Muhammad Subekti; Endiah Puji Hastuti; Dedi Heriyanto
The design of innovative high flux research reactor (RRI) requires high power so that the capability core cooling requires to be improved by designing the faster core coolant velocity near to the critical velocity limit. Hence, the critical coolant velocity as the one of the important parameter of the reactor safety shall be measured by special equipment to the velocity limit that may induce fuel element degradation. The research aims is to calculate theoretically the critical coolant velocity and to design the special experiment equipment namely EXNal for measuring the critical coolant velocity in fuel element subchannel of the RRI. EXNal design considers the critical velocity calculation result of 20.52 m/s to determine the variation of flow rate of 4.5-29.2 m 3 /h, in which the experiment could simulate the 1-4X standard coolant velocity of RSG-GAS as well as destructive test of RRI's fuel plate. (author)
Fu, Y.; Fang, H.
The design methods of furniture are different from east to west; it has been the hotspot of the scholars. However, in terms of the theory of modern design innovation, neither the early creation theory, the modern design theory, nor the widely applied TRIZ theory can fully fit the modern furniture design innovation, so it is urgent to study the modern furniture design theory. This paper is based on the idea of TRIZ theory, using lots of literatures as data, and uses the method of statistical stratification to analyze and sort out the research of modern sitting equipment, and finally put forward the modern furniture design model, which provides new ideas and perspectives for the modern design of Chinese furniture.
Gao Ligang; Wang Zongjun
Daya Bay Nuclear Power Station has achieved good performance since its commercial operation in 1994. The equipment reliability management system that features Daya Bay characteristics has been established through constant technology introduction, digestion and innovation. It is also based on the success of operational system, equipment maintenance system and technical support system. The system lays a solid foundation for the long-term safe operation of power station. This article emphasizes on the innovation part of equipment reliability management system in Daya Bay. (authors)
Broek, T. van den; Giessen, A.M. van der
The electrical and optical equipment sector is a high-tech manufacturing sector. It is one of the most innovative sectors in Europe with investments and advances in fundamental research, applied R&D and innovation in the actual use of equipment. This sector is also one of the most global sectors
Habets, M.J.M.; Voordijk, Johannes T.; van der Sijde, Peter
Purpose – The purpose of this paper is to provide insight into the adoption process of innovative asphalt equipment in road construction and how the level of knowledge as characterised by the level of education in the companies affects this process. The emphasis is on equipment used for transporting
Pogrebnoi, Vladislav; Samorodova, Lyudmila; Shut'ko, Larisa; Yakunina, Yulia; Lyubimov, Oleg
The article deals with issues related to the development of innovative projects by engineering companies and effective marketing policy as a factor of increasing their competitiveness in the mining equipment market. The paper presents the results of the development of innovative technology in the segment of extensible belt conveyors. The necessity of marketing the innovative project is proved by the example of the development of technology for the production of the motor-drum of a belt conveyor with an adjustable drive on continuous current magnets by the engineering company "Transport-Electroprivod" (LLC). The authors consider the effective marketing strategy of an engineering company as an attractor of increasing demand for innovation and competitiveness in the mining equipment market. The methods of marketing promotion and promotion of innovations are considered within the framework of the ecosystem concept of J. Moore.
Full Text Available The article deals with issues related to the development of innovative projects by engineering companies and effective marketing policy as a factor of increasing their competitiveness in the mining equipment market. The paper presents the results of the development of innovative technology in the segment of extensible belt conveyors. The necessity of marketing the innovative project is proved by the example of the development of technology for the production of the motor-drum of a belt conveyor with an adjustable drive on continuous current magnets by the engineering company “Transport-Electroprivod” (LLC. The authors consider the effective marketing strategy of an engineering company as an attractor of increasing demand for innovation and competitiveness in the mining equipment market. The methods of marketing promotion and promotion of innovations are considered within the framework of the ecosystem concept of J. Moore.
Blissell, W.H.; Ciez, A.P.; Mitchell, J.L.; Winkler, C.J.
This document describes the Westinghouse Preliminary Design for the Prototypical Consolidation Demonstration Project per Department of Energy (DOE) Contract No. DE-AC07-86ID12649 and under direction of the DOE Idaho Operations Office. The preliminary design is the first step to providing the Department of Energy with a fully qualified, licensable, cost-effective spent fuel rod consolidation system. The design was developed using proven technologies and equipment to create an innovative approach to previous rod consolidation concepts. These innovations will better enable the Westinghouse system to: consolidate fuel rods in a precise, fully-controlled, accountable manner; package all rods from two PWR fuel assemblies or from four BWR fuel assemblies in one 8.5 inch square consolidated rods canister; meet all functional requirements; operate with all fuel types common to the US commercial nuclear industry with minimal tooling changeouts; and meet consolidation production process rates, while maintaining operator and public health and safety. This Preliminary Design Report provides both detailed descriptions of the equipment required to perform the rod consolidation process and the supporting analyses to validate the design
Full Text Available The increasing demand of individuation brings new challenges to traditional product design. This paper studies and analyzes three-dimensional print technology promotes the future development of product innovation design. The advantages of 3D printing equipment can help creative products enterprises shorten product manufacturing period and make them powerful in competition.
Mustakim, Achmad; Hadi, Firmanto
The condition of loading and unloading process of livestock in a number of Indonesian ports doesn’t meet the principle of animal welfare, which makes cattle lose weight and injury when unloaded. Livestock loading and unloading is done by throwing cattle into the sea one by one, tying cattle hung with a sling strap and push the cattle to the berth directly. This process is against PP. 82 year 2000 on Article 47 and 55 about animal welfare. Innovation of loading and unloading tools design offered are loading and unloading design with garbarata. In the design of loading and unloading tools with garbarata, apply the concept of semi-horizontal hydraulic ladder that connects the ship and truck directly. This livestock unloading equipment design innovation is a combination of fire extinguisher truck design and bridge equipped with weightlifting equipment. In 10 years of planning garbarata, requires a total cost of IDR 321,142,921; gets benefits IDR 923,352,333; and BCR (Benefit-Cost Ratio) Value worth 2.88. BCR value >1 means the tool is feasible applied. The designs of this loading and unloading tools are estimated up to 1 hour faster than existing way. It can also minimize risks such as injury and also weight reduction livestock agencies significantly.
Boelskifte, Per; Jørgensen, Ulrik
The new design and innovation programme at DTU is challenging some of the standard concepts dominating most engineering educations. The programme, its background, context and basic educational ideas are presented and discussed in this paper. To build competences that match the need for innovative...... and design oriented engineers in industry and society has turned out to challenge a number of the standard – and often taken for granted – concepts in engineering education still dominated world wide by rather strict norms and concepts of learning that do not challenge the students creativity and innovative...
Pinheiro-Croisel, Rebecca; Hernes, Tor
This paper explores innovation and social behaviourist theory in relation to sustainable urban projects in the highly institutionalized public sector (towns). Using empirical data from France, we examine the dynamics of a design process in which unexpected practices generated innovative urban...... into a movement of collective action, which presupposed the acquisition of a new identity. Ultimately, our objective is to combine social behaviourist theory and innovation theory and to facilitate innovative design in urban projects....
... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Equipment design. 792.61 Section 792.61...) GOOD LABORATORY PRACTICE STANDARDS Equipment § 792.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...
... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...
... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...
Mills, S.; Haist, B.; Hamilton, D.
For 8 years, JET remote operations have become more capable and confident. Many tasks have been successfully completed, even those never intended to be remote maintenance activities. The general approach to the provision of remote handling equipment at JET has been the preferred use of commercially-off-the-shelf equipment. In the areas of electrical, electronic, software and control this approach has been generally achievable. However, in the area of mechanical equipment it has been more difficult. In particular the RH tooling has been almost entirely bespoke as its requirements are highly sensitive to the design of the JET component being handled and there are many design variations. Hence, JET has required the design and manufacture of over 700 types of bespoke RH equipment. This paper will discuss the experience of introducing and developing remote handling mechanical equipment for JET. The paper will cover the relationship between the remote handling equipment and the JET component design and the potential for improving the design function. A major lesson from the introduction of remote handling to JET has been demonstration of the very close interdependency of the design of JET components with design of remote handling tooling. The JET remote handling manual was originally introduced as the vehicle to ensure remote handling compatibility by the introduction of standards. Experience has shown that in general the remote handling manual approach has been insufficient. Future fusion machines will be much more complex than JET and will demand even greater remote handling compatibility. This paper will discuss possible methods for improving this process. Equipment operating in a high radiation environment must be dependable It may spend part of its time in areas that would be extremely difficult to recover from in the case of failure. The equipment may also have a high duty cycle to minimise shutdown times and probably cannot be manually inspected on a frequent
Fjællegaard, Cecilie Bryld; Beukel, Karin; Alkærsig, Lars
The innovation literature states that scientists are core ingredients in creating technological innovations. This paper investigates whether the hiring of a designer generates aesthetic innovations by a firm. Further we investigate what the level of design knowledge of the receiving firm means...... for the firms? absorptive capacity, in terms of turning the hiring of the designer into aesthetic innovations. We explore a unique dataset containing information on firms, their hiring of designers and aesthetic innovations measured by design applications (design patents). Our findings show that hiring...... a designer does increase firms? likelihood of producing aesthetic innovations. Secondly, firms with prior experience of aesthetic innovations are more likely to apply for design registrations. Thirdly, there is a positive moderating effect of firms with prior experience of generating aesthetic innovations...
Hienerth, Christoph; Lettl, Christopher
Literature on new product development indicates that on average around 40% of new products fail across different industries (e.g., Crawford, ; Crawford and Di Benedetto, ). Out of those that survive only few become widely accepted standard equipment in the industry (Utterback, ). Literature...... they are developed. It is therefore the aim of this study to shed light on how innovations become widely accepted by large segments of the market and specifically which demand-side forces are at work. An approach suitable for pursuing this objective is to focus on those individuals who are on the leading edge...... with respect to an important market trend (lead users) and their respective peer communities. As little knowledge is available, an explorative case study design is applied, working with cases from two different industries, specifically the medical equipment and sporting equipment industry. A longitudinal...
Meals, Clifton; Wang, Jeffrey
Orthopaedists make great use of eponymous equipment, however the origins of these tools are unknown to many users. This history enriches, enlightens, and enhances surgical education, and may inspire modern innovation. We explored the origins of common and eponymous orthopaedic equipment. We selected pieces of equipment named for their inventors and in the broadest use by modern orthopaedists. We do not describe specialized orthopaedic implants and instruments owing to the overwhelming number of these devices. The history of this equipment reflects the coevolution of orthopaedics and battlefield medicine. Additionally, these stories evidence the primacy of elegant design and suggest that innovation is often a process of revision and refinement rather than sudden inspiration. Their history exposes surgical innovators as brilliant, lucky, hardworking, and sometimes odd. These stories amuse, enlighten, and may inspire modern orthopaedists to develop creative solutions of their own. The rich history of the field's eponymous instruments informs an ongoing tradition of innovation in orthopaedics.
The total construction cost of a nuclear power plant, equipment procurement cost accounts for about 47%-53%. Whether the quality of equipment can meet the technical requirements plays a significant role in the operation and maintenance of a nuclear power plant. Only if we adopt effective management can the equipment quality be ensured. As the most important method of quality control, the effective attendance and track of quality witness points has a crucial effect on contract smooth implementation as well. The essay mainly illustrates the method of quality witness point tracing and management and how to incorporate serious minded ideas and all take part in ways into quality management, hoping to offer some enlightenment on the innovation of nuclear power equipment quality management. (author)
Sreekanth, S.; Kumar, Prabhat
• PFBR equipment erection was a challenging task where thin walled vessels had transported and handled with utmost precautions to avoid redial forces on the vessels, which could buckle the vessels. • There was a real challenge in lifting the vessels without swing, placement of large size and heavy vessel at a distance of 57 meters where the crane operator has no line of sight to equipment's being erected. • Lot of care had been taken during lifting, handling and erection of thin walled ODC with innovative methods used for lifting fixtures, guiding arrangements, alignment fixtures and achieved the stringent erection tolerances
Agger, Annika; Sørensen, Eva
Recent approaches to enhancing public innovation suffer from two shortcomings: They overemphasize competition as a driver of innovation and overlook the fact that public sector innovation involves policy innovation as well as service innovation. Drawing on governance research and innovation theory......, the chapter investigates the extent to which and how collaboration between politicians and relevant stakeholders can spur the formulation, implementation and diffusion of new innovative policies. A case study of a process of collaborative policy innovation in a Danish municipality shows that collaborative...... policy arenas do contribute to policy innovation but also that the degree to which they do so depends on the institutional design of these arenas....
This document is intended to be used as guidance for design engineers who are involved in design of new equipment slated for use in Flammable Gas Waste Storage Tanks. The purpose of this document is to provide design guidance for all new equipment intended for application into those Hanford storage tanks in which flammable gas controls are required to be addressed as part of the equipment design. These design criteria are to be used as guidance. The design of each specific piece of new equipment shall be required, as a minimum to be reviewed by qualified Unreviewed Safety Question evaluators as an integral part of the final design approval. Further Safety Assessment may be also needed. This guidance is intended to be used in conjunction with the Operating Specifications Documents (OSDs) established for defining work controls in the waste storage tanks. The criteria set forth should be reviewed for applicability if the equipment will be required to operate in locations containing unacceptable concentrations of flammable gas
the development of the new equipment, but also constantly innovates those already verified by practice. The compact and rugged design, easy operation, sensitive detectors and advanced software support made the products the essential part of radiation monitoring networks.ENVINET delivers innovative solutions also as the authorized distributor of renowned brands Thermo Fisher Scientific, ORTEC and Hidex. These are meeting the needs for faster and more accurate detection and identification while preserving simple handling. (author)
Full Text Available Organizations globally look to design to help them innovate, differentiate, and compete in a changing economic climate. Consequently, design is increasingly being regarded as a dynamic and central tactical business resource. Considering this, the question is raised: how can the specific knowledge and skills of designers be better articulated, understood, implemented, and valued as core components of strategic innovation in businesses? In seeking to answer this question, this paper proposes a new frontier for the design profession, coined the “Design Innovation Catalyst” (DIC. This paper reflects on both extant literature and the teaching of seven DICs embedded in industry, conducting innovation projects run over a twelve to twenty-four month period. This paper reports on a unique set of six capabilities analyzed as being not only essential for the implementation of design-led innovation, but of great assistance in overcoming its associated challenges. This paper outlines the role of these new design professionals, and discusses the value these novel capabilities provide organizations through employing DICs. Furthermore, questions surrounding how designers will develop these new capabilities, and how the design-led innovation framework in application can contribute to the future of design will also be presented.
Full Text Available Abernathy's (1978 empirical work on the automotive industry investigated relationships among an organization’s boundary (all manufacturing plants, its organizational design (fluid vs. specific, and its ability to execute product and/or process innovations. Abernathy's ideas of dominant designs and the locus of innovation have been central to scholars of innovation, R&D, and strategic management. Similarly, building on March and Simon's (1958 concept of organizations as decision making systems, Woodward (1965, Burns and Stalker (1966, and Lawrence and Lorsch (1967 examined relationships among organizational boundaries, organization structure, and innovation in a set of industries that varied by technology and environmental uncertainty. These and other early empirical works have led a diverse group of scholars to develop theories about firm boundaries, organization design, and the ability to innovate.
Mustaquim, Moyen; Nyström, Tobias
The concept of open innovation is becoming an increasingly popular topic of interest and seems to promise a lot in organizational development. However, to date there are no certain design principles that can be followed by organizations on how to use open innovation successfully. In this paper seven design principles of open innovation concept have been proposed. The derived principles are the outcome which is based on the principles of universal design. The open innovation design, based on t...
In the last decade, design innovation has gained increasing prominence in the marketplace, with a growing number of firms innovating not only through technology but also through novel product forms (i.e., design). However, while the effect of technological innovation on product sales is a heavily studied topic, a defining theory of how design innovation influences product sales is still missing. This paper provides demand- and supply-side theories to formulate a set of coherent hypothes...
Alkærsig, Lars; Fjællegaard, Cecilie Bryld; Beukel, Karin
the growing interest of firms in aesthetic innovations, knowledge on the ir determinants is limited. Work on labor mobility with in the innovation studies literature focuses mainly on discussion of scientists as crucial for creating technological innovations. This paper adds to work on labor mobility......Aesthetic innovations have become increasingly important appropriation mechanisms for firms. Since 2003, the number of design patent applications (to protect aesthetic innovations) has tripled compared to doubling in the numbers of both patent and trademark applications. However, despite...... and innovation by examining whether this holds in the case of designers' mobility and aesthetic innovations. Does the hiring of a new designer generate more aesthetic innovations than in a matched firm, which does not hire a designer? What is the importance of prior experience with aesthetic innovation...
Fjællegaard, Cecilie Bryld; Beukel, Karin; Alkærsig, Lars
The innovation literature states that scientists are core ingredients in creating technological innovations. This paper investigates whether the hiring of a designer generates aesthetic innovations by a firm. Further we investigate what the level of design knowledge of the receiving firm means fo...
This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage
Bradshaw, F.W., Westinghouse Hanford
This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage.
Durand, S.; Mallard, H.
Design by analysis has been particularly pointed out by the european pressure equipment directive. Advanced mechanical analysis like finite element method are used instead of classical design by formulas or graphs. Structural behaviour can be understood by the designer. Design by analysis of metallic pressure equipments is widely used. Material behaviour or limits analysis is based on sophisticated approach (elasto-plastic analysis,..). Design by analysis of composite pressure equipments is not systematically used for industrial products. The difficulty comes from the number of information to handle. The laws of mechanics are the same for composite materials than for steel. The authors want to show that in design by analysis, the composite material approach is only more complete than the metallic approach. Mechanics is more general but not more complicated. A multi-material approach is a natural evolution of design by analysis of composite equipments. The presentation is illustrated by several industrial cases - composite vessel: analogy with metallic calculations; - composite pipes and fittings; - welding and bounding of thermoplastic equipments. (authors)
Liem, André; Brangier, Eric
In this conceptual article the topic of "Prospective Ergonomics" will be discussed within the context of innovation, design thinking and design processes & methods. Design thinking is essentially a human-centred innovation process that emphasises observation, collaboration, interpretation, visualisation of ideas, rapid concept prototyping and concurrent business analysis, which ultimately influences innovation and business strategy. The objective of this project is to develop a roadmap for innovation, involving consumers, designers and business people in an integrative process, which can be applied to product, service and business design. A theoretical structure comprising of Innovation perspectives (1), Worldviews supported by rationalist-historicist and empirical-idealistic dimensions (2) and Models of "design" reasoning (3) precedes the development and classification of existing methods as well as the introduction of new ones.
In this paper innovation by design is characterised schematically and methodological with the aim of analysing how projects of innovation by design can be managed. First, I approach innovation by design from an engineering perspective, and show that the incorporation of innovation into design
Kjærgaard, Thomas; Wahl, Christian
and it was developed to include, motivate and encourage the students to engage in more situated learning processes. The course is infamous for low attendance and for demotivating the students. The new instructional design utilized teacher-produced video-clips to qualify the students learning in the preparation...... for the lessons and new pedagogical activities during lessons to make the learning process more situated. The video-clips should also include more students through scaffolding the academic reading with video-clips. However, the outcome was not as planned. The students didn’t recognize the video......This paper presents a study of what happens when innovation of an instructional design is too innovative. The study investigates an implementation process of a new instructional design in nursing education. The new instructional design should be a step away for a functionalist approach to learning...
Full Text Available Design driven innovation has emerged to be an alternative way to generate sustainable competitive products or services. Previous research has recently revealed succesful practices of design driven innovation in various industries. However, little has been known about the creative companies that practice design driven innovation, especially in developing countries. This research investigates the existence and practices of design-driven innovation in the Indonesian creative industry. Based on interviews with the design-preneurs of the creative industry, one of the results of this study reveals how the Indonesian creative industry creates new meanings that are embedded into new products. Based on the identification, a framework to create new meaningsis resulted which consists of a set of key processes, such as sensing, sensemaking, specifying, setting up and storytelling. The practical contribution of this research is that this identified framework can be adopted by any creative companies interested in improving their innovation capability.
In this paper, an advanced and more reliable design of viscoelastic dampers for seismic mitigation of high-rise buildings is presented. The innovative design of energy-absorbing devices has some advantages, compared to the classical design, as follows: One, the device is directly subjected to shear strains and forces due to story drifts; two, the device can support its own weight during normal operations, and maintain stable for large deformations during earthquakes; three, the device can reduce the responses of a structure to horizontal as well as vertical seismic loadings; and four, the device can also decrease the responses of the floor system of a building. In this study, a ten-story building is given as an example to express the merits obtained from the new system. Comparisons of the building equipped with classical and proposed devices of viscoelastic dampers are carefully studied. Numerical results show that the energy-absorbing capacity of the new device is superior to the classical one, especially for vertical vibrations. (orig.)
Borrás, Susana; Edquist, Charles
looks into a series of issues related to the design of holistic innovation policy. With this purpose in mind, this chapter summarizes previous chapters’ identification of the problems, bottlenecks and deficiencies that can afflict innovation systems. Taken together, they provide the theoretical...... foundations for the design of holistic innovation policy, which includes not only framing the problems in the innovation system, but also considerations about policy instruments for the tasks at hand, as well as the problems generated by policy itself (unintended consequences of inefficient of incomplete...
Borrás, Susana; Edquist, Charles
of innovation policy. This serves two important purposes. Firstly, it allows the identification of problems in an innovation system that require public policy intervention through the choice of appropriate policy instruments. Secondly, it allows a theoretically based identification of input indicators......In cases where innovation indicators and data fail to serve properly as a (necessary) basis for the design of innovation policies, it often has its roots in conceptual unclarities in the underlying concepts. The aim of this paper is to provide a theoretical and conceptual basis for the design...
Efeoglu, Arkin; Møller, Charles; Serie, Michel
This paper proposes use of an Innovation Management Framework through the roll-out of Design Thinking in a multi-national company by applying adequately framed organizational governance. An Innovation Management Framework based on the principles of Design Thinking is providing central pillars...... that not only ensure effective governance. The elevation both from Innovation Management to foster Design Thinking and vice versa the Design Thinking characteristics that strengthen the corporate innovativeness through governance is in focus. With the latter in mind, this paper therefor looks on Innovation...... to be governed. An Innovation Management Framework with principles of DT may avoid uncoordinated innovation capabilities. Ultimately innovation will not be an R&D topic anymore but become part for every employee’s job, irrespective of his or her position. In a previous paper DT characteristics were evaluated...
The paper addresses issues of user conceptualisation and representation in the processes of designing and innovating artifacts and use-practices. It is informed by early as well as more recent insights from technology studies within the new sociology of technology (e.g. Akrich 1995, Bijker & Law...... and competencies. Characteristic of these projects are the interplay between the social and the technical dimensions in the process of product development, and the students are expected to apply socio-technical methodologies in their strategies. The students’ need to inform the design through iteratively...... themes ranging from user-oriented design to product redesign and workspace design, etc. It is expected that some of the insights gained from these projects may be related outside of the immediate context of the classroom, to inform the notion of competencies in engineering design and sociotechnical...
Implementation of an ex situ stabilization technique at the Sand Springs superfund site to solidify and stabilize acid tar sludges involving a quick-lime based stabilization process and innovative equipment design
McManus, R.W.; Grajczak, P.; Wilcoxson, J.C.; Webster, S.D.
An old refinery site was safely remediated a year before schedule and for 25% less than final engineering estimates for the stabilization remedy thanks to energetic project management and innovative design involving ex situ stabilization/solidification of acid tar sludges. A quicklime based process, Dispersion by Chemical Reaction (DCR trademark), was employed to solidify and stabilize (SS) over 103,000 cubic meters (135,000 cubic yards) of petroleum waste, mostly acidic tarry sludge. The SS process was selected over competing methods because it afforded minimal volume increase, could readily achieve Record of Decision (ROD) specified physical and chemical treatment goals, could be implemented with treatment equipment that minimized emissions, and could be performed with low reagent usage and at low cost. To ensure treatment goals were achieved and an accelerated schedule met, a custom designed and fabricated transportable treatment unit (TTU) was employed to implement the process. The treated material was visually soil-like in character, it was left in stockpiles for periods of time, and it was placed and compacted in the on site landfill using standard earth-moving equipment
Northey, L.M.; Thomson, J.D.
Maintenance tasks performed in locations with hostile environments and/or limited space accesses often require equipment that is operated remotely. This paper discusses considerations that should be addressed in the design of remote maintenance equipment. Some of the topics include proper material selection, interface identifications, operational feedback devices and cost limitations. These considerations add ''human engineering'' to the equipment design to assure protection of the tool and the operating personnel. Examples of remote maintenance and inspection systems that were developed by the Westinghouse Hanford Company and that utilize many of these design considerations are included
The study Cork Design: A Design Action Intervention Approach Towards Sustainable Product Innovation comprises the systematic implementation of sustainable product innovation within the Portuguese cork sector, through action research. Cork is a natural, recyclable, non-toxic, and renewable resource,
Presentation of the AFCEN (French association for nuclear power plant equipment design and construction rules) working, of its edition activity and of somes of its edited documents such as RCC-C (design and construction rules for PWR power plant fuel assemblies) and RCC-E (design and construction rules for nuclear facility electrical equipments) [fr
of technology). The paper thus challenges the orthodox linear and sequential model of innovation and diffusion, which fail to capture and problematise the complexity of the dynamics involved in sociotechnical change. The paper takes a relatively broad stance as to what constitutes sociotechnical dimensions...... of the sociotechnical dimensions of innovation processes. The paper’s analysis is itself guided by a reflexive stance as to the ‘social shaping of technology’, primarily drawing on an actor-network (ANT) understanding and perspectives based on the enculturation of innovations (e.g. inno-fusion or domestication......The paper addresses interdisciplinary approaches to the study of design and innovation processes, by gathering and critically examining research contributions to date from a number of different scholarly traditions and practices including constructivist studies, participative design activities...
Gao, Shuyong; Fu, Chaoxing; Xia, Fan; Shen, Wei
Aiming at the innovation of the contours of automobile side, this paper presents an innovative design method of vehicle side profile based on Fourier descriptor. The design flow of this design method is: pre-processing, coordinate extraction, standardization, discrete Fourier transform, simplified Fourier descriptor, exchange descriptor innovation, inverse Fourier transform to get the outline of innovative design. Innovative concepts of the innovative methods of gene exchange among species and the innovative methods of gene exchange among different species are presented, and the contours of the innovative design are obtained separately. A three-dimensional model of a car is obtained by referring to the profile curve which is obtained by exchanging xenogeneic genes. The feasibility of the method proposed in this paper is verified by various aspects.
The operation, design and interfaces of the 'Duct Vehicle' and it's associated remote handling equipment are briefly described in this document. This equipment is being designed by Spar Aerospace Ltd. for the Divertor Test Platform as part of ITER Research and Development Project L-7. Canadian Fusion Fuels Technology Project funds this work as part of the Canadian Contribution to ITER. This document describes the equipment design status at the September 1996 design review. 23 figs
Helfman Cohen, Yael
Presenting a novel biomimetic design method for transferring design solutions from nature to technology, this book focuses on structure-function patterns in nature and advanced modeling tools derived from TRIZ, the theory of inventive problem-solving. The book includes an extensive literature review on biomimicry as an engine of both innovation and sustainability, and discusses in detail the biomimetic design process, current biomimetic design methods and tools. The structural biomimetic design method for innovation and sustainability put forward in this text encompasses (1) the research method and rationale used to develop and validate this new design method; (2) the suggested design algorithm and tools including the Findstructure database, structure-function patterns and ideality patterns; and (3) analyses of four case studies describing how to use the proposed method. This book offers an essential resource for designers who wish to use nature as a source of inspiration and knowledge, innovators and sustain...
Zhang, Fuying; Lu, Ximei; Wang, Ping; Liu, Hui
Product innovative design in companies today relies heavily on individual members’ experience and creative ideation as well as their skills of integrating creativity and innovation tools with design methods agilely. Creative ideation and inventive ideas generation are two crucial stages in product innovative design process. Ideal solution is the desire final ideas for given problem, and the striving reaching target for product design. In this paper, a product innovative design process driven by ideal solution is proposed. This design process encourages designers to overcome their psychological inertia, to foster creativity in a systematic way for acquiring breakthrough creative and innovative solutions in a reducing sphere of solution-seeking, and results in effective product innovative design rapidly. A case study example is also presented to illustrate the effectiveness of the proposed design process.
The Plant Design Division provides a design service to the research and development effort at CRNL. Severe constraints, both environmentally and spatially, are placed on the design of special equipment. Several examples are given. Finally, the use of automated drafting systems is described. (author)
Poulsen, Søren Bolvig; Lassen, Astrid Heidemann; Wandahl, Søren
thinking with its principles and mind-set can facilitate a common and collaborative effort within a value chain towards a joint innovative practice. Design thinking is unfolded through existing literature and it’s virtue as a facilitating and joining approach is tested through the application within...... the research project Innodoors. It is concluded user-centred material through the video media can enable practitioners from a value chain to establish a common understanding of innovation paths – potential directions for innovation. In addition it is concluded that design thinking can be adapted...... innovation has added significant aspects to the field of innovation management (e.g. Chesbrough, 2003) and companies can innovate with user collaboration or amplified notion of user together with hybrid collaborative constellations and new ways of working (von Hippel 2005). This paper examines how design...
Full Text Available The article presents modern methods of hydraulic design of an innovative small diameter gravity sewerage system. In this system, domestic wastewater is preliminary treated in septic tanks equipped with outlet filters, thus the effluent features are similar to those of clear water. Innovative non-return valves at the outlets eliminate introduction of air to the system and thus the flows can be treated as one-phase ones. Computer codes EPANET 2 and SWMM 5.0 were applied and compared. Two flow schemes typical for the sewerage system were implemented in EPANET 2, and the third - in a slightly modified SWMM 5.0. Simulation results were validated on empirical data obtained on a laboratory physical model, consisting of four tanks of minimum volumes 600 dm3 each, connecting PE pipelines of diameters 25 mm and 36 mm and relevant sanitary fittings. Water inflows, typical for domestic wastewater outflows from single homesteads, were provided by a pump. Water flows were measured using water meters with pulse outputs, and water levels in tanks by pressure transducers. Hydraulic characteristics of filters and non-return valves were provided. Simulation results showed good agreement with the empirical data. Ranges of values of design parameters, needed for successful application of both codes, were established and discussed.
A new CMS tracker is scheduled to become operational for the LHC Phase 2 upgrade in the early 2020's. tkLayout is a software package developed to create 3d models for the design of the CMS tracker and to evaluate its fundamental performance figures. The new tracker will have to cope with much higher luminosity conditions, resulting in increased track density, harsher radiation exposure and, especially, much higher data acquisition bandwidth, such that equipping the tracker with triggering capabilities is envisaged. The design of an innovative detector involves deciding on an architecture offering the best trade-off among many figures of merit, such as tracking resolution, power dissipation, bandwidth, cost and so on. Quantitatively evaluating these figures of merit as early as possible in the design phase is of capital importance and it is best done with the aid of software models. tkLayout is a flexible modeling tool: new performance estimates and support for different detector geometries can be quickly ad...
Full Text Available Without creativity in design there is no potential for innovation. This paper investigates the role of contradictions in enhancing creativity in product design. Based on the inventive principles of TRIZ, this paper presents a novel design method by integrating technical and physical contradiction analysis methods into the conceptual design activities of new product development (NPD. Despite the recognized importance of innovative design, there is a lack of the systematic and effective design-thinking process that can covers all conceptual design activities. To address this gap, a sharper and fundamental model of the problem-solving is created for innovative product design based on the contradiction-oriented concept. Eventually, one case study is employed to illustrate the method and the result validates that it can help designers produce more creative outcomes in product design.
Hienonen, R.; Karjalainen, M.; Lankinen, R. [VTT Automation, Espoo (Finland). ProTechno
The project `Verification of the thermal design of electronic equipment` studied the methodology to be followed in the verification of thermal design of electronic equipment. This project forms part of the `Cool Electronics` research programme funded by TEKES, the Finnish Technology Development Centre. This project was carried out jointly by VTT Automation, Lappeenranta University of Technology, Nokia Research Center and ABB Industry Oy VSD-Technology. The thermal design of electronic equipment has a significant impact on the cost, reliability, tolerance to different environments, selection of components and materials, and ergonomics of the product. This report describes the method for verification of thermal design. It assesses the goals set for thermal design, environmental requirements, technical implementation of the design, thermal simulation and modelling, and design qualification testing and the measurements needed. The verification method covers all packaging levels of electronic equipment from the system level to the electronic component level. The method described in this report can be used as part of the quality system of a corporation. The report includes information about the measurement and test methods needed in the verification process. Some measurement methods for the temperature, flow and pressure of air are described. (orig.) Published in Finnish VTT Julkaisuja 824. 22 refs.
Christensen, Poul Rind; Junginger, Sabine
Designing, as an activity, is squeezed in a paradoxical agency between reproduction and innovation of meanings in society as well as in the organization. In this conceptual paper the apparent paradox is addressed in perspective of the organizational culture theory and examine the role of design...... in reproducing and innovating dominant organizational cultures....
Wang, Donglin; Wei, Zihui; Wang, Youjiang; Tan, Runhua
Products innovation is under the prerequisite of realizing the new function, the realization of the new function must solve the contradiction. A new process model of new product innovative design was proposed based on Axiomatic Design (AD) Theory and Functional Structure Analysis (FSA), imbedded Principle of Solving Contradiction. In this model, employ AD Theory to guide FSA, determine the contradiction for the realization of the principle solution. To provide powerful support for innovative design tools in principle solution, Principle of Solving Contradiction in the model were imbedded, so as to boost up the innovation of principle solution. As a case study, an innovative design of button battery separator paper punching machine has been achieved with application of the proposed model.
Full Text Available Innovation enables companies to attain consistent organic growth that brings benefits to stakeholders. Designthinking approach in innovation has been emergent to be an alternative to technological development path inorder to generate competitive and successful product or service in the market place. Design driven innovationcombines functional and semantic dimensions of products or services in the marketplace. Previous researchhas recently revealed practices of design driven innovation in various industries. However, little is known tothe extent that companies in Indonesia practicing design driven innovation. A theoretical framework withperspective from dynamic capability theoretical lens and guided by Dubin’s theory building methodology isproposed to explain the constructs and role of design in the process of innovation. The research is expected tocontribute a new construct to the existing framework, namely construct that related to how we could assessthe value of the design-driven innovation output, perceived by the costumers.Keywords: design driven innovation, dynamic capabilities, theory building
Several innovative technologies are under consideration in the world for nuclear energy production. The considered reactor systems apply either gas, sodium, lead, lead-bismuth, supercritical water, or molten salt as coolant. Therefore, methods shall be developed to determine the viability of such systems, but also to support the design of these innovative reactor systems. Computational Fluid Dynamics (CFD) is becoming more and more integrated in the daily practice of thermal-hydraulics researchers and designers. Therefore, it is very important to develop modelling approaches for the application of CFD to the specific requirements for innovative reactors. As many of these innovative reactor designs under consideration are operated using other coolants than water, one has to be careful in adopting methods which are developed for water as a coolant. Cross-cutting CFD challenges, methods and applications are presented for innovative reactors. (author)
V. A. Panfilov
Full Text Available Improving the efficiency of scientific and engineering work to develop methods for converting agricultural raw materials into food is the most important condition of output processing and food sectors of agriculture in the sixth technological structure. The purpose of this article is to formalize the process of creating a progressive technique of food technologies. The process of self-organizing technological systems, presents a model of dual mechanism of control with regard to the processes of food technology. It is shown that in the process of adaptation development of the technological system as purposefully improving the structure and functioning of the system: increases the efficiency of interaction with the external environment. This smoothed out the contradictions of the technological system and its the main thing, the main technical contradiction: «productivity – quality». The steps to be taken to ensure that the technological system of conditions for intensive development. It is concluded that the potential development of some technological systems is hidden in the perspective of automation, and others – is associated with adaptive development processes, in particular machines, devices and bioreactors. The paper shows that innovative and truly breakthrough developments leading to the creation of fundamentally new equipment and new generations of technological systems, possible only with the establishment of patterns of organization, structure, functioning and development of open systems, which are modern technologies of agriculture. The mechanism of control of technological object acts as a core of adaptive development, which implements the anti-entropic entity management object, formalizing the innovation process of innovative food processing technologies.
This book guides the design supervision, construction order for electrical equipment. The contents of this library are let's use electricity like this, leading-in-pole and casual power, electric pole install below 300KVA, electric pole install below 301∼1000KVA, electric pole install exceed 1000KVA, rooftop install exceed 1000KVA, CUBICLE type, 154KV services. It adds an appendix.
Christiansen, Ellen; Kanstrup, Anne Marie
The paper presents the history and conceptual foundation for the Mobile Design Lab, ment to support both designers and users in the acts of user-driven innovation. The Mobile Design Lab is based on Vygotsky's theory of tool- and language-mediation, and was created in 2004 to support research...... and teaching of user driven innovation. Being itself an example of user-driven innovation it has taken shape of HCI design research projekcts, in which we have been involved since 2004. The first challenge was to get 'out of the lab', the next to get 'out of the head', and finally we are currently working...
Alting, Leo; Andreasen, Mogens Myrup; Boelskifte, Per
of the accompanying research. It is illustrated how the development of particularly the socio-technical dimensions of design and innovation are based on a close observation of the challenges facing industry. The new competences are expected to support modernisation of industrial methods and organisational schemes......The new design & innovation programme at DTU represents a fundamental rethinking of the standard concepts dominating most engineering educations. The teaching, its background, context and basic educational ideas are presented and discussed in this paper together with the basic ideas...
Nixon, David; Miller, Christopher; Fauquet, Regis
Experimental designs in life-size mock-up form for the wardroom facility for the Space Station Habitability Module are explored and developed. In Phase 1, three preliminary concepts for the wardroom configuration are fabricated and evaluated. In Phase 2, the results of Phase 1 are combined with a specific range of program design requirements to provide the design criteria for the fabrication of an innovative medium-fidelity mock-up of a wardrobe configuration. The study also focuses on the design and preliminary prototyping of selected equipment items including crew exercise compartments, a meal/meeting table and a portable workstation. Design criteria and requirements are discussed and documented. Preliminary and final mock-ups and equipment prototypes are described and illustrated.
Dove, Graham; Halskov, Kim; Forlizzi, Jodi
be because it is a new and difficult design material. To better understand why we have witnessed little design innovation, we conducted a survey of current UX practitioners with regards to how new ML services are envisioned and developed in UX practice. Our survey probed on how ML may or may not have been...... a part of their UX design education, on how they work to create new things with developers, and on the challenges they have faced working with this material. We use the findings from this survey and our review of related literature to present a series of challenges for UX and interaction design research...... and education. Finally, we discuss areas where new research and new curriculum might help our community unlock the power of design thinking to re-imagine what ML might be and might do....
Lettl, Christopher; Gemuenden, Hans Georg; Hienerth, C.
in order to transform their radically new solutions into functional prototypes and then to convince established manufacturers of the technological and market potential of their innovations. Using a comparative case study design in the high-tech field of medical equipment technology, we find that individual...... the supply of diversified knowledge, the development and coordination of a network for further development of the innovation, and initial tests of technical or market feasibility. Our findings have implications for manufacturing firms that wish to design radical innovation projects with (individual) lead...
Banu Hatice Gurcum
Full Text Available Innovative technologies have become the most widespread rapid and flexible technique of cutting, welding, printing and coloring in fashion and textile sectors in a very short time. Laser systems as the most common used innovative technology engrave, cut, form, print, shade appropriated formatted drawings and sketches as well as they provide reliable placements for the lay out plans and precision cutting and the production sector rapid and qualified. The practical applications and conveniences that innovative Technologies employ, influence design process, designers can design in a more creative, rapid, precise and effective manner. Although design is a context where technology is effective, the style, mood and the background of the designer is still important. Designers while making innovative studies should take the advantage of the developing technologies in experimental processes and should combine technological opportunities with aesthetics. Textile designer as in all other domains of design, should harmonise with the change and should define his/her style with the innovative Technologies in an innovative manner and renew him/herself all the time. This study aims to classify laser cutting technology applications available in textile and fashion sector as well as to present the laser technology as a means of process, product, material innovation and explains the contributions of laser systems to creativity.
Atasoy, P.; Bekker, M.M.; Lu, Y.; Brombacher, A.C.; Eggen, J.H.; Melkas, H.; Buur, J.
Design and innovation workshops are common practices to match diverse stakeholders to initiate collaboration for innovation. Due to the complex and multi-faceted processes in such a collaboration workshop, not only the toolkits but also the facilitation of the process needs to be taken into account.
Full Text Available With the innovation of mobile internet technology and intelligent terminal technology, the wearable equipment has been gradually applied in various industries. Through the typical application of wearable equipment, the characteristics of wearable equipment technology and application are summarized. Based on the analysis of power field business application and technology, combined with the demand of electric field management, the design situation of the wearable equipment in electric field service is designed, and the future development direction of electric field wear can be forecasted.
Lenau, Torben Anker; Barfoed, Michael; Shu, Li
Biomimetic design copies desired principles found in nature and implement them into artificial applications. Applications could be products we use in our daily life but it can also be used to inspire material innovation. However there are significant challenges in performing biomimetic design. One....... This is a key issue in design and innovation work where problem identification and systematic search for suitable solution principle are major activities. One way to deal with this challenge is to use a biology search method. The use of such a method is illustrated with a case story describing the design...... including the terminology and knowledge organisation. It is often easy to recognise the splendour of a biological solution, but it can be much more difficult to understand the underlying mechanisms. Another challenge in biomimetic design is the search and identification of relevant solutions in nature...
Since the machinery, equipment and piping which compose nuclear power station facilities are diverse, when those are designed, consideration is given sufficiently to the objective of use and the importance of the object machinery and equipment so that those can maintain the soundness over the design life. In this report, on the contents and the design standard in the design techniques for nuclear reactor machinery and equipment, the way of thinking is shown, taking an example of reactor pressure vessel which is stipulated as the vessel kind 1 in the 'Technical standard of structures and others regarding nuclear facilities for electric power generation', Notice No. 501 of the Ministry of International Trade and Industry. The reactor pressure vessel of 1350 MWe improved type BWR (ABWR) is used under the condition of 87.9 kg/cm 2 and 302 degC, and the inside diameter is about 7.2 m, the inside height is about 21 m, and the wall thickness is about 170 mm. The design standard for reactor pressure vessels and its way of thinking, breakdown prevention design and the design techniques for reactor pressure vessels are described. (K.I.)
