Boron-based nanostructures: Synthesis, functionalization, and characterization

Science.gov (United States)

Bedasso, Eyrusalam Kifyalew

Boron-based nanostructures have not been explored in detail; however, these structures have the potential to revolutionize many fields including electronics and biomedicine. The research discussed in this dissertation focuses on synthesis, functionalization, and characterization of boron-based zero-dimensional nanostructures (core/shell and nanoparticles) and one-dimensional nanostructures (nanorods). The first project investigates the synthesis and functionalization of boron-based core/shell nanoparticles. Two boron-containing core/shell nanoparticles, namely boron/iron oxide and boron/silica, were synthesized. Initially, boron nanoparticles with a diameter between 10-100 nm were prepared by decomposition of nido-decaborane (B10H14) followed by formation of a core/shell structure. The core/shell structures were prepared using the appropriate precursor, iron source and silica source, for the shell in the presence of boron nanoparticles. The formation of core/shell nanostructures was confirmed using high resolution TEM. Then, the core/shell nanoparticles underwent a surface modification. Boron/iron oxide core/shell nanoparticles were functionalized with oleic acid, citric acid, amine-terminated polyethylene glycol, folic acid, and dopamine, and boron/silica core/shell nanoparticles were modified with 3-(amino propyl) triethoxy silane, 3-(2-aminoethyleamino)propyltrimethoxysilane), citric acid, folic acid, amine-terminated polyethylene glycol, and O-(2-Carboxyethyl)polyethylene glycol. A UV-Vis and ATR-FTIR analysis established the success of surface modification. The cytotoxicity of water-soluble core/shell nanoparticles was studied in triple negative breast cancer cell line MDA-MB-231 and the result showed the compounds are not toxic. The second project highlights optimization of reaction conditions for the synthesis of boron nanorods. This synthesis, done via reduction of boron oxide with molten lithium, was studied to produce boron nanorods without any

Synthesis and Characterization of Some New Thermal Stable Polymers - Polymerization of N-[4-N´ -(Benzylamino-carbonylphenyl]maleimide

Directory of Open Access Journals (Sweden)

B. L. Hiran

2007-01-01

Full Text Available This article describes the synthesis and characterization of homopolymer (H-BCPM of N-[4-N'-(benzylamino-carbonyl phenyl] maleimide (N-BACPMI and copolymer (C-BCPM of N-BACPMI with n-butyl acrylate (BA. The new monomer was synthesized from p-aminobenzoic acid, maleic anhydride and benzylamine. The homopolymerization of N-BACPMI is initiated by free radical using AIBN in THF solvent at 65°C. Radical copolymerization of N-BACPMI with BA, initiated by AIBN, was performed in THF solvent using equimolar amount. Effect of the different free radical initiator AIBN, BPO and solvents p-Dioxane, THF, DMF and DMSO was studied. Homopolymer and Copolymer were characterized by intrinsic viscosity, solubility test, FT-IR, 1H-NMR spectral analysis and elemental analysis. Thermal behaviour was studied by Thermo gravimetric analysis.

Synthesis, Spectroscopic and DFT Characterization of 4â-(4-tert ...

African Journals Online (AJOL)

In this work the synthesis, spectral characterization and non-linear optical properties of metal-free .... following literature methods23–26 The advantage of this method ..... Synthesis of phthalocyanine conjugates with gold nanoparticles and.

Nanoscale Synthesis and Characterization Laboratory Annual Report 2005

Energy Technology Data Exchange (ETDEWEB)

Hamza, A V; Lesuer, D R

2006-01-03

The Nanoscale Synthesis and Characterization Laboratory's (NSCL) primary mission is to create and advance interdisciplinary research and development opportunities in nanoscience and technology. The initial emphasis of the NSCL has been on development of scientific solutions in support of target fabrication for the NIF laser and other stockpile stewardship experimental platforms. Particular emphasis has been placed on the design and development of innovative new materials and structures for use in these targets. Projects range from the development of new high strength nanocrystalline alloys to graded density materials to high Z nanoporous structures. The NSCL also has a mission to recruit and train personnel for Lab programs such as the National Ignition Facility (NIF), Defense and Nuclear Technologies (DNT), and Nonproliferation, Arms control and International security (NAI). The NSCL continues to attract talented scientists to the Laboratory.

Synthesis and characterization of dextran-coated iron oxide nanoparticles

Science.gov (United States)

Predescu, Andra Mihaela; Matei, Ecaterina; Berbecaru, Andrei Constantin; Pantilimon, Cristian; Drăgan, Claudia; Vidu, Ruxandra; Predescu, Cristian; Kuncser, Victor

2018-03-01

Synthesis and characterization of iron oxide nanoparticles coated with a large molar weight dextran for environmental applications are reported. The first experiments involved the synthesis of iron oxide nanoparticles which were coated with dextran at different concentrations. The synthesis was performed by a co-precipitation technique, while the coating of iron oxide nanoparticles was carried out in solution. The obtained nanoparticles were characterized by using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction spectrometry, Fourier transform infrared spectroscopy and superconducting quantum interference device magnetometry. The results demonstrated a successful coating of iron oxide nanoparticles with large molar weight dextran, of which agglomeration tendency depended on the amount of dextran in the coating solution. SEM and TEM observations have shown that the iron oxide nanoparticles are of about 7 nm in size.

Synthesis and characterization of magnetite nanoparticles coated with lauric acid

Energy Technology Data Exchange (ETDEWEB)

Mamani, J.B., E-mail: javierbm@einstein.br [Instituto do Cérebro-InCe, Hospital Israelita Albert Einstein-HIAE, 05651-901 São Paulo (Brazil); Costa-Filho, A.J. [Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, Universidade de São Paulo, Ribeirão Preto (Brazil); Cornejo, D.R. [Instituto de Física Universidade de São Paulo, USP, São Paulo (Brazil); Vieira, E.D. [Instituto de Física, Universidade Federal de Goiás, Goiânia (Brazil); Gamarra, L.F. [Instituto do Cérebro-InCe, Hospital Israelita Albert Einstein-HIAE, 05651-901 São Paulo (Brazil)

2013-07-15

Understanding the process of synthesis of magnetic nanoparticles is important for its implementation in in vitro and in vivo studies. In this work we report the synthesis of magnetic nanoparticles made from ferrous oxide through coprecipitation chemical process. The nanostructured material was coated with lauric acid and dispersed in aqueous medium containing surfactant that yielded a stable colloidal suspension. The characterization of magnetic nanoparticles with distinct physico-chemical configurations is fundamental for biomedical applications. Therefore magnetic nanoparticles were characterized in terms of their morphology by means of TEM and DLS, which showed a polydispersed set of spherical nanoparticles (average diameter of ca. 9 nm) as a result of the protocol. The structural properties were characterized by using X-ray diffraction (XRD). XRD pattern showed the presence of peaks corresponding to the spinel phase of magnetite (Fe{sub 3}O{sub 4}). The relaxivities r{sub 2} and r{sub 2}* values were determined from the transverse relaxation times T{sub 2} and T{sub 2}* at 3 T. Magnetic characterization was performed using SQUID and FMR, which evidenced the superparamagnetic properties of the nanoparticles. Thermal characterization using DSC showed exothermic events associated with the oxidation of magnetite to maghemite. - Highlights: • Synthesis of magnetic nanoparticles coated with lauric acid • Characterization of magnetic nanoparticles • Morphological, structural, magnetic, calorimetric and relaxometric characterization.

Synthesis and characterization of rare-earth-doped calcium tungstate nanocrystals

Science.gov (United States)

Suneeta, P.; Rajesh, Ch.; Ramana, M. V.

2018-02-01

In this paper, we report synthesis and characterization of rare-earth-ion-doped calcium tungstate (CaWO4) nanocrystals (NCs). Rare-earth ions, such as gadolinium (Gd), neodymium (Nd), praseodymium (Pr), samarium (Sm) and holmium (Ho), were successfully doped in the CaWO4 NCs by changing the synthesis conditions. The adopted synthesis route was found to be fast and eco-friendly. Structural characterizations, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and compositional analysis, were performed using energy dispersive analysis of X-rays (EDAX) on as-synthesized NCs. The results indicate the size of the NCs ranging between 47 to 68nm and incorporation of rare-earth ions in CaWO4 NCs.

Synthesis, characterization, thermal

Directory of Open Access Journals (Sweden)

Selma Bal

2017-09-01

Full Text Available This work explains the synthesis of a new azo-Schiff base compound, derived from condensation between N-ethylcarbazole-3-carbaldehyde and 1,3-diaminopropane, followed by azo coupling reaction with the diazonium salt of 2-amino-4-methyl phenol. The newly synthesized azo-Schiff base was further reacted with the acetate salts of Copper, Cobalt and Nickel to give three coordination compounds. All synthesized compounds have been characterized through spectral analysis. The coordination compounds have been examined for their thermal and catalytic features. Good and moderate yields were obtained for the oxidation of styrene and cyclohexene. Thermal features of the ligand and its complexes have been explained and the results obtained have supported the proposed structures.

Synthesis, characterization and electrospinning of corn cob cellulose-graft-polyacrylonitrile and their clay nanocomposites.

Science.gov (United States)

Kalaoğlu, Özlem I; Ünlü, Cüneyt H; Galioğlu Atıcı, Oya

2016-08-20

This study aims at evaluation of cellulose recovered from agricultural waste (corn cob) in terms of synthesis of graft copolymers, polymer/clay nanocomposites, and nanofibers. The copolymers and nanocomposites were synthesized in aqueous solution using Ce(4+) initiator. Conditions (concentrations of the components, reaction temperature, and period) were determined first for copolymer synthesis to obtain the highest conversion ratio. Then found parameters were used to synthesize nanocomposites adding clay mineral to reaction medium. Although there was a decrease in conversion in nanocomposites syntheses, thermal and rheologic measurements indicated enhancements compared to pristine copolymer. Obtained polymeric materials have been successfully electrospun into nanofibers and characterized. Average diameter of the nanofibers was about 650nm and was strongly influenced by NaMMT amount in the nanocomposite sample. Copyright © 2016 Elsevier Ltd. All rights reserved.

The effect of heat and radiation on the initiation and elongation processes of DNA synthesis

International Nuclear Information System (INIS)

Davies, R.C.; Bowden, G.T.; Cress, A.E.

1983-01-01

The pH step alkaline elution and alkaline sucrose gradient techniques were utilized to evaluate alterations in DNA replication (initiation and elongation) induced by heat and low dose X-irradiation in synchronized Chinese hamster ovary cells. The initiation and elongation processes of DNA synthesis were radioresistant at the G 1 /S boundary (4 hours after mitosis) while in mid S phase (9 hours after mitosis) DNA initiation and elongation were sensitive to X-irradiation. The initiation and elongation processes of DNA synthesis which were radiation resistant at the G 1 /S boundary could be inhibited by a hyperthermia treatment (43 0 C for 1 hour beginning at 4 hours after mitosis). The impairment of initiation in the heated cells was maintained through late S phase while that of elongation was reversible as judged by full recovery at 15 hours after mitosis. These data suggest that the known synergistic lethality of heat and radiation may be mediated by an impairment of initiation of DNA synthesis. (author)

Synthesis, characterization and antimicrobial activity of mixed ...

African Journals Online (AJOL)

Synthesis, characterization and antimicrobial activity of mixed ascorbic acid - nicotinamide metal complexes. ... The result of the antimicrobial studies showed that the mixed complexes have higher inhibitory activity than the original ligands against the tested bacteria and fungi species. KEY WORDS: Ascorbic acid, ...

Green synthesis, characterization and antibacterial activity of copper ...

African Journals Online (AJOL)

Green synthesis, characterization and antibacterial activity of copper nanoparticles using L -ascorbic ... Journal Home > Vol 10, No 3 (2017) > ... In this study, simple, economical, convenient and environmentally-friendly chemical reduction ...

Synthesis, Characterization and Applications in Catalysis of Polyoxometalate/Zeolite Composites

Directory of Open Access Journals (Sweden)

Frédéric Lefebvre

2016-05-01

Full Text Available An overview of the synthesis, characterization and catalytic applications of polyoxometalates/zeolites composites is given. The solids obtained by direct synthesis of the polyoxometalate in the presence of the zeolite are first described with their applications in catalysis. Those obtained by a direct mixing of the two components are then reviewed. In all cases, special care is taken in the localization of the polyoxometalate, inside the zeolite crystal, in mesopores or at the external surface of the crystals, as deduced from the characterization methods.

Protein synthesis during the initial phase of the temperature-induced bleaching response in Euglena gracilis

International Nuclear Information System (INIS)

Ortiz, W.

1990-01-01

Growing cultures of photoheterotrophic Euglena gracilis experience an increase in chlorophyll accumulation during the initial phase of the temperature-induced bleaching response suggesting an increase in the synthesis of plastid components at the bleaching temperature of 33 degree C. A primary goal of this work was to establish whether an increase in the synthesis of plastid proteins accompanies the observed increase in chlorophyll accumulation. In vivo pulse-labeling experiments with [ 35 S]sodium sulfate were carried out with cells grown at room temperature or at 33 degree C. The synthesis of a number of plastid polypeptides of nucleocytoplasmic origin, including some presumably novel polypeptides, increased in cultures treated for 15 hours at 33 degree C. In contrast, while synthesis of thylakoid proteins by the plastid protein synthesis machinery decreased modestly, synthesis of the large subunit of the enzyme ribulosebisphosphate carboxylase was strongly affected at the elevated temperature. Synthesis of novel plastid-encoded polypeptides was not induced at the bleaching temperature. It is concluded that protein synthesis in plastids declines during the initial phase of the temperature response in Euglena despite an overall increase in cellular protein synthesis and an increase in chlorophyll accumulation per cell

Synthesis and characterization of the Cu2ZnSnS4 system for photovoltaic applications

Science.gov (United States)

Sánchez Pinzón, D. L.; Soracá Perez, G. Y.; Gómez Cuaspud, J. A.; López, E. Vera

2017-01-01

This paper focuses on the synthesis and characterization of a ceramic material based on the Cu2ZnSnS4 system, through the implementation of a hydrothermal route. For this purpose, we started from nitrate dissolutions in a 1.0mol L-1 concentration, which were mixed and treated in a teflon lined vessel steel at 280°C for 48h. The Physicochemical characterization of the solid was evaluated by means of ultraviolet visible spectroscopy (UV-VIS), X-ray diffraction (XRD), Raman spectroscopy, scanning and transmission electron microscopy (SEM-TEM) and solid state impedance spectroscopy (IS). The initial characterization through UV measurements confirms a Band-gap around 1.46eV obtained by the Kubelka-Munk method, which demonstrates the effectiveness of the synthesis method in the obtaining of a semiconductor material. The XRD results confirm the obtaining of a crystalline material of pure phase with tetragonal geometry and I-42m space group. The preferential crystalline orientation was achieved along (2 2 0) facet, with crystallite sizes of nanometric order (6.0nm). The morphological aspects evaluated by means electron microscopy, confirmed the homogeneity of the material, showing specifically a series of textural and surface properties of relevant importance. Finally, the electrical characterizations allow to validate the semiconductor behaviour of CZTS system for development of photovoltaic technologies.

Hyperbranched Polyethylenebased Macromolecular Architectures: Synthesis, Characterization, and Selfassembly

KAUST Repository

Al-Sulami, Ahlam

2018-01-01

-b-PNIPAM, and hyperbranched polyethylene-b-poly(solketal acrylate), HBPE-b-PSA, were successfully synthesized by combining CWCP and ATRP. The synthetic methodology includes the following steps; a) synthesis of multifunction hyperbranched polyethylene initiators HBPE

Synthesis, characterization and behaviour of trans-bis (argininate) copper (II) to gamma radiation

International Nuclear Information System (INIS)

Pereira, A.B.

1984-01-01

The synthesis, the characterization and the behaviour to gamma radiation of trans-bis (argininate) copper (II) are presented. The synthesis is made from copper sulfate, sodium hydroxide and hydrochloride of L (+) arginine, in aqueous medium, and the characterization by infrared spectroscopy, visible and ultraviolet spectroscopy and elementary analysis. (C.G.C.)

Synthesis and characterization of organically linked ZnO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Chory, Christine; Riedel, Ingo; Parisi, Juergen [Energy and Semiconductor Research Laboratory (EHF), University of Oldenburg, Carl-von Ossietzky-Strasse 9-11, 26129 Oldenburg (Germany); Kruska, Carsten; Heimbrodt, Wolfram [Department of Physics and Material Sciences Center, Philipps-University Marburg, Renthof 5, 35032 Marburg (Germany); Feser, Clemens [NEXT ENERGY - EWE Research Centre for Energy Technology e.V., Carl-von Ossietzky-Strasse 15, 26129 Oldenburg (Germany); Beenken, Wichard J.D. [Department of Theoretical Physics I, Ilmenau University of Technology, Weimarer Strasse 25, 98693 Ilmenau (Germany); Hoppe, Harald [Department of Experimental Physics I, Ilmenau University of Technology, Weimarer Strasse 32, 98693 Ilmenau (Germany)

2012-11-15

We report on the solution-based synthesis and characterization of three-dimensional networks of ZnO nanoparticles where the formation of structures is achieved by covalently linking the nanocrystals with bifunctional organic ligands. The colloidal synthesis will be presented with application of two ligands that vary in size and binding sites. Furthermore we report on structural characterization of dried powders and thin films by means of X-ray diffraction and electron microscopy in order to examine the regularity of the structures. We also present first investigations of the optical properties and electrical conductance behavior in lateral direction of the differently linked hybrid ZnO networks. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Synthesis and characterization of organically linked ZnO nanoparticles

International Nuclear Information System (INIS)

Chory, Christine; Riedel, Ingo; Parisi, Juergen; Kruska, Carsten; Heimbrodt, Wolfram; Feser, Clemens; Beenken, Wichard J.D.; Hoppe, Harald

2012-01-01

We report on the solution-based synthesis and characterization of three-dimensional networks of ZnO nanoparticles where the formation of structures is achieved by covalently linking the nanocrystals with bifunctional organic ligands. The colloidal synthesis will be presented with application of two ligands that vary in size and binding sites. Furthermore we report on structural characterization of dried powders and thin films by means of X-ray diffraction and electron microscopy in order to examine the regularity of the structures. We also present first investigations of the optical properties and electrical conductance behavior in lateral direction of the differently linked hybrid ZnO networks. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Synthesis and characterization of germa[n]pericyclynes.

Science.gov (United States)

Tanimoto, Hiroki; Nagao, Tomohiko; Nishiyama, Yasuhiro; Morimoto, Tsumoru; Iseda, Fumiyasu; Nagato, Yuko; Suzuka, Toshimasa; Tsutsumi, Ken; Kakiuchi, Kiyomi

2014-06-14

The synthesis and characterization of novel pericyclynes comprising germanium atoms and acetylenes, germa[n]pericyclynes, are described. The prepared germa[4]-, [6]-, and [8]pericyclynes were compared by (13)C NMR spectroscopy, X-ray crystallography, cyclic voltammetry, UV-visible spectroscopy, fluorescence emission spectroscopy, Raman spectroscopy, and density functional theory calculation analyses.

Synthesis & Characterization of New bis-Symmetrical Adipoyl ...

African Journals Online (AJOL)

Full Title: Synthesis and Characterization of New bis-Symmetrical Adipoyl, Terepthaloyl, Chiral Diimido-di-L-alanine Diesters and Chiral Phthaloyl-L-alanine Ester of Tripropoxy p-tert-Butyl Calix[4]arene and Study of Their Hosting Ability for Alanine and Na+. Bis-symmetrical tripropoxy p-tert-butyl calix[4]arene esters were ...

Synthesis and structural characterization of a calcium coordination ...

Indian Academy of Sciences (India)

Synthesis and structural characterization of a calcium coordination polymer based on a μ3-bridging. tetradentate binding mode of glycine. SUBRAMANIAN NATARAJAN*a, BIKSHANDARKOIL R. SRINIVASANb , J. KALYANA SUNDARa, K. RAVIKUMARc , R.V. KRISHNAKUMARd , J. SURESHe,. aSchool of Physics, ...

Polypyrrole-silver Nanocomposite: Synthesis and Characterization

OpenAIRE

D. M. Nerkar; S. V. Panse; S. P. Patil; S. E. Jaware; G. G. Padhye

2016-01-01

Polypyrrole-Silver (PPy-Ag) nanocomposite has been successfully synthesized by the chemical oxidative polymerization of pyrrole with iron (III) chloride as an oxidant, in the presence of a colloidal suspension of silver nanoparticles. Turkevich method (Citrate reduction method) was used for the synthesis of silver nanoparticles (Ag NPs). The silver nanoparticles were characterized by UV-Visible spectroscopy which showed an absorption band at 423 nm confirming the formation of nanoparticles. P...

Synthesis and characterization of activated lithium fluoride with silver

International Nuclear Information System (INIS)

Encarnacion E, E. K.; Guerrero S, Z.; Reyes A, J.

2017-10-01

The present work shows part of the results obtained in the development of the research that has been carried out since 2015 entitled -Synthesis and characterization of new thermoluminescent materials for the radiation dosimetry and its applications in health-. In the development of this research, the synthesis of crystals of pure lithium fluoride (LiF) and activated with different concentrations of silver (LiF:Ag); synthesized samples are also presented using different temperatures, as well as varying the concentration of the solvent (water-ethanol). The synthesized materials were characterized through different techniques: scanning electron microscopy and X-ray diffraction. Specifically, the results of the calculation of the size of the LiF crystals are presented using the Scherrer equation. Within the results, a dependence on the size of the crystals is highlighted by means of the following factors: the amount of activator in the sample, the temperature at which the sample was synthesized, as well as the amount of solvent in the synthesis. The samples have a simple cubic crystalline phase. (Author)

SYNTHESIS AND CHARACTERIZATION OF N, N'-BIS-(3 ...

African Journals Online (AJOL)

user

base complexes derived from Salicylaldehyde and histidine with some divalent transition metal ions. Furthermore, Syed (1993) reported the synthesis, characterization and biological evaluation of some. Schiff base metal complexes derived from Anthranilic acid-sugar and naturally occurring amino acid-sugar. Schiff bases ...

Synthesis and characterization of reactive dye-cassava mesocarp ...

African Journals Online (AJOL)

The synthesis of triazine based reactive dyes was carried out. The resultant dyes were characterized by thin layers chromatography, molecular weight, infrared and ultra- violet spectroscopy, and used in dyeing cassava mesocarp to produce dye modified cellulosic substrates. The dyed substrates were tested for dye fixation, ...

Synthesis and characterization of new optically active poly(amide ...

African Journals Online (AJOL)

Synthesis and characterization of new optically active poly(amide-imide)s based on N -trimellitimido- ... Bulletin of the Chemical Society of Ethiopia ... (DMAc), dimethyl sulfoxide (DMSO) and N-methyl-2-pyrrolidone (NMP) at room temperature.

Synthesis, structural and electrical characterizations of thermally ...

African Journals Online (AJOL)

Synthesis, structural and electrical characterizations of thermally evaporated Cu 2 SnS 3 thin films. ... The surface profilometer shows that the deposited films are rough. The XRD spectra identified the ... The electrical resistivity of the deposited Cu2SnS3 film is 2.55 x 10-3 Ωcm. The conductivity is in the order of 103 Ω-1cm-1.

Combustion synthesis and structural characterization of Li–Ti mixed

Indian Academy of Sciences (India)

Combustion synthesis and structural characterization of Li–Ti mixed nanoferrites ... were prepared by combustion method at lower temperatures compared to the ... first time at low temperatures, using PEG which acts as a new fuel and oxidant.

Synthesis, characterization and magnetic properties of selected Laves and MAX phases

International Nuclear Information System (INIS)

Hamm, Christin Maria

2017-01-01

In this work the rare-earth free Laves phases Ti 2 M 3 Si with M = Mn, Fe, Co, Ni were synthesized by microwave heating and were structurally and magnetically characterized. Furthermore, the solid solution Ti 2 (Co 1-x Fe x ) 3 Si was synthesized by arc melting and spark plasma sintering, as well as their magnetic behavior was studied. In addition to the Laves phases, the focus was on the synthesis and characterization of aluminum-based MAX phases. For the first time the ternary carbides were prepared by microwave heating. The phase-pure representation of MAX phases was particularly challenging for synthetic solid-state chemistry. The susceptor-assisted microwave heating allows the synthesis of high-quality samples, which was shown in this work on M 2 AlC (M = Ti, V, Cr) and V 4 AlC 3 . Furthermore, for the first time, the doping of these materials with Mn and Fe was successful. In addition to the structural characterization of the new phases, the microstructure and magnetic properties are discussed in this work. Using these doped compounds as well as the compound V 4 AlC 3 , it has been shown that field-activated synthesis, particularly susceptor-assisted microwave heating, are a very good synthesis method for compounds which are hard or sometimes not synthesized by conventional methods.

Methods for initial characterization of Campylobacter jejuni bacteriophages

DEFF Research Database (Denmark)

Sørensen, Martine Camilla Holst; Gencay, Yilmaz Emre; Brøndsted, Lone

2017-01-01

Here we describe an initial characterization of Campylobacter jejuni bacteriophages by host range analysis, genome size determination by pulsed-field gel electrophoresis, and receptor-type identification by screening mutants for phage sensitivity.......Here we describe an initial characterization of Campylobacter jejuni bacteriophages by host range analysis, genome size determination by pulsed-field gel electrophoresis, and receptor-type identification by screening mutants for phage sensitivity....

Synthesis of Fe–Ni bimetallic nanoparticles from pixel target ablation: plume dynamics and surface characterization

International Nuclear Information System (INIS)

Niu Xiaoxu; Murray, Paul T.; Sarangan, Andrew

2012-01-01

A novel Fe–Ni bimetallic nanoparticle synthesis technique, denoted pixel target ablation, is reported. The technique entails ablating a thin film target consisting of patterned Fe and Ni pixels with a selected ratio using a KrF excimer laser. The laser energy breaks a known amount of target materials into metal atoms, which then form nanoparticles by recombination in the gas phase. Due to the nature of thin-film ablation, splashing of large particles was eliminated with the added benefit of minimizing nanoparticle agglomeration. Plume dynamics and surface characterizations were carried out to exploit the formation of Fe–Ni nanoparticles more fully. The composition was readily controlled by varying the initial relative amount of Fe and Ni target pixels. Synthesis of multi-element nanoparticles by pixel target ablation should be possible with any element combination that can be prepared as a thin-film target.

Synthesis and characterization of cadmium doped lead–borate ...

Indian Academy of Sciences (India)

Unknown

Mater. Sci., Vol. 29, No. 1, February 2006, pp. 55–58. © Indian Academy of Sciences. 55. Synthesis and characterization of cadmium doped lead–borate glasses. A A ALEMI*, H SEDGHI†, A R MIRMOHSENI and V GOLSANAMLU. Department of Inorganic Chemistry, Faculty of Chemistry, University of Tabriz, Tabriz, Iran.

Synthesis and characterization of magnetite nanoparticles encapsulated in a bovine hemoglobin microgel

Science.gov (United States)

Mody, Puja J.

This study shows the successful synthesis and characterization of a novel material that is composed of iron oxide particles within a protein gel. During the synthesis, bovine hemoglobin surrounds the forming Fe 3O4 nanoparticles, resulting in a biocompatible hydrogel, which has the potential to be used as a targeted drug delivery vehicle and as an MRI contrast agent. The structure, size, and thermal stability of these hydrogel complexes were analyzed using a range of techniques. Powder x-ray diffraction and infrared spectroscopy indicated the presence of Fe3O 4 and hemoglobin without significant interactions between particles in the solid state. Microscopy analysis determined the average size of these microgel complexes to be 4-9 mum2 in area (˜2-3 mum in diameter), and DSC analysis indicated that none of the microgels exhibited a denaturing or unfolding transition below 54°C regardless of the iron: hemoglobin ratio. Initial testing has been performed on the ability of these materials to act as magnetically activated drug delivery vehicles. Other pertinent tests (for magnetic properties and MRI applicability) are currently proceeding at external labs.

Synthesis and characterization of new ionic liquids

International Nuclear Information System (INIS)

Oliveira, L.M.C. de; Mattedi, S.; Boaventura, J.S.; Iglesias, M.; Universidad de Santiago de Compostela

2010-01-01

In recent years, ionic liquids have been highlighted for its potential in various industrial applications. Among them, the salts of Broensted has a promising profile for the low toxicity, low cost and simple synthesis. This paper presents the synthesis and characterization of new salts of Bronsted with branched (lactate) or large chain anions (oleate) for future use as additives promoters of proton conductivity in fuel cells of ethanol. Experimental data were measured for density, sound velocity and conductivity of pure ionic liquids and mixtures. The density decreases linearly with increasing temperature, and sound velocity shows a similar trend, but not linear. The conductivity increases according to the Arrhenius model with activation energy less than 10 J/mol. Tests NMR, FTIR and TGA confirm ionic structure and thermal stability up to 165 deg C. (author)

Synthesis and characterization of Taurine

Directory of Open Access Journals (Sweden)

B Bayarmaa

2014-10-01

Full Text Available Have been obtained 2-aminoethanesulfonic acid (taurine from ethanolamine, sulfuric acid and sodium sulfite during the synthesis in laboratory condition. The process involves two steps of reactions, the first was esterification of ethanolamine with sulfuric acid to produce the intermediate product of 2-aminoethyl ester which than was extended to the second step by sulfonation with sodium sulfite to produce 2-aminoethanesulfonic acid. Resulting product was analyzed using 1H-NMR, IR, FAB-MS analysis and examined purity characterizations of the synthesized products. DOI: http://dx.doi.org/10.5564/mjc.v14i0.200 Mongolian Journal of Chemistry 14 (40, 2013, p57-60

Synthesis and characterization of a nanostructured matrix hydroxyapatite ceramic bone reconstruction

International Nuclear Information System (INIS)

Correa, P.; Camargo, N.H.A.; Silva, D.F.

2012-01-01

The nanostructured ceramics have been shown promise as biomaterials for bone reconstruction. Among calcium phosphates, hydroxyapatite Ca/P ratio = 1.67 mol stands out because of its crystallographic similarity with the mineral bone phase and biocompatibility. This work was based on synthesis and characterization of a nanostructured hydroxyapatite for use in reconstituting bone tissue. The synthesis method for obtaining the bioceramic powder occurred at process of dissolution/precipitation, involving CaO solid/liquid and phosphoric acid required for forming the composition of Ca/P = 1.67 mole. The material recovered from the synthesis was calcined at 900 ° C/2h, providing the hydroxyapatite powder nanometer. This was subjected to mechanical fragmentation process in mill attritor, providing a hydroxyapatite with modified surface morphology. The results presented relate to morphological characterization studies (SEM), mineralogical (XRD), chemical (FTIR) and particle size distribution, using the laser particle size analysis method. Such results showed the formation of hydroxyapatite phase and morphology satisfactory for use in reconstituting bone tissue

Lanthanide phosphonates: Synthesis, thermal stability and magnetic characterization

Energy Technology Data Exchange (ETDEWEB)

Amghouz, Z., E-mail: amghouz.uo@uniovi.es [Departamentos de Quimica Fisica y Analitica y Quimica Organica e Inorganica, Universidad de Oviedo - CINN, 33006 Oviedo (Spain); Garcia, J.R.; Garcia-Granda, S. [Departamentos de Quimica Fisica y Analitica y Quimica Organica e Inorganica, Universidad de Oviedo - CINN, 33006 Oviedo (Spain); Clearfield, A. [Department of Chemistry, Texas A and M University, College Station, TX 77842-3012 (United States); Rodriguez Fernandez, J.; Pedro, I. de [CITIMAC, Facultad de Ciencias, Universidad de Cantabria, 39005 Santander (Spain); Blanco, J.A. [Departamento de Fisica, Universidad de Oviedo, 33007 Oviedo (Spain)

2012-09-25

Highlights: Black-Right-Pointing-Pointer Report of the complete series of lanthanide 1,4-phenylbis(phosphonate). Black-Right-Pointing-Pointer Synthesis under conventional hydrothermal synthesis or microwave-assisted hydrothermal synthesis. Black-Right-Pointing-Pointer Cation size is the key factor for the structural and particles size variations. Black-Right-Pointing-Pointer Thermal behaviour is characterized by unusual very high thermal stability. - Abstract: Series of novel organic-inorganic hybrids materials based on trivalent lanthanides (Ln = Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) and 1,4-phenylbis(phosphonate) obtained under hydrothermal conditions either by oven heat or microwave irradiation. The anhydrous compounds containing La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, and Ho, are isostructural. However, the compounds based on Y, Er, Tm, Yb, and Lu are hydrated and their structures have not yet been solved. The series of compounds are characterized by PXRD, TEM, SEM-EDX and thermal analyses (TG-MS and DSC). TEM study show a variable particles size with a minimum mean-particle size of ca. 30 nm. These compounds exhibit unusual very high thermal stability. The size of particles and the thermal stability are depending on lanthanide(III) cation features. All the investigated materials show paramagnetic behaviour. The magnetic susceptibility data follow a Curie-Weiss laws with paramagnetic effective moments in good agreement with those expected for Ln{sup 3+} free ions.

Synthesis, Properties Characterization and Applications of Various Organobismuth Compounds

Directory of Open Access Journals (Sweden)

Jingfei Luan

2011-05-01

Full Text Available Organobismuth chemistry was emphasized in this review article due to the low price, low toxicity and low radioactivity characteristics of bismuth. As an environmentally-friendly class of organometallic compounds, different types of organobismuth compounds have been used in organic synthesis, catalysis, materials, etc. The synthesis and property characterization of many organobismuth compounds had been summarized. This review article also presented a survey of various applications of organobismuth compounds in organic transformations, as reagents or catalysts. The reactivity, reaction pathways and mechanisms of reactions with organobismuths were discussed. Less common and limiting aspects of organobismuth compounds were also briefly mentioned.

SYNTHESIS AND CHARACTERIZATION OF NEW HALOGENATED CURCUMINOIDS

Directory of Open Access Journals (Sweden)

Eugenio Torres

2013-12-01

Full Text Available In this work a novel procedure of synthesis of compounds analogues to curcumin with halogens atoms in its structure is described, which can increase its solubility and biological activity. Four halogenated curcuminoids were obtained with great pharmacological interest, none of them reported in literature before. Synthesis was carried out by means of the aldol condensation assisted by microwaves of halogenated aromatic aldehydes and acetylacetona, using morpholine as basic catalyst, in absence of solvent, and the reaction just needed 1 min. The products were purified by treatment of the reaction mixture with methanol under ultrasound irradiation, followed by chromatographic column. All obtained compounds were characterized by infrared spectroscopy, nuclear magnetic resonance, quantitative elementary analysis and high resolution mass spectrometry. The RMN-1H data demonstrate in all structures of synthesized curcuminoids the enol form is the most favored.

Synthesis and characterization of thermally oxidized ZnO films

Indian Academy of Sciences (India)

Administrator

Synthesis and characterization of thermally oxidized ZnO films. A P RAMBU1,* and N IFTIMIE2 .... R. −. Δ. = = (1) where Ra is the sensor resistance in the air and Rg is the .... ple, Aida and coworkers (2006) reported that the total oxidation is ...

Synthesis, characterization and physiological activity of some novel isoxazoles.

Directory of Open Access Journals (Sweden)

NITIN G. GHODILE

2012-07-01

Full Text Available Hushare VJ, Rajput PR, Malpani MO, Ghodile NG. 2012. Synthesis, characterization and physiological activity of some novel isoxazoles. Nusantara Bioscience 4: 81-85. A series of chlorosubstituted 4-aroylisoxazoles have been synthesized by refluxing chlorosubstituted-3-aroylflavones and 3-alkoylchromone with hydroxylamine hydrochloride in dioxane medium containing 0.5 mL piperidine. Chlorosubstituted-3-aroylflavones and chlorosubstituted-3-alkoylchromone were prepared by refluxing them separately with iodine crystal in ethanol. Initially chlorosubstituted-3-aroylflavanones and 3-alkoylchromanone were prepared by the interaction of different aromatic and aliphatic aldehydes with 1-(2’-hydroxy-3’,5’-dichlorophenyl-3-phenyl-1,3-propanedione. Constitutions of synthesized compounds were confirmed on the basis of elemental analysis, molecular weight determination, UV-Visible, I.R. and 1H-NMR spectral data. The titled compounds were evaluated for their growth promoting activity on some flowering plants viz. Papaver rhoeas, Calendula officinalise, Gladiola tristis, Gaillardia aristata, Dianthus chinensis, and Iberis sp. (candytuft. The results indicate that applicated plants had higher shoots and more number of leaves.

Phylogenomically guided identification of industrially relevant GH1 β-glucosidases through DNA synthesis and nanostructure-initiator mass spectrometry.

Science.gov (United States)

Heins, Richard A; Cheng, Xiaoliang; Nath, Sangeeta; Deng, Kai; Bowen, Benjamin P; Chivian, Dylan C; Datta, Supratim; Friedland, Gregory D; D'Haeseleer, Patrik; Wu, Dongying; Tran-Gyamfi, Mary; Scullin, Chessa S; Singh, Seema; Shi, Weibing; Hamilton, Matthew G; Bendall, Matthew L; Sczyrba, Alexander; Thompson, John; Feldman, Taya; Guenther, Joel M; Gladden, John M; Cheng, Jan-Fang; Adams, Paul D; Rubin, Edward M; Simmons, Blake A; Sale, Kenneth L; Northen, Trent R; Deutsch, Samuel

2014-09-19

Harnessing the biotechnological potential of the large number of proteins available in sequence databases requires scalable methods for functional characterization. Here we propose a workflow to address this challenge by combining phylogenomic guided DNA synthesis with high-throughput mass spectrometry and apply it to the systematic characterization of GH1 β-glucosidases, a family of enzymes necessary for biomass hydrolysis, an important step in the conversion of lignocellulosic feedstocks to fuels and chemicals. We synthesized and expressed 175 GH1s, selected from over 2000 candidate sequences to cover maximum sequence diversity. These enzymes were functionally characterized over a range of temperatures and pHs using nanostructure-initiator mass spectrometry (NIMS), generating over 10,000 data points. When combined with HPLC-based sugar profiling, we observed GH1 enzymes active over a broad temperature range and toward many different β-linked disaccharides. For some GH1s we also observed activity toward laminarin, a more complex oligosaccharide present as a major component of macroalgae. An area of particular interest was the identification of GH1 enzymes compatible with the ionic liquid 1-ethyl-3-methylimidazolium acetate ([C2mim][OAc]), a next-generation biomass pretreatment technology. We thus searched for GH1 enzymes active at 70 °C and 20% (v/v) [C2mim][OAc] over the course of a 24-h saccharification reaction. Using our unbiased approach, we identified multiple enzymes of different phylogentic origin with such activities. Our approach of characterizing sequence diversity through targeted gene synthesis coupled to high-throughput screening technologies is a broadly applicable paradigm for a wide range of biological problems.

Encapsulated Nanoparticle Synthesis and Characterization for Improved Storage Fluids: Preprint

Energy Technology Data Exchange (ETDEWEB)

Glatzmaier, G. C.; Pradhan, S.; Kang, J.; Curtis, C.; Blake, D.

2010-10-01

Nanoparticles are typically composed of 50--500 atoms and exhibit properties that are significantly different from the properties of larger, macroscale particles that have the same composition. The addition of these particles to traditional fluids may improve the fluids' thermophysical properties. As an example, the addition of a nanoparticle or set of nanoparticles to a storage fluid may double its heat capacity. This increase in heat capacity would allow a sensible thermal energy storage system to store the same amount of thermal energy in half the amount of storage fluid. The benefit is lower costs for the storage fluid and the storage tanks, resulting in lower-cost electricity. The goal of this long-term research is to create a new class of fluids that enable concentrating solar power plants to operate with greater efficiency and lower electricity costs. Initial research on this topic developed molecular dynamic models that predicted the energy states and transition temperatures for these particles. Recent research has extended the modeling work, along with initiating the synthesis and characterization of bare metal nanoparticles and metal nanoparticles that are encapsulated with inert silica coatings. These particles possess properties that make them excellent candidates for enhancing the heat capacity of storage fluids.

Synthesis and characterization of amorphous cellulose from triacetate of cellulose

International Nuclear Information System (INIS)

Vega-Baudrit, Jose; Sibaja, Maria; Nikolaeva, Svetlana; Rivera A, Andrea

2014-01-01

It was carried-out a study for the synthesis and characterization of amorphous cellulose starting from cellulose triacetate. X-rays diffraction was used in order to obtain the cellulose crystallinity degree, also infrared spectroscopy FTIR was used. (author)

Characterization structural and morphology ZSM-5 zeolite by hydrothermal synthesis

International Nuclear Information System (INIS)

Silva, V.J.; Crispim, A.C.; Queiroz, M.B.; Laborde, H.M.; Rodrigues, M.G.F.; Menezes, R.R.

2009-01-01

Solid acids are catalytic materials commonly used in the chemical industry. Among these zeolites are the most important business processes including water treatment, gas separation, and cracking long hydrocarbon chains to produce high octane gasoline. Its synthesis, characterization and applications have been widely studied. The objective this study was to synthesize the ZSM-5 zeolite for future use in separation processes and catalysis. The zeolite ZSM-5 was prepared by hydrothermal synthesis at 170°C, using silica, deionized water and the director of structures (TPABr - tetrapropylammonium bromide). The materials were characterized by X ray diffraction (XRD), scanning electron microscopy (SEM) and semiquantitative chemical analysis by X ray fluorescence (XRF). According to the XRD was possible to observe the formation of ZSM-5 zeolite, with peaks intense and well defined. The SEM showed the formation of individual particles, clean, rounded shapes. (author)

Synthesis and characterization of five-coordinated indium amidinates

Energy Technology Data Exchange (ETDEWEB)

Riahi, Yasaman

2016-07-29

The focus of this work is synthesis, characterization and exploring the reactivity of new indium amidinate compounds of the type R{sub 2}InX (R = R''NCR'NR''; R' = Ph, R'' = SiMe{sub 3}, iPr, dipp; X = Br, Cl) with the coordination number of five and R{sub 3}In (R = Me{sub 3}SiNCPhNSiMe{sub 3}) with the coordination number of six. By using amidinates as chelating ligands the electron deficiency of indium atom will be resolved. Additionally, by using different substituents the study of the different synthesized indium amidinates has become possible. The selected method for the synthesis allows the carbodiimides to react with organolithium compounds to get the corresponding lithium amidinates. Afterwards the resulting lithium amidinates take part in transmetalation reactions with InBr{sub 3} and InCl{sub 3}. The study of the reactivity of indium amidinate complexes including nucleophilic reactions as well as their reduction were also examined. Beside crystal structure analysis, nuclear magnetic resonance spectroscopy as well as elemental analysis has been applied to characterize the compounds.

Identification and Functional Characterization of the Glycogen Synthesis Related Gene Glycogenin in Pacific Oysters (Crassostrea gigas).

Science.gov (United States)

Li, Busu; Meng, Jie; Li, Li; Liu, Sheng; Wang, Ting; Zhang, Guofan

2017-09-06

High glycogen levels in the Pacific oyster (Crassostrea gigas) contribute to its flavor, quality, and hardiness. Glycogenin (CgGN) is the priming glucosyltransferase that initiates glycogen biosynthesis. We characterized the full sequence and function of C. gigas CgGN. Three CgGN isoforms (CgGN-α, β, and γ) containing alternative exon regions were isolated. CgGN expression varied seasonally in the adductor muscle and gonadal area and was the highest in the adductor muscle. Autoglycosylation of CgGN can interact with glycogen synthase (CgGS) to complete glycogen synthesis. Subcellular localization analysis showed that CgGN isoforms and CgGS were located in the cytoplasm. Additionally, a site-directed mutagenesis experiment revealed that the Tyr200Phe and Tyr202Phe mutations could affect CgGN autoglycosylation. This is the first study of glycogenin function in marine bivalves. These findings will improve our understanding of glycogen synthesis and accumulation mechanisms in mollusks. The data are potentially useful for breeding high-glycogen oysters.

Synthesis and Characterization of Novel Quaternary Thioaluminogermanates

KAUST Repository

Al-Bloushi, Mohammed

2013-05-01

Metal chalcogenides form an important class of inorganic materials, which include several technologically important applications. The design of metal chlcogenides is of technological interest and has encouraged recent research into moderate temperature solid-state synthetic methods for the single crystal growth of new materials. The aim of this project is the investigation and development of synthetic methodology for the synthesis of novel metal chlcogenides. The new inorganic compounds of the type “M(AlS2)(GeS2)” (M = Na and K) are new metal-chalcogenides, synthesized by the classical solid state approach. The characterization of these compounds was carried out by Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDS), Single crystal and powder X-ray diffraction, solid state Nuclear Magnetic Resonance (NMR), Ultraviolet-visible (UV-VIS), Infrared (IR) and Raman spectroscopy. These theses study the synthesis of metal chalcogenides through the use of standard chemical techniques. The systematic studies demonstrate the effect of the reactants ratio and reaction temperature on the synthesis and growth of the single crystals. Metal chalcogenides have several potential applications in gas separation, ion exchange, environmental remediation, and energy storage. Especially, the ion exchange materials have found\\tpossible applications in waste-water treatment, water softening, metal separation, and production of high purity water.

Fabrication of luminescent hydroxyapatite nanorods through surface-initiated RAFT polymerization: Characterization, biological imaging and drug delivery applications

Energy Technology Data Exchange (ETDEWEB)

Heng, Chunning [Shaanxi Key Laboratory of Degradable Biomedical Materials, Shaanxi R& D Center of Biomaterials and Fermentation Engineering, School of Chemical and Engineering, Northwest University, Xi’an, 710069 (China); Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Zheng, Xiaoyan [Shaanxi Key Laboratory of Degradable Biomedical Materials, Shaanxi R& D Center of Biomaterials and Fermentation Engineering, School of Chemical and Engineering, Northwest University, Xi’an, 710069 (China); Liu, Meiying; Xu, Dazhuang; Huang, Hongye; Deng, Fengjie [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Hui, Junfeng, E-mail: huijunfeng@126.com [Shaanxi Key Laboratory of Degradable Biomedical Materials, Shaanxi R& D Center of Biomaterials and Fermentation Engineering, School of Chemical and Engineering, Northwest University, Xi’an, 710069 (China); Zhang, Xiaoyong, E-mail: xiaoyongzhang1980@gmail.com [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Wei, Yen, E-mail: weiyen@tsinghua.edu.cn [Department of Chemistry and the Tsinghua Center for Frontier Polymer Research, Tsinghua University, Beijing, 100084 (China)

2016-11-15

Highlights: • Hydrophobic hydroxyapatite nanorods were obtained from hydrothermal synthesis. • Surface initiated RAFT polymerization was adopted to surface modification of hydroxyapatite nanorods. • These modified hydroxyapatite nanorods showed high water dispersibility and biocompatibility. • These modified hydroxyapatite nanorods can be used for controlled drug delivery. - Abstract: Hydroxyapatite nanomaterials as an important class of nanomaterials, have been widely applied for different biomedical applications for their excellent biocompatibility, biodegradation potential and low cost. In this work, hydroxyapatite nanorods with uniform size and morphology were prepared through hydrothermal synthesis. The surfaces of these hydroxyapatite nanorods are covered with hydrophobic oleic acid, making them poor dispersibility in aqueous solution and difficult for biomedical applications. To overcome this issue, a simple surface initiated polymerization strategy has been developed via combination of the surface ligand exchange and reversible addition fragmentation chain transfer (RAFT) polymerization. Hydroxyapatite nanorods were first modified with Riboflavin-5-phosphate sodium (RPSSD) via ligand exchange reaction between the phosphate group of RPSSD and oleic acid. Then hydroxyl group of nHAp-RPSSD was used to immobilize chain transfer agent, which was used as the initiator for surface-initiated RAFT polymerization. The nHAp-RPSSD-poly(IA-PEGMA) nanocomposites were characterized by means of {sup 1}H nuclear magnetic resonance, Fourier transform infrared spectroscopy, fluorescence spectroscopy and thermal gravimetric analysis in detailed. The biocompatibility, biological imaging and drug delivery of nHAp-RPSSD-poly(IA-PEGMA) were also investigated. Results showed that nHAp-RPSSD-poly(IA-PEGMA) exhibited excellent water dispersibility, desirable optical properties, good biocompatibility and high drug loading capability, making them promising candidates for

Fabrication of luminescent hydroxyapatite nanorods through surface-initiated RAFT polymerization: Characterization, biological imaging and drug delivery applications

International Nuclear Information System (INIS)

Heng, Chunning; Zheng, Xiaoyan; Liu, Meiying; Xu, Dazhuang; Huang, Hongye; Deng, Fengjie; Hui, Junfeng; Zhang, Xiaoyong; Wei, Yen

2016-01-01

Highlights: • Hydrophobic hydroxyapatite nanorods were obtained from hydrothermal synthesis. • Surface initiated RAFT polymerization was adopted to surface modification of hydroxyapatite nanorods. • These modified hydroxyapatite nanorods showed high water dispersibility and biocompatibility. • These modified hydroxyapatite nanorods can be used for controlled drug delivery. - Abstract: Hydroxyapatite nanomaterials as an important class of nanomaterials, have been widely applied for different biomedical applications for their excellent biocompatibility, biodegradation potential and low cost. In this work, hydroxyapatite nanorods with uniform size and morphology were prepared through hydrothermal synthesis. The surfaces of these hydroxyapatite nanorods are covered with hydrophobic oleic acid, making them poor dispersibility in aqueous solution and difficult for biomedical applications. To overcome this issue, a simple surface initiated polymerization strategy has been developed via combination of the surface ligand exchange and reversible addition fragmentation chain transfer (RAFT) polymerization. Hydroxyapatite nanorods were first modified with Riboflavin-5-phosphate sodium (RPSSD) via ligand exchange reaction between the phosphate group of RPSSD and oleic acid. Then hydroxyl group of nHAp-RPSSD was used to immobilize chain transfer agent, which was used as the initiator for surface-initiated RAFT polymerization. The nHAp-RPSSD-poly(IA-PEGMA) nanocomposites were characterized by means of "1H nuclear magnetic resonance, Fourier transform infrared spectroscopy, fluorescence spectroscopy and thermal gravimetric analysis in detailed. The biocompatibility, biological imaging and drug delivery of nHAp-RPSSD-poly(IA-PEGMA) were also investigated. Results showed that nHAp-RPSSD-poly(IA-PEGMA) exhibited excellent water dispersibility, desirable optical properties, good biocompatibility and high drug loading capability, making them promising candidates for biological

A Comparative Characterization of the HPA-MCM-48 Type Catalysts Produced by the Direct Hydrothermal and Room Temperature Synthesis Methods

International Nuclear Information System (INIS)

Gucbilmez, Y.; Calis, I.; Yargic, A. S.

2012-01-01

MCM-48 type support materials synthesized by the direct hydrothermal synthesis (HTS) and room temperature synthesis (RTS) methods were incorporated with tungstophosphoric acid (TPA) in the range of 10-40 wt% by using a wet impregnation technique in methanol solutions. Resulting HPA-MCM-48 catalysts were characterized by the XRD, Nitrogen Physisorption, SEM, TEM, EDS, and FT-IR methods in order to determine the effects of different initial synthesis conditions on the catalyst properties. RTS samples were found to have better crystalline structures, higher BET surface areas, and higher BJH pore volumes than HTS samples. They also had slightly higher TPA incorporation, except for the 40 wt% samples, as evidenced by the EDS results. Keggin ion structure was preserved, for both methods, even at the highest acid loading of 40 wt%. It was concluded that the simpler and more economical RTS method was more successful than the HTS method for hetero poly acid incorporation into MCM-48 type materials

Synthesis and characterization of innovative insulation materials

Directory of Open Access Journals (Sweden)

Skaropoulou Aggeliki

2018-01-01

Full Text Available Insulation elements are distinguished in inorganic fibrous and organic foamed materials. Foamed insulation materials are of great acceptance and use, but their major disadvantage is their flammability. In case of fire, they tend to transmit the flame producing toxic gases. In this paper, the synthesis and characterization of innovative inorganic insulation materials with properties competitive to commercial is presented. Their synthesis involves the mixing of inorganic raw material and water with reinforcing agent or/and foaming agent leading to the formation of a gel. Depending on raw materials nature, the insulation material is produced by freeze drying or ambient drying techniques of the gel. The raw material used are chemically benign and abundantly available materials, or industrial by-products and the final products are non-toxic and, in some cases, non-flammable. Their density and thermal conductivity was measured and found 0.02-0.06 g/cm3 and 0.03-0.04 W/mK, respectively.

Synthesis and Characterization of Two New p-tert-Butylcalix[4]-arene Schiff Bases

Directory of Open Access Journals (Sweden)

Saeed Taghvaee Ganjali

2001-03-01

Full Text Available Synthesis and characterization of two new Schiff bases of p-tertbuthylcalix[4]arene (H2L1 and HL2 is described. The synthesis of H2L1 and HL2 has been achieved by the condensation of salicylaldehyde with the amine group of upper rim monoamine p-tert-butylcalix[4]arene in ethanol. These compounds have been characterized on the basis of elemental analysis and spectral data. Solvatochromicity and fluorescence properties were observed and measured for H2L1 and HL2. Solvatochromicity of these ligands indicates their potential for NLO applications.

Graphene optoelectronics synthesis, characterization, properties, and applications

CERN Document Server

bin M Yusoff, Abdul Rashid

2014-01-01

This first book on emerging applications for this innovative material gives an up-to-date account of the many opportunities graphene offers high-end optoelectronics.The text focuses on potential as well as already realized applications, discussing metallic and passive components, such as transparent conductors and smart windows, as well as high-frequency devices, spintronics, photonics, and terahertz devices. Also included are sections on the fundamental properties, synthesis, and characterization of graphene. With its unique coverage, this book will be welcomed by materials scientists, solid-

Synthesis and characterization of triangulene

Science.gov (United States)

Pavliček, Niko; Mistry, Anish; Majzik, Zsolt; Moll, Nikolaj; Meyer, Gerhard; Fox, David J.; Gross, Leo

2017-05-01

Triangulene, the smallest triplet-ground-state polybenzenoid (also known as Clar's hydrocarbon), has been an enigmatic molecule ever since its existence was first hypothesized. Despite containing an even number of carbons (22, in six fused benzene rings), it is not possible to draw Kekulé-style resonant structures for the whole molecule: any attempt results in two unpaired valence electrons. Synthesis and characterization of unsubstituted triangulene has not been achieved because of its extreme reactivity, although the addition of substituents has allowed the stabilization and synthesis of the triangulene core and verification of the triplet ground state via electron paramagnetic resonance measurements. Here we show the on-surface generation of unsubstituted triangulene that consists of six fused benzene rings. The tip of a combined scanning tunnelling and atomic force microscope (STM/AFM) was used to dehydrogenate precursor molecules. STM measurements in combination with density functional theory (DFT) calculations confirmed that triangulene keeps its free-molecule properties on the surface, whereas AFM measurements resolved its planar, threefold symmetric molecular structure. The unique topology of such non-Kekulé hydrocarbons results in open-shell π-conjugated graphene fragments that give rise to high-spin ground states, potentially useful in organic spintronic devices. Our generation method renders manifold experiments possible to investigate triangulene and related open-shell fragments at the single-molecule level.

Synthesis and characterization of sulfur-functionalized silica nanocapsules as mercury adsorbents

Science.gov (United States)

Palaniappan, Thenappan; Saman, Norasikin; Mat, Hanapi; Johari, Khairiraihanna

2017-12-01

Sulfur functionalized silica nanocapsules (S-SiNC) was successfully synthesized and characterized as a potential adsorbent for industrial applications. The synthesis of S-SiNC was carried out using the mircoemulsion templating method using cetyltrimethylammonium bromide (CTAB) as cationic surfactant, toluene as co-solvent, ammonia solution as catalyst, and tetraethylorthosilicate (TEOS) as the silica base. The S-SiNC adsorbent was characterized using Transmission Electron Microscope, Fourier Transformed Infra Red spectroscopy and nitrogen adsorption/desorption analysis. The physical and chemical properties of the SiNC changed as a result of the functionalization, hence affecting the extent of Hg(II) adsorption. The S-SiNCs were also tested in mercury ion [Hg(II)] adsorption via batch adsorption process with variation in initial Hg (II) concentration. It was found that there is a significant improvement in Hg(II) adsorption performance after being functionalized with elemental sulfur. The highest Hg(II) adsorption capacity was obtained for S-SiNC (107.875 mg/g), which significantly outperformed the blank SiNC. The experimental data obtained was found to be fitting well to the Langmuir isotherm model (R2= 0.979) compared to Freundlich isotherm model. Thus, the results demonstrated the potential application of sulfur functionalized silica nanocapsules as adsorbent in industrial applications.

Microwave hydrothermal synthesis and characterization of PZT 52/48 powders

International Nuclear Information System (INIS)

Teixeira, G.F.; Gasparotto, G.; Santos, N.A.; Zaghete, M.A.; Varela, J.A.; Longo, E.

2009-01-01

Full text: Lead Zirconate Titanate (PZT) is a ceramic witch has great interest because of their ferroelectric, piezoelectric, and other electrical properties. In this work Pb(ZrxTi1-x)O3 powders were synthesized by microwave hydrothermal synthesis (M-H) at 180°C without excess lead content. This method allows obtaining particles whit nanometer size, good stoichiometric controls, high purity and crystalline degree at low temperatures and short times of synthesis. Powders were synthesized with molar concentration of 0.15 mol.L -1 during different times: 30 min, 2, 4, 6 and 8 h. After that the powders were characterized by X-ray diffraction (XRD), Field Emission Gun (FEG) and photoluminescence (PL). Through analysis it is observed that the crystalline phase of PZT is obtained from 2 hours of synthesis and this same time also presents more intense PL emission. (author)

Electronic, electrical and magnetic ceramics synthesis and characterization

International Nuclear Information System (INIS)

Calix, V.S.; Saligan, P.P.; Naval, P.C.

1989-01-01

This paper describes the research and development activities of the Philippine Nuclear Research Institute (PNRI) on the synthesis and characterization of soft and hard ferrites and some beta alumina type superionic conductor materials. XRD, XRF and Moessbauer effect spectrometry are used to determine the structure phases, compositions and some magnetic properties of the materials. Effects of composition and preparation methods on the bulk electronic and magnetic properties are also discussed. (Auth.). 6 figs.; 3 tabs

Materials-by-design: computation, synthesis, and characterization from atoms to structures

Science.gov (United States)

Yeo, Jingjie; Jung, Gang Seob; Martín-Martínez, Francisco J.; Ling, Shengjie; Gu, Grace X.; Qin, Zhao; Buehler, Markus J.

2018-05-01

In the 50 years that succeeded Richard Feynman’s exposition of the idea that there is ‘plenty of room at the bottom’ for manipulating individual atoms for the synthesis and manufacturing processing of materials, the materials-by-design paradigm is being developed gradually through synergistic integration of experimental material synthesis and characterization with predictive computational modeling and optimization. This paper reviews how this paradigm creates the possibility to develop materials according to specific, rational designs from the molecular to the macroscopic scale. We discuss promising techniques in experimental small-scale material synthesis and large-scale fabrication methods to manipulate atomistic or macroscale structures, which can be designed by computational modeling. These include recombinant protein technology to produce peptides and proteins with tailored sequences encoded by recombinant DNA, self-assembly processes induced by conformational transition of proteins, additive manufacturing for designing complex structures, and qualitative and quantitative characterization of materials at different length scales. We describe important material characterization techniques using numerous methods of spectroscopy and microscopy. We detail numerous multi-scale computational modeling techniques that complements these experimental techniques: DFT at the atomistic scale; fully atomistic and coarse-grain molecular dynamics at the molecular to mesoscale; continuum modeling at the macroscale. Additionally, we present case studies that utilize experimental and computational approaches in an integrated manner to broaden our understanding of the properties of two-dimensional materials and materials based on silk and silk-elastin-like proteins.

Synthesis and characterization of composites of mixed oxides of iron ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 34; Issue 4. Synthesis and characterization of composites of mixed oxides of iron and neodymium in polymer matrix of aniline–formaldehyde. Sajdha H N Sheikh B L Kalsotra N Kumar S Kumar. Volume 34 Issue 4 July 2011 pp 843-851 ...

Chondroitin sulfate proteoglycan synthesis and reutilization of beta-D-xyloside-initiated chondroitin/dermatan sulfate glycosaminoglycans in fetal kidney branching morphogenesis

International Nuclear Information System (INIS)

Klein, D.J.; Brown, D.M.; Moran, A.; Oegema, T.R. Jr.; Platt, J.L.

1989-01-01

Branching morphogenesis and chondroitin sulfate proteoglycan synthesis by explanted fetal mouse kidneys were previously shown to be inhibited by p-nitrophenyl beta-D-xylopyranoside (beta-D-xyloside) while glomerular development and heparan sulfate proteoglycan synthesis were unaffected. The metabolic fate of fetal kidney explant proteoglycans was investigated to determine whether or not recovery of proteoglycan synthesis and morphogenesis occur after exposure to beta-D-xyloside. Chondroitin sulfate proteoglycan synthesis resumed within 4 hr of removal of beta-D-xyloside and was enhanced once beta-D-xyloside-initiated chondroitin/dermatan- 35 SO 4 glycosaminoglycans (GAGs) were released from the tissue. Radioactivity incorporated into beta-D-xyloside-initiated chondroitin/dermatan- 35 SO 4 GAGs during labeling in the presence of beta-D-xyloside was reutilized in the synthesis of chondroitin- 35 SO 4 proteoglycan during a 24-hr chase in nonradioactive medium without beta-D-xyloside. Further, highly purified beta-D-xyloside-initiated chondroitin/dermatan- 35 SO 4 GAGs were taken up by kidneys more avidly than was free [ 35 S]sulfate. These 35 S-GAGs were degraded and reutilized in the synthesis of chondroitin- 35 SO 4 proteoglycan. Ureteric bud branching resumed 48 hr after beta-D-xyloside was removed from the incubation medium. These findings support the idea that both chondroitin sulfate proteoglycan synthesis and proteoglycan processing may be involved in branching morphogenesis

Synthesis of poly(D,L-lactide-co-glycolide) copolymers and its chemical characterization by NMR and FTIR

International Nuclear Information System (INIS)

Erbetta, Cynthia D.C.; Viegas, Carla C.B.; Freitas, Roberto F.S.; Sousa, Ricardo G.

2011-01-01

Poly(D,L-lactide-co-glycolide) copolymer is of great interest for medical applications. This interest is justified by the fact that it is bioreabsorbable, biocompatible and non-toxic, while its degradation kinetics can be modified by the copolymerization ratio of the monomers. In this study, copolymers were synthesized at 175 deg C by opening the rings of the cyclic dimers of the D,L-lactide and glycolide monomers in the presence of stannous octoate initiator and lauryl alcohol co-initiator. The efficient application of a vacuum to the reaction medium, coupled with adequate stirring, is fundamental for the success of the synthesis. The following analysis techniques were used to characterize the synthesized copolymers: Nuclear Magnetic Resonance Spectroscopy (NMR) and Fourier Transform Infrared Spectroscopy (FTIR). The chemical composition and the ratio of the monomers in the synthesized copolymer were determined. (author)

The Synthesis, Characterization and Catalytic Reaction Studies of Monodisperse Platinum Nanoparticles in Mesoporous Oxide Materials

Energy Technology Data Exchange (ETDEWEB)

Rioux, Robert M. [Univ. of California, Berkeley, CA (United States)

2006-01-01

A catalyst design program was implemented in which Pt nanoparticles, either of monodisperse size and/or shape were synthesized, characterized and studied in a number of hydrocarbon conversion reactions. The novel preparation of these materials enables exquisite control over their physical and chemical properties that could be controlled (and therefore rationally tuned) during synthesis. The ability to synthesize rather than prepare catalysts followed by thorough characterization enable accurate structure-function relationships to be elucidated. This thesis emphasizes all three aspects of catalyst design: synthesis, characterization and reactivity studies. The precise control of metal nanoparticle size, surface structure and composition may enable the development of highly active and selective heterogeneous catalysts.

Synthesis of [3H] Zolpidem

International Nuclear Information System (INIS)

Allen, J.; Parent, G.; Tizot, A.

1986-01-01

Zolpidem is a novel hypnotic agent possessing a substituted imidazo [1,2-a] pyridine structure. The synthesis of the tritium labelled compound with a specific activity of 60.5 Ci/mmol is described. This new radioligand was initially used to establish and characterize the binding properties of Zolpidem in the rat brain. (author)

Synthesis and characterization of energetic thermoplastic elastomers for propellant formulations

Directory of Open Access Journals (Sweden)

Aparecida M. Kawamoto

2009-01-01

Full Text Available Synthesis and characterization of energetic ABA-type thermoplastic elastomers for propellant formulations has been carried out. Following the working plan elaborated, the synthesis and characterization of Poly 3- bromomethyl-3-methyl oxetane (PolyBrMMO, Poly 3- azidomethyl-3-methyl oxetane (PolyAMMO, Poly 3,3-bis-azidomethyl oxetane (PolyBAMO and Copolymer PolyBAMO/AMMO (by TDI end capping has been successfully performed. The thermoplastic elastomers (TPEs were synthesized using the chain elongation process PolyAMMO, GAP and PolyBAMO by diisocyanates. In this method 2.4-toluene diisocyanate (TDI is used to link block A (hard and mono- functional to B (soft and di-functional. For the hard A-block we used PolyBAMO and for the soft B-block we used PolyAMMO or GAP.This is a joint project set up, some years ago, between the Chemistry Division of the Institute of Aeronautics and Space (IAE - subordinated to the Brazilian Ministry of Defense - and the Fraunhofer Institut Chemische Technologie (ICT, in Germany. The products were characterized by different techniques as IR- and (1H,13CNMR spectroscopies, elemental and thermal analyses. New methodologies based on FT-IR analysis have been developed as an alternative for the determination of the molecular weight and CHNO content of the energetic polymers.

Synthesis and characterization of the silver methacrylate and its polymerization with gamma radiation

International Nuclear Information System (INIS)

Figueroa de Paz, Y. M.

