Electroosmotically enhanced sludge dewatering-pilot-plant study

CSIR Research Space (South Africa)

Smollen, M

1994-01-01

Full Text Available role in determining the ease or difficulty of phase separation. It seems that the inefficiency of dewatering applied to gelatinous and fine-particle sludges can be overcome by mechanical dewatering enhanced by electroosmosis. A prototype pilot-plant...

Optimizing MFT dewatering by controlling polymer mixing

Energy Technology Data Exchange (ETDEWEB)

Demoz, A.; Munoz, V.; Mikula, R. [Natural Resources Canada, Devon, AB (Canada). CANMET Western Research Centre

2010-07-01

A method of controlling polymer mixing for the dewatering of mature fine tailings (MFT) was presented. The method was developed to accelerate water release from MFT and to recover more water for re-use. Dewatering rates are dependent upon hydrodynamic conditions as well as various physical mixing variables. The effect of mixing energy on the rate and amount of released water flocculated MFT was investigated using different impellers in order to determine the release water amount and capillary suction time. The mixing energy effect on the structure of the flocculated MFT was analyzed using rheology and stereo microscopy techniques. Batch mixing tests were conducted to determine dewatering characteristics. Flow was described using the Herschel-Bulkley model. Results of the study demonstrated a clear peak in the amount of water released with the mixing time. The effect was applicable to rim-ditch thin-lift, and dewatering by centrifugation. tabs., figs.

Dewatering behaviour of ultrafine hard coal particles

Energy Technology Data Exchange (ETDEWEB)

Fischer, D.; Alizadeh, A.; Simonis, W.

1986-03-01

With decreasing particle diameter distribution the dewatering behaviour of coal gets increasingly complicated. A correlation between final moisture and content of particles below 25..mu..m in the course of centrifuging can be verified. This behaviour of the particles below 25..mu..m can be explained by the great specific surface, on the one hand, and by the distribution of the surface charge density, on the other hand. The charge density depends on the type of coal, on the minerals content and their make-up, as well as on the characteristics of the surrounding medium. The surface charge can be measured indirectly. Varying electrophoretic mobilities of the particles are observed in dependence on the type of raw material. In the neutral pH-range, minerals have a negative surface charge, while coal has a positive one. By way of adding reagents it is possible to invert the negative charges with complicated dewatering characteristics into positive charges. A similar influence will be exerted by changing the pH-value. 6 references.

Pressurised electro-osmotic dewatering of activated and anaerobically digested sludges: electrical variables analysis.

Science.gov (United States)

Citeau, M; Olivier, J; Mahmoud, A; Vaxelaire, J; Larue, O; Vorobiev, E

2012-09-15

Pressurised electro-osmotic dewatering (PEOD) of two sewage sludges (activated and anaerobically digested) was studied under constant electric current (C.C.) and constant voltage (C.V.) with a laboratory chamber simulating closely an industrial filter. The influence of sludge characteristics, process parameters, and electrode/filter cloth position was investigated. The next parameters were tested: 40 and 80 A/m², 20, 30, and 50 V-for digested sludge dewatering; and 20, 40 and 80 A/m², 20, 30, and 50 V-for activated sludge dewatering. Effects of filter cloth electric resistance and initial cake thickness were also investigated. The application of PEOD provides a gain of 12 points of dry solids content for the digested sludge (47.0% w/w) and for the activated sludge (31.7% w/w). In PEOD processed at C.C. or at C.V., the dewatering flow rate was similar for the same electric field intensity. In C.C. mode, both the electric resistance of cake and voltage increase, causing a temperature rise by ohmic effect. In C.V. mode, a current intensity peak was observed in the earlier dewatering period. Applying at first a constant current and later on a constant voltage, permitted to have better control of ohmic heating effect. The dewatering rate was not significantly affected by the presence of filter cloth on electrodes, but the use of a thin filter cloth reduced remarkably the energy consumption compared to a thicker one: 69% of reduction energy input at 45% w/w of dry solids content. The reduction of the initial cake thickness is advantageous to increase the final dry solids content. Copyright © 2012 Elsevier Ltd. All rights reserved.

Modelling dewatering behaviour through an understanding of solids formation processes. Part II--solids separation considerations.

Science.gov (United States)

Dustan, A C; Cohen, B; Petrie, J G

2005-05-30

An understanding of the mechanisms which control solids formation can provide information on the characteristics of the solids which are formed. The nature of the solids formed in turn impacts on dewatering behaviour. The 'upstream' solids formation determines a set of suspension characteristics: solids concentration, particle size distribution, solution ionic strength and electrostatic surface potential. These characteristics together define the suspension's rheological properties. However, the complicated interdependence of these has precluded the prediction of suspension rheology from such a fundamental description of suspension characteristics. Recent shear yield stress models, applied in this study to compressive yield, significantly reduce the empiricism required for the description of compressive rheology. Suspension compressibility and permeability uniquely define the dewatering behaviour, described in terms of settling, filtration and mechanical expression. These modes of dewatering may be described in terms of the same fundamental suspension mechanics model. In this way, it is possible to link dynamically the processes of solids formation and dewatering of the resultant suspension. This, ultimately, opens the door to improved operability of these processes. In part I of this paper we introduced an integrated system model for solids formation and dewatering. This model was demonstrated for the upstream processes using experimental data. In this current paper models of colloidal interactions and dewatering are presented and compared to experimental results from batch filtration tests. A novel approach to predicting suspension compressibility and permeability using a single test configuration is presented and tested.

Fundamental study for improvement of dewatering of fine coal/refuse. Final report, August 1981-December 1984

Energy Technology Data Exchange (ETDEWEB)

Chiang, S.H.; Klinzing, G.E.; Morsi, B.I.; Tierney, J.W.; Binkley, T.; Chi, S.M.; Huang, S.; Qamar, I.; Venkatadri, R.

1984-12-01

Fine coal in slurry form must be dewatered to minimize handling and transportation problems and be reduced to a desirable level for subsequent preparation of coal/water mixtures as a substitute utility fuel. The current practice is inadequate for the dewatering of fine coal, particularly for coal particles with sizes smaller than 400 mesh. Therefore, it is most desirable to develop improved mechanical methods for reducing the moisture content of fine coal. In the light of this, a fundamental study of the dewatering of fine coal/refuse was initiated in June 1979 and continued through 1984. The overall objective of the study is to seek improved methods of dewatering through a better understanding of the filtration and post-filtration processes. As a first step, efforts have been focused on the mechanism of dewatering in terms of the basic properties of coal (and refuse) particles and the microstructures of filter cakes, and their relations to filtration rate and final moisture content. Pittsburgh seam-Bruceton Mine coal was used as a base coal. During the past year, filter cakes from coals with widely varying size ranges were micrographically characterized. The effects of a number of surface active agents and of entrapped air bubbles on the filter cake properties were also studied. Modules of the network model for calculating single phase and two phase permeabilities were formulated and tested. The report is divided into four parts: summary and deliverables; work forecast for 1984-1985; detailed description of technical progress; and appendices. 21 refs., 55 figs., 17 tabs.

DEVELOPMENT OF DEWATERING AIDS FOR MINERALS AND COAL FINES

Energy Technology Data Exchange (ETDEWEB)

Roe-Hoam Yoon; Ramazan Asmatulu; Ismail Yildirim; William Jansen; Jinmig Zhang; Brad Atkinson; Jeff Havens

2004-07-01

MCT has developed a suite of novel dewatering chemicals (or aids) that are designed to cause a decrease in the capillary pressures of the water trapped in a filter cake by (1) decreasing the surface tension of water, (2) increasing the contact angles of the particles to be dewatered, and (3) causing the particles to coagulate, all at the same time. The decrease in capillary pressure in turn causes an increase in the rate filtration, an increase in throughput, and a decrease in pressure drop requirement for filtration. The reagents are used frequently as blends of different chemicals in order to bring about the changes in all of the process variables noted above. The minerals and coal samples tested in the present work included copper sulfide, lead sulfide, zinc sulfide, kaolin clay, talc, and silica. The laboratory-scale test work included studies of reagent types, drying cycle times, cake thickness, slurry temperature, conditioning intensity and time, solid content, and reagent dosages. To better understand the mechanisms involved, fundamental studies were also conducted. These included the measurements of the contact angles of the particles to be dewatered (which are the measures of particle hydrophobicity) and the surface tensions of the filtrates produced from dewatering tests. The results of the laboratory-scale filtration experiments showed that the use of the novel dewatering aids can reduce the moistures of the filter cake by 30 to 50% over what can be achieved using no dewatering aids. In many cases, such high levels of moisture reductions are sufficient to obviate the needs for thermal drying, which is costly and energy intensive. Furthermore, the use of the novel dewatering aids cause a substantial increase in the kinetics of dewatering, which in turn results in increased throughput. As a result of these technological advantages, the novel dewatering aids have been licensed to Nalco, which is one of the largest mining chemicals companies of the world. At

Ultra scale-down device to predict dewatering levels of solids recovered in a continuous scroll decanter centrifuge.

Science.gov (United States)

Lopes, A G; Keshavarz-Moore, E

2013-01-01

During centrifugation operation, the major challenge in the recovery of extracellular proteins is the removal of the maximum liquid entrapped within the spaces between the settled solids-dewatering level. The ability of the scroll decanter centrifuge (SDC) to process continuously large amounts of feed material with high concentration of solids without the need for resuspension of feeds, and also to achieve relatively high dewatering, could be of great benefit for future use in the biopharmaceutical industry. However, for reliable prediction of dewatering in such a centrifuge, tests using the same kind of equipment at pilot-scale are required, which are time consuming and costly. To alleviate the need of pilot-scale trials, a novel USD device, with reduced amounts of feed (2 mL) and to be used in the laboratory, was developed to predict the dewatering levels of a SDC. To verify USD device, dewatering levels achieved were plotted against equivalent compression (Gtcomp ) and decanting (Gtdec ) times, obtained from scroll rates and feed flow rates operated at pilot-scale, respectively. The USD device was able to successfully match dewatering trends of the pilot-scale as a function of both Gtcomp and Gtdec , particularly for high cell density feeds, hence accounting for all key variables that influenced dewatering in a SDC. In addition, it accurately mimicked the maximum dewatering performance of the pilot-scale equipment. Therefore the USD device has the potential to be a useful tool at early stages of process development to gather performance data in the laboratory thus minimizing lengthy and costly runs with pilot-scale SDC. © 2013 American Institute of Chemical Engineers.

POC-scale testing of an advanced fine coal dewatering equipment/technique

Energy Technology Data Exchange (ETDEWEB)

Groppo, J.G.; Parekh, B.K. [Univ. of Kentucky, Lexington, KY (United States); Rawls, P. [Department of Energy, Pittsburgh, PA (United States)

1995-11-01

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 {mu}m) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This project is a step in the Department of Energy`s program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. As the contract title suggests, the main focus of the program is on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process. in fact, in a recent survey conducted by U.S. DOE and Battelle, dewatering of fine clean coal was identified as the number one priority for the coal industry. This project will attempt to demonstrate an efficient and economic fine clean coal slurry dewatering process.

Dewatering of ultrafine coal: Final report, August 1984-December 1986

Energy Technology Data Exchange (ETDEWEB)

Chiang, Shiao-Hung; Klinzing, G.E.; Morsi, B.I.; Tierney, J.W.; Badgujar, M.; Binkley, T.; Cheng, Yisun; Huang, Suxuan; Qamar, I.; Venkatadri, R.

1986-12-01

The surfactant, Aerosol-OT, was used to wash distilled water cakes. In previous studies, cakes were washed with Triton X-114. The dewatering performance and influence on cake structure of the two reagents are compared. Also, filter cakes were analyzed using an image analysis system and micrographic analysis of coal particles was initiated. In the area of theoretical modelling, the concept of bond-flow correlation greatly improved the network model predicting the experimental desaturation curves. Predicted results for treated cakes suggested that the effect of the presence of surface-active agents was adequately accounted for. The effects of the various operating conditions on the filtration/dewatering characteristics of the 10 ..mu..m coal particles were assessed and comparisons with the -32 mesh coal were made as to its trends in response to changes in the operating conditions. 20 refs., 75 figs., 17 tabs.

Maximizing the benefits of a dewatering system

International Nuclear Information System (INIS)

Matthews, P.; Iverson, T.S.

1999-01-01

The use of dewatering systems in the mining, industrial sludge and sewage waste treatment industries is discussed, also describing some of the problems that have been encountered while using drilling fluid dewatering technology. The technology is an acceptable drilling waste handling alternative but it has had problems associated with recycled fluid incompatibility, high chemical costs and system inefficiencies. This paper discussed the following five action areas that can maximize the benefits and help reduce costs of a dewatering project: (1) co-ordinate all services, (2) choose equipment that fits the drilling program, (3) match the chemical treatment with the drilling fluid types, (4) determine recycled fluid compatibility requirements, and (5) determine the disposal requirements before project start-up. 2 refs., 5 figs

Fundamental study for improvement of dewatering of fine coal/refuse. Annual report, August 1982-August 1983

Energy Technology Data Exchange (ETDEWEB)

Chiang, S.H.; Klinzing, G.E.; Morsi, B.J.; Tierney, J.W.; Adams, J.; Bhat, N.; Binkley, T.; Chi, S.M.; Kakwani, R.; Qamar, I.

1983-09-01

The overall objective of the study is to seek improved methods of dewatering through a better understanding of the filtration and post-filtration processes. As a first step, efforts have been focused on the mechanism of dewatering in terms of basic properties of coal (and refuse) particles and microstructures of filter cakes, and their relations to filtration rate and final moisture content. Pittsburgh seam-Bruceton Mine coal was used as a base coal with experiments also being conducted with Upper Freeport and Illinois No. 6 coals. During the past year, filter cakes from the above coals with widely varied size ranges were micrographically characterized. The effects of a number of surface active agents and of entrapped air bubbles on the filter cake properties were also studied. A module of the network model for calculating single phase permeabilities was completed and tested. The report is divided into four parts: summary and deliverables; work forecast for the 1983-84; detailed descriptions of technical progress for particle/filter cake characterization; theoretical modeling, and enhanced dewatering methods; and appendices. 11 references, 35 figures, 11 tables.

Waste water from dewatering of peat

International Nuclear Information System (INIS)

Ringqvist, L.; Bergner, K.; Olsson, Tommy; Bystroem, P.

1991-01-01

The influence of waste water from mechanical dewatering of peat was tested on two species of stream invertebrates. We compared the effects of waste water from peat without any chemical treatment, and waste water from peat where one of the following treatments of the peat had preceded dewatering; a: acidification combined with addition of the cationic polymer Zetag 78 FS40, b: addition of aluminium in combination with the anionic polymer Magnafloc E10, c: polymerisation of the peat by acidification and addition of ferrous chloride and hydrogen peroxide. Waste water from Al/Magnafloc and from the polymerisation treatments had a higher content of suspended matter and a higher oxygen demand than those of other treatments. Total metal content of the water from all treatments was higher than in water from non-treated peat. Survival and growth of nymphs of the mayfly Heptagenia fuscogrisa and the stonefly Nemoura cinerea were compared in waste water from the different treatments. In all tests, the waste water was diluted to 5% (volume) with unchlorinated tapwater and pH was between 7.0-8.0 in all treatments during the experiment. The nymphs were fed with birch leaves that had been incubated in natural stream water for one month. Under these conditions, we did not find any significant effect of waste water on either survival or growth of these two species

The utilization of forward osmosis for coal tailings dewatering

Science.gov (United States)

The feasibility of dewatering coal tailings slurry by forward osmosis (FO) membrane process was investigated in this research. A prototype cell was designed and used for the dewatering tests. A cellulosic FO membrane (Hydration Technology Innovations, LLC, Albany, OR) was used fo...

Techno-economic evaluation of microalgae harvesting and dewatering systems

NARCIS (Netherlands)

Fasaei, F.; Bitter, J.H.; Slegers, P.M.; Boxtel, van A.J.B.

2018-01-01

Microalgal biomass is processed into products by two main process steps: 1) harvesting and dewatering; and 2) extraction, fractionation and conversion. The performance of unit operations for harvesting and dewatering is often expressed in qualitative terms, like “high energy consumption” and “low in

Dewatering blastholes cuts explosives costs

Energy Technology Data Exchange (ETDEWEB)

Pilshaw, S.R.

1987-11-01

Large mining operations often require a combination of presplitting and dewatering with blasthole pumps. Increasing the percentage of bulk ANFO in any blast will reduce cost and should increase profitability.

[Magnetic Fe₃O₄Microparticles Conditioning-Pressure Electro-osmotic Dewatering (MPEOD) of Sewage Sludge].

Science.gov (United States)

Qian, Xu; Wang, Yi-li; Zhao, Li

2016-05-15

For magnetic Fe₃O₄ microparticles conditioning--pressure electro-osmotic dewatering (MPEOD) process of activated sludge (AS), the effects of operating parameters (optimal dosage of Fe₃O₄, electric field duration, mechanical pressure and voltage) on the dewatering efficiency and energy consumption were investigated, and the optimal conditions were determined. Moreover, the properties of supernatant and sludge along MPEOD process were studied as well as the interaction force between the sludge biosolids. Taking the energy consumption into consideration, the results showed that the optimal dewatering effect for AS could be achieved with a magnetic Fe₃O₄ microparticles dosage of 0.15 g · g⁻¹, an electric field duration of 2 h, a mechanical pressure of 400-600 kPa and a voltage of 30-50 V. When MPEOD was conducted at 400 kPa and 50 V for 2 h, the sludge reduction rate reached 98.30%, the percentage of water removal was 99.34% and the moisture content of AS decreased from 99.18% to 44.46%. The corresponding consumption of energy was 0.013 3 kW · h · kg⁻¹. The coagulation mechanism played a slight role in the AS conditioning with magnetic Fe₃O₄ micro-particles. In fact, magnetic Fe₃O₄micro-particles could greatly decrease the acid-base interaction (WA) between AS biosolids, cause floc growth and enlarge pores in AS aggregates, which will be beneficial to AS dewatering. Compared to DLVO theory, the extended DLVO theory could accurately describe the aggregation and dispersion behavior of sludge particles.

Dewatering and Treatment of Septage Using Vertical Flow Constructed Wetlands

Directory of Open Access Journals (Sweden)

Yee Yong Tan

2017-10-01

Full Text Available The vertical flow constructed wetland (VFCW has become an attractive decentralised technology for septage treatment. One of the main purposes of the septage treatment is to reduce the volume of raw septage through dewatering, where the solids content is retained in the wetland bed and the water content is released. The retention of solids forms a layer of sludge deposit at the wetland surface, and the drained water, the so-called leachate, typically contains a lower solids content. This article reports the performance of dewatering and filtration of a pilot-scale VFCW designed for septage treatment. A comparison between two feeding strategies, hydraulic loading rate (HLR and solids loading rate (SLR, is presented. The dewatering efficiency through drainage was found to be dependent on the solids load. The removal of total solids (TS and chemical oxygen demand (COD were excellent as the quality of leachate showed that more than 90% of TS and COD were retained in the system. This study reveals that the feeding based on SLR delivered a more sustainable performance for dewatering and solids removal. The build-up of sludge deposit significantly deteriorated the dewatering efficiency through drainage, but it tended to improve the filtration capacity.

Microalgae dewatering based on forward osmosis employing proton exchange membrane.

Science.gov (United States)

Son, Jieun; Sung, Mina; Ryu, Hoyoung; Oh, You-Kwan; Han, Jong-In

2017-11-01

In this study, electrically-facilitated forward osmosis (FO) employing proton exchange membrane (PEM) was established for the purpose of microalgae dewatering. An increase in water flux was observed when an external voltage was applied to the FO equipped with the PEM; as expected, the trend became more dramatic with both concentration of draw solution and applied voltage raised. With this FO used for microalgae dewatering, 247% of increase in flux and 86% in final biomass concentration were observed. In addition to the effect on flux improvement, the electrically-facilitated FO exhibited the ability to remove chlorophyll from the dewatered biomass, down to 0.021±0015mg/g cell. All these suggest that the newly suggested electrically-facilitated FO, one particularly employed PEM, can indeed offer a workable way of dewatering of microalgae; it appeared to be so because it can also remove the ever-problematic chlorophyll from extracted lipids in a simultaneous fashion. Copyright © 2017 Elsevier Ltd. All rights reserved.

Macroinvertebrate community responses to a dewatering disturbance gradient in a restored stream

Directory of Open Access Journals (Sweden)

J. D. Muehlbauer

2011-06-01

Full Text Available Dewatering disturbances are common in aquatic systems and represent a relatively untapped field of disturbance ecology, yet studying dewatering events along gradients in non-dichotomous (i.e. wet/dry terms is often difficult. Because many stream restorations can essentially be perceived as planned hydrologic manipulations, such systems can make ideal test-cases for understanding processes of hydrological disturbance. In this study we used an experimental drawdown in a 440 ha stream/wetland restoration site to assess aquatic macroinvertebrate community responses to dewatering and subsequent rewetting. The geomorphic nature of the site and the design of the restoration allowed dewatering to occur predictably along a gradient and decoupled the hydrologic response from any geomorphic (i.e. habitat heterogeneity effects. In the absence of such heterogeneous habitat refugia, reach-scale wetted perimeter and depth conditions exerted a strong control on community structure. The community exhibited an incremental response to dewatering severity over the course of this disturbance, which was made manifest not as a change in community means but as an increase in community variability, or dispersion, at each site. The dewatering also affected inter-species abundance and distributional patterns, as dewatering and rewetting promoted alternate species groups with divergent habitat tolerances. Finally, our results indicate that rapid rewetting – analogous to a hurricane breaking a summer drought – may represent a recovery process rather than an additional disturbance and that such processes, even in newly restored systems, may be rapid.

Microbiological and physico-chemical studies on irradiated dewatered sludge

International Nuclear Information System (INIS)

Hilmy, N.; Suwirma, S.; Harsoyo; Suhadi, F.

1987-01-01

Microbiological and physico-chemical studies on irradiated dewatered sludge. Microbiological and physico-chemical dewatered have been carried out and non-irradiated dewatered sludge of Jakarta city, collected during the rainy and dry season. Total bacterial counts of non-irradiated dewatered sludge with water content of around 20%, were found to be about 7x10 8 per g during the rainy season and 7x10 6 up to 1.3x10 8 per g during the dry season, while coliform fecal Streptococcus and Pseudomonas were found to be 1.6x10 4 to 1.0x10 7 , 3x10 5 , and 5x10 3 per g, respectively. No Salmonella, Shigella and Vibrio were detected in all of the samples observed. About 10% of the total number of coliforms were found to be Escherichia coli. A dose of 6 kGy could eliminate the coliform, E. Coli, fecal Streptococcus and Pseudomonas from all of the dewatered sludge observed. The nutrient value of the sludge was sufficient, i.e. total nitrogen content ranged between 1 and 4,42%, phosphorus between 1.55 and 2.36%, and potassium between 0,1 and 0,2% of dry matter. Heavy metal contents were found a little bit high to be applied as animal feed, but it is still acceptable for soil conditioner. Combining 3 months storage at ambient environment and irradiation dose of 2.5 kGy were found to work synergistically to eliminate coliforms and E. Coli from sludge. (author). 8 figs, 17 refs

Electrical field: a historical review of its application and contributions in wastewater sludge dewatering.

Science.gov (United States)

Mahmoud, Akrama; Olivier, Jérémy; Vaxelaire, Jean; Hoadley, Andrew F A

2010-04-01

Electric field-assisted dewatering, also called electro-dewatering, is a technology in which a conventional dewatering mechanism such a pressure dewatering is combined with electrokinetic effects to realize an improved liquid/solids separation, to increase the final dry solids content and to accelerate the dewatering process with low energy consumption compared to thermal drying. Electro-dewatering is not a new idea, but the practical industrial applications have been limited to niche areas in soil mechanics, civil engineering, and the ceramics industry. Recently, it has received great attention, specially, in the fields of fine-particle sludge, gelatinous sludge, sewage sludge, pharmaceutical industries, food waste and bull kelp, which could not be successfully dewatered with conventional mechanical methods. This review focuses on the scientific and practical aspects of the application of an electrical field in laboratory/industrial dewatering, and discusses this in relation to conventional dewatering techniques. A comprehensive bibliography of research in the electro-dewatering of wastewater sludges is included. As the fine-particle suspensions possess a surface charge, usually negative, they are surrounded by a layer with a higher density of positive charges, the electric double layer. When an electric field is applied, the usually negative charged particles move towards the electrode of the opposite charge. The water, commonly with cations, is driven towards the negative electrode. Electro-dewatering thus involves the well-known phenomena of electrophoresis, electro-osmosis, and electromigration. Following a detailed outline of the role of the electric double layer and electrokinetic phenomena, an analysis of the components of applied voltage and their significance is presented from an electrochemical viewpoint. The aim of this elementary analysis is to provide a fundamental understanding of the different process variables and configurations in order to

Ground movement and deformation due to dewatering and open pit excavation

International Nuclear Information System (INIS)

Liu, B.; Yang, J.; Zhang, J.

1996-01-01

In the application of stochastic medium theory, it is assumed that ground movement process has the property of Markov Process. Based on superposition principle and rock consolidation principle, the ground movement and deformation due to dewatering and open pit excavation can be calculated. The comparison between the field measurements in Morwell Open Pit, Latrobe Valley (Victoria, Australia) and the calculated results shows the validity of the method in this paper. 5 refs

Determination of Juice Removal Difficulty from Mash Cake in Cassava Mash Dewatering Operation

Directory of Open Access Journals (Sweden)

Oladele Peter KOLAWOLE

2012-08-01

Full Text Available Cassava processing equipment operators have limited knowledge; this militates against the success recorded in the research so far in cassava mash dewatering. New dewatering schemes to make food processing economical to handle are in progress. Common dewatering processes use a variety of mechanical means such as screw presses and belt presses. Experiments were conducted using three samples of TMS 4(2 1425 variety while evaluating the difficulty of separating juice from mash cake. Average specific cake resistance (a of 5×1011 m/kg was obtained confirming that it is moderately easy to dewatering.

Enhanced Brine Dewatering System, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide an easily scalable means of completely recovering usable water from byproducts created by...

Enhanced Brine Dewatering System, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide a scalable means of completely recovering usable water from byproducts created by reverse...

Effects of gamma-radiation at pilot plant level as compared to effects of pasteurization on the dewatering of sewage sludges

International Nuclear Information System (INIS)

Groneman, A.F.

1975-01-01

Dewatering and disposal of sludge are costly and time consuming processes. At a pilot plant near Munich efforts were made to estimate the effects of ionizing radiation on dewatering characteristics of different sludges, used for recycling in agriculture. The ease with which sludge drains on drying beds and in mechanical devices is reflected in the value of the specific resistance to filtration. A dose of 300 krad, delivered at an average dose rate of 62 krad per hour in the irradiation plant, was effective for disinfection and reduced the specific resistance to filtration in sludges from the waste water works at Geiselbullach and Starnberg from 24.2 x 10 9 sec 2 /g and 18.0 x 10 9 sec 2 /g to 9.7 x 10 9 sec 2 /g and 5.6 x 10 9 sec 2 /g, respectively. These improved dewatering properties were associated with a clear increase of the compressibility of the anaerobically digested sludges. Pasteurization at 70 0 C during 30 minutes drastically deteriorated the dewatering properties, raising the specific resistance to values approximately 4 times as high as the specific resistance in irradiated sludges. Information obtained from filterability tests was confirmed by plant operators who noticed that irradiated sludges dewatered much better than untreated sludges in drying beds. Experimental evidence indicated that the conditioning effect of gamma irradiation persisted for more than 20 days suggesting that permanent changes were induced in the physical-chemical properties of the domestic, anaerobically digested sludges. Measurements of electrophoretic mobilities showed that the negative electrostatic charges of colloidal particles in sludges were reduced by gamma irradiation whereas pasteurization increased this negative electrostatic charge. Evidence indicated that the specific resistance was considerably increased by effects of the recirculating pumping. This pumping is done to obtain a homogeneous irradiation dose for disinfection. Alternative designs for irradiation

Electric dewatering and drying of fine-grained products; Elektrisk afvanding og toerring af finkornede produkter

Energy Technology Data Exchange (ETDEWEB)

Hansen, H.K.; Villumsen, A.

2001-07-01

The aim of the project was to elucidate four aspects related to using electric direct current to find an energy saving alternative to existing methods within dewatering of fine-grained products. The four aspects were a) electrophoresis forced sedimentation of chalk slurry, b) electro osmotic dewatering of chalk slurry, c) electro osmotic dewatering of agricultural chalk and d) electro osmotic dewatering of liquid organic wastes. (EHS)

Flotation: A promising microalgae harvesting and dewatering technology for biofuels production.

Science.gov (United States)

Ndikubwimana, Theoneste; Chang, Jingyu; Xiao, Zongyuan; Shao, Wenyao; Zeng, Xianhai; Ng, I-Son; Lu, Yinghua

2016-03-01

Microalgal biomass as renewable energy source is believed to be of great potential for reliable and sustainable biofuels production. However, microalgal biomass production is pinned by harvesting and dewatering stage thus hindering the developing and growing microalgae biotechnology industries. Flotation technology applied in mineral industry could be potentially applied in microalgae harvesting and dewatering, however substantial knowledge on different flotation units is essential. This paper presents an overview on different flotation units as promising cost-effective technologies for microalgae harvesting thus bestowing for further research in development and commercialization of microalgae based biofuels. Dispersed air flotation was found to be less energy consuming. Moreover, Jameson cell flotation and dispersed ozone flotation are believed to be energy efficient microalgae flotation approaches. Microalgae harvesting and dewatering by flotation is still at embryonic stage, therefore extended studies with the focus on life cycle assessment, sustainability of the flotation unit, optimization of the operating parameters using different algal species is imperative. Though there are a number of challenges in microalgae harvesting and dewatering, with well designed and developed cultivation, harvesting/dewatering, extraction and conversion technologies, progressively, microalgae technology will be of great potential for biological carbon sequestration, biofuels and biochemicals production. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mechanical dewatering of silage; Mechanische Entwaesserung von Silage

Energy Technology Data Exchange (ETDEWEB)

Scholz, Volkhard; Daries, Werner [Leibniz-Institut fuer Agrartechnik Potsdam-Bornim e.V. (ATB), Potsdam (Germany). Abteilung Technik der Aufbereitung, Lagerung und Konservierung; Rinder, Ralf [Anhydro GmbH, Kassel (Germany)

2009-07-01

The use of screw presses for dewatering of silage is energetically more efficient than thermal drying. Tests with two types of screw presses show that on dry matter flow rates of more than 1.0 tDM/h the specific energy consumption is less than 30 kWh/tDM. The water content of the silage is decreased by 5 to 20 % and the share of undesired ingredients by 2 to 30 %. Besides press design and plant species, in particular moisture content, chip size and density of silage are essentially for the dewatering success. (orig.)

Pervaporation applied for dewatering of reaction mixture during esterification

OpenAIRE

Krasiński Andrzej; Wierzba Patrycja; Grudzień Agata; Hajmowicz Halina; Zawada Krzysztof; Synoradzki Ludwik

2016-01-01

In this work the esterification of diethyl tartrate was studied. The research was focused on the enhancement of reversible reaction yield, which is accomplished by dewatering of the reaction mixture. The removal of water shifts the equilibrium towards the main product. Pervaporation was applied for this purpose, and results were compared to distillation. The advantages and limitations of both processes are discussed. The experimental part consists of dewatering of mixture after the reaction h...

Demonstration of FBRM as process analytical technology tool for dewatering processes via CST correlation.

Science.gov (United States)

Cobbledick, Jeffrey; Nguyen, Alexander; Latulippe, David R

2014-07-01

The current challenges associated with the design and operation of net-energy positive wastewater treatment plants demand sophisticated approaches for the monitoring of polymer-induced flocculation. In anaerobic digestion (AD) processes, the dewaterability of the sludge is typically assessed from off-line lab-bench tests - the capillary suction time (CST) test is one of the most common. Focused beam reflectance measurement (FBRM) is a promising technique for real-time monitoring of critical performance attributes in large scale processes and is ideally suited for dewatering applications. The flocculation performance of twenty-four cationic polymers, that spanned a range of polymer size and charge properties, was measured using both the FBRM and CST tests. Analysis of the data revealed a decreasing monotonic trend; the samples that had the highest percent removal of particles less than 50 microns in size as determined by FBRM had the lowest CST values. A subset of the best performing polymers was used to evaluate the effects of dosage amount and digestate sources on dewatering performance. The results from this work show that FBRM is a powerful tool that can be used for optimization and on-line monitoring of dewatering processes. Copyright © 2014 Elsevier Ltd. All rights reserved.

Laboratory and field experience with rim ditch dewatering of MFT

Energy Technology Data Exchange (ETDEWEB)

Demoz, A.; Mikula, R. [Natural Resources Canada, Devon, AB (Canada). CANMET Western Research Centre; Lahaie, R. [Syncrude Canada Ltd., Edmonton, AB (Canada)

2010-07-01

This PowerPoint presentation described a rim ditch method of dewatering mature fine tailings (MFT). Polymer additions were used to strengthen the MFT and to decrease the capillary suction time (CST). Laboratory and field-scale studies were conducted to demonstrate the dewatering method. The flocculants were added in a Komax inline mixer. Polymers were then injected into the tailings. The mixing processes were optimized in a series of laboratory studies and then demonstrated in the field tests. The tests showed that CST and high dewatering rates were consistently maintained using the method. MFT feeds were also consistent. Release water quality was improved using the method. The large-scale test site is now being monitored for compliance with Directive 74. tabs., figs.

Osmotic Effects in Sludge Dewatering

DEFF Research Database (Denmark)

Keiding, Kristian; Rasmussen, Michael R.

2003-01-01

A model of filtration dewatering is presented. The model is based on the d’Arcy flow equation in which the resistance to filtration is described by the Corzeny–Carman equation and the driving force is the difference between the external pressure and the osmotic pressure of the filter cake. It has...

Monitoring and optimizing the co-composting of dewatered sludge: a mixture experimental design approach.

Science.gov (United States)

Komilis, Dimitrios; Evangelou, Alexandros; Voudrias, Evangelos

2011-09-01

The management of dewatered wastewater sludge is a major issue worldwide. Sludge disposal to landfills is not sustainable and thus alternative treatment techniques are being sought. The objective of this work was to determine optimal mixing ratios of dewatered sludge with other organic amendments in order to maximize the degradability of the mixtures during composting. This objective was achieved using mixture experimental design principles. An additional objective was to study the impact of the initial C/N ratio and moisture contents on the co-composting process of dewatered sludge. The composting process was monitored through measurements of O(2) uptake rates, CO(2) evolution, temperature profile and solids reduction. Eight (8) runs were performed in 100 L insulated air-tight bioreactors under a dynamic air flow regime. The initial mixtures were prepared using dewatered wastewater sludge, mixed paper wastes, food wastes, tree branches and sawdust at various initial C/N ratios and moisture contents. According to empirical modeling, mixtures of sludge and food waste mixtures at 1:1 ratio (ww, wet weight) maximize degradability. Structural amendments should be maintained below 30% to reach thermophilic temperatures. The initial C/N ratio and initial moisture content of the mixture were not found to influence the decomposition process. The bio C/bio N ratio started from around 10, for all runs, decreased during the middle of the process and increased to up to 20 at the end of the process. The solid carbon reduction of the mixtures without the branches ranged from 28% to 62%, whilst solid N reductions ranged from 30% to 63%. Respiratory quotients had a decreasing trend throughout the composting process. Copyright © 2011 Elsevier Ltd. All rights reserved.

Co-conditioning and dewatering of chemical sludge and waste activated sludge.

Science.gov (United States)

Chang, G R; Liu, J C; Lee, D J

2001-03-01

The conditioning and dewatering behaviors of chemical and waste activated sludges from a tannery were studied. Capillary suction time (CST), specific resistance to filtration (SRF), and bound water content were used to evaluate the sludge dewatering behaviors. Zeta potentials were also measured. Experiments were conducted on each sludge conditioned and dewatered separately, and on the sludge mixed at various ratios. Results indicate that the chemical sludge was relatively difficult to be dewatered, even in the presence of polyelectrolyte. When the waste activated sludge was mixed with the chemical sludge at ratios of 1:1 and 2:1, respectively, the dewaterability of chemical sludge improved remarkably while the relatively better dewaterability of the waste activated sludge deteriorated only to a limited extent. As the mixing ratios became 4:1 and 8:1, the dewaterability of the mixed sludge was equal to that of the waste activated sludge. The optimal polyelectrolyte dosage for the mixed sludge was equal to or less than that of the waste activated sludge. It is proposed that the chemical sludges act as skeleton builders that reduce the compressibility of the mixed sludge whose dewaterability is enhanced. Bound water contents of sludge decreased at low polyelectrolyte dosage and were not significantly affected as polyelectrolyte dosage increased. Advantages and disadvantages of co-conditioning and dewatering chemical sludge and waste activated sludge were discussed.

46 CFR 28.255 - Bilge pumps, bilge piping, and dewatering systems.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Bilge pumps, bilge piping, and dewatering systems. 28... the Aleutian Trade § 28.255 Bilge pumps, bilge piping, and dewatering systems. (a) Each vessel must be equipped with a bilge pump and bilge piping capable of draining any watertight compartment, other than...

Synthesis, characterization, and secondary sludge dewatering performance of a novel combined silicon–aluminum–iron–starch flocculant

Energy Technology Data Exchange (ETDEWEB)

Lin, Qintie, E-mail: qintlin@163.com; Peng, Huanlong; Zhong, Songxiong; Xiang, Jiangxin

2015-03-21

Highlights: • Silicon, aluminum, and iron were grafted onto starch chains to synthesize CSiAFS. • The sludge dewatering performance of CSiAFS was superior to PAC, PAM, and FeCl{sub 3}. • CSiAFS exhibited a good dewatering efficiency over a wide range of pH (3.0–11.0). • CSiAFS had a discontinuous surface with channels which helped to sludge dewatering. - Abstract: Flocculation is one of the most widely used cost-effective pretreatment method for sludge dewatering, and a novel environmentally friendly and efficient flocculant is highly desired in the sludge dewatering field. In this study, a novel combined silicon–aluminum–ferric–starch was synthesized by grafting silicon, aluminum, and iron onto a starch backbone. The synthesized starch flocculant was characterized using Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy, X-ray powder diffraction, and thermogravimetric analysis. The dewatering performance of secondary sludge was evaluated according to the capillary suction time, settling volume percentage, and specific resistance to filtration. The results indicated that the copolymer exhibited: (1) a good dewatering efficiency over a wide pH range of 3.0–11.0, (2) superior sludge dewatering performance compared to those of polyaluminum chloride (PACl), polyacrylamide (PAM), ferric chloride, and (3) a discontinuous surface with many channels or voids that helps to mobilize the impermeable thin layer of secondary sludge during filter pressing. Such a novel copolymer is a promising green flocculant for secondary sludge dewatering applications.

Design of the Nonlinear Pin Rubber Forming Equipment Integrating the Functions of Extruding, Dewatering, Drying & Expanding

Directory of Open Access Journals (Sweden)

Yuefeng Yuan

2014-12-01

Full Text Available The top priority of car-tire suppliers is to improve wetland grip force of the using tires, reduce the rolling resistance and the rolling noise of tires. It is urgent for the tire industry to research and develop high-performance tires to solve the above problems. They must use the high- performance synthetic rubber and auxiliary rubber to develop the most advanced manufacturing technologies and equipment. Silica, a kind of important tire auxiliary rubber, can significantly reduce the rolling resistance of tires, improve the grip force and properties resistant to ice, wetness or slippery of tires. In this paper, based on the conventional tire rubber forming technologies of extrusion, dewatering, drying and expanding, a study is made on the conical screw, the dewatering barrel, the drying barrel, the pin layout scheme, the expanding die head, cutter and the control system. The nonlinear pin rubber forming equipment integrating the functions of extrusion, dewatering, drying and expanding is designed and applied to tire auxiliary rubber forming. The experiment shows that the forming device can realize the one-step forming, with high forming efficiency, low cost and less labor.

Effect of hydrothermal dewatering on the slurryability of brown coals

International Nuclear Information System (INIS)

Yu Yujie; Liu Jianzhong; Wang Ruikun; Zhou Junhu; Cen Kefa

2012-01-01

Highlights: ► Brown coals are upgraded by hydrothermal dewatering. ► The moisture content and oxygen functional groups decrease during the process. ► The point of zero charge and the contact angle rise as the temperature increases. ► The products were highly hydrophobic. ► The improvement on slurryability of solid products were examined. - Abstract: Two brown coals from China were dewatered under hydrothermal dewatering (HTD) conditions at 250–320 °C for 1 h in a 2 L autoclave. The hydrothermally dewatered products were used to prepare coal water slurry (CWS) with a lower viscosity than brown raw coal slurry. Moreover, the coal rank and heat value of the brown coal increased as the inherent moisture and oxygen content decreased during the HTD process. The maximum solid concentration of CWS prepared from XiMeng coal increased from 45.7% to 59.3%, whereas that of CWS prepared from BaoTou coal increased from 53.7% to 62.1%, after being dewatered at 320 °C. The improvement in the slurryability of brown coal significantly depended on the final temperature of the HTD process, the mechanism of which can be explained by the chemical analysis of oxygen functional groups, zeta potential, and the contact angle of the surface between coal and water. The oxygen functional groups, the oxygen/carbon ratio and hydrogen/carbon ratio in brown coal decreased, indicating that the coal rank was upgraded during the HTD process. As a result, both the point of zero charge and the contact angle increased, implying that the HTD products were highly hydrophobic.

Dewatering of planned Key Lake open pits in northern Saskatchewan

International Nuclear Information System (INIS)

Unland, W.; Holl, N.

1980-01-01

The engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan are presented. An extensive unconfined overburden aquifer is hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. Hydrogeological data were used in a numerical dewatering model simulating groundwater flow at different stages of the pit development. Based on the model results, the enginering design had to provide for different pumping rates, varying between 1.0 and 0.21 m 3 /sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26 dewatering wells are discussed. (auth)

Centrifuge - dewatering of oil sand fluid tailings: phase 2 field-scale test

Energy Technology Data Exchange (ETDEWEB)

Seto, Jack T.C. [BGC Engineering Inc (Canada); O' Kane, Mike [O' Kane Consultants Inc (Canada); Donahue, Robert [Applied Geochemical Solutions Engineering (Canada); Lahaie, Rick [Syncrude Canada Ltd (Canada)

2011-07-01

In order to reduce the accumulation of oil sand fluid fine tailings (FFT) and to create trafficable surfaces for reclamation, Syncrude Canada Ltd. has been studying several tailings technologies. Centrifuge-dewatering is one such technology. This paper discusses the phase 2 field-scale tests for centrifuge-dewatering of oil sand FFT. In centrifuge-dewatering, FFT is diluted and treated with flocculant, then processed through a centrifuge plant and the high-density underflow is transported to a tailings deposit. This technology has evolved since 2005 from laboratory bench scale tests. More than 10,000 cubic meters of centrifuge cake was treated, produced and transported to ten different deposits over a 12-week period from August to October 2010. The amount of solids in FFT was increased from 30% to 50% by centrifuging. Sampled deposits were tested and instrumented for in situ strength. It can be concluded that the deposits can be strengthened and densified by natural dewatering processes like freeze-thaw action and evaporative drying.

Field performance of de-watered fluid fine tailings for oil sands reclamation

Energy Technology Data Exchange (ETDEWEB)

Ward Wilson, G.; Kabwe, Louis [University of Alberta (Canada); Donahue, Robert [Applied Geochemical Engineering Inc. (Canada); Lahaie, Rick [Syncrude Canada Ltd (Canada)

2011-07-01

This document presents research carried out by Syncrude Canada Ltd and its partners to evaluate several methods of de-watering fluid fine tailings to increase the solids content and at the same time produce a tailings profile which will permit final reclamation. Several de-watering methods are discussed in this paper, particularly in-line flocculation and centrifuged fluid fine tailings. First, in-line flocculation with organic polymers is discussed followed by thin left deposition, then the flocculation and centrifugation process to produce a paste- like material that is deposited in a thicker layer is presented. This document details the preliminary performance of both discussed methods; extensive instrumentation was used to measure de-watering rates due to consolidation, atmospheric drying, downward drainage to the foundation materials, and freeze/thaw consolidation. Finally, a summary of the measured results of de-watering rates and numerical model results obtained from the SoilCover model are presented and discussed.

METODE PELAKSANAAN DEWATERING YANG RAMAH LINGKUNGAN PADA PROYEK THE NEST CONDOTEL

Directory of Open Access Journals (Sweden)

I Wayan Intara

2016-03-01

Full Text Available Proyek Pembangunan The Nest Condotel merupakan salah satu upaya untuk memenuhi sarana dan prasarana pariwisata khusunya daerah Nusa Dua-Bali. Proyek ini dibangun di tengah-tengah pemukiman penduduk dan berdekatan dengan Pengolahan Limbah BTDC. Setelah dilaksanakan survei lapangan ada permasalahan yang dihadapi pada pembangunan proyek ini yaitu pada pengerjaan struktur basement. Kondisi muka air tanah lebih tinggi daripada rencana pemukaan galian lantai basement yang akan dibuat. Di samping itu, kondisi tanah yang kurang baik dengan kondisi tanah yang berpasir. Berdasarkan permasalahan di atas perlu adanya pemilihan perencanaan metode penanganan muka air tanah yang paling tepat dalam pekerjaan  galian basement. Dewatering adalah proses penurunan muka air tanah pada suatu area tertentu dengan cara pemompaan dari sebuah sumur ataupun saluran. Tujuannya adalah untuk menjaga area galian tetap kering dalam proses konstruksi dan menjaga kestabilan lereng galian. Pemompaan dilakukan melalui sumur-sumur dewatering (dewatering well atau well point atau saluran-saluran (sump dengan menggunakan pompa submersible (submersible pump. Dengan demikian penggalian basement bisa dikerjakan dengan baik. Penelitian ini adalah menentukan metode pelaksanaan pekerjaan dewatering yang paling tepat dari metode-metode pelaksanaan yang mungkin untuk dilaksankan berdasarkan biaya, waktu, dan dampak terhadap lingkungan. Metodelogi yang digunakan untuk analisis data adalah menganalisis metode-metode pelaksanaan yang ada dan dari hasil analisis akan ditetapkan metode pelaksanaan terbaik. Hasil analisis dari beberapa metode pelaksanaan yang ada untuk pekerjaan dewatering digunakan adalah predrainage dan open pumping, metode yang terpilih yaitu open pumping adalah metode terbaik untuk dilaksanakan pada proyek tersebut dengan biaya yang terendah, waktu pelaksanaan yang lebih cepat, dan dampak lingkungan yang dapat diminimalisir

Dewatering of Yoghurt Using Permeable Membrane and Acrylic Superabsorbent Hydrogel

Directory of Open Access Journals (Sweden)

A. Ahmadpour

2008-02-01

Full Text Available Conventional processes of food dewatering, such as thermal, have undesirable and destruction effects on vitamins, aromatic compounds and pigments. In addition, they are accompanied with some technological complications and energy consumption. Thus, food concentration processes are directed to non-thermal techniques or methods with reduced heat effects. Superabsorbents are highly hydrophilic polymer networks which can absorb water and aqueous solutions some hundred times of their weights and retain them. These materials are subgroups of hydrogel family that are transformed into gels after absorbing water. In the present research, the possibilities of yoghurt dewatering using superabsorbents have been investigated for the first time in Iran and some remarkable results are obtained for this vital product. In the experiments carried out to investigate the effect of these absorbents on normal method of yoghurt concentration (use of permeable membrane, type of bed (wide and vertical and time are also studied. The percentage of total soluble solids and dry solids of dewatered samples were measured in different time intervals up to 180 min. The results showed that superabsorbent on a wide bed would reduce the concentration time to one third. In other words, in a certain time interval, more than 70% increase in yoghurt dry solids was observed compared to normal method. These results show that acrylic superabsorbent hydrogel can be applied as highly hydrophilic material in non-thermal food dewatering methods.

Permanganate/bisulfite (PM/BS) conditioning-horizontal electro-dewatering (HED) of activated sludge: Effect of reactive Mn(III) species.

Science.gov (United States)

Guo, Xinxin; Wang, Yili; Wang, Dongsheng

2017-11-01

A novel activated sludge (AS) conditioning method through permanganate/bisulfate (PM/BS) process was proposed. The method involved a new conditioner of reactive Mn(III) intermediate. Moreover, a Mn(III) conditioning-horizontal electro-dewatering (Mn(III) C-HED) process was established to improve AS dewatering performance. Underlying mechanisms were unraveled by investigating changes in physicochemical characteristics, scanning electron microscope (SEM) morphology, and transformation of water and organic matters. The optimum dewatering conditions for Mn(III) C-HED process with the final water content of 86.94% were determined as the combination of KMnO 4 0.01 mol/L AS and NaHSO 3 0.05 mol/L AS at 20 V for 120 min. Results showed that Mn(III) C-HED process effectively reduced free water and bound water with the corresponding removal ratios of 51.68% and 87.62% at the anode-side as well as 36.55% and 85.08% at the cathode-side, respectively. During the PM/BS process, the produced Mn(III), Mn 2+ , and MnO 2 exerted chemical and physical effects on AS conditioning and dewatering. Mn(III) disintegrated extracellular polymeric substances (EPS) fractions and cells in AS, as well as induced partial bound water release. Additionally, flocculation effect induced by Mn 2+ and MnO 2 skeleton building also benefited AS dewatering. AS cells were further disrupted under the effect of a horizontal electric field. Accordingly, EPS within the AS matrix was solubilized, tightly bound (TB)-EPS or loosely bound (LB)-EPS was converted to their corresponding outer EPS fractions, and AS dewaterability improved. Additionally, changes in pH and temperature at HED stage damaged the AS cells and changed the floc properties, thereby leading to easy separation of liquid and AS particles. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterization and dewatering of flotation technological tailings

Directory of Open Access Journals (Sweden)

Grigorova I.

2014-01-01

Full Text Available The treatment of flotation tailings is today a subject of interest in mineral processing because of the potential of wasted materials as an actual mineral resource and because of environmental reasons. Decantation ponds are found at almost every mine in the world. They are large earth fill dams containing the residue of the milling process to extract metals from mined ores. Traditional wet tailings disposal has been problematic due to the risk of ground water contamination and the difficulty in rehabilitating storage sites. Tailings dams are at risk of failure due to leakage, instability, liquefaction, and poor design. In the last few years the use of paste technology in the disposal of mine tailings is increasingly studied as an option to conventional tailings dams. The Lucky Invest Concentrator is located in the Eastern Rhodopes Mountain of Bulgaria. Since 1959 lead-zinc ores are dressed. Finally, during the flotation cycle lead and zinc concentrates are produced. The final technological processing waste precipitates in tailing pond. Research and development program has started to established opportunities to obtain dry deposit of the ore processing residue and analyses the feature of new tailing disposal method. The tailings particle size distributions and chemical compositions were determined. The data from laboratory and pilot scale tests clearly illustrate that there are the possibilities to obtaine lead-zinc dewatered tailings. The experimental results show that new cyclone modifications have a potential in dewatering technology of flotation tailings. It appears that dewatering cyclones can be an approach on new tailings pond elimination technology.

Application of a thermally assisted mechanical dewatering process to biomass

Energy Technology Data Exchange (ETDEWEB)

Mahmoud, A.; Arlabosse, P. [Universite de Toulouse, Mines Albi, CNRS, Campus Jarlard, F-81013 Albi cedex 09 (France); Ecole des Mines Albi, Centre RAPSODEE, Campus Jarlard, F-81013 Albi (France); Fernandez, A. [Universite de Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F-31400 Toulouse (France); INRA, UMR792 Ingenierie des Systemes Biologiques et des Procedes, CNRS, UMR5504, F-31400 Toulouse (France)

2011-01-15

Thermally assisted mechanical dewatering (TAMD) is a new process for energy-efficient liquid/solids separation which enhances conventional-device efficiency. The main idea of this process is to supply a flow of heat in mechanical dewatering processes to favour the reduction of the liquid content. This is not a new idea but the proposed combination, especially the chosen operating conditions (T < 100 C and P < 3000 kPa) constitutes an original approach and a significant energy saving since the liquid is kept in liquid state. Response surface methodology was used to evaluate the effects of the processing parameters of TAMD on the final dry solids content, which is a fundamental dewatering parameter and an excellent indicator of the extent of TAMD. In this study, a two-factor central composite design was used to establish the optimum conditions for the TAMD of alfalfa biomass. Experiments were carried out on a laboratory compression cell. Experiments showed that the dewatering enhancement results only from thermal effects. With a moderate heat supply (T{sub piston} = 80 C), the dry solid content of the press cake can reach 66%, compared to 36% at ambient temperature. A significant regression model, describing changes on final dry solids content with respect to independent variables, was established with determination coefficient, R{sup 2}, greater than 88%. With an energy consumption of less than 150 kWh/m{sup 3}, the use of the TAMD process before a thermal drying process leads to an energy saving of at least 30% on the overall separation chain. (author)

Electroosmotically enhanced dewatering/deliquoring of fine-particle coal: Final report, January 1--December 31, 1988

Energy Technology Data Exchange (ETDEWEB)

Sami, Sedat [Department of Civil Engineering and Mechanics, Southern Illinois Univ., Carbondale, IL (United States); Davis, Philip K. [Department of Civil Engineering and Mechanics, Southern Illinois Univ., Carbondale, IL (United States); Smith, James G. [Department of Electrical Engineering, Southern Illinois Univ., Carbondale, IL (United States)

1989-03-01

This research is an investigation of the use of electroosmosis to dewater/deliquor ultrafine coal. Post-beneficiation dewatering/deliquoring methods for ultrafine coal are inadequate and generally require subsequent thermal drying. Thermal drying is not only expensive and time consuming, it also does not recover liquids for reuse in beneficiation processes. The degree of difficulty associated with dewatering increases as surface forces become more important than gravimetric forces. Electroosmotic flow has advantages for dewatering because it is much less sensitive to pore size than hydraulic gradient flow for the 1 to 75 ..mu..m ultrafine size range. The first year of this project focused upon preparation of ultrafine coal samples, development of test equipment and test cells, identification of variables affecting electroosmosis, and trial runs. Techniques and procedures not previously used by researchers of electroosmotic dewatering have revealed important information about the dynamics of the electroosmosis process. The identification of the first few millimeters of the cathode region of the cell as the sink for most of the energy input into the process provides the potential for improving efficiency by concentrating the second year effort on intervention in that region. Information gathered about differences in FTIR spectra as a function of location in the dewatering cell will be investigated. Changes in pH with temperature and by the application of electroosmotic current flow will receive attention, as well. 178 refs., 16 figs.

Hot dewatering and resin encapsulation of intermediate level radioactive waste

International Nuclear Information System (INIS)

Rickman, J.; Birch, D.

1985-01-01

The chemistry of the processes involved in the hot dewatering and encapsulation of alumino-ferric hydroxide floc in epoxide resin have been studied. Pretreatment of the floc to reduce resin attack and hydrolysis and to increase the dimensional stability of the solidified wasteform has been evaluated. It has been demonstrated that removal of ammonium nitrate from the floc and control of the residual water in the resin are important factors in ensuring dimensional stability of the solidified resin. Resin systems have been identified which, together with the appropriate waste pretreatment have successfully encapsulated a simulated magnox sludge producing a stable wasteform having mechanical and physical properties comparable with the basic resin. (author)

A new dewatering technique for stingless bees honey

Directory of Open Access Journals (Sweden)

Ramli Ahmad Syazwan

2017-01-01

Full Text Available One of the problems faced in stingless bee honey storage is spoilage by the fermentation process occurs in honey due to its high water content. There are a few techniques available currently, but they are time consuming and there is excessive heat involved in the process. The temperature of the process must be kept low because excessive heat can deteriorate nutrition value and biochemical content in honey. Hence, a new method of honey dewatering was developed using a Low Temperature Vacuum Drying (LTVD with induced nucleation technique.The objective of this research is to investigate the performance of a LTVD with induced nucleation to reduce the water content in honey. First, the honey was placed in a pressure vessel, and then air was removed. Then, the honey was slightly heated at 30°C and the water content before and after the experiment was measured by a refractometer. The steps were repeated until the water content reached below 20%. It was found that the LTVD method improved the water removal rate significantly with an average of 0.15% of water content per minute. That is 3 times much faster than the conventional method of low temperature heating by Tabouret. Higher temperature during dewatering process improved the dewatering rate significantly. It can be concluded that LTVD is a promising option in tackling the high water content in stingless bee honey issue.

105-N Fuel Storage Basin dewatering conceptual plan

International Nuclear Information System (INIS)

Schilperoort, D.L.

1996-11-01

This conceptual plan discusses the processes that will be used for draining and disposing of water from the 105-N Fuel Storage Basin (N Basin), and includes a description of the activities to control surface contamination and potential high dose rates encountered during dewatering. The 105-N Fuel Storage Basin is located in the 100-N Area of the Hanford Site in Richland, Washington. The processes for water disposal include water filtration, water sampling and analysis, tanker loading and unloading, surface decontamination and sealing, and clean out and disposal of residual debris and sediments during final pumping to remove the N Basin water. Water disposal is critical for the deactivation of N Reactor. A Memorandum of Understanding (MOU) between the US Department of Energy (DOE) Environmental Restoration (ER) Program and DOE Waste Management (WM) Program establishes the 200 East Effluent Treatment Facility (ETF) as the final treatment and disposal site for N Basin water and identifies pre-treatment requirements. This MOU states that water delivery will be completed no later than October 31, 1996, and will require a revision due to the current de-watering schedule date. The current MOU requires four micron filtration prior to shipment to ETF. The MOU revision for delivery date extension seeks to have the filtration limit increased to five microns, which eliminates the need for a second filter system and simplifies dewatering. For the purposes of this plan, it will be assumed that five micron filtration will be used

Reconstitution of dewatered food processing residuals with manure to increase energy production from anaerobic digestion

International Nuclear Information System (INIS)

Wall, David M.; Wu-Haan, Wei; Safferman, Steven I.

2012-01-01

Solid residuals generated from dewatering food processing wastewater contain organic carbon that can potentially be reclaimed for energy through anaerobic digestion. This results in the diversion of waste from a landfill and uses it for a beneficial purpose. Dewatering the waste concentrates the carbon, reducing transportation costs to a farm digester where it can be blended with manure to increase biogas yield. Polymers are often used in the dewatering of the food waste but little is known regarding their impact on biogas production. Four 2 dm 3 working volume, semi-continuous reactors, were used at a mesophilic temperature and a solids retention time (SRT) of 15 days. Reactors were fed daily with a blended feedstock containing a food processing sludge waste (FPSW)/manure ratio of 2.2:1 (by weight) as this produced the optimized carbon to nitrogen ratio. Results demonstrated that reconstitution of dewatered FPSW with dairy manure produced approximately 2 times more methane than animal manure alone for the same volume. However, only approximately 30% of volatile solids (VS) were consumed indicating energy potential still remained. Further, the efficiency of the conversion of VS to methane for the blended FPSW/manure was substantially less than for manure only. However, the overall result is an increase in energy production for a given tank volume, which can decrease life cycle costs. Because all FPSW is unique and the determination of dewatering additives is customized based on laboratory testing and field adjustment, generalizations are difficult and specific testing is required. -- Highlights: ► Energy production in anaerobic digestion can increase by co-blending food waste. ► Energy for transporting food waste to blend with manure is less when dewatered. ► Dewatered food waste in manure produced twice as much methane than manure. ► Efficiency of carbon to methane was low because of ammonium bicarbonate production. ► Carbon destruction was 30%, more

An experimental investigation of microalgal dewatering efficiency of belt filter system

Directory of Open Access Journals (Sweden)

Anjali Sandip

2015-11-01

Full Text Available The objective of this study was to investigate the microalgal dewatering efficiency of a belt filter system for feed concentrations below 10 g dry wt./L. A prototype belt filtration system designed for 50 g dry wt./L microalgal feed concentration was used for this investigation. The highest concentration of microalgal suspension available for testing on the prototype belt filtration system was 6 g dry wt./L obtained from biomass settling tanks at the Lawrence, Kansas domestic wastewater treatment plant. For preparation of feed suspension with concentrations below 10 g dry wt./L, microalgal cultivation was followed by flocculation. A mixed laboratory culture of freshwater species dominated by three eukaryotic green microalgae (Chlorella vulgaris, Scenedesmus sp., and Kirchneriella sp. was cultivated in wastewater effluent. This was followed by flocculation which resulted in a microalgal feed suspension concentration of 4 g dry wt./L. Belt dewatering tests were conducted on microalgal suspensions with feed concentrations of 4 g dry wt./L and 6 g dry wt./L. The maximum microalgal recovery with the belt dewatering system was 46% from the 4 g dry wt./L, and 84% from the 6 g dry wt./L suspensions respectively. The results of this study indicate that microalgal suspension concentrations as low as 6 g dry wt./L can be recovered with a belt filter system improving the overall dewatering efficiency of the system.

Tectonic controlled submarine slidings and dewatering structures

Science.gov (United States)

Yamamoto, Y.; Hirono, T.; Takahashi, M.

2003-04-01

Geologic structures associated with mass movements processes such as slumping, sliding, and creeping can be the key to understanding the tectonic or geologic constraints in the time they were formed. Because they are sensitively reflected by the paleo-topography which must be associated with active tectonics. It must be very useful if the direction of paleo-slope instability is known easily in a wide area. We paid attentions to convolute lamination and flame structure which might be associated with dewatering and loading, respectively. Some recent researches report the possibility that well regulated flame structures might be formed in relation to paleo-slope instability. However, there is an alternative idea that they were reflection of heterogeneous loading associated with ripple marks on the sandy layers. This controversy has not been settled. Accordingly, to evaluate the reliability of the relationship between formation of such structures with well regulated arrays and paleo-slope instability, the Pliocene Chikura Group in the southern part of the Boso Peninsula, central Japan, was studied. The Chikura Group overlying the Miura Group, Miocene accretionary prism, is composed of trench-fill sediments in the lowermost and of trench-slope basin sediments in the upper. The Chikura Group was deposited on an east-west extended sedimentary basin during east-west trending folds and faults development. These indicate the direction of paleo-slope in the Chikura Group due north or south. Flame structures and convolute laminations were recognized over 60 sites in the Chikura Group. They have well-regulated planar arrays which extend almost east west, perpendicular to the direction of paleo-slope instability. Some examples of such structures and slump deposit were observed in the same outcrop. Vergence of these slump deposits were toward north or south, and ridges of flame structures and convolute laminations extend east-west. Experimental study of direct imaging of

Field Evaluation/Demonstration of a Multisegmented Dewatering System for Accreting Beach Sand in a High-Wave-Energy Environment

National Research Council Canada - National Science Library

Curtis, William

1998-01-01

This study documents the use of beach dewatering systems to accrete beach sand and minimize erosion, and to develop quantitative guidance for constructing and operating beach dewatering installations...

Dewatering cuts drilling mud and disposal costs

International Nuclear Information System (INIS)

West, G.; Pharis, B.

1991-01-01

This paper reports on rig site dewatering of drilling fluids with recycling of processed water that can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Rig site dewatering is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. This coagulates the fine, drilled particles allowing them to be separated from the fluid which can then be handled separately. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste

The exploitation of swamp plants for dewatering liquid sewage sludge

Directory of Open Access Journals (Sweden)

Jiří Šálek

2006-01-01

Full Text Available The operators of little rural wastewater treatment plants have been interested in economic exploitation of sewage sludge in local conditions. The chance is searching simply and natural ways of processing and exploitation stabilized sewage sludge in agriculture. Manure substrate have been obtained by composting waterless sewage sludge including rest plant biomass after closing 6–8 years period of filling liquid sewage sludge to the basin. Main attention was focused on exploitation of swamp plants for dewatering liquid sewage sludge and determination of influence sewage sludge on plants, intensity and course of evapotranspiration and design and setting of drying beds. On the base of determined ability of swamp plants evapotranspiration were edited suggestion solutions of design and operation sludge bed facilities in the conditions of small rural wastewater treatment plant.

Synergetic pretreatment of waste activated sludge by hydrodynamic cavitation combined with Fenton reaction for enhanced dewatering.

