DECONTAMINATION TECHNOLOGIES FOR FACILITY REUSE

International Nuclear Information System (INIS)

Bossart, Steven J.; Blair, Danielle M.

2003-01-01

As nuclear research and production facilities across the U.S. Department of Energy (DOE) nuclear weapons complex are slated for deactivation and decommissioning (D and D), there is a need to decontaminate some facilities for reuse for another mission or continued use for the same mission. Improved technologies available in the commercial sector and tested by the DOE can help solve the DOE's decontamination problems. Decontamination technologies include mechanical methods, such as shaving, scabbling, and blasting; application of chemicals; biological methods; and electrochemical techniques. Materials to be decontaminated are primarily concrete or metal. Concrete materials include walls, floors, ceilings, bio-shields, and fuel pools. Metallic materials include structural steel, valves, pipes, gloveboxes, reactors, and other equipment. Porous materials such as concrete can be contaminated throughout their structure, although contamination in concrete normally resides in the top quarter-inch below the surface. Metals are normally only contaminated on the surface. Contamination includes a variety of alpha, beta, and gamma-emitting radionuclides and can sometimes include heavy metals and organic contamination regulated by the Resource Conservation and Recovery Act (RCRA). This paper describes several advanced mechanical, chemical, and other methods to decontaminate structures, equipment, and materials

Facility decontamination technology workshop

International Nuclear Information System (INIS)

1980-10-01

Purpose of the meeting was to provide a record of experience at nuclear facilities, other than TMI-2, of events and incidents which have required decontamination and dose reduction activities, and to furnish GPU and others involved in the TMI-2 cleanup with the results of that decontamination and dose reduction technology. Separate abstracts were prepared for 24 of the 25 papers; the remaining paper had been previously abstracted

Facility decontamination technology workshop

Energy Technology Data Exchange (ETDEWEB)

None

1980-10-01

Purpose of the meeting was to provide a record of experience at nuclear facilities, other than TMI-2, of events and incidents which have required decontamination and dose reduction activities, and to furnish GPU and others involved in the TMI-2 cleanup with the results of that decontamination and dose reduction technology. Separate abstracts were prepared for 24 of the 25 papers; the remaining paper had been previously abstracted. (DLC)

Development of decontamination, decommissioning and environmental restoration technology

Energy Technology Data Exchange (ETDEWEB)

Lee, Byung Jik; Kwon, H S; Kim, G N. and others

1999-03-01

Through the project of 'Development of decontamination, decommissioning and environmental restoration technology', the followings were studied. 1. Development of decontamination and repair technology for nuclear fuel cycle facilities 2. Development of dismantling technology 3. Development of environmental restoration technology. (author)

Development of decontamination, decommissioning and environmental restoration technology

International Nuclear Information System (INIS)

Lee, Byung Jik; Kwon, H. S.; Kim, G. N. and others

1999-03-01

Through the project of D evelopment of decontamination, decommissioning and environmental restoration technology , the followings were studied. 1. Development of decontamination and repair technology for nuclear fuel cycle facilities 2. Development of dismantling technology 3. Development of environmental restoration technology. (author)

Development of decontamination, decommissioning and environmental restoration technology

Energy Technology Data Exchange (ETDEWEB)

Lee, Byung Jik; Kwon, H. S.; Kim, G. N. and others

1999-03-01

Through the project of 'Development of decontamination, decommissioning and environmental restoration technology', the followings were studied. 1. Development of decontamination and repair technology for nuclear fuel cycle facilities 2. Development of dismantling technology 3. Development of environmental restoration technology. (author)

Development of Nuclear Decontamination Technology Using Supercritical Fluid

Energy Technology Data Exchange (ETDEWEB)

Jung, Wonyoung; Park, Kwangheon; Park, Jihye; Lee, Donghee [Kyunghee Univ., Yongin (Korea, Republic of)

2014-05-15

Soil cleaning technologies that have been developed thus far increase treatment costs in contaminated soil recovery processes because they generate large amounts of secondary wastes. In this respect, this study is intended to develop soil decontamination methods using CO{sub 2}, which is a nontoxic, environmentally friendly substance, in order to fundamentally suppress the generation of secondary wastes from the decontamination process and to create high added values. In this study, to develop decontamination methods for uranium-contaminated soil using supercritical CO{sub 2}, a soil decontamination system using supercritical CO{sub 2} was constructed. In addition, the basic principle of supercritical CO{sub 2} decontamination using a TBP-HNO3 complex was explained. According to the results of the study, sea-sand samples having the same degree of contamination showed different results of decontamination according to the quantities of the TBP-HNO3 complex used as an extraction agent, which resulted in high extraction rates. Thus far, a most widely used method of extracting uranium has been the dissolving of uranium in acids. However, this method has the large adverse effect of generating strong acidic wastes that cannot be easily treated. On the other hand, supercritical CO{sub 2} requires critical conditions that are no more difficult to meet than those of other supercritical fluids, since its density can be changed from a very low state close to that of an ideal gas to a high state close to that of liquids. The critical gas conditions are a pressure of 71 bar and a temperature of 31 .deg. C, both of which are inexpensive to achieve. Moreover, CO{sub 2} is a solvent that is not harmful to the human body and few effects on environmental pollution. Therefore, nontoxic and environment friendly processes can be developed using supercritical CO{sub 2}. Supercritical CO{sub 2}'s advantages over prevailing methods suggest its potential for developing innovative

Development of Nuclear Decontamination Technology Using Supercritical Fluid

International Nuclear Information System (INIS)

Jung, Wonyoung; Park, Kwangheon; Park, Jihye; Lee, Donghee

2014-01-01

Soil cleaning technologies that have been developed thus far increase treatment costs in contaminated soil recovery processes because they generate large amounts of secondary wastes. In this respect, this study is intended to develop soil decontamination methods using CO 2 , which is a nontoxic, environmentally friendly substance, in order to fundamentally suppress the generation of secondary wastes from the decontamination process and to create high added values. In this study, to develop decontamination methods for uranium-contaminated soil using supercritical CO 2 , a soil decontamination system using supercritical CO 2 was constructed. In addition, the basic principle of supercritical CO 2 decontamination using a TBP-HNO3 complex was explained. According to the results of the study, sea-sand samples having the same degree of contamination showed different results of decontamination according to the quantities of the TBP-HNO3 complex used as an extraction agent, which resulted in high extraction rates. Thus far, a most widely used method of extracting uranium has been the dissolving of uranium in acids. However, this method has the large adverse effect of generating strong acidic wastes that cannot be easily treated. On the other hand, supercritical CO 2 requires critical conditions that are no more difficult to meet than those of other supercritical fluids, since its density can be changed from a very low state close to that of an ideal gas to a high state close to that of liquids. The critical gas conditions are a pressure of 71 bar and a temperature of 31 .deg. C, both of which are inexpensive to achieve. Moreover, CO 2 is a solvent that is not harmful to the human body and few effects on environmental pollution. Therefore, nontoxic and environment friendly processes can be developed using supercritical CO 2 . Supercritical CO 2 's advantages over prevailing methods suggest its potential for developing innovative decontamination methods, as demonstrated

Electrokinetic decontamination of concrete

Energy Technology Data Exchange (ETDEWEB)

Lomasney, H. [ISOTRON Corp., New Orleans, LA (United States)

1995-10-01

The U.S. Department of Energy has assigned a priority to the advancement of technology for decontaminating concrete surfaces which have become contaminated with radionuclides, heavy metals, and toxic organics. This agency is responsible for decontamination and decommissioning of thousands of buildings. Electrokinetic extraction is one of the several innovative technologies which emerged in response to this initiative. This technique utilizes an electropotential gradient and the subsequent electrical transport mechanism to cause the controlled movement of ionics species, whereby the contaminants exit the recesses deep within the concrete. This report discusses the technology and use at the Oak Ridge k-25 plant.

LCA of strippable coatings and of steam vacuum technology used for nuclear plants decontamination

International Nuclear Information System (INIS)

Guidi, Giambattista; Cumo, Fabrizio; Santoli, Livio de

2010-01-01

The application of strippable coatings is an innovative technology for decontamination of nuclear plants and for any decontamination project aiming at removing surface contamination. An adhesive plastic coating is applied on the contaminated surface. The strippable coating is allowed to cure for up to 24 h, after which it can be easily peeled. The coating traps the contaminants in the polymer matrix. Strippable coatings are non-toxic and do not contain volatile compounds or heavy metals. Since the coating constitutes a solid waste, disposal is easier than treating contaminated liquid wastes, produced by the baseline technology: steam vacuum cleaning, based upon superheated pressurized water in order to remove contaminants from floors and walls. A life cycle assessment (LCA) has been carried out with the purpose of comparing the strippable coating with the steam vacuum technology. The functional unit of the study is represented by a surface of 1 m 2 to be decontaminated. The results of LCA achieved using Sima Pro 5.0 registered software confirm the good environmental performances of strippable coatings. Taking into account both LCA and environmental costs for liquid wastes, the advantages of strippable coatings will be more and more evident. (orig.)

Report on practical use of new decontamination technology

International Nuclear Information System (INIS)

Nitta, Hideyuki; Ono, Masahiro

2000-03-01

For removing surface contamination of a solid waste with radioactivity, technology of laser cleaning and vacuum arc cleaning has the possibility to obtain the high decontamination rate. We made a research for practical uses of these methods as a new cleaning technology from published papers and patents. From these results, we discussed about an applicability of laser cleaning and vacuum arc cleaning to decontaminate a body of centrifugal separator. At first, we investigate the solid surface cleaning technology with a laser or a vacuum arc from published papers in the world and the patents in Japan. The results were listed in tables. Each information was abstracted into a technical data sheet and sorted into a related technology (system or equipment). We also investigate the decontamination technology by the same way and the results were abstracted into technical data sheets and sorted into related technologies, too. As an application of the above research, we considered the process and the system for decontaminating a body of centrifugal separators (cylinders). In the system, the cleaning head is set inside the cylinder and the inner surface contaminated by radioactivity is removed by the irradiation of a YAG laser, a CO2 laser or a vacuum arc. The cylinder is rotated by rotational rings and moved towards the direction of the central axis and the whole inner surface of the cylinder is cleaned with a constant cleaning rate. We also estimated the costs of each decontamination technology. (author)

Development of Decontamination and Decommissioning Technologies for Nuclear Facilities

International Nuclear Information System (INIS)

Moon, Jei Kwon; Lee, Kune Woo; Won, Hui Jun

2010-04-01

A laser ablation decontamination technology which is reportedly effective for a removal of fixed contaminants has been developed for three years as the first stage of the development. Lab scale experimental equipment was fabricated and the process variables have been assessed for determination of appropriate decontamination conditions at the laser wave lengths of 1,064 nm and 532 nm, respectively. The decontamination tests using radioactive specimens showed that the decontamination efficiency was about 100 which is quite a high value. An electrokinetic-flushing, an agglomeration leaching and a supercritical CO 2 soil decontamination technology were development for a decontamination of radioactive soil wastes from the decommissioned sites of the TRIGA research reactor and the uranium conversion facilities. An electrokinetic-flushing process was found to be effective for soil wastes aged for a long time and an agglomeration leaching process was effective for soil wastes of surface contamination. On the other hand, a supercritical CO 2 soil decontamination technology was found to be applicable for U or TRU bearing soil wastes. The remediation monitoring key technologies such as a representative sample taking and a measurement concept for the vertical distribution of radionuclides were developed for an assessment of the site remediation. Also an One-Dimensional Water Flow and Contaminant Transport in Unsaturated Zone (FTUNS) code was developed to interpretate the radionuclide migration in the unsaturated zone

Review of decontamination technologies for chemical counter-terrorism

Energy Technology Data Exchange (ETDEWEB)

Volchek, K.; Boudreau, L.; Hornof, M. [SAIC Canada, Ottawa, ON (Canada); Fingas, M.F.; Gamble, R.L. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Div]|[Environment Canada, Ottawa, ON (Canada). River Road Environmental Technology Centre

2004-07-01

The two categories of chemical agents that could be used in acts of chemical terrorism are conventional chemical warfare agents and commercial toxic chemicals. Industrial chemicals are easier to access than warfare agents, and must therefore be considered when evaluating decontamination techniques. This study involved a search of public-domain documents to identify decontamination technologies including: physical/mechanical treatment or removal; chemical treatment; and, biological methods including natural degradation and attenuation. The technologies were analyzed with reference to their effectiveness for specific groups of chemical agents, state of development, availability and costs. Results indicate that there are many decontamination methods available, both developed and under development, that work effectively for most agents. The two most common decontamination methods are oxidation and alkali hydrolysis followed by dehalogenation. Technology limitations and gaps were also identified, suggesting a need for more research to further the development of promising processes. 31 refs., 2 tabs.

Development of high-level radioactive waste treatment and conversion technologies 'Dry decontamination technology development for highly radioactive contaminants'

International Nuclear Information System (INIS)

Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. J.; Choi, W. K.; Kim, G. N.; Moon, J. K.

2001-04-01

The followings were studied through the project entitled 'Dry Decontamination Technology Development for Highly Radioactive Contaminants'. 1.Contaminant Characteristics Analysis of Domestic Nuclear Fuel Cycle Projects(NFCP) and Applicability Study of the Unit Dry-Decontamination Techniques A. Classification of contaminated equipments and characteristics analysis of contaminants B. Applicability study of the unit dry-decontamination techniques 2.Performance Evaluation of Unit Dry Decontamination Technique A. PFC decontamination technique B. CO2 decontamination technique C. Plasma decontamination technique 3.Development of Residual Radiation Assessment Methodology for High Radioactive Facility Decontamination A. Development of radioactive nuclide diffusion model on highly radioactive facility structure B. Obtainment of the procedure for assessment of residual radiation dose 4.Establishment of the Design Concept of Dry Decontamination Process Equipment Applicable to Highly Radioactive Contaminants 5.TRIGA soil unit decontamination technology development A. Development of soil washing and flushing technologies B. Development of electrokinetic soil decontamination technology

Cost Savings through Innovation in Decontamination, Decommissioning, and Dismantlement

International Nuclear Information System (INIS)

Yancey, Neal A.

2003-01-01

The United States Department of Energy (DOE) continually seeks safer and more cost effective technologies for the decontamination and decommissioning (D and D) of nuclear facilities. The Deactivation and Decommissioning Focus Area (DDFA) of the DOE's Office of Science and Technology (OST) sponsored large-scale demonstration and deployment projects (LSDDPs) to help bring new technologies into the D and D programs. The Idaho National Engineering and Environmental Laboratory (INEEL) LSDDP generated a list of needs defining specific problems where improved technologies could be incorporated into ongoing D and D tasks. The needs fell into 5 major categories--characterization, dismantlement, safety, material dispositioning, and decontamination. Technologies were carefully selected that provide a large benefit for a small investment. The technologies must provide significant improvements in cost, safety, radiation exposure, waste volume reduction, or schedule savings and widely applicable throughout the DOE complex. The LSDDP project provided training for the new technologies and worked with technology suppliers to resolve any questions that arose. Since 1998, 26 technologies have been demonstrated or deployed through the LSDDP for the D and D program at the INEEL. Of the 26 demonstrated and deployed technologies, 14 were in characterization, 3 were in decontamination, 4 were in dismantlement, 3 were in safety, and 2 were in material dispositioning. To promote the use of these technologies at other sites within the DOE complex, the LSDDP team published fact sheets, videos, technology summary reports, articles in INEEL star newspaper, posters, and maintained an internet home page on the project. As a result, additional deployments have taken place at the Hanford, Mound, Fernald, Oak Ridge, Ashtabula, and West Valley. Eight of the 26 technologies evaluated were developed in foreign countries. The technologies demonstrated have been shown to be faster, less expensive, and

En-Vac Robotic Wall Scabbler. Innovative Technology Summary Report

International Nuclear Information System (INIS)

2001-01-01

The U.S. Department of Energy (DOE) continually seeks safer and more cost-effective technologies for use in decontamination and decommissioning (D and D) of nuclear facilities. To this end, the Deactivation and Decommissioning Focus Area (DDFA) of the DOE's Office of Science and Technology (OST) sponsors Large-Scale Demonstration and Deployment Projects (LSDDP). At these LSDDPs, developers and vendors of improved or innovative technologies showcase products that are potentially beneficial to DOE's projects and to others in the D and D community. Benefits sought include decreased health and safety risks to personnel and the environment, increased productivity, and decreased cost of operation. The Idaho National Engineering and Environmental Laboratory (INEEL) LSDDP generated a list of statements defining specific needs or problems where improved technology could be incorporated into ongoing D and D tasks. One of the stated needs was for a Robotic Wall Scabbler that would reduce costs and shorten schedules in DOE's Decommissioning Project. This demonstration investigated the associated costs and time required to remove paint from the Test Area North (TAN-607) Decontamination Shop walls by comparing the En-vac Robotic Wall Scabbler against the baseline technology. The baseline technologies consist of the Pentek Vac Pac System with the Pentek Rotopeen and Needle Gun hand-held attachments. This system only removes paint from the surface of concrete. Innovative Technology The En-vac Robotic Wall Scabbler is a remote-controlled scabbling unit with individually motor-controlled wheels that moves horizontally and vertically along floors, walls, and ceilings, adhering to the surface with the help of a high-vacuum suction created at its base (see Figures 1 and 2). The complete En-vac Blasting System consists of the En-vac robot, a recycling unit, a filter, and a vacuum unit, and uses an abrasive, steel-grit blasting technology for the scabbling process. By comparison, this

Decision Analysis Modeling for Application and Fielding Selection Applied to Concrete Decontamination Technologies

International Nuclear Information System (INIS)

Ebadian, M.A.; Boudreaux, J.F.

1998-01-01

The purpose of this two-year investigation is to field test innovative technologies for coating and surface removal on concrete floors and compare the compiled data to baseline technologies, thereby ensuring that the best and most cost-effective options are developed and subsequently used during the decontamination and decommissioning (D and D) of U.S. Department of Energy Environmental Management (DOE-EM) sites. Comprehensive and comparable data will be collected in the areas of health and safety, operations, and secondary waste management. The technologies tested will include DOE-EM funded technologies and commercial non-nuclear technologies that have the potential to meet the environmental restoration objectives. This report summarizes the activities performed during Fiscal Year 1996 (FY96) and describes the planned activities for Fiscal Year 1997 (FY97). Accomplishments for FY96 include the completion of preparatory work to begin field testing of innovative technologies. A total of seven technologies will be tested during FY97. As a part of this project, interactive computer software will be developed during FY97, allowing site-specific parameters and technology performance data to be considered when determining the best option given site-specific conditions

Decontamination Technology Development for Nuclear Research Facilities

International Nuclear Information System (INIS)

Choi, W. K.; Jung, C. H.; Oh, W. Z.

2007-06-01

The originative CO 2 pellet blasting equipment was developed by improving additional components such as feed screw, idle roller and air-lock feeder to clear up the problems of freezing and discontinuity of blasting and by adopting pneumatically operated vacuum suction head and vacuum cup to prevent recontamination by collecting contaminant particulates simultaneously with the decontamination. The optimum decontamination process was established according to the kind of materials such as metal, concrete and plastic and the type of contaminants such as particulate, fixed chemical compound and oil. An excellent decontamination performances were verified by means of the lab-scale hot test with radioactive specimen and the technology demonstration in IMEF hot cell. The PFC dry decontamination equipment applicable to the surface contaminated with high radioactive particulate was developed. This equipment consists of the unit processes such as spray, collection, filtration and dry distillation designed originatively applicable to inside of dry hot cell. Through the demonstration of PFC spray decontamination process in IMEF hot cell, we secured on-site applicability and the decontamination efficiency more than 90 %. We investigated the characteristics of dismantled metal waste melting and the radionuclide(Co, Cs, U) distribution into ingot and slag by melting decontamination experiments using electric arc melter. We obtained the decontamination factors greater than 100 for Cs and of 10∼100 for uranium. The pilot scale(200 kg/batch) demonstration for melting decontamination was carried out successfully using high temperature melting facility at KAERI. The volume reduction factor of 1/7 and the economical feasibility of the melting decontamination were verified.

Development of high-level radioactive waste treatment and conversion technologies 'Dry decontamination technology development for highly radioactive contaminants'

Energy Technology Data Exchange (ETDEWEB)

Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. J.; Choi, W. K.; Kim, G. N.; Moon, J. K

2001-04-01

The followings were studied through the project entitled 'Dry Decontamination Technology Development for Highly Radioactive Contaminants'. 1.Contaminant Characteristics Analysis of Domestic Nuclear Fuel Cycle Projects(NFCP) and Applicability Study of the Unit Dry-Decontamination Techniques A. Classification of contaminated equipments and characteristics analysis of contaminants B. Applicability study of the unit dry-decontamination techniques 2.Performance Evaluation of Unit Dry Decontamination Technique A. PFC decontamination technique B. CO2 decontamination technique C. Plasma decontamination technique 3.Development of Residual Radiation Assessment Methodology for High Radioactive Facility Decontamination A. Development of radioactive nuclide diffusion model on highly radioactive facility structure B. Obtainment of the procedure for assessment of residual radiation dose 4.Establishment of the Design Concept of Dry Decontamination Process Equipment Applicable to Highly Radioactive Contaminants 5.TRIGA soil unit decontamination technology development A. Development of soil washing and flushing technologies B. Development of electrokinetic soil decontamination technology.

2-D linear motion system. Innovative technology summary report

International Nuclear Information System (INIS)

1998-11-01

The US Department of Energy's (DOE's) nuclear facility decontamination and decommissioning (D and D) program requires buildings to be decontaminated, decommissioned, and surveyed for radiological contamination in an expeditious and cost-effective manner. Simultaneously, the health and safety of personnel involved in the D and D activities is of primary concern. D and D workers must perform duties high off the ground, requiring the use of manlifts or scaffolding, often, in radiologically or chemically contaminated areas or in areas with limited access. Survey and decontamination instruments that are used are sometimes heavy or awkward to use, particularly when the worker is operating from a manlift or scaffolding. Finding alternative methods of performing such work on manlifts or scaffolding is important. The 2-D Linear Motion System (2-D LMS), also known as the Wall Walker trademark, is designed to remotely position tools and instruments on walls for use in such activities as radiation surveys, decontamination, and painting. Traditional (baseline) methods for operating equipment for these tasks require workers to perform duties on elevated platforms, sometimes several meters above the ground surface and near potential sources of contamination. The Wall Walker 2-D LMS significantly improves health and safety conditions by facilitating remote operation of equipment. The Wall Walker 2-D LMS performed well in a demonstration of its precision, accuracy, maneuverability, payload capacity, and ease of use. Thus, this innovative technology is demonstrated to be a viable alternative to standard methods of performing work on large, high walls, especially those that have potential contamination concerns. The Wall Walker was used to perform a final release radiological survey on over 167 m 2 of walls. In this application, surveying using a traditional (baseline) method that employs an aerial lift for manual access was 64% of the total cost of the improved technology. However

Technology development and demonstration for TRIGA research reactor decontamination, decommissioning and site restoration

International Nuclear Information System (INIS)

Oh, Won Zin; Jung, Ki Jung; Lee, Byung Jik

1997-01-01

This paper describes the introduction to research reactor decommissioning plan at KAERI, the background of technology development and demonstration, and the current status of the system decontamination technology for TRIGA reactors, concrete decontamination and dust treatment technologies, wall ranging robot and graphic simulation of dismantling processes, soil decontamination and restoration technology, recycling or reuse technologies for radioactive metallic wastes, and incineration technology demonstration for combustible wastes. 9 figs

Decontamination technology assessment

International Nuclear Information System (INIS)

Allen, R.P.; Konzek, G.J.; Schneider, K.R.; Smith, R.I.

1988-10-01

This study identifies and technically assesses foreign decontamination and decommissioning (D and D) technology developments that may represent significant improvements over D and D technology currently available or under development in the United States. Technology need areas for nuclear power reactor decommissioning operations were identified and prioritized using the results of past light water reactor (LWR) decommissioning studies to quantitatively evaluate the potential for reducing cost and decommissioning worker radiation dose for each major decommissioning activity. Based on these identified needs, current foreign D and D technologies of potential interest to the US were identified through personal contacts and the collection and review of an extensive body of D and D literature. These technologies were then assessed qualitatively to evaluate their uniqueness, potential for a significant reduction in D and D costs and/or worker radiation dose, development status, and other factors affecting their value and applicability to US needs. 4 refs

Radioactive scrap metal decontamination technology assessment report

International Nuclear Information System (INIS)

Buckentin, J.M.; Damkroger, B.K.; Schlienger, M.E.

1996-04-01

Within the DOE complex there exists a tremendous quantity of radioactive scrap metal. As an example, it is estimated that within the gaseous diffusion plants there exists in excess of 700,000 tons of contaminated stainless steel. At present, valuable material is being disposed of when it could be converted into a high quality product. Liquid metal processing represents a true recycling opportunity for this material. By applying the primary production processes towards the material's decontamination and re-use, the value of the strategic resource is maintained while drastically reducing the volume of material in need of burial. Potential processes for the liquid metal decontamination of radioactively contaminated metal are discussed and contrasted. Opportunities and technology development issues are identified and discussed. The processes compared are: surface decontamination; size reduction, packaging and burial; melting technologies; electric arc melting; plasma arc centrifugal treatment; air induction melting; vacuum induction melting; and vacuum induction melting and electroslag remelting

Reactor surface contamination stabilization. Innovative technology summary report

International Nuclear Information System (INIS)

1998-11-01

Contaminated surfaces, such as the face of a nuclear reactor, need to be stabilized (fixed) to avoid airborne contamination during decontamination and decommissioning activities, and to prepare for interim safe storage. The traditional (baseline) method of fixing the contamination has been to spray a coating on the surfaces, but ensuring complete coverage over complex shapes, such as nozzles and hoses, is difficult. The Hanford Site C Reactor Technology Demonstration Group demonstrated innovative technologies to assess stabilization properties of various coatings and to achieve complete coverage of complex surfaces on the reactor face. This demonstration was conducted in two phases: the first phase consisted of a series of laboratory assessments of various stabilization coatings on metal coupons. For the second phase, coatings that passed the laboratory tests were applied to the front face of the C Reactor and evaluated. The baseline coating (Rust-Oleum No. 769) and one of the innovative technologies did not completely cover nozzle assemblies on the reactor face, the most critical of the second-phase evaluation criteria. However, one of the innovative coating systems, consisting of a base layer of foam covered by an outer layer of a polymeric film, was successful. The baseline technology would cost approximately 33% as much as the innovative technology cost of $64,000 to stabilize an entire reactor face (196 m 2 or 2116 ft 2 ) with 2,004 nozzle assemblies, but the baseline system failed to provide complete surface coverage

Decontamination of process equipment using recyclable chelating solvent

Energy Technology Data Exchange (ETDEWEB)

Jevec, J.; Lenore, C.; Ulbricht, S. [Babcock & Wilcox, Co., R& DD, Alliance, OH (United States)

1995-10-01

The Department of Energy (DOE) is now faced with the task of meeting decontamination and decommissioning obligations at numerous facilities by the year 2019. Due to the tremendous volume of material involved, innovative decontamination technologies are being sought that can reduce the volumes of contaminated waste materials and secondary wastes requiring disposal. This report describes the results of the performance testing of chelates and solvents for the dissolution of uranium.

Comprehensive investigation of the corrosion and surface chemical effects of the decontamination technologies

International Nuclear Information System (INIS)

Szabo-Nagy, Andrea; Varga, Kalman; Deak-Horvath, Emese; Nemeth, Zoltan; Horvath, David; Schunk, Janos; Patek, Gabor

2012-09-01

Decontamination technologies are mainly developed to reduce the collective dose of the maintenance personnel at NPPs. The highest efficiency (i.e., the highest DF values) available without detrimental modification of the treated surface of structural material is the most important goal in the course of the application of a decontamination technology. A so-called 'soft' chemical decontamination technology has been developed - supported by the Paks Nuclear Power Plant - at the Institute of Radiochemistry and Radioecology of the University of Pannonia. The novel base technology can be effectively applied for the decontamination of the heat exchanger tubes of steam generators. In addition, by optimizing the main technological parameters (temperature, concentration of the liquid chemicals, flow rates, contact time, etc.) it can be utilized for specific applications such as decontamination of some dismountable devices and separable equipment or the total decontamination prior to plant dismantling (decommissioning) in the future. The aim of this work is to compare the efficiency, corrosion and surface chemical effects of some improved versions of the novel base-technology elaborated for decontamination of austenitic stainless steel surfaces. The experiments have been performed at laboratory conditions in decontamination model systems. The applied methods: γ-spectrometry, ICP-OES, voltammetry and SEM-EDX. The experimental results revealed that the efficiency of the base-technology mainly depends on the surface features of the stainless steel samples such as the chemical composition and thickness of the oxide layer, the nature (quantity, morphology and chemical composition) of the crystalline deposits. It has been documented that the improved version of the base-technology are suitable for the decontamination of both steel surfaces covered by chemically resistant large Cr-content crystals and that having compact oxide-layers (up to a thickness of 10 �

Decontamination Technologies, Task 3, Urban Remediation and Response Project

International Nuclear Information System (INIS)

Heiser, J.; Sullivan, T.

2009-01-01

In the aftermath of a Radiological Dispersal Device (RDD, also known as a dirty bomb) it will be necessary to remediate the site including building exteriors and interiors, equipment, pavement, vehicles, personal items etc. Remediation will remove or reduce radioactive contamination from the area using a combination of removing and disposing of many assets (including possible demolition of buildings), decontaminating and returning to service other assets, and fixing in place or leaving in place contamination that is deemed 'acceptable'. The later will require setting acceptable dose standards, which will require negotiation with all involved parties and a balance of risk and cost to benefit. To accomplish the first two, disposal or decontamination, a combination of technologies will be deployed that can be loosely classified as: Decontamination; Equipment removal and size reduction; and Demolition. This report will deal only with the decontamination technologies that will be used to return assets to service or to reduce waste disposal. It will not discuss demolition, size reduction or removal technologies or equipment (e.g., backhoe mounted rams, rock splitter, paving breakers and chipping hammers, etc.). As defined by the DOE (1994), decontamination is removal of radiological contamination from the surfaces of facilities and equipment. Expertise in this field comes primarily from the operation and decommissioning of DOE and commercial nuclear facilities as well as a small amount of ongoing research and development closely related to RDD decontamination. Information related to decontamination of fields, buildings, and public spaces resulting from the Goiania and Chernobyl incidents were also reviewed and provide some meaningful insight into decontamination at major urban areas. In order to proceed with decontamination, the item being processed needs to have an intrinsic value that exceeds the cost of the cleaning and justifies the exposure of any workers during the

Decontamination Technologies, Task 3, Urban Remediation and Response Project

Energy Technology Data Exchange (ETDEWEB)

Heiser,J.; Sullivan, T.

2009-06-30

In the aftermath of a Radiological Dispersal Device (RDD, also known as a dirty bomb) it will be necessary to remediate the site including building exteriors and interiors, equipment, pavement, vehicles, personal items etc. Remediation will remove or reduce radioactive contamination from the area using a combination of removing and disposing of many assets (including possible demolition of buildings), decontaminating and returning to service other assets, and fixing in place or leaving in place contamination that is deemed 'acceptable'. The later will require setting acceptable dose standards, which will require negotiation with all involved parties and a balance of risk and cost to benefit. To accomplish the first two, disposal or decontamination, a combination of technologies will be deployed that can be loosely classified as: Decontamination; Equipment removal and size reduction; and Demolition. This report will deal only with the decontamination technologies that will be used to return assets to service or to reduce waste disposal. It will not discuss demolition, size reduction or removal technologies or equipment (e.g., backhoe mounted rams, rock splitter, paving breakers and chipping hammers, etc.). As defined by the DOE (1994), decontamination is removal of radiological contamination from the surfaces of facilities and equipment. Expertise in this field comes primarily from the operation and decommissioning of DOE and commercial nuclear facilities as well as a small amount of ongoing research and development closely related to RDD decontamination. Information related to decontamination of fields, buildings, and public spaces resulting from the Goiania and Chernobyl incidents were also reviewed and provide some meaningful insight into decontamination at major urban areas. In order to proceed with decontamination, the item being processed needs to have an intrinsic value that exceeds the cost of the cleaning and justifies the exposure of any workers

Glovebox decontamination technology comparison

International Nuclear Information System (INIS)

Quintana, D.M.; Rodriguez, J.B.; Cournoyer, M.E.

1999-01-01

Reconfiguration of the CMR Building and TA-55 Plutonium Facility for mission requirements will require the disposal or recycle of 200--300 gloveboxes or open front hoods. These gloveboxes and open front hoods must be decontaminated to meet discharge limits for Low Level Waste. Gloveboxes and open front hoods at CMR have been painted. One of the deliverables on this project is to identify the best method for stripping the paint from large numbers of gloveboxes. Four methods being considered are the following: conventional paint stripping, dry ice pellets, strippable coatings, and high pressure water technology. The advantages of each technology will be discussed. Last, cost comparisons between the technologies will be presented

Decontamination technology assessment

International Nuclear Information System (INIS)

Allen, R.P.; Konzek, G.J.; Schneider, K.J.; Smith, R.I.

1988-01-01

This study was conducted by the Pacific Northwest Laboratory (PNL) for the U.S. Department of Energy (DOE) to identify and technically assess foreign decontamination and decommissioning (D and D) technology developments that may represent significant improvements over D and D technology currently available or under development in the United States. Technology need areas for nuclear power reactor decommissioning operations were identified and prioritized using the results of past light water rector (LWR) decommissioning studies to quantitatively evaluate the potential for reducing cost and decommissioning worker radiation dose for each major decommissioning activity. Based on these identified needs, current foreign D and D technologies of potential interest to the U.S. were identified through personal contacts and the collection and review of an extensive body of D and D literature. These technologies were then assessed qualitatively to evaluate their uniqueness, potential for a significant reduction in D and D costs and/or worker radiation dose, development status, and other factors affecting their value and applicability to U.S. needs

History of electric power technological innovation in 2017

International Nuclear Information System (INIS)

Yamaguchi, Hiroshi; Okabe, Kazuhiko; Ichimura, Yasunori

2017-01-01

This is an overview of the electric power technology innovation of 12 electric power companies in 2016. Among them, this paper outlines the technological contents related to nuclear power of three major companies. TEPCO group applied a sealant from the outside to the back-up seal of reactor containment vessel that had deteriorated. It developed a good sealing system by combining with an improved sealant, and confirmed the effect at an experimental level. Regarding environmental restoration in Fukushima, TEPCO developed a personal dosimetry technology, environmental monitoring technology, and a technology to simulate radiation reduction amount after decontamination. Chubu Electric Power Company conducted researches on the applicability of the start-up range neutron monitor count rate prediction method related to fuel loading after a long-term shut-down of nuclear power generation, basic examination for practical use of laser decontamination, and possibility of tsunami prediction using satellite positioning information. With regard to the decommissioning measures of nuclear power plants, Japan Nuclear Power Electric Generation Co., Ltd. conducted studies on the decommissioning work of the Tokai Power Station, the safe dismantling method of the Tsuruga Power Station Unit 1 as decommissioning measures and fuel management, and the disposal method of radioactive contaminants. In the development of future reactor, this company conducted research on the development of fast breeder reactor system, etc. (A.O.)

Decomposition Technology Development of Organic Component in a Decontamination Waste Solution

International Nuclear Information System (INIS)

Jung, Chong Hun; Oh, W. Z.; Won, H. J.; Choi, W. K.; Kim, G. N.; Moon, J. K.

2007-11-01

Through the project of 'Decomposition Technology Development of Organic Component in a Decontamination Waste Solution', the followings were studied. 1. Investigation of decontamination characteristics of chemical decontamination process 2. Analysis of COD, ferrous ion concentration, hydrogen peroxide concentration 3. Decomposition tests of hardly decomposable organic compounds 4. Improvement of organic acid decomposition process by ultrasonic wave and UV light 5. Optimization of decomposition process using a surrogate decontamination waste solution

Decomposition Technology Development of Organic Component in a Decontamination Waste Solution

Energy Technology Data Exchange (ETDEWEB)

Jung, Chong Hun; Oh, W. Z.; Won, H. J.; Choi, W. K.; Kim, G. N.; Moon, J. K

2007-11-15

Through the project of 'Decomposition Technology Development of Organic Component in a Decontamination Waste Solution', the followings were studied. 1. Investigation of decontamination characteristics of chemical decontamination process 2. Analysis of COD, ferrous ion concentration, hydrogen peroxide concentration 3. Decomposition tests of hardly decomposable organic compounds 4. Improvement of organic acid decomposition process by ultrasonic wave and UV light 5. Optimization of decomposition process using a surrogate decontamination waste solution.

Thermal decontamination of transformers: A new technology

International Nuclear Information System (INIS)

Colak, P.Z.

1992-01-01

After evaluating a number of methods for decontaminating or disposing of transformers that contained polychlorinated biphenyls (PCB), it was concluded that no entirely satisfactory procedure or technology was yet available which was permanent, effective, safe, relatively simple, and based on proven technology or conventional practice. The most desirable compromise appears to be thermal decontamination. It is proposed to decontaminate transformers by controlled incineration in a specially designed, indirect-fired furnace which resembles the conventional bell-type, vertical elevator, metal heat treating type of furnace. The design differs in the incorporation of those essential features required to achieve oxidation of the organic components, to provide internal air circulation needed to ensure efficient heat and mass transfer, and other factors. The most appropriate decontamination facility would provide for implementation of the following procedures: draining of PCB-containing liquids from the transformer; limited disassembly of the transformer, which in most instances would imply only removal of the top cover to expose the insides; and controlled incineration with any vapors generated being conducted to a secondary combustion chamber. Experiments were conducted in a kiln to simulate the proposed transformer incinerator. Results show that exposure of the transformer segments to a temperature in the 950-1,000 degree C range for over 90 min is generally sufficient to reduce the PCB content to under 1 ppM. Based on the work conducted, a suitable bell furnace was constructed and added to the Swan Hills (Alberta) waste treatment facility. 2 figs., 3 tabs

Y-12 Plant decontamination and decommissioning technology logic diagram for Building 9201-4. Volume 3: Technology evaluation data sheets; Part B: Decontamination, robotics/automation, waste management

International Nuclear Information System (INIS)

1994-09-01

The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 (TLD) was developed to provide a decision-support tool that relates decontamination and decommissioning (D and D) problems at Bldg. 9201-4 to potential technologies that can remediate these problems. The TLD uses information from the Strategic Roadmap for the Oak Ridge Reservation, the Oak Ridge K-25 Site Technology Logic Diagram, the Oak Ridge National Laboratory Technology Logic Diagram, and a previous Hanford logic diagram. This TLD identifies the research, development, demonstration, testing, and evaluation needed for sufficient development of these technologies to allow for technology transfer and application to D and D and waste management (WM) activities. It is essential that follow-on engineering studies be conducted to build on the output of this project. These studies will begin by selecting the most promising technologies identified in the TLD and by finding an optimum mix of technologies that will provide a socially acceptable balance between cost and risk. This report consists of the decontamination, robotics/automation, and WM data sheets

Investigation on safety of gel decontamination technology

International Nuclear Information System (INIS)

Liu Zhihui; Song Fengli; Wang Yongxian; Zhang Taoge

2014-01-01

Gel decontamination technology is an advanced decontamination process of metal contaminated by radionuclide. It has the advantages such as simple operation process, high decontaminating factor, etc. But the disadvantages are that it has high spraying pressure and is strongly corrosive, which has safety risk to the operator and equipment. The effect of such factors as spraying pressure on operators was analyzed based on process feature, and it is proposed that it be worthwhile to make further study on the corrosion of gels to spraying equipment, taking into account corrosion feature of gels to stainless steel. Meanwhile, the safety issue was demonstrated on collecting and handling wastes from gel decontamination process. And then, protective measures, study methods, and solutions are put forward. The results show that protection should be strengthened during spraying to reduce the effect of splashing and fogging on workers; the equipment should be cleaned in time to reduce the effect of corrosion, and reducers should be added into waste liquid to eliminate the effect of residual detergent. (authors)

Assessment, evaluation, and testing of technologies for environmental restoration, decontamination, and decommissioning and high level waste management. Progress report

International Nuclear Information System (INIS)

Uzochukwu, G.A.

1997-01-01

Nuclear and commercial non-nuclear technologies that have the potential of meeting the environmental restoration, decontamination and decommissioning, and high-level waste management objectives are being assessed and evaluated. A detailed comparison of innovative technologies available will be performed to determine the safest and most economical technology for meeting these objectives. Information derived from this effort will be matched with the multi-objectives of the environmental restoration, decontamination and decommissioning, and high-level waste management effort to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the safest and most economical technologies are developed for use at SRS and other DOE sites

Assessment, evaluation, and testing of technologies for environmental restoration, decontamination, and decommissioning and high level waste management. Progress report

Energy Technology Data Exchange (ETDEWEB)

Uzochukwu, G.A.

1997-12-31

Nuclear and commercial non-nuclear technologies that have the potential of meeting the environmental restoration, decontamination and decommissioning, and high-level waste management objectives are being assessed and evaluated. A detailed comparison of innovative technologies available will be performed to determine the safest and most economical technology for meeting these objectives. Information derived from this effort will be matched with the multi-objectives of the environmental restoration, decontamination and decommissioning, and high-level waste management effort to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the safest and most economical technologies are developed for use at SRS and other DOE sites.

Study of decontamination and waste management technologies for contaminated rural and forest environment

International Nuclear Information System (INIS)

Grebenkov, A.; Davydchuk, V.; Firsakova, S.; Jouve, A.; Kutlakhmedov, Y.; Rose, K.; Zhouchenko, T.; Antzypaw, G.

1996-01-01

Pilot and demonstrative scale in situ trials of several decontamination technologies proposed in the framework of ECP-4 project were carried out in real conditions of Chernobyl Zone. Their results proved that industrial scale decontamination of various types of land is feasible. The management of radioactive waste arising from decontamination techniques can be provided by ecologically sound and efficient technologies

Efficacy of liquid and foam decontamination technologies for chemical warfare agents on indoor surfaces.

Science.gov (United States)

Love, Adam H; Bailey, Christopher G; Hanna, M Leslie; Hok, Saphon; Vu, Alex K; Reutter, Dennis J; Raber, Ellen

2011-11-30

Bench-scale testing was used to evaluate the efficacy of four decontamination formulations on typical indoor surfaces following exposure to the liquid chemical warfare agents sarin (GB), soman (GD), sulfur mustard (HD), and VX. Residual surface contamination on coupons was periodically measured for up to 24h after applying one of four selected decontamination technologies [0.5% bleach solution with trisodium phosphate, Allen Vanguard Surface Decontamination Foam (SDF™), U.S. military Decon Green™, and Modec Inc. and EnviroFoam Technologies Sandia Decontamination Foam (DF-200)]. All decontamination technologies tested, except for the bleach solution, performed well on nonporous and nonpermeable glass and stainless-steel surfaces. However, chemical agent residual contamination typically remained on porous and permeable surfaces, especially for the more persistent agents, HD and VX. Solvent-based Decon Green™ performed better than aqueous-based bleach or foams on polymeric surfaces, possibly because the solvent is able to penetrate the polymer matrix. Bleach and foams out-performed Decon Green for penetrating the highly polar concrete surface. Results suggest that the different characteristics needed for an ideal and universal decontamination technology may be incompatible in a single formulation and a strategy for decontaminating a complex facility will require a range of technologies. Copyright © 2011 Elsevier B.V. All rights reserved.