A model of fashion cycles is developed in which fashion is used as a signalling device in a "dating-game". We assume that there is a designer (monopolist) who can create new designs at a positive fixed cost and zero marginal cost. Designs are durable commodities. We show the existence of equilibria of the following form: Every T periods a new design is innovated. Over time the price of the design falls and it spreads to more and more agents. Once sufficiently many agents own the design it is ...
This paper provides a summary of maintenance equipment considerations and actual plant handling experiences from operation of a sodium-cooled reactor, the Fast Flux Test Facility (FFTF). Equipment areas relating to design, repair techniques, in-cell handling, logistics and facility services are discussed. Plant design must make provisions for handling and replacement of components within containment or allow for transport to an ex-containment area for repair. The modular cask assemblies and transporter systems developed for FFTF can service major plant components as well as smaller units. The plant and equipment designs for the Clinch River Breeder Reactor (CRBR) plant have been patterned after successful FFTF equipment
de Reuver, G.A.; Keijzer-Broers, W.J.W.
IT artifacts play an important role in solving societal problems and realizing social innovations. Existing practice-inspired design science research (DSR) approaches, such as Action Design Research (ADR), do not consider social innovation as an explicit starting point for design iterations. In this
Magnussen, Rikke; Sørensen, Birgitte Holm
This paper, which concerns criteria for developing technology-enhanced innovation education, discusses how teacher and student relationships change in these learning spaces. The case study in this paper involves a school in Denmark where teachers and students, aged 6-14, were involved in developing...... and testing new forms of technology-enhanced innovation education as part of the establishment of an EduTechLab at the school. Established in new facilities at the school, the lab contained learning technologies such as Nao robots, sensor kits, and 3D visualisation and printing facilities. The goal of the Edu......TechLab project was to establish a creative learning environment for students and teachers that would support innovative practice with new forms of learning technology. Part of this goal was to involve students in innovative design processes in order for them to experiment with their own design solutions to case...
Chapman, C.C.; Drosjack, W.P.
The vitrification process and equipment design is nearing completion for the West Valley Project. This report provides the basis and current status for the design of the major vessels and equipment within the West Valley Vitrification Plant. A review of the function and key design features of the equipment is also provided. The major subsystems described include the feed preparation and delivery systems, the melter, the canister handling systems, and the process off-gas system. 11 refs., 33 figs., 4 tabs
Al-kazzaz, Dhuha; Bridges, Alan; Chase, Scott Curland
This paper describes a new methodology of deriving innovative hybrid designs using shape grammars of heterogeneous designs. The method is detailed within three phases of shape grammars: analysis, synthesis and evaluation. In the analysis phase, the research suggests that original rules of each...... design component are grouped in subclass rule sets to facilitate rule choices. Additionally, adding new hybrid rules to original rules expands the options available to the grammar user. In the synthesis phase, the research adopts state labels and markers to drive the design generation. The former...... is implemented with a user guide grammar to ensure hybridity in the generated design, while the latter aims to ensure feasible designs. Lastly evaluation criteria are added to measure the degree of innovation of the hybrid designs. This paper describes the derivation of hybrid minaret designs from a corpus...
Kappler, J. R.; Folsom, A. B.
Maintainability must be designed into long-duration spacecraft and equipment to provide the required high probability of mission success with the least cost and weight. The ability to perform repairs quickly and easily in a space environment can be achieved by imposing specific maintainability design criteria on spacecraft equipment design and installation. A study was funded to investigate and define design criteria for electronic equipment that would permit rapid removal and replacement in a space environment. The results of the study are discussed together with subsequent simulated zero-g demonstration tests of a mockup with new concepts for packaging.
Kale, S.A.; Sapali, S.N. [College of Engineering. Mechanical Engineering Dept, Pune (India)
Among the renewable energy sources, today wind energy is the most recognized and cost effective. Developers and researchers in this sector are optimistic and continuously working innovatively to improve the technology. The wind power obtained is proportional to the swept area of wind turbine. The swept area is increased by using a single rotor of large diameter or multi rotors in array. The rotor size is growing continuously with mature technology. Multi rotor technology has a long history and the multi rotor concept persists in a variety of modern innovative systems but the concept has fallen out of consideration in mainstream design from the perception that is complex and unnecessary as very large single rotor units are now technically feasible. This work addresses the evaluation of different multi rotor wind turbine systems. These innovative wind turbines are evaluated on the basis of feasibility, technological advantages, security of expected power performance, cost, reliability, impact of innovative system, comparison with existing wind turbine design. The findings of this work will provide guidelines for the practical and economical ways for further research on the multi rotor wind turbines. (Author)
Guangwei Shao; Zhongjun Ji; Bing Liu
With the innovation of mobile internet technology and intelligent terminal technology, the wearable equipment has been gradually applied in various industries. Through the typical application of wearable equipment, the characteristics of wearable equipment technology and application are summarized. Based on the analysis of power field business application and technology, combined with the demand of electric field management, the design situation of the wearable equipment in electric field ser...
Aakjær, Marie Kirstejn
as a learning outcome, where changes in perceptions, creation of trust and the process of collaborative sense making are pivotal for change and innovation. This is conceptualised as social innovation and it is argued that the concept of social innovation in the prison and probation service presuppose...... the inclusion of human and relational elements. It is concluded that design approaches may serve as levers for social innovation, taking into consideration the interconnectedness of relations, values and assumptions of the innovators and competence in practice....
Poulsen, Søren Bolvig; Lassen, Astrid Heidemann; Wandahl, Søren
Establishing a collective innovative practice within a value chain is vital as competition often takes place between supply chains rather than individual companies (Lambert, 2006). This requires new new innovative approaches and an adaptive learning culture (Tyre and von Hippel 1997). User driven...... innovation has added significant aspects to the field of innovation management (e.g. Chesbrough, 2003) and companies can innovate with user collaboration or amplified notion of user together with hybrid collaborative constellations and new ways of working (von Hippel 2005). This paper examines how design...
Dell'era, Claudio; Marchesi, Alessio; Verganti, Roberto
Only a few companies have mastered the design-driven approach to innovation. This paper examines what it means to make design a central part of the business process, able to add value to products and create new markets. More specifically, it focuses on the interplay between the functional and sem...
Full Text Available The purpose of the study is to propose a new design process by modifying functional element design approach which can commence a large amount of innovative concepts within a short period of time. Firstly, the original creative functional elements design method is analyzed and the drawbacks are discussed. Then, the modified is proposed and is divided into 6 steps. The creative functional element representations, generalization, specialization, and particularization are used in this method. Every step is described clearly, and users could design by following the process easily. In this paper, a clear and accurate design process is proposed based on the creative functional element design method. By following this method, a lot of innovative bicycles will be created quickly.
Kleinsmann, M.S.; Valkenburg, Rianne; Sluijs, Janneke
Design thinking has become a popular notion in the field of innovation. What is design thinking really and—even more important—what could be its value in applying it in innovation practices? This paper presents four studies that together capture the value of design thinking in different
Reinders, Angele H; Brezet, Han
The Power of Design offers an introduction and a practical guide to product innovation, integrating the key topics that are necessary for the design of sustainable and energy-efficient products using sustainable energy technologies. Product innovation in sustainable energy technologies is an interdisciplinary field. In response to its growing importance and the need for an integrated view on the development of solutions, this text addresses the functional principles of various energy technologies next to the latest design processes and innovation methods. From the perspec
Information pertaining to design methods, material selection, fabrication, quality assurance, and performance tests for heat transfer equipment in water-cooled nuclear reactor systems is given in this design guide. This information is intended to assist those concerned with the design, specification, and evaluation of heat transfer equipment for nuclear service and the systems in which this equipment is required. (U.S.)
Feng, Xiancheng; Yun, Xiang
Now, most favors fiber access is mainly the EPON fiber access system. Inheriting from the low cost of Ethernet, usability and bandwidth of optical network, EPON technology is one of the best technologies in fiber access and is adopted by the carriers all over the world widely. According to the scheme analysis to FTTH fan-end equipment, hardware design of ONU is proposed in this paper. The FTTH far-end equipment software design deference modulation design concept, it divides the software designment into 5 function modules: the module of low-layer driver, the module of system management, the module of master/slave communication, and the module of main/Standby switch and the module of command line. The software flow of the host computer is also analyzed. Finally, test is made for Ethernet service performance of FTTH far-end equipment, E1 service performance and the optical path protection switching, and so on. The results of test indicates that all the items are accordance with technical request of far-end ONU equipment and possess good quality and fully reach the requirement of telecommunication level equipment. The far-end equipment of FTTH divides into several parts based on the function: the control module, the exchange module, the UNI interface module, the ONU module, the EPON interface module, the network management debugging module, the voice processing module, the circuit simulation module, the CATV module. In the downstream direction, under the protect condition, we design 2 optical modules. The system can set one group optical module working and another group optical module closure when it is initialized. When the optical fiber line is cut off, the LOS warning comes out. It will cause MUX to replace another group optical module, simultaneously will reset module 3701/3711 and will make it again test the distance, and will give the plug board MPC850 report through the GPIO port. During normal mode, the downstream optical signal is transformed into the
Kim, Han-Gon [Centural Research Institute, Daejeon (Korea, Republic of); Heo, Sun [Korea Hydro and Nuclear Power Co., Daejeon (Korea, Republic of)
Most of countries operating NPPs have been performed post-Fukushima improvements as short-term countermeasure to enhance the safety of operating NPPs. Separately, vendors have made efforts on developing passive safety systems as long-term and ultimate countermeasures. AP1000 designed by Westinghouse Electric Company has passive safety systems including the passive emergency core cooling system (PECCS), the passive residual heat removal system (PRHRS), and the passive containment cooling system (PCCS). ESBWR designed by GE-Hitachi also has passive safety systems consisting of the isolation condenser system, the gravity driven cooling system and the PCCS. Other countries including China and Russia have made efforts on developing passive safety systems for enhancing the safety of their plants. In this paper, we summarize the design goals and main design feature of innovative safe PWR, iPOWER which is standing for Innovative Passive Optimized World-wide Economical Reactor, and show the developing status and results of research projects. To mitigate an accident without electric power and enhance the safety level of PWR, the conceptual designs of passive safety system and innovative safe PWR have been performed. It includes the PECCS for core cooling and the PCCS for containment cooling. Now we are performing the small scale and separate effect tests for the PECCS and the PCCS and preparing the integral effect test for the PECCS and real scale test for the PCCS.
Nur Khasan; Samuel Praptoyo
A preliminary design of mechanical device on industrial digital radiography equipment has been done. this design is intended as a basis for the manufacture of complete facilities for the realization a prototype on industrial digital radiography equipment. the design and construction were carried out by paying attention to the general configuration of the basic design in which its mechanical design has several components with specific dimensions and heavy mass. this design consist of a main frame holder, flat panel detector support and hydraulic hand stacker for mounting the x-ray machine. this mechanical device design will then be fabricated to facilitate and assist work of digital radiographic retrieval. computer application programs sketch-up is used to draw this design and the analysis stress of autodesk inventor to analysis the strength construction design. the results of this design are the configuration drawing, sketch drawings of construction and the safety factor of construction design with a minimum value of 2.39 as well as a maximum value of 15 when to be simulated by the load 500 Kg which is 4 times of total workload. (author)
den Ouden, Elke
Innovation Design presents an approach to designing shared value for businesses, non-profit organizations, end-users and society. The societal and economic challenges we are currently facing – such as the aging population, energy scarcity and environmental issues – are not just threats but are also great opportunities for organizations. Innovation Design shows how organizations can contribute to the process of generating value for society by finding true solutions to these challenges. And at the same time it describes how they can capture value for themselves in business ecosystems that care for both people and planet. This book covers: · Creating meaningful innovations that improve quality of life, engage users and provide value for organizations and other stakeholders; · Guiding the creation of shared value throughout the innovation process, with a practical and integrative approach towards value that connects ideas from economics, psychology, sociology and ecology; ·�...
Miyabe, Kenjiro; Ninomiya, Kazushige; Jin, Kazumi; Morifuji, Masayuki; Nemoto, Kazuhiko; Sato, Akira; Kawai, Keiichi
Various kind of radiation monitoring equipment are used in radiation controlled area at each facility of Tokai reprocessing plant. These equipments have been designed and constructed based on the users requirements, and permitted by governmental regulation office. And, design has been carried out in consideration of the adoption of the new technology and our operational experience. Then, it has been used effectively for the radiation control of the facilities. This report summarizes the technical requirements that should be taken into consideration in the design and installation of radiation monitoring equipments. These requirements are fundamentally applicable when the equipments of the new facilities will be designed or the present instruments will be replaced. (author)
Corcho Corcho, C. A.; Perez Garcia, A.; Herrera Rodriguez, R.
The development experienced in the design and implementation of equipment are presented, within the subject matter of the application of low level laser and also them LED of high efficiency with therapeutic purposes in health and also in animal health, besides, the use of this technology for this application in agriculture. All the equipment that show up has been developed for the Dpto. of Bioengineer of High Politechnical Institute Jose A. Echeverria (CUJAE) in association with Dpto. of Prototypes of the same institution, under the trademark BIOFIE. Like fundamental and innovative characteristic we can make a comment that all equipment destined to health and animal health, work on continuos and modulated signal mode, using in this mode different bio frequencies. (Author)
Safety margins related to design of reactor equipment are defined according to safety regulations. Advanced best estimate methods are proposed including some examples which were computed and compared to experimental results. Best estimate methods require greater computation effort and more material data but give better variable accuracy and need careful experimental validation. Simplified methods compared to the previous are less sensitive to material data, sometimes are more accurate but very long to elaborate
Ansart, A.; Manuel, P.; Fevrier, A.
Development of superconductors for AC current and of higher critical temperature superconducting materials enlarged the field of research in cryoelectrotechnic. The paper discusses the materials characteristics in relation with the functional needs in the equipments. Are reviewed the main points governing conductor design for a given application, the characteristics and manufacturing technics for different superconducting materials. It is shown how lighter, smaller equipments can be designed as well as new ones for functions not covered with present apparatus. 17 refs [fr
Calabretta, G.; Gemser, G.; Wijnberg, N.; Hekkert, P.P.M.
Innovation and design literature have given limited consideration to the strategic role of design consultancies in the innovation processes of their clients. A plausible explanation is the difficulty to assess the quality of design consultancies’ output, given the intangibility of the output itself
Yusof, Wan Zaiyana Mohd; Fadzline Muhamad Tamyez, Puteri
The definition of innovation does not help the entrepreneurs, business person or innovator to truly grasp what it means to innovate, hence we hear that government has spend millions of ringgit on “innovation” by doing R & D. However, the result has no avail in terms of commercial value. Innovation can be defined as the exploitation of commercialization of an idea or invention to create economic or social value. Most Entrepreneurs and business managers, regard innovation as creating economic value, while forgetting that innovation also create value for society or the environment. The ultimate goal as Entrepreneur, inventor or researcher is to exploit innovation to create value. As changes happen in society and economy, organizations and enterprises have to keep up and this requires innovation. This conceptual paper is to study the radical design driven innovation in the Malaysian furniture industry as a business model which the overall aim of the study is to examine the radical design driven innovation in Malaysia and how it compares with findings from Western studies. This paper will familiarize readers with the innovation and describe the radical design driven perspective that is adopted in its conceptual framework and design process.
Due to a huge concentration of electromagnetic fields and eddy currents, large power equipment and systems are prone to crushing forces, overheating, and overloading. Luckily, power failures due to disturbances like these can be predicted and/or prevented.Based on the success of internationally acclaimed computer programs, such as the authors' own RNM-3D, Engineering Electrodynamics: Electric Machine, Transformer, and Power Equipment Design explains how to implement industry-proven modeling and design techniques to solve complex electromagnetic phenomena. Considering recent progress in magneti
Peishel, F.L.; Mouring, R.W.; Schrock, S.L.
Equipment racks have been used to support process equipment in radioactive facilities for many years. Improvements in the design of these racks have evolved relatively slowly primarily as a result of limitations in the capabilities of maintenance equipment; that is, tasks could only be approached from above using bridge cranes with viewing primarily through periscopes. In recent years, however, technological advances have been made by the Consolidated Fuel Reprocessing Program (CFRP) at Oak Ridge National Laboratory (ORNL) in bridge-mounted servomanipulators with onboard auxiliary hoists and television viewing systems. These advances permit full cell coverage by the manipulator arms which, in turn, allow maintenance tasks to be approached horizontally as well as from above. Maintainable equipment items can be stacked vertically on a rack because total overhead access is less important and maintenance tasks that would not have been attempted in the past can now be performed. These advances permit greater flexibility in the design and cell layout of the racks and lead to concepts that could significantly increase the availability of a facility. The evolution of rack design and a description of the alternative concepts based on present maintenance systems capabilities are presented in this paper. 13 refs., 11 figs
Canci, F.; Zecchin, M.
This paper describes the development of a series of gas engine driven air-water compression heat pumps designed for reversible summer-winter operation. The development work was carried out within the framework of a joint venture combing the efforts of the Italian Gas Society, Natural Gas of Barcellona and Climaveneta of Vicenza (Italy), who acted as the heat pump constructor. The main objective of this venture was to develop a series of machines that would be suitable for the contemporaneous summer air conditioning and winter space heating of medium-sized buildings. The designs were optimized to allow cost and energy savings with respect to conventional equipment. The useful cooling power range of the innovative heat pump systems goes from 100 to 250 kW thus giving them the flexibility not yet afforded by conventional equipment currently sold on international markets. In addition to pointing out the new heat pumps' main design and performance features, this paper suggests some feasible applications.
Balint, Tibor S.; Freeman, Anthony
NASA is a dynamic and living organization. Looking at it through the optics of cybernetics, we can describe it as an autopoietic system. It has to sustain itself, and compete successfully to be viable. Its organizational elements have to interact with the broader environment by maintaining and improving its processes that generate the means for future sustainability. It also needs to bring up follow-on generations who are not simply aligning with the status quo, but also improve the system's viability. For government-run programs, organizational, programmatic and project management practices are often rigidly linear. They can be characterized as observed first-order cybernetic systems, where the paradigm is bound by well-established requirements. At the implementation level this does not readily accommodate flexibility and change. To address this, broadening the system's worldview is needed from the strategic level. This corresponds to an observing second-order cybernetic system, where strategic leadership can overwrite the rules of a first-order system. Changing the worldview of an organization can be complex and face much resistance. Still, with the appropriate strategic-level support, it can be achieved by introducing novel languages, new perspectives, and adding new disciplines to existing ones. In effect, this helps to broaden the organizational paradigm, and subsequently influence its mission, impact the culture, and open up its core processes. These changes can be effectively introduced through design conversations in the early formulation stages, when new ideas are conceived. Within NASA's Jet Propulsion Laboratory, early-stage concept developments are performed at a specially formulated environment, called the Innovation Foundry. Within this office, a continuous effort is being made on designing the design processes, which helps to broaden the variety of the option trades. It is achieved by an added focus on conversations and the inclusion of non
With the development of atomic energy application and research, hot laboratories are now being constructed in a number of countries. The present publication describes and discusses experience in several countries in designing equipment for these laboratories. The safe handling of highly radioactive substances is the main purpose of hot laboratory design and equipment. The manual aims at helping those persons, particularly in the developing countries, who plan to design and construct a new hot laboratory or modify an existing one. It does not deal in great detail with the engineering design of protective and handling equipment; these matters can be found in the comprehensive list of references. The manual itself covers only basic ideas and different approaches in the design of laboratory building, hot cells, shielded and glove boxes, fume cupboards, and handling and viewing equipment. Systems for transferring materials and main services are also discussed.
Aktacir, Mehmet Azmi; Bueyuekalaca, Orhan; Bulut, Huesamettin; Yilmaz, Tuncay
Outdoor design conditions are important parameters for energy efficiency of buildings. The result of incorrect selection of outdoor design conditions can be dramatic in view of comfort and energy consumption. In this study, the influence of different outdoor design conditions on air conditioning systems is investigated. For this purpose, cooling loads and capacities of air conditioning equipments for a sample building located in Adana, Turkey are calculated using different outdoor design conditions recommended by ASHRAE, the current design data used in Turkey and the daily maximum dry and wet bulb temperatures of July 21st, which is generally accepted as the design day. The cooling coil capacities obtained from the different outdoor design conditions considered in this study are compared with each other. The cost analysis of air conditioning systems is also performed. It is seen that the selection of outdoor design conditions is a very critical step in calculation of the building cooling loads and design capacities of air conditioning equipments
... 46 Shipping 4 2010-10-01 2010-10-01 false Design of equipment for cooking and heating. 130.220... Design of equipment for cooking and heating. (a) Doors on each cooking appliance must be provided with heavy-duty hinges and locking-devices to prevent accidental opening in heavy weather. (b) Each cooking...
Shibata, H.; Kato, M.
This paper deals with a new concept of anti-earthquake design of equipment and pipings in nuclear power plants. Usual anti-earthquake design of such items starts from the design basis ground motions, via floor responses and ends at the stress analysis of each structural element. However, the same type of equipment are used for plants under various site conditions. The ordinarily used method obliges the repetition of such design procedure on each plant. This new design method has been developed to avoid such time-consuming repetitions. (orig.)
Tollestrup, Christian; Eriksen, Kaare
Can distilled design methods for non-designers to user-driven innovation inform design education of Industrial Designers? In 2010 a project on employee driven innovation in the Hospital Sector with Aalborg University and Aalborg Hospital provided 35 participants from all over the hospital...... of potentials and problems to systematic ideation. This paper compares the use these methods in the two settings and especially the problem framing is problematic for both employees and students. For each method strengths and weakness in both situations are outlined. Finally it is concluded that the experiment...... of taking the tools made for employee-driven innovation back into the education stage without any change and without the full-facilitated support from the project setting shows that introducing tools without the mind-set is challenging the very value of these tools....
Roberts, Jess P; Fisher, Thomas R; Trowbridge, Matthew J; Bent, Christine
The business community has learned the value of design thinking as a way to innovate in addressing people's needs--and health systems could benefit enormously from doing the same. This paper lays out how design thinking applies to healthcare challenges and how systems might utilize this proven and accessible problem-solving process. We show how design thinking can foster new approaches to complex and persistent healthcare problems through human-centered research, collective and diverse teamwork and rapid prototyping. We introduce the core elements of design thinking for a healthcare audience and show how it can supplement current healthcare management, innovation and practice. Copyright © 2015 Elsevier Inc. All rights reserved.
Steffen, R.J.; Kurasch, D.H.; Hardin, R.T.; Schmitten, P.F.
In conjunction with the Spent Fuel Handling and Packaging Program (SFHPP) equipment has been designed, fabricated and successfully utilized to demonstrate the packaging and interim dry storage of spent LWR fuel. Surface and near surface storage configurations containing PWR fuel assemblies are currently on test and generating baseline data. Specific areas of hardware design focused upon include storage cell components and the support related equipment associated with encapsulation, leak testing, lag storage, and emplacement operations
Schjær-Jacobsen, Hans; Abou-Hayt, Imad; Ashworth, David
This paper describes how the Copenhagen University College of Engineering (IHK), in our continuing effort to innovate the engineering study programs, have introduced strong industrial design elements in the 210 ECTS Bachelor of Mechanical Engineering program as well as the 30 ECTS International...... Design Semester and the 10 ECTS Summer School in International Design and Development. The paper describes how implementation of novel industrial design subject areas requires the creation of new laboratory and workshop facilities in order to combine traditional engineering design disciplines...... with creative design as a driver of innovation. With a practical and problem based learning approach at IHK the students are asked to work closely together with companies to come up with engineering solutions that are sustainable from both an engineering and a design perspective....
This book explains reliability techniques with examples from electronics design for the benefit of engineers. It presents the application of de-rating, FMEA, overstress analyses and reliability improvement tests for designing reliable electronic equipment. Adequate information is provided for designing computerized reliability database system to support the application of the techniques by designers. Pedantic terms and the associated mathematics of reliability engineering discipline are excluded for the benefit of comprehensiveness and practical applications. This book offers excellent support
Zhu, Zhijuan; Zhou, Qi; Li, Bin; Visser, Steve
Research on numerical control (NC) equipment has been more and more abundant; however, there are few existing studies in the field of appearance design for NC equipments. This paper provided a method to generate new appearance design of NC equipments based on product identity (PI). For the purpose of providing guidelines to generate new concept of NC equipment design, this paper, therefore, took the DMG Company (a Germen NC equipment company) as a case, examined the total products of this company from two aspects: Product Image and Product Family. Task 1 was an evaluate task about the Product Image by using the semantic differential (SD) evaluation method; Task 2 was a study task about Product Family to find out features of the products and classify these features. During the Task 2, several features have been found out and summarized, and these features were classified into 3 different levels according to their frequency and importance. In the end, two appearance design samples have been generated based on the analysis above to prove the application of the research.
Buur, Jacob; Gudiksen, Sune Klok
Many companies see the need to rethink their ways of doing business, in particular under the pervasive influence of Internet business. Design can play a prominent role here, as a way of expanding from a linear, rational conception of business model development. But rather than proposing ‘design...... business models’ – for example in the form of pinball-like contraptions – encourage participants to play with hypotheses and experiment with scenarios as a way of innovating business models. In a sense this is ‘design thinking’ with hands and body....... thinking’ as an abstract approach, this paper shows how design materials (as used routinely in the design profession), when introduced in a business context can engage a cross-disciplinary circle of stakeholders and challenge them to reconsider their business assumptions. We will show how ‘tangible...
The book provides a snapshot of a hot topic – the systemic nature of innovation and its relevance to design – with a trifold perspective: the academic level – the literature on innovation studies and design is often neglected and a clear connection between the two topics taken for granted; the research level – collaborative models are currently considered great opportunities for transforming consumption, production and distribution of goods, but a clear scholarly discourse is still forming; the political level – the European Commission and the OECD are devoting much effort to understanding and measuring the impact of design in innovation processes and firms and a clear contribution would greatly support this path. Thus the book provides an informed, historical and nuanced perspective to the relationship between design and innovation to contribute to all three levels and to propose a point of view that goes beyond aesthetics and meanings.
Alden Rivers, Bethany; Armellini, Alejandro; Maxwell, Rachel; Allen, Sue; Durkin, Chris
Purpose—This paper proposes a theoretical framework to support the embedding of social innovation education in existing academic programmes.\\ud Design/methodology/approach—By adopting Conole et al.’s (2004) methodological approach to reviewing, mapping and modelling learning theory, this study addresses four research questions: 1) How can social innovation education be defined? 2) Which learning theories best support social innovation education? 3) How do such learning theories relate to exis...
Full text: The main activities of the Department for Nuclear Equipment High Technology Centre in 2008 were focused on the development of specialized systems using linear accelerators for medical applications, realized within the frame of the Innovative Economy Operational Program: · Calculations, simulations and design of accelerator structures and beam shaping devices · Design of a model of carrying structures · Building stands for carrying out critical component examinations and tests A new evolutionary algorithm has been implemented in a three-dimensional treatment planning system for intensity modulated radiotherapy (IMRT) planning optimization. A design for a multi leaf collimator, second model, was worked out. The Department received an Award for the Polkam TBI therapeutic table in the first edition of the '' Teraz-Polska '' national contest for the best Polish innovative product. Equipment manufactured by the High Technology Centre and especially for total body irradiation techniques was presented for the first time during the Biennial Meeting of the European Society for Therapeutic Radiology and Oncology in Goeteborg, Sweden. The second edition of the School of Medical Accelerator Physics organized in October 2008 was well received by medical physicists and physicians. (author)
Pavel, Nenad; Berg, Arild
To the extent previously claimed, concept exploration is not the key to product innovation. However, companies that are design-focused are twice as innovative as those that are not. To study design-driven innovation and its occurrence in design education, two case studies are conducted. The first is an example of design practice which includes…
A new CMS tracker is scheduled to become operational for the LHC Phase 2 upgrade in the early 2020's. tkLayout is a software package developed to create 3d models for the design of the CMS tracker and to evaluate its fundamental performance figures. The new tracker will have to cope with much higher luminosity conditions, resulting in increased track density, harsher radiation exposure and, especially, much higher data acquisition bandwidth, such that equipping the tracker with triggering capabilities is envisaged. The design of an innovative detector involves deciding on an architecture offering the best trade-off among many figures of merit, such as tracking resolution, power dissipation, bandwidth, cost and so on. Quantitatively evaluating these figures of merit as early as possible in the design phase is of capital importance and it is best done with the aid of software models. tkLayout is a flexible modeling tool: new performance estimates and support for different detector geometries can be quickly added, thanks to its modular structure. Besides, the software executes very quickly (about two minutes), so that many possible architectural variations can be rapidly modeled and compared, to help in the choice of a viable detector layout and then to optimize it. A tracker geometry is generated from simple configuration files, defining the module types, layout and materials. Support structures are automatically added and services routed to provide a realistic tracker description. The tracker geometries thus generated can be exported to the standard CMS simulation framework (CMSSW) for full Monte Carlo studies. tkLayout has proven essential in giving guidance to CMS in studying different detector layouts and exploring the feasibility of innovative solutions for tracking detectors, in terms of design, performance and projected costs. This tool has been one of the keys to making important design decisions for over five years now and has also enabled project engineers
Nair, B.R.; Bahorich, R.J.
The current design concept for the disposal of nuclear high level waste packages in a repository in salt is based on the emplacement of individual packages in vertical boreholes in the underground mine floor. A key requirement is that the waste packages be capable of being retrieved during the last 26 years of the 76-year repository operating period. The unique design considerations relating to the retrieval of waste packages emplaced in bedded salt are presented in this paper. The information is based on the experience developed during the design of vertical emplacement and retrieval equipment in support of the Sandia Defense High Level Waste experiments at the Waste Isolation Pilot Plant. Also included are the impact of retrievability on the design of the equipment, the special salt cutting technology that was developed for this application, and a description of the equipment
Tomico Plasencia, O.; Lu, Y.; Baha, S.E.; Lehto, P.; Hivikoski, T.; Roozenburg, N.F.M.; Chen, L.; Stappers, P.J.
This paper explores a designerly approach to open innovation initiation as start of the PhD research of the third author. More specifically, it presents the application of co-reflection sessions by designers in a healthcare open innovation project to initiate multi-stakeholder participation.
Nguyen Phuc; Nguyen Van Si; Le Tien Quan; Trinh Anh Tuan; Nguyen Manh Hung; Trinh Dinh Tuong
The main purposes of the project are the supporting to design and construction of the Portable Industrial X-Ray Equipment; with the accuracy ±2% of Output High Voltage 200 kV and Tube current 5 mA. The Equipment is composed of control unit, X-ray generator, and power cable, connection cable. X-ray generator is assembling construction X-ray tube, H.V transformer together with gas insulation (SF6) are sealed up in aluminum bucked cabinet, fan and heat-sink are mounted in the end of X-ray generator as cooling, SF6 is a gas electrical performance to H.V. Alarm lamp is used to warn, flashing, show generating X-ray. Control unit is box construction. Four printed circuit boards (PCB) and electronic device are mounted in it. All operating buttons switches and displays are equipped on the panel. We have completed to design and construct the Portable Industrial X-Ray Equipment; and have tested the electronic parameters of all test points and the main parameters of equipment (the accuracy ±2% of Output High Voltage 200 kV and Tube current 5 mA). We also have successful used the Portable Industrial X-Ray Equipment to evaluate the welds in industry. (author)
Yoshio Kamishima; Tai Asayama; Yukio Takahashi; Masanori Tashimo; Hideo Machida; Yomomi Otani; Yasuharu Chuman
The development of innovative nuclear plants where the energy in the future is carried out in Japan. The design method based on a risk benefit of having maintained mitigation of a risk and the improvement in economy is called for, in order to realize the national innovative nuclear plants. Main key technologies of the risk benefit structural design method are crack propagation evaluation technology and structural reliability evaluation technology. This research aims at pulling up these two technologies on an engineering practical use level. In this paper, requirements from the design of typical innovative nuclear plants and research plan are shown.(authors)
sociotechnical arrangement within the paradigm of open innovation. We explore how effectively technological platforms address emergent collaboration and innovation practices within and across organizations and to which extent existing technologies act as strategic catalysts of open innovation. We argue...... that in embracing wholeness and in treating technologies as inseparable constitutive parts of organizational architecture, we foster organizational and institutional collaboration and encourage innovative practices. The focus of the paper is on how the design of sociotechnical systems as wholes, that is systems...... that are concurrently acting as corporate websites, internal collaboration spaces, extranets and social media aggregators, actively promotes open innovation in practice. We close with a presentation of six cases that are illustrative of how such a system could be applicable within the open innovation paradigm, namely...
The French design and construction for electrical equipments of nuclear islands (RCC-E) deals with equipments of which the failure may have consequences on the safety of persons or appreciable effects on the availability of the power plant. This book presents the rules concerning (1) qualification procedure, (2) the design of functional units, (3) the installation (environmental conditions, protection rules), (4) the constituent elements of equipments, (5) the control and testing methods
Dr. Yen Hsu
Marketing should closely coordinate with product innovation. Not only will an effective connection of the marketing activity and design trigger product innovation in enterprises, it is a key factor to the product success in the market place. In practice, how to process product design so as to reach the goal of marketing during the innovation procedure? In the past, enterprises did have some concrete actions but empirical studies regarding the correlation model between marketing strategy and d...
This System Design Description (SDD) is for the Master Equipment List Phase I (MEL). It has been prepared following the WI-IC-CM-3-10, ''Software Practices,'' (Ref. 6). This SDD describes the internal design for implementation of the MEL Phase I
Hopkins, G.R.; Cheng, E.T.; Fisher, R.K.
The low activation fusion concept has been applied to the diagnostic equipment in a fusion reactor. The components where fabrication from low activation materials is feasible have been identified. Other systems where higher activation elements are required can have their activation reduced by design approaches which include shielding and operation only in low flux regions of the reactor. Some components will not operate in a high flux so activation is not a major concern. This low activation diagnostic equipment study completes a series of low activation studies where all the components in a fusion power reactor have now been evaluated. It is concluded that a completely low activation fusion reactor is feasible with all components meeting the functional requirements. This provides an environmentally benign energy source with a high confidence level in meeting safety criteria in operation, maintenance and waste disposal
Argonne National laboratory (ANL) is refurbishing the hot cell facility originally constructed with the EBR-II reactor. When refurbishment is complete, the facility win demonstrate the complete fuel cycle for current generation high burnup metallic fuel elements. These are sodium bonded, stainless steel clad fuel pins of U-Zr or U-Pu-Zr composition typical of the fuel type proposed for a future Integral Fast Reactor (IFR) design. To the extent possible, the process equipment is being built at full commercial scale, and the facility is being modified to incorporate current DOE facility design requirements and modem remote maintenance principles. The current regulatory and safety environment has affected the design of the fuel fabrication equipment, most of which will be described in greater detail in subsequent papers in this session
Li, Xiaolong; Zhao, Wu; Zheng, Yake; Wang, Rui; Wang, Chen
To improve customer satisfaction in innovative product design, a topology structure of customer requirements is established and an innovative product approach is proposed. The topology structure provides designers with reasonable guidance to capture the customer requirements comprehensively. With the aid of analytic hierarchy process (AHP), the importance of the customer requirements is evaluated. Quality function deployment (QFD) is used to translate customer requirements into product and process design demands and pick out the technical requirements which need urgent improvement. In this way, the product is developed in a more targeted way to satisfy the customers. the theory of innovative problems solving (TRIZ) is used to help designers to produce innovative solutions. Finally, a case study of automobile steering system is used to illustrate the application of the proposed approach.
Full Text Available To improve customer satisfaction in innovative product design, a topology structure of customer requirements is established and an innovative product approach is proposed. The topology structure provides designers with reasonable guidance to capture the customer requirements comprehensively. With the aid of analytic hierarchy process (AHP, the importance of the customer requirements is evaluated. Quality function deployment (QFD is used to translate customer requirements into product and process design demands and pick out the technical requirements which need urgent improvement. In this way, the product is developed in a more targeted way to satisfy the customers. the theory of innovative problems solving (TRIZ is used to help designers to produce innovative solutions. Finally, a case study of automobile steering system is used to illustrate the application of the proposed approach.
O'Hare, Jamie Alexander; McAloone, Tim C.
Eco-innovation is an approach that has the potential to deliver step change improvements in the environmental performance of products, but the uptake by industry to date has been disappointing. The paper presents a selective review of the academic literature, choosing examples of research that gi...... a flavour of the key trends and interesting topics that are emerging from the eco-innovation body of knowledge. We conclude by suggesting 10 areas where we see potential for the engineering design research community to contribute to the advancement of eco-innovation.......Eco-innovation is an approach that has the potential to deliver step change improvements in the environmental performance of products, but the uptake by industry to date has been disappointing. The paper presents a selective review of the academic literature, choosing examples of research that give...
C. Jason Mabry
Full Text Available This paper communicates the results of an architectural research project which sought innovative design strategies for achieving energy and resource efficiencies in water management systems traditionally used in single-family housing. It describes the engineering of an efficient, multifaceted, and fully integrated water management system for a domesticenvironment of 800 sq. ft., entirely powered by solar energy. The four innovations whose details are conveyed include the use of alternate materials for piping distribution and collection, the use of water in solar energy generation, the design of a building skin which capitalizes on water’s capacity to store heat as well as the design of a ecological groundscape which re-usesand filters waste water and rain water.Keywords: energy, plumbing, home design
Petersen, Anne Kristine; Gundersen, Peter Bukovica
In this article we explore the challenges of designing new, radical education formats from a design-based research perspective. The article opens with a discussion of central challenges in organisational innovation with particular emphasis on innovation in educational institutions prompted by new...... education reforms. The different roles and functions assumed by the design researcher are also discussed, and it is argued that the role of the project manager should be reconsidered as exceedingly crucial in successful implementation of reform-driven educational innovation. The article draws on empirical...... findings from a recent reform-driven innovation in the form of a MOOC (Massive Open Online Course), which offers courses to Danish primary and lower-secondary school teachers in need of further training. The findings discussed in the article indicate that radical education innovations may be adversely...
This standard is written to serve as a general standard for qualification of all types of safety systems equipment, mechanical and instrumentation as well as electrical. It also establishes principles and procedures to be followed in preparing specific safety systems equipment standards. Guidance for qualifying specific safety systems equipment may be found in various specific equipment qualification standards that are now available or are being prepared. It is required that safety systems equipment in nuclear power generating stations meet or exceed its performance requirements throughout its installed life. This is accomplished by a disciplined program of design qualification and quality assurance of design, production, installation, maintenance and surveillance. This standard is for the design qualification section of the program only. Design qualification is intended to demonstrate the capability of the equipment design to perform its safety function(s) over the expected range of normal, abnormal, design basis event, post design basis event, and in-service test conditions. Inherent to design qualification is the requirement for demonstration, within limitations afforded by established technical state-of-the-art, that in-service aging throughout the qualified life established for the equipment will not degrade safety systems equipment from its original design condition to the point where it cannot perform its required safety function(s), upon demand. The above requirement reflects the primary role of design qualification to provide reasonable assurance that design- and age-related common failure modes will not occur during performance of safety function(s) under postulated service conditions
The concept of inherent shutdown is emphasized in the approach to the design of innovative, small pool-type liquid-metal reactors (LMRs). This paper reports an evaluation of reactivity feedback uncertainties used in the analyses of anticipated transients without scram for innovative LMRs, and the associated impacts on safety margins and inherent shutdown success probabilities on unprotected loss-of-flow (LOF) events. It then assesses the ultimate importance of these uncertainties on LOF and transient overpower events in evolving metal and oxide innovative designs
The concept of ''inherent shutdown'' is emphasized in the approach to the design of innovative, small pool-type liquid metal reactors (LMRs). This paper reports an evaluation of reactivity feedback uncertainties used in the analyses of anticipated transients without scram (ATWS) for innovative LMRs, and the associated impacts on safety margins and inherent shutdown success probabilities on unprotected loss-of-flow (LOF) events. It then assesses the ultimate importance of these uncertainties on LOF and transient overpower (TOP) events in evolving metal and oxide innovative designs
Park, Y.S.; Park, C.O.
The nuclear design analysis requires time-consuming and erroneous model-input preparation, code run, output analysis and quality assurance process. To reduce human effort and improve design quality and productivity, Innovative Design Processor (IDP) is being developed. Two basic principles of IDP are the document-oriented design and the web-based design. The document-oriented design is that, if the designer writes a design document called active document and feeds it to a special program, the final document with complete analysis, table and plots is made automatically. The active documents can be written with ordinary HTML editors or created automatically on the web, which is another framework of IDP. Using the proper mix-up of server side and client side programming under the LAMP (Linux/Apache/MySQL/PHP) environment, the design process on the web is modeled as a design wizard style so that even a novice designer makes the design document easily. This automation using the IDP is now being implemented for all the reload design of Korea Standard Nuclear Power Plant (KSNP) type PWRs. The introduction of this process will allow large reduction in all reload design efforts of KSNP and provide a platform for design and R and D tasks of KNFC. (authors)
Full Text Available Innovation is an important aspect of contemporary business. Rapid change in guests' preferences and expectations significantly affect the restaurant industry. Meeting the diverse hospitality needs implies making innovative programs in all processes such as technical, technological as well as service oriented. Hospitality industry enters into the process of accelerated changes of modern equipment, updated technology, business strategies and hospitality management. The paper will discuss innovative offer design, molecular gastronomy, modern food presentation technique as well as authentic culinary products offer. By introducing such innovations, restaurants create the image of organisations following current trends as well as responding to the market requirements.
