weight composed of non-binder solid or liquid fillers. These requirements must be met by the binder in some form or fashion to produce a propellant able to compete with binders currently in use. When DCPD is polymerized it produces an extremely tough plastic with excellent tensile and impact strength. Experimentation has found that DCPD is able to support a large quantity of solid materials, over 80% weight of the mixture, while still retaining a great portion of its original strength. When compared to another similarly loaded binder currently used in industry, Hydroxyl-Terminated Polybutadiene (HTPB), it was found that DCPD composite propellant had nearly 1.5 times the stress capacity while still exhibiting over 75% of the strain capacity of HTPB based composite propellant. In addition it was also shown that DCPD composite propellant allows for tailoring of its mechanical properties with the addition of plasticizers. The DCPD based composite propellant also exhibits a burning rate nearly twice that HTPB. These factors

  12. Determining the Quantum Efficiency for Activation of an Organometallic Photoinitiator for Cationic Polymerization: An Experiment for the Physical or Inorganic Chemistry Laboratory

    Science.gov (United States)

    Hayes, David M.; Mahar, Maura; Schnabel, R. Chris; Shah, Paras; Lees, Alistair J.; Jakubek, Vladimir

    2007-01-01

    We present a new laboratory experiment on the photochemistry of organometallic [eta][superscript 5],[eta][superscript 6]-mixed-sandwich compounds, which is suitable for both the physical chemistry and inorganic chemistry laboratory. Specifically, students use 1,10-phenanthroline to trap the intermediate formed when…

  13. Recent developments in Inorganic polymers: A Review with focus on Si-Al based inorganic polymers

    Directory of Open Access Journals (Sweden)

    Shrray Srivastava

    2015-12-01

    Full Text Available Inorganic polymers are a unique classification of polymers. They contain inorganic atoms in the main chain. Hybrids with organic polymers as well as those chains that contain metals as pendant groups are considered in a special sub-classification as organo-metallic polymers. The networks containing only inorganic elements in main chain are called inorganic polymers. The silicone rubber is the most commercial inorganic polymer. The organo-metallic and inorganic polymers have a different set of applications. The current paper is a review of current applications of polymers with inorganic back-bone networks, especially focusing on Si and Al based inorganic polymeric materials.

  14. Straightforward fabrication of stable white LEDs by embedding of inorganic UV-LEDs into bulk polymerized polymethyl-methacrylate doped with organic dyes

    Science.gov (United States)

    di Martino, Daniela; Beverina, Luca; Sassi, Mauro; Brovelli, Sergio; Tubino, Riccardo; Meinardi, Francesco

    2014-03-01

    Stable white-emitting down-converted LEDs are straightforwardly prepared by bulk polymerization of an organic dye doped polymethyl-methacrylate (PMMA) shell directly on top of a highly efficient commercial blue-emitting InGaN LED. Our optimized polymerization procedure allows for extending the form factor of achievable luminescence converter (LUCO) material beyond the conventional thin film form and to directly produce devices with light bulb design. The selected organic dyes, the blue-emitting Coumarin 30 and a red-emitting diketopyrrolopyrrole derivative, exhibit high compatibility with the free radical polymerization reaction of the PMMA matrix and ensure high stability of the final hybrid device. The control of both the thickness of the PMMA shell and the concentration of the dopant dyes allow for fine tuning of the emission color of the LUCO LED and to obtain white light with CIE chromatic coordinates x = 0.32 and y = 0.33, with rendering index as high as 80. This simple and versatile procedure is not dye-exclusive and is therefore extendable to other molecular systems for color-tunable efficient solid-state lighting sources.

  15. Straightforward fabrication of stable white LEDs by embedding of inorganic UV-LEDs into bulk polymerized polymethyl-methacrylate doped with organic dyes

    Science.gov (United States)

    Di Martino, Daniela; Beverina, Luca; Sassi, Mauro; Brovelli, Sergio; Tubino, Riccardo; Meinardi, Francesco

    2014-01-01

    Stable white-emitting down-converted LEDs are straightforwardly prepared by bulk polymerization of an organic dye doped polymethyl-methacrylate (PMMA) shell directly on top of a highly efficient commercial blue-emitting InGaN LED. Our optimized polymerization procedure allows for extending the form factor of achievable luminescence converter (LUCO) material beyond the conventional thin film form and to directly produce devices with light bulb design. The selected organic dyes, the blue-emitting Coumarin 30 and a red-emitting diketopyrrolopyrrole derivative, exhibit high compatibility with the free radical polymerization reaction of the PMMA matrix and ensure high stability of the final hybrid device. The control of both the thickness of the PMMA shell and the concentration of the dopant dyes allow for fine tuning of the emission color of the LUCO LED and to obtain white light with CIE chromatic coordinates x = 0.32 and y = 0.33, with rendering index as high as 80. This simple and versatile procedure is not dye-exclusive and is therefore extendable to other molecular systems for color-tunable efficient solid-state lighting sources. PMID:24638041

  16. Preparation of Organic-Inorganic Hybrid Nanocapsules by Interfacial Miniemulsion Polymerization%界面细乳液聚合制备有机-无机杂化纳米胶囊

    Institute of Scientific and Technical Information of China (English)

    许仙波; 尚玥; 单国荣

    2015-01-01

    3-Methacryloxypropyltrimethoxysilane (MPS) was introduced into the styrene miniemulsion polymerization templated by low molecular weight hydrocarbon to prepare organic-inorganic hybrid nanocapsules. The hydrophilicity of the MPS hydrolysates and the hydrolysis-condensation reactions of MPS led to the interfacial polymerization and radicals anchored at the interface of latex and water. The organic-inorganic hybrid nanocapsules were only obtained with MPS, but the capsulation fraction was low. In order to increase the induction and anchorage functions of MPS to increase the capsulate fractions, N-isopropylacrylamide (NIPAM) and divinylbenzene (DVB) were introduced into the polymerization system. The effects of NIPAM and DVB amounts on the morphology of nanocapsules were discussed. The nanocapsule morphology was also determined by emulsifier concentration and the amount of small molecular weight hydrocarbon.%将甲基丙烯酸3-三甲氧基硅丙酯(MPS)引入以小分子烃为模板的苯乙烯细乳液聚合中,制备有机-无机杂化纳米胶囊。MPS由于其水解产物的亲水性及能够水解-缩合反应的特性使得MPS能够同时起界面聚合诱导剂和自由基锚定剂的作用,制备有机-无机杂化纳米胶囊,但囊化率不高。为了强化 MPS 的诱导和锚定作用,向体系中进一步加入N-异丙基丙烯酰胺(NIPAM)、二乙烯基苯(DVB),可以得到囊化率更高的产品。详细讨论了NIPAM、DVB用量对有机-无机杂化纳米胶囊形态的影响。乳化剂用量以及小分子烃模板含量也是影响胶囊形态的重要因素。

  17. Evaluation of Thermal Control Coatings and Polymeric Materials Exposed to Ground Simulated Atomic Oxygen and Vacuum Ultraviolet Radiation

    Science.gov (United States)

    Kamenetzky, R. R.; Vaughn, J. A.; Finckenor, M. M.; Linton, R. C.

    1995-01-01

    Numerous thermal control and polymeric samples with potential International Space Station applications were evaluated for atomic oxygen and vacuum ultraviolet radiation effects in the Princeton Plasma Physics Laboratory 5 eV Neutral Atomic Oxygen Facility and in the MSFC Atomic Oxygen Drift Tube System. Included in this study were samples of various anodized aluminum samples, ceramic paints, polymeric materials, and beta cloth, a Teflon-impregnated fiberglass cloth. Aluminum anodizations tested were black duranodic, chromic acid anodize, and sulfuric acid anodize. Paint samples consisted of an inorganic glassy black paint and Z-93 white paint made with the original PS7 binder and the new K2130 binder. Polymeric samples evaluated included bulk Halar, bulk PEEK, and silverized FEP Teflon. Aluminized and nonaluminized Chemfab 250 beta cloth were also exposed. Samples were evaluated for changes in mass, thickness, solar absorptance, and infrared emittance. In addition to material effects, an investigation was made comparing diffuse reflectance/solar absorptance measurements made using a Beckman DK2 spectroreflectometer and like measurements made using an AZ Technology-developed laboratory portable spectroreflectometer.

  18. Interaction nonlinearity in asphalt binders

    Science.gov (United States)

    Motamed, Arash; Bhasin, Amit; Liechti, Kenneth M.

    2012-05-01

    Asphalt mixtures are complex composites that comprise aggregate, asphalt binder, and air. Several research studies have shown that the mechanical behavior of the asphalt mixture is strongly influenced by the matrix, i.e. the asphalt binder. Characterization and a thorough understanding of the binder behavior is the first and crucial step towards developing an accurate constitutive model for the composite. Accurate constitutive models for the constituent materials are critical to ensure accurate performance predictions at a material and structural level using micromechanics. This paper presents the findings from a systematic investigation into the nature of the linear and nonlinear response of asphalt binders subjected to different types of loading using the Dynamic Shear Rheometer (DSR). Laboratory test data show that a compressive normal force is generated in an axially constrained specimen subjected to torsional shear. This paper investigates the source of this normal force and demonstrates that the asphalt binder can dilate when subjected to shear loads. This paper also presents the findings from a study conducted to investigate the source of the nonlinearity in the asphalt binder. Test results demonstrate that the application of cyclic shear loads results in the development of a normal force and a concomitant reduction in the dynamic shear modulus. This form of nonlinear response is referred to as an "interaction nonlinearity". A combination of experimental and analytical tools is used to demonstrate and verify the presence of this interaction nonlinearity in asphalt binders. The findings from this study highlight the importance of modeling the mechanical behavior of asphalt binders based on the overall stress state of the material.

  19. Cobaltocenium-containing block copolymers: ring-opening metathesis polymerization, self-assembly and precursors for template synthesis of inorganic nanoparticles.

    Science.gov (United States)

    Ren, Lixia; Zhang, Jiuyang; Hardy, Christopher G; Ma, Shuguo; Tang, Chuanbing

    2012-04-13

    Side-chain cobaltocenium-containing block copolymers are prepared by ring-opening metathesis polymerization (ROMP). These block copolymers include one cobaltocenium-containing block, with the second block being either a nonmetal-containing segment or a cobaltocenium-containing segment with different counterions. These block copolymers are self-assembled into spherical core/shell micelles in solutions. A template strategy is used to prepare cobalt (II or III)-containing nanoparticles by treating the self-assembled micelles via UV/ozonolysis and pyrolysis. Characterization by X-ray photon spectroscopy and X-ray diffraction indicates that these nanoparticles consist of different oxidants of cobalt, depending on the chemical compositions of block copolymers. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Analysis of metal cations and inorganic anions in olive oil mill waste waters by atomic absorption spectroscopy and ion chromatography. Detection of metals bound mainly to the organic polymeric fraction.

    Science.gov (United States)

    Arienzo, M; Capasso, R

    2000-04-01

    Metal cations were quantitatively detected by atomic absorption spectrometry in samples of olive oil mill waste waters obtained by a pressure process (omww(1)) (K, 17.1; Mg, 2.72; Ca, 2.24; Na, 0.40; Fe, 0.123; Zn, 0.0630; Mn, 0.0147; Cu, 0.00860 g L(-)(1)) and a centrifugation process (omww(2)) (K, 9.80; Mg, 1.65; Ca, 1.35; Na, 0. 162; Fe, 0.0330; Zn, 0.0301; Mn, 0.00910; Cu, 0.00980 g L(-)(1)). The inorganic anions, determined in the same samples by ion chromatography, proved to be Cl(-), H(2)PO(4)(-), F(-), SO(4)(2)(-), and NO(3)(-) (1.61, 1.05, 0.66, 0.52, and 0.023 g L(-)(1), respectively, in omww(1) and 0.61, 0.40, 0.25, 0.20, and 0.0090 g L(-)(1), respectively, in omww(2)). Most of the metal cations were revealed to be bound to the omww organic polymeric fraction (opf), composed of polysaccharides, phenol polymers, and proteins. Opf relative molecular weight was substantially estimated in the range between 1000 and 30000 Da for approximately 75% and in the range from 30000 to 100000 Da for approximately 25%. The free residual cations pool proved to be neutralized by the inorganic counteranions. Finally, the possible exploitation of this material in agriculture and in environmental biotechnology processes is also discussed in the light of its chemical and biochemical oxygen demand parameters.

  1. Increase in composite binder activity

    Science.gov (United States)

    Fediuk, R.; Smoliakov, A.; Stoyushko, N.

    2016-11-01

    The binder of portland cement (51-59 wt.%), fly ash of thermal power stations (3644 wt.%), limestone crushing waste (4-9 wt.%) and dry hyper plasticizer (0.2 wt.%) has been created. It can be used in the building materials industry for production of high-strength concrete. The composite binder is obtained by co-milling of the components in vario-planetary mill to a specific surface area of 550-600 m2/kg. The technical result is the possibility of obtaining a composite binder with significant replacement of cement with industrial waste, cost-effective and superior to portland cement for construction and technical properties, increased activity. This allows producing concrete for walling with a compressive strength of 100 MPa, while using more than 50% of industrial waste.

  2. Electrochemical components employing polysiloxane-derived binders

    Science.gov (United States)

    Delnick, Frank M.

    2013-06-11

    A processed polysiloxane resin binder for use in electrochemical components and the method for fabricating components with the binder. The binder comprises processed polysiloxane resin that is partially oxidized and retains some of its methyl groups following partial oxidation. The binder is suitable for use in electrodes of various types, separators in electrochemical devices, primary lithium batteries, electrolytic capacitors, electrochemical capacitors, fuel cells and sensors.

  3. The Influence of Wall Binders

    DEFF Research Database (Denmark)

    Rose, Jørgen

    1997-01-01

    This report is an analysis of the thermal bridge effects that occur in wall binders in masonry buildings. The effects are analyzed using a numerical calculation programme.The results are compared to the values given in the danish standard, DS418....

  4. Unprecedented {sup 1}/{sub {infinity}}[{beta}-Mo{sub 8}O{sub 26}]{sup 4-} polymeric chains and four novel organic-inorganic hybrids based on Mo-POMs and azaheterocycles templates

    Energy Technology Data Exchange (ETDEWEB)

    Du Haijuan; Zunzhe Shu [College of Chemistry and Molecular Engineering, Zhengzhou University, Zhengzhou 450001 (China); Niu Yunyin, E-mail: niuyy@zzu.edu.cn [College of Chemistry and Molecular Engineering, Zhengzhou University, Zhengzhou 450001 (China); Song Lisha; Zhu Yu [College of Chemistry and Molecular Engineering, Zhengzhou University, Zhengzhou 450001 (China)

    2012-06-15

    Abstrct: Four novel organic-inorganic hybrid materials based on Mo-POMs and organic templates, namely [DEB] [{beta}-Mo{sub 8}O{sub 26}] [NH{sub 4}]{sub 2} (1), [BMIM] [{beta}-Mo{sub 8}O{sub 26}]{sub 0.5}{center_dot}H{sub 2}O (2), [BMIM] [1D-Mo{sub 8}O{sub 26}]{sub 0.5} (3) and {l_brace}3D-[Cu(DIE){sub 2}] [1D-Mo{sub 8}O{sub 26}]{sub 0.5}{r_brace}{sub {infinity}} (4) [DEB= 1,1 Prime -diethyl-4,4 Prime -bipyridinium, BMIM=1,1 Prime -bis(1-methylimidazolium)methylene, DIE=1,2-diimidazoloethane] have been hydrothermally synthesized and characterized by elemental analyses, IR spectroscopy, thermal gravimetric analysis(TGA) and single-crystal X-ray diffraction. Both compounds 1 and 2 are POMs-based supramolecular compounds consisted of independent [{beta}-Mo{sub 8}O{sub 26}]{sup 4-} anions and [DEB]{sup 2+} or [BMIM]{sup 2+} organic cations. Compound 3 is the first external template example of Mo-POMs-based supramolecular network incorporated with novel {sup 1}/{sub {infinity}}[{beta}-Mo{sub 8}O{sub 26}]{sup 4-} polymeric chains. Compound 4 is a rare supramolecular structure that contains octamolybdate {sup 1}/{sub {infinity}}[{beta}-Mo{sub 8}O{sub 26}]{sup 4-} polymeric chains interconnected via DIE ligands to form a 3D net. Moreover, it was indicated that these polyacid compounds had definite catalytic activities on the probe reaction of acetaldehyde oxidation to acetic acid with H{sub 2}O{sub 2}. - Graphical abstract: Four novel organic templated polyoxometalates comprising of 0D, 1D and 3D supramolecular frameworks together with the catalytic activities on the acetaldehyde oxidation to acetic acid were reported. Highlights: Using cation templated self-assembly four novel polyoxometalates were prepared. Compounds 1 and 2 consisted of independent [{beta}-Mo{sub 8}O{sub 26}]{sup 4-} anions and organic cations. Compound 3 is the first external template-assisted POMs with {sup 1}/{sub {infinity}}[{beta}-Mo{sub 8}O{sub 26}]{sup 4-} chain. Compound 4 is a rare 3D net

  5. Polymeric Binders which Reversibly Dissociate at Elevated Temperatures

    Science.gov (United States)

    1978-05-01

    materials must be used which are capable of regenerating the free isocyana.e on heating and will not undergo undesirable side reactions . The most widely...such as imidazole, indazole and benzotriazole, exhibit a marked tendency to dissociate at temperatures as low as 80*C to 100*C. With 4,5...only undergo a Diels-Alder reaction at room temperature with a variety of dienes, but it will also react with other functional groups. Many of these

  6. Preparation and characterization of RuO2/polyaniline/polymer binder composite electrodes for supercapacitor applications

    Directory of Open Access Journals (Sweden)

    SUZANA SOPČIĆ

    2012-03-01

    Full Text Available The composite electrodes consisting of amorphous and hydrous RuO2, polyaniline and polymeric binder, Nafion® or poly(vinilydene fluoride were prepared. The electro¬chem-ical and pseudocapacitive properties of the prepared electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The results show that the responses of composite electrodes are very sensitive to the presence of individual components and their respective ratio in the mixture. The difference in the electro-chemical behavior was explained by the different physico-chemical properties of the polymeric binders.

  7. Investigation of film solidification and binder migration during drying of Li-Ion battery anodes

    Science.gov (United States)

    Jaiser, Stefan; Müller, Marcus; Baunach, Michael; Bauer, Werner; Scharfer, Philip; Schabel, Wilhelm

    2016-06-01

    The property determining micro-structure of battery electrodes essentially evolves during drying, appointing it a paramount, yet insufficiently understood processing step in cell manufacturing. The distribution of functional additives such as binder or carbon black throughout the film strongly depends on the drying process. A representative state-of-the-art model system comprising graphite, polymeric binder, carbon black and solvent is investigated to gain an insight into the underlying processes. A new experimental approach is introduced that allows for revelation of the evolution of binder concentration gradients throughout the film during drying. Binder is detected by means of energy-dispersive x-ray spectroscopy (EDS) at the top and bottom surface. Drying kinetics is investigated and the impact of the drying process on electrochemical performance is disclosed. The enrichment of binder at the surface, which is observed while applying high drying rates, is shown to depend on two fundamental processes, namely capillary action and diffusion. The findings reveal characteristic drying stages that provide fundamental insights into film solidification. Based on that, a top-down consolidation mechanism capable of explaining the experimental findings is disclosed. Adhesion of the active layer to the substrate is shown to strongly depend on the local binder concentration in the vicinity of the substrate.

  8. An improved sodium silicate binder modified by ultra-fine powder materials

    Institute of Scientific and Technical Information of China (English)

    WANG Ji-na; FAN Zi-tian; WANG Hua-fang; DONG Xuan-pu; HUANG Nai-yu

    2007-01-01

    This paper presents a new method of modifying sodium silicate binder with ultra-fine powders. The sodium silicate binder modified by ultra-fine powder A and the organic B can reduce the addition amount of the binder. The results indicate that the 24 h strength has increased by 39.9% at room temperature and the residual strength has decreased by 30.7% at 800℃, compared to the conventional sodium silicate. An available material to improve the moisture resistance was also found by adding about 2% more inorganic C, and it can increase the moist strength by 20%. In the end, the microanalyses are given to explain the modifying machanism, i. e., the ultra-fine powder A can refine the sodium silicate binder to avoid holes in the binder bond, which can increase the 24 h strength at room temperture, and can lead to more cracks in the bond after the molding sand is heated to 800℃. This is because of the stress caused by the new eutectic complex of modified sodium silicate binder.

  9. Azidated Ether-Butadiene-Ether Block Copolymers as Binders for Solid Propellants

    Science.gov (United States)

    Cappello, Miriam; Lamia, Pietro; Mura, Claudio; Polacco, Giovanni; Filippi, Sara

    2016-07-01

    Polymeric binders for solid propellants are usually based on hydroxyl-terminated polybutadiene (HTPB), which does not contribute to the overall energy output. Azidic polyethers represent an interesting alternative but may have poorer mechanical properties. Polybutadiene-polyether copolymers may combine the advantages of both. Four different ether-butadiene-ether triblock copolymers were prepared and azidated starting from halogenated and/or tosylated monomers using HTPB as initiator. The presence of the butadiene block complicates the azidation step and reduces the storage stability of the azidic polymer. Nevertheless, the procedure allows modifying the binder properties by varying the type and lengths of the energetic blocks.

  10. Observation of asphalt binder microstructure with ESEM.

    Science.gov (United States)

    Mikhailenko, P; Kadhim, H; Baaj, H; Tighe, S

    2017-09-01

    The observation of asphalt binder with the environmental scanning electron microscope (ESEM) has shown the potential to observe asphalt binder microstructure and its evolution with binder aging. A procedure for the induction and identification of the microstructure in asphalt binder was established in this study and included sample preparation and observation parameters. A suitable heat-sampling asphalt binder sample preparation method was determined for the test and several stainless steel and Teflon sample moulds developed, finding that stainless steel was the preferable material. The magnification and ESEM settings conducive to observing the 3D microstructure were determined through a number of observations to be 1000×, although other magnifications could be considered. Both straight run binder (PG 58-28) and an air blown oxidised binder were analysed; their structures being compared for their relative size, abundance and other characteristics, showing a clear evolution in the fibril microstructure. The microstructure took longer to appear for the oxidised binder. It was confirmed that the fibril microstructure corresponded to actual characteristics in the asphalt binder. Additionally, a 'bee' micelle structure was found as a transitional structure in ESEM observation. The test methods in this study will be used for more comprehensive analysis of asphalt binder microstructure. © 2017 The Authors Journal of Microscopy © 2017 Royal Microscopical Society.

  11. Twin screw wet granulation: Binder delivery.

    Science.gov (United States)

    Saleh, Mohammed F; Dhenge, Ranjit M; Cartwright, James J; Hounslow, Michael J; Salman, Agba D

    2015-06-20

    The effects of three ways of binder delivery into the twin screw granulator (TSG) on the residence time, torque, properties of granules (size, shape, strength) and binder distribution were studied. The binder distribution was visualised through the transparent barrel using high speed imaging as well as quantified using offline technique. Furthermore, the effect of binder delivery and the change of screw configuration (conveying elements only and conveying elements with kneading elements) on the surface velocity of granules across the screw channel were investigated using particle image velocimetry (PIV). The binder was delivered in three ways; all solid binder incorporated with powder mixture, 50% of solid binder mixed with powder mixture and 50% mixed with water, all the solid binder dissolved in water. Incorporation of all solid binder with powder mixture resulted in the relatively longer residence time and higher torque, narrower granule size distribution, more spherical granules, weaker big-sized granules, stronger small-sized granules and better binder distribution compared to that in other two ways. The surface velocity of granules showed variation from one screw to another as a result of uneven liquid distribution as well as shown a reduction while introducing the kneading elements into the screw configuration.

  12. Polymeric microspheres

    Science.gov (United States)

    Walt, David R.; Mandal, Tarun K.; Fleming, Michael S.

    2004-04-13

    The invention features core-shell microsphere compositions, hollow polymeric microspheres, and methods for making the microspheres. The microspheres are characterized as having a polymeric shell with consistent shell thickness.

  13. Bitumen modifiers for reduced temperature asphalts: a comparative analysis between three polymeric and non-polymeric additives

    OpenAIRE

    Cuadri Vega, Antonio Abad; Carrera Páez, Virginia; Izquierdo Rodríguez, María Angeles; García Morales, Moisés; Navarro Domínguez, Francisco Javier

    2014-01-01

    This study presents three bitumen modifiers which may find successful application in the fabrication of binders for warm mix asphalt in the paving industry. In that sense, two non-polymeric additives, thiourea and thiourea dioxide, along with a reactive isocyanate-terminated prepolymer have been evaluated. Viscous flow and linear viscoelasticity tests, at 60 ºC, reveal bituminous modified binders which evolve towards highly viscous materials when subjected to ambient curing. However, at 135 º...

  14. Bitumen modifiers for reduced temperature asphalts: a comparative analysis between three polymeric and non-polymeric additives

    OpenAIRE

    Cuadri Vega, Antonio Abad; Carrera Páez, Virginia; Izquierdo Rodríguez, María Angeles; García Morales, Moisés; Navarro Domínguez, Francisco Javier

    2014-01-01

    This study presents three bitumen modifiers which may find successful application in the fabrication of binders for warm mix asphalt in the paving industry. In that sense, two non-polymeric additives, thiourea and thiourea dioxide, along with a reactive isocyanate-terminated prepolymer have been evaluated. Viscous flow and linear viscoelasticity tests, at 60 ºC, reveal bituminous modified binders which evolve towards highly viscous materials when subjected to ambient curing. However, at 135 º...

  15. Time dependent viscoelastic rheological response of pure, modified and synthetic bituminous binders

    Science.gov (United States)

    Airey, G. D.; Grenfell, J. R. A.; Apeagyei, A.; Subhy, A.; Lo Presti, D.

    2016-08-01

    Bitumen is a viscoelastic material that exhibits both elastic and viscous components of response and displays both a temperature and time dependent relationship between applied stresses and resultant strains. In addition, as bitumen is responsible for the viscoelastic behaviour of all bituminous materials, it plays a dominant role in defining many of the aspects of asphalt road performance, such as strength and stiffness, permanent deformation and cracking. Although conventional bituminous materials perform satisfactorily in most highway pavement applications, there are situations that require the modification of the binder to enhance the properties of existing asphalt material. The best known form of modification is by means of polymer modification, traditionally used to improve the temperature and time susceptibility of bitumen. Tyre rubber modification is another form using recycled crumb tyre rubber to alter the properties of conventional bitumen. In addition, alternative binders (synthetic polymeric binders as well as renewable, environmental-friendly bio-binders) have entered the bitumen market over the last few years due to concerns over the continued availability of bitumen from current crudes and refinery processes. This paper provides a detailed rheological assessment, under both temperature and time regimes, of a range of conventional, modified and alternative binders in terms of the materials dynamic (oscillatory) viscoelastic response. The rheological results show the improved viscoelastic properties of polymer- and rubber-modified binders in terms of increased complex shear modulus and elastic response, particularly at high temperatures and low frequencies. The synthetic binders were found to demonstrate complex rheological behaviour relative to that seen for conventional bituminous binders.

  16. UV-Irradiation Cured Organic-inorganic Hybrid Nanocomposite Initiated by Ethoxysilane-modified Multifunctional Polymeric Photoinitiator through Sol-gel Process%UV-Irradiation Cured Organic-inorganic Hybrid Nanocomposite Initiated by Ethoxysilane-modified Multifunctional Polymeric Photoinitiator through Sol-gel Process

    Institute of Scientific and Technical Information of China (English)

    Hu, Lihua; Shi, Wenfang

    2011-01-01

    The UV-cured organic-inorganic hybrid nanocomposite (nano-Si-m-PI) was prepared through the photopolymeri- zation of acrylic resin initiated by ethoxysilane-modified multifunctional oligomeric photoinitiator (Si-m-PI). The es- terification reaction of 2-hydroxy-4'-(2-hydroxyethoxy)-2-methylpropiophenone (Irgacure 2959) with thioglycolic acid, and the following addition reactions with dipentaerythritol hexaacrylate and then 3-aminopropyltriethoxysilane were carried out for preparing the Si-m-PI. The Si-m-PI exhibits the similar UV absorption and molar extinction coefficient with Irgacure 2959. The photoinitiating activity study by photo-DSC analysis showed that the Si-m-PI possesses high photopolymerization rate at the peak maximum (Rpax) and final unsaturation conversion (Pf) in the cured hybrid films. From the scanning electron microscope (SEM) observation, the SiO2 nanoparticles dispersed uniformly in the formed nano-Si-m-PI, whereas the aggregation of nanoparticals occurred in nano-Irg, which was prepared through the photopolymerization of acrylic resin initiated by Irgacure 2959. Moreover, compared with the UV-cured pure polymer and nano-Irg, the nano-Si-m-PI showed remarkably enhanced thermal stability and mechanical properties.

  17. Potential of the application of the modified polysaccharides water solutions as binders of moulding sands

    Directory of Open Access Journals (Sweden)

    K. Kaczmarska

    2015-10-01

    Full Text Available The results of preliminary tests of selected properties of the moulding sands with the binder in the form of a 5 % water solution of the sodium salt of carboxymethyl starch (with a degree of substitution (DS of 0,2 and 0,87 arepresented in this study. The moulding sand properties such as permeability, abrasion resistance, tensile and bendingstrength - after curing - are shown in series of tests. The cure process was conducted in a field of electromagnetic radiation within the microwave range. The effect of the microwave treatment on the moulding sand was evaporating of water (solvent in a binder and cross-linking of the polymeric binder. As a result the cured moulding sands with particular properties, essential in the context of its application in the mould technology in the foundry industry, were obtained.

  18. Water-resistant gypsum binder

    Directory of Open Access Journals (Sweden)

    Panchenko Alexander I.

    2016-01-01

    Full Text Available The authors developed a multi-component gypsum binder (MGB with an improved (by 1.8 to 2.2 times water resistance value in comparison with the initial gypsum and a softening factor value within the range of 0.85 to 0.91 through the introduction of a complex additive containing carbide mud and bio-silica. The use of a complex additive provides for the formation of a denser structure due to the formation of low-base calcium hydrated silicates at early stages of the hardening process under wet or dry air conditions. The developed binding agent has a lower (by 2.5 to 3 times open porosity, a greater compressive strength (by 1.4 to 1.6 times for a dry state and by 2.6 times in a water-saturated state and does not require any special curing conditions in contrast to the other multi-component gypsum binders. The authors show the influence of mud-and-silica additive on the properties of hardened MGB and suggest a method of computation of the optimum MGB composition for given components.

  19. On the microstructure of bituminous binders

    NARCIS (Netherlands)

    Fischer, H.R.; Dillingh, E.C.; Hermse, C.G.M.

    2014-01-01

    The objective of this work is to study the common features and the evolution of microstructures of bituminous binders regardless of their grade (PEN 10/20 to 160/220) and source/origin using the atomic force microscope operated in phase contrast mode. All bituminous binders show the same microstruct

  20. Rheological characteristics of aged asphalt binder

    Institute of Scientific and Technical Information of China (English)

    刘聪慧; 吴少鹏; 刘全涛; 朱国军

    2008-01-01

    Different aging levels(RTFOT,PAV-10h,PAV-20h and PAV-30 h) of asphalt binders with various mass ratios of mineral powder to asphalt(0,0.4,0.8,1.2,1.6,2.0) were used to investigate the rheological properties of aged asphalt binders with respect to their short and long terms aging characteristics.Viscosity test,dynamic shear test and creep test were conducted.The test results indicate that the viscosity of aged asphalt binder increases sharply with the extension of aging period.Complex shear modulus of aged asphalt increases,which indicates that the stiffness of asphalt binders can increase.The phase angle for aged asphalt binders reduces,which indicates that the elastic portion for viscoelastic property of asphalt binders increases.|G*|·sin δ increases after aging procedure which means that the fatigue resistance becomes poor.The creep test results show that creep strain curves varies remarkably for virgin and aged asphalt binders.The total strain during loading period and the permanent strain decreases significantly for aged asphalt binders,which implies that the elastic portion increases and the viscous portion decreases.

  1. Guar gum: Structural and electrochemical characterization of natural polymer based binder for silicon-carbon composite rechargeable Li-ion battery anodes

    Science.gov (United States)

    Kuruba, Ramalinga; Datta, Moni Kanchan; Damodaran, Krishnan; Jampani, Prashanth H.; Gattu, Bharat; Patel, Prasad P.; Shanthi, Pavithra M.; Damle, Sameer; Kumta, Prashant N.

    2015-12-01

    Long term cyclability of a composite Li-ion anode electrode comprised of 82 wt.% Si/C lithium ion active material along with 8 wt.% polymeric binder and 10 wt.% Super P conductive carbon black has been studied utilizing polymeric binders exhibiting different elastic/tensile moduli and tensile yield strengths. Accordingly, electrochemically active Si/C composite synthesized by high energy mechanical milling (HEMM), exhibiting reversible specific capacities of ∼780 mAh/g and ∼600 mAh/g at charge/discharge rates of ∼50 mA/g and ∼200 mA/g, respectively were selected as the Li-ion active anode. Polyvinylidene fluoride (PVDF) and purified guar gum (PGG) with reported elastic moduli ∼1000 MPa and ∼3200 MPa, respectively were selected as the binders. Results show that the composite electrode (Si/C + binder + conducting carbon) comprising the higher elastic modulus binder (PGG) exhibits better long term cyclability contrasted with PVDF. 1H-NMR analysis of the polymer before and after cycling shows structural degradation/deformation of the low elastic modulus PVDF, whereas the high elastic modulus PGG binder shows no permanent structural deformation or damage. The results presented herein thus suggest that PGG based polymers exhibiting high elastic modulus are a promising class of binders with the desired mechanical integrity needed for enduring the colossal volume expansion stresses of Si/C based composite anodes.

  2. INFLUENCE OF POLYMERIC ADDITIVES ON CRYSTALLIZATION OF CALCIUM SULPHATE DIHYDRATE

    OpenAIRE

    Ustinova Yulia Valer’evna

    2013-01-01

    Currently, functional additives are widely spread in the production of inorganic dry mixtures. However, their impact on the microstructure of products, generated in the process of hardening of inorganic binders, is understudied. In this context, the goal of the work is the study of calcium sulfate dihydrate (CaSO •2H O) crystallization. Super plasticizer based on sulfonated melamine-formaldehyde resin, methylcellulose and vinyl acetate, ethylene and vinyl chloride copolymer powder were select...

  3. Optimization of Binder Jetting Using Taguchi Method

    Science.gov (United States)

    Shrestha, Sanjay; Manogharan, Guha

    2017-03-01

    Among several additive manufacturing (AM) methods, binder-jetting has undergone a recent advancement in its ability to process metal powders through selective deposition of binders on a powder bed followed by curing, sintering, and infiltration. This study analyzes the impact of various process parameters in binder jetting on mechanical properties of sintered AM metal parts. The Taguchi optimization method has been employed to determine the optimum AM parameters to improve transverse rupture strength (TRS), specifically: binder saturation, layer thickness, roll speed, and feed-to-powder ratio. The effects of the selected process parameters on the TRS performance of sintered SS 316L samples are studied with the American Society of Testing Materials (ASTM) standard test method. It was found that binder saturation and feed-to-powder ratio were the most critical parameters, which reflects the strong influence of binder powder interaction and density of powder bed on resulting mechanical properties. This article serves as an aid in understanding the optimum process parameters for binder jetting of SS 316L.

  4. Optimization of Binder Jetting Using Taguchi Method

    Science.gov (United States)

    Shrestha, Sanjay; Manogharan, Guha

    2017-01-01

    Among several additive manufacturing (AM) methods, binder-jetting has undergone a recent advancement in its ability to process metal powders through selective deposition of binders on a powder bed followed by curing, sintering, and infiltration. This study analyzes the impact of various process parameters in binder jetting on mechanical properties of sintered AM metal parts. The Taguchi optimization method has been employed to determine the optimum AM parameters to improve transverse rupture strength (TRS), specifically: binder saturation, layer thickness, roll speed, and feed-to-powder ratio. The effects of the selected process parameters on the TRS performance of sintered SS 316L samples are studied with the American Society of Testing Materials (ASTM) standard test method. It was found that binder saturation and feed-to-powder ratio were the most critical parameters, which reflects the strong influence of binder powder interaction and density of powder bed on resulting mechanical properties. This article serves as an aid in understanding the optimum process parameters for binder jetting of SS 316L.

  5. Interpenetrating Polymer Networks as Binders for Solid Composite Propellants

    Directory of Open Access Journals (Sweden)

    S. Parthiban

    1992-07-01

    Full Text Available A new family of polymeric binders for solid composite propellants is proposed, based on two component interpenetrating polymer networks (IPNs. These networks comprise two different polyurethanes based on hydroxy terminated polybutadiene and ISRO polyol interpenetrated with two different vinyl polymers, viz poly methyl methacrylate and polystyrene. the networks synthesized by the simultaneous interpenetrating technique have been characterized for their properties, such as stress-strain, density, viscosity, thermal degradation, and heat of combustion. Phase morphologies have been determined using electron microscopy. Suitable explanations have been adduced to rationalize the properties of IPNs in terms of their structures and chain interactions. A study of the mechanical properties and burning rates of the ammonium perchlorate (AP-based solid propellant using the newly synthesised IPNs as binders, has been carried out. The results show that both mechanical strength and burning rate of solid propellants could be suitably modified by simply changing the nature and/or the ratio of the two interpenetrating polymer components.

  6. Thermal Degradation Studies of A Polyurethane Propellant Binder

    Energy Technology Data Exchange (ETDEWEB)

    Assink, R.A.; Celina, M.; Gillen, K.T.; Graham, A.C.; Minier, L.M.

    1999-06-12

    The thermal oxidative aging of a crosslinked hydroxy-terminated polybutadiene (HTPB)/isophorone diisocyanate (IPDI) based polyurethane rubber, used as a polymeric binder in solid propellant grain, was investigated at temperatures from 25 C to 125 C. The changes in tensile elongation, polymer network properties and chain dynamics, mechanical hardening and density were determined with a range of techniques including modulus profiling, solvent swelling, NMR relaxation and O{sub 2} permeability measurements. We critically evaluated the Arrhenius methodology that is commonly used with a linear extrapolation of high temperature aging data using extensive data superposition and highly sensitive oxygen consumption experiments. The effects of other constituents in the propellant formulation on aging were also investigated. We conclude that crosslinking is the dominant process at higher temperatures and that the degradation involves only limited hardening in the bulk of the material. Significant curvature in the Arrhenius diagram of the oxidation rates was observed. This is similar to results for other rubber materials.

  7. Thermal Degradation Studies of A Polyurethane Propellant Binder

    Energy Technology Data Exchange (ETDEWEB)

    Assink, R.A.; Celina, M.; Gillen, K.T.; Graham, A.C.; Minier, L.M.

    1999-06-12

    The thermal oxidative aging of a crosslinked hydroxy-terminated polybutadiene (HTPB)/isophorone diisocyanate (IPDI) based polyurethane rubber, used as a polymeric binder in solid propellant grain, was investigated at temperatures from 25 C to 125 C. The changes in tensile elongation, polymer network properties and chain dynamics, mechanical hardening and density were determined with a range of techniques including modulus profiling, solvent swelling, NMR relaxation and O{sub 2} permeability measurements. We critically evaluated the Arrhenius methodology that is commonly used with a linear extrapolation of high temperature aging data using extensive data superposition and highly sensitive oxygen consumption experiments. The effects of other constituents in the propellant formulation on aging were also investigated. We conclude that crosslinking is the dominant process at higher temperatures and that the degradation involves only limited hardening in the bulk of the material. Significant curvature in the Arrhenius diagram of the oxidation rates was observed. This is similar to results for other rubber materials.

  8. Center for BioBased Binders and Pollution Reduction Technology

    Energy Technology Data Exchange (ETDEWEB)

    Thiel, Jerry [Univ. of Northern Iowa, Cedar Falls, IA (United States)

    2013-07-01

    Funding will support the continuation of the Center for Advanced Bio-based Binders and Pollution Reduction Technology Center (CABB) in the development of bio-based polymers and emission reduction technologies for the metal casting industry. Since the formation of the center several new polymers based on agricultural materials have been developed. These new materials have show decreases in hazardous air pollutants, phenol and formaldehyde as much as 50 to 80% respectively. The polymers termed bio-polymers show a great potential to utilize current renewable agricultural resources to replace petroleum based products and reduce our dependence on importing of foreign oil. The agricultural technology has shown drastic reductions in the emission of hazardous air pollutants and volatile organic compounds and requires further development to maintain competitive costs and productivity. The project will also research new and improved inorganic binders that promise to eliminate hazardous emissions from foundry casting operations and allow for the beneficial reuse of the materials and avoiding the burdening of overcrowded landfills.

  9. The absorption of polymeric composites

    Science.gov (United States)

    Řídký, R.; Popovič, M.; Rolc, S.; Drdlová, M.; Krátký, J.

    2016-06-01

    An absorption capacity of soft, viscoelastic materials at high strain rates is important for wide range of practical applications. Nowadays there are many variants of numerical models suitable for this kind of analysis. The main difficulty is in selection of the most realistic numerical model and a correct setup of many unknown material constants. Cooperation between theoretical simulations and real testing is next crucial point in the investigation process. Standard open source material database offer material properties valid for strain rates less than 250 s-1. There are experiments suitable for analysis of material properties with strain rates close to 2000 s-1. The high strain-rate characteristics of a specific porous blast energy absorbing material measured by modified Split Hopkinson Pressure Bar apparatus is presented in this study. Testing these low impedance materials using a metallic split Hopkinson pressure bar setup results in poor signal to noise ratios due to impedance mismatching. These difficulties are overcome by using polymeric Hopkinson bars. Conventional Hopkinson bar analysis cannot be used on the polymeric bars due to the viscoelastic nature of the bar material. One of the possible solution leads to complex and frequency depended Young modulus of testing bars material. This testing technique was applied to materials composed of porous glass/ceramic filler and polymeric binder, with density of 125 - 300 kg/m3 and particle size in range of 50 µm - 2 mm. The achieved material model was verified in practical application of sandwich structure includes polymeric composites under a blast test.

  10. Aqueous SARA ATRP using Inorganic Sulfites.

    Science.gov (United States)

    Abreu, Carlos M R; Fu, Liye; Carmali, Sheiliza; Serra, Arménio C; Matyjaszewski, Krzysztof; Coelho, Jorge F J

    2017-01-14

    Aqueous supplemental activator and reducing agent atom transfer radical polymerization (SARA ATRP) using inorganic sulfites was successfully carried out for the first time. Under optimized conditions, a well-controlled poly[oligo(ethylene oxide) methyl ether acrylate] (POEOA) was obtained with sulfites (e.g. Na2S2O4) were continuously fed into the reaction mixture. The mechanistic studies proved that these salts can activate alkyl halides directly and regenerate the activator complex. The effects of the feeding rate of the SARA agent (inorganic sulfites), ligand and its concentration, halide salt and its concentration, sulfite used, and copper concentration, were systematically studied to afford fast polymerizations rates while maintaining the control over polymerization. The kinetic data showed linear first-order kinetics, linear evolution of molecular weights with conversion, and polymers with narrow molecular weight distributions (Đ ~1.2) during polymerization even at relatively high monomer conversions (~80%). "One-pot" chain extension and "one-pot" block copolymerization experiments proved the high chain-end functionality. The polymerization could be directly regulated by starting or stopping the continuous feeding of the SARA agent. Under biologically relevant conditions, the aqueous SARA ATRP using inorganic sulfites was used to synthesize a well-defined protein-polymer hybrid by grafting of P(OEOA480) from BSA-O-[iBBr]30.

  11. Polymeric precursors method for obtaining pigments based on Inorganic oxides of chromium and iron deposited on TiO{sub 2}; Metodo dos precursores polimericos para obtencao de pigmentos inorganicos a base de oxidos de cromo e de ferro, depositados sobre TiO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    The case study was the use of chromium oxides and iron, as a precursor in the synthesis of inorganic pigments. The synthesis was based on the dissolution of citric acid as a complexing agent, addition of metal oxides, such as ion chromophores; polymerization with ethylene glycol and doping with titanium oxide. Going through pre-calcination, breakdown, calcination at different temperatures (700, 900 and 1100 deg C resulting in pigments: green for pigment and chromium deposited on TiO2, orange for iron on TiO2. The thermal analysis (TG and DTA), evaluated their thermal decompositions, the XRD revealed the formation of crystalline phases such as iron titanate and chrome titanate; SEM showed the formation of hexagonal particles for both oxides. Under the different analysis, one can see the potential stability of pigments and powders, can be proposed its use as pigments in polymers. (author)

  12. Reclamation of alkaline spent moulding sands of organic and inorganic type and their mixtures

    Directory of Open Access Journals (Sweden)

    R. Dańko

    2011-10-01

    Full Text Available Introduction of modern moulding sands with organic and inorganic binders requires the reclamation treatments in order to be able to reuse the matrices of spent sands. The spent sands, depending on the applied binding agent, are characterised by various abilities of the matrix reclamation. The results of investigations of the reclamation of spent moulding sands with the Rudal binder and spent sands with the Rezolit binder in the system of uniform sands and of mixed ones, are presented in the paper. Investigations were performed by means of the special experimental stands designed and built in the AGH University of Science and Technology, AGH, in Krakow.

  13. Condensation Polymerization

    Indian Academy of Sciences (India)

    S Ramakrishnan

    2017-04-01

    The very idea that large polymer molecules can indeed existwas hotly debated during the early part of the 20th century.As highlighted by Sivaram in his articles on Carothersand Flory, Staudinger’s macromolecular hypothesis was finallyaccepted, and the study of polymers gained momentumbecause of the remarkable efforts of the these two individualswho laid down the foundations concerning the processes thatled to the formation of large polymer molecules, and to thosethat led to an understanding of many of their extraordinaryphysical properties. Condensation polymerizations, as thename suggests, utilizes bond-forming reactions that generatea small molecule condensate, which often needs to be continuouslyremoved to facilitate the formation of the polymer. Inthis article, I shall describe some of the essential principles ofcondensation polymerizations or more appropriately calledstep-growth polymerizations; and I will also describe someinteresting extensions that lead to the formation of polymernetworks and highly branched polymers.

  14. Instrumentation for studying binder burnout in an immobilized plutonium ceramic wasteform

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, M; Pugh, D; Herman, C

    2000-04-21

    The Plutonium Immobilization Program produces a ceramic wasteform that utilizes organic binders. Several techniques and instruments were developed to study binder burnout on full size ceramic samples in a production environment. This approach provides a method for developing process parameters on production scale to optimize throughput, product quality, offgas behavior, and plant emissions. These instruments allow for offgas analysis, large-scale TGA, product quality observation, and thermal modeling. Using these tools, results from lab-scale techniques such as laser dilametry studies and traditional TGA/DTA analysis can be integrated. Often, the sintering step of a ceramification process is the limiting process step that controls the production throughput. Therefore, optimization of sintering behavior is important for overall process success. Furthermore, the capabilities of this instrumentation allows better understanding of plant emissions of key gases: volatile organic compounds (VOCs), volatile inorganics including some halide compounds, NO{sub x}, SO{sub x}, carbon dioxide, and carbon monoxide.

  15. Attachment of inorganic moieties onto aliphatic polyurethanes

    Directory of Open Access Journals (Sweden)

    Eliane Ayres

    2007-06-01

    Full Text Available Polyurethanes have been used in a series of applications due basically to their versatility in terms of controlling the behavior by altering basically the type of reagents used. However, for more specific and advanced applications, such as in membranes, biomaterials and sensors, well-organized and defined chemical functionalities are necessary. In this work, inorganic functionalities were incorporated into aliphatic polyurethanes (PU having different macromolecular architectures. Polyurethanes were synthesized using a polyether diol and dicyclohexylmethane 4,4' diisocyanate (H12-MDI. Polyurethanes having carboxylic acid groups were also produced by introducing 2,2- bis (hydroxymethyl propionic acid in the polymerization process. Inorganic functionalities were inserted into polyurethanes by reacting isocyanate end capped chains with aminopropyltriethoxysilane followed by tetraethoxysilane. PU having carboxylic acid groups yielded transparent samples after the incorporation of inorganic entities, as an evidence of smaller and better dispersed inorganic entities in the polymer network. FTIR and swelling measurements showed that polyurethanes having carboxylic acid groups had inorganic domains less packed, condensed and cross-linked when compared to polyurethanes with no carboxylic acid groups. Results also suggested that the progressive incorporation of inorganic moieties in both types of polyurethanes occurred in regions previously activated with inorganic functionalities, instead of by the creation of new domains. The temperatures of thermal decomposition and glass transition were also shifted to higher temperatures when inorganic functionalities were incorporated into polyurethanes.

  16. Harmfulness Assessment of Moulding Sands with a Geopolymer Binder and a New Hardener, in An Aspect of the Emission of Substances from the Btex Group

    Directory of Open Access Journals (Sweden)

    Bobrowski A.

    2015-04-01

    Full Text Available The harmfulness assessment of moulding sands with a geopolymer binder and a new hardener, in an aspect of the emission of substances from the BTEX group, was performed. Within the expedience project the new series of hardeners for the inorganic GEOPOL binder was developed. Before the introduction of the new system of moulding sands it was necessary to estimate their influence on the environment. To this aim the gasses emission from moulding sands subjected to the influence of liquid cast iron was tested with regard to the content of the gases from the BTEX group (benzene, toluene, ethylbenzene and xylenes. For the comparison the analogous investigations of the up to now applied moulding sands with the geopolymer binder, were performed. It was found that both systems of moulding sands binding emit similar amounts of gases, as well as similar amounts of substances from the BTEX group. Moulding sands with the GEOPOL binder are much more environmentally friendly than moulding sands with organic binders. The content of the BTEX group substances in gases emitted from moulding sands with the GEOPOL binder was approximately 10-times lower than in case of the moulding sands with organic binders.

  17. Biodegradable materials as foundry moulding sands binders

    Directory of Open Access Journals (Sweden)

    K. Major - Gabryś

    2015-07-01

    Full Text Available The aim of this article is to show the possibility of using biodegradable materials as part of the composition of foundry moulding and core sand binders. Research shows that moulding sands with biodegradable materials selected as binders are not only less toxic but are also better suited to mechanical reclamation than moulding sands with phenol-furfuryl resin. The use of biodegradable materials as additives to typical synthetic resins can result in their decreased toxicity and improved ability to reclamation as well as in accelerated biodegradation of binding material leftovers of mechanical reclamation.

  18. Irreversible volume growth in polymer-bonded powder systems: effects of crystalline anisotropy, particle size distribution, and binder strength

    Energy Technology Data Exchange (ETDEWEB)

    Maiti, A; Gee, R H; Hoffman, D; Fried, L E

    2007-08-22

    Pressed-powdered crystallites of intrinsically anisotropic materials have been shown to undergo irreversible volume expansion when subjected to repeated cycles of heating and cooling. We develop a coarse-grained (micron-scale) interaction Hamiltonian for this system and perform molecular dynamics simulations, which quantitatively reproduce the experimentally observed irreversible growth. The functional form and values of the interaction parameters at the coarse-grained level are motivated by our knowledge at the atomic/molecular scale, and allows a simple way to incorporate the effect of polymeric binder. We demonstrate that irreversible growth happens only in the presence of intrinsic crystalline anisotropy of the powder material, is mediated by particles much smaller than the average crystallite size, and can be significantly reduced in the presence of high-strength polymeric binder with elevated glass transition temperatures.

  19. ORGANIC/INORGANIC SUPPORT FOR IMMOBILIZING IRON ( Ⅲ )ACETYLACETONATE AND BIS(IMINO) PYRIDYL LIGAND CATALYST SYSTEM FOR ETHYLENE POLYMERIZATION%无机/有机复合载体负载乙酰丙酮铁/双亚胺基吡啶催化剂及其乙烯聚合

    Institute of Scientific and Technical Information of China (English)

    吴晶; 历伟; 蒋斌波; 王靖岱; 阳永荣

    2012-01-01

    采用溶胶-凝胶法,将苯乙烯-丙烯酸共聚物( PSA)包覆于955 Davison硅胶上得到无机/有机复合微球载体,并在2,6-二[1-(2-异丙基苯基亚胺基)乙基]吡啶/Fe(acac)3均相催化剂中浸渍后得到负载型双亚胺基吡啶铁催化剂.该催化剂在生产高结晶度(72%)聚乙烯的同时,还能生产一定量的α-烯烃.考察了不同膜材料以及聚合条件(不同助催化剂,压力,温度,Al/Fe摩尔比)对聚合活性以及聚合产物性能的影响,发现温度对聚合产物的α-烯烃与聚乙烯的质量比影响最大,助催化剂类型既影响催化剂的活性,也对最终产物的性质有着很大的影响.氯化镁处理的PSA作为膜材料时,负载2,6-二[1-(2-异丙基苯基亚胺基)乙基]吡啶/Fe(acac)3所得到聚乙烯分子量较低(Mw=11.9×104),结晶度较大(72%),熔融指数MI较高(2.35 g/10min),可作为双峰聚乙烯中的低分子量部分加以利用.%An organic/inorganic support of immobilizing catalysts for ethylene polymerization was devised. The composition of the hybrid catalyst is as following: styrene and acrylic copolymer ( PSA ) is the organic part for binding iron ( HI ) acetylacetonate and bis( imino)pyridyl ligand catalyst,and Si02(Davison 955 silical gel) is the inorganic part. The inorganic part is coated by the organic part (PSA) by sol-gel method. The catalyst could produce not only high crystallinity (72% ) polyethylene, but also or-olefin. We considered the impact of different membrane materials and polymerization conditions (different cocatalyst,pressure,temperature,Al/Fe molar ratio) to the polymerization activity and properties of polymers and found that temperature had the greatest impact to the weight ratio of oligomer to PE. Because of the poor thermal stability of catalyst, the catalytic activity significantly attenuated with increasing temperature. When pressure increased, catalytic activity would increase too. The relationship of pressure and catalytic

  20. Inorganic Materials

    Science.gov (United States)

    Černý, Radovan

    The separation of compounds by inorganic/organic boundary is of less importance for the structure determination by diffraction methods. More important for the diffraction is how the atoms build up larger building units and the crystal itself. A molecular/non-molecular boundary is therefore relevant for the choice of a structure determination method. Non-molecular compounds - also called extended solids - are constructed by bonds that extend "infinitely" in three dimensions through a crystal. These non-molecular crystals usually crystallize with higher symmetries, and atoms often occupy special Wyckoff positions. A review of actual methodology is given first, and then highlights and pitfalls of structure determination from powder diffraction, its problems and their solutions are shown and discussed using selected examples.