Technology for treatment of decontamination products

International Nuclear Information System (INIS)

Kavkhuta, G.A.; Rozdzyalovskaya, L.F.

1994-01-01

The research concerning the methods of management and processing of products generated as the result of post Chernobyl decontamination activities is being carried out by the Institute of Radioecological Problems of Belarus Academy of Science (IRP) in the framework of the Belarus National Programme. The main goal of this work is choice and development of an appropriate system for treatment of the decontamination radwastes, based on currently available information and experimental studies. This paper presents the technological schemes being studied for treating the post-Chernobyl liquid and solid wastes and will also briefly discuss the approach being used to settle a problem on collecting/management of low-level radioactive ash wastes, generated from the use of contaminated fuel

Innovative technologies for recycling and reusing radioactively contaminated materials from DOE facilities

International Nuclear Information System (INIS)

Bossart, S.J.; Hyde, J.

1993-01-01

Through award of ten contracts under the solicitation, DOE is continuing efforts to develop innovative technologies for decontamination and recycling or reusing of process equipment, scrap metal, and concrete. These ten technologies are describe briefly in this report. There is great economic incentive for recycling or reusing materials generated during D ampersand D of DOE's facilities. If successfully developed, these superior technologies will enable DOE to clean its facilities by 2019. These technologies will also generate a reusable or recyclable product, while achieving D ampersand D in less time at lower cost with reduced health and safety risks to the workers, the public and the environment

The integration of innovative technologies into a physical-separation-based soil washing system

International Nuclear Information System (INIS)

Krstich, M.A.

1995-01-01

An innovative system's approach to the treatment of soils at the Fernald Environmental Management Project (FEMP) has been proposed to effectively and cost competitively treat a significant mass of soil. The use of an integrated soil treatment system to decontaminate FEMP soils is a unique application of the soil washing technology. Due to the unfavorable soil particle size distribution and the ubiquitous distribution of uranium among these particle size fractions, conventional soil washing processes commonly used on predominantly sandy soils alone may not achieve the desirable waste minimization level without the inclusion of innovative technologies. This objective of this paper is to briefly describe the physical separation and chemical extraction process commonly used in soil washing operation and to present the baseline soil washing approach used on FEMP soils. Noting the successful and not-so-successful processes within the soil washing operation at the FEMP, a proposed innovative system's approach to treating FEMP soils will be described. This system's approach will integrate a conventional soil washing operation with proposed innovative technologies

Decontamination and decommissioning focus area. Technology summary

International Nuclear Information System (INIS)

1995-06-01

This report presents details of the facility deactivation, decommissioning, and material disposition research for development of new technologies sponsored by the Department of Energy. Topics discussed include; occupational safety, radiation protection, decontamination, remote operated equipment, mixed waste processing, recycling contaminated metals, and business opportunities

Development of waste minimization and decontamination technologies at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Ferguson, R.L.; Archibald, K.E.; Demmer, R.L.

1995-01-01

Emphasis on the minimization of decontamination secondary waste has increased because of restrictions on the use of hazardous chemicals and Idaho Chemical Processing Plant (ICPP) waste handling issues. The Lockheed Idaho Technologies Co. (LITCO) Decontamination Development Subunit has worked to evaluate and introduce new performed testing, evaluations, development and on-site demonstrations for a number of novel decontamination techniques that have not yet previously been used at the ICPP. This report will include information on decontamination techniques that have recently been evaluated by the Decontamination Development Subunit

Advance of technological innovations of electric power in 2012

International Nuclear Information System (INIS)

Mayumi, Akihiko; Tanaka, Masanori; Takebe, Toshiro

2013-01-01

Twelve companies in Japan reported on the technological innovations in 2012. The Japan Atomic Power Company mainly studied five projects; (1) control of wall thinning of the secondary system in PWR by injection of molybdic acid, (2) application of pipe test method using electromagnetic acoustic resonance to existing equipment, (3) developed high performance Co-60 crud removal resin for Tsuruga Power Station Unit 2, (4) improvement of technology for safety of core in FBR, and (5) improvement of technology for coolant of FBR by dispersing nano-particles in liquid sodium metal. Tokyo Electric Power Company developed mainly three projects; (1) the support for the mental health care activities by industry protection staff at the Fukushima Daiichi and Daini Nuclear Power Plant, (2) laboratory test method using non-radioactive cesium for performance of decontamination reagent, and (3) decontamination effects estimation code (DeConEP). Hokuriku Electric Power Company reported the operations management measures in accordance with the safety enhancement measures to Shika nuclear power station. Other nine reports are published by Hokkaido Electric Power Co., Inc. Tohoku Electric Power Co., Inc. Chubu Electric Power Co., Inc., The Kansai Electric Power Co., Inc., The Chugoku Electric Power Co., Inc., Shikoku Electric Power Co., Inc., Kyushu Electric Power Co., Inc., Okinawa Electric Power Company Inc. and J-Power. (S.Y.)

Analysis of the application of decontamination technologies to radioactive metal waste minimization using expert systems

Energy Technology Data Exchange (ETDEWEB)

Bayrakal, Suna [Iowa State Univ., Ames, IA (United States)

1993-09-30

Radioactive metal waste makes up a significant portion of the waste currently being sent for disposal. Recovery of this metal as a valuable resource is possible through the use of decontamination technologies. Through the development and use of expert systems a comparison can be made of laser decontamination, a technology currently under development at Ames Laboratory, with currently available decontamination technologies for applicability to the types of metal waste being generated and the effectiveness of these versus simply disposing of the waste. These technologies can be technically and economically evaluated by the use of expert systems techniques to provide a waste management decision making tool that generates, given an identified metal waste, waste management recommendations. The user enters waste characteristic information as input and the system then recommends decontamination technologies, determines residual contamination levels and possible waste management strategies, carries out a cost analysis and then ranks, according to cost, the possibilities for management of the waste. The expert system was developed using information from literature and personnel experienced in the use of decontamination technologies and requires validation by human experts and assignment of confidence factors to the knowledge represented within.

Analysis of the application of decontamination technologies to radioactive metal waste minimization using expert systems

International Nuclear Information System (INIS)

Bayrakal, S.

1993-01-01

Radioactive metal waste makes up a significant portion of the waste currently being sent for disposal. Recovery of this metal as a valuable resource is possible through the use of decontamination technologies. Through the development and use of expert systems a comparison can be made of laser decontamination, a technology currently under development at Ames Laboratory, with currently available decontamination technologies for applicability to the types of metal waste being generated and the effectiveness of these versus simply disposing of the waste. These technologies can be technically and economically evaluated by the use of expert systems techniques to provide a waste management decision making tool that generates, given an identified metal waste, waste management recommendations. The user enters waste characteristic information as input and the system then recommends decontamination technologies, determines residual contamination levels and possible waste management strategies, carries out a cost analysis and then ranks, according to cost, the possibilities for management of the waste. The expert system was developed using information from literature and personnel experienced in the use of decontamination technologies and requires validation by human experts and assignment of confidence factors to the knowledge represented within

A study on the applicability for primary system decontamination through analysis on NPP decommission technology and international experience

Energy Technology Data Exchange (ETDEWEB)

Song, Jong Soon; Jung, Min Young; Lee, Sang Heon [Chosun University, Gwangju (Korea, Republic of)

2016-03-15

Decontamination is one of the most important technologies for the decommissioning of NPP. The purpose of decontamination is to reduce the Risk of exposure of the decommissioning workers, and to recycle parts of the plant components. Currently, there is a lack of data on the efficiency of the decontamination technologies for decommissioning. In most cases, the local radiation level can be lowered below a regulatory limitation by decontamination. Therefore, more efficient decontamination technology must be continuously developed. This work describes the practical experiences in the United States and the European countries for NPP decommissioning using these decontamination technologies. When the decommissioning of domestic nuclear power plant is planned and implemented, this work will be helpful as a reference of previous cases.

Gaseous and air decontamination technologies for Clostridium difficile in the healthcare environment.

Science.gov (United States)

Davies, A; Pottage, T; Bennett, A; Walker, J

2011-03-01

The recent data for hospital-acquired infections suggest that infection rates for meticillin-resistant Staphylococcus aureus (MRSA) and Clostridium difficile are beginning to decrease. However, while there is still pressure to maintain this trend, the resistance of C. difficile spores to standard detergents continues to present a problem for many UK hospitals trying to prevent its spread or control outbreaks. Alternative disinfection technologies such as gaseous decontamination are currently being marketed to the healthcare sector as an alternative/supplement to manual disinfection, and have been shown to be effective in reducing environmental contamination. When used correctly, they offer a complementary technology to manual cleaning that increases the probability of an effective reduction in viability and provides a comparatively uniform distribution of disinfectant. Three gaseous decontamination technologies are examined for their suitability in reducing environmental contamination with C. difficile: gaseous hydrogen peroxide, chlorine dioxide and ozone. Air decontamination and UV-based technologies are also briefly described. We conclude that while there is a role to play for these new technologies in the decontamination of ward surfaces contaminated with C. difficile, the requirement for both a preclean before use and the limited 'in vivo' evidence means that extensive field trials are necessary to determine their cost-effectiveness in a healthcare setting. Copyright © 2010 The Hospital Infection Society. Published by Elsevier Ltd. All rights reserved.

Development of the Decontamination and Decommissioning Technology for Nuclear Facilities

International Nuclear Information System (INIS)

Lee, K. W.; Moon, J. K.; Won, C. H.

2010-04-01

The research results could be used for a design of a remote ablation decontamination system and ultimately applicable for an decontamination of high radiation facilities such as the DUPIC and PIEF. The evaluation technology of decommissioning process must be developed and will be used for the ALARA planning tool of decommissioning process and demonstrated for tools of decommissioning equipment. Also, this technology can be used for tools workplaces with high work difficulty such as large-scale chemical plant, under water and space. It is expected that the technology for a volume reduction and self-disposal of dismantled concrete wastes can be contributed to the establishment of a management plan for radioactive dismantled concrete wastes through the minimization of final waste volume

Development of decontamination technology for the decommissioned Bohunice A-1 nuclear power plant

International Nuclear Information System (INIS)

Krejci, F.; Majersky, D.; Solcanyi, M.; Sekely, S.; Kucharik, D.

1991-01-01

The main results of investigation into the decontamination technology for the equipment and buildings of the decommissioned A-1 nuclear power plant, achieved by the Nuclear Power Plants Research Institute in Trnava over the 1988-1990 period, are summarized. Mobile decontamination and recirculation equipment has been developed for pre-disassembling decontamination. A solution containing formic acid (19 g/l), EDTA-Na 4 (6 g/l) and thiourea (0.5 g/l) was used for decontamination of low-alloy steels; for materials from the steam generators and turbo-compressors, the decontamination factor (DF) of this solution was 30 to 150 per decontamination cycle. For high-alloy steels, a two-stage process comprising the use of an oxidation solution and a reduction solution appeared suitable. The oxidation solution contained potassium permanganate (0.6 g/l) and nitric acid (0.4 g/l), whereas the reduction solution, viz. Citrox 21, contained citric acid (0.5 g/l), oxalic acid (1.0 g/l) and EDTA-NA 4 (2.5 g/l). The DF is 10 to 50 in one oxidation-reduction cycle and 50-100 in two cycles. For the post-disassembling chemical decontamination, the contaminated material was cut into pieces 70 to 80 cm long, freed from grease and decontaminated chemically by submerging in the solution while applying treatment by ultrasound. A technology of electrochemical decontamination has also been developed. It appeared particularly suitable for structural materials of the primary coolant circuit comprising austenitic stainless steels and low-alloy steels after pre-disassembling chemical decontamination with remainders of the corrosion layer, and for structural materials of the secondary coolant circuit after chemical post-disassembling decontamination. Research in the field of decontamination of the building parts and of the outer surfaces of the structural materials concentrated mainly on the use of decontamination foams. Foaming solutions have been developed for the decontamination of PESL floors and

Study on LOMI decontamination technology

International Nuclear Information System (INIS)

Huang Fuduan; Yu Degui; Lu Jingju; Xie Yinyan

1993-10-01

The results of decontamination technique of Low-Oxidation-State Metal-Ion (LOMI) reagents developed from 1986 to 1991 in the laboratory are introduced. The experiments included preparation of LOMI reagents, de-filming efficiency, corrosion behavior of typical alloys, decontamination factors of reagents for contaminated materials and components have proved that the NP/LOMI decontamination method and treatment technique of waste water are feasible and have some advantages. The preparation of LOMI reagent with low concentration of formic acid by reduced pressure distilling technique and the utilization ratio of vanadium reached to 95% by second electrolysis are the main contributions of the study to the decontamination technique

Decontamination of Steam Generator tube using Abrasive Blasting Technology

International Nuclear Information System (INIS)

Min, B. Y.; Kim, G. N.; Choi, W. K.; Lee, K. W.; Kim, D. H.; Kim, K. H.; Kim, B. T.

2010-01-01

As a part of a technology development of volume reduction and self disposal for large metal waste project, We at KAERI and our Sunkwang Atomic Energy Safety (KAES) subcontractor colleagues are demonstrating radioactively contaminated steam generator tube by abrasive blasting technology at Kori-1 NPP. A steam generator is a crucial component in a PWR (pressurized Water Reactor). It is the crossing between the primary, contaminated, circuit and the secondary waste-steam circuit. The heat from the primary reactor coolant loop is transferred to the secondary side in thousands of small tubes. Due to several problems in the material of those tube, like SCC (Stress Corrosion Cracking), insufficient control in water chemistry, which can be cause of tube leakage, more and more steam generators are replaced today. Only in Korea, already 2 of them are replaced and will be replaced in the near future. The retired 300 ton heavy Steam generator was stored at the storage waste building of Kori NPP site. The steam generator waste has a large volume, so that it is necessary to reduce its volume by decontamination. A waste reduction effect can be obtained through decontamination of the inner surface of a steam generator. Therefore, it is necessary to develop an optimum method for decontamination of the inner surface of bundle tubes. The dry abrasive blasting is a very interesting technology for the realization of three-dimensional microstructures in brittle materials like glass or silicon. Dry abrasive blasting is applicable to most surface materials except those that might be shattered by the abrasive. It is most effective on flat surface and because the abrasive is sprayed and can also applicable on 'hard to reach' areas such as inner tube ceilings or behind equipment. Abrasive decontamination techniques have been applied in several countries, including Belgium, the CIS, France, Germany, Japan, the UK and the USA

Advanced technologies for decontamination and conversion of scrap metal

International Nuclear Information System (INIS)

Valerie MacNair; Steve Sarten; Thomas Muth; Brajendra Mishra

1999-01-01

The Department of Energy (DOE) faces the task of decommissioning much of the vast US weapons complex. One challenge of this effort includes the disposition of large amounts of radioactively contaminated scrap metal (RSM) including but not limited to steel, nickel, copper, and aluminum. The decontamination and recycling of RSM has become a key element in the DOE's strategy for cleanup of contaminated sites and facilities. Recycling helps to offset the cost of decommissioning and saves valuable space in the waste disposal facilities. It also reduces the amount of environmental effects associated with mining new metals. Work on this project is geared toward finding decontamination and/or recycling alternatives for the RSM contained in the decommissioned gaseous diffusion plants including approximately 40,000 tons of nickel. The nickel is contaminated with Technetium-99, and is difficult to remove using traditional decontamination technologies. The project, titled ''Advanced Technologies for Decontamination and Conversion of Scrap Metal'' was proposed as a four phase project. Phase 1 and 2 are complete and Phase 3 will complete May 31, 1999. Stainless steel made from contaminated nickel barrier was successfully produced in Phase 1. An economic evaluation was performed and a market study of potential products from the recycled metal was completed. Inducto-slag refining, after extensive testing, was eliminated as an alternative to remove technetium contamination from nickel. Phase 2 included successful lab scale and pilot scale demonstrations of electrorefining to separate technetium from nickel. This effort included a survey of available technologies to detect technetium in volumetrically contaminated metals. A new process to make sanitary drums from RSM was developed and implemented. Phase 3 included a full scale demonstration of electrorefining, an evaluation of electro-refining alternatives including direct dissolution, melting of nickel into anodes, a laser cutting

Industrialized Innovation: The Connection of Science & Technology Innovation with Industrial Innovation

Institute of Scientific and Technical Information of China (English)

Yinxing Hong; Yao Lu; Jianghuai Zheng

2017-01-01

In light of the relationship and the current disconnection between science & technology (S&T) innovation and industrial innovation in China,it is necessary to put forward and emphasize the concept of industrialized innovation.Industrialized innovation is the bridge and intermediation between S&T innovation and industrial innovation,which is not only a concept,but also a mechanism and combination force.There are two ways to achieve industrialized innovation:through industry-university-research coordination and through technology entrepreneurship.The meaning of industry-university-research coordination is not about coordination among industry,university and research sectors in an institutional sense;rather it is about the coordination of the functions of cultivation and development in new industries,new technologies,and new talents of industrialized innovation.The incentive mechanism for industrialized innovation should motivate not only innovation but also coordination.Technology entrepreneurship is the industrialization of new technology through business start-ups,which occurs beyond the stage of incubation and development of new technology.The capital of technology entrepreneurship is the set consisting of knowledge capital manifested through technological innovation,human capital manifested through entrepreneurs,and physical capital in the form of venture capital.While physical capital is indispensable,knowledge capital and human capital play the decisive role in technology entrepreneurship.The industrialization of technological innovation involves two requirements:one is to enable the new technology industry to achieve a large scale rapidly,and the other is to fully realize the potential value of the new technology.Both requirements are reliant on effective innovation in business models.

Decontamination & decommissioning focus area

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

In January 1994, the US Department of Energy Office of Environmental Management (DOE EM) formally introduced its new approach to managing DOE`s environmental research and technology development activities. The goal of the new approach is to conduct research and development in critical areas of interest to DOE, utilizing the best talent in the Department and in the national science community. To facilitate this solutions-oriented approach, the Office of Science and Technology (EM-50, formerly the Office of Technology Development) formed five Focus AReas to stimulate the required basic research, development, and demonstration efforts to seek new, innovative cleanup methods. In February 1995, EM-50 selected the DOE Morgantown Energy Technology Center (METC) to lead implementation of one of these Focus Areas: the Decontamination and Decommissioning (D & D) Focus Area.

Study and modelling of an innovative coprecipitation reactor for radioactive liquid wastes decontamination

International Nuclear Information System (INIS)

Flouret, Julie

2013-01-01

In order to decontaminate radioactive liquid wastes of low and intermediate levels, the coprecipitation is the process industrially used. The aim of this PhD work is to optimize the continuous process of coprecipitation. To do so, an innovative reactor is designed and modelled: the continuous reactor/classifier. Two model systems are studied: the coprecipitation of strontium by barium sulphate and the sorption of cesium by PPFeNi. The simulated effluent contains sodium nitrate in order to consider the high ionic strength of radioactive liquid wastes. First, each model system is studied on its own, and then a simultaneous treatment is performed. The kinetic laws of nucleation and crystal growth of barium sulphate are determined and incorporated into the coprecipitation model. Kinetic studies and sorption isotherms of cesium by PPFeNi are also performed in order to acquire the necessary data for process modelling. The modelling realised enables accurate prediction of the residual strontium and cesium concentrations according to the process used: it is a valuable tool for the optimization of existing units, but also the design of future units. The continuous reactor/classifier presents many advantages compared to the classical continuous process: the decontamination efficiency of strontium and cesium is highly improved while the volume of sludge generated by the process is reduced. A better liquid/solid separation is observed in the reactor/classifier and the global installation is significantly more compact. Thus, the radioactive liquid wastes treatment processes can be intensified by the continuous reactor/classifier, which represents a very promising technology for future industrial application. (author) [fr

Full system decontamination. AREVAs experience in decontamination prior to decommissioning

International Nuclear Information System (INIS)

Topf, Christian

2010-01-01

Minimizing collective radiation exposure and producing free-release material are two of the highest priorities in the decommissioning of a Nuclear Power Plant (NPP). Full System Decontamination (FSD) is the most effective measure to reduce source term and remove oxide layer contamination within the plant systems. FSD is typically a decontamination of the primary coolant circuit and the auxiliary systems. In recent years AREVA NP has performed several FSDs in PWRs and BWRs prior to decommissioning by applying the proprietary CORD copyright family and AMDA copyright technology. Chemical Oxidation Reduction Decontamination or CORD represents the chemical decontamination process while AMDA stands for Automated Mobile Decontamination Appliance, AREVA NPs decontamination equipment. Described herein are the excellent results achieved for the FSDs applied at the German PWRs Stade in 2004 and Obrigheim in 2007 and for the FSDs performed at the Swedish BWRs, Barsebaeck Unit 1 in 2007 and Barsebaeck Unit 2 in 2008. All four FSDs were performed using the AREVA NP CORD family decontamination technology in combination with the AREVA NP decontamination equipment, AMDA. (orig.)

Integration of improved decontamination and characterization technologies in the decommissioning of the CP-5 research reactor

International Nuclear Information System (INIS)

Bhattacharyya, S. K.; Boing, L. E.

2000-01-01

The aging of research reactors worldwide has resulted in a heightened awareness in the international technical decommissioning community of the timeliness to review and address the needs of these research institutes in planning for and eventually performing the decommissioning of these facilities. By using the reactors already undergoing decommissioning as test beds for evaluating enhanced or new/innovative technologies for decommissioning, it is possible that new techniques could be made available for those future research reactor decommissioning projects. Potentially, the new technologies will result in: reduced radiation doses to the work force, larger safety margins in performing decommissioning and cost and schedule savings to the research institutes in performing the decommissioning of these facilities. Testing of these enhanced technologies for decontamination, dismantling, characterization, remote operations and worker protection are critical to furthering advancements in the technical specialty of decommissioning. Furthermore, regulatory acceptance and routine utilization for future research reactor decommissioning will be assured by testing and developing these technologies in realistically contaminated environments prior to use in the research reactors. The decommissioning of the CP-5 Research Reactor is currently in the final phase of dismantlement. In this paper the authors present results of work performed at Argonne National Laboratory (ANL) in the development, testing and deployment of innovative and/or enhanced technologies for the decommissioning of research reactors

Y-12 Plant decontamination and decommissioning technology logic diagram for Building 9201-4. Volume 2: Technology logic diagram

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 (TLD) was developed to provide a decision-support tool that relates decontamination and decommissioning (D and D) problems at Bldg. 9201-4 to potential technologies that can remediate these problems. This TLD identifies the research, development, demonstration, testing, and evaluation needed for sufficient development of these technologies to allow for technology transfer and application to D and D and waste management (WM) activities. It is essential that follow-on engineering studies be conducted to build on the output of this project. These studies will begin by selecting the most promising technologies identified in the TLD and by finding an optimum mix of technologies that will provide a socially acceptable balance between cost and risk. The TLD consists of three fundamentally separate volumes: Vol. 1 (Technology Evaluation), Vol. 2 (Technology Logic Diagram), and Vol. 3 (Technology Evaluation Data Sheets). Volume 2 contains the logic linkages among environmental management goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 2 has been divided into five sections: Characterization, Decontamination, Dismantlement, Robotics/Automation, and Waste Management. Each section contains logical breakdowns of the Y-12 D and D problems by subject area and identifies technologies that can be reasonably applied to each D and D challenge.

Y-12 Plant decontamination and decommissioning technology logic diagram for Building 9201-4. Volume 2: Technology logic diagram

International Nuclear Information System (INIS)

1994-09-01

The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 (TLD) was developed to provide a decision-support tool that relates decontamination and decommissioning (D and D) problems at Bldg. 9201-4 to potential technologies that can remediate these problems. This TLD identifies the research, development, demonstration, testing, and evaluation needed for sufficient development of these technologies to allow for technology transfer and application to D and D and waste management (WM) activities. It is essential that follow-on engineering studies be conducted to build on the output of this project. These studies will begin by selecting the most promising technologies identified in the TLD and by finding an optimum mix of technologies that will provide a socially acceptable balance between cost and risk. The TLD consists of three fundamentally separate volumes: Vol. 1 (Technology Evaluation), Vol. 2 (Technology Logic Diagram), and Vol. 3 (Technology Evaluation Data Sheets). Volume 2 contains the logic linkages among environmental management goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 2 has been divided into five sections: Characterization, Decontamination, Dismantlement, Robotics/Automation, and Waste Management. Each section contains logical breakdowns of the Y-12 D and D problems by subject area and identifies technologies that can be reasonably applied to each D and D challenge

Surveillance and Measurement System (SAMS). Innovative Technology Summary Report

International Nuclear Information System (INIS)

2001-01-01

The United States Department of Energy (DOE) continually seeks safer and more cost-effective technologies for the decontamination and decommissioning (D and D) of nuclear facilities. The Deactivation and Decommissioning Focus Area (DDFA) of the DOE's Office of Science and Technology sponsors large-scale demonstration and deployment projects (LSDDPs) to identify and demonstrate technologies that will be safer and more cost-effective. At these LSDDPs, developers and vendors of improved or innovative technologies showcase products that are potentially beneficial to the DOE's projects as well as others in the D and D community. Benefits sought include decreased health and safety risks to personnel and the environment, increased productivity, and decreased cost of operation. The Idaho National Engineering and Environmental Laboratory (INEEL) LSDDP generated a list of need statements defining specific needs or problems where improved technologies could be incorporated into ongoing D and D tasks. Advances in characterization technologies are continuously being sought to decrease the cost of sampling and increase the speed of obtaining results. Currently it can take as long as 90 days to receive isotopic analysis of radioactive samples from laboratories on soil, liquid, and paint samples. The cost to analyze these types of samples for radionuclides is about $150 per sample. This demonstration investigated the feasibility of using the Surveillance and Measurement System (SAMS) (innovative technology) to make in situ isotopic radiation measurements in paint and soil. Sample collection and on-site laboratory analysis (baseline technology) is currently being used on D and D sampling activities. Benefits expected from using the innovative technology include: Significant decrease in time to receive results on radiological samples; Decrease in cost associated with sample collection, preparation, analysis, and disposal; Equivalent data quality to laboratory analysis; and Fewer

Decontamination of paint-coated concrete in nuclear plants using laser technology

Energy Technology Data Exchange (ETDEWEB)

Anthofer, Anton; Lippmann, Wolfgang; Hurtado, Antonio [Technische Univ. Dresden (Germany). Chair of Hydrogen and Nuclear Technology

2013-07-01

A review of the state of the art shows the technical novelty of the combined project. The development of an all-in-one process for treatment hazard chemical contamination on concrete structures with online monitoring method reduces the laborious mechanic decontamination and post-treatment. For safe experimental investigations, a three-barrier-system was constructed and can be used for tests with - first - epoxy paint in order to analyze and optimize the process. Simulation models help to formulate a mathematic scheme of the decontamination process by laser technology. The goal is a decontamination system with an online analyzing system of the flue gas for a mobile and extensive component in nuclear and conventional decommission. (orig.)

Cold Atmospheric Plasma Technology for Decontamination of Space Equipment

Science.gov (United States)

Thomas, Hubertus; Rettberg, Petra; Shimizu, Tetsuji; Thoma, Markus; Morfill, Gregor; Zimmermann, Julia; Müller, Meike; Semenov, Igor

2016-07-01

Cold atmospheric plasma (CAP) technology is very fast and effective in inactivation of all kinds of pathogens. It is used in hygiene and especially in medicine, since the plasma treatment can be applied to sensitive surfaces, like skin, too. In a first study to use CAP for the decontamination of space equipment we could show its potential as a quite promising alternative to the standard "dry heat" and H2O2 methods [Shimizu et al. Planetary and Space Science, 90, 60-71. (2014)]. In a follow-on study we continue the investigations to reach high application level of the technology. First, we redesign the actual setup to a plasma-gas circulation system, increasing the effectivity of inactivation and the sustainability. Additionally, we want to learn more about the plasma chemistry processes involved in the inactivation. Therefore, we perform detailed plasma and gas measurements and compare them to numerical simulations. The latter will finally be used to scale the decontamination system to sizes useful also for larger space equipment. Typical materials relevant for space equipment will be tested and investigated on surface material changes due to the plasma treatment. Additionally, it is planned to use electronic boards and compare their functionality before and after the CAP expose. We will give an overview on the status of the plasma decontamination project funded by the Bavarian Ministry of Economics.

Branching innovation, recombinant innovation, and endogenous technological transitions

NARCIS (Netherlands)

Frenken, K.; Izquierdo, L.; Zeppini, P.

2012-01-01

We propose a model of technological transitions based on two different types of innovations. Branching innovations refer to technological improvements along a particular path, while recombinant innovations represent fusions of multiple paths. Recombinant innovations create "short-cuts" which reduce

New technologies for PCB [polychlorinated biphenyl] decontamination

International Nuclear Information System (INIS)

Webber, I.

1993-01-01

Polychlorinated biphenyls (PCB) were mixed with chlorobenzenes to reduce viscosity and provide for both electrical insulation and convective heat transfers. These mixtures were known as askarels, and ca 99.8% of PCBs used in electrical applications are contained in askarel-filled transformers and capacitors. It is estimated that there are ca 180 million gal of PCB-contaminated oil distributed through over 3 million transformers in the USA. Technology used for decontaminating these transformers depends on the concentration of the PCB contamination. At low PCB concentrations of up to ca 2,000 ppM, chemical methods can be used; at higher concentrations, alternative disposal options become more attractive. For chemical treatment, a small mobile unit using quick-reacting reagents has been developed for on-site decontamination. For highly contaminated transformers, retrofilling is very attractive since the owner's liability is minimized at minimum cost. Conventional flush/drain procedures have such drawbacks as the inability to remove oil trapped in windings and the leaching of trapped PCBs back into the uncontaminated retrofill oil over time. A new process has been developed to solve the leaching problem and to decontaminate the drained askarel at room temperature using a catalyst. An alternative disposal strategy involves dismantling the transformer carcass, incinerating non-recyclable materials, and cleaning the metals and wire with solvent. 8 figs

Metal decontamination for waste minimization using liquid metal refining technology

International Nuclear Information System (INIS)

Joyce, E.L. Jr.; Lally, B.; Ozturk, B.; Fruehan, R.J.

1993-01-01

The current Department of Energy Mixed Waste Treatment Project flowsheet indicates that no conventional technology, other than surface decontamination, exists for metal processing. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain concentration. This project is in support of the National Mixed Low Level Waste Treatment Program. Because of the high cost of disposal, it is important to develop an effective decontamination and volume reduction method for low-level contaminated metals. It is important to be able to decontaminate complex shapes where surfaces are hidden or inaccessible to surface decontamination processes and destruction of organic contamination. These goals can be achieved by adapting commercial metal refining processes to handle radioactive and organic contaminated metal. The radioactive components are concentrated in the slag, which is subsequently vitrified; hazardous organics are destroyed by the intense heat of the bath. The metal, after having been melted and purified, could be recycled for use within the DOE complex. In this project, we evaluated current state-of-the-art technologies for metal refining, with special reference to the removal of radioactive contaminants and the destruction of hazardous organics. This evaluation was based on literature reports, industrial experience, plant visits, thermodynamic calculations, and engineering aspects of the various processes. The key issues addressed included radioactive partitioning between the metal and slag phases, minimization of secondary wastes, operability of the process subject to widely varying feed chemistry, and the ability to seal the candidate process to prevent the release of hazardous species

Available decontamination and decommissioning capabilities at the Savannah River Technology Center

International Nuclear Information System (INIS)

Polizzi, L.M.; Norkus, J.K.; Paik, I.K.; Wooten, L.A.

1992-01-01

The Safety Analysis and Engineering Services Group has performed a survey of the Savannah River Technology Center (SRTC) technical capabilities, skills, and experience in Decontamination and Decommissioning (D ampersand D) activities. The goal of this survey is to enhance the integration of the SRTC capabilities with the technical needs of the Environmental Restoration Department D ampersand D program and the DOE Office of Technology Development through the Integrated Demonstration Program. This survey has identified technical capabilities, skills, and experience in the following D ampersand D areas: Characterization, Decontamination, Dismantlement, Material Disposal, Remote Systems, and support on Safety Technology for D ampersand D. This review demonstrates the depth and wealth of technical capability resident in the SRTC in relation to these activities, and the unique qualifications of the SRTC to supply technical support in the area of DOE facility D ampersand D. Additional details on specific technologies and applications to D ampersand D will be made available on request

Technology Innovation

Science.gov (United States)

EPA produces innovative technologies and facilitates their creation in line with the Agency mission to create products such as the stormwater calculator, remote sensing, innovation clusters, and low-cost air sensors.

Group Innovation Ability of Agricultural Technological Innovation Strategic Alliance

Institute of Scientific and Technical Information of China (English)

Chishun; MA; Jintian; YU

2013-01-01

Agricultural technological innovation strategic alliance, as an important form of strategic alliance, has steadily strengthened the collaborative management among organizations and raised competitive power with the backing of improved group innovation ability. This article studies innovation ability from individual innovation ability to the group innovation ability. Firstly, basic connotation of group innovation ability is to be concluded through the comparison of individual and group innovation ability. Secondly, evaluation index system is to be established based on the influencing factors of the group innovation ability of agricultural technological innovation strategic alliance and evaluation is based on three dimensions, namely organization technological innovation ability, alliance collaborative innovation ability as well as innovation environment. Furthermore, basic methods for promoting the group innovation ability of alliance are to be proposed.

Heat stress monitoring system. Innovative technology summary report

International Nuclear Information System (INIS)

1998-11-01

The US Department of Energy's (DOE) nuclear facility decontamination and decommissioning (D and D) program involves the need to decontaminate and decommission buildings expeditiously and cost-effectively. Simultaneously, the health and safety of personnel involved in the D and D activities is of primary concern. Often, D and D workers must perform duties in inclement weather, and because they also frequently work in contaminated areas, they must wear personal protective clothing and/or respirators. Monitoring the health status of workers under these conditions is an important component of ensuring their safety. The MiniMitter VitalSense Telemetry System's heat stress monitoring system (HSMS) is designed to monitor the vital signs of individual workers as they perform work in conditions that might be conducive to heat exhaustion or heat stress. The HSMS provides real-time data on the physiological condition of workers which can be monitored to prevent heat stress or other adverse health situations. This system is particularly useful when workers are wearing personal protective clothing or respirators that make visual observation of their condition more difficult. The MiniMitter VitalSense Telemetry System can monitor up to four channels (e.g., heart rate, body activity, ear canal, and skin temperature) and ten workers from a single supervisory station. The monitors are interfaced with a portable computer that updates and records information on individual workers. This innovative technology, even though it costs more, is an attractive alternative to the traditional (baseline) technology, which measures environmental statistics and predicts the average worker's reaction to those environmental conditions without taking the physical condition of the individual worker into consideration. Although use of the improved technology might be justified purely on the basis of improved safety, it has the potential to pay for itself by reducing worker time lost caused by heat

Anthrax Sampling and Decontamination: Technology Trade-Offs

Energy Technology Data Exchange (ETDEWEB)

Price, Phillip N.; Hamachi, Kristina; McWilliams, Jennifer; Sohn, Michael D.

2008-09-12

The goal of this project was to answer the following questions concerning response to a future anthrax release (or suspected release) in a building: 1. Based on past experience, what rules of thumb can be determined concerning: (a) the amount of sampling that may be needed to determine the extent of contamination within a given building; (b) what portions of a building should be sampled; (c) the cost per square foot to decontaminate a given type of building using a given method; (d) the time required to prepare for, and perform, decontamination; (e) the effectiveness of a given decontamination method in a given type of building? 2. Based on past experience, what resources will be spent on evaluating the extent of contamination, performing decontamination, and assessing the effectiveness of the decontamination in abuilding of a given type and size? 3. What are the trade-offs between cost, time, and effectiveness for the various sampling plans, sampling methods, and decontamination methods that have been used in the past?

105-C Reactor interim safe storage project technology integration plan

International Nuclear Information System (INIS)

Pulsford, S.K.

1997-01-01

The 105-C Reactor Interim Safe Storage Project Technology Integration Plan involves the decontamination, dismantlement, and interim safe storage of a surplus production reactor. A major goal is to identify and demonstrate new and innovative D and D technologies that will reduce costs, shorten schedules, enhance safety, and have the potential for general use across the RL complex. Innovative technologies are to be demonstrated in the following areas: Characterization; Decontamination; Waste Disposition; Dismantlement, Segmentation, and Demolition; Facility Stabilization; and Health and Safety. The evaluation and ranking of innovative technologies has been completed. Demonstrations will be selected from the ranked technologies according to priority. The contractor team members will review and evaluate the demonstration performances and make final recommendations to DOE

Field Evaluation of Whole Airliner Decontamination Technologies - Wide-Body Aircraft With Dual-Use Application for Railcars

National Research Council Canada - National Science Library

Gale, William F; Gale, Hyacinth S; Watson, Jean

2008-01-01

... vaporized hydrogen peroxide (VHP )* is discussed. The report is submitted in the context of a decontamination technology selection exercise, laboratory work conducted on the efficacy of thermal decontamination, and as a follow-on to a...

Large-bore pipe decontamination

International Nuclear Information System (INIS)

Ebadian, M.A.

1998-01-01

The decontamination and decommissioning (D and D) of 1200 buildings within the US Department of Energy-Office of Environmental Management (DOE-EM) Complex will require the disposition of miles of pipe. The disposition of large-bore pipe, in particular, presents difficulties in the area of decontamination and characterization. The pipe is potentially contaminated internally as well as externally. This situation requires a system capable of decontaminating and characterizing both the inside and outside of the pipe. Current decontamination and characterization systems are not designed for application to this geometry, making the direct disposal of piping systems necessary in many cases. The pipe often creates voids in the disposal cell, which requires the pipe to be cut in half or filled with a grout material. These methods are labor intensive and costly to perform on large volumes of pipe. Direct disposal does not take advantage of recycling, which could provide monetary dividends. To facilitate the decontamination and characterization of large-bore piping and thereby reduce the volume of piping required for disposal, a detailed analysis will be conducted to document the pipe remediation problem set; determine potential technologies to solve this remediation problem set; design and laboratory test potential decontamination and characterization technologies; fabricate a prototype system; provide a cost-benefit analysis of the proposed system; and transfer the technology to industry. This report summarizes the activities performed during fiscal year 1997 and describes the planned activities for fiscal year 1998. Accomplishments for FY97 include the development of the applicable and relevant and appropriate regulations, the screening of decontamination and characterization technologies, and the selection and initial design of the decontamination system

Advanced technologies for decontamination and conversion of scrap metal

International Nuclear Information System (INIS)

MacNair, V.; Muth, T.; Shasteen, K.; Liby, A.; Hradil, G.; Mishra, B.

1996-01-01

In October 1993, Manufacturing Sciences Corporation was awarded DOE contract DE-AC21-93MC30170 to develop and test recycling of radioactive scrap metal (RSM) to high value and intermediate and final product forms. This work was conducted to help solve the problems associated with decontamination and reuse of the diffusion plant barrier nickel and other radioactively contaminated scrap metals present in the diffusion plants. Options available for disposition of the nickel include decontamination and subsequent release or recycled product manufacture for restricted end use. Both of these options are evaluated during the course of this research effort. work during phase I of this project successfully demonstrated the ability to make stainless steel from barrier nickel feed. This paved the way for restricted end use products made from stainless steel. Also, after repeated trials and studies, the inducto-slag nickel decontamination process was eliminated as a suitable alternative. Electro-refining appeared to be a promising technology for decontamination of the diffusion plant barrier material. Goals for phase II included conducting experiments to facilitate the development of an electro-refining process to separate technetium from nickel. In parallel with those activities, phase II efforts were to include the development of the necessary processes to make useful products from radioactive scrap metal. Nickel from the diffusion plants as well as stainless steel and carbon steel could be used as feed material for these products

TRU-waste decontamination and size reduction review, June 1983, US DOE/PNC technology exchange

International Nuclear Information System (INIS)

Becker, G.W. Jr.

1983-01-01

A review of transuranic (TRU) noncombustible waste decontamination and size reduction technology is presented. Electropolishing, vibratory cleaning, and spray decontamination processes developed at Battelle Pacific Northwest Laboratory (PNL) and Savannah River Laboratory (SRL) are highlighted. TRU waste size reduction processes at (PNL), Los Alamos National Laboratory (LANL), the Rocky Flats Plant (RFP), and SRL are also highlighted

Cutting-edge characterization technologies for D and D

International Nuclear Information System (INIS)

Bossart, S.J.; Kasper, K.M.

1998-01-01

The US Department of Energy's (DOE's) Office of Science and Technology (OST) has been developing and demonstrating technologies to improve methods used to characterize the presence and quantity of contaminants. As a part of OST, the Deactivation and Decommissioning (D and D) Focus Area has been developing and demonstrating innovative technologies for facility characterization to reduce costs associated with this important D and D activity. Characterization activities are an essential and substantial part of D and D. An initial scoping survey must be done to identify personnel hazards and to develop a decommissioning plan. Detailed characterization data must be collected to determine the type and magnitude of contaminants to begin decontamination and dismantlement activities. Surveys must be done during decontamination activities to determine the effectiveness of the decontamination efforts. A final status survey is required, and a confirmatory survey may also be required to document the end-state of a facility. These extensive characterization efforts contribute substantially to the overall cost of a D and D project. Through its Large-Scale Demonstration Program, the D and D Focus Area has been demonstrating many innovative technologies to improve D and D characterization processes. During the large-scale demonstration projects, innovative characterization technologies are evaluated alongside competing baseline technologies. Innovative technology summary reports are being generated on all of these technologies. When they are completed, they will be available through the DOE Office of Science and Technology's Homepage at http://em-52.em.doe.gov/idf/ost/pubs.htm

Strategy of technology and innovation

International Nuclear Information System (INIS)

Kim, Yeon Min

1998-10-01

This book introduces strategy of technology and innovation which includes design and development of strategy of technology, performance of strategy of technology and building and practice of strategy of development. The contents of this book are form of industrial innovation, act in strategy, advantage of technical innovation, new perspective of studying and innovation, alliance with competitor, cost of transmission and innovation, learning cycle of new product and power of consistency of product.

A state of the art report on the decontamination technology for dry ice blasting

International Nuclear Information System (INIS)

Shin, J. M.; Kim, K. H.; Park, J. J.; Lee, H. H.; Yang, M. S.; Nam, S. H.; Kim, M. J.