In considering the response of a nuclear reactor structure to seismic motions, one must take account of the implications of various levels of damage, short of impairment of safety, and definitely short of collapse, of the structure. Some structural elements of nuclear power plants must perforce remain elastic or nearly elastic in order to perform their allocated safety function. However, in many instances, a purely linear elastic analysis may be unreasonably conservative when one considers that even up to the near yield point range, there are nonlinearities of sufficient amount to reduce required design levels considerably. Moreover, limited yielding of a structure may reduce the response of equipment located in the structure below those levels of response that would be excited were the structure to remain elastic. Energy absorption in the inelastic range is most conveniently treated by use of the so-called 'ductility factor' introduced by the author for design of structures and equipment to resist explosion and blast forces. In general, for small excursions into the inelastic range, especially when the latter can be approximated by an elasto-plastic resistance curve, the design response spectrum is decreased by a simply determined factor that is related to the ductility factor. Many important parts of equipment of a nuclear power plant facility are attached to the principal parts of the structure and respond in a manner determined by the structural response as well as by the general ground motion to which the structure is subjected. This matter involves some difficulty in analysis, but appropriate calculational techniques and design methods are available. A suitable design simplification is one in which the response of the attachment is related to the modal responses of the structure. This equipment response is affected by the relative mass of the attachment and the structure
Blackwood, R L
The author presents a summary of proceedings of the First International Symposium on Innovative Mining Systems held at Massachusetts Institute of Technology, USA 4-5 November 1985, together with some comments on the conclusions and discussion throughout. The Symposium agenda included the following (i) Symposium intentions and expectations; (ii) International; (iii) Developments in safety; (iv) Overview of current major research and trends; (v) Panel discussion: Mechanisms for industrial and international collaboration; (vi) Closing remarks; (vii) Review of innovations: university programs; (viii) Review of selected mine operator programs and needs; Review of equipment innovations; capabilities and trends in areas of mining equipment and robotics; Concurrent sessions: operations and manufacturing. A series of workshops was also held, the titles of which were as follows: (i) Establishment of research network; (ii) Entry development-machine excavation; (iii) Sensing, monitoring, diagnostics, artificial intelligence; (iv) Remote control, automation, mining systems; (v) Computer aided design, simulation, system development; (vi) Surface mining; (vii) Rock breakage.
Judson, B.F.; Maillet, J.; O'Neill, G.L.; Tsitsichvili, J.; Tucoulat, D.
The purpose of the Prototypical Consolidation Demonstration Project (PCDP) is to develop and demonstrate the equipment system that will be used to consolidate the bulk of the spent nuclear fuel generated in the United States prior to its placement in a geological repository. The equipment must thus be capable of operating on a routine production basis over a long period of time with stringent requirements for safety, reliability, productivity and cost-effectiveness. Four phases are planned for the PCDP. Phase 1 is the Preliminary Design of generic consolidation equipment that could be installed at a Monitored Retrievable Storage (MRS) facility or in the Receiving ampersand Handling Facility at a geologic repository site. Phase 2 will be the Final Design and preparation of procurement packages for the equipment in a configuration capable of being installed and tested in a special enclosure within the TAN Hot Shop at DOE's Idaho National Engineering Laboratory. In Phase 3 the equipment will be fabricated and then tested with mock fuel elements in a contractor's facility. Finally, in Phase 4 the equipment will be moved to the TAN facility for demonstration operation with irradiated spent fuel elements. 55 figs., 15 tabs
NSF and other funders have supported the development of undergraduate STEM educational innovations over the past decades, only to see many yield limited uptake and impact beyond the grantee institutions. Numerous factors contribute to this complex problem, but one cause is likely insufficient incorporation of the understanding of how innovations propagate into project design. Following J.W. Dearing and colleagues, "dissemination" can be characterized by "push" approaches, which mainly emphasize one-to-many information sharing. In TUES/CCLI proposals, dissemination strategies have commonly taken the form of the "3 Ps" (presenting, publishing and posting) , with overall modest impact. Since the seminal work of Everett Rogers, however, "diffusion" of innovations has been understood as an inherently social process among potential adopters, which interacts with community norms and existing practices. Keys to diffusion include close understanding of the needs and context of the potential-adopter community and the development of "pull" within it, as well as support for implementation of innovations. Potential approaches to facilitating diffusion of innovations include a) using "lean start-up" methodologies (e.g., NSF's I-Corps-L program), in which explicit business-model hypotheses are tested through customer-discovery interviews, commonly leading to pivots where initial hypotheses are not confirmed, b) providing a range of potential commitment levels for adopters tailored to levels of support ("reverse Kickstarter model"), c) supporting decentralized communities of practice in which adaptations and tacit knowledge can readily be shared, d) encouraging crowd-sourcing of innovations, with an "architecture of participation" informed by successful open-source projects, and e) integrating innovations with discipline-based educational research, e.g., big-data approaches which allow A/B testing and analysis of clickstream data that reveal behaviors along a novice
Delistoian, Dmitri; Chirchor, Mihael
UOE pipe manufacturing process influence directly on pipeline resilience and operation capacity. At present most spreaded pipe manufacturing method is UOE. This method is based on cold forming. After each technological step appears a certain stress and strain level. For pipe stress strain study is designed and constructed special equipment that simulate entire technological process.UOE pipe equipment is dedicated for manufacturing of longitudinally submerged arc welded DN 400 (16 inch) steel pipe.
Minder, Bettina; Lassen, Astrid Heidemann
Design and innovation share the interest in creativity and development of novel solutions. However, literature does also provides sufficient material pointing to divergent views on the interrelation between two fields, where the focus lies on the distinction between two opposing discourses: one...... focusing on human-centeredness processes, the other favouring more linear process models (innovation management). Hence, design is increasingly often considered in innovation management because (not despite) the conflicts from different world-views (Brown, 2008, Boland and Collopy, 2004). Conceptual...... clarity becomes however more and more important, because the inclusion of design perspectives happen in situation, which require conscious shaping of innovation environment to harness complexity (Garud and Karnoe, 2013). This paper addresses the question of how the two concepts are understood...
Innovative engineering design shapes the development of novel technologies and is ethically as well as socially relevant, because it affects what kind of possibilities and consequences will arise. A major challenge in engineering design work on innovative technologies is the multitude of
Full Text Available Preparedness addresses the strategy in disaster management that allows the implementation of successful operational response immediately after a disaster. With speed as the main driver, product design for humanitarian aid purposes is a key factor of success in situations of high uncertainty and urgency. Within this context, a telecommunications container (TC has been designed that belongs to a group of containers that serve the purpose of immediate response to global disasters. The TC includes all the necessary equipment to establish a telecommunication centre in the destroyed area within the first 72 hours of humanitarian operations. The design focuses on defining the topology of the various parts of equipment by taking into consideration factors of serviceability, functionality, human-product interaction, universal design language, energy consumption, sustainability and the interrelationship with the other containers. The concept parametric design has been implemented with SolidWorks® CAD system.
Calabretta, G.; Gemser, G.; Wijnberg, N.M.; Hekkert, P.P.M.
To contain risks and increase the profitability of innovation efforts, firms frequently engage in joint innovation activities with external sources of knowledge, like design consultancies. Innovation literature has given limited consideration to the strategic role that design consultancies can play
Banuelos G, L. E.; Hernandez D, V. M.; Vega C, H. R.
From an old Nuclear Chicago power supply that was practically in the trash, was able to recover the 19 inches casing, rear connectors and the housing where the circuits were. From here all mechanical parts were cleaned and the electronic design was started to replace the original voltage and current functions of this equipment. The cards for the ±6, ±12 and ±24 voltages were designed, simulated and tested with circuitry that does not rely on specialized components or that is sold only by the equipment manufacturer. In the handling of the current by each voltage to operate, was possible to tie with the specifications of the manufacturers like Ortec or Canberra where a model of power supply gives a power of 160 Watts. Basic tests were performed to show that the behavior is very similar to commercial equipment; such as the full load regulation index and the noise level in the supply voltages. So our Nim-bin voltage source is viable for use in our institution laboratories. (Author)
is worked out under different ball screws, trapezoidal screw threads, worm and worm gears. To meet the requirement of tolerance in tubular-structure assembly, mechanisms for all motions are defined. The design of loading equipment is tested and assessed by experiments, and the result shows the design is highly qualified for its assembly.
Paloma, J. J.; Moraga, J. L.
From the beginning of its industrial activity 30 years ago, the Juzbado factory of Enusa Group has maintained a strong commitment to safety and technological innovation. As a result, we have development new equipment and constantly improving the existing ones, as well as the facilities of the factory in accordance with the internal procedures, with multidisciplinary design teams and review teams. (Author)
van Bruinessen, T.M.
Within the ship design industry, and in particular in the development of large, complex and innovative vessels experienced ship designers play an important role in organizing and structuring the design process. How this actually happens within projects that develop such large, complex and innovative vessels for a single client is not clear. This observation lead to a broad, initial research question as the starting point for further research. How are innovative, large and complex vessels deve...
Suzuki, Yasuharu; Nishizawa, Kazuo; Miyazaki, Yoshio; Miura, Takumi
The aseismatic design of electrical instruments is carried out according to IEEE Standard 344-1971 in the USA. In Japan also, the method of aseismatic design of electrical instruments has been investigated by the representatives of electric power companies and electric machine makers since 1972. In Hitachi Ltd., the statical method of confirming aseismatic property was established on the basis of the rigid design for electrical instruments. It is convenient to examine the aseismatic property of electrical equipments by classifying them into control and switch boards, electrical appliances, equipments and circuits. It is possible to use the static method treating earthquake force as static load by avoiding resonance with the electrical equipments which have the higher natural frequency than that of buildings. The purposes of the vibration test are to prove the validity of the theoretical analysis, to clarify the vibration characteristics, and to confirm the maintenance of functions and the strength of the equipments. The vibration tests of control boards, the switch boards of enclosed type, motor control centers, the racks for instrumentation, storage batteries and electrical appliances are explained. Moreover, the vibration analysis with a computer according to finite element method is described. (Kako, I.)
Karlangach A. P.
Full Text Available The author proposes a method to design electronic equipment based on functional-node design method that involves the use of 2D- and 3D- models mechanical structures for electronic equipment as a way to reduce development time and errors when creating design documentation for electronic equipment. At present, most areas of science and technology are computerized, more problems in designing electronic equipment are dealt with using computer-aided design (CAD and Computer-aided manufacturing (CAM to reduce the time required for development and manufacturing of electronic equipment. Development of design documentation also requires a more effective approach, because the less the time for development of the design documentation is, the faster the developed device will go into production. The aim of the study is to develop a method of designing electronic equipment using 2D and 3D models of standard mechanical structures for electronic equipment using Internet resources. Based on the presented methods is an example of designing a device from standard bearing structures. Compared with traditional technology, the method of designing electronic equipment using standard parts has the following advantages: - reduces time and improves quality of development through the use of existing design documentation; - accelerates the implementation and introducing into production processes; - increases unification of design solutions.
Manuela Aguirre Ulloa
Full Text Available Adapted from a review on the same book published by The Design Observer Group on April 4th, 2014. You can access the original publication online at http://designobserver.com/feature/design-for-care/38382/ Peter Jones´ recently published book represents a timely and comprehensive view of the value design brings to healthcare innovation. The book uses an empathic user story that conveys emotions and life to a structure that embraces the different meanings of Design for Care: Spanning from caring at the personal level to large-scale caring systems. The author has a main objective for each of its three main target audiences: Designers, companies and healthcare teams. Firstly, it allows designers to understand healthcare in a holistic and patient-centered way, breaking down specialized silos. Secondly, it shows how to design better care experiences across care continuums. Consequently, for companies serving the healthcare sector, the book presents how to humanize information technology (IT and services and meet the needs of health seekers. Finally, the book aims to inform healthcare teams (clinical practitioners and administrators the value design brings in research, co-creation and implementation of user and organizational experiences. It also proposes that healthcare teams learn and adopt design and systems thinking techniques so their innovation processes can be more participatory, holistic and user-centered.
Innovative engineering design shapes the development of novel technologies and is ethically as well as socially relevant, because it affects what kind of possibilities and consequences will arise. A major challenge in engineering design work on innovative technologies is the multitude of uncertainties in the form of known unknowns, unknown unknowns, complexities, and ambiguities. The evaluation and generation of design concepts are general and essential parts of the design process in which va...
The manual has been prepared for use by research personnel involved in experiments at the Lawrence Berkeley Laboratory. It contains rules and procedures for the design, test, installation, and operation of hazardous research equipment. Sect. I contains such information as responsibility of experimenters for safety, descriptions of the various Laboratory safety organizations, and enumeration of various services available to experimenters at the Laboratory. Sect. II describes specific rules for the setup and operation of experimental equipment at the Laboratory. Sect. III gives detailed design criteria and procedures for equipment frequently encountered in the high energy physics laboratory
The author describes the ideas and practical method for need analysis, system function dividing, code design, program design and network disposition of equipment purchase management system of nuclear power plant during building, from the view of engineering investment control, schedule control and quality control
Ouden, den P.H.
Innovation Design presents an approach to designing shared value for businesses, non-profit organizations, end-users and society. The societal and economic challenges we are currently facing - such as the aging population, energy scarcity and environmental issues - are not just threats but are also
Situmorang, Johnny; Tjahjono, H.; Santosa, A. Z.; Tjahjani, S.DT.; Ismu, P.H; Haryanto, D.; Mulyanto, D.; Kusmono, S
The equipment for reliability testing of cable of protection system has been designed as a a furnace with the electric heater have a 4 kW power, and need time 10 minute to reach the designed maximum temperature 3000C. The dimension of furnace is 800 mm diameter and 2000 mm length is isolated use rockwool isolator and coated by aluminium. For the designed maximum temperature the surface temperature is 78 0c. Assemble of specimens is arranged horizontally in the furnace. The failure criteria will be defined based on the behaviour of the load circuit in each line of cable specimens
Jon Carmack; Kemal Pasamehmetoglu
This document provides presentation and general analysis of innovative design concepts submitted to the FCRD Advanced Fuels Campaign by nine national laboratory teams as part of the Innovative Transmutation Fuels Concepts Call for Proposals issued on October 15, 2009 (Appendix A). Twenty one whitepapers were received and evaluated by an independent technical review committee.
Le Masson, Pascal; Hatchuel, Armand
This textbook presents the core of recent advances in design theory and its implications for design methods and design organization. Providing a unified perspective on different design methods and approaches, from the most classic (systematic design) to the most advanced (C-K theory), it offers a unique and integrated presentation of traditional and contemporary theories in the field. Examining the principles of each theory, this guide utilizes numerous real life industrial applications, with clear links to engineering design, industrial design, management, economics, psychology and creativity. Containing a section of exams with detailed answers, it is useful for courses in design theory, engineering design and advanced innovation management. "Students and professors, practitioners and researchers in diverse disciplines, interested in design, will find in this book a rich and vital source for studying fundamental design methods and tools as well as the most advanced design theories that work in practice". Pro...
Rüth, Ulrich; Holch, Astrid
Designing and equipping a play therapy room as a differentiated tool in a psychodynamic approach to child psychotherapy is seldom discussed. This article sketches out the equipment and furnishing of a play therapy room to be used for mentalization-based psychodynamic psychotherapy and gives examples of the use of such a room in practice.
Chakravarthy, Battula Kalyana
The book provides an in-depth knowledge on how a product is designed and developed by Product Designers. This has been achieved through a case study of one product – the Post Box. This product was chosen for the study primarily due to its simple and non-technical nature as that would make it easy for the readers to comprehend the design process. At the same time the Post Box posed all the challenges a designer would face while creating a new product. Through a step by step process the book gradually takes the reader through the design and development journey – right from understanding the product, identifying the user need through market research, comprehending client’s brief, generating product ideas and concepts to development of prototype, manufacturing and final performance of the product. The book illustrates the stages in the design process that lead to innovation which is applicable to all types of products. To make the book more stimulating, interesting facts, figures and pictures on related iss...
Ciriello, Raffaele Fabio; Richter, Alexander; Schwabe, Gerhard
As ever more companies encourage their employees to realize innovations, a surplus of ideas that exceeds the available resources to implement them has become reality in many organizations. With this paper, we follow recent calls for designing IT-supported, comprehensive, multi-attributive idea screening throughout the whole innovation cycle. Our Idea Screening Framework is grounded in literature and empirical data we collected from a two-year field study in a multinational European banking so...
John J Orloff
Full Text Available Pharmaceutical innovation is increasingly risky, costly and at times inefficient, which has led to a decline in industry productivity. Despite the increased investment in R&D by the industry, the number of new molecular entities achieving marketing authorization is not increasing. Novel approaches to clinical development and trial design could have a key role in overcoming some of these challenges by improving efficiency and reducing attrition rates. The effectiveness of clinical development can be improved by adopting a more integrated model that increases flexibility and maximizes the use of accumulated knowledge. Central to this model of drug development are novel tools, including modelling and simulation, Bayesian methodologies, and adaptive designs, such as seamless adaptive designs and sample-size re-estimation methods. Applications of these methodologies to early- and late-stage drug development are described with some specific examples, along with advantages, challenges, and barriers to implementation. Because they are so flexible, these new trial designs require significant statistical analyses, simulations and logistical considerations to verify their operating characteristics, and therefore tend to require more time for the planning and protocol development phase. Greater awareness of the distinct advantages of innovative designs by regulators and sponsors are crucial to increasing the adoption of these modern tools.
This report documents the completion of the formal design review for modifications to the Rotary Mode Core Sampling (RMCS) safety class equipment. These modifications are intended to support core sampling operations in waste tanks requiring flammable gas controls. The objective of this review was to approve the Engineering Change Notices affecting safety class equipment used in the RMCS system. The conclusion reached by the review committee was that these changes are acceptable
This report documents the completion of the formal design review for modifications to the Rotary Mode Core Sampling (RMCS) safety class equipment. These modifications are intended to support core sampling operations in waste tanks requiring flammable gas controls. The objective of this review was to approve the Engineering Change Notices affecting safety class equipment used in the RMCS system. The conclusion reached by the review committee was that these changes are acceptable.
Lu, Y.; Baha, S.E.; Hsieh, P.H.
This paper explores a design case study in an industrial design classroom in which actors with diverse expertise were involved for the creation of Product Service System (PSS) innovation opportunities in societal contexts. By engaging diverse experts from different fields, the classroom was turned
Kong Jinsong; Guo Weiqun; Lu Jingbin
The advantage and disadvantage of radioactive liquid waste treatment technology are analyzed in this paper. The experimental disposal equipment for radioactive liquid waste with complicated sources is designed by combining the far infrared calcification technology with evaporation technology. It has advantages of low energy consuming and high decontamination efficiency. The frothy and dirt appear rarely in this equipment. (authors)
Pajewski, Lara; Manacorda, Guido; Persico, Raffaele
This work aims at presenting the ongoing research activities carried out in Working Group 1 'Novel GPR instrumentation' of the COST (European COoperation in Science and Technology) Action TU1208 'Civil Engineering Applications of Ground Penetrating Radar' (www.GPRadar.eu). The principal goal of the COST Action TU1208 is to exchange and increase scientific-technical knowledge and experience of GPR techniques in civil engineering, simultaneously promoting throughout Europe the effective use of this safe and non-destructive technique in the monitoring of infrastructures and structures. Working Group 1 (WG1) of the Action focuses on the development of innovative GPR equipment dedicated for civil engineering applications. It includes three Projects. Project 1.1 is focused on the 'Design, realisation and optimisation of innovative GPR equipment for the monitoring of critical transport infrastructures and buildings, and for the sensing of underground utilities and voids.' Project 1.2 is concerned with the 'Development and definition of advanced testing, calibration and stability procedures and protocols, for GPR equipment.' Project 1.3 deals with the 'Design, modelling and optimisation of GPR antennas.' During the first year of the Action, WG1 Members coordinated between themselves to address the state of the art and open problems in the scientific fields identified by the above-mentioned Projects [1, 2]. In carrying our this work, the WG1 strongly benefited from the participation of IDS Ingegneria dei Sistemi, one of the biggest GPR manufacturers, as well as from the contribution of external experts as David J. Daniels and Erica Utsi, sharing with the Action Members their wide experience on GPR technology and methodology (First General Meeting, July 2013). The synergy with WG2 and WG4 of the Action was useful for a deep understanding of the problems, merits and limits of available GPR equipment, as well as to discuss how to quantify the reliability of GPR results. An
Jørgensen, Ulrik; Lindegaard, Hanne; Rosenqvist, Tanja Schultz
In this paper we share and analyze our experiences staging a co-design process in which we through different interventions engage important actors in designing. Our experiences are taking from an innovation and research project about user-involvement in textile design processes. As the project...... in our project’s agenda by going through the different stages of translation. The paper is finalized with reflections on the difficulties in engaging actors in a co-design process and transporting results into the existing framed context of design and architectural work....... related to translating and transporting the results of these different events due to the institutional and professional framing of projects and design processes. We are analyzing these through an actor network approach and use the translation term to describe how the participants slowly became engaged...
Monteiro, Jonathan K.R.; Farias, Marcos S.; Santos, Isaac J.A. Luquetti; Monteiro, Beany G.
Technology plays an important role in modern medical centers, making healthcare increasingly complex, relying on complex technical equipment. This technical complexity is particularly noticeable in the nuclear medicine. Poorly design human-system interfaces can increase the risks for human error. The human-centered approach emphasizes the development of the equipment with a deep understanding of the users activities, current work practices, needs and abilities of the users. An important concept of human-centered design is that the ease-of-use of the equipment can be ensured only if users are actively incorporated in all phases of the life cycle of design process. Representative groups of users are exposed to the equipment at various stages in development, in a variety of testing, evaluation and interviewing situations. The users feedback obtained is then used to refine the design, with the result serving as input to the next interaction of design process. The limits of the approach are that the users cannot address any particular future needs without prior experience or knowledge about the equipment operation. The aim of this paper is to present a methodological framework that contributes to the design of the human-system interfaces, through an approach related to the users and their activities. A case study is described in which the methodological framework is being applied in development of new human-system interfaces of the thyroid uptake system. (author)
Full Text Available Design of blasting parameters plays an important role in the optimization of mining cost as well as cost of subsequent processing of ore. Drilling and handling costs are the major mining cost. This work presents an indirect optimization model for mining cost through optimization of blasting parameters for a particular set of drilling and loading equipment.
High levels of gamma radiation are known to cause degradation in a variety of materials and components. When designing systems to operate in a high radiation environment, special precautions and procedures should be followed. This report (1) outlines steps that should be followed in designing equipment and (2) explains the general effects of radiation on various engineering materials and components. Much information exists in the literature on radiation effects upon materials. However, very little information is available to give the designer a step-by-step process for designing systems that will be subject to high levels of gamma radiation, such as those found in a nuclear fuel reprocessing facility. In this report, many radiation effect references are relied upon to aid in the design of components and systems. 11 refs., 4 tabs
Ma, Menglin; Wang, Chengqiang; Deng, Hai
According to the frequency configuration requirements of the vibration of railway under-chassis-equipment, the three- dimension stiffness of the suspension elements of under-chassis-equipment is designed based on the static principle and dynamics principle. The design results of the concrete engineering case show that, compared with the design method based on the static principle, the three- dimension stiffness of the suspension elements designed by the dynamic principle design method is more uniform. The frequency and decoupling degree analysis show that the calculation frequency of under-chassis-equipment under the two design methods is basically the same as the predetermined frequency. Compared with the design method based on the static principle, the design method based on the dynamic principle is adopted. The decoupling degree can be kept high, and the coupling vibration of the corresponding vibration mode can be reduced effectively, which can effectively reduce the fatigue damage of the key parts of the hanging element.
Guillaume Marrel; Magali Nonjon
The introduction of digital equipment is undoubtedly a technological and organizational innovation in a Local Plan for Economic Insertion. However, the actors of this structure qualify this equipment as a social innovation. Why do they use this qualification? This article is based on a monographic investigation. Can it be considered as a “social innovation for competition”? The observed differences, about the polysemy of term “social”, between the justification of practices and the academic c...
Sharp, R.; Pater, L.
The nuclear power industry has many demands for equipment tolerant to the damaging effects of radiation. The wide variety of applications, including components handling, tooling, monitoring and communications, means that a systematic evaluation of the effects of radiation on materials and components used for equipment in radioactive facilities is often required. This paper describes the various effects of radiation on equipment, and discusses how to manage them when using and designing equipment. (Author)
Huang, Yu-Che; Huang, Tai-Shen
This research is about the analysis and design of the user in a wheelchair use posture can be changed. So user can through different sitting posture changes to provide different needs, so the folding design patents for the existing data collection and classification, through the analysis of advantages and disadvantages, further to find the innovative design approach. Finally through the multi linkage mechanism system, change the seat, handlebars and rear position, provide different posture context. In order to reduce the cost, this study is designed to integrate the innovation input mechanism, multi linkage system, through the construction of 10 joints and degrees of freedom of the bicycle frame. Then use 3D software to design of bicycle the size of the frame of innovation, through the three-dimensional CAD model to simulate the mechanism between movement and interference, and to evaluate the 3D The virtual prototype can meet the requirement. It will also enable CAE to analyze and determine the strength and the safety of the bicycle frame structure of ANSYS11.0 stress. Finally, we have integrated design through CAID to make a product appearance, the focus of research is mainly a study of CAD, CAE, CAID integration the production and the completion of a prototype.
Pellis, Neal R.
The challenge of human space exploration places demands on technology that push concepts and development to the leading edge. In biotechnology and biomedical equipment development, NASA science has been the seed for numerous innovations, many of which are in the commercial arena. The biotechnology effort has led to rational drug design, analytical equipment, and cell culture and tissue engineering strategies. Biomedical research and development has resulted in medical devices that enable diagnosis and treatment advances. NASA Biomedical developments are exemplified in the new laser light scattering analysis for cataracts, the axial flow left ventricular-assist device, non contact electrocardiography, and the guidance system for LASIK surgery. Many more developments are in progress. NASA will continue to advance technologies, incorporating new approaches from basic and applied research, nanotechnology, computational modeling, and database analyses.
Ye Qizhen; Yang Lanhe
This article mainly describes the self-reliance and innovation of Qinshan nuclear power project of phase II, in-between it contains new reactor core design, as well as related experimental and calculation analysis, especially for new reactor design produced fluid-induced vibration model test, theoretical analysis and testing in-built reactor; aiming at two-loop NSSS a series improvement made for safety systems and related safety analysis to enhance their reliability and redundancy; according to specialty of two-loop NSSS an optimization made for NPP parameters and design of related equipments, for the purpose to make the output of NPP maximal; design of main reactor building and T-G building also improved according to characteristics of two-loop NSSS and site conditions. CRDM and refueling machine are researched and manufactured on base of self-reliance, their performance are better than design requirements, large portion of key equipments are localized through different way. In construction first time realized the integrated erection of containment dome. During the commissioning non-nuclear steam driving of T-G set, as well as 500 kV high voltage rising using emergent diesel generator, etc. are carried out.In period of operation still continuous innovation and improvement are made, so that to keep the good record of operation. (authors)
Andreoni, Giuseppe; Colombo, Barbara
During the past two decades incredible progress has been achieved in the instruments and devices used in the biomedical field. This progress stems from continuous scientific research that has taken advantage of many findings and advances in technology made available by universities and industry. Innovation is the key word, and in this context legal protection and intellectual property rights (IPR) are of crucial importance. This book provides students and practitioners with the fundamentals for designing biomedical devices and explains basic design principles. Furthermore, as an aid to the dev
Full Text Available This paper provides key results from an exploratory research study aimed at understanding the current landscape in small- and medium-sized enterprises (SMEs in South Africa with regard to their appetite for, and use of, open innovation. The survey, which was conducted within a contained group of SMEs that belong to business network groups on LinkedIn, explored the current use and perception of open innovation. It was found that collaboration is the approach most preferred by the SMEs surveyed, with customers and suppliers as their preferred innovation partners. Based on the findings of the survey, this paper proposes 25 design requirements, grouped into five functional categories, for an open innovation approach. The design requirements have been developed as a primer to a more complete open innovation approach for SMEs.
Østergaard, Rina; Sorensen, Elsebeth Korsgaard
Abstract This paper sets out on a reflective journey to investigate, theoretically, the potential of a marriage between Networked Learning (NL) and Design Based Research (DBR) (Barab & Squire, 2004) in a creative and innovative pedagogical practice for welfare professionals. With reference...... the entities of a model, which integrate the above mentioned relationships in learning designs. The suggested networked model offers possibilities of innovative learning in further educations. At the same time – in parallel – the suggested networked model offers possibilities of data generation to be used...... help and qualify the development of innovative DBR and NL designs directed towards the future. Assuming the views outlined and promoted in this paper, the authors claim that researchers in the field as well as welfare professionals in pedagogical, social and health areas, must display creative...
Amato, Andrea; Gallisto, Maurizio; Maccari, Augusto; Paganelli, Mauro; Compare, Michele; Zio, Enrico
Concentrating Solar Power (CSP) plants are a promising technology of renewable energy production, as witnessed by the increasing public and private investments during the last decade. The assessment of the associated risks of business interruption (loss of production) and loss of assets due to the occurrence of undesired internal or external events, such as failures of components, unfavorable environmental conditions, etc., brings added values by informing design modifications and contributing to production assurance, for rational Company investments in these environmentally sustainable power plants. This work presents and applies a methodology for assessing the risks associated to a CSP of innovative design. The methodology is derived from traditional system risk analysis, specifically focused only on the economic consequences of the internal events of failure behavior of components. The innovation in the design considered is particularly aimed at augmenting the CSP intrinsic capability of being equipped with thermal storage systems by the introduction of a molten salt mixture as heat transfer fluid. This technology presents evident advantages in terms of system simplification and reduction of production costs but on the other hand introduces a risk factor with regards to the solidification of the salt mixture that occurs at about 240 C. (author)
Uchiyama, Yuichi; Takayanagi, Masaaki; Moriyama, Takeo; Mizuno, Sadao
The social requirements for the safety of nuclear power stations are very severe, and especially in Japan where earthquakes occur frequently, the safety against earthquakes is regarded as an important matter. The numerous machinery and equipments composing nuclear power plants have largely different roles in the safety, accordingly it is important to maintain effectively the safety as a whole. The design is carried out by classifying buildings, machinery and equipments, pipings and electric appliances according to the importance, and so that the aseismatic property corresponding to the importance is given to each. In most cases, the aseismatic design is carried out with computing codes, but it is necessary to forward the design by proving the propriety of analysis models and calculated results. Efforts are exerted in Hitachi Ltd. to improve the accuracy of the aseismatic analysis by carrying out basic experiment, the demonstration test in actual plants and the study on analytical method as many as possible. The measurement of the vibration of actual pipings in order to confirm the supporting conditions, the comparison of multi-input analysis and SRSS method for piping analysis, and the vibration tests of a model containment vessel and a fuel assembly were carried out, and the results are reported in this paper. It is important to improve the accuracy of earthquake response analysis further. (Kako, I.)
A systematic review of the design and operations of the core sampling trucks was commissioned by Characterization Equipment Engineering of the Westinghouse Hanford Company in October 1995. The review team reviewed the design documents, specifications, operating procedure, training manuals and safety analysis reports. The review process, findings and corrective actions are summarized in this supporting document
The paper concludes that the design-based innovation paradigm is increasingly important within the manufacturing industry, but that its benefit can only be maximized if it is integrated with the other three value-creating approaches to innovation.
Fernández-Mesa, Ana Isabel; ALEGRE VIDAL, JOAQUIN; CHIVA GOMEZ, RICARDO; Gutiérrez Gracia, Antonio
[EN] Purpose The aim of this paper is to present design management as a dynamic capability and to analyze its mediating role between organizational learning capability and product innovation performance in small and medium enterprises (SMEs). Design/methodology/approach Structural equation modeling is used to test the research hypotheses based on data from the Italian and Spanish ceramic tile industries. The data are derived from the responses of 182 companies (50 percent of the targ...
Ozaltin, Nur Ozge; Besterfield-Sacre, Mary; Clark, Renee M.
Learning how to design innovatively is a critical process skill for undergraduate engineers in the 21st century. To this end, our paper discusses the development and validation of a Bayesian network decision support tool that can be used by engineering educators to make recommendations that positively impact the innovativeness of product designs.…
Petrovic, B.; Carelli, M.; Greenspan, E.; Matsumoto, H.; Padovani, E.; Ganda, F.
The International Reactor Innovative and Secure (IRIS) is being developed by an international consortium of industry, laboratory, university and utility establishments, led by Westinghouse. The IRIS design addresses key requirements associated with advanced reactors, including improved safety, enhanced proliferation resistance, competitive electricity production cost, and improved waste management. IRIS is a modular, small/medium size (335 MWe) PWR with an integral vessel configuration. The objective has been to base its design on proven LWR technology, so that no new technology development is needed and near-term deployment is possible, yet at the same time to introduce innovative features making it attractive when compared to present PWRs. These opposing requirements resulted in an evolutionary approach to fuel and core design, balancing new features against the need to avoid extensive testing and demonstration programmes. (author)
Currently there are no guidelines within the Manual on Uniform Traffic Control Devices (MUTCD) on construction phasing and maintenance of traffic (MOT) for retrofit construction and maintenance projects involving innovative geometric designs. The res...
Full Text Available Due to the current advances in Information and Communication Technologies and consumers’ increasing interest in entertaining and interactive retail environments, the sector of retailing is forced to pursuit innovation to maintain existing consumers and attract new ones. Especially the use of virtual reality techniques offers tools for supporting the design of innovative systems capable of enhancing this process. The aim of this paper is to integrate the consumers’ experience in the development of innovation process for retailing. In particular, our findings highlight how the immersive technologies can be an efficient tool for pushing innovation in retailing. Therefore, the paper provides important issues for scholars and practitioners.
Kim, Ki Ho; Kim, Sung Hyun; Yu, Seung Nam; Lee, Jong Kwang; Park, Byung Suk; Han, Jong Hui; Cho, Il Je; Lee, Han Soo
Process equipment for pyroprocessing are being developed at KAERI (Korea Atomic Energy Research Institute). Those equipment should be operated and maintained in a fully remote manner in the argon gas filled cell of PRIDE (PyRoprocess Integrated inactive DEmonstration facility) at KAERI because direct human access to the in-cell is not possible during an operation due to the high toxicity of the argon gas. To make such process equipment remotely operable and maintainable, their design developments have been tested and evaluated in a simulator before they are constructed. A simulator as a means of evaluating the remote operability and maintainability of the design models of process equipment for pyroprocessing is described, and results of the design models tested and evaluated in a simulator are presented
Doman, D.R.; Barker, R.E.
Fourteen key areas relating to facilities and equipment for handling radioactive materials involved in examination, reprocessing, fusion fuel handling and remote maintenance have been defined and writing groups established to prepare design guides for each areas. The guides will give guidance applicable to design, construction, operation, maintenance and safety, together with examples and checklists. Each guide will be reviewed by an independent review group. The guides are expected to be compiled and published as a single document
Norayr Oganesovich Bludyan
Full Text Available The analysis of international experience in application of requirements for the taxi vehicles design and equipment. The approaches to improvement of cabbing have been defined by determination of requirements for taxi vehicles.
Full Text Available Though, in the automotive industry, technology is considered as a source of innovation and development, emerging change in consumer perception has brought industry focus on design. Evolution of this industry is closely related to the convergence of technology and design. In such context, implication of design driven innovation strategy in the automotive industry has potential to be explored and to create sustained competitive advantage through balancing customers’ need, technological opportunities and product meaning. The aim of this paper is to give a holistic view of design driven innovation as a differentiation strategy in the automotive industry and its implication for strategic management through some relevant research reviews and empirical information. On the contrary, this research lacks detailed description on industry practice to provide greater breadth, since it attempts to correlate the strategic concept of design with the dynamic capability of a firm in that particular industry.
Mulder, W.; Basten, Robertus Johannes Ida; Jauregui Becker, Juan Manuel; Blok, Jeroen; Hoekstra, Sipke; Kokkeler, Frans; Marjanovic, Dorian; Storga, Mario; Pavkovic, Neven; Bojcetic, Nenad
This paper presents a leaflet with design-for-maintenance guidelines. It aims at supporting developers of industrial equipment in their design-for-maintenance practices. The use of this leaflet should lead to increased attention for design-for-maintenance aspects and to improve idea generation. The
Mariano Norzagaray Campos
Full Text Available Geochemical exploration equipments to explore the contaminants and structures geological in the subsoil come from abroad are expensive and sometimes parts for replacement are not available in the market. So it is necessary design apparatus that meet cover these needs. To the monitoring of variations in salinity there is semi-automatic equipment, but it always has difficult to manage. However, is not equipment for the indirect study of salinity in the subsoil. In this work was design equipment for measurement the apparent resistivity in the subsoil, at same time allow know the salinity, as well as the detection of any pollutant in groundwater. For make it, was selected a design of earthing systems, with electronic hardware which were jointed for apply to subsoil a direct current (DC through an array dipole-dipole and vertical electric sounding, with brass and stainless steel electrodes. In the earthing systems the electrodes were collocated in the equidistant line between the detectors of potential and current. A geometric factor (K, that depend on theelectrodes distance and direct current (I injected in the electrodes A and B, was used for measure the potential difference between the electrodes M and N; after was calculate the resistivity point to point for obtain a subsoil tomography geoelectrical. The equipment was calibrated with minimum error (rms < 2% whit respect to curves obtained in similar commercial equipment. On this situation, in this work was modernized and automated an equipment to determine thesalinity of the subsoil. The instrument was tasted in the micro basin Texcoco, State of Mexico, to define the environment geometry formed by alluvial or lake sediments from igneous rocks (andesites, rhyolites and tuffs vitreous or “tepetates” which by its mineralogical composition allowed to the lateral resistivity be associate with free components trace from the aquifer: Cd, Cu, Cr, Co, Ni, Pb or Zn and others. This method constitutes
This book constitutes the proceedings of two conferences: The 5th International Conference on ArtsIT, Interactivity and Game Creation (ArtsIT 2016) and the First International Conference on Design, Learning and Innovation (DLI 2016). ArtsIT is reflecting trends in the expanding field of digital art......, interactive art, and how game creation is considered an art form. The decision was made to augment the title of ArtsIT to be in future known as “The International Conference on Interactivity, Game Creation, Design, Learning, and Innovation”. The event was hosted in Esbjerg, Denmark in May 2016 and attracted...
Ford, Cristi; McNally, Darragh; Ford, Kate
This paper discusses the design-based research approach used by the Center for Innovation in Learning and Student Success (CILSS) at the University of Maryland, University College (UMUC). CILSS is a laboratory for conducting applied research that focuses on continuous improvements to the university's instruction of curriculum, learning models, and…
Hu Jinming; Wang Chao; Peng Jinhui; Zhang Libo
In order to solve problems by artificial feeding mode with low work efficiency, large intensity manual labor and environmental pollution in domestic uranium concentrate purification process, the design scheme of automatic feeding device was set up, including work flow sheet, composition of automatic equipment and operation. By application of automatic feeding equipment, the feeding speed can be greatly increased, labor force can be reduced, and harm to workman health can be decreased. (authors)
Cui Yong Min; Ren Xin Guang
The paper solves the increasingly deteriorate environmental problems by positively exploring how to utilize and develop eco-packaging design reasonably. The paper explores an effective method that combines eco-packaging and environmental protection materials, hoping to define the sustainable development road of packaging design. The paper is centered on the design application of eco-packaging and environmental protection materials, applies and analyzes the method to obtain innovative design r...
This guide presents an acceptable method for developing two horizontal and one vertical floor design response spectra at various floor or other equipment-support locations from the time-history motions resulting from the dynamic analysis of the supporting structure. These floor design response spectra are used in the dynamic analysis of systems or equipment supported at various locations of the supporting structure. Consulation has been provided by the Advisory Committee on Reactor Safeguards
Swannack, D.L.; Schmoker, D.S.
This paper summarizes results obtained in use of remotely-operated nondestructive testing (NDT) equipment for inspection of reactor-system components. Experience obtained in operating the Fast Flux Test Facility (FFTF) has provided a basis for field verification of remote NDT equipment designs and has suggested development improvements. Remote Viewing and data gathering systems used include periscopes, borescopes, fiberscopes, hybrid borescopes/fiberscopes, and closed circuit television. A summary of design consideration for inspection equipment and power plant design is presented to achieve improved equipment operation and reduction of plant maintenance downtime
Fujisawa, Morio; Nitta, Kazuhiko; Morita, Yasuhiro; Nakada, Eiju
This report describes the result of Conceptual Design of the Alcohol Waste Treatment Equipment. The experimental fast Reactor, JOYO, saves the radioactive alcohol waste at storage tank. As this alcohol waste is not able to treat with existing equipment, it is stored about 5 m 3 . And the amount of this is increasing every year. So it is necessary to treat the alcohol waste by chemical resolution for example. On account of this, the investigative test about filtration and dialyzer, and conceptual design about catalyst oxidation process, which is composed from head end process to resolution, are done. The results of investigation show as follows. 1. Investigative Test about filtration and dialyzer. (1) The electric conduction is suitable for the judgement of alkyl sodium hydrolysis Alkyl sodium hydrolysis is completed below 39% alcohol concentration. (2) The microfiltration is likely to separate the solid in alcohol waste. (3) From laboratory test, the electrodialyzer is effective for sodium separation in alcohol waste. And sodium remove rate, 96-99%, is confirmed. 2. Conceptual Design. The candidate process is as follows. (1) The head end process is electrodialyzer, and chemical resolution process is catalyst oxidation. (2) The head end process is not installed, and chemical resolution process is catalyst oxidation. (3) The head end process is electrodialyzer, and alcohol extracted by pervaporation. In this Conceptual Design, as far these process, the components, treatment ability, properties of waste, chemical mass balance, safety for fire and explosion, and the plot plan are investigated. As a result, remodeling the existing facility into catalyst oxidation process is effective to treat the alcohol waste, and treatment ability is about 1.25 l/h. (author)
Parraguez, Pedro; Maier, Anja
in the fields of Engineering Design (ED) and Technology and Innovation Management (TIM). Interactions between design and third parties in a range of co-design situations are examined via a targeted literature review, and a map is developed containing a network of keywords. As a result of this review, key...
Friis, Alan; Jensen, Bo Boye Busk
Maintenance of proper hygiene in closed process equipment is in many ways a complex task. The interaction between the physical design and the nature of fluid flow is of main concern. During cleaning the main performance of the flow is to bring cleaning agents in the right doses to all parts of th...... computational fluid dynamics models to be able to predict the cleaning efficiency in especially complex parts of process plants has excellent potentials for desktop improvements and computer pre-validation of the hygienic performance of process plants....
