Wu, Lifu; Zhu, Jianguo; Xie, Huimin
2015-09-10
By using the principle of stereovision, 3D digital image correlation (3D-DIC) can determine the 3D morphology and deformation of a target and has been widely used in experimental mechanics as a noncontact 3D measurement technique. To eliminate the limitations of the conventional 3D-DIC system, this study proposes a calibration-free single-lens 3D-DIC system based on a bilateral telecentric lens and a bi-prism. The performance of the proposed system is verified by tests of rigid-body translation along the out-of-plane direction. As a comparison, the same rigid-body translations are measured using a single-entocentric-lens 3D-DIC system. The results show that the measurement accuracy of the proposed system is higher than that of the entocentric-lens-based one. As an application, the proposed system is used to measure the thermal linear expansion of a ceramic plate at elevated temperatures. The reasonable measurement results verify its applicability in deformation measurements, even in high-temperature environments.
Highly concentrating Fresnel lenses
International Nuclear Information System (INIS)
Kritchman, E.M.; Friesem, A.A.; Yekutieli, G.
1979-01-01
A new type of concave Fresnel lens capable of concentrating solar radiation very near the ultimate concentration limit is considered. The differential equations that describe the lens are solved to provide computed solutions which are then checked by ray tracing techniques. The performance (efficiency and concentration) of the lens is investigated and compared to that of a flat Fresnel lens, showing that the new lens is preferable for concentrating solar radiation. (author)
The fresnel interferometric imager
Koechlin, Laurent; Serre, Denis; Deba, Paul; Pelló, Roser; Peillon, Christelle; Duchon, Paul; Gomez de Castro, Ana Ines; Karovska, Margarita; Désert, Jean-Michel; Ehrenreich, David; Hebrard, Guillaume; Lecavelier Des Etangs, Alain; Ferlet, Roger; Sing, David; Vidal-Madjar, Alfred
2009-03-01
The Fresnel Interferometric Imager has been proposed to the European Space Agency (ESA) Cosmic Vision plan as a class L mission. This mission addresses several themes of the CV Plan: Exoplanet study, Matter in extreme conditions, and The Universe taking shape. This paper is an abridged version of the original ESA proposal. We have removed most of the technical and financial issues, to concentrate on the instrumental design and astrophysical missions. The instrument proposed is an ultra-lightweight telescope, featuring a novel optical concept based on diffraction focussing. It yields high dynamic range images, while releasing constraints on positioning and manufacturing of the main optical elements. This concept should open the way to very large apertures in space. In this two spacecraft formation-flying instrument, one spacecraft holds the focussing element: the Fresnel interferometric array; the other spacecraft holds the field optics, focal instrumentation, and detectors. The Fresnel array proposed here is a 3.6 ×3.6 m square opaque foil punched with 105 to 106 void “subapertures”. Focusing is achieved with no other optical element: the shape and positioning of the subapertures (holes in the foil) is responsible for beam combining by diffraction, and 5% to 10% of the total incident light ends up into a sharp focus. The consequence of this high number of subapertures is high dynamic range images. In addition, as it uses only a combination of vacuum and opaque material, this focussing method is potentially efficient over a very broad wavelength domain. The focal length of such diffractive focussing devices is wavelength dependent. However, this can be corrected. We have tested optically the efficiency of the chromatism correction on artificial sources (500 < λ < 750 nm): the images are diffraction limited, and the dynamic range measured on an artificial double source reaches 6.2 10 - 6. We have also validated numerical simulation algorithms for larger Fresnel
Martelli, C.; Canning, J.; Lyytikainen, K.; Groothoff, N.
2005-01-01
A water core photonic crystal Fresnel fiber exploiting a hole distribution on zone plates of a cylindrical waveguide was developed and characterized. This fiber has similar guiding properties as the pristine air-hole guiding fiber although a large loss edge ~900nm is observed indicating that the
Resonant inelastic scattering by use of geometrical optics.
Schulte, Jörg; Schweiger, Gustav
2003-02-01
We investigate the inelastic scattering on spherical particles that contain one concentric inclusion in the case of input and output resonances, using a geometrical optics method. The excitation of resonances is included in geometrical optics by use of the concept of tunneled rays. To get a quantitative description of optical tunneling on spherical surfaces, we derive appropriate Fresnel-type reflection and transmission coefficients for the tunneled rays. We calculate the inelastic scattering cross section in the case of input and output resonances and investigate the influence of the distribution of the active material in the particle as well as the influence of the inclusion on inelastic scattering.
Color corrected Fresnel lens for solar concentration
International Nuclear Information System (INIS)
Kritchman, E.M.
1979-01-01
A new linear convex Fresnel lens with its groove side down is described. The design philosophy is similar to the highly concentrating two focal Fresnel lens but including a correction for chromatic aberration. A solar concentration ratio as high as 80 is achieved. For wide acceptance angles the concentration nears the theoretical maximum. (author)
Stretchable Binary Fresnel Lens for Focus Tuning
Li, X.; Wei, L.; Poelma, R.H.; Vollebregt, S.; Wei, J.; Urbach, Paul; Sarro, P.M.; Zhang, G.Q.
2016-01-01
This paper presents a tuneable binary amplitude Fresnel lens produced by wafer-level microfabrication. The Fresnel lens is fabricated by encapsulating lithographically defined vertically aligned carbon nanotube (CNT) bundles inside a polydimethyl-siloxane (PDMS) layer. The composite lens material
Automated Fresnel lens tester system
Energy Technology Data Exchange (ETDEWEB)
Phipps, G.S.
1981-07-01
An automated data collection system controlled by a desktop computer has been developed for testing Fresnel concentrators (lenses) intended for solar energy applications. The system maps the two-dimensional irradiance pattern (image) formed in a plane parallel to the lens, whereas the lens and detector assembly track the sun. A point detector silicon diode (0.5-mm-dia active area) measures the irradiance at each point of an operator-defined rectilinear grid of data positions. Comparison with a second detector measuring solar insolation levels results in solar concentration ratios over the image plane. Summation of image plane energies allows calculation of lens efficiencies for various solar cell sizes. Various graphical plots of concentration ratio data help to visualize energy distribution patterns.
Development of Powerhouse Using Fresnel lens
Directory of Open Access Journals (Sweden)
Al-Dohani Nawar Saif
2018-01-01
Full Text Available Solar energy is an alternative source of renewable energy. Sultanate of Oman government showed initiation on utilization of solar energy for domestic and industrial applications. Fresnel lens is one of the methods to collect maximum energy by gathering heat of the sun in the concentrated form (using solar collectors. Earlier research work discloses that Fresnel lens gave better result in terms of power output and produces lower heat loss as compared to linear –parabolic solar collectors. In this work, development of a proto Fresnel lens power house was made to generate electricity. The focused heat from Fresnel lens was used to heat the molten salt in a heat exchanger to produce the steam. The generated steam was used to rotate the steam engine coupled to a generator. In the current work, a maximum power of 30 W was produced. In addition, comparative study was carried out regarding solar salts and heat exchanger materials to understand the Fresnel powerhouse performance. Overall the present study gave valuable information regarding usage of Fresnel lens for electricity generation in Oman.
Czech Academy of Sciences Publication Activity Database
Šmíd, Petr; Horváth, P.
2012-01-01
Roč. 29, č. 6 (2012), s. 1071-1077 ISSN 1084-7529 R&D Projects: GA MŠk(CZ) 1M06002; GA AV ČR KAN301370701 Institutional research plan: CEZ:AV0Z10100522 Keywords : Fresnel integrals * Fresnel diffraction Subject RIV: BH - Optics, Masers, Lasers Impact factor: 1.665, year: 2012
Astrophysical targets of the Fresnel diffractive imager
Koechlin, L.; Deba, P.; Raksasataya, T.
2017-11-01
The Fresnel Diffractive imager is an innovative concept of distributed space telescope, for high resolution (milli arc-seconds) spectro-imaging in the IR, visible and UV domains. This paper presents its optical principle and the science that can be done on potential astrophysical targets. The novelty lies in the primary optics: a binary Fresnel array, akin to a binary Fresnel zone plate. The main interest of this approach is the relaxed manufacturing and positioning constraints. While having the resolution and imaging capabilities of lens or mirrors of equivalent size, no optical material is involved in the focusing process: just vacuum. A Fresnel array consists of millions void subapertures punched into a large and thin opaque membrane, that focus light by diffraction into a compact and highly contrasted image. The positioning law of the aperture edges drives the image quality and contrast. This optical concept allows larger and lighter apertures than solid state optics, aiming to high angular resolution and high dynamic range imaging, in particular for UV applications. Diffraction focusing implies very long focal distances, up to dozens of kilometers, which requires at least a two-vessel formation flying in space. The first spacecraft, "the Fresnel Array spacecraft", holds the large punched foil: the Fresnel Array. The second, the "Receiver spacecraft" holds the field optics and focal instrumentation. A chromatism correction feature enables moderately large (20%) relative wavebands, and fields of a few to a dozen arc seconds. This Fresnel imager is adapted to high contrast stellar environments: dust disks, close companions and (we hope) exoplanets. Specific to the particular grid-like pattern of the primary focusing zone plate, is the very high dynamic range achieved in the images, in the case of compact objects. Large stellar photospheres may also be mapped with Fresnel arrays of a few meters opertaing in the UV. Larger and more complex fields can be imaged with
21 CFR 886.1390 - Flexible diagnostic Fresnel lens.
2010-04-01
... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Flexible diagnostic Fresnel lens. 886.1390 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1390 Flexible diagnostic Fresnel lens. (a) Identification. A flexible diagnostic Fresnel lens is a device that is a very thin lens which has...
Applications of the fresnel diffraction of neutrons
International Nuclear Information System (INIS)
Klein, A.G.; Opat, G.I.
1978-01-01
The place of Fresnel diffraction in the overall scheme of neutron interference experiments is outlined and possible applications are discussed in the areas of: magnetic domain visualisation; measurement of nuclear scattering lengths with very small specimens; focussing of long wavelength neutron beams using zone plates
Applications of the Fresnel diffraction of neutrons
International Nuclear Information System (INIS)
Klein, A.G.; Opat, G.I.
1978-01-01
The place of Fresnel diffraction in the overall scheme of neutron interference experiments is outlined and possible applications are discussed in the areas of: magnetic domain visualisation; measurement of nuclear scattering lengths with very small specimens; focussing of long wavelength neutron beams using zone plates
Progress In Fresnel-Köhler Concentrators
Mohedano, Rubén; Cvetković, Aleksandra; Benítez, Pablo; Chaves, Julio; Miñano, Juan C.; Zamora, Pablo; Hernandez, Maikel; Vilaplana, Juan
2011-12-01
The Fresnel Köhler (FK) concentrator was first presented in 2008. Since then, various CPV companies have adopted this technology as base for their future commercial product. The key for this rapid penetration is a mixture of simplicity (the FK is essentially a Fresnel lens concentrator, a technology that dominates the market) and excellent performance: high concentration without giving up large manufacturing/aiming tolerances, enabling high efficiency even at the array level. All these features together have a great potential to lower energy costs. This work shows recent results and progress regarding this device, covering new design features, measurements and tests along with first performance achievements at the array level (pilot 6.5 Kwp plant). The work also discusses the potential impact of the FK enhanced performance on the Levelized Cost Of Electricity (LCOE).
Numerical calculation of the Fresnel transform.
Kelly, Damien P
2014-04-01
In this paper, we address the problem of calculating Fresnel diffraction integrals using a finite number of uniformly spaced samples. General and simple sampling rules of thumb are derived that allow the user to calculate the distribution for any propagation distance. It is shown how these rules can be extended to fast-Fourier-transform-based algorithms to increase calculation efficiency. A comparison with other theoretical approaches is made.
ZEROES OF GENERALIZED FRESNEL COMPLEMENTARY INTEGRAL FUNCTIONS
Directory of Open Access Journals (Sweden)
Jaime Lobo Segura
2016-08-01
Full Text Available Theoretical upper and lower bounds are established for zeroes of a parametric family of functions which are deﬁned by integrals of the same type as the Fresnel complementary integral. Asymptotic properties for these bounds are obtained as well as monotony properties of the localization intervals. Given the value of the parameter an analytical-numerical procedure is deduced to enclose all zeros of a given function with an a priori error.
On the Fresnel sine integral and the convolution
Directory of Open Access Journals (Sweden)
Adem Kılıçman
2003-01-01
Full Text Available The Fresnel sine integral S(x, the Fresnel cosine integral C(x, and the associated functions S+(x, S−(x, C+(x, and C−(x are defined as locally summable functions on the real line. Some convolutions and neutrix convolutions of the Fresnel sine integral and its associated functions with x+r, xr are evaluated.
Development of Fresnel lens for improvement of rear visibility; Shikai kojo Fresnel lens no kaihatsu
Energy Technology Data Exchange (ETDEWEB)
Iwamoto, K; Sanada, C; Tsukino, M [Nissan Motor Co. Ltd., Tokyo (Japan)
1997-10-01
Fresnel lenses have been widely used to increase the visual field around vehicles for drivers. However, internal reflection in these lenses has been an obstacle in producing dear images. This internal glow is generated by incident light from an unexpected direction reflecting on the non-lens surface or radiating from the non-lens surface of the Fresnel lens. The cause of internal glow has been made dear combining louver film with the lens. The newly developed technology removes obstacles in producing dear images by reducing internal glow. 7 figs.
Linear Fresnel Spectrometer Chip with Gradient Line Grating
Choi, Sang Hyouk (Inventor); Park, Yeonjoon (Inventor)
2015-01-01
A spectrometer that includes a grating that disperses light via Fresnel diffraction according to wavelength onto a sensing area that coincides with an optical axis plane of the grating. The sensing area detects the dispersed light and measures the light intensity associated with each wavelength of the light. Because the spectrometer utilizes Fresnel diffraction, it can be miniaturized and packaged as an integrated circuit.
Terahertz wave tomographic imaging with a Fresnel lens
Institute of Scientific and Technical Information of China (English)
S. Wang; X.-C. Zhang
2003-01-01
We demonstrate three-dimensional tomographic imaging using a Fresnel lens with broadband terahertz pulses. Objects at various locations along the beam propagation path are uniquely imaged on the same imaging plane using a Fresnel lens with different frequencies of the imaging beam. This procedure allows the reconstruction of an object's tomographic contrast image by assembling the frequency-dependent images.
Adaption of optical Fresnel transform to optical Wigner transform
International Nuclear Information System (INIS)
Lv Cuihong; Fan Hongyi
2010-01-01
Enlightened by the algorithmic isomorphism between the rotation of the Wigner distribution function (WDF) and the αth fractional Fourier transform, we show that the optical Fresnel transform performed on the input through an ABCD system makes the output naturally adapting to the associated Wigner transform, i.e. there exists algorithmic isomorphism between ABCD transformation of the WDF and the optical Fresnel transform. We prove this adaption in the context of operator language. Both the single-mode and the two-mode Fresnel operators as the image of classical Fresnel transform are introduced in our discussions, while the two-mode Wigner operator in the entangled state representation is introduced for fitting the two-mode Fresnel operator.
DEFF Research Database (Denmark)
Hansen, Tim; Solomon, Gemma C.; Hansen, Thorsten
2017-01-01
In order to identify the location of an inelastic event and to distinguish between situations that are before or after this event, we derive equations for the interatomic inelastic transmission as a perturbation series in the electron-phonon interaction. This series contains both even and odd...... to second order and the 1st order correction represents the lowest order term of this new family of terms. We apply this to three model systems and are able to distinguish between situations before and after the inelastic event as steps in the 2nd order transmission. We also see that when the transmission...
Novel optical scanning cryptography using Fresnel telescope imaging.
Yan, Aimin; Sun, Jianfeng; Hu, Zhijuan; Zhang, Jingtao; Liu, Liren
2015-07-13
We propose a new method called modified optical scanning cryptography using Fresnel telescope imaging technique for encryption and decryption of remote objects. An image or object can be optically encrypted on the fly by Fresnel telescope scanning system together with an encryption key. For image decryption, the encrypted signals are received and processed with an optical coherent heterodyne detection system. The proposed method has strong performance through use of secure Fresnel telescope scanning with orthogonal polarized beams and efficient all-optical information processing. The validity of the proposed method is demonstrated by numerical simulations and experimental results.
Deep inelastic lepton scattering
International Nuclear Information System (INIS)
Nachtmann, O.
1977-01-01
Deep inelastic electron (muon) nucleon and neutrino nucleon scattering as well as electron positron annihilation into hadrons are reviewed from a theoretical point of view. The emphasis is placed on comparisons of quantum chromodynamics with the data. (orig.) [de
Bragg-Fresnel optics: New field of applications
Energy Technology Data Exchange (ETDEWEB)
Snigirev, A. [ESRF, Grenoble (France)
1997-02-01
Bragg-Fresnel Optics shows excellent compatibility with the third generation synchrotron radiation sources such as ESRF and is capable of obtaining monochromatic submicron focal spots with 10{sup 8}-10{sup 9} photons/sec in an energy bandwidth of 10{sup -4}-10{sup -6} and in a photon energy range between 2-100 keV. New types of Bragg-Fresnel lenses like modified, ion implanted, bent and acoustically modulated were tested. Microprobe techniques like microdiffraction and microfluorescence based on Bragg-Fresnel optics were realised at the ESRF beamlines. Excellent parameters of the X-ray beam at the ESRF in terms of low emittance and quite small angular source size allow for Bragg-Fresnel optics to occupy new fields of applications such as high resolution diffraction, holography, interferometry and phase contrast imaging.
Design of a nonimaging Fresnel lens for solar concentrators
Energy Technology Data Exchange (ETDEWEB)
Leutz, R.; Akisawa, Atushi; Kashiwagi, Takao [Tokyo University of Agriculture and Technology (Japan). Dept. of Mechanical Systems Engineering; Suzuki, Akio [UNESCO, Paris (France)
1999-04-01
An optimum convex shaped nonimaging Fresnel lens is designed following the edge ray principle. The lens is evaluated by tracing rays and calculating a projective optical concentration ratio. This Fresnel lens is intended for use in evacuated tube type solar concentrators, generating mid-temperature heat to drive sorption cycles, or provide industrial process heat. It can also be used along with a secondary concentrator in photovoltaic applications. (author)
Signal-enhancement reflective pulse oximeter with Fresnel lens
Chung, Shuang-Chao; Sun, Ching-Cherng
2016-09-01
In this paper, a new reflective pulse oximeter is proposed and demonstrated with implanting a Fresnel lens, which enhances the reflected signal. An optical simulation model incorporated with human skin characteristics is presented to evaluate the capability of the Fresnel lens. In addition, the distance between the light emitting diode and the photodiode is optimized. Compared with the other reflective oximeters, the reflected signal light detected by the photodiode is enhanced to more than 140%.
Optical modeling of Fresnel zoneplate microscopes
International Nuclear Information System (INIS)
Naulleau, Patrick P.; Mochi, Iacopo; Goldberg, Kenneth A.
2011-01-01
Defect free masks remain one of the most significant challenges facing the commercialization of extreme ultraviolet (EUV) lithography. Progress on this front requires high-performance wavelength-specific metrology of EUV masks, including high-resolution and aerial-image microscopy performed near the 13.5 nm wavelength. Arguably the most cost-effective and rapid path to proliferating this capability is through the development of Fresnel zoneplate-based microscopes. Given the relative obscurity of such systems, however, modeling tools are not necessarily optimized to deal with them and their imaging properties are poorly understood. Here we present a modeling methodology to analyze zoneplate microscopes based on commercially available optical modeling software and use the technique to investigate the imaging performance of an off-axis EUV microscope design. The modeling predicts that superior performance can be achieved by tilting the zoneplate, making it perpendicular to the chief ray at the center of the field, while designing the zoneplate to explicitly work in that tilted plane. Although the examples presented here are in the realm of EUV mask inspection, the methods described and analysis results are broadly applicable to zoneplate microscopes in general, including full-field soft-x-ray microscopes routinely used in the synchrotron community.
International Nuclear Information System (INIS)
Aubert, J.J.
1982-01-01
Deep inelastic lepton-nucleon interaction experiments are renewed. Singlet and non-singlet structure functions are measured and the consistency of the different results is checked. A detailed analysis of the scaling violation is performed in terms of the quantum chromodynamics predictions [fr
Fresnel's phase observation by means of the pinhole Young's experiment
International Nuclear Information System (INIS)
Medina, F.F.; Matteucci, G.
2000-04-01
Using the conventional Young's experiment with two pinholes, we observe the shift effect of the Fresnel's phase on the interference patterns, by measuring its intensity on the optical axis. It allows us to propose a criterion for distinguishing between Fraunhofer and Fresnel diffraction. Indeed, in the Fraunhofer domain the Young's patterns will be centered on the optical axis. As a consequence, only constructive interference will occur at this point. But in the Fresnel domain, the Young's patterns will be laterally shifted in such a way that constructive and destructive interference will occur alternatively on the optical axis, and the intensity of the diffraction pattern at this point will oscillate. Extended diffracting apertures can be analyzed as ensembles of Young's pairs of wavelet sources. From this point of view, the intensity distribution they produce on the detector plane results from the superposition of all their interference patterns. (author)
Digital reconstruction of Young's fringes using Fresnel transformation
Kulenovic, Rudi; Song, Yaozu; Renninger, P.; Groll, Manfred
1997-11-01
This paper deals with the digital numerical reconstruction of Young's fringes from laser speckle photography by means of the Fresnel-transformation. The physical model of the optical reconstruction of a specklegram is a near-field Fresnel-diffraction phenomenon which can be mathematically described by the Fresnel-transformation. Therefore, the interference phenomena can be directly calculated by a microcomputer.If additional a CCD-camera is used for specklegram recording the measurement procedure and evaluation process can be completely carried out in a digital way. Compared with conventional laser speckle photography no holographic plates, no wet development process and no optical specklegram reconstruction are needed. These advantages reveal a wide future in scientific and engineering applications. The basic principle of the numerical reconstruction is described, the effects of experimental parameters of Young's fringes are analyzed and representative results are presented.
An amplitude and phase hybrid modulation Fresnel diffractive optical element
Li, Fei; Cheng, Jiangao; Wang, Mengyu; Jin, Xueying; Wang, Keyi
2018-04-01
An Amplitude and Phase Hybrid Modulation Fresnel Diffractive Optical Element (APHMFDOE) is proposed here. We have studied the theory of APHMFDOE and simulated the focusing properties of it along the optical axis, which show that the focus can be blazed to other positions with changing the quadratic phase factor. Moreover, we design a Composite Fresnel Diffraction Optical Element (CFDOE) based on the characteristics of APHMFDOE. It greatly increases the outermost zone width without changing the F-number, which brings a lot of benefits to the design and processing of diffraction device. More importantly, the diffraction efficiency of the CFDOE is almost unchanged compared with AFZP at the same focus.
Evolutionary algorithm for optimization of nonimaging Fresnel lens geometry.
Yamada, N; Nishikawa, T
2010-06-21
In this study, an evolutionary algorithm (EA), which consists of genetic and immune algorithms, is introduced to design the optical geometry of a nonimaging Fresnel lens; this lens generates the uniform flux concentration required for a photovoltaic cell. Herein, a design procedure that incorporates a ray-tracing technique in the EA is described, and the validity of the design is demonstrated. The results show that the EA automatically generated a unique geometry of the Fresnel lens; the use of this geometry resulted in better uniform flux concentration with high optical efficiency.
Miniaturization of Fresnel lenses for solar concentration: a quantitative investigation.
Duerr, Fabian; Meuret, Youri; Thienpont, Hugo
2010-04-20
Sizing down the dimensions of solar concentrators for photovoltaic applications offers a number of promising advantages. It provides thinner modules and smaller solar cells, which reduces thermal issues. In this work a plane Fresnel lens design is introduced that is first analyzed with geometrical optics. Because of miniaturization, pure ray tracing may no longer be valid to determine the concentration performance. Therefore, a quantitative wave optical analysis of the miniaturization's influence on the obtained concentration performance is presented. This better quantitative understanding of the impact of diffraction in microstructured Fresnel lenses might help to optimize the design of several applications in nonimaging optics.
International Nuclear Information System (INIS)
Zakharov, V.I.
1977-01-01
The present status of the quark-parton-gluon picture of deep inelastic scattering is reviewed. The general framework is mostly theoretical and covers investigations since 1970. Predictions of the parton model and of the asymptotically free field theories are compared with experimental data available. The valence quark approximation is concluded to be valid in most cases, but fails to account for the data on the total momentum transfer. On the basis of gluon corrections introduced to the parton model certain predictions concerning both the deep inelastic structure functions and form factors are made. The contributions of gluon exchanges and gluon bremsstrahlung are highlighted. Asymptotic freedom is concluded to be very attractive and provide qualitative explanation to some experimental observations (scaling violations, breaking of the Drell-Yan-West type relations). Lepton-nuclear scattering is pointed out to be helpful in probing the nature of nuclear forces and studying the space-time picture of the parton model
Sputtering and inelastic processes
International Nuclear Information System (INIS)
Baranov, I.A.; Tsepelevic, S.O.
1987-01-01
Experimental data and models of a new type of material sputtering with ions of relatively high energies due to inelastic (electron) processes are reviewed. This area of investigations began to develop intensively during the latest years. New experimental data of the authors on differential characteristics of ultradisperse gold and americium dioxide layers with fission fragments are given as well. Practical applications of the new sputtering type are considered as well as setup of possibl experiments at heavy multiply charged ion accelerators
Huygens-Fresnel principle: Analyzing consistency at the photon level
Santos, Elkin A.; Castro, Ferney; Torres, Rafael
2018-04-01
Typically the use of the Rayleigh-Sommerfeld diffraction formula as a photon propagator is widely accepted due to the abundant experimental evidence that suggests that it works. However, a direct link between the propagation of the electromagnetic field in classical optics and the propagation of photons where the square of the probability amplitude describes the transverse probability of the photon detection is still an issue to be clarified. We develop a mathematical formulation for the photon propagation using the formalism of electromagnetic field quantization and the path-integral method, whose main feature is its similarity with a fractional Fourier transform (FRFT). Here we show that because of the close relation existing between the FRFT and the Fresnel diffraction integral, this propagator can be written as a Fresnel diffraction, which brings forward a discussion of the fundamental character of it at the photon level compared to the Huygens-Fresnel principle. Finally, we carry out an experiment of photon counting by a rectangular slit supporting the result that the diffraction phenomenon in the Fresnel approximation behaves as the actual classical limit.
Replica casting technique for micro Fresnel lenses characterization
DEFF Research Database (Denmark)
Gasparin, Stefania; Tosello, Guido; Hansen, Hans Nørgaard
2012-01-01
The available measuring techniques are not always suitable for the characterization of optical surfaces such as Fresnel lenses or polished specimens. A way to overcome these challenges is to reproduce the optical components surface using a polymer casting method and to measure the replicated...
The temporal Fresnel number in terms of ray matrix elements
International Nuclear Information System (INIS)
Zhang Zhuhong; Fan Dianyuan
1993-01-01
By using the analogy between temporal ray matrix and the well known ray matrix, the temporal Fresnel number, which gives the qualitative and quasiquantitative characteristics (shape, width and chirp) of optical pulses, is derived. A concept of effective propagation time is introduced. Several typical examples are discussed. 6 refs
Fresnel representation of the Wigner function: an operational approach.
Lougovski, P; Solano, E; Zhang, Z M; Walther, H; Mack, H; Schleich, W P
2003-07-04
We present an operational definition of the Wigner function. Our method relies on the Fresnel transform of measured Rabi oscillations and applies to motional states of trapped atoms as well as to field states in cavities. We illustrate this technique using data from recent experiments in ion traps [Phys. Rev. Lett. 76, 1796 (1996)
Daylighting System Based on Novel Design of Linear Fresnel lens
Directory of Open Access Journals (Sweden)
Thanh Tuan Pham
2017-10-01
Full Text Available In this paper, we present a design and optical simulation of a daylighting system using a novel design of linear Fresnel lens, which is constructed based on the conservation of optical path length and edge ray theorem. The linear Fresnel lens can achieve a high uniformity by using a new idea of design in which each groove of the lens distributes sunlight uniformly over the receiver so that the whole lens also uniformly distributes sunlight over the receiver. In this daylighting system, the novel design of linear Fresnel lens significantly improves the uniformity of collector and distributor. Therefore, it can help to improve the performance of the daylighting system. The structure of the linear Fresnel lenses is designed by using Matlab. Then, the structure of lenses is appreciated by ray tracing in LightToolsTM to find out the optimum lens shape. In addition, the simulation is performed by using LightToolsTM to estimate the efficiency of the daylighting system. The results show that the designed collector can achieve the efficiency of ~80% with the tolerance of ~0.60 and the concentration ratio of 340 times, while the designed distributor can reach a high uniformity of >90%.
High resolution Fresnel zone plate laser alignment system
International Nuclear Information System (INIS)
Bressler, V.E.; Fischer, G.E.; Ruland, R.E.; Wang, T.
1992-03-01
The existing Fresnel zone plate laser alignment system is currently being extended and upgraded for the Final Focus Test Beam (FFTB). Previously, the resolution of this system has been several tens of micrometers. After the upgrade, the resolution will be a few micrometers. Details of the upgrade as well as simulation and experimental results will be presented
Improvements on Fresnel arrays for high contrast imaging
Wilhem, Roux; Laurent, Koechlin
2018-03-01
The Fresnel Diffractive Array Imager (FDAI) is based on a new optical concept for space telescopes, developed at Institut de Recherche en Astrophysique et Planétologie (IRAP), Toulouse, France. For the visible and near-infrared it has already proven its performances in resolution and dynamic range. We propose it now for astrophysical applications in the ultraviolet with apertures from 6 to 30 meters, aimed at imaging in UV faint astrophysical sources close to bright ones, as well as other applications requiring high dynamic range. Of course the project needs first a probatory mission at small aperture to validate the concept in space. In collaboration with institutes in Spain and Russia, we will propose to board a small prototype of Fresnel imager on the International Space Station (ISS), with a program combining technical tests and astrophysical targets. The spectral domain should contain the Lyman- α line ( λ = 121 nm). As part of its preparation, we improve the Fresnel array design for a better Point Spread Function in UV, presently on a small laboratory prototype working at 260 nm. Moreover, we plan to validate a new optical design and chromatic correction adapted to UV. In this article we present the results of numerical propagations showing the improvement in dynamic range obtained by combining and adapting three methods : central obturation, optimization of the bars mesh holding the Fresnel rings, and orthogonal apodization. We briefly present the proposed astrophysical program of a probatory mission with such UV optics.
Optimization of insulation of a linear Fresnel collector
Ardekani, Mohammad Moghimi; Craig, Ken J.; Meyer, Josua P.
2017-06-01
This study presents a simulation based optimization study of insulation around the cavity receiver of a Linear Fresnel Collector. This optimization study focuses on minimizing heat losses from a cavity receiver (maximizing plant thermal efficiency), while minimizing insulation cross-sectional area (minimizing material cost and cavity dead load), which leads to a cheaper and thermally more efficient LFC cavity receiver.
Up scaling and test results of an advanced Fresnel greenhouse
Sonneveld, P.J.; Swinkels, G.L.A.M.; Tuijl, van B.A.J.; Janssen, H.J.J.; Zwart, de H.F.
2012-01-01
A greenhouse with Fresnel lenses in the south facing roof and a receiver for concentrated Photovoltaics with water cooling (CPVT system) will result in electrical and thermal energy output from the solar energy excess entering a greenhouse. The PV system converts about half of the direct radiation
Lightweight Inexpensive Ozone Lidar Telescope Using a Plastic Fresnel Lens
DeYoung, Russell J.; Notari, Anthony; Carrion, William; Pliutau, Denis
2014-01-01
An inexpensive lightweight ozone lidar telescope was designed, constructed and operated during an ozone lidar field campaign. This report summarizes the design parameters and performance of the plastic Fresnel lens telescope and shows the ozone lidar performance compared to Zemax calculations.
Energy Technology Data Exchange (ETDEWEB)
Frabboni, Stefano [Department FIM, University of Modena and Reggio Emilia, Via G. Campi 213/a, 41125 Modena (Italy); CNR-Institute of Nanoscience-S3, Via G. Campi 213/a, 41125 Modena (Italy); Gazzadi, Gian Carlo [CNR-Institute of Nanoscience-S3, Via G. Campi 213/a, 41125 Modena (Italy); Grillo, Vincenzo [CNR-Institute of Nanoscience-S3, Via G. Campi 213/a, 41125 Modena (Italy); CNR-IMEM, Parco delle Scienze 37a, 43100 Parma (Italy); Pozzi, Giulio [Department of Physics and Astronomy, University of Bologna, Viale B. Pichat 6/2, 40127 Bologna (Italy)
2015-07-15
Modern nanotechnology tools allowed us to prepare slits of 90 nm width and 450 nm spacing in a screen almost completely opaque to 200 keV electrons. Then by covering both slits with a layer of amorphous material and carrying out the experiment in a conventional transmission electron microscope equipped with an energy filter we can demonstrate that the diffraction pattern, taken by selecting the elastically scattered electrons, shows the presence of interference fringes, but with a bimodal envelope which can be accounted for by taking into account the non-constant thickness of the deposited layer. However, the intensity of the inelastically scattered electrons in the diffraction plane is very broad and at the limit of detectability. Therefore the experiment was repeated using an aluminum film and a microscope also equipped with a Schottky field emission gun. It was thus possible to observe also the image due to the inelastically scattered electron, which does not show interference phenomena both in the Fraunhofer or Fresnel regimes. If we assume that inelastic scattering through the thin layer covering the slits provides the dissipative process of interaction responsible for the localization mechanism, then these experiments can be considered a variant of the Feynman which-way thought experiment. - Highlights: • Fabrication by focused ion beam and electron beam induced deposition of two slits covered by electron transparent materials. • Two slits interference experiment with elastic and inelastic electrons. • Analysis of Fraunhofer and Fresnel images of the two slits formed with elastic and inelastic (plasmon loss) electrons.
Inelastic scattering of neutrons
International Nuclear Information System (INIS)
Sal'nikov, O.A.
1984-06-01
The paper reviews the main problems concerning the mechanism of the inelastic scatterings of neutrons by nuclei, concentrating on the different models which calculate the angular distributions. In the region of overlapping levels, both the compound nucleus mechanism and the preequilibrium Griffin (exciton) model are discussed, and their contribution relative to that of a direct mechanism is considered. The parametrization of the level density and of the nuclear moment of inertia are also discussed. The excitation functions of discrete levels are also presented, and the importance of elucidating their five structure (for practical calculations, such as for shielding) is pointed out
Deep inelastic neutron scattering
International Nuclear Information System (INIS)
Mayers, J.
1989-03-01
The report is based on an invited talk given at a conference on ''Neutron Scattering at ISIS: Recent Highlights in Condensed Matter Research'', which was held in Rome, 1988, and is intended as an introduction to the techniques of Deep Inelastic Neutron Scattering. The subject is discussed under the following topic headings:- the impulse approximation I.A., scaling behaviour, kinematical consequences of energy and momentum conservation, examples of measurements, derivation of the I.A., the I.A. in a harmonic system, and validity of the I.A. in neutron scattering. (U.K.)
Polarization phenomena in inelastic scattering
International Nuclear Information System (INIS)
Verhaar, B.J.
1974-01-01
An attempt is made to clarify the principles of inelastic scattering using the distorted wave Born approximation, concentrating on inelastic proton scattering. The principle aspects and merits of the microscopic description and the necessity of including the N-N spin orbit force are discussed. (7 figures) (U.S.)
Directory of Open Access Journals (Sweden)
Robert de Mello Koch
2017-05-01
Full Text Available We study the worldsheet S-matrix of a string attached to a D-brane in AdS5×S5. The D-brane is either a giant graviton or a dual giant graviton. In the gauge theory, the operators we consider belong to the su(2|3 sector of the theory. Magnon excitations of open strings can exhibit both elastic (when magnons in the bulk of the string scatter and inelastic (when magnons at the endpoint of an open string participate scattering. Both of these S-matrices are determined (up to an overall phase by the su(2|22 global symmetry of the theory. In this note we study the S-matrix for inelastic scattering. We show that it exhibits poles corresponding to boundstates of bulk and boundary magnons. A crossing equation is derived for the overall phase. It reproduces the crossing equation for maximal giant gravitons, in the appropriate limit. Finally, scattering in the su(2 sector is computed to two loops. This two loop result, which determines the overall phase to two loops, will be useful when a unique solution to the crossing equation is to be selected.
Advanced split-illumination electron holography without Fresnel fringes
Energy Technology Data Exchange (ETDEWEB)
Tanigaki, Toshiaki, E-mail: tanigaki-toshiaki@riken.jp [Center for Emergent Matter Science (CEMS), RIKEN, Hirosawa 2-1, Wako, Saitama 351-0198 (Japan); Aizawa, Shinji; Park, Hyun Soon [Center for Emergent Matter Science (CEMS), RIKEN, Hirosawa 2-1, Wako, Saitama 351-0198 (Japan); Matsuda, Tsuyoshi [Japan Science and Technology Agency, Kawaguchi, Saitama 332-0012 (Japan); Harada, Ken [Central Research Laboratory, Hitachi, Ltd., Hatoyama, Saitama 350-0395 (Japan); Shindo, Daisuke [Center for Emergent Matter Science (CEMS), RIKEN, Hirosawa 2-1, Wako, Saitama 351-0198 (Japan); Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, Katahira 2-1-1, Sendai 980-8577 (Japan)
2014-02-01
Advanced split-illumination electron holography was developed by employing two biprisms in the illuminating system to split an electron wave into two coherent waves and two biprisms in the imaging system to overlap them. A focused image of an upper condenser-biprism filament was formed on the sample plane, and all other filaments were placed in its shadow. This developed system makes it possible to obtain precise reconstructed object waves without modulations due to Fresnel fringes, in addition to holograms of distant objects from reference waves. - Highlights: • Advanced split-illumination electron holography without Fresnel fringes is developed. • Two biprisms are installed in illuminating system of microscope. • High-precision holographic observations of an area locating far from the sample edge become possible.
Advanced split-illumination electron holography without Fresnel fringes
International Nuclear Information System (INIS)
Tanigaki, Toshiaki; Aizawa, Shinji; Park, Hyun Soon; Matsuda, Tsuyoshi; Harada, Ken; Shindo, Daisuke
2014-01-01
Advanced split-illumination electron holography was developed by employing two biprisms in the illuminating system to split an electron wave into two coherent waves and two biprisms in the imaging system to overlap them. A focused image of an upper condenser-biprism filament was formed on the sample plane, and all other filaments were placed in its shadow. This developed system makes it possible to obtain precise reconstructed object waves without modulations due to Fresnel fringes, in addition to holograms of distant objects from reference waves. - Highlights: • Advanced split-illumination electron holography without Fresnel fringes is developed. • Two biprisms are installed in illuminating system of microscope. • High-precision holographic observations of an area locating far from the sample edge become possible
Babinet's principle in the Fresnel regime studied using ultrasound
Hitachi, Akira; Takata, Momo
2010-07-01
The diffraction of ultrasound by a circular disk and an aperture of the same size has been investigated as a demonstration of Babinet's principle in the Fresnel regime. The amplitude and the phase of the diffracted ultrasonic waves are measured and a graphical treatment of the results is performed by drawing vectors in the complex plane. The results verify Babinet's principle. It is also found that the incident wave is π /2 behind the phase of the wave passing through on the central axis of a circular aperture. Because both waves travel the same path and the same distance, they should be in phase. This paradox has previously been regarded as a defect of Fresnel's theory.
Angular criterion for distinguishing between Fraunhofer and Fresnel diffraction
International Nuclear Information System (INIS)
Medina, Francisco F.; Garcia-Sucerquia, Jorge; Castaneda, Roman; Matteucci, Giorgio
2003-03-01
The distinction between Fresnel and Fraunhofer diffraction is a crucial condition for the accurate analysis of diffracting structures. In this paper we propose a criterion based on the angle subtended by the first zero of the diffraction pattern from the center of the diffracting aperture. The determination of the zero of the diffraction pattern is the crucial point for assuring the precision of the criterion. It mainly depends on the dynamical range of the detector. Therefore, the applicability of adequate thresholds for different detector types is discussed. The criterion is also generalized by expressing it in terms of the number of Fresnel zones delimited by the aperture. Simulations are reported for illustrating the feasibility of the criterion. (author)
Effect of Fresnel Reflectivity in a Spherical Turbid Medium
Elghazaly, A
2003-01-01
Radiative transfer problem for anisotropic scattering in a spherical homogeneous, turbid medium with angular dependent (specular) reflecting boundary is solved using the pomraning-Eddington approximation method. The angular dependent reflectivity of the boundary is considered as Fresnel's reflection probability function. The partial heat flux is calculated with anisotropic scattering through a homogeneous solid sphere. our results are compared with the available data and give an excellent agreement.
Effect of Fresnel Reflectivity in a Spherical Turbid Medium
International Nuclear Information System (INIS)
Elghazaly, A.; Attia, M.T.
2003-01-01
Radiative transfer problem for anisotropic scattering in a spherical homogeneous, turbid medium with angular dependent (specular) reflecting boundary is solved using the pomraning-Eddington approximation method. The angular dependent reflectivity of the boundary is considered as Fresnel's reflection probability function. The partial heat flux is calculated with anisotropic scattering through a homogeneous solid sphere. our results are compared with the available data and give an excellent agreement
Zeroes of functions of Fresnel complementary integral type
Directory of Open Access Journals (Sweden)
Mario Alberto Villalobos Arias
2017-02-01
Full Text Available Theoretical upper and lower bounds are established for zeroes of a parametric family of functions which are defined by integrals of the same type as the Fresnel complementary integral. Asymptotic properties for these bounds are obtained as well as monotony properties of the localization intervals. Given the value of the parameter an analytical-numerical procedure is deduced to enclose all zeros of a given function with an a priori error.
Design and construction of a Fresnel linear distiller
International Nuclear Information System (INIS)
Saettone, E.
2014-01-01
It was designed a Fresnel linear distiller based on optical calculations obtained from taking into account Lima's latitude value, Earth inclination angle and heat absorber cavity's dimensions. The 5.6 m 2 reflective surface concentrator of the distiller was constructed with 32 plane rectangular mirrors; the heat absorber cavity was made with a rectangular blackened aluminum tube 1 m long and installed 2.5 m over the plane of mirrors. The Fresnel linear distiller was installed at the University of Lima and experimental tests were performed during no cloudy summer days. There were measured ambient temperature, heat absorber cavity temperature, radiant flux and fresh water volume. From this, it was obtained a production of 0.89 liters/hour and 0.79 L/m 2 , and it was calculated a total performance of 34.5% in desalting sea water. Finally, it is presented a comparison between Fresnel linear distiller (FLD) and parabolic trough distiller (PTD) with similar dimensions and characteristics. It is obtained that the last one produced almost 32% more fresh water than the former, but at the same time, the FLD is almost 20% cheaper than PTD. However, water cost production with both distillers using is almost the same. (author)
Cylindrically symmetric Fresnel lens for high concentration photovoltaic
Hung, Yu-Ting; Su, Guo-Dung
2009-08-01
High concentration photovoltaic (HCPV) utilizes point-focus cost-effective plastic Fresnel lens. And a millimeter-sized Ill-V compound multi-junction solar cell is placed underneath focusing optics which can achieve cell efficiency potential of up to 40.7 %. The advantage of HCPV makes less solar cell area and higher efficiency; however, the acceptance angle of HCPV is about +/-1°, which is very small and the mechanical tracking of the sun is necessary. In order to reduce the power consumption and the angle tracking error of tracking systems, a light collector model with larger acceptance angle is designed with ZEMAXÂ®. In this model, the original radially symmetric Fresnel lens of HCPV is replaced by cylindrically symmetric Fresnel lens and a parabolic reflective surface. Light is collected in two dimensions separately. And a couple of lenses and a light pipe are added before the solar cell chip in order to collect more light when sun light deviates from incident angle of 00. An acceptance angle of +/-10° is achieved with GCR 400.
International Nuclear Information System (INIS)
Smith, David; Weiner, Neal
2001-01-01
Many observations suggest that much of the matter of the universe is nonbaryonic. Recently, the DAMA NaI dark matter direct detection experiment reported an annual modulation in their event rate consistent with a WIMP relic. However, the Cryogenic Dark Matter Search (CDMS) Ge experiment excludes most of the region preferred by DAMA. We demonstrate that if the dark matter can only scatter by making a transition to a slightly heavier state (Δm∼100 keV), the experiments are no longer in conflict. Moreover, differences in the energy spectrum of nuclear recoil events could distinguish such a scenario from the standard WIMP scenario. Finally, we discuss the sneutrino as a candidate for inelastic dark matter in supersymmetric theories
International Nuclear Information System (INIS)
Aubert, J.J.
1982-01-01
The experimental situation of the deep inelastic scattering for electrons (muons) is reviewed. A brief history of experimentation highlights Mohr and Nicoll's 1932 experiment on electron-atom scattering and Hofstadter's 1950 experiment on electron-nucleus scattering. The phenomenology of electron-nucleon scattering carried out between 1960 and 1970 is described, with emphasis on the parton model, and scaling. Experiments at SLAC and FNAL since 1974 exhibit scaling violations. Three muon-nucleon scattering experiments at BFP, BCDMA, and EMA, currently producing new results in the high Q 2 domain suggest a rather flat behaviour of the structure function at fixed x as a function of Q 2 . It is seen that the structure measured in DIS can then be projected into a pure hadronic process to predict a cross section. Protonneutron difference, moment analysis, and Drell-Yan pairs are also considered
Inelastic Light Scattering Processes
Fouche, Daniel G.; Chang, Richard K.
1973-01-01
Five different inelastic light scattering processes will be denoted by, ordinary Raman scattering (ORS), resonance Raman scattering (RRS), off-resonance fluorescence (ORF), resonance fluorescence (RF), and broad fluorescence (BF). A distinction between fluorescence (including ORF and RF) and Raman scattering (including ORS and RRS) will be made in terms of the number of intermediate molecular states which contribute significantly to the scattered amplitude, and not in terms of excited state lifetimes or virtual versus real processes. The theory of these processes will be reviewed, including the effects of pressure, laser wavelength, and laser spectral distribution on the scattered intensity. The application of these processes to the remote sensing of atmospheric pollutants will be discussed briefly. It will be pointed out that the poor sensitivity of the ORS technique cannot be increased by going toward resonance without also compromising the advantages it has over the RF technique. Experimental results on inelastic light scattering from I(sub 2) vapor will be presented. As a single longitudinal mode 5145 A argon-ion laser line was tuned away from an I(sub 2) absorption line, the scattering was observed to change from RF to ORF. The basis, of the distinction is the different pressure dependence of the scattered intensity. Nearly three orders of magnitude enhancement of the scattered intensity was measured in going from ORF to RF. Forty-seven overtones were observed and their relative intensities measured. The ORF cross section of I(sub 2) compared to the ORS cross section of N2 was found to be 3 x 10(exp 6), with I(sub 2) at its room temperature vapor pressure.