2014-01-01

One of the traditional objectives in research has been the development of new and useful materials that combine the properties of polymers with metals. Synthesis of monomers containing metal, followed by a polymerization process, is a method to introduce metal ions in the structure of a polymer, and the gamma radiation was easily applied to initiate polymerization. The coordination polymers have high insolubility, which is a general problem of these materials, besides the lack of structural information available. Also, due to the difficulty of obtaining single crystals, it has hindered the identification of the structures of some coordination polymers, requiring the use of indirect methods for structural characterization. In this work the synthesis of silver poly-methacrylate (PMAAg), was performed using the gamma radiation as polymerization initiator, having as precursor to silver methacrylate monomer (MAAg). The combination of spectroscopic methods revealed structural changes in the coordination polymers. With scanning electron microscopy, it was observed that the morphology of the monomer and its polymers is fiber, which grows with increasing radiation dose; furthermore, this increase in size is related to Bet analysis result, since the monomer has a bigger superficial area to the irradiated polymers. In monomer and irradiated polymers the crystalline structure CCC was observed by X-ray diffraction. By thermogravimetric analysis the decomposition temperature of the products was determined, finding around 150 degrees C. The infrared spectroscopy confirmed the silver methacrylate polymerization, as with increasing radiation dose, also increases the degree of polymerization; likewise the form of coordination of the monomer was determined and its irradiated polymers which corresponds to a bi-dentate chelate, confirmed by X-ray photoelectron spectroscopy. (Author)

Synthesis and Characterization of Poly(Amidoamine Dendrimers Encapsulatd 198Au Nanoparticles

Directory of Open Access Journals (Sweden)

R. Ritawidya1,2

2012-12-01

Full Text Available Brachytherapy or internal radiotherapy is one of many methods used for treatment of cancer. This modality requires an agent with radionuclides that emits  or β particle with a proper energy. 198Au (99% β max = 0.96 MeV and t1/2 = 2.69 days is one of radionuclides that has been considered to be effective for the above-mentioned purpose. The purpose of this research was to synthesis and characterize poly(amidoamine (PAMAM G3.0 dendrimers encapsulated 198Au nanoparticles as a new brachytherapy agent. PAMAM G3.0 dendrimers encapsulated 198Au nanoparticles was successfully synthesized by a bottom-up method using sodium borohydride as a reductor. Purification was then performed by a size exclusion chromatography in order to separate large Au nanoparticles that were formed outside the cavity of PAMAM G3.0 dendrimers. Prior to the synthesis of PAMAM G3.0 dendrimers encapsulated 198Au nanoparticles, the synthetic procedure was first established by using a non-radioactive Au. The PAMAM G3.0 dendrimers encapsulated Au nanoparticles produced was then characterized by using an UV-Vis spectroscopy, a transmission electron microscopy (TEM, particle size analyzer (PSA, and an atomic absorption spectroscopy (AAS. Characterization results revealed that PAMAM G3.0 dendrimers encapsulated Au nanoparticles that were prepared from a reaction mixture of PAMAM G3.0 dendrimers and Au HAuCl4 with mol ratio of 2.8, was found to be a proper formula. It produced PAMAM G3.0 dendrimers encapsulated Au nanoparticles with diameter of 1.743 nm, spheris, uniform and drug loading value of 26.34%. This formula was then used in synthesis using radioactive Au, 198Au. Characterization results of PAMAM G3.0 dendrimers encapsulated 198Au nanoparticles gave a radiochemical purity of 99.4% and zero charge.

An Investigation of Porous Structure of TiNi-Based SHS-Materials Produced at Different Initial Synthesis Temperatures

Science.gov (United States)

Khodorenko, V. N.; Anikeev, S. G.; Kokorev, O. V.; Yasenchuk, Yu. F.; Gunther, V. É.

2018-02-01

An investigation of structural characteristics and behavior of TiNi-based pore-permeable materials manufactured by the methods of selfpropagating high-temperature synthesis (SHS) at the initial synthesis temperatures T = 400 and 600°C is performed. It is shown that depending on the temperature regime, the resulting structure and properties of the material can differ. It is found out that the SHS-material produced at the initial synthesis temperature T = 400°C possesses the largest number of micropores in the pore wall surface structure due to a high phase inhomogeneity of the alloy. The regime of structure optimization of the resulting materials is described and the main stages of formation of the pore wall microporous surfaces are revealed. It is demonstrated that after optimization of the surface structure of a TiNi-based fine-pore alloy by its chemical etching, the fraction of micropores measuring in size less than 50 nm increased from 59 to 68%, while the number of pores larger than 1 μm increased twofold from 11 to 22%. In addition, peculiar features of interaction between certain cell cultures with the surface of the SHS-material manufactured at different initial synthesis temperatures are revealed. It is found out that the dynamics of the cell material integration depends on the pore wall surface morphology and dimensions of macropores.

Effect of intravenous administration of D-lysergic acid diethylamide on initiation of protein synthesis in a cell-free system derived from brain.

Science.gov (United States)

Cosgrove, J W; Brown, I R

1984-05-01

An initiating cell-free protein synthesis system derived from brain was utilized to demonstrate that the intravenous injection of D-lysergic acid diethylamide (LSD) to rabbits resulted in a lesion at the initiation stage of brain protein synthesis. Three inhibitors of initiation, edeine, poly(I), and aurintricarboxylic acid were used to demonstrate a reduction in initiation-dependent amino acid incorporation in the brain cell-free system. One hour after LSD injection, there was also a measurable decrease in the formation of 40S and 80S initiation complexes in vitro, using either [35S]methionine or [35S]Met-tRNAf. Analysis of the methionine pool size after LSD administration indicated there was no change in methionine levels. Analysis of the formation of initiation complexes in the brain cell-free protein synthesis system prepared 6 h after LSD administration indicated that there was a return to control levels at this time. The effects of LSD on steps in the initiation process are thus reversible.

Synthesis and characterization of dental composites

Science.gov (United States)

Djustiana, Nina; Greviana, Nadia; Faza, Yanwar; Sunarso

2018-02-01

During the last few decades, the increasing demands in esthetic dentistry have led to the development of dental composites material that provide similar appearance to the natural teeth. Recently, esthetic trend was an issue which increase the demand for teeth restorations that is similar with the origin. The esthetics of dental composite are more superior compared to amalgam, since its color look similar with natural teeth. Various dental composites have been developed using many type of fillers such as amorphous silica, quartz), borosilicate, Li-Sr-Ba-Al glass and oxide: zirconia and alumina. Researchers in Faculty of Dentistry University of Padjadjaran have prepared dental composites using zirconia-alumina-silica (ZAS) system as the filler. The aim is to improve the mechanical properties and the esthetic of the dental composites. The ZAS was obtained from chemical grade purity chemicals and Indonesia's natural sand as precursors its characterization were also presented. This novel method covers the procedure to synthesis and characterize dental composites in Padjadjaran University and some review about dental composites in global research.

Timing of initiation of macronuclear DNA synthesis is set during the preceding cell cycle in Paramecium tetraurelia: analysis of the effects of abrupt changes in nutrient level

International Nuclear Information System (INIS)

Ching, A.S.L.; Berger, J.D.

1986-01-01

In many eukaryotic organisms, initiation of DNA synthesis is associated with a major control point within the cell cycle and reflects the commitment of the cell to the DNA replication-division portion of the cell cycle. In paramecium, the timing of DNA synthesis initiation is established prior to fission during the preceding cell cycle. DNA synthesis normally starts at 0.25 in the cell cycle. When dividing cells are subjected to abrupt nutrient shift-up by transfer from a chemostat culture to medium with excess food, or shift-down from a well-fed culture to exhausted medium, DNA synthesis initiation in the post-shift cell cycle occurs at 0.25 of the parental cell cycle and not at either 0.25 in the post-shift cell cycle or at 0.25 in the equilibrium cell cycle produced under the post-shift conditions. The long delay prior to initiation of DNA synthesis following nutritional shift-up is not a consequence of continued slow growth because the rate of protein synthesis increases rapidly to the normal level after shift-up. Analysis of the relation between increase in cell mass and initiation of DNA synthesis following nutritional shifts indicates that increase in cell mass, per se, is neither a necessary nor a sufficient condition for initiation of DNA synthesis, in spite of the strong association between accumulation of cell mass and initiation of DNA synthesis in cells growing under steady-state conditions

Synthesis, characterization and gas sensing performance of SnO2 ...

Indian Academy of Sciences (India)

Synthesis, characterization and gas sensing performance of SnO2 thin films prepared by spray pyrolysis. GANESH E PATIL, D D KAJALE, D N CHAVAN†, N K PAWAR††, P T AHIRE, S D SHINDE#,. V B GAIKWAD# and G H JAIN. ∗. Materials Research Laboratory, Arts, Commerce and Science College, Nandgaon 423 106, ...

Materials Research Society Symposium Proceedings Volume 635. Anisotropic Nanoparticles - Synthesis, Characterization and Applications

National Research Council Canada - National Science Library

Lyon, L

2000-01-01

This volume contains a series of papers originally presented at Symposium C, "Anisotropic Nanoparticles Synthesis, Characterization and Applications," at the 2000 MRS Fall Meeting in Boston, Massachusetts...

Signals for the initiation and termination of synthesis of the viral strand of bacteriophage f1

International Nuclear Information System (INIS)

Dotto, G.P.; Horiuchi, K.; Jakes, K.S.; Zinder, N.D.

1983-01-01

In this paper the sequence around the plus origin that is required for efficient plus-strand synthesis as well as that necessary for gene-II-protein recognition is described. Results which demonstrate that the nucleotide sequence of the f1 plus origin contains two overlapping but distinct signals, one for initiation and the other for termination of plus-strand synthesis is presented. 29 references, 6 figures, 1 table

Nano-/micro metallic wire synthesis on Si substrate and their characterization

International Nuclear Information System (INIS)

Kaur, Jaskiran; Kaur, Harmanmeet; Singh, Surinder; Kanjilal, Dinakar; Chakarvarti, Shiv Kumar

2014-01-01

Nano-/micro wires of copper are grown on semiconducting Si substrate using the template method. It involves the irradiation of 8 um thick polymeric layer coated on Si with150 MeV Ni ion beam at a fluence of 2E8. Later, by using the simple technique of electrodeposition, copper nano-/micro wires were grown via template synthesis. Synthesized wires were morphologically characterized using SEM and electrical characterization was carried out by finding I-V plot

Synthesis and characterization of poly aniline for electrochemical biosensor construction

International Nuclear Information System (INIS)

Magalhaes, Gleice S.L.; Southgate, Erica F.; Alhadeff, Eliana M.; Guimaraes, Maria Jose O.C.

2011-01-01

Conductors polymers have many attractive interests to the industry due their highly technological applications. This work treats specially of polyaniline because it's large electrical conductivity, electrochemical properties, associate to the chemical stability in environmental conditions and synthesis facility. The main of this work is the application in a construction of an electrochemical biosensor for ethanol detection and quantification. Different conditions of synthesis of the conductor emeraldine polyaniline form were studied, investigated the influence of the dopant agent and the reactional environment conditions temperature on the reaction yield and conductivities. The polyaniline that showed the best conductivity were characterized by differential and thermal gravimetric analysis, infrared spectroscopy, X ray diffraction, and cycle voltammetry, comparing with the commercial polyaniline. (author)

Synthesis and characterization of Au incorporated Alq3 nanowires

Science.gov (United States)

Khan, Mohammad Bilal; Ahmad, Sultan; Parwaz, M.; Rahul, Khan, Zishan H.

2018-05-01

We report the synthesis and characterization of pure and Au incorporated Alq3 nanowires. These nanowires are synthesized using thermal vapor transport method. The luminescence intensity of Au incorporated Alq3 nanowires are recorded to be higher than that of pure Alq3 nanowires, which is found to increase with the increase in Au concentration. Fluorescence quenching is also observed when Au concentration is increased beyond the certain limit.

Synthesis and Characterization of Highly Intercalated Graphite Bisulfate

Science.gov (United States)

Salvatore, Marcella; Carotenuto, Gianfranco; De Nicola, Sergio; Camerlingo, Carlo; Ambrogi, Veronica; Carfagna, Cosimo

2017-03-01

Different chemical formulations for the synthesis of highly intercalated graphite bisulfate have been tested. In particular, nitric acid, potassium nitrate, potassium dichromate, potassium permanganate, sodium periodate, sodium chlorate, and hydrogen peroxide have been used in this synthesis scheme as the auxiliary reagent (oxidizing agent). In order to evaluate the presence of delamination, and pre-expansion phenomena, and the achieved intercalation degree in the prepared samples, the obtained graphite intercalation compounds have been characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray powder diffraction (XRD), infrared spectroscopy (FT-IR), micro-Raman spectroscopy ( μ-RS), and thermal analysis (TGA). Delamination and pre-expansion phenomena were observed only for nitric acid, sodium chlorate, and hydrogen peroxide, while the presence of strong oxidizers (KMnO4, K2Cr2O7) led to stable graphite intercalation compounds. The largest content of intercalated bisulfate is achieved in the intercalated compounds obtained from NaIO4 and NaClO3.

Functional Characterization of the Canine Heme-Regulated eIF2α Kinase: Regulation of Protein Synthesis

Directory of Open Access Journals (Sweden)

Kimon C. Kanelakis

2009-01-01

Full Text Available The heme-regulated inhibitor (HRI negatively regulates protein synthesis by phosphorylating eukaryotic initiation factor-2α (eIF2α thereby inhibiting protein translation. The importance of HRI in regulating hemoglobin synthesis in erythroid cells makes it an attractive molecular target in need of further characterization. In this work, we have cloned and expressed the canine form of the HRI kinase. The canine nucleotide sequence has 86%, 82%, and 81% identity to the human, mouse, and rat HRI, respectively. It was noted that an isoleucine residue in the ATP binding site of human, rat, and mouse HRI is replaced by a valine in the canine kinase. The expression of canine HRI protein by in vitro translation using wheat germ lysate or in Sf9 cells using a baculovirus expression system was increased by the addition of hemin. Following purification, the canine protein was found to be 72 kD and showed kinase activity determined by its ability to phosphorylate a synthetic peptide substrate. Quercetin, a kinase inhibitor known to inhibit mouse and human HRI, inhibits canine HRI in a concentration-dependent manner. Additionally, quercetin is able to increase de novo protein synthesis in canine reticulocytes. We conclude that the canine is a suitable model species for studying the role of HRI in erythropoiesis.

Synthesis and characterization of TiO2/Ag/polymer ternary nanoparticles via surface-initiated atom transfer radical polymerization

International Nuclear Information System (INIS)

Park, Jung Tae; Koh, Joo Hwan; Seo, Jin Ah; Cho, Yong Soo; Kim, Jong Hak

2011-01-01

We report on the novel ternary hybrid materials consisting of semiconductor (TiO 2 ), metal (Ag) and polymer (poly(oxyethylene methacrylate) (POEM)). First, a hydrophilic polymer, i.e. POEM, was grafted from TiO 2 nanoparticles via the surface-initiated atom transfer radical polymerization (ATRP) technique. These TiO 2 -POEM brush nanoparticles were used to template the formation of Ag nanoparticles by introduction of a AgCF 3 SO 3 precursor and a NaBH 4 aqueous solution for reduction process. Successful grafting of polymeric chains from the surface of TiO 2 nanoparticles and the in situ formation of Ag nanoparticles within the polymeric chains were confirmed using transmission electron microscopy (TEM), UV-vis spectroscopy, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). FT-IR spectroscopy also revealed the specific interaction of Ag nanoparticles with the C=O groups of POEM brushes. This study presents a simple route for the in situ synthesis of both metal and polymer confined within the semiconductor, producing ternary hybrid inorganic-organic nanomaterials.

Green synthesis and characterization of graphene nanosheets

Energy Technology Data Exchange (ETDEWEB)

Tavakoli, Farnosh [School of Chemistry, College of Science, University of Tehran, Tehran (Iran, Islamic Republic of); Salavati-Niasari, Masoud, E-mail: salavati@kashanu.ac.ir [Institute of Nano Science and Nano Technology, University of Kashan, Kashan, P. O. Box. 87317-51167, Islamic Republic of Iran (Iran, Islamic Republic of); Department of Inorganic Chemistry, Faculty of Chemistry, University of Kashan, Kashan, P. O. Box. 87317-51167, Islamic Republic of Iran (Iran, Islamic Republic of); Badiei, Alireza [School of Chemistry, College of Science, University of Tehran, Tehran (Iran, Islamic Republic of); Mohandes, Fatemeh [Department of Inorganic Chemistry, Faculty of Chemistry, University of Kashan, Kashan, P. O. Box. 87317-51167, Islamic Republic of Iran (Iran, Islamic Republic of)

2015-03-15

Highlights: • For the first time, we have synthesized graphene nanosheets in the presence of pomegranate juice. • Here pomegranate juice was used not only as reductant but also as capping agent. • FT-IR, XRD, SEM, EDS and TEM were used to characterize the samples. • According to TEM image, graphene nanosheet is individually exfoliated after stirring for 24 h. • As shown in the TEM image, graphene monolayer is obtained. - Abstract: For the first time, we have successfully synthesized graphene nanosheets in the presence of pomegranate juice. In this approach, pomegranate juice was used not only as reductant but also as capping agent to form graphene nanosheets. At first, the improved Hummer method to oxidize graphite for the synthesis of graphene oxide (GO) was applied, and then the as-produced graphene oxide was reduced by pomegranate juice to form graphene nanosheets. Fourier transformed infrared (FT-IR), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), high resolution transmission electron microscopy (HRTEM), atomic force microscopy (AFM) and raman were used to characterize the samples. The results obtained from the characterization techniques proved high purity of the final products.

Green synthesis and characterization of graphene nanosheets

International Nuclear Information System (INIS)

Tavakoli, Farnosh; Salavati-Niasari, Masoud; Badiei, Alireza; Mohandes, Fatemeh

2015-01-01

Highlights: • For the first time, we have synthesized graphene nanosheets in the presence of pomegranate juice. • Here pomegranate juice was used not only as reductant but also as capping agent. • FT-IR, XRD, SEM, EDS and TEM were used to characterize the samples. • According to TEM image, graphene nanosheet is individually exfoliated after stirring for 24 h. • As shown in the TEM image, graphene monolayer is obtained. - Abstract: For the first time, we have successfully synthesized graphene nanosheets in the presence of pomegranate juice. In this approach, pomegranate juice was used not only as reductant but also as capping agent to form graphene nanosheets. At first, the improved Hummer method to oxidize graphite for the synthesis of graphene oxide (GO) was applied, and then the as-produced graphene oxide was reduced by pomegranate juice to form graphene nanosheets. Fourier transformed infrared (FT-IR), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), high resolution transmission electron microscopy (HRTEM), atomic force microscopy (AFM) and raman were used to characterize the samples. The results obtained from the characterization techniques proved high purity of the final products

Synthesis of (/sup 3/H) Zolpidem

Energy Technology Data Exchange (ETDEWEB)

Allen, J.; Parent, G.; Tizot, A.

1986-08-01

Zolpidem is a novel hypnotic agent possessing a substituted imidazo (1,2-a) pyridine structure. The synthesis of the tritium labelled compound with a specific activity of 60.5 Ci/mmol is described. This new radioligand was initially used to establish and characterize the binding properties of Zolpidem in the rat brain.

Synthesis, purification and characterization of [3,5 - T] p-aminobenzoic acid

International Nuclear Information System (INIS)

Corol-Cucu, Delia-Irina; Chiper, Diana; Mihaila, V.; Negoita, N.

2000-01-01

This paper refers to the synthesis, purification and characterization of [3,5-T] p-aminobenzoic acid (PAB,H' vitamine). The p-aminobenzoic acid is used in the treatment of rheumatic arthritis and dermatological affections. The advantage of tritium labelling of p-aminobenzoic acid is that some biomedical important aspects of collagen's behaviour are made clear. The PAB stimulate the grow of intestinal bacteria so necessary to synthesis of some vitamins (bio tine, pantothenic acid). Tritium is the only radioactive isotope of hydrogen. Several steps have to be carried out in the synthesis of the final product as well as to study its biological behavior. For the labelling of PAB one prefers the substitution of bromine from PAB-3,5-Br with tritium because of simplicity of reaction and the easy synthesis of halogen compound. The first step in synthesis is the protection of NH 2 group through acetylation of PAB. After that PAB is bromated into the 3 and 5 position with elementary bromine. The raw compound is purified and recrystallized and characterized through thin layer chromatography.The tritium labelling is performed through substitution of bromine from bromate derivative, using Pd/C (10% Pd) as catalyst and low basic conditions for the neutralization of HBr resulting from reaction. After the separation of PAB-3,5-T through filtration, the catalyst remains on the filter paper and the labelled compound goes in aqueous solution. PAB-3,5-T is purified through thin layer chromatography with the solvent system n-BuOH:NH 4 OH(25%):H 2 O:EtOH (8:1:2:2,5, v/v) with silica gel GF 254 as support. The determination of activity is carried out with LSC (Liquid Scintillation Counter). A 98% purity was determined through TLC in the same conditions while determination of activity distribution was performed with a 2π Berthold scanner with gas running and without window. The chemical concentration has been measured through UV spectrophotometry and by comparing extinction with

Sol – Gel synthesis and characterization of magnesium peroxide nanoparticles

International Nuclear Information System (INIS)

Jaison, J; Chan, Y S; Ashok raja, C; Balakumar, S

2015-01-01

Magnesium peroxide is an excellent source of oxygen in agriculture applications, for instance it is used in waste management as a material for soil bioremediation to remove contaminants from polluted underground water, biological wastes treatment to break down hydrocarbon, etc. In the present study, sol-gel synthesis of magnesium peroxide (MgO 2 ) nanoparticles is reported. Magnesium peroxide is odourless; fine peroxide which releases oxygen when reacts with water. During the sol-gel synthesis, the magnesium malonate intermediate is formed which was then calcinated to obtain MgO 2 nanoparticles. The synthesized nanoparticles were characterized using Thermo gravimetric -Differential Thermal Analysis (TG- DTA), X-Ray Diffraction studies (XRD) and High Resolution Transmission Electron Microscope (HRTEM). Our study provides a clear insight that the formation of magnesium malonate during the synthesis was due to the reaction between magnesium acetate, oxalic acid and ethanol. In our study, we can conclude that the calcination temperature has a strong influence on particle size, morphology, monodispersity and the chemistry of the particles. (paper)

Synthesis and Characterization of Block Copolymers with Unique Chemical Functionalities and Entropically-Hindering Moieties

Science.gov (United States)

2017-08-14

methanol as a function of chemistry , morphology and hydration levels. Accomplishments: This section is included in the "upload" section. Training...Copolymer Blend Membranes.” In Press, Polymer Engineering and Science, DOI: 10.1002 /pen.24508, 2017. 5. M. Pérez-Pérez and D. Suleiman. “Synthesis and...Synthesis and Characterization of Sulfonated Amine Block Copolymers for Energy Efficient Applications". Chemical Engineering Symposium, University of

Synthesis and characterization of tantalum organometallic complexes. Catalytic activity for olefins

International Nuclear Information System (INIS)

Baley, A.S.

1990-11-01

Synthesis of monoaryloxy (alcoxy) neopentyl compounds is investigated. The tantalum-oxygen bond is formed by two parallel ways from TaCl 5 or TaR 2 Cl 3 with R = neopentyl and the tantalum carbon bond from a neopentyl derivative of the main series. Some compounds were isolated and characterized by NMR, elemental analysis and sometimes X-ray structure, some others are characterized in solution only. Catalytic effect is tested by ethylene dimerization and olefin polymerization. Reactivity of tantalum aryloxy neopentyl in respect to complexing and chelating ligands is studied for preparation of neopentylidene complexes

Synthesis and characterization of mangan oxide coated sand from Capkala kaolin

Science.gov (United States)

Destiarti, Lia; Wahyuni, Nelly; Prawatya, Yopa Eka; Sasri, Risya

2017-03-01

Synthesis and characterization of mangan oxide coated sand from quartz sand fraction of Capkala kaolin has been conducted. There were two methods on synthesis of Mangan Oxide Coated Sand (MOCS) from Capkala Kaolin compared in this research. Characterization of MOCS was done by using Scanning Electron Microscope/Energy Dispersive X-Ray Spectrometer (SEM/EDX) and X-Ray Diffraction (XRD). The MOCS was tested to reduce phosphate in laundry waste. The result showed that the natural sand had bigger agregates and a relatively uniform structural orientation while both MOCS had heterogen structural orientation and manganese oxide formed in cluster. Manganese in first and second methods were 1,93% and 2,63%, respectively. The XRD spectrum showed clear reflections at 22,80°, 36,04°, 37,60° and a broad band at 26,62° (SiO2). Based on XRD spectrum, it can be concluded that mineral constituents of MOCS was verified corresponding to pyrolusite (MnO2). The former MOCS could reduce almost 60% while the later could reduce 70% phosphate in laundry waste.

Synthesis and characterization of anisotropic magnetic hydrogels

Energy Technology Data Exchange (ETDEWEB)

Hinrichs, Stephan, E-mail: stephan.hinrichs@chemie.uni-hamburg.de; Nun, Nils; Fischer, Birgit, E-mail: birgit.fischer@chemie.uni-hamburg.de

2017-06-01

Multiresponsive hydrogels are an interesting new class of materials. They offer the advantage, that they respond to different stimuli like temperature, pH and magnetic fields. By this they can change their properties which makes the hydrogels ideal candidates for many applications in the technical as well as medical field. Here we present the synthesis and characterization of hydrogels - micro- as well as macrogels - which consist of an iron oxide core, varying in phase and morphology, embedded in a thermoresponsive polymer, consisting of poly N-isopropylacrylamide. By using dynamic light scattering we investigated the thermoresponsive properties. In addition we were able to follow the formation of the macrogel by monitoring the shear viscosity.

Octalithium plumbate as breeding blanket ceramic: Neutronic performances, synthesis and partial characterization

International Nuclear Information System (INIS)

Colominas, S.; Palermo, I.; Abellà, J.; Gómez-Ros, J.M.; Sanz, J.; Sedano, L.

2012-01-01

Highlights: ► Definition of a suitable configuration for the Li 8 PbO 6 breeding blanket design. ► Demonstration of the feasibility of Li 8 PbO 6 as a breeding material. ► Synthesis optimization in the Li 8 PbO 6 production. ► Characterization of Li 8 PbO 6 by X-ray phase analysis is discussed. - Abstract: A neutronic assessment of the performances of a helium-cooled Li 8 PbO 6 breeding blanket (BB) for the conceptual design of a DEMO fusion reactor is given. Different BB configurations have been considered in order to minimize the amount of beryllium required for neutron multiplication, including the use of graphite as reflector material. The calculated neutronic responses: tritium breeding ratio (TBR), power deposition in TF coils and power amplification factor, indicate the feasibility of Li 8 PbO 6 as breeding material. Furthermore, the synthesis and characterization of Li 8 PbO 6 by X-ray phase analysis are also discussed.

Colloidal synthesis and characterization of Bi2S3 nanoparticles for photovoltaic applications

International Nuclear Information System (INIS)

Piras, R; Aresti, M; Saba, M; Marongiu, D; Mula, G; Quochi, F; Mura, A; Bongiovanni, G; Cannas, C; Mureddu, M; Ardu, A; Ennas, G; Musinu, A; Calzia, V; Mattoni, A

2014-01-01

Bismuth sulfide is a promising n-type semiconductor for solar energy conversion. We have explored the colloidal synthesis of Bi 2 S 3 nanocrystals, with the aim of employing them in the fabrication of solution-processable solar cells and to replace toxic heavy metals chalcogenides like PbS or CdS, that are currently employed in such devices. We compare different methods to obtain Bi 2 S 3 colloidal quantum dots, including the use of environmentally benign reactants, through organometallic synthesis. Different sizes and shapes were obtained according to the synthesis parameters and the growth process has been rationalized by comparing the predicted morphology with systematic physical-chemistry characterization of nanocrystals by X-ray diffraction, FT-IR spectroscopy, Transmission Electron Microscopy (TEM)

Synthesis and characterization of dihexyldithiocarbamate as a chelating agent in extraction of gold(III)

Energy Technology Data Exchange (ETDEWEB)

Fatimah, Soja Siti, E-mail: soja-sf@upi.edu [Departemen Pendidikan Kimia, Universitas Pendidikan Indonesia, Jl. Dr. Setiabudhi No. 229, Bandung 40154 (Indonesia); Department of Chemistry, Faculty of Mathematics and Natural Sciences, Padjadjaran University, Jl. Raya Bandung-Sumedang, Km. 21, Jatinangor (Indonesia); Bahti, Husein H.; Hastiawan, Iwan [Department of Chemistry, Faculty of Mathematics and Natural Sciences, Padjadjaran University, Jl. Raya Bandung-Sumedang, Km. 21, Jatinangor (Indonesia); Permanasari, Anna [Departemen Pendidikan Kimia, Universitas Pendidikan Indonesia, Jl. Dr. Setiabudhi No. 229, Bandung 40154 (Indonesia)

2016-02-08

The use of dialkyldithiocarbamates as chelating agents of transition metals have been developing for decades. Many chelating agents have been synthesized and used in the extraction of the metals. Studies on particular aspects of extraction of the metals, such as the effect of increasing hydrophobicity of chelating agents on the effectiveness of the extraction, have been done. However, despite the many studies on the synthesis and applications of this type of chelating agents, interests in the aspect of molecular structure of the synthesized ligands and of their complexes, have been limited. This study aimed at synthesizing and characterizing dihexylthiocarbamate, and using the ligand for the extraction of gold III). Characterization of the ligand and of its metal complex were done by using elemental analysis, DTG, and spectroscopic methods to include NMR, ({sup 1}H, and {sup 13}C), FTIR, and MS-ESI. Data on the synthesis, characterization, and the application of the ligand as a chelating agent are presented.

Synthesis and characterization of dihexyldithiocarbamate as a chelating agent in extraction of gold(III)

Science.gov (United States)

Fatimah, Soja Siti; Bahti, Husein H.; Hastiawan, Iwan; Permanasari, Anna

2016-02-01

The use of dialkyldithiocarbamates as chelating agents of transition metals have been developing for decades. Many chelating agents have been synthesized and used in the extraction of the metals. Studies on particular aspects of extraction of the metals, such as the effect of increasing hydrophobicity of chelating agents on the effectiveness of the extraction, have been done. However, despite the many studies on the synthesis and applications of this type of chelating agents, interests in the aspect of molecular structure of the synthesized ligands and of their complexes, have been limited. This study aimed at synthesizing and characterizing dihexylthiocarbamate, and using the ligand for the extraction of gold III). Characterization of the ligand and of its metal complex were done by using elemental analysis, DTG, and spectroscopic methods to include NMR, (1H, and 13C), FTIR, and MS-ESI. Data on the synthesis, characterization, and the application of the ligand as a chelating agent are presented.

Synthesis and Characterization of Colloidal Metal and Photovoltaic Semiconductor Nanocrystals

KAUST Repository

Abulikemu, Mutalifu

2014-11-05

Metal and semiconducting nanocrystals have received a great deal of attention from fundamental scientists and application-oriented researchers due to their physical and chemical properties, which differ from those of bulk materials. Nanocrystals are essential building blocks in the development of nanostructured devices for energy conversion. Colloidal metals and metal chalcogenides have been developed for use as nanocrystal inks to produce efficient solar cells with lower costs. All high-performing photovoltaic nanocrystals contain toxic elements, such as Pb, or scarce elements, such as In; thus, the production of solution-processable nanocrystals from earth-abundant materials using environmentally benign synthesis and processing methods has become a major challenge for the inorganic semiconductor-based solar field. This dissertation, divided into two parts, addresses several aspects of these emerging challenges. The first portion of the thesis describes the synthesis and characterization of nanocrystals of antimony sulfide, which is composed of non-scarce and non-toxic elements, and examines their performance in photovoltaic devices. The effect of various synthetic parameters on the final morphology is explored. The structural, optical and morphological properties of the nanocrystals were investigated, and Sb2S3 nanocrystal-based solid-state semiconductor-sensitized solar cells were fabricated using different deposition processes. We achieved promising power conversion efficiencies of 1.48%. The second part of the thesis demonstrates a novel method for the in situ synthesis and patterning of nanocrystals via reactive inkjet printing. The use of low-cost manufacturing approaches for the synthesis of nanocrystals is critical for many applications, including photonics and electronics. In this work, a simple, low-cost method for the synthesis of nanocrystals with minimum size variation and waste using reactive inkjet printing is introduced. As a proof of concept, the

Designing Selectivity in Metal-Semiconductor Nanocrystals: Synthesis, Characterization, and Self-Assembly

Science.gov (United States)

Pavlopoulos, Nicholas George

This dissertation contains six chapters detailing recent advances that have been made in the synthesis and characterization of metal-semiconductor hybrid nanocrystals (HNCs), and the applications of these materials. Primarily focused on the synthesis of well-defined II-VI semiconductor nanorod (NR) and tetrapod (TP) based constructs of interest for photocatalytic and solar energy applications, the research described herein discusses progress towards the realization of key design rules for the synthesis of functional semiconductor nanocrystals (NCs). As such, a blend of novel synthesis, advanced characterization, and direct application of heterostructured nanoparticles are presented. The first chapter is a review summarizing the design, synthesis, properties, and applications of multicomponent nanomaterials composed of disparate semiconductor and metal domains. By coupling two compositionally distinct materials onto a single nanocrystal, synergistic properties can arise that are not present in the isolated components, ranging from self-assembly to photocatalysis. For semiconductor nanomaterials, this was first realized in the ability to tune nanomaterial dimensions from 0-D quantum dot (QD) structures to cylindrical (NR) and branched (TP) structures by exploitation of advanced colloidal synthesis techniques and understandings of NC facet reactivities. The second chapter is focused on the synthesis and characterization of well-defined CdSe-seeded-CdS (CdSe CdS) NR systems synthesized by overcoating of wurtzite (W) CdSe quantum dots with W-CdS shells. 1-dimensional NRs have been interesting constructs for applications such as solar concentrators, optical gains, and photocatalysis. Through synthetic control over CdSe CdS NR systems, materials with small and large CdSe seeds were prepared, and for each seed size, multiple NR lengths were prepared. Through transient absorption studies, it was found that band alignment did not affect the efficiency of charge localization

Synthesis and characterization of M-type barium hexferrite by ultrasonic inter-dispersion of chemical precipitate

International Nuclear Information System (INIS)

Garcia Junior, E.S.; Gomes Junior, G.G.; Ogasawara, T.

2010-01-01

This work is concerned with the study the synthesis and characterization of M-type barium hexaferrite powder by chemical precipitation type and ultrasonic interdispersion of precursor materials Fe(OH) 3 and Ba(OH) 2 ,separately and ultrasonic inter-dispersion, followed by drying and calcining. In order to guide the experimental work was carried out a preliminary thermodynamic analysis of the system Ba-Fe-H 2 O at 25 deg C. The study shows that the phase formation of M-type barium hexaferrite is obtained at a calcination at 1000 deg C, characterized by X-ray diffraction, the grain growth of the final product of synthesis depending on the calcination temperature is visible by SEM. The synthesis method developed in this research is an option to achieve the results that would be obtained if the co-precipitation of ferric and barium hydroxide was thermodynamically possible, where you can get crystallization of barium hexaferrite in a calcination at 1000 deg C. (author)

Rotavirus NSP2 interferes with the core lattice protein VP2 in initiation of minus-strand synthesis

International Nuclear Information System (INIS)

Vende, Patrice; Tortorici, M. Alejandra; Taraporewala, Zenobia F.; Patton, John T.

2003-01-01

The rotavirus nonstructural protein NSP2 self-assembles into stable octameric structures that possess nonspecific affinity for single-stranded (ss)RNA and RNA-RNA helix-destabilizing and NTPase activities. Furthermore, NSP2 is a component of replication intermediates with replicase activity and plays a critical role in the packaging and replication of the segmented dsRNA genome of rotavirus. To better understand the function of the protein in genome replication, we examined the effect that purified recombinant NSP2 had on the synthesis of dsRNA by the open core replication system. The results showed that NSP2 inhibited the synthesis of dsRNA from viral mRNA in vitro, in a concentration-dependent manner. The inhibition was overcome by adding increasing amounts of viral mRNA or nonviral ssRNA to the system, indicating that the inhibition was mediated by the nonspecific RNA-binding activity of NSP2. Further analysis revealed that NSP2 interfered with the ability of the open core proteins, GTP, and viral mRNA to form the initiation complex for (-) strand synthesis. Additional experiments indicated that NSP2 did not perturb recognition of viral mRNA by the viral RNA polymerase VP1, but rather interfered with the function of VP2, a protein that is essential for (-) strand initiation and dsRNA synthesis and that forms the T = 1 lattice of the virion core. In contrast to initiation, NSP2 did not inhibit (-) strand elongation. Collectively, the findings provide evidence that the temporal order of interaction of RNA-binding proteins with viral mRNA is a crucial factor impacting the formation of replication intermediates

Poly(glycidyl methacrylate) grafted CdSe quantum dots by surface-initiated atom transfer radical polymerization: Novel synthesis, characterization, properties, and cytotoxicity studies

Energy Technology Data Exchange (ETDEWEB)

Bach, Long Giang; Islam, Md. Rafiqul [Department of Imaging System Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of); Lee, Doh Chang [Department of Chemical and Biomolecular Engineering, KAIST Institute for the Nanocentury (KINC), Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701 (Korea, Republic of); Lim, Kwon Taek, E-mail: ktlim@pknu.ac.kr [Department of Imaging System Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of)

2013-10-15

A novel approach for the synthesis of poly(glycidyl methacrylate) grafted CdSe quantum dot (QDs) (PGMA-g-CdSe) was developed. The PGMA-g-CdSe nanohybrids were synthesized by the surface-initiated atom transfer radical polymerization of glycidyl methacrylate from the surface of the strategic initiator, CdSe-BrIB QDs prepared by the interaction of 2-bromoisobutyryl bromide (BrIB) and CdSe-OH QDs. The structure, morphology, and optical property of the PGMA-g-CdSe nanohybrids were analyzed by FT-IR, XPS, TGA, XRD, TEM, and PL. The as-synthesized PGMA-g-CdSe nanohybrids having multi-epoxide groups were employed for the direct coupling of biotin via ring-opening reaction of the epoxide groups to afford the Biotin-f-PGMA-g-CdSe nanobioconjugate. The covalent immobilization of biotin onto PGMA-g-CdSe was confirmed by FT-IR, XPS, and EDX. Biocompatibility and imaging properties of the Biotin-f-PGMA-g-CdSe were investigated by MTT bioassay and PL analysis, respectively. The cell viability study suggested that the biocompatibility was significantly enhanced by the functionalization of CdSe QDs by biotin and PGMA.

Poly(glycidyl methacrylate) grafted CdSe quantum dots by surface-initiated atom transfer radical polymerization: Novel synthesis, characterization, properties, and cytotoxicity studies

International Nuclear Information System (INIS)

Bach, Long Giang; Islam, Md. Rafiqul; Lee, Doh Chang; Lim, Kwon Taek

2013-01-01

A novel approach for the synthesis of poly(glycidyl methacrylate) grafted CdSe quantum dot (QDs) (PGMA-g-CdSe) was developed. The PGMA-g-CdSe nanohybrids were synthesized by the surface-initiated atom transfer radical polymerization of glycidyl methacrylate from the surface of the strategic initiator, CdSe-BrIB QDs prepared by the interaction of 2-bromoisobutyryl bromide (BrIB) and CdSe-OH QDs. The structure, morphology, and optical property of the PGMA-g-CdSe nanohybrids were analyzed by FT-IR, XPS, TGA, XRD, TEM, and PL. The as-synthesized PGMA-g-CdSe nanohybrids having multi-epoxide groups were employed for the direct coupling of biotin via ring-opening reaction of the epoxide groups to afford the Biotin-f-PGMA-g-CdSe nanobioconjugate. The covalent immobilization of biotin onto PGMA-g-CdSe was confirmed by FT-IR, XPS, and EDX. Biocompatibility and imaging properties of the Biotin-f-PGMA-g-CdSe were investigated by MTT bioassay and PL analysis, respectively. The cell viability study suggested that the biocompatibility was significantly enhanced by the functionalization of CdSe QDs by biotin and PGMA.

Synthesis and characterization of covalent diphenylalanine nanotube-folic acid conjugates

DEFF Research Database (Denmark)

León, John Jairo Castillo; Rindzevicius, Tomas; Wu, Kaiyu

2014-01-01

Herein, we describe the synthesis and characterization of a covalent nanoscale assembly formed between diphenylalanine micro/nanotubes (PNT) and folic acid (FA). The conjugate was obtained via chemical functionalization through coupling of amine groups of PNTs and carboxylic groups of FA. The sur...... for applications in the detection and diagnosis of cancer or tropical diseases such as leishmaniasis and as a carrier nanosystem delivering drugs to malignant tumors that overexpress folate receptors....

Synthesis and Characterization of Magnesium Substituted Aluminophosphate Molecular Sieves with AEL Structure

Institute of Scientific and Technical Information of China (English)

Benjing Xu; Ling Qian; Xinmei Liu; Chunmin Song; Zifeng Yan

2004-01-01

MAPO-11 molecular sieves were synthesized by hydrothermal methods. The influence of precursor of magnesium, Mg/Al ratio, synthesis temperature, synthesis time and the type of template on the formation and properties of MAPO-11 molecular sieves was examined. The samples were characterized by the techniques of X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric/differential thermogravimetric analysis (TG-DGA), etc. The results show that the shape and size of crystal were influenced by the precursor of Mg, the Mg/Al ratio and the type of template, and the TG-DGA analysis shows that MAPO-11 molecular sieves as-synthesized have poor thermal stability.

Synthesis and characterization of hydroxyapatite crystals: a review study on the analytical methods

NARCIS (Netherlands)

Koutsopoulos, S.

2002-01-01

For the synthesis of hydroxyapatite crystals from aqueous solutions three preparation methods were employed. From the experimental processes and the characterization of the crystals it was concluded that aging and precipitation kinetics are critical for the purity of the product and its

High temperature bismuth cuprate superconductors synthesis and characterization

International Nuclear Information System (INIS)

Mansori, M.; Satre, P.; Breandon, C.; Roubin, M.; Sebaoun, A.

1993-01-01

High temperature superconductor phases synthesis by coprecipitation in alkaline solution is reported. (Bi 1.6 Pb 0.4 )Sr 2 Ca 1 Cu 2 O 8+x and (Bi 1.6 Pb 0.4 )Sr 2 Ca 2 Cu 3 O 10+y noted (2212) and (2223) have been prepared and studied. From aqueous nitrate solutions of Bi, Pb, Sr, Ca and Cu and oxalic acid aqueous solution as well as ethylene glycol, using an organic base (the triethylamine), the pH was increased up to the path of the precipitation zone (pH = 10.5-11.2). This method assures a good granulometric homogeneity of powders. Thermal analysis and characterization of the different components produced during the synthesis have been studied by DTA (differential thermal analysis)- TGA (thermogravimetric analysis), X-ray diffraction at different temperatures and by Infrared spectroscopy with a Fourier transformation. The measurements of magnetic susceptibility for the 2212 (with and without lead) and 2223 (with lead) phases have permitted us to observe the critical temperatures of 84 K, 87 K and 114 K. (author). 29 refs., 2 figs., 4 tabs

Synthesis and characterization of fluorine compounds

International Nuclear Information System (INIS)

Martinez Carrillo, M.

1991-01-01

The ( 18 F) D-glucose, 2-deoxy fluorine ( 18 FDG) is a radio pharmaceutic that is used in nuclear medicine it is utilized mainly in the glucose metabolism. It allows recently to observe the tumors accumulation and growing. The obtention of this radio pharmaceutic can realize by a nucleophilic or electrophilic process through the use of different fluorinated agents obtained as intermediates for introducing the 18 F radionuclide in a final step of synthesis. The first methods already has been studied in the National Institute of Nuclear Research. The second one which is based this work and it was realized through the reaction of acetyl hypo fluorite (CH 3 COOF) with tri acetyl glucal (TAG) in turn they require the obtention of several fluorated compounds that they serve as intermediates for their obtention so that objective of this work was to find the adequate technique for the obtention of anhydride hydrofluoric acid (HF), KF.2 HF and elemental fluorine so as the design and construction of the systems and equipment used for carry out each one of the reactions. Moreover it was designed the system that will be used for the obtention of acetyl hypo fluoride and the synthesis of composite tetraacetilide 3,4,6 tri-D-glucopyranosil fluoride (TAG-F) for that finally by hydrolysis it was obtained the 2-deoxy fluoride-D-glucose (TAG) in inactive. In this system were realized several preliminary tests. The results are showed in the content of this work also the techniques for compounds characterization were given. (Author)

SYNTHESIS OF STYRENE-BUTADIENE STATISTIC COPOLYMERS CONTAINING MAGNESIUM INITIATOR

Directory of Open Access Journals (Sweden)

A. V. Firsova

2015-01-01

Full Text Available The article discusses the use of organomagnesium initiators in the synthesis of styrene-butadiene random copolymer (SBR obtained solution polymerization and their influence on the properties of rubber. Selected organic magnesium dialkyl initiator is combined with a modifier, which is a mixed alkoxide of an alkali and alkaline earth metals, which allows to control the micr ostructure of the diene polymer and its molecular weight characteristics. Alcohol derivatives selected high-boiling alcohols tetra (hydroxypropyl ethylenediamine (lapromol 294 and tetrahydrofurfuryl alcohol (TGFS. Selection of high-boiling alcohols due to the fact that the destruction of alkoxide with aqueous polymer degassing they do not fall into the return solvent and almost fall into the exact water. The metal components of alkoxides are lithium, sodium, potassium, magnesium and calcium. The resulting solutions are stable when stored modifier t hroughout the year even at -40 °C. The scheme of obtaining the new catalyst systems based organomagnesium and alcoxide of alkali and alkaline earth metals, which yields as functionalized SBR with a statistical and a distribution block of butadiene and styrene was developed. The process of copolymerization with styrene to butadiene organomagnesium initiators as using an organolithium compound (n-butyllithium was carried out, and without it. Found that the addition of n-butyllithium in the reaction mixture leads to a sharp increase in the rate of reaction. The results of studies of the effect of composition of the initiator system on the structure of diene polymers. It was revealed that a mixed initiator system affords a high conversion of monomers (to 90 % in 1 hour 1,2-polybutadiene content increased to 60 %. The process of polymerization of only a mixture of organomagnesium initiators and alcoxide of alkali and alkaline earth metals are not actively proceeds, conversion of the monomers reaches to 90 % in 4 hours, the microstructure

Synthesis characterization, and properties of rubber lattices; a review

International Nuclear Information System (INIS)

Khan, S.M.; Chughtai, A.; Sattar, A.

2008-01-01

Latex is a stable dispersion of polymeric material in an aqueous medium. Lattices are present in natural as well as in synthetic forms. The range of applications of latex is extensive in carpet underlay, fabric back-coating, paper and paints coatings, adhesive, binder, leather finish, floor polish, waterproof clothing, bounded fiber, pigment printing, latex thread, cement and asphalt, foam scraps binders, can closure, thickeners, box toes and shoes counters, sealant and mastics, modifiers, protein reduction, enzyme treatment and peroxide vulcanization. In this review we are presenting synthesis, characterization, properties, manufacturing and processing of latex. (author)

Boronate esters: Synthesis, characterization and molecular base receptor analysis

Science.gov (United States)

Gómez-Jaimes, Gelen; Barba, Victor

2014-10-01

The synthesis of three boronate esters obtained by reacting 4-fluorophenylboronic (1), 4-iodophenylboronic (2) and 3,4-chlorophenylboronic (3) acids with 2,4,5-trihidroxybenzaldehyde is reported. The structural characterization was determined by spectroscopic and spectrometric techniques. The boron atom was evaluated to acts as Lewis acid center in the reaction with pyridine (Py), triethylamine (TEA) and fluoride anion (F-). The titration method was followed by UV-Vis and 11B NMR spectroscopy; results indicate the good interaction with the fluoride ion but poor coordination towards pyridine in solution.

Synthesis and Characterization of Biscoumarin and Benzopyrano Dicoumarin Derivatives

International Nuclear Information System (INIS)

Nik Khairunissa' Nik Abdullah Zawawi; Muhammad Taha; Norizan Ahmat; Nor Hadiani Ismail; Nik Khairunissa' Nik Abdullah Zawawi; Muhammad Taha; Norizan Ahmat; Nor Hadiani Ismail

2016-01-01

The wide-ranging biological activities of 4-hydroxycoumarin have stimulated considerable interest in this class of compounds, and various biscoumarin derivatives have been synthesized. Recently, a number of methods have been reported for the synthesis of biscoumarin by the reaction of 4-hydroxycoumarin and various aldehydes in the presence of catalysts. In the present study, a new series of biscoumarin and benzopyrano dicoumarin were synthesized and physically characterized by nuclear magnetic resonane ( 1 H and 13 C NMR), fourier transform infrared spectroscopy (FTIR), mass spectrometry (MS) and melting point. (author)

Synthesis and characterization of the polyaniline dopant Schiff base

Directory of Open Access Journals (Sweden)

Mirian Y. Matsumoto

2012-06-01

Full Text Available The Schiff base, N-salicilidenoanilina was used as dopant to induce polymerization of aniline and thus preparing polyaniline (PAni. The different conditions of preparation, including Schiff base structure, and the dosage of acidity reaction medium, were investigated to discuss the influence of these conditions relative conductivity of the resulting samples. The products were also characterized by Fourier transform infrared (FTIR, ultraviolet-visible (UV-Vis, electrochemical impedance spectroscopy (EIE. The results showed the synthesis conditions play an important in the formation and the final properties of the polyaniline

Synthesis, structure characterization and catalytic activity of nickel tungstate nanoparticles

International Nuclear Information System (INIS)

Pourmortazavi, Seied Mahdi; Rahimi-Nasrabadi, Mehdi; Khalilian-Shalamzari, Morteza; Zahedi, Mir Mahdi; Hajimirsadeghi, Seiedeh Somayyeh; Omrani, Ismail

2012-01-01

Graphical abstract: NiWO 4 nanoparticles were prepared via precipitation technique. Experimental parameters of procedure were optimized statistically. Highlights: ► NiWO 4 spherical nanoparticles were synthesized via direct precipitation method. ► Taguchi robust design was used for optimization of synthesis reaction parameters. ► Composition and structural properties of NiWO 4 nanoparticles were characterized. ► EDAX, XRD, SEM, FT-IR, UV–vis and photoluminescence techniques were employed. ► Catalytic activity of the product in a cyclo-addition reaction was investigated. - Abstract: Taguchi robust design was applied to optimize experimental parameters for controllable, simple and fast synthesis of nickel tungstate nanoparticles. NiWO 4 nanoparticles were synthesized by precipitation reaction involving addition of nickel ion solution to the tungstate aqueous reagent and then formation of nickel tungstate nucleolus which are insoluble in aqueous media. Effects of various parameters such as nickel and tungstate concentrations, flow rate of reagent addition and reactor temperature on diameter of synthesized nickel tungstate nanoparticles were investigated experimentally by the aid of orthogonal array design. The results for analysis of variance (ANOVA) showed that particle size of nickel tungstate can be effectively tuned by controlling significant variables involving nickel and tungstate concentrations and flow rate; while, temperature of the reactor has a no considerable effect on the size of NiWO 4 particles. The ANOVA results proposed the optimum conditions for synthesis of nickel tungstate nanoparticles via this technique. Also, under optimum condition nanoparticles of NiWO 4 were prepared and their structure and chemical composition were characterized by means of EDAX, XRD, SEM, FT-IR spectroscopy, UV–vis spectroscopy, and photoluminescence. Finally, catalytic activity of the nanoparticles in a cycloaddition reaction was examined.

Synthesis, structure characterization and catalytic activity of nickel tungstate nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Pourmortazavi, Seied Mahdi, E-mail: pourmortazavi@yahoo.com [Faculty of Material and Manufacturing Technologies, Malek Ashtar University of Technology, Tehran (Iran, Islamic Republic of); Rahimi-Nasrabadi, Mehdi, E-mail: rahiminasrabadi@gmail.com [Department of Chemistry, Imam Hossein University, Tehran (Iran, Islamic Republic of); Khalilian-Shalamzari, Morteza [Department of Chemistry, Imam Hossein University, Tehran (Iran, Islamic Republic of); Zahedi, Mir Mahdi; Hajimirsadeghi, Seiedeh Somayyeh [Islamic Azad University, Varamin Pishva Branch, Varamin (Iran, Islamic Republic of); Omrani, Ismail [Department of Chemistry, Imam Hossein University, Tehran (Iran, Islamic Republic of)

2012-12-15

Graphical abstract: NiWO{sub 4} nanoparticles were prepared via precipitation technique. Experimental parameters of procedure were optimized statistically. Highlights: Black-Right-Pointing-Pointer NiWO{sub 4} spherical nanoparticles were synthesized via direct precipitation method. Black-Right-Pointing-Pointer Taguchi robust design was used for optimization of synthesis reaction parameters. Black-Right-Pointing-Pointer Composition and structural properties of NiWO{sub 4} nanoparticles were characterized. Black-Right-Pointing-Pointer EDAX, XRD, SEM, FT-IR, UV-vis and photoluminescence techniques were employed. Black-Right-Pointing-Pointer Catalytic activity of the product in a cyclo-addition reaction was investigated. - Abstract: Taguchi robust design was applied to optimize experimental parameters for controllable, simple and fast synthesis of nickel tungstate nanoparticles. NiWO{sub 4} nanoparticles were synthesized by precipitation reaction involving addition of nickel ion solution to the tungstate aqueous reagent and then formation of nickel tungstate nucleolus which are insoluble in aqueous media. Effects of various parameters such as nickel and tungstate concentrations, flow rate of reagent addition and reactor temperature on diameter of synthesized nickel tungstate nanoparticles were investigated experimentally by the aid of orthogonal array design. The results for analysis of variance (ANOVA) showed that particle size of nickel tungstate can be effectively tuned by controlling significant variables involving nickel and tungstate concentrations and flow rate; while, temperature of the reactor has a no considerable effect on the size of NiWO{sub 4} particles. The ANOVA results proposed the optimum conditions for synthesis of nickel tungstate nanoparticles via this technique. Also, under optimum condition nanoparticles of NiWO{sub 4} were prepared and their structure and chemical composition were characterized by means of EDAX, XRD, SEM, FT-IR spectroscopy, UV

Synthesis and characterization of high performance superabsorbent hydrogels using bis[2-(methacryloyloxyethyl] phosphate as crosslinker

Directory of Open Access Journals (Sweden)

A. A. L. Goncalves

2016-03-01

Full Text Available Various superabsorbent polymers (SAPs were synthesized by free radical copolymerization at 70°C using acrylic acid (AA, potassium acrylate (KA, N-isopropyl acrylamide (NIPAM and sulfopropyl methacrylate potassium salt (SPM as monomers, bis[2-(methacryloyloxyethyl] phosphate (BMEP as crosslinker and potassium persulfate (KPS as initiator. The optimization of the synthesis led to the preparation of a SAP with very high water absorption ability, with a maximum swelling of 2618 g water/g dry hydrogel. The most promising SAP was fully characterized and the absorption capacities were studied at different pH and ionic strengths. When this SAP was mixed with soil, the mixture was able to lose water more slowly. Also, this material revealed high loading capacity and showed good releasing profiles using urea as model fertilizer. Due to these advantageous properties, the synthesized SAP can be used in agricultural applications.

Synthesis, characterization and magnetic properties of room-temperature nanofluid ferromagnetic graphite

OpenAIRE

Souza, N. S.; Sergeenkov, S.; Speglich, C.; Rivera, V. A. G.; Cardoso, C. A.; Pardo, H.; Mombru, A. W.; Rodrigues, A. D.; de Lima, O. F.; Araujo-Moreira, F. M.

2009-01-01

We report the chemical synthesis route, structural characterization, and physical properties of nanofluid magnetic graphite (NFMG) obtained from the previously synthesized bulk organic magnetic graphite (MG) by stabilizing the aqueous ferrofluid suspension with an addition of active cationic surfactant. The measured magnetization-field hysteresis curves along with the temperature dependence of magnetization confirmed room-temperature ferromagnetism in both MG and NFMG samples. (C) 2009 Americ...

Electrochemical synthesis and characterization of copper (I oxide

Directory of Open Access Journals (Sweden)

Bugarinović Sanja J.

2009-01-01

Full Text Available The quest and need for clean and economical energy sources have increased interest in the development of thin film cells technologies. Electrochemical deposition is an attractive method for synthesis of thin films. It offers the advantages of low synthesis temperature, low cost and high purity. Copper (I oxide or cuprous oxide is an oxide semiconductor which is used as the anodic material in the form of thin film in lithium batteries and solar cells. The cathodic process of synthesis of cuprous oxide thin film is carried out in a potentiostatic mode from the organic electrolyte. The process parameters are chosen in that way to accomplish maximum difference between the potentials at which Cu2O and CuO are obtained. The electrochemical characterization was carried out by cyclic voltammetry. The electrodeposition techniques are particularly well suited for the deposition of single elements but it is also possible to carry out simultaneous depositions of several elements and syntheses of well-defined alternating layers of metals and oxides with thicknesses down to a few nm. Nanomaterials exhibit novel physical properties and play an important role in fundamental research. In addition, cuprous oxide is commonly used as a pigment, a fungicide, and an antifouling agent for marine paints. It is insoluble in water and organic solvents. This work presents the examinations of the influence of bath, temperature, pH and current density on the characteristics of electrochemically synthesized cuprous oxide. In the 'classic' process of synthesis, which is carried out under galvanostatic conditions on the anode, the grain size of the powder decreases with the increase in current density while the grain colour becomes lighter. The best commercial quality of the Cu2O (grain size, colour, content of choride was obtained at the temperature of 80°C, concentration of NaCl of 3 mol/dm3 and current density of 400 A/m2.

Synthesis and Characterization of Thermoelectric Oxides at Macro- and Nano-scales

Science.gov (United States)

Ma, Feiyue

Thermoelectric materials can directly convert a temperature difference into electrical voltage and vice versa. Due to this unique property, thermoelectric materials are widely used in industry and scientific laboratories for temperature sensing and thermal management applications. Waste heat harvesting, another potential application of thermoelectric materials, has long been limited by the low conversion efficiency of the materials. Potential high temperature applications, such as power plant waste heat harvesting and combustion engine exhaust heat recovery, make thermoelectric oxides a very promising class of thermoelectric materials. In this thesis, the synthesis and characterization of thermoelectric oxide materials are explored. In the first part of this thesis, the measurement methodologies and instrumentation processes employed to investigate different thermoelectric properties, such as the Seebeck coefficient and carrier concentration at the bulk scale and the thermal conductivity at the nanoscale, are detailed. Existing scientific and engineering challenges associated with these measurements are also reviewed. To overcome such problems, original parts and methodologies have been designed. Three fully functional systems were ultimately developed for the characterization of macroscale thermoelectric properties as well as localized thermal conductivity. In the second part of the thesis, the synthesis of NaxCo 2O4, a thermoelectric oxide material, is discussed. Modification of both composition and structure were carried out so as to optimize the thermoelectric performance of NaxCo2O4. Nanostructuring methods, such as ball milling, electrospinning, auto-combustion synthesis, and core-shell structure fabrication, have been developed to refine the grain size of NaxCo2O4 in order to reduce its thermal conductivity. However, the structure of the nanostructured materials is very unstable at high temperature and limited improvement on thermoelectric performance is

Synthesis, characterization and use of ATRP bifunctional initiator with trichloromethyl end-groups

Czech Academy of Sciences Publication Activity Database

Toman, Luděk; Janata, Miroslav; Spěváček, Jiří; Masař, Bohumil; Vlček, Petr; Látalová, Petra

2002-01-01

Roč. 43, č. 2 (2002), s. 18-19 ISSN 0032-3934 R&D Projects: GA ČR GA203/01/0513 Institutional research plan: CEZ:AV0Z4050913 Keywords : bifunctional initiator * ATRP polymerization * trichloromethyl end-groups Subject RIV: CD - Macromolecular Chemistry

Synthesis and characterization of a novel laser ablation sensitive triazene incorporated epoxy resin

KAUST Repository

Patole, Archana S.

2014-01-01

New triazene monomer was synthesized and further employed as a crosslinking agent partner with epoxy matrix using ethyl methyl imidazole as a curing agent in order to investigate the effect of triazene moieties on polymeric properties for laser ablation application. The synthesized triazene monomer was characterized by analytical and spectroscopic methods, while the surface morphology of resist after laser ablation was visualized by optical laser scanning images and scanning electron microscopy. Thermogravimetrical investigations indicate the loss of nitrogen being the initial thermal decomposition step and exhibit sufficient stabilities for the requirements for laser ablation application. Fourier transform infra-red, nuclear magnetic resonance, and gas chromatography analyses showed the successful synthesis of triazene. The ablation results from the optical laser scanning images revealed that the etching depth could be controlled by varying the concentration of triazene monomer in the formulation of epoxy. The shear strength analysis revealed that that the shear strength increased with increasing the amount of triazene in the formulation of direct ablation sensitive resist. © 2014 The Korean Institute of Metals and Materials and Springer Science+Business Media Dordrecht.

Synthesis and Characterization of High Aluminum Zeolite X from Technical Grade Materials

Directory of Open Access Journals (Sweden)

Seyed Kamal Masoudian

2013-06-01

Full Text Available Zeolites are widely used as ion exchangers, adsorbents, separation materials and catalyst due to their well-tailored and highly-reproducible structures; therefore, the synthesis of zeolite from low grade resources can be interested. In the present work, high aluminum zeolite X was prepared from mixing technical grade sodium aluminate and sodium silicate solutions at temperatures between 70°C and 100°C. The synthesized zeolite X was characterized by SEM and X-ray methods according to ASTM standard procedures. The results showed that aging of the synthesis medium at the room temperature considerably increased the selectivity of zeolite X formation. On the other hand, high temperature of reaction mixture during crystallization formed zeolite A in the product; therefore, it decreased the purity of zeolite X. In addition, it was found that increasing H2O/Na2O and decreasing Na2O/SiO2 molar ratios in the reaction mixture resulted product with higher purity. © 2013 BCREC UNDIP. All rights reservedReceived: 7th January 2013; Revised: 7th April 2013; Accepted: 19th April 2013[How to Cite: Masoudian, S. K., Sadighi, S., Abbasi, A. (2013. Synthesis and Characterization of High Alu-minum Zeolite X from Technical Grade Materials. Bulletin of Chemical Reaction Engineering & Catalysis, 8 (1: 54-60. (doi:10.9767/bcrec.8.1.4321.54-60][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.8.1.4321.54-60] | View in  |

New Dilated LMI Characterization for the Multiobjective Full-Order Dynamic Output Feedback Synthesis Problem

Directory of Open Access Journals (Sweden)

Zrida Jalel

2010-01-01

Full Text Available This paper introduces new dilated LMI conditions for continuous-time linear systems which not only characterize stability and performance specifications, but also, performance specifications. These new conditions offer, in addition to new analysis tools, synthesis procedures that have the advantages of keeping the controller parameters independent of the Lyapunov matrix and offering supplementary degrees of freedom. The impact of such advantages is great on the multiobjective full-order dynamic output feedback control problem as the obtained dilated LMI conditions always encompass the standard ones. It follows that much less conservatism is possible in comparison to the currently used standard LMI based synthesis procedures. A numerical simulation, based on an empirically abridged search procedure, is presented and shows the advantage of the proposed synthesis methods.

Green approach for the synthesis and characterization of ZrSnO4 nanopowder

Science.gov (United States)

Athar, Taimur; Vishwakarma, Sandeep Kumar; Bardia, Avinash; Alabass, Razzaq; Alqarlosy, Ahmed; Khan, Aleem Ahmed

2016-06-01

Well-defined structural framework of ZrSnO4 nanopowder has been synthesized for the fabrications of cost-effective and sensitive devices which give final reproducible result with reliability under ideal conditions. The synthesis was carried out at moderate temperature and then finally dried in the laboratory oven and then followed with calcination at 1000 °C for 4 h to get phase selective product. It was observed that gelation time depends on the concentration of reactants and temperature. The characterization of ZrSnO4 was carried out with XRD, SEM, TEM, UV, thermal analysis, DLS and FT-IR techniques. With adjustment of reaction parameters, the systematic tuning of the particle size, shape and functional properties can be controlled. It was concluded that self-assembly is an integral part for the synthesis and opens a new exciting opportunity for better understanding the formation of nanostructure framework from micro- to nanoscale along with mechanistic via wet chemical approach. ZrSnO4 has vital role in identifying its potential cytotoxicity in the biological systems. The cytotoxicity effects of ZrSnO4 nanopowder in vitro were evaluated in three different human cell types (hepatocytes, mesenchymal stem cells and neuronal cells). Acute exposure of nanoparticles was found to have greater cytotoxic effect at higher concentration (30 µg/ml). However, partial detoxification was observed during nanoparticles exposure at day 6. The study concluded that an initial stress from nanoparticles incorporates sealing or detoxification of nanoparticles which may help to recover cell viability.

Synthesis and characterization of boron nitrides nanotubes

International Nuclear Information System (INIS)

Ferreira, T.H.; Sousa, E.M.B.

2010-01-01

This paper presents a new synthesis for the production of boron nitride nanotubes (BNNT) from boron powder, ammonium nitrate and hematite tube furnace CVD method. The samples were subjected to some characterization techniques as infrared spectroscopy, thermal analysis, X-ray diffraction and scanning electron microscopy and transmission. By analyzing the results can explain the chemical reactions involved in the process and confirm the formation of BNNT with several layers and about 30 nanometers in diameter. Due to excellent mechanical properties and its chemical and thermal stability this material is promising for various applications. However, BNNT has received much less attention than carbon nanotubes, it is because of great difficulty to synthesize appreciable quantities from the techniques currently known, and this is one of the main reasons this work.(author)

Magnetic ionic liquids: synthesis and characterization

International Nuclear Information System (INIS)

Medeiros, Anderson M.M.S.; Parize, Alexandre L.; Oliveira, Vanda M.; Neto, Brenno A.D.; Rubim, Joel C.

2010-01-01

The synthesis of magnetic ionic liquids (MILs) based on the stable dispersions of magnetic nanoparticles (MNPs) of γ-Fe 2 O 3 , Fe 3 O 4 , and CoFe 2 O 4 in the ionic liquid 1-n-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMI.NTf 2 ) is reported. The MNPs were obtained by the coprecipitation method. The surface of the α-Fe 2 O 3 , Fe 3 O 4 , and CoFe 2 O 4 MNPs with mean sizes (XRD) of 9.3, 12.3, and 11.0 nm, respectively were functionalized by 1-n-butyl-3-(3'-trimethoxypropylsilane)- imidazolium chloride. The non functionalized and functionalized MNPs were further characterized by Raman, FTIR-ATR, and FTNIR spectroscopy and by TGA. The stability of the MILs was assigned to the formation of at least one monolayer of the surface modifier agent that mimics the structure of the BMI.NTf 2 IL. (author)

Controlling Magnetic and Ferroelectric Order Through Geometry: Synthesis, Ab Initio Theory, Characterization of New Multi-Ferric Fluoride Materials

Energy Technology Data Exchange (ETDEWEB)

Halasyamani, Shiv [Univ. of Houston, TX (United States); Fennie, Craig [Cornell Univ., Ithaca, NY (United States)

2016-11-03

We have focused on the synthesis, characterization, and ab initio theory on multi-functional mixed-metal fluorides. With funding from the DOE, we have successfully synthesized and characterized a variety of mixed metal fluoride materials.