Science.gov (United States)

Cai, Meiqiang; Hu, Jianqiang; Lian, Guanghu; Xiao, Ruiyang; Song, Zhijun; Jin, Micong; Dong, Chunying; Wang, Quanyuan; Luo, Dewen; Wei, Zongsu

2018-04-01

The dewatering of waste activated sludge by integrated hydrodynamic cavitation (HC) and Fenton reaction was explored in this study. We first investigated the effects of initial pH, sludge concentration, flow rate, and H 2 O 2 concentration on the sludge dewaterability represented by water content, capillary suction time and specific resistance to filtration. The results of dewatering tests showed that acidic pH and low sludge concentration were favorable to improve dewatering performance in the HC/Fenton system, whereas optimal flow rate and H 2 O 2 concentration applied depended on the system operation. To reveal the synergism of HC/Fenton treatment, a suite of analysis were implemented: three-dimensional excitation emission matrix (3-DEEM) spectra of extracellular polymeric substances (EPS) such as proteins and polysaccharides, zeta potential and particle size of sludge flocs, and SEM/TEM imaging of sludge morphology. The characterization results indicate a three-step mechanism, namely HC fracture of different EPS in sludge flocs, Fenton oxidation of the released EPS, and Fe(III) re-flocculation, that is responsible for the synergistically enhanced sludge dewatering. Results of current study provide a basis to improve our understanding on the sludge dewatering performance by HC/Fenton treatment and possible scale-up of the technology for use in wastewater treatment plants. Copyright © 2017 Elsevier B.V. All rights reserved.

Upgrading of brown coal by slurry-dewatering; Kattan no yuchu dassui ni yoru clean kotai nenryo no seizo

Energy Technology Data Exchange (ETDEWEB)

Okuma, O.; Shimizu, T.; Inoue, T.; Shigehisa, T.; Deguchi, T.; Katsushima, S. [Kobe Steel, Ltd., Kobe (Japan)

1996-10-28

This paper describes an outline of solid fuel production process from brown coal and the investigation results of its elemental techniques. Dried coal is produced by this process which consists of a dewatering of crushed brown coal in oil-based solvent, a solid and liquid separation of slurry, and a remained oil recovery by heating. This process is characterized by the higher thermal efficiency compared with usual drying and the restraint of spontaneous combustion of product coal. It was revealed that solid fuel with low moisture, low ash, low sulfur, and suppressed spontaneous combustion property can be produced from Australian brown coal through this process. From the comparison between kerosene and fuel oil A, it was confirmed that the oil content during dewatering was smaller and the oil recovery by heating was easier by using a solvent with lower boiling point. It was also confirmed that the spontaneous combustion property can be suppressed using small amount of asphalt by solving asphalt in the solvent and adsorbing asphalt on the surface of brown coal. From these results, low rank coals including brown coal, which are difficult to use, are expected to be used as clean coal with low ash and low sulfur through this process. 2 refs., 7 figs., 2 tabs.

Ecotoxicological assessment of dewatered drinking water treatment residue for environmental recycling.

Science.gov (United States)

Yuan, Nannan; Wang, Changhui; Wendling, Laura A; Pei, Yuansheng

2017-09-01

The beneficial recycle of drinking water treatment residue (DWTR) in environmental remediation has been demonstrated in many reports. However, the lack of information concerning the potential toxicity of dewatered DWTR hinders its widespread use. The present study examined the ecotoxicity of dewatered aluminum (Al) and iron (Fe) DWTR leachates to a green alga, Chlorella vulgaris. Data from the variations of cell density and chlorophyll a content suggested that algal growth in DWTR leachates was inhibited. The algal cellular oxidation stress was initially induced but completely eliminated within 72 h by antioxidant enzymes. The expression of three photosynthesis-related algae genes (psaB, psbC, and rbcL) also temporarily decreased (within 72 h). Moreover, the algal cells showed intact cytomembranes after exposure to DWTR leachates. Further investigation confirmed that inhibition of algal growth was due to DWTR-induced phosphorus (P) deficiency in growth medium, rather than potentially toxic contaminants (e.g. copper and Al) contained in DWTR. Interestingly, the leachates could potentially promote algal growth via increasing the supply of new components (e.g. calcium, kalium, magnesium, and ammonia nitrogen) from DWTR. In summary, based on the algae toxicity test, the dewatered Fe/Al DWTR was nontoxic and its environment recycling does not represent an ecotoxicological risk to algae.

Pervaporation applied for dewatering of reaction mixture during esterification

Directory of Open Access Journals (Sweden)

Krasiński Andrzej

2016-03-01

Full Text Available In this work the esterification of diethyl tartrate was studied. The research was focused on the enhancement of reversible reaction yield, which is accomplished by dewatering of the reaction mixture. The removal of water shifts the equilibrium towards the main product. Pervaporation was applied for this purpose, and results were compared to distillation. The advantages and limitations of both processes are discussed. The experimental part consists of dewatering of mixture after the reaction had reached the equilibrium, and was subsequently fed to the test rig equipped with a single zeolite membrane purchased from Pervatech B.V. Results show a significant conversion increase as a result of water removal by pervaporation. Compared to distillation no addition of organics is necessary to efficiently remove water above the azeotrope. Nevertheless, some limitations and issues which call for optimisation are pointed out. A simple numerical model is proposed to support design and sizing of the pervaporation system. Various modes of integrated system operation are also briefly discussed.

Centrifugal dewatering of acid casein curd: effect of casein manufacturing and centrifugation variables on curd compression in a laboratory centrifuge.

Science.gov (United States)

Munro, P A; Van Til, H J

1988-10-20

Data relevant to curd compression in a horizontal, solid bowl decanter centrifuge have been obtained by studying the dewatering of acid casein curd in a batch laboratory centrifuge. Analysis of curd compression under centrifugal force predicts a moisture content gradient in the dewatered curd from a maximum at the curd-liquid interface to a minimum at the centrifuge bowl wall. This moisture content gradient was also measured experimentally, and its practical implications are discussed. Increases in centrifugal force, centrifugation time, and centrifugation temperature all caused a marked de crease in dewatered curd moisture content, whereas in creases in precipitation pH and maximum washing temperature caused a smaller decrease in dewatered curd moisture content.

Dewatering tailings impoundments : interior drains

International Nuclear Information System (INIS)

Charlie, W.A.; Doehring, D.O.; Durnford, D.S.

1984-01-01

For the design of a new uranium tailings impoundment in the western United States, it was proposed that an interior drainage system be considered to economically and reliably minimize potential short- and long-term environmental impacts. The objectives were to decrease the effective hydraulic head on the clay liner, to dewater and stabilize the tailings, and to increase the amount of water recycled to the mill. In addition, desaturation of the impoundment would induce capillary pressure (negative porewater pressure), further reducing the potential movement of dissolved pollutants. This paper presents saturated and unsaturated seepage principles and reviews the concept, criteria and design of the various interior drainage systems considered

Locally produced natural conditioners for dewatering of faecal sludge.

Science.gov (United States)

Gold, Moritz; Dayer, Pauline; Faye, Marie Christine Amie Sene; Clair, Guillaume; Seck, Alsane; Niang, Seydou; Morgenroth, Eberhard; Strande, Linda

2016-11-01

In urban areas of low-income countries, treatment of faecal sludge (FS) is insufficient or non-existent. This results in large amounts of FS being dumped into the environment. Existing treatment technologies for FS, such as settling-thickening tanks and drying beds, are land intensive which is limiting in urban areas. Enhanced settling and dewatering by conditioning was evaluated in order to reduce the treatment footprint (or increase treatment capacity). Conventional wastewater conditioners, such as commercially available lime and polymers, are expensive, and commonly rely on complex supply chains for use in low-income countries. Therefore, the treatment performance of five conditioners which could be produced locally was evaluated: Moringa oleifera seeds and press cake, Jatropha curcas seeds, Jatropha Calotropis leaves and chitosan. M. oleifera seeds and press cake, and chitosan improved settling and dewatering and had a similar performance compared to lime and polymers. Optimal dosages were 400-500 kg M. oleifera/t TS, 300-800 kg lime/t TS and 25-50 kg polymer solution/t TS. In comparison, chitosan required 1.5-3.75 kg/t TS. These dosages are comparable to those recommended for wastewater (sludge). The results indicate that conditioning of FS can reduce total suspended solids (TSS) in the effluent of settling-thickening tanks by 22-81% and reduce dewatering time with drying beds by 59-97%. This means that the area of drying beds could be reduced by 59-97% with end-use as soil conditioner, or 9-26% as solid fuel. Least expensive options and availability will depend on the local context. In Dakar, Senegal, chitosan produced from shrimp waste appears to be most promising.

Effects of different sludge disintegration methods on sludge moisture distribution and dewatering performance.

Science.gov (United States)

Jin, Lingyun; Zhang, Guangming; Zheng, Xiang

2015-02-01

A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge disintegration can destroy the sludge structure and cell wall, so as change the sludge floc structure and moisture distribution, thus affecting the dewatering performance of sludge. In this article, the disintegration methods were ultrasound treatment, K2FeO4 oxidation and KMnO4 oxidation. The degree of disintegration (DDCOD), sludge moisture distribution and the final water content of sludge cake after centrifuging were measured. Results showed that three disintegration methods were all effective, and K2FeO4 oxidation was more efficient than KMnO4 oxidation. The content of free water increased obviously with K2FeO4 and KMnO4 oxidations, while it decreased with ultrasound treatment. The changes of free water and interstitial water were in the opposite trend. The content of bounding water decreased with K2FeO4 oxidation, and increased slightly with KMnO4 oxidation, while it increased obviously with ultrasound treatment. The water content of sludge cake after centrifuging decreased with K2FeO4 oxidation, and did not changed with KMnO4 oxidation, but increased obviously with ultrasound treatment. In summary, ultrasound treatment deteriorated the sludge dewaterability, while K2FeO4 and KMnO4 oxidation improved the sludge dewaterability. Copyright © 2014. Published by Elsevier B.V.

Full-scale performance of selected starch-based biodegradable polymers in sludge dewatering and recommendation for applications.

Science.gov (United States)

Zhou, Kuangxin; Stüber, Johan; Schubert, Rabea-Luisa; Kabbe, Christian; Barjenbruch, Matthias

2018-01-01

Agricultural reuse of dewatered sludge is a valid route for sludge valorization for small and mid-size wastewater treatment plants (WWTPs) due to the direct utilization of nutrients. A more stringent of German fertilizer ordinance requires the degradation of 20% of the synthetic additives like polymeric substance within two years, which came into force on 1 January 2017. This study assessed the use of starch-based polymers for full-scale dewatering of municipal sewage sludge. The laboratory-scale and pilot-scale trials paved the way for full-scale trials at three WWTPs in Germany. The general feasibility of applying starch-based 'green' polymers in full-scale centrifugation was demonstrated. Depending on the sludge type and the process used, the substitution potential was up to 70%. Substitution of 20-30% of the polyacrylamide (PAM)-based polymer was shown to achieve similar total solids (TS) of the dewatered sludge. Optimization of operational parameters as well as machinery set up in WWTPs is recommended in order to improve the shear stability force of sludge flocs and to achieve higher substitution potential. This study suggests that starch-based biodegradable polymers have great potential as alternatives to synthetic polymers in sludge dewatering.

Electroosmotic dewatering of chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge

DEFF Research Database (Denmark)

Hansen, H.K.; Christensen, Iben Vernegren; Ottosen, Lisbeth M.

2003-01-01

. Casagrande's coefficients were determined for the four materials at different water contents. The experiments in this work showed that chalk could be dewatered from 40% to 79% DM (dry matter), fly ash from 75 to 82% DM, iron hydroxide sludge from 2.7 to 19% DM and biomass from 3 to 33% DM by electroosmosis....... The process was not optimised indicating that higher dry matter contents could be achieved by electroosmosis. It was possible to relate Casagrande's coefficient directly to the electroosmotic coefficient obtained by dewatering experiments....

Model test on partial expansion in stratified subsidence during foundation pit dewatering

Science.gov (United States)

Wang, Jianxiu; Deng, Yansheng; Ma, Ruiqiang; Liu, Xiaotian; Guo, Qingfeng; Liu, Shaoli; Shao, Yule; Wu, Linbo; Zhou, Jie; Yang, Tianliang; Wang, Hanmei; Huang, Xinlei

2018-02-01

Partial expansion was observed in stratified subsidence during foundation pit dewatering. However, the phenomenon was suspected to be an error because the compression of layers is known to occur when subsidence occurs. A slice of the subsidence cone induced by drawdown was selected as the prototype. Model tests were performed to investigate the phenomenon. The underlying confined aquifer was generated as a movable rigid plate with a hinge at one end. The overlying layers were simulated with remolded materials collected from a construction site. Model tests performed under the conceptual model indicated that partial expansion occurred in stratified settlements under coordination deformation and consolidation conditions. During foundation pit dewatering, rapid drawdown resulted in rapid subsidence in the dewatered confined aquifer. The rapidly subsiding confined aquifer top was the bottom deformation boundary of the overlying layers. Non-coordination deformation was observed at the top and bottom of the subsiding overlying layers. The subsidence of overlying layers was larger at the bottom than at the top. The layers expanded and became thicker. The phenomenon was verified using numerical simulation method based on finite difference method. Compared with numerical simulation results, the boundary effect of the physical tests was obvious in the observation point close to the movable endpoint. The tensile stress of the overlying soil layers induced by the underlying settlement of dewatered confined aquifer contributed to the expansion phenomenon. The partial expansion of overlying soil layers was defined as inversed rebound. The inversed rebound was induced by inversed coordination deformation. Compression was induced by the consolidation in the overlying soil layers because of drainage. Partial expansion occurred when the expansion exceeded the compression. Considering the inversed rebound, traditional layer-wise summation method for calculating subsidence should be

Consolidation theory and its applicability to the dewatering and covering of uranium-mill tailings

International Nuclear Information System (INIS)

Gates, T.E.

1982-11-01

This report is a review and evaluation of soil consolidation theories applicable for evaluating settlement during dewatering and subsequent covering of uranium-mill tailings. Such theories may be used to predict both consolidation and water flow related effects in uranium-mill tailings during drainage, following sluicing into burial pits. A consolidation theory to be useful must consider the effect of time-dependent loads, nonhomogeneous soil mass, nonlinear variation of soil properties with the stress-state parameters, large strain, and saturated and unsaturated flow. Constitutive relations linking the stress-deformation-state variables with void ratio should be adopted for predicting both consolidation and fluid-flow interaction in unsaturated uranium-mill tailings

Cleaning and dewatering fine coal

Science.gov (United States)

Yoon, Roe-Hoan; Eraydin, Mert K.; Freeland, Chad

2017-10-17

Fine coal is cleaned of its mineral matter impurities and dewatered by mixing the aqueous slurry containing both with a hydrophobic liquid, subjecting the mixture to a phase separation. The resulting hydrophobic liquid phase contains coal particles free of surface moisture and droplets of water stabilized by coal particles, while the aqueous phase contains the mineral matter. By separating the entrained water droplets from the coal particles mechanically, a clean coal product of substantially reduced mineral matter and moisture contents is obtained. The spent hydrophobic liquid is separated from the clean coal product and recycled. The process can also be used to separate one type of hydrophilic particles from another by selectively hydrophobizing one.

Field experiment and numerical simulation of coupling non-Darcy flow caused by curtain and pumping well in foundation pit dewatering

Science.gov (United States)

Wang, Jianxiu; Liu, Xiaotian; Wu, Yuanbin; Liu, Shaoli; Wu, Lingao; Lou, Rongxiang; Lu, Jiansheng; Yin, Yao

2017-06-01

High-velocity non-Darcy flow produced larger drawdown than Darcy flow under the same pumping rate. When the non-Darcy flow caused by curtain met non-Darcy flow caused by pumping wells, superposition and amplification effect occurred in the coupling area, the non-Darcy flow was defined as coupling non-Darcy flow. The coupling non-Darcy flow can be produced and controlled using different combination of curtain and pumping wells in foundation pit dewatering to obtain the maximum drawdown using the minimum pumping rate. The Qianjiang Century City Station foundation pit of Hangzhou subway, China, was selected as background. Field experiments were performed to observe the coupling non-Darcy flow in round gravel. A generalized conceptual model was established to study the coupling effect under different combination of curtain and pumping wells. Numerical simulations of the coupling non-Darcy flow in foundation pit dewatering were carried out based on the Forchheimer equation. The non-Darcy flow area and flow velocity were influenced by the coupling effect. Short filter tube, large pumping rate, small horizontal distance between filter tube and diaphragm wall, and small vertical distance between the filter tube and confined aquifer roof effectively strengthened the coupling effect and obtained a large drawdown. The pumping wells installed close to a curtain was an intentional choice designed to create coupling non-Darcy flow and obtain the maximize drawdown. It can be used in the dewatering of a long and narrow foundation pit, such as a subway foundation pit.

Acceleration of organic removal and electricity generation from dewatered oily sludge in a bioelectrochemical system by rhamnolipid addition.

Science.gov (United States)

Zhang, Yunshu; Zhao, Qingliang; Jiang, Junqiu; Wang, Kun; Wei, Liangliang; Ding, Jing; Yu, Hang

2017-11-01

Conversion of biomass energy of dewatered oily sludge to electricity is the rate-limiting process in bioelectrochemical system (BES). In this study, 2mgg -1 rhamnolipids were added to dewatered oily sludge, resulting in a significant enhancement in maximum power density from 3.84±0.37 to 8.63±0.81Wm -3 , together with an increase in total organic carbon (TOC) and total petroleum hydrocarbon (TPH) removal from 24.52±4.30 to 36.15±2.79mgg -1 and 29.51±3.30 to 39.80±2.47mgg -1 , respectively. Rhamnolipids can also enhance the solubilization and promote the hydrolysis of dewatered oily sludge with increases in SOCD from 14.93±2.44 to 18.40±0.08mgg -1 and VFAs from 1.02±0.07 to 1.39±0.12mgg -1 . Furthermore, bacteria related to substrate degradation were predominant in dewatered oily sludge, and bacteria related to the sulfate/sulfide cycle were significantly enriched by rhamnolipid addition. Copyright © 2017 Elsevier Ltd. All rights reserved.

Efficient Calculation of Dewatered and Entrapped Areas Using Hydrodynamic Modeling and GIS

International Nuclear Information System (INIS)

Richmond, Marshall C.; Perkins, William A.

2009-01-01

River waters downstream of a hydroelectric project are often subject to rapidly changing discharge. Abrupt decreases in discharge can quickly dewater and expose some areas and isolate other areas from the main river channel, potentially stranding or entrapping fish, which often results in mortality. A methodology is described to estimate the areas dewatered or entrapped by a specific reduction in upstream discharge. A one-dimensional hydrodynamic model was used to simulate steady flows. Using flow simulation results from the model and a geographic information system (GIS), estimates of dewatered and entrapped areas were made for a wide discharge range. The methodology was applied to the Hanford Reach of the Columbia River in central Washington State. Results showed that a 280 m 3 /s discharge reduction affected the most area at discharges less than 3400 m 3 /s. At flows above 3400 m 3 /s, the affected area by a 280 m 3 /s discharge reduction (about 25 ha) was relatively constant. A 280 m 3 /s discharge reduction at lower flows affected about twice as much area. The methodology and resulting area estimates were, at the time of writing, being used to identify discharge regimes, and associated water surface elevations, that might be expected to minimize adverse impacts on juvenile fall chinook salmon (Oncorhynchus tshawytscha) that rear in the shallow near-shore areas in the Hanford Reach

A Case Study on Stratified Settlement and Rebound Characteristics due to Dewatering in Shanghai Subway Station

OpenAIRE

Wang, Jianxiu; Huang, Tianrong; Sui, Dongchang

2013-01-01

Based on the Yishan Metro Station Project of Shanghai Metro Line number 9, a centrifugal model test was conducted to investigate the behavior of stratified settlement and rebound (SSR) of Shanghai soft clay caused by dewatering in deep subway station pit. The soil model was composed of three layers, and the dewatering process was simulated by self-invention of decompressing devise. The results indicate that SSR occurs when the decompression was carried out, and only negative rebound was found...

Electroosmotic dewatering of chalk sludge, iron hydroxide sludge, wet fly ash and biomass

Energy Technology Data Exchange (ETDEWEB)

Hansen, H.K.; Kristensen, I.V.; Ottosen, L.M.; Villumsen, A. [Dept. of Geology and Geotechnical Engineering, The Technical Univ. of Denmark, Lyngby (Denmark)

2001-07-01

Electroosmotic dewatering has been tested in laboratory cells for 4 different porous materials: chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge from enzyme production. In all cases it was possible to remove water when passing electric DC current through the material. Casagrande's coefficients for the three materials where determined at different water contents. In the electroosmotic experiments shown in this work chalk can be dewatered from 40% to 79% DM (dry matter), fly ash from 75 to 82% DM, iron hydroxide sludge from 2.7 to 19% DM and biomass from 3 to 33% DM. The process was not optimised indicating that higher dry matter contents could be achieved. (orig.)

Prediction and verification of centrifugal dewatering of P. pastoris fermentation cultures using an ultra scale-down approach.

Science.gov (United States)

Lopes, A G; Keshavarz-Moore, E

2012-08-01

Recent years have seen a dramatic rise in fermentation broth cell densities and a shift to extracellular product expression in microbial cells. As a result, dewatering characteristics during cell separation is of importance, as any liquor trapped in the sediment results in loss of product, and thus a decrease in product recovery. In this study, an ultra scale-down (USD) approach was developed to enable the rapid assessment of dewatering performance of pilot-scale centrifuges with intermittent solids discharge. The results were then verified at scale for two types of pilot-scale centrifuges: a tubular bowl equipment and a disk-stack centrifuge. Initial experiments showed that employing a laboratory-scale centrifugal mimic based on using a comparable feed concentration to that of the pilot-scale centrifuge, does not successfully predict the dewatering performance at scale (P-value centrifuge. Initial experiments used Baker's yeast feed suspensions followed by fresh Pichia pastoris fermentation cultures. This work presents a simple and novel USD approach to predict dewatering levels in two types of pilot-scale centrifuges using small quantities of feedstock (centrifuge needs to be operated, reducing the need for repeated pilot-scale runs during early stages of process development. Copyright © 2012 Wiley Periodicals, Inc.

Sludge dewatering on filters aiming the utilization as fuel; Desaguamento de lodos em filtro visando aproveitamento como combustivel

Energy Technology Data Exchange (ETDEWEB)

Paschoalim, Luis Gustavo; Neves, Jose Mangolini

1993-12-31

This work presents modern methodologies for sludge dewatering and alternatives for environmental disposal of the so obtained cakes. Among the possible alternatives, special emphasis is given to the characterization and study of the variables which determine the behaviour of dewatering operation of sludges form pulp and paper industries. Results are presents for bench scale tests and pilot plant tests 28 refs., 9 figs., 7 tabs.

Sludge dewatering on filters aiming the utilization as fuel; Desaguamento de lodos em filtro visando aproveitamento como combustivel

Energy Technology Data Exchange (ETDEWEB)

Paschoalim, Luis Gustavo; Neves, Jose Mangolini

1992-12-31

This work presents modern methodologies for sludge dewatering and alternatives for environmental disposal of the so obtained cakes. Among the possible alternatives, special emphasis is given to the characterization and study of the variables which determine the behaviour of dewatering operation of sludges form pulp and paper industries. Results are presents for bench scale tests and pilot plant tests 28 refs., 9 figs., 7 tabs.

Dewatering and low-temperature pyrolysis of oily sludge in the presence of various agricultural biomasses.

Science.gov (United States)

Zhao, Song; Zhou, Xiehong; Wang, Chuanyi; Jia, Hanzhong

2017-08-24

Pyrolysis is potentially an effective treatment of waste oil residues for recovery of petroleum hydrocarbons, and the addition of biomass is expected to improve its dewatering and pyrolysis behavior. In this study, the dewatering and low-temperature co-pyrolysis of oil-containing sludge in the presence of various agricultural biomasses, such as rice husk, walnut shell, sawdust, and apricot shell, were explored. As a result, the water content gradually decreases with the increase of biomass addition within 0-1.0 wt % in original oily sludge. Comparatively, the dewatering efficiency of sludge in the presence of four types of biomasses follows the order of apricot shell > walnut shell > rice husk > sawdust. On the other hand, rice husk and sawdust are relatively more efficient in the recovery of petroleum hydrocarbons compared with walnut shell and apricot shell. The recovery efficiency generally increased with the increase in the biomass content in the range of 0-0.2 wt %, then exhibited a gradually decreasing trend with the increase in the biomass content from 0.2 to 1.0 wt %. The results suggest that optimum amount of biomass plays an important role in the recovery efficiency. In addition, the addition of biomass (such as rice husk) also promotes the formation of C x H y and CO, increasing the calorific value of pyrolysis residue, and controlled the pollution components of the exhaust gas discharged from residue incineration. The present work implies that biomass as addictive holds great potential in the industrial dewatering and pyrolysis of oil-containing sludge.

Optimal dewatering schemes in the foundation design of an electronuclear plant

International Nuclear Information System (INIS)

Galeati, G.; Gambolati, G.

1988-01-01

A three-dimensional finite element model combined with an optimization approach based on linear mixed integer programming is developed and applied to assist in the design of the dewatering system for the electronuclear plant to be built by the Italian Electric Agency (ENEL) in Trino Vercellese, northwestern Italy. The foundations site is encompassed by a 25- to 35-m deep plastic wall with the purpose of protecting the unconfined aquifer from the significant water table lowering required by the construction project. To reduce further the propagation of the depression cone a large amount of the water pumped out is reinjected through ad hoc recharge ditches. The finite element optimization model includes both the natural and the artificial constraints and provides several optimal withdrawal strategies for the dewatering system design concerning the distribution of the abstraction wells and the corresponding pumping rates. Physical and economical objective functions are explored and the related solutions are discussed

Enhancing the dewatering properties of sludge through aimed building-up of floc structures on the basis of detailed morphological analyses; Verbesserung der Entwaesserungseigenschaften von Schlaemmen durch den gezielten Aufbau von Flockenstrukturen auf der Basis detaillierter morphologischer Analysen

Energy Technology Data Exchange (ETDEWEB)

Nagel, M.; Ay, P. [Brandenburgische Technische Univ. Cottbus (Germany). Lehrstuhl Aufbereitungstechnik

1999-07-01

Aimed building-up of aggregates as they originate in flocculation processes, for instance in sewage and sludge treatment, have especially lately been meeting with increasing resonance: they permit to influence, inter alia, important properties (e.g., the dewatering properties) of such systems. As conventional mathematical methods for the characterization of flocs - as a basis for process optimization - are inadequate or flawed, a concept for the effective characterization of the inner getup of such structures needs to be sought. One approach is cluster analysis, which is demonstrated and discussed in the present paper by means of the evaluation of sectional views of floc structures. (orig.) [German] Der gezielte Aufbau von Aggregaten, wie sie bei Flockungsprozessen z.B. in der Abwasser- und Schlammbehandlung entstehen, findet besonders in juengerer Zeit zunehmend Beachtung, da sich damit unter anderem wichtige Eigenschaften (z.B. die Entwaesserungseigenschaften) dieser Systeme beeinflussen lassen. Da herkoemmliche mathematische Methoden zur Charakterisierung von Flocken - als Basis fuer eine Prozessoptimierung - nur unzureichend bzw. fehlerbehaftet sind, ergibt sich daraus die Notwendigkeit, nach einem Konzept zur effektiven Charakterisierung des inneren Aufbaus solcher Strukturen zu suchen. Ein Ansatz ist die Clusteranalyse, die im Beitrag durch die Auswertung von Schnittbildern von Flockenstrukturen vorgestellt und diskutiert wird. (orig.)

Feasibility study of green wastes composting with digested and dewatering sludge from municipal wastewater treatment plant in Iran

Directory of Open Access Journals (Sweden)

Neamat Jaafarzadeh Haghighi Fard

2015-09-01

Full Text Available Background: Composting as a waste management technology is becoming more widespread. The purpose of this study was to assess the feasibility and to find the most effective composting process for the ratio of green waste, digested and dewatered sludge from Chonibieh wastewater treatment plant in the west region of Ahvaz. Methods: The composting time was 23 days and the evaluated parameters in this period of the study were organic carbon, total nitrogen, phosphorus, carbon to nitrogen ratio (C/N, moisture content and pH. The C/N ratio was maintained at 30 with weight:weight ratio of 1:1, 1:2, 1:3 (digested and dewatered sludge to green waste. Results: It was observed that vessel R3 produced higher quality of compost with final total nitrogen (1.28%, final total phosphorus (0.71%, final total organic carbon (TOC (25.78% and C/N (20.65% within the 23 days of composting. While vessel R1 produced higher final total nitrogen and total phosphorus with lower amount of total coliform indicating suitable quality of composting. Therefore, the results showed that the characteristics of dewatered sludge mixed with green waste proportion of green waste significantly influenced the compost quality and process dynamics. The results also showed that the quality of final products in all the conditions was in agreement with Global Organic Textile Standard (GOTS and World Health Organization (WHO guidelines. However, the moisture content ratios were lower than the mentioned guidelines. With regards to microbial quality, all three ratios were in agreement with US Environmental Protection Agency (EPA and Iranian guidelines. Conclusion: It is suggested that the final product of composting can be safely used in farmland and green space.

Vibrating membrane filtration as improved technology for microalgae dewatering

OpenAIRE

Nurra, C.; Clavero, E.; Salvadó, J.; Torras, C.

2014-01-01

10.1016/j.biortech.2014.01.115 The effect of shear-enhanced filtration by vibratory process in microalgae dewatering is presented in this paper. The aim of this research was to investigate the technical performance and improvement of vibrating membrane filtration compared with conventional tangential cross-flow filtration in microalgae concentration. An industrial-scale available commercial set-up was used. Several membrane materials as polyethersulfone, polyacrylonitrile, etc., and mean ...

46 CFR 28.815 - Bilge pumps, bilge piping, and dewatering systems.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Bilge pumps, bilge piping, and dewatering systems. 28... REQUIREMENTS FOR COMMERCIAL FISHING INDUSTRY VESSELS Aleutian Trade Act Vessels § 28.815 Bilge pumps, bilge... fixed, self priming, powered, bilge pump, having a minimum capacity rating of 50 gallons per minute...

Physical, chemical and dewatering characteristics of Ba/RaSO4 sludges from uranium milling

International Nuclear Information System (INIS)

Skeaff, J.M.; Campbell, H.W.

1980-01-01

There is concern that long-term environmental pollution caused by radionuclide-bearing acid drainage could occur upon the abandonment of uranium tailings areas. One source of dissolved radionuclides could be the Ba/RaSO 4 sludges formed in most tailings ponds. Prior to discharge to open watercourses, uranium tailings decants are usually treated with barium chloride to coprecipitate dissolved radium. The resulting sludge is allowed to settle in ponds, the size and retention time of which will depend on the mine site. It may be necessary for environmental reasons to remove these sludges for permanent disposal. CANMET has awarded a contract to Kilborn Ltd. of Toronto to study methods for the recovery and dewatering of these sludges. To provide data for the Kilborn contract on the physical, chemical and dewatering of Ba/RaSO 4 sludges presently being produced at uranium mine/mill sites, samples were taken from the operational settling ponds at Rio Algom Mines Ltd., Elliot Lake. Dewatering characterization has also been conducted on two pilot plant facility sludges, one produced at the Wastewater Technology Centre's pilot plant at Rio Algom Mines, and the other from the pilot scale settling ponds designed by James F. MacLaren Ltd. for Rio Algom. The chemical and radionuclide analyses for the CANMET sludge are also reported

Isolation and Characterization of Polyacrylamide-Degrading Bacteria from Dewatered Sludge

Directory of Open Access Journals (Sweden)

Feng Yu

2015-04-01

Full Text Available Polyacrylamide (PAM is a water-soluble polymer that is widely used as a flocculant in sewage treatment. The accumulation of PAM affects the formation of dewatered sludge and potentially produces hazardous monomers. In the present study, the bacterial strain HI47 was isolated from dewatered sludge. This strain could metabolize PAM as its sole nutrient source and was subsequently identified as Pseudomonas putida. The efficiency of PAM degradation was 31.1% in 7 days and exceeded 45% under optimum culture condition (pH 7.2, 39 °C and 100 rpm. The addition of yeast extract and glucose improved the bacterial growth and PAM degradation. The degraded PAM samples were analyzed by gel-filtration chromatography, Fourier transform infrared and high-performance liquid chromatography. The results showed that high-molecular-weight PAM was partly cleaved to small molecular oligomer derivatives and part of the amide groups of PAM had been converted to carboxyl groups. The biodegradation did not accumulate acrylamide monomers. Based on the SDS-PAGE and N-terminal sequencing results, the PAM amide groups were converted into carboxyl groups by a PAM-induced extracellular enzyme from the aliphatic amidase family.

A novel acrylamide-free flocculant and its application for sludge dewatering.

Science.gov (United States)

Lu, Lianghua; Pan, Zhida; Hao, Nan; Peng, Wenqing

2014-06-15

In the present research, copolymers of methyl acrylate (MA) with anionic or cationic monomers were synthesized via emulsion polymerization, and used as sludge dewatering aids in wastewater treatment. The copolymerization of different stoichiometry of two monomers afforded a variety of water soluble copolymers with charge densities ranging from 40% to 80%, which align with the charge density of current flocculant products. These copolymers resemble current commercial products, but provide a greener solution by eliminating acrylamide monomer, which is a suspected carcinogen. High molecular weight copolymers were achieved by applying powder-like synthesis process with intrinsic viscosity of final products as high as 12.98 dl/g for anionic flocculant and 10.74 dl/g for cationic flocculant. The copolymers of methyl acrylate and [2-(Acryloyloxy)ethyl]trimethylammonium chloride (AETAC) with 55% charge density exhibited comparable performance in clay settling test, real water jar test, and sludge dewatering, when compared to AM-based commercial product in the real wastewater treatment application. Copyright © 2014 Elsevier Ltd. All rights reserved.

An environmental isotope study of a major dewatering operation at Sishen mine, northern Cape Province

International Nuclear Information System (INIS)

Verhagen, B.T.; Smith, P.E.; Dziembowski, Z.; Oosthuizen, J.H.

1978-01-01

Geohydrological studies using environmental isotopes of the Sishen iron ore mine were started after major rainfalls in 1973/74 produced flooding of the open cast workings. The mine is underlain by dolomite which has been extensively karstified and geohydrologically compartmentalized by several dykes. Major dewatering takes place in a pit called Hill 2 by pumping an array of large diameter boreholes at a combined rate of 2000 m 3 h -1 . The probable recharge areas (dolomites, superficial Kalahari Beds) were isotopically surveyed to assess their relative importance to the dewatering problem. Several major pumping outlets at the mine were regularly sampled for isotopic and chemical analysis and from the data a preliminary mixing model is proposed. The data also show that with the total pumped volume up to March 1978, no very recent (i.e. post bomb) water has reached the dewatering points. On this basis a minimum storage of 0.75 x 10 8 m 3 is derived compared to a classical calculation of 10 8 m 3 for the compartment. Isotopic composition and response differ for waters on either side of a dyke crossing the mining area, corroborating classical evidence suggesting that the dyke acts as an aquiclude. (orig.) [de

An environmental isotope study of a major dewatering operation at Sishen mine, northern Cape Province

International Nuclear Information System (INIS)

Verhagen, B.Th.; Smith, P.E.; Oosthuizen, J.H.

1979-01-01

Geohydrological studies using environmental isotopes of the Sishen iron ore mine were started after major rainfalls in 1973/74 produced flooding of the open cast workings. The mine is underlain by dolomite which has been extensively karstified and geohydrologically compartmentalized by several dykes. Major dewatering takes place in a pit called Hill 2 by pumping an array of large-diameter boreholes at a combined rate of 2000m 3 h -1 . The probable recharge areas (dolomites, superficial Kalahari Beds) were isotopically surveyed to assess their relative importance to the dewatering problem. Several major pumping outlets at the mine were regularly sampled for isotopic and chemical analysis and from the data a preliminary mixing model is proposed. The data also show that, with the total pumped volume up to March 1978, no very recent (i.e. post-bomb) water has reached the dewatering points. On this basis a minimum storage of 0.75x10 8 m 3 is derived compared with a classical calculation of 10 8 m 3 for the compartment. Isotopic composition and response differ for waters on either side of a dyke crossing the mining area, corroborating classical evidence suggesting that the dyke acts as an aquiclude. (author)

Device for dewatering of raw biomass. Anordning foer avvattning och uppluckring av raa biomassa

Energy Technology Data Exchange (ETDEWEB)

Kubat, J; Aabom, J J.V.; Klason, T C.F.; Bultzingsloewen, F von

1993-09-27

This invention concerns a device for loosening of raw biomass through roll dewatering. It is primarily applicable for comminuted and milled raw wood. The invention is of special interest for the production of pulverized wood fuel

A comparison of the economic benefits of centralized and distributed model predictive control strategies for optimal and sub-optimal mine dewatering system designs

International Nuclear Information System (INIS)

Romero, Alberto; Millar, Dean; Carvalho, Monica; Maestre, José M.; Camacho, Eduardo F.

2015-01-01

Mine dewatering can represent up to 5% of the total energy demand of a mine, and is one of the mine systems that aim to guarantee safe operating conditions. As mines go deeper, dewatering pumping heads become bigger, potentially involving several lift stages. Greater depth does not only mean greater dewatering cost, but more complex systems that require more sophisticated control systems, especially if mine operators wish to gain benefits from demand response incentives that are becoming a routine part of electricity tariffs. This work explores a two stage economic optimization procedure of an underground mine dewatering system, comprising two lifting stages, each one including a pump station and a water reservoir. First, the system design is optimized considering hourly characteristic dewatering demands for twelve days, one day representing each month of the year to account for seasonal dewatering demand variations. This design optimization minimizes the annualized cost of the system, and therefore includes the investment costs in underground reservoirs. Reservoir size, as well as an hourly pumping operation plan are calculated for specific operating environments, defined by characteristic hourly electricity prices and water inflows (seepage and water use from production activities), at best known through historical observations for the previous year. There is no guarantee that the system design will remain optimal when it faces the water inflows and market determined electricity prices of the year ahead, or subsequent years ahead, because these remain unknown at design time. Consequently, the dewatering optimized system design is adopted subsequently as part of a Model Predictive Control (MPC) strategy that adaptively maintains optimality during the operations phase. Centralized, distributed and non-centralized MPC strategies are explored. Results show that the system can be reliably controlled using any of these control strategies proposed. Under the operating

Effect of TiO2 nanoparticles on UASB biomass activity and dewatered sludge.

Science.gov (United States)

Yadav, Tushar; Mungray, Alka A; Mungray, Arvind K

2017-02-01

The accumulation of the nanowastes in the wastewater treatment plants has raised several concerns; therefore, it is an utmost priority to study the nanoparticle (NP) toxicity in such systems. In this work, the effect of TiO 2 NPs on up-flow anaerobic sludge blanket (UASB) microflora and their photocatalytic effect on dewatered sludge were studied. We observed 99.98% removal of TiO 2 NPs by sludge biomass within 24 h, though negligible toxicity was found up to 100 mg/L TiO 2 concentration on extracellular polymeric substances (EPS), volatile fatty acid and biogas generation. The low toxicity corresponds to the agglomeration of TiO 2 NPs in UASB sludge. Alterations in dewatered sludge biochemical composition and increase in cell damage were observed upon exposure to sunlight as evidenced by FTIR and fluorescent microscopy, respectively. Results suggest the negligible toxicity of TiO 2 NPs on UASB biomass activity; however, once exposed to open environment and sunlight, they may exert detrimental effects.

Effect of biodegradation on the consolidation properties of a dewatered municipal sewage sludge.

Science.gov (United States)

O'Kelly, Brendan C

2008-01-01

The effect of biodegradation on the consolidation characteristics of an anaerobically digested, dewatered municipal sewage sludge was studied. Maintained-load oedometer consolidation tests that included measurement of the pore fluid pressure response were conducted on moderately degraded sludge material and saturated bulk samples that had been stored under static conditions and allowed to anaerobically biodegrade further (simulating what would happen in an actual sewage sludge monofill or lagoon condition). Strongly degraded sludge material was produced after a storage period of 13 years at ambient temperatures of 5-15 degrees C, with the total volatile solids reducing from initially 70% to 55%. The sludge materials were highly compressible, although impermeable for practical purposes. Primary consolidation generally occurred very slowly, which was attributed to the microstructure of the solid phase, the composition and viscosity of the pore fluid, ongoing biodegradation and the high organic contents. The coefficient of primary consolidation values decreased from initially about 0.35m2/yr to 0.003-0.03m2/yr with increasing effective stress (sigmav'=3-100kPa). Initially, the strongly degraded sludge material was slightly more permeable, although both the moderately and strongly degraded materials became impermeable for practical purposes (k=10(-9)-10(-12)m/s) below about 650% and 450% water contents, respectively. Secondary compression became more dominant with increasing effective stress with a mean secondary compression index (Calphae) value of 0.9 measured for both the moderately and strongly degraded materials.

Environmental control of drilling mud discharge through dewatering in cold weather climates: effect of ambient temperature

Energy Technology Data Exchange (ETDEWEB)

Wojtanowicz, A. K. [Louisiana State Univ., Baton Rouge, LA (United States); Ye, Y. [Jianghan Petroleum Institute, Beijing, (China)

1998-05-01

Results of an experimental study of the effects of drilling mud temperature upon dewatering performance at various temperatures were presented. Three temperature ranges (from flowline temperature to room temperature, from room temperature to freezing point, and freeze/thaw, i.e. from -20 degrees C to 12 degrees C) were considered. Both unweighted and weighted fresh water muds and weighted salt water mud were tested using a sealed laboratory batch reactor, to prevent rapid vaporization of separated water at temperatures above 60 degrees C. Deep freezing was achieved by using ice or ice-salt baths. Net water removal was measured with a bench-top plate press under constant expression pressure of 270 kPa. Results showed that the freeze/thaw treatment process proved to be very effective, enhancing water removal by 34 to 39 per cent, and reducing waste mud volume by 64 to 72 per cent. No advantage to dewatering hot drilling mud from active systems was observed at temperatures above 21 degrees C. It was suggested that at temperatures under 21 degrees C, the waste drilling mud diverted from an active system should be dewatered when its temperature is still over 40 degrees C. to reduce the amount of chemicals needed for separation enhancement. 14 refs., 4 tabs., 4 figs.

Hydrothermal treatment coupled with mechanical expression at increased temperature for excess sludge dewatering: the dewatering performance and the characteristics of products.

Science.gov (United States)

Wang, Liping; Li, Aimin

2015-01-01

Hydrothermal treatment coupled with mechanical expression at increased temperature in two separate cells respectively is effective for the dewatering of excess sludge with low energy consumption. The objectives of this study were to evaluate the dewatering performance and the characteristics of obtained products (hydrothermal sludge, hydrochar and filtrate). The results showed that harsher hydrothermal treatment (temperature from 120 to 210 °C and residence time from 10 to 90 min) led to greater water removal (from 7.44 to 96.64% reduction of total water) and mechanical pressure became less significant as it increased. The whole expression stage was completely described by the modified Terzaghi-Voigt rheological model. The role of tertiary consolidation stage in the water removal was reduced with hydrothermal treatment being stronger. The hydrothermal treatment is mainly a devolatilization process. The observed changes in H/C and O/C for hydrothermal sludge suggested dehydration was the major reaction mechanism and decarboxylation only occurred significantly at higher temperature. The higher heating value correlated well with carbon content of sludge, which was increased by 4.8% for hydrothermal sludge at 210 °C for 60 min and significantly decreased by 15.4% for hydrochar after 6.0 MPa for 20 min. The solubilization and decomposition of proteins, polysaccharides and DNA were determined to be temperature and residence time dependent. The improvement of dewaterability was closely correlated to the variation of these biopolymers. The filtrates collected above 150 °C were found to be acidic. The increase of humic substances and the melanoidins formed by Maillard reaction were largely responsible for the filtrate color.

Chitosan use in chemical conditioning for dewatering municipal-activated sludge.

Science.gov (United States)

Zemmouri, H; Mameri, N; Lounici, H

2015-01-01

This work aims to evaluate the potential use of chitosan as an eco-friendly flocculant in chemical conditioning of municipal-activated sludge. Chitosan effectiveness was compared with synthetic cationic polyelectrolyte Sedipur CF802 (Sed CF802) and ferric chloride (FeCl₃). In this context, raw sludge samples from Beni-Messous wastewater treatment plant (WWTP) were tested. The classic jar test method was used to condition sludge samples. Capillary suction time (CST), specific resistance to filtration (SRF), cakes dry solid content and filtrate turbidity were analyzed to determine filterability, dewatering capacity of conditioned sludge and the optimum dose of each conditioner. Data exhibit that chitosan, FeCl₃and Sed CF802 improve sludge dewatering. Optimum dosages of chitosan, Sed CF802 and FeCl₃allowing CST values of 6, 5 and 9 s, were found, respectively, between 2-3, 1.5-3 and 6 kg/t ds. Both polymers have shown faster water removal with more permeable sludge. SRF values were 0.634 × 10¹², 0.932 × 10¹² and 2 × 10¹² m/kg for Sed CF802, chitosan and FeCl₃respectively. A reduction of 94.68 and 87.85% of the filtrate turbidity was obtained with optimal dosage of chitosan and Sed CF802, respectively. In contrast, 54.18% of turbidity abatement has been obtained using optimal dosage of FeCl₃.

Network model for fine coal dewatering. Part I. The model

Energy Technology Data Exchange (ETDEWEB)

Qamar, I.; Tierney, J.W.; Chiang, S.H.

1985-08-01

There is a body of well established research in filtration and related subjects, but much of it has been empirical - based on correlations from experimental data. This approach has the disadvantage that it lacks generality, and it is difficult to predict the behavior of new or different systems. A more general method for studying dewatering is needed-one which will include the microscopic characteristics of the filter cake, which, like other porous media, contains a complicated network of interconnected pores through which the fluid must flow. These pores play an important role in dewatering because they give rise to capillary forces when one fluid is displacing another. In this report, we describe a network model which we believe satisfies these requirements. In the main body of this report, the model is described in detail. Background information is given where appropriate, and a brief description is given of the experimental work being done in our laboratories to verify the model. A detailed description of the experimental procedures and results is given in other DOE reports. The computer programs which are needed to solve the model are described in detail in the Appendices and are accompanied by flow charts, sample problems, and sample outputs. Sufficient detail is given in order to use the model programs on other computer systems. 32 refs., 7 figs., 5 tabs.

Procedure of dewatering by pressing of biomass pulp, especially a peat cake. Saett att genom pressning avvattna en kaka av biomassa, foeretraedesvis en torvkaka

Energy Technology Data Exchange (ETDEWEB)

Eriksson, S

1988-05-24

The pulp is dewatered by pressing above 90 degrees C, the pulp water being displaced by warmer water under successively increased pressure. A device designed like a closed washing press is used. The pulp is subjected to dewatering, washing or displacement by warmer water and thus heating, and calendering. (O.S.).

Development of the electroacoustic dewatering (EAD) process for fine/ultrafine coal: Second quarterly progress report period ending 31 March 1989

Energy Technology Data Exchange (ETDEWEB)

None

1989-04-18

Battelle, in cooperation with the Electric Power Research Institute (EPRI), Ashbrook-Simon-Hartley (ASH), Kaiser Engineers (KE), Lewis Corporation, and Prof. S.H. Chiang of the University of Pittsburgh, is developing an advanced process for the dewatering of fine and ultrafine coals. The advanced process, called Electroacoustic Dewatering (EAD), capitalizes on the adaptation of synergistic effects of electric and acoustic fields to a commercial belt filter press design that is used in many other applications. The EAD equipment is described. 2 figs.

Effect of dewatering on seismic performance of multi-anchor wall due to high ground water level

Science.gov (United States)

Kobayashi, Makoto; Miura, Kinya; Konami, Takeharu; Hayashi, Taketo; Sato, Hiroki

2017-10-01

Previous research reported that the ground water in the backfill of reinforced soil wall made it deteriorate. According to the damage investigation of Great East Earthquake 2011, the reinforced soil structure due to high ground water level by seismic wave were deformed remarkably. Some of them classified ultimate limit state or restorability limit state. However, more than 90% of reinforced soil structure, which suffered from this earthquake, were classified into no damage condition. Therefore, it is necessary that the seismic behaviors of multi-anchor wall due to seepage flow should be clarified in order to adopt the performance-based design in such reinforced soil structure. In this study, a series of centrifugal shaking table tests were conducted to investigate the seismic behavior of multi-anchor wall due to high ground water level. The reinforced drainage pipes were installed into the backfill in order to verify the dewatering effect and additional reinforcement. Furthermore, to check only the dewatering effect, the model tests was carried out with several ground water table that was modeled the case reinforced drainage pipes installed. The test results show unique behavior of reinforced region that moved integrally. This implies that the reinforced region has been behaved as if it became one mass, and this behavior make this structure increase seismic performance. Thus, the effectiveness of dewatering was observed remarkably because of decreasing the inertial force during earthquake.

Improvements in or relating to dewatering of materials

International Nuclear Information System (INIS)

Lane, E.S.; Lyon, C.E.; Simpson, M.P.; Wace, P.F.

1980-01-01

A process is described for the dewatering of a gel precipitated gel body having an open porous network comprising contacting the gel body containing water with an organic liquid capable of extracting water from the gel body thereby to extract water from the gel body, the organic liquid and conditions under which the contacting is effected being chosen such that organic liquid permeates the gel body so as to maintain an open porous network as water is extracted and such that an open porous network remains after removal of organic liquid. Examples are given of the use of the process in the preparation of spherical particles of (U,Th)O 2 and (U,Pu)O 2 . (author)

Textural evidence for jamming and dewatering of a sub-surface, fluid-saturated granular flow

Science.gov (United States)

Sherry, T. J.; Rowe, C. D.; Kirkpatrick, J. D.; Brodsky, E. E.

2011-12-01

Sand injectites are spectacular examples of large-scale granular flows involving migration of hundreds of cubic meters of sand slurry over hundreds of meters to kilometers in the sub-surface. By studying the macro- and microstructural textures of a kilometer-scale sand injectite, we interpret the fluid flow regimes during emplacement and define the timing of formation of specific textures in the injected material. Fluidized sand sourced from the Santa Margarita Fm., was injected upward into the Santa Cruz Mudstone, Santa Cruz County, California. The sand injectite exposed at Yellow Bank Beach records emplacement of both hydrocarbon and aqueous sand slurries. Elongate, angular mudstone clasts were ripped from the wall rock during sand migration, providing evidence for high velocity, turbid flow. However, clast long axis orientations are consistently sub-horizontal suggesting the slurry transitioned to a laminar flow as the flow velocity decreased in the sill-like intrusion. Millimeter to centimeter scale laminations are ubiquitous throughout the sand body and are locally parallel to the mudstone clast long axes. The laminations are distinct in exposure because alternating layers are preferentially cemented with limonite sourced from later groundwater infiltration. Quantitative microstructural analyses show that the laminations are defined by subtle oscillations in grain alignment between limonite and non-limonite stained layers. Grain packing, size and shape distributions do not vary. The presence of limonite in alternating layers results from differential infiltration of groundwater, indicating permeability changes between the layers despite minimal grain scale differences. Convolute dewatering structures deform the laminations. Dolomite-cemented sand, a signature of hydrocarbon saturation, forms irregular bodies that cross-cut the laminations and dewatering structures. Laminations are not formed in the dolomite-cemented sand. The relative viscosity difference

Decide, design, and dewater de waste: A blueprint from Fitzpatrick

International Nuclear Information System (INIS)

Robert, D.E.

1994-01-01

Using a different process to clean concentrated waste tanks at the James A. FitzPatrick nuclear power plant in New York saved nearly half million dollars. The plan essentially allowed processing concentrator bottoms as waste sludge (solidification versus dewatering) that could still meet burial ground requirements. The process reduced the volume from 802.2 to 55 cubic feet. This resin throwaway system eliminated chemicals in the radwaste systems and was designed to ease pressure on the pradwaste processing system, reduce waste and improve plant chemistry. This article discusses general aspects of the process

Insight into effects of electro-dewatering pretreatment on nitrous oxide emission involved in related functional genes in sewage sludge composting.

Science.gov (United States)

Wang, Ke; Wu, Yiqi; Wang, Zhe; Wang, Wei; Ren, Nanqi

2018-05-26

Electro-dewatering (ED) pretreatment could improve sludge dewatering performance and remove heavy metal, but the effect of ED pretreatment on nitrous oxide (N 2 O) emission and related functional genes in sludge composting process is still unknown, which was firstly investigated in this study. The results revealed that ED pretreatment changed the physicochemical characteristics of sludge and impacted N 2 O related functional genes, resulting in the reduction of cumulative N 2 O emission by 77.04% during 60 days composting. The higher pH and NH 4 + -N, but lower moisture, ORP and NO 2 - -N emerged in the composting of ED sludge compared to mechanical dewatering (MD) sludge. Furthermore, ED pretreatment reduced amoA, hao, narG, nirK and nosZ in ED sludge on Day-10 and Day-60 of composting. It was found that nirK reduction was the major factor impacting N 2 O generation in the initial composting of ED sludge, and the decline of amoA restricted N 2 O production in the curing period. Copyright © 2018 Elsevier Ltd. All rights reserved.

Dewatering of sludge using the hydrosoft high-pressure process; Entwaessern von Schlaemmen mit dem Hydrosoft-Hochdruckverfahren

Energy Technology Data Exchange (ETDEWEB)

Eder, C.; Eder, G. [Christian Eder Technology GbR, Neunkirchen (Germany)

1999-07-01

The hydrosoft process permits to dewater sludge, especially also sludge from municipal sewage treatment plant, until it contains a high proportion of dry substance. For existing dewatering systems equipped with the long-lived chamber filter presses, too, the dry matter content of the filter cake can be substantially increased using the hydrosoft process; only the pump system must be retrofitted. As a preliminary measure, tests with mobile pilot plants should be carried out. (orig.) [German] Mit dem Hydrosoft-Verfahren besteht die Moeglichkeit Schlaemme, insbesondere auch Schlaemme aus kommunalen Klaeranlagen, auf hohe Trockensubstanz-Gehalte zu entwaessern. Auch bei bestehenden Entwaesserungsanlagen, die mit den langlebigen Kammerfilterpressen ausgeruestet sind, koennen die Trockensubstanzgehalte der Filterkuchen mit dem Hydrosoft-Verfahren, fuer das dann nur noch das Pumpsystem nachgeruestet werden muss, wesentlich angehoben werden. Vorausgehen sollten jeweils Vorversuche mit mobilen Versuchsanlagen. (orig.)

A case study on stratified settlement and rebound characteristics due to dewatering in Shanghai subway station.

Science.gov (United States)

Wang, Jianxiu; Huang, Tianrong; Sui, Dongchang

2013-01-01

Based on the Yishan Metro Station Project of Shanghai Metro Line number 9, a centrifugal model test was conducted to investigate the behavior of stratified settlement and rebound (SSR) of Shanghai soft clay caused by dewatering in deep subway station pit. The soil model was composed of three layers, and the dewatering process was simulated by self-invention of decompressing devise. The results indicate that SSR occurs when the decompression was carried out, and only negative rebound was found in sandy clay, but both positive and negative rebound occurred in the silty clay, and the absolute value of rebound in sandy clay was larger than in silty clay, and the mechanism of SSR was discussed with mechanical sandwich model, and it was found that the load and cohesive force of different soils was the main source of different responses when decompressed.

Possibility of sludge conditioning and dewatering with rice husk biochar modified by ferric chloride.

Science.gov (United States)

Wu, Yan; Zhang, Panyue; Zhang, Haibo; Zeng, Guangming; Liu, Jianbo; Ye, Jie; Fang, Wei; Gou, Xiying

2016-04-01

Rice husk biochar modified by FeCl3 (MRB-Fe) was used to enhance sludge dewaterability in this study. MRB-Fe preparation conditions and dosage were optimized. Mechanisms of MRB-Fe improving sludge dewaterability were investigated. The optimal modification conditions were: FeCl3 concentration, 3mol/L; ultrasound time, 1h. The optimal MRB-Fe dosage was 60% DS. Compared with raw sludge, the sludge specific resistance to filtration (SRF) decreased by 97.9%, the moisture content of sludge cake decreased from 96.7% to 77.9% for 6min dewatering through vacuum filtration under 0.03MPa, the SV30% decreased from 96% to 60%, and the net sludge solids yield (YN) increased by 28 times. Positive charge from iron species on MRB-Fe surface counteracted negative charge of sludge flocs to promote sludge settleability and dewaterability. Meanwhile, MRB-Fe kept a certain skeleton structure in sludge cake, making the moisture pass through easily. Using MRB-Fe, therefore, for sludge conditioning and dewatering is promising. Copyright © 2016. Published by Elsevier Ltd.

Mine dewatering and impact assessment in an arid area: Case of Gulf region.

Science.gov (United States)

Yihdego, Yohannes; Drury, Len

2016-11-01

Analytical and empirical solution coupled with water balance method were used to predict the ground water inflow to a mine pit excavated below the water table, final pit lake level/recovery and radius of influence, through long-term and time variant simulations. The solution considers the effect of decreased saturated thickness near the pit walls, distributed recharge to the water table and upward flow through the pit bottom. The approach is flexible to accommodate the anisotropy/heterogeneity of the real world. Final pit void water level was assessed through scenarios to know whether it will be consumed by evaporation and a shallow lake will form or not. The optimised radius of influence was estimated which is considered as crucial information in relation to the engineering aspects of mine planning and sustainable development of the mine area. Time-transient inflow over a period of time was estimated using solutions, including analytical element method (AEM). Their primary value is in providing estimates of pit inflow rates to be used in the mine dewatering. Inflow estimation and recovery helps whether there is water to supplement the demand and if there is any recovery issue to be dealt with in relation to surface and groundwater quality/eco-system, environmental evaluations and mitigation. Therefore, this method is good at informing decision makers in assessing the effects of mining operations and developing an appropriate water management strategy.

A Case Study on Stratified Settlement and Rebound Characteristics due to Dewatering in Shanghai Subway Station

Directory of Open Access Journals (Sweden)

Jianxiu Wang

2013-01-01

Full Text Available Based on the Yishan Metro Station Project of Shanghai Metro Line number 9, a centrifugal model test was conducted to investigate the behavior of stratified settlement and rebound (SSR of Shanghai soft clay caused by dewatering in deep subway station pit. The soil model was composed of three layers, and the dewatering process was simulated by self-invention of decompressing devise. The results indicate that SSR occurs when the decompression was carried out, and only negative rebound was found in sandy clay, but both positive and negative rebound occurred in the silty clay, and the absolute value of rebound in sandy clay was larger than in silty clay, and the mechanism of SSR was discussed with mechanical sandwich model, and it was found that the load and cohesive force of different soils was the main source of different responses when decompressed.

Combined treatment of solar energy and gamma irradiation to eliminate pathogenic bacteria in dewatered sludge

International Nuclear Information System (INIS)

Hilmy, N.; Harsoyo, S.; Suwirma, S.

1987-01-01

Combined treatment of solar energy and gamma irradiation to eliminate pathogenic bacteria in dewatered sludge. A combined treatment of solar energy and gamma irradiation has been done to eliminate the pathogenic microbes contaminating dewatered sludge. Samples were collected during dry season, i.e. from June to September 1985. To reduce the water content from 70% to 20%, solar energy from sun rays was used, i.e. from 9 a.m. to 2 p.m. for 4 days. Total bacterial count coliform bacteria Escherichia coli, Fecal Streptococcus, Enterobacteriaceae, and Pseudomonas sp were found to be 7.4x10 8 per g, 4.1x10 3 per g, 4.5x10 2 per g, 3.1x10 5 per g, 3.6x10 4 per g, and 5.4x10 3 per g of samples respectively. The combined treatment could reduce the irradiation dose needed to eliminate the pathogenic microbes of samples investigated from 6 to 2 kGy. (author). 5 figs, 11 refs

Bioelectrochemically-assisted anaerobic composting process enhancing compost maturity of dewatered sludge with synchronous electricity generation.

Science.gov (United States)

Yu, Hang; Jiang, Junqiu; Zhao, Qingliang; Wang, Kun; Zhang, Yunshu; Zheng, Zhen; Hao, Xiaodi

2015-10-01

Bioelectrochemically-assisted anaerobic composting process (AnCBE) with dewatered sludge as the anode fuel was constructed to accelerate composting of dewatered sludge, which could increase the quality of the compost and harvest electric energy in comparison with the traditional anaerobic composting (AnC). Results revealed that the AnCBE yielded a voltage of 0.60 ± 0.02 V, and total COD (TCOD) removal reached 19.8 ± 0.2% at the end of 35 d. The maximum power density was 5.6 W/m(3). At the end of composting, organic matter content (OM) reduction rate increased to 19.5 ± 0.2% in AnCBE and to 12.9 ± 0.1% in AnC. The fuzzy comprehensive assessment (FCA) result indicated that the membership degree of class I of AnCBE compost (0.64) was higher than that of AnC compost (0.44). It was demonstrated that electrogenesis in the AnCBE could improve the sludge stabilization degree, accelerate anaerobic composting process and enhance composting maturity with bioelectricity generation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermophilic anaerobic co-digestion of sewage sludge with grease waste: Effect of long chain fatty acids in the methane yield and its dewatering properties

International Nuclear Information System (INIS)

Silvestre, G.; Illa, J.; Fernández, B.; Bonmatí, A.

2014-01-01

Highlights: • Thermophilic anaerobic codigestion of sewage sludge and grease waste (GW) doubles methane yield. • High GW doses in the influent leads to instability and LCFA accumulation in the effluent. • GW addition promotes acetoclastic activity whilst worsening the hydrogenothrophic activity. • The mesophilic codigestion with GW performs better than the thermophilic one. - Abstract: Thermophilic co-digestion of sewage sludge with three different doses of trapped grease waste (GW) from the pre-treatment of a WWTP has been assessed in a CSTR bench-scale reactor. After adding 12% and 27% of grease waste (on COD basis), the organic loading rate increased from 2.2 to 2.3 and 2.8 kg COD m −3 d −1 respectively, and the methane yield increased 1.2 and 2.2 times. Further GW increase (37% on COD basis) resulted in an unstable methane yield and in long chain fatty acids (LCFA) accumulation. Although this inestability, the presence of volatile fatty acids in the effluent was negligible, showing good adaptation to fats of the thermophilic biomass. Nevertheless, the presence of LCFA in the effluent worsens its dewatering properties. Specific methanogenic activity tests showed that the addition of grease waste ameliorates the acetoclastic activity in detriment of the hydrogenotrophic activity, and suggests that the tolerance to LCFA can be further enhanced by slowly increasing the addition of lipid-rich materials

Preconcentration of a low grade uranium ore in CPDU and laboratory investigation to optimize the dewatering conditions of the preconcentration products

International Nuclear Information System (INIS)

Cristovici, M.A.; Berry, T.F.; Raicevic, M.M.; Brady, E.L.; Bredin, E.L.; Leigh, G.W.; Rouleau, J.P.

1982-04-01

A process consisting of pyrite flotation and magnetic concentration of radionuclides was developed by CANMET over several years, to preconcentrate low grade uranium ores prior to leaching. When the economics of the preconcentration-leaching technology was compared with the leaching of the entire ore after pyrite flotation (Base Case variant), the preconcentration method appeared to be economically less advantageous than expected, due to the high cost of dewatering the preconcentration products. Further investigations examined in-depth the metallurgy and dewatering of the two variants: preconcentration and base case. A typical low grade uranium ore from Elliot Lake area was used. The metallurgy was compared based on data from continuous operation (CPDU). In the preconcentration variant the amount of ore directed to leaching was reduced to more than one third of that processed in the base case, while the radionuclide concentration became more than three times higher. However, by preconcentration 7% of the uranium was lost before leaching. Systematic laboratory-scale settling and filter tests optimized the dewatering conditions of the preconcentration technology to the extent that rates similar to those of the base case were obtained

Modelagem do processo de desidratação de lodo anaeróbio em leitos de secagem simulados Anaerobic sludge dewatering process modeling in simulated drying beds

Directory of Open Access Journals (Sweden)

Sérgio R. A. Soares

2001-05-01

Full Text Available O emprego de leitos de secagem para a desidratação de lodo de descarte de reatores UASB, constitui excelente alternativa, face a sua simplicidade operacional e aos reduzidos custos de implantação. Este trabalho apresenta uma análise dos fenômenos que influenciam o processo de desidratação de lodo anaeróbio, a partir de simulação de leitos de secagem. Neste sentido, são feitas considerações sobre as características e o comportamento do lodo durante cada fase da secagem. Sugere-se também, um modelo matemático para representar o processo de secagem, obtido a partir dos dados experimentais.The employment of drying beds is an excellent option for dewatering of UASB reactor discarded sludge, because of their simple operation and low construction costs. This paper presents an anaerobic sludge dewatering process analysis of the most influential phenomenon based on drying beds simulation. Therefore, some considerations were made about sludge characteristics and behavior during each dewatering stage. A mathematical model for dewatering process representation obtained from experimental data is also suggested.