Energy Technology Data Exchange (ETDEWEB)
Suzuki, A [Tokyo University of Agriculture and Technology, Tokyo (Japan)
1997-11-25
Light concentration characteristics of Fresnel lenses were analyzed by using photometry. Light concentrating systems include a reflective system represented by a rotary parabolic mirror, and a refractive system represented by the Fresnel lens. The refractive system has a focused section broadened as much as the dispersion effect in association with refraction, and cannot derive a focus with high magnification as compared with the reflective system which can achieve it. The refractive system causes reduction in collected light intensity to about half on a parax, hence a large amount of loss. However, the system can be made available inexpensively due to mass production by using mold formation. Although it is difficult to utilize all of the light, 95% of the received radiation is concentrated in an opening area with a radius of about 4G (G is a radius of an image of solar light at a focus plane which passes through the center of a Fresnel lens). The average magnification of light concentration at this time in the opening area reaches 390 times. When a 3-D compound parabolic concentrator (CPC) with a radius of 4G is placed on a lens focus as a secondary light concentrator, the final magnification of light concentration shows a value of about 2700 times, whereas restoration of 39% is possible, as compared with a rotary parabolic mirror. The system has sufficient possibility to be used for high-temperature light concentration. 3 refs., 5 figs., 1 tab.
Experimental Investigation of the Fresnel Drag Effect in RF Coaxial Cables
Directory of Open Access Journals (Sweden)
Brotherton D.
2011-01-01
Full Text Available An experiment that confirms the Fresnel drag formalism in RF coaxial cables is reported. The Fresnel "drag" in bulk dielectrics and in optical fibers has previously been well established. An explanation for this formalism is given, and it is shown that there is no actual drag phenomenon, rather that the Fresnel drag effect is merely the consequence of a simplified description of EM scattering within a dielectric in motion wrt the dynamical 3-space. The Fresnel drag effect plays a critical role in the design of various light-speed anisotropy detectors.
Experimental Investigation of the Fresnel Drag Effect in RF Coaxial Cables
Directory of Open Access Journals (Sweden)
Cahill R. T.
2011-01-01
Full Text Available An experiment that confirms the Fresnel drag formalism in RF coaxial cables is re- ported. The Fresnel ‘drag’ in bulk dielectrics and in optical fibers has previously been well established. An explanation for this formalism is given, and it is shown that there is no actual drag phenomenon, rather that the Fresnel drag effect is merely the conse- quence of a simplified description of EM scattering within a dielectric in motion wrt the dynamical 3-space. The Fresnel drag effect plays a critical role in the design of various light-speed anisotropy detectors.
Inelastic scattering and deformation parameters
International Nuclear Information System (INIS)
Ford, J.L.C. Jr.
1978-01-01
In recent years there has been extensive study of nuclear shape parameters by electron scattering, μ meson atomic transitions, Coulomb excitation and direct nuclear inelastic scattering. Inelastic scattering of strongly absorbed particles, e.g., alpha-particles and heavy ions, at energies below and above the Coulomb barrier probe the charge and mass distributions within the nucleus. This paper summarizes measurements in this field performed at Oak Ridge National Laboratory
International Nuclear Information System (INIS)
Girardi, G.
1980-11-01
In these lectures we attempt to describe the final states of deep inelastic scattering as given by QCD. In the first section we shall briefly comment on the parton model and give the main properties of decay functions which are of interest for the study of semi-inclusive leptoproduction. The second section is devoted to the QCD approach to single hadron leptoproduction. First we recall basic facts on QCD log's and derive after that the evolution equations for the fragmentation functions. For this purpose we make a short detour in e + e - annihilation. The rest of the section is a study of the factorization of long distance effects associated with the initial and final states. We then show how when one includes next to leading QCD corrections one induces factorization breaking and describe the double moments useful for testing such effects. The next section contains a review on the QCD jets in the hadronic final state. We begin by introducing the notion of infrared safe variable and defining a few useful examples. Distributions in these variables are studied to first order in QCD, with some comments on the resummation of logs encountered in higher orders. Finally the last section is a 'gaullimaufry' of jet studies
Nonimaging achromatic shaped Fresnel lenses for ultrahigh solar concentration.
Languy, Fabian; Habraken, Serge
2013-05-15
The maximum concentration ratio achievable with a solar concentrator made of a single refractive primary optics is much more limited by the chromatic aberration than by any other aberration. Therefore achromatic doublets made with poly(methyl methacrylate) and polycarbonate are of great interest to enhance the concentration ratio and to achieve a spectrally uniform flux on the receiver. In this Letter, shaped achromatic Fresnel lenses are investigated. One lossless design is of high interest since it provides spectrally and spatially uniform flux without being affected by soiling problems. With this design an optical concentration ratio of about 8500× can be achieved.
Accounting for Antenna in Half-Space Fresnel Coefficient Estimation
Directory of Open Access Journals (Sweden)
A. D'Alterio
2012-01-01
Full Text Available The problem of retrieving the Fresnel reflection coefficients of a half-space medium starting from measurements collected under a reflection mode multistatic configuration is dealt with. According to our previous results, reflection coefficient estimation is cast as the inversion of linear operator. However, here, we take a step ahead towards more realistic scenarios as the role of antennas (both transmitting and receiving is embodied in the estimation procedure. Numerical results are presented to show the effectiveness of the method for different types of half-space media.
Rainbow and Fresnel diffraction effects in the heavy ion scattering
International Nuclear Information System (INIS)
Salvadori, M.C.B.S.
1984-01-01
A detailed theoretical analysis of the heavy-ion elastic scattering differential cross section, using the uniform semiclassical approximation of Berry in the sharp cut-off limit is presented. A decomposition of the cross section into four physically well-defined components is used in the analysis. The aim of the analysis is to explore the possibility of distinguishing at the cross-section level, between a pure raibow or Fresnel diffraction nature of the heavy-ion elastic scattering at above-barrier energies and not too large angles. (Author) [pt
Weyl Ordering Operator Formula Derived by IWOP Technique and Its Application for Fresnel Operator
International Nuclear Information System (INIS)
Fan Hongyi; Hu Liyun
2009-01-01
Based on the technique of integration within an ordered product of operators, the Weyl ordering operator formula is derived and the Fresnel operators' Weyl ordering is also obtained, which together with the Weyl transformation can immediately lead to Fresnel transformation kernel in classical optics. (general)
Optimum design of nonimaging Fresnel lens; Hiketsuzo fureneru renzu no saiteki sekkei
Energy Technology Data Exchange (ETDEWEB)
Leutz, R.; Komai, K.; Akisawa, A.; Kashiwagi, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan); Suzuki, A. [Unesco, Paris (France). Associations in Japan
1999-11-25
An optimum convex shaped nonimaging Fresnel lens is designed following the edge ray principle. The lens is evaluated by tracing rays and calculating a projective optical concentration ratio. This Fresnel lens can used as concentrator in photovoltaic and solar thermal applications. (author)
Synchrotron radiation focusing by a Bragg--Fresnel lens
International Nuclear Information System (INIS)
Aristov, V.V.; Basov, Y.A.; Snigirev, A.A.
1989-01-01
Since the discovery of x rays and until the present time the possibilities of their controlling and focusing have been widely discussed. In the hard spectrum region (λ∼1 A) the main focusing schemes are the following: geometrical focusing based on incoherent interaction of wave packets reflected by different regions of bending crystals and coherent (dynamic) focusing performed at the cost of the effect of refraction index angular dispersion near the exact Bragg angle value -θ B . A main disadvantage of geometrical focusing is low spatial resolution (∼0.1 mm) and temperature stability. In the case of coherent focusing a main disadvantage is a narrow angular aperture (∼10 sec. of arc) at spatial resolution (∼1--10 μm). Recently, advances in the development of diffraction physics and microstructuring technology open up possibilities for fabricating effective focusing x-ray optical elements---Bragg--Fresnel lenses (BFL)---with high spatial resolution (∼0.1 μm) at a wide angular aperture and high temperature stability. The present paper describes the main principles of Bragg--Fresnel optics (BFO). It presents the results on the synchrotron experiment and on observation of focusing. In this work the peculiarities of BFL diffraction contrast formation are investigated and image transmission using a BFL is performed. Possibilities of developing x-ray optical schemes of ultrahigh resolution on the basis of BFL elements are also discussed
Experimental characterization of Fresnel-Köhler concentrators
Zamora, Pablo; Benítez, Pablo; Mohedano, Rubén; Cvetković, Aleksandra; Vilaplana, Juan; Li, Yang; Hernández, Maikel; Chaves, Julio; Miñano, Juan C.
2012-01-01
Most cost-effective concentrated photovoltaics (CPV) systems are based on an optical train comprising two stages, the first being a Fresnel lens. Among them, the Fresnel-Köhler (FK) concentrator stands out owing to both performance and practical reasons. We describe the experimental measurements procedure for FK concentrator modules. This procedure includes three main types of measurements: electrical efficiency, acceptance angle, and irradiance uniformity at the solar cell plane. We have collected here the performance features of two different FK prototypes (ranging different f-numbers, concentration ratios, and cell sizes). The electrical efficiencies measured in both prototypes are high and fit well with the models, achieving values up to 32.7% (temperature corrected, and with no antireflective coating on SOE or POE surfaces) in the best case. The measured angular transmission curves show large acceptance angles, again perfectly matching the expected values [measured concentration acceptance product (CAP) values over 0.56]. The irradiance pattern on the cell (obtained with a digital camera) shows an almost perfectly uniform distribution, as predicted by raytrace simulations. All these excellent on-sun results confirm the FK concentrator as a potentially cost-effective solution for the CPV market.
Fluorescent sensing with Fresnel microlenses for optofluidic systems
Siudzińska, Anna; Miszczuk, Andrzej; Marczak, Jacek; Komorowska, Katarzyna
2017-05-01
The concept of fluorescent sensing in a microchannel equipped with focusing light Fresnel lenses has been demonstrated. The concept employs a line or array of Fresnel lenses generating a line or array of focused light spots within a microfluidic channel, to increase the sensitivity of fluorescent signal detection in the system. We have presented efficient methods of master mold fabrication based on the lithography method and focused ion beam milling. The flexible microchannel was fabricated by an imprint process with new thiolene-epoxy resin with a good ability to replicate even submicron-size features. For final imprinted lenses, the measured background to peak signal level shows more than nine times the increase in brightness at the center of the focal spot for the green part of the spectrum (532 nm). The effectiveness of the microlenses in fluorescent-marked Escherichia coli bacteria was confirmed in a basic fluoroscope experiment, showing the increase of the sensitivity of the detection by the order of magnitude.
Electron Inelastic-Mean-Free-Path Database
SRD 71 NIST Electron Inelastic-Mean-Free-Path Database (PC database, no charge) This database provides values of electron inelastic mean free paths (IMFPs) for use in quantitative surface analyses by AES and XPS.
Inelastic light scattering in crystals
Sushchinskii, M. M.
The papers presented in this volume are concerned with a variety of problems in optics and solid state physics, such as Raman scattering of light in crystals and disperse media, Rayleigh and inelastic scattering during phase transitions, characteristics of ferroelectrics in relation to the general soft mode concept, and inelastic spectral opalescence. A group-theory approach is used to classify the vibrational spectra of the crystal lattice and to analyze the properties of idealized crystal models. Particular attention is given to surface vibrational states and to the study of the surface layers of crystals and films by light scattering methods.
Development of background reduced Fresnel phase zone plate
International Nuclear Information System (INIS)
Tamari, Yohei; Azechi, Hiroshi
2004-01-01
In study of hot and dense plasma, a high spatial resolution (a few microns) x-ray imaging is very important to observe these plasmas. The Fresnel phase zone plate (FPZP) consists of alternately material and transparent circular annuli placed concentrically, which image x rays using diffraction x rays from all annuli. FPZP have imaged 4.7-4.77 keV x rays with 2.2 μm spatial resolution. However FPZP has a problem that background level is comparable to signal level. In subtraction of background, the error of 10% is caused. For the accurate background subtraction, we designed new FPZP, which consist of three β layers of a transparent zone and two material zones. The new design FPZP parameters (thickness of material zones, each zone width) have been optimized, and in that optimum design signal-to-background ratio is 4 times better than conventional two layers FPZP
Nonimaging fresnel lenses. Design and performance of solar concentrators
Energy Technology Data Exchange (ETDEWEB)
Leutz, R. [Tokyo Univ. of Agriculture and Technology, Koganei-shi (Japan). BASE; Suzuki, A. [UNESCO, Paris (France). Natural Science Sector
2001-07-01
This book offers a detailed and comprehensive account of the engineering of the world's first nonimaging Fresnel lens solar concentrator. The book closes a gap in solar concentrator design, and describes nonimaging refractive optics and its numerical mathematics. The contents follow a systems approach that is absent in standard handbooks of optics or solar energy. The reader is introduced to the principles, theories, and advantages of nonimaging optics from the standpoint of concentrating sunlight (the solar concentrator idea). The book shows the reader how to find his or her own optical solution using the rules and methodologies covering the design and the assessment of the nonimaging lens. This novel solar concentrator is developed within the natural constraints presented by the sun and in relation to competitive solutions offered by other concentrators. (orig.)
A Fresnel collector process heat experiment at Capitol Concrete Products
Hauger, J. S.
1981-01-01
An experiment is planned, conducted and evaluated to determine the feasibility of using a Power Kinetics' Fresnel concentrator to provide process heat in an industrial environment. The plant provides process steam at 50 to 60 psig to two autoclaves for curing masonry blocks. When steam is not required, the plant preheats hot water for later use. A second system is installed at the Jet Propulsion Laboratory parabolic dish test site for hardware validation and experiment control. Experiment design allows for the extrapolation of results to varying demands for steam and hot water, and includes a consideration of some socio-technical factors such as the impact on production scheduling of diurnal variations in energy availability.
Fabrication and characterization of InP fresnel microlenses
International Nuclear Information System (INIS)
Diadiuk, V.; Walpole, J.N.; Liau, Z.L.
1987-01-01
Since diode lasers typically have a beam divergence of a few tens of degrees, collimating the laser outputs leads to greatly far-field patterns, which, in turn translates into more power in the main lobe of the combined output. Achieving this collimation in the case of a diode laser array, with its small device-to-device distance, requires an array of similarly spaced microlenses with very short focal length, small diameter and small F number. In this paper, the authors describe the fabrication and performance of a Fresnel microlens array etched directly in InP wafers; these microlenses have been used successfully to collimate the output of GainAsP/InP buried-heterostructure (BH) diode lasers
Solar-pumped 80 W laser irradiated by a Fresnel lens.
Ohkubo, Tomomasa; Yabe, Takashi; Yoshida, Kunio; Uchida, Shigeaki; Funatsu, Takayuki; Bagheri, Behgol; Oishi, Takehiro; Daito, Kazuya; Ishioka, Manabu; Nakayama, Yuichirou; Yasunaga, Norihito; Kido, Kouichirou; Sato, Yuji; Baasandash, Choijil; Kato, Kiyoshi; Yanagitani, Takagimi; Okamoto, Yoshiaki
2009-01-15
A solar-pumped 100 W class laser that features high efficiency and low cost owing to the use of a Fresnel lens and a chromium codoped neodymium YAG ceramic laser medium was developed. A laser output of about 80 W was achieved with combination of a 4 m(2) Fresnel lens and a pumping cavity as a secondary power concentrator. This output corresponds to 4.3% of conversion efficiency from solar power into laser, and the maximum output from a unit area of Fresnel lens was 20 W/m(2), which is 2.8 times larger than previous results with mirror-type concentrator.
Design and Optimization of Fresnel Lens for High Concentration Photovoltaic System
Directory of Open Access Journals (Sweden)
Lei Jing
2014-01-01
Full Text Available A practical optimization design is proposed, in which the solar direct light spectrum and multijunction cell response range are taken into account in combination, particularly for the Fresnel concentrators with a high concentration and a small aspect ratio. In addition, the change of refractive index due to temperature variation in outdoor operation conditions is also considered in the design stage. The calculation results show that this novel Fresnel lens achieves an enhancement of energy efficiency of about 10% compared with conventional Fresnel lens for a given solar spectrum, solar cell response, and corrected sunshine hours of different ambient temperature intervals.
Active liquid-crystal deflector and lens with Fresnel structure
Shibuya, Giichi; Yamano, Shohei; Yoshida, Hiroyuki; Ozaki, Masanori
2017-02-01
A new type of tunable Fresnel deflector and lens composed of liquid crystal was developed. Combined structure of multiple interdigitated electrodes and the high-resistivity (HR) layer implements the saw-tooth distribution of electrical potential with only the planar surfaces of the transparent substrates. According to the numerical calculation and design, experimental devices were manufactured with the liquid crystal (LC) material sealed into the sandwiched flat glass plates of 0.7 mm thickness with rubbed alignment layers set to an anti-parallel configuration. Fabricated beam deflector with no moving parts shows the maximum tilt angle of +/-1.3 deg which can apply for optical image stabilizer (OIS) of micro camera. We also discussed and verified their lens characteristics to be extended more advanced applications. Transparent interdigitated electrodes were concentrically aligned on the lens aperture with the insulator gaps under their boundary area. The diameter of the lens aperture was 30 mm and the total number of Fresnel zone was 100. Phase retardation of the beam wavefront irradiated from the LC lens device can be evaluated by polarizing microscope images with a monochromatic filter. Radial positions of each observed fringe are plotted and fitted with 2nd degree polynomial approximation. The number of appeared fringes is over 600 in whole lens aperture area and the correlation coefficients of all approximations are over 0.993 that seems enough ideal optical wavefront. The obtained maximum lens powers from the approximations are about +/-4 m-1 which was satisfied both convex and concave lens characteristics; and their practical use for the tunable lens grade eyeglasses became more prospective.
Fast generation of Fresnel holograms based on multirate filtering.
Tsang, Peter; Liu, Jung-Ping; Cheung, Wai-Keung; Poon, Ting-Chung
2009-12-01
One of the major problems in computer-generated holography is the high computation cost involved for the calculation of fringe patterns. Recently, the problem has been addressed by imposing a horizontal parallax only constraint whereby the process can be simplified to the computation of one-dimensional sublines, each representing a scan plane of the object scene. Subsequently the sublines can be expanded to a two-dimensional hologram through multiplication with a reference signal. Furthermore, economical hardware is available with which sublines can be generated in a computationally free manner with high throughput of approximately 100 M pixels/second. Apart from decreasing the computation loading, the sublines can be treated as intermediate data that can be compressed by simply downsampling the number of sublines. Despite these favorable features, the method is suitable only for the generation of white light (rainbow) holograms, and the resolution of the reconstructed image is inferior to the classical Fresnel hologram. We propose to generate holograms from one-dimensional sublines so that the above-mentioned problems can be alleviated. However, such an approach also leads to a substantial increase in computation loading. To overcome this problem we encapsulated the conversion of sublines to holograms as a multirate filtering process and implemented the latter by use of a fast Fourier transform. Evaluation reveals that, for holograms of moderate size, our method is capable of operating 40,000 times faster than the calculation of Fresnel holograms based on the precomputed table lookup method. Although there is no relative vertical parallax between object points at different distance planes, a global vertical parallax is preserved for the object scene as a whole and the reconstructed image can be observed easily.
Solution of a simple inelastic scattering problem
International Nuclear Information System (INIS)
Knudson, S.K.
1975-01-01
Simple examples of elastic scattering, typically from square wells, serve as important pedagogical tools in discussion of the concepts and processes involved in elastic scattering events. An analytic solution of a model inelastic scattering system is presented here to serve in this role for inelastic events. The model and its solution are simple enough to be of pedagogical utility, but also retain enough of the important physical features to include most of the special characteristics of inelastic systems. The specific model chosen is the collision of an atom with a harmonic oscillator, interacting via a repulsive square well potential. Pedagogically important features of inelastic scattering, including its multistate character, convergence behavior, and dependence on an ''inelastic potential'' are emphasized as the solution is determined. Results are presented for various energies and strengths of inelastic scattering, which show that the model is capable of providing an elementary representation of vibrationally inelastic scattering
Evaluation of Fresnel's corrections to the eikonal approximation by the separabilization method
International Nuclear Information System (INIS)
Musakhanov, M.M.; Zubarev, A.L.
1975-01-01
Method of separabilization of potential over the Schroedinger approximate solutions, leading to Schwinger's variational principle for scattering amplitude, is suggested. The results are applied to calculation of the Fresnel corrections to the Glauber approximation
Graphical Approach to Fresnel's Equations for Reflection and Refraction of Light.
Doyle, William T.
1980-01-01
Develops a coordinate-free approach to Fresnel's equations for the reflection and refraction of light at a plane interface. Describes a graphical construction for finding the vector amplitudes of the reflected and transmitted waves. (Author/CS)
Flux-redistribution in the focal region of a planar Fresnel ring mirror
Energy Technology Data Exchange (ETDEWEB)
Sastroamidjojo, M.S.A. (Gadjah Mada Univ., Indonesia); Lubis, W.
1979-01-01
The results of an investigation of flux redistribution at the focal region of a planar Fresnel ring mirror are reported. A parabolic mirror of large aperture was used to provide a parallel beam of light which was directed at the Fresnel test object. A cotton thread grid was used as a mapping aid to provide a 25 x 25 matrix of spatial data points. (SPH)
Quantum correspondence of the mixed Lenz-Fresnel transform in classical optics
International Nuclear Information System (INIS)
Fan Hongyi; Tang Xubing; Lu Hailiang
2006-01-01
We find the quantum correspondence (a four-parameter squeezing operator U(r,s,μ)) of the mixed optical Lenz-Fresnel transform, i.e. that the kernel of Lenz-Fresnel transform is just the matrix element of U(r,s,μ) in the entangled states. The group multiplication rule of U(r,s,μ) is proved by virtue of its coherent entangled state representation which is essential to this correspondence
Interpretation of interfacial structures in X-ray multilayers by TEM Fresnel fringe effects
Nguyen, Tai D.; O'Keefe, Michael A.; Kilaas, Roar; Gronsky, Ronald; Kortright, Jeffrey B.
1991-01-01
Assessment of interfacial structures from high-resolution TEM images of cross-sectional specimens is difficult due to Fresnel fringe effects producing different apparent structures in the images. The effects of these fringes have been commonly over-looked in efforts of making quantitative interpretation of interfacial profiles. In this report, we present the observations of the Fresnel fringes in nanometer period Mo/Si, W/C, and WC/C multilayers in through-focus-series TEM images. Calculation...
Jashnsaz, Hossein; Mohajerani, Ezeddin; Nemati, Hossein; Razavi, Seyed Hossein; Alidokht, Isa Ahmad
2011-06-10
A holographic technique for fabricating an electrically switchable liquid crystal/polymer composite Fresnel lens is reported. A Michelson interferometer is used to produce the required Fresnel pattern, by placing a convex lens into one path of the interferometer. Simplicity of the method and the possibility of fabricating different focal length lenses in a single arrangement are advantages of the method. The performance of the fabricated lens was demonstrated and its electro-optical properties were investigated for its primary focal length.
Polarization transfer in inelastic scattering
International Nuclear Information System (INIS)
Moss, J.M.
1980-01-01
Polarization transfer experiments are now feasible for inelastic scattering experiments on complex nuclei. Experiments thus far have dealt with the spin-flip probability; this observable is sensitive to the action of spin-spin and tensor forces in inelastic scattering. Spin-flip probabilities at E approx. 40 MeV in isoscalar transitions in 12 C(12.71 MeV) and 15 O(8.89 MeV) show considerable deviation from DWBA-shell model predictions; this deviation indicates evidence for more complex reaction mechanisms. Experiments at intermediate energies will soon be possible and will yield data of much higher precision than is possible at lower (E < 100 MeV) energies. These experiments hold exciting promise in such areas as nuclear critical opalescence. 7 figures, 1 table
Inelastic neutron scattering from clusters
International Nuclear Information System (INIS)
Gudel, H.U.
1985-01-01
Magnetic excitations in clusters of paramagnetic ions have non-vanishing cross-sections for inelastic neutron scattering (INS). Exchange splittings can be determined, the temperature dependence of exchange can be studied, intra- and intercluster effects can be separated and magnetic form factors determined. INS provides a more direct access to the molecular properties than bulk techniques. Its application is restricted to complexes with no or few (< 10%) hydrogen atoms
International Nuclear Information System (INIS)
Kraemer, M.; Steegborn, J.; Zerwas, P.M.
1994-11-01
Inelastic photoproduction of J/ψ particles at high energies is one of the processes to determine the gluon distribution in the nucleon. We have calculated the QCD radiative corrections to the color-singlet model of this reaction. They are large at moderate photon energies, but decrease with increasing energies. The cross section and the J/ψ energy spectrum are compared with the available fixed-target photoproduction data and predictions are given for the HERA energy range. (orig.)
Static Linear Fresnel Lenses as LCPV System in a Greenhouse
Sonneveld, P. J.; Swinkels, G. L. A. M.; van Tuijl, B. A. J.; Janssen, H. J. J.; de Zwart, H. F.
2011-12-01
A low concentrating PV system with water cooling (LCPVT system) will result in electrical and thermal energy output from the solar energy excess entering a building or greenhouse. All the direct radiation could be converted, which corresponds to 75% of the incoming solar energy. This will significantly reduce the demand of cooling of the building. For an optimal performance it is beneficial to construct asymmetric roof elements with a steep inclination at the north side (the exact angle of course depends on the latitude of the building site). The Fresnel lens structure is oriented in upwards direction. In the current design, two of them are placed between an AR-coated double glass structure to prevent pollution and condensation on the lenses. Compared with a previous system, the number of lenses is reduced from 3 to 2 lenses, which reduces the costs of the system by limiting the number of receivers. By the upward facing of the lens structure, the focus quality is preserved over a much broader range of angles of incidence compared to a lens with downward facing structures. Each PMMA lens with a size of 1.20 m×1.60 m is composed of 12 `tiles' for easy production. The focal distance of the lens is 1,875 m and the concentration factor 50x. In most cases the focus line is thinner than 3 cm and the transmission is above 80%. The performance of these lenses with respect of the shape of the focal area and the position of the focal line has been analyzed with ray tracing techniques. From this analyses it was concluded that tracking of the receiver module is possible with two motors. One motor controls the distance between lens and receiver and one motor controls the translocation of the receivers parallel to the lens. The second conclusion was that the positions of the focal line are within the bounds of the greenhouse construction for almost the whole year. Only in winter, the focal line will be unreachable from time to time. A 480 m2 greenhouse with the LCPVT system
High precision refractometry based on Fresnel diffraction from phase plates.
Tavassoly, M Taghi; Naraghi, Roxana Rezvani; Nahal, Arashmid; Hassani, Khosrow
2012-05-01
When a transparent plane-parallel plate is illuminated at a boundary region by a monochromatic parallel beam of light, Fresnel diffraction occurs because of the abrupt change in phase imposed by the finite change in refractive index at the plate boundary. The visibility of the diffraction fringes varies periodically with changes in incident angle. The visibility period depends on the plate thickness and the refractive indices of the plate and the surrounding medium. Plotting the phase change versus incident angle or counting the visibility repetition in an incident-angle interval provides, for a given plate thickness, the refractive index of the plate very accurately. It is shown here that the refractive index of a plate can be determined without knowing the plate thickness. Therefore, the technique can be utilized for measuring plate thickness with high precision. In addition, by installing a plate with known refractive index in a rectangular cell filled with a liquid and following the described procedures, the refractive index of the liquid is obtained. The technique is applied to measure the refractive indices of a glass slide, distilled water, and ethanol. The potential and merits of the technique are also discussed.
Numerical Study of Concentration Characteristics of Linear Fresnel Reflector System
International Nuclear Information System (INIS)
Lee, Hyun Jin; Kim, Jong Kyu; Lee, Sang Nam
2015-01-01
In this study, we numerically investigated the concentration characteristics of a linear Fresnel reflector system that can drive a solar thermal absorption refrigeration system to be installed in Saudi Arabia. Using an optical modeling program based on the Monte Carlo ray-tracing method, we simulated the concentrated solar flux, concentration efficiency, and concentrated solar energy on four representative days of the year - the vernal equinox, summer solstice, autumnal equinox, and winter solstice. Except the winter solstice, the concentrations were approximately steady from 9 AM to 15 PM, and the concentration efficiencies exceed 70%. Moreover, the maximum solar flux around the solar receiver center changes only within the range of 13.0 - 14.6 kW/m 2 . When we investigated the effects of the receiver installation height, reflector width, and reflector gap, the optimal receiver installation height was found to be 5 m. A smaller reflector width had a greater concentration efficiency. However, the design of the reflector width should be based on the capacity of the refrigeration system because it dominantly affects the concentrated solar energy. The present study was an essential prerequisite for thermal analyses of the solar receiver. Thus, an optical-thermal integration study in the future will assist with the performance prediction and design of the entire system
Numerical Study of Concentration Characteristics of Linear Fresnel Reflector System
Energy Technology Data Exchange (ETDEWEB)
Lee, Hyun Jin [Kookmin Univ., Seoul (Korea, Republic of); Kim, Jong Kyu; Lee, Sang Nam [Korea Institute of Energy Research, Daejeon (Korea, Republic of)
2015-12-15
In this study, we numerically investigated the concentration characteristics of a linear Fresnel reflector system that can drive a solar thermal absorption refrigeration system to be installed in Saudi Arabia. Using an optical modeling program based on the Monte Carlo ray-tracing method, we simulated the concentrated solar flux, concentration efficiency, and concentrated solar energy on four representative days of the year - the vernal equinox, summer solstice, autumnal equinox, and winter solstice. Except the winter solstice, the concentrations were approximately steady from 9 AM to 15 PM, and the concentration efficiencies exceed 70%. Moreover, the maximum solar flux around the solar receiver center changes only within the range of 13.0 - 14.6 kW/m{sup 2}. When we investigated the effects of the receiver installation height, reflector width, and reflector gap, the optimal receiver installation height was found to be 5 m. A smaller reflector width had a greater concentration efficiency. However, the design of the reflector width should be based on the capacity of the refrigeration system because it dominantly affects the concentrated solar energy. The present study was an essential prerequisite for thermal analyses of the solar receiver. Thus, an optical-thermal integration study in the future will assist with the performance prediction and design of the entire system.
Thin Fresnel zone plate lenses for focusing underwater sound
International Nuclear Information System (INIS)
Calvo, David C.; Thangawng, Abel L.; Nicholas, Michael; Layman, Christopher N.
2015-01-01
A Fresnel zone plate (FZP) lens of the Soret type creates a focus by constructive interference of waves diffracted through open annular zones in an opaque screen. For underwater sound below MHz frequencies, a large FZP that blocks sound using high-impedance, dense materials would have practical disadvantages. We experimentally and numerically investigate an alternative approach of creating a FZP with thin (0.4λ) acoustically opaque zones made of soft silicone rubber foam attached to a thin (0.1λ) transparent rubber substrate. An ultra-thin (0.0068λ) FZP that achieves higher gain is also proposed and simulated which uses low-volume fraction, bubble-like resonant air ring cavities to construct opaque zones. Laboratory measurements at 200 kHz indicate that the rubber foam can be accurately modeled as a lossy fluid with an acoustic impedance approximately 1/10 that of water. Measured focal gains up to 20 dB agree with theoretical predictions for normal and oblique incidence. The measured focal radius of 0.68λ (peak-to-null) agrees with the Rayleigh diffraction limit prediction of 0.61 λ/NA (NA = 0.88) for a low-aberration lens
The Fresnel Diffraction: A Story of Light and Darkness
Aime, C.; Aristidi, É.; Rabbia, Y.
2013-03-01
In a first part of the paper we give a simple introduction to the free space propagation of light at the level of a Master degree in Physics. The presentation promotes linear filtering aspects at the expense of fundamental physics. Following the Huygens-Fresnel approach, the propagation of the wave writes as a convolution relationship, the impulse response being a quadratic phase factor. We give the corresponding filter in the Fourier plane. As an illustration, we describe the propagation of wave with a spatial sinusoidal amplitude, introduce lenses as quadratic phase transmissions, discuss their Fourier transform properties and give some properties of Soret screens. Classical diffractions of rectangular diaphragms are also given here. In a second part of the paper, the presentation turns into the use of external occulters in coronagraphy for the detection of exoplanets and the study of the solar corona. Making use of Lommel series expansions, we obtain the analytical expression for the diffraction of a circular opaque screen, giving thereby the complete formalism for the Arago-Poisson spot. We include there shaped occulters. The paper ends up with a brief application to incoherent imaging in astronomy.
An Electron-Beam Profile Monitor Using Fresnel Zone Plates
International Nuclear Information System (INIS)
Nakamura, Norio; Sakai, Hiroshi; Iida, Kensuke; Shinoe, Kenji; Takaki, Hiroyuki; Fujisawa, Masami; Hayano, Hitoshi; Muto, Toshiya; Nomura, Masaharu; Kamiya, Yukihide; Koseki, Tadashi; Amemiya, Yoshiyuki; Aoki, Nobutada; Nakayama, Koichi
2004-01-01
We have developed a beam profile monitor using two Fresnel zone plates (FZPs) at the KEK-ATF (Accelerator Test Facility) damping ring to measure small electron-beam sizes for low-emittance synchrotron radiation sources. The monitor has a structure of an X-ray microscope, where two FZPs constitute an X-ray imaging optics. In the monitor system, the synchrotron radiation from the electron beam at the bending magnet is monochromatized to 3.235-keV X-rays by a crystal monochromator and the transverse electron-beam image is twenty-times magnified by the two FZPs and detected on an X-ray CCD camera. This monitor has the following advantages: (1) high spatial resolution, (2) non-destructive measurement, (3) real-time monitoring, and (4) direct electron-beam imaging. With the beam profile monitor, we have succeeded in obtaining a clear electron-beam image and measuring the extremely small beam size less than 10 μm. The measured magnification of the imaging optics was in good agreement with the design value
Deep inelastic processes and the parton model
International Nuclear Information System (INIS)
Altarelli, G.
The lecture was intended as an elementary introduction to the physics of deep inelastic phenomena from the point of view of theory. General formulae and facts concerning inclusive deep inelastic processes in the form: l+N→l'+hadrons (electroproduction, neutrino scattering) are first recalled. The deep inelastic annihilation e + e - →hadrons is then envisaged. The light cone approach, the parton model and their relation are mainly emphasized
Deep inelastic electron and muon scattering
International Nuclear Information System (INIS)
Taylor, R.E.
1975-07-01
From the review of deep inelastic electron and muon scattering it is concluded that the puzzle of deep inelastic scattering versus annihilation was replaced with the challenge of the new particles, that the evidence for the simplest quark-algebra models of deep inelastic processes is weaker than a year ago. Definite evidence of scale breaking was found but the specific form of that scale breaking is difficult to extract from the data. 59 references
Use of inelastic analysis in cask design
International Nuclear Information System (INIS)
Ammerman, Douglas J.; Breivik, Nicole L.
2000-01-01
In this paper, the advantages and disadvantages of inelastic analysis are discussed. Example calculations and designs showing the implications and significance of factors affecting inelastic analysis are given. From the results described in this paper it can be seen that inelastic analysis provides an improved method for the design of casks. It can also be seen that additional code and standards work is needed to give designers guidance in the use of inelastic analysis. Development of these codes and standards is an area where there is a definite need for additional work. The authors hope that this paper will help to define the areas where that need is most acute
Elastic and inelastic psi production by muons
International Nuclear Information System (INIS)
Loken, S.C.
1981-06-01
Results are presented on the elastic and inelastic production of psi (3.1). The elastic data are qualitative agreement with the predictions of photon-gluon fusion but have a steeper dependence on Q 2 than the model predicts. A QCD calculation accounts well for the shape of the inelastic data in inelasticity, Q 2 and E/sub γ/, but fails to account for the absolute cross section. At 209 GeV, the cross-section for elastic psi production is 0.36 +- 0.07 nb; for inelastic, 0.28 +- 0.06nb
Topics in deep inelastic scattering
International Nuclear Information System (INIS)
Wandzura, S.M.
1977-01-01
Several topics in deep inelastic lepton--nucleon scattering are discussed, with emphasis on the structure functions appearing in polarized experiments. The major results are: infinite set of new sum rules reducing the number of independent spin dependent structure functions (for electroproduction) from two to one; the application of the techniques of Nachtmann to extract the coefficients appearing in the Wilson operator product expansion; and radiative corrections to the Wilson coefficients of free field theory. Also discussed are the use of dimensional regularization to simplify the calculation of these radiative corrections
Inelastic scattering from amorphous solids
International Nuclear Information System (INIS)
Price, D.L.
1985-08-01
The potential of inelastic neutron scattering techniques for surveying various aspects of the dynamics of amorphous solids is briefly reviewed. The recent use of the Intense Pulsed Neutron Source to provide detailed information on the optical vibrations of glasses is discussed in more detail. The density of states represents an averaged quantity which gives information about the general characteristics of the structure and bonding. More extensive information can be obtained by studying the detailed wavevector dependence of the dynamic structure factor. 15 refs., 7 figs
International Nuclear Information System (INIS)
Kraemer, M.
1995-04-01
Inelastic photoproduction of J/ψ particles at high energies is one of the processes to determine the gluon distribution in the nucleon. The QCD radiative corrections to the color-singlet model of this reaction have recently been calculated. They are large at moderate photon energies, but decrease with increasing energies. I compare the cross section and the J/ψ energy spectrum with the available fixed-target photoproduction data. Predictions for the HERA energy range are given which demonstrate the sensitivity of the result to the parametrization of the gluon distribution in the small-x region. (orig.)
Frabboni, Stefano; Gazzadi, Gian Carlo; Grillo, Vincenzo; Pozzi, Giulio
2015-07-01
Modern nanotechnology tools allowed us to prepare slits of 90 nm width and 450 nm spacing in a screen almost completely opaque to 200 keV electrons. Then by covering both slits with a layer of amorphous material and carrying out the experiment in a conventional transmission electron microscope equipped with an energy filter we can demonstrate that the diffraction pattern, taken by selecting the elastically scattered electrons, shows the presence of interference fringes, but with a bimodal envelope which can be accounted for by taking into account the non-constant thickness of the deposited layer. However, the intensity of the inelastically scattered electrons in the diffraction plane is very broad and at the limit of detectability. Therefore the experiment was repeated using an aluminum film and a microscope also equipped with a Schottky field emission gun. It was thus possible to observe also the image due to the inelastically scattered electron, which does not show interference phenomena both in the Fraunhofer or Fresnel regimes. If we assume that inelastic scattering through the thin layer covering the slits provides the dissipative process of interaction responsible for the localization mechanism, then these experiments can be considered a variant of the Feynman which-way thought experiment. Copyright © 2015 Elsevier B.V. All rights reserved.
Energy Technology Data Exchange (ETDEWEB)
Hoogenboom, J.E. (Technische Hogeschool Delft (Netherlands))
1983-01-01
From the collision mechanics of inelastic discrete-level scattering several properties are derived for the secondary-neutron energy distribution (SNED) for inelastic continuum scattering, when conceived as scattering with continuously-distributed inelastic levels. Using assumptions about the level density and neutron cross section the SNED can be calculated and some examples are shown. A formula is derived to calculate from a given inelastic continuum SNED a function, which is proportional to the level density and the neutron cross section. From this relation further conditions follow for the SNED. Representations for the inelastic continuum SNED currently in use do not, in general, satisfy most of the derived conditions.
International Nuclear Information System (INIS)
Hoogenboom, J.E.
1983-01-01
From the collision mechanics of inelastic discrete-level scattering several properties are derived for the secondary-neutron energy distribution (SNED) for inelastic continuum scattering, when conceived as scattering with continuously-distributed inelastic levels. Using assumptions about the level density and neutron cross section the SNED can be calculated and some examples are shown. A formula is derived to calculate from a given inelastic continuum SNED a function, which is proportional to the level density and the neutron cross section. From this relation further conditions follow for the SNED. Representations for the inelastic continuum SNED currently in use do not, in general, satisfy most of the derived conditions. (author)
Comparison of Fresnel zone plates and uniformly redundant arrays
International Nuclear Information System (INIS)
Fenimore, E.E.; Cannon, T.M.; Miller, E.L.
1978-01-01
Several imaging systems in laser fusion, e-beam fusion, and astronomy employ a Fresnel zone plate (FZP) as a coded aperture. The recent development of uniformly redundant arrays (URAs) promises several improvements in these systems. The first advantage of the URA is the fact that its modulation transfer function (MTF) is the same as the MTF of a single pinhole, whereas the MTF of an FZP is an erratic function including some small values. This means that if inverse filtering is used, the URA will be less susceptible to noise. If a correlation analysis is used, the FZP will produce artifacts whereas the URA has no artifacts (assuming planar sources). Both the FZP and URA originated from functions which had flat MTFs. However, practical considerations in the implementation of the FZP detracted from its good characteristics whereas the URA was only mildly affected. The second advantage of the URA is that it better utilizes the available detector area. With the FZP, the aperture should be smaller than the detector in order to maintain the full angular resolution corresponding to the thinnest zone. The cyclic nature of the URA allows one to mosaic it in such a way that the entire detector area collects photons from all of the sources within the field of view while maintaining the full angular resolution. If the FZP is as large (or larger) than the detector, all parts of the source will not be resolved with the same resolution. The FZP does have some advantages, in particular its radial symmetry eases the alignment problem; it has a convenient optical decoding method; and higher diffraction order reconstruction might provide better spatial resolution
Earthquake response of inelastic structures
International Nuclear Information System (INIS)
Parulekar, Y.M.; Vaity, K.N.; Reddy, .R.; Vaze, K.K.; Kushwaha, H.S.
2004-01-01
The most commonly used method in the seismic analysis of structures is the response spectrum method. For seismic re-evaluation of existing facilities elastic response spectrum method cannot be used directly as large deformation above yield may be observed under Safe Shutdown Earthquake (SSE). The plastic deformation, i.e. hysteretic characteristics of various elements of the structure cause dissipation of energy. Hence the values of damping given by the code, which does not account hysteretic energy dissipation cannot be directly used. In this paper, appropriate damping values are evaluated for 5-storey, 10-storey and 15-storey shear beam structures, which deform beyond their yield limit. Linear elastic analysis is performed for the same structures using these damping values and the storey forces are compared with those obtained using inelastic time history analysis. A damping model, which relates ductility of the structure and damping, is developed. Using his damping model, a practical structure is analysed and results are compared with inelastic time history analysis and the comparison is found to be good
Zhao, Yuchen; Zemmamouche, Redouane; Vandenrijt, Jean-François; Georges, Marc P.
2018-05-01
A combination of digital holographic interferometry (DHI) and digital speckle photography (DSP) allows in-plane and out-of-plane displacement measurement between two states of an object. The former can be determined by correlating the two speckle patterns whereas the latter is given by the phase difference obtained from DHI. We show that the amplitude of numerically reconstructed object wavefront obtained from Fresnel in-line digital holography (DH), in combination with phase shifting techniques, can be used as speckle patterns in DSP. The accuracy of in-plane measurement is improved after correcting the phase errors induced by reference wave during reconstruction process. Furthermore, unlike conventional imaging system, Fresnel DH offers the possibility to resize the pixel size of speckle patterns situated on the reconstruction plane under the same optical configuration simply by zero-padding the hologram. The flexibility of speckle size adjustment in Fresnel DH ensures the accuracy of estimation result using DSP.
A space Fresnel imager concept assessment study led by CNES for astrophysical applications
Hinglais, Emmanuel
2011-06-01
In 2009, the Centre National d'Etudes Spatiales (CNES) carried out an assessment study on a "Fresnel telescope" concept based on a two-spacecraftformation flying configuration. This concept uses a binary Fresnel zone plate, and the principle of diffraction focusing, which allows high resolution optical imaging for astrophysics. In addition to CNES, the Laboratoire d'Astrophysique de Toulouse Tarbes (LATT) was deeply involved at two levels: through Research & Technology (R&T) studies to simulate and validate on a test bench the Fresnel concept performance, and through active participation in the CNES team for the optical aspects and to define the astrophysical fields of Fresnel-based space missions. The study was conducted within the technical limitations that resulted from a compromise between the R&T state of the art and the potential scientific domains of interest. The main technical limitations are linked to the size of the primary Fresnel array and to its usable spectral bandwidth. In this framework, the study covers ambitious architectures, correlating the technology readiness of the main critical components with the time-scale and programmatic horizons. The possible scientific topics arise from this range of missions. In this paper, I present a mission launched by a Soyuz, dedicated to astrophysics in the Ultra Violet (UV) band: 120 to 300 nm using a 4-m Fresnel array. It could be competitive in the next fifteen years, whereas a 10-m aperture mission in different bands; UV, visible or Infra Red (IR) (up to 6 μm) could be achievable in the future. Larger missions, using a primary array larger than 20 m, request technologies not yet available but that will probably be based on new inflatable structures with membranes, as already tested in the USA for other ends.
Chen, Hang; Liu, Zhengjun; Chen, Qi; Blondel, Walter; Varis, Pierre
2018-05-01
In this letter, what we believe is a new technique for optical color image encryption by using Fresnel diffraction and a phase modulation in an extended fractional Fourier transform domain is proposed. Different from the RGB component separation based method, the color image is converted into one component by improved Chirikov mapping. The encryption system is addressed with Fresnel diffraction and phase modulation. A pair of lenses is placed into the fractional Fourier transform system for the modulation of beam propagation. The structure parameters of the optical system and parameters in Chirikov mapping serve as extra keys. Some numerical simulations are given to test the validity of the proposed cryptosystem.
Design and fabrication of Si-HDPE hybrid Fresnel lenses for infrared imaging systems.
Manaf, Ahmad Rosli Abdul; Sugiyama, Tsunetoshi; Yan, Jiwang
2017-01-23
In this work, novel hybrid Fresnel lenses for infrared (IR) optical applications were designed and fabricated. The Fresnel structures were replicated from an ultraprecision diamond-turned aluminum mold to an extremely thin layer (tens of microns) of high-density polyethylene polymer, which was directly bonded onto a flat single-crystal silicon wafer by press molding without using adhesives. Night mode imaging results showed that the fabricated lenses were able to visualize objects in dark fields with acceptable image quality. The capability of the lenses for thermography imaging was also demonstrated. This research provides a cost-effective method for fabricating ultrathin IR optical components.