  1. Polyamidoamine dendrimer-based binders for high-loading lithium–sulfur battery cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharya, Priyanka; Nandasiri, Manjula I.; Lv, Dongping; Schwarz, Ashleigh M.; Darsell, Jens T.; Henderson, Wesley A.; Tomalia, Donald A.; Liu, Jun; Zhang, Ji-Guang; Xiao, Jie

    2016-01-01

    Lithium-sulfur (Li-S) batteries are regarded as one of the most promising candidates for next generation energy storage systems because of their ultra high theoretical specific energy. To realize the practical application of Li-S batteries, however, a high S active material loading is essential (>70 wt% in the carbon-sulfur (C-S) composite cathode and >2 mg cm-2 in the electrode). A critical challenge to achieving this high capacity in practical electrodes is the dissolution of the longer lithium polysulfide reaction intermediates in the electrolyte (resulting in loss of active material from the cathode and contamination of the anode due to the polysulfide shuttle mechanism). The binder material used for the cathode is therefore crucial as this is a key determinant of the bonding interactions between the active material (S) and electronic conducting support (C), as well as the maintenance of intimate contact between the electrode materials and current collector. The battery performance can thus be directly correlated with the choice of binder, but this has received only minimal attention in the relevant Li-S battery published literature. Here, we investigated the application of polyamidoamine (PAMAM) dendrimers as functional binders in Li-S batteries—a class of materials which has been unexplored for electrode design. By using dendrimers, it is demonstrated that high S loadings (>4 mg cm-2) can be easily achieved using "standard" (not specifically tailored) materials and simple processing methods. An exceptional electrochemical cycling performance was obtained (as compared to cathodes with conventional linear polymeric binders such as carboxymethyl cellulose (CMC) and styrene-butadiene rubber (SBR)) with >100 cycles and 85-98% capacity retention, thus demonstrating the significant utility of this new binder architecture which exhibits critical physicochemical properties and flexible nanoscale design parameters (CNDP's).

  2. A molecular dynamics study of the role of molecular water on the structure and mechanics of amorphous geopolymer binders

    Science.gov (United States)

    Sadat, Mohammad Rafat; Bringuier, Stefan; Asaduzzaman, Abu; Muralidharan, Krishna; Zhang, Lianyang

    2016-10-01

    In this paper, molecular dynamics simulations are used to study the effect of molecular water and composition (Si/Al ratio) on the structure and mechanical properties of fully polymerized amorphous sodium aluminosilicate geopolymer binders. The X-ray pair distribution function for the simulated geopolymer binder phase showed good agreement with the experimentally determined structure in terms of bond lengths of the various atomic pairs. The elastic constants and ultimate tensile strength of the geopolymer binders were calculated as a function of water content and Si/Al ratio; while increasing the Si/Al ratio from one to three led to an increase in the respective values of the elastic stiffness and tensile strength, for a given Si/Al ratio, increasing the water content decreased the stiffness and strength of the binder phase. An atomic-scale analysis showed a direct correlation between water content and diffusion of alkali ions, resulting in the weakening of the AlO4 tetrahedral structure due to the migration of charge balancing alkali ions away from the tetrahedra, ultimately leading to failure. In the presence of water molecules, the diffusion behavior of alkali cations was found to be particularly anomalous, showing dynamic heterogeneity. This paper, for the first time, proves the efficacy of atomistic simulations for understanding the effect of water in geopolymer binders and can thus serve as a useful design tool for optimizing composition of geopolymers with improved mechanical properties.

  3. Glyoxalated polyacrylamide as a covalently attachable and rapidly cross-linkable binder for Si electrode in lithium ion batteries

    Science.gov (United States)

    Yoo, Jung-Keun; Jeon, Jaebeom; Kang, Kisuk; Jung, Yeon Sik

    2017-01-01

    Recently, investigation of Si-based anode materials for rechargeable battery applications garnered much interest due to its exceptionally high capacity. High-capacity Si anode ( 4,200 mAhg-1) is highly desirable for the replacement of conventional graphite anode (storage applications such as in electric vehicles (EVs) and energy storage systems (ESSs) for renewable energy sources. However, Si-based anodes suffer from poor cycling stability due to their large volumetric changes during repeated Li insertion. Therefore, development of highly efficient binder materials that can suppress the volume change of Si is one of the most essential parts of improving the performance of batteries. We herein demonstrate highly cross-linked polymeric binder (glyoxalated polyacrylamide) with an enhanced mechanical property by applying wet-strengthening chemistry used in paper industry. We found that the degree of cross-linking can be systematically adjusted by controlling the acidity of the slurry and has a profound effect on the cell performance using Si anode. The enhanced cycle performance of Si nanoparticles obtained by treating the binder at pH 4 can be explained by its strong interaction between the binder and Si surface and current collector, and also rigidity of binder by cross-linking. [Figure not available: see fulltext.

  4. THE STUDY ON MECHANISM OF BINDER MIGRATION DURING COATING PROCESS

    Institute of Scientific and Technical Information of China (English)

    YunLiang; KefuChen

    2004-01-01

    Binder migration during coating process and themechanism of binder migration were studied in thispaper. After the latex was tagged by osmium, thedegree of binder migration was measured byenergy-dispersive X-ray spectrometer. For the wetsample just after coating application, the realinformation of binder distribution was kept byquenching the sample in liquid nitrogen followed byfreeze-drying. The results showed: under thecondition of this research, binder migration occurredboth in the process of coating application and drying.But the amount of binder migration occurred duringcoating application was much little than that occurredduring drying. The mechanism of binder migrationduring the process of coating application was studiedby force analyses. And one viewpoint was proposedthat was binder migration was caused by Magnusforce and Saffman force.

  5. THE STUDY ON MECHANISM OF BINDER MIGRATION DURING COATING PROCESS

    Institute of Scientific and Technical Information of China (English)

    Yun Liang; Kefu Chen

    2004-01-01

    Binder migration during coating process and the mechanism of binder migration were studied in this paper. After the latex was tagged by osmium, the degree of binder migration was measured by energy-dispersive X-ray spectrometer. For the wet sample just after coating application, the real information of binder distribution was kept by quenching the sample in liquid nitrogen followed by freeze-drying. The results showed: under the condition of this research, binder migration occurred both in the process of coating application and drying.But the amount of binder migration occurred during coating application was much little than that occurred during drying. The mechanism of binder migration during the process of coating application was studied by force analyses. And one viewpoint was proposed that was binder migration was caused by Magnus force and Saffman force.

  6. Modification Bituminous Binders Petroleum Resin (Based on C9 Fraction

    Directory of Open Access Journals (Sweden)

    Elena A. Chigorina

    2015-12-01

    Full Text Available The goal of the present study is to measure the basic parameters of a bituminous binder obtained by modification of the BND 60/90 binder with petroleum resin, for both dynamic and static modification modes.

  7. Three-year performance of in-situ solidified/stabilised soil using novel MgO-bearing binders.

    Science.gov (United States)

    Jin, Fei; Wang, Fei; Al-Tabbaa, Abir

    2016-02-01

    A new group of MgO-bearing binders has been developed recently which showed improved sustainability and technical performance compared to Portland cement (PC). However, the application of these MgO-bearing binders in the Solidification/Stabilisation (S/S) techniques is very limited. This study investigates the three-year performance of a highly contaminated soil treated by in-situ S/S using MgO-bearing binders and PC. The core quality, strength, permeability and the leaching properties of the S/S materials were evaluated. The effects of binder composition, addition of inorgano-organo-clay (IOC) and the grout content on the properties of the 3-y S/S materials are discussed. It is found that although MgO alone provided negligible strength to the soil, it is superior in immobilising both inorganic and organic contaminants. Replacing MgO by ground granulated blast-furnace slag (GGBS) significantly enhanced the strength while also performed well in immobilising the contaminants. The improved pH buffering capacity was attributed to the low solubilities of brucite and hydrotalcite-like phases formed in the MgO-bearing binders, and was also the reason for the improved performance in stabilising contaminants. The addition of IOC slightly decreased the strength and the permeability of the S/S materials but inconsistent effect on the contaminant immobilisation was found depending on the binder composition. This study showed no degradation of the S/S materials after 3 y exposure to field conditions and has proved the applicability and the advantages of MgO-bearing binders over PC in S/S.

  8. Near-infrared light responsive polymeric nanocomposites for cancer therapy.

    Science.gov (United States)

    Min, Cong; Zou, Xueqing; Yang, Quanzhu; Liao, Liqiong; Zhou, Guofu; Liu, Lijian

    2016-11-22

    Inorganic nanoparticles, which can absorb and convert near infrared (NIR) light to heat to ablate cancer cells, have been widely investigated in photothermal therapy. However, the inherent poor solubility and acute systemic toxicity of these inorganic particles hinder their application in clinical practice. Polymeric nnanocomposites materials containing both inorganic nanoparticles and polymers could be harnessed to achieve enhanced photothermal therapeutic effect as well as improved biocompatibility and multi-responsiveness. Synergistic chemo-photothermal efficacy towards cancer cells and tumor tissue can thus be realized through such multi-functional and multi-responsive polymeric nanocomposites. In this review, the recent developments in polymeric nanocomposites based on different types of inorganic nanoparticles (i.e. gold, carbon nanotube, graphene, and up-conversion nanoparticles) for NIR-triggered cancer therapy are summarized.

  9. Expandable Polystyrene Nanocomposites Prepared by Styrene/Nano-inorganic Particle by In-situ Suspension Polymerization%苯乙烯/纳米无机粒子原位悬浮聚合制备EPS纳米复合材料

    Institute of Scientific and Technical Information of China (English)

    韩冰; 李杨; 申凯华; 王玉荣

    2012-01-01

    Based on in situ radical suspension polymerization, polystyrene nanocomposites were prepared from styrene and nano-inorganic particle. Then, hexane was added to prepare expandable polystyrene nanocomposites (EPSNC). EPSNC were characterized by means of gel permeation chromatography, thermo gravimetric analyzer, and scanning electron microscope. It showed that at a suitable content of nano-inorganic particle, the molecular weight of EPSNC had a narrower distribution, the thermal stability of EPSNC was improved significantly. In addition, the nano- inorganic particle showed a nucleation function in the foaming process. The nano-inorganic particle dispersed finely in polystyrene, resulting in small and uniform closed-cell structure.%采用自由基原位悬浮聚合方法,由苯乙烯/纳米无机粒子(NIP)聚合制备聚苯乙烯纳米复合材料(PSNC),再以戊烷为发泡剂制备了可发性聚苯乙烯纳米复合材料(EPSNC),筛选了NIP改性剂的种类。利用凝胶渗透色谱仪和热重分析仪对EPSNC进行表征,研究了EPSNC的分子结构和热性能,采用扫描电子显微镜对EPSNC泡体内部微观形貌进行表征,研究NIP含量对其泡体微观形貌的影响规律。结果表明,以钛酸酯偶联剂改性NIP(M-NIP)聚合产率最高;M-NIP用量在一定范围内对EPSNC的相对分子质量影响不大,但相对分子质量分布变窄;含有M-NIP的EPSNC的热稳定性明显提高;EPSNC发泡时NIP起成核作用,M-NIP能够均匀地分散在EPSNC中,其泡孔堆积有序,细密一致,且多为闭孔结构。

  10. Science Update: Inorganic Chemistry.

    Science.gov (United States)

    Rawls, Rebecca

    1981-01-01

    Describes areas of inorganic chemistry which have changed dramatically in the past year or two, including photochemistry, electrochemistry, organometallic complexes, inorganic reaction theory, and solid state chemistry. (DS)

  11. Characteristic of Core Manufacturing Process with Use of Sand, Bonded by Ecological Friendly Nonorganic Binders

    Directory of Open Access Journals (Sweden)

    A. Fedoryszyn

    2013-07-01

    Full Text Available Mechanization of the process of core making with the use of inorganic and organic binders is based, almost solely, on core blowing machines. Presently the core blowing machines are equipped with tools and devices that allow for application of different technologies of core making. Cold-box, hot-box and warm-air technologies require that core blowing machines shall be additionally equipped with either core-box pre-heating system or gas purging and neutralization system, or hot air purging systems.

  12. Chemistry and applications of inorganic-organic polymers : organically modified silicates

    OpenAIRE

    Schmidt, Helmut K.; Seiferling, Bernhard

    1986-01-01

    The conbination of inorganic polymeric networks with organic components leads ot inorganic-organic polymers. A convenient method for the introduction of organic radials into an inorganic backbone is the use of aorganosubstituted silico esters in a polycondensation process. This leads to ≡Si-O-Si≡ network containing materials, so-called organically modified silicates (ORMOSILs). For the synthesis of the inorganic backbone, in opposition to the high temperature preparation of non-me...

  13. BINDER DRAINAGE TEST FOR POROUS MIXTURES MADE BY VARYING THE MAXIMUM AGGREGATE SIZES

    Directory of Open Access Journals (Sweden)

    Hardiman Hardiman

    2004-01-01

    Full Text Available Binder drainage occurs with mixes of small aggregate surface area particularly porous asphalt. The binder drainage test, developed by the Transport Research Laboratory, UK, is commonly used to set an upper limit on the acceptable binder content for a porous mix. This paper presents the results of a laboratory investigation to determine the effects of different binder types on the binder drainage characteristics of porous mix made of various maximum aggregate sizes 20, 14 and 10 mm. Two types of binder were used, conventional 60/70 pen bitumen, and styrene butadiene styrene (SBS modified bitumen. The amount of binder lost through drainage after three hours at the maximum mixing temperature were measured in duplicate for mixes of different maximum sizes and binder contents. The maximum mixing temperature adopted depends on the types of binder used. The retained binder is plotted against the initial mixed binder content, together with the line of equality where the retained binder equals the mixed binder content. The results indicate the significant contribution of using SBS modified bitumen to increase the target bitumen binder content. Their significance is discussed in terms of target binder content, the critical binder content, the maximum mixed binder content and the maximum retained binder content values obtained from the binder drainage test. It was concluded that increasing maximum aggregate sizes decrease the maximum retained binder content, critical binder content, target binder content, maximum mixed binder content, and mixed content for both binders, but however for all mixtures, SBS is the highest.

  14. Phenomena during thermal removal of binders

    Science.gov (United States)

    Hrdina, Kenneth Edward

    The research presented herein has focused on debinding of an ethylene copolymer from a SiC based molded ceramic green body. Examination of the binder burnout process was carried out by breaking down the process into two distinct regions: those events which occur before any weight loss begins, and those events occurring during binder removal. Below the temperature of observed binder loss (175sp°C), both reversible and irreversible displacement was observed to occur. The displacement was accounted for by relaxation of molding stresses, thermal expansion of the system, and melting of the semicrystalline copolymer occurring during heating. Upon further heating the binder undergoes a two stage thermal degradation process. In the first stage, acetic acid is the only degradation product formed, as determined by GC/MS analysis. In this stage, component shrinkage persisted and it was found that one unit volume of shrinkage corresponded with one unit volume of binder removed, indicating that no porosity developed. The escaping acetic acid effluents must diffuse through liquid polymer filled porous regions to escape. The gas pressure of the acetic acid species produced in the first stage of the thermal degradation may exceed the ambient pressure promoting bubble formation. Controlling the heating rate of the specimen maintains the gas pressure below the bubbling threshold and minimizes the degradation time. Experiments have determined the kinetics of the reaction in the presence of the high surface area (10-15msp2/g) ceramic powder and then verified that acetic acid was diffusing through the polymer phase to the specimen surface where evaporation is taking place. The sorption method measured the diffusivity and activity of acetic acid within the filled ceramic system within a TGA. These data were incorporated into a Fickian type model which included the rate of generation of the diffusing species. The modeling process involved prediction of the bloating temperature as a

  15. MESO—STRUCTURED POLYMERIC HYDROGELS

    Institute of Scientific and Technical Information of China (English)

    Zhen-zhongYang; Jian-huaRong; DanLi

    2003-01-01

    Meso-structured(opal and inverse opal) polymeric hydrogels of varied morphology and composition were prepared by using two methods:post-modification of the template-synthesized structured polymers and templatepolymerization of functional monomers.A polyacrylic acid based inverse opal hydrogel was chosen to demonstrate its fast pH response by changing color,which is important in designing tunable photonic crystals.Template effects of the hydrogels on controlling structure of the template-synthesized inorganic materials were discussed.The catalytic effect of acid groups in the templates was emphasized for a preferential formation of TiO2 in the region containing acid groups,which allowed duplicating inorganic colloidal crystals from colloidal crystal hydrogels (or macroporous products from macroporous hydrogels) via one step duplication.

  16. MESO-STRUCTURED POLYMERIC HYDROGELS

    Institute of Scientific and Technical Information of China (English)

    Zhen-zhong Yang; Jian-hua Rong; Dan Li

    2003-01-01

    Meso-structured (opal and inverse opal) polymeric hydrogels of varied morphology and composition were prepared by using two methods: post-modification of the template-synthesized structured polymers and templatepolymerization of functional monomers. A polyacrylic acid based inverse opal hydrogel was chosen to demonstrate its fast pH response by changing color, which is important in designing tunable photonic crystals. Template effects of the hydrogels on controlling structure of the template-synthesized inorganic materials were discussed. The catalytic effect of acid groups inthe templates was emphasized for a preferential formation of TiO2 in the region containing acid groups, which allowed duplicating inorganic colloidal crystals from colloidal crystal hydrogels (or macroporous products from macroporous hydrogels) via one step duplication.

  17. Polysialates binders preparation and their influence to shear strength of foundry sand mixtures

    Directory of Open Access Journals (Sweden)

    R. Fridrich

    2008-07-01

    Full Text Available This paper deals with polysialates water-glasses preparation. There were used various procedures with the goal to create inorganic polymer on silicon and aluminum base. The one composed of SiO2 and AlO4 tetrahedron chains. For the preparation was concentrated NaOH solution used together with metakaolinite in a way low-temperature synthesis in the presence of alkaline silicate: higher pressure and temperature (autoclave to direct making of alkaline silicate made of sand, NaOH with metakaolinite addition and by melting fritted glass together with metakaolinite and dissolution in autoclave. The dissolving effectivity was evaluated by the concentration of aluminum in alkaline silicate and by the influence to reduce strengths after heat exposition with this inorganic binder.

  18. Organically modified clays as binders of fumonisins in feedstocks.

    Science.gov (United States)

    Baglieri, Andrea; Reyneri, Amedeo; Gennari, Mara; Nègre, Michèle

    2013-01-01

    This study reports an investigation on the ability of organically modified clays to bind mycotoxins, fumonisins B1 (FB1) and B2 (FB2). Organically modified clays are commercia materials prepared from natural clays, generally montmorillonite, by exchanging the inorganic cation with an ammonium organic cation. A screening experiment conducted on 13 organically modified clays and 3 nonmodified clays, used as controls, has confirmed that the presence of an organic cation in the clay interlayer promoted the adsorption of both fumonisins. On the basis of the results of the screening test, four modified clays and a Na-montmorillonite were selected for the determination of the adsorption kinetics and isotherms. On all the tested materials adsorption took place within one hour of contact with fumonisins solutions. Adsorption isotherms have pointed out that the modified clays exhibited a higher adsorptive capacity than the unmodified clay. It was also demonstrated that, notwithstanding the reduced structural difference between FB1 and FB2, they were differently adsorbed on the modified clays. Addition of 2% modified clays to contaminated maize allowed a reduction of more than 70% and 60% of the amount of FB1and FB2 released in solution. Although in vivo experiments are required to confirm the effectiveness of the organically modified clays, these preliminary results suggest that these materials are promising as fumonisins binders.

  19. Cold-Setting Inkjet Printed Titania Patterns Reinforced by Organosilicate Binder

    Directory of Open Access Journals (Sweden)

    Marcela Králová

    2015-09-01

    Full Text Available A hybrid organo-silica sol was used as a binder for reinforcing of commercial titanium dioxide nanoparticles (Evonic P25 deposited on glass substrates. The organo-silica binder was prepared by the sol-gel process and mixtures of titania nanoparticles with the binder in various ratios were deposited by materials printing technique. Patterns with both positive and negative features down to 100 µm size and variable thickness were reliably printed by Fujifilm Dimatix inkjet printer. All prepared films well adhered onto substrates, however further post-printing treatment proved to be necessary in order to improve their reactivity. The influence of UV radiation as well as of thermal sintering on the final electrochemical and photocatalytic properties was investigated. A mixture containing 63 wt % of titania delivered a balanced compromise of mechanical stability, generated photocurrent density and photocatalytic activity. Although the heat treated samples yielded generally higher photocurrent, higher photocatalytic activity towards model aqueous pollutant was observed in the case of UV cured samples because of their superhydrophilic properties. While heat sintering remains the superior processing method for inorganic substrates, UV-curing provides a sound treatment option for heat sensitive ones.

  20. Cold-Setting Inkjet Printed Titania Patterns Reinforced by Organosilicate Binder.

    Science.gov (United States)

    Králová, Marcela; Dzik, Petr; Kašpárek, Vít; Veselý, Michal; Cihlář, Jaroslav

    2015-09-11

    A hybrid organo-silica sol was used as a binder for reinforcing of commercial titanium dioxide nanoparticles (Evonic P25) deposited on glass substrates. The organo-silica binder was prepared by the sol-gel process and mixtures of titania nanoparticles with the binder in various ratios were deposited by materials printing technique. Patterns with both positive and negative features down to 100 µm size and variable thickness were reliably printed by Fujifilm Dimatix inkjet printer. All prepared films well adhered onto substrates, however further post-printing treatment proved to be necessary in order to improve their reactivity. The influence of UV radiation as well as of thermal sintering on the final electrochemical and photocatalytic properties was investigated. A mixture containing 63 wt % of titania delivered a balanced compromise of mechanical stability, generated photocurrent density and photocatalytic activity. Although the heat treated samples yielded generally higher photocurrent, higher photocatalytic activity towards model aqueous pollutant was observed in the case of UV cured samples because of their superhydrophilic properties. While heat sintering remains the superior processing method for inorganic substrates, UV-curing provides a sound treatment option for heat sensitive ones.

  1. Biokompatible Polymere

    Science.gov (United States)

    Ha, Suk-Woo; Wintermantel, Erich; Maier, Gerhard

    Der klinische Einsatz von synthetischen Polymeren begann in den 60-er Jahren in Form von Einwegartikeln, wie beispielsweise Spritzen und Kathetern, vor allem aufgrund der Tatsache, dass Infektionen infolge nicht ausreichender Sterilität der wiederverwendbaren Artikel aus Glas und metallischen Werkstoffen durch den Einsatz von sterilen Einwegartikeln signifikant reduziert werden konnten [1]. Die Einführung der medizinischen Einwegartikel aus Polymeren erfolgte somit nicht nur aus ökonomischen, sondern auch aus hygienischen Gründen. Wegen der steigenden Anzahl synthetischer Polymere und dem zunehmenden Bedarf an ärztlicher Versorgung reicht die Anwendung von Polymeren in der Medizin von preisgünstigen Einwegartikeln, die nur kurzzeitig intrakorporal eingesetzt werden, bis hin zu Implantaten, welche über eine längere Zeit grossen Beanspruchungen im menschlichen Körper ausgesetzt sind. Die steigende Verbreitung von klinisch eingesetzten Polymeren ist auf ihre einfache und preisgünstige Verarbeitbarkeit in eine Vielzahl von Formen und Geometrien sowie auf ihr breites Eigenschaftsspektrum zurückzuführen. Polymere werden daher in fast allen medizinischen Bereichen eingesetzt.

  2. Curing Reaction Model of Epoxy Asphalt Binder

    Institute of Scientific and Technical Information of China (English)

    QIAN Zhendong; CHEN Leilei; WANG Yaqi; SHEN Jialin

    2012-01-01

    In order to understand the strength developing law of the epoxy asphalt mixture,a curing reaction model of the epoxy asphalt binder was proposed based upon the thermokinetic analysis.Given some assumptions,the model was developed by applying the Kissinger law as well as Arrhenius equation,and the differential scanning calorimetry was performed for estimating the model parameters.To monitor the strength development of the epoxy asphalt mixture,a strength test program was employed and then results were compared to those produced from the proposed model.The comparative evaluation shows that a good consistency exists between the outputs from test program and the proposed model,indicating that the proposed model can be used effectively for simulating the curing reaction process for the epoxy asphalt binder and predicting the strength development for the epoxy asphalt mixture.

  3. Composite binders for concrete with reduced permeability

    Science.gov (United States)

    Fediuk, R.; Yushin, A.

    2016-02-01

    Composite binder consisting of cement (55%), acid fly ash (40%) and limestone (5%) has been designed. It is obtained by co-milling to a specific surface of 550 kg/m2, it has an activity of 77.3 MPa and can produce a more dense cement stone structure. Integrated study revealed that the concrete on the composite binder basis provides an effective diffusion coefficient D. So we can conclude that the concrete layer protects buildings from toxic effects of expanded polystyrene. Low water absorption of the material (2.5% by weight) is due to the structure of its cement stone pore space. Besides lime powder prevents the penetration of moisture, reduces water saturation of the coverage that has a positive effect on useful life period. It also explains rather low water vapor permeability of the material - 0.021 mg/(m- hour-Pa).

  4. Zirconium phosphate binder for periclase refractories

    Energy Technology Data Exchange (ETDEWEB)

    Volceanov, E. [ICEM S.A., Bucharest (Romania). Metallurgical Research Inst.; Georgescu, M.; Volceanov, A. [Universitatea Politehnica, Bucharest (Romania). Faculty of Industrial Chemistry; Mihalache, F. [REAL S.A., Ploiesti (Romania)

    2002-07-01

    Present paper brings information concerning the physical-mechanical properties of some high thermal resistant composites with phosphate bonding obtained from periclase clinker as solid component and various zirconium phosphates solutions as liquid component: ZI, ZII and ZIII. All these solutions were prepared from hydrous zirconia and orthophosphoric acid. The batches corresponding to a weight ratio solid / liquid = 3 / 1, have shown a good hardening behavior at normal temperature, especially for the ZII binder. Such compositions exhibit a very good thermal-mechanical behavior in the temperature range 1400 C - 1750 C. X-ray diffraction and electronomicroscopy (TEM) analysis provided information concerning the evolution of phase composition and microstructure during heating of the thermal resistant specimens chemically bound with a zirconium phosphate binder. (orig.)

  5. Valorization of phosphogypsum as hydraulic binder.

    Science.gov (United States)

    Kuryatnyk, T; Angulski da Luz, C; Ambroise, J; Pera, J

    2008-12-30

    Phosphogypsum (calcium sulfate) is a naturally occurring part of the process of creating phosphoric acid (H(3)PO(4)), an essential component of many modern fertilizers. For every tonne of phosphoric acid made, from the reaction of phosphate rock with acid, commonly sulfuric acid, about 3t of phosphogypsum are created. There are three options for managing phosphogypsum: (i) disposal or dumping, (ii) stacking, (iii) use-in, for example, agriculture, construction, or landfill. This paper presents the valorization of two Tunisian phosphogypsums (referred as G and S) in calcium sulfoaluminate cement in the following proportions: 70% phosphogypsum-30% calcium sulfoaluminate clinker. The use of sample G leads to the production of a hydraulic binder which means that it is not destroyed when immersed in water. The binder including sample S performs very well when cured in air but is not resistant in water. Formation of massive ettringite in a rigid body leads to cracking and strength loss.

  6. Modular mobility investigation of polymer binder bitumen

    Science.gov (United States)

    Ayupov, D.; Makarov, D.; Murafa, A.; Khozin, V.; Khakimullin, Y.; Sundukov, V.; Khakimov, A.; Gizatullin, B.

    2015-01-01

    This paper is aimed to obtain polymer binder bitumen for the road applications with improved properties. Objectives included studying the degradation of crumb rubber during devulcanization in melted petroleum bitumen for its modification and resulted structural properties of bitumen. Using equilibrium swelling technique reduced density of the polymer chains was observed and analysis of sol-gel fractions showed a significant decrease in gel fraction. Under selected method of devulcanization 64% of the backbone rubber remained. With The H1 NMR relaxation method the reduction of bitumen molecular mobility was observed due to thickening of its light fractions. The effectiveness of devulcanization was optimized using a new agent in a powder form and vacuum application. The developed binder has an improved spectrum of physical and technical properties such as softening point temperature, hardness, elasticity, frost resistance, low temperature characteristics.

  7. High Performance Binder for EMCDB Propellants

    Directory of Open Access Journals (Sweden)

    V. K. Bhat

    1995-01-01

    Full Text Available A novel block polymer has been synthesised from caprolactone using hydroxy terminated polybutadiene as ring opening initiator. Usefulness of this polymer as propellant binder has been studied by generating data on physico-chemical properties of the polymer. The polymer exhibited high miscibility with nitrate ester and high solid loading capability. Preliminary data generated on typical propellant formulation indicated higher performance as compared to composite propellant.

  8. A Novel Polar Copolymer Design as a Multi-Functional Binder for Strong Affinity of Polysulfides in Lithium-Sulfur Batteries

    Science.gov (United States)

    Jiao, Yu; Chen, Wei; Lei, Tianyu; Dai, Liping; Chen, Bo; Wu, Chunyang; Xiong, Jie

    2017-03-01

    High energy density, low cost and environmental friendliness are the advantages of lithium-sulfur (Li-S) battery which is regarded as a promising device for electrochemical energy storage systems. As one of the important ingredients in Li-S battery, the binder greatly affects the battery performance. However, the conventional binder has some drawbacks such as poor capability of absorbing hydrophilic lithium polysulfides, resulting in severe capacity decay. In this work, we reported a multi-functional polar binder (AHP) by polymerization of hexamethylene diisocyanate (HDI) with ethylenediamine (EDA) bearing a large amount of amino groups, which were successfully used in electrode preparation with commercial sulfur powder cathodes. The abundant amide groups of the binder endow the cathode with multidimensional chemical bonding interaction with sulfur species within the cathode to inhibit the shuttling effect of polysulfides, while the suitable ductility to buffer volume change. Utilizing these advantageous features, composite C/S cathodes based the binder displayed excellent capacity retention at 0.5 C, 1 C, 1.5 C, and 3 C over 200 cycles. Accompany with commercial binder, AHP may act as an alternative feedstock to open a promising approach for sulfur cathodes in rechargeable lithium battery to achieve commercial application.

  9. Shear History Extensional Rheology Experiment II (SHERE II) Microgravity Rheology with Non-Newtonian Polymeric Fluids

    Science.gov (United States)

    Jaishankar, Aditya; Haward, Simon; Hall, Nancy Rabel; Magee, Kevin; McKinley, Gareth

    2012-01-01

    The primary objective of SHERE II is to study the effect of torsional preshear on the subsequent extensional behavior of filled viscoelastic suspensions. Microgravity environment eliminates gravitational sagging that makes Earth-based experiments of extensional rheology challenging. Experiments may serve as an idealized model system to study the properties of lunar regolith-polymeric binder based construction materials. Filled polymeric suspensions are ubiquitous in foods, cosmetics, detergents, biomedical materials, etc.

  10. Microchemical Study of Pigments and Binders in Polychrome Relics from Maiji Mountain Grottoes in Northwestern China.

    Science.gov (United States)

    Liu, Luyao; Shen, Wei; Zhang, Bingjian; Ma, Qian

    2016-08-01

    In this study, an integrated analytical method was developed to investigate the composition of both the inorganic pigments and organic binders of polychrome relics in Maiji Mountain Grottoes in northwestern China. Cross-sections of each sample were prepared at the beginning of the study, and all experiments were carried out on these cross-sections. Polychromic structures were revealed by optical microscopy and scanning electron microscopy-backscattered electron imaging. Inorganic materials were determined by using SEM coupled with an energy dispersive spectrometer and μ-Raman spectrometer, whereas organic materials were identified by staining techniques and highly sensitive and specific immunofluorescence microscopy. Data showed that the red colors are attributed to one or two pigments of red ochre, cinnabar, and minium; the blue pigment is natural lazurite; the green pigment is ascribed to atacamite; the white color is attributed to potassium feldspar; and the black surface is formed by the discoloration of minium to plattnerite under the influence of environmental factors. Regarding organic binders used in painting and preparation layers, mammalian animal glue and chicken egg white were both found alone or in mixture. Finally, the conclusion is made that the Secco technique is employed in polychrome relics from Maiji Mountain Grottoes.

  11. Producing ORMOSIL scaffolds by femtosecond laser polymerization

    Science.gov (United States)

    Matei, A.; Zamfirescu, M.; Radu, C.; Buruiana, E. C.; Buruiana, T.; Mustaciosu, C.; Petcu, I.; Radu, M.; Dinescu, M.

    2012-07-01

    Structures with different geometries and sizes were built via direct femtosecond laser writing, starting from new organic/inorganic hybrid monomers based on hybrid methacrylate containing triethoxysilane, in addition to urethane and urea groups. Multifunctional oligomer of urethane dimethacrylate type was chosen as comonomer in polymerization experiments because dimethacrylates give rise to the formation of a polymer network, having a number of favorable properties including biocompatibility and surface nanostructuring. Free standing polymeric structures were designed and created in order to be tested in fibroblast cells culture. Investigations of the cellular adhesion, proliferation, and viability of L929 mouse fibroblasts on free-standing laser processed scaffolds were performed for different scaffold designs.

  12. Inorganic nanocarriers for platinum drug delivery

    Directory of Open Access Journals (Sweden)

    Ping’an Ma

    2015-12-01

    Full Text Available Nowadays platinum drugs take up almost 50% of all the clinically used anticancer drugs. Besides cisplatin, novel platinum agents including sterically hindered platinum (II drugs, chemically reductive platinum (IV drugs, photosensitive platinum (IV drugs, and multinuclear platinum drugs have been developed recently, with a few entering clinic trials. Rapid development of nanobiotechnology makes targeted delivery of anticancer platinum agents to the tumor site possible, while simultaneously minimizing toxicity and maximizing the drug efficacy. Being versatile drug carriers to deliver platinum drugs, inorganic nanovehicles such as gold nanoparticles, iron oxide nanomaterials, carbon nanotubes, mesoporous nanosilica, metal-organic frameworks (MOFs, have been extensively studied over the past decades. In contrast to conventional polymeric and lipid nanoparticles, inorganic nanoparticles based drug carriers are peculiar as they have shown excellent theranostic effects, revealing themselves an indispensable part of future nanomedicine. Here, we will elaborate recent research advances on fabrication of inorganic nanoparticles for platinum drug delivery.

  13. Microporous Inorganic Membranes as Proton Exchange Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Vichi, F.M. Tejedor-Tejedor, M.I. Anderson, Marc A

    2002-08-28

    Porous oxide electrolyte membranes provide an alternative approach to fabricating proton exchange membrane fuel cells based on inorganic materials. This study focused on elucidating the properties of these inorganic membranes that make them good electrolyte materials in membrane electrode assemblies; in particular, we investigated several properties that affect the nature of proton conductivity in these membranes. This report discusses our findings on the effect of variables such as site density, amount of surface protonation and surface modification on the proton conductivity of membranes with a fixed pore structure under selected conditions. Proton conductivities of these inorganic membranes are similar to conductivities of nafion, the polymeric membrane most commonly used in low temperature fuel cells.

  14. Conductive Polymer Binder for High-Tap-Density Nanosilicon Material for Lithium-Ion Battery Negative Electrode Application.

    Science.gov (United States)

    Zhao, Hui; Wei, Yang; Qiao, Ruimin; Zhu, Chenhui; Zheng, Ziyan; Ling, Min; Jia, Zhe; Bai, Ying; Fu, Yanbao; Lei, Jinglei; Song, Xiangyun; Battaglia, Vincent S; Yang, Wanli; Messersmith, Phillip B; Liu, Gao

    2015-12-09

    High-tap-density silicon nanomaterials are highly desirable as anodes for lithium ion batteries, due to their small surface area and minimum first-cycle loss. However, this material poses formidable challenges to polymeric binder design. Binders adhere on to the small surface area to sustain the drastic volume changes during cycling; also the low porosities and small pore size resulting from this material are detrimental to lithium ion transport. This study introduces a new binder, poly(1-pyrenemethyl methacrylate-co-methacrylic acid) (PPyMAA), for a high-tap-density nanosilicon electrode cycled in a stable manner with a first cycle efficiency of 82%-a value that is further improved to 87% when combined with graphite material. Incorporating the MAA acid functionalities does not change the lowest unoccupied molecular orbital (LUMO) features or lower the adhesion performance of the PPy homopolymer. Our single-molecule force microscopy measurement of PPyMAA reveals similar adhesion strength between polymer binder and anode surface when compared with conventional polymer such as homopolyacrylic acid (PAA), while being electronically conductive. The combined conductivity and adhesion afforded by the MAA and pyrene copolymer results in good cycling performance for the high-tap-density Si electrode.

  15. Binder content influences on chloride ingress in concrete

    Energy Technology Data Exchange (ETDEWEB)

    Dhir, R.K.; Jones, M.R.; McCarthy, M.J. [Univ. of Dundee (United Kingdom)

    1996-12-01

    The reported study looked at the effect of reducing free water contents, and thereby binder contents, and thereby binder contents, on the ingress of chloride in concrete. Concretes with equal water/binder ratio (and design strength), but with water contents reduced by up to 30 liters/m{sup 3}, were tested for chloride diffusion (D) and penetration. The quality of the microstructure was inferred from initial surface absorption tests (ISAT). The results show no practical difference in chloride durability between the corresponding concretes, and that reducing the binder content, (providing that the water/binder ratio is maintained) is not likely to be detrimental. However, the results reported underline the importance of binder type, in this case PFA. Implications of the results are discussed and, in light of the findings, whether specifications which demand minimum cement contents are justified.

  16. Microscopy Characterization of Silica-Rich Agrowastes to be used in Cement Binders: Bamboo and Sugarcane Leaves.

    Science.gov (United States)

    Roselló, Josefa; Soriano, Lourdes; Santamarina, M Pilar; Akasaki, Jorge L; Melges, José Luiz P; Payá, Jordi

    2015-10-01

    Agrowastes are produced worldwide in huge quantities and they contain interesting elements for producing inorganic cementing binders, especially silicon. Conversion of agrowastes into ash is an interesting way of yielding raw material used in the manufacture of low-CO2 binders. Silica-rich ashes are preferred for preparing inorganic binders. Sugarcane leaves (Saccharum officinarum, SL) and bamboo leaves (Bambusa vulgaris, BvL and Bambusa gigantea, BgL), and their corresponding ashes (SLA, BvLA, and BgLA), were chosen as case studies. These samples were analyzed by means of optical microscopy, Cryo-scanning electron microscopy (SEM), SEM, and field emission scanning electron microscopy. Spodograms were obtained for BvLA and BgLA, which have high proportions of silicon, but no spodogram was obtained for SLA because of the low silicon content. Different types of phytoliths (specific cells, reservoirs of silica in plants) in the studied leaves were observed. These phytoliths maintained their form after calcination at temperatures in the 350-850°C range. Owing to the chemical composition of these ashes, they are of interest for use in cements and concrete because of their possible pozzolanic reactivity. However, the presence of significant amounts of K and Cl in the prepared ashes implies a limitation of their applications.

  17. Multivariate chemical mapping of pigments and binders in easel painting cross-sections by micro IR reflection spectroscopy.

    Science.gov (United States)

    Rosi, Francesca; Federici, Arianna; Brunetti, Brunetto G; Sgamellotti, Antonio; Clementi, Sergio; Miliani, Costanza

    2011-03-01

    Paintings are composed of superimposed layers of inorganic and organic materials (pigments and binders). Knowledge of the stratigraphic sequence of these heterogeneous layers is fundamental for understanding the artist's painting technique and for conservation issues. In this study, micro-IR mapping experiments in reflection mode have been carried out on cross-sections taken from simulations of ancient easel paintings. The objective was to locate both organic binders and inorganic pigments. Chemical maps have been re-constructed using the common approach based on the integration of specific infrared bands. However, owing to the complexity of painting materials, this approach is not always applicable when dealing with broad and superimposed spectral features and with reststrahlen or derivative-like bands resulting from acquisition in reflection mode. To overcome these limitations, principal-component analysis has been successfully used for the re-construction of the image, extracting the relevant information from the complex full spectral data sets and obtaining reliable chemical distributions of the stratigraphy materials. Different pigment-binder combinations have been evaluated in order to understand limitations and strengths of the approach. Finally, the method has been applied for stratigraphic characterization of a cross-section from a 17th century wooden sculpture identifying both the original paint layer and the several overpaintings constituting the complex stratigraphy.

  18. Application of Microwaves for Binder Content Assessment in Moulding Sands

    Directory of Open Access Journals (Sweden)

    Nowak D.

    2012-09-01

    Full Text Available The paper presents results of preliminary examinations on possibility of determining binder content in traditional moulding sands with the microwave method. The presented measurements were carried-out using a special stand, the so-called slot line. Binder content in the sandmix was determined by measurements of absorption damping Ad and insertion losses IL of electromagnetic wave. One of main advantages of the suggested new method of binder content measurement is short measuring time.

  19. 有机硅改性聚丙烯酸酯涂料印花粘合剂的制备%Preparation of silicone-modified polyacrylate binder for pigment printing

    Institute of Scientific and Technical Information of China (English)

    杨振; 朱建华; 王亚东; 权衡

    2011-01-01

    The pigment printing binder was prepared by modifying polyacrylate with octamethyl cyclotetrasiloxane (D4).The pre-polymerization time and dosage of silicone, catalyst and its dosage and dosage of vinyl trimethoxysilane (VTMS) were investigated.The results showed that an excellent silicone-modified polyacrylate emulsion with good application property could be obtained after the grafting modification of polyacrylate using 1.5%(on the weight of D4) of inorganic acid A as catalyst, 5% of D4 and VTMS (on the weight of polyacrylate) within 1.0%of VTMS (on the weight of D4), the pre-polymerization time was 180 min.%采用八甲基环四硅氧烷(D4)对聚丙烯酸酯进行改性,合成了涂料印花粘合剂.对有机硅预聚时间及用量、催化剂及用量、偶联剂[乙烯基三甲氧基硅烷(VTMS)]用量等进行研究.结果表明:无机酸A 1.5%(对D4质量)作催化剂,D4和VTMS用量5%(对聚丙烯酸酯质量),其中VTMS用量1.0%(对04质量),预聚180min后接枝改性聚丙烯酸酯,可得应用性能较好的有机硅改性聚丙烯酸酯乳液.

  20. Thermal debinding dynamics of novel binder system

    Institute of Scientific and Technical Information of China (English)

    周继承; 黄伯云; 张传福; 刘业翔

    2001-01-01

    The thermal debinding dynamics of newly developed binders for cemented carbides extrusion molding was studied. It is shown that the thermal debinding processes can be divided into two stages: low temperature region, in which the low molecular mass components (LMMCs) are removed; and high temperature region, in which the polymer components are removed. The rate of thermal debinding is controlled by diffusion mechanism. The thermal debinding activation energies were solved out by differential method and integral method. The results show that the addition of other components acted as a catalyzer can effectively decrease the activation energy of thermal debinding processes.

  1. Sustainable binders for concrete: A structured approach from waste screening to binder composition development

    NARCIS (Netherlands)

    Vinai, R.; Panagiotopoulou, C.; Soutsos, M.; Taxiarchou, M.; Zervaki, M.; Valcke, S.L.A.; Ligero, V.C.; Couto, S.; Gupta, A.; Pipilikaki, P.; Alvarez, I.L.; Coelho, D.; Branquinho, J.

    2015-01-01

    Worldwide, the building sector requires the production of 4 billion tonnes of cement annually, consuming more than 40% of global energy. Alkali activated “cementless” binders have recently emerged as a novel eco-friendly construction material with a promising potential to replace ordinary Portland c

  2. Evolution of geopolymer binders: a review

    Science.gov (United States)

    Nuruddin, M. F.; Malkawi, A. B.; Fauzi, A.; Mohammed, B. S.; Almattarneh, H. M.

    2016-06-01

    This study aimed to present the current state of research about the terminology, chemical reactions, mechanisms, and microstructure modelling of geopolymer binders. Modelling the structure of the geopolymerization products is essential for controlling the product properties. The currently available models have shown some limitations in determining the rate of geopolymerization and setting time of the gel. There is a need for deeper knowledge regarding the physicochemical analysis of geopolymer binders. Most of the available models have used pure material like metakaolin; however, the less pure materials are expected to have different mechanisms. The FTIR and MAS-NMR analysis are considered as effective tools in providing information on the molecular deviations during geopolymerization. However, XRD analysis is not effective because most of the changes take place in amorphous phases. Also, the role of the iron oxides and some of the other impurities still not clear where none of the previous method of investigation can be used to detect the molecular changes of the iron compounds. This issue is very relevant hence the iron oxides are existed in substantial amounts in most of the waste materials that are suitable to be used as geopolymer source materials.

  3. Mortar and concrete based on calcium sulphate binders

    NARCIS (Netherlands)

    Bakker, J.J.F.; Brouwers, H.J.H.

    2006-01-01

    In this study both hemi-hydrate and anhydrite are tested as calcium sulphate binders for structural mortar and concrete. The advantage of using calcium sulphates instead of cement as a binder is the fact that the production of calcium sulphate is more environmental friendly than that of cement. For

  4. 46 CFR 308.544 - Facultative binder, Form MA-315.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Facultative binder, Form MA-315. 308.544 Section 308.544 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Cargo Insurance Iii-Facultative War Risk Cargo Insurance § 308.544 Facultative binder, Form...

  5. An Open Challenge Problem Repository for Systems Supporting Binders

    Directory of Open Access Journals (Sweden)

    Amy Felty

    2015-07-01

    Full Text Available A variety of logical frameworks support the use of higher-order abstract syntax in representing formal systems; however, each system has its own set of benchmarks. Even worse, general proof assistants that provide special libraries for dealing with binders offer a very limited evaluation of such libraries, and the examples given often do not exercise and stress-test key aspects that arise in the presence of binders. In this paper we design an open repository ORBI (Open challenge problem Repository for systems supporting reasoning with BInders. We believe the field of reasoning about languages with binders has matured, and a common set of benchmarks provides an important basis for evaluation and qualitative comparison of different systems and libraries that support binders, and it will help to advance the field.

  6. Environmentally Friendly Geopolymeric Binders Made with Perlite

    Science.gov (United States)

    Erdogan, S. T.

    2011-12-01

    Production of Portland cement (PC), the ubiquitous binding material for construction works, is responsible for 5-10 % of all anthropogenic CO2 emissions. Nearly half of these emissions arise from the decomposition of calcareous raw materials, and the other half from kiln fuel combustion and cement clinker grinding operations. As such, PC production contributes significantly to global warming and climate change. Lately, there have been efforts to develop alternative binders with lower associated green house gas emissions. An important class of such binders is geopolymers, formed by activating natural or waste materials with suitable alkaline or acidic solutions. These binders have very low CO2 emissions from grinding of the starting material, and some from the production of the activating chemical. The total CO2 emission from carefully formulated mixtures can be as low as 1/5th - 1/10th of those of Portland cement concrete mixtures with comparable properties. While use of industrial wastes is environmentally preferable, the variability of their chemical compositions over time makes their use difficult. Use of natural materials depletes resources but can have more consistent properties and can be more easily accepted. Perlite is a volcanic aluminosilicate glass abundant in Turkey, China, Japan, the US and several EU countries. It has been used in its expanded form, for horticulture, for insulation, and for producing lightweight concrete. Turkish perlites contain more than 70 % SiO2, and have a SiO2/Al2O3 ratio of ~5.5. This study shows that ground perlite can be mixed with alkaline activators like sodium hydroxide or sodium silicate to yield mortars with strengths comparable to those of portland cement mortars. Strength gain is slower than with PC mixtures at room temperature but adequate ultimate strength can be achieved with curing at slightly elevated temperatures in 24 h or less. Since perlite is natural, perlite geopolymers can have environmental, energetic, and

  7. Development of a green binder system for paper products.

    Science.gov (United States)

    Flory, Ashley R; Vicuna Requesens, Deborah; Devaiah, Shivakumar P; Teoh, Keat Thomas; Mansfield, Shawn D; Hood, Elizabeth E

    2013-03-26

    It is important for industries to find green chemistries for manufacturing their products that have utility, are cost-effective and that protect the environment. The paper industry is no exception. Renewable resources derived from plant components could be an excellent substitute for the chemicals that are currently used as paper binders. Air laid pressed paper products that are typically used in wet wipes must be bound together so they can resist mechanical tearing during storage and use. The binders must be strong but cost-effective. Although chemical binders are approved by the Environmental Protection Agency, the public is demanding products with lower carbon footprints and that are derived from renewable sources. In this project, carbohydrates, proteins and phenolic compounds were applied to air laid, pressed paper products in order to identify potential renewable green binders that are as strong as the current commercial binders, while being organic and renewable. Each potential green binder was applied to several filter paper strips and tested for strength in the direction perpendicular to the cellulose fibril orientation. Out of the twenty binders surveyed, soy protein, gelatin, zein protein, pectin and Salix lignin provided comparable strength results to a currently employed chemical binder. These organic and renewable binders can be purchased in large quantities at low cost, require minimal reaction time and do not form viscous solutions that would clog sprayers, characteristics that make them attractive to the non-woven paper industry. As with any new process, a large-scale trial must be conducted along with an economic analysis of the procedure. However, because multiple examples of "green" binders were found that showed strong cross-linking activity, a candidate for commercial application will likely be found.

  8. Development of a green binder system for paper products

    Science.gov (United States)

    2013-01-01

    Background It is important for industries to find green chemistries for manufacturing their products that have utility, are cost-effective and that protect the environment. The paper industry is no exception. Renewable resources derived from plant components could be an excellent substitute for the chemicals that are currently used as paper binders. Air laid pressed paper products that are typically used in wet wipes must be bound together so they can resist mechanical tearing during storage and use. The binders must be strong but cost-effective. Although chemical binders are approved by the Environmental Protection Agency, the public is demanding products with lower carbon footprints and that are derived from renewable sources. Results In this project, carbohydrates, proteins and phenolic compounds were applied to air laid, pressed paper products in order to identify potential renewable green binders that are as strong as the current commercial binders, while being organic and renewable. Each potential green binder was applied to several filter paper strips and tested for strength in the direction perpendicular to the cellulose fibril orientation. Out of the twenty binders surveyed, soy protein, gelatin, zein protein, pectin and Salix lignin provided comparable strength results to a currently employed chemical binder. Conclusions These organic and renewable binders can be purchased in large quantities at low cost, require minimal reaction time and do not form viscous solutions that would clog sprayers, characteristics that make them attractive to the non-woven paper industry. As with any new process, a large-scale trial must be conducted along with an economic analysis of the procedure. However, because multiple examples of “green” binders were found that showed strong cross-linking activity, a candidate for commercial application will likely be found. PMID:23531016

  9. Dilatometric examination of moulds with plaster binder

    Directory of Open Access Journals (Sweden)

    M. Nadolski

    2011-01-01

    Full Text Available Investigations concerning thermal expansion of moulding materials with plaster binder have been performed for two mixture compositionsof Authors’ own design, as well as for the material used in jewellery industry under the Prima-Cast trade name, and for ThermoMold 1200moulding material. The results of dilatometric examinations of these materials, carried out within the temperature range from about 20°Cto 650°C by means of the DA-3 automatic dilatometer, have been compared. An analysis of this comparison has revealed that it is thematrix composition which is decisive for the magnitude of dimensional changes of moulds, and that applying components which do notexhibit polymorphic transformations reduces dimensional changes of a mould during its thermal treatment.

  10. Conducting Polymeric Materials

    DEFF Research Database (Denmark)

    Hvilsted, Søren

    2016-01-01

    The overall objective of this collection is to provide the most recent developments within the various areas of conducting polymeric materials. The conductivity of polymeric materials is caused by electrically charged particles, ions, protons and electrons. Materials in which electrons...

  11. Thermomechanical properties of bitumen modified with crumb tire rubber and polymeric additives

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, V.; Martinez-Boza, F.J.; Navarro, F.J.; Gallegos, C. [Departamento de Ingenieria Quimica, Universidad de Huelva, Campus del Carmen, 21071 Huelva (Spain); Perez-Lepe, A.; Paez, A. [Centro de Tecnologia, Repsol-YPF, Carretera de Extremadura, N-V, km 18, 28931 Mostoles-Madrid (Spain)

    2010-09-15

    In this paper, the influence of some additives on the rheological and technological properties of crumb rubber modified binders has been studied. The research has been mainly focused on the degree of bitumen modification, measured as the improvement of the mechanical properties, produced by the additives used, and the storage stability of these binders at high temperature. The experimental results obtained reveal that all the polymeric additives used yield an improvement in both rheological and technological properties of the binder. The storage instability of these binders has been associated to sedimentation processes of insoluble CR particles that strongly influence the mechanical properties of the binder. The additives and processing conditions selected in this study do not completely prevent problems associated with the poor stability of CRMBs during storage at high temperature. Nevertheless, the use of polyoctenamer, FT-wax or SBS-containing additives improves CRMB stability. In this sense, similar loss tangent values were found before and after hot storage of these binders. (author)

  12. Hardening kinetics investigation of alkali-activated binder by small amplitude oscillatory rheometry

    Science.gov (United States)

    Rieger, D.; Kullová, L.; Čekalová, M.; Kovářík, T.

    2017-01-01

    In this study, the rheological behavior of geopolymeric inorganic binder was determined. This binder was synthesized by alkaline activation of mixture, comprising calcined claystone powder and milled blast furnace slag. As an alkaline activator of hardening process, the potassium silicate solution was used. For the investigation of hardening kinetics, the strain controlled small amplitude oscillatory rheometry was used with strain of 0.01%. The reproducibility and versatility of this method is demonstrated for determination of hardening process evolution. The changes of loss tangent shape were studied in this experiment and applied for determination of gelation time. All experiments were conducted at isothermal conditions in temperature range 27-70°C and parallel plate geometry. The results indicate that reaction kinetics is directly depending on temperature. The hardening kinetics was mathematically described and these calculations were compared with self-contained experiment conducted at 2°C. This experiment is described in details and the results of gelation time measurements confirmed calculated data.