Synthesis and characterization of iron-cobalt (FeCo) alloy nanoparticles supported on carbon

DEFF Research Database (Denmark)

Koutsopoulos, Sotiris; Barfod, Rasmus; Eriksen, Kim Michael

2017-01-01

of the alloy nanoparticles differed depending on the preparation method. When the wet impregnation technique of acetate precursor salts of Fe and Co were used for the synthesis, the size of FeCo alloy nanoparticles was approximately 13 nm. FeCo alloy nanoparticles were characterized by crystallography (XRD...

Synthesis, purification and physico-chemical characterization of the deuterized chloroform

International Nuclear Information System (INIS)

Mihaila, Vasile; Chiper, Diana

1999-01-01

This work refers to deuterized chloroform synthesis and purification methods. Three preparation methods of deuterized chloroform are presented. In the first method the direct chlorination of methane (CH 4 + 3Cl 2 ) in the presence of light and in an oxygen-free atmosphere results in CHCl 3 + 3HCl. The method's drawback is that the resulting product is impure, being obtained also secondary chlorinated compounds, such as CHCl, CH 2 Cl 2 and CCl 4 . The second method consists in chlorination of acetaldehyde or acetone, in basic catalysis and in halogen excess (α substitution with direct synthesis of trihalogen compound), followed by a haloform reaction (hydrolytic splitting) in the presence of chlorinated lime. This method makes use of decarbolyzing of trichlor acetate acid (as a sodium salt), what results in CL 3 CH + NaHCO 3 . This method is the most suitable for the deuterized chloroform synthesis, since the reaction takes place in absence of other hydrogen atoms (protons) and in deuterized water of 99.87% purity, according to the following reaction: Cl 3 C-COONa → (D 2 O) → Cl 2 CD + NaDCO 3 . Another advantage is that this method avoids the synthesis of secondary products, which could entail additional purifications (distillations, rectification, a.s.o.). The deuterized chloroform is separated from the deuterized sodium bicarbonate aqueous solution by washing with deuterized water, in a liquid to liquid separating funnel. After separation, deuterized chloroform is dried in nitrogen atmosphere. The characterization of the final product is carried out by nuclear magnetic resonance spectrometry. (authors)

Chemical synthesis, characterization and evaluation of antimicrobial properties of Cu and its oxide nanoparticles

CSIR Research Space (South Africa)

Motlatle, Abesach M

2016-10-01

Full Text Available of Nanoparticle Research, vol. 18: DOI: 10.1007/s11051-016-3614-8 Chemical synthesis, characterization and evaluation of antimicrobial properties of Cu and its oxide nanoparticles Motlatle AM Kesevan Pillai S Scriba MR Ray SS ABSTRACT: Cu...

Synthesis and characterization of new polyamino-cyclodextrin materials.

Science.gov (United States)

Lo Meo, Paolo; D'Anna, Francesca; Gruttadauria, Michelangelo; Riela, Serena; Noto, Renato

2012-01-10

With the aim of the synthesis of chemically modified cyclodextrins bearing polyamine pendant groups, potentially useful as capping agents for the preparation of nanosized metal systems or as auxiliaries for gene transfection, the reaction between the heptakis-(6-iodo)-(6-deoxy)-β-cyclodextrin and various polyamines has been explored. This synthetic approach allows obtaining materials constituted by mixtures of cyclodextrins, having different degrees of substitution, which were satisfactorily characterized by means of various complementary techniques (ESI-MS, NMR, potentiometric titration). The products obtained were successfully subjected to preliminary tests for their binding abilities towards suitable organic guests and as capping agents for the preparation of stable silver nanoparticles. Copyright © 2011 Elsevier Ltd. All rights reserved.

Nano-ilmenite FeTiO3 : synthesis and characterization

OpenAIRE

Raghavender, A. T.; Hoa Hong, Nguyen; Lee, Kyu Joon; Jung, Myung-Hwa; Skoko, Z.; Vasilevskiy, Mikhail; Cerqueira, M. F.; Samantilleke, A. P.

2013-01-01

In general, ilmenite FeTiO3 is synthesized by solid-state reaction at very high pressure and high temperature. Synthesis of FeTiO3 is not an easy task as the Fe2+ ions are not stable. Therefore, it is really challenging to prepare this material. In this work nano-ilmenite FeTiO3 was synthesized by the sol-gel method. Structural, optical and magnetic characterizations were performed. The bandgap of FeTiO3 was determined to be 2.8 eV showing FeTiO3 as suitable wide bandgap material for technolo...

Synthesis and characterization of N-t-BOC protected pyrrole-sulfur oligomers and polymers

NARCIS (Netherlands)

Groenendaal, L.; Pieterse, K.; Vekemans, J.A.J.M.; Meijer, E.W.

1997-01-01

The synthesis and characterization of a new class of pyrrole-sulfur compounds is described. These compounds are designed to be precursors for an organic analogue of poly(sulfur nitride). Poly(N-t-BOC-2.5-pyrrolyl sulfide) was prepared from N-t-BOC-2,5-dibromopyrrole by first lithiating this compound

Chemical Reduction Synthesis of Iron Aluminum Powders

Science.gov (United States)

Zurita-Méndez, N. N.; la Torre, G. Carbajal-De; Ballesteros-Almanza, L.; Villagómez-Galindo, M.; Sánchez-Castillo, A.; Espinosa-Medina, M. A.

In this study, a chemical reduction synthesis method of iron aluminum (FeAl) nano-dimensional intermetallic powders is described. The process has two stages: a salt reduction and solvent evaporation by a heat treatment at 1100°C. The precursors of the synthesis are ferric chloride, aluminum foil chips, a mix of Toluene/THF in a 75/25 volume relationship, and concentrated hydrochloric acid as initiator of the reaction. The reaction time was 20 days, the product obtained was dried at 60 °C for 2 h and calcined at 400, 800, and 1100 °C for 4 h each. To characterize and confirm the obtained synthesis products, X-Ray Diffraction (XRD), and Scanning Electron Microscopy (SEM) techniques were used. The results of morphology and chemical characterization of nano-dimensional powders obtained showed a formation of agglomerated particles of a size range of approximately 150 nm to 1.0 μm. Composition of powders was identified as corundum (Al2O3), iron aluminide (FeAl3), and iron-aluminum oxides (Fe0. 53Al0. 47)2O3 phases. The oxide phases formation were associated with the reaction of atmospheric concentration-free oxygen during synthesis and sintering steps, reducing the concentration of the iron aluminum phase.

Synthesis and characterization of copper nanoparticles by using the exploding wire method

International Nuclear Information System (INIS)

Das, Rashmita; Das, Basanta Kumar; Shyam, Anurag

2012-01-01

During the past few years, the synthesis of copper nanoparticles has attracted much attention because of their huge potential for replacing the expensive nano silver inks utilized in conductive printing. This opens a new possibility in printed electronics. Copper-based inkjet inks can be used to form various devices such as solar cells, RF identification tags and electroluminescence devices. This paper describes controlled synthesis of pure copper nanoparticles, mainly by using the exploding wire method. A wire of 0.26 mm in diameter was exploded in a nitrogen environment. The sample was characterized by using X-ray diffraction (XRD) and atomic force microscopy (AFM). XRD revealed the presence of pure copper and AFM revealed the presence of nanoparticles with an average size of 55 nm.

Synthesis of Zinc Diethyldithiocarbamate (ZDEC) and Structure Characterization using Decoupling 1H NMR

International Nuclear Information System (INIS)

Sujarit, Jenjira; Phutdhawong, Weerachai

2003-10-01

A synthesis of zinc diethyldithiocarbamate (ZDEC) has been studied. The optimization mole ratio of the synthetic process was 2: 2: 2: 1 of diethylamine, carbondisulfide, sodium hydroxide, and zinc chloride. Characterization was carried out mainly by analyzing its spectroscopic properties especially decoupling 1 H NMR technique. ZDEC was obtained in 48.5% yield

Design, synthesis, and characterization of novel fine-particle, unsupported catalysts for coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Klein, M.T.

1991-12-30

The purpose of this work is to investigate the kinetics-assisted design, synthesis and characterization of fme-pardcle, unsupported catalysts for coal liquefaction. The goal is to develop a fundamental understanding of coal catalysis and catalysts that will, in turn, allow for the specification of a novel optimal catalyst for coal liquefaction.

Synthesis and characterization of a cerebral radiotracer

International Nuclear Information System (INIS)

Ben hamouda, Salem

2010-01-01

The development of nuclear medicine is based on research of new radiopharmaceuticals, in particular, relying on technetium-99m, the most used radioisotope in terms of availability and low cost. A similar study on Rhenium (185/187Re) is essential for monitoring physico-chemical studies due to the high specific activity of technetium-99m. During this work, we have synthesized and labeled with technetium the N-methyl-4-hydroxy piperidinyl ferrocenyl carboxylate. The marking is done by exchange of ligands between the iron group of ferrocene and tricabonyl technetium core. We have succeeded to synthesis the N-methyl-4-hydroxy piperidinyl carboxyl cyclopentadienyl tricarbonyl rhenium (the molecular analogue of the technetium). We characterized it by MS, IR and NMR (1H, 13C) The structure of N-methyl-4-hydroxy piperidinyl carboxyl cyclopentadienyl tricarbonyl technetium is well justified.

PAMAM dendrimer-coated iron oxide nanoparticles: synthesis and characterization of different generations

International Nuclear Information System (INIS)

Khodadust, Rouhollah; Unsoy, Gozde; Yalcın, Serap; Gunduz, Gungor; Gunduz, Ufuk

2013-01-01

This study focuses on the synthesis and characterization of different generations (G 0 –G 7 ) of polyamidoamine (PAMAM) dendrimer-coated magnetic nanoparticles (DcMNPs). In this study, superparamagnetic iron oxide nanoparticles were synthesized by co-precipitation method. The synthesized nanoparticles were modified with aminopropyltrimethoxysilane for dendrimer coating. Aminosilane-modified MNPs were coated with PAMAM dendrimer. The characterization of synthesized nanoparticles was performed by X-ray diffraction, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), dynamic light scattering, and vibrating sample magnetometry (VSM) analyses. TEM images demonstrated that the DcMNPs have monodisperse size distribution with an average particle diameter of 16 ± 5 nm. DcMNPs were found to be superparamagnetic through VSM analysis. The synthesis, aminosilane modification, and dendrimer coating of iron oxide nanoparticles were validated by FTIR and XPS analyses. Cellular internalization of nanoparticles was studied by inverted light scattering microscopy, and cytotoxicity was determined by XTT analysis. Results demonstrated that the synthesized DcMNPs, with their functional groups, symmetry perfection, size distribution, improved magnetic properties, and nontoxic characteristics could be suitable nanocarriers for targeted cancer therapy upon loading with various anticancer agents.

Initial Identification and Characterization of an Emerging Zoonotic Influenza Prior to Pandemic Spread

Science.gov (United States)

2010-11-01

equally closely strains of both H1N2 influenza A virus of swine origin and H3N2 influenza A virus of avian origin. The expected matches for each of...Naval Health Research Center Initial Identification and Characterization of an Emerging Zoonotic Influenza Virus Prior to Pandemic Spread...10.1128/JCM.01336-10 PMCID: PMC3020883 Initial Identification and Characterization of an Emerging Zoonotic Influenza Virus Prior to Pandemic

Synthesis and Characterization of Nano Scale YBCO

International Nuclear Information System (INIS)

Sukirman, E.; Wisnu AA; Yustinus P; Sahidin W, D.; Rina M, Th.

2009-01-01

Synthesis and characterization of the nano scale YBCO superconductor have been performed. The nano scale superconductor was synthesized from YBCO system (YBa 2 Cu 3 O 7-X ). Raw materials, namely Y 2 O 3 , BaCO 3 , and Cu°, were balanced and mixed with ethanol using magnetic steering as a churn in a beaker glass. Then, the precursor was calcined at T k = 900°C for 5 hours and repeated it until three times. The resulting precursor was ground by using High Energy Milling (HEM) for t = 0, 30, 50, 70, and 90 hour and hereinafter precursors are successively referred as YKM-00, YKM-30, YKM-50, YKM-70, and YKM-90. The resulting powders phase were characterized by means of x-ray diffraction technique using the Rietveld analysis method. Precursor of YKM-90 was pressed into pellets, and then sintered at various temperatures and periods. The sample phase was then characterized by using the Rietveld analysis method based on the x-ray diffraction data. The crystallites size were calculated using Scherrer formula. Results of analysis indicate that by minimizing crystallites size, period of sinter can be shortened from 10 to 1 hour, resulting crystallite size of D = 925 Å, critical current density of J c = 4 A / cm 2 , and can be grown of about 15 weight % of 211-phase in a matrix of 123-phase. The decrease of crystallite size will generate a change in physical properties dramatically, if the crystallite size of the material, D is smaller or equal to the coherence length of 10 Å. (author)

Synthesis and characterization of ruthenium-decorated nanoporous platinum materials

International Nuclear Information System (INIS)

Peng Xinsheng; Koczkur, Kallum; Chen, Aicheng

2007-01-01

We report on the synthesis of novel three-dimensional nanoporous Pt-Ru bimetallic networks by decorating nanoporous Pt networks with Ru using a hydrothermally assisted precipitating process. Scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) were used to characterize the morphology and the composition of the nanoporous Pt-Ru networks formed. X-ray diffraction analysis confirmed that, after protected annealing treatment, Pt-Ru bimetallic material was formed. The electrocatalytic activity of the synthesized nanoporous Pt-Ru networks was characterized using electrochemical oxidation of methanol as a probe. The electrocatalytic activity of the nanoporous Pt networks significantly increases with the increments of decorated Ru and reaches the highest value with 41% of Ru. The peak current of methanol oxidation on the nanoporous Pt-Ru(41%) bimetallic networks is over 180% higher than that on the nanoporous Pt networks without Ru decoration. This is very desirable for fuel cell development and electrochemical sensor design

Synthesis and characterization of cobalt sulfide nanoparticles by sonochemical method

Science.gov (United States)

Muradov, Mustafa B.; Balayeva, Ofeliya O.; Azizov, Abdulsaid A.; Maharramov, Abel M.; Qahramanli, Lala R.; Eyvazova, Goncha M.; Aghamaliyev, Zohrab A.

2018-03-01

Convenient and environmentally friendly synthesis of Co9S8/PVA, CoxSy/EG and CoxSy/3-MPA nanocomposites were carried out in the presence of ultrasonic irradiation by the liquid phase synthesis of the sonochemical method. For the synthesis, cobalt acetate tetrahydrate [Co(CH3COO)2·4H2O] and sodium sulfide (Na2S·9H2O) were used as a cobalt and sulfur precursor, respectively. Polyvinyl alcohol (PVA), ethylene glycol (EG) and 3-mercaptopropionic acid (3-MPA) were used as a capping agent and surfactant. The structural, optical properties and morphology of nanocomposites were characterized using X-ray diffractometer (XRD), Ultraviolet/Visible Spectroscopy (UV-Vis), Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The optical band gap of Co9S8/PVA is 1.81 eV and for CoxSy/EG is 2.42 eV, where the direct band gap of bulk cobalt sulfide is (0.78-0.9 eV). The wide band gap indicates that synthesised nanocomposites can be used in the fabrication of optical and photonic devices. The growth mechanisms of the Co9S8, CoS2 and Co3S4 nanoparticles were discussed by the reactions. The effects of sonication time and annealing temperature on the properties of the nanoparticles have been studied in detail.

Synthesis and Physicochemical Characterization of Mesoporous SiO2 Nanoparticles

Directory of Open Access Journals (Sweden)

Dharani Das

2014-01-01

Full Text Available There exists a knowledge gap in understanding potential toxicity of mesoporous silica nanoparticles. A critical step in assessing toxicity of these particles is to have a wide size range with different chemistries and physicochemical properties. There are several challenges when synthesizing mesoporous silica nanoparticles over a wide range of sizes including (1 nonuniform synthesis protocols using the same starting materials, (2 the low material yield in a single batch synthesis (especially for particles below 60–70 nm, and (3 morphological instability during surfactant removal process and surface modifications. In this study, we synthesized a library of mesoporous silica nanoparticles with approximate particle sizes of 25, 70, 100, 170, and 600 nm. Surfaces of the silica nanoparticles were modified with hydrophilic-CH2–(CH22–COOH and relatively hydrophobic-CH2–(CH210–COOH functional groups. All silica nanoparticles were analysed for morphology, surface functionality, surface area/pore volume, surface organic content, and dispersion characteristics in liquid media. Our analysis revealed the synthesis of a spectrum of monodisperse bare and surface modified mesoporous silica nanoparticles with a narrow particle size distribution and devoid of cocontaminants critical for toxicity studies. Complete physicochemical characterization of these synthetic mesoporous silica nanoparticles will permit systematic toxicology studies for investigation of structure-activity relationships.

Effects of (monomer - crosslinker – initiator) composition during non imprinted polymers synthesis for catechin retention

Science.gov (United States)

Triadhi, U.; Zulfikar, M. A.; Setiyanto, H.; Amran, M. B.

2018-05-01

MISPE (molecularly imprinted Solid Phase Extraction) is a separation technique using a solid adsorbent as a principle of MI (molecularly imprinted). Methacrylic acid (MAA) was used as a monomer, ethylene glycol dimethacrylate (EGDMA) as a crosslinker, benzoyl peroxide (BPO) as an initiator and acetonitrile (ACN) as a porogen. Catechin will be used as the template. Thermal and microwave methods were employed in the synthesis method. When analyzed using FTIR spectra, it was found that there were no significant differences between NIP (non-imprinted polymer) resulting from thermal method and that resulting from microwave method. Preparation of polymers by microwave method required 4 mins at 60-65 °C, significantly less than thermal method, that took 60 minutes at the same temperature. The variations of mole ratios of the monomer, the crosslinker, and the initiator were also performed. Based on the FTIR spectra, intensity of some peaks were changed due to the decreases of concentration. The optimum composition for NIP synthesis was MAA: EGDMA: BPO ratio of 5:30:0.5 (in mmole). The TGA curve showed that the NIP sythesized using microwave method experienced mass loss of around 98.50% at 604.8 °C.

Synthesis and Characterization of C-Cinnamal Calix [4] Resorsinarena from Cinnamon Oil Waste West Sumatra

Science.gov (United States)

Etika, S. B.; Nasra, E.; Rilaztika, I.

2018-04-01

Synthesis and characterization of compound C-Cinnamal Calix [4] Resorsinarena (CCCR) of cinnamon oil waste have been done. This study was aimed to synthesis and characterize C-Cinnamal Calix [4] Resorsinarena from cinnamaldehyde violated cinnamon oil waste. C-Cinnamal Calix [4] Resorsinarena was synthesized by electrophilic substitution reaction of cinnamaldehyde isolated by the acid and resorcinol at 77oC temperature for 2 hour. The data analysis spectrum UV-VIS and FT-IR showed that the compound isolated cinnamaldehyde same as pure cinnamaldehyde compound. The characterization of C-Cinnamal Calix [4] Resorsinarena in the form of reddish-colored solids with melting point 3580C by using UV-VIS showed the presence of double bond, FT-IR showed the absorption at the wave number 3323,94 cm-1 indicating the ‑OH group, the wave number 1610,94 cm-1 showed the vibration C=C, the strong region absorption of 1500,86 cm-1 indicating the presence of an aromatic ring, the at 1442,88 cm-1 wave number indicating the presence of CH3.

Synthesis and characterization of nanocomposites ZnO / polypyrrole for anti corrosive application

International Nuclear Information System (INIS)

Valenca, D.P.; Bouchonneau, N.; Vieira, M.R.S.; Alves, K.G.B.; Melo, C.P. de; Urtiga Filho, S.L.

2014-01-01

Nanoparticles of metal oxides and conductive polymers have been investigated as alternative additives in corrosion protection of oxidizable metals. In this hybrid nanocomposites work Polypyrrole-ZnO were synthesized and characterized as a potential application as industrial paint anti corrosive additive. The different steps of the synthesis and characterization of nanocomposites are described. The nanocomposites were obtained from the emulsion polymerization of aqueous solutions of pyrrole and sodium dodecyl sulfate containing ZnO nanoparticles dispersed in the mass. The nanoparticles were characterized by scanning electron microscopy and transmission, dynamic light scattering, diffraction of X-rays and techniques of infrared spectroscopy. From the characterization techniques, it was possible to determine the average size of nanoparticles of ZnO and ZnO-Polypyrrole. The peaks in the diffraction pattern of X-rays observed in the nanocomposite were the same as in ZnO, confirming the presence of ZnO in the composite. (author)

Synthesis, Characterization, and Ultrafast Dynamics of Metal, Metal Oxide, and Semiconductor Nanomaterials

OpenAIRE

Wheeler, Damon Andreas

2013-01-01

SYNTHESIS, CHARACTERIZATION, AND ULTRAFAST DYNAMICS OF METAL, METAL OXIDE, AND SEMICONDUCTOR NANOMATERIALSABSTRACTThe optical properties of each of the three main classes of inorganic nanomaterials, metals, metal oxides, and semiconductors differ greatly due to the intrinsically different nature of the materials. These optical properties are among the most fascinating and useful aspects of nanomaterials with applications spanning cancer treatment, sensors, lasers, and solar cells. One techn...

Self-Assembled Structures of PMAA-PMMA Block Copolymers : Synthesis, Characterization, and Self-Consistent Field Computations

NARCIS (Netherlands)

Li, Feng; Schellekens, Mike; de Bont, Jens; Peters, Ron; Overbeek, Ad; Leermakers, Frans A. M.; Tuinier, Remco

2015-01-01

Block copolymers composed of methacrylic acid (MAA) and methyl methacrylate (MMA) blocks are interesting candidates for replacing surfactants in emulsion polymerization methods. Here the synthesis and experimental characterization of well-defined PMAA-PMMA block copolymers made via RAFT

Self-assembled structures of PMAA-PMMA block copolymers: Synthesis, characterization, and self-consistent field computations

NARCIS (Netherlands)

Li, F.; Schellekens, J.; Bont, de J.A.M.; Peters, R.; Overbeek, A.; Leermakers, F.A.M.; Tuinier, R.

2015-01-01

Block copolymers composed of methacrylic acid (MAA) and methyl methacrylate (MMA) blocks are interesting candidates for replacing surfactants in emulsion polymerization methods. Here the synthesis and experimental characterization of well-defined PMAA–PMMA block copolymers made via RAFT

Synthesis, characterization and optimization of poly(p-phenylenediamine)-based organoclay composite for Cr(VI) remediation

CSIR Research Space (South Africa)

Mdlalose, L

2017-04-01

Full Text Available of these materials for environmental remediation. We report here the synthesis, characterization and application of a poly(para-phenylenediamine) (poly-pPD) organoclay-based composite for removal of Cr(VI) complexes from wastewater. Adsorption capacity...

Synthesis and characterization of related substances of Azilsartan Kamedoxomil

Directory of Open Access Journals (Sweden)

Maddi N. V. D. Harikiran

2017-03-01

Full Text Available Azilsartan Kamedoxomil is an AT1-subtype angiotensin II receptor blocker (ARB. During the laboratory synthesis of Azilsartan Kamedoxomil, four related substances of Azilsartan Kamedoxomil were observed and identified. These were 2-Ethoxy-3-[[4-[2- [4-[(5-methyl-2-oxo-1,3-dioxol-4-ylmethyl]-5-oxo-1,2,4-oxadiazol-3-yl]phenyl]phenyl] methyl] benzimidazole-4-carboxylic acid (azilsartan N-medoxomil, 9, (5-methyl-2-oxo- 1,3-dioxol-4-ylmethyl 2-ethoxy-3-[[4-[2-[4-[(5-methyl-2-oxo-1,3-dioxol-4-ylmethyl]-5- oxo-1,2,4-oxadiazol-3-yl]phenyl]phenyl] methyl] benzimidazole-4-carboxylate (azilsartan dimedoxomil, 10, (5-methyl-2-oxo-1,3-dioxo-4-ylmethyl 1-[2’-(4,5-dihydro-5-oxo-4H- 1,2,4-oxadiazol-3-ylbiphenyl-4-yl]methyl]-2-methoxy-1H-benzimidazole-7-carboxylate (methoxy analogue of azilsartan medoxomil, 11, Methyl 1-((2’-amidobiphenyl-4-yl methyl-2-ethoxy-1H-benzo[d]imidazole-7-carboxylate (amide methyl ester, 12. The present work describes the origin, synthesis and characterization of these related substances.

Green Synthesis and Characterizations of Flower Shaped CuO Nanoparticles for Biodiesel Application

Directory of Open Access Journals (Sweden)

Rintu Varghese

2017-03-01

Full Text Available Nanomaterials are primary candidates to play a key role in energy future. In this work, plant-mediated green synthesis of CuO nanoparticles was studied. The CuO nanoparticles were used as the catalysts for the production of biodiesel from coconut oil. An aqueous extract of Centella Asiatica leaves was used as a bio-reducing agent for the synthesis of CuO nanoparticles. This biocatalyst was characterized by using different techniques (FTIR, UV-Vis spectroscopy, XRD, FESEM with EDX which were confirmed the formation of CuO nanoparticles. Further, the presences of FAME (Fatty Acid Methyl Ester groups at the produced biodiesel were confirmed using both the GC-MS and FTIR analysis. From this work, it has been concluded that the plant extract mediated synthesis of CuO nanoparticles is quite simple, cost-effective and environmentally friendly. The produced biodiesel from coconut oil is considered to be a potential source for alternative conventional fuel.

Synthesis and characterization of "1"3C_3-tristearin

International Nuclear Information System (INIS)

Wu Hangyu; Lin Lin; Li Lei; Chen Dazhou

2011-01-01

A highly efficient synthesis of "1"3C_3 labeled triglycerides of stearic acids from "1"3C_3-glycerol and stearic acids, by immobilized lipase-catalyzed in solvent-free medium was described. The structure of the product were characterized by fourier transform infrared spectrum (FT-IR), nuclear magnetic resonance (NMR), mass spectra (MS). The results showed that triglycerides of stearic acids contained three "1"3C atoms. The isotope abundance of "1"3C_3-tristearin was more than 99% and the yield was 80% of "1"3C_3-tristearin through calculation. Chemical purity (> 98%) was obtained by differential scanning calorimetry (DSC). (authors)

A facile soft template synthesis and characterization of PbHAsO4 nanocrystals

International Nuclear Information System (INIS)

Xiu Zhiliang; Lue Mengkai; Zhou Guangjun; Gu Feng; Zhang Haiping; Xu Dong; Yuan Duorong

2004-01-01

Monoclinic lead hydrogen arsenate (LHA) nanocrystals with different crystallization morphologies and crystallite sizes were prepared successfully by a soft template synthesis method in the presence of sodium dodecylbenzenesulfonate (SDBS) or polyvinylpyrrolidone (PVP). The products were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The possible mechanism of SDBS and PVP in the experiment was briefly illustrated

Control of DNA synthesis in inhibited and activated Agrostemma githago seeds

Energy Technology Data Exchange (ETDEWEB)

Hecker, M [Sektion Biologie, FG Algemeine Botanik und Pflanzenphysiologie, Universitaet Greifswald (German Democratic Republic)

1975-01-01

The relationships between DNA synthesis and germination capacity of Agrostemma seeds had been studied. Protein synthesis and RNA synthesis were activated at the very beginning of imbibition, whereas DNA synthesis started in the second part of the imbibition phase. Agrostemma seeds inhibited by higher temperature (30 degC), or aged seeds with a low germination capacity were characterized by a significantly reduced protein synthesis. DNA synthesis was also reduced. The inhibition of the protein synthesis of Agrostemma embryos fed with cycloheximide or actinomycin D caused a depression of DNA synthesis. The results indicated that the initiation of DNA synthesis of imbibing Agrostemma seeds depended on the synthesis of special proteins. Abscisic acid inhibited the growth as well as DNA synthesis of isolated Agrostemma embryos. Nitomycin inhibited germination and DNA synthesis to the same extent. Dormant seeds with an undiminished intensity of protein synthesis also showed a reduced incorporation of /sup 3/H-thymidine by DNA. It is suggested that DNA synthesis of imbibed seeds, which is a necessary prerequisite for the radicle protrusion, was involved in the mechanism of ripening of the Agrostemma seeds.

Control of DNA synthesis in inhibited and activated Agrostemma githago seeds

International Nuclear Information System (INIS)

Hecker, M.

1975-01-01

The relationships between DNA synthesis and germination capacity of Agrostemma seeds had been studied. Protein synthesis and RNA synthesis were activated at the very beginning of imbibition, whereas DNA synthesis started in the second part of the imbibition phase. Agrostemma seeds inhibited by higher temperature (30 degC), or aged seeds with a low germination capacity were characterized by a significantly reduced protein synthesis. DNA synthesis was also reduced. The inhibition of the protein synthesis of Agrostemma embryos fed with cycloheximide or actinomycin D caused a depression of DNA synthesis. The results indicated that the initiation of DNA synthesis of imbibing Agrostemma seeds depended on the synthesis of special proteins. Abscisic acid inhibited the growth as well as DNA synthesis of isolated Agrostemma embryos. Nitomycin inhibited germination and DNA synthesis to the same extent. Dormant seeds with an undiminished intensity of protein synthesis also showed a reduced incorporation of 3 H-thymidine by DNA. It is suggested that DNA synthesis of imbibed seeds, which is a necessary prerequisite for the radicle protrusion, was involved in the mechanism of ripening of the Agrostemma seeds. (author)

Synthesis and Characterization of Hydroxyapatite/Fullerenol Nanocomposites.

Science.gov (United States)

Djordjevic, Aleksandar; Ignjatovic, Nenad; Seke, Mariana; Jovic, Danica; Uskokovic, Dragan; Rakocevic, Zlatko

2015-02-01

Fullerenols are polyhydroxylated, water soluble derivatives of fullerene C60, with potential application in medicine as diagnostic agents, antioxidants or nano drug carriers. This paper describes synthesis and physical characterization of a new nanocomposite hydroxyapatite/fullerenol. Surface of the nanocomposite hydroxyapatite/fullerenol is inhomogeneous with the diameter of the particles in the range from 100 nm to 350 nm. The ζ potential of this nanocomposite is ten times lower when compared to hydroxyapatite. Surface phosphate groups of hydroxyapatite are prone to forming hydrogen bonds, when in close contact with hydroxyl groups, which could lead to formation of hydrogen bonds between hydroxyapatite and hydroxyl groups of fullerenol. The surface of hydroxyapatite particles (-2.5 mV) was modified by fullerenol particles, as confirmed by the obtained ζ potential value of the nanocomposite biomaterial hydroxyapatite/fullerenol (-25.0 mV). Keywords: Hydroxyapatite, Fullerenol, Nanocomposite, Surface Analysis.

Amino acids augment muscle protein synthesis in neonatal pigs during acute endotoxemia by stimulating mTOR-dependent translation initiation.

Science.gov (United States)

Orellana, Renán A; Jeyapalan, Asumthia; Escobar, Jeffery; Frank, Jason W; Nguyen, Hanh V; Suryawan, Agus; Davis, Teresa A

2007-11-01

In skeletal muscle of adults, sepsis reduces protein synthesis by depressing translation initiation and induces resistance to branched-chain amino acid stimulation. Normal neonates maintain a high basal muscle protein synthesis rate that is sensitive to amino acid stimulation. In the present study, we determined the effect of amino acids on protein synthesis in skeletal muscle and other tissues in septic neonates. Overnight-fasted neonatal pigs were infused with endotoxin (LPS, 0 and 10 microg.kg(-1).h(-1)), whereas glucose and insulin were maintained at fasting levels; amino acids were clamped at fasting or fed levels. In the presence of fasting insulin and amino acids, LPS reduced protein synthesis in longissimus dorsi (LD) and gastrocnemius muscles and increased protein synthesis in the diaphragm, but had no effect in masseter and heart muscles. Increasing amino acids to fed levels accelerated muscle protein synthesis in LD, gastrocnemius, masseter, and diaphragm. LPS stimulated protein synthesis in liver, lung, spleen, pancreas, and kidney in fasted animals. Raising amino acids to fed levels increased protein synthesis in liver of controls, but not LPS-treated animals. The increase in muscle protein synthesis in response to amino acids was associated with increased mTOR, 4E-BP1, and S6K1 phosphorylation and eIF4G-eIF4E association in control and LPS-infused animals. These findings suggest that amino acids stimulate skeletal muscle protein synthesis during acute endotoxemia via mTOR-dependent ribosomal assembly despite reduced basal protein synthesis rates in neonatal pigs. However, provision of amino acids does not further enhance the LPS-induced increase in liver protein synthesis.

Synthesis, Characterization and Applications of One-Dimensional Metal Oxide Nanostructures

Science.gov (United States)

Santulli, Alexander

Nanomaterials have been of keen research interest, owing to their exciting and unique properties (e.g. optical, magnetic, electronic, and mechanical). These properties allow nanomaterials to have many applications in areas of medicine, alternative energy, catalysis, and information storage. In particular, one-dimensional (1D) nanomaterials are highly advantageous, owing to the inherent anisotropic nature, which allows for effective transport and study of properties on the nanoscale. More specifically, 1D metal oxide nanomaterials are of particular interest, owing to their high thermal and chemical stability, as well as their intriguing optical, electronic, and magnetic properties. Herein, we will investigate the synthesis and characterization of vanadium oxide, lithium niobate and chromium oxide. We will explore the methodologies utilized for the synthesis of these materials, as well as the overall properties of these unique nanomaterials. Furthermore, we will explore the application of titanium dioxide nanomaterials as the electron transport layer in dye sensitized solar cells (DSSCs), with an emphasis on the effect of the nanoscale morphology on the overall device efficiency.

β-galactosidase-catalyzed synthesis of galactosyl chlorphenesin and its characterization.

Science.gov (United States)

Lee, Sang-Eun; Jo, Tae-Min; Lee, Hyang-Yeol; Lee, Jongsung; Jung, Kyung-Hwan

2013-11-01

We synthesized galactosyl chlorphenesin (CPN-G) using β-gal-containing Escherichia coli (E. coli) cells in which the conversion yield of chlorphenesin (CPN) to CPN-G reached about 64 % during 12 h. CPN-G was identified and characterized using high-performance liquid chromatography, liquid chromatography-mass spectrometry, Fourier transform-infrared spectrometry, and nuclear magnetic resonance analysis ((1)H and (13)C). We verified that a galactose was covalently bound to a CPN alcohol group during CPN-G synthesis throughout these analyses. In particular, by the hydrolysis of CPN-G using β-gal, it was confirmed that a galactose was bound to CPN. The minimal inhibitory concentration (MIC) results showed that the CPN-G MICs were fairly similar to those of CPN. HACAT cell viability was significantly higher in CPN-G-treated cells than in CPN-treated cells at concentrations of 0.0-20.0 mM. Finally, we accomplished the synthesis of less toxic CPN-G, compared with CPN, using β-gal-containing E. coli cells as whole cells without changes in the MICs against microorganisms.

Polyhomologation based on in situ generated Boron-thexyl-silaboracyclic initiating sites: a novel strategy towards the synthesis of polyethylene-based complex architectures

KAUST Repository

Zhang, Zhen

2015-04-10

A novel strategy, based on the in situ generated Boron-thexyl-silaboracyclic initiating sites for the polyhomologation of dimethylsulfoxonium methylide, has been developed for the synthesis of complex polyethylene-based architectures. As examples, the synthesis of a 4-arm polyethylene star, three (polystyrene)(polyethylene)2 3-miktoarm stars and a PE-branched double graft copolymers are given.

SYNTHESIS, CHARACTERIZATION AND ANTIBACTERIAL ...

African Journals Online (AJOL)

Preferred Customer

In the present study, synthesis, and biological evaluation of some novel ... Then slowly cooled and resultant mixture was basified with aqueous sodium hydroxide ... mol), anhydrous potassium carbonate (5.52 g, 0.04 mol) in acetone (25 mL), ...

Synthesis, purification and physico-chemical characterization of the deuterized chloroform

International Nuclear Information System (INIS)

Mihaila, V.; Olteanu-Chiper, D.

1999-01-01

This work refers to deuterized chloroform synthesis and purification methods. Three methods for obtaining deuterized chloroform are presented. 1. The direct chlorination of methane, in presence of light and in oxygen-free atmosphere: CH 4 + 3 Cl 2 + ℎν→ CHCl 3 + 3 HCl. The method's drawback is that the product obtained is impure, as other chlorinated compounds such as CH 3 Cl, CH 2 Cl 2 , CCl 4 also result. 2. Chlorination of acetaldehyde or acetone, in basic catalysis and in halogen excess (α substitution with direct synthesis of trihalogen compound), followed by a haloform reaction (hydrolytic splitting) in presence of chlorinated lime: CH 3 CHO (Cl 2 /HO - )/(-HCl)Cl 3 C-CHO (CaCl 2 /HOH)/(-(HCOO) 2 Ca) CHCl 3 and CH 3 -CO-CH 3 (Cl 2 /HO)/(-HCl) Cl 3 C-CO-CH 3 (NaOH)/(-CH 3 COONa) CHCl 3 . 3. Decarboxylizing of trichloroacetate acid (as sodium salt): Cl 3 C-COONa (t deg C)/(H 2 O) Cl 3 CH + NaHCO 3 . This method is the most suitable for the deuterized chloroform synthesis since the reaction takes place in absence of other hydrogen atoms (protons) and in deuterized water 99,87% purity, according to the following reaction: Cl 3 C-COONa (t deg C)/(D 2 O) Cl 3 CD + NaDCO 3 . Another advantage is that this method avoids the synthesis of secondary products which could entail additional purifications (distillations, rectifications, a.s.o.). The deuterized chloroform is separated from the deuterized sodium bicarbonate aqueous solution by washing with deuterized water, in a liquid-to-liquid separating funnel. After separation, the deuterized chloroform is dried in nitrogen atmosphere. The characterization of the final product is carried out through Nuclear Magnetic Resonance Spectrometry. (authors)

Synthesis of α-Bromine- Terminated Polystyrene Macroinitiator and Its Initiation of MMA Polymerization by ATRP

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

In the present paper the synthesis of block copolymers via the transformation from living anionic polymerization (LAP) to atom transfer radical polymerization (ATRP) was described. Α-Bromine-terminated polystyrenes(PStBr) in the LAP step was prepared by using n-BuLi as initiator, tetrahydrofuran (THF) as the activator, α-methylstyrene (α-MeSt) as the capping group and liquid bromine (Br2) as the bromating agent. The effects of reaction conditions such as the amounts of α-MeSt, THF, and Br2 as well as molecular weight of polystyrene on the bromating efficiency (BE) and coupling extent (CE) were examined. The present results show that the yield of PStBr obtained was more than 93.8% and the coupling reaction was substantially absent. PStBr was further used as the macroinitiator in the polymerization of methyl-methacrylate(MMA) in the presence of copper(Ⅰ) halogen and 2,2-bipyridine(bpy) complexes. It was found that the molecular weight of the resulted PSt-b-PMMA increased linearly with the increase of the conversion of MMA and the polydispersity was 1.2-1.6. The structures of PStBr and P(St-b-MMA) were characterized by 1H NMR spectra.

Production of nanocrystalline metal powders via combustion reaction synthesis

Science.gov (United States)

Frye, John G.; Weil, Kenneth Scott; Lavender, Curt A.; Kim, Jin Yong

2017-10-31

Nanocrystalline metal powders comprising tungsten, molybdenum, rhenium and/or niobium can be synthesized using a combustion reaction. Methods for synthesizing the nanocrystalline metal powders are characterized by forming a combustion synthesis solution by dissolving in water an oxidizer, a fuel, and a base-soluble, ammonium precursor of tungsten, molybdenum, rhenium, or niobium in amounts that yield a stoichiometric burn when combusted. The combustion synthesis solution is then heated to a temperature sufficient to substantially remove water and to initiate a self-sustaining combustion reaction. The resulting powder can be subsequently reduced to metal form by heating in a reducing gas environment.

Targeting tumor-initiating cells: Eliminating anabolic cancer stem cells with inhibitors of protein synthesis or by mimicking caloric restriction

Science.gov (United States)

Lamb, Rebecca; Harrison, Hannah; Smith, Duncan L.; Townsend, Paul A.; Jackson, Thomas; Ozsvari, Bela; Martinez-Outschoorn, Ubaldo E.; Pestell, Richard G.; Howell, Anthony; Lisanti, Michael P.; Sotgia, Federica

2015-01-01

We have used an unbiased proteomic profiling strategy to identify new potential therapeutic targets in tumor-initiating cells (TICs), a.k.a., cancer stem cells (CSCs). Towards this end, the proteomes of mammospheres from two breast cancer cell lines were directly compared to attached monolayer cells. This allowed us to identify proteins that were highly over-expressed in CSCs and/or progenitor cells. We focused on ribosomal proteins and protein folding chaperones, since they were markedly over-expressed in mammospheres. Overall, we identified >80 molecules specifically associated with protein synthesis that were commonly upregulated in mammospheres. Most of these proteins were also transcriptionally upregulated in human breast cancer cells in vivo, providing evidence for their potential clinical relevance. As such, increased mRNA translation could provide a novel mechanism for enhancing the proliferative clonal expansion of TICs. The proteomic findings were functionally validated using known inhibitors of protein synthesis, via three independent approaches. For example, puromycin (which mimics the structure of tRNAs and competitively inhibits protein synthesis) preferentially targeted CSCs in both mammospheres and monolayer cultures, and was ~10-fold more potent for eradicating TICs, than “bulk” cancer cells. In addition, rapamycin, which inhibits mTOR and hence protein synthesis, was very effective at reducing mammosphere formation, at nanomolar concentrations. Finally, mammosphere formation was also markedly inhibited by methionine restriction, which mimics the positive effects of caloric restriction in cultured cells. Remarkably, mammosphere formation was >18-fold more sensitive to methionine restriction and replacement, as directly compared to monolayer cell proliferation. Methionine is absolutely required for protein synthesis, since every protein sequence starts with a methionine residue. Thus, the proliferation and survival of CSCs is very sensitive to

Synthesis and characterization of homogeneous interstitial solutions of nitrogen and carbon in iron-based lattices

DEFF Research Database (Denmark)

Brink, Bastian Klüge

work in synthesis and characterization of interstitial solutions ofnitrogen and carbon in iron-based lattices. In order to avoid the influences of gradients incomposition and residual stresses, which are typically found in treated surface layers,homogenous samples are needed. These were prepared from...

Advances in acrylic-alkyd hybrid synthesis and characterization

Science.gov (United States)

Dziczkowski, Jamie

2008-10-01

performance. Reversible-addition fragmentation polymerization techniques were employed to create a new class of acrylic-alkyd hybrid materials. Medium and long oil alkyds made from the monoglyceride process using soybean oil, glycerol, and phthalic anhydride were modified with a RAFT chain transfer agent. The alkyd macro-RAFT agents were reached by end-capping a medium oil soya-based alkyd with a carboxy-functional trithiocarbonate. The alkyd macro-RAFT agents were then used to create acrylic-alkyd block structures by polymerizing different acrylic monomers, including both acrylates and methacrylates in the presence of the macro-RAFT agent and 2, 2'-azobisisobutyronitrile (AIBN). Co-acrylic segments were reached by complete polymerization of one monomer followed by the addition of a second monomer and additional free radical initiator. The alkyds, macro-RAFT agents and, acrylic-alkyd blocks were characterized by size-exclusion chromatography (SEC), FTIR, and 1H-NMR. Pseudo-first-order kinetics behavior and conversion vs. molecular weight plots show that the RAFT-mediated reaction afforded a more controlled process for the synthesis of acrylated-alkyd materials. Preliminary coatings tests showed that material properties of acrylated-alkyds achieved by RAFT polymerization exhibit good overall coatings properties including adhesion, gloss, hardness, and impact resistance.

Self-sustained high-temperature reactions : Initiation, propagation and synthesis

NARCIS (Netherlands)

Martinez Pacheco, M.

2007-01-01

Self-Propagating High-Temperature Synthesis (SHS), also called combustion synthesis is an exothermic and self-sustained reaction between the constituents, which has assumed significance for the production of ceramics and ceramic-metallic materials (cermets), because it is a very rapid processing

Refined Synthesis and Characterization of Controlled Diameter, Narrow Size Distribution Microparticles for Aerospace Research Applications

Science.gov (United States)

Tiemsin, Pacita I.; Wohl, Christopher J.

2012-01-01

Flow visualization using polystyrene microspheres (PSL)s has enabled researchers to learn a tremendous amount of information via particle based diagnostic techniques. To better accommodate wind tunnel researchers needs, PSL synthesis via dispersion polymerization has been carried out at NASA Langley Research Center since the late 1980s. When utilizing seed material for flow visualization, size and size distribution are of paramount importance. Therefore, the work described here focused on further refinement of PSL synthesis and characterization. Through controlled variation of synthetic conditions (chemical concentrations, solution stirring speed, temperature, etc.) a robust, controllable procedure was developed. The relationship between particle size and salt concentration, MgSO4, was identified enabling the determination of PSL diameters a priori. Suggestions of future topics related to PSL synthesis, stability, and size variation are also described.

Synthesis and characterization of Al-TON zeolite using a dialkylimizadolium as structure-directing agent

Energy Technology Data Exchange (ETDEWEB)

Lopes, Christian Wittee; Pergher, Sibele Berenice Castella, E-mail: chriswittee@gmail.com [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Villarroel-Rocha, Jhonny [Laboratorio de Solidos Porosos, Instituto de Fisica Aplicada, Universidad Nacional de San Luis, Chacabuco, San Luis (Argentina); Silva, Bernardo Araldi Da; Mignoni, Marcelo Luis [Universidade Regional Integrada, Erechim, RS (Brazil)

2016-11-15

In this work, the synthesis of zeolites using 1-butyl-3-methylimidazolium chloride [C{sub 4}MI]Cl as a structure-directing agent was investigated. The organic cation shows effectiveness and selectivity for the syntheses of TON zeolites under different reaction conditions compared to the traditional structure directing agent, 1,8-diaminooctane. The 1-butyl-3-methylimidazolium cation lead to highly crystalline materials and its role as OSDA in our synthesis conditions has been confirmed by characterization techniques. ICP-OES confirms the presence of Al in the samples and {sup 27}Al MAS NMR analysis indicated that aluminum atoms were incorporated in tetrahedral coordination. Scanning electron microscopy indicated that changing the crystallization condition (static or stirring), zeolites with different crystal size were obtained, which consequently affects the textural properties of the zeolites. Moreover, varying some synthesis parameters MFI zeolite can also be obtained. (author)

Antibacterial gold nanoparticles-biomass assisted synthesis and characterization.

Science.gov (United States)

Badwaik, Vivek D; Willis, Chad B; Pender, Dillon S; Paripelly, Rammohan; Shah, Monic; Kherde, Yogesh A; Vangala, Lakshmisri M; Gonzalez, Matthew S; Dakshinamurthy, Rajalingam

2013-10-01

Xylose is a natural monosaccharide found in biomass such as straw, pecan shells, cottonseed hulls, and corncobs. Using this monosaccharide, we report the facile, green synthesis and characterization of stable xylose encapsulated gold nanoparticles (Xyl-GNPs) with potent antibacterial activity. Xyl-GNPs were synthesized using the reduction property of xylose in an aqueous solution containing choloraurate anions carried out at room temperature and atmospheric pressure. These nanoparticles were stable and near spherical in shape with an average diameter of 15 +/- 5 nm. Microbiological assay results showed the concentration dependent antibacterial activity of these particles against both Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus epidermidis) bacteria. Thus the facile, environmentally friendly Xyl-GNPs have many potential applications in chemical and biomedical industries, particularly in the development of antibacterial agents in the field of biomedicine.

Synthesis and characterization of waterborne polyurethane acrylate copolymers

International Nuclear Information System (INIS)

Sultan, Misbah; Bhatti, Haq Nawaz; Zuber, Mohammad; Barikani, Mehdi

2013-01-01

Polyurethane acrylate copolymers were synthesized by emulsion polymerization process. To reduce the environmental hazards, organic solvents were replaced by eco-friendly aqueous system. Concentration of polyurethane and acrylate monomer was varied to investigate the effect of chemical composition on performance properties of copolymers. FTIR spectroscopy was used as a key tool to record the chemical synthesis route. The synthesized copolymer emulsions were characterized by evaluating their particle size, viscosity, dry weight content, chemical and water resistance. Thermal decomposition was studied by thermogravimetric analysis. Scanning electron microscope was used to visualize the morphological structure of copolymers. The experimental results indicate better polyurethane acrylate compatibility till the ratio of 30/70. However, these copolymers exhibited synergistic effects between the two polymers and revealed a remarkable improvement in numerous coating properties

Synthesis, characterization and behaviour to gamma radiation of the bis-L-alaninato-copper (II)

International Nuclear Information System (INIS)

Passos, B.F.T.

1985-01-01

The behaviour of coordinated compound obtained from the copper (II) and the L-(+)- alanine to gamma radiation was determined. A study of synthesis and characterization of this complex was made with elementary analysis, ultraviolet and visible electronic spectroscopy, infrared vibrational spectroscopy, proton magnetic resonance spectroscopy and thermo-gravimetric analysis. (C.G.C.)

Synthesis and characterization of low-valence actinide phosphide tellurides and ternary selenium-halide iridium complexes; Synthese und Charakterisierung niedervalenter Actinoidphosphidtelluride und ternaerer Selen-Halogenid-Komplexe des Iridiums

Energy Technology Data Exchange (ETDEWEB)

Stolze, Karoline

2016-04-07

The thesis on the synthesis and characterization of low-valence actinide phosphide tellurides and ternary selenium-halide iridium complexes includes two parts: a description of the experimental synthesis of UPTe and U2PTe2O and ThPTe and the synthesis of selenium-chloride iridium complexes and selenium-bromide iridium complexes. The characterization included X-ray diffraction and phase studies.

Synthesis and characterization of carboxylic acid functionalized silicon nanoparticles

Science.gov (United States)

Shaner, Ted V.

Silicon nanoparticles are of great interest in a great number of fields. Silicon nanoparticles show great promise particularly in the field of bioimaging. Carboxylic acid functionalized silicon nanoparticles have the ability to covalently bond to biomolecules through the conjugation of the carboxylic acid to an amine functionalized biomolecule. This thesis explores the synthesis of silicon nanoparticles functionalized by both carboxylic acids and alkenes and their carboxylic acid functionality. Also discussed is the characterization of the silicon nanoparticles by the use of x-ray spectroscopy. Finally, the nature of the Si-H bond that is observed on the surface of the silicon nanoparticles will be investigated using photoassisted exciton mediated hydrosilation reactions. The silicon nanoparticles are synthesized from both carboxylic acids and alkenes. However, the lack of solubility of diacids is a significant barrier to carboxylic acid functionalization by a mixture of monoacids and diacids. A synthesis route to overcome this obstacle is to synthesize silicon nanoparticles with terminal vinyl group. This terminal vinyl group is distal to the surface of the silicon nanoparticle. The conversion of the vinyl group to a carboxylic acid is accomplished by oxidative cleavage using ozonolysis. The carboxylic acid functionalized silicon nanoparticles were then successfully conjugated to amine functionalized DNA strand through an n-hydroxy succinimide ester activation step, which promotes the formation of the amide bond. Conjugation was characterized by TEM and polyacrylamide gel electrophoresis (PAGE). The PAGE results show that the silicon nanoparticle conjugates move slower through the polyacrylamide gel, resulting in a significant separation from the nonconjugated DNA. The silicon nanoparticles were then characterized by the use of x-ray absorption near edge spectroscopy (Xanes) and x-ray photoelectron spectroscopy (XPS) to investigate the bonding and chemical

Synthesis and Characterization of EDTA Complexes Useful for Trace Elements Supplementation

Directory of Open Access Journals (Sweden)

Baran Enrique J.

2002-01-01

Full Text Available The synthesis of two heterobimetallic EDTA complexes, MgCu(EDTA.6H2O and ZnCu(EDTA.6H2O, is described. They were characterized by means of vibrational (infrared and Raman and electronic (reflectance spectroscopy. Several dissolution tests in 0.1 N HCl and simulated gastric juice were also performed. The results support the potential usefulness of these complexes for copper supplementation in human and veterinary medicine and to the simultaneous reinforcement of Mg(II and Zn(II levels.

Chevrel phases superconductive and ultrafine powders synthesis and characterization; Synthese et caracterisation de poudres ultrafines supraconductrices de phases de Chevrel

Energy Technology Data Exchange (ETDEWEB)

Even-Boudjada, S

1994-12-01

This work deals with the Chevrel phases superconductive and ultrafine powders synthesis and characterization. The first part of this study presents some new way of synthesis (precipitation, coprecipitation) of Chevrel phases precursors powders (PbS, SnS, MoS{sub 2}) and their characterizations (X-ray fluorescence analysis, ICP mass spectroscopy, scanning electron microscopy, transmission electron microscopy and laser granulometry). These new synthesis methods lead to quasi spherical morphology grains and very weak size grains (0.2 to 0.5 {mu}m) whereas the chemical preparation from the solid state elements gives very different morphology grains (small plates) with a size of 1 to 20 {mu}m. In the second part is shown the interest of the binary Mo{sub 6} S{sub 8} as precursor in the synthesis of ternary superconductive phases (Li, Ni, Cu, Pb). The last part presents the formation reaction of the phase PbMo{sub 6} S{sub 8} and its main chemical and physical properties. Thus some calorimetric measures associated with X-ray diffraction analysis have been realized and have allowed to understand the different reactions occurring during the PbMo{sub 6}S{sub 8} synthesis. (O.L.). 100 refs., figs., tabs.

On-Surface Synthesis and Characterization of Honeycombene Oligophenylene Macrocycles.

Science.gov (United States)

Chen, Min; Shang, Jian; Wang, Yongfeng; Wu, Kai; Kuttner, Julian; Hilt, Gerhard; Hieringer, Wolfgang; Gottfried, J Michael

2017-01-24

We report the on-surface formation and characterization of [30]-honeycombene, a cyclotriacontaphenylene, which consists of 30 phenyl rings (C 180 H 120 ) and has a diameter of 4.0 nm. This shape-persistent, conjugated, and unsubstituted hexagonal hydrocarbon macrocycle was obtained by solvent-free synthesis on a silver (111) single-crystal surface, making solubility-enhancing alkyl side groups unnecessary. Side products include strained macrocycles with square, pentagonal, and heptagonal shape. The molecules were characterized by scanning tunneling microscopy and density functional theory (DFT) calculations. On the Ag(111) surface, the macrocycles act as molecular quantum corrals and lead to the confinement of surface-state electrons inside the central cavity. The energy of the confined surface state correlates with the size of the macrocycle and is well described by a particle-in-the-box model. Tunneling spectroscopy suggests conjugation within the planar rings and reveals influences of self-assembly on the electronic structure. While the adsorbed molecules appear to be approximately planar, the free molecules have nonplanar conformation, according to DFT.

Design, synthesis, and characterization of 0-D, 1-D, and 2-D Zinc–Adeninate coordination assemblies

Energy Technology Data Exchange (ETDEWEB)

An, Ji Hyun [Dept. of Chemistry Education, Seoul National University, Seoul (Korea, Republic of); Geib, Steven J. [Dept. of Chemistry, University of Pittsburgh, Pittsburgh (United States); Kim, Myung Gil [Dept. of Chemistry, Chungang University, Seoul (Korea, Republic of)

2015-08-15

In this study, we demonstrate the synthesis and characterization of zinc– adeninate coordination polymers with 0-D, 1-D, and 2-D structures. We describe methods for controlling the structure of these materials by applying different synthetic conditions and discuss their structural relationships. 0-D, 1-D, and 2-D zinc–adeninate coordination polymers with the same metal–adeninate coordination mode were synthesized and characterized. By controlling the temperature, a material with 0-D macrocycle or 1-D chain coordination polymer was prepared. A replacement of pyridine with bipyridine formed 2-D sheet structure by connecting 1-D chains with each other. They exhibited an interesting relationship between synthetic methods and structures. Further study of metal–adeninate coordination chemistry will render a precise control of the structure in synthesis and will open a new venue to new materials with fascinating properties.

Graphitic carbon nitride: Synthesis, characterization and photocatalytic decomposition of nitrous oxide

International Nuclear Information System (INIS)

Praus, Petr; Svoboda, Ladislav; Ritz, Michal; Troppová, Ivana; Šihor, Marcel; Kočí, Kamila

2017-01-01

Graphitic carbon nitride (g-C_3N_4) was synthetized by condensation of melamine at the temperatures of 400–700 °C in air for 2 h and resulting products were characterized and finally tested for the photocatalytic decomposition of nitrous oxide. The characterization methods were elemental analysis, UV–Vis diffuse reflectance spectroscopy (DRS), photoluminescence (PL), Fourier transform infrared (FTIR) and Raman spectroscopy, measurement of specific surface area (SSA), X-ray powder diffraction (XRD), scanning (SEM) and transmission (TEM) electron microscopy. The XRD patterns, FTIR and Raman spectra proved the presence of g-C_3N_4 at above 550 °C but the optimal synthesis temperature of 600–650 °C was found. Under these conditions graphitic carbon nitride of the overall empirical composition of C_6N_9H_2 was formed. At lower temperatures g-C_3N_4 with a higher content of hydrogen was formed but at higher temperatures g-C_3N_4 was decomposed. At the temperatures above 650 °C, its exfoliation was observed. The photocatalytic experiments showed that the activity of all the samples synthetized at 400–700 °C was very similar, that is, within the range of experimental error (5 %). The total conversion of N_2O reached about 43 % after 14 h. - Highlights: • Graphitic carbon nitride (g-C_3N_4) was thermally synthetized from melamine in the range of 400–700 °C. • The optimal temperature was determined at 600–650 °C. • All synthesis products were properly characterized by physico-chemical methods. • Exfoliation of g-C_3N_4 at above 600 °C was observed. • g-C_3N_4 was used for the photocatalytic decomposition of N_2O.

Amphiphilic star block copolymers as gene carrier Part I: Synthesis via ATRP using calix[4]resorcinarene-based initiators and characterization

Energy Technology Data Exchange (ETDEWEB)

Zheng, Anna; Xue, Yan; Wei, Dafu [Shanghai Key Laboratory of Advanced Polymeric Materials, Key Laboratory for Ultrafine Materials of Ministry of Education, School of Materials Science and Engineering, East China University of Science and Technology, Shanghai 200237 (China); Guan, Yong, E-mail: yguan@ecust.edu.cn [Shanghai Key Laboratory of Advanced Polymeric Materials, Key Laboratory for Ultrafine Materials of Ministry of Education, School of Materials Science and Engineering, East China University of Science and Technology, Shanghai 200237 (China); Xiao, Huining [Department of Chemical Engineering, University of New Brunswick, Fredericton, New Brunswick, Canada E3B 5A3 (Canada)

2013-01-01

In this work, a cationic star polymer [poly(2-dimethylamino)ethyl methacrylate (PDMAEMA)] was prepared via atom transfer radical polymerization (ATRP), using brominated calix[4]resorcinarene as an initiator. Hydrophobic moieties, methyl methacrylate (MMA) and butyl acrylate (BA), were further incorporated via 'one-pot' method. Well-defined eight-armed star block copolymers bearing hydrophilic blocks inside and hydrophobic blocks outside were synthesized. The molecular weight, particle size, electrophoretic mobility and apparent charge density were determined by gel permeation chromatography (GPC), dynamic light scattering (DLS), phase analysis light scattering (PALS) and colloidal titration, respectively. The zeta potentials and apparent charge densities of the products exhibited the characteristics of polyelectrolyte. The incorporation of hydrophobic moieties generated electrostatic screening effect. The as-synthesized amphiphilic star copolymer is promising as a thermo-sensitive gene carrier for gene therapy. Highlights: Black-Right-Pointing-Pointer Amphiphilic cationic star block copolymers with well-controlled structures were prepared via ATRP. Black-Right-Pointing-Pointer The molecular structures and properties of the initiator and copolymers were systematically characterized. Black-Right-Pointing-Pointer The products exhibited the positive charged character, and hydrophobic moieties generated electrostatic screening effect.

Characterization of PDMS samples with variation of its synthesis parameters for tunable optics applications

Science.gov (United States)

Marquez-Garcia, Josimar; Cruz-Félix, Angel S.; Santiago-Alvarado, Agustin; González-García, Jorge

2017-09-01

Nowadays the elastomer known as polydimethylsiloxane (PDMS, Sylgard 184), due to its physical properties, low cost and easy handle, have become a frequently used material for the elaboration of optical components such as: variable focal length liquid lenses, optical waveguides, solid elastic lenses, etc. In recent years, we have been working in the characterization of this material for applications in visual sciences; in this work, we describe the elaboration of PDMSmade samples, also, we present physical and optical properties of the samples by varying its synthesis parameters such as base: curing agent ratio, and both, curing time and temperature. In the case of mechanical properties, tensile and compression tests were carried out through a universal testing machine to obtain the respective stress-strain curves, and to obtain information regarding its optical properties, UV-vis spectroscopy is applied to the samples to obtain transmittance and absorbance curves. Index of refraction variation was obtained through an Abbe refractometer. Results from the characterization will determine the proper synthesis parameters for the elaboration of tunable refractive surfaces for potential applications in robotics.

Synthesis and characterization of reactions by nanoferrites Co2Fe2O4 combustion

International Nuclear Information System (INIS)

Santos, P.T.A.; Dantas, B.B.; Costa, A.C.F.M.; Araujo, P.M.A.G.

2012-01-01

In this work CoFe 2 O 4 of magnetic nanoparticles were synthesized by combustion reaction and the structural and morphological characteristics of the synthesized samples as well as the parameters of synthesis temperature and reaction time were investigated in order to assess the reproducibility of the synthesis. The maximum temperature and time of the combustion flame were obtained with pyrometer coupled to a computer with online measurement and a stopwatch. The resulting samples were characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The maximum temperature achieved during synthesis for all reactions ranged from 623 deg C and 755 deg C. The combustion flame time varied between 18 and 23 seconds. The XRD showed the formation of only CoFe 2 O 4 inverse spinel phase, with crystallite size 28 nm and crystallinity 78%, with typical morphology of the formation of agglomerates of uniform size, brittle and comprising nanoparticles together by weak forces. (author)

Synthesis and Characterization of Stimuli Responsive Block Copolymers, Self-Assembly Behavior and Applications

Energy Technology Data Exchange (ETDEWEB)

Determan, Michael Duane [Iowa State Univ., Ames, IA (United States)

2005-12-17

The central theme of this thesis work is to develop new block copolymer materials for biomedical applications. While there are many reports of stimuli-responsive amphiphilic [19-21] and crosslinked hydrogel materials [22], the development of an in situ gel forming, pH responsive pentablock copolymer is a novel contribution to the field, Figure 1.1 is a sketch of an ABCBA pentablock copolymer. The A blocks are cationic tertiary amine methacrylates blocked to a central Pluronic F127 triblock copolymer. In addition to the prerequisite synthetic and macromolecular characterization of these new materials, the self-assembled supramolecular structures formed by the pentablock were experimentally evaluated. This synthesis and characterization process serves to elucidate the important structure property relationships of these novel materials, The pH and temperature responsive behavior of the pentablock copolymer were explored especially with consideration towards injectable drug delivery applications. Future synthesis work will focus on enhancing and tuning the cell specific targeting of DNA/pentablock copolymer polyplexes. The specific goals of this research are: (1) Develop a synthetic route for gel forming pentablock block copolymers with pH and temperature sensitive properties. Synthesis of these novel copolymers is accomplished with ATRP, yielding low polydispersity and control of the block copolymer architecture. Well defined macromolecular characteristics are required to tailor the phase behavior of these materials. (2) Characterize relationship between the size and shape of pentablock copolymer micelles and gel structure and the pH and temperature of the copolymer solutions with SAXS, SANS and CryoTEM. (3) Evaluate the temperature and pH induced phase separation and macroscopic self-assembly phenomenon of the pentablock copolymer. (4) Utilize the knowledge gained from first three goals to design and formulate drug delivery formulations based on the multi

Synthesis and characterization of nanostructured powders of hydroxyapatite and β-calcium phosphate

Energy Technology Data Exchange (ETDEWEB)

Prants, W.T.; Muller, D.T.; Orzechowski, L.G.; Feit, G.; Delima, S.A.; Camargo, N.H.A.; Gemelli, E., E-mail: w_prants@hotmail.com, E-mail: danielt_muller@yahoo.com.br, E-mail: sarahamindelima@hotmail.com, E-mail: dem2nhac@joinville.udesc.br, E-mail: gemelli@joinville.udesc.br [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Campus Universitario Prof. Avelino Marcante

2009-07-01

Biphasic calcium phosphate (BCP) bioceramics are composed in a general manner from a mixture between hydroxyapatite (HA), and β-calcium phosphate. In the recent years, the BCP bioceramics are pointed out in researches from regeneration and reconstitution in osseous tissue, in reason of their similar mineralogical characteristics of the human bone structure, as great biodegradation, absorption and formation of precocious osseous tissue. The biphasic materials (BCP) are detached for use in medical and dental application, as filling bone cavities, maxillofacial treatment, medicaments discharge for treatment cancerous osteomyelitis and antibiotics discharge related with orthopedic injuries reparation. The aim of this work focused in synthesis and characterization of hydroxyapatite and β-calcium phosphate. The presented results are related with the mineralogical characterization with X-ray diffraction, thermal behavior with Differential Scanning Calorimetry and Dilatometer. The Scanning Electronic Microscopy (SEM) was used to help in the morphological characterization of the nanostructured powders. (author)

Synthesis and characterization of nanostructured powders of hydroxyapatite and β-calcium phosphate

International Nuclear Information System (INIS)

Prants, W.T.; Muller, D.T.; Orzechowski, L.G.; Feit, G.; Delima, S.A.; Camargo, N.H.A.; Gemelli, E.