Application of Fuzzy Synthetic Evaluation in Selection of Best Sludge Dewatering Option in Ghods Town WWTP in Tehran

Directory of Open Access Journals (Sweden)

Masoud Taheriyoun

2015-03-01

Full Text Available The design and upgrade of sludge treatment systems generally depend on the decision made regarding the appropriate system from among the options available. The selection process has become increasingly important and complex due to recent technological developments that have led to increased diversity in the available options which offer a wide variety of capabilities. The multi-criteria decision making method is one of the techniques recently developed which takes into account all the criteria involved in the decision making process. The Ghods Town WWTP in the west of Tehran located in the vicinity of residential areas has given rise to claims by citizens due to the odors emitted by the sludge sand drying bed, which justifies the replacement of the present sludge dewatering system. For this purpose, the multi-criteria decision making method based on the fuzzy synthetic evaluation method was used to identify the optimal sludge dewatering system appropriate for the WWTP under consideration. Furthermore, weighting of the subjective (social, environmental, and administrative criteria was accomplished using the analytical hierarchy process and the objective (i.e., economic criteria were weighted using the entropy concept. In this method, the triangular fuzzy membership function was also used to take into account the uncertainty associated with each of the decision making parameters. Based on the results obtained, the belt filter press dewatering system and the filter press were identified as the preferred solutions.

Dewatering e bonifica dell’ area ˝ex Whitehead Motofides˝ (Pisa, Italia

Directory of Open Access Journals (Sweden)

Nicola Conti

2014-12-01

Full Text Available In 2007 the activities for the remediation of the “ex-Whitehead Motofides area” (in Marina di Pisa, Italy started. In order to allow the contaminated soil excavation in dry conditions a dewatering system was necessary. The water pumped through this system was then treated in an adequate plant. Acque Industriali realized and managed the whole system. The dewatering system was made of suction pins fixed to a depth of 5.5 m, connected by a junction manifold to the suction and booster vacuum assisted pump, which allowed the groundwater release toward the plant. The treatment plant, entirely designed by Acque Industriali and called ITAM (Impianto di Trattamento Acque di Falda Mobile, which means movable groundwater treatment, was realized and set up at the end of 2008. It consisted of a pre-treatment section, made of reinforced concrete, prefabricated nitrogen sweep elements, and a physical chemical treatment plant, in a continuous loop, completely made on skid. The plant, with 25 m3/h of maximum potential, was able to remove possible sedimentable or in suspension material particles from water, iron, manganese, residual organic substances such as hydrocarbons, solvents (chlorinated and not, PCBs, and partly heavy metals. Totally, 98,167 m3 of groundwater were managed in about 25 months of activity. The analytic input and output results confirmed extremely high and satisfactory pollutant removal efficiency. The concentration values of the pollutants, in fact, were always lower than the limits imposed by law.

An assessment of filter aids and filter cloths in the dewatering of intermediate level wastes

International Nuclear Information System (INIS)

Knibbs, R.H.; Hudson, B.C.; Blackwell, J.C.W.

1984-12-01

This report considers a range of filter cloths and precoat materials intended for use in dewatering intermediate level radioactive wastes, and their interaction when used on a rotary drum vacuum filter. The report outlines the advantages and disadvantages of various grades and types of precoat and shows that grades with permeabilities in the intermediate range, 3 to 4 x 10 -12 m 2 , give satisfactory filtrate quality together with ease of operation. The work on filter cloths shows that: radiation damage is not a limiting factor as regards operational life for any of the cloths examined; polyester-based cloths are unsuitable due to their poor resistance to alkali attack; polyamide cloths are satisfactory; and stainless steel Dutch weave cloths are satisfactory and have the added advantage of high strength. The report also briefly considers the radiation resistance of two elastomeric membranes used on the 'epidermal' filter and shows that the natural latex rubber membrane is considerably more resistant to radiation than the silicone rubber membrane and has an estimated operational life of at least 1200 hours when dewatering Magnox silo sludge or α-contaminated alumino ferric flocs. (author)

Efficient dewatering of bark in heated presses. Survey and pilot-scale trials; Effektivare avvattning av bark i vaermda pressar. Problemkartering samt foersoek i pilotskala

Energy Technology Data Exchange (ETDEWEB)

Haakansson, Martin; Stenstroem, Stig (Lund Inst. of Technology, Lund (SE))

2007-12-15

Dewatering and drying of biofuels such as bark and GROT have received increased importance due to an increased interest to use these products as energy sources. In Sweden there are about 30 bark presses installed, however the amount of available information is very limited about dewatering of bark. The goal with this work is to increase the knowledge about dewatering of bark. Two separate goals have been defined in the project: A. Survey about problems related to dewatering of bark and compilation of operating experiences at Swedish mills. B. Study how different parameters affect bark dewatering at pilot scale experiments. Study different techniques for heating bark and the bark pressing process. The results will mainly be of interest for mills which are handling bark, for municipal power plants who buy wet forest residues (bark, GROT etc.) and for manufacturers of industrial bark pressing equipment. The results show that the dry matter content for birch- and pine bark normally are so high that pressing does not result in dewatering of the barks. Both dry and wet debarking is used and these bark fractions should be pressed separately. On line measurement of the dry matter content for the bark should be used as a standard tool on the bark press. This will facilitate improved control of the bark press during the year. Other conclusions are that smaller bark particles result in an increased dry matter content, large bark- and wood pieces decrease the dewatering in the bark press and that the total residence time in the press nip should be at least 30 seconds. The most common method to take care of bark water is to send it to the evaporators or to the water purification plant. Maintenance of the bark press appears not to be a big problem. Hot pressing can be accomplished in different ways, either the bark press can be heated or the bark can be heated in different ways. The alternatives that have been studied in this project are steaming the bark, heating the bark using

Application of a three-dimensional network model to coal dewatering

Energy Technology Data Exchange (ETDEWEB)

Qamar, I.

1986-01-01

A bond-flow correlated network model has been successfully used to calculate equilibrium desaturation curves, single phase permeabilities and two phase flow properties (dewatering curves) for coal filter cakes. A new method of pore volume assignment is presented in which the pore volume occupied by the large pores (which give a capillary pressure less than 0.5 psia) is assigned to the nodes and the rest is distributed to the bonds according to the pore size distribution. The micrographic pore size distribution, used as an input, is determined experimentally. Equilibrium desaturation curves for -32 mesh, -200 mesh and -100 + 200 mesh coal cakes (Pittsburgh Seam Coal), formed with distilled water, have been calculated. The results for six -32 mesh coal cakes formed with surfactants show that the effect of surfactants can be accounted for by modifying one of the model parameters - the entry diameter constant. A correlation is presented to estimate the modified entry diameter constant using experimentally determined surface tension and contact angle values. The size distribution of particles in dispersed state has been correlated with that in the cake which in turn has been correlated with the pore size distribution. An equilibrium desaturation curve has been successfully calculated for -32 mesh Pittsburgh Seam coal using the pore size distribution estimated from the dispersed particle size distribution. Calculated single phase permeabilities, using a bond-flow correlated network and a simple cubic lattice, agree with the experimental values better than a bond-correlated network using a face-centered cubic lattice.

Dewatering treatments to increase dry matter content of the brown seaweed, kelp (Laminaria digitata ((Hudson) JV Lamouroux)).

Science.gov (United States)

Gallagher, Joe A; Turner, Lesley B; Adams, Jessica M M; Dyer, Philip W; Theodorou, Michael K

2017-01-01

Macroalgal water content is an on-going problem for the use of readily accessible seaweeds in sustainable biorefining, including fuel production. Silage is a reduced-water, compactable, easily stored, transportable material. Ensiling could establish a non-seasonal supply of preserved algal biomass, but requires high initial dry matter content to mitigate environmental pollution risks from effluent. This study investigated potential dewatering methods for kelp harvested throughout the year. Treatments included air-drying, osmotic media and acids. Significant interactions between treatment and harvest-time were observed for traits of interest. Fresh weight loss during treatment was composed of changes in water and dry matter content. Air-drying gave reliable increase in final dry matter content; in summer and autumn 30% dry matter content was reached after 24h. Dilute hydrochloric acid reduced stickiness and rendered material suitable for dewatering by screw-pressing; it may be possible to use the consequent pH reduction to promote efficient preservation. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

An Experimental Study on Axial Temperature Distribution of Combustion of Dewatered Poultry Sludge in Fluidized bed combustor

Directory of Open Access Journals (Sweden)

Abbas A.H.

2016-01-01

Full Text Available A laboratory scale bubbling fluidized bed combustor was designed and fabricated to study the combustion of dewatered poultry sludge at different operational parameters. This paper present a study on the influence of equivalent ratio, secondary to primary air ratio and the fuel feed rate on the temperature distribution along the combustor. The equivalent ratio has been changed between 0.8 to 1.4% under poultry sludge feed rate of 10 kg/h and from 0.8 to 1 under poultry sludge feed rate of 15 kg/h. The secondary to primary air ratio was varied from 0.1 to 0.5 at 0.65 m injection height and 1.25 equivalent ratio. The results showed that these factors had a significant influence on the combustion characteristics of poultry sludge. The temperature distribution along the combustor was found to be strongly dependent on the fuel feed rate and the equivalent ratio and it increased when these two factors increased. However, the secondary air ratio increased the temperature in the lower region of the combustor while no significant effect was observed at the upper region of the combustor. The results suggested that the poultry sludge can be used as a fuel with high thermal combustor efficiency.

Development of Graft Copolymer Flocculant Based on Acrylamide and Acrylic Acid for the dewatering of coal

International Nuclear Information System (INIS)

Mahmoud, G.A.; Abdel Khalek, M.A

2012-01-01

Most coal preparation processes were carried out in water medium. The water content of coal product has a negative impact on handling and specific energy value. The moisture content may be attributed to the proportion of fine coal, which presents the greatest dewatering problem. A novel polymeric flocculant has been developed by graft copolymerization of acrylamide (AAm) with acrylic acid (AAc) using gamma irradiation technique. The grafted copol621621ymer P(AAm/AAc) was characterized by Fourier-transform infrared spectroscopy (FTIR), and thermo-gravimetric analysis (TGA). The effects of reaction parameters, such as total absorbed dose, and monomer concentration on grafting yield were investigated. The flocculation performance of the graft copolymer P(AAm/AAc) was investigated in coal suspension. It was observed that the grafting ratio was one of the key factors for the flocculating effects. The copolymers with various grafting ratios showed different flocculating properties. It was found that as the grafting ratio increased, the flocculating effect also increased. The flocculation performance of the grafted copolymer was better than that of the commercial flocculant, poly-acrylamide (Magnafloc 1011).

Thermophysical properties of reconsolidating crushed salt.

Energy Technology Data Exchange (ETDEWEB)

Bauer, Stephen J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Urquhart, Alexander [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-03-01

Reconsolidated crushed salt is being considered as a backfilling material placed upon nuclear waste within a salt repository environment. In-depth knowledge of thermal and mechanical properties of the crushed salt as it reconsolidates is critical to thermal/mechanical modeling of the reconsolidation process. An experimental study was completed to quantitatively evaluate the thermal conductivity of reconsolidated crushed salt as a function of porosity and temperature. The crushed salt for this study came from the Waste Isolation Pilot Plant (WIPP). In this work the thermal conductivity of crushed salt with porosity ranging from 1% to 40% was determined from room temperature up to 300°C, using two different experimental methods. Thermal properties (including thermal conductivity, thermal diffusivity and specific heat) of single-crystal salt were determined for the same temperature range. The salt was observed to dewater during heating; weight loss from the dewatering was quantified. The thermal conductivity of reconsolidated crushed salt decreases with increasing porosity; conversely, thermal conductivity increases as the salt consolidates. The thermal conductivity of reconsolidated crushed salt for a given porosity decreases with increasing temperature. A simple mixture theory model is presented to predict and compare to the data developed in this study.

Bacterial pathogen indicators regrowth and reduced sulphur compounds' emissions during storage of electro-dewatered biosolids.

Science.gov (United States)

Navab-Daneshmand, Tala; Enayet, Samia; Gehr, Ronald; Frigon, Dominic

2014-10-01

Electro-dewatering (ED) increases biosolids dryness from 10-15 to 30-50%, which helps wastewater treatment facilities control disposal costs. Previous work showed that high temperatures due to Joule heating during ED inactivate total coliforms to meet USEPA Class A biosolids requirements. This allows biosolids land application if the requirements are still met after the storage period between production and application. In this study, we examined bacterial regrowth and odour emissions during the storage of ED biosolids. No regrowth of total coliforms was observed in ED biosolids over 7d under aerobic or anaerobic incubations. To mimic on-site contamination during storage or transport, ED samples were seeded with untreated sludge. Total coliform counts decreased to detection limits after 4d in inoculated samples. Olfactometric analysis of ED biosolids odours showed that odour concentrations were lower compared to the untreated and heat-treated control biosolids. Furthermore, under anaerobic conditions, odorous reduced sulphur compounds (methanethiol, dimethyl sulphide and dimethyl disulphide) were produced by untreated and heat-treated biosolids, but were not detected in the headspaces above ED samples. The data demonstrate that ED provides advantages not only as a dewatering technique, but also for producing biosolids with lower microbial counts and odour levels. Copyright © 2014 Elsevier Ltd. All rights reserved.

Dewatering of Chlorella pyrenoidosa using diatomite dynamic membrane: filtration performance, membrane fouling and cake behavior.

Science.gov (United States)

Zhang, Yalei; Zhao, Yangying; Chu, Huaqiang; Zhou, Xuefei; Dong, Bingzhi

2014-01-01

The diatomite dynamic membrane (DDM) was utilized to dewater Chlorella pyrenoidosa of 2 g dry weight/L under continuous-flow mode, whose ultimate algae concentration ranged from 43 g to 22 g dry weight/L of different culture time. The stable flux of DDM could reach 30 L/m(2) h over a 24 h operation time without backwash. Influences of extracellular organic matters (EOM) on filtration behavior and membrane fouling were studied. The DDM was divided into three sub-layers, the slime layer, the algae layer and the diatomite layer from the outside to the inside of the cake layer based on components and morphologies. It was found that EOM caused membrane fouling by accumulating in the slime and algae layers. The DDM intercepted polysaccharides, protein-like substances, humic-like substances and some low-MW organics. Proteins were indicated the major membrane foulants with increased protein/polysaccharide ratio from the slime layer to the diatomite layer as culture time increased. This method could be applied to subsequent treatment of microalgae coupling technology of wastewater treatment or microalgae harvesting for producing biofuel. Copyright © 2013 Elsevier B.V. All rights reserved.

Performance of Sandy Dry Beds for sludge dewatering

International Nuclear Information System (INIS)

Al-Muzaini, S.

2003-01-01

Sludge produced by the Jahra treatment plant was assessed. The assessment was directed at determining the performance of sand drying beds. The assessment of quality of the sludge produced was based on the standards for land application of sewage sludge. Analyses were carried out for trace heavy metals and bacteria. The results of analyses showed that the sludge produced was high in organic matter and sand content but low in heavy metals. The collected data indicated that the sand drying beds at the Jahra treatment plant are at present inadequate to handle the projected sludge production. The investigation showed that the sand drying beds are fully used and the plant will require 3-4 times the capacity of the existing drying beds when the plant becomes fully operational. In addition, these sand drying beds are subjected to uncontrollable conditions such as temperature, rainfall and sludge drainage rate. Thus, sand drying beds have become less popular as a dewatering system. This paper evaluates the performance of the existing sand drying beds and suggests the most appropriate technology to alleviate the above mentioned problems. (author)

Characteristics of water obtained by dewatering cyanobacteria-containing sludge formed during drinking water treatment, including C-, N-disinfection byproduct formation.

Science.gov (United States)

Xu, Hangzhou; Pei, Haiyan; Jin, Yan; Xiao, Hongdi; Ma, Chunxia; Sun, Jiongming; Li, Hongmin

2017-03-15

This is the first study to systematically investigate the characteristics of the water obtained by dewatering cyanobacteria-containing sludge generated in the drinking water treatment plant, including formation of C- and N-disinfection by-products (DBPs). Results showed that this 'dewatering water' (DW) had different properties when the sludge was stored at different times. The content of dissolved organic matter (DOM) and microcystins (MCs) in the DW were low when the sludge was treated or disposed of within 4 days; correspondingly, the C-, N-DBP production was also low. However, due to the damage of algal cells to some extent, the DOM and MC levels increased significantly for storage time longer than 4 days; the production of C-, N-DBPs also increased. There were also obvious differences in the characteristics of the DW from sludges generated with different coagulant species. Due to the better protective effect of FeCl 3 and polymeric aluminium ferric chloride (PAFC) flocs, the DOM and MC levels and the production of C-, N-DBPs in the DW with FeCl 3 and PAFC coagulation were lower than those with AlCl 3 coagulation, even though the sludges were stored for the same amount of time. Furthermore, because of the formation of Al and Fe hydroxides, precipitated onto the surface of flocs, the soluble Al and Fe in the DW decreased with increased storage time, especially in the first four days. Overall, this study revealed the trends in variation of DW quality for cyanobacteria-containing sludges formed with different coagulants, then FeCl 3 and PAFC coagulants are recommended and sludge should be treated or disposed of within 4 days. Copyright © 2017 Elsevier Ltd. All rights reserved.

The use of geotextile tube containers for dewatering the Restigouche open pit zinc mine and settling pond basin in New Brunswick, Canada

Energy Technology Data Exchange (ETDEWEB)

Douheret [Terratube, Saint-Romuald, PQ (Canada)

2010-07-01

This PowerPoint presentation discussed the use of geotextile tube containers for the dewatering of an open pit zinc mine and settling pond in New Brunswick (NB). The zinc and lead mine closed in 1996 and will be re-opened in 2007. Remediation of the site has been challenged by severe discharge criteria for treated water, as well as by the different types of wastewater produced at the site, which is located in a mountainous area with no impermeable soil. The remediation projects include an open pit cleaning procedure where water is removed and the mine is then desludged. A wastewater treatment plant will then be installed. More than 32,000 m{sup 3} of sludge has accumulated at the bottom of the pit. The zinc content of the sludge was estimated at 2.5 ppm. The water management phase of the project will include batch treatments and the addition of 140 metric tonnes of lime to raise the pH and to precipitate metal ions. The sludge management program included the use of mechanical dewatering, the construction of a storage area, and the use of geocontainers for dewatering and temporary containment. Seventeen geotextile containers were used to reduce the zinc content of the water to less than the 250 ppb authorized by environmental agencies. The containers were changed once every 2 months. tabs., figs.

Predicting spread of invasive exotic plants into de-watered reservoirs following dam removal on the Elwha River, Olympic National Park, Washington

Science.gov (United States)

Woodward, Andrea; Torgersen, Christian E.; Chenoweth, Joshua; Beirne, Katherine; Acker, Steve

2011-01-01

The National Park Service is planning to start the restoration of the Elwha River ecosystem in Olympic National Park by removing two high head dams beginning in 2011. The potential for dispersal of exotic plants into dewatered reservoirs following dam removal, which would inhibit restoration of native vegetation, is of great concern. We focused on predicting long-distance dispersal of invasive exotic plants rather than diffusive spread because local sources of invasive species have been surveyed. We included the long-distance dispersal vectors: wind, water, birds, beavers, ungulates, and users of roads and trails. Using information about the current distribution of invasive species from two surveys, various geographic information system techniques and models, and statistical methods, we identified high-priority areas for Park staff to treat prior to dam removal, and areas of the dewatered reservoirs at risk after dam removal.

Environmental control of drilling mud discharge through dewatering in cold weather climates

International Nuclear Information System (INIS)

Wojtanowicz, A.K.

1991-01-01

The paper presents results of an experimental study into the effect of drilling mud temperature upon the dewatering performance. Three temperature ranges were considered: from flowline temperature to room temperature, from room temperature to freezing point, and the freeze (4 degrees F)/thaw (54 degrees F) cycle. The tested drilling fluids included unweighted and weighted fresh water muds and a weighted salt water mud. a sealed laboratory batch reactor was used in the experiments to prevent rapid vaporization of separated water at temperatures above 140 degrees F. Also, ice or ice-salt baths were utilized for deep freezing. The dewaterability (net water removal) was measured with a bench-top plate press under constant expression pressure 30 psi

Detecting Dewatering of Peatland Pastures Using Sentinel-1 Satellite Radar Interferometry.

Science.gov (United States)

Heuff, F.; Samiei-Esfahany, S.; van Leijen, F. J.; Hanssen, R. F.

2017-12-01

The Netherlands are famous for their polders and the draining of soils to be used as pastures. Around 30% of the pastures are situated on peat soils, mostly in the western part of the Netherlands. Peat is composed of organic materials that oxidize and emit greenhouse gases when exposed to air. Oxidation of peat soils results in volume reduction and subsequent subsidence. As a result, the groundwater level rises relative to the surface. Consequently, the soil needs to be dewatered to keep it sufficiently dry for farming, resulting in more oxidation, and therefore more subsidence. This process is bound to continue until the peat soils have disappeared completely. The societal cost of land subsidence due to peat soils are estimated to be 5200 million euro for urban areas and 200 million euro for peatland pastures, for a period until 2050. Measuring the subsidence is not straightforward, if not impossible, with conventional geodetic means as soft soils make it impossible to install fixed benchmarks for repeated surveying. Also, due to the very fast temporal decorrelation over pastures, conventional InSAR approaches cannot measure a signal due to loss of coherence. Here we deploy a complete set of available SAR data from Sentinel-1, Radarsat-2 and TerraSAR-X to estimate the spatio-temporally varying subsidence signal due to the dewatering of peatland pastures over the western part of the Netherlands. We compute the InSAR coherence matrix for all possible interferometric combination, and compute an equivalent single-master stack to estimate the subsidence. Using terrain and land-use defined coherence estimation areas we optimize the phase estimation over areas severely affected by temporal decorrelation. This leads to a first estimate of deformation signals correlated with ancient shallow soil structures due to fluviatile structures. We use the methodology to investigate the effect of advanced local drainage schemes to slow down the subsidence phenomena.

Impact of sludge properties on solid-liquid separation of activated sludge

DEFF Research Database (Denmark)

Christensen, Morten Lykkegaard

2016-01-01

Solid-liquid separation of activated sludge is important both directly after the biological treatment of wastewater and for sludge dewatering. The separation of solid from the treated wastewater can be done by clarifiers (conventional plants) or membrane (MBR). Further, part of the sludge is taken...... out from the proces and usually dewatered before further handling. The separation process is costly. Moreover, the separation process depends on the composition and the properties of the sludge. The best separation is obtained for sludge that contains strong, compact flocs without single cells...... and dissolved extracellular polymeric substances (EPS). Polyvalent ions improve the floc strangth and improve the separation whereas monovalent ions (e.g. from road salt, sea water intrusion and industry) reduces impair the separation. Further high pH impairs the separation process due to floc disintegration...

Influence of Macroeconomic Factors on Residential Property ...

African Journals Online (AJOL)

Sultan

exerted by macroeconomic factors on residential property returns in Abuja. The backward .... explanatory power and positive influence of employment and ...... Project. Management In Property Development: the Nigeria experience. Ibadan:.

Dewatering of contaminated river sediments

Science.gov (United States)

Church, Ronald H.; Smith, Carl W.; Scheiner, Bernard J.

1994-01-01

Dewatering of slurries has been successfully accomplished by the proper use of polymers in flocculating the fine particulate matter suspended in mineral processing streams. The U.S. Bureau of Mines (USBM) entered into a cooperative research effort with the U.S. Army Corps of Engineers (Corps) for the purpose of testing and demonstrating the applicability of mining flocculation technology to dredging activities associated with the removal of sediments from navigable waterways. The Corps has the responsibility for maintaining the navigable waterways in the United States. Current technology relies primarily on dredging operations which excavate the material from the bottom of waterways. The Corps is testing new dredging technology which may reduce resuspension of sediments by the dredging operation. Pilot plant dredging equipment was tested by the Corps which generated larger quantities of water when compared to conventional equipment, such as the clam shell. The transportation of this 'excess' water adds to the cost of sediment removal. The process developed by the USBM consists of feed material from the barge being pumped through a 4-in line by a centrifugal pump and exiting through a 4-in PVC delivery system. A 1,000-gal fiberglass tank was used to mix the polymer concentrate. The polymer was pumped through a 1-in line using a variable speed progressive cavity pump and introduced to the 4-in feed line prior to passing through a 6-in by 2-ft static mixer. The polymer/feed slurry travels to the clarifying tank where the flocculated material settled to the bottom and allowed 'clean' water to exit the overflow. A pilot scale flocculation unit was operated on-site at the Corps' 'Confined Disposal Facility' in Buffalo, NY.

Development of producing equipment of mixed butane-air with low dew point. Energy saving dewatering apparatus and 6A-Gas producing apparatus utilizing vaporization latent heat of butane and potential heat of air

Energy Technology Data Exchange (ETDEWEB)

Komine, Jin; Okada, Hiroto; Taniue, Nobuo; Tanoue, Keiju; Yamada, Tatsuhiko; Maekawa, Hisami; Murakami, Keiji

1988-02-10

A producing equipment of mixed butane-air with low dew point was developed. The dewatering was made during the period from the middle of May to the middle of October with high atmospheric humidity. The production capacity of the mixed gas is 3000 Nm/sup 3/ of 22% of butane and 78% of air per hour. The designed dew point is 18/sup 0/C or less under the pressure of 0.7 kg/cm/sup 2/G. The saturation temperature is 7.5/sup 0/C after the liquid butane is evacuated by a regulating valve. The air introduced into the dehumidifier through finned tubes is cooled to dewater based on those data. The partially vaporized butane is completely gasified by hot water in a vaporizer and mixed with the dewatered air by a venture mixer to produce the mixed butane-air. When the dewatering is incomplete, the spray nozzle must be just exchanged. The dew point of the produced gas was sufficiently below the designed value. The investment cost is low. The total operating cost is reduced by the remarkably decreased fuel cost though the power cost is increased. The noise level is low and the heat control is easy. (11 figs, 4 tabs, 1 photo)

Vibrating membrane filtration as improved technology for microalgae dewatering.

Science.gov (United States)

Nurra, Claudia; Clavero, Ester; Salvadó, Joan; Torras, Carles

2014-04-01

The effect of shear-enhanced filtration by vibratory process in microalgae dewatering is presented in this paper. The aim of this research was to investigate the technical performance and improvement of vibrating membrane filtration compared with conventional tangential cross-flow filtration in microalgae concentration. An industrial-scale available commercial set-up was used. Several membrane materials as polyethersulfone, polyacrylonitrile, etc., and mean pore sizes (from 7000Da to 0.2μm) were tested and compared in both filtration set-ups. Experiments were carried-out with Nannochloropsis gaditana and Phaeodactylum tricornutum microalgae. It has been demonstrated that, even if the choice of the membrane depends on its cut-off, its material and the type of microalgae filtrated, dynamic filtration is always the best technology over a conventional one. If with conventional filtration permeability values were in the vicinity of 10L/h/m(2)/bar in steady state phase, with dynamic filtration these values increased to 30L/h/m(2)/bar or more. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hydrothermal and alkaline hydrothermal pretreatments plus anaerobic digestion of sewage sludge for dewatering and biogas production: Bench-scale research and pilot-scale verification.

Science.gov (United States)

Li, Chunxing; Wang, Xingdong; Zhang, Guangyi; Yu, Guangwei; Lin, Jingjiang; Wang, Yin

2017-06-15

To test the feasibility and practicability of the process combing hydrothermal pretreatment for dewatering with biogas production for full utilization of sewage sludge, hydrothermal/alkaline hydrothermal pretreatments and in turn anaerobic digestion of the filtrates obtained after dewatering the pretreated sludge were performed at bench- and pilot-scales. The hydrothermal temperature fell within the range of 140 °C-220 °C and the pretreatment time varied from 30 min to 120 min. For the alkaline hydrothermal pretreatment the pH value of the sludge was adjusted to 9.0-11.0 by adding Ca(OH) 2 . The results showed that the dewaterability of the sewage sludge was improved with increasing pretreatment temperature but the impact of the pretreatment time was not significant. The addition of Ca(OH) 2 gave better performance on the subsequent mechanical dewatering of the pretreated sludge compared to pure hydrothermal pretreatment, and the higher the pH value was, the better the dewaterability of the pretreated sludge was. The conditions of 180 °C/30 min and 160 °C/60 min/pH = 10.0 (for hydrothermal and alkaline hydrothermal pretreatments, respectively) resulted in relatively good results in the theoretical energy balance, which were verified in the pilot-scale tests. Based on the data from the pilot tests, the alkaline hydrothermal process realized self-sufficiency in energy at the cost of a proper amount of CaO. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of lignin on properties of wood-inorganic sorbents

International Nuclear Information System (INIS)

Remez, V.P.; Charina, M.V.; Klass, S.M.; Shubin, A.S.; Tkachev, K.V.; Isaeva, O.F.

1986-01-01

Present article is devoted to influence of lignin on properties of wood-inorganic sorbents. The influence of component composition of matrix on sorption properties of sorbents and their stability in different mediums is studied. The dependence of sorption capacity of sorbent on component matrix composition and its porous structure is defined.

WtF‐Nano: One‐Pot Dewatering and Water‐Free Topochemical Modification of Nanocellulose in Ionic Liquids or γ‐Valerolactone

Science.gov (United States)

Laaksonen, Tiina; Helminen, Jussi K. J.; Lemetti, Laura; Långbacka, Jesper; Rico del Cerro, Daniel; Hummel, Michael; Rantamäki, Antti H.; Kakko, Tia; Kemell, Marianna L.; Wiedmer, Susanne K.; Heikkinen, Sami; Kilpeläinen, Ilkka

2017-01-01

Abstract Ionic liquids are used to dewater a suspension of birch Kraft pulp cellulose nanofibrils (CNF) and as a medium for water‐free topochemical modification of the nanocellulose (a process denoted as “WtF‐Nano”). Acetylation was applied as a model reaction to investigate the degree of modification and scope of effective ionic liquid structures. Little difference in reactivity was observed when water was removed, after introduction of an ionic liquid or molecular co‐solvent. However, the viscoelastic properties of the CNF suspended in two ionic liquids show that the more basic, but non‐dissolving ionic liquid, allows for better solvation of the CNF. Vibrio fischeri bacterial tests show that all ionic liquids in this study were harmless. Scanning electron microscopy and wide‐angle X‐ray scattering on regenerated samples show that the acetylated CNF is still in a fibrillar form. 1 D and 2 D NMR analyses, after direct dissolution in a novel ionic liquid electrolyte solution, indicate that both cellulose and residual xylan on the surface of the nanofibrils reacts to give acetate esters. PMID:29112334

Assessment of technical-scale dewatering results in decanters on the basis of measurements of water types in sewage sludge; Bestimmung grosstechnischer Entwaesserungsergebnisse in Dekantern basierend auf der Messung der Wasserarten von Klaerschlaemmen

Energy Technology Data Exchange (ETDEWEB)

Kopp, J.; Dichtl, N. [Technische Univ. Braunschweig (Germany). Inst. fuer Siedlungswasserwirtschaft

1999-07-01

In a sewage sludge suspension, three water portions can be measured and distinguished from each other. The free water portion is not bound to sludge particles and can be separated by mechanical dewatering. The interstitial water portion bound by capillary forces and bound water (on surfaces and in cells) remain in the sludge cake after dewatering. The described measuring system for thermo-gravimetric determination of the water portions of sewage sludge was adjusted and calibrated at Braunschweig Technical University and permits prognosticating the maximum attainable content of solids through mechanical dewatering in high-performance decanters. (orig.) [German] In einer Klaerschlammsuspension koennen drei Wasseranteile messtechnisch unterschieden werden. Der freie Wasseranteil ist nicht an die Schlammpartikel gebunden und ist bei einer maschinellen Entwaesserung abtrennbar. Der kapillar gehaltene Zwischenraumwasseranteil und das gebundene Wasser (auf Oberflaechen und in Zellen) verbleibt nach der Entwaesserung im Schlammkuchen. Die an der TU Braunschweig angepasste und kalibrierte Messanlage zur thermo-gravimetrischen Bestimmung der Wasseranteile eines Klaerschlammes ermoeglicht es, den maximal bei der maschinellen Entwaesserung in Hochleistungsdekantern erreichbaren Feststoffgehalt zu prognostizieren. (orig.)

Effect of hydrothermal treatment temperature on the properties of sewage sludge derived solid fuel

Directory of Open Access Journals (Sweden)

Mi Yan

2015-10-01

Full Text Available High moisture content along with poor dewaterability are the main challenges for sewage sludge treatment and utilization. In this study, the effect of hydrothermal treatment at various temperature (120-200 ˚C on the properties of sewage sludge derived solid fuel was investigated in the terms of mechanical dewatering character, drying character, calorific value and heavy metal distribution. Hydrothermal treatment (HT followed by dewatering process significantly reduced moisture content and improved calorific value of sewage sludge with the optimum condition obtained at 140˚C. No significant alteration of drying characteristic was produced by HT. Heavy metal enrichment in solid particle was found after HT that highlighted the importance of further study regarding heavy metal behavior during combustion. However, it also implied the potential application of HT on sewage sludge for heavy metal removal from wastewater.

Use of a water treatment sludge in a sewage sludge dewatering process

Science.gov (United States)

Górka, Justyna; Cimochowicz-Rybicka, Małgorzata; Kryłów, Małgorzata

2018-02-01

The objective of the research study was to determine whether a sewage sludge conditioning had any impact on sludge dewaterability. As a conditioning agent a water treatment sludge was used, which was mixed with a sewage sludge before a digestion process. The capillary suction time (CST) and the specific filtration resistance (SRF) were the measures used to determine the effects of a water sludge addition on a dewatering process. Based on the CST curves the water sludge dose of 0.3 g total volatile solids (TVS) per 1.0 g TVS of a sewage sludge was selected. Once the water treatment sludge dose was accepted, disintegration of the water treatment sludge was performed and its dewaterability was determined. The studies have shown that sludge dewaterability was much better after its conditioning with a water sludge as well as after disintegration and conditioning, if comparing to sludge with no conditioning. Nevertheless, these findings are of preliminary nature and future studies will be needed to investigate this topic.

STABILIZATION OF DEWATERED SEWAGE SLUDGE BY AEROBIC COMPOSTING METHOD: USING SAWDUST AS BULKING AGENTS

Directory of Open Access Journals (Sweden)

A PARVARESH

2002-12-01

Full Text Available Introduction. Sludge production from municipal wastewater treatment plants should have quality standards before disposal in to the environment. Environmental specialists classified sewage sludge as a hazardous waste because of high organic compounds and pathogenic microorganisms. They belive that sewage should be stabilized before disposal and so composting of sewage sludge is an effective and economical method to stabilize. Sewage sludge compost could be used to improve soil structure and enrich the soil with nutrients. Methods. To evaluate the optimum conditions of aerobic compost, the mixture of dewatered sewage sludge from Isfahan municipal waste water treatment plant and sawdust as bulking agent were used. Pilot scale study were performed in Isfahan municipal waste water treatment plant. To perform this research project, the dewatered sewage sludge with humidity between 78 to 82 percent were mixed with sawdust. Turning over method of the piles with one week interval were applied to aerate the mixture. Temperature of the piles were monitored at different depths daily. Other parameters such as N, G, organic matters and pH were determined weekly. Total and fecal coli form, and salmonella were determined at the beginning and end of the composting process, also heavy metals were measured at the same time. Results. The results of this study showed that after days, temperature of the mixture reached up to 55 G, and were stabled for 15 days. Humidity, organic matter, organic carbon and GIN ratio of the mixture decreased over the period of the study, due to increasing the temperature. Also organic matter and humidity mainly decreased in thermofilic phase. The number of total and fecal coliform and also salmonella decreased to A class standards of US.EPA at the end of the operation. Discussion. The results of the study also showed that, this type of composting method is reliable, and simple to schedule, with high flexibility and low odor

The influence of zeta potential and yield stress on the filtration characteristics of a magnesium hydroxide simulant

International Nuclear Information System (INIS)

Biggs, Simon; Nabi, Rafiq; Poole, Colin; Patel, Ashok

2007-01-01

In the UK, irradiated fuels from Magnox reactors are often stored in water-filled ponds under alkaline conditions, so as to minimise corrosion of fuel cladding. This is important to prevent or reduce leakage of soluble fission products and actinides to the pond water. A variety of intermediate level wastes derived from Magnox materials are stored at power stations. Under these alkaline conditions, various species of magnesium are formed, of which magnesium hydroxide is the dominant material. The particle-fluid interactions are significant for the design and operation of facilities for hydraulic retrieval, filtration, dewatering and ion exchange treatment of fuel storage pond water and stored wet Magnox wastes. Here we describe a study of particulate properties and filtration characteristics of oxide particle simulants under laboratory conditions. Cake and medium resistance data were correlated across a range of pH conditions with electro-acoustic zeta potential and shear yield stress measurements, as a function of particle volume fractions. The influence of zeta potential on filtration properties arises directly from the interaction of particles within the sediment cake. (authors)

Semi-technical experiments in the mechanical solubilization of excess sludge with subsequent anaerobic stabilization; Halbtechnische Versuche zum mechanischen Aufschluss von Ueberschussschlaemmen mit anschliessender anaerober Stabilisierung

Energy Technology Data Exchange (ETDEWEB)

Palmowski, L.; Schwedes, J. [Technische Univ. Braunschweig (Germany). Inst. fuer Mechanische Verfahrenstechnik; Winter, A.; Dichtl, N. [Technische Univ. Braunschweig (Germany). Inst. fuer Siedlungswasserwirtschaft; Schmelz, K.G. [Emschergenossenschaft und Lippeverband, Essen (Germany); Mueller, J. [Technische Univ. Braunschweig (Germany). Inst. fuer Mechanische Verfahrenstechnik; Technische Univ. Braunschweig (Germany). Inst. fuer Siedlungswasserwirtschaft

1999-07-01

Within the framework of this project, the influence of the mechanical disintegration of different types of sludge on their anaerobic degradation behaviour and dewatering properties was investigated on a semi-technical scale. (orig.) [German] Im Rahmen dieses Projektes wurde in halbtechnischem Versuchsmassstab der Einfluss der mechanischen Desintegration verschiedener Schlaemme auf ihr anaerobes Abbauverhalten und ihr Entwaesserungsverhalten untersucht. (orig.)

Engineering properties of nuclear waste slurries - 16378

International Nuclear Information System (INIS)

Biggs, Simon; Fairweather, Michael; Hunter, Timothy; Omokanye, Qanitalillahi; Peakall, Jeffrey

2009-01-01

The type of particulate systems encountered in legacy nuclear waste slurries is highly complicated, with the aggregation and flow behaviour being at times very variable. However, deconstructing the complex overall slurry activity to singular particle-particle interactions can lead to a greater understanding of the mechanisms involved with particle aggregation, and so to predictions of their settling and flow in nuclear systems. Of particular importance to legacy waste is the role of salts in controlling the attraction of particles (and so in dictating the rheological properties of the system) as sludge may contain a variety of specific ions and generally have high ionic conductivity [1]. In this paper, particle-particle interactions are characterised using a number of complimentary methods, and their influence on resulting flow and bed compression is measured. The methods used to characterise the particle-particle interactions under various salt and pH conditions were electro-acoustic analysis (zeta potential) and atomic force microscopy (AFM). Following on from the analysis of particle-particle properties, bulk sediment behaviour was investigated using shear and compressive yield stress measurements, vital parameters in dictating flow and dewatering performance, respectively. Together, these techniques enable the characterisation of a range of particulate systems that may be encountered in legacy wastes, and results point to a number of important factors that can help explain the observed variability in industrial slurry behaviour. (authors)

Influence of Storage on Briquettes Mechanical Properties

Directory of Open Access Journals (Sweden)

Brožek M.

2014-09-01

Full Text Available The effects of the storage place, placing manner, and storage time on mechanical properties of briquettes made from birch chips were laboratorily tested. A unique methodology developed by the present author enabling a relatively easy assessment of mechanical properties of the briquettes is described. The briquettes properties were evaluated by their density and rupture force determination. From the test results it follows that if the briquettes are stored in a well closed plastic bag, neither the place nor the storage time influence significantly their life time. When stored in a net plastic bag, the briquettes get seriously damaged, namely depending on their storage place and storage time.

Process Design and Economics for the Production of Algal Biomass: Algal Biomass Production in Open Pond Systems and Processing Through Dewatering for Downstream Conversion

Energy Technology Data Exchange (ETDEWEB)

Davis, Ryan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Markham, Jennifer [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kinchin, Christopher [National Renewable Energy Lab. (NREL), Golden, CO (United States); Grundl, Nicholas [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tan, Eric C.D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Humbird, David [DWH Process Consulting, Denver, CO (United States)

2016-02-17

This report describes in detail a set of aspirational design and process targets to better understand the realistic economic potential for the production of algal biomass for subsequent conversion to biofuels and/or coproducts, based on the use of open pond cultivation systems and a series of dewatering operations to concentrate the biomass up to 20 wt% solids (ash-free dry weight basis).

The influence of protective properties of packaging materials and ...

African Journals Online (AJOL)

The influence of protective properties of packaging materials and modified atmosphere on quality changes of dried apricot is shown in this paper. In our investigation, we used four different characteristic combinations of packaging materials with different barrier properties for packaging of dried apricot: ...

Reuse of liquid, dewatered, and composted sewage sludge on agricultural land: effects of long-term application on soil and crop.

Science.gov (United States)

Mantovi, Paolo; Baldoni, Guido; Toderi, Giovanni

2005-01-01

To evaluate the effects of repeated sewage sludge applications in comparison to mineral fertilisers on a winter wheat-maize-sugar beet rotation, a field experiment on a silty-loam soil, in the eastern Po Valley (Italy), was carried out since 1988. Municipal-industrial wastewater sludge as anaerobically digested, belt filtered (dewatered), and composted with wheat straw, has been applied at 5 and 10 Mg DM ha(-1)yr(-1). Biosolids gave crop yields similar to the highest mineral fertiliser dressing. However, with the higher rate of liquid and dewatered sludge, excessive N supply was harmful, leading to wheat lodging and poor quality of sugar beet and wheat crops. From this standpoint compost use was safer. Biosolids increased organic matter (OM), total N, and available P in the soil and reduced soil alkalinity, with more evident effects at the highest rate. Compost caused the most pronounced OM top soil accumulation. Significant accumulations of total Zn and Cu were detected in amended top soil, but no other heavy metals (Cd, Cr, Ni, Pb), whose total concentration remained well below the hazard limits. Biosolid applications significantly increased the content of N, P, Zn, and Cu in wheat grain, N and Cu in sugar beet roots, and only Cu in maize grain. The application of biosolids brought about notable benefits to soil fertility but it was associated with possible negative effects on water quality due to increased P availability and on soil ecology due to Zn accumulation.

Dewatering and RCRA partial closure action on solar evaporation ponds, Rocky Flats Plant, Golden, Colorado

International Nuclear Information System (INIS)

1991-06-01

The Department of Energy (DOE) has prepared an Environmental Assessment (DOE/EA-0487) on its proposal to partially close five solar evaporation ponds at the Rocky Flats Plant (RFP) pursuant to the requirements of the Resource Conservation and Recovery Act (RCRA). This proposal would be known as a RCRA partial closure and would be accomplished by dewatering the ponds, where necessary, and converting any remaining sludge or evaporator concentrate to a solid wasteform (pondcrete and saltcrete). The pond sites would be stabilized to prevent erosion or other disturbance to the soil and to prevent infiltration of rain or snowmelt. The solid wasteform would be transported offsite for disposal. The five solar ponds (designated 207-A, 207-B (north, center, and south), and 207-C), are the only solar evaporation ponds that exist at the RFP. A finding of no significant impact is included

Groundwater Sustainability through a Novel Dewatering Technology

Science.gov (United States)

Jin, Y.; Holzbecher, E.; Ebneth, S.

2012-12-01

Groundwater plays a key role in the hydrologic cycle and ecosystem balances. Over the past decades, groundwater is intensively extracted in order to keep construction or mining sites dry. For the latter purpose the pumped water is usually discharged into a nearby surface water body or injected into an aquifer distant from the abstraction sites. As a result, aquifers are depleted and the local eco-system is disrupted as a consequence of falling groundwater tables. Given ongoing pressure on aquifer from abstraction sites, it is vital to bring up adequate attention on groundwater conservation. We demonstrate a novel technique, Düsensauginfiltration (DSI, translated as 'nozzel-suction-infiltration'), which avoids water conveyance but still lowers the groundwater table locally. The method combines abstraction of groundwater at the upper part of the aquifer with injection in the same borehole, but at a greater depth. Hence no water is withdrawn from the system. The method is already used practically in Germany, Netherlands, and China, however, it is not yet fully scientifically understood and evaluated. Currently, two tests sites in Germany, for single and multi well respectively, are selected, at which the DSI technology is currently examined. The project is cooperated with a leading dewatering company (Hoelscher Wasserbau GmbH) and funded by Deutsche Bundesstiftung Umwelt (DBU). To provide the basic principle of the method, we present numerical models solving the differential equation, which is derived from Darcy's Law and mass conservation, describing groundwater flow. We set up stationary numerical models in 2D (vertical cross section for single well case) and 3D (multi well case and/or when ambient groundwater flow is considered) using COMSOL Multiphysics. Since our model region only involves the saturated part of the unconfined aquifer, the numerical model solves a free boundary problem using hydraulic pressure as unknown variable. Two physical modes are included

[Study on influence between activated carbon property and immobilized biological activated carbon purification effect].

Science.gov (United States)

Wang, Guang-zhi; Li, Wei-guang; He, Wen-jie; Han, Hong-da; Ding, Chi; Ma, Xiao-na; Qu, Yan-ming

2006-10-01

By means of immobilizing five kinds of activated carbon, we studied the influence between the chief activated carbon property items and immobilized bioactivated carbon (IBAC) purification effect with the correlation analysis. The result shows that the activated carbon property items which the correlation coefficient is up 0.7 include molasses, abrasion number, hardness, tannin, uniform coefficient, mean particle diameter and effective particle diameter; the activated carbon property items which the correlation coefficient is up 0.5 include pH, iodine, butane and tetrachloride. In succession, the partial correlation analysis shows that activated carbon property items mostly influencing on IBAC purification effect include molasses, hardness, abrasion number, uniform coefficient, mean particle diameter and effective particle diameter. The causation of these property items bringing influence on IBAC purification is that the activated carbon holes distribution (representative activated carbon property item is molasses) provides inhabitable location and adjust food for the dominance bacteria; the mechanical resist-crash property of activated carbon (representative activated carbon property items: abrasion number and hardness) have influence on the stability of biofilm; and the particle diameter size and distribution of activated carbon (representative activated carbon property items: uniform coefficient, mean particle diameter and effective particle diameter) can directly affect the force of water in IBAC filter bed, which brings influence on the dominance bacteria immobilizing on activated carbon.

The influence of Reynolds numbers on resistance properties of jet pumps

Energy Technology Data Exchange (ETDEWEB)

Geng, Q. [Key Laboratory of Cryogenics, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Zhou, G. [Key Laboratory of Cryogenics, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Li, Q. [Key Laboratory of Cryogenics, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); State Key laboratory of Technologies in Space Cryogenic Propellants, Technical Institute of Physics and Chemistry (China)

2014-01-29

Jet pumps are widely used in thermoacoustic Stirling heat engines and pulse tube cryocoolers to eliminate the effect of Gedeon streaming. The resistance properties of jet pumps are principally influenced by their structures and flow regimes which are always characterized by Reynolds numbers. In this paper, the jet pump of which cross section contracts abruptly is selected as our research subject. Based on linear thermoacoustic theory, a CFD model is built and the oscillating flow of the working gas is simulated and analyzed with different Reynolds numbers in the jet pump. According to the calculations, the influence of different structures and Reynolds numbers on the resistance properties of the jet pump are analyzed and presented. The results show that Reynolds numbers have a great influence on the resistance properties of jet pumps and some empirical formulas which are widely used are unsuitable for oscillating flow with small Reynolds numbers. This paper provides a more comprehensive understanding on resistance properties of jet pumps with oscillating flow and is significant for the design of jet pumps in practical thermoacoustic engines and refrigerators.

Some properties of Suncor oil sands tailings

Energy Technology Data Exchange (ETDEWEB)

Guo, C.; Wells, P.S. [Suncor Energy, Fort McMurray, AB (Canada)

2010-07-01

This PowerPoint presentation discussed a pond assessment program conducted by Suncor to determine the properties of mature fine tailings (MFT) and composite tailings (CT) at reclaimed and unreclaimed sites. Mudline and sonar depth sounding techniques were used to determine solids contents. A wire line sampler provided point depth samples used for laboratory analyses. Continuous drill samples were obtained in order to characterize bottom fines and clay content. A flow penetration tests was used to determine the undrained shear strength of the soft tailings. A 3-D block model was then used to estimate soft material properties and to generate material distribution volumes and tonnages for different property ranges. The study showed that the block modelling techniques provide a more accurate tailings pond assessment than traditional approaches. While slow, ongoing static consolidation was observed, surface capping and artificial dewatering are required to provide trafficable ground for the final reclamation of the sites. tabs., figs.

Bioactive Compounds of Blueberries: Post-Harvest Factors Influencing the Nutritional Value of Products.

Science.gov (United States)

Michalska, Anna; Łysiak, Grzegorz

2015-08-10

Blueberries, besides having commonly-recognized taste properties, are also a valuable source of health-promoting bioactive compounds. For several decades, blueberries have gained in popularity all over the world, and recent years have seen not only an increase in fresh consumption, but also in the importance of blueberries for the processing industry. Blueberry processing mostly consists of freezing and juicing. Recently, more attention has been drawn to dewatering and drying, which are promising areas for developing novel blueberry products. Processing affects each biologically-active compound in a different way, and it is still unknown what changes those compounds undergo at the molecular level after the application of different processing technologies. This work presents the most recent state of knowledge about the pre-treatment and processing methods applied to blueberries and their influence on the content of biologically-active compounds. The presentation of methods is preceded by a brief overview of the characteristics of the blueberry species, a description of the chemical composition of the fruit and a short note about the main growing areas, production volumes and the management of fruit crops.

Influence of Fatty Acid Methyl Esters on Fuel properties of Biodiesel ...

African Journals Online (AJOL)

Influence of Fatty Acid Methyl Esters on Fuel properties of Biodiesel Produced from the. Seeds Oil of Curcubita ... Gas chromatograph coupled with mass spectrophotometer (GC-MS). The results indicate ..... Chemical and physical properties of ...

Model tests for corrosion influence of electrode surface on electroosmosis in marine sludge

Science.gov (United States)

Zheng, Lingwei; Li, Jinzhu; Shi, Hanru

2017-11-01

The corrosion of metal electrodes is inevitable on electroosmosis in soil. Surface corrosion of electrodes is also one of the reasons for increasing energy consumption in electroosmosis treatment. A series of laboratory tests were conducted employing three kinds of materials, aluminium, steel, and brass. To explore the impact of surface corrosion degree on electroosmosis, metal electrodes were pretreated with durations 0 h, 12 h, 24 h, and 36 h. After the pretreatment, corroded electrodes are used as anodes on electroosmosis. Water discharge, current, voltage potential were measured during the tests; water content was also tested at three points after the electroosmosis. The results showed that aluminium was better than steel in electroosmotic drainage while brass provided the worst dewatering performance. Surface corrosion did not influence the aluminium and steel on electroosmosis in marine sludge, but brass did. In the pretreatment of brass electrodes, corrosion rate had started to slow down at later periods, with the deterioration rate of dewatering reduced afterwards. As the results showed, it is not recommended to employ those easily deteriorated electrode materials from surface corrosion in practical engineering, such as brass; electrode material with higher electroosmosis exchange rate is recommended, such as aluminium.

Applicability of industrial wastewater as carbon source for denitrification of a sludge dewatering liquor.

Science.gov (United States)

Chen, Jiazhong; Lee, Yoomin; Oleszkiewicz, Jan A

2013-01-01

The applicability of four industrial waste streams from potato processing, canola processing and oil refining, biodiesel production (glycerol), and glycol as substitutes to methanol and ethanol in denitrification of anaerobically digested sludge dewatering liquor (centrate) was evaluated in bench-scale sequencing batch reactors. It was found that glycerol was the best substitute with the specific denitrification rate (SDNR) of 13 mg NO3-N/(g VSS x h) followed by potato processing wastewater at 12mg NO3-N/(g VSS x h). Both substrates produced faster SDNR than methanol's 10mg NO3-N/(g VSS x h); however, they were inferior to ethanol's 17 mg NO3-N/(g VSS x h). Glycol had SDNR of 8 mg NO3-N/(g VSS x h) and demonstrated a very fast acclimation rate, i.e. the response in increased denitrification rate was visible in three days following glycol addition. Canola processing and oil refining wastewater was considered an inappropriate carbon source due to a low SDNR of 5 mg NO3-N/(g VSS x h) and apparent inhibitory effect on nitrification.

Brown Coal Dewatering Using Poly (Acrylamide-Co-Potassium Acrylic Based Super Absorbent Polymers

Directory of Open Access Journals (Sweden)

Sheila Devasahayam

2015-09-01

Full Text Available With the rising cost of energy and fuel oils, clean coal technologies will continue to play an important role during the transition to a clean energy future. Victorian brown coals have high oxygen and moisture contents and hence low calorific value. This paper presents an alternative non evaporative drying technology for high moisture brown coals based on osmotic dewatering. This involves contacting and mixing brown coal with anionic super absorbent polymers (SAP which are highly crossed linked synthetic co-polymers based on a cross-linked copolymer of acryl amide and potassium acrylate. The paper focuses on evaluating the water absorption potential of SAP in contact with 61% moisture Loy Yang brown coal, under varying SAP dosages for different contact times and conditions. The amount of water present in Loy Yang coal was reduced by approximately 57% during four hours of SAP contact. The extent of SAP brown coal drying is directly proportional to the SAP/coal weight ratio. It is observed that moisture content of fine brown coal can readily be reduced from about 59% to 38% in four hours at a 20% SAP/coal ratio.

Effect of the social influence on topological properties of user-object bipartite networks

Science.gov (United States)

Liu, Jian-Guo; Hu, Zhaolong; Guo, Qiang

2013-11-01

Social influence plays an important role in analyzing online users' collective behaviors [Salganik et al., Science 311, 854 (2006)]. However, the effect of the social influence from the viewpoint of theoretical model is missing. In this paper, by taking into account the social influence and users' preferences, we develop a theoretical model to analyze the topological properties of user-object bipartite networks, including the degree distribution, average nearest neighbor degree and the bipartite clustering coefficient, as well as topological properties of the original user-object networks and their unipartite projections. According to the users' preferences and the global ranking effect, we analyze the theoretical results for two benchmark data sets, Amazon and Bookcrossing, which are approximately consistent with the empirical results. This work suggests that this model is feasible to analyze topological properties of bipartite networks in terms of the social influence and the users' preferences.

Influence of soil pedological properties on termite mound stability

OpenAIRE

Jouquet, Pascal; Guilleux, N.; Caner, L.; Chintakunta, S.; Ameline, M.; Shanbhag, R. R.

2016-01-01

This study investigated the influence of soil properties on the density and shape of epigeous fungus-growing termite nests in a dry deciduous forest in Karnataka, India. In this environment, Odontotermes obesus produces cathedral shaped mounds. Their density, shape (height and volume) and soil physicochemical properties were analyzed in ferralsol and vertisol environments. No significant difference was observed in O. obesus mound density (n = 2.7 mound ha(-1) on average in the vertisol and fe...

Earthworms facilitate the stabilization of pelletized dewatered sludge through shaping microbial biomass and activity and community.

Science.gov (United States)

Fu, Xiaoyong; Cui, Guangyu; Huang, Kui; Chen, Xuemin; Li, Fusheng; Zhang, Xiaoyu; Li, Fei

2016-03-01

In this study, the effect of earthworms on microbial features during vermicomposting of pelletized dewatered sludge (PDS) was investigated through comparing two degradation systems with and without earthworm E isenia fetida involvement. After 60 days of experimentation, a relatively stable product with low organic matter and high nitrate and phosphorous was harvested when the earthworms were involved. During the process, earthworms could enhance microbial activity and biomass at the initial stage and thus accelerating the rapid decomposition of PDS. The end products of vermicomposting allowed the lower values of bacterial and eukaryotic densities comparison with those of no earthworm addition. In addition, the presence of earthworms modified the bacterial and fungal diversity, making the disappearances of some pathogens and specific decomposing bacteria of recalcitrant substrates in the vermicomposting process. This study evidences that earthworms can facilitate the stabilization of PDS through modifying microbial activity and number and community during vermicomposting.

INFLUENCES OF SOIL PROPERTIES ON CHROMIUM (III SORPTION

Directory of Open Access Journals (Sweden)

R. Salmasi, F. Salmasi

2007-07-01

Full Text Available Soil adsorbing properties reduce sorption ability of the metal, which in turn may influence decision for remediation at contaminated sites. The objective of this study is presentation of a model based on soil properties to estimate the sorption of Cr(III in chromium contaminated soils. Twenty uncontaminated soil samples, with properties similar to the contaminated soils were selected from around of city of Tabriz and treated with Cr as CrCl3. A multiple regression analysis with statgraph software was used to drive an expression that related Cr sorption to common soil properties. The results showed that four soil properties were important in determining the amount of Cr adsorbed by the soils including pH, cation exchange capacity, total inorganic carbon and clay content with nearly 80% variability in Cr sorption and a reasonable level of confidence by this model. The obtained model suggested that Cr(III sorption was enhanced by higher soil pH, more total inorganic carbon, more clay, and higher cation exchange capacity.

Influence of Compacting Rate on the Properties of Compressed Earth Blocks

Directory of Open Access Journals (Sweden)

Humphrey Danso

2016-01-01

Full Text Available Compaction of blocks contributes significantly to the strength properties of compressed earth blocks. This paper investigates the influence of compacting rates on the properties of compressed earth blocks. Experiments were conducted to determine the density, compressive strength, splitting tensile strength, and erosion properties of compressed earth blocks produced with different rates of compacting speed. The study concludes that although the low rate of compaction achieved slightly better performance characteristics, there is no statistically significant difference between the soil blocks produced with low compacting rate and high compacting rate. The study demonstrates that there is not much influence on the properties of compressed earth blocks produced with low and high compacting rates. It was further found that there are strong linear correlations between the compressive strength test and density, and density and the erosion. However, a weak linear correlation was found between tensile strength and compressive strength, and tensile strength and density.

Influence of the structural properties on the pseudocritical magnetic behavior of single-wall ferromagnetic nanotubes

Energy Technology Data Exchange (ETDEWEB)

Salazar-Enriquez, C.D. [PCM Computational Applications, Universidad Nacional de Colombia - Sede Manizales, A.A. 127 Manizales (Colombia); Restrepo-Parra, E., E-mail: erestrepopa@unal.edu.co [PCM Computational Applications, Universidad Nacional de Colombia - Sede Manizales, A.A. 127 Manizales (Colombia); Restrepo, J. [Grupo de Magnetismo y Simulacion Gplus, Instituto de Fisica, Universidad de Antioquia, A.A. 1226 Medellin (Colombia)

2012-04-15

In this work we address the influence of the crystalline structure, concretely when the system under study is formed by square or hexagonal unit cells, upon the magnetic properties and pseudocritical behavior of single-wall ferromagnetic nanotubes. We focus not only on the effect of the geometrical shape of the unit cell but also on their dimensions. The model employed is based on the Monte Carlo method, the Metropolis dynamics and a nearest neighbors classical Heisenberg Hamiltonian. Magnetization per magnetic site, magnetic susceptibility, specific heat and magnetic energy were computed. These properties were computed varying the system size, unit cell dimension and temperature. The dependence of the nearest neighbor exchange integral on the nanotubes geometrical characteristics is also discussed. Results revealed a strong influence of the system topology on the magnetic properties caused by the difference in the coordination number between square and hexagonal unit cell. Moreover, the nanotubes diameter influence on magnetic properties is only observed at very low values, when the distance between atoms is less than it, presented by the 2D sheet. On the other hand, it was concluded that the surface-related finite-size effects do not influence the magnetic nanotubes properties, contrary to the case of other nano-systems as thin films and nanoparticles among others. - Highlights: Black-Right-Pointing-Pointer Unit cell geometry has strong influence on the magnetic properties in ferromagnetic nanotubes. Black-Right-Pointing-Pointer The nanotube diameter increase produces a decrease of interaction between nearest neighbor. Black-Right-Pointing-Pointer Surface-related finite-size effects do not influence the magnetic nanotubes properties.

Influence of the structural properties on the pseudocritical magnetic behavior of single-wall ferromagnetic nanotubes

International Nuclear Information System (INIS)

Salazar-Enríquez, C.D.; Restrepo-Parra, E.; Restrepo, J.

2012-01-01

In this work we address the influence of the crystalline structure, concretely when the system under study is formed by square or hexagonal unit cells, upon the magnetic properties and pseudocritical behavior of single-wall ferromagnetic nanotubes. We focus not only on the effect of the geometrical shape of the unit cell but also on their dimensions. The model employed is based on the Monte Carlo method, the Metropolis dynamics and a nearest neighbors classical Heisenberg Hamiltonian. Magnetization per magnetic site, magnetic susceptibility, specific heat and magnetic energy were computed. These properties were computed varying the system size, unit cell dimension and temperature. The dependence of the nearest neighbor exchange integral on the nanotubes geometrical characteristics is also discussed. Results revealed a strong influence of the system topology on the magnetic properties caused by the difference in the coordination number between square and hexagonal unit cell. Moreover, the nanotubes diameter influence on magnetic properties is only observed at very low values, when the distance between atoms is less than it, presented by the 2D sheet. On the other hand, it was concluded that the surface-related finite-size effects do not influence the magnetic nanotubes properties, contrary to the case of other nano-systems as thin films and nanoparticles among others. - Highlights: ► Unit cell geometry has strong influence on the magnetic properties in ferromagnetic nanotubes. ► The nanotube diameter increase produces a decrease of interaction between nearest neighbor. ► Surface-related finite-size effects do not influence the magnetic nanotubes properties.

THE INFLUENCE OF GAS-DENSITY AND LIQUID PROPERTIES ON BUBBLE BREAKUP

NARCIS (Netherlands)

WILKINSON, PM; VANSCHAYK, A; SPRONKEN, JPM; VANDIERENDONCK, LL

On the basis of a literature review of bubble breakup experiments, it is demonstrated that both liquid viscosity and surface tension have an influence on bubble stability and, thus, bubble breakup, for small as well as large bubbles. Possible influences of the gas properties on bubble breakup have

The influence of target properties on nuclear spectroscopy measurements

International Nuclear Information System (INIS)

Dionisio, J.S.; Vieu, C.; Lagrange, J.M.; Pautrat, M.; Vanhorenbeeck, J.; Passoja, A.