  13. Hyper-cross-linked, hybrid membranes via interfacial polymerization

    NARCIS (Netherlands)

    Raaijmakers, M.J.T.

    2015-01-01

    Hyper-cross-linked, hybrid membranes consist of covalent networks of alternating organic and inorganic, or biological groups. This thesis reports on the preparation of such hybrid networks via interfacial polymerization. The structure-property relationships of the hybrid networks depend strongly on

  14. Carbon nanotube reinforced metal binder for diamond cutting tools

    DEFF Research Database (Denmark)

    Sidorenko, Daria; Mishnaevsky, Leon; Levashov, Evgeny

    2015-01-01

    of grain size of the structural constituents of the binder, what in turn leads to the improved simultaneously hardness, Young modulus, plastic extension, bending strength and performances of the metallic binders. Comparing service properties of diamond end-cutting drill bits with and without MWCNT one......The potential of carbon nanotube reinforcement of metallic binders for the improvement of quality and efficiency of diamond cutting wheels is studied. The effect of multi-walled carbon nanotube (MWCNT) reinforcement on the mechanical properties i.e. hardness, Young modulus, strength and deformation...

  15. Cationic fluorinated polymer binders for microbial fuel cell cathodes

    KAUST Repository

    Chen, Guang

    2012-01-01

    Fluorinated quaternary ammonium-containing polymers were used as catalyst binders in microbial fuel cell (MFC) cathodes. The performance of the cathodes was examined and compared to NAFION ® and other sulfonated aromatic cathode catalyst binders using linear sweep voltammetry (LSV), impedance spectroscopy, and performance tests in single chamber air-cathode MFCs. The cathodes with quaternary ammonium functionalized fluorinated poly(arylene ether) (Q-FPAE) binders showed similar current density and charge transfer resistance (R ct) to cathodes with NAFION ® binders. Cathodes containing either of these fluorinated binders exhibited better electrochemical responses than cathodes with sulfonated or quaternary ammonium-functionalized RADEL ® poly(sulfone) (S-Radel or Q-Radel) binders. After 19 cycles (19 d), the power densities of all the MFCs declined compared to the initial cycles due to biofouling at the cathode. MFC cathodes with fluorinated polymer binders (1445 mW m -2, Q-FPAE-1.4-H; 1397 mW m -2, Q-FPAE-1.4-Cl; 1277 mW m -2, NAFION ®; and 1256 mW m -2, Q-FPAE-1.0-Cl) had better performance than those with non-fluorinated polymer binders (880 mW m -2, S-Radel; 670 mW m -2, Q-Radel). There was a 15% increase in the power density using the Q-FPAE binder with a 40% higher ion exchange capacity (Q-FPAE-1.4-H compared to Q-FPAE-1.0-Cl) after 19 cycles of operation, but there was no effect on the power production due to counter ions in the binder (Cl -vs. HCO 3 -). The highest-performance cathodes (NAFION ® and Q-FPAE binders) had the lowest charge transfer resistances (R ct) in fresh and in fouled cathodes despite the presence of thick biofilms on the surface of the electrodes. These results show that fluorinated binders may decrease the penetration of the biofilm and associated biopolymers into the cathode structure, which helps to combat MFC performance loss over time. © 2012 The Royal Society of Chemistry.

  16. Strength properties of moulding sands with chosen biopolymer binders

    Directory of Open Access Journals (Sweden)

    St.M. Dobosz

    2010-07-01

    Full Text Available The article presents the results of primary researches of the IV generation moulding sands, in which as the binders are used differentbiodegradable materials. The bending and the tensile strength of the moulding sands with polylactide, poly(lactic-co-glycolic acid,polycaprolactone, polyhydroxybutyrate and cellulose acetate as binders were measured. The researches show that the best strengthproperties have the moulding sands with polylactide as binder. It was proved that the tested moulding sands’ strength properties are goodenough for foundry practice.

  17. Ion conducting organic/inorganic hybrid polymers

    Science.gov (United States)

    Meador, Maryann B. (Inventor); Kinder, James D. (Inventor)

    2010-01-01

    This invention relates to a series of organic/inorganic hybrid polymers that are easy to fabricate into dimensionally stable films with good ion-conductivity over a wide range of temperatures for use in a variety of applications. The polymers are prepared by the reaction of amines, preferably diamines and mixtures thereof with monoamines with epoxy-functionalized alkoxysilanes. The products of the reaction are polymerized by hydrolysis of the alkoxysilane groups to produce an organic-containing silica network. Suitable functionality introduced into the amine and alkoxysilane groups produce solid polymeric membranes which conduct ions for use in fuel cells, high-performance solid state batteries, chemical sensors, electrochemical capacitors, electro-chromic windows or displays, analog memory devices and the like.

  18. NATO Advanced Study Institute on Ring-opening Metathesis Polymerization of Olefins and Polymerization of Alkynes

    CERN Document Server

    1998-01-01

    The first NATO Advanced Study Institute on Olefin Metathesis and Polymerization Catalysts was held on September 10-22, 1989 in Akcay, Turkey. Based on the fundamental research of RRSchrock, RGrubbs and K.B.Wagener in the field of ring opening metathesis polymerization (ROMP), acyclic diene metathesis (ADMET) and alkyne polymerization, these areas gained growing interest within the last years. Therefore the second NATO-ASI held on metathesis reactions was on Ring Opening Metathesis Po­ lymerization of Olefins and Polymerization of Alkynes on September 3-16, 1995 in Akcay, Turkey. The course joined inorganic, organic and polymer chemists to exchange their knowledge in this field. This volume contains the main and short lectures held in Akcay. To include ADMET reactions better into the title of this volume we changed it into: Metathesis Polymerization of Olefins and Alkyne Polymerization. This volume is addressed to research scientists, but also to those who start to work in the area of olefin metathesis and al...

  19. New initiation system for polymerization of acryl acid

    Institute of Scientific and Technical Information of China (English)

    LI Hai-pu; ZHONG Hong; CHEN Qi-yuan; YIN Zhou-lan

    2005-01-01

    The redox initiation system for polyacrylate sodium of high molecular mass was designed and its effect with varying component dosage on the degree of polymerization was investigated. The results show that the proper type and amount of inorganic salt, as well as amine initiator, are conductive to the increase of degree of polymerization. The fine ingredient of the initiation system is as follows:the dosages of amine, persulphate and inorganic salt are 0.75%, 0.10% and 1.00% by mass based on acryl acid respectively, the molar ratio of sulphite to the persulphate is 1:1. Under such conditions the degree of polyacrylate can reach 7.43×107 with a acceptable polymerization time for industrial production.

  20. Ion-Conducting Organic/Inorganic Polymers

    Science.gov (United States)

    Kinder, James D.; Meador, Mary Ann B.

    2007-01-01

    Ion-conducting polymers that are hybrids of organic and inorganic moieties and that are suitable for forming into solid-electrolyte membranes have been invented in an effort to improve upon the polymeric materials that have been used previously for such membranes. Examples of the prior materials include perfluorosulfonic acid-based formulations, polybenzimidazoles, sulfonated polyetherketone, sulfonated naphthalenic polyimides, and polyethylene oxide (PEO)-based formulations. Relative to the prior materials, the polymers of the present invention offer greater dimensional stability, greater ease of formation into mechanically resilient films, and acceptably high ionic conductivities over wider temperature ranges. Devices in which films made of these ion-conducting organic/inorganic polymers could be used include fuel cells, lithium batteries, chemical sensors, electrochemical capacitors, electrochromic windows and display devices, and analog memory devices. The synthesis of a polymer of this type (see Figure 1) starts with a reaction between an epoxide-functionalized alkoxysilane and a diamine. The product of this reaction is polymerized by hydrolysis and condensation of the alkoxysilane group, producing a molecular network that contains both organic and inorganic (silica) links. The silica in the network contributes to the ionic conductivity and to the desired thermal and mechanical properties. Examples of other diamines that have been used in the reaction sequence of Figure 1 are shown in Figure 2. One can use any of these diamines or any combination of them in proportions chosen to impart desired properties to the finished product. Alternatively or in addition, one could similarly vary the functionality of the alkoxysilane to obtain desired properties. The variety of available alkoxysilanes and diamines thus affords flexibility to optimize the organic/inorganic polymer for a given application.

  1. Upgrading mild gasification liquids to produce electrode binder pitch. Technical report, December 1, 1992--February 28, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Knight, R.A. [Institute of Gas Technology, Chicago, IL (United States); Banerjee, D. [Illinois Clean Coal Inst., Carterville, IL (United States)

    1993-05-01

    The objective of this program is to investigate the production of electrode binder pitch from mild gasification liquids. The IGT MILDGAS process pyrolyzes coal in a 1000{degree}--1500{degree}F (538{degree}--816{degree}C) fluidized/entrained bed to produce solid, gas, and liquid co-products. With Illinois coal, the 750{degree} F+ (400{degree}C+) distillation residue (crude pitch) comprises 40--70% of the MILDGAS liquids, representing up to 20 wt % of feed coal. The largest market for pitch made from coal liquids is the aluminum industry, which uses it to make carbon anodes for electrolytic furnaces. Traditionally, binder pitches have only been made from high-temperature coke-oven tars. In this project, crude pitch from the DOE-sponsored MILDGAS process research program is being modified by a flash thermocracking technique to achieve specifications typical of a binder pitch. A pitch thermocracking unit has been constructed for operation at 1200{degree}--1800{degree}F (650{degree}--982{degree}C). Atomization of the pitch at the thermocracker inlet is being examined as a method of optimizing the particle size of polymerized pitch components. With the production of cracked pitch samples, test electrodes will be fabricated using the best performing pitch samples and petroleum coke or calcined pitch coke filler.

  2. Biosynthetic inorganic chemistry.

    Science.gov (United States)

    Lu, Yi

    2006-08-25

    Inorganic chemistry and biology can benefit greatly from each other. Although synthetic and physical inorganic chemistry have been greatly successful in clarifying the role of metal ions in biological systems, the time may now be right to utilize biological systems to advance coordination chemistry. One such example is the use of small, stable, easy-to-make, and well-characterized proteins as ligands to synthesize novel inorganic compounds. This biosynthetic inorganic chemistry is possible thanks to a number of developments in biology. This review summarizes the progress in the synthesis of close models of complex metalloproteins, followed by a description of recent advances in using the approach for making novel compounds that are unprecedented in either inorganic chemistry or biology. The focus is mainly on synthetic "tricks" learned from biology, as well as novel structures and insights obtained. The advantages and disadvantages of this biosynthetic approach are discussed.

  3. Effects of binder addition on the mechanical properties of bulk Y-Ba-Cu-O superconductors

    Science.gov (United States)

    Seki, H.; Wongsatanawarid, A.; Kobayashi, S.; Ikeda, Y.; Murakami, M.

    2010-11-01

    We studied the effects of binder addition on the mechanical properties of bulk Y-Ba-Cu-O superconductors. We prepared YBa2Cu3Oy, Y2BaCuO5 powders and polyvinyl alcohol mixed with water as a binder. These raw materials were mixed, and the binder-added powders were pressed into pellets. The hardness of the green compacts with binder is higher than that without the binder. However, the hardness of green compacts with 8% binder is the same as that with 4% binder. The maximum compression strength of the precursor with binder is higher than that without binder. Equally, the maximum strength of the green compacts with 8% binder is higher than that with 4% binder. The differential thermal analysis measurements showed that the exothermic reaction due to the decomposition of the organic binder started at 550 °C and gradually proceeded with further heating. After de-binder treatment, BaCO3 powders were produced on the green compacts. The green compacts were subjected to melt-processing. We also measured trapped magnetic fields of binder-added bulk Y-Ba-Cu-O superconductors with a Hall probe scanning device. Trapped magnetic field of the bulk added with 4% is higher than that of the binder-free bulk. Hence, Y-Ba-Cu-O bulk with suitable amount of binder shows good influence for mechanical strength and trapped magnetic field.

  4. Haemodynamic and respiratory effects of an abdominal compression binder

    DEFF Research Database (Denmark)

    Toft, M.H.; Bulow, J.; Simonsen, L.

    2008-01-01

    In order to elucidate the circulatory and respiratory effects of a newly developed abdominal compression binder 25 healthy, normal weight subjects were studied. In supine position the central haemodynamics were measured and estimated with a Finapress device. Lower extremity venous haemodynamics...... with or without the abdominal compression binder. The results show that the compression binder significantly increases the venous volume in the lower extremities as showed by a reduction in the venous capacitance in the lower extremities and a reduction in the stroke volume and cardiac output, while it does...... not influence the pulmonary volumes. It is concluded that the applied abdominal binder significantly affects peripheral and central haemodynamics. It should therefore be used with caution when in the supine position for longer periods, as the pooling of blood it induces in the lower extremities may have...

  5. New BioCo binders containing biopolymers for foundry industry

    Directory of Open Access Journals (Sweden)

    B. Grabowska

    2013-01-01

    Full Text Available Possibilities of cross-linking of new polymer binders from the BioCo group, their hardening in moulding sands at the application of cross-linking agents both physical and chemical are presented. Their thermal stability was determined. It was proved, that moulding sands bound by the BioCo binders are characterised by the compression strength (Ruc of an order of 2 MPa, and the bending strength (Rug of 1 MPa, after 1 hour of a sample curing. The worked out BioCo binders are biodegradable and renewable in the part which was not completely burned. The investigated moulding sands with the BioCo binders are easily knocked out and have a good susceptibility for mechanical reclamation processes.

  6. Development of bio-sourced binder to metal injection moulding

    Science.gov (United States)

    Royer, Alexandre; Barrière, Thierry; Gelin, Jean-Claude

    2016-10-01

    In the MIM process the binder play the most important role. It provides fluidity of the feedstock mixture for injection molding and adhesion of the powder to keep the molded shape. The binder must provide strength and cohesion for the molded part, must be easy to be removed from the molded part, and must be the recyclable, environmentally friendly and economical ones. The goal of this study is to develop a binder environmentally friendly. For this, a study of formulation based on polyethylene glycol, because of is water debinding properties, was made. Polylactic acid and Polyhydroxyalkanoates were investigated as bio sourced polymers. The chemical, miscibility and rheological behavior of the binder formulation were investigated.

  7. Role of binder in the synthesis of titania membrane

    Indian Academy of Sciences (India)

    K S Seshadri; M Selvaraj; R Kesava Moorthy; K Varatharajan; M P Srinivasan; K B Lal

    2003-02-01

    The synthesis of titania membrane through sol–gel route involves hydrolysis of alkoxide, peptization of hydrous oxide of titanium to obtain a sol, adjustment of the sol viscosity by including a binder and filtration of the viscous sol through a microporous support, gelation and sintering to desired temperature. The binder plays an important role in that it not only helps in adjustment of sol viscosity but also helps in binding the sol particle with porous support. Here a comparative study on the role of different binders, viz. polyvinyl alcohol, polyethyleneimine, polyacrylamide, effect of their viscosity and surface tension effect on the morphology of the titania membrane is presented. The results show that among the three binders studied polyvinyl alcohol gave rise to membranes of desired characteristics when the sol viscosity was 0.08 pa.s.

  8. THE USE OF METAL PHOSPHATE BINDER AND SAND IN FOUNDRIES

    Directory of Open Access Journals (Sweden)

    I. E. Illarionov

    2013-01-01

    Full Text Available Some features of the use of mixtures of metal phosphate binder and management principles of their properties for production of castings of ferrous and non-ferrous metals and alloys were shown.

  9. Impact of Binder Composition on Inkjet Printing Paper

    Directory of Open Access Journals (Sweden)

    Yan Zhang

    2015-01-01

    Full Text Available This article is focused on the impact of different binder mixtures on the performances of paper surface and printability. The coating properties were studied with the chosen silica pigment, and the binder consisted of vinyl acetate copolymer and polyvinyl alcohol with different ratios, followed by the measurement of smoothness, whiteness, and surface strength. The inkjet image quality was assessed using water-based inks. The print density, dot gain, and line quality were analyzed. The results showed that the surface performance and printability were affected by the composition of the binder. With the decrease of vinyl acetate copolymer and the increase of polyvinyl alcohol, the surface smoothness and strength decreased, and the penetration and diffusion of the ink changed as well. When the binder mixture was used with proper ratio, a larger solid density, smaller dot gain, and higher definition can be achieved, which were better than using either one of them alone.

  10. Rheological Evaluation of Polymer Modiifed Asphalt Binders

    Institute of Scientific and Technical Information of China (English)

    WANG Lan; CHANG Chunqing

    2015-01-01

    The microstructure and dynamic rheological characteristics of asphalt containing different polymer modifiers (crumb rubber, styrene-butadiene-styrene and crumb rubber mix with styrene-butadiene-styrene) at mid and high service temperature levels were investigated by using scanning electron microscopy(SEM), dynamic shear rheometer(DSR) and repeat creep test. The main objective of the investigation was to rank the modifiers based on their effect on performance characteristics of asphalt under service conditions. To evaluate the effect of different modiifers on the viscoelastic response of asphalt, the temperature and frequency dependences of the dynamic viscoelastic properties were compared. The mid-temperature fatigue resistance and high-temperature rutting resistance of three polymer modiifed asphalts were evaluated to predict their ifeld performance in roads. Based on the current results, an improved rutting factor was proposed to determine the rutting resistance of asphalt pavements. In addition, the viscous stiffness (Gv), deifned as the reciprocal of viscous compliance, was used to evaluate the high-temperature deformation resistance of asphalt mixtures. The experimental results indicate that the asphalt containing crumb rubber only shows superior performance at mid and high service temperatures in all three modiifed asphalt binders due to the action of the crumb rubber.

  11. Realizing of Optimization of Binder Backfill Material Under Certain Strength with Fuzzy Sets

    Institute of Scientific and Technical Information of China (English)

    崔明义; 胡华

    2001-01-01

    The main factors deciding the compressive strength of binder backfill body are tailing density and binder dosage in binder backfill materials. Based on the antecedent of certain pulp density, the method of increasing the tailing density and reducing the binder dosage, or the manner of cutting down the tailing density and gaining the binder dosage are taken to guarantee the strength of backfill body. The problem that should be solved is how to determine the tailing density and the binder dosage rationally. This paper tries to realize the correct selection of the tailing density and the binder dosage in computer with the method of fuzzy mathematics.

  12. Novel Binders and Methods for Agglomeration of Ore

    Energy Technology Data Exchange (ETDEWEB)

    S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

    2006-12-31

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking. This project has identified several acid-resistant binders and agglomeration procedures that can be used for improving the energy efficiency of heap leaching, by preventing the ''ponding'' and ''channeling'' effects that currently cause reduced recovery and extended leaching cycle times. Methods have also been developed for iron ore

  13. Neutral hydrophilic cathode catalyst binders for microbial fuel cells

    KAUST Repository

    Saito, Tomonori

    2011-01-01

    Improving oxygen reduction in microbial fuel cell (MFC) cathodes requires a better understanding of the effects of the catalyst binder chemistry and properties on performance. A series of polystyrene-b-poly(ethylene oxide) (PS-b-PEO) polymers with systematically varying hydrophilicity were designed to determine the effect of the hydrophilic character of the binder on cathode performance. Increasing the hydrophilicity of the PS-b-PEO binders enhanced the electrochemical response of the cathode and MFC power density by ∼15%, compared to the hydrophobic PS-OH binder. Increased cathode performance was likely a result of greater water uptake by the hydrophilic binder, which would increase the accessible surface area for oxygen reduction. Based on these results and due to the high cost of PS-b-PEO, the performance of an inexpensive hydrophilic neutral polymer, poly(bisphenol A-co-epichlorohydrin) (BAEH), was examined in MFCs and compared to a hydrophilic sulfonated binder (Nafion). MFCs with BAEH-based cathodes with two different Pt loadings initially (after 2 cycles) had lower MFC performance (1360 and 630 mW m-2 for 0.5 and 0.05 mg Pt cm-2) than Nafion cathodes (1980 and 1080 mW m -2 for 0.5 and 0.05 mg Pt cm-2). However, after long-term operation (22 cycles, 40 days), power production of each cell was similar (∼1200 and 700-800 mW m-2 for 0.5 and 0.05 mg Pt cm-2) likely due to cathode biofouling that could not be completely reversed through physical cleaning. While binder chemistry could improve initial electrochemical cathode performance, binder materials had less impact on overall long-term MFC performance. This observation suggests that long-term operation of MFCs will require better methods to avoid cathode biofouling. © 2011 The Royal Society of Chemistry.

  14. Novel Binders and Methods for Agglomeration of Ore

    Energy Technology Data Exchange (ETDEWEB)

    S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

    2006-12-31

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking. This project has identified several acid-resistant binders and agglomeration procedures that can be used for improving the energy efficiency of heap leaching, by preventing the ''ponding'' and ''channeling'' effects that currently cause reduced recovery and extended leaching cycle times. Methods have also been developed for iron ore

  15. Inorganic pigments doped with tris(pyrazol-1-yl)borate lanthanide complexes: A photoluminescence study

    Energy Technology Data Exchange (ETDEWEB)

    Gheno, Giulia, E-mail: giulia.gheno@unive.it [Dipartimento di Scienze Molecolari e Nanosistemi, Università Ca’ Foscari di Venezia, Dorsoduro 2137, 30123 Venezia (Italy); Bortoluzzi, Marco; Ganzerla, Renzo [Dipartimento di Scienze Molecolari e Nanosistemi, Università Ca’ Foscari di Venezia, Dorsoduro 2137, 30123 Venezia (Italy); Enrichi, Francesco [CIVEN, Coordinamento Interuniversitario Veneto per le Nanotecnologie, Via delle Industrie 5, 30175 Marghera, Venezia (Italy)

    2014-01-15

    The inorganic pigments malachite, Egyptian blue, Ercolano blue and chrome yellow have been doped with the neutral homoleptic Ln(III) complex Ln(Tp){sub 3} (Ln=Eu, Tb; Tp=hydrotris(pyrazol-1-yl)borate) in the presence of arabic gum or acrylic emulsion as binders, in order to obtain photoluminescent materials of interest for cultural heritage restoration. The doped pigments have shown emissions associated to f–f transitions in the visible range upon excitation with UV light. Thermal and UV-light ageings have been carried out. In all the cases the photoluminescent behaviour is maintained, but in the cases of acrylic-based paints emission spectra and lifetimes are strongly influenced by thermal treatments. The choice of binder and pigments influences the photoluminescent behaviour of the corresponding film paints. -- Highlights: • Inorganic pigments doped with photoluminescent lanthanide complexes. • Hydrotris(pyrazol-1-yl)borate (Tp) as antenna-ligand for Eu(III) and Tb(III). • Emission associated to f–f transitions upon excitation with UV light. • Photoluminescence of paints influenced by the choice of binder and pigments. • Photoluminescence after ageing depending upon the type of binder.

  16. Organic-inorganic hybrid membranes in separation processes: a 10-year review

    Directory of Open Access Journals (Sweden)

    V. C. Souza

    2013-12-01

    Full Text Available In relation to some inorganic membranes, polymeric membranes have relatively low separation performance. However, the processing flexibility and low cost of polymers still make them highly attractive for many industrial separation applications. Polymer-inorganic hybrid membranes constitute an emerging research field and have been recently developed to improve the separation properties of polymer membranes because they possess properties of both organic and inorganic membranes such as good hydrophilicity, selectivity, permeability, mechanical strength, and thermal and chemical stability. The structures and processing of polymer-inorganic nanocomposite hybrid membranes, as well as their use in the fields of ultrafiltration, nanofiltration, pervaporation, gas separation and separation mechanism are reviewed.

  17. Aqueous Tape Casting Process with Styrene-acrylic Latex Binder

    Institute of Scientific and Technical Information of China (English)

    CUI Xue-min; OUYANG Shi-xi; HUANG Yong; YU Zhi-yong; ZHAO Shi-ke; WANG Chang-an

    2004-01-01

    A commercial styrene-acrylic latex binder has been investigated as a good binder for aqueous Al2O3 suspensions tape-casting process. This paper focuses on the forming film mechanism of latex binder, the rheological behaviors of the suspensions, physical properties of green tapes and drying process of aqueous slurries with latex binder system. The drying process of the alumina suspensions is shown to follow a two-stage mechanism (the first stage: evaporation controlled process; and the second stage: diffusion controlled process). During the drying stage of the suspensions, the compressive force presses the latex particles and makes them be distorted, which results in cross-linking structure in contacted latex particles of the solidified tapes.A smooth-surface and high-strength green tape was fabricated by aqueous tape casting with latex binder system. The results from the SEM images of the crossing section microstructure of green tapes show that the latex is a very suitable binder for aqueous tape casting.

  18. A novel screening system for claudin binder using baculoviral display.

    Directory of Open Access Journals (Sweden)

    Hideki Kakutani

    Full Text Available Recent progress in cell biology has provided new insight into the claudin (CL family of integral membrane proteins, which contains more than 20 members, as a target for pharmaceutical therapy. Few ligands for CL have been identified because it is difficult to prepare CL in an intact form. In the present study, we developed a method to screen for CL binders by using the budded baculovirus (BV display system. CL4-displaying BV interacted with a CL4 binder, the C-terminal fragment of Clostridium perfringens enterotoxin (C-CPE, but it did not interact with C-CPE that was mutated in its CL4-binding region. C-CPE did not interact with BV and CL1-displaying BV. We used CL4-displaying BV to select CL4-binding phage in a mixture of a scFv-phage and C-CPE-phage. The percentage of C-CPE-phage in the phage mixture increased from 16.7% before selection to 92% after selection, indicating that CL-displaying BV may be useful for the selection of CL binders. We prepared a C-CPE phage library by mutating the functional amino acids. We screened the library for CL4 binders by affinity to CL4-displaying BV, and we found that the novel CL4 binders modulated the tight-junction barrier. These findings indicate that the CL-displaying BV system may be a promising method to produce a novel CL binder and modulator.

  19. A Granule Model for Evaluating Adhesion of Pharmaceutical Binders

    Directory of Open Access Journals (Sweden)

    Hossein Orafai

    2003-10-01

    Full Text Available Granule capability is defined in terms of the strength of individual granule and friability of granulation batch to withstand breaking, abrasion and compactibility. Binder(s are added to perform the above properties .The common methods to asses their capability are to test crushing strength of the granules directly and to make statistical analysis and /or testing the friability of bulk granulation. In this work four substrate models including polymethylmetacrylate beads(PMMA,glass powder, acetaminophen, and para-aminobebzoic acid were chosen. The binder models were corn starch, gelatin, methylcellulose (MC and hydroxypropylmethylcellulose (HPMC. After massing the substrates with the binder solutions, discs were produced by the mean of the mold technique. The discs were dried and conditioned and then tested for tensile strength while the failed areas were scanned by SEM. Various granulations were made and the results of friability and crush strength were compared with the discs strength .The bond areas in the SEM showed the trend with the binder concentration .A comparison of the standard deviation shows that discs have much lower level of the strength than granules. The resulting discs showed a higher performance which is related to the stems for the discs shape .In conclusion, this method is a simple and is applicable to differentiate efficacy of binder under studies.

  20. PRELIMINARY TESTING OF NANOPARTICLE EFFECTIVENESS IN BINDER JETTING APPLICATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Bailey, Alta C [ORNL; Elliott, Amy M [ORNL; Basti, Mufeed M [ORNL

    2016-01-01

    Binder jetting works by selectively depositing a binder with an inkjet print head into layers of powdered material. Compared with other metal Additive Manufacturing (AM) processes, binder jetting has significant potential for near-term adoption in manufacturing environments due to its reliability and throughput. The Achilles heel of binder jetting, however, is the inability to produce fully dense, single-alloy materials. The lack of density in printed binder jet parts is strictly dictated by the packing factor of the powder feedstock. Adding nanoparticles during printing will not only increase the part s packing factor but may also serve as a sintering aid. This study focuses on the effect of both the binder and nanoparticles on the final part density. As an unintended consequence of high nanoparticle loading, printed parts underwent a significant increase in porosity during the curing process. This unintended consequence is the apparent result of the nanoparticles blocking the exit of the solvent vapor during the curing step. Additionally, nanoparticle use for densification is validated with SEM imagery.

  1. NOVEL BINDERS AND METHODS FOR AGGLOMERATION OF ORE

    Energy Technology Data Exchange (ETDEWEB)

    S.K. Kawatra; T.C. Eisele; J.A. Gurtler; C.A. Hardison; K. Lewandowski

    2004-04-01

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking.

  2. Evaluation of wettability of binders used in moulding sands

    Directory of Open Access Journals (Sweden)

    Hutera B.

    2007-01-01

    Full Text Available Binders used in moulding sand have the differential properties. One of the main parameters influencing on moulding sand properties is wettability of the sand grain by binding material. In the article some problems concerned with wettability evaluation have been presented and the importance of this parameter for quantity description of process occurring in system: binder- sand grain has been mentioned. The procedure of wetting angle measurement and operation of prototype apparatus for wettability investigation of different binders used in moulding sand have been described, as well as the results of wetting angle measurement for different binders at different conditions. The addition of little amount of proper diluent to binder results in the state of equilibrium reached almost immediately. Such addition can also reduce the value of equilibrium contact angle. The uniform distribution of binder on the surface of the sand grains and reducing of the required mixing time can be obtained. It has also a positive effect on the moulding sand strength.

  3. Development of an innovative bio-binder using Asphalt-rubber technology

    OpenAIRE

    2013-01-01

    This research work evaluates several parameters that can affect Asphalt Rubber (AR) binder performance and applies the AR technology to the development of an innovative renewable bio-binder that can fully and cost-effectively replace asphaltic bitumen derived from petroleum in flexible pavement construction. The “Binder Accelerated Separator” method was used to divide the constituents of the Asphalt Rubber and bio-binder (residual binder and swelled rubber). The physical and chemi...

  4. New functional polyether binders for low vulnerability propellants; Nouveaux liants polyethers fonctionnels pour propergols a faible vulnerabilite

    Energy Technology Data Exchange (ETDEWEB)

    Moreau-Friot, C.; Eck, G.; Jacob, G.; Chevalier, S.; Golfier, M.; Guengant, Y. [Groupe SNPE Propulsion/ Centre de Recherches du Boucher, 91 - Vert le Petit (France)

    2002-09-01

    HTPB propellants are widely used in solid rocket propellants. Their slow cook-off behaviour has to be improved because they lead to reactions type IV or V in the MURAT scale. Some work on propellants with polyether binders has shown that they lead to moderate reactions at slow cook-off tests. Work is based on the synthesis of functional polyethers. The objective consists in preparing a hydroxyl terminated polymer with a molecular weight between 1000 and 4000 g.mol{sup -1}, a low viscosity and a correct functionality. The binder, which is composed of a polymer, a plasticizer and a curing system, will be able to give mechanical properties in the use field (between -40 and +60 deg C). The polymer chosen to answer all those characteristics is composed of tetrahydrofuran and ethylene oxide. It is synthesised by cationic ring opening polymerisation in the presence of a diol and an adapted catalyst (BF{sub 3}OEt{sub 2}, HBF{sub 4}, SnCl{sub 4}/AT-..). First polymerizations were carried out of laboratory scale (from 30 g to 200 g). The study consists in varying the nature of catalysts the temperature, the solvent the purification methods and so on. The selected copolymer is chosen from many analysis results of the structure, particularly the average number molecular weight the hydroxyl rate, and the best alternative between a high molecular weight and a correct functionality. The behaviour of the propellant is also important because it will allow a widely scale synthesis or complementary laboratory work. A transfer has permitted to obtain a 10 kg scale. Its characteristics are the same that those of the product obtained at a laboratory scale. Propellants with polyether binder have been tested. The correct viscosity allows a high charge rate, which means energetic propellants. It also has to be noted that the binder does not crystallize. Those propellants have a good mechanistic behaviour in a large field of temperature. They also have a good behaviour at slow cook-off. The

  5. Recycling of blast furnace sludge by briquetting with starch binder: Waste gas from thermal treatment utilizable as a fuel.

    Science.gov (United States)

    Drobíková, Klára; Plachá, Daniela; Motyka, Oldřich; Gabor, Roman; Kutláková, Kateřina Mamulová; Vallová, Silvie; Seidlerová, Jana

    2016-02-01

    Steel plants generate significant amounts of wastes such as sludge, slag, and dust. Blast furnace sludge is a fine-grained waste characterized as hazardous and affecting the environment negatively. Briquetting is one of the possible ways of recycling of this waste while the formed briquettes serve as a feed material to the blast furnace. Several binders, both organic and inorganic, had been assessed, however, only the solid product had been analysed. The aim of this study was to assess the possibilities of briquetting using commonly available laundry starch as a binder while evaluating the possible utilization of the waste gas originating from the thermal treatment of the briquettes. Briquettes (100g) were formed with the admixture of starch (UNIPRET) and their mechanical properties were analysed. Consequently, they were subjected to thermal treatment of 900, 1000 and 1100°C with retention period of 40min during which was the waste gas collected and its content analysed using gas chromatography. Dependency of the concentration of the compounds forming the waste gas on the temperature used was determined using Principal component analysis (PCA) and correlation matrix. Starch was found to be a very good binder and reduction agent, it was confirmed that metallic iron was formed during the thermal treatment. Approximately 20l of waste gas was obtained from the treatment of one briquette; main compounds were methane and hydrogen rendering the waste gas utilizable as a fuel while the greatest yield was during the lowest temperatures. Preparation of blast furnace sludge briquettes using starch as a binder and their thermal treatment represents a suitable method for recycling of this type of metallurgical waste. Moreover, the composition of the resulting gas is favourable for its use as a fuel.

  6. Polymerization Using Phosphazene Bases

    KAUST Repository

    Zhao, Junpeng

    2015-09-01

    In the recent rise of metal-free polymerization techniques, organic phosphazene superbases have shown their remarkable strength as promoter/catalyst for the anionic polymerization of various types of monomers. Generally, the complexation of phosphazene base with the counterion (proton or lithium cation) significantly improves the nucleophilicity of the initiator/chain end resulting in highly enhanced polymerization rates, as compared with conventional metalbased initiating systems. In this chapter, the general features of phosphazenepromoted/catalyzed polymerizations and the applications in macromolecular engineering (synthesis of functionalized polymers, block copolymers, and macromolecular architectures) are discussed with challenges and perspectives being pointed out.

  7. Science Update: Inorganic Chemistry

    Science.gov (United States)

    Rawls, Rebecca

    1978-01-01

    This first in a series of articles describing the state of the art of various branches of chemistry reviews inorganic chemistry, including bioinorganic, photochemistry, organometallic, and solid state chemistries. (SL)

  8. Inorganic Coatings Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The inorganic Coatings Lab provides expertise to Navy and Joint Service platforms acquisition IPTs to aid in materials and processing choices which balance up-front...

  9. Data on the densification during sintering of binder jet printed samples made from water- and gas-atomized alloy 625 powders

    Directory of Open Access Journals (Sweden)

    Amir Mostafaei

    2017-02-01

    Full Text Available Binder jet printing (BJP is a metal additive manufacturing method that manufactures parts with complex geometry by depositing powder layer-by-layer, selectively joining particles in each layer with a polymeric binder and finally curing the binder. After the printing process, the parts still in the powder bed must be sintered to achieve full densification (A. Mostafaei, Y. Behnamian, Y.L. Krimer, E.L. Stevens, J.L. Luo, M. Chmielus, 2016; A. Mostafaei, E. Stevens, E. Hughes, S. Biery, C. Hilla, M. Chmielus, 2016; A. Mostafaei, Y. Behnamian, Y.L. Krimer, E.L. Stevens, J.L. Luo, M. Chmielus, 2016 [1–3]. The collected data presents the characterization of the as-received gas- and water-atomized alloy 625 powders, BJP processing parameters and density of the sintered samples. The effect of sintering temperatures on the microstructure and the relative density of binder jet printed parts made from differently atomized nickel-based superalloy 625 powders are briefly compared in this paper. Detailed data can be found in the original published papers by authors in (A. Mostafaei, J. Toman, E.L. Stevens, E.T. Hughes, Y.L. Krimer, M. Chmielus, 2017 [4].

  10. Novel hybrid polymeric materials for barrier coatings

    Science.gov (United States)

    Pavlacky, Erin Christine

    Polymer-clay nanocomposites, described as the inclusion of nanometer-sized layered silicates into polymeric materials, have been widely researched due to significant enhancements in material properties with the incorporation of small levels of filler (1--5 wt.%) compared to conventional micro- and macro-composites (20--30 wt.%). One of the most promising applications for polymer-clay nanocomposites is in the field of barrier coatings. The development of UV-curable polymer-clay nanocomposite barrier coatings was explored by employing a novel in situ preparation technique. Unsaturated polyesters were synthesized in the presence of organomodified clays by in situ intercalative polymerization to create highly dispersed clays in a precursor resin. The resulting clay-containing polyesters were crosslinked via UV-irradiation using donor-acceptor chemistry to create polymer-clay nanocomposites which exhibited significantly enhanced barrier properties compared to alternative clay dispersion techniques. The impact of the quaternary alkylammonium organic modifiers, used to increase compatibility between the inorganic clay and organic polymer, was studied to explore influence of the organic modifier structure on the nanocomposite material properties. By incorporating just the organic modifiers, no layered silicates, into the polyester resins, reductions in film mechanical and thermal properties were observed, a strong indicator of film plasticization. An alternative in situ preparation method was explored to further increase the dispersion of organomodified clay within the precursor polyester resins. In stark contrast to traditional in situ polymerization methods, a novel "reverse" in situ preparation method was developed, where unmodified montmorillonite clay was added during polyesterification to a reaction mixture containing the alkylammonium organic modifier. The resulting nanocomposite films exhibited reduced water vapor permeability and increased mechanical properties

  11. 'Green' reversible addition-fragmentation chain-transfer (RAFT) polymerization

    Science.gov (United States)

    Semsarilar, Mona; Perrier, Sébastien

    2010-10-01

    Reversible addition-fragmentation chain-transfer (RAFT) polymerization has revolutionized the field of polymer synthesis as a versatile tool for the production of complex polymeric architectures. As for all chemical processes, research and development in RAFT have to focus on the design and application of chemical products and processes that have a minimum environmental impact, and follow the principles of 'green' chemistry. In this Review, we summarize some of the green features of the RAFT process, and review the recent advances in the production of degradable polymers obtained from RAFT polymerization. Its use to modify biodegradable and renewable inorganic and organic materials to yield more functional products with enhanced applications is also covered. RAFT is a promising candidate for answering both the increasing need of modern society to employ highly functional polymeric materials and the global requirements for developing sustainable chemicals and processes.

  12. The addition effects of macro and nano clay on the performance of asphalt binder

    Directory of Open Access Journals (Sweden)

    M. El-Shafie

    2012-12-01

    Full Text Available The study was carried out to explore the addition effect of macro and organically modified nanoclay on the physical and mechanical properties of asphalt binders. Both macroclay and modified nanoclay were blended in an asphalt binder in various percentages (starting from 2% to 8%. The blended asphalt binders were characterized using kinematic viscosity (C.st, softening point (°C, and penetration and compared with anunmodified binder. The tensile strength of the asphalt binders was also tested as a function of clay types and content%. The results of the study indicated an increase in softening point; kinematics viscosity and decrease in binder penetration. The tensile strength of modified clay binders was enhanced at all percentages by a comparison with both macroclay and unmodified binders. The best improvements in the modified binders were obtained with 6% nanoclay.

  13. Interfacial reaction in squeeze cast SiCw/AZ91 composites with different binders

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The whisker/matrix interfaces in squeeze cast SiCw/AZ91 composites with different binders (silica binder, acid aluminum phosphate binder and without binder), were studied by transmission electron microscopy (TEM) and high resolution electron microscopy (HREM). The SiCw/AZ91 interface is very clean in the composites with no binders. For the composites with acid aluminum phosphate binders or silica binders, there exists fine discrete interfacial reaction products MgO at the interface, and a definite orientation relationship between MgO and SiCw. The interfacial reaction products MgO is unevenly distributed at different parts of the composite ingot with silica binder, and mainly distributed to the interface at the side part of the composite cylinder. While in the SiCw/AZ91 composite with acid aluminum phosphate binder, MgO particles are distributed evenly at the interface in almost all the parts of the composite ingot.

  14. Performance analysis of flexible DSSC with binder addition

    Science.gov (United States)

    Muliani, Lia; Hidayat, Jojo; Anggraini, Putri Nur

    2016-04-01

    Flexible DSSC is one of modification of DSSC based on its substrate. Operating at low temperature, flexible DSSC requires a binder to improve particles interconnection. This research was done to compare the morphology and performance of flexible DSSC that was produced with binder-added and binder-free. TiO2 powder, butanol, and HCl were mixed for preparation of TiO2 paste. Small amount of titanium isopropoxide as binder was added into the mixture. TiO2 paste was deposited on ITO-PET plastic substrate with area of 1x1 cm2 by doctor blade method. Furthermore, SEM, XRD, and BET characterization were done to analyze morphology and surface area of the TiO2 photoelectrode microstructures. Dyed TiO2 photoelectrode and platinum counter electrode were assembled and injected by electrolyte. In the last process, flexible DSSCs were illuminated by sun simulator to do J-V measurement. As a result, flexible DSSC containing binder showed higher performance with photoconversion efficiency of 0.31%.

  15. Performance analysis of flexible DSSC with binder addition

    Energy Technology Data Exchange (ETDEWEB)

    Muliani, Lia; Hidayat, Jojo; Anggraini, Putri Nur, E-mail: putri.nur.anggraini@gmail.com [Research Center for Electronics and Telecommunications Indonesian Institute of Sciences (PPET-LIPI) Kampus LIPI, Jl. Sangkuriang, Bandung 40135 (Indonesia)

    2016-04-19

    Flexible DSSC is one of modification of DSSC based on its substrate. Operating at low temperature, flexible DSSC requires a binder to improve particles interconnection. This research was done to compare the morphology and performance of flexible DSSC that was produced with binder-added and binder-free. TiO{sub 2} powder, butanol, and HCl were mixed for preparation of TiO{sub 2} paste. Small amount of titanium isopropoxide as binder was added into the mixture. TiO{sub 2} paste was deposited on ITO-PET plastic substrate with area of 1x1 cm{sup 2} by doctor blade method. Furthermore, SEM, XRD, and BET characterization were done to analyze morphology and surface area of the TiO{sub 2} photoelectrode microstructures. Dyed TiO{sub 2} photoelectrode and platinum counter electrode were assembled and injected by electrolyte. In the last process, flexible DSSCs were illuminated by sun simulator to do J-V measurement. As a result, flexible DSSC containing binder showed higher performance with photoconversion efficiency of 0.31%.

  16. Making Polymeric Microspheres

    Science.gov (United States)

    Rhim, Won-Kyu; Hyson, Michael T.; Chung, Sang-Kun; Colvin, Michael S.; Chang, Manchium

    1989-01-01

    Combination of advanced techniques yields uniform particles for biomedical applications. Process combines ink-jet and irradiation/freeze-polymerization techniques to make polymeric microspheres of uniform size in diameters from 100 to 400 micrometer. Microspheres used in chromatography, cell sorting, cell labeling, and manufacture of pharmaceutical materials.

  17. Applied bioactive polymeric materials

    CERN Document Server

    Carraher, Charles; Foster, Van

    1988-01-01

    The biological and biomedical applications of polymeric materials have increased greatly in the past few years. This book will detail some, but not all, of these recent developments. There would not be enough space in this book to cover, even lightly, all of the major advances that have occurred. Some earlier books and summaries are available by two of this book's Editors (Gebelein & Carraher) and these should be consul ted for additional information. The books are: "Bioactive Polymeric Systems" (Plenum, 1985); "Polymeric Materials In Medication" (Plenum, 1985); "Biological Acti vi ties of Polymers" (American Chemical Society, 1982). Of these three, "Bioacti ve Polymeric Systems" should be the most useful to a person who is new to this field because it only contains review articles written at an introductory level. The present book primarily consists of recent research results and applications, with only a few review or summary articles. Bioactive polymeric materials have existed from the creation of life...

  18. Nanocrystalline WC with non-toxic Fe-Mn binder

    Energy Technology Data Exchange (ETDEWEB)

    Siemiaszko, Dariusz [Military University of Technology, Department of Advanced Technology and Chemistry, ul. Gen. S. Kaliskiego 2, 00-908 Warsaw (Poland); Rosinski, Marcin; Michalski, Andrzej [Warsaw University of Technology, Department of Materials Science and Engineering, Woloska 141, 02-507 Warsaw (Poland)

    2010-05-15

    Cemented carbides, based on the tungsten carbide (WC), are very popular and useful in an industry. The most important metal us as a binder in this kind of materials is cobalt. It has many advantages as a binder: very good wettability, favourable solubility with WC and thermal conductivity similar to WC. However, cost of cobalt is very high because of its low natural resources. Cobalt is not also neutral for health. It is known as an allergen and same research shown that it could cause a cancer. This paper presents results of sintering the tungsten carbides with Fe-Mn alloys as the binders. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  19. In silico design of smart binders to anthrax PA

    Science.gov (United States)

    Sellers, Michael; Hurley, Margaret M.

    2012-06-01

    The development of smart peptide binders requires an understanding of the fundamental mechanisms of recognition which has remained an elusive grail of the research community for decades. Recent advances in automated discovery and synthetic library science provide a wealth of information to probe fundamental details of binding and facilitate the development of improved models for a priori prediction of affinity and specificity. Here we present the modeling portion of an iterative experimental/computational study to produce high affinity peptide binders to the Protective Antigen (PA) of Bacillus anthracis. The result is a general usage, HPC-oriented, python-based toolkit based upon powerful third-party freeware, which is designed to provide a better understanding of peptide-protein interactions and ultimately predict and measure new smart peptide binder candidates. We present an improved simulation protocol with flexible peptide docking to the Anthrax Protective Antigen, reported within the context of experimental data presented in a companion work.

  20. Permeability analysis for thermal binder removal from green ceramic bodies

    Science.gov (United States)

    Yun, Jeong Woo

    2007-12-01

    The permeability of unlaminated and laminated green tapes was determined as a function of binder content for binder removed by air oxidation. The tapes are comprised of barium titanate as the dielectric, and polyvinyl butyral and dioctyl phthalate as the main compoents of the binder mixture. The flow in porous media through the tapes was analyzed in terms of models for describing Knudsen, slip, and Poiseuille flow mechanisms. The characteristic pore size was determined to be 0.5-2 mum and thus Poiseuille flow was the dominant transport mechanism contributing to the flux. The permeability was then determined from Darcy's law for flow in porous media. The permeability was also determined from micro-structural attributes in terms of the specific surface, the pore fraction, and terms to account for tortuosity and constrictions. The permeability and adhesion strength of laminated green ceramic tapes were determined as a function of lamination conditions of time, temperature, and pressure.

  1. Modified polysaccharides as alternative binders for foundry industry

    Directory of Open Access Journals (Sweden)

    K. Kaczmarska

    2016-10-01

    Full Text Available Polysaccharides constitute a wide group of important polymers with many commercial applications, for example food packaging, fibres, coatings, adhesives etc. This review is devoted to the presentation of polysaccharide application in foundry industry. In this paper the selected properties of foundry moulding sand and core sand containing modified polysaccharides as binders are presented according to foreign literature data. Also, author’s own research about effect of using moulding sand binder consisting of modified polysaccharide (modified starch or its composition with non-toxic synthetic polymers are discussed. Based on technologies taken under consideration in this paper, it could be concluded that polysaccharides are suitable as an alternative for use as binder in foundry moulding applications.

  2. Inorganic UV filters

    Directory of Open Access Journals (Sweden)

    Eloísa Berbel Manaia

    2013-06-01

    Full Text Available Nowadays, concern over skin cancer has been growing more and more, especially in tropical countries where the incidence of UVA/B radiation is higher. The correct use of sunscreen is the most efficient way to prevent the development of this disease. The ingredients of sunscreen can be organic and/or inorganic sun filters. Inorganic filters present some advantages over organic filters, such as photostability, non-irritability and broad spectrum protection. Nevertheless, inorganic filters have a whitening effect in sunscreen formulations owing to the high refractive index, decreasing their esthetic appeal. Many techniques have been developed to overcome this problem and among them, the use of nanotechnology stands out. The estimated amount of nanomaterial in use must increase from 2000 tons in 2004 to a projected 58000 tons in 2020. In this context, this article aims to analyze critically both the different features of the production of inorganic filters (synthesis routes proposed in recent years and the permeability, the safety and other characteristics of the new generation of inorganic filters.

  3. Effect of crumb rubber on asphaltic binder chemistry and rheology

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Cicero de S.; Tome, Luisa G.A.; Sant' ana, Hosiberto B.; Soares, Jorge B.; Soares, Sandra A. [University Federal of Ceara, Fortaleza, CE (Brazil)

    2008-07-01

    The use of the crumb rubber (CR) from scraps tires to modify asphalt binders (AB) at high temperature can improve significantly the performance grade, but the storage stability can be influenced after the mix of AB and CR or polymer. The major concern of asphalt binder with polymer and CR blends is their lack of stability during prolonged storage at high temperatures. The tendency to phase separation under quiescent conditions appears as an important limitation for the practical use of these blends. After the RTFOT and PAV process, the binder conventional and modified was analyzed in a Fourier Transform Infrared spectrometer (FTIR) for chemical characterization. After aging in RTFOT, the AB presented a larger degradation compared to the CR of RABC and RABC commercial. So, the crumb rubber contributed to the binder stability, acting as an antioxidant in the aging process. The dynamic mechanical properties of CR modify asphalts binder before and after graft has been characterized by use of dynamic shear rheometer (DSR) or advances rheology expanded system (ARES) of Rheometric Scientific. The difference in the viscoelastic parameters between the top and the bottom sections of the tube was measured. It has been found that the added content of CR has great effect on the rheological properties of the AB and its high temperature performance. It also has been confirmed that the RABC sample showed larger storage stability compared to the sample RABC commercial observed with viscoelastic parameters. As a consequence, the use CR and aromatic oil can be considered a suitable alternative for modification of binder in pavement. (author)

  4. Influence of conductive additive on temperature susceptibility of asphalt binders

    Institute of Scientific and Technical Information of China (English)

    吴少鹏; 李波; 陈筝; 黄旭

    2008-01-01

    The effects of graphite on temperature susceptibility of asphalt binders were investigated by penetration test,Ring & Ball softening point test and viscosity test.And penetration index(IP),viscosity-temperature susceptibility(SVT),and penetration-viscosity numbers(NPV) were introduced to evaluate the effects.The results show that the penetration,softening point and viscosity of asphalt binder increase with the increase of content of graphite.This means that the addition of graphite makes asphalts stiffer.The results from IP,NPV and SVT show that temperature susceptibility is reduced by the addition of graphite.

  5. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Xun, Shidi; Battaglia, Vincent S.; Zheng, Honghe

    2017-05-16

    A family of carboxylic acid group containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  6. Influencing of foundry bentonite mixtures by binder activation

    Directory of Open Access Journals (Sweden)

    J. Beňo

    2015-10-01

    Full Text Available Although new moulding processes for manufacture of high quality castings have been developed and introduced into foundry practice in recent years, the green-sand moulding in bentonite mixture still remains the most widely used technology. Higher utility properties of bentonite binders are achieved through their activation. This contribution is aimed at finding a suitable activating agent. A number of sodium salts and MgO based agents has been chosen. In the framework of the experiment the swelling volume of chosen agents was tested and technological parameters of a bentonite mixture with a binder activated with the studied agents were determined.

  7. Microfluidics in inorganic chemistry.

    Science.gov (United States)

    Abou-Hassan, Ali; Sandre, Olivier; Cabuil, Valérie

    2010-08-23

    The application of microfluidics in chemistry has gained significant importance in the recent years. Miniaturized chemistry platforms provide controlled fluid transport, rapid chemical reactions, and cost-saving advantages over conventional reactors. The advantages of microfluidics have been clearly established in the field of analytical and bioanalytical sciences and in the field of organic synthesis. It is less true in the field of inorganic chemistry and materials science; however in inorganic chemistry it has mostly been used for the separation and selective extraction of metal ions. Microfluidics has been used in materials science mainly for the improvement of nanoparticle synthesis, namely metal, metal oxide, and semiconductor nanoparticles. Microfluidic devices can also be used for the formulation of more advanced and sophisticated inorganic materials or hybrids.

  8. Coatings for mechanical and chemical protection based on organic-inorganic sol-gel nanocomposites

    OpenAIRE

    Schmidt, Helmut K.; Kasemann, Reiner

    1994-01-01

    The sol-gel process opens the possibility of combining inorganic and organic units on a molecular or nanosized level. The flexible chemical approach of tailoring inorganic structures as well as organic polymeric structures in combination with the new concept of incorporation of nanoscaled metal oxide particles (in general boehmite) opens the possibility of achieving new multifunctional materials like extremely high scratch resistance, antisoiling properties, antifogging properties and corrosi...

  9. Coatings for mechanical and chemical protection based on organic-inorganic sol-gel nanocomposites

    OpenAIRE

    Schmidt, Helmut K.; Kasemann, Reiner

    1993-01-01

    The sol-gel process opens the possibility of combining inorganic and organic units on a molecular or nanosized level. The flexible chemical approach of tailoring inorganic structures as well as organic polymeric structures in combination with the new concept of incorporation of nanoscaled metal oxide particles (in general boehmite) opens the possibility of achieving new multifunctional materials like extremely high scratch resistance, antisoiling properties, antifogging properties and corrosi...

  10. Organic-inorganic Polymer Nano-hybrids Based on Sol-gel Reaction

    Institute of Scientific and Technical Information of China (English)

    Yoshiki; Chujo

    2007-01-01

    1 Results Nano-ordered composite materials consisting of organic polymers and inorganic materials have been attracting attention for the purpose of the creation of high-performance or high-functional polymeric materials. Especially,the word of "polymer hybrid" claims the blends of organic and inorganic components at nano-level dispersion. By using this idea,an enhancement of mechanical strength of organic polymers with silica particles is possible.High transparency of this material is another important ...

  11. Subnanometer-Diameter Wires Isolated in a Polymer Matrix by Fast Polymerization

    Science.gov (United States)

    Golden; DiSalvo; Frechet; Silcox; Thomas; Elman

    1996-08-09

    The preparation and analysis of inorganic-organic polymer nanocomposites consisting of inorganic nanowires and multiwire "cables" in a random-coil organic polymer host is reported. Dissolution of inorganic (LiMo3Se3)n wires in a strongly coordinating monomer, vinylene carbonate, and the use of a rapid polymerization in the presence of a cross-linking agent produce nanocomposites without phase separation. Polymerization of dilute solutions yields a material containing mostly (Mo3Se3(-))n mono- and biwires, 6 to 20 angstroms in diameter and 50 to 100 nanometers long. Polymerization of more concentrated liquid crystalline solutions yields a nanocomposite containing oriented multiwire cables, 20 to 40 angstroms in diameter and up to 1500 nanometers long, that display optical anisotropy and electrical conductivity.