2009-01-01

Biphasic calcium phosphate (BCP) bioceramics are composed in a general manner from a mixture between hydroxyapatite (HA), and β-calcium phosphate. In the recent years, the BCP bioceramics are pointed out in researches from regeneration and reconstitution in osseous tissue, in reason of their similar mineralogical characteristics of the human bone structure, as great biodegradation, absorption and formation of precocious osseous tissue. The biphasic materials (BCP) are detached for use in medical and dental application, as filling bone cavities, maxillofacial treatment, medicaments discharge for treatment cancerous osteomyelitis and antibiotics discharge related with orthopedic injuries reparation. The aim of this work focused in synthesis and characterization of hydroxyapatite and β-calcium phosphate. The presented results are related with the mineralogical characterization with X-ray diffraction, thermal behavior with Differential Scanning Calorimetry and Dilatometer. The Scanning Electronic Microscopy (SEM) was used to help in the morphological characterization of the nanostructured powders. (author)

Polypyrrole-silver Nanocomposite: Synthesis and Characterization

Directory of Open Access Journals (Sweden)

D. M. Nerkar

2016-07-01

Full Text Available Polypyrrole-Silver (PPy-Ag nanocomposite has been successfully synthesized by the chemical oxidative polymerization of pyrrole with iron (III chloride as an oxidant, in the presence of a colloidal suspension of silver nanoparticles. Turkevich method (Citrate reduction method was used for the synthesis of silver nanoparticles (Ag NPs. The silver nanoparticles were characterized by UV-Visible spectroscopy which showed an absorption band at 423 nm confirming the formation of nanoparticles. PPy-Ag nanocomposite was characterized by Transmission Electron Microscopy (TEM, Scanning Electron Microscopy (SEM, Fourier Transform Infrared Spectroscopy (FTIR and X-ray diffraction (XRD techniques for morphological and structural confirmations. TEM and SEM images revealed that the silver nanoparticles were well dispersed in the PPy matrix. XRD pattern showed that PPy is amorphous but the presence of the peaks at 2q values of 38.24°, 44.57°, 64.51° and 78.45° corresponding to a cubic phase of silver, revealed the incorporation of silver nanoparticles in the PPy matrix. A possible formation mechanism of PPy-Ag nanocomposite was also proposed. The electrical conductivity of PPy-Ag nanocomposite was studied using two probe method. The electrical conductivity of the PPy-Ag nanocomposite prepared was found to be 4.657´10- 2 S/cm, whereas that of pure PPy was found to be 9.85´10-3 S/cm at room temperature (303 K. The value of activation energy (Ea for pure PPy was 0.045 eV while it decreased to 0.034 eV for PPy-Ag nanocomposite. The synthesized nanocomposite powder can be utilized as a potential material for fabrication of gas sensors operating at room temperature.

Synthesis and characterization of titanium oxide/bismuth sulfide nanorods for solar cells applications

International Nuclear Information System (INIS)

Solis, M.; Rincon, M. E.

2008-01-01

In the present work is showed the synthesis and characterization of titanium oxide/bismuth sulfide nanowires hetero-junctions for solar cells applications. Conductive glass substrates (Corning 25 x 75 mm) were coated with a thin layer of sol-gel TiO2 and used as substrates for the subsequent deposition of bismuth sulfide nanorods (BN). TiO2 films (∼400 nm) were deposited with a semiautomatic immersion system with controlled immersion/withdraw velocity, using titanium isopropoxide as the titania precursor [1]. For BN synthesis and deposition, the solvo-thermal method was used, introducing air annealed TiO2-substrates in the autoclave. The typical bilayer TiO2/BN hetero-junction was 600 nm thick. The synthesized materials (powders and films) were characterized by X-Ray Diffraction, Scanning Electron Microscopy, and UV-Visible Spectroscopy. Anatase was the crystalline phase of TiO2, while bismuth sulfide nanotubes show a diffraction pattern characteristic of bismuthinite distorted by the preferential growth of some planes [2-4]. The optoelectronic characterization of TiO2/NB hetero-junctions was compared with hetero-junctions obtained by sensitizing TiO2 with chemically deposited bismuth sulfide films. Bismuth sulfide nanowires are 2µm long and 70nm wide (aspect ratio L/D = 43), while chemically deposited bismuth sulfide have L/D = 1, therefore the effect of particle size evaluation and geometry in the photosensitization phenomena will be discussed in the context of new materials for solar-cells applications. (Full text)

Synthesis, characterization, and photocatalytic properties of core/shell mesoporous silica nanospheres supporting nanocrystalline titania

International Nuclear Information System (INIS)

Cendrowski, K.; Chen, X.; Zielinska, B.; Kalenczuk, R. J.; Rümmeli, M. H.; Büchner, B.; Klingeler, R.; Borowiak-Palen, E.

2011-01-01

The facile bulk synthesis of silica nanospheres makes them an attractive support for the transport of chemical compounds such as nanocrystalline titanium dioxide. In this contribution we present a promising route for the synthesis of mesoporous silica nanospheres (m-SiO 2 ) with diameter in range 200 nm, which are ideal supports for nanocrystalline titanium dioxide (TiO 2 ). The detailed microscopic and spectroscopic characterizations of core/shell structure (m-SiO 2 /TiO 2 ) were conducted. Moreover, the photocatalytic potential of the nanostructures was investigated via phenol decomposition and hydrogen generation. A clear enhancement of photoactivity in both reactions as compared to commercial TiO 2 -Degussa P25 catalyst is detected.

Synthesis, characterization, and photocatalytic properties of core/shell mesoporous silica nanospheres supporting nanocrystalline titania

Science.gov (United States)

Cendrowski, K.; Chen, X.; Zielinska, B.; Kalenczuk, R. J.; Rümmeli, M. H.; Büchner, B.; Klingeler, R.; Borowiak-Palen, E.

2011-11-01

The facile bulk synthesis of silica nanospheres makes them an attractive support for the transport of chemical compounds such as nanocrystalline titanium dioxide. In this contribution we present a promising route for the synthesis of mesoporous silica nanospheres (m-SiO2) with diameter in range 200 nm, which are ideal supports for nanocrystalline titanium dioxide (TiO2). The detailed microscopic and spectroscopic characterizations of core/shell structure (m-SiO2/TiO2) were conducted. Moreover, the photocatalytic potential of the nanostructures was investigated via phenol decomposition and hydrogen generation. A clear enhancement of photoactivity in both reactions as compared to commercial TiO2-Degussa P25 catalyst is detected.

Synthesis and characterization of rhodium sulfide nanoparticles and thin films

International Nuclear Information System (INIS)

Sosibo, Ndabenhle M.; Revaprasadu, Neerish

2008-01-01

The synthesis and characterization of a rhodium complex, [Rh(S 2 CNEt 2 ) 2 ] is described. The complex was thermolysed at a high temperature (280 deg. C) in the presence of capping agent, hexadecylamine (HDA) to form Rh 2 S 3 nanoparticles. Rod-shaped Rh 2 S 3 nanoparticles with an average length of 26.7 nm and an average breadth of 7.8 nm were synthesized. The complex was also used as a single molecule precursor for the deposition of Rh 2 S 3 thin films on a glass substrate at 350 deg. C and 450 deg. C using the Aerosol Assisted Chemical Vapour Deposition (AACVD) technique. The resultant thin films showed temperature dependent morphologies and showed (0 2 2), (4 1 1) and (6 1 1) lattice planes characteristic of to the orthorhombic Rh 2 S 3 phase. X-ray diffraction and scanning electron microscopy techniques were used to characterize the films

Synthesis and characterization of rhodium sulfide nanoparticles and thin films

Energy Technology Data Exchange (ETDEWEB)

Sosibo, Ndabenhle M. [Department of Chemistry, University of Zululand, Private Bag X1001, KwaDlangezwa 3886 (South Africa); Revaprasadu, Neerish [Department of Chemistry, University of Zululand, Private Bag X1001, KwaDlangezwa 3886 (South Africa)], E-mail: nrevapra@pan.uzulula.za

2008-05-15

The synthesis and characterization of a rhodium complex, [Rh(S{sub 2}CNEt{sub 2}){sub 2}] is described. The complex was thermolysed at a high temperature (280 deg. C) in the presence of capping agent, hexadecylamine (HDA) to form Rh{sub 2}S{sub 3} nanoparticles. Rod-shaped Rh{sub 2}S{sub 3} nanoparticles with an average length of 26.7 nm and an average breadth of 7.8 nm were synthesized. The complex was also used as a single molecule precursor for the deposition of Rh{sub 2}S{sub 3} thin films on a glass substrate at 350 deg. C and 450 deg. C using the Aerosol Assisted Chemical Vapour Deposition (AACVD) technique. The resultant thin films showed temperature dependent morphologies and showed (0 2 2), (4 1 1) and (6 1 1) lattice planes characteristic of to the orthorhombic Rh{sub 2}S{sub 3} phase. X-ray diffraction and scanning electron microscopy techniques were used to characterize the films.

Hyperbranched Polyethylenebased Macromolecular Architectures: Synthesis, Characterization, and Selfassembly

KAUST Repository

Al-Sulami, Ahlam

2018-05-01

polyethylene-b-poly(N-isopropylacrylamide), HBPE-b-PNIPAM, and hyperbranched polyethylene-b-poly(solketal acrylate), HBPE-b-PSA, were successfully synthesized by combining CWCP and ATRP. The synthetic methodology includes the following steps; a) synthesis of multifunction hyperbranched polyethylene initiators HBPE-MI by direct copolymerization of ethylene with 2-(2-bromoisobutyryloxy)ethyl acrylate BIEA in the presence of a α-diimine Pd(II) catalyst, and b) HBPE-MI with α-bromoester groups used as initiation sites for ATRP. Proton nuclear magnetic resonance spectroscopy, 1H NMR, gel permeation chromatography,GPC, and Fourier transform infrared, FT-IR, spectroscopy, were used for determining the molecular and composition structures. Also, differential scanning calorimetry, DSC, and thermogravimetric analysis, TGA, were used to record the melting temperature and to study the thermal stability, respectively. In the fourth part, a well-defined 3-miktoarm star copolymer 3μ-HBPE(PCL)2 (HBPE: hyperbranched polyethylene, PCL: poly(ε-caprolactone) was synthesized by combining CWCP, ring opening polymerization, ROP, and “click” chemistry. The synthetic methodology includes the following steps: a) synthesis of azido-functionalized hyperbranched polyethylene HBPE-N3 by CWCP of ethylene with the α-diimine Pd(II) catalyst, followed by quenching with an excess of 4-vinylbenzyl chloride and transformation of –Cl to the azido group with sodium azide, b) synthesis of in-chain ethynyl-functionalized poly(ε-caprolactone), (PCL)2-C≡CH by ROP of ε-CL with ethynylfunctionalized solketal [3-(prop-2-yn-1-yloxy) propane-1,2-diol] as a bifunctional initiator, in the presence of P2-t-Bu phosphazene super base, and c) “clicking” HBPE-N3 and (PCL)2-C≡CH using the copper(I)-catalyzed alkyne–azide cycloaddition CuAAC. Proton nuclear magnetic resonance spectroscopy, 1H NMR, gel permeation chromatography, GPC, and Fourier transform infrared, FT-IR, spectroscopy, were used to determine

Synthesis, characterization, and reactivity of furan- and thiophene-functionalized bis(n-heterocyclic carbene) complexes of iron(II)

KAUST Repository

Rieb, Julia; Raba, Andreas; Haslinger, Stefan; Kaspar, Manuel; Pö thig, Alexander; Cokoja, Mirza; Basset, Jean-Marie; Kü hn, Fritz

2014-01-01

The synthesis of iron(II) complexes bearing new heteroatom-functionalized methylene-bridged bis(N-heterocyclic carbene) ligands is reported. All complexes are characterized by single-crystal X-ray diffraction (SC-XRD), nuclear magnetic resonance

Synthesis, characterization and properties

Indian Academy of Sciences (India)

Unknown

work, we report herein the synthesis, structural cha- racterization and properties of a chiral Mn(IV) mononuclear ... atmosphere with a platinum disc working electrode, a platinum wire auxiliary electrode and a Ag/AgCl ... SMART APEX CCD area detector system [λ(Mo-. Kα) = 0⋅71073 Å], graphite monochromator, 2400.

Synthesis And Characterization Of Mebrofenin For Hepatobiliary Imaging

International Nuclear Information System (INIS)

Purwoko; Tamat, Swasono R.; Yunita, Fitri; Kristanti, Eti

2003-01-01

Mebrofenin labeled with Technetium-99m is a new radiopharmaceutical having superior and ideal characteristic as a hepatobiliary-imaging agent. The synthesis and characterization of Mebrofenin (3-Bromo-2,4,6-trimethyl acetanilido iminodiacetic acid) as IDA derivative has been carried out involving three steps of reaction i.e. : acetyllization of 2,4,6-Trimethyl aniline to get 2,4,6-trimethyl chloro acetanilide which upon bromination gives the intermediate bromotrimethyl derivative and [mally by nucleophilic substitution this intermediate product with iminodiacetic acid (IDA) gives mebrofenin. The acetylation and bromination reactions were carried out in acetic acid condition while the substitution was carried out by reflux for 5 hours in ethanol and water adjusted at pH 11. The ethanol was then removed under low pressure, and the unreacted compound was removed by filtration. The filtrate was adjusted to pH 2 - 2.5, and the resulting mebrofenin was isolated by filtration and recrystallized 3 times in ethanol. Characterization of the mebrofenin product was performed by observing its melting point (197-l99 o C), ultra violet and infra red spectra as well as mass spectrometric and high performance liquid chromatographic analysis. The results showed that the product was highly pure and the yield was around 20%

Synthesis and characterization of poly aniline/wood and poly aniline/carbon composites

International Nuclear Information System (INIS)

Kanwal, F.; Siddiqi, S.A.; Tasleem, S.

2009-01-01

Conducting polymers have shown many applications in the field of nano science, nano technology and nuclear science. Poly aniline (PAN I) is the most studied conducting polymer due to its environmental stability, easy availability of its raw materials, and simple synthesis. We have synthesized poly aniline and two of its conducting composites i.e., poly aniline-carbon and poly aniline-wood in acidic medium (HCI) using K/sub 2/Cr/sub 2/O/sub 7/ as oxidizing agent. All samples were characterized by FTIR and four-probe d.c. conductivity methods The synthesis was carried out at two different temperatures (0 degree C and -5 degree C) and it was found that the yield and conductivity were maximum at lower temperature (-5 degree C). The poly aniline-carbon composites showed enhanced conductivity whereas poly aniline-wood composites showed reduced conductivity when compared with the conductivity of pure poly aniline. (author)

Synthesis, structure characterization and catalytic activity of nickel tungstate nanoparticles

Science.gov (United States)

Pourmortazavi, Seied Mahdi; Rahimi-Nasrabadi, Mehdi; Khalilian-Shalamzari, Morteza; Zahedi, Mir Mahdi; Hajimirsadeghi, Seiedeh Somayyeh; Omrani, Ismail

2012-12-01

Taguchi robust design was applied to optimize experimental parameters for controllable, simple and fast synthesis of nickel tungstate nanoparticles. NiWO4 nanoparticles were synthesized by precipitation reaction involving addition of nickel ion solution to the tungstate aqueous reagent and then formation of nickel tungstate nucleolus which are insoluble in aqueous media. Effects of various parameters such as nickel and tungstate concentrations, flow rate of reagent addition and reactor temperature on diameter of synthesized nickel tungstate nanoparticles were investigated experimentally by the aid of orthogonal array design. The results for analysis of variance (ANOVA) showed that particle size of nickel tungstate can be effectively tuned by controlling significant variables involving nickel and tungstate concentrations and flow rate; while, temperature of the reactor has a no considerable effect on the size of NiWO4 particles. The ANOVA results proposed the optimum conditions for synthesis of nickel tungstate nanoparticles via this technique. Also, under optimum condition nanoparticles of NiWO4 were prepared and their structure and chemical composition were characterized by means of EDAX, XRD, SEM, FT-IR spectroscopy, UV-vis spectroscopy, and photoluminescence. Finally, catalytic activity of the nanoparticles in a cycloaddition reaction was examined.

Synthesis and characterization of iron nano particles for the arsenic removal in water

International Nuclear Information System (INIS)

Gutierrez M, O. E.

2011-01-01

The synthesis of iron nanoparticles for the removal of metallic ions in polluted waters has been during the last years study topic for different world organizations. This work presents a synthesis method of conditioned coal with iron nanoparticles starting from the use of leaves of pineapple crown, with the purpose of using it in arsenic removal processes in aqueous phase. For the synthesis of this material, the leaves of the pineapple crown were used like supports structure of the iron nanoparticles. First, the pyrolysis appropriate temperature was determined. For the preparation of the support material, this had contact with a ferric nitrate and hexamine solution, because the preparation of the material and the coal synthesis were realized during the pyrolysis process, where the hexamine molecules and the ferric nitrate react, causing the reduction of the iron particles and their dispersion on the support material, obtaining as product a conditioned coal with iron nanoparticles. For the characterization of the materials were used techniques as: Scanning electron microscopy, Transmission electron microscopy, X-Rays Diffraction), X-Ray photoelectron spectroscopy and Moessbauer spectroscopy; moreover was determined the isoelectric point and the density of surface sites. The arsenic sorption capacity of the materials was evaluated by means of the methodology type lots where was determined the sorption kinetics and isotherms in terms of arsenic concentration and mass. (Author)

Synthesis and characterization of the natural and burned hydrotalcite

International Nuclear Information System (INIS)

Granados C, F.

2006-01-01

The synthesis and the structural and surface properties of the natural and burned hydrotalcite using salts of AlCl 3 and MgCl 2 .6H 2 O its were studied. Its were used those analysis of BET, IR, XRD, TGA and SEM to characterize these materials. The obtained product was identified as the natural or carbonated hydrotalcite of chemical formula Mg 6 Al 2 (OH) 16 CO 3 .4H 2 O. The hydrotalcite was roasted at 500 C during 5 h and the was obtained roasted hydrotalcite (HTC) that is a material of high selectivity toward the anions that it can be efficiently used as adsorbent material in studies of adsorption for the treatment of anionic radioactive waste present in watery solution. (Author)

Synthesis and characterization of various zeolites and study of dynamic adsorption of dimethyl methyl phosphate over them

International Nuclear Information System (INIS)

Khanday, Waheed Ahmad; Majid, Sheikh Abdul; Chandra Shekar, S.; Tomar, Radha

2013-01-01

Graphical abstract: Thermal desorption pattern of DMMP over various zeolites (a) 1st desorption and (b) 2nd desorption. - Highlights: • Synthesis of Zeolite-A, MCM-22, Zeolite-X and Erionite by hydrothermal method. • Zeolites were characterized by using XRD, FTIR, BET, NH 3 -TPD, SEM and EDS techniques. • Dynamic adsorption of DMMP on zeolites was carried out using TPD plus chemisorption system. • Thermal desorption of DMMP on zeolites was carried using the same system. - Abstract: Zeolite-A, MCM-22, Zeolite-X and Erionite were synthesized successfully under hydrothermal conditions and were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Brunauer–Emmett–Teller (BET) surface area analysis and thermal programmed desorption (TPD). Dynamic adsorption of dimethyl methyl phosphate (DMMP) was carried out on these zeolites. Zeolite-X having high surface area among all four zeolites shows highest adsorption capacity followed by Erionite and MCM-22 where as Zeolite-A shows the least. For all zeolites adsorption was found to be high initially and it then decreases with increase in injected volume. Then desorption pattern was analyzed which shows two types of peaks, sharp peak representing desorption of physisorbed DMMP and a broad peak representing desorption of strongly chemisorbed DMMP

Synthesis and Characterization Pectin-Carboxymethyl Chitosan crosslinked PEGDE as biosorbent of Pb(II) ion

Science.gov (United States)

Hastuti, Budi; Siswanta, Dwi; Mudasir; Triyono

2018-01-01

Pectin and chitosan are biodegradable polymers, potentially applied as a heavy metal adsorbents. Unfortunately both biosorbents pectin and chitosan have a weakness in acidic media. For this purpose required modified pectin and chitosan. The modified adsorben is intended to obtain a stable adsorbent and resistance under acid. The research was done by experimental method in laboratory. The stages of this research are the synthesis of carboxymethyl chitosan (CMC), synthesis of Pec-CMC-PEGDE film adsorbent, stabily test under acid, the characterization of active group using FTIR, stability characterization of Pec-CMC-PEGDE powder adsorbent using XRD, termo stability using DTA-TGA. The results of the research have shown that: pectin and CMC can be cross-linked using PEGDE crosslinking agent, the film adsorbent was stable under HCl 1 M, the film adsorbent have active group comprise of carboxylate and amine groups. The result of characterization using XRD, shows that the adsorbent is semi-crystalline. Base on termo stability, the film adsorbent Pec-CMC-PEGDE stable up to 600°C. The film can be applied as an adsobent of Pb (II) ion remediation. The optimum pH of pec-CMC-PEGDE in adsorbed of Pb(II) was reached at pH 5 with 99.99% absorbent adsorbed and of and adsorption capacity was 46.11 mg/g.

SYNTHESIS, CHARACTERIZATION AND BIO-ACTIVITY OF SOME ...

African Journals Online (AJOL)

Preferred Customer

Organophosphorus compounds have wide range of applications in the industrial, agricultural and medicinal chemistry owing to their unique physicochemical and biological properties. Their utility as reagents and potential synthons in organic synthesis is gaining increased attention [1]. Synthesis of a-aminophosphonates, ...

Streptomyces somaliensis mediated green synthesis of silver nanoparticles

Directory of Open Access Journals (Sweden)

Meysam Soltani Nejad

2015-07-01

Full Text Available Objective(s: The development of reliable and ecofriendly process for the synthesis of nano-metals is an important aspect in the field of nanotechnology. Nano-metals are a special group of materials with broad area of applications. Materials and Methods: In this study, extracellular synthesis of silver nanoparticles (SNPs performed by use of the gram positive soil Streptomycetes. Streptomycetes isolated from rice fields of Guilan Province, Iran (5 isolates. Initial characterization of SNPs was performed by visual change color. To determine the bacterium taxonomical identity, its colonies characterized morphologically by use of scanning electron microscope. The PCR molecular analysis of active isolate represented its identity partially. In this regard, 16S rDNA of isolate G was amplified using universal bacterial primers FD1 and RP2. The PCR products were purified and sequenced. Sequence analysis of 16S rDNA was then conducted using NCBI GenBank database using BLAST. Also SNPs were characterized by, transmission electron microscopy (TEM and X-ray diffraction spectroscopy (XRD. Results: From all 5 collected Streptomyces somaliensis isolates, isolate G showed highest extracellular synthesis of SNPs via in vitro. SNPs were formed immediately by the addition of (AgNO3 solution (1 mM. UV-visible spectrophotometry for measuring surface plasmon resonance showed a single absorption peak at 450 nm, which confirmed the presence of SNPs. TEM revealed the extracellular formation of spherical silver nanoparticles in the size range of 5-35 nm. Conclusions: The biological approach for the synthesis of metal nanoparticles offers an environmentally benign alternative to the traditional chemical and physical synthesis methods. So, a simple, environmentally friendly and cost-effective method has been developed to synthesize AgNPs using Streptomycetes.

Synthesis and structural characterization of piperazino-modified DNA that favours hybridization towards DNA over RNA

DEFF Research Database (Denmark)

Skov, Joan; Bryld, Torsten; Lindegaard, Dorthe

2011-01-01

We report the synthesis of two C4'-modified DNA analogues and characterize their structural impact on dsDNA duplexes. The 4'-C-piperazinomethyl modification stabilizes dsDNA by up to 5°C per incorporation. Extension of the modification with a butanoyl-linked pyrene increases the dsDNA stabilizati...

Novel synthesis and characterization of an AB-type carbonate-substituted hydroxyapatite.

Science.gov (United States)

Gibson, Iain R; Bonfield, William

2002-03-15

A novel synthesis route has been developed to produce a high-purity mixed AB-type carbonate-substituted hydroxyapatite (CHA) with a carbonate content that is comparable to the type and level observed in bone mineral. This method involves the aqueous precipitation in the presence of carbonate ions in solution of a calcium phosphate apatite with a Ca/P molar ratio greater than the stoichiometric value of 1.67 for hydroxyapatite (HA). The resulting calcium-rich carbonate-apatite is sintered/heat-treated in a carbon dioxide atmosphere to produce a single-phase, crystalline carbonate-substituted hydroxyapatite. In contrast to previous methods for producing B- or AB-type carbonate-substituted hydroxyapatites, no sodium or ammonium ions, which would be present in the reaction mixture from the sodium or ammonium carbonates commonly used as a source of carbonate ions, were present in the final product. The chemical and phase compositions of the carbonate-substituted hydroxyapatite was characterized by X-ray fluorescence and X-ray diffraction, respectively, and the level and nature of the carbonate substitution were studied using C-H-N analysis and Fourier transform infrared spectroscopy, respectively. The carbonate substitution improves the densification of hydroxyapatite and reduces the sintering temperature required to achieve near-full density by approximately 200 degrees C compared to stoichiometric HA. Initial studies have shown that these carbonate-substituted hydroxyapatites have improved mechanical and biologic properties compared to stoichiometric hydroxyapatite. Copyright 2001 John Wiley & Sons, Inc. J Biomed Mater Res 59: 697-708, 2002

Synthesis and Characterization of Pine Needles Reinforced RF Matrix Based Biocomposites

Directory of Open Access Journals (Sweden)

A. S. Singha

2008-01-01

Full Text Available Synthesis and characterization of pine needles reinforced thermosetting resin (Resorcinol-Formaldehyde which is most suitable as composite matrix has been reported. The polycondensation reaction between resorcinol and formaldehyde (RF in different molar ratios has been applied to the synthesis of RF polymer matrix. A thermosetting resin based composite, containing approximately 10, 20, 30 and 40% of natural fiber by weight, has been obtained by adding pine needles to the Resorcinol-Formaldehyde (RF resin. The mechanical properties of randomly oriented intimately mixed particle reinforced (Pine needles composites were determined. Effect of fiber loading in terms of weight % on mechanical properties such as tensile, compressive, and flexural and wear properties have also been evaluated. The reinforcing of the resin with Pine needles was accomplished in particle size of 200 micron by employing optimized resin. Present work reveals that mechanical properties of the RF resin increases to extensive extent when reinforced with Pine needles. Thermal (TGA/DTA and morphological studies (SEM of the resin, fiber and polymer composites thus synthesized have also been carried out.

Copper nanoparticles mediated by chitosan: synthesis and characterization via chemical methods.

Science.gov (United States)

Usman, Muhammad Sani; Ibrahim, Nor Azowa; Shameli, Kamyar; Zainuddin, Norhazlin; Yunus, Wan Md Zin Wan

2012-12-14

Herein we report a synthesis of copper nanoparticles (Cu-NPs) in chitosan (Cts) media via a chemical reaction method. The nanoparticles were synthesized in an aqueous solution in the presence of Cts as stabilizer and CuSO(4)·5H(2)O precursor. The synthesis proceeded with addition of NaOH as pH moderator, ascorbic acid as antioxidant and hydrazine( )as the reducing agent. The characterization of the prepared NPs was done using ultraviolet-visible spectroscopy, which showed a 593 nm copper band. The Field Emission Scanning Electron Microscope (FESEM) images were also observed, and found to be in agreement with the UV-Vis result, confirming the formation of metallic Cu-NPs. The mean size of the Cu-NPs was estimated to be in the range of 35-75 nm using X-ray diffraction. XRD was also used in analysis of the crystal structure of the NPs. The interaction between the chitosan and the synthesized NPs was studied using Fourier transform infrared (FT-IR) spectroscopy, which showed the capping of the NPs by Cts.

Novel Green Synthesis and Characterization of Nanopolymer ...

African Journals Online (AJOL)

Purpose: To develop a novel approach to green synthesis of nano-polymer porous gold oxide nanoparticles, and examine the effects of the temperatures on their surface. Methods: Green synthesis of nano-polymer porous gold oxide nanoparticles (GONPs) using cetyle trimethylammonium bromide (CTAB) surfactant with a ...

Synthesis and antibacterial characterization of sustainable nanosilver using naturally-derived macromolecules

Energy Technology Data Exchange (ETDEWEB)

Osonga, Francis J.; Kariuki, Victor M.; Yazgan, Idris; Jimenez, Apryl; Luther, David; Schulte, Jürgen; Sadik, Omowunmi A., E-mail: osadik@binghamton.edu

2016-09-01

Greener nanosynthesis utilizes fewer amounts of materials, water, and energy; while reducing or replacing the need for organic solvents. A novel approach is presented using naturally-derived flavonoids including Quercetin pentaphosphate (QPP), Quercetin sulfonic acid (QSA) and Apigenin Triphosphate (ATRP). These water soluble, phosphorylated flavonoids were utilized both as reducing agent and stabilizer. The synthesis was achieved at room temperature using water as a solvent and it requires no capping agents. The efficiency of the resulting silver nanoparticle synthesis was compared with naturally-occurring flavonoid such as Quercetin (QCR). Results show that QCR reduced Ag{sup +} faster followed by QPP, QSA and ATRP respectively. This is the first evidence of direct utilization of QCR for synthesis of silver nanoparticles (AgNPs) in water. The percentage conversion of Ag{sup +} to Ag{sup 0} was determined to be 96% after 35 min. The synthesized nanoparticles were characterized using Transmission electron microscopy (TEM), Energy dispersive absorption spectroscopy (EDS), UV–vis spectroscopy, High resolution TEM (HR-TEM) with selected area electron diffraction (SAED). The particle sizes ranged from 2 to 80 nm with an average size of 22 nm and in the case of ATRP, the nanoparticle shapes varied from spherical to hexagonal with dispersed particle size ranging from 2 to 30 nm. Crystallinity was confirmed by XRD and the SAED of (111), (200), and the fringes observed in HRTEM images. Results were in agreement with the UV resonance peaks of 369–440 nm. The particles also exhibit excellent antibacterial activity against Staphylococcus epidermidis, Escherichia coli and Citrobacter freundii in water. - Highlights: • Greener nanosilver prepared using flavonoid derivatives • Synthesized nanosilver exhibits exhibit antibacterial activity. • Approach suitable for industrial synthesis.

Polypyrrole–titanium(IV) doped iron(III) oxide nanocomposites: Synthesis, characterization with tunable electrical and electrochemical properties

International Nuclear Information System (INIS)

Nandi, Debabrata; Ghosh, Arup Kumar; Gupta, Kaushik; De, Amitabha; Sen, Pintu; Duttachowdhury, Ankan; Ghosh, Uday Chand

2012-01-01

Highlights: ► Synthesis and characterization of polymer nanocomposite based on titanium doped iron(III) oxide. ► Electrical conductivity increased 100 times in composite with respect to polymer. ► Electrochemical capacitance of polymer composites increased with nanooxide content. ► Thermal stability of the polymer enhanced with nano oxide content. -- Abstract: Titanium(IV)-doped synthetic nanostructured iron(III) oxide (NITO) and polypyrrole (PPy) nanocomposites was fabricated by in situ polymerization using FeCl 3 as initiator. The polymer nanocomposites (PNCs) and pure NITO were characterized by X-ray diffraction, Föurier transform infrared spectroscopy, scanning electron microscopy, electron dispersive X-ray spectroscopy, transmission electron microscopy, etc. Thermo gravimetric and differential thermal analyses showed the enhancement of thermal stability of PNCs than the pure polymer. Electrical conductivity of the PNCs had increased significantly from 0.793 × 10 −2 S/cm to 0.450 S/cm with respect to the PPy, and that had been explained by 3-dimensional variable range hopping (VRH) conduction mechanisms. In addition, the specific capacitance of PNCs had increased from 147 F/g to 176 F/g with increasing NITO content than that of pure NITO (26 F/g), presumably due to the growing of mesoporous structure with increasing NITO content in PNCs which reduced the charge transfer resistance significantly.

SYNTHESIS, CHARACTERIZATION AND DENSITY FUNCTIONAL ...

African Journals Online (AJOL)

Preferred Customer

We synthesized a number of aniline derivatives containing acyl groups to compare their barriers of rotation around ... KEY WORDS: Monoacyl aniline, Synthesis, Density functional theory, Rotation barrier. INTRODUCTION. Developments in ...

Tuned apatitic materials: Synthesis, characterization and potential antimicrobial applications

Science.gov (United States)

Fierascu, Irina; Fierascu, Radu Claudiu; Somoghi, Raluca; Ion, Rodica Mariana; Moanta, Adriana; Avramescu, Sorin Marius; Damian, Celina Maria; Ditu, Lia Mara

2018-04-01

Inorganic antimicrobial materials can be viable for multiple applications (related to its use for new buildings with special requirements related to microbiological loading, such as hospital buildings and for consolidation of cultural heritage constructions); also the use of substituted hydroxyapatites for protection of stone artefacts against environmental factors (acidic rain) and biodeterioration it's an option to no longer use of toxic substances. This paper presents methods of synthesis and characterization of the material from the point of view of the obtained structures and final applications. The materials were characterized in terms of composition and morphology (using X-ray Diffraction, X-ray Fluorescence, Inductively coupled plasma-atomic emission spectrometry, Fourier Transform Infrared Spectroscopy, X-ray Photoelectron Spectroscopy, Surface area and pore size determination). Antimicrobial activity was tested against filamentous fungi strains and pathogenic bacteria strains, using both spot on lawn qualitative method (on agar medium) and serial microdilution quantitative method (in broth medium). Further, it was evaluated the anti-biofilm activity of the tested samples toward the most important microbial strains implicated in biofilm development, using crystal violet stained biofilms microtiter assay, followed by spectrophotometric quantitative evaluation.

SYNTHESIS AND CHARACTERIZATION OF FUNCTIONALIZED ...

African Journals Online (AJOL)

In addition, these compounds have emerged as potential calcium ... As a consequence, the synthesis of dihydropyrimidinone derivatives has ..... Ramazani, A.; Shaghaghi,Z.; Aghahosseini, H.; Asiabi, P.A.; Joo, S.W. Silica nanoparticles.

Synthesis and characterization of functional magnetic nanocomposites

Science.gov (United States)

Gass, J.; Sanders, J.; Srinath, S.; Srikanth, H.

2006-03-01

Magnetic nanoparticles and carbon nanotubes have been excellent functional materials that could be dispersed in polymer matrices for various applications. However, uniform dispersion of particles in polymers without agglomeration is quite challenging. We have fabricated PMMA/polypyrrole bilayer structures embedded with Fe3O4 magnetite nanoparticles synthesized using wet chemical synthesis. Agglomeration-free dispersion of nanoparticles was achieved by coating the particles with surfactants and by dissolving both the particles and PMMA in chlorobenzene. Structural characterization was done using XRD and TEM. Magnetic properties of the bilayer structures indicated superparamagnetic behavior that is desirable for RF applications as the magnetic losses are reduced. Our polymer nanocomposite bilayer films with conducting polymer coatings are potential candidates for tunable RF applications with integrated EMI suppression. We will also report on our studies of pumped ferrofluids flowing past carbon nanotubes that are arranged in microchannel arrays. Magnetization under various flow conditions is investigated and correlated with the hydrodynamic properties. This scheme provides a novel method of energy conversion and storage using nanocomposite materials.

Synthesis of thermoplastic elastomer using potassium persulfate and ammonium peroxydisulfate initiator

International Nuclear Information System (INIS)

Dewi Sondari; Agus Haryono; M Ghozali; Ahmad Randy; Kuntari Adi Suhardjo; Ariyadi B; Surasno

2010-01-01

Thermoplastic elastomer is polymeric material that has elastomer and thermoplastic properties. This material can be easily molded into finished and recyclable goods, thus environmentally safe for long term application. In this study we synthesize thermoplastic elastomer using two initiator that are potassium persulfate and ammonium peroxydisulfate with natural rubber to monomer (styrene/methyl methacrylate) ratio of 50 : 50 and 60 : 40 (v/v). The process of thermoplastic elastomer synthesis was conducted with emulsion grafting polymerization method for 6 hours at 65 °C. We used sodium dodecyl sulfate as emulsifier. FT-IR analysis result shows that grafting process had already occurred shown by new peaks that were observed in 1743 and 1519 cm"-"1. These peaks was assigned to carbonyl (C=O) group of methyl methacrylate and C=C benzene of styrene respectively. From "1H-NMR new peaks at δ = 7.1 ppm was aromatic proton from phenyl group of styrene, at δ = 3.5 ppm was methoxy proton of grafted methyl methacrylate acrylic group, and at δ = 5.1 ppm that is resonance of isoprene methine proton. This result showed that methyl methacrylate and styrene had already grafted onto natural rubber backbone. Initiator influenced grafting efficiency. Potassium persulfate gave 97.6 % grafting efficiency while ammonium peroxydisulfate gave 90.2 % grafting efficiency. (author)

Initial Characterization of the Wave Resource at Several High Energy U.S. Sites

OpenAIRE

Dallman, Ann; Neary, Vincent S.

2014-01-01

Wave energy resource characterization efforts are critical for developing knowledge of the physical conditions experienced by wave energy converter (WEC) devices and arrays. Developers are lacking a consistent characterization of possible wave energy test sites, and therefore Sandia National Laboratories (SNL) has been tasked with developing a catalogue characterizing three high energy U.S. test sites. The initial results and framework for the catalogue are discussed in this paper. U.S. De...

Synthesis and characterization of novel dual-responsive nanogels and their application as drug delivery systems

Science.gov (United States)

Peng, Jinrong; Qi, Tingting; Liao, Jinfeng; Fan, Min; Luo, Feng; Li, He; Qian, Zhiyong

2012-03-01

In this study, a temperature/pH dual-response nanogel based on NIPAm, MAA, and PEGMA was synthesized via emulsion polymerization and characterized by 1H-NMR, FT-IR, TEM and DLS. By introducing a novel initiator, through which PEG-AIBN-PEG was synthesized, it was revealed that the PEG segments from PEG-AIBN-PEG with a dosage of initiator had a significant influence over the macro-state and stability of the nanogels. In order to optimize the feeding prescription for better application as a drug delivery system, the effect of the co-monomer contents on the response to stimuli (temperature and pH value) and cytotoxicity of the nanogels has been studied in detail. The results demonstrated that the responsiveness, reversibility and volume phase transition critical value of the nanogels could be controlled by adjusting the feeding ratio of the co-monomers in the synthesis process. MTT assay results revealed that nanogels with appropriate compositions showed good biocompatibility and relatively low toxicity. Most importantly, by studying the drug loading behavior, it was found that the dimensions of the drug molecules had a considerable influence on the drug loading efficiency and loading capacity of the nanogels, and that the mechanism by which drug molecule sizes influence the drug loading behavior of nanogels needs further investigation. The results indicated that such PNMP nanogels might have potential applications in drug delivery and other medical applications, but that the drug loading mechanism must be further developed.

Synthesis and characterization of an additive type super plasticizers obtained from plastics cups of polystyrene

International Nuclear Information System (INIS)

Araujo, Carolina G.L.; Freire, Carolina B.; Tello, Cledola C. de O.

2013-01-01

This paper aims to describe the synthesis of an additive type superplasticizer from alternative material - plastic cups used of polystyrene - and characterize it physically and chemically in order to verify their efficiency and compare it with a commercial use superplasticizer. Following the search, the synthesized superplasticizer is used in mortars to assess their efficiency

Synthesis and characterization of surfactant assisted Mn2+ doped ZnO nanocrystals

Directory of Open Access Journals (Sweden)

N. Shanmugam

2016-09-01

Full Text Available We report the synthesis and characterization of Mn doped ZnO nanocrystals, both in the free standing and PVP capped particle forms. The nanocrystals size could be controlled by capping them with polyvinylpyrollidone and was estimated by X-ray diffraction and transmission electron microscopy. The chemical compositions of the products were characterized by FT-IR spectroscopy. UV–Vis absorption spectroscopy measurements reveal that the capping of ZnO leads to blue shift due to quantum confinement effect. The morphology of the particles was evaluated by Scanning Electron Microscopy (SEM and Transmission Electron Microscopy (TEM. Both the Thermo Gravimetric Analysis (TGA and Differential Thermal Analysis (DTA curves of the ZnO show no further weight loss and thermal effect at a temperature above 510 °C.

Synthesis and structural characterization of coaxial nano tubes intercalated of molybdenum disulfide with carbon

International Nuclear Information System (INIS)

Reza San German, C.M.

2005-01-01

In this work the study of some fundamental aspects in the growth of unidimensional systems of coaxial nano tubes from the mold method is approached. This method is an inclusion technique of a precursor reagent into oxide nano porous alumina film (mold), and later applying some processes of synthesis it is gotten to obtain the wished material. The synthesized structures are identified later because they take place by means of the initial formation of nano tubes of MoS 2 , enclosing to carbon nano tubes by the same method, with propylene flow which generates a graphitization process that 'copy' the mold through as it flows. Binary phase MoS 2 + C nano tubes were synthesized by propylene pyrolysis inside MoS 2 nano tubes prepared by template assisted technique. The large coaxial nano tubes constituted of graphite sheets inserted between the MoS 2 layers forming the outer part, and coaxial multi wall carbon nano tubes (MWCNT) intercalated with MoS 2 inside. High resolution electron microscopy (HRTEM), electron energy loss spectroscopy (EELS), high angle annular dark field (HAADF), gatan image filter (GIF), nano beam electron diffraction patterns (NBEDP), along with molecular dynamics simulation and quantum mechanical calculations were used to characterize the samples. The one-dimensional structures exhibit diverse morphologies such as long straight and twisted nano tubes with several structural irregularities. The inter-planar spacing between MoS 2 layers was found to increase from 6.3 to 7.4 A due to intercalation with carbon. Simulated HREM images revealed the presence of these twisted nano structures, with mechanical stretch into intercalate carbon between MoS 2 layers. Our results open up the possibility of using MoS 2 nano tubes as templates for the synthesis of new one- dimensional binary phase systems. (Author)

Preliminary studies of consolidation of wall paintings: synthesis and characterisation of nanolime

Directory of Open Access Journals (Sweden)

Penka I. Girginova

2016-01-01

Full Text Available In this publication, we report the synthesis and characterization of calcium and magnesium hydroxides nanoparticles for consolidation of mural paintings. Some preliminary results are discussed. This research is the initial part of our ongoing project which aims to develop new synthetic strategies towards novel and innovative materials for preservation and restoration of old renders.

Synthesis and characterization of oxovanadium (IV) dithiocarbamates with pyridine

Energy Technology Data Exchange (ETDEWEB)

Doadrio, Antonio L.; Sotelo, Jose; Fernandez-Ruano, Ana [Universidad Complutense, Madrid (Spain). Facultad de Farmacia. Dept. de Quimica Inorganica y Bioinorganica]. E-mail: antoniov@farm.ucm.es

2002-07-01

We report the synthesis and study of a new series of oxovanadium (IV) dithiocarbamate adducts and derivatives with pyridine and cyclohexyl, di-iso-butyl, di-n-propyl, aniline, morpholine, piperidine and di-iso-propyl amines. The complexes have been characterized by analytical, magneto chemical, IR, visible-UV spectral and thermal studies, and are assigned the formulas [VO(L){sub 2}].py, where L=cyclohexyl, di-iso-butyl, di-n-propyl, aniline dithiocarbamate and [VO(OH)(L)(py){sub 2}] OH.H{sub 2}O (L=morpholine, piperidine and di-iso-propyl dithiocarbamate). The effect of the adduct formation on the p{sub V=0} bound is discussed in terms of the IR (V=O, V-S and V-N stretching frequencies) and electronic spectra (d-d transitions). (author)

Synthesis and characterization of monodispersed orthorhombic manganese oxide nanoparticles produced by Bacillus sp. cells simultaneous to its bioremediation

Energy Technology Data Exchange (ETDEWEB)

Sinha, Arvind [Enzyme and Microbial Biochemistry Laboratory, Department of Chemistry, Indian Institute of Technology, Delhi, Hauz Khas, New Delhi 110 016 (India); Singh, Vidya Nand; Mehta, Bodh Raj [Thin Film Laboratory, Department of Physics, Indian Institute of Technology, Delhi Hauz Khas, New Delhi 110016 (India); Khare, Sunil Kumar, E-mail: skhare@rocketmail.com [Enzyme and Microbial Biochemistry Laboratory, Department of Chemistry, Indian Institute of Technology, Delhi, Hauz Khas, New Delhi 110 016 (India)

2011-08-30

Highlights: {yields} An efficient process wherein remediated manganese is synthesized into nanoparticles. {yields} A microbial process for manganese nanoparticle synthesis from metal waste streams. {yields} Nanoparticles characterized as monodispersed, spherical and 4.62 {+-} 0.14 nm sized MnO{sub 2}. -- Abstract: A heavy metal resistant strain of Bacillus sp. (MTCC10650) is reported. The strain exhibited the property of bioaccumulating manganese, simultaneous to its remediation. The nanoparticles thus formed were characterized and identified using energy dispersive X-ray analysis (EDAX), high resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (PXRD) and atomic force microscopy (AFM). When the cells were challenged with manganese, the cells effectively synthesized nanoparticles of average size 4.62 {+-} 0.14 nm. These were mostly spherical and monodispersed. The ex situ enzymatically synthesized nanoparticles exhibited an absorbance maximum at 329 nm. These were more discrete, small and uniform, than the manganese oxide nanoparticles recovered after cell sonication. The use of Bacillus sp. cells seems promising and advantageous approach. Since, it serves dual purposes of (i) remediation and (ii) nanoparticle synthesis. Considering the increasing demand of developing environmental friendly and cost effective technologies for nanoparticle synthesis, these cells can be exploited for the remediation of manganese from the environment in conjunction with development of a greener process for the controlled synthesis of manganese oxide nanoparticles.

Synthesis and characterization of monodispersed orthorhombic manganese oxide nanoparticles produced by Bacillus sp. cells simultaneous to its bioremediation

International Nuclear Information System (INIS)

Sinha, Arvind; Singh, Vidya Nand; Mehta, Bodh Raj; Khare, Sunil Kumar

2011-01-01

Highlights: → An efficient process wherein remediated manganese is synthesized into nanoparticles. → A microbial process for manganese nanoparticle synthesis from metal waste streams. → Nanoparticles characterized as monodispersed, spherical and 4.62 ± 0.14 nm sized MnO 2 . -- Abstract: A heavy metal resistant strain of Bacillus sp. (MTCC10650) is reported. The strain exhibited the property of bioaccumulating manganese, simultaneous to its remediation. The nanoparticles thus formed were characterized and identified using energy dispersive X-ray analysis (EDAX), high resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (PXRD) and atomic force microscopy (AFM). When the cells were challenged with manganese, the cells effectively synthesized nanoparticles of average size 4.62 ± 0.14 nm. These were mostly spherical and monodispersed. The ex situ enzymatically synthesized nanoparticles exhibited an absorbance maximum at 329 nm. These were more discrete, small and uniform, than the manganese oxide nanoparticles recovered after cell sonication. The use of Bacillus sp. cells seems promising and advantageous approach. Since, it serves dual purposes of (i) remediation and (ii) nanoparticle synthesis. Considering the increasing demand of developing environmental friendly and cost effective technologies for nanoparticle synthesis, these cells can be exploited for the remediation of manganese from the environment in conjunction with development of a greener process for the controlled synthesis of manganese oxide nanoparticles.

Synthesis and transport characterization of electrochemically deposited CdTe nanowires

Science.gov (United States)

Kaur, Jaskiran; Kaur, Harmanmeet; Singh, R. C.

2018-04-01

This paper reports the synthesis and characterization of CdTe nanowires. A thin polymeric films were irradiated with 80MeV Ag ions at a fluence of 8E7 ions/cm2, followed by UV irradiation and chemically etching in aqueous NaOH. Nanosizes go-through pores so formed were filled using a specially designed cell via electrodeposition. Nanowires so formed were further studied using SEM, I-V, UV and XRD analysis. SEM images show very smooth and uniform CdTe nanowires freely standing on the substrate. The in-situ I-V characteristics of nano-/micro structures was carried out at room temperature by leaving the structures embedded in the insulating template membrane itself.

Synthesis and characterization of PMMA/clay nanocomposites prepared by in situ polymerization assisted by sonication

International Nuclear Information System (INIS)

Prado, Bruna R.; Bartoli, Julio R.; Ito, Edson N.

2015-01-01

In this work is presented the synthesis of nanocomposites of poly(methyl methacrylate), PMMA, with organically montmorillonite (OMMT) modified clays by in situ polymerization assisted by sonication. A statistically designed experiment was used, central composing design (CCD), to study the effect of synthesis variables on the dispersion of nanoparticles in PMMA matrix. The processing and formulation factors studied were: energy of sonication and Flory-Huggins interaction parameter between PMMA and organoclay. The structural (XRD) and morphological (TEM) characterizations of the PMMA/OMMT nanocomposites are compared with the literature. It was observed significant exfoliation of OMMT modified with hydroxyl groups in the nanocomposites of PMMA, mainly at the low ultrasonic energy level (90 and 105 kJ) studied. (author)

Graphitic carbon nitride: Synthesis, characterization and photocatalytic decomposition of nitrous oxide

Energy Technology Data Exchange (ETDEWEB)

Praus, Petr, E-mail: petr.praus@vsb.cz [Institute of Environmental Technology, VŠB-Technical University of Ostrava, 17. Listopadu 15/2172, Ostrava 708 33 (Czech Republic); Department of Chemistry, Faculty of Metallurgy and Materials Engineering, VŠB-Technical University of Ostrava, 17. Listopadu 15/2172, Ostrava 708 33 (Czech Republic); Svoboda, Ladislav [Institute of Environmental Technology, VŠB-Technical University of Ostrava, 17. Listopadu 15/2172, Ostrava 708 33 (Czech Republic); Department of Chemistry, Faculty of Metallurgy and Materials Engineering, VŠB-Technical University of Ostrava, 17. Listopadu 15/2172, Ostrava 708 33 (Czech Republic); Ritz, Michal [Department of Chemistry, Faculty of Metallurgy and Materials Engineering, VŠB-Technical University of Ostrava, 17. Listopadu 15/2172, Ostrava 708 33 (Czech Republic); Troppová, Ivana; Šihor, Marcel; Kočí, Kamila [Institute of Environmental Technology, VŠB-Technical University of Ostrava, 17. Listopadu 15/2172, Ostrava 708 33 (Czech Republic)

2017-06-01

Graphitic carbon nitride (g-C{sub 3}N{sub 4}) was synthetized by condensation of melamine at the temperatures of 400–700 °C in air for 2 h and resulting products were characterized and finally tested for the photocatalytic decomposition of nitrous oxide. The characterization methods were elemental analysis, UV–Vis diffuse reflectance spectroscopy (DRS), photoluminescence (PL), Fourier transform infrared (FTIR) and Raman spectroscopy, measurement of specific surface area (SSA), X-ray powder diffraction (XRD), scanning (SEM) and transmission (TEM) electron microscopy. The XRD patterns, FTIR and Raman spectra proved the presence of g-C{sub 3}N{sub 4} at above 550 °C but the optimal synthesis temperature of 600–650 °C was found. Under these conditions graphitic carbon nitride of the overall empirical composition of C{sub 6}N{sub 9}H{sub 2} was formed. At lower temperatures g-C{sub 3}N{sub 4} with a higher content of hydrogen was formed but at higher temperatures g-C{sub 3}N{sub 4} was decomposed. At the temperatures above 650 °C, its exfoliation was observed. The photocatalytic experiments showed that the activity of all the samples synthetized at 400–700 °C was very similar, that is, within the range of experimental error (5 %). The total conversion of N{sub 2}O reached about 43 % after 14 h. - Highlights: • Graphitic carbon nitride (g-C{sub 3}N{sub 4}) was thermally synthetized from melamine in the range of 400–700 °C. • The optimal temperature was determined at 600–650 °C. • All synthesis products were properly characterized by physico-chemical methods. • Exfoliation of g-C{sub 3}N{sub 4} at above 600 °C was observed. • g-C{sub 3}N{sub 4} was used for the photocatalytic decomposition of N{sub 2}O.

Synthesis and characterization of MgO nanocrystals for biosensing applications

Energy Technology Data Exchange (ETDEWEB)

Li, Hongji [Tianjin Key Laboratory of Organic Solar Cells and Photochemical Conversion, School of Chemistry & Chemical Engineering, Tianjin University of Technology, Tianjin 300384 (China); Li, Mingji, E-mail: limingji@163.com [Tianjin Key Laboratory of Film Electronic and Communication Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China); Qiu, Guojun [Tianjin Key Laboratory of Organic Solar Cells and Photochemical Conversion, School of Chemistry & Chemical Engineering, Tianjin University of Technology, Tianjin 300384 (China); Li, Cuiping; Qu, Changqing; Yang, Baohe [Tianjin Key Laboratory of Film Electronic and Communication Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China)

2015-05-25

Highlights: • MgO nanocrystals were prepared using DC arc plasma jet CVD method. • The growth time does not exceed 10 min in process of the synthesis. • The samples were found to consist of cubic MgO nanobelts and nanosheets. • Nanocrystals contain contacts, rough edges, vacancies, and doping defects. • The samples exhibited excellent electrochemical biosensing properties. - Abstract: MgO nanocrystals were prepared using a simple direct current arc plasma jet chemical vapor deposition method. Magnesium nitrate was used as source material and Mo film was used as a substrate and catalyst. The high-temperature plasma produced ensured rapid synthesis of the MgO nanocrystals. The as-prepared nanocrystals were characterized by field-emission scanning electron microscopy, high-resolution transmission electron microscopy, X-ray diffraction, energy-dispersive spectroscopy, Fourier transform infrared spectrometry, ultraviolet–visible spectrophotometry, and photoluminescence measurements. The as-synthesized samples were found to consist of cubic MgO nanobelts and nanosheets with large surface areas and low coordination oxide ions, and contained numerous contacts, rough edges, vacancies, and doping defects. The nanostructures exhibited excellent electrochemical sensing properties with high-sensing sensitivity toward ascorbic acid. Their high electrocatalytic activity was attributed to the effect of defects and the surface electron transfer ability of the one-dimensional MgO nanobelts.

Synthesis, characterization, spectroscopic properties and DFT study of a new pyridazinone family

Science.gov (United States)

Arrue, Lily; Rey, Marina; Rubilar-Hernandez, Carlos; Correa, Sebastian; Molins, Elies; Norambuena, Lorena; Zarate, Ximena; Schott, Eduardo

2017-11-01

Nitrogen compounds are widely investigated due to their pharmacological properties such as antihypertensive, antinociceptive, antibacterial, antifungal, analgesic, anticancer and inhibition activities and lately even as pesticide. In this context, we present the synthesis of new compounds: (E)-6-(3,4-dimethoxyphenyl)-3-(3-(3,4-dimethoxyphenyl)acryloyl)-1-(4-R-phenyl)- 5,6-dihydropyridazin-4(1H)-one (with R = sbnd H(1), -Cl(2), -Br(3), sbnd I(4) and sbnd COOH(5)) that was carried out by reaction of (1E, 6E)-1,7-bis(3,4-dimethoxyphenyl)hepta-1,6-diene-3,5-dione with a substituted phenylamine with general formula p-R-C6H4sbnd NH2 (R = sbnd H (1), sbnd Cl (2), -Br(3), sbnd I(4) and sbnd COOH(5)). This is the first synthesis report of a pyridazinone using as precursors a curcuminoid derivative and a diazonium salt formed in situ. All compounds were characterized by EA, FT-IR, UV-Vis, Emission,1H- and13C-NMR spectroscopy and the crystalline and molecular structure of 4 was solved by X-rays diffraction method. DFT and TD-DFT quantum chemical calculations were also employed to characterize the compounds and provide a rational explanation to the spectroscopic properties. To assess the biological activity of the systems, we focused on pesticide tests on compound 2, which showed an inhibitory effect in plant growth of Agrostis tenuis Higland.

Hydrothermal synthesis and characterization of zirconia based catalysts

Science.gov (United States)

Caillot, T.; Salama, Z.; Chanut, N.; Cadete Santos Aires, F. J.; Bennici, S.; Auroux, A.

2013-07-01

In this work, three equimolar mixed oxides ZrO2/CeO2, ZrO2/TiO2, ZrO2/La2O3 and a reference ZrO2 have been synthesized by hydrothermal method. The structural and surface properties of these materials have been fully characterized by X-ray diffraction, transmission electron microscopy, surface area measurement, chemical analysis, XPS, infrared spectroscopy after adsorption of pyridine and adsorption microcalorimetry of NH3 and SO2 probe molecules. All investigated mixed oxides are amphoteric and possess redox centers on their surface. Moreover, hydrothermal synthesis leads to catalysts with higher surface area and with better acid-base properties than classical coprecipitation method. Both Lewis and Brønsted acid sites are present on the surface of the mixed oxides. Compared to the other samples, the ZrO2/TiO2 material appears to be the best candidate for further application in acid-base catalysis.

Synthesis and characterization of new ionic liquids; Sintese e caracterizacao de novos liquidos ionicos

Energy Technology Data Exchange (ETDEWEB)

Oliveira, L.M.C. de; Mattedi, S.; Boaventura, J.S., E-mail: luanaufrn@hotmail.co [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Escola Politecnica. Programa de Pos-Graduacao em Engenharia Quimica; Iglesias, M. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Escola Politecnica. Programa de Pos-Graduacao em Engenharia Quimica; Universidad de Santiago de Compostela (Spain). Escuela Tecnica Superior de Ingenieria. Dept. de Ingenieria Quimica

2010-07-01

In recent years, ionic liquids have been highlighted for its potential in various industrial applications. Among them, the salts of Broensted has a promising profile for the low toxicity, low cost and simple synthesis. This paper presents the synthesis and characterization of new salts of Bronsted with branched (lactate) or large chain anions (oleate) for future use as additives promoters of proton conductivity in fuel cells of ethanol. Experimental data were measured for density, sound velocity and conductivity of pure ionic liquids and mixtures. The density decreases linearly with increasing temperature, and sound velocity shows a similar trend, but not linear. The conductivity increases according to the Arrhenius model with activation energy less than 10 J/mol. Tests NMR, FTIR and TGA confirm ionic structure and thermal stability up to 165 deg C. (author)

Design, synthesis, and characterization of new phosphazene related materials, and study the structure property correlations

Science.gov (United States)

Tian, Zhicheng

The work described in this thesis is divided into three major parts, and all of which involve the exploration of the chemistry of polyphosphazenes. The first part (chapters 2 and 3) of my research is synthesis and study polyphoshazenes for biomedical applications, including polymer drug conjugates and injectable hydrogels for drug or biomolecule delivery. The second part (chapters 4 and 5) focuses on the synthesis of several organic/inorganic hybrid polymeric structures, such as diblock, star, brush and palm tree copolymers using living cationic polymerization and atom transfer radical polymerization techniques. The last part (chapters 6 and 7) is about exploratory synthesis of new polymeric structures with fluorinated side groups or cycloaliphatic side groups, and the study of new structure property relationships. Chapter 1 is an outline of the fundamental concepts for polymeric materials, as such the history, important definitions, and some introductory material for to polymer chemistry and physics. The chemistry and applications of phopshazenes is also briefly described. Chapter 2 is a description of the design, synthesis, and characterization of development of a new class of polymer drug conjugate materials based on biodegradable polyphosphazenes and antibiotics. Poly(dichlorophosphazene), synthesized by a thermal ring opening polymerization, was reacted with up to 25 mol% of ciprofloxacin or norfloxacin and three different amino acid esters (glycine, alanine, or phenylalanine) as cosubstituents via macromolecular substitutions. Nano/microfibers of several selected polymers were prepared by an electrospinning technique. Chapter 3 is concerned with the development of a class of injectable and biodegradable hydrogels based on water-soluble poly(organophosphazenes) containing oligo(ethylene glycol) methyl ethers and glycine ethyl esters. The hydrogels can be obtained by mixing alpha-cyclodextrin aqueous solution and poly(organophosphazenes) aqueous solution in

Synthesis and Characterization of New Polyamides from 1,2-Bis hydrazine Derivatives

International Nuclear Information System (INIS)

Salaha, A.; Abdel-Bary, E.M.; Kandilea, N.G.

2005-01-01

Preparation of polyamides having different chemical structures allows obtaining new materials with different mechanical and physical properties. The difference in the chemical structure depends mainly on the starting reactants used in condensation polymerization of polyamides. In this paper the synthesis of new polyamides based on the condensation polymerization of 1,2- Bis(3-carboxyacryloyl or carboxybenzoyl) hydrazine derivatives and various diamines has been described. The polymers obtained were characterized using spectroscopic and X-ray analysis. Besides thermal stability and electrical conductivity have been evaluated and correlated with the chemical structure of the polyamides obtained

Synthesis and characterization of platinum supported on alumina doped with cerium catalyst

International Nuclear Information System (INIS)

Yusof Abdullah; Abd Fatah Awang Mat; Mohd Ali Sufi; Sarimah Mahat; Razali Kassim; Nurhaslinda Abdullah.

1996-03-01

The synthesis and characterization of gamma-alumina doped with cerium as platinum support for the automobile exhaust catalyst are described. Platinum/alumina/ceria catalyst were prepared by impregnation of hexachloroplatinic acid and sintered at 500 degree Celsius to obtain metal dispersions of 1.0 wt%. Catalyst distribution inside the powder and the effects of the addition of cerium to alumina were analyzed by the scanning electron microscopy (SEM) and x-ray fluorescence spectroscopy (XRF). The results showed that the alumina - supported catalysts contained well dispersion of the noble metal

Polyhomologation based on in situ generated Boron-thexyl-silaboracyclic initiating sites: a novel strategy towards the synthesis of polyethylene-based complex architectures

KAUST Repository

Zhang, Zhen; Zhang, Hefeng; Gnanou, Yves; Hadjichristidis, Nikolaos

2015-01-01

A novel strategy, based on the in situ generated Boron-thexyl-silaboracyclic initiating sites for the polyhomologation of dimethylsulfoxonium methylide, has been developed for the synthesis of complex polyethylene-based architectures. As examples

Synthesis of Cyclic Polymers and Characterization of Their Diffusive Motion in the Melt State at the Single Molecule Level

KAUST Repository

Habuchi, Satoshi

2016-09-26

We demonstrate a method for the synthesis of cyclic polymers and a protocol for characterizing their diffusive motion in a melt state at the single molecule level. An electrostatic self-assembly and covalent fixation (ESA-CF) process is used for the synthesis of the cyclic poly(tetrahydrofuran) (poly(THF)). The diffusive motion of individual cyclic polymer chains in a melt state is visualized using single molecule fluorescence imaging by incorporating a fluorophore unit in the cyclic chains. The diffusive motion of the chains is quantitatively characterized by means of a combination of mean-squared displacement (MSD) analysis and a cumulative distribution function (CDF) analysis. The cyclic polymer exhibits multiple-mode diffusion which is distinct from its linear counterpart. The results demonstrate that the diffusional heterogeneity of polymers that is often hidden behind ensemble averaging can be revealed by the efficient synthesis of the cyclic polymers using the ESA-CF process and the quantitative analysis of the diffusive motion at the single molecule level using the MSD and CDF analyses.

Carbazole Containing Copolymers: Synthesis, Characterization, and Applications in Reversible Holographic Recording

Directory of Open Access Journals (Sweden)

Bénédicte Mailhot-Jensen

2010-01-01

Full Text Available Carbazolic copolymers have been developed to be used in reversible holographic recording. This paper describes a complete analysis, from synthesis of the material to its applications, together with the corresponding characterizations. The investigated materials were photosensitive copolymers obtained from carbazolylalkylmethacrylates (CEM and octylmethacrylate (OMA. A detailed investigation was undertaken involving infrared spectroscopy and NMR techniques, 1H, 13C, COSY, and HSQC, in order to establish the chemical structure and the composition of the copolymers. Holographic recording characteristics were investigated with one- and two-layer photothermoplastic carriers. The two-layer carrier contains separate photosensitive and thermoplastic layers and gives the best holographic response. The surface of microstructured samples has been characterized by atomic force microscopy analysis. It is shown that via a photothermoplastic recording process, it is possible to record and read holograms practically in real time (~3 s with a diffraction efficiency of 10% and a spatial resolution higher than 1000 mm−1.

Ion beams provided by small accelerators for material synthesis and characterization

Science.gov (United States)

Mackova, Anna; Havranek, Vladimir

2017-06-01

The compact, multipurpose electrostatic tandem accelerators are extensively used for production of ion beams with energies in the range from 400 keV to 24 MeV of almost all elements of the periodic system for the trace element analysis by means of nuclear analytical methods. The ion beams produced by small accelerators have a broad application, mainly for material characterization (Rutherford Back-Scattering spectrometry, Particle Induced X ray Emission analysis, Nuclear Reaction Analysis and Ion-Microprobe with 1 μm lateral resolution among others) and for high-energy implantation. Material research belongs to traditionally progressive fields of technology. Due to the continuous miniaturization, the underlying structures are far beyond the analytical limits of the most conventional methods. Ion Beam Analysis (IBA) techniques provide this possibility as they use probes of similar or much smaller dimensions (particles, radiation). Ion beams can be used for the synthesis of new progressive functional nanomaterials for optics, electronics and other applications. Ion beams are extensively used in studies of the fundamental energetic ion interaction with matter as well as in the novel nanostructure synthesis using ion beam irradiation in various amorphous and crystalline materials in order to get structures with extraordinary functional properties. IBA methods serve for investigation of materials coming from material research, industry, micro- and nano-technology, electronics, optics and laser technology, chemical, biological and environmental investigation in general. Main research directions in laboratories employing small accelerators are also the preparation and characterization of micro- and nano-structured materials which are of interest for basic and oriented research in material science, and various studies of biological, geological, environmental and cultural heritage artefacts are provided too.

Synthesis, characterization and application of nanozeolite NaX from Vietnamese kaolin

International Nuclear Information System (INIS)

Ngoc, Don Ta; Pham, Thanh Huyen; Hong Nguyen, Khanh Dieu

2013-01-01

This paper presents the results of synthesis of nanozeolite NaX from Vietnamese kaolin. Influence factors on the control of crystal sizes and application of synthesized materials as adsorbent for organic compound are discussed. The results show that there are several factors that influence the synthesis. When water content in gel increases, crystal size of NaX increases sharply. The increase of alkaline and silica contents increases the crystallinity and decreases the particle size of nano NaX, and the particle size reaches the minimum at Na 2 O/Al 2 O 3 = 5.0 and SiO 2 /Al 2 O 3 = 4.0. Crystal sizes formed at low crystallizing temperature are smaller than those formed at higher temperature. Ageing time and crystallizing time strongly influence the crystallinity and crystal size, which is related to the number of crystal seeds formed during ageing period, the growth of seed and the partial solubility of crystal at maximum formation. Nano NaX was characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET) adsorption, Fourier transform infrared (FTIR) and simultaneous thermogravimetry–differential scanning calorimetry (TG/DSC). At optimized synthesis conditions, nano NaX has surface area of 573 m 2 g −1 with external surface area of 92 m 2 g −1 , pore size distribution at 0.81 and 10.8 nm, average crystal size of 25 nm and thermal stability up to 789 °C. This material can adsorb cumene rapidly with high adsorption capacity and stability. (paper)

Synthesis and dosimetric characterization of LiF-MgF2, doped with Lu

International Nuclear Information System (INIS)

Gonzalez, Pedro R.; Nieto, Ana L.; Cruz-Zaragoza, Epifanio; Furetta, Claudio

2013-01-01

The results of the synthesis and characterization of dosimetric thermoluminescent material based on the composition LiF-MgF 2 1:1 (Z eff = 9.7) doped Lu 3+ ions, developed at the National Institute of Nuclear Research, Mexico are presented. The TL material synthesis was carried out using the technique of casting solid substances, preparations were made with dopant concentrations of 0.25, 0.83, 1.00 and 2.00 mol%, the 1 mol% resulted in increased sensitivity to radiation. Its brightness curve has the TL peak intensity at 330 deg C when irradiated to 1000 Gy, whereas when irradiated greater than 2500 Gy, occurs at 230 ° C, also has a peak of smaller maximum intensity at 140 ° C. Microstructural characterization of the obtained material was performed using the techniques of scanning electron microscopy and X-ray diffraction Kinetic parameters of the curves of brightness of the material is performed by the deconvolution method using the sequential quadratic programming algorithm, developed in the same institute. This new TL material complies fully with international standards to be used as dosimetry system in medical physics, research and industry, as its TL response (total integrated under the curve) to 60 Co gamma radiation, presents linearity between 1 and 5000 Gy , while the response of commercial TLD dosimeter-100 used as a reference, is only linear up to 10 Gy

Electrospun V2O5 composite fibers: Synthesis, characterization and ammonia sensing properties

International Nuclear Information System (INIS)

Modafferi, V.; Trocino, S.; Donato, A.; Panzera, G.; Neri, G.