Full Text Available The objective of this paper is to perform the innovation design for the new structures of cam-controlled planetary gear trains (CCPGTs, based on the creative mechanism design methodology. Firstly, the design requirements and design constraints are summarized according to the kinematics characteristics of existing CCPGTs. Then, the (4, 5 and (5, 7 graphs are generated by the theory of number synthesis. After that, the atlas of feasible specialized graphs is obtained. Finally, the atlas of new designs is obtained through the particularization process. In addition, an illustrated example is given, and the feasibility of the design is verified by computer simulation using ADAMS software. The result indicates that new design can produce a more wide range of non-uniform motion than the existing design. Therefore, they are better alternatives for driving a variable speed input mechanism.
Kalantari, Saleh; Snell, Robin
This study was a post-occupancy evaluation (POE) to examine the effectiveness of three specific design innovations in a mental healthcare facility. In addition to collecting data about the impact of these specific designs, the study provides a model for the broader implementation of POE approaches in the mental healthcare context. POEs in general healthcare settings have been shown to lead to better work environments and better outcomes for patients. Despite growing evidence of the value provided by POE studies, the industry has been somewhat slow to adopt their regular use, in part due to unfamiliarity with the POE process. This is particularly true in mental healthcare contexts, where POE studies remain virtually nonexistent. In-depth interviews and a widely distributed, anonymous survey were used to collect hospital staff perceptions and feedback regarding the impact of specific design features. The hospital staff were quite enthusiastic about two of the design innovations studied here (a new wayfinding strategy and the use of vibrant colors in specific areas of the facility). The third innovation, open-style communication centers, elicited more mixed evaluations. The results include extensive hypothesis testing about the effects of each innovation as well as narrative discussions of their pros and cons. The study generated new knowledge about three specific mental healthcare design innovations and provides a model for the practical implementation of a POE approach in mental healthcare contexts. The results are particularly relevant for designers who are considering innovative strategies in future mental healthcare facilities.
Ali Mohammad Sabzghabaee
Full Text Available Background: Nowadays pharmaceutical care departments located in hospitals are amongst the important pillars of the healthcare system. The aim of this study was to evaluate designing features and equipments of hospital drugstores affiliated with Isfahan University of Medical Sciences. Methods: In this cross-sectional study a self-defined and validated questionnaire was used which included all the necessary and standard needed spaces and equipments of an ideal hospital pharmacy. The questionnaire was filled in by one of the researchers in all twelve hospital drugstores located in the teaching and non-teaching hospitals affiliated with Isfahan University of Medical Sciences. Data analysis was done using SPSS (version 14. Results: Results showed that 56% of drugstore space allocations were unsuitable. Used pharmaceutical equipments in 75% of surveyed hospitals were not according to the standards. Almost all of these pharmacies had rather an enough space for storage, but cold storages were not designed in 58% of them. In 66% of perused hospitals, pharmaceutical services disposal level was admissible. The structural engineering parameters like size and dimensions, available spaces, availability of structural planes, existence of air conditioning systems and brightness controllers, adequate stores for drugs and safe places for narcotics were observed in 55% of pharmacies. Conclusions: There are apparent out of standard space allocations and shortages of needed equipments for offering drug services in studied drugstores that may probably lead to a waste of time and money. These issues may reduce the efficiency and safety of pharmaceutical services and drug administration in hospitals.
Full Text Available Based on the analysis of the relationship between the process of product innovation design and knowledge, this article proposes a theoretical model of quality function knowledge deployment. In order to link up the product innovation design and the knowledge required by the designer, the iterative method of quality function knowledge deployment is refined, as well as the knowledge retrieval model and knowledge support model based on quality function knowledge deployment are established. In the whole life cycle of product design, in view of the different requirements for knowledge in conceptual design stage, components’ configuration stage, process planning stage, and production planning stage, the quality function knowledge deployment model could link up the required knowledge with the engineering characteristics, component characteristics, process characteristics, and production characteristics in the four stages using the mapping relationship between the function characteristics and the knowledge and help the designer to track the required knowledge for realizing product innovation design. In this article, an instance about rewinding machine is given to demonstrate the practicability and validity of product innovation design knowledge support technology based on quality function knowledge deployment.
Jensen, Ole Kjeldal
Rapid adaptation to a changing environment is essential for the survival of incumbent companies, but the capabilities required to lead the disruption of a technological trajectory are generally challenged by the process management activities that make the company operate efficiently within its...... current environment. This study explores the practices of engineering designers that are executing disruptive innovation projects for DONG Energy, a Danish energy utilities company. The aim of the study was to understand the role of the designer in disruptive innovation and to create a tool for supporting...... multidisciplinary design teams, while creating disruptive innovations. The results from this study are presented in five research Papers that address the following themes: 1) the willingness of engineers to follow formal procedures, 2) critical knowledge domains in front-end technology decisions, 3) knowledge...
Design for sustainability is a key approach for achieving sustainable development. This PhD study investigates innovation support for companies working on design for sustainability and intermediaries that provide innovation support. The study focuses on Turkey, where design for sustainability is not
Badran, Omar; Al-Salaymeh, Ahmed; El-Tous, Yousif; Abdala, Wasfi
After review of studies conducted on the solar radiation measuring systems, a new innovative instrument that would help in measuring the accurate solar radiation on horizontal surfaces has been designed and tested. An advanced instrument with ease of use and high precision that would enable the user to take the readings in terms of solar intensity (W/m 2 ) has been tested. Also, the innovative instrument can record instantaneous readings of the solar intensities as well as the averages value of the solar radiation flux during certain periods of time. The instrument based in its design on being programmed by programmable interfacing controller (PIC). Furthermore, the power supply circuit is fed by the solar energy cells and does not need an external power source.
Lee, Sang Hoon; Yoo, Kwang Hoon
Floor response spectra for dynamic response of subsystem such as equipment, or piping in nuclear power plant are usually generated without considering dynamic interaction between main structure and subsystem. Since the dynamic structural response generally has the narrow-banded shapes, the resulting floor response spectra developed for various locations in the structure usually have high spectral peak amplitudes in the narrow frequency bands corresponding to the natural frequencies of the structural system. The application of such spectra for design of subsystems often leads to excessive design conservatisms, especially when the equipment frequency and structure are at resonance condition. Thus, in order to provide a rational and realistic design input for dynamic analysis and design of equipment, dynamic equipment-structure interaction (ESI) should be considered in developing equipment response spectrum which is particularly important for equipment at the resonance condition. Many analytical methods have been proposed in the past for developing equipment response spectra considering ESI. However, most of these methods have not been adapted to the practical applications because of either the complexities or the lack of rigorousness of the methods. At one hand, mass ratio among the equipment and structure was used as an important parameter to obtain equipment response spectra. Similarly, Tseng has also proposed the analytical method for developing equipment response spectra using mass ratio in the frequency domain. This method is analytically rigorous and can be easily validated. It is based on the dynamic substructuring method as applied to the dynamic soil-structure interaction (SSI) analysis, and can relatively easily be implemented for practical applications without to change the current dynamic analysis and design practice for subsystems. The equipment response spectra derived in this study are also based on Tseng's proposed method
Eager, David B; Scarrott, Carl; Nixon, Jim; Alexander, Keith
In Australia trampolines contribute one quarter of all childhood play equipment injuries. The objective of this study was to gather and evaluate injury data from a non-traditional, 'soft-edged', consumer trampoline, where the design aimed to minimise injuries from the equipment and from falling off. The manufacturer of the non-traditional trampoline provided the University of Technology Sydney with their Australian customer database. The study involved surveys in Queensland and New South Wales, between May 2007 and March 2010. Initially injury data was gathered by a phone interview pilot study, then in the full study, through an email survey. The 3817 respondents were the carers of child users of the 'soft-edge' trampolines. Responses were compared with Australian and US emergency department data. In both countries the proportion of injuries caused by the equipment and falling off was compared with the proportion caused by the jumpers to themselves or each other. The comparisons showed a significantly lower proportion resulted from falling-off or hitting the equipment for this design when compared to traditional trampolines, both in Australia and the US. This research concludes that equipment-induced and falling-off injuries, the more severe injuries on traditional trampolines, can be significantly reduced with appropriate trampoline design.
Christiansen, John K.; Gasparin, Marta; Varnes, Claus
of the best practices for open innovation. However, projects were not equally successful. The outcome seems to be highly influenced by the type of collaborative arrangements used and their application. In particular, the analysis indicates that organizational factors seem to be indicative but not sufficient...... in open innovation need both a broad knowledge of the various potential elements of an open innovation effort and a flexible attitude toward their application. INSET: Summary of Projects....
Chandrasekhar, U; Arankalle, Avinash
The book presents the best articles presented by researchers, academicians and industrial experts in the International Conference on “Innovative Design, Analysis and Development Practices in Aerospace and Automotive Engineering”. The book discusses new concept designs, analysis and manufacturing technologies, where more swing is for improved performance through specific and/or multifunctional linguistic design aspects to downsize the system, improve weight to strength ratio, fuel efficiency, better operational capability at room and elevated temperatures, reduced wear and tear, NVH aspects while balancing the challenges of beyond Euro IV/Barat Stage IV emission norms, Greenhouse effects and recyclable materials. The innovative methods discussed in the book will serve as a reference material for educational and research organizations, as well as industry, to take up challenging projects of mutual interest.
Lesh, Richard A; Baek, John Y
This Handbook presents the latest thinking and current examples of design research in education. Design-based research involves introducing innovations into real-world practices (as opposed to constrained laboratory contexts) and examining the impact of those designs on the learning process. Designed prototype applications (e.g., instructional methods, software or materials) and the research findings are then cycled back into the next iteration of the design innovation in order to build evidence of the particular theories being researched, and to positively impact practice and the diffusion of the innovation. The Handbook of Design Research Methods in Education-- the defining book for the field -- fills a need in how to conduct design research by those doing so right now. The chapters represent a broad array of interpretations and examples of how today's design researchers conceptualize this emergent methodology across areas as diverse as educational leadership, diffusion of innovations, complexity theory, an...
This study proposes the composite tower design process for large wind turbine equipment. In this work, structural design of tower and analysis using finite element method was performed. After structural design, prototype blade manufacturing and test was performed. The used material is a glass fiber and epoxy resin composite. And also, sand was used in the middle part. The optimized structural design and analysis was performed. The parameter for optimized structural design is weight reduction and safety of structure. Finally, structure of tower will be confirmed by structural test.
This paper outlines the challenge to mining engineers on system design and reliability of equipment and how Hem Heath Colliery in the UK, is meeting this challenge, by describing current systems of work and equipment on the faces, summarising experience gained with succeeding faces, the results achieved, and posing considerations for the future.
Tanev, Stoyan; Storni, Cristiano; Stuedahl, Dagny
The present special issue focuses on the application of ANT to the articulation of a cocreative perspective on design in open innovation environments. The Editors invited submissions by authors using ANT to explore and discuss the link between value co-creation, design and innovation and especially...
We cannot predict the recovery from the financial crisis, but regardless of whether it is slow or quick, the global need for energy and the growth of electricity consumption have been confirmed. Many countries throughout the world are pursuing or have publicly expressed their intention to pursue the construction of Nuclear Power Plants or to extend the life of existing nuclear reactors and to address the back end of the fuel cycle. As always in history, when economic constraints become more severe, the answer is often innovation. Maintaining the high level of performance of nuclear energy and increasing safety with an attractive cost is today’s challenge. It is true for reactors, true also for fuel cycle and in particular for the back end: recycling and interim storage. Interim storage equipment or systems of used fuel are considered in this presentation. The industry is ready to provide support to countries and utilities for the development of radioactive material transportation and storage, and is striving to develop innovative solutions in wet or dry storage systems and casks and to bring them to the market. This presentation will elaborate on the two following questions: Where are the most crucial needs for technological innovations? What is the role of innovation? The needs of technological innovation are important in 3 domains: storage equipment design, interfaces and handling of used fuel and safety justification methodology. Concerning the design, continuous effort for optimisation of used fuel storage equipment requires innovations. These designs constitute the new generation of dry storage casks. The expectations are a higher payload thanks to new materials (such as metal matrix composites) and optimised geometry for criticality-safety, better thermal evacuation efficiency to accept higher fuel characteristics (more enrichment, burnup, shorter cooling time), resistance to impact of airplanes. Designs are also expected to be optimised for sustainable
Tan, C.F.; Chen, W.; Rauterberg, G.W.M.
In this paper, the intuition approach in the design and redesign of the environmental friendly innovative aircraft cabin simulator is presented. The simulator is a testbed that was designed and built for research on aircraft passenger comfort improvement of long haul air travel. The simulation
Liu, Min; Fu, Weiwei; Zhang, Tao
Traditional computer tomography (CT) based on capacitive coupling cannot satisfy the high data rate transmission requirement. We design and experimentally demonstrate a free-space optical transmission system for CT equipment at a data rate of 10 Gb / s. Two interchangeable sections of 12 pieces of fiber with equal length is fabricated and tested by our designed laser phase distance measurement system. By locating the 12 collimators in the edge of the circle wheel evenly, the optical propagation characteristics for the 12 wired and wireless paths are similar, which can satisfy the requirement of high-speed CT transmission system. After bit error rate (BER) measurement in several conditions, the BER performances are below the value of 10 - 11, which has the potential in the future application scenario of CT equipment.
Minder, Bettina; Lassen, Astrid Heidemann
Design thinking has been widely applied as interdisciplinary innovation approach. Simultaneously inclusion of external designers for collaborative learning cycles across different departments have significantly gained importance. However in the context of these debates around design as approach...... and designers as external support, research has paid little attention as to what really happens when designers meet non-designers in innovation processes. We clarify and extend on this literature through drawing on the concept of enthusiasm. We use this concept as foil to analyse collaboration between non...
For many years ergonomists and human engineering specialists have made significant contributions to the solution of problems faced in the area of human labour and to the introduction of their research results and field experience into the process of equipment design. However, the rapid increase in complexity of equipment in use as well as in development demonstrates the necessity of broaden ing the point of view continuously. The workshop held in Munich from March 22nd to March 26th, 1982, was an excellent opportunity for the participants to discuss their respective interests and their interpretation of needs for future research. The workshop was sponsored by the Human Factors Special Programme Panel of the Scientific Affairs Division of NATO. This sponsorship, together with the helpful assistance rendered by Drs. Bayraktar, Kroemer, and Sanders, is gratefully acknowledged. This volume contains the papers presented during the workshop. All these papers are directly related to the general aim: the ex chang...
Wojan, Timothy R; Nichols, Bonnie
Creative class theory explains the positive relationship between the arts and commercial innovation as the mutual attraction of artists and other creative workers by an unobserved creative milieu. This study explores alternative theories for rural settings, by analyzing establishment-level survey data combined with data on the local arts scene. The study identifies the local contextual factors associated with a strong design orientation, and estimates the impact that a strong design orientation has on the local economy. Data on innovation and design come from a nationally representative sample of establishments in tradable industries. Latent class analysis allows identifying unobserved subpopulations comprised of establishments with different design and innovation orientations. Logistic regression allows estimating the association between an establishment's design orientation and local contextual factors. A quantile instrumental variable regression allows assessing the robustness of the logistic regression results with respect to endogeneity. An estimate of design orientation at the local level derived from the survey is used to examine variation in economic performance during the period of recovery from the Great Recession (2010-2014). Three distinct innovation (substantive, nominal, and non-innovators) and design orientations (design-integrated, "design last finish," and no systematic approach to design) are identified. Innovation- and design-intensive establishments were identified in both rural and urban areas. Rural design-integrated establishments tended to locate in counties with more highly educated workforces and containing at least one performing arts organization. A quantile instrumental variable regression confirmed that the logistic regression result is robust to endogeneity concerns. Finally, rural areas characterized by design-integrated establishments experienced faster growth in wages relative to rural areas characterized by establishments using no
The problems encountered in the design of absolute filters (HEPA FILTERS) are presented: glass-fibre filter papers; standards and characteristics: efficiency, fire-resistance, humidity-resistance, radiation-resistance, etc; various types of paper folding: deep folds and small folds, dihedrally mounted; filtering elements; designs; characteristics and quality control; The design of filtration equipment is also analysed: mounting in metal or concrete casings. French and American designs (Regulatory Guide 1-52); and gas-tight casings allowing contaminated filters to be renewed without breaking the gas-tight seal
Farmer, Jane; Carlisle, Karen; Dickson-Swift, Virginia; Teasdale, Simon; Kenny, Amanda; Taylor, Judy; Croker, Felicity; Marini, Karen; Gussy, Mark
Citizen participation in health service co-production is increasingly enacted. A reason for engaging community members is to co-design services that are locally-appropriate and harness local assets. To date, much literature examines processes of involving participants, with little consideration of innovative services are designed, how innovations emerge, develop and whether they sustain or diffuse. This paper addresses this gap by examining co-designed initiatives through the lens of social innovation - a conceptualisation more attuned to analysing grassroots innovation than common health services research approaches considering top-down, technical innovations. This paper considers whether social innovation is a useful frame for examining co-designed services. Eighty-eight volunteer community-based participants from six rural Australian communities were engaged using the same, tested co-design framework for a 12-month design and then 12-month implementation phase, in 24 workshops (2014-16). Mixed, qualitative data were collected and used to formulate five case studies of community co-designed innovations. A social innovation theory, derived from literature, was applied as an analytical frame to examine co-design cases at 3 stages: innovation growth, development and sustainability/diffusion. Social innovation theory was found relevant in examining and understanding what occurred at each stage of innovation development. Innovations themselves were all adaptations of existing ideas. They emerged due to local participants combining knowledge from local context, own experiences and exemplars. External facilitation brought resources together. The project provided a protective niche in which pilot innovations developed, but they needed support from managers and/or policymakers to be implemented; and to be compatible with existing health system practices. For innovations to move to sustainability/diffusion required political relationships. Challenging existing practice
Taps, Stig B.; Brunø, Thomas Ditlev; Nielsen, Kjeld
evaluation of the most commonly tools and techniques in use and suggests a redefinition of the concept of EcoDesign by integrating End-of-Life activities to gain industrial metabolism. This approach takes a broader innovation perspective, necessary to construct a sustainable innovation community...
Willness, Chelsea; Bruni-Bossio, Vince
Integrating literature on entrepreneurial business models and community-based experiential learning, we propose a new framework to advance the practice of curriculum innovation. Grounded in principles of design thinking, the curriculum innovation canvas provides a human-centered, collaborative, and holistic platform for instructors, curriculum…
Describes a typical logging system used in the Lake and Northeastern States, discusses each step in the operation, and presents a simple method for designing and efficient logging system for such an operation. Points out that a system should always be built around the key piece of equipment, which is usually the skidder. Specific equipment types and their production...
Chen, Wang Chih; Chen Jahau Lewis
The work proposes a new design tool that integrates design-around concepts with the algorithm for inventive problem solving (Russian acronym: ARIZ). ARIZ includes a complete procedure for analyzing problems and related resource, resolving conflicts and generating solutions. The combination of ARIZ and design-around concepts and understanding identified principles that govern patent infringements can prevent patent infringements whenever designers innovate, greatly reducing the cost and time associated with the product design stage. The presented tool is developed from an engineering perspective rather than a legal perspective, and so can help designers easily to prevent patent infringements and succeed in innovating by designing around. An example is used to demonstrate the proposed method.
A versatile laboratory for open innovation has been created in a former auto-shop-instruction building adjacent to Gateway High School in the Aurora Public Schools district in Colorado. We have equipped this 2500 square foot space with resources to support fifty-two technologies, such as mechanical design, electronics, optics, and nanotechnology. Correspondingly, we are developing a web site to provide modular instruction around each of these technologies. The goal is to enable collaborations of secondary school students, university students, teachers, professors, and industry partners in an environment richly supported by both physical and educational resources. An Innovation Academy is currently in progress in the lab with projects such as surgery in zero-G and using music to script the motion of actuator arrays in robots and rehabilitation devices.
LUXue-sheng; LIUGuo-rong; YEFeng; JINHui-min; TANGPei-jia
A prototype equipment for monitoring Krypton-85 in situ is designed and set up. A series of relevant software is also developed for remote control, data acquirement and data analysis. Weight of the system is about 300 kg, which is composed of NaI(T1) detector, digi DART, Marillin measurement container and lead shield. The whole system is placed on a homemade go-cart.
Zhao Feiyun; Yao Yangui; Yu Hao; He Yinbiao; Gao Lei; Yao Weida
The safety of strengthening nuclear power design was described based on nuclear equipment design after Fukushima nuclear accident. From these aspects, such as advanced standard system, advanced design method, suitable test means, consideration of beyond design basis event, and nuclear safety culture construction, the importance of nuclear safety improvement was emphatically presented. The enlightenment was given to nuclear power designer. (authors)
Kaleja, Pavol; Kozlovská, Mária
We can observe significant potential of information and communication technologies (ICT) in interior designing field, by development of software and hardware virtual reality tools. Using ICT tools offer realistic perception of proposal in its initial idea (the study). A group of real-time visualization, supported by hardware tools like Oculus Rift HTC Vive, provides free walkthrough and movement in virtual interior with the possibility of virtual designing. By improving of ICT software tools for designing in virtual reality we can achieve still more realistic virtual environment. The contribution presented proposal of an innovative approach of interior designing in virtual reality, using the latest software and hardware ICT virtual reality technologies
Brix, Jacob; Peters, Lois S.
This study builds new empirically based theory on how the processing of an innovation project with a high degree of uncertainty induces change in key components in organization design. By using an embedded case study as our research strategy and organisation design theory as our analytical lens, we...
Eager, David; Scarrott, Carl; Nixon, Jim; Alexander, Keith
In Australia, trampolines contribute approximately one-quarter of all childhood play-equipment injuries. The purpose of this study was to gather and evaluate injury data from a nontraditional, 'soft-edged', consumer trampoline in which the equipment injury sources have been designed out. A survey was undertaken in Queensland and New South Wales. The manufacturer of the nontraditional trampoline provided the University of Technology, Sydney, with their Australian customer database. Injury data were gathered in a pilot study by phone interview, then in a full study through an email survey. Results from 3817 respondents were compared with earlier Australian and US data from traditional trampolines gathered from emergency departments. A significantly lower proportion of the injuries caused by falling off or striking the equipment was found for this new design when compared with traditional trampolines both in Australia and in the USA. The age of children being injured on trampolines in Australia was found to be markedly lower than in North America. This research indicates that with appropriate design the more severe injuries on traditional trampolines can be significantly reduced. © 2012 The Authors. Journal of Paediatrics and Child Health © 2012 Paediatrics and Child Health Division (Royal Australasian College of Physicians).
Objective Creative class theory explains the positive relationship between the arts and commercial innovation as the mutual attraction of artists and other creative workers by an unobserved creative milieu. This study explores alternative theories for rural settings, by analyzing establishment-level survey data combined with data on the local arts scene. The study identifies the local contextual factors associated with a strong design orientation, and estimates the impact that a strong design orientation has on the local economy. Method Data on innovation and design come from a nationally representative sample of establishments in tradable industries. Latent class analysis allows identifying unobserved subpopulations comprised of establishments with different design and innovation orientations. Logistic regression allows estimating the association between an establishment’s design orientation and local contextual factors. A quantile instrumental variable regression allows assessing the robustness of the logistic regression results with respect to endogeneity. An estimate of design orientation at the local level derived from the survey is used to examine variation in economic performance during the period of recovery from the Great Recession (2010–2014). Results Three distinct innovation (substantive, nominal, and non-innovators) and design orientations (design-integrated, “design last finish,” and no systematic approach to design) are identified. Innovation- and design-intensive establishments were identified in both rural and urban areas. Rural design-integrated establishments tended to locate in counties with more highly educated workforces and containing at least one performing arts organization. A quantile instrumental variable regression confirmed that the logistic regression result is robust to endogeneity concerns. Finally, rural areas characterized by design-integrated establishments experienced faster growth in wages relative to rural areas
Vance, R.F.; Brill, B.A.; Carl, D.E.
The equipment as designed, started, and operated for high-level radioactive waste vitrification at the West Valley Demonstration Project in western New York State is described. Equipment for the processes of melter feed make-up, vitrification, canister handling, and off-gas treatment are included. For each item of equipment the functional requirements, process description, and hardware descriptions are presented
van Staveren, Martinus Theodorus
This Ph.D. research generated unique design propositions for implementing existing risk management methodologies in organizations. The resulting design propositions incorporate a synthesis of risk management, innovation management and change management. True implementation of risk management is
The majority of CANDU Fuel Transfer System equipment at Pickering is located under fourteen feet of water, as dictated by the containment and shielding requirements. Such arrangement, however, creates specific problems with equipment maintenance. Each single piece of equipment serves two generating units, which means in case of defect- double losses on production, or two units shut down simultaneously for planned maintenance. The requirement for underwater maintenance was not anticipated at the design stage, which multiples the level of difficulty, and creates requirement for developing special tools for each work. Removal of the damaged fuel from the receiving bays and decontamination of submerged equipment is also part of the problem. The purpose of this presentation is to share our experience with the designers, operators, maintenance mechanics and technical personnel of the other CANDU generating stations
Heumueller, R.; Guse, G.; Dirauf, F.; Fischer, E.
Shorter inspection periods mean lower revision costs and less tight revision schedules, but must not detract from the quality of inspection findings. This requirement imposes upon the company performing the inspection the need for top achievements both in quality management and in the use of innovative techniques. Flexible equipment systems and inspection techniques adapted to specific purposes are able to reduce inspection times in many inspection jobs. As part of a complete system designed to reduce inspection times, the new Saphir (Siemens Alok Phased Array Integrated Reliable UT-System) inspection equipment system is the core of most of the recent innovations. Being an integrated inspection equipment system, it is able to handle conventional US probes as well as arrays and phased arrays. It is open for further matching to specific inspection and administrative requirements and developments, and it may be incorporated in the network of an integrated system with a database. A technological leap in probe design in the past few years has allowed controllable wave fields to be generated which are in no way inferior to those of conventional probes with fixed angles of incidence. In this way, a number of inspection techniques can be implemented with a single probe. This reduces inspection times, setup and retooling times, and doses. Typical examples already used in practice are the LLT (longitudinal-longitudinal-transverse waves) technique and the integration of inspections for longitudinal and transverse defects in a single run. In the near future, surfaces with complicated curvatures will be inspected by novel modular robot systems consisting of individual modules of linear axes and rotational axes. (orig.) [de
Bellon Maurel Véronique
Full Text Available The agro-ecological transition is an ambitious challenge. It can be met by implementing the fundamentals of agroecology (use of biodiversity, integration of agriculture in landscapes, closure of flow loops in the context of a broad and renewed offer of technologies: agro-equipment, biotechnology, digital technologies… This article explores the role that agro-equipment and digital services can play in this transition. These technologies contribute through various levers to the agro-ecological transition: by improving farming efficiency (more service rendered for the same environmental impact, by precision farming (adaptation of the operations to the needs of the plant or the animal based on a monitoring–diagnosis–recommendation cycle and by the development of specialized machinery helping the farmer to achieve “flow loop-closing” (at the plot level, by maintaining the soil quality, or at the farm level, with the recycling of organic effluents or to take advantage of biodiversity (e.g., with agro-equipment adapted to mixed crops. The technological bricks that are requested and for which advances are expected are: sensors (to measure plant or animal needs and associated digital technologies (information transfer, data processing, precision technologies for input application, robotics, specialized machines to manage soil cover and weeds, or for agroforestry. The brakes and engines for innovation in agro-equipment are studied. The brakes are the generally small structure of the farm manufacturing companies, the deficit of the demand from farmers and the complexity − either real or perceived − of these equipments. To encourage innovation, several levers are to be used: involving users in the design of agro-equipments, creating financial incentives for innovative equipment purchase, and training end-users, prescribers and dealers to the high potential of these new technologies. In conclusion, putting agro-equipment and digital technology
Takeda, Nobukazu; Kakudate, Satoshi; Nakahira, Masataka; Shibanuma, Kiyoshi
In the ITER, the neutrons created by D-T reactions activate structural materials, and thereby, the circumstance in the vacuum vessel is under intense gamma radiation field. Thus, the in-vessel components such as blanket are handled and replaced by remote handling equipment. The objective of this report is to study the compactness of the remote handling equipment (a vehicle/manipulator) for the ITER blanket maintenance. In order to avoid the interferences between the blanket and the equipment during blanket replacement in the restricted vacuum vessel, a compact design of the equipment is required. Therefore, the compact design is performed, including kinematic analyses aiming at the reduction of the sizes of the vehicle equipped with a manipulator handling the blanket and the rail for the vehicle traveling in the vacuum vessel. Major results are as follows: 1. The compact vehicle/manipulator is designed concentration on the reduction of the rail size and simplification of the guide roller mechanism as well as the reduction of the gear diameter for vehicle rotation around the rail. Height of the rail is reduced from 500 mm to 400 mm by a parameter survey for weight, stiffness and stress of the rail. The roller mechanism is divided into two simple functional mechanisms composed of rollers and a pad, that is, the rollers support relatively light loads during rail deployment and vehicle traveling while a pad supports heavy loads during blanket replacement. Regarding the rotation mechanism, the double helical gear is adopted, because it has higher contact ratio than the normal spur gear and consequently can transfer higher force. The smaller double helical gear, 996 mm in diameter, can achieve 26% higher output torque, 123.5 kN·m, than that of the original spur gear of 1,460 mm in diameter, 98 kN·m. As a result, the manipulator becomes about 30% lighter, 8 tons, than the original weight, 11.2 tons. 2. Based on the compact design of the vehicle/manipulator, the
A process line is currently being developed for fabrication of high exposure mixed uranium-plutonium core assemblies. This paper describes the design philosophy, process flow, equipment, and the handling and radiation shielding techniques used for inspection of Fast Flux Test Facility (FFTF) fuel pins and assembly of Driver Fuel Assemblies (DFAs) 6 figures
Picon, C.L.; Zaharia B, M.
The objective of this work is to present the possibility to design and construct utilizing local technology, a series of equipment and devices necessaries for a routine in a Radiotherapy Department with typical budget in the Latin-American hospitals. (Author)
Schmoker, D.S.; Swannack, D.L.
In-Service Inspection programs are performed to monitor and verify the integrity of a nuclear power plant's primary pressure boundaries. Early detection of abnormal structural or material degradation could preclude serious damage to plant systems. This paper summarizes results obtained in use of remotely-operated nondestructive testing (NDT) equipment for inspection of reactor system components. Experience obtained in operating the Fast Flux Test Facility (FFTF) has provided a basis for field verification of remote NDT equipment designs and has suggested development improvements. Remote Viewing and data gathering systems used include periscopes, borescopes, fiberscopes, hybrid borescopes/fiberscopes, and closed circuit television. A summary of design consideration for inspection equipment and power plant design is presented to achieve improved equipment operation and reduction of plant maintenance downtime
... real life problem faced by public housing authorities using innovations in affordable housing design... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5689-N-05] 60-Day Notice of Proposed Information Collection: Innovation in Affordable Housing Design Student Competition AGENCY: Office of Policy...
Policy innovation labs are emerging knowledge actors and technical experts in the governing of education. The article offers a historical and conceptual account of the organisational form of the policy innovation lab. Policy innovation labs are characterised by specific methods and techniques of design, data science, and digitisation in public…
Grable, John E.
Innovation in doctoral degree program development and delivery provides an effective counterpoint to the expert-apprentice model established in the Middle Ages. The author outlines the importance of innovation in reaching adult learners and describes an innovative hybrid PhD program designed to allow aspiring doctoral adult-age students to pursue…
This volume contains the proceedings of a conference held in Freiburg, West Germany, September 22-25, 1980, entitled "Manned Systems Design, New Methods and Equipment". The conference was sponsored by the Special Programme Panel on Human Factors of the Scientific Affairs Division of NATO, and supported by Panel VIII, AC/243, on "Human and Biomedical Sciences". Their sponsorship and support are gratefully acknowledged. The contributions in the book are grouped according to the main themes of the conference with special emphasis on analytical approaches, measurement of performance, and simulator design and evaluat ion. The design of manned systems covers many and highly diversified areas. Therefore, a conference under the general title of "Manned Systems Design" is rather ambitious in itself. However, scientists and engineers engaged in the design of manned systems very often are confronted with problems that can be solved only by having several disciplines working together. So it was felt that knowledge about ...
In the ever-growing world of technology, it is becoming more important to understand the developments of new electronic services and mobile applications. Innovative Mobile Platform Developments for Electronic Services Design, and Delivery is a comprehensive look at all aspects of production manag...
BARTHELEMY, RICHARD E.; AND OTHERS
LABORATORY TECHNIQUES AND EQUIPMENT APPROPRIATE FOR TEACHING BIOLOGICAL SCIENCE CURRICULUM STUDY BIOLOGY ARE EMPHASIZED. MAJOR CATEGORIES INCLUDE (1) LABORATORY FACILITIES, (2) EQUIPMENT AND TECHNIQUES FOR CULTURE OF MICRO-ORGANISMS, (3) LABORATORY ANIMALS AND THEIR HOUSING, (4) TECHNIQUES FOR STUDYING PLANT GROWTH, (5) TECHNIQUES FOR STUDYING…
Current regulatory approaches are ill-equipped to address the challenges of governing through periods of disruptive technological change. This article hones in on the use of assessment regimes at the level of the European Union, particularly in the work of the Commission, to argue for a missing...... I label innovation assessment, to steer polities through periods of disruptive technological change, during which innovations have taken concrete forms and are beginning to diffuse, but still exhibit much scope for rapid, unexpected change and alternative trajectories of development. By juxtaposing...
Pigford, Ashlee Ann E.; Hickey, Gordon M.; Klerkx, Laurens
Well-designed and supported innovation niches may facilitate transitions towards sustainable agricultural futures, which may follow different approaches and paradigms such as agroecology, local place-based food systems, vertical farming, bioeconomy, urban agriculture, and smart farming or digital
McKibben, J.M.; Pair, C.R.; Bethmann, H.K.
Construction of the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS) is essentially complete. The facility is designed to convert high-level radioactive waste, now contained in large steel tanks as aqueous salts and sludge, into solid borosilicate glass in stainless steel canisters. All processing of the radioactive material and operations in a radioactive environment will be done remotely. The stringent requirements dictated by remote operation and new approaches to the glassification process led to the development of a number of first-of-a-kind pieces of equipment, new construction fabrication and erection techniques, and new applications of old techniques. The design features and construction methods used in the vitrification building and its equipment were to accomplish the objective of providing a state-of-the-art vitrification facility. 3 refs., 10 figs
Hirota, Shigeo; Kawabata, Yoshinori
The advanced thermal prototype reactor ''Fugen'' attained the criticality on March 20, 1978, and 100% output operation on November 13, 1978. On March 20, 1979, it passed the final inspection, and since then, it has continued the smooth operation up to now. The measuring and control equipments are provided for grasping the operational conditions of the plant and operating it safely and efficiently. At the time of designing, manufacturing and installing the measuring and control equipments for Fugen, it was required to clarify the requirements of the plant design, to secure the sufficient functions, and to improve the operational process, maintainability and the reliability and accuracy of the equipments. Many design guidelines and criteria were decided in order to coordinate the conditions among five manufacturers and give the unified state as one plant. The outline of the instrumentations for neutrons, radiation monitoring and process data, the control systems for reactivity, reactor output, pressure and water supply, the safety protection system, and the process computer are described. Finally, the installations and tests of the measuring and control equipments are explained. The aseismatic capability of the equipments was confirmed. (Kako, I.)
Eines, Trude Fløystad; Vatne, Solfrid
The aim of this study was to evaluate nurses' and nurse assistants' experiences with a design thinking approach to innovation used in a nursing home in Norway. A design thinking approach to innovation that focuses on users' needs can be employed to address many of the challenges facing health care providers in a field facing a growing ageing population, complex diseases and financial shortfalls. This study is based on a thematic analysis of four focus group interviews with nurses and nurse assistants (n = 23). In the initial phase of developing the new service model, which included defining staff roles and responsibilities, participating nurses and nurse assistants felt engaged and motivated by the designers' inclusive and creative methods. However, during the new model's testing phase, they were critical of management's lack of involvement in the model`s implementation and therefore became less motivated about the project. The findings of the study highlight the importance of the designers cooperating with management and staff for the duration of the innovation process. Challenging innovation processes require strong managers who engage with designers, patients, staff and volunteers throughout all phases of an innovation process using a design thinking approach. © 2017 John Wiley & Sons Ltd.
Santos, Isaac J.A. Luquetti; Silva, Carlos Borges da; Santana, Marcos; Carvalho, Paulo Victor R.; Oliveira, Mauro Vitor de; Mol, Antonio Carlos Mol; Grecco, Claudio Henrique; Augusto, Silas Cordeiro
Technology plays an important role in modern medical centers, making health care increasingly complex, relying on complex technical equipment. This technical complexity is particularly noticeable in the nuclear medicine and can increase the risks for human error. Human error has many causes such as performance shaping factors, organizational factors and user interface design. Poorly design human system interfaces of nuclear medical equipment can increase the risks for human error. If all nuclear medical equipment had been designed with good user interfaces, incidents and accidents could be reduced as well as he time required to learn how to use the equipment. Although some manufacturers of nuclear medical equipment have already integrate human factors principles in their products, there is still a need to steer the development of nuclear medical technology toward more human-centered approach. The aim of this paper is to propose a methodology that contributes to the design, development and evaluation of nuclear medical equipment and human system interface, towards a human-centered approach. This methodology includes the ergonomic approach, based on the operator activity analysis, together with human factors standards and guidelines, questionnaires and user based testing. We describe a case study in which this methodology is being applied in evaluation of the thyroid uptake system, getting essential information and data, that ill be used in development of a new system. (author)
Yevgenyevna Maslennikova, Olga; Borisovna Nazarova, Olga; Aleksandrovna Chudinova, Yulia
The paper is dedicated to solving the problem of developing innovative educational systems able to train personnel of complex and dangerous manufacturing industries (such as in metallurgy) to control the process not only under regular conditions, but in emergency and pre-emergency situations as well. At that, such educational systems shall transform training of future and current engineers into a professional activity, model both subject matter and social content of their professional labor. Key characteristics of a 3D atlas of equipment as an educational system are given, as it provides immersion of trainees into professional environment. Requirements for such systems are defined (functional, information, software and technical). Stages of development of a 3D atlas of equipment as an automated system are given, allowing one to get closer to yet another problem that of IT specialist training so that they are able to design, implement and deploy such systems.
van Bruinessen, T.M.
Within the ship design industry, and in particular in the development of large, complex and innovative vessels experienced ship designers play an important role in organizing and structuring the design process. How this actually happens within projects that develop such large, complex and
Ludvigsen, Martin; Rasmussen, Jørgen
of strategic design must be based on actual ongoing processes in live business cases in order to be relevant to a wider audience. The value of purely speculative strategic design research reflections is diminishing as the research field is maturing and solidifying. The work reported in this paper highly......Strategic Design as Agile Driver in Innovating SME´s Poster-paper abstract, DMI2012 conference Martin Ludvigsen and Jørgen Rasmussen Aarhus School of Architecture, Department of Design Nørreport 20, 8000 Aarhus C, Denmark firstname.lastname@example.org, email@example.com The paper reports...... on the last four years of research into strategic design (SD) at Aarhus School of Architecture, Denmark. Under the heading of organizational change and business development through design and user driven value identification, the authors have conducted a range of practice-based SD research projects engaging...
Simon, Joseph J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Doris, Elizabeth S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Farrar, Sara L [National Renewable Energy Laboratory (NREL), Golden, CO (United States)
The U.S. Department of Energy (DOE) Solar Decathlon is a collegiate competition that challenges student teams to design and build full-size, solar-powered houses. Because of balanced design priorities of architecture, engineering, innovation, performance, and energy use, teams have focused on a range of technologies in the built environment, from wall materials to home control systems, from electric lighting to HVAC equipment, and from geothermal to solar photovoltaic technology. This report provides insights into building technology innovation from a review of the Solar Decathlon competition entry designs, anecdotal experiences, and related market reports. The report describes example case studies of the evolution of technology solutions over time to illustrate the innovative, market-driving nature of the Solar Decathlon. It charts technologies utilized in the team designs over seven competitions and compares those to broader market adoption. It is meant to illustrate the technology innovation aspects of the competition, not to be a comprehensive or quantitative analysis. Solar Decathlon also has impacts on public perception of innovative technologies as well as workforce development through the thousands of participating students. The focus of these case studies is to showcase how it contributes to marketplace adoption of innovative energy technologies.
Dr.Ir. Hay Geraedts
Introduction Innovation is crucial for companies who have to react to constantly changing markets. Several national and European research institutes stress the importance of developing innovation for small and medium size enterprises (SMEs). This was a trigger to design a minor on strategic
Thompson, V.R.; Jerram, K.
The project Warrior standing for welding and repair robot in Oldbury reactors is the culmination of more than 7 years of conceptual thinking, research, development design and manufacture. The tile encompasses the whole project which includes a work performing manipulator, serving manipulator, the manipulators control system and consoles, a welding head and rangefinder with its associated control system and consoles and a large amount of auxiliary equipment. The system at the forefront of today's technology has been manufactured to carry out remote welding in nuclear reactors, on plate with an oxide covering of up to 200 microns
Lukacevic, H.; Kopinc, D.; Ivanjko, M.
Terrorist attack in USA in the September 11, 2001 and accident at the Fukushima - Daiichi Nuclear Power Station in the March 11, 2011 highlight the importance of mitigating strategies in responding to Beyond Design Basis Accident (BDBA), while ensuring cooling of reactor core, containment and spent fuel pool. Nuclear Power Plant Krsko (NEK) has acquired additional mobile equipment and made necessary modifications on existing systems for the connection of this equipment (fast couplers). Usage of mobile equipment is not only limited to design basis accident (DBA), but, also to prevent and mitigate the consequences in case of BDBA, when other plant systems are not available. NEK also decided to take steps for upgrade of safety measures and prepared Safety Upgrade Program (SUP), which is consistent with the nuclear industry response to the Fukushima accident and is implementing main projects and modifications related to SUP. NEK mobile equipment is not required to operate under normal reactor plant operation except for periodic surveillance testing and is incorporated into the normal training process. Equipment is dislocated from the reactor building and most of the equipment is located in the new building, able to withstand extreme natural events, including earthquakes and tornadoes. The usage of all mobile equipment is prescribed as an additional option in NEK operating procedures in following cases and enables following options: filling various tanks, filling the steam generators, filling the containment, additional compressed air source, spent fuel pool refilling and spraying, alternative power supply. This document provides an overview of NEK mobile equipment, which consists of various mobile fire protection pumps, air compressors, protective equipment, fire trucks, diesel generators. Sufficient fuel supply for the equipment is provided on site for a minimum three days of operation. (author).