Component and prototype panel testing of the mini-dome Fresnel lens photovoltaic concentrator array
Piszczor, Michael F.; Swartz, Clifford K.; O'Neill, Mark J.
1990-01-01
The mini-dome Fresnel lens concentrator array, a high-efficiency, lightweight space photovoltaic array concept, is described. The three critical elements of the array concept are the Fresnel lens concentrator, the prismatic cell power cover, and the photovoltaic cell. Prototype concentrator lenses have been fabricated and tested, with optical efficiencies reaching 90 percent. Work is progressing on the design and fabrication of the panel structure. The impact of recent advances in 30 percent-efficient multijunction photovoltaic cells on array performance is also discussed. Near-term performance goals of 300 w/sq m and 100 w/kg are now feasible.
Fresnel Lens Solar Concentrator Design Based on Geometric Optics and Blackbody Radiation Equations
Watson, Michael D.; Jayroe, Robert, Jr.
1999-01-01
Fresnel lenses have been used for years as solar concentrators in a variety of applications. Several variables effect the final design of these lenses including: lens diameter, image spot distance from the lens, and bandwidth focused in the image spot. Defining the image spot as the geometrical optics circle of least confusion and applying blackbody radiation equations the spot energy distribution can be determined. These equations are used to design a fresnel lens to produce maximum flux for a given spot size, lens diameter, and image distance. This approach results in significant increases in solar efficiency over traditional single wavelength designs.
Starke, R.; Schober, G. A. H.
2018-03-01
We provide a systematic theoretical, experimental, and historical critique of the standard derivation of Fresnel's equations, which shows in particular that these well-established equations actually contradict the traditional, macroscopic approach to electrodynamics in media. Subsequently, we give a rederivation of Fresnel's equations which is exclusively based on the microscopic Maxwell equations and hence in accordance with modern first-principles materials physics. In particular, as a main outcome of this analysis being of a more general interest, we propose the most general boundary conditions on electric and magnetic fields which are valid on the microscopic level.
Deep inelastic scattering and disquarks
International Nuclear Information System (INIS)
Anselmino, M.
1993-01-01
The most comprehensive and detailed analyses of the existing data on the structure function F 2 (x, Q 2 ) of free nucleons, from the deep inelastic scattering (DIS) of charged leptons on hydrogen and deuterium targets, have proved beyond any doubt that higher twist, 1/Q 2 corrections are needed in order to obtain a perfect agreement between perturbative QCD predictions and the data. These higher twist corrections take into account two quark correlations inside the nucleon; it is then natural to try to model them in the quark-diquark model of the proton. In so doing all interactions between the two quarks inside the diquark, both perturbative and non perturbative, are supposed to be taken into account. (orig./HSI)
Jets in deep inelastic scattering
International Nuclear Information System (INIS)
Joensson, L.
1995-01-01
Jet production in deep inelastic scattering provides a basis for the investigation of various phenomena related to QCD. Two-jet production at large Q 2 has been studied and the distributions with respect to the partonic scaling variables have been compared to models and to next to leading order calculations. The first observations of azimuthal asymmetries of jets produced in first order α s processes have been obtained. The gluon initiated boson-gluon fusion process permits a direct determination of the gluon density of the proton from an analysis of the jets produced in the hard scattering process. A comparison of these results with those from indirect extractions of the gluon density provides an important test of QCD. (author)
Development of multilayer Fresnel lens (zone plate) for formation of focused neutron beam
International Nuclear Information System (INIS)
Tamura, Shigeharu
2008-01-01
Multilayer Fresnel zone plates (FZPs) for the neutron beamline have been designed and fabricated. Firstly, materials for the FZP were examined: layer materials, wire substrate, etc. Secondly, FZPs were designed and three kinds of FZPs were fabricated: two Cu/Al-FZPs and a Ni(Cr)/Al-FZP. (author)
High convergence efficiency design of flat Fresnel lens with large aperture
Ke, Jieyao; Zhao, Changming; Guan, Zhe
2018-01-01
This paper designed a circle-shaped Fresnel lens with large aperture as part of the solar pumped laser design project. The Fresnel lens designed in this paper simulate in size 1000mm×1000mm, focus length 1200mm and polymethyl methacrylate (PMMA) material in order to conduct high convergence efficiency. In the light of design requirement of concentric ring with same width of 0.3mm, this paper proposed an optimized Fresnel lens design based on previous sphere design and conduct light tracing simulation in Matlab. This paper also analyzed the effect of light spot size, light intensity distribution, optical efficiency under four conditions, monochromatic parallel light, parallel spectrum light, divergent monochromatic light and sunlight. Design by 550nm wavelength and under the condition of Fresnel reflection, the results indicated that the designed lens could convergent sunlight in diffraction limit of 11.8mm with a 78.7% optical efficiency, better than the sphere cutting design results of 30.4%.
A fast point-cloud computing method based on spatial symmetry of Fresnel field
Wang, Xiangxiang; Zhang, Kai; Shen, Chuan; Zhu, Wenliang; Wei, Sui
2017-10-01
Aiming at the great challenge for Computer Generated Hologram (CGH) duo to the production of high spatial-bandwidth product (SBP) is required in the real-time holographic video display systems. The paper is based on point-cloud method and it takes advantage of the propagating reversibility of Fresnel diffraction in the propagating direction and the fringe pattern of a point source, known as Gabor zone plate has spatial symmetry, so it can be used as a basis for fast calculation of diffraction field in CGH. A fast Fresnel CGH method based on the novel look-up table (N-LUT) method is proposed, the principle fringe patterns (PFPs) at the virtual plane is pre-calculated by the acceleration algorithm and be stored. Secondly, the Fresnel diffraction fringe pattern at dummy plane can be obtained. Finally, the Fresnel propagation from dummy plan to hologram plane. The simulation experiments and optical experiments based on Liquid Crystal On Silicon (LCOS) is setup to demonstrate the validity of the proposed method under the premise of ensuring the quality of 3D reconstruction the method proposed in the paper can be applied to shorten the computational time and improve computational efficiency.
Zhang, Xiaolei; Zhang, Xiangchao; Yuan, He; Zhang, Hao; Xu, Min
2018-02-01
Digital holography is a promising measurement method in the fields of bio-medicine and micro-electronics. But the captured images of digital holography are severely polluted by the speckle noise because of optical scattering and diffraction. Via analyzing the properties of Fresnel diffraction and the topographies of micro-structures, a novel reconstruction method based on the dual-tree complex wavelet transform (DT-CWT) is proposed. This algorithm is shiftinvariant and capable of obtaining sparse representations for the diffracted signals of salient features, thus it is well suited for multiresolution processing of the interferometric holograms of directional morphologies. An explicit representation of orthogonal Fresnel DT-CWT bases and a specific filtering method are developed. This method can effectively remove the speckle noise without destroying the salient features. Finally, the proposed reconstruction method is compared with the conventional Fresnel diffraction integration and Fresnel wavelet transform with compressive sensing methods to validate its remarkable superiority on the aspects of topography reconstruction and speckle removal.
LED Uniform Illumination Using Double Linear Fresnel Lenses for Energy Saving
Directory of Open Access Journals (Sweden)
Ngoc Hai Vu
2017-12-01
Full Text Available We present a linear Fresnel lens design for light-emitting diode (LED uniform illumination applications. The LED source is an array of LEDs. An array of collimating lens is applied to collimate output from the LED array. Two linear Fresnel lenses are used to redistribute the collimated beam along two dimensions in the illumination area. Collimating lens and linear Fresnel lens surfaces are calculated by geometrical optics and nonimaging optics. The collimated beam output from the collimating lens array is divided into many fragments. Each fragment is refracted by a segment of Fresnel lens and distributed over the illumination area, so that the total beam can be distributed to the illumination target uniformly. The simulation results show that this design has a compact structure, high optical efficiency of 82% and good uniformity of 76.9%. Some consideration of the energy savings and optical performance are discussed by comparison with other typical light sources. The results show that our proposed LED lighting system can reduce energy consumption five-times in comparison to using a conventional fluorescent lamp. Our research is a strong candidate for low cost, energy savings for indoor and outdoor lighting applications.
Design of a segmented nonimaging Fresnel dome for nontracking solar collection
Viera-González, Perla M.; Sánchez-Guerrero, Guillermo E.; Martínez-Guerra, Edgar; Ceballos-Herrera, Daniel E.
2017-07-01
The efficiency of sunlight collection systems is related to the optical element used as a collector. On this subject, the design of a nontracking solar collector that consists of a segmented nonimaging Fresnel dome is presented. It is formed by the conjunction of different zones for solar collection, where each one is a nonimaging Fresnel lens that collects a specific angular range (θ) of sunlight received in the northeast of Mexico, but the methodology presented can be easily extended to other geographic locations. The final design is a semistationary segmented collector with a 100-cm diameter and 50-cm focal length that needs a 180-deg rotation over the XY-plane in each equinox. The numerical simulations show that the nontracking segmented collector has a combined acceptance semiangle of θ=±105 deg with an average efficiency of over 67% from 9:00 to 18:00 h. The spatial and angular distributions of the sunlight collected are also included. This design has a collection area equal to that of a single nonimaging Fresnel lens with an acceptance semiangle of θ=±45 deg. These results are reproducible and provide valuable data for designing nontracking solar collectors based on nonimaging Fresnel lens.
Optical sectioning using a digital Fresnel incoherent-holography-based confocal imaging system
Kelner, Roy; Katz, Barak; Rosen, Joseph
2015-01-01
We propose a new type of confocal microscope using Fresnel incoherent correlation holography (FINCH). Presented here is a confocal configuration of FINCH using a phase pinhole and point illumination that is able to suppress out-of-focus information from the recorded hologram and hence combine the super-resolution capabilities of FINCH with the sectioning capabilities of confocal microscopy. PMID:26413560
Optical sectioning using a digital Fresnel incoherent-holography-based confocal imaging system
Kelner, Roy; Katz, Barak; Rosen, Joseph
2014-01-01
We propose a new type of confocal microscope using Fresnel incoherent correlation holography (FINCH). Presented here is a confocal configuration of FINCH using a phase pinhole and point illumination that is able to suppress out-of-focus information from the recorded hologram and hence combine the super-resolution capabilities of FINCH with the sectioning capabilities of confocal microscopy.
24-GHz LTCC Fractal Antenna Array SoP With Integrated Fresnel Lens
Ghaffar, Farhan A.; Khalid, Muhammad Umair; Salama, Khaled N.; Shamim, Atif
2012-01-01
A novel 24-GHz mixed low-temperature co-fired ceramic (LTCC) tape based system-on-package (SoP) is presented, which incorporates a fractal antenna array with an integrated grooved Fresnel lens. The four-element fractal array employs a relatively low
Huygens-Feynman-Fresnel principle as the basis of applied optics.
Gitin, Andrey V
2013-11-01
The main relationships of wave optics are derived from a combination of the Huygens-Fresnel principle and the Feynman integral over all paths. The stationary-phase approximation of the wave relations gives the correspondent relations from the point of view of geometrical optics.
Fresnel Lenses fabricated by femtosecond laser micromachining on Polymer 1D Photonic Crystal
Directory of Open Access Journals (Sweden)
Guduru Surya S.K.
2013-11-01
Full Text Available We report the fabrication of micro Fresnel lenses by femtosecond laser surface ablation on polymer 1D photonic crystals. This device is designed to focus the transmitted wavelength of the photonic crystal and filter the wavelengths corresponding to the photonic band gap region. Integration of such devices in a wavelength selective light harvesting and filtering microchip can be achieved.
Energy Technology Data Exchange (ETDEWEB)
Grisenti, R.E.
2000-06-01
In this thesis experimental results on the diffraction of rare gas atoms (He, Ne, Ar, Kr) and molecular (D{sub 2}) beams by a 100 nm period transmission grating and on the focusing of a helium atom beam through a Fresnel zone plate have been reported. (orig.)
A concentrator system for BI-CPVT with static linear Fresnel lenses
Swinkels, G.L.A.M.; Sonneveld, P.J.; Tuijl, van B.A.J.; Janssen, H.J.J.; Zwart, de H.F.
2011-01-01
A greenhouse with Fresnel lenses in the south facing roof and a receiver for concentrated Photovoltaic with water cooling (CPVT system) will result in electrical and thermal energy output from the solar energy excess entering a greenhouse. The PV system converts about half of the direct radiation
Inelastic scattering of fast electrons by crystals
International Nuclear Information System (INIS)
Allen, L.J.; Josefsson, T.W.
1995-01-01
Generalized fundamental equations for electron diffraction in crystals, which include the effect of inelastic scattering described by a nonlocal interaction, are derived. An expression is obtained for the cross section for any specific type of inelastic scattering (e.g. inner-shell ionization, Rutherford backscattering). This result takes into account all other (background) inelastic scattering in the crystal leading to absorption from the dynamical Bragg-reflected beams, in practice mainly due to thermal diffuse scattering. There is a contribution to the cross section from all absorbed electrons, which form a diffuse background, as well as from the dynamical electrons. The approximations involved, assuming that the interactions leading to inelastic scattering can be described by a local potential are discussed, together with the corresponding expression for the cross section. It is demonstrated by means of an example for K-shell electron energy loss spectroscopy that nonlocal effects can be significant. 47 refs., 4 figs
Elastic and inelastic heavy ion scattering
International Nuclear Information System (INIS)
Toepffer, C.; University of the Witwatersrand, Johannesburg; Richter, A.
1977-02-01
In the field of elastic and inelastic heavy ion scattering, the following issues are dealt with: semiclassical descriptive approximations, optical potentials, barriers, critical radii and angular momenta, excitation functions and the application to superheavy ions and high energies. (WL) [de
Photon diffractive dissociation in deep inelastic scattering
International Nuclear Information System (INIS)
Ryskin, M.G.
1990-01-01
The new ep-collider HERA gives us the possibility to study the diffractive dissociation of virtual photon in deep inelastic ep-collision. The process of photon dissociation in deep inelastic scattering is the most direct way to measure the value of triple-pomeron vertex G 3P . It was shown that the value of the correct bare vertex G 3P may more than 4 times exceeds its effective value measuring in the triple-reggeon region and reaches the value of about 40-50% of the elastic pp-pomeron vertex. On the contrary in deep inelastic processes the perpendicular momenta q t of the secondary particles are large enough. Thus in deep inelastic reactions one can measure the absolute value of G 3P vertex in the most direct way and compare its value and q t dependence with the leading log QCD predictions
Mean associative multiplicities in deep inelastic processes
International Nuclear Information System (INIS)
Dzhaparidze, G.Sh.; Kiselev, A.V.; Petrov, V.A.
1981-01-01
The associative hadron multiplicities in deep inelastic and Drell--Yan processes are studied. In particular the mean multiplicities in different hard processes in QCD are found to be determined by the mean multiplicity in parton jet [ru
Multiplicity distributions in inelastic reactions on nuclei
Caneschi, L; Schwimmer, A
1976-01-01
The multiplicity distribution of the number of knocked-out nucleons and the correlation of the former with the multiplicity of the produced mesons, in inelastic particle-nucleus scattering, are computed.
Leading particle in deep inelastic scattering
International Nuclear Information System (INIS)
Petrov, V.A.
1984-01-01
The leading particle effect in deep inelastic scattering is considered. The change of the characteris cs shape of the leading particle inclusive spectrum with Q 2 is estimated to be rather significant at very high Q 2
International Nuclear Information System (INIS)
Feng, Chaoqing; Zheng, Hongfei; Wang, Rui; Ma, Xinglong
2016-01-01
Highlights: • A common design method of a cycloidal transmissive Fresnel solar concentrator was presented. • The gallium arsenide high concentrated solar was used as the receiver. • High efficiency of electric generating could be achieved at noon. • Fresnel solar concentrator was studied and compared in hazy weather and clear weather. - Abstract: A design method of a cycloidal transmissive Fresnel solar concentrator which can provide a certain width focal line was presented in this study. Based on the optical principle of refraction, the dimensions of each wedge-shaped element of Fresnel lens are calculated. An optical simulation has been done to obtain the optical efficiency of the concentrator for different tracking error and axial incidence angle. It has been found that about 80% of the incident sunlight can still be gathered by the absorber when the tracking error is within 0.7°. When the axial angle of incidence is within 10°, it almost has no influence to the receiving rate. The concentrating photovoltaic/thermal system with transmissive Fresnel solar concentrator has been designed in this paper. Take the gallium arsenide high concentrated battery as the receiver, experimental research about cylindrical Fresnel concentrating photovoltaic/thermal system is undertaken in the real sky. Main parameters are tested such as the temperature distribution on receiver, electric energy and thermal energy outputs of concentrating photovoltaic/thermal system, the efficiency of multipurpose utilization of electric and heat, and so on. The test results in clear weather show that maximum electric generating efficiency is about 18% at noon, the maximum heat receiving rate of cooling water is about 45%. At noon time (11:00–13:00), the total efficiency of thermal and electricity can reach more than 55%. Performance of this concentrating photovoltaic/thermal system with transmissive Fresnel solar concentrator is studied and compared in two types typical weather, hazy
Deep inelastic inclusive weak and electromagnetic interactions
International Nuclear Information System (INIS)
Adler, S.L.
1976-01-01
The theory of deep inelastic inclusive interactions is reviewed, emphasizing applications to electromagnetic and weak charged current processes. The following reactions are considered: e + N → e + X, ν + N → μ - + X, anti ν + N → μ + + X where X denotes a summation over all final state hadrons and the ν's are muon neutrinos. After a discussion of scaling, the quark-parton model is invoked to explain the principle experimental features of deep inelastic inclusive reactions
Finite element analysis of inelastic structural behavior
International Nuclear Information System (INIS)
Argyris, J.H.; Szimmat, J.; Willam, K.J.
1977-01-01
The paper describes recent achievements in the finite element analysis of inelastic material behavior. The main purpose is to examine the interaction of three disciplines; (i) the finite element formulation of large deformation problems in the light of a systematic linearization, (ii) the constitutive modelling of inelastic processes in the rate-dependent and rate-independent response regime and (iii) the numerical solution of nonlinear rate problems via incremental iteration techniques. In the first part, alternative finite element models are developed for the idealization of large deformation problems. A systematic approach is presented to linearize the field equations locally by an incremental procedure. The finite element formulation is then examined for the description of inelastic material processes. In the second part, nonlinear and inelastic material phenomena are classified and illustrated with representative examples of concrete and metal components. In particular, rate-dependent and rate-independent material behavior is examined and representative constitutive models are assessed for their mathematical characterization. Hypoelastic, elastoplastic and endochronic models are compared for the description rate-independent material phenomena. In the third part, the numerial solution of inelastic structural behavior is discussed. In this context, several incremental techniques are developed and compared for tracing the evolution of the inelastic process. The numerical procedures are examined with regard to stability and accuracy to assess the overall efficiency. The 'optimal' incremental technique is then contrasted with the computer storage requirements to retain the data for the 'memory-characteristics' of the constitutive model
Elastic/Inelastic Measurement Project
International Nuclear Information System (INIS)
Yates, Steven; Hicks, Sally; Vanhoy, Jeffrey; McEllistrem, Marcus
2015-12-01
The work scope involves the measurement of neutron scattering from natural sodium ( 23 Na) and two isotopes of iron, 56 Fe and 54 Fe. Angular distributions, i.e., differential cross sections, of the scattered neutrons will be measured for 5 to 10 incident neutron energies per year. The work of the first year concentrates on 23 Na, while the enriched iron samples are procured. Differential neutron scattering cross sections provide information to guide nuclear reaction model calculations in the low-@@energy (few MeV) fast-@@neutron region. This region lies just above the isolated resonance region, which in general is well studied; however, model calculations are difficult in this region because overlapping resonance structure is evident and direct nuclear reactions are becoming important. The standard optical model treatment exhibits good predictive ability for the wide-@@region average cross sections but cannot treat the overlapping resonance features. In addition, models that do predict the direct reaction component must be guided by measurements to describe correctly the strength of the direct component, e.g., @@ 2 must be known to describe the direct component of the scattering to the first excited state. Measurements of the elastic scattering differential cross sections guide the optical model calculations, while inelastic differential cross sections provide the crucial information for correctly describing the direct component. Activities occurring during the performance period are described.
Elastic/Inelastic Measurement Project
Energy Technology Data Exchange (ETDEWEB)
Yates, Steven [Univ. of Kentucky, Lexington, KY (United States); Hicks, Sally [Univ. of Dallas, TX (United States); Vanhoy, Jeffrey [U.S. Naval Academy, Annapolis, MD (United States); McEllistrem, Marcus [Univ. of Kentucky, Lexington, KY (United States)
2016-03-01
The work scope involves the measurement of neutron scattering from natural sodium (^{23}Na) and two isotopes of iron, ^{56}Fe and ^{54}Fe. Angular distributions, i.e., differential cross sections, of the scattered neutrons will be measured for 5 to 10 incident neutron energies per year. The work of the first year concentrates on ^{23}Na, while the enriched iron samples are procured. Differential neutron scattering cross sections provide information to guide nuclear reaction model calculations in the low-energy (few MeV) fast-neutron region. This region lies just above the isolated resonance region, which in general is well studied; however, model calculations are difficult in this region because overlapping resonance structure is evident and direct nuclear reactions are becoming important. The standard optical model treatment exhibits good predictive ability for the wide-region average cross sections but cannot treat the overlapping resonance features. In addition, models that do predict the direct reaction component must be guided by measurements to describe correctly the strength of the direct component, e.g., β_{2} must be known to describe the direct component of the scattering to the first excited state. Measurements of the elastic scattering differential cross sections guide the optical model calculations, while inelastic differential cross sections provide the crucial information for correctly describing the direct component. Activities occurring during the performance period are described.
Languy, Fabian; Habraken, Serge
2011-07-15
Solar concentrators made of a single refractive primary optics are limited to a concentration ratio of about 1000× [Opt. Express 19, A280 (2011)], due only to longitudinal chromatic aberration, while mirrors are limited to ∼46,000× by the angular size of the Sun. To reduce the chromatic aberration while keeping cost-effective systems for concentrated photovoltaics, a study of four different kinds of flat Fresnel doublets made of polycarbonates and polymethyl methacrylate is presented. It reveals that Fresnel doublets may have fewer optical losses than non-Fresnel doublets, with a lower lateral chromatic split allowing for even higher concentration ratio. © 2011 Optical Society of America
Siegel, Nisan; Rosen, Joseph; Brooker, Gary
2013-10-01
Recent advances in Fresnel incoherent correlation holography (FINCH) increase the signal-to-noise ratio in hologram recording by interference of images from two diffractive lenses with focal lengths close to the image plane. Holograms requiring short reconstruction distances are created that reconstruct poorly with existing Fresnel propagation methods. Here we show a dramatic improvement in reconstructed fluorescent images when a 2D Hamming window function substituted for the disk window typically used to bound the impulse response in the Fresnel propagation. Greatly improved image contrast and quality are shown for simulated and experimentally determined FINCH holograms using a 2D Hamming window without significant loss in lateral or axial resolution.
Comparison of elastic and inelastic analyses
International Nuclear Information System (INIS)
Ammerman, D.J.; Heinstein, M.W.; Wellman, G.W.
1992-01-01
The use of inelastic analysis methods instead of the traditional elastic analysis methods in the design of radioactive material (RAM) transport packagings leads to a better understanding of the response of the package to mechanical loadings. Thus, better assessment of the containment, thermal protection, and shielding integrity of the package after a structure accident event can be made. A more accurate prediction of the package response can lead to enhanced safety and also allow for a more efficient use of materials, possibly leading to a package with higher capacity or lower weight. This paper discusses the advantages and disadvantages of using inelastic analysis in the design of RAM shipping packages. The use of inelastic analysis presents several problems to the package designer. When using inelastic analysis the entire nonlinear response of the material must be known, including the effects of temperature changes and strain rate. Another problem is that there currently is not an acceptance criteria for this type of analysis that is approved by regulatory agencies. Inelastic analysis acceptance criteria based on failure stress, failure strain , or plastic energy density could be developed. For both elastic and inelastic analyses it is also important to include other sources of stress in the analyses, such as fabrication stresses, thermal stresses, stresses from bolt preloading, and contact stresses at material interfaces. Offsetting these added difficulties is the improved knowledge of the package behavior. This allows for incorporation of a more uniform margin of safety, which can result in weight savings and a higher level of confidence in the post-accident configuration of the package. In this paper, comparisons between elastic and inelastic analyses are made for a simple ring structure and for a package to transport a large quantity of RAM by rail (rail cask) with lead gamma shielding to illustrate the differences in the two analysis techniques
Implications of stress range for inelastic analysis
International Nuclear Information System (INIS)
Karabin, M.E.; Dhalla, A.K.
1981-01-01
The elastic stress range over a complete load cycle is routinely used to formulate simplified rules regarding the inelastic behavior of structures operating at elevated temperature. For example, a 300 series stainless steel structure operating at elevated temperature, in all probability, would satisfy the ASME Boiler and Pressure Vessel Code criteria if the linearized elastic stress range is less than three times the material yield strength. However, at higher elastic stress ranges it is difficult to judge, a priori, that a structural component would comply with inelastic Code criteria after a detailed inelastic analysis. The purpose of this paper is to illustrate that it is not the elastic stress range but the stress intensities at specific times during a thermal transient which provide a better insight into the inelastic response of the structure. The specific example of the CRBRP flued head design demonstrates that the temperature differential between various parts of the structure can be changed by modifying the insulation pattern and heat flow path in the structure, without significantly altering the elastic stress range over a complete load cycle. However, the modified design did reduce the stress intensity during steady state elevated temperature operation. This modified design satisfied the inelastic Code criteria whereas the initial design failed to comply with the strain accumulation criterion
Stop grating for perfect replication of micro Fresnel lens by thermal imprinting
International Nuclear Information System (INIS)
Gao, Yulong; Lin, Jie; Jin, Peng; Tan, Jiubin; Davies, Graham; Prewett, Philip D
2012-01-01
A stop grating concept is proposed to improve polymer filling in the thermal imprinting of a micro Fresnel lens structure. The stop grating consists of line and space structures outside the Fresnel lens pattern zone area. The experimental results have proved that the stop grating can help to achieve the complete filling of a mold, at the same time acting as a stop to prevent possible damage to the mold surface relief structures during imprinting press. A computer simulation was carried out to identify the phenomena of micro-holes at the edge of imprinted pattern. By removing the cavity between the pattern area and stop grating, perfect imprinting results have been achieved. (paper)
Song, Jinghui; Yuan, Hui; Xia, Yunfeng; Kan, Weimin; Deng, Xiaowen; Liu, Shi; Liang, Wanlong; Deng, Jianhua
2018-03-01
This paper introduces the working principle and system constitution of the linear Fresnel solar lithium bromide absorption refrigeration cycle, and elaborates several typical structures of absorption refrigeration cycle, including single-effect, two-stage cycle and double-effect lithium bromide absorption refrigeration cycle A 1.n effect absorption chiller system based on the best parameters was introduced and applied to a linear Fresnel solar absorption chiller system. Through the field refrigerator performance test, the results show: Based on this heat cycle design and processing 1.n lithium bromide absorption refrigeration power up to 35.2KW, It can meet the theoretical expectations and has good flexibility and reliability, provides guidance for the use of solar thermal energy.
Sub-100 nm hard X-ray microbeam generation with Fresnel zone plate optics
Takano, H; Takeuchi, A
2003-01-01
A hard X-ray focusing test of a Fresnel zone plate has been performed with a synchrotron radiation source at the undulator beamline 20XU of SPring-8. Fresnel zone plate with a radius of 150 mu m, and an outermost zone width of 100 nm was used for the X-ray focusing device. The 248-m-long beamline provides fully coherent illumination for the focusing device. The focused beam evaluated by the knife-edge-scan method and scanning microscope test using test charts. Nearly diffraction- limited focusing with a size of 120 nm was achieved for the first-order diffraction at 10 keV X-ray. Evaluation for the third order diffraction was also performed at 8 keV X-ray, and a focal size of 50 m has been obtained. (author)
Um experimento simples usado na produção de placas de zonas de Fresnel
Muller,Márcia; Silva,Jean Carlos Cardozo da; Fabris,José Luís
2005-01-01
Neste trabalho propomos um experimento simples que tem por finalidade auxiliar no aprendizado dos fenômenos de interferência e difração da luz. Após uma análise pertinente da teoria de Fresnel da difração, os conhecimentos são aplicados na compreensão do funcionamento das placas de zonas de Fresnel. Apresentamos uma descrição detalhada dos processos usados para a fabricação e caracterização destas placas zonais, o que possibilita a produção de lentes difrativas com a distância focal desejada ...
Characterization of a photovoltaic-thermal module for Fresnel linear concentrator
International Nuclear Information System (INIS)
Chemisana, D.; Ibanez, M.; Rosell, J.I.
2011-01-01
Highlights: → A combined domed Fresnel lens - CPC PVT system is designed and characterized. → Electrical and thermal experiments have been performed. → CFD analysis has been used to determine thermal characteristic dimensionless numbers. - Abstract: An advanced solar unit is designed to match the needs of building integration and concentrating photovoltaic/thermal generation. The unit proposed accurately combines three elements: a domed linear Fresnel lens as primary concentrator, a compound parabolic reflector as secondary concentrator and a photovoltaic-thermal module. In this work the photovoltaic-thermal generator is built, analysed and characterized. Models for the electrical and thermal behaviour of the module are developed and validated experimentally. Applying a thermal resistances approach the results from both models are combined. Finally, efficiency electrical and thermal curves are derived from theoretical analysis showing good agreement with experimental measurements.
A perfect Fresnel acoustic reflector implemented by a Fano-resonant metascreen
Amin, M.
2018-04-10
We propose a perfectly reflecting acoustic metasurface which is designed by replacing the curved segments of the traditional Fresnel reflector by flat Fano-resonant sub-wavelength unit cells. To preserve the original Fresnel focusing mechanism, the unit cell phase follows a specific phase profile which is obtained by applying the generalized Snell\\'s law and Fermat\\'s principle. The reflected curved phase fronts are thus created at the air-metasurface boundary by tailoring the metasurface dispersion as dictated by Huygens\\' principle. Since the unit cells are implemented by sub-wavelength double slit-shaped cavity resonators, the impinging sound waves are perfectly reflected producing acoustic focusing with negligible absorption. We use plane-wave solution and full-wave simulations to demonstrate the focusing effects. The simulation results closely follow the analytical predictions.
Diffraction patterns in Fresnel approximation of periodic objects for a colorimeter of two apertures
Cortes-Reynoso, Jose-German R.; Suarez-Romero, Jose G.; Hurtado-Ramos, Juan B.; Tepichin-Rodriguez, Eduardo; Solorio-Leyva, Juan Carlos
2004-10-01
In this work, we present a study of Fresnel diffraction of periodic structures in an optical system of two apertures. This system of two apertures was used successfully for measuring color in textile samples solving the problems of illumination and directionality that present current commercial equipments. However, the system is sensible to the spatial frequency of the periodic sample"s area enclosed in its optical field of view. The study of Fresnel diffraction allows us to establish criteria for geometrical parameters of measurements in order to assure invariance in angular rotations and spatial positions. In this work, we use the theory of partial coherence to calculate the diffraction through two continuous apertures. In the calculation process, we use the concept of point-spread function of the system for partial coherence, in this way we avoid complicated statistical processes commonly used in the partial coherence theory.
Development of a Fresnel lens for cold neutrons based on neutron refractive optics
International Nuclear Information System (INIS)
Oku, T.; Morita, S.; Moriyasu, S.; Yamagata, Y.; Ohmori, H.; Takizawa, Y.; Shimizu, H.M.; Hirota, T.; Kiyanagi, Y.; Ino, T.; Furusaka, M.; Suzuki, J.
2001-01-01
We have developed compound refractive lenses (CRLs) for cold neutrons, which are made of vitreous silica and have an effective potential of (90.1-2.7x10 -4 i) neV. In the case of compound refractive optics, neutron absorption by the material deteriorates lens performance. Thus, to prevent an increase in neutron absorption with increasing beam size, we have developed Fresnel lenses using the electrolytic in-process dressing grinding technique. The lens characteristics were carefully investigated with experimental and numerical simulation studies. The lenses functioned as a neutron focusing lens, and the focal length of 14 m was obtained with a 44-element series of the Fresnel lenses for 10 A neutrons. Moreover, good neutron transmission of 0.65 for 15 A neutrons was obtained due to the shape effect. According to comprehensive analysis of the obtained results, it is possible to realize a CRL for practical use by choosing a suitable lens shape and material
A perfect Fresnel acoustic reflector implemented by a Fano-resonant metascreen
Amin, M.; Siddiqui, O.; Farhat, Mohamed; Khelif, A.
2018-01-01
We propose a perfectly reflecting acoustic metasurface which is designed by replacing the curved segments of the traditional Fresnel reflector by flat Fano-resonant sub-wavelength unit cells. To preserve the original Fresnel focusing mechanism, the unit cell phase follows a specific phase profile which is obtained by applying the generalized Snell's law and Fermat's principle. The reflected curved phase fronts are thus created at the air-metasurface boundary by tailoring the metasurface dispersion as dictated by Huygens' principle. Since the unit cells are implemented by sub-wavelength double slit-shaped cavity resonators, the impinging sound waves are perfectly reflected producing acoustic focusing with negligible absorption. We use plane-wave solution and full-wave simulations to demonstrate the focusing effects. The simulation results closely follow the analytical predictions.
International Nuclear Information System (INIS)
Yamada, Yoshifumi; Liu, Na; Ito, Satoshi
2006-01-01
The signal in the Fresnel transform technique corresponds to a blurred one of the spin density image. Because the amplitudes of adjacent sampled signals have a high interrelation, the signal amplitude at a point between sampled points can be estimated with a high degree of accuracy even if the sampling is so coarse as to generate aliasing in the reconstructed images. In this report, we describe a new aliasless image reconstruction technique in the phase scrambling Fourier transform (PSFT) imaging technique in which the PSFT signals are converted to Fresnel transform signals by multiplying them by a quadratic phase term and are then interpolated using polynomial expressions to generate fully encoded signals. Numerical simulation using MR images showed that almost completely aliasless images are reconstructed by this technique. Experiments using ultra-low-field PSFT MRI were conducted, and aliasless images were reconstructed from coarsely sampled PSFT signals. (author)
Analytical analysis of solar thermal collector with glass and Fresnel lens glazing
Zulkifle, Idris; Ruslan, Mohd Hafidz Hj; Othman, Mohd Yusof Hj; Ibarahim, Zahari
2018-04-01
Solar thermal collector is a system that converts solar radiation to heat. The heat will raise the temperature higher than the ambient temperature. Absorber and glazing are two important components in order to increase the temperature of the collector. The thermal absorber will release heat by convection and as radiation to the surrounding. These losses will be reduced by glazing. Other than that, glazing is beneficial for protecting the collector from dust and water. This study discusses about modelling of solar thermal collector effects of different mass flow rates with different glazing for V-groove flat plate solar collectors. The glazing used was the glass and linear Fresnel lens. Concentration ratio in this modelling was 1.3 for 0.1m solar collector thickness. Results show that solar collectors with linear Fresnel lens has the highest efficiency value of 71.18% compared to solar collectors with glass which has efficiency 54.10% with same operation conditions.
International Nuclear Information System (INIS)
Shiina, Tatsuo; Suzuki, Tsuyoshi; Honda, Toshio; Ito, Atsushi; Kinjo, Yasuhito; Yoshimura, Hideyuki; Yada, Keiji; Shinohara, Kunio
2009-01-01
In soft X-ray projection microscopy, it is easy to alter the magnification by changing the distance between the pinhole and the specimen, while the image is blurred because the soft X-rays are diffracted through the propagation from specimen to CCD detector. We corrected the blurred image by the iteration procedure of Fresnel to inverse Fresnel transformation taking phase distribution of the specimen into account. The experiments were conducted at the BL-11A of the Photon Factory, KEK, Japan for the specimens such as glass-capillaries, latex-particles, dried mammalian cells and human chromosomes. Many of those blurred images were corrected adequately by the iteration procedure, though some images such as those which have high-contrast or are overlapped by small cells still remain to be improved.
A perfect Fresnel acoustic reflector implemented by a Fano-resonant metascreen
Amin, M.; Siddiqui, O.; Farhat, M.; Khelif, A.
2018-04-01
We propose a perfectly reflecting acoustic metasurface which is designed by replacing the curved segments of the traditional Fresnel reflector by flat Fano-resonant sub-wavelength unit cells. To preserve the original Fresnel focusing mechanism, the unit cell phase follows a specific phase profile which is obtained by applying the generalized Snell's law and Fermat's principle. The reflected curved phase fronts are thus created at the air-metasurface boundary by tailoring the metasurface dispersion as dictated by Huygens' principle. Since the unit cells are implemented by sub-wavelength double slit-shaped cavity resonators, the impinging sound waves are perfectly reflected producing acoustic focusing with negligible absorption. We use plane-wave solution and full-wave simulations to demonstrate the focusing effects. The simulation results closely follow the analytical predictions.
The Cosmology of Composite Inelastic Dark Matter
Energy Technology Data Exchange (ETDEWEB)
Spier Moreira Alves, Daniele; Behbahani, Siavosh R.; /SLAC /Stanford U., ITP; Schuster, Philip; Wacker, Jay G.; /SLAC
2011-08-19
Composite dark matter is a natural setting for implementing inelastic dark matter - the O(100 keV) mass splitting arises from spin-spin interactions of constituent fermions. In models where the constituents are charged under an axial U(1) gauge symmetry that also couples to the Standard Model quarks, dark matter scatters inelastically off Standard Model nuclei and can explain the DAMA/LIBRA annual modulation signal. This article describes the early Universe cosmology of a minimal implementation of a composite inelastic dark matter model where the dark matter is a meson composed of a light and a heavy quark. The synthesis of the constituent quarks into dark hadrons results in several qualitatively different configurations of the resulting dark matter composition depending on the relative mass scales in the system.
Inelastic instruments at the ISIS facility
International Nuclear Information System (INIS)
Taylor, A.D.
1988-01-01
This summarises the status of the inelastic spectrometers at the ISIS facility and gives some highlights from their scientific programme. The inelastic spectrometers HET, TFXA and IRIS are now being used routinely by UK and International research groups and have produced notable scientific results. Work has progressed steadily on eVS. The PRISMA spectrometer, the product of a collaboration between CNR, Italy and RAL, was installed this summer. Earlier this year an agreement was reached in principle between the Rutherford Appleton Laboratory and the University of Wurzburg (West Germany) to build a second spectrometer (ROTAX) for the study of coherent inelastic excitations. A more sophisticated technical concept than that of PRISMA, based on a nonuniformly rotating analyser, it will allow a greater flexibility in the choice of dynamic scans. Substantial progress has also been made on the design of MARI, the sister spectrometer to HET, which is being built as part of the UK-Japan collaboration on pulsed neutron scattering. (author)
Thyroid scintigraphy using coded apertures derived from a complex Fresnel zone plate
International Nuclear Information System (INIS)
Meinke, J.
1986-01-01
Comparative evaluations of conventional scintiscanning and Fresnel zone plate imaging carried out in the thyroid for the purposes of this study showed that the purported benefits of the latter technique were confirmed by phantoms but did to a lesser extent bear out in patients. Major drawbacks are the lack of additional information of clinical relevance, the greater length of time needed and the difficult interpretation of artefacts. (TRV) [de
Fresnel's original interpretation of complex numbers in 19th century optics
DEFF Research Database (Denmark)
Avelar Sotomaior Karam, Ricardo
2018-01-01
In 1823, Fresnel published an original (physical) interpretation of complex numbers in his investigations of refraction and reflection of polarized light. This is arguably the first time that complex numbers were given a physical interpretation, which led to a better understanding of elliptical a...... and circular polarizations. This rather unknown episode of the history of physics is described in this work, and some of the pedagogical lessons that can be extracted from it are discussed....
Fresnel's original interpretation of complex numbers in 19th century optics
Karam, Ricardo
2018-04-01
In 1823, Fresnel published an original (physical) interpretation of complex numbers in his investigations of refraction and reflection of polarized light. This is arguably the first time that complex numbers were given a physical interpretation, which led to a better understanding of elliptical and circular polarizations. This rather unknown episode of the history of physics is described in this work, and some of the pedagogical lessons that can be extracted from it are discussed.
Hincapie, Diego; Velasquez, Daniel; Garcia-Sucerquia, Jorge
2017-12-15
In this Letter, we present a method for chromatic compensation in numerical reconstruction of digitally recorded holograms based on Fresnel-Bluestein propagation. The proposed technique is applied to correct the chromatic aberration that arises in the reconstruction of RGB holograms of both millimeter- and micrometer-sized objects. The results show the feasibility of this strategy to remove the wavelength dependence of the size of the numerically propagated wavefields.
Fresnel zone plate imaging of a 252Cf spontaneous fission source
International Nuclear Information System (INIS)
Stalker, K.T.; Hessel, K.R.
1976-11-01
The feasibility of coded aperture imaging for nuclear fuel motion monitoring is shown using Cf 252 spontaneous fission source. The theory of coded aperture imaging for Fresnel zone plate apertures is presented and design considerations for zone plate construction are discussed. Actual images are obtained which demonstrate a transverse resolution of 1.7 mm and a tomographic resolution of 1.5 millimeters. The capability of obtaining images through 12.7 mm of stainless steel is also shown
Inelastic electron holography: First results with surface plasmons
Energy Technology Data Exchange (ETDEWEB)
Falk, Roeder; Hannes, Lichte [Triebenberg Labor, Institute for Structure Physics, TU Dresden, 01062 Dresden (Germany)
2011-07-01
Inelastic interaction and wave optics seem to be incompatible in that inelastic processes destroy coherence, which is the fundamental requirement for holography. In special experiments it is shown that energy transfer larger than some undoubtedly destroys coherence of the inelastic electron with the elastic remainder. Consequently, the usual inelastic processes, such as phonon-, plasmon- or inner shell-excitations with energy transfer of several out to several, certainly produce incoherence with the elastic ones. However, it turned out that within the inelastic wave, *newborn* by the inelastic process, there is a sufficiently wide area of coherence for generating *inelastic holograms*. This is exploited to create holograms with electrons scattered at surface-plasmons, which opens up quantum mechanical investigation of these inelastic processes.
Inelastic analysis methods for piping systems
International Nuclear Information System (INIS)
Boyle, J.T.; Spence, J.
1980-01-01
The analysis of pipework systems which operate in an environment where local inelastic strains are evident is one of the most demanding problems facing the stress analyst in the nuclear field. The spatial complexity of even the most modest system makes a detailed analysis using finite element techniques beyond the scope of current computer technology. For this reason the emphasis has been on simplified methods. It is the aim of this paper to provide a reasonably complete, state-of-the-art review of inelastic pipework analysis methods and to attempt to highlight areas where reliable information is lacking and further work is needed. (orig.)
Inelastic neutron scattering from glass formers
International Nuclear Information System (INIS)
Buchenau, U.
1997-01-01
Neutron spectra below and above the glass transition temperature show a pronounced difference between strong and fragile glass formers in Angell's fragility scheme. The strong anharmonic increase of the inelastic scattering with increasing temperature in fragile substances is absent in the strongest glass former SiO 2 . That difference is reflected in the temperature dependence of Brillouin sound velocities above the glass transition. Coherent inelastic neutron scattering data indicate a mixture of sound waves and local modes at the low frequency boson peak. A relation between the fragility and the temperature dependence of the transverse hypersound velocity at the glass temperature is derived. (author)
Gamma-rays from deep inelastic collisions
International Nuclear Information System (INIS)
Stephens, F.S.
1979-01-01
The γ-rays associated with deep inelastic collisions can give information about the magnitude and orientation of the angular momentum transferred in these events. In this review, special emphasis is placed on understanding the origin and nature of these γ-rays in order to avoid some of the ambiguities that can arise. The experimental information coming from these γ-ray studies is reviewed, and compared briefly with that obtained by other methods and also with the expectations from current models for deep inelastic collisions. 15 figures
Nuclear structure in deep-inelastic reactions
International Nuclear Information System (INIS)
Rehm, K.E.
1986-01-01
The paper concentrates on recent deep inelastic experiments conducted at Argonne National Laboratory and the nuclear structure effects evident in reactions between super heavy nuclei. Experiments indicate that these reactions evolve gradually from simple transfer processes which have been studied extensively for lighter nuclei such as 16 O, suggesting a theoretical approach connecting the one-step DWBA theory to the multistep statistical models of nuclear reactions. This transition between quasi-elastic and deep inelastic reactions is achieved by a simple random walk model. Some typical examples of nuclear structure effects are shown. 24 refs., 9 figs
Electrically Tunable Binary-Phase Fresnel Lens Based on Polymer Dispersed Liquid Crystal
Directory of Open Access Journals (Sweden)
Hui LI
2017-08-01
Full Text Available This is a proposal for a Fresnel lens with an electrically tunable binary-phase made of polymer dispersed liquid crystal (PDLC, which has relatively fast response time and low applied voltage. Simple fabrication is the major advantage of the proposed method. In this study, NOA65 and E7 were utilized with weight ratios of 60 wt.%: 40 wt.%. There was also the utilization of a relatively low intensity UV-light, 0.53 mW/cm2. The duration time of exposure was about 30 hours. The performance improvement of the Fresnel lens resulted from the infiltration of large LC droplet into the PDLC film. The phenomenon of black cross strip patterns could be explained with the use of the electro-hydrodynamics theory. The diffraction efficiency of the proposed lens was from 31.1 % to 41 % with the changes of externally applied voltage. This work presents an effective approach to get relatively complete phase separation in PDLC. The proposed method also provides great potential in developing high performance Fresnel lens.DOI: http://dx.doi.org/10.5755/j01.ms.23.2.16317
Diamond turning of small Fresnel lens array in single crystal InSb
International Nuclear Information System (INIS)
Jasinevicius, R G; Duduch, J G; Cirino, G A; Pizani, P S
2013-01-01
A small Fresnel lens array was diamond turned in a single crystal (0 0 1) InSb wafer using a half-radius negative rake angle (−25°) single-point diamond tool. The machined array consisted of three concave Fresnel lenses cut under different machining sequences. The Fresnel lens profiles were designed to operate in the paraxial domain having a quadratic phase distribution. The sample was examined by scanning electron microscopy and an optical profilometer. Optical profilometry was also used to measure the surface roughness of the machined surface. Ductile ribbon-like chips were observed on the cutting tool rake face. No signs of cutting edge wear was observed on the diamond tool. The machined surface presented an amorphous phase probed by micro Raman spectroscopy. A successful heat treatment of annealing was carried out to recover the crystalline phase on the machined surface. The results indicated that it is possible to perform a ‘mechanical lithography’ process in single crystal semiconductors. (paper)
Mechanical Energy Changes in Perfectly Inelastic Collisions
Mungan, Carl E.