1988-01-01

A broad review of different kinds of in-beam nuclear spectroscopy measurements particularly influenced by the target properties is outlined. To illustrate such an influence a few typical examples of in-beam electron and gamma-ray spectroscopy measurements, performed at the Orsay MP Tandem accelerator, are reported. In particular several applications of the recoil ion catcher method in the study of short-lived nuclear isomers (with half-lives between ten and few hundred nanoseconds) are briefly described. This method is operated mostly with a pulsed heavy ion beam, bombarding a thin self-supported target but avoiding hitting the catcher foil. Moreover, the time of flight filtering properties of this experimental device is improved by a fast detection of compound nucleus deexcitation (performed with an array of several BaF 2 crystals). This kind of measurement shows clearly the importance of the target qualities as well as the need of good focusing properties and time structure for the accelerated particle beam. Finally, the required characteristics of the targets and recoil stopper foils needed for these measurements (and similar ones performed with the recoil ion shadow method) are analyzed in detail for a few typical experimental arrangements. (author). Abstract only

Influence of defects on diamond detection properties

International Nuclear Information System (INIS)

Tromson, Dominique

2000-01-01

This work focuses on the study of the influence of defects on the detection properties of diamond. Devices are fabricated using natural as well as synthetic diamond samples grown using the plasma enhanced chemical vapour deposition (CVD). Optical studies with infrared and Raman spectrometry are used to characterise the material properties as well as thermoluminescence and thermally stimulated current measurements. These thermally stimulated analyses reveal the presence of several trapping levels with emission temperatures below or near room temperature as well as an important level near 550 K. The influence of these defects on the alpha and X-ray detector responses is studied as a function of the initial state of the detectors (thermal treatment, irradiation) and of the measurement conditions (time, temperature). The results show a significant correlation between the charged state of traps, namely filled or empty and the response of the detectors. It appears that filling and emptying the traps respectively enhances the sensitivity and stability of detection devices to be used at room temperature and decreases the detection properties at higher temperature. Localised measurements are also used to study the spatial inhomogeneity of natural and CVD diamond samples from the 2D mapping of the detector responses. Non uniformity are attributed to a non-isotropic distribution of defects in natural diamonds. By comparing the detector responses to the topographical map of CVD samples a correlation appears between grains and grain boundaries with the variation of the detector sensitivity. Devices fabricated for detection applications with CVD samples are presented and namely for the monitoring and profiling of synchrotron beams as well as dose rate measurements in harsh environments. (author) [fr

The factors influencing microstructure and mechanical properties of ADI

Directory of Open Access Journals (Sweden)

A. Vaško

2009-01-01

Full Text Available The paper deals with the influence of different conditions of isothermal heat treatment on microstructure and mechanical properties of austempered ductile iron (ADI. Different temperature of isothermal transformation of austenite and different holding time at this temperature were used for heat treatment of specimens. The microstructure of specimens after casting and after heat treatment was evaluated by STN EN ISO 945 and by image analysis (using Lucia software. Mechanical properties were evaluated by the tensile test, the Rockwell hardness test and fatigue tests.

A study on the treatment of radioactive slurry liquid waste

International Nuclear Information System (INIS)

Jeong, Gyeong Hwan; Chung, U. S.; Baik, S. T.; Park, S. K.; Moon, J.S.; Jung, K.J.

1998-12-01

The influence of anionic flocculants on the dewatering of radioactive slurries has been investigated in a laboratory-scale vacuum filtration unit. Simultaneously the influence of certain surfactants on the dewatering of radioactive slurries with anionic flocculants has also been investigated. Test results show that the flocculated filter cake generally contains higher residual water than the unflocculated cake. The non-ionic surfactant Triton X-100 was effective in reducing the moisture content of the cake

A study on the treatment of radioactive slurry liquid waste

Energy Technology Data Exchange (ETDEWEB)

Jeong, Gyeong Hwan; Chung, U. S.; Baik, S. T.; Park, S. K.; Moon, J.S.; Jung, K.J

1998-12-01

The influence of anionic flocculants on the dewatering of radioactive slurries has been investigated in a laboratory-scale vacuum filtration unit. Simultaneously the influence of certain surfactants on the dewatering of radioactive slurries with anionic flocculants has also been investigated. Test results show that the flocculated filter cake generally contains higher residual water than the unflocculated cake. The non-ionic surfactant Triton X-100 was effective in reducing the moisture content of the cake.

Comparative evaluation of microbial and chemical leaching processes for heavy metal removal from dewatered metal plating sludge

International Nuclear Information System (INIS)

Bayat, Belgin; Sari, Bulent

2010-01-01

The purpose of the study described in this paper was to evaluate the application of bioleaching technique involving Acidithiobacillus ferrooxidans to recover heavy metals (Zn, Cu, Ni, Pb, Cd and Cr) in dewatered metal plating sludge (with no sulfide or sulfate compounds). The effect of some conditional parameters (i.e. pH, oxidation-reduction potential (ORP), sulfate production) and operational parameters (i.e. pulp density of the sludge and agitation time) were investigated in a 3 l completely mixed batch (CMB) reactor. The metal recovery yields in bioleaching were also compared with chemical leaching of the sludge waste using commercial inorganic acids (sulfuric acids and ferric chloride). The leaching of heavy metals increased with decreasing of pH and increasing of ORP and sulfate production during the bioleaching experiment. Optimum pulp density for bioleaching was observed at 2% (w/v), and leaching efficiency decreased with increasing pulp density in bioleaching experiments. Maximum metal solubilization (97% of Zn, 96% of Cu, 93% of Ni, 84% of Pb, 67% of Cd and 34% of Cr) was achieved at pH 2, solids contents of 2% (w/v), and a reaction temperature of 25 ± 2 deg. C during the bioleaching process. The maximum removal efficiencies of 72% and 79% Zn, 70% and 75% Cu, 69% and 73% Ni, 57% and 70% Pb, 55% and 65% Cd, and 11% and 22% Cr were also attained with the chemical leaching using sulfuric acids and ferric chloride, respectively, at pH 2, solids contents of 2% (w/v), and a reaction temperature of 25 ± 2 deg. C during the acid leaching processes. The rates of metal leaching for bioleaching and chemical leaching are well described by a kinetic equation related to time. Although bioleaching generally requires a longer period of operation compared to chemical leaching, it achieves higher removal efficiency for heavy metals. The efficiency of leaching processes can be arranged in descending order as follows: bioleaching > ferric chloride leaching > sulfuric acid

Comparative evaluation of microbial and chemical leaching processes for heavy metal removal from dewatered metal plating sludge

Energy Technology Data Exchange (ETDEWEB)

Bayat, Belgin, E-mail: bbayat@cu.edu.tr [Department of Environmental Engineering, Faculty of Engineering and Architecture, Cukurova University, Balcali, Adana 01330 (Turkey); Sari, Bulent [Department of Environmental Engineering, Faculty of Engineering and Architecture, Cukurova University, Balcali, Adana 01330 (Turkey)

2010-02-15

The purpose of the study described in this paper was to evaluate the application of bioleaching technique involving Acidithiobacillus ferrooxidans to recover heavy metals (Zn, Cu, Ni, Pb, Cd and Cr) in dewatered metal plating sludge (with no sulfide or sulfate compounds). The effect of some conditional parameters (i.e. pH, oxidation-reduction potential (ORP), sulfate production) and operational parameters (i.e. pulp density of the sludge and agitation time) were investigated in a 3 l completely mixed batch (CMB) reactor. The metal recovery yields in bioleaching were also compared with chemical leaching of the sludge waste using commercial inorganic acids (sulfuric acids and ferric chloride). The leaching of heavy metals increased with decreasing of pH and increasing of ORP and sulfate production during the bioleaching experiment. Optimum pulp density for bioleaching was observed at 2% (w/v), and leaching efficiency decreased with increasing pulp density in bioleaching experiments. Maximum metal solubilization (97% of Zn, 96% of Cu, 93% of Ni, 84% of Pb, 67% of Cd and 34% of Cr) was achieved at pH 2, solids contents of 2% (w/v), and a reaction temperature of 25 {+-} 2 deg. C during the bioleaching process. The maximum removal efficiencies of 72% and 79% Zn, 70% and 75% Cu, 69% and 73% Ni, 57% and 70% Pb, 55% and 65% Cd, and 11% and 22% Cr were also attained with the chemical leaching using sulfuric acids and ferric chloride, respectively, at pH 2, solids contents of 2% (w/v), and a reaction temperature of 25 {+-} 2 deg. C during the acid leaching processes. The rates of metal leaching for bioleaching and chemical leaching are well described by a kinetic equation related to time. Although bioleaching generally requires a longer period of operation compared to chemical leaching, it achieves higher removal efficiency for heavy metals. The efficiency of leaching processes can be arranged in descending order as follows: bioleaching > ferric chloride leaching > sulfuric

Bioactive Compounds of Blueberries: Post-Harvest Factors Influencing the Nutritional Value of Products

Directory of Open Access Journals (Sweden)

Anna Michalska

2015-08-01

Full Text Available Blueberries, besides having commonly-recognized taste properties, are also a valuable source of health-promoting bioactive compounds. For several decades, blueberries have gained in popularity all over the world, and recent years have seen not only an increase in fresh consumption, but also in the importance of blueberries for the processing industry. Blueberry processing mostly consists of freezing and juicing. Recently, more attention has been drawn to dewatering and drying, which are promising areas for developing novel blueberry products. Processing affects each biologically-active compound in a different way, and it is still unknown what changes those compounds undergo at the molecular level after the application of different processing technologies. This work presents the most recent state of knowledge about the pre-treatment and processing methods applied to blueberries and their influence on the content of biologically-active compounds. The presentation of methods is preceded by a brief overview of the characteristics of the blueberry species, a description of the chemical composition of the fruit and a short note about the main growing areas, production volumes and the management of fruit crops.

Bioactive Compounds of Blueberries: Post-Harvest Factors Influencing the Nutritional Value of Products

Science.gov (United States)

Michalska, Anna; Łysiak, Grzegorz

2015-01-01

Blueberries, besides having commonly-recognized taste properties, are also a valuable source of health-promoting bioactive compounds. For several decades, blueberries have gained in popularity all over the world, and recent years have seen not only an increase in fresh consumption, but also in the importance of blueberries for the processing industry. Blueberry processing mostly consists of freezing and juicing. Recently, more attention has been drawn to dewatering and drying, which are promising areas for developing novel blueberry products. Processing affects each biologically-active compound in a different way, and it is still unknown what changes those compounds undergo at the molecular level after the application of different processing technologies. This work presents the most recent state of knowledge about the pre-treatment and processing methods applied to blueberries and their influence on the content of biologically-active compounds. The presentation of methods is preceded by a brief overview of the characteristics of the blueberry species, a description of the chemical composition of the fruit and a short note about the main growing areas, production volumes and the management of fruit crops. PMID:26266408

On the influence of tyre and structural properties on the stability of bicycles

Science.gov (United States)

Doria, Alberto; Roa Melo, Sergio Daniel

2018-06-01

In recent years the Whipple Carvallo Bicycle Model has been extended to analyse high speed stability of bicycles. Various researchers have developed models taking into account the effects of front frame compliance and tyre properties, nonetheless, a systematic analysis has not been yet carried out. This paper aims at analysing parametrically the influence of front frame compliance and tyre properties on the open loop stability of bicycles. Some indexes based on the eigenvalues of the dynamic system are defined to evaluate quantitatively bicycle stability. The parametric analysis is carried out with a factorial design approach to determine the most influential parameters. A commuting and a racing bicycle are considered and numerical results show different effects of the various parameters on each bicycle. In the commuting bicycle, the tyre properties have greater influence than front frame compliance, and the weave mode has the main effect on stability. Conversely, in the racing bicycle, the front frame compliance parameters have greater influence than tyre properties, and the wobble mode has the main effect on stability.

Effect of Long-Term Freezing and Freeze–Thaw Cycles on Indigenous and Inoculated Microorganisms in Dewatered Blackwater

DEFF Research Database (Denmark)

Gunnarsdottir, Ragnhildur; Müller, Karoline; Jensen, Pernille Erland

2012-01-01

Wastewater treatment in many Arctic regions is inadequate, even nonexisting. Natural freezing of wastewater in those areas may be beneficial for reduction of microorganisms. The aim of this study was to investigate the effect of long-term freezing, and repeated freezing and thawing, on indigenous...... coliforms, fecal streptococci, and antibiotic-resistant (AR) bacteria, and inoculated Salmonella Enteriditis and E. coli bacteriophage ΦX174 in dewatered blackwater. At the end of the long-term freezing experiment (10 months), an MPN recovery study was done, including the microbial groups that had shown...... the largest reduction, using tryptone soy broth at incubation temperatures of 10 and 20 °C overnight for the coliforms and AR bacteria, and buffered peptone water at incubation temperature of 37 °C for 18–20 h for Salmonella. Fecal streptococci were more resistant to long-term freezing than the coliform group...

Influence of ionizing radiation and use of plasticizers on the mechanical properties and barrier properties of biodegradable films

International Nuclear Information System (INIS)

Ponce, Patricia; Parra, Duclerc F.; Carr, Laura G.; Sato, Juliana S.; Lugao, Ademar B.

2005-01-01

This work reports the influence of radiation and plasticizers on the barrier properties [water vapour permeability (WVP)] and mechanical properties (tensile strength and elongation) of edible films made of starch. These films were prepared with 4 g of starch/100 mL of water; 2-10 g polyethylene glycol (PEG)/100 g starch; and at natural pH. Tensile strength and percentage elongation were measured using a Mechanical Universal Testing Machine Instron 4400R and the water vapour permeability was determined according to ASTM E96-80 (ASTM, 1989). The mechanical properties of starch films are influenced by the plasticizer concentration. An increase in PEG content showed a considerable increase in elongation percentage and a decrease in the tensile strength of the films, also increase the permeability of the films in water. After irradiation, the barrier properties [water vapour permeability (WVP)] and mechanical properties (tensile strength and elongation) of the films were improved due to chemical reactions among polymer molecules. The films were irradiated at room temperature with gamma radiation. Irradiated starch cassava films with polyethylene glycol (PEG) as plasticizer have good flexibility and low water permeability, which indicate potential application as edible films (author)

Sensory properties of marinated herring ( Clupea harengus ) - influence of fishing ground and season

DEFF Research Database (Denmark)

Nielsen, Durita; Hyldig, Grethe; Nielsen, Henrik Hauch

2004-01-01

fillets. Fishing ground did not influence the odor, flavor or texture, but there was an apparent effect of season on the sensory profile. The sensory properties were influenced by body weight, but not by age, sex and gonad maturity. The influence of varying lipid content, water content and liquid holding...

Influence of nanoclay on properties of HDPE/wood composites

Science.gov (United States)

Yong Lei; Qinglin Wu; Craig M. Clemons; Fei Yao; Yanjun Xu

2007-01-01

Composites based on high density polyethylene (HDPE), pine flour, and organic clay were made by melt compounding and then injection molding. The influence of clay on crystallization behavior, mechanical properties, water absorption, and thermal stability of HDPE/pine composites was investigated. The HDPE/pine composites containing exfoliated clay were made by a two-...

Dissipation of triclosan, triclocarban, carbamazepine and naproxen in agricultural soil following surface or sub-surface application of dewatered municipal biosolids

Energy Technology Data Exchange (ETDEWEB)

Al-Rajab, Abdul Jabbar; Sabourin, Lyne [Agriculture and Agri-Food Canada, London, ON N5V 4T3 (Canada); Lapen, David R. [Agriculture and Agri-Food Canada, Ottawa, ON K1A 0C6 (Canada); Topp, Edward, E-mail: ed.topp@agr.gc.ca [Agriculture and Agri-Food Canada, London, ON N5V 4T3 (Canada); Department of Biology, Western University, London, ON N6A 5B7 (Canada)

2015-04-15

In many jurisdictions land application of municipal biosolids is a valued source of nutrients for crop production. The practice must be managed to ensure that crops and adjacent water are not subject to contamination by pharmaceuticals or other organic contaminants. The broad spectrum antimicrobial agents triclosan (TCS) and triclocarban (TCC), the anti-epileptic drug carbamazepine (CBZ), and the nonsteroidal anti-inflammatory drug naproxen (NAP) are widely used and are carried in biosolids. In the present study, the effect of biosolids and depth of placement in the soil profile on the rates of TCS, TCC, CBZ, and NAP dissipation were evaluated under semi-field conditions. Aggregates of dewatered municipal biosolids (DMBs) supplemented with {sup 14}C-labeled residues were applied either on the soil surface or in the subsurface of the soil profile, and incubated over several months under ambient outdoor conditions. The dissipation of TCS, TCC and NAP was significantly faster in sub-surface than surface applied biosolid aggregates. In contrast the dissipation rate for CBZ was the same in surface applied and incorporated aggregates. Overall, the present study has determined a significant effect of depth of placement on the dissipation rate of biodegradable molecules. - Highlights: • We characterized the soil fate of four organic contaminants carried in biosolids. • Biosolids were placed on the soil surface or incorporated within the soil profile. • Naproxen, triclosan and triclocarban were dissipated more rapidly when incorporated. • Depth of placement did not influence the rate of carbamazepine dissipation. • Soil incorporation of biosolids will result in more rapid dissipation of contaminants.

Dissipation of triclosan, triclocarban, carbamazepine and naproxen in agricultural soil following surface or sub-surface application of dewatered municipal biosolids

International Nuclear Information System (INIS)

Al-Rajab, Abdul Jabbar; Sabourin, Lyne; Lapen, David R.; Topp, Edward

2015-01-01

In many jurisdictions land application of municipal biosolids is a valued source of nutrients for crop production. The practice must be managed to ensure that crops and adjacent water are not subject to contamination by pharmaceuticals or other organic contaminants. The broad spectrum antimicrobial agents triclosan (TCS) and triclocarban (TCC), the anti-epileptic drug carbamazepine (CBZ), and the nonsteroidal anti-inflammatory drug naproxen (NAP) are widely used and are carried in biosolids. In the present study, the effect of biosolids and depth of placement in the soil profile on the rates of TCS, TCC, CBZ, and NAP dissipation were evaluated under semi-field conditions. Aggregates of dewatered municipal biosolids (DMBs) supplemented with 14 C-labeled residues were applied either on the soil surface or in the subsurface of the soil profile, and incubated over several months under ambient outdoor conditions. The dissipation of TCS, TCC and NAP was significantly faster in sub-surface than surface applied biosolid aggregates. In contrast the dissipation rate for CBZ was the same in surface applied and incorporated aggregates. Overall, the present study has determined a significant effect of depth of placement on the dissipation rate of biodegradable molecules. - Highlights: • We characterized the soil fate of four organic contaminants carried in biosolids. • Biosolids were placed on the soil surface or incorporated within the soil profile. • Naproxen, triclosan and triclocarban were dissipated more rapidly when incorporated. • Depth of placement did not influence the rate of carbamazepine dissipation. • Soil incorporation of biosolids will result in more rapid dissipation of contaminants

Influence of cure activator on the structure and properties of rubbers

Directory of Open Access Journals (Sweden)

O. V. Karmanova

2013-01-01

Full Text Available The influence of vulcanization activator type on the properties of the compositions and elastic-strength characteristics of rubber was studied. Found that the modification of zinc oxide as the basis of actual formation curing vulcanization agents leads to an increase of vulcanization active centers, providing an increase in the velocity of rubber vulcanization and improvement of physical and mechanical rubber’s properties.

The influence of radiation on bacterial cells and their proteolytic properties

International Nuclear Information System (INIS)

Szulc, M.; Stefaniakowa, A.; Stanczak, B.; Peconek, J.

1980-01-01

The suspension of bacterial cells and their spores were exposed to X rays in the environment with and without protein. The doses of radiation ranged from 1 to 100 Gy and in case of spores of B. subtilis from 50 to 1000 Gy. It was found that irradiation to Proteus vulgaris, Pseudomonas fluorescens and Ps. aeruginosa caused an inconsiderable decrease of proteolytic properties of the generation originated from irradiated bacteria. Irradiation of B. subtilis spores did not influence the proteolytic activity of bacterial cells derived from the exposed spores. The degree of wasting away of bacteria exposed to the same radiation was higher than the rate of proteolytic properties decrease. The presence of protein in the surroundings had no influence on proteolytic characteristics of new generations. (author)

Influence of membrane properties on fouling in submerged membrane bioreactors

NARCIS (Netherlands)

van der Marel, P.; Zwijnenburg, A.; Kemperman, Antonius J.B.; Wessling, Matthias; Temmink, Hardy; van der Meer, Walterus Gijsbertus Joseph

2010-01-01

Polymeric flat-sheet membranes with different properties were used in filtration experiments with activated sludge from a pilot-scale MBR to investigate the influence of membrane pore size, surface porosity, pore morphology, and hydrophobicity on membrane fouling. An improved flux-step method was

Influence of the Reclaim Addition on Properties of Moulding Sands with the Geopol Binder

Directory of Open Access Journals (Sweden)

Drożyński D.

2015-03-01

Full Text Available The investigation results of the influence of the reclaim additions on the properties of moulding sands with the GEOPOL geopolymer binder developed by the SAND TEAM Company were presented. Two brands of hardeners were applied in the tested compositions, the first one was developed by the SAND TEAM Company, marked SA72 and the new hardener offered by the KRATOS Company, marked KR72. The main purpose of investigations was to determine the influence of reclaim fractions and the applied hardener on the basic moulding sands properties, such as: bending and tensile strength, permeability and grindability. The unfavourable influence of the reclaim additions into moulding sands on the tested properties as well as an increased hardening rate, were found. Moulding sands, in which the hardener KR72 of the KRATOS Company was used, were less sensitive to the reclaim additions

Influence of organic and inorganic flocculants on the formation of PCDD/Fs during sewage sludge incineration.

Science.gov (United States)

Lin, Xiaoqing; Li, Xiaodong; Lu, Shengyong; Wang, Fei; Chen, Tong; Yan, Jianhua

2015-10-01

Flocculants are widely used to improve the properties of sludge dewatering in industrial wastewater treatment. However, there have been no studies conducted on the influence of flocculants on the formation of polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs) during sewage sludge incineration. This paper selected three typical kinds of flocculants, including polyacrylamide (PAM), poly-ferric chloride (PFC), and polyaluminum chloride (PAC) flocculant, to study their influences on the formation of PCDD/Fs during sewage sludge incineration. The results indicated that PAM flocculant, which is an organic flocculant, inhibited the formation of PCDD/Fs in sewage sludge incineration, while inorganic flocculant, such as PFC and PAC flocculant, promoted the formation. The most probable explanation is that the amino content in the PAM flocculant acted as an inhibitor in the formation of PCDD/Fs, while the chlorine content, especially the metal catalyst in the PFC and PAC flocculants, increased the formation rate. The addition of flocculants nearly did not change the distribution of PCDD/F homologues. The PCDFs contributed the most toxic equivalent (TEQ) value, especially 2, 3, 4, 7, 8-PeCDF. Therefore, the use of inorganic flocculants in industrial wastewater treatment should be further assessed and possibly needs to be strictly regulated if the sludge is incinerated. From this aspect, a priority to the use of organic flocculants should be given.

Design and construction of solidification and dewatering facility at Alabama Power Company's Farley Nuclear Plant

International Nuclear Information System (INIS)

Farnsworth, P.

1988-01-01

The approximate total cost of the structure and supporting piping systems is estimated to be 4.1 million dollars. Total dose savings per year could be as high as 70 man Rem for resin processing alone. The ability to store refueling equipment, process contaminated oils, load and unload trucks and containers regardless of weather conditions and support repair work on equipment greatly enhances the cost effectiveness of the project. It will take at least one year of operation of the facility to accurately assess the true cost savings to Alabama Power Company. The morale factor for the Waste and Decon Group has escalated measurably due to the dose reduction to our personnel. Plant and company management are well pleased due to the possibility of a spill or release to the environment has been eliminated which was on intangible cost. Facility construction has been completed as of this date and resin transfer anticipated within the next few days. Some of the problems encountered in planning and constructing this solidification and dewatering facility are presented. A safety evaluation for the facility is included in the appendix

Optimization of volatile fatty acid production with co-substrate of food wastes and dewatered excess sludge using response surface methodology.

Science.gov (United States)

Hong, Chen; Haiyun, Wu

2010-07-01

Central-composite design (CCD) and response surface methodology (RSM) were used to optimize the parameters of volatile fatty acid (VFA) production from food wastes and dewatered excess sludge in a semi-continuous process. The effects of four variables (food wastes composition in the co-substrate of food wastes and excess sludge, hydraulic retention time (HRT), organic loading rate (OLR), and pH) on acidogenesis were evaluated individually and interactively. The optimum condition derived via RSM was food wastes composition, 88.03%; HRT, 8.92 days; OLR, 8.31 g VSS/ld; and pH 6.99. The experimental VFA concentration was 29,099 mg/l under this optimum condition, which was well in agreement with the predicted value of 28,000 mg/l. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

INFLUENCE OF WINE ACID ON RHEOLOGICAL PROPERTIES OF WELL BORE CEMENT SLURRIES AND HARDENED CEMENT PROPERTIES

Directory of Open Access Journals (Sweden)

Nediljka Gaurina-Međimurec

1989-12-01

Full Text Available Adaptation of commercial types of domestic cements for use in cementing the deep wells is a process by which Yugoslav oil industry tends to solve problems of completion of those wells independently. In order to design a domestic, cheep and effective retarder, tests of applicability of wine acid on cement slurries have been carried out. Besides examining the necessary wine acid content to achieve desirable Theological properties, the influence of this additive on properties of hardened cement samples has been tested too (the paper is published in Croatian.

Influence of surface roughness on the friction property of textured surface

OpenAIRE

Yuankai Zhou; Hua Zhu; Wenqian Zhang; Xue Zuo; Yan Li; Jianhua Yang

2015-01-01

In contrast with dimple textures, surface roughness is a texture at the micro-scale, essentially which will influence the load-bearing capacity of lubricant film. The numerical simulation was carried out to investigate the influence of surface roughness on friction property of textured surface. The lubricant film pressure was obtained using the method of computational fluid dynamics according to geometric model of round dimple, and the renormalization-group k–ε turbulent model was adopted in ...

Feasibility of vermicomposting dewatered sludge from paper mills using Perionyx excavatus

Directory of Open Access Journals (Sweden)

Puspanjali Sonowal

2013-06-01

Full Text Available India has a large network of pulp and paper mills of varying capacity. On an industrial scale the sludge from paper and pulp mills is disposed of either as landfill or incinerated. Both methods result in the loss of a valuable resource and have obvious environmental and economic disadvantages. The solid waste from pulp and paper mills is a source of organic matter and its proper disposal and management is the responsibility of the industry. As composting/vermicomposting could be used to transform this waste trials were carried out to determine the feasibility of converting dewatered sludge (DS into a value added end product using an earthworm, Perionyx excavatus. The vermicomposting of the waste resulted in an increase in its electrical conductivity (EC, ash content, total nitrogen (TN, total phosphorous (TP and available phosphorous (AP, respectively, and a decrease in total organic carbon (TOC, biochemical oxygen demand (BOD, chemical oxygen demand (COD, oxygen uptake rate (OUR and evolution of carbon dioxide (CO2. Overall, the best treatment was T5 in which there was a 76.1% increase in TP, 58.7% in TN, 74.5% decrease in TOC , and a reduction of 6.7 fold in the production of CO2 and 10.7 fold in BOD, respectively. Our trials demonstrate that vermicomposting using an epigeic earthworm, Perionyx excavatus, is an alternate and environmentally safe way of recycling paper mill sludge if it is mixed with an appropriate amount of cow dung and food processing waste. Overall T5 was the best combination of paper mill sludge and waste for vermicomposting followed by T3, T2, T4 and T1, respectively.

Insights on the Optical Properties of Estuarine DOM - Hydrological and Biological Influences.

Directory of Open Access Journals (Sweden)

Luísa Santos

Full Text Available Dissolved organic matter (DOM in estuaries derives from a diverse array of both allochthonous and autochthonous sources. In the estuarine system Ria de Aveiro (Portugal, the seasonality and the sources of the fraction of DOM that absorbs light (CDOM were inferred using its optical and fluorescence properties. CDOM parameters known to be affected by aromaticity and molecular weight were correlated with physical, chemical and meteorological parameters. Two sites, representative of the marine and brackish water zones of the estuary, and with different hydrological characteristics, were regularly surveyed along two years, in order to determine the major influences on CDOM properties. Terrestrial-derived compounds are the predominant source of CDOM in the estuary during almost all the year and the two estuarine zones presented distinct amounts, as well as absorbance and fluorescence characteristics. Freshwater inputs have major influence on the dynamics of CDOM in the estuary, in particular at the brackish water zone, where accounted for approximately 60% of CDOM variability. With a lower magnitude, the biological productivity also impacted the optical properties of CDOM, explaining about 15% of its variability. Therefore, climate changes related to seasonal and inter-annual variations of the precipitation amounts might impact the dynamics of CDOM significantly, influencing its photochemistry and the microbiological activities in estuarine systems.

Insights on the Optical Properties of Estuarine DOM - Hydrological and Biological Influences.

Science.gov (United States)

Santos, Luísa; Pinto, António; Filipe, Olga; Cunha, Ângela; Santos, Eduarda B H; Almeida, Adelaide

2016-01-01

Dissolved organic matter (DOM) in estuaries derives from a diverse array of both allochthonous and autochthonous sources. In the estuarine system Ria de Aveiro (Portugal), the seasonality and the sources of the fraction of DOM that absorbs light (CDOM) were inferred using its optical and fluorescence properties. CDOM parameters known to be affected by aromaticity and molecular weight were correlated with physical, chemical and meteorological parameters. Two sites, representative of the marine and brackish water zones of the estuary, and with different hydrological characteristics, were regularly surveyed along two years, in order to determine the major influences on CDOM properties. Terrestrial-derived compounds are the predominant source of CDOM in the estuary during almost all the year and the two estuarine zones presented distinct amounts, as well as absorbance and fluorescence characteristics. Freshwater inputs have major influence on the dynamics of CDOM in the estuary, in particular at the brackish water zone, where accounted for approximately 60% of CDOM variability. With a lower magnitude, the biological productivity also impacted the optical properties of CDOM, explaining about 15% of its variability. Therefore, climate changes related to seasonal and inter-annual variations of the precipitation amounts might impact the dynamics of CDOM significantly, influencing its photochemistry and the microbiological activities in estuarine systems.

Influence of succinylation on physicochemical property of yak casein micelles.

Science.gov (United States)

Yang, Min; Yang, Jitao; Zhang, Yuan; Zhang, Weibing

2016-01-01

Succinylation is a chemical-modification method that affects the physicochemical characteristics and functional properties of proteins. This study assessed the influence of succinylation on the physicochemical properties of yak casein micelles. The results revealed that surface hydrophobicity indices decreased with succinylation. Additionally, denaturation temperature and denaturation enthalpy decreased with increasing succinylation level, except at 82%. The buffering properties of yak casein micelles were affected by succinylation. It was found that chemical modification contributed to a slight shift of the buffering peak towards a lower pH value and a markedly increase of the maximum buffering values of yak casein micelles at pH 4.5-6.0 and pH casein micellar hydration and whiteness values. The findings obtained from this study will provide the basic information on the physicochemical properties of native and succinylated yak casein micelles. Copyright © 2015 Elsevier Ltd. All rights reserved.

Feedback of land subsidence on the movement and conjunctive use of water resources

Science.gov (United States)

Schmid, Wolfgang; Hanson, Randall T.; Leake, Stanley A.; Hughes, Joseph D.; Niswonger, Richard G.

2014-01-01

The dependency of surface- or groundwater flows and aquifer hydraulic properties on dewatering-induced layer deformation is not available in the USGS's groundwater model MODFLOW. A new integrated hydrologic model, MODFLOW-OWHM, formulates this dependency by coupling mesh deformation with aquifer transmissivity and storage and by linking land subsidence/uplift with deformation-dependent flows that also depend on aquifer head and other flow terms. In a test example, flows most affected were stream seepage and evapotranspiration from groundwater (ETgw). Deformation feedback also had an indirect effect on conjunctive surface- and groundwater use components: Changed stream seepage and streamflows influenced surface-water deliveries and returnflows. Changed ETgw affected irrigation demand, which jointly with altered surface-water supplies resulted in changed supplemental groundwater requirements and pumping and changed return runoff. This modeling feature will improve the impact assessment of dewatering-induced land subsidence/uplift (following irrigation pumping or coal-seam gas extraction) on surface receptors, inter-basin transfers, and surface-infrastructure integrity.

Anion influence on thermophysical properties of ionic liquids: 1-butylpyridinium tetrafluoroborate and 1-butylpyridinium triflate.

Science.gov (United States)

Bandrés, Isabel; Royo, Félix M; Gascón, Ignacio; Castro, Miguel; Lafuente, Carlos

2010-03-18

The thermophysical properties of two pyridinium-based ionic liquids, 1-butylpyridinium tetrafluoroborate and 1-butylpyridinium triflate, have been measured. Thus, densities, refractive indices, speeds of sound, viscosities, surface tensions, isobaric molar heat capacities, and thermal properties have been experimentally determined over a wide range of temperatures. The comparison of the properties of the two ionic liquids has allowed us to analyze in detail the anion influence. Moreover, useful derived properties have been calculated from the results. On the other hand, the influence of the lack of a substituent in the cation has been evaluated when properties of 1-butylpyridinium tetrafluoroborate have been contrasted to those of 1-butyl-n-methylpyridinium tetrafluoroborate, (n = 2, 3, or 4). The study has been carried out paying special attention to interactions between ions in order to elucidate the desired relationship between properties and structural characteristics of ionic liquids.

Extracellular polymeric substances (EPS) producing bacterial strains of municipal wastewater sludge: isolation, molecular identification, EPS characterization and performance for sludge settling and dewatering.

Science.gov (United States)

Bala Subramanian, S; Yan, S; Tyagi, R D; Surampalli, R Y

2010-04-01

Wastewater treatment plants often face the problems of sludge settling mainly due to sludge bulking. Generally, synthetic organic polymer and/or inorganic coagulants (ferric chloride, alum and quick lime) are used for sludge settling. These chemicals are very expensive and further pollute the environment. Whereas, the bioflocculants are environment friendly and may be used to flocculate the sludge. Extracellular polymeric substances (EPS) produced by sludge microorganisms play a definite role in sludge flocculation. In this study, 25 EPS producing strains were isolated from municipal wastewater treatment plant. Microorganisms were selected based on EPS production properties on solid agar medium. Three types of EPS (slime, capsular and bacterial broth mixture of both slime and capsular) were harvested and their characteristics were studied. EPS concentration (dry weight), viscosity and their charge (using a Zetaphoremeter) were also measured. Bioflocculability of obtained EPS was evaluated by measuring the kaolin clay flocculation activity. Six bacterial strains (BS2, BS8, BS9, BS11, BS15 and BS25) were selected based on the kaolin clay flocculation. The slime EPS was better for bioflocculation than capsular EPS and bacterial broth. Therefore, extracted slime EPS (partially purified) from six bacterial strains was studied in terms of sludge settling [sludge volume index (SVI)] and dewatering [capillary suction time (CST)]. Biopolymers produced by individual strains substantially improved dewaterability. The extracted slime EPS from six different strains were partially characterized. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Recovery, restoration, and development of an enhancement plan for the Leading Creek watershed after dewatering of the Meigs number-sign 31 coal mine in Ohio

International Nuclear Information System (INIS)

Cherry, D.S.; Hassel, J.H. Van; Yeager, M.M.; Babendreier, J.E.; Currie, R.J.; Astin, L.E.; Lynde, S.R.

1995-01-01

Following the flooding of the Meigs number-sign 31 deep coal mine in Meigs County, Ohio, a proactive plan was developed to evaluate effects of initial dewatering, recovery, and development of a watershed enhancement plan. Approximately half of the 31-mile Leading Creek mainstem received coal mine discharge of high conductivity, low pH, high metals and total suspended solids loading. Most forms of aquatic life were depleted in the impacted areas of the creek. After three years since the incident, many forms of benthic macroinvertebrates and fish have returned to the creek, and sediments have been purged of metal loading by storm water events. The enhancement plan involves a reconnaissance of the creek and tributaries pinpointing areas of agricultural sedimentation and abandoned mined land (AML) influences in the lower half. Research activities involved sampling water and sediment in 10 stations of the creek and 17 major tributaries. The tributaries were addressed as point source discharges with water/sediment toxicity testing conducted. In-situ testing included growth impairment evaluation of Asian clams at 27 stations in the watershed. Several tributaries were intermittently toxic depending upon rainfall and the degree of AML input. Benthic macroinvertebrate assembles in most tributaries were stressed and comprised 0--3 taxa. Erosion/sedimentation loading was being addressed by hydrological modeling of the creek, land use management/habitat assessment, and data management by geographic information systems

influence of the substitution on the electronic properties of perylene ...

African Journals Online (AJOL)

Preferred Customer

The higher performance found in single crystal OFETs compared to thin-film. OFETs is related to the high ... Influence of substitution on electronic properties of perylene-3,4:9,10-bis(dicarboximides). Bull. Chem. Soc. .... be good n-type materials for OFETs due to the efficient electron injection from common gold electrode, ca.

Environmental and management influences on temporal variability of near saturated soil hydraulic properties.

Science.gov (United States)

Bodner, G; Scholl, P; Loiskandl, W; Kaul, H-P

2013-08-01

Structural porosity is a decisive property for soil productivity and soil environmental functions. Hydraulic properties in the structural range vary over time in response to management and environmental influences. Although this is widely recognized, there are few field studies that determine dominant driving forces underlying hydraulic property dynamics. During a three year field experiment we measured temporal variability of soil hydraulic properties by tension infiltrometry. Soil properties were characterized by hydraulic conductivity, effective macroporosity and Kosugi's lognormal pore size distribution model. Management related influences comprised three soil cover treatment (mustard and rye vs. fallow) and an initial mechanical soil disturbance with a rotary harrow. Environmental driving forces were derived from meteorological and soil moisture data. Soil hydraulic parameters varied over time by around one order of magnitude. The coefficient of variation of soil hydraulic conductivity K(h) decreased from 69.5% at saturation to 42.1% in the more unsaturated range (- 10 cm pressure head). A slight increase in the Kosugi parameter showing pore heterogeneity was observed under the rye cover crop, reflecting an enhanced structural porosity. The other hydraulic parameters were not significantly influenced by the soil cover treatments. Seedbed preparation with a rotary harrow resulted in a fourfold increase in macroporosity and hydraulic conductivity next to saturation, and homogenized the pore radius distribution. Re-consolidation after mechanical loosening lasted over 18 months until the soil returned to its initial state. The post-tillage trend of soil settlement could be approximated by an exponential decay function. Among environmental factors, wetting-drying cycles were identified as dominant driving force explaining short term hydraulic property changes within the season (r 2  = 0.43 to 0.59). Our results suggested that beside considering average

The Influence of Thickener Content on the Properties of Acryl Emulsion Resin

Energy Technology Data Exchange (ETDEWEB)

Park, Young Sam; Choi, Sang Goo [Department of Chemical Technology, Ho-Won University, Kunsan (Korea)

2001-04-01

HW-100 (acryl oligomer), Aerosil 200 (fine silica), HEMC (hydroxyethyl methylcellulose) and HPMC (hydroxypropyl methylcellulose) were each mixed with acryl emulsion resin. For each mixture, various physical properties were tested experimentally. HW-100 mixtures showed higher viscosity and thixotropy than the other mixtures. The viscosity increased rapidly with adding of thickener. Fabrication workability decreased substantially with increased thixotropy. Aerosil mixture represented good properties in workability, adhesive strength and water-resistance, however, it had large shrinkage. The shrinkage was typically influenced by content of water and void. HEMC mixture showed higher pH and adhesion than others, while HPMC mixture had long drying-time and excellent alkali-resistance characteristics. Water-resistance and alkali-resistance were mainly influenced by the molecular structure of thickener and the content of void. 26 refs., 12 figs.

Influence of the reduction-crucible material on the uranium properties

International Nuclear Information System (INIS)

Braga, F.J.C.; Bose, A.; Freitas, C.T. de

1979-01-01

The uranium obtained by UF 4 reduction using Mg in bombs coated with different materials such as alumina, blast furnace slag, Zirconia and graphite was studied. The reduction process involves a reaction that altains temperatures of the order of 1600 0 C at tightly closed enclosure environment. Assuming in this process that the only possible influencial agent on the reaction main product, i.e., metallic uranium is the own bomb coaling, different properties, mechanical-metallurgical and phase-transformation characteristics were examined and the influences of the coating materials were compared. The comparison of these properties was also studied in uranium refined by arc fusion. (Author) [pt

Influence of reduction conditions of NiO on its mechanical and electrical properties

Directory of Open Access Journals (Sweden)

Yehor Brodnikovskyi

2016-04-01

Full Text Available Yttria stabilized zirconia with a nickel catalyst (Ni-YSZ is the most developed, widely used cermet anode for manufacturing Solid Oxide Fuel Cells (SOFCs. Its electro-catalytic properties, mechanical durability and performance stability in hydrogen-rich environ­ments makes it the state of the art fuel electrode for SOFCs. During the reduction stage in initial SOFC operation, the virgin anode material, a NiO-YSZ mixture, is reduced to Ni-YSZ. The volume decrease associated with the change from NiO-YSZ to Ni-YSZ creates voids and causes structural changes, which can influence the physical properties of the anode. In this work, the structural, mechanical and electrical properties of NiO samples before and after reduction in pure H2 and a mixture of 5 vol. % H2-Ar were studied. The NiO to Ni phase transformations that occur in the anode under reducing and Reduction-Oxidation (RedOx cycling conditions and the impact on cell microstruc­ture, strength and electrical conductivity have been examined. Results show that the RedOx treatment of the NiO samples influence on their properties controversially, due to structural transfor­mation (formation of large amount of fine pores of the reduced Ni. It strengthened the treated samples yielding the highest mechanical strength values of 25.7 MPa, but from another side it is resulting in lowest electrical conductivity value of 1.9×105 S m-1 among all reduced samples. The results of this investigation shows that reduction conditions of NiO is a powerful tool for influence on properties of the anode substrate.

Case study II: application of the divalent cation bridging theory to improve biofloc properties and industrial activated sludge system performance-using alternatives to sodium-based chemicals.

Science.gov (United States)

Higgins, Matthew J; Sobeck, David C; Owens, Steven J; Szabo, Lynn M

2004-01-01

The objective of this study was to investigate the application of the divalent cation bridging theory (DCBT) as a tool in the chemical selection process at an activated sludge plant to improve settling, dewatering, and effluent quality. According to the DCBT, to achieve improvements, the goal of chemical selection should be to reduce the ratio of monovalent-to-divalent (M/D) cations. A study was conducted to determine the effect of using magnesium hydroxide [Mg(OH)2] as an alternative to sodium hydroxide (NaOH) at a full-scale industrial wastewater treatment plant. Floc properties and treatment plant performance were measured for approximately one year during two periods of NaOH addition and Mg(OH)2 addition. A cost analysis of plant operation during NaOH and Mg(OH)2 use was also performed. During NaOH addition, the M/D ratio was 48, while, during Mg(OH)2 addition, this ratio was reduced to an average of approximately 0.1. During the Mg(OH)2 addition period, the sludge volume index, effluent total suspended solids, and effluent chemical oxygen demand were reduced by approximately 63, 31, and 50%, respectively, compared to the NaOH addition period. The alum and polymer dose used for clarification was reduced by approximately 50 and 60%, respectively, during Mg(OH)2 addition. The dewatering properties of the activated sludge improved dewatering as measured by decreased capillary suction time and specific resistance to filtration (SRF), along with an increase in cake solids from the SRF test. This corresponded to a reduction in the volume of solids thickened by centrifuges at the treatment plant, which reduced the disposal costs of solids. Considering the costs for chemicals and solids disposal, the annual cost of using Mg(OH)2 was approximately 30,000 dollars to 115,000 dollars less than using NaOH, depending on the pricing of NaOH. The results of this study confirm that the DCBT is a useful tool for assessing chemical-addition strategies and their potential effect

Influence of dispersed particles on small and large deformation properties of concentrated caseinate composites

NARCIS (Netherlands)

Manski, J.M.; Kretzers, I.M.J.; Brenk, van S.; Goot, van der A.J.; Boom, R.M.

2007-01-01

Concentrated sodium caseinate composites (30% w/w in water), which contained either dispersed palm fat or glass spheres varying in size and surface properties were prepared in a Brabender Do-Corder kneader. The influence of the dispersed phase on the structural properties of the sodium caseinate

Influence of the elastomeric polypropylene addition on the properties of commercial metallocenic polypropylene

Directory of Open Access Journals (Sweden)

Marques Maria de Fátima V.

2001-01-01

Full Text Available Polypropylene with special properties can be obtained by metallocenic catalysts. These catalytic systems represent the beginning of a new age in polyolefins technology. In this work, the influence of the addition of a syndiotactic polypropylene (s-PP on the processability and mechanical properties of a commercial isotactic polypropylene (i-PP obtained by metallocenic catalysts was evaluated. Increasing addition of s-PP promoted better processability, with an increase in the impact strength and a decrease in the stress at break. A reduction of the crystallinity in the polymeric blends was verified. The more significant influence of the s-PP addition was observed for the mi-PP, compared to the ZNi-PP.

Influence of nitrogen on the growth and the properties of InAs quantum dots

International Nuclear Information System (INIS)

Schumann, O.

2004-01-01

This work investigates the influence of nitrogen incorporation on the growth and the optical properties of InAs quantum dots on GaAs(001) substrates. On the basis of systematic growth interruptions it was shown that the large quantum dots nucleate at dislocations, which are already formed during the growth of the wetting layer. After solving the growth problems, the influence of different combinations of matrix layers on the structural and optical properties of the quantum dots was investigated in the second part of this work. The strain and bandgap of these layers were varied systematically. (orig.)

Paste pumping and deposition field trials and concepts on Syncrude's dewatered mature fine tailings MFT centrifuge cake

Energy Technology Data Exchange (ETDEWEB)

Lahaie, R. [Syncrude Canada Ltd., Edmonton, AB (Canada); Ahmed, I.; Labelle, M.; Brown, R. [Golder Paste Technology, Sudbury, ON (Canada)

2009-07-01

This presentation discussed a paste pumping and deposition field study conducted on dewatered mature fine tailings (MFT) located at Syncrude's Mildred Lake operation. Bench scale rheological examinations of centrifuge cakes and design field testing are used to determine the pumpability of MFT centrifuge cakes. The study included a transportation assessment for the conveyor and positive displacement pumps and pipelines, as well as geotechnical and environmental analyses of bulk materials. Flocculant optimization and centrifuge operational parameter assessments were conducted. Pressure differential and flow rate data were captured in the field studies in order to determine pipeline friction loss. The study showed that pipe friction factors can be obtained using the Bingham plastic model. A natural deposition angle was determined for the MFT centrifuged cake. The study showed that the cake must be sheared in order to reduce yield stress before pumping. It was concluded that displacement pumps can be used to reduced pipeline friction factors. tabs., figs.

Insights on the Optical Properties of Estuarine DOM – Hydrological and Biological Influences

Science.gov (United States)

Santos, Luísa; Pinto, António; Filipe, Olga; Cunha, Ângela; Santos, Eduarda B. H.

2016-01-01

Dissolved organic matter (DOM) in estuaries derives from a diverse array of both allochthonous and autochthonous sources. In the estuarine system Ria de Aveiro (Portugal), the seasonality and the sources of the fraction of DOM that absorbs light (CDOM) were inferred using its optical and fluorescence properties. CDOM parameters known to be affected by aromaticity and molecular weight were correlated with physical, chemical and meteorological parameters. Two sites, representative of the marine and brackish water zones of the estuary, and with different hydrological characteristics, were regularly surveyed along two years, in order to determine the major influences on CDOM properties. Terrestrial-derived compounds are the predominant source of CDOM in the estuary during almost all the year and the two estuarine zones presented distinct amounts, as well as absorbance and fluorescence characteristics. Freshwater inputs have major influence on the dynamics of CDOM in the estuary, in particular at the brackish water zone, where accounted for approximately 60% of CDOM variability. With a lower magnitude, the biological productivity also impacted the optical properties of CDOM, explaining about 15% of its variability. Therefore, climate changes related to seasonal and inter-annual variations of the precipitation amounts might impact the dynamics of CDOM significantly, influencing its photochemistry and the microbiological activities in estuarine systems. PMID:27195702

The cause and influence of self-cementing properties of fine recycled concrete aggregates on the properties of unbound sub-base

International Nuclear Information System (INIS)

Poon, C.-S.; Qiao, X.C.; Chan, Dixon

2006-01-01

The use of coarse recycled concrete aggregates (CRCA) in conjunction with fine recycled concrete aggregates (FRCA) as sub-base materials has been widely studied. Although research results indicate that it is feasible to employ both CRCA and FRCA as granular sub-base, the influence of the unhydrated cement in the adhered mortar of the RCA on the properties of the sub-base materials has not been thoroughly studied. Generally, it is known that the strength of the sub-base materials prepared with RCA increases over time. However, this mechanism, known as the self-cementing properties, is not well understood and is believed to be governed by the properties of the fine portion of the RCA (<5 mm). This paper presents an investigation on the cause of the self-cementing properties by measuring X-ray diffraction patterns, pH values, compressive strength and permeability of various size fractions of the FRCA obtained from a commercially operated construction and demolition waste recycling plant. Their influence on the overall sub-base materials was determined. The results indicate that the size fractions of <0.15 and 0.3-0.6 mm (active fractions) were most likely to be the principal cause of the self-cementing properties of the FRCA. However, the effects on the properties of the overall RCA sub-base materials were minimal if the total quantity of the active fractions was limited to a threshold by weight of the total fine aggregate

Influence Of The Laser Cladding Strategies On The Mechanical Properties Of Inconel 718

International Nuclear Information System (INIS)

Lamikiz, A.; Tabernero, I.; Ukar, E.; Lopez de Lacalle, L. N.; Delgado, J.

2011-01-01

This work presents different experimental results of the mechanical properties of Inconel registered 718 test parts built-up by laser cladding. Recently, turbine manufacturers for aeronautical sector have presented high interest on laser cladding processes. This process allows building fully functional structures on superalloys, such as Inconel registered 718, with high flexibility on complex shapes. However, there is limited data on mechanical properties of the laser cladding structures. Moreover, the available data do not include the influence of process parameters and laser cladding strategies. Therefore, a complete study of the influence of the laser cladding parameters and mainly, the variation of the tensile strength with the laser cladding strategy is presented. The results show that there is a high directionality of mechanical properties, depending on the strategies of laser cladding process. In other words, the test parts show a fiber -like structure that should be considered on the laser cladding strategy selection.

Influence of solution annealing on microstructure and mechanical properties of Maraging 300 steel

Energy Technology Data Exchange (ETDEWEB)

Lima Filho, Venceslau Xavier; Barros, Isabel Ferreira; Abreu, Hamilton Ferreira Gomes de, E-mail: venceslau@ifce.edu.br [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil). Departamento de Engenharia Metalurgica e Materiais. Laboratorio de Caracterizacao de Materiais, Metalurgia Fisica e Grupo de Pesquisa de Transformacao de Fase

2017-01-15

Maraging 300 belongs to a family of metallic materials with extremely high mechanical strength and good toughness. Some works have been published about aging temperatures that improve ultimate strength resistance with acceptable toughness levels in this steel family, where the prior austenite grain size obtained by different solution annealing temperature influence in the final mechanical properties. Solution annealing temperatures ranging from 860 °C to 1150 deg C and were kept constant until the aging temperature. These treatments were used in order to investigate their influence on the microstructure and mechanical properties of maraging steel 300, especially with regard to toughness. The characterization of the microstructure was performed by optical microscopy, scanning electron microscope (SEM) and X-ray diffraction (XRD). Mechanical properties were evaluated by Rockwell C hardness and Charpy impact tests. The results showed that there is a temperature range where one can get some improvement in toughness without a large loss of mechanical strength. (author)

Influence of tempering temperature on mechanical properties of cast steels

Directory of Open Access Journals (Sweden)

G. Golański

2008-12-01

Full Text Available The paper presents results of research on the influence of tempering temperature on structure and mechanical properties of bainite hardened cast steel: G21CrMoV4 – 6 (L21HMF and G17CrMoV5 – 10 (L17HMF. Investigated cast steels were taken out from internal frames of steam turbines serviced for long time at elevated temperatures. Tempering of the investigated cast steel was carried out within the temperature range of 690 ÷ 730 C (G21CrMoV4 – 6 and 700 ÷ 740 C (G17CrMoV5 – 10. After tempering the cast steels were characterized by a structure of tempered lower bainite with numerous precipitations of carbides. Performed research of mechanical properties has shown that high temperatures of tempering of bainitic structure do not cause decrease of mechanical properties beneath the required minimum.oo It has also been proved that high-temperature tempering (>720 oC ensures high impact energy at the 20% decrease of mechanical properties.

Influence of supplementary cementitious materials on water transport kinetics and mechanical properties of hydrated lime and cement mortars

Directory of Open Access Journals (Sweden)

Ince, C.

2015-06-01

Full Text Available The purpose of this paper is an investigation of the possible role of supplementary cementitious materials (SCMs on water transport kinetics and mechanical properties of hydrated lime (CL90 and Portland cement (PC mortars. The properties of hydrated lime are significantly different from those of cement and therefore modifying fresh and hardened properties of these mortars are vital for mortar/substrate optimisation in masonry construction. The parameters investigated in this paper often are the main barriers to the use of hydrated lime in construction practice. The results show that transfer sorptivity and time to dewater freshly-mixed hydrated lime mortars can be modified when binder is partially replaced with SCMs. Compressive strength of CL90 mortars is increased systematically with the increased replacement levels of SCMs and the results are supported with the microstructural images. The ability to modify the water transport kinetics and mechanical properties allows compatibility between the mortar and the substrate unit in masonry construction.El objetivo de este artículo es investigar el papel de los materiales cementantes suplementarios (SCMs en la cinética de transporte del agua y en las propiedades mecánicas de los morteros de cal hidratada (CL90 y cemento Portland. Las propiedades de la cal hidratada son significativamente diferentes a las del cemento y por lo tanto el control de las propiedades de los morteros frescos y endurecidos es fundamental en la optimización mortero/substrato en albañilería. Los parámetros estudiados en este trabajo son a menudo las principales barreras para el uso de la cal hidratada en la práctica de la construcción. Los resultados indican que la absortividad y el tiempo necesario para deshidratar morteros de cal hidratada recién mezclados pueden ser controlados cuando el conglomerante es parcialmente remplazado por SCMs. La resistencia a compresión de los morteros CL90 aumenta sistem

Influence of the microwave irradiation dewatering on the combustion characteristics of Chinese brown coals

Science.gov (United States)

Ge, Lichao; Feng, Hongcui; Xu, Chang; Zhang, Yanwei; Wang, Zhihua

2018-02-01

This study investigates the influence of microwave irradiation on coal composition, pore structure, coal rank, and combustion characteristics of typical brown coals in China. Results show that the upgrading process significantly decreased the inherent moisture, and increased calorific value and fixed carbon content. After upgrading, pore distribution extended to micropore region, oxygen functional groups were reduced and destroyed, and the apparent aromaticity increased suggesting an improvement in the coal rank. Based on thermogravimetric analysis, the combustion processes of upgraded coals were delayed toward the high temperature region, and the temperatures of ignition, peak and burnout increased. Based on the average combustion rate and comprehensive combustion parameter, the upgraded coals performed better compared with raw brown coals and a high rank coal. In ignition and burnout segments, the activation energy increased but exhibited a decrease in the combustion stage.

Influence of the precursors on the properties of alumina supported rhodium particles

International Nuclear Information System (INIS)

Coq, B.; Figueras, F.; Tazi, T.

1989-01-01

The effect of chlorine on the properties of Rh particles supported on alumina was studied using the hydroconversion of alkanes as a molecular probe. Chloride ions on the alumina have little influence on the Rh particles. Chlorine adsorbed on the Rh particles decreases the chemisorption capacity and increases the metal-support interaction, which results in modifications of their catalytic properties. Depending on the alkane processed, specific activity can be depressed up to four orders of magnitude. (orig.)

The influence of clay minerals on acoustic properties of sandstones

Energy Technology Data Exchange (ETDEWEB)

Hansen, Olav

1997-12-31

This thesis aims to provide better understanding of the relationship between the acoustic properties and the petrophysical/mineralogical properties in sand-prone rock. It emphasizes the influence of clay minerals. The author develops a method to deposit clay minerals/mineral aggregates in pore space of a rigid rock framework. Kaolinite aggregates were flushed into porous permeable Bentheimer sandstone to evaluate the effect of pore filling minerals on porosity, permeability and acoustic properties. The compressional velocity was hardly affected by the clay content and it was found that the effect of minor quantities of pore filling minerals may be acoustically modelled as an ideal suspension, where the pore fluid bulk modulus is modified by the bulk modulus of the clay minerals. The influence of clays on acoustic velocities in petroleum reservoir rocks was investigated through ultrasonic measurements of compressional- and shear-waves on core material from reservoir and non-reservoir units on the Norwegian Continental Shelf. The measured velocities decrease as the porosity increases, but are not strongly dependent on the clay content. The measured velocities are less dependent on the petrophysical and lithological properties than indicated by previous authors and published mathematical models, and stiffness reduction factors are introduced in two of the models to better match the data. Velocities are estimated along the wellbores based on non-sonic well logs and reflect well the actual sonic log well measurements. In some wells the compressional velocity cannot be modelled correctly by the models suggested. Very high compressional wave anisotropy was measured in the dry samples at atmospheric conditions. As the samples were saturated, the anisotropy was reduced to a maximum of about 30% and decreases further upon pressurization. Reservoir rocks retrieved from 2500 m are more stress dependent than those retrieved from less than 200 m depth. 168 refs., 117 figs., 24

Examination of the influence of heat treatment on the properties of Al-Si alloys

Energy Technology Data Exchange (ETDEWEB)

Vuksanovic, D.; Rakocevic, S. [Faculty of Metallurgy, Podgorica (RS); Markovic, S. [Faculty of Technology and Metallurgy, Belgrade (RS); Petrovic, T. [Institute ' Kirilo Savic' , Belgrade (RS); Kovacevic, K. [Institute for Ferrous Metallurgy (RS); Tripkovic, S. [H.K. Petar Drapsin, Mladenovac (RS)

2007-08-15

In this paper the influence of heat treatment on the structural and mechanical properties of Al-Si alloys was investigated. Silicon content in the examined alloys was in the range 11 to 14%, the contents of the other alloying elements were in the standard range but all alloys were modified with strontium. The regime of the applied heat treatment was quenching (520 C/6h - cooling in water) + aging (205oC/7h - air cooling). The examinations were carried out at room temperature as well as at 250 C and 300 C. The obtained results showed a positive influence of the applied heat treatment on the mechanical properties of the examined alloys. The improvement of the mechanical properties can be considered as a consequence of a redistribution and change of morphology of the phases present in the structure of the alloys. (orig.)

Influence of color on dielectric properties of marinated poultry breast meat.

Science.gov (United States)

Samuel, D; Trabelsi, S

2012-08-01

The dielectric behavior of foods when exposed to radio-frequency and microwave electric fields is highly influenced by moisture content and the degree of water binding with constituents of the food materials. The ability to correlate specific food quality characteristics with the dielectric properties can lead to the development of rapid, nondestructive techniques for such quality measurements. Water-holding capacity is a critical attribute in meat quality. Up to 50% of raw poultry meat in the United States is marinated with mixtures of water, salts, and phosphates. The objective of this study was to determine if variations in breast meat color would affect the dielectric properties of marinated poultry meat over a broad frequency range from 500 MHz to 50 GHz. Poultry meat was obtained from a local commercial plant in Georgia (USA). Color and pH measurements were taken on the breast filets. Groups of breast filets were sorted into classes of pale and normal before adding marination pickup percentages of 0, 5, 10, and 15. Breast filets were vacuum-tumbled and weighed for pickup percentages. Dielectric properties of the filets were measured with a coaxial open-ended probe on samples equilibrated to 25°C. Samples from pale meat exhibited higher dielectric properties than samples from normal meat. No differences could be observed between samples from pale and normal meat after marination of the samples. Overall, dielectric properties increased as the marination pickup increased (α=0.05). Marination pickup strongly influenced the dielectric loss factor. Differences between samples marinated at different pickup levels were more pronounced at lower frequencies for the dielectric loss factor. As frequency increased, the differences between samples decreased. Differences in dielectric constant between samples were not as consistent as those seen with the dielectric loss factor.

Influence of La Doping on Magnetic and Optical Properties of Bismuth Ferrite Nanofibers

Directory of Open Access Journals (Sweden)

Ziang Zhang

2012-01-01

Full Text Available The influence of La doping on the crystal structure, ferromagnetic, and optical properties of BFO nanofibers was investigated. Bi1−xLaxFeO3 ultrafine nanofibers were synthesized by the electrospinning method. The surface morphology and crystal structure of the as-spun and sintered fibers were not affected by the doping. The impurity phases of the BFO crystals were weakened with the increment of La concentration. The magnetization field curves showed that the magnetization weakened under low La doping proportion, but strengthened with the increase of the doped proportion. The magnetization curves also showed continuous strong enhancement of ferromagnetic behavior. The results of UV-vis and photoabsorption testing revealed little influence of La doping on the optical property.

The Influence of Textile Materials Mechanical Properties upon Virtual Garment Fit

Directory of Open Access Journals (Sweden)

Kristina ANCUTIENĖ

2011-07-01

Full Text Available 3D virtual representation of garment provides high potential for design, product development and marketing processes, especially in mass customization strategies implementation. Clothing industry rapidly turns to virtual simulation which not only presents realistic 3D view of garment but also simulates mechanical behaviour of materials. 3D CAD systems can be used to define strain distribution in virtual garment which describes garment fit without actually producing the garment. Strain and distance ease between body and garment depends not only upon body measurements and garment construction, but also on mechanical and structural properties of selected material. The aim of this research was to investigate virtual garment fit using "Modaris 3D Fit" (Lectra software subjected to fabrics mechanical (tensile, bending, shear and structural (composition, thickness, area density properties investigating strain distribution in garment and distance ease between garment and human body. It was defined that for diagonal cut garments the highest influence upon garment fit has fabric tensile properties in weft direction. The highest influence is obtained at high distance ease and small strain values zones and at negative distance ease and high strain values zones. Therefore, presented method could be used for tight-fitted garments also for garments with draperies on purpose to investigate garment fit upon fabrics used.http://dx.doi.org/10.5755/j01.ms.17.2.486

The influence of roller compaction processing variables on the rheological properties of granules

Directory of Open Access Journals (Sweden)

Tim Freeman

2016-08-01

The results demonstrate several rheological properties of the granulate, which have been shown to be closely correlated with variance in die filling and tablet strength, and are predictably influenced by the processing parameters.

The study of the influence of helium on the counter's measurement properties

International Nuclear Information System (INIS)

Guan Rui; Weng Kuiping; Ren Xingbi

2009-04-01

In measurement of tritium by the proportional counter, methane is usually used as counter gas. Gas samples have been made with helium and methane in the proportion of concentration and measured to study the influence of helium on the counter's measurement properties. Then gas sample with tritium and helium has been measured, and the result is according with anticipation. The experiment has showed that the plateau curve of counter could be changed by helium, but the influence could be ignored when helium concentration less 10%. (authors)

Influence of boron oxide on protective properties of zinc coating on steel

International Nuclear Information System (INIS)

Alimov, V.I.; Berezin, A.V.

1986-01-01

The authors study the properties of zinc coating when boron oxide is added to the melt for galvanization. The authors found that a rise in the degree of initial deformation of the steel leads to the production of varying thickness of the zinc coating. The results show the favorable influence of small amounts of added boron oxide on the corrosion resistance of a zinc coating on cold-deformed high-carbon steel; this influence is also manifested in the case of deformation of the zinc coating itself

Dewaterability of five sewage sludges in Guangzhou conditioned with Fenton's reagent/lime and pilot-scale experiments using ultrahigh pressure filtration system.