  12. Bulk synthesis of polymer-inorganic colloidal clusters.

    Science.gov (United States)

    Perro, Adeline; Manoharan, Vinothan N

    2010-12-21

    We describe a procedure to synthesize colloidal clusters with polyhedral morphologies in high yield (liter quantities at up to 70% purity) using a combination of emulsion polymerization and inorganic surface chemistry. We show that the synthesis initially used for silica-polystyrene hybrid clusters can be generalized to create clusters from other inorganic and polymer particles. We also show that high yields of particular morphologies can be obtained by precise control of the inorganic seed particle size, a finding that can be explained using a hard-sphere packing model. These clusters can be further chemically modified for a variety of applications. Introducing a cross-linker leads to colloidal clusters that can be index matched in an appropriate solvent, allowing them to be used for particle tracking or optical studies of colloidal self-assembly. Also, depositing a thin silica layer on these colloids allows the surface properties to be controlled using silane chemistry.

  13. Polymeric AIE-based nanoprobes for biomedical applications: recent advances and perspectives

    Science.gov (United States)

    Zhang, Xiaoyong; Wang, Ke; Liu, Meiying; Zhang, Xiqi; Tao, Lei; Chen, Yiwang; Wei, Yen

    2015-07-01

    The development of polymeric luminescent nanomaterials for biomedical applications has recently attracted a large amount of attention due to the remarkable advantages of these materials compared with small organic dyes and fluorescent inorganic nanomaterials. Among these polymeric luminescent nanomaterials, polymeric luminescent nanomaterials based on dyes with aggregation-induced emission (AIE) properties should be of great research interest due to their unique AIE properties, the designability of polymers and their multifunctional potential. In this review, the recent advances in the design and biomedical applications of polymeric luminescent nanomaterials based on AIE dyes is summarized. Various design strategies for incorporation of these AIE dyes into polymeric systems are included. The potential biomedical applications such as biological imaging, and use in biological sensors and theranostic systems of these polymeric AIE-based nanomaterials have also been highlighted. We trust this review will attract significant interest from scientists from different research fields in chemistry, materials, biology and interdisciplinary areas.

  14. Effects of Fiber Finish on the Performance of Asphalt Binders and Mastics

    Directory of Open Access Journals (Sweden)

    Bradley J. Putman

    2011-01-01

    Full Text Available The objective of this study was to determine the effects of finishes applied to polyester fibers on the properties of asphalt binders and mastics. Asphalt binders were mixed with finishes that were extracted from the fibers, and mastics were also made with binder and fibers (with and without finish to isolate the effects of the finish. The results indicated that crude source plays a significant role in how the fiber finish affects the binders and mastics. Additionally different finishes had different effects on binder properties. The major finding of this study is that different polyester fibers, even from the same manufacturer, may not necessarily perform the same in an asphalt mixture. It is important to use fibers that are compatible with the particular asphalt binder that is being used because of the significance of the binder source on the interaction between the finish and the binder.

  15. Comparison of efficacy of the phosphate binders nicotinic acid and sevelamer hydrochloride in hemodialysis patients

    National Research Council Canada - National Science Library

    Ahmadi, Farrokhlagha; Shamekhi, Fatemeh; Lessan-Pezeshki, Mahbob; Khatami, Mohammad Reza

    2012-01-01

    ...), and must be controlled with the use of phosphate binders. Studies comparing the effects of sevelamer and nicotinic acid, both similar non-calcium and non-aluminum phosphate binders, are not available...

  16. Effects of binders on the performance of electric double-layer capacitors of carbon nanotube electrodes

    Institute of Scientific and Technical Information of China (English)

    LI Chensha; WANG Dazhi; ZHANG Baoyou; WANG Xiaofeng; CAO Maosheng; LIANG Ji

    2005-01-01

    Polarizable electrodes of electric double layer capacitor (EDLCs) were made from carhon nanotubes. Effects of different binders, which are phenolic resin (PF) and polytetrafluoroethylene (PTFE), on the properties of polarizable electrodes are studied. Results indicate that the microstructure, pore size distribution and specific capacitance of the electrodes with PTFE binder are superior to those electrodes with PF binder after carbonization. The suitable binder (PTFE) for carbon nanotubes electrodes is proposed.

  17. Polymeric bicontinuous microemulsions

    DEFF Research Database (Denmark)

    Bates, F.S.; Maurer, W.W.; Lipic, P.M.

    1997-01-01

    High molecular weight block copolymers can be viewed as macromolecular surfactants when blended with thermodynamically incompatible homopolymers. This Letter describes the formation of polymeric bicontinuous microemulsions in nurtures containing a model diblock copolymer and two homopolymers...

  18. Geological and Inorganic Materials.

    Science.gov (United States)

    Jackson, L. L.; And Others

    1989-01-01

    Presents a review focusing on techniques and their application to the analysis of geological and inorganic materials that offer significant changes to research and routine work. Covers geostandards, spectroscopy, plasmas, microbeam techniques, synchrotron X-ray methods, nuclear activation methods, chromatography, and electroanalytical methods.…

  19. Funky inorganic fibers

    NARCIS (Netherlands)

    de Wit, Patrick

    2017-01-01

    Inorganic porous hollow fibers (IPHF) are interesting for various applications that can benefit from a high surface-area-to-volume ratio. Examples include membranes, catalysts, electrodes, and combinations of these. The thesis starts with providing an overview of conceivable materials of which IPHF

  20. Oil-acrylic hybrid latexes as binders for waterborne coatings

    NARCIS (Netherlands)

    Hamersveld, van E.M.S.; Es, van J.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

    1999-01-01

    The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

  1. Haemodynamic and respiratory effects of an abdominal compression binder

    DEFF Research Database (Denmark)

    Toft, Mette Helene; Bülow, Jens; Simonsen, Lene

    2008-01-01

    In order to elucidate the circulatory and respiratory effects of a newly developed abdominal compression binder 25 healthy, normal weight subjects were studied. In supine position the central haemodynamics were measured and estimated with a Finapress device. Lower extremity venous haemodynamics w...

  2. 46 CFR 308.103 - Insured amounts under interim binder.

    Science.gov (United States)

    2010-10-01

    ... INSURANCE War Risk Hull and Disbursements Insurance § 308.103 Insured amounts under interim binder. (a... chapter. (b) Insurance risks. Insurance risks covered by the terms of the standard form of war risk hull... insurance additional to the war risk hull insurance provided under this subpart, and payment of claim......

  3. Multimodality and Immigrant Children (Response to Marni Binder)

    Science.gov (United States)

    Campano, Gerald; Low, David

    2011-01-01

    This response to Marni Binder reflects upon two examples of (im)migrant children's artwork and challenges the dominant notion that (im)migration experiences--and their subsequent portrayals--can be fit into neat slots. The authors position multimodal composing opportunities as affording children a vital instrument for deploying their full semiotic…

  4. Chelating polymeric membranes

    KAUST Repository

    Peinemann, Klaus-Viktor

    2015-01-22

    The present application offers a solution to the current problems associated with recovery and recycling of precious metals from scrap material, discard articles, and other items comprising one or more precious metals. The solution is premised on a microporous chelating polymeric membrane. Embodiments include, but are not limited to, microporous chelating polymeric membranes, device comprising the membranes, and methods of using and making the same.

  5. 40 CFR 427.30 - Applicability; description of the asbestos paper (starch binder) subcategory.

    Science.gov (United States)

    2010-07-01

    ... asbestos paper (starch binder) subcategory. 427.30 Section 427.30 Protection of Environment ENVIRONMENTAL... Asbestos Paper (Starch Binder) Subcategory § 427.30 Applicability; description of the asbestos paper (starch binder) subcategory. The provisions of this subpart are applicable to discharges resulting...

  6. PHOSPHATE BINDER THERAPY AND SERUM PHOSPHATE CONTROL FOLLOWING INITIATION OF HAEMODIALYSIS

    Directory of Open Access Journals (Sweden)

    Kimberly Farrand

    2012-06-01

    Serum P can be difficult to control following initiation of HD. Patients with elevated serum P were younger, and most had higher P binder use than the reference group. Overall, binder use was lower than in other studies of HD patients. Dietary education and higher doses of the most effective P binders may be needed to improve P management.

  7. Novel Binders and Methods for Agglomeration of Ore

    Energy Technology Data Exchange (ETDEWEB)

    S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

    2006-09-30

    Heap leaching is one of the methods being used to recover metal from low grade ore deposits. The main problem faced during heap leaching is the migration of fine grained particles through the heap, forming impermeable beds which result in poor solution flow. The poor solution flow leads to less contact between the leach solution and the ore, resulting in low recovery rates. Agglomeration of ore into coarse, porous masses prevents fine particles from migrating and clogging the spaces and channels between the larger ore particles. Currently, there is one facility in the United States which uses agglomeration. This operation agglomerates their ore using leach solution (raffinate), but is still experiencing undesirable metal recovery from the heaps due to agglomerate breakdown. The use of a binder, in addition to the leach solution, during agglomeration would help to produce stronger agglomerates that did not break down during processing. However, there are no known binders that will work satisfactorily in the acidic environment of a heap, at a reasonable cost. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. Increasing copper recovery in heap leaching by the use of binders and agglomeration would result in a significant decrease in the amount of energy consumed. Assuming that 70% of all the leaching heaps would convert to using agglomeration technology, as much as 1.64*10{sup 12} BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, which is equivalent to saving approximately 18% of the energy currently being used in leaching heaps. For every week a leach cycle was decreased, a savings of as much as 1.23*10{sup 11} BTU per week would result. This project has identified several acid-resistant binders and agglomeration procedures. These binders and experimental procedures will be able to be used for use in improving the energy efficiency of

  8. Investigation of the ageing effects on phenol-urea-formaldehyde binder and alkanol amine-acid anhydride binder coated mineral fibres

    DEFF Research Database (Denmark)

    Zafar, Ashar; Schjødt-Thomsen, Jan; Sodhi, R.;

    2013-01-01

    Phenol-Urea-Formaldehyde (PUF) binder coated mineral fibres' mechanical properties have been observed to degrade during ageing at elevated temperatures and humidity, while alkanol amine-acid anhydride binder based mineral fibres exhibited better ageing properties for same duration of ageing. X......-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) were employed to identify the chemical changes occurring in the PUF binder coated mineral fibres and alkanol amine-acid anhydride binder coated mineral fibres during that ageing. The samples were aged in a climate...... of amide, methylene ether and methylene linkages between urea groups present in the PUF binder. In the case of the alkanol amine-acid anhydride binder coated mineral fibres, both XPS and ToF-SIMS techniques consistently showed that the surface chemical composition of the organic components of the alkanol...

  9. Investigation of the ageing effects on phenol-urea-formaldehyde binder and alkanol amine-acid anhydride binder coated mineral fibres

    DEFF Research Database (Denmark)

    Zafar, Ashar; Schjødt-Thomsen, Jan; Sodhi, R.

    2013-01-01

    . Principal Component Analysis (PCA) was applied on the positive and negative ToF-SIMS spectra of the PUF binder coated mineral fibres, showing a decrease in the concentration of the nitrogen containing peaks during ageing. This decrease was attributed to the depolymerisation of the binder due to hydrolysis......Phenol-Urea-Formaldehyde (PUF) binder coated mineral fibres' mechanical properties have been observed to degrade during ageing at elevated temperatures and humidity, while alkanol amine-acid anhydride binder based mineral fibres exhibited better ageing properties for same duration of ageing. X......-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) were employed to identify the chemical changes occurring in the PUF binder coated mineral fibres and alkanol amine-acid anhydride binder coated mineral fibres during that ageing. The samples were aged in a climate...

  10. Recent progress of atomic layer deposition on polymeric materials.

    Science.gov (United States)

    Guo, Hong Chen; Ye, Enyi; Li, Zibiao; Han, Ming-Yong; Loh, Xian Jun

    2017-01-01

    As a very promising surface coating technology, atomic layer deposition (ALD) can be used to modify the surfaces of polymeric materials for improving their functions and expanding their application areas. Polymeric materials vary in surface functional groups (number and type), surface morphology and internal structure, and thus ALD deposition conditions that typically work on a normal solid surface, usually do not work on a polymeric material surface. To date, a large variety of research has been carried out to investigate ALD deposition on various polymeric materials. This paper aims to provide an in-depth review of ALD deposition on polymeric materials and its applications. Through this review, we will provide a better understanding of surface chemistry and reaction mechanism for controlled surface modification of polymeric materials by ALD. The integrated knowledge can aid in devising an improved way in the reaction between reactant precursors and polymer functional groups/polymer backbones, which will in turn open new opportunities in processing ALD materials for better inorganic/organic film integration and potential applications. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. ALTERNATIVE BINDERS TO BENTONITE FOR IRON ORE PELLETIZING : PART II : EFFECTS ON METALLURGICAL AND CHEMICAL PROPERTIES

    Directory of Open Access Journals (Sweden)

    Osman Sivrikaya

    2014-07-01

    Full Text Available This study was started to find alternative binders to bentonite and to recover the low preheated and fired pellet mechanical strengths of organic binders-bonded pellets. Bentonite is considered as a chemical impurity for pellet chemistry due to acid constituents (SiO2 and Al2O3. Especially addition of silica-alumina bearing binders is detrimental for iron ore concentrate with high acidic content. Organic binders are the most studied binders since they are free in silica. Although they yield pellets with good wet strength; they have found limited application in industry since they fail to give sufficient physical and mechanical strength to preheated and fired pellets. It is investigated that how insufficient preheated and fired pellet strengths can be improved when organic binders are used as binder. The addition of a slag bonding/strength increasing constituent (free in acidic contents into pellet feed to provide pellet strength with the use of organic binders was proposed. Addition of boron compounds such as colemanite, tincal, borax pentahydrate, boric acid together with organic binders such as CMC, starch, dextrin and some organic based binders, into magnetite and hematite pellet mixture was tested. After determining the addition of boron compounds is beneficial to recover the low pellet physical and mechanical qualities in the first part of this study, in this second part, metallurgical and chemical properties (reducibility - swelling index – microstructure – mineralogy - chemical content of pellets produced with combined binders (an organic binder plus a boron compound were presented. The metallurgical and chemical tests results showed that good quality product pellets can be produced with combined binders when compared with the bentonite-bonded pellets. Hence, the suggested combined binders can be used as binder in place of bentonite in iron ore pelletizing without compromising the pellet chemistry.

  12. Investigating the Possibility of Geopolymer to Produce Inorganic-Bonded Wood Composites for Multifunctional Construction Material – A Review

    Directory of Open Access Journals (Sweden)

    Siti Noorbaini Sarmin

    2014-09-01

    Full Text Available Wood-based composites are widely used in consumer products, either in structural or non-structural applications. One of the basic elements for wood-based composites is the binder itself. Recent years have seen great development and trends in the field of eco-friendly binders in wood-based composite. There have been many concerns on the effects of formaldehyde and volatile organic compounds (VOC released from wood-based products. Researchers have put lot of effort into developing environmental friendly products with enhanced sustainability. Binder materials with a focus on geopolymers (i.e., alumino-silicates are discussed in this publication. The development and utilization of geopolymeric binders is relatively new in the field of wood-based composites. Up to the present there has been insufficient information regarding the manufacturing conditions and properties of wood-nonwood composite materials prepared using a geopolymeric binder. This paper considers the background of geopolymer materials and the possibilities of producing inorganic-bonded wood composite using geopolymer.

  13. Polyacrylamide-based inorganic hybrid flocculants with self-degradable property

    Energy Technology Data Exchange (ETDEWEB)

    Wei, Xinfang [Materials and Metallurgical College, Northeastern University, Shenyang 110819 (China); Hebei Provincial Laboratory for Dielectric and Electrolyte Materials, Northeastern University at Qinhuangdao, Qinhuangdao 066004 (China); Tao, Junshi; Li, Mingzhi; Zhu, Bishan; Li, Xuan; Ma, Zhiyu; Zhao, Tingjie; Wang, Bingzhu; Suo, Biao [Hebei Provincial Laboratory for Dielectric and Electrolyte Materials, Northeastern University at Qinhuangdao, Qinhuangdao 066004 (China); Wang, Haiwang, E-mail: whwdbdx@126.com [Materials and Metallurgical College, Northeastern University, Shenyang 110819 (China); State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Hebei Provincial Laboratory for Dielectric and Electrolyte Materials, Northeastern University at Qinhuangdao, Qinhuangdao 066004 (China); Yang, Jun, E-mail: jyang@ipe.ac.cn [State Key Laboratory of Multiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Ye, Li, E-mail: yeli@iccas.ac.cn [Beijing National Laboratory for Molecular Sciences, Institute of Chemistry Chinese Academy of Sciences, Beijing 100190 (China); Qi, Xiwei, E-mail: qxw@mail.neuq.edu.cn [Materials and Metallurgical College, Northeastern University, Shenyang 110819 (China); Hebei Provincial Laboratory for Dielectric and Electrolyte Materials, Northeastern University at Qinhuangdao, Qinhuangdao 066004 (China)

    2017-05-01

    Polyacrylamide (PAM)-based inorganic hybrid materials are of great potential as flocculants in soil-liquid separation. Herein, we reported the design of inorganic soil-TiO{sub 2}-PAM hybrid materials using a unique process, which involved coating of titanium dioxide (TiO{sub 2}) nanoparticles on the surface of inorganic soils and subsequent polymerization of acrylamide (AM) on these nanoparticles under visible light. Inorganic soils including kaolin, bentonite, montmorillonite and diatomaceous earth were used to control the volume and to reduce the cost, and the TiO{sub 2} nanoparticles accelerated PAM degradation. The nanoparticles initiated AM polymerization directly under visible light, thus providing a facile strategy for the synthesis of new organic-inorganic hybrid flocculants. The obtained hybrid materials were characterized using Fourier transform infrared spectroscopy and transmission electron microscopy. The degradation of PAM initiated by UV irradiation exceeded 24% in 2 h, depending on its initial concentration. - Highlights: • A new polyacrylamide (PAM)-based inorganic hybrid flocculants with self-degradable property was developed. • TiO{sub 2} nanoparticles show a unique surface-initiated property under the condition of visible light. • We designed a facile strategy for the synthesis of inorganic soil@TiO{sub 2}@PAM hybrid materials.

  14. Effects of Fibre Additive on the High Temperature Property of Asphalt Binder

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Polyester fibre and floc xylogen fibre were used to prepare fibre-asphalt binder.An SHRP's dynamic shear rheometer (DSR) was employed to investigate the rheology charac teristics of fibre-asphalt binder, andthe flow resistance of binder was revealed by combining the rutting parameter, G * / sinδ.The results indicate that both kinds of fibres remarkably improved the high temperature pe~orrnance of asphalt binder.At the same time, the reinforcement mechanism of the fibres in the asphalt binder was also analyzed.

  15. Alkali-activated binders/geopolymer and an application to environmental engineering

    Directory of Open Access Journals (Sweden)

    Nida Chaimoon

    2014-06-01

    Full Text Available For environmental reason, new binders that can be used as Portland cement replacement materials are being needed. Recently, alkali-activated binders (AAB and geopolymer have found increasing interest. As several research reports have showed that the two new binders are likely to have high potential to be developed and become an alternative to OPC. However, confusion in the classification of both binders is still there. This paper reviews knowledge about AAB and geopolymer including historical background, reaction mechanisms and reaction products. The similarities and differences of both binders are discussed. The application to environmental engineering on hazardous waste management using stabilization/solidification is also described.

  16. Inorganic Analytical Chemistry

    DEFF Research Database (Denmark)

    Berg, Rolf W.

    The book is a treatise on inorganic analytical reactions in aqueous solution. It covers about half of the elements in the periodic table, i.e. the most important ones : H, Li, B, C, N, O, Na, Mg, Al, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Br, Sr, Mo, Ag, Cd, Sn, Sb, I, Ba, W,...

  17. Effect of modified humic acid binder on pelletisation of specularite concentrates

    Institute of Scientific and Technical Information of China (English)

    周友连; 张元波; 刘兵兵; 李光辉; 姜涛

    2015-01-01

    A modified humic acid (MHA) binder was tested as a substitute for bentonite to prepare qualified specularite pellets. The results show that there is stronger chemisorption between organic functional groups in MHA binder molecular and specularite particles, improving the green pellet strength. MHA binder has obvious effect on the strength and microstructure of preheated pellets due to the thermal decomposition of organic matters in MHA binder. Appropriately increasing preheating temperature or time can eliminate the adverse impact of organic matters on the preheated pellet strength. Compared with the bentonite pellets, the roasted pellets with MHA binder have a more compact microstructure, and the recrystallization of the Fe2O3 crystal grains is better. Consequently, under optimal conditions, 0.75%(mass fraction) MHA binder pellets have equal or better pellet strengths and contain 1.06%more total iron than 2%bentonite pellets. The testing results indicate that MHA binder is a promising and effective alternative to bentonite for the specularite pellets.

  18. Investigation of Ageing Effects on Organic Binders used for Mineral Wool Products

    DEFF Research Database (Denmark)

    Zafar, Ashar

    for the same duration of ageing. The main purpose of the present work is to examine the chemical changes occurring in the phenol-urea-formaldehyde binder based mineral fibres due to ageing, which cause deterioration of the mechanical properties of mineral wool products. This has been done using surface...... properties is the PUF binder, therefore further research work was performed to the pure PUF binder coatings to directly observe the ageing effects on the surface chemistry of the binder. High mass resolution ToFSIMS spectra of the pure PUF binder coatings confirmed that the depolymerisation of the cured......Phenol-Urea-Formaldehyde (PUF) binder based mineral wool products’ mechanical properties have been observed to degrade during ageing at elevated temperatures and humidity, while mineral wool products based on a newly developed alkanol amine-acid anhydride binder exhibited better ageing properties...

  19. Hygroscopicity -resistant mechanism of an α -starch based composite binder for dry sand molds and cores

    Directory of Open Access Journals (Sweden)

    Xia ZHOU

    2005-05-01

    Full Text Available Hygroscopicity-resistance of an α-starch based composite binder for dry sand molds (cores has been studied experimentally and theoretically. Focus is placed on the relationship between the hardening structure and humidity-resistance of the composite binder. The results show that the α-starch composite binder has good humidity-resistance due to its special complex structure. SEM observations illustrate that the composite binder consists of reticular matrix and a ball- or lump-shaped reinforcement phase, and the specific property of the binding membrane with heterogeneous structure is affected by humidity to a small extent. Based on the analyses on the interplays of different ingredients in the binder at hardening, the structure model and hygroscopicity-resistant mechanisms of the hardening composite binder were further proposed. Moreover, the reasons for good humidity-resistance of the composite binder bonded sand are well explained by the humidity-resistant mechanisms.

  20. Penetration and performance of isocyanate wood binders on selected wood species

    Directory of Open Access Journals (Sweden)

    Gruver, T. M., and

    2006-11-01

    Full Text Available The penetration and performance of polymeric diphenylmethane diisocyanate (pMDI wood binder was investigated according to three factors: substrate species (aspen, yellow-poplar, or southern yellow pine; anatomical bonding plane (radial or tangential; and moisture content (0%, 5%, or 12%. Compression shear block tests and fluorescence microscopy were used to examine bond performance and resin penetration. Statistically, each of the aforementioned factors impacted results. As moisture content increased, observed bond strengths and wood failure increased. Bond formation did not occur when the substrates were equilibrated to 0% moisture content, except for the radial bonding surfaces of pine, which did adhere. At 5 and 12% moisture contents, tangential bonding surfaces out-performed radial bonding surfaces. In terms of resin penetration, moisture content was clearly the most important variable. Little penetration was observed at 0% moisture content, while extensive resin penetration was observed at elevated moisture contents. Pine was the only wood species to exhibit resin flow through radial cells, possibly explaining the enhanced resin penetration depths observed in pine samples.

  1. Polyoxometalates: from inorganic chemistry to materials science.

    Science.gov (United States)

    Casañ-Pastor, Nieves; Gómez-Romero, Pedro

    2004-05-01

    Polyoxometalates have been traditionally the subject of study of molecular inorganic chemistry. Yet, these polynuclear molecules, reminiscent of oxide clusters, present a wide range of structures and with them ideal frameworks for the deployment of a plethora of useful magnetic, electroionic, catalytic, bioactive and photochemical properties. With this in mind, a new trend towards the application of these remarkable species in materials science is beginning to develop. In this review we analyze this trend and discuss two main lines of thought for the application of polyoxometalates as materials. On the one hand, there is their use as clusters with inherently useful properties on themselves, a line which has produced fundamental studies of their magnetic, electronic or photoelectrochemical properties and has shown these clusters as models for quantum-sized oxides. On the other hand, the encapsulation or integration of polyoxometalates into organic, polymeric or inorganic matrices or substrates opens a whole new field within the area of hybrid materials for harnessing the multifunctional properties of these versatile species in a wide variety of applications, ranging from catalysis to energy storage to biomedicine.

  2. Biodegradation of New Polymer Foundry Binders for the Example of the Composition Polyacrylic Acid/Starch

    Directory of Open Access Journals (Sweden)

    Beata Grabowska

    2011-04-01

    Full Text Available The investigations on the biodegradation process pathway of the new polymer binders for the example of water soluble compositionpolyacrylic acid/starch are presented in the hereby paper. Degradation was carried out in water environment and in a soil. Thedetermination of the total oxidation biodegradation in water environment was performed under laboratory conditions in accordance with the static water test system (Zahn-Wellens method, in which the mixture undergoing biodecomposition contained inorganic nutrient,activated sludge and the polymer composition, as the only carbon and energy source. The biodecomposition progress of the polymercomposition sample in water environment was estimated on the basis of the chemical oxygen demand (COD measurements and thedetermination the biodegradation degree, Rt, during the test. These investigations indicated that the composition polyacrylic acid/starchconstitutes the fully biodegradable material in water environment. The biodegradation degree Rt determined in the last 29th day of the test duration achieved 65%, which means that the investigated polymer composition can be considered to be fully biodegradable.During the 6 months biodegradation process of the cross-linked sample of the polymer composition in a garden soil several analysis ofsurface and structural changes, resulting from the sample decomposition, were performed. Those were: thermal analyses (TG-DSC,structural analyses (Raman spectroscopy and microscopic analyses (optical microscopy, AFM.

  3. Plasma polymerization by Softplasma

    DEFF Research Database (Denmark)

    Jiang, J.; Wu, Zhenning; Benter, Maike

    2008-01-01

    In the late 19th century, the first depositions - known today as plasma polymers, were reported. In the last century, more and more research has been put into plasma polymers. Many different deposition systems have been developed. [1, 2] Shi F. F. broadly classified them into internal electrode......, external electrode, and electrodeless microwave or high frequency reactors. [3] Softplasma™ is an internal electrode plasma setup powered by low frequenc~ gower supply. It was developed in late 90s for surface treatment of silicone rubber. [ ]- 5] It is a low pressure, low electron density, 3D homogenous...... plasma. In this study, we are presenting the surface modification"pf polymers by plasma polymerization using Softplasma™. Softplasma™ can be used for two major types of polymerization: polymerization of vinyl monomers, where plasma acts as initiator; chemical vapour deposition, where plasma acts...

  4. Inorganic Polymer Matrix Composite Strength Related to Interface Condition

    Directory of Open Access Journals (Sweden)

    John Bridge

    2009-12-01

    Full Text Available Resin transfer molding of an inorganic polymer binder was successfully demonstrated in the preparation of ceramic fiber reinforced engine exhaust valves. Unfortunately, in the preliminary processing trials, the resulting composite valves were too brittle for in-engine evaluation. To address this limited toughness, the effectiveness of a modified fiber-matrix interface is investigated through the use of carbon as a model material fiber coating. After sequential heat treatments composites molded from uncoated and carbon coated fibers are compared using room temperature 3-point bend testing. Carbon coated Nextel fiber reinforced geopolymer composites demonstrated a 50% improvement in strength, versus that of the uncoated fiber reinforced composites, after the 250 °C postcure.

  5. A binder phase of TiO based cermets

    Institute of Scientific and Technical Information of China (English)

    LI Qing-kui; GUAN Shao-kang; ZHONH Hui; LI Jiang; ZHONG Hai-yun

    2005-01-01

    A binder phase of TiO based cermets, a kind of imitated gold materials, was developed by adding active element Si to Fe-Cr alloy, and the related mechanisms were studied. The wettability, matching in thermodynamics and interfacial strength were investigated by the high temperature sessile drop method and element area scanning. The linear expansion coefficients of the materials were measured using TAH100 thermal analyzer. The results show that the wettability of Fe-Cr alloy on TiO are small, with a wetting angle about 90°. After adding some Si in Fe-Cr alloy, its wetting angle can be decreased to about 25°, the interfacial reactions can be prevented effectively and high interface binding can be formed. Fe-25%Cr-1.5%Si matches the thermal expansion coefficient of TiO, so it is a kind of relatively perfect binder for TiO based cermets imitated gold.

  6. Preparation of Flame Retardant Modified with Titanate for Asphalt Binder

    Directory of Open Access Journals (Sweden)

    Bo Li

    2014-01-01

    Full Text Available Improving the compatibility between flame retardant and asphalt is a difficult task due to the complex nature of the materials. This study explores a low dosage compound flame retardant and seeks to improve the compatibility between flame retardants and asphalt. An orthogonal experiment was designed taking magnesium hydroxide, ammonium polyphosphate, and melamine as factors. The oil absorption and activation index were tested to determine the effect of titanate on the flame retardant additive. The pavement performance test was conducted to evaluate the effect of the flame retardant additive. Oxygen index test was conducted to confirm the effect of flame retardant on flame ability of asphalt binder. The results of this study showed that the new composite flame retardant is more effective in improving the compatibility between flame retardant and asphalt and reducing the limiting oxygen index of asphalt binder tested in this study.

  7. Studies on organic binders with high infrared transparency*

    Institute of Scientific and Technical Information of China (English)

    Fu Cheng-Wu; Zhou Hao-Shen; Chen Ming-Qing

    2009-01-01

    This paper reports that two kinds of polymers with high infrared transparency and good mechanical and physical properties have been prepared. An internal standard method is used to evaluate the infrared transparency of the binders.The physical and mechanical properties of the binders are measured according to corresponding standards. The results show the absorbance of polymer A in 8-14 μm range is 26% that of the ethylene-vinyl acetate copolymer (EVA), and polymer B is 9% that of the EVA correspondingly. The film of polymer A shows good flexibility of above 1 mm, a hardness of grade 1, and adhesion of grade 2. The film of polymer B shows good flexibility of above 1 mm, a hardness of grade 1, and adhesion of grade 1.

  8. Characterization of low-purity clays for geopolymer binder formulation

    Science.gov (United States)

    Mostafa, Nasser Y.; Mohsen, Q.; El-maghraby, A.

    2014-06-01

    The production of geopolymer binders from low-purity clays was investigated. Three low-purity clays were calcined at 750°C for 4 h. The calcined clays were chemically activated by the alkaline solutions of NaOH and Na2SiO3. The compressive strength was measured as a function of curing time at room temperature and 85°C. The results were compared with those of a pure kaolin sample. An amorphous aluminosilicate polymer was formed in all binders at both processing temperatures. The results show that, the mechanical properties depend on the type and amount of active aluminum silicates in the starting clay material, the impurities, and the processing temperature.

  9. Characterization of low-purity clays for geopolymer binder formulation

    Institute of Scientific and Technical Information of China (English)

    Nasser Y.Mostafa; Q.Mohsen; A.El-maghraby

    2014-01-01

    The production of geopolymer binders from low-purity clays was investigated. Three low-purity clays were calcined at 750°C for 4 h. The calcined clays were chemically activated by the alkaline solutions of NaOH and Na2SiO3. The compressive strength was measured as a function of curing time at room temperature and 85°C. The results were compared with those of a pure kaolin sample. An amorphous aluminosilicate polymer was formed in all binders at both processing temperatures. The results show that, the mechanical properties depend on the type and amount of active aluminum silicates in the starting clay material, the impurities, and the processing temperature.

  10. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Battaglia, Vincent S.; Park, Sang -Jae

    2015-10-06

    A family of carboxylic acid groups containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. Triethyleneoxide side chains provide improved adhesion to materials such as, graphite, silicon, silicon alloy, tin, tin alloy. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  11. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Xun, Shidi; Battaglia, Vincent S.; Zheng, Honghe; Wu, Mingyan

    2015-07-07

    A family of carboxylic acid groups containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. Triethyleneoxide side chains provide improved adhesion to materials such as, graphite, silicon, silicon alloy, tin, tin alloy. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  12. Compressive strength and rheology of environmentally-friendly binders

    Directory of Open Access Journals (Sweden)

    Juan Manuel Lizarazo Marriaga

    2010-07-01

    Full Text Available Ordinary Portland cement production accounts for 9% of worldwide greenhouse gas emissions. This paper summarises the results of research aimed at developing environmentally-friendly binders which can be used as an alternative in civil construction, aimed at generating alternatives and sustainable materials. Mixes of the combination of granulated ground blast furnace slag, basic oxygen slag, cement kiln dust and plasterboard gypsum were used for optimising the binders, according to their compressive strength, to obtain 5 concrete mixtures made partially or completely with industrial waste. The results showed that the compressive strength of mixtures of Portland cement and industrial waste were suitable for different civil construction applications and, although mixtures formed entirely from industrial waste had a significant decrease in their compressive strength, the results sho- wed great potential for specific industrial applications. In addition to compressive strength, the rheological properties of these mixtures were determined for defining flow and workability characteristics.

  13. Effectiveness and cost-efficiency of phosphate binders in hemodialysis

    Directory of Open Access Journals (Sweden)

    Zsifkovits, Johannes

    2009-06-01

    Full Text Available Health political background: In 2006, the prevalence of chronic renal insufficiency in Germany was 91,718, of which 66,508 patients were on dialysis. The tendency is clearly growing. Scientific background: Chronic renal insufficiency results in a disturbance of the mineral balance. It leads to hyperphosphataemia, which is the strongest independent risk factor for mortality in renal patients. Usually, a reduction in the phosphate intake through nutrition and the amount of phosphate filtered out during dialysis are not sufficient to reduce the serum phosphate values to the recommended value. Therefore, phosphate binders are used to bind ingested phosphate in the digestive tract in order to lower the phosphate concentration in the serum. Four different groups of phosphate binders are available: calcium- and aluminium salts are the traditional therapies. Sevelamer and Lanthanum are recent developments on the market. In varying doses, all phosphate binders are able to effectively lower phosphate concentrations. However, drug therapies have achieved recommended phosphate levels in only 50 percent of patients during the last years. Research questions: How effective and efficient are the different phosphate binders in chronic renal insufficient patients? Methods: The systematic literature search yielded 1,251 abstracts. Following a two-part selection process with predefined criteria 18 publications were included in the assessment. Results: All studies evaluated conclude that serum phosphate, serum calcium and intact parathyroid hormone can be controlled effectively with all phosphate binders. Only the number of episodes of hypercalcaemia is higher when using calcium-containing phosphatebinders compared to Sevelamer and Lanthanum. Regarding the mortality rate, the cardiovascular artery calcification and bone metabolism no definite conclusions can be drawn. In any case, the amount of calcification at study start seems to be crucial for the further

  14. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Xun, Shidi; Battaglia, Vincent S.; Zheng, Honghe; Wu, Mingyan

    2017-08-01

    A family of carboxylic acid groups containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. Triethyleneoxide side chains provide improved adhesion to materials such as, graphite, silicon, silicon alloy, tin, tin alloy. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  15. Optimization of propellant binders - part I: statistical methodology

    Energy Technology Data Exchange (ETDEWEB)

    Niehaus, Michael; Greeb, Olaf [Fraunhofer Institut fuer Chemische Technologie, D-76327 Pfinztal (Germany)

    2004-06-01

    The development of new propellant binder systems requires the thermodynamic calculation of physico-chemical data as well as the adaption of the mechanical properties in order to achieve a reliable innerballistic profile of the resulting propellant. However, in most cases the mechanical data may not be easily predicted due to the complex interactions between the components of the binder like the resin, the curing agent or possibly plasticizers and curing catalysts. Therefore, this study focusses on the capability of the multivariate analysis on the prediction of the E-modulus of a system comprising nitrocellulose as well as GAP, Desmodur N100 and an energetic plasticiser. Using this method, an equation has been derived which, within the regression intervall, may be used for the prediction of the E-modulus as a function of the components mentioned above. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

  16. Mechanical Activation of Construction Binder Materials by Various Mills

    Science.gov (United States)

    Fediuk, R. S.

    2016-04-01

    The paper deals with the mechanical grinding down to the nano powder of construction materials. During mechanical activation a composite binder active molecules cement minerals occur in the destruction of the molecular defects in the areas of packaging and breaking metastable phase decompensation intermolecular forces. The process is accompanied by a change in the kinetics of hardening of portland cement. Mechanical processes during grinding mineral materials cause, along with the increase in their surface energy, increase the Gibbs energy of powders and, respectively, their chemical activity, which also contributes to the high adhesion strength when contacting them with binders. Thus, the set of measures for mechanical activation makes better use of the weight of components filled with cement systems and adjust their properties. At relatively low cost is possible to provide a spectacular and, importantly, easily repeatable results in a production environment.

  17. POLYMERIC SURFACTANT STRUCTURE

    Institute of Scientific and Technical Information of China (English)

    P.M. Saville; J.W. White

    2001-01-01

    Polymeric surfactants are amongst the most widespread of all polymers. In nature, proteins and polysaccharides cause self organization as a result of this surfactancy; in industry, polymeric surfactants play key roles in the food, explosives and surface coatings sectors. The generation of useful nano- and micro-structures in films and emulsions as a result of polymer amphiphilicity and the application of mechanical stress is discussed. The use of X-ray and neutron small angle scattering and reflectivity to measure these structures and their dynamic properties will be described. New results on linear and dendritic polymer surfactants are presented.

  18. Effect of base bitumen composition on asphalt rubber binder properties

    OpenAIRE

    Partl, M.N.; Ould-Henia, M.; Dumont, A.-G.

    2008-01-01

    The asphalt rubber blend properties are strongly related to its base components properties. The base bitumen composition is considered as a key factor influencing the final rheological properties of asphalt rubber binder. This paper describes results from a laboratory investigation of the interaction between crumb rubber and different composition bitumen according to the wet process. The bitumen composition is determined according to the SARA decomposition approac...

  19. SYNTHESIS AND CHARACTERIZATION OF STRUCTURALLY WELL-DEFINED POLYMER-INORGANIC HYBRID NANOPARTICLES VIA ATRP

    Institute of Scientific and Technical Information of China (English)

    Jie Bai; Jie-bin Pang; Kun-yuan Qiu; Yen Wei

    2002-01-01

    Atom transfer radical polymerization (ATRP) using cuprous chloride/2,2'-bipyridine (bipy) was applied to graft polymerization of styrene on the surface of silica nanoparticles to synthesize polymer-inorganic hybrid nanoparticles. 2-(4-Chloromethylphenyl) ethyltriethoxysilane (CTES) was immobilized on the surface of silica nanoparticles through condensation reaction of the silanol groups on silica with triethoxysilane group of CTES. Then ATRP of St was initiated by this surface-modified silica nanoparticles bearing benzyl chloride groups, and formed PSt graft chains on the surface of silica nanoparticles. The thickness of the graft chains increased with reaction time. End group analysis confirmed the occurrence of ATRP. Thermal analysis indicated that thermal stabilization of these resulting hybrid nanoparticles also increases with polymerization conversion. The results above show that this "grafting from" reaction could be used for the preparation of polymer-inorganic hybrid nanoparticles with controlled structure of the polymer's end groups.

  20. Structural and thermal properties of the Poly(styrene-ethyl acrylate) polymeric scintillation material for surface radioactive contamination measurement

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Ho Sang; Seo, Bum Kyoung; Lee, Kune Woo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2009-10-15

    Emulsion polymerization is a unique chemical process widely used to produce waterborne resins with various colloidal and physicochemical properties. These emulsion polymers find a wide range of applications such as synthetic rubbers, thermoplastics, coatings, adhesives, binders, rheological modifiers, plastics pigments, standards for the calibration of instruments, polymeric supports for the purification of proteins and drug delivery system, etc. Polystyrenes are widely employed as matrices in order to dope scintillating dyes for alpha and beta radiation sensors. For example, BC-400 (Bicron Direct Saint-Gobain, MA), a polyvinyltoluene-based scintillator doped with PPO and POPOP, is the best existing plastic scintillator for alpha particle detection. Using emulsion polymerization technique described in a previous communication, experiments have been performed to investigate the detection performance with the scintillators contents. In this paper, the properties of the polymer for radioactive contaminant measurement observed under various condition of polymerization and variously EA contents.

  1. Comparative Assessment of Stabilised Polybutadiene Binder under Accelerated Ageing

    Directory of Open Access Journals (Sweden)

    Luiz Felipe Cannaval Sbegue

    2016-04-01

    Full Text Available Polybutadiene elastomers are versatile materials, being employed at several applications from rocket propellant binder to adhesives and sealants. The elastomers derived from hydroxyl-terminated polybutadiene are usually stabilised with antioxidants to prevent degradation. In this study, a comparative assessment among 2,2’-methylene-bis (4-methyl-6-tert-butylphenol (AO2246, 2,6-di-tert-butyl-4-methylphenol (BHT, p-phenylenediamine (pPDA, and triphenylphosphine (TPP regarding stabilisation of hydroxyl-terminated polybutadiene binder under accelerated ageing (six months at 65 °C was carried out. Evaluation of antioxidants effectiveness was examined through Oxidation Induction time, sol/gel extraction, swelling and mechanical testing, dynamic mechanical analysis, and mass variation measurement. AO2246 yielded the best performance, meanwhile BHT was poorly protective. TPP acted as prooxidant, causing a severe degradation of the binder, and pPDA was not manageable to be assessed due to the lower curing degree of the resulted polyurethane.

  2. Preparation of carbon brushes with thermosetting resin binder

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Carbon brushes with a resin binder were prepared according to an industrial process and the effects of the molding pressure, grains size and cure temperature on the properties of brush samples were discussed. The results show that the bulk density,bending strength and Rockwell hardness increase, while resistivity decreases with increasing molding pressure. Cure temperature has much more influence on the properties of brushes than molding pressure and grains size. Isothermal differential scanning calorimetry(DSC) was used to estimate the degree of cure of resin binder and a novel method of using the true density to measure the degree of cure of resin binder was presented and discussed briefly. Based on optimal process parameters carbon brushes were manufactured, durability tests for brushes were carried out on an alternate current motor and scanning electron microscope(SEM)was adopted to observe the morphology of worn surface of brushes. The results show that a luster oxide film can be formed on the surface of brushes and their service life reaches 380 h.

  3. Comparative evaluation of an experimental binder in hot-mix asphalt: correlating the predicted performance of the binder with asphalt testing

    CSIR Research Space (South Africa)

    O'Connell, Johannes S

    2014-07-01

    Full Text Available The binder is an important constituent of an asphalt mix and it affects the overall performance of the mix, especially with regards to permanent deformation and fatigue cracking. The stiffest binder available from the Chevron refinery in the Western...

  4. Inorganic Analytical Chemistry

    DEFF Research Database (Denmark)

    Berg, Rolf W.

    The book is a treatise on inorganic analytical reactions in aqueous solution. It covers about half of the elements in the periodic table, i.e. the most important ones : H, Li, B, C, N, O, Na, Mg, Al, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Br, Sr, Mo, Ag, Cd, Sn, Sb, I, Ba, W......, Hg, Tl, Pb, Bi. The subjects of compound identification and bringing insoluble compounds in solution by alcaline melt digestion are also treated. A high number of small experiments are described....

  5. Polymerized and functionalized triglycerides

    Science.gov (United States)

    Plant oils are useful sustainable raw materials for the development of new chemical products. As part of our research emphasis in sustainability and green polymer chemistry, we have explored a new method for polymerizing epoxidized triglycerides with the use of fluorosulfonic acid. Depending on the ...

  6. Waterborne Polymeric Films.

    Science.gov (United States)

    1981-02-01

    Skydrol 500B is a fire resistant hydraulic fluid available from Monsanto and which is primarily tricresyl phosphate. In most cases, the above table...Makromol. Chem. 1979, 82 149.- 23. Ger. Offen 2,804,609; (8/9/79). Bayer AG. 24. Odian, G. "Principles of Polymerization; "McGraw-Hill Book Co.: New York

  7. Application of a bio-binder as a rejuvenator for wet processed asphalt shingles in pavement construction

    OpenAIRE

    2015-01-01

    This paper investigates the merits of application of bio-binder to enhance rheological properties of asphalt binder in the presence of wet processed recycled asphalt shingles (RAS). It will further examine the performance and workability of asphalt designed with and without a specified percentage of a bio-binder produced from swine manure and RAS. Bio-binder was introduced to liquid asphalt binder modified with four different percentages of RAS; the high and low temperature properties of each...

  8. Inorganic Crystal Structure Database (ICSD)

    Science.gov (United States)

    SRD 84 FIZ/NIST Inorganic Crystal Structure Database (ICSD) (PC database for purchase)   The Inorganic Crystal Structure Database (ICSD) is produced cooperatively by the Fachinformationszentrum Karlsruhe(FIZ) and the National Institute of Standards and Technology (NIST). The ICSD is a comprehensive collection of crystal structure data of inorganic compounds containing more than 140,000 entries and covering the literature from 1915 to the present.

  9. A Green Polymerization of Aspartic Acid for the Undergraduate Organic Laboratory

    Science.gov (United States)

    Bennett, George D.

    2005-01-01

    The green polymerization of aspartic acid carried out during an organic-inorganic synthesis laboratory course for undergraduate students is described. The procedure is based on work by Donlar Corporation, a Peru, Illinois-based company that won a Green Chemistry Challenge Award in 1996 in the Small Business category for preparing thermal…

  10. Surface-initiated Atom Transfer Radical Polymerization - a Technique to Develop Biofunctional Coatings

    DEFF Research Database (Denmark)

    Fristrup, Charlotte Juel; Jankova Atanasova, Katja; Hvilsted, Søren

    2009-01-01

    The initial formation of initiating sites for atom transfer radical polymerization (ATRP) on various polymer surfaces and numerous inorganic and metallic surfaces is elaborated. The subsequent ATRP grafting of a multitude of monomers from such surfaces to generate thin covalently linked polymer...

  11. Why is the electroanalytical performance of carbon paste electrodes involving an ionic liquid binder higher than paraffinic binders? A simulation investigation.

    Science.gov (United States)

    Ghatee, M H; Namvar, S; Zolghadr, A R; Moosavi, F

    2015-10-14

    Recently, carbon paste electrodes (CPE) fabricated using an ionic liquid (IL) binder have shown enhanced electroanalytical performance over conventional paraffinic binders. Molecular dynamics (MD) simulations of graphite mixed with ionic liquid and with paraffin binder can unravel the potential atomistic factors responsible for such enhancement. Based on an experimentally optimized binder/graphite mass ratio, which has been reported to be crucial for such a performance, comprehensive simulations (at 323 K) are performed with the ensembles involving an ionic liquid binder (1-butyl-3-methylimidazolium hexafluorophosphate, [C4mim]PF6) and a paraffin binder (n-C20H42) mixed with graphite comprising large-size hexagonal-shaped double graphene plates. Structural analysis indicates both binders form only a monolayer on the graphite surface, covering the surface locally by IL but all-encompassing by paraffin. With charged and uncharged graphite, the IL monolayer tends to cover mainly the graphite center without approaching the edge planes. On the contrary, a monolayer of the paraffin binder covers uniformly the center, near the center, and the edge planes. Cations and anions of the IL form well-defined two dimensional pentagonal matrixes with characteristic high adsorption energy, almost 2.4 times higher than paraffin adsorption. The cation and anion coordination ability of the IL is responsible for such a local distribution. The simulation of these phenomena under experimental conditions unravels strong two-dimensional coordination properties inherent to the ionic liquid when distributed over the graphite surface. This direct MD simulation comparison of the IL properties with an organic liquid counterpart, made for the first time, can be used to explain the high electroanalytical performance (electron transfer) of CPEs involving an IL binder over paraffin binders.

  12. Barium titanate tape properties for MLCC application using different binder systems

    Science.gov (United States)

    Yoon, Dang-Hyok

    Most of multilayer ceramic capacitor (MLCC) industries are currently using solvent-based slip systems, although water-based slips have been receiving increasing attention due to reduced health and environmental hazards. The current work focuses on two main fields to meet the challenges in MLCC processing in aqueous media. One is the comparison between water- and solvent-based slip systems using design of experiments (DOE). The other is the understanding of Ba2+ ion leaching behavior in water and its effect on tape properties. For the first part, twenty four kinds of BaTiO3 slips were investigated using three different binder systems: one solvent-based, and two water-based systems. Tape casting, sintering and characterization were conducted. Slip viscosity and tape strength of the green tape depended significantly on the binder type. It was possible to achieve a higher green density for water-based system than that for a solvent-based one. Most of the green body properties from solvent-based system depended on the ceramic powder. On the other hand, the dispersant was the most significant factor for the green body properties of two water-based systems. Sintered properties such as microstructure and dielectric permittivity for three systems depended significantly on the type of ceramic powder. An optimization was performed for each system by means of a scorecard. By choosing the optimum condition, comparable results were drawn for the water-based system compared to a solvent-based one for MLCC application. For the second part, the amount of Ba2+ ion leaching from BaTiO3 in water was determined by an EDTA titration method. The greater extent and the faster rate of Ba2+ leaching were found at the lower solution pH. The excess free barium ions expressed by means of the Ba/Ti ratio adversely affected most tape properties. To passivate BaTiO 3 surface from Ba2+ ion leaching in water, passivation agent layer (PAL) was formed by drying the slurry after adding a commercial

  13. Pharmaceutical equivalence of gabapentin tablets with various extragranular binders Pharmaceutical equivalence of gabapentin tablets with various extragranular binders

    Directory of Open Access Journals (Sweden)

    SWATI C. JAGDALE

    2010-06-01

    Full Text Available Gabapentin is a high-dose drug widely used as an oral anti-epilepticagent. Due to high crystalline and has poor compaction properties it is difficult to form tablets by direct compression. The aim of this study was to develop gabapentin tablets, pharmaceutically equivalent to the reference product Neurontin (marketed in USA. Gabapentin 800mg tablets were produced by wet granulation by keeping intragranular binder as well as its concentration constant and by changing with various extragranular binders with its concentration (A = PVPK 30, B = HPMC 15 cps, C = Kollidon VA 64, D =Klucel EXF.The tablet having no weight, thickness and hardness variation and having appropriate, friability as well as disintegration profile were coated with a 3% film coating solution .Seven formulations F1 (A in lower concentration F2 (A in higher concentration, F3 (B in lower concentration and F4 (B in higher concentration, F5 (C in lower concentration, F6 (C in higher concentration, F7 (D in lower concentration were formulated. Among them F6 demonstrated adequate hardness, friability, disintegration, uniformity of content, and total drug dissolution after 45minutes. The dissimilarity factor (f1 is 5.93 and the similarity factor (f2 is 67.85. So F6 was found to be equivalent to Neurontin.Gabapentin is widely used as an oral anti-epileptic agent. However, owing to its high crystallinity and poor compaction properties, it is difficult to form tablets of this drug by direct compression. The aim of this study was to develop gabapentin tablets, pharmaceutically equivalent to the brand-name pioneer product Neurontin® (marketed in USA. Gabapentin 800mg tablets were produced by wet granulation with a constant concentration of intragranular binder and a varying concentration of extragranular binders (A = polyvinylpyrrolidone K30, B = hydroxypropylmethylcellulose 15 cps, C = Kollidon VA64, D =Klucel EXF. The tablets that did not vary in weight, thickness or hardness and had

  14. Highly Branched Bio-Based Unsaturated Polyesters by Enzymatic Polymerization

    DEFF Research Database (Denmark)

    Nguyen, Hiep Dinh; Löf, David; Hvilsted, Søren

    2016-01-01

    A one-pot, enzyme-catalyzed bulk polymerization method for direct production of highly branched polyesters has been developed as an alternative to currently used industrial procedures. Bio-based feed components in the form of glycerol, pentaerythritol, azelaic acid, and tall oil fatty acid (TOFA....... This allows simple variations in the molar mass and structure of the polyester without premature gelation, thus enabling easy tailoring of the branched polyester structure. The postpolymerization crosslinking of the polyesters illustrates their potential as binders in alkyds. The formed films had good UV...... stability, very high water contact angles of up to 141° and a glass transition temperature that could be controlled through the feed composition....

  15. Bio-based alkyds by direct enzymatic bulk polymerization

    DEFF Research Database (Denmark)

    Nguyen, Hiep Dinh

    . Bio-based alkyds prepared from a combination of glycerol, and tall oil fatty acids, and azelaic acid by enzymatic polymerization show improved hydrophobicity and lower glass transition temperatures compared to an alkyd prepared from the same raw materials by a classical boiling method. The enzymatic...... to 500 grams of alkyds under inert atmosphere. This system has been used for preparation of a number of bio-based alkyds by classical cooking and provided a selection of physical properties as a function of diacid chain length. The synthesis set up was developed further to enhance reproducibility...... working on the coupling between reinforcement agents and the binder in alkyd coatings. For this purpose, two different types of silica particles were modified with rape seed oil fatty acids or tall oil fatty acids (TOFA-silica), respectively. Tests of TOFA-silica particles have demonstrated...

  16. Binder fraction reduction in non-ferrous metals concentrates briquetting process

    Directory of Open Access Journals (Sweden)

    M. Jodkowski

    2016-10-01

    Full Text Available The research results on a method of reducing the amount of binder applied during formation of metal concentrates are presented. Research was done on a model copper concentrate, which was mixed in assumed mass fraction with binder, as well as binder with addition of waste polyols. Such mixtures were formed and tested using static compressive strength, both immediately after forming and after the assumed seasoning times: 24, 96, 192 and 336 hours. The results confirm the possibility of binder dose lowering using high-efficiency system of binder dispersing with small addition of waste polyols and by homogeneous mixing of the binder with the material. In all examined cases increase in seasoning time influenced mechanical strength of the formed shapes advantageously.