2013-01-01

In the present work, vanadium oxide (V 2 O 5 ) fibers have been investigated for monitoring ammonia (NH 3 ) at ppb levels in air. A simple sol gel-based electrospinning process has been applied for the synthesis of vanadium oxide/polyvinyl acetate (PVAc) and vanadium oxide/polyvinylpyrrolidone (PVP) composite fibers. Composite fibers doped with platinum (Pt) have been also prepared. The pure and Pt-doped metal oxide phase has been subsequently obtained by removing the polymer binder at high temperature in air. The samples have been widely studied to characterize their morphological and microstructural properties by X-Ray Diffraction, Fourier Transform InfraRed spectroscopy, X-ray Photoelectron Spectroscopy, and Scanning Electron Microscopy investigations. The application of the produced fibers in highly sensitive ammonia resistive sensors has been demonstrated. The influence of the nature of polymer binder and platinum addition on the sensing performances of the V 2 O 5 fibers has been investigated and discussed.V 2 O 5 fibers produced by using PVP as a polymer binder have shown higher sensitivity toward ammonia at ppb concentrations than fibers obtained with PVAc. Pt-doped samples have shown a lower response compared to un-doped samples. - Highlights: • Synthesis of vanadium oxide composite fibers by electrospinning • Physical and chemical characterization of prepared samples • Investigation of the sensing properties to ppb concentrations of ammonia in air

Synthesis and thermoluminescent characterization of LiF doped with Ag; Sintesis y caracterizacion termoluminiscente de LiF dopado con Ag

Energy Technology Data Exchange (ETDEWEB)

Encarnacion, E. K.; Reyes, J.; Guerrero, Z. [Universidad Autonoma de Santo Domingo, Facultad de Ciencias, Ciudad Universitaria, Santo Domingo (Dominican Republic); Sosa, M. A.; Vallejo, M. A.; Rivera P, E., E-mail: emma.kee@gmail.com [Universidad de Guanajuato, Campus Leon, Division de Ciencias e Ingenierias, Loma del Bosque 103, Col. Lomas del Campestre, 37150 Leon, Guanajuato (Mexico)

2015-10-15

Full text: In this paper the synthesis and characterization of lithium fluoride (LiF) crystals pure and activated with silver (Ag) is reported. The synthesis was carried out by the method of co-precipitation; three samples were obtained one of pure LiF and two were activated with 0.02 and 0.04% of Ag. All samples were subjected to X-ray emission and the results were analyzed. The synthesized samples were characterized by X-ray diffraction, thermoluminescence and X-ray fluorescence. The XRD results show complete crystal structures. The radiation dosimetry responses are discussed. These are the first results of a research conducted at the Universidad Autonoma de Santo Domingo in collaboration with the Universidad de Guanajuato. (Author)

Synthesis and characterization of TiO2 nanoparticles by the method Pechini

International Nuclear Information System (INIS)

Zoccal, Joao Victor Marques; Arouca, Fabio de Oliveira; Goncalves, Jose Antonio Silveira

2009-01-01

In recent years, scientific research showed an increasing interest in the field of nanotechnology, resulting in several techniques for the production of nanoparticles, such as methods of chemical synthesis. Among the various existing methods, the Pechini method has been used to obtain nanoparticles of titanium dioxide (TiO 2 ). Thus, this work aims to synthesize and characterize nanoparticles of TiO 2 obtained by this method. The technique constitutes in the reaction between citric acid with titanium isopropoxide, resulting as the product the titanium citrate. With the addition of the ethylene glycol polymerization occurs, resulting in a polymeric resin. At the end of the process, the resin is calcined to remove organic matter, creating nanoparticles of TiO 2 . The resulting powders were characterized by thermogravimetric analysis (TGA) and thermal differential analysis (DTA), X-ray diffraction, absorption spectrophotometry in the infrared, method of adsorption nitrogen / helium (BET method) and scanning electron microscopy. The results obtained in the characterization techniques showed that the Pechini method is promising in obtaining nanosized TiO 2 . (author)

Synthesis and characterization of ceramic powders of pure and doped with trivalent erbium barium tungstate

International Nuclear Information System (INIS)

Sousa, R.B. de; Nascimento, V.A. do; Matos, J. M.E. de; Santos, M.R.M.C.

2014-01-01

This research proposes the synthesis and characterization of pure and doped with Er"3"+ (1 and 2 %) barium tungstate powders prepared by the coprecipitation method. In order to characterize the obtained powders were used X-Ray Diffractometry, Raman Spectroscopy and Fourier Transform Infrared Spectroscopy. According to the standard XRD spectra, the crystals exhibited the presence of tetragonal scheelite structure without the presence of secondary phases. Raman spectra showed the presence of eleven vibrational modes and two modes were observed in the infrared spectra. The synthesized oxides showed good crystallinity and structurally ordered at short and long-range. (author)

Synthesis and characterization of organic-inorganic hybrids formed between conducting polymers and crystalline antimonic acid

Directory of Open Access Journals (Sweden)

Beleze Fábio A.

2001-01-01

Full Text Available In this paper we report the synthesis and characterization of novel organic-inorganic hybrid materials between the crystalline antimonic acid (CAA and two conductive polymers: polypyrrole and polyaniline. The hybrids were obtained by in situ oxidative polymerization of monomers by the Sb(V present in the pyrochlore-like CAA structure. The materials were characterized by infrared and Raman spectroscopy, X-ray diffraction, cyclic voltammetry, CHN elemental analysis and electronic paramagnetic resonance spectroscopy. The results showed that both polymers were formed in their oxidized form, with the CAA structure acting as a counter anion.

Synthesis, characterization and wound healing imitation of Fe3O4 magnetic nanoparticle grafted by natural products

Science.gov (United States)

Pala, Sravan Kumar

This research focused on the study of the core-shelled magnetic nanomaterials derived from a colloidal chemistry. The goals are four-fold: (1) synthesis of Fe3O4MNMs using colloidal chemistry. The Fe 3O4 MNMs were then grafted with extracts derived from natural products, namely Olecraceavar italica (broccoli), Boletus edulis (mushroom)and Solanum lycopersicum (tomato);(2)characterization of natural products by chromatography and mass spectrometry;(3) characterization of MNMs to determine their crystallinity, morphological and elemental composition by the state-of-the-art instruments; and (4) biological evaluation using Gram-negative and Gram-positive bacteria. The approach provides advantages to precisely control the composition and homogeneity. The second advantage of the colloidal chemistry is its user friendliness and feasibility. Due to the nature of the natural products, the compatibility of MNM is anticipated to be enhanced.In this chapter, the nanomaterials will be discussed from four perspectives,§1.1 Nanotechnology (§1.1), §1.2 Synthesis of nanomaterials; §1.3 The natural product extract,; §1.4 Characterization of nanomaterials; and §1.5Biological application of nanomaterials.Fig. 1 summarized the overarching goals of this study.

Bio-assisted synthesis and characterization of nanostructured bismuth (III) sulphide using Clostridium acetobutylicum

International Nuclear Information System (INIS)

Kamaraj, Sathish Kumar; Venkatachalam, Ganesh; Arumugam, Palaniappan; Berchmans, Sheela

2014-01-01

Nanostructured bismuth (III) sulphide is synthesized at room temperature using a hydrogen sulphide producing microorganism namely Clostridium acetobutylicum. On contrary to chemical routes involving both the high and room temperature methods, the present experimental procedure involves a bio-assisted approach. This method is free from the usage of toxic and hazardous chemicals making it an environment friendly route. The synthesized bismuth sulphide is characterized using transmission electron microscope (TEM), powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). From our experiments we find that bismuth sulphide produced using this bio-assisted approach exhibits a hexagonal shaped plate-like structures and is stabilized by the extracellular proteins present in the culture medium. - Graphical abstract: A green chemistry approach towards the synthesis of bismuth (III) sulphide nanostructures at room temperature using a hydrogen sulphide producing microorganism namely, Clostridium acetobutylicum is demonstrated. - Highlights: • Environmentally benign (greener) route towards synthesis of Bi 2 S 3 nanostructures. • Bio-assisted synthesis of Bi 2 S 3 at room temperature using Clostridium acetobutylicum. • Extracellular proteins in H 2 S producing microorganism as stabilizer for Bi 2 S 3 NPs. • Hexagonal platelets of Bi 2 S 3 possessing an orthorhombic crystalline structure

Hybrid microwave synthesis and characterization of the compounds in the Li-Ti-O system

Energy Technology Data Exchange (ETDEWEB)

Yang, Li Hong; Dong, Cheng; Guo, Juan [National Laboratory for Superconductivity, Institute of Physics and Beijing National Laboratory for Condensed Matter Physics, Chinese Academy of Science, P.O. Box 603, Beijing 100080 (China)

2008-01-03

Hybrid microwave synthesis has been applied for preparation of Li{sub 4}Ti{sub 5}O{sub 12}, Li{sub 2}Ti{sub 3}O{sub 7}, Li{sub 2}TiO{sub 3} and LiTiO{sub 2} for the first time. Stepwise heating was used for avoiding the instantaneous release of gas by-product and obtaining well-shaped samples. The samples were characterized by powder X-ray diffraction, energy-dispersive X-ray analysis and scanning electron microscopy. The obtained samples have relatively uniform particle sizes. The electrochemical performance of Li{sub 4}Ti{sub 5}O{sub 12} and Li{sub 2}Ti{sub 3}O{sub 7} were investigated. The first discharge capacity of Li{sub 4}Ti{sub 5}O{sub 12} was 150 mAh g{sup -1} and 141 mAh g{sup -1} after 27 cycles and a very flat discharge and charge curve of Li{sub 4}Ti{sub 5}O{sub 12} was shown at about 1.56 V. Similarly, Li{sub 2}Ti{sub 3}O{sub 7} exhibits good cycle performance. The initial discharge capacity is 118 mAh g{sup -1} and 30th cycle is still 112 mAh g{sup -1}. (author)

Study on the Synthesis and Characterization of Nano Silver Loaded ZSM-5 Zeolite for Bacterial Elimination.

Science.gov (United States)

Nam, Le Thi Hoai; Vinh, Tran Quang; Loan, Nguyen Thi Thanh; Nhiem, Nguyen Thi; Trang, Nguyen Thi Thu; Tan, Nguyen Minh; Radnik, Jörg

2015-09-01

The synthesis of nano silver coated ZSM-5 zeolite (Ag/ZSM-5) by ion exchange method combined with anaerobic thermal treatment and its bacterial elimination performance were studied. The various Ag content of different samples was analysed by atomic absorption spectroscopy method. The Ag/ZSM-5 sample with 0.251 wt% Ag (denoted as ZAg3) was characterized by using atomic absorption spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and pulsed CO chemisorption methods. The results showed that silver nanoparticles with a small nano-size of 2-3 nm were formed and distributed on the surface of ZSM-5 zeolite with a dispersion value of 59%. The samples denoted as ZAg1, ZAg2, ZAg3, ZAg4 correspond to a Ag content of 0.064; 0.128; 0.251; 0.253 wt% Ag. In the evaluation series, after 10 min of contact time between bacterial and Ag/ZSM-5, over 99% of E.coli (initial concentration was 10(6) cfu/ml) could be eliminated by Ag/ZSM-5 with the Ag content of at least 0.251 wt% (ZAg3). In addition, over 99% of Coliform (initial concentration was 10(5) cfu/ml) could be eliminated by Ag/ZSM-5 with Ag content of at least 0.128 wt% (ZAg2). In a further evaluation series varying the contact time, ZAg3 sample could eliminate over 99% and 100% of Ecoli after 10 min and 60 min, respectively (initial concentrations of both E.coli and Coliform were 10(5) cfu/ml). In addition, it could eliminate 100% of Coliform in only 10 min of contact time.

Selective synthesis and characterization of chlorins as sensitizers for photodynamic therapy

Science.gov (United States)

Montforts, Franz-Peter; Kusch, Dirk; Hoper, Frank; Braun, Stefan; Gerlach, Benjamin; Brauer, Hans-Dieter; Schermann, Guido; Moser, Joerg G.

1996-04-01

Chlorin type sensitizers have ideal photophysical properties for an application in PDT. The basic chlorin framework of these sensitizers has to be modified by attachment of lipophilic and hydrophilic residues to achieve a good cell uptake and tumor enrichment. In the present study we describe the selective synthesis of amphiphilic chlorins starting from the readily accessible red blood pigment heme. The photophysical properties of the well defined synthetic chlorins are characterized by photophysical investigations. The kinetic of cell uptake, the localization in the cell and the photodynamic behavior of the amphiphilic sensitizers are demonstrated by incubation of A 375 cancer cell lines with structurally different chlorins.

Synthesis and characterization of semi-IPNs based on PVP and PLLA

International Nuclear Information System (INIS)

Camilo, A.P.R.; Mano, V.; Felisberti, M.I.

2010-01-01

The specific interest in the synthesis of semi-IPNs based on PLLA and PVP homopolymers due to the fact these are biodegradable and biocompatible, which allows us to infer applications in the medical field as sutures, implants, matrices for controlled release of drugs etc. The objective was to prepare a multicomponent material amphiphile in the form of semi-interpenetrating polymer networks, based on poly (L-lactide), PLLA, hydrophobic homopolymer, and poly (vinylpyrrolidone), PVP, hydrophilic component. The preparation of semi-IPN combined the polymerization and crosslinking of N-vinylpyrrolidone in the presence of poly (L-lactide). The products were characterized by spectroscopic and thermal methods. (author)

Exploring the Fundamentals of Microreactor Technology with Multidisciplinary Lab Experiments Combining the Synthesis and Characterization of Inorganic Nanoparticles

Science.gov (United States)

Emmanuel, Noemie; Emonds-Alt, Gauthier; Lismont, Marjorie; Eppe, Gauthier; Monbaliu, Jean-Christophe M.

2017-01-01

Multidisciplinary lab experiments combining microfluidics, nanoparticle synthesis, and characterization are presented. These experiments rely on the implementation of affordable yet efficient microfluidic setups based on perfluoroalkoxyalkane (PFA) capillary coils and standard HPLC connectors in upper undergraduate chemistry laboratories.…

Synthesis, characterization and applications of graphene architectures

Science.gov (United States)

Thomas, Abhay Varghese

Graphene, a two--dimensional sheet of sp2 hybridized carbon atoms arranged in a honeycomb lattice structure, has garnered tremendous interest from the scientific community for its unique combination of properties. It has interesting electrical, thermal, optical and mechanical properties that scientists and engineers are trying to understand and harness to improve current products as well as focus on disruptive technologies that can be made possible by this next generation material. In this thesis the synthesis, characterization and applications of various graphene architectures were explored from the context of a bottom--up and top--down synthesis approach. The work is divided into three main chapters and each one deals with a unique architecture of graphene as well as its properties and an application to a real world problem. In Chapter 2, we focus on bottom--up synthesis of graphene sheets by chemical vapor deposition. We then studied the wetting properties of graphene coated surfaces. More specifically the wetting properties of single and multilayer graphene films on flat and nanoscale rough surfaces are explored and the insights gained are used in improving heat transfer performance of copper surfaces. Single layer graphene, on certain flat surfaces, was shown to exhibit `wetting transparency' as a result of its sheer thinness and this property is of interest in various wetting related applications. Surface protection from corrosion and/or oxidation without change in wetting properties is tremendously useful in multiple fields and we looked to apply this property to dehumidification of copper surfaces. The short time scales results demonstrated that graphene indeed served to prevent oxidation of the surface which in turn promoted increased heat transfer co--efficients with respect to the oxidized copper surfaces. Closer inspection of the surface over long time scales however revealed that the oxide layer changed the wetting properties and this was detrimental

SYNTHESIS AND CHARACTERIZATION OF NEW STABILIZERS WITH OPTIMAL MOLECULAR WEIGHT

Institute of Scientific and Technical Information of China (English)

Jiang-qing Pan

2001-01-01

Over 2 × l08 tons of polymers are produced every year, and a large portion of polymers faces the degradation problem. There are many effective methods to protect polymers against degradation and the addition of stabilizers to polymer remains the most convenient and effective way of enhancing polymer life and performance. In this article, a series of effective stabilizers with optimal molecular weight (MW), including common, monomeric and polymeric stabilizers (antioxidant and light stabilizer) were synthesized using isocyanation, controlled isocyanation, hydrosilylation, epoxide addition, macroreaction of stabilizing functional compounds and polymerization of monomeric stabilizers. The sructure and performance of these new stabilizers were characterized by using IR, NMR, MS, UV-spectra, XPS and elemental analysis. The current development of stabilizer synthesis was also reviewed.``

Synthesis and Characterization of High-Dielectric-Constant Nanographite-Polyurethane Composite

Science.gov (United States)

Mishra, Praveen; Bhat, Badekai Ramachandra; Bhattacharya, B.; Mehra, R. M.

2018-05-01

In the face of ever-growing demand for capacitors and energy storage devices, development of high-dielectric-constant materials is of paramount importance. Among various dielectric materials available, polymer dielectrics are preferred for their good processability. We report herein synthesis and characterization of nanographite-polyurethane composite with high dielectric constant. Nanographite showed good dispersibility in the polyurethane matrix. The thermosetting nature of polyurethane gives the composite the ability to withstand higher temperature without melting. The resultant composite was studied for its dielectric constant (ɛ) as a function of frequency. The composite exhibited logarithmic variation of ɛ from 3000 at 100 Hz to 225 at 60 kHz. The material also exhibited stable dissipation factor (tan δ) across the applied frequencies, suggesting its ability to resist current leakage.

Synthesis, stability range and characterization of Pr2Cu2O5

Science.gov (United States)

Fernández-Sanjulián, Javier; Morán, Emilio; Ángel Alario-Franco, Miguel

2010-03-01

A novel Pr2Cu2O5 phase has been prepared under high-pressure and high-temperature conditions (P ∼6 GPa and T ∼1673 K) in a Belt-type apparatus and characterized by X-ray diffraction and electron microscopy. The crystal structure appears to be an orthorhombic "oxygen-deficient perovskite" (M.T. Anderson, J.T. Vaughey, and K.R. Poeppelmeier, Structural similarities among oxygen-deficient perovskites, Chem. Mater. 5 (1993), pp. 151-165) isostructural with La2Cu2O5 (J.F. Bringley, B.A. Scott, S.J. La Placa, R.F. Boheme, T.M. Shaw, M.W. McElfresh, S.S. Trail, and D.E. Cox, Synthesis of the defect perovskite series LaCuO 3-δ with copper valence varying from 2+to 3+, Nature 347 (1990), pp. 263-265) and Nd2Cu2O5 (B.-H. Chen, D. Walker, E. Suard, B.A. Scott, B. Mercey, M. Hervieu, and B. Raveau, High pressure synthesis of NdCuO3-δ perovskites (0≤δ≤0.5). Inorg. Chem. 34 (1995), pp. 2077-2083).

Synthesis and characterization of binder-free Cr3C2 coatings on nickel-based alloys for molten fluoride salt corrosion resistance

International Nuclear Information System (INIS)

Brupbacher, Michael C.; Zhang, Dajie; Buchta, William M.; Graybeal, Mark L.; Rhim, Yo-Rhin; Nagle, Dennis C.; Spicer, James B.

2015-01-01

Under various conditions, chromium carbides appear to be relatively stable in the presence of molten fluoride salts and this suggests that their use in corrosion resistant coatings for fluoride salt environments could be beneficial. One method for producing these coatings is the carburization of sprayed Cr coatings using methane-containing gaseous precursors. This process has been investigated for the synthesis of binder-free chromium carbide coatings on nickel-based alloy substrates for molten fluoride salt corrosion resistance. The effects of the carburization process on coating microstructure have been characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM) in conjunction with energy dispersive spectroscopy (EDS). Both plasma-sprayed and cold-sprayed Cr coatings have been successfully converted to Cr 3 C 2 , with the mechanism of conversion being strongly influenced by the initial porosity in the as-deposited coatings

Synthesis and characterization of bulk Cu2ZnSnX4 (X: S, Se) via thermodynamically supported mechano-chemical process

International Nuclear Information System (INIS)

Pareek, Devendra; Balasubramaniam, K.R.; Sharma, Pratibha

2015-01-01

Materials with the general formula, Cu 2 ZnSnX 4 (CZTX; X: Group 16 elements), with X being S/Se, have been receiving considerable attention due to their utility as an absorber layer in solar photovoltaics (PV). This paper reports on the synthesis of CZTSe and CZTS nanocrystalline powders at low temperatures, starting from elemental metal and chalcogen powders, via the low cost, scalable technique of ball milling. The prepared samples were well characterized using the different characterization tools. XRD, Raman, SEM and TEM studies confirm the formation of single-phase, stoichiometric, nano-crystalline kesterite CZTS and CZTSe powders. The low temperature phase selection of the complex quaternary compound in this system is seen as a direct consequence of the thermodynamic facilitation, coupled with the capability of mechano-chemical synthesis to aid in overcoming kinetic constraints. The optical bandgap of the various samples of CZTS was observed in the range of 1.4–1.6 eV and corresponding values for CZTSe was observed to be in the range of 1.08–1.18 eV. Our work provides a pathway for developing cheap, scalable, and ink-based techniques for low cost solar PV. - Graphical abstract: Display Omitted - Highlights: • A scalable route for synthesis of near phase pure CZTS/Se nano-crystals has been demonstrated. • Stoichiometric CZTS and CZTSe were synthesized via mechano-chemical synthesis route. • Synthesis at near room temperature is supported by thermodynamic calculations

Synthesis and characterization of poly iodine anilines by plasma

International Nuclear Information System (INIS)

Enriquez P, M.A.

2003-01-01

The polymers and organic materials present a numberless quantity of applications. However, it has not been but until recent times that it has been found that some of these materials can possess semiconductor properties. This has generated a great interest for the investigation in the area of semiconductor polymers. The poly aniline (Pan) it is one of the main semiconductor polymers because their electric properties change depending on the doping and of the state of oxidation to the one the molecules are subjected. The synthesis of this material has been carried out by means of chemical oxidation or electrochemistry. In this work a study is presented on the formation of poly aniline polymers with halogens chemically united to the aniline ring, poly(m-iodine aniline) (m-PAnI) and poly(m-chloroaniline) (m-PAnCI) for plasma. The plasma is generated by means of discharges of splendor with an r f amplifier to 13.5 MHz to drops pressures (10 -2 mbar). The synthesized polymers were obtained in form of thin film in the walls of the reactor and in the substrate introduced in the one. The electric properties of the polymers were evaluated in function of the time of reaction. Also, the conductivity of the polymers was compared synthesized in this work with reported data of synthesized poly aniline and doped with iodine for plasma. The highest values in conductivity are obtained in the poly aniline where the halogens are chemically connected to the ring that if it is doped with iodine. The atomic proportion in the surface of the polymers was analyzed by dispersive energy spectroscopy with which is deduced that the halogens come off of the molecules of the monomers or of the polymer in formation and that the atoms of iodine get lost more easily than those of chlorine. Other techniques that were used to characterize to the poly aniline were scanning electron microscopy, infrared spectroscopy, thermal gravimetric analysis and X-ray diffraction. The results are presented in

Characterization of Initial Parameter Information for Lifetime Prediction of Electronic Devices.

Science.gov (United States)

Li, Zhigang; Liu, Boying; Yuan, Mengxiong; Zhang, Feifei; Guo, Jiaqiang

2016-01-01

Newly manufactured electronic devices are subject to different levels of potential defects existing among the initial parameter information of the devices. In this study, a characterization of electromagnetic relays that were operated at their optimal performance with appropriate and steady parameter values was performed to estimate the levels of their potential defects and to develop a lifetime prediction model. First, the initial parameter information value and stability were quantified to measure the performance of the electronics. In particular, the values of the initial parameter information were estimated using the probability-weighted average method, whereas the stability of the parameter information was determined by using the difference between the extrema and end points of the fitting curves for the initial parameter information. Second, a lifetime prediction model for small-sized samples was proposed on the basis of both measures. Finally, a model for the relationship of the initial contact resistance and stability over the lifetime of the sampled electromagnetic relays was proposed and verified. A comparison of the actual and predicted lifetimes of the relays revealed a 15.4% relative error, indicating that the lifetime of electronic devices can be predicted based on their initial parameter information.

Characterization of Initial Parameter Information for Lifetime Prediction of Electronic Devices.

Directory of Open Access Journals (Sweden)

Zhigang Li

Full Text Available Newly manufactured electronic devices are subject to different levels of potential defects existing among the initial parameter information of the devices. In this study, a characterization of electromagnetic relays that were operated at their optimal performance with appropriate and steady parameter values was performed to estimate the levels of their potential defects and to develop a lifetime prediction model. First, the initial parameter information value and stability were quantified to measure the performance of the electronics. In particular, the values of the initial parameter information were estimated using the probability-weighted average method, whereas the stability of the parameter information was determined by using the difference between the extrema and end points of the fitting curves for the initial parameter information. Second, a lifetime prediction model for small-sized samples was proposed on the basis of both measures. Finally, a model for the relationship of the initial contact resistance and stability over the lifetime of the sampled electromagnetic relays was proposed and verified. A comparison of the actual and predicted lifetimes of the relays revealed a 15.4% relative error, indicating that the lifetime of electronic devices can be predicted based on their initial parameter information.

Synthesis and characterization of novel nanothermometers

Energy Technology Data Exchange (ETDEWEB)

Baumert, Delphine [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Larsen, George [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Coopersmith, Kaitlin [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Schyck, Sarah [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Murph, Simona [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-03-23

A straightforward approach was developed for the synthesis of Pd, Pd-Fe₂O₃, Au-Fe₂O₃, and Au-Pd-Fe₂O₃ nanothermometers, using a single SL DNA. These NP-DNA conjugates were characterized using techniques including EDX measurements, ζ-potential of NPs before and after DNA functionalization, electron microscopy studies and fluorescence spectroscopy. The fluorescence studies of the NP-DNA demonstrate the interaction between the NP and the fluorophore, which is quenched in the case of Au-Pd-Fe₂O₃ NPs and is perhaps enhanced (when compared to AuNPs) in the case of Pd and Pd-Fe₂O₃ NPs. In order to achieve more accurate and reproducible measurements, designing a system that is able to hold the NP-DNA conjugates at a temperature for a longer period of time to allow them to 12 equilibrate is currently underway. Our studies show that Au-Pd-Fe₂O₃ NPs are the best candidate material to serve as nanothermometers when compared to Pd, Pd-Fe₂O₃, and Au-Fe₂O₃ materials.

Synthesis, characterization, and application of novel biodegradable self-assembled 2-(N-phthalimido) ethyl-palmitate nanoparticles for cancer therapy

Science.gov (United States)

Kasoju, Naresh; Bora, Debajeet K.; Bhonde, Ramesh R.; Bora, Utpal

2010-03-01

We report the synthesis of novel biodegradable nanoparticles (NPs) which can kill the cancer cells without any additional drug loading. The NP was a self-assembled form of a phthalimide based conjugate, in which the phthalimide moiety was responsible for the anticancer activity. We describe the synthesis of a novel 2-(N-phthalimido) ethyl palmitate (PHEP-Pal) conjugate and subsequent preparation of NPs by a simple self assembly process. The successful synthesis of conjugate was confirmed by various characterization studies including nuclear magnetic resonance spectroscope, Fourier transform infrared spectroscope, TOF-liquid chromatography mass spectroscope, differential scanning calorimetry, and X-ray diffraction unit. The synthesis, shape, size, and size distribution of PHEP-Pal NPs were determined by transmission electron microscope, atomic force microscope, and dynamic light scattering technique. Finally, cell culture studies using A549 and HeLa cells were done to evaluate the anticancer effect of PHEP-Pal NPs, which demonstrated the potency of these NPs for use in cancer chemotherapy.

Synthesis and characterization of nano hydroxyapatite using reverse micro emulsions as nano reactors

International Nuclear Information System (INIS)

Amin, S.; Siddique, T.

2015-01-01

In the present work reverse micro emulsion has been employed as nano reactors to synthesize nano crystalline Hydroxyapatite (HA). Two precursors; calcium and phosphate with different counter ions of each were used for the synthesis of HA at two different temperatures. To maintain the emulsified nano reactor, cyclohexane, TX-100 and 1-butanol including phosphate precursor was the continuous phase while aqueous Ca precursor solution was taken as the dispersed phase. Nano crystalline particles thus produced were evaluated on the basis of synthesis route, counter ions and temperature. It has been shown that emulsified nano reactors control the morphology, particle size and minimize phase transformation of HA. Characterizations of nano powder of HA are carried out using x-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FTIR), and scanning electron microscopy (SEM). HA crystallite size was found to be in the range of 20-25 nm whereas the morphology of nano particles changed from spheres to rods. (author)

Synthesis and Photophysical Characterizations of Thermal -Stable Naphthalene Benzimidazoles

OpenAIRE

Erten Ela, Şule; Özçelik, Serdar; Eren, Ersin

2011-01-01

Microwave-assisted synthesis, photophysical and electrochemical properties of thermal-stable naphthalene benzimidazoles and naphthalimides are studied in this paper. Microwave-assisted synthesis of naphthalene benzimidazoles provide higher yields than the conventional thermal synthesis. Comparative photophysical properties of naphthalene benzimidazoles and naphthalimides are revealed that conjugation of electron-donating group onto naphthalimide moiety increases fluorescence ...

Mn(III)-initiated facile oxygenation of heterocyclic 1,3-dicarbonyl compounds.

Science.gov (United States)

Rahman, Md Taifur; Haque, Md Aminul; Igarashi, Hikaru; Nishino, Hiroshi

2011-11-16

The Mn(III)-initiated aerobic oxidation of heterocyclic 1,3-dicarbonyl compounds, such as 4-alkyl-1,2-diphenylpyrazolidine-3,5-diones, 1,3-dialkylpyrrolidine-2,4-diones, 3-alkyl-1,5-dimethylbarbituric acids, and 3-butyl-4-hydroxy-2-quinolinone gave excellent to good yields of the corresponding hydroperoxides, which were gradually degraded by exposure to the metal initiator after the reaction to afford the corresponding alcohols. The synthesis of 30 heterocyclic 1,3-dicarbonyl compounds, the corresponding hydroperoxides and the 10 alcohols, their characterization, and the limitations of the procedure are described. In addition, the mechanism of the hydroperoxidation and the redox decomposition of the hydroperoxides are discussed.

Biochemical characterization of a recombinant Japanese encephalitis virus RNA-dependent RNA polymerase

Directory of Open Access Journals (Sweden)

Kim Chan-Mi

2007-07-01

Full Text Available Abstract Background Japanese encephalitis virus (JEV NS5 is a viral nonstructural protein that carries both methyltransferase and RNA-dependent RNA polymerase (RdRp domains. It is a key component of the viral RNA replicase complex that presumably includes other viral nonstructural and cellular proteins. The biochemical properties of JEV NS5 have not been characterized due to the lack of a robust in vitro RdRp assay system, and the molecular mechanisms for the initiation of RNA synthesis by JEV NS5 remain to be elucidated. Results To characterize the biochemical properties of JEV RdRp, we expressed in Escherichia coli and purified an enzymatically active full-length recombinant JEV NS5 protein with a hexahistidine tag at the N-terminus. The purified NS5 protein, but not the mutant NS5 protein with an Ala substitution at the first Asp of the RdRp-conserved GDD motif, exhibited template- and primer-dependent RNA synthesis activity using a poly(A RNA template. The NS5 protein was able to use both plus- and minus-strand 3'-untranslated regions of the JEV genome as templates in the absence of a primer, with the latter RNA being a better template. Analysis of the RNA synthesis initiation site using the 3'-end 83 nucleotides of the JEV genome as a minimal RNA template revealed that the NS5 protein specifically initiates RNA synthesis from an internal site, U81, at the two nucleotides upstream of the 3'-end of the template. Conclusion As a first step toward the understanding of the molecular mechanisms for JEV RNA replication and ultimately for the in vitro reconstitution of viral RNA replicase complex, we for the first time established an in vitro JEV RdRp assay system with a functional full-length recombinant JEV NS5 protein and characterized the mechanisms of RNA synthesis from nonviral and viral RNA templates. The full-length recombinant JEV NS5 will be useful for the elucidation of the structure-function relationship of this enzyme and for the

Characterization of initial fluctuations for the hydrodynamical description of heavy ion collisions

CERN Document Server

Floerchinger, Stefan

2013-01-01

Event-by-event fluctuations in the initial conditions for a hydrodynamical description of heavy-ion collisions are characterized. We propose a Bessel-Fourier decomposition with respect to the azimuthal angle, the radius in the transverse plane and rapidity. This allows for a complete characterization of fluctuations in all hydrodynamical fields including energy density, pressure, fluid velocity, shear stress and bulk viscous pressure. It has the advantage that fluctuations can be ordered with respect to their wave length and that they can be propagated mode-by-mode within the hydrodynamical formalism. Event ensembles can then be characterized in terms of a functional probability distribution. For the event ensemble of a Monte Carlo Glauber model, we provide evidence that the latter is close to Gaussian form, thus allowing for a particularly simple characterization of the event distribution.

Synthesis and characterization of a new complex binuclear of binuclear of Pd(II) containing the antibiotic oxy tetracycline

International Nuclear Information System (INIS)

Guerra, Wendell; Fontes, Ana Paula Soares; Pereira-Maia, Elene Cristina

2010-01-01

This article reports the synthesis and characterization of a new binuclear complex of palladium (II) containing the antibiotic oxytetracycline. The complex was characterized by the usual techniques of analysis. With respect to sites of coordination, the IR spectral data suggests the involvement the oxygen of the amide group and the oxygen of the neighbor hydroxyl group at ring A and to the carbonyl oxygen at C11 and the hydroxyl group at C12. (author)

“Synthesis-on” and “synthesis-off” modes of carbon arc operation during synthesis of carbon nanotubes

International Nuclear Information System (INIS)

Yatom, Shurik; Selinsky, Rachel S.

2017-01-01

Arc discharge synthesis of single-walled carbon nanotubes (SWCNTs) remains largely uncontrollable, due to incomplete understanding of the synthetic process itself. Here, we show that synthesis of SWCNTs by a carbon arc may not constitute a single continuous process, but may instead consist of two distinct modes. One of these, a “synthesis-on” mode, produces the majority of the nanomaterials. During the synthesis-on mode, proportionally more carbon nanotubes are collected than in another mode, a “synthesis-off” mode. Both synthesis-on and synthesis-off modes for a typical arc configuration, employing a hollow anode filled with a mixture of powdered metal catalyst and graphite, were characterized by using in situ electrical, imaging, and spectroscopic diagnostics, along with ex situ imaging and spectroscopy. The synthesis-on mode duration is rare compared to the total arc run-time, helping to explain the poor selectivity found in the final collected products, a known inadequacy of arc synthesis. Finally, the rarity of the synthesis on mode occurence may be due to the synthesis off mode being more favorable energetically.

Incorporation of the zosteric sodium salt in silica nanocapsules: synthesis and characterization of new fillers for antifouling coatings

Science.gov (United States)

Ruggiero, Ludovica; Crociani, Laura; Zendri, Elisabetta; El Habra, Naida; Guerriero, Paolo

2018-05-01

In the last decade many commercial biocides were gradually banned for toxicity. This work reports, for the first time, the synthesis and characterization of silica nanocontainers loaded with a natural product antifoulant (NPA), the zosteric sodium salt which is a non-commercial and environmentally friendly product with natural origin. The synthesis approach is a single step dynamic self-assembly with tetraethoxysilane (TEOS) as silica precursor. Unlike conventional mesoporous silica nanoparticles, the structure of these silica nanocontainers provides loading capacity and allows prolonged release of biocide species. The obtained nanocapsules have been characterized morphologically by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The encapsulation was checked by FTIR ATR spectroscopy and thermogravimetric analyses. The results of the release studies show the great potential of the here presented newly developed nanofillers in all applications where a controlled release of non-toxic and environmentally friendly biocides is required.

Synthesis, Characterization, and Properties of the Two-Dimensional Chalcogenides: Monolayers, Alloys, and Heterostructures

Science.gov (United States)

Cain, Jeffrey D.

Inspired by the triumphs of graphene, and motivated by its limitations, the science and engineering community is rapidly exploring the landscape of other layered materials in their atomically-thin forms. Dominating this landscape are the layered chalcogenides; diverse in chemistry, crystal structure, and properties, there are well over 100 primary members of this material family. Driven by quantum confinement, single layers (or few, in some cases) of these materials exhibit electronic, optical, and mechanical properties that diverge dramatically from their bulk counterparts. While initially isolated in monolayer form via mechanical exfoliation, the field of two-dimensional (2D) materials is being forced evolve to more scalable and reliable methods. Focusing on the chalcogenides (e.g. MoS2, Bi 2Se3, etc.), this dissertation introduces and mechanistically examines multiple novel synthetic approaches for the direct growth of monolayers, heterostructures, and alloys with the desired quality, reproducibility and generality. The first methods described in this thesis are physical vapor transport (PVT) and evaporative thinning (ET): a facile, top-down synthesis approach for creating ultrathin specimens of layered materials down to the two-dimensional limit. Evaporative thinning, applied in this study to the fabrication of A2X3 (Bi2Se3 and Sb2Te3) monolayers, is based on the controlled evaporation of material from initially thick specimens until the 2D limit is reached. The resultant flakes are characterized with a suite of imaging and spectroscopic techniques and the mechanism of ET is investigated via in-situ heating within a transmission electron microscope. Additionally, the basic transport properties of the resultant flakes are probed. The growth of ultrathin GeSe flakes is explored using PVT and the material's basic structure, properties, and stability are addressed. Second, oxide precursor based chemical vapor deposition (CVD) is presented for the direct growth of

Synthesis and characterization of composites HoMn_1_-_x(Ni,Co)_xO_3

International Nuclear Information System (INIS)

Santos, Cassio Morilla dos

2011-01-01

In this work was accomplished the synthesis process and structural and magnetic characterization of HoMn_1_-_X(Ni,Co)_XO_3 compounds of perovskite structure. The samples synthesis were performed through modified polymeric precursor method. After synthesis and solvent removal, the polymer resin formed was treated at 350 deg C/4h for organic constituents removal, followed by heating treatment at 500 deg C/4h and 900 deg C/20h to obtain the crystalline phase. For structural characterization, it was used D10B-XPD beam line of Laboratorio Nacional de Luz Sincrotron (LNLS), where X-rays wavelengths below cobalt, manganese and nickel absorption edge, were used. The formation of HoNi_0_._5_0Mn_0_._5_0O_3, HoCo_0_._5_0Mn_0_._5_0O_3 and HoNi_0_._2_5Co_0_._2_5Mn_0_._5_0O_3 phases were observed by X-ray diffraction technique. By Rietveld refinement method for sample HoNi_0_._2_5Co_0_._2_5Mn_0_._5_0O_3, it was determined that cobalt and nickel had similar occupations at the top and bottom of unit cell, while the manganese preferentially occupied plan 002. The magnetic response of samples was studied through magnetization curves according to the temperature function and the applied magnetic field. The ZFC curves showed a paramagnetic response associated to holmium magnetic moment, and ferromagnetism, antiferromagnetism and ferrimagnetism coexistence, due to sublattices formed by transition metals. The FC curves evidenced the spin reversal phenomenon, associated to the interaction between the sublattice formed by transition metals with sublattices formed by rare-earth, considering a mechanism of antiferromagnetic exchange interaction. (author)

Synthesis and characterization of ferrous phosphate (vivianite) and its behavior in aqueous media

International Nuclear Information System (INIS)

Diaz F, J.C.

2003-01-01

The synthesis and characterization of materials that can be useful in Environmental Chemistry is very important because their characteristics are exposed and its behavior in chemical phenomena as the sorption in aqueous media is understand to use it in the human being benefit. With the object of using, in a future, the octa hydrated ferrous phosphate (vivianite) as a potential candidate for matrix confinement in contention walls for the storage of radioactive waste of long half life, it was synthesized and it characterized physico chemically and their properties of surface of this compound were evaluated. Presently work was carried out the synthesis and structural characterization of the iron phosphate II by infrared spectroscopy with having Fourier transform, high vacuum scanning electron microscopy, X-ray diffraction, thermal gravimetric analysis, the BET multipoint surface area and Moessbauer spectroscopy; as well as, the determination between aqueous media of the isoelectric point and the density of sites of surface of the compound. The octa hydrated ferrous phosphate was obtained pure. The results indicate that the product corresponds to the prospective mineral, the vivianite. The thermal gravimetric analysis demonstrated that the ferrous phosphate is a stable salt after the lost of water. The isoelectric point is since an important parameter because allows to know the behavior of the surface of the material in aqueous systems, in this case the isoelectric point, of the octa hydrated ferrous phosphate, in distilled water is of pH 4.20 and in solution of potassium nitrate 0.5 M is of pH = 3.75. This indicates that the material has an amphoteric surface depending on the pH. On the other hand, the density of active sites of surface obtained by titrations acid-base is of 20 sites by nm 2 . (Author)

Synthesis, Characterization, and Catalytic Applications of Transition Metal Oxide/Carbonate Nanomaterials

Science.gov (United States)

Jin, Lei

2011-12-01

This thesis contains two parts: 1) Studies of novel synthesis methods and characterization of advanced functional manganese oxide octahedral molecular sieves (OMS) and their applications in Li/Air batteries, solvent free toluene oxidations, and ethane oxydehydrogenation (ODH) in the presence of CO2, recycling the green house gas. 2) Development of unique Ln2O2CO3 (Ln = rare earth) layered materials and ZnO/La2O2CO3 composites as clean energy biofuel catalysts. These parts are separated into five different focused topics included in this thesis. The first topic presents studies of catalytic activities of a single step synthesized gamma-MnO2 octahedral molecular sieve nano fiber in solvent free atmospheric oxidation of toluene with molecular oxygen. Solvent free atmospheric oxidation of toluene is a notoriously difficult liquid phase oxidation process due to the challenge of oxidizing sp³ hybridized carbon in inactive hydrocarbons. The synthesized gamma-MnO2 showed excellent catalytic activity and good selectivity under the mild atmospheric reflux system. Under optimized conditions, a 47.8% conversion of toluene, along with 57% selectivity of benzoic acid and 15% of benzaldehyde were obtained. The effects of reaction time, amount of catalyst and initiator, and the reusability of the catalyst were investigated. The second topic involves developing titanium containing gamma-MnO 2 (TM) hollow spheres as electrocatalysts in Li/Air Batteries. Li/air batteries have recently attracted interest because they have the largest theoretical specific energy (11,972 Wh.kg-1) among all practical electrochemical couples. In this study, unique hollow aspheric materials were prepared for the first time using a one-step synthesis method and fully characterized by various techniques. These prepared materials were found to have excellent electrocatalytic activation as cathode materials in lithium-air batteries with a very high specific capacity (up to 2.3 A.h/g of carbon). The third

Synthesis and Ring-Opening Metathesis Polymerization of Second-Generation Dendronized Poly(ether Monomers Initiated by Ruthenium Carbenes

Directory of Open Access Journals (Sweden)

Guzmán Pablo E.

2016-03-01

Full Text Available The Ring-Opening Metathesis Polymerization (ROMP of second-generation dendronized monomers is described. Using the highly active and fast-initiating third-generation ruthenium complex [(H2IMes(pyr2Cl2RuCHPh], moderate to high molecular weight polymers (430-2230 kDa are efficiently synthesized with low dispersities (Ð = 1.01-1.17. This study highlights the power of the metathesis approach toward polymer synthesis in a context where monomer structure can significantly impede polymerization.

Synthesis and characterization of nanostructured titanium carbide for fuel cell applications

Energy Technology Data Exchange (ETDEWEB)

Singh, Paviter; Singh, Harwinder; Singh, Bikramjeet; Kaur, Manpreet; Kaur, Gurpreet; Kumar, Akshay, E-mail: akshaykumar.tiet@gmail.com [Advanced Functional Material Laboratory, Department of Nanotechnology,, Sri Guru Granth Sahib World University, Fatehgarh Sahib-140 406 Punjab (India); Kumar, Manjeet [Department of Materials Engineering, Defense Institute of Advanced Technology (DU), Pune-411 025 (India); Bala, Rajni [Department of Mathematics Punjabi University Patiala-147 002 Punjab (India)

2016-04-13

Titanium carbide (TiC) nanoparticles have been successfully synthesized by carbo-thermic reaction of titanium and acetone at 800 °C. This method is relatively low temperature synthesis route. It can be used for large scale production of TiC. The synthesized nanoparticles have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and differential thermal analyzer (DTA) techniques. XRD analysis confirmed the formation of single phase TiC. XRD analysis confirmed that the particles are spherical in shape with an average particle size of 13 nm. DTA analysis shows that the phase is stable upto 900 °C and the material can be used for high temperature applications.

Synthesis and Characterization of Calcium Phosphate Powders for Biomedical Applications by Plasma Spray Coating

OpenAIRE

Sasidharan Pillai, Rahul

2015-01-01

This PhD work mainly focus on the synthesis and characterization of calcium phosphate powders for plasma spray coating. The preparation of high temperature phase stabilized βTCP and HA/βTCP powders for plasma spray coating applications has been the topic of investigation. Nowadays plasma sprayed coatings are widely used for biomedical applications especially in the dental and orthopaedic implantation field. Previously Ti based alloys were widely used for the orthopaedic and dental implant ap...

Modified Polyacrylic Acid-Zinc Composites: Synthesis, Characterization and Biological Activity

Directory of Open Access Journals (Sweden)

Mohammed Rafi Shaik

2016-02-01

Full Text Available Polyacrylic acid (PAA is an important industrial chemical, which has been extensively applied in various fields, including for several biomedical purposes. In this study, we report the synthesis and modification of this polymer with various phenol imides, such as succinimide, phthalimide and 1,8-naphthalimide. The as-synthesized derivatives were used to prepare polymer metal composites by the reaction with Zn+2. These composites were characterized by using various techniques, including NMR, FT-IR, TGA, SEM and DSC. The as-prepared PAA-based composites were further evaluated for their anti-microbial properties against various pathogens, which include both Gram-positive and Gram-negative bacteria and different fungal strains. The synthesized composites have displayed considerable biocidal properties, ranging from mild to moderate activities against different strains tested.

CsPb2Br5 Single Crystals: Synthesis and Characterization

KAUST Repository

Dursun, Ibrahim

2017-08-02

CsPb2Br5 is a ternary halogen-plumbate material with close characteristics to well-reported halide perovskites. Due to its unconventional two-dimensional structure, CsPb2Br5 is being looked at broadly for potential applications in optoelectronics. CsPb2Br5 investigations are currently limited to nanostructures and powder forms of the material, which present unclear and conflicting optical properties. In this study, we present the synthesis and characterization of CsPb2Br5 bulk single crystals, which enabled us to finally clarify the material\\'s optical features. Our CsPb2Br5 crystal has a two-dimensional structure with Pb2Br5- layers spaced by Cs+ cations, and exhibits a ~3.1 eV indirect bandgap with no emission in the visible spectrum.

Synthesis and characterization of acrylate copolymer containing fluorescein functional group

International Nuclear Information System (INIS)

Hui, Guodong; Huang, Weiyun; Song, Yunzhao; Chen, Deben; Zhong, Anyong

2013-01-01

We report a novel method to fabricate fluorescent polymer (F-CPA) based on the esterification between acrylate copolymer (CPA) and fluorescein using N, N-dicyclohexylcarbodiimide (DCC)/4-dimethylaminopyridine (DMAP) as catalyst. The resulting copolymer was characterized by Fourier transform-infrared spectroscopy (FT-IR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), ultraviolet-visible spectroscopy (UV-Vis) and fluorescence spectroscopy. In addition, the influences of concentration, solvents, pH and metal cations (Cu"2"+, Fe"3"+ and Zn"2"+) on the fluorescent behaviors of F-CPA are discussed in detail. All those observations suggest that the synthesized F-CPA is an excellent luminescent macromolecular material with simple synthesis method and excellent solubility. Moreover, its sensitive fluorescence response behaviors to solvents, pH and metal cations make it to become a polymer-based probe

Synthesis, characterization and antibacterial property of ZnO:Mg nanoparticles

Science.gov (United States)

Kompany, A.; Madahi, P.; Shahtahmasbi, N.; Mashreghi, M.

2012-09-01

Sol-gel method was successfully used for the synthesis of ZnO nanoparticles (NPs) doped with different concentrations of Mg and the structural, optical and antibacterial properties of the nanoparticles were studied. The synthesized ZnO:Mg powders were characterized using x-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transformation Infrared (FTIR) and UV-Vis spectroscopy. It was revealed that the samples have hexagonal Wurtzite structure, and the phase segregation takes place for 15% Mg content. TEM images show that the average size of the particles is about 50 nm. Also, the antibacterial activities of the nanoparticles were tested against Escherichia coli (Gram negative) cultures. ZnO:Mg nanofluid showed good antibacterial activity which increases with the increase of NPs concentration, and decreases slightly with the amount of Mg.

Tuning of Recombinant Protein Expression in Escherichia coli by Manipulating Transcription, Translation Initiation Rates, and Incorporation of Noncanonical Amino Acids.

Science.gov (United States)

Schlesinger, Orr; Chemla, Yonatan; Heltberg, Mathias; Ozer, Eden; Marshall, Ryan; Noireaux, Vincent; Jensen, Mogens Høgh; Alfonta, Lital

2017-06-16

Protein synthesis in cells has been thoroughly investigated and characterized over the past 60 years. However, some fundamental issues remain unresolved, including the reasons for genetic code redundancy and codon bias. In this study, we changed the kinetics of the Eschrichia coli transcription and translation processes by mutating the promoter and ribosome binding domains and by using genetic code expansion. The results expose a counterintuitive phenomenon, whereby an increase in the initiation rates of transcription and translation lead to a decrease in protein expression. This effect can be rescued by introducing slow translating codons into the beginning of the gene, by shortening gene length or by reducing initiation rates. On the basis of the results, we developed a biophysical model, which suggests that the density of co-transcriptional-translation plays a role in bacterial protein synthesis. These findings indicate how cells use codon bias to tune translation speed and protein synthesis.

Green synthesis, characterization and antibacterial efficacy of palladium nanoparticles synthesized using Filicium decipiens leaf extract

Science.gov (United States)

Sharmila, G.; Farzana Fathima, M.; Haries, S.; Geetha, S.; Manoj Kumar, N.; Muthukumaran, C.

2017-06-01

Synthesis of metal nanoparticles through green chemistry route is an emerging eco-friendly approach in the present days. An eco-friendly, biogenic synthesis of palladium nanoparticles (PdNPs) using Filicium decipiens leaf extract was reported in the present study. The synthesized PdNPs were characterized by UV-visible spectroscopy, Transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The PdNPs formation was confirmed by UV-visible spectrophotometer and spherical shaped PdNPs with size range of 2-22 nm was observed in TEM analysis. Energy dispersive X-ray spectroscopy (EDS) analysis confirmed the presence of palladium in the synthesized nanoparticles. The crystalline nature of PdNPs was confirmed by XRD pattern and compared with the standard. The phytochemicals and proteins were identified by their functional groups in FT-IR spectrum and revealed the amide, amine groups present in F. decipiens may have involved in the bio-reduction reaction for PdNPs synthesis. Prepared PdNPs showed potential antibacterial activity against both Gram-positive and Gram-negative bacteria. F. decipiens leaf extract based PdNPs showed high bactericidal activity against Escherichia coli, Pseudomonas aeruginosa as compared to Staphylococcus aureus and Bacillus subtilis Results showed that phytochemicals rich F. decipiens leaf extract may be utilized as an effective non-toxic reducing agent for PdNPs synthesis and prepared PdNPs may useful in biomedical applications.

Ultrafiltration membranes from waste polyethylene terephthalate and additives: synthesis and characterization

Directory of Open Access Journals (Sweden)

Smitha Rajesh

2014-01-01

Full Text Available The synthesis and characterization of asymmetric ultrafiltration membranes from recycled polyethylene terephthalate (PET and polyvinylpyrrolidone (PVP is reported. PET is currently used in many applications, including the manufacture of bottles and tableware. Monomer extraction from waste PET is expensive, and this process has not yet been successfully demonstrated on a viable scale. Hence, any method to recycle or regenerate PET once it has been used is of significant importance from scientific and environmental research viewpoints. Such a process would be a green alternative due to reduced raw monomer consumption and the additional benefit of reduced manufacturing costs. The membranes described here were prepared by a phase-inversion process, which involved casting a solution containing PET, m-cresol as solvent, and polyethylene glycol (PEG of different molecular weights as additives. The membranes were characterized in terms of pure water permeability (PWP, molecular weight cut-off (MWCO, and flux and membrane morphology. The results show that the addition of PEG with high molecular weights leads to membranes with higher PWP. The presence of additives affects surface roughness and membrane morphology.

Low Temperature Solid-State Synthesis and Characterization of LaBO3

Directory of Open Access Journals (Sweden)

Azmi Seyhun KIPÇAK

2016-11-01

Full Text Available Rare earth (lanthanide series borates, possess high vacuum ultraviolet (VUV transparency, large electronic band gaps, chemical and environmental stability and exceptionally large optical damage thresholds and used in the development of plasma display panels (PDPs. In this study the synthesis of lanthanum borates via solid-state method is studied. For this purpose, lanthanum oxide (La2O3 and boric acid (H3BO3 are used for as lanthanum and boron sources, respectively. Different elemental molar ratios of La to B (between 3:1 to 1:6 as La2O3:H3BO3 were reacted by solid-state method at the reaction temperatures between 500°C - 700°C with the constant reaction time of 4 h. Following the synthesis, characterizations of the synthesized products are conducted by X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FT-IR, Raman spectroscopy and scanning electron microscope (SEM. From the results of the experiments, three types of lanthanum borates of; La3BO6, LaBO3 and La(BO23 were observed at different reaction parameters. Among these three types of lanthanum borates LaBO3 phase were obtained as a major phase.

Synthesis, characterization and antibacterial study on the chitosan-functionalized Ag nanoparticles.

Science.gov (United States)

Biao, Linhai; Tan, Shengnan; Wang, Yuanlin; Guo, Ximin; Fu, Yujie; Xu, Fengjie; Zu, Yuangang; Liu, Zhiguo

2017-07-01

This study provided a facile, one-step hydrothermal method to synthesize stable Ag colloid in aqueous solution by utilizing chitosan as both reductant and stabilizer. The formation of chitosan-functionalized Ag nanoparticles was verified by UV-Vis, FTIR, TEM, AFM and XRD measurements. FTIR results revealed that the primary amine groups and amide groups of chitosan have specific interactions with the surface of Ag nanoparticles. The average diameter of the Ag nanoparticles is 10.0±5.4nm as determined by TEM. Ag nanoparticles are highly crystalline as revealed by HR-TEM and XRD measurements. The size and shape of Ag nanoparticles are also found to depend on the pH condition in the synthesis. Ag nanoparticles were the main products at pH5.0 whereas large Ag nanotriangle and truncated triangular nanoplate were dominant at pH4.0 in the synthesis. Due to its monodispersity and good stability, the chitosan-functionalized Ag colloid synthesized at pH5.0 was further tested for its antibacterial activities against gram-positive bacteria, gram-negative bacteria and fungus. The results of zone of inhibition, inhibition ratio and SEM characterization revealed that chitosan-functionalized Ag nanoparticles have great bactericidal efficiency against both bacteria and fungus. Copyright © 2017 Elsevier B.V. All rights reserved.

In Situ Synchrotron X-Ray Diffraction Characterization of the Synthesis of Graphene Oxide and Reduced Graphene Oxide

DEFF Research Database (Denmark)

Storm, Mie Møller; Johnsen, Rune E.; Norby, Poul

2015-01-01

Graphene oxide (GO) and reduced graphene oxide (rGO) synthesised from GO, has a promising future in fields ranging from electronics to energy technologies[1]. GO may be synthesized by the modified Hummer’s method[2], where a mixture of potassium permanganate and concentrated sulfuric acid forms...... by placing a mixture of permanganate and sulphuric acid in a capillary next to graphite. The synthesis was then initiated by gently pushing the fluid mixture into the powder with N2 gas. The in situ XRD of the GO synthesis showed how the oxidation reaction proceeds in three separate stages, as seen in Figure...... 1. The first stage was the dissolution of potassium permanganate, followed by an intercalation stage and subsequent formation of crystalline material. The GO 001 diffraction peak was observed early during the synthesis, in the second stage, and the intensity of the 001 diffraction increased during...

Synthesis and characterization of zirconium molybdates of 99 Mo/99m Tc generators

International Nuclear Information System (INIS)

Contreras R, A.; Monroy G, F.; Diaz A, L.V.

2002-01-01

The zirconium molybdates are gels which are used as cation exchangers in the production of 99 Mo/ 99m Tc generators. The synthesis method and the characterization of these gels by thermogravimetry, infrared spectroscopy and X-ray diffraction is presented with the purpose of finding which the factors are that influence in the efficiency of the 99m Tc production. The results show that the quantity of molecular water contained in gel, is possibly the cause of variations of the efficiencies of the 99 Mo/ 99m Tc generator. (Author)

Synthesis of Cyclic Polymers and Characterization of Their Diffusive Motion in the Melt State at the Single Molecule Level

KAUST Repository

Habuchi, Satoshi; Yamamoto, Takuya; Tezuka, Yasuyuki

2016-01-01

We demonstrate a method for the synthesis of cyclic polymers and a protocol for characterizing their diffusive motion in a melt state at the single molecule level. An electrostatic self-assembly and covalent fixation (ESA-CF) process is used

Synthesis and characterization of a binary oxide ZrO2–TiO2 and its ...

Indian Academy of Sciences (India)

Administrator

Synthesis and characterization of a binary oxide ZrO2–TiO2 and its application in ... Solar cells based on dye-sensitized TiO2 nanoparticles were first developed by Grätzel ... cells, resulting in high Jsc (short-circuit current density),. *Author for .... simple method to study dye sensitization of semiconduc- tors. It is found that the ...

Synthesis and characterization of optical and electrical composite hybrid PVAl/CdS

International Nuclear Information System (INIS)

Oliveira, M.S.; Aquino, H.A.

2010-01-01

Aiming to develop new hybrid nanocomposite materials that present the physical properties of both components which allows to be applied in a variety of areas of nanotechnology among them in photonics, optoelectronics and sensor. The hybrid organic / inorganic PVAl / CdS is compound of a polymer matrix the polyvinyl alcohol (PVAl) and phase second cadmium sulfide (CdS), the synthesis was to did using the 'hydrothermal method' with five different concentrations of CdS between 0.05 and 0.7% (w/w). The hybrid solution obtained is to put sth down on glass substrate by the method 'Casting' so we get films with thicknesses ranging from 20 and 150 μm. The morphology of the films was characterized by X ray diffraction (DRX) and ultraviolet-visible spectroscopy (UV-vis). And the influence of CdS on the dielectric behavior in the films of PVAl / CdS, as dielectric relaxation (relaxation frequencies) were characterized by impedance spectroscopy. (author)

Synthesis and characterization of cationic lipid coated magnetic nanoparticles using multiple emulsions as microreactors

Energy Technology Data Exchange (ETDEWEB)

Akbaba, Hasan; Karagöz, Uğur [Ege University, Faculty of Pharmacy, Department of Pharmaceutical Biotechnology, 35100 Izmir (Turkey); Selamet, Yusuf [Izmir Institute of Technology, Faculty of Science, Department of Physics, 35433 Izmir (Turkey); Kantarcı, A. Gülten, E-mail: gulten.kantarci@ege.edu.tr [Ege University, Faculty of Pharmacy, Department of Pharmaceutical Biotechnology, 35100 Izmir (Turkey)

2017-03-15

The aim of this study was to develop a novel iron oxide nanoparticle synthesis method with in-situ surface coating. For this purpose multiple emulsions were used as microreactors for the first time and magnetic iron oxide particles synthesized in the core of cationic solid lipid nanoparticles. DLS, SEM, TEM, VSM, Raman Spectrometer, XRD, and XPS techniques were performed for characterization of the magnetic nanoparticles. Obtained magnetic nanoparticles are superparamagnetic and no additional process was needed for surface adjustments. They are positively charged as a result of cationic lipid coating and has appropriate particle size (<30 nm) for drug or nucleic acid delivery. Structure analysis showed that magnetic core material is in the form of magnetite. Saturation magnetization value was measured as 15–17 emu g{sup −1} for lipid coated magnetic nanoparticles obtained by multiple emulsion method which is reasonably sufficient for magnetic targeting. - Highlights: • A novel iron oxide nanoparticle synthesis method with in-situ surface coating. • Combining advantages of microemulsions and multiple emulsion methods. • Multiple emulsions were used as microreactors for magnetic nanoparticle synthesis. • Superparamagnetic iron oxide particles synthesized in the core of cationic lipids. • Possible delivery systems for nucleic acids, oil soluble compounds or drugs.

Synthesis and Characterization of Processable Polyaniline Salts

International Nuclear Information System (INIS)

Gul, Salma; Bilal, Salma; Shah, Anwar-ul-Haq Ali

2013-01-01

Polyaniline (PANI) is one of the most promising candidates for possible technological applications. PANI has potential applications in batteries, anion exchanger, tissue engineering, inhibition of steel corrosion, fuel cell, sensors and so on. However, its insolubility in common organic solvents limits its range of applications. In the present study an attempt has been made to synthesize soluble polyaniline salt via inverse polymerization pathway using benzoyl peroxide as oxidant and dodecylbenzenesulfonic acid (DBSA) as dopant as well as a surfactant. A mixture of chloroform and 2-butanol was used as dispersion medium for the first time. The influence of synthesis parameters such as concentration of aniline, benzoyl peroxide and DBSA on the yield and other properties of the resulting PANI salt was studied. The synthesized PANI salt was found to be completely soluble in DMSO, DMF, chloroform and in a mixture of toluene and 2-propanol. The synthesized polymer salt was also characterized with cyclic voltam-metry, SEM, XRD, UV-Vis spectroscopy and viscosity measurements. TGA was used to analyze the thermal properties of synthesized polymer. The extent of doping of the PANI salt was determined from UV-Vis spectra and TGA analysis. The activation energy for the degradation of the polymer was calculated with the help of TGA.

Green synthesis, characterization and catalytic activity of silver nanoparticles using Cassia auriculata flower extract separated fraction

Science.gov (United States)

Muthu, Karuppiah; Priya, Sethuraman

2017-05-01

Cassia auriculata L., the flower aqueous extract was fractionated by separating funnel using n-hexane (A1), chloroform (A2), ethyl acetate (A3) and triple distilled water (A4). The A4 fraction was concentrated and determined the presence of preliminary phytochemicals such as tannins, flavonoids, glycosides, carbohydrates and polyphenolic compounds. These phytochemical compounds acted as reducing as well as a stabilizing agent in the green synthesis of Ag NPs from aqueous silver ions. Initially, the colour change and UV-vis absorbance surface Plasmon resonance strong, wide band located at 435 nm has confirmed the synthesis of Ag NPs. The X-ray diffraction (XRD) pattern of Ag NPs shows a face-centered cubic crystal structure. The observed values were calculated by Debye-Scherrer equation to theoretical confirms the particle size of 18 nm. The surface morphology of Ag NPs was viewed by HRTEM, the particles are spherical and triangle shapes with sizes from 10 to 35 nm. Further, the Ag NPs was effective catalytic activity in the reduction of highly environmental polluted organic compounds of 4-nitrophenol and methyl orange. The green synthesis of Ag NPs seems to eco-friendly, cost-effective, conventional one spot synthesis and greater performance of catalytic degradation of environmentally polluted organic dyes.

Synthesis and characterization ligand tris-(2-thiosalicylamidoethyl)amine and its iron complexes and indium

International Nuclear Information System (INIS)

Guerra-Garcia, Pedro Pablo; Valle Bourrouet, Grettel

2006-01-01

The synthesis of coordination chemistry ligand tris-(2-tiosalicilamidoetil)amine is presented within the framework of study of tripod ligands, the corresponding complexes of iron and indium. Also, its spectroscopic characterization by proton magnetic resonance is showed; so the influence of ligand on a redox active metal and an inactive is compared. Electrochemical methods have been used. The presence of sulfur atoms modifies the redox and magnetic behavior of iron ion (III), as has been found in other similar ligands [es

Synthesis and characterization of CdS/PVA nanocomposite films

Science.gov (United States)

Wang, Hongmei; Fang, Pengfei; Chen, Zhe; Wang, Shaojie

2007-08-01

A series CdS/PVA nanocomposite films with different amount of Cd salt have been prepared by means of the in situ synthesis method via the reaction of Cd 2+-dispersed poly vinyl-alcohol (PVA) with H 2S. The as-prepared films were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) absorption, photoluminescence (PL) spectra, Fourier transform infrared spectroscope (FTIR) and thermogravimetric analysis (TGA). The XRD results indicated the formation of CdS nanoparticles with hexagonal phase in the PVA matrix. The primary FTIR spectra of CdS/PVA nanocomposite in different processing stages have been discussed. The vibrational absorption peak of Cd sbnd S bond at 405 cm -1 was observed, which further testified the generation of CdS nanoparticles. The TGA results showed incorporation of CdS nanoparticles significantly altered the thermal properties of PVA matrix. The photoluminescence and UV-vis spectroscopy revealed that the CdS/PVA films showed quantum confinement effect.