2013-01-01
Suppose a block of mass "m"[subscript 1] traveling at speed "v"[subscript 1] makes a one-dimensional perfectly inelastic collision with another block of mass "m"[subscript 2]. What else does one need to know to calculate the fraction of the mechanical energy that is dissipated in the collision? (Contains 1 figure.)
Parity violation in deep inelastic scattering
Energy Technology Data Exchange (ETDEWEB)
Souder, P. [Syracuse Univ., NY (United States)
1994-04-01
AA beam of polarized electrons at CEBAF with an energy of 8 GeV or more will be useful for performing precision measurements of parity violation in deep inelastic scattering. Possible applications include precision tests of the Standard Model, model-independent measurements of parton distribution functions, and studies of quark correlations.
Some applications of polarized inelastic neutron scattering
Indian Academy of Sciences (India)
A brief account of applications of polarized inelastic neutron scattering in condensed matter research is given. ... the itinerant antiferromagnet chromium we demonstrate that the dynamics of the longitudinal and transverse excitations are very different, resolving a long standing puzzle concerning the slope of their dispersion.
Developments in inelastic instrumentation at ISIS
International Nuclear Information System (INIS)
Taylor, A.D.; Bowden, Z.A.; Carlile, C.J.
1989-01-01
The authors summarize developments on the three scheduled inelastic spectrometers HET, TFXA and IRIS and illustrate their scientific program with some recent highlights. They give details of commissioning experiments on PRISMA and discuss the status of the eVS and polarization programs. The status of the MARI project is reviewed. 15 refs., 22 figs
Particle Production in Deep Inelastic Muon Scattering
Energy Technology Data Exchange (ETDEWEB)
Ryan, John James [MIT
1991-01-01
The E665 spectrometer at Fermila.b measured Deep-Inelastic Scattering of 490 GeV /c muons off several targets: Hydrogen, Deuterium, and Xenon. Events were selected from the Xenon and Deuterium targets, with a range of energy exchange, $\
Influence functionals in deep inelastic reactions
International Nuclear Information System (INIS)
Avishai, Y.
1978-01-01
It is suggested that the concept of influence functionals introduced by Feynman and Vernon could be applied to the study of deep inelastic reactions among heavy ions if the coupling between the relative motion and the internal degrees of freedom has a separable form as suggested by Hofmann and Siemens. (Auth.)
Coherence effects in deep inelastic scattering
International Nuclear Information System (INIS)
Andersson, B.; Gustafson, G.; Loennblad, L.; Pettersson, U.
1988-09-01
We present a framework for deep inelastic scattering, with bound state properties in accordance with a QCD force field acting like a vortex line in a colour superconducting vacuum, which implies some simple coherence effects. Within this scheme one may describe the results of present energies very well, but one obtains an appreciable depletion of gluon radiation in the HERA energy regime. (authors)
Inelastic transport theory for nanoscale systems
DEFF Research Database (Denmark)
Frederiksen, Thomas
2007-01-01
This thesis describes theoretical and numerical investigations of inelastic scat- tering and energy dissipation in electron transport through nanoscale sys- tems. A computational scheme, based on a combination of density functional theory (DFT) and nonequilibrium Green’s functions (NEGF), has been...
Gamma-rays from deep inelastic collisions
International Nuclear Information System (INIS)
Stephens, F.S.
1981-01-01
My objective in this talk is to consider the question: 'What can be learned about deep inelastic collisions (DIC) from studying the associated gamma-rays'. First, I discuss the origin and nature of the gamma-rays from DIC, then the kinds of information gamma-ray spectra contain, and finally come to the combination of these two subjects. (orig./HSI)
Deep inelastic scattering near the Coulomb barrier
International Nuclear Information System (INIS)
Gehring, J.; Back, B.; Chan, K.
1995-01-01
Deep inelastic scattering was recently observed in heavy ion reactions at incident energies near and below the Coulomb barrier. Traditional models of this process are based on frictional forces and are designed to predict the features of deep inelastic processes at energies above the barrier. They cannot be applied at energies below the barrier where the nuclear overlap is small and friction is negligible. The presence of deep inelastic scattering at these energies requires a different explanation. The first observation of deep inelastic scattering near the barrier was in the systems 124,112 Sn + 58,64 Ni by Wolfs et al. We previously extended these measurements to the system 136 Xe + 64 Ni and currently measured the system 124 Xe + 58 Ni. We obtained better statistics, better mass and energy resolution, and more complete angular coverage in the Xe + Ni measurements. The cross sections and angular distributions are similar in all of the Sn + Ni and Xe + Ni systems. The data are currently being analyzed and compared with new theoretical calculations. They will be part of the thesis of J. Gehring
Mean associated multiplicities in deep inelastic processes
International Nuclear Information System (INIS)
Dzhaparidze, G.Sh.; Kiselev, A.V.; Petrov, V.A.
1982-01-01
A formula is derived for the mean hadron multiplicity in the target fragmentation range of deep inelastic scattering processes. It is shown that in the high-x region the ratio of the mean multiplicities in the current fragmentation region and in the target fragmentation region tends to unity at high energies. The mean multiplicity for the Drell-Yan process is considered
Elastic and inelastic electron and muon scattering
International Nuclear Information System (INIS)
Hand, L.N.
1977-01-01
The current status of experiments in the field of elastic and inelastic electron and muon scattering is discussed. The talk is divided into discussions of the single arm inclusive experiments at SLAC and Fermilab; the multiparticle inclusive experiments at SLAC, Fermilab und Cornell, and a description of selected results from exclusive channel measurements on electroproduced final states. (orig.) [de
Approximate analyses of inelastic effects in pipework
International Nuclear Information System (INIS)
Jobson, D.A.
1983-01-01
This presentation shows figures concerned with analyses of inelastic effects in pipework as follows: comparison of experimental and calculated simplified analyses results for free end rotation and for circumferential strain; interrupted stress relaxation; regenerated relaxation caused by reversed yield; buckling of straight pipe under combined bending and torsion; results of fatigues test of pipe bend
Deep inelastic scattering near the Coulomb barrier
Energy Technology Data Exchange (ETDEWEB)
Gehring, J.; Back, B.; Chan, K. [and others
1995-08-01
Deep inelastic scattering was recently observed in heavy ion reactions at incident energies near and below the Coulomb barrier. Traditional models of this process are based on frictional forces and are designed to predict the features of deep inelastic processes at energies above the barrier. They cannot be applied at energies below the barrier where the nuclear overlap is small and friction is negligible. The presence of deep inelastic scattering at these energies requires a different explanation. The first observation of deep inelastic scattering near the barrier was in the systems {sup 124,112}Sn + {sup 58,64}Ni by Wolfs et al. We previously extended these measurements to the system {sup 136}Xe + {sup 64}Ni and currently measured the system {sup 124}Xe + {sup 58}Ni. We obtained better statistics, better mass and energy resolution, and more complete angular coverage in the Xe + Ni measurements. The cross sections and angular distributions are similar in all of the Sn + Ni and Xe + Ni systems. The data are currently being analyzed and compared with new theoretical calculations. They will be part of the thesis of J. Gehring.
Performance testing of a Fresnel/Stirling micro solar energy conversion system
International Nuclear Information System (INIS)
Aksoy, Fatih; Karabulut, Halit
2013-01-01
Highlights: • Solar energy has a big importance among the renewable energy sources. • A micro solar energy system consisted of a Stirling engine and Fresnel lens was tested. • Solar radiation was directly focused into a cavity. • Cavities made of copper, aluminium and stainless steel were used. • The maximum performance was obtained with aluminium cavity. - Abstract: In this study, a beta-type Stirling engine was tested with concentrated solar radiation. The displacer cylinder of the engine was modified by integrating a concentrated solar radiation receiver. Basically, the receiver is a cavity drilled in a separate part mounted on top of the displacer cylinder by screws. Tests were conducted with three cavities made of aluminium, copper and stainless steel. The solar radiation was concentrated by a Fresnel lens with 1.4 m 2 capture area. Among the cavities, the highest performance was provided by aluminium cavity and followed by the stainless steel and copper cavities respectively. The maximum shaft power was observed as 64.4 W at systematic tests conducted with the aluminium cavity. The maximum shaft power corresponded to 218 rpm engine speed and 2.82 Nm torque. For this shaft power, the overall conversion efficiency of the system was estimated to be 5.64%. The maximum torque measured with aluminium cavity was 2.93 Nm corresponding to 177 rpm below which the engine stopped. The Fresnel-lens/Stirling-engine micro power plant established in this investigation was more efficient than the micro power plants presented in the literature
DEFF Research Database (Denmark)
Loaldi, D.; Calaon, Matteo; Quagliotti, Danilo
, on an injection compression moulded (ICM) Fresnel lens, is defined. A set of two different objectives is considered, i.e. a standard series (SO), against a long working distance one (LWD); two different magnifications objectives, 50x and 100x and the use or not of a dark environment. The noise evaluation...... are measuring working distance, objective magnification and room lighting. The result confirms a strong difference of noise, using the considered objectives. The most interesting result is that the performance of SO 50x objective is better than LWD 100x....
O'Neill, Mark; McDanal, A. J.; Brandhorst, Henry; Spence, Brian; Iqbal, Shawn; Sharps, Paul; McPheeters, Clay; Steinfeldt, Jeff; Piszczor, Michael; Myers, Matt
2016-01-01
At the 42nd PVSC, our team presented recent advances in our space photovoltaic concentrator technology. These advances include more robust Fresnel lenses for optical concentration, more thermally conductive graphene radiators for waste heat rejection, improved color-mixing lens technology to minimize chromatic aberration losses with 4-junction solar cells, and an articulating photovoltaic receiver enabling single-axis sun-tracking, while maintaining a sharp focal line despite large beta angles of incidence. In the past year, under a NASA Phase II SBIR program, our team has made much additional progress in the development of this new space photovoltaic concentrator technology, as described in this paper.
Simanjuntak, Jerri
2015-01-01
It has been designed a thermoelectric generator to produce electricity. By utilizing solar heat as the hot side of the peltier element. Fresnel Lens is used to collect sunlight towards the aluminium plate which is directly on the hot side of the peltier element. The working principle of thermoelectric generator according to the Seebeck effect, where the presence of the temperature difference between the hot side and a cold side peltier there will be a flow of current to produce a voltage.Test...
Improvement of Quality of Reconstructed Images in Multi-Frame Fresnel Digital Holography
International Nuclear Information System (INIS)
Xiao-Wei, Lu; Jing-Zhen, Li; Hong-Yi, Chen
2010-01-01
A modified reconstruction algorithm to improve the quality of reconstructed images of multi-frame Fresnel digital holography is presented. When the reference beams are plane or spherical waves with azimuth encoding, by introducing two spherical wave factors, images can be reconstructed with only one time Fourier transform. In numerical simulation, this algorithm could simplify the reconstruction process and improve the signal-to-noise ratio of the reconstructed images. In single-frame reconstruction experiments, the accurate reconstructed image is obtained with this simplified algorithm
Directory of Open Access Journals (Sweden)
Kamil Yavuz Kapusuz
2014-06-01
Full Text Available In this study, a method for determining scattering center (or center of scattering points of a multipath is proposed, provided that the direction of arrival of the multipath is known by the receiver. The method is based on classical electromagnetic wave principles in order to determine scattering center over irregular terrain. Geometrical optics (GO along with Fresnel zone concept is employed, as the receiver, the transmitter positions and irregular terrain data are assumed to be provided. The proposed method could be used at UHF bands, especially, operations of radars and electronic warfare applications.
Application of up-sampling and resolution scaling to Fresnel reconstruction of digital holograms.
Williams, Logan A; Nehmetallah, Georges; Aylo, Rola; Banerjee, Partha P
2015-02-20
Fresnel transform implementation methods using numerical preprocessing techniques are investigated in this paper. First, it is shown that up-sampling dramatically reduces the minimum reconstruction distance requirements and allows maximal signal recovery by eliminating aliasing artifacts which typically occur at distances much less than the Rayleigh range of the object. Second, zero-padding is employed to arbitrarily scale numerical resolution for the purpose of resolution matching multiple holograms, where each hologram is recorded using dissimilar geometric or illumination parameters. Such preprocessing yields numerical resolution scaling at any distance. Both techniques are extensively illustrated using experimental results.
The Fresnel mode of Lorentz microscopy using a scanning transmission electron microscope
International Nuclear Information System (INIS)
Chapman, J.N.; Waddell, E.M.; Batson, P.E.; Ferrier, R.P.
1979-01-01
The most widely used method of investigating ferromagnetic films in the transmission electron microscope is the Fresnel or defocus mode of Lorentz microscopy. This may be implemented either in a fixed beam or a scanning instrument. Despite a rather inefficient utilization of electrons, several advantages accrue if the latter is used, and provided it is equipped with a field emission gun, low noise images may be obtained in acceptable recording times. To extract quantitative estimates of domain wall widths from such images it is necessary to measure accurately both instrumental and specimen parameters. Methods for this are discussed and an example of an analysis using a polycrystalline permalloy film is given. (Auth.)
Fresnel: O formulador matemático da teoria ondulatória da luz
Bassalo, José Maria Filardo
1988-01-01
Neste artigo, apresentamos alguns aspectos da vida de Fresnel, engenheiro e físico francês que se notabilizou pela formulação matemática da teoria ondulatória da luz, e cujo bicentenário de nascimento transcorre neste ano de 1988. Realçamos, neste trabalho, suas principais pesquisas relacionadas com o estudo da difração, dupla-refração e reflexão da luz, nas quais utilizou a idéia revolucionária de transversalidade da onda luminosa para deduzir equações, as quais explicaram alg...
Srisungsitthisunti, Pornsak; Ersoy, Okan K; Xu, Xianfan
2009-01-01
Light diffraction by volume Fresnel zone plates (VFZPs) is simulated by the Hankel transform beam propagation method (Hankel BPM). The method utilizes circularly symmetric geometry and small step propagation to calculate the diffracted wave fields by VFZP layers. It is shown that fast and accurate diffraction results can be obtained with the Hankel BPM. The results show an excellent agreement with the scalar diffraction theory and the experimental results. The numerical method allows more comprehensive studies of the VFZP parameters to achieve higher diffraction efficiency.
Femtosecond laser-ablated Fresnel zone plate fiber probe and sensing applications
Tan, Xiaoling; Geng, Youfu; Chen, Yan; Li, Shiguo; Wang, Xinzhong
2018-02-01
We investigate the Fresnel zone plate (FZP) inscribed on multimode fiber endface using femtosecond laser ablation and its application in sensing. The mode transmission through fiber tips with FZP is investigated both by the beam propagation method theoretically and by measuring the beam images with a charge-coupled device camera experimentally, which show a good agreement. Such devices are tested for surface-enhanced Raman scattering (SERS) using the aqueous solution of rhodamine 6G under a Raman spectroscopy. The experimental results demonstrate that the SERS signal is enhanced benefiting from focal ability of FZP, which is a promising method for the particular biochemical spectra sensing applications.
Inelastic electron scattering from a moving nucleon
Energy Technology Data Exchange (ETDEWEB)
Kuhn, S.E. [Old Dominion Univ., Norfolk, VA (United States); Griffioen, K. [College of William and Mary, Williamsburg, VA (United States)
1994-04-01
The authors propose to measure inelastically scattered electrons in coincidence with spectator protons emitted backwards relative to the virtual photon direction in the reaction d(e, e{prime}p{sub s})X. In a simple spectator model, the backward proton has equal and opposite momentum to the neutron before it is struck, allowing the authors to study the dependence on kinematics and off-shell behaviour of the electron-nucleon inelastic cross section. If the photon couples to a quark in a 6-quark bag, a different dependence of the cross section on the kinematic variables (x, Q{sup 2}, and p{sub s}) can be observed. This proposed experiment requires large acceptance and beam energies above 6 GeV. It is ideally suited for the CEBAF Large Acceptance Spectrometer (CLAS).
Review of inelastic proton-proton reactions
Morrison, Douglas Robert Ogston
1973-01-01
The most important new results on inelastic proton-proton scattering obtained with the new machines, I.S.R. and N.A.L., are: (1) The inelastic cross-section increases monotonically with energy from threshold to 1500 GeV/c. Above 6 GeV/c the energy variation has a s /sup +0.04/ behaviour. (2) Scaling is observed at I.S.R. energies in pion production. Confirmation is obtained of the hypothesis of limiting fragmentation. (3) The results are in general, consistent with the two-component model-one class of events being produced by diffraction dissociation and the other by a short-range-order process (e.g. the multiperipheral model). (4) There are indications that the protons have a granular structure; this from observation of secondaries of large transverse momenta. (33 refs).
Response of subsystems on inelastic structures
International Nuclear Information System (INIS)
Lin, J.; Mahin, S.A.
1984-01-01
Preliminary analysis are performed to obtain insight into the seismic response of subsystems supported on simple structures that yield during severe earthquake ground motions. Current design recommendations for subsystems accounting for yielding of the supporting structures are assessed and found to be unconservative. An amplification factor is defined to quantify the effects of inelastic deformations of the supporting structure on subsystem response. Design guidelines are formulated for predicting the amplification factor based on statistical evaluation of the results generated for ten earthquake ground motions. Using these values, design floor response spectra can be obtained from conventional linear elastic floor response spectra accounting for yielding of the supporting structure without having to perform inelastic analysis. The effects of non-zero subsystem mass are examined. The recommended amplification factors are found to be applicable even when the mass of subsystem approaches that of the supporting structure
Parity violation in deep inelastic electron scattering
International Nuclear Information System (INIS)
Taylor, R.E.
1979-11-01
Neutral currents in electron scattering and the Weinberg-Salam model are reviewed. This generally accepted model is consistent with experimental results from neutrino interactions; an appropriate deep inelastic electron scattering experiment would measure couplings that don't involve neutrinos to see if they are also correctly described by the theory. The SLAC-Yale experiment measures a difference in the e-d inelastic cross section for right- and left-handed electrons. The polarized source, beam monitors, scattering experiment, checks of helicity dependence, and results are described. It is concluded that the data obtained are in agreement with the Weinberg-Salam model, and that the best value of sin 2 theta/sub W/ for these data is in excellent agreement with the average values of that parameter deduced from neutrino experiments. Future experiments with polarized electrons are discussed. 12 figures, 2 tables
On a simplified inelastic analysis of structures
International Nuclear Information System (INIS)
Zarka, J.; Engel, J.J.; Inglebert, G.
1980-01-01
In this paper two main problems are considered: the derivation of cyclic constitutive relations during inelastic regime where hardening, softening and creep can occur, and the development of the eventual periodical state in the structure during cyclic thermodynamical loadings. We give a very simple and practical framework to solve these problems in one unique manner. Its essential feature consits in the introduction of a family of internal parameters which characterize local inelastic mechanisms and the family of transformed internal parameters which are linearly linked to the previous ones through a symmetrical non-negative matrix and are indeed the opposite of the associated residual stresses. Thanks to that, the treatment of the local plastic or viscoplastic yield conditions can be easily made from only the classical simple purely elastic (or viscoelastic) analysis. This property allows important results during cyclic loadings: conditions for elastic shakedown, plastic shakedown, ratcheting and bounds for the limiting state. Several examples are given in the text. (orig.)
Inelastic analysis of solids and structures
Kojic, M; Bathe, K J; Koji?, Milo
2005-01-01
Inelastic Analysis of Solids and Structures presents in a unified manner the physical and theoretical background of inelastic material models and computational methods, and illustrates the behavior of the models in typical engineering conditions.It is based on experimental observations and principles of mechanics, thus describing computational algorithms for stress calculation and presenting solved examples.The theoretical background is given to an extent necessary to describe the commonly employed material models in metal isotropic and orthotropic plasticity, thermoplasticity and viscoplasticity, and the plasticity of geological materials.The computational algorithms are developed in a unified manner with some detailed derivations of the algorithmic relations.The solved examples are designed to give insight into the material behavior in various engineering conditions, and to demonstrate the application of the computational algorithms.
Effective exchange potentials for electronically inelastic scattering
International Nuclear Information System (INIS)
Schwenke, D.W.; Staszewska, G.; Truhlar, D.G.
1983-01-01
We propose new methods for solving the electron scattering close coupling equations employing equivalent local exchange potentials in place of the continuum-multiconfiguration-Hartree--Fock-type exchange kernels. The local exchange potentials are Hermitian. They have the correct symmetry for any symmetries of excited electronic states included in the close coupling expansion, and they have the same limit at very high energy as previously employed exchange potentials. Comparison of numerical calculations employing the new exchange potentials with the results obtained with the standard nonlocal exchange kernels shows that the new exchange potentials are more accurate than the local exchange approximations previously available for electronically inelastic scattering. We anticipate that the new approximations will be most useful for intermediate-energy electronically inelastic electron--molecule scattering
On deep inelastic lepton-nuclear interactions
International Nuclear Information System (INIS)
Garsevanishvili, V.R.; Darbaidze, Ya.Z.; Menteshashvili, Z.R.; Ehsakiya, Sh.M.
1981-01-01
The problem of building relativistic theory of nuclear reactions by way of involving relativistic methods, developed in the elementary particle theory, becomes rather actual at the time being. The paper presents some results of investigations into deep inelastic lepton-nuclear processes lA → l'(A-1)x, with the spectator nucleus-fragment in the finite state. To describe the reactions lA → l'(A-1)x (where l=an electron, muan, neutrino, antineutrino), the use is made of the self-similarity principle and multiparticle quasipotential formalism in the ''light front'' variables. The expressions are obtained for the differential cross-sections of lepton-nuclear processes and for the structure functions of deep inelastic scattering of neutrinos (antineutrinos) and charged leptons by nuclei
Energy Technology Data Exchange (ETDEWEB)
Setiadi, Herlan; Nurhandoko, Bagus Endar B.; Wely, Woen [WISFIR Lab., Physics of Complex System, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Bandung 40132 (Indonesia); Riyanto, Erwin [PT Freeport Indonesia, Tembagapura, Indonesia herlansetiadi@yahoo.com (Indonesia)
2015-04-16
Fracture prediction in a block cave of underground mine is very important to monitor the structure of the fracture that can be harmful to the mining activities. Many methods can be used to obtain such information, such as TDR (Time Domain Relectometry) and open hole. Both of them have limitations in range measurement. Passive seismic tomography is one of the subsurface imaging method. It has advantage in terms of measurements, cost, and rich of rock physical information. This passive seismic tomography studies using Fresnel zone to model the wavepath by using frequency parameter. Fresnel zone was developed by Nurhandoko in 2000. The result of this study is tomography of P and S wave velocity which can predict position of fracture. The study also attempted to use sum of the wavefronts to obtain position and time of seismic event occurence. Fresnel zone tomography and the summation wavefront can predict location of geological structure of mine area as well.
Inelastic neutron scattering from superconducting rings
International Nuclear Information System (INIS)
Agafonov, A.I.
2010-01-01
For the first time the differential cross section for the inelastic magnetic neutron scattering by superconducting rings is derived taking account of the interaction of the neutron magnetic moment with the magnetic field generated by the superconducting current. Calculations of the scattering cross section are carried out for cold neutrons and thin film rings from type-II superconductors with the magnetic fields not exceeding the first critical field.
Coulomb Distortion in the Inelastic Regime
Energy Technology Data Exchange (ETDEWEB)
Patricia Solvignon, Dave Gaskell, John Arrington
2009-09-01
The Coulomb distortion effects have been for a long time neglected in deep inelastic scattering for the good reason that the incident energies were very high. But for energies in the range of earlier data from SLAC or at JLab, the Coulomb distortion could have the potential consequence of affecting the A-dependence of the EMC effect and of the longitudinal to transverse virtual photon absorption cross section ratio $R(x,Q^2)$.
Deep inelastic collisions viewed as Brownian motion
International Nuclear Information System (INIS)
Gross, D.H.E.; Freie Univ. Berlin
1980-01-01
Non-equilibrium transport processes like Brownian motion, are studied since perhaps 100 years and one should ask why does one not use these theories to explain deep inelastic collision data. These theories have reached a high standard of sophistication, experience, and precision that I believe them to be very usefull for our problem. I will try to sketch a possible form of an advanced theory of Brownian motion that seems to be suitable for low energy heavy ion collisions. (orig./FKS)
Recent advances in elasticity, viscoelasticity and inelasticity
Rajagopal, KR
1995-01-01
This is a collection of papers dedicated to Prof T C Woo to mark his 70th birthday. The papers focus on recent advances in elasticity, viscoelasticity and inelasticity, which are related to Prof Woo's work. Prof Woo's recent work concentrates on the viscoelastic and viscoplastic response of metals and plastics when thermal effects are significant, and the papers here address open questions in these and related areas.
Deuteron structure in the deep inelastic regime
Energy Technology Data Exchange (ETDEWEB)
Garcia Canal, C.A.; Tarutina, T. [Universidad Nacional de La Plata, IFLP/CONICET y Departamento de Fisica, La Plata (Argentina); Vento, V. [Universidad de Valencia-CSIC, Departamento de Fisica Teorica-IFIC, Burjassot (Valencia) (Spain)
2017-06-15
We study nuclear effects in the deuteron in the deep inelastic regime using the newest available data. We put special emphasis on their Q{sup 2} dependence. The study is carried out using a scheme which parameterizes, in a simple manner, these effects by changing the proton and neutron stucture functions in medium. The result of our analysis is compared with other recent proposals. We conclude that precise EMC ratios cannot be obtained without considering the nuclear effects in the deuteron. (orig.)
Inelastic neutron scattering from cerium under pressure
International Nuclear Information System (INIS)
Rainford, B.D.; Buras, B.; Lebech, B.
1976-01-01
Inelastic neutron scattering from Ce metal at 300K was studied both below and above the first order γ-α phase transition, using a triple axis spectrometer. It was found that (a) there is no indication of any residual magnetic scattering in the collapsed α phase and (b) the energy width of the paramagnetic scattering in the γ-phase increases with pressure. (Auth.)
Deep Inelastic Scattering at the Amplitude Level
International Nuclear Information System (INIS)
Brodsky, Stanley J.
2005-01-01
The deep inelastic lepton scattering and deeply virtual Compton scattering cross sections can be interpreted in terms of the fundamental wavefunctions defined by the light-front Fock expansion, thus allowing tests of QCD at the amplitude level. The AdS/CFT correspondence between gauge theory and string theory provides remarkable new insights into QCD, including a model for hadronic wavefunctions which display conformal scaling at short distances and color confinement at large distances
Mean associated multiplicities in deep inelastic processes
International Nuclear Information System (INIS)
Dzhaparidze, G.S.; Kiselev, A.V.; Petrov, V.A.
1982-01-01
A formula is derived for the mean multiplicity of hadrons in the target-fragmentation region in the process of deep inelastic scattering. It is shown that in the region of large x the ratio of the mean multiplicities in the current- and target-fragmentation regions tends to unity at high energies. The mean multiplicity in the Drell-Yan process is also discussed
Colour coherence in deep inelastic Compton scattering
Energy Technology Data Exchange (ETDEWEB)
Lebedev, A.I.; Vazdik, J.A. (Lebedev Physical Inst., Academy of Sciences, Moscow (USSR))
1992-01-01
MC simulation of Deep Inelastic Compton on proton - both QED and QCD - was performed on the basis of LUCIFER program for HERA energies. Charged hadron flow was calculated for string and independent fragmentation with different cuts on p{sub t} and x. It is shown that interjet colour coherence leads in the case of QCD Compton to the drag effects diminishing the hadron flow in the direction between quark jet and proton remnant jet. (orig.).
Colour coherence in deep inelastic Compton scattering
International Nuclear Information System (INIS)
Lebedev, A.I.; Vazdik, J.A.
1992-01-01
MC simulation of Deep Inelastic Compton on proton - both QED and QCD - was performed on the basis of LUCIFER program for HERA energies. Charged hadron flow was calculated for string and independent fragmentation with different cuts on p t and x. It is shown that interjet colour coherence leads in the case of QCD Compton to the drag effects diminishing the hadron flow in the direction between quark jet and proton remnant jet. (orig.)
Inelastic analysis of prestressed concrete secondary containments
International Nuclear Information System (INIS)
Murray, D.W.; Chitnuyanondh, L.; Wong, C.; Rijub-Agha, K.Y.
1978-07-01
An elastic-plastic constitutive model for the simulation of stress-strain response of concrete under any biaxial combination of compressive and/or tensile stresses is developed. An effective tensile stress-strain curve is obtained indirectly from experimental results of a test on a large scale prestressed concrete wall segment. These concrete properties are then utilized in predicting the response of a second test and the results compared with the experiment. Modificications to the BOSOR5 program, in order to incorporate the new constitutive relation into it, are described. Techniques of modelling structures in order to perform inelastic analysis of thin shell axisymmetric prestressed concrete secondary containments are investigated. The results of inelastic BOSOR5 analyses of two different models of the University of Alberta Test Structure are presented. The predicted deterioration of the structure and the limit states associated with its behaviour are determined and discussed. It is concluded that the technique is a practical one which can be used for the inelastic analysis of Gentilly-type containment structures. (author)
Deep-inelastic electron-proton diffraction
International Nuclear Information System (INIS)
Dainton, J.B.
1995-11-01
Recent measurements by the H1 collaboration at HERA of the cross section for deep-inelastic electron-proton scattering in which the proton interacts with minimal energy transfer and limited 4-momentum transfer squared are presented in the form of the contribution F 2 D(3) to the proton structure function F 2 . By parametrising the cross section phenomenologically in terms of a leading effective Regge pole exchange and comparing the result with a similar parametrisation of hadronic pp physics, the proton interaction is demonstrated to be dominantly of a diffractive nature. The quantitative interpretation of the parametrisation in terms of the properties of an effective leading Regge pole exchange, the pomeron (IP), shows that there is no evidence for a 'harder' BFKL-motivated IP in such deep-inelastic proton diffraction. The total contribution of proton diffraction to deep-inelastic electron-proton scattering is measured to be ∝10% and to be rather insensitive to Bjorken-x and Q 2 . A first measurement of the partonic structure of diffractive exchange is presented. It is shown to be readily interpreted in terms of the exchange of gluons, and to suggest that the bulk of diffractive momentum transfer is carried by a leading gluon. (orig.)
Design and thermal performances of a scalable linear Fresnel reflector solar system
International Nuclear Information System (INIS)
Zhu, Yanqing; Shi, Jifu; Li, Yujian; Wang, Leilei; Huang, Qizhang; Xu, Gang
2017-01-01
Highlights: • A scalable linear Fresnel reflector which can supply different temperatures is proposed. • Inclination design of the mechanical structure is used to reduce the end losses. • The maximum thermal efficiency of 64% is achieved in Guangzhou. - Abstract: This paper proposes a scalable linear Fresnel reflector (SLFR) solar system. The optical mirror field which contains an array of linear plat mirrors closed to each other is designed to eliminate the inter-low shading and blocking. Scalable mechanical mirror support which can place different number of mirrors is designed to supply different temperatures. The mechanical structure can be inclined to reduce the end losses. Finally, the thermal efficiency of the SLFR with two stage mirrors is tested. After adjustment, the maximum thermal efficiency of 64% is obtained and the mean thermal efficiency is higher than that before adjustment. The results indicate that the end losses have been reduced effectively by the inclination design and excellent thermal performance can be obtained by the SLFR after adjustment.
Yadav, Poonam Lata; Singh, Hukum
2018-05-01
To enhance the security in optical image encryption system and to protect it from the attackers, this paper proposes new digital spiral phase mask based on Fresnel Transform. In this cryptosystem the Spiral Phase Mask (SPM) used is a hybrid of Fresnel Zone Plate (FZP) and Radial Hilbert Mask (RHM) which makes the key strong and enhances the security. The different keys used for encryption and decryption purposed make the system much more secure. Proposed scheme uses various structured phase mask which increases the key space also it increases the number of parameters which makes it difficult for the attackers to exactly find the key to recover the original image. We have also used different keys for encryption and decryption purpose to make the system much more secure. The strength of the proposed cryptosystem has been analyzed by simulating on MATLAB 7.9.0(R2008a). Mean Square Errors (MSE) and Peak Signal to Noise Ratio (PSNR) are calculated for the proposed algorithm. The experimental results are provided to highlight the effectiveness and sustainability of proposed cryptosystem and to prove that the cryptosystem is secure for usage.
Emergence of Fresnel diffraction zones in gravitational lensing by a cosmic string
Energy Technology Data Exchange (ETDEWEB)
Fernández-Núñez, Isabel [Departament de Física Quàntica i Astrofísica, Facultat de Física, Universitat de Barcelona, Martí i Franquès 1, E-08028 Barcelona (Spain); Institut de Ciències del Cosmos (ICCUB), Facultat de Física, Universitat de Barcelona, Martí i Franquès 1, E-08028 Barcelona (Spain); Bulashenko, Oleg, E-mail: oleg.bulashenko@ub.edu [Departament de Física Quàntica i Astrofísica, Facultat de Física, Universitat de Barcelona, Martí i Franquès 1, E-08028 Barcelona (Spain)
2017-06-09
The possibility to detect cosmic strings – topological defects of early Universe, by means of wave effects in gravitational lensing is discussed. To find the optimal observation conditions, we define the hyperbolic-shaped Fresnel observation zones associated with the diffraction maxima and analyse the frequency patterns of wave amplification corresponding to different alignments. In particular, we show that diffraction of gravitational waves by the string may lead to significant amplification at cosmological distances. The wave properties we found are quite different from what one would expect, for instance, from light scattered off a thin wire or slit, since a cosmic string, as a topological defect, gives no shadow at all. - Highlights: • Interference and diffraction of gravitational waves by a cosmic string are studied. • Uniform asymptotic theory of diffraction is applied for a finite distance source. • Hyperbolic-shaped Fresnel observation zones associated with maxima of diffraction. • Frequency patterns modulated by diffraction for different string alignments are given. • The method is applicable to condensed-matter defects and other types of waves.
Smith, David R.; Gowda, Vinay R.; Yurduseven, Okan; Larouche, Stéphane; Lipworth, Guy; Urzhumov, Yaroslav; Reynolds, Matthew S.
2017-01-01
Wireless power transfer (WPT) has been an active topic of research, with a number of WPT schemes implemented in the near-field (coupling) and far-field (radiation) regimes. Here, we consider a beamed WPT scheme based on a dynamically reconfigurable source aperture transferring power to receiving devices within the Fresnel region. In this context, the dynamic aperture resembles a reconfigurable lens capable of focusing power to a well-defined spot, whose dimension can be related to a point spread function. The necessary amplitude and phase distribution of the field imposed over the aperture can be determined in a holographic sense, by interfering a hypothetical point source located at the receiver location with a plane wave at the aperture location. While conventional technologies, such as phased arrays, can achieve the required control over phase and amplitude, they typically do so at a high cost; alternatively, metasurface apertures can achieve dynamic focusing with potentially lower cost. We present an initial tradeoff analysis of the Fresnel region WPT concept assuming a metasurface aperture, relating the key parameters such as spot size, aperture size, wavelength, and focal distance, as well as reviewing system considerations such as the availability of sources and power transfer efficiency. We find that approximate design formulas derived from the Gaussian optics approximation provide useful estimates of system performance, including transfer efficiency and coverage volume. The accuracy of these formulas is confirmed through numerical studies.
Thermal performance of a linear Fresnel reflector solar concentrator PV/T energy systems
Energy Technology Data Exchange (ETDEWEB)
Gomaa, Mohamed R. [State Engineering University of Armenia (Armenia)], E-Mail: Dmoh_elbehary@yahoo.com
2011-07-01
This is a report on an investigation of photovoltaic/thermal (PV/T) collectors. Solar energy conversion efficiency was increased by taking advantage of PV/T collectors and low solar concentration technologies, combined into a PV/T system operated at elevated temperature. The main novelty is the coupling of a linear Fresnel mirror reflecting concentrator with a channel PV/T collector. Concentrator PV/T collectors can function at temperatures over 100 degrees celsius, and thus thermal energy can be made to drive processes such as refrigeration, desalination and steam production. Solar system analytical thermal performance gives efficiency values over 60%. Combined electric and thermal (CET) efficiency is high. A combined electric and heat power for the linear fresnel reflector approach that employs high performance CPV technology to produce both electricity and thermal energy at low to medium temperatures is presented. A well-functioning PV/T system can be designed and constructed with low concentration and a total efficiency of nearly 80% can be attained.
Development of a Fresnel lens for cold neutrons based on neutron refractive optics
Oku, T; Moriyasu, S; Yamagata, Y; Ohmori, H; Takizawa, Y; Shimizu, H M; Hirota, T; Kiyanagi, Y; Ino, T; Furusaka, M; Suzuki, J
2001-01-01
We have developed compound refractive lenses (CRLs) for cold neutrons, which are made of vitreous silica and have an effective potential of (90.1-2.7x10 sup - sup 4 i) neV. In the case of compound refractive optics, neutron absorption by the material deteriorates lens performance. Thus, to prevent an increase in neutron absorption with increasing beam size, we have developed Fresnel lenses using the electrolytic in-process dressing grinding technique. The lens characteristics were carefully investigated with experimental and numerical simulation studies. The lenses functioned as a neutron focusing lens, and the focal length of 14 m was obtained with a 44-element series of the Fresnel lenses for 10 A neutrons. Moreover, good neutron transmission of 0.65 for 15 A neutrons was obtained due to the shape effect. According to comprehensive analysis of the obtained results, it is possible to realize a CRL for practical use by choosing a suitable lens shape and material.
[System design of open-path natural gas leakage detection based on Fresnel lens].
Xia, Hui; Liu, Wen-Qing; Zhang, Yu-Jun; Kan, Rui-Feng; Cui, Yi-Ben; Wang, Min; He, Ying; Cui, Xiao-Juan; Ruan, Jun; Geng, Hui
2009-03-01
Based on the technology of tunable diode laser absorption spectroscopy (TDLAS) in conjunction with second harmonic wave detection, a long open-path TDLAS system using a 1.65 microm InGaAsP distributed feedback laser was developed, which is used for detecting pipeline leakage. In this system, a high cost performance Fresnel lens is used as the receiving optical system, which receives the laser-beam reflected by a solid corner cube reflector, and focuses the receiving laser-beam to the InGaAs detector. At the same time, the influences of the concentration to the fluctuation of light intensity were taken into account in the process of measurement, and were eliminated by the method of normalized light intensity. As a result, the measurement error caused by the fluctuation of light intensity was made less than 1%. The experiment of natural gas leakage detection was simulated, and the detection sensitivity is 0.1 x 10(-6) (ratio by volume) with a total path of 320 m. According to the receiving light efficiency of the optical system and the detectable minimum light intensity of the detector, the detectable maximal optical path of the system was counted to be 2 000 m. The results of experiment show that it is a feasible design to use the Fresnel lens as the receiving optical system and can satisfy the demand of the leakage detection of natural gas.
From Mie to Fresnel through effective medium approximation with multipole contributions
International Nuclear Information System (INIS)
Malasi, Abhinav; Kalyanaraman, Ramki; Garcia, Hernando
2014-01-01
The Mie theory gives the exact solution to scattering from spherical particles while the Fresnel theory provides the solution to optical behavior of multilayer thin film structures. Often, the bridge between the two theories to explain the behavior of materials such as nanoparticles in a host dielectric matrix, is done by effective medium approximation (EMA) models which exclusively rely on the dipolar response of the scattering objects. Here, we present a way to capture multipole effects using EMA. The effective complex dielectric function of the composite is derived using the Clausius–Mossotti relation and the multipole coefficients of the approximate Mie theory. The optical density (OD) of the dielectric slab is then calculated using the Fresnel approach. We have applied the resulting equation to predict the particle size dependent dipole and quadrupole behavior for spherical Ag nanoparticles embedded in glass matrix. This dielectric function contains the relevant properties of EMA and at the same time predicts the multipole contributions present in the single particle Mie model. (papers)
Implementation of real-time multiple reflection and Fresnel absorption of laser beam in keyhole
International Nuclear Information System (INIS)
Cho, Jung-Ho; Na, Suck-Joo
2006-01-01
A computational analysis of laser keyhole welding is achieved. The main driving force to make the molten pool as a narrow and deep keyhole is the recoil pressure induced by evaporation of the material. Also, the multiple reflection effect on the keyhole wall plays an important role in making the keyhole deeper and raising its total energy absorption rate. Multiple reflection and Fresnel absorption are implemented simultaneously with the proposed ray tracing technique in a discrete grid cell system during the simulation for every single time step. In particular, the Fresnel absorption model is chosen as an energy transfer mechanism from laser beam to workpiece. With all the governing equations including continuity, momentum and energy equation, the VOF method is adopted to trace the free surface of the molten pool. Simulation results are compared with the experimental ones to verify its validity. A pulsed Nd : YAG laser was used for keyhole welding experiments on mild steel plates of 7 mm thickness. It was observed that the generated keyhole maintains its solidified shape without any closing phenomenon both in the experiments and in the simulations
Implementation of real-time multiple reflection and Fresnel absorption of laser beam in keyhole
Energy Technology Data Exchange (ETDEWEB)
Cho, Jung-Ho; Na, Suck-Joo [Department of Mechanical Engineering, KAIST, 373-1 Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of)
2006-12-21
A computational analysis of laser keyhole welding is achieved. The main driving force to make the molten pool as a narrow and deep keyhole is the recoil pressure induced by evaporation of the material. Also, the multiple reflection effect on the keyhole wall plays an important role in making the keyhole deeper and raising its total energy absorption rate. Multiple reflection and Fresnel absorption are implemented simultaneously with the proposed ray tracing technique in a discrete grid cell system during the simulation for every single time step. In particular, the Fresnel absorption model is chosen as an energy transfer mechanism from laser beam to workpiece. With all the governing equations including continuity, momentum and energy equation, the VOF method is adopted to trace the free surface of the molten pool. Simulation results are compared with the experimental ones to verify its validity. A pulsed Nd : YAG laser was used for keyhole welding experiments on mild steel plates of 7 mm thickness. It was observed that the generated keyhole maintains its solidified shape without any closing phenomenon both in the experiments and in the simulations.
Energy Technology Data Exchange (ETDEWEB)
Jin Xiangzhong [Laser Institute of Hunan University, Changsha, Hunan, 410082 (China); Berger, Peter [Institut fuer Strahlwerkzeuge (IFSW), University of Stuttgart, Pfaffenwaldring 43, 70569 Stuttgart (Germany); Graf, Thomas [Institut fuer Strahlwerkzeuge (IFSW), University of Stuttgart, Pfaffenwaldring 43, 70569 Stuttgart (Germany)
2006-11-07
In laser welding experiments of glass, keyhole shapes are observed by two high-speed cameras from two perpendicular directions. From the obtained keyhole pictures, it can be seen that in medium- and low-speed laser penetration welding, the main distortion of the keyhole is not the section metamorphosis from rotational symmetry, but the bending of its centre line. Based on such a keyhole photograph, the keyhole profiles and its centre line are determined by the method of polynomial fitting. Then, under the assumption of a circular cross section at each depth of the keyhole, the behaviour of the laser beam in the keyhole is analysed by tracing a ray of light using geometrical optics theory; the Fresnel absorption and multiple reflections in the keyhole are systematically studied, and the laser intensities absorbed on the keyhole walls are calculated. The absorbed laser intensity is not distributed uniformly on the keyhole wall. The keyhole wall absorbs laser intensity mainly on the half-part of the keyhole wall near the front wall. Because of the high absorptivity of the glass, Fresnel absorption from the first incidence of a laser beam plays a dominant role in the final laser intensity distribution on the keyhole wall, multiple reflections have some minor effects on the intensity distribution on the bottom part of the keyhole.
Theory of deep inelastic lepton-hadron scattering
International Nuclear Information System (INIS)
Geyer, B.; Robaschik, D.; Wieczorek, E.
1979-01-01
The description of deep inelastic lepton-nucleon scattering in the lowest order of the electromagnetic and weak coupling constants leads to a study of virtual Compton amplitudes and their absorptive parts. Some aspects of quantum chromodynamics are discussed. Deep inelastic scattering enables a central quantity of quantum field theory, namely the light cone behaviour of the current commutator. The moments of structure functions are used for the description of deep inelastic scattering. (author)
Energy Technology Data Exchange (ETDEWEB)
Aihara, T; Suzuki, A; Fujibayashi, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)
1997-11-25
A high concentration light collection system for solar chemistry was devised by using an inexpensive Fresnel lens in a primary concentration system and a conical type concentrator in a secondary concentration system. A Fresnel lens alone would not achieve sufficiently high light collecting magnification to attain high temperatures because of restrictions in the opening angle as seen from a focus. Therefore, a secondary concentration system was installed on a focus for an attempt of stopping. Reflection plane of a three-dimensional compound parabolic concentrator (CPC) is a rotary parabolic plane, whose process is expensive because of its surface processing accuracy. Therefore, a conical type concentrator was employed as a secondary concentration system. This system may not be capable of achieving as high concentration as in the CPC, but its shape is simple and it is inexpensive. In its optimization, a complete black body surface placed in vacuum atmosphere was hypothesized as a light concentrating part for the secondary concentration system to calculate heat collecting efficiencies at respective temperature settings. Using simultaneously the secondary concentration system, rather than collecting heat by using a Fresnel lens alone, has attained as high value as from 5.99% (500 degC) to 43.47% (1400 degC). Economical high-temperature heat collection of solar chemistry level may be possible by using a Fresnel lens and a conical secondary concentration system. 1 ref., 7 figs., 2 tabs.
Rossen, E.T.R.; Flipse, C.F.J.; Cerda, J.I.
2013-01-01
We have developed an efficient and accurate formalism which allows the simulation at the ab initio level of inelastic electron tunneling spectroscopy data under a scanning tunneling microscope setup. It exploits fully the tunneling regime by carrying out the structural optimization and vibrational
International Nuclear Information System (INIS)
Xie, W.T.; Dai, Y.J.; Wang, R.Z.
2011-01-01
Research highlights: → We studied a point focus Fresnel solar collector using different cavity receivers. → The collector heat removal factors are derived to find the optimal cavity shape. → Numerical and experimental analysis shows that the conical cavity is optimum. -- Abstract: A high concentration imaging Fresnel solar collector provided with different cavity receivers was developed and its behavior was investigated. Round copper pipes winded into different spring shapes were used as receiver by placing in the cylindrical cavity to absorb concentrated solar energy and transfer it to a heat transfer fluid (HTF). The collector efficiency factor and collector heat removal factor were derived for the cavity receivers to find out heat transfer mechanism and to propose an effective way for evaluating the performance of Fresnel solar collector and determining the optimal cavity structure. The problem of Fresnel solar collector with synthetic heat transfer oil flow was simulated and analyzed to investigate heat loss from different cavity receivers. Solar irradiation as well as convection and heat transfer in the circulating fluid and between the internal surfaces of the cavity and the environment are considered in the model. The temperature distribution over its area as well as the collector thermal efficiency at nominal flow rate was used in order to validate the simulation results. It was found that the simulated temperature distribution during operation and the average collector efficiency are in good agreement with the experimental data. Finally, the optimal shape of solar cavity receiver, as well as its thermal performance, are deeply analyzed and discussed.