2000-05-01

DUPIC fuel fabrication process is a dry processing technology to manufacture CANDU compatible fuel through a direct reprocessing fabrication process from spent PWR fuel. DUPIC fuel fabrication process consists of the slitting of the spent PWR fuel rods, OREOX processing, homogeneous mixing, pelletizing and sintering. All these processes should be conducted by remote means in a M6 hot cell at IMEF. Since DUPIC fuel fabrication process includes powder handling process of highly radioactive spent fuel, decontamination of highly radioactive particulates from all types of surfaces such as DUPIC fuel manufacturing equipment, hot cell floor, tools is very important to improve the safety of hot cell and reduce the dose exposure to operator, This report describes various technologies for dry ice blasting. It provides the fundamentals of dry ice blasting decontamination and technical review of dry ice blasting on the radioactive decontamination

A state of the art report on the decontamination technology for dry ice blasting

Energy Technology Data Exchange (ETDEWEB)

Shin, J M; Kim, K H; Park, J J; Lee, H H; Yang, M S; Nam, S H; Kim, M J

2000-05-01

DUPIC fuel fabrication process is a dry processing technology to manufacture CANDU compatible fuel through a direct reprocessing fabrication process from spent PWR fuel. DUPIC fuel fabrication process consists of the slitting of the spent PWR fuel rods, OREOX processing, homogeneous mixing, pelletizing and sintering. All these processes should be conducted by remote means in a M6 hot cell at IMEF. Since DUPIC fuel fabrication process includes powder handling process of highly radioactive spent fuel, decontamination of highly radioactive particulates from all types of surfaces such as DUPIC fuel manufacturing equipment, hot cell floor, tools is very important to improve the safety of hot cell and reduce the dose exposure to operator, This report describes various technologies for dry ice blasting. It provides the fundamentals of dry ice blasting decontamination and technical review of dry ice blasting on the radioactive decontamination.

Technology development for nuclear fuel cycle waste treatment - Decontamination, decommissioning and environmental restoration (1)

International Nuclear Information System (INIS)

Lee, Byung Jik; Won, Hui Jun; Yoon, Ji Sup and others

1997-12-01

Through the project of D econtamination, decommissioning and environmental restoration technology development , the following were studied. 1. Development of decontamination and repair technology for nuclear fuel cycle facilities 2. Development of dismantling technology 3. Environmental remediation technology development. (author). 95 refs., 45 tabs., 163 figs

Pipe Explorer surveying system. Innovative technology summary report

International Nuclear Information System (INIS)

1999-06-01

The US Department of Energy's (DOE) Chicago Operations Office and the DOE's Federal Energy Technology Center (FETC) developed a Large Scale Demonstration Project (LSDP) at the Chicago Pile-5 Research Reactor (CP-5) at Argonne National Laboratory-East (ANL). The objective of the LSDP is to demonstrate potentially beneficial decontamination and decommissioning (D and D) technologies in comparison with current baseline technologies. The Pipe Explorer trademark system was developed by Science and Engineering Associates, Inc. (SEA), Albuquerque, NM as a deployment method for transporting a variety of survey tools into pipes and ducts. Tools available for use with the system include alpha, beta and gamma radiation detectors; video cameras; and pipe locator beacons. Different versions of this technology have been demonstrated at three other sites; results of these demonstrations are provided in an earlier Innovative Technology Summary Report. As part of a D and D project, characterization radiological contamination inside piping systems is necessary before pipes can be recycled, remediated or disposed. This is usually done manually by surveying over the outside of the piping only, with limited effectiveness and risk of worker exposure. The pipe must be accessible to workers, and embedded pipes in concrete or in the ground would have to be excavated at high cost and risk of exposure to workers. The advantage of the Pipe Explorer is its ability to perform in-situ characterization of pipe internals

Decontamination of soils and materials containing medium-fired PuO{sub 2} using inhibited fluorides with polymer filtration technology

Energy Technology Data Exchange (ETDEWEB)

Temer, D.J.; Villarreal, R.; Smith, B.F. [Los Alamos National Lab., NM (United States)

1997-10-01

The decontamination of soils and/or materials from medium-fired plutonium oxide (PuO{sub 2}) with an effective and efficient decontamination agent that will not significantly dissolve the matrix requires a new and innovative technology. After testing several decontamination agents and solutions for dissolution of medium-fired PuO{sub 2}, the most successful decontamination solutions were fluoride compounds, which were effective in breaking the Pu-oxide bond but would not extensively dissolve soil constituents and other materials. The fluoride compounds, tetra fluoboric acid (HBF{sub 4}) and hydrofluorosilicic acid (H{sub 2}F{sub 6}Si), were effective in dissolving medium-fired PuO{sub 2}, and did not seem to have the potential to dissolve the matrix. In both compounds, the fluoride atom is attached to a boron or silicon atom that inhibits the reactivity of the fluoride towards other compounds or materials containing atoms less attracted to the fluoride atom in an acid solution. Because of this inhibition of the reactivity of the fluoride ion, these compounds are termed inhibited fluoride compounds or agents. Both inhibited fluorides studied effectively dissolved medium-fired PuO{sub 2} but exhibited a tendency to not attack stainless steel or soil. The basis for selecting inhibited fluorides was confirmed during leaching tests of medium-fired PuO{sub 2} spiked into soil taken from the Idaho National Engineering Laboratory (INEL). When dissolved in dilute HNO{sub 3}, HCl, or HBr, both inhibited fluoride compounds were effective at solubilizing the medium-fired PuO{sub 2} from spiked INEL soil.

Contaminated concrete: Occurrence and emerging technologies for DOE decontamination

International Nuclear Information System (INIS)

Dickerson, K.S.; Wilson-Nichols, M.J.; Morris, M.I.

1995-08-01

The goals of the Facility Deactivation, Decommissioning, and Material Disposition Focus Area, sponsored by the US Department of Energy (DOE) Office of Technology Development, are to select, demonstrate, test, and evaluate an integrated set of technologies tailored to provide a complete solution to specific problems posed by deactivation, decontamination, and decommissioning, (D ampersand D). In response to these goals, technical task plan (TTP) OR152002, entitled Accelerated Testing of Concrete Decontamination Methods, was submitted by Oak Ridge National Laboratory. This report describes the results from the initial project tasks, which focused on the nature and extent of contaminated concrete, emerging candidate technologies, and matching of emerging technologies to concrete problems. Existing information was used to describe the nature and extent of contamination (technology logic diagrams, data bases, and the open literature). To supplement this information, personnel at various DOE sites were interviewed, providing a broad perspective of concrete contamination. Because characterization is in the initial stage at many sites, complete information is not available. Assimilation of available information into one location is helpful in identifying potential areas of concern in the future. The most frequently occurring radiological contaminants within the DOE complex are 137 Cs, 238 U (and it daughters), and 60 Co, followed closely by 90 Sr and tritium, which account for -30% of the total occurrence. Twenty-four percent of the contaminants were listed as unknown, indicating a lack of characterization information, and 24% were listed as other contaminants (over 100 isotopes) with less than 1% occurrence per isotope

Contaminated concrete: Occurrence and emerging technologies for DOE decontamination

Energy Technology Data Exchange (ETDEWEB)

Dickerson, K.S.; Wilson-Nichols, M.J. [Oak Ridge National Lab., Grand Junction, CO (United States); Morris, M.I. [Oak Ridge National Lab., TN (United States)

1995-08-01

The goals of the Facility Deactivation, Decommissioning, and Material Disposition Focus Area, sponsored by the US Department of Energy (DOE) Office of Technology Development, are to select, demonstrate, test, and evaluate an integrated set of technologies tailored to provide a complete solution to specific problems posed by deactivation, decontamination, and decommissioning, (D&D). In response to these goals, technical task plan (TTP) OR152002, entitled Accelerated Testing of Concrete Decontamination Methods, was submitted by Oak Ridge National Laboratory. This report describes the results from the initial project tasks, which focused on the nature and extent of contaminated concrete, emerging candidate technologies, and matching of emerging technologies to concrete problems. Existing information was used to describe the nature and extent of contamination (technology logic diagrams, data bases, and the open literature). To supplement this information, personnel at various DOE sites were interviewed, providing a broad perspective of concrete contamination. Because characterization is in the initial stage at many sites, complete information is not available. Assimilation of available information into one location is helpful in identifying potential areas of concern in the future. The most frequently occurring radiological contaminants within the DOE complex are {sup 137}Cs, {sup 238}U (and it daughters), and {sup 60}Co, followed closely by {sup 90}Sr and tritium, which account for {minus}30% of the total occurrence. Twenty-four percent of the contaminants were listed as unknown, indicating a lack of characterization information, and 24% were listed as other contaminants (over 100 isotopes) with less than 1% occurrence per isotope.

Preliminary design and estimate of capital and operating costs for a production scale application of laser decontamination technology

International Nuclear Information System (INIS)

Pang, Ho-ming; Edelson, M.C.

1994-01-01

The application of laser ablation technology to the decontamination of radioactive metals, particularly the surfaces of equipment, is discussed. Included is information related to the design, capital and operating costs, and effectiveness of laser ablation technology, based on commercial excimer and Nd:YAG lasers, for the decontamination of production scale equipment

National Strategies for Technological Innovation

Science.gov (United States)

Rossini, Frederick; Bozeman, Barry

1977-01-01

Considers the implications of the technological innovation literature for possible national strategies for innovation. Sketches highly generalized innovation strategies for nations at various levels of technological development. (Author/IRT)

The state of the art on the dry decontamination technologies applicable to highly radioactive contaminants and their needs for the national nuclear fuel cycle developent

International Nuclear Information System (INIS)

Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. H.; Chol, W. K.; Kim, G. N.; Moon, J. K.

2000-12-01

This report is intended to establish their needs to support the dry decontamination activities applicable to highly radioactive contaminants based on the requirement of technologies development suggested from the national nuclear fuel cycle projects, such as DUPIC, advanced spent fuel management and long-lived radionuclides conversion. The technology needs associated with decontamination addressed the requirements associated with the efficiency of decontamination technology, the reduction of secondary wastes, applicabilities and the remote operation. And also, Characterization and decontamination technologies for various contaminants are reviewed and analysed. Based on the assessment, Unit dry decontamination processes are selected and the schematic flow diagram for decontamination of highly radioactive contaminants

The state of the art on the dry decontamination technologies applicable to highly radioactive contaminants and their needs for the national nuclear fuel cycle developent

Energy Technology Data Exchange (ETDEWEB)

Oh, Won Zin; Lee, K.W.; Won, H.J.; Jung, C.H.; Chol, W.K.; Kim, G.N.; Moon, J.K

2000-12-01

This report is intended to establish their needs to support the dry decontamination activities applicable to highly radioactive contaminants based on the requirement of technologies development suggested from the national nuclear fuel cycle projects, such as DUPIC, advanced spent fuel management and long-lived radionuclides conversion. The technology needs associated with decontamination addressed the requirements associated with the efficiency of decontamination technology, the reduction of secondary wastes, applicabilities and the remote operation. And also, Characterization and decontamination technologies for various contaminants are reviewed and analysed. Based on the assessment, Unit dry decontamination processes are selected and the schematic flow diagram for decontamination of highly radioactive contaminants.

The Management of Innovation and Technology

DEFF Research Database (Denmark)

Howells, John

in innovation - The reciprocal relationship between intellectual property law and technological innovation. - The role of technological skills and regimes of technological education in innovation. - An introduction to the role of the state in maintaining the innovative capacity of the private sector....... of the reality of taking decisions on innovation. The chapters cover: - The social context for individual acts of creative insight - The development of the technology-market relationship - The management of R&D and technological standards - Technological competition - The role of institutions of finance...

A study on implementation plan of decontamination and decommissioning R and D and evaluation of KAERI soil decontamination process

International Nuclear Information System (INIS)

Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. H.; Choi, W. K.; Kim, G. N.

2001-08-01

A. Decontamination Technology Development of Uranium Conversion Facility. Understanding of uranium conversion facility and related decontamination technologies, and analysis of current status of decontamination technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion of the erformance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility B. Treatment Technology Development of Uranium Sludge Analysis of the domestic and overseas research development status. Suggestion of treatment methodology of uranium slurry and cooperative R and D among industries, universities and research institute. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility C. Decommissioning Technology Development Analysis of the domestic and overseas research development status and the overview of decommissioning technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of TRIGA decommissioning D. Evaluation of KAERI Soil Decontamination Technology. Evaluation of soil decontamination process and the liquid decontamination waste treatment technology. Performance of soil decontamination test using solvent flushing test equipment for evaluation of residual radioactivity after decontami- nation and modeling of the results

A study on implementation plan of decontamination and decommissioning R and D and evaluation of KAERI soil decontamination process

Energy Technology Data Exchange (ETDEWEB)

Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. H.; Choi, W. K.; Kim, G. N

2001-08-01

A. Decontamination Technology Development of Uranium Conversion Facility. Understanding of uranium conversion facility and related decontamination technologies, and analysis of current status of decontamination technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion of the erformance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility B. Treatment Technology Development of Uranium Sludge Analysis of the domestic and overseas research development status. Suggestion of treatment methodology of uranium slurry and cooperative R and D among industries, universities and research institute. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility C. Decommissioning Technology Development Analysis of the domestic and overseas research development status and the overview of decommissioning technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of TRIGA decommissioning D. Evaluation of KAERI Soil Decontamination Technology. Evaluation of soil decontamination process and the liquid decontamination waste treatment technology. Performance of soil decontamination test using solvent flushing test equipment for evaluation of residual radioactivity after decontami- nation and modeling of the results.

Agricultural pathogen decontamination technology-reducing the threat of infectious agent spread.

Energy Technology Data Exchange (ETDEWEB)

Betty, Rita G.; Bieker, Jill Marie; Tucker, Mark David

2005-10-01

Outbreaks of infectious agricultural diseases, whether natural occurring or introduced intentionally, could have catastrophic impacts on the U.S. economy. Examples of such agricultural pathogens include foot and mouth disease (FMD), avian influenza (AI), citrus canker, wheat and soy rust, etc. Current approaches to mitigate the spread of agricultural pathogens include quarantine, development of vaccines for animal diseases, and development of pathogen resistant crop strains in the case of plant diseases. None of these approaches is rapid, and none address the potential persistence of the pathogen in the environment, which could lead to further spread of the agent and damage after quarantine is lifted. Pathogen spread in agricultural environments commonly occurs via transfer on agricultural equipment (transportation trailers, tractors, trucks, combines, etc.), having components made from a broad range of materials (galvanized and painted steel, rubber tires, glass and Plexiglas shields, etc), and under conditions of heavy organic load (mud, soil, feces, litter, etc). A key element of stemming the spread of an outbreak is to ensure complete inactivation of the pathogens in the agricultural environment and on the equipment used in those environments. Through the combination of enhanced agricultural pathogen decontamination chemistry and a validated inactivation verification methodology, important technologies for incorporation as components of a robust response capability will be enabled. Because of the potentially devastating economic impact that could result from the spread of infectious agricultural diseases, the proposed capability components will promote critical infrastructure protection and greater border and food supply security. We investigated and developed agricultural pathogen decontamination technologies to reduce the threat of infectious-agent spread, and thus enhance agricultural biosecurity. Specifically, enhanced detergency versions of the patented

Decontamination of process equipment using recyclable chelating solvent

International Nuclear Information System (INIS)

Jevec, J.; Lenore, C.; Ulbricht, S.

1995-01-01

The Department of Energy (DOE) is now faced with the task of meeting decontamination and decommissioning obligations at numerous facilities by the year 2019. Due to the tremendous volume of material involved, innovative decontamination technologies are being sought that can reduce the volumes of contaminated waste materials and secondary wastes requiring disposal. With sufficient decontamination, some of the material from DOE facilities could be released as scrap into the commercial sector for recycle, thereby reducing the volume of radioactive waste requiring disposal. Although recycling may initially prove to be more costly than current disposal practices, rapidly increasing disposal costs are expected to make recycling more and more cost effective. Additionally, recycling is now perceived as the ethical choice in a world where the consequences of replacing resources and throwing away reusable materials are impacting the well-being of the environment. Current approaches to the decontamination of metals most often involve one of four basic process types: (1) chemical, (2) manual and mechanical, (3) electrochemical, and (4) ultrasonic. open-quotes Hardclose quotes chemical decontamination solutions, capable of achieving decontamination factors (Df's) of 50 to 100, generally involve reagent concentrations in excess of 5%, tend to physically degrade the surface treated, and generate relatively large volumes of secondary waste. open-quotes Softclose quotes chemical decontamination solutions, capable of achieving Df's of 5 to 10, normally consist of reagents at concentrations of 0.1 to 1%, generally leave treated surfaces in a usable condition, and generate relatively low secondary waste volumes. Under contract to the Department of Energy, the Babcock ampersand Wilcox Company is developing a chemical decontamination process using chelating agents to remove uranium compounds and other actinide species from process equipment

Evaluation of Coating Removal and Aggressive Surface Removal Surface Technologies Applied to Concrete Walls, Brick Walls, and Concrete Ceilings

International Nuclear Information System (INIS)

Ebadian, M.A.; Lagos, L.E.

1997-01-01

The purpose of this investigation was to test and evaluate innovative and commercially available technologies for the surface decontamination of walls and ceilings. This investigation supports the DOE's objectives of reducing risks to human health and the environment through its restoration projects at FEMP and MEMP. This project was performed at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU), where one innovative and four commercially available decontamination technologies were evaluated under standard, non-nuclear testing conditions. The performance data generated by this project will assist DOE site managers in the selection of the safest, most efficient, and most cost-effective decontamination technologies to accomplish their remediation objectives

Decontamination and decommissioning techniques for research reactors

International Nuclear Information System (INIS)

Oh, Won Zin; Won, H. J.; Jung, C. H.; Choi, W. K.; Kim, G. N.; Lee, K. W.

2002-05-01

Evaluation of soil decontamination process and the liquid decontamination waste treatment technology are investigation of organic acid as a decontamination agent, investigation of the liquid waste purification process and identification of recycling the decontamination agents. Participation on IAEA CRP meeting are preparation of IAEA technical report on 'studies on decommissioning of TRIGA reactors and site restoration technologies' and exchange the research result, technology, experience and safety regulation of the research reactor D and D of USA, Great Britain, Canada, Belgium, Italy, India and so forth

Oak Ridge K-25 Site Technology Logic Diagram. Volume 3, Technology evaluation data sheets; Part A, Characterization, decontamination, dismantlement

Energy Technology Data Exchange (ETDEWEB)

Fellows, R.L. [ed.

1993-02-26

The Oak Ridge K-25 Technology Logic Diagram (TLD), a decision support tool for the K-25 Site, was developed to provide a planning document that relates environmental restoration and waste management problems at the Oak Ridge K-25 Site to potential technologies that can remediate these problems. The TLD technique identifies the research necessary to develop these technologies to a state that allows for technology transfer and application to waste management, remedial action, and decontamination and decommissioning activities. The TLD consists of four separate volumes-Vol. 1, Vol. 2, Vol. 3A, and Vol. 3B. Volume 1 provides introductory and overview information about the TLD. Volume 2 contains logic diagrams. Volume 3 has been divided into two separate volumes to facilitate handling and use. This report is part A of Volume 3 concerning characterization, decontamination, and dismantlement.

Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4. Volume 1: Technology evaluation

International Nuclear Information System (INIS)

1994-09-01

During World War 11, the Oak Ridge Y-12 Plant was built as part of the Manhattan Project to supply enriched uranium for weapons production. In 1945, Building 9201-4 (Alpha-4) was originally used to house a uranium isotope separation process based on electromagnetic separation technology. With the startup of the Oak Ridge K-25 Site gaseous diffusion plant In 1947, Alpha-4 was placed on standby. In 1953, the uranium enrichment process was removed, and installation of equipment for the Colex process began. The Colex process--which uses a mercury solvent and lithium hydroxide as the lithium feed material-was shut down in 1962 and drained of process materials. Residual Quantities of mercury and lithium hydroxide have remained in the process equipment. Alpha-4 contains more than one-half million ft 2 of floor area; 15,000 tons of process and electrical equipment; and 23,000 tons of insulation, mortar, brick, flooring, handrails, ducts, utilities, burnables, and sludge. Because much of this equipment and construction material is contaminated with elemental mercury, cleanup is necessary. The goal of the Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 is to provide a planning document that relates decontamination and decommissioning and waste management problems at the Alpha-4 building to the technologies that can be used to remediate these problems. The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 builds on the methodology transferred by the U.S. Air Force to the Environmental Management organization with DOE and draws from previous technology logic diagram-efforts: logic diagrams for Hanford, the K-25 Site, and ORNL

Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4. Volume 1: Technology evaluation

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

During World War 11, the Oak Ridge Y-12 Plant was built as part of the Manhattan Project to supply enriched uranium for weapons production. In 1945, Building 9201-4 (Alpha-4) was originally used to house a uranium isotope separation process based on electromagnetic separation technology. With the startup of the Oak Ridge K-25 Site gaseous diffusion plant In 1947, Alpha-4 was placed on standby. In 1953, the uranium enrichment process was removed, and installation of equipment for the Colex process began. The Colex process--which uses a mercury solvent and lithium hydroxide as the lithium feed material-was shut down in 1962 and drained of process materials. Residual Quantities of mercury and lithium hydroxide have remained in the process equipment. Alpha-4 contains more than one-half million ft{sup 2} of floor area; 15,000 tons of process and electrical equipment; and 23,000 tons of insulation, mortar, brick, flooring, handrails, ducts, utilities, burnables, and sludge. Because much of this equipment and construction material is contaminated with elemental mercury, cleanup is necessary. The goal of the Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 is to provide a planning document that relates decontamination and decommissioning and waste management problems at the Alpha-4 building to the technologies that can be used to remediate these problems. The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 builds on the methodology transferred by the U.S. Air Force to the Environmental Management organization with DOE and draws from previous technology logic diagram-efforts: logic diagrams for Hanford, the K-25 Site, and ORNL.

ASSESSMENT OF QUALITY OF INNOVATIVE TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Larisa Alexejevna Ismagilova

2016-12-01

Full Text Available We consider the topical issue of implementation of innovative technologies in the aircraft engine building industry. In this industry, products with high reliability requirements are developed and mass-produced. These products combine the latest achievements of science and technology. To make a decision on implementation of innovative technologies, a comprehensive assessment is carried out. It affects the efficiency of the innovations realization. In connection with this, the assessment of quality of innovative technologies is a key aspect in the selection of technological processes for their implementation. Problems concerning assessment of the quality of new technologies and processes of production are considered in the suggested method with respect to new positions. The developed method of assessing the quality of innovative technologies stands out for formed system of the qualimetric characteristics ensuring the effectiveness, efficiency, adaptability of innovative technologies and processes. The feature of suggested system of assessment is that it is based on principles of matching and grouping of quality indicators of innovative technologies and the characteristics of technological processes. The indicators are assessed from the standpoint of feasibility, technologies competiveness and commercial demand of products. In this paper, we discuss the example of implementing the approach of assessing the quality of the innovative technology of high-tech products such as turbine aircraft engine.

Global Positioning Radiometric Scanner System. Innovative Technology Summary Report

International Nuclear Information System (INIS)

2001-01-01

The US DOE continually seeks safer and more cost-effective technologies for use in decontamination and decommissioning (D and D) of nuclear facilities. To this end, the Deactivation and Decommissioning Focus Area (DDFA) of the DOE OST sponsors the Large Scale Demonstration and Deployment Projects (LSDDP). At these LSDDPs, developers and vendors of improved or innovative technologies showcase products that are potentially beneficial to the DOE projects and to others in the D and D community. Benefits sought include decreased health and safety risks to personnel and the environment, increased productivity, and decreased costs of operation. The Idaho National Engineering and Environmental Laboratory (INEEL) LSDDP generated a list of statements defining specific needs or problems where improved technology could be incorporated into ongoing D and D tasks. One of the stated needs was for developing technologies that would reduce costs and shorten DDOE/EM--0552DOE/EM--0552 and D schedules by providing radiological characterizations to meet the free-release criteria. The Global Positioning Radiometric Scanner (GPRS system shown in Figure 1) utilizes a detection system; a portable computer, a differential global positioning system (d-gps), and a four wheel drive vehicle. Once the survey data has been collected, a software program called GeoSofttrademark generates a graphical representation of the radiological contamination extent. Baseline technology involves gridding the area and hand surveying each grid. This demonstration investigated the associated costs and the required time to evaluate the radiological characterization data from the GPRS with respect to the baseline technology. The GPRS system performs in-situ, real-time analyses to identify the extent of radiological contamination. Benefits expected from using the new innovative technology (GPRS) include: Reduced labor hours associated with performing the survey; Increased number of survey data points; Reduced

Innovative Technology Summary Report (ITSR)

International Nuclear Information System (INIS)

1999-01-01

This section summarizes the demonstration of an Infrared-based Non-Intrusive Liquid Level Detection Technology (NLLDT) at the 221-U Facility located within the Hanford site. This demonstration was conducted by Infrared, Inc. of Reno Nevada in conjunction with Bechtel Hanford Inc. (Environmental Restoration Contractor) and DOE Engineers. The Infrared Imaging System demonstrated by Infrared, Inc. provides an attractive alternative to the baseline technology which employs mechanical methods of opening vessels to detect liquid level. An Infrared Imaging Systems is able to exploit the variations in physical properties of tanks, vessels and piping systems and the enclosed liquid and air to produce clearly defined locations of liquids, if they exist. For decontamination and commissioning (D and D) projects, the use of the NLLDT System to detect liquids in vessels eliminates the need to physically open and inspect these vessels. Risks to workers associated with gaining access to these type objects and the possible exposure to radioactive or contaminated materials can nearly be eliminated. This demonstration was conducted with the goal of characterizing a number of target vessels located on the deck of the 221 U Facility. This technology is suitable for DOE nuclear facilities D and D sites or similar public or commercial sites that must be decontaminated

Technological literacy and innovation education

DEFF Research Database (Denmark)

Hansbøl, Mikala

Lately, in Denmark and internationally, there has been an increased focus on welfare technology and innovation. The Danish healthcare system is being fundamentally restructured and re-formed, the health professions are dealing with increased speed on the introductions of new political strategies...... on innovation education and educational activities fostering technological literacy. While focus on technological literacy has often (historically) taken a functionalist direction, and mainly been related to ICT and development of non- vocational curricula, more recent developments of approaches...... to technological literacy emphasizes profession oriented relational technological literacy. Furthermore, new definitions of 21st century competencies and skills emphasize creative learning and innovation skills and competencies as central ingredients in the 21st century labor market, and call for innovation...

Evaluation of Coating Removal and Aggressive Surface Removal Surface Technologies Applied to Concrete Walls, Brick Walls, and Concrete Ceilings

Energy Technology Data Exchange (ETDEWEB)

Lagos, L.E.; Ebadian, M.A.

1997-11-01

The purpose of this investigation was to test and evaluate innovative and commercially available technologies for the surface decontamination of walls and ceilings. This investigation supports the DOE's objectives of reducing risks to human health and the environment through its restoration projects at FEMP and MEMP. This project was performed at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU), where one innovative and four commercially available decontamination technologies were evaluated under standard, non-nuclear testing conditions. The performance data generated by this project will assist DOE site managers in the selection of the safest, most efficient, and most cost-effective decontamination technologies to accomplish their remediation objectives.

Reputation for technological innovation: Does it actually cohere with innovative activity?

Directory of Open Access Journals (Sweden)

Patrick J. Höflinger

2018-01-01

Full Text Available Firms strategically promote, foster and pursue a reputation for technological innovation. Yet, present research did not examine whether such perception actually coheres with innovative activity itself. Previous studies in this field often relied solely on tangible products/product introductions, hence we apply multiple proxies based on a firm's intangible innovative performance to examine the influences on reputation for technological innovation. Using patent, financial and consumer data our Poisson regression analyzes 65 international firms which have been nominated by 231 consumers. We apply time-series and likewise cross-sectional data for our interdisciplinary analysis. Our findings demonstrate that innovative performance (citation intensity is linked to reputation for technological innovation. Counter-intuitively, our results provide evidence that marketing intensity negatively influences a reputation for technological innovation. From the results, we conclude that innovative performance may be associated with a reputation for technological innovation. Actual technological advancement attracts attention from consumers that cannot be purchased with greater marketing investments. This implies that consumers appreciate the costly and uncertain R&D efforts and value those firms that constantly offer innovation. As a theoretical implication, the consideration of intangible inputs for reputation research is an important contribution for a holistic understanding. The results represent essential strategic information for innovation and marketing functions, where both divisions need to align their activities and investments.

Technological Innovation for China’s Logistics Industry

Directory of Open Access Journals (Sweden)

Chieh-Yu Lin

2008-01-01

Full Text Available China’s logistics industry has started to pay attention to adopt more efficient logistics technologies to provide better services for their customers. This paper employes the questionnaire survey to study the factors influencing the adoption of technological innovations by logistics service providers in China as well as the influences of technological innovation on supply chain performance. Technological innovations are categorized into data acquisition technologies, information technologies, warehousing technologies, and transportation technologies. The results show that the adoption of technological innovations is significantly influenced by technological, organizational and environmental factors, and adopting innovative technologies will increase supply chain performance for the logistics industry in China.

Development of decommissioning, decontamination and reuse technology for nuclear facilities

International Nuclear Information System (INIS)

Lee, K. W.; Moon, J. K.; Choi, B. S.

2012-03-01

In this project, the foundation of decommissioning technology through the development of core technologies applied to maintenance and decommissioning of nuclear facility was established. First of all, we developed the key technology such as safety assessment technology for decommissioning work needed at the preparatory stage of decommissioning of the highly contaminated facilities and simultaneous measurement technology of the high-level alpha/beta contamination applicable to the operation and decommissioning of the nuclear facilities. Second, we developed a remotely controlled laser ablation decontamination system which is useful for a removal of fixed contaminants and developed a chemical gel decontamination technology for a removal of non-fixed contaminants during the maintenance and decommissioning works of high radiation hot cells which have been used for a recycling or treatment of spent fuels. Third, we developed a volume reduction and self-disposal technology for dismantled concrete wastes. Also, the technology for volume reduction and stabilization of the peculiar wastes(HEPA filter and organic mixed wastes), which have been known to be very difficult to treat and manage, generated from the high radioactive facilities in operation, improvement and repair and under decommissioning was developed. Finally, this research project was developed a system for the reduction of radiotoxicity of several uranium mixtures generated in the front- and back-end nuclear fuel cycles with characteristics of highly enhanced proliferation-resistance and more environmental friendliness, which can make the uranium to be recovered or separated from the mixtures with a high purity level enough for the uranium to be reused and to be classified as C-class level for burial near the surface, and then which result in the much reduction in volume of the uranium mixture wastes

Recombinant innovation and endogenous technological transitions

NARCIS (Netherlands)

Frenken, K.; Izquierdo, L.R.; Zeppini, P.

2012-01-01

We propose a model of technological transitions based on two different types of innovations. Branching innovations refer to technological improvements along a particular path, while recombinant innovations represent fusions of multiple paths. Recombinant innovations create "short-cuts" which reduce

Cutting and decontamination technologies for nuclear facility dismantling; Technologien zur Zerlegung und zur Dekontamination von kerntechnischen Anlagen

Energy Technology Data Exchange (ETDEWEB)

Huebner, Felix; Grone, Georg von; Schultmann, Frank

2017-03-15

The German Government's decision to phase-out nuclear power will lead to a substantial increase of the number of nuclear decommissioning and dismantling projects. The decommissioning of nuclear facilities must meet the requirements of the radiation protection ordinance. This study deals with the decontamination and dismantling technologies available to meet radiation protection requirements. The aim of this study is to determine the state of the art in the field of decommissioning and dismantling technologies. Furthermore, future trends in the development and application of such technologies should be identified. A detailed study of current literature provides an overview of established decommissioning technologies. Moreover, experts were consulted in order to facilitate a practical assessment. The experts' statements indicate that (apart from the chemical decontamination of the primary circuit) the use of mechanical methods is generally preferred. Abrasive methods are rated as particularly efficient. According to the experts, the development of new decontamination technologies may allow a more efficient decontamination. However, the success of a new technology will be subject to its application costs. Mechanical technologies are preferred for the dismantling of nuclear facilities. The band saw has been identified as a standard tool in nuclear dismantling. The survey has concluded that there is no need for new dismantling technologies. The potential lies in the optimization of existing processes and techniques. With regard to remotely operated systems, experts' opinions vary on whether the use of these systems will increase in future. Most areas inside a nuclear facility have low radiation levels that allow the use of human labour for the dismantling. However, there is a need for an improvement in the allocation and management of decommissioning projects.

Game-like Technology Innovation Education

DEFF Research Database (Denmark)

Magnussen, Rikke

2011-01-01

  The aim of this paper is to discuss the first results and methodological challenges and perspectives of designing game-inspired scenarios for implementation of innovation processes into schools' science education. This paper comprises and report on a case study of a game-inspired innovation...... scenario designed for technology education in grades 7 - 9 in Danish schools. In the paper, methodological challenges of doing design-based research into technology innovation education are discussed. The preliminary results from the first studies of a game-inspired technology innovation camp are also...... presented, along with discussions of the future of development of these educational spaces....

Game-like Technology Innovation Education

DEFF Research Database (Denmark)

Magnussen, Rikke

2011-01-01

scenario designed for technology education in grades 7 - 9 in Danish schools. In the paper, methodological challenges of doing design-based research into technology innovation education are discussed. The preliminary results from the first studies of a game-inspired technology innovation camp are also...

Technology Development and Innovation | Wind | NREL

Science.gov (United States)

Technology Development and Innovation Technology Development and Innovation Technology Development Technology Center (NWTC) supports efforts to reduce bird and bat fatalities at wind energy projects and photo of wind turbines at the National Wind Technology Center. Wildlife technology research and

Art technologies as possible propulsars in technological innovation

DEFF Research Database (Denmark)

Jørgensen, Lars Botin

2003-01-01

kind. This discussion, of general character, constitutes the initial part of this paper. Then it briefly looks into the final terms of the papertitle and try to relate to the diffuse and discussed technological innovation. Both aspects – art and technology and technological innovation – will be dealt...... with from a historical/hermeneutic and social constructivist point of view, as the paper moves from a general principal level to a more specific, exemplary level, where three different art technologies are presented as possible propulsars in technological innovation.......Art and technology has, as the German philosopher Martin Heidegger points out, the same etymological root. A thorough investigation of the relationship between art and technology will show how this same root has manifested itself in different times and spaces bringing results of the most variegated...

Technology Matters - When new technology reshape innovation

DEFF Research Database (Denmark)

Edwards, Kasper; Pedersen, Jørgen Lindgaard

2004-01-01

Management of innovation is an important issue for firms and being good at this may be the deciding difference between death and survival. This paper ar-gues, based on 12 case studies, that new technology influence the innovative ca-pability of firms and disturbingly the process appears...... not to be managed in the sense that aims, instruments and resources are unclear. It is observed that new technology is adopted with a limited scope and fo-cus – often to solve a particular technical problem e.g. the quality of specifica-tion are too low. For a single reason a new technology is introduced within...... the firm, which over time becomes a source of innovation. However, through adoption of this new technology firms engage in a mu-tual learning and forming process where the firm learn by using the new technol-ogy. When learning, the firm and the new technology is mutually formed as the firm tries to adopt...

Stimulating technological innovation : problem identification and intervention formulation with the technological innovation systems framework

NARCIS (Netherlands)

Kieft, A.C.

2017-01-01

The technological innovation systems (TIS) framework provides a theory to understand under what conditions technological innovations are successfully developed and implemented. The objective of this dissertation is to further strengthen this TIS intervention framework, which is the part of the TIS

Developments in Decontamination Technologies of Military Personnel and Equipment

Science.gov (United States)

Sata, Utkarsh R.; Ramkumar, Seshadri S.

Individual protection is important for warfighters, first responders and civilians to meet the current threat of toxic chemicals and chemical warfare (CW) agents. Within the realm of individual protection, decontamination of warfare agents is not only required on the battlefield but also in laboratory, pilot plants, production and agent destruction sites. It is of high importance to evaluate various decontaminants and decontamination techniques for implementing the best practices in varying scenarios such as decontamination of personnel, sites and sensitive equipment.

Low-waste technology of prevention, decontamination and localization of radioactive contamination

International Nuclear Information System (INIS)

Kizhnerov, L. V.; Konstantinov, Ye. A.; Prokopenko, V. A.; Sorokin, N. M.

1997-01-01

The report presents the results of research in developing a low-waste technology of prevention, decontamination and localization of radioactive contamination founded on the of easily removed protective polymeric coating based on water and alcohol latexes and dispersion of polymers with special activating additives. The developed technology provides for the reduction of weakly fixed radioactive contamination of non-painted and painted surfaces to admissible levels (as a rule), it securely prevents and localizes contamination and does not generate secondary liquid radioactive wastes

Technology needs for decommissioning and decontamination

International Nuclear Information System (INIS)

Bundy, R.D.; Kennerly, J.M.

1993-12-01

This report summarizes the current view of the most important decontamination and decommissioning (D ampersand D) technology needs for the US Department of Energy facilities for which the D ampersand D programs are the responsibility of Martin Marietta Energy Systems, Inc. The source of information used in this assessment was a survey of the D ampersand D program managers at each facility. A summary of needs presented in earlier surveys of site needs in approximate priority order was supplied to each site as a starting point to stimulate thinking. This document reflects a brief initial assessment of ongoing needs; these needs will change as plans for D ampersand D are finalized, some of the technical problems are solved through successful development programs, and new ideas for D and D technologies appear. Thus, this assessment should be updated and upgraded periodically, perhaps, annually. This assessment differs from others that have been made in that it directly and solely reflects the perceived need for new technology by key personnel in the D ampersand D programs at the various facilities and does not attempt to consider the likelihood that these technologies can be successfully developed. Thus, this list of technology needs also does not consider the cost, time, and effort required to develop the desired technologies. An R ampersand D program must include studies that have a reasonable chance for success as well as those for which there is a high need. Other studies that considered the cost and probability of successful development as well as the need for new technology are documented. However, the need for new technology may be diluted in such studies; this document focuses only on the need for new technology as currently perceived by those actually charged with accomplishing D ampersand D

Innovative technology summary report: Innovative grouting and retrieval

International Nuclear Information System (INIS)

1998-10-01

Innovative grouting and retrieval (IGR) technology provides an innovative and cost-effective approach for full-pit and hot-spot retrieval of buried transuranic (TRU) waste sites and in situ disposal of buried waste with improved confinement. Innovative grouting technology: minimizes spreading of contamination by agglomerating the soil particles containing plutonium/americium particulates into nonaerosolizable particles; minimizes worker risks and exposure; is more effective in controlling the spread of contamination than common mining practices such as directed air flow, misting, and fixant sprays; eliminates further treatment because the grouted, rubberized waste is ready for shipment to the Waste Isolation Pilot Project (WIPP); reduces capital expenditures, operating costs, and containment structure requirements; and is an estimated five times faster than the baseline technology of removal, packaging, and storage

Innovate or imitate? Behavioural technological change

NARCIS (Netherlands)

Hommes, C.; Zeppini, P.

2013-01-01

We propose a behavioural model of technological change with evolutionary switching between boundedly rational costly innovators and free imitators, and study the endogenous interplay of innovation decisions, market price dynamics and technological progress. Innovation and imitation are strategic

Innovate or imitate? Behavioural technological change

NARCIS (Netherlands)

Hommes, C.; Zeppini, P.

2014-01-01

We propose a behavioural model of technological change with evolutionary switching between costly innovators and free imitators, and study the endogenous interplay of innovation decisions, market price dynamics and technological progress. Innovation and imitation are strategic substitutes and

Demonstration test on decontamination of contaminated pool water using liquid-solid settling technology with flocculants

International Nuclear Information System (INIS)

Aritomi, Masanori; Adachi, Toshihiro; Watanabe, Noriyuki; Tagawa, Akihiro; Hosobuchi, Shigeki; Takanashi, Junko

2013-01-01

For the purpose of supplying agricultural water, a stationary purification system for contaminated water had been developed on the basis of the liquid-solid settling technology using flocculants. Two kinds of flocculants had been developed on the basis of preliminary tests: one that compounds iron ferrocyanide and the other that does not. With the use of this system and flocculants, a demonstration test was conducted to apply the decontamination technology on contaminated water in two swimming pools in an elementary school located at Motomiya City, Fukushima Prefecture, Japan. It is proved from the results that both the developed purification system and the flocculants can be established as a practicable decontamination technology for contaminated water: the treatment rate was 10 m 3 /hour and the elimination factor of radioactive materials was higher than 99%. (author)

Pipe Explorer{trademark} surveying system. Innovative technology summary report

Energy Technology Data Exchange (ETDEWEB)

1999-06-01

The US Department of Energy`s (DOE) Chicago Operations Office and the DOE`s Federal Energy Technology Center (FETC) developed a Large Scale Demonstration Project (LSDP) at the Chicago Pile-5 Research Reactor (CP-5) at Argonne National Laboratory-East (ANL). The objective of the LSDP is to demonstrate potentially beneficial decontamination and decommissioning (D and D) technologies in comparison with current baseline technologies. The Pipe Explorer{trademark} system was developed by Science and Engineering Associates, Inc. (SEA), Albuquerque, NM as a deployment method for transporting a variety of survey tools into pipes and ducts. Tools available for use with the system include alpha, beta and gamma radiation detectors; video cameras; and pipe locator beacons. Different versions of this technology have been demonstrated at three other sites; results of these demonstrations are provided in an earlier Innovative Technology Summary Report. As part of a D and D project, characterization radiological contamination inside piping systems is necessary before pipes can be recycled, remediated or disposed. This is usually done manually by surveying over the outside of the piping only, with limited effectiveness and risk of worker exposure. The pipe must be accessible to workers, and embedded pipes in concrete or in the ground would have to be excavated at high cost and risk of exposure to workers. The advantage of the Pipe Explorer is its ability to perform in-situ characterization of pipe internals.