Bjerrum, Eva; Simonsen, John Brøndberg
on experiences from several case studies we propose a way to unfreeze organisations. By using different methods to describe work (ethnographic methods: Observation, episodes, snapshots, photos) and traditional interviews and questionnaires, it is possible to plan and conduct workshop processes that challenge......In Denmark knowledge sharing and working flexibility are considered to be elements that contribute to innovation and improved competitiveness. This has resulted in more and more companies having introduced open flexible office design as a strategic tool to support knowledge sharing. Another reason...... for this focus on workspace design is the change in work and working patterns at knowledge organisations. Both managers and employees work at different places, at customer’s site, while travelling, at hotels and at home, so the focus on the company as being the main workplace changes. The change from traditional...
Hanghøj, Thorkild; Hovmand Sørensen, Sia
and the interplay of different knowledge domains “inside” and “outside” of teacher education. By taking a mixed methods approach, we combine qualitative and quantitative methodologies for studying our case. This involved observations and interviews with selected groups as well as a post-camp survey with all......The aim of this paper is to describe how new teacher students develop innovation competence through problem-based game design processes by participating in an intro camp. The intro camp was held for 350 new teacher students at a Danish university college in 2011, which were asked to solve the real......-life problems of local schools by designing game solutions to be presented for and assessed by participating school directors and pupils. Based upon a pragmatist theoretical framework, we conceptualize the students’ development of innovation competence in relation to creative problem-solving, game frames...
Quinn, J.E.; Berglund, R.C.
This paper reports that the United States nuclear program has been faced with major political, economic and technical challenges in recent years. One US program element, the Liquid Metal Reactor, has addressed these challenges in a systematic, focused manner. The result is an innovative modular design incorporating safety features that utilize inherent characteristics. This Advanced Liquid Metal Reactor (ALMR) is based on the PRISM concept, originated by the General Electric Company in 1981. This design should also be attractive in other developed countries that have deployed, and/or are deploying, nuclear power. The design's safety features can achieve neutronic shutdown and decay heat removal without relying on operator action or engineered active safety features. The ALMR utilizes many innovations including: a passive reactor vessel air cooling system for decay heat removal; the use of a sealed reactor assembly; seismic isolation; electromagnetic primary pumps; and an in-vessel fuel transfer machine. The US ALMR design incorporates a metal fuel core as its reference, however, the required safety performance can also be achieved with an oxide core having similar safety features. This flexibility is particularly important when addressing world wide ALMR applications. The reference ALMR reactor module, of which there are nine in a typical 1395 MW e plant, has a -6 meter by -20 meter vessel and a 471 MW thermal output, with a reactor outlet temperature of 485 degrees C and an overall conversion efficiency of 33%. This plant uses a saturated steam cycle and a non-safety grade secondary sodium system
Vaishnavi, Vijay K
Presenting innovative research methods, this second edition of a bestseller describes a simple and practical methodology for conducting cutting-edge design science research (DSR). It provides comprehensive guidance on how to conduct such research and supplies in-depth treatment of design science theory and the different types of theory that can be generated in design science research.Making novel use of the concept of patterns, it presents 84 research patterns for conducting effective DSR. It emphasizes design science theory throughout and is filled with practical examples of using patterns to
Heller, M. [DPNC-Universite de Geneve, Geneva (Switzerland); Schioppa, E. Jr; Porcelli, A.; Pujadas, I.T.; Della Volpe, D.; Montaruli, T.; Cadoux, F.; Favre, Y.; Christov, A.; Rameez, M.; Miranda, L.D.M. [DPNC-Universite de Geneve, Geneva (Switzerland); Zietara, K.; Idzkowski, B.; Jamrozy, M.; Ostrowski, M.; Stawarz, L.; Zagdanski, A. [Jagellonian University, Astronomical Observatory, Krakow (Poland); Aguilar, J.A. [DPNC-Universite de Geneve, Geneva (Switzerland); Universite Libre Bruxelles, Faculte des Sciences, Brussels (Belgium); Prandini, E.; Lyard, E.; Neronov, A.; Walter, R. [Universite de Geneve, Department of Astronomy, Geneva (Switzerland); Rajda, P.; Bilnik, W.; Kasperek, J.; Lalik, K.; Wiecek, M. [AGH University of Science and Technology, Krakow (Poland); Blocki, J.; Mach, E.; Michalowski, J.; Niemiec, J.; Skowron, K.; Stodulski, M. [Instytut Fizyki Jadrowej im. H. Niewodniczanskiego Polskiej Akademii Nauk, Krakow (Poland); Bogacz, L. [Jagiellonian University, Department of Information Technologies, Krakow (Poland); Borkowski, J.; Frankowski, A.; Janiak, M.; Moderski, R. [Polish Academy of Science, Nicolaus Copernicus Astronomical Center, Warsaw (Poland); Bulik, T.; Grudzinska, M. [University of Warsaw, Astronomical Observatory, Warsaw (Poland); Mandat, D.; Pech, M.; Schovanek, P. [Institute of Physics of the Czech Academy of Sciences, Prague (Czech Republic); Marszalek, A.; Stodulska, M. [Instytut Fizyki Jadrowej im. H. Niewodniczanskiego Polskiej Akademii Nauk, Krakow (Poland); Jagellonian University, Astronomical Observatory, Krakow (Poland); Pasko, P.; Seweryn, K. [Centrum Badan Kosmicznych Polskiej Akademii Nauk, Warsaw (Poland); Sliusar, V. [Universite de Geneve, Department of Astronomy, Geneva (Switzerland); Taras Shevchenko National University of Kyiv, Astronomical Observatory, Kyiv (Ukraine)
The single-mirror small-size telescope (SST-1M) is one of the three proposed designs for the small-size telescopes (SSTs) of the Cherenkov Telescope Array (CTA) project. The SST-1M will be equipped with a 4 m-diameter segmented reflector dish and an innovative fully digital camera based on silicon photo-multipliers. Since the SST sub-array will consist of up to 70 telescopes, the challenge is not only to build telescopes with excellent performance, but also to design them so that their components can be commissioned, assembled and tested by industry. In this paper we review the basic steps that led to the design concepts for the SST-1M camera and the ongoing realization of the first prototype, with focus on the innovative solutions adopted for the photodetector plane and the readout and trigger parts of the camera. In addition, we report on results of laboratory measurements on real scale elements that validate the camera design and show that it is capable of matching the CTA requirements of operating up to high moonlight background conditions. (orig.)
Marvin, B.K.; De Clercq, P.J.; Taylor, B.B.; Mauro, D.M.
An innovative, small-diameter PVC discrete multilevel sampler (DMLS) was designed for the Electric Power Research Institute (EPRI) to provide low-cost, discrete groundwater samples from shallow aquifers. When combined with appropriately-sized direct push soil sampling technologies, high resolution aquifer characterization can be achieved during initial site assessment or remediation monitoring activities. The sampler is constructed from 1-inch diameter PVC well materials, containing polyethylene tubing threaded through PVC disks. Self-expanding annular and internal bentonite seals were developed which isolate discrete sampling zones. The DMLS design allows customization of sampling and isolation zone lengths to suit site-specific goals. Installation of the DMLS is achieved using a temporary, expendable-tipped casting driven by direct push methods. This technique minimizes mobilization costs, site and soil column disturbances, and allows rapid installation in areas of limited overhead clearance. Successful pilot installations of the DMLS prototype have been made at a former manufactured gas plant (MGP) site and a diesel fuel spill site. Analysis of groundwater samples from these sites, using relative compound distributions and contaminant concentration profiling, confirmed that representative discrete samples were collected. This design provides both economical and versatile groundwater monitoring during all phases of site assessment and remediation
Cui Yong Min
Full Text Available The paper solves the increasingly deteriorate environmental problems by positively exploring how to utilize and develop eco-packaging design reasonably. The paper explores an effective method that combines eco-packaging and environmental protection materials, hoping to define the sustainable development road of packaging design. The paper is centered on the design application of eco-packaging and environmental protection materials, applies and analyzes the method to obtain innovative design requirements and development tendency of eco-packaging design by analyzing status and significance of eco-packaging design, combining with the development and main types of eco-packaging packaging materials, and based on the achievements acquired by eco-packaging and environmental protection materials. Meanwhile, the paper also reveals mutual dependence and mutual promotion of eco-packaging design and eco-packaging materials.
Wu, Xianwei; Jin, Wenguang
Human-Computer Interaction (HCI) raises demand of convenience, endurance, responsiveness and naturalness. This paper describes a design of a compact wearable low-power HCI equipment applied to gesture recognition. System combines multi-mode sense signals: the vision sense signal and the motion sense signal, and the equipment is equipped with the depth camera and the motion sensor. The dimension (40 mm × 30 mm) and structure is compact and portable after tight integration. System is built on a module layered framework, which contributes to real-time collection (60 fps), process and transmission via synchronous confusion with asynchronous concurrent collection and wireless Blue 4.0 transmission. To minimize equipment's energy consumption, system makes use of low-power components, managing peripheral state dynamically, switching into idle mode intelligently, pulse-width modulation (PWM) of the NIR LEDs of the depth camera and algorithm optimization by the motion sensor. To test this equipment's function and performance, a gesture recognition algorithm is applied to system. As the result presents, general energy consumption could be as low as 0.5 W.
Storaker, A.; Wever, R.; Dewulf, K.; Blankenburg, D.
In the two last decades a considerable amount of research has been conducted on the Front End of Innovation. This is the stage of the product development process where the design brief is formulated. This phase is argued to be crucial to the success of the final product. While the Front End of
This paper describes in general the typical design/qualification acceptance criteria and seismic acceptance criteria in particular that are applicable for important to safety newly installed pipelines and equipment components of VVER-type already existing NPPs, specifically during the design verification phase of this newly installed equipment. These criteria are currently used for VVER 440-213 and VVER 1000 NPPs in Czech Republic and in Slovakia. The similar criteria are also used in Hungary. (author)
Gnanavel, C.; Saravanan, R.; Chandrasekaran, M.; Jayakanth, J. J.
Measurements and improvements are very indispensable task at all levels of management. Here some samples are, at operator level: Measuring operating parameters to ensure OEE (Overall Equipment Effectiveness) and measuring Q components performance to ensure quality, at supervisory level: measuring operator’s performance to ensure labour utility at managerial level: production and productivity measurements and at top level capital and capacity utilization. An often accepted statement is “Improvement is impossible without measurement”. Measurements often referred as observation. The case study was conducted at Government Boiler factory in India. The scientific approach followed for indentifying non value added activities. Personalised new equipment designed and installed to achieve productivity improvement of 85% for a day. The new equipment can serve 360o around its axis hence it simplified loading and unloading procedures as well as reduce their times and ensured effective space and time.
Baird, Phillip M; Gunter, Elaine W
Part II of this article discusses and provides guidance on the equipment and systems necessary to operate a repository. The various types of storage equipment and monitoring and support systems are presented in detail. While the material focuses on the large repository, the requirements for a small-scale startup are also presented. Cost estimates and a cost model for establishing a repository are presented. The cost model presents an expected range of acquisition costs for the large capital items in developing a repository. A range of 5,000-7,000 ft(2) constructed has been assumed, with 50 frozen storage units, to reflect a successful operation with growth potential. No design or engineering costs, permit or regulatory costs, or smaller items such as the computers, software, furniture, phones, and barcode readers required for operations have been included.
Full Text Available The appropriate implementation of innovation is a crucial factor in improving educational practice. In the implementation process, there is, however, often a lack of interaction between designers and practitioners that would enable the latter to become competent enough to implement theoretical knowledge into practice and to have an ongoing support from designers. Design-based research is based on close cooperation between researchers, practitioners and designers which consequently allows greater integration of research and practice in education. In the present paper, the beginnings, development, basic characteristics, advantages, disadvantages and the research process of design-based research are reviewed and an example of design-based research is presented.
With its focus on the requirements and procedures of tendering and project contracting, this book enables the reader to adapt the basics of power systems and equipment design to special tasks and engineering projects, e.g. the integration of renewable energy sources.
Li, Wei; Wang, Xin; Geng, Jiewen
Taking into account both current status and development trend of digital substation, this paper proposed a design of a new multi-channelled digital power quality monitoring equipment with high compatibility. The overall functional structure, hardware architecture, software architecture, interface architecture and some key techniques such as IEC 61850 modelling of transient event and harmonic measurement method under the condition of non-synchronous sampling are described in this paper.
This book describes new thinking and practice in Advanced Design (ADD) – design that is not merely highly developed but anticipates the future by envisioning novel products and processes. The focus is especially on the front end of innovation and the search for solutions in complex pioneering processes using design-related tools and practices. The book opens by describing these tools, the approaches that characterize ADD, and its historical dimension. Specific fields in which ADD has flourished are then examined, exploring the dynamics between research and design. The coverage ranges from transportation, lighting, and electrical appliances through to business networks, technology parks, and the development of ground-breaking materials. AdvanceDesign is the name of the research group at the Politecnico di Milano (Italy’s largest technical university) of which the authors are members. It was chosen to reflect both the “advanced”, tangible dimension of design in terms of modern product development, mater...
Cordner, Alissa; Klein, Peter T.; Baiocchi, Gianpaolo
This article describes an innovative collaboration between graduate students and a faculty member to co-design and co-teach a graduate-level workshop-style qualitative methods course. The goal of co-designing and co-teaching the course was to involve advanced graduate students in all aspects of designing a syllabus and leading class discussions in…
The book presents the best articles presented by researchers, academicians and industrial experts in the International Conference on “Innovative Design and Development Practices in Aerospace and Automotive Engineering (I-DAD 2016)”. The book discusses new concept designs, analysis and manufacturing technologies, where more swing is for improved performance through specific and/or multifunctional linguistic design aspects to downsize the system, improve weight to strength ratio, fuel efficiency, better operational capability at room and elevated temperatures, reduced wear and tear, NVH aspects while balancing the challenges of beyond Euro IV/Barat Stage IV emission norms, Greenhouse effects and recyclable materials. The innovative methods discussed in the book will serve as a reference material for educational and research organizations, as well as industry, to take up challenging projects of mutual interest.
Thorp Hansen, Claus; Brønnum, Louise
This paper addresses the difficulties seen when working within the user driven innovation [UDI] paradigm. We examine some of the circumstances that often make it difficult to work with user insights in concept design. UDI has become a recognized design approach, but has not yet accommodated...... a design practice explicitly considering the type of user insights this approach implies. For that reason UDI has yet to prove itself and its potential effect; a study of Danish initiative “program for user driven innovation” has shown little effect in this regard. However it has shown that radical new...... insights have been produced but at the same time to abstract when integrated in the design process. We will discuss and propose a framework for working with user insights in concept design, based on existing concept frameworks but actively addressing and incorporating user insights as a new type of input...
Full Text Available Alison L Wong,1,2 Kelly M Lacob,1 Madeline G Wilson,1 Stacie M Zwolski,1 Soumyadipta Acharya1 1Center for Bioengineering, Innovation and Design, Johns Hopkins University, Baltimore, MD, USA; 2Division of Plastic Surgery, Dalhousie University, Halifax, NS, Canada Background: One of the greatest barriers to safe surgery is the availability of functional biomedical equipment. Biomedical technicians play a major role in ensuring that equipment is functional. Following in-field observations and an online survey, a mobile application was developed to aid technicians in troubleshooting biomedical equipment. It was hypothesized that this application could be used to aid technicians in equipment repair, as modeled by repair of a pulse oximeter.Methods: To identify specific barriers to equipment repair and maintenance for biomedical technicians, an online survey was conducted to determine current practices and challenges. These findings were used to guide the development of a mobile application system that guides technicians through maintenance and repair tasks. A convenience sample of technicians in Ethiopia tested the application using a broken pulse oximeter task and following this completed usability and content validity surveys.Results: Fifty-three technicians from 13 countries responded to the initial survey. The results of the survey showed that technicians find equipment manuals most useful, but these are not easily accessible. Many do not know how to or are uncomfortable reaching out to human resources. Thirty-three technicians completed the broken pulse oximeter task using the application. All were able to appropriately identify and repair the equipment, and post-task surveys of usability and content validity demonstrated highly positive scores (Agree to Strongly Agree on both scales.Discussion: This research demonstrates the need for improved access to resources for technicians and shows that a mobile application can be used to address a gap in
Full Text Available Laundry business is popular service business in Indonesia that mostly involve muscle activity for lifting and ironing activity. It causes the worker get muscular fatigue and injury especially for ironing activity that is included in the static and monotonous activity. moreover, existed ironing board design in the market is not easy to be adjusted to standing or sitting position of workers. Hence, this paper aimed to design the innovative and adjustable ironing board to minimize the musculoskeletal complaint. The preliminary study is conducted by NBM questionnaires found that fatigue experienced mostly in the back, right upper arm, and calves. The product designed by Kansei engineering to satisfy consumer's feeling and assessed by USE questionnaire to fulfil consumer's usability. Orthogonal array and conjoint analysis were conducted to incorporate all attribute potentials in developing a new single concept design. Statistical analysis was also done to test the hypothesis. 80 respondents have participated in this study. The result of this study is an innovative design of ironing board which is valid to meet consumers' needs such as comfort, secure, attractive, sturdy, durable and multifunction and practical at 5% of the significant level.
Deckers, E.J.L.; Stouw, van der B.; Peutz, J.
This paper presents an ongoing innovation project on the development of an intelligent and interactive carpet called PeR+, short for Perception Rug Plus. This design-research project is a collaboration between an international flooring company, DESSO, and the Department of Industrial Design at the
Hald, Frederik; Kirkegaard, Poul Henning; Sørensen, John Dalsgaard
Robustness of structural systems has obtained a renewed interest due to a much more frequent use of advanced types of structures with limited redundancy and serious conse-quences in case of failure. The present paper summaries issues with respect to robustness of timber structures. Two different...... large span timber structures are analyzed and based on these analyses the paper presents guidelines for the future development of innovative timber struc-tures which are robust with respect to design and execution errors, unforeseen degradation and other potential hazards....
This volume consists of 65 E size drawings and 4 sketches of the NUS spent fuel rod consolidation equipment. The drawings have been grouped into categories; a detailed list of the drawings is included. The sketches prepared during the preliminary design process have been included
Harper, Meghan; Deskins,Liz
This article describes a collaborative project designed to use action research to assess and advocate for innovative design changes in a school library. The high school library was in its fifth year of service, and yet the layout of the library was not meeting the learning and technological needs of 21st-century high school students. The purpose…
Rice, P.; Smith, A.M. [EG& G Idaho, Inc., Idaho Falls, ID (United States). Idaho National Engineering Lab.; Peterson, R.
This test plan describes the demonstration of innovative equipment and processes specifically designed to be superior to currently employed technology for buried waste retrieval. The dumping of dry soil into a funnel/dumpster arrangement has been found to be the primary mechanism for dust generation during the retrieval of buried transuranic waste. The primary goal of the innovative end effector is to reduce dust generation and the potential spread of airborne contaminants during the dumping operation. In addition, regardless of the excavation technique, exhumed waste will have to be conveyed away from the retrieval area to a packaging area or directly to a treatment facility. The remote conveyance system is aimed at developing a remotely controlled vehicle to convey retrieved waste that will operate on variable terrain and remove workers from the hazardous zone. To demonstrate the remote conveyance system and the innovative end effector, the Buried Waste Integrated Demonstration (BWID) Program has subcontracted with RAHCO International to provide equipment and services to perform a demonstration of the technologies. The demonstration will be performed in two phases. In Phase I, the subcontractor will perform a full scale demonstration to assess the ability of the innovative end effector to control dust generation and the potential spread of contamination during dumping operations. Phase II includes performing a retrieval/conveyance demonstration. This demonstration will excavate, dump, and convey simulated waste to demonstrate the functionality of the system (e.g., maneuverability, retrieval rates, and system integration). Phase II of the demonstration will include all elements of the remote conveyance and end effector system. This test plan will describe the demonstration objectives, data quality objectives, equipment operation, and methods for collecting data during the demonstration.
Rice, P.; Smith, A.M.; Peterson, R.
This test plan describes the demonstration of innovative equipment and processes specifically designed to be superior to currently employed technology for buried waste retrieval. The dumping of dry soil into a funnel/dumpster arrangement has been found to be the primary mechanism for dust generation during the retrieval of buried transuranic waste. The primary goal of the innovative end effector is to reduce dust generation and the potential spread of airborne contaminants during the dumping operation. In addition, regardless of the excavation technique, exhumed waste will have to be conveyed away from the retrieval area to a packaging area or directly to a treatment facility. The remote conveyance system is aimed at developing a remotely controlled vehicle to convey retrieved waste that will operate on variable terrain and remove workers from the hazardous zone. To demonstrate the remote conveyance system and the innovative end effector, the Buried Waste Integrated Demonstration (BWID) Program has subcontracted with RAHCO International to provide equipment and services to perform a demonstration of the technologies. The demonstration will be performed in two phases. In Phase I, the subcontractor will perform a full scale demonstration to assess the ability of the innovative end effector to control dust generation and the potential spread of contamination during dumping operations. Phase II includes performing a retrieval/conveyance demonstration. This demonstration will excavate, dump, and convey simulated waste to demonstrate the functionality of the system (e.g., maneuverability, retrieval rates, and system integration). Phase II of the demonstration will include all elements of the remote conveyance and end effector system. This test plan will describe the demonstration objectives, data quality objectives, equipment operation, and methods for collecting data during the demonstration
S. G. Selivanov
designing;- implementing the high and critical technologies when developing the innovation projects for renewal of manufacturing process or equipment to produce innovative products in computeraided systems of production engineering (CASPE.
Oka, Kiyoshi; Tada, Eisuke [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment
The ITER machine has three Neutral Beam Injectors (NBIs) placed tangential to the plasma at a minimum radius of 6.25 m. During operation, neutrons produced by the D-T reactions will irradiate the NBI structure and it will become radioactive. Radiation levels will be such that all subsequent maintenance of the NBIs must be carried out remotely. The presence of tritium and possibly radioactive dust requires that precautions be taken during maintenance to prevent the escape of these contaminants beyond the prescribed boundaries. The scope of this task is both the development of remote maintenance procedures and the design of the remote handling equipment to handle the NBIs. This report describes the design of remote handling tools for the ion source and its filaments, transfer cask, maintenance time, manufacturing schedule and cost estimation. (author)
Alting, Leo; Clausen, Christian; Jørgensen, Ulrik
The paper reflects on research perspectives dealing with the incorporation of knowledge on use, users, customers and market in the entire innovation process. The point will be made that the support of user oriented innovation processes will have to deal with development of new approaches, methods...
Katoh, Atsushi; Hayafune, Hiroki; Kotake, Shoji
Highlights: • Japan Sodium Cooled Fast Reactor (JSFR) is designed to reduce plant commodity. • Cost reduction effectiveness by innovative designs is estimated by bottom up method. • JSFR achieves 76% construction cost reduction compared with Monju by design effort. • Commercial JSFR construction cost could be less than that of conventional LWR. - Abstract: To improve the economic competitiveness of the Japan Sodium-cooled Fast Reactor (JSFR), several innovative designs have been introduced, e.g. reduction of number of main cooling loop, shorter pipe arrangement by adopting thermally durable material, in fact high chromium ferrite steel, a compact reactor vessel (RV), integration of a primary pump and an intermediate heat exchanger (IHX). Since they had not been introduced in the past and existing reactors, a new approach for construction cost estimation has been introduced to handle innovative technologies, for example, concerning different kinds of material, fabrication processes of equipment etc. As results of JSFR construction cost estimations based on the new method and the latest conceptual JSFR design, economic goals of Generation IV nuclear energy systems can be achieved by expecting the following cost reduction effects: commodity reduction by adopting innovative design, an economy of scale by power generation increase, learning effect etc. It is well analyzed quantitatively that feasibility of innovative designs is essential for economic competitiveness of JSFR
Katoh, Atsushi, E-mail: firstname.lastname@example.org [Japan Atomic Energy Agency, 4002 Narita, Oarai-machi, Higashi-ibaraki-gun, Ibaraki-ken 311-1393 (Japan); Hayafune, Hiroki [Japan Atomic Energy Agency, 4002 Narita, Oarai-machi, Higashi-ibaraki-gun, Ibaraki-ken 311-1393 (Japan); Kotake, Shoji [The Japan Atomic Power Company, 1-1 Kanda-midoricyo, Chiyoda-ku, Tokyo-to 101-0053 (Japan)
Highlights: • Japan Sodium Cooled Fast Reactor (JSFR) is designed to reduce plant commodity. • Cost reduction effectiveness by innovative designs is estimated by bottom up method. • JSFR achieves 76% construction cost reduction compared with Monju by design effort. • Commercial JSFR construction cost could be less than that of conventional LWR. - Abstract: To improve the economic competitiveness of the Japan Sodium-cooled Fast Reactor (JSFR), several innovative designs have been introduced, e.g. reduction of number of main cooling loop, shorter pipe arrangement by adopting thermally durable material, in fact high chromium ferrite steel, a compact reactor vessel (RV), integration of a primary pump and an intermediate heat exchanger (IHX). Since they had not been introduced in the past and existing reactors, a new approach for construction cost estimation has been introduced to handle innovative technologies, for example, concerning different kinds of material, fabrication processes of equipment etc. As results of JSFR construction cost estimations based on the new method and the latest conceptual JSFR design, economic goals of Generation IV nuclear energy systems can be achieved by expecting the following cost reduction effects: commodity reduction by adopting innovative design, an economy of scale by power generation increase, learning effect etc. It is well analyzed quantitatively that feasibility of innovative designs is essential for economic competitiveness of JSFR.
McDougall, Dennis; Smith, Douglas
This article illustrates an innovative small-N research design that researchers and practitioners can use to investigate questions of interest in "professional school counseling." The distributed criterion (DC) design integrates elements of three classic small-N research designs--the changing criterion, reversal, and multiple baseline. The DC…
import- ing Silicon Valley- style innovation practices to its acquisition process, it is im- portant to assess an organization’s ability to...these efforts. Keywords: defense acquisition, defense procurement, rapid acquisition, de- fense innovation, program management , organizational culture...Device De- feat Organization, JIEDDO, Rapid Equipping Force, REF Silicon Valley- style innovation is a hot topic in the Department of De-fense (DOD). For
Svare, Helge; Gausdal, Anne Haugen
The primary objective of this paper is to demonstrate how regional innovation system theory may be translated into manageable micro-level methods with the potential for strengthening the productive dynamics of a regional innovation system. The paper meets this objective by presenting network-based innovation brokering (NBIB), a practical method designed using insights from regional innovation system theory and trust theory. Five cases from two Norwegian regional innovation networks show that ...
Grozdanovic, Miroljub; Jekic, Savko; Stojiljkovic, Evica
Adequate application of the static and dynamic anthropometric measures of pre-school children in ergonometric design of children's playground equipment should eliminate all dangers and difficulties in their use. Possibilities of injuries, insecure movements, discomfort able positions and some other dangerous actions may be minimized; and safety and health protection of pre-school children will be increased. Children's playground represents a significant space of activity for pre-school children. Therefore, it is necessary to apply ergonomic principles which contribute to the adjustment of the playground elements to children's anatomic features. Based on the results presented in this paper, new constructions were designed and new playgrounds were installed in Serbia. Participants were children from three pre-school age groups: Junior age group (3-4 years of age, 17 children), Medium age group (4-5 years of age, 22 children), and Senior age group (5-6 years of age, 26 children). Thirty-one static anthropometric measures (12 in standing position, 11 in sitting position, 7 related to dimensions of hand, foot an head, with body weight and shoe size) and 15 dynamic anthropometric measures (7 in standing position, 6 in sitting position and 2 dimension of foot and hand) were defined for the study. Measurements were taken using an anthrop-meter, a flexible measuring tape. Equations for ergonomic design of children's playground elements were also defined. Basic statistical data of static and dynamic anthropometric measurements of the pre-school children are presented in this paper, as well as the statistical calculation of the corrective anthropometric measurements. Measurements were performed in "Poletarac" kindergarten, part of the pre-school institution "Radost" in Cacak. Elements of playground equipment in "Bambi" kindergarten in Kragujevac (the Indian tent "wigwam", gate-house, swing and carousel) were designed and built using these parameters. Based on the obtained
There is a renewed interest in Member States in the development and application of small and medium sized reactors (SMRs). In the near term, most new NPPs are likely to be evolutionary designs building on proven systems while incorporating technological advances and often the economics of scale, resulting from the reactor outputs of up to 1600 MW(e). For the longer term, the focus is on innovative designs aiming to provide increased benefits in the areas of safety and security, non-proliferation, waste management, resource utilization and economy, as well as to offer a variety of energy products and flexibility in design, siting and fuel cycle options. Many innovative designs are reactors within the small-to-medium size range, having an equivalent electric power less than 700 MW(e) or even less than 300 MW(e). The projected timelines of readiness for deployment are generally between 2010 and 2030. The objective of this report is to provide Member States, including those just considering the initiation of nuclear power programmes, and those already having practical experience in nuclear power, with a balanced and objective information on important development trends and objectives of innovative SMRs for a variety of uses, on the achieved state-of-the-art in design and technology development for such reactors and on their design and regulatory status. The report is intended for many categories of stakeholders, including regulators, electricity producers, designers, non-electrical producers and policy makers. The main chapters of this report, addressed to all abovementioned groups of stakeholders, provide a summary of major specifications, applications and user-related special features of innovative SMRs, outline the achieved design and regulatory status and its progress since previous IAEA publications, review targeted deployment dates, fuel cycle options, design approaches used to meet design objectives in specific subject areas, enabling technologies and current
Scott, Sally; McGuire, Joan
Universal Design applied to college instruction has evolved and rapidly spread on an international scale. Diffusion of Innovation theory is described and used to identify patterns of change in this trend. Implications and strategies are discussed for promoting this inclusive approach to teaching in higher education.
Yu, Seung Nam; Lee, Jong Kwang; Lee, Hyo Jik
At present, each item of process equipment required for integrated processing is being examined, based on experience acquired during the Pyropocess Integrated Inactive Demonstration Facility (PRIDE) project, and considering the requirements and desired performance enhancement of KAPF as a new facility beyond PRIDE. Essentially, KAPF will be required to handle hazardous materials such as spent nuclear fuel, which must be processed in an isolated and shielded area separate from the operator location. Moreover, an inert-gas atmosphere must be maintained, because of the radiation and deliquescence of the materials. KAPF must also achieve the goal of significantly increased yearly production beyond that of the previous facility; therefore, several parts of the production line must be automated. This article presents the method considered for the conceptual design of both the production line and the overall layout of the KAPF process equipment. This study has proposed a design methodology that can be utilized as a preliminary step for the design of a hot-cell-type, large-scale facility, in which the various types of processing equipment operated by the remote handling system are integrated. The proposed methodology applies to part of the overall design procedure and contains various weaknesses. However, if the designer is required to maximize the efficiency of the installed material-handling system while considering operation restrictions and maintenance conditions, this kind of design process can accommodate the essential components that must be employed simultaneously in a general hot-cell system
Jafar Syahbuddin Ritonga
Full Text Available Desain Kurikulum, Kemampuan Inovasi dan Performa: Studi Pesantren di Sumatera Utara. There have been many articles and studies on Pesantren that have been published. Unfortunately, Almost all of them discuss about the Pesantren from the perspective of Islam exclusively. This paper tries to offer a new perspective in looking at the Pesantren: as an entity of business. This is a research paper which aims to know how Pesantrens’ performances are influenced by designing curriculum at different levels of capacity of innovation. The data are analyzed using descriptive and inferential statistics, namely frequency, multiple regressions and hierarchical regression. This paper analyzes the influence of designing the curriculum on performances of the Pesantren and the important effects of capacity of innovation on them. This paper reveals that the influence of designing modern Islamic currciculum to the Pesantren’s performances is expected to be varied according to the levels of capacity of innovation at the Pesantren.
Tveden-Nyborg, Svend; Boelt, Birte; Misfeldt, Morten
seed scientists from Aarhus University will work together with seed growers and seed company consultants in designing a collaborative knowledge platform to optimise the diffusion of innovation between them. The aim of the Ph.D. project is to look at the processes within the three communities......For many years the Danish seed industry has been at the forefront with high quality seed production, but in a rapidly changing global market innovation is a key factor for the future of Danish seed production - one important element to innovation is transfer of knowledge. In a new Ph.D. project...... of practice in their participatory efforts to design and select technologies that will improve their knowledge dissemination through a shared understanding of learning and innovation within the Danish seed industry. The research questions are: •What boundary objects emerge between and within the collaborating...
Tveden-Nyborg, Svend; Boelt, Birte; Misfeldt, Morten
For many years the Danish seed industry has been at the forefront with high quality seed production, but in a rapidly changing global market innovation is a key factor for the future of Danish seed production - one important element to innovation is transfer of knowledge. In a new Ph.D. project...... seed scientists from Aarhus University will work together with seed growers and seed company consultants in designing a collaborative knowledge platform to optimise the diffusion of innovation between them. The aim of the Ph.D. project is to look at the processes within the three communities...... of practice in their participatory efforts to design and select technologies that will improve their knowledge dissemination through a shared understanding of learning and innovation within the Danish seed industry. The research questions are: •What boundary objects emerge between and within the collaborating...
The philosophy of seismic design for nuclear power plant facilities in Japan is based on 'Examination Guide for Seismic Design of Nuclear Power Reactor Facilities: Nuclear Power Safety Committee, July 20, 1981' (referred to as 'Examination Guide' hereinafter) and the present design criteria have been established based on the survey of governmental improvement and standardization program. The detailed design implementation procedure is further described in 'Technical Guidelines for Aseismic Design of Nuclear Power Plants, JEAG4601-1987: Japan Electric Association'. This report describes the principles and design procedure of the seismic design of equipment/piping systems for nuclear power plant in Japan. (J.P.N.)
Minematsu, Akiyoshi [Tokyo Electric Power Co., Inc. (Japan)
The philosophy of seismic design for nuclear power plant facilities in Japan is based on `Examination Guide for Seismic Design of Nuclear Power Reactor Facilities: Nuclear Power Safety Committee, July 20, 1981` (referred to as `Examination Guide` hereinafter) and the present design criteria have been established based on the survey of governmental improvement and standardization program. The detailed design implementation procedure is further described in `Technical Guidelines for Aseismic Design of Nuclear Power Plants, JEAG4601-1987: Japan Electric Association`. This report describes the principles and design procedure of the seismic design of equipment/piping systems for nuclear power plant in Japan. (J.P.N.)
Every day, people around the world rely on intermittent and indwelling urinary catheters to manage bladder dysfunction, but the potential or actual harm caused by these devices is well-recognised. Current catheter designs can cause urinary tract infection and septicaemia, bladder and urethral trauma and indwelling devices frequently become blocked. Furthermore, the devices can severely disrupt users' lives, limiting their daily activities and can be costly to manage for healthcare providers. Despite this, little significant design innovation has taken place in the last 80 years. In this article current catheter designs and their limitations are reviewed, common catheter-associated problems are outlined and areas of design ripe for improvement proposed. The potential to relieve the individual and economic burden of catheter use is high.
Nielsen, Janni; Yaganeh, Suzanne; Bloch Rasmussen, Leif
This paper contributes to a theoretical discussion of creation of innovation with participants in, or outside, organisations. We address the creation of innovation with a complex theoretical understanding drawing on the Scandinavian and the Participatory Design tradition introducing two approaches...... to the processes of innovation. We ask if innovation can be initiated and enhanced looking at two collaborative approaches; participatory innovation (PIN) and cooperative innovation (COIN). We invite to dialogue and reflections on PIN’s conflict and creative frictions on one side and COIN’s complexity......, complementarity in diversity and the didactic scaffolding of the innovation process on the other side. Our contribution focuses on the methods and practices for facilitation of co-creating activities between different groups leading to cooperation, and innovation in thinking....
del Castillo, Jacqueline; Bhatti, Yasser; Hossain, Mokter
We examine the potential of an open innovation digital platform to expose a local innovation process to a greater number of ideas and a more inclusive set of stakeholders. To do so we studied an online innovation challenge on the OpenIDEO to reimagine the end-of-life experience sponsored by Sutte...... it leads to a greater number of ideas from a wider and more inclusive set of stakeholders. We offer insights for the literatures on open innovation and design thinking in a healthcare context....
Brem, Alexander; Nylund, Petra; Schuster, Gerd
investigate how the existence of a dominant design affects subsequent innovation in an industry. In particular, we study the influence on innovative performance, radical innovation, and process innovation. Analyzing longitudinal, cross-sectional patent data for more than 2.6 million patents filed from 1978...... to 2013, we find support for our hypotheses that an industry's innovative performance and degree of radical innovation are negatively influenced by dominant design in that industry, and that process innovation is fostered by the occurrence of a dominant design. We discuss the findings in the light...... of the increasing speed of technological development and standardization. Additionally, results from a sensitivity analysis for different threshold values of dominant design call for adjusting a binary definition of dominant design with different threshold values depending on the effects under study....
Mao Xiaoming; Qin Xijiu; Ding Hu; Xue Zhaoqun; Wen Shengjun
As a main channel for the foreign economic cooperation of China nuclear industry, China Zhongyuan Engineering Corporation (CZEC) has been constantly engaged in technical modifications and management innovations in its exporting nuclear reactor projects. In the implementation of heavy water research reactor contract in Algeria, CZEC had established a complete and adequate design standards system in compliance with the international standards, and made significant modifications to the reference reactor in the aspects of reactor power and reactor safety, solved quite some technical issues which-affected the reactor technical performance. The modifications and improvements enabled the technical parameters, safety features, reactor multipurpose application to attain to the advanced level in the world. In the 300 MWe PWR NPPs in Pakistan, safety features had been updated in line with upgrading regulatory requisites. The design philosophy and technology application demonstrated CZEC' s creation and innovation on basis of constant safety enhancement of nuclear power projects. Efforts had also been made by CZEC' s creation and innovation on basis of constant safety enhancement of nuclear power projects. Efforts had also been made by CZEC in promoting China made equipment items and components exportation. (authors)
The IAEA, within the framework of its Nuclear Energy Department’s Technical Working Group on Fast Reactors (TWG-FR), assists Member States activities in fast reactors technology development areas by providing an umbrella for information exchange [topical Technical Meetings (TMs), Workshops and large Conferences] and collaborative R&D [Coordinated Research Projects (CRPs)]. The Technical meeting on “Innovative Heat Exchanger and Steam Generator Designs for Fast Reactors” was held from 21 – 22 December 2011 in Vienna, addressing Member States’ expressed needs of information exchange in the field of advanced fast reactor design features, with particular attention to innovative heat exchangers and steam generators. The Objective of the TM is to provide a global forum for in-depth information exchange and discussion on the most advanced concepts of heat exchangers and steam generators for fast reactors. More specifically, the objectives are: · Review of the status of advanced fast reactor development activities with special emphasis on design and performance of heat exchangers and steam generators; · Discuss requirements for innovative heat exchangers and steam generators; · Present results of studies and conceptual designs for innovative heat exchangers and steam generators; · Provide recommendations for international collaboration under the IAEA aegis. The meeting agenda of the meeting is in Annex I
Lee, J. Y.; Kim, S. H.; Song, T. G.; Yoon, J. S
In this study, the graphic design system is developed for designing the spent fuel rod consolidation and the dismantling processes. This system is used throughout the design stages from the conceptual design to the motion analysis. Also, the real-time control system of the rod extracting equipment is developed. This system utilizes the graphic simulator which simulates the motion of the equipment in real time by synchronously connecting the control PC with the graphic server through the TCP/IP network. The developed system is expected to be used as an effective tool in designing the process equipment for the spent fuel management. And the real-time graphic control system can be effectively used to enhance the reliability and safety of the spent fuel handling process by providing the remote monitoring function of the process.
Lee, J. Y.; Kim, S. H.; Song, T. G.; Yoon, J. S.
In this study, the graphic design system is developed for designing the spent fuel rod consolidation and the dismantling processes. This system is used throughout the design stages from the conceptual design to the motion analysis. Also, the real-time control system of the rod extracting equipment is developed. This system utilizes the graphic simulator which simulates the motion of the equipment in real time by synchronously connecting the control PC with the graphic server through the TCP/IP network. The developed system is expected to be used as an effective tool in designing the process equipment for the spent fuel management. And the real-time graphic control system can be effectively used to enhance the reliability and safety of the spent fuel handling process by providing the remote monitoring function of the process
Hermann, Roberto Rivas; Smink, Carla; Kerndrup, Søren
Air pollution from maritime transportation has become an important public health and environmental concern. As result, new international regulations seek to reduce the pollutants issuing from marine fuels combustion. Marine cleaner technology has been regarded as the key solution to comply...... with regulations and reduce operation costs. However, definitions of maritime cleantech differ and range from end-of-pipe pollution control equipment, more efficient engines, improved hull-design and alternate propulsion fuels (LNG, methanol). Different constellations of actors seem to follow different cleantech...... trajectories. It is therefore important to develop new forms of governance in order to create innovations which are comparable with the state of art in other industries and new ways of building networks and partnerships. The paper aims to improve the understanding of cleaner technology as innovative...
Full Text Available Automation is replacing white-collar office work and non-dexterous manual work, causing major structural change in the job market. As advanced economies shift from a post-industrial to an auto-industrial model, all kinds of routine work is being replaced by machines. Mid-range job opportunities are shrinking, and labor markets are polarizing. Demand for dexterous service work nevertheless remains strong, as does demand for abstract labor working with patterns rather than with rules or procedures. Design is a mid-tier occupation that is growing rather than declining. “Design” is also a metaphor for abstract labor of all kinds; it exemplifies work that is creative, innovative, problem-solving, and reliant on judgment rather than rules. Heightened demand for abstract labor reflects the evolving nature of capitalist economies. The contribution of invention, ingenuity and imagination to the creation of economic value continues to expand. The auto-industrial era is coeval with design capitalism; together they represent a key dimension of future economics.