Surface wear of TiN coated nickel tool during the injection moulding of polymer micro Fresnel lenses
DEFF Research Database (Denmark)
Tosello, Guido; Hansen, Hans Nørgaard; Gasparin, Stefania
2012-01-01
Limited tool life of nickel mould inserts represents an issue for the mass-production of polymer optics with complex micro three-dimensional geometries by injection moulding. TiN coating was applied to a nickel insert for the injection moulding of polycarbonate micro Fresnel lenses. Surface wear...
B.A.J. van Tuijl; Piet Sonneveld; J. Campen; Gert-Jan Swinkels; H.J.J. Janssen; G.P.A Bot
2011-01-01
A new type of greenhouse with linear Fresnel lenses in the cover performing as a concentrated photovoltaic (CPV) system is presented. The CPV system retains all direct solar radiation, while diffuse solar radiation passes through and enters into the greenhouse cultivation system. The removal of all
Deep inelastic scattering and asymptotic freedom
International Nuclear Information System (INIS)
Nachtmann, O.
1985-01-01
I recall some facets of the history of the field of deep inelastic scattering. I show how there was a very fruitful interplay between phenomenology on the one side and more abstract field theoretical considerations on the other side, where Kurt Symanzik, whose memory we honour today, made important contributions. Finally I make some remarks on the most recent developments in this field which have to do with the so-called EMC-effect, where EMC stands for European Muon Collaboration. (orig./HSI)
Deep inelastic scattering of heavy ions
International Nuclear Information System (INIS)
Brink, D.M.
1980-01-01
These lectures developed path integral methods for use in the theory of heavy ion reactions. The effects of internal degrees of freedom on the relative motion were contained in an influence functional which was calculated for several simple models of the internal structure. In each model the influence functional had a simple Gaussian structure suggesting that the relative motion of the nuclei in a deep inelastic collision could be described by a Langevin equation. The form of the influence functional determines the average damping force and the correlation function of the fluctuating Langevin force. (author)
Deep inelastic scattering of heavy ions
International Nuclear Information System (INIS)
Brink, D.M.
1980-01-01
These lecture notes show how path integral methods can be used in the theory of heavy ion reactions. The effects of internal degrees of freedom on the relative motion are contained in an influence functional which is calculated for several simple models of the internal structure. In each model the influence functional has a simple Gaussian structure which suggests that the relative motion of the nuclei in a deep inelastic collision can be described by a Langevin equation. The form of the influence functional determines the average damping force and the correlation function of the fluctuating Langevin force. (author)
Nonadiabatic effects in inelastic collisional processes
International Nuclear Information System (INIS)
Belyaev, Andrey K
2009-01-01
The standard adiabatic Born-Oppenheimer approach to inelastic collisional processes is revised. It is shown that the widely used standard interpretation of this approach has fundamental limitations leading to physical artefacts or to uncertainties in numerical calculations due to neglecting the electron translation problem. It is demonstrated that the Born-Oppenheimer approach itself does not have such limitations. The particular full quantum solution of the electron translation problem within the Born-Oppenheimer approach by means of the reprojection procedure is discussed in the paper together with the practical applications.
The theory of deeply inelastic scattering
International Nuclear Information System (INIS)
Bluemlein, J.
2012-01-01
The nucleon structure functions probed in deep-inelastic scattering at large virtualities form an important tool to test Quantum Chromdynamics (QCD) through precision measurements of the strong coupling constant α s (M Z 2 ) and the different parton distribution functions. The exact knowledge of these quantities is also of importance for all precision measurements at hadron colliders. During the last two decades very significant progress has been made in performing precision calculations. We review the theoretical status reached for both unpolarized and polarized lepton-hadron scattering based on perturbative QCD. (orig.)
Hadron final states in deep inelastic processes
International Nuclear Information System (INIS)
Bjorken, J.D.
1976-05-01
Lectures are presented dealing mainly with the description and discussion of hadron final states in electroproduction, colliding beams, and neutrino reactions from the point of view of the simple parton model. Also the space-time evolution of final states in the parton model is considered. It is found that the picture of space-time evolution of hadron final states in deep inelastic processes isn't totally trivial and that it can be made consistent with the hypotheses of the parton model. 39 references
Inelastic response spectra of simple degrading systems
International Nuclear Information System (INIS)
Andreaus, U.; Ceradini, G.; D'Asdia, P.; Gaudenzi, P.
1985-01-01
Ductility was first stated, for single-degree-of-freedom elastic-perfectly plastic systems as the ratio of maximum to yield displacements. An alternative approach, aimed to reduce design forces for ductile structures and based on the energy dissipated during earthquake allows to obtain more reliable ductility factors even when system restoring characteristics are affected by deterioration during loading history. Inelastic response of SDOF systems has been investigated under seimic excitation, assuming stable and degrading constitutive laws to model their structural behaviour. Energy spectra and ductility requirent diagrams are generated and compared with those of the corresponding elastic-perfectly plastic systems. (orig.)
Radiative corrections to deep inelastic muon scattering
International Nuclear Information System (INIS)
Akhundov, A.A.; Bardin, D.Yu.; Lohman, W.
1986-01-01
A summary is given of the most recent results for the calculaion of radiative corrections to deep inelastic muon-nucleon scattering. Contributions from leptonic electromagnetic processes up to the order a 4 , vacuum polarization by leptons and hadrons, hadronic electromagnetic processes approximately a 3 and γZ interference have been taken into account. The dependence of the individual contributions on kinematical variables is studied. Contributions, not considered in earlier calculations of radiative corrections, reach in certain kinematical regions several per cent at energies above 100 GeV
The theory of deeply inelastic scattering
Energy Technology Data Exchange (ETDEWEB)
Bluemlein, J.
2012-08-31
The nucleon structure functions probed in deep-inelastic scattering at large virtualities form an important tool to test Quantum Chromdynamics (QCD) through precision measurements of the strong coupling constant {alpha}{sub s}(M{sub Z}{sup 2}) and the different parton distribution functions. The exact knowledge of these quantities is also of importance for all precision measurements at hadron colliders. During the last two decades very significant progress has been made in performing precision calculations. We review the theoretical status reached for both unpolarized and polarized lepton-hadron scattering based on perturbative QCD. (orig.)
Micro-fresnel structures for microscopy of laser generated bright x-ray sources
International Nuclear Information System (INIS)
Ceglio, N.M.; Shavers, D.C.; Flanders, D.C.; Smith, H.I.
1979-01-01
A brief parametric survey of the x-ray characteristics of a gold micro-disk irradiated at 3 x 10 14 watt/cm 2 by a 1 nsec Nd-glass laser pulse has been provided as an example of a laser generated bright x-ray source. It was shown that a simple phenomenological model of the laser generated x-ray source as a microscopic equilibrium plasma radiating as a blackbody for a finite time determined by its hydrodynamic disassembly and radiation losses, serves to provide an adequate approximation to the x-ray characteristics of such sources. The current state of x-ray microscopy within the LLL laser fusion program was briefly reviewed. Kirpatrick--Baez grazing incidence reflection x-ray microscopes are being used to provide 3 to 5 μm resolution, broadband images (ΔE/E approx. 0.3) over a spectral range from .6 keV to 3.5 keV. Zone Plate Coded Imaging is used to provide 5 to 10 μm resolution, broadband (ΔE/E approx. 0.5) images over a spectral range from 3 keV to 50 keV. Efficient x-ray lensing elements with anticipated submicron resolution are being developed for narrowband (ΔE/E approx. 10 -2 ) imaging applications over a spectral range .1 keV to 8 keV. The x-ray lens design is that of a transmission blazed Fresnel phase plate. Micro--Fresnel zone plates with 3200 A minimum linewidth have been fabricated and preliminary resolution tests begun. The first resolution test pattern, having minimum linewidth of 2.5 μm, was imaged in lambda = 8.34 A light with no difficulty. Newer test patterns with submicron minimum line are being prepared for the next stage of resolution testing. An off-axis Fresnel zone plate with 1600 A minimum linewidth is presently being fabricated for use as an imaging spectrometer in order to provide spatially separated, chromatically distinct images of characteristic line emissions from laser fusion targets
International Nuclear Information System (INIS)
Montes, María J.; Barbero, Rubén; Abbas, Rubén; Rovira, Antonio
2016-01-01
Highlights: • A thermal model for a single-tube Fresnel receiver has been developed. • A comparative analysis based on different design parameters, has been carried out. • A comparative analysis based on different working fluids, has been carried out. • The receiver thermal performance is characterized by energy and exergy efficiencies. - Abstract: Although most of recent commercial Solar Thermal Power Plants (STPP) installed worldwide are parabolic trough plants, it seems that Linear Fresnel Collectors (LFC) are becoming an attractive option to generate electricity from solar radiation. Contrary to parabolic trough collectors, the design of LFC receivers has many degrees of freedom, and two basic designs can be found in the literature: single-tube and multi-tube design. This article studies the single-tube design, for which a thermal model has been developed. This model has been thought to be accurate enough to characterize the heat transfer in a non-elementary geometry and flexible enough to support changes of the characteristic parameters in the receiver design. The thermal model proposed is based on a two-dimensional, steady-state energy balance, in the receiver cross section and along its length. One of the features of the model is the characterization of the convective and radiative heat transfer in the receiver cavity, as it is not an elementary geometry. Another feature is the possibility of studying the receiver performance with different working fluids, both single-phase or two-phase. At last, the receiver performance has been characterized by means of the energy and exergy efficiency. Both variables are important for a complete receiver thermal analysis, as will be shown in the paper. The model has been first applied to the comparative study of the thermal performance of LFC receivers based on the value of some parameters: selective coating emissivity in the tube and inlet fluid thermal properties, for the case of using water/steam. As a second
Steady-state thermal analysis of an innovative receiver for linear Fresnel reflectors
International Nuclear Information System (INIS)
Abbas, R.; Muñoz, J.; Martínez-Val, J.M.
2012-01-01
Highlights: ► An innovative multitube receiver for linear Fresnel reflectors is presented. ► Higher performance is achieved thanks to better heat transfer conditions. ► A wide range of designs that maximize efficiency for different conditions is found. ► Heat transfer fluid inlet temperature must be lower for low radiation intensities. ► Fresnel performance may be close to trough collectors, with lower costs. -- Abstract: The study of the performance of an innovative receiver for linear Fresnel reflectors is carried out in this paper, and the results are analyzed with a physics perspective of the process. The receiver consists of a bundle of tubes parallel to the mirror arrays, resulting on a smaller cross section for the same receiver width as the number of tubes increases, due to the diminution of their diameter. This implies higher heat carrier fluid speeds, and thus, a more effective heat transfer process, although it conveys higher pumping power as well. Mass flow is optimized for different tubes diameters, different impinging radiation intensities and different fluid inlet temperatures. It is found that the best receiver design, namely the tubes diameter that maximizes the exergetic efficiency for given working conditions, is similar for the cases studied. There is a range of tubes diameters that imply similar efficiencies, which can drive to capital cost reduction thanks to the flexibility of design. In addition, the length of the receiver is also optimized, and it is observed that the optimal length is similar for the working conditions considered. As a result of this study, it is found that this innovative receiver provides an optimum design for the whole day, even though impinging radiation intensity varies notably. Thermal features of this type of receiver could be the base of a new generation of concentrated solar power plants with a great potential for cost reduction, because of the simplicity of the system and the lower weigh of the
Directory of Open Access Journals (Sweden)
Yasser A. Abdel-Hadi
2015-12-01
Full Text Available A new simulation model of a new solar pumped laser system was tested to be run in Helwan in Egypt (latitude φ = 29°52′N, longitude λ = 31°21′E and elevation = 141 m as an example of an industrial polluted area. The system is based on concentrating the solar radiation using a Fresnel lens on a laser head fixed on a mount tracking the sun during the day and powered by a DC battery. Two cases of this model are tested; the first one is the model consisting of a Fresnel lens and a two-dimensional Compound Parabolic Concentrator (CPC, while the other is the model consisting of a Fresnel lens and a three-dimensional Compound Parabolic Concentrator (CPC. The model is fed by real actual solar radiation data taken in Helwan Solar Radiation Station at NRIAG in the various seasons in order to know the laser power got from such a system in those conditions. For the system of Fresnel lens and 2D-CPC, an average laser output power of 1.27 W in Winter, 2 W in Spring, 5 W in Summer and 4.68 W in Autumn respectively can be obtained. Accordingly, the annual average output power for this system is 3.24 W. For the system of Fresnel lens and 3D-CPC, an average laser output power of 3.28 W in Winter, 3.55 W in Spring, 7.56 W in Summer and 7.13 W in Autumn respectively can be obtained. Accordingly, the annual average output power for this system is 5.38 W.
Inelastic neutron scattering and lattice dynamics of minerals
Indian Academy of Sciences (India)
We review current research on minerals using inelastic neutron scattering and lattice dynamics calculations. Inelastic neutron scattering studies in combination with first principles and atomistic calculations provide a detailed understanding of the phonon dispersion relations, density of states and their manifestations in ...
Inelastic neutron scattering and lattice dynamics of minerals
Indian Academy of Sciences (India)
Abstract. We review current research on minerals using inelastic neutron scattering and lattice dynamics calculations. Inelastic neutron scattering studies in combination with first principles and atomistic calculations provide a detailed understanding of the phonon dispersion relations, density of states and their ...
Slow electron contribution to inelastic reflection anisotropy
International Nuclear Information System (INIS)
Podsvirov, O.A.; Kuznetsov, Yu.A.
1980-01-01
Investigated is electron contribution with low energy (up to 1 keV) to the anisotropy of electron inelastic reflection (IRE) from silicon monocrystal (111) within 12-50 keV energy range of primary electrons. Experimental data on IRE anisotropy are presented: delay curves for silicon monocrystal, permitting to separate electrons with the energy up to 1 keV, dependences of IRE anisotropy on the energy of primary electrons for the systems - monocrystalline silicon-amorphous silicon film and delay curves for such systems (film thickness varies from 20 to 2000 A). Suggested is a phenomenologic model, permitting to take into account the contribution of slow electrons to IRE anisotropy: it is supposed, that three groups of electrons take part in the formation of the latter: elastic and inelastic reflected electrons, slow electrons, excited by primary electrons and slow electrons, generated by the reverse flow of the scattered electrons. Contribution of electrons, different by origin, to IRE anisotropy is evaluated in accordance with the experimental data on the basis of this model. It is stated, that slow electrons constitute approximately one half of the IRE anisotropy value, the contribution of both groups of slow electrons being approximately equal
Phenomenology of deep-inelastic processes
International Nuclear Information System (INIS)
Moretto, L.G.
1983-03-01
The field of heavy-ion deep-inelastic reactions is reviewed with particular attention to the experimental picture. The most important degrees of freedom involved in the process are identified and illustrated with relevant experiments. Energy dissipation and mass transfer are discussed in terms of particles and/or phonons exchanged in the process. The equilibration of the fragment neutron-to-proton ratios is inspected for evidence of giant isovector resonances. The angular momentum effects are observed in the fragment angular distributions and the angular momentum transfer is inferred from the magnitude and alignment of the fragments spins. The possible sources of light particles accompanying the deep-inelastic reactions are discussed. The use of the sequentially emitted particles as angular momentum probes is illustrated. The significance and uses of a thermalized component emitted by the dinucleus is reviewed. The possible presence of Fermi jets in the prompt component is shown to be critical to the justification of the one-body theories
The phenomenology of deep-inelastic processes
International Nuclear Information System (INIS)
Moretto, L.G.
1983-01-01
The field of heavy-ion deep-inelastic reactions is reviewed with particular attention to the experimental picture. The most important degrees of freedom involved in the process are identified and illustrated with relevant experiments. Energy dissipation and mass transfer are discussed in terms of particles and/or phonons exchanged in the process. The equilibration of the fragment neutron-to-proton ratios is inspected for evidence of giant isovector resonances. The angular momentum effects are observed in the fragment angular distributions and the angular momentum transfer is inferred from the magnitude and alignment of the fragments spins. The possible sources of light particles accompanying the deep-inelastic reactions are discussed. The use of the sequentially emitted particles as angular momentum probes is illustrated. The significance and uses of a thermalized component emitted by the dinucleus is reviewed. The possible presence of Fermi jets in the prompt component is shown to be critical to the justification of the one-body theories. (orig.)
Antinucleon-nucleus elastic and inelastic scattering
International Nuclear Information System (INIS)
Dover, C.B.; Millener, D.J.
1985-01-01
A general overview of the utility of antinucleon (anti N)-nucleus inelastic scattering studies is presented, emphasizing both the sensitivity of the cross sections to various components of the N anti N transition amplitudes and the prospects for the exploration of some novel aspects of nuclear structure. We start with an examination of the relation between NN and N anti N potentials, focusing on the coherences predicted for the central, spin-orbit and tensor components, and how these may be revealed by measurements of two-body spin observables. We next discuss the role of the nucleus as a spin and isospin filter, and show how, by a judicious choice of final state quantum numbers (natural or unnatural parity states, isospin transfer ΔT = 0 or 1) and momentum transfer q, one can isolate different components of the N anti N transition amplitude. Various models for the N anti N interaction which give reasonable fits to the available two-body data are shown to lead to strikingly different predictions for certain spin-flip nuclear transitions. We suggest several possible directions for future anti N-nucleus inelastic scattering experiments, for instance the study of spin observables which would be accessible with polarized anti N beams, charge exchange reactions, and higher resolution studies of the (anti p, anti p') reaction. We compare the antinucleon and the nucleon as a probe of nuclear modes of excitation. 40 refs., 13 figs
International Nuclear Information System (INIS)
Patino, A; Durand, P-E; Fogret, E; Pellat-Finet, P
2011-01-01
According to a scalar theory of diffraction, light propagation can be expressed by two-dimensional fractional order Fourier transforms. Since the fractional Fourier transform of a chirp function is a Dirac distribution, focusing a light beam is optically achieved by using a diffractive screen whose transmission function is a two-dimensional chirp function. This property is applied to designing Fresnel microlenses, and the orders of the involved Fourier fractional transforms depend on diffraction distances as well as on emitter and receiver radii of curvature. If the emitter is astigmatic (with two principal radii of curvature), the diffraction phenomenon involves two one-dimensional fractional Fourier transforms whose orders are different. This degree of freedom allows us to design microlenses that can focus astigmatic Gaussian beams, as produced by a line-shaped laser diode source.
Energy Technology Data Exchange (ETDEWEB)
Chemisana, Daniel, E-mail: daniel.chemisana@macs.udl.cat [Applied Physics Section of the Polytechnic School (EPS), University of Lleida, 25001 Lleida (Spain); Ignasi Rosell, Joan [Applied Physics Section of the Polytechnic School (EPS), University of Lleida, 25001 Lleida (Spain)
2011-09-15
Highlights: {yields} The designed concentrator has an important potential for building integration. {yields} The device concentrates radiation toward a static receiver. {yields} Tracking performed by a single driver, representing an important mechanical advantage. {yields} The system reaches a global optical efficiency value of 56.38%. - Abstract: A transmissive Fresnel reflector is designed to match the needs of building integration for concentrating photovoltaic (PV), thermal (T) or hybrid photovoltaic/thermal (PVT) generation. The device concentrates radiation toward a static receiver by means of an array of reflectors which rotate collectively. All rotation axes are coplanar and parallel. A deep analytical ray tracing study has been made of the design characteristics and concentrator performance, thus determining the configuration which optimises efficiency. Numerous ray tracing numerical simulations have been performed which contrast and support the analytical results.
International Nuclear Information System (INIS)
Chemisana, Daniel; Ignasi Rosell, Joan
2011-01-01
Highlights: → The designed concentrator has an important potential for building integration. → The device concentrates radiation toward a static receiver. → Tracking performed by a single driver, representing an important mechanical advantage. → The system reaches a global optical efficiency value of 56.38%. - Abstract: A transmissive Fresnel reflector is designed to match the needs of building integration for concentrating photovoltaic (PV), thermal (T) or hybrid photovoltaic/thermal (PVT) generation. The device concentrates radiation toward a static receiver by means of an array of reflectors which rotate collectively. All rotation axes are coplanar and parallel. A deep analytical ray tracing study has been made of the design characteristics and concentrator performance, thus determining the configuration which optimises efficiency. Numerous ray tracing numerical simulations have been performed which contrast and support the analytical results.
Development of Fresnel-based Concentrated Photovoltaic (CPV System with Uniform Irradiance
Directory of Open Access Journals (Sweden)
Irfan Ullah
2014-12-01
Full Text Available Different designs have been presented to achieve high concentration and uniformity for the concentrated photovoltaic (CPV system. Most of the designs have issues of low efficiency in terms of irradiance uniformity. To this end, we present a design methodology to increase irradiance uniformity over solar cell. The system consists of an eight-fold Fresnel lens as a primary optical element (POE and an optical lens, which consists of eight parts, as a secondary optical element (SOE. Sunlight is focused through the POE and then light is spread over cell through the SOE. In the design, maximum sunlight is passed over cell by minimizing losses. Results have shown that the proposed CPV design gives good irradiance uniformity. The concentration module based on this novel design is a promising option for the development of a cost-effective photovoltaic solar energy generation.
Zoschke, Theda; Seubert, Bernhard; Fluri, Thomas
2017-06-01
An existing linear Fresnel power plant with ORC process located in Ben Guerir, Morocco, is retrofitted with a thermal energy storage system and additional collector loops. Two different plant configurations are investigated in this paper. In the first configuration two separate solar fields are built and only the minor one can charge the storage. In the second configuration, there is only one large solar field which offers more flexibility. Two different control strategies are assessed by comparing simulation results. It shows that the simulations of the systems with two solar fields results in higher energy yields throughout the year, but the power production of the system with one solar field is much more flexible and demand oriented. Also it offers great potential for improvement when it comes to weather forecasting.
Fringe-tunable electrothermal Fresnel mirror for use in compact and high-speed diffusion sensor.
Kiuchi, Yuki; Taguchi, Yoshihiro; Nagasaka, Yuji
2017-01-23
This paper reports the development of an electrothermal microelectromechanical systems (MEMS) mirror with serpentine shape actuators. A micro Fresnel mirror with fringe-spacing tunability is required to realize a compact and high-speed diffusion sensor for biological samples whose diffusion coefficient changes significantly because of a conformational change. In this case, the measurement time-constant is dependent on the fringe-spacing and diffusion coefficient of the sample. In this study, a fringe-tunable MEMS mirror with an actuation voltage less than 10 V was developed. The characteristics of the fabricated mirror were investigated experimentally. A high-visibility optical interference fringe was successfully demonstrated using both an ultranarrow-linewidth solid-state laser and a low-cost compact laser diode. The experimental results demonstrated a distinct possibility of developing a measurement device using only simple and low-voltage optical components.
Generation of Binary Off-axis Digital Fresnel Hologram with Enhanced Quality
Directory of Open Access Journals (Sweden)
Peter Wai Ming Tsang
2015-06-01
Full Text Available The emergence of high resolution printer and digital micromirror device (DMD has enabled real, off-axis holograms to be printed, or projected onto a screen. As most printers and DMD can only reproduce binary dots, the pixels in a hologram have to be truncated to 2 levels. However, direct binarizing a hologram will lead to severe degradation on its reconstructed image. In this paper, a method for generating binary off-axis digital Fresnel hologram is reported. A hologram generated with the proposed method is referred to as the "Enhanced Sampled Binary Hologram" (ESBH. The reconstructed image of the ESBH is superior in visual quality as compare with the one obtained with existing technique, and also resistant to noise contamination.
Optical image encryption using fresnel zone plate mask based on fast walsh hadamard transform
Khurana, Mehak; Singh, Hukum
2018-05-01
A new symmetric encryption technique using Fresnel Zone Plate (FZP) based on Fast Walsh Hadamard Transform (FWHT) is proposed for security enhancement. In this technique, bits of plain image is randomized by shuffling the bits randomly. The obtained scrambled image is then masked with FZP using symmetric encryption in FWHT domain to obtain final encrypted image. FWHT has been used in the cryptosystem so as to protect image data from the quantization error and for reconstructing the image perfectly. The FZP used in proposed scheme increases the key space and makes it robust to many traditional attacks. The effectiveness and robustness of the proposed cryptosystem has been analyzed on the basis of various parameters by simulating on MATLAB 8.1.0 (R2012b). The experimental results are provided to highlight suitability of the proposed cryptosystem and prove that the system is secure.
Hennelly, Bryan M.; Sheridan, John T.
2005-05-01
By use of matrix-based techniques it is shown how the space-bandwidth product (SBP) of a signal, as indicated by the location of the signal energy in the Wigner distribution function, can be tracked through any quadratic-phase optical system whose operation is described by the linear canonical transform. Then, applying the regular uniform sampling criteria imposed by the SBP and linking the criteria explicitly to a decomposition of the optical matrix of the system, it is shown how numerical algorithms (employing interpolation and decimation), which exhibit both invertibility and additivity, can be implemented. Algorithms appearing in the literature for a variety of transforms (Fresnel, fractional Fourier) are shown to be special cases of our general approach. The method is shown to allow the existing algorithms to be optimized and is also shown to permit the invention of many new algorithms.
Energy Technology Data Exchange (ETDEWEB)
Herrero, R.; Miller, D. C.; Kurtz, S. R.; Anton, I.; Sala, G.
2013-07-01
A system dedicated to the optical transmittance characterization of Fresnel lenses has been developed at NREL, in collaboration with the UPM. The system quantifies the optical efficiency of the lens by generating a performance map. The shape of the focused spot may also be analyzed to understand change in the lens performance. The primary instrument components (lasers and CCD detector) have been characterized to confirm their capability for performing optical transmittance measurements. Measurements performed on SoG and PMMA lenses subject to a variety of indoor conditions (e.g., UV and damp heat) identified differences in the optical efficiency of the evaluated lenses, demonstrating the ability of the Scanning Lens Instrument (SLI) to distinguish between the aged lenses.
Development of a high-resolution electron-beam profile monitor using Fresnel zone plates
International Nuclear Information System (INIS)
Nakamura, Norio; Sakai, Hiroshi; Muto, Toshiya; Hayano, Hitoshi
2004-01-01
We present a high-resolution and real-time beam profile monitor using Fresnel zone plates (FZPs) developed in the KEK-ATF damping ring. The monitor system has an X-ray imaging optics with two FZPs. In this monitor, the synchrotron radiation from the electron beam at the bending magnet is monochromatized by a crystal monochromator and the transverse electron beam image is twenty-times magnified by the two FZPs and detected on an X-ray CCD camera. The expected spatial resolution for the selected photon energy of 3.235 keV is less than 1 μm. With the beam profile monitor, we succeeded in obtaining a clear electron-beam image and measuring the extremely small beam size less than 10 μm. It is greatly expected that the beam profile monitor will be used in high-brilliance light sources and low-emittance accelerators. (author)
Damage-induced nonassociated inelastic flow in rock salt
International Nuclear Information System (INIS)
Chan, K.S.; Bodner, S.R.; Brodsky, N.S.; Fossum, A.F.; Munson, D.E.
1993-01-01
The multi-mechanism deformation coupled fracture model recently developed by CHAN, et al. (1992), for describing time-dependent, pressure-sensitive inelastic flow and damage evolution in crystalline solids was evaluated against triaxial creep experiments on rock salt. Guided by experimental observations, the kinetic equation and the flow law for damage-induced inelastic flow in the model were modified to account for the development of damage and inelastic dilatation in the transient creep regime. The revised model was then utilized to obtain the creep response and damage evolution in rock salt as a function of confining pressure and stress difference. Comparison between model calculation and experiment revealed that damage-induced inelastic flow is nonassociated, dilatational, and contributes significantly to the macroscopic strain rate observed in rock salt deformed at low confining pressures. The inelastic strain rate and volumetric strain due to damage decrease with increasing confining pressures, and all are suppressed at sufficiently high confining pressures
Optical-CT 3D Dosimetry Using Fresnel Lenses with Minimal Refractive-Index Matching Fluid.
Directory of Open Access Journals (Sweden)
Steven Bache
Full Text Available Telecentric optical computed tomography (optical-CT is a state-of-the-art method for visualizing and quantifying 3-dimensional dose distributions in radiochromic dosimeters. In this work a prototype telecentric system (DFOS-Duke Fresnel Optical-CT Scanner is evaluated which incorporates two substantial design changes: the use of Fresnel lenses (reducing lens costs from $10-30K t0 $1-3K and the use of a 'solid tank' (which reduces noise, and the volume of refractively matched fluid from 1 ltr to 10 cc. The efficacy of DFOS was evaluated by direct comparison against commissioned scanners in our lab. Measured dose distributions from all systems were compared against the predicted dose distributions from a commissioned treatment planning system (TPS. Three treatment plans were investigated including a simple four-field box treatment, a multiple small field delivery, and a complex IMRT treatment. Dosimeters were imaged within 2 h post irradiation, using consistent scanning techniques (360 projections acquired at 1 degree intervals, reconstruction at 2mm. DFOS efficacy was evaluated through inspection of dose line-profiles, and 2D and 3D dose and gamma maps. DFOS/TPS gamma pass rates with 3%/3mm dose difference/distance-to-agreement criteria ranged from 89.3% to 92.2%, compared to from 95.6% to 99.0% obtained with the commissioned system. The 3D gamma pass rate between the commissioned system and DFOS was 98.2%. The typical noise rates in DFOS reconstructions were up to 3%, compared to under 2% for the commissioned system. In conclusion, while the introduction of a solid tank proved advantageous with regards to cost and convenience, further work is required to improve the image quality and dose reconstruction accuracy of the new DFOS optical-CT system.
International Nuclear Information System (INIS)
Bellos, Evangelos; Mathioulakis, Emmanouil; Tzivanidis, Christos; Belessiotis, Vassilis; Antonopoulos, Kimon A.
2016-01-01
Highlights: • A linear Fresnel solar collector with flat plate receiver is investigated. • The collector is investigated experimentally in energetic and exergetic terms. • The developed numerical model is validated with the experimental results. • The operation with thermal oil is also examined with the developed model. • The final results prove satisfying performance for medium temperature levels. - Abstract: In this study a linear Fresnel solar collector with flat plate receiver is investigated experimentally and numerically with Solidworks Flow Simulation. The developed model combines optical, thermal and flow analysis; something innovative and demanding which leads to accurate results. The main objective of this study is to determine the thermal, the optical and the exergetic performance of this collector in various operating conditions. For these reasons, the developed model is validated with the respective experimental data and after this step, the solar collector model is examined parametrically for various fluid temperature levels and solar incident angles. The use of thermal oil is also analyzed with the simulation tool in order to examine the collector performance in medium temperature levels. The experiments are performed with water as working fluid and for low temperature levels up to 100 °C. The final results proved that this solar collector is able to produce about 8.5 kW useful heat in summer, 5.3 kW in spring and 2.9 kW in winter. Moreover, the operation of this collector with thermal oil can lead to satisfying results up to 250 °C.
International Nuclear Information System (INIS)
Moretto, L.G.
1979-03-01
The collective modes excited in deep-inelastic reactions and their natural hierarchy provided by their characteristic relaxation times is described. The relaxation of the mass asymmetry mode is discussed in terms of a diffusion process. Charge distributions and angular distributions as a function of Z calculated with this model are in good agreement with experimental data. This diffusion model also treats the transfer of energy and angular momentum in terms of particle transfer, and is successfully compared with experimental γ-ray multiplicities as a function of both Q-value and mass asymmetry. The angular momentum transfer is again considered in connection with the sequential fission of heavy, deep-inelastic fragments and the excitation of collective modes in the exit channel is considered. The role of the giant E1 mode in the equilibration of the neutron-to-proton ratio is discussed. 39 references
Current fragmentation in deep inelastic scattering
International Nuclear Information System (INIS)
Hamer, C.J.
1975-04-01
It is argued that the current fragmentation products in deep inelastic electron scattering will not be distributed in a 'one-dimensional' rapidity plateau as in the parton model picture of Feynman and Bjorken. A reaction mechanism with a multiperipheral topology, but which the above configuration might have been achieved, does not in fact populate the current fragmentation plateau; and unless partons are actually observed in the final state, it cannot lead to Bjorken scaling. The basic reason for this failure is shown to be the fact that when a particle is produced in the current fragmentation plateau, the adjacent momentum transfer in the multiperipheral chain becomes large and negative: such processes are inevitably suppressed. Instead, the current fragmentation products are likely to be generated by a fragmentation, or sequential decay process. (author)
πN inelastic reaction index, 1977
International Nuclear Information System (INIS)
Kawaguchi, Masaaki; Kichimi, Hiromichi; Oyanagi, Yoshio; Sugahara, Ryuhei; Takahashi, Kasuke.
1977-08-01
This report prepared by the KEK-PDG (Particle Data Group of the National Laboratory for High Energy Physics, Ibaraki, Japan) is a document compilation which covers 298 literatures dealing with πN inelastic reactions which were published in either of the following journals in the years of 1974, 1975 and 1976: Nuovo Cimento, Nuovo Cimento Letters, Nuclear Physics, Physics Letters, Physical Review, Physical Review Letters, Soviet Journal of Nuclear Physics and JETP Letters. Five indices are also given to facilitate the use of this compilation. Almost all the pages of this report is devoted to the listing of the five indices (accelerator, detector, reaction, beam momentum, and data description indices). In the appendix, some abbreviations for accelerators, detectors, institutions, and particles are listed. The descriptors for reaction data, and for particle properties, and beam momentum designations are also listed in the appendix. (Aoki, K.)
Statistical properties of deep inelastic reactions
International Nuclear Information System (INIS)
Moretto, L.G.
1983-08-01
The multifaceted aspects of deep-inelastic heavy-ion collisions are discussed in terms of the statistical equilibrium limit. It is shown that a conditional statistical equilibrium, where a number of degrees of freedom are thermalized while others are still relaxing, prevails in most of these reactions. The individual degrees of freedom that have been explored experimentally are considered in their statistical equilibrium limit, and the extent to which they appear to be thermalized is discussed. The interaction between degrees of freedom on their way towards equilibrium is shown to create complex feedback phenomena that may lead to self-regulation. A possible example of self-regulation is shown for the process of energy partition between fragments promoted by particle exchange. 35 references
Nonlinear continuum mechanics and large inelastic deformations
Dimitrienko, Yuriy I
2010-01-01
This book provides a rigorous axiomatic approach to continuum mechanics under large deformation. In addition to the classical nonlinear continuum mechanics - kinematics, fundamental laws, the theory of functions having jump discontinuities across singular surfaces, etc. - the book presents the theory of co-rotational derivatives, dynamic deformation compatibility equations, and the principles of material indifference and symmetry, all in systematized form. The focus of the book is a new approach to the formulation of the constitutive equations for elastic and inelastic continua under large deformation. This new approach is based on using energetic and quasi-energetic couples of stress and deformation tensors. This approach leads to a unified treatment of large, anisotropic elastic, viscoelastic, and plastic deformations. The author analyses classical problems, including some involving nonlinear wave propagation, using different models for continua under large deformation, and shows how different models lead t...
Inelastic Neutron Scattering Study of Mn
Energy Technology Data Exchange (ETDEWEB)
Zhong, Y.; Sarachik, M.P.; Friedman, J.R.; Robinson, R.A.; Kelley, T.M.; Nakotte, H.; Christianson, A.C.; Trouw, F.; Aubin, S.M.J.; Hendrickson, D.N.
1998-11-09
The authors report zero-field inelastic neutron scattering experiments on a 14-gram deuterated sample of Mn{sub 12}-Acetate consisting of a large number of identical spin-10 magnetic clusters. Their resolution enables them to see a series of peaks corresponding to transitions between the anisotropy levels within the spin-10 manifold. A fit to the spin Hamiltonian H = {minus}DS{sub z}{sup 2} + {mu}{sub B}B{center_dot}g{center_dot}S-BS{sub z}{sup 4} + C(S{sub +}{sup 4} + S{sub {minus}}{sup 4}) yields an anisotropy constant D = (0.54 {+-} 0.02) K and a fourth-order diagonal anisotropy coefficient B = (1.2 {+-} 0.1) x 10{sup {minus}3}K. Unlike EPR measurements, their experiments do not require a magnetic field and yield parameters that do not require knowledge of the g-value.
Neutron Inelastic Scattering Study of Liquid Argon
Energy Technology Data Exchange (ETDEWEB)
Skoeld, K; Rowe, J M; Ostrowski, G [Solid State Science Div., Argonne National Laboratory, Argonne, Illinois (US); Randolph, P D [Nuclear Technology Div., Idaho Nuclear Corporation, Idaho Falls, Idaho (US)
1972-02-15
The inelastic scattering functions for liquid argon have been measured at 85.2 K. The coherent scattering function was obtained from a measurement on pure A-36 and the incoherent function was derived from the result obtained from the A-36 sample and the result obtained from a mixture of A-36 and A-40 for which the scattering is predominantly incoherent. The data, which are presented as smooth scattering functions at constant values of the wave vector transfer in the range 10 - 44/nm, are corrected for multiple scattering contributions and for resolution effects. Such corrections are shown to be essential in the derivation of reliable scattering functions from neutron scattering data. The incoherent data are compared to recent molecular dynamics results and the mean square displacement as a function of time is derived. The coherent data are compared to molecular dynamics results and also, briefly, to some recent theoretical models
Excitation of giant resonances through inelastic scattering
International Nuclear Information System (INIS)
Kailas, S.
1981-01-01
In the last few years, exciting developments have taken place in the study of giant resonances (GR). In addition to the already well known gjant dipole resonance (GDR), the presence of at least two more new GRs viz. giant quadrupole resonance (GQR) and giant monopole resonance (GMR) has been experimentally established. The systematics covering these GRs is found to be consistent with the theoretical expectation. Though the existence of higher multipoles has been predjcted by theory, so far only some of these have been found to be excited experimentally. Various probe particles - electrons, protons (polarized and unpolarized), light and heavy ions and pions - at different bombarding energies have been used to excite the GR region, primarily through the inelastic scattering process. Detailed experiments, looking at the decay modes of GR region, have also been performed. These studies have contributed significantly to a better understanding of the phenomenon of nuclear collective excitation. In this report, the current status of 'GR' research is reviewed. (author)
Shadowing in inelastic lepton-deuteron scattering
International Nuclear Information System (INIS)
Badelek, B.
1992-01-01
Shadowing in inelastic lepton-deuteron scattering is analysed using the double interaction formalism where we relate shadowing to inclusive diffractive processes. Both the vector meson and parton contributions are considered for low and high Q 2 values including QCD corrections with parton recombination for high Q 2 . These Q 2 values were chosen to correspond to existing experimental data and to the possible HERA measurements. Detailed discussion of various shadowing mechanisms is given. As expected the shadowing effects are found to be very small, less then 2% or so, in agreement with the recent precise measurements performed by the New Muon Collaboration. The contribution of shadowing term to the Gottfried sum the region x > 0.004 and for Q 2 = 4 GeV 2 is estimated to be equal to -0.025. (author). 10 refs, 4 figs
Boson structure functions from inelastic electron scattering
International Nuclear Information System (INIS)
De Jager, C.W.
1986-01-01
The even /sup 104-110/Pd isotopes and /sup 196/Pt have been investigated at NIKHEF-K by high-resolution inelastic electron scattering. A new IBA-2 calculation has been performed for the Pd isotopes, in which the ratio of the proton and neutron coupling constants is taken from pion scattering. One set of boson structure functions sufficed for the description of the first and second E2-excitations in all Pd isotopes. The data showed no sensitivity for different structure functions for proton and neutron bosons. A preliminary analysis of a number of negative parity states (3/sup -/,5/sup -/ and 7/sup -/), observed in /sup 196/Pt, was performed through the introduction of an f-boson. The first E4-excitation in the palladium isotopes can be reasonably described with a β-structure function, but all other E4-excitations require the introduction of g-boson admixtures
Inelastic response of silicon to shock compression.
Higginbotham, A; Stubley, P G; Comley, A J; Eggert, J H; Foster, J M; Kalantar, D H; McGonegle, D; Patel, S; Peacock, L J; Rothman, S D; Smith, R F; Suggit, M J; Wark, J S
2016-04-13
The elastic and inelastic response of [001] oriented silicon to laser compression has been a topic of considerable discussion for well over a decade, yet there has been little progress in understanding the basic behaviour of this apparently simple material. We present experimental x-ray diffraction data showing complex elastic strain profiles in laser compressed samples on nanosecond timescales. We also present molecular dynamics and elasticity code modelling which suggests that a pressure induced phase transition is the cause of the previously reported 'anomalous' elastic waves. Moreover, this interpretation allows for measurement of the kinetic timescales for transition. This model is also discussed in the wider context of reported deformation of silicon to rapid compression in the literature.
Mass corrections in deep-inelastic scattering
International Nuclear Information System (INIS)
Gross, D.J.; Treiman, S.B.; Wilczek, F.A.
1977-01-01
The moment sum rules for deep-inelastic lepton scattering are expected for asymptotically free field theories to display a characteristic pattern of logarithmic departures from scaling at large enough Q 2 . In the large-Q 2 limit these patterns do not depend on hadron or quark masses m. For modest values of Q 2 one expects corrections at the level of powers of m 2 /Q 2 . We discuss the question whether these mass effects are accessible in perturbation theory, as applied to the twist-2 Wilson coefficients and more generally. Our conclusion is that some part of the mass effects must arise from a nonperturbative origin. We also discuss the corrections which arise from higher orders in perturbation theory for very large Q 2 , where mass effects can perhaps be ignored. The emphasis here is on a characterization of the Q 2 , x domain where higher-order corrections are likely to be unimportant
Energy Technology Data Exchange (ETDEWEB)
Pichet-Thomasset, M
1999-07-01
The goal of this work is to study the capabilities of imaging of Fresnel zone plates in the 1.5. and 2 keV X-ray range for the imaging of laser-produced plasmas. The diagnostic is composed of a Fresnel zone plate with good imaging capabilities and a multilayer mirror to select the spectral emission bandwidth of the plasma we want to study. This diagnostic was evaluated at the Centre d'Etudes de Limeil-Valenton experiments to study spatial resolution with this kind of X-ray source. The images we obtained showed that there is no geometric aberrations over an object field of several millimetre. Fresnen zone plates are often used for monochromatic biological objects imaging in the water window around 400 eV but they offer large prospects for laser produced plasma imaging. (author)
A multislice theory of electron inelastic scattering in a solid
International Nuclear Information System (INIS)
Wang, Z.L.
1989-01-01
A multislice theory is proposed to solve Yoshioka's coupling equations for elastic and inelastic scattered high-energy electrons in a solid. This method is capable, in principle, of including the non-periodic crystal structures and the electron multiple scattering among all the excited states in the calculations. It is proved that the proposed theory for calculating the energy-filtered inelastic images, based on the physical optics approach, is equivalent to the quantum-mechanical theory under some approximations. The basic theory of simulating the energy-filtered inelastic image of core-shell losses and thermal diffuse scattering is outlined. (orig.)
Compton profiles by inelastic ion-electron scattering
International Nuclear Information System (INIS)
Boeckl, H.; Bell, F.
1983-01-01
It is shown that Compton profiles (CP) can be measured by inelastic ion-electron scattering. Within the impulse approximation the binary-encounter peak (BEP) reflects the CP of the target atom whereas the electron-loss peak (ELP) is given by projectile CP's. Evaluation of experimental data reveals that inelastic ion-electron scattering might be a promising method to supply inelastic electron or photon scattering for the determination of target CP's. The measurement of projectile CP's is unique to ion scattering since one gains knowledge about wave-function effects because of the high excitation degree of fast heavy-ion projectiles
New statistical model of inelastic fast neutron scattering
International Nuclear Information System (INIS)
Stancicj, V.
1975-07-01
A new statistical model for treating the fast neutron inelastic scattering has been proposed by using the general expressions of the double differential cross section in impuls approximation. The use of the Fermi-Dirac distribution of nucleons makes it possible to derive an analytical expression of the fast neutron inelastic scattering kernel including the angular momenta coupling. The obtained values of the inelastic fast neutron cross section calculated from the derived expression of the scattering kernel are in a good agreement with the experiments. A main advantage of the derived expressions is in their simplicity for the practical calculations
Development of inelastic design method for liquid metal reactor plants
International Nuclear Information System (INIS)
Takahashi, Yukio; Take, Kohji; Kaguchi, Hitoshi; Fukuda, Yoshio; Uno, Tetsuro.
1991-01-01
Effective utilization of inelastic analysis in structural design assessment is expected to play an important role for avoiding too conservative design of liquid metal reactor plants. Studies have been conducted by the authors to develop a guideline for application of detailed inelastic analysis in design assessment. Both fundamental material characteristics tests and structural failure tests were conducted. Fundamental investigations were made on inelastic analysis method and creep-fatigue life prediction method based on the results of material characteristics tests. It was demonstrated through structural failure tests that the design method constructed based on these fundamental investigations can predict failure lives in structures subjected to cyclic thermal loadings with sufficient accuracy. (author)
Average multiplications in deep inelastic processes and their interpretation
International Nuclear Information System (INIS)
Kiselev, A.V.; Petrov, V.A.
1983-01-01
Inclusive production of hadrons in deep inelastic proceseseus is considered. It is shown that at high energies the jet evolution in deep inelastic processes is mainly of nonperturbative character. With the increase of a final hadron state energy the leading contribution to an average multiplicity comes from a parton subprocess due to production of massive quark and gluon jets and their further fragmentation as diquark contribution becomes less and less essential. The ratio of the total average multiplicity in deep inelastic processes to the average multiplicity in e + e - -annihilation at high energies tends to unity
Directory of Open Access Journals (Sweden)
Giuseppe Mazzarella
2012-01-01
Full Text Available In this paper we propose a new holographic procedure for the diagnostic of large reflector antennas, based on the direct use of the Fresnel-field pattern. The relation leading from the Fresnel field to the current on the reflector surface is formulated in the least-squares sense as a discrete data inverse problem and then regularized by using a singular value decomposition approach. A detailed theoretical analysis of the problem and full assessment of the presented technique are provided. Simulations are carried out by using the radiative near-field pattern generated with a commercial software. Results show good accuracy and robustness to noise for the retrieval of the panel-to-panel misalignment of a reflector antenna.