Synthesis and characterization of CdS/PVA nanocomposite films

International Nuclear Information System (INIS)

Wang Hongmei; Fang Pengfei; Chen Zhe; Wang Shaojie

2007-01-01

A series CdS/PVA nanocomposite films with different amount of Cd salt have been prepared by means of the in situ synthesis method via the reaction of Cd 2+ -dispersed poly vinyl-alcohol (PVA) with H 2 S. The as-prepared films were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) absorption, photoluminescence (PL) spectra, Fourier transform infrared spectroscope (FTIR) and thermogravimetric analysis (TGA). The XRD results indicated the formation of CdS nanoparticles with hexagonal phase in the PVA matrix. The primary FTIR spectra of CdS/PVA nanocomposite in different processing stages have been discussed. The vibrational absorption peak of Cd-S bond at 405 cm -1 was observed, which further testified the generation of CdS nanoparticles. The TGA results showed incorporation of CdS nanoparticles significantly altered the thermal properties of PVA matrix. The photoluminescence and UV-vis spectroscopy revealed that the CdS/PVA films showed quantum confinement effect

Mn(III-Initiated Facile Oxygenation of Heterocyclic 1,3-Dicarbonyl Compounds

Directory of Open Access Journals (Sweden)

Md. Aminul Haque

2011-11-01

Full Text Available The Mn(III-initiated aerobic oxidation of heterocyclic 1,3-dicarbonyl compounds, such as 4-alkyl-1,2-diphenylpyrazolidine-3,5-diones, 1,3-dialkylpyrrolidine-2,4-diones, 3-alkyl-1,5-dimethylbarbituric acids, and 3-butyl-4-hydroxy-2-quinolinone gave excellent to good yields of the corresponding hydroperoxides, which were gradually degraded by exposure to the metal initiator after the reaction to afford the corresponding alcohols. The synthesis of 30 heterocyclic 1,3-dicarbonyl compounds, the corresponding hydroperoxides and the 10 alcohols, their characterization, and the limitations of the procedure are described. In addition, the mechanism of the hydroperoxidation and the redox decomposition of the hydroperoxides are discussed.

Nanoparticle synthesis of zinc peroxide: structural and morphological characterization for bactericidal applications

International Nuclear Information System (INIS)

Colonia, Roberto; Martinez, Vanessa C.; Solis, Jose L.; Gomez, Monica M.

2013-01-01

Zinc peroxide (ZnO 2 ) nanoparticles were synthesized by sol-gel technique. The chemicals used for the synthesis were zinc acetate di-hydrate (Zn(CH 3 COO) 2. 2H 2 O) and hydrogen peroxide (H 2 O 2 ) at 30 % in an aqueous solution with sonication. The structure of the ZnO 2 nanoparticles was characterized by X-ray diffraction. While the morphology and the cluster size were determined using scanning and transmission electron microscopy. For a preliminary evaluation of the bactericidal properties of the ZnO 2 , the material was exposed to Staphylococcus aureus, Escherichia coli y Bacillus subtili, and the nanoparticles presented good bactericidal properties. (author)

Design, synthesis, and characterization of fluorine-free PAGs for 193-nm lithography

Science.gov (United States)

Liu, Sen; Glodde, Martin; Varanasi, Pushkara R.

2010-04-01

Photoacid generators (PAGs) are a key component in chemically amplified resists used in photolithography. Perfluorooctanesulfonates (PFOS) and other perfluoroalkylsulfonates (PFAS) have been well adopted as PAGs in 193 nm photoresist. Recently, concerns have been raised about their environmental impact due to their chemical persistency, bioaccumulation and toxicity. It is a general interest to find environmentally benign PAGs that are free of fluorine atoms. Here we describe the design, synthesis and characterization of a series of novel fluorine-free onium salts as PAGs for 193 nm photoresists. These PAGs demonstrated desirable physical and lithography properties when compared with PFAS-based PAGs for both dry and immersion exposures.

Synthesis, Characterization, and Computational Modeling of N-(1-Ethoxyvinylpyridinium Triflates, an Unusual Class of Pyridinium Salts

Directory of Open Access Journals (Sweden)

Jonathan D. Shapiro

2018-02-01

Full Text Available N-Substituted pyridinium salts constitute one of the most valuable reagent classes in organic synthesis, due to their versatility and ease of use. Herein we report a preliminary synthesis and detailed structural analysis of several N-(1-ethoxyvinylpyridinium triflates, an unusual class of pyridinium salts with potentially broad use as a reagent in organic synthesis. Treatment of pyridines with trifluoromethane sulfonic acid and ethoxyacetylene generates stable, isolable adducts which have been extensively characterized, due to their novelty. Three-dimensional structural stability is perpetuated by an array of C–H•••O hydrogen bonds involving oxygen atoms from the –SO3 groups of the triflate anion, and hydrogen atoms from the aromatic ring and vinyl group of the pyridinium cation. Predictions from density functional theory calculations of the energy landscape for rotation about the exocyclic C–N bond of 2-chloro-1-(1-ethoxyvinylpyridine-1-ium trifluoromethanesulfonate (7 and 1-(1-ethoxyvinylpyridine-1-ium trifluoromethanesulfonate (16 are also reported. Notably, the predicted global energy minimum of 7 was nearly identical to that found within the crystal structure.

Combinatorial Strategies for Synthesis and Characterization of Alloy Microstructures over Large Compositional Ranges.

Science.gov (United States)

Li, Yanglin; Jensen, Katharine E; Liu, Yanhui; Liu, Jingbei; Gong, Pan; Scanley, B Ellen; Broadbridge, Christine C; Schroers, Jan

2016-10-10

The exploration of new alloys with desirable properties has been a long-standing challenge in materials science because of the complex relationship between composition and microstructure. In this Research Article, we demonstrate a combinatorial strategy for the exploration of composition dependence of microstructure. This strategy is comprised of alloy library synthesis followed by high-throughput microstructure characterization. As an example, we synthesized a ternary Au-Cu-Si composition library containing over 1000 individual alloys using combinatorial sputtering. We subsequently melted and resolidified the entire library at controlled cooling rates. We used scanning optical microscopy and X-ray diffraction mapping to explore trends in phase formation and microstructural length scale with composition across the library. The integration of combinatorial synthesis with parallelizable analysis methods provides a efficient method for examining vast compositional ranges. The availability of microstructures from this vast composition space not only facilitates design of new alloys by controlling effects of composition on phase selection, phase sequence, length scale, and overall morphology, but also will be instrumental in understanding the complex process of microstructure formation in alloys.

Sterol Synthesis in Diverse Bacteria.

Science.gov (United States)

Wei, Jeremy H; Yin, Xinchi; Welander, Paula V

2016-01-01

Sterols are essential components of eukaryotic cells whose biosynthesis and function has been studied extensively. Sterols are also recognized as the diagenetic precursors of steranes preserved in sedimentary rocks where they can function as geological proxies for eukaryotic organisms and/or aerobic metabolisms and environments. However, production of these lipids is not restricted to the eukaryotic domain as a few bacterial species also synthesize sterols. Phylogenomic studies have identified genes encoding homologs of sterol biosynthesis proteins in the genomes of several additional species, indicating that sterol production may be more widespread in the bacterial domain than previously thought. Although the occurrence of sterol synthesis genes in a genome indicates the potential for sterol production, it provides neither conclusive evidence of sterol synthesis nor information about the composition and abundance of basic and modified sterols that are actually being produced. Here, we coupled bioinformatics with lipid analyses to investigate the scope of bacterial sterol production. We identified oxidosqualene cyclase (Osc), which catalyzes the initial cyclization of oxidosqualene to the basic sterol structure, in 34 bacterial genomes from five phyla (Bacteroidetes, Cyanobacteria, Planctomycetes, Proteobacteria, and Verrucomicrobia) and in 176 metagenomes. Our data indicate that bacterial sterol synthesis likely occurs in diverse organisms and environments and also provides evidence that there are as yet uncultured groups of bacterial sterol producers. Phylogenetic analysis of bacterial and eukaryotic Osc sequences confirmed a complex evolutionary history of sterol synthesis in this domain. Finally, we characterized the lipids produced by Osc-containing bacteria and found that we could generally predict the ability to synthesize sterols. However, predicting the final modified sterol based on our current knowledge of sterol synthesis was difficult. Some bacteria

Synthesis and characterization of carbon cryogel microspheres from lignin-furfural mixtures for biodiesel production.

Science.gov (United States)

Zainol, Muzakkir Mohammad; Amin, Nor Aishah Saidina; Asmadi, Mohd

2015-08-01

The aim of this work was to study the potential of biofuel and biomass processing industry side-products as acid catalyst. The synthesis of carbon cryogel from lignin-furfural mixture, prepared via sol-gel polycondensation at 90°C for 0.5h, has been investigated for biodiesel production. The effect of lignin to furfural (L/F) ratios, lignin to water (L/W) ratios and acid concentration on carbon cryogel synthesis was studied. The carbon cryogels were characterized and tested for oleic acid conversion. The thermally stable amorphous spherical carbon cryogel has a large total surface area with high acidity. Experimental results revealed the optimum FAME yield and oleic acid conversion of 91.3wt.% and 98.1wt.%, respectively were attained at 65°C for 5h with 5wt.% catalyst loading and 20:1 methanol to oleic acid molar ratio. Therefore, carbon cryogel is highly potential for heterogeneous esterification of free fatty acid to biodiesel. Copyright © 2015 Elsevier Ltd. All rights reserved.

Synthesis and characterization of novel silver nanoparticles using Chamaemelum nobile extract for antibacterial application

Science.gov (United States)

Erjaee, Hoda; Rajaian, Hamid; Nazifi, Saeed

2017-06-01

The present study reports green synthesis of silver nanoparticles (AgNPs) at room temperature using aqueous Chamaemelum nobile extract for the first time. The effect of silver nitrate concentration, quantity of the plant extract and the reaction time on particle size was optimized and studied by UV-Vis spectroscopy and dynamic light scattering. The appearance of brownish color with λ max of 422 nm confirmed the formation of AgNPs. Synthesized nanoparticles were further characterized by Fourier transform infrared spectroscopy, x-ray diffraction and transmission electron microscopy. In addition, antimicrobial activity of the AgNPs against Escherichia coli, Salmonella typhimurium, Staphylococcus aureus and Bacillus subtilis was evaluated based on the inhibition zone using the disc-diffusion assay and measurement of minimal inhibition concentration and minimal bactericidal concentration by standard microdilution method. In conclusion, synthesis of nanoparticle with aqueous Chamaemelum nobile extract is simple, rapid, environmentally benign and inexpensive. Moreover, these synthesized nanoparticles exhibit significant antibacterial activity.

Zinc acetylacetonate hydrate adducted with nitrogen donor ligands: Synthesis, spectroscopic characterization, and thermal analysis

Science.gov (United States)

Brahma, Sanjaya; Shivashankar, S. A.

2015-12-01

We report synthesis, spectroscopic characterization, and thermal analysis of zinc acetylacetonate complex adducted by nitrogen donor ligands, such as pyridine, bipyridine, and phenanthroline. The pyridine adducted complex crystallizes to monoclinic crystal structure, whereas other two adducted complexes have orthorhombic structure. Addition of nitrogen donor ligands enhances the thermal property of these complexes as that with parent metal-organic complex. Zinc acetylacetonate adducted with pyridine shows much higher volatility (106 °C), decomposition temperature (202 °C) as that with zinc acetylacetonate (136 °C, 220 °C), and other adducted complexes. All the adducted complexes are thermally stable, highly volatile and are considered to be suitable precursors for metal organic chemical vapor deposition. The formation of these complexes is confirmed by powder X-ray diffraction, Fourier transform infrared spectroscopy, mass spectroscopy, and elemental analysis. The complexes are widely used as starting precursor materials for the synthesis of ZnO nanostructures by microwave irradiation assisted coating process.

Synthesis and Characterization of Monometallic (Ag, Cu and Bimetallic Ag-Cu Particles for Antibacterial and Antifungal Applications

Directory of Open Access Journals (Sweden)

Marta Paszkiewicz

2016-01-01

Full Text Available In this paper, the experimental studies are concerned with the effect of the synthesis parameters on the formation of monometallic Ag and Cu nanoparticles (NPs. We consider the synthesis strategies verification for the bimetallic core-shell and alloy particles preparation. It was successfully obtained by chemical reduction method. The obtained colloidal solution is characterized by the transmission electron microscopy (TEM with energy-dispersive X-ray spectroscopy (EDX data, UV-Vis spectra, particle size distribution, and zeta potential. This work presents a comprehensive overview of experimental studies of the most stable colloidal solutions to impregnate fabrics that will exhibit a bactericidal and fungicidal activity against Candida albicans, Escherichia coli, and Staphylococcus aureus.

Hydrothermal Synthesis and Characterization of a Metal-Organic Framework by Thermogravimetric Analysis, Powder X-Ray Diffraction, and Infrared Spectroscopy: An Integrative Inorganic Chemistry Experiment

Science.gov (United States)

Crane, Johanna L.; Anderson, Kelly E.; Conway, Samantha G.

2015-01-01

This advanced undergraduate laboratory experiment involves the synthesis and characterization of a metal-organic framework with microporous channels that are held intact via hydrogen bonding of the coordinated water molecules. The hydrothermal synthesis of Co[subscript 3](BTC)[subscript 2]·12H[subscript 2]O (BTC = 1,3,5-benzene tricarboxylic acid)…

Synthesis and characterization of zeolite P using technical-grade materials

CERN Document Server

Aghabozorg, H R; Aghabozorg, H R; Sharif, M

2001-01-01

Research attempts on zeolites show structural and industrial importance of these inorganic compounds. In this regard, the synthesis of zeolites is of great importance, because their natural occurring counterparts are often impure. Zeolite Na-P with a silicon to aluminium ratio of one has a better ion exchange capacity than Na-A and can be used as a detergent builder. In this work, zeolite Na-P of high purity was successfully synthesized using commercial silica and alumina sources. parameters such as H sub 2 O:A1 sub 2 O sub 3 and SiO sub 2 :A1 sub 2 O sub 3 molar ratios and crystallization temperature and time were investigated. So that the optimum condition was obtained. X-ray powder diffraction, infrared, scanning electron microscopy and elemental analysis were utilized for the characterization of the product.

Metal-organic frameworks: structure, properties, methods of synthesis and characterization

International Nuclear Information System (INIS)

Butova, V V; Soldatov, M A; Guda, A A; Lomachenko, K A; Lamberti, C

2016-01-01

This review deals with key methods of synthesis and characterization of metal-organic frameworks (MOFs). The modular structure affords a wide variety of MOFs with different active metal sites and organic linkers. These compounds represent a new stage of development of porous materials in which the pore size and the active site structure can be modified within wide limits. The set of experimental methods considered in this review is sufficient for studying the short-range and long-range order of the MOF crystal structure, determining the morphology of samples and elucidating the processes that occur at the active metal site in the course of chemical reactions. The interest in metal-organic frameworks results, first of all, from their numerous possible applications, ranging from gas separation and storage to chemical reactions within the pores. The bibliography includes 362 references

Synthesis and characterization of acrylate copolymer containing fluorescein functional group

Energy Technology Data Exchange (ETDEWEB)

Hui, Guodong; Huang, Weiyun; Song, Yunzhao; Chen, Deben; Zhong, Anyong [Sichuan University, Chengdu (China)

2013-08-15

We report a novel method to fabricate fluorescent polymer (F-CPA) based on the esterification between acrylate copolymer (CPA) and fluorescein using N, N-dicyclohexylcarbodiimide (DCC)/4-dimethylaminopyridine (DMAP) as catalyst. The resulting copolymer was characterized by Fourier transform-infrared spectroscopy (FT-IR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), ultraviolet-visible spectroscopy (UV-Vis) and fluorescence spectroscopy. In addition, the influences of concentration, solvents, pH and metal cations (Cu{sup 2+}, Fe{sup 3+} and Zn{sup 2+}) on the fluorescent behaviors of F-CPA are discussed in detail. All those observations suggest that the synthesized F-CPA is an excellent luminescent macromolecular material with simple synthesis method and excellent solubility. Moreover, its sensitive fluorescence response behaviors to solvents, pH and metal cations make it to become a polymer-based probe.

Synthesis and characterization of NiO nanoparticles by Pechini method

International Nuclear Information System (INIS)

Nascimento, A.; Ribeiro, M.A.; Costa, A.C.F.M.; Gama, L.; Bernardi, M.I.B.

2009-01-01

In recent years, ultrafine magnetic particles of NiO have attracting the attention because of its unknown behavior, enormous scientific potential and technological application. Some of its more important properties are accented magnetic moments, double dynamic exchange, quantization of wave of spin and etc. In this context, this work has for objective to synthesize and to characterize nanoparticles of NiO for the Pechini method. The powder was analyzed by X-rays diffraction. The results of scanning electron microscopy, adsorption of nitrogen. The analysis of X-rays diffraction of the sample showed single-phase peaks of NiO, with crystallite size close to 38 nm. The surface area was 6.44 m 2 /g. The image from scanning electron microscopy shows soft homogeneous agglomerates. The Pechini synthesis was efficient in the production of powders of NiO nano metrics and single-phase. (author)

Synthesis, characterization and a.c. magnetic analysis of magnetite nanoparticles

International Nuclear Information System (INIS)

Riani, P.; Napoletano, M.; Canepa, F.

2011-01-01

In the last years, the study of Fe-based magnetic nanoparticles (MNP) has attracted increasing interest either for the physical properties shown by nanosized materials (electric and magnetic properties are strongly affected by dimension and surface effects) either for the different technological applications of these materials (catalysis, drug delivery, magnetic resonance imaging, contaminants removal from groundwater, new exchange coupled magnets, soft nanomagnets for high frequency applications, etc.). In this article, the results obtained in the synthesis and characterization of the Fe 3 O 4 MNP is reported. The magnetite nanoparticles were synthesized by a modified Massart method. Structural characterization was performed using X-ray diffraction analysis and a complete morphological and dimensional study was carried out by means of Transmission Electron Microscopy, and a.c. magnetic susceptibility measured as a function of the frequency of the applied magnetic field. Diameters of the superparamagnetic Fe 3 O 4 nanoparticles are ranging from 2 to 10 nm, as evidenced by all the techniques employed. The size distribution of the hydrated aggregates in solution has been obtained by quantitative analysis of the frequency dependence of the a.c. susceptibility. The mathematical approach adopted will be described and all the obtained results will be compared and discussed.

Synthesis, Transfer, and Characterization of Nanoscale 2-Dimensional Materials

Science.gov (United States)

2015-09-01

Shi Y, Hamsen C, Jia X, Kim KK, Reina A, Hofmann M, Kong J. Synthesis of few-layer hexagonal boron nitride thin film by chemical vapor deposition...hexagonal boron nitride layers. Nano Letters. 2010;10(8):3209–3215. 12. Kim KK, Hsu A, Jia X, Kim SM, Shi Y, Hofmann M, Kong J. Synthesis of...microscopy. Physical Review B. 2009;80(15):155425. 33. Kim KK, Hsu A, Jia X, Kim SM, Shi Y, Hofmann M, Kong J. Synthesis of monolayer hexagonal boron

Radiation synthesis and characterization of zinc phthalocyanine composite based on 2-hydroxyethyl methacrylate/methyl methacrylate copolymer

International Nuclear Information System (INIS)

Abdel Ghaffar, A.M.; Youssef, Tamer E.; Mohamed, Hanan H.

2016-01-01

The synthesis and characterization of new 2-hydroxyethyl methacrylate-co-methyl methacrylate/zinc phthalocyanine composite Poly(HEMA/MMA/ZnPc) is described for the first time in this study. The aim of this research is to present possibility of radiation synthesis of the newly zinc phthalocyanine composites as potential candidates for wide range of applications. Gel (%) and swelling for Poly(hydroxyethyl methacrylate) Poly(HEMA) and the based Poly(hydroxyethyl methacrylate/methyl methacrylate) copolymer Poly(HEMA/MMA) with different composition 100/0, 95/5, 90/10 and 80/20 wt % were evaluated. It was found that Poly(HEMA/MMA) copolymer with composition 95/5 wt % characterized by its high swelling property at pH 7.4. The prepared composites I and II Poly(HEMA/MMA/ZnPc) with composition (95/5/1 wt%) and (95/5/1.5 wt%) respectively have been characterized by FTIR and TGA. The effect of gamma irradiation on the chemical properties of composite I was described. It is observed that the Zinc phthalocyanine with low concentration 1 wt % enhance chemical, thermal properties and stabilization against gamma radiation of the prepared composite I. - Highlights: • The preparation of Poly(HEMA/MMA/ZnPc) by radiation forming modified composites. • The low concentration of ZcPc (1 or 1.5 wt %) lead to form outstanding properties. • These composites are a potential candidate for wide range of applications.

Radiation synthesis and characterization of zinc phthalocyanine composite based on 2-hydroxyethyl methacrylate/methyl methacrylate copolymer

Energy Technology Data Exchange (ETDEWEB)

Abdel Ghaffar, A.M., E-mail: am_abdelghaffar@yahoo.com [Radiation Research of Polymer Chemistry Department, Industrial Irradiation Division, National Center for Radiation Research and Technology, Atomic Energy Authority P.O. Box 29, Nasr City, Cairo (Egypt); Youssef, Tamer E. [Applied Organic Chemistry Department, Chemical Industries Research Division, National Research Center, Dokki, Cairo, 12622 (Egypt); Chemical and Materials Engineering Department, Faculty of Engineering, King Abdulaziz University, P.O. Box 80204, Jeddah, 21589 (Saudi Arabia); Mohamed, Hanan H. [Chemistry Department, Faculty of Science, Helwan University, Ain Helwan, Cairo (Egypt)

2016-08-01

The synthesis and characterization of new 2-hydroxyethyl methacrylate-co-methyl methacrylate/zinc phthalocyanine composite Poly(HEMA/MMA/ZnPc) is described for the first time in this study. The aim of this research is to present possibility of radiation synthesis of the newly zinc phthalocyanine composites as potential candidates for wide range of applications. Gel (%) and swelling for Poly(hydroxyethyl methacrylate) Poly(HEMA) and the based Poly(hydroxyethyl methacrylate/methyl methacrylate) copolymer Poly(HEMA/MMA) with different composition 100/0, 95/5, 90/10 and 80/20 wt % were evaluated. It was found that Poly(HEMA/MMA) copolymer with composition 95/5 wt % characterized by its high swelling property at pH 7.4. The prepared composites I and II Poly(HEMA/MMA/ZnPc) with composition (95/5/1 wt%) and (95/5/1.5 wt%) respectively have been characterized by FTIR and TGA. The effect of gamma irradiation on the chemical properties of composite I was described. It is observed that the Zinc phthalocyanine with low concentration 1 wt % enhance chemical, thermal properties and stabilization against gamma radiation of the prepared composite I. - Highlights: • The preparation of Poly(HEMA/MMA/ZnPc) by radiation forming modified composites. • The low concentration of ZcPc (1 or 1.5 wt %) lead to form outstanding properties. • These composites are a potential candidate for wide range of applications.

Synthesis and Characterization of Highly Intercalated Graphite Bisulfate

OpenAIRE

Salvatore, Marcella; Carotenuto, Gianfranco; De Nicola, Sergio; Camerlingo, Carlo; Ambrogi, Veronica; Carfagna, Cosimo

2017-01-01

Different chemical formulations for the synthesis of highly intercalated graphite bisulfate have been tested. In particular, nitric acid, potassium nitrate, potassium dichromate, potassium permanganate, sodium periodate, sodium chlorate, and hydrogen peroxide have been used in this synthesis scheme as the auxiliary reagent (oxidizing agent). In order to evaluate the presence of delamination, and pre-expansion phenomena, and the achieved intercalation degree in the prepared samples, the obtain...

Initiation of protein synthesis in bacteria

DEFF Research Database (Denmark)

Laursen, Brian Søgaard; Sørensen, Hans Peter; Mortensen, Kim Kusk

2005-01-01

Valuable information on translation initiation is available from biochemical data and recently solved structures. We present a detailed description of current knowledge about the structure, function, and interactions of the individual components involved in bacterial translation initiation. The f...

Synthesis and characterization of carbon nano fibers for its application in the adsorption of toxic gases

International Nuclear Information System (INIS)

Juanico L, J.A.

2004-01-01

The production of carbon nano fibers (CNF's) by diverse techniques as the electric arc, laser ablation, or chemical deposition in vapor phase, among other, they have been so far used from final of the 90's. However, the synthesis method by discharge Glow arc of alternating current and high frequency developed by Pacheco and collaborators, is a once alternative for its obtaining. In the plasma Application Laboratory (LAP) of the National Institute of Nuclear Research (INlN) it was designed and manufactured a reactor of alternating current and high frequency that produces a Glow arc able to synthesize carbon nano fibers. Its were carried out nano fibers synthesis with different catalysts to different proportions and with distinct conditions of vacuum pressure and methane flow until obtaining the best nano fibers samples and for it, this nano structures were characterized by Scanning and Transmission Electron Microscopy, X-ray Diffraction, Raman spectrometry and EDS spectrometry. Once found the optimal conditions for the nano fibers production its were contaminated with NO 2 toxic gas and it was determined if they present adsorption, for it was used the thermal gravimetric analysis technique. This work is divided in three parts, in the first one, conformed by the chapters 1, at the 3, they are considered the foundations of the carbon nano fibers, their history, their characteristics, growth mechanisms, synthesis techniques, the thermal gravimetric analysis principles and the adsorption properties of the nano fibers. In the second part, consistent of the chapters 4 and 5, the methodology of synthesis and characterization of the nano fibers is provided. Finally, in third part its were carried out the activation energy calculation, the adsorption of the CNF's is analyzed and the conclusions are carried out. The present study evaluates the adsorption of environmental gas pollutants as the nitrogen oxides on carbon nano fibers at environmental or near conditions. Also

Synthesis and characterization of CuO flower-nanostructure processing by a domestic hydrothermal microwave

International Nuclear Information System (INIS)

Volanti, D.P.; Keyson, D.; Cavalcante, L.S.; Simoes, A.Z.; Joya, M.R.; Longo, E.; Varela, J.A.; Pizani, P.S.; Souza, A.G.

2008-01-01

The synthesis and characterization of CuO flower-nanostructure processed in domestic hydrothermal microwave oven was presented. Phase analysis was carried out using X-ray diffraction (XRD) and micro-Raman scattering (MRS) and the results confirmed the CuO flower-nanostructure as a single-phase. The field-emission scanning electron microscopy (FEG-SEM) was used to estimate the average spheres diameter while transmission electron microscope (TEM) to observe the thorn of the flower-nanostructures. The mechanism of CuO flower-nanostructures formation is proposed and explained

Synthesis and characterization of CuO flower-nanostructure processing by a domestic hydrothermal microwave

Energy Technology Data Exchange (ETDEWEB)

Volanti, D.P. [Laboratorio Interdisciplinar em Ceramica, Departamento de Fisico-Quimica, Instituto de Quimica, Universidade Estadual Paulista, P.O. Box 355, 14801-907 Araraquara, SP (Brazil); Keyson, D. [Laboratorio de Ensino de Ciencias e Laboratorio de Combustiveis e Materiais, Departamento de Quimica, Universidade Federal da Paraiba, 58051-900 Joao Pessoa, PB (Brazil); Cavalcante, L.S. [Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, Universidade Federal de Sao Carlos, P.O. Box 676, 13565-905 Sao Carlos, SP (Brazil)], E-mail: laeciosc@bol.com.br; Simoes, A.Z. [Laboratorio Interdisciplinar em Ceramica, Departamento de Fisico-Quimica, Instituto de Quimica, Universidade Estadual Paulista, P.O. Box 355, 14801-907 Araraquara, SP (Brazil); Joya, M.R. [Departamento de Fisica, Universidade Federal de Sao Carlos, P.O. Box 676, 13565-905 Sao Carlos, SP (Brazil); Longo, E.; Varela, J.A. [Laboratorio Interdisciplinar em Ceramica, Departamento de Fisico-Quimica, Instituto de Quimica, Universidade Estadual Paulista, P.O. Box 355, 14801-907 Araraquara, SP (Brazil); Pizani, P.S. [Departamento de Fisica, Universidade Federal de Sao Carlos, P.O. Box 676, 13565-905 Sao Carlos, SP (Brazil); Souza, A.G. [Laboratorio de Ensino de Ciencias e Laboratorio de Combustiveis e Materiais, Departamento de Quimica, Universidade Federal da Paraiba, 58051-900 Joao Pessoa, PB (Brazil)

2008-07-14

The synthesis and characterization of CuO flower-nanostructure processed in domestic hydrothermal microwave oven was presented. Phase analysis was carried out using X-ray diffraction (XRD) and micro-Raman scattering (MRS) and the results confirmed the CuO flower-nanostructure as a single-phase. The field-emission scanning electron microscopy (FEG-SEM) was used to estimate the average spheres diameter while transmission electron microscope (TEM) to observe the thorn of the flower-nanostructures. The mechanism of CuO flower-nanostructures formation is proposed and explained.

Auto-combustion Synthesis, Characterization and Photovoltaic

African Journals Online (AJOL)

NICOLAAS

Ag-NiTiO3, sol-gel method, semiconductor, photovoltaic, doping. 1. Introduction ... convenient for synthesis of pure mixed metal oxides nanoparticles. Furthermore .... current density voltage (I-V) curve for Ag-NiTiO3 was carried out under the ...

Synthesis and characterization of LiFePO{sub 4} cathode preparation by low temperature method

Energy Technology Data Exchange (ETDEWEB)

Rajesh, Desapogu, E-mail: rajesh.desapogu@gmail.com; Srinivas Naik, V.; Sunandana, C.S., E-mail: sunandana@gmail.com

2015-05-01

We review in detail the physics and technology of the novel material LiFePO{sub 4}, a potential cathode material for Li-ion batteries. In the present work, nano crystalline LiFePO{sub 4} film has been synthesized in both powder and thin film forms from a non-aqueous sol–gel synthesis route based on oxalates of Li and Fe (II). Ferrous oxalate has been synthesized indigenously using a ferrous sulphate based chemical reaction and characterized. Nano powders and thin films of LiFePO{sub 4} have been fabricated and coated on stainless steel substrates with the aim of device development in future. The material has been characterized extensively by XRD for crystal structure, FESEM for microstructure, EDS for elemental analysis and FTIR for the internal modes of phosphate ion. Fe{sup 3+} impurity characterization has been done by using ESR.

Synthesis and thermal characterization of xylan-graft-polyacrylonitrile.

Science.gov (United States)

Ünlü, Cüneyt H; Öztekin, N Simge; Atıcı, Oya Galioğlu

2012-10-01

In this study emulsion polymerization of acrylonitrile using xylan from agricultural waste material (corn cob) and cerium ammonium nitrate was investigated in terms of catalyst acid. Stock ceric solutions were prepared using either nitric or perchloric acid as catalyst. Optimum conditions were determined using different parameters such as reaction time, temperature, and component concentrations. Nitric acid catalyzed reactions resulted in maximum conversion ratio (96%) at 50°C, 1 h where ceric ion, acrylonitrile, xylan, and catalyst concentrations were 21.7 mmol l(-1), 0.5 mol l(-1), 0.2% (w/v), and 0.1 mol l(-1), respectively. However, 83% conversion was obtained with perchloric acid catalysis at 27 °C, 1 h where concentrations were 5.4 mmol l(-1), 0.8 mol l(-1), 0.5% (w/v), and 0.2 mol l(-1), respectively. Copolymer synthesis using perchloric acid was realized at milder conditions than using nitric acid. Thermal analyses of obtained polymers were conducted to characterize copolymers. Results showed that calculated activation energy, maximum degradation temperature, and heat of thermal decomposition changed relying mainly on molecular weight. Copyright © 2012 Elsevier Ltd. All rights reserved.

SYNTHESIS OF pH-RESPONSIVE AMPHIPHILIC DIBLOCK COPOLYMERS CONTAINING POLYISOBUTYLENE via OXYANION-INITIATED POLYMERIZATION AND THEIR MULTIPLE SELF-ASSEMBLY MORPHOLOGIES

Institute of Scientific and Technical Information of China (English)

Huai-chao Wang; Ming-zu Zhang; Pei-hong Ni; Jin-lin He; Ying Hao; Yi-xian Wu

2013-01-01

Two pH-responsive amphiphilic diblock copolymers,namely polyisobutylene-block-poly[2-(N,N-dimethylamino)ethyl methacrylate] (PIB-b-PDMAEMA) and polyisobutylene-block-poly(metharylic acid) (PIB-b-PMAA),were synthesized via oxyanion-initiated polymerization,and their multiple self-assembly behaviors have been studied.An exo-o1efin-terminated highly reactive polyisobutylene (HRPIB) was first changed to hydroxyl-terminated PIB (PIB-OH) via hydroboration-oxidation of C=C double bond in the chain end,and then reacted with KH to yield a potassium alcoholate of PIB (PIB-O-K+).PIB-O-K+ was immediately used as a macroinitiator to polymerize DMAEMA monomer,resulting in a cationic diblock copolymer PIB-b-PDMAEMA.With the similar synthesis procedure,the anionic diblock copolymer PIB-b-PMAA could be prepared via a combination of oxyanion-initiated polymerization of tert-butyl methacrylate (tBMA) and subsequent hydrolysis of tert-butyl ester groups in PtBMA block.The functional PIB and block copolymers have been fully characterized by 1H-NMR,FT-IR spectroscopy,and gel permeation chromatography (GPC).These samples allowed us to systematically investigate the effects of block composition on the pH responsivity and various self-assembled morphologies of the copolymers in THF/water mixed solvent.Transmission electron microscopy (TEM) images revealed that these diblock copolymers containing small amount of original PIB without exo-olefin-terminated group are able to self-assemble into micelles,vesicles with different particle sizes and cylindrical aggregates,depending on various factors including block copolymer composition,solvent polarity and pH value.

Ultrafast Hydro-Micromechanical Synthesis of Calcium Zincate: Structural and Morphological Characterizations

Directory of Open Access Journals (Sweden)

Vincent Caldeira

2017-01-01

Full Text Available Calcium zincate is a compound with a large panel of application: mainly known as an advantageous replacement of zinc oxide in negative electrodes for air-zinc or nickel-zinc batteries, it is also used as precursor catalyst in biodiesel synthesis and as antifungal compound for the protection of limestone monuments. However, its synthesis is not optimized yet. In this study, it was elaborated using an ultrafast synthesis protocol: Hydro-Micromechanical Synthesis. Two other synthesis methods, Hydrochemical Synthesis and Hydrothermal Synthesis, were used for comparison. In all cases, the as-synthesized samples were analyzed by X-ray diffraction, scanning electron microscopy, and LASER diffraction particle size analysis. Rietveld method was used to refine various structural parameters and obtain an average crystallite size, on a Hydro-Micromechanical submicronic sample. X-ray single crystal structure determination was performed on a crystal obtained by Hydrochemical Synthesis. It has been shown that regardless of the synthesis protocol, the prepared samples always crystallize in the same crystal lattice, with P21/c space group and only differ from their macroscopic textural parameters. Nevertheless, only the Hydro-Micromechanical method is industrially scalable and enables a precise control of the textural parameters of the obtained calcium zincate.

Synthesis and characterization of noble metal–titania core–shell nanostructures with tunable shell thickness

Directory of Open Access Journals (Sweden)

Bartosz Bartosewicz

2017-10-01

Full Text Available Core–shell nanostructures have found applications in many fields, including surface enhanced spectroscopy, catalysis and solar cells. Titania-coated noble metal nanoparticles, which combine the surface plasmon resonance properties of the core and the photoactivity of the shell, have great potential for these applications. However, the controllable synthesis of such nanostructures remains a challenge due to the high reactivity of titania precursors. Hence, a simple titania coating method that would allow better control over the shell formation is desired. A sol–gel based titania coating method, which allows control over the shell thickness, was developed and applied to the synthesis of Ag@TiO2 and Au@TiO2 with various shell thicknesses. The morphology of the synthesized structures was investigated using scanning electron microscopy (SEM. Their sizes and shell thicknesses were determined using tunable resistive pulse sensing (TRPS technique. The optical properties of the synthesized structures were characterized using UV–vis spectroscopy. Ag@TiO2 and Au@TiO2 structures with shell thickness in the range of ≈40–70 nm and 90 nm, for the Ag and Au nanostructures respectively, were prepared using a method we developed and adapted, consisting of a change in the titania precursor concentration. The synthesized nanostructures exhibited significant absorption in the UV–vis range. The TRPS technique was shown to be a very useful tool for the characterization of metal–metal oxide core–shell nanostructures.

Synthesis and characterization of polyphosphazene electrolytes including cyclic ether side groups

Science.gov (United States)

Fiedler, Carsten; Luerssen, Bjoern; Lucht, Brett; Janek, Juergen

2018-04-01

This paper presents the synthesis and detailed characterization of two polyphosphazene based polymers, including different cyclic ether side groups. The final polymers were obtained by a well-known method employing a living cationic polymerization and subsequent nucleophilic substitution. The synthesized polymers Poly [(1,3-dioxane-5-oxy) (1,3-dioxolane-4-methoxy)phosphazene] (DOPP) and Poly[bis(2-Tetrahydro-3-furanoxy)phosphazene] (THFPP) were mixed with varied amounts of lithium bis(trifluoromethane)sulfonamide (LiTFSI) and the interactions between the salt and the polymer chains were studied by Fourier transform infrared (FT-IR) and differential scanning calorimetry (DSC) measurements. Electrochemical characterization was performed by electrochemical impedance spectroscopy (EIS) and direct current polarization in the temperature range of 20-60 °C. These measurements were utilized to calculate the lithium transference number (t+), the lithium conductivity (σ) and its activation energy in order to elucidate the lithium transport behavior. Relatively high lithium transference numbers of 0.6 (DOPP) and 0.7 (THFPP) at 60 °C are found and reveal maximum lithium conductivities of 2.8·10-6 Sṡcm-1 and 9.0·10-7 Sṡcm-1 for DOPP and THFPP at 60 °C, respectively.

Synthesis and characterization of polycaprolactone for anterior cruciate ligament regeneration

Energy Technology Data Exchange (ETDEWEB)

Gurlek, Ayse Cansu; Sevinc, Burcu; Bayrak, Ece; Erisken, Cevat, E-mail: cerisken@etu.edu.tr

2017-02-01

Anterior cruciate ligament (ACL) is the most frequently torn ligament in the knee, and complete healing is unlikely due to lack of vascularization. Current approaches for the treatment of ACL injuries include surgical interventions and grafting, however recent reports show that surgeries have 94% recurrency, and that repaired tissues are biomechanically inferior to the native tissue. These necessitate the need for new strategies for scar-free repair/regeneration of ACL injuries. Polycaprolactone (PCL) is a biodegradable and biocompatible synthetic polymer, which has been widely used in the connective tissue repair/regeneration attempts. Here, we report on the synthesis of PCL via ring opening polymerization using ε-caprolactone as the monomer, and ammonium heptamolybdate as a catalyst. The synthesized PCL was characterized using Fourier Transform Infrared Spectroscopy (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. It was then processed using electrospinning to form nanofiber-based scaffolds. These scaffolds were characterized in terms of surface as well as mechanical properties, and compared to the properties of commercially available PCL, and of native ACL tissue harvested from sheep. In addition, scaffolds fabricated with synthesized PCL were evaluated regarding their cell attachment capacity using human bone marrow mesenchymal stem cells (hBMSCs). Our findings demonstrated that the synthesized PCL is similar to its commercially available counterpart in terms of surface morphology and mechanical properties. In addition, fibrous scaffolds generated with electrospinning showed weaker mechanical properties visa vis native ACL tissue in terms of ultimate stress, and elastic modulus. Also, the synthesized PCL can accommodate cell attachment when tested with hBMSCs. Putting together, these observations reveal that the PCL synthesized in this study could be a good candidate as a biomaterial for ligament repair or regeneration. - Highlights: • Synthesis of

Synthesis and characterization of polycaprolactone for anterior cruciate ligament regeneration

International Nuclear Information System (INIS)

Gurlek, Ayse Cansu; Sevinc, Burcu; Bayrak, Ece; Erisken, Cevat

2017-01-01

Anterior cruciate ligament (ACL) is the most frequently torn ligament in the knee, and complete healing is unlikely due to lack of vascularization. Current approaches for the treatment of ACL injuries include surgical interventions and grafting, however recent reports show that surgeries have 94% recurrency, and that repaired tissues are biomechanically inferior to the native tissue. These necessitate the need for new strategies for scar-free repair/regeneration of ACL injuries. Polycaprolactone (PCL) is a biodegradable and biocompatible synthetic polymer, which has been widely used in the connective tissue repair/regeneration attempts. Here, we report on the synthesis of PCL via ring opening polymerization using ε-caprolactone as the monomer, and ammonium heptamolybdate as a catalyst. The synthesized PCL was characterized using Fourier Transform Infrared Spectroscopy (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. It was then processed using electrospinning to form nanofiber-based scaffolds. These scaffolds were characterized in terms of surface as well as mechanical properties, and compared to the properties of commercially available PCL, and of native ACL tissue harvested from sheep. In addition, scaffolds fabricated with synthesized PCL were evaluated regarding their cell attachment capacity using human bone marrow mesenchymal stem cells (hBMSCs). Our findings demonstrated that the synthesized PCL is similar to its commercially available counterpart in terms of surface morphology and mechanical properties. In addition, fibrous scaffolds generated with electrospinning showed weaker mechanical properties visa vis native ACL tissue in terms of ultimate stress, and elastic modulus. Also, the synthesized PCL can accommodate cell attachment when tested with hBMSCs. Putting together, these observations reveal that the PCL synthesized in this study could be a good candidate as a biomaterial for ligament repair or regeneration. - Highlights: • Synthesis of

SYNTHESIS OF STYRENE-METHYL METHACRYLATE BLOCK COPOLYMER BY POLYAZOAMIDE AS INITIATOR

Institute of Scientific and Technical Information of China (English)

WANG Zhongyi; WEI Jeqing

1996-01-01

Polyazoamide(PAA) was used as initiator to prepare block copolymer P(MMA-b-St) by free radical polymerization. The fraction of block copolymer was about 50%. The structure of the block-copolymer was characterized by IR and the results of 1H-NMR and GPC showed that the content of the block and the molecular weight (-Mw) of the prepolymer and block copolymer could be controlled by varying the mol ratio of styrene/PAA and MMA/prepolymer. DSC and TEM results revealed that the block copolymer has two separated glass transition temperatures and phase separation within the domain structure.

Synthesis, characterization and catalytic application of silica supported tin oxide nanoparticles for synthesis of 2,4,5-tri and 1,2,4,5-tetrasubstituted imidazoles under solvent-free conditions

Directory of Open Access Journals (Sweden)

Ashok V. Borhade

2017-02-01

Full Text Available Highly efficient and eco-friendly, one pot synthesis of 1,2,4,5-tetra substituted imidazoles and 2,4,5-trisubstituted imidazoles was reported under solvent free conditions using nanocrystalline silica supported tin oxide (SiO2:SnO2 as a catalyst with excellent yield. The present methodology offers several advantages such as mild reaction conditions, short reaction time, good yield, high purity of product, recyclable catalyst without a noticeable decrease in catalytic activity and can be used for large scale synthesis. The synthesized SiO2:SnO2 nanocrystalline catalyst was characterized by XRD, BET surface area and TEM techniques.

Colloidal phytosterols: synthesis, characterization and bioaccessibility

NARCIS (Netherlands)

Rossi, L.; Seijen ten Hoorn, J.W.M.; Melnikov, S.M.; Velikov, K.P.

2010-01-01

We demonstrate the synthesis of phytosterol colloidal particles using a simple food grade method based on antisolvent precipitation in the presence of a non-ionic surfactant. The resulting colloidal particles have a rod-like shape with some degree of crystallinity. The colloidal dispersions display

Synthesis, characterization and TG-DSC study of cadmium halides adducts with caffeine

Energy Technology Data Exchange (ETDEWEB)

Farias, Robson F. de; Silva, Ademir O. da; Silva, Umberto G. da

2003-11-28

The synthesis, characterization and TG-DSC study of the compounds CdX{sub 2}{center_dot}ncaff, for which X: Cl, Br and I; n=1 and 2 and caff: caffeine is reported. It is verified that caffeine is coordinated through more than one coordination site, despite the fact that the nitrogen of the imidazole ring is the main coordination site. The following thermal stability trend is observed: Cl>Br>I and monoadducts are more stable than bisadducts. The thermal degradation (td) enthalpies have the values (kJ mol{sup -1}): 58.2 and 71.5; 74.9 and 91.4; 31.1 and 47.5 for Cl, Br and I mono and bisadducts, respectively.

A short designed semi-aromatic organic nanotube – synthesis, chiroptical characterization, and host properties

DEFF Research Database (Denmark)

Wixe, Torbjörn; Christensen, Niels Johan; Lidin, Sven

2014-01-01

to molecular dynamics simulations in chloroform). The synthesis of the tube, a heptamer, is based on a series of Friedländer condensations and the use of pyrido[3,2-d]pyrimidine units as masked 2-amino aldehydes, as a general means to propagate organic tubular structures and the introduction of a methoxy group...... for modification toward solubility and functionalization are described. The electronic CD spectra of the tube and molecular intermediates are correlated with theoretical spectra calculated with time-dependent density functional theory to characterize the chirality of the tube. Both experimental (NMR...

Niobium-Doped Hydroxyapatite Bioceramics: Synthesis, Characterization and In Vitro Cytocompatibility

Directory of Open Access Journals (Sweden)

Nádia S. V. Capanema

2015-07-01

Full Text Available Doping calcium phosphates with ionic species can play an important role in biological responses promoting alkaline phosphatase activity, and, therefore inducing the generation of new bone. Thus, in this study, the synthesis of niobium-doped hydroxyapatite (Nb-HA nanosize particles obtained by the precipitation process in aqueous media followed by thermal treatment is presented. The bioceramics were extensively characterized by X-ray diffraction, wavelength dispersive X-ray fluorescence spectrometry, Fourier transform infrared spectroscopy, scanning electron microscopy/energy dispersive X-ray spectroscopy analysis, transmission electron microscopy, atomic force microscopy and thermal analysis regarding their chemical composition, structure and morphology. The results showed that the precipitate dried at 110 °C was composed of amorphous calcium phosphate and HA, with polidisperse particles ranging from micro to nano dimensions. After the thermal treatment at 900 °C, the bioceramic system evolved predominantly to HA crystalline phase, with evident features of particle sintering and reduction of surface area. Moreover, the addition of 10 mol% of niobium salt precursor during the synthesis indicated the complete incorporation of the Nb(V species in the HA crystals with detectable changes in the original lattice parameters. Furthermore, the incorporation of Nb ions caused a significant refinement on the average particle size of HA. Finally, the preliminary cytocompatibility response of the biomaterials was accessed by human osteoblast cell culture using MTT and resazurin assays, which demonstrated no cytotoxicity of the Nb-alloyed hydroxyapatite. Thus, these findings seem promising for developing innovative Nb-doped calcium phosphates as artificial biomaterials for potential use in bone replacements and repair.

V2O5 xerogel-poly(ethylene oxide) hybrid material: Synthesis, characterization, and electrochemical properties

International Nuclear Information System (INIS)

Guerra, Elidia M.; Ciuffi, Katia J.; Oliveira, Herenilton P.

2006-01-01

In this work, we report the synthesis, characterization, and electrochemical properties of vanadium pentoxide xerogel-poly(ethylene oxide) (PEO) hybrid materials obtained by varying the average molecular weight of the organic component as well as the components' ratios. The materials were characterized by X-ray diffraction, ultraviolet/visible and infrared spectroscopies, thermogravimetric analysis, scanning electron microscopy, electron paramagnetic resonance, and cyclic voltammetry. Despite the presence of broad and low intensity peaks, the X-ray diffractograms indicate that the lamellar structure of the vanadium pentoxide xerogel is preserved, with increase in the interplanar spacing, giving evidence of a low-crystalline structure. We found that the electrochemical behaviour of the hybrid materials is quite similar to that found for the V 2 O 5 xerogel alone, and we verified that PEO leads to stabilization and reproducibility of the Li + electrochemical insertion/de-insertion into the V 2 O 5 xerogel structure, which makes these materials potential components of lithium ion batteries. - Graphical abstract: The synthesis, structural and electrochemical properties of vanadium pentoxide xerogel-poly(ethylene oxide) hybrid materials have been described. Despite the presence of broad and low intensity peaks, the X-ray diffractograms indicate that the lamellar structure of the vanadium pentoxide xerogel is preserved. The cyclic voltammetry technique demonstrated that PEO intercalation provides an improvement in the electrochemical properties, mainly with respect to the lithium electroinsertion process into the oxide matrix

Synthesis and characterization of irradiated injectable bone substitute paste based on hydroxyapatite

International Nuclear Information System (INIS)

Yessy Warastuti; Basril Abbas

2011-01-01

Synthesis and characterization of hydroxyapatite, chitosan and hydroxypropyl methylcellulose (HPMC) composite in injectable paste form have been done. The composite was synthesized by stirring hydroxyapatite, chitosan and HPMC until homogen. IBS paste was irradiated at the dose of 25 kGy (sterile dose). Characterization of IBS paste was conducted by measuring of the water content, identification of functional group with Fourier Transform Infra Red Spectrophotometer (FTIR), and identification of sample morphology with Scanning Electron Microscope Energy Dispersive Spectrophotometer (SEM EDS). The result showed that the water content of irradiated sample was higher than unirradiated sample due to water radiolysis. Several specific bands of IBS paste were identified, i.e., carbonate (CO 3 2- ), at 1420 cm -1 , phosphate (PO 4 3- ) at 1043 cm -1 , 605 cm -1 , 568 cm -1 and chitosan (NH 2 ) at 1599 cm -1 . There is no significant difference in absorbed band between irradiated and unirradiated samples. IBS paste has a microstructure with the size of 0.05 – 0.1 μm. Electron beam irradiation did not change the structure and morphology of sample. (author)

Synthesis and characterization of hematite pigment obtained from a steel waste industry

Energy Technology Data Exchange (ETDEWEB)

Prim, S.R. [Department of Mechanical Engineering, University of the State of Santa Catarina, Santa Catarina (Brazil); Folgueras, M.V., E-mail: dem2mvf@joinville.udesc.br [Department of Mechanical Engineering, University of the State of Santa Catarina, Santa Catarina (Brazil); Lima, M.A. de [Department of Mechanical Engineering, University of the State of Santa Catarina, Santa Catarina (Brazil); Hotza, D. [Departamento de Engenharia Quimica, Federal University of Santa Catarina, Santa Catarina (Brazil)

2011-09-15

Highlights: {yields} The study of using of a industrial waste for the synthesis of hematite pigments. {yields} The nanometer dimension this waste and your behavior as chromophore. {yields} The effect of process variables on the mechanisms of encapsulation sintered pigments. - Abstract: Pigments that meet environmental and technology requirements are the focus of the research in the ceramic sector. This study focuses on the synthesis of ceramic pigment by encapsulation of hematite in crystalline and amorphous silica matrix. Iron oxide from a metal sheet rolling process was used as chromophore. A different content of hematite and silica was homogenized by conventional and high energy milling. The powders obtained after calcinations between 1050 and 1200 {sup o}C for 2 h were characterized by X-ray diffraction and SEM analysis. The pigments were applied to ceramic enamel and porcelain body. The effect of pigment was measured by comparing L*a*b* values of the heated samples. Results showed that the color developed is influenced by variables such as oxide content employed, conditions of milling and processing temperature. The results showed that the use of pigment developed does not interfere in microstructural characteristics of pigmented material. The best hue was obtained from samples with 15 wt% of chromophore, heated at 1200 {sup o}C in amorphous silica matrix.

Synthesis and physicochemical characterizations and antimicrobial activity of ZnO nanoparticles

Science.gov (United States)

Sharma, Bhumika K.; Patel, Kinjal; Roy, Debesh R.

2018-05-01

Nanoparticles exhibit very interesting and useful physicochemical properties when they interact with substrates and goes through some physicochemical and/or biological processes. ZnO is known to be a highly demanding nanomaterial due to its discreet properties, shapes and sizes. A detail experimental study on the synthesis, characterization and antibacterial activity of ZnO nanoparticles (NPs) is performed. ZnO NPs are synthesized using chemical precipitation method. The understanding of crystal structure, morphology and elemental compositions are explained using Powder X-Ray Diffraction (XRD) and Field Emission Scanning Electron Microscope (FE-SEM) respectively. Fourier transform infrared spectroscopy (FTIR) is performed to achieve the information on the presence of various functional groups. The antibacterial activity of these ZnO NPs is investigated in terms of Zone of Inhibition (ZOI) against Escherichia coli (Gram negative) microorganisms.

Alternative chemical-based synthesis routes and characterization of nano-scale particles

International Nuclear Information System (INIS)

Brocchi, E.A.; Motta, M.S.; Solorzano, I.G.; Jena, P.K.; Moura, F.J.

2004-01-01

Different nano-scale particles have been synthesized by alternative routes: nitrates dehydratation and oxide, or co-formed oxides, reduction by hydrogen. Chemical-based synthesis routes are described and thermodynamics studies and kinetics data are presented to support the feasibility for obtaining single-phase oxides and co-formed two-phase oxides. In addition, the reduction reaction has been applied to successfully produce metal/ceramic nanocomposites. Structural characterization has been carried out by means of X-ray diffraction and, more extensively, transmission electron microscopy operating in conventional diffraction contrast mode (CTEM) and high-resolution mode (HRTEM). Nano-scale size distribution of oxide particles is well demonstrated together with their defect-free structure in the lower range, around 20 nm, size. Structural features related to the synthesized nano-composites are also presented

SYNTHESIS, CHARACTERIZATION AND ANTIOXIDANT ACTIVITY OF 7-HYDROXY-3',4'-DIMETHOXYFLAVONE

Directory of Open Access Journals (Sweden)

Elfi Susanti VH

2012-03-01

Full Text Available Synthesis of flavones and their derivatives has attracted considerable attention due to their significant pharmaceutical effects. 7-hydroxy-3',4'-dimethoxyflavone has been synthesized and its antioxidant activity has been investigated. Flavone was synthesized by oxidative cyclization of chalcone. 2',4'-dihydroxy-3,4-dimethoxychalcone was prepared by Claisen-Schmidt condensation of 2,4-dihydroxyacetophenones with 3,4-dimethoxybenzaldehydes in the presence of aqueous solution of sodium hydroxide and ethanol at room temperature. Oxidative cyclization of 2',4'-dihydroxy-3,4-dimethoxychalcone was done by using I2 catalyst in DMSO to form 7-hydroxy-3',4'-dimethoxyflavone. The synthesized compounds were characterized by means of their UV-Vis, IR, 1H-NMR and 13C-NMR spectral data. The compound was tested for their antioxidant activities by DPPH method.

Synthesis and Characterization of Oxide Feedstock Powders for the Fuel Cycle R and D Program

International Nuclear Information System (INIS)

Voit, Stewart L.; Vedder, Raymond James; Johnson, Jared A.

2010-01-01

Nuclear fuel feedstock properties, such as physical, chemical, and isotopic characteristics, have a significant impact on the fuel fabrication process and, by extension, the in-reactor fuel performance. This has been demonstrated through studies with UO 2 spanning greater than 50 years. The Fuel Cycle R and D Program with The Department of Energy Office of Nuclear Energy has initiated an effort to develop a better understanding of the relationships between oxide feedstock, fresh fuel properties, and in-reactor fuel performance for advanced mixed oxide compositions. Powder conditioning studies to enable the use of less than ideal powders for ceramic fuel pellet processing are ongoing at Los Alamos National Laboratory (LANL) and an understanding of methods to increase the green density and homogeneity of pressed pellets has been gained for certain powders. Furthermore, Oak Ridge National Laboratory (ORNL) is developing methods for the co-conversion of mixed oxides along with techniques to analyze the degree of mixing. Experience with the fabrication of fuel pellets using co-synthesized multi-constituent materials is limited. In instances where atomically mixed solid solutions of two or more species are needed, traditional ceramic processing methods have been employed. Solution-based processes may be considered viable synthesis options, including co-precipitation (AUPuC), direct precipitation, direct-conversion (Modified Direct Denitration or MDD) and internal/external gelation (sol-gel). Each of these techniques has various advantages and disadvantages. The Fiscal Year 2010 feedstock development work at ORNL focused on the synthesis and characterization of one batch of UO x and one batch of U 80 Ce 20 O x . Oxide material synthesized at ORNL is being shipped to LANL for fuel fabrication process development studies. The feedstock preparation was performed using the MDD process which utilizes a rotary kiln to continuously thermally denitrate double salts of ammonium

Synthesis and characterization of CdxMn1-xS nanoparticles stabilized with poly(vinyl alcohol)

International Nuclear Information System (INIS)

Schatkoski, Vanessa M.; Mansur, Alexandra A.P.; Mansur, Herman S.; Gonzalez, Juan C.

2011-01-01

Colloidal luminescent semiconductor nanocrystals, also known as quantum dots, have attracted considerable attention due to their significant potential application. The doping of nanocrystalline semiconductors with divalent manganese ions results in new optical properties of these semimagnetic semiconductor quantum dots. In this work we report the synthesis and characterization Cd x Mn 1-x S nanoparticles using poly(vinyl alcohol) as stabilizing agent. Different fractions of Cd 2+ /Mn 2+ ions were investigated aiming the production of stable nanoparticles with different photoluminescence properties. (author)

Synthesis, characterization and initial evaluation of 5-nitro-1-(trifluoromethyl-3H-1λ3,2-benziodaoxol-3-one

Directory of Open Access Journals (Sweden)

Nico Santschi

2014-01-01

Full Text Available The synthesis of 5-nitro-1-(trifluoromethyl-3H-1λ3,2-benziodaoxol-3-one (3, a hypervalent-iodine-based electrophilic trifluoromethylating reagent, is described. Whereas considerations based on cyclic voltammetry and X-ray structural properties would predict an inferior reactivity when compared to the non-nitrated derivative 2, 19F NMR kinetic studies showed that this new derivative is almost one order of magnitude more reactive. Furthermore, differential scanning calorimetry measurements indicated that, in addition, it is also safer to handle.

Synthesis and Characterization of Cobalt Containing Nanoparticles on Alumina A Potential Catalyst for Gas to Liquid Fuels Production

Science.gov (United States)

Cowen, Jonathan; Hepp, Aloysius F.

2016-01-01

Fisher-Tröpsch synthesis (FTS) is a century-old gas-to-liquid (GTL) technology that commonly employs cobalt (Co, on an oxide support) or iron (supported or not) species catalysts. It has been well established that the activity of the Co catalyst depends directly upon the number of surface Co atoms. The addition of promoter (mainly noble) metals has been widely utilized to increase the fraction of Co that is available for surface catalysis. Direct synthesis of Co nanoparticles is a possible alternative approach; our preliminary synthesis and characterization efforts are described. Materials were characterized by various transmission microscopies and energy dispersive spectroscopy. Tri-n-octylphosphine oxide (TOPO) and dicobalt octacarbonyl were heated under argon to a temperature of 180 deg with constant stirring for 1 hr. Quenching the reaction in toluene produced Co-containing nanoparticles with a diameter of 5 to 10 nm. Alternatively, an alumina support (SBA-200 Al2O3) was added; the reaction was further stirred and the temperature was decreased to 140 deg to reduce the rate of further growth/ripening of the nucleated Co nanoparticles. A typical size of Co-containing NPs was also found to be in the range of 5 to 10 nm. This can be contrasted with a range of 50 to 200 nm for conventionally-produced Co-Al2O3 Fischer-Tröpsch catalysts. This method shows great potential for production of highly dispersed catalysts that are either supported or unsupported.

Silver Nanoparticles: Synthesis, Characterization, Properties, Applications, and Therapeutic Approaches

Science.gov (United States)

Zhang, Xi-Feng; Liu, Zhi-Guo; Shen, Wei; Gurunathan, Sangiliyandi

2016-01-01

Recent advances in nanoscience and nanotechnology radically changed the way we diagnose, treat, and prevent various diseases in all aspects of human life. Silver nanoparticles (AgNPs) are one of the most vital and fascinating nanomaterials among several metallic nanoparticles that are involved in biomedical applications. AgNPs play an important role in nanoscience and nanotechnology, particularly in nanomedicine. Although several noble metals have been used for various purposes, AgNPs have been focused on potential applications in cancer diagnosis and therapy. In this review, we discuss the synthesis of AgNPs using physical, chemical, and biological methods. We also discuss the properties of AgNPs and methods for their characterization. More importantly, we extensively discuss the multifunctional bio-applications of AgNPs; for example, as antibacterial, antifungal, antiviral, anti-inflammatory, anti-angiogenic, and anti-cancer agents, and the mechanism of the anti-cancer activity of AgNPs. In addition, we discuss therapeutic approaches and challenges for cancer therapy using AgNPs. Finally, we conclude by discussing the future perspective of AgNPs. PMID:27649147

Vapor-phase synthesis and characterization of ZnSe nanoparticles

Science.gov (United States)

Sarigiannis, D.; Pawlowski, R. P.; Peck, J. D.; Mountziaris, T. J.; Kioseoglou, G.; Petrou, A.

2002-06-01

Compound semiconductor nanoparticles are an exciting class of materials whose unique optical and electronic properties can be exploited in a variety of applications, including optoelectronics, photovoltaics, and biophotonics. The most common route for synthesizing such nanoparticles has been via liquid-phase chemistry in reverse micelles. This paper discusses a flexible vapor-phase technique for synthesis of crystalline compound semiconductor nanoparticles using gas-phase condensation reactions near the stagnation point of a counterflow jet reactor. ZnSe nanoparticles were formed by reacting vapors of dimethylzinc: triethylamine adduct and hydrogen selenide at 120Torr and room temperature (28°C). No attempt was made to passivate the surface of the particles, which were collected as random aggregates on silicon wafers or TEM grids placed downstream of the reaction zone. Particle characterization using TEM, electron diffraction, Raman and EDAX revealed that the aggregates consisted of polycrystalline ZnSe nanoparticles, almost monodisperse in size (with diameters of ~40nm). The polycrystalline nanoparticles appear to have been formed by coagulation of smaller single-crystalline nanoparticles with characteristic size of 3-5 run.

Synthesis, characterization, applications, and challenges of iron oxide nanoparticles

Science.gov (United States)

Ali, Attarad; Zafar, Hira; Zia, Muhammad; ul Haq, Ihsan; Phull, Abdul Rehman; Ali, Joham Sarfraz; Hussain, Altaf

2016-01-01

Recently, iron oxide nanoparticles (NPs) have attracted much consideration due to their unique properties, such as superparamagnetism, surface-to-volume ratio, greater surface area, and easy separation methodology. Various physical, chemical, and biological methods have been adopted to synthesize magnetic NPs with suitable surface chemistry. This review summarizes the methods for the preparation of iron oxide NPs, size and morphology control, and magnetic properties with recent bioengineering, commercial, and industrial applications. Iron oxides exhibit great potential in the fields of life sciences such as biomedicine, agriculture, and environment. Nontoxic conduct and biocompatible applications of magnetic NPs can be enriched further by special surface coating with organic or inorganic molecules, including surfactants, drugs, proteins, starches, enzymes, antibodies, nucleotides, nonionic detergents, and polyelectrolytes. Magnetic NPs can also be directed to an organ, tissue, or tumor using an external magnetic field for hyperthermic treatment of patients. Keeping in mind the current interest in iron NPs, this review is designed to report recent information from synthesis to characterization, and applications of iron NPs. PMID:27578966

SiO2@TiO2 Coating: Synthesis, Physical Characterization and Photocatalytic Evaluation

Directory of Open Access Journals (Sweden)

A. Rosales

2018-03-01

Full Text Available Use of silicon dioxide (SiO2 and titanium dioxide (TiO2 have been widely investigated individually in coatings technology, but their combined properties promote compatibility for different innovative applications. For example, the photocatalytic properties of TiO2 coatings, when exposed to UV light, have interesting environmental applications, such as air purification, self-cleaning and antibacterial properties. However, as reported in different pilot projects, serious durability problems, associated with the adhesion between the substrate and TiO2, have been evidenced. Thus, the aim of this work is to synthesize SiO2 together with TiO2 to increase the durability of the photocatalytic coating without affecting its photocatalytic potential. Therefore, synthesis using sonochemistry, synthesis without sonochemistry, physical characterization, photocatalytic evaluation, and durability of the SiO2, SiO2@TiO2 and TiO2 coatings are presented. Results indicate that using SiO2 improved the durability of the TiO2 coating without affecting its photocatalytic properties. Thus, this novel SiO2@TiO2 coating shows potential for developing long-lasting, self-cleaning and air-purifying construction materials.

Synthesis and Characterization of CdS/TiO2-Montmorillonite Nanocomposite with Enhanced Visible-Light Absorption

OpenAIRE

Feng-shan Zhou; Dai-mei Chen; Bao-lin Cui; Wei-heng Wang

2014-01-01

Sodium montmorillonite (MMT) was chosen as the carrier; a serial of CdS/TiO2-MMT nanocomposites with enhanced visible-light absorption ability was prepared by hydrothermal synthesis method combination with semiconductor compound modification method. The samples are characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and ultraviolet visible (UV-Vis) spectroscopy; the results showed that TiO2 and CdS nanoparticles were loaded on the surface of montmorillonite unifo...

Synthesis and characterization of nanostructured CaSiO3 biomaterial

Science.gov (United States)

Jagadale, Pramod N.; Kulal, Shivaji R.; Joshi, Meghanath G.; Jagtap, Pramod P.; Khetre, Sanjay M.; Bamane, Sambhaji R.

2013-04-01

Here we report a successful preparation of nanostructured calcium silicate by wet chemical approach. The synthesized sample was characterized by various physico-chemical methods. Thermal stability was investigated using thermo-gravimetric and differential thermal analysis (TG-DTA). Structural characterization of the sample was carried out by the X-ray diffraction technique (XRD) which confirmed its single phase hexagonal structure. Transmission electron microscopy (TEM) was used to study the nanostructure of the ceramics while homogeneous grain distribution was revealed by scanning electron microscopy studies (SEM). The elemental analysis data obtained from energy dispersive X-ray spectroscopy (EDAX) were in close agreement with the starting composition used for the synthesis. Superhydrophilic nature of CaSiO3 was investigated at room temperature by sessile drop technique. Effect of porous nanosized CaSiO3 on early adhesion and proliferation of human bone marrow mesenchymal stem cells (BMMSCs) and cord blood mesenchymal stem (CBMSCs) cells was measured in vitro. MTT cytotoxicity test and cell adhesion test showed that the material had good biocompatibility and promoted cell viability and cell proliferation. It has been stated that the cell viability and proliferation are significantly affected by time and concentration of CaSiO3. These findings indicate that the CaSiO3 ceramics has good biocompatibility and that it is promising as a biomaterial.