Personal Ice Cooling System (PICS). Innovative technology summary report

International Nuclear Information System (INIS)

1998-11-01

The United States Department of Energy (DOE) continually seeks safer and more cost-effective remediation technologies for use in the decontamination and decommissioning (D and D) of nuclear facilities. To this end, the Deactivation and Decommissioning Focus Area (DDFA) of the DOE's Office of Science and Technology sponsors Large-Scale Demonstration and Deployment Projects (LSDDPs) in which developers and vendors of improved or innovative technologies showcase products that are potentially beneficial to the DOE's projects and to others in the D and D community. Benefits sought include decreased health and safety risks to personnel and the environment, increased productivity, and decreased cost of operation. As buildings are demolished as part of the DOE Fernald Environmental Management Project's (FEMP's) D and D Plan, many of the activities are performed in hot weather and usually require use of various types and layers of personal protective equipment (PPE). While PPE is designed to protect the worker from contamination, it also significantly compromises the body's ability to cool itself, leading to potentially serious heat stress situations. This report describes a comparative demonstration between the methodology currently used for heat stress management (i.e., limited stay times and cool-down rooms) and an alternative personal ice cooling suit technology. The baseline methodology for heat stress management is limited stay times when working in hot conditions. The FEMP's Safety Performance Requirements outline the procedures and stay times to be followed and consider the temperature of the working environment, work load, and the type and amount of PPE required for the job. While these common criteria for determining stay times, other sites may have different requirements. This demonstration investigates the feasibility of using the personal ice cooling suite as a tool for managing heat stress in workers at the FEMP. This report provides a comparative analysis of

Personal Ice Cooling System (PICS). Innovative technology summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

The United States Department of Energy (DOE) continually seeks safer and more cost-effective remediation technologies for use in the decontamination and decommissioning (D and D) of nuclear facilities. To this end, the Deactivation and Decommissioning Focus Area (DDFA) of the DOE`s Office of Science and Technology sponsors Large-Scale Demonstration and Deployment Projects (LSDDPs) in which developers and vendors of improved or innovative technologies showcase products that are potentially beneficial to the DOE`s projects and to others in the D and D community. Benefits sought include decreased health and safety risks to personnel and the environment, increased productivity, and decreased cost of operation. As buildings are demolished as part of the DOE Fernald Environmental Management Project`s (FEMP`s) D and D Plan, many of the activities are performed in hot weather and usually require use of various types and layers of personal protective equipment (PPE). While PPE is designed to protect the worker from contamination, it also significantly compromises the body`s ability to cool itself, leading to potentially serious heat stress situations. This report describes a comparative demonstration between the methodology currently used for heat stress management (i.e., limited stay times and cool-down rooms) and an alternative personal ice cooling suit technology. The baseline methodology for heat stress management is limited stay times when working in hot conditions. The FEMP`s Safety Performance Requirements outline the procedures and stay times to be followed and consider the temperature of the working environment, work load, and the type and amount of PPE required for the job. While these common criteria for determining stay times, other sites may have different requirements. This demonstration investigates the feasibility of using the personal ice cooling suite as a tool for managing heat stress in workers at the FEMP. This report provides a comparative analysis of

[Decontamination of chemical and biological warfare agents].

Science.gov (United States)

Seto, Yasuo

2009-01-01

Chemical and biological warfare agents (CBWA's) are diverse in nature; volatile acute low-molecular-weight toxic compounds, chemical warfare agents (CWA's, gaseous choking and blood agents, volatile nerve gases and blister agents, nonvolatile vomit agents and lacrymators), biological toxins (nonvolatile low-molecular-weight toxins, proteinous toxins) and microbes (bacteria, viruses, rickettsiae). In the consequence management against chemical and biological terrorism, speedy decontamination of victims, facilities and equipment is required for the minimization of the damage. In the present situation, washing victims and contaminated materials with large volumes of water is the basic way, and additionally hypochlorite salt solution is used for decomposition of CWA's. However, it still remains unsolved how to dispose large volumes of waste water, and the decontamination reagents have serious limitation of high toxicity, despoiling nature against the environments, long finishing time and non-durability in effective decontamination. Namely, the existing decontamination system is not effective, nonspecifically affecting the surrounding non-target materials. Therefore, it is the urgent matter to build up the usable decontamination system surpassing the present technologies. The symposiast presents the on-going joint project of research and development of the novel decontamination system against CBWA's, in the purpose of realizing nontoxic, fast, specific, effective and economical terrorism on-site decontamination. The projects consists of (1) establishment of the decontamination evaluation methods and verification of the existing technologies and adaptation of bacterial organophosphorus hydrolase, (2) development of adsorptive elimination technologies using molecular recognition tools, and (4) development of deactivation technologies using photocatalysis.

Composite science and technology innovation index

International Nuclear Information System (INIS)

2011-02-01

This book reports the composite science and technology innovation index with the purpose, process, conception and, the method of evaluation. It also indicates the result of composite science and technology innovation index in 2010, which itemizes the result according to resource, activity network, environment and outcome. The last part records analysis of science and technology innovation in Korea and development plan with various analysis.

INTEGRATED VERTICAL AND OVERHEAD DECONTAMINATION SYSTEM

Energy Technology Data Exchange (ETDEWEB)

M.A. Ebadian, Ph.D.

1999-01-01

This report summarizes the activities performed during FY98 and describes the planned activities for FY99. Accomplishments for FY98 include identifying and selecting decontamination, the screening of potential characterization technologies, development of minimum performance factors for the decontamination technology, and development and identification of Applicable, Relevant and Appropriate Regulations (ARARs).

INTEGRATED VERTICAL AND OVERHEAD DECONTAMINATION SYSTEM

International Nuclear Information System (INIS)

Ebadian, M.A.

1999-01-01

This report summarizes the activities performed during FY98 and describes the planned activities for FY99. Accomplishments for FY98 include identifying and selecting decontamination, the screening of potential characterization technologies, development of minimum performance factors for the decontamination technology, and development and identification of Applicable, Relevant and Appropriate Regulations (ARARs)

Decontamination and coating of lead

International Nuclear Information System (INIS)

Rankin, W.N.; Bush, S.P.; Lyon, C.E.; Walker, V.

1988-01-01

Technology is being developed to decontaminate lead used in shielding applications in contaminated environments for recycle as shieldings. Technology is also being developed to coat either decontaminated lead or new lead before it is used in contaminated environments. The surface of the coating is expected to be much easier to decontaminate than the original lead surface. If contamination becomes severely embedded in the coating and cannot be removed, it can be easily cut with a knife and removed from the lead. The used coating can be disposed of as radioactive (hot hazardous) waste. The lead can then be recoated for further use as a shielding material

Enacting Risk in Independent Technological Innovation

DEFF Research Database (Denmark)

Berglund, Henrik; Hellström, Tomas

2002-01-01

The present study aims at investigating the role of risk in the activity of independent technological venturing. Altogether, 12 deep-interviews were conducted with technological entrepreneurs, who had taken part in the inventive, developmental and the commercialisation phases of a technology......-based innovation process. The interviews revealed a number of enactment approaches through which these innovators encountered and affected (dealt with or transformed) risk within the innovation process. Factors thus developed from the empirical material included human capital, pace and priority, the world moves...... for the benefit of innovation management....

The Kyoto mechanisms and technological innovation

DEFF Research Database (Denmark)

Lund, Henrik

2006-01-01

Climate change response, including the implementation of the Kyoto targets as the first step, calls for technological innovation of future sustainable energy systems. Based on the Danish case, this paper evaluates the type of technological change necessary. During a period of 30 years, Denmark...... countries. Consequently, the innovative technological development has changed. This paper evaluates the character of such change and makes preliminary recommendations for policies to encourage the use of the Kyoto Mechanisms as an acceleration of the necessary technological innovation....

Pathogen Decontamination of Food Crop Soil: A Review.

Science.gov (United States)

Gurtler, Joshua B

2017-09-01

The purpose of this review is to delineate means of decontaminating soil. This information might be used to mitigate soil-associated risks of foodborne pathogens. The majority of the research in the published literature involves inactivation of plant pathogens in soil, i.e., those pathogens harmful to fruit and vegetable production and ornamental plants. Very little has been published regarding the inactivation of foodborne human pathogens in crop soil. Nevertheless, because decontamination techniques for plant pathogens might also be useful methods for eliminating foodborne pathogens, this review also includes inactivation of plant pathogens, with appropriate discussion and comparisons, in the hopes that these methods may one day be validated against foodborne pathogens. Some of the major soil decontamination methods that have been investigated and are covered include chemical decontamination (chemigation), solarization, steaming, biofumigation, bacterial competitive exclusion, torch flaming, microwave treatment, and amendment with biochar. Other innovative means of inactivating foodborne pathogens in soils may be discovered and explored in the future, provided that these techniques are economically feasible in terms of chemicals, equipment, and labor. Food microbiology and food safety researchers should reach out to soil scientists and plant pathologists to create links where they do not currently exist and strengthen relationships where they do exist to take advantage of multidisciplinary skills. In time, agricultural output and the demand for fresh produce will increase. With advances in the sensitivity of pathogen testing and epidemiological tracebacks, the need to mitigate preharvest bacterial contamination of fresh produce will become paramount. Hence, soil decontamination technologies may become more economically feasible and practical in light of increasing the microbial safety of fresh produce.

An appraisal of existing decontamination technology used in the United States of America

International Nuclear Information System (INIS)

Domenech, J.S.; Frost, F.; Curran, A.R.; Grave, M.J.

1984-01-01

This report is a review of decontamination technology applied by industry to radioactively contaminated components in the U.S.A. In addition some newer techniques under development or recently emerging are discussed. Mechanical, chemical, manual and other techniques such as electropolishing and ultrasonics are reviewed. Whilst the emphasis is mainly on non-destructive techniques for components some discussion of segmentation is included as this is inevitable during concrete decontamination; and also when decontamination of components occurs as part of a decommissioning programme the use of segmentation techniques may facilitate the process. A bibliography has been included to facilitate further reading. It is important to consider the relevance of the US data in this report to the United Kingdom both to the learning curve of development and the different nuclear reactor systems in the respective countries. The authors have therefore listed some conclusions and recommendations which have become apparent to them whilst undertaking the study. (U.K.)

Decontamination of radioactive isotopes

International Nuclear Information System (INIS)

Despotovic, R.; Music, S.; Subotic, B.; Wolf, R.H.H.

1979-01-01

Removal of radioactive isotopes under controlled conditions is determined by a number of physical and chemical properties considered radiocontaminating and by the characteristics of the contaminated object. Determination of quantitative and qualitative factors for equilibrium in a contamination-decontamination system provides the basis for rational and successful decontamination. The decontamination of various ''solid/liquid'' systems is interesting from the scientific and technological point of view. These systems are of great importance in radiation protection (decontamination of various surfaces, liquids, drinking water, fixation or collection of radiocontaminants). Different types of decontamination systems are discussed. The dependence of rate and efficiency of the preparation conditions and on the ageing of the scavenger is described. The influence of coagulating electrolyte on radioactive isotope fixation efficiency was also determined. The fixation of fission radionuclide on oxide scavengers has been studied. The connection between fundamental investigations and practical decontamination of the ''solid/liquid'' systems is discussed. (author)

ASSESSMENT OF QUALITY OF INNOVATIVE TECHNOLOGIES

OpenAIRE

Larisa Alexejevna Ismagilova; Nadegda Aleksandrovna Sukhova

2016-01-01

We consider the topical issue of implementation of innovative technologies in the aircraft engine building industry. In this industry, products with high reliability requirements are developed and mass-produced. These products combine the latest achievements of science and technology. To make a decision on implementation of innovative technologies, a comprehensive assessment is carried out. It affects the efficiency of the innovations realization. In connection with this, the assessment of qu...

Analysis on the Current Status of Chemical Decontamination Technology of Steam Generators in the Oversea Nuclear Power Plants (NPPs)

Energy Technology Data Exchange (ETDEWEB)

Yoon, Taebin; Kim, Sukhoon; Kim, Juyoul; Kim, Juyub; Lee, Seunghee [FNC Technology Co. Ltd., Yongin (Korea, Republic of)

2015-10-15

The steam generators in Hanbit Unit 3 and 4 are scheduled to be replaced in 2018 and 2019, respectively. Nevertheless, the wastes from the dismantled steam generators are currently just on-site stored in the NPP because there are no disposal measures for the waste and lack of the decontamination techniques for large-sized metallic equipment. In contrast, in the oversea NPPs, there are many practical cases of chemical decontamination not only for oversized components in the NPPs such as reactor pressure vessel and steam generator, but also for major pipes. Chemical decontamination technique is more effective in decontaminating the components with complicated shape compared with mechanical one. Moreover, a high decontamination factor can be obtained by using strong solvent, and thereby most of radionuclides can be removed. Due to these advantages, the chemical decontamination has been used most frequently for operation of decontaminating the large-sized equipment. In this study, an analysis on the current status of chemical decontamination technique used for the steam generators of the foreign commercial NPPs was performed. In this study, the three major chemical decontamination processes were reviewed, which are applied to the decommissioning process of the steam generators in the commercial NPPs of the United States, Germany, and Belgium. The three processes have the different features in aspect of solvent, while those are based in common on the oxidation and reduction between the target metal surface and solvents. In addition, they have the same goals for improving the decontamination efficiency and decreasing the amount of the secondary waste generation. Based on the analysis results on component sub-processes and major advantages and disadvantages of each process, Table 2 shows the key fundamental technologies for decontamination of the steam generator in Korea and the major considerations in the development process of each technology. It is necessary to prepare

Innovation Value of Information Technology: Impact of Information Technology--Intensity on Innovation Capability and Firm Performance

Science.gov (United States)

Ramamani, Mahesh Kumar

2010-01-01

Though information technology adoptions have been always referred to as innovations in firms, much of the business value literature has concentrated on the tangible and immediately measurable impacts of information technology (IT) adoptions. This study aims to explore the impact of information technology investments on the innovativeness of a…

Irradiation technologies used for combustion gases and diluted sulfurous gases decontamination

International Nuclear Information System (INIS)

Villanueva Z, Loreto

1998-01-01

A brief description of irradiation technology used for ambient decontamination is presented here. The system is adequate fort gas and liquid effluents and solid wastes. In particular, the characteristics and applications of the irradiation done with an electron beam to gas effluent is described, mainly to clean combustion gases and other industrial gases containing sulfur and nitrogen oxides, S O x and N O x , respectively. This technology permits the remove of these contaminants and the acquisition of a solid byproduct, an ammonia sulfate-nitrate, apt for fertilizer applications. (author)

Excimer laser decontamination

Science.gov (United States)

Sentis, Marc L.; Delaporte, Philippe C.; Marine, Wladimir; Uteza, Olivier P.

2000-04-01

The application of excimer laser ablation process to the decontamination of radioactive surfaces is discussed. This technology is very attractive because it allows to efficiently remove the contaminated particles without secondary waste production. To demonstrate the capability of such technology to efficiently decontaminate large area, we studied and developed a prototype which include a XeCl laser, an optical fiber delivery system and an ablated particles collection cell. The main physical processes taking place during UV laser ablation will be explained. The influence of laser wavelength, pulse duration and absorption coefficient of material will be discussed. Special studies have been performed to understand the processes which limit the transmission of high average power excimer laser through optical fiber, and to determine the laser conditions to optimize the value of this transmission. An in-situ spectroscopic analysis of laser ablation plasma allows the real time control of the decontamination. The results obtained for painting or metallic oxides removal from stainless steel surfaces will be presented.

Integration of improved decontamination and characterization technologies in the decommissioning of the CP-5 research reactor, United States of America

Energy Technology Data Exchange (ETDEWEB)

Boing, L E; Bhattacharyya, S K [Technology Development Division, Decommissioning Program, Argonne National Laboratory, Argonne, IL (United States)

2002-02-01

The aging of research reactors worldwide has resulted in a heightened awareness in the international decommissioning community of the timeliness to review and address the needs of research reactor operators in planning for and eventually performing the decommissioning of these types of facilities. Many reactors already undergoing decommissioning can be used as test beds for evaluating enhanced or new/innovative technologies for decommissioning; it is possible that new techniques could be made available for future research reactor-decommissioning projects. Potentially, the new technologies will result in: reduced radiation doses to the work force, larger safety margins in performing decommissioning and cost and schedule savings to the decommissioners in performing the decommissioning of these facilities. Testing of these enhanced technologies for decontamination, dismantling, characterization, remote operations and worker protection are critical to furthering advancements in the technical specialty of decommissioning. Furthermore, regulatory acceptance and routine utilization for future research decommissioning will be assured by testing and developing these technologies in realistically contaminated environments prior to their use in actual research reactor decommissioning. The decommissioning of the CP-5 Research Reactor located at the ANL-East Site has been completed. In this paper we present results of work performed at Argonne National Laboratory (ANL) in the development, testing and deployment of innovative and/or enhanced technologies for the decommissioning of research reactors. In addition, details are provided on other related U.S. D and D activities, which may be useful to the international research reactor D and D community. (author)

Integration of improved decontamination and characterization technologies in the decommissioning of the CP-5 research reactor, United States of America

International Nuclear Information System (INIS)

Boing, L.E.; Bhattacharyya, S.K.

2002-01-01

The aging of research reactors worldwide has resulted in a heightened awareness in the international decommissioning community of the timeliness to review and address the needs of research reactor operators in planning for and eventually performing the decommissioning of these types of facilities. Many reactors already undergoing decommissioning can be used as test beds for evaluating enhanced or new/innovative technologies for decommissioning; it is possible that new techniques could be made available for future research reactor-decommissioning projects. Potentially, the new technologies will result in: reduced radiation doses to the work force, larger safety margins in performing decommissioning and cost and schedule savings to the decommissioners in performing the decommissioning of these facilities. Testing of these enhanced technologies for decontamination, dismantling, characterization, remote operations and worker protection are critical to furthering advancements in the technical specialty of decommissioning. Furthermore, regulatory acceptance and routine utilization for future research decommissioning will be assured by testing and developing these technologies in realistically contaminated environments prior to their use in actual research reactor decommissioning. The decommissioning of the CP-5 Research Reactor located at the ANL-East Site has been completed. In this paper we present results of work performed at Argonne National Laboratory (ANL) in the development, testing and deployment of innovative and/or enhanced technologies for the decommissioning of research reactors. In addition, details are provided on other related U.S. D and D activities, which may be useful to the international research reactor D and D community. (author)

Development of remote decontamination technologies improving internal environment of reactor buildings at Fukushima Daiichi Nuclear Power Station

International Nuclear Information System (INIS)

Hotta, Koji; Hayashi, Hirotada; Sakai, Hitoshi

2016-01-01

The reactor buildings at the Fukushima Daiichi Nuclear Power Station of Tokyo Electric Power Co., Inc., which was seriously damaged by the Great East Japan Earthquake of March 11, 2011, have been highly contaminated by radioactive materials. To safely and efficiently advance the processes related to the forthcoming decommissioning of the reactors, it is necessary to improve the hazardous environment inside the reactor buildings. During the more than four years that have elapsed since the Great East Japan Earthquake, Toshiba has been implementing various measures to reduce the ambient dose rates inside the reactor buildings through decontamination work and participation in a national project for the development of remote decontamination technologies for reactor buildings. A variety of vehicles and technologies to support decontamination work have been developed through these activities, and are significantly contributing to improvement of the environment inside the reactor buildings. (author)

Demonstration recommendations for accelerated testing of concrete decontamination methods

Energy Technology Data Exchange (ETDEWEB)

Dickerson, K.S.; Ally, M.R.; Brown, C.H.; Morris, M.I.; Wilson-Nichols, M.J.

1995-12-01

A large number of aging US Department of Energy (DOE) surplus facilities located throughout the US require deactivation, decontamination, and decommissioning. Although several technologies are available commercially for concrete decontamination, emerging technologies with potential to reduce secondary waste and minimize the impact and risk to workers and the environment are needed. In response to these needs, the Accelerated Testing of Concrete Decontamination Methods project team described the nature and extent of contaminated concrete within the DOE complex and identified applicable emerging technologies. Existing information used to describe the nature and extent of contaminated concrete indicates that the most frequently occurring radiological contaminants are {sup 137}Cs, {sup 238}U (and its daughters), {sup 60}Co, {sup 90}Sr, and tritium. The total area of radionuclide-contaminated concrete within the DOE complex is estimated to be in the range of 7.9 {times} 10{sup 8} ft{sup 2}or approximately 18,000 acres. Concrete decontamination problems were matched with emerging technologies to recommend demonstrations considered to provide the most benefit to decontamination of concrete within the DOE complex. Emerging technologies with the most potential benefit were biological decontamination, electro-hydraulic scabbling, electrokinetics, and microwave scabbling.

Demonstration recommendations for accelerated testing of concrete decontamination methods

International Nuclear Information System (INIS)

Dickerson, K.S.; Ally, M.R.; Brown, C.H.; Morris, M.I.; Wilson-Nichols, M.J.

1995-12-01

A large number of aging US Department of Energy (DOE) surplus facilities located throughout the US require deactivation, decontamination, and decommissioning. Although several technologies are available commercially for concrete decontamination, emerging technologies with potential to reduce secondary waste and minimize the impact and risk to workers and the environment are needed. In response to these needs, the Accelerated Testing of Concrete Decontamination Methods project team described the nature and extent of contaminated concrete within the DOE complex and identified applicable emerging technologies. Existing information used to describe the nature and extent of contaminated concrete indicates that the most frequently occurring radiological contaminants are 137 Cs, 238 U (and its daughters), 60 Co, 90 Sr, and tritium. The total area of radionuclide-contaminated concrete within the DOE complex is estimated to be in the range of 7.9 x 10 8 ft 2 or approximately 18,000 acres. Concrete decontamination problems were matched with emerging technologies to recommend demonstrations considered to provide the most benefit to decontamination of concrete within the DOE complex. Emerging technologies with the most potential benefit were biological decontamination, electro-hydraulic scabbling, electrokinetics, and microwave scabbling

Situations of decontamination promotion activities. Efforts by Tokyo Electric Power Company, Fukushima Revitalization Headquarters, Decontamination Promotion Office

International Nuclear Information System (INIS)

Takano, Takahiko; Ito, Kei; Takizawa, Koichi

2015-01-01

As for the decontamination of the soil contaminated with radioactive materials, decontamination is on the way in compliance with the 'Act on Special Measures Concerning the Handling of Environmental Pollution by Radioactive Materials by the NPS Accident Associated with the Tohoku District - Off the Pacific Ocean' (hereinafter, the Act on Special Measures). Tokyo Electric Power Company (TEPCO), as the party concerned to the accident, is cooperating with decontamination activities conducted by countries and municipalities under the Act on Special Measures. Total number of people cooperated by the Decontamination Promotion Office amounts to about 120,000 people. The cooperation to the decontamination by countries and municipalities covers the following fields: provision of knowledge of radiation, training of site management and supervisors, and proposal such as the decontamination method suitable for the site. As cooperation to various monitoring, there is a traveling monitoring that performs radiation measurement from the vehicles. As cooperation in the farming and industrial resumption toward the reconstruction, the group has implemented support for the distribution promotion of the holdup that was stuck in distribution due to contamination with radioactive substances. As decontamination related technology, the following are performed: (1) preparation of radiation understanding promotion tool, (2) development of precise individual dose measurement technology, and (3) development and utilization of decontamination effect analysis program. In the future, this group will perform the follow-up for decontamination, and measures toward the lifting of evacuation order. It will install the basis to perform various technical analyses on decontamination, and will further intensify technical cooperation. (A.O.)

Urethane foam void filling. Innovative technology summary report

International Nuclear Information System (INIS)

1998-12-01

Under the decontamination and decommissioning (D and D) Implementation Plan of the United States Department of Energy's (DOE's) Fernald Environmental Management Project (FEMP), non-recyclable process components and debris that are removed from buildings undergoing D and D are disposed of in an on-site disposal facility (OSDF). Critical to the design and operation of the FEMP's OSDF are provisions to protect against subsidence of the OSDF's cap. Subsidence of the cap could occur if void spaces within the OSDF were to collapse under the overburden of debris and the OSDF cap. Subsidence may create depressions in the OSDF's cap in which rainwater could collect and eventually seep into the OSDF. To minimize voids in the FEMP's OSDF, large metallic components are cut into smaller segments that can be arranged more compactly when placed in the OSDF. Component segmentation using an oxy-acetylene torch was the baseline approach used by the FEMP's D and D contractor on Plant 1, B and W Services, Inc., for the dismantlement and size-reduction of large metal components. Although this technology has performed satisfactorily, it is time-consuming, labor-intensive and costly. Use of the oxy-acetylene torch exposes workers to health and safety hazards including the risk of burns, carbon monoxide, and airborne contamination of residual lead-based paints and other contaminants on the surface of the components being segmented. In addition, solvents used to remove paint from the components before segmenting them emit flammable, noxious fumes. This demonstration investigated the feasibility of placing large vessels intact in the OSDF without segmenting them. To prevent the walls of the vessels from collapsing under the overburden or from degradation, an innovative approach was employed which involved filling the voids in the vessels with a fluid material that hardened on standing. The hardened filling would support the walls of the vessels, and prevent them from collapsing. This report

Achievements of Theoretical Research on Chinese Technological Innovation

Directory of Open Access Journals (Sweden)

Wang Hanxi

2017-01-01

Full Text Available Using the CNKI database as the sample source, we investigated the makeup of current research results on Chinese technological innovation, and found that the study of Chinese technological innovation consists of nine directions - underlying principles of innovation behavior, concepts of innovation cognition, methods of innovation, behavior of innovation subjects, structure of innovation mediators, innovation capacity, public service system of innovation, policy support system of innovation, and cultural environment of innovation, as well as several issues of innovation, including its behavior mechanism, operational mechanism, work mechanism, modes of implementation, modes of mathematical representation, modes of physical representation, modes of behavioral representation, modes of performance representation, modes of function realization, modes of structure realization, modes of workflow realization, modes of carrier realization, etc. Such a scattered makeup requires us to formulate the system of Chinese technological innovation achievements from the perspective of philosophy of science. This will be an important mission in the study of Chinese technological innovation.

Technology Audit: Assessment of Innovative Portfolio

Directory of Open Access Journals (Sweden)

Kurushina Viktoria

2016-01-01

Full Text Available The article discusses the features of the technological audit performing in the companies of oil and gas sector of Russian economy. To measure the innovations quality level the scale was developed based on the Theory of Inventive Problem Solving and the theory of technological structures. Figures of the innovations quantity by levels, volume and quality of the innovative portfolio are offered for assessment the innovative portfolio quality. The method was tested on an example of oil and gas transporting enterprises. The results of the comparative analysis of innovative portfolio are shown.

Technological Innovations in Forensic Genetics

DEFF Research Database (Denmark)

Wienroth, Matthias; Morling, Niels; Williams, Robin

2014-01-01

This paper discusses the nature of four waves of technological innovations in forensic genetics alongside the social, legal and ethical aspect of these innovations. It emphasises the way in which technological advances and their socio-legal frameworks are co-produced, shaping technology...... expectations, social identities, and legal institutions. It also considers how imagined and actual uses of forensic genetic technologies are entangled with assertions about social order, affirmations of common values and civil rights, and promises about security and justice. Our comments seek to encourage...

Innovation investment area: Technology summary

Energy Technology Data Exchange (ETDEWEB)

1994-03-01

The mission of Environmental Management`s (EM) Office of Technology Development (OTD) Innovation Investment Area is to identify and provide development support for two types of technologies that are developed to characterize, treat and dispose of DOE waste, and to remediate contaminated sites. They are: technologies that show promise to address specific EM needs, but require proof-of-principle experimentation; and (2) already proven technologies in other fields that require critical path experimentation to demonstrate feasibility for adaptation to specific EM needs. The underlying strategy is to ensure that private industry, other Federal Agencies, universities, and DOE National Laboratories are major participants in developing and deploying new and emerging technologies. To this end, about 125 different new and emerging technologies are being developed through Innovation Investment Area`s (IIA) two program elements: RDDT&E New Initiatives (RD01) and Interagency Agreements (RD02). Both of these activities are intended to foster research and development partnerships so as to introduce innovative technologies into other OTD program elements for expedited evaluation.

Innovation investment area: Technology summary

International Nuclear Information System (INIS)

1994-03-01

The mission of Environmental Management's (EM) Office of Technology Development (OTD) Innovation Investment Area is to identify and provide development support for two types of technologies that are developed to characterize, treat and dispose of DOE waste, and to remediate contaminated sites. They are: technologies that show promise to address specific EM needs, but require proof-of-principle experimentation; and (2) already proven technologies in other fields that require critical path experimentation to demonstrate feasibility for adaptation to specific EM needs. The underlying strategy is to ensure that private industry, other Federal Agencies, universities, and DOE National Laboratories are major participants in developing and deploying new and emerging technologies. To this end, about 125 different new and emerging technologies are being developed through Innovation Investment Area's (IIA) two program elements: RDDT ampersand E New Initiatives (RD01) and Interagency Agreements (RD02). Both of these activities are intended to foster research and development partnerships so as to introduce innovative technologies into other OTD program elements for expedited evaluation

Technological Innovation, R & D Activities and Innovation System Between Organizations

Directory of Open Access Journals (Sweden)

Jonas Pedro Fabris

2015-08-01

Full Text Available This theoretical paper aimed to explicit, through the rescue of theoretical assumptions, the innovation, the innovation system, and the research and development (R & D activities. The innovation, especially technological innovation, is now seen as essential in differentiation strategies, competitiveness and growth in a greater number of businesses. Innovation is not only the result of financial investments by companies. For it to exist, it is necessary the existence of innovative capacity that should be present at all stages of the innovation process, and a favorable institutional environment and, increasingly, of specific incentive policies. That is, there are internal and external factors to companies and other institutions involved in the process. Innovation systems were discovered to resolve the variations in the degree of competitiveness of different economies and, above all, in relation to the technological performance and the ability to innovate these economies face the growing importance of international markets for high-tech products. Thus, it was found that successful innovators are not successful just because of their personal qualities and actions but as a result of their interaction with research and innovation systems that inhabit the quality of such systems.

Stimulating technological innovation : problem identification and intervention formulation with the technological innovation systems framework

OpenAIRE

Kieft, A.C.

2017-01-01

The technological innovation systems (TIS) framework provides a theory to understand under what conditions technological innovations are successfully developed and implemented. The objective of this dissertation is to further strengthen this TIS intervention framework, which is the part of the TIS theoretical framework that facilitates the identification of inhibiting problems and the formulation of interventions. Theoretical adaptations and extensions are proposed and their merits subsequent...

Y-12 Plant decontamination and decommissioning technology logic diagram for Building 9201-4. Volume 3: Technology evaluation data sheets; Part A: Characterization, dismantlement

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 (TLD) was developed to provide a decision-support tool that relates decontamination and decommissioning (D and D) problems at Bldg. 9201-4 to potential technologies that can remediate these problems. The TLD uses information from the Strategic Roadmap for the Oak Ridge Reservation, the Oak Ridge K-25 Site Technology Logic Diagram, the Oak Ridge National Laboratory Technology Logic Diagram, and a previous Hanford logic diagram. This TLD identifies the research, development, demonstration, testing, and evaluation needed for sufficient development of these technologies to allow for technology transfer and application to D and D and waste management (WM) activities. It is essential that follow-on engineering studies be conducted to build on the output of this project. These studies will begin by selecting the most promising technologies identified in the TLD and by finding an optimum mix of technologies that will provide a socially acceptable balance between cost and risk. This report consists of the characterization and dismantlement data sheets.

Y-12 Plant decontamination and decommissioning technology logic diagram for Building 9201-4. Volume 3: Technology evaluation data sheets; Part A: Characterization, dismantlement

International Nuclear Information System (INIS)

1994-09-01

The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 (TLD) was developed to provide a decision-support tool that relates decontamination and decommissioning (D and D) problems at Bldg. 9201-4 to potential technologies that can remediate these problems. The TLD uses information from the Strategic Roadmap for the Oak Ridge Reservation, the Oak Ridge K-25 Site Technology Logic Diagram, the Oak Ridge National Laboratory Technology Logic Diagram, and a previous Hanford logic diagram. This TLD identifies the research, development, demonstration, testing, and evaluation needed for sufficient development of these technologies to allow for technology transfer and application to D and D and waste management (WM) activities. It is essential that follow-on engineering studies be conducted to build on the output of this project. These studies will begin by selecting the most promising technologies identified in the TLD and by finding an optimum mix of technologies that will provide a socially acceptable balance between cost and risk. This report consists of the characterization and dismantlement data sheets

Governance and commercialization of technological innovation

International Nuclear Information System (INIS)

Fidanza, Andrea

2015-01-01

Technological innovation is not only a direct result of the economic resources allocated to research and development activities. It is also the result of the creation and organization of a complex innovation system that aims to involve different actors and stake holders along a process based on different stages ranging from scientific discovery to technological maturity. Risk and funds sharing between public and private sectors is a key element for the transition of a technology towards its commercialization, without which the innovation process is likely to remain trapped in the so-called “Valley of death” of a technology. Overcoming this barrier request a process based on three pillars: research, demonstration and production of a specific technology [it

Decision Analysis Science Modeling for Application and Fielding Selection Applied to Equipment Dismantlement Technologies. Final Report January 1998

International Nuclear Information System (INIS)

Lagos, L.E.; Ebadian, M.A.

1998-01-01

During the decontamination and decommissioning (D and D) activities being conducted by the U.S. Department of Energy (DOE), approximately 550,000 metric tons of contaminated metal will be generated by the disposition of contaminated buildings. The majority of the structural steel is considered to be radiologically contaminated. The D and D activities require the treatment of the structural steel to reduce occupational and environmental radiological exposures during dismantlement. Treatment technologies may also be required for possible recycling. Many proven commercial treatment technologies are available. These treatment processes vary in aggressiveness, safety requirements, secondary waste generation, necessary capital, and operation and maintenance costs. Choosing the appropriate technology to meet the decontamination objectives for structural steel is a difficult process. A single information source comparing innovative and nuclear and non-nuclear technologies in the areas of safety, cost and effectiveness is not currently commercially available to perform a detailed analysis. This study presents comparable data related to operation and maintenance, cost, and health and safely aspects of three readily available technologies and one innovative technology for nuclear decontamination. The technologies include Advance Recyclable Media System (ARMStrademark), NELCO Porta Shot Blasttrademark (JHJ-2000), Pegasus Coating Removal System 7 (PCRS-7) and the innovative laser ablation technology called the Yag Erasertrademark

The Impact of Technological and Non-Technological Innovations on Firm Growth

OpenAIRE

Ali-Yrkkö, Jyrki; Martikainen, Olli

2008-01-01

This study investigates the relationship between innovations and firm growth, based on the data of Finnish firms operating in the software industry. We find that in terms of turnover and employment, firms with only technological innovations do not grow more rapidly than other firms. However, firm growth is positively associated with the combination of technological and non-technological innovations.

National Innovation System and Disruptive Innovations in Synthetic Rubber and Tire Technology

Directory of Open Access Journals (Sweden)

Ray R. Gehani

2008-01-01

Full Text Available The current models of National Innovation Systems (NIS are based on interactions and learning across three institutions: government, university and industry. This empirical study of the evolution of innovations in rubber and tire technologies such as the collaborative innovative suppliers (of raw materials and human capital and disruptive rival innovators to the traditional tri-helical model of National Innovation System. This was empirically examined for the evolution of rubber and tire technology and the rise and decline of its innovative region: the Rubber Capital of the World in Akron, Ohio.

Chemical decontamination of process equipment using recyclable chelating solvent Phase I. Final report, September 1993--June 1995

International Nuclear Information System (INIS)

1995-10-01

The Department of Energy (DOE) is now faced with the task of meeting decontamination and decommissioning obligations at numerous facilities by the year 2019. Due to the tremendous volume of material involved, innovative decontamination technologies are being sought that can reduce the volumes of contaminated waste materials and secondary wastes requiring disposal. With sufficient decontamination, some of the material from DOE facilities could be released as scrap into the commercial sector for recycle, thereby reducing the volume of radioactive waste requiring disposal. Although recycling may initially prove to be more costly than current disposal practices, rapidly increasing disposal costs are expected to make recycling more and more cost effective. Additionally, recycling is now perceived as the ethical choice in a world where the consequences of replacing resources and throwing away reusable materials are impacting the well-being of the environment

Decontamination, decommissioning, and vendor advertorial issue, 2008

Energy Technology Data Exchange (ETDEWEB)

Agnihotri, Newal (ed.)

2008-07-15

The focus of the July-August issue is on Decontamination, decommissioning, and vendor advertorials. Articles and reports in this issue include: D and D technical paper summaries; The role of nuclear power in turbulent times, by Tom Chrisopher, AREVA, NP, Inc.; Enthusiastic about new technologies, by Jack Fuller, GE Hitachi Nuclear Energy; It's important to be good citizens, by Steve Rus, Black and Veatch Corporation; Creating Jobs in the U.S., by Guy E. Chardon, ALSTOM Power; and, and, An enviroment and a community champion, by Tyler Lamberts, Entergy Nuclear Operations, Inc. The Industry Innovations article is titled Best of the best TIP achievement 2008, by Edward Conaway, STP Nuclear Operating Company.

Combining the technological innovation systems framework with the entrepreneurs’ perspective on innovation

NARCIS (Netherlands)

Planko, Julia; Cramer, Jacqueline; Hekkert, Marko P.; Chappin, Maryse M H

2017-01-01

For their technological sustainability innovations to become successful, entrepreneurs can strategically shape the technological field in which they are involved. The technological innovation systems (TISs) literature has generated valuable insights into the processes which need to be stimulated for

Regulatory barriers to hazardous waste technology innovation

International Nuclear Information System (INIS)

Kuusinen, T.L.; Siegel, M.R.

1991-02-01

The primary federal regulatory programs that influence the development of new technology for hazardous waste are the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA, also commonly known as Superfund). Two important aspects of RCRA that can create barriers to hazardous waste technology innovation are technology-based waste pre-treatment standards and a cumbersome permitting program. By choosing a technology-based approach to the RCRA land disposal restrictions program, the US Environmental Protection Agency (EPA) has simultaneously created tremendous demand for the technologies specified in its regulations, while at the same time significantly reduced incentives for technology innovation that might have otherwise existed. Also, the RCRA hazardous waste permitting process can take years and cost hundreds of thousands of dollars. The natural tendency of permit writers to be cautious of unproven (i.e., innovative) technology also can create a barrier to deployment of new technologies. EPA has created several permitting innovations, however, to attempt to mitigate this latter barrier. Understanding the constraints of these permitting innovations can be important to the success of hazardous waste technology development programs. 3 refs

Technological Innovation in Primary Education

Directory of Open Access Journals (Sweden)

Luisana Sleny López Alvarado

2018-05-01

Full Text Available The purpose of this essay is to reflect on technological innovation in Primary Education. In this idea, information processing was used to support the analysis of the theoretical approaches related to the relevance of education that is based on a significant pedagogical practice capable of developing the capacities and interests, so that they can appropriate the global and local content in the vision of access to information, considering social opportunities. The restructuring to which education has been subjected has been influenced by advances in science, technology and the demands of a complex, dynamic and uncertain society in the processes of educational innovation, which involves the introduction of something new in education. the educational system, modifying its teaching-learning structures through the incorporation of Information and Communication Technologies (ICT in the curricular design of primary education in its intention to train for incursion into science and technology from use of a wide range of didactic resources that lead to pedagogical innovation. It was concluded that technological innovation in the educational praxis of primary education, requires in addition to the vocation of service, to study the new didactic paradigms to display their reflective capacity and assume the commitment to acquire digital literacy to assume the requirements of a knowledge society which is increasingly globalized.

Decontamination demonstration facility (D.D.F) modularization/mobility study

International Nuclear Information System (INIS)

FitzPatrick, V.F.; Butts, H.L.; Moles, R.G.; Lundgren, R.A.

1980-11-01

The component decontamination technology, developed under the DOE sponsored TRU Waste Decontamination Program, has potential benefits to nuclear utility owners in four strategic areas: (1) Meeting ALARA Criteria for Maintenance/Operations; (2) Management of wastes and waste forms; (3) Accident Response; (4) Decommissioning. The most significant step in transferring this technology directly to the nuclear industry is embodied in the TMI Decontamination Demonstration Facility

Research on process management of nuclear power technological innovation

International Nuclear Information System (INIS)

Yang Hua; Zhou Yu

2005-01-01

Different from the other technological innovation processes, the technological innovation process of nuclear power engineering project is influenced deeply by the extensive environmental factors, the technological innovation of nuclear power engineering project needs to make an effort to reduce environmental uncertainty. This paper had described the mechanism of connection technological innovation process of nuclear power engineering project with environmental factors, and issued a feasible method based on model of bargaining to incorporate technological innovation process management of nuclear power engineering project with environmental factors. This method has realistic meanings to guide the technological innovation of nuclear power engineering project. (authors)

Concrete shaver. Innovative technology summary report

International Nuclear Information System (INIS)

1998-12-01

The US Department of Energy (DOE) is in the process of decontamination and decommissioning (D and D) for many of its nuclear facilities throughout the United States. These facilities must be dismantled and the demolition waste sized into manageable pieces for handling and disposal. The facilities undergoing D and D are typically chemically and/or radiologically contaminated. To facilitate this work, DOE requires a tool capable of removing the surface of radiologically contaminated concrete floors. Operating requirements for the tool include simple and economical operation, the capability of operating in ambient temperatures from 3 C to 40 C (37 F to 104 F), and the ability to be easily decontaminated. The tool also must be safe for workers. The Marcrist Industries Limited concrete shaver is an electrically driven, self-propelled concrete and coating removal system. This technology consists of a 25-cm (10-in.)-wide diamond impregnated shaving drum powered by an electric motor and contains a vacuum port for dust extraction. The concrete shaver is ideal for use on open, flat, floor areas. The shaver may also be used on slightly curved surfaces. This shaver is self-propelled and produces a smooth, even surface with little vibration. The concrete shaver is an attractive alternative to traditional pneumatic scabbling tools, which were considered the baseline in this demonstration. The use of this tool reduces worker fatigue (compared to the baseline) due to lower vibration. The shaver is more than five times faster than the five-piston pneumatic scabbler at removing contamination from concrete. Because of this increased productivity, the shaver is 50% less costly to operate than baseline technologies. The DOE has successfully demonstrated the concrete shaver for decontaminating floors for free-release surveys prior to demolition work

Decontamination system study for the Tank Waste Retrieval System

International Nuclear Information System (INIS)

Reutzel, T.; Manhardt, J.

1994-05-01

This report summarizes the findings of the Idaho National Engineering Laboratory's decontamination study in support of the Tank Waste Retrieval System (TWRS) development program. Problems associated with waste stored in existing single shell tanks are discussed as well as the justification for the TWRS program. The TWRS requires a decontamination system. The subsystems of the TWRS are discussed, and a list of assumptions pertinent to the TWRS decontamination system were developed. This information was used to develop the functional and operational requirements of the TWRS decontamination system. The requirements were combined with a comprehensive review of currently available decontamination techniques to produced a set of evaluation criteria. The cleaning technologies and techniques were evaluated, and the CO 2 blasting decontamination technique was chosen as the best technology for the TWRS

MERCURY CONTAMINATED MATERIAL DECONTAMINATION METHODS: INVESTIGATION AND ASSESSMENT

Energy Technology Data Exchange (ETDEWEB)

M.A. Ebadian, Ph.D.