First light of an external occulter testbed at flight Fresnel numbers
Kim, Yunjong; Sirbu, Dan; Hu, Mia; Kasdin, Jeremy; Vanderbei, Robert J.; Harness, Anthony; Shaklan, Stuart
2017-01-01
Many approaches have been suggested over the last couple of decades for imaging Earth-like planets. One of the main candidates for creating high-contrast for future Earth-like planets detection is an external occulter. The external occulter is a spacecraft flown along the line-of-sight of a space telescope to suppress starlight and enable high-contrast direct imaging of exoplanets. The occulter is typically tens of meters in diameter and the separation from the telescope is of the order of tens of thousands of kilometers. Optical testing of a full-scale external occulter on the ground is impossible because of the long separations. Therefore, laboratory verification of occulter designs is necessary to validate the optical models used to design and predict occulter performance. At Princeton, we have designed and built a testbed that allows verification of scaled occulter designs whose suppressed shadow is mathematically identical to that of space occulters. The goal of this experiment is to demonstrate a pupil plane suppression of better than 1e-9 with a corresponding image plane contrast of better than 1e-11. The occulter testbed uses a 77.2 m optical propagation distance to realize the flight Fresnel number of 14.5. The scaled mask is placed at 27.2 m from the artificial source and the camera is located 50.0 m from the scaled mask. We will use an etched silicon mask, manufactured by the Microdevices Lab(MDL) of the Jet Propulsion Laboratory(JPL), as the occulter. Based on conversations with MDL, we expect that 0.5 μm feature size is an achievable resolution in the mask manufacturing process and is therefore likely the indicator of the best possible performance. The occulter is illuminated by a diverging laser beam to reduce the aberrations from the optics before the occulter. Here, we present first light result of a sample design operating at a flight Fresnel number and the experimental setup of the testbed. We compare the experimental results with simulations
International Nuclear Information System (INIS)
Ledermann, P.; Escatha, Y. d'.
1981-01-01
At elevated temperature, ASME CODE CASE N 47 demands, in its design and analysis part to demonstrate that none of eight damages, related to the monotonic and cyclic inelastic behaviour of the material and structure, will happen during the whole life of the reactor. However this demonstration, for strain limits and creep fatigue failure, using a purely elastic analysis as in the ASME CODE Section III, is usually impossible. Inelastic analysis is then necessary. We review some of the research work (theorical and experimental) which is being done to qualify methods for an inelastic analysis of structures at elevated temperature [fr
Electron Dynamics by Inelastic X-Ray Scattering
Schülke, Winfried
2007-01-01
The book offers the first comprehensive review of experimental methods, theory, and successful applications of synchrotron radiation based inelastic X-ray scattering (IXS) spectroscopy, which enables the investigation of electron dynamics in condensed matter (correlated motion and excitation).
Photoproduction of Inelastic and Elastic $J/\\psi$ Vector Mesons
Energy Technology Data Exchange (ETDEWEB)
Stundzia, Audrius Bronius [Toronto U.
1992-06-01
Results and analysis on the inelastic and elastic photoproduction of $J /\\psi$ vector mesons by Fermilab experiment E691 are presented. The inelastic, deep inelastic, coherent elastic and incoherent elastic cross sections were measured at ($E_{\\gamma}$) = 145 GeV. The $d\\sigma / dzdp^2_{\\tau}$} distribution and the photon energy dependence of the cross sections for these production processes were also measured. The deep inelastic $J /\\psi$ was analyzed in the colour-singlet photon-gluon-fusion model. It was found that the $d\\sigma / dzdp^2_{\\tau}$ distribution and the the rise of the cross section with $E\\gamma$ are both well described by a relatively soft gluon distribution [xG( x) $\\alpha$ ($1 - x )^{ng}$, where $n_g$ = 6.5 ± 1.1 (stat.)$^{+1.0}_{-0.6}$(syst.)].
Comparison study of inelastic analysis codes for high temperature structure
Energy Technology Data Exchange (ETDEWEB)
Kim, Jong Bum; Lee, H. Y.; Park, C. K.; Geon, G. P.; Lee, J. H
2004-02-01
LMR high temperature structures subjected to operating and transient loadings may exhibit very complex deformation behaviors due to the use of ductile material such as 316SS and the systematic analysis technology of high temperature structure for reliable safety assessment is essential. In this project, comparative study with developed inelastic analysis program NONSTA and the existing analysis codes was performed applying various types of loading including non-proportional loading. The performance of NONSTA was confirmed and the effect of inelastic constants on the analysis result was analyzed. Also, the applicability of the inelastic analysis was enlarged as a result of applying both the developed program and the existing codes to the analyses of the enhanced creep behavior and the elastic follow-up behavior of high temperature structures and the necessary items for improvements were deduced. Further studies on the improvement of NONSTA program and the decision of the proper values of inelastic constants are necessary.
Sterman-Weinberg formula in deep inelastic scattering
International Nuclear Information System (INIS)
Dzhaparidze, G.Sh.; Kartvelishvili, V.G.
1981-01-01
The jet cross-section in current fragmentation region in deep inelastic scattering is obtained. It is shown that this jet produced in ep reaction is narrower, then the one from e + e - -annihilation [ru
Analysis of partial and total inelasticities obtained from inclusive reactions
International Nuclear Information System (INIS)
Bellandi, J.; Covolan, R.; Costa, C.G.; Montanha, J.; Mundim, L.M.
1994-01-01
An independent analysis of model for energetic dependence on inelasticity is presented, from experimental data of pp → c X (c = π +- , Κ +- , p +- ) type inclusive reactions. 6 refs., 2 figs., 1 tab
Analysis of inelastic neutron scattering results on model compounds ...
Indian Academy of Sciences (India)
Vibrational spectroscopy; nitrogenous bases; inelastic neutron scattering. PACS No. ... obtain good quality, high resolution results in this region. Here the .... knowledge of the character of each molecular transition as well as the calculated.
Inelastic scattering to collective states in double-magic nuclei
International Nuclear Information System (INIS)
Wambach, J.
1979-06-01
The paper discusses several aspects of inelastic scattering to collective states in the framework of the 'Shell Model RPA Approximation' with special emphasis on the analysis of giant resonance states. (orig./WL) [de
Expansions for model-independent analyses of inelastic electron scattering
International Nuclear Information System (INIS)
Jackson, D.F.; Hilton, J.M.; Roberts, A.C.M.
1977-01-01
It is noted that the commonly-used Fourier-Bessel expansion for the transition density for inelastic electron scattering depends sensitively on an arbitrary parameter and is not realistic at large distances. Alternative expansions are suggested. (author)
Structure functions in electron-nucleon deep inelastic scattering
Energy Technology Data Exchange (ETDEWEB)
Saleem, M.; Fazal-E-Aleem (University of the Punjab, Lahore (Pakistan). Dept. of Physics)
1982-06-26
The phenomenological expressions for the structure functions in electron-nucleon deep inelastic scattering are proposed and are shown to satisfy the experimental data as well as a number of sum rules.
Multiple production of hadrons in deep inelastic processes
International Nuclear Information System (INIS)
Kiselev, A.V.; Petrov, V.A.
1985-01-01
Formulas are proposed for the description of the mean multiplicity of hadrons in deep inelastic processes. On the basis of the existing data, predictions are made for the behavior of the mean multiplicity at higher energies
Dissipative phenomena in deep inelastic heavy ion collisions
International Nuclear Information System (INIS)
Gross, D.H.E.; Krappe, H.J.; Lindenberger, K.H.; Lipperheide, R.; Moehring, K.
1978-01-01
During this meeting the following theoretical concepts for deep-inelastic heavy ion reactions were discussed: the energy transfer and friction, direct or statistical mechanisms, dissipation and fluctuation. (WL) [de
Deep inelastic lepton scattering from nucleons and nuclei
International Nuclear Information System (INIS)
Berger, E.L.
1986-02-01
A pedagogical review is presented of results obtained from inclusive deep inelastic scattering of leptons from nucleons and nuclei, with particular emphasis on open questions to be explored in future experiments
Deeply inelastic scattering at small x in 20 min
International Nuclear Information System (INIS)
Levin, E.M.
1992-01-01
A status report is presented on new phenomena that are anticipated in deeply inelastic scattering in the low x→0 region. A summary of the theoretical situation in the region of small x is given, including the importance for the understanding of high energy interaction in QCD, and the low x behaviour of deep inelastic structure function. This new area of physics will be studied experimentally at HERA. (R.P.) 16 refs.; 6 figs
Inelastic Boosted Dark Matter at direct detection experiments
Giudice, Gian F.; Kim, Doojin; Park, Jong-Chul; Shin, Seodong
2018-01-01
We explore a novel class of multi-particle dark sectors, called Inelastic Boosted Dark Matter (iBDM). These models are constructed by combining properties of particles that scatter off matter by making transitions to heavier states (Inelastic Dark Matter) with properties of particles that are produced with a large Lorentz boost in annihilation processes in the galactic halo (Boosted Dark Matter). This combination leads to new signals that can be observed at ordinary direct detection experimen...
Inelastic dark matter at DAMA, CDMS and Future Experiments
Smith, David R.; Weiner, Neal
2002-01-01
The DAMA annual modulation signature, interpreted as evidence for a spin-independent WIMP coupling, seems in conflict with null results from CDMS. However, in models of ``inelastic dark matter'', the experiments are compatible. Inelastic dark matter can arise in supersymmetric theories as the real component of a sneutrino mixed with a singlet scalar. In contrast with ordinary sneutrino dark matter, such particles can satisfy all experimental constraints while giving the appropriate relic abun...
Theory of time-resolved inelastic x-ray diffraction
DEFF Research Database (Denmark)
Lorenz, Ulf; Møller, Klaus Braagaard; Henriksen, Niels Engholm
2010-01-01
Starting from a general theory of time-resolved x-ray scattering, we derive a convenient expression for the diffraction signal based on a careful analysis of the relevant inelastic scattering processes. We demonstrate that the resulting inelastic limit applies to a wider variety of experimental...... conditions than similar, previously derived formulas, and it directly allows the application of selection rules when interpreting diffraction signals. Furthermore, we present a simple extension to systems simultaneously illuminated by x rays and a laser beam....
Magnetic Dynamics of Fine Particles Studied by Inelastic Neutron Scattering
DEFF Research Database (Denmark)
Hansen, Mikkel Fougt; Bødker, Franz; Mørup, Steen
2000-01-01
We give an introduction to inelastic neutron scattering and the dynamic scattering function for magnetic nanoparticles. Differences between ferromagnetic and antiferromagnetic nanoparticles are discussed and we give a review of recent results on ferromagnetic Fe nanoparticles and canted antiferro......We give an introduction to inelastic neutron scattering and the dynamic scattering function for magnetic nanoparticles. Differences between ferromagnetic and antiferromagnetic nanoparticles are discussed and we give a review of recent results on ferromagnetic Fe nanoparticles and canted...
Deep inelastic scattering in spontaneously broken gauge models
International Nuclear Information System (INIS)
Goloskokov, S.V.; Mikhov, S.G.; Morozov, P.T.; Stamenov, D.B.
1975-01-01
Deep inelastic lepton hadron scattering in the simplest spontaneously broken symmetry (the Kibble model) is analyzed. A hypothesis that the invariant coupling constant of the quartic selfinteraction for large spacelike momenta tends to a finite asymptotic value without spoiling the asymptotic freedom for the invariant coupling constant of the Yang-Mills field is used. It is shown that Biorken scaling for the moments of the structure functions of the deep inelastic lepton hadron scattering is violated by powers of logarithms
Significance of matrix diagonalization in modelling inelastic electron scattering
Energy Technology Data Exchange (ETDEWEB)
Lee, Z. [University of Ulm, Ulm 89081 (Germany); Hambach, R. [University of Ulm, Ulm 89081 (Germany); University of Jena, Jena 07743 (Germany); Kaiser, U.; Rose, H. [University of Ulm, Ulm 89081 (Germany)
2017-04-15
Electron scattering is always applied as one of the routines to investigate nanostructures. Nowadays the development of hardware offers more and more prospect for this technique. For example imaging nanostructures with inelastic scattered electrons may allow to produce component-sensitive images with atomic resolution. Modelling inelastic electron scattering is therefore essential for interpreting these images. The main obstacle to study inelastic scattering problem is its complexity. During inelastic scattering, incident electrons entangle with objects, and the description of this process involves a multidimensional array. Since the simulation usually involves fourdimensional Fourier transforms, the computation is highly inefficient. In this work we have offered one solution to handle the multidimensional problem. By transforming a high dimensional array into twodimensional array, we are able to perform matrix diagonalization and approximate the original multidimensional array with its twodimensional eigenvectors. Our procedure reduces the complicated multidimensional problem to a twodimensional problem. In addition, it minimizes the number of twodimensional problems. This method is very useful for studying multiple inelastic scattering. - Highlights: • 4D problems are involved in modelling inelastic electron scattering. • By means of matrix diagonalization, the 4D problems can be simplified as 2D problems. • The number of 2D problems is minimized by using this approach.
Acoustophoretic separation of airborne millimeter-size particles by a Fresnel lens
Cicek, Ahmet; Korozlu, Nurettin; Adem Kaya, Olgun; Ulug, Bulent
2017-03-01
We numerically demonstrate acoustophoretic separation of spherical solid particles in air by means of an acoustic Fresnel lens. Beside gravitational and drag forces, freely-falling millimeter-size particles experience large acoustic radiation forces around the focus of the lens, where interplay of forces lead to differentiation of particle trajectories with respect to either size or material properties. Due to the strong acoustic field at the focus, radiation force can divert particles with source intensities significantly smaller than those required for acoustic levitation in a standing field. When the lens is designed to have a focal length of 100 mm at 25 kHz, finite-element method simulations reveal a sharp focus with a full-width at half-maximum of 0.5 wavelenghts and a field enhancement of 18 dB. Through numerical calculation of forces and simulation of particle trajectories, we demonstrate size-based separation of acrylic particles at a source sound pressure level of 153 dB such that particles with diameters larger than 0.5 mm are admitted into the central hole, whereas smaller particles are rejected. Besides, efficient separation of particles with similar acoustic properties such as polyethylene, polystyrene and acrylic particles of the same size is also demonstrated.
Biaxial-Type Concentrated Solar Tracking System with a Fresnel Lens for Solar-Thermal Applications
Directory of Open Access Journals (Sweden)
Tsung Chieh Cheng
2016-04-01
Full Text Available In this paper, an electromechanical, biaxial-type concentrated solar tracking system was designed for solar-thermal applications. In our tracking system, the sunlight was concentrated by the microstructure of Fresnel lens to the heating head of the Stirling engine and two solar cells were installed to provide the power for tracking system operation. In order to obtain the maximum sun power, the tracking system traces the sun with the altitude-azimuth biaxial tracing method and accurately maintains the sun’s radiation perpendicular to the plane of the heating head. The results indicated that the position of heating head is an important factor for power collection. If the sunlight can be concentrated to completely cover the heating head with small heat loss, we can obtain the maximum temperature of the heating head of the Stirling engine. Therefore, the temperature of heating head can be higher than 1000 °C in our experiment on a sunny day. Moreover, the results also revealed that the temperature decrease of the heating head is less than the power decrease of solar irradiation because of the latent heat of copper and the small heat loss from the heating head.
International Nuclear Information System (INIS)
Zhu, Yanqing; Shi, Jifu; Li, Yujian; Wang, Leilei; Huang, Qizhang; Xu, Gang
2016-01-01
Highlights: • A parabolic primary mirror field is designed to reduce the gap between adjacent mirrors. • The movable receiver can reduce the end losses. • The thermal efficiency of 66% is achieved at Guangzhou in winter. - Abstract: This paper proposes a stretched parabolic linear Fresnel reflector (SPLFR) collecting system. The primary optical mirror field of the SPLFR collecting system and the second-stage concentrator of compound parabolic collector are designed. The mirrors located at the parabolic line are close to each other, which effectively reduce the gap between the adjacent mirrors. The end losses of the receiver are very important, especially in a small-scale collecting system. A movable receiver is introduced for the reduction of the end losses. Moreover, a stretched structure of SPLFR is designed for wind resistance. Finally, the thermal performance of the SPLFR collecting system with fixed and movable receiver located in Guangzhou is tested. The maximum thermal efficiency obtained by this collecting system with movable receiver is 66% which avoid the end losses effectively, and the solar collector thermal loss coefficient is 1.32 W/m"2 °C. The results show that the SPLFR collecting system has excellent thermal performance and a promising application future. Meanwhile, this system will provide a valuable reference for concentrating solar power technology.
24-GHz LTCC Fractal Antenna Array SoP With Integrated Fresnel Lens
Ghaffar, Farhan A.
2012-09-30
A novel 24-GHz mixed low-temperature co-fired ceramic (LTCC) tape based system-on-package (SoP) is presented, which incorporates a fractal antenna array with an integrated grooved Fresnel lens. The four-element fractal array employs a relatively low dielectric constant substrate (CT707, εr = 6.4), whereas the lens has been realized on a high-dielectric-constant superstrate (CT765, εr = 68.7 ). The two (substrate and superstrate) are integrated through four corner posts to realize the required air gap (focal distance). The fractal array alone provides a measured gain of 8.9 dBi. Simulations predict that integration of this array with the lens increases the gain by 6 dB. Measurements reveal that the design is susceptible to LTCC fabrication tolerances. In addition to high gain, the SoP provides a bandwidth of 8%. The high performance and compact size (24 × 24 × 4.8 mm3 ) of the design makes it highly suitable for emerging wireless applications such as automotive radar front end.
Sparse synthetic aperture with Fresnel elements (S-SAFE) using digital incoherent holograms
Kashter, Yuval; Rivenson, Yair; Stern, Adrian; Rosen, Joseph
2015-01-01
Creating a large-scale synthetic aperture makes it possible to break the resolution boundaries dictated by the wave nature of light of common optical systems. However, their implementation is challenging, since the generation of a large size continuous mosaic synthetic aperture composed of many patterns is complicated in terms of both phase matching and time-multiplexing duration. In this study we present an advanced configuration for an incoherent holographic imaging system with super resolution qualities that creates a partial synthetic aperture. The new system, termed sparse synthetic aperture with Fresnel elements (S-SAFE), enables significantly decreasing the number of the recorded elements, and it is free from positional constrains on their location. Additionally, in order to obtain the best image quality we propose an optimal mosaicking structure derived on the basis of physical and numerical considerations, and introduce three reconstruction approaches which are compared and discussed. The super-resolution capabilities of the proposed scheme and its limitations are analyzed, numerically simulated and experimentally demonstrated. PMID:26367947
Stable and simple quantitative phase-contrast imaging by Fresnel biprism
Ebrahimi, Samira; Dashtdar, Masoomeh; Sánchez-Ortiga, Emilio; Martínez-Corral, Manuel; Javidi, Bahram
2018-03-01
Digital holographic (DH) microscopy has grown into a powerful nondestructive technique for the real-time study of living cells including dynamic membrane changes and cell fluctuations in nanometer and sub-nanometer scales. The conventional DH microscopy configurations require a separately generated coherent reference wave that results in a low phase stability and a necessity to precisely adjust the intensity ratio between two overlapping beams. In this work, we present a compact, simple, and very stable common-path DH microscope, employing a self-referencing configuration. The microscope is implemented by a diode laser as the source and a Fresnel biprism for splitting and recombining the beams simultaneously. In the overlapping area, linear interference fringes with high contrast are produced. The frequency of the interference pattern could be easily adjusted by displacement of the biprism along the optical axis without a decrease in fringe contrast. To evaluate the validity of the method, the spatial noise and temporal stability of the setup are compared with the common off-axis DH microscope based on a Mach-Zehnder interferometer. It is shown that the proposed technique has low mechanical noise as well as superb temporal stability with sub-nanometer precision without any external vibration isolation. The higher temporal stability improves the capabilities of the microscope for studying micro-object fluctuations, particularly in the case of biological specimens. Experimental results are presented using red blood cells and silica microspheres to demonstrate the system performance.
Extended Huygens-Fresnel principle and optical waves propagation in turbulence: discussion.
Charnotskii, Mikhail
2015-07-01
Extended Huygens-Fresnel principle (EHF) currently is the most common technique used in theoretical studies of the optical propagation in turbulence. A recent review paper [J. Opt. Soc. Am. A31, 2038 (2014)JOAOD60740-323210.1364/JOSAA.31.002038] cites several dozens of papers that are exclusively based on the EHF principle. We revisit the foundations of the EHF, and show that it is burdened by very restrictive assumptions that make it valid only under weak scintillation conditions. We compare the EHF to the less-restrictive Markov approximation and show that both theories deliver identical results for the second moment of the field, rendering the EHF essentially worthless. For the fourth moment of the field, the EHF principle is accurate under weak scintillation conditions, but is known to provide erroneous results for strong scintillation conditions. In addition, since the EHF does not obey the energy conservation principle, its results cannot be accurate for scintillations of partially coherent beam waves.
Measurement of an electron-beam size with a beam profile monitor using Fresnel zone plates
International Nuclear Information System (INIS)
Iida, K.; Nakamura, N.; Sakai, H.; Shinoe, K.; Takaki, H.; Fujisawa, M.; Hayano, H.; Nomura, M.; Kamiya, Y.; Koseki, T.; Amemiya, Y.; Aoki, N.; Nakayama, K.
2003-01-01
We present a non-destructive and real-time beam profile monitor using Fresnel zone plates (FZPs) and the measurement of an electron-beam size with this monitor in the KEK-Accelerator Test Facility (ATF) damping ring. The monitor system has the structure of a long-distance X-ray microscope, where two FZPs constitute an X-ray imaging optics. The synchrotron radiation from the electron beam at the bending magnet is monochromatized by a crystal monochromator and the transverse electron beam image is twenty times magnified by the two FZPs and detected on an X-ray CCD camera. The expected spatial resolution for the selected photon energy of 3.235 keV is sufficiently high to measure the horizontal and vertical beam sizes of the ATF damping ring. With the beam profile monitor, we succeeded in obtaining a clear electron-beam image and measuring the extremely small beam size less than 10 μm. The measured magnification of the X-ray imaging optics in the monitor system was in good agreement with the design value
Pinhole diffraction holography for fabrication of high-resolution Fresnel zone plates.
Sarkar, Sankha S; Solak, Harun H; David, Christian; van der Veen, J Friso
2014-01-27
Fresnel zone plates (FZPs) play an essential role in high spatial resolution x-ray imaging and analysis of materials in many fields. These diffractive lenses are commonly made by serial writing techniques such as electron beam or focused ion beam lithography. Here we show that pinhole diffraction holography has potential to generate FZP patterns that are free from aberrations and imperfections that may be present in alternative fabrication techniques. In this presented method, FZPs are fabricated by recording interference pattern of a spherical wave generated by diffraction through a pinhole, illuminated with coherent plane wave at extreme ultraviolet (EUV) wavelength. Fundamental and practical issues involved in formation and recording of the interference pattern are considered. It is found that resolution of the produced FZP is directly related to the diameter of the pinhole used and the pinhole size cannot be made arbitrarily small as the transmission of EUV or x-ray light through small pinholes diminishes due to poor refractive index contrast found between materials in these spectral ranges. We also find that the practical restrictions on exposure time due to the light intensity available from current sources directly imposes a limit on the number of zones that can be printed with this method. Therefore a trade-off between the resolution and the FZP diameter exists. Overall, we find that this method can be used to fabricate aberration free FZPs down to a resolution of about 10 nm.
Solar concentrator modules with silicone-on-glass Fresnel lens panels and multijunction cells.
Rumyantsev, Valery D
2010-04-26
High-efficiency multijunction (MJ) solar cells, being very expensive to manufacture, should only be used in combination with solar concentrators in terrestrial applications. An essential cost reduction of electric power produced by photovoltaic (PV) installations with MJ cells, may be expected by the creation of highly-effective, but inexpensive, elements for optical concentration and sun tracking. This article is an overview of the corresponding approach under development at the Ioffe Physical Technical Institute. The approach to R&D of the solar PV modules is based on the concepts of sunlight concentration by small-aperture area Fresnel lenses and "all-glass" module design. The small-aperture area lenses are arranged as a panel with silicone-on-glass structure where the glass plate serves as the front surface of a module. In turn, high-efficiency InGaP/(In)GaAs/Ge cells are arranged on a rear module panel mounted on a glass plate which functions as a heat sink and integrated protective cover for the cells. The developed PV modules and sun trackers are characterized by simple design, and are regarded as the prototypes for further commercialization.
Solar concentrator modules with silicone-onglass Fresnel lens panels and multijunction cells.
Rumyantsev, Valery D
2010-04-26
High-efficiency multijunction (MJ) solar cells, being very expensive to manufacture, should only be used in combination with solar concentrators in terrestrial applications. An essential cost reduction of electric power produced by photovoltaic (PV) installations with MJ cells, may be expected by the creation of highly-effective, but inexpensive, elements for optical concentration and sun tracking. This article is an overview of the corresponding approach under development at the Ioffe Physical Technical Institute. The approach to R&D of the solar PV modules is based on the concepts of sunlight concentration by small-aperture area Fresnel lenses and "all-glass" module design. The small-aperture area lenses are arranged as a panel with silicone-on-glass structure where the glass plate serves as the front surface of a module. In turn, high-efficiency InGaP/(In)GaAs/Ge cells are arranged on a rear module panel mounted on a glass plate which functions as a heat sink and integrated protective cover for the cells. The developed PV modules and sun trackers are characterized by simple design, and are regarded as the prototypes for further commercialization.
Deep Inelastic Scattering in Conformal QCD
Cornalba, Lorenzo; Penedones, Joao
2010-01-01
We consider the Regge limit of a CFT correlation function of two vector and two scalar operators, as appropriate to study small-x deep inelastic scattering in N=4 SYM or in QCD assuming approximate conformal symmetry. After clarifying the nature of the Regge limit for a CFT correlator, we use its conformal partial wave expansion to obtain an impact parameter representation encoding the exchange of a spin j Reggeon for any value of the coupling constant. The CFT impact parameter space is the three-dimensional hyperbolic space H3, which is the impact parameter space for high energy scattering in the dual AdS space. We determine the small-x structure functions associated to the exchange of a Reggeon. We discuss unitarization from the point of view of scattering in AdS and comment on the validity of the eikonal approximation. We then focus on the weak coupling limit of the theory where the amplitude is dominated by the exchange of the BFKL pomeron. Conformal invariance fixes the form of the vector impact factor a...
Inclusive deep-inelastic muon scattering
This experiment aims at measuring deep-inelastic inclusive muon scattering to the highest energy and Q$^{2}$ made available by the high intensity muon beam M$^{2}$ and at investigating events in which several muons are simultaneously produced. The momentum of the incident beam is measured with momentum hodoscopes, its time and space coordinates at several positions along the target with additional hodoscopes. The beam halo is detected by an array of anticounters. The target has a length of 40 m of either graphite or liquid hydrogen or liquid deuterium and is surrounded by a magnetized torus which acts as a spectrometer for scattered muons. \\\\ \\\\This magnet has a diameter of 2.75 m and is divided into 10 separate supermodules, 8 of which are presently in use. Each supermodule consists of 8 modules (each module contains 0.44 m of steel), 8 planes of (3m x 3m) MWPC, and 2 planes of circular trigger counters subdivided in rings. The first 6 supermodules are equipped each with a 5 m long target. Muons scattered i...
Quantum effects in deep inelastic neutron scattering
International Nuclear Information System (INIS)
Mayers, J.
1989-07-01
In the Impulse Approximation (IA), which is used to interpret deep inelastic neutron scattering (DINS) measurements, it is assumed both that the target system can be treated as a gas of free atoms and that the struck atom recoils freely after the collision with the neutron. Departures from the IA are generally attributed to final state effects (FSE), which are due to the inaccuracy of the latter assumption. However it is shown that even when FSE are neglected, significant departures from the IA occur at low temperatures due to inaccuracies in the former assumption. These are referred to as initial state effects (ISE) and are due to the quantum nature of the initial state. Comparison with experimental data and exactly soluble models shows that ISE largely account for observed asymmetries and peak shifts in the neutron scattering function S(q,ω), compared with the IA prediction. It is shown that when FSE are neglected, ISE can also be neglected when either the momentum transfer or the temperature is high. Finally it is shown that FSE should be negligible at high momentum transfers in systems other than quantum fluids and that therefore in this regime the IA is reached in such systems. (author)
Inelastic neutron scattering of amorphous ice
International Nuclear Information System (INIS)
Fukazawa, Hiroshi; Ikeda, Susumu; Suzuki, Yoshiharu
2001-01-01
We measured the inelastic neutron scattering from high-density amorphous (HDA) and low-density amorphous (LDA) ice produced by pressurizing and releasing the pressure. We found a clear difference between the intermolecular vibrations in HDA and those in LDA ice: LDA ice has peaks at 22 and 33 meV, which are also seen in the spectrum of lattice vibrations in ice crystal, but the spectrum of HDA ice does not have these peaks. The excitation energy of librational vibrations in HDA ice is 10 meV lower than that in LDA ice. These results imply that HDA ice includes 2- and 5-coordinated hydrogen bonds that are created by breakage of hydrogen bonds and migration of water molecules into the interstitial site, while LDA ice contains mainly 4-coordinated hydrogen bonds and large cavities. Furthermore, we report the dynamical structure factor in the amorphous ice and show that LDA ice is more closely related to the ice crystal structure than to HDA ice. (author)
Hard diffraction and deep inelastic scattering
International Nuclear Information System (INIS)
Bjorken, J.D.
1994-04-01
Since the advent of hard-collision physics, the study of diffractive processes - shadow physics - has been less prominent than before. However, there is now a renewed interest in the subject, especially in that aspect which synthesizes the short-distance, hard-collision phenomena with the classical physics of large rapidity-gaps. This is especially stimulated by the recent data on deep-inelastic scattering from HERA, as well as the theoretical work which relates to it. The word diffraction is sometimes used by high-energy physicists in a loose way. The author defines this term to mean: A diffractive process occurs if and only if there is a large rapidity gap in the produced-particle phase space which is not exponentially suppressed. Here a rapidity gap means essentially no hadrons produced into the rapidity gap (which operates in the open-quotes legoclose quotes phase-space of pseudo-rapidity and azimuthal angle). And non-exponential suppression implies that the cross-section for creating a gap with width Δη does not have a power-law decrease with increasing subenergy s=e Δη , but behaves at most like some power of pseudorapidity Δη∼log(s). The term hard diffraction shall simply refer to those diffractive process which have jets in the final-state phase-space
Detailed inelastic analysis of an LMFBR pipeline
International Nuclear Information System (INIS)
Hibbitt, H.D.; Leung, E.K.; Ohalla, A.K.
1982-01-01
The paper describes detailed inelastic analyses of a large diameter, thin walled pipeline configuration typical of liquid metal cooled reactor primary piping, subject to thermal shock, with intermediate periods of creep hold time. Three such analyses are compared. Two of these analyses are performed with recently developed elements based on a combination of Fourier and polynomial interpolation to describe the deformation of the pipe. One of these two analyses includes continuous deformation of the pipe wall between each elbow and the adjacent straight pipe segments, while the other neglects such ''end effects'' on the elbow deformation. The third analysis is based on a modified axi-symmetric shell element for modeling the elbows (neglecting and effects). The results thus provide an assessment of the relative cost and importance of including consideration of end effects in modeling a realistic piping system, as well as providing a similar comparison between the two basic deforming section pipe models (Fourier/polynomial versus modified axi-symmetric shells)
Configuration of an inelastic flexible anchored cable
Directory of Open Access Journals (Sweden)
T. P. Dreyer
1992-07-01
Full Text Available Consider an inelastic, perfectly flexible cable with given external forces acting on the total length of the cable. The one end-point is fixed in the origin and the other end-point is anchored at a given point (a;b;c in space. The resulting configuration of the cable in space can be modelled by a system of non-linear differential equations. In this article it is shown that this continuous model of the cable can always be solved in terms of an integral. In the special case of a constant (i.e. independent of the position on the cable external force per unit length the solution is given explicitly in terms of three constants that describe the tension at the origin. These three constants are determined by the boundary values a, b and c at the other end-point, and must be calculated in general by a numerical procedure from the three resulting simultaneous non-linear equations. A few applications of this method are shown.
Folding models for elastic and inelastic scattering
International Nuclear Information System (INIS)
Satchler, G.R.
1982-01-01
The most widely used models are the optical model potential (OMP) for elastic scattering, and its generalization to non-spherical shapes, the deformed optical model potential (DOMP) for inelastic scattering. These models are simple and phenomenological; their parameters are adjusted so as to reproduce empirical data. Nonetheless, there are certain, not always well-defined, constraints to be imposed. The potential shapes and their parameter values must be reasonable and should vary in a smooth and systematic way with the masses of the colliding nuclei and their energy. One way of satisfying these constraints, without going back to a much more fundamental theory, is through the use of folding models. The basic justification for using potentials of the Woods-Saxon shape for nucleon-nucleus scattering, for example, is our knowledge that a nuclear density distribution is more-or-less constant in the nuclear interior with a diffuse surface. When this is folded with a short-range nucleon-nucleon interaction, the result is a similar shape with a more diffuse surface. Folding procedures allow us to incorporate many aspects of nuclear structure (although the nuclear size is one of the most important), as well as theoretical ideas about the effective interaction of two nucleons within nuclear matter. It also provides us with a means of linking information obtained from nuclear (hadronic) interactions with that from other sources, as well as correlating that from the use of different hadronic probes. Folding model potentials, single-folded potentials, and the double-folding model including applications to heavy-ion scattering are discussed
Deep inelastic collisions between very heavy nuclei
International Nuclear Information System (INIS)
Sann, H.; Olmi, A.; Civelekoglu, Y.
1977-01-01
A systematic survey of deep inelastic reactions was performed for colliding nuclei of masses between 80 and 240 amu. The application of large surface detectors and, particularly, of a position sensitive ionization chamber, has proved to be very effective and appropriate for this type of investigation. The Wilczynski diagrams describing the relative motion between the colliding objects shows a gradual trend as a function of growing masses of target and projectile where the trajectories lead the particles not toward negative scattering angles but increasingly into the direction around and above the grazing angle. This behavior is attributed to a delicate balance between Coulomb and nuclear forces. The energy dumping as a function of the mass transfer strength matches a general law between total kinetic energy loss and the variance of the proton number distribution. For the partly damped component this relation seems to hold independently from the choice of ingoing channel and bombarding energy. The dissipation of the kinetic energy does not depend only on the relative velocity of the impinging nuclei, and the simple friction model is not appropriate to describe these processes. The γ-multiplicity measurement displays a rapid increase as a function of scattering angle and total kinetic energy loss, which give new insights to the process and indicate the necessity of microscopic quantum mechanical calculations of the interaction. In the U-U collision large mass transfers are present which possibly populate with relatively large cross sections the transuranic elements. In the Pb-Pb reaction the mass transfer is more restricted. The decay probability by fission of the primary masses increases strongly for growing masses and excitation energies
Photon diffractive dissociation in deep inelastic scattering
International Nuclear Information System (INIS)
Wuesthoff, M.
1995-09-01
The cross section of the Photon Diffractive Dissociation in Deep Inelastic Scattering is calculated in the frame work of perturbative QCD. In the triple Regge region the BFKL-approximation is used to evaluate the leading contributions of the corresponding Feynman diagrams with a subsequent resummation in terms of integral equations. These equations are partly solved leading to an effective two to four gluons transition vertex. This exhibits remarkable properties like the total symmetry under the interchange of gluons, the conformal invariance and a simple colour structure. The presence of four interacting gluons in the t-channel does not support the simple triple Pomeron picture with solely a local vertex. A dimensional conservation law is found for zero momentum transfer with the consequence that a direct coupling of the three BFKL-singularities is absent. Another consequence is the dominance of small transverse momenta at the triple Pomeron vertex. Beyond the triple Regge limit a slightly different approach is used in which the diagrams are calculated with leading log(Q 2 ) accuracy. Higher twist contributions are neglected except for the longitudinal part of the cross section which dominates at small invariant masses M in accordance with QCD-predictions and measurements for the exclusive production of vector mesons. For the comparison with the recently measured Photon Diffractive Dissociation-data from H1 and ZEUS a model for the Pomeron is introduced based on the F 2 -data. In the spirit of the k t -factorization theorem this model is inserted in place of the BFKL-Pomeron. Considering the fact that this approach does not contain free parameters the agreement between the theoretical prediction and the data is found to be good. (orig.)
Hard Distraction and Deep Inelastic Scattering
International Nuclear Information System (INIS)
BJORKEN, J.D.
1994-01-01
Since the advent of hard-collision physics, the study of diffractive processes- 'shadow physics' - has been less prominent than before. However, there is now a renewed interest in the subject, especially in that aspect which synthesizes the short-distance, hard-collision phenomena with the classical physics of large rapidity-gaps. This is especially stimulated by the recent data on deep-inelastic scattering from HERA, as well as the theoretical work which relates to it. The word 'diffraction' is sometimes used by high-energy physicists in a loose way. So I here begin by defining what I mean by the term: A diffractive process occurs if and only if there is a large rapidity gap in the produced-particle phase space which is not exponentially suppressed. Here a rapidity gap means essentially no hadrons produced into the rapidity gap (which operates in the 'lego' phase-space of pseudo-rapidity and azimuthal angle). And non-exponential suppression implies that the cross-section for creating a gap with width Δη does not have a power-law decrease with increasing sub energy Δη, but behaves at most like some power of pseudorapidity Δη∼ logs. The term 'hard diffraction' shall simply refer to those diffractive processes which have jets in the final-state phase-space. We may also distinguish, if desired, two subclasses, as suggested by Ingelman i) Diffractive hard processes have jets on only one side of the rapidity gap. ii) Hard diffractive processes have jets on both sides of the rapidity gap
Pion inelastic scattering and the pion-nucleus effective interaction
International Nuclear Information System (INIS)
Carr, J.A.
1983-01-01
This work examines pion inelastic scattering with the primary purpose of gaining a better understanding of the properties of the pion-nucleus interaction. The main conclusion of the work is that an effective interaction which incorporates the most obvious theoretical corrections to the impulse approximation does a good job of explaining pion elastic and inelastic scattering from zero to 200 MeV without significant adjustments to the strength parameters of the force. Watson's multiple scattering theory is used to develop a theoretical interaction starting from the free pion-nucleon interaction. Elastic scattering was used to calibrate the isoscalar central interaction. It was found that the impulse approximation did poorly at low energy, while the multiple scattering corrections gave good agreement with all of the data after a few minor adjustments in the force. The distorted wave approximation for the inelastic transition matrix elements are evaluated for both natural and unnatural parity excitations. The isoscalar natural parity transitions are used to test the reaction theory, and it is found that the effective interaction calibrated by elastic scattering produces good agreement with the inelastic data. Calculations are also shown for other inelastic and charge exchange reactions. It appears that the isovector central interaction is reasonable, but the importance of medium corrections cannot be determined. The unnatural parity transitions are also reasonably described by the theoretical estimate of the spin-orbit interaction, but not enough systematic data exists to reach a firm conclusion
Inelastic analysis acceptance criteria for radioactive material transportation containers
International Nuclear Information System (INIS)
Ammerman, D.J.; Ludwigsen, J.S.
1993-01-01
The design criteria currently used in the design of radioactive material (RAM) transportation containers are taken from the ASME Boiler and Pressure Vessel Code (ASME, 1992). These load-based criteria are ideally suited for pressure vessels where the loading is quasistatic and all stresses are in equilibrium with externally applied loads. For impact events, the use of load-based criteria is less supportable. Impact events tend to be energy controlled, and thus, energy-based acceptance criteria would appear to be more appropriate. Determination of an ideal design criteria depends on what behavior is desired. Currently there is not a design criteria for inelastic analysis for RAM nation packages that is accepted by the regulatory agencies. This lack of acceptance criteria is one of the major factors in limiting the use of inelastic analysis. In this paper inelastic analysis acceptance criteria based on stress and strain-energy density will be compared for two stainless steel test units subjected to impacts onto an unyielding target. Two different material models are considered for the inelastic analysis, a bilinear fit of the stress-strain curve and a power law hardening model that very closely follows the stress-strain curve. It is the purpose of this paper to stimulate discussion and research into the area of strain-energy density based inelastic analysis acceptance criteria
Inelastic scattering of quasifree electrons on O7+ projectiles
International Nuclear Information System (INIS)
Toth, G.; Grabbe, S.; Richard, P.; Bhalla, C.P.
1996-01-01
Absolute doubly differential cross sections (DDCS close-quote s) for the resonant inelastic scattering of quasifree target electrons on H-like projectiles have been measured. Electron spectra for 20.25-MeV O 7+ projectiles on an H 2 target were measured. The spectra contain a resonant contribution from the 3l3l ' doubly excited states of O 6+ , which decay predominantly to the 2l states of the O 7+ via autoionization, and a nonresonant contribution from the direct excitation of the projectiles to the O 7+ (2l) state by the quasifree target electrons. Close-coupling R-matrix calculations for the inelastic scattering of free electrons on O 7+ ions were performed. The relation between the electron-ion inelastic scattering calculation and the electron DDCS close-quote s for the ion-atom collision was established by using the inelastic scattering model (ISM). We found excellent agreement between the theoretical and measured resonant peak positions and relative peak heights. The calculated absolute double differential cross sections for the resonance processes are also in good agreement with the measured data. The implication is that collisions of highly charged ions on hydrogen can be used to obtain high-resolution, angle- resolved differential inelastic electron-scattering cross section. copyright 1996 The American Physical Society
Energy Technology Data Exchange (ETDEWEB)
Chen Jie; Li Wenjie; Tian Jinping; Liu Longhua; Xiong Ying; Liu Gang; Wu Ziyu; Tian Yangchao [National Synchrotron Radiation Laboratory (China); Liu Yijin [School of Physics (China); Yue Zhengbo; Yu Hanqing [Laboratory of Environmental Engineering, School of Chemistry, University of Science and Technology of China, Hefei Anhui 230029 (China); Wang Chunru, E-mail: ychtian@ustc.edu.c [Institute of Chemistry, Chinese Academy of Sciences, Beijing 10060 (China)
2009-09-01
A transmission X-ray microscope using Fresnel zone-plates (FZPs) has been installed at U7A beamline of National Synchrotron Radiation Laboratory (NSRL). The objective FZP with 45 nm outermost zone width delivers a sub-50 nm resolution. A gold phase ring with 2.5 {mu}m thickness and 4 {mu}m width was placed at the focal plane of the objective FZP at 8 keV to produce a negative Zernike phase contrast. A series of samples were used to test the performance of the Zernike phase contrast X-ray microscopy.
International Nuclear Information System (INIS)
Chen Jie; Li Wenjie; Tian Jinping; Liu Longhua; Xiong Ying; Liu Gang; Wu Ziyu; Tian Yangchao; Liu Yijin; Yue Zhengbo; Yu Hanqing; Wang Chunru
2009-01-01
A transmission X-ray microscope using Fresnel zone-plates (FZPs) has been installed at U7A beamline of National Synchrotron Radiation Laboratory (NSRL). The objective FZP with 45 nm outermost zone width delivers a sub-50 nm resolution. A gold phase ring with 2.5 μm thickness and 4 μm width was placed at the focal plane of the objective FZP at 8 keV to produce a negative Zernike phase contrast. A series of samples were used to test the performance of the Zernike phase contrast X-ray microscopy.
Bakunov, M I; Maslov, A V; Bodrov, S B
2007-11-16
We show that the usual Fresnel formulas for a free-propagating pulse are not applicable for a forced terahertz electromagnetic pulse supported by an optical pulse at the end of a nonlinear crystal. The correct linear reflection and transmission coefficients that we derive show that such pulses can experience a gain or loss at the boundary. This energy change depends on linear dielectric constants only. We also predict a regime where a complete disappearance of the forced pulse under oblique incidence occurs, an effect that has no counterpart for free-propagating pulses.
Wang, Guangzhen; Wang, Lili; Li, Fuli; Kong, Depeng
2012-09-01
One kind of optical element combining Fresnel lens with microlens array is designed simply for LED lighting based on geometrical optics and nonimaging optics. This design method imposes no restriction on the source intensity pattern. The designed element has compact construction and can produce multiple shapes of illumination distribution. Taking square lighting as an example, tolerance analysis is carried out to determine tolerance limits for applying the element in the assembly process. This element can produce on-axis lighting and off-axis lighting.