  17. Briquetting of coal fines and sawdust. Part 1: binder and briquetting-parameters evaluations

    Energy Technology Data Exchange (ETDEWEB)

    D. Taulbee; D.P. Patil; Rick Q. Honaker; B.K. Parekh [University of Kentucky, Lexington, KY (United States). Center for Applied Energy Research

    2009-01-15

    Various technical and economic aspects relating to the briquetting of fine coal with sawdust have been evaluated with the results for two segments of that study presented here: binder and briquetting-parameter evaluations. Approximately 50 potential binder formulations were subjected to a series of screening evaluations to identify three formulations that were the most cost effective for briquetting fine coal with sawdust. Two of the binders, guar gum and wheat starch, were selected as most suitable for the pulverized coal market while the third formulation, lignosulfonate/lime, was targeted for the stoker market. Following binder selection, a number of briquetting parameters including binder and sawdust concentration, sawdust type, briquetting pressure and dwell time, coal and sawdust particle size, clay content, moisture content, and cure temperature and cure time were evaluated. Briquetting pressure and dwell time have the least impact while binder and sawdust concentrations, sawdust type, and curing conditions exerted the greatest influence on briquette quality. 7 refs.

  18. Influence of Mycotoxin Binders on the Oral Bioavailability of Doxycycline in Pigs.

    Science.gov (United States)

    De Mil, Thomas; Devreese, Mathias; De Saeger, Sarah; Eeckhout, Mia; De Backer, Patrick; Croubels, Siska

    2016-03-16

    Mycotoxin binders are feed additives that aim to adsorb mycotoxins in the gastrointestinal tract of animals, making them unavailable for systemic absorption. The antimicrobial drug doxycycline (DOX) is often used in pigs and is administered through feed or drinking water; hence, DOX can come in contact with mycotoxin binders in the gastrointestinal tract. This paper describes the effect of four mycotoxin binders on the absorption of orally administered DOX in pigs. Two experiments were conducted: The first used a setup with bolus administration to fasted pigs at two different dosages of mycotoxin binder. In the second experiment, DOX and the binders were mixed in the feed at dosages recommended by the manufacturers (= field conditions). Interactions are possible between some of the mycotoxin binders dosed at 10 g/kg feed but not at 2 g/kg feed. When applying field conditions, no influences were seen on the plasma concentrations of DOX.

  19. Development of water soluble binder systems for low pressure injection molding of alumina

    Energy Technology Data Exchange (ETDEWEB)

    Bakan, H.I.; Gunes, M. [TUBITAK-MRC Materials and Chemical Technologies Research Inst., Kocaeli (Turkey)

    2004-07-01

    Low pressure injection molding of alumina powder using a water-soluble binder system has been carried out successfully. The water-soluble based binder system consisted of poly (2-ethyl-2-oxaline), low density polyethylene and stearic acid. The critical powder loading of the binder-powder mixture was determined based on torque rheometry experiments. The rheological properties of the powder-binder mixture were investigated systematically. The binder system used provides satisfactory mixture stability, excellent mouldability and reasonably fast water leaching and thermal debinding rates. The water-soluble constituent, poly (2-ethyl-2-oxaline), was removed by leaching in convecting water at 60 C within 6 hour. The remaining binder constituents were thermally removed during heating to 450 C. Sintering of the parts was conducted at 1550 C for an hour in air. (orig.)

  20. Characteristics of low polymerization shrinkage flowable resin composites in newly-developed cavity base materials for bulk filling technique.

    Science.gov (United States)

    Nitta, Keiko; Nomoto, Rie; Tsubota, Yuji; Tsuchikawa, Masuji; Hayakawa, Tohru

    2017-06-23

    The purpose of this study was to evaluate polymerization shrinkage and other physical properties of newly-developed cavity base materials for bulk filling technique, with the brand name BULK BASE (BBS). Polymerization shrinkage was measured according to ISO/FDIS 17304. BBS showed the significantly lowest polymerization shrinkage and significantly higher depth of cure than conventional flowable resin composites (p<0.05). The Knoop hardness, flexural strength and elastic modulus of that were significantly lower than conventional flowable resin composites (p<0.05). BBS had the significantly greatest filler content (p<0.05). SEM images of the surface showed failure of fillers. The lowest polymerization shrinkage was due to the incorporation of a new type of low shrinkage monomer, which has urethane moieties. There were no clear correlations between inorganic filler contents and polymerization shrinkage, flexural strength and elastic modulus. In conclusion, the low polymerization shrinkage of BBS will be useful for cavity treatment in dental clinics.

  1. ALTERNATIVE BINDERS TO BENTONITE FOR IRON ORE PELLETIZING: PART I: EFFECTS ON PHYSICAL AND MECHANICAL PROPERTIES

    Directory of Open Access Journals (Sweden)

    Osman Sivrikaya

    2014-07-01

    Full Text Available The use of conventional bentonite binder is favorable in terms of mechanical and metallurgical pellet properties, however, because of its acid constituents bentonite is considered as impurity especially for iron ores with high acidic content. Therefore, alternative binders to bentonite have been tested. Organic binders are the most studied binders and they yield pellets with good wet strength; they fail in terms of preheated and fired pellet strengths. This study was conducted to investigate how insufficient pellet strengths can be improved when organic binders are used as binder. The addition of a low-melting temperature and slag bonding/strength increasing constituent (free in acidic contents into pellet feed was proposed. Addition of boron compounds such as colemanite, tincal, borax pentahydrate, boric acid together with organic binders such as CMC, starch, dextrin and some organic based binders, into iron oxide pellet was tested. Wet and thermally treated pellet physical-mechanical qualities (balling - moisture content - size - shape - drop number - compressive strengths - porosity - dustiness were determined. The results showed that good quality wet, dry, preheated and fired pellets can be produced with combined binders (an organic binder plus a boron compound when compared with bentonite-bonded pellets. While organic binders provided sufficient wet and dry pellet strengths, the boron compounds provided the required preheated and fired pellet strengths at even lower firing temperature. Especially, the contribution of boron compound addition is most pronounced for hematite pellets which do not have strengthening mechanism through oxidation like magnetite pellets during firing. Therefore, addition of boron compound is beneficial to recover the low physical-mechanical qualities of pellets produced with organic binders through slag bonding mechanism. Furthermore, lowering the firing temperature thanks to low-melting boron compounds will be cost

  2. Preparation of Composite Inorganic Polymer Coagulant-Polymeric Ferric Silicate Containing Boron (PFSSB) and Micropolluted Raw Water Treatment%新型复合无机高分子混凝剂——含硼聚硅酸硫酸铁( PFSSB)的制备及处理微污染水源水的研究

    Institute of Scientific and Technical Information of China (English)

    于瑞莲; 胡恭任

    2011-01-01

    含硼聚硅酸硫酸铁( PFSSB)混凝剂具有高效、适用范围广、无毒、适用性强等特点.用水玻璃、硫酸铁和硼砂为原料,SiO2浓度在3.0%,活化pH =2和活化时间1h等工艺条件下制取含硼聚硅酸硫酸铁(PFSSB)混凝剂.制备PFSSB混凝剂的优化条件为Fe3+及SiO2和B的摩尔比为1:2:0.3,最佳碱化度为0.2.含硼聚硅酸硫酸铁(PFSSB)混凝剂处理微污染水源水的最佳投药量为2mL,混凝时间为40min,pH范围为6~8.%The polymeric ferric silicate containing boron ( PFSSB ) is of high efficiency, wide application scope, not poisonous, strong adaptability etc. With water glass, ferric sulfate and borax as raw material, the polymeric ferric silicate containing boron (PFSSB) is prepared under the parameters of 3. 0% concentration of SiO2, activating at pH =2 for 1 h. The optimal condition for PFSSB preparation is n( Fe):n( SiO2): n( B ) = 1:2:0.3, the alkalization degree as 0. 2. The dosage of polymeric ferric silicate containing boron ( PFSSB) for handling the micropolluted raw water is to 2mL, time of coagulating is 40min, the scope of pH is 6~8.

  3. Curing mechanism of flexible aqueous polymeric coatings.

    Science.gov (United States)

    Irfan, Muhammad; Ahmed, Abid Riaz; Dashevskiy, Andriy; Kolter, Karl; Bodmeier, Roland

    2017-02-25

    The objective of this study was to explain curing phenomena for pellets coated with a flexible polymeric coating based on poly(vinyl acetate) (Kollicoat(®) SR 30D) with regard to the effect of starter cores, thickness of drug layer, adhesion of coating to drug-layered-cores as well as coating properties. In addition, appropriate approaches to eliminate the curing effect were identified. Sugar or MCC cores were layered with the model drugs carbamazepine, theophylline, propranolol HCl, tramadol HCl and metoprolol HCl using HPMC (5 or 25% w/w, based on drug) as a binder. Drug-layered pellets were coated with Kollicoat(®) SR 30D in a fluidized bed coater using TEC (10% w/w) as plasticizer and talc (35-100% w/w) as anti-tacking agent. Drug release, pellet properties (morphology, water uptake-weight loss and osmolality) and adhesion of the coating to the drug layer were investigated as a function of curing at 60 °C or 60 °C/75% RH for 24 h. The film formation of the aqueous dispersion of Kollicoat(®) SR 30D was complete, and therefore, a strong curing effect (decrease in drug release) at elevated temperature and humidity (60 °C/75% RH) could not be explained by the well-known hydroplasticization and the further gradual coalescence of the colloidal polymer particles. According to the provided mechanistic explanation, the observed curing effect was associated with 1) high flexibility of coating, 2) adhesion between coating and drug layer, 3) water retaining properties of the drug layer, and 4) osmotically active cores. Unwanted curing effects could be minimized/eliminated by the addition of talc or/and pore-forming water soluble polymers in the coating, increasing binder amount or applying an intermediate coating, by increasing the thickness of drug layer or using non-osmotic cores. A new insight into curing phenomena mainly associated with the adhesion between drug layer and coating was provided. Appropriate approaches to avoid unwanted curing effect were identified.

  4. Selective inorganic thin films

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, M.L.F.; Weisenbach, L.A.; Anderson, M.T. [Sandia National Laboratories, Albuquerque, NM (United States)] [and others

    1995-05-01

    This project is developing inorganic thin films as membranes for gas separation applications, and as discriminating coatings for liquid-phase chemical sensors. Our goal is to synthesize these coatings with tailored porosity and surface chemistry on porous substrates and on acoustic and optical sensors. Molecular sieve films offer the possibility of performing separations involving hydrogen, air, and natural gas constituents at elevated temperatures with very high separation factors. We are focusing on improving permeability and molecular sieve properties of crystalline zeolitic membranes made by hydrothermally reacting layered multicomponent sol-gel films deposited on mesoporous substrates. We also used acoustic plate mode (APM) oscillator and surface plasmon resonance (SPR) sensor elements as substrates for sol-gel films, and have both used these modified sensors to determine physical properties of the films and have determined the sensitivity and selectivity of these sensors to aqueous chemical species.

  5. Structural crystallography of inorganic oxysalts

    CERN Document Server

    Krivovichev, Sergey V

    2009-01-01

    Inorganic oxysalts are chemical compounds that contain oxygen - the most abundant element in the Earth's core. This book is the first systematic survey of structures of inorganic oxysalts considered from the viewpoint of modern scientific methods of description and visualisation of complex atomic arrangements.

  6. Environmentally-Friendly Geopolymeric Binders Made with Silica

    Science.gov (United States)

    Erdogan, S. T.

    2013-12-01

    Portland cement (PC) is the ubiquitous binding material for constructions works. It is a big contributor to global warming and climate change since its production is responsible for 5-10 % of all anthropogenic CO2 emissions. Half of this emission arises from the calcination of calcareous raw materials and half from kiln fuel burning and cement clinker grinding. Recently there have been efforts to develop alternative binders with lower greenhouse gas emissions. One such class of binders is geopolymers, formed by activating natural or waste materials with suitable alkaline or acidic solutions. These binders use natural or industrial waste raw materials with a very low CO2 footprint from grinding of the starting materials, and some from the production of the activating chemicals. The total CO2 emissions from carefully formulated mixtures can be as low as 1/10th - 1/5th of those of PC concrete mixtures with comparable properties. While use of industrial wastes as raw materials is environmentally preferable, the variability of their chemical compositions over time renders their use difficult. Use of natural materials depletes resources but can have more consistent properties and can be more easily accepted. Silica sand is a natural material containing very high amounts of quartz. Silica fume is a very fine waste from silicon metal production that is mostly non-crystalline silica. This study describes the use of sodium hydroxide and sodium silicate solutions to yield mortars with mechanical properties comparable to those of portland cement mortars and with better chemical and thermal durability. Strength gain is slower than with PC mixtures at room temperature but adequate ultimate strength can be achieved with curing at slightly elevated temperatures in less than 24 h. The consistency of the chemical compositions of these materials and their abundance in several large, developing countries makes silica attractive for producing sustainable concretes with reduced carbon

  7. How to assess the efficacy of phosphate binders.

    Science.gov (United States)

    Caravaca, Francisco; Caravaca-Fontán, Fernando; Azevedo, Lilia; Luna, Enrique

    The efficacy of phosphate binders is difficult to be estimated clinically. This study analyzes the changes in serum phosphate and urinary phosphate excretion after the prescription of phosphate binders (PB) in patients with chronic kidney disease stage 4-5 pre-dialysis, and the usefulness of the ratio between total urinary phosphate and protein catabolic rate (Pu/PCR) for estimating the efficacy of PB. This retrospective observational cohort study included adult chronic kidney disease patients. Biochemical parameters were determined baseline and after 45-60 days on a low phosphate diet plus PB ("binder" subgroup=260 patients) or only with dietary advice ("control" subgroup=79 patients). Phosphate load (total urinary excretion) per unit of renal function (Pu/GFR) was the best parameter correlated with serum phosphate levels (R(2)=0.61). Mean±SD level of Pu/PCR was 8.2±2.3mg of urinary phosphate per each g of estimated protein intake. After treatment with PB, serum phosphate levels decreased by 11%, urinary phosphate 22%, protein catabolic rate 7%, and Pu/PCR 15%. In the control subgroup, Pu/PCR increased by 20%. Urinary phosphate and urea nitrogen excretion correlated strongly, both baseline and after PB or dietary advice. The proposed parameter Pu/PCR may reflect the rate of intestinal phosphate absorption, and therefore, its variations after PB prescription may be a useful tool for estimating the pharmacological efficacy of these drugs. Copyright © 2016 Sociedad Española de Nefrología. Published by Elsevier España, S.L.U. All rights reserved.

  8. Two-photon polymerization of 3-D zirconium oxide hybrid scaffolds for long-term stem cell growth.

    Science.gov (United States)

    Skoog, Shelby A; Nguyen, Alexander K; Kumar, Girish; Zheng, Jiwen; Goering, Peter L; Koroleva, Anastasia; Chichkov, Boris N; Narayan, Roger J

    2014-06-01

    Two-photon polymerization is a technique that involves simultaneous absorption of two photons from a femtosecond laser for selective polymerization of a photosensitive material. In this study, two-photon polymerization was used for layer-by-layer fabrication of 3-D scaffolds composed of an inorganic-organic zirconium oxide hybrid material. Four types of scaffold microarchitectures were created, which exhibit layers of parallel line features at various orientations as well as pores between the line features. Long-term cell culture studies involving human bone marrow stromal cells were conducted using these 3-D scaffolds. Cellular adhesion and proliferation were demonstrated on all of the scaffold types; tissuelike structure was shown to span the pores. This study indicates that two-photon polymerization may be used to create microstructured scaffolds out of an inorganic-organic zirconium oxide hybrid material for use in 3-D tissue culture systems.

  9. Sustainable asphalt pavement: Application of slaughterhouse waste oil and fly ash in asphalt binder

    Science.gov (United States)

    Sanchez Ramos, Jorge Luis

    Increasing energy costs, lack of sufficient natural resources and the overwhelming demand for petroleum has stimulated the development of alternative binders to modify or replace petroleum-based asphalt binders. In the United States, the petroleum-based asphalt binder is mainly used to produce the Hot Mix Asphalt (HMA). There are approximately 4000 asphalt plants that make 500 million tons of asphalt binder valued at roughly 3 billion/year. The instability of the world's oil market has pushed oil prices to more than 80 per barrel in 2012, which increased the cost of asphalt binder up to $570 per ton. Therefore, there is a timely need to find alternative sustainable resources to the asphalt binder. This paper investigates the possibility of the partial replacement of the asphalt binder with slaughterhouse waste and/or fly ash. In order to achieve this objective, the asphalt binder is mixed with different percentages of waste oil and/or fly ash. In order to investigate the effect of these additives to the performance of the asphalt binder, a complete performance grade test performed on multiple samples. The results of the performance grade tests are compared with a control sample to observe how the addition of the waste oil and/or fly ash affects the sample. Considering the increasing cost and demand of asphalt, the use of slaughterhouse waste oil and/or fly ash as a partial replacement may result in environmental and monetary improvements in the transportation sector.

  10. Next Generation Advanced Binder Chemistries for High Performance, Environmetally DurableThermal Control Material Systems. Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This innovative SBIR Phase I proposal will develop new binder systems through the systematic investigations to tailor required unique performance properties and...

  11. Novel anti-flooding poly(dimethylsiloxane) (PDMS) catalyst binder for microbial fuel cell cathodes

    KAUST Repository

    Zhang, Fang

    2012-11-01

    Poly(dimethylsiloxane) (PDMS) was investigated as an alternative to Nafion as an air cathode catalyst binder in microbial fuel cells (MFCs). Cathodes were constructed around either stainless steel (SS) mesh or copper mesh using PDMS as both catalyst binder and diffusion layer, and compared to cathodes of the same structure having a Nafion binder. With PDMS binder, copper mesh cathodes produced a maximum power of 1710 ± 1 mW m -2, while SS mesh had a slightly lower power of 1680 ± 12 mW m -2, with both values comparable to those obtained with Nafion binder. Cathodes with PDMS binder had stable power production of 1510 ± 22 mW m -2 (copper) and 1480 ± 56 mW m -2 (SS) over 15 days at cycle 15, compared to a 40% decrease in power with the Nafion binder. Cathodes with the PDMS binder had lower total cathode impedance than those with Nafion. This is due to a large decrease in diffusion resistance, because hydrophobic PDMS effectively prevented catalyst sites from filling up with water, improving oxygen mass transfer. The cost of PDMS is only 0.23% of that of Nafion. These results showed that PDMS is a very effective and low-cost alternative to Nafion binder that will be useful for large scale construction of these cathodes for MFC applications. © 2012 Elsevier B.V.

  12. Organic/Inorganic Hybrid Nanostructures for Chemical Plasmonic Sensors

    Science.gov (United States)

    Chang, Sehoon

    2011-12-01

    The work presented in this dissertation suggests novel design of chemical plasmonic sensors which have been developed based on Localized Surface Plasmon Resonance (LSPR), and Surface-enhanced Raman scattering (SERS) phenomena. The goal of the study is to understand the SERS phenomena for 3D hybrid (organic/inorganic) templates and to design of the templates for trace-level detection of selected chemical analytes relevant to liquid explosives and hazardous chemicals. The key design criteria for the development of the SERS templates are utilizing selective polymeric nanocoatings within cylindrical nanopores for promoting selective adsorption of chemical analyte molecules, maximizing specific surface area, and optimizing concentration of hot spots with efficient light interaction inside nanochannels. The organic/inorganic hybrid templates are optimized through a comprehensive understanding of the LSPR properties of the gold nanoparticles, gold nanorods, interaction of light with highly porous alumina template, and the choice of physical and chemical attributes of the selective coating. Furthermore, novel method to assemble silver nanoparticles in 3D as the active SERS-active substrate has been demonstrated by uniform, in situ growth of silver nanoparticles from electroless deposited silver seeds excluding any adhesive polymer layer on template. This approach can be the optimal for SERS sensing applications because it is not necessary to separate the Raman bands of the polyelectrolyte binding layer from those of the desired analyte. The fabrication method is an efficient, simple and fast way to assemble nanoparticles into 3D nanostructures. Addressable Raman markers from silver nanowire crossbars with silver nanoparticles are also introduced and studied. Assembly of silver nanowire crossbar structure is achieved by simple, double-step capillary transfer lithography. The on/off SERS properties can be observed on silver nanowire crossbars with silver nanoparticles

  13. Chitosan chemical hydrogel electrode binder for direct borohydride fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Choudhury, Nurul A.; Sahai, Yogeshwar; Buchheit, Rudolph G. [Department of Materials Science and Engineering, Ohio State University, Columbus, OH (United States)

    2011-01-15

    A novel and cost-effective electrode binder consisting of chitosan chemical hydrogel (CCH) is reported for direct borohydride fuel cells (DBFCs). The DBFCs have been assembled with Misch-metal-based AB{sub 5} alloy as anode, carbon-supported palladium (Pd/C) as cathode and polyvinyl alcohol (PVA) hydrogel membrane electrolyte (PHME) as well as Nafion {sup registered} -117 membrane electrolyte (NME) as separators. Operating in passive mode without using peristaltic pump and under ambient conditions of temperature as well as pressure, the DBFC exhibited a maximum peak power density of about 81 mW cm{sup -2}. (author)

  14. Hexacyanoferrates and bentonite as binders of radiocaesium for reindeer

    Directory of Open Access Journals (Sweden)

    Knut Hove

    1991-10-01

    Full Text Available The effects of varying doses of caesium binders (Bentonite and several forms of iron-hexacyanoferrates on radiocaesium accumulation in red blood cells and on radiocaesium transfer to urine and faeces were studied in feeding experiments with reindeer calves. The caesium binders were added to a ration of lichen (containing 9.5 kBq of 134Cs+137Cs originating from the Chernobyl accident and fed together with a pelleted reindeer feed (RF-71 for 42 days. A 50% reduction in red blood cell radiocaesium concentration was obtained with a daily dose of 1 mg/kg body weigth of ammoniumironhexacyanoferrate (AFCF and with 500 mg/kg of bentonite. Three mg/kg of AFCF or 2 g/kg of bentonite reduced both urinary excretion and RBC concentrations with more than 80%. It is concluded that iron-hexacyanoferrates, as a result of their high caesium binding capacity, are particularly useful as caesium binders for free ranging ruminants like the reindeer.Hexacynoferrater og bentonitt som bindere av radiocesium i reinAbstract in Norwegian / Sammendrag: Effekten av bentonitt og ulike typer jernhexacyanoferrater (Berlinerblått på akkumulering av radioaktivt cesium i røde blodlegemer og på utskilling av radioaktivt cesium i urin ble undersøkt i foringsforsøk med reinkalver. Cesiumbinderne ble gitt daglig sammen med lav som inneholdt 9.5 kBq 134Cs+137Cs fra Tsjernobyl ulykken, og 1 kg reinfor (RF-71 i en periode på 42 dager. En daglig dose på 1 mg/kg kroppsvekt av ammoniumjernhexacyano-ferrat (AFCF reduserte radiocesiuminnholdet i blodlegemer med 50%, mens en dose pa 500 mg/kg bentonitt var nødvendig for å oppnå samme effekt. Tre mg/kg AFCF eller 2 g/kg/bentonitt var nødvendig for å oppnå mer enn 80% reduksjon i radiocesium konsentrasjonen i blodlegemer og i radiocesium utskilling med urinen. På grunn av de små daglige mengder som kreves er jern-hexacyanoferratene spesielt velegnete som cesiumbindere for beitedyr.

  15. Nanomodified compositions based on finely dispersed binders for soil reinforcement

    Directory of Open Access Journals (Sweden)

    Alimov Lev

    2017-01-01

    Full Text Available Theoretical prerequisites on the possibility of improvement of physical and mechanical properties of soils at underground space development, their stability at different aggressive actions by means of their structure impregnation with nanomodified suspensions on the basis of especially finely dispersed mineral binders are developed. The features of influence of plasticizers on penetration ability and sedimentation stability of suspensions are revealed. Soil body reinforcement after its impregnation may achieve considerable values, which is related to the features of interaction of components of impregnating composition with extended surface of soil pore space.

  16. New polymer lithium secondary batteries based on ORMOCER (R) electrolytes-inorganic-organic polymers

    DEFF Research Database (Denmark)

    Popall, M.; Buestrich, R.; Semrau, G.

    2001-01-01

    Based on new plasticized inorganic-organic polymer electrolytes CM. Popall, M. Andrei, J. Kappel, J. Kron, K. Olma, B. Olsowski,'ORMOCERs as Inorganic-organic Electrolytes for New Solid State Lithium Batteries and Supercapacitors', Electrochim. Acta 43 (1998) 1155] new flexible foil-batteries...... electrolyte, typical for polymer electrolytes. Cycling tests (more than 900 cycles) proved that the unplasticized electrolyte can act as binder in composite cathodes of lithium secondary batteries [2]. Charge/discharge cycles of complete batteries like (Cu/active carbon/ORMOCER(R)/LiCoO2/Al) with an ORMOCER......(R) as separator electrolyte were measured. The voltage drop of these batteries is very similar to cells with standard liquid electrolytes and the efficiency is close to 100%. Cycling the batteries with a current density of 0.25 mA cm(-2) between the voltage limits of 3.1 and 4.1 V results in a charge...

  17. The curious case of zeolite-clay/binder interactions and their consequences for catalyst preparation.

    Science.gov (United States)

    Whiting, Gareth T; Chowdhury, Abhishek Dutta; Oord, Ramon; Paalanen, Pasi; Weckhuysen, Bert M

    2016-07-04

    Zeolite-based catalyst bodies are commonly employed in a range of important industrial processes. Depending on the binder and shaping method chosen, vast differences in the reactivity, selectivity and stability are obtained. Here, three highly complementary micro-spectroscopic techniques were employed to study zeolite ZSM-5-binder interactions in SiO2-, Al2O3-, SiO2 : Al2O3- (2 : 1 mix) and kaolinite-bound catalyst pellets. We establish how their preparation influences the zeolite-clay/binder interactions. Using thiophene as an acid-catalyzed staining reaction, light absorbing oligomers produced in each sample were followed. To our surprise, kaolinite decreased the overall reactivity of the sample due to the phase change of the binder, creating a hard impenetrable outer layer. Aluminum migration to the zeolite was observed when Al2O3 was selected as a binder, creating additional Brønsted acid sites, which favored the formation of ring-opened thiophene oligomers compared to the larger oligomer species produced when SiO2 was used as a binder. In the latter case, the interaction of the Si-OH groups in the binder with thiophene was revealed to have a large impact in creating such large oligomer species. Furthermore, the combination of a SiO2 : Al2O3 mix as a binder enhanced the reactivity, possibly due to the creation of additional Brønsted acid sites between the two binder components during pellet preparation. It is evident that, independent of the shaping method, the intimate contact between the zeolite and binder heavily impacts the reactivity and product selectivity, with the type of binder playing a vital role.

  18. Rheological evaluation of polymer-modified asphalt binders

    Directory of Open Access Journals (Sweden)

    Mônica Romero Santos Fernandes

    2008-09-01

    Full Text Available Currently, the most used polymer for asphalt binder modification is the thermoplastic elastomer styrene butadiene styrene (SBS and aromatic oil is commonly added to the mixtures to improve their compatibly. This paper proposes the use of oil shale from sedimentary rock as a compatibilizer agent for polymer-modified asphalt binder (PMB. PMBs were produced by mixing a bitumen with a linear SBS copolymer (3.5% (w.w-1 using two oil shale contents (2 and 4% and petroleum aromatic oil to evaluate comparatively the effect of the compatibilizer agent on the SBS PMB properties. The rheological characteristics of the SBS PMBs were analyzed in a dynamic shear rheometer (DSR and the morphology accessed by fluorescence optical microscopy. The viscoelastic behavior of the samples corroborated the results for the classical properties and varied according to the sample morphology and composition. The results indicate that the aromatic and shale oils have similar effects on the microstructure, storage stability and viscoelastic behavior of the PMBs. Thus, shale oil could be successfully used as a compatibilizer agent without loss of properties or could even replace the aromatic oil. Following the Superpave methodology it was observed that the linear- and radial-SBS PMBs and linear-SBS PMB with 2% of shale oil can be used up to 70 °C, and the linear-SBS PMBs with 4% of shale oil or 2% of aromatic oil can be used only up to 64 °C.

  19. Emissions of tar-containing binders: field studies.

    Science.gov (United States)

    Hugener, Martin; Emmenegger, Lukas; Mattrel, Peter

    2009-01-01

    This study describes the measurement of emissions during field construction of asphalt pavements using tar-containing recycled asphalt pavement (RAP), which is known to release harmful substances, such as polycyclic aromatic hydrocarbons (PAH). At three different test sites, the main emission sources were identified and the total emission rates of fumes and PAHs of the paving process were determined. For this purpose, the paver was temporarily enclosed. While the screed area was the main emission source, the hopper area and freshly compacted pavement were also significant. In comparison with previous laboratory tests, the binder composition and the resulting emissions were comparable, except for Naphthalene. Benzo(a)pyrene (BaP) as a representative for carcinogenic PAHs was identified as a good leading compound, correlating well with the toxicity weighted sum of PAHs. In contrast, the unweighted, mass related sum of all EPA PAHs does not seem to be a good parameter to assess workplace concentrations because emissions by mass are dominated by the less hazardous 2-, 3- and 4-ring PAHs. Workplace concentrations for bitumen fumes and PAHs were below limit values in all three field studies. However, the margin was not large and the field tests were done under favourable meteorological conditions. Therefore, we suggest maintaining the current Swiss limit of 5000 mg EPA-PAH per kg binder in the RAP-containing hot mix.

  20. Predictive cartography of metal binders using generative topographic mapping

    Science.gov (United States)

    Baskin, Igor I.; Solov'ev, Vitaly P.; Bagatur'yants, Alexander A.; Varnek, Alexandre

    2017-08-01

    Generative topographic mapping (GTM) approach is used to visualize the chemical space of organic molecules (L) with respect to binding a wide range of 41 different metal cations (M) and also to build predictive models for stability constants (log K) of 1:1 (M:L) complexes using "density maps," "activity landscapes," and "selectivity landscapes" techniques. A two-dimensional map describing the entire set of 2962 metal binders reveals the selectivity and promiscuity zones with respect to individual metals or groups of metals with similar chemical properties (lanthanides, transition metals, etc). The GTM-based global (for entire set) and local (for selected subsets) models demonstrate a good predictive performance in the cross-validation procedure. It is also shown that the data likelihood could be used as a definition of the applicability domain of GTM-based models. Thus, the GTM approach represents an efficient tool for the predictive cartography of metal binders, which can both visualize their chemical space and predict the affinity profile of metals for new ligands.

  1. Highly flexible binder-free core-shell nanofibrous electrode for lightweight electrochemical energy storage using recycled water bottles

    Science.gov (United States)

    Shi, HaoTian H.; Naguib, Hani E.

    2016-08-01

    The creation of a novel flexible nanocomposite fiber with conductive polymer polyaniline (PAni) coating on a polyethylene terephthalate (PET) substrate allowed for increased electrochemical performance while retaining ideal mechanical properties such as very high flexibility. Binder-free PAni-wrapped PET (PAni@PET) fiber with a core-shell structure was successfully fabricated through a novel technique. The PET nanofiber substrate was fabricated through an optimized electrospinning method, while the PAni shell was chemically polymerized onto the surface of the nanofibers. The PET substrate can be made directly from recycled PETE1 grade plastic water bottles. The resulting nanofiber with an average diameter of 121 nm ± 39 nm, with a specific surface area of 83.72 m2 g-1, led to better ionic interactions at the electrode/electrolyte interface. The PAni active layer coating was found to be 69 nm in average thickness. The specific capacitance was found to have increased dramatically from pure PAni with carbon binders. The specific capacitance was found to be 347 F g-1 at a relatively high scan rate of 10 mV s-1. The PAni/PET fiber also experienced very little degradation (4.4%) in capacitance after 1500 galvanostatic charge/discharge cycles at a specific current of 1.2 A g-1. The mesoporous structure of the PAni@PET fibrous mat also allowed for tunable capacitance by controlling the pore sizes. This novel fabrication method offers insights for the utilization of recycled PETE1 based bottles as a high performance, low cost, highly flexible supercapacitor device.

  2. Selective inorganic thin films

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, M.L.F.; Pohl, P.I.; Brinker, C.J. [Sandia National Labs., Albuquerque, NM (United States)

    1997-04-01

    Separating light gases using membranes is a technology area for which there exists opportunities for significant energy savings. Examples of industrial needs for gas separation include hydrogen recovery, natural gas purification, and dehydration. A membrane capable of separating H{sub 2} from other gases at high temperatures could recover hydrogen from refinery waste streams, and facilitate catalytic dehydrogenation and the water gas shift (CO + H{sub 2}O {yields} H{sub 2} + CO{sub 2}) reaction. Natural gas purification requires separating CH{sub 4} from mixtures with CO{sub 2}, H{sub 2}S, H{sub 2}O, and higher alkanes. A dehydrating membrane would remove water vapor from gas streams in which water is a byproduct or a contaminant, such as refrigeration systems. Molecular sieve films offer the possibility of performing separations involving hydrogen, natural gas constituents, and water vapor at elevated temperatures with very high separation factors. It is in applications such as these that the authors expect inorganic molecular sieve membranes to compete most effectively with current gas separation technologies. Cryogenic separations are very energy intensive. Polymer membranes do not have the thermal stability appropriate for high temperature hydrogen recovery, and tend to swell in the presence of hydrocarbon natural gas constituents. The authors goal is to develop a family of microporous oxide films that offer permeability and selectivity exceeding those of polymer membranes, allowing gas membranes to compete with cryogenic and adsorption technologies for large-scale gas separation applications.

  3. Polymerizable Ionic Liquid Crystals Comprising Polyoxometalate Clusters toward Inorganic-Organic Hybrid Solid Electrolytes

    Directory of Open Access Journals (Sweden)

    Takeru Ito

    2017-07-01

    Full Text Available Solid electrolytes are crucial materials for lithium-ion or fuel-cell battery technology due to their structural stability and easiness for handling. Emergence of high conductivity in solid electrolytes requires precise control of the composition and structure. A promising strategy toward highly-conductive solid electrolytes is employing a thermally-stable inorganic component and a structurally-flexible organic moiety to construct inorganic-organic hybrid materials. Ionic liquids as the organic component will be advantageous for the emergence of high conductivity, and polyoxometalate, such as heteropolyacids, are well-known as inorganic proton conductors. Here, newly-designed ionic liquid imidazolium cations, having a polymerizable methacryl group (denoted as MAImC1, were successfully hybridized with heteropolyanions of [PW12O40]3− (PW12 to form inorganic-organic hybrid monomers of MAImC1-PW12. The synthetic procedure of MAImC1-PW12 was a simple ion-exchange reaction, being generally applicable to several polyoxometalates, in principle. MAImC1-PW12 was obtained as single crystals, and its molecular and crystal structures were clearly revealed. Additionally, the hybrid monomer of MAImC1-PW12 was polymerized by a radical polymerization using AIBN as an initiator. Some of the resulting inorganic-organic hybrid polymers exhibited conductivity of 10−4 S·cm−1 order under humidified conditions at 313 K.

  4. Design and synthesis of organic-inorganic hybrid capsules for biotechnological applications.

    Science.gov (United States)

    Shi, Jiafu; Jiang, Yanjun; Wang, Xiaoli; Wu, Hong; Yang, Dong; Pan, Fusheng; Su, Yanlei; Jiang, Zhongyi

    2014-08-07

    Organic-inorganic hybrid capsules, which typically possess a hollow lumen and a hybrid wall, have emerged as a novel and promising class of hybrid materials and have attracted enormous attention. In comparison to polymeric capsules or inorganic capsules, the hybrid capsules combine the intrinsic physical/chemical properties of the organic and inorganic moieties, acquire more degrees of freedom to manipulate multiple interactions, create hierarchical structures and integrate multiple functionalities. Thus, the hybrid capsules exhibit superior mechanical strength (vs. polymeric capsules) and diverse functionalities (vs. inorganic capsules), which may give new opportunities to produce high-performance materials. Much effort has been devoted to exploring innovative and effective methods for the synthesis of hybrid capsules that exhibit desirable performance in target applications. This tutorial review firstly presents a brief description of the capsular structure and hybrid materials in nature, then classifies the hybrid capsules into molecule-hybrid capsules and nano-hybrid capsules based upon the size of the organic and inorganic moieties in the capsule wall, followed by a detailed discussion of the design and synthesis of the hybrid capsules. For each kind of hybrid capsule, the state-of-the-art synthesis methods are described in detail and a critical comment is embedded. The applications of these hybrid capsules in biotechnological areas (biocatalysis, drug delivery, etc.) have also been summarized. Hopefully, this review will offer a perspective and guidelines for the future research and development of hybrid capsules.

  5. Living olefin polymerization processes

    Science.gov (United States)

    Schrock, Richard R.; Baumann, Robert

    1999-01-01

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  6. Phosphazene-promoted anionic polymerization

    KAUST Repository

    Zhao, Junpeng

    2014-01-01

    In the recent surge of metal-free polymerization techniques, phosphazene bases have shown their remarkable potential as organic promoters/catalysts for the anionic polymerization of various types of monomers. By complexation with the counterion (e.g. proton or lithium cation), phosphazene base significantly improve the nucleophilicity of the initiator/chain-end resulting in rapid and usually controlled anionic/quasi-anionic polymerization. In this review, we will introduce the general mechanism, i.e. in situ activation (of initiating sites) and polymerization, and summarize the applications of such a mechanism on macromolecular engineering toward functionalized polymers, block copolymers and complex macromolecular architectures.

  7. Nanocomposites of polymer and inorganic nanoparticles for optical and magnetic applications

    Directory of Open Access Journals (Sweden)

    Shanghua Li

    2010-08-01

    Full Text Available This article provides an up-to-date review on nanocomposites composed of inorganic nanoparticles and the polymer matrix for optical and magnetic applications. Optical or magnetic characteristics can change upon the decrease of particle sizes to very small dimensions, which are, in general, of major interest in the area of nanocomposite materials. The use of inorganic nanoparticles into the polymer matrix can provide high-performance novel materials that find applications in many industrial fields. With this respect, frequently considered features are optical properties such as light absorption (UV and color, and the extent of light scattering or, in the case of metal particles, photoluminescence, dichroism, and so on, and magnetic properties such as superparamagnetism, electromagnetic wave absorption, and electromagnetic interference shielding. A general introduction, definition, and historical development of polymer–inorganic nanocomposites as well as a comprehensive review of synthetic techniques for polymer–inorganic nanocomposites will be given. Future possibilities for the development of nanocomposites for optical and magnetic applications are also introduced. It is expected that the use of new functional inorganic nano-fillers will lead to new polymer–inorganic nanocomposites with unique combinations of material properties. By careful selection of synthetic techniques and understanding/exploiting the unique physics of the polymeric nanocomposites in such materials, novel functional polymer–inorganic nanocomposites can be designed and fabricated for new interesting applications such as optoelectronic and magneto-optic applications.

  8. Effects of binders on the electrochemical performance of rechargeable magnesium batteries

    Science.gov (United States)

    Wang, Nan; NuLi, Yanna; Su, Shuojian; Yang, Jun; Wang, Jiulin

    2017-02-01

    A comparative study on the effects of different binders on the electrochemical performance of rechargeable magnesium batteries with Mo6S8 cathode is conducted for the first time. The selected binders are commercial organic-soluble polyvinylidene fluoride (PVDF), water-soluble poly(acrylic acid) (PAA), poly(vinyl alcohol) (PVA), gelatin, sodium alginate (SA) and Beta-cyclodextrin (β-CD). The binders significantly affect the physical properties, thus the electrochemical performance of Mo6S8 cathode. Compared with those using traditional PVDF binder, Mo6S8 electrodes with PAA and PVA exhibit enhanced cycling stabilities and rate capabilities, which are attributed to the improved cohesion among the electrode constituents and adhesion between the electrode laminate and the current collector. In addition, the anodic stability of these binders is not only related to the chemical structure of binders, but also to the uniformity of electrode surface. SA binder shows low anodic stability duo to containing easily oxidized groups. Non-uniform electrode surface decreases the anodic stability of PVDF based Mo6S8 electrode. Gelatin can be used as a binder in the formulation of high voltage cathodes for rechargeable magnesium batteries.

  9. Setup of Columellar Height with Costal Cartilage Graft Modification in a Patient with Binder Syndrome

    Directory of Open Access Journals (Sweden)

    Şafak Uygur

    2016-03-01

    Full Text Available Binder syndrome is an uncommon disorder of unknown etiology. It is characterized by hypoplasia of the nose and maxilla and altered morphology of the associated soft tissue. We present a surgical technique for setting up the columellar height in a patient with Binder syndrome.

  10. 14 CFR 198.15 - Non-premium insurance-payment of registration binders.

    Science.gov (United States)

    2010-01-01

    ... OF TRANSPORTATION (CONTINUED) WAR RISK INSURANCE AVIATION INSURANCE § 198.15 Non-premium insurance... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Non-premium insurance-payment of...-premium insurance must be accompanied by the proper binder, payable to the FAA. A binder is not...

  11. Evaluation of bitumen-rubber asphalt manufactured from modified binder at lower viscosity

    CSIR Research Space (South Africa)

    O'Connell, Johannes S

    2010-08-01

    Full Text Available In South Africa, crumb tyre-modified bitumen commnly known as bitumen-rubber binder has viscosity limits specified by the current edition of TG1: The Use of Modified Bituminous Binders in Road Construction. As the crumb rubber is 'digested...

  12. Pigment encapsulation by emulsion polymerization using macro-RAFT copolymers.

    Science.gov (United States)

    Nguyen, Duc; Zondanos, Hollie S; Farrugia, Jason M; Serelis, Algirdas K; Such, Chris H; Hawkett, Brian S

    2008-03-04

    A new method is described, based on living amphipathic random macro-RAFT copolymers, which enables the efficient polymeric encapsulation of both inorganic and organic particulate materials via free-radical polymerization. The mechanism for this new approach is examined in the context of the polymer coating of zirconia- and alumina-coated titanium dioxide particles and its breadth of application demonstrated by the coating of organic phthalocyanine blue pigment particles. The particulate materials were first dispersed in water using a macro-RAFT copolymer as a stabilizer. Monomer and water-soluble initiator were then added to the system, and the monomer polymerized to form the coating. If nucleation of new polymer particles in the aqueous phase was to be avoided, it was found necessary to use a macro-RAFT copolymer that did not form micelles; within this constraint, a broad range of RAFT agents could be used. The macro-RAFT agents used in this work were found not to transfer competitively in the aqueous phase and therefore did not support growth of aqueous-phase polymer. Successful encapsulation of particles was demonstrated by TEM. The process described enables 100% of the particles to be encapsulated with greater than 95% of the polymer finishing up in the polymeric shells around the particles. Moreover, the coating reaction can be carried out at greater than 50% solids in many cases and avoids the agglomeration of particles during the coating step.

  13. Preparation of polymeric aluminium ferric chloride from bauxite tailings

    Directory of Open Access Journals (Sweden)

    Ma D.

    2013-01-01

    Full Text Available Bauxite tailings are the main solid wastes in the ore dressing process. The Al2O3 and Fe2O3 contents in bauxite tailings can reach 50% and 13% respectively. The present study proposed a feasible method to use bauxite tailings to prepare polymeric aluminium ferric chloride (PAFC, a new composite inorganic polymer for water purification. Bauxite tailings roasted reacting with hydrochloric acid under air, pickle liquor which mainly contains Fe3+, Al3+ was generated, then calcium aluminate was used to adjust pH value and the basicity of the pickle liquor, the PAFC was subsequently prepared after the polymerization process. The optimal synthesizing parameters for the preparation of PAFC obtained were as follows: the concentration of hydrochloric acid of 24 wt%, ratio of hydrochloric acid to bauxite tailings of 6:1, temperature of 90ºC, leaching time of 2.5 hours, ration of pickle liquor to calcium aluminate of 12:1, polymerization temperature of 90ºC and polymerization time of about 3 hours. The basicity of PAFC was higher than 68%, the sum concentration of Al2O3 and Fe2O3 was beyond 12.5%. The results of flocculation tests indicate that the PAFC has a better performance of removing the turbidity of wastewater compared to PAC, and PAFC prepared by bauxite tailings is a kind of high quality flocculants.

  14. Decreased Bacterial Attachment and Protein Adsorption to Coatings Produced by Low Enegy Plasma Polymerization

    DEFF Research Database (Denmark)

    Andersen, T.E.; Kingshott, Peter; Benter, M.

    with a surface less prone to the adsorption of biological matter. In the current study two different hydrophilic nanoscale coatings were produced by low energy plasma polymerization [3] and investigated· f()rl()w ... pr()tein adsorption and bacterial attachment properties. Methods were setup to enable...... and Methods: Coatings: Plasma polymerized poly(vinyl pyrrolidone) (PP-PVP), poly(2-methoxyethyl methacrylate) (PPPMEA) or an inorganic oxide (10) coating were applied onto medical grade silicon rubber sheets (Silopren LSR 2050, Momentive Performance Materials Inc.). Plasma polymerization chamber......-coated crystals were then treated with one of the plasma polymerized coatings. Adsorption of fibrinogen, human serum albumin or immunoglobulin G was measured using a QCM-D instrument [5] (model E4, Q-Sense AB, Vastra Frolunda, Sweden) using a solution of 50llg/1 protein in PBS buffer. Results and Discussion: Our...

  15. Silica-Polystyrene Nanocomposite Particles Synthesized by Nitroxide-Mediated Polymerization and Their Encapsulation through Miniemulsion Polymerization

    Directory of Open Access Journals (Sweden)

    Bérangère Bailly

    2006-01-01

    Full Text Available Polystyrene (PS chains with molecular weights comprised between 8000 and 64000 g⋅mol-1 and narrow polydispersities were grown from the surface of silica nanoparticles (Aerosil A200 fumed silica and Stöber silica, resp. through nitroxide-mediated polymerization (NMP. Alkoxyamine initiators based on N-tert-butyl-1-diethylphosphono-2,2-dimethylpropyl nitroxide (DEPN and carrying a terminal functional group have been synthesized in situ and grafted to the silica surface. The resulting grafted alkoxyamines have been employed to initiate the growth of polystyrene chains from the inorganic surface. The maximum grafting density of the surface-tethered PS chains was estimated and seemed to be limited by initiator confinement at the interface. Then, the PS-grafted Stöber silica nanoparticles were entrapped inside latex particles via miniemulsion polymerization. Transmission electron microscopy indicated the successful formation of silica-polystyrene core-shell particles.

  16. Investigation of binder distribution in graphite anodes for lithium-ion batteries

    Science.gov (United States)

    Müller, Marcus; Pfaffmann, Lukas; Jaiser, Stefan; Baunach, Michael; Trouillet, Vanessa; Scheiba, Frieder; Scharfer, Philip; Schabel, Wilhelm; Bauer, Werner

    2017-02-01

    Energy dispersive x-ray spectroscopy (EDS) is evaluated regarding its applicability for revealing the binder distribution in lithium-ion battery electrode films. Graphite anodes comprising carbon black and PVDF binder are subject to varying drying conditions during solvent removal in order to adjust different binder distributions; fluorine is used as a marker for the presence of PVDF. For electrodes of about 70 μm thickness the fluorine concentration is detected at the surface of the electrode film as well as at the interface between electrode film and current collector foil. It is clearly visible by EDS that increasing drying temperatures (and drying rates) result in an accumulation of binder at the surface and a corresponding depletion at the interface. It is demonstrated on the basis of ion-milled cross-sections of thick electrodes (ca. 400 μm) that a quantitative mapping of the binder distribution delivers additional information about concentration gradients in dependence of the drying parameters.

  17. Study of chloride ion transport of composite by using cement and starch as a binder

    Energy Technology Data Exchange (ETDEWEB)

    Armynah, Bidayatul; Halide, Halmar; Zahrawani,; Reski, Nurhadi; Tahir, Dahlang, E-mail: dtahir@fmipa.unhas.ac.id [Department of Physics, Hasanuddin University, Makassar 90245 Indonesia (Indonesia)

    2016-03-11

    This study presents the chemical bonding and the structural properties of composites from accelerator chloride test migration (ACTM). The volume fractions between binder (cement and starch) and charcoal in composites are 20:80 and 60:40. The effect of the binder to the chemical composition, chemical bonding, and structural properties before and after chloride ion passing through the composites was determined by X-ray fluorescence (XRF), by Fourier transform infra-red (FTIR), and x-ray diffraction (XRD), respectively. From the XRD data, XRF data, and the FTIR data shows the amount of chemical composition, the type of binding, and the structure of composites are depending on the type of binder. The amount of chloride migration using starch as binder is higher than that of cement as a binder due to the density effects.

  18. Gratings in polymeric waveguides

    Science.gov (United States)

    Mishakov, G.; Sokolov, V.; Kocabas, A.; Aydinli, A.

    2007-04-01

    Laser-induced formation of polymer Bragg grating filters for Dense Wavelength Division Multiplexing (DWDM) applications is discussed. Acrylate monomers halogenated with both fluorine and chlorine, which possess absorption losses less than 0.25 dB/cm and wide choice of refractive indices (from 1.3 to 1.5) in the 1.5 μm telecom wavelength region were used. The monomers are highly intermixable thus permitting to adjust the refractive index of the composition within +/-0.0001. Moreover they are photocurable under UV exposure and exhibit high contrast in polymerization. These properties make halogenated acrylates very promising for fabricating polymeric waveguides and photonic circuits. Single-mode polymer waveguides were fabricated on silicon wafers using resistless contact lithography. Submicron index gratings have been written in polymer waveguides using holographic exposure with He-Cd laser beam (325 nm) through a phase mask. Both uniform and apodized gratings have been fabricated. The gratings are stable and are not erased by uniform UV exposure. The waveguide gratings possess narrowband reflection spectra in the 1.5 μm wavelength region of 0.4 nm width, nearly rectangular shape of the stopband and reflectivity R > 99%. The fabricated Bragg grating filters can be used for multiplexing/demultiplexing optical signals in high-speed DWDM optical fiber networks.

  19. Essentials of inorganic materials synthesis

    CERN Document Server

    Rao, C N R

    2015-01-01

    This compact handbook describes all the important methods of synthesis employed today for synthesizing inorganic materials. Some features: Focuses on modern inorganic materials with applications in nanotechnology, energy materials, and sustainability Synthesis is a crucial component of materials science and technology; this book provides a simple introduction as well as an updated description of methods Written in a very simple style, providing references to the literature to get details of the methods of preparation when required

  20. Inorganic materials in industrial processes

    OpenAIRE

    Demadis, Konstantinos

    2015-01-01

    Although inorganic materials represent a small number to the extreme number of the organic ones, they play a number of crucial roles in several processes of industrial interest. Two significant technologically processes have been selected as “case studies” for this presentation: metallic corrosion and its control, and mitigation of inorganic deposits, both related to industrial water systems. Universidad de Málaga. Campus de Excelencia Internacional Andalucía Tech.

  1. Highly Branched Bio-Based Unsaturated Polyesters by Enzymatic Polymerization

    Directory of Open Access Journals (Sweden)

    Hiep Dinh Nguyen

    2016-10-01

    Full Text Available A one-pot, enzyme-catalyzed bulk polymerization method for direct production of highly branched polyesters has been developed as an alternative to currently used industrial procedures. Bio-based feed components in the form of glycerol, pentaerythritol, azelaic acid, and tall oil fatty acid (TOFA were polymerized using an immobilized Candida antarctica lipase B (CALB and the potential for an enzymatic synthesis of alkyds was investigated. The developed method enables the use of both glycerol and also pentaerythritol (for the first time as the alcohol source and was found to be very robust. This allows simple variations in the molar mass and structure of the polyester without premature gelation, thus enabling easy tailoring of the branched polyester structure. The postpolymerization crosslinking of the polyesters illustrates their potential as binders in alkyds. The formed films had good UV stability, very high water contact angles of up to 141° and a glass transition temperature that could be controlled through the feed composition.

  2. Electrochemical behavior of organic and inorganic zinc-rich coatings in 3.5% NaCl solution

    Institute of Scientific and Technical Information of China (English)

    谢德明; 王建明; 胡吉明; 张鉴清

    2003-01-01

    Performance comparisons between organic and inorganic zinc-rich paints (ZRPs) were carried out. Electrochemical impedance spectroscopy (EIS) measurements were used to assess the corrosion prevention performance of the ZRP coatings. The results show that during the cathodic protection period the potentials of the epoxy systems are less negative than those of the silicate system. For the zinc-rich ethyl silicate paints, the initial values of the resistance through the binder and the charge transfer resistance associated with zinc dissolution are several orders of magnitude lower than those of the organic zinc paints, while the initial values of the capacitance due to the binder layer between Zn dust and the double layer capacitance for zinc dissolution are several orders of magnitude higher than those of the organic zinc paints. Furthermore, the deterioration with time of capability of the zinc particles in the paint to provide cathodic protection to the steel was interpreted.

  3. INFLUENCE OF POLYMERIC ADDITIVES ON CRYSTALLIZATION OF CALCIUM SULPHATE DIHYDRATE

    Directory of Open Access Journals (Sweden)

    Ustinova Yulia Valer’evna

    2013-04-01

    Full Text Available Currently, functional additives are widely spread in the production of inorganic dry mixtures. However, their impact on the microstructure of products, generated in the process of hardening of inorganic binders, is understudied. In this context, the goal of the work is the study of calcium sulfate dihydrate (CaSO •2H O crystallization. Super plasticizer based on sulfonated melamine-formaldehyde resin, methylcellulose and vinyl acetate, ethylene and vinyl chloride copolymer powder were selected for studies. First, pure calcium sulfate dihydrate crystals were synthesized. Then, synthesized calcium sulfate dihydrate crystals were exposed to the X-ray analysis to determine the nature of influence of polymer additives on the shape and dimensions of crystals. Possible combinations of simple forms of CaSO •2H O were identified by the X-ray analysis and the special software. Electronic microscopy analysis was performed to validate models of calcium sulfate dihydrate crystals. All plasticizers influence the crystallization of calcium sulfate dihydrate. The influence of additives on the shape and dimensions of crystals of calcium sulfate dihydrate can be explained by the fact that molecules of sulfonated melamine-formaldehyde resins, methylcellulose, and copolymers of vinyl acetate, ethylene and vinyl chloride are absorbed by crystal faces. It is proven that the method of X-ray analysis can be used to predict the shape and habitus of crystals.