Science.gov (United States)

Liang, Jialin; Huang, Shaosong; Dai, Yongkang; Li, Lei; Sun, Shuiyu

2015-11-01

Sludge conditioning with Fenton's reagent and lime is a valid method for sludge dewatering. This study investigated the influence of different organic matter content sludge on sludge dewatering and discussed the main mechanism of sludge conditioning by combined Fenton's reagent and lime. The results indicated that the specific resistance to filterability (SRF) of sludge was reduced efficiently by approximately 90%, when conditioned with Fenton's reagent and lime. Through single factor experiments, the optimal conditioning combinations were found. In addition, the relationship between VSS% and consumption of the reagents was detected. Furthermore, it was also demonstrated that the SRF and filtrate TOC values had a significant correlation with VSS% of sludge (including raw and conditioned). The main mechanism of sludge dewatering was also investigated. Firstly, it revealed that the dewaterability of sludge was closely correlated to extracellular polymeric substances (EPS) and bound water contents. Secondly, the results of scanning electron microscopy (SEM) stated that sludge particles were to be smaller and thinner after conditioning. And this structure could easily form outflow channels for releasing free water. Additionally, with the ultrahigh pressure filtration system, the water content of sludge cake conditioned with Fenton's reagent and lime could be reduced to below 50%. Moreover, the economic assessment shows that Fenton's reagent and lime combined with ultrahigh pressure filtration system can be an economical and viable technology for sewage sludge dewatering. Finally, three types of sludge were classified: (1) Fast to dewater; (2) Moderately fast to dewater; (3) Slow to dewater sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

The influence of processing conditions on the microstructure and the mechanical properties of reaction sintered silicon nitride

International Nuclear Information System (INIS)

Heinrich, J.

1979-09-01

The microstructure of reaction sintered silicon nitride (RBSN) was changed in a wide range of varying green density, grain size of the silicon starting powder, nitriding conditions, and by introducing artificial pores. The influence of single microstructural parameters on mechanical properties like room temperature strength, creep behaviour, and resistance to thermal shock has been investigated. The essential factors influencing these properties were found to be total porosity, pore size distribution, and the fractions of α- and β-Si 3 N 4 . In view of high temperature engineering applications of RBSN possibilities to optimize the material's properties by controlled processing are discussed. (orig.) [de

Research of influence of open-winding faults on properties of brushless permanent magnets motor

Science.gov (United States)

Bogusz, Piotr; Korkosz, Mariusz; Powrózek, Adam; Prokop, Jan; Wygonik, Piotr

2017-12-01

The paper presents an analysis of influence of selected fault states on properties of brushless DC motor with permanent magnets. The subject of study was a BLDC motor designed by the authors for unmanned aerial vehicle hybrid drive. Four parallel branches per each phase were provided in the discussed 3-phase motor. After open-winding fault in single or few parallel branches, a further operation of the motor can be continued. Waveforms of currents, voltages and electromagnetic torque were determined in discussed fault states based on the developed mathematical and simulation models. Laboratory test results concerning an influence of open-windings faults in parallel branches on properties of BLDC motor were presented.

Research of influence of open-winding faults on properties of brushless permanent magnets motor

Directory of Open Access Journals (Sweden)

Bogusz Piotr

2017-12-01

Full Text Available The paper presents an analysis of influence of selected fault states on properties of brushless DC motor with permanent magnets. The subject of study was a BLDC motor designed by the authors for unmanned aerial vehicle hybrid drive. Four parallel branches per each phase were provided in the discussed 3-phase motor. After open-winding fault in single or few parallel branches, a further operation of the motor can be continued. Waveforms of currents, voltages and electromagnetic torque were determined in discussed fault states based on the developed mathematical and simulation models. Laboratory test results concerning an influence of open-windings faults in parallel branches on properties of BLDC motor were presented.

The influence of compound admixtures on the properties of high-content slag cement

Energy Technology Data Exchange (ETDEWEB)

Dongxu, L.; Xuequan, W.; Jinlin, S.; Yujiang, W.

2000-01-01

Based on the activation theory of alkali and sulfate, the influence of compound admixtures on the properties of high-content slag cement was studied by testing the strength, pore structure, hydrates, and microstructure, Test results show that compound admixtures can obviously improve the properties of high-content slag cement. The emphasis of the present research is two-fold: substituting gypsum with anhydrite and calcining gypsum. These both can improve early and later performance.

Influence of molecular weight on the fracture properties of aliphatic polyketone terpolymers

NARCIS (Netherlands)

Zuiderduin, W.C.J.; Homminga, D.S.; Homminga, D.S.; Huetink, Han; Gaymans, R.J.

2003-01-01

The influence of polymer molecular weight on the mechanical properties of aliphatic polyketones was investigated. The molecular weight varied from 100,000 to 300,000 g mol21. The crystallinity was found to be independent of polymer molecular weight, as was the glass transition temperature. The yield

Influence of industrial solid waste addition on properties of soil-cement bricks

Directory of Open Access Journals (Sweden)

F. B. Siqueira

Full Text Available Abstract The reuse of pollutant solid wastes produced in distinct industrial activities (avian eggshell waste and welding flux slag waste as a source of alternative raw material for producing soil-cement bricks for civil construction was investigated. Soil-cement bricks containing up to 30 wt% of industrial solid waste were uniaxially pressed and cured for 28 days. Special emphasis is given on the influence of solid waste addition on the technical properties (as such volumetric shrinkage, water absorption, bulk density, durability, and compressive strength, microstructure and mineral phases of soil-cement bricks. Microstructural evolution was evaluated via confocal microscopy. The experimental results showed that the solid wastes behave as charge material and influenced both technical properties and microstructure of the soil-cement bricks. It was found that up to 15 wt% of welding flux slag waste and up to 30 wt% of avian eggshell waste could be added into the soil-cement bricks for use as building material.

Dysport: pharmacological properties and factors that influence toxin action.

Science.gov (United States)

Pickett, Andy

2009-10-01

The pharmacological properties of Dysport that influence toxin action are reviewed and compared with other botulinum toxin products. In particular, the subject of diffusion is examined and discussed based upon the evidence that currently exists, both from laboratory studies and from clinical data. Diffusion of botulinum toxin products is not related to the size of the toxin complex in the product since the complex dissociates under physiological conditions, releasing the naked neurotoxin to act. The active neurotoxin in Type A products is the same and therefore diffusion is equal when equal doses are administered.

Influence of physicochemical properties of rice flour on oil uptake of tempura frying batter.

Science.gov (United States)

Nakamura, Sumiko; Ohtsubo, Ken'ichi

2010-01-01

The physicochemical properties of rice flour and wheat flour influenced the oil uptake of tempura frying batter. Rice flour was better than wheat flour in the overall quality and crispness of the fried tempura batter. Rice flour resisted oil absorption more than wheat flour, and a higher level of apparent starch amylose and higher consistency/breakdown ratio of the pasting properties led to a lower oil uptake of the batter. Super hard EM10 rice showed the highest apparent amylose content and higher consistency/breakdown ratio than the other flour samples, the batter from EM10 revealing the lowest oil content after frying among all the batters examined. The apparent amylose content, consistency/breakdown ratio and oil absorption index are proposed as useful guides for oil absorption when frying from among the physicochemical properties that influence the oil content of fried batter. Our proposal for the "oil absorption index" could be a simple, although not perfect method for estimating the oil content of batter flour.

Influence of spray drying operating conditions on microencapsulated rosemary essential oil properties

Directory of Open Access Journals (Sweden)

Regiane Victória de Barros Fernandes

2013-02-01

Full Text Available Spray drying is an important method used by the food industry in the production of microencapsulated flavors to improve handling and dispersion properties. The objective of this study was to evaluate the influence of the process conditions on the properties of rosemary essential oil microencapsulated by spray drying using gum Arabic as encapsulant. The effects of the wall material concentration (10-30%, inlet air temperature (135-195 ºC, and feed flow rate (0.5-1.0 L.h-1 on the moisture content, hygroscopicity, wettability, solubility, bulk and tapped densities, particle density, flowability, and cohesiveness were evaluated using a 2³ central composite rotational experimental design. Moisture content, hygroscopicity and wettability were significantly affected by the three factors analyzed. Bulk density was positively influenced by the wall material concentration and negatively by the inlet air temperature. Particle density was influenced by the wall material concentration and the inlet air temperature variables, both in a negative manner. As for the solubility, tapped density, flowability, and cohesiveness, the models did not fit the data well. The results indicated that moderate wall material concentration (24%, low inlet air temperature (135 ºC, and moderate feed flow rate (0.7 L.h-1 are the best spray drying conditions.

The Influence of Three-Layer Knitted Fabrics’ Structure on Electrostatic and Comfort Properties

Directory of Open Access Journals (Sweden)

Sandra VARNAITĖ ŽURAVLIOVA

2013-12-01

Full Text Available In our times, when electricity and electrical devices are around us every day, it is very important to be protected from electrostatic discharge. The best protection from electric charge dissipation provides conductive textile materials. For the last few decades fine and flexible conductive yarns were developed, which ensure very good electrostatic properties. Unfortunately, due to their chemical nature, these yarns do not distinguish good comfort properties. The main purpose of development of such textiles is to determine the influence of conductive yarns and hollow fiber yarns arrangements in the middle layer of the three layer weft-knitted fabrics to electrostatic and comfort properties. So, in order to have flexible textile materials with good electrostatic and comfort properties, multifunctional three layer weft-knitted fabrics of combined pattern were designed and manufactured for this research work. Two groups of polyester based three layer knitted fabrics with different arrangement of conductive yarns (such as carbon core yarn and polyester silver coated yarn and polyester yarn of special design (Coolmax®, Thermolite® were investigated. The parameters of electrostatic characteristics, such as surface and vertical resistances as well as charge decay properties were measured. The results have showed that all tested fabrics have excellent shielding properties. The main influence on the electrostatic properties of tested fabrics has the arrangement of conductive carbon core yarns inserted in the knits. In order to evaluate the comfort of knitted fabrics the air permeability, hygroscopicity, time of absorption and drying degree of fabrics were evaluated. It was determined, that the values of comfort parameters depend on the quantity and distribution of Coolmax® and Thermolite® yarns in the fabrics.DOI: http://dx.doi.org/10.5755/j01.ms.19.4.2235

Influence of increasing amount of recycled concrete powder on mechanical properties of cement paste

Science.gov (United States)

Topič, Jaroslav; Prošek, Zdeněk; Plachý, Tomáš

2017-09-01

This paper deals with using fine recycled concrete powder in cement composites as micro-filler and partial cement replacement. Binder properties of recycled concrete powder are given by exposed non-hydrated cement grains, which can hydrate again and in small amount replace cement or improve some mechanical properties. Concrete powder used in the experiments was obtained from old railway sleepers. Infrastructure offer more sources of old concrete and they can be recycled directly on building site and used again. Experimental part of this paper focuses on influence of increasing amount of concrete powder on mechanical properties of cement paste. Bulk density, shrinkage, dynamic Young’s modulus, compression and flexural strength are observed during research. This will help to determine limiting amount of concrete powder when decrease of mechanical properties outweighs the benefits of cement replacement. The shrinkage, dynamic Young’s modulus and flexural strength of samples with 20 to 30 wt. % of concrete powder are comparable with reference cement paste or even better. Negative effect of concrete powder mainly influenced the compression strength. Only a 10 % cement replacement reduced compression strength by about 25 % and further decrease was almost linear.

Cutting down operating costs at sewage treatment plant through aimed application of new characterization methods; Betriebskostenreduzierung auf Klaeranlagen durch gezielte Anwendung neuer Charakterisierungsmethoden

Energy Technology Data Exchange (ETDEWEB)

Friedrich, H.; Potthoff, A. [Fraunhofer-Institut fuer Keramische Technologien und Sinterwerkstoffe (IKTS), Dresden (Germany); Friedrich, E. [Ingenieurgesellschaft fuer Wasser und Entsorgung mbH, Radebeul (Germany)

1999-07-01

Mechanical dewatering of sewage sludge is state of the art. Because of increasing cost, more stringent regulations (act on waste recycling 'Kreislaufwirtschaftsgesetz' and the technical code on municipal waste), and the lack of landfill space, expensive thermal processing techniques are gaining ever greater weight. To assure that disposal costs remain reasonable, mechanical dewatering must be more and more enhanced. The following need to be optimized and enhanced: sludge properties, conditioning, and dewatering. (orig.) [German] Klaerschlaemme maschinell zu entwaessern ist Stand der Technik. Steigende Kosten, verschaerfte Bestimmungen (Kreislaufwirtschaftsgesetz, TA Siedlungsabfall) und fehlende Deponien geben den teuren thermischen Behandlungsverfahren ein immer groesseres Gewicht. Damit die Entsorgung bezahlbar bleibt, muss immer staerker mechanisch entwaessert werden. Optimiert und verbessert werden muessen die Schlammeigenschaften, die Konditionierung und die Entwaesserung. (orig.)

Fuel properties of biodiesel from vegetable oils and oil mixtures. Influence of methyl esters distribution

International Nuclear Information System (INIS)

Martínez, G.; Sánchez, N.; Encinar, J.M.; González, J.F.

2014-01-01

In this work, the quality of biodiesel produced by basic transesterification from several vegetable oils (soybean, rapeseed, sunflower, high oleic sunflower, Cynara Cardunculus L., Brassica Carinata and Jatropha Curca) cultivated in Extremadura has been studied in detail. The influence of raw material composition on properties such as density, viscosity, cetane number, higher heating value, iodine and saponification values and cold filter plugging point has been verified. Other biodiesel properties such as acid value, water content and flash and combustion points were more dependent on characteristics of production process. Biodiesel produced by rapeseed, sunflower and high oleic sunflower oils transesterification have been biofuels with better properties according to Norm EN 14214. Finally, it has been tested that it is possible to use oils mixtures in biodiesel production in order to improve the biodiesel quality. In addition, with the same process conditions and knowing properties of biodiesel from pure oils; for biodiesel from oils mixtures, its methyl esters content, and therefore properties dependent this content can be predicted from a simple mathematical equation proposed in this work. - Highlights: • Biodiesel quality produced by basic transesterification from vegetable oils. • We examine influences of methyl esters distribution on biodiesel properties. • Biofuels from soybean, sunflower and rapeseed oils were with better properties. • Oils mixtures improve biodiesel quality to fulfill Norm EN 14214. • An equation to predict properties of biodiesel from oil mixtures is proposed

Influence of Silicon-Containing Additives on Concrete Waterproofness Property

Science.gov (United States)

Butakova, M. D.; Saribekyan, S. S.; Mikhaylov, A. V.

2017-11-01

The article studies the influence of silicon-containing additives on the property of the water resistance of concrete samples. It provides a review of the literature on common approaches and technologies improving concrete waterproofness and reinforced concrete structures. Normal hardening samples were obtained on the basis of concretes containing microsilica, aerosil or ash, or the combinations thereof. This research is aimed at the study of the complex modifier effect r on the basis of metakaolin, superplasticizer and silicon containing additives on the property of concrete water resistance. The need to use a superplasticizer to reduce the water-cement ratio and metakaolin as a hardening accelerator along with the set of strength is substantiated. This article describes a part of the results of the experiment conducted to find alternative options for colmatizing expensive additives used in the concreting foundations of private house-building. The implementation of the scientific work will not only clarify this area but will also broaden the knowledge of such additive as aerosol.

Influence of inductive heating on microstructure and material properties in roll forming processes

Science.gov (United States)

Guk, Anna; Kunke, Andreas; Kräusel, Verena; Landgrebe, Dirk

2017-10-01

The increasing demand for sheet metal parts and profiles with enhanced mechanical properties by using high and ultra-high-strength (UHS) steels for the automotive industry must be covered by increasing flexibility of tools and machines. This can be achieved by applying innovative technologies such as roll forming with integrated inductive heating. This process is similar to indirect press hardening and can be used for the production of hardened profiles and profiles with graded properties in longitudinal and traverse direction. The advantage is that the production of hardened components takes place in a continuous process and the integration of heating and quenching units in the profiling system increases flexibility, accompanied by shortening of the entire process chain and minimizing the springback risk. The features of the mentioned process consists of the combination of inhomogeneous strain distribution over the stripe width by roll forming and inhomogeneity of microstructure by accelerated inductive heating to austenitizing temperature. Therefore, these two features have a direct influence on the mechanical properties of the material during forming and hardening. The aim of this work is the investigation of the influence of heating rates on microstructure evolution and mechanical properties to determine the process window. The results showed that heating rate should be set at 110 K/s for economic integration of inductive heating into the roll forming process.

Influences of the steam sterilization on the properties of calcium phosphate porous bioceramics.

Science.gov (United States)

Li, Xiangfeng; Guo, Bo; Xiao, Yumei; Yuan, Tun; Fan, Yujiang; Zhang, Xingdong

2016-01-01

The influences of steam sterilization on the physicochemical properties of calcium phosphate (Ca-P) porous bioceramics, including β-tricalcium phosphate (β-TCP), biphasic calcium phosphate (BCP) and hydroxyapatite (HA) are investigated. After being steam sterilized in an autoclave (121 °C for 40 min), the porous bioceramics are dried and characterized. The steam sterilization has no obvious effects on the phase composition, thermal stability, pH value and dissolubility of β-TCP porous bioceramic, but changes its morphology and mechanical strength. Meanwhile, the steam sterilization leads to the significant changes of the morphology, phase composition, pH value and dissolubility of BCP porous bioceramic. The increase of dissolubility and mechanical strength, the decrease of pH value of the immersed solution and partial oriented growth of crystals are also observed in HA porous bioceramic after steam sterilization. These results indicate that the steam sterilization can result in different influences on the physicochemical properties of β-TCP, BCP and HA porous bioceramics, thus the application of the steam sterilization on the three kinds of Ca-P porous bioceramics should be considered carefully based on the above changed properties.

Influence of heat-treatment on lithium ion anode properties of mesoporous carbons with nanosheet-like walls

Energy Technology Data Exchange (ETDEWEB)

Zeng, Fanyan [College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China); Hou, Zhaohui, E-mail: zhqh96@163.com [College of Chemistry and Chemical Engineering, Hunan Institute of Science and Technology, Yueyang 414006 (China); He, Binhong [College of Chemistry and Chemical Engineering, Hunan Institute of Science and Technology, Yueyang 414006 (China); Ge, Chongyong; Cao, Jianguo [College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China); Kuang, Yafei, E-mail: yafeik@163.com [College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China)

2012-08-15

Highlights: ► Mesoporous carbons possess unique nanosheet-like pore walls which can be changed by heat treatment. ► Lithium ion anode properties of mesoporous carbons could be influenced by the nanosheet-like walls. ► Mesoporous carbons with nanosheet-like walls exhibit enhanced electrochemical properties LIBs. -- Abstract: Mesoporous carbons (MCs) with nanosheet-like walls have been prepared as electrodes for lithium-ion batteries by a simple one-step infiltrating method under the action of capillary flow. The influence of heat treatment temperature on the surface topography, pore/phase structure and anode performances of as-prepared materials has been investigated. The results reveal that melted liquid-crystal polycyclic aromatic hydrocarbons could be anchored on liquid/silica interfaces by molecule engineering. After carbonization, the nanosheets are formed as the pore walls of MCs and are perpendicular to the long axis of pores. The anode properties demonstrate that C-1200 displays higher reversible capacitance than those treated in higher temperature. The rate performances of C-1200 and C-1800 are similar and more excellent than that of C-2400. These improved lithium ion anode properties could be attributed to the nanosheet-like walls of MCs which can be influenced by the heat treatment temperature.

Influence of Polylactide Modification with Blowing Agents on Selected Mechanical Properties

Directory of Open Access Journals (Sweden)

Aneta Tor-Świątek

2017-12-01

Full Text Available Article presents research of modification of PLA with four types of chemical blowing agents with a different decomposition characteristic. The modification was done both cellular extrusion and injection molding processes. Obtained results shows that dosing blowing agents have the influence on mechanical properties and structure morphology of PLA. The differences in obtained results are also visible and significant between cellular processes.

Influence of dysprosium and terbium additions on aluminium structure and properties

International Nuclear Information System (INIS)

Fridlyander, I.N.; Sokolovskaya, E.M.; Zimina, E.N.; Tkachenko, E.A.; Artemova, M.S.

1992-01-01

The influence of 0.3%Dy and 0.3%Tb additions were investigated on grain size in aluminium ingots and on recrystallization and mechanical properties in 1.5 mm thick sheets. Grain refinement in ingots was revealed along with an increase of sheet recrystallization temperature and grain growth retardation in the process of secondary recrystallization. Ultimate strength was found to rise at some decrease of specific elongation

The influence of gamma radiation on HDPE properties for tibial tray

International Nuclear Information System (INIS)

Sulistioso, G.S.; Dewi, R.K.; Maria, C.P.; Nada, M.

2012-01-01

A research on HDPE as tibial tray in total knee joint replacement surgery has been done. The aims of this research were to characterize the influence of gamma radiation on chemical, and mechanical properties on HDPE is made by using hot press method then irradiated with various doses of gamma rays of 0 kGy, 25 kGy, 50 kGy, 75 kGy, 100 kGy, 125 kGy, and 150 kGy at a dose rate 9 kGy/h. The irradiated HDPE were tested for their chemical, and mechanical properties. The chemical properties test, involve crosslinking and free radicals. The mechanical properties test, involve hardness, tensile strength, and elongation at break. The results showed that gamma radiation from IRKA IV th category can enhance the, chemical properties of HDPE in terms of percentage and number of radical crosslinking and mechanical properties of HDPE in terms of hardness, tensile strength and elongation at break with different changes from the initial state before radiation also the optimum dose to obtain better physical, chemical, and mechanical properties of HDPE, crosslinking percentage at 99.71%; height of radical peroxide curve at 13 cm; hardness (shore A) at 94.33; modulus of elasticity at 1113.03 N/mm 2 ; yield stress at 26.38 N/mm 2 ; tensile strength at 31.11 N/mm 2 ; and elongation at break at 440.37%, so that HDPE can be used as tibial tray. (author)

Influence of electrical sheet width on dynamic magnetic properties

CERN Document Server

Chevalier, T; Cornut, B

2000-01-01

Effects of the width of electrical steel sheets on dynamic magnetic properties are investigated by solving diffusion equation on the cross-section of the sheet. Linear and non-linear cases are studied, and are compared with measurement on Epstein frame. For the first one an analytical solution is found, while for the second, a 2D finite element simulation is achieved. The influence of width is highlighted for a width thickness ratio lower than 10. It is shown that the behaviour modification in such cases is conditioned by the excitation signal waveform, amplitude and also frequency.

Influence of soil properties on the behavior of heated on bottom pipelines

Energy Technology Data Exchange (ETDEWEB)

Hallai, Julian [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2005-07-01

Offshore pipelines have increasingly been operating at high temperatures and high pressures. Compression due to these loads can lead to global buckling, either laterally and/or vertically, depending on the burial depth and soil properties. The amount of embedment of pipelines directly laid on the seabed depends on the soil properties and influences the behavior of pipelines in operation. This work investigates the interaction between the vertical and lateral buckling modes, based on the analytical approach proposed for pipeline global buckling analysis by Hobbs. Furthermore, it presents a sensitivity study characterizing the impact of the determination of accurate soil properties. Finally, a conceptual design procedure, which takes into account the particular case of short pipelines, is provided. The method is presented by means of an example case. (author)

The Analysis of Factors Influencing Effectivenes of Property Taxes in Karanganyar Regency

Directory of Open Access Journals (Sweden)

Endang Brotojoyo

2018-03-01

Full Text Available The purpose of this study was to test empirically Effect of Compensation, Motivation and External Factors To Performance Officer With Property Taxes Voting in the District Effectiveness Matesih Karanganyar. The analysis technique used is using validity and reliability test, linearity test, regression analysis, path analysis, t test, F test, test the coefficient of determination and correlation analysis. Compensation Hypothesis Test Results significantly influence the effectiveness of tax collection. Motivation significantly influences the effectiveness of tax collection. External factors do not significant effect on effectiveness of tax collection. Compensation significant effect on the performance of Officers. Motivation significant effect on the performance of the Property Taxes polling clerk. External factors do not significant effect on the performance of Officers. Effectiveness of tax collection clerk significant effects on performance. F test results can be concluded jointly variable compensation, motivation, and external factors affecting the effectiveness of tax collection performance. The R2 total of 0,974 means that the performance of the Property Taxes in the district polling officer Matesih Karanganyar explained by the variable compensation, motivation, external factors and the effectiveness of tax collection amounted to 97.4%. The results of path analysis showed that the effective compensation and motivation through a direct path, while external factors are not effective for direct and indirect pathways.

Influence of Sugars, Modified Starches and Hydrocolloids Addition on Colour and Thermal Properties of Raspberry Cream Fillings

Directory of Open Access Journals (Sweden)

Pichler Anita

2017-03-01

Full Text Available This paper deals with the influence of the addition of sugars (sucrose, fructose and trehalose, modified starches (tapioca or waxy maize starch and hydrocolloids (karaya or guar gum on colour and thermal properties of raspberry cream fillings. In addition, the influence of the above-mentioned additives on the colour and thermal properties of raspberry cream fillings stored at room temperature over a period of 8 and 16 months was investigated. Results showed that the highest anthocyanin content and total phenolic content were detected in raspberry cream filling prepared with sucrose and trehalose in combination with guar gum. During storage, after 8 and 16 months at room temperature, anthocyanin content and total phenolic content decreased. Results also showed that the kind of sugar and added modified starches or hydrocolloids influenced the thermal properties of cream fillings. During storage, a decrease was observed in both freezing temperature as well as enthalpy of cream fillings.

Influence of condensed species on thermo-physical properties of LTE and non-LTE SF6-Cu mixture

Science.gov (United States)

Chen, Zhexin; Wu, Yi; Yang, Fei; Sun, Hao; Rong, Mingzhe; Wang, Chunlin

2017-10-01

SF6-Cu mixture is frequently formed in high-voltage circuit breakers due to the electrode erosion and metal vapor diffusion. During the interruption process, the multiphase effect and deviation from local thermal equilibrium (non-LTE assumption) can both affect the thermo-physical of the arc plasma and further influence the performance of circuit breaker. In this paper, thermo-physical properties, namely composition, thermodynamic properties and transport coefficients are calculated for multiphase SF6-Cu mixture with and without LTE assumption. The composition is confirmed by combining classical two-temperature mass action law with phase equilibrium condition deduced from second law of thermodynamics. The thermodynamic properties and transport coefficients are calculated using the multiphase composition result. The influence of condensed species on thermo-physical properties is discussed at different temperature, pressure (0.1-10 atm), non-equilibrium degrees (1-10), and copper molar proportions (0-50%). It is found that the multiphase effect has significant influence on specific enthalpy, specific heat and heavy species thermal conductivity in both LTE and non-LTE SF6-Cu system. This paper provides a more accurate database for computational fluid dynamic calculation.

The influence of aggregates type on W/C ratio on the strength and other properties of concrete

Science.gov (United States)

Malaiskiene, J.; Skripkiunas, G.; Vaiciene, M.; Karpova, E.

2017-10-01

The influence of different types of aggregates and W/C ratio on concrete properties is analysed. In order to achieve this aim, lightweight (with expanded clay aggregate) and normal concrete (with gravel aggregate) mixtures are prepared with different W/C ratios. Different W/C ratios are selected by reducing the amount of cement when the amount of water is constant. The following properties of concrete have been determined: density, compressive strength and water absorption. Additionally, the statistical data analysis is performed and influence of aggregate type and W/C ratio on concrete properties is determined. The empirical equations indicating dependence between concrete strength and W/C and strength of aggregate are obtained for normal concrete and light-weight concrete.

Experiments as to the influence of heat recovery from a bioreactor on sewage sludge disinfecting

Energy Technology Data Exchange (ETDEWEB)

Tarjanyi, J.; Strauch, D.; Philipp, W.

The influence of heat recovery on the disinfecting effect of composting of sewage sludge in a bio-reactor (in-vessel-composting) was investigated in a reactor type Weiss-system Kneer. As test agents 3 different serovars of salmonella, Parvo- and Poliovirus and eggs of Ascaris suum were used. The experiments were done in a reactor which was fed with dewatered municipal sewage sludge mixed with waste-paper as C-carrier for better composting. Even under winter conditions the test agents were inactivated within the time which is characteristic for the passage of the composting material through the plug-flow reactor. These results cannot simply be applied without further investigation to other reactors of the same type but with different ways of operation. (orig.)

Thermo physical properties of lateritic soil bricks: Influence of water content

International Nuclear Information System (INIS)

Meukam, P.; Noumowe, A.; Kofane, T.C.

2002-11-01

This paper presents an experimental study carried out in order to determine the properties of local materials used as construction materials. Cement stabilized compressed bricks were tested. The thermal properties of lateritic soil based materials were determined. The objectives of work reported in this paper are to determine the effect of addition of pozzolan or sawdust in lateritic soil brick on the thermal properties. It was shown that the effect of the incorporation of pozzolan or sawdust is the decreasing of the thermal conductivity and density. The moisture content of these materials can modify their thermal performance. Thus a study of the influence of the water content on the thermal conductivity k and the thermal diffusivity a is presented. The thermal conductivity, as a function of water content, increases rapidly between O% and 12% for lateritic soil. The thermal diffusivity curve presents a maximum for values of water content of 15% for lateritic soil and 8% for lateritic soil-pozzolan or lateritic soil- sawdust. (author)

Influence of gaseous annealing environment on the properties of indium-tin-oxide thin films

International Nuclear Information System (INIS)

Wang, R.X.; Beling, C.D.; Fung, S.; Djurisic, A.B.; Ling, C.C.; Li, S.

2005-01-01

The influence of postannealing in different gaseous environments on the optical properties of indiu-tin-oxide (ITO) thin films deposited on glass substrates using e-beam evaporation has been systematically investigated. It is found that the annealing conditions affect the optical and electrical properties of the films. Atomic force microscopy, x-ray diffraction, and x-ray photoemission spectroscopy (XPS) were employed to obtain information on the chemical state and crystallization of the films. These data suggest that the chemical states and surface morphology of the ITO film are strongly influenced by the gaseous environment during the annealing process. The XPS data indicate that the observed variations in the optical transmittance can be explained by oxygen incorporation into the film, decomposition of the indium oxide phases, as well as the removal of metallic In

Stressful Presentations: Mild Chronic Cold Stress in Mice Influences Baseline Properties of Dendritic Cells

Directory of Open Access Journals (Sweden)

Kathleen Marie Kokolus

2014-02-01

Full Text Available The ability of dendritic cells to stimulate and regulate T cells is critical to effective anti-tumor immunity. Therefore, it is important to fully recognize any inherent factors which may influence DC function under experimental conditions, especially in laboratory mice since they are used so heavily to study immune responses. Physiological stress is well recognized to impair several arms of immune protection. The goals of this report are to briefly summarize previous work revealing how DCs respond to various forms of physiologically relevant stress and to present new data highlighting the potential for chronic mild cold stress inherent in mice housed at standard ambient temperatures required for laboratory mice to influence baseline DCs properties. Since recent data from our group shows that CD8+ T cell function is altered by mild chronic cold stress and since DC function is crucial for CD8+ T cell activation, we wondered whether mild cold stress may also be influencing DC properties. We found increased numbers of splenic DCs (CD11c+ in cold stressed mice compared to mice housed at a thermoneutral temperature, which significantly reduces cold stress. However, many of the DCs which are expanded in cold stressed mice express an immature phenotype. We also found that antigen presentation and ability of splenocytes to activate T cells were impaired compared to that seen in DCs isolated from mice at thermoneutrality. The new data presented here strongly suggest that the housing temperature of mice can affect fundamental properties of DC function which in turn could be influencing the response of DCs to added experimental stressors or other treatments.

Influence of ageing treatment on microstructure, mechanical and bio-corrosion properties of Mg-Dy alloys.

Science.gov (United States)

Yang, Lei; Huang, Yuanding; Feyerabend, Frank; Willumeit, Regine; Kainer, Karl Ulrich; Hort, Norbert

2012-09-01

Mg-Dy alloys have shown to be promising for medical applications. In order to investigate the influence of ageing treatment on their mechanical and corrosion properties, three Mg-xDy alloys (x=10, 15, 20 wt%) were prepared. Their microstructure, mechanical and corrosion behavior were investigated. The results indicate that ageing at 250 °C has little influence on the mechanical and corrosion properties. In contrast, ageing at 200 °C significantly increases the yield strength, and reduces the ductility. After ageing at 200 °C, the corrosion rate of Mg-20Dy alloy increases largely in 0.9 wt% NaCl solution, but remains unchanged in cell culture medium. Copyright © 2012 Elsevier Ltd. All rights reserved.

Influence of heating rate and temperature firing on the properties of bodies of red ceramic

International Nuclear Information System (INIS)

Silva, B.J. da; Goncalves, W.P.; Cartaxo, J.M.; Macedo, R.S.; Neves, G.A.; Santana, L.N.L.; Menezes, R.R.

2011-01-01

In the red ceramic industry, the firing is one of the main stages of the production process. There are two heating rates prevailing at this stage: the slow (traditional ceramics) and fast. The slow rate more used in Brazil, is considered delayed. This study aims to evaluate the influence of particle size and chemical composition of three mixture of clay, used in the manufacture of red ceramic products and to study the influence of the firing temperature on their technological properties. When subjected to heating rates slow and fast. Initially, the mixtures were characterized subsequently were extruded, dried and subjected to firing at temperatures of 900 and 1000 ° C with heating rates of 5, 20 and 30 °C/min. The results indicated that the chemical composition and particle size influenced significantly the technological properties and that the bodies obtained with the paste that had lower levels of flux showed better stability. (author)

Influence of amino-functional macro and micro silicone softeners on the properties of cotton fabric

International Nuclear Information System (INIS)

Jatoi, A.W.; Khatri, Z.

2015-01-01

Amino-functional silicone softeners are most widely used type of soft finishes owing to their outstanding permanent softness, smoothness and handle characteristics. These soft finishes are prepared in different emulsion droplet sizes such as macro and micro emulsions providing varying characteristics on the textile on which they are applied. The macroemulsions due to their larger droplet sizes lubricate fabric and yarn surfaces, while the micro-emulsion, thanks to their smaller sizes penetrate inside fiber pores. In this research amino-functional macro and micro emulsions have been applied on dyed cotton fabric in 1:1 combination and compared against their influence on physical properties such as bending length, abrasion resistance, tensile strength, crease resistance and water repellency. These emulsions have also been compared for their influence on colorimetric properties; color difference and color strength (K/S values). The results reveal that the softener application in combination improves the properties deteriorated by each softener when applied separately. (author)

Influence of some crosslinking agents on thermal and mechanical properties of electron beam irradiated polylactide

Energy Technology Data Exchange (ETDEWEB)

Rytlewski, Piotr, E-mail: prytlewski@ukw.edu.p [Department of Materials Engineering, Kazimierz Wielki University, ul. Chodkiewicza 30, 85-064 Bydgoszcz (Poland); Malinowski, RafaL [Institute for Engineering of Polymer Materials and Dyes, ul. M. SkLodowskiej-Curie 55, 87-100 Torun (Poland); Moraczewski, Krzysztof [Department of Materials Engineering, Kazimierz Wielki University, ul. Chodkiewicza 30, 85-064 Bydgoszcz (Poland); Zenkiewicz, Marian [Institute for Engineering of Polymer Materials and Dyes, ul. M. SkLodowskiej-Curie 55, 87-100 Torun (Poland)

2010-10-15

The aim of this article was to determine and compare the influence of trimethylopropane trimethacylate (TMPTA) and trially isocyanurate (TAIC) crosslinking agents on thermal and mechanical properties of electron beam irradiated polylactide (PLA). The blends were made of PLA mixed with 3 wt% of TMPTA (PLA/TMPTA), and PLA mixed with 3 wt% of TAIC (PLA/TAIC). Injection moulded samples were irradiated with the use of high energy (10 MeV) electron beam at various radiation doses to crosslinking PLA macromolecules. Thermal and mechanical properties were investigated by means of differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), tensile strength, and impact strength measurements. The samples were also characterized by Fourier transform infrared spectroscopy (FTIR). It was found that under the influence of electron irradiation PLA/TMPTA samples underwent degradation while PLA/TAIC samples became crosslinked. Tensile and impact strengths of PLA/TMPTA samples decreased with increasing radiation dose while an enhancement of these properties for PLA/TAIC samples was observed.

Influence of some crosslinking agents on thermal and mechanical properties of electron beam irradiated polylactide

International Nuclear Information System (INIS)

Rytlewski, Piotr; Malinowski, RafaL; Moraczewski, Krzysztof; Zenkiewicz, Marian

2010-01-01

The aim of this article was to determine and compare the influence of trimethylopropane trimethacylate (TMPTA) and trially isocyanurate (TAIC) crosslinking agents on thermal and mechanical properties of electron beam irradiated polylactide (PLA). The blends were made of PLA mixed with 3 wt% of TMPTA (PLA/TMPTA), and PLA mixed with 3 wt% of TAIC (PLA/TAIC). Injection moulded samples were irradiated with the use of high energy (10 MeV) electron beam at various radiation doses to crosslinking PLA macromolecules. Thermal and mechanical properties were investigated by means of differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), tensile strength, and impact strength measurements. The samples were also characterized by Fourier transform infrared spectroscopy (FTIR). It was found that under the influence of electron irradiation PLA/TMPTA samples underwent degradation while PLA/TAIC samples became crosslinked. Tensile and impact strengths of PLA/TMPTA samples decreased with increasing radiation dose while an enhancement of these properties for PLA/TAIC samples was observed.

The impact of pumped water from a de-watered Magnesian limestone quarry on an adjacent wetland: Thrislington, County Durham, UK

International Nuclear Information System (INIS)

Mayes, W.M.; Large, A.R.G.; Younger, P.L.

2005-01-01

Although quarrying is often cited as a potential threat to wetland systems, there is a lack of relevant, quantitative case studies in the literature. The impact of pumped groundwater discharged from a quarry into a wetland area was assessed relative to reference conditions in an adjacent fen wetland that receives only natural runoff. Analysis of vegetation patterns at the quarry wetland site, using Detrended Correspondence Analysis and the species indicator values of Ellenberg, revealed a clear disparity between community transitions in the quarry wetland and the reference site. Limited establishment of moisture-sensitive taxa, the preferential proliferation of robust wetland species and an overall shift towards lower species diversity in the quarry wetland were explicable primarily by the physico-chemical environment created by quarry dewatering. This encompassed high pH (up to 12.8), sediment-rich effluent creating a nutrient-poor substrate with poor moisture retention in the quarry wetland, and large fluctuations in water levels. - High pH, sediment-rich runoff from a quarry constrains floristic diversity in an adjacent wetland

The impact of pumped water from a de-watered Magnesian limestone quarry on an adjacent wetland: Thrislington, County Durham, UK

Energy Technology Data Exchange (ETDEWEB)

Mayes, W.M. [Institute for Research on Environment and Sustainability, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom)]. E-mail: w.m.mayes@ncl.ac.uk; Large, A.R.G. [School of Geography, Politics and Sociology, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom); Younger, P.L. [Institute for Research on Environment and Sustainability, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom)

2005-12-15

Although quarrying is often cited as a potential threat to wetland systems, there is a lack of relevant, quantitative case studies in the literature. The impact of pumped groundwater discharged from a quarry into a wetland area was assessed relative to reference conditions in an adjacent fen wetland that receives only natural runoff. Analysis of vegetation patterns at the quarry wetland site, using Detrended Correspondence Analysis and the species indicator values of Ellenberg, revealed a clear disparity between community transitions in the quarry wetland and the reference site. Limited establishment of moisture-sensitive taxa, the preferential proliferation of robust wetland species and an overall shift towards lower species diversity in the quarry wetland were explicable primarily by the physico-chemical environment created by quarry dewatering. This encompassed high pH (up to 12.8), sediment-rich effluent creating a nutrient-poor substrate with poor moisture retention in the quarry wetland, and large fluctuations in water levels. - High pH, sediment-rich runoff from a quarry constrains floristic diversity in an adjacent wetland.

Observations of ebb flows on tidal flats: Evidence of dewatering?

Science.gov (United States)

Rinehimer, J. P.; Thomson, J. M.; Chickadel, C.

2010-12-01

Incised channels are a common morphological feature of tidal flats. When the flats are inundated, flows are generally forced by the tidally varying sea surface height. During low tide, however, these channels continue to drain throughout flat exposure even without an upstream source of water. While the role of porewater is generally overlooked due to the low permeability of marine muds, it remains the only potential source of flows through the channels during low tide. In situ and remotely sensed observations (Figure 1) at an incised channel on a tidal flat in Willapa Bay from Spring 2010 indicate that dewatering of the flats may be driving these low tide flows. High resolution Aquadopp ADCP velocity profiles are combined with observations from tower-based infrared (IR) video to produce a complete time series of surface velocity measurements throughout low tide. The IR video observations provide a measurement of surface currents even when the channel depth is below the blanking distance of the ADCP (10 cm). As the depth within the channel drops from 50 cm to 10 cm surface velocities increase from 10 cm/s to 60 cm/s even as the tide level drops below the channel flanks and the flats are dry. As the drainage continues, the temperature of the flow rises throughout low tide, mirroring temperatures within the sediment bed on the tidal flat. Drainage salinity falls despite the lack of any freshwater input to the flat indicating that less saline porewater may be the source. The likely source of the drainage water is from the channel flanks where time-lapse video shows slumping and compaction of channel sediments. Velocity profiles, in situ temperatures, and IR observations also are consistent with the presence of fluid muds and a hyperpycnal, density driven outflow at the channel mouth highlighting a possible pathway for sediment delivery from the flats to the main distributary channels of the bay. Figure 1: Time series of tidal flat channel velocities and temperatures

Gamma irradiation influence on physical properties of milk proteins

International Nuclear Information System (INIS)

Ciesla, K.; Salmieri, S.; Lacroix, M.; Le Tien, C.

2004-01-01

Gamma irradiation was found to be an effective method for the improvement of both barrier and mechanical properties of the edible films and coatings based on calcium and sodium caseinates alone or combined with some globular proteins. Our current studies concern gamma irradiation influence on the physical properties of calcium caseinate-whey protein isolate-glycerol (1:1:1) solutions and gels, used for films preparation. Irradiation of solutions was carried out with Co-60 gamma rays applying 0 and 32 kGy dose. The increase in viscosity of solutions was found after irradiation connected to induced crosslinking. Lower viscosity values were detected, however, after heating of the solutions irradiated with a 32 kGy dose than after heating of the non-irradiated ones regarding differences in the structure of gels and resulting in different temperature-viscosity curves that were recorded for the irradiated and the non-irradiated samples during heating and cooling. Creation of less stiff but better ordered gels after irradiation arises probably from reorganisation of aperiodic helical phase and β-sheets, in particular from increase of β-strands, detected by FTIR. Films obtained from these gels are characterised by improved barrier properties and mechanical resistance and are more rigid than those prepared from the non-irradiated gels. The route of gel creation was investigated for the control and the irradiated samples during heating and the subsequent cooling

Gamma irradiation influence on physical properties of milk proteins

Energy Technology Data Exchange (ETDEWEB)

Ciesla, K. E-mail: kciesla@orange.ichtj.waw.pl; Salmieri, S.; Lacroix, M.; Le Tien, C

2004-10-01

Gamma irradiation was found to be an effective method for the improvement of both barrier and mechanical properties of the edible films and coatings based on calcium and sodium caseinates alone or combined with some globular proteins. Our current studies concern gamma irradiation influence on the physical properties of calcium caseinate-whey protein isolate-glycerol (1:1:1) solutions and gels, used for films preparation. Irradiation of solutions was carried out with Co-60 gamma rays applying 0 and 32 kGy dose. The increase in viscosity of solutions was found after irradiation connected to induced crosslinking. Lower viscosity values were detected, however, after heating of the solutions irradiated with a 32 kGy dose than after heating of the non-irradiated ones regarding differences in the structure of gels and resulting in different temperature-viscosity curves that were recorded for the irradiated and the non-irradiated samples during heating and cooling. Creation of less stiff but better ordered gels after irradiation arises probably from reorganisation of aperiodic helical phase and {beta}-sheets, in particular from increase of {beta}-strands, detected by FTIR. Films obtained from these gels are characterised by improved barrier properties and mechanical resistance and are more rigid than those prepared from the non-irradiated gels. The route of gel creation was investigated for the control and the irradiated samples during heating and the subsequent cooling.

Influence of sputtering power on the optical properties of ITO thin films

Energy Technology Data Exchange (ETDEWEB)

K, Aijo John; M, Deepak, E-mail: manju.thankamoni@gmail.com; T, Manju, E-mail: manju.thankamoni@gmail.com [Department of Physics, Sree Sankara College, Kalady P. O., Ernakulam Dist., Kerala (India); Kumar, Vineetha V. [Dept. of Physics, K. E. College, Mannanam, Kottayam Dist., Kerala (India)

2014-10-15

Tin doped indium oxide films are widely used in transparent conducting coatings such as flat panel displays, crystal displays and in optical devices such as solar cells and organic light emitting diodes due to the high electrical resistivity and optical transparency in the visible region of solar spectrum. The deposition parameters have a commendable influence on the optical and electrical properties of the thin films. In this study, ITO thin films were prepared by RF magnetron sputtering. The properties of the films prepared under varying sputtering power were compared using UV- visible spectrophotometry. Effect of sputtering power on the energy band gap, absorption coefficient and refractive index are investigated.

Influence of fly-ashes on properties of ordinary concretes

Directory of Open Access Journals (Sweden)

Rutkowska Gabriela

2016-03-01

Full Text Available Influence of fly-ashes on properties of ordinary concretes. Care of the environment in accordance with the principles of sustainable development introduces the possibility and need for waste recycling. The construction and building materials industry has the greatest potential for reuse of waste. The article presents the results of investigations of selected properties (consistency, water absorbability, compressive strength and tensile strength after 28 and 56 days of curing, depth of penetration of ordinary concretes and concretes containing fly-ashes - calcareous and siliceous ash − in their composition. To make the samples, the Portland cement CEM I 42.5 R and natural aggregate with graining of 0-16 mm were used. The concrete with siliceous and calcareous admixtures was made in three lots where the ash was added in the quantity of 15, 20 and 30% of the cement mass. After the tests, it was stated that the fly-ash admixture does not increase the air content in the mix, it increases the compressive strength in time and the siliceous ash improves the splitting tensile strength.

Experimental study on influence of carbon dioxide on porous structure and mechanical properties of shale rock

Directory of Open Access Journals (Sweden)

Danuta Miedzińska

2017-12-01

Full Text Available Shale rocks are geological formations which can be unconventional gas reservoirs. During their interaction with carbon dioxide, which can be used as a fracturing fluid in shale gas recovery process, many phenomena take place that can influence rock structure and mechanical properties. The research on changes in rock structure under super critical carbon dioxide interaction and their influence of shale properties were presented in the paper. The structural tests were carried out with the use of microscopic techniques with different resolutions of visualization. The uniaxial compression test was applied as a mechanical properties’ assessment experiment. As a result of research, some dependence was observed. The bigger decrease was in porosity after infiltration in lower zooms, the bigger increase in porosity in high zooms and mechanical properties was noticed. Keywords: geomechanics, shale rock, carbon dioxide

Rock properties influencing impedance spectra (IS) studied by lab measurements on porous model systems

Energy Technology Data Exchange (ETDEWEB)

Volkmann, J.; Klitzsch, N.; Mohnke, O. [RWTH Aachen Univ. (Germany). Applied Geophysics and Geothermal Energy; Schleifer, N. [Wintershall Holding GmbH, Barnstorf (Germany)

2013-08-01

The wetting condition of reservoir rocks is a crucial parameter for the estimation of reservoir characteristics like permeability and saturation with residual oil or water. Since standard methods are often costly, at least in terms of time, we aim at assessing wettability of reservoir rocks using impedance spectroscopy (IS), a frequency dependent measurement of complex electric resistivity. This approach is promising, because IS is sensitive to the electrochemical properties of the inner surface of rocks which, on the other hand, are decisively influencing wettability. Unfortunately, there is large number of rock parameters - besides wettability - influencing the impedance spectra often not exactly known for natural rock samples. Therefore, we study model systems to improve the understanding of the underlying mechanisms and to quantify the influencing parameters. The model systems consist of sintered porous silica beads of different sizes leading to samples with different pore sizes. The main advantage of these samples compared to natural rocks is their well-defined and uniform mineralogical composition and thus their uniform electrochemical surface property. In order to distinguish pore geometry and fluid electrochemistry effects on the IS properties we measured the IS response of the fully water saturated model systems in a wide frequency range - from 1 mHz to 35 MHz - to capture different often overlapping polarization processes. With these measurements we study the influence of pore or grain size, fluid conductivity, and wettability (contact angle) on the impedance spectra. The influence of wettability was studied by modifying the originally hydrophilic inner surface into a hydrophobic state. The wettability change was verified by contact angle measurements. As results, we find pore size dependent relaxation times and salinity dependent chargeabilities for the hydrophilic samples in the low frequency range (< 10 kHz), whereas for the hydrophobic samples

Influence of bending deflection rate on properties of fibrous mortar

Directory of Open Access Journals (Sweden)

Metwally Abd Allah Abd el Aty

2013-04-01

Full Text Available Selection of the construction materials is affected by many factors including their properties under the applied loads. Loading rate is considered as a very important parameter which influences the behavior of the materials. Fibrous concrete is commonly used in applications in which the loading rate exceeds quasi static conditions by a large margin. This paper investigates the influence of flexural loading rate on the performance of fibrous concrete prisms in flexure. Two hundred and fifty two prisms include fibrous concrete and control specimens were prepared and tested. Fiber type, fiber dosage and flexural loading rate were the main parameters considered in this study. Two types of fibers were investigated namely polypropylene fibers and glass fibers. Three dosages of fiber volume fractions were implemented as 0.5%, 1.0% and 2.0%. A total of 12 different rates of displacement (0.0039 up to 8 mm/s for load application were conducted. A computer controlled universal testing machine provided with data acquisition system capable of performing 1000 loop per second was used. Load–central deflection, flexural strength and toughness were the evaluated properties for the investigated specimens. The results indicated that the flexure strength values exhibited loading rate dependence not only for the control mix but also for the investigated fibrous mortar mixes. Also the performance in flexure varied substantially not only with loading rate but with fiber type and fiber volume fractions as well.

Influence of yarn folding on UV protection properties of hemp knitted fabrics

Directory of Open Access Journals (Sweden)

Kocić Ana A.

2016-01-01

Full Text Available In the last years the media have highlighted the damage of the ozone layer and the resulting increase of ultraviolet radiation (UVR reaching the earth’s surface. Prolonged and repeated, both occupational and recreational, sun exposure of the population causes some detrimental effects. Clothing is considered to be one of the most important tools for UV protection. It is generally accepted that synthetic fibres provide a high UV protection capability of textiles, while cellulose fibres (cotton, linen, hemp, viscose have a low UV absorption capacity. However, natural pigments, pectin and waxes in natural cellulose fibers, and lignin in hemp fibers, act as UV absorbers having a favorable effect on UPF of grey-state fabrics. Bearing in mind the trend of reintroduction of hemp fibers as a source of eco-friendly textiles, there is a serious lack of study about the potential of hemp materials in terms of UV protection. Folded yarn is a complex yarn composed of two or more component yarns arranged parallel and twisted together to make a “new quality” yarn. Folding of yarns is an operation undertaken in order to modify single-yarn properties to an appreciable degree. There are very few investigations concerning the relationship between the yarn properties and UV protection effectiveness of the fabric made there from. In addition, there is no any result in the scientific literature about the influence of yarn folding on UV protection properties of textile materials. Having this in mind, for our research the idea was to evaluate the effect of yarn folding in this regard. The plain knitted fabrics composed of single or two-folded hemp yarn were compared in terms of UV protection properties. The Ultraviolet Protection Factor (UPF, as the quantitative measurement of the material effectiveness to protect the human skin against UVR, was determined for the textile materials by in vitro test method according to the European standard EN 13758. The knitted

The influence of surface functionalisation on the electrical properties and thermal stability of nanodiamonds

Energy Technology Data Exchange (ETDEWEB)

Welch, Joseph O; Li, Pei; Chaudhary, Aysha; Edgington, Robert; Jackman, Richard B., E-mail: r.jackman@ucl.ac.uk [London Centre for Nanotechnology and the Department of Electronic and Electrical Engineering, University College London, 17-19 Gordon Street, London WC1H 0AH (United Kingdom)

2014-10-07

Detonation nanodiamond (ND) has recently emerged as a useful new class of diamond material. However, to date there has been little investigation of the electrical properties of this material. Due to the nanoscale dimensions, the surface functionalisation of the individual ND is of particular importance to the characteristics of ND films. Here, hydrogen and oxygen termination of ND, verified using Fourier transform infrared spectroscopy, are shown to strongly influence the electronic properties of NDs. Hydrogen terminated ND exhibiting a far greater resilience to thermal decomposition when compared to the oxygen terminated NDs. Moreover, H-NDs also displayed so-called “surface conductivity,” a property displayed by hydrogen-terminated bulk diamond films, whilst O-NDs display properties high resistivity. These results indicate that under the correct conditions ND layers can display similar electrical properties to “bulk” diamond thin films.

Influence of molybdenum on the creep properties of nickel-base superalloy single crystals

Science.gov (United States)

Mackay, R. A.; Nathal, M. V.; Pearson, D. D.

1990-01-01

The Mo content of an alloy series based on Ni-6 wt pct Al-6 wt pct Ta was systematically varied from 9.8 to 14.6 wt pct, in order to ascertain the influence of Mo on the creep properties of single crystals. The optimum initial gamma-gamma prime microstructure for raft development and creep strength was established in each alloy before testing. It was found that, as the Mo content increased from 9.8 to 14.0 percent, the magnitude of the lattice mismatch increased; upon reaching 14.6 percent, a degradation of mechanical properties occurred due to the precipitation of a third phase. These results suggest that small refractory metal content and initial gamma-prime variations can profoundly affect mechanical properties.

Influence of short range ordering and clustering on transport properties

International Nuclear Information System (INIS)

Vigier, G.; Pelletier, J.M.

1982-01-01

The influence of short range ordering and clustering phenomena on the electrical resistivity p and the thermopower S is investigated both theoretically and experimentally. According to the considered alloys either increases or decreases of transport properties may be observed when deviations from a random distribution of solute atoms occur. These observations are explained with a model based on free electrons and Born approximations the importance of the potential choice is underlined; two kinds of description of the structure factor are investigated. A good semiquantitative agreement is obtained between computed results and experimental observations

Influence of the Category Discharge Processing on Strength Properties of Piezocomposites

International Nuclear Information System (INIS)

Ramazanov, M. A.

2006-01-01

Piezoelectric, dielectric and physicomechanical properties of polymeric piezocomposites on piezoceramics basis are one of the major operational devices of applications. During their application in various devices for a long time can be exposed to various influences for a long time. Piezoelectric, dielectric and strength properties of polymeric piezocomposites strongly depend from the interphase phenomena, and also on charges saved up on border of the unit between components of a composition. Therefore creation the preliminary centers localization for charges in a composition is an actual problem for development effective polymeric piezocomposites. In the given work results of a research preliminary discharge processing's of powders of polymer on strength properties and dielectric characteristics of polymeric compositions on a basis polyvinilidenftorid (PVDF), high density polyethylene and piezoceramic from tetragonal structure are poisoned. Piezoceramic had structure plumbum-zirconate-titanate (PZT). Powders of polymer have been subjected to discharge processing in a quartz glass tube with a diameter 15 mm which walls with 1 mm. It is earthed, from one end and to other end it is connected with high-voltage electrode. Compositions in a volumetric ratio of 90+10 % have been obtained at temperature 435Κ under pressure 15ΜΠa. After creation reception of samples they were exposed electrothermopolarization. It is experimentally established, that after discharge processing powders of polymer depending on of processing duration electric and mechanical durability, and also an accrued charge on border of the unit of phases up to the certain value increases, and then decreases. Also it is shown, hat influence of category processing on strength and dielectric characteristics of a composition on the basis of polymer PVDF is more than , has on polyethylene basis. Changes piezoelectric, dielectric it is supposed, that, and strength properties to an extreme piezocomposite

Influence of the Mould Cooling Process on the Quality and Properties of Aluminium Alloy

Directory of Open Access Journals (Sweden)

Viktorie Weiss

2014-12-01

Full Text Available The article deals with the effect on the quality of casting moulds (metal, bentonite mixture on the structure of the alloy AlZn5,5MgCu and selected mechanical properties of the alloy. The effect of foundry moulds can significantly affect formation and range of crystal segregation and the subsequent thermal process of homogenization which has an influence on the final quality of the alloy. The research focuses on the formation and range of crystal segregation and its removal with homogenization annealing, in which the observed influence of individual factors influencing the diffusion process and quality of the aluminium alloy.

Investigation of the influence of different cutting procedures on the global and local magnetic properties of non-oriented electrical steel

International Nuclear Information System (INIS)

Naumoski, H.; Riedmüller, B.; Minkow, A.; Herr, U.

2015-01-01

The process of manufacturing iron cores for electric machines out of electrical steel sheets can strongly affect the magnetic properties of the material. In order to better understand the influence of cutting on the iron losses, a characterization of the magnetization behavior near the cutting edge is needed. The local magnetic properties of the material are modified by the cutting process which leads to an increase in the iron losses measured for 5 mm wide ring core samples by nearly 160% at low inductions. We present investigations on the effect of cutting by observation of the magnetic domain structure of 0.35 mm thick non-oriented electrical steel. By using the magneto-optical Kerr-effect on a ring samples the local magnetic properties of the material after processing are characterized in the form of domain wall displacements under an applied external ac-field. The influence of various cutting techniques on the magnetic properties was studied before and after stress relief annealing. This method allows a quantitative analysis of the influence of different cutting techniques on the micro-magnetic properties of non-oriented electrical steel for rotating machines. - Highlights: • The influence of cutting on the magnetic properties of electrical steel was studied. • The magnetic behavior at the cut edge was investigated using the Kerr-effect. • The micro-magnetic results correlate well with the integral magnetic measurements. • Stress relief annealing recovers the magnetic properties of the cut material. • The method allows quantitative determination of the extension of the affected zone

Influence of surface finish on fatigue properties of metallic materials: a bibliographic study

International Nuclear Information System (INIS)

Akamatsu, M.

1997-01-01

The investigation of a fatigue failed component very often shows that cracks initiated at the surface. It is actually well known that the surface finish notably influences the fatigue strength of a component. We have carried out a bibliographic study in order to clarify the influence of the different surface parameters. The analysis of the literature has shown that most of the data concerns high cycle fatigue. Three aspects of the surface finish have been examined: geometry (roughness), residual stresses and microstructure. In a general way, the influence of geometrical surface finish is tackled either empirically, with a factor assessing the fatigue limit decrease when the roughness and the tensile strength increase, or theoretically, with approaches modelling geometrical irregularities as notches or cracks. In all cases, the effect of roughness on fatigue strength depends on the material, through mechanical properties or microstructural features. The theoretical approaches seem particularly interesting, but their use is not straightforward and requires further development. The creation of residual stresses at the surface of a component can just as well reduce as improve its fatigue strength. In a first approach, these stresses can be regarded as a mean service stress. In fact, mechanical and metallurgical gradients near the surface have to be taken into account, which affect the relaxation of residual stresses during fatigue cycling. Actually, the effect of residual stresses can hardly be isolated, because these stresses are associated with geometrical and microstructural modifications. Microstructural features (metallurgical structure, grain size, inclusions, strain hardening) have an undoubted influence on fatigue strength, but the quantification of the effects remains tricky. The influence of the microstructure of surface layers on fatigue strength generally depends on the mechanical properties of materials. In short, fatigue strength predictions through a

Influence Al doped ZnO nanostructure on structural and optical properties

International Nuclear Information System (INIS)

Ramelan, Ari Handono; Wahyuningsih, Sayekti; Chasanah, Uswatul; Munawaroh, Hanik

2016-01-01

The preparation of Al-doped ZnO (AZO) thin films prepared by the spin-coating method was reported. Preparation of AZO was conducted by annealing treatment at a temperature of 700°C. While the spin-coating process of AZO thin films were done at 2000 and 3000 rpm respectively. The structural properties of ZnO were determined by X- ray diffraction (XRD) analysis. ZnOnanostructure was formed after annealed at atemperature of 400°C.The morphology of ZnO was determined by Scanning Electron Microscopy (SEM) showed the irregular morphology about 30-50µm in size. Al doped on ZnO influenced the optical properties of those material. Increasing Al contain on ZnO cause of shifting to the lower wavelength. The optical properties of the ZnO as well as AZO films showed that higher reflectance on the ultraviolet region so those materials were used as anti-reflecting agent.Al addition significantly enhance the optical transparency and induce the blue-shift in optical bandgap of ZnO films.

Influence of condensed species on thermo-physical properties of LTE and non-LTE SF6–Cu mixture

International Nuclear Information System (INIS)

Chen, Zhexin; Wu, Yi; Yang, Fei; Sun, Hao; Rong, Mingzhe; Wang, Chunlin

2017-01-01

SF 6 –Cu mixture is frequently formed in high-voltage circuit breakers due to the electrode erosion and metal vapor diffusion. During the interruption process, the multiphase effect and deviation from local thermal equilibrium (non-LTE assumption) can both affect the thermo-physical of the arc plasma and further influence the performance of circuit breaker. In this paper, thermo-physical properties, namely composition, thermodynamic properties and transport coefficients are calculated for multiphase SF 6 –Cu mixture with and without LTE assumption. The composition is confirmed by combining classical two-temperature mass action law with phase equilibrium condition deduced from second law of thermodynamics. The thermodynamic properties and transport coefficients are calculated using the multiphase composition result. The influence of condensed species on thermo-physical properties is discussed at different temperature, pressure (0.1–10 atm), non-equilibrium degrees (1–10), and copper molar proportions (0–50%). It is found that the multiphase effect has significant influence on specific enthalpy, specific heat and heavy species thermal conductivity in both LTE and non-LTE SF 6 –Cu system. This paper provides a more accurate database for computational fluid dynamic calculation. (paper)

The Atmospheric Radiation Measurement Program May 2003 Intensive Operations Period Examining Aerosol Properties and Radiative Influences: Preface to Special Section

Science.gov (United States)

Ferrare, Richard; Feingold, Graham; Ghan, Steven; Ogren, John; Schmid, Beat; Schwartz, Stephen E.; Sheridan, Pat

2006-01-01

Atmospheric aerosols influence climate by scattering and absorbing radiation in clear air (direct effects) and by serving as cloud condensation nuclei, modifying the microphysical properties of clouds, influencing radiation and precipitation development (indirect effects). Much of present uncertainty in forcing of climate change is due to uncertainty in the relations between aerosol microphysical and optical properties and their radiative influences (direct effects) and between microphysical properties and their ability to serve as cloud condensation nuclei at given supersaturations (indirect effects). This paper introduces a special section that reports on a field campaign conducted at the Department of Energy Atmospheric Radiation Measurement site in North Central Oklahoma in May, 2003, examining these relations using in situ airborne measurements and surface-, airborne-, and space-based remote sensing.

Rheological properties of wheat starch influenced by amylose-lysophosphatidylcholine complexation at different gelation phases

NARCIS (Netherlands)

Ahmadiabhari, Salomeh; Woortman, Albert; Hamer, Rob; Loos, Katja

2015-01-01

Amylose is able to form helical inclusion complexes with lysophosphatidylcholine (LPC). This complexation influences the functional and rheological properties of wheat starch; however it is well known that the formation of these complexes lead the starchy systems to a slower enzymatic hydrolysis.

Rheological properties of wheat starch influenced by amylose-lysophosphatidylcholine complexation at different gelation phases

NARCIS (Netherlands)

Ahmadi-Abhari, S.; Woortman, A.J.J.; Hamer, R.J.; Loos, K.

2015-01-01

Amylose is able to form helical inclusion complexes with lysophosphatidylcholine (LPC). This complexation influences the functional and rheological properties of wheat starch; however it is well known that the formation of these complexes lead the starchy systems to a slower enzymatic hydrolysis.

Influence of electron beam irradiation on the impact properties of polystyrene/EPDM rubber blends

NARCIS (Netherlands)

Gisbergen, van J.G.M.; Sanden, van der M.C.M.; Haan, de J.W.; Ven, van de L.J.M.; Lemstra, P.J.