Biffi, Alfredo; Bissola, Rita; Imperatori, Barbara
Purpose: The purpose of this paper is to illustrate and discuss the main features and key challenges of an original post-graduate education program designed according to an innovative theoretical framework promoting design thinking in a rhizomatic approach. By involving different stakeholders, the aim of this entrepreneurship education program is…
Winterhalter, Stephan; Zeschky, Marco; Gassmann, Oliver; Weiblen, Tobias
Frugal Innovation is an extreme case of innovation: radically new applications are innovated for an environment of extreme resource and cost constraints. While the phenomenon of frugal innovation has been described from a product perspective, very little is known about how firms organize frugal innovation on a business model level. This study is based on a multiple case study approach investigating five business models for frugal innovation in the context of the medical equipment market in em...
Austin, Robert D.; Devin, Lee; Sullivan, Erin E.
Historical accounts of human achievement suggest that accidents can play an important role in innovation. In this paper, we seek to contribute to an understanding of how digital systems might support valuable unpredictability in innovation processes by examining how innovators who obtain value from...... they incorporate accidents into their deliberate processes and arranged surroundings. By comparing makers working in varied conditions, we identify specific factors (e.g., technologies, characteristics of technologies) that appear to support accidental innovation. We show that makers in certain specified...... conditions not only remain open to accident but also intentionally design their processes and surroundings to invite and exploit valuable accidents. Based on these findings, we offer advice for the design of digital systems to support innovation processes that can access valuable unpredictability....
Valkokari , Katri; Amitrano , Cristina ,; Bifulco , Francesco; Valjakka , Tiina
Part 13: Design Science and Business Models - Design Science Research; International audience; Through a design science approach, the paper explores how actors in a network create and sustain competitive advantage independently and through participation in a system of actors (i.e., a collaborative network) who are not hierarchically managed but, rather, act toward their own goals within the innovation ecosystem. In accordance with design studies, the relevance of research and its quality are ...
Full Text Available Design is a social phenomenon and researchers suggest that social interaction, negotiations and communication between designers are essential to initiate creativity. Within the design studio environment, a number of factors affect the healthy social interaction and design negotiations, such as the teaching style of tutors and the culture that governs a design studio’s environment. This may in turn affect the utilization of the outcome of negotiations in the design project. Design studio students from the third to fifth years at the College of Architecture, University of Dammam (UD, the Kingdom of Saudi Arabia (KSA, were surveyed to find out how far the design studio’s culture and communication would impact the production of innovative design projects. The results show that frequent communication and the establishment’s shared grounds are essential to develop knowledge and positively influence the design outcome. On the other hand, the research found that negative qualities on a personal level and on that of a design studio environment would hinder a student’s creativity. However, to develop students’ design/innovative abilities, the researcher recommends that certain measures should be considered. These would include transforming the design studio into an interactive and friendly learning environment, adjusting the teaching methodology, and developing interactive communication abilities of students and tutors.
Zhang Yanmin; An Jigang; Zhou Liye; Liu Yisi; Wu Zhifang; Xiang Xincheng; Huang Songling
The author introduced the design principle of Inspection Equipment Vehicle of TCM-SCAN Mobile 60 Co container inspection system. Three schemes had been compared. The scheme of scan gate in form of pucker-able rails standing on the vehicle was determined. Prototype was prepared in September 1999. Mobile 60 Co container inspection system had the same inspection performance of fixed 60 Co container inspection system
Mogensen, Jeppe; Jørgensen, Poul-Erik; Poulsen, Søren Bolvig
Concerned with the overall challenges of implementing design innovations, this paper relates to the specific case of applying smart textiles in future hospital interiors. The methodological approach is inspired by design thinking and implementation processes, and through the scope of a developed ...
Full Text Available In this paper, an innovative double rib sheet structure is proposed, which can replace the traditional rigid hinge joint with the surface contact. On the one hand, the variable camber wing structural design not only can improve the capacity to sustain more load but also will not increase the overall weight of the wing. On the other hand, it is a simple mechanical structure design to achieve the total wing camber change. Then the numerical simulation results show that the maximum stress at the connect of the wing rib is 88.2MPa, and the double ribs sheet engineering design meet the structural strength requirements. In addition, to make a fair comparison, the parameters of variable camber are fully referenced to the Talon Unmanned Aerial Vehicle (UAV. The results reveal that the total variable camber wing can further enhance aircraft flight efficiency by 29.4%. The design of the whole variable camber wing structure proposed in this paper has high engineering value and feasibility.
Hofman, Erwin; Halman, Johannes I.M.; van Looy, Bart
Architectural innovation is fundamental to the renewal of technological systems. However, it can be a real challenge to organize architectural innovation, all the more so when success hinges upon close collaboration with other firms that are responsible for different subsystems of the end product.
Tanimoto, Ryoji; Kikuchi, Toshiaki; Tanaka, Hirokazu; Amino, Masaki; Yanai, Minoru
Process and layout design of external wet gelation stages in vibropacking process was examined for the feasibility study of commercialized FBR cycle system. In this study, following process stages for the oxide core fuel production line were covered, that is, solidification, washing, drying, calcination, reduction, sintering stages including interim storage of sintering particles and reagent recovery stage. The main results obtained by this study are as follows: (1) Based on the process examination results conducted previously, process-flow, mass-balance and number of production line/equipment were clarified. The process is covered from the receive tank of feed solution to the interim storage equipment. Reagent recovery process-flow, mass-balance were also clarified. And preliminary design of the main equipment was reexamined. (2) Normal operation procedure and the procedure after process failure were summarized along with a remote automated operation procedure. Operation sequence of each production line was mapped out by using a time-chart. (3) Design outline of reagent recovery equipments, installed to recover waste liquid from the wet gelation stages in the view of environmental impact were examined. Effective techniques such as collection of solvent, residue waste treatment method were examined its applicability and selected. Schematic block diagram was presented. (4) Analytical items and analyzing apparatus were extracted taking into account of quality control and process management. Analytical sample taking position and frequency of sampling were also examined. (5) A schematic layout drawing of main manufacturing process and reagent recovery process was presented taking into account of material handling. (6) A feature of the operating rate at each process stage was examined by analyzing failure rate reliability of each component. applying the reliability-centred method. (RCM), the operating rate was evaluated and annual maintenance period was estimated using
Talke, K.S.S.; Salomo, S.; Lutz, A.; Wieringa, J.E.
In several industries, new products are very similar in functional features but compete on their unique design. Firms like Alessi, Apple, Bang & Olufsen, Dyson, or Kartell all follow a design-driven innovation approach and use their products' visual appearance as the main mean for differentiation.
Talke, K.S.S.; Salomo, S.; Lutz, A.; Wieringa, J.E.
In several industries, new products are very similar in functional features but compete on their unique design. Firms like Alessi, Apple, Bang & Olufsen, Dyson, or Kartell all follow a design-driven innovation approach and use their products' visual appearance as the main mean for differentiation.
Full Text Available Modelling a communication system in material culture today always involves with objects, people, organizations, activities and interrelationships among them. The researcher suggests bringing together stakeholders engaged to exchange ideas, which the interactions relate to multiple professions and disciplines in a participatory scope of communication system. Owing to the invention of digital media, the status quo of images and sounds has revolutionized and caused changes of the mode of art exhibitions that produce activities and aesthetic concepts in terms of numerical representation, modularity, automation, visual variability and transcoding. Underlying a participatory-design approach, the research emphasizes a co-creative meta-interpretation of museum‟s visitors. In addition, the research delves further into the use of new media-FleXpeaker™ [ITRI], as the carrier. Combining art and design with innovative technology, the research focuses on examining design objects and innovative material which are applied in new media art and exhibition, in the hope to find new angles of participatory interpretation of the “integrated innovation” in curating an exhibition.
Wakes, Sarah; Beukes, Amanda
The study reported in this paper adopted a holistic design approach to investigate issues associated with height related playground injuries from a users' perspective. The main objective was to gain an understanding of the relationship between height and fun so as to establish practical guidelines for addressing the causes of height related injuries whilst maintaining the attributes of playground equipment that children find fun and challenging. Results show that, on the one hand, the risk of injury increases when height is coupled with the use of upper body strength and, on the other hand, that coordination is a greater source of fun and challenge than height for children. Accordingly, it is suggested that the level of risk of injury attached to children's playground equipment can be reduced when the use of lower body strength and coordination are combined with lower free fall heights.
Full Text Available In the existing literature on innovation, financial services firms are attributed with a dependence on external knowledge inputs. Meanwhile, relative importance of sources of knowledge for innovation, modes of knowledge inflow, cooperation partners, advantages and disadvantages of cooperation for innovation remain underexplored. This study has unveiled that the most important internal sources of knowledge for innovation in financial services are frontline employees, new service development teams, bank executives, and backstage staff. Highly valuable modes of knowledge inflow for innovation are human resource development, purchase of equipment, and informal personal interactions. Financial services firms benefit from cooperation for innovation with external partners in the following aspects: increase in customer satisfaction, developed new skills of employees, new technologies, access to knowledge and expertise, decreased costs, and finding a new approach to solve a problem. Costs associated with external cooperation for innovation remain the most influential disadvantage of this mode of inbound open innovation.
The US Liquid Metal-Cooled Reactor (LMR) program has been restructured and is now focussed on the development of innovative plant designs which emphasize shorter construction times, increased use of passive, inherently safe features, cost-competitiveness with LWR plants, and minimization of safety-related systems. These changes have a considerable effect on the structural design aspects of the LMR plant. These structural problems and their solutions now under study form the main focus of this paper. (orig.)
This session will update therapeutic physicists on technological advancements and radiation oncology features of commercial CT, MRI, and PET/CT imaging systems. Also described are physicists’ roles in every stage of equipment selection, purchasing, and operation, including defining specifications, evaluating vendors, making recommendations, and optimal and safe use of imaging equipment in radiation oncology environment. The first presentation defines important terminology of CT and PET/CT followed by a review of latest innovations, such as metal artifact reduction, statistical iterative reconstruction, radiation dose management, tissue classification by dual energy CT and spectral CT, improvement in spatial resolution and sensitivity in PET, and potentials of PET/MR. We will also discuss important technical specifications and items in CT and PET/CT purchasing quotes and their impacts. The second presentation will focus on key components in the request for proposal for a MRI simulator and how to evaluate vendor proposals. MRI safety issues in radiation Oncology, including MRI scanner Zones (4-zone design), will be discussed. Basic MR terminologies, important functionalities, and advanced features, which are relevant to radiation therapy, will be discussed. In the third presentation, justification of imaging systems for radiation oncology, considerations in room design and construction in a RO department, shared use with diagnostic radiology, staffing needs and training, clinical/research use cases and implementation, will be discussed. The emphasis will be on understanding and bridging the differences between diagnostic and radiation oncology installations, building consensus amongst stakeholders for purchase and use, and integrating imaging technologies into the radiation oncology environment. Learning Objectives: Learn the latest innovations of major imaging systems relevant to radiation therapy Be able to describe important technical specifications of CT, MRI
Full Text Available As one of the effective ways of reducing the cost and increase the revenue, feeding dairy cows with individual precision in quantity could further develop the production potential of high- yield dairy cows and improve the milk yield of every dairy cow. Therefore, based on three kinds of technologies of radio frequency identification technology, wireless transmission technology and infrared technology and grounded on the foundation of previous studies, this thesis has completed the track- type equipment for feeding dairy cows with individual precision in quantity. The equipment takes the computer as the information management platform, adopts the singly chip microcomputer as the control platform, uses the wireless module and U disk to conduct the transmission of individual feeding data of dairy cows and guides the whole process with the track. This kind of equipment could advance automatically, identify and feed dairy cows precisely during the feeding process. This thesis also designs the matching feeding technology of the equipment, and accomplishes the test of feeding outside the cowshed, which takes “TMR + precise feeding with concentrated feed” as the feeding model, so that the feeding process could be more effective and further steady.
Windrum, P.; Frenken, K.; Green, Lawrence
The article addresses the role of ergonomic design in product innovation. Designers meet users’ needs by developing solutions to complex trade-offs—reverse salients—between a product’s characteristics. The fundamental ergonomic design challenge in portable computers concerns the reverse salient
Environmental experience can enhance the ideas of design students. Thus, this type of experience may interfere with the influence of design students' cognitive style on creativity. The aim of this study was to examine the influence of environmental experience on the relationship between innovative cognitive style and industrial design students'…
The results of the innovation competition, organised by the Interclima-Interconfort exhibition under the patronage of the Minister of equipment, transports and housing have been declared on the Monday eightieth of November 99 at Paris. Three medals have been awarded in each type of products and three flames reward the best innovations. These products are presented in this article: boilers, air-conditioning, tele-processing by Internet, software. (N.C.)
Robertson, Ted; Darling, Matthew; Leifer, Jennifer; Footer, Owen; Gordski, Dani
A deep understanding of human behavior is critical to designing effective health care delivery models, tools, and processes. Currently, however, few mechanisms exist to systematically apply insights about human behavior to improve health outcomes. Behavioral design teams (BDTs) are a successful model for applying behavioral insights within an organization. Already operational within government, this model can be adapted to function in a health care setting. To explore how BDTs could be applied to clinical care delivery and review models for integrating these teams within health care organizations. Interviews with experts in clinical delivery innovation and applied behavioral science, as well as leaders of existing government BDTs. BDTs are most effective when they enjoy top-level executive support, are co-led by a domain expert and behavioral scientist, collaborate closely with key staff and departments, have access to data and IT support, and operate a portfolio of projects. BDTs could be embedded in health care organizations in multiple ways, including in or just below the CEO’s office, within a quality improvement unit, or within an internal innovation center. When running a portfolio, BDTs achieve a greater number and diversity of insights at lower costs. They also become a platform for strategic learning and scaling.
Rama Mohan, S
Looming energy crisis, climate change concerns coupled with decreasing fossil fuel resources has garnered significant global attention toward development of alternative, renewable, carbon-neutral and eco-friendly fuels to fulfil burgeoning energy demands. Waste utilization and its management are being pursued with renewed interest due to the gamut of biobased products it can offer apart from providing enough energy to meet a major fraction of the world's energy demand. Biorefining is the sustainable processing of biomass into a spectrum of marketable products and energy. Integrating all components of waste treatment culminating into biobased products and energy recovery in a single integrated waste biorefinery is self sufficient, highly sustainable and is very beneficial. Designing systematic innovation policies are essential for development and commercialization of new technologies in this important futuristic research area. This communication explores Innovation Policy Road Mapping (IPRM) methodology available in the literature and applies it to design integrated waste biorefinery. Copyright © 2016 Elsevier Ltd. All rights reserved.
High-definition televisions should, by now, be a huge success. Philips, Sony, and Thompson invested billions of dollars to develop TV sets with astonishing picture quality. From a technology perspective, they've succeeded: Console manufacturers have been ready for the mass market since the early 1990s. Yet the category has been an unmitigated failure, not because of deficiencies, but because critical complements such as studio production equipment were not developed or adopted in time. Under-performing complements have left console producers in the position of offering a Ferrari in a world without gasoline or highways--an admirable engineering feat, but not one that creates value for customers. The HDTV story exemplifies the promise and peril of innovation ecosystems--the collaborative arrangements through which firms combine their individual offers into a coherent, customer-facing solution. When they work, innovation ecosystems allow companies to create value that no one firm could have created alone. The benefits of these systems are real. But for many organizations the attempt at ecosystem innovation has been a costly failure. This is because, along with new opportunities, innovation ecosystems also present a new set of risks that can brutally derail a firm's best efforts. Innovation ecosystems are characterized by three fundamental types of risk: initiative risks--the familiar uncertainties of managing a project; interdependence risks--the uncertainties of coordinating with complementary innovators; and integration risks--the uncertainties presented by the adoption process across the value chain. Firms that assess ecosystem risks holistically and systematically will be able to establish more realistic expectations, develop a more refined set of environmental contingencies, and arrive at a more robust innovation strategy. Collectively, these actions will lead to more effective implementation and more profitable innovation.
Full Text Available More and more business organizations recognize the relevance of sustainable innovations as driving factor for their corporate strategies, products and processes. But while the concept of sustainability is generally ratified by employees and consumers, their willingness to actually use or buy such innovations can be low. One of the most important facilitators for the adoption of innovations is self-experience generated by testing the innovation. This paper provides insight on how sustainable innovation testing affects consumer mindsets and which barriers consumers face when considering testing a sustainable innovation. The study draws on the data from an in-depth interview study with seven providers and consumers of electric cars (as sustainable innovation in business and private environments. Insights about the nature of consumer’s willingness to test are extracted and recommendations for the design and use of information systems as facilitators for testing sustainable innovations are derived.
Bongers, P.M.M.; Thullie, J.
Classically, when products have been developed at the bench, process engineers will search for equipment to manufacture the product at large scale. More than often, this search is constraint to the existing equipment base, or a catalog search for standard equipment. It is then not surprising, that
Herbaut, Alexis; Simoneau-Buessinger, Emilie; Barbier, Franck; Cannard, Francis; Guéguen, Nils
Footwear comfort is essential and pressure distribution on the foot was shown as a relevant objective measurement to assess it. However, asperities on the foot sides, especially the metatarsals and the instep, make its evaluation difficult with available equipment. Thus, a sock equipped with textile pressure sensors was designed. Results from the mechanical tests showed a high linearity of the sensor response under incremental loadings and allowed to determine the regression equation to convert voltage values into pressure measurements. The sensor response was also highly repeatable and the creep under constant loading was low. Pressure measurements on human feet associated with a perception questionnaire exhibited that significant relationships existed between pressure and comfort perceived on the first, the third and the fifth metatarsals and top of the instep. Practitioner Summary: A sock equipped with textile sensors was validated for measuring the pressure on the foot top, medial and lateral sides to evaluate footwear comfort. This device may be relevant to help individuals with low sensitivity, such as children, elderly or neuropathic, to choose the shoes that fit the best.
Alekseeva, Irina V.; Barsukova, Natalia I.; Pallotta, Valentina I.; Skovorodnikova, Nadia A.
This article proved the urgency of the problem of development of professional thinking of students studying design in modern conditions of higher education. The authors substantiate for the need of an innovative Blaise-method development of professional design thinking of students in higher education. "Blaise-method" named by us in…
Millery, Mari; Hall, Michelle; Eisman, Joanna; Murrman, Marita
Technology and distance learning can potentially enhance the efficient and effective delivery of continuing education to the public health workforce. Public Health Training Centers collaborate with instructional technology designers to develop innovative, competency-based online learning experiences that meet pressing training needs and promote best practices. We describe one Public Health Training Center's online learning module design process, which consists of five steps: (1) identify training needs and priority competencies; (2) define learning objectives and identify educational challenges; (3) pose hypotheses and explore innovative, technology-based solutions; (4) develop and deploy the educational experience; and (5) evaluate feedback and outcomes to inform continued cycles of revision and improvement. Examples illustrate the model's application. These steps are discussed within the context of design practices in the fields of education, engineering, and public health. They incorporate key strategies from across these fields, including principles of programmatic design familiar to public health professionals, such as backward design. The instructional technology design process we describe provides a structure for the creativity, collaboration, and systematic strategies needed to develop online learning products that address critical training needs for the public health workforce.
The Gamma heating value is an important factor needed for safety analysis of each experiments that will be realized on research reactor core. Gamma heat is internal heat source occurs in each irradiation facilities or any material irradiated in reactor core. This value should be determined correctly because of the safety related problems. The gamma heating value is in general depend on. reactor core characteristics, different one and other, and then each new reactor design should be completed by gamma heating data. The Innovative Research Reactor is one of the new reactor design that should be completed with any safety data, including the gamma heating value. For this reasons, calculation and analysis of gamma heating in the hole of reactor core and irradiation facilities in reflector had been done by using of modified and validated Gamset computer code. The result shown that gamma heating value of 11.75 W/g is the highest value at the center of reactor core, higher than gamma heating value of RSG-GAS. However, placement of all irradiation facilities in reflector show that safety characteristics for irradiation facilities of innovative research reactor more better than RSG-GAS reactor. Regarding the results obtained, and based on placement of irradiation facilities in reflector, can be concluded that innovative research reactor more safe for any irradiation used. (author)
Broek, T. van den; Giessen, A.M. van der
The goal of this study is to highlight possible future developments of importance to the electrical and optical (E&O) equipment sector, paying particular importance to ‘radical’ changes and discussing policy options and future scenarios. The electrical & optical equipment sector plays a vital role
Najm, Elie Michel
This work focuses on the design and implementation of an innovative residential PV system. In chapter one, after an introduction related to the rapid growth of solar systems' installations, the most commonly used state of the art solar power electronics' configurations are discussed, which leads to introducing the proposed DC/DC parallel configuration. The advantages and disadvantages of each of the power electronics' configurations are deliberated. The scope of work in the power electronics is defined in this chapter to be related to the panel side DC/DC converter. System integration and mechanical proposals are also within the scope of work and are discussed in later chapters. Operation principle of a novel low cost PV converter is proposed in chapter 2. The proposal is based on an innovative, simplified analog implementation of a master/slave methodology resulting in an efficient, soft-switched interleaved variable frequency flybacks, operating in the boundary conduction mode (BCM). The scheme concept and circuit configuration, operation principle and theoretical waveforms, design equations, and design considerations are presented. Furthermore, design examples are also given, illustrating the significance of the newly derived frequency equation for flybacks operating in BCM. In chapters 3, 4, and 5, the design implementation and optimization of the novel DC/DC converter illustrated in chapter 2 are discussed. In chapter 3, a detailed variable frequency BCM flyback design model leading to optimizing the component selections and transformer design, detailed in chapter 4, is presented. Furthermore, in chapter 4, the method enabling the use of lower voltage rating switching devices is also discussed. In chapter 5, circuitry related to Start-UP, drive for the main switching devices, zero-voltage-switching (ZVS) as well as turn OFF soft switching and interleaving control are fully detailed. The experimental results of the proposed DC/DC converter are presented in
This design report describes the NUS Preliminary Design of the Prototype Spent Nuclear Fuel Rod Consolidation Equipment for the Department of Energy. The sections of the report elaborate on each facet of the preliminary design. A concept summary is provided to assist the reader in rapidly understanding the complete design. The NUS Prototype Spent Fuel Rod Consolidation System is an automatically controlled system to consolidate a minimum of 750 MT (heavy metal)/year of US commercial nuclear reactor fuel, at 75% availability. The system is designed with replaceable components utilizing the latest state-of-the-art technology. This approach gives the system the flexibility to be developed without costly development programs, yet accept new technology as it evolves over the next ten years. Capability is also provided in the system design to accommodate a wide variety of fuel conditions and to recover from any situation which may arise
National Aeronautics and Space Administration — The overall objective of this multi-phase project is to explore, develop, integrate, and test several innovative structural design concepts and new material...
Siegel, Christine; Claydon, Jennifer
The current work seeks to explore University professors' perspectives on teaching and learning in an innovative classroom characterized by flexible design of space, furniture and technology. The study took place during the 2015-2016 academic year at Fairfield University, a Masters comprehensive university in the Northeastern United States.…
Reinders, Angelina H.M.E.; de Boer, Andries; de Winter, Arjan; Haverlag, Marco; Ossenbrink Sinke, W.; Helm, P.
This study covers the design of innovative product concepts based on a combination of PV and LED technology. The products were developed in a project that took place in 2008 and 2009 during a cooperation of the University of Twente with Philips Lighting. It is shown that surprisingly unpredictable -
NEA Today, 2001
Describes various innovations that have been developed to enhance education. These innovations include: helping educators help at-risk students succeed; promoting high school journalism; ensuring quality online learning experiences; developing a student performing group that uses theater to address social issues; and having students design their…
Costa, R. V.
Full Text Available Intellectual capital has for the past decades been evidenced as an important source of competitive advantages and differentiation at the firm level. At the same time, innovation has become a critical factor for companies to ensure their sustainability and even their survival in a globalized business landscape. Having in mind these two crucial concepts for business success, this study intends to build on the relationships between intellectual capital and product innovation at the firm level. Specifically, we will design and test a model based on the Analytic Hierarchy Process, whose aim is to allow the prioritization of intellectual capital elements according to their relative importance for product innovation performance at the firm level. The main goal of this research is to build a diagnosis and action tool that helps business managers incorporate an intellectual capital perspective into their product innovation initiatives. This framework will help managers to better understand which intellectual capital elements are more critical to their product innovation efforts, and thereby systematize actions and clarify resource allocation priorities to improve their product innovation capabilities. In order to validate the practicability of this proposal, the methodology was empirically applied to a Portuguese innovative company.
Fabio Héctor Giraldo Sánchez
Full Text Available Outlines the procedure for the design and construction of electric equipment for geophysical prospecting through electrical tomography method. The team is of average power, ensuring exploration depths quite suitable for applications and commercial and geotechnical studies. The device is essentially a DC voltage source of 500 volts that is able to provide a maximum current of 1 amp. It also contains a small charge current source of electrical currents counteract naturally found in the subsoil and are manifested as a difference in the surface potential. A general explanation of the geophysical method in question, helps to understand the basic principles of operation of the equipment and functions to be fulfilled. After building the team, we conducted a field data acquisition, in area near the town of Gachancipa Cundinamarca. The data from this equipment are processed with specialized software. The images obtained with the software presents the distributions of subsurface resistivity can be associated with the possible structures and geology of the study area.
The requirement of anti-earthquake design of nuclear power plants is getting severe year by year. The author will try to discuss how to control its severity and how to find a proper design procedure for licensing of new plants under such severe requirements. On the other hand we suffered from the enormous volumes of documents. To decrease such volumes, the format of documents should be standardized as well as the design procedure standardization. Starting from this point, we need the research and development on the following subjects: i) Standardization of design procedure. ii) Standardization of document. iii) Establishment of standard review procedure using computer. iv) Standardization of earthquake-resistant designed equipment. v) Standardization of anti-earthquake design procedure of piping systems. vi) Introducing margin evaluation procedure to design procedure. vii) Introducing proving test procedure of active component to design procedure. viii) Establishment of evaluation of human reliability in design, fabrication, inspection procedures. ix) Establishment of the proper relation of seismic trigger level and post-earthquake design procedures. (orig./HP)
Jones, A. S.; Horsburgh, J. S.; Matos, M.; Caraballo, J.
Networks conducting long term monitoring using in situ sensors need the functionality to track physical equipment as well as deployments, calibrations, and other actions related to site and equipment maintenance. The observational data being generated by sensors are enhanced if direct linkages to equipment details and actions can be made. This type of information is typically recorded in field notebooks or in static files, which are rarely linked to observations in a way that could be used to interpret results. However, the record of field activities is often relevant to analysis or post-processing of the observational data. We have developed an underlying database schema and deployed a web interface for recording and retrieving information on physical infrastructure and related actions for observational networks. The database schema for equipment was designed as an extension to the Observations Data Model 2 (ODM2), a community-developed information model for spatially discrete, feature based earth observations. The core entities of ODM2 describe location, observed variable, and timing of observations, and the equipment extension contains entities to provide additional metadata specific to the inventory of physical infrastructure and associated actions. The schema is implemented in a relational database system for storage and management with an associated web interface. We designed the web-based tools for technicians to enter and query information on the physical equipment and actions such as site visits, equipment deployments, maintenance, and calibrations. These tools were implemented for the iUTAH (innovative Urban Transitions and Aridregion Hydrosustainability) ecohydrologic observatory, and we anticipate that they will be useful for similar large-scale monitoring networks desiring to link observing infrastructure to observational data to increase the quality of sensor-based data products.
Ahmad Rifai; Usep Setia Gunawan; Indarzah Masbatin Putra
Based on a microcontroller, a stepper motor controller for brachy-therapy equipment has been designed and prototyped. The embedded control program routine and its other associated routines enable the microcontroller to generate required pulses via external commands for stepper motor based position control. The controller receives ASCII text command via a serial port. The constructed algorithm implements the widely used method that allows motor to rotate in three phases, i.e: acceleration, constant speed, and deceleration. (author)
Suchomel, R.R.; Stinton, D.P.; Preston, M.K.; Heck, J.L.; Bolfing, B.J.; Lackey, W.J.
Refabrication of HTGR fuels is a manufacturing process that consists of preparation of fuel kernels, application of multiple layers of pyrolytic carbon and silicon carbide, preparation of fuel rods, and assembly of fuel rods into fuel elements. All the equipment for refabrication of 233 U-containing fuel must be designed for completely remote operation and maintenance in hot-cell facilities. Equipment to remotely coated HTGR fuel particles has been designed and operated. Although not all of the equipment development needed for a fully remote coating system has been completed, significant progress has been made. The most important component of the coating furnace is the gas distributor, which must be simple, reliable, and easily maintainable. Techniques for loading and unloading the coater and handling microspheres have been developed. An engineering-scale system, currently in operation, is being used to verify the workability of these concepts. Coating crucible handling components are used to remove the crucible from the furnace, remove coated particles, and exchange the crucible, if necessary. After the batch of particles has been unloaded, it is transferred, weighed, and sampled. The components used in these processes have been tested to ensure that no particle breakage or holdup occurs. Tests of the particle handling system have been very encouraging because no major problems have been encountered. Instrumentation that controls the equipment performed very smoothly and reliably and can be operated remotely
Rieb, M.J.; Foley, R.S.
The Aerojet Manufacturing Company (AMCO) received a contract in November 1976 to provide consulting services in assisting Holmes and Narver, Incorporated with the conceptual designs, cost estimates, and schedules of equipment used to handle waste casks, to decontaminate waste canisters and to overpack damaged or highly contaminated waste canisters for the Waste Isolation Pilot Plant (WIPP). Also, the layout of the hot cell in which canister handling, overpack and decontamination takes place was to be reviewed along with the time and motion study of the cell operations. This report has been prepared to present the results of the efforts and contains all technical and planning data developed during the program. The contents of this report are presented in three sections: (1) comments on the existing design criteria, equipment conceptual designs, hot cell design and time and motion studies of projected hot cell activities; (2) design descriptions of the equipment concepts and justification for varying from the existing concept (if a variation occurred). Drawings of each concept are provided in Appendix A. These design descriptions and drawings were used as the basis for the cost estimates; and (3) schedule projections and cost estimates for the equipment described in Section 2. Detail cost estimate backup data is provided in Appendix B
Ana Laura Santos
Full Text Available This study focuses on the role of Systems Design in addressing the challenges of healthcare provision by international emergency relief organizations in developing countries. More specifically the challenges related to the safety and performance of medical equipment that is transferred in the aftermath of a humanitarian crisis. The aim of this paper is to describe the transfer of medical equipment and its associated challenges from a systems perspective and to reflect on the value of Systems Design as an approach to humanitarian innovation, addressing the identified systemic challenges. The concepts of Human Factors and Ergonomics, and Product-Service Systems will be presented as valuable contributions to support designers in handling a larger degree of complexity throughout the design process and to support them to make informed choices regarding this particular context.
Paloma, J. J.; Moraga, J. L.
From the beginning of its industrial activity 30 years ago, the Juzbado factory of Enusa Group has maintained a strong commitment to safety and technological innovation. As a result, we have development new equipment and constantly improving the existing ones, as well as the facilities of the factory in accordance with the internal procedures, with multidisciplinary design teams and review teams. (Author)
Zuber, Christi Dining; Moody, Louise
There is an increasing drive in health care for creativity and innovation to tackle key health challenges, improve quality and access, and reduce harm and costs. Human-centered design (HCD) is a potential approach to achieving organizational innovation. However, research suggests the nursing workforce feels unsupported to take the risks needed for innovation, and leaders may not understand the conditions required to fully support them. The aim of this study was to identify enabling conditions that support frontline nurses in their attempts to behave as champions of innovation and change. An HCD workshop was undertaken with 125 nurses employed in clinical practice at Kaiser Permanente. The workshop included empathy mapping and semistructured questions that probed participant experiences with innovation and change. The data were collated and thematic analysis undertaken through a Grounded Theory approach. The data were analyzed to identify key enabling conditions. Seven enablers emerged: personal need for a solution; challenges that have meaningful purpose; clarity of goal and control of resources; active experimentation; experiences indicating progress; positive encouragement and confidence; and provision of psychological safety. These enablers were then translated into pragmatic guidelines for leaders on how the tools of HCD may be leveraged for innovation and change in health care.
Yang, Myung Seung; Park, J.J.; Lee, J.W.; Kim, S.S.; Yim, S.P.; Kim, J.H.; Kim, K.H.; Na, S.H.; Kim, W.K.; Shin, J.M.; Lee, D.Y.; Cho, K.H.; Lee, Y.S.; Sohn, J.S.; Kim, M.J.
In this study, DUPIC powder and pellet fabrication equipment, welding system, QC equipment, and fission gas treatment are developed to fabricate DUPIC fuel at IMEF M6 hot cell. The systems are improved to be suitable for remote operation and maintenance with the manipulator at hot cell. Powder and pellet fabrication equipment have been recently developed. The systems are under performance test to check remote operation and maintenance. Welding chamber and jigs are designed and developed to remotely weld DUPIC fuel rod with manipulators at hot cell. Remote quality control equipment are being tested for analysis and inspection of DUPIC fuel characteristics at hot cell. And trapping characteristics is analyzed for cesium and ruthenium released under oxidation/reduction and sintering processes. The design criteria and process flow diagram of fission gas treatment system are prepared incorporating the experimental results. The fission gas treatment system has been successfully manufactured. (Author). 33 refs., 14 tabs., 91 figs
Wang, Paul T. [Mississippi State Univ., Mississippi State, MS (United States)
The Southern Regional Center for Lightweight Innovative Design (SRCLID) has developed an experimentally validated cradle-to-grave modeling and simulation effort to optimize automotive components in order to decrease weight and cost, yet increase performance and safety in crash scenarios. In summary, the three major objectives of this project are accomplished: To develop experimentally validated cradle-to-grave modeling and simulation tools to optimize automotive and truck components for lightweighting materials (aluminum, steel, and Mg alloys and polymer-based composites) with consideration of uncertainty to decrease weight and cost, yet increase the performance and safety in impact scenarios; To develop multiscale computational models that quantify microstructure-property relations by evaluating various length scales, from the atomic through component levels, for each step of the manufacturing process for vehicles; and To develop an integrated K-12 educational program to educate students on lightweighting designs and impact scenarios. In this final report, we divided the content into two parts: the first part contains the development of building blocks for the project, including materials and process models, process-structure-property (PSP) relationship, and experimental validation capabilities; the second part presents the demonstration task for Mg front-end work associated with USAMP projects.
Neutron and gamma radiation needs to be monitored in most nuclear installations since it is highly penetrating. On-line monitoring of these radiations is very important for the safe and controlled operation of nuclear reactors, accelerators etc. Several design innovations have been carried out on gas ionisation detectors such as boron-lined proportional counters and ion chambers, fission detectors, gamma ion chambers as well as self-powered detectors. The use of additional structures within boron-lined detectors has enhanced their neutron sensitivity without a corresponding increase in the unwanted gamma sensitivity. The neutron sensitivity of fission counters can be enhanced by designing them as transmission line devices. Ion chambers with two and six pairs of electrodes have been developed for monitoring pulsed x-ray background at accelerator areas. Ion chambers have been employed at gamma fields up to 80 kR/h by deriving the exposure levels on-line using microcontroller devices programmed on the basis of theoretical and empirical formulas. The use of gas electron multiplier foils is proposed for charge multiplication in ion chambers. Self-powered detectors with new emitter materials like Hi, Ni and Inconel have been developed. (author)
Seely, Kathryn A; Prather, Paul L; James, Laura P; Moran, Jeffery H
The principal psychoactive component of marijuana, Δ(9)-tetrahydrocannabinol (THC), activates CB1 cannabinoid receptors (CB1Rs). Unfortunately, pharmacological research into the design of effective THC analogs has been hampered by psychiatric side effects. THC-based drug design of a less academic nature, however, has led to the marketing of "synthetic marijuana," labeled as K2 or "Spice," among other terms, which elicits psychotropic actions via CB1R activation. Because of structural dissimilarity to THC, the active ingredients of K2/Spice preparations are widely unregulated. The K2/Spice "phenomenon" provides a context for considering whether marijuana-based drugs will truly provide innovative therapeutics or merely perpetuate drug abuse.
Patterson, P E
In our new global economy, biomedical product development teams need to be even more innovative in an environment constrained by fewer resources with less time from concept to market. Teams are often comprised of individuals spread around the world. To simulate this setting, we revised an existing course to incorporate teams of on-campus and distance students, with each team including both engineers and other specialties. Through interactive lectures and projects, we presented a systematic approach to innovation that should be useful to engineers and non-engineers alike. Students found the course challenging and exciting, displaying an improved ability to work in distributed teams and in developing innovative design solutions.
Hanafusa, A; Komeda, T; Ito, K; Zobel, P Beomonte
Project-based learning (PBL) is effective for developing human resources of young students. The design of welfare equipment, such as wheelchairs and gait assistive devices, is taken as the subject in this study because these devices must be fit to their environment, users, and method of use; students must consider the circumstances of each country concerned. The program commenced in 2012 at L'Aquila, Italy, and the Shibaura Institute of Technology, Japan and has been continuing for three years. Students were divided into four groups and discussions were held on how to adapt the equipment to the user and environment. After discussion, they designed and simulated a model of the equipment using CAD. Finally, they presented their designs to each other. Through the program, students had fruitful discussions, exchanged ideas from different cultures, and learned from each other. Furthermore, friendships among the students were nurtured. It is believed that the objective of the program was satisfactorily accomplished.
Bjarklev, Araceli; Kjær, Tyge; Andersen, Jan
into account to be able to achieve efficient reductions of energy and CO2 emissions and at the same time design a product attractive for the consumer, in terms of price, level of service and aesthetical demands, to ensure its strategic implementation. This paper takes the Danish office lighting sector......-psychological aspects such as consumers’ demands (aesthetic disposition, habits and different light tastes and needs). This is done by integrating relevant elements from eco-innovation and Service –Product System frameworks. Our empirical material is based on iterative interviews with relevant actors and experts within......Though there is broad consensus that one of the solutions to the current environmental challenge will be based on the use of low-carbon technologies, and even though there is a big potential to turn to a more sustainable design and innovation, there are several elements that need to be taken...
Pineiro, F.; Ho, K.; Khaial, A.; Boubcher, M.; Cottrell, C.; Kuran, S., E-mail: email@example.com [Candu Energy Inc., Mississauga, ON (Canada); Zhenhua, Z.; Zhiliang, M. [Third Qinshan Nuclear Power Company, Haiyan, Zhejiang (China)
The high neutron economy, on-power refuelling capability and fuel bundle design simplicity in CANDU reactors allow for the efficient utilization of alternative fuels. Candu Energy Inc. (Candu), in collaboration with the Third Qinshan Nuclear Power Company (TQNPC), the China North Nuclear Fuel Corporation (CNNFC), and the Nuclear Power Institute of China (NPIC), has successfully developed an advanced fuel called Natural Uranium Equivalent (NUE). This innovative design consists of a mixture of recycled and depleted uranium, which can be implemented in existing CANDU stations thereby bringing waste products back into the energy stream, increasing fuel resources diversity and reducing fuel costs. (author)
Pineiro, F.; Ho, K.; Khaial, A.; Boubcher, M.; Cottrell, C.; Kuran, S. [Candu Energy Inc., Mississauga, Ontario (Canada); Zhenhua, Z.; Zhiliang, M. [Third Qinshan Nuclear Power Co., Haiyan, Zhejiang (China)
The high neutron economy, on-power refuelling capability and fuel bundle design simplicity in CANDU® reactors allow for the efficient utilization of alternative fuels. Candu Energy Inc. (Candu), in collaboration with the Third Qinshan Nuclear Power Company (TQNPC), the China North Nuclear Fuel Corporation (CNNFC), and the Nuclear Power Institute of China (NPIC), has successfully developed an advanced fuel called Natural Uranium Equivalent (NUE). This innovative design consists of a mixture of recycled and depleted uranium, which can be implemented in existing CANDU stations thereby bringing waste products back into the energy stream, increasing fuel resources diversity and reducing fuel costs. (author)
Beamish, Julia O.; Ahn, Mira; Seiling, Sharon
Analysis of research on housing, equipment, and design (n=333) in the Journal of Home Economics/Journal of Family and Consumer Sciences (1985-2000), Home Economics Research Journal/Family and Consumer Sciences Research Journal (1985- 2000), and Housing and Society (1985-1999) found that articles declined by more than 50% and behavior theories were…
IV International scientific and technical conference “Innovative designs and technologies of nuclear power” has been organized and is conducted by JSC NIKIET with support from Rosatom State Corporation, the International Atomic Energy Agency, the Russian Academy of Sciences and the Nuclear Society of Russia. The conference topics include: innovative designs of nuclear facilities for various applications, nuclear fuel and new materials, closed fuel cycle technologies, SNF and RW management, technological answers to nonproliferation problems, small power reactors (stationary, transportable, floatable, propulsion, space), integrated codes of a new generation for safety analysis of nuclear power plants and fuel cycles, controlled fusion [ru
Behr, W.; Reisgen, U.
Since its establishment as nuclear research plant Juelich in the year 1956, the research centre Juelich (FZJ) is concerned with the material processing of special metals. Among those are, above all, the high-melting refractory metals niobium, molybdenum and tungsten. Electron beam welding has always been considered to be an innovative special welding method; in the FZJ, electron beam welding has, moreover, always been adapted to the increasing demands made by research partners and involved manufacturing and design sectors. From the manual equipment technology right up to highly modern multi-beam technique, the technically feasible for fundamental research has, this way, always been realised. (Abstract Copyright , Wiley Periodicals, Inc.) [de
Kana, D.D.; Pomerening, D.J.