  4. Development of partitioning method: adsorption behavior of Sr on titanic acid pelletized with binder

    Energy Technology Data Exchange (ETDEWEB)

    Mizoguchi, Kenichi; Yamaguchi, Isoo; Morita, Yasuji; Yamagishi, Isao; Fujiwara, Takeshi; Kubota, Masumitsu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-05-01

    The adsorption behavior of Sr was examined with the titanic acid with the binder and with binderless titanic acid. Then the effect of the difference of the neutralizer was also examined. When the initial concentration of Sr was constant, distribution coefficient (Kd) increased with pH after adsorption. At pH 4, Kd decreased in order of the titanic acid neutralized with NH{sub 4}OH solution without the binder > the titanic acid neutralized with NH{sub 4}OH solution and pelletized with the binder > the titanic acid neutralized with KOH solution and pelletized with the binder. At pH 6, Kd decreased with increasing the concentration of Sr in the solution, but the decreasing tendency of Kd for each titanic acid was the same. Adsorption kinetics was examined with titanic acids neutralized with NH{sub 4}OH solution, keeping the initial concentration of Sr and the initial pH constant. It took about one hour to reach Kd of 100mL/g for the titanic acid without the binder but over 10 hours for the titanic acid pelletized with the binder. It was confirmed that by pelletizing titanic acid with the binder, Kd of Sr became small and it took very long time to reach the adsorption equilibrium. However, by sufficient conditioning with water of the titanic acid pelletized with the binder, 1) it took about half time of titanic acid without conditioning to reach Kd of 100mL/g, 2) after 24 hours mixing, Kd for the titanic acid pelletized with the binder was almost equal to that for the titanic acid without the binder, 3) apparent ion exchange capacity obtained through a column test became over about 1meq/g. (J.P.N.)

  5. Effects of Surface-modification of Carbon Black on the Characteristics of Polymerized Toner

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Eun Ho; Kim, Dae Su [Chungbuk National University, Cheongju (Korea, Republic of)

    2013-10-15

    Carbon black was surface-modified to prepare styrene-based suspension polymerized toner with excellent carbon black dispersibility inside toner particles. Carbon black was oxidized first to introduce hydroxyl groups on the surfaces, then esterification between the hydroxyl groups and carboxyl groups of organic acids (oleic acid, palmitic acid, acrylic acid) was followed to obtain organically surface-modified carbon black. The surface-modification of carbon black was confirmed by FTIR. Apparent carbon black dispersibility in the monomer mixture of the binder resin was tested and the particle size of dispersed carbon black was measured by particle size analyzer. Optical micrographs showed that carbon black dispersibility inside toner particles was improved considerably when the carbon black surface-modified with oleic acid was used. The polymerized toner prepared with the carbon black surface-modified with oleic acid showed ideal particle size and size distribution as a toner.

  6. Fracture properties of concrete specimens made from alkali activated binders

    Science.gov (United States)

    Šimonová, Hana; Kucharczyková, Barbara; Topolář, Libor; Bílek, Vlastimil, Jr.; Keršner, Zbyněk

    2017-09-01

    The aim of this paper is to quantify crack initiation and other fracture properties – effective fracture toughness and specific fracture energy – of two types of concrete with an alkali activated binder. The beam specimens with a stress concentrator were tested in a three-point bending test after 28, 90, and 365 days of maturing. Records of fracture tests in the form of load versus deflection (P–d) diagrams were evaluated using effective crack model and work-of-fracture method and load versus mouth crack opening displacement (P–CMOD) diagrams were evaluated using the Double-K fracture model. The initiation of cracks during the fracture tests for all ages was also monitored by the acoustic emission method. The higher value of monitored mechanical fracture parameters of concrete with alkali activated blast furnace slag were achieved with substitution blast furnace slag by low calcium fly ash in comparison with substitution by cement kiln dust.

  7. Zeolite and bentonite as caesium binders in reindeer feed

    Directory of Open Access Journals (Sweden)

    Birgitta Åhman

    1990-09-01

    Full Text Available The effects of zeolite and bentonite on the accumulation and excretion of radiocaesium (Cs-137 in reindeer were studied in two feeding experiments. Six animals in each experiment were given lichens contaminated with radiocaesium from fallout after the Chernobyl nuclear power plant accident. In addition, they were fed pellets containing bentonite (Experiment I or zeolite (Experiment II. Two animals, controls, in each experiment received no caesium-binder. The activity concentration of radiocaesium in blood was used to evalute the radiocaesium level in the body. Faeces and urine were collected to measue the excration of radiocaesium. The animals in Experiment I were depleted of radiocaesium before the start of the experiment. After three weeks, with an intake of 17 - 18 kBq Cs-137/day, the controls had reached activity concentrations of radiocaesium in blood corresponding to 4 - 4.5 kBq Cs-137/kg in muscle. Reindeer fed 23 or 46 g of bentonite per day stabilized at values below 0.8 kfiq/kg in muscle. In Experiment II, the reindeer started with radiocaesium activity concentrations in blood corresponding to 2 - 4.5 kBq Cs-137/kg in muscle. After four weeks of feeding, with an intake at about 8.5 kBq Cs-137/day, controls had increased their radiocaesium values by an average of 40%. Reindeer receiving 25 or 50 g zeolite per day decreased with 18 and 45%, respectively. Net absorption of radiocaesium from the gastro-intestinal tract was calculated at 50 -70% in animals receiving no caesium-binder. Reindeer fed bentonite had an absorption below 10% while those fed zeolite absorbed around 35%.

  8. Pharmaceutical equivalence of metformin tablets with various binders

    Directory of Open Access Journals (Sweden)

    L. C. Block

    2009-01-01

    Full Text Available

    Metformin hydrochloride is a high-dose drug widely used as an oral anti-hyperglycemic agent. As it is highly crystalline and has poor compaction properties, it is difficult to form tablets by direct compression. The aim of this study was to develop adequate metformin tablets, pharmaceutically equivalent to the reference product, Glucophage® (marketed as Glifage® in Brazil. Metformin 500mg tablets were produced by wet granulation with various binders (A = starch, B = starch 1500®, C = PVP K30®, D = PVP K90®. The tablets were analyzed for their hardness, friability, disintegration, dissolution, content uniformity and dissolution profile (basket apparatus at 50 rpm, pH 6.8 phosphate buffer. The 4 formulations, F1 (5% A and 5% C, F2 (5% B and 5% C, F3 (10% C and F4 (5% D, demonstrated adequate uniformity of content, hardness, friability, disintegration and total drug dissolution after 30 minutes (F1, F2 and F4, and after 60 minutes (F3. The drug release time profiles fitted a Higuchi model (F1, F2 and F3, similarly to the pharmaceutical reference, or a zero order model (F4. The dissolution efficiency for all the formulations was 75%, except for F3 (45%. F1 and F2 were thus equivalent to Glifage®. Keywords: dissolution; metformin; tablet; binder; pharmaceutical equivalence

  9. RELATIVE DOSING OF PHOSPHATE BINDERS FOR EFFECTIVE MANAGEMENT OF PHOSPHATE AND PROTEIN INTAKE IN CHRONIC KIDNEY DISEASE

    Directory of Open Access Journals (Sweden)

    J Brian Copley

    2012-06-01

    The availability of binding capacity data for P binders, presents physicians with the possibility of tailoring doses of binder to a patient’s diet, facilitating sufficient intake of dietary protein while maintaining a neutral P balance. Use of high-capacity binders, such as lanthanum carbonate, would minimize the tablet burden faced by patients and this may also encourage adherence.

  10. 2013 Gordon Research Conference, Inorganic reaction mechanisms, Galveston, TX, March 3-8 2013

    Energy Technology Data Exchange (ETDEWEB)

    Abu-Omar, Mahdi M. [Purdue Univ., West Lafayette, IN (United States)

    2012-12-08

    The 2013 Gordon Conference on Inorganic Reaction Mechanisms will present cutting-edge research on the molecular aspects of inorganic reactions involving elements from throughout the periodic table and state-of-the art techniques that are used in the elucidation of reaction mechanisms. The Conference will feature a wide range of topics, such as homogeneous and heterogeneous catalysis, metallobiochemistry, electron-transfer in energy reactions, polymerization, nitrogen fixation, green chemistry, oxidation, solar conversion, alkane functionalization, organotransition metal chemistry, and computational chemistry. The talks will cover themes of current interest including energy, materials, and bioinorganic chemistry. Sections cover: Electron-Transfer in Energy Reactions; Catalytic Polymerization and Oxidation Chemistry; Kinetics and Spectroscopy of Heterogeneous Catalysts; Metal-Organic Chemistry and its Application in Synthesis; Green Energy Conversion;Organometallic Chemistry and Activation of Small Molecules; Advances in Kinetics Modeling and Green Chemistry; Metals in Biology and Disease; Frontiers in Catalytic Bond Activation and Cleavage.

  11. Collaborative Research: Polymeric Multiferroics

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Shenqiang [Temple Univ., Philadelphia, PA (United States). College of Engineering

    2017-04-20

    The goal of this project is to investigate room temperature magnetism and magnetoelectric coupling of polymeric multiferroics. A new family of molecular charge-transfer crystals has been emerged as a fascinating opportunity for the development of all-organic electrics and spintronics due to its weak hyperfine interaction and low spin-orbit coupling; nevertheless, direct observations of room temperature magnetic spin ordering have yet to be accomplished in organic charge-transfer solids. Furthermore, room temperature magnetoelectric coupling effect hitherto known multiferroics, is anticipated in organic donor-acceptor complexes because of magnetic field effects on charge-transfer dipoles, yet this is also unexplored. The PI seeks to fundamental understanding of the control of organic crystals to demonstrate and explore room temperature multiferroicity. The experimental results have been verified through the theoretical modeling.

  12. Trace the polymerization induced by gamma-ray irradiated silica particles

    Science.gov (United States)

    Lee, Hoik; Ryu, Jungju; Kim, Myungwoong; Im, Seung Soon; Kim, Ick Soo; Sohn, Daewon

    2016-08-01

    A γ-ray irradiation to inorganic particles is a promising technique for preparation of organic/inorganic composites as it offers a number of advantages such as an additive-free polymerizations conducted under mild conditions, avoiding undesired damage to organic components in the composites. Herein, we demonstrated a step-wise formation mechanism of organic/inorganic nanocomposite hydrogel in detail. The γ-ray irradiation to silica particles dispersed in water generates peroxide groups on their surface, enabling surface-initiated polymerization of acrylic acid from the inorganic material. As a result, poly(acrylic acid) (PAA) covers the silica particles in the form of a core-shell at the initial stage. Then, PAA-coated silica particles associate with each other by combination of radicals at the end of chains on different particles, leading to micro-gel domains. Finally, the micro-gels are further associated with each other to form a 3D network structure. We investigated this mechanism using dynamic light scattering (DLS) and transmission electron microscopy (TEM). Our result strongly suggests that controlling reaction time is critical to achieve specific and desirable organic/inorganic nanocomposite structure among core-shell particles, micro-gels and 3D network bulk hydrogel.

  13. Mitigating Impacts Of Arsenic Contaminated Materials Via Two (2) Stabilization Methods Based On Polymeric And Cement Binders

    Science.gov (United States)

    The primary objective of this study was to evaluate the performance of two selected chemical stabilization and solidification (S/S) techniques to treat three types of arsenic-contaminated wastes 1) chromated copper arsenate (CCA) wood treater waste, 2) La Trinidad Mine tailings, ...

  14. Hybrid Polymer-Immobilized Nanosized Pd Catalysts for Hydrogenation Reaction Obtained via Frontal Polymerization

    OpenAIRE

    Anatolii D. Pomogailo; Gulzhian I. Dzhardimalieva

    2013-01-01

    A new approach to the synthesis of mixed-type immobilized catalysts by frontal polymerization of metal-containing monomer in the presence of highly dispersed mineral support has been developed. Synthesis of the acrylamide Pd(II) nitrate complex, Pd(CH2=CHCONH2)2 (NO3)2 (PdAAm), on the SiO2 (Al2O3, C) surface and its consequent frontal polymerization and reduction lead to the formation of organic-inorganic composites with polymer-stabilized Pd nanoparticles. The immobilized metal complexes and...

  15. Time-dependent deformation behavior of polyvinylidene fluoride binder: Implications on the mechanics of composite electrodes

    Science.gov (United States)

    Santimetaneedol, Arnuparp; Tripuraneni, Rajasekhar; Chester, Shawn A.; Nadimpalli, Siva P. V.

    2016-11-01

    The majority of existing battery models that simulate composite electrode behavior assume the binder as a linear elastic material due to lack of a thorough understanding of time-dependent mechanical behavior of binders. Here, thin films of polyvinylidene fluoride binder, prepared according to commercial battery manufacturing method, are subjected to standard monotonic, load-unload, and relaxation tests to characterize the time-dependent mechanical behavior. The strain in the binder samples is measured with the digital image correlation technique to eliminate experimental errors. The experimental data showed that for (charging/discharging) time scales of practical importance, polyvinylidene fluoride behaves more like an elastic-viscoplastic material as opposed to a visco-elastic material; based on this observation, a simple elastic-viscoplastic model, calibrated against the data is adopted to represent the deformation behavior of binder in a Si-based composite electrode; the lithiation/delithiation process of this composite was simulated at different C rates and the stress/strain behavior was monitored. It is observed that the linear elastic assumption of the binder leads to inaccurate results and the time-dependent constitutive behavior of the binder not only leads to accurate prediction of the mechanics but is an essential step towards developing advanced multi-physics models for simulating the degradation behavior of batteries.

  16. Characterization of zirconia-based slurries with different binders for titanium investment casting

    Directory of Open Access Journals (Sweden)

    Zhao Ertuan

    2012-05-01

    Full Text Available The materials and physical properties of primary slurry are crucial to the surface quality of the finished castings, especially for high reactivity titanium alloys. The aim of this study is to investigate the influence of different binders on the physical properties of primary slurry for titanium alloy investment casting. The zirconia-based slurries with different binders were evaluated by comparing the parameters: viscosity, bulk density, plate weight, suspensibility, gel velocity and strength. The results indicate that a higher viscosity of binder leads to a higher viscosity and suspensibility of slurry with the same powder/binder ratio. The retention rate and thickness of primary layer increase with an increase in the viscosity of the slurry, and a higher retention rate is associated with a thicker primary layer. The gel velocity of the slurry is correlated with the gel velocity of the binder. The green strength and the baked strength of the primary layer are determined by the properties of the binder after gel and by the production of the binder after fired, respectively.

  17. Application of Microbial Biopolymers as an Alternative Construction Binder for Earth Buildings in Underdeveloped Countries

    Directory of Open Access Journals (Sweden)

    Ilhan Chang

    2015-01-01

    Full Text Available Earth buildings are still a common type of residence for one-third of the world’s population. However, these buildings are not durable or resistant against earthquakes and floods, and this amplifies their potential harm to humans. Earthen construction without soil binders (e.g., cement is known to result in poor strength and durability performance of earth buildings. Failure to use construction binders is related to the imbalance in binder prices in different countries. In particular, the price of cement in Africa, Middle East, and Southwest Asia countries is extremely high relative to the global trend of consumer goods and accounts for the limited usage of cement in those regions. Moreover, environmental concerns regarding cement usage have recently risen due to high CO2 emissions. Meanwhile, biopolymers have been introduced as an alternative binder for soil strengthening. Previous studies and feasibility attempts in this area show that the mechanical properties (i.e., compressive strength of biopolymer mixed soil blocks (i.e, both 1% xanthan gum and 1% gellan gum satisfied the international criteria for binders used in earthen structures. Economic and market analyses have demonstrated that the biopolymer binder has high potential as a self-sufficient local construction binder for earth buildings where the usage of ordinary cement is restricted.

  18. Comparison of cathode catalyst binders for the hydrogen evolution reaction in microbial electrolysis cells

    KAUST Repository

    Ivanov, Ivan

    2017-06-02

    Nafion is commonly used as a catalyst binder in many types of electrochemical cells, but less expensive binders are needed for the cathodes in microbial electrolysis cells (MECs) which are operated in neutral pH buffers, and reverse electrodialysis stacks (RED),which use thermolytic solutions such as ammonium bicarbonate. Six different binders were examined based on differences in ion exchange properties (anionic: Nafion, BPSH20, BPSH40, S-Radel; cationic: Q-Radel; and neutral: Radel, BAEH) and hydrophobicity based on water uptake (0%, Radel; 17–56% for the other binders). BPSH40 had similar performance to Nafion based on steady-state polarization single electrode experiments in a neutral pH phosphate buffer, and slightly better performance in ammonium bicarbonate. Three different Mo-based catalysts were examined as alternatives to Pt, with MoB showing the best performance under steady-state polarization. In MECs, MoB/BPSH40 performed similarly to Pt with Nafion or Radel binders. The main distinguishing feature of the BPSH40 was that it is very hydrophilic, and thus it had a greater water content (56%) than the other binders (0–44%). These results suggest the binders for hydrogen evolution in MECs should be designed to have a high water content without sacrificing ionic or electronic conductivity in the electrode.

  19. Experimental evaluation on high temperature rheological properties of various fiber modified asphalt binders

    Institute of Scientific and Technical Information of China (English)

    陈筝; 吴少鹏; 朱祖煌; 刘杰胜

    2008-01-01

    High temperature rheological properties of fiber modified asphalt binders and impact of the type and content on such properties were studied.Three types of fiber,including polyester(PET),polyacrylonitrile(PAN) and cellulose(CEL),a control content(0%) and four levels of fiber content(2%,4%,6% and 8% by total asphalt binder mass) were used with asphalt binders.The high temperature rheological properties,consisting of complex modulus(G*) and phase angle δ,were measured using SHRP’s dynamic shear rheometer(DSR) between 46-82 ℃.Experimental results indicate that the changes of G* and tan δ of fiber modified asphalt binders with the increase of test temperature tend to slow down,and the temperature susceptibility is improved obviously compared to that of original asphalt binder.Fiber modification results in the increase of rutting parameter(G*/sin δ) at high temperatures,the decrease of temperature susceptibility,and further improved high temperature performance of asphalt binder.An excellent correlation exhibits between fiber content and high temperature performance of asphalt binder.Moreover,fiber type also has different influences on the improvement of G*/sin δ,G*/sin δ of PET and PAN fiber asphalt binders are both higher than that of CEL fiber,but G*/sin δ of CEL fiber is still higher than that of original asphalt.However,there is a critical fiber content when fibers start to interact with each other.Therefore,based on the critical fiber content and economic consideration,the optimum fiber contents for various fiber-modified asphalt binders are obtained.

  20. Shear resistance properties of TPS modified bitumen binders and asphalt mixtures

    Institute of Scientific and Technical Information of China (English)

    曹庭维; 吴少鹏; 刘聪慧; 张涛

    2008-01-01

    Shear resistance properties of the virgin bitumen and modified bitumen binders with Tafpack Super(TPS) modifier and SBS modified bitumen were discussed.Dynamic shear rheometer(DSR) was used to measure the laboratory creep data for these binders over a wide range of constant shear stresses at 20 ℃ to characterize the shear creep behaviors of all kinds of asphalt binders,and the rutting test system was used to investigate the permanent deformation of porous asphalt mixtures using the above bitumen binders for a fixed compressive stress.The shear strain rate and shear creep modulus were used to characterize the shear creep behavior of the TPS modified bitumen,and the rutting test results were used to show the consistency of porous asphalt mixtures with the bitumen binders.Results indicate that a distinction of shear creep strain can be made among different contents of TPS modified bitumen at the same stress level,where the shear creep strain-time response curve of the SBS modified bitumen binder is between the curves of the 8% TPS and 12% TPS modified bitumen binders.The shear strain rate and the shear creep modulus of the TPS modified bitumen binders are obtained to compare with those of the SBS modified bitumen binder which results in the same trend as the shear creep strain-time response curve.Permanent deformation results of all the porous asphalt mixtures from the rutting test show reasonable agreement with the findings of the shear strain rates and shear creep modulus over the range of shear stress levels.

  1. Influence of microcrystalline wax on properties of MIM multi-component wax matrix binder

    Institute of Scientific and Technical Information of China (English)

    张健; 黄伯云; 李益民; 李松林

    2002-01-01

    The properties of PW-EVA-HDPE binder with the addition of MW were studied. It shows that the addition of MW from 1% to 20%(mass fraction) causes an increase in the tensile strength and a decrease in shrinkage of the binder. After blending PW with MW, the crystallation behavior of wax base changes, which results in fine grain for the binder and more isotropic microstructure for the feedstock. The powder loading capacity increases and homogeneity of feedstock becomes better. The reason of the modification is also discussed.

  2. Polyolefin Backbone Substitution in Binders for Low Temperature Powder Injection Moulding Feedstocks

    Directory of Open Access Journals (Sweden)

    Berenika Hausnerova

    2014-02-01

    Full Text Available This paper reports the substitution of polyolefin backbone binder components with low melting temperature carnauba wax for powder injection moulding applications. The effect of various binder compositions of Al2O3 feedstock on thermal degradation parameters is investigated by thermogravimetric analysis. Within the experimental framework 29 original feedstock compositions were prepared and the superiority of carnauba wax over the polyethylene binder backbone was demonstrated in compositions containing polyethylene glycol as the initial opening agent and governing the proper mechanism of the degradation process. Moreover, the replacement of synthetic polymer by the natural wax contributes to an increase of environmental sustainability of modern industrial technologies.

  3. Burn Rate Studies on AN-Based Propellants: Effect of N-N Bonded Binders.

    Directory of Open Access Journals (Sweden)

    C. Oommen

    1996-12-01

    Full Text Available New epoxy resins having N-N bonds in their structures have been employed as binders for ammonium nitrate (AN-based propellants. The resins have been characterized by various analytical techniques. The effect of the new binders on the burn rates of AN-based compositions including the metallized systems has been examined. The overall enhancement in the burn rate, as compared to that observed with conventional binders, has been explained in terms of the combustion reactivity of the N-N bondwiththe oxidizing speciesproduced duringcombustion. Furtherincreasein burn rate canbe achieved by inclusion of magnesium metal or ammonium perchlorate into these compositions.

  4. Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

    Science.gov (United States)

    Mudge, David W; Johnson, David W; Hawley, Carmel M; Campbell, Scott B; Isbel, Nicole M; van Eps, Carolyn L; Petrie, James J B

    2011-05-13

    Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer), which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more expensive binders and increasing concerns about the risks of

  5. The curious case of zeolite-clay/binder interactions and their consequences for catalyst preparation

    OpenAIRE

    Whiting, Gareth T.; Chowdhury, Abhishek Dutta; Oord, R. van; Paalanen, Pasi; Weckhuysen, Bert M.

    2016-01-01

    Zeolite-based catalyst bodies are commonly employed in a range of important industrial processes. Depending on the binder and shaping method chosen, vast differences in the reactivity, selectivity and stability are obtained. Here, three highly complementary micro-spectroscopic techniques were employed to study zeolite ZSM-5-binder interactions in SiO2-, Al2O3-, SiO2 : Al2O3- (2 : 1 mix) and kaolinite-bound catalyst pellets. We establish how their preparation influences the zeolite-clay/binder...

  6. Study on catalysis effect of TEPB on the curing reaction of HTPB binder system

    Science.gov (United States)

    Chang, S. J.; Tang, J.; Liu, X.; Yan, W.

    2016-07-01

    The catalysis effect of tri (exhoxyphenyl) bismuthine (TEPB) on the curing reaction of HTPB binder system was studied by using DSC method. The curing peak temperatures of the catalyst systems were measured to calculate kinetic parameters by using Kissinger and Crane methods, respectively. Two curing reaction kinetic equations were established. The results show that TEPB has high catalytic activity and can decrease the curing temperature of HTPB binder system, down to 35 °C, in which the optimum volume of TEPB is 0.5% of HTPB binder system.

  7. Influence of crumb rubber and digestion time on the asphalt rubber binders

    OpenAIRE

    Neto, Silvrano Adonias Dantas; De Farias, Márcio Muniz; Pais, Jorge C.; Pereira, Paulo A. A.; Sousa, Jorge B.

    2006-01-01

    This paper shows the results of a study about the mechanical behavior of dense graded asphalt-rubber hot mixes prepared with two different types of asphalt-rubber binders. These asphalt-rubber binders were obtained with penetration grade asphalt (AC 50/70) mixed with 21% and 25% of crumb rubber in weight. The rubber was recycled from unserviceable tires using the ambient grinding process. Hot mixes made with the conventional binder AC 50/70 were also studied for comparison. The...

  8. A Binder Viscosity Effect on the Wet-Wounded Composite Porosity in the Impregnating Bath

    Directory of Open Access Journals (Sweden)

    M. A. Komkov

    2014-01-01

    Full Text Available The aim of this work is to define experimentally an impregnation rate of VM-1 glass fibers and CBM aramid bundles with the epoxy binder EDB-10 using wet method of winding. During the impregnation process of the fibrous fillers by the liquid binder, air is displaced from the interfiber space of fiber and bundle. With the composite product winding a fiber impregnation process is short. That is why gas inclusions or pores are formed in the polymer-fiber compositeThe impregnation rate or porosity of wound material will depend directly on the binder viscosity. To reduce an epoxy binder viscosity temporarily is possible by two ways. The first is to heat a liquid epoxy composition EDB-10 to the maximum possible temperature during the winding process of the product. The second method is to dilute the binder by a solvent, such as acetone or alcohol. However, the solvent reduces its strength.The paper presents experimental data to show the volumetric content of pores in the wound composite affected only by the viscosity of the epoxy binder. Heating a binder allowed us to regulate a changing conditional viscosity of the binder in the impregnating bath for the normal conditions of impregnation. Other impacts on the impregnation and filament-winding processes, such as filler kinks, squeeze, vacuuming binder, highly tensioned winding, and others were not used.Experimentally obtained dependences of the porosity value of wound composite on the conditional viscosity of binder are nonlinear and can be used to design heaters for impregnating devices of winders. The research technique and results can be used in development of technological processes to manufacture composite structures by winding from the other reinforcing fibrous fillers and thermo-active binders.The results show that the volumetric content of pores can significantly vary within 8 - 14 % of material volume. Therefore, to reduce the number of pores in the wound composite to 1-2 %, auxiliary

  9. FTIR spectroscopy of water glass - the binder moulding modified by ZnO nanoparticles

    Directory of Open Access Journals (Sweden)

    A. Bobrowski

    2012-10-01

    Full Text Available The subject of the paper is the determination of the infl uence of the colloidal nanoparticles of zinc oxide on the structure of sodium water glass. Nanoparticles of zinc oxide in ethanol solvent were introduced into the water glass. The modification and structural changes were determined by means of the FT-IR absorption spectra. In order to determine the kind of infl uence: binder-modifier the spectroscopic FTIR analysis of samples of a fresh binder and of a binder hardened for 24 h in the air was performed by means of the spectrometer Digilab Excalibur with a standard DTGS detector.

  10. Cirugía ortognática y rinoplastia en el síndrome de Binder Orthognathic surgery and rhinoplasty in Binder syndrome

    Directory of Open Access Journals (Sweden)

    M. Tito

    2007-04-01

    Full Text Available El síndrome de Binder es una patología caracterizada por hipoplasia nariz-maxilar, ángulo naso-frontal plano, senos frontales hipoplasicos, ausencia de la espina nasal anterior, columela corta y ángulo nasolabial agudo. El tratamiento del los pacientes con síndrome de Binder puede ser ortodóntico o quirúrgico según la gravedad de la malformación. En este trabajo hemos realizado una revision bibliográfica sobre la etiología, el diagnóstico diferential y el tratamiento de la sindrome de Binder y presentamos un caso clínico de un paciente binderiano sometido a intervención de cirugía ortognática y rinoplastia con injerto de cartílago costal para recostruir el dorso y la punta nasal.Binder syndrome is a disorder characterized by nasomaxillary hypoplasia that results in a short nose, a frontonasal angle of almost 180 degrees, hypoplasia of the frontal sinuses, an absent anterior nasal spine, a short columella and an acute nasolabial angle. The patient can be treated orthodontically or surgically depending on the seriousness of the malformation. We review the literature on the etiology, differential diagnosis and treatment of Binder syndrome. We present the case of a boy with this syndrome surgically treated with orthognatic surgery and rhinoplasty with an L-shaped rib cartilage graft.

  11. Organometallic Polymeric Conductors

    Science.gov (United States)

    Youngs, Wiley J.

    1997-01-01

    For aerospace applications, the use of polymers can result in tremendous weight savings over metals. Suitable polymeric materials for some applications like EMI shielding, spacecraft grounding, and charge dissipation must combine high electrical conductivity with long-term environmental stability, good processability, and good mechanical properties. Recently, other investigators have reported hybrid films made from an electrically conductive polymer combined with insulating polymers. In all of these instances, the films were prepared by infiltrating an insulating polymer with a precursor for a conductive polymer (either polypyrrole or polythiophene), and oxidatively polymerizing the precursor in situ. The resulting composite films have good electrical conductivity, while overcoming the brittleness inherent in most conductive polymers. Many aerospace applications require a combination of properties. Thus, hybrid films made from polyimides or other engineering resins are of primary interest, but only if conductivities on the same order as those obtained with a polystyrene base could be obtained. Hence, a series of experiments was performed to optimize the conductivity of polyimide-based composite films. The polyimide base chosen for this study was Kapton. 3-MethylThiophene (3MT) was used for the conductive phase. Three processing variables were identified for producing these composite films, namely time, temperature, and oxidant concentration for the in situ oxidation. Statistically designed experiments were used to examine the effects of these variables and synergistic/interactive effects among variables on the electrical conductivity and mechanical strength of the films. Multiple linear regression analysis of the tensile data revealed that temperature and time have the greatest effect on maximum stress. The response surface of maximum stress vs. temperature and time (for oxidant concentration at 1.2 M) is shown. Conductivity of the composite films was measured for

  12. High temperature structural, polymeric foams from high internal emulsion polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Hoisington, M.A.; Duke, J.R.; Apen, P.G.

    1996-02-01

    In 1982, a high internal phase emulsion (HIPE) polymerization process to manufacture microcellular, polymeric foam systems was patented by Unilever. This patent discloses a polymerization process that occurs in a water-in-oil emulsion in which the water represents at least 76% of the emulsion by volume. The oil phase consists of vinyl monomers such as styrene and acrylates that are crosslinked by divinyl monomers during polymerization. After polymerization and drying to remove the water phase, the result is a crosslinked polymer foam with an open cell microstructure that is homogeneous throughout in terms of morphology, density, and mechanical properties. Since 1982, numerous patents have examined various HIPE polymerized foam processing techniques and applications that include absorbents for body fluids, cleaning materials, and ion exchange systems. All the published HIPE polymerized foams have concentrated on materials for low temperature applications. Copolymerization of styrene with maleic anhydride and N-substituted maleimides to produce heat resistant thermoplastics has been studied extensively. These investigations have shown that styrene will free radically copolymerize with N-substituted maleimides to create an alternating thermoplastic copolymer with a Tg of approximately 200{degrees}C. However, there are many difficulties in attempting the maleimide styrene copolymerization in a HIPE such as lower polymerization temperatures, maleimide solubility difficulties in both styrene and water, and difficulty obtaining a stable HIPE with a styrene/maleimide oil phase. This work describes the preparation of copolymer foams from N-ethylmaleimide and Bis(3-ethyl-5-methyl-4-maleimide-phenyl)methane with styrene based monomers and crosslinking agents.

  13. Topological calculation of key parameters of fibre for production of foam concrete based on cement-free nanostructured binder

    Directory of Open Access Journals (Sweden)

    KHARKHARDIN Anatoly Nikolaevich

    2016-08-01

    Full Text Available Fiber reinforcement is the process of introduction of fibers of different origins into binding system to enhance strength, stress-strain behavior of products and structures. Maximal effect of reinforcing process is possible when optimal parameters (length and consumption of fibre are determined. Moreover one need to consider particle-size composition and hardening process of binding system. In this paper the critical length of natural and sinthesized fibres as well as minimally required content in cellular systems is calculated with the mathematical apparatus of structural topology. As an example the foam concrete based on cement-free nanostructured binder with basalt fibre and microreinforcing constructional polymeric fibre is studied. Fiber diameter, refined with microstructure analysis, accomplished by SEM-microscopy and experimentally determined packing density in loose and compact state are applied as input parameters. Measurement of the fibre topological characteristics with acceptable is accomplished according to material porosity and pore size. So the minimal effective fibre length taking into account homogeneous distribution in bulk of composite matrix is less of 1 mm; minimal fibre consumption is 0,2–0,5 (by wt. %. Irrational optimization leads to unreasonable cost growth of final materials as well as formation of balling inclusions that negatively affects on final performance of composite.

  14. Three-year performance of in-situ mass stabilised contaminated site soils using MgO-bearing binders.

    Science.gov (United States)

    Wang, Fei; Jin, Fei; Shen, Zhengtao; Al-Tabbaa, Abir

    2016-11-15

    This paper provides physical and chemical performances of mass stabilised organic and inorganic contaminated site soils using a new group of MgO-bearing binders over 3 years and evaluated the time-dependent performance during the 3 years. This study took place at a contaminated site in Castleford, UK in 2011, where MgO, ground granulated blastfurnace slag (GGBS) and Portland cement (PC) were mixed with the contaminated soils in a dry form using the ALLU mass mixing equipment. Soil cores were retrieved 40-day, 1-year and 3-year after the treatment. The core quality, strength, and the leaching properties were determined via physical observation, unconfined compressive strength (UCS) and batch leaching tests. After 3-year treatment, the UCS values of ALLU mixes were in the range of 50-250kPa; the leachate concentrations of Cd, Pb, Cu and Zn (except Ni) in all mixes were lower than their drinking water standards; and the leachability of total organics was in the range of 10-105mg/L. No apparent degradation of the mass stabilised materials after 3 years' exposure to the field conditions was found. MgO-GGBS blends were found able to provide higher strength and less leachability of contaminants compared to PC and MgO-only mixes in mass stabilised soils.

  15. Hybrid Organic/Inorganic Coatings Through Dual-Cure Processes: State of the Art and Perspectives

    Directory of Open Access Journals (Sweden)

    Giulio Malucelli

    2016-03-01

    Full Text Available This paper reviews the current state of the art related to the synthesis and characterization of hybrid organic-inorganic (O/I coatings obtained through the exploitation of dual-cure processes, which involve a photo-induced polymerization followed by a thermal treatment: this latter allows the occurrence of sol-gel reactions of suitable alkoxy precursors already embedded in the UV-curable system. After a brief introduction on hybrid organic-inorganic coatings, the first part of the review is focused on the design and feasibility issues provided by the dual-cure method, emphasizing the possibility of tuning the structure of the final hybrid network on the basis of the composition of the starting liquid mixture. Then, some recent examples of hybrid organic-inorganic networks are thoroughly described, showing their potential advances and the application fields to which they can be addressed.

  16. Pickering乳液聚合制备草莓型PSt/SiO_2有机-无机复合微球%Preparation of Raspberry-Like PSt/Si02 Organic-Inorganic Nanocomposite Microspheres Through Pickering Emulsion Polymerization

    Institute of Scientific and Technical Information of China (English)

    张玉红; 董正凤; 王治国; 何培新

    2012-01-01

    Polystyrene /SiO2 composite microspheres were successfully prepared by Pickering emulsion polymerization using a cationic azo initiator (2, 2'-azobis (isobutyramidine) dihydrochloride (AIBA)) in combination with a commercially available glycerol-functionalized ultrafine aqueous silica sol in the absence of any auxiliary comonomer. Transmission electron microscope (TEM) indicates polystyrene/silica particles with raspberry-like morphology. The particle sizes and final silica content range from 190 nm to 300 nm and 28 % to 44 %, respectively. The influences of initial silica content, AIBA content, reaction temperature on the average diameters and silica contents of the composite microspheres were studied. The result indicates that with the initial silica content increase, the diameter of the composite microspheres tends to decrease and the silica contents adsorbed on the latexes surface increase. The silica content increases with the increase of the AIBA amount. With the reaction temperature increase, the average diameter increases, but the variance of silica content is less.%在纳米硅溶胶分散介质中,以苯乙烯(St)为单体,偶氮二异丁脒盐酸盐(AIBA)为引发剂,不添加任何辅助单体,通过Pickering乳液聚合,成功制备了PSt/SiO2有机-无机复合微球,透射电镜研究显示,复合微球具有草莓型形态。所得复合微球粒径在190 nm-300 nm之间,二氧化硅吸附量介于28%-44%之间。研究了初始硅溶胶用量、AIBA用量和反应温度等因素对复合微球粒子粒径和二氧化硅吸附量的影响。结果发现,初始硅溶胶用量增大,复合微球粒径减小、二氧化硅吸附量增大;引发剂用量增加,二氧化硅吸附量增大;反应温度升高,复合微球粒径增大,但对二氧化硅吸附量影响较小。

  17. Electroactivity in Polymeric Materials

    CERN Document Server

    2012-01-01

    Electroactivity in Polymeric Materials provides an in-depth view of the theory of electroactivity and explores exactly how and why various electroactive phenomena occur. The book explains the theory behind electroactive bending (including ion-polymer-metal-composites –IPMCs), dielectric elastomers, electroactive contraction, and electroactive contraction-expansion cycles.  The book also balances theory with applications – how electroactivity can be used – drawing inspiration from the manmade mechanical world and the natural world around us.  This book captures: A complete introduction to electroactive materials including examples and recent developments The theory and applications of numerous topics like electroactive bending of dielectric elastomers and electroactive contraction and expansion New topics, such as biomimetic applications and energy harvesting This is a must-read within the electroactive community, particularly for professionals and graduate students who are interested in the ...

  18. Kinetics of silica polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Weres, O.; Yee, A.; Tsao, L.

    1980-05-01

    The polymerization of silicic acid in geothermal brine-like aqueous solutions to produce amorphous silica in colloidal form has been studied experimentally and theoretically. A large amount of high quality experimental data has been generated over the temperature rang 23 to 100{sup 0}C. Wide ranges of dissolved silica concentration, pH, and sodium chloride concentration were covered. The catalytic effects of fluoride and the reaction inhibiting effects of aluminum and boron were studied also. Two basic processes have been separately studied: the formation of new colloidal particles by the homogeneous nucleation process and the deposition of dissolved silica on pre-existing colloidal particles. A rigorous theory of the formation of colloidal particles of amorphous silica by homogeneous nucleation was developed. This theory employs the Lothe-Pound formalism, and is embodied in the computer code SILNUC which quantitatively models the homogeneous nucleation and growth of colloidal silica particles in more than enough detail for practical application. The theory and code were extensively used in planning the experimental work and analyzing the data produced. The code is now complete and running in its final form. It is capable of reproducing most of the experimental results to within experimental error. It is also capable of extrapolation to experimentally inaccessible conditions, i.e., high temperatures, rapidly varying temperature and pH, etc.

  19. Polymerization of anionic wormlike micelles.

    Science.gov (United States)

    Zhu, Zhiyuan; González, Yamaira I; Xu, Hangxun; Kaler, Eric W; Liu, Shiyong

    2006-01-31

    Polymerizable anionic wormlike micelles are obtained upon mixing the hydrotropic salt p-toluidine hydrochloride (PTHC) with the reactive anionic surfactant sodium 4-(8-methacryloyloxyoctyl)oxybenzene sulfonate (MOBS). Polymerization captures the cross-sectional radius of the micelles (approximately 2 nm), induces micellar growth, and leads to the formation of a stable single-phase dispersion of wormlike micellar polymers. The unpolymerized and polymerized micelles were characterized using static and dynamic laser light scattering, small-angle neutron scattering, 1H NMR, and stopped-flow light scattering. Stopped-flow light scattering was also used to measure the average lifetime of the unpolymerized wormlike micelles. A comparison of the average lifetime of unpolymerized wormlike micelles with the surfactant monomer propagation rate was used to elucidate the mechanism of polymerization. There is a significant correlation between the ratio of the average lifetime to the monomer propagation rate and the average aggregation number of the polymerized wormlike micelles.

  20. Surface glycosylation of polymeric membranes

    Institute of Scientific and Technical Information of China (English)

    DAI ZhengWei; WAN LingShu; XU ZhiKang

    2008-01-01

    Surface glycosylation of polymeric membranes has been inspired by the structure of natural biomembranes. It refers to that glycosyl groups are introduced onto the membrane surface by various strategies, which combine the separation function of the membrane with the biological function of the saccharides in one system. In this review, progress in the surface glycosylation of polymeric membranes is highlighted in two aspects, i.e. the glycosylation methods and the potential applications of the surface-glycosylated membranes.

  1. Chemical Characterization of Lime-Based Binders in Historic Buildings of Latvia

    Science.gov (United States)

    Kirilovica, I.; Gulbe, L.; Vitina, I.; Igaune-Blumberga, S.

    2015-11-01

    The aim of this research is to investigate the chemical composition of stone materials of several local historic buildings with a purpose of elaboration of restoration strategy, including the choice of restoration materials. Most of the examined mortars are lime- based hydraulic mortars, characteristic of the architecture of 19th/20th century. Pure aerial lime binders show reduced compatibility with historic materials, that is why lime binders with pozzolan additive (cement) are an appropriate choice for restoration. In order to examine the changes of hydraulicity (i.e. the property of binders to harden when exposed to water) of perspective restoration binders, a series of blended lime-cement mixtures were synthesized with growing content of cement (up to 10% by weight). A significant relationship between cement content and hydraulic properties has been shown.

  2. Process Development of Porcelain Ceramic Material with Binder Jetting Process for Dental Applications

    Science.gov (United States)

    Miyanaji, Hadi; Zhang, Shanshan; Lassell, Austin; Zandinejad, Amirali; Yang, Li

    2016-03-01

    Custom ceramic structures possess significant potentials in many applications such as dentistry and aerospace where extreme environments are present. Specifically, highly customized geometries with adequate performance are needed for various dental prostheses applications. This paper demonstrates the development of process and post-process parameters for a dental porcelain ceramic material using binder jetting additive manufacturing (AM). Various process parameters such as binder amount, drying power level, drying time and powder spread speed were studied experimentally for their effect on geometrical and mechanical characteristics of green parts. In addition, the effects of sintering and printing parameters on the qualities of the densified ceramic structures were also investigated experimentally. The results provide insights into the process-property relationships for the binder jetting AM process, and some of the challenges of the process that need to be further characterized for the successful adoption of the binder jetting technology in high quality ceramic fabrications are discussed.

  3. Optimum Parameters for the Formulation of Charcoal Briquettes Using Bagasse and Clay as Binder

    National Research Council Canada - National Science Library

    M.S. Rao; B.N. Chikamai; J.M. Onchieku

    2012-01-01

    ... for the formulation of charcoal briquettes for household use tosupplement wood charcoal. In this study briquettes were formulated usingcarbonized bagasse, clay as a binder and molasses as a filler...

  4. Optimum Parameters for the Formulation of Charcoal Briquettes Using Bagasse and Clay as Binder

    National Research Council Canada - National Science Library

    J.M. Onchieku; B.N. Chikamai; M.S. Rao

    2014-01-01

    ... for the formulation of charcoal briquettes for household use tosupplement wood charcoal. In this study briquettes were formulated usingcarbonized bagasse, clay as a binder and molasses as a filler...

  5. Study of Rheological Properties of Bituminous Binders in Middle and High Temperatures

    Directory of Open Access Journals (Sweden)

    Remišová Eva

    2016-05-01

    Full Text Available The bitumen binders in road pavements are exposed traffic loading effect at different climatic conditions. A resistance to these stresses depends on bitumen properties as well. The paper presents rheological properties (G*, δ, ν* determined and compared for four bituminous binders (unmodified and polymer modified bitumen at temperature 46 – 60 (80 °C and dynamic viscosity at temperature 130 – 190 °C (Brookfield viscometer. On the basis of viscosity results it is possible to set optimal production and compaction temperatures. Elastic and viscous behavior of binder in the middle temperature is determined in rheometers. The higher value of complex modulus, the stiffer bitumen binder is able to resist deformation. The greater content of elastic components (e.g. polymer in bitumen varies mainly elastic-viscous properties of primary bitumen.

  6. Tungsten carbide coatings with different binders prepared by low power plasma spray system

    Institute of Scientific and Technical Information of China (English)

    GAO Yang; M.F.Morks; FU Ying-qing

    2004-01-01

    Thermal spraying of cermet coatings is widely used for protection of machining parts against wear and corrosion. These coatings consist of WC particles in metal binders such as Co, Cr and Ni. Three kinds of WC powders with different metal binders (Co, NiCr and CoCr) were sprayed by low power plasma spray system on Al-Si-Cu alloy substrate. Fundamental aspects of sprayed cermet coatings, including (i) the effects of binder type on the coating structure, (ii) the hardness and (iii) the microstructure, were investigated. All cermet coatings have the same phase structure such as WC and W2 C. However, the intensities of these phases are different in each coating, mainly due to the difference in solidification rate in each case. Moreover, the hardness measurements are found to be different in each coating. The results show that, binder type has a significant effect on the physical and mechanical properties of the sprayed coatings.

  7. Some aspects on improvement of water resistant perfornace of gypsum binders

    Directory of Open Access Journals (Sweden)

    Fomina Ekaterina

    2016-01-01

    Full Text Available The study reports that control of water resistant and strength performance of composite binder can be accomplished by using nanostructured gypsum silicate binder and portland cement and reduction of calcium sulfate dihydrate. Formation of an arranged more dense packing in crystal matrix of binder structure can be achieved through polydispersity of nanostructured silicon component. Highly reactive silica particles participate in synthesis of microcrystalline compounds such as hydroxylellestadite and serve as nucleation sites providing an increase of surface contact area between crystal structures. Cement in the system provides conditions to synthesis of stable flat-like hydroxysulfoaluminates. Upon hydration of a binder crystals of calcium sulfate dihydrate impound to a mass of water resistant crystalhydrate new formations, type and morphology of which promotes decreasing of intercrystal porosity followed by density, strength and water resistance increase of the composite.

  8. Testing a Novel Geopolymer Binder as a Refractory Material for Rocket Plume Environments at SSC Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The project involved the development and testing of a new alumina-silicate based multi-purpose, cost-effective, ‘green’ cementitious binder (geopolymer)...

  9. Poly(lactic acid) degradable plastics, coatings, and binders

    Energy Technology Data Exchange (ETDEWEB)

    Bonsignore, P.V.; Coleman, R.D.; Mudde, J.P.

    1992-01-01

    Biochemical processes to derive value from the management of high carbohydrate food wastes, such as potato starch, corn starch, and cheese whey permeate, have typically been limited to the production of either ethanol or methane. Argonne National Laboratory (ANL) believes that lactic acid presents an attractive option for an alternate fermentation end product, especially in light of lactic acids' being a viable candidate for conversion to environmentally safe poly(lactic acid) (PLA) degradable plastics, coatings, and binders. Technology is being developed at ANL to permit a more cost effective route to modified high molecular weight PLA. Preliminary data on the degradation behavior of these modified PLAs shows the retention to the inherent hydrolytic degradability of the PLA modified, however, by introduced compositional variables. A limited study was done on the hydrolytic stability of soluble oligomers of poly(L-lactic acid). Over a 34 day hold period, water-methanol solutions of Pl-LA oligomers in the 2-10 DP range retained some 75% of their original molecular weight.

  10. Poly(lactic acid) degradable plastics, coatings, and binders

    Energy Technology Data Exchange (ETDEWEB)

    Bonsignore, P.V.; Coleman, R.D.; Mudde, J.P.

    1992-05-01

    Biochemical processes to derive value from the management of high carbohydrate food wastes, such as potato starch, corn starch, and cheese whey permeate, have typically been limited to the production of either ethanol or methane. Argonne National Laboratory (ANL) believes that lactic acid presents an attractive option for an alternate fermentation end product, especially in light of lactic acids` being a viable candidate for conversion to environmentally safe poly(lactic acid) (PLA) degradable plastics, coatings, and binders. Technology is being developed at ANL to permit a more cost effective route to modified high molecular weight PLA. Preliminary data on the degradation behavior of these modified PLAs shows the retention to the inherent hydrolytic degradability of the PLA modified, however, by introduced compositional variables. A limited study was done on the hydrolytic stability of soluble oligomers of poly(L-lactic acid). Over a 34 day hold period, water-methanol solutions of Pl-LA oligomers in the 2-10 DP range retained some 75% of their original molecular weight.

  11. Recent developments in binder design for advanced media

    Science.gov (United States)

    Kim, K. J.; Farkas, J.; Hasman, D.; Miller, T.; Zellia, J.; Jacobs, P.

    1999-03-01

    This study is aimed to examine the technical issue, the rheological requirements, in accomplishing successful processing of the dispersion made with wetting binders to produce tapes with excellent mechanical properties. The results indicate that the dispersions made with DTPU or NTPU (new dispersing TPU for metal pigments), can be characterized using RFS 8400 and Bolin CSM. For this type of dispersion, a higher strain is required to start flow or to break the primary structure, a wider range of shear rate is needed for the structural breakdown. It also shows that the recovery time is shorter with longer time to reach a steady state that is a lower recovery compliance level. G'/ G″ cross-over point was defining the needed strain level and the strain rate for the structural breakdown. It is expected that the results of the study could be applied to define the mechanical properties of the final tape affected by various operations such as mixing/agitation, high coating speed, drying/calendering, and curing and high speed duplicating process.

  12. Quality of buffalo meat burger containing legume flours as binders.

    Science.gov (United States)

    Modi, V K; Mahendrakar, N S; Narasimha Rao, D; Sachindra, N M

    2004-01-01

    The effect of addition of different decorticated legume flours, viz., soya bean, bengal gram, green gram and black gram, on the quality of buffalo meat burger was studied. The burgers consisted of optimized quantities of roasted or unroasted legume flour, spices and common salt. Inclusion of roasted black gram flour registered the highest yield of 95.7%, lowest shrinkage of 5% and lowest fat absorption of 26.6% on frying. Protein content of 18-20% was highest in the soya flour formulation. Free fatty acid (FFA) values (as% oleic) increased from 14.3 to 17.3 in freshly prepared samples (before frying) to 16.0-19.4 in 4 m frozen (-16±2 °C) stored samples and fried samples had about 25% lower FFA values. Formulations with roasted flours registered lower thiobarbituric acid (TBA) values (mg malonaldehyde/kg sample) of 0.6-1.5 as against 0.6-2.1 for unroasted flours before frying. The burgers prepared with any of these binders were organoleptically acceptable even after storage at -16±2 °C for 4 months., However, the burger with black gram dhal (dehulled split legume) flour had better sensory quality attributes compared to other legumes.

  13. Study on the hardening mechanism of cement asphalt binder

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The hydration and hardening mechanism of cement asphalt binder(CAB) was studied.The early hydration process,hydration products and paste microstructure of CAB made by Portland cement and anionic asphalt emulsion were investigated by calorimetry,X-ray diffraction,and environmental scanning electron microscopy.The early hydration process of CAB can be characterized as 5 stages similar to those of Portland cement.There is no chemical reaction detected between cement and asphalt,hence no new hydration products other than those of Portland cement are produced.The hardening of CAB begins with the hydration of cement.When the hydration of cement comes into the acceleration period and its exothermic rate comes to the maximum,the coalescence of asphalt particles in asphalt emulsion is triggered.In the hardened system of CAB,it was found that the hydration products of cement form the skeleton and are covered by the continuous asphalt film.They formed an interpenetrating network system.The emulsifiers in the asphalt emulsion may retard the hydration process of cement.

  14. Inorganic Reaction Mechanisms. Part I

    Science.gov (United States)

    Cooke, D. O.

    1976-01-01

    Provides a collection of data on the mechanistic aspects of inorganic chemical reactions. Wherever possible includes procedures for classroom demonstration or student project work. The material covered includes gas phase reactions, reactions in solution, mechanisms of electron transfer, the reaction between iron III and iodine, and hydrolysis. (GS)

  15. Inorganic nanomedicine--part 1.

    Science.gov (United States)

    Sekhon, Bhupinder S; Kamboj, Seema R

    2010-08-01

    Inorganic nanomedicine refers to the use of inorganic or hybrid nanomaterials and nanosized objects to achieve innovative medical breakthroughs for drug and gene discovery and delivery, discovery of biomarkers, and molecular diagnostics. Potential uses for fluorescent quantum dots include cell labeling, biosensing, in vivo imaging, bimodal magnetic-luminescent imaging, and diagnostics. Biocompatible quantum dot conjugates have been used successfully for sentinel lymph node mapping, tumor targeting, tumor angiogenesis imaging, and metastatic cell tracking. Magnetic nanowires applications include biosensing and construction of nucleic acids sensors. Magnetic cell therapy is used for the repair of blood vessels. Magnetic nanoparticles (MNPs) are important for magnetic resonance imaging, drug delivery, cell labeling, and tracking. Superparamagnetic iron oxide nanoparticles are used for hyperthermic treatment of tumors. Multifunctional MNPs applications include drug and gene delivery, medical imaging, and targeted drug delivery. MNPs could have a vital role in developing techniques to simultaneously diagnose, monitor, and treat a wide range of common diseases and injuries. From the clinical editor: This review serves as an update about the current state of inorganic nanomedicine. The use of inorganic/hybrid nanomaterials and nanosized objects has already resulted in innovative medical breakthroughs for drug/gene discovery and delivery, discovery of biomarkers and molecular diagnostics, and is likely to remain one of the most prolific fields of nanomedicine.