2001-01-01

Over the years mercury has been recognized as having serious impacts on human health and the environment. This recognition has led to numerous studies that deal with the properties of various mercury forms, the development of methods to quantify and speciate the forms, fate and transport, toxicology studies, and the development of site remediation and decontamination technologies. This report reviews several critical areas that will be used in developing technologies for cleaning mercury from mercury-contaminated surfaces of metals and porous materials found in many DOE facilities. The technologies used for decontamination of water and mixed wastes (solid) are specifically discussed. Many technologies that have recently appeared in the literature are included in the report. Current surface decontamination processes have been reviewed, and the limitations of these technologies for mercury decontamination are discussed. Based on the currently available technologies and the processes published recently in the literature, several processes, including strippable coatings, chemical cleaning with iodine/iodide lixiviant, chemisorbing surface wipes with forager sponge and grafted cotton, and surface/pore fixation through amalgamation or stabilization, have been identified as potential techniques for decontamination of mercury-contaminated metal and porous surfaces. Their potential merits and applicability are discussed. Finally, two processes, strippable coatings and chemical cleaning with iodine/iodide lixiviant, were experimentally investigated in Phase II of this project.

Decommissioning and Decontamination

International Nuclear Information System (INIS)

Massaut, V.

2000-01-01

The objectives of SCK-CEN's decommissioning and decontamination programme are (1) to develop, test and optimise the technologies and procedures for decommissioning and decontamination of nuclear installations in order to minimise the waste arising and the distributed dose; (2) to optimise the environmental impact; (3) to reduce the cost of the end-of-life of the installation; (4) to make these new techniques available to the industry; (5) to share skills and competences. The programme and achievements in 1999 are summarised

Studying Innovation Technologies in Modern Education

Science.gov (United States)

Stukalenko, Nina M.; Zhakhina, Bariya B.; Kukubaeva, Asiya K.; Smagulova, Nurgul K.; Kazhibaeva, Gulden K.

2016-01-01

In modern society, innovation technologies expand to almost every field of human activity, including such wide field as education. Due to integrating innovation technologies into the educational process practice, this phenomenon gained special significance within improvement and modernization of the established educational system. Currently, the…

From translational research to open technology innovation systems.

Science.gov (United States)

Savory, Clive; Fortune, Joyce

2015-01-01

The purpose of this paper is to question whether the emphasis placed within translational research on a linear model of innovation provides the most effective model for managing health technology innovation. Several alternative perspectives are presented that have potential to enhance the existing model of translational research. A case study is presented of innovation of a clinical decision support system. The paper concludes from the case study that an extending the triple helix model of technology transfer, to one based on a quadruple helix, present a basis for improving the performance translational research. A case study approach is used to help understand development of an innovative technology within a teaching hospital. The case is then used to develop and refine a model of the health technology innovation system. The paper concludes from the case study that existing models of translational research could be refined further through the development of a quadruple helix model of heath technology innovation that encompasses greater emphasis on user-led and open innovation perspectives. The paper presents several implications for future research based on the need to enhance the model of health technology innovation used to guide policy and practice. The quadruple helix model of innovation that is proposed can potentially guide alterations to the existing model of translational research in the healthcare sector. Several suggestions are made for how innovation activity can be better supported at both a policy and operational level. This paper presents a synthesis of the innovation literature applied to a theoretically important case of open innovation in the UK National Health Service. It draws in perspectives from other industrial sectors and applies them specifically to the management and organisation of innovation activities around health technology and the services in which they are embedded.

Rethinking the Market - Technology Relationship for Innovation

DEFF Research Database (Denmark)

Howells, John

This paper revisits the 'what causes innovation - market pull or technology push?' debate to argue that the conceptualisation is flawed and that the firm is the only 'agent' capable of innovative action. The paper differentiates between 'use', 'need' and 'intended use' to obtain greater precision...... with respect to the technology-market matching process that is fundamental to innovation. The validity of the approach is demonstrated through empirical examples. These examples also show the value of distinguishing between two types of market concept used by the innovating firm. These are the 'reference...... market' which is a traded product that is a principal source of 'use' ideas for the mental construction of the 'innovation market' concept. It is the latter that can be thought to guide the construction of innovative production technology....

Unmet needs: relevance to medical technology innovation?

Science.gov (United States)

McCarthy, Avril D; Sproson, Lise; Wells, Oliver; Tindale, Wendy

2014-01-01

This paper describes and discusses the role of unmet needs in the innovation of new medical technologies using the National Institute for Health Research Devices for Dignity (D4D) Healthcare Technology Co-operative as a case study. It defines an unmet need, providing a spectrum of classification and discusses the benefits and the challenges of identifying unmet need and its influence on the innovation process. The process by which D4D has captured and utilized unmet needs to drive technology innovation is discussed and examples given. It concludes by arguing that, despite the challenges, defining and reviewing unmet need is a fundamental factor in the success of medical technology innovation.

Making technological innovation work for sustainable development

Science.gov (United States)

Anadon, Laura Diaz; Harley, Alicia G.; Matus, Kira; Moon, Suerie; Murthy, Sharmila L.

2016-01-01

This paper presents insights and action proposals to better harness technological innovation for sustainable development. We begin with three key insights from scholarship and practice. First, technological innovation processes do not follow a set sequence but rather emerge from complex adaptive systems involving many actors and institutions operating simultaneously from local to global scales. Barriers arise at all stages of innovation, from the invention of a technology through its selection, production, adaptation, adoption, and retirement. Second, learning from past efforts to mobilize innovation for sustainable development can be greatly improved through structured cross-sectoral comparisons that recognize the socio-technical nature of innovation systems. Third, current institutions (rules, norms, and incentives) shaping technological innovation are often not aligned toward the goals of sustainable development because impoverished, marginalized, and unborn populations too often lack the economic and political power to shape innovation systems to meet their needs. However, these institutions can be reformed, and many actors have the power to do so through research, advocacy, training, convening, policymaking, and financing. We conclude with three practice-oriented recommendations to further realize the potential of innovation for sustainable development: (i) channels for regularized learning across domains of practice should be established; (ii) measures that systematically take into account the interests of underserved populations throughout the innovation process should be developed; and (iii) institutions should be reformed to reorient innovation systems toward sustainable development and ensure that all innovation stages and scales are considered at the outset. PMID:27519800

Making technological innovation work for sustainable development.

Science.gov (United States)

Anadon, Laura Diaz; Chan, Gabriel; Harley, Alicia G; Matus, Kira; Moon, Suerie; Murthy, Sharmila L; Clark, William C

2016-08-30

This paper presents insights and action proposals to better harness technological innovation for sustainable development. We begin with three key insights from scholarship and practice. First, technological innovation processes do not follow a set sequence but rather emerge from complex adaptive systems involving many actors and institutions operating simultaneously from local to global scales. Barriers arise at all stages of innovation, from the invention of a technology through its selection, production, adaptation, adoption, and retirement. Second, learning from past efforts to mobilize innovation for sustainable development can be greatly improved through structured cross-sectoral comparisons that recognize the socio-technical nature of innovation systems. Third, current institutions (rules, norms, and incentives) shaping technological innovation are often not aligned toward the goals of sustainable development because impoverished, marginalized, and unborn populations too often lack the economic and political power to shape innovation systems to meet their needs. However, these institutions can be reformed, and many actors have the power to do so through research, advocacy, training, convening, policymaking, and financing. We conclude with three practice-oriented recommendations to further realize the potential of innovation for sustainable development: (i) channels for regularized learning across domains of practice should be established; (ii) measures that systematically take into account the interests of underserved populations throughout the innovation process should be developed; and (iii) institutions should be reformed to reorient innovation systems toward sustainable development and ensure that all innovation stages and scales are considered at the outset.

Feasibility study of micro-filtration for algae separation in an innovative nuclear effluents decontamination process

International Nuclear Information System (INIS)

Gouvion Saint Cyr, D. de; Wisniewski, C.; Schrive, L.; Farhi, E.; Rivasseau, C.

2014-01-01

Bio-remediation technologies often offer efficiency, cost and environmental impact benefits against physico-chemical technologies. Concerning the remediation of radionuclide-containing water, a few bio-based technologies have been proposed but none is currently operational in highly radioactive environments. A new radio-tolerant micro-alga, isolated from a nuclear facility, possesses properties that offer new decontamination prospects for the nuclear industry or for the clean-up of environmental water. A pilot-scale treatment unit based on this alga is currently under development for the decontamination of radioactive water. It includes separation and/or concentration steps relying on membrane filtration. This work aims at verifying the feasibility of micro-filtration as separation step for the targeted algae separation. Recommendations about the choice of operating conditions limiting and/or controlling the membrane fouling are provided with the objective to enhance the separation efficiency. Lab-scale dead-end filtration tests were implemented and the key factors involved in the separation performances were investigated. Membrane characteristics, biomass composition, and hydrodynamic conditions were considered. Organic membranes provided adequate filtration performance. Membrane fouling was essentially induced by a rapid reversible algae deposit and to a lesser extent by irreversible pore blockage caused by smaller particles and dissolved organic matter. To cancel the reversible fouling, hydrodynamic actions such as stirring and back-flush efficiently prevented algae deposit, allowing higher filtration productivity. This study demonstrates the feasibility of membrane separation for micro-algae harvesting at laboratory-scale and specifies the suitable working conditions. (authors)

Technology and Innovation in Adult Learning

Science.gov (United States)

King, Kathy P.

2017-01-01

"Technology and Innovation in Adult Learning" introduces educators and students to the intersection of adult learning and the growing technological revolution. Written by an internationally recognized expert in the field, this book explores the theory, research, and practice driving innovation in both adult learning and learning…

Feasibility studies and technological innovation

DEFF Research Database (Denmark)

Hvelplund, Frede Kloster; Lund, Henrik; Sukkumnoed, Decharut

2004-01-01

The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives.......The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives....

Innovative technology summary report: Concrete grinder

International Nuclear Information System (INIS)

1998-09-01

The Flex concrete grinder is a lightweight, hand-held concrete and coating removal system used for decontaminating or stripping concrete surfaces. The US Department of Energy has successfully demonstrated it for decontaminating walls and floors for free release surveys prior to demolition work. The grinder is an electric-powered tool with a vacuum port for dust extraction and a diamond grinding wheel. The grinder is suitable for flat or slightly curved surfaces and results in a smooth surface, which makes release surveys more reliable. The grinder is lightweight and produces very little vibration, thus reducing worker fatigue. The grinder is more efficient than traditional baseline, tools at removing contamination from concrete surfaces (more than four times faster than hand-held pneumatic scabbling and scaling tools). Grinder consumables (i.e., replacement diamond grinding wheel) are more expensive than the replacement carbide parts for the scaler and scabbler. However, operating costs are outweighed by the lower purchase price of the grinder (50% of the price of the baseline scaler and 8% of the price of the baseline scabbler). Overall, the concrete grinder is an attractive alternative to traditional scabbling and scaling pneumatic tools. To this end, in July 1998, the outer rod room exposed walls of the Safe Storage Enclosure (SSE), an area measuring approximately 150 m 2 , may be decontaminated with the hand-held grinder. This concrete grinder technology was demonstrated for the first time at the DOE's Hanford Site. Decontamination of a sample room walls was performed at the C Reactor to free release the walls prior to demolition. The demonstration was conducted by onsite D and D workers, who were instructed by the vendor prior to and during the demonstration

Making technological innovation work for sustainable development

OpenAIRE

Anadon, Laura Diaz; Chan, Gabriel; Harley, Alicia G.; Matus, Kira; Moon, Suerie; Murthy, Sharmila L.; Clark, William C.

2016-01-01

Sustainable development requires harnessing technological innovation to improve human well-being in current and future generations. However, poor, marginalized, and unborn populations too often lack the economic or political power to shape innovation processes to meet their needs. Issues arise at all stages of innovation, from invention of a technology through its selection, production, adaptation, adoption, and retirement. Three insights should inform efforts to intervene in innovation syste...

A survey of decontamination processes applicable to DOE nuclear facilities

International Nuclear Information System (INIS)

Chen, L.; Chamberlain, D.B.; Conner, C.; Vandegrift, G.F.

1997-05-01

The objective of this survey was to select an appropriate technology for in situ decontamination of equipment interiors as part of the decommissioning of U.S. Department of Energy nuclear facilities. This selection depends on knowledge of existing chemical decontamination methods. This report provides an up-to-date review of chemical decontamination methods. According to available information, aqueous systems are probably the most universally used method for decontaminating and cleaning metal surfaces. We have subdivided the technologies, on the basis of the types of chemical solvents, into acid, alkaline permanganate, highly oxidizing, peroxide, and miscellaneous systems. Two miscellaneous chemical decontamination methods (electrochemical processes and foam and gel systems) are also described. A concise technical description of various processes is given, and the report also outlines technical considerations in the choice of technologies, including decontamination effectiveness, waste handing, fields of application, and the advantages and limitations in application. On the basis of this survey, six processes were identified for further evaluation. 144 refs., 2 tabs

A survey of decontamination processes applicable to DOE nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

Chen, L.; Chamberlain, D.B.; Conner, C.; Vandegrift, G.F.

1997-05-01

The objective of this survey was to select an appropriate technology for in situ decontamination of equipment interiors as part of the decommissioning of U.S. Department of Energy nuclear facilities. This selection depends on knowledge of existing chemical decontamination methods. This report provides an up-to-date review of chemical decontamination methods. According to available information, aqueous systems are probably the most universally used method for decontaminating and cleaning metal surfaces. We have subdivided the technologies, on the basis of the types of chemical solvents, into acid, alkaline permanganate, highly oxidizing, peroxide, and miscellaneous systems. Two miscellaneous chemical decontamination methods (electrochemical processes and foam and gel systems) are also described. A concise technical description of various processes is given, and the report also outlines technical considerations in the choice of technologies, including decontamination effectiveness, waste handing, fields of application, and the advantages and limitations in application. On the basis of this survey, six processes were identified for further evaluation. 144 refs., 2 tabs.

The Center for Environmental Technology Innovative Technology Screening Process

International Nuclear Information System (INIS)

Bertrand, C.M.

1995-02-01

The Center for Environmental Technology's (CET) mission is to provide a fully integrated system for accelerated evaluation, development, commercialization, and public acceptance of creative environmental solutions which match the foremost demands in today's environmentally sensitive world. In short, CET will create a means to provide quick, effective solutions for environmental needs. To meet this mission objective, CET has created a unique and innovative approach to eliminating the usual barriers in developing and testing environmental technologies. The approach paves the way for these emerging, cutting-edge technologies by coordinating environmental restoration and waste management activities of industry, universities, and the government to: efficiently and effectively transfer technology to these users, provide market-driven, cost-effective technology programs to the public and DOE, and aid in developing innovative ideas by initiating efforts between DOE facilities and private industry. The central part to this mission is selecting and evaluating specific innovative technologies for demonstration and application at United States Department of Energy (DOE) installations. The methodology and criteria used for this selection, which is called the CET Innovative Technology Screening Process, is the subject of this paper. The selection criteria used for the screening process were modeled after other DOE technology transfer programs and were further developed by CET's Technology Screening and Evaluation Board (TSEB). The process benefits both CET and the proposing vendors by providing objective selection procedures based on predefined criteria. The selection process ensures a rapid response to proposing vendors, all technologies will have the opportunity to enter the selection process, and all technologies are evaluated on the same scale and with identical criteria

Technology, Innovation and Knowledge

DEFF Research Database (Denmark)

Andersson, Ulf; Dasi, Angels; Mudambi, Ram

2016-01-01

The relevance of ideas is at the core of the IB field and has been captured in concepts like technology, innovation and knowledge. While these concepts have evolved over the last decades, the point that the ideas and the international connectivity are central for IB remains genuine. This paper...... is an attempt to take stock of the evolution of the concepts technology, innovation and knowledge in IB literature along the past five decades with a particular focus on the role of the Columbia Journal of World Business (CJWB) and the Journal of World Business (JWB) in this evolution. Likewise, our objective...

Geographic assistance of decontamination strategy elaboration

International Nuclear Information System (INIS)

Davydchuk, V.; Arapis, G.

1996-01-01

Those who elaborates the strategy of decontamination of vast territories is to take into consideration the heterogeneity of such elements of landscape as relief, lithology, humidity and types of soils and, vegetation, both on local and regional level. Geographic assistance includes evaluation of efficacy of decontamination technologies in different natural conditions, identification of areas of their effective application and definition of ecological damage, estimation of balances of the radionuclides in the landscapes to create background of the decontamination strategy

DOE's Innovative Treatment Remediation Demonstration Program accelerating the implementation of innovative technologies

International Nuclear Information System (INIS)

Hightower, M.

1995-01-01

A program to help accelerate the adoption and implementation of new and innovative remediation technologies has been initiated by the Department of Energy's (DOE) Environmental Restoration Program Office (EM40). Developed as a Public-Private Partnership program in cooperation with the US Environmental Protection Agency's (EPA) Technology Innovation Office (TIO) and coordinated by Sandia National Laboratories, the Innovative Treatment Remediation Demonstration (ITRD) Program attempts to reduce many of the classic barriers to the use of new technologies by involving government, industry, and regulatory agencies in the assessment, implementation, and validation of innovative technologies. In this program, DOE facilities work cooperatively with EPA, industry, national laboratories, and state and federal regulatory agencies to establish remediation demonstrations using applicable innovative technologies at their sites. Selected innovative technologies are used to remediate small, one to two acre, sites to generate the full-scale and real-world operating, treatment performance, and cost data needed to validate these technologies and gain acceptance by industry and regulatory agencies, thus accelerating their use nationwide. Each ITRD project developed at a DOE site is designed to address a typical soil or groundwater contamination issue facing both DOE and industry. This includes sites with volatile organic compound (VOC), semi-VOC, heavy metal, explosive residue, and complex or multiple constituent contamination. Projects are presently underway at three DOE facilities, while additional projects are under consideration for initiation in FY96 at several additional DOE sites. A brief overview of the ITRD Program, program plans, and the status and progress of existing ITRD projects are reviewed in this paper

Digital Technologies as Education Innovation at Universities

Science.gov (United States)

Kryukov, Vladimir; Gorin, Alexey

2017-01-01

This paper analyses the use of digital technology-based education innovations in higher education. It demonstrated that extensive implementation of digital technologies in universities is the main factor conditioning the acceleration of innovative changes in educational processes, while digital technologies themselves become one of the key…

Innovative sport technology through cross-disciplinary research ...

African Journals Online (AJOL)

Innovative sport technology through cross-disciplinary research: Future of sport ... South African Journal for Research in Sport, Physical Education and Recreation ... of the advantages and disadvantages of innovative sport technology brought ...

Launching technological innovations

DEFF Research Database (Denmark)

Talke, Katrin; Salomo, Søren

2009-01-01

have received less attention. This study considers the interdependencies between strategic, internally and externally, directed tactical launch activities and investigates both direct and indirect performance effects. The analysis is based upon data from 113 technological innovations launched...

Innovating Education and Educating for Innovation: The Power of Digital Technologies and Skills

Science.gov (United States)

OECD Publishing, 2016

2016-01-01

OECD's Innovation Strategy calls upon all sectors in the economy and society to innovate in order to foster productivity, growth and well-being. Education systems are critically important for innovation through the development of skills that nurture new ideas and technologies. However, whereas digital technologies are profoundly changing the way…

The Kyoto mechanisms and technological innovation

International Nuclear Information System (INIS)

Lund, Henrik

2006-01-01

Climate change response, including the implementation of the Kyoto targets as the first step, calls for technological innovation of future sustainable energy systems. Based on the Danish case, this paper evaluates the type of technological change necessary. During a period of 30 years, Denmark managed to stabilize primary energy supply, and CO 2 emissions decreased by 10%, during a period of 20 years. However, after the introduction of the Kyoto Mechanisms, Denmark has changed its strategy. Instead of continuing the domestic CO 2 emission controls, Denmark plans to buy CO 2 reductions in other countries. Consequently, the innovative technological development has changed. This paper evaluates the character of such change and makes preliminary recommendations for policies to encourage the use of the Kyoto Mechanisms as an acceleration of the necessary technological innovation. (author)

Innovative and Alternative Technology Assessment Manual

Energy Technology Data Exchange (ETDEWEB)

None

1980-02-01

This four chapter, six appendix manual presents the procedures and methodology as well as the baseline costs and energy information necessary for the analysis and evaluation of innovative and alternative technology applications submitted for federal grant assistance under the innovative and alternative technology provisions of the Clean Water Act of 1977. The manual clarifies and interprets the intent of Congress and the Environmental Protection Agency in carrying out the mandates of the innovative and alternative provisions of the Clean Water Act of 1977. [DJE 2005

Nonthermal physical technologies to decontaminate and extend the shelf-life of fruits and vegetables: Trends aiming at quality and safety.

Science.gov (United States)

Pinela, José; Ferreira, Isabel C F R

2017-07-03

Minimally processed fruits and vegetables are one of the major growing sectors in food industry. This growing demand for healthy and convenient foods with fresh-like properties is accompanied by concerns surrounding efficacy of the available sanitizing methods to appropriately deal with food-borne diseases. In fact, chemical sanitizers do not provide an efficient microbial reduction, besides being perceived negatively by the consumers, dangerous for human health, and harmful to the environment, and the conventional thermal treatments may negatively affect physical, nutritional, or bioactive properties of these perishable foods. For these reasons, the industry is investigating alternative nonthermal physical technologies, namely innovative packaging systems, ionizing and ultraviolet radiation, pulsed light, high-power ultrasound, cold plasma, high hydrostatic pressure, and dense phase carbon dioxide, as well as possible combinations between them or with other preservation factors (hurdles). This review discusses the potential of these novel or emerging technologies for decontamination and shelf-life extension of fresh and minimally processed fruits and vegetables. Advantages, limitations, and challenges related to its use in this sector are also highlighted.

MERCURY CONTAMINATED MATERIAL DECONTAMINATION METHODS: INVESTIGATION AND ASSESSMENT; TOPICAL

International Nuclear Information System (INIS)

M.A. Ebadian, Ph.D.

2001-01-01

Over the years mercury has been recognized as having serious impacts on human health and the environment. This recognition has led to numerous studies that deal with the properties of various mercury forms, the development of methods to quantify and speciate the forms, fate and transport, toxicology studies, and the development of site remediation and decontamination technologies. This report reviews several critical areas that will be used in developing technologies for cleaning mercury from mercury-contaminated surfaces of metals and porous materials found in many DOE facilities. The technologies used for decontamination of water and mixed wastes (solid) are specifically discussed. Many technologies that have recently appeared in the literature are included in the report. Current surface decontamination processes have been reviewed, and the limitations of these technologies for mercury decontamination are discussed. Based on the currently available technologies and the processes published recently in the literature, several processes, including strippable coatings, chemical cleaning with iodine/iodide lixiviant, chemisorbing surface wipes with forager sponge and grafted cotton, and surface/pore fixation through amalgamation or stabilization, have been identified as potential techniques for decontamination of mercury-contaminated metal and porous surfaces. Their potential merits and applicability are discussed. Finally, two processes, strippable coatings and chemical cleaning with iodine/iodide lixiviant, were experimentally investigated in Phase II of this project

Research on the Synergy Degree of China Yangtze River Delta Region Technology Innovation System Evolution from the Perspective of Technology Innovation Chain

Directory of Open Access Journals (Sweden)

Xu Bin Feng

2014-08-01

Full Text Available Abstract: This paper divides technology innovation system into research and development input subsystem, technology research and development subsystem and technology application subsystem from the perspective of technology innovation chain, combining with the system theory. Then selects the corresponding ordinal variables, makes an empirical analysis to the synergy degree of Yangtze River delta regional technology innovation system evolution by complex system synergy degree model which based on the data of 2002-2009. The results show that the development of synergy degree of the technology innovation system appears a rising trend and the technology application subsystem is the key factor of direction and degree of synergy development in the evolution process of regional technology innovation system in the Yangtze River Delta of China. Finally, this paper analyzes the characteristics and causes of synergy degree’s evolution, and puts forward the corresponding policy recommendations to different problems.

Full system decontamination feasibility studies

International Nuclear Information System (INIS)

Denault, R.P.; LeSurf, J.E.; Walschot, F.W.

1988-01-01

Many chemical decontaminations have been performed on subsystems in light water reactors (BWRs and PWRs) but none on the full system (including the fuel) of large, (>500 MWe) investor owned reactors. Full system decontaminations on pressure-tubed reactors have been shown to facilitate maintenance, inspection, repair and replacement of reactor components. Further advantages are increased reactor availability and plant life extension. A conceptual study has been performed for EPRI (for PWRs) and Commonwealth Edison Co (for BWRs) into the applicability and cost benefit of full system decontaminations (FSD). The joint study showed that FSDs in both PWRs and BWRs, with or without the fuel included in the decontamination, are feasible and cost beneficial provided a large amount of work is to be done following the decontamination. The large amounts of radioactive waste generated can be managed using current technologies. Considerable improvements in waste handling, and consequent cost savings, can be obtained if new techniques which are now reaching commercial application are used. (author)

Healthcare technology innovation adoption electronic health records and other emerging health information technology innovations

CERN Document Server

Daim, Tugrul U; Basoglu, Nuri; Kök, Orhun M; Hogaboam, Liliya

2016-01-01

This book aims to study the factors affecting the adoption and diffusion of Health Information Technology (HIT) innovation. It analyzes the adoption processes of various tools and applications, particularly Electronic Health Records (EHR), highlighting the impact on various sectors of the healthcare system, such as physicians, administration,  and patient care, while also identifying the various pitfalls and gaps in the literature. With the various challenges currently facing the United States healthcare system, the study, adoption and diffusion of healthcare technology innovation, particularly HIT, is imperative to achieving national goals. This book is organized into three sections. Section one reviews theories and applications for the diffusion of Health Care Technologies. Section two evaluates EHR technology, including the barriers and enables in adoption and alternative technologies. Finally, section three examines the factors impacting the adoption of EHR systems. This book will be a key source for stu...

Position-sensitive radiation monitoring (surface contamination monitor). Innovative technology summary report

International Nuclear Information System (INIS)

1999-06-01

The Shonka Research Associates, Inc. Position-Sensitive Radiation Monitor both detects surface radiation and prepares electronic survey map/survey report of surveyed area automatically. The electronically recorded map can be downloaded to a personal computer for review and a map/report can be generated for inclusion in work packages. Switching from beta-gamma detection to alpha detection is relatively simple and entails moving a switch position to alpha and adjusting the voltage level to an alpha detection level. No field calibration is required when switching from beta-gamma to alpha detection. The system can be used for free-release surveys because it meets the federal detection level sensitivity limits requires for surface survey instrumentation. This technology is superior to traditionally-used floor contamination monitor (FCM) and hand-held survey instrumentation because it can precisely register locations of radioactivity and accurately correlate contamination levels to specific locations. Additionally, it can collect and store continuous radiological data in database format, which can be used to produce real-time imagery as well as automated graphics of survey data. Its flexible design can accommodate a variety of detectors. The cost of the innovative technology is 13% to 57% lower than traditional methods. This technology is suited for radiological surveys of flat surfaces at US Department of Energy (DOE) nuclear facility decontamination and decommissioning (D and D) sites or similar public or commercial sites

Position-sensitive radiation monitoring (surface contamination monitor). Innovative technology summary report

Energy Technology Data Exchange (ETDEWEB)

1999-06-01

The Shonka Research Associates, Inc. Position-Sensitive Radiation Monitor both detects surface radiation and prepares electronic survey map/survey report of surveyed area automatically. The electronically recorded map can be downloaded to a personal computer for review and a map/report can be generated for inclusion in work packages. Switching from beta-gamma detection to alpha detection is relatively simple and entails moving a switch position to alpha and adjusting the voltage level to an alpha detection level. No field calibration is required when switching from beta-gamma to alpha detection. The system can be used for free-release surveys because it meets the federal detection level sensitivity limits requires for surface survey instrumentation. This technology is superior to traditionally-used floor contamination monitor (FCM) and hand-held survey instrumentation because it can precisely register locations of radioactivity and accurately correlate contamination levels to specific locations. Additionally, it can collect and store continuous radiological data in database format, which can be used to produce real-time imagery as well as automated graphics of survey data. Its flexible design can accommodate a variety of detectors. The cost of the innovative technology is 13% to 57% lower than traditional methods. This technology is suited for radiological surveys of flat surfaces at US Department of Energy (DOE) nuclear facility decontamination and decommissioning (D and D) sites or similar public or commercial sites.

European innovation and technology development

International Nuclear Information System (INIS)

Johnson, R.W.

1991-01-01

The promotion of technological innovation by European national governments and the EC in pursuit of both increased recovery and the anchoring of technology in supply, manufacturing and service sector companies has been a feature of the strategic involvement by European states in exploration and production research and development. This paper summaries past trends in this activity and reviews the targets for future industry innovation which will enable European (primarily the North Sea) production to be sustained for a further generation

RCRA permitting strategies for the development of innovative technologies: Lessons from Hanford

International Nuclear Information System (INIS)

Gajewski, S.W.; Donaghue, J.F.

1994-01-01

The Hanford Site restoration is the largest waste cleanup operation in history. The Hanford plutonium production mission generated two-thirds of all the nuclear waste, by volume, in the Department of Energy (DOE) Complex. Cleanup challenges include not only large stored volumes of radioactive, hazardous, and mixed waste, but contaminated soil and groundwater and scores of major structures slated for decontamination, decommissioning, and demolition. DOE and its contractors will need to invent the technology required to do the job on a timetable driven by negotiated milestones, public concerns, and budgetary constraints. This paper will discuss the effort at Hanford to develop an integrated, streamlined strategy for compliance with the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) in the conduct of research, development, and demonstration (RD ampersand D) of innovative cleanup technologies. The aspects that will be discussed include the following: the genesis of the RD ampersand D permitting challenge at Hanford; permitting options in the existing regulatory framework; regulatory options that offered the best fit for Hanford RD ampersand D activities, and the problems associated with them; and conclusions and recommendations made to regulatory bodies

Mobile Work Platform - A Fluor Fernald innovative dismantlement technology

International Nuclear Information System (INIS)

Peters, Mark S.; Cromer, Paul R.; Danner, Robert

2000-01-01

The Department of Energy's (DOE) Office of Science and Technology Decontamination and Decommissioning (D andD) Focus Area, led by the National Energy Technology Laboratory, has been charged with finding new and innovative D and D technologies and then validating through field demonstration that the technologies are safer, faster and/or more cost-effective. The D and D Focus Area's approach to verifying the benefits of the improved D and D technologies is to use them at DOE sites in large-scale demonstration and deployment (LSDD) projects. The DOE's Fernald Environmental Management Project (FEMP), near Cincinnati Ohio, was host for a LSDD Project overseen by the D and D Focus Area. The FEMP was formerly engaged in the production of high quality uranium metal; and is now currently undergoing active environmental restoration, including removal of major process facilities. As observed during the D and D of Fernald's Plant 1, the baseline method for removing piping required laborers to work above the floor on ladders, scaffolding, ardor man-lifts with hand-held power tools. The pipe must first be rigged to prevent falling when cut. After cutting, the pipe is manually lowered to the ground and placed in a storage/disposal container. The Mobile Work Platform (MWP) consists of a mobile chassis, telescoping arm and a dual crimper/shear ''end-effecter''. It has the capability to grab and hold a pipe, crimp and shear the pipe (up to a ten-foot section) on either side of where it is being held and then lower and place the pipe section into a storage/disposal container. The MWP can crimp/shear up to a 6-inch diameter, schedule 401, carbon steel pipe. A single operator using a radio remote control operates the MWP. The paper will describe the results (productivity, safety advantages and lessons learned) during the Mobile Work Platform demonstration at Fernald

Quantification of Technology Innovation Usinga Risk-Based Framework

OpenAIRE

Gerard E. Sleefe

2010-01-01

There is significant interest in achieving technology innovation through new product development activities. It is recognized, however, that traditional project management practices focused only on performance, cost, and schedule attributes, can often lead to risk mitigation strategies that limit new technology innovation. In this paper, a new approach is proposed for formally managing and quantifying technology innovation. This approach uses a risk-based framework that s...

Policies for the Energy Technology Innovation System (ETIS)

NARCIS (Netherlands)

Grubler, A.; Aguayo, F.; Gallagher, K.; Hekkert, M.P.; Jiang, K.; Mytelka, L.; Neij, L.; Nemet, G.; Wilson, C.

2012-01-01

Innovation and technological change are integral to the energy system transformations described in the Global Energy Assessment (GEA) pathways. Energy technology innovations range from incremental improvements to radical breakthroughs and from technologies and infrastructure to social institutions

Emerging Technological Risk Underpinning the Risk of Technology Innovation

CERN Document Server

Anderson, Stuart

2012-01-01

Classes of socio-technical hazards allow a characterization of the risk in technology innovation and clarify the mechanisms underpinning emergent technological risk. Emerging Technological Risk provides an interdisciplinary account of risk in socio-technical systems including hazards which highlight: ·         How technological risk crosses organizational boundaries, ·         How technological trajectories and evolution develop from resolving tensions emerging between social aspects of organisations and technologies and ·         How social behaviour shapes, and is shaped by, technology. Addressing an audience from a range of academic and professional backgrounds, Emerging Technological Risk is a key source for those who wish to benefit from a detail and methodical exposure to multiple perspectives on technological risk. By providing a synthesis of recent work on risk that captures the complex mechanisms that characterize the emergence of risk in technology innovation, Emerging Tec...

Understanding energy technology developments from an innovation system perspective

Energy Technology Data Exchange (ETDEWEB)

Borup, M.; Nygaard Madsen, A. [Risoe National Lab., DTU, Systems Analysis Dept., Roskilde (Denmark); Gregersen, Birgitte [Aalborg Univ., Department of Business Studies (Denmark)

2007-05-15

With the increased market-orientation and privatisation of the energy area, the perspective of innovation is becoming more and more relevant for understanding the dynamics of change and technology development in the area. A better understanding of the systemic and complex processes of innovation is needed. This paper presents an innovation systems analysis of new and emerging energy technologies in Denmark. The study focuses on five technology areas: bio fuels, hydrogen technology, wind energy, solar cells and energy-efficient end-use technologies. The main result of the analysis is that the technology areas are quite diverse in a number of innovation-relevant issues like actor set-up, institutional structure, maturity, and connections between market and non-market aspects. The paper constitutes background for discussing the framework conditions for transition to sustainable energy technologies and strengths and weaknesses of the innovation systems. (au)

Information and Innovation Management within Information Technology Enterprises

OpenAIRE

Geoff D. Skinner

2010-01-01

Australia, while being a large and eager consumer of innovative and cutting edge Information and Communication Technologies (ICT), continues to struggle to remain a leader in Technological Innovation. This paper has two main contributions to address certain aspects of this complex issue. The first being the current findings of an ongoing research project on Information and Innovation Management in the Australian Information and Communication Technologies (ICT) sector. The...

Decontamination Efficacy Testing of COTS SteriFx Prodcuts for Mass Personnel and Casualty Decontamination

Science.gov (United States)

2011-09-01

amounts of water for at least 15 min. Ingestion : If alert give several glasses of water or milk . Do not induce vomiting. Contact poison control center...strong oxidants that can harm skin and eyes. A safe, easily disseminated and effective alternative biological decontamination agent is needed to address...outlined in our preliminary work, shows that the technology has a very low risk of doing harm to personnel in decontamination scenarios, or that

Innovation in nuclear energy technology

International Nuclear Information System (INIS)

Dujardin, Th.; Bertel, E.; Kwang Seok, Lee; Foskolos, K.

2007-01-01

Innovation has been a driving force for the success of nuclear energy and remains essential for its sustainable future. Many research and development programmes focus on enhancing the performance of power plants in operation, current fuel design and characteristics, and fuel cycle processes used in existing facilities. Generally performed under the leadership of the industry. Some innovation programmes focus on evolutionary reactors and fuel cycles, derived from systems of the current generation. Such programmes aim at achieving significant improvements, in the field of economics or resource management for example, in the medium term. Often, they are undertaken by the industry with some governmental support as they require basic research together with technological development and adaptation. Finally, large programmes, often undertaken in an international, intergovernmental framework are devoted to design and development of a new generation of systems meeting the goals of sustainable development in the long term. Driving forces for nuclear innovation vary depending on the target technology, the national framework and the international context surrounding the research programme. However, all driving factors can be grouped in three categories: market drivers, political drivers and technology drivers. Globally, innovation in the nuclear energy sector is a success story but is a lengthy process that requires careful planning and adequate funding to produce successful outcomes

Innovating beyond Technology : Studies on how management innovation, co-creation and business model innovation contribute to firms' (innovation) performance

NARCIS (Netherlands)

C.V. Heij (Kevin)

2015-01-01

textabstractInnovation is generally considered to be a cornerstone of organizational survival in many of today’s dynamic and competitive markets. This dissertation goes beyond the dominant focus on technological innovation in innovation studies by examining how and under which conditions several

Problems forming innovative-technological image of russian regions

Directory of Open Access Journals (Sweden)

Irina Markovna Golova

2012-06-01

Full Text Available In this paper, actual problems of innovative-technological image as a key element of the mechanism of the healing sources of socioeconomic development of the Russian regionsare considered. The author gives an assessment of the level of differentiation of subjects of the Russian Federation on the potential for innovative development. Trends in spatial transformations of thescientific and technical and innovation capacities of the country are analyzedand reasons of low innovational activity of Russian enterprises are disclosed. Basic conditions for the success of actions to create an attractive image of innovative-technological territory are formulated. Special attention is paid to the position of regions as participants in the innovational processes, creating preconditions for creativity, harmonization of spatial priorities of innovation, technological and socio-economic development, support for the development of new high-tech industries, improvement of inter-budgetary relations. There are proved priority areas of state policy to reduce barriers to the realization of an innovative paradigm for development of Russian society and effective inclusion of local communities in the implementation of innovative changes.

A study on dry decontamination using ion exchange polymer

International Nuclear Information System (INIS)

Jung, Ki Jung; Ahn, Byung Gil

1997-12-01

Through the project of A study on dry decontamination using ion exchange polymer , the followings were investigated. 1. Highly probable decontamination technologies for the decontamination were investigated. 2. Development of gel type decontamination agent using ion-exchange resin powder (mixed type) as an ion exchanger. 3. Manufacturing of contaminated specimens (5 kinds) with Cs-137 solution and dust / Cs-137 solution. 4. Decontamination performance evaluation of the manufactured agent. 5. Analysis of composition (XRF) and the structure of surface of specimens (optic micrography). (author). 20 refs., 11 figs

Teaching biomedical technology innovation as a discipline.

Science.gov (United States)

Yock, Paul G; Brinton, Todd J; Zenios, Stefanos A

2011-07-20

Recently, universities in the United States and abroad have developed dedicated educational programs in life science technology innovation. Here, we discuss the two major streams of educational theory and practice that have informed these programs: design thinking and entrepreneurship education. We make the case that the process of innovation for new medical technologies (medtech) is different from that for biopharmaceuticals and outline the challenges and opportunities associated with developing a discipline of medtech innovation.

Game-Like Technology Innovation Education

Science.gov (United States)

Magnussen, Rikke

2011-01-01

This paper examines the methodological challenges and perspectives of designing game-like scenarios for the implementation of innovation processes in school science education. This paper presents a design-based research study of a game-like innovation scenario designed for technology education for Danish public school students aged 13-15. Students…

Environmental regulation and technological innovation

Energy Technology Data Exchange (ETDEWEB)

Farrell, A.E. [Carnegie Mellon Electricity Industry Center, Pittsburg, PA (United States)

2002-07-01

Government policies are a major factor in the determination of structural conditions of competition. The innovative activity comprises the following: invention, adoption, and diffusion. Invention involves research and development activities such as patenting, research and development budgets. The adoption phase is concerned with deployment. As for the diffusion phase, it involves commercialization, and scale-economies. The process of introducing new technologies that are adopted by small numbers of customers in a niche market was explained. Once costs are lowered through experience gained in designing, manufacturing and servicing the new technology, mew applications generally lead to larger markets. Environmental technologies have no early adopters, implying that governments have an important role to play. However, commercial processes are not normally as well known to government as it is to the private sector. The electoral cycle also interferes with long term research and development efforts for technological clusters. A look at sulphur dioxide control at United States power plants illustrated the problem. The author then explained the reasons behind low allowance prices. Low-sulphur western coal was rendered economic in large areas of the United States by rail deregulation. Electricity restructuring was also a factor. The author indicated that binding government regulation must come before adoption and diffusion of emission controls. A summary of recent research was provided, in which the author stated that no single policy instrument was likely to properly stimulate innovative activity. In those cases where both supply and demand are stimulated by government, the technological innovation is greatest. Stringent regulations induce innovation, as do greater flexibility and greater regulatory certainty. Knowledge transfer within the industry is vital. 8 refs., 3 figs.

Seeds of Innovation: Three Years of the Technology Innovation Challenge Grant Program.

Science.gov (United States)

Harris, Larry A.

This publication describes the 62 projects that received 5-year Technology Innovation Challenge Grants beginning in 1995, 1996, and 1997, with reviews of the projects occurring in late 1999 and early 2000. Part 1 of the report describes the Technology Innovation Challenge Grant (TICG) program and its importance. Part 2 contains the project…

Innovative technology demonstration

International Nuclear Information System (INIS)

Anderson, D.B.; Luttrell, S.P.; Hartley, J.N.; Hinchee, R.

1992-04-01

The Innovative Technology Demonstration (ITD) program at Tinker Air Force Base (TAFB), Oklahoma City, Oklahoma, will demonstrate the overall utility and effectiveness of innovative technologies for site characterization, monitoring, and remediation of selected contaminated test sites. The current demonstration test sites include a CERCLA site on the NPL list, located under a building (Building 3001) that houses a large active industrial complex used for rebuilding military aircraft, and a site beneath and surrounding an abandoned underground tank vault used for storage of jet fuels and solvents. The site under Building 3001 (the NW Test Site) is contaminated with TCE and Cr +6 ; the site with the fuel storage vault (the SW Tanks Site) is contaminated with fuels, BTEX and TCE. These sites and others have been identified for cleanup under the Air Force's Installation Restoration Program (IRP). This document describes the demonstrations that have been conducted or are planned for the TAFB

The Kyoto Mechanisms and Technological Innovation

DEFF Research Database (Denmark)

Lund, Henrik

2003-01-01

Climate change response, including implementation of the Kyoto targets as the first step, calls for technological innovation of future sustainable energy systems. One of the important agreements in several declarations, including the Kyoto protocol, has been to promote and coordinate...... the collaboration between the countries in the necessary technological development. The paper encourage that the Kyoto mechanisms will be used for acceleration of the necessary technical innovation in Denmark....

The development strategy of financial and innovative technologies

OpenAIRE

R.V. Lavrov

2013-01-01

The aim of the article. The aim of the article is to define and to estimate the forming of expediency of the development strategy of financial and innovative technologies in the context of modern economic space realities.The results of the analysis. The growing importance of the financial sector in the contemporary economic space, as well as rapid changes in it, generates a need for financial innovative technologies. Development strategy of financial and innovative technologies is always asso...