The Research Program for Seismic Qualification of Nuclear Plant Electrical and Mechanical Equipment has spanned a period of three years and resulted in seven technical summary reports, each of which have covered in detail the findings of different tasks and subtasks, and have been combined into five NUREG/CR volumes. Volume 4 presents study of the use of fragility concepts in the design of nuclear plant equipment and compares the results of state-of-the-art proof testing with fragility testing
Hambrick, Marion E; Hums, Mary A; Bower, Glenna G; Wolff, Eli A
Elite athletes require the most advanced sports equipment to maintain their competitive edge, but manufacturers cannot always satisfy these athletes' specific equipment needs. Sport involvement can influence sports-equipment selections and is described as the process by which individuals rely on attitudes and belief systems to make sports-related consumption decisions. This study involved semistructured interviews with 5 elite Parasport athletes to identify and analyze the role of sport involvement in their selection of sports equipment. The results revealed that the athletes identified product limitations, created a collaborative environment, and promoted a culture of innovation to develop new sports products and address existing limitations. Theoretical and practical implications are discussed.
Mozin, I.V.; Vasil'ev, M.P.
Problems of developing systems for computer-aided design (CAD) of radioelectronic equipment for large electrophysical facilities such as charged particle accelerators of new generation are discussed. The PLATA subsystem representing a part of CAD and used for printed circuit design is described. The subsystem PLATA is utilized to design, on the average, up to 150 types of circuits a year, 100-120 of which belong to circuits of increased complexity. In this case labour productivity of a designer at documentation increases almost two times
Gomez S, R.A.; Rodriguez, T.J.
This thesis is about the sketch and construction of an equipment which samples contaminated gases in the air. The topic of this work, is to propose a solution for imported and national equipment. The solution consist on lower prices of imported and national equipment without loosing the accuracy and the precision of those now available. The investigation shows all process to sample gases and theirs measurement for which all the mechanical, electric and electronic equipment, and the necessary software for giving the results in a computerized way were outlined. With this work it was able to succeed in measurements with a national low price, accurate, reliable, programmable, completely automatic and easy to use. This equipment exceed in accuracy the Japanese and the american equipment
This accessible book presents unconventional technologies in heat exchanger design that have the capacity to provide solutions to major concerns within the process and power-generating industries. Demonstrating the advantages and limits of these innovative heat exchangers, it also discusses micro- and nanostructure surfaces and micro-scale equipment, and introduces pillow-plate, helical and expanded metal baffle concepts. It offers step-by-step worked examples, which provide instructions for developing an initial configuration and are supported by clear, detailed drawings and pictures. Various types of heat exchangers are available, and they are widely used in all fields of industry for cooling or heating purposes, including in combustion engines. The market in 2012 was estimated to be U$ 42.7 billion and the global demand for heat exchangers is experiencing an annual growth of about 7.8 %. The market value is expected to reach U$ 57.9 billion in 2016, and approach U$ 78.16 billion in 2020. Providing a valua...
Camarda, Charles J.
I believe we are facing a critical time where innovative engineering design is of paramount importance to the success of our aerospace industry. However, the very qualities and attributes necessary for enhancing, educating, and mentoring a creative spirit are in decline in important areas. The importance of creativity and innovation in this country was emphasized by a special edition of the Harvard Business Review OnPoint entitled: "The Creative Company" which compiled a series of past and present articles on the subject of creativity and innovation and stressed its importance to our national economy. There is also a recognition of a lack of engineering, critical thinking and problem-solving skills in our education systems and a trend toward trying to enhance those skills by developing K-12 educational programs such as Project Lead the Way, "Science for All Americans", Benchmarks 2061 , etc. In addition, with respect to spacecraft development, we have a growing need for young to mid-level engineers with appropriate experience and skills in spacecraft design, development, analysis, testing, and systems engineering. As the Director of Engineering at NASA's Johnson Space Center, I realized that sustaining engineering support of an operational human spacecraft such as the Space Shuttle is decidedly different than engineering design and development skills necessary for designing a new spacecraft such as the Crew Exploration Vehicle of the Constellation Program. We learned a very important lesson post Columbia in that the Space Shuttle is truly an experimental and not an operational vehicle and the strict adherence to developed rules and processes and chains of command of an inherently bureaucratic organizational structure will not protect us from a host of known unknowns let alone unknown unknowns. There are no strict rules, processes, or procedures for understanding anomalous results of an experiment, anomalies with an experimental spacecraft like Shuttle, or in the
Lister, Cameron; Payne, Hannah; Hanson, Carl L; Barnes, Michael D; Davis, Siena F; Manwaring, Todd
Public health enjoyed a number of successes over the twentieth century. However, public health agencies have arguably been ill equipped to sustain these successes and address the complex threats we face today, including morbidity and mortality associated with persistent chronic diseases and emerging infectious diseases, in the context of flat funding and new and changing health care legislation. Transformational leaders, who are not afraid of taking risks to develop innovative approaches to combat present-day threats, are needed within public health agencies. We propose the Public Health Innovation Model (PHIM) as a tool for public health leaders who wish to integrate innovation into public health practice. This model merges traditional public health program planning models with innovation principles adapted from the private sector, including design thinking, seeking funding from private sector entities, and more strongly emphasizing program outcomes. We also discuss principles that leaders should consider adopting when transitioning to the PHIM, including cross-collaboration, community buy-in, human-centered assessment, autonomy and creativity, rapid experimentation and prototyping, and accountability to outcomes.
Full Text Available Public health enjoyed a number of successes over the twentieth century. However, public health agencies have arguably been ill equipped to sustain these successes and address the complex threats we face today, including morbidity and mortality associated with persistent chronic diseases and emerging infectious diseases, in the context of flat funding and new and changing health care legislation. Transformational leaders, who are not afraid of taking risks to develop innovative approaches to combat present-day threats, are needed within public health agencies. We propose the Public Health Innovation Model (PHIM as a tool for public health leaders who wish to integrate innovation into public health practice. This model merges traditional public health program planning models with innovation principles adapted from the private sector, including design thinking, seeking funding from private sector entities, and more strongly emphasizing program outcomes. We also discuss principles that leaders should consider adopting when transitioning to the PHIM, including cross-collaboration, community buy-in, human-centered assessment, autonomy and creativity, rapid experimentation and prototyping, and accountability to outcomes.
Ahrensbach Rasmussen, Klement
The topics of business model innovation (BMI) and organizational design have potentially important links. And yet, there has been little cross-fertilization of ideas between the two fields. The purpose of this thesis is to fill that gap by proposing and developing an organizational view of BMI...... that focuses on the missing links between business model innovation and organizational design theory. Guided by the research question—what is the role of organizational design in the process of business model innovation?—the thesis not only investigates how BMI activity unfolds, but also looks at the different...... roles of the firm’s organizational design and where the activity takes place. Moreover, this research provides ample detail on how organizational complementarities emerge or vanish as a result of the fit or misfit between business model elements and design choices. To drive home these important points...
Wu, Xiaoli; Qiu, Tingting; Chen, Huijuan
As children mature, bike products for children in the market develop at the same time, and the conditions are frequently updated. Certain problems occur when using a bike, such as cycle overlapping, repeating function, and short life cycle, which go against the principles of energy conservation and the environmental protection intensive design concept. In this paper, a rational multi-function method of design through functional superposition, transformation, and technical implementation is proposed. An organic combination of frog-style scooter and children's tricycle is developed using the multi-function method. From the ergonomic perspective, the paper elaborates on the body size of children aged 5 to 12 and effectively extracts data for a multi-function children's bike, which can be used for gliding and riding. By inverting the body, parts can be interchanged between the handles and the pedals of the bike. Finally, the paper provides a detailed analysis of the components and structural design, body material, and processing technology of the bike. The study of Industrial Product Innovation Design provides an effective design method to solve the bicycle problems, extends the function problems, improves the product market situation, and enhances the energy saving feature while implementing intensive product development effectively at the same time.
Tuzovic, Sven; Wirtz, Jochen; Heracleous, Loizos Th.
Purpose – How can some companies be the innovation leader in their industry over prolonged periods of time, while others cannot? The purpose of this study is to understand a firm’s capability to be a successful serial innovator and to generate a constant stream of industry-leading innovations.\\ud \\ud Design/Methodology/Approach – The paper uses a longitudinal case study approach to gain an understanding of what and how Singapore Airlines (SIA) sustained service innovation for over 30 years. T...
de Ana, F J; Umstead, K A; Phillips, G J; Conner, C P
The innovation process has often been represented as a linear process which funnels customer needs through various business and process filters. This method may be appropriate for some consumer products, but in the medical device industry there are some inherent limitations to the traditional innovation funnel approach. In the medical device industry, there are a number of stakeholders who need to have their voices heard throughout the innovation process. Each stakeholder has diverse and unique needs relating to the medical device, the needs of one may highly affect the needs of another, and the relationships between stakeholders may be tenuous. This paper describes the application of a spiral innovation process to the development of a medical device which considers three distinct stakeholder voices: the Voice of the Customer, the Voice of the Business and the Voice of the Technology. The process is presented as a case study focusing on the front-end redesign of a class III medical device for an orthopedics company. Starting from project initiation and scope alignment, the process describes four phases, Discover, Envision, Create, and Refine, and concludes with value assessment of the final design features.
Full Text Available This article describes a first step towards a strategy for using living labs as a means to foster innovation and develop new concepts of sustainable living from an architectural point of view. The overall aim is to enable truly sustainable living through radically reduced energy and resource use thus addressing both environmental and social aspects of sustainability. Earlier research has shown that contemporary housing developments, including those with a sustainable profile, do not profoundly question modern lifestyles and consumption, which is a necessity to overcome limitations of a technological focus on environmental efficiency in construction. Thus, we see an opportunity for the discipline of architecture to engage in current investments in living lab facilities in order to push innovation in the field of sustainable housing. We introduce the concept of a "Habitation Lab", which will provide an arena for radical and high-risk design experimentation between users, building-sector actors, and academia, and we describe a case study of a planned Habitation Lab within a living lab facility where traditional solutions for daily living and habitation are questioned and new architectural innovations are explored and evaluated. The idea of using experimental activities in the field of housing is not new, and we argue that new investments should build on earlier experiences to avoid perpetuating misconceptions and repeating past failures. Furthermore, to ensure the dissemination and uptake of results, the design of the Habitation Lab should consider the innovation and learning trajectories of the building sector. We propose a transdisciplinary setting to provide a neutral arena for value creation and to increase the distribution of experiences.
Usher, D.M.; Cox, G.A.
The basic equations important in the design of rf sputtering equipment are presented. Attention is restricted to the 'disc and annulus' system and simple techniques in lead-through fabrication and electrode shielding are described. Also rf power oscillator theory is used to derive the important parameters of power generation. Load coupling and power matching techniques are discussed. Problems of the magnetic field coil design are analysed and a value for the thermal conductivity of coils wound from polyurethane coated wire is given, namely k = 0.64 W m -1 / 0 C -1 , permitting the steady state temperature distribution inside such coils to be predicted. (author)
The Continuous Electron Beam Accelerator Facility (CEBAF) will be dedicated to basic research in Nuclear Physics using electrons and photons as projectiles. The accelerator configuration allows three nearly continuous beams to be delivered simultaneously in three experimental halls, which will be equipped with complementary sets of instruments: Hall A--two high resolution magnetic spectrometers; Hall B--a large acceptance magnetic spectrometer; Hall C--a high-momentum, moderate resolution, magnetic spectrometer and a variety of more dedicated instruments. This report contains a short description of the initial complement of experimental equipment to be installed in each of the three halls.
Castillo, Jose M.; Dorman, Clark; Gaunt, Brian; Hardcastle, Beth; Justice, Kelly; March, Amanda L.
Schools across the nation are implementing innovative practices; however, questions remain regarding how to facilitate quality implementation. Research designs that emphasize high degrees of control over independent variables result in findings with internal validity, but that may not generalize to complex, dynamic educational systems. The purpose…
Synthetic biology requires both engineering efficiency and compliance with safety guidelines and ethics. Focusing on the rational construction of biological systems based on engineering principles, synthetic biology depends on a genome-design platform to explore the combinations of multiple biological components or BIO bricks for quickly producing innovative devices. This chapter explains the differences among various platform models and details a methodology for promoting open innovation within the scope of the statutory exemption of patent laws. The detailed platform adopts a centralized evaluation model (CEM), computer-aided design (CAD) bricks, and a freemium model. It is also important for the platform to support the legal aspects of copyrights as well as patent and safety guidelines because intellectual work including DNA sequences designed rationally by human intelligence is basically copyrightable. An informational platform with high traceability, transparency, auditability, and security is required for copyright proof, safety compliance, and incentive management for open innovation in synthetic biology. GenoCon, which we have organized and explained here, is a competition-styled, open-innovation method involving worldwide participants from scientific, commercial, and educational communities that aims to improve the designs of genomic sequences that confer a desired function on an organism. Using only a Web browser, a participating contributor proposes a design expressed with CAD bricks that generate a relevant DNA sequence, which is then experimentally and intensively evaluated by the GenoCon organizers. The CAD bricks that comprise programs and databases as a Semantic Web are developed, executed, shared, reused, and well stocked on the secure Semantic Web platform called the Scientists' Networking System or SciNetS/SciNeS, based on which a CEM research center for synthetic biology and open innovation should be established. Copyright © 2011 Elsevier Inc
This deliverable is for Task 9, Mixed Alcohols from Syngas: State of Technology, as part of National Renewable Energy Laboratory (NREL) Award ACO-5-44027, ''Equipment Design and Cost Estimation for Small Modular Biomass Systems, Synthesis Gas Cleanup and Oxygen Separation Equipment''. Task 9 supplements the work previously done by NREL in the mixed alcohols section of the 2003 technical report Preliminary Screening--Technical and Economic Assessment of Synthesis Gas to Fuels and Chemicals with Emphasis on the Potential for Biomass-Derived Syngas.
Katerndahl, David; Crabtree, Benjamin
PURPOSE Addressing important but complex research questions often necessitates the creation of innovative mixed methods designs. This report describes an approach to developing research designs for studying important but methodologically challenging research questions. METHODS The Methodological Think Tank has been held annually in conjunction with the Primary Care Research Methods and Statistics Conference in San Antonio since 1994. A group of 3 to 4 methodologists with expertise balanced between quantitative and qualitative backgrounds is invited by the think tank coordinators to serve on a 2-day think tank to discuss a research question selected from those submitted in response to a call for proposals. During the first half-day, these experts explore the content area with the investigator, often challenging beliefs and assumptions. During the second half-day, the think tank participants systematically prune potential approaches until a desirable research method is identified. RESULTS To date, the most recent 7 think tanks have produced fundable research designs, with 1 being funded by a K award and 4 by R01 grants. All participating investigators attributed much of their success to think tank participation. Lessons learned include (1) the importance of careful selection of participating methodologists, (2) all think tank communities of inquiry must go through 4 stages of development from pseudocommunity to community, and (3) the critical importance of listening by the investigator. CONCLUSION Researchers and academic departments could use this process locally to develop innovative research designs. PMID:17003146
Full Text Available Purpose. Development of innovative electrical engineering discipline «Electric Machines in Mechatronic Systems» in order to improve the training of specialists of electrical engineering specialty. Methodology. The proposed project concerns the educational reforms that promote the intensification of the educational process. Results. The structure of interactive educational and training complex, which is a computer learning tool in the form of software and methodical support, as well as data and knowledge bases and consists of functionally related multimedia learning systems, interactive learning, automated control of the learning process. Originality. To offer online training and research facilities, guidelines for laboratory and computational and graphic works. Practical value. Increase the knowledge of students of educational material related to the discipline of innovation «Electric Machines in Mechatronic Systems».
Rafferty, Kevin D.
The performance evaluation of space heating equipment for a geothermal application is generally considered from either of two perspectives: (a) selecting equipment for installation in new construction, or (b) evaluating the performance and retrofit requirements of an existing system. With regard to new construction, the procedure is relatively straightforward. Once the heating requirements are determined, the process need only involve the selection of appropriately sized hot water heating equipment based on the available water temperature. It is important to remember that space heating equipment for geothermal applications is the same equipment used in non-geothermal applications. What makes geothermal applications unique is that the equipment is generally applied at temperatures and flow rates that depart significantly from traditional heating system design. This chapter presents general considerations for the performance of heating equipment at non-standard temperature and flow conditions, retrofit of existing systems, and aspects of domestic hot water heating.
Park, J. W.; Kim, M. Y.; Han, K. T.; Park, J. D.
There has not been a strict regulatory requirements for the Equipment Qualification(EQ) in 1970's when Kori Unit 1 had begun the construction and the commercial operation. The Korean regulatory body requested the EQ on the various safety-related components, as a result of Periodic Safety Review. However, the EQ itself is impossible in some areas, due to the high pressure/temperature and flooding environment conditions from the pipe breaks. Design modification is being considered in the Auxiliary Building, the Intermediate Building, the Component Cooling Water Heat Exchanger Building and the Turbine Building, in order to mitigate the environmental conditions for the EQ
The aim of this paper is to discuss the first results and methodological challenges and perspectives of designing game-inspired scenarios for implementation of innovation processes into schools' science education. This paper comprises and report on a case study of a game-inspired innovation...... scenario designed for technology education in grades 7 - 9 in Danish schools. In the paper, methodological challenges of doing design-based research into technology innovation education are discussed. The preliminary results from the first studies of a game-inspired technology innovation camp are also...... presented, along with discussions of the future of development of these educational spaces....
Jalali, H.R.; Fadaei, A.H.
Highlights: • An innovative and safe design for grid plate in research reactors proposed. • New grid plate acts as an independent shutdown system. • Neutronic and transient calculation was done using MTR-PC package. • Calculations show that the performance and safety of new design are acceptable. - Abstract: The purpose of this paper is to propose an innovative and safe design of grid plate for Tehran research reactor (TRR) without any reduction in its performance in comparison with the current operation. The new grid plate consisted of two joined cubic with empty walls which are place of fuels and heavy water, respectively. The proposed design is such that the reactor core is divided into two distinct parts using the heavy water. The heavy water is inserted in the walls of the new grid plate. The new design of grid plate by keeping the characteristics of the previous version creates the possibility of shutting the reactor down in critical condition. In this paper, at initial step, a simulation of acceptable benchmark for Tehran research reactor is performed which could be considered reliable and comparable with SAR (Safety Analysis Report) data. In the next step, two different designs are proposed for grid plate and then are applied to reactor core using simulation tools. For the proposed design: core excess reactivity, shutdown margin, control rod worth, neutron flux and kinetic parameters are calculated. Furthermore, the transient analysis was performed for the new design to check the status of reactor safety. Obtained results show that all neutronic parameters for the first operating core and the new design are comparable, and there is no reduction in the efficiency of reference core. Moreover, in the current design, a diverse and independent shutdown system for TRR was included. Nuclear reactor analysis codes including MTR-PC package were employed to carry out these calculations.
A. I. Kotlabay; V. A. Korobkin; V. F. Tamelo; I. V. Kostko; S. V. Kondratiev
Study of directions concerning development of military equipment, its modernization with the purpose to improve its military efficiency is an actual problem for the Armed Forces, military science, designers and researchers.The paper analyzes and estimates possibilities to use civil equipment for military purpose. Problems pertaining to technologies of double application, diversification of civil equipment in military engineering machinery are considered in the paper.
Nitrocellulose film and converter screens used for neutron radiography are described. Difficulties in visualization of radiographs on those films are mentioned. Because there is no equipment for etching nitrocellulose film available on the market Risoe has designed and produced such equipment at an estimated cost of Dkr. 15,000. Design criteria for this equipment are given and its performance described
Full Text Available the design of trackless mining equipment (TME) is poor, with improvised seating, poor cabin layouts and sub-standard display instrumentation. This paper will present the key findings of two studies assessing ergonomics risk factors associated with automated...
Yagodkin, F. I.; Prokopov, A. Y.; Pleshko, M. S.; Pankratenko, A. N.
The article deals with the modern problems of construction and reconstruction of vertical shafts of mines, which require innovative technical solutions in the mechanization of mining operations. The examples developed by the authors of the original equipment and technologies, are successfully implemented for the mining industry in Russia.
Blissell, W.H.; Ciez, A.P.; Goedicke, F.E.; Bessko, C.
This document describes the Westinghouse Final Design for the Prototypical Spent Fuel Consolidation Equipment Demonstration Project. This design represents a fully qualified, licensable, cost effective spent fuel rod consolidation system. As a result of significant concerns raised by DOE and its Technical Review Committee during the 30% Design Review, significant changes were made to the original Preliminary Design resulting from Phase I activities. These changes focused on increased automation, end fitting removal, the rod pulling process and the need to maintain the consolidation canisters as clean as possible. As a result of these changes, the new system is greatly enhanced with a much greater probability of meeting or exceeding the project functional requirements. As a result of delays in resolving cost and contractual differences, additional bench testing was not conducted during Phase II. It is however our belief that the current design exceeds the 90% confidence level required by DOE because of the confidence gained from the Phase I tests, the additional engineering detail completed and the fact that our rod pulling tool has been demonstrated in a similar application at Oconee while our ID tube cutter is a modified (mounting method only) off-the-shelf design. 7 refs., 49 figs., 36 tabs
Rubick, R.D.; Stevens, W.W.; Burke, L.L.
Although vacuum pumps on continuous air monitors (CAMs) do not produce noise levels above regulatory limits, engineering controls were used to establish a safer work environment. Operations performed in areas where CAMs are located are highly specialized and require precision work when handling nuclear materials, heavy metals, and inert gases. Traditional methods for controlling noise such as enclosing or isolating the source and the use of personal protection equipment were evaluated. An innovative solution was found by retrofitting CAMs with air powered multistage ejectors pumps. By allowing the air to expand in several chambers to create a vacuum, one can eliminate the noise hazard altogether. In facilities with adequate pressurized air, use of these improved ejector pumps may be a cost-effective replacement for noisy vacuum pumps. A workplace designed or engineered with noise levels as low as possible or as close to background adds to increased concentration, attention to detail, and increased production
Mobach, Mark P.; Nardelli, Giulia; Konkol, Jennifer
Purpose : To report in FM Innovation. Theory : Innovation theory, service management, space design. Design/methodology/approach : Case studies, workshop. Findings : Barriers, areas of interest, and best practices in FM Innovation. Originality/value : Presents a first exploration of European case...
Mobach, Mark P.; Nardelli, Giulia; Konkol, Jennifer; Kok, Herman B.; Alexander, Keith; Alexander, Keith; Price, Ilfryn
Purpose: To report in FM Innovation. Theory: Innovation theory, service management, space design. Design/methodology/approach: Case studies, workshop. Findings: Barriers, areas of interest, and best practices in FM Innovation. Originality/value: Presents a first exploration of European case
Haase, Louise Møller; Laursen, Linda Nhu
Designing a remarkable product innovation is a difficult challenge, which businesses today continuously are striving to tackle. This challenge is particularly present in the early phase of innovation, where the main product concept and frames of the innovation is determined. As a main challenge...... in the early phase is the reasoning process; innovation team are faced with open- ended ill-defines problems, where they need to make decisions about an unknown future having only incomplete, ambiguous and contradicting insights available. We study the reasoning of experts, how they frame to make sense of all...... the insights and create a basis for decision making in relation to a new project. Based on case studies of five innovative products from various industries, we suggest a Product Reasoning Model for understanding reasoning and envisioning of new product innovations in the early phases of innovation....
Ljiljana Stošić Mihajlović
Full Text Available The company "Simpo" – Vranje, is the largest exporter of Serbian furniture and more than four decades has been present on the international market, in almost every continent. And today in about 30 countries worldwide exports 65% of production. Its main advantages are a business emphasis on modern design, the constant innovation of products and materials, and personalization.
Wintjes, R.J.M.; Douglas, D.; Fairburn, J.; Hollanders, H.J.G.M.; Pugh, G.
Innovation support measures in the EU are mostly designed to support product innovation in R&D intensive sectors. To increase the still considerable contribution to regional employment and competitiveness from SMEs in traditional manufacturing industries a broader innovation (policy) mix is more
Purpose of this report: This report was prepared for RISO team involved in design of the innovation system Report provides innovation methodology to establish common understanding of the process concepts and related terminology The report does not includeRISO- or Denmark-specific cultural, econom...
Szymanski, J.; Frimpong, S.; Sobieski, R. [Alberta Univ., Edmonton, AB (Canada). Centre for Advanced Energy and Minerals Research
This presentation described the fundamental and applied research work which has been carried out at the University of Alberta's Centre for Advanced Energy and Minerals Research to improve the undercarriage elements of large scale earthmoving equipment used in oil sands mining operations. A new method has been developed to predict the optimum curvature and blade geometry of earth moving equipment such as bulldozers and motor graders. A mathematical relationship has been found to approximate the optimum blade shape for reducing cutting resistance and fill resistance. The equation is a function of blade geometry and soil properties. It is the first model that can mathematically optimize the shape of a blade on earth moving equipment. A significant saving in undercarriage components can be achieved from reducing the amount of cutting and filling resistance for this type of equipment working on different soils. A Sprocket Carrier Roller for a Tracked Vehicle was also invented to replace the conventional cylindrical carrier roller. The new sprocket type carrier roller offers greater support for the drive track and other components of the undercarriage assembly. A unique retaining pin assembly has also been designed to detach connecting disposable wear parts from earthmoving equipment. The retaining pin assembly is easy to assemble and disassemble and includes reusable parts. 13 figs.
Borrás, Susana; Edquist, Charles
The purpose of this article is to discuss the different types of instruments of innovation policy, to examine how governments and public agencies in different countries and different times have used these instruments differently, to explore the political nature of instrument choice and design (and...... associated issues), and to elaborate a set of criteria for the selection and design of the instruments in relation to the formulation of innovation policy. The article argues that innovation policy instruments must be designed and combined into mixes in ways that address the problems of the innovation system....... These mixes are often called “policy mix”. The problem-oriented nature of the design of instrument mixes is what makes innovation policy instruments ‘systemic’....
Borrás, Susana; Edquist, Charles
The purpose of this article is to discuss the different types of instruments of innovation policy, to examine how governments and public agencies in different countries and different times have used these instruments differently, to explore the political nature of instrument choice and design (and...... associated issues), and to elaborate a set of criteria for the selection and design of the instruments in relation to the formulation of innovation policy. The article argues that innovation policy instruments must be designed and combined into mixes in ways that address the problems of the innovation system....... These mixes are often called “policy mix”. The problem-oriented nature of the design of instrument mixes is what makes innovation policy instruments ‘systemic’....
Selvam, Pagandai V. Pannir; Santiago, Brunno Henrique de S. [Universidade Federal de Alagoas (UFAL), Maceio, AL (Brazil)], email: firstname.lastname@example.org; Almeida, Louizy Minora C.A. de; Israel, Samy B.S. [Universidade Federal do Rio Grande do Norte (DEQ/CT/UFRN), Natal, RN (Brazil). Centro de Tecnologia. Dept. de Engenharia Quimica
Brazil is the leader known for its ethanol biofuel development, but also for biomass charcoal, yet lacks in clean rural biofuel production. This paper deals with the system design for sustainable rural projects developments based on the the bioenergy production from biomass wastes using Innovative process equipment design and the process optimization. With the economic objective towards sustainable clean small scale rural energy production, and also the co-production of hot, cold thermal energy, at first, several preliminary projects had been developed and analysed. Then, a detailed project engineering and the results on economical viability were obtained. The dynamic material, energy and cash flow models of the complex integrated food processing and small scale energy productions, were at first constructed using excel electronic spread sheet for Windows. Computer aided system for process modeling and simulation using SUPERPRO, Intelligent Inc. Economic feasibilities studies using genetics algorithms are under developments. The preliminary analysis of cost and investments of the the integrated biomass utilisation projects which are included for this study are: biological aerobic treatment process, methane gas production using anaerobic digestion process, aerobic composting, drying of tropical fruits, effluent treatments, biogas and syngas production as well as cogeneration of energy production for drying and cooling using biogas. These models allowed us the identification of tech economical and scale up problems. The results obtained with several preliminary project development with few case studies are reported for integrated project developments for fuel and food using process and cost simulation models. Several economic problems related with implementation of the small scale rural energy system for sustained local developments based on tropical fruit producing rural areas are analysed and a concept of the integrated bio system for micro enterprise has been
Zhang Jingyu; Yin Xiaozhan
Rabbeted capping plates are widely used in the roof of equipment cells in order to meet the requirements of nuclear radiation protection. The key considerations in the design include vertical load, seismic load and repair load. This article establishes T shaped and Z-shaped plate model via FEM software (ANSYS), analyzes the bearing capacity and displacement distribution in different load cases, and provides recommendations to the design and construction accordingly. (authors)
Zhong, Hairong; Xu, Wei; Hu, Haojun; Duan, Chengfang
This article analyzes the features of fostering optoelectronic students' innovative practical ability based on the knowledge structure of optoelectronic disciplines, which not only reveals the common law of cultivating students' innovative practical ability, but also considers the characteristics of the major: (1) The basic theory is difficult, and the close combination of science and technology is obvious; (2)With the integration of optics, mechanics, electronics and computer, the system technology is comprehensive; (3) It has both leading-edge theory and practical applications, so the benefit of cultivating optoelectronic students is high ; (4) The equipment is precise and the practice is costly. Considering the concept and structural characteristics of innovative and practical ability, and adhering to the idea of running practice through the whole process, we put forward the construction of three-dimensional innovation and practice platform which consists of "Synthetically Teaching Laboratory + Innovation Practice Base + Scientific Research Laboratory + Major Practice Base + Joint Teaching and Training Base", and meanwhile build a whole-process progressive training mode to foster optoelectronic students' innovative practical ability, following the process of "basic experimental skills training - professional experimental skills training - system design - innovative practice - scientific research project training - expanded training - graduation project": (1) To create an in - class practical ability cultivation environment that has distinctive characteristics of the major, with the teaching laboratory as the basic platform; (2) To create an extra-curricular innovation practice activities cultivation environment that is closely linked to the practical application, with the innovation practice base as a platform for improvement; (3) To create an innovation practice training cultivation environment that leads the development of cutting-edge, with the scientific
Rahmat; Budi Santoso; Krismawan; Abdul Jalil
Mechanical design for positioning of GM detector system has been done. It is used for avian flu detection equipment. The requirements for the design are to protect detection system against shock, portable, and easy to maintain. The mechanical system consists of connectors, cable assemblies, holders, casing, housing and detectors cover. The selected material should have small gamma radiation absorption property in order to give optimum counts for the detector. The design result should give a system that is easy to operate, cheap and easy to assemble. (author)
Spyropoulos, B; Tzavaras, A; Zogogianni, D; Botsivaly, M
The purpose of this paper is to present the design and the current development status of an Anesthesia Information Management System (AIMS). For this system, the physical and technical advances, depicted in relevant, recently published Industrial Property documents, have been taken into account. Additional innovative sensors create further data-load to be managed. Novel wireless data-transmission modes demand eventually compliance to further proper standards, so that interoperability between AIMS and the existing Hospital Information Systems is being sustained. We attempted to define, the state-of-the-art concerning the functions, the design-prerequisites and the relevant standards and of an "emerging" AIMS that is combining hardware innovation, real-time data acquisition, processing and displaying and lastly enabling the necessary interoperability with the other components of the existing Hospital Information Systems. Finally, we report based on this approach, about the design and implementation status, of our "real-world" system under development and discuss the multifarious obstacles encountered during this still on-going project.
Vujovic, Sladjana; Ulhøi, John Parm
Purpose - The aim of this paper is to investigate the role of online networking during the innovation process, including its role(s) in communication, cooperation and coordination. The paper neither implicitly assumes that online computer-based networking is a prerequisite for the innovation...... process nor denies the possibility that innovation can emerge and successfully survive without it. It merely presupposes that, in cases of innovation where information and communication technologies play a substantial role, non-proprietarity may offer an interesting alternative to innovations based...... on proprietary knowledge. Design/methodology/approach - The paper borrows from the theory of communities-of-practice, which takes into account social relations, contacts, and the transfer and incorporation of knowledge. Open source innovation is not the exclusive preserve of computer nerds, but also has...
Thuesen, Christian Langhoff; Jespersen, Kristina Risom
. Furthermore will an idea space collect and rate ideas from the users. Through a combination of technical and user driven innovation the design community will act as a learning tool for the users and producers and thereby facilitate the development of a market for sustainable homes.......This paper presents a development project which aims to create a market place for sustainable homes – around a design community where the uses and producers collectively can develop new energy efficient solutions and thereby reduce the emmisson of CO2. The core functionality of the design community...... is a configurator where the users based on the produceres templates can design their own home at a selected address visualizing and estimating the energy consumption, total cost, CO2 emission etc. All the designs will be collected and rated in a design space creating transparency over the market and technologies...
Full Text Available The punk movement is an example of peripheral culture that currently influences the dominant culture. This article aims to point out what were the changes and the innovations that the punk graphic design had to struggle to adapt itself to the series Peter Punk, exhibited by Disney XD channel. Through literature review and analysis of images, it is possible to conclude that the show’s graphic design absorbed the punk style with other influences, but without the spontaneity of punk.
Nelson, Julien; Buisine, Stéphanie; Aoussat, Améziane
Anticipation of future product use is a persistent issue in User-Centered Design. In this paper, we argue that one obstacle to early integration of use analysis in innovation design is overreliance on retrospective use analysis, i.e. that which is based on clear references to existing products or activities. In contrast, innovation design projects are full of uncertainty, leading to a need for prospective analysis. After having described some limitations of prospective use analysis, we contend that creativity tools may be used to assist the anticipation of future product use, by allowing designers to approach the variability of situations of future use in a structured manner rather than by "muddling through". We illustrate the expected benefits of this approach with two case studies, and describe some prospects for future research and practice in ergonomics. Copyright © 2013. Published by Elsevier Ltd.
Toerstad, Elisabeth Heggelund
The application of modern corrosion-resistant alloys to subsea pipelines and components has led to serious problems of hydrogen embrittlement from the corrosion protection system, resulting in cracks and leaks. The most commonly known incidents of this kind are the duplex hubs on Voinhaven, UK and Garn West and the 13% Cr pipelines on Tune and Aasgard, all at the Norwegian shelf. Understanding the nature of this problem has called for a broad multidisciplinary approach, involving expertise on corrosion and metallurgy as well as structural design and integrity. Competence in probabilistic analyses and risk assessments has also been necessary in order to set acceptance criteria and evaluate probability of failure for existing installations. (Det Norske Veritas (DNV) is now about to issues a Recommended Practise (RP) for design of subsea equipment in duplex steels under Cathodic Protection. The RP is based on knowledge gained through failure investigations, qualification pr grams and research work, and a broad industry consortium has contributed with experience and knowledge. Hydrogen Induced Stress Cracking (HISC) due to hydrogen from the Cathodic Protection (CP) system has been one of the most frequent and costly failure modes for subsea equipment and pipelines in the North Sea over the recent years. Today, the international oil business is looking to Norway for assistance in establishing detailed knowledge about and preventive measures against this failure mode. A significant research work is currently being carried out jointly by DNV, SINTEF and TWI (The Welding Institute), supported by a broad industry consortium - aiming at a better understanding of the HISC (Hydrogen Induced Stress Cracking) mechanism and establishment of test methods which reflect the sensitivity to cracking. DNV has also established a Recommended Practice, which will be issued late 2005. It reflects the experience gained from the failure examinations, fitness for purpose evaluations, research
Bandaru, Sunith; Deb, Kalyanmoy
In this article, a methodology is proposed for automatically extracting innovative design principles which make a system or process (subject to conflicting objectives) optimal using its Pareto-optimal dataset. Such 'higher knowledge' would not only help designers to execute the system better, but also enable them to predict how changes in one variable would affect other variables if the system has to retain its optimal behaviour. This in turn would help solve other similar systems with different parameter settings easily without the need to perform a fresh optimization task. The proposed methodology uses a clustering-based optimization technique and is capable of discovering hidden functional relationships between the variables, objective and constraint functions and any other function that the designer wishes to include as a 'basis function'. A number of engineering design problems are considered for which the mathematical structure of these explicit relationships exists and has been revealed by a previous study. A comparison with the multivariate adaptive regression splines (MARS) approach reveals the practicality of the proposed approach due to its ability to find meaningful design principles. The success of this procedure for automated innovization is highly encouraging and indicates its suitability for further development in tackling more complex design scenarios.
Dowling, A.; Gallagher, A.; Walsh, C.; Malone, J.
Interventional radiology has seen rapid growth in cardiology and represents an alternative to hazardous surgery. Recently there has been a substantial growth in the number of procedures being performed and interventional cardiology (IC) procedures are the most common interventional procedures in Europe. Advances in imaging technology have facilitated the development of increasingly complex radiological IC equipment. Currently, the technology is developing at a rate ahead of supporting research, equipment standards and a regulatory framework. International standards play a key role in the design, manufacture and performance of radiological IC equipment. A survey of 12 IC systems (15 imaging chains) was conducted in Irish hospitals. The aim of the study was to assess the imbalance between rapidly advancing technology and existing standards and to propose recommendations for new IC equipment standards. The results demonstrate the need for definitive equipment requirements and standardisation in the design, manufacture, acceptance and maintenance of IC equipment. (authors)
objective is to contribute by discussing the elements that a new framework for eco-design and innovation feasibility studies could provide to the evaluation of technologies that will facilitate a response to the climate, energy and economic development challenges the illumination sector in Denmark faces......This thesis presents an eco-design and innovation feasibility study that focuses on the Danish lighting sector. The main general research objective is: To identify possibilities for further innovations that can contribute to reducing CO2 emissions and reduce the use of fossil fuels. An integrated...... today. To achieve these goals, this study integrates three different levels of systemic analysis: Firstly, the product system analysis, where technological possibilities to improve energy efficiency are discussed and new technological improvements identified. Secondly, it takes into consideration...
This deliverable is the Final Report for Task 1, Cost Estimates of Small Modular Systems, as part of NREL Award ACO-5-44027, ''Equipment Design and Cost Estimation for Small Modular Biomass Systems, Synthesis Gas Cleanup and Oxygen Separation Equipment''. Subtask 1.1 looked into processes and technologies that have been commercially built at both large and small scales, with three technologies, Fluidized Catalytic Cracking (FCC) of refinery gas oil, Steam Methane Reforming (SMR) of Natural Gas, and Natural Gas Liquids (NGL) Expanders, chosen for further investigation. These technologies were chosen due to their applicability relative to other technologies being considered by NREL for future commercial applications, such as indirect gasification and fluidized bed tar cracking. Research in this subject is driven by an interest in the impact that scaling has on the cost and major process unit designs for commercial technologies. Conclusions from the evaluations performed could be applied to other technologies being considered for modular or skid-mounted applications.
''Reactor Site Criteria,'' requires, in part, that safety-related structures, systems, and components remain functional in the event of a Safe Shutdown Earthquake (SSE). It specifies the use of a suitable dynamic analysis as one method of ensuring that the structures, systems, and components can withstand the seismic loads. Similarly, paragraph (a)(2) of Section VI of the same appendix requires, in part, that the structures, systems, and components necessary for continued operation without undue risk to the health and safety of the public remain functional in the event of an Operating Basis Earthquake (OBE). Again, the use of suitable dynamic analysis is specified as one method of ensuring that the structures, systems, and components can withstand the seismic loads. This guide describes methods acceptable to the NRC staff for developing two horizontal and one vertical floor design response spectra at various floors or other equipment-support locations of interest from the time-history motions resulting from the dynamic analysis of the supporting structure. These floor design response spectra are needed for the dynamic analysis of the systems or equipment supported at various locations of the supporting structure
Richir, P.; Dechamp, L.; Buchet, P.; Dransart, P.; Dzbikowicz, Z.; Peerani, P.; ); Pierssens, L.; Persson, L.; Ancius, D.; Synetos, S.; ); Edmonds, N.; Homer, A.; Benn, K.-A.; Polkey, A.
The Nuclear Security unit (NUSEC) of the Institute for Transuranium Elements (ITU, JRC) was entrusted by DG ENER to design and implement equipment in order to achieve enhanced safeguards of a plutonium dioxide storage located on the MAGNOX reprocessing plant in Sellafield (UK). Enhanced safeguards must lead to a win-win situation for all parties involved. In this case the DG ENER inspectorate will save inspection time, manpower and future financial resources and the operator will have the right to access its storage without the need for inspector presence. To reach this goal, while at the same time taking into account current budget constraints, NUSEC developed applications that use equipment commonly used in the safety and security fields but so far have not been used in safeguards. For instance, two laser scanners are used to detect entry/exit events into and out of the store and to provide the necessary information to an algorithm in order to categorize objects/people passing the scanners, e.g., a Fork Lift Truck, a trolley used to bring in PuO 2 containers, a system used for the dispatch of cans, people, etc. An RFID reader is used to identify equipment duly authorized to access the store. All PuO 2 containers arriving from the production line must be weighed, identified and measured using gamma and neutron detectors before they can be transferred to the store. For this purpose an Unattended Combined Measurement System (UCMS) was designed and manufactured by the JRC in order to do all verification activities using a single instrument. This paper describes the design features of the equipment and its implementation with the support of the Sellafield Ltd. in the framework of the MAGNOX store project. (author)
Simon, Matthew A.; Toups, Larry
Increased public awareness of carbon footprints, crowding in urban areas, and rising housing costs have spawned a 'small house movement' in the housing industry. Members of this movement desire small, yet highly functional residences which are both affordable and sensitive to consumer comfort standards. In order to create comfortable, minimum-volume interiors, recent advances have been made in furniture design and approaches to interior layout that improve both space utilization and encourage multi-functional design for small homes, apartments, naval, and recreational vehicles. Design efforts in this evolving niche of terrestrial architecture can provide useful insights leading to innovation and efficiency in the design of space habitats for future human space exploration missions. This paper highlights many of the cross-cutting architectural solutions used in small space design which are applicable to the spacecraft interior design problem. Specific solutions discussed include reconfigurable, multi-purpose spaces; collapsible or transformable furniture; multi-purpose accommodations; efficient, space saving appliances; stowable and mobile workstations; and the miniaturization of electronics and computing hardware. For each of these design features, descriptions of how they save interior volume or mitigate other small space issues such as confinement stress or crowding are discussed. Finally, recommendations are provided to provide guidance for future designs and identify potential collaborations with the small spaces design community.