1991-01-01

The influence of electron beam (EB) irradiation on the impact properties of compatibilized polystyrene/ethylene-propylene-diene-monomer (PSIEPDM) blends was studied. The change in impact value upon irradiation proved to be strongly dependent on the type of compatibilizer used. Using a

Influence of viscoelastic property on laser-generated surface acoustic waves in coating-substrate systems

International Nuclear Information System (INIS)

Sun Hongxiang; Zhang Shuyi; Xu Baiqiang

2011-01-01

Taking account of the viscoelasticity of materials, the pulsed laser generation of surface acoustic waves in coating-substrate systems has been investigated quantitatively by using the finite element method. The displacement spectra of the surface acoustic waves have been calculated in frequency domain for different coating-substrate systems, in which the viscoelastic properties of the coatings and substrates are considered separately. Meanwhile, the temporal displacement waveforms have been obtained by applying inverse fast Fourier transforms. The numerical results of the normal surface displacements are presented for different configurations: a single plate, a slow coating on a fast substrate, and a fast coating on a slow substrate. The influences of the viscoelastic properties of the coating and the substrate on the attenuation of the surface acoustic waves have been studied. In addition, the influence of the coating thickness on the attenuation of the surface acoustic waves has been also investigated in detail.

Beyond the Alphabet Soup: Molecular Properties of Aerosol Components Influence Optics. (Invited)

Science.gov (United States)

Thompson, J. E.

2013-12-01

Components within atmospheric aerosols exhibit almost every imaginable model of chemical bonding and physical diversity. The materials run the spectrum from crystalline to amorphous, covalent to ionic, and have varying viscosities, phase, and hygroscopicity. This seminar will focus on the molecular properties of materials that influence the optical behavior of aerosols. Special focus will be placed on the polarizability of materials, hygroscopic growth, and particle phase.

Factors That Influence the Extensional Rheological Property of Saliva.

Directory of Open Access Journals (Sweden)

Amrita Vijay

Full Text Available The spinnbarkeit of saliva reflects the ability of saliva to adhere to surfaces within the mouth, thereby serving as a protective role and aiding in lubrication. Therefore, alterations in the extensional rheology of saliva may result in the loss in adhesiveness or the ability to bind onto surfaces. Mucin glycoproteins and their structures are known to be important factors for the extensional rheological properties of saliva. The conformation of mucin depends on factors such as pH and ionic strength. Chewing is one of the main stimuli for salivary secretion but creates significant sheer stress on the salivary film which could influence mouthfeel perceptions. The current study investigates the possible factors which affect the extensional rheological properties of saliva by comparing submandibular/sublingual saliva with different oral stimuli within the same group of subjects. Unstimulated and stimulated saliva (chew, smell and taste salivas were collected primarily from submandibular/sublingual glands. The saliva samples were measured for Spinnbarkeit followed by the measuring mucin, total protein, total calcium and bicarbonate concentrations. The results indicated correlations between rheological properties and mucin/ion concentrations. However, chewing stimulated submandibular/sublingual saliva is shown to have significantly lower Spinnbarkeit, but factors such as mucin, protein and calcium concentrations did not account for this variation. Analysis of the concentration of bicarbonate and pH appears to suggest that it has a prominent effect on extensional rheology of saliva.

The Influence of Forming Directions and Strain Rate on Dynamic Shear Properties of Aerial Aluminum Alloy

Directory of Open Access Journals (Sweden)

Ying Meng

2018-03-01

Full Text Available Dynamic shear properties under high strain rate are an important basis for studying the dynamic mechanical properties and microscopic mechanisms of materials. Dynamic impact shear tests of aerial aluminum alloy 7050-T7451 in rolling direction (RD, transverse direction (TD and normal direction (ND were performed at a range of strain rates from 2.5 × 104 s−1 to 4.5 × 104 s−1 by High Split Hopkinson Pressure Bar (SHPB. The influence of different forming directions and strain rates on the dynamic shear properties of material and the microstructure evolution under dynamic shear were emphatically analyzed. The results showed that aluminum alloy 7050-T7451 had a certain strain rate sensitivity and positive strain rate strengthening effect, and also the material had no obvious strain strengthening effect. Different forming directions had a great influence on dynamic shear properties. The shear stress in ND was the largest, followed by that in RD, and the lowest was that in TD. The microstructure observation showed that the size and orientation of the grain structure were different in three directions, which led to the preferred orientation of the material. All of those were the main reasons for the difference of dynamic shear properties of the material.

Influence of polymer fibers on rheological properties of cement mortars

Directory of Open Access Journals (Sweden)

Malaszkiewicz Dorota

2017-10-01

Full Text Available The reinforcing effect of fibers in cement composites often results in the improvement of the brittle nature of cementitious materials. But the decrease in the workability of fresh concrete is often the disadvantage of fibers addition. Conventional single-point workability tests cannot characterize workability of concrete in terms of fundamental rheological parameters. To this end, this paper describes an investigation of the influence of synthetic fiber additions (fiber length in the range 12–50 mm and volume fraction in the range 0–4% on the rheological properties of fiber reinforced fresh mortar (FRFM and development of these properties over time. The rheometer Viskomat XL was used in this study. Within the limitations of the instrument and testing procedure it is shown that FRFMs conform to the Bingham model. Natural postglacial sand 0/4 mm was used as a fine aggregate and cement CEMI 42.5 R was used as a binder. Three commercial synthetic fibers were selected for these examinations. Rheological properties were expressed in terms of Bingham model parameters g (yield value and h (plastic viscosity. Based on the test results it was found out that the fiber type and volume fraction affected both the yield stress and plastic viscosity.

Influence of polymer fibers on rheological properties of cement mortars

Science.gov (United States)

Malaszkiewicz, Dorota

2017-10-01

The reinforcing effect of fibers in cement composites often results in the improvement of the brittle nature of cementitious materials. But the decrease in the workability of fresh concrete is often the disadvantage of fibers addition. Conventional single-point workability tests cannot characterize workability of concrete in terms of fundamental rheological parameters. To this end, this paper describes an investigation of the influence of synthetic fiber additions (fiber length in the range 12-50 mm and volume fraction in the range 0-4%) on the rheological properties of fiber reinforced fresh mortar (FRFM) and development of these properties over time. The rheometer Viskomat XL was used in this study. Within the limitations of the instrument and testing procedure it is shown that FRFMs conform to the Bingham model. Natural postglacial sand 0/4 mm was used as a fine aggregate and cement CEMI 42.5 R was used as a binder. Three commercial synthetic fibers were selected for these examinations. Rheological properties were expressed in terms of Bingham model parameters g (yield value ) and h (plastic viscosity). Based on the test results it was found out that the fiber type and volume fraction affected both the yield stress and plastic viscosity.

Nitrogen dynamics model for a pilot field-scale novel dewatered alum sludge cake-based constructed wetland system.

Science.gov (United States)

Kumar, J L G; Zhao, Y Q; Hu, Y S; Babatunde, A O; Zhao, X H

2015-01-01

A model simulating the effluent nitrogen (N) concentration of treated animal farm wastewater in a pilot on-site constructed wetland (CW) system, using dewatered alum sludge cake (DASC) as wetland substrate, is presented. The N-model was developed based on the Structural Thinking Experiential Learning Laboratory with Animation software and is considering organic nitrogen, ammonia nitrogen (NH3) and nitrate nitrogen (NO3-N) as the major forms of nitrogen involved in the transformation chains. Ammonification (AMM), ammonia volatilization, nitrification (NIT), denitrification, plant uptake, plant decaying and uptake of inorganic nitrogen by algae and bacteria were considered in this model. pH, dissolved oxygen, temperature, precipitation, solar radiation and nitrogen concentrations were considered as forcing functions in the model. The model was calibrated by observed data with a reasonable agreement prior to its applications. The simulated effluent detritus nitrogen, NH4-N, NO3-N and TN had a considerably good agreement with the observed results. The mass balance analysis shows that NIT accounts for 65.60%, adsorption (ad) (11.90%), AMM (8.90%) followed by NH4-N (Plants) (5.90%) and NO3-N (Plants) (4.40%). The TN removal was found 52% of the total influent TN in the CW. This study suggested an improved overall performance of a DASC-based CW and efficient N removal from wastewater.

The influence of Pt redistribution on Ni1-xPtxSi growth properties

International Nuclear Information System (INIS)

Demeulemeester, J.; Smeets, D.; Temst, K.; Vantomme, A.; Comrie, C. M.; Van Bockstael, C.; Knaepen, W.; Detavernier, C.

2010-01-01

We have studied the influence of Pt on the growth of Ni silicide thin films by examining the Pt redistribution during silicide growth. Three different initial Pt configurations were investigated, i.e., a Pt alloy (Ni+Pt/ ), a Pt capping layer (Pt/Ni/ ) and a Pt interlayer (Ni/Pt/ ), all containing 7 at. % Pt relative to the Ni content. The Pt redistribution was probed using in situ real-time Rutherford backscattering spectrometry (RBS) whereas the phase sequence was monitored during the solid phase reaction (SPR) using in situ real-time x-ray diffraction. We found that the capping layer and alloy exhibit a SPR comparable to the pure Ni/ system, whereas Pt added as an interlayer has a much more drastic influence on the Ni silicide phase sequence. Nevertheless, for all initial sample configurations, Pt redistributes in an erratic way. This phenomenon can be assigned to the low solubility of Pt in Ni 2 Si compared to NiSi and the high mobility of Pt in Ni 2 Si compared to pure Ni. Real-time RBS further revealed that the crucial issue determining the growth properties of each silicide phase is the Pt concentration at the Si interface during the initial stages of phase formation. The formation of areas rich in Pt reduce the Ni silicide growth kinetics which influences the phase sequence and properties of the silicides.

Time Course of Influence by Ovariectomy and Calcium Diet on Bone Properties in Mice

OpenAIRE

Minematsu, Akira; Yoshimura, Osamu; Yotsuji, Hirofumi; Ichigo, Hirozo; Kobayashi, Ryuji; Sasaki, Hisato; Tanaka, Sachiko; Kanemura, Naohiko; Shirahama, Kunji; Miyamoto, Hidetaka

2001-01-01

This study was investigated the influence by ovariectomy (OVX) and calcium diet on bone properties in eighty-one female ICR strain mice with age of 5 weeks. The animals were randomly assigned to sham operation (SHAM), OVX, SHAM+low Ca intake (L.Ca) and OVX+L.Ca group. They were euthanized with lethal dose of pentobarbital sodium at day 50, 100 and 140 post-operatively. For determining the bone properties, both femur and tibial bones were excised from the hind limb, and removed off surrounding...

Influence of different ions doping on the antibacterial properties of MgO nanopowders

Energy Technology Data Exchange (ETDEWEB)

Rao, Yuanyuan; Wang, Wei, E-mail: weiwang@hust.edu.cn; Tan, Fatang; Cai, Yuncheng; Lu, Junwen; Qiao, Xueliang

2013-11-01

Compared with other inorganic antibacterial agents, magnesium oxide (MgO) nanopowders exhibit a unique antibacterial mechanism and various advantages in applications, having attracted extensive attention. In this study, MgO nanopowders doped with different ions (Li{sup +}, Zn{sup 2+} and Ti{sup 4+}) were synthesized by a sol–gel method, respectively. The structures and morphologies of the as-obtained precursors and nanopowders were characterized and confirmed by X-ray diffraction (XRD), transmission electron microscope (TEM) and X-ray photoelectron spectroscopy (XPS) analysis. The influence of three metal ions doping on the antibacterial properties of MgO nanopowders was also investigated by their bactericidal activity against Escherichia coli (E. coli, ATCC 25922) using the broth microdilution method and the agar method. The results show that Li-doped MgO exhibits better antibacterial activity, Zn-doped and Ti-doped MgO display poorer antibacterial activity than pure MgO. It can be concluded that the influence of different ions doping on the antibacterial properties of MgO mainly lies on oxygen vacancies and basicity of nanopowders.

Sewage sludge conditioning with the application of ash from biomass-fired power plant

Science.gov (United States)

Wójcik, Marta; Stachowicz, Feliks; Masłoń, Adam

2018-02-01

During biomass combustion, there are formed combustion products. Available data indicates that only 29.1 % of biomass ashes were recycled in Poland in 2013. Chemical composition and sorptive properties of ashes enable their application in the sewage sludge treatment. This paper analyses the impact of ashes from biomass-combustion power plant on sewage sludge dewatering and higienisation. The results obtained in laboratory tests proved the possitive impact of biomass ashes on sewage sludge hydration reduction after dewatering and the increase of filtrate volume. After sludge conditioning with the use of biomass combustion by-products, the final moisture content decreased by approximatelly 10÷25 % in comparison with raw sewage sludge depending on the method of dewatering. The application of biomass combustion products in sewage sludge management could provide an alternative method of their utilization according to law and environmental requirements.

Identifying the Physical Properties of Showers That Influence User Satisfaction to Aid in Developing Water-Saving Showers

Directory of Open Access Journals (Sweden)

Minami Okamoto

2015-07-01

Full Text Available This research was conducted with the goal of clarifying the required conditions of water-saving showerheads. In order to this, the research analyzes the mutual relationship between water usage flow, the level of satisfaction and the physical properties of spray of showerheads. The physical properties of spray were measured using physical properties test apparatus of standard or scheme for water-saving showerheads issued in several water-saving countries, and satisfaction evaluation data was acquired through bathing experiments. The evaluated showerheads were separated into three groups according to usage water flow and the level of satisfaction. The relationships between usage water flow, the level of satisfaction and physical properties were compared. The results identified that Spray Force and Spray Force-per-Hole were physical properties that influence usage water flow. Spray force-per-hole, water volume ratio in Spray Patterns within φ 100 and φ 150, Temperature Drop and Spray Angle were identified as physical properties that influenced the level of satisfaction. The level of satisfaction and usage water flow has a spurious correlation through the physical properties of Spray Force-per-Hole and Temperature Drop. It is possible to improve the level of satisfaction independent of amount of water usage through designs that set an appropriate value for water volume ratio and Spray Angle for Spray Patterns within φ 100 and φ 150.

The influence of chemical composition on the properties and structure Al-Si-Cu(Mg alloys

Directory of Open Access Journals (Sweden)

M. Kaczorowski

2007-04-01

Full Text Available The mechanical properties of different chemical composition AlSiCuMg type cast alloys after precipitation hardening are presented. The aim of the study was to find out how much the changes in chemistry of aluminum cast alloys permissible by EN-PN standards may influence the mechanical properties of these alloys. Eight AlSi5Cu3(Mg type cast alloys of different content alloying elements were selected for the study. The specimens cut form test castings were subjected to precipitation hardening heat treatment. The age hardened specimens were evaluated using tensile test, hardness measurements and impact test. Moreover, the structure investigation were carried out using either conventional light Metallography and scanning (SEM and transmission (TEM electron microscopy. The two last methods were used for fractography observations and precipitation process observations respectively. It was concluded that the changes in chemical composition which can reach even 2,5wt.% cause essential differences of the structure and mechanical properties of the alloys. As followed from quantitative evaluation and as could be predicted theoretically, copper and silicon mostly influenced the mechanical properties of AlSi5Cu3(Mg type cast alloys. Moreover it was showed that the total concentration of alloying elements accelerated and intensifies the process of decomposition of supersaturated solid solution. The increase of Cu and Mg concentration increased the density of precipitates. It increases of strength properties of the alloys which are accompanied with decreasing in ductility.

Influence of thermal treatments on the basic and catalytic properties of Mg,Al-mixed oxides derived from hydrotalcites

Directory of Open Access Journals (Sweden)

Bastiani R.

2004-01-01

Full Text Available This work studied the influence of calcination conditions on basic properties and catalytic performance of Mg,Al-mixed oxides derived from a hydrotalcite sample (Al/(Al+Mg=0.20. Various heating rates, calcination atmospheres and lengths of calcination at 723K were evaluated. TPD of CO2 and retroaldolization of diacetone alcohol (DAA were used to determine the basic properties of the mixed oxides. The basic site density determined by TPD of CO2 showed a better correlation with catalytic activity for acetone/citral aldol condensation than the relative basicity obtained from retroaldolization of DAA. Calcination atmosphere was the parameter that influenced most the basic and the catalytic properties of the Mg,Al-mixed oxides, with calcination under dry air being the best choice.

Influence of flooding and landform properties on riparian plant communities in an old-growth northern hardwood watershed

Science.gov (United States)

P. Charles Goebel; Kurt S. Pregitzer; Brian J. Palik

2012-01-01

In most forested landscapes, the organization of plant communities across stream valleys is thought to be regulated by a complex set of interactions including flooding, landform properties, and vegetation. However, few studies have directly examined the relative influence of frequent and infrequent flooding, as well as landform properties, on riparian plant community...

Investigating the Influences of Tree Coverage and Road Density on Property Crime

Directory of Open Access Journals (Sweden)

Chengming Ye

2018-03-01

Full Text Available With the development of Geographic Information Systems (GIS, crime mapping has become an effective approach for investigating the spatial pattern of crime in a defined area. Understanding the relationship between crime and its surrounding environment reveals possible strategies for reducing crime in a neighborhood. The relationship between vegetation density and crime has long been under debate. The convenience of a road network is another important factor that can influence a criminal’s selection of locations. This research is conducted to investigate the correlations between tree coverage and property crime, and road density and property crime in the City of Vancouver. High spatial resolution airborne LiDAR data and road network data collected in 2013 were used to extract tree covered areas for cross-sectional analysis. The independent variables were inserted into Ordinary Least-Squares (OLS regression, Spatial Lag regression, and Geographically Weighted Regression (GWR models to examine their relationships to property crime rates. The results of the cross-sectional analysis provide statistical evidence that there are negative correlations between property crime rates and both tree coverage and road density, with the stronger correlations occurring around Downtown Vancouver.

Mechanical Properties of Weakly Segregated Block Copolymers. 3. Influence of Strain Rate and Temperature on Tensile Properties of Poly(styrene-b-butyl methacrylate) Diblock Copolymers with Different Morphologies

NARCIS (Netherlands)

Weidisch, R.; Stamm, M.; Michler, G.H.; Fischer, H.R.; Jérôme, R.

1999-01-01

Poly(styrene-b-butyl methacrylate) diblock copolymers, PS-6-PBMA, with different morphologies are investigated with respect to the influence of strain rate and temperature on tensile properties. In the first part the mechanical properties of bicontinuous and perforated lamellar structure are

Does the casting mode influence microstructure, fracture and properties of different metal ceramic alloys?

Science.gov (United States)

Bauer, José Roberto de Oliveira; Grande, Rosa Helena Miranda; Rodrigues-Filho, Leonardo Eloy; Pinto, Marcelo Mendes; Loguercio, Alessandro Dourado

2012-01-01

The aim of the present study was to evaluate the tensile strength, elongation, microhardness, microstructure and fracture pattern of various metal ceramic alloys cast under different casting conditions. Two Ni-Cr alloys, Co-Cr and Pd-Ag were used. The casting conditions were as follows: electromagnetic induction under argon atmosphere, vacuum, using blowtorch without atmosphere control. For each condition, 16 specimens, each measuring 25 mm long and 2.5 mm in diameter, were obtained. Ultimate tensile strength (UTS) and elongation (EL) tests were performed using a Kratos machine. Vickers Microhardness (VM), fracture mode and microstructure were analyzed by SEM. UTS, EL and VM data were statistically analyzed using ANOVA. For UTS, alloy composition had a direct influence on casting condition of alloys (Wiron 99 and Remanium CD), with higher values shown when cast with Flame/Air (p casting condition" influenced the EL and VM results, generally presenting opposite results, i.e., alloy with high elongation value had lower hardness (Wiron 99), and casting condition with the lowest EL values had the highest VM values (blowtorch). Both factors had significant influence on the properties evaluated, and prosthetic laboratories should select the appropriate casting method for each alloy composition to obtain the desired property.

Influence of hydrostatic pressure on nuclear radiation detector's properties based on semiconductor alloy CdZnTe

International Nuclear Information System (INIS)

Kutnij, V.E.; Kutnij, D.V.; Rybka, A.V.; Nakonechnyj, D.V.; Babun, A.V.

2003-01-01

The influence of hydrostatic pressure on properties of CdZnTe semiconductor detectors (Cd-50,Zn-2,Te-48 mas.%, 5 centre dot 5 centre dot 2 mm) was investigated. Were considered different types of hydrostatic treatment at 100 MPa, second hydrostatic treatment at 100 MPa and 200 MPa. Hydrostatic pressure influence on detectors electric resistance, J-V characteristics and spectrometric parameters was determined

Influence of ceramic thickness and type on micromechanical properties of light-cured adhesive bonding agents.

Science.gov (United States)

Öztürk, Elif; Bolay, Sükran; Hickel, Reinhard; Ilie, Nicoleta

2014-10-01

The aim of this study was to evaluate the micromechanical properties of different adhesive bonding agents when polymerized through ceramics. Sixty sound extracted human third molars were selected and the crowns were sectioned perpendicular to the long axis in order to obtain dentin slices to be bonded with one of the following adhesives: Syntac/Heliobond (Ivoclar-Vivadent) or Adper-Scotchbond-1XT (3M-ESPE). The adhesives were cured by using a LED-unit (Bluephase®, Ivoclar Vivadent) with three different curing times (10 s, 20 s and 30 s) under two ceramics (IPS-e.max-Press, Ivoclar-Vivadent; IPS-Empress®CAD, Ivoclar-Vivadent) of different thicknesses (0 mm, 0.75 mm, 2 mm). Thirty groups were included, each containing 60 measurements. Micromechanical properties (Hardness, HV; indentation modulus, E; and creep, Cr) of the adhesives were measured with an automatic microhardness indenter (Fisherscope H100C, Germany). Data were statistically analyzed by using one-way ANOVA and Tukey's post-hoc test, as well as a multivariate analysis to test the influence of the study parameters (SPSS 18.0). Significant differences were observed between the micromechanical properties of the adhesives (p ceramic type showed the highest effect on HV (Partial-eta squared (η(2)) = 0.109) of the tested adhesives, while E (η(2) = 0.275) and Cr (η(2) = 0.194) were stronger influenced by the adhesive type. Ceramic thickness showed no effect on the E and Cr of the adhesives. The adhesive bonding agents used in this study performed well by curing through different thicknesses of ceramics. The micromechanical properties of the adhesives were determined by the adhesive type and were less influenced by ceramic type and curing time.

The influence of sediment properties and experimental variables on the efficiency of electrodialytic removal of metals from sediment

DEFF Research Database (Denmark)

Pedersen, Kristine B.; Lejon, Tore; Jensen, Pernille Erland

2017-01-01

Chemometrics was used to determine the influence of sediment properties and experimental settings for the electrodialytic removal (EDR) of Cu, Pb and Zn from six harbour sediments from Greenland and Norway. A Projection onto latent structures (PLS) model revealed that the most important sediment...... properties for achieving acidification (lag-phase, pH > 4), necessary for desorbing and mobilising metals in the polluted sediments, were buffer capacity and grain size distribution. Higher stirring rate reduced the acidification time, stressing the importance of thorough mixing of the sediment suspension...... to achieve a fast and uniform acidification. PLS models were calculated to determine the influence of sediment properties on the removal of metals during EDR, which was observed to vary depending on the targeted metal and the stage of the remediation. In general, buffer capacity, grain size distribution...

Thermophysical properties of hydrophobised lime plasters - The influence of ageing

Science.gov (United States)

Pavlíková, Milena; Zemanová, Lucie; Pavlík, Zbyšek

2017-07-01

The building envelope is a principal responsible for buildings energy loses. Lime plasters as the most popular finishing materials of historical buildings and culture monuments influence the thermal behaviour as well as construction material of masonry. On this account, the effect of ageing on the thermophysical properties of a newly designed lime plasters containing hydrophobic admixture is analysed in the paper. For the comparative purposes, the reference lime plaster is tested. The ageing is accelerated with controlled carbonation process to simulate the final plasters properties. Basic characterization of the tested materials is done using bulk density, matrix density, and porosity measurements. Thermal conductivity and volumetric heat capacity are experimentally assessed using a transient impulse method. The obtained data revealed the significant changes of the both studied thermal parameters in the dependence on plasters composition and age. The assessed material parameters will be stored in a material database, where will find use as an input data for computational modelling of heat transport in this type of porous building materials and evaluation of energy-savings and sustainability issues.

The influence of parent concrete and milling intensity on the properties of recycled aggregates

NARCIS (Netherlands)

Lotfi, Somayeh; Rem, P.C.; Deja, J; Mroz, R; Di Maio, F.; Lotfi, S.; Bakker, M.; Hu, M.; Vahidi, A.

2017-01-01

The C2CA concrete recycling process consists of a combination of smart demolition, gentle grinding of the crushed concrete in an autogenous mill, and a novel dry classification technology called ADR to remove the fines. The` main factors in the C2CA process which influence the properties of Recycled

Influence of bismuth on properties and microstructures of Sr0⋅ 5Ba0 ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 29; Issue 5. Influence of bismuth on properties and microstructures of Sr0.5Ba0.5–Bi TiO3 thin films. Tao Wenhong Wang Yin Fu Xinghua Wei Qihong. Thin Films Volume 29 Issue 5 October 2006 pp 523-527 ...

Influence of layer eccentricity on the resonant properties of cylindrical active coated nano-particles

DEFF Research Database (Denmark)

Thorsen, R. O.; Arslanagic, Samel

2015-01-01

We report on the influence of the layer eccentricity on the resonant properties of active coated nano-particles made of a silver core and gain impregnated silica shell illuminated by a near-by magnetic line source. For a fixed over-all size of the particle, designs with small and large cores...

THE INFLUENCE OF THE NUMBER OF RIPPLE OF POLYACRYLONITRILIC FIBERS COTTON TYPE ON YARN PROPERTIES

Directory of Open Access Journals (Sweden)

HRISTIAN Liliana

2016-05-01

Full Text Available In this study we aimed the influence of the number of undulations of polyacrylonitrile fibers, cotton type, on the properties of yarns with Nm50/1 fineness, made on BD 200 the rotor spinning machine. Rotor spinning of the synthetic fibers is largely influenced by some characteristics of the fibers as being: the quality and quantity of the avivage, frequency of undulations and the number of defects fiber. Tensile properties and structural characteristics aspect of the yarns carried on BD 200 rotor spinning machine are determined, at the fiber content, the structural model and the technological parameters of processing, by the result of the transfer of fibers proprieties, into the meaning fiber-yarn. The yarns structural compactness, determined by the degree of twisting and tensional properties are defining for the quality of yarns and warrants the corresponding to their destination. Structural characteristics of the yarns which are characterized by complexity and diversity of their actions were studied by determining the linear irregularity (U% , standard deviation (CV% and the imperfections in the form of thinning (S, thickening (G, neppines (N, relative to 1000 m yarn.

REPLACEMENT OF SOFTWOOD KRAFT PULP WITH ECF-BLEACHED BAMBOO KRAFT PULP IN FINE PAPER

Directory of Open Access Journals (Sweden)

Guanglei Zhao

2010-06-01

Full Text Available Non-wood fibers such as bamboo and wheat straw have been playing important roles in the pulp and paper industry in China. In this study an ECF-bleached bamboo kraft pulp was compared with a bleached softwood kraft pulp (NBSK as the reinforcement pulp in fine paper production. Areas that were examined include the refining of pure fibers, influence of bamboo on dewatering, retention, and sizing. The influence of bamboo kraft pulp as a part of a furnish replacing NBSK was compared as well. Results show that fiber shortening was more prominent with bamboo when refined. This resulted in a higher amount of fines, and addition wet-end chemicals may be required to compensate. Handsheets with bamboo as a reinforcement fiber showed similar mechanical and optical properties to handsheets containing NBSK.

The influence of chemical composition on the properties and structure Al-Si-Cu(Mg) alloys

OpenAIRE

M. Kaczorowski; A. Krzyńska

2007-01-01

The mechanical properties of different chemical composition AlSiCuMg type cast alloys after precipitation hardening are presented. The aim of the study was to find out how much the changes in chemistry of aluminum cast alloys permissible by EN-PN standards may influence the mechanical properties of these alloys. Eight AlSi5Cu3(Mg) type cast alloys of different content alloying elements were selected for the study. The specimens cut form test castings were subjected to precipitation hardening ...

Influence of surface oxidation on the radiative properties of ZrB{sub 2}-SiC composites

Energy Technology Data Exchange (ETDEWEB)

Li, Ning, E-mail: lncaep@163.com [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang, 621900 (China); Xing, Pifeng; Li, Cui [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang, 621900 (China); Wang, Peng [School of Material Science and Engineering, Shandong University of Technology, Zibo 255049 (China); Jin, Xinxin [College of Materials Science and Engineering, Harbin University of Science and Technology, Harbin 150040 (China); Zhang, Xinghong [Science and Technology on Advanced Composites in Special Environments Laboratory, Harbin Institute of Technology, Harbin 150001 (China)

2017-07-01

Highlights: • Surface component affected radiative properties of ZrB{sub 2}-SiC composites significantly. • Emissivity in long-wave range gradually increased with the thickness of oxide scale. • The surface temperature had a little effect on radiative properties of composites. • Influence of surface roughness on emissivity could be negligible. • Covering the surface with glass is a method for improving radiative properties. - Abstract: The spectral emissivities of ZrB{sub 2}-20 vol.% SiC composites with various surface components of ZrB{sub 2}/SiC (ZS1), silica-rich glass (ZS2) and porous zirconia (ZS3) were measured using infrared spectrometer in the wavelength range from 2.5 to 25.0 μm. The relationship between surface oxidation (associated with surface component, thickness of oxide scale, testing temperature as well as roughness) and the radiative properties of ZrB{sub 2}-SiC composites were investigated systematically. Surface component affected the radiative properties of composites significantly. The total emissivity of ZS1 varied from 0.22 to 0.81 accompanied with surface oxidation in the temperature range 300–900 °C. The emissivity of ZS2 was about 1.5 times as that of ZS3 under the same testing conditions. The oxide scale on specimen surface enhanced the radiative properties especially in terms of short-wave range, and the emissivity in the long-wave range gradually increased with the thickness of oxide scale within a certain range. The influence of testing temperature and surface roughness was also investigated. The testing temperature had a little effect on radiative properties, whereas effect of surface roughness could be negligible.

Short term preservation of hide using vacuum: influence on properties of hide and of processed leather.

Science.gov (United States)

Gudro, Ilze; Valeika, Virgilijus; Sirvaitytė, Justa

2014-01-01

The objective of this work was to investigate vacuum influence on hide preservation time and how it affects hide structure. It was established that vacuum prolongs the storage time without hide tissue putrefaction up to 21 days when the storage temperature is 4°C. The microorganisms act for all storage times, but the action is weak and has no observable influence on the quality of hide during the time period mentioned. The hide shrinkage temperature decrease is negligible, which shows that breaking of intermolecular bonds does not occur. Optical microscopy, infrared spectroscopy and differential scanning calorimetry also did not show any structural changes which can influence the quality of leather produced from such hide. The qualitative indexes of wet blue processed under laboratory conditions and of leather produced during industrial trials are presented. Indexes such as chromium compounds exhaustion, content of chromium in leather, content of soluble matter in dichloromethane, strength properties, and shrinkage temperature were determined. Properties of the leather produced from vacuumed hide under industrial conditions conformed to the requirements of shoe upper leather.

The disc method. A new method for selecting facilitations in flocculating sludge to be dewatered in centrifuges; Metodo de disco. Un nuevo metodo para la seleccion de floculantes en la floculacion de lodos a deshidratar en centrifugas

Energy Technology Data Exchange (ETDEWEB)

Canga Rodriguez, J.; Gutierrez Lavin, A.

2002-07-01

An experimental protocol was designed at a laboratory scale, in view of achieving the selection with different poly electrolytes related to the chemical conditioning (flocculation) of sewage sludge before dewatering it in a drying centrifuge. The method is based on a new parameter of quality of the formed floc, which measures its compaction when is submitted to a fix external strength. Some experimental tests have been introduced, whose results are numbers, avoiding all subjective aspects related to direct observation of flocs. (Author) 8 refs.

Influence of industrial solid waste addition on properties of soil-cement bricks

OpenAIRE

Siqueira, F. B.; Amaral, M. C.; Bou-Issa, R. A.; Holanda, J. N. F.

2016-01-01

Abstract The reuse of pollutant solid wastes produced in distinct industrial activities (avian eggshell waste and welding flux slag waste) as a source of alternative raw material for producing soil-cement bricks for civil construction was investigated. Soil-cement bricks containing up to 30 wt% of industrial solid waste were uniaxially pressed and cured for 28 days. Special emphasis is given on the influence of solid waste addition on the technical properties (as such volumetric shrinkage, wa...

Rheological properties of disintegrated sewage sludge

Science.gov (United States)

Wolski, Paweł

2017-11-01

The rheology of the sludge provides information about the capacity and the flow, which in the case of project tasks for the hydraulic conveying installation is an important control parameter. Accurate knowledge of the rheological properties of sludge requires the designation of rheological models. Models single and multiparameter (Ostwald, Bingham, Herschel-Bulkley'a, and others) allow an approximation of flow curves, and the determination of the boundaries of the flow of modified sludge allows you to control the process compaction or are dewatered sludge undergoing flow. The aim of the study was to determine the rheological parameters and rheological models of sludge conditioned by physical methods before and after the process of anaerobic digestion. So far, studies have shown that the application of conditioning in the preparation of sewage sludge increases shear stress, viscosity as well as the limits of flow in relation to the untreated sludge. Offset yield point by the application of a conditioning agent is associated with decreased flowability tested sludge, which has also been observed by analyzing the structure of the prepared samples. Lowering the yield point, and thus the shear stress was recorded as a result of the fermentation test of disintegrated sludge.

Influence of low shear mixing settings on the mechanical properties of long glass fibre polypropylene

NARCIS (Netherlands)

de Bruijn, Thomas A.; Vincent, Guillaume Almire; van Hattum, Ferrie

2017-01-01

The influence of several mixing settings on the mechanical properties were studied. A Long fibre thermoplastic glass polypropylene material was mixed, compression moulded and analysed by flexural tests and charpy impact. In a low-shear mixing machine, chosen for limited fibre length degradation, six

How Far Does a Receptor Influence Vibrational Properties of an Odorant?

Science.gov (United States)

Reese, Anna; List, Nanna Holmgaard; Kongsted, Jacob; Solov'yov, Ilia A

2016-01-01

The biophysical mechanism of the sense of smell, or olfaction, is still highly debated. The mainstream explanation argues for a shape-based recognition of odorant molecules by olfactory receptors, while recent investigations suggest the primary olfactory event to be triggered by a vibrationally-assisted electron transfer reaction. We consider this controversy by studying the influence of a receptor on the vibrational properties of an odorant in atomistic details as the coupling between electronic degrees of freedom of the receptor and the vibrations of the odorant is the key parameter of the vibrationally-assisted electron transfer. Through molecular dynamics simulations we elucidate the binding specificity of a receptor towards acetophenone odorant. The vibrational properties of acetophenone inside the receptor are then studied by the polarizable embedding density functional theory approach, allowing to quantify protein-odorant interactions. Finally, we judge whether the effects of the protein provide any indications towards the existing theories of olfaction.

Influence of heat treatment on microstructure and properties of bainitic cast steel used for frogs in railway crossovers

Directory of Open Access Journals (Sweden)

E. Tasak

2010-01-01

Full Text Available This work deals with influence of heat treatment on microstructure and properties of sample cast assigned as a material used for frogs in railway crossover. Materials used in railway industry for frogs (manganese cast steel and forged pearlitic steel do not fulfil strict conditions of exploitation of railway. One of the solutions is using cast steel with bainitic or bainite-martensite microstructure, what allows to gain high resistance properties (Rm = 1400 MPa, Rp0,2 = 900 MPa, hardness to 400 HBW. The cooling rates of rail type UIC60 shows that it is possible to reach the bainitic microstructure in cast of frog. The microstructure of lower banite should have an advantageous influence on cracking resistance. In order to set the parameters of heat treatment, the critical temperatures were determined by dilatometric methods determined. This heat treatment consisted of normalizing that prepared it to the farther process of resistance welding. Moreover, the CCT diagram of proposed bainitic cast steel was prepared. The exams were done that can be used to evaluate the influence of heat treatment on microstructure and properties of the sample cast.

Flotation tailings as a raw material for ceramic building materials

Energy Technology Data Exchange (ETDEWEB)

Burmistrov, V N; Karpunina, T I; Smolin, V N

1986-02-01

The VNIIstrom research institute developed a method for utilizing flotation tailings for production of bricks. Tailings are dewatered using filter presses. After dewatering, moisture content in the tailings ranges from 25 to 26%. Tailings are mixed with chamotte with a grain size to 2 mm. Using 30% chamotte improves mechanical and physical properties of the bricks and reduces energy consumption of brick firing. Tailings mixed with chamotte are granulated and dried on a conveyor. Granules with moisture content reduced to the optimum level are mixed a second time and formed in a press. The bricks are fired in a tunnel kiln with modified design. The bricks made of flotation tailings mixed with 30% chamotte are characterized by mechanical properties comparable to those of high quality bricks made of conventional materials.

Analysis of Different Breed of Protein Fibres and their Influence on Mechanical Properties of Woollen Blend Yarns

Directory of Open Access Journals (Sweden)

Audronė RAGAIŠIENĖ

2016-09-01

Full Text Available The aim of this research was to analyse possibilities of making different woollen blend yarns with sheep’s wool and dog’s hair fibers and to investigate geometrical and mechanical properties of these yarns. In this paper sheep’s wool and dogs’ hair fibers were compared one with other in different geometrical (fibre surface, length, diameter, linear density and mechanical (breaking tenacity, elongation at break, breaking toughness properties. It was estimated that the sheep’s and the dog’s fibers are visually very different, they have various types of scales, also most of the dog’s hair have channels inside them. On the next stage of this work the woollen blend yarns were made by mixing the wool of German Blackface sheep with different breed (English Spaniel, Poodle, Yorkshire Terrier dogs’ hair 15 %, 25 % and 35 %. After evaluating the linear density and mechanical properties of woollen blend yarns, it was estimated that influence of fiber composition in the yarns on these properties is different. Different values of the investigated properties are mostly influenced by spinning system of these yarns. The condenser spinning system affects inequality and unpredictable properties of woollen blend yarns. Also, obtained results depend on the breed of protein fibers, hairy surface, hollow structure and bending rigidity of fiber, the technological process or even compatibility of used devices.DOI: http://dx.doi.org/10.5755/j01.ms.22.3.8974

The influence of assist gas on magnetic properties of electrotechnical steel sheets cut with laser

International Nuclear Information System (INIS)

Gaworska-Koniarek, Dominika; Szubzda, Bronislaw; Wilczynski, Wieslaw; Drosik, Jerzy; Karas, Kazimierz

2011-01-01

The paper presents the influence of assist gas (air and nitrogen) during laser cutting on magnetization, magnetic permeability and loss characteristics of non-oriented electrical steels. The research was made on an non-oriented M330-50A grade electrical steels by means of single sheet tester. In order to enhance the effect of cutting and the same degradation zone on magnetic properties, strips with different width were achieved. Measurements results indicate that application of air as assist gas has more destructive effect on magnetic properties of electrical steels than nitrogen one.

The influence of assist gas on magnetic properties of electrotechnical steel sheets cut with laser

Science.gov (United States)

Gaworska-Koniarek, Dominika; Szubzda, Bronisław; Wilczyński, Wiesław; Drosik, Jerzy; Karaś, Kazimierz

2011-07-01

The paper presents the influence of assist gas (air and nitrogen) during laser cutting on magnetization, magnetic permeability and loss characteristics of non-oriented electrical steels. The research was made on an non-oriented M330-50A grade electrical steels by means of single sheet tester. In order to enhance the effect of cutting and the same degradation zone on magnetic properties, strips with different width were achieved. Measurements results indicate that application of air as assist gas has more destructive effect on magnetic properties of electrical steels than nitrogen one.

Microstructural changes of AISI 316L due to structural sensitization and its influence on the fatigue properties

Directory of Open Access Journals (Sweden)

Sylvia Dundeková

2014-11-01

Full Text Available Mechanical and fatigue properties of material are dependent on its microstructure. The microstructure of AISI 316L stainless steel commonly used for the production of medical tools, equipment and implants can be easily influenced by its heat treatment. Microstructural changes and fatigue properties of AISI 316L stainless steel due to the heat treatment consisted of annealing at the temperature of 815°C with the dwell time of 500 hours were analyzed in the present paper. Precipitation of intermetallic phases and carbides was observed as a response of the material to the applied heat treatment. Small negative influence was observed in the case of fatigue region bellow 105 cycles; however the fatigue limit remains unchanged due to the structural sensitization.

Experimental investigation concerning the influence of fuel type and properties on the injection and atomization of liquid biofuels in an optical combustion chamber

International Nuclear Information System (INIS)

Galle, J.; Defruyt, S.; Van de Maele, C.; Rodriguez, R. Piloto; Denon, Q.; Verliefde, A.; Verhelst, S.

2013-01-01

Due to the scarcity of fossil fuels and the future stringent emission limits, there is an increasing interest for the use of renewable biofuels in compression ignition engines. However, these fuels have different physical, chemical and thermodynamic properties affecting atomization, spray development and combustion processes. The results reported in this paper have been obtained by experimentation with a constant volume combustion chamber. The influences of physical fuel properties on injections under non-evaporating conditions are studied, using a pump-line-nozzle system from a medium speed diesel engine with injection pressures up to 1200 bar, by changing the fuel type and temperature. Experiments were conducted for diesel, biodiesel, straight vegetable oils and animal fats. Injection pressure and needle lift measurements were analyzed. A high speed camera was used to visualize the spray, which enabled us to study the spray penetration and spray angle. Our results show that the fuel temperature is an important parameter to control because it significantly affects the fuel properties. Both the injection timing and injection duration are affected by the fuel properties. The influences of these properties on the spray development were less pronounced. At low temperatures, a strongly deteriorated atomization of oils and fats was observed. -- Highlights: • Spray measurements in an optical combustion chamber. • Influence on the injections system is compared for different bio-fuels. •Temperature effects the fuel properties, with strong influence on the injection system. • Viscosity has significant influence on atomization, especially for viscous fuels. • No difference for spray penetration and angle unlike the mass distribution

Influence of the microstructural changes and induced residual stresses on tensile properties of wrought magnesium alloy friction stir welds

International Nuclear Information System (INIS)

Commin, Loreleï; Dumont, Myriam; Rotinat, René; Pierron, Fabrice; Masse, Jean-Eric; Barrallier, Laurent

2012-01-01

Highlights: ► Study of AZ31 FSW mechanical behaviour. ► Early yielding occurs in the TMAZ, the nugget and base metal zones undergo almost no plastic strains. ► Texture gradient in the TMAZ localises the deformations in this area. ► Residual stresses have a major influence in FSW mechanical behaviour. - Abstract: Friction stir welding induces a microstructural evolution and residual stresses that will influence the resulting mechanical properties. Friction stir welds produced from magnesium alloy hot rolled plates were studied. Electron back scattered diffraction was used to determine the texture evolution, residual stresses were analysed using X ray diffraction and tensile tests coupled with speckle interferometry were performed. The residual stresses induced during friction stir welding present a major influence on the final mechanical properties.

Influence of titanium volume fraction on the mechanical properties of Mg-Ti composites

Energy Technology Data Exchange (ETDEWEB)

Perez, Pablo; Garces, Gerardo; Adeva, Paloma [Centro Nacional de Investigaciones Metalurgicas (CENIM, CSIC), Madrid (Spain). Dept. de Metalurgia Fisica

2009-03-15

The influence of titanium volume fraction on the mechanical properties of Mg-Ti composites prepared through a powder metallurgy route has been evaluated. Titanium was added as particles smaller than 25 {mu}m and volume fractions ranging from 5 to 15%. The increase in the volume fraction of titanium particles results in a slight decrease in the maximum strength. In contrast to this, the ductility of all composites was significantly enhanced by titanium additions. The mechanical properties can be explained on the basis of texture changes induced by the presence of titanium particles. The decrease in the basal texture along the extrusion direction as the amount of titanium is progressively increased accounts for the decrease in the maximum strength. (orig.)

Influence of the gypsum dehydration temperature and alkali additives on the properties of anhydrite cement

Directory of Open Access Journals (Sweden)

Leskeviciene V.

2010-01-01

Full Text Available While dehydrating gypsum with additives at the temperatures of 800°C and 900°C the influence of alkali additives on both the crystalline structure of anhydrite and properties of anhydrite binder was investigated. The industrial and household wastes including other lowcost materials were used as additives. Having heated them with gypsum the anhydrite with alkali activation properties was obtained. The properties of such substances were evaluated using the methods of chemical, diffractive X-ray scanning and scanning electron microscopy (SEM analyses. Some additives, e.g. 5 % ground glass waste, were found to increase crystal agglomerate formation of anhydrite binder, accelerate the hydration process of anhydrite and double the compressive strength of hydrated samples compared to samples without additives.

Influence of the mechanical properties of sputtered Mo solar cell back contacts on laser scribing

Energy Technology Data Exchange (ETDEWEB)

Schultz, Christof; Schuele, Manuel; Quaschning, Volker; Stegemann, Bert; Fink, Frank [University of Applied Sciences (HTW) Berlin, Wilhelminenhofstr. 75A, 12459 Berlin (Germany); Endert, Heinrich [Newport Spectra-Physics GmbH, Ruhlsdorfer Strasse 95, 14532 Stahnsdorf (Germany); Bonse, Joern [BAM Bundesanstalt fuer Materialforschung und -pruefung, Berlin (Germany); Rau, Bjoern; Schlatmann, Rutger [PVcomB - Competence Centre Thin-Film and Nanotechnology for Photovoltaics Berlin, Schwarzschildstr. 3, 12489 Berlin (Germany)

2012-07-01

In thin-film photovoltaics complete laser structuring of the solar modules is aimed to perform appropriate monolithic serial interconnection. We have studied the laser ablation behavior of sputtered molybdenum back contacts for chalcopyrite solar cells. The properties of these Mo layer are sensitive to the sputter conditions. The process pressure influences the mechanical layer properties and, thus, contributes directly to the quality of the laser scribes. Precise, reliable and reproducible laser scribing requires the proper adaptation of the laser parameters to the material properties. In our study it was achieved by comprehensive analysis of the laser matter interaction and by detailed determination of the ablation thresholds as a function of the Mo layer thickness and ductility for different laser wavelengths and pulse durations, accompanied by thermal modeling.

Characterization of ductile fracture properties of quench-hardenable boron steel: Influence of microstructure and processing conditions

International Nuclear Information System (INIS)

Golling, Stefan; Östlund, Rickard; Oldenburg, Mats

2016-01-01

Developments of the hot stamping technology have enabled the production of components with differential microstructure composition and mechanical properties. These can increase the performance of certain crash-relevant automotive structures by combining high intrusion protection and energy absorption. This paper presents a comprehensive experimental investigation on the flow and ductile fracture properties of boron-alloyed steel with a wide range of different microstructure compositions. Three types of dual phase microstructures at three different volume fractions, and one triple phase grade, were generated by thermal treatment. Flow curves extending beyond necking and the equivalent plastic strain to fracture for each grade was determined by tensile testing using full-field measurements. The influence of phase composition and microstructural parameters were further investigated by means of a multi-scale modeling approach based on mean-field homogenization in combination with local fracture criteria. Inter-phase and intra-phase fracture mechanisms were considered by adopting two separate fracture criteria formulated in terms of the local average stress field. The micromechanical model captures with useful accuracy the strong influence of microstructure and processing conditions on the flow and fracture properties, implying promising prospects of mean-field homogenization for the constitutive modeling of hot stamped components.

Characterization of ductile fracture properties of quench-hardenable boron steel: Influence of microstructure and processing conditions

Energy Technology Data Exchange (ETDEWEB)

Golling, Stefan, E-mail: stefan.golling@ltu.se [Luleå University of Technology, SE 971 87 Luleå (Sweden); Östlund, Rickard [Gestamp HardTech, Ektjärnsvägen 5, SE 973 45 Luleå (Sweden); Oldenburg, Mats [Luleå University of Technology, SE 971 87 Luleå (Sweden)

2016-03-21

Developments of the hot stamping technology have enabled the production of components with differential microstructure composition and mechanical properties. These can increase the performance of certain crash-relevant automotive structures by combining high intrusion protection and energy absorption. This paper presents a comprehensive experimental investigation on the flow and ductile fracture properties of boron-alloyed steel with a wide range of different microstructure compositions. Three types of dual phase microstructures at three different volume fractions, and one triple phase grade, were generated by thermal treatment. Flow curves extending beyond necking and the equivalent plastic strain to fracture for each grade was determined by tensile testing using full-field measurements. The influence of phase composition and microstructural parameters were further investigated by means of a multi-scale modeling approach based on mean-field homogenization in combination with local fracture criteria. Inter-phase and intra-phase fracture mechanisms were considered by adopting two separate fracture criteria formulated in terms of the local average stress field. The micromechanical model captures with useful accuracy the strong influence of microstructure and processing conditions on the flow and fracture properties, implying promising prospects of mean-field homogenization for the constitutive modeling of hot stamped components.

Influence of Microstructure on the Electrical Properties of Heteroepitaxial TiN Films

Science.gov (United States)

Xiang, Wenfeng; Liu, Yuan; Zhang, Jiaqi

2018-03-01

Heteroepitaxial TiN films were deposited on Si substrates by pulse laser deposition at different substrate temperature. The microstructure and surface morphology of the films were investigated by X-ray diffraction (θ-2θ scan, ω-scan, and ϕ-scan) and atomic force microscopy. The electrical properties of the prepared TiN films were studied using a physical property measurement system. The experimental results showed that the crystallinity and surface morphology of the TiN films were improved gradually with increasing substrate temperature below 700 °C. Specially, single crystal TiN films were prepared when substrate temperature is above 700 °C; However, the quality of TiN films gradually worsened when the substrate temperature was increased further. The electrical properties of the films were directly correlated to their crystalline quality. At the optimal substrate temperature of 700 °C, the TiN films exhibited the lowest resistivity and highest mobility of 25.7 μΩ cm and 36.1 cm2/V s, respectively. In addition, the mechanism concerning the influence of substrate temperature on the microstructure of TiN films is discussed in detail.

EVALUATION OF BIOAEROSOL COMPONENTS, GENERATION FACTORS, AND AIRBORNE TRANSPORT ASSOCIATED WITH LIME TREATMENT OF CONTAMINATED SEDIMENT

Science.gov (United States)

Lime treatment has been used in contaminated sediment management activities for many purposes such as dewatering, improvement of physical properties, and reducing contaminant mobility. Exothermic volatilization of volatile organic compounds from lime-treated sediment is well kno...

The influence of tungsten powder grain size on the properties of small bars and thick wires

International Nuclear Information System (INIS)

Jesionek, B.; Ludynski, Z.

1980-01-01

The object of the investigations was, if possible, to determine the exact significance of the influence of the pressing parameters on the properties of tungsten bars and larger diameter wires, with special reference to the size of the tungsten grains. Tungsten powders, reduced under different conditions and with different grain sizes, were used for the investigations. These powders were pressed in steel dies at three different pressures, 72.5, 108, and 176 MPa, and the pressings were sintered. After sintering, the following properties of the bars were examined: ability to sinter, strength, and grain size. The bars were then worked down to 1.02 mm diameter wire and the following properties measured: tensile strength, plastic properties and the occurence of internal flaws (cracks). Finally, the optimum pressing parameters of the tungsten powder were determined. (Auth.)

Influence of thermal debinding on the final properties of Fe–Si soft magnetic alloys for metal injection molding (MIM)

Energy Technology Data Exchange (ETDEWEB)

Páez-Pavón, A.; Jiménez-Morales, A. [Dpto. Ciencia e Ing. de materiales e Ing. Química, Universidad Carlos III de Madrid, 28911 Leganés, Madrid (Spain); Santos, T.G. [UNIDEMI, Departamento de Engenharia Mecânica e Industrial, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Quintino, L. [Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Torralba, J.M. [Dpto. Ciencia e Ing. de materiales e Ing. Química, Universidad Carlos III de Madrid, 28911 Leganés, Madrid (Spain)

2016-10-15

Metal injection molding (MIM) may be used to produce soft magnetic materials with optimal mechanical and magnetic properties. Unlike other techniques, MIM enables the production of complex and small Fe–Si alloy parts with silicon contents greater than 3% by weight. In MIM process development, it is critical to design a proper debinding cycle not only to ensure complete removal of the binder system but also to obtain improved properties in the final part. This work is a preliminary study on the production of Fe-3.8Si soft magnetic parts by MIM using pre-alloyed powders and a non-industrialized binder. Two different heating rates during thermal debinding were used to study their effect on the final properties of the part. The final properties of the sintered parts are related to thermal debinding. It has been demonstrated that the heating rate during thermal debinding has a strong influence on the final properties of Fe–Si soft magnetic alloys. - Highlights: • The properties of MIM Fe-Si alloy are influenced by the debinding heating rate. • The slow debinding led to a lower porosity, lower oxygen content and grain growth. • The magnetization of the sintered samples improved after a slow thermal debinding.

Influence of the Organophilisation Process on Properties of the Bentonite Filler and Mechanical Properties of the Clay/Epoxy Nanocomposites

Directory of Open Access Journals (Sweden)

Rapacz-Kmita A.

2016-06-01

Full Text Available In this comparative study, the influence of the organophilisation process on the properties of resulting organobentonite fillers and their capability to improve the mechanical properties of clay/polymer nanocomposites were investigated. The organobentonites were obtained by activation with the use of two organic quaternary ammonium salts (QAS with alkyl chains of significantly different lengths. The organophilisation resulted in an increase in the interlayer space of clays, which was confirmed by XRD analysis. The obtained organofillers were used to produce nanoclay/epoxy resin composites and the effects of alkyl chain length on the resulting properties of composites were compared based on the examination of mechanical behaviour and morphology, and a composite filled with the non organophilised bentonite was used as a reference material. It was demonstrated that the organophilisation process using distearyldimethyl ammonium chloride salt with a longer alkyl chain (C18-C20 created a more superior conditions for the compatibility of nanofiller with a polymer matrix, resulting in a 25 % increase in the bending strength of the epoxy composite material filled with 3 %wt of the organophilised bentonite, comparing to neat epoxy.

The Influence of Ice Properties on Borehole Deformation at the West Antarctic Ice Sheet Divide

Science.gov (United States)

Sinkler, E.; Pettit, E. C.; Obbard, R. W.

2017-12-01

It is widely known that ice flow is affected by many properties, including crystal fabric and impurities, though these relationships are not fully understood. This study uses data from the West Antarctic Ice Sheet (WAIS) Divide borehole to better determine the influence of such properties on ice flow. The WAIS Divide borehole, the byproduct of the 2006-2012 coring project, offers a unique opportunity to study deep Antarctic Ice. Thanks to the work of many researchers, extensive data on ice properties are available from both coring and borehole logging at this site. The borehole, kept open with a density-approximating fluid, closes and tilts due to ice flow. We have tracked this deformation over two years using a set of repeat measurements with an Acoustic Televiewer. This tool acts as an acoustic caliper allowing us to view cross-sections of the borehole shape and size with up to 1.25 degree azimuthal resolution and a depth resolution as high as 1.4 mm. In addition, the tool collects tilt and azimuth data. These measurements are compared to a 1D Glen's Flow Law model for borehole closure that uses density differences between the ice and borehole fluid as its driving force and incorporates temperature effects. This is then compared to ice properties like crystal fabric and impurities in order to determine the influence of these properties on ice deformation at this site. Crystal fabric has appeared as an important factor in this study.This work builds on that of others who have studied in-situ deep ice through borehole deformation (e.g. Paterson, 1977 and Dahl-Jensen and Gundestrup, 1987). Our results have implications for ice flow modeling and therefore interpretation of depth-age relationships in deep ice cores.

Powder properties and compaction parameters that influence punch sticking propensity of pharmaceuticals.

Science.gov (United States)

Paul, Shubhajit; Taylor, Lisa J; Murphy, Brendan; Krzyzaniak, Joseph F; Dawson, Neil; Mullarney, Matthew P; Meenan, Paul; Sun, Changquan Calvin

2017-04-15

Punch sticking is a frequently occurring problem that challenges successful tablet manufacturing. A mechanistic understanding of the punch sticking phenomenon facilitates the design of effective strategies to solve punch sticking problems of a drug. The first step in this effort is to identify process parameters and particle properties that can profoundly affect sticking performance. This work was aimed at elucidating the key material properties and compaction parameters that influence punch sticking by statistically analyzing punch sticking data of 24 chemically diverse compounds obtained using a set of tooling with removable upper punch tip. Partial least square (PLS) analysis of the data revealed that particle surface area and tablet tensile strength are the most significant factors attributed to punch sticking. Die-wall pressure, ejection force, and take-off force also correlate with sticking, but to a lesser extent. Copyright © 2017 Elsevier B.V. All rights reserved.

Does the contact time of alginate with plaster cast influence its properties?

Directory of Open Access Journals (Sweden)

Mariana Marquezan

Full Text Available The aim of this study was to verify the influence of the time of contact between alginate and gypsum after the modeling procedure on the properties of the plaster cast, such as surface detail, dimensional stability and microhardness. Thirty cylindrical specimens of orthodontic gypsum Type III were made by means of impressions of a stainless steel master model which had five reference lines in the upper surface. The samples were divided into two groups: Group 1 (G1 - with time of contact of 1 hour; and Group 2 (G2 - 12 hours of contact. All the specimens were stored up to 48 hours until they underwent laboratory testing. Surface detail and dimensional stability were tested by one calibrated examiner using a visual analysis and a profilometer (Profile Projector Nikon model 6C, Nikon Corporation, Tokyo, Japan, respectively, to evaluate the quality of reproduction of the lines and the distances between them. The microhardness was determined for each sample by making six indentations with a Vickers diamond pyramid indenter (Buehler, Lake Bluff, USA under a load of 100 gF for 15 s. The results showed significant difference (P £ 0.05 between groups in two of the three properties examined: surface detail and microhardness, which decreased as the time of contact rose. The 12-hour time of contact between alginate and the plaster cast is not recommended because it influences the quality of the plaster cast.

Does the contact time of alginate with plaster cast influence its properties?

Directory of Open Access Journals (Sweden)

Mariana Marquezan

2012-06-01

Full Text Available The aim of this study was to verify the influence of the time of contact between alginate and gypsum after the modeling procedure on the properties of the plaster cast, such as surface detail, dimensional stability and microhardness. Thirty cylindrical specimens of orthodontic gypsum Type III were made by means of impressions of a stainless steel master model which had five reference lines in the upper surface. The samples were divided into two groups: Group 1 (G1 - with time of contact of 1 hour; and Group 2 (G2 - 12 hours of contact. All the specimens were stored up to 48 hours until they underwent laboratory testing. Surface detail and dimensional stability were tested by one calibrated examiner using a visual analysis and a profilometer (Profile Projector Nikon model 6C, Nikon Corporation, Tokyo, Japan, respectively, to evaluate the quality of reproduction of the lines and the distances between them. The microhardness was determined for each sample by making six indentations with a Vickers diamond pyramid indenter (Buehler, Lake Bluff, USA under a load of 100 gF for 15 s. The results showed significant difference (P £ 0.05 between groups in two of the three properties examined: surface detail and microhardness, which decreased as the time of contact rose. The 12-hour time of contact between alginate and the plaster cast is not recommended because it influences the quality of the plaster cast.

Influence of Hot-Working Conditions on High-Temperature Properties of a Heat-Resistant Alloy

Science.gov (United States)

Ewing, John F; Freeman, J W

1957-01-01

The relationships between conditions of hot-working and properties at high temperatures and the influence of the hot-working on response to heat treatment were investigated for an alloy containing nominally 20 percent molybdenum, 2 percent tungsten, and 1 percent columbium. Commercially produced bar stock was solution-treated at 2,200 degrees F. to minimize prior-history effects and then rolled at temperatures of 2,200 degrees, 2,100 degrees, 2,000 degrees, 1,800 degrees, and 1,600 degrees F. Working was carried out at constant temperature and with incremental decreases in temperature simulating a falling temperature during hot-working. In addition, a few special repeated cyclic conditions involving a small reduction at high temperature followed by a small reduction at a low temperature were used to study the possibility of inducing very low strengths by the extensive precipitation accompanying such properties. Most of the rolling was done in open passes with a few check tests being made with closed passes. Heat treatments at both 2,050 degrees and 2,200 degrees F. subsequent to working were used to study the influence on response to heat treatment.

The influence of the manufacturing method on the microstructure and drawing properties of copper wires

International Nuclear Information System (INIS)

Gruber, A.; Jeglitsch, F.

1982-01-01

Copper is the third most important common metal from production figures after iron and aluminium and is largely used as pure metal in the electroindustry mainly here in the form of wires of different sizes due to its excellent electrical properties. Therefore all factors influencing the drawing ability are very important. The following work deals with the influence of impurity measurements as well as of the microstructure on the deformation or recrystallization behaviour in manufacturing continuous casting and rolling wire and dip-forming wire, and gives a rupture cause specific to each manufacturing method in the wire drawing process. (orig.) [de

The influence of remelting on the properties of AlSi6Cu4 alloy modified by antimony

Directory of Open Access Journals (Sweden)

D. Medlen

2012-01-01

Full Text Available The paper deals with the problem of multiple remelting influence on AlSi6Cu4 alloy modified by antimony on chosen mechanical characteristics, microstructure and gas content. This foundry alloy is used mostly in automotive industry. Foundry Aluminum-Silicon alloys are also used in number of industrial weight sensitive applications because of their low weight and very good castability and good mechanical properties. Modifiers are usually added to molten aluminum-silicon alloys to refine the eutectic phase particle shape and improve the mechanical properties of the final cast products and Al-Si alloys cast properties.

The Analysis of the Influence of the Polystyrene Patterns Shaping Parameters on the Resistance Properties

Directory of Open Access Journals (Sweden)

T. Pacyniak

2012-04-01

Full Text Available This work presents the technology of making foam plastics patterns used in casting as well as the final shaping stand. The analysis of the sintering process was carried out aiming at determining the influence of the pressure and the time of sintering on the flexural strength properties. The analysis of the research results confirmed that when the sintering pressure grows to the value of Pa =1,7 bar the flexural strength also increases, when the pressure value is higher than that, the degradation of the material takes place and the strength properties decrease.

Influence of hematite nanorods on the mechanical properties of epoxy resin

Directory of Open Access Journals (Sweden)

Bogdanović Gordana

2017-01-01

Full Text Available The mechanical properties of nanocomposites obtained by incorporation of fairly uniform hematite nanorods (α-Fe2O3 NRs into epoxy resin were studied as a function of the content of the inorganic phase. A thorough microstructural characterization of the α-Fe2O3 NRs and the nanocomposites was performed using transmission electron microscopy (TEM and atomic force microscopy (AFM. The TEM measurements revealed rod-like morphology of the nanofiller with a uniform size distribution (8.5 nm×170 nm, diameter×length. High-magnification TEM and AFM measurements indicated agglomeration of α-Fe2O3 NRs embedded in the epoxy resin. Stress at break, strain at break, elastic modulus and tensile toughness of the nanocomposites were compared with the data obtained for pure epoxy resin. Significant influence of nanofiller on the mechanical properties of epoxy resin, as well as on the glass transition temperature, could be noticed for samples with low contents of the inorganic phase (up to 1 wt. %. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 45020

Influence of Cobalt on the Properties of Load-Sensitive Magnesium Alloys

Directory of Open Access Journals (Sweden)

Kai Kerber

2012-12-01

Full Text Available In this study, magnesium is alloyed with varying amounts of the ferromagnetic alloying element cobalt in order to obtain lightweight load-sensitive materials with sensory properties which allow an online-monitoring of mechanical forces applied to components made from Mg-Co alloys. An optimized casting process with the use of extruded Mg-Co powder rods is utilized which enables the production of magnetic magnesium alloys with a reproducible Co concentration. The efficiency of the casting process is confirmed by SEM analyses. Microstructures and Co-rich precipitations of various Mg-Co alloys are investigated by means of EDS and XRD analyses. The Mg-Co alloys’ mechanical strengths are determined by tensile tests. Magnetic properties of the Mg-Co sensor alloys depending on the cobalt content and the acting mechanical load are measured utilizing the harmonic analysis of eddy-current signals. Within the scope of this work, the influence of the element cobalt on magnesium is investigated in detail and an optimal cobalt concentration is defined based on the performed examinations.

Computer modelling system of the chemical composition and treatment parameters influence on mechanical properties of structural steels

OpenAIRE

L.A. Dobrzański; R. Honysz

2009-01-01

Purpose: This paper presents Neuro-Lab. It is an authorship programme, which use algorithms of artificial intelligence for structural steels mechanical properties estimation.Design/methodology/approach: On the basis of chemical composition, parameters of heat and mechanical treatment and elements of geometrical shape and size this programme has the ability to calculate the mechanical properties of examined steel and introduce them as raw numeric data or in graphic as influence charts. Possibl...