Inelastic Production of J/psi Mesons in Photoproduction and Deep Inelastic Scattering at HERA
Aaron, F.D.; Andreev, V.; Antunovic, B.; Backovic, S.; Baghdasaryan, A.; Barrelet, E.; Bartel, W.; Begzsuren, K.; Belousov, A.; Bizot, J.C.; Boudry, V.; Bozovic-Jelisavcic, I.; Bracinik, J.; Brandt, G.; Brinkmann, M.; Brisson, V.; Bruncko, D.; Bunyatyan, A.; Buschhorn, G.; Bystritskaya, L.; Campbell, A.J.; Cantun Avila, K.B.; Cerny, K.; Cerny, V.; Chekelian, V.; Cholewa, A.; Contreras, J.G.; Coughlan, J.A.; Cozzika, G.; Cvach, J.; Dainton, J.B.; Daum, K.; Deak, M.; Delcourt, B.; Delvax, J.; De Wolf, E.A.; Diaconu, C.; Dodonov, V.; Dossanov, A.; Dubak, A.; Eckerlin, G.; Efremenko, V.; Egli, S.; Eliseev, A.; Elsen, E.; Falkiewicz, A.; Favart, L.; Fedotov, A.; Felst, R.; Feltesse, J.; Ferencei, J.; Fischer, D.J.; Fleischer, M.; Fomenko, A.; Gabathuler, E.; Gayler, J.; Ghazaryan, S.; Glazov, A.; Goerlich, L.; Gogitidze, N.; Gouzevitch, M.; Grab, C.; Grebenyuk, A.; Greenshaw, T.; Grell, B.R.; Grindhammer, G.; Habib, S.; Haidt, D.; Helebrant, C.; Henderson, R.C.W.; Hennekemper, E.; Henschel, H.; Herbst, M.; Herrera, G.; Hildebrandt, M.; Hiller, K.H.; Hoffmann, D.; Horisberger, R.; Hreus, T.; Jacquet, M.; Janssen, X.; Jonsson, L.; Jung, A.W.; Jung, H.; Kapichine, M.; Katzy, J.; Kenyon, I.R.; Kiesling, C.; Klein, M.; Kleinwort, C.; Kluge, T.; Knutsson, A.; Kogler, R.; Kostka, P.; Kraemer, M.; Krastev, K.; Kretzschmar, J.; Kropivnitskaya, A.; Kruger, K.; Kutak, K.; Landon, M.P.J.; Lange, W.; Lastovicka-Medin, G.; Laycock, P.; Lebedev, A.; Lendermann, V.; Levonian, S.; Li, G.; Lipka, K.; Liptaj, A.; List, B.; List, J.; Loktionova, N.; Lopez-Fernandez, R.; Lubimov, V.; Makankine, A.; Malinovski, E.; Marage, P.; Marti, Ll.; Martyn, H.U.; Maxfield, S.J.; Mehta, A.; Meyer, A.B.; Meyer, H.; Meyer, J.; Mikocki, S.; Milcewicz-Mika, I.; Moreau, F.; Morozov, A.; Morris, J.V.; Mozer, M.U.; Mudrinic, M.; Muller, K.; Murin, P.; Naumann, Th.; Newman, P.R.; Niebuhr, C.; Nikiforov, A.; Nikitin, D.; Nowak, G.; Nowak, K.; Olsson, J.E.; Osman, S.; Ozerov, D.; Pahl, P.; Palichik, V.; Panagoulias, I.; Pandurovic, M.; Papadopoulou, Th.; Pascaud, C.; Patel, G.D.; Perez, E.; Petrukhin, A.; Picuric, I.; Piec, S.; Pitzl, D.; Placakyte, R.; Pokorny, B.; Polifka, R.; Povh, B.; Radescu, V.; Raicevic, N.; Raspiareza, A.; Ravdandorj, T.; Reimer, P.; Rizvi, E.; Robmann, P.; Roosen, R.; Rostovtsev, A.; Rotaru, M.; Ruiz Tabasco, J.E.; Rusakov, S.; Salek, D.; Sankey, D.P.C.; Sauter, M.; Sauvan, E.; Schmitt, S.; Schoeffel, L.; Schoning, A.; Schultz-Coulon, H.C.; Sefkow, F.; Shaw-West, R.N.; Shtarkov, L.N.; Shushkevich, S.; Sloan, T.; Smiljanic, I.; Soloviev, Y.; Sopicki, P.; South, D.; Spaskov, V.; Specka, A.; Staykova, Z.; Steder, M.; Stella, B.; Stoicea, G.; Straumann, U.; Sunar, D.; Sykora, T.; Thompson, G.; Thompson, P.D.; Toll, T.; Tomasz, F.; Tran, T.H.; Traynor, D.; Truol, P.; Tsakov, I.; Tseepeldorj, B.; Turnau, J.; Urban, K.; Valkarova, A.; Vallee, C.; Van Mechelen, P.; Vargas Trevino, A.; Vazdik, Y.; Volchinski, V.; von den Driesch, M.; Wegener, D.; Wissing, Ch.; Wunsch, E.; Zacek, J.; Zalesak, J.; Zhang, Z.; Zhokin, A.; Zimmermann, T.; Zohrabyan, H.; Zomer, F.
2010-01-01
A measurement is presented of inelastic photo- and electroproduction of J/psi mesons in ep scattering at HERA. The data were recorded with the H1 detector in the period from 2004 to 2007. Single and double differential cross sections are determined and the helicity distributions of the J/psi mesons are analysed. The results are compared to theoretical predictions in the colour singlet model and in the framework of non-relativistic QCD. Calculations in the colour singlet model using a k_T factorisation ansatz are able to give a good description of the data, while colour singlet model calculations to next-to-leading order in collinear factorisation underestimate the data.
Inelastic production of J/{psi} mesons in photoproduction and deep inelastic scattering at HERA
Energy Technology Data Exchange (ETDEWEB)
Aaron, F.D.; Alexa, C.; Rotaru, M.; Stoicea, G. [National Inst. for Physics and Nuclear Engineering, Bucharest (Romania); Andreev, V.; Belousov, A.; Eliseev, A.; Fomenko, A.; Gogitidze, N.; Lebedev, A.; Loktionova, N.; Malinovski, E.; Rusakov, S.; Shtarkov, L.N.; Soloviev, Y.; Vazdik, Y. [Lebedev Physical Inst., Moscow (Russian Federation); Antunovic, B.; Bartel, W.; Brandt, G.; Campbell, A.J.; Cholewa, A.; Deak, M.; Eckerlin, G.; Elsen, E.; Felst, R.; Fischer, D.J.; Fleischer, M.; Gayler, J.; Ghazaryan, S.; Glazov, A.; Gouzevitch, M.; Grebenyuk, A.; Grell, B.R.; Haidt, D.; Helebrant, C.; Katzy, J.; Kleinwort, C.; Knutsson, A.; Kraemer, M.; Krastev, K.; Kutak, K.; Levonian, S.; Lipka, K.; List, J.; Marti, L.; Meyer, A.B.; Meyer, J.; Niebuhr, C.; Nikiforov, A.; Olsson, J.E.; Pahl, P.; Panagoulias, I.; Papadopoulou, T.; Pitzl, D.; Placakyte, R.; Schmitt, S.; Sefkow, F.; Staykova, Z.; Steder, M.; Sunar, D.; Vargas Trevino, A.; Driesch, M. von den; Wissing, C.; Wuensch, E. [DESY, Hamburg (Germany); Backovic, S.; Dubak, A.; Lastovicka-Medin, G.; Picuric, I.; Raicevic, N. [University of Montenegro, Faculty of Science, Podgorica (ME); Baghdasaryan, A.; Volchinski, V.; Zohrabyan, H. [Yerevan Physics Inst. (Armenia); Barrelet, E. [Univ. Pierre et Marie Curie Paris 6, Univ. Denis Diderot Paris 7, CNRS/IN2P3, LPNHE, Paris (France); Begzsuren, K.; Ravdandorj, T.; Tseepeldorj, B. [Inst. of Physics and Technology of the Mongolian Academy of Sciences, Ulaanbaatar (Mongolia); Bizot, J.C.; Brisson, V.; Delcourt, B.; Jacquet, M.; Li, G.; Pascaud, C.; Tran, T.H.; Zhang, Z.; Zomer, F. [Univ. Paris-Sud, CNRS/IN2P3, LAL, Orsay (France); Boudry, V.; Moreau, F.; Specka, A. [Ecole Polytechnique, CNRS/IN2P3, LLR, Palaiseau (France); Bozovic-Jelisavcic, I.; Mudrinic, M.; Pandurovic, M.; Smiljanic, I. [Vinca Inst. of Nuclear Sciences, Belgrade (RS); Bracinik, J.; Kenyon, I.R.; Newman, P.R.; Shaw-West, R.N.; Thompson, P.D. [University of Birmingham (United Kingdom)] [and others
2010-08-15
A measurement is presented of inelastic photo- and electroproduction of J/{psi} mesons in ep scattering at HERA. The data were recorded with the H1 detector in the period from 2004 to 2007. Single and double differential cross sections are determined and the helicity distributions of the J/{psi} mesons are analysed. The results are compared to theoretical predictions in the colour singlet model and in the framework of non-relativistic QCD. Calculations in the colour singlet model using a k{sub T} factorisation ansatz are able to give a good description of the data, while colour singlet model calculations to next-to-leading order in collinear factorisation underestimate the data. (orig.)
Inelastic production of J/ψ mesons in photoproduction and deep inelastic scattering at HERA
International Nuclear Information System (INIS)
Aaron, F.D.; Alexa, C.; Rotaru, M.; Stoicea, G.; Andreev, V.; Belousov, A.; Eliseev, A.; Fomenko, A.; Gogitidze, N.; Lebedev, A.; Loktionova, N.; Malinovski, E.; Rusakov, S.; Shtarkov, L.N.; Soloviev, Y.; Vazdik, Y.; Antunovic, B.; Bartel, W.; Brandt, G.; Campbell, A.J.; Cholewa, A.; Deak, M.; Eckerlin, G.; Elsen, E.; Felst, R.; Fischer, D.J.; Fleischer, M.; Gayler, J.; Ghazaryan, S.; Glazov, A.; Gouzevitch, M.; Grebenyuk, A.; Grell, B.R.; Haidt, D.; Helebrant, C.; Katzy, J.; Kleinwort, C.; Knutsson, A.; Kraemer, M.; Krastev, K.; Kutak, K.; Levonian, S.; Lipka, K.; List, J.; Marti, L.; Meyer, A.B.; Meyer, J.; Niebuhr, C.; Nikiforov, A.; Olsson, J.E.; Pahl, P.; Panagoulias, I.; Papadopoulou, T.; Pitzl, D.; Placakyte, R.; Schmitt, S.; Sefkow, F.; Staykova, Z.; Steder, M.; Sunar, D.; Vargas Trevino, A.; Driesch, M. von den; Wissing, C.; Wuensch, E.; Backovic, S.; Dubak, A.; Lastovicka-Medin, G.; Picuric, I.; Raicevic, N.; Baghdasaryan, A.; Volchinski, V.; Zohrabyan, H.; Barrelet, E.; Begzsuren, K.; Ravdandorj, T.; Tseepeldorj, B.; Bizot, J.C.; Brisson, V.; Delcourt, B.; Jacquet, M.; Li, G.; Pascaud, C.; Tran, T.H.; Zhang, Z.; Zomer, F.; Boudry, V.; Moreau, F.; Specka, A.; Bozovic-Jelisavcic, I.; Mudrinic, M.; Pandurovic, M.; Smiljanic, I.; Bracinik, J.; Kenyon, I.R.; Newman, P.R.; Shaw-West, R.N.; Thompson, P.D.; Brinkmann, M.; Habib, S.; List, B.; Toll, T.; Bruncko, D.; Cerny, V.; Ferencei, J.; Murin, P.; Tomasz, F.; Bunyatyan, A.; Buschhorn, G.; Chekelian, V.; Dossanov, A.; Grindhammer, G.; Kiesling, C.; Kogler, R.; Liptaj, A.; Raspiareza, A.; Shushkevich, S.; Bystritskaya, L.; Efremenko, V.; Fedotov, A.; Kropivnitskaya, A.; Lubimov, V.; Ozerov, D.; Petrukhin, A.; Rostovtsev, A.; Zhokin, A.; Cantun Avila, K.B.; Contreras, J.G.; Ruiz Tabasco, J.E.; Cerny, K.; Pokorny, B.; Polifka, R.; Salek, D.; Valkarova, A.; Zacek, J.; Coughlan, J.A.; Morris, J.V.; Sankey, D.P.C.; Cozzika, G.; Feltesse, J.; Perez, E.; Schoeffel, L.; Cvach, J.; Reimer, P.; Zalesak, J.; Dainton, J.B.; Gabathuler, E.; Greenshaw, T.; Klein, M.; Kluge, T.; Kretzschmar, J.; Laycock, P.; Maxfield, S.J.; Mehta, A.; Patel, G.D.; Daum, K.; Meyer, H.; Delvax, J.; Wolf, E.A.De; Favart, L.; Hreus, T.; Janssen, X.; Marage, P.; Mozer, M.U.; Roosen, R.; Sykora, T.; Mechelen, P. van; Diaconu, C.; Hoffmann, D.; Sauvan, E.; Vallee, C.; Dodonov, V.; Povh, B.; Egli, S.; Hildebrandt, M.; Horisberger, R.; Falkiewicz, A.; Goerlich, L.; Mikocki, S.; Milcewicz-Mika, I.; Nowak, G.; Sopicki, P.; Turnau, J.; Grab, C.; Zimmermann, T.; Henderson, R.C.W.; Sloan, T.; Hennekemper, E.; Herbst, M.; Jung, A.W.; Krueger, K.; Lendermann, V.; Schultz-Coulon, H.C.; Urban, K.; Henschel, H.; Hiller, K.H.; Kostka, P.; Lange, W.; Naumann, T.; Piec, S.; Herrera, G.; Lopez-Fernandez, R.; Joensson, L.; Osman, S.; Jung, H.; Kapichine, M.; Makankine, A.; Morozov, A.; Nikitin, D.; Palichik, V.; Spaskov, V.; Landon, M.P.J.; Rizvi, E.; Thompson, G.; Traynor, D.; Martyn, H.U.; Mueller, K.; Nowak, K.; Robmann, P.; Straumann, U.; Truoel, P.; Radescu, V.; Sauter, M.; Schoening, A.; South, D.; Wegener, D.; Stella, B.; Tsakov, I.
2010-01-01
A measurement is presented of inelastic photo- and electroproduction of J/ψ mesons in ep scattering at HERA. The data were recorded with the H1 detector in the period from 2004 to 2007. Single and double differential cross sections are determined and the helicity distributions of the J/ψ mesons are analysed. The results are compared to theoretical predictions in the colour singlet model and in the framework of non-relativistic QCD. Calculations in the colour singlet model using a k T factorisation ansatz are able to give a good description of the data, while colour singlet model calculations to next-to-leading order in collinear factorisation underestimate the data. (orig.)
The inelastic scattering of medium energy α particles
International Nuclear Information System (INIS)
Crut, M.
1960-01-01
The aim of this work is to find out what are the properties of the so-called 'anomalous states' in medium weight nuclei. These states preferentially excited in the inelastic scattering of medium energy charged particles have an excitation energy at about 4 MeV for nuclei with Z ≤ 29 and in the range 2-3 MeV for high Z nuclei. From a combination of angular distribution data in the elastic and inelastic scattering of 30 MeV α particles, and correlation data between inelastic α particles and deexcitation γ rays, we show that for even-even nuclei, we can attribute spin 3 and parity minus to these 'anomalous states'. This is quite in agreement with the interpretation of these levels suggested by Lane as due to collective octupole oscillations. We give a resume of the theories used in the analysis of the data and a description of the experimental set-up. (author) [fr
Halo-independent methods for inelastic dark matter scattering
International Nuclear Information System (INIS)
Bozorgnia, Nassim; Schwetz, Thomas; Herrero-Garcia, Juan; Zupan, Jure
2013-01-01
We present halo-independent methods to analyze the results of dark matter direct detection experiments assuming inelastic scattering. We focus on the annual modulation signal reported by DAMA/LIBRA and present three different halo-independent tests. First, we compare it to the upper limit on the unmodulated rate from XENON100 using (a) the trivial requirement that the amplitude of the annual modulation has to be smaller than the bound on the unmodulated rate, and (b) a bound on the annual modulation amplitude based on an expansion in the Earth's velocity. The third test uses the special predictions of the signal shape for inelastic scattering and allows for an internal consistency check of the data without referring to any astrophysics. We conclude that a strong conflict between DAMA/LIBRA and XENON100 in the framework of spin-independent inelastic scattering can be established independently of the local properties of the dark matter halo
Applications of one-dimensional models in simplified inelastic analyses
International Nuclear Information System (INIS)
Kamal, S.A.; Chern, J.M.; Pai, D.H.
1980-01-01
This paper presents an approximate inelastic analysis based on geometric simplification with emphasis on its applicability, modeling, and the method of defining the loading conditions. Two problems are investigated: a one-dimensional axisymmetric model of generalized plane strain thick-walled cylinder is applied to the primary sodium inlet nozzle of the Clinch River Breeder Reactor Intermediate Heat Exchanger (CRBRP-IHX), and a finite cylindrical shell is used to simulate the branch shell forging (Y) junction. The results are then compared with the available detailed inelastic analyses under cyclic loading conditions in terms of creep and fatigue damages and inelastic ratchetting strains per the ASME Code Case N-47 requirements. In both problems, the one-dimensional simulation is able to trace the detailed stress-strain response. The quantitative comparison is good for the nozzle, but less satisfactory for the Y junction. Refinements are suggested to further improve the simulation
Inelastic electron scattering influence on the strong coupling oxide superconductors
International Nuclear Information System (INIS)
Gabovich, A.M.; Voitenko, A.I.
1995-01-01
The superconducting order parameters Δ and energy gap Δ g are calculated taking into account the pair-breaking inelastic quasiparticle scattering by thermal Bose-excitations, e.g., phonons. The treatment is self-consistent because the scattering amplitude depends on Δ. The superconducting transition for any strength of the inelastic scattering is the phase transition of the first kind and the dependences Δ (T) and Δ g (T) tend to rectangular curve that agrees well with the experiment for high-Tc oxides. On the basis of the developed theory the nuclear spin-lattice relaxation rate R s in the superconducting state is calculated. The Hebel-Slichter peak in R s (T) is shown to disappear for strong enough inelastic scattering
QCD expectations for deep inelastic scattering at small x
International Nuclear Information System (INIS)
Kwiecinski, J.
1993-01-01
The basic QCD expectations concerning the deep inelastic scattering at low x where x is the Bjorken scaling variable are reviewed. This includes discussion of the Lipatov equation which sums the leading powers of Ln(1/x) and the shadowing effects. Phenomenological implications of the theoretical expectations for the deep inelastic lepton-hadron scattering in the small x region which will be accessible at the HERA ep collider are described. We give predictions for structure functions F 2 and F L based on the k T factorization theorem and discuss jet production in deep inelastic lepton scattering. The list of other topical problems relevant for the small x physics is given. (author). 46 refs, 7 figs
Magnon and phonon thermometry with inelastic light scattering
Olsson, Kevin S.; An, Kyongmo; Li, Xiaoqin
2018-04-01
Spin caloritronics investigates the interplay between the transport of spin and heat. In the spin Seebeck effect, a thermal gradient across a magnetic material generates a spin current. A temperature difference between the energy carriers of the spin and lattice subsystems, namely the magnons and phonons, is necessary for such thermal nonequilibrium generation of spin current. Inelastic light scattering is a powerful method that can resolve the individual temperatures of magnons and phonons. In this review, we discuss the thermometry capabilities of inelastic light scattering for measuring optical and acoustic phonons, as well as magnons. A scattering spectrum offers three temperature sensitive parameters: frequency shift, linewidth, and integrated intensity. We discuss the temperatures measured via each of these parameters for both phonon and magnons. Finally, we discuss inelastic light scattering experiments that have examined the magnon and phonon temperatures in thermal nonequilibrium which are particularly relevant to spin caloritronic phenomena.
Inelastic Structural Control Based on MBC and FAM
Directory of Open Access Journals (Sweden)
Li Gang
2011-01-01
Full Text Available A complex structure has the characters of many degrees of freedom and intricate shape, especially inelastic behavior under strong external loadings. It is hard to apply the structural control technology to it. In this paper, a new method that combines the Market-Based Control (MBC strategy and Force Analogy Method (FAM is presented to analyze the inelastic behavior of structure with magnetorheological dampers. The MBC is used to reduce the structural vibration response, and FAM is proposed to perform the inelastic analysis. A numerical example is used to compare the control effect of the new method and LQR algorithm, which show the accuracy and efficiency of the proposed computational method.
Inelastic structural design approach using their relaxation locus
International Nuclear Information System (INIS)
Kasahara, Naoto
2000-08-01
Elevated temperature structural design codes pay attention to strain concentration at structural discontinuities due to creep and plasticity, since it causes to enlarge creep-fatigue damage of materials. One of the difficulties to predict strain concentration is its dependency on loading, constitutive equations, and relaxation time. This study investigated fundamental mechanism of strain concentration and its main factors. The results revealed that strain concentration was caused from strain redistribution between elastic and inelastic region, which can be quantified by the characteristics of structural compliance. Characteristic of compliance is controlled by elastic region in structures and is insensitive to constitutive equations. It means that inelastic analysis is easily applied to get compliance characteristics. By utilizing this fact, simplified inelastic analysis method was proposed based on characteristics of compliance change for prediction of strain concentration. (author)
Inelastic electron scattering at low momentum transfer
International Nuclear Information System (INIS)
Richter, A.
1979-01-01
Recent advances of high energy resolution (ΔE approx. 30 keV FWHM) inelastic electron scattering at low momentum transfer (q -1 ) using selected experimental data from the Darmstadt electron linear accelerator are discussed. Strong emphasis is given to a comparison of the data with theoretical nuclear model predictions. Of the low multipolarity electric transitions investigated, as examples only E1 transitions to unnatural parity states in 11 B and E2 transitions of the very fragmented isoscalar quadrupole giant resonance in 208 Pb are considered. In 11 B the role of the Os hole in the configuration of the 1/2 + , 3/2 + and 5/2 + states is quantitatively determined via an interference mechanism in the transition probability. By comparison of the high resolution data with RPA calculations the E2 EWSR in 208 Pb is found to be much less exhausted than anticipated from previous medium energy resolution (e,e) and hadron scattering experiments. In the case of M1 transitions it is shown that the simplest idealized independent particle shell-model prediction breaks down badly. In 28 Si, ground-state correlations influence largely the detected M1 strength and such ground-state correlations are also responsible for the occurence of a strong M1 transition to a state at Ex = 10.319 MeV in 40 Ca. In 90 Zr only about 10% of the theoretically expected M1 strength is seen in (e,e) and in 140 Ce and 208 Pb none (detection limit 1-2 μ 2 K). In the case of 208 Pb high resolution spectra exist now up to an excitation energy of Ex = approx. 12MeV. The continuous decrease of the M1 strength with mass number is corroborated by the behaviour of strong but very fragmented M2 transitions which are detected in 28 Si, 90 Zr, 140 Ce and 208 Pb concentrated at an excitation energy E x approx. 44A -1 / 3 MeV. In 90 Zr, the distribution of spacings and widths of the many Jπ = 2 states are consistent with a Wigner and Porter-Thomas distribution, respectively. (orig.) 891 KBE/orig. 892 ARA
Wines: water inelastic neutron scattering experimental study
International Nuclear Information System (INIS)
Risch, P.; Ait Abderrahim, H.; D'hondt, P.; Malabu, E.
1997-01-01
An intercomparison of calculated fast neutron flux (E > 1 MeV) traverse through a very thick water zone obtained using both S N , (DORT) and Monte-Carlo (TRIPOLI and MCBEND) codes in combination with different cross-sections libraries (based on ENDF/B-III, IV, V and VI), showed small discrepancies either between S N , and Monte-Carlo results or even between S N , or Monte-Carlo results when we consider different cross-sections libraries except for S N , calculation when using P 0 , cross-sections. In order to validate our calculations we looked for experimental data. Unfortunately no experiment, dedicated for the fast neutron transport in large thickness of water, was found in the literature. Therefore SCK-CEN and EDF decided to launch the WINES experiment which is dedicated to study this phenomenon. WINES sands for Water Inelastic Neutron scattering Experimental Study. The aim of this experiment is to provide-experimental data for validation of neutron transport codes and nuclear cross-sections libraries used for LWR surveillance dosimetry analysis. The experimental device is made of 1 m 3 cubic plexiglass container filled with demineralized water. At one face of this cube, a 235 U neutron fission source system is screwed. The source device is made of a 235 U (93 % weight enriched) 18.55 x 16 cm 2 plate cladded with aluminium which is inserted in neutron beam emerging from the graphite gas-cooled BR1 reactor. Fission chambers ( 238 U(n,f), 232 Th(n,f), 237 Np(n,f) and 235 U(n,f)) are used to measure the flux traverses on the central axis of the water cube perpendicular to the fission sources. In this paper we will compare the experimental data to the calculated results using the S N , transport code DORT with the P 3 , ELXSIR library, based on ENDF/B-V, and the P 7 -BUGLE-93 library, based on ENDF/B-VI as well as the Monte-Carlo transport code TRIPOLI with a cross-section library based on ENDF/B IV and ENDF/B-VI. (authors)
Measurement of inelastic charmonium production at HERA
Energy Technology Data Exchange (ETDEWEB)
Steder, Michael
2008-09-15
This thesis presents measurements of inelastic photoproduction and electroproduction of J/{psi} mesons in ep scattering at HERA. The data was collected by the H1 detector during the HERA II running and corresponds to an integrated luminosity of L {approx} 166 pb{sup -1} in the photoproduction analysis and L {approx} 315 pb{sup -1} in the electroproduction analysis. In both analyses the elasticity of the J/{psi} meson is restricted to a medium range of 0.3 {<=} z {<=} 0.9. The kinematic range of the photoproduction analysis is defined by Q{sup 2} {approx} 0 GeV{sup 2}, 60 {<=}W{sub {gamma}}{sub p}{<=} 240 GeV and P{sub {tau}}{sub ,{psi}}{>=} 1 GeV{sup 2}, whereas the electroproduction analysis is restricted to 3.6 {<=} Q{sup 2} {<=} 100 GeV{sup 2}, 50 {<=}W{sub {gamma}}{sub p}{<=} 225 GeV, and P{sup *}{sub {tau}}{sub ,} {sub {psi}} {>=} 1 GeV. Here P{sup *}{sub {tau}}{sub ,} {sub {psi}} denotes the transverse momentum of the J/{psi} in the {gamma}p center of mass frame. In both kinematic ranges, single differential and double differential cross sections are measured with increased precision with respect to previous analyses. The polarisation of the J/{psi} mesons is studied in fits to the decay angular distributions cos({theta}{sup *}) and {phi}{sup *}. The measured cross sections are compared to different theoretical predictions. The most successful calculation in describing the data accounts for higher order corrections by using a k{sub {tau}} factorisation ansatz in the color singlet model (CSM). In addition, this thesis reviews the description of the data by calculations at leading and next to leading order in the CSM. The polarisation variables are compared to calculations in the factorisation ansatz in NRQCD, in addition to the leading order CSM predictions. (orig.)
A new approach to irreversibility in deep inelastic collisions
International Nuclear Information System (INIS)
Nemes, M.C.
1982-01-01
We use concepts of statistical mechanics to discuss the irreversible character of the experimental data in deep inelastic collisions. A definition of irreversibility proposed by Ruch permits a unified overview on current theories which describe these reactions. An information theoretical analysis of the data leads to a Fokker-Planck equation for the collective variables (excitation energy, charge and mass). The concept of mixing distance can serve as a quantitative measure to characterize the 'approach to equilibrium'. We apply it to the brownian motion as an illustration and also to the phenomenological analysis of deep inelastic scattering data with interesting results. (orig.)
Charm production and mass scales in deep inelastic processes
International Nuclear Information System (INIS)
Close, F.E.; Scott, D.M.; Sivers, D.
1976-07-01
Because of their large mass, the production of charmed particles offers the possibility of new insight into fundamental dynamics. An approach to deep inelastic processes is discussed in which Generalized Vector Meson Dominance is used to extend parton model results away from the strict Bjorken scaling limit into regions where mass scales play an important role. The processes e + e - annihilation, photoproduction, deep inelastic leptoproduction, photon-photon scattering and the production of lepton pairs in hadronic collisions are discussed. The GCMD approach provides a reasonably unified framework and makes specific predictions concerning the way in which these reactions reflect an underlying flavour symmetry, broken by large mass differences. (author)
Deep inelastic singlet structure functions and scaling violation
Energy Technology Data Exchange (ETDEWEB)
Wen-zhu, Li; Bing-xun, Hu
1984-02-01
The flavour singlet structure functions of deep inelastic scattering processes can yield more decisive tests of QCD than the non-singlet. We give analytical expression for flavour singlet structure functions through analysing the lepton-nucleon deep inelastic scattering processes by means of QCD and using Jacobi polynomials. This expression contains 4 to 5 parameters and shows the changes of the singlet structure functions with x and Q/sup 2/ very well. In QCD leading order, the conclusion is in reasonable agreement with experimental data.
Path integral theory and deep inelastic scattering of nuclei
International Nuclear Information System (INIS)
Neto, J.L.
1981-10-01
A formalism, based on Feynman's path integral, is developed and used in the theory of deep inelastic collisions of nuclei. Having shown how to express the propagator of the Wigner function of an isolated system as a (double) path integral in phase space, random processes are considered and the influence functional in interacting systems is discussed. A semi-classical description for the reduced Wigner and a generalized Langevin equation are given. Finally, the formalism is used in a random matrix model for deep inelastic collisions. (U.K.)
Theoretical interpretation of medium energy nucleon nucleus inelastic scattering
International Nuclear Information System (INIS)
Lagrange, Christian
1970-06-01
A theoretical study is made of the medium energy nucleon-nucleus inelastic scattering (direct interaction), by applying the distorted wave Born approximation such as can be deduced from the paired equation method. It is applied to the interpretation of the inelastic scattering of 12 MeV protons by 63 Cu; this leads us to make use of different sets of wave functions to describe the various states of the target nucleus. We analyze the nature of these states and the shape of the nucleon-nucleus interaction potential, and we compare the results with those obtained from other theoretical and experimental work. (author) [fr
On structural inelasticity of modal substitution in freight transport
DEFF Research Database (Denmark)
Rich, Jeppe; Kveiborg, Ole; Overgård, Christian Hansen
2011-01-01
alternative available. The paper investigates the magnitude of this ‘‘structural inelasticity” of modal substitution in freight transport due to a sparser layout of rail and ship-based freight networks compared to road. In the analysis we use a recent Scandinavian freight demand model covering more than 800...... zones. We find that the structural inelasticity is very significant – in particular for transportation over less than 500 km. Moreover, the inelasticity varies greatly with commodity groups and between OD pairs, and it depends strongly on the port and rail infrastructure. The results suggest that pure...
Spin-polarized inelastic tunneling through insulating barriers.
Lu, Y; Tran, M; Jaffrès, H; Seneor, P; Deranlot, C; Petroff, F; George, J-M; Lépine, B; Ababou, S; Jézéquel, G
2009-05-01
Spin-conserving hopping transport through chains of localized states has been evidenced by taking benefit of the high degree of spin-polarization of CoFeB-MgO-CoFeB magnetic tunnel junctions. In particular, our data show that relatively thick MgO barriers doped with boron favor the activation of spin-conserving inelastic channels through a chain of three localized states and leading to reduced magnetoresistance effects. We propose an extension of the Glazman-Matveev theory to the case of ferromagnetic reservoirs to account for spin-polarized inelastic tunneling through nonmagnetic localized states embedded in an insulating barrier.
Theory of single-spin inelastic tunneling spectroscopy.
Fernández-Rossier, J
2009-06-26
I show that recent experiments of inelastic scanning tunneling spectroscopy of single and a few magnetic atoms are modeled with a phenomenological spin-assisted tunneling Hamiltonian so that the inelastic dI/dV line shape is related to the spin spectral weight of the magnetic atom. This accounts for the spin selection rules and dI/dV spectra observed experimentally for single Fe and Mn atoms deposited on Cu2N. In the case of chains of Mn atoms it is found necessary to include both first and second-neighbor exchange interactions as well as single-ion anisotropy.
Solution of neutron slowing down equation including multiple inelastic scattering
International Nuclear Information System (INIS)
El-Wakil, S.A.; Saad, A.E.
1977-01-01
The present work is devoted the presentation of an analytical method for the calculation of elastically and inelastically slowed down neutrons in an infinite non absorbing homogeneous medium. On the basis of the Central limit theory (CLT) and the integral transform technique the slowing down equation including inelastic scattering in terms of the Green function of elastic scattering is solved. The Green function is decomposed according to the number of collisions. A formula for the flux at any lethargy O (u) after any number of collisions is derived. An equation for the asymptotic flux is also obtained
The lineshape of inelastic neutron scattering in the relaxor ferroelectrics
International Nuclear Information System (INIS)
Ivanov, M.A.; Kozlovski, M.; Piesiewicz, T.; Stephanovich, V.A.; Weron, A.; Wymyslowski, A.
2005-01-01
The possibilities of theoretical and experimental investigations of relaxor ferroelectrics by inelastic neutron scattering method are considered. The simple model to description of the peculiarities of inelastic neutron scattering lineshapes in ferroelectric relaxors is suggested. The essence of this model is to consider the interaction of the phonon subsystem of relaxor ferroelectrics with the ensemble of defects and impurities. The modification of the Latin Hypercube Sampling (LHS) method is presented. The optimization of planning of experiment by the modified LHS method is considered [ru
Transverse momentum in semi-inclusive deep inelastic scattering
International Nuclear Information System (INIS)
Ceccopieri, Federico Alberto; Trentadue, Luca
2006-01-01
Within the framework of perturbative quantum chromodynamics we derive the evolution equations for transverse momentum dependent distributions and apply them to the case of semi-inclusive deep inelastic scattering. The evolution equations encode the perturbative component of transverse momentum generated by collinear parton branchings. The current fragmentation is described via transverse momentum dependent parton densities and fragmentation functions. Target fragmentation instead is described via fracture functions. We present, to leading logarithmic accuracy, the corresponding semi-inclusive deep inelastic scattering cross-section, which applies to the entire phase space of the detected hadron. Some phenomenological implications and further developments are briefly outlined
An inelastic neutron scattering study of hematite nanoparticles
DEFF Research Database (Denmark)
Hansen, Mikkel Fougt; Klausen, Stine Nyborg; Lefmann, K
2003-01-01
We have studied the magnetic dynamics in nanocrystalline hematite by inelastic neutron scattering at the high-resolution time-of-flight spectrometer IRIS at ISIS. Compared to previous inelastic neutron scattering experiments an improvement of the resolution function is achieved and more detailed...... moment at the antiferromagnetic Bragg reflection. We have studied different weightings of the particle size distribution. The data and their temperature dependence can with good agreement be interpreted on the basis of the Neel-Brown theory for superparamagnetic relaxation and a model for the collective...
Inelastic pion scattering from 3H and 3He
International Nuclear Information System (INIS)
Berman, B.L.; Anderson, G.C.; Briscoe, W.J.; Mokhtari, A.; Petrov, A.M.; Sadler, M.E.; Barlow, D.B.; Nefkens, B.M.K.; Pillai, C.
1995-01-01
Cross sections have been measured for the inelastic scattering of π + and π - mesons from 3 H and 3 He in the 10-MeV interval just above the breakup thresholds, for incident pion energies of 142, 180, and 220 MeV and scattering angles of 40 degree, 60 degree, 80 degree, 90 degree, and 110 degree. No significant departure from unity is observed for the ratios of charge-symmetric cross sections. Comparisons are made with elastic pion-scattering and inelastic electron-scattering data
Higher Order Heavy Quark Corrections to Deep-Inelastic Scattering
Blümlein, Johannes; DeFreitas, Abilio; Schneider, Carsten
2015-04-01
The 3-loop heavy flavor corrections to deep-inelastic scattering are essential for consistent next-to-next-to-leading order QCD analyses. We report on the present status of the calculation of these corrections at large virtualities Q2. We also describe a series of mathematical, computer-algebraic and combinatorial methods and special function spaces, needed to perform these calculations. Finally, we briefly discuss the status of measuring αs (MZ), the charm quark mass mc, and the parton distribution functions at next-to-next-to-leading order from the world precision data on deep-inelastic scattering.
Users guide to the inelastic rotor spectrometer (IRS)
International Nuclear Information System (INIS)
Bunce, L.J.
1987-11-01
The paper is a users guide to the inelastic rotor spectrometer installed on the Harwell 136 Mev electron linear accelerator HELIOS. The spectrometer is designed to measure neutron inelastic scattering for energy transfers from 50 meV to 400 meV and covering a range of Q values from 1 to 15 A 0-1 . The guide contains a description of:- time-of-flight scales, run and sample changer control units, sample environment, detectors, rotor system, 600 Hz operation of rotor, a run, and data processing. (U.K.)
Highlights of electron-proton deep inelastic scattering at HERA
International Nuclear Information System (INIS)
Feltesse, J.
1996-02-01
Salient results on deep inelastic scattering from the H1 and ZEUS collaborations are reviewed. These include preliminary measurements of the proton structure function F 2 extending to new regimes at both high Q 2 and low Q 2 and x, studies of the hadronic final states and discussion on QCD interpretations of low x data. New determination of α s from jet rates in deep inelastic scattering based on 1994 data are presented. A consistent picture of the gluon density in the proton at low x from a variety of processes is obtained. (author)
Higher order heavy quark corrections to deep-inelastic scattering
International Nuclear Information System (INIS)
Bluemlein, J.; Freitas, A. de; Johannes Kepler Univ., Linz; Schneider, C.
2014-11-01
The 3-loop heavy flavor corrections to deep-inelastic scattering are essential for consistent next-to-next-to-leading order QCD analyses. We report on the present status of the calculation of these corrections at large virtualities Q 2 . We also describe a series of mathematical, computer-algebraic and combinatorial methods and special function spaces, needed to perform these calculations. Finally, we briefly discuss the status of measuring α s (M Z ), the charm quark mass m c , and the parton distribution functions at next-to-next-to-leading order from the world precision data on deep-inelastic scattering.
Inelastic neutron scattering of H2 adsorbed in HKUST-1
International Nuclear Information System (INIS)
Liu, Y.; Brown, C.M.; Neumann, D.A.; Peterson, V.K.; Kepert, C.J.
2007-01-01
A series of inelastic neutron scattering (INS) investigations of hydrogen adsorbed in activated HKUST-1 (Cu 3 (1,3,5-benzenetricarboxylate) 2 ) result in INS spectra with rich features, even at very low loading ( 2 :Cu). The distinct inelastic features in the spectra show that there are three binding sites that are progressively populated when the H 2 loading is less than 2.0 H 2 :Cu, which is consistent with the result obtained from previous neutron powder diffraction experiments. The temperature dependence of the INS spectra reveals the relative binding enthalpies for H 2 at each site
Hadronic inelastic cross sections from analyses of the elastic channel
International Nuclear Information System (INIS)
Beggio, P.C.; Martini, A.F.; Menon, M.J.
1997-01-01
We present a comparative analysis of the Inelastic Overlap Functions predicted by three models for elastic scattering: Chou and Yang, Henzi and Valin and Martini and Menon. The results are also compared with two model independent extractions (Amaldi-Schubert and Carvalho-Menon). We then calculate the predictions for the corresponding integrated inelastic cross-sections from the three models and compare the results with the experimental data on pp and pp scattering available above 10 GeV. Similarities and differences between all modes predictions are presented and discussed. (author)
EQUILIBRIUM OF TRUSS AND BEAM STRUCTURES OF INELASTIC MATERIALS
DEFF Research Database (Denmark)
Hagsten, Lars German
2017-01-01
A physically based method for the determination of equilibrium for structures with inelastic response is described. The method is based on minimisation of the potential energy. For structures with inelastic response, some of the applied energy is converted to non-mechanical energy. This part...... and shrinkage, as well as plastic strains from previous load scenarios, will also change the potential energy. The method is also capable of taken these effects into account. Three examples are included in order to support the physical understanding, and to illustrate the procedure for the application...
Li, Baihong; Dong, Ruifang; Zhou, Conghua; Xiang, Xiao; Li, Yongfang; Zhang, Shougang
2018-05-01
Selective two-photon microscopy and high-precision nonlinear spectroscopy rely on efficient spectral compression at the desired frequency. Previously, a Fresnel-inspired binary phase shaping (FIBPS) method was theoretically proposed for spectral compression of two-photon absorption and second-harmonic generation (SHG) with a square-chirped pulse. Here, we theoretically show that the FIBPS can introduce a negative quadratic frequency phase (negative chirp) by analogy with the spatial-domain phase function of Fresnel zone plate. Thus, the previous theoretical model can be extended to the case where the pulse can be transformed limited and in any symmetrical spectral shape. As an example, we experimentally demonstrate spectral compression in SHG by FIBPS for a Gaussian transform-limited pulse and show good agreement with the theory. Given the fundamental pulse bandwidth, a narrower SHG bandwidth with relatively high intensity can be obtained by simply increasing the number of binary phases. The experimental results also verify that our method is superior to that proposed in [Phys. Rev. A 46, 2749 (1992), 10.1103/PhysRevA.46.2749]. This method will significantly facilitate the applications of selective two-photon microscopy and spectroscopy. Moreover, as it can introduce negative dispersion, hence it can also be generalized to other applications in the field of dispersion compensation.
International Nuclear Information System (INIS)
Yeh, Naichia
2016-01-01
This paper illustrates details about the solar radiation distribution on the target of a two-stage solar concentrator that combines the Fresnel lens (FL) and the compound flat concentrator (CFC). The paper starts with a review of some FL development milestones such as the two-stage systems and the comparisons of flat vs. curved lenses in addition to the most noteworthy FL-based solar energy application, concentration photovoltaic (CPV). Through the review of the FL based CPV and two-stage concentrators, this study leads to the development of an algorithm to explore the spectrum distribution insight on the receiver of a two-stage (FL plus CFC) solar concentration system. It established the potential for using a correctly positioned 2nd stage reflector of right dimension to selectively redirect the desired spectrum on the target area so as to enhance the concentration flux intensity and uniformity at the same time. The study also helped to chart out the approximate locations of certain spectrum segments on the FL's target area, which is useful for exploring the spectrum control mechanism via the Fresnel lenses. - Highlights: • Map out the approximate locations of spectrum segments on FL's focal area. • Use the 2nd stage reflector to selectively reflect the desired spectrum on target. • Explore the spectrum distribution insight on FL solar concentrators' target area.
Vector correlations in rotationally inelastic molecular collisions
International Nuclear Information System (INIS)
Lemeshko, Mikhail
2011-01-01
characterizing the anisotropy of the hard-core part of the system's potential energy surface. The alignment moments obtained for He-OH(X 2 Π), He-O 2 (X 3 Σ), and He-CaH(X 2 Σ) allowed to identify the fingerprints of diffraction, which can be used to discern diffraction-driven stereodynamics in future experiments and exact computations. Analytic results for the Ne-NO(A 2 Σ) system were found to be in good agreement with experiment and exact computations for low rotational energy transfer; the discrepancy found for higher excitation channels could be traced back to the breakdown of the sudden approximation. The model was also applied to the k-j-k ' and k-j-k ' -j ' correlations in rotationally inelastic Ar-NO(X 2 Π) scattering. It was shown that preparing the reagents with polarized angular momentum j makes it possible to significantly alter the collision dynamics and stereodynamics. In the final part of the thesis the analytic theory was extended to the study of multiple scattering of matter waves propagating through atomic and molecular gases. The combination of the Fraunhofer model with the semiclassical approximation to account, respectively, for the repulsive and attractive part of the potential energy surface resulted in a simple analytic formula, which agree well with experiment for the refraction of a Li beam passing through Xe gas. (orig.)
Vector correlations in rotationally inelastic molecular collisions
Energy Technology Data Exchange (ETDEWEB)
Lemeshko, Mikhail
2011-04-13
diffractive part of the scattering amplitude which is governed by a single Legendre moment characterizing the anisotropy of the hard-core part of the system's potential energy surface. The alignment moments obtained for He-OH(X{sup 2}{pi}), He-O{sub 2}(X{sup 3}{sigma}), and He-CaH(X{sup 2}{sigma}) allowed to identify the fingerprints of diffraction, which can be used to discern diffraction-driven stereodynamics in future experiments and exact computations. Analytic results for the Ne-NO(A{sup 2}{sigma}) system were found to be in good agreement with experiment and exact computations for low rotational energy transfer; the discrepancy found for higher excitation channels could be traced back to the breakdown of the sudden approximation. The model was also applied to the k-j-k{sup '} and k-j-k{sup '}-j{sup '} correlations in rotationally inelastic Ar-NO(X{sup 2}{pi}) scattering. It was shown that preparing the reagents with polarized angular momentum j makes it possible to significantly alter the collision dynamics and stereodynamics. In the final part of the thesis the analytic theory was extended to the study of multiple scattering of matter waves propagating through atomic and molecular gases. The combination of the Fraunhofer model with the semiclassical approximation to account, respectively, for the repulsive and attractive part of the potential energy surface resulted in a simple analytic formula, which agree well with experiment for the refraction of a Li beam passing through Xe gas. (orig.)
Inelastic diffraction nuclear processes with redistribution of particles
International Nuclear Information System (INIS)
Sitenko, A.G.; Goryachij, V.V.; Peresypkin, V.V.
1979-01-01
The inelastic nuclear processes at high energies with redistribution of particles are described within the framework of the diffraction approach. The capture processes (p,d) and (p,p'n) generated by the high energy nucleon collision with nuclei are considered. The angular distribution of 4 He(p,d) 3 He reaction is calculated and compared with experimental data
Inelastic dark matter in light of DAMA/LIBRA
International Nuclear Information System (INIS)
Chang, Spencer; Weiner, Neal; Kribs, Graham D.; Tucker-Smith, David
2009-01-01
Inelastic dark matter, in which weakly interacting massive particle (WIMP)-nucleus scatterings occur through a transition to an excited WIMP state ∼100 keV above the ground state, provides a compelling explanation of the DAMA annual modulation signal. We demonstrate that the relative sensitivities of various dark matter direct detection experiments are modified such that the DAMA annual modulation signal can be reconciled with the absence of a reported signal at CDMS-Soudan, XENON10, ZEPLIN, CRESST, and KIMS for inelastic WIMPs with masses O(100 GeV). We review the status of these experiments, and make predictions for upcoming ones. In particular, we note that inelastic dark matter leads to highly suppressed signals at low energy, with most events typically occurring between 20 and 45 keV (unquenched) at xenon and iodine experiments, and generally no events at low (∼10 keV) energies. Suppressing the background in this high-energy region is essential to testing this scenario. The recent CRESST data suggest seven observed tungsten events, which is consistent with expectations from this model. If the tungsten signal persists at future CRESST runs, it would provide compelling evidence for inelastic dark matter, while its absence should exclude it.
Quasiparticle-phonon coupling in inelastic proton scattering
International Nuclear Information System (INIS)
Weissbach, B.
1980-01-01
Multistep-processes in inelastic proton scattering from 89 Y are analyzed by using CCBA and DWBA on a quasiparticle phonon nuclear structure model. Indirect excitations caused by quasiparticle phonon coupling effects are found to be very important for the transition strengths and the shape of angular distributions. Core excitations are dominant for the higher order steps of the reaction. (author)
Measuring isospin mixing in nuclei using π+- inelastic scattering
International Nuclear Information System (INIS)
Cottingame, W.B.; Braithwaite, W.J.; Morris, C.L.
1979-01-01
A new strongly isospin-mixed doublet has been found in 12 C near 19.5 MeV. in a comparison of π - and π + inelastic scattering at 180 MeV, The present techniques may be universally employable, at least in self-conjugate nuclei, in extracting isospin-mixing matrix elements
Inelastic Neutron Scattering Investigations of the Magnetic Excitations
DEFF Research Database (Denmark)
Feile, R; Kjems, Jørgen; Hauser, A.
1984-01-01
The magnetic excitations perpendicular to the antiferromagnetic chains in CsVX3 (X = Cl, Br, I) have been measured in the ordered state by inelastic neutron scattering. The dispersion relations and intensity distributions are those expected for ordinary spin waves in a triangular xy-model....
Transport theory of deep-inelastic collisions between heavy nuclei
International Nuclear Information System (INIS)
Ayik, S.; Noerenberg, W.; Schuermann, B.