Indoor radiation mapping using the Laser Assisted Ranging and Data System (LARADS). Innovative technology summary report

International Nuclear Information System (INIS)

1998-11-01

The US Department of Energy's (DOE's) nuclear facilities require characterization and documentation of the results as part of planning and decision-making for decontamination and decommissioning (D and D) projects and to release areas that have been cleaned up. Conducting radiation surveys of indoor and outdoor surfaces and generating accurate survey reports is an important component of the D and D program. The Laser Assisted Ranging and Data System (LARADS) is a characterization technology that provides real-time data on the location and concentration levels of radiological contamination. The system can be utilized with a number of available detection instruments and can be integrated with existing data analysis and mapping software technologies to generate superior quality survey data reports. This innovative technology is competitive with baseline technologies in terms of cost and survey times, but is much more flexible and provides more useful reports. The system also has the capability of electronically logging survey data, making it easy to store and retrieve. Such data are scientifically derived and not subject to interpretation. The LARADS is an extremely attractive alternative to manually generated survey data reports

Large-scale decontamination and decommissioning technology demonstration project at a former uranium metal production facility

International Nuclear Information System (INIS)

Martineit, R.A.; Borgman, T.D.; Peters, M.S.; Stebbins, L.L.

1997-01-01

The Department of Energy's (DOE) Office of Science and Technology Decontamination and Decommissioning (D ampersand D) Focus Area, led by the Federal Energy Technology Center, has been charged with improving upon baseline D ampersand D technologies with the goal of demonstrating and validating more cost-effective and safer technologies to characterize, deactivate, survey, decontaminate, dismantle, and dispose of surplus structures, buildings, and their contents at DOE sites. The D ampersand D Focus Area's approach to verifying the benefits of the improved D ampersand D technologies is to use them in large-scale technology demonstration (LSTD) projects at several DOE sites. The Fernald Environmental Management Project (FEMP) was selected to host one of the first three LSTD's awarded by the D ampersand D Focus Area. The FEMP is a DOE facility near Cincinnati, Ohio, that was formerly engaged in the production of high quality uranium metal. The FEMP is a Superfund site which has completed its RUFS process and is currently undergoing environmental restoration. With the FEMP's selection to host an LSTD, the FEMP was immediately faced with some challenges. The primary challenge was that this LSTD was to be integrated into the FEMP's Plant 1 D ampersand D Project which was an ongoing D ampersand D Project for which a firm fixed price contract had been issued to the D ampersand D Contractor. Thus, interferences with the baseline D ampersand D project could have significant financial implications. Other challenges include defining and selecting meaningful technology demonstrations, finding/selecting technology providers, and integrating the technology into the baseline D ampersand D project. To date, twelve technologies have been selected, and six have been demonstrated. The technology demonstrations have yielded a high proportion of open-quotes winners.close quotes All demonstrated, technologies will be evaluated for incorporation into the FEMP's baseline D ampersand D

Innovative technologies in primary school

Directory of Open Access Journals (Sweden)

Lyzentsova L.A.

2017-01-01

Full Text Available this article describes innovative technologies during the classes in elementary school. The author has noted that the introduction of new technology promotes the development of education and the student's desire to learn and fosters independence, initiative and tolerance.

Decontamination technology of contaminated water with flocculating and settling technology

International Nuclear Information System (INIS)

Aritomi, Masanori; Adachi, Toshihiro; Watanabe, Noriyuki; Hosobuchi, Shigeki

2012-01-01

In the joint research and development of treatment systems of cooling water for cutting asphalt pavement surface with our authors' group, the liquid-solid separation technology by flocculating and settling technology, and the flocculants for the use of systems were developed. In this paper, the developed flocculating and settling technology and the flocculants are discussed first. Next, the demonstration tests of decontamination technology on the contaminated water in swimming pools in an elementary school located at Motomiya City, Fukushima Prefecture had been conducted by use of the stationary purification system of contaminated water and the flocculants compounding with or without iron ferrocianide developed by the preliminary test. It was clarified from the results that ionized cesium (Cs) rarely exists in the stagnant water in pools, ponds, lakes and so on at the time when nine months have passed since Fukushima Dai-ichi nuclear power plant accidents. Further, it is necessary to use the flocculants compounding iron ferrocianide in the case where ionized Cs exists in water. From the above-mentioned results, the following problems were pointed out: One problem was cyanide dissolution in the purified water and the other one was the dissolution from the dehydration sludge. Finally, the high-performance mobile purification units of contaminated water which is capable for carrying with trucks have been developed, and the demonstration test was performed in Minami-soma City, Fukushima Prefecture to purify the contaminated water in a pond and generated by the high-pressure water washing in a Public Hall. From the test results, it was made clear that the dehydration sludge separated by liquid-solid settling of the contaminated water of around 1,000Bq/l became a high radiation dose of about 185,000Bq/l. (author)

Technological Innovation Capabilities and Firm Performance

OpenAIRE

Richard C.M. Yam; William Lo; Esther P.Y. Tang; Antonio; K.W. Lau

2010-01-01

Technological innovation capability (TIC) is defined as a comprehensive set of characteristics of a firm that facilities and supports its technological innovation strategies. An audit to evaluate the TICs of a firm may trigger improvement in its future practices. Such an audit can be used by the firm for self assessment or third-party independent assessment to identify problems of its capability status. This paper attempts to develop such an auditing framework that can...

Technology and Innovation Management in Higher Education

DEFF Research Database (Denmark)

Morales, Antonio Adrián Arciénaga; Nielsen, Janni; Bacarini, Hernán Alberto

2018-01-01

different ways to obtain a panoply of competencies to identify technology and innovation management issues at individual business and regional level, particularly for small-and-medium-sized enterprises (SMEs). The model addresses innovation challenges related to new innovative relationships and product...

[Innovative technology and blood safety].

Science.gov (United States)

Begue, S; Morel, P; Djoudi, R

2016-11-01

If technological innovations are not enough alone to improve blood safety, their contributions for several decades in blood transfusion are major. The improvement of blood donation (new apheresis devices, RFID) or blood components (additive solutions, pathogen reduction technology, automated processing of platelets concentrates) or manufacturing process of these products (by automated processing of whole blood), all these steps where technological innovations were implemented, lead us to better traceability, more efficient processes, quality improvement of blood products and therefore increased blood safety for blood donors and patients. If we are on the threshold of a great change with the progress of pathogen reduction technology (for whole blood and red blood cells), we hope to see production of ex vivo red blood cells or platelets who are real and who open new conceptual paths on blood safety. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

CONSTRUCTION TECHNOLOGY DIFFUSION IN DEVELOPING COUNTRIES: LIMITATIONS OF PREVAILING INNOVATION SYSTEMS

Directory of Open Access Journals (Sweden)

Emilia van Egmond-deWilde de Ligny

2008-12-01

Full Text Available The diffusion of innovative technologies in the market is usually a complex and difficult process with a varying degree of success and the effects of the diffused innovative technologies are very un-balanced. The objective of our research is to gain insight into the reasons why the diffusion of innovative technology fails, even though they promise a superior performance compared to incumbent technologies. Drawing on innovation systems theories, we have identified and used the concepts of technological regime, actor network and technology sets to analyze technology diffusion in a case study in the dwelling construction industry in Costa Rica. The results showed bottlenecks in the prevailing innovation system that curtailed the diffusion of an innovative construction technology.

Testing and evaluation of electrokinetic decontamination of concrete

International Nuclear Information System (INIS)

DePaoli, D.W.; Harris, M.T.; Ally, M.R.

1996-10-01

The goals and objectives of the technical task plan (TTP) are to (1) describe the nature and extent of concrete contamination within the Department of Energy (DOE) complex and emerging and commercial technologies applicable to these problems; (2) to match technologies to the concrete problems and recommend up to four demonstrations; (3) to initiate recommended demonstrations; and (4) to continue investigation and evaluation of the application of electrokinetic decontamination processes to concrete. This document presents findings of experimental and theoretical studies of the electrokinetic decontamination (EK) process and their implications for field demonstrations. This effort is an extension of the work performed under TTP 142005, ''Electroosmotic Concrete Decontamination. The goals of this task were to determine the applicability of EK for treating contaminated concrete and, if warranted, to evaluate EK as a potential technology for demonstration. 62 refs

Solar Preheated Ventilation - Innovative Solar Technology

National Research Council Canada - National Science Library

Gaberson, Howard

1999-01-01

.... This innovative technology applies to both new construction or rehabilitation projects. This TDS introduces this low maintenance solar technology for consideration in all future industrial ventilation or HVAC projects...

The technological innovation case of the KAERI

Energy Technology Data Exchange (ETDEWEB)

Choi, J. I. [Habat Univ., Daejeon (Korea, Republic of); Jang, S. K. [Sungkonghoe Univ., Seoul (Korea, Republic of); Hong, K. P. [Baekseok Univ., Chunan (Korea, Republic of); Lee, E. S. [National Fusion Research Institue, Daejeon (Korea, Republic of)

2008-01-15

The research aims to investigate what key success factors (KSFs) of technological innovation in KAERI are, and to suggest how these findings are utilized for KAERI. In order to achieve these goals we have employed case study based on in-depth interview and literature review. And there are two fields of research in KAERI: one is nuclear energy-related research, the other is non energy-related research. The former is 'nuclear fuel cladding tube' which is an industrial product and being regarded as catch-up (or imitative) mode of technological innovation: the latter is 'HemoHIM', herbal composition of health functional food, which is consumer goods and regarded as creative (or innovative) mode of technological innovation. We found some KSFs in these two research and development cases in KAERI: firstly, to train researcher to be a 'product champion' who can fill in the gap of 'death valley' between pure research and commercialization: secondly, to build researchers' competency in order to catch up advanced countries' technological competencies. Thirdly, to amend institutional rules and regulations for commercializing processes of R and D outcomes, notably 'R and D joint venture by Government Research Institute (GRI) and private sector' fourthly, to enhance the capabilities of external management for researchers' technological innovation competency. And finally, we recommend using successful R and D cases as educational materials when training young researchers for sharing old generations' experiences and tacit knowledge.

The technological innovation case of the KAERI

International Nuclear Information System (INIS)

Choi, J. I.; Jang, S. K.; Hong, K. P.; Lee, E. S.

2008-01-01

The research aims to investigate what key success factors (KSFs) of technological innovation in KAERI are, and to suggest how these findings are utilized for KAERI. In order to achieve these goals we have employed case study based on in-depth interview and literature review. And there are two fields of research in KAERI: one is nuclear energy-related research, the other is non energy-related research. The former is 'nuclear fuel cladding tube' which is an industrial product and being regarded as catch-up (or imitative) mode of technological innovation: the latter is 'HemoHIM', herbal composition of health functional food, which is consumer goods and regarded as creative (or innovative) mode of technological innovation. We found some KSFs in these two research and development cases in KAERI: firstly, to train researcher to be a 'product champion' who can fill in the gap of 'death valley' between pure research and commercialization: secondly, to build researchers' competency in order to catch up advanced countries' technological competencies. Thirdly, to amend institutional rules and regulations for commercializing processes of R and D outcomes, notably 'R and D joint venture by Government Research Institute (GRI) and private sector' fourthly, to enhance the capabilities of external management for researchers' technological innovation competency. And finally, we recommend using successful R and D cases as educational materials when training young researchers for sharing old generations' experiences and tacit knowledge

Technology for Innovation in Radiation Oncology

Energy Technology Data Exchange (ETDEWEB)

Chetty, Indrin J. [Department of Radiation Oncology, Henry Ford Hospital, Detroit, Michigan (United States); Martel, Mary K., E-mail: mmartel@mdanderson.org [Department of Radiation Physics, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Jaffray, David A. [Departments of Radiation Oncology and Medical Biophysics, Princess Margaret Hospital, Toronto, Ontario (Canada); Benedict, Stanley H. [Department of Radiation Oncology, University of California – Davis Cancer Center, Sacramento, California (United States); Hahn, Stephen M. [Department of Radiation Oncology, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Berbeco, Ross [Department of Radiation Oncology, Brigham and Women' s Hospital, Boston, Massachusetts (United States); Deye, James [Radiation Research Programs, National Cancer Institute, Bethesda, Maryland (United States); Jeraj, Robert [Department of Medical Physics, University of Wisconsin, Madison, Wisconsin (United States); Kavanagh, Brian [Department of Radiation Oncology, University of Colorado, Aurora, Colorado (United States); Krishnan, Sunil [Department of Radiation Oncology, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Lee, Nancy [Department of Radiation Oncology, Memorial Sloan Kettering Cancer Center, New York, New York (United States); Low, Daniel A. [Department of Radiation Oncology, University of California – Los Angeles, Los Angeles, California (United States); Mankoff, David [Department of Radiology, University of Washington Medical School, Seattle, Washington (United States); Marks, Lawrence B. [Department of Radiation Oncology, University of North Carolina Hospitals, Chapel Hill, North Carolina (United States); Ollendorf, Daniel [Institute for Clinical and Economic Review, Boston, Massachusetts (United States); and others

2015-11-01

Radiation therapy is an effective, personalized cancer treatment that has benefited from technological advances associated with the growing ability to identify and target tumors with accuracy and precision. Given that these advances have played a central role in the success of radiation therapy as a major component of comprehensive cancer care, the American Society for Radiation Oncology (ASTRO), the American Association of Physicists in Medicine (AAPM), and the National Cancer Institute (NCI) sponsored a workshop entitled “Technology for Innovation in Radiation Oncology,” which took place at the National Institutes of Health (NIH) in Bethesda, Maryland, on June 13 and 14, 2013. The purpose of this workshop was to discuss emerging technology for the field and to recognize areas for greater research investment. Expert clinicians and scientists discussed innovative technology in radiation oncology, in particular as to how these technologies are being developed and translated to clinical practice in the face of current and future challenges and opportunities. Technologies encompassed topics in functional imaging, treatment devices, nanotechnology, and information technology. The technical, quality, and safety performance of these technologies were also considered. A major theme of the workshop was the growing importance of innovation in the domain of process automation and oncology informatics. The technologically advanced nature of radiation therapy treatments predisposes radiation oncology research teams to take on informatics research initiatives. In addition, the discussion on technology development was balanced with a parallel conversation regarding the need for evidence of efficacy and effectiveness. The linkage between the need for evidence and the efforts in informatics research was clearly identified as synergistic.

Technology for Innovation in Radiation Oncology

International Nuclear Information System (INIS)

Chetty, Indrin J.; Martel, Mary K.; Jaffray, David A.; Benedict, Stanley H.; Hahn, Stephen M.; Berbeco, Ross; Deye, James; Jeraj, Robert; Kavanagh, Brian; Krishnan, Sunil; Lee, Nancy; Low, Daniel A.; Mankoff, David; Marks, Lawrence B.; Ollendorf, Daniel

2015-01-01

Radiation therapy is an effective, personalized cancer treatment that has benefited from technological advances associated with the growing ability to identify and target tumors with accuracy and precision. Given that these advances have played a central role in the success of radiation therapy as a major component of comprehensive cancer care, the American Society for Radiation Oncology (ASTRO), the American Association of Physicists in Medicine (AAPM), and the National Cancer Institute (NCI) sponsored a workshop entitled “Technology for Innovation in Radiation Oncology,” which took place at the National Institutes of Health (NIH) in Bethesda, Maryland, on June 13 and 14, 2013. The purpose of this workshop was to discuss emerging technology for the field and to recognize areas for greater research investment. Expert clinicians and scientists discussed innovative technology in radiation oncology, in particular as to how these technologies are being developed and translated to clinical practice in the face of current and future challenges and opportunities. Technologies encompassed topics in functional imaging, treatment devices, nanotechnology, and information technology. The technical, quality, and safety performance of these technologies were also considered. A major theme of the workshop was the growing importance of innovation in the domain of process automation and oncology informatics. The technologically advanced nature of radiation therapy treatments predisposes radiation oncology research teams to take on informatics research initiatives. In addition, the discussion on technology development was balanced with a parallel conversation regarding the need for evidence of efficacy and effectiveness. The linkage between the need for evidence and the efforts in informatics research was clearly identified as synergistic.

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.W.

1993-01-01

Lead used for shielding is often surface contaminated with radionuclides and is therefore a Resource Conservation and Recovery Act (RCRA) D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Lab. decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 100 metric tons and likely to grow substantially because of planned decommissioning operations. This lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for decontaminating lead is removing the thin superficial layer of contamination with an abrasive medium under pressure. For lead, a mixture of alumina with water and air at about 280 kPa (40 psig) rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a sealed-off area. The slurry of abrasive and particles of lead falls through a floor grating and is collected in a pump. A pump sends the slurry mixture back to the spray gun, creating a continuous process

Towards a synergic innovation management model: the interplay of market, technology, and management innovations

Directory of Open Access Journals (Sweden)

Leonard Tchuta

2017-03-01

Full Text Available This paper outlines a model of firm innovation management known as the synergic innovation management model. Building on the theory of dynamic capabilities and core competence, the paper suggest three capabilities of firms namely market, technology, management capabilities that drive firms’ innovations. The combination of these three capabilities creates a unique configuration for a firm known as the firm’s core competence that informs the firm's strategic decisions. The synergic innovation management model guides firm in the simultaneous exploration of market, technology, and management innovations required for sustainable business. The paper concludes with limitations of the model and suggestions for further research.

Technological innovations: from bench to bedside.

Science.gov (United States)

Robert, Glenn

2009-09-01

The NHS is perceived to be slower than other healthcare systems in adopting innovative technologies that can deliver patient benefits. This article summarises what is known about the role of nurses in assimilating such innovations into clinical care, and outlines the challenges facing nurse leaders.

Global Health Innovation Technology Models

Directory of Open Access Journals (Sweden)

Kimberly Harding

2016-04-01

Full Text Available Chronic technology and business process disparities between High Income, Low Middle Income and Low Income (HIC, LMIC, LIC research collaborators directly prevent the growth of sustainable Global Health innova‐ tion for infectious and rare diseases. There is a need for an Open Source-Open Science Architecture Framework to bridge this divide. We are proposing such a framework for consideration by the Global Health community, by utiliz‐ ing a hybrid approach of integrating agnostic Open Source technology and healthcare interoperability standards and Total Quality Management principles. We will validate this architecture framework through our programme called Project Orchid. Project Orchid is a conceptual Clinical Intelligence Exchange and Virtual Innovation platform utilizing this approach to support clinical innovation efforts for multi-national collaboration that can be locally sustainable for LIC and LMIC research cohorts. The goal is to enable LIC and LMIC research organizations to acceler‐ ate their clinical trial process maturity in the field of drug discovery, population health innovation initiatives and public domain knowledge networks. When sponsored, this concept will be tested by 12 confirmed clinical research and public health organizations in six countries. The potential impact of this platform is reduced drug discovery and public health innovation lag time and improved clinical trial interventions, due to reliable clinical intelligence and bio-surveillance across all phases of the clinical innovation process.

System decontamination as a tool to control radiation fields

Energy Technology Data Exchange (ETDEWEB)

Riess, R.; Bertholdt, H.O. [Siemens Power Generation Group, Erlangen (Germany)

1995-03-01

Since chemical decontamination of the Reactor Coolant Systems (RCS) and subsystems has the highest potential to reduce radiation fields in a short term this technology has gained an increasing importance. The available decontamination process at Siemens, i.e., the CORD processes, will be described. It is characterized by using permanganic acid for preoxidation and diluted organic acid for the decontamination step. It is a regenerative process resulting in very low waste volumes. This technology has been used frequently in Europe and Japan in both RCS and subsystems. An overview will be given i.e. on the 1993 applications. This overview will include plant, scope, date of performance, system volume specal features of the process removed activities, decon factor time, waste volumes, and personnel dose during decontamination. This overview will be followed by an outlook on future developments in this area.

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.W.

1993-01-01

Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially because of planned decommissioning operations. This lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for decontaminating lead is removing the thin superficial layer of contamination with an abrasive medium trader pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a sealed-off area. The slurry of abrasive and particles of lead falls through a floor grating and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of contaminated lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling

GENERAL ENVIRONMENTAL CORPORATION; CURE ELECTROCOAGULATION TECHNOLOGY: INNOVATIVE TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

The CURE electrocoagulation technology was demonstrated under the Superfund Innovative Technology Evaluation (SITE) program at the U.S. Department of Energy (DOE) Rocky Flats Environmental Technology Site (RFETS), where water from the solar evaporation ponds (SEPs) was contaminat...

Soil decontamination criteria report, November 1980

International Nuclear Information System (INIS)

Riordan, G.A.

1980-01-01

A program to access the extent of transuranic soil contamination at DOE sites and to develop methods for their decontamination is underway at Rocky Flats. As part of this program, acceptable soil contamination levels for plutonium proposed by a number of authorities over the past couple of decades were reviewed. From this review, goals for soil decontamination work are proposed. These goals, which relate to the disposition of the products of a decontamination process, are summarized as follows (dpm/g will refer to disintegrations per minute of transuranic nuclides per gram of soil): soil fractions having less than 30 dpm can be disposed of as surface soil with unrestricted usage. Fine soil fractions (less than 100 μm) that have less than 500 dpm and coarse soil fractions that have less than 1000 dpm can be disposed of as subsurface soil as long as usage is controlled to ensure compliance with EPA dosage guidance. Soil concentrates that have an activity greater than the above values but less than 22,000 dpm should be interred in an approved, low level waste burial site. Soil concentrates that are greater than 22,000 dpm should be stored as retrievable waste. Changes in the technical and legal areas of soil decontamination are rapid. Permissible soil decontamination levels will change as will decontamination technology and the ability to monitor the effectiveness of the decontamination processes. As a result, annual updates of decontamination criteria, goals, and monitoring are expected

Measuring Consumer Innovativeness: Identifying Innovators among Consumers of Modern Technologies

Directory of Open Access Journals (Sweden)

Jana Filová

2015-12-01

Full Text Available The methods currently used in innovation marketing research are focused on the late phases of the innovation process and are usually methodologically complex. This limits their practical impact. The presented work aims to create a simple self-report scale applicable in the initial and late phases of the innovation process, highly modular and suitable for a wide range of research. The main battery of questions was inspired by the adopter categorization by Rogers. The questions determine both (1 general characteristics of innovation adopters and (2 their relationship to a specific innovation. The scale was tested during robust longitudinal online research, thematically focused on users of modern technologies. A representative sample of 4,000 Internet users in the Czech Republic took part in the survey from 2013 to 2015. The result is a new self-report scale measuring consumer innovativeness applicable for prototyping, strategic decisions and effective communication of innovations to consumers.

Exploratory Use of Microaerosol Decontamination Technology (PAEROSOL) in Enclosed, Unoccupied Hospital Setting

Energy Technology Data Exchange (ETDEWEB)

Rainina, Evguenia I.; McCune, D. E.; Luna, Maria L.; Cook, J. E.; Soltis, Michele A.; Demons, Samandra T.; Godoy-Kain, Patricia; Weston, J. H.

2012-05-31

The goal of this study was to validate the previously observed high biological kill performance of PAEROSOL, a semi-dry, micro-aerosol decontamination technology, against common HAI in a non-human subject trial within a hospital setting of Madigan Army Medical Center (MAMC) on Joint Base Lewis-McChord in Tacoma, Washington. In addition to validating the disinfecting efficacy of PAEROSOL, the objectives of the trial included a demonstration of PAEROSOL environmental safety, (i.e., impact to hospital interior materials and electronic equipment exposed during testing) and PAEROSOL parameters optimization for future deployment.

Technological Innovation and Strategic Human Resource Management: Developing a Theory.

Science.gov (United States)

Gattiker, Urs E.

Technological innovation affects the structure and content of jobs. Research indicates that there is a need for a theory of technological innovation and strategic human resource management considering several factors, such as an employee's beliefs about the effect of technological innovations on the quality of work life and work content.…

Does Your Department Have a Technology Innovation Strategy?

Science.gov (United States)

Felkey, Bill G; Fox, Brent I

2016-11-01

There are ways to facilitate the successful implementation of technological innovations. These are especially important in a time of rapid development of new tools to support safe and effective medication therapy. This installment addresses some of the key components of a successful technology innovation strategy.

Engineering innovation in healthcare: technology, ethics and persons.

Science.gov (United States)

Bowen, W Richard

2011-01-01

Engineering makes profound contributions to our health. Many of these contributions benefit whole populations, such as clean water and sewage treatment, buildings, dependable sources of energy, efficient harvesting and storage of food, and pharmaceutical manufacture. Thus, ethical assessment of these and other engineering activities has often emphasized benefits to communities. This is in contrast to medical ethics, which has tended to emphasize the individual patient affected by a doctor's actions. However technological innovation is leading to an entanglement of the activities, and hence ethical responsibilities, of healthcare professionals and engineering professionals. The article outlines three categories of innovation: assistive technologies, telehealthcare and quasi-autonomous systems. Approaches to engineering ethics are described and applied to these innovations. Such innovations raise a number of ethical opportunities and challenges, especially as the complexity of the technology increases. In particular the design and operation of the technologies require engineers to seek closer involvement with the persons benefiting from their work. Future innovation will require engineers to have a good knowledge of human biology and psychology. More particularly, healthcare engineers will need to prioritize each person's wellbeing, agency, human relationships and ecological self rather than technology, in the same way that doctors prioritize the treatment of persons rather than their diseases.

Science, Technology, and Innovation Policy

DEFF Research Database (Denmark)

Lundvall, Bengt-Åke; Borrás, Susana

2005-01-01

This chapter is about what governments have done and could do to promote the production, diffusion, and use of scientific and technical knowledge in order to realize national objectives. We begin the chapter with "story-telling" based on sketchy historical facts. The aim of  the two stories...... is to illustrate that innovation policy covers a wide set of issues that have been on the agenda far back in history while still remaining important today. We move on to sketch the history of innovation policy, splitting it up into the three ideal types: science, technology, and innovation policy. We use OECD...

Radioactive decontamination

International Nuclear Information System (INIS)

1983-07-01

This Code of Practice covers: (a) the decontamination of plant items, buildings and associated equipment; (b) decontamination of protective clothing; (c) simple personal decontamination; and (d) the basic mechanisms of contamination and their influence on decontaminability. (author)

Comparing the innovation effects of support schemes for renewable electricity technologies: A function of innovation approach

International Nuclear Information System (INIS)

Río, Pablo del; Bleda, Mercedes

2012-01-01

The aim of this paper is to provide a comparative assessment of the innovation effects of instruments which support the diffusion of renewable electricity technologies with a functions-oriented technological innovation system perspective. The paper provides a link between two major streams of the literature: the functions of innovation systems and the literature on renewable electricity support schemes. We show that, when a functional perspective is adopted, feed-in tariffs are likely to be superior to other policy instruments (quotas with tradable green certificates and tendering), although they still need to be complemented with other instruments, most importantly, direct R and D support. Furthermore, those innovation effects are affected by the specific design elements of the instruments chosen. - Highlights: ► A comparison of the innovation effects of instruments for the diffusion of renewable technologies. ► A functions-oriented technological innovation system perspective. ► A link between the functions of innovation systems and the literature on renewable electricity support schemes. ► Feed-in tariffs are likely to be superior to other instruments. ► Innovation effects are affected by the specific design elements of instruments.

Criteria and evaluation of three decontamination techniques

Energy Technology Data Exchange (ETDEWEB)

Tripp, J.L.

1994-01-01

Past decontamination and solvent recovery activities at the Idaho Chemical Processing Plant (ICPP), which is part of the Idaho National Engineering Laboratory (INEL), have resulted in the accumulation of 1.5 million gallons of radioactively contaminated sodium-bearing liquid waste. Future decontamination activities at the ICPP could result in the production of 5 million gallons or more of sodium-bearing waste using the current decontamination techniques of chemical/water flushes and steam jet cleaning. This waste requires a large amount of cold chemical additive to process because the low melting temperatures of sodium and potassium salts cause agglomeration in the bed of the calciner vessel. Criteria have been established for evaluating methods and technologies available for decontaminating equipment and facilities. The criteria were weighted according to their relative importance using a Kepner-Tregoe Problem Solving process. These criteria were used to rank three decontamination techniques new to the ICPP: laser ablation, liquid abrasive blasting and CO{sub 2} pellet blasting, against the standard decontamination techniques of sodium-based chemical cleaning and water/steam jets used.

Criteria and evaluation of three decontamination techniques

International Nuclear Information System (INIS)

Tripp, J.L.

1994-01-01

Past decontamination and solvent recovery activities at the Idaho Chemical Processing Plant (ICPP), which is part of the Idaho National Engineering Laboratory (INEL), have resulted in the accumulation of 1.5 million gallons of radioactively contaminated sodium-bearing liquid waste. Future decontamination activities at the ICPP could result in the production of 5 million gallons or more of sodium-bearing waste using the current decontamination techniques of chemical/water flushes and steam jet cleaning. This waste requires a large amount of cold chemical additive to process because the low melting temperatures of sodium and potassium salts cause agglomeration in the bed of the calciner vessel. Criteria have been established for evaluating methods and technologies available for decontaminating equipment and facilities. The criteria were weighted according to their relative importance using a Kepner-Tregoe Problem Solving process. These criteria were used to rank three decontamination techniques new to the ICPP: laser ablation, liquid abrasive blasting and CO 2 pellet blasting, against the standard decontamination techniques of sodium-based chemical cleaning and water/steam jets used

Equipment decontamination: A brief survey of the DOE complex

International Nuclear Information System (INIS)

Conner, C.; Chamberlain, D.B.; Chen, L.; Vandegrift, G.F.

1995-03-01

Deactivation at DOE facilities has left a tremendous amount of contaminated equipment behind. In-situ methods are needed to decontaminate the interiors of the equipment sufficiently to allow either free release or land disposal. A brief survey was completed of the DOE complex on their needs for equipment decontamination with in-situ technology to determine (1) the types of contamination problems within the DOE complex, (2) decontamination processes that are being used or are being developed within the DOE, and (3) the methods that are available to dispose of spent decontamination solutions. In addition, potential sites for testing decontamination methods were located. Based on the information obtained from these surveys, the Rocky Flats Plant and the Idaho National Engineering Laboratory appear to be best suited to complete the initial testing of the decontamination processes

Technology for Innovation in Radiation Oncology.

Science.gov (United States)

Chetty, Indrin J; Martel, Mary K; Jaffray, David A; Benedict, Stanley H; Hahn, Stephen M; Berbeco, Ross; Deye, James; Jeraj, Robert; Kavanagh, Brian; Krishnan, Sunil; Lee, Nancy; Low, Daniel A; Mankoff, David; Marks, Lawrence B; Ollendorf, Daniel; Paganetti, Harald; Ross, Brian; Siochi, Ramon Alfredo C; Timmerman, Robert D; Wong, John W

2015-11-01

Radiation therapy is an effective, personalized cancer treatment that has benefited from technological advances associated with the growing ability to identify and target tumors with accuracy and precision. Given that these advances have played a central role in the success of radiation therapy as a major component of comprehensive cancer care, the American Society for Radiation Oncology (ASTRO), the American Association of Physicists in Medicine (AAPM), and the National Cancer Institute (NCI) sponsored a workshop entitled "Technology for Innovation in Radiation Oncology," which took place at the National Institutes of Health (NIH) in Bethesda, Maryland, on June 13 and 14, 2013. The purpose of this workshop was to discuss emerging technology for the field and to recognize areas for greater research investment. Expert clinicians and scientists discussed innovative technology in radiation oncology, in particular as to how these technologies are being developed and translated to clinical practice in the face of current and future challenges and opportunities. Technologies encompassed topics in functional imaging, treatment devices, nanotechnology, and information technology. The technical, quality, and safety performance of these technologies were also considered. A major theme of the workshop was the growing importance of innovation in the domain of process automation and oncology informatics. The technologically advanced nature of radiation therapy treatments predisposes radiation oncology research teams to take on informatics research initiatives. In addition, the discussion on technology development was balanced with a parallel conversation regarding the need for evidence of efficacy and effectiveness. The linkage between the need for evidence and the efforts in informatics research was clearly identified as synergistic. Copyright © 2015 Elsevier Inc. All rights reserved.

Open Innovation and Technology Maturity Analysis

Science.gov (United States)

2007-09-11

INFOLOGIC Inc. All rights reserved. Innovation Management Model  Product: Technology-heavy (e.g: Airplane, iPod) OR Service-heavy (e.g: Starbucks ...System, eBay)  Process: Any critical business process to ensure the success of product (e.g: iTune for iPod, Marketing and Supply Chain Management...Integration and Voice of the Customer Voice of the Customer Integration M A T U R I T Y VALUE Radical Innovation Evolutionary Innovation INCREMENTAL

Mobile Work Platform - A Fluor Fernald innovative dismantlement technology

Energy Technology Data Exchange (ETDEWEB)

Mark S. Peters; Paul R. Cromer; Robert Danner

2000-06-16

The Department of Energy's (DOE) Office of Science and Technology Decontamination and Decommissioning (D&D) Focus Area, led by the National Energy Technology Laboratory, has been charged with finding new and innovative D&D technologies and then validating through field demonstration that the technologies are safer, faster and/or more cost-effective. The D&D Focus Area's approach to verifying the benefits of the improved D&D technologies is to use them at DOE sites in large-scale demonstration and deployment (LSDD) projects. The DOE's Fernald Environmental Management Project (FEMP), near Cincinnati Ohio, was host for a LSDD Project overseen by the D&D Focus Area. The FEMP was formerly engaged in the production of high quality uranium metal; and is now currently undergoing active environmental restoration, including removal of major process facilities. As observed during the D&D of Fernald's Plant 1, the baseline method for removing piping required laborers to work above the floor on ladders, scaffolding, ardor man-lifts with hand-held power tools. The pipe must first be rigged to prevent falling when cut. After cutting, the pipe is manually lowered to the ground and placed in a storage/disposal container. The Mobile Work Platform (MWP) consists of a mobile chassis, telescoping arm and a dual crimper/shear ''end-effecter''. It has the capability to grab and hold a pipe, crimp and shear the pipe (up to a ten-foot section) on either side of where it is being held and then lower and place the pipe section into a storage/disposal container. The MWP can crimp/shear up to a 6-inch diameter, schedule 401, carbon steel pipe. A single operator using a radio remote control operates the MWP. The paper will describe the results (productivity, safety advantages and lessons learned) during the Mobile Work Platform demonstration at Fernald.

Evaluation of six decontamination processes on actinide and fission product contamination

International Nuclear Information System (INIS)

Conner, C.; Chamberlain, D.B.; Chen, L.

1995-01-01

In-situ decontamination technologies were evaluated for their ability to: (1) reduce equipment contamination levels to allow either free release of the equipment or land disposal, (2) minimize residues generated by decontamination, and (3) generate residues that are compatible with existing disposal technologies. Six decontamination processes were selected. tested and compared to 4M nitric acid, a traditional decontamination agent: fluoroboric acid (HBF 4 ), nitric plus hydrofluoric acid, alkaline persulfate followed by citric acid plus oxalic acid, silver(II) plus sodium persulfate plus nitric acid, oxalic acid plus hydrogen peroxide plus hydrofluoric acid, and electropolishing using nitric acid electrolyte. The effectiveness of these solutions was tested using prepared 304 stainless steel couponds contaminated with uranium, plutonium, americium, or fission products. The decontamination factor for each of the solutions and tests conditions were determined; the results of these experiments are presented

Innovation Environment in Small Technology-Based Companies

OpenAIRE

Gonçalves Silveira Fiates, Gabriela; Azevedo Fiates, José Eduardo; Ribeiro Serra, Fernando A; Portugal Ferreira, Manuel

2010-01-01

Innovation has been identified as a strategy to achieve competitive advantage, particularly in contexts of change and especially for technology-based companies – TBCs. Although the adoption of innovation strategies is not easy, small companies have an organizational environment more conducive to innovation. This article examines how managers and employees of small TBCs perceive aspects of the internal environment of innovation in the organization (culture, organizational structure, personnel ...

The Opportunities and Challenges of Persuasive Technology in Creating Sustainable Innovation and Business Model Innovation

DEFF Research Database (Denmark)

Aagaard, Annabeth; Lindgren, Peter

2015-01-01

The opportunities of persuasive technology in facilitating sustainable innovation and business model innovation have been witnessed continuously during the last decade. The unique ability of persuasive technology in interacting and mediating across users, customers, decisions makers and other...... stakeholders provides access to core knowledge about behavior and opportunities to influence and even change their behavior in a positive and more sustainable manner. Sustainable innovation and business model innovation is gaining more and more competitive leverage due to customer requirements, the growing...

[Medical doctors driving technological innovation: questions about and innovation management approaches to incentive structures for lead users].

Science.gov (United States)

Bohnet-Joschko, Sabine; Kientzler, Fionn

2010-01-01

Management science defines user-generated innovations as open innovation and lead user innovation. The medical technology industry finds user-generated innovations profitable and even indispensable. Innovative medical doctors as lead users need medical technology innovations in order to improve patient care. Their motivation to innovate is mostly intrinsic. But innovations may also involve extrinsic motivators such as gain in reputation or monetary incentives. Medical doctors' innovative activities often take place in hospitals and are thus embedded into the hospital's organisational setting. Hospitals find it difficult to gain short-term profits from in-house generated innovations and sometimes hesitate to support them. Strategic investment in medical doctors' innovative activities may be profitable for hospitals in the long run if innovations provide first-mover competitive advantages. Industry co-operations with innovative medical doctors offer chances but also bear potential risks. Innovative ideas generated by expert users may result in even higher complexity of medical devices; this could cause mistakes when applied by less specialised users and thus affect patient safety. Innovations that yield benefits for patients, medical doctors, hospitals and the medical technology industry can be advanced by offering adequate support for knowledge transfer and co-operation models.

Large-Scale Urban Decontamination; Developments, Historical Examples and Lessons Learned

Energy Technology Data Exchange (ETDEWEB)

Rick Demmer

2007-02-01

Recent terrorist threats and actual events have lead to a renewed interest in the technical field of large scale, urban environment decontamination. One of the driving forces for this interest is the real potential for the cleanup and removal of radioactive dispersal device (RDD or “dirty bomb”) residues. In response the U. S. Government has spent many millions of dollars investigating RDD contamination and novel decontamination methodologies. Interest in chemical and biological (CB) cleanup has also peaked with the threat of terrorist action like the anthrax attack at the Hart Senate Office Building and with catastrophic natural events such as Hurricane Katrina. The efficiency of cleanup response will be improved with these new developments and a better understanding of the “old reliable” methodologies. Perhaps the most interesting area of investigation for large area decontamination is that of the RDD. While primarily an economic and psychological weapon, the need to cleanup and return valuable or culturally significant resources to the public is nonetheless valid. Several private companies, universities and National Laboratories are currently developing novel RDD cleanup technologies. Because of its longstanding association with radioactive facilities, the U. S. Department of Energy National Laboratories are at the forefront in developing and testing new RDD decontamination methods. However, such cleanup technologies are likely to be fairly task specific; while many different contamination mechanisms, substrate and environmental conditions will make actual application more complicated. Some major efforts have also been made to model potential contamination, to evaluate both old and new decontamination techniques and to assess their readiness for use. Non-radioactive, CB threats each have unique decontamination challenges and recent events have provided some examples. The U. S. Environmental Protection Agency (EPA), as lead agency for these emergency

Work and technological innovation in organic agriculture.

Science.gov (United States)

Tereso, M J A; Abrahão, R F; Gemma, S F B; Montedo, U B; Menegon, N L; Guarneti, J E; Ribeiro, I A V

2012-01-01

Organic agriculture is a sustainable cultivation ecologically, economically and socially. Several researches in organic agriculture have been made from technical perspectives, economic traits or related to ecological aspects. There are practically no investigations into the nature of the technology used in organic agriculture, especially from an ergonomic perspective. From the activity analysis, this study aimed to map the technology used in the production of organic vegetables. Properties producing organic vegetables were selected representing the State of São Paulo. It was applied an instrument (questionnaire and semi-structured interview) with their managers and it was made visual records to identify adaptations, innovations and technological demands that simultaneously minimize the workload and the difficulties in performing the tasks and increase work productivity. For some of the technological innovations a digital scanner was used to generate a virtual solid model to facilitate its redesign and virtual prototyping. The main results show that organic farmers have little technology in product form. The main innovations that enable competitive advantage or allow higher labor productivity occur in the form of processes, organization and marketing.

The role of innovative remediation technologies

International Nuclear Information System (INIS)

Doesburg, J.M.

1992-05-01

There are currently over 1200 sites on the US Superfund's National Priorities List (NPL) of hazardous waste sites, and there are over 30, 000 sites listed by the Comprehensive Environmental Responsibility, Compensation and Liability Information System (CERCLIS). The traditional approach to remediating sites in the US has been to remove the material and place it in a secure landfill, or in the case of groundwater, pump and treat the effluent. These technologies have proven to be very expensive and don't really fix the problem. The waste is just moved from one place to another. In recent years, however, alternative and innovative technologies have been increasingly used in the US to replace the traditional approaches. This paper will focus on just such innovative remediation technologies in the US, looking at the regulatory drivers, the emerging technologies, some of the problems in deploying technologies, and a case study

Technological innovation in neurosurgery: a quantitative study.

Science.gov (United States)

Marcus, Hani J; Hughes-Hallett, Archie; Kwasnicki, Richard M; Darzi, Ara; Yang, Guang-Zhong; Nandi, Dipankar

2015-07-01

Technological innovation within health care may be defined as the introduction of a new technology that initiates a change in clinical practice. Neurosurgery is a particularly technology-intensive surgical discipline, and new technologies have preceded many of the major advances in operative neurosurgical techniques. The aim of the present study was to quantitatively evaluate technological innovation in neurosurgery using patents and peer-reviewed publications as metrics of technology development and clinical translation, respectively. The authors searched a patent database for articles published between 1960 and 2010 using the Boolean search term "neurosurgeon OR neurosurgical OR neurosurgery." The top 50 performing patent codes were then grouped into technology clusters. Patent and publication growth curves were then generated for these technology clusters. A top-performing technology cluster was then selected as an exemplar for a more detailed analysis of individual patents. In all, 11,672 patents and 208,203 publications related to neurosurgery were identified. The top-performing technology clusters during these 50 years were image-guidance devices, clinical neurophysiology devices, neuromodulation devices, operating microscopes, and endoscopes. In relation to image-guidance and neuromodulation devices, the authors found a highly correlated rapid rise in the numbers of patents and publications, which suggests that these are areas of technology expansion. An in-depth analysis of neuromodulation-device patents revealed that the majority of well-performing patents were related to deep brain stimulation. Patent and publication data may be used to quantitatively evaluate technological innovation in neurosurgery.

A scaffold easy to decontaminate

International Nuclear Information System (INIS)

Mourek, D.