Template-Assisted Synthesis and Characterization of Passivated Nickel Nanoparticles

Directory of Open Access Journals (Sweden)

Al-Omari IA

2010-01-01

Full Text Available Abstract Potential applications of nickel nanoparticles demand the synthesis of self-protected nickel nanoparticles by different synthesis techniques. A novel and simple technique for the synthesis of self-protected nickel nanoparticles is realized by the inter-matrix synthesis of nickel nanoparticles by cation exchange reduction in two types of resins. Two different polymer templates namely strongly acidic cation exchange resins and weakly acidic cation exchange resins provided with cation exchange sites which can anchor metal cations by the ion exchange process are used. The nickel ions which are held at the cation exchange sites by ion fixation can be subsequently reduced to metal nanoparticles by using sodium borohydride as the reducing agent. The composites are cycled repeating the loading reduction cycle involved in the synthesis procedure. X-Ray Diffraction, Scanning Electron Microscopy, Transmission Electron microscopy, Energy Dispersive Spectrum, and Inductively Coupled Plasma Analysis are effectively utilized to investigate the different structural characteristics of the nanocomposites. The hysteresis loop parameters namely saturation magnetization and coercivity are measured using Vibrating Sample Magnetometer. The thermomagnetization study is also conducted to evaluate the Curie temperature values of the composites. The effect of cycling on the structural and magnetic characteristics of the two composites are dealt in detail. A comparison between the different characteristics of the two nanocomposites is also provided.

Modified solvothermal synthesis and characterization of CdS/ZnS core/shell nanorods

International Nuclear Information System (INIS)

Baby Suganthi, A.R.; Sagayaraj, P.

2013-01-01

Core/shell CdS/ZnS nanorods were synthesized using a two-step solvothermal approach. The first step is the formation of CdS nanoparticles initiated using nucleation followed by growth through coalescence-exchange and particle coagulation. The second step leads to the formation of ZnS and further coalescence-exchange leading to deposition and growth of a ZnS shell around CdS nanoparticles. The structural, morphological and chemical studies were performed using X-ray diffraction, Energy Dispersive X-ray spectroscopy (EDX) Scanning electron Microscopy (SEM), UV–vis absorption spectra and Transmission Electron Microscopy (TEM), provide direct evidence for shell growth. The present synthesis provides a rational approach to the design of novel core/shell nanomaterials with appealing applications in optoelectronic devices. - Graphical abstract: From the resulting TEM images, the formation of core/shell could be observed. The apparent microscopy contrast between the CdS core and the ZnS shell offers evidence for the formation of CdS/ZnS core/shell nanostructures. It is clearly evident that the surfaces of the nanorods became rough after coating and also the diameter of the nanorod is seen increased up to 40–50 nm. Highlights: ► CdS/ZnS core/shell nanorods were synthesized using two-step solvothermal approach. ► The nanoparticles were characterized by XRD, EDX, SEM, UV–vis and TEM. ► SEM images revealed the surface roughness after ZnS shell growth. ► TEM microscopy offers evidence for the formation of core/shell nanostructures

Characterization of the crystalline quality of β-SiC formed by ion beam synthesis

International Nuclear Information System (INIS)

Intarasiri, S.; Hallen, A.; Kamwanna, T.; Yu, L.D.; Possnert, G.; Singkarat, S.

2006-01-01

The ion beam synthesis (IBS) technique is applied to form crystalline silicon carbide (SiC) for future optoelectronics applications. Carbon ions at 80 and 40 keV were implanted into (1 0 0) high-purity p-type silicon wafers at room temperature and 400 deg. C, respectively, to doses in excess of 10 17 ions/cm 2 . Subsequent thermal annealing of the implanted samples was performed in a vacuum furnace at temperatures of 800, 900 and 1000 deg. C, respectively. Elastic recoil detection analysis was used to investigate depth distributions of the implanted ions and infrared transmittance (IR) measurement was used to characterize formation of SiC in the implanted Si substrate. Complementary to IR, Raman scattering measurements were also carried out. Levels of the residual damage distribution of the samples annealed at different temperatures were compared with that of the as-implanted one by Rutherford backscattering spectrometry (RBS) in the channeling mode. The results show that C-ion implantation at the elevated temperature, followed by high-temperature annealing, enhances the synthesis of crystalline SiC

Synthesis and characterization of thorium(IV) and uranium(IV) complexes with Schiff bases

Energy Technology Data Exchange (ETDEWEB)

Radoske, Thomas; Maerz, Juliane; Kaden, Peter; Patzschke, Michael; Ikeda-Ohno, Atsushi [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Chemistry of the F-Elements

2017-06-01

We report herein the synthesis and characterization of several imine complexes of tetravalent thorium (Th(IV)) and uranium (U(IV)). The ligands investigated in this study are a Schiff base type, including the well-known salen ligand (H{sub 2}Le, Fig. 1). The complexation in solution was investigated by NMR measurements indicating paramagnetic effects of unpaired f-electrons of U(IV) on the ligand molecule. We also determined the solid-state molecular structures of the synthesized complexes by single crystal X-ray diffraction. The synthesized complexes show an eight-fold coordination geometry around the actinide center surrounded by two tetradentate ligands with 2N- and 2O-donor atoms.

Synthesis, Characterization and Application of Multiscale Porous Materials

Energy Technology Data Exchange (ETDEWEB)

Hussami, Linda

2010-07-01

This thesis work brings fresh insights and improved understanding of nano scale materials through introducing new hybrid composites, 2D hexagonal in MCM-41 and 3D random interconnected structures of different materials, and application relevance for developing fields of science, such as fuel cells and solar cells. New types of porous materials and organometallic crystals have been prepared and characterized in detail. The porous materials have been used in several studies: as hosts to encapsulate metal-organic complexes; as catalyst supports and electrode materials in devices for alternative energy production. The utility of the new porous materials arises from their unique structural and surface chemical characteristics as demonstrated here using various experimental and theoretical approaches. New single crystal structures and arene-ligand exchange properties of f-block elements coordinated to ligand arene and halogallates are described in Paper I. These compounds have been incorporated into ordered 2D-hexagonal MCM-41 and polyhedral silica nano foam (PNF-SiO{sub 2}) matrices without significant change to the original porous architectures as described in Paper II and III. The resulting inorganic/organic hybrids exhibited enhanced luminescence activity relative to the pure crystalline complexes. A series of novel polyhedral carbon nano foams (PNF-C's) and inverse foams were prepared by nano casting from PNF-SiO{sub 2}'s. These are discussed in Paper IV. The synthesis conditions of PNF-C's were systematically varied as a function of the filling ratio of carbon precursor and their structures compared using various characterization methods. The carbonaceous porous materials were further tested in Paper V and VI as possible catalysts and catalyst supports in counter- and working electrodes for solar- and fuel cell applications

KO t Bu-Initiated Aryl C–H Iodination: A Powerful Tool for the Synthesis of High Electron Affinity Compounds

KAUST Repository

Shi, Qinqin

2016-03-21

An efficient iodination reaction of electron-deficient heterocycles is described. The reaction utilizes KOtBu as an initiator and likely proceeds by a radical anion propagation mechanism. This new methodology is particularly effective for functionalization of building blocks for electron transport materials. Its utility is demonstrated with the synthesis of a new perylenediimide-thiazole non-fullerene acceptor capable of delivering a power conversion efficiency of 4.5% in a bulk-heterojunction organic solar cell. © 2016 American Chemical Society.

Novel methylene bridged ethylenediamine-type ligands: Synthesis and spectral characterization

Directory of Open Access Journals (Sweden)

Mihajlović-Lalić Ljiljana E.

2014-01-01

Full Text Available Herein we report the synthesis of two new organic compounds, diisobutyl- and diisopentyl N,N′-methylene-(S,S-ethylenediamine-N,N′-di-2-(3-cyclohexylpropanoate. A one-pot procedure was carried out by adding the reducing agent and carbonyl compound into the methanol solution of the parent compounds (iso-butyl and iso-pentyl esters of (S,S-ethylenediamine-N,N′-di-2-(3-cyclohexylpropanoic acid in appropriate stoichiometric ratios. The compounds were fully characterized by infrared, ESI-MS, 1D (1H, 13C and 2D (COSY, HSQC, HMBC NMR spectroscopy and elemental analysis. The spectral data confirm the presence of -CH2- group introduced between nitrogen atoms of the ethylenediamine moiety revealing neutral form of potential bidentate ligand. [Projekat Ministarstva nauke Republike Srbije, br. 172035. The authors also acknowledge the support of the FP7 RegPot project FCUB ERA GA No. 256716. The EC does not share responsibility for the content of the article

Plasma-polymerized alkaline anion-exchange membrane: Synthesis and structure characterization

International Nuclear Information System (INIS)

Hu Jue; Meng Yuedong; Zhang Chengxu; Fang Shidong

2011-01-01

After-glow discharge plasma polymerization was developed for alkaline anion-exchange membranes synthesis using vinylbenzyl chloride as monomer. X-ray photoelectron spectroscopy and attenuated total reflection Fourier transform infrared spectroscopy were used to characterize the chemical structure properties of plasma-polymerized membranes. Ion-exchange capacities of quaternized poly(vinylbenzyl chloride) (QPVBC) membranes were measured to evaluate their capability of hydroxyl ion transport. A mechanism of plasma polymerization using VBC as monomer that accounts for the competitive effects of free radicals polymerization and plasma ablation in the plasma polymerization process was proposed. Our results indicate that plasma discharge power influences the contents of functional groups and the structure of the plasma polymer membranes, which attribute to the coactions of polymerization and ablation. The properties of uniform morphology, good adhesion to the substrate, high thermal stability and satisfying anion conduction level suggest the potential application of QPVBC membrane deposited at discharge power of 20 W in alkaline direct methanol fuel cells.

Synthesis and characterization of tricalcium phosphate ceramics doped with zinc

International Nuclear Information System (INIS)

Kai, K.C.; Marchi, J.; Ussui, V.; Bressiani, A.H.A.

2011-01-01

Due to its biocompatibility, the tricalcium phosphate (TCP) is used as a biomaterial for bone replacement and reconstruction. Zinc (Zn) can replace calcium in the crystal structure of TCP to be added in small quantities, can result in stimulatory effects on bone formation in vitro and in vivo. In this work, pure TCP and Zn-TCP, with general formula (Ca_1_-_xZn_x)_3 (PO_4)_2 and 0 ≤ x ≤ 0.0225, were prepared by wet synthesis, from precursors Ca(OH)_2, H_3PO_4 and ZnO, after calcinated at 800 deg C and characterized by X-ray diffraction, specific surface area, agglomerate size distribution, differential thermal analysis and scanning electron microscopy. The results showed that the addition of small amounts of Zn resulted in TCP with suitable densification and higher specific surface area, may be promising as biomaterial due to the stimulatory effects of zinc associated with suitable mechanical properties of the final material. (author)

Synthesis and Spectroscopic Characterization of Two Tetrasubstituted Cationic Porphyrin Derivatives

Directory of Open Access Journals (Sweden)

Newton M. Barbosa Neto

2011-07-01

Full Text Available An imidazolium tetrasubstituted cationic porphyrin derivative (the free base and its Zn(II complex with five-membered heterocyclic groups in the meso-positions were synthesized using microwave irradiation, and the compounds obtained characterized by 1H-NMR and mass spectrometry. We observed that under microwave irradiation the yield is similar to when the synthesis is performed under conventional heating, however, the time required to prepare the porphyrins decreases enormously. In order to investigate the electronic state of these compounds, we employed UV-Vis and fluorescence spectroscopy combined with quantum chemical calculations. The results reveal the presence, in both compounds, of a large number of electronic states involving the association between the Soret and a blue-shifted band. The Soret band in both compounds also shows a considerable solvent dependence. As for emission, these compounds present low quantum yield at room temperature and no solvent influence on the fluorescence spectra was observed.

Synthesis and characterization of nanocrystalline nuclear ceramics

International Nuclear Information System (INIS)

Ananthasivan, K.; Anthonysamy, S.; Chandramouli, V.; Vasudeva Rao, P.R.

2006-01-01

This paper highlights the utility of the gel-combustion synthesis in making solid solutions containing the oxides of U, Th, and Ce. The synthesis of a series of solid solutions of ceria with thoria and urania using the gel-combustion technique with citric acid as the fuel is presented as a typical case. The x-ray crystallite size, specific surface area, and residual carbon of the precursors and final products are discussed. The sinterability of these powders is analysed using their sintered densities. Solid solutions of thoria-ceria with a density higher than 85% TD (theoretical density) and those of urania ceria with a density as high as 96% TD were obtained. The microstructure of the thoria-ceria powders were analysed using high resolution electron microscopy. (author)

Synthesis and spectroscopic characterization of a fluorescent pyrrole derivative containing electron acceptor and donor groups

Science.gov (United States)

Almeida, A. K. A.; Monteiro, M. P.; Dias, J. M. M.; Omena, L.; da Silva, A. J. C.; Tonholo, J.; Mortimer, R. J.; Navarro, M.; Jacinto, C.; Ribeiro, A. S.; de Oliveira, I. N.

2014-07-01

The synthesis and fluorescence characterization of a new pyrrole derivative (PyPDG) containing the electron donor-acceptor dansyl substituent is reported. The effects of temperature and solvent polarity on the steady-state fluorescence of this compound are investigated. Our results show that PyPDG exhibits desirable fluorescent properties which makes it a promising candidate to be used as the photoactive material in optical thermometry and thermography applications. Further, the electrochemical and emission properties of polymeric films obtained from the oxidation polymerization of PyPDG are also analyzed.

Synthesis and characterization of monoclinic KGd(WO4)2 particles for non-cubic transparent ceramics

Science.gov (United States)

Thangaraju, D.; Durairajan, A.; Balaji, D.; Moorthy Babu, S.

2013-02-01

Monoclinic KGd(WO4)2 (KGW) particles were synthesized using polymeric metal complex sol-gel synthesis method. The derived particles were made as colloidal suspension form for better rotation of particles to have optimum response for applied magnetic field. The KGW fine particle suspension was prepared using electrostatic repulsion by electrolyte polymer. Prepared suspension was kept at 2 T and particles were settled using electrophoretic sedimentation using pH adjustment. The derived sediment was dried at 100 °C and the properties were characterized using XRD.

Novel Green Synthesis and Characterization of Nanopolymer ...

African Journals Online (AJOL)

Purpose: To develop a novel approach to green synthesis of nano-polymer porous gold ... underline their important uses in various fields ... enhances physical and chemical characteristics .... Nanoporous Materials: Science and Engineering.

Synthesis and characterization of nanometric magnetite coated by oleic acid and the surfactant CTAB

Energy Technology Data Exchange (ETDEWEB)

Celis, J. Almazán, E-mail: jony-jac-5@hotmail.com; Olea Mejía, O. F., E-mail: oleaoscar@yahoo.com [Universidad Autónoma del Estado de México, Centro Conjunto de Investigación en Química Sustentable UAEMéx-UNAM (Mexico); Cabral-Prieto, A., E-mail: agustin.cabral@inin.gob.mx; García-Sosa, I., E-mail: irma.garcia@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares (Mexico); Derat-Escudero, R., E-mail: escu@unam.mx [Instituto de Investigación de materiales de la UNAM (Mexico); Baggio Saitovitch, E. M., E-mail: esaitovitch@yahoo.com.br; Alzamora Camarena, M., E-mail: mariella.alzamora@gmail.com [Centro Brasileiro de Pesquizas Físicas (Brazil)

2017-11-15

Nanometric magnetite (nm-Fe{sub 3}O{sub 4}) particles were prepared by the reverse co-precipitation synthesis method, obtaining particle sizes that ranged from 4 to 8.5 nm. In their synthesis, the concentration of iron salts of ferric nitrate, Fe(NO{sub 3}){sub 3}⋅9H{sub 2}O, and ferrous sulfate, FeSO{sub 4}⋅7H{sub 2}O, were varied relative to the chemical reaction volume and by using different surfactants such as oleic acid (OA) and hexadecyltrimethylammonium bromide (CTAB). The nm-Fe{sub 3}O{sub 4} particles were characterized by transmission electron microscopy (TEM), Mössbauer spectroscopy (MS), magnetic and X-ray diffraction (XRD) measurements. Typical asymmetrical and/or broad lines shapes appeared in all Mössbauer spectra of the as prepared samples suggesting strong magnetic inter-particle interactions, reducing these interactions to some extent by gentle mechanical grinding. For the smallest particles, maghemite instead of magnetite was the main preparation product as low temperature Mössbauer and magnetic measurements indicated. For the intermediate and largest particles a mixture of magnetite and maghemite phases were produced as the saturation magnetization values of M{sub S} ∼ 60 emu/g indicated; these values were measured for most samples, independently of the coating surfactant concentration, and according to the ZFC-FC curves the blocking temperatures were 225K and 275K for the smallest and largest magnetite nanoparticles, respectively. The synthesis method was highly reproducible.

Study of the aqueous synthesis, optical and electrochemical characterization of alloyed Zn{sub x}Cd{sub 1-x}Te nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Matos, Charlene Regina Santos [Postgraduate Program in Materials Science and Engineering, Federal University of Sergipe, São Cristóvão, SE (Brazil); Candido, Luan P.M.; Souza, Helio Oliveira [Department of Chemistry, Federal University of Sergipe, São Cristóvão, SE (Brazil); Pereira da Costa, Luiz [Institute of Technology and Research (ITP), Tiradentes University, Aracaju, SE (Brazil); Sussuchi, Eliana Midori [Department of Chemistry, Federal University of Sergipe, São Cristóvão, SE (Brazil); Gimenez, Iara F., E-mail: gimenez@ufs.br [Postgraduate Program in Materials Science and Engineering, Federal University of Sergipe, São Cristóvão, SE (Brazil); Department of Chemistry, Federal University of Sergipe, São Cristóvão, SE (Brazil); Postgraduate Program in Chemistry, Federal University of Sergipe, São Cristóvão, SE (Brazil)

2016-08-01

The effects of experimental factors such as initial reaction pH, capping ligand, and heating method on the optical and electrochemical properties of aqueous alloyed Zn{sub x}Cd{sub 1-x}Te nanocrystals were evaluated. Here the type of capping ligand (glutathione GSH and 3-mercaptopropionic acid MPA) was found to be the most significant factor in controlling the range of photoluminescence emission. Also a pronounced pH effect on the emission wavelength has been verified in the presence of GSH, in contrast to MPA for which only a minor pH effect was observed. The heating method (microwave or hydrothermal) was found to be irrelevant for the emission wavelength at the conditions studied. The electrochemical characterization in aqueous medium (cyclic voltammetry and differential pulse voltammetry) evidenced a good correlation between electrochemical and optical band gap values and allowed estimation of band edge positions. - Highlights: • ZnCdTe quantum dots were obtained by aqueous synthesis. • Nature of capping ligand was the most relevant factor. • Optical and electrochemical band gaps were well correlated.

Synthesis and characterization of zeolite material from coal ashes modified by surfactant

International Nuclear Information System (INIS)

Fungaro, D.A.; Borrely, S.I.

2010-01-01

Coal ash was used as starting material for zeolite synthesis by means of hydrothermal treatment. The surfactant-modified zeolite (SMZ) was prepared by adsorbing the cationic surfactant hexadecyltrimethylammonium bromide (HDTMA-Br) on the external surface of the zeolite from coal ash. The zeolite structure stability was monitored during the characterization of the materials by FTIR, XDR and SEM. The structural parameters of surfactant-modified zeolite are very close to that of corresponding non-modified zeolite which indicates that the crystalline nature of the zeolite remained intact after required chemical treatment with HDTMA-Br molecules and heating treatment for drying. The most intense peaks in the FTIR spectrum of HDTMA-Br were observed in SMZ spectrum confirming adsorption of surfactant on zeolites. (author)

Synthesis and characterization of a novel meso-porphyrin and its metallo derivatives

Directory of Open Access Journals (Sweden)

Paulo Cesar Bega

2014-02-01

Full Text Available There has been a growing interest in the properties of substituted meso-tetraarylporphyrins and metallo porphyrins as catalysts for oxidation of hydrocarbons, oxygen detection, among others. This work describes the synthesis of a new porphyrin, 5,10,15,20-tetrakis(4-butoxy-3-methoxyphenylporphyrin, and its metallo complexes. Herein it was used a readily available reactant, vanillin, as starting material which was submitted to alkylation with n-bromobutane affording the synthetic precursor. The desired porphyrin was obtained by reacting the O-alkylated aldehyde with pyrrole in the presence of propionic acid (Alder-Longo method. The purified porphyrin was then subjected to the metallation process using iron (II and manganese (II salts. The synthesized compounds were characterized by IR, UV-Vis, NMR and EPR spectroscopy.

Synthesis and characterization of intercalated polyaniline-clay nanocomposite using supercritical CO2

Science.gov (United States)

Abdelraheem, A.; El-Shazly, A. H.; Elkady, M. F.

2018-05-01

Lately, supercritical CO2 (SCCO2) have been getting great interest. It can be used in numerous applications because it is environmentally friendly, safe, comparatively low cost, and nonflammable. One of its applications is being a solvent in the synthesis of polymeric-clay nanocomposite. In this paper, intercalated polyaniline-clay nanocomposite (PANC) was prepared using SCCO2. The intercalation structure of polyaniline chains between clay layers was verified by various characterization techniques. Scanning electron microscope and transmission electron microscope (SEM-TEM) were used to show the morphology of the synthesized nanocomposite. The molecular structure of PANC nanocomposite was confirmed using Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The BET surface area and the conductivity of the nanocomposite were determined.

Synthesis and molecular characterization of chitosan based polyurethane elastomers using aromatic diisocyanate.

Science.gov (United States)

Zia, Khalid Mahmood; Anjum, Sohail; Zuber, Mohammad; Mujahid, Muhammad; Jamil, Tahir

2014-05-01

The present research work was performed to synthesize a new series of chitosan based polyurethane elastomers (PUEs) using poly(ɛ-caprolactone) (PCL). The chitosan based PUEs were prepared by step-growth polymerization technique using poly(ɛ-caprolactone) (PCL) and 2,4-toluene diisocyanate (TDI). In the second step the PU prepolymer was extended with different mole ratios of chitosan and 1,4-butane diol (BDO). Molecular engineering was carried out during the synthesis. The conventional spectroscopic characterization of the synthesized samples using FT-IR confirms the existence of the proposed chitosan based PUEs structure. Internal morphology of the prepared PUEs was studied using SEM analysis. The SEM images confirmed the incorporation of chitosan molecules into the PU backbone. Copyright © 2014 Elsevier B.V. All rights reserved.

Synthesis, spectroscopic, biological activity and thermal characterization of ceftazidime with transition metals

Science.gov (United States)

Masoud, Mamdouh S.; Ali, Alaa E.; Elasala, Gehan S.; Kolkaila, Sherif A.

2018-03-01

Synthesis, physicochemical characterization and thermal analysis of ceftazidime complexes with transition metals (Cr(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Hg(II)) were discussed. It's obtained that ceftazidime act as bidentate ligand. From magnetic measurement and spectral data, octahedral structures were proposed for all complexes except for cobalt, nickel and mercury had tetrahedral structural. Hyper chemistry program confirmed binding sites of ceftazidime. Ceftazidime complexes show higher activity than ceftazidime for some strains. From TG and DTA curves the thermal decomposition mechanisms of ceftazidime and their metal complexes were suggested. The thermal decomposition of the complexes ended with the formation of metal oxides as a final product except in case of Hg complex.

Characterization of a eukaryotic translation initiation factor 5A homolog from Tamarix androssowii involved in plant abiotic stress tolerance

Directory of Open Access Journals (Sweden)

Wang Liuqiang

2012-07-01

Full Text Available Abstract Background The eukaryotic translation initiation factor 5A (eIF5A promotes formation of the first peptide bond at the onset of protein synthesis. However, the function of eIF5A in plants is not well understood. Results In this study, we characterized the function of eIF5A (TaeIF5A1 from Tamarix androssowii. The promoter of TaeIF5A1 with 1,486 bp in length was isolated, and the cis-elements in the promoter were identified. A WRKY (TaWRKY and RAV (TaRAV protein can specifically bind to a W-box motif in the promoter of TaeIF5A1 and activate the expression of TaeIF5A1. Furthermore, TaeIF5A1, TaWRKY and TaRAV share very similar expression pattern and are all stress-responsive gene that functions in the abscisic acid (ABA signaling pathway, indicating that they are components of a single regulatory pathway. Transgenic yeast and poplar expressing TaeIF5A1 showed elevated protein levels combined with improved abiotic stresses tolerance. Furthermore, TaeIF5A1-transformed plants exhibited enhanced superoxide dismutase (SOD and peroxidase (POD activities, lower electrolyte leakage and higher chlorophyll content under salt stress. Conclusions These results suggested that TaeIF5A1 is involved in abiotic stress tolerance, and is likely regulated by transcription factors TaWRKY and TaRAV both of which can bind to the W-box motif. In addition, TaeIF5A1 may mediate stress tolerance by increasing protein synthesis, enhancing ROS scavenging by improving SOD and POD activities, and preventing chlorophyll loss and membrane damage. Therefore, eIF5A may play an important role in plant adaptation to changing environmental conditions.

Characterization of a eukaryotic translation initiation factor 5A homolog from Tamarix androssowii involved in plant abiotic stress tolerance.

Science.gov (United States)

Wang, Liuqiang; Xu, Chenxi; Wang, Chao; Wang, Yucheng

2012-07-26

The eukaryotic translation initiation factor 5A (eIF5A) promotes formation of the first peptide bond at the onset of protein synthesis. However, the function of eIF5A in plants is not well understood. In this study, we characterized the function of eIF5A (TaeIF5A1) from Tamarix androssowii. The promoter of TaeIF5A1 with 1,486 bp in length was isolated, and the cis-elements in the promoter were identified. A WRKY (TaWRKY) and RAV (TaRAV) protein can specifically bind to a W-box motif in the promoter of TaeIF5A1 and activate the expression of TaeIF5A1. Furthermore, TaeIF5A1, TaWRKY and TaRAV share very similar expression pattern and are all stress-responsive gene that functions in the abscisic acid (ABA) signaling pathway, indicating that they are components of a single regulatory pathway. Transgenic yeast and poplar expressing TaeIF5A1 showed elevated protein levels combined with improved abiotic stresses tolerance. Furthermore, TaeIF5A1-transformed plants exhibited enhanced superoxide dismutase (SOD) and peroxidase (POD) activities, lower electrolyte leakage and higher chlorophyll content under salt stress. These results suggested that TaeIF5A1 is involved in abiotic stress tolerance, and is likely regulated by transcription factors TaWRKY and TaRAV both of which can bind to the W-box motif. In addition, TaeIF5A1 may mediate stress tolerance by increasing protein synthesis, enhancing ROS scavenging by improving SOD and POD activities, and preventing chlorophyll loss and membrane damage. Therefore, eIF5A may play an important role in plant adaptation to changing environmental conditions.

Low temperature synthesis and characterization of Na–M–(O)–F phases with M=Ti, V

Energy Technology Data Exchange (ETDEWEB)

Nava-Avendaño, Jessica [Institut de Ciència de Materials de Barcelona (ICMAB-CSIC), Campus UAB, E-08193 Bellaterra, Catalonia (Spain); Ayllón, José A. [Departament de Química, Universitat Autònoma de Barcelona, Campus UAB, E-08193 Bellaterra, Catalonia (Spain); Frontera, Carlos; Oró-Solé, Judith [Institut de Ciència de Materials de Barcelona (ICMAB-CSIC), Campus UAB, E-08193 Bellaterra, Catalonia (Spain); Estruga, Marc [Departament de Química, Universitat Autònoma de Barcelona, Campus UAB, E-08193 Bellaterra, Catalonia (Spain); Molins, Elies [Institut de Ciència de Materials de Barcelona (ICMAB-CSIC), Campus UAB, E-08193 Bellaterra, Catalonia (Spain); Palacín, M. Rosa, E-mail: rosa.palacin@icmab.es [Institut de Ciència de Materials de Barcelona (ICMAB-CSIC), Campus UAB, E-08193 Bellaterra, Catalonia (Spain)

2015-03-15

Na{sub 5}Ti{sub 3}O{sub 3}F{sub 11} was prepared by the microwave assisted method, and presents a chiolite related structure with cell parameters a=10.5016(5), b=10.4025(5), and c=10.2911(5) Å and Cmca (no. 64) space group. From solvothermal synthesis at 100 °C the cryolite Na{sub 3−δ}VO{sub 1−δ}F{sub 5+δ} was prepared, which crystallizes in the monoclinic system with a=5.5403(2), b=5.6804(2), c=7.9523(2) Å, β=90.032(7)° cell parameters and P2{sub 1}/n (no. 14) space group. Under similar synthesis conditions but with higher HF concentration the chiolite-type phase Na{sub 5−δ}V{sub 3}F{sub 14} was achieved, which exhibits a=10.5482(2), b=10.4887(1) and c=10.3243(1) Å cell parameters and Cmc2{sub 1} (no. 36) space group. A single crystal also having the chiolite structure was synthesized at 200 °C which exhibits tetragonal symmetry (a=7.380(3) and c=10.381(11) Å and space group P4{sub 2}2{sub 1}2 (no. 94)). Bond valence sum indicates that it contains V{sup 4+} and therefore can be formulated as Na{sub 5}V{sub 3}O{sub 3}F{sub 11}. - Graphical abstract: Na{sub 5}M{sub 3}(O,F){sub 14} with M=Ti and V having chiolite structure and Na{sub 3−δ}VO{sub 1−δ}F{sub 5+δ} cryolite were prepared by means of microwave-assisted and solvothermal synthesis. - Highlights: • Na{sub 5}Ti{sub 3}O{sub 3}F{sub 11} chiolite was prepared by a microwave assisted method and characterized. • Na{sub 3−δ}VO{sub 1−δ}F{sub 5+δ} and Na{sub 5−δ}V{sub 3}F{sub 14} were prepared by solvothermal synthesis. • The compounds were structurally characterized by diffraction techniques. • O/F distribution was estimated by applying Pauling’s second rule.

Synthesis and characterization of nanocomposite powders of calcium phosphate/silica-gel; Sintese e caracterizacao de pos nanoestruturados de fosfato de calcio/silica-gel

Energy Technology Data Exchange (ETDEWEB)

Muller, D.T.; Delima, S.A. [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Dept. de Engenharia Mecanica; Santos, R.B.M.; Camargo, N.H.A., E-mail: dem2nhac@joinville.udesc.b [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Programa de Pos Graduacao em Ciencia e Engenharia de Materiais

2009-07-01

In the recent years ceramics of calcium phosphate are pointed out as an outstanding material in substitution and regeneration in defects from osseous tissue, in reason of their similar mineralogical characteristics of apatite of bone structure. However, the challenge with phosphate calcium ceramics find out about the mechanical properties and the development of biomaterials similar of the bone structure, what sometimes is not so easy, about fragile materials. The aim of this work focused in synthesis and characterization nanocomposites powders of calcium phosphate/silica-gel with percentages 1, 2, 3 e 5% of nanometric silica. The method synthesis used for the compositions elaboration was dissolution-precipitation. The presented results are related with the optimization to method elaboration of nanostructured powders, the mineralogical characterization with X-ray diffraction, thermal behavior with thermal differential analysis, differential scanning calorimetry here is ADT and dilatometer. The scanning electronic microscopy was used to help of morphological characterization the nanostructured powders and the surfaces from body test recovered from the mechanical test. (author)

Synthesis and characterization of In{sub 2}O{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Ayeshamariam, A. [KhadirMohideen College, Adirampattinam (India); Kashif, M. [Universiti Malaysia Perlis, Perlis (Malaysia); Raja, S. Muthu [Vellore Institute of Technology, Vellore (India); Sivaranjani, S. [SBM College of Engineering and technology, Dindigul (India); Sanjeeviraja, C. [Alagappa University, Karaikudi (India); Bououdina, M. [University of Bahrain, Bahrain (Bahrain)

2014-01-15

Metal-oxide nanostructures have elicited increasing interest in both fundamental and applied sciences. Among metal oxide nanostructures, In{sub 2}O{sub 3} has the potential for use asa semiconductor material. This article provides details on studies carried out thus far for the synthesis and the characterization of In{sub 2}O{sub 3} nanostructures. In this research, various techniques were investigated for the fabrication of diverse and fascinating spherical shaped In{sub 2}O{sub 3} nanostructures. BrunauerEmmett-Teller (BET) analyses of the In{sub 2}O{sub 3} nanostructures through detailed refinements of the structure of the In{sub 2}O{sub 3} nanoparticles by using the Rietveld method, followed by microstructural analyses using scanning electron microscopy/ transmission electron microscopy (SEM/TEM) and a chemical composition analysis are presented and discussed. Decreasing crystallinity with an improvement in specific surface area was observed from the structural characterization. The energy dispersive analysis results showed that the as-prepared In{sub 2}O{sub 3} powder sample was stoichiometric, containing almost equal proportions of indium and oxygen. The microstructural analysis (TEM and SEM) demonstrated precise control over the diameters of the nanoparticles, which is an important advantage of the solution combustion approach.

Synthesis and characterization of carbon nanotube from coconut shells activated carbon

Science.gov (United States)

Melati, A.; Hidayati, E.

2016-03-01

Carbon nanotubes (CNTs) have been explored in almost every single cancer treatment modality, including drug delivery, lymphatic targeted chemotherapy, photodynamic therapy, and gene therapy. They are considered as one of the most promising nanomaterial with the capability of both detecting the cancerous cells and delivering drugs or small therapeutic molecules to the cells. CNTs have unique physical and chemical properties such as high aspect ratio, ultralight weight, high mechanical strength, high electrical conductivity, and high thermal conductivity. Coconut Shell was researched as active carbon source on 500 - 600°C. These activated carbon was synthesized becomes carbon nanotube and have been proposed as a promising tool for detecting the expression of indicative biological molecules at early stage of cancer. Clinically, biomarkers cancer can be detected by CNT Biosensor. We are using pyrolysis methods combined with CVD process or Wet Chemical Process on 600°C. Our team has successfully obtained high purity, and aligned MWCNT (Multi Wall Nanotube) bundles on synthesis CNT based on coconut shells raw materials. CNTs can be used to cross the mammalian cell membrane by endocytosis or other mechanisms. SEM characterization of these materials have 179 nm bundles on phase 83° and their materials compound known by using FTIR characterization.

Synthesis and Characterization of Allophane-Like as Chromium (Cr) Ion Adsorbent

Science.gov (United States)

Pranoto; Purnawan, C.; Husnina, A. N.

2018-03-01

The synthesis and characterization of allophane-like as chrom (Cr) ion adsorbent has been studied. The objectives of this study is to determine the characteristics of allophane-like and determine ratio of Al/Si, chromium solution pH, and contact time to get the best decreasing metal ion chrom (Cr) adsorption condition. The study was conducted with the ratio of Al/Si ratios 0.5; 0.75; 1.0; 1.25 and 1.5 from Tetraetyl Orthosilicate (TEOS) solution and Aluminium Nitrate Nonahydrate [Al(NO3)3.9H2O] in pH 3-4. The result of synthetic was characterized on functional groups and cristallinity. Experiment of adsorption ability using variation of Cr solution pH 3-7, contact time 30, 60, 90 and 120 minutes with batch method. The results by FTIR shows that functional groups-OH, the asymmetry groups O-Si-O or O-Al-O, relatively weak absorption which stronger then the presence of OH and bending vibration Si-O or Al-O on allophane-like. The best conditions of chromium metal adsorption with adsorbent allophane-like was obtained at pH 5, contact time 90 minutes, and the ratio Al/Si 1.5. Types of adsorption in this study follows Freundlich and Langmuir isotherm.

Synthesis and characterization of KY3F10 and KY3F10:Yb:Nd:Tm crystals for optical applications

International Nuclear Information System (INIS)

Linhares, Horacio Marconi da Silva Dantas

2009-01-01

In this work, crystals of KY 3 F 10 pure and doped with Yb, Nd and Tm were grown aiming at the attainment of blue emission via Tm 3+ ions up conversion. It was established the best conditions to synthesis and purification of KY 3 F 10 . Crystals doped with 1.3 mol% Nd, 0.5 mol% Tm and some concentrations of Yb (5, 10, 20, 30 and 40 mol%) were obtained by slow cooling of the charge from the melt, using an usual conventional synthesis system and in a reactive HF atmosphere. It was taken into account parameters as cooling rate and different configurations of boats to conditioning the materials. The limit of Yb concentration to obtain a unique cubic phase was determined as 30mol%, for the cooling rates used in this work. The physical and chemical characterizations of the samples were performed by X-ray diffraction, differential thermal analysis, inductively coupled plasma-optical emission spectroscopy (ICP-OES), scanning electron microscopy, optical absorption and emission. An initial spectroscopic study was performed to verify the effect of the Yb 3+ concentration regarding the blue emission efficiency in the KY 3 F 10 :Yb:Nd:Tm. When the Nd 3+ is pumped at 797 nm, it was determined that the suitable Yb concentrations are between 10 and 20 mol% to obtain blue emission at 480 nm, and between 20 and 30 mol% to obtain emission at 450 nm. It was observed that two emissions bands in the UV (350 and 360nm) enhanced proportionally with the Yb 3+ concentration. (author)

Characterization of a 1,4-. beta. -D-glucan synthase from Dictyostelium discoideum

Energy Technology Data Exchange (ETDEWEB)

Blanton, R.L.

1992-01-15

Various aspects of research concerning Dictyostelium discoideum are presented. The initial focus of this project was upon: the characterization of potential probes for the cellulose synthase (antibody and nucleic acid), the determination of the cultural induction conditions of cellulose synthesis, the solubilization of the enzyme activity, the development of a non-inhibitory disruption buffer, the generation and isolation of mutant strains deficient in cellulose synthesis, and the development of the capability to determine the degree of polymerization of the in vitro product. I have briefly summarized our most significant findings with only selected data sets being shown in this report in the interest of brevity.

Novel metallomesogenic polyurethanes: Synthesis, characterization and properties

International Nuclear Information System (INIS)

Senthilkumar, Natarajan; Narasimhaswamy, Tanneru; Kim, Il-Jin

2012-01-01

A series of tetradentate Schiff base metallomesogenic diols were synthesized from two simple dihydroxy benzenes. The metallomesogenic diol was constructed from three ring containing mesogen linked through ester and azomethine with terminal hydroxy group. This upon complexation with copper(II) formed metallomesogenic diol with varying terminal chain length. A series of metallomesogenic polyurethanes were synthesized using these metallomesogenic diols as chain extenders for the prepolymers based on polytetramethylene glycol (PTMG) of varying molecular weight (M n = 650, 2000) and 2,4-toluene diisocyanate (TDI), or 4,4′-methylene bis(phenyl isocyanate) (MDI). The molar ratio of metallomesogenic diol and PTMG were varied in the polyurethane to find their role in liquid crystalline and mechanical properties. Extensive characterization of all metallomesogenic compounds and intermediates were carried out by FT-IR, 1 H and 13 C NMR, EPR, VSM, Mass (EI and FAB) and UV–visible spectroscopy. Hot stage polarizing microscope and differential scanning calorimetry were used to ensure the phase characteristics such as nature of phase, melting and clearing temperatures and phase range. The appearance of enantiotropic smectic A phases indicated high molecular polarizability of the core due to the metal ion. - Highlights: ► Design and synthesis of metallomesogenic diols. ► Metallomesogenic polyurethanes were prepared using these diols as chain extenders. ► Liquid crystalline and mechanical properties were studied. ► A square pyramidal structure for the copper(II) complexes have been proposed. ► Polyurethanes exhibited enantiotropic smectic A phases.

Sequential infiltration synthesis for advanced lithography

Energy Technology Data Exchange (ETDEWEB)

Darling, Seth B.; Elam, Jeffrey W.; Tseng, Yu-Chih; Peng, Qing

2017-10-10

A plasma etch resist material modified by an inorganic protective component via sequential infiltration synthesis (SIS) and methods of preparing the modified resist material. The modified resist material is characterized by an improved resistance to a plasma etching or related process relative to the unmodified resist material, thereby allowing formation of patterned features into a substrate material, which may be high-aspect ratio features. The SIS process forms the protective component within the bulk resist material through a plurality of alternating exposures to gas phase precursors which infiltrate the resist material. The plasma etch resist material may be initially patterned using photolithography, electron-beam lithography or a block copolymer self-assembly process.

Phosphine-free synthesis and characterization of type-II ZnSe/CdS core-shell quantum dots

Science.gov (United States)

Ghasemzadeh, Roghayyeh; Armanmehr, Mohammad Hasan; Abedi, Mohammad; Fateh, Davood Sadeghi; Bahreini, Zaker

2018-01-01

A phosphine-free route for synthesis of type-II ZnSe/CdS core-shell quantum dots, using green, low cost and environmentally friendly reagents and phosphine-free solvents such as 1-octadecene (ODE) and liquid paraffin has been reported. Hot-injection technique has been used for the synthesis of ZnSe core quantum dots. The CdS shell quantum dots prepared by reaction of CdO precursor and S powder in 1-octadecene (ODE). The ZnSe/CdS core-shell quantum dots were synthesized via successive ion layer adsorption and reaction (SILAR) technique. The characterization of produced quantum dots were performed by absorption and fluorescence spectroscopy, X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX) and transmission electron microscopy (TEM). The results showed the formation of type-II ZnSe/CdS core-shell quantum dots with FWHM 32 nm and uniform size distribution.

Synthesis, characterization and catalytic activity of stable [(NHC)H][ZnXY2] (NHC=N-Heterocyclic carbene, X, Y=Cl, Br) species

KAUST Repository

Santoro, Orlando; Nahra, Fady; Cordes, David B.; Slawin, Alexandra M.Z.; Nolan, Steven P.; Cazin, Catherine S. J.

2016-01-01

The synthesis and characterization of imidazol(in)ium-based zinc(II) halide salts are reported. These compounds present interesting structural features and exhibit high stability. Their catalytic activity was explored in the methylation of amines with CO2 and PhSiH3.

Synthesis, characterization and catalytic activity of stable [(NHC)H][ZnXY2] (NHC=N-Heterocyclic carbene, X, Y=Cl, Br) species

KAUST Repository

Santoro, Orlando

2016-06-04

The synthesis and characterization of imidazol(in)ium-based zinc(II) halide salts are reported. These compounds present interesting structural features and exhibit high stability. Their catalytic activity was explored in the methylation of amines with CO2 and PhSiH3.

Synthesis and Characterization of Furanic Compounds

Science.gov (United States)

2013-09-01

Furanamine. Solvent 2-Furanamine Acetone — Chloroform — Dimethylacetamide (DMAc) — Dimethylsulfoxide ( DMSO ) + Methanol ± Tetrahydrofuran (THF...4 Figure 4. 1 H NMR of 2-Furanamine in D2O solvent ...Spectra for the furanic compounds were obtained in a 0.1%–0.5% deuterated solvent solutions. 3. Synthesis 3.1 General The following monomers and

Ultrafine Magnetite Nanopowder: Synthesis, Characterization, and Preliminary Use as Filler of Polymethylmethacrylate Nanocomposites

Directory of Open Access Journals (Sweden)

Pietro Russo

2012-01-01

Full Text Available Magnetite (Fe3O4 nanoparticles prepared by microwave-assisted hydrothermal synthesis have been characterized in terms of morphological and structural features. Electron micrographs collected in both scanning (SEM and transmission (TEM modes and evaluations of X-ray powder diffraction (XRD patterns have indicated the achievement of a monodispersed crystallite structure with particles having an average size around 15–20 nm. Structural investigations by Micro-Raman spectroscopy highlighted the obtainment of magnetite nanocrystals with a partial surface oxidation to maghemite (γ-Fe3O4. Preliminary attention has been also paid to the use of these magnetite nanoparticles as filler for a commercial polymethylmethacrylate resin. Hybrid formulations containing up to 3 wt% of nanoparticles were prepared by melt blending and characterized by calorimetric and thermogravimetric tests. For sake of comparison, same formulations containing commercial Fe3O4 nanoparticles are also reported. Calorimetric characterization indicates an increase of both glass transition temperature and thermal stability of the nanocomposite systems when loaded with the synthesized magnetite nanoparticles rather then loaded with the same amount of commercial Fe3O4. This first observation represents just one aspect of the promising potentiality offered by the novel magnetic nanoparticles when mixed with PMMA.

High-throughput synthesis equipment applied to polymer research

NARCIS (Netherlands)

Hoogenboom, R.; Schubert, U.S.

2005-01-01

To speed up synthetic polymer research, a workflow dedicated to automated polymer synthesis and characterization was developed. The workflow consists of several synthesis robots with online and offline analytical equipment. For screening of reaction parameters and for library synthesis, robots

Synthesis of poly(D,L-lactide-co-glycolide) copolymers and its chemical characterization by NMR and FTIR; Sintese e caracterizacao quimica por RMN e FTIR do copolimero poli(D,L-lactideo-co-glicolideo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

Poly(D,L-lactide-co-glycolide) copolymer is of great interest for medical applications. This interest is justified by the fact that it is bioreabsorbable, biocompatible and non-toxic, while its degradation kinetics can be modified by the copolymerization ratio of the monomers. In this study, copolymers were synthesized at 175 deg C by opening the rings of the cyclic dimers of the D,L-lactide and glycolide monomers in the presence of stannous octoate initiator and lauryl alcohol co-initiator. The efficient application of a vacuum to the reaction medium, coupled with adequate stirring, is fundamental for the success of the synthesis. The following analysis techniques were used to characterize the synthesized copolymers: Nuclear Magnetic Resonance Spectroscopy (NMR) and Fourier Transform Infrared Spectroscopy (FTIR). The chemical composition and the ratio of the monomers in the synthesized copolymer were determined. (author)

Synthesis, characterization and mechanistic insights of mycogenic iron oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Bhargava, Arpit; Jain, Navin; Manju Barathi L [Birla Institute of Technology and Science, Centre for Biotechnology, Department of Biological Sciences (India); Akhtar, Mohd Sayeed [Jimma University, Department of Applied Microbiology, College of Natural Sciences (Ethiopia); Yun, Yeoung-Sang [Chonbuk National University, Division of Environmental and Chemical Engineering (Korea, Republic of); Panwar, Jitendra, E-mail: drjitendrapanwar@yahoo.co.in [Birla Institute of Technology and Science, Centre for Biotechnology, Department of Biological Sciences (India)

2013-11-15

In the present study, extracellular synthesis of iron oxide nanoparticles (IONPs) was achieved using Aspergillus japonicus isolate AJP01. The isolate demonstrated its ability to hydrolyze the precursor salt solution, a mixture of iron cyanide complexes, under ambient conditions. Hydrolysis of these complexes released ferric and ferrous ions, which underwent protein-mediated coprecipitation and controlled nucleation resulting in the formation of IONPs. Transmission electron microscopy, selected area electron diffraction pattern, energy dispersive spectroscopy and grazing incidence X-ray diffraction analysis confirmed the mycosynthesis of IONPs. The synthesized particles were cubic in shape with a size range of 60–70 nm with crystal structure corresponding to magnetite. Scanning electron microscopy analysis revealed the absence of IONPs on fungal biomass surface, indicating the extracellular nature of synthesis. Fourier transform infrared spectroscopy confirmed the presence of proteins on as-synthesised IONPs, which may confer their stability. Preliminary investigation indicated the role of proteins in the synthesis and stabilization of IONPs. On the basis of present findings, a probable mechanism for synthesis of IONPs is suggested. The simplicity and versatility of the present approach can be utilized for the synthesis of other nanomaterials.

Microwave Synthesis and Characterization of Waste Soybean Oil-Based Gemini Imidazolinium Surfactants with Carbonate Linkage

Science.gov (United States)

Tripathy, Divya Bajpai; Mishra, Anuradha

Gemini surfactants are presently gaining attention due to their unusual self-assembling characteristics and incomparable interfacial activity. Current research work involves the cost-effective microwave (MW) synthesis of waste soybean oil-based gemini imidazolinium surfactants (GIS) having a carbonate linkage in its spacer moiety. Structural characterizations of the materials have been done using FT-IR, 1H-NMR and 13C-NMR. Using indigenous and natural material as base and MW as energy source for synthesizing the GIS with easily degradable chemical moiety make them to be labeled as green surfactants.

Synthesis and Characterization of Polyfunctional Polyhedral Silsesquioxane Cages

Science.gov (United States)

Sulaiman, Santy

Recent studies on octameric polyhedral silsesquioxanes, (RSiO1.5 )8, indicate that the silsesquioxane cage is not just a passive component but appears to be involved in electron delocalization with conjugated organic tethers in the excited state. This dissertation presents the synthesis and characterization of (RSiO1.5)8 molecules with unique photophysical properties that provide support for the existence of conjugation that involves the (RSiO1.5)8 cage. The dissertation first discusses the elaboration of octavinylsilsesquioxane via cross-metathesis to form styrenyl-functionalized octasilsesquioxane molecules. Subsequent Heck coupling reactions of p-bromostyrenyl derivative provides vinylstilbene-functionalized octasilsesquioxane. The amino derivative, NH2VinylStilbeneOS, show highly red-shifted emission spectrum (100 nm from the simple organic analog p-vinylstilbene) and high two-photon absorption (TPA) cross-section value (100 GM/moiety), indicating charge-transfer processes involving the silsesquioxane cage as the electron acceptor. The unique photophysical properties of polyfunctional luminescent cubic silsesquioxanes synthesized from ortho-8-, (2,5)-16-, and 24-brominated octaphenylsilsesquioxane (OPS) via Heck coupling show how the steric interactions of the organic tethers at the silsesquioxane cage corner affect conjugation with the silsesquioxane cage. Furthermore, the high TPA cross-section (10 GM/moiety) and photoluminescence quantum yield (20%) of OPS functionalized with 24 acetoxystyrenyl groups suggest that the existence excited states in these molecules with similar energies and decay rates: normal radiative pi- pi* transition and charge transfer involving the silsesquioxane cage. The fluoride ion-catalyzed rearrangement reactions of cage and polymeric silsesquioxanes provide a convenient route to a mixture of deca- and dodecameric silsesquioxane molecules in high yields, giving us the opportunity to investigate the effect of silsesquioxane cage

Synthesis and Characterization of Chemically Etched Nanostructured Silicon

KAUST Repository

Mughal, Asad Jahangir

2012-05-01

Silicon is an essential element in today’s modern world. Nanostructured Si is a more recently studied variant, which has currently garnered much attention. When its spatial dimensions are confined below a certain limit, its optical properties change dramatically. It transforms from an indirect bandgap material that does not absorb or emit light efficiently into one which can emit visible light at room temperatures. Although much work has been conducted in understanding the properties of nanostructured Si, in particular porous Si surfaces, a clear understanding of the origin of photoluminescence has not yet been produced. Typical synthesis approaches used to produce nanostructured Si, in particular porous Si and nanocrystalline Si have involved complex preparations used at high temperatures, pressures, or currents. The purpose of this thesis is to develop an easier synthesis approach to produce nanostructured Si as well as arrive at a clearer understanding of the origin of photoluminescence in these systems. We used a simple chemical etching technique followed by sonication to produce nanostructured Si suspensions. The etching process involved producing pores on the surface of a Si substrate in a solution containing hydrofluoric acid and an oxidant. Nanocrystalline Si as well as nanoscale amorphous porous Si suspensions were successfully synthesized using this process. We probed into the phase, composition, and origin of photoluminescence in these materials, through the use of several characterization techniques. TEM and SEM were used to determine morphology and phase. FT-IR and XPS were employed to study chemical compositions, and steady state and time resolved optical spectroscopy techniques were applied to resolve their photoluminescent properties. Our work has revealed that the type of oxidant utilized during etching had a significant impact on the final product. When using nitric acid as the oxidant, we formed nanocrystalline Si suspensions composed of

Microwave radiation hydrothermal synthesis and characterization of micro- and mesoporous composite molecular sieve Y/SBA-15

Directory of Open Access Journals (Sweden)

Wenyuan Wu

2017-05-01

Full Text Available A microwave radiation hydrothermal method to control synthesis of micro- and mesoporous Y/SBA-15 composite molecular sieves was reported. The synthesized SBA-15 and Y/SBA-15 were characterized by scanning electron microscopy (SEM and N2 adsorption–desorption. The three kinds of different concentrations of hydrochloric acid (0.75 M, 2 M and 3.25 M were used to investigate the effect on Y/SBA-15. The analysis results of the composite products indicated that the optimization synthesis condition employed zeolite type Y and TEOS as silicon sources under 0.75 M hydrochloric acid by the microwave radiation hydrothermal synthesis method. The N2 adsorption–desorption test results of micro–mesoporous composite molecular sieve type Y/SBA-15 in mesoporous extent indicated that SBET is 355.529 m2/g, D‾BET is 4.050 nm, and mesoporous aperture focuses on the distribution region of 5.3 nm. It was found that the received composite product has an appropriate proportion of smaller size, larger size pore structure and the thicker pore wall. In addition, its internal channels have a high degree of order and smooth flow in long-range channels.

Synthesis and structural characterization of bulk Sb2Te3 single crystal

Science.gov (United States)

Sultana, Rabia; Gahtori, Bhasker; Meena, R. S.; Awana, V. P. S.

2018-05-01

We report the growth and characterization of bulk Sb2Te3 single crystal synthesized by the self flux method via solid state reaction route from high temperature melt (850˚C) and slow cooling (2˚C/hour) of constituent elements. The single crystal X-ray diffraction pattern showed the 00l alignment and the high crystalline nature of the resultant sample. The rietveld fitted room temperature powder XRD revealed the phase purity and rhombohedral structure of the synthesized crystal. The formation and analysis of unit cell structure further verified the rhombohedral structure composed of three quintuple layers stacked one over the other. The SEM image showed the layered directional growth of the synthesized crystal carried out using the ZEISS-EVOMA-10 scanning electron microscope The electrical resistivity measurement was carried out using the conventional four-probe method on a quantum design Physical Property Measurement System (PPMS). The temperature dependent electrical resistivity plot for studied Sb2Te3 single crystal depicts metallic behaviour in the absence of any applied magnetic field. The synthesis as well as the structural characterization of as grown Sb2Te3 single crystal is reported and discussed in the present letter.

Thermal and mineralogical characterization of drill cuttings from north capixaba: initial studies

International Nuclear Information System (INIS)

Fialho, P.F.; Goncalves, G. dos R.; Calmon, J.L.; Tristao, F.A.; Nunes, E.; Cunha, A.G.

2011-01-01

The drilling of oil wells generates various wastes among which are the cuttings and drilling fluids. The management of these wastes have been a problem for the oil and gas industry because of the amount generated and its contaminants, which can be organic and inorganic. This paper presents initial studies of thermal and mineralogical characterization of the drill cuttings from oil wells and gas in Southeast Brazilian, state of Espirito Santo with aim of reuse them as raw material in building materials. Characterizations were performed physical, thermal and mineralogical by particle size distribution, thermogravimetric analysis, differential scanning calorimetry and X-ray diffraction. The results indicate that there are potential replacements of natural raw materials or drill cuttings in the production of building materials. (author)

Design, Synthesis and Characterization of Polyethylene-Based Macromolecular Architectures by Combining Polyhomologation with Powerful Linking Chemistry

KAUST Repository

Alkayal, Nazeeha

2016-09-05

Polyhomologation is a powerful method to prepare polyethylene-based materials with controlled molecular weight, topology and composition. This dissertation focuses on the discovery of new synthetic routes to prepare polyethylene-based macromolecular architectures by combining polyhomologation with highly orthogonal and efficient linking reactions such as Diels Alder, copper-catalyzed azide-alkyne cycloaddition (CuAAC), and Glaser. Taking advantage of functionalized polyhomologation initiators, as well as of the efficient coupling chemistry, we were able to synthesize various types of polymethylene (polyethylene)-based materials with complex architectures including linear co/terpolymers, graft terpolymers, and tadpole copolymers. In the first project, a facile synthetic route towards well-defined polymethylene-based co/terpolymers, by combining the anthracene/maleimide Diels–Alder reaction with polyhomologation, is presented. For the synthesis of diblock copolymers the following approach was applied: (a) synthesis of α-anthracene-ω-hydroxy-polymethylene by polyhomologation using tri (9 anthracene-methyl propyl ether) borane as the initiator, (b) synthesis of furan-protected-maleimide-terminated poly(ε-caprolactone) or polyethylene glycol and (c) Diels–Alder reaction between anthracene and maleimide-terminated polymers. In the case of triblock terpolymers, the α-anthracene-ω-hydroxy polymethylene was used as a macroinitiator for the ring-opening polymerization of D, L-lactide to afford an anthracene-terminated PM-b-PLA copolymer, followed by the Diels–Alder reaction with furan-protected maleimide-terminated poly (ε-caprolactone) or polyethylene glycol to give the triblock terpolymers. The synthetic methodology is general and potentially applicable to a range of polymers. The coupling reaction applied in the second project of this dissertation was copper-catalyzed “click” cycloaddition of azides and alkynes (CuAAC). Novel well-defined polyethylene

Synthesis and reactivity of dimethyl gold complexes supported on MgO: characterization by infrared and X-ray absorption spectroscopies

NARCIS (Netherlands)

Guzman, J.; Anderson, B.G.; Vinod, C.P.; Ramesh, K.; Niemantsverdriet, J.W.; Gates, B.C.

2005-01-01

Di-Me gold complexes bonded to partially dehydroxylated MgO powder calcined at 673 K were synthesized by adsorption of Au(CH3)2(acac) (acac is C5H7O2) from n-pentane soln. The synthesis and subsequent decompn. of the complexes by treatment in He or H2 were characterized with diffuse reflectance

Synthesis and characterization of Tin / Titanium mixed oxide nanoparticles doped with lanthanide for biomarking

International Nuclear Information System (INIS)

Paganini, Paula Pinheiro

2012-01-01

This work presents the synthesis, characterization and photo luminescent study of tin and titanium mixed oxide nanoparticles doped with europium, terbium and neodymium to be used with luminescent markers on biological systems. The syntheses were done by co-precipitation, protein sol-gel and Pechini methods and the nanoparticles were characterized by infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, X-ray diffraction and X-ray absorption spectroscopy. The photo luminescent properties studies were conducted for luminophores doped with europium, terbium and neodymium synthesized by coprecipitation method. For luminophore doped with europium it was possible to calculate the intensity parameters and quantum yield and it showed satisfactory results. In the case of biological system marking it was necessary the functionalization of these particles to allow them to bind to the biological part to be studied. So the nanoparticles were functionalized by microwave and Stöber methods and characterized by infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction obtaining qualitative response of functionalization efficacy. The ninhydrin spectroscopic method was used for quantification of luminophores functionalization. The photo luminescent studies of functionalized particles demonstrate the potential applying of these luminophores as luminescent markers. (author)

Synthesis and characterization of porous metal oxides and desulfurization studies of sulfur containing compounds

Science.gov (United States)

Garces Trujillo, Hector Fabian

This thesis contains two parts: 1) synthesis and characterization of porous metal oxides that include zinc oxide and a porous mixed-valent manganese oxide with an amorphous structure (AMO) 2) the desulfurization studies for the removal of sulfur compounds. Zinc oxide with different nano-scale morphologies may result in various porosities with different adsorption capabilities. A tunable shape microwave synthesis of ZnO nano-spheres in a co-solvent mixture is presented. The ZnO nano-sphere material is investigated as a desulfurizing sorbent in a fixed bed reactor in the temperature range 200 to 400 °C and compared with ZnO nanorods and platelet-like morphologies. Fresh and sulfided materials were characterized by X-ray diffraction (XRD), BET specific surface area, pore volume, scanning electron microscopy (SEM), X-ray energy dispersive spectroscopy (SEM/EDX), Raman spectroscopy, and thermogravimetric analysis (TGA). The tunable shape microwave synthesis of ZnO presents a high sulfur sorption capacity at temperatures as low as 200 °C which accounts for a three and four fold enhancement over the other preparations presented in this work, and reached 76 % of the theoretical sulfur capacity (TSC) at 300 °C. Another ZnO material with a bimodal micro- and mesopore size distribution investigated as a desulfurizing sorbent presents a sorption capacity that reaches 87% of the theoretical value for desulfurization at 400 °C at breakthrough time. A deactivation model that considers the activity of the solid reactant was used to fit the experimental data. Good agreement between the experimental breakthrough curves and the model predictions are obtained. Manganese oxides are a type of metal oxide materials commonly used in catalytic applications. Little is known about the adsorption capabilities for the removal of sulfur compounds. One of these manganese oxides; amorphous manganese oxide (AMO) is highly promising material for low temperature sorption processes. Amorphous

Synthesis, characterization and reactivity of some lanthanide organometallics

International Nuclear Information System (INIS)

Marchal, N.

1991-12-01

Organo lanthanides with reactive metal-carbon bonds are obtained by direct synthesis of the metal (powder) and a hydrocarbon in ether medium, like with alkali metals. Two types of synthesis are envisaged: formation of covalent bonds by opening cycles, only biphenylene is reactive enough in regard to ytterbium and samarium, these organometallic compounds can also be prepared by the classical way, i.e. reaction of 2.2'-dilithio biphenyl on rare earth halogenides and coupling of 6.6-dimethylfulvene leading to dicyclopentadienyl compounds with Sm and Yb. The reactivity of these complexes is studied by catalysis of ethylene polymerization

Synthesis and photophysical characterizations of thermal-stable naphthalene benzimidazoles.

Science.gov (United States)

Erten-Ela, Sule; Ozcelik, Serdar; Eren, Esin

2011-07-01

Microwave-assisted synthesis, photophysical and electrochemical properties of thermal-stable naphthalene benzimidazoles and naphthalimides are studied in this paper. Microwave-assisted synthesis of naphthalene benzimidazoles provide higher yields than the conventional thermal synthesis. Comparative photophysical properties of naphthalene benzimidazoles and naphthalimides are revealed that conjugation of electron-donating group onto naphthalimide moiety increases fluorescence quantum yields. Fluorophore-solvent interactions are also investigated using Lippert-Mataga equation for naphthalimides and naphthalene benzimidazoles. Thermal stabilities of naphthalene benzimidazoles are better than naphthalimides due to increased aromaticity. The experimental E(LUMO) levels of naphthalene benzimidazoles are found to be between 3.15 and 3.28 eV. Therefore, naphthalene benzimidazole derivatives consisting of anchoring groups are promising materials in organic dye sensitized solar cells. © Springer Science+Business Media, LLC 2011

Synthesis, Characterization and Application of Nano Lepidocrocite ...

African Journals Online (AJOL)

NICO

Degradation of halogenated organic compounds using nanoparticles is one of the innovative ... way as the synthesis of nano zero-valent iron by using sodium .... +. −. 2и High. 2и Low. FWHM. Crystallite. /counts. /counts. /degree. /degree.

Synthesis and characterization of Ho3+ doped hafnium oxide TLD for radiation dosimeter

International Nuclear Information System (INIS)

Sekar, Nandakumar; Ganesan, Bharanidharan; Sahib, Hajee Reyaz Ali; Aruna, Prakasarao; Ganesan, Singaravelu; Thamilkumar, P.; Rai, R.R.

2017-01-01

Cancer is a dreaded disease which is treated by Radiotherapy, Chemotherapy and Surgery. Radiotherapy plays a vital role in treatment of cancer and recently measurements of invivo radiation dosimetric in patient is of great interest due to high dose gradients in advanced technology like IMRT, IGRT etc. Hence, for the last few decades, a great degree of interest has been shown for the hafnium oxide for radiation dosimetric applications, due to its high dielectric constant, wide band gap and better interface properties such as chemical stability, conduction band offset and thermodynamic stability. In the present study, Synthesis and characterization of Ho 3+ doped Hafnium oxide were carried out and its applications towards radiation dosimeter were investigated

CdTe and CdSe quantum dots: synthesis, characterizations and applications in agriculture

International Nuclear Information System (INIS)

Ung, Thi Dieu Thuy; Tran, Thi Kim Chi; Pham, Thu Nga; Nguyen, Quang Liem; Nguyen, Duc Nghia; Dinh, Duy Khang

2012-01-01

This paper highlights the results of the whole work including the synthesis of highly luminescent quantum dots (QDs), characterizations and testing applications of them in different kinds of sensors. Concretely, it presents: (i) the successful synthesis of colloidal CdTe and CdSe QDs, their core/shell structures with single- and/or double-shell made by CdS, ZnS or ZnSe/ZnS; (ii) morphology, structural and optical characterizations of the synthesized QDs; and (iii) testing examples of QDs as the fluorescence labels for agricultural-bio-medical objects (for tracing residual pesticide in agricultural products, residual clenbuterol in meat/milk and for detection of H5N1 avian influenza virus in breeding farms). Overall, the results show that the synthesized QDs have very good crystallinity, spherical shape and strongly emit at the desired wavelengths between ∼500 and 700 nm with the luminescence quantum yield (LQY) of 30–85%. These synthesized QDs were used in fabrication of the three testing fluorescence QD-based sensors for the detection of residual pesticides, clenbuterol and H5N1 avian influenza virus. The specific detection of parathion methyl (PM) pesticide at a content as low as 0.05 ppm has been realized with the biosensors made from CdTe/CdS and CdSe/ZnSe/ZnS QDs and the acetylcholinesterase (AChE) enzymes. Fluorescence resonance energy transfer (FRET)-based nanosensors using CdTe/CdS QDs conjugated with 2-amino-8-naphthol-6-sulfonic acid were fabricated that enable detection of diazotized clenbuterol at a content as low as 10 pg ml −1 . For detection of H5N1 avian influenza virus, fluorescence biosensors using CdTe/CdS QDs bound on the surface of chromatophores extracted and purified from bacteria Rhodospirillum rubrum were prepared and characterized. The specific detection of H5N1 avian influenza virus in the range of 3–50 ng μl −1 with a detection limit of 3 ng μL −1 has been performed based on the antibody-antigen recognition. (review)

Synthesis and characterization of carbon fibers obtained through plasma techniques

International Nuclear Information System (INIS)

Valdivia B, M.

2005-01-01

The study of carbon, particularly the nano technology is a recent field, the one which has important implications in the science of new materials. It investigation is of great interest for industries producers of ceramic, metallurgy, electronic, energy storage, biomedicine, among others. The diverse application fields are a reason at national as international level, so that many works are focused in the production of nano fibers of carbon. The Thermal plasma applications laboratory (LAPT) of the National Institute of Nuclear Research (ININ), it is carrying out works about carbon nano technology. The present work has as purpose to carry out the synthesis and characterization of the carbon nano fibers which are obtained by electric arch of alternating current (CA) to high frequencies and by a plasma gun of non transferred arch, where are used hydrocarbons like benzene, methane, acetylene like carbon source and ferrocene, nickel, yttrium and cerium oxide like catalysts. For both techniques its were thought about a relationship among hydrocarbon-catalyst that it favored to the nano fibers production. The obtained product of each experiment outlined it was analyzed by transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD), analysis with those were obtained pictures and diffraction graphs, which were observed to arrive to one conclusion on the operation conditions, same analysis with those were characterized the tests carried out according to the nano structures formation of carbon. (Author)

Synthesis and characterization of ceramics BNO (BiNbO4) added to 10% of CuO

International Nuclear Information System (INIS)

Sales, A.J.M.; Silva, P.M.O.; Rodrigues Junior, C.A.; Sombra, A.S.B.