Influence of Fiber Volume Fraction on the Tensile Properties and Dynamic Characteristics of Coconut Fiber Reinforced Composite

OpenAIRE

Izzuddin Zaman; Al Emran Ismail; Muhamad Khairudin Awang

2011-01-01

The utilization of coconut fibers as reinforcement in polymer composites has been increased significantly due to their low cost and high specific mechanical properties. In this paper, the mechanical properties and dynamic characteristics of a proposed combined polymer composite which consist of a polyester matrix and coconut fibers are determined. The influence of fibers volume fraction (%) is also evaluated and composites with volumetric amounts of coconut fiber up to 15% are fabricated. In ...

The influences of N-acetyl cysteine (NAC) on the cytotoxicity and mechanical properties of Poly-methylmethacrylate (PMMA)-based dental resin.

Science.gov (United States)

Jiao, Yang; Ma, Sai; Li, Jing; Shan, Lequn; Yang, Yanwei; Li, Meng; Chen, Jihua

2015-01-01

Objectives. This study aimed to investigate the influences of N-acetyl cysteine (NAC) on cytotoxicity and mechanical properties of Poly-methylmethacrylate (PMMA) dental resins. Methods. Experimental PMMA resin was prepared by incorporating various concentrations of NAC (0, 0.15, 0.3, 0.6 and 0.9 wt.%). MTT assay was performed to investigate viability of human dental pulp cells after exposure to extract of PMMA resin with or without NAC. Cell adhesion on resin specimens was examined with scanning electron microscopy. Degree of conversion was studied with Fourier Transform Infrared Spectroscopy (FTIR). Flexural strength, microhardness and surface roughness was evaluated using a universal testing machine, microhardness tester and optical profilometer, respectively. Results. Incorporation of NAC into PMMA resin significantly reduced its cytotoxicity and enhanced cell adhesion on its surface. NAC induced negative influences on the mechanical and physical properties of PMMA resin in a dose-dependent manner. The degree of conversion for all experimental PMMA resins reached as high as 72% after 24 h of polymerization. All the tested properties were maintained when the concentration of incorporated NAC was 0.15 wt.%. Conclusion. The addition of 0.15 wt.% NAC remarkably improved biocompatibility of PMMA resin without exerting significant negative influence on its mechanical and physical properties.

Influence of ion size asymmetry on the properties of ionic liquid-vapour interfaces

International Nuclear Information System (INIS)

Bresme, Fernando; Gonzalez-Melchor, Minerva; Alejandre, Jose

2005-01-01

The influence of ion size asymmetry on the properties of ionic liquid-vapour interfaces is investigated using molecular dynamics simulations of the soft primitive model. Ion size asymmetry results in charge separation at the liquid-vapour interface and therefore in a local violation of the electroneutrality condition. For moderate size asymmetries the electrostatic potential at the interface can reach values of the order of 0.1 V. Size asymmetry plays a very important role in determining ion adsorption at the liquid-vapour interface of ionic mixtures. The interfacial adsorption of the bigger component results in an increase of the electrostatic potential, and a reduction of the interfacial surface tension. Our results show that ionic mixtures provide a very efficient way to tune the electrostatics and surface properties of ionic liquid-vapour interfaces

Influence of ion size asymmetry on the properties of ionic liquid-vapour interfaces

Energy Technology Data Exchange (ETDEWEB)

Bresme, Fernando [Department of Chemistry, Imperial College London, London SW7 2AZ (United Kingdom); Gonzalez-Melchor, Minerva [Departamento de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, Avenida San Rafael Atlixco 186, Colonia Vicentina, 09340 Mexico D.F. (Mexico); Alejandre, Jose [Departamento de QuImica, Universidad Autonoma Metropolitana-Iztapalapa, Avenida San Rafael Atlixco 186, Colonia Vicentina, 09340 Mexico D.F. (Mexico)

2005-11-16

The influence of ion size asymmetry on the properties of ionic liquid-vapour interfaces is investigated using molecular dynamics simulations of the soft primitive model. Ion size asymmetry results in charge separation at the liquid-vapour interface and therefore in a local violation of the electroneutrality condition. For moderate size asymmetries the electrostatic potential at the interface can reach values of the order of 0.1 V. Size asymmetry plays a very important role in determining ion adsorption at the liquid-vapour interface of ionic mixtures. The interfacial adsorption of the bigger component results in an increase of the electrostatic potential, and a reduction of the interfacial surface tension. Our results show that ionic mixtures provide a very efficient way to tune the electrostatics and surface properties of ionic liquid-vapour interfaces.

AMINOSILICA NANO- AND SUBMICROSPHERES: ANALYSIS OF FACTORS INFLUENCING MORPHOLOGY, STRUCTURE AND PROPERTIES

Directory of Open Access Journals (Sweden)

Inna Melnyk

2014-06-01

Full Text Available Current paper focuses on the analysis of influence of main factors (stages of the synthesis, the ratio of the reacting components, the order of their introduction, the concentration of water and ammonia, the synthesis temperature on the morphology, size and content of functional groups of aminosilicanano- and submicrospheres. The recommendations for the synthesis of particles with predetermined properties were done. It is shown, that the ratio of the reacting components mainly affects the content of 3-aminopropyl functional groups and the temperature of the hydrolytic polycondensation reaction - the size of the particles.

The influence of Ga{sup +} irradiation on the transport properties of mesoscopic conducting thin films

Energy Technology Data Exchange (ETDEWEB)

Barzola-Quiquia, J; Dusari, S; Bridoux, G; Bern, F; Molle, A; Esquinazi, P, E-mail: j.barzola@physik.uni-leipzig.de, E-mail: esquin@physik.uni-leipzig.de [Division of Superconductivity and Magnetism, Universitaet Leipzig, Linnestrasse 5, D-04103 Leipzig (Germany)

2010-04-09

We studied the influence of 30 keV Ga{sup +}-ions-commonly used in focused-ion-beam (FIB) devices-on the transport properties of thin crystalline graphite flakes, and La{sub 0.7}Ca{sub 0.3}MnO{sub 3} and Co thin films. The changes in electrical resistance were measured in situ during irradiation and also the temperature and magnetic field dependence before and after irradiation. Our results show that the transport properties of these materials strongly change at Ga{sup +} fluences much below those used for patterning and ion-beam-induced deposition (IBID), seriously limiting the use of FIB when the intrinsic properties of the materials of interest are of importance. We present a method that can be used to protect the sample as well as to produce selectively irradiation-induced changes.

Influence of delta ferrite on mechanical and creep properties of steel P92

Energy Technology Data Exchange (ETDEWEB)

Mohyla, Petr [VSB - Technical Univ. of Ostrava (Czech Republic). Faculty of Mechanical Engineering; Kubon, Zdenek [Material and Metallurgical Research Ltd., Ostrava (Czech Republic)

2010-07-01

This article presents some new results obtained during research of chromium modified steel P92. This steel is considered the best modified 9-12% Cr steel for the construction of modern power plants with ultra-super-critical steam parameters. High creep rupture strength of steel P92 is characterized by its chemical composition and by microstructure as well. Optimal microstructure of steel P92 is ideally composed of homogeneous martensite and fine dispersion of secondary particles. During the research program one P92 heat with an occurrence of about 20% delta ferrite was produced. The article describes the microstructure of the heat in various modes of heat treatment, as well as the results of mechanical properties tests at room temperature and also creep test results. The results are confronted with properties of other heats that have no delta ferrite. The relevance is on the significant difference while comparing of creep test results. The comparison of results brings conclusions, defining influence of delta ferrite on mechanical and creep properties of P92 steel. (orig.)

Influence of dense plasma on the energy levels and transition properties in highly charged ions

Science.gov (United States)

Chen, Zhan-Bin; Hu, Hong-Wei; Ma, Kun; Liu, Xiao-Bin; Guo, Xue-Ling; Li, Shuang; Zhu, Bo-Hong; Huang, Lian; Wang, Kai

2018-03-01

The studies of the influence of plasma environments on the level structures and transition properties for highly charged ions are presented. For the relativistic treatment, we implemented the multiconfiguration Dirac-Fock method incorporating the ion sphere (IS) model potential, in which the plasma screening is taken into account as a modified interaction potential between the electron and the nucleus. For the nonrelativistic treatment, analytical solutions of the Schrödinger equation with two types of the IS screened potential are proposed. The Ritz variation method is used with hydrogenic wave function as a trial wave function that contains two unknown variational parameters. Bound energies are derived from an energy equation, and the variational parameters are obtained from the minimisation condition of the expectation value of the energy. Numerical results for hydrogen-like ions in dense plasmas are presented as examples. A detailed analysis of the influence of relativistic effects on the energy levels and transition properties is also reported. Our results are compared with available results in the literature showing a good quantitative agreement.

Influence of soil properties on the bioaccumulation and effects of arsenic in the earthworm Eisenia andrei

NARCIS (Netherlands)

Romero Freire, A.; Martin Peinado, F.J.; Diez Ortiz, M.; van Gestel, C.A.M.

2015-01-01

This study aimed at assessing the influence of soil properties on the uptake and toxicity effects of arsenic in the earthworm Eisenia andrei exposed for 4 weeks to seven natural soils spiked with different arsenic concentrations. Water-soluble soil concentrations (AsW) and internal As concentrations

Transitional grain boundary structures and the influence on thermal, mechanical and energy properties from molecular dynamics simulations

International Nuclear Information System (INIS)

Burbery, N.J.; Das, R.; Ferguson, W.G.

2016-01-01

The thermo-kinetic characteristics that dictate the activation of atomistic crystal defects significantly influence the mechanical properties of crystalline materials. Grain boundaries (GBs) primarily influence the plastic deformation of FCC metals through their interaction with mobile dislocation defects. The activation thresholds and atomic mechanisms that dictate the thermo-kinetic properties of grain boundaries have been difficult to study due to complex and highly variable GB structure. This paper presents a new approach for modelling GBs which is based on a systematic structural analysis of metastable and stable GBs. GB structural transformation accommodates defect interactions at the interface. The activation energy for such structural transformations was evaluated with nudged elastic band analysis of bi-crystals with several metastable 0 K grain boundary structures in pure FCC Aluminium (Al). The resultant activation energy was used to evaluate the thermal stability of the metastable grain boundary structures, with predictions of transition time based on transition state theory. The predictions are in very good agreement with the minimum time for irreversible structure transformation at 300 K obtained with molecular dynamics simulations. Analytical methods were used to evaluate the activation volume, which in turn was used to predict and explain the influence of stress and strain rate on the thermal and mechanical properties. Results of molecular dynamics simulations show that the GB structure is more closely related to the elastic strength at 0 K than the GB energy. Furthermore, the thermal instability of the GB structure directly influences the relationship between bi-crystal strength, temperature and strain rate. Hence, theoretically consistent models are established on the basis of activation criteria, and used to make predictions of temperature-dependent yield stress at a low strain rate, in agreement with experimental results.

Low cloud properties influenced by cosmic rays

Science.gov (United States)

Marsh; Svensmark

2000-12-04

The influence of solar variability on climate is currently uncertain. Recent observations have indicated a possible mechanism via the influence of solar modulated cosmic rays on global cloud cover. Surprisingly the influence of solar variability is strongest in low clouds (climate on Earth.

Characterization of physicochemical properties of hydroxypropyl methylcellulose (HPMC) type 2208 and their influence on prolonged drug release from matrix tablets

OpenAIRE

Devjak Novak, Sabina; Šporar, Elena; Vrečer, Franc; Baumgartner, Saša

2015-01-01

The key physicochemical properties of functional excipients should be identified, and the influence of their variability on the properties of the final dosage form should be evaluated during the development phase. Excipients produced by different manufacturers and/or by differentb manufacturing processes should have comparable properties. Hydroxypropyl methylcellulose (HPMC) with a high molecular weight is a functional excipient often used in solid matrix systems with prolonged release of act...

Investigating the influence of infill percentage on the mechanical properties of fused deposition modelled ABS parts

Directory of Open Access Journals (Sweden)

Kenny Álvarez

2016-09-01

Full Text Available 3D printing is a manufacturing process that is usually used for modeling and prototyping. One of the most popular printing techniques is fused deposition modeling (FDM, which is based on adding melted material layer by layer. Although FDM has several advantages with respect to other manufacturing materials, there are several problems that have to be faced. When setting the printing options, several parameters have to be taken into account, such as temperature, speed, infill percentage, etc. Selecting these parameters is often a great challenge for the user, and is generally solved by experience without considering the influence of variations in the parameters on the mechanical properties of the printed parts.This article analyzes the influence of the infill percentage on the mechanical properties of ABS (Acrylonitrile Butadiene Styrene printed parts. In order to characterize this influence, test specimens for tensile strength and Charpy tests were printed with a Makerbot Replicator 2X printer, in which the infill percentage was varied but the rest of the printing parameters were kept constant. Three different results were analyzed for these tests: tensile strength, impact resistance, and effective printing time. Results showed that the maximum tensile force (1438N and tensile stress (34,57MPa were obtained by using 100% infill. The maximum impact resistance, 1,55J, was also obtained with 100% infill. In terms of effective printing time, results showed that printing with an infill range between 50% and 98% is not recommended, since the effective printing time is higher than with a 100% infill and the tensile strength and impact resistance are smaller. In addition, in comparing the results of our analysis with results from other authors, it can be concluded that the printer type and plastic roll significantly influence the mechanical properties of ABS parts.

The influence of interlayer interactions on the mechanical properties of polymeric nanocomposites

Directory of Open Access Journals (Sweden)

Jabbarzadeh Mehrdad

2015-01-01

Full Text Available In this paper the influence of types of interlayer interactions on the elastic modules of multilayer graphene sheets (GS and nanocomposites is studied. The modeling and investigation of mechanical properties of graphite layers are performed using molecular mechanics (MM method. Initially, due to improving the model and decreasing the amount of computations, three types of elements such as beam, linear spring and nonlinear spring are used. To continue, the mechanical properties of multilayers and nanocomposites are compared using three types of interlayer interactions. Initially, nonlinear spring defined by Leonard Jones potential is used to define interlayer interactions (ordinary case. To continue, linear spring with certain stiffness, to obtain an equal linear spring and also to investigate the ultimate capacity of interlayer interactions in the force translation, by increasing the stiffness of linear springs, is employed (chemical change. Then once by omitting all Van der Waals interactions and defects creation in graphite layers, they are devoted to create covalent interlayer interactions (using Morse potential and another time, Van der Waals and covalent interlayer interactions are created spontaneously to study the properties of multilayers and nanocomposites (functionalization. The results are compared with other available literatures in this case to validate the modeling.

The influence of blend ratio on the morphology, mechanical, thermal, and rheological properties of PP/LDPE blends

CSIR Research Space (South Africa)

Mofokeng, TG

2016-10-01

Full Text Available ratio and morphology influence impact strength and elongation at break, and the result demonstrates that the 80/20 PP/LDPE blend offers a balance among the mechanical and material properties that are essential for flexible packaging applications....

Soil physical properties influencing the fitting parameters in Philip and Kostiakov infiltration models

International Nuclear Information System (INIS)

Mbagwu, J.S.C.

1994-05-01

Among the many models developed for monitoring the infiltration process those of Philip and Kostiakov have been studied in detail because of their simplicity and the ease of estimating their fitting parameters. The important soil physical factors influencing the fitting parameters in these infiltration models are reported in this study. The results of the study show that the single most important soil property affecting the fitting parameters in these models is the effective porosity. 36 refs, 2 figs, 5 tabs

Ionic Liquid as Surfactant Agent of Hydrotalcite: Influence on the Final Properties of Polycaprolactone Matrix

Directory of Open Access Journals (Sweden)

Luanda Chaves Lins

2018-01-01

Full Text Available This paper reports the surface treatment of layered double hydroxide (LDH by using ionic liquid (IL composed of phosphonium cation combined with 2-ethylhexanoate (EHT counter anion as surfactant agent. Then, different amounts (1, 3, 5 and 7 wt % of thermally stable organically modified LDH (up to 350 °C denoted LDH-EHT were incorporated into polycaprolactone (PCL matrix by mechanical milling. The influence of LDH-EHT loading has been investigated on the physical properties, such as the thermal and barrier properties, as well as the morphologies of the resulting nanocomposites. Thus, intercalated or microcomposite morphologies were obtained depending on the LDH-EHT loading, leading to significant reduction of the diffusion coefficient respect to water vapor. The modulation of barrier properties, using low functionalized filler amount, is a very important aspect for materials in packaging applications.

The influence of ventilated façade on sound insulation properties of envelope walls

Directory of Open Access Journals (Sweden)

Fišarová Zuzana

2017-01-01

Full Text Available Presented article deals with sound insulation properties of timber structures’ envelope walls. Particularly, the influence of heavy board ventilated façade on laboratory airborne sound insulation R and Rw in dB was studied. The installation method and gaps between façade boards can cause building defects originating in overrating the influence of ventilated cladding on envelope wall acoustic parameters. Real constructions were built for the experimental purposes and measurements, one with gaps between boards and one with simply eliminated gaps for mutual comparison. The results obtained were processed to make tables and graphs and to derive recommendations for the design of this type of constructions involving the general installation method of façade boards. Detailed results are depicted in conclusions.

The influence of radiation and microwave agents on some properties of haemopoietic stem cells

International Nuclear Information System (INIS)

Barakina, N.F.; Rakhmanina, O.N.

1985-01-01

Sublethal irradiation of donors leads to a change in some properties of bone marrow haemopoetic stem cells (HSC) during the exponential growth (days 1-8) of the syngeneic recipients in the spleen. They are: an increase in the rate of proliferation, a slight reduction in time of the population doubling, and a tendency toward an increase in the percentage of cells settled in the spleen after transplantation. Theses changes in the properties of HSC provide a more rapid repopulation thereof as compared to HSC of intact mice. In all appearance, a pretreatment of donors with AET and 2ADT does not influence the HSC changes induced by radiation, and, at the same time, retains the number of HSC at a high level

Influence of copper on morphologic properties of roots of Vicia faba

Energy Technology Data Exchange (ETDEWEB)

Kostal, L

1973-01-01

Relatively few papers deal with anatomic-morphological changes taking place due to deficiency or toxical influence of copper. There are few papers relating to the influence of higher copper concentrations on morphological properties. Comparative studies investigating copper toxicity have not been worked out in detail. Experiments determining toxicity have been carried out on different substrates. This substrate is very important since there is the question of the bond of copper with various substances, which are found in substrate and which reduce, to a certain extent, the toxicity of copper. Maximum toxicity can be found out in aqueous and sand cultures. High toxicity of copper ions depends, to a large extent, on the stability of its complex compounds, which results in the stability of copper to separate other metals from different compounds. In this way copper inactivates enzymes and various biologically active substances. The problem of toxicity has been widely studied. The author considers the concentration of 0.5 mg Cu/l is a limit of copper toxicity with oat, whereas the concentration of 0.25 mg is toxical for the sprouts of citruses. It is obvious that the limit of toxicity cannot be exactly determined since there are several factors involved (sort of plant, use of cultivation method etc.) This paper was aimed at finding out the influence of higher copper concentrations on morphological changes of roots, stem and leaves of bean Vicia faba.

Characterization of physicochemical properties of hydroxypropyl methylcellulose (HPMC) type 2208 and their influence on prolonged drug release from matrix tablets.

Science.gov (United States)

Devjak Novak, S; Šporar, E; Baumgartner, S; Vrečer, F

2012-07-01

The key physicochemical properties of functional excipients should be identified, and the influence of their variability on the properties of the final dosage form should be evaluated during the development phase. Excipients produced by different manufacturers and/or by different manufacturing processes should have comparable properties. Hydroxypropyl methylcellulose (HPMC) with a high molecular weight is a functional excipient often used in solid matrix systems with prolonged release of active pharmaceutical ingredients (API). This study investigates whether HPMC manufactured by two manufacturers using different chemical procedures differs in particle-size distribution, particle shape, particle morphology, chemical composition, and dissolution of diclofenac sodium as a model drug. NIR spectroscopy was introduced and calibration models were developed to detect physical differences among HPMC batches from two different origins. The physical differences between HPMC samples were additionally confirmed with scanning electron microscopy (SEM), gas chromatography (GC) measurements, and dissolution testing of hydrophilic matrix tablets. Our results prove that, even if HPMC polymers manufactured from two different sources comply with the pharmacopeial specification, they significantly differ in physicochemical properties and thus influence the properties of the formulated dosage forms. Copyright © 2012 Elsevier B.V. All rights reserved.

Influence of Nd content on magnetic properties of amorphous FeB alloys

Science.gov (United States)

Hassanain, N.; Lassri, H.; Krishnan, R.; Berrada, A.

The influence of the addition of Nd on the magnetic properties ( TC, M0, Hc, …) of FeB amorphous alloys is investigated. Using Chudnovsky's model we have analyzed our data and obtained some fundamental parameters. For instance, with the addition of Nd atoms the local anisotropy is 2.0 × 10 7 erg cm -3 and the exchange constant. A decreases from 38 × 10 -8 to 21.7 × 10 -8 erg cm -1 as the Nd concentration increases from 0 to 15%. The ferromagnetic exchange correlation length also decreases drastically from 353 to 80 Å in the same concentration range.

Influence of HIP pressure on tensile properties of a 14Cr ODS ferritic steel

Energy Technology Data Exchange (ETDEWEB)

Oksiuta, Z., E-mail: z.oksiuta@pb.edu.pl [Bialystok Technical University, Mechanical Department, Wiejska 45c, 15-351 Bialystok (Poland); Ozieblo, A.; Perkowski, K.; Osuchowski, M. [Institute of Ceramics and Building Materials, Postępu 9, 02-676 Warsaw (Poland); Lewandowska, M. [Warsaw University of Technology, Woloska 141, 02-504 Warsaw (Poland)

2014-02-15

Highlights: • The HIPping parameters of the 14Cr–2W–0.3Ti–0.3Y{sub 2}O{sub 3} ODS steel powder were investigated. • The density and microstructure of the tested specimens after HIPping were studied. • The mechanical properties, high temperature tensile tests, were performed. • Residual porosity was observed in all tested specimens. • HIPping pressure has negligible influence on the strength of the ODS steel however improves material ductility. - Abstract: An oxide dispersion strengthened ferritic steel with a nominal composition of Fe–14Cr–2W–0.3Ti–0.3Y{sub 2}O{sub 3} (in wt.%) was consolidated by hot isostatic pressing at 1150 °C under various pressures in the range of 185–300 MPa for 3 h. The microstructure, microhardness and high temperature tensile properties of the steel were investigated. With increasing compaction pressure the density of specimens also increased, however OM and SEM observations revealed residual porosity in all tested specimens and similar ferritic microstructure with bimodal-like grains and numerous of large oxide particles, located at the grain boundaries. Mechanical testing revealed that compaction pressure has negligible influence on the hardness and tensile strength of the ODS steel, however improves the material ductility.

Influence of HIP pressure on tensile properties of a 14Cr ODS ferritic steel

International Nuclear Information System (INIS)

Oksiuta, Z.; Ozieblo, A.; Perkowski, K.; Osuchowski, M.; Lewandowska, M.

2014-01-01

Highlights: • The HIPping parameters of the 14Cr–2W–0.3Ti–0.3Y 2 O 3 ODS steel powder were investigated. • The density and microstructure of the tested specimens after HIPping were studied. • The mechanical properties, high temperature tensile tests, were performed. • Residual porosity was observed in all tested specimens. • HIPping pressure has negligible influence on the strength of the ODS steel however improves material ductility. - Abstract: An oxide dispersion strengthened ferritic steel with a nominal composition of Fe–14Cr–2W–0.3Ti–0.3Y 2 O 3 (in wt.%) was consolidated by hot isostatic pressing at 1150 °C under various pressures in the range of 185–300 MPa for 3 h. The microstructure, microhardness and high temperature tensile properties of the steel were investigated. With increasing compaction pressure the density of specimens also increased, however OM and SEM observations revealed residual porosity in all tested specimens and similar ferritic microstructure with bimodal-like grains and numerous of large oxide particles, located at the grain boundaries. Mechanical testing revealed that compaction pressure has negligible influence on the hardness and tensile strength of the ODS steel, however improves the material ductility

Information-Theoretic Properties of Auditory Sequences Dynamically Influence Expectation and Memory.

Science.gov (United States)

Agres, Kat; Abdallah, Samer; Pearce, Marcus

2018-01-01

A basic function of cognition is to detect regularities in sensory input to facilitate the prediction and recognition of future events. It has been proposed that these implicit expectations arise from an internal predictive coding model, based on knowledge acquired through processes such as statistical learning, but it is unclear how different types of statistical information affect listeners' memory for auditory stimuli. We used a combination of behavioral and computational methods to investigate memory for non-linguistic auditory sequences. Participants repeatedly heard tone sequences varying systematically in their information-theoretic properties. Expectedness ratings of tones were collected during three listening sessions, and a recognition memory test was given after each session. Information-theoretic measures of sequential predictability significantly influenced listeners' expectedness ratings, and variations in these properties had a significant impact on memory performance. Predictable sequences yielded increasingly better memory performance with increasing exposure. Computational simulations using a probabilistic model of auditory expectation suggest that listeners dynamically formed a new, and increasingly accurate, implicit cognitive model of the information-theoretic structure of the sequences throughout the experimental session. Copyright © 2017 Cognitive Science Society, Inc.

THE INFLUENCE OF RECUPIRATION’S METHODS OF GRAPHITE TO PROPERTIES OF SYNTHESIZED DIAMONDS

Directory of Open Access Journals (Sweden)

G. P. Bogatyreva

2015-03-01

Full Text Available The graphite’s waste can be used for synthesis of diamonds. It is established, that activation of graphite’s waste essential influence on a degree of transition of graph-ite in diamond and their physico-chemical properties. The activation of th graphite’s waste changes essentially their absorption and structural characteristics and to a great extent affect the characteristics of synthesized diamond. Thermal activation of graphite’s waste leads to that are synthesized, basically, diamond micropowders, and electrochemical — diamond grinding powders.

Influence of cellulose fibers on structure and properties of fiber reinforced foam concrete

Directory of Open Access Journals (Sweden)

Fedorov Valeriy

2018-01-01

Full Text Available One of the promising means of foamed concrete quality improvement is micro-reinforcement by adding synthetic and mineral fibers to the base mix. This research is the first to investigate peculiarities of using recycled cellulose fiber extracted from waste paper for obtaining fiber reinforced foam concrete. The paper presents results of experimental research on the influence of cellulose fibers on structure and properties of fiber reinforced foam concrete by using methods of chemical analysis and scanning electron microscopy. The research determines peculiarities of new formations appearance and densification of binder hydration products in the contact zone between fiber and cement matrix, which boost mechanical strength of fiber reinforced foam concrete. Physico-mechanical properties of fiber reinforced foam concrete were defined depending on the amount of recycled cellulose fiber added to the base mix. It was found that the use of recycled cellulose fibers allows obtaining structural thermal insulating fiber reinforced foam concretes of non-autoclaved hardening of brand D600 with regard to mean density with the following improved properties: compressive strength increased by 35% compared to basic samples, higher stability of foamed concrete mix and decreased shrinkage deformation.

The influence of natural pozzolana mineralogical composition in the properties of blended cement

Directory of Open Access Journals (Sweden)

Gener Rizo, M.

2002-09-01

Full Text Available The pozzolana activity is the main property of the active additions but, in order to select them, we have to consider - between other factors- its mineralogical composition with a great influence, not only in the active component, but also in other cement properties. In the present work we have studied 4 different Cuban natural pozzolanes, characterized with the help of X ray diffraction and with thermic and chemical analysis. The pozzolanic activity was also evaluated through a chemical and physicomechanic method. Some cements were prepared with different contents of each one of the pozzolanics, and analysed their physicomechanic and chemical properties. Finally, we found that the pozzolanics mineralogical composition has a great influence in the pozzolanic activity and in the properties of mixed cements. Also we found that it 5 possible to obtain the best resistances in the time and the smaller needs of water when the vitreous phase prevail in the additions.

La actividad puzolánica es la propiedad fundamental de las adiciones activas, pero para la selección de la misma se debe considerar, entre otros factores, su composición mineralógica, que influye no sólo en los constituyentes activos, sino también en muchas propiedades de los cementos. En el presente trabajo, como material puzolánico se estudiaron 4 puzolanas naturales cubanas, las cuales fueron caracterizadas mediante difracción de Rayos X, análisis térmico y análisis químico; se evaluó, además, la actividad puzolánica mediante un método químico y otro físico-mecánico. Se prepararon cementos con diferentes contenidos de cada una de las puzolanas y se analizaron sus propiedades químicas y físico-mecánicas. Se concluye que la composición mineralógica de las puzolanas influye de forma determinante en la actividad puzolánica y en las propiedades de los cementos mezclados; que los mejores desarrollos de resistencias en el tiempo y los menores requerimientos

Influence of low-temperature annealing on magnetic properties of (Nd0.625Ni0.375)85Al15 metallic glass

International Nuclear Information System (INIS)

Xu Feng; Wang Zhiming; Chen Guang; Jiang Jianzhong; Du Youwei

2008-01-01

After a review of the selection process of (Nd 0.625 Ni 0.375 ) 85 Al 15 as a metallic glass with a relatively high glass-forming ability, we investigate the influences of its phase transitions by duplicating the heating process of the isochronal thermal analysis with low-temperature annealings. The structure, thermal stability and magnetic properties are characterized. And the influences on magnetic properties are particularly discussed with emphasis. Both the annealing processes, to the glass-transition temperature and to the onset temperature of crystallization, bring about a higher coercivity of the sample and a higher freezing temperature of the spin-glass-state. For the sample annealed to the onset temperature of crystallization, the influence is quite obvious and is ascribed to the formation of ferrimagnetic Nd 7 Ni 3 phase, as detected by XRD. For the sample annealed to the glass-transition temperature, the indistinct influence is further identified with the analysis of the frequency dependence of the spin-glass-state, and it is mainly attributed to the change of the short-range order in the amorphous matrix

The influence of oxidation properties on the electron emission characteristics of porous silicon

International Nuclear Information System (INIS)

He, Li; Zhang, Xiaoning; Wang, Wenjiang; Wei, Haicheng

2016-01-01

Highlights: • Evaluated the oxidation properties of porous silicon from semi-quantitative methods. • Discovered the relationship between oxidation properties and emission characteristics. • Revealed the micro-essence of the electron emission of the porous silicon. - Abstract: In order to investigate the influence of oxidation properties such as oxygen content and its distribution gradient on the electron emission characteristics of porous silicon (PS) emitters, emitters with PS thickness of 8 μm, 5 μm, and 3 μm were prepared and then oxidized by electrochemical oxidation (ECO) and ECO-RTO (rapid thermal oxidation) to get different oxidation properties. The experimental results indicated that the emission current density, efficiency, and stability of the PS emitters are mainly determined by oxidation properties. The higher oxygen content and the smaller oxygen distribution gradient in the PS layer, the larger emission current density and efficiency we noted. The most favorable results occurred for the PS emitter with the smallest oxygen distribution gradient and the highest level of oxygen content, with an emission current density of 212.25 μA/cm"2 and efficiency of 59.21‰. Additionally, it also demonstrates that thick PS layer benefits to the emission stability due to its longer electron acceleration tunnel. The FN fitting plots indicated that the effective emission areas of PS emitters can be enlarged and electron emission thresholds is decreased because of the higher oxygen content and smaller distribution gradient, which were approved by the optical micrographs of top electrode of PS emitters before and after electron emission.

The influence of oxidation properties on the electron emission characteristics of porous silicon

Energy Technology Data Exchange (ETDEWEB)

He, Li [Key Laboratory of Physical Electronics and Devices of the Ministry of Education, Xi’an Jiaotong University, Xi’an 710049 (China); Zhang, Xiaoning, E-mail: znn@mail.xjtu.edu.cn [Key Laboratory of Physical Electronics and Devices of the Ministry of Education, Xi’an Jiaotong University, Xi’an 710049 (China); Wang, Wenjiang [Key Laboratory of Physical Electronics and Devices of the Ministry of Education, Xi’an Jiaotong University, Xi’an 710049 (China); Wei, Haicheng [School of Electrical and Information Engineering, Beifang University of Nationalities, Yinchuan750021 (China)

2016-09-30

Highlights: • Evaluated the oxidation properties of porous silicon from semi-quantitative methods. • Discovered the relationship between oxidation properties and emission characteristics. • Revealed the micro-essence of the electron emission of the porous silicon. - Abstract: In order to investigate the influence of oxidation properties such as oxygen content and its distribution gradient on the electron emission characteristics of porous silicon (PS) emitters, emitters with PS thickness of 8 μm, 5 μm, and 3 μm were prepared and then oxidized by electrochemical oxidation (ECO) and ECO-RTO (rapid thermal oxidation) to get different oxidation properties. The experimental results indicated that the emission current density, efficiency, and stability of the PS emitters are mainly determined by oxidation properties. The higher oxygen content and the smaller oxygen distribution gradient in the PS layer, the larger emission current density and efficiency we noted. The most favorable results occurred for the PS emitter with the smallest oxygen distribution gradient and the highest level of oxygen content, with an emission current density of 212.25 μA/cm{sup 2} and efficiency of 59.21‰. Additionally, it also demonstrates that thick PS layer benefits to the emission stability due to its longer electron acceleration tunnel. The FN fitting plots indicated that the effective emission areas of PS emitters can be enlarged and electron emission thresholds is decreased because of the higher oxygen content and smaller distribution gradient, which were approved by the optical micrographs of top electrode of PS emitters before and after electron emission.

Influence of purity level on the mechanical properties of hot isostatically pressed beryllium

International Nuclear Information System (INIS)

Odegard, B.C. Jr.

1979-09-01

The procurement of a quantity of ultra-pure beryllium powder combined with special handling from powder to billet form resulted in the fabrication of high purity beryllium. The mechanical properties of these billets were contrasted to those of commercial grade billets to determine the influence of impurities and powder processing. The tensile test results show that the strength values are primarily dependent on the grain size in a behavior predictable by the Hall-Petch relationship. Only a fraction of the strength differential can be attributed to metallic impurities in solution. The grain size is controlled by the powder size distribution. The ductility is dominated by both grain size and oxide content. The fine grained, low oxide billets exhibited the highest ductilities. There is evidence to suggest that oxide distribution has a large influence on the ductility. The fracture toughness was highest for the high purity beryllium billets

Influence analysis of structural parameters on electromagnetic properties of HTS linear induction motor

International Nuclear Information System (INIS)

Zhao, J.; Zheng, T.Q.; Zhang, W.; Fang, J.; Liu, Y.M.

2011-01-01

A new type high temperature superconductor linear induction motor is designed and analyzed as a prototype to ensure applicability aimed at industrial motors. Made of Bi-2223/Ag, primary windings are distributed with the double-layer concentrated structure. The motor is analyzed by 2D electromagnetic Finite Element Method to get magnetic field distribution, thrust force, vertical force and so on. The critical current of motor and the electromagnetic force are mostly decided by the leakage flux density of primary slot and by the main magnetic flux and eddy current respectively. The structural parameters of motor have a great influence on the distribution of magnetic field. Under constant currents, the properties of motor are analyzed with different slot widths, slot heights and winding turns. The properties of motor, such as the maximum slot leakage flux density, motor thrust and motor vertical force, are analyzed with different structural parameters.

The influence of filler surface modification on mechanical and material properties of layered double hydroxide -containing polypropylene composites

CSIR Research Space (South Africa)

Moyo, Lumbidzani

2017-03-01

Full Text Available The processing and properties of layered double hydroxides (LDHs)-containing polypropylene (PP) composites have been studied extensively. However, no detailed studies have reported on how stearic acid (SA)-intercalated and SA-coated LDHs influence...

Crystallisation of Gypsum and Prevention of Foaming in Wet Flue Gas Desulphurisation (FGD) Plants

DEFF Research Database (Denmark)

Hansen, Brian Brun

The aim of this project is to investigate two operational problems, which have been experienced during wet flue gas desulphurisation (FGD) operation, i.e. poor gypsum dewatering properties and foaming. The results of this work can be used for the optimization of wet FGD-plants in terms of reliabi......The aim of this project is to investigate two operational problems, which have been experienced during wet flue gas desulphurisation (FGD) operation, i.e. poor gypsum dewatering properties and foaming. The results of this work can be used for the optimization of wet FGD-plants in terms....... Experiments in a falling film wet FGD pilot plant have shown a strong non-linear behaviour (in a ln(n(l)) vs. l plot) at the lower end of the particle size range, compared to the well-known linear “mixed suspension mixed product removal (MSMPR)” model. A transient population balance model, fitted...

Proceedings of the 2. international oil sands tailings conference

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-01

The tailings produced by oil sands extraction processes pose significant threats to the surrounding environment in addition to releasing greenhouse gases (GHGs) into the atmosphere. Recent directives have been established to reduce the amount of tailings produced at oil sands operations, and to ensure that tailings ponds are reclaimed in the most effective manner. This conference provided a forum for researchers and industry experts to discuss issues related to the management and reclamation of oil sands tailings. New technologies for dewatering tailings ponds were presented, and methods of analyzing the chemical properties of tailings were reviewed. The conference was divided into the following 7 sessions: (1) tailings properties, (2) tailings dewatering, (3) new concepts, (4) water and chemistry, (5) soft tailings stabilization and reclamation, (6) water treatment, and (7) new concepts 2. The conference featured 44 presentations, all of which have been catalogued separately for inclusion in this database. tabs., figs.

Influence of the variable thermophysical properties on the turbulent buoyancy-driven airflow inside open square cavities

Science.gov (United States)

Zamora, Blas; Kaiser, Antonio S.

2012-01-01

The effects of the air variable properties (density, viscosity and thermal conductivity) on the buoyancy-driven flows established in open square cavities are investigated, as well as the influence of the stated boundary conditions at open edges and the employed differencing scheme. Two-dimensional, laminar, transitional and turbulent simulations are obtained, considering both uniform wall temperature and uniform heat flux heating conditions. In transitional and turbulent cases, the low-Reynolds k - ω turbulence model is employed. The average Nusselt number and the dimensionless mass-flow rate have been obtained for a wide and not yet covered range of the Rayleigh number varying from 103 to 1016. The results obtained taking into account variable properties effects are compared with those calculated assuming constant properties and the Boussinesq approximation. For uniform heat flux heating, a correlation for the critical heating parameter above which the burnout phenomenon can be obtained is presented, not reported in previous works. The effects of variable properties on the flow patterns are analyzed.

Influence of nanomaterials on properties of latent heat solar thermal energy storage materials – A review

International Nuclear Information System (INIS)

Raam Dheep, G.; Sreekumar, A.

2014-01-01

Highlights: • Classification of phase change materials. • Studies on phase change properties of various phase change materials. • Influence of nanomaterials on properties of phase change materials. - Abstract: Thermal energy storage system plays a critical role in developing an efficient solar energy device. As far as solar thermal devices are concerned, there is always a mismatch between supply and demand due to intermittent and unpredictable nature of solar radiation. A well designed thermal energy storage system is capable to alleviate this demerit by providing a constant energy delivery to the load. Many research works is being carried out to determine the suitability of thermal energy storage system to integrate with solar thermal gadgets. This review paper summarizes the numerous investigations on latent heat thermal energy storage using phase change materials (PCM) and its classification, properties, selection criteria, potential research areas and studies involved to analyze the thermal–physical properties of PCM

Radioactive slurry waste treatment (2) - surfactants dose effects on filtration

International Nuclear Information System (INIS)

Jung, K. H.; Park, S. K.; Jung, W. S.; Baek, S. T.; Jung, K. J.

1999-01-01

The influence of anionic flocculants on the dewatering of radioactive slurries has been investigated in a laboratory-scale vacuum filtration unit. Simultaneously the influence of certain surfactants has also been investigated. Test results show that the flocculated filter cake generally contains higher residual water than the unflocculated cake. The non-ionic surfactant was effective in reducing the moisture content of the cake

The Influence of Stabilisation on the Structure of Knits and Tensile Properties of Their Yarns

Directory of Open Access Journals (Sweden)

Rasa TREIGIENĖ

2012-12-01

Full Text Available Plated jersey knits of different composition were knitted and stabilised under hydrothermal conditions of 85 °C for 10, 20 or 30 min in steam ambience. The influence of stabilisation duration on knit structure was estimated as well as change of mechanical properties of the yarns. The obtained data show that 10 min of stabilisation influenced markedly the structure of plated jersey knits comparing with the same effect of 20 min and 30 min. The results of specific breaking force of polyester, cotton and wool yarns show decrease in their strength due to knitting and hydrothermal stabilisation processes.DOI: http://dx.doi.org/10.5755/j01.ms.18.4.3096

Influence of attractions on the static and dynamic properties of simulated single and multichain systems

International Nuclear Information System (INIS)

Bishop, M.; Kalos, M.H.; Frisch, H.L.

1983-01-01

The influence of the attractive portion of the Lennard-Jones potential on the statics and dynamics of both single chain and multichain systems is investigated by reptation and molecular dynamics simulations. There is no significant effect at a reduced temperature of 10.0. At a temperature of 1.7 the single chain and multichain system at low densities (0.1) indicate that the attractions cause both the chains to be significantly more compact and a slowing of the time autocorrelation functions of the square of the end-to-end distance and radius of gyration. At a moderate density of 0.5, the attractions have almost no effect on the static structure, but they still influence the dynamic properties

Influence of the Pyrolysis Temperature on Sewage Sludge Product Distribution, Bio-Oil, and Char Properties

DEFF Research Database (Denmark)

Trinh, Ngoc Trung; Jensen, Peter Arendt; Dam-Johansen, Kim

2013-01-01

Fast pyrolysis may be used for sewage sludge treatment with the advantages of a significant reduction of solid waste volume and production of a bio-oil that can be used as fuel. A study of the influence of the reaction temperature on sewage sludge pyrolysis has been carried out using a pyrolysis...... of 392 g/mol, and metal concentrations lower than 0.14 wt % on a dry basis (db). Less optimal oil properties with respect to industrial applications were observed for oil samples obtained at 475 and 625 °C. Char properties of the 575 °C sample were an ash content of 81 wt % and a HHV of 6.1 MJ/kg db...

Influence of pulse electric current on structure and superconducting properties of high temperature superconductor

International Nuclear Information System (INIS)

Rajchenko, A.I.; Flis, A.A.; Chernenko, L.I.; Kryuchkova, N.I.

1998-01-01

The influence of high-density pulse current treatment at room temperature on structure and superconducting properties of HTSC Y Ba 2 Cu 3 O x ceramics is studied. The structures of the samples are found to undergo appreciable changes as the density of pulse current is gradually increased from its minimum value; as a certain threshold value is attained, there occurs a melting-off of coarse grains with a partial destroying of intergrain contact areas followed by superconductivity loss. A further increase in the treatment current density results in a restoration of the superconducting properties probably due to the occurrence of aligned-with-current superconducting bridges between the melted-off grains. The superconducting transition temperature in the samples does not charge but subsequent thermal treatment causes this temperature to increase

Influence of intercritical austempering on the microstructure and mechanical properties of austempered ductile cast iron (ADI)

International Nuclear Information System (INIS)

Panneerselvam, Saranya; Putatunda, Susil K.; Gundlach, Richard; Boileau, James

2017-01-01

The focus of this investigation was to examine the influence of intercritical austempering process on the microstructure and mechanical properties of low-alloyed austempered ductile cast iron (ADI). The investigation also examined the influence of intercritical austempering process on the plane strain fracture toughness of the material. The effect of both austenitization and austempering temperature on the microstructure and mechanical properties was examined. The microstructural analysis was carried out using optical microscopy, scanning electron microscopy and X-ray diffraction. The test results indicate that by intercritical austempering it is possible to produce proeutectoid ferrite in the matrix microstructure. Lower austenitizing temperature produces more proeutectoid ferrite in the matrix. Furthermore, the yield, tensile strength and the fracture toughness of the ADI decreases with decrease in austenitizing temperature. A considerable increase in ductility was observed in the samples with higher proeutectoid ferrite content. The fracture surfaces of the ADI samples revealed that dimple ductile fracture produced higher fracture toughness of 60±5 MPa√m in this intercritically austempered ADI.

Influence of intercritical austempering on the microstructure and mechanical properties of austempered ductile cast iron (ADI)

Energy Technology Data Exchange (ETDEWEB)

Panneerselvam, Saranya [Wayne State University, Detroit, MI (United States); Putatunda, Susil K., E-mail: sputa@eng.wayne.edu [Wayne State University, Detroit, MI (United States); Gundlach, Richard [Element Materials Technology, MI (United States); Boileau, James [Ford Motor Company, Dearborn, MI (United States)

2017-05-10

The focus of this investigation was to examine the influence of intercritical austempering process on the microstructure and mechanical properties of low-alloyed austempered ductile cast iron (ADI). The investigation also examined the influence of intercritical austempering process on the plane strain fracture toughness of the material. The effect of both austenitization and austempering temperature on the microstructure and mechanical properties was examined. The microstructural analysis was carried out using optical microscopy, scanning electron microscopy and X-ray diffraction. The test results indicate that by intercritical austempering it is possible to produce proeutectoid ferrite in the matrix microstructure. Lower austenitizing temperature produces more proeutectoid ferrite in the matrix. Furthermore, the yield, tensile strength and the fracture toughness of the ADI decreases with decrease in austenitizing temperature. A considerable increase in ductility was observed in the samples with higher proeutectoid ferrite content. The fracture surfaces of the ADI samples revealed that dimple ductile fracture produced higher fracture toughness of 60±5 MPa√m in this intercritically austempered ADI.

The influence of hardening conditions on the properties of masonry cement mortar prisms made in brick moulds

NARCIS (Netherlands)

Bertram, G.; Lourenco, P.B.; Hasseltine, B.A.; Vasconseles, G.

2014-01-01

One aspect of our investigation into the spacing of movement joints involved the short and long term deformation of mortar embedded in masonry. In this research the influence of hardening conditions on the physical and mechanical properties of masonry cement mortar [M5] were studied. Mortar prisms

Influence of vibration on structure rheological properties of a highly concentrated suspension

Science.gov (United States)

Ouriev Uriev, Boris N.; Uriev, Naum B.

2005-08-01

The influence of mechanical vibration on the flow properties of a highly concentrated multiphase food system is explored in this work. An experimental set-up was designed and adapted to a conventional rotational rheometer with precise rheological characterization capability. A number of calibration tests were performed prior to fundamental experiments with a highly concentrated chocolate suspension. Also, the prediction of wall slippage in shear flow under vibration was evaluated. Analysis of the boundary conditions shows that no side effects such as wall slippage or the Taylor effect were present during the shear experiment under vibration. It was found that superposition of mechanical vibration and shear flow radically decreases the shear viscosity. Comparison between reference shear viscosities at specified shear rates and those measured under vibration shows considerable differences in flow properties. Conversion of the behaviour of the concentrated suspension from strongly shear-thinning to Newtonian flow is reported. Also, the appearance of vibration-induced dilatancy as a new phenomenon is described. It is suggested to relate such phenomena to the non-equilibrium between structure formation and disintegration under vibration and hydrodynamic forces of shear flow. The influence of vibration on structure formation can be well observed during measurement of the yield value of the chocolate suspension under vibration. Comparison with reference data shows how sensitive the structure of the concentrated suspension is to vibration in general. The effects and observations revealed provide a solid basis for further fundamental investigations of structure formation regularities in the flow of any highly concentrated system. The results also show the technological potential for non-conventional treatment of concentrated, multiphase systems.

Influence of starting powder milling on magnetic properties of Mn-Zn ferrite

Directory of Open Access Journals (Sweden)

Miodrag M. Milutinov

2017-06-01

Full Text Available In this paper, the influence of additional sieving and milling of starting industrial Mn-Zn powders on magnetic properties was investigated. The starting powder was milled for 60 minutes, followed by sieving through 325 and 400 meshes. The starting and milled powders were used to fabricate toroid shaped samples sintered at 1200°C for 2 hours. Structural parameters of the fabricated samples were analysed by X-ray diffraction and scanning electron microscopy. Complex permeability, core loss density, and hysteresis were measured using the modified watt-meter method. The complex permeability and hysteresis loop were modelled with a new model proposed in the paper. The core loss density was modelled with the Steinmetz empirical equation. The experimental results and calculations show the significance of the additional milling and sieving process on magnetic properties of Mn-Zn ferrite in the frequency range 0.1-10MHz. These processes increase the relative permeability about 3 times and decrease the core loss 4 times by milling of the starting powder.

Research Update: Mechanical properties of metal-organic frameworks - Influence of structure and chemical bonding

Science.gov (United States)

Li, Wei; Henke, Sebastian; Cheetham, Anthony K.

2014-12-01

Metal-organic frameworks (MOFs), a young family of functional materials, have been attracting considerable attention from the chemistry, materials science, and physics communities. In the light of their potential applications in industry and technology, the fundamental mechanical properties of MOFs, which are of critical importance for manufacturing, processing, and performance, need to be addressed and understood. It has been widely accepted that the framework topology, which describes the overall connectivity pattern of the MOF building units, is of vital importance for the mechanical properties. However, recent advances in the area of MOF mechanics reveal that chemistry plays a major role as well. From the viewpoint of materials science, a deep understanding of the influence of chemical effects on MOF mechanics is not only highly desirable for the development of novel functional materials with targeted mechanical response, but also for a better understanding of important properties such as structural flexibility and framework breathing. The present work discusses the intrinsic connection between chemical effects and the mechanical behavior of MOFs through a number of prototypical examples.

Influence of various irradiation processes on the mechanical properties and polymerisation kinetics of bulk-fill resin based composites.

Science.gov (United States)

Ilie, Nicoleta; Keßler, Andreas; Durner, Jürgen

2013-08-01

To assess the effect of irradiation time and distance of the light tip on the micro-mechanical properties and polymerisation kinetics of two bulk-fill resin-based composites at simulated clinically relevant filling depth. Micro-mechanical properties (Vickers hardness (HV), depth of cure (DOC) and indentation modulus (E)) and polymerisation kinetics (real-time increase of degree of cure (DC)) of two bulk-fill resin-based composites (Tetric EvoCeram(®) Bulk Fill, Ivoclar Vivadent and x-tra base, Voco) were assessed at varying depth (0.1-6mm in 100μm steps for E and HV and 0.1, 2, 4 and 6mm for DC), irradiation time (10, 20 or 40s, Elipar Freelight2) and distances from the light tip (0 and 7mm). Curing unit's irradiance was monitored in 1mm steps at distances up to 10mm away from the light tip on a laboratory-grade spectrometer. Multivariate analysis (α=0.05), Student's t-test and Pearson correlation analysis were considered. The influence of material on the measured mechanical properties was significant (η(2)=0.080 for E and 0.256 for HV), while the parameters irradiation time, distance from the light tip and depth emphasise a stronger influence on Tetric EvoCeram(®) Bulk Fill. The polymerisation kinetics could be described by an exponential sum function, distinguishing between the gel and the glass phase. The above mentioned parameters strongly influenced the start of polymerisation (gel phase), and were of less importance for the glass phase. Both materials enable at least 4mm thick increments to be cured in one step under clinically relevant curing conditions. The susceptibility to variation in irradiance was material dependent, thus properties measured under clinically simulated curing conditions might vary to a different extent from those measured under ideal curing conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Influence of rare-earth ions on fluorogallate glass formation and properties

International Nuclear Information System (INIS)

Zhang Guoyin; Poulain, M.J.

1998-01-01

Various rare earths have been incorporated in a lead fluorogallate glass with the following chemical composition: 30PbF 2 -20GaF 3 -15InF 3 -20CdF 2 -15ZnF 2 (PGICZ). Selected rare earths are La, Ce, Pr, Nd, Gd, Er, Yb and Lu, and the doping level varies between 1 and 10 mol%. The influence of rare earth fluorides on glass forming ability and on physical properties is investigated. At low concentration ( 3 in a modified PGCIZ glass have been cast. Experimental results suggest that rare earths act as modifiers rather than vitrifies in this fluorogallate system. The effect of rare earths on the values of glass transition temperature, refractive index, density and thermal expansion is reported. (orig.)

INFLUENCE OF COCONUT SHELL ADDITION ON PHYSICO-MECHANICAL PROPERTIES OF WOOD PLASTIC COMPOSITES1

Directory of Open Access Journals (Sweden)

Éverton Hillig

2018-04-01

Full Text Available ABSTRACT In this study, composites with three types of thermoplastic matrix and cellulosic material in a proportion of 40% were produced. The three thermoplastic matrices were high density polyethylene (HDPE, polypropylene (PP and low density polyethylene (LDPE, and the cellulosic materials were pure wood flour (Pinus taeda L or a mixture of wood flour and coconut shell flour (Cocus nucifera L in equal ratios. The objective was to evaluate the influence of addition of coconut shell on the physico-mechanical properties (density, strength and rigidity and the distribution of the cellulosic material in the thermoplastic matrix of the manufactured composites. It was found that the composites had a satisfactory distribution of wood flour in thermoplastic matrices, but the addition of coconut shell promoted bubble formation in the resulting pieces and, thus, interfered with the material properties. The use of a coupling agent promoted interfacial adhesion (cellulose - thermoplastic matrix, which was better in high density polyethylene composites, followed by polypropylene and low density polyethylene. In general, the coconut shell addition caused a decrease of all properties compared to composites made with Loblolly Pine. In addition, the interactions between thermoplastic type and cellulosic matrix type have been statistically confirmed, which caused variations in the studied properties

Physico-chemical and mineralogical properties influencing water-stability of aggregates of some Italian surface soils

International Nuclear Information System (INIS)

Mbagwu, J.S.C.; Bazzoffi, P.; Unamba Oparah, I.

1994-06-01

A laboratory study was conducted to determine the relationship between physical, chemical and mineralogical properties of some surface soils (developed in north central Italy) and the stability of their aggregates to water. The index of stability used is the mean-weight diameter of water-stable aggregates (MWD). The ratio of total sand to clay which correlated negatively with MWD (r=-0.638) is the physical property which explained most of the variability in aggregate stability. The chemical properties which correlated best with aggregate stability are FeO (r=0.671), CaO (R=0.635), CaCO 3 (r=0.651) and SiO 2 (r=-0.649). Feldspar, chlorite and calcite are the minerals which influence MWD most, with respective ''r'' values of -0.627, 0.588 and 0.550. The best-fit model developed from soil physical properties explained 59% of the variation in MWD with a standard error of 0.432, that developed from chemical properties explained 97% of the variation in MWD with a standard error of 0.136, whereas the model developed from mineralogical properties explained 78% of the variation in MWD with a standard error of 0.222. Also the closest relationship between measured and model-predicted MWD was obtained with the chemical properties-based model (r=0.985), followed by the mineralogical properties-based model (r=0.884) and then the physical properties-based model (r=0.656). This indicates that the most reliable inference on the stability of these soils in water can be made from a knowledge of the amount and composition of their chemical constituents. (author). 32 refs, 1 fig., 9 tabs

The Influence of the Properties of Embroidery Threads on Buckling of Fabric Inside of the Embroidered Element

Directory of Open Access Journals (Sweden)

Svetlana RADAVIČIENĖ

2012-12-01

Full Text Available In production of garments, embroidery carries out a variety of functions, one of which is the aesthetic appearance of the product improvement. The resulting defects, are seen as a negative indicator of the product quality. The discrepancy of the embroidered element to the digital design in size is a defect, which is influenced by the embroidery threads, embroidery materials properties and process parameters. The fabric sorrounded by the embroidery threads between adjancent needle penetrations inside of the embroidered element is compressed, buckling. The aim of this paper is to investigate the influence of the properties of embroidery threads on buckling of fabric inside of the embroidered element. For investigations specimens were prepared using different fibre composition, density and linear structure of the embroidery threads. Specimens were cut and photo-captured at the beginning, middle and end of the embroidered element.  It was found, that different properties of the embroidery threads affecting on the different behavior of fabric inside of the embroidered element. The results of the investigations showed that the fabric inside of the embroidered element formed larger waves of buckling using the maximum elongation of the feedback exhibiting embroidery thread.DOI: http://dx.doi.org/10.5755/j01.ms.18.4.3100

Influence of groove size and reinforcements addition on mechanical properties and microstructure of friction stir welded joints

Science.gov (United States)

Reddy Baridula, Ravinder; Ibrahim, Abdullah Bin; Yahya, Che Ku Mohammad Faizal Bin Che Ku; Kulkarni, Ratnakar; Varma Ramaraju, Ramgopal

2018-03-01

The butt joints fabricated by friction stir welding were found to have more strength than the joints obtained by conventional joining process. The important outcome of this process is the successful fabrication of surface composites with improved properties. Thus in order to further enhance the strength of the dissimilar alloy joints the reinforcements can be deposited in to the aluminium matrix during the process of friction stir welding. In the present study the multi-walled carbon nanotubes were embedded in to the groove by varying the width during joining of dissimilar alloys AA2024 and AA7075. Four widths were selected with constant depth and optimum process parameters were selected to fabricate the sound welded joints. The results show that the mechanical properties of the fabricated butt joints were influenced by the size of the groove, due to variation in the deposition of reinforcement in the stir zone. The microstructural study and identification of the elements of the welded joints show that the reinforcements deposition is influenced by the size of the groove. It has also been observed that the groove with minimum width is more effective than higher width. The mechanical properties are found to be improved due to the pinning of grain boundaries.

Enhancing sewage sludge dewaterability by bioleaching approach with comparison to other physical and chemical conditioning methods.

Science.gov (United States)

Liu, Fenwu; Zhou, Jun; Wang, Dianzhan; Zhou, Lixiang

2012-01-01

The sewage sludge conditioning process is critical to improve the sludge dewaterability prior to mechanical dewatering. Traditionally, sludge is conditioned by physical or chemical approaches, mostly with the addition of inorganic or organic chemicals. Here we report that bioleaching, an efficient and economical microbial method for the removal of sludge-borne heavy metals, also plays a significant role in enhancing sludge dewaterability. The effects of bioleaching and physical or chemical approaches on sludge dewaterability were compared. The conditioning result of bioleaching by Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans on sludge dewatering was investigated and compared with the effects of hydrothermal (121 degrees C for 2 hr), microwave (1050 W for 50 sec), ultrasonic (250 W for 2 min), and chemical conditioning (24% ferric chloride and 68% calcium oxide; dry basis). The results show that the specific resistance to filtration (SRF) or capillary suction time (CST) of sludge is decreased by 93.1% or 74.1%, respectively, after fresh sludge is conditioned by bioleaching, which is similar to chemical conditioning treatment with ferric chloride and calcium oxide but much more effective than other conditioning approaches including hydrothermal, microwave, and ultrasonic conditioning. Furthermore, after sludge dewatering, bioleached sludge filtrate contains the lowest concentrations of chroma (18 times), COD (542 mg/L), total N (TN, 300 mg/L), NH4(+)-N (208 mg/L), and total P (TP, 2 mg/L) while the hydrothermal process resulted in the highest concentration of chroma (660 times), COD (18,155 mg/L), TN (472 mg/L), NH4(+)-N (381 mg/L), and TP (191 mg/L) among these selected conditioning methods. Moreover, unlike chemical conditioning, sludge bioleaching does not result in a significant reduction of organic matter, TN, and TP in the resulting dewatered sludge cake. Therefore, considering sludge dewaterability and the chemical properties of sludge

Determination of Crosslink Concentration by Mooney-Rivlin Equation for Vulcanized NR/ SBR Blend and its Influence on Mechanical Properties

International Nuclear Information System (INIS)

Azreen Izzati Dzulkifli; Che Mohd Som Said; Han, C.C.

2015-01-01

Crosslink concentration is an important property affecting the major characteristic of cured rubber. The crosslink concentration was determined using Mooney-Rivlin equation due to its simple and reliable method. Cured natural rubber and styrene butadiene rubber blend (NR/SBR) with different crosslink concentrations were obtained with different blend ratios of 100/0, 80/20, 70/30, 60/40, 50/50, 40/60 and 0/100. The crosslink concentrations were determined using Mooney-Rivlin Equation and its influence on International Rubber Hardness Tester (IRHD), tensile strength and rebound resilience of NR/ SBR blend vulcanizates was investigated. The results showed different blend ratios had an influence on the crosslink concentration of the NR/ SBR blend vulcanizates. Obtained data showed that high NR content in NR/ SBR blend increased the crosslink concentration. The highest crosslink concentration recorded was for 100/0 blend ratio which was 0.0498 mol kg"-"1 RH while the lowest was 0.0295 mol kg"-"1 RH for 0/100 blend ratio. The study on the influence of crosslink concentration on IRHD, tensile strength and rebound resilience of NR/ SBR blend vulcanizates showed that the mechanical properties increased linearly with the crosslink concentration. High NR content in NR/ SBR blends resulted in higher crosslink concentration which improved the performance of mechanical properties for NR/ SBR blend. (author)

The influence of ytterbium doping on the optical properties of tellurite glasses

Energy Technology Data Exchange (ETDEWEB)

Jaglarz, Janusz; Burtan, Bozena [Institute of Physics, Cracow University of Technology, ul. Podchorazych 1, 30-084 Cracow (Poland); Reben, Manuela; Wasylak, Jan [Faculty of Materials Science and Ceramics, AGH - University of Science and Technology, al. Mickiewicza 30, 30-059 Cracow (Poland); Cisowski, Jan [Institute of Physics, Cracow University of Technology, ul. Podchorazych 1, 30-084 Cracow (Poland); Centre of Polymer and Carbon Materials, Polish Academy of Sciences, ul. M. Curie-Sklodowskiej 34, 41-819 Zabrze (Poland); Jarzabek, Bozena [Centre of Polymer and Carbon Materials, Polish Academy of Sciences, ul. M. Curie-Sklodowskiej 34, 41-819 Zabrze (Poland)

2011-09-15

The goal of this work was to investigate the influence of rare earth ion Yb{sup 3+} doping on the thermal and optical properties of tellurite glass (TG) of the TeO{sub 2}-ZnO-PbO-La{sub 2}O{sub 3} system. The reflectance, transmittance and ellipsometric measurements have been done. Decreasing of the refractive index of TG with the Yb{sup 3+} ion doping has been concluded. For determination of the refractive index variation in the bulk, the small angle light scatter (SALS) measurements have been carried out. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Systematic Investigation on the Influence of Spray Parameters on the Mechanical Properties of Atmospheric Plasma-Sprayed YSZ Coatings

Science.gov (United States)

Mutter, Markus; Mauer, Georg; Mücke, Robert; Guillon, Olivier; Vaßen, Robert

2018-04-01

In the atmospheric plasma spray (APS) process, micro-sized ceramic powder is injected into a thermal plasma where it is rapidly heated and propelled toward the substrate. The coating formation is characterized by the subsequent impingement of a large number of more or less molten particles forming the so-called splats and eventually the coating. In this study, a systematic investigation on the influence of selected spray parameters on the coating microstructure and the coating properties was conducted. The investigation thereby comprised the coating porosity, the elastic modulus, and the residual stress evolution within the coating. The melting status of the particles at the impingement on the substrate in combination with the substrate surface condition is crucial for the coating formation. Single splats were collected on mirror-polished substrates for selected spray conditions and evaluated by identifying different types of splats (ideal, distorted, weakly bonded, and partially molten) and their relative fractions. In a previous study, these splat types were evaluated in terms of their effect on the above-mentioned coating properties. The particle melting status, which serves as a measure for the particle spreading behavior, was determined by in-flight particle temperature measurements and correlated to the coating properties. It was found that the gun power and the spray distance have a strong effect on the investigated coating properties, whereas the feed rate and the cooling show minor influence.

Motor unit recruitment strategies and muscle properties determine the influence of synaptic noise on force steadiness

Science.gov (United States)

Dideriksen, Jakob L.; Negro, Francesco; Enoka, Roger M.