  16. Characterization of hydrocarbon emissions from green sand foundry core binders by analytical pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Yujue Wang; Fred S. Cannon; Magda Salama; Jeff Goudzwaard; James C. Furness [Pennsylvania State University, University Park, PA (United States). Department of Civil and Environmental Engineering

    2007-11-15

    Analytical pyrolysis was conducted to compare the hydrocarbon and greenhouse gas emissions of three foundry sand binders: (a) conventional phenolic urethane resin, (b) biodiesel phenolic urethane resin, and (c) collagen-based binder. These binders are used in the metal casting industry to create internal cavities within castings. Green sand contains silica sand, clay, carbonaceous additives (eg bituminous coal) and water. The core samples were flash pyrolyzed in a Curie-point pyrolyzer at 920{sup o}C with a heating rate of about 3000{sup o}C/sec. This simulated some key features of the fast heating conditions that the core binders would experience at the metal-core interface when molten metal is poured into green sand molds. The core samples were also pyrolyzed in a thermogravimetric analyzer (TGA) from ambient temperature to 1000{sup o}C with a heating rate of 30{sup o}C/min, and this simulated key features of the slow heating conditions that the core binders would experience at distances that are further away from the metal-core interface during casting cooling. Hydrocarbon emissions from flash pyrolysis were analyzed with a gas chromatography-flame ionization detector, while hydrocarbon and greenhouse gas emissions from TGA pyrolysis were monitored with mass spectrometry. The prominent hazardous air pollutant emissions during pyrolysis of the three binders were phenol, cresols, benzene, and toluene for the conventional phenolic urethane resin and biodiesel resin, and benzene and toluene for the collagen-based binder. Bench-scale analytical pyrolysis techniques could be a useful screening tool for the foundries to compare the relative emissions of alternative core binders and to choose proper materials in order to comply with air-emission regulations. 20 refs., 4 figs., 1 tab.

  17. Characterization of zirconia-based slurries with different binders for titanium investment casting

    OpenAIRE

    Zhao Ertuan; Kong Fantao; Chen Yanfei

    2012-01-01

    The materials and physical properties of primary slurry are crucial to the surface quality of the finished castings, especially for high reactivity titanium alloys. The aim of this study is to investigate the influence of different binders on the physical properties of primary slurry for titanium alloy investment casting. The zirconia-based slurries with different binders were evaluated by comparing the parameters: viscosity, bulk density, plate weight, suspensibility, gel velocity and streng...

  18. Water-soluble binders for MCMB carbon anodes for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Courtel, Fabrice M.; Niketic, Svetlana; Duguay, Dominique; Abu-Lebdeh, Yaser; Davidson, Isobel J. [National Research Council Canada, 1200 Montreal Road, Ottawa, Ontario, K1A 0R6 (Canada)

    2011-02-15

    We have investigated the suitability of four different binders for the conventional mesocarbon microbeads (MCMBs) anode material in Li-ion batteries. Unlike the conventional polyvinylidene fluoride (PVDF), the binders were water soluble and were either cellulose based, such as the lithium and sodium salts of carboxymethyl cellulose (NaCMC, and LiCMC) and Xanthan Gum (XG), or the conjugated polymer: poly(3,4-ethylendioxythiophene) (PEDOT, a.k.a. Baytron). All binders were commercially available except LiCMC, which was synthesized and characterized by FTIR and NMR. Thermal studies of the binders by TGA and DSC showed that, in air, the binders have a broad melting event at 100-150 C, with an onset temperature for decomposition above 220 C. Li/MCMB half-cell batteries were assembled using the studied binders. Slow scan voltammograms of all cells showed characteristic lithium insertion and de-insertion peaks including that of the SEI formation which was found to be embedded into the insertion peaks during the first cycle. Cycling of the cells showed that the one containing XG binder gave the highest capacities reaching 350 mAh g{sup -1} after 100 cycles at C/12, while the others gave comparable capacities to those of the conventional binder PVDF. The rate capabilities of cells were examined and found to perform well up to the studied C/2 rate with more than 50% capacity retained. Further studies of the XG-based MCMB electrodes were performed and concluded that an optimal thickness of 300-365 {mu}m gave the highest capacities and sustained high C-rates. (author)

  19. A Review on Decomposition Deflagration of Oxidizer and Binders in Composite Solid Propellants

    Directory of Open Access Journals (Sweden)

    K. Kishore

    1979-01-01

    Full Text Available Binder and oxidizer decomposition play very significant role during the combustion of composite solid propellants. Ammonium perchlorate (AP is the practical oxidizer in composite propellant formulations. Available information on binder decomposition in general and AP decomposition in particular have been collected and reviewed from the viewpoint of their application in propellants. This review may be useful in understanding the mechanism of propellant combustion.

  20. A new low carbon cementitious binder for stabilising weak ground conditions through deep soil mixing.

    OpenAIRE

    Sargent, P.; Hughes, P. N.; Rouainia, M.

    2016-01-01

    Soft alluvial soils present unfavourable conditions for engineering developments due to their poor bearing capacities and high potential for experiencing shrinkage and swelling. This paper focusses on deep dry soil mixing (DDSM), which introduces cementitious binders to soft soils via a rotating auger drill, thereby producing soil-cement columns. Ordinary Portland cement (CEM-I) is globally used across the construction industry and is the most commonly used binder for DDSM applications due to...

  1. Research of gypsum binder of phosphogypsum and dry mortar on its basis

    OpenAIRE

    Казимагомедов, Ибрагим Эмирчубанович; Дехтярюк, Ольга Игоревна

    2015-01-01

    Gypsum binder was received by the method of intensive dehydration and the influence of admixture in phosphogypsum on the hydration process of gypsum binder was researched. Phase composition of phosphogypsum before and after calcination, using XFA, IR-spectroscopy and crystal optic analysis was defined. Dry mortar for plaster of interior walls of buildings on the basis of CaSO4·0,5H2O obtained from phosphogypsum is investigated. Its advantages and physical and chemical characteristics are shown

  2. AQUEOUS STABLE FREE RADICAL POLYMERIZATION PROCESSES

    Institute of Scientific and Technical Information of China (English)

    Andrea R. Szkurhan; Michael K. Georges

    2004-01-01

    An overview of aqueous polymerizations, which include emulsion, miniemulsion and suspension polymerizations,under stable free radical polymerization (SFRP) conditions is presented. The success of miniemulsion and suspension SFRP polymerizations is contrasted with the difficulties associated with obtaining a stable emulsion polymerization. A recently developed unique microprecipitation technique is referenced as a means of making submicron sized particles that can be used to achieve a stable emulsion SFRP process.

  3. OPTIMIZING THE COMPOSITION AND THE FEATURES OF GYPSUM BINDER PRODUCED IN A KETTLE

    Directory of Open Access Journals (Sweden)

    Pustovgar Andrey Petrovich

    2016-06-01

    Full Text Available The authors considered the gypsum binder obtained in a kettle SMA-158A in the enterprise LLC “MaykopGipsStroy”. The initial gypsum binder burnt at a temperature of 120 °Сwith the following unloading out of the kettle possessed unstable physical, mechanical and operational characteristics, that’s why the grade of gypsum binder was changed from G4-AII to G5-BII for different lots, which greatly reduced its application in the composition of dry mortars. It was stated, that instability of the features of gypsum binder is determined by the essential underburning of the system, which was characterized by residual content of calcium sulfate dihydrate in amount from 2 to 7 % by weight. In frames of the investigation the authors succeeded in raising the grade of the produced gypsum binder (from G4-5 to G6 due to optimization of the technological parameters of the burning process, as well as to stabilize the composition and features, to lay down temperature and time parameters allowing to control the technological process in order to obtain the gypsum binder with specified characteristics.

  4. Application of gelatin as a binder for the sulfur cathode in lithium-sulfur batteries

    Energy Technology Data Exchange (ETDEWEB)

    Sun Jing [Department of Material Science and Engineering, Beijing University of Chemical Technology, 15 BeiSanhuan East Road, Beijing 100029 (China); Huang Yaqin [Department of Material Science and Engineering, Beijing University of Chemical Technology, 15 BeiSanhuan East Road, Beijing 100029 (China)], E-mail: huangyaqin9@sina.com; Wang Weikun; Yu Zhongbao; Wang Anbang; Yuan Keguo [Military Power Sources Research and Development Center, Chemical Defense Institute, 35 Huayuan North Road, Beijing 100083 (China)

    2008-10-15

    Gelatin, a natural biological macromolecule, was successfully used as a new binder in place of poly(ethylene oxide) (PEO) in the fabrication of the sulfur cathode in lithium-sulfur batteries. The structure and electrochemical performance of the two types of sulfur cathodes, with gelatin and PEO as binders, respectively, were compared in 1 M LiClO{sub 4} DME/DOL (V/V = 1/1) electrolyte. The results showed that the gelatin binder had multifunctional effects on the sulfur cathode: it not only functioned as a highly adhesive agent and an effective dispersion agent for the cathode materials, but also an electrochemically stable binder. The gelatin binder-sulfur cathode achieved a high initial capacity of 1132 mAh g{sup -1}, and remained at a reversible capacity of 408 mAh g{sup -1} after 50 cycles, all of which were better than with the PEO binder-sulfur cathode under the same conditions.

  5. Application of gelatin as a binder for the sulfur cathode in lithium-sulfur batteries

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Jing; Huang, Yaqin [Department of Material Science and Engineering, Beijing University of Chemical Technology, 15 BeiSanhuan East Road, Beijing 100029 (China); Wang, Weikun; Yu, Zhongbao; Wang, Anbang; Yuan, Keguo [Military Power Sources Research and Development Center, Chemical Defense Institute, 35 Huayuan North Road, Beijing 100083 (China)

    2008-10-15

    Gelatin, a natural biological macromolecule, was successfully used as a new binder in place of poly(ethylene oxide) (PEO) in the fabrication of the sulfur cathode in lithium-sulfur batteries. The structure and electrochemical performance of the two types of sulfur cathodes, with gelatin and PEO as binders, respectively, were compared in 1 M LiClO{sub 4} DME/DOL (V/V = 1/1) electrolyte. The results showed that the gelatin binder had multifunctional effects on the sulfur cathode: it not only functioned as a highly adhesive agent and an effective dispersion agent for the cathode materials, but also an electrochemically stable binder. The gelatin binder-sulfur cathode achieved a high initial capacity of 1132 mAh g{sup -1}, and remained at a reversible capacity of 408 mAh g{sup -1} after 50 cycles, all of which were better than with the PEO binder-sulfur cathode under the same conditions. (author)

  6. Effects of an abdominal binder and electrical stimulation on cough in patients with spinal cord injury.

    Science.gov (United States)

    Lin, K H; Lai, Y L; Wu, H D; Wang, T Q; Wang, Y H

    1998-04-01

    We explored the effect of an abdominal binder, with or without electrical stimulation, on peak expiratory flow rate (PEFR) in 12 paraplegics with complete thoracic cord (T2-T12) injury (mean age 36.0 +/- 1.5 yr) and 12 quadriplegics with complete cervical cord (C4-C8) injury (mean age 36.2 +/- 1.9 yr). The cough was assessed by measuring the PEFR during forceful expiration in a sitting position. The subjects underwent the following experimental maneuvers in a random order with a 10-minute interval between any two maneuvers: 1) voluntary coughing, 2) voluntary coughing with an abdominal binder, and 3) voluntary coughing with an abdominal binder and electrical stimulation. The electrical stimulator (50 Hz with 300 microseconds pulse width) was applied to the abdominal wall. Data were analyzed using multivariate analysis of variance for repeated measures. The abdominal binder did not significantly increase PEFR in either paraplegics or quadriplegics; the abdominal binder combined with electrical stimulation significantly increased PEFR by 15% in the paraplegics and 18% in the quadriplegics. These results indicate that electrical stimulation combined with an abdominal binder improves the cough ability in patients with cervical or thoracic spinal cord injury.

  7. Analysis of the binder yield energy test as an indicator of fatigue behaviour of asphalt mixes

    Science.gov (United States)

    O’Connell, Johan; Mturi, Georges A. J.; Komba, Julius; Du Plessis, Louw

    2017-09-01

    Empirical binder testing has increasingly failed to predict pavement performance in South Africa, with fatigue cracking being one of the major forms of premature pavement distress. In response, it has become a national aspiration to incorporate a performance related fatigue test into the binder specifications for South Africa. The Binder Yield Energy Test (BYET) was the first in a series of tests analysed for its potential to predict the fatigue performance of the binder. The test is performed with the dynamic shear rheometer, giving two key parameters, namely, yield energy and shear strain at maximum shear stress (γτmax). The objective of the investigation was to perform a rudimentary evaluation of the BYET; followed by a more in-depth investigation should the initial BYET results prove promising. The paper discusses the results generated from the BYET under eight different conditions, using six different binders. The results are then correlated with four point bending beam fatigue test results obtained from asphalt mix samples that were manufactured from the same binders. Final results indicate that the BYET is not ideal as an indicator of fatigue performance.

  8. Small things make a big difference: binder effects on the performance of Li and Na batteries.

    Science.gov (United States)

    Chou, Shu-Lei; Pan, Yuede; Wang, Jia-Zhao; Liu, Hua-Kun; Dou, Shi-Xue

    2014-10-14

    Li and Na batteries are very important as energy storage devices for electric vehicles and smart grids. It is well known that, when an electrode is analysed in detail, each of the components (the active material, the conductive carbon, the current collector and the binder) makes a portion of contribution to the battery performance in terms of specific capacity, rate capability, cycle life, etc. However, there has not yet been a review on the binder, though there are already many review papers on the active materials. Binders make up only a small part of the electrode composition, but in some cases, they play an important role in affecting the cycling stability and rate capability for Li-ion and Na-ion batteries. Poly(vinylidene difluoride) (PVDF) has been the mainstream binder, but there have been discoveries that aqueous binders can sometimes make a battery perform better, not to mention they are cheaper, greener, and easier to use for electrode fabrication. In this review, we focus on several kinds of promising electrode materials, to show how their battery performance can be affected significantly by binder materials: anode materials such as Si, Sn and transitional metal oxides; cathode materials such as LiFePO4, LiNi1/3Co1/3Mn1/3O2, LiCoO2 and sulphur.

  9. Essential work of fracture approach to fatigue grading of asphalt binders

    Science.gov (United States)

    Andriescu, Adrian

    The main objective of this thesis was to apply failure mechanics principles to the characterization of fatigue cracking of asphalt pavements and to identify the correlations between the pavement performance and the composition of binders. The essential work of fracture (EWF) method developed herein is an energy-based testing approach used for the fracture characterization of ductile materials. Developed for both binders and asphalt mixtures, the method provides fundamental parameters, such as specific essential work of fracture and critical tip opening displacement, as potential candidates for a better fatigue specification. It was shown that binders from different sources and with the same performance grade can have very different levels of fatigue susceptibility depending on their manufacturing method and hence failure properties. Also, the currently used binder loss modulus as developed by the Strategic Highway Research Program does not correlate with the newly proposed fracture mechanics based parameters. An extensive theological and ductile failure investigation on a large interval of testing conditions was performed for a group of binders that are used in the recently built test sections of Highway 655 in northern Ontario. It was found that the shift factors used in the construction of the master curves of the ductile fracture parameters differ from the shift factors of the rheological master curves. The difference was attributed to the response of the internal structure of the binder at the high strain levels that precede the failure phenomenon.

  10. Advancing the Use of Secondary Inputs in Geopolymer Binders for Sustainable Cementitious Composites: A Review

    Directory of Open Access Journals (Sweden)

    Esther Obonyo

    2011-02-01

    Full Text Available Because of concerns over the construction industry‘s heavy use of cement and the general dissatisfaction with the performance of building envelopes with respect to durability, there is a growing demand for a novel class of ―green‖ binders. Geopolymer binders have re-emerged as binders that can be used as a replacement for Portland cement given their numerous advantages over the latter including lower carbon dioxide emissions, greater chemical and thermal resistance, combined with enhanced mechanical properties at both normal and extreme exposure conditions. The paper focuses on the use of geopolymer binders in building applications. It discusses the various options for starting materials and describes key engineering properties associated with geopolymer compositions that are ideal for structural applications. Specific properties, such as compressive strength, density, pore size distribution, cumulative water absorption, and acid resistance, are comparable to the specifications for structures incorporating conventional binders. This paper presents geopolymer binders, with their three dimensional microstructure, as material for structural elements that can be used to advance the realization of sustainable building systems.

  11. Tapioca binder for porous zinc anodes electrode in zinc–air batteries

    Directory of Open Access Journals (Sweden)

    Mohamad Najmi Masri

    2015-07-01

    Full Text Available Tapioca was used as a binder for porous Zn anodes in an electrochemical zinc-air (Zn-air battery system. The tapioca binder concentrations varied to find the optimum composition. The effect of the discharge rate at 100 mA on the constant current, current–potential and current density–power density of the Zn-air battery was measured and analyzed. At concentrations of 60–80 mg cm−3, the tapioca binder exhibited the optimum discharge capability, with a specific capacity of approximately 500 mA h g−1 and a power density of 17 mW cm−2. A morphological analysis proved that at this concentration, the binder is able to provide excellent binding between the Zn powders. Moreover, the structure of Zn as the active material was not affected by the addition of tapioca as the binder, as shown by the X-ray diffraction analysis. Furthermore, the conversion of Zn into ZnO represents the full utilization of the active material, which is a good indication that tapioca can be used as the binder.

  12. Polymeric materials for neovascularization

    Science.gov (United States)

    DeVolder, Ross John

    Revascularization therapies have emerged as a promising strategy to treat various acute and chronic wounds, cardiovascular diseases, and tissue defects. It is common to either administer proangiogenic growth factors, such as vascular endothelial growth factor (VEGF), or transplant cells that endogenously express multiple proangiogenic factors. Additionally, these strategies utilize a wide variety of polymeric systems, including hydrogels and biodegradable plastics, to deliver proangiogenic factors in a sophisticated manner to maintain a sustained proangiogenic environment. Despite some impressive results in rebuilding vascular networks, it is still a challenging task to engineer mature and functional neovessels in target tissues, because of the increasing complexities involved with neovascularization applications. To resolve these challenges, this work aims to design a wide variety of proangiogenic biomaterial systems with tunable properties used for neovascularization therapies. This thesis describes the design of several biomaterial systems used for the delivery of proangiogenic factors in neovascularization therapies, including: an electrospun/electrosprayed biodegradable plastic patch used for directional blood vessel growth (Chapter 2), an alginate-g-pyrrole hydrogel system that biochemically stimulates cellular endogenous proangiogenic factor expression (Chapter 3), an enzyme-catalyzed alginate-g-pyrrole hydrogel system for VEGF delivery (Chapter 4), an enzyme-activated alginate-g-pyrrole hydrogel system with systematically controllable electrical and mechanical properties (Chapter 5), and an alginate-g-pyrrole hydrogel that enables the decoupled control of electrical conductivity and mechanical rigidity and is use to electrically stimulate cellular endogenous proangiogenic factor expression (Chapter 6). Overall, the biomaterial systems developed in this thesis will be broadly useful for improving the quality of a wide array of molecular and cellular based

  13. Organic/inorganic nanocomposite polymer electrolyte

    Institute of Scientific and Technical Information of China (English)

    Li Qi; Shao Jun Dong

    2007-01-01

    The organic/inorganic nanocomposites polymer electrolytes were designed and synthesized. The organic/inorganic nanocom posites membrane materials and their lithium salt complexes have been found thermally stable below 200 ℃. The conductivity of the organic/inorganic nanocomposites polymer electrolytes prepared at room temperature was at magnitude range of 10-6 S/cm.

  14. Cytocompatible and multifunctional polymeric nanoparticles for transportation of bioactive molecules into and within cells

    Science.gov (United States)

    Ishihara, Kazuhiko; Chen, Weixin; Liu, Yihua; Tsukamoto, Yuriko; Inoue, Yuuki

    2016-01-01

    Abstract Multifunctional polymeric nanoparticles are materials with great potential for a wide range of biomedical applications. For progression in this area of research, unfavorable interactions of these nanoparticles with proteins and cells must be avoided in biological environments, for example, through treatment of the nanoparticle surfaces. Construction of an artificial cell membrane structure based on polymers bearing the zwitterionic phosphorylcholine group can prevent biological reactions at the surface effectively. In addition, certain bioactive molecules can be immobilized on the surface of the polymer to generate enough affinity to capture target biomolecules. Furthermore, entrapment of inorganic nanoparticles inside polymeric matrices enhances the nanoparticle functionality significantly. This review summarizes the preparation and characterization of cytocompatible and multifunctional polymeric nanoparticles; it analyzes the efficiency of their fluorescence function, the nature of the artificial cell membrane structure, and their performance as in-cell devices; and finally, it evaluates both their chemical reactivity and effects in cells. PMID:27877883

  15. Supported Catalysts Useful in Ring-Closing Metathesis, Cross Metathesis, and Ring-Opening Metathesis Polymerization

    Directory of Open Access Journals (Sweden)

    Jakkrit Suriboot

    2016-04-01

    Full Text Available Ruthenium and molybdenum catalysts are widely used in synthesis of both small molecules and macromolecules. While major developments have led to new increasingly active catalysts that have high functional group compatibility and stereoselectivity, catalyst/product separation, catalyst recycling, and/or catalyst residue/product separation remain an issue in some applications of these catalysts. This review highlights some of the history of efforts to address these problems, first discussing the problem in the context of reactions like ring-closing metathesis and cross metathesis catalysis used in the synthesis of low molecular weight compounds. It then discusses in more detail progress in dealing with these issues in ring opening metathesis polymerization chemistry. Such approaches depend on a biphasic solid/liquid or liquid separation and can use either always biphasic or sometimes biphasic systems and approaches to this problem using insoluble inorganic supports, insoluble crosslinked polymeric organic supports, soluble polymeric supports, ionic liquids and fluorous phases are discussed.

  16. Photocatalytic polymerization induced by a transparent anatase titania aqueous sol and fabrication of polymer composites

    Directory of Open Access Journals (Sweden)

    2010-06-01

    Full Text Available The surface modification of the anatase titania nanoparticles prepared via a controlled nonhydrolytic sol-gel process is achieved by the formation of the bidentate coordination between titania and methacrylic acid (MAA molecules. The in situ photocatalytic polymerization of methyl methacrylate (MMA monomer is initiated by surface modified anatase titania nanoparticles under Xe lamp irradiation. A variety of techniques including differential scanning calorimetry (DSC, thermo-gravimetric analysis (TGA and scanning electron microscopy (SEM are employed to characterize the resulting materials. The glass transition temperatures and the thermal stabilities of polymethyl methacrylate (PMMA composite materials prepared via photocatalytic polymerization are enhanced compared with pure polymer. The partial aggregation of titania nanoparticles in PMMA composite films is derived from the surface polymerization of MMA, which makes the inorganic particles hydrophobic and drives them to the water/oil interfaces.

  17. A new specific polymeric material for mercury speciation: Application to environmental and food samples.

    Science.gov (United States)

    Zarco-Fernández, S; Mancheño, M J; Muñoz-Olivas, R; Cámara, C

    2015-10-15

    A new polymeric material (Patent: P201400535) highly specific for mercury is presented. Its great capability to pre-concentrate and selectively elute inorganic mercury and methylmercury are the main figures of merit. The polymer can be reused several times. To our knowledge, this is the only polymer proposed in the literature for direct inorganic mercury and methylmercury speciation without need of chromatography or quantification by difference. The polymer formation is based on the reaction of a vinyl derivative of 8-hydroxiquinoline as monomer, and 2-(Methacryloylamino) ethyl 2-Methyl Acrylate (NOBE) as co-monomer. Random radical polymerization by the precipitation method was carried out using Azobisisobutyronitrile (AIBN) as initiator. The polymer was characterized by SEM and FTIR. Adsorption binding isotherms were evaluated using Langmuir and Freundlich models, showing high adsorption capacity for both inorganic and organic mercury species. The polymer was employed to sequentially determine inorganic mercury and methylmercury, using a solid phase extraction (SPE) scheme. Cross reactivity of several ions, as well as matrix effects from a high saline matrix like seawater was irrelevant as the retained fractions mostly eluted during the washing step. The procedure was first validated by analyzing a certified reference material (BCR 464) and finally applied to commercial fish samples. The speciation proposed procedure is cheap, fast, and easy to use and minimizes reagents waste.

  18. Stereospecific olefin polymerization catalysts

    Science.gov (United States)

    Bercaw, John E.; Herzog, Timothy A.

    1998-01-01

    A metallocene catalyst system for the polymerization of .alpha.-olefins to yield stereospecific polymers including syndiotactic, and isotactic polymers. The catalyst system includes a metal and a ligand of the formula ##STR1## wherein: R.sup.1, R.sup.2, and R.sup.3 are independently selected from the group consisting of hydrogen, C.sub.1 to C.sub.10 alkyl, 5 to 7 membered cycloalkyl, which in turn may have from 1 to 3 C.sub.1 to C.sub.10 alkyls as a substituent, C.sub.6 to C.sub.15 aryl or arylalkyl in which two adjacent radicals may together stand for cyclic groups having 4 to 15 carbon atoms which in turn may be substituted, or Si(R.sup.8).sub.3 where R.sup.8 is selected from the group consisting of C.sub.1 to C.sub.10 alkyl, C.sub.6 to C.sub.15 aryl or C.sub.3 to C.sub.10 cycloalkyl; R.sup.4 and R.sup.6 are substituents both having van der Waals radii larger than the van der Waals radii of groups R.sup.1 and R.sup.3 ; R.sup.5 is a substituent having a van der Waals radius less than about the van der Waals radius of a methyl group; E.sup.1, E.sup.2 are independently selected from the group consisting of Si(R.sup.9).sub.2, Si(R.sup.9).sub.2 --Si(R.sup.9).sub.2, Ge(R.sup.9).sub.2, Sn(R.sup.9).sub.2, C(R.sup.9).sub.2, C(R.sup.9).sub.2 --C(R.sup.9).sub.2, where R.sup.9 is C.sub.1 to C.sub.10 alkyl, C.sub.6 to C.sub.15 aryl or C.sub.3 to C.sub.10 cycloalkyl; and the ligand may have C.sub.S or C.sub.1 -symmetry. Preferred metals are selected from the group consisting of group III, group IV, group V or lanthanide group elements. The catalysts are used to prepare stereoregular polymers including polypropylene from .alpha.-olefin monomers.

  19. Clinical pharmacokinetics of the phosphate binder lanthanum carbonate.

    Science.gov (United States)

    Damment, Stephen J P; Pennick, Michael

    2008-01-01

    Lanthanum carbonate is considered to be the most potent of a new generation of noncalcium phosphate binders used to treat hyperphosphataemia in chronic kidney disease (CKD), a condition associated with progressive bone and cardiovascular pathology and a markedly elevated risk of death. Its phosphate-binding action involves ionic binding and precipitation of insoluble complexes within the lumen of the intestine, thereby preventing absorption of dietary phosphate. While pharmacokinetics have little relevance to the efficacy of lanthanum carbonate, they are of fundamental importance when it comes to evaluating safety. When administered as lanthanum carbonate, the oral bioavailability of lanthanum is low (approximately 0.001%). The small absorbed fraction is excreted predominantly in bile, with less than 2% being eliminated by the kidneys. Predictably, therefore, plasma exposure and pharmacokinetics have been shown to be similar in healthy human volunteers and CKD stage 5 patients. With almost complete plasma protein binding, free lanthanum concentrations in patients at steady state are carbonate has a low propensity to cause systemic drug interactions due to its poor absorption. However, the higher concentrations present in the gastrointestinal tract can form chelates with some drugs, such as fluoroquinolones, and reduce their absorption. The improved understanding of the pharmacokinetics of lanthanum that has emerged in recent years has helped to explain why the myriad of calcium-like effects described in vitro for lanthanum have little if any relevance in vivo. The pharmacokinetic investigations of lanthanum carbonate formed an important part of the stringent premarketing safety assessment process and have been influential in reassuring both regulators and physicians that the agent can be used safely and effectively in this vulnerable dialysis population.

  20. Effect of DNA groove binder distamycin A upon chromatin structure.

    Directory of Open Access Journals (Sweden)

    Parijat Majumder

    Full Text Available BACKGROUND: Distamycin A is a prototype minor groove binder, which binds to B-form DNA, preferentially at A/T rich sites. Extensive work in the past few decades has characterized the binding at the level of double stranded DNA. However, effect of the same on physiological DNA, i.e. DNA complexed in chromatin, has not been well studied. Here we elucidate from a structural perspective, the interaction of distamycin with soluble chromatin, isolated from Sprague-Dawley rat. METHODOLOGY/PRINCIPAL FINDINGS: Chromatin is a hierarchical assemblage of DNA and protein. Therefore, in order to characterize the interaction of the same with distamycin, we have classified the system into various levels, according to the requirements of the method adopted, and the information to be obtained. Isothermal titration calorimetry has been employed to characterize the binding at the levels of chromatin, chromatosome and chromosomal DNA. Thermodynamic parameters obtained thereof, identify enthalpy as the driving force for the association, with comparable binding affinity and free energy for chromatin and chromosomal DNA. Reaction enthalpies at different temperatures were utilized to evaluate the change in specific heat capacity (ΔCp, which, in turn, indicated a possible binding associated structural change. Ligand induced structural alterations have been monitored by two complementary methods--dynamic light scattering, and transmission electron microscopy. They indicate compaction of chromatin. Using transmission electron microscopy, we have visualized the effect of distamycin upon chromatin architecture at di- and trinucleosome levels. Our results elucidate the simultaneous involvement of linker bending and internucleosomal angle contraction in compaction process induced by distamycin. CONCLUSIONS/SIGNIFICANCE: We summarize here, for the first time, the thermodynamic parameters for the interaction of distamycin with soluble chromatin, and elucidate its effect on

  1. Mechanically controlled radical polymerization initiated by ultrasound

    Science.gov (United States)

    Mohapatra, Hemakesh; Kleiman, Maya; Esser-Kahn, Aaron Palmer

    2017-02-01

    In polymer chemistry, mechanical energy degrades polymeric chains. In contrast, in nature, mechanical energy is often used to create new polymers. This mechanically stimulated growth is a key component of the robustness of biological materials. A synthetic system in which mechanical force initiates polymerization will provide similar robustness in polymeric materials. Here we show a polymerization of acrylate monomers initiated and controlled by mechanical energy provided by ultrasonic agitation. The activator for an atom-transfer radical polymerization is generated using piezochemical reduction of a Cu(II) precursor complex, which thus converts a mechanical activation of piezoelectric particles to the synthesis of a new material. This polymerization reaction has some characteristics of controlled radical polymerization, such as narrow molecular-weight distribution and linear dependence of the polymeric chain length on the time of mechanical activation. This new method of controlled radical polymerization complements the existing methods to synthesize commercially useful well-defined polymers.

  2. Visible Light-Induced Metal Free Surface Initiated Atom Transfer Radical Polymerization of Methyl Methacrylate on SBA-15

    Directory of Open Access Journals (Sweden)

    Liang Ma

    2017-02-01

    Full Text Available Surface-initiated atom transfer radical polymerization (SI-ATRP is one of the most versatile techniques to modify the surface properties of materials. Recent developed metal-free SI-ATRP makes such techniques more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N-dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. A SBA-15-based polymeric composite with an adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous conditions. This procedure provides a low-cost, readily available, and easy modification method to synthesize polymeric composites without the contamination of metal.

  3. Problems in structural inorganic chemistry

    CERN Document Server

    Li, Wai-Kee; Mak, Thomas Chung Wai; Mak, Kendrew Kin Wah

    2013-01-01

    This book consists of over 300 problems (and their solutions) in structural inorganic chemistry at the senior undergraduate and beginning graduate level. The topics covered comprise Atomic and Molecular Electronic States, Atomic Orbitals, Hybrid Orbitals, Molecular Symmetry, Molecular Geometry and Bonding, Crystal Field Theory, Molecular Orbital Theory, Vibrational Spectroscopy, and Crystal Structure. The central theme running through these topics is symmetry, molecular or crystalline. The problems collected in this volume originate in examination papers and take-home assignments that have been part of the teaching of the book's two senior authors' at The Chinese University of Hong Kong over the past four decades. The authors' courses include Chemical Bonding, Elementary Quantum Chemistry, Advanced Inorganic Chemistry, X-Ray Crystallography, etc. The problems have been tested by generations of students taking these courses.

  4. Inorganic semiconductors for flexible electronics.

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Y.; Rogers, J. A.; Center for Nanoscale Materials; Univ. of Illinois

    2007-08-03

    This article reviews several classes of inorganic semiconductor materials that can be used to form high-performance thin-film transistors (TFTs) for large area, flexible electronics. Examples ranging from thin films of various forms of silicon to nanoparticles and nanowires of compound semiconductors are presented, with an emphasis on methods of depositing and integrating thin films of these materials into devices. Performance characteristics, including both electrical and mechanical behavior, for isolated transistors as well as circuits with various levels of complexity are reviewed. Collectively, the results suggest that flexible or printable inorganic materials may be attractive for a range of applications not only in flexible but also in large-area electronics, from existing devices such as flat-panel displays to more challenging (in terms of both cost and performance requirements) systems such as large area radiofrequency communication devices, structural health monitors, and conformal X-ray imagers.

  5. Evolution of microstructure and dimension of as-molded parts during thermal removal process of wax-based MIM binder

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The evolution of the microstructure and the dimension of as-molded parts were studied on the basis of the thermogravimetric analysis of wax-based MIM binder. The results show that the binder removal speeds are different in different temperature ranges during binder removal process. The evolution of the microstructure of as-molded parts during binder removal process clearly showed the initiation and formation of connected pore structure, which is the removal channel of the binder. The as-molded parts almost continuously shrank through binder removal process, except an expansion stage during 320~440  ℃, which is the dissolution expansion effect due to the dissolution of VPW in the polymer melt.

  6. The effect of crumb rubber particle size to the optimum binder content for open graded friction course.

    Science.gov (United States)

    Ibrahim, Mohd Rasdan; Katman, Herda Yati; Karim, Mohamed Rehan; Koting, Suhana; Mashaan, Nuha S

    2014-01-01

    The main objective of this paper is to investigate the relations of rubber size, rubber content, and binder content in determination of optimum binder content for open graded friction course (OGFC). Mix gradation type B as specified in Specification for Porous Asphalt produced by the Road Engineering Association of Malaysia (REAM) was used in this study. Marshall specimens were prepared with four different sizes of rubber, namely, 20 mesh size [0.841 mm], 40 mesh [0.42 mm], 80 mesh [0.177 mm], and 100 mesh [0.149 mm] with different concentrations of rubberised bitumen (4%, 8%, and 12%) and different percentages of binder content (4%-7%). The appropriate optimum binder content is then selected according to the results of the air voids, binder draindown, and abrasion loss test. Test results found that crumb rubber particle size can affect the optimum binder content for OGFC.

  7. [Use of the aluminum phosphate-binders in hemodialysis in the ultrapure water era].

    Science.gov (United States)

    Arenas, Maria D; Malek, T; Gil, M T; Moledous, A; Núñez, C; Alvarez-Ude, F

    2008-01-01

    Aluminium binder has been ill-advised, but his use remain applicable in the clinique practice in very seleccionated and particular patients. The repercussion of prolonged treatment with low doses of aluminium phosphate-binders in haemodialysis was studied. The haemodialysis unit had a double osmosis inverse and the aluminium levels in haemodialysis liquid was less than 2 micrograms/liter. 41 patients of the 295 on haemodialysis received aluminium phosphate-binders since the 2005 January to the 2007 November. The mean time of treatment was 17.8 months, and the doses was 3.9 tablets day (mean of 463 grams in the studied period). The association of low doses of aluminium phosphate-binders permitted a better control of phosphorus (6.8 to 4.8 mg/dl; p<0.0001), with a reduction of the others phosphate-binders: sevelamer (10.4 a 8 tablets/day; p<0.0001) and calcium phosphate-binders (4.6 to 3.1 tablets/day; p<0.0001). The serum aluminium increased after the aluminium treatment (6.8 to 13.8 mcg/l; p<0.0001), and no toxicity indirect signs were observed on CMV, haemoglobin, none PTH. Five patients (12.1%) reached aluminium serum levels higher 20 mcg/l, and none reached the 40 mcg/l. The aluminium phosphate-binders were effective, economical and, now, with an apparent better security profile than in a previous time, but it is very important to be careful with this use and to follow a vigilance strict on patients and haemodialysis liquid.

  8. Ionic Liquids and Poly(ionic liquid)s for Morphosynthesis of Inorganic Materials.

    Science.gov (United States)

    Gao, Min-Rui; Yuan, Jiayin; Antonietti, Markus

    2016-10-06

    Ionic liquids (ILs) are new, innovative ionic solvents with rich physicochemical properties and intriguing pre-organized solvent structures; these materials offer great potential to impact across versatile areas of scientific research, for example, synthetic inorganic chemistry. Recent use of ILs as precursors, templates, and solvents has led to inorganic materials with tailored sizes, dimensionalities, morphologies, and functionalities that are difficult to obtain, or even not accessible, by using conventional solvents. Poly(ionic liquid)s (PILs) polymerized from IL monomers also raise the prospect of modifying nucleation, growth, and crystallization of inorganic objects, shedding light on the synthesis of a wide range of new materials. Here we survey recent key progress in using ILs and PILs in the field of synthetic inorganic chemistry. As well as highlighting the unique features of ILs and PILs that enable advanced synthesis, the effects of adding other solvents to the final products, along with the emerging applications of the created inorganic materials will be discussed. We finally provide an outlook on several development opportunities that could lead to new advancements of this exciting research field.

  9. Comparison of the activities of binder-added and binder-free Mo/HZSM-5 catalysts in methane dehydroaromatization at 1073 K in periodic CH4-H2 switch operation mode

    Institute of Scientific and Technical Information of China (English)

    Yuebing Xu; Hongtao Ma; Yo Yamamoto; Yoshizo Suzuki; Zhanguo Zhang

    2012-01-01

    Three industry-supplied,well-shaped Mo/HZSM-5 catalysts,two binder-added and one binder-free,were tested for the first time in methane dehydroaromatization to benzene at 1073 K and 10000 mL/(g.h) in periodic CH4-H2 switch operation mode,and their catalytic performances were compared with those of three self-prepared,binder-free powder Mo/HZSM-5 catalysts.XRD,27Al NMR,SEM,BET and NH3-TPD characterizations of all the catalysts show that the zeolites in the two binder-added catalysts are comparable to those in the three binder-free powder catalysts in crystallinity,crystal size,micropore volume and Br(¢)nsted acidity.The test results,on the other hand,show that the catalytic performances of the two binder-added catalysts are worse than those of the four binder-free catalysts on both catalyst mass and zeolite mass bases.Then,TPO and BET measurements of all spent samples were conducted to get a deep insight into the negative effects of binder addition,and the results suggest that the binder additives functioned mainly to enhance the polyaromatization of formed aromatics to coke on their external surfaces and consequently lower the benzene formation activity and selectivity of the catalyst.

  10. Supramolecular Polymeric Materials Containing Cyclodextrins.

    Science.gov (United States)

    Nakahata, Masaki; Takashima, Yoshinori; Harada, Akira

    2017-01-01

    Smart design of polymeric materials may lead to intelligent materials exhibiting unique functional properties. Looking at nature, living systems use specific and reversible intermolecular interactions in realizing complex functions. Hence reversible bonds based on selective molecular recognition can impart artificial materials with unique functional properties. This review mainly focuses on supramolecular polymeric materials based on cyclodextrin-based host-guest interactions. Polymeric materials using molecular recognition at polymer main chain, side chain, and termini are described. Polymers carrying host and guest residues exhibit unique properties such as: 1) formation of macroscopic self-assembly of polymer gels carrying host and guest residues; 2) stimuli-responsive self-healing properties due to the reversible nature of host-guest interactions; and 3) macroscopic motion of artificial muscle cross-linked by host-guest interaction controlled by external stimuli. An overview of recent developments in this new frontier between materials science and life science is given.

  11. Influence of fluoropolymer binders on the electrochemical performance of C-LiFePO4 based cathodes

    OpenAIRE

    A. Goren; Costa, C M; Silva, Maria Manuela; Lanceros-Méndez, S.

    2016-01-01

    The polymer binder plays a relevant role in the performance of battery electrodes. This work proposes poly(vinylidene fluoride-co-trifluoroethylene), PVDF-TrFE, as a polymer binder for C-LiFePO4 based cathodes and investigates its effect in the electrochemical properties of the cathodes. Morphological, electrical, swelling and electrochemical properties were investigated for this polymer binder and the results were compared with the ones from two other fluoropolymers, poly(v...

  12. Surface glycosylation of polymeric membranes

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Surface glycosylation of polymeric membranes has been inspired by the structure of natural biomem-branes. It refers to that glycosyl groups are introduced onto the membrane surface by various strate-gies, which combine the separation function of the membrane with the biological function of the sac-charides in one system. In this review, progress in the surface glycosylation of polymeric membranes is highlighted in two aspects, i.e. the glycosylation methods and the potential applications of the sur-face-glycosylated membranes.

  13. On-demand photoinitiated polymerization

    Science.gov (United States)

    Boydston, Andrew J; Grubbs, Robert H; Daeffler, Chris; Momcilovic, Nebojsa

    2013-12-10

    Compositions and methods for adjustable lenses are provided. In some embodiments, the lenses contain a lens matrix material, a masking compound, and a prepolymer. The lens matrix material provides structure to the lens. The masking compound is capable of blocking polymerization or crosslinking of the prepolymer, until photoisomerization of the compound is triggered, and the compound is converted from a first isomer to a second isomer having a different absorption profile. The prepolymer is a composition that can undergo a polymerization or crosslinking reaction upon photoinitiation to alter one or more of the properties of the lenses.

  14. Inorganic treatments for the consolidation and protection of stone artefacts

    Directory of Open Access Journals (Sweden)

    Mauro Matteini

    2008-04-01

    Full Text Available Consolidation and protection are two of the principal kinds of treatments through which the decay of old statues, stone facades, plasters and mural paintings caused by both natural atmospheric agents and, above all in the last five decades, by atmospheric pollution, is faced. The most traditional approach has been and is mainly based on the use of organic polymeric materials. They offer the advantage of easy application procedures and the possibility to obtain, at short times, very satisfying results. Different is their behaviour at long times. Some drawbacks come out over time both under the esthetical point of view as well as to the durability, compatibility and efficacy. Particularly critical is the situation when porous materials and soluble salts - gypsum above all - are simultaneously present. In such a situation inorganic treatments demonstrate to be much more appropriate. They assure durable and compatible results. In the present paper two of the most efficient and appropriate inorganic methods are reviewed in detail: the barium hydroxide method, both as desulfating and consolidating agent, and the ammonium oxalate method as passivating agent, consolidant and as a treatment capable of improving the natural colour contrast of the stone, when it is lost due to decay processes.

  15. Heat treatment of medium-temperature Sasol-Lurgi gasifier coal-tar pitch for polymerizing to higher value products

    Energy Technology Data Exchange (ETDEWEB)

    K. Mokoena; T.J. Van der Walt; T.J. Morgan; A.A. Herod; R. Kandiyoti [Sasol Technology (Pty) Ltd., Sasolburg (South Africa). R& amp; D Division

    2008-05-15

    Two coal-derived pitch samples, one a medium temperature pitch from a Sasol-Lurgi gasifier and the other from a high temperature coking process, have been heat treated to induce polymerization, both separately and as a mixture of pitches (co-pyrolysis). The initial pitch samples and the heat-treated samples have been examined by size exclusion chromatography (SEC) in 1-methyl-2-pyrrolidinone (NMP), by UV-fluorescence spectroscopy (UV-F), by solid state {sup 13}C NMR; elemental analyses of the initial pitch samples have been carried out. The Sasol-Lurgi pitch showed larger apparent sizes, more alkyl and carbonyl functions, and smaller polycyclic aromatic hydrocarbon (PAH) groups than the high temperature pitch. Co-pyrolysis of the two pitches indicated that polymerized product from the Sasol-Lurgi pitch can be used as an extender for high-temperature binder pitch. 16 refs., 7 figs., 2 tabs.

  16. Evaluation of strength-enhancing factors of a ductile binder in direct compression of sodium bicarbonate and calcium carbonate powders.

    Science.gov (United States)

    Mattsson, S; Nyström, C

    2000-03-01

    This study evaluated the effectiveness of a ductile binder in direct compression of sodium bicarbonate and calcium carbonate powders. Properties associated with both the binder and the compound were studied. The addition of binder materials, such as polyethylene glycols (PEGs) of differing molecular weights or microcrystalline cellulose, generally resulted in an increase in the axial tensile strength of the corresponding compacts. The increase in tablet strength was generally greater with the PEGs than with microcrystalline cellulose. The results indicate that the improvement in tablet strength caused by the binder is dependent on properties of both the binder and the compound. By utilising different methods it was established that the fracture during tablet strength testing mainly occurred around the compound particles. As a consequence of this, it appears that the ability of the binder to fill the voids between the compound particles is a determinative factor for increasing tablet strength. The binder appeared to have less effect when added to compounds that fragmented during compaction. Characteristics of the binder resulting in the greatest decrease in porosity, and thus the greatest increase in the tensile strength of the compound, included a high degree of plastic deformation with a limited elastic component and a small particle size. Obviously, the amount of binder added to the mixture also affected the results.

  17. Adhesive Bonding and Self-Curing Characteristics of α-Starch Based Composite Binder for Green Sand Mould/Core

    Institute of Scientific and Technical Information of China (English)

    Xia ZHOU; Jinzong YANG; Guohui QU

    2004-01-01

    Interactions between different components in α-starch based composite binder for green sand mould/core were investigated by using XRD, IR spectra, 1H NMR spectra and SEM. Several adhesive hardening structures and theories of the binder at room temperature were proposed according to the interactions between various compositions. Thus,the reasons for the binder to have excellent combination properties and unique adhesive bonding and self-curing characteristics were explained by these theories successfully. And the theories are of great directive importance to design and development of composite binder for green sand mould/core.

  18. Emission of organic compounds from mould and core binders used for casting iron, aluminium and bronze in sand moulds.

    Science.gov (United States)

    Tiedje, Niels; Crepaz, Rudolf; Eggert, Torben; Bey, Niki

    2010-12-01

    Emissions from mould and core sand binders commonly used in the foundry industry have been investigated. Degradation of three different types of binders was investigated: Furfuryl alcohol (FA), phenolic urethane (PU) and resol-CO2 (RC). In each group of binders, at least two different binder compositions were tested. A test method that provides uniform test conditions is described. The method can be used as a general test method to analyse off gases from binders. Moulds, containing a standard size casting, were produced and the amount and type of organic compounds, resulting from thermal degradation of binders, was monitored when cast iron, bronze and aluminium was poured in the moulds. Binder degradation was measured by collecting off gases in a specially designed ventilation hood at a constant flow rate. Samples were taken from the ventilation system and analysed for hydrocarbons and CO content. It is shown how off-gases vary with time after pouring and shake out. Also the composition of off-gases is analysed and shown. It is further shown how the composition of off-gasses varies between different types of binders and with varying composition of the binders as well as function of the thermal load on the moulding sand.

  19. Strength loss in MA-MOX green pellets from radiation damage to binders

    Science.gov (United States)

    Lessing, Paul A.; Cannon, W. Roger; Egeland, Gerald W.; Zuck, Larry D.; Jewell, James K.; Akers, Douglas W.; Groenewold, Gary S.

    2013-06-01

    The fracture strength of green Minor Actinides (MA)-MOX pellets containing 75 wt.% DUO2, 20 wt.% PuO2, 3 wt.% AmO2 and 2 wt.% NpO2 was studied as a function of storage time, after mixing with the binder and before sintering, to test the effect of radiation damage on binders. Fracture strength degraded continuously over the 10 days of the study for all three binders studied: PEG binder (Carbowax 8000), microcrystalline wax (Mobilcer X) and styrene-acrylic copolymer (Duramax B1022) but the fracture strength of Duramax B1022 degraded the least. For instance, for several hours after mixing Carbowax 8000 with MA-MOX, the fracture strength of a pellet was reasonably high and pellets were easily handled without breaking but the pellets were too weak to handle after 10 days. Strength measured using diametral compression test showed that strength degradation was more rapid in pellets containing 1.0 wt.% Carbowax PEG 8000 compared to those containing only 0.2 wt.%, suggesting that irradiation not only left the binder less effective but also reduced the pellet strength. In contrast the strength of pellets containing Duramax B1022 degraded very little over the 10 days period. It was suggested that the styrene portion present in the Duramax B1022 copolymer provided the radiation resistance.

  20. Strength Loss in MA-MOX Green Pellets from Radiation Damage to Binders

    Energy Technology Data Exchange (ETDEWEB)

    Paul A. Lessing; W.R. Cannon; Gerald W. Egeland; Larry D. Zuck; James K. Jewell; Douglas W. Akers; Gary S. Groenewold

    2013-06-01

    The fracture strength of green Minor Actinides (MA)-MOX pellets containing 75 wt.% DUO2, 20 wt. % PuO2, 3 wt. % AmO2 and 2 wt. % NpO2 was studied as a function of storage time, after mixing in the binder and before sintering, to test the effect of radiation damage on binders. Fracture strength degraded continuously over the 10 days of the study for all three binders studied: PEG binder (Carbowax 8000), microcrystalline wax (Mobilcer X) and Styrene-acrylic copolymer (Duramax B1022) but the fracture strength of Duramax B1022 degraded the least. For instance, for several hours after mixing Carbowax 8000 with MA MOX, the fracture strength of a pellet was reasonably high and pellets were easily handled without breaking but the pellets were too weak to handle after 10 days. Strength measured using diametral compression test showed strength degradation was more rapid in pellets containing 1.0 wt. % Carbowax PEG 8000 compared to those containing only 0.2 wt. %, suggesting that irradiation not only left the binder less effective but also reduced the pellet strength. In contrast the strength of pellets containing Duramax B1022 degraded very little over the 10 day period. It was suggested that the styrene portion of the Duramax B1022 copolymer provided the radiation resistance.

  1. Strength loss in MA-MOX green pellets from radiation damage to binders

    Energy Technology Data Exchange (ETDEWEB)

    Lessing, Paul A. [Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Cannon, W. Roger, E-mail: wrogercannon@gmail.com [Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Egeland, Gerald W.; Zuck, Larry D.; Jewell, James K.; Akers, Douglas W.; Groenewold, Gary S. [Idaho National Laboratory, Idaho Falls, ID 83415 (United States)

    2013-06-15

    The fracture strength of green Minor Actinides (MA)-MOX pellets containing 75 wt.% DUO{sub 2}, 20 wt.% PuO{sub 2}, 3 wt.% AmO{sub 2} and 2 wt.% NpO{sub 2} was studied as a function of storage time, after mixing with the binder and before sintering, to test the effect of radiation damage on binders. Fracture strength degraded continuously over the 10 days of the study for all three binders studied: PEG binder (Carbowax 8000), microcrystalline wax (Mobilcer X) and styrene–acrylic copolymer (Duramax B1022) but the fracture strength of Duramax B1022 degraded the least. For instance, for several hours after mixing Carbowax 8000 with MA-MOX, the fracture strength of a pellet was reasonably high and pellets were easily handled without breaking but the pellets were too weak to handle after 10 days. Strength measured using diametral compression test showed that strength degradation was more rapid in pellets containing 1.0 wt.% Carbowax PEG 8000 compared to those containing only 0.2 wt.%, suggesting that irradiation not only left the binder less effective but also reduced the pellet strength. In contrast the strength of pellets containing Duramax B1022 degraded very little over the 10 days period. It was suggested that the styrene portion present in the Duramax B1022 copolymer provided the radiation resistance.

  2. Evaluation of the rheological behavior of asphaltic binder modified with zeolite material

    Energy Technology Data Exchange (ETDEWEB)

    Silveira, E.M. da; Sant' ana, Hosiberto B.; Soares, Sandra A.; Soares, Jorge B. [Federal University of Ceara, Fortaleza, CE (Brazil)

    2008-07-01

    Several new processes have been developed to reduce mixing and compaction temperatures of hot mix asphalt without sacrificing the quality of the resulting pavement. One of these processes utilizes the zeolite, a crystalline hydrated aluminum silicate. A laboratory study was conducted to determine the applicability of zeolite to improve the rheological and chemical behavior of an asphaltic binder. The synthetic asphaltic binder was produced with different zeolite contents (0,1; 0.3; and 0.5% w/w) by wet process. The rheological and chemical behavior was verified by Dynamic Shear Rheometer and Infrared Spectroscopy, respectively. The zeolite's chemical composition and morphology was studied by Dispersive X-ray Spectroscopy (EDX). Additionally, the scanning electron microscope (SEM) was utilized to establish the zeolite elemental composition. The results showed that investigated zeolite was classified as a sodium aluminum silicate and it was able to modify the rheological properties of the neat asphalt binder. The G*/sin{delta} parameter was affected by the zeolite presence, indicating better performance for the binders with zeolite. The results show that synthetic binders can partly replicate the rheological properties of conventional AB. Comparable complex modulus values was obtained. No significant difference was found in viscoelastic response, given by the phase angles as a function of both temperature and frequency. (author)

  3. Physical and Combustion Characteristics of Briquettes Made from Water Hyacinth and Phytoplankton Scum as Binder

    Directory of Open Access Journals (Sweden)

    R. M. Davies

    2013-01-01

    Full Text Available The study investigated the potential of water hyacinths and phytoplankton scum, an aquatic weed, as binder for production of fuel briquettes. It also evaluated some physical and combustion characteristics. The water hyacinths were manually harvested, cleaned, sun-dried, and milled to particle sizes distribution ranging from <0.25 to 4.75 mm using hammer mill. The water hyacinth grinds and binder (phytoplankton scum at 10% (B1, 20% (B2, 30% (B3, 40% (B4, and 50% (B5 by weight of each feedstock were fed into a steel cylindrical die of dimension 14.3 cm height and 4.7 cm diameter and compressed by hydraulic press at pressure 20 MPa with dwell time of 45 seconds. Data were analysed using analysis of variance and descriptive statistics. Initial bulk density of uncompressed mixture of water hyacinth and phytoplankton scum at different binder levels varied between 113.86 ± 3.75 (B1 and 156.93 ± 4.82 kg/m3 (B5. Compressed and relaxed densities of water hyacinth briquettes at different binder proportions showed significant difference . Durability of the briquettes improved with increased binder proportion. Phytoplankton scum improved the mechanical handling characteristics of the briquettes. It could be concluded that production of water hyacinth briquettes is feasible, cheaper, and environmentally friendly and that they compete favourably with other agricultural products.

  4. Influence of Cellulosic Binders on Sensitivity and Combustion Behaviour of B-KNO3 Ignition System

    Directory of Open Access Journals (Sweden)

    Varsha Bhingarkar

    2006-07-01

    Full Text Available Boron-potassium nitrate (B-KNO3-based compositions have been used as an effective ignitersystem for solid rocket propellants. A systematic study was undertaken to generate exhaustivedata on B-KNO3 (25:65-based ignition systems with cellulosic binders, viz., nitrocellulose, ethylcellulose and plasticised ethyl cellulose. In addition, detailed investigations were carried outwith PEC as binder by varying its concentration from 2-10 per cent in the same system. Theexperimental compositions (B-KNO3: binder were evaluated by closed-vessel firing, thermalanalysis, sensitivity, mechanical properties and cal-val determination. The binders significantlyinfluenced the sensitivity and combustion behaviour of B-KNO3 compositions. The compositionwith nitrocellulose as binder produced high flame temperature and cal-val as compared to ethylcellulose and plasticised ethyl cellulose-based compositions. The data indicated that thecalculated flame temperature for all compositions was in the range 2716 K to 2957 K. As theplasticised ethyl cellulose content increased from 2 per cent to 10 per cent, the maximum pressureincreased with decrease in heat of combustion.