2012-01-01

The study of the synthesis and structural characterization of ceramic BiNbO4 and behavior of density when added 10% by weight of CuO, with a view to applications in ceramic capacitors, are presented in this work. The BiNbO4 was prepared by conventional ceramic method. The milled powders were calcined for 2 hours at 850 °C for 3 hours and characterized by using a diffractometer Rigaku DMAXB of Co-α radiation. A more detailed characterization by XRD was performed using the program DBWS9807a using the Rietveld refinement of crystal structures, which confirmed the achievement of the α-BNO phase with orthorhombic structure. Were produced buks with the calcined powder, they were sintered at 925 °C. In order to study the grain morphology and distribution of pores in the ceramic body, the surface of the sample by adding 10% of CuO was analyzed by Scanning Electron Microscopy which confirmed a better densification. (author)

Synthesis and characterization of BNO (BiNbO4) ceramics added to 3% of ZnO

International Nuclear Information System (INIS)

Sales, A.J.M.; Pires Junior, G.F.M.; Rodrigues, H.O.; Sousa, D.G.; Sales, J.C.; Sombra, A.S.B.

2012-01-01

This work describes the synthesis and study of the structural characterization of ceramic BiNbO4 and density behavior when added 3% by weight of ZnO with a view to use in capacitors. The manufacture of BiNbO4 was made by conventional ceramic method. The powders were milled for two hours, calcined at 850 ° C for 3 h and characterized by XRD with Diffractometer Rigaku DMAXB of Co-α radiation. A more detailed XRD characterization was performed with the program DBWS9807a using the Rietveld refinement of crystal structures, which confirmed the achievement of phase -α-BiNbO4. Were made 'buks' with the calcined powder and these were sintered at 1025 ° C. In order to study the grain morphology and distribution of pores in the ceramic body, the surface of the sample with addition of 3% by weight of ZnO was analyzed by Scanning Electron Microscopy which confirmed a better densification. (author)

Extreme conditions synthesis, processing and characterization of metal-nitrides and alloys of mechanical and optoelectronic importance

International Nuclear Information System (INIS)

Serghiou, G; McGaff, A J; Russell, N; Morniroli, J P; Frost, D J; Odling, N; Boehler, R; Troadec, D; Lathe, C

2010-01-01

High density nitrides and group IV alloys are of growing importance for both ceramic and optoelectronic applications. We present here new data and processes in our ongoing preparation of alkaline earth and transition metal nitrides as well as group IV alloys, here, up to 25 GPa and 2300 K. We employ large volume and laser-heated diamond anvil cell techniques for synthesis, processing tools including focused ion beam, and synchrotron X-ray diffraction, transmission electron microscopy and scanning electron microscopy for characterization.

Synthesis and characterization of catalysts for the selective transformation of biomass-derived materials

Science.gov (United States)

Ghampson, Isaac Tyrone

The experimental work in this thesis focuses on generating catalysts for two intermediate processes related to the thermal conversion of lignocellulosic biomass: the synthesis and characterization of mesoporous silica supported cobalt catalysts for the Fischer-Tropsch reaction, and an exploration of the reactivity of bulk and supported molybdenum-based nitride catalysts for the hydrodeoxygenation (HDO) of guaiacol, a lignin model compound. The first section of the work details the synthesis of a series of silica-supported cobalt Fischer-Tropsch catalysts with pore diameters ranging from 2-23 nm. Detailed X-ray diffraction measurements were used to determine the composition and particle diameters of the metal fraction, analyzed as a three-phase system containing Cofcc, Cohcp and CoO particles. Catalyst properties were determined at three stages in catalyst history: (1) after the initial calcination step to thermally decompose the catalyst precursor into Co3O4, (2) after the hydrogen reduction step to activate the catalyst to Co and (3) after the FT reaction. From the study, it was observed that larger pore diameters supported higher turnover frequency; smaller pore diameters yielded larger mole fraction of CoO; XRD on post-reduction and post-FTS catalyst samples indicated significant changes in dispersivity after reduction. In the next section, the catalytic behaviors of unsupported, activated carbon-, alumina-, and SBA-15 mesoporous silica-supported molybdenum nitride catalysts were evaluated for the hydrodeoxygenation of guaiacol (2-methoxy phenol) at 300°C and 5 MPa. The nitride catalysts were prepared by thermal decomposition of bulk and supported ammonium heptamolybdate to form MoO 3 followed by nitridation in either flowing ammonia or a nitrogen/hydrogen mixture. The catalytic properties were strongly affected by the nitriding and purging treatment as well as the physical and chemical properties of support. The overall reaction was influenced by the

Synthesis and characterization of functionalized methacrylates for coatings and biomedical applications

Science.gov (United States)

Shemper, Bianca Sadicoff

The research presented in this dissertation involves the design of polymers for biomaterials and for coatings applications. The development of non-wettable, hard UV-curing, or reactive coatings is discussed. The biomaterials section involves the syntheses of linear and star-like polymers of the functionalized monomer poly(propylene glycol) monomethacrylate (PPGM) via atom transfer radical polymerization (ATRP) (Chapter II). Its copolymerization with a perfluoroalkyl ethyl methacrylate monomer (1H,1H,2H,2H-heptadecafluorodecyl methacrylate) and the syntheses of linear and star-like amphiphilic copolymers containing the fluorinated monomer and poly(ethyleneglycol) methyl ether methacrylate (MPEGMA) are discussed in Chapter III. The four-arm amphiphilic block copolymer obtained showed unique associative properties leading to micellization in selective solvents. Chapter IV includes research involving the design of films with low surface energy by incorporating fluorine into the polymer. The synthesis, characterization and polymerization of a perfluoroalkylether-substituted methacrylic acid (C8F7) are discussed, and the properties of coatings obtained after its photopolymerization on different substrates are evaluated to confirm formation of low-surface energy polymeric coatings. Subsequently, hard coatings based on methyl (alpha-hydroxymethyl)acrylate (MHMA) were prepared via photopolymerization using UV-light. Firstly, mechanistic investigations into the photopolymerization behavior of (alpha-hydroxymethyl)acrylates (RHMA's) are reported (Chapter V). RHMA derivatives were photopolymerized with various multifunctional acrylates and methacrylates and the effect of crosslinker type and degree of functionality on photopolymerization rates and conversions was investigated. Then, in Chapter VI the synthesis of a series of new crosslinkers is described and their photopolymerization kinetics was investigated in bulk. The effect of these novel crosslinkers on the

Lanthanum and yttrium oxysulfides activated by europium: (Ln1-x Eux)2 O2 S - Synthesis and characterization

International Nuclear Information System (INIS)

Luiz, J.M.

1989-01-01

The synthesis of lanthanum and yttrium oxysulfides activated by europium were obtained by thermal decomposition of lanthanum and yttrium oxalates doped with europium, under an argon and sulphur atmosphere. The thermal decomposition of these compounds is studied by differential thermal analysis (DTA). The characterization of these oxysulfides were made by chemical analyses, infrared spectroscopy, X-ray diffraction, scanning electron microscopy and emission spectroscopy. (M.V.M.)

Synthesis, characterization, bioactivity and potential application of phenolic acid grafted chitosan: A review.

Science.gov (United States)

Liu, Jun; Pu, Huimin; Liu, Shuang; Kan, Juan; Jin, Changhai

2017-10-15

In recent years, increasing attention has been paid to the grafting of phenolic acid onto chitosan in order to enhance the bioactivity and widen the application of chitosan. Here, we present a comprehensive overview on the recent advances of phenolic acid grafted chitosan (phenolic acid-g-chitosan) in many aspects, including the synthetic method, structural characterization, biological activity, physicochemical property and potential application. In general, four kinds of techniques including carbodiimide based coupling, enzyme catalyzed grafting, free radical mediated grafting and electrochemical methods are frequently used for the synthesis of phenolic acid-g-chitosan. The structural characterization of phenolic acid-g-chitosan can be determined by several instrumental methods. The physicochemical properties of chitosan are greatly altered after grafting. As compared with chitosan, phenolic acid-g-chitosan exhibits enhanced antioxidant, antimicrobial, antitumor, anti-allergic, anti-inflammatory, anti-diabetic and acetylcholinesterase inhibitory activities. Notably, phenolic acid-g-chitosan shows potential applications in many fields as coating agent, packing material, encapsulation agent and bioadsorbent. Copyright © 2017 Elsevier Ltd. All rights reserved.

The synthesis and characterization of biotin-silver-dendrimer nanocomposites as novel bioselective labels

Energy Technology Data Exchange (ETDEWEB)

Maly, J; Lampova, H; Semeradtova, A; Stofik, M [Faculty of Science, University of J E Purkynje, 40096 Usti nad Labem (Czech Republic); Kovacik, L, E-mail: malyjalga@seznam.c [Institute of Cellular Biology and Pathology, First Faculty of Medicine, Charles University in Prague (Czech Republic)

2009-09-23

This paper presents a synthesis of a novel nanoparticle label with selective biorecognition properties based on a biotinylated silver-dendrimer nanocomposite (AgDNC). Two types of labels, a biotin-AgDNC (bio-AgDNC) and a biotinylated AgDNC with a poly(ethylene)glycol spacer (bio-PEG-AgDNC), were synthesized from a generation 7 (G7) hydroxyl-terminated ethylenediamine-core-type (2-carbon core) PAMAM dendrimer (DDM) by an N,N'-dicyclohexylcarbodiimide (DDC) biotin coupling and a NaBH{sub 4} silver reduction method. Synthesized conjugates were characterized by several analytical methods, such as UV-vis, FTIR, AFM, TEM, ELISA, HABA assay and SPR. The results show that stable biotinylated nanocomposites can be formed either with internalized silver nanoparticles (AgNPs) in a DMM polymer backbone ('type I') or as externally protected ('type E'), depending on the molar ratio of the silver/DMM conjugate and type of conjugate. Furthermore, the selective biorecognition function of the biotin is not affected by the AgNPs' synthesis step, which allows a potential application of silver nanocomposite conjugates as biospecific labels in various bioanalytical assays, or potentially as fluorescence cell biomarkers. An exploitation of the presented label in the development of electrochemical immunosensors is anticipated.

Large area synthesis, characterization, and anisotropic etching of two dimensional tungsten disulfide films

International Nuclear Information System (INIS)

Mutlu, Zafer; Ozkan, Mihrimah; Ozkan, Cengiz S.

2016-01-01

Emergent properties of tungsten disulfide at the quantum confinement limit hold promise for electronic and optoelectronic applications. Here we report on the large area synthesis of atomically thin tungsten disulfide films with strong photoluminescence properties via sulfurization of the pre-deposited tungsten films. Detailed characterization of the pre-deposited tungsten films and tungsten disulfide films are performed using microscopy and spectroscopy methods. By directly heating tungsten disulfide films in air, we have shown that the films tend to be etched into a series of triangular shaped pits with the same orientations, revealing the anisotropic etching behavior of tungsten disulfide edges. Moreover, the dimensions of the triangular pits increase with the number of layers, suggesting a thickness dependent behavior of etching in tungsten disulfide films. This method offers a promising new avenue for engineering the edge structures of tungsten disulfide films. - Highlights: • Large-scale synthesis of WS_2 films is achieved via sulfurization of W films. • Annealing of W films leads to a substantial improvement in the quality of WS_2 films. • WS_2 films show laser power dependent photoluminescence characteristics. • WS_2 films are etched with well-oriented triangular pits upon annealing in air. • Anisotropic oxidative etching is greatly affected by the thickness of WS_2 films.

Low Temperature Synthesis, Chemical and Electrochemical Characterization of LiNi(x)Co(1-x)O2 (0 less than x less than 1)

Science.gov (United States)

Nanjundaswamy, K. S.; Standlee, D.; Kelly, C. O.; Whiteley, R. V., Jr.

1997-01-01

A new method of synthesis for the solid solution cathode materials LiNi(x)Co(1-x)O2 (0 less than x less than 1) involving enhanced reactions at temperatures less than or equal to 700 deg. C, between metal oxy-hydroxide precursors MOOH (M = Ni, Co) and Li-salts (Li2CO3, LiOH, and LiNO3) has been investigated. The effects of synthesis conditions and sources of Li, on phase purity, microstructure, and theoretical electrochemical capacity (total M(3+) content) are characterized by powder X-ray diffraction analysis, scanning electron microscopy, chemical analysis and room temperature magnetic susceptibility. An attempt has been made to correlate the electrochemical properties with the synthesis conditions and microstructure.

Biogenic synthesis of silver nanoparticles from white rot fungi: Their characterization and antibacterial studies

Directory of Open Access Journals (Sweden)

Krishna Gudikandula

2017-01-01

Full Text Available The advanced research and development of silver nanoparticles (AgNPs is vast due to their incredible applications today. In this work, research was focused on the production, characterization and antibacterial studies of silver nanoparticles (AgNPs. We used an environmentally friendly extracellular biosynthetic method for the production of the AgNPs. The reducing agents used to produce the nanoparticles were from culture filtrate extracts made from two white rot fungi. Synthesis of colloidal AgNPs was monitored by UV-Visible spectroscopy. The UV-Visible spectrum showed a peak between 419 and 421 nm corresponding to the Plasmon absorbance of the AgNPs. The characterization of the AgNPs such as their size and shape was performed by Transmission Electron Microscopy (TEM techniques which indicated a size range of 15–25 nm. The anti-bacterial activity of AgNPs was investigated by using four Gram-negative and four Gram-positive bacteria. All the bacterial strains are showing good antibacterial activity.

An alternative gas sensor material: Synthesis and electrical characterization of SmCoO3

International Nuclear Information System (INIS)

Michel, Carlos Rafael; Delgado, Emilio; Santillan, Gloria; Martinez, Alma H.; Chavez-Chavez, Arturo

2007-01-01

Single-phase perovskite SmCoO 3 was prepared by a wet-chemical synthesis technique using metal-nitrates and citric acid; after its characterization by thermal analyses and X-ray diffraction, sintering at 900 deg. C in air, gave single phase and well crystallized powders. The powders were mixed with an organic solvent to prepare a slurry, which was deposited on alumina substrates as thick films, using the screen-printing technique. Electrical and gas sensing properties of sintered SmCoO 3 films were investigated in air, O 2 and CO 2 , the results show that sensitivity reached a maximum value at 420 deg. C, for both gases. Dynamic tests revealed a better behavior of SmCoO 3 in CO 2 than O 2 , due to a fast response and a larger electrical resistance change to this gas. X-ray diffraction made on powders after electrical characterization in gases, showed that perovskite-type structure was preserved

Recent Advances in Two-Dimensional Materials with Charge Density Waves: Synthesis, Characterization and Applications

Directory of Open Access Journals (Sweden)

Mongur Hossain

2017-10-01

Full Text Available Recently, two-dimensional (2D charge density wave (CDW materials have attracted extensive interest due to potential applications as high performance functional nanomaterials. As other 2D materials, 2D CDW materials are layered materials with strong in-plane bonding and weak out-of-plane interactions enabling exfoliation into layers of single unit cell thickness. Although bulk CDW materials have been studied for decades, recent developments in nanoscale characterization and device fabrication have opened up new opportunities allowing applications such as oscillators, electrodes in supercapacitors, energy storage and conversion, sensors and spinelectronic devices. In this review, we first outline the synthesis techniques of 2D CDW materials including mechanical exfoliation, liquid exfoliation, chemical vapor transport (CVT, chemical vapor deposition (CVD, molecular beam epitaxy (MBE and electrochemical exfoliation. Then, the characterization procedure of the 2D CDW materials such as temperature-dependent Raman spectroscopy, temperature-dependent resistivity, magnetic susceptibility and scanning tunneling microscopy (STM are reviewed. Finally, applications of 2D CDW materials are reviewed.

Synthesis and characterization of α-, β-, and γ-Ga2o3 prepared from aqueous solutions by controlled precipitation

Science.gov (United States)

Li, Liandi; Wei, Wei; Behrens, Malte

2012-07-01

α, β and γ-Ga2O3 have been successfully obtained in an easily scalable synthesis using aqueous solution of gallium nitrate and sodium carbonate as starting materials without any surfactant and additive. α and β-Ga2O3 were obtained by calcination at 350 and 700 °С, respectively, of α-GaOOH, prepared by controlled precipitation at constant pH 6 and T = 55 °С, with 24 h of aging. Aging was necessary to fully convert the initially preciptated gel into a well-crystalline and phase-pure material. γ-Ga2O3 was obtained after calcination at 500 °С of gallia gel, synthesized at constant pH 4 and T = 25 °С, without aging. These three polymorphs have a for gallia relatively high surface area: 55 m2/g (α-Ga2O3), 23 m2/g (β-Ga2O3) and 116 m2/g (γ-Ga2O3). The combination of X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), nitrogen physisorption and thermogravimetry (TG) was employed to characterize the samples and their formation.

Individualized Pixel Synthesis and Characterization of Combinatorial Materials Chips

Directory of Open Access Journals (Sweden)

Xiao-Dong Xiang

2015-06-01

Full Text Available Conventionally, an experimentally determined phase diagram requires studies of phase formation at a range of temperatures for each composition, which takes years of effort from multiple research groups. Combinatorial materials chip technology, featuring high-throughput synthesis and characterization, is able to determine the phase diagram of an entire composition spread of a binary or ternary system at a single temperature on one materials library, which, though significantly increasing efficiency, still requires many libraries processed at a series of temperatures in order to complete a phase diagram. In this paper, we propose a “one-chip method” to construct a complete phase diagram by individually synthesizing each pixel step by step with a progressive pulse of energy to heat at different temperatures while monitoring the phase evolution on the pixel in situ in real time. Repeating this process pixel by pixel throughout the whole chip allows the entire binary or ternary phase diagram to be mapped on one chip in a single experiment. The feasibility of this methodology is demonstrated in a study of a Ge-Sb-Te ternary alloy system, on which the amorphous-crystalline phase boundary is determined.

Intercalation of Molybdate Ions into Ni/Zn Layered Double Hydroxide Salts: Synthesis, Characterization, and Preliminary Catalytic Activity in Methyl Transesterification of Soybean Oil

OpenAIRE

Colombo, Kamila; Maruyama, Swami A.; Yamamoto, Carlos I.; Wypych, Fernando

2017-01-01

This study reports the synthesis and characterization of a Ni/Zn layered double hydroxide salt intercalated with acetate ions and the subsequent replacement of the acetate ions with molybdate ions via an ion exchange reaction, conducted at two different pH values. Regardless of the pH employed during the synthesis, the basal spacing in the Ni/Zn layered double hydroxide salt decreased from 13.08 Å to approximately 9.5 Å, which agreed with intercalation of hydrated molybdate anions. The non-ca...

Synthesis and characterization of natural red dye from Caesalpinia sappan linn

Energy Technology Data Exchange (ETDEWEB)

Mulyanto, Subur, E-mail: subur.mulyanto@poltekba.ac.id [Graduate Program of Mechanical Engineering, SebelasMaret University, Jl. Ir. Sutami 36 A, Surakarta (Indonesia); Department of Mechanical Engineering, State Polytechnic of Balikpapan, Jl. Soekarno-Hatta Km.8 Balikpapan (Indonesia); Suyitno,, E-mail: suyitno@uns.ac.id; Rachmanto, Rendy Adhi, E-mail: rendy.ar@gmail.com; Hidayat, Lullus Lambang Govinda, E-mail: lulus-l@yahoo.com; Hadi, Syamsul, E-mail: syamsulhadi@ft.uns.ac.id [Department of Mechanical Engineering, SebelasMaret University, Jl. Ir. Sutami 36 A, Surakarta (Indonesia); Wibowo, Atmanto Heru, E-mail: aheruwibowo@yahoo.com [Department of Chemistry, SebelasMaret University, Jl. Ir. Sutami 36 A, Surakarta (Indonesia)

2016-03-29

The study reports the synthesis and characterization of natural red dye. The dyes were extracted from woods of Caesalpiniasappanlinn at varied temperatures of 70, 80, 90, and 100°C for three hours. The dry wood chips and water at a ratio of 6:1 were immersed in the reactor of 150 liters. The absorbance spectra of the natural red dyes were measured by ultra-violet-visible spectroscopy. Meanwhile, Fourier transform infrared spectroscopy was used to investigate the functional groups of the natural red dyes. In addition, the basic production cost was calculated and the fastness property towards cotton fabrics was investigated according to the Indonesia national standard of 105-C06:2010, 105-B01:2010, and 0288-2008. The results showed that the functional groups found the extracted red dyes indicated the complex bond of brazilein with peak absorbance at a wavelength of 538-540 nm. The extraction temperature also changed the functional group of brazilein. From the color, the absorbance peak, the functional groups, and the main production cost, the best parameter to synthesize the natural red dyes from Caesalpiniasappanlinn was at a temperature of 80°C for two hours. Moreover, the natural red dyes has the fastness to wash resistance, light resistance, and scrub resistance by 4-5, 4, and 3-4, respectively. However, further studies for synthesis the natural red dyes by using a continuous reactor are required to identify the naturally complex compounds in brazilein for improving the fastness properties and for reducing the cost.

Synthesis and characterization of natural red dye from Caesalpinia sappan linn

International Nuclear Information System (INIS)

Mulyanto, Subur; Suyitno,; Rachmanto, Rendy Adhi; Hidayat, Lullus Lambang Govinda; Hadi, Syamsul; Wibowo, Atmanto Heru

2016-01-01

The study reports the synthesis and characterization of natural red dye. The dyes were extracted from woods of Caesalpiniasappanlinn at varied temperatures of 70, 80, 90, and 100°C for three hours. The dry wood chips and water at a ratio of 6:1 were immersed in the reactor of 150 liters. The absorbance spectra of the natural red dyes were measured by ultra-violet-visible spectroscopy. Meanwhile, Fourier transform infrared spectroscopy was used to investigate the functional groups of the natural red dyes. In addition, the basic production cost was calculated and the fastness property towards cotton fabrics was investigated according to the Indonesia national standard of 105-C06:2010, 105-B01:2010, and 0288-2008. The results showed that the functional groups found the extracted red dyes indicated the complex bond of brazilein with peak absorbance at a wavelength of 538-540 nm. The extraction temperature also changed the functional group of brazilein. From the color, the absorbance peak, the functional groups, and the main production cost, the best parameter to synthesize the natural red dyes from Caesalpiniasappanlinn was at a temperature of 80°C for two hours. Moreover, the natural red dyes has the fastness to wash resistance, light resistance, and scrub resistance by 4-5, 4, and 3-4, respectively. However, further studies for synthesis the natural red dyes by using a continuous reactor are required to identify the naturally complex compounds in brazilein for improving the fastness properties and for reducing the cost.

A Network of AOPs for reduced thyroid hormone synthesis derived from inhibition of Thyroperoxidase - A common Molecular Initiating Event Leading to Species-Specific Indices of Adversity.

Science.gov (United States)

This collection of 3 AOPs describe varying outcomes of adversity dependent upon species in response to inhibition of thyroperoxidase (TPO) during development. Chemical inhibition of TPO, the molecular-initiating event (MIE), results in decreased thyroid hormone (TH) synthesis, a...

Synthesis and characterization of saturated polyester and ...

Indian Academy of Sciences (India)

but which can actually be used for processes, which pro- duce interesting ... ing the synthesis of saturated polyester (from GPET waste). This has been done for the .... The solid product obtained from the glycolysis of PET was bis(hydroxy ethyl ...

The experience of initiating injection drug use and its social context: a qualitative systematic review and thematic synthesis.

Science.gov (United States)

Guise, Andy; Horyniak, Danielle; Melo, Jason; McNeil, Ryan; Werb, Dan

2017-12-01

Understanding the experience of initiating injection drug use and its social contexts is crucial to inform efforts to prevent transitions into this mode of drug consumption and support harm reduction. We reviewed and synthesized existing qualitative scientific literature systematically to identify the socio-structural contexts for, and experiences of, the initiation of injection drug use. We searched six databases (Medline, Embase, PsychINFO, CINAHL, IBSS and SSCI) systematically, along with a manual search, including key journals and subject experts. Peer-reviewed studies were included if they qualitatively explored experiences of or socio-structural contexts for injection drug use initiation. A thematic synthesis approach was used to identify descriptive and analytical themes throughout studies. From 1731 initial results, 41 studies reporting data from 1996 participants were included. We developed eight descriptive themes and two analytical (higher-order) themes. The first analytical theme focused on injecting initiation resulting from a social process enabled and constrained by socio-structural factors: social networks and individual interactions, socialization into drug-using identities and choices enabled and constrained by social context all combine to produce processes of injection initiation. The second analytical theme addressed pathways that explore varying meanings attached to injection initiation and how they link to social context: seeking pleasure, responses to increasing tolerance to drugs, securing belonging and identity and coping with pain and trauma. Qualitative research shows that injection drug use initiation has varying and distinct meanings for individuals involved and is a dynamic process shaped by social and structural factors. Interventions should therefore respond to the socio-structural influences on injecting drug use initiation by seeking to modify the contexts for initiation, rather than solely prioritizing the reduction of individual

Chemical synthesis, characterization and evaluation of antimicrobial properties of Cu and its oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Moshalagae Motlatle, Abesach, E-mail: AMotlatle@csir.co.za; Kesavan Pillai, Sreejarani, E-mail: skpillai@csir.co.za; Rudolf Scriba, Manfred, E-mail: MRscriba@csir.co.za; Sinha Ray, Suprakas, E-mail: Rsuprakas@csir.co.za [Council for Scientific and Industrial Research, DST/CSIR Nanotechnology Innovation Centre, National Centre for Nano-Structured Materials (South Africa)

2016-10-15

Cu nanoparticles were synthesized using low-temperature aqueous reduction method at pH 3, 5, 7, 9 and 11 in presence of ascorbic acid and polyvinylpyrrolidone. The nanoparticles were characterized using transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction techniques. Results demonstrated a strong dependence of synthesis pH on the size, shape, chemical composition and structure of Cu nanoparticles. While lower pH conditions of 3 and 5 produced Cu{sup 0}, higher pH levels (more than 7) led to the formation of Cu{sub 2}O/CuO nanoparticles. The reducing capacity of ascorbic acid, capping efficiency of PVP and the resulting particle sizes were strongly affected by solution pH. The results of in vitro disk diffusion tests showed excellent antimicrobial activity of Cu{sub 2}O/CuO nanoparticles against a mixture of bacterial strains (Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa), indicating that the size as well as oxidation state of Cu contributes to the antibacterial efficacy. The results indicate that varying synthesis pH is a strategy to tailor the composition, structure and properties of Cu nanoparticles.

Computer-assisted spectral design and synthesis

Science.gov (United States)

Vadakkumpadan, Fijoy; Wang, Qiqi; Sun, Yinlong

2005-01-01

In this paper, we propose a computer-assisted approach for spectral design and synthesis. This approach starts with some initial spectrum, modifies it interactively, evaluates the change, and decides the optimal spectrum. Given a requested change as function of wavelength, we model the change function using a Gaussian function. When there is the metameric constraint, from the Gaussian function of request change, we propose a method to generate the change function such that the result spectrum has the same color as the initial spectrum. We have tested the proposed method with different initial spectra and change functions, and implemented an interactive graphics environment for spectral design and synthesis. The proposed approach and graphics implementation for spectral design and synthesis can be helpful for a number of applications such as lighting of building interiors, textile coloration, and pigment development of automobile paints, and spectral computer graphics.

Synthesis and characterization of natural hydroxyapatite (recycled) composites with titania

International Nuclear Information System (INIS)

Mendes Filho, Antonio Alves; Gouveia, Vitor Jose Pinto; Pereira, Renato Alves; Araujo, Fernando Gabriel da Silva; Sousa, Camila Mateus de

2010-01-01

Natural hydroxyapatite biphasic ceramics (recycled) with titania (TiO_2-Hap) were studied in this work. For the formation of such ceramic the powders were mixed natural hydroxyapatite obtained from veal bone by the hydrothermal method with titania (TiO_2), forming the composites H9T1. The powders, manually homogenized, were conformed in pellet and sintered at temperatures between 1200 and 1400 deg C The ceramic bodies were characterized by XRD and SEM/EDS. The initial results were not satisfactory and require new studies. (author)

Synthesis, characterization and application of lipase-conjugated citric acid-coated magnetic nanoparticles for ester synthesis using waste frying oil.

Science.gov (United States)

Patel, Unisha; Chauhan, Kishor; Gupte, Shilpa

2018-04-01

In the present work, magnetic nanoparticles (MNPs) were prepared by chemical precipitation of trivalent and divalent iron ions which were functionalized using citric acid. The bacterial isolate Staphylococcus epidermidis KX781317 was isolated from oil-contaminated site. The isolate produced lipase, which was purified and immobilized on magnetic nanoparticles (MNPs) for ester synthesis from waste frying oil (WFO). The characterization of MNPs employed conventional TEM, XRD and FTIR techniques. TEM analysis of MNPs showed the particle size in the range of 20-50 nm. FTIR spectra revealed the binding of citric acid to Fe 3 O 4 and lipase on citric acid-coated MNPs. The citric acid-coated MNPs and lipase-conjugated citric acid-coated MNPs had similar XRD patterns which indicate MNPs could preserve their magnetic properties. The maximum immobilization efficiency 98.21% of lipase-containing citric acid-coated MNPs was observed at ratio 10:1 of Cit-MNPs:lipase. The pH and temperature optima for lipase conjugated with Cit-MNPs were 7 and 35 °C, respectively. Isobutanol was found to be an effective solvent for ester synthesis and 1:2 ratio of oil:alcohol observed significant for ester formation. The ester formation was determined using TLC and the % yield of ester conversion was calculated. The rate of ester formation is directly proportional to the enzyme load. Formed esters were identified as isobutyl laurate ester and isobutyl myristate ester through GC-MS analysis.

On nuclear DD synthesis at the initial stage of nanosecond vacuum discharge with deuterium-loaded Pd anode

Science.gov (United States)

Kurilenkov, Yu K.; Gus'kov, S. Yu; Karpukhin, V. T.; Oginov, A. V.; Samoylov, I. S.

2018-01-01

Earlier, there was demonstrated generation of DD neutrons in an interelectrode medium of a low-energy (˜ 1 J) nanosecond vacuum discharge with a hollow cathode and a deuterium-loaded Pd anode. There was revealed essential role of formation of a virtual cathode and a potential well corresponding thereto in the processes of collisional DD synthesis in the interelectrode space. In this work, we have obtained as a result of an experiment and discussed the neutron yield at the very initial stage of the discharge, when the beam of auto-electrons just starts to irradiate the non-ideal surface of the deuterium-loaded Pd anode.

Nanocrystalline hydroxyapatite doped with magnesium and zinc: Synthesis and characterization

Energy Technology Data Exchange (ETDEWEB)

Kalita, Samar J. [Department of Mechanical, Materials and Aerospace Engineering, University of Central Florida, Orlando, FL 32816-2450 (United States)]. E-mail: samar@mail.ucf.edu; Bhatt, Himesh A. [Department of Mechanical, Materials and Aerospace Engineering, University of Central Florida, Orlando, FL 32816-2450 (United States)

2007-05-16

During recent years, there have been efforts in developing nanocrystalline bioceramics, to enhance their mechanical and biological properties for use in tissue engineering applications. In this research, we made an attempt to synthesize nanocrystalline bioactive hydroxyapatite (Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2}, HAp) ceramic powder in the lower-end of nano-range (2-10 nm), using a simple low-temperature sol-gel technique and studied its densification behavior. We further studied the effects of metal ion dopants during synthesis on powder morphology, and the properties of the sintered structures. Calcium nitrate and triethyl phosphite were used as precursors for calcium and phosphorous, respectively, for sol-gel synthesis. Calculated quantities of magnesium oxide and zinc oxide were incorporated as dopants into amorphous dried powder, prior to calcination at 250-550 {sup o}C. The synthesized powders were analyzed for their phases using X-ray diffraction technique and characterized for powder morphology and particle size using transmission electron microscopy (TEM). TEM analysis showed that the average particle size of the synthesized powders were in the range of 2-10 nm. The synthesized nano-powders were uniaxially compacted and then sintered at 1250 {sup o}C and 1300 {sup o}C for 6 h, separately, in air. A maximum average sintered density of 3.29 g/cm{sup 3} was achieved in structures sintered at 1300 {sup o}C, developed from nano-powder doped with magnesium. Vickers hardness testing was performed to determine the hardness of the sintered structures. Uniaxial compression tests were performed to evaluate the mechanical properties. Bioactivity and biodegradation behavior of the sintered structures were assessed in simulated body fluid (SBF) and maintained in a dynamic state.

Synthesis and characterization of fluorescence-labelled silica core-shell and noble metal-decorated ceria nanoparticles

Directory of Open Access Journals (Sweden)

Rudolf Herrmann

2014-12-01

Full Text Available The present review article covers work done in the cluster NPBIOMEM in the DFG priority programme SPP 1313 and focuses on synthesis and characterization of fluorescent silica and ceria nanoparticles. Synthetic methods for labelling of silica and polyorganosiloxane/silica core–shell nanoparticles with perylenediimide derivatives are described, as well as the modification of the shell with thiol groups. Photometric methods for the determination of the number of thiol groups and an estimate for the number of fluorescent molecules per nanoparticles, including a scattering correction, have been developed. Ceria nanoparticles decorated with noble metals (Pt, Pd, Rh are models for the decomposition products of automobile catalytic converters which appear in the exhaust gases and finally interact with biological systems including humans. The control of the degree of agglomeration of small ceria nanoparticles is the basis for their synthesis. Almost monodisperse agglomerates (40 ± 4–260 ± 40 nm diameter can be prepared and decorated with noble metal nanoparticles (2–5 nm diameter. Fluorescence labelling with ATTO 647N gave the model particles which are now under biophysical investigation.

Recent progress in the direct synthesis of hierarchical zeolites: synthetic strategies and characterization methods

KAUST Repository

Liu, Zhaohui

2017-06-16

Hierarchically structured zeolites combine the merits of microporous zeolites and mesoporous materials to offer enhanced molecular diffusion and mass transfer without compromising the inherent catalytic activities and selectivity of zeolites. This short review gives an introduction to the synthesis strategies for hierarchically structured zeolites with emphasis on the latest progress in the route of ‘direct synthesis’ using various templates. Several characterization methods that allow us to evaluate the ‘quality’ of complex porous structures are also introduced. At the end of this review, an outlook is given to discuss some critical issues and challenges regarding the development of novel hierarchically structured zeolites as well as their applications.

Synthesis, characterization, and potential use of 2-dodecylcyclobutanone as a marker for irradiated chicken

International Nuclear Information System (INIS)

Boyd, D.R.; Crone, A.V.J.; Hamilton, J.T.G.; Hand, M.V.; Stevenson, M.H.; Stevenson, P.J.

1991-01-01

The synthesis and characterization of 2-dodecylcyclobutanone is described. Solvent extraction techniques for the isolation of this compound from irradiated minced chicken meat and its detection by selected ion monitoring are outlined. The compound was not detected in either raw or cooked nonirradiated minced chicken meat by the methods used, but its presence was confirmed in the irradiated samples. 2-Dodecylcyclobutanone was detectable for 20 days postirradiation. The dose (4.7 kGy) of irradiation applied was below the recommended upper limit for food (10 kGy), and this compound may have potential as a marker for irradiated chicken meat and for other foods containing lipid

Synthesis Characterization and Decomposition Studies of tris[N-N-dibenzyidithocarbaso)Indium (III) Chemical Spray Deposition of Polycrystalline CuInS2 on Copper Films

Science.gov (United States)

Hehemann, David G.; Lau, J. Eva; Harris, Jerry D.; Hoops, Michael D.; Duffy, Norman V.

2005-01-01

This paper presents the results of the synthesis characterization and decomposition studies of tris[N-N-dibenzyidithocarbaso)Indium (III) with chemical spray deposition of polycrystalline CuInS2 on Copper Films.

Biological synthesis and characterization of silver nanoparticles ...

Indian Academy of Sciences (India)

or less have engrossed great attention due to their unusual and captivating ... ical method of nanoparticles synthesis using microorgan- isms, enzyme and plant or plant .... mined using Student's t-test with two-way Anova was set at p ≤ 0.05. 3.

Synthesis, characterization and photochemistry of a new ...

Indian Academy of Sciences (India)

The synthesis, crystal structure, redox characteristics and photochemistry of a new heptamolyb- ... The ability of [Mo7O24]−6 to function as a pure “inor- .... Abbreviations used: bpp = 1,3-bis(4-pyridyl)propane; 2-amp = 2-aminopyridine; DMSO ...

Synthesis and characterization of europium aluminophosphate

International Nuclear Information System (INIS)

Araujo, A.S.; Diniz, J.C.; Silva, A.O.S.

1998-01-01

Full text: Aluminophosphate molecular sieves (ALPO) represents a class of materials formed by AlO 2+ and PO 2- tetrahedra linked together through b the oxygen atom. The incorporation of metal cations, specifically rare earths, in the ALPO matrix, gives rise to generation of new materials that can be used as acid catalysts in chemical processes. In this work, it was synthesized hydrothermally a molecular sieve type Eu-ALPO-11, starting from an hydrated alumina (pseudobohemite), phosphoric acid solution, europium chloride, water, and di-isopropylamine (DIPA) as organic template. The gel of synthesis presented the following composition: 1.0 DIPA: 0.05 Eu 2 O 3 :0.95 Al 2 O 3 : 1.0 P 2 O 5 : 80 H 2 O The hydrogel was autoclaved at 170 deg C for a period of 3 days. After that the obtained solid was filtered, washed, dried and calcined at 500 deg C to remove the template. The sample was characterized by several physico-chemical methods, such a atomic absorption, FT-IR spectroscopy, X-ray diffraction, thermal analysis, scanning electron microscopy. Its spectroscopic properties was investigated by europium luminescence. The physico-chemical characterization of the Eu-ALPO-11 showed very good crystallinity, with AEL structure, and orthorhombic symmetry. Also, the material presents excellent thermal stability, with no structural collapse until 950 deg C. Through the luminescence spectra in the visible region, it was observed that the emission of the Eu 3+ is strongly influenced by the increasing of the 5d0 7f0 transition (Electric Dipole), as compared to the 5d0 7f1 transition (Magnetic Dipole) between the levels of 4f configuration perturbed by the crystalline field. The ED/MD ratio to the as synthesized sample was ca. 2.1, against ca. 1.1 relative to the calcined sample. The FT-IR spectra presented well defined absorption bands relative to Al-O and P-O bonds, of the structural internal tetrahedra (IT) and external links (EL): 1250- 950 cm -1 , symmetric stretching due to

Synthesis and characterization of Ce doped MFI zeolite

International Nuclear Information System (INIS)

Kalita, Banani; Talukdar, Anup K.

2012-01-01

Highlights: ► Cerium was incorporated into the tetrahedral position of MFI zeolite structure. ► Unit cell volume increases with an increase of Ce content in the framework of MFI. ► A band at 310 nm in the UV–vis spectra indicates Ce incorporation in MFI structure. ► The mass loss (%) in the region 373–423 K decreases with increase of Ce in MFI. - Abstract: Ce doped MFI (mobil five) zeolites with different Si to (Ce + Al) and different Ce to Al ratios were synthesized by a hydrothermal synthesis method. All the samples were characterized by different techniques such as X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), UV–vis diffuse reflectance spectroscopy (DRS) and scanning electron microscopy (SEM). The results showed that almost pure MFI phase was obtained in all cases with incorporation of cerium metal into the framework. The increase in unit cell parameters observed with an increase in Ce content is indicative of incorporation of Ce into the framework structure of microporous material MFI. Corroboration of the framework incorporation of Ce into the MFI zeolite structure was also obtained from the UV–vis DRS spectra by the presence of an absorption band at 280 nm. TGA and SEM of the samples provide complementary evidence for Ce incorporation into the framework MFI structure.

Neutral, seven-coordinate dioxime complexes of technetium(III): Synthesis and characterization

International Nuclear Information System (INIS)

Linder, K.E.; Malley, M.F.; Gougoutas, J.Z.; Unger, S.E.; Nunn, A.D.

1990-01-01

The tin-capped complexes 99 Tc(oxime) 3 (μ-OH)SnCl 3 [oxime = dimethylglyoxime (DMG) or cyclohexanedione dioxime (CDO)] can be prepared by the reduction of NH 4 TcO 4 with 2 equiv of SnCl 2 in the presence of dioxime and HCl. These tin-capped complexes can be readily converted into a new class of uncapped Tc-dioxime compounds, TcCl(oxime) 3 , by treatment with HCl. This reaction is reversible. Both the tin-capped and uncapped tris(dioxime) complexes can be converted to the previously reported boron-capped Tc-dioxime complexes TcCl(oxime) 3 BR (R = alkyl, OH) by reaction with boronic acids or with boric acid at low pH. All of these complexes [Tc(oxime) 3 (μ-OH)SnCl 3 , TcCl(oxime) 3 , and TcCl(oxime) 3 BR] appear to be neutral, seven-coordinate compounds of technetium(III). They have been characterized by elemental analysis, 1 H NMR and UV/visible spectroscopy, conductivity, and fast atom bombardment mass spectrometry. The synthesis, characterization, and reactivity of these compounds is discussed. The x-ray crystal structure analysis of TcCl(DMG) 3 and an abbreviated structure report on TcCl(DMG) 3 MeB are described. Crystal data for TcCl(DMG) 3 are reported. 23 refs., 6 figs., 5 tabs

Synthesis and characterization of magnetic Co nanoparticles: A comparison study of three different capping surfactants

International Nuclear Information System (INIS)

Lu Yu; Lu Xianmao; Mayers, Brian T.; Herricks, Thurston; Xia Younan

2008-01-01

This paper compares the performance of three long-chain acids-oleic and elaidic (both olefinic) and stearic (aliphatic)-as a capping agent in the synthesis of magnetic Co nanoparticles. The particles were formed through thermal decomposition of dicobalt octacarbonyl in toluene in the presence of the long-chain acid, and characterized by TEM, high-resolution TEM, and SQUID measurements. Infrared spectra revealed that some of the added olefinic acid was transformed from cis- to trans-configuration (for oleic acid) or from trans- to cis- (for elaidic acid) to facilitate the formation of a densely packed monolayer on the surface of Co nanoparticles. As compared to aliphatic acids, olefinic acids are advantageous for dense packing on small particles with high surface curvatures due to a bent shape of the cis-isomer. The presence of an olefinic acid is able to control particle growth, stabilize the colloidal suspension, and prevent the final product from oxidation by air. Our results indicate that oleic acid, elaidic acid, and a mixture of oleic/stearic acids or elaidic/stearic acids have roughly the same performance in serving as a capping agent for the synthesis of Co nanoparticles with a spherical shape and narrow size distribution. - Graphical abstract: Magnetic Co nanoparticles were synthesized in the presence of different capping agents and the effect of their molecular structures on the morphology of Co nanoparticles was analyzed. The transformation between cis- and trans-isomers of olefinic acids was critical to the formation of a densely packed monolayer on the surface of small nanoparticles characterized by high curvatures

Synthesis and characterization of the Y-type barium hexaferrite (Ba_2CoZnFe_1_2O_2_2) obtained by ultrasonic interdispersion of chemical precitates

International Nuclear Information System (INIS)

Junior, E.S.G.; Santos, M.R.C.; Jardim, P.M.; Ogasawara, T.; Almeida, L.H.

2011-01-01

This work is to study the synthesis and characterization of the Y-type barium hexaferrite powder (Ba2CoZnFe12O22) by chemical precipitation of the precursor materials Fe(OH)3, Co(OH)2, Zn(OH)2 and Ba(OH)2 separately and ultrasonic inter-dispersion, followed by drying and calcining. The study shows that the phase formation of the Y-type barium hexaferrite begins to emerge already at a temperature of 900 ° C with further phases still present, characterized by X-ray diffraction, the grain growth of the final product of the synthesis as a function of calcination temperature is visible by SEM, the measured magnetic of the powder through the hysteresis curve confirms that the material is magnetically soft at room temperature. The synthesis method developed in this research is an option to achieve the results that would be obtained if the co-precipitation of the ferric hydroxides, of cobalt, zinc and barium were thermodynamically possible. (author)

Synthesis and characterization of polyaniline–Fe@C magnetic nanocomposite powder

Energy Technology Data Exchange (ETDEWEB)

Fleaca, C.T., E-mail: claudiufleaca@yahoo.com [National Institute for Lasers, Plasma and Radiation Physics (NILPRP), Atomistilor 409, R-077125 Magurele (Romania); “Politehnica” University of Bucharest, Faculty of Applied Sciences, Physics Department, Independentei 313, Bucharest (Romania); Dumitrache, F. [National Institute for Lasers, Plasma and Radiation Physics (NILPRP), Atomistilor 409, R-077125 Magurele (Romania); “Politehnica” University of Bucharest, Faculty of Applied Sciences, Physics Department, Independentei 313, Bucharest (Romania); Morjan, I.; Niculescu, A.-M.; Sandu, I. [National Institute for Lasers, Plasma and Radiation Physics (NILPRP), Atomistilor 409, R-077125 Magurele (Romania); Ilie, A. [National Institute for Lasers, Plasma and Radiation Physics (NILPRP), Atomistilor 409, R-077125 Magurele (Romania); University of Bucharest, Physics Faculty, Atomistilor 405, Magurele (Romania); Stamatin, I.; Iordache, A. [3NanoSAE Research Center, University of Bucharest, Atomistilor 405, Magurele (Romania); Vasile, E. [“Politehnica” University of Bucharest, Faculty of Applied Chemistry and Materials Science, Gh. Polizu. 1-7, Bucharest (Romania); Prodan, G. [“Ovidius” University, Nanotechnology and Alternative Energy Sources Institute, Mamaia 124, Constanta (Romania)

2016-06-30

Highlights: • Carbon-encapsulated Fe–Fe{sub x}C nanoparticles were synthesized by laser pyrolysis. • Fe–C@PANI was obtained by redox polymerization in aqueous acid suspension. • The composite show low coercivity and 6 emu/g saturation magnetization. • Electric and redox behavior of Fe–C@PANI is similar with those of pure PANI. - Abstract: We report the synthesis of novel magnetic nanocomposite based on polyaniline (PANI) matrix and Fe–C nanoparticles. These hydrophobic Fe–Fe{sub x}C@C nanoparticles (having diameters under 20 nm) were synthesized by laser pyrolysis from Fe(CO){sub 5} and C{sub 2}H{sub 4}/H{sub 2} and dispersed in water using sodium carboxymethylcellulose, followed by the PANI coating using ultrasonication-assisted oxidative polymerization of aniline hydrochloride. The structure of the resulted composite was characterized by Transmission Electron Microscopy, X-ray diffraction and also by Raman and Infrared spectroscopy. The composite powder shows ferromagnetic behavior with low coercivity and 6.4 emu/g saturation magnetization, having also electric and electrochemical behavior similar with pure PANI reference.

Synthesis, characterization, and cytotoxicity evaluation of high-magnetization multifunctional nanoclusters

Energy Technology Data Exchange (ETDEWEB)

Petran, Anca; Radu, Teodora; Nan, Alexandrina [National Institute for Research and Development of Isotopic and Molecular Technologies (Romania); Olteanu, Diana; Filip, Adriana, E-mail: adrianafilip33@yahoo.com; Clichici, Simona; Baldea, Ioana [Iuliu Hatieganu University of Medicine and Pharmacy, Department of Physiology (Romania); Suciu, Maria; Turcu, Rodica, E-mail: rodica.turcu@itim-cj.ro [National Institute for Research and Development of Isotopic and Molecular Technologies (Romania)

2017-01-15

The paper presents the synthesis, characterization, and in vitro cytotoxicity tests of Fe{sub 3}O{sub 4} magnetic nanoclusters coated with ethylenediaminetetraacetic acid disodium salt (EDTA). Electron microscopy analysis (SEM) evidences that magnetite nanoparticles are closely packed into the clusters stabilized with EDTA with well-defined near spherical shapes and sizes in the range 100–200 nm. From XRD measurements, we determined the mean size of the crystallites inside the magnetic cluster about 36 nm. The saturation magnetization determined for the magnetic clusters stabilized with EDTA has high value, about 81.7 emu/g at 300 K. X-ray photoelectron spectroscopy has been used to determine both the elemental and chemical structure of the magnetic cluster surface. In vitro studies have shown that the magnetic clusters at low doses did not induce toxicity on human umbilical vein endothelial cells or lesions of the cell membrane. In contrast, at high doses, the magnetic clusters increased the lipid peroxidation and reduced the leakage of a cytoplasmic enzyme, lactate dehydrogenase (LDH), in parallel with increasing the antioxidant defense.

Synthesis and Characterization of Silver Nanoparticles for an Undergraduate Laboratory

Science.gov (United States)

Orbaek, Alvin W.; McHale, Mary M.; Barron, Andrew R.

2015-01-01

The aim of this simple, quick, and safe laboratory exercise is to provide undergraduate students an introduction to nanotechnology using nanoparticle (NP) synthesis. Students are provided two procedures that allow for the synthesis of different yet controlled sizes of silver NPs. After preparing the NPs, the students perform UV-visible…

Synthesis and characterization of strontium molybdate doped with copper, cobalt and zinc for purposes photocatalytic

International Nuclear Information System (INIS)

Dutra, F.B.; Silva, M.M.S.; Moriyama, A.L.L.; Souza, C.P.

2016-01-01

The broad concerns of contemporary society with environmental problems requires legislation and more effective techniques for wastewater treatment. In recent years, ceramic materials that have properties such as high melting points and high stability have been receiving great emphasis in several studies in particular heterogeneous photocatalysis, rapid and efficient method for the complete mineralization of contaminants. In this context, the present work deals with the synthesis and characterization of molybdate Strontium (SrMoO4) doped with copper, cobalt and zinc for the purpose of photocatalytic studies. The compounds were synthesized by complexation method EDTA / Citrate basic medium. The powders were characterized by Thermogravimetric Analysis (TG), X-Ray Diffraction (XRD), Particle size distribution by laser diffraction, Spectroscopy in the UV-Visible region, Energy Dispersive Spectroscopy (EDS) and Scanning Electron Microscopy (SEM), showing promising results as the crystalline phase of development and potential uses for the purpose of heterogeneous photocatalysis. (author)

Allyl borates: a novel class of polyhomologation initiators

KAUST Repository

Wang, De; Hadjichristidis, Nikolaos

2016-01-01

Allyl borates, a new class of monofunctional polyhomologation initiators, are reported. These monofunctional initiators are less sensitive and more effective towards polymethylene-based architectures. As an example, the synthesis of α

Synthesis and characterization of [11C]PK11195 as a PET radiopharmaceutical

International Nuclear Information System (INIS)

Almeida, Fernanda A. F.; Silveira, Marina B.; Oliveira, Amanda P.; Nascimento, Leonardo T.C.; Silva, Juliana B.; Mamede, Marcelo

2017-01-01

The radiopharmaceutical [ 11 C]PK11195 has been used for Positron Emission Tomography (PET) imaging of neuroinflammatory diseases. PK11195 is a tracer that binds to the benzodiazepine peripheral receptor (PBR) currently known as membrane translocator protein (TSPO). [ 11 C]PK11195 is differentially accumulated in tissues which have high TSPO expression, typically microglia activation in brain tissue, which has normally low TSPO expression. The aim of this work was to synthesize and characterize [ 11 C]PK11195 at the Radiopharmaceutical Production Unit of CDTN to make it available for future studies and applications in major brain inflammatory diseases. The [ 11 C]PK11195 syntheses were performed using Tracerlab™ FXC PRO (GE) by [ 11 C]methylation of the precursor (R)-[N-desmethyl] PK11195. Optimizations of the reaction conditions for the synthesis of [ 11 C]PK11195 were: Anhydrous dimethylsulfoxide (DMSO) volume, mass of precursor, and potassium hydroxide (KOH), labelling reaction temperature and time. After comparison of the results obtained for each condition evaluated, the standard best reaction parameters were defined as: 1mg of the precursor dissolved in 300 μL of DMSO (anhydrous); 10-15mg of KOH; and labeling reaction temperature of 40°C during 2 minutes. The total synthesis time was 40 minutes and the mean non-decay-corrected radiochemical yield was 10.93 ± 3.44%. All quality control criteria were met according to previous specifications. (author)

Phosphorylation of protein synthesis initiation factor 2 (elF-2) in the yeast Saccharomyces cerevisiae

International Nuclear Information System (INIS)

Romero, D.P.

1986-01-01

Initiation Factor 2 (elF-2) in the yeast Saccharomyces cerevisiae is comprised of 3 subunits. The control of protein synthesis in mammalian cells have been shown to involve the phosphorylation of the small (alpha) subunit by a specific protein kinase. Phosphorylation results in an inhibition of protein synthesis. In order to determine whether or not an analogous system is operative in yeast, the phosphorylation state of the alpha subunit of elF-2 in Saccharomyces was determined during various growth and nongrowth conditions. Cells were radiolabelled with 32 P and 35 S, and the whole cell lysates were analyzed by two dimensional gel electrophoresis. These experiments revealed that the smallest subunit (alpha, M/sub r/ = 31,000) is a phosphoprotein in vivo under a variety of growth and nongrowth conditions. This is in direct contrast to the pattern exhibited in mammalian cells. The fact that the small subunit of elF-2 in yeast is phosphorylated under a variety of physiological conditions indicates that such a covalent modification is important for some aspects of elF-2 function. In order to investigate this problem further, a protein kinase that specifically labels the alpha subunit of elF-2 in vitro was isolated. The kinase is not autophosphorylating, utilizes ATP as a phosphate donor, phosphorylates an exogenous protein, casein, modifies serine residues in elF-2, is cyclic nucleotide-independent, and is strongly inhibited by heparin

Assessment of PVA/silver nanocomposite hydrogel patch as antimicrobial dressing scaffold: Synthesis, characterization and biological evaluation

International Nuclear Information System (INIS)

Bhowmick, Sirsendu; Koul, Veena

2016-01-01

A novel, elastic, non-adhesive and antimicrobial hydrogel PVA scaffold (loaded with AgNPs) synthesized using freeze-thaw method has been characterized in this study. The direct visualization of the as synthesized (one-pot green synthesis methodology) AgNPs using TEM shows particle size in the range of 7 ± 3 nm. The minimum inhibitory concentration (MIC) of AgNPs for Staphylococcus aureus and Escherichia coli was estimated to be 7.81 μg/mL, whereas for Pseudomonas aeruginosa (gram negative) it was around 3.90 μg/mL. The antimicrobial efficacy of AgNPs was further studied by protein leakage, ROS and LDH activity assay. The quantitative elemental analysis of silver was calculated before and after release in phosphate buffer (pH-7.4) by atomic absorption spectroscopy. The antimicrobial efficacy of the scaffold was retained even after 96 h of release of AgNPs which suggests that the scaffold can be used as a reservoir for AgNPs to maintain a moist and sterile environment for a long period of time. - Highlights: • Green synthesis of AgNPs and evaluation of its antimicrobial efficacy • Synthesis of PVA hydrogel by freeze thaw technique • Antimicrobial activity of AgNPs loaded PVA hydrogel by zone of inhibition • Release kinetics of AgNPs from hydrogel by atomic absorption spectroscopy

Green Synthesis and Characterization of Palladium Nanoparticles Using Origanum vulgare L. Extract and Their Catalytic Activity

Directory of Open Access Journals (Sweden)

Mohammed Rafi Shaik

2017-01-01

Full Text Available The synthesis of Palladium (Pd nanoparticles by green methods has attracted remarkable attention in recent years because of its superiority above chemical approaches, owing to its low cost and ecological compatibility. In this present work, we describe a facile and environmentally friendly synthesis of Pd nanoparticles (Pd NPs using an aqueous extract of aerial parts of Origanum vulgare L. (OV as a bioreductant. This plant is available in many parts of the world as well as in Saudi Arabia and is known to be a rich source of phenolic components, a feature we fruitfully utilized in the synthesis of Pd NPs, using various concentrations of plant extracts. Moreover, the OV extract phytomolecules are not only accountable for the reduction and progression of nanoparticles, but they also act as stabilizing agents, which was confirmed by several characterization methods. The as-synthesized Pd nanoparticles (Pd NPs were analyzed using ultraviolet-visible spectroscopy (UV-Vis, Fourier-transform infrared spectroscopy (FT-IR, X-ray diffraction (XRD, transmission electron microscopy (TEM, energy-dispersive X-ray spectroscopy (EDX, and thermal gravimetric analysis (TGA. Further, FT-IR study has proven that the OV not merely represents a bioreductant but also functionalizes the nanoparticles. Furthermore, the green synthesized metallic Pd NPs were successfully applied as catalysts for selective oxidation of alcohols.

Assessment of PVA/silver nanocomposite hydrogel patch as antimicrobial dressing scaffold: Synthesis, characterization and biological evaluation

Energy Technology Data Exchange (ETDEWEB)

Bhowmick, Sirsendu; Koul, Veena, E-mail: veenak@iitd.ac.in

2016-02-01

A novel, elastic, non-adhesive and antimicrobial hydrogel PVA scaffold (loaded with AgNPs) synthesized using freeze-thaw method has been characterized in this study. The direct visualization of the as synthesized (one-pot green synthesis methodology) AgNPs using TEM shows particle size in the range of 7 ± 3 nm. The minimum inhibitory concentration (MIC) of AgNPs for Staphylococcus aureus and Escherichia coli was estimated to be 7.81 μg/mL, whereas for Pseudomonas aeruginosa (gram negative) it was around 3.90 μg/mL. The antimicrobial efficacy of AgNPs was further studied by protein leakage, ROS and LDH activity assay. The quantitative elemental analysis of silver was calculated before and after release in phosphate buffer (pH-7.4) by atomic absorption spectroscopy. The antimicrobial efficacy of the scaffold was retained even after 96 h of release of AgNPs which suggests that the scaffold can be used as a reservoir for AgNPs to maintain a moist and sterile environment for a long period of time. - Highlights: • Green synthesis of AgNPs and evaluation of its antimicrobial efficacy • Synthesis of PVA hydrogel by freeze thaw technique • Antimicrobial activity of AgNPs loaded PVA hydrogel by zone of inhibition • Release kinetics of AgNPs from hydrogel by atomic absorption spectroscopy.

Synthesis, characterization and magnetic properties of highly monodispersed PtNi nanoparticles

International Nuclear Information System (INIS)

Du, Juan-Juan; Yang, Yi; Zhang, Rong-Hua; Zhou, Xin-Wen

2015-01-01

In this paper, we report the controlled-synthesis of PtNi nanoparticles through galvanic displacement reaction and chemical reduction. The size, composition and morphology of the products are characterized by transmission electron microscopy (TEM), powder X-ray diffraction (XRD), energy dispersed X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) analyses. The structure and composition of the PtNi nanoparticles can be controlled by adjusting the synthetic conditions. The possible formation mechanism is obtained from the academic analysis and experimental studies. The results of the magnetic measurement illustrate that the PtNi nanoparticles show a superparamagnetic behavior with a blocking temperature (T B ) about 8.0 K. - Highlights: • Highly monodispersed PtNi nanoparticles were synthesized by galvanic displacement reaction. • The formation of Pt nanocrystals was the foremost step because of its self-catalysis effect. • The PtNi nanoparticles show a superparamagnetic behavior with a T B about 8.0 K

Synthesis and characterization of functionalized CNTs using soya and milk protein

Science.gov (United States)

saxena, Sanjay; ranu, Rachana; Hait, Chandan; Priya, Shruti

2014-10-01

Nanotechnology is the study of the phenomenon and manipulation of matter at atomic and molecular scale to enhance their older property and generate several new properties. Carbon nanotubes (CNTs) are one of the most commonly mentioned building blocks of nanotechnology. CNTs are very prevalent in today's world of medical research and are being highly researched in the fields of efficient drug delivery and bio sensing methods for disease treatment and health monitoring. There are number of methods for synthesizing CNTs. This is a biological method for synthesis of CNTs in which protein is used as carbon source and amino acids present in protein form complex with metal salt. The CNTs synthesized are then characterized and functionalized using techniques such as transmission electron microscopy, Fourier transform infra-red, nuclear magnetic resonance, ultra-violet visible spectroscopy, X-ray diffraction, etc. The properties of the synthesized CNTs are studied with the help of techniques such as thermo-gravimetric analysis, differential thermal analysis, and vibrating sample magnetometer, etc.

Ultrasonic-assisted chemical reduction synthesis and structural characterization of copper nanoparticles

Science.gov (United States)

Anh-Nga, Nguyen T.; Tuan-Anh, Nguyen; Thanh-Quoc, Nguyen; Ha, Do Tuong

2018-04-01

Copper nanoparticles, due to their special properties, small dimensions and low-cost preparation, have many potential applications such as in optical, electronics, catalysis, sensors, antibacterial agents. In this study, copper nanoparticles were synthesized by chemical reduction method with different conditions in order to investigate the optimum conditions which gave the smallest (particle diameter) dimensions. The synthesis step used copper (II) acetate salt as precursor, ascorbic acid as reducing agent, glycerin and polyvinylpyrrolidone (PVP) as protector and stabilizer. The assistance of ultrasonic was were considered as the significant factor affecting the size of the synthesized particles. The results showed that the copper nanoparticles have been successfully synthesized with the diameter as small as 20-40 nm and the conditions of ultrasonic waves were 48 kHz of frequency, 20 minutes of treated time and 65-70 °C of temperature. The synthesized copper nanoparticles were characterized by optical absorption spectrum, scanning electron microscopy (SEM), and Fourier Transform Infrared Spectrometry.

Synthesis, Characterization, and Self-Assembly of a Tetrathiafulvalene (TTF–Triglycyl Derivative

Directory of Open Access Journals (Sweden)

Sónia Pérez-Rentero

2018-04-01

Full Text Available In this work, we describe the synthesis, characterization, and self-assembly properties of a new tetrathiafulvalene (TTF–triglycyl low-molecular-weight (LMW gelator. Supramolecular organogels were obtained in various solvents via a heating–cooling cycle. Critical gelation concentrations (CGC (range ≈ 5–50 g/L and thermal gel-to-sol transition temperatures (Tgel (range ≈ 36–51 °C were determined for each gel. Fourier transform infrared (FT-IR spectroscopy suggested that the gelator is also aggregated in its solid state via a similar hydrogen-bonding pattern. The fibrillar microstructure and viscoelastic properties of selected gels were demonstrated by means of field-emission electron microscopy (FE-SEM and rheological measurements. As expected, exposure of a model xerogel to I2 vapor caused the oxidation of the TTF unit as confirmed by UV-vis-NIR analysis. However, FT-IR spectroscopy showed that the oxidation was accompanied with concurrent alteration of the hydrogen-bonded network.

Synthesis and Characterization of Fluoro- and Chlorobimetallic Alkoxides as Precursors for Luminescent Metal Oxide Materials via Sol-Gel Technique

Institute of Scientific and Technical Information of China (English)

ATHAR, Taimur; SEOK, Sang II; KWON, Jeong Oh

2007-01-01

Heterobimetallic alkoxides are broadly recognized as versatile precursors for luminescence materials, and efforts are being made to develop novel routes by applying the concept of geometrical molecular design, for their synthesis and to design a single source precursor suited to photoluminescent materials. Novel and new series of bimetallic alkoxides has been prepared by metathesis route. They exhibit a lower sensitivity towards hydrolysis and so they are easier to handle as compared to other alkoxides. All the compounds were characterized by elemental analysis, FT-IR and multinuclear NMR spectroscopies. FT-IR revealed that the molecular structure of these metal spectroscopy provided useful information about chemical shifts for better understanding the likely structure based on interactions with their coordinate metals. The mass spectra show similar types of fragmentation pattern.SEM-EDS analyses showed consistency with the formulation. XRD patterns show an enhanced homogeneity at high temperature. TGA measurements show that thermal decomposition occured in steps that depended entirely on the chemical compositions and the synthesis routes. SEM observation reveals that the morphology and particle size strongly depend on synthesis routes for their precursors.

Synthesis and characterization of Ag-Ni bimetallic nanoparticles by laser-induced plasma

International Nuclear Information System (INIS)

Xiao Qingmei; Yao Zhi; Liu Jiahong; Hai Ran; Oderji, Hassan Yousefi; Ding Hongbin

2011-01-01

We present an approach in which laser ablation deposition is used to synthesize silver-nickel bimetallic nanoparticles. A variety of techniques, including scanning electron microscopy, energy disperse spectroscopy and X-ray photoelectron spectroscopy have been used to characterize the morphology, composition and construction of synthesized bimetallic nanoparticles, respectively. The formation mechanism of bimetallic nanoparticles has been discussed. The Raman spectra of silver-nickel bimetallic nanoparticles have been analyzed. Time-of-flight mass spectrometry has been applied to directly measure intermediate species. The results indicate that diatomic AgNi is the most abundant species and suggest that the AgNi is the most stable intermediate which may play an important role in the synthesis process. Emission spectra demonstrate that the electron temperature is in the range of 6000-10000 K during the ablation process and increases with the laser power density.

Synthesis and characterization of silver nanoparticle composite with poly(p-Br-phenylsilane).

Science.gov (United States)

Kim, Myoung-Hee; Lee, Jun; Mo, Soo-Yong; Woo, Hee-Gweon; Yang, Kap Seung; Kim, Bo-Hye; Lee, Byeong-Gweon; Sohn, Honglae

2012-05-01

The one-pot synthesis and characterization of silver nanoparticle-poly(p-Br-phenylsilane) composites have been carried out. The conversion of silver(+1) salt to stable silver(0) nanoparticles is promoted by poly(p-Br-phenylsilane), Br-PPS possessing both possible reactive Si-H bonds in the polymer backbone and C-Br bonds in the substituents. The composites were characterized using XRD, TEM, FE-SEM, and solid-state UV-vis analytical techniques. TEM and FE-SEM data show the formation of the composites where large number of silver nanoparticles (less than 30 nm of size) are well dispersed throughout the Br-PPS matrix. XRD patterns are consistent with that for fcc-typed silver. The elemental analysis for Br atom and the polymer solubility confirm that the cleavage of C-Br bond and the Si-Br dative bonding were not occurred appreciably at ambient temperature. Nonetheless, TGA data suggest that some sort of cross-linking was occurred at high temperature. The size and processability of such nanoparticles depend on the ratio of metal to Br-PPS. In the absence of Br-PPS, most of the silver particles undergo macroscopic aggregation, which indicates that the polysilane is necessary for stabilizing the silver nanoparticles.

Biological synthesis and characterization of intracellular gold ...

Indian Academy of Sciences (India)

In the present study, Aspergillus fumigatus was used for the intracellular synthesis of gold nanoparticles. Stable nanoparticles were produced when an aqueous solution of chloroauric acid (HAuCl4) was reduced by A. fumigatus biomass as the reducing agent. Production of nanoparticles was confirmed by the colour ...

Synthesis and characterization of CuGeO3 photocatalyst using Green Chemistry and its application for the degradation of direct black dye