Paraszczak, J.; Kotersi, O [Laval Univ., Quebec City, PQ (Canada). Dept. of Mining, Metallurgical and Materials Engineering
The challenges associated with mining at considerable depths were discussed. Mines such as Kidd Creek, LaRonde and Creighton are deeper than 2500 m. High rock temperature is among the challenges that operators face in such conditions. Conventional diesel powered load-hauling equipment constitute an additional source of heat and noxious gases. As such, more intense ventilation is needed in order to keep ambient temperature and air quality at a level that is acceptable for human workers. This paper examined possible alternatives for diesel powered equipment, including those that are commercially available as well as those that are underdevelopment or in the prototype stage. The equipment was reviewed with reference to the required infrastructure, stage of technology development and progress. The flexibility, practicality and economic viability of the equipment was also investigated. The potential for its use in deep Canadian mines was discussed along with the most promising drive alternatives for vehicles designed for deep mine operations. Electric drives have proven to be effective in many mining applications since they have significant advantages over diesel drives. The characteristics of cable powered equipment, trolley-wire powered equipment, and battery powered equipment were described. The key advantages and disadvantages of hybrid diesel electric equipment were also reviewed along with the viability of power plants based on the use of hydrogen. The principle types of hydrogen power plants include hydrogen combustion engines; HY-Drive systems and fuel cells. It was concluded that although there is no viable alternative for diesel engines at present, Canadian mining companies operating at great depths have made significant progress in these fields and remain among the leaders in mining innovation. 17 refs.
Johanson, N.W.; Meyer, R.J.; Romesberg, L.E.; Pope, R.B.
A program was initiated in the late 1970's at Sandia National Laboratories to develop an efficient, safe, reliable, and cost-effective transportation packaging system for the carriage of contact-handled transuranic (CH-TRU) waste within the Department of Energy (DOE) complex. It is anticipated that eventually a family of TRUPACT (TRansUranic PACKage Transporter) systems having varied dimensions and weight/volume capacities will be needed by the DOE to transport different CH-TRU waste forms. Each TRUPACT system will be a Type B packaging. Large quantities of CH-TRU wastes having many different forms, isotopic contents, and contained in a variety of waste containers have been, are being, and will continue to be produced and stored for ultimate disposal. Packaging design is being closely coordinated with facility designs to ensure the rapid and economic integration of the TRUPACT system. The first packaging developed for transport by truck or rail (bimodal) is designated TRUPACT-I and will become operational in 1984. This paper provides an overview of progress on the TRUPACT-I design and details of equipment to be used for interfacing with users
... 10 Energy 1 2010-01-01 2010-01-01 false Design objectives for equipment to control releases of... out in appendix I to this part provide numerical guidance on design objectives for light-water-cooled... unrestricted areas be kept as low as is reasonably achievable. These numerical guides for design objectives and...
The development of innovations is increasingly portrayed as a dynamic interplay between two or more actors. This started with the seminal work of von Hippel concerning the role of users during the initial stages of the development cycle. Subsequent studies by numerous academics demonstrated the
The paper deals with strategies of innovation in Polish manufacturing companies. The point of departure is a theoretical framework of enterprise level innovation, and of the factors forming strategies of innovation on enterprise level. The paper analyses evidence from 23 Polish companies and pres......The paper deals with strategies of innovation in Polish manufacturing companies. The point of departure is a theoretical framework of enterprise level innovation, and of the factors forming strategies of innovation on enterprise level. The paper analyses evidence from 23 Polish companies...... and presents two cases more in detail. The analysis shows that the Polish companies have all been quite innovative, mostly in relation to product innovation. They choose innovation strategies, which are incremental more than radical, and they tend to differentiate their product range rather than to specialise....... They consider quality development a must in the fight for market shares and they adapt equipment and organisation to this goal. The factors forming and determining the strategies of the companies count the technological knowledge and expertise of the owner/founder, the structural changes of the market...
Full Text Available Esse artigo trata da inserção do design no processo de desenvolvimento de produtos em duas empresas da indústria calçadista da região do Vale do Paranhana, no Rio Grande do Sul. Essas empresas podem trabalhar com diferentes tipos de equipes, interna, externa ou mista e, entender as vantagens e desvantagens de cada tipo de equipe é fundamental ao determinar a melhor opção para a empresa. Porém, pouco tem-se estudado buscando essa relação entre equipes de design e desenvolvimento de produtos. Nesse sentido, o objetivo do estudo foi analisar o gerenciamento de equipes de design, interna e externa, no processo de desenvolvimento de produtos de empresas da indústria calçadista. Para isso, um estudo de caso foi realizado através da análise do caso de uma empresa que trabalhava com os dois tipos de equipes. Com a realização desta pesquisa, foi possível estudar a forma de atuação e gerenciamento das equipes interna e externa de design no processo de desenvolvimento de produtos. Os resultados indicam que diferenças nas formas de atuação e gerenciamento de cada equipe estão relacionados com a autonomia decisória conferida para equipe no início do desenvolvimento de novos projetos.
Hedtke, James C.
To help keep personnel exposure as low as reasonably achievable and reduce critical path outage time, most nuclear plants of PWR design in the USA are now using improved equipment to service their steam generators (SGs) during outages. Because of the success of this equipment in the USA, two Belgian plants and one English plant have purchased this equipment, and other nuclear plants in Europe are also considering procurement. The improved SG servicing equipment discussed in this paper discusses consists of nozzle dams, segmented multi-stud tensioner, primary manway cover handling tool set, shield door and fastener cleaner. This equipment is specifically designed for the individual plant application and can also be specified for replacement SG projects. All of the equipment can be used without modification of the existing SGs. (author)
Ma, Y.; Lin, Y.; Yang, Y.; Gu, Ch; Yang, F.; Zou, L. D.
With the construction of Material Quality Inspection Center of Shandong electric power company, Electric Power Research Institute takes on more jobs on quality analysis and laboratory calibration for high-voltage electrical equipment, and informationization construction becomes urgent. In the paper we design a consolidated system, which implements the electronic management and online automation process for material sampling, test apparatus detection and field test. In the three jobs we use QR code scanning, online Word editing and electronic signature. These techniques simplify the complex process of warehouse management and testing report transferring, and largely reduce the manual procedure. The construction of the standardized detection information platform realizes the integrated management of high-voltage electrical equipment from their networking, running to periodic detection. According to system operation evaluation, the speed of transferring report is doubled, and querying data is also easier and faster.
Haase, Louise Møller; Laursen, Linda Nhu
Designing a remarkable product innovation is a difficult challenge, which businesses today continuously are striving to tackle. This challenge is particularly present in the early phase of innovation, where the main product concept and frames of the innovation is determined. As a main challenge...... in the early phase is the reasoning process; innovation team are faced with open-ended ill-defines problems, where they need to make decisions about an unknown future having only incomplete, ambiguous and contradicting insights available. We study the reasoning of experts, how they frame to make sense of all...... the insights and create a basis for decision making in relation to a new project. Based on case studies of five innovative products from various industries, we suggest a Product Reasoning Model for understanding reasoning and envisioning of new product innovations in the early phases...
Shkitsa, L. Y.; Panchuk, V. G.; Kornuta, V. A.
There have been analyzed reasons of the loss of technical education’s popularity. Also, the analysis of known educational and production methods, oriented at the innovative model of development of society, was performed. It is stated that the acquisition of 21st century’s skills as a result of competition of technical education are natural for the DIY ideology, which was realized in the institutions like Fab Lab. The new educational strategy, based on project-based learning, is proposed to be implemented as a special laboratory with equipment, which would be a center of innovative development for students at the Technical University. Moreover, the list of projects planned for implementation, that includes not only projects, specific to a particular university, but also projects, demanded by society as a whole, is specified. It is worth to implement trendy projects in the laboratory, such as toy-like, ecological projects; projects of the energy dependence decrease or the energy efficiency increase, modern digital or innovative projects etc. The student should gain knowledge, skills and, possibly, equipment that are available for immediate usage on the labor market or for the realization of his own projects or the community’s projects in everyday life after the realization of the particular project at the laboratory
4 explores how transnational corporations perceive and design an internal network organization to facilitate global innovation. Based on a multiple case study of three Danish transnational corporations’ global R&D organization, this paper shows three types of network organization design...... explores how an SME develops a network organization consisting of both interfirm innovation networks and an internal network organization to facilitate its global innovation strategy. Regarding the intraorganizational network organization, market mechanism is adopted to optimize internal resource...... corporations perceive/design a network organization to facilitate their global innovation? • To what extent and how can we manage a network organization? Research focus of the dissertation is on transnational corporations’ network organization for innovation. The first research question aims to clarify...
Jirasatjanukul, Kanokrat; Jeerungsuwan, Namon
The objectives of the research were to (1) design an instructional model based on Connectivism and Constructivism to create innovation in real world experience, (2) assess the model designed--the designed instructional model. The research involved 2 stages: (1) the instructional model design and (2) the instructional model rating. The sample…
The main purpose of this study was to explore the care-givers of preschool education institutions whose cognition on playing equipment functions, conditions of both setting and using, and the main factors which should beware of design. Besides, not only constructed the factors of design, but also provided suggestions about setting and designing of…
Hongbin Zhang; Haihua Zhao; Vincent Mousseau
Investment in commercial sodium cooled fast reactor (SFR) power plants will become possible only if SFRs achieve economic competitiveness as compared to light water reactors and other Generation IV reactors. Toward that end, we have launched efforts to improve the economics and safety of SFRs from the thermal design and safety analyses perspectives at Idaho National Laboratory. From the thermal design perspective, an innovative hybrid loop-pool SFR design has been proposed. This design takes advantage of the inherent safety of a pool design and the compactness of a loop design to further improve economics and safety. From the safety analyses perspective, we have initiated an effort to develop a high fidelity reactor system safety code
Oudenhuijzen, A.J.K.; Reulink, H.G.B.; Kistemaker J.A.
Everybody seems to know how simple it is to procure personal equipment (PE). Still, users of PE are too often confronted with shortcomings in their PE: they may be hampered, or and/or individual components of the PE ensemble do not work together. So the question is: do we really know how to procure
This paper examines the methodological challenges and perspectives of designing game-like scenarios for the implementation of innovation processes in school science education. This paper presents a design-based research study of a game-like innovation scenario designed for technology education for Danish public school students aged 13-15. Students…
Gagić Snježana; Tešanović Dragan; Kalenjuk Bojana
Innovation is an important aspect of contemporary business. Rapid change in guests' preferences and expectations significantly affect the restaurant industry. Meeting the diverse hospitality needs implies making innovative programs in all processes such as technical, technological as well as service oriented. Hospitality industry enters into the process of accelerated changes of modern equipment, updated technology, business strategies and hospitality management. The paper will discuss innova...
The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) retrieval from the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. There are no quality assurance requirements or QA controls in this document. Retrieval under normal conditions is accomplished with the same fleet of equipment as is used for emplacement. Descriptions of equipment used for retrieval under normal conditions is found in Emplacement Equipment Descriptions, DI: BCAF00000-01717-5705-00002 (a document in progress). Equipment used for retrieval under abnormal conditions is addressed in this document and consists of the following: (1) Inclined Plane Hauler; (2) Bottom Lift Transporter; (3) Load Haul Dump (LHD) Loader; (4) Heavy Duty Forklift for Emplacement Drifts; (5) Covered Shuttle Car; (6) Multipurpose Vehicle; and (7) Scaler
Guggisberg, B.; Daehler, P. [ABB Schweiz AG, Turgi (Switzerland)
The BORDLINE-Compact Converter consists of a main traction converter with integrated auxiliary converter. The converters are equipped with low voltage semiconductors and are intended to be used in DMUs as well as in EMUs with overhead voltages of 15 kV or 25 kV. For the operation with 3 kV DC an additional DC to AC converter using a separate main transformer winding is installed. (orig.)
Takahisa, Kenji; Yoo, Young Sun; Fukuda, Hitomi; Minegishi, Yuji; Enami, Tatsuo
Semiconductor manufacturing industry has growing concerns over future environmental impacts as fabs expand and new generations of equipment become more powerful. Especially rare gases supply and price are one of prime concerns for operation of high volume manufacturing (HVM) fabs. Over the past year it has come to our attention that Helium and Neon gas supplies could be unstable and become a threat to HVM fabs. To address these concerns, Gigaphoton has implemented various green technologies under its EcoPhoton program. One of the initiatives is GigaTwin deep ultraviolet (DUV) lithography laser design which enables highly efficient and stable operation. Under this design laser systems run with 50% less electric energy and gas consumption compared to conventional laser designs. In 2014 we have developed two technologies to further reduce electric energy and gas efficiency. The electric energy reduction technology is called eGRYCOS (enhanced Gigaphoton Recycled Chamber Operation System), and it reduces electric energy by 15% without compromising any of laser performances. eGRYCOS system has a sophisticated gas flow design so that we can reduce cross-flow-fan rotation speed. The gas reduction technology is called eTGM (enhanced Total gas Manager) and it improves gas management system optimizing the gas injection and exhaust amount based on laser performances, resulting in 50% gas savings. The next steps in our roadmap technologies are indicated and we call for potential partners to work with us based on OPEN INNOVATION concept to successfully develop faster and better solutions in all possible areas where green innovation may exist.
... proposal, such as sports equipment, arts and crafts supplies, chairs and tables if needed for an activity... innovation should demonstrate a concept that is untried, unique, and/or advances the state of the art for...
A. Kristensen, Anders Schmidt
Cooling of electronic equipment is studied. The design size of electronic equipment decrease causing the thermal density to increase. This affect the cooling which can cause for example failures of critical components due to overheating or thermal induced stresses. Initially a pin fin heat sink...
With the development of the aging society and the increased importance of emergency risk management in recent years, a large number of medical care challenges - advancing medical treatments, care & support, pharmacological treatments, greater health awareness, emergency treatments, telemedical treatment and care, the introduction of electronic charts, and rising costs - are emerging as social issues throughout the whole world. Hospitals and other medical institutions must develop and maintain superior management to achieve systems that can provide better medical care, welfare and health while enabling "support innovation." Key medical care, welfare and health industries play a crucial role in this, but also of importance are management innovation models that enable "collaborative innovation" by closely linking diverse fields such as ICT, energy, electric equipment, machinery and transport. Looking across different industries, Collaborative Innovation offers new knowledge and insights on the extraord...
Barthe, Jean; Hugon, Régis; Nicolai, Jean Philippe
The integrated project MAESTRO (Methods and Advanced Equipment for Simulation and Treatment in Radio-Oncology) under contract with the European Commission in life sciences FP6 (LSHC-CT-2004-503564), concerns innovative research to develop and validate in clinical conditions, advanced methods and equipment needed in cancer treatment for new modalities in high-conformal external radiotherapy using electrons, photons and protons beams of high energy.
Ansart, A; Manuel, P [Electricite de France (EDF); Fevrier, A [Compagnie Generale d' Electricite (CGE), 91 - Marcoussis (FR)
Development of superconductors for AC current and of higher critical temperature superconducting materials enlarged the field of research in cryoelectrotechnic. The paper discusses the materials characteristics in relation with the functional needs in the equipments. Are reviewed the main points governing conductor design for a given application, the characteristics and manufacturing technics for different superconducting materials. It is shown how lighter, smaller equipments can be designed as well as new ones for functions not covered with present apparatus. 17 refs.
Desroches, Louis-Benoit; Garbesi, Karina
It is well established that energy efficiency is most often the lowest cost approach to reducing national energy use and minimizing carbon emissions. National investments in energy efficiency to date have been highly cost-effective. The cumulative impacts (out to 2050) of residential energy efficiency standards are expected to have a benefit-to-cost ratio of 2.71:1. This project examined energy end-uses in the residential, commercial, and in some cases the industrial sectors. The scope is limited to appliances and equipment, and does not include building materials, building envelopes, and system designs. This scope is consistent with the scope of DOE's appliance standards program, although many products considered here are not currently subject to energy efficiency standards. How much energy could the United States save if the most efficient design options currently feasible were adopted universally? What design features could produce those savings? How would the savings from various technologies compare? With an eye toward identifying promising candidates and strategies for potential energy efficiency standards, the Max Tech and Beyond project aims to answer these questions. The analysis attempts to consolidate, in one document, the energy savings potential and design characteristics of best-on-market products, best-engineered products (i.e., hypothetical products produced using best-on-market components and technologies), and emerging technologies in research & development. As defined here, emerging technologies are fundamentally new and are as yet unproven in the market, although laboratory studies and/or emerging niche applications offer persuasive evidence of major energy-savings potential. The term 'max tech' is used to describe both best-engineered and emerging technologies (whichever appears to offer larger savings). Few best-on-market products currently qualify as max tech, since few apply all available best practices and components. The
Kang, H. T.; Lee, J. K.; Lee, K. D.; Jo, S. H.
The major goal of nuclear power industries during the past 10 years is to increase reliability and utility capacity factor. As the capacitor factor, however, crept upward. it became harder to attain next percentage of improvement. Therefore other innovative technologies are required. By the technologies applied to the fossil power plants, equipment health monitoring was performed on equipment to maintain it in operable condition and contributed on improving their reliability a lot. But the equipment monitoring may be limited to the observation of current system states in nuclear power plant. Monitoring of current system states is being augmented with prediction of future operating states and predictive diagnosis of future failure states. Such predictive diagnosis is motivated by the need for nuclear power plants to optimize equipment performance and reduce costs and unscheduled downtime. This paper reviews the application of techniques that focus on improving reliability in nuclear power plant by monitoring and predicting equipment health and suggests how possible to support on-line monitoring
The purpose of this study is to identify candidate Monitored Geologic Repository (MGR) surface waste handling equipment for development testing. This study will also identify strategies for performing the development tests. Development testing shall be implemented to support detail design and reduce design risks. Development testing shall be conducted to confirm design concepts, evaluate alternative design concepts, show the availability of needed technology, and provide design documentation. The candidate equipment will be selected from MGR surface waste handling equipment that is the responsibility of the Management and Operating Contractor (M and O) Surface Design Department. The equipment identified in this study is based on Viability Assessment (VA) design. The ''Monitored Geologic Repository Test and Evaluation Plan'' (MGR T and EP), Reference 5.1, was used as a basis for this study. The MGR T and EP reflects the extent of test planning and analysis that can be conducted, given the current status of the MGR requirements and latest VA design information. The MGR T and EP supports the appropriate sections in the license application (LA) in accordance with 10 CFR 60.2 1(c)(14). The MGR T and EP describes the following test activities: site characterization to confirm, by test and analysis, the suitability of the Yucca Mountain site for housing a geologic repository; development testing to investigate and document design concepts to reduce risk; qualification testing to verify equipment compliance with design requirements, specifications, and regulatory requirements; system testing to validate compliance with MGR requirements, which include the receipt, handling, retrieval, and disposal of waste; periodic performance testing to verify preclosure requirements and to demonstrate safe and reliable MGR operation; and performance confirmation modeling, testing, and analysis to verify adherence to postclosure regulatory requirements. Development test activities can be
Ha, Huiun; Lee, Sang Won; Kim, Hangon
Using the Generation of Thermal-Hydraulic Information for Containments (GOTHIC) code, thermal-hydraulic phenomena that occur inside the containment have been investigated, along with the preliminary design of the passive containment cooling system (PCCS) of an innovative pressurized water reactor (PWR). A GOTHIC containment model was constructed with reference to the design data of the Advanced Power Reactor 1400, and report related PCCS. The effects of the design parameters were evaluated for passive containment cooling tank (PCCT) geometry, PCCS heat exchanger (PCCX) location, and surface area. The analyzed results, obtained using the single PCCT, showed that repressurization and reheating phenomena had occurred. To resolve these problems, a coupled PCCT concept was suggested and was found to continually decrease the containment pressure and temperature without repressurization and reheating. If the installation level of the PCCX is higher than that of the PCCT, it may affect the PCCS performance. Additionally, it was confirmed that various means of increasing the external surface area of the PCCX, such as fins, could help improve the energy removal performance of the PCCS. To improve the PCCS design and investigate its performance, further studies are needed
Full Text Available Using the Generation of Thermal-Hydraulic Information for Containments (GOTHIC code, thermal-hydraulic phenomena that occur inside the containment have been investigated, along with the preliminary design of the passive containment cooling system (PCCS of an innovative pressurized water reactor (PWR. A GOTHIC containment model was constructed with reference to the design data of the Advanced Power Reactor 1400, and report related PCCS. The effects of the design parameters were evaluated for passive containment cooling tank (PCCT geometry, PCCS heat exchanger (PCCX location, and surface area. The analyzed results, obtained using the single PCCT, showed that repressurization and reheating phenomena had occurred. To resolve these problems, a coupled PCCT concept was suggested and was found to continually decrease the containment pressure and temperature without repressurization and reheating. If the installation level of the PCCX is higher than that of the PCCT, it may affect the PCCS performance. Additionally, it was confirmed that various means of increasing the external surface area of the PCCX, such as fins, could help improve the energy removal performance of the PCCS. To improve the PCCS design and investigate its performance, further studies are needed.
Ha, Huiun; Lee, Sang Won; Kim, Hangon [Central Research Institute, Korea Hydro and Nuclear Power, Ltd., Daejeon (Korea, Republic of)
Using the Generation of Thermal-Hydraulic Information for Containments (GOTHIC) code, thermal-hydraulic phenomena that occur inside the containment have been investigated, along with the preliminary design of the passive containment cooling system (PCCS) of an innovative pressurized water reactor (PWR). A GOTHIC containment model was constructed with reference to the design data of the Advanced Power Reactor 1400, and report related PCCS. The effects of the design parameters were evaluated for passive containment cooling tank (PCCT) geometry, PCCS heat exchanger (PCCX) location, and surface area. The analyzed results, obtained using the single PCCT, showed that repressurization and reheating phenomena had occurred. To resolve these problems, a coupled PCCT concept was suggested and was found to continually decrease the containment pressure and temperature without repressurization and reheating. If the installation level of the PCCX is higher than that of the PCCT, it may affect the PCCS performance. Additionally, it was confirmed that various means of increasing the external surface area of the PCCX, such as fins, could help improve the energy removal performance of the PCCS. To improve the PCCS design and investigate its performance, further studies are needed.
Sager, P.; Garin, J.; Hager, E.R.; Spampinato, P.T.; Tobias, D.; Young, N.
A workshop was convened in two sessions in January and March 1981, on the remote maintenance equipment for the Fusion Engineering Device (FED). The objectives of the first session were to familiarize the participants with the status of the design of the FED and to develop a remote maintenance equipment list for the FED. The objective of the second session was to have the participants present design concepts for the equipment which had been identified in the first session. The equipment list was developed for general purpose and special purpose equipment. The general purpose equipment was categorized as manipulators and other, while the special purpose equipment was subdivided according to the reactor subsystem it serviced: electrical, magnetic, and nuclear. Both mobile and fixed base manipulators were identified. Handling machines were identified as the major requirement for special purpose equipment
Vechakul, Jessica; Shrimali, Bina Patel; Sandhu, Jaspal S
This case study provides a high-level overview of the human-centered design (HCD) or "design thinking" process and its relevance to public health. The Best Babies Zone (BBZ) initiative is a multi-year project aimed at reducing inequities in infant mortality rates. In 2012, BBZ launched pilot programs in three US cities: Cincinnati, Ohio; New Orleans, Louisiana; and Oakland, California. The Alameda County Public Health Department (ACPHD), the lead for the Oakland BBZ site, identified HCD as a promising approach for addressing the social and economic conditions that are important drivers of health inequities. HCD is a process for creating innovative products, services, and strategies that prioritizes the needs of the intended population. ACPHD partnered with the Gobee Group (a social innovation design consultancy) to develop the Design Sprint. The Design Sprint was a 12-week pilot in which 14 professionals from nine organizations used the HCD process to develop concepts for stimulating a vibrant local economy in the Oakland Best Babies Zone. Thirty- to sixty-minute semi-structured interviews were conducted with all 14 individuals involved in the Design Sprint. With the exception of one interview, the interviews were audio-recorded, transcribed, and inductively coded to identify themes. Our experience suggests that HCD can: enhance community engagement; expedite the timeframe for challenge identification, program design, and implementation; and create innovative programs that address complex challenges.
Borch, Ole; Nielsen, P.S.
. This article presents how simple equipment was used and how the pedagogical model is implemented in the innovation process. The way slides, sound, video and whiteboard were used in a virtual college as well as performing the exam is described. The methods were used in the course: "Object Oriented Programming...
Full Text Available At present, in domestic for the management of well control equipment continue to the traditional way of nameplates identifies and paper-based registration, there are many issues like the separation of data information of device, easy lose, difficult query, confused management and many other problems, which will make the problem device into the well field, and then resulting in well control runaway drilling accident. To solve the above problems, this paper put forward to the integrated remote centralized-monitoring management mode of the well-control equipment. Taking the advantages of IOT technology, adopting the RFID technology, and combining with the remote transmission, this paper designs the remote centralized-monitoring system of well-control equipment based on RFID, which realizes the intelligent management of well-control equipment and meets the actual demand of the well-control equipment safe use and timely scheduling, and it has the ability of field application.
Spampinato, P.T.; Masson, L.S.; Watts, K.D.; Grant, N.R.; Kuban, D.P.
Maintenance equipment which is needed to remotely handle fusion device components is being conceptually developed for the Fusion Engineering Design Center. This will test the assumption that these equipment needs can be satisfied by present technology. In addition, the development of equipment conceptual designs will allow for cost estimates which have a much higher degree of certainty. Accurate equipment costs will be useful for assessments which trade off gains in availability as a function of increased investments in maintenance equipment
Kalivas, Dimitris; Panou-Diamandi, Ourania; Zeelenberg, Cees; van Nimwegen, Chris
Background The MEDICOM (Medical Products Electronic Commerce) Portal provides the electronic means for medical-equipment manufacturers to communicate online with their customers while supporting the Purchasing Process and Post Market Surveillance. The Portal offers a powerful Internet-based search tool for finding medical products and manufacturers. Its main advantage is the fast, reliable and up-to-date retrieval of information while eliminating all unrelated content that a general-purpose search engine would retrieve. The Universal Medical Device Nomenclature System (UMDNS) registers all products. The Portal accepts end-user requests and generates a list of results containing text descriptions of devices, UMDNS attribute values, and links to manufacturer Web pages and online catalogues for access to more-detailed information. Device short descriptions are provided by the corresponding manufacturer. The Portal offers technical support for integration of the manufacturers' Web sites with itself. The network of the Portal and the connected manufacturers' sites is called the MEDICOM system. Objective To establish an environment hosting all the interactions of consumers (health care organizations and professionals) and providers (manufacturers, distributors, and resellers of medical devices). Methods The Portal provides the end-user interface, implements system management, and supports database compatibility. The Portal hosts information about the whole MEDICOM system (Common Database) and summarized descriptions of medical devices (Short Description Database); the manufacturers' servers present extended descriptions. The Portal provides end-user profiling and registration, an efficient product-searching mechanism, bulletin boards, links to on-line libraries and standards, on-line information for the MEDICOM system, and special messages or advertisements from manufacturers. Platform independence and interoperability characterize the system design. Relational Database
Palamas, S; Kalivas, D; Panou-Diamandi, O; Zeelenberg, C; van Nimwegen, C
The MEDICOM (Medical Products Electronic Commerce) Portal provides the electronic means for medical-equipment manufacturers to communicate online with their customers while supporting the Purchasing Process and Post Market Surveillance. The Portal offers a powerful Internet-based search tool for finding medical products and manufacturers. Its main advantage is the fast, reliable and up-to-date retrieval of information while eliminating all unrelated content that a general-purpose search engine would retrieve. The Universal Medical Device Nomenclature System (UMDNS) registers all products. The Portal accepts end-user requests and generates a list of results containing text descriptions of devices, UMDNS attribute values, and links to manufacturer Web pages and online catalogues for access to more-detailed information. Device short descriptions are provided by the corresponding manufacturer. The Portal offers technical support for integration of the manufacturers Web sites with itself. The network of the Portal and the connected manufacturers sites is called the MEDICOM system. To establish an environment hosting all the interactions of consumers (health care organizations and professionals) and providers (manufacturers, distributors, and resellers of medical devices). The Portal provides the end-user interface, implements system management, and supports database compatibility. The Portal hosts information about the whole MEDICOM system (Common Database) and summarized descriptions of medical devices (Short Description Database); the manufacturers servers present extended descriptions. The Portal provides end-user profiling and registration, an efficient product-searching mechanism, bulletin boards, links to on-line libraries and standards, on-line information for the MEDICOM system, and special messages or advertisements from manufacturers. Platform independence and interoperability characterize the system design. Relational Database Management Systems are used for
Maaike Kleinsmann; Janneke Sluijs; Rianne Valkenburg
"The World of the [open] innovator" described the background of the revolution we are in in innovation and what the consequences are for innovation, changing towards design driven open innovation. We reframed innovation to meet new needs and values of companies and organizations in our work field.
Objectives: The study objectives were, firstly, to establish the determinants for complexity and how these can be addressed from a design point of view in order to ensure innovation success and, secondly, to determine how this changes innovation forms and applications. Method: Two approaches were offered to deal with a complex environment – one allowing for complexity for organisational innovation and the other introducing reductionism to minimise complexity. These approaches were examined in a qualitative study involving case studies, open-ended interviews and content analysis between seven developing economy (South African organisations and seven developed economy (US organisations. Results: This study presented a proposed framework for (organisational innovation in a complex environment versus a framework that minimises complexity. The comparative organisational analysis demonstrated the importance of initiating organisational innovation to address internal and external complexity, with the focus being on the leadership actions, their selected operating models and resultant organisational innovations designs, rather than on technological innovations. Conclusion: This study cautioned the preference for technological innovation within organisations and suggested alternative innovation forms (such as organisational and management innovation be used to remain competitive in a complex environment.
The International Reactor Innovative and Secure (IRIS) is an advanced, integral, light water cooled reactor of medium generating capacity (335 MW(e)), that features an integral reactor vessel containing all the reactor primary system components, including steam generators, coolant pumps, pressurizer and heaters, and control rod drive mechanisms; in addition to the typical core, internals, control rods and neutron reflector. This integral configuration allows for the use of a small, high design pressure, spherical steel containment which results in a significant reduction in the size of the nuclear island. Other IRIS innovations include a simplified passive safety system concept and equipment features that derive from the 'safety-by-design' philosophy. This design approach allows for elimination of certain accident initiators at the design stage, or when outright elimination is not possible, decreases accident consequences and/or their probability of occurrence. Major design characteristics of the IRIS are given. As part of the IRIS pre-application licensing review by the U.S. Nuclear Regulatory Commission (NRC), the IRIS design team has developed a test plan that will provide the necessary data for safety analysis computer model verification, as well as for verifying the manufacturing feasibility, operability, and durability of new component designs
3 Features of interactions between public research organizations and industry in Latin ..... The questionnaire for innovative firms was based on the original ..... Technological revolutions at the centre determine another structural feature of the ..... embodied in technology – through the acquisition of machinery, equipment, and ...
Broberg, Ole; Edwards, Kasper
This paper presents experiences from a user-driven innovation process of an outpatient department in a hospital. The mixing of methods from user-driven innovation and participatory design contributed to develop an innovative concept of the spatial and organizational design of an outpatient...
Rahmat; Budi Santoso; Krismawan; Abdul Jalil
Mechanical design for positioning of GM detector system has been done. It is used for avian flu detection equipment. The requirements for the design are to protect detection system against shock, portable, and easy to maintain. The mechanical system consists of connectors, cable assemblies, holders, casing, housing and detectors cover. The selected material should have small gamma radiation absorption property in order to give optimum counts for the detector. The design result should give a system that is easy to operate, cheap and easy to assemble. (author)
Arentsen, Maarten J.; Dinica, V.; Marquart, N.E.
Advanced environmental standards such as sustainability require substantial improvements in the environmental performances of present technologies. Governments are faced with the challenge to design green innovation policies able to support producers and users of technologies to comply with such
Amann, H.; Hohnberg, H.J.; Reinelt, R. [Technische Univ. Berlin (Germany). Inst. fuer Schiffs- und Meerestechnik, Fachgebiet Maritime Technik
HYACE, the acronym for hydrate autoclave coring equipment system, is a research and development project sponsored by the European Union`s Marine Science and Technology Programme MAST. The project was to have started in the fourth quarter of 1997 and is to last 30 months. The main activities of the project will be in the development and prototype testing of an innovative down-hole controlled autoclave coring system. This system will be designed to sample marine sediments at extended down-hole conditions maintaining as many parameters constant as possible. In general terms, the main aim of the project is to contribute to systematic ground truthing of a necessarily ephemeral phenomenon of growing global significance: sampling and analysis of gas hydrates in their natural environment. (MSK)
Operation environment in handling hot slag, radio active material, clearing/dismantling buildings and loose rocky zones pose hazards with the operation of heavy duty vehicles. Under such hazardous environment conditions, elimination of operator becomes the prime criteria. Remote control of heavy vehicles is resorted to operate the equipment in various working conditions. Radio control systems coupled with penumatic/hydraulic actuators and proportional control logics aim total control of the equipment from a distance using hand pendants. Bharat Earth Moovers Limited has successfully developed remote control system for dozers of 200hp and 300hp. (author). 3 figs
Chen, G.; Schott, D.L.; Lodewijks, G.
Large-scale handling of particulate solids can cause severe wear on bulk solids handling equipment surfaces. Wear reduces equipment life span and increases maintenance cost. Examples of traditional methods to reduce wear of bulk solids handling equipment include optimizing transport operations
Buur, Jacob; Matthews, Ben
In this paper we discuss the potential for Participatory Design (PD) to make a fundamental contribution to the business-oriented field of user-driven innovation, taking note of where we find PD can best benefit from interaction with this other field. We examine some of the challenges that must...... be addressed if PD is to contribute to innovation processes in companies. We conclude by presenting a research agenda comprising of six promising topics to shape a new discipline of Participatory Innovation....
scenario designed for technology education in grades 7 - 9 in Danish schools. In the paper, methodological challenges of doing design-based research into technology innovation education are discussed. The preliminary results from the first studies of a game-inspired technology innovation camp are also...
Jensen, Jesper Legaard
This paper explores innovation in relation to product design, with an emphasis on designing for experiences. In the paper I introduce an experiential model called the “Peel model”, and showcase how it can be applied as a tool for innovation. The Peel model depicts different layers of a product......, and transferred that concept to other product types, generating ideas about how a lamp, for instance, could provide a similar experience. The introduced Peel model is intended to be beneficial at an operational level for designers, project managers, business executives etc. as a tool to guide the innovation...
to clustering of ideas, a design strategy which seemed to kill unique ideas. The reframing of innovation as a radical endeavor killed learning from others for being not innovative. The findings of this paper supplement theories of deliberate killing of ideas by suggesting framing, design and facilitation......This paper points to seemingly contradicted processes of framing innovation, idea generation and killing ideas. It reports from a yearlong innovation project, where health care professionals explored problems and tested ideas for solutions, regarding a future downsizing of the case hospital....... Theories in various ways describe the opening and closing phases of innovation. Exploration and idea generation opens a field of interest, which is then closed by making choices of ideas to further explore in the next opening phase. These choices deliberately kill a lot of ideas. In the innovation project...
Dawes, Andrew; Biersteker, Linda; Girdwood, Elizabeth; Snelling, Matthew; Tredoux, C. G.
In 2015, Innovation Edge commissioned the development of South Africa's first national-level preschool child assessment tool. The project's key innovations were that the tool should fairly assess children from across the cultural and socio-economic spectrum, be inexpensive in terms of equipment and administration costs, and be administered in…
Full Text Available The thermal treatment of waste by incineration is considered an ultimate solution in order to get rid of waste properly by using the combustible properties of waste and transforming them into inert form and gaseous emission, with the main advantage of a huge reduction in mass and volume of treated waste, destruction of the dangerous components in waste, and obtaining green and clean energy from the exothermal reaction from the completed combustion process. In order to achieve the main goal of incineration, a good design, construction, supervision, and intensive operation and maintenance must be taken into account, especially for the small-scale incinerator. This research will deal with the green, innovative, and eco design and manufacturing technology of a 1-ton per batch municipal solid waste (MSW incinerator. The concept design of the incinerator will focus on the design of the feeding process where only one batch of waste will be discharged into the combustion chamber at one time instead of the semi-feed process, as found in the conventional incinerator. This will ease the operation of the operator and reduce the operating cost. Moreover, the innovative design includes the redesign of combustion air injection into either the primary or secondary combustion chamber in order to achieve the 3Ts of combustion (time, temperature. and turbulence. This design can eliminate the use of an auxiliary burner in the primary combustion chamber. Rethinking the innovative design of using recirculation hot flue gas for preheating of wet garbage in order to pre-dry the waste before combustion is also taken into account. The manufacturing process of the wall composition as well as other parts of the incinerator are also examined.
Busatta, A.; Marchiori, G.; Mian, S.; Payne, I.; Pozzobon, M.
The close-pack array of the MROI necessitated an original design for the Unit Telescope Enclosure (UTE) at Magdalena Ridge Observatory. The Magdalena Ridge Observatory Interferometer (MROI) is a project which comprises an array of up to ten (10) 1.4m diameter mirror telescopes arranged in a "Y" configuration. Each of these telescopes will be housed inside a Unit Telescope Enclosure (UTE) which are relocatable onto any of 28 stations. The most compact configuration includes all ten telescopes, several of which are at a relative distance of less than 8m center to center from each other. Since the minimum angle of the field of regard is 30° with respect to the horizon, it is difficult to prevent optical blockage caused by adjacent UTEs in this compact array. This paper presents the design constraints inherent in meeting the requirement for the close-pack array. An innovative design enclosure was created which incorporates an unique dome/observing aperture system. The description of this system focuses on how the field of regard requirement led to an unique and highly innovative concept that had to be able to operate in the harsh environmental conditions encountered at an altitude of 10,460ft (3,188m). Finally, we describe the wide use of composites materials and structures (e.g. glass/carbon fibres, sandwich panels etc.) on the aperture system which represents the only way to guarantee adequate thermal and environmental protection, compactness, structural stability and limited power consumption due to reduced mass.
... EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND EQUIPMENT Special Compliance Provisions § 1054... provisions of this section and send us an annual report, as follows: (1) Notify the Designated Compliance... and manufacturing equipment. Companies that import equipment into the United States without meeting...
Luciana Fighera Marzall
Full Text Available Innovation has been considered of fundamental importance for organizations competing in dynamic environments, which along with cost management has been shown as an organizational strategy that allows the company to measure its results and implement measures that impact on the organization's performance as a whole. This paper, carried out in a metal mechanical industry of a telecommunications engineering branch, aims to analyse cost reduction in logistics raw materials areas through innovation in the product design, which are antennas and towers for telephone networks. In terms of methodology, this study presents itself as a qualitative and quantitative research-action, which from the link between theory and practice allows for intervention in the middle of the researchers studied. As a result, an innovative project was developed, which allowed for the reduction costs of production by 68% and logistics by 32%. Despite the significant decrease in costs, the quality of manufactured products not declined and customer needs were met, thus making the company more competitive against competitors. Not widespread in the literature, this analysis of the impact on logistics and production costs due to improvements in the project is the main contribution theoretical of this paper.
Sastry, V.S.; Raju, Y.S.; Somani, A.K.; Setty, D.S.; Rameswara Raw, A.; Hermantha Rao, G.V.S.; Jayaraj, R.N. [Nuclear Fuel Complex, Dept. of Atomic Energy, Hyderbad (India)
Indian Pressurised Heavy Water Reactor (PHWR) fuel bundle is fully welded and is unique in its design. Appendage welding, end closure welding, and end plate welding is carried out using resistance welding technique. Out of many joining processes available, resistance-welding process is reliable, environment friendly and best suitable for mass production applications. Nuclear Fuel Complex (NFC), an industrial unit is established in Hyderabad, under the aegis of the Dept of Atomic Energy to manufacture fuel for Pressurised Heavy Water Reactors. From inception, NFC has given importance for self-reliance and indigenization with respect to manufacturing process and equipment. Sintering furnaces, centreless grinders, appendage-welding machines, end-closure welding equipment and end-plate welding equipments, which were initially imported, are either indigenized or designed and manufactured in house. NFC has designed, manufactured a new appendage-welding machine for manufacturing 37 element fuel bundles. Recently NFC has bagged an order from IAEA through international bidding for design, manufacture, supply, erection and commissioning of end-closure welding equipment. The paper gives in detail the salient features of these welding equipment. (author)
Tukiran S; Surian Pinem; Tagor MS; Lily S; Jati Susilo
The multipurpose of research reactor utilization make many countries build the new research reactor. Trend of this reactor for this moment is multipurpose reactor type with a compact core to get high neutron flux at the low or medium level of power. The research newest. Reactor in Indonesia right now is already 25 year old. Therefore, it is needed to design a new research reactor, called innovative research reactor (IRR) and then as an alternative to replace the old research reactor. The aim of this research is to get the optimal configuration of equilibrium core with the acceptance criteria are minimum thermal neutron flux is 2.5E14 n/cm 2 s at the power level of 20 MW (minimum), length of cycle of more than 40 days, and the most efficient of using fuel in the core. Neutronics design has been performed for new fuel of U-9Mo-AI with various fuel density and reflector. Design calculation has been performed using WIMSD-5B and BATAN-FUEL computer codes. The calculation result of the conceptual design shows four core configurations namely 5x5, 5x7, 6x5 and 6x6. The optimalization result for equilibrium core of innovative research reactor is the 5x5 configuration with 450 gU fuel loading, berilium reflector, maximum thermal neutron flux at reflector is 3.33E14 n/cm 2 sand length of cycle is 57 days is the most optimal of IRR. (author)
Leonard, Simon N.; Fitzgerald, Robert N.; Riordan, Geoffrey
This paper argues for the use of "developmental" evaluation as a design-based research tool for sustainable curriculum innovation in professional higher education. Professional education is multi-faceted and complex with diverse views from researchers, professional practitioners, employers and the world of politics leaving little…
Full Text Available Expert Systems can be defined as computer programs, whose main task is to simulate a human expert, usually in a narrow field of expertise. Expert Systems have experienced tremendous growth and popularity since their commercial introduction in the early 1970’s. Today, Expert Systems are used in business, science, engineering, manufacturing and other engineering applications such as planning, scheduling, diagnosing equipment failures and are used in almost every stage of the manufacturing process and also in medicine and many other fields. Expert Systems belong to the field of artificial intelligence. An intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for the solution. The purpose of this paper is to present an Expert System which assists with the design of yachts and supports the selection of mechanical equipment for yachts and includes knowledge in the field of yachting engineering. Using the presented Expert System reduces the time during the design and production preparation process.