2012-01-01

Motoneurons receive synaptic inputs from tens of thousands of connections that cause membrane potential to fluctuate continuously (synaptic noise), which introduces variability in discharge times of action potentials. We hypothesized that the influence of synaptic noise on force steadiness during voluntary contractions is limited to low muscle forces. The hypothesis was examined with an analytical description of transduction of motor unit spike trains into muscle force, a computational model of motor unit recruitment and rate coding, and experimental analysis of interspike interval variability during steady contractions with the abductor digiti minimi muscle. Simulations varied contraction force, level of synaptic noise, size of motor unit population, recruitment range, twitch contraction times, and level of motor unit short-term synchronization. Consistent with the analytical derivations, simulations and experimental data showed that force variability at target forces above a threshold was primarily due to low-frequency oscillations in neural drive, whereas the influence of synaptic noise was almost completely attenuated by two low-pass filters, one related to convolution of motoneuron spike trains with motor unit twitches (temporal summation) and the other attributable to summation of single motor unit forces (spatial summation). The threshold force above which synaptic noise ceased to influence force steadiness depended on recruitment range, size of motor unit population, and muscle contractile properties. This threshold was low (motor unit recruitment and muscle properties of a typical muscle are tuned to limit the influence of synaptic noise on force steadiness to low forces and that the inability to produce a constant force during stronger contractions is mainly attributable to the common low-frequency oscillations in motoneuron discharge rates. PMID:22423000

Influence of the mechanical properties of resilient denture liners on the retention of overdenture attachments.

Science.gov (United States)

Kubo, Keitaro; Koike, Takashi; Ueda, Takayuki; Sakurai, Kaoru

2018-03-15

Information is lacking about the selection criteria for silicone resilient denture liners applied as a matrix material for attachments on overdentures. The purpose of this in vitro study was to investigate the mechanical properties of silicone resilient denture liners and their influence on the initial retention force of overdenture attachments and the reduction in retention force over time. Nine types of silicone resilient denture liner were injected and fixed to the matrix section of an experimental denture base. They were then fitted to an epoxy resin model that simulated the residual ridge with a patrix ball attachment (n=10). The retention force of the denture was measured with a digital force gauge, and the maximum force of traction (N) was regarded as the initial retention force. The retention force reduction (N) after repeated insertion and removal (n=5) was calculated by subtracting the retention force after 3348 cycles (3-year simulated insertion and removal) from the initial retention force. The intaglio of the matrix was observed with a scanning electron microscope (SEM) before and after the 3348 cycles. Four mechanical properties (hardness, strain-in-compression, tensile strength, and arithmetic mean roughness) of the resilient denture liners were measured. One-way ANOVA of the initial retention force of each lining material was performed, followed by the Scheffe test (α=.05). Pearson correlation analysis was used (α=.05) to analyze correlations of the initial retention force with the retention force reduction after insertion and removal and the mechanical properties of each material. Multiple regression analysis with the stepwise method extracted the initial retention force and the retention force reduction as dependent variables, and the resilient denture liner mechanical properties as explanatory variables (α=.05). The initial retention force of the resilient denture liners was 1.3 to 5.4 N. Multiple comparisons showed significant differences in

The influence of the addition of polymers on the physico-chemical properties of bentonite suspensions

Directory of Open Access Journals (Sweden)

Stojiljkovic S.

2014-01-01

Full Text Available Bentonite clays have many applications in industries ranging from construction to cosmetics. Addition of polymers can profoundly influence the properties of bentonite suspensions and we now describe the influence of a range of different polymers. Whereas polyvinyl pyrolidone and soy isolate only slightly influenced the pH and the electrical conductivity of bentonite polymers in suspension, Carbopol solution caused decreases in both pH and electrical conductivity. As expected, strong electrolytes like sodium chloride caused big changes in the electrical conductivity of the suspensions. When the temperature of the bentonite suspensions was increased, the pH was almost unchanged, but the electrical conductivity increased. Bentonite treated with polymer suspensions can be used in purifying polluted water; for example, our results suggest that high pH caused by phosphorous salts can be addressed using bentonite modified with Carbopol. [Projekat Ministarstva nauke Republike Srbije: Stanisa Stojiljkovic, Vojkan Miljkovic, Goran Nikolic, Ivana Savic and Ivan Savic, TR 34020, Danijela Kostic 172047 and Biljana Arsic 174007

Influence of Ni/Co molar ratio on electromagnetic properties and microwave absorption performances for Ni/Co paraffin composites

Energy Technology Data Exchange (ETDEWEB)

Yan, S.J., E-mail: shaojiuyan@126.com [Department of Structural Steel, Functional Materials and Heat Treatment Processing, AVIC Beijing Institute of Aeronautical Materials, Beijing 100095 (China); Aviation Key Laboratory of Science and Technology on Stealth Materials, Beijing 100095 (China); Dai, S.L. [The Office of AVIC Beijing Institute of Aeronautical Materials, Beijing 100095 (China); Ding, H.Y.; Wang, Z.Y. [Aviation Key Laboratory of Science and Technology on Stealth Materials, Beijing 100095 (China); Liu, D.B [Department of Structural Steel, Functional Materials and Heat Treatment Processing, AVIC Beijing Institute of Aeronautical Materials, Beijing 100095 (China)

2014-05-01

Ni and Co metallic microparticles with submicron size were synthesized with a simple wet chemical reduction method at a relatively low temperature. Then their morphologies and structures were characterized by SEM and XRD. Ni metallic microparticles have spherical-shape morphology with fcc crystalline structure, however, Co has a distinct leaf-like morphology with the fcc and hcp mixed phases crystalline structures. For the characterization of their electromagnetic properties, paraffin matrix composites containing different molar ratio Ni and Co mixture powder as fillers were prepared. It was found that both the electromagnetic properties and electromagnetic microwave absorption performances of absorber layer were remarkably influenced by Ni/Co molar ratio. The electromagnetic microwave absorption performances were significantly improved by blending Ni and Co metallic microparticles into paraffin matrix with changing Ni/Co molar ratio, and enhanced mechanism were discussed. - Highlights: • Ni and Co microparticles were synthesized by a wet chemical reduction method. • EM properties of absorber were remarkably influenced by Ni/Co molar ratio. • EMA performances can be adjusted by artificially changing Co/Ni molar ratio. • Enhanced EMA performances result from multiple EM attenuation mechanisms.

Diphenylphosphino Styrene-Containing Homopolymers: Influence of Alkylation and Mobile Anions on Physical Properties.

Science.gov (United States)

Jangu, Chainika; Schultz, Alison R; Wall, Candace E; Esker, Alan R; Long, Timothy E

2016-07-01

Conventional free radical polymerization and post-alkylation of 4-diphenylphosphino styrene (DPPS) generate a new class of high-molecular-weight phosphonium-containing homopolymers with tunable thermal, viscoelastic, and wetting properties. Post-alkylation and subsequent anion exchange provide an effective method for tuning Tg values and thermal stability as a function of alkyl chain length and counteranion selection (X(-) , BF4 (-) , TfO(-) , and Tf2 N(-) ). Rheological characterization facilitates the generation of time-temperature-superposition (TTS) pseudomaster curves and subsequent analysis of frequency sweeps at various temperatures reveals two relaxation modes corresponding to long-range segmental motion and the onset of viscous flow. Contact angle measurements reveal the influence of counteranion selection on wetting properties, revealing increased contact angles for homopolymers containing nucleophilic counteranions. These investigations provide fundamental insight into phosphonium-containing polymers, aiming to guide future research and applications involving electro-active polymeric devices. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of dielectric barrier discharge treatment on mechanical and dyeing properties of wool

Science.gov (United States)

Rahul, NAVIK; Sameera, SHAFI; Md Miskatul, ALAM; Md Amjad, FAROOQ; Lina, LIN; Yingjie, CAI

2018-06-01

Physical and chemical properties of wool surface significantly affect the absorbency, rate of dye bath exhaustion and fixation of the industrial dyes. Hence, surface modification is a necessary operation prior to coloration process in wool wet processing industries. Plasma treatment is an effective alternative for physiochemical modification of wool surface. However, optimum processing parameters to get the expected modification are still under investigation, hence this technology is still under development in the wool wet processing industries. Therefore, in this paper, treatment parameters with the help of simple dielectric barrier discharge plasma reactor and air as a plasma gas, which could be a promising combination for treatment of wool substrate at industrial scale were schematically studied, and their influence on the water absorbency, mechanical, and dyeing properties of twill woven wool fabric samples are reported. It is expected that the results will assist to the wool coloration industries to improve the dyeing processes.

The Topological Properties of Stimuli Influence Fear Generalization and Extinction in Humans.

Science.gov (United States)

Xu, Liang; Su, Hongyu; Xie, Xiaoyuan; Yan, Pei; Li, Junjiao; Zheng, Xifu

2018-01-01

Fear generalization is an etiologically significant indicator of anxiety disorders, and understanding how to inhibit it is important in their treatment. Prior studies have found that reducing fear generalization using a generalization stimulus (GS) is ineffective in removing a conditioned fear that incorporates local features, and that topological properties appear to play a comparatively more significant role in the processes of perception and categorization. Our study utilized a conditioned-fear generalization design to examine whether the topological properties of stimuli influence the generalization and return of fear. Fear was indexed using online expectancy ratings and skin conductance responses (SCRs). The study's 52 participants were divided into three groups: Group 1, conditioned danger cue (CS+) extinction; Group 2, extinction of one GS; Group 3, extinction of three GSs. We found that the three groups acquired conditioned fear at the same level. In the generalization and extinction phase, fear was transferred to the GS with the same topological properties as CS+, and gradual decreases in both shock expectancy and SCRs over non-reinforced extinction trials were observed. In the test phase, participants' online expectancy ratings indicated that fear did not return in Group 1, but did return in Groups 2 and 3. All three groups demonstrated successful GS fear extinction, but only Group 1 did not show a return of fear for CS+. Regarding SCRs results, none of the groups demonstrated a return of fear, suggesting that utilization of topological properties successfully reduced the return of conditioned fear. Our results indicate that, in clinical settings, using GS with topological equivalence to CS+ might offer a potential method with which to extinct conditioned fear.

The Topological Properties of Stimuli Influence Fear Generalization and Extinction in Humans

Directory of Open Access Journals (Sweden)

Liang Xu

2018-03-01

Full Text Available Fear generalization is an etiologically significant indicator of anxiety disorders, and understanding how to inhibit it is important in their treatment. Prior studies have found that reducing fear generalization using a generalization stimulus (GS is ineffective in removing a conditioned fear that incorporates local features, and that topological properties appear to play a comparatively more significant role in the processes of perception and categorization. Our study utilized a conditioned-fear generalization design to examine whether the topological properties of stimuli influence the generalization and return of fear. Fear was indexed using online expectancy ratings and skin conductance responses (SCRs. The study’s 52 participants were divided into three groups: Group 1, conditioned danger cue (CS+ extinction; Group 2, extinction of one GS; Group 3, extinction of three GSs. We found that the three groups acquired conditioned fear at the same level. In the generalization and extinction phase, fear was transferred to the GS with the same topological properties as CS+, and gradual decreases in both shock expectancy and SCRs over non-reinforced extinction trials were observed. In the test phase, participants’ online expectancy ratings indicated that fear did not return in Group 1, but did return in Groups 2 and 3. All three groups demonstrated successful GS fear extinction, but only Group 1 did not show a return of fear for CS+. Regarding SCRs results, none of the groups demonstrated a return of fear, suggesting that utilization of topological properties successfully reduced the return of conditioned fear. Our results indicate that, in clinical settings, using GS with topological equivalence to CS+ might offer a potential method with which to extinct conditioned fear.

The influence of prior ageing on microstructure, tensile properties and hot hardness of alloy 800HT

International Nuclear Information System (INIS)

El-Magd, E.

1996-01-01

For high temperature applications especially in the construction of equipment, carbide strengthened steels are widely used because of their good mechanical properties and relatively low cost. These materials undergo microstructural changes under such service conditions which contribute greatly to the strength properties and thus play an important role in equipment design considerations. The influence of a prior thermal ageing on the tensile strength values and the hot hardness of the austenitic iron base alloy, Alloy 800HT, is examined in this work. It was therefore necessary to carry out tensile and hot hardness tests with the solution treated and overaged material at ranges between room temperature and 900 . The microstructural changes are investigated using lightmicroscopy, SEM and TEM. The changes of the material properties with thermal pretreatment conditions is studied and discussed in the context of the determined microstructural development. (orig.) [de

Influence of multiwall carbon nanotube functionality and loading on mechanical properties of PMMA/MWCNT bone cements.

Science.gov (United States)

Ormsby, Ross; McNally, Tony; Mitchell, Christina; Dunne, Nicholas

2010-08-01

Poly (methyl methacrylate) (PMMA) bone cement-multi walled carbon nanotube (MWCNT) nanocomposites with weight loadings ranging from 0.1 to 1.0 wt% were prepared. The MWCNTs investigated were unfunctionalised, carboxyl and amine functionalised MWCNTs. Mechanical properties of the resultant nanocomposite cements were characterised as per international standards for acrylic resin cements. These mechanical properties were influenced by the type and wt% loading of MWCNT used. The morphology and degree of dispersion of the MWCNTs in the PMMA matrix at different length scales were examined using field emission scanning electron microscopy. Improvements in mechanical properties were attributed to the MWCNTs arresting/retarding crack propagation through the cement by providing a bridging effect and hindering crack propagation. MWCNTs agglomerations were evident within the cement microstructure, the degree of these agglomerations was dependent on the weight fraction and functionality of MWCNTs incorporated into the cement.

Influence of Mo impurity on the spectroscopic and scintillation properties of PbWO4 crystals

International Nuclear Information System (INIS)

Boehm, M.; Hofstaetter, A.; Luh, M.; Meyer, B.K.; Scharmann, A.; Drobychev, G.Yu.; Grenoble-1 Univ., 74 - Annecy; Peigneux, J.P.

1997-12-01

The influence of molybdenum doping on the spectroscopic and scintillation properties of lead tungstate crystals has been investigated. From the results the slow scintillation component as well as the afterglow are found to be due to the Mo impurity. In addition the blue luminescence from excited (WO 4 ) 2- -complex seems to be increasingly suppressed as the doping concentration goes on. Possible mechanisms for the effects have been discussed. (author)

Low cloud properties influenced by cosmic rays

DEFF Research Database (Denmark)

Marsh, Nigel; Svensmark, Henrik

2000-01-01

The influence of solar variability on climate is currently uncertain. Recent observations have indicated a possible mechanism via the influence of solar modulated cosmic rays on global cloud cover. Surprisingly the influence of solar variability is strongest in low clouds (less than or equal to3 km......), which points to a microphysical mechanism involving aerosol formation that is enhanced by ionization due to cosmic rays. If confirmed it suggests that the average state of the heliosphere is important for climate on Earth....

Influence of Sintering Temperature on the Microstructure and Mechanical Properties of In Situ Reinforced Titanium Composites by Inductive Hot Pressing

Directory of Open Access Journals (Sweden)

Cristina Arévalo

2016-11-01

Full Text Available This research is focused on the influence of processing temperature on titanium matrix composites reinforced through Ti, Al, and B4C reactions. In order to investigate the effect of Ti-Al based intermetallic compounds on the properties of the composites, aluminum powder was incorporated into the starting materials. In this way, in situ TixAly were expected to form as well as TiB and TiC. The specimens were fabricated by the powder metallurgy technique known as inductive hot pressing (iHP, using a temperature range between 900 °C and 1400 °C, at 40 MPa for 5 min. Raising the inductive hot pressing temperature may affect the microstructure and properties of the composites. Consequently, the variations of the reinforcing phases were investigated. X-ray diffraction, microstructural analysis, and mechanical properties (Young’s modulus and hardness of the specimens were carried out to evaluate and determine the significant influence of the processing temperature on the behavior of the composites.

Influence of solubilizer PEG-40 hydrogenated castor oil on carbopol gels’ structural-mechanical properties

Directory of Open Access Journals (Sweden)

Ye. V. Gladukh

2017-12-01

Full Text Available Rheological properties affect all stages of the drug development – from development to production, the characteristics of the final products and stability. A lot of substances have complex rheological properties; their viscosity and elasticity can vary depending on conditions acting from the outside, such as stress, deformation, time factor and temperature. Concentration, stability and composition also significantly affect the rheological properties of drugs. One of the current trends in modern pharmacy is the development of drugs in the form of gels. The rheological properties of gels are significantly influenced by surface-active substances, stabilizers, solubilizers, stabilizing their structure. A special group of stabilizers are hydrogenated vegetable oils and their compounds with polymers, which have the ability to structure formation in interphase layers and in the volume of phases. For this purpose, PEG-40 hydrogenated castor oil is widely used. The aim of this work is to study the effect of hydrogenated castor oil, used as an emulsifier, solubilizer, viscosity modifier and solvent in the technology of semisolid dosage forms, on the structural and mechanical properties of carbopol gels. Materials and methods. 1% gel carbopol with additives PEG-40 hydrogenated castor oil in the concentration range from 1 to 5 % was investigated as experimental samples of the gel base. A 10 % propylene glycol additive was used as humectant and plasticizer. Structural and mechanical studies were carried out using a rotational viscometer «RheolabQC», Anton Paar (Austria with coaxial cylinders CCC27/SS. The graphs of the gels were automatically plotted using the computer program. Results. Analysis of the rheological parameters of the carbopol with PEG-40 hydrogenated castor oil gel base shows that the solubilizer has an active influence on the structural and mechanical properties of the base. Addition of PEG-40 GMM to the carbopol gel increases the yield

Compatibilizing agents influence on mechanical properties of PP/clay nanocomposites

DEFF Research Database (Denmark)

Sanporean, Catalina-Gabriela; Donescu, Dan; Vuluga, Zina

2013-01-01

S-a investigat din punct de vedere mecanic influenţa concentraţiei de argilă şi a utilizării unui sistem cu doi agenţi de compatibilizare. Argila Cloisite –Na a fost modificată organic cu o polietermonoamină, iar, ca agent de compatibilizare secund, s-a adăugat polipropilena maleinizată (MA-PP) s...... in mechanical properties, especially in tensile strength, creep strain and cyclic test, while those with MA-SEBS presented an improvement in neck propagation, as well as an increase in ductility....... la testare ciclică, în timp ce nanocompozitele cu MASEBS au prezentat o îmbunătăţire a curgerii superioare şi o creştere a ductilităţii. The influence of Clay concentration and of two compatibilizers system use was investigated from mechanical point of view. Cloisite-Na Clay was organically modified...

Influence of surface roughness on the friction property of textured surface

Directory of Open Access Journals (Sweden)

Yuankai Zhou

2015-02-01

Full Text Available In contrast with dimple textures, surface roughness is a texture at the micro-scale, essentially which will influence the load-bearing capacity of lubricant film. The numerical simulation was carried out to investigate the influence of surface roughness on friction property of textured surface. The lubricant film pressure was obtained using the method of computational fluid dynamics according to geometric model of round dimple, and the renormalization-group k–ε turbulent model was adopted in the computation. The numerical simulation results suggest that there is an optimum dimensionless surface roughness, and near this value, the maximum load-bearing capacity can be achieved. The load-bearing capacity is determined by the surface texture, the surface roughness, and the interaction between them. To get information of friction coefficient, the experiments were conducted. This experiment was used to evaluate the simulation. The experimental results show that for the frequency of 4 and 6 Hz, friction coefficient decreases at first and then increases with decreasing surface roughness, which indicates that there exists the optimum region of surface roughness leading to the best friction reduction effect, and it becomes larger when area fractions increase from 2% to 10%. The experimental results agree well with the simulation results.

Loire and Gironde turbid plumes: Characterization and influence on thermohaline properties

Science.gov (United States)

Costoya, X.; Fernández-Nóvoa, D.; deCastro, M.; Gómez-Gesteira, M.

2017-12-01

Knowledge and predictability of turbid river plumes is of great importance because they modulate the properties of the seawater adjacent to river mouths. The Loire and Gironde Rivers form the most important plumes in the Bay of Biscay, as they provide > 75% of total runoff. The development of the turbid plume under the influence of its main drivers was analyzed using Moderate Resolution Imaging Spectroradiometer satellite data from the period 2003-2015. River discharge was found to be the main driver, followed by wind, which also had an important effect in modulating the turbid plume during periods of high river discharge. Seaward and upwelling favorable winds enhanced the dispersion of plumes on seawater, whereas landward and downwelling favorable winds limited mixing with the adjacent ocean water. The maximum extension of the turbid plume was reached under landward winds. In addition, the spatio-temporal evolution of the East Atlantic pattern and the North Atlantic Oscillation was observed to affect the dynamics of plumes: positive values of both indices favored a greater extension of the plume. Thermohaline properties differed inside and outside the area affected by both rivers. In particular, these rivers maintain winter stratification inside the turbid plume, which results in a different warming ratio when compared with the adjacent ocean.

Influence of fluid-property variation on turbulent convective heat transfer in vertical annular CHANNEL FLOWS

International Nuclear Information System (INIS)

Joong Hun Bae; Jung Yul Yoo; Haecheon Choi

2005-01-01

Full text of publication follows: The influence of variable fluid property on turbulent convective heat transfer is investigated using direct numerical simulations. We consider thermally-developing flows of air and supercritical-pressure CO 2 in a vertical annular channel where the inner wall is heated with a constant heat flux and the outer wall is insulated. Turbulence statistics show that the heat and momentum transport characteristics of variable-property flows are significantly different from those of constant-property flows. The difference is mainly caused by the spatial and temporal variations of fluid density. The non-uniform density distribution causes fluid particles to be accelerated either by expansion or buoyancy force, while the temporal density fluctuations change the heat and momentum transfer via transport of turbulent mass flux, ρ'u' i . Both effects of the spatial and temporal variations of density are shown to be important in the analysis of turbulent convective heat transfer for supercritical-pressure fluids. For variable-property heated air flows, however, the effect of temporal density fluctuations can be neglected at low Mach number, which is in good accordance with the Morkovin's hypothesis. (authors)

Influence of the virtual photon field on the squeezing properties of an atom laser

International Nuclear Information System (INIS)

Jian-Gang, Zhao; Chang-Yong, Sun; Ling-Hua, Wen; Bao-Long, Liang

2009-01-01

This paper investigates the squeezing properties of an atom laser without rotating-wave approximation in the system of a binomial states field interacting with a two-level atomic Bose–Einstein condensate. It discusses the influences of atomic eigenfrequency, the interaction intensity between the optical field and atoms, parameter of the binomial states field and virtual photon field on the squeezing properties. The results show that two quadrature components of an atom laser can be squeezed periodically. The duration and the degree of squeezing an atom laser have something to do with the atomic eigenfrequency and the parameter of the binomial states field, respectively. The collapse and revival frequency of atom laser fluctuation depends on the interaction intensity between the optical field and atoms. The effect of the virtual photon field deepens the depth of squeezing an atom laser

Unified Modeling of Filtration and Expression of Biological Sludge

DEFF Research Database (Denmark)

Sørensen, Peter Borgen

Dewatering is a costly operation in both industry, e.g . when dewatering drilling mud, harbor sludge or biomass, and at municipal wastewater treatment plants when dewatering biological sludges. In practice, design and operation of dewatering equipment are mostly based on empirical knowledge, and ......, and normally results are not satisfactory, e.g. in terms of cake solids or capacity of equipment. Thus, there is a need for theoretical and technical developments to improve dewatering performance, based on better scientific knowledge and well defined principles and rules....

Influence of Nickel Addition on Properties of Secondary AlSi7Mg0.3 Alloy

Directory of Open Access Journals (Sweden)

Richtárech L.

2015-06-01

Full Text Available This paper deals with influence on segregation of iron based phases on the secondary alloy AlSi7Mg0.3 microstructure by nickel. Iron is the most common and harmful impurity in aluminum casting alloys and has long been associated with an increase of casting defects. In generally, iron is associated with the formation of Fe-rich intermetallic phases. It is impossible to remove iron from melt by standard operations. Some elements eliminates iron by changing iron intermetallic phase morphology, decreasing its extent and by improving alloy properties. Realization of experiments and results of analysis show new view on solubility of iron based phases during melt preparation with higher iron content and influence of nickel as iron corrector of iron based phases.

Influence of fillers on mechanical properties of filled rubbers during ageing by irradiation

International Nuclear Information System (INIS)

Planes, Emilie

2008-01-01

The understanding of the evolution of mechanical properties and the prediction of the lifetime of material environment is a recurring problem. This question is very important to develop polymer formulations used for electrical cables in nuclear power plants. Thus it is important to know the evolution of materials when they are submitted to usual conditions in nuclear power plants. There are in literature some studies concerning the ageing by gamma irradiation of unfilled elastomer but the addition of fillers in the material can have consequences on the evolution of the mechanical properties during irradiation. Thus this work concerns the study of the ageing by gamma irradiation of filled rubbers and the identification of the role of fillers in the degradation mechanisms. The studied matrix, which commonly used for the type of application is EPDM. The fillers are: nano-scopic silica and aluminium trihydrate. Their surfaces have been treated in order to understand the role of filler-matrix interfaces during ageing. To evaluate the influence of fillers on the degradation mechanisms and on the evolution of the mechanical properties, the evolution during ageing of these materials filled or not has been studied for an ageing by irradiation: they have been physico-chemically, micro-structurally and mechanically characterized at various levels of ageing [fr

Influence of recycled aggregate quality and proportioning criteria on recycled concrete properties.

Science.gov (United States)

López-Gayarre, F; Serna, P; Domingo-Cabo, A; Serrano-López, M A; López-Colina, C

2009-12-01

This paper presents the results of experimental research using concrete produced by substituting part of the natural coarse aggregates with recycled aggregates from concrete demolition. The influence of the quality of the recycled aggregate (amount of declassified and source of aggregate), the percentage of replacement on the targeted quality of the concrete to be produced (strength and workability) has been evaluated. The granular structure of concrete and replacement criteria were analyzed in this study, factors which have not been analyzed in other studies. The following properties of recycled concretes were analyzed: density, absorption, compressive strength, elastic modulus, amount of occluded air, penetration of water under pressure and splitting tensile strength. A simplified test program was designed to control the costs of the testing while still producing sufficient data to develop reliable conclusions in order to make the number of tests viable whilst guaranteeing the reliability of the conclusions. Several factors were analyzed including the type of aggregate, the percentage of replacement, the type of sieve curve, the declassified content, the strength of concrete and workability of concrete and the replacement criteria. The type of aggregate and the percentage of replacement were the only factors that showed a clear influence on most of the properties. Compressive strength is clearly affected by the quality of recycled aggregates. If the water-cement ratio is kept constant and the loss of workability due to the effect of using recycled aggregate is compensated for with additives, the percentage of replacement of the recycled aggregate will not affect the compressive strength. The elastic modulus is affected by the percentage of replacement. If the percentage of replacement does not exceed 50%, the elastic modulus will only change slightly.

On the influence of Ti-Al intermetallic coating architecture on mechanical properties and wear resistance of end mills

Science.gov (United States)

Vardanyan, E. L.; Budilov, V. V.; Ramazanov, K. N.; Ataullin, Z. R.

2017-07-01

Thin-film wear-resistant coatings are widely used to increase life and efficiency of metal cutting tools. This paper shows the results of a study on the influence of architecture (number, sequence and thickness of layers) of wear-resistant coatings on physical, mechanical and operational properties of end mills. Coatings consisting of alternating Ti-Al/Ti-Al-N layers of equal thickness demonstrated the best physical and mechanical properties. Durability of coated tools when processing materials from chromium-vanadium steel increased twice as compared to uncoated tools.

Influence of temperature of the short-period heat treatment on mechanical properties of the NiTi alloy

Directory of Open Access Journals (Sweden)

Jaroslav Čapek

2014-01-01

Full Text Available The equiatomic alloy of nickel and titanium, known as nitinol, possesses unique properties such as superelasticity, pseudoplasticity, shape memory, while maintaining good corrosion resistance and sufficient biocompatibility. Therefore it is used for production of various devices including surgery implants. Heat treatment of nickel-rich NiTi alloys can result in precipitation of nickel-rich phases, which strongly influence tensile and fatigue behaviour of the material.In this work we have studied influence of short-period heat treatment on tensile behaviour and fatigue life of the NiTi (50.9 at. % Ni wire intended for fabrication of surgery stents.

Influence of the Substrate Properties on the Offset Printing ink Colour Matching

Directory of Open Access Journals (Sweden)

Anne Blayo

2003-07-01

Full Text Available The printing industry has been using computerised ink colour matching for a long time. The problem of ink formulation is to match a given standard colour with only three or four inks from a basis of about twelve inks.This is generally achieved by calculations based on the well-known Kubelka-Munk turbid media theory, which gives excellent results in many industrial situations. However, some hypotheses are necessary to apply the Kubelka-Munk model and corrections to the measured reflectance are often required (Saunderson’s correction coefficients, for example.One limitation in the resolution of this method of formulation may arise from the fact that the characterisation of the basic inks is made on one standard substrate, which may differ a lot from the real printing substrate.The aim of this work is precisely to study the contribution of the substrate to the colour matching procedure. The properties of the substrate which intervene in the process are physical properties (thickness, absorbency… and optical properties (brightness and gloss. Five different papers were chosen to make the characterisations of the basic offset inks. The reflectance measurements were performed with spectrophotometer X-Rite with the D/0° geometry, specular excluded or included, coupled with a coloured matching software (X-Rite Inkmaster. A special emphasis was put on the influence on the calculation of the ink film thickness, estimated for the different substrates, and on the choice of the correction coefficients for the Kubelka-Munk theory.

The influence of {gamma}-irradiation on electrophysical properties of spinel-based oxide ceramics

Energy Technology Data Exchange (ETDEWEB)

Kovalskiy, A.P.; Shpotyuk, O.I. E-mail: karat@ipm.lviv.ua; Hadzaman, I.V.; Mrooz, O.Ya.; Vakiv, M.M

2000-05-02

The influence of {sup 60}Co {gamma}-irradiation with 1.25 MeV average energy and 1 MGy absorbed dose on electrophysical properties of Cu-, Ni-, Co- and Mn-based spinel ceramic materials in the Cu{sub x}Ni{sub 1-x-y}Co{sub 2y}Mn{sub 2-y}O{sub 4} (0,1{<=}x{<=}0,8;0,1{<=}y{<=}0,9-x) system is investigated. The {gamma}-induced increasing of the electrical resistance is observed for the investigated samples of various compositions. It is supposed that these changes are explained by cationic redistribution in the spinel sublattices of the ceramics.

The influence of γ-irradiation on electrophysical properties of spinel-based oxide ceramics

International Nuclear Information System (INIS)

Kovalskiy, A.P.; Shpotyuk, O.I.; Hadzaman, I.V.; Mrooz, O.Ya.; Vakiv, M.M.

2000-01-01

The influence of 60 Co γ-irradiation with 1.25 MeV average energy and 1 MGy absorbed dose on electrophysical properties of Cu-, Ni-, Co- and Mn-based spinel ceramic materials in the Cu x Ni 1-x-y Co 2y Mn 2-y O 4 (0,1≤x≤0,8;0,1≤y≤0,9-x) system is investigated. The γ-induced increasing of the electrical resistance is observed for the investigated samples of various compositions. It is supposed that these changes are explained by cationic redistribution in the spinel sublattices of the ceramics

Photoreactivity of biologically active compounds. XVII. Influence of solvent interactions on spectroscopic properties and photostability of primaquine.

Science.gov (United States)

Kristensen, S

2005-06-01

The influence of solvent interactions on absorption properties, fluorescence properties (emission spectra and quantum yields) and relative photochemical degradation rates of primaquine has been investigated, in order to evaluate photochemical reaction mechanisms and chemical properties of the compound. The first absorption band (n - pi*) of primaquine is only slightly dependent on properties of the solvent, which can be ascribed to a strong, intramolecular hydrogen bond between the quinoline N and amine group in the ground state (S0). Amphiprotic solvents with predominant acidic properties (water and methanol) will to some extent stabilize the molecule and initiate hypsochromic shifts of the absorption band by protic interactions, while the other solvents (amphiprotic, basic and neutral) influence the absorption spectrum by general solvent effects only. The excited singlet (S1*) state of primaquine interacts more efficiently with the surrounding solvents than the S0 state, as evaluated by the Stokes shifts. The pKa value of the quinoline N is likely to increase in the S1* state, which is important for the observed protic interactions with amphiprotic solvents of predominant acidity. Specific solvent effects are highly important for the efficiency of the fluorescence (fluorescence quantum yields; phi f). The fluorescence is quenched by amphiprotic solvents, likely due to a rupture of the intramolecular bond and protonation of the quinolone N, and enhanced by polar, non-protic (basic) solvents, probably by stabilization of the delta intramolecular hydrogen bond. The observed photochemical degradation rates of primaquine in amphiprotic media are positively correlated with phi f, indicating that the photochemical degradation of primaquine is dependent on intramolecular hydrogen bonding and non protonated lone-pair electrons at the quinoline N. The intramolecular ring-formation with a subsequent increased lipophilic character and (lack of) interactions with the

Influence of laser radiation on structure and properties of steels and alloys

International Nuclear Information System (INIS)

Tarasova, T; Popova, E

2013-01-01

In present study, and laser alloying of different steels and laser cladding of Ti and SiC powders mixtures was carried out, and microstructure, as well as microhardness profile and wear properties were examined. Research of the influence of lasers alloying modes on the elastic and plastic characteristics of the surface was conducted. As a result of chemical reactions in the cladded layer, a new phase (TiC) was synthesized during cladding process. The results showed that, in the clad layer, TiC was solidified to form dendrites in the clad zone. Produced coatings have high microhardness values in the upper and middle clad areas, about two time higher than clad matrix microhardness.

The influence of interfacial properties on the two-phase liquid flow of organic contaminants in groundwater

International Nuclear Information System (INIS)

Demond, A.H.; Desai, F.N.; Hayes, K.F.

1992-01-01

DOE's waste sites are contaminated with a variety of organic liquids. Because of their low solubility in water, organic liquids such as these will persist as separate liquid phases and be transported as such in the subsurface. Thus, an improved understanding of the factors influencing the movement of a separate organic liquid phase in the subsurface is important to DOE's efforts to control groundwater contamination. Wettability is sometimes cited as the most important factor influencing two-phase flow in porous media. The wetting phase migrates preferentially through the smaller pores, whereas the nonwetting phase is concentrated in the larger pores. Typically, aquifers are thought of as strongly water-wet, implying that the organic liquid preferentially occupies the larger pores. But in fact, that state depends on the properties of the three interfaces of the system: between the organic liquid and water, water and the solid, and the organic liquid and the solid. Characteristics of the system which affect the interfacial properties also impact the wettability, such as the nature of the aquifer solids' surfaces, the composition of the goundwater and the properties of the organic contaminant. The alteration of wettability at DOE waste sites may be dominated by the presence of co-contaminants such as organic acids and bases which behave as surface-active agents or surfactants. Because of their physicochemical nature, surfactants will sorb preferentially at the interfaces of the system, thereby impacting the wettability and the distribution of the liquids in the porous medium. The over-all objective of this research was to determine how changes in interfacial properties affect two-phase flow. Specifically, the objective was to examine the effect of surfactant sorption on capillary pressure relationships by correlating measurements of sorption, zeta potential, interfacial tension and contact angle, with changes in the capillary pressure-saturation relationships

Preparation and characterization of nano fluids: Influence of variables on its stability, agglomeration state and physical properties

International Nuclear Information System (INIS)

Mondragon, R.; Julia, J. E.; Barba, A.; Jarque, J. C.

2014-01-01

In recent years it has spread the use of suspensions containing nano metre sized particles, known as nano fluids, in many applications owing the good properties having nanocrystalline materials. One of the main advantages of using nano fluids is its high stability, which causes the particles do not settle over long periods of time. This stability depends on the preparation conditions such as pH, the presence of electrolytes or the solids content. Moreover, there are a number of physical properties which are influenced and altered by agglomeration of the particles. This article will analyze all the variables that affect agglomeration of the particles, nano fluids stability and properties from which it can obtain information on the state of suspension. It then lays out the different methods of dispersion of nanoparticles and their effectiveness. (Author)

Influence of packing density and surface roughness of vertically-aligned carbon nanotubes on adhesive properties of gecko-inspired mimetics.

Science.gov (United States)

Chen, Bingan; Zhong, Guofang; Oppenheimer, Pola Goldberg; Zhang, Can; Tornatzky, Hans; Esconjauregui, Santiago; Hofmann, Stephan; Robertson, John

2015-02-18

We have systematically studied the macroscopic adhesive properties of vertically aligned nanotube arrays with various packing density and roughness. Using a tensile setup in shear and normal adhesion, we find that there exists a maximum packing density for nanotube arrays to have adhesive properties. Too highly packed tubes do not offer intertube space for tube bending and side-wall contact to surfaces, thus exhibiting no adhesive properties. Likewise, we also show that the surface roughness of the arrays strongly influences the adhesion properties and the reusability of the tubes. Increasing the surface roughness of the array strengthens the adhesion in the normal direction, but weakens it in the shear direction. Altogether, these results allow progress toward mimicking the gecko's vertical mobility.

Influence of Short Austenitization Treatments on the Mechanical Properties of Low-Alloy Steels for Hot Forming Applications

Science.gov (United States)

Holzweissig, Martin Joachim; Lackmann, Jan; Konrad, Stefan; Schaper, Mirko; Niendorf, Thomas

2015-07-01

The current work elucidates an improvement of the mechanical properties of tool-quenched low-alloy steel by employing extremely short austenitization durations utilizing a press heating arrangement. Specifically, the influence of different austenitization treatments—involving austenitization durations ranging from three to 15 seconds—on the mechanical properties of low-alloy steel in comparison to an industrial standard furnace process was examined. A thorough set of experiments was conducted to investigate the role of different austenitization durations and temperatures on the resulting mechanical properties such as hardness, bending angle, tensile strength, and strain at fracture. The most important finding is that the hardness, the bending angle as well as the tensile strength increase with shortened austenitization durations. Furthermore, the ductility of the steels exhibits almost no difference following the short austenitization durations and the standard furnace process. The enhancement of the mechanical properties imposed by the short heat treatments investigated, is related to a refinement of microstructural features as compared to the standard furnace process.

Influence of innovative technologies on rheological and thermophysical properties of whey proteins and guar gum model systems

Directory of Open Access Journals (Sweden)

Greta Krešić

2011-03-01

Full Text Available The aim of this study was to examine the effect of high-power ultrasound (US and highpressure processing (HP on model systems composed of whey protein concentrate (WPC and whey protein isolate (WPI with or without guar gum addition. This kind of systems can be found in food production industry so the aim was to use novel food processing technologies to be utilized as a method for products development. Aqueous suspensions (10 g kg-1 of powdered whey proteins were treated with either ultrasound or high pressure. The treatment conditions were as follows: US: frequency of 30 kHz, for 5 and 10 min; HP: pressure intensity 300-600 MPa, for 5 and 10 min. Rheological and thermophysical properties were analyzed after guar gum addition (0.5 g kg-1. Ultrasound treatment showed a significant influence on all examined properties through protein denaturation caused by cavitation and microstreaming effects. High pressure caused significant increase in viscosity and consistency coefficients of model systems with and without guar addition. Significant decrease of initial freezing and initial thawing temperature was observed in all samples. With this research the direct influence of ultrasound and high-pressure treatment on the rheological and thermophysical properties of whey protein isolate and concentrate model systems with or without guar gum was demonstrated.

Microstructural characterization and influence of manufacturing parameters on technological properties of vitreous ceramic materials

Energy Technology Data Exchange (ETDEWEB)

Njoya, D. [Laboratoire de Physico-chimie des Materiaux Mineraux, Departement de Chimie Inorganique, Faculte des Sciences, Universite de Yaounde I, B.P. 812, Yaounde (Cameroon); Laboratoire de Physico-chimie des Materiaux et Environnement, Departement de Chimie, Faculte des Sciences Semlalia, Universite Cadi Ayyad, B.P. 2390, Marrakech (Morocco); Hajjaji, M., E-mail: Hajjaji@ucam.ac.ma [Laboratoire de Physico-chimie des Materiaux et Environnement, Departement de Chimie, Faculte des Sciences Semlalia, Universite Cadi Ayyad, B.P. 2390, Marrakech (Morocco); Bacaoui, A. [Laboratoire de Chimie Organique Appliquee, Departement de Chimie, Faculte des Sciences Semlalia, Universite Cadi Ayyad, B.P. 2390, Marrakech (Morocco); Njopwouo, D. [Laboratoire de Physico-chimie des Materiaux Mineraux, Departement de Chimie Inorganique, Faculte des Sciences, Universite de Yaounde I, B.P. 812, Yaounde (Cameroon)

2010-03-15

Microstructure of vitreous ceramic samples manufactured from kaolinitic-clay and feldspars raw materials from Cameroon was investigated in the range 1150-1250 deg. C by X-ray diffraction and scanning electron microscopy and by measuring some technological properties. Moreover, the simultaneous influence of feldspars content, heating temperature and soaking time on water absorption and firing shrinkage was evaluated by adopting the response surface methodology (Doehlert matrix), using the New Efficient Methodology for Research using Optimal Design (NEMROD) software. The results show that a spinel phase, mullite, glassy phase and some amount of hematite were formed. However, the spinel phase and potassic feldspar, as compared to the sodic one, disappeared at moderate firing temperature and soaking time. Apparently, mullite developed from spinel phase, which is formed from the demixion of metakaolin. On the other hand, it is found that the effects of fluxing content and firing temperature on the measured properties were almost similar and more influent than soaking time. Antagonistic and synergetic interactions existed between the considered parameters, and their importance differed for the considered properties. By using this mathematical tool, suitable operating conditions for manufacturing vitreous bodies were determined.

Microstructural characterization and influence of manufacturing parameters on technological properties of vitreous ceramic materials

International Nuclear Information System (INIS)

Njoya, D.; Hajjaji, M.; Bacaoui, A.; Njopwouo, D.

2010-01-01

Microstructure of vitreous ceramic samples manufactured from kaolinitic-clay and feldspars raw materials from Cameroon was investigated in the range 1150-1250 deg. C by X-ray diffraction and scanning electron microscopy and by measuring some technological properties. Moreover, the simultaneous influence of feldspars content, heating temperature and soaking time on water absorption and firing shrinkage was evaluated by adopting the response surface methodology (Doehlert matrix), using the New Efficient Methodology for Research using Optimal Design (NEMROD) software. The results show that a spinel phase, mullite, glassy phase and some amount of hematite were formed. However, the spinel phase and potassic feldspar, as compared to the sodic one, disappeared at moderate firing temperature and soaking time. Apparently, mullite developed from spinel phase, which is formed from the demixion of metakaolin. On the other hand, it is found that the effects of fluxing content and firing temperature on the measured properties were almost similar and more influent than soaking time. Antagonistic and synergetic interactions existed between the considered parameters, and their importance differed for the considered properties. By using this mathematical tool, suitable operating conditions for manufacturing vitreous bodies were determined.

Influence of Doping Concentration on Dielectric, Optical, and Morphological Properties of PMMA Thin Films

Directory of Open Access Journals (Sweden)

Lyly Nyl Ismail

2012-01-01

Full Text Available PMMA thin films were deposited by sol gel spin coating method on ITO substrates. Toluene was used as the solvent to dissolve the PMMA powder. The PMMA concentration was varied from 30 ~ 120 mg. The dielectric properties were measured at frequency of 0 ~ 100 kHz. The dielectric permittivity was in the range of 7.3 to 7.5 which decreased as the PMMA concentration increased. The dielectric loss is in the range of 0.01 ~ –0.01. All samples show dielectric characteristics which have dielectric loss is less than 0.05. The optical properties for thin films were measured at room temperature across 200 ~ 1000 nm wavelength region. All samples are highly transparent. The energy band gaps are in the range of 3.6 eV to 3.9 eV when the PMMA concentration increased. The morphologies of the samples show that all samples are uniform and the surface roughness increased as the concentration increased. From this study, it is known that, the dielectric, optical, and morphology properties were influenced by the amount of PMMA concentration in the solution.

Influence of trehalose 6,6'-diester (TDX) chain length on the physicochemical and immunopotentiating properties of DDA/TDX liposomes

DEFF Research Database (Denmark)

Kallerup, Rie Selchau; Madsen, Cecilie Maria; Schiøth, Mikkel Lohmann

2015-01-01

Linking physicochemical characterization to functional properties is crucial for defining critical quality attributes during development of subunit vaccines toward optimal safety and efficacy profiles. We investigated how the trehalose 6,6'-diester (TDX) chain length influenced the physicochemical...... and immunopotentiating properties of the clinically tested liposomal adjuvant composed of dimethyldioctadecylammonium (DDA) bromide and analogues of trehalose-6,6'-dibehenate (TDB). TDB analogues with symmetrically shortened acyl chains [denoted X: arachidate (A), stearate (S), palmitate (P), myristate (Myr) and laurate...

The influence of incontinence on the characteristic properties of the skin in bedridden elderly subjects.

Science.gov (United States)

Fujimura, Tsutomu; Makino, Mayumi; Takagi, Miyuki; Maki, Kumiko; Murakami, Emiko; Tasaka, Yoshiko; Sato, Noriko; Akiba, Shunichi; Hotta, Mitsuyuki; Kitahara, Takashi; Ando, Kikue

2016-05-01

The mechanisms of skin breakdown induced by incontinence have been proposed from a variety of experimental studies. However, studies on the influence of skin properties caused by incontinence of bedridden subjects are very limited. This work was conducted to reveal how incontinence influences skin properties by comparing bedridden incontinent elderly subjects with age-matched healthy continent elderly and middle-aged subjects. Bedridden incontinent elderly subjects (n = 35, 83.5 ± 9.7 years, mean age ± SD), healthy continent elderly (n = 41, 75.9 ± 5.6 years), and middle-aged (n = 20, 41.3 ± 2.8 years) were recruited for this study. Skin surface pH, capacitance/hydration, transepidermal water loss, and bacteria on forearm and buttock skin were measured. Hydration and transepidermal water loss values between healthy elderly subjects and incontinent elderly subjects were significantly different on buttock skin. Significant differences between those two groups were also observed regarding pH and total bacteria levels on buttock skin. The forearm skin showed no significant difference in these parameters. No significant influence was observed between with and without urination at the measurement time except for the pH of buttock skin. No significant correlation was observed except between pH and bacteria levels on buttock skin of incontinent elderly subjects. In this study, we clarified the characteristic features of skin induced by incontinence. Our results indicate that these parameters are adequate not only to evaluate the characteristic skin features of bedridden incontinent subjects but also to develop new diapers to avoid the diaper dermatitis caused by incontinence. © 2015 The International Society of Dermatology.

Influence of CaCO3 and SiO2 additives on magnetic properties of M-type Sr ferrites

Science.gov (United States)

Huang, Ching-Chien; Jiang, Ai-Hua; Hung, Yung-Hsiung; Liou, Ching-Hsuan; Wang, Yi-Chen; Lee, Chi-Ping; Hung, Tong-Yin; Shaw, Chun-Chung; Kuo, Ming-Feng; Cheng, Chun-Hu

2018-04-01

An experiment was carried out to investigate the influence of CaCO3 and SiO2 additives on the magnetic and physical properties of M-type Sr ferrites by changing experimental parameters such as the additive composition and Ca/Si ratio. Specimens were prepared by conventional ceramic techniques. It was found that the magnetic properties (Br = 4.42 kG, iHc = 3.32 kOe and (BH)max = 4.863 MGOe) were considerably improved upon adding CaCO3 = 1.1% and SiO2 = 0.4 wt% together with Co3O4, and the mechanical properties thereof were acceptable for motor applications. It was revealed that CaCO3 and SiO2 additives led to an upswing in the magnetic properties via the enhancement of uniform grain growth, particle alignment, and the densification of Sr ferrite.

A parametric study of influence of material properties on car cabin environment

Directory of Open Access Journals (Sweden)

Pokorny Jan

2014-03-01

Full Text Available Recently the author presented the paper describing a car cabin heat load model for the prediction of the car cabin environment. The model allowed to simulate a transient behavior of the car cabin, i.e. radiant temperature of surfaces, air temperature and relative humidity. The model was developed in Dymola and was built on the basic principles of thermodynamics and heat balance equations. The model was validated by experiments performed on the Škoda Felicia during various operational conditions. In this paper the authors present a parametric study investigating influence of material properties on a car cabin environment. The Matlab version of the car cabin heat load model has been developed and used. The model was extended by simple graphical user interface and it was deployed into the stand alone executable application. The aim of this parametric study is to identify most important material properties and its effect on the cabin environment during specific operational conditions of car. By means of a sensitive analysis it can identified which material parameters have to be defined precisely and which parameters are not so important for the prediction of the air temperature inside cabin.

The influence of non-magnetocaloric properties on the AMR performance

DEFF Research Database (Denmark)

Nielsen, Kaspar Kirstein; Bahl, Christian; Smith, Anders

2012-01-01

The performance of Active Magnetic Regenerators (AMR) does not depend solely on the magnetocaloric effect of their constituents. Rather, it depends on several additional parameters, including, magnetic field, geometry (hydraulic diameter, cross-sectional area, regenerator length etc.), thermal pr...... a strong dependence on the orientation of the applied field and the regenerator geometry. Finally, the flow maldistribution of non-uniform regenerator geometries is found to degrade the AMR performance even at minor deviations from perfectly homogeneous regenerator matrices.......The performance of Active Magnetic Regenerators (AMR) does not depend solely on the magnetocaloric effect of their constituents. Rather, it depends on several additional parameters, including, magnetic field, geometry (hydraulic diameter, cross-sectional area, regenerator length etc.), thermal...... properties (conductivity, specific heat and mass density) and operating parameters (utilization, frequency, number of transfer units etc.). In this paper we focus on the influence of three parameters on regenerator performance: 1) Solid thermal conductivity, 2) magnetostatic demagnetization and 3) flow...

Influence of the radio-frequency power on the physical and optical properties of plasma polymerized cyclohexane thin films

Energy Technology Data Exchange (ETDEWEB)

Manaa, C., E-mail: chadlia.el.manaa@gmail.com [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, UFR des Sciences d' Amiens, 33 rue Saint Leu, 80039 Amiens CEDEX 2 (France); Laboratoire des Matériaux Avancés et Phénomènes Quantiques, Université de Tunis El-Manar, Faculté des Sciences de Tunis, Campus universitaire El-Manar, 1068 Tunis (Tunisia); Lejeune, M. [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, UFR des Sciences d' Amiens, 33 rue Saint Leu, 80039 Amiens CEDEX 2 (France); Kouki, F. [Laboratoire des Matériaux Avancés et Phénomènes Quantiques, Université de Tunis El-Manar, Faculté des Sciences de Tunis, Campus universitaire El-Manar, 1068 Tunis (Tunisia); Durand-Drouhin, O. [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, UFR des Sciences d' Amiens, 33 rue Saint Leu, 80039 Amiens CEDEX 2 (France); Bouchriha, H. [Laboratoire des Matériaux Avancés et Phénomènes Quantiques, Université de Tunis El-Manar, Faculté des Sciences de Tunis, Campus universitaire El-Manar, 1068 Tunis (Tunisia); and others

2014-06-02

We investigate in the present study the effects of the radio-frequency plasma power on the opto-electronical properties of the polymeric amorphous hydrogenated carbon thin films deposited at room temperature and different radio-frequency powers by plasma-enhanced chemical vapor deposition method using cyclohexane as precursor. A combination of U.V.–Visible and infrared transmission measurements is applied to characterize the bonding and electronic properties of these films. Some film properties namely surface roughness, contact angle, surface energy, and optical properties are found to be significantly influenced by the radio-frequency power. The changes in these properties are analyzed within the microstructural modifications occurring during growth. - Highlights: • Effects of the radio-frequency power on the optoelectronic properties of thin films • Elaboration of plasma polymerized thin films using cyclohexane as precursor gas • The use of U.V.–Visible-infrared transmission, and optical gap • Study of the surface topography of the films by using Atomic Force microscopy • The use of a capacitively coupled plasma enhanced chemical vapor deposition method.

Influence of the radio-frequency power on the physical and optical properties of plasma polymerized cyclohexane thin films

International Nuclear Information System (INIS)

Manaa, C.; Lejeune, M.; Kouki, F.; Durand-Drouhin, O.; Bouchriha, H.

2014-01-01

We investigate in the present study the effects of the radio-frequency plasma power on the opto-electronical properties of the polymeric amorphous hydrogenated carbon thin films deposited at room temperature and different radio-frequency powers by plasma-enhanced chemical vapor deposition method using cyclohexane as precursor. A combination of U.V.–Visible and infrared transmission measurements is applied to characterize the bonding and electronic properties of these films. Some film properties namely surface roughness, contact angle, surface energy, and optical properties are found to be significantly influenced by the radio-frequency power. The changes in these properties are analyzed within the microstructural modifications occurring during growth. - Highlights: • Effects of the radio-frequency power on the optoelectronic properties of thin films • Elaboration of plasma polymerized thin films using cyclohexane as precursor gas • The use of U.V.–Visible-infrared transmission, and optical gap • Study of the surface topography of the films by using Atomic Force microscopy • The use of a capacitively coupled plasma enhanced chemical vapor deposition method

Influence of sorbitol on mechanical and physico-chemical properties of soy protein-based bioplastics processed by injection molding

Directory of Open Access Journals (Sweden)

Manuel Felix

Full Text Available Abstract Soy Protein Isolate (SPI has been evaluated as useful candidate for the development of protein-based bioplastic materials processed by injection molding. The influence of sorbitol (SB as plasticizer in mechanical properties and water uptake capacity was evaluated in SPI-based bioplastics. A mixing rheometer that allows monitoring torque and temperature during mixing and a small-scale-plunger-type injection molding machine were used to obtain SPI/Plasticizer blends and SPI-based bioplastics, respectively. Dynamic measurements were carried out to obtain mechanical spectra of different bioplastics. Moreover, the mechanical characterization was supplemented with uniaxial tensile tests. Additionally, the influence of SB in water uptake capacity was also evaluated. The introduction of SB leads to increase the rigidity of bioplastics as well as the water uptake capacity after 24h, however it involves a decrease in strain at break. Final bioplastics are plastic materials with both adequate properties for the substitution of conventional petroleum plastics and high biodegradability.

Influence of a powder feed rate on the properties of the plasma sprayed chromium carbide- 25% nickel chromium coating

Directory of Open Access Journals (Sweden)

Mihailo R. Mrdak

2014-04-01

Full Text Available Normal 0 false false false MicrosoftInternetExplorer4 The plasma spray process is a leading technology of powder depositing in the production of coatings widely used in the aerospace industry for the protection of new parts and for the repair of worn ones. Cermet 75Cr3C2 - 25Ni(Cr coatings based on Cr3C2 carbides are widely used to protect parts as they retain high values of hardness, strength and resistance to wear up to a temperature of 850°C. This paper discusses the influence of the parameters of the plasma spray deposition of 75Cr3C2 - 25Ni(Cr powder on the structure and mechanical properties of the coating. The powder is deposited using plasma spraying at atmospheric pressure (APS. The plasma gas is He, which is an inert gas and does not react with the powder; it produces dense plasma with lower heat content and less incorporated ambient air in the plasma jet thus reducing temperature decomposition and decarburization of Cr3C2 carbide.. In this study, three groups of coatings were deposited with three different powder feed rates of: 30, 45 and 60 g/min. The  coating with the best properties was deposited on the inlet flange parts of the turbo - jet engine TV2-117A to reduce the influence of vibrations and wear. The structures and the mechanical properties of 75Cr3C2 - 25Ni(Cr coatings are analyzed in accordance with the Pratt & Whitney standard. Studies have shown that powder feed rates have an important influence on the mechanical properties and structures of 75Cr3C2 - 25Ni(Cr coatings. 

Influence of dopant concentration on the electrical properties of the CdSe-PMMA nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Kaur, Ramneek; Tripathi, S. K., E-mail: surya@pu.ac.in, E-mail: surya-tr@yahoo.com [Department of Physics, Center of Advanced Study in Physics, Panjab University, Chandigarh-160 014 (India)

2016-05-06

This paper reports the synthesis and electrical characterization of CdSe-PMMA nanocomposite. CdSe-PMMA nanocomposite has been prepared by ex-situ technique through chemical route. The influence of three different Ag doping concentrations on the electrical properties has been studied in the temperature range ∼ 303-353 K. Transmission electron micrograph reveals the spherical morphology of the CdSe nanoparticles and their proper dispersion in the PMMA matrix. The electrical conduction of the polymer nanocomposites is through thermally activated process with single activation energy. With Ag doping, initially the activation energy increases upto 0.2 % Ag doping concentration but with further increase in Ag concentration, it decreases. This behavior has been discussed on the basis of randomly oriented grain boundaries and defect states. Thus, the results indicate that the transport properties of the polymer nanocomposites can be tailored by controlled doping concentration.

Influence of dopant concentration on the electrical properties of the CdSe-PMMA nanocomposite

International Nuclear Information System (INIS)

Kaur, Ramneek; Tripathi, S. K.

2016-01-01

This paper reports the synthesis and electrical characterization of CdSe-PMMA nanocomposite. CdSe-PMMA nanocomposite has been prepared by ex-situ technique through chemical route. The influence of three different Ag doping concentrations on the electrical properties has been studied in the temperature range ∼ 303-353 K. Transmission electron micrograph reveals the spherical morphology of the CdSe nanoparticles and their proper dispersion in the PMMA matrix. The electrical conduction of the polymer nanocomposites is through thermally activated process with single activation energy. With Ag doping, initially the activation energy increases upto 0.2 % Ag doping concentration but with further increase in Ag concentration, it decreases. This behavior has been discussed on the basis of randomly oriented grain boundaries and defect states. Thus, the results indicate that the transport properties of the polymer nanocomposites can be tailored by controlled doping concentration.

Nanocomposite permanent magnetic materials Nd-Fe-B type: The influence of nanocomposite on magnetic properties

Directory of Open Access Journals (Sweden)

Talijan Nadežda M.

2005-01-01

Full Text Available The influence on the magnetic properties of nanocristalline ribbons and powders has character of microstructure, between others – the grain size volume of hard and soft magnetic phases and their distribution. Magnetic properties of ribbons and powders depend mainly on their chemical composition and parameters of their heat treatment [1]. Technology of magnets from nanocristalline ribbon consists of the following process: preparing the Nd-Fe- B alloy, preparing the ribbon, powdering of the ribbon, heat treatment of the powder and finally preparing the magnets. Nanocomposite permanent magnet materials based on Nd-Fe- B alloy with Nd low content are a new type of permanent magnetic material. The microstructure of this nanocomposite permanent magnet is composed of a mixture of magnetically soft and hard phases which provide so called exchange coupling effect.

Investigations on the Mechanical Properties of Conducting Polymer Coating-Substrate Structures and Their Influencing Factors

Directory of Open Access Journals (Sweden)

Xin Hua

2009-12-01

Full Text Available This review covers recent advances and work on the microstructure features, mechanical properties and cracking processes of conducting polymer film/coatingsubstrate structures under different testing conditions. An attempt is made to characterize and quantify the relationships between mechanical properties and microstructure features. In addition, the film cracking mechanism on the micro scale and some influencing factors that play a significant role in the service of the film-substrate structure are presented. These investigations cover the conducting polymer film/coating nucleation process, microstructure-fracture characterization, translation of brittle-ductile fractures, and cracking processes near the largest inherent macromolecule defects under thermal-mechanical loadings, and were carried out using in situ scanning electron microscopy (SEM observations, as a novel method for evaluation of interface strength and critical failure stress.

Influence of the reaction stoichiometry on the mechanical and thermal properties of SWCNT-modified epoxy composites

International Nuclear Information System (INIS)

Ashrafi, Behnam; Johnston, Andrew; Martinez-Rubi, Yadienka; Kingston, Christopher T; Simard, Benoit; Khoun, Lolei; Yourdkhani, Mostafa; Hubert, Pascal

2013-01-01

Previous studies suggest that carbon nanotubes (CNTs) have a considerable influence on the curing behavior and crosslink density of epoxy resins. This invariably has an important effect on different thermal and mechanical properties of the epoxy network. This work focuses on the important role of the epoxy/hardener mixing ratio on the mechanical and thermal properties of a high temperature aerospace-grade epoxy (MY0510 Araldite as an epoxy and 4,4′-diaminodiphenylsulfone as an aromatic hardener) modified with single-walled carbon nanotubes (SWCNTs). The effects of three different stoichiometries (stoichiometric and off-stoichiometric) on various mechanical and thermal properties (fracture toughness, tensile properties, glass transition temperature) of the epoxy resin and its SWCNT-modified composites were obtained. The results were also supported by Raman spectroscopy and scanning electron microscopy (SEM). For the neat resin, it was found that an epoxy/hardener molar ratio of 1:0.8 provides the best overall properties. In contrast, the pattern in property changes with the reaction stoichiometry was considerably different for composites reinforced with unfunctionalized SWCNTs and reduced SWCNTs. A comparison among composites suggests that a 1:1 molar ratio considerably outperforms the other two ratios examined in this work (1:0.8 and 1:1.1). This composition at 0.2 wt% SWCNT loading provides the highest overall mechanical properties by improving fracture toughness, ultimate tensile strength and ultimate tensile strain of the epoxy resin by 40%, 34%, 54%, respectively. (paper)

Influences of sodium carbonate on physicochemical properties of lansoprazole in designed multiple coating pellets.

Science.gov (United States)

He, Wei; Yang, Min; Fan, Jun Hong; Feng, Cai Xia; Zhang, Su Juan; Wang, Jin Xu; Guan, Pei Pei; Wu, Wei

2010-09-01

Lansoprazole (LSP), a proton-pump inhibitor, belongs to class II drug. It is especially instable to heat, light, and acidic media, indicating that fabrication of a formulation stabilizing the drug is difficult. The addition of alkaline stabilizer is the most powerful method to protect the drug in solid formulations under detrimental environment. The purpose of the study was to characterize the designed multiple coating pellets of LSP containing an alkaline stabilizer (sodium carbonate) and assess the effect of the stabilizer on the physicochemical properties of the drug. The coated pellets were prepared by layer-layer film coating with a fluid-bed coater. In vitro release and acid-resistance studies were carried out in simulated gastric fluid and simulated intestinal fluid, respectively. Furthermore, the moisture-uptake test was performed to evaluate the influence of sodium carbonate on the drug stability. The results indicate that the drug exists in the amorphous state or small (nanometer size) particles without crystallization even after storage at 40°C/75% for 5 months. The addition of sodium carbonate to the pellet protects the drug from degradation in simulated gastric fluid in a dose-dependent manner. The moisture absorbed into the pellets has a detrimental effect on the drug stability. The extent of drug degradation is directly correlated with the content of moisture absorption. In conclusion, these results suggest that the presence of sodium carbonate influence the physicochemical properties of LSP, and the designed multiple coating pellets enhance the drug stability.

Chitosan as a Biomaterial: Influence of Degree of Deacetylation on Its Physiochemical, Material and Biological Properties.

Directory of Open Access Journals (Sweden)

Leslie John Ray Foster

Full Text Available Chitosan is a biomaterial with a range of current and potential biomedical applications. Manipulation of chitosan degree of deacetylation (DDA to achieve specific properties appears feasible, but studies investigating its influence on properties are often contradictory. With a view to the potential of chitosan in the regeneration of nerve tissue, the influence of DDA on the growth and health of olfactory ensheathing cells (OECs was investigated. There was a linear increase in OEC proliferation as the DDA increased from 72 to 85%. This correlated with linear increases in average surface roughness (0.62 to 0.78 μm and crystallinity (4.3 to 10.1% of the chitosan films. Mitochondrial activity and membrane integrity of OECs was significantly different for OECs cultivated on chitosan with DDAs below 75%, while those on films with DDAs up to 85% were similar to cells in asynchronous growth. Apoptotic indices and cell cycle analysis also suggested that chitosan films with DDAs below 75% were cytocompatible but induced cellular stress, while OECs grown on films fabricated from chitosan with DDAs above 75% showed no significant differences compared to those in asynchronous growth. Tensile strength and elongation to break varied with DDA from 32.3 to 45.3 MPa and 3.6 to 7.1% respectively. DDA had no significant influence on abiotic and biotic degradation profiles of the chitosan films which showed approximately 8 and 20% weight loss respectively. Finally, perceived patterns in property changes are subject to change based on potential variations in DDA analysis. NMR examination of the chitosan samples here revealed significant differences depending upon which peaks were selected for integration; 6 to 13% in DDA values within individual samples. Furthermore, differences between DDA values determined here and those reported by the commercial suppliers were significant and this may also be a source of concern when selecting commercial chitosans for