1992-01-01

The conventional scaffold used in the assembling work and in revisions of technological facilities at nuclear power plants has many drawbacks. The most serious of them are a high amount of radioactive waste arising from the decontamination (planing) of the floor timber and from the discarding of damaged irreparable parts, and a considerable corrosion of the carbon steel supporting structure after the decontamination. A detailed description is given of a novel scaffold assembly which can be decontaminated and which exhibits many assets, in particular a good mechanical resistance (also to bad weather), a lower weight, and the use of prepreg floor girders for the construction of service platforms or scaffold bridges which can readily be assembled from the pressed pieces in a modular way. (Z.S.). 4 figs., 4 refs

User driven innovation in mobile technologies?

DEFF Research Database (Denmark)

Larsen, Casper Schultz; Koch, Christian

2007-01-01

by systems already in function. Stories of prior business successes can be an important tool to ensure further innovative investments since lack of enterprise strategies is often an obstacle for innovation, especially user driven. Both small and large software houses develops dedicated software for coupling...... technology systems relying on the concept of affordance. This paper examines how innovation processes mediate between user orientations and technology offers. There is a great potential for mobile handheld ICT-systems to support numerous work processes in the AEC-industry and this can be substantiated...... site practises, and headquarters - inspired by specific user needs for optimizing work processes. The most important mechanisms evoked for creating the mediating found in the paper are ‘hybrids’ where professionals from AEC establishes a software house, developing ICT-products for specific on...

Recent developments in collaborative CBRN decontamination science : a retrospective

Energy Technology Data Exchange (ETDEWEB)

Yanofsky, N. [Defence Research and Development Canada, Ottawa, ON (Canada); Volchek, K.; Fingas, M. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Division, Environmental Technology Centre, Science and Technology Branch; Filatov, B. [Research Inst. of Hygiene, Toxicology and Occupational Pathology, Volgograd (Russian Federation)

2006-07-01

The importance of addressing the risk of chemical, biological and radiological/nuclear (CBRN) attacks was discussed with particular reference to recent developments in Canadian-led decontamination studies as part of the remediation response to a terrorist attack. Research efforts have been supported by government programs such as the CBRN Research and Technology Initiative of Defence Research and Development Canada and the Global Partnership Program of the Department of Foreign Affairs. In 2005, Environment Canada and Defence Research and Development Canada co-organized an international workshop with the Research Institute of Health, Toxicology and Occupational Pathology of Volgograd, Russia. The workshop brought together researchers from Canada, Russia, United States, United Kingdom, Netherlands, Poland and Bulgaria, with the view to eventually develop longer term collaborations. The theme focused on membrane technology and its application in CBRN decontamination. This paper reviewed these collaborative and international research efforts and identified areas in need of future work, such as bioremediation and radio-nuclear remediation. It addressed issues supporting a collaborative international research agenda in decontamination science; membrane filtration as a feasible approach to decontamination waste treatment; and possible areas of CBRN collaboration. It was suggested that the key to successful decontamination requires the creation of computer systems for the initial identification of chemical substances; complete toxicological characterization of the most dangerous agents; regulatory safety standards; quantitative determination of chemical substances; antidotes for most chemical threat agents; universal decontamination agents; and, validation of criteria for decontaminating buildings. The question of who pays for decontamination, be it the private or public sector, was also discussed.

Key Issues in Global Technological Innovation Projects

Directory of Open Access Journals (Sweden)

Roberto Sbragia

2012-04-01

Full Text Available This article aimed to identify those issues that were present in global technological innovation projects carried out by Brazilian multinational companies and which performance criterions these undertakings met. We investigated 36 global technological innovation projects from Brazilian multinational enterprises through a web-survey. Findings show that these companies went beyond the traditional iron triangle to evaluate their technological efforts and considered additional performance dimensions such as customer satisfaction, business results, and preparation for the future. Results also show high degree of presence for issues emerging from the industry, moderate degree of presence for issues emerging from both the project and R&D activities, and low degree of presence for issues emerging from the headquarters, the subsidiaries, and the external environment. Further research is needed to find out if and how these issues influenced the performance of the global technological innovation projects studied.DOI:10.5585/gep.v3i1.72

Managing Innovation and Change for Instructional Technology.

Science.gov (United States)

Holznagel, Donald C.

1991-01-01

Introduces the term "orgware" and reviews the literature on managing technological innovation in instructional settings. Six areas of management concern are described, and advice on managing innovation and change is provided. (11 references) (GLR)

The differentiated impacts of organizational innovation practices on technological innovation persistence

OpenAIRE

Le Bas , Christian; Mothe , Caroline; Nguyen-Thi , Thuc Uyen

2015-01-01

International audience; Purpose – The purpose of this paper is to test the major determinants of technological (product and process) innovation persistence and provides evidence of the significant role of organizational innovation. Design/methodology/approach – Data came from two waves of the Luxembourg Community Innovation Survey (CIS): CIS2006 for 2004-2006 and CIS2008 for 2006-2008. The longitudinal data set resulted in a final sample of 287 firms. A multinomial probit model estimates the ...

Introduction to Innovative Food Processing and Technology

OpenAIRE

Tokusoglu, Ozlem

2015-01-01

Consumers, the food industry and the regulatory agencies demand the innovative technologies to provide safe and stable foods. Nonthermal processing technologies offer unprecedented opportunities and challenges for the food industry to market safe, high quality health-promoting foods. Those innovative food processing is often perceived as an alternative to thermal food processing, yet there are many nonthermal preparatory unit operations as well as food processing and preservation opportunitie...

Development of filtration equipment to reuse PFC decontamination wastewater

International Nuclear Information System (INIS)

Kim, Gye Nam; Lee, Sung Yeol; Won, Hui Jun; Jung Chong Hun; Oh, Won Zin; Park, Jin Ho

2005-01-01

When PFC(Perfluorocarbonate) decontamination technology is applied to removal of radioactive contaminated particulate adhered at surface during the operation of nuclear research facilities, it is necessary to develop a filtration equipment to reuse of PFC solution due to high price, also to minimize the volume of second wastewater. Contaminated characteristics of hot particulate was investigated and a filtration process was presented to remove suspended radioactive particulate from PFC decontamination wastewater generated on PFC decontamination

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.

1994-01-01

Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially of planned decommissioning operations. Thus lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for contaminated lead is removing the superficial layer of contamination with an abrasive medium under pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a scaled-off area. The slurry of abrasive and particles of lead falls through a floor and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling

Innovation Implementation: The Role of Technology Diffusion Agencies

Directory of Open Access Journals (Sweden)

Jasmin Robertson

2008-08-01

Full Text Available A great deal of ‘innovation failure’ can be attributed to ineffective implementation, rather than failure of the innovation itself. External agencies such as technology diffusion agencies (TDAs have been created to assist organisations to implement innovation successfully, but there has been little empirical research investigating their roles. This paper presents a longitudinal case study of failed innovation implementation, and highlights in particular the role that technology diffusion agencies can play to prevent such failure in future cases. Results indicate the importance of changes in organisational factors such as training, climate, and management support during the implementation process in predicting outcomes, and imply a role for TDAs in assisting with both technical and non-technical aspects of innovation implementation.

The role of technological innovation in creating radically new product meanings

DEFF Research Database (Denmark)

Krabbe, Anders Dahl

2015-01-01

This paper explores the concept of technological epiphanies from the literature on design driven innovation. A technological epiphany is defined as a product innovation that can be considered radical, both in terms of technology as well as the meaning and experiences it creates through its design....... Three cases of technological epiphanies from the hearing aid industry are analyzed and discussed in terms of how they represent a radical innovation in technology as well as in product meaning and which role the technological aspect has played in the radical innovation of the meaning of the product....... Three different ways in which technology can function as an enabler for the innovation of product meanings are explored and a fourth is found is found during the analysis. The paper concludes by suggesting directions for future research....

Software engineering technology innovation: Turning research results into industrial success

NARCIS (Netherlands)

Punter, H.T.; Krikhaar, R.L.; Bril, R.J.

2009-01-01

This paper deals with the innovation of software engineering technologies. These technologies are methods and tools for conducting software development and maintenance. We consider innovation as a process consisting of two phases, being technology creation and technology transfer. In this paper, we

Software engineering technology innovation - Turning research results into industrial success

NARCIS (Netherlands)

Punter, T.; Krikhaar, R.L.; Bril, R.J.

2009-01-01

This paper deals with the innovation of software engineering technologies. These technologies are methods and tools for conducting software development and maintenance. We consider innovation as a process consisting of two phases, being technology creation and technology transfer. In this paper, we

Innovative technology demonstrations

International Nuclear Information System (INIS)

Anderson, D.B.; Luttrell, S.P.; Hartley, J.N.

1992-08-01

Environmental Management Operations (EMO) is conducting an Innovative Technology Demonstration Program for Tinker Air Force Base (TAFB). Several innovative technologies are being demonstrated to address specific problems associated with remediating two contaminated test sites at the base. Cone penetrometer testing (CPT) is a form of testing that can rapidly characterize a site. This technology was selected to evaluate its applicability in the tight clay soils and consolidated sandstone sediments found at TAFB. Directionally drilled horizontal wells was selected as a method that may be effective in accessing contamination beneath Building 3001 without disrupting the mission of the building, and in enhancing the extraction of contamination both in ground water and in soil. A soil gas extraction (SGE) demonstration, also known as soil vapor extraction, will evaluate the effectiveness of SGE in remediating fuels and TCE contamination contained in the tight clay soil formations surrounding the abandoned underground fuel storage vault located at the SW Tanks Site. In situ sensors have recently received much acclaim as a technology that can be effective in remediating hazardous waste sites. Sensors can be useful for determining real-time, in situ contaminant concentrations during the remediation process for performance monitoring and in providing feedback for controlling the remediation process. Following the SGE demonstration, the SGE system and SW Tanks test site will be modified to demonstrate bioremediation as an effective means of degrading the remaining contaminants in situ. The bioremediation demonstration will evaluate a bioventing process in which the naturally occurring consortium of soil bacteria will be stimulated to aerobically degrade soil contaminants, including fuel and TCE, in situ

2006 Campus Technology Innovators

Science.gov (United States)

Campus Technology, 2006

2006-01-01

This article features the winners of this year's "Campus Technology Innovator" competition. The winners are: (1) Drexel University, Pennsylvania (outsourcing); (2) Darton College, Georgia (3D); (3) Minnesota State Colleges and Universities (ePortfolios); (4) University of Michigan (the Web); (5) University of Tennessee College of…

Essays on Energy Technology Innovation Policy

Science.gov (United States)

Chan, Gabriel Angelo Sherak

Motivated by global climate change, enhancing innovation systems for energy technologies is seen as one of the largest public policy challenges of the near future. The role of policy in enhancing energy innovation systems takes several forms: public provision of research and develop funding, facilitating the private sector's capability to develop new technologies, and creating incentives for private actors to adopt innovative and appropriate technologies. This dissertation explores research questions that span this range of policies to develop insights in how energy technology innovation policy can be reformed in the face of climate change. The first chapter of this dissertation explores how decision making to allocate public research and development funding could be improved through the integration of expert technology forecasts. I present a framework to evaluate and optimize the U.S. Department of Energy's research and development portfolio of applied energy projects, accounting for spillovers from technical complimentary and competition for the same market share. This project integrates one of the largest and most comprehensive sets of expert elicitations on energy technologies (Anadon et al., 2014b) in a benefit evaluation framework. This work entailed developing a new method for probability distribution sampling that accommodates the information that can be provided by expert elicitations. The results of this project show that public research and development in energy storage and solar photovoltaic technologies has the greatest marginal returns to economic surplus, but the methodology developed in this chapter is broadly applicable to other public and private R&D-sponsoring organizations. The second chapter of this dissertation explores how policies to transfer technologies from federally funded research laboratories to commercialization partners, largely private firms, create knowledge spillovers that lead to further innovation. In this chapter, I study the U

Efficiency of innovative technology in construction industry

Science.gov (United States)

Stverkova, H.; Vaclavik, V.

2017-10-01

The need for sustainability increasingly influences the development of new technologies, business processes and working practices. Innovations are an important part of all business processes. The aim of innovation is, in particular, to reduce the burden on the environment. The current trend in the construction industry is diamond rope cutting. The aim of the paper is to evaluate the most advanced technology for cutting and removing concrete structures in terms of efficiency.

Indigenous Technological Innovation : Capability and ...

International Development Research Centre (IDRC) Digital Library (Canada)

Indigenous Technological Innovation : Capability and Competitiveness in China's ... IDRC and key partners will showcase critical work on adaptation and ... Call for new OWSD Fellowships for Early Career Women Scientists now open.

Innovations in and by nuclear technology - review and perspectives

International Nuclear Information System (INIS)

Barthelt, K.

1984-01-01

An innovative technology like nuclear technology does not make progress by itself once it has to prove its profitability. It was a long way from technical to economic perfection which took courageous managemental descisions. Since nuclear fission was discovered, its exploitation as an energy source has been perfected. Now it is not only technically safe, reliable and ecological; it has also proved to be economically efficient as compared with the competing primary energies. As with other great innovations, the innovative force of nuclear technology is characterized by two directions: its assimilating capacity and its expanding capacity. Further issues are the so-called technological spin-off of nuclear technology and the fresh impetus nuclear technology gives to other fields. Another aspect beyond technological spin-off affecting all of our society: It was the first large technology requiring risk analyses to be carried out. Discussion broke out in public on the question: ''How safe is nuclear technology''. To sum up, the basic innovation of nuclear technology is now an important economic factor. It came just in time. It is capable of providing relief to the world's energy problems. It is up to us to use it in an intelligent way in the future despite any short-breathed complaints. (orig./HSCH) [de

Socio-economic research for innovative energy technologies

Energy Technology Data Exchange (ETDEWEB)

Ogawa, Yuichi [Tokyo Univ., High Temperature Plasma Center, Kashiwa, Chiba (Japan); Okano, Kunihiko [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

2006-10-15

In the 21st century global environment and energy issues become very important, and this is characterized by the long-term (in the scale of a few tens years) and world-wide issue. In addition, future prospect of these issues might be quite uncertain, and scientific prediction could be very difficult. For these issues vigorous researches and various efforts have been carried out from various aspects; e.g., world-wide discussion such as COP3 in Kyoto, promotion of the energy-saving technology and so on. Development of environment-friendly energy has been promoted, and new innovative technologies are explored. Nuclear fusion is, of course, a promising candidate. While, there might be some criticism for nuclear fusion from the socio-economic aspect; e.g., it would take long time and huge cost for the fusion reactor development. In addition, other innovative energy technologies might have their own criticism, as well. Therefore, socio-economic research might be indispensable for future energy resources. At first we have selected six items as for the characteristics, which might be important for future energy resources; i.e., energy resource, environmental load, economics, reliability/stability, flexibility on operation and safety/security. Concerning to innovative energy technologies, we have nominated seven candidates; i.e., advanced coal technology with CO2 recovery system, SOFC top combined cycle, solar power, wind power, space solar power station, advanced fission and fusion. Based on questionnaires for ordinary people and fusion scientists, we have tried to assess the fusion energy development, comparing with other innovative energy technologies. (author)

Energy, environment and technological innovation

Directory of Open Access Journals (Sweden)

Fernando José Pereira da Costa

2015-08-01

Full Text Available The development problems can not be addressed without taking account of the environmental and energy issues, as well as the intimate relationship and the intense interaction between the two. In fact, the energy issue can not be analyzed separately from environmental issues, nor the advances in technological innovation, integrating dynamic-systemic way and so positioning address the issue of the development model to set the bulge the transition process experienced by the world since the seventies of the twentieth century. This transition, in turn, implies the passage of Paradigm of Fossil Fuels to Renewable Energy also called the Paradigm of renewable sources of energy, not just holding the energy problem, but towards to environmental and technological components. It is within this relatively slow and long process, instigator of high levels of volatility, turbulence inducing and motor of technological innovation, which is (re raises the question of the development model that defines how a new model/style development.

Laser Decontamination of Surfaces Contaminated with Cs+ Ion

International Nuclear Information System (INIS)

Baigalmaaa, B.; Won, H. J.; Moon, J. K.; Jung, C. H.; Lee, K. W.; Hyun, J. H.

2008-01-01

Laser decontamination technology has been proven to be an efficient method for a surface modification of metals and concretes contaminated with radioactive isotopes. Furthermore, the generation of a secondary waste is negligible. The radioactivity of hot cells in the DFDF (Dupic Fuel Development Facility) is presumed to be very high and the predominant radionuclide is Cs-137. A series of laser decontamination studies by a fabricated Q-switched Nd:YAG laser system were performed on stainless steel specimens artificially contaminated with Cs+ ion. Decontamination characteristics of the stainless steel were analyzed by SEM and EPMA

The Impact of Financial Support System on Technology Innovation: A Case of Technology Guarantee System in Korea

Directory of Open Access Journals (Sweden)

Woo-Seok Jang

2008-04-01

Full Text Available We analyzed the impact of financial support system on technological innovation of small and medium manufacturing firms in Korea, with a special interest in technology guarantee system. This was done using a sample of 1,014 Korean manufacturing firms of which 43% were venture companies. Our study provides two important conclusions. First, the result of empirical analysis indicates that financial support systems have a significant influence on both product innovation and process innovation of SMEs in Korea. Second, a more important conclusion of this research is that technology guarantee system impacts on product innovation; however not on process innovation. This result implies that technology guarantee system attaches more importance to technological innovations related with product development than to those related with process enhancement.

MINERGY CORPORATION GLASS FURNACE TECHNOLOGY EVALUATION: INNOVATION TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

This report presents performance and economic data for a U.S. Environmental Protection Agency (EPA) Superfund Innovative Technology Evaluation (SITE) Program demonstration of the Minergy Corporation (Minergy) Glass Furnace Technology (GFT). The demonstration evaluated the techno...

Which One Triggers the Other? Technological or Social Innovation

Science.gov (United States)

Bulut, Cagri; Eren, Hakan; Halac, Duygu Seckin

2013-01-01

The term "innovation" has sometimes been used as a synonym for technological innovation until the concept of "social innovation" attracted academic attention. Since then, these two types of innovation have been investigated individually. It can be claimed that, despite the great importance of social innovation studies,…

Technology Foresight on Emerging Technologies: Implications for a National Innovation Initiative in Brazil

Directory of Open Access Journals (Sweden)

Maria Fatima Ludovico de Almeida

2015-07-01

Full Text Available Prospective studies about emerging technologies and their implications for public policy formulation indicate critical choices ranging from global to national level, even to the individual firm or institution. Emerging technologies have been shaping the future of some industries and transforming many others. In many cases, these technologies will determine the restructuring of industries as never before. Specially designed for enabling better planning and future decisions, technology foresight (TF methods are used to foresee diffusion of innovations, mapping out commercially viable roadmaps for technological development. This paper is concerned with a methodological instrument adopted in Brazil as support for building the Agenda for a National Innovation Initiative (NII, which was articulated by government, universities, R&D institutions, and private firms. It presents and discusses an integrated methodological approach for a TF study, specially designed for the purpose of this Brazilian innovation policy instrument, concerning three emerging technologies – nanotechnology, biotechnology, and information and communication technologies (ICT.

FY10 Engineering Innovations, Research and Technology Report

Energy Technology Data Exchange (ETDEWEB)

Lane, M A; Aceves, S M; Paulson, C N; Candy, J V; Bennett, C V; Carlisle, K; Chen, D C; White, D A; Bernier, J V; Puso, M A; Weisgraber, T H; Corey, B; Lin, J I; Wheeler, E K; Conway, A M; Kuntz, J D; Spadaccini, C M; Dehlinger, D A; Kotovsky, J; Nikolic, R; Mariella, R P; Foudray, A K; Tang, V; Guidry, B L; Ng, B M; Lemmond, T D; Chen, B Y; Meyers, C A; Houck, T L

2011-01-11

This report summarizes key research, development, and technology advancements in Lawrence Livermore National Laboratory's Engineering Directorate for FY2010. These efforts exemplify Engineering's nearly 60-year history of developing and applying the technology innovations needed for the Laboratory's national security missions, and embody Engineering's mission to ''Enable program success today and ensure the Laboratory's vitality tomorrow.'' Leading off the report is a section featuring compelling engineering innovations. These innovations range from advanced hydrogen storage that enables clean vehicles, to new nuclear material detection technologies, to a landmine detection system using ultra-wideband ground-penetrating radar. Many have been recognized with R&D Magazine's prestigious R&D 100 Award; all are examples of the forward-looking application of innovative engineering to pressing national problems and challenging customer requirements. Engineering's capability development strategy includes both fundamental research and technology development. Engineering research creates the competencies of the future where discovery-class groundwork is required. Our technology development (or reduction to practice) efforts enable many of the research breakthroughs across the Laboratory to translate from the world of basic research to the national security missions of the Laboratory. This portfolio approach produces new and advanced technological capabilities, and is a unique component of the value proposition of the Lawrence Livermore Laboratory. The balance of the report highlights this work in research and technology, organized into thematic technical areas: Computational Engineering; Micro/Nano-Devices and Structures; Measurement Technologies; Engineering Systems for Knowledge Discovery; and Energy Manipulation. Our investments in these areas serve not only known programmatic requirements of today and tomorrow, but

Effect of Organic Solvents in Preparation of Silica-Based Chemical Gel Decontaminates for Decontamination of Nuclear Facilities

International Nuclear Information System (INIS)

Yoon, Suk Bon; Jung, Chong Hun; Kim, Chang Ki; Choi, Byung Seon; Lee, Kune Woo; Moon, Jei Kwon

2011-01-01

Decontamination of nuclear facilities is necessary to reduce the radiation field during normal operations and decommissioning of complex equipment such as stainless steel components, other iron-based steel and alloys, metal surfaces, structural materials and so on. Chemical decontamination technology in particular is a highly effective method to remove the radioactive contamination through a chemical dissolution or a redox reaction. However, this method has the serious drawback due to the generation of large amounts of the radioactive liquid wastes. Recently, a few literatures have been reported for the preparation of the chemical gel decontaminants to reduce the amount of the radioactive liquid wastes and to enhance the decontamination efficiency through increasing the contact time between the gels and the radioactive contaminants. In the preparation of the chemical gels, the control of the viscosity highly depends on the amount of a coviscosifier used among the components of the chemical gels consisted of a viscosifier, a coviscosifier, and a chemical decontaminant. In this works, a new effective method for the preparation of the chemical gel was investigated by introducing the organic solvents. The mixture solution of the coviscosifier and organic solvent was more effective in the control of the viscosity compared with that of the coviscosifier only in gels. Furthermore, the decontamination efficiency of the chemical gels measured by using the multi-channel analyzer (MCA) showed the high decontamination factor for Co-60 and Cs-137 contaminated on the surface of the stainless steel 304

Minimizing the cost of subsea developments through technological innovation

International Nuclear Information System (INIS)

Eyre, G.; Loth, B.

1994-01-01

The paper summarizes the results of an extensive study carried out for the UK Government. This assessed the cost and economic impact of technological innovation on subsea and floating developments in the UKCS. The study covered, innovations that could be applied to subsea developments to significantly reduce cost, including multiwell completions, composite pipelines, compartmented pipelines, pipeline specification breaking and autonomous control systems. Cost and economic models were used to assess the economic impact of technological innovation on marginal field developments. The results of these assessments were drawn up as a series of ranking lists designed to assist manufacturers and suppliers in establishing priorities for research and development funding. The study also explored the potential UKCS and World market for innovative subsea technologies and quantified the research and development required to bring key innovations into commercial use

Quantitative Analysis of Technological Innovation in Urology.

Science.gov (United States)

Bhatt, Nikita R; Davis, Niall F; Dalton, David M; McDermott, Ted; Flynn, Robert J; Thomas, Arun Z; Manecksha, Rustom P

2018-01-01

To assess major areas of technological innovation in urology in the last 20 years using patent and publication data. Patent and MEDLINE databases were searched between 1980 and 2012 electronically using the terms urology OR urological OR urologist AND "surgeon" OR "surgical" OR "surgery". The patent codes obtained were grouped in technology clusters, further analyzed with individual searches, and growth curves were plotted. Growth rates and patterns were analyzed, and patents were correlated with publications as a measure of scientific support and of clinical adoption. The initial search revealed 417 patents and 20,314 publications. The top 5 technology clusters in descending order were surgical instruments including urinary catheters, minimally invasive surgery (MIS), lasers, robotic surgery, and image guidance. MIS and robotic surgery were the most emergent clusters in the last 5 years. Publication and patent growth rates were closely correlated (Pearson coefficient 0.78, P innovation and adoption into clinical practice. Patent metrics identify emergent technological innovations and such trends are valuable to understand progress in the field of urology. New surgical technologies like robotic surgery and MIS showed exponential growth in the last decade with good scientific vigilance. Copyright © 2017 Elsevier Inc. All rights reserved.

School-based data and management of technological innovations in ...

African Journals Online (AJOL)

School-based data and management of technological innovations in public secondary schools in Cross River State. ... Global Journal of Educational Research ... Result indicated that: there is no significant positive relationship between school-based data and principals management of technological innovation.

Developing technology intelligence strategy to access knowledge of innovation clusters.

OpenAIRE

Rani Jeanne Dang; Letizia Mortara; Ruth Thomson; Tim Minshall

2010-01-01

Current times are characterised by a knowledge-based economy and fast technological change. In this difficult environment, companies compete to maintain a relevant position through innovation. In response to these challenges, many companies are currently adopting an open approach to innovation, pursuing innovation by combining internal and external resources. Technology intelligence (TI) activities support the implementation of open innovation with the systematic capture and delivery of infor...

Four Essays on Technology Licensing and Firm Innovation

DEFF Research Database (Denmark)

Moreira, Solon

&D strategies. On the supply side, the existing literature has been focused on understanding how technology licensing can be used by firms as a mechanism to recover investments in innovative activities and to foster learning opportunities. On the demand side, it has been shown that licensing is an important...... source that firms can tap into to feed their internal needs for innovative knowledge. While several studies have examined technology licensing through the lens of the licensor, research on how firms rely on licensing contracts to acquire knowledge and improve their innovation performance still leaves......Licensing contracts represent one of the most widely used mechanisms to exchange technologies and transfer know-how between firms. Due to the opportunities that licensing creates for firms operating on both sides of the markets for technology, it has increasingly become an integral part of firms’ R...

Electrochemical decontamination system for actinide processing gloveboxes

International Nuclear Information System (INIS)

Wedman, D.E.; Lugo, J.L.; Ford, D.K.; Nelson, T.O.; Trujillo, V.L.; Martinez, H.E.

1998-03-01

An electrolytic decontamination technology has been developed and successfully demonstrated at Los Alamos National Laboratory (LANL) for the decontamination of actinide processing gloveboxes. The technique decontaminates the interior surfaces of stainless steel gloveboxes utilizing a process similar to electropolishing. The decontamination device is compact and transportable allowing it to be placed entirely within the glovebox line. In this way, decontamination does not require the operator to wear any additional personal protective equipment and there is no need for additional air handling or containment systems. Decontamination prior to glovebox decommissioning reduces the potential for worker exposure and environmental releases during the decommissioning, transport, and size reduction procedures which follow. The goal of this effort is to reduce contamination levels of alpha emitting nuclides for a resultant reduction in waste level category from High Level Transuranic (TRU) to low Specific Activity (LSA, less than or equal 100 nCi/g). This reduction in category results in a 95% reduction in disposal and disposition costs for the decontaminated gloveboxes. The resulting contamination levels following decontamination by this method are generally five orders of magnitude below the LSA specification. Additionally, the sodium sulfate based electrolyte utilized in the process is fully recyclable which results in the minimum of secondary waste. The process bas been implemented on seven gloveboxes within LANL's Plutonium Facility at Technical Area 55. Of these gloveboxes, two have been discarded as low level waste items and the remaining five have been reused

Innovative technologies in business hotels

Directory of Open Access Journals (Sweden)

Анастасия Игоревна Сидоренко

2015-10-01

Full Text Available The article analyzes the state and prospects of development of the hotel industry sector in Ukraine, aimed at a business audience that is constantly increasing; the need for the development and implementation of innovative technologies in a business hotel, because in the long term they will provide improving the service levels, the occupancy rate of the hotel rooms and competitiveness. An expediency of introducing innovative wireless LED lighting system in the rooms of business hotels is proved

A review of chemical decontamination systems for nuclear facilities

International Nuclear Information System (INIS)

Chen, L.; Chamberlain, D.B.; Conner, C.; Vandegrift, G.F.

1996-01-01

With the downsizing of the Department of Energy (DOE) complex, many of its buildings and facilities will be decommissioned and dismantled. As part of this decommissioning, some form of decontamination will be required. To develop an appropriate technology for in situ chemical decontamination of equipment interiors in the decommissioning of DOE nuclear facilities, knowledge of the existing chemical decontamination methods is needed. This paper attempts to give an up-to-date review of chemical decontamination methods. This survey revealed that aqueous systems are the most widely used for the decontamination and cleaning of metal surfaces. We have subdivided the aqueous systems by types of chemical solvent: acid, alkaline permanganate, highly oxidizing, peroxide, and proprietary. Two other systems, electropolishing and foams and gels, are also described in this paper

Technological Innovation and Cooperation for Foreign Information Access Program

Science.gov (United States)

Office of Postsecondary Education, US Department of Education, 2012

2012-01-01

The Technological Innovation and Cooperation for Foreign Information Access (TICFIA) Program supports projects focused on developing innovative technologies for accessing, collecting, organizing, preserving, and disseminating information from foreign sources to address the U.S.' teaching and research needs in international education and foreign…

Smart space technology innovations

CERN Document Server

Chen, Mu-Yen

2013-01-01

Recently, ad hoc and wireless communication technologies have made available the device, service and information rich environment for users. Smart Space and ubiquitous computing extend the ""Living Lab"" vision of everyday objects and provide context-awareness services to users in smart living environments. This ebook investigates smart space technology and its innovations around the Living Labs. The final goal is to build context-awareness smart space and location-based service applications that integrate information from independent systems which autonomously and securely support human activ

Cooperative technological innovation and competitiveness in the nuclear arena

International Nuclear Information System (INIS)

Castro Galvan, A.; Marco Pelegrin, M.; Salve Galiana, R.; Vallejo Haya, J.; Tagle Gonzalez, J. A.

2000-01-01

R and D and, more recently, technological innovation and its relationship with competitivity are more and more part of conferences, books, articles and political speeches and very often are the central part of them. Innovation has become fashionable and many initiatives have come out in connection with it. However, the relationship between technological innovation and competitivity are not always obvious. The current article intends to illustrate some mechanisms that link these two concepts through a specific case, DTN, that is already providing results for the Spanish nuclear industry and whose example can be extrapolated to other industrial sectors. The importance given by the nuclear to the innovation, the research and the technological development it is not new either exclusively belong to any specific organisation but makes evident the coherence between its traditional approach and the current idea of modernizing the country promoting the national technological capacity. (Author)

Innovation in concentrating solar power technologies: A study drawing on patent data

OpenAIRE

Braun, Frauke G.; Hooper, Elizabeth; Wand, Robert; Zloczysti, Petra

2010-01-01

Better understanding the innovative process of renewable energy technologies is important for tackling climate change. Though concentrating solar power is receiving growing interest, innovation studies so far have explored innovative activity in solar technologies in general, ignoring the major differences between solar photovoltaic and solar thermal technologies. This study relies on patent data to examine international innovative activity in concentrating solar power technologies. Our uniqu...

Fashion retail innovation: about context, antecedents and outcome in technological change projects

DEFF Research Database (Denmark)

Tambo, Torben

2015-01-01

Fashion retail is recognised for its strong capabilities in product innovation, while also having the potential to improve the governance of technology-based process innovation. This chapter proposes a model perspective in management of technology and innovation, including special requirements...... of fashion retailing. In particular, this chapter discusses the context of fashion retailing understood as product and brand-based characteristics. A case study-based methodology is then used to guide an analysis of antecedents and (expected) outcome of fashion retail innovation. IT-based innovation...... dominates, but innovation is suggested to include a broader scope of technologies. Contrary to innovation maturity models, this chapter proposes to consider innovation as a continuous refinement between dynamic capabilities and absorptive capacity where technologies must be adapted to the special...

Innovation of Energy Technologies: the role of taxes

OpenAIRE

Copenhagen Economics

2011-01-01

The study deals with the links between energy taxation and innovation and presents also new empirical evidence on the impact of energy taxes on patenting activities related to energy technologies. The study suggests that while taxation is a very effective driver of innovation, it can be usefully complemented with other public policy tools, such as public research grants and other technology policies.

CB decontamination for first responders

Energy Technology Data Exchange (ETDEWEB)

Mayer, M.D.G.; Purdon, J.G.; Burczyk, A. [Defence Research and Development Canada Suffield, Ralston, AB (Canada)

2006-07-01

The Universal Containment System (UCS) is designed to contain, mitigate and decontaminate chemical, biological and radiological warfare agents. The UCS consists of a lightweight, tent-like enclosure filled with a water-based surface decontaminating foam (SDF). The Canadian government funded a project to advance the understanding of the behaviour of the UCS. This paper described the success of the project as well as the technological advances in the UCS formulation and equipment. Vapour desorption experiments were conducted in which SDF was applied onto 12 surfaces found in a typical office environment. Both mustard and nerve agent were studied on the test surfaces. Both scrubbing and non-scrubbing decontamination methods were tested. SDF effectively decontaminated the non-porous substances, particularly when the scrubbing procedure was used. Results were more complicated for the non-porous samples. A dye added to the agent was useful for determining the fate of the agent. Liquid phase studies were conducted in which the reaction between SDF and various agents were studied in the liquid phase in order to estimate the rate of reaction, the stoichiometry and the reaction products formed. Both SDF and the commercial decontamination agent CASCAD were found to effectively kill 100 per cent of anthrax spores. The significance of this project to first responders was considerable. Changes to the formulation and equipment of UCS will increase its usefulness and safety. Users will also have a better knowledge of the amount of decontamination needed for complete effectiveness in specific situations. Recommendations have been made for use of the product on a range of indoor surfaces. Field trials have shown the blast mitigation and agent decontamination ability of the foam under explosive situations. 15 refs., 4 tabs.

Research on Upgrade Path to Technology Innovation of Resource-based SMEs in China

Science.gov (United States)

Jie, Xu

2017-08-01

Complexity, diversity and coordination are features of technology innovation of resource-based SMEs in China. This paper studies on the key factors of macro-environment, cooperation among enterprises and enterprise interior, which influence the upgrading of technology innovation of resource-based SMEs in China. This paper constructs integrated system of technology innovation to analyse the upgrade path to technology innovation of resource-based SMEs in China, so that enterprises would improve their technology innovation and get a new way to accomplish sustainable innovated development.

Innovations in Balloon Catheter Technology in Rhinology.

Science.gov (United States)

D'Anza, Brian; Sindwani, Raj; Woodard, Troy D

2017-06-01

Since being introduced more than 10 years ago, balloon catheter technology (BCT) has undergone several generations of innovations. From construction to utilization, there has been a myriad of advancements in balloon technology. The ergonomics of the balloon dilation systems have improved with a focus on limiting the extra assembly. "Hybrid" BCT procedures have shown promise in mucosal preservation, including treating isolated complex frontal disease. Multiple randomized clinical trials report improved long-term outcomes in stand-alone BCT, including in-office use. The ever-expanding technological innovations ensure BCT will be a key component in the armamentarium of the modern sinus surgeon. Copyright © 2017 Elsevier Inc. All rights reserved.

Technology certification and technology acceptance: Promoting interstate cooperation and market development for innovative technologies

International Nuclear Information System (INIS)

Brockbank, B.R.

1995-03-01

In the past two years, public and private efforts to promote development and deployment of innovative environmental technologies have shifted from the analysis of barriers to the implementation of a variety of initiatives aimed at surmounting those barriers. Particular attention has been directed at (1) streamlining fragmented technology acceptance processes within and among the states, and (2) alleviating disincentives, created by inadequate or unverified technology cost and performance data, for users and regulators to choose innovative technologies. Market fragmentation currently imposes significant cost burdens on technology developers and inhibits the investment of private capital in environmental technology companies. Among the responses to these problems are state and federal technology certification/validation programs, efforts to standardize cost/performance data reporting, and initiatives aimed at promoting interstate cooperation in technology testing and evaluation. This paper reviews the current status of these initiatives, identifies critical challenges to their success, and recommends strategies for addressing those challenges

Development of new chemical and electrochemical decontamination methods for selected equipment of WWER-440 and WWER-1000 reactor primary circuit

International Nuclear Information System (INIS)

Solcanyi, M.; Majersky, D.

1998-01-01

Special devices for in-situ application of decontamination technologies assigned for Steam Generator, Pressurizer and Main Circulating Casing of WWER-1000 type were designed, manufactured and tested in real conditions of their use in above Primary Circuit components. New decontamination technologies like low-concentration process NP-NHN for the decontamination of the Steam Generator, combined chemico-mechanical treatment for the Pressurizer and semi-dry electrolysis for the Main Circulating Pump Casing were developed and approved for their safe plant application from point of view of decontamination efficiency, corrosion influence and processing of secondary wastes. Main technological parameters were defined to achieve high decontamination efficiency and corrosion-safe application of all decontamination technologies. (author)

Climatic shocks associate with innovation in science and technology

NARCIS (Netherlands)

C.K.W. de Dreu (Carsten); Dijk, M.A. (Mathijs) van

2018-01-01

textabstractHuman history is shaped by landmark discoveries in science and technology. However, across both time and space the rate of innovation is erratic: Periods of relative inertia alternate with bursts of creative science and rapid cascades of technological innovations. While the origins of

Innovative technologies for in-situ remediation

International Nuclear Information System (INIS)

Ragaini, R.; Aines, R.; Knapp, R.; Matthews, S.; Yow, J.

1994-06-01

LLNL is developing several innovative remediation technologies as long-term improvements to the current pump and treat approaches to cleaning up contaminated soils and groundwater. These technologies include dynamic underground stripping, in-situ microbial filters, and remediation using bremsstrahlung radiation. Concentrated underground organic contaminant plumes are one of the most prevalent groundwater contamination sources. The solvent or fuel can percolate deep into the earth, often into water-bearing regions. Collecting as a separate, liquid organic phase called dense non-aqueous-phase liquids (DNAPLs), or light NAPLs (LNAPLs), these contaminants provide a source term that continuously compromises surrounding groundwater. This type of spill is one of the most difficult environmental problems to remediate. Attempts to remove such material requires a huge amount of water which must be washed through the system to clean it, requiring decades. Traditional pump and treat approaches have not been successful. LLNL has developed several innovative technologies to clean up NAPL contamination. Detailed descriptions of these technologies are given

Application of Ultrasonic for Decontamination of Contaminated Soil - 13142

International Nuclear Information System (INIS)

Vasilyev, A.P.; Lebedev, N.M.; Savkin, A.E.

2013-01-01

The trials of soil decontamination were carried out with the help of a pilot ultrasonic installation in different modes. The installation included a decontamination bath equipped with ultrasonic sources, a precipitator for solution purification from small particles (less than 80 micrometer), sorption filter for solution purification from radionuclides washing out from soil, a tank for decontamination solution, a pump for decontamination solution supply. The trials were carried out on artificially contaminated sand with specific activity of 4.5 10 5 Bk/kg and really contaminated soil from Russian Scientific Center 'Kurchatovsky Institute' (RSC'KI') with specific activity of 2.9 10 4 Bk/kg. It was established that application of ultrasonic intensify the process of soil reagent decontamination and increase its efficiency. The decontamination factor for the artificially contaminated soil was ∼200 and for soil from RSC'KI' ∼30. The flow-sheet diagram has been developed for the new installation as well as determined the main technological characteristics of the equipment. (authors)

DECONTAMINATION/DESTRUCTION TECHNOLOGY DEMONSTRATION FOR ORGANICS IN TRANSURANIC WASTE

Energy Technology Data Exchange (ETDEWEB)

Chris Jones; Javier Del Campo; Patrick Nevins; Stuart Legg

2002-08-01

The United States Department of Energy's Savannah River Site has approximately 5000 55-gallon drums of {sup 238}Pu contaminated waste in interim storage. These may not be shipped to WIPP in TRUPACT-II containers due to the high rate of hydrogen production resulting from the radiolysis of the organic content of the drums. In order to circumvent this problem, the {sup 238}Pu needs to be separated from the organics--either by mineralization of the latter or by decontamination by a chemical separation. We have conducted ''cold'' optimization trials and surrogate tests in which a combination of a mediated electrochemical oxidation process (SILVER II{trademark}) and ultrasonic mixing have been used to decontaminate the surrogate waste materials. The surrogate wastes were impregnated with copper oxalate for plutonium dioxide. Our process combines both mineralization of reactive components (such cellulose, rubber, and oil) and surface decontamination of less reactive materials such as polyethylene, polystyrene and polyvinylchloride. By using this combination of SILVER II and ultrasonic mixing, we have achieved 100% current efficiency for the destruction of the reactive components. We have demonstrated that: The degree of decontamination achieved would be adequate to meet both WIPP waste acceptance criteria and TRUPACT II packaging and shipping requirements; The system can maintain near absolute containment of the surrogate radionuclides; Only minimal pre-treatment (coarse shredding) and minimal waste sorting are required; The system requires minimal off gas control processes and monitoring instrumentation; The laboratory trials have developed information that can be used for scale-up purposes; The process does not produce dioxins and furans; Disposal routes for secondary process arisings have already been demonstrated in other programs. Based on the results from Phase 1, the recommendation is to proceed to Phase 2 and use the equipment at Savannah

Climatic shocks associate with innovation in science and technology.

Science.gov (United States)

De Dreu, Carsten K W; van Dijk, Mathijs A

2018-01-01

Human history is shaped by landmark discoveries in science and technology. However, across both time and space the rate of innovation is erratic: Periods of relative inertia alternate with bursts of creative science and rapid cascades of technological innovations. While the origins of the rise and fall in rates of discovery and innovation remain poorly understood, they may reflect adaptive responses to exogenously emerging threats and pressures. Here we examined this possibility by fitting annual rates of scientific discovery and technological innovation to climatic variability and its associated economic pressures and resource scarcity. In time-series data from Europe (1500-1900CE), we indeed found that rates of innovation are higher during prolonged periods of cold (versus warm) surface temperature and during the presence (versus absence) of volcanic dust veils. This negative temperature-innovation link was confirmed in annual time-series for France, Germany, and the United Kingdom (1901-1965CE). Combined, across almost 500 years and over 5,000 documented innovations and discoveries, a 0.5°C increase in temperature associates with a sizable 0.30-0.60 standard deviation decrease in innovation. Results were robust to controlling for fluctuations in population size. Furthermore, and consistent with economic theory and micro-level data on group innovation, path analyses revealed that the relation between harsher climatic conditions between 1500-1900CE and more innovation is mediated by climate-induced economic pressures and resource scarcity.

Environmental decontamination

International Nuclear Information System (INIS)

Cristy, G.A.; Jernigan, H.C.