  5. Rheological and thermal performance of newly developed binder systems for ceramic injection molding

    Science.gov (United States)

    Hausnerova, Berenika; Kasparkova, Vera; Hnatkova, Eva

    2016-05-01

    In a novel binder system, carnauba wax was considered to replace the synthetic backbone polymers (polyolefins) enhancing the environmental sustainability of Ceramic Injection Molding (CIM) technology. The paper presents comparison of the rheological performance and thermal behavior of the aluminum oxide CIM feedstocks based on a binder containing carnauba wax with those consisting of a commercial binder. Further, acrawax (N, N'-Ethylene Bis-stearamide) has been considered as another possible substitute of polyolefins. For both proposed substitutes there is a significant reduction in viscosity, and in case of carnauba wax based feedstock also in processing temperature, which is essential for injection molding of reactive powders. Thermal characterization comprised analyses of single neat binders, their mixtures and mixtures with aluminum oxide. The presence of powder lowered melting temperatures of all tested binders except of polyolefin. Further depression in melting point of poly(ethylene glycol) is observed in combination with polyolefin in the presence of powder, and it is related to changes in size of the crystalline domains.

  6. Influence of binder droplet dimension on granulation rate during fluidized bed granulation.

    Science.gov (United States)

    Fujiwara, Maya; Dohi, Masafumi; Otsuka, Tomoko; Yamashita, Kazunari; Sako, Kazuhiro

    2013-01-01

    Here, we statistically identified the critical factor of the granulation rate during the fluidized bed granulation process. Lactose was selected as the excipient and was granulated with several binders, including hydroxypropyl cellulose, hydroxypropyl methyl cellulose, and polyvinylpyrrolidone. The viscosity, density, and surface tension of the binder solution, contact angle, and the work done during adhesion and cohesion between the binder and lactose, mist diameter, Stokes number, and the dimension of the droplet were considered. The Stokes number was defined as the ratio of the inertial force to the viscous-damping force of a particle. We confirmed that droplet diameter after adhesion had the highest correlation coefficient with the granulation rate constant in our investigated parameters. Partial least squares regression revealed two critical principal components of the granulation rate: one relating to the droplet dimension, which is composed of mist diameter and diameter and thickness of the droplet after adhesion of the binder to the lactose surface; and the other relating to wettability, which involves the work done during adhesion and cohesion, surface tension, and the thickness of the droplet after adhesion of the binder to the lactose surface.

  7. Influence of solidification accelerators on structure formation of anhydrite-containing binders

    Energy Technology Data Exchange (ETDEWEB)

    Anikanova, L., E-mail: alasmit@mail.ru; Volkova, O., E-mail: v.olga.nikitina@gmail.com; Kudyakov, A.; Sarkisov, Y.; Tolstov, D. [Tomsk State University of Architecture and Building, 2 Solyanaya sq., Tomsk, 634003 (Russian Federation)

    2016-01-15

    The article presents results of scientific analysis of chemical additives influence on acid fluoride binder. It was found that the influence of sulfate nature additives on the process of hydration and solidification of the binder is similar to influence of additives on indissoluble anhydrite. Additives with SO{sub 4}{sup 2−} anion NO{sup −} are more efficient. The mentioned additives according to accelerating effect belong to the following succession: K{sub 2}SO{sub 4} > Na{sub 2}SO{sub 4} > FeSO{sub 4} > MgSO{sub 4}. Facilitation of the process of hydration and solidification of the binder, increase in density and durability of the binder (32 MPa) is to the greatest extent achieved with the introduction of 2% sodium sulfate additive of the binder’s mass into the composition of the binder along with the ultrasonic treatment of water solution. Directed crystal formation process with healing of porous structure by new growths presented as calcium sulfate dehydrate and hydroglauberite provides positive effect.

  8. Control of binder viscosity and hygroscopicity on particle aggregation efficiency

    Science.gov (United States)

    Mueller, Sebastian B.; Kueppers, Ulrich; Ayris, Paul M.; Jacob, Michael; Delmelle, Pierre; Dingwell, Donald B.

    2016-04-01

    In the course of explosive volcanic eruptions, large amounts of ash are released into the atmosphere and may subsequently pose a threat to infrastructure, such as aviation industry. Ash plume forecasting is therefore a crucial tool for volcanic hazard mitigation but may be significantly affected by aggregation, altering the aerodynamic properties of particles. Models struggle with the implementation of aggregation since external conditions promoting aggregation have not been completely understood; in a previous study we have shown the rapid generation of ash aggregates through liquid bonding via the use of fluidization bed technology and further defined humidity and temperature ranges necessary to trigger aggregation. Salt (NaCl) was required for the recovery of stable aggregates, acting as a cementation agent and granting aggregate cohesion. A numerical model was used to explain the physics behind particle aggregation mechanisms and further predicted a dependency of aggregation efficiency on liquid binder viscosity. In this study we proof the effect of viscosity on particle aggregation. HCl and H2SO4 solutions were diluted to various concentrations resulting in viscosities between 1 and 2 mPas. Phonolitic and rhyolitic ash samples as well as soda-lime glass beads (serving as analogue material) were fluidized in the ProCell Lab® of Glatt Ingenieurtechnik GmbH and treated with the acids via a bottom-spray technique. Chemically driven interaction between acid liquids and surfaces of the three used materials led to crystal precipitation. Salt crystals (e.g. NaCl) have been confirmed through scanning electron microscopy (SEM) and leachate analysis. Both volcanic ash samples as well as the glass beads showed a clear dependency of aggregation efficiency on viscosity of the sprayed HCl solution. Spraying H2SO4 provoked a collapse of the fluidized bed and no aggregation has been observed. This is accounted by the high hygroscopicity of H2SO4. Dissolving CaCl2 (known to be

  9. Functionalization and Polymerization on the CNT Surfaces

    KAUST Repository

    Albuerne, Julio

    2013-07-01

    In this review we focus on the current status of using carbon nanotube (CNT) as a filler for polymer nanocomposites. Starting with the historical background of CNT, its distinct properties and the surface functionalization of the nanotube, the three different surface polymerization techniques, namely grafting "from", "to" and "through/in between" were discussed. Wider focus has been given on "grafting from" surface initiated polymerizations, including atom transfer radical polymerization (ATRP), reversible addition fragmentation chain-transfer (RAFT) Polymerization, nitroxide mediated polymerization (NMP), ring opening polymerization (ROP) and other miscellaneous polymerization methods. The grafting "to" and "through / in between" also discussed and compared with grafting from polymerization. The merits and shortcomings of all three grafting methods were discussed and the bottleneck issue in grafting from method has been highlighted. Furthermore the current and potential future industrial applications were deliberated. Finally the toxicity issue of CNTs in the final product has been reviewed with the limited available literature knowledge. © 2013 Bentham Science Publishers.

  10. The Viscosity of Polymeric Fluids.

    Science.gov (United States)

    Perrin, J. E.; Martin, G. C.

    1983-01-01

    To illustrate the behavior of polymeric fluids and in what respects they differ from Newtonian liquids, an experiment was developed to account for the shear-rate dependence of non-Newtonian fluids. Background information, procedures, and results are provided for the experiment. Useful in transport processes, fluid mechanics, or physical chemistry…

  11. Biodegradable polymeric prodrugs of naltrexone

    NARCIS (Netherlands)

    Bennet, D.B.; Li, X.; Adams, N.W.; Kim, S.W.; Hoes, C.J.T.; Feijen, J.

    1991-01-01

    The development of a biodegradable polymeric drug delivery system for the narcotic antagonist naltrexone may improve patient compliance in the treatment of opiate addiction. Random copolymers consisting of the ¿-amino acids N5-(3-hydroxypropyl--glutamine and -leucine were synthesized with equimolar

  12. Buckling of polymerized monomolecular films

    Science.gov (United States)

    Bourdieu, L.; Daillant, J.; Chatenay, D.; Braslau, A.; Colson, D.

    1994-03-01

    The buckling of a two-dimensional polymer network at the air-water interface has been evidenced by grazing incidence x-ray scattering. A comprehensive description of the inhomogeneous octadecyltrichlorosilane polymerized film was obtained by atomic force microscopy and x-ray scattering measurements. The buckling occurs with a characteristic wavelength ~=10 μm.

  13. Novel polymeric materials from triglycerides

    Science.gov (United States)

    Triglycerides are good platforms for new polymeric products that can substitute for petroleum-based materials. As part of our research emphasis in sustainability and green polymer chemistry, we have explored a number of reactions in efforts to produce a wide range of value-added products. In this ...

  14. Fullerene thin-film transistors fabricated on polymeric gate dielectric

    Energy Technology Data Exchange (ETDEWEB)

    Puigdollers, J. [Micro and Nano Technology Group (MNT), Dept. Enginyeria Electronica, Universitat Politecnica Catalunya, C/ Jordi Girona 1-3, Modul C4, 08034-Barcelona (Spain)], E-mail: jpuigd@eel.upc.edu; Voz, C. [Micro and Nano Technology Group (MNT), Dept. Enginyeria Electronica, Universitat Politecnica Catalunya, C/ Jordi Girona 1-3, Modul C4, 08034-Barcelona (Spain); Cheylan, S. [ICFO - Mediterranean Technology Park, Avda del Canal Olimpic s/n, 08860-Castelldefels (Spain); Orpella, A.; Vetter, M.; Alcubilla, R. [Micro and Nano Technology Group (MNT), Dept. Enginyeria Electronica, Universitat Politecnica Catalunya, C/ Jordi Girona 1-3, Modul C4, 08034-Barcelona (Spain)

    2007-07-16

    Thin-film transistors with fullerene as n-type organic semiconductor have been fabricated. A polymeric gate dielectric, polymethyl methacrylate, has been used as an alternative to usual inorganic dielectrics. No significant differences in the microstructure of fullerene thin-films grown on polymethyl methacrylate were observed. Devices with either gold or aluminium top electrodes have been fabricated. Although the lower work-function of aluminium compared to gold should favour electron injection, similar field-effect mobilities in the range of 10{sup -2} cm{sup 2} V{sup -1} s{sup -1} were achieved in both cases. Actually, the output characteristics indicate that organic thin-film transistors behave more linearly with gold than with aluminium electrodes. These results confirm that not only energy barriers determine carrier injection at metal/organic interfaces, but also chemical interactions.

  15. A Route Towards Sustainability Through Engineered Polymeric Interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Reeja-Jayan, B; Kovacik, P; Yang, R; Sojoudi, H; Ugur, A; Kim, DH; Petruczok, CD; Wang, XX; Liu, AD; Gleason, KK

    2014-05-30

    Chemical vapor deposition (CVD) of polymer films represent the marriage of two of the most important technological innovations of the modern age. CVD as a mature technology for growing inorganic thin films is already a workhorse technology of the microfabrication industry and easily scalable from bench to plant. The low cost, mechanical flexibility, and varied functionality offered by polymer thin films make them attractive for both macro and micro scale applications. This review article focuses on two energy and resource efficient CVD polymerization methods, initiated Chemical Vapor Deposition (iCVD) and oxidative Chemical Vapor Deposition (oCVD). These solvent-free, substrate independent techniques engineer multi-scale, multi-functional and conformal polymer thin film surfaces and interfaces for applications that can address the main sustainability challenges faced by the world today.

  16. Polymeric amines and biomedical uses thereof

    NARCIS (Netherlands)

    Broekhuis, Antonius; Zhang, Youchum; Picchioni, Francesco; Roks, Antonius

    2010-01-01

    The invention relates to the field of polymers and biomedical applications thereof. In particular, it relates to the use of polymeric amines derived from alternating polyketones.Provided is the use of a polymeric amine for modulating or supporting cellular behavior, said polymeric amine being an alt

  17. THE POLYMERIZATION OF AROMATIC AND HETEROCYCLIC DINITRILES

    Institute of Scientific and Technical Information of China (English)

    HUANG Zhitang

    1988-01-01

    This review is a concise survey about the works in our laboratory on the polymerization of aromatic and heterocyclic dinitriles, including the polymerization kinetics and mechanism, synthesis of heterocyclic dinitriles, the structure of polymers, and the correlation between the structures of dinitriles and polymerization rates and thermal performances of polymers.

  18. Glycine Polymerization on Oxide Minerals

    Science.gov (United States)

    Kitadai, Norio; Oonishi, Hiroyuki; Umemoto, Koichiro; Usui, Tomohiro; Fukushi, Keisuke; Nakashima, Satoru

    2016-07-01

    It has long been suggested that mineral surfaces played an important role in peptide bond formation on the primitive Earth. However, it remains unclear which mineral species was key to the prebiotic processes. This is because great discrepancies exist among the reported catalytic efficiencies of minerals for amino acid polymerizations, owing to mutually different experimental conditions. This study examined polymerization of glycine (Gly) on nine oxide minerals (amorphous silica, quartz, α-alumina and γ-alumina, anatase, rutile, hematite, magnetite, and forsterite) using identical preparation, heating, and analytical procedures. Results showed that a rutile surface is the most effective site for Gly polymerization in terms of both amounts and lengths of Gly polymers synthesized. The catalytic efficiency decreased as rutile > anatase > γ-alumina > forsterite > α- alumina > magnetite > hematite > quartz > amorphous silica. Based on reported molecular-level information for adsorption of Gly on these minerals, polymerization activation was inferred to have arisen from deprotonation of the NH3 + group of adsorbed Gly to the nucleophilic NH2 group, and from withdrawal of electron density from the carboxyl carbon to the surface metal ions. The orientation of adsorbed Gly on minerals is also a factor influencing the Gly reactivity. The examination of Gly-mineral interactions under identical experimental conditions has enabled the direct comparison of various minerals' catalytic efficiencies and has made discussion of polymerization mechanisms and their relative influences possible Further systematic investigations using the approach reported herein (which are expected to be fruitful) combined with future microscopic surface analyses will elucidate the role of minerals in the process of abiotic peptide bond formation.

  19. Effect of Tar-resin Binder on Properties of MgO-C Monolithic Refractories

    Institute of Scientific and Technical Information of China (English)

    Hady EFENDY; Wan Mohd.Farid BIN WAN MOHAMAD

    2010-01-01

    Based on the newly developed bonding system,a new generation of carbon-bonded MgO-C monolithic refractories product with low toxic potential has been developed.Results of an on-going investigation on properties of MgO-C monolithic refractories with tar-resin as binder are presented.Furthermore,the binder is an extremely strong carbon bonding.Further significant advantages of this system are high oxidation resistance of the highly-ordered carbon structure and the excellent stress-absorbing structure.To improve the strength and erosion resistance,and to decrease evaporation during heating,a preliminary treated tar-resin with higher melting temperature and lower content of volatile component was investigated.The binder specimens were treated at 800 ℃ and the mechanical properties of MgO-C refractories specimens treated at 200,400,and 1 200 ℃ were determined.

  20. The role of the binder phase in the WC-Co sintering

    Directory of Open Access Journals (Sweden)

    Silva A.G.P. da

    2001-01-01

    Full Text Available The sintering of hardmetal in the solid state is studied. The influence of the WC particle size on the sintering kinetics, the role of the binder phase in the densification process and how sintering depends on the heating conditions are investigated. It is observed that alloys with different WC particle size show quite different structural evolution during sintering, although the densification mechanisms are the same. This is explained by the formation of agglomerates of WC and Co. Hardmetal alloys can sinter very rapidly when high heating rates are used, since rapid heating accelerates the binder spreading and the formation of WC-Co agglomerates. The binder phase (Co spreads on the WC particles initially as a thin layer. Subsequently, more Co spreads on this layer and WC-Co agglomerates are formed.

  1. STRUCTURE AND PROPERTIES OF COMPOSITE MATERIAL BASED ON GYPSUM BINDER AND CARBON NANOTUBES

    Directory of Open Access Journals (Sweden)

    CHUMAK Anastasia Gennadievna

    2013-04-01

    Full Text Available The aim of this work is to carry out a number of studies in the area of nanomodi­fication of gypsum binder matrix and to investigate the influence of multilayer carbon nanotubes on the structure, physical and mechanical properties of obtained compos­ites. The study of the gypsum binders structure formation mechanisms with the use of nanoadditives makes it possible to control the production processes of gypsum materi­als and articles with the given set of properties. The main tasks of the binder nanomodification are: even distribution of carbon nanostructures over the whole volume of material and provision of stability for the nanodimensional modifier during production process of the construction composite.

  2. Springback Control With Variable Binder Force — Experiments And FEA Simulation

    Science.gov (United States)

    Du, Changqing; Wu, Jin; Militisky, Marcio; Principe, James; Garnett, Mark; Zhang, Li

    2004-06-01

    Side-wall-curl is a springback phenomena in typical automotive structural components, such as channel like rails and cross members. Minimizing or eliminating the side-wall-curl is one of the major challenges in stamping production. This challenge is exasperated when the component is formed from advanced high strength steels (AHSS). In this study a standard three-piece draw die is used, in a series of experimental tests, to form a stamping with a hat-shaped section from dual phase 590 (DP590). During the forming stroke, the binder force is varied to evaluate its influence on side-wall-curl. FEA springback simulations for two types of experiments with varied binder forces are also performed. The binder force profiles for several sheet materials are discussed and the correlation between the simulation results and the actual part measurements are illustrated.

  3. Studying asphalt binder fatigue pattern by using a dynamic shear rheometer

    Directory of Open Access Journals (Sweden)

    Oscar Javier Reyes Ortiz

    2011-01-01

    Full Text Available This article was aimed at determining fatigue test results regarding different types of binder when using a dynamic shear rheometer (DSR. The tests were carried out in stress conditions at 20ºC. The stress input signal was a constant amplitude, 1.59 Hz frequency sine wave. Asphalt binders B-13/22, B-40/50, B-60/70, B-80/00, B-150/200 and BM-3c (modified asphalt were studied. The test measured strain, complex modulus (G*, dissipated energy and dissipated energy ratio (DER with the number of cycles. Strain criteria were used for determining binder fatigue failure (DER. Failure was defined as the point at which (DER dropped 10% after peaking. Laws of asphalt fatigue were obtained from the strain and failure cycle results.

  4. Chloride accelerated test: influence of silica fume, water/binder ratio and concrete cover thickness

    Directory of Open Access Journals (Sweden)

    E. Pereira

    Full Text Available In developed countries like the UK, France, Italy and Germany, it is estimated that spending on maintenance and repair is practically the same as investment in new constructions. Therefore, this paper aims to study different ways of interfering in the corrosion kinetic using an accelerated corrosion test - CAIM, that simulates the chloride attack. The three variables are: concrete cover thickness, use of silica fume and the water/binder ratio. It was found, by analysis of variance of the weight loss of the steel bars and chloride content in the concrete cover thickness, there is significant influence of the three variables. Also, the results indicate that the addition of silica fume is the path to improve the corrosion protection of low water/binder ratio concretes (like 0.4 and elevation of the concrete cover thickness is the most effective solution to increase protection of high water/binder ratio concrete (above 0.5.

  5. Development of a Polyuretbane Binder System Giving a 'Knottable' Composite Solid Propellant

    Directory of Open Access Journals (Sweden)

    E. Devadoss

    1985-01-01

    Full Text Available Polyurethane propellants, which constitute one of the 'work-horse' binder systems in modern solid rocketry are easily amenable for tailoring the mechanical properties in terms of variations in the molecular structure of the backbone polyols, the isocyanates and stoichiometry of the reactants. The paper deals with studies in developing an advanced binder system based on poly (oxy propylene glycol and toluene-di-isocyanate, which is capable of accommodating high solids loading and conceding elongatlon at maximum stress, of more than 125 per cent. The gum-stock properties of the binder are related with those of a low molecular weight version and the results are explained based on the network theory of condensation polymers.

  6. Effect of Hydration Aging and Water Binder Ratio on Microstructure and Mechanical Properties of Sprayed Concrete

    Institute of Scientific and Technical Information of China (English)

    NIU Ditao; WANG Jiabin; WANG Yan

    2015-01-01

    In order to study the durability of sprayed concrete (shotcrete), effects of different hydration aging and water-binder ratio (w/b) on the microstructure of cement paste and basic mechanical properties of test specimens were investigated. The phase composition, mass percentage of ettringite and portland in hydration production and microstructure were characterized by X-ray diffraction (XRD), thermo gravimetry-differential scanning calorimetry (TG-DSC) and scanning electron microscopy (SEM), respectively. The experimental results showed that changes in phase composition was more signiifcant than those of water-binder ratio. With hydration aging and water-binder ratio increased, the mass percentage of ettringite and portland was decreased from 4.42%, 1.49% to 3.31%, 1.35%, respectively and the microstructure of paste was signiifcantly compacted. Likewise, the mechanical properties including cubic compressive strength and splitting tensile strength were rised obviously.

  7. The estimation of ability to reclame of moduling sands with biopolymer binders

    Directory of Open Access Journals (Sweden)

    J. Jakubski

    2011-04-01

    Full Text Available Applied up till now organic binding materials, on the basis of synthetic resins are characterised by good technological properties, but cause high emission of harmful substances. That’s why contemporary scientific researches are leading to progressive replacing the binders obtained from petrochemical materials with polymer biocomposites coming from renewable resources. Increasing concern of aliphatic polyesters such as polylactide, polycaprolactone, poly(hydroxyalkanoates and aliphatic-aromatic polyesters is caused by the possibility of using them for producing many biodegradable products. In that context it is important to expand the researches connected to using biopolymers as moulding sands binders. Contemporary authors’ papers were focused on technological properties and harmfulness for the environment of this ecological moulding sands. TThis article takes into consideration the ability to reclamation of moulding sands with biopolymer binders.

  8. The inorganic constituents of echinoderms

    Science.gov (United States)

    Clarke, F.W.; Wheeler, W.C.

    1915-01-01

    In a recent paper on the composition of crinoid skeletons we showed that crinoids contain large quantities of magnesia, and that its proportion varies with the temperature of the water in which the creatures live. This result was so novel and surprising that it seemed desirable to examine other echinoderms and to ascertain whether they showed the same characteristics and regularity. A number of sea urchins and starfishes were therefore studied, their inorganic constituents being analyzed in the same manner as those of the crinoids

  9. Plasma chemistry for inorganic materials

    Science.gov (United States)

    Matsumoto, O.

    1980-01-01

    Practical application of plasma chemistry to the development of inorganic materials using both low temperature and warm plasmas are summarized. Topics cover: the surface nitrification and oxidation of metals; chemical vapor deposition; formation of minute oxide particles; the composition of oxides from chloride vapor; the composition of carbides and nitrides; freezing high temperature phases by plasma arc welding and plasma jet; use of plasma in the development of a substitute for petroleum; the production of silicon for use in solar cell batteries; and insulating the inner surface of nuclear fusion reactor walls.

  10. Linking asphalt binder fatigue to asphalt mixture fatigue performance using viscoelastic continuum damage modeling

    Science.gov (United States)

    Safaei, Farinaz; Castorena, Cassie; Kim, Y. Richard

    2016-08-01

    Fatigue cracking is a major form of distress in asphalt pavements. Asphalt binder is the weakest asphalt concrete constituent and, thus, plays a critical role in determining the fatigue resistance of pavements. Therefore, the ability to characterize and model the inherent fatigue performance of an asphalt binder is a necessary first step to design mixtures and pavements that are not susceptible to premature fatigue failure. The simplified viscoelastic continuum damage (S-VECD) model has been used successfully by researchers to predict the damage evolution in asphalt mixtures for various traffic and climatic conditions using limited uniaxial test data. In this study, the S-VECD model, developed for asphalt mixtures, is adapted for asphalt binders tested under cyclic torsion in a dynamic shear rheometer. Derivation of the model framework is presented. The model is verified by producing damage characteristic curves that are both temperature- and loading history-independent based on time sweep tests, given that the effects of plasticity and adhesion loss on the material behavior are minimal. The applicability of the S-VECD model to the accelerated loading that is inherent of the linear amplitude sweep test is demonstrated, which reveals reasonable performance predictions, but with some loss in accuracy compared to time sweep tests due to the confounding effects of nonlinearity imposed by the high strain amplitudes included in the test. The asphalt binder S-VECD model is validated through comparisons to asphalt mixture S-VECD model results derived from cyclic direct tension tests and Accelerated Loading Facility performance tests. The results demonstrate good agreement between the asphalt binder and mixture test results and pavement performance, indicating that the developed model framework is able to capture the asphalt binder's contribution to mixture fatigue and pavement fatigue cracking performance.

  11. On the measurement of surface tension in binders used for moulding sands

    Directory of Open Access Journals (Sweden)

    B. Hutera

    2008-07-01

    Full Text Available The surface tension of foundry binders is a very important parameter affecting the properties of a sand-binder system. Combined with other parameters, its value determines an outcome of the process of moulding sand preparation and the mechanical properties of the ready moulding composition. The problem of how to measure the surface tension of binders used in preparation of moulding sands is discussed only occasionally. Indirectly, the surface tension is characterised by the value of a contact angle, but it never means that these two parameters can be considered identical. Numerous methods are available and used at present to measure the surface tension, among others, the capillary rise method, the spinning drop method, the sessile drop method, the pendant drop method, the method of pulled out ring (or plate, or frame. There is also a rich variety of devices offered with different measuring methods. The devices are modern and represent a high level of the technical skill and art. Unfortunately, also their price is high. It is, however, possible to obtain the reliable results of the surface tension measurement using relatively simple methods, viz. the stalagmometric method and the capillary rise method. What is necessary are proper conditions of the measurement, directly related with the specific properties of binders. The present paper gives examples of the results obtained during measurement of the surface tension of some selected binders. Attention was drawn to the methods of taking measurements, and the obtained results were discussed and analysed. The possibilities of detemining the surface tension of the examined binders from the results of the contact angle measurements using the “sessile drop” and “pendant drop” methods were outlined.

  12. Application of microwave energy for curing of molding sands containing oil binders

    Directory of Open Access Journals (Sweden)

    M. Stachowicz

    2008-07-01

    Full Text Available This works presents the results of studies concerning possibility of application of microwave heating in the curing process of molding sands containing oil binders. Molding sands prepared with three kinds of binders, that is oils C, DL and Retanol, have been subject to experiments. The sands have been dried with two methods: in a microwave chamber of 750W power and, for comparison, with classical method at the temperature of 200°C for 120 minutes. Tensile and bending strength of the samples have been determined after cooling down. It has been found that microwave drying in the low-power device used for experiments is effective only in case of molding sand prepared with addition of DL binder. The temperature of heated, even up to 32 minutes in a microwave chamber, blocks prepared from the remaining two masses, was insufficient to initiate binding process. The undertaken attempts of binder modification and introduction of additives intensifying microwave heating process allowed for achievement of satisfactory results. It has been found that power of the heating device is the main factor determining efficiency of microwave curing of molding sands containing oil binders. An additional experiment has been conducted on a laboratory workstation allowing for microwave heating of small mass samples with a high output power of magnetron concentrated in a small substrate volume. It has been observed that microwave drying process of molding sands was of dynamic character over a short period of time, not exceeding 120 seconds, thus assuring efficient curing of the sands containing the used oil binders. Therefore, application of devices of properly high microwave output power allows for efficient drying of oil molding sands, while simultaneously assuring the possibility to reduce time and energy consumption necessary for production of foundry cores of proper functional characteristics.

  13. Effect of coal tar pitch modified by sulfur as a binder on the mechanical and tribological properties of bronze-impregnated carbon-matrix composites

    Energy Technology Data Exchange (ETDEWEB)

    Yang Huijun [School of Physics and Nuclear Energy Engineering, Beijing University of Aeronautics and Astronautics, No. 37, Xue Yuan Road, Hai Dian District, Beijing 100191 (China); Luo Ruiying, E-mail: ryluo@buaa.edu.cn [School of Physics and Nuclear Energy Engineering, Beijing University of Aeronautics and Astronautics, No. 37, Xue Yuan Road, Hai Dian District, Beijing 100191 (China)

    2011-03-15

    Research highlights: {yields} Sulfur addition increased the softening point and carbon yield of coal tar pitch. {yields} The mechanical properties of the composites reached a maximum at 7 wt. % of sulfur. {yields} The friction coefficient rose monotonously with increasing the content of sulfur. {yields} The wear rate of the composites reached a minimum at 7 wt. % of sulfur. {yields} The wear mechanism of composites was adhesive wear, abrasive wear and oxidative wear. - Abstract: Bronze-impregnated carbon-matrix composites were prepared through compression molding, carbonization and impregnation. The mechanism of sulfuration was studied, and the effect of coal tar pitch modified by sulfur as a binder on the mechanical and tribological properties of composites was investigated by varying the content of sulfur. The results showed that the sulfur addition increased the softening point, carbon yield and C/H atomic ratio of coal tar pitch but decreased the toluene solubility and quinoline solubility due to the dehydrogenating polymerization of pitch molecules. The micro-hardness, bending strength and compressive strength of the composites were enhanced by increasing the mass percentage of sulfur and reached a maximum of 160 HV, 132.82 MPa and 293 MPa at 7 wt. % of sulfur, respectively. However, both the hardness and strength of the composites decreased as the content of sulfur increased beyond 7 wt. %. The friction coefficient value of composites increased monotonously, but the wear rate decreased with increasing sulfur content; subsequently, the wear rate reached a minimum of 3.045 x 10{sup -7} mm{sup 3}/Nm at 7 wt. % of sulfur and then ascended. The wear mechanisms of the composites were adhesive wear, abrasive wear and oxidative wear. However, adhesive wear and oxidative wear occurred slightly for the composites with the binder modified by sulfur.

  14. EVALUATION OF MORINGA OLEIFERA GUM AS A BINDER IN TABLET FORMULATION

    OpenAIRE

    Patil Basawaraj S; Soodam Srinivas R.; Kulkarni Upendra; Korwar Prakassh G.

    2010-01-01

    Various plant gums have been used as binders in tablet formulations. But still finding novel binder for the manufacture of tablets, in pharmaceutical industry. The Moringa oleifera gum was found its binding property. In the present study Moringa oleifera gum was employed as a binding agent in Chloroquine phosphate tablets at concentrations of 4.0, 6.0 and 8.0 % w/w, in comparison with potato starch. The properties of Moringa oleifera gum were evaluated for angle of repose, bulk density, tappe...

  15. Guanidine based vehicle/binders for use with oxides, metals and ceramics

    Science.gov (United States)

    Philipp, Warren H. (Inventor); Weitch, Lisa C. (Inventor); Jaskowiak, Martha H. (Inventor)

    1995-01-01

    The use of guanidine salts of organic fatty acids (guanidine soaps) as vehicles and binders for coating substrate surfaces is disclosed. Being completely organic, the guanidine soaps can be burned off leaving no undesirable residue. Of special interest is the use of guanidine 2-ethyl hexanoate as the vehicle and binder for coating problematic surfaces such as in coating alumina fibers with platinum or zirconia. For this application the guanidine soap is used as a melt. For other applications the guanidine soap may be used in a solution with a variety of solvents, the solution containing chlorometalates or powdered metals, refractories or ceramics.

  16. Selective catalytic reduction system and process using a pre-sulfated zirconia binder

    Science.gov (United States)

    Sobolevskiy, Anatoly; Rossin, Joseph A.

    2010-06-29

    A selective catalytic reduction (SCR) process with a palladium catalyst for reducing NOx in a gas, using hydrogen as a reducing agent is provided. The process comprises contacting the gas stream with a catalyst system, the catalyst system comprising (ZrO.sub.2)SO.sub.4, palladium, and a pre-sulfated zirconia binder. The inclusion of a pre-sulfated zirconia binder substantially increases the durability of a Pd-based SCR catalyst system. A system for implementing the disclosed process is further provided.

  17. ISRO Polyol - The Versatile Binder for Composite Solid Propellants for Launch Vehicles and Missiles

    Directory of Open Access Journals (Sweden)

    V. N. Krishnamurthy

    1987-01-01

    Full Text Available A family of propellants based on a low cost hydroxy terminated binder has been developed and proved in large size motors. It can meet the requirements of Apogee motors as well as large boosters. The system offers advantages comparable with HTPB propellants in terms of high ballistic performance, stringent mechanical properties, ease and reliability of cure even at ambient conditions and high storage stability. The near-Newtonian flow behaviour, simplicity and processing characteristics of this saturated binder propellant are particularly note-worthy.

  18. Study on Heat Hardening Mechanism of Starch Composite Binder for Sand Mold (Core) by IR Spectra

    Institute of Scientific and Technical Information of China (English)

    Xia ZHOU; Jinzong YANG; Qin GAO; Guohui QU

    2001-01-01

    The heat hardening mechanism of starch composite binder for sand mold (core) was studied by way of IR spectra. It is thought that the bonding strength of molding sand is mainly depended on the strength of the adhesive membrane itself. During heating the binder at certain temperature between 160~200℃ for one hour, a special composite structure is formed because of the interactions between different components, thus, it has higher low-temperature drying strength,better humidity resistance and higher high-temperature strength.

  19. Infrared Spectra of Simple Inorganic Ion Pairs in Solid Solution: A Physical Inorganic Chemistry Experiment.

    Science.gov (United States)

    Miller, Philip J.; Tong, William G.

    1980-01-01

    Presents a physical inorganic experiment in which large single crystals of the alkali halides doped with divalent ion impurities are prepared easily. Demonstrates the ion pairing of inorganic ions in solid solution. (CS)

  20. VISCOSITY AND BINDER COMPOSITION EFFECTS ON TYROSINASE-BASED CARBON PASTE ELECTRODE FOR DETECTION OF PHENOL AND CATECHOL

    Science.gov (United States)

    The systematic study of the effect of binder viscosity on the sensitivity of a tyrosinase-based carbon paste electrode (CPE) biosensor for phenol and catechol is reported. Silicon oil binders with similar (polydimethylsiloxane) chemical composition were used to represent a wid...

  1. Effects of Nanosilica on Compressive Strength and Durability Properties of Concrete with Different Water to Binder Ratios

    Directory of Open Access Journals (Sweden)

    Forood Torabian Isfahani

    2016-01-01

    Full Text Available The effects of the addition of different nanosilica dosages (0.5%, 1%, and 1.5% with respect to cement on compressive strength and durability properties of concrete with water/binder ratios 0.65, 0.55, and 0.5 were investigated. Water sorptivity, apparent chloride diffusion coefficient, electrical resistivity, and carbonation coefficient of concrete were measured. The results showed that compressive strength significantly improved in case of water/binder = 0.65, while for water/binder = 0.5 no change was found. Increasing nanosilica content, the water sorptivity decreased only for water/binder = 0.55. The addition of 0.5% nanosilica decreased the apparent chloride diffusion coefficient for water/binder = 0.65 and 0.55; however, higher nanosilica dosages did not decrease it with respect to reference value. The resistivity was elevated by 0.5% nanosilica for all water/binder ratios and by 1.5% nanosilica only for water/binder = 0.5. The carbonation coefficient was not notably affected by increasing nanosilica dosages and even adverse effect was observed for water/binder = 0.65. Further information of microstructure was also provided through characterization techniques such as X-ray diffraction, thermal gravimetric analysis, mercury intrusion porosimetry, and scanning electron microscopy. The effectiveness of a certain nanosilica dosage addition into lower strength mixes was more noticeable, while, for the higher strength mix, the effectiveness was less.

  2. First Observation of the Blending Zone Morphology at the Interface of Reclaimed Asphalt Binder and Virgin Bitumen

    NARCIS (Netherlands)

    Nahar, S.N.; Mohajeri, M.; Schmets, A.J.M.; Scarpas, T.; Van de Ven, M.F.C.; Schitter, G.

    2013-01-01

    One of the challenges in designing recycled asphalt mixtures with a high amount of RAP is to estimate the blending degree between RAP binder and the added virgin bitumen. The extent of blending is crucial in this case as asphalt concrete response is influenced by the final binder properties. This pa

  3. Assessment of the potential for refinery applications of inorganic membrane technology: An identification and screening analysis. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, H.E.; Schulman, B.L.

    1993-05-01

    Commercial application of membrane technology in the separation of gas, liquid, and solid streams has grown to a business with worldwide revenues exceeding $1 billion annually. Use of organic membranes for industrial gas separation, particularly in the refining industry, is one of the major growth areas. However, organic membranes based on polymeric separation barriers, are susceptible to damage by liquids, and careful precautions must be taken to retain the system integrity. Researchers are currently developing small pore sized inorganic membranes which may substantially increase the efficiency and economics in selected refinery separation applications. Expected advantages of these advanced inorganic membranes include high permeability, high selectivity, and low manufacturing cost. SFA Pacific conducted a screening analysis to identify applications for inorganic membrane technology in the petroleum refining industry and their potential cost advantages over competing separation systems. Two meetings were held in connection with this project. Copies of Viewgraphs presented by SFA Pacific at these meetings are attached in Appendices A and C. Potential high priority applications and market impacts of advanced inorganic membrane technology in the refining industry are addressed in this report, and include the following areas: Competitive separation technologies; application of those technologies; incentives for inorganic membranes; market benefits and impacts of inorganic membranes.

  4. Inorganic and hybrid inorganic-organic systems for conservative treatments of stone and wood materials

    OpenAIRE

    Bergamonti, Laura

    2015-01-01

    Inorganic and hybrid inorganic-organic systems for conservative treatments of stone and wood materials The research has focused on the synthesis, characterization and application of inorganic and hybrid inorganic-organic systems for conservative treatments of stone and wood. The wood preservatives synthesized and tested for biocidal activity are polyamidoamines functionalized with hydroxyl and siloxane groups, while the coatings applied on the stones are water based TiO2 nanosols with ...

  5. Multifunctional polymeric nanoconstructs for biomedical applications (Conference Presentation)

    Science.gov (United States)

    Decuzzi, Paolo

    2016-09-01

    Multifunctional nanoconstructs are particle-based nano-scale systems designed for the `smart' delivery of therapeutic and imaging agents. The Laboratory of Nanotechnology for Precision Medicine at the Italian Institute of Technology synthesizes polymeric nanoconstructs with different sizes, ranging from a few tens of nanometers to a few microns; shapes, including spherical, cubical and discoidal; surface properties, with positive, negative, neutral coatings; and mechanical stiffness, varying from that of cells to rigid, inorganic materials, such as iron oxide. These are the 4S parameters - size, shape, surface, stiffness - which can be precisely tuned in the synthesis process enabling disease- and patient-specific designs of multifunctional nanoconstructs. In this lecture, the application of these nanoconstructs to the detection and treatment of cancer lesions and cardiovascular diseases, such as thrombosis and atherosclerosis, is discussed. The contribution of the 4S parameters in modulating nanoconstruct sequestration by the mononuclear phagocyte system, organ specific accumulation, and blood longevity is also critically presented. These polymeric nanoconstructs can be loaded with a variety of therapeutic payloads - anti-cancer molecules (docetaxel, paclitaxel, doxorubicin), anti-inflammatory molecules (curcumin, diclofenac, celecoxib) and small biologicals (peptides, siRNAs, miRNAs); and imaging agents - optical probes; Gd and iron oxide nanoparticles for MR imaging; and radio-isotopes for Nuclear Imaging.

  6. Surface chemistry for molecular layer deposition of organic and hybrid organic-inorganic polymers.

    Science.gov (United States)

    George, Steven M; Yoon, Byunghoon; Dameron, Arrelaine A

    2009-04-21

    The fabrication of many devices in modern technology requires techniques for growing thin films. As devices miniaturize, manufacturers will need to control thin film growth at the atomic level. Because many devices have challenging morphologies, thin films must be able to coat conformally on structures with high aspect ratios. Techniques based on atomic layer deposition (ALD), a special type of chemical vapor deposition, allow for the growth of ultra-thin and conformal films of inorganic materials using sequential, self-limiting reactions. Molecular layer deposition (MLD) methods extend this strategy to include organic and hybrid organic-inorganic polymeric materials. In this Account, we provide an overview of the surface chemistry for the MLD of organic and hybrid organic-inorganic polymers and examine a variety of surface chemistry strategies for growing polymer thin films. Previously, surface chemistry for the MLD of organic polymers such as polyamides and polyimides has used two-step AB reaction cycles using homo-bifunctional reactants. However, these reagents can react twice and eliminate active sites on the growing polymer surface. To avoid this problem, we can employ alternative precursors for MLD based on hetero-bifunctional reactants and ring-opening reactions. We can also use surface activation or protected chemical functional groups. In addition, we can combine the reactants for ALD and MLD to grow hybrid organic-inorganic polymers that should display interesting properties. For example, using trimethylaluminum (TMA) and various diols as reactants, we can achieve the MLD of alucone organic-inorganic polymers. We can alter the chemical and physical properties of these organic-inorganic polymers by varying the organic constituent in the diol or blending the alucone MLD films with purely inorganic ALD films to build a nanocomposite or nanolaminate. The combination of ALD and MLD reactants enlarges the number of possible sequential self-limiting surface

  7. Low toxicity binder systems for tape cast Ce0.9Gd0.1O1.95 laminates

    DEFF Research Database (Denmark)

    Klemensø, Trine; Menon, Mohan; Ramousse, Severine

    2010-01-01

    Conventional binder systems for tape casting contain toxic phthalate plasticizers and butanone (MEK) as part of the solvent. The effects of exchanging the phthalate with a non-toxic alternative, and butanone with ethanol, were studied on laminates of high-green density CGO (Ce0.9Gd0.1O1.95) tapes....... Samples were prepared with a binder system containing DBP (dibutyl phthalate) plasticizer and MEK solvent, and with a binder system based on a non-toxic non-phthalate plasticizer and ethanol. In both systems, the weight ratio of plasticizer to the PVB (polyvinyl butyral) binder was varied between 0.......4 and 0.7. Substitution to the less toxic binder system had no adverse impacts on the microstructure. In fact, denser packing and improved homogeneity were observed with the non-phthalate-based system at ratio 0.5 indicating improved dispersion in this system. The denser packing also coincided...

  8. A facile approach to derive binder protective film on high voltage spinel cathode materials against high temperature degradation

    Science.gov (United States)

    Chou, Wei-Yu; Jin, Yi-Chun; Duh, Jenq-Gong; Lu, Cheng-Zhang; Liao, Shih-Chieh

    2015-11-01

    The electrochemical performance of spinel LiNi0.5Mn1.5O4 cathode combined with different binders at elevated temperature is firstly investigated. The water soluble binder, such as sodium carboxymethyl cellulose (CMC) and sodium alginate (SA), is compared with the polyvinylidene difluoride (PVdF) binder used in non-aqueous process. The aqueous process can meet the need of Li-ion battery industry due to environmental-friendly and cost effectiveness by replacing toxic organic solvent, such as N-methyl-pyrrolidone (NMP). In this study, a significantly improved high temperature cycling performance is successfully obtained as compared to the traditional PVdF binder. The aqueous binder can serve as a protective film which inhibits the serious Ni and Mn dissolution especially at elevated temperature. Our result demonstrates a facile approach to solve the problem of capacity fading for high voltage spinel cathodes.

  9. Design of a novel system allowing the selection of an adequate binder for solidification/stabilization of wastes

    Energy Technology Data Exchange (ETDEWEB)

    Pera, J.; Thevenin, G.; Chabannet, M. [INSA de Lyon, Villeurbanne (France)

    1997-10-01

    Literature review shows that there is a lack of complete and consistent data on waste-binder interactions. Few links exist between research on the Solidification/Stabilization (S/S) mechanisms and the formulation of binders for immobilization. Therefore, a twofold program was developed allowing both to be done in parallel. This protocol had two targets: understanding the mechanisms involved in the S/S of heavy metals for each type of binder and rating the binder capacity for fixing heavy metals. The experimental procedure relies on two substrates: (1) the study of suspensions by means of conductimetry, XRD, FTIR, DTA, SEM-EDXA, ICP, ion chromatography, and colorimetry; and (2) the study of pure pastes for leaching tests and microstructural characterization (XRD, FTIR, DTA, SEM-EDXA). Results confirm whether the pollutant modifies the hydration or not, give access to the extent of binder stabilization without taking into account the solidification part, and elucidate the mechanisms involved.

  10. In Vitro Adsorption and in Vivo Pharmacokinetic Interaction between Doxycycline and Frequently Used Mycotoxin Binders in Broiler Chickens.

    Science.gov (United States)

    De Mil, Thomas; Devreese, Mathias; Broekaert, Nathan; Fraeyman, Sophie; De Backer, Patrick; Croubels, Siska

    2015-05-06

    Mycotoxin binders are readily mixed in feeds to prevent uptake of mycotoxins by the animal. Concerns were raised for nonspecific binding with orally administered veterinary drugs by the European Food Safety Authority in 2010. This paper describes the screening for in vitro adsorption of doxycycline-a broad-spectrum tetracycline antibiotic-to six different binders that were able to bind >75% of the doxycycline. Next, an in vivo pharmacokinetic interaction study of doxycycline with two of the binders, which demonstrated significant in vitro binding, was performed in broiler chickens using an oral bolus model. It was shown that two montmorillonite-based binders were able to lower the area under the plasma concentration-time curve of doxycycline by >60% compared to the control group. These results may indicate a possible risk for reduced efficacy of doxycycline when used concomitantly with montmorillonite-based mycotoxin binders.

  11. Enhanced electrochemical properties of LiFePO4 (LFP) cathode using the carboxymethyl cellulose lithium (CMC-Li) as novel binder in lithium-ion battery.

    Science.gov (United States)

    Qiu, Lei; Shao, Ziqiang; Wang, Daxiong; Wang, Wenjun; Wang, Feijun; Wang, Jianquan

    2014-10-13

    Novel water-based binder CMC-Li is synthesized using cotton as raw material. The mechanism of the CMC-Li as a binder is reported. Electrochemical properties of batteries cathodes based on commercially available lithium iron phosphate (LiFePO4, LFP) and CMC-Li as a water-soluble binder are investigated. CMC-Li is a novel lithium-ion binder. Compare with conventional poly(vinylidene fluoride) (PVDF) binder, and the battery with CMC-Li as the binder retained 97.8% of initial reversible capacity after 200 cycles at 176 mAh g(-1), which is beyond the theoretical specific capacity of LFP. Constant current charge-discharge test results demonstrate that the LFP electrode using CMC-Li as the binder has the highest rate capability, follow closely by that using PVDF binder. The batteries have good electrochemical property, outstanding pollution-free and excellent stability.

  12. SCATTERING FROM RAMIFIED POLYMERIC SYSTEMS

    Directory of Open Access Journals (Sweden)

    M.Benhamou

    2004-01-01

    Full Text Available Here, of great interest to us is a quantitative study of the scattering properties from ramified polymeric systems of arbitrary topology. We consider three types of systems, namely ramified polymers in solution, ramified polymer blends, or ternary mixtures made of two ramified polymers of different chemical nature immersed in a good solvent. To achieve the goal of the study, use is made of the Random Phase Approximation. First we determine the exact expression of the form factor of an ideal ramified polymer of any topology, from which we extract the exact expression of its gyration radius. Using the classical Zimm's formulae and the exact form factor, we determine all scattering properties of these three types of ramified polymeric systems. The main conclusion is that ramification of the chains induces drastic changes of the scattering properties.

  13. Magnetic properties of polymerized diphenyloctatetrayne

    Energy Technology Data Exchange (ETDEWEB)

    Beristain, Miriam F.; Jimenez-Solomon, Maria F.; Ortega, Alejandra; Escudero, Roberto [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Apartado Postal 70-360, Ciudad Universitaria, Mexico DF 04510 (Mexico); Munoz, Eduardo [Instituto de Fisica, Universidad Nacional Autonoma de Mexico, Apartado Postal 20-364, Ciudad Universitaria, Mexico DF 01000 (Mexico); Maekawa, Yasunari; Koshikawa, Hiroshi [High Performance Polymer Group, Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Ogawa, Takeshi, E-mail: ogawa@unam.mx [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Apartado Postal 70-360, Ciudad Universitaria, Mexico DF 04510 (Mexico)

    2012-10-15

    A new type of metal-free ferromagnetic carbon material was obtained by thermal polymerization and electron beam irradiation of diphenyloctatetrayne (DPOT). The isothermal magnetic measurements showed hysteresis loops indicating weak but intrinsic ferromagnetism with Curie temperatures of around 600 K. Electron spin resonance spectroscopy showed that the material contained stable free radicals in the range of 10{sup 17}-10{sup 20} radicals g{sup -1} depending on the polymerization process. The ferromagnetism should be due to high radical concentration although no correlation was observed between them. It was shown that an amorphous ferromagnetic carbon could be obtained from a simple crystalline solid by heating at moderate temperatures. Highlights: Black-Right-Pointing-Pointer Diphenyloctatetrayne as a precursor for carbon with high radical concentration. Black-Right-Pointing-Pointer The carbon material consists of sp{sup 2} configuration. Black-Right-Pointing-Pointer A weak intrinsic metal-free ferromagnetism was observed for the carbon products.

  14. Functional materials in amperometric sensing polymeric, inorganic, and nanocomposite materials for modified electrodes

    CERN Document Server

    Seeber, Renato; Zanardi, Chiara

    2014-01-01

    Amperometric sensors, biosensors included, particularly rely on suitable electrode materials. Progress in material science has led to a wide variety of options that are available today. For the first time, these novel functional electrode coating materials are reviewed in this monograph, written by and for electroanalytical chemists. This includes intrinsically conducting, redox and ion-exchange polymers, metal and carbon nanostructures, silica based materials. Monolayers and relatively thick films are considered. The authors critically discuss preparation methods, in addition to chemical and

  15. Polymeric Microspheres for Medical Applications

    Directory of Open Access Journals (Sweden)

    Ketie Saralidze

    2010-06-01

    Full Text Available Synthetic polymeric microspheres find application in a wide range of medical applications. Among other applications, microspheres are being used as bulking agents, embolic- or drug-delivery particles. The exact composition of the spheres varies with the application and therefore a large array of materials has been used to produce microspheres. In this review, the relation between microsphere synthesis and application is discussed for a number of microspheres that are used for different treatment strategies.

  16. One-Dimensional Organic-Inorganic Nanocomposite Synthesized with Single-Walled Carbon Nanotube Templates

    Directory of Open Access Journals (Sweden)

    Wei Li

    2014-08-01

    Full Text Available This study reports on single-walled carbon nanotubes (SWCNT as templates for the preparation of 1D porous organic-inorganic hybrid composites. The in situ deposited SWCNT were sputter coated with Sn metal and thermally oxidized in air to form a SnO2/SWCNT nanowire framework on SiO2/Si substrate. Poly(acrylic acid (PAA was coated onto this scaffold through UV light-induced radical polymerization, which resulted in the final formation of hybrid composites. The structures of hybrid composites were investigated by scanning electron microscopy, transmission electron microscopy, infrared spectroscopy, and Raman spectroscopy. The results show that PAA was successfully coated and the structural advantage of nanowire was fairly maintained, which indicates that this framework is very stable for organic functionalization in solution. The simplicity of this method for the formation of porous organic-inorganic hybrid composites provides a potential application for nanoelectronic devices.

  17. Synthesis and characterization of organic-inorganic hybrids formed between conducting polymers and crystalline antimonic acid

    Directory of Open Access Journals (Sweden)

    Beleze Fábio A.

    2001-01-01

    Full Text Available In this paper we report the synthesis and characterization of novel organic-inorganic hybrid materials between the crystalline antimonic acid (CAA and two conductive polymers: polypyrrole and polyaniline. The hybrids were obtained by in situ oxidative polymerization of monomers by the Sb(V present in the pyrochlore-like CAA structure. The materials were characterized by infrared and Raman spectroscopy, X-ray diffraction, cyclic voltammetry, CHN elemental analysis and electronic paramagnetic resonance spectroscopy. The results showed that both polymers were formed in their oxidized form, with the CAA structure acting as a counter anion.

  18. In Vitro and In Vivo Assessment of Humic Acid as an Aflatoxin Binder in Broiler Chickens

    National Research Council Canada - National Science Library

    van Rensburg, C. Jansen; Van Rensburg, C. E. J; Van Ryssen, J. B. J; Casey, N. H; Rottinghaus, G. E

    2006-01-01

    ..., and 11.9 mg of AFB1/g of oxihumate at pH 3, 5, and 7, respectively, were calculated. The in vivo efficacy of oxihumate as an aflatoxin binder in male broiler chickens exposed to aflatoxin-contaminated feed from 7 to 42 d of age was also assessed...

  19. Polyols as filler-binders for disintegrating tablets prepared by direct compaction

    NARCIS (Netherlands)

    Bolhuis, Gerad K.; Rexwinkel, Erik G.; Zuurman, Klaas

    2009-01-01

    Background: Although polyols are frequently used as tablet excipients in lozenges, chewing tablets, and orodisperse tablets, special directly compressible (DC) forms are recommended as filler-binder in common disintegrating tablets. Aim: In this article, DC types of isomalt, lactitol, mannitol, sorb

  20. Utilization of Cellulose from Luffa cylindrica Fiber as Binder in Acetaminophen Tablets

    Directory of Open Access Journals (Sweden)

    John Carlo O. Macuja

    2015-01-01

    Full Text Available Cellulose is an important pharmaceutical excipient. This study aimed to produce cellulose from the fiber of Luffa cylindrica as an effective binder in the formulation of acetaminophen tablets. This study was divided into three phases, namely, (I preparation of cellulose from Luffa cylindrica, (II determination of the powder properties of the LC-cellulose, and (III production and evaluation of acetaminophen of the tablets produced using LC-cellulose as binder. The percentage yield of LC-cellulose was 61%. The values of the powder properties of LC-cellulose produced show fair and passable flow properties and are within the specifications of a powdered pharmaceutical excipient. The mean tablet hardness and disintegration time of the LC-cellulose tablets have a significant difference in the mean tablet hardness and disintegration time of the tablets without binder; thus the cellulose produced improved the suitability of acetaminophen in the dry compression process. However, the tablet properties of the tablets produced using LC-cellulose as binder do not conform to the specifications of the US pharmacopeia; thus the study of additional methods and excipients is recommended.