1981-02-01

The record of the proceedings of the workshop on environmental decontamination contains twenty-seven presentations. Emphasis is placed upon soil and surface decontamination, the decommissioning of nuclear facilities, and assessments of instrumentation and equipment used in decontamination

Analysis of decontamination methods used at nuclear power plants and in other facilities. Research report

International Nuclear Information System (INIS)

Podlaha, Josef

2011-10-01

Methods used in the Czech Republic and in other countries are described. The following topics are treated: Introduction into decontamination; Chemical methods; Foam methods; Electrochemical methods; Mechanical methods; Other methods; Decontamination of civil engineering structures; Technologies suitable for disposal decontamination; and Effect of decontamination on waste management. (P.A.)

76 FR 80901 - National Medal of Technology and Innovation Nomination Evaluation Committee

Science.gov (United States)

2011-12-27

... Nation's highest honor for technological innovation, awarded annually by the President of the United... utilizing technological innovation and/or be familiar with the education, training, employment and... Management/Computing/IT/Manufacturing Innovation; Technological Manpower/Workforce Training/Education. Under...

Westinghouse Savannah River Site vendor forum: An innovative cooperative technology development success

International Nuclear Information System (INIS)

Sturm, H.F. Jr.

1996-01-01

The Westinghouse Savannah River Company (WSRC) Supplier Environmental and Waste Management Information Exchange Forum was held August 31 - September 1, 1993. The forum, which was planned and conducted in concert with the Department of Energy Savannah River Operations Office (DOE-SROO), was held to foster a technical exchange in which new, innovative technologies were proposed by suppliers, to identify more cost-effective methods to apply to future and on-going activities, to increase use of the private sector, and to promote partnerships with other industries. The two day forum provided the opportunity for WSRC and DOE-SR to review program activities and challenges in five major areas, Savannah River Technology Center, Solid Waste Facilities, Environmental Restoration, Environmental Monitoring, and Decontamination and Decommissioning through formal presentations. The second day was designed to provide suppliers the opportunity to talk about current and future activities and challenges with representatives of each of these areas at display booths, special high interest topic interactive sessions, and site tours. Each attendee was then invited to submit pre-proposals relative to the abstracts presented in The Special Consolidate Solicitation for Environmental and Waste Management Basic and Applied Research and Research-Related Development and/or Demonstration No. E10600-E1 document. Twenty-five contracts totaling $12 million were awarded. Twenty-four contracts have now been completed. This paper provides an overview of the pre forum activities, the forum, post-forum and proposal review process, and most importantly a description of the technologies demonstrated, the benefits and savings derived, and future use potential from a DOE perspective, as well as technology transfer and industrial partnership potential

Accelerating nano-technological innovation in the Danish construction industry

DEFF Research Database (Denmark)

Koch, Christian; Stissing Jensen, Jens

2007-01-01

. The institutional features of the system are furthermore poorly equipped at identifying potentials within high-tech areas. In order to exploit the potentials of nano-technology it is thus argued that an alternative TIS needs to be established. Initiatives should identify and support "incubation rooms" or marked......  By viewing the construction industry as a technological innovation system (TIS) this paper discusses possible initiatives to accelerate nanotechnological innovations. The point of departure is a recent report on the application of nano-technology in the Danish construction industry, which...... concludes that opportunities are generally poorly appreciated by the industry and research communities alike. It is found that the construction industry is characterised by low-tech trajectories where dedicated innovation networks are often too fragile for innovations to stabilize and diffuse...

Environmental decontamination

Energy Technology Data Exchange (ETDEWEB)

Cristy, G.A.; Jernigan, H.C. (eds.)

1981-02-01

The record of the proceedings of the workshop on environmental decontamination contains twenty-seven presentations. Emphasis is placed upon soil and surface decontamination, the decommissioning of nuclear facilities, and assessments of instrumentation and equipment used in decontamination. (DLS)

Pickering emulsions for skin decontamination.

Science.gov (United States)

Salerno, Alicia; Bolzinger, Marie-Alexandrine; Rolland, Pauline; Chevalier, Yves; Josse, Denis; Briançon, Stéphanie

2016-08-01

This study aimed at developing innovative systems for skin decontamination. Pickering emulsions, i.e. solid-stabilized emulsions, containing silica (S-PE) or Fuller's earth (FE-PE) were formulated. Their efficiency for skin decontamination was evaluated, in vitro, 45min after an exposure to VX, one of the most highly toxic chemical warfare agents. Pickering emulsions were compared to FE (FE-W) and silica (S-W) aqueous suspensions. PE containing an oil with a similar hydrophobicity to VX should promote its extraction. All the formulations reduced significantly the amount of VX quantified on and into the skin compared to the control. Wiping the skin surface with a pad already allowed removing more than half of VX. FE-W was the less efficient (85% of VX removed). The other formulations (FE-PE, S-PE and S-W) resulted in more than 90% of the quantity of VX removed. The charge of particles was the most influential factor. The low pH of formulations containing silica favored electrostatic interactions of VX with particles explaining the better elimination from the skin surface. Formulations containing FE had basic pH, and weak interactions with VX did not improve the skin decontamination. However, these low interactions between VX and FE promote the transfer of VX into the oil droplets in the FE-PE. Copyright © 2016 Elsevier B.V. All rights reserved.

Zirconium Hydroxide-coated Nanofiber Mats for Nerve Agent Decontamination.

Science.gov (United States)

Kim, Sohee; Ying, Wu Bin; Jung, Hyunsook; Ryu, Sam Gon; Lee, Bumjae; Lee, Kyung Jin

2017-03-16

Diverse innovative fabrics with specific functionalities have been developed for requirements such as self-decontamination of chemical/biological pollutants and toxic nerve agents. In this work, Zr(OH) 4 -coated nylon-6,6 nanofiber mats were fabricated for the decontamination of nerve agents. Nylon-6,6 fabric was prepared via the electrospinning process, followed by coating with Zr(OH) 4 , which was obtained by the hydrolysis of Zr(OBu) 4 by a sol-gel reaction on nanofiber surfaces. The reaction conditions were optimized by varying the amounts of Zr(OBu) 4 ,the reaction time, and the temperature of the sol-gel reaction. The composite nanofibers show high decontamination efficiency against diisopropylfluorophosphate, which is a nerve agent analogue, due to its high nucleophilicity that aids in the catalysis of the hydrolysis of the phosphonate ester bonds. Composite nanofiber mats have a large potential and can be applied in specific fields such as military and medical markets. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dilute chemical decontamination resins and the mixed waste issue

International Nuclear Information System (INIS)

Denault, R.P.; Hallman, J.T.

1988-01-01

The decontamination of reactor primary systems, sub-systems and components is an important method used to reduce the occupational radiation exposure of nuclear plant personnel. The waste produced by the application of this technology is mainly solid in the form of ion exchange resins. As a result of a recent agreement between the Environmental Protection Agency (EPA) and the Nuclear Regulatory Commission (NRC), all radioactive waste must meet EPA burial criteria. The chemicals used in a decontamination and certain metals dissolved during the process, primarily chromium, could render the waste hazardous as well as radioactive or more commonly called a mixed waste. This paper defines mixed waste as described in the EPA directive 9432.00-2, and examine the criteria by which waste is categorized as hazardous. The decontamination waste resin generated by two processes, the CAN-DEREM and the LOMI process, is described in detail. Waste data obtained from decontaminations performed by LN Technologies Corporation including chemical, metal and radionuclide loadings on resins from both PWR and BWR applications are presented

Radiation decontamination of dry food ingredients and processing aids

Energy Technology Data Exchange (ETDEWEB)

Farkas, J

1984-01-01

Radiation decontamination of dry ingredients, herbs and enzyme preparations is a technically feasible, economically viable and safe physical process. The procedure is direct, simple, requires no additives and is highly efficient. Its dose requirement is moderate. Radiation doses of 3-10 kGy (0.3-1 mrad) have proved sufficient to reduce the viable counts to a satisfactory level. Ionising radiations do not cause any significant rise in temperature. The flavour, texture or other important technological or sensory properties of most ingredients are not influenced at radiation doses necessary for satisfactory decontamination, and radiation obviates the chemical residue problem. The microflora surviving radiation decontamination of dry ingredients are more susceptible to subsequent antimicrobial treatments. Recontamination can be prevented as the product can be irradiated in its final packaging. Irradiation could be carried out in commercial containers and would result in considerable savings of energy and labour as compared to alternative decontamination techniques. Radiation processing of these commodities is an established technology in several countries and more clearances on irradiated foods are expected to be granted in the near future.

Innovative activity of high-technology companies as assessment and forecasting object

Directory of Open Access Journals (Sweden)

A. E. Sklyarov

2016-01-01

Full Text Available Innovation activities, as well as innovations, are closely related meanings, and like many others economical definitions, have a broad range of meanings. Main characteristics and attributes of innovation involves new or significantly improved product, that’s being used, or in other words, found its application, and innovative activities – activities focused on realization of innovations. In this article, innovations are mainly considered in terms of high-technology production, evidence from Russian space industry. There are 5 basic stages of lifecycle of innovative project in considered industry: initiation, development, realization, expansion, consumption. Practically, third or fourth, or even both of these stages, often missing because there is no need of them. R&D activities, or even further serial production, based on previous developments, is an innovation activity, because these activities are stages of innovative projects lifecycle itself. Then it seems legit, to draw a conclusion, that in terms of high-technology production, company’s primary activity equals innovative activity. Basic characteristics of innovative activity of high-technology companies as assessment and forecasting object involves high level of uncertainty at every stage of projects lifecycle, high dependency on funding level of this activity, and high level and erratic structure of risk. All the above mentioned, means that assessment and forecasting of innovative activity of high-technology companies, needs development of its own methodological tools for each industry.

The reuse of scrap and decontamination waste water from decommissioning

International Nuclear Information System (INIS)

Deng Junxian; Li Xin; Xie Xiaolong

2010-01-01

Huge amount of radioactive scrap with low activity will be generated from reactor decommissioning; the decontamination is concentrated in the surface layer of the scrap. The decontaminated substance can be removed by high pressure water jet to appear the base metal and to reuse the metal. Big amount of radioactive waste water will be generated by this decontamination technology; the radioactive of the waste water is mainly caused by the solid particle from decontamination. To remove the solid particle as clean as possible, the waste water can be reused. Different possible technology to remove the solid particle from the water had been investigated, such as the gravity deposit separation, the filtration and the centrifugal separation etc. The centrifugal separation technology is selected; it includes the hydraulic vortex, the centrifugal filtration and the centrifugal deposit. After the cost benefit analysis at last the centrifugal deposit used butterfly type separator is selected. To reuse the waste water the fresh water consumption and the cost for waste water treatment can be reduced. To reuse the radioactive scrap and the waste water from decommissioning will minimize the radioactive waste. (authors)

Marginalization of end-use technologies in energy innovation for climate protection

Science.gov (United States)

Wilson, Charlie; Grubler, Arnulf; Gallagher, Kelly S.; Nemet, Gregory F.

2012-11-01

Mitigating climate change requires directed innovation efforts to develop and deploy energy technologies. Innovation activities are directed towards the outcome of climate protection by public institutions, policies and resources that in turn shape market behaviour. We analyse diverse indicators of activity throughout the innovation system to assess these efforts. We find efficient end-use technologies contribute large potential emission reductions and provide higher social returns on investment than energy-supply technologies. Yet public institutions, policies and financial resources pervasively privilege energy-supply technologies. Directed innovation efforts are strikingly misaligned with the needs of an emissions-constrained world. Significantly greater effort is needed to develop the full potential of efficient end-use technologies.

CO{sub 2} pellet decontamination technology at Westinghouse Hanford

Energy Technology Data Exchange (ETDEWEB)

Aldridge, T.L.; Aldrich, L.K. II; Bowman, E.V. [Westinghouse Hanford Co., Richland, WA (United States)

1995-03-01

Experimentation and testing with CO{sub 2} pellet decontamination technology is being conducted at Westinghosue Hanford Company (WHC), Richland, Washington. There are 1,100 known existing waste sites at Hanford. The sites specified by federal and state agencies are currently being studied to determine the appropriate cleanup methods best for each site. These sites are contaminated and work on them is in compliance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). There are also 63 treatment, storage, and disposal units, for example: groups of waste tanks or drums. In 1992, there were 100 planned activities scheduled to bring these units into the Resource Conservation and Recovery Act (RCRA) compliance or close them after waste removal. Ninety-six of these were completed. The remaining four were delayed or are being negotiated with regulatory agencies. As a result of past defense program activities at Hanford a tremendous volume of materials and equipment have accumulated and require remediation.

Chemical decontamination method

International Nuclear Information System (INIS)

Nishiwaki, Hitoshi.

1996-01-01

Metal wastes contaminated by radioactive materials are contained in a rotational decontamination vessel, and the metal wastes are rotated therein while being in contact with a slight amount of a decontamination liquid comprising a mineral acid. As the mineral acid, a mixed acid of nitric acid, hydrochloric acid and fluoric acid is preferably used. Alternatively, chemical decontamination can also be conducted by charging an acid resistant stirring medium in the rotational decontamination vessel. The surface of the metal wastes is uniformly covered by the slight amount of decontamination liquid to dissolve the surface layer. In addition, heat of dissolution generated in this case is accumulated in the inside of the rotational decontamination vessel, the temperature is elevated with no particular heating, thereby enabling to obtain an excellent decontamination effect substantially at the same level as in the case of heating the liquid to 70degC in a conventional immersion decontamination method. Further, although contact areas between the metal wastes and the immersion vessel are difficult to be decontaminated in the immersion decontamination method, all of areas can be dissolved uniformly in the present invention. (T.M.)

Metallic surfaces decontamination by using laser light

International Nuclear Information System (INIS)

Moggia, Fabrice; Lecardonnel, Xavier

2013-01-01

Metal surface cleaning appears to be one of the major priorities for industries especially for nuclear industries. The research and the development of a new technology that is able to meet the actual requirements (i.e. waste volume minimization, liquid effluents and chemicals free process...) seems to be the main commitment. Currently, a wide panel of technologies already exists (e.g. blasting, disk sander, electro-decontamination...) but for some of them, the efficiency is limited (e.g, Dry Ice blasting) and for others, the wastes production (liquid and/or solid) remains an important issue. One answer could be the use of a LASER light process. Since a couple of years, the Clean- Up Business Unit of the AREVA group investigates this decontamination technology. Many tests have been already performed in inactive (i.e. on simulants such as paints, inks, resins, metallic oxides) or active conditions (i.e. pieces covered with a thick metallic oxide layer and metallic pieces covered with grease). The paper will describe the results obtained in term of decontamination efficiency during all our validation process. Metallographic characterizations (i.e. SEM, X-ray scattering) and radiological analysis will be provided. We will also focus our paper on the future deployment of the LASER technology and its commercial use at La Hague reprocessing facility in 2013. (authors)

Bringing to Market Technological Innovation: What Distinguishes Success from Failure

Directory of Open Access Journals (Sweden)

Federico Frattini

2012-09-01

Full Text Available Commercialization is a critical step in technological innovation. Nevertheless, many scholars believe that it is often the least well-managed activity of the whole innovation process. The launch stage seems to be particularly critical in high-technology markets because of the volatility, interconnectedness and the proliferation of new technologies they experience. However, academic and practitioners’ literature has not, so far, developed a clear understanding of the factors that distinguish an effective commercialization from an unsuccessful one, especially in high-technology environments. This paper discusses the results of a research project that aimed to understand the ingredients for success in the commercialization of a technological innovation. The first stage of the research consisted of a comparative historical analysis of 18 innovations, which were commercialized in consumer high-tech markets in the last 30 years. The analysis advocates that an effective commercialization comprises three sub-strategies: Early adoption strategy, Adoption network configuration strategy and Mainstream adoption strategy, with each one characterized by a coherent set of commercialization dimensions. The relative importance of each sub-strategy in determining the innovation commercial success depends on the type of innovation that is commercialized, be it radical or incremental and discontinuous or continuous.

Decontamination for radiators by friction effect

International Nuclear Information System (INIS)

Nojima, Takeshi; Yoshida, Yuji

2016-01-01

Radiators are equipped with cars, vending machines and outdoor units of air conditioners. Aluminum metal surfaces in their heat exchange part have been contaminated by radioactive material taking in dust after the nuclear accident. The dust adhering to the metal surface could be removed by flushing with water immediately after scattering radioactive material. But radioactive material such as cesium cannot be removed by water washing, because of growth of the oxide film and transfer of the nuclides in the metal surface due to aging. On the other hand, we have verified the effect of decontamination of radiators by friction cleaning using a cross flow shredder (CFS) and solvent washing of crushed metallic chips, as a different approach to high-pressure washing decontamination, and confirmed a certain decontamination effect. This paper describes the results of program, “Processing Technology of Radioactive Material Removal by Cross Flow Shredder,” in August to December 2015, on support of FY 2015 Demonstration Test Project for Decontamination and Volume Reduction of Ministry of the Environment. (author)

Chemical and Biological Substances Decontamination Study for Mars Missions and Terrestrial Applications

Science.gov (United States)

Pottage, Thomas; Walker, James; Bennett, Allan; Vrublevskis, John; Hovland, Scott

This study, funded by the European Space Agency (ESA) and undertaken by the Health Protec-tion Agency, UK supported by Systems Engineering and Assessment Ltd., was devised to select suitable current decontamination technologies for development for future manned missions to the Moon and Mars. There is a requirement to decontaminate the habitat module due to the concerns about astronaut ill health, microbial deterioration of materials and potential forward contamination in the case of Mars. In the case of the MIR space station, biodeterioration of components and materials occurred, and dangerous levels of airborne microorganisms were detected during air sampling procedures which lead to the introduction of microbial exposure limits (as MORD SSP 50260) to ensure the health of the crew. COSPAR planetary protection guidelines highlight the need to reduce any potential forward or backwards contamination issues that may occur through the use of Extra Vehicular Activity (EVA) suits whilst on Mars. Decontamination of the suit exterior must be completed before any EVA activity on Mars, whilst a further decontamination cycle must be completed after entry to the airlock following EVA. Technologies and techniques have also been investigated for the microbial reduction of the interior surfaces of the EVA suit to stop biodeterioration of the materials and protect the user from pathogenic microbe accumulation. The first work package reviewed the systems description and requirements as detailed in the statement of work. The requirements were broken down into 12 further requirement sections, where they were updated and expanded, resulted in Technical Note (TN) 1 which was then used as the base document for WP2 and WP3. WP2 investigated the current technologies available for the decontamination of the habitat module interior on missions of up to 6 months and missions that have durations of greater than 6 months. A comprehensive review was carried out for the different methods that

Demonstration and evaluation of the CORPEX trademark Nuclear Decontamination Process, Technical task plan No. SR152005. Final Report

International Nuclear Information System (INIS)

May, C.G.

1997-01-01

In June, 1995, the Decontamination and Decommissioning Focus Area funded a demonstration of the CORPEX Nuclear Decontamination Process in an Old Metallography Laboratory glovebox at the Savannah River Site. The objective of the demonstration was to prove the effectiveness of a new and innovative technology that would reduce the risks associated with future cleanups of plutonium-238 contaminated equipment in the DOE complex. After facility and vendor preparations in support of the demonstration, Westinghouse Savannah River Company (WSRC) was informed by the vendor that the chemistry proposed for use in the decontamination process was not effective on sintered plutonium, which was the form of plutonium in the selected glovebox. After further technical evaluation, the demonstration was canceled. This report describes the work performed in support of the demonstration and the present status of the project. The CORPEX chemical process is a nondestructive cleaning method that removes only the contaminant and the matrix that fixed the contaminant to the surface. It does not damage the substrate. The cleaning agent is destroyed by the addition of proprietary oxidizers, leaving water, carbon dioxide and nitrogen gases, and a sludge as waste

The role of technological innovation in sustainable economic development

OpenAIRE

Andreea Constantinescu; Simona Frone

2014-01-01

As in science an accurate picture of present is highlighted from a future outlook, we should recognize the crucial role of new technologies and innovation to improve knowledge in this field. They may give guarantee of sustainable economic development, provided prioritization of research in some fields such as: information technology and communication, resource depletion and climate change. Technological innovation becomes support of all strategies and policies aimed at ensuring sustainable ec...

INNOVATION TRENDS ON INFORMATION AND COMMUNICATION TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Radu CURETEANU

2010-12-01

Full Text Available The importance of innovation was long underestimated in service activities. In contrast to the radical innovations vital to growth in manufacturing sectors, innovations in services and tourism were secondary and capital-scarce, and for this reason they were excluded from the scope of government interest and action. It is interesting to note that the discourse changed with the emergence of new information and communication technologies, which have been especially influential in the realm of tourism.

The power of design product innovation in sustainable energy technologies

CERN Document Server

Reinders, Angele H; Brezet, Han

2012-01-01

The Power of Design offers an introduction and a practical guide to product innovation, integrating the key topics that are necessary for the design of sustainable and energy-efficient products using sustainable energy technologies. Product innovation in sustainable energy technologies is an interdisciplinary field. In response to its growing importance and the need for an integrated view on the development of solutions, this text addresses the functional principles of various energy technologies next to the latest design processes and innovation methods. From the perspec

Concrete decontamination: two innovative processes in response to surface or deep contamination

International Nuclear Information System (INIS)

CUER, F.; Nadai, A. de; Faure, S.

2008-01-01

To meet the future needs in the nuclear industry as regards dismantling and decommissioning, the LPAD (Laboratoire des Procedes Avances de Decontamination) develops new specific techniques to decontaminate concretes: the drying gel process adapted to surface contamination and the electrokinetics process to treat deep contamination. Indeed, because the concrete constitute a porous medium, two types of contamination can be met according to the environment to which is subjected the material. In the case of an accidental or dry contamination, radio elements do not penetrate beyond the first millimeters of the material. The contamination is then considered as surface. On the contrary, the contamination is considered as 'deep' when radioactive ions have diffused deeply under the effects of the natural diffusion. This is the case in fuel storage pond or other many nuclear infrastructures. (authors)

Business Models and Technological Innovation

OpenAIRE

Baden-Fuller, Charles; Haefliger, Stefan

2013-01-01

Business models are fundamentally linked with technological innovation, yet the business model construct is essentially separable from technology. We define the business model as a system that solves the problem of identifying who is (or are) the customer(s), engaging with their needs, delivering satisfaction, and monetizing the value. The framework depicts the business model system as a model containing cause and effect relationships, and it provides a basis for classification. We formulate ...

Skin decontamination

International Nuclear Information System (INIS)

Moehrle, G.

1975-01-01

A general survey of skin decontamination is given. The success of every decontamination treatments depends mainly on the speed, but also on the care, with which the action is taken. The best way to remove the skin contaminants is thorough washing under lukewarm running water with mild soap and a soft brush. This washing is to be repeated several times for a period of several minutes. If results are not satisfactory, light duty detergents and wetting agents available commercially may also be used. Some solutions which have proved useful are mentioned. The decontamination solutions are best used in the order given. When one has no satisfactory decontamination effect, the next one is to be used. If necessary, these agents must be used several times in the stated order as long as this does not involve too much strain for the skin. All the decontamination measures mentioned refer, of course, to intact healthy skin. After decontamination has been completed, the skin should be treated with a protective cream

OPEN INNOVATION PROJECT: THE SYSTEM OF ONLINE INDICATORS IN SCIENCE, TECHNOLOGY AND INNOVATION OF AMAZONAS (SiON

Directory of Open Access Journals (Sweden)

Moises Andrade Coelho

2016-05-01

Full Text Available This study aims to evaluate the implementation of an open innovation project in a public institution in the state of Amazonas. The theoretical and empirical background deals with science, technology and innovation indicators and open innovation. The study is characterized as a qualitative and descriptive research, with the case study as a methodological procedure. The delimitation of the universe was composed by a public institution in the area of science, technology and innovation (ST&I. In the case study, it was used an approach as tool to assess the implementation of open innovation projects. The results are shown several stages of open innovation project analyzed.  The study demonstrates the implications of open innovation project adoption to the strengthening of external networks and the maturing of the internal environment. The relevance of the study is based on the evaluation of an open innovation project in a public institution in order to foster the transition from traditional innovation processes to open innovation processes.

Main approaches to choice of decontamination methods in case of nuclear power plant shutdown

International Nuclear Information System (INIS)

Tarasov, V.M.; Syrkus, M.N.

1991-01-01

Selection criteria for optimal decontamination technology in case of nuclear power plant shutdown are considered. It is shown that technology evaluation from the viewpoint of observance of required precautionary measures is performed during the first stage of operation followed by analysis of process operational characteristics. The next stage relates to risk analysis of equipment, technological process and structure failures. The selection process is followed then according to criteria of decontamination duration, complexity level of control process and availability of qualified personnel, as well as complexity and composition of radioactive waste conditioning. Further follows decontamination technology evaluation from the viewpoint of its impact on personnal health and enviroment. Cost-benefit ratio resulting from introduction of technologies under consideration are determined at the final stage

Soil decontamination with Extraksol

International Nuclear Information System (INIS)

Paquin, J.; Mourato, D.

1989-01-01

The Extraksol process is a mobile decontamination technology which treats unconsolidated materials by solvent extraction. Treatment with Extraksol involves material washing, drying and solvent regeneration. Contaminant removal is achieved through desorption/dissolution mechanisms. The treated material is dry and acceptable to be reinstalled in its original location. The process provides a fast, efficient and versatile alternative for decontamination of soil and sludge. The organic contaminants extracted from the matrix are transferred to the extraction fluids. These are thereafter concentrated in the residues of distillation after solvent regeneration. Removal and concentration of the contaminants ensures an important waste volume reduction. This paper presents the process is operational principles and the steps involved in Extraksol's development with results of the pilot tests and full-scale demonstrations

Elucidate Innovation Performance of Technology-driven Mergers and Acquisitions

Energy Technology Data Exchange (ETDEWEB)

Huang, L.; Wang, K.; Yu, H.; Shang, L.; Mitkova, L.

2016-07-01

The importance and value of Mergers and Acquisitions (M&As) have increased with the expectancy to obtain key technology capabilities and rapid impact on innovation. This article develops an original analytical framework to elucidate the impact of the technology and product relatedness (similarity/complementarity) of the Technology-driven M&A’ partners on post-innovation performance. We present results drawing on a multiple case studies of Chinese High-Tech firms from three industries. (Author)

Innovative developments in uranium separation and concentration technology abroad

International Nuclear Information System (INIS)

Liang Jinlong; Zhou Mingsheng; Fang Wei; Sun Yuxiang

2014-01-01

Significance of deeply study the innovative developments in Uranium separation and concentration technology abroad was discussed. Development history and innovativeness of eight species of key equipments for separation and concentration were summarized for the first time. Principle and application of seven Uranium separation and concentration technology were analyzed systematically. It is expounded in the paper that high parameter, intelligent and low carbon were three development trends of Uranium separation and concentration technology. (authors)

Functions of Innovation Systems : A new approach for analysing technological change

NARCIS (Netherlands)

Hekkert, M.P.; Suurs, R.A.A.; Negro, Simona; Kuhlmann, Stefan; Smits, R.E.H.M.

2007-01-01

The central idea of this paper is that innovation systems are a very important determinant of technological change. We describe that the emergence of a new innovation system and changes in existing innovation systems co-evolve with the process of technological change. Therefore, it is necessary to

Volume reduction and material recirculation by freon decontamination

International Nuclear Information System (INIS)

Berners, O.; Buhmann, D.; Yamashita, Y.; Yoshiaki, M.

1989-01-01

This paper discusses the use of freon in a large variety of decontamination in the nuclear and non-nuclear fields. As far as the contamination is loose or smerable, surfaces of nearly all materials can be decontaminated. Freon is electrically non-conductive, chemically neutral and has a low surface tension. So it is capable of creeping under the contaminant and loosening or dissolving it. Used freon can be collected, cleaned and recirculated. Its cleaning can be done easily by evaporation at its lower vapor point of about 48 degrees C (104 degrees F). Good decontamination results could be achieved, expensive materials, tools and equipment could be recirculated. Big volumes of materials could get separated from their contaminants, which is the real radioactive waste. Freon decontamination is an effective, overall economical and approved technology to volume reduction and material recirculation

Imagining value, imagining users: academic technology transfer for health innovation.

Science.gov (United States)

Miller, Fiona Alice; Sanders, Carrie B; Lehoux, Pascale

2009-04-01

Governments have invested heavily in the clinical and economic promise of health innovation and express increasing concern with the efficacy and efficiency of the health innovation system. In considering strategies for 'better' health innovation, policy makers and researchers have taken a particular interest in the work of universities and related public research organizations: How do these organizations identify and transfer promising innovations to market, and do these efforts make best use of public sector investments? We conducted an ethnographic study of technology transfer offices (TTOs) in Ontario and British Columbia, Canada, to consider the place of health and health system imperatives in judgments of value in early-stage health innovation. Our analysis suggests that the valuation process is poorly specified as a set of task-specific judgments. Instead, we argue that technology transfer professionals are active participants in the construction of the innovation and assign value by 'imagining' the end product in its 'context of use'. Oriented as they are to the commercialization of health technology, TTOs understand users primarily as market players. The immediate users of TTOs' efforts are commercial partners (i.e., licensees, investors) who are capable of translating current discoveries into future commodities. The ultimate end users - patients, clinicians, health systems - are the future consumers of the products to be sold. Attention to these proximate and more distal users in the valuation process is a complex and constitutive feature of the work of health technology transfer. At the same time, judgements about individual technologies are made in relation to a broader imperative through which TTOs seek to imagine and construct sustainable innovation systems. Judgments of value are rendered sensible in relation to the logic of valuation for systems of innovation that, in turn, configure users of health innovation in systemic ways.

Determining Technological Innovation and Competitiveness: A Cross Organizational Analysis of the Malaysian Manufacturing Industry

Directory of Open Access Journals (Sweden)

Amlus Ibrahim

2012-01-01

Full Text Available This study analyzed the determinants of technological innovation in the Malaysian manufacturing industry. Its main purpose is to identify a set of management- related variables characterizing Malaysian innovative firms. Moreover, the study aimed to test whether the set of determinant differs for firms with different technological trajectories. A sample of 204 Malaysian firms was used for the investigation, with one respondent from each firm. The questionnaire measured the technological innovation, as well as 5 main potential determinants of innovation adopted from literature. Statistical analysis used, including bivariate correlation and multivariate regression, in identifying association between the technological innovation and the determining variables. The results of the analysis lead the researcher to the model of 5 important determining factors of technological innovation. The important factors were intensity of R&D, trvhnoogical trajectories,intensity of marketing, engineers, scientist and managers with experience locally and technical competency of personnel,. The analysis of technological trajectories confirmed the hypotheses that set of important determinants of innovation as well as the extent of technological innovation differs for firms in different innovation processes.Keywords: Technologies trajectories, technological innovation, intensity of R&D.

Application of Ultrasonic for Decontamination of Contaminated Soil - 13142

Energy Technology Data Exchange (ETDEWEB)

Vasilyev, A.P. [JRC ' NIKIET' , Moscow (Russian Federation); Lebedev, N.M. [LLC ' Aleksandra-Plus' , Vologda (Russian Federation); Savkin, A.E. [SUE SIA ' Radon' , Moscow (Russian Federation)

2013-07-01

The trials of soil decontamination were carried out with the help of a pilot ultrasonic installation in different modes. The installation included a decontamination bath equipped with ultrasonic sources, a precipitator for solution purification from small particles (less than 80 micrometer), sorption filter for solution purification from radionuclides washing out from soil, a tank for decontamination solution, a pump for decontamination solution supply. The trials were carried out on artificially contaminated sand with specific activity of 4.5 10{sup 5} Bk/kg and really contaminated soil from Russian Scientific Center 'Kurchatovsky Institute' (RSC'KI') with specific activity of 2.9 10{sup 4} Bk/kg. It was established that application of ultrasonic intensify the process of soil reagent decontamination and increase its efficiency. The decontamination factor for the artificially contaminated soil was ∼200 and for soil from RSC'KI' ∼30. The flow-sheet diagram has been developed for the new installation as well as determined the main technological characteristics of the equipment. (authors)

Innovative Technology Development Program. Final summary report

International Nuclear Information System (INIS)

Beller, J.

1995-08-01

Through the Office of Technology Development (OTD), the U.S. Department of Energy (DOE) has initiated a national applied research, development, demonstration, testing, and evaluation program, whose goal has been to resolve the major technical issues and rapidly advance technologies for environmental restoration and waste management. The Innovative Technology Development (ITD) Program was established as a part of the DOE, Research, Development, Demonstration, Testing, and Evaluation (RDDT ampersand E) Program. The plan is part of the DOE's program to restore sites impacted by weapons production and to upgrade future waste management operations. On July 10, 1990, DOE issued a Program Research and Development Announcement (PRDA) through the Idaho Operations Office to solicit private sector help in developing innovative technologies to support DOE's clean-up goals. This report presents summaries of each of the seven projects, which developed and tested the technologies proposed by the seven private contractors selected through the PRDA process

Using the regularities of high and critical technologies developing in innovative project management

Directory of Open Access Journals (Sweden)

S. G. Selivanov

2014-01-01

Full Text Available Problem-orientated to the innovative activity, computer-aided systems of production engineering (CASPE integrates design, manufacture, and organization activities using the interrelated innovation principles thus leaning the innovative activity towards the creation of innovative products and technological innovations of high science and technology level and efficiency. In this situation the innovative activity uses in practice not only the newest experience, but also the science laws and consequences, that is, in particular, “Science of Innovations”. The mentioned science laws explain wave dynamics of technical (technological systems development. In the course of innovation activities and/or innovation designing a modification of continuously acting technological system, usually, causes its developing and growing upwards by Sshaped curve. Changing a principle of action changes S-shaped curve development (Fig. 1. If such changes are within the certain “trace tube” we are entitled to state the steady system development.Analysis of changing target function of technological system within the “trace tube” of its steady development characterizes its growing wave dynamics (Fig. 1 using the S-shaped curves (sigmoid type relations. S-shaped innovative development relations of technological systems are, usually, explained by different mathematical models, each being in compliance with the certain process of science and technology. Singular innovative project management using the S-shaped curves can be explained by the following example (Fig.2.To use such management technique it is very important to know the mathematical models of S-curves for different types of innovation projects. That is why we consider given S-shaped relations in-detail for:- developing the high and critical technologies during R&D implementation using the cutting-edge CASSR (computer-aided systems of scientific research of high and critical technologies in innovation

Decontamination

International Nuclear Information System (INIS)

Montford, B.

1975-01-01

Development of special techniques has permitted the use of mild decontamination processes for the CANDU type reactor primary coolant circuit, overcoming many of the problems associated with conventional decontamination processes, which use strong, acidic reagents. (Author)

Reactor component chemical decontamination-developments in waste handling and disposal

International Nuclear Information System (INIS)

Papesch, R.; Atwood, K.L.

1989-01-01

Because of restrictive limits on man-rem exposure in European nuclear plants, a company has developed and applied a number of chemical decontamination techniques for components that must be periodically maintained. These techniques are particularly effective for components that can be placed in a decontamination bath for dose reduction prior to performing maintenance. The cleaning technique has the ability to achieve decontamination factors of at least 20 and in some cases much greater. For components with before cleaning dose rates of between 1 to as high as 80 R/hr, significant man-rem reductions are achieved when hundreds of manhours may be required to complete required component maintenance. Transferring this solvent technology to the U.S. required a program to develop solidification formulas to allow the solvent wastes to be disposed of in accordance with regulations and in a cost effective manner. This paper demonstrates in chemical decontaminations with small liquid volume systems that concentrated decontamination solvents can be employed to achieve high decontamination factors

Technological Innovation – A Route Towards Sustainability

Directory of Open Access Journals (Sweden)

Gráinne Kavanagh

2012-06-01

Full Text Available The sustainability of small and medium-sized enterprises (SMEs  is constantly challenged on today’s dynamic operating environment. Evolving regulatory trends, difficult economic conditions, and diminishing natural resources, pose serious questions for all players across the food system. Technological innovation, as a means of ensuring future sustainability in the same in the face of such challenges, has been the focus of significant government investment in Ireland. This paper, aims to facilitate a greater understanding of the motivations and barriers influencing the decision by food SMEs to invest in technological innovation emanating from research conducted in publicly‐funded research institutes.

Water Technology Innovation: 10 Market Opportunities

Science.gov (United States)

The Water Technology Innovation Blueprint offers an overview of market opportunities that include conserving and recovering energy, recovering nutrients, improving water infrastructure, reducing costs for water monitoring, and improving water quality.

Decoupling management and technological innovations: Resolving the individualism-collectivism controversy

OpenAIRE

Cerne, Matej; Jaklic, Marko; Skerlavaj, Miha

2013-01-01

This is the authors' final and accepted version of the article, post refereeing. Publisher's version is available at www.sciencedirect.com This study aims to resolve the contradictory previous research findings on the relationship between individualism–collectivism and innovation. We draw on innovation theory and relate to the difference between non-technological (management) and technological innovation types as well as to the distinction between exploration and exploitation (inv...

Challenges to the Indicators on Science, Technology and Innovation Development

OpenAIRE

Chobanova, Rossitsa

2006-01-01

The paper attempts to define the challenges to the indicators on science, technology and innovation development which result from the contemporary dynamics of the global knowledge based economy progress and the pursued challenges of identification of the specific national priority dimensions for public funding research and innovation projects on the case of Bulgaria. It is argued that recent the most widespread methodologies of positioning science, technology and innovation indicators do not ...

Governing Science, Technology and Innovation:

DEFF Research Database (Denmark)

Jensen, Jens Stissing

2007-01-01

Abstract: As an object of public management, Science, Technology and Innovation (STI) is characterised by a high level of uncertainty and complexity. The paper argues that to cope with the phenomenon of STI as a coherent area of policy formulation and regulation, a balancing of rational-, reflexi...

Mixed waste characterization, treatment, and disposal focus area. Technology summary

International Nuclear Information System (INIS)

1995-06-01

This paper presents details about the technology development programs of the Department of Energy. In this document, waste characterization, thermal treatment processes, non-thermal treatment processes, effluent monitors and controls, development of on-site innovative technologies, and DOE business opportunities are applied to environmental restoration. The focus areas for research are: contaminant plume containment and remediation; mixed waste characterization, treatment, and disposal; high-level waste tank remediation; landfill stabilization; and decontamination and decommissioning

Mixed waste characterization, treatment, and disposal focus area. Technology summary

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

This paper presents details about the technology development programs of the Department of Energy. In this document, waste characterization, thermal treatment processes, non-thermal treatment processes, effluent monitors and controls, development of on-site innovative technologies, and DOE business opportunities are applied to environmental restoration. The focus areas for research are: contaminant plume containment and remediation; mixed waste characterization, treatment, and disposal; high-level waste tank remediation; landfill stabilization; and decontamination and decommissioning.

COMPILATION OF AVAILABLE DATA ON BUILDING DECONTAMINATION ALTERNATIVES

Science.gov (United States)

The report presents an analysis of selected technologies that have been tested for their potential effectiveness in decontaminating a building that has been attacked using biological or chemical warfare agents, or using toxic industrial compounds. The technologies selected to be ...

Technological development toward nuclear reactor decommissioning. Utilization of 3D measurement data (6D CAD™) and system decontamination (T-OZON™)

International Nuclear Information System (INIS)

Hotta, Koji; Hatakeyama, Makoto

2016-01-01

Toshiba Corporation has been developing the technologies related to decommissioning for more than 30 years, and making them into practical use. This paper introduced 6D CAD™, which applies the CAD system that is effective for rational planning at the initial stage and effective for managing the progress of construction work, as well as T-OZON™ method, which is effective for reducing the exposure of construction workers. This 6D CAD™ can deal with the following items necessary for decommissioning work: (1) decommissioning management such as schedule control and yearly exposure dose management, (2) management such as planning and implementation of procedures, as well as waste management and traceability, and (3) essential technologies such as the optimization of dismantling plan, reduction in processing/disposal cost, database construction for engineering information, measurement of reactor inside, and measurement of radiation dose and database construction of its information. T-OZON™ method is a chemical decontamination technology that can be applied to pre-demolition decontamination aimed at reducing the exposure of workers and reducing the amount of radioactive materials in the dust generated during dismantling work, and greatly reducing the secondary waste originated from used chemicals. Oxalic acid is used as a reducing agent, and ozone water is used as an oxidizing agent. This method has been applied over 200 times mainly for BWR. The application to PWR has been tested by experiments, and prospects for achieving the target value for decontamination have been obtained for both materials of SUS 304 and Alloy 600. (A.O.)

On the problem of radiation decontamination of the domestic sewage sludge

International Nuclear Information System (INIS)

Arbuzova, N.A.

1978-01-01

Soviet and foreign investigations on decontamination of drinking, natural, and waste waters with the use of gamma radiation are surveyed. A comparative analysis of data published on radiation decontamination showed that most experimental investigations were carried out on artificially prepared suspensions of microorganisms. The value of such investigations lies in the fact that they give the representation on the relative radiosensitivity of microorganisms in and aqueous medium and enable one to establish the effect of some physicochemical factors on the efficiency of radiation decontamination. Nevertheless, the results of the investigations carried out in this direction do not fully reflect actual conditions at existing decontamination stations and connot serve as a basis for estimating the technological and economic efficiency of the radiation decontamination method

Development and design application of cerium (IV) decontamination process

International Nuclear Information System (INIS)

Bray, L.A.; Seay, J.M.

1988-01-01

A simple and effective method was developed for decontamination of high-level waste canisters. This method of chemical decontamination is applicable to a wide variety of contaminated equipment found in the nuclear industry. Conceptual design of the cerium [Ce(IV)] decontamination process equipment has been completed for the West Valley Demonstration project (WVDP) vitrification facility. This remote equipment, which is the first engineering scale application of this technology, will remove surface contamination from stainless-steel (SS) containers containing high-level waste (HLW) glass prior to placing them into temporary storage and ultimate shipment to a U.S. Department of Energy (DOE) repository for disposal. The objective of the development and design study was to identify an effective chemical process and to design equipment to decontaminate the HLW glass canisters to limits that meet U.S. DOE requirements. The equipment includes canister-capping and smear stations in addition to the decontamination module and associated services

Development and design application of cerium (IV) decontamination process

International Nuclear Information System (INIS)

Bray, L.A.; Seay, J.M.

1988-10-01

A simple and effective method was developed for decontamination of high-level waste canisters. This method of chemical decontamination is applicable to a wide variety of contaminated equipment found in the nuclear industry. Conceptual design of the cerium [Ce(IV)] decontamination process equipment has been completed for the West Valley Demonstration Project (WVDP) vitrification facility. This remote equipment, which is the first engineering scale application of this technology, will remove surface contamination from stainless-steel (SS) containers containing high-level waste (HLW) glass prior to placing them into temporary storage and ultimate shipment to a US Department of Energy (DOE) repository for disposal. The objective of the development and design study was to identify an effective chemical process and to design equipment to decontaminate the HLW glass canisters to limits that meet USDOE requirements. The equipment includes canister-capping and smear stations in addition to the decontamination module and associated services. 2 refs., 1 fig