1975-01-01
In collisions between heavy nuclei, the major part of the total cross-section is due to deep-inelastic processes. These processes have been studied within a quantum-statistical approach leading to transport equations of the Fokker-Planck type (generalized diffusion equation). Transport coefficients have been studied within a model. (orig./WL) [de
Contribution of the NN inelasticity into photodisintegration of the deuteron
International Nuclear Information System (INIS)
Sadovnikova, V.A.
1996-01-01
The technique of dispersion integration over the mass of composite particle is used to describe the reaction of the deuteron photodisintegration. The influence of the final state interaction on the total cross section, calculated with and without inelasticity is investigated. Numerical results depend on the choice of the vertex for the isobar photoproduction [ru
Elastic and inelastic photon scattering on the atomic nuclei
International Nuclear Information System (INIS)
Piskarev, I.M.
1982-01-01
Works on investigation of elastic and inelastic scattering of photons on heavy and intermediate nuclei are briefly reviewed. Theoretical problems of nuclear and electron Tompson, Releev and Delbrueck scatterings as well as nuclear resonance scattering are briefly discussed. It is shown that differential cross section of coherent elastic scattering is expressed by means of partial amplitudes of shown processes. Experimental investigations on elastic scattering in the region of threshold energies of photonucleon reactions are described. Problems of theoretical description of elastic scattering in different variants of collective models are considered. Discussed are works, investigating channels of inelastic photon scattering with excitation of nuclear Raman effect. It is noted that to describe channels of inelastic photon scattering it is necessary to use models, that correctly regard the microscopic structure of giant resonance levels to obtain information on the nature of these levels. Investigations of processes of photon elastic and inelastic scattering connected with fundamental characteristics of atomic nucleus, permit to obtain valuable spectroscopic information on high-lying levels of nucleus. Detail investigation of photon scattering in a wide range of energies is necessary [ru
Scaled momentum spectra in deep inelastic scattering at HERA
Abramowicz, H.; Abt, I.; Adamczyk, L.; Adamus, M.; Antonelli, S.; Antonioli, P.; Antonov, A.; Arneodo, M.; Aushev, V.; Aushev, Y.; Bachynska, O.; Bamberger, A.; Barakbaev, A. N.; Barbagli, G.; Bari, G.; Barreiro, F.; Bartsch, D.; Basile, M.; Behnke, O.; Behr, J.; Behrens, U.; Bellagamba, L.; Bertolin, A.; Bhadra, S.; Bindi, M.; Blohm, C.; Bold, T.; Boos, E. G.; Borodin, M.; Borras, K.; Boscherini, D.; Boutle, S. K.; Brock, I.; Brownson, E.; Brugnera, R.; Bruemmer, N.; Bruni, A.; Bruni, G.; Brzozowska, B.; Bussey, P. J.; Butterworth, J. M.; Bylsma, B.; Caldwell, A.; Capua, M.; Carlin, R.; Catterall, C. D.; Chekanov, S.; Chwastowski, J.; Ciborowski, J.; Pellegrino, A.
Charged particle production has been studied in neutral current deep inelastic ep scattering with the ZEUS detector at HERA using an integrated luminosity of 0.44 fb(-1). Distributions of scaled momenta in the Breit frame are presented for particles in the current fragmentation region. The evolution
Benchmarking the inelastic neutron scattering soil carbon method
The herein described inelastic neutron scattering (INS) method of measuring soil carbon was based on a new procedure for extracting the net carbon signal (NCS) from the measured gamma spectra and determination of the average carbon weight percent (AvgCw%) in the upper soil layer (~8 cm). The NCS ext...
Resonant inelastic x-ray scattering studies of elementary excitations
Ament, Lucas Johannes Peter (Luuk)
2010-01-01
Resonant Inelastic X-ray Scattering (RIXS) is an X-ray in, X-ray out technique that enables one to study the dispersion of excitations in solids. In this thesis, we investigated how various elementary excitations of transition metal oxides show up in RIXS spectra.
Inclusive deep inelastic scattering at HERA and related phenomenology
International Nuclear Information System (INIS)
Zomer, F.
1999-12-01
Recent measurements of inclusive deep inelastic scattering differential cross-section in the range 1.5 GeV 2 ≤ Q 2 ≤ 30000 GeV 2 and 5.10 -6 ≤ x ≤ 0.65 are presented. Phenomenological analyses performed from these measurements are also described. (author)
Generation of discrete inelastic and elastic transfer matrix
International Nuclear Information System (INIS)
Garcia, R.D.M.; Santina, M.D.
1985-01-01
A technique developed for the calculation of the isotropic and linearly anisotropic components components of elastic and discrete inelastic transfer matrices is presented in this work. The implementation of the technique is discussed in detail and numerical results obtained for some examples are compared with results reported in the literature or generated with the use of several processing codes. (author) [pt
Studies of magnetism with inelastic scattering of cold neutrons
International Nuclear Information System (INIS)
Jacrot, B.
1964-01-01
Inelastic scattering of cold neutrons can be used to study some aspects of magnetism: spins waves, exchange integrals, vicinity of Curie point. After description of the experimental set-up, several experiments, in the fields mentioned above, are analysed. (author) [fr
Hadronic parity violation and inelastic electron-deuteron scattering
International Nuclear Information System (INIS)
Liu, C.-P.; Prezeau, G.; Ramsey-Musolf, M.J.
2003-01-01
We compute contributions to the parity-violating (PV) inelastic electron-deuteron scattering asymmetry arising from hadronic PV. While hadronic PV effects can be relatively important in PV threshold electrodisintegration, we find that they are highly suppressed at quasielastic kinematics. The interpretation of the PV quasielastic asymmetry is, thus, largely unaffected by hadronic PV
Longitudinal and transverse polarizations in the deep inelastic reactions
International Nuclear Information System (INIS)
Bressan, A.
1996-07-01
This course is an introduction to the dominant effects of longitudinal and transverse spin in deep inelastic reactions. Only the effects present to the 'leading twist' are attacked. The mass and transverse impulsion of partons are neglected. We will attach to bring out the respective specificities of longitudinal and transverse polarizations. (N.C.)
Lattice dynamics of solid deuterium by inelastic neutron scattering
DEFF Research Database (Denmark)
Nielsen, Mourits; Bjerrum Møller, Hans
1971-01-01
The dispersion relations for phonons in solid ortho-deuterium have been measured at 5 °K by inelastic neutron scattering. The results are in good agreement with recent calculations in which quantum effects are taken into account. The data have been fitted to a third-neighbor general force model...
Instantons in the QCD vacuum and in deep inelastic scattering
International Nuclear Information System (INIS)
Ringwald, A.; Schrempp, F.
1999-01-01
We give a brief status report on our on-going investigation of the prospects to discover QCD instantons in deep inelastic scattering (DIS) at HERA. A recent high-quality lattice study of the topological structure of the QCD vacuum is exploited to provide crucial support of our predictions for DIS, based on instanton perturbation theory
Spectrometer for neutron inelastic scattering investigations of microsamples
International Nuclear Information System (INIS)
Balagurov, A.M.; Kozlenko, D.P.; Platonov, S.L.; Savenko, B.N.; Glazkov, V.P.; Krasnikov, Yu.M.; Naumov, I.V.; Pukhov, A.V.; Somenkov, V.A.; Syrykh, G.F.
1997-01-01
A new neutron spectrometer for investigation of inelastic neutron scattering on polycrystal microsamples under high pressure in sapphire and diamond anvils cells is described. The spectrometer is operating at the IBR-2 pulsed reactor in JINR. Parameters and methodical peculiarities of the spectrometer and the examples of experimental studies are given. (author)
Inelastic neutron scattering from non-framework species within zeolites
International Nuclear Information System (INIS)
Newsam, J.M.; Brun, T.O.; Trouw, F.; Iton, L.E.; Curtiss, L.A.
1990-01-01
Inelastic and quasielastic neutron scattering have special advantages for studying certain of the motional properties of protonated or organic species within zeolites and related microporous materials. In this paper these advantages and various experimental methods are outlined, and illustrated by measurements of torsional vibrations and rotational diffusion of tetramethylammonium (TMA) cations occluded within zeolites TMA-sodalite, omega, ZK-4 and SAPO-20
Some comments about polarization in deep inelastic processes
International Nuclear Information System (INIS)
Bajpai, R.P.
1983-01-01
One can fit baryon production in deep inelastic processes in terms of baryon fragmentation functions. It appears that for z > 0.3, the individual quark materializes into a baryon by picking up the appropriate diquark. The spin and isospin properties of the diquark will give definite asymmetry in baryon production in terms of only three unknown parameters. 4 references, 1 table
Dynamics of liquid N2 studied by neutron inelastic scattering
DEFF Research Database (Denmark)
Pedersen, Karen Schou; Carneiro, Kim; Hansen, Flemming Yssing
1982-01-01
Neutron inelastic-scattering data from liquid N2 at wave-vector transfer κ between 0.18 and 2.1 Å-1 and temperatures ranging from T=65-77 K are presented. The data are corrected for the contribution from multiple scattering and incoherent scattering. The resulting dynamic structure factor S (κ,ω)...
Status of the development of electron volt inelastic neutron spectroscopy
International Nuclear Information System (INIS)
Newport, R.J.; Taylor, A.D.; Williams, W.G.
1984-05-01
High energy inelastic neutron scattering spectroscopy is reviewed in the light of material presented at the 'High Energy Excitations in Condensed Matter' (HEECM) Workshop, held at Los Alamos National Laboratory 13-15 February 1984. Particular attention is paid to the development of instrumentation based on nuclear resonance analysers. (author)
Polarized neutron inelastic scattering experiments on spin dynamics
International Nuclear Information System (INIS)
Kakurai, Kazuhisa
2016-01-01
The principles of polarized neutron scattering are introduced and examples of polarized neutron inelastic scattering experiments on spin dynamics investigation are presented. These examples should demonstrate the importance of the polarized neutron utilization for the investigation of non-trivial magnetic ground and excited states in frustrated and low dimensional quantum spin systems. (author)
Inelastic surface vibrations versus energy-dependent nucleus ...
Indian Academy of Sciences (India)
Limitations of the static Woods–Saxon potential and the applicability of the energy dependent Woods–Saxon potential (EDWSP) model within the framework of one-dimensional Wong formula to explore the sub-barrier fusion data are highlighted. The inelastic surface excitations of the fusing nuclei are found to be ...
Quantum chromodynamics and deep inelastic e - N scattering at TRISTAN
International Nuclear Information System (INIS)
Muta, Taizo
1979-04-01
An introductory survey is given on the formulation of QCD in deep inelastic lepton-hadron scatterings. Typical predictions of QCD are presented in the kinematical region of TRISTAN, including detailed descriptions of the scaling violation, QCD correction to the current algebra sum rules, problem of quark masses and higher order effects. Some suggestions for experiments at TRISTAN are made. (author)
Inelastic scattering and local heating in atomic gold wires
DEFF Research Database (Denmark)
Frederiksen, Thomas; Brandbyge, Mads; Lorente, N.
2004-01-01
We present a method for including inelastic scattering in a first-principles density-functional computational scheme for molecular electronics. As an application, we study two geometries of four-atom gold wires corresponding to two different values of strain and present results for nonlinear...
Inelastic surface vibrations versus energy-dependent nucleus ...
Indian Academy of Sciences (India)
Abstract. Limitations of the static Woods–Saxon potential and the applicability of the energy- dependent Woods–Saxon potential (EDWSP) model within the framework of one-dimensional. Wong formula to explore the sub-barrier fusion data are highlighted. The inelastic surface exci- tations of the fusing nuclei are found to ...
Measurement of inelastic J/ψ production in deep inelastic ep scattering at HERA
International Nuclear Information System (INIS)
Antonov, A.
2007-08-01
This thesis presents a measurement of the inelastic production of J/ψ mesons in ep collisions with the ZEUS detector at HERA using an integrated luminosity of 109 pb -1 . The J/ψ mesons were identified using the decay channel J/ψ → μ + μ - . The measurements were performed in the kinematic range 2 2 2 , 50 lab 2 is the virtuality of the exchanged photon, W is the photon-proton centre-of-mass energy, z is the fraction of the photon energy carried by the J/ψ meson in the proton rest frame and Y lab is the rapidity of the J/ψ in the laboratory frame. The measured cross sections are compared to theoretical predictions within the non-relativistic QCD framework including colour-singlet and colour-octet contributions, as well as to predictions based on the k T -factorisation approach. Calculations of the colour-singlet process generally agree with the data, whereas inclusion of colour-octet terms spoils this agreement. As a technical part of this thesis, the Straw-Tube Tracker (STT) GEANT simulation and track reconstruction software developed. Studies of the STT performance with MC data and real data presented. (orig.)
Measurement of inelastic J/{psi} production in deep inelastic ep scattering at HERA
Energy Technology Data Exchange (ETDEWEB)
Antonov, A.
2007-08-15
This thesis presents a measurement of the inelastic production of J/{psi} mesons in ep collisions with the ZEUS detector at HERA using an integrated luminosity of 109 pb{sup -1}. The J/{psi} mesons were identified using the decay channel J/{psi} {yields} {mu}{sup +}{mu}{sup -}. The measurements were performed in the kinematic range 2
Multi-Fresnel lenses pumping approach for improving high-power Nd:YAG solar laser beam quality.
Liang, Dawei; Almeida, Joana
2013-07-20
To significantly improve the present-day high-power solar laser beam quality, a three-stage multi-Fresnel lenses approach is proposed for side-pumping either a Nd:YAG single-crystal or a core-doped Sm(3+)Nd:YAG ceramic rod. Optimum pumping and laser beam parameters are found through ZEMAX and LASCAD numerical analysis. The proposed scheme offers a uniform absorption profile along the rod. 167 W laser power can be achieved, corresponding to 29.3 W/m(2) collection efficiency. High brightness figure of merit of 8.34 W is expected for the core-doped rod within a convex-concave resonator, which is 1300 times higher than that of the most-recent high-power solar laser.
International Nuclear Information System (INIS)
Kraemer, G.; Einighammer, H.J.; Elwert, G.; Braeuninger, H.; Fink, H.H.; Truemper, J.
1978-01-01
Soft X-ray photographs of the Sun taken at O VII 21.6 A and in a spectral band ranging from 13.2 to 22.1 A have been analysed in order to establish spatially resolved maps of temperature and emission measure for several active regions in the corona. The photographs were taken on 11 March, 1971, and on 2 March, 1972, with Fresnel zone plate cameras which were flown on ESRO and NRI sounding rockets. The authors deal with those aspects of the instrumentation which are important for setting up a suitable image analysis procedure. The characteristics of the wavelength dependent image formation by zone plates combined with absorption filters are discussed. Results of the calibration of the X-ray film are given. Then a specific iterative data reduction procedure is described and finally the resulting maps of temperature and emission measure are presented for a selected active region. (Auth.)
Healy, John J; Sheridan, John T
2011-05-01
The product of the spatial and spatial frequency extents of a wave field has proven useful in the analysis of the sampling requirements of numerical simulations. We propose that the ratio of these quantities is also illuminating. We have shown that the distance at which the so-called "direct method" becomes more efficient than the so-called "spectral method" for simulations of Fresnel transforms may be written in terms of this space-bandwidth ratio. We have proposed generalizations of these algorithms for numerical simulations of general ABCD systems and derived expressions for the "transition space-bandwidth ratio," above which the generalization of the spectral method is the more efficient algorithm and below which the generalization of the direct method is preferable.
Piszczor, M. F.; Swartz, C. K.; O'Neill, M. J.; Mcdanal, A. J.; Fraas, L. M.
1990-01-01
NASA Lewis and ENTECH have been developing a high-efficiency, lightweight space photovoltaic concentrator array. The emphasis of the program has shifted to fabrication and testing of the minidome Fresnel lens and other array components. Protototype lenses have been tested for optical efficiency, with results around 90 percent, and tracking error performance. The results of these tests have been very consistent with the predicted analytical performance. Work has also progressed in the fabrication of the array support structure. Recent advances in 30 percent efficient stacked cell technology will have a significant effect on the array performance. It is concluded that near-term array performance goals of 300 W/sq m and 100 W/kg are feasible.
González, Juan C
2009-04-10
A new type of convex Fresnel lens for linear photovoltaic concentration systems is presented. The lens designed with this method reaches 100% of geometrical optical efficiency, and the ratio (Aperture area)/(Receptor area) is up to 75% of the theoretical limit. The main goal of the design is high uniformity of the radiation on the cell surface for each input angle inside the acceptance. The ratio between the maximum and the minimum irradiance on points of the solar cell is less than 2. The lens has been designed with the simultaneous multiple surfaces (SMS) method of nonimaging optics, and ray tracing techniques have been used to characterize its performance for linear symmetry systems.
Multilayer on-chip stacked Fresnel zone plates: Hard x-ray fabrication and soft x-ray simulations
Energy Technology Data Exchange (ETDEWEB)
Li, Kenan; Wojcik, Michael J.; Ocola, Leonidas E.; Divan, Ralu; Jacobsen, Chris
2015-11-01
Fresnel zone plates are widely used as x-ray nanofocusing optics. To achieve high spatial resolution combined with good focusing efficiency, high aspect ratio nanolithography is required, and one way to achieve that is through multiple e-beam lithography writing steps to achieve on-chip stacking. A two-step writing process producing 50 nm finest zone width at a zone thickness of 1.14 µm for possible hard x-ray applications is shown here. The authors also consider in simulations the case of soft x-ray focusing where the zone thickness might exceed the depth of focus. In this case, the authors compare on-chip stacking with, and without, adjustment of zone positions and show that the offset zones lead to improved focusing efficiency. The simulations were carried out using a multislice propagation method employing Hankel transforms.
Inelastic scattering of 275 keV neutrons by silver
International Nuclear Information System (INIS)
Litvinsky, L.L.; Zhigalov, Ya.A.; Krivenko, V.G.; Purtov, O.A.; Sabbagh, S.
1997-01-01
Neutron total, elastic and inelastic scattering cross-scattering of Ag at the E n = 275 KeV neutron energy were measured by using the filtered neutron beam of the WWR-M reactor in Kiev. The d-neutron strength function S n2 of Ag was determined from the analysis of all available data in the E n ≤ keV energy region on neutron inelastic scattering cross-sections with excitation of the first isomeric levels I π m = 7/2 + , E m ∼ 90 keV of 107,109 Ag: S n2 = (1.03 ± 0.19) · 10 -4 . (author). 10 refs, 3 figs
Inelastic photoproduction of ω and rho+-mesons
International Nuclear Information System (INIS)
Nelson, C.A. Jr.; May, E.N.; Abramson, J.; Andrews, D.E.; Harvey, J.; Lobkowicz, F.; Singer, M.N.; Thorndike, E.H.; Nordberg, M.E. Jr.
1978-01-01
We report measurements of inelastic photoproduction of ω and rho +- mesons from hydrogen and deuterium at incident photon energies in the range 7.5-10.5 GeV. For ωΔ and rho - Δ ++ production differential cross sections dsigma/dt' and spin density matrices are presented. For higher missing masses the cross sections dsigma/dM/sub X/ 2 and invariant structure functions F(x) are also given. The data are compared to a one-pion-exchange model. We conclude that pion exchange is dominant for inelastic ω photoproduction, but unimportant for rho +- during annealing, even though the resistively determined transport scattering time increased by a factor of 7.8 during annealing. Orbital depairing was found to follow a relation zeta = zeta 0 + αH 2 and to increase with annealing in a manner expected from the change in mean free path determined from measurements of H/sub cnu/
Search for magnetic inelastic dark matter with XENON100
Energy Technology Data Exchange (ETDEWEB)
Aprile, E.; Anthony, M. [Physics Department, Columbia University, New York, NY 10027 (United States); Aalbers, J.; Breur, P.A.; Brown, A. [Nikhef and the University of Amsterdam, Science Park, 1098XG Amsterdam (Netherlands); Agostini, F.; Bruno, G. [INFN-Laboratori Nazionali del Gran Sasso and Gran Sasso Science Institute, 67100 L' Aquila (Italy); Alfonsi, M. [Institut für Physik and Exzellenzcluster PRISMA, Johannes Gutenberg-Universität Mainz, 55099 Mainz (Germany); Amaro, F.D. [LIBPhys, Department of Physics, University of Coimbra, 3004-516 Coimbra (Portugal); Arneodo, F.; Benabderrahmane, M.L. [New York University Abu Dhabi, Abu Dhabi (United Arab Emirates); Barrow, P.; Baudis, L. [Physik-Institut, University of Zurich, 8057 Zurich (Switzerland); Bauermeister, B.; Calvén, J. [Oskar Klein Centre, Department of Physics, Stockholm University, AlbaNova, Stockholm SE-10691 (Sweden); Berger, T.; Brown, E. [Department of Physics, Applied Physics and Astronomy, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Bruenner, S. [Max-Planck-Institut für Kernphysik, 69117 Heidelberg (Germany); Budnik, R. [Department of Particle Physics and Astrophysics, Weizmann Institute of Science, Rehovot 7610001 (Israel); Bütikofer, L., E-mail: lukas.buetikofer@lhep.unibe.ch, E-mail: xenon@lngs.infn.it [Physikalisches Institut, Universität Freiburg, 79104 Freiburg (Germany); and others
2017-10-01
We present the first search for dark matter-induced delayed coincidence signals in a dual-phase xenon time projection chamber, using the 224.6 live days of the XENON100 science run II. This very distinct signature is predicted in the framework of magnetic inelastic dark matter which has been proposed to reconcile the modulation signal reported by the DAMA/LIBRA collaboration with the null results from other direct detection experiments. No candidate event has been found in the region of interest and upper limits on the WIMP's magnetic dipole moment are derived. The scenarios proposed to explain the DAMA/LIBRA modulation signal by magnetic inelastic dark matter interactions of WIMPs with masses of 58.0 GeV/c{sup 2} and 122.7 GeV/c{sup 2} are excluded at 3.3 σ and 9.3 σ, respectively.
Application of Van Hove theory to fast neutron inelastic scattering
International Nuclear Information System (INIS)
Stanicicj, V.
1974-11-01
The Vane Hove general theory of the double differential scattering cross section has been used to derive the particular expressions of the inelastic fast neutrons scattering kernel and scattering cross section. Since the considered energies of incoming neutrons being less than 10 MeV, it enables to use the Fermi gas model of nucleons. In this case it was easy to derive an analytical expression for the time-dependent correlation function of the nucleus. Further, by using an impulse approximation and a short-collision time approach, it was possible to derive the analytical expression of the scattering kernel and scattering cross section for the fast neutron inelastic scattering. The obtained expressions have been used for Fe nucleus. It has been shown a surprising agreement with the experiments. The main advantage of this theory is in its simplicity for some practical calculations and for some theoretical investigations of nuclear processes
Dijet production in diffractive deep inelastic scattering at HERA
International Nuclear Information System (INIS)
Chekanov, S.; Derrick, M.; Magill, S.
2007-08-01
The production of dijets in diffractive deep inelastic scattering has been measured with the ZEUS detector at HERA using an integrated luminosity of 61 pb -1 . The dijet cross section has been measured for virtualities of the exchanged virtual photon, 5 2 2 , and γ * p centre-of-mass energies, 100 T algorithm in the γ * p frame, were required to have a transverse energy E * T,jet >4 GeV and the jet with the highest transverse energy was required to have E * T,jet >5 GeV. All jets were required to be in the pseudorapidity range -3.5 * jet <0. The differential cross sections are compared to leading-order predictions and next-to-leading- order QCD calculations based on recent diffractive parton densities extracted from inclusive diffractive deep inelastic scattering data. (orig.)
Near quantum limited amplification from inelastic Cooper-pair tunneling
Hofheinz, Max; Jebari, Salha; Blanchet, Florian; Grimm, Alexander; Hazra, Dibyendu; Albert, Romain; Portier, Fabien
Josephson parametric amplifiers approach quantum-limited noise performance but require strong external microwave pump tones which make them more difficult to use than DC powered amplifiers: The pump tone can affect the device under test and requires expensive room-temperature equipment. Inelastic Cooper pair tunneling processes through a small DC voltage-biased Josephson junction, where a tunneling Cooper pair dissipates its energy 2 eV in the form of two photons are reminiscent of parametric down conversion. We show that these processes can be used to provide amplification near the quantum limit without external microwave pump tone. We explain the measured gain and noise based on the P (E) theory of inelastic Cooper pair tunneling and general fluctuation-dissipation relations.
Deep inelastic processes. Phenomenology. Quark-parton model
International Nuclear Information System (INIS)
Ioffe, B.L.; Lipatov, L.N.; Khoze, V.A.
1983-01-01
Main theoretical approaches and experimental results related to deep inelastic processes are systematically outlined: electroproduction, neutrino scattering on nucleon, electron-positron pairs annihilation into hadron γγ collisions, production of lepton pairs in hadron collisions with a large effective mass or hadrons with large transverse momenta. Kinematics and phenomenology, space-time description of deep inelastic processes, sum rules, parton and quark-parton models are considered. The experiment is briefly discussed in the book. It is performed from the stand point of comparing it with the theory, experimental data are given as of June, 1982. Since the time of accomplishing the study on the manuscript a number of new experimental results not changing however the statements made in the book appeared. Principal consists in experiments with colliding proton-antiproton beams in CERN, which resulted in discovery of intermediate W-bozon
Computer modeling of inelastic wave propagation in porous rock
International Nuclear Information System (INIS)
Cheney, J.A.; Schatz, J.F.; Snell, C.
1979-01-01
Computer modeling of wave propagation in porous rock has several important applications. Among them are prediction of fragmentation and permeability changes to be caused by chemical explosions used for in situ resource recovery, and the understanding of nuclear explosion effects such as seismic wave generation, containment, and site hardness. Of interest in all these applications are the distance from the source to which inelastic effects persist and the amount of porosity change within the inelastic region. In order to study phenomena related to these applications, the Cam Clay family of models developed at Cambridge University was used to develop a similar model that is applicable to wave propagation in porous rock. That model was incorporated into a finite-difference wave propagation computer code SOC. 10 figures, 1 table
Studies in deep inelastic scattering and vector meson photoproduction
International Nuclear Information System (INIS)
Busenitz, J.K.
1985-01-01
The first part of this thesis is devoted to a space-time analysis of deep inelastic scattering from protons at rest. Techniques are developed for identifying important space-time regions. These are then applied to obtain a space-time picture of deep inelastic scattering in the leading logarithmic approximation of QCD, Physical mechanisms responsible for the space-time picture are discussed. In the second part of this thesis he reports on the observations of elastic omega photoproduction from hydrogen by Fermilab Experiment-401. The omega was detected via its decay into the π + π - π 0 channel. Measurements of the energy, momentum transfer, and angular dependence of the cross section have been made for photon energies between 60 and 225 GeV
Inelastic Boosted Dark Matter at direct detection experiments
Giudice, Gian F.; Kim, Doojin; Park, Jong-Chul; Shin, Seodong
2018-05-01
We explore a novel class of multi-particle dark sectors, called Inelastic Boosted Dark Matter (iBDM). These models are constructed by combining properties of particles that scatter off matter by making transitions to heavier states (Inelastic Dark Matter) with properties of particles that are produced with a large Lorentz boost in annihilation processes in the galactic halo (Boosted Dark Matter). This combination leads to new signals that can be observed at ordinary direct detection experiments, but require unconventional searches for energetic recoil electrons in coincidence with displaced multi-track events. Related experimental strategies can also be used to probe MeV-range boosted dark matter via their interactions with electrons inside the target material.
Revealing inner shell dynamics with inelastic X-ray scattering
International Nuclear Information System (INIS)
Franck, C.
1990-01-01
One of the many opportunities provided by the Advanced Photon Source (APS) is to extend the study of intra-atomic dynamics. As a means of testing dynamic response, inelastic x-ray scattering is particularly promising since it allows us to independently vary the period of the exciting field in both space and time. As an example of this type of work, the author presents experiments performed at the Cornell High Energy Synchrotron Source (CHESS) laboratory, a prototype for the APS. This was inner shell inelastic scattering with a twist: in order to explore a new distance scale an x-ray fluorescence trigger was employed. Aside for the atomic insight gained, the experiment taught them the importance of the time structure of the synchrotron beam for coincidence experiments which are dominated by accidental events
Direct evidence for inelastic neutron 'acceleration' by 177Lum
International Nuclear Information System (INIS)
Roig, O.; Meot, V.; Rosse, B.; Belier, G.; Daugas, J.-M.; Morel, P.; Letourneau, A.; Menelle, A.
2011-01-01
The inelastic neutron acceleration cross section on the long-lived metastable state of 177 Lu has been measured using a direct method. High-energy neutrons have been detected using a specially designed setup placed on a cold neutron beam extracted from the ORPHEE reactor in Saclay. The 146±19 b inelastic neutron acceleration cross section in the ORPHEE cold neutron flux confirms the high cross section for this process on the 177 Lu m isomer. The deviation from the 258±58 b previously published obtained for a Maxwellian neutron flux at a 323 K temperature could be explained by the presence of a low energy resonance. Resonance parameters are deduced and discussed.
Fast Neutron Elastic and Inelastic Scattering of Vanadium
Energy Technology Data Exchange (ETDEWEB)
Holmqvist, B; Johansson, S G; Lodin, G; Wiedling, T
1969-11-15
Fast neutron scattering interactions with vanadium were studied using time-of-flight techniques at several energies in the interval 1.5 to 8.1 MeV. The experimental differential elastic scattering cross sections have been fitted to optical model calculations and the inelastic scattering cross sections have been compared with Hauser-Feshbach calculations, corrected for the fluctuation of compound-nuclear level widths.
Radiative corrections to neutrino deep inelastic scattering revisited
International Nuclear Information System (INIS)
Arbuzov, Andrej B.; Bardin, Dmitry Yu.; Kalinovskaya, Lidia V.
2005-01-01
Radiative corrections to neutrino deep inelastic scattering are revisited. One-loop electroweak corrections are re-calculated within the automatic SANC system. Terms with mass singularities are treated including higher order leading logarithmic corrections. Scheme dependence of corrections due to weak interactions is investigated. The results are implemented into the data analysis of the NOMAD experiment. The present theoretical accuracy in description of the process is discussed
Effects due to spectator interaction in deep inelastic processes
International Nuclear Information System (INIS)
Smilga, A.V.
1979-01-01
The simplest diagrams describing interaction with the spectator in the e - π→e - + hadrons deep inelastic process are considered. The contribution of the final state interaction diagram to the structure function considerable in the Feynman gauge is suppressed under the temporal gauge choice in accordance with the results of the naive parton model. The expressin for the cross section of the process when large quark momentum is transferred to the spectator is derived
Target mass effects in polarized deep-inelastic scattering
International Nuclear Information System (INIS)
Piccione, A.
1998-01-01
We present a computation of nucleon mass corrections to nucleon structure functions for polarized deep-inelastic scattering. We perform a fit to existing data including mass corrections at first order in m 2 /Q 2 and we study the effect of these corrections on physically interesting quantities. We conclude that mass corrections are generally small, and compatible with current estimates of higher twist uncertainties, when available. (orig.)
Computer Program for Inelastic Neutron Scattering by an Anharmonic Crystal
International Nuclear Information System (INIS)
Bohlin, L.; Ebbsjoe, I.; Hoegberg, T.
1969-02-01
A description is given of the program SAW (Shift and Width), which calculates the energy-dependent shift and width of the intensity peaks obtained for thermal neutrons scattered inelastically by an anharmonic crystal. The program has been coded in FORTRAN IV and may be applied to every solid with a monatomic face-centered cubic lattice where the intermolecular interactions can be described by a centro-symmetrical potential. Interactions beyond third neighbours are neglected
Non-Markovian features of deeply inelastic collisions
International Nuclear Information System (INIS)
Pal, D.; Chattopadhyay, S.; Kar, K.
1988-01-01
To study the effect of memory in the diffusion processes (of charge, mass etc) observed in deeply inelastic heavy-ion reactions, we derive non-Markovian transport equations for the exponential and Gaussian memory kernels. The centroid and the variance of the distribution are expressed in terms of the memory time, drift and diffusion coefficients. The predictions based on this theory show better agreement with the experimental data than the Markovian results. (author)
Simulation of a complete inelastic neutron scattering experiment
DEFF Research Database (Denmark)
Edwards, H.; Lefmann, K.; Lake, B.
2002-01-01
A simulation of an inelastic neutron scattering experiment on the high-temperature superconductor La2-xSrxCuO4 is presented. The complete experiment, including sample, is simulated using an interface between the experiment control program and the simulation software package (McStas) and is compared...... with the experimental data. Simulating the entire experiment is an attractive alternative to the usual method of convoluting the model cross section with the resolution function, especially if the resolution function is nontrivial....
Amplitude correlations for inelastic proton scattering from 48Ti
International Nuclear Information System (INIS)
Chou, B.H.; Mitchell, G.E.; Bilpuch, E.G.; Westerfeldt, C.R.
1981-01-01
The magnitudes and relative signs of inelastic proton channel amplitudes were determined for three decay channels for 45 5/2 + resonances in 49 V. The reduced widths in each channel follow a Porter-Thomas distribution, but extremely large amplitude correlations are observed - for one pair of channel amplitudes the relative sign is positive for 43 of 45 resonances. These results provide the first direct test of the Krieger-Porter reduced width amplitude distribution. (orig.)
Quark antisymmetrization and deep-inelastic scattering. Pt. 2
International Nuclear Information System (INIS)
Meyer, H.; Mulders, P.J.; Spit, W.F.M.
1994-01-01
We consider the effects of quark antisymmetrization for nuclear structure functions. Antisymmetrizing the naive folding of nuclear wave functions in terms of nucleons and the nucleon wave function in terms of quarks, introduces additional contributions. Using the calculated results on quark three-momentum distributions, we calculate the effects on the deep-inelastic structure functions for s- and p-wave nuclei. The effects of quark antisymmetrization turn out to be small. (orig.)
Computer Program for Inelastic Neutron Scattering by an Anharmonic Crystal
Energy Technology Data Exchange (ETDEWEB)
Bohlin, L; Ebbsjoe, I; Hoegberg, T
1969-02-15
A description is given of the program SAW (Shift and Width), which calculates the energy-dependent shift and width of the intensity peaks obtained for thermal neutrons scattered inelastically by an anharmonic crystal. The program has been coded in FORTRAN IV and may be applied to every solid with a monatomic face-centered cubic lattice where the intermolecular interactions can be described by a centro-symmetrical potential. Interactions beyond third neighbours are neglected.
Future Deep Inelastic Scattering with the LHeC
Klein, Max
2018-01-01
For nearly a decade, Guido Altarelli accompanied the Large Hadron electron Collider project, as invited speaker, referee and member of the International Advisory Committee. This text summarises the status and prospects of the development of the LHeC, with admiration for a one-time scientist and singular leader whom I met first nearly 40 years ago under the sun shining for the "Herceg Novi School" in Kupari, where we both lectured about the beautiful science of Deep Inelastic Scattering and en...
Long-range correlations in deep-inelastic scattering
International Nuclear Information System (INIS)
Chekanov, S.V.
1999-01-01
Multiplicity correlations between the current and target regions of the Breit frame in deep-inelastic scattering processes are studied. It is shown that the correlations are sensitive to the first-order perturbative QCD effects and can be used to extract the behaviour of the boson-gluon fusion rates as a function of the Bjorken variable. The behaviour of the correlations is derived analytically and analyzed using a Monte Carlo simulation. (author)
Forward jet production in deep inelastic scattering at HERA
Czech Academy of Sciences Publication Activity Database
Aktas, A.; Andreev, V.; Anthonis, A.; Cvach, Jaroslav; Reimer, Petr; Sedlák, Jaroslav; Zálešák, Jaroslav
2006-01-01
Roč. 46, - (2006), s. 27-42 ISSN 1434-6044 R&D Projects: GA MŠk(CZ) LC527; GA MŠk(CZ) 1P05LA259 Institutional research plan: CEZ:AV0Z10100502 Keywords : HI experiment * ep scattering * deep inelastic * cross section * quantum chromodynamics Subject RIV: BF - Elementary Particles and High Energy Physics Impact factor: 3.251, year: 2006
Inclusive quasielastic and deep inelastic electron scattering at high energies
International Nuclear Information System (INIS)
Day, D.B.
1990-01-01
With high electron energies a kinematic regime can be reached where it will be possible to separate quasielastic and deep inelastic scattering. We present a short description of these processes which dominate the inclusive spectrum. Using the highest momentum transfer data available to guide our estimates, we give the kinematic requirements and the cross sections expected. These results indicate that inclusive scattering at high q has a yet unfilled potential. 18 refs., 13 figs
Inelastic neutron spectra and cross sections for 238 U
International Nuclear Information System (INIS)
Kornilov, N.V.; Kagalenko, A.V.
1994-01-01
The report discusses the experimental facilities of IPPE, results of spectra and cross sections investigations. The problems of existing data libraries were highlighted. Some of these problems for example, inelastic spectra at high energy may be solved by correct theoretical calculation. Others like level cross sections at E > 2 MeV and the possible structure of excitation function for group levels between 0.5 to 0.85 MeV demand new experimental efforts. 21 refs., 11 figs., 5 tabs
Inelastic scattering of neutrons by spin waves in terbium
DEFF Research Database (Denmark)
Bjerrum Møller, Hans; Houmann, Jens Christian Gylden
1966-01-01
Measurements of spin-wave dispersion relations for magnons propagating in symmetry directions in ferromagnetic Tb; it is first experiment to give detailed information on magnetic excitations in heavy rare earths; Tb was chosen for these measurements because it is one of few rare-earth metals which...... does not have very high thermal-neutron capture cross section, so that inelastic neutron scattering experiments can give satisfactory information on magnon dispersion relations....
On the radiative corrections to the neutrino deep inelastic scattering
International Nuclear Information System (INIS)
Bardin, D.Yu.; Dokuchaeva, V.A.
1986-01-01
A unique set of formulae is presented for the radiative corrections to the double differential cross section of deep inelastic neutrino scattering in channels of charged and neutral currents within a simple quark parton model in a renormalization scheme on mass-shell. It is shown that these cross sections when being integrated up to the one-dimensional distribution or up to the total cross section reproduce many results existing in the literature
Implications of new deep inelastic scattering data for parton distributions
International Nuclear Information System (INIS)
Martin, A.D.; Stirling, W.J.; Roberts, R.G.
1988-01-01
We perform a next-to-leading order structure function F 2 analysis of μN and νN deep inelastic data in an attempt to resolve the disagreement between recent EMC (European muon collaboration effect) and BCDMS measurements of F 2 for μp scattering. Equally acceptable QCD fits are obtained including either set of μN data, but a comparison with Drell-Yan data appears to favour the parton distributions derived from the BCDMS data. (author)
Hadronic final states and sum rules in deep inelastic processes
International Nuclear Information System (INIS)
Pal, B.K.
1977-01-01
In order to get maximum information on the hadronic final states and sum rules in deep inelastic processes, Regge phenomenology and quarks parton model have been used. The unified picture for the production of hadrons of type i as a function of Bjorken and Feyman variables with only one adjustable parameter is formulated. The results of neutrino experiments and the production of charm particles are discussed in sum rules. (author)
On deformed tensor potential for inelastic deuteron scattering
International Nuclear Information System (INIS)
Raynal, Jacques.
1980-08-01
Tensor analysing powers for inelastic deuteron scattering have been measured around 12 to 15 MeV. There is no problem to use such a tensor potential for the excited states in coupled channel calculations. However, for transition potentials, form factors are very different. A fit has been done with the first order vibrational model for 64 Ni(d,d') 64 Ni*, 2 + at 1,344 MeV
Uncertainty in the inelastic resonant scattering assisted by phonons
International Nuclear Information System (INIS)
Garcia, N.; Garcia-Sanz, J.; Solana, J.
1977-01-01
We have analyzed the inelastic minima observed in new results of He atoms scattered from LiF(001) surfaces. This is done considering bound state resonance processes assisted by phonons. The analysis presents large uncertainties. In the range of uncertainty, we find two ''possible'' bands associated with the vibrations of F - and Li + , respectively. Many more experimental data are necessary to confirm the existence of these processes
Inelastic scattering using the three-axis spectrometer technique
International Nuclear Information System (INIS)
Currat, R.
1999-01-01
The three-axis technique is a basic neutron scattering technique for inelastic work on single-crystal specimens. There is, at the moment, a fair degree of complementarity between TAS instruments on steady-state sources and TOF instruments on steady-state or pulsed sources. The technique is described, the issue of TAS versus TOF method is discussed, and investigations relating to the resolution functions are presented. (K.A.)
Inelastic scattering at the B K edge of hexagonal BN
Energy Technology Data Exchange (ETDEWEB)
Jia, J.J.; Callcott, T.A.; Zhou, L. [Univ. of Tennessee, Knoxville, TN (United States)] [and others
1997-04-01
Many recent soft x-ray fluorescence (SXF) studies have shown that inelastic scattering processes make important contributions to the observed spectra for excitation near the x-ray threshold. These effects are all attributed to a process, usually called an electronic Raman scattering (ERS) process, in which energy is lost to an electronic excitation. The theory has been described using second order perturbation theory by Tulkki and Aberg. In different materials, the detailed nature of the electronic excitation producing the energy loss may be very different. In crystalline Si, diamond and graphite, changes in spectral shape and dispersion of spectral features with variation of the excitation energy are observed, which are attributed to k conservation between the photoelectron generated in the excitation process and the valence hole remaining after the coupled emission process. Hence the process is strongly localized in k-space. In haxagonal boron nitride, which has a lattice and band structure very similar to graphite, inelastic scattering produces very different effects on the observed spectra. Here, the inelastic losses are coupled to a strong resonant elastic scattering process, in which the intermediate state is a localized core exciton and the final state is a localized valence exciton, so that the electronic excitation is strongly localized in real rather than reciprocal space.
Inelastic pion scattering by 13C at low energies
International Nuclear Information System (INIS)
Mitchell, J.H.
1987-03-01
Angular distributions for inelastically scattered pions were obtained for several states in 13 C at an incident energy of 65 MeV. The data include results from both π + and π - measurements. In addition, π - measurements were made at T/sub π/ = 50 MeV at one angle to give a two point fixed-q excitation function. The data are compared to theory and the data of others. As might be expected, medium corrections are shown to be considerably more important at low energies than at resonance. This is true for inelastic transitions of multipolarity 0,2 and 3. Parameters derived from an analysis of elastic pion scattering and SCX data also provide an adequate description of the inelastic transitions. The charge asymmetry in the cross sections for the 9/2 + state that was seen at resonance persists at these energies. This result is consistent with an impulse approximation treatment of the spin-flip amplitude. This is true even though the incoming energy of the pions is far below the range where the validity of an impulse treatment is expected. 65 refs., 45 figs
Inelastic neutron scattering method in hard coal quality monitoring
International Nuclear Information System (INIS)
Cywicka-Jakiel, T.; Loskiewicz, J.; Tracz, G.
1994-07-01
Nuclear methods in mining industry and power generation plants are nowadays very important especially because of the need for optimization of combustion processes and reduction of environmental pollution. On-line analysis of coal quality not only economic benefits but contribute to environmental protection too. Neutron methods especially inelastic scattering and PGNAA are very useful for analysis of coal quality where calorific valve, ash and moisture content are the most important. Using Pu-Be or Am-Be isotopic sources and measuring carbon 4.43 MeV γ-rays from neutron inelastic scattering: 12 C(n,n'γ) 12 C we can evaluate calorific valve in hard coals with precision better than in PGNAA method. This is mainly because of large cross-section for inelastic scattering and the strong correlation between carbon content and calorific value shown in the paper for different coal basins. The influence of moisture on 4.43 MeV carbon γ-rays in considered in the paper in theoretical and experimental aspects and appropriate formula is introduced. Also the possibilities of determine ash, moisture, Cl, Na and Si in coal are shown. (author). 11 refs, 15 figs
Inelastic neutron scattering method in hard coal quality monitoring
Energy Technology Data Exchange (ETDEWEB)
Cywicka-Jakiel, T.; Loskiewicz, J.; Tracz, G. [Institute of Nuclear Physics, Cracow (Poland)
1994-07-01
Nuclear methods in mining industry and power generation plants are nowadays very important especially because of the need for optimization of combustion processes and reduction of environmental pollution. On-line analysis of coal quality not only economic benefits but contribute to environmental protection too. Neutron methods especially inelastic scattering and PGNAA are very useful for analysis of coal quality where calorific valve, ash and moisture content are the most important. Using Pu-Be or Am-Be isotopic sources and measuring carbon 4.43 MeV {gamma}-rays from neutron inelastic scattering: {sup 12}C(n,n`{gamma}){sup 12}C we can evaluate calorific valve in hard coals with precision better than in PGNAA method. This is mainly because of large cross-section for inelastic scattering and the strong correlation between carbon content and calorific value shown in the paper for different coal basins. The influence of moisture on 4.43 MeV carbon {gamma}-rays in considered in the paper in theoretical and experimental aspects and appropriate formula is introduced. Also the possibilities of determine ash, moisture, Cl, Na and Si in coal are shown. (author). 11 refs, 15 figs.
Measurement of proton inelastic scattering cross sections on fluorine
Energy Technology Data Exchange (ETDEWEB)
Chiari, M., E-mail: chiari@fi.infn.it [Department of Physics and Astronomy, University of Florence and INFN Florence, Sesto Fiorentino (Italy); Caciolli, A. [Department of Physics and Astronomy, University of Padua and INFN Padua, Padova (Italy); Calzolai, G. [Department of Physics and Astronomy, University of Florence and INFN Florence, Sesto Fiorentino (Italy); Climent-Font, A. [CMAM, Universidad Autonoma de Madrid, Madrid (Spain); Lucarelli, F.; Nava, S. [Department of Physics and Astronomy, University of Florence and INFN Florence, Sesto Fiorentino (Italy)
2016-10-01
Differential cross-sections for proton inelastic scattering on fluorine, {sup 19}F(p,p’){sup 19}F, from the first five excited levels of {sup 19}F at 110, 197, 1346, 1459 and 1554 keV were measured for beam energies from 3 to 7 MeV at a scattering angle of 150° using a LiF thin target (50 μg/cm{sup 2}) evaporated on a self-supporting C thin film (30 μg/cm{sup 2}). Absolute differential cross-sections were calculated with a method not dependent on the absolute values of collected beam charge and detector solid angle. The validity of the measured inelastic scattering cross sections was then tested by successfully reproducing EBS spectra collected from a thick Teflon (CF{sub 2}) target. As a practical application of these measured inelastic scattering cross sections in elastic backscattering spectroscopy (EBS), the feasibility of quantitative light element (C, N and O) analysis in aerosol particulate matter samples collected on Teflon by EBS measurements and spectra simulation is demonstrated.
The interpretation of polycrystalline coherent inelastic neutron scattering from aluminium
Roach, Daniel L.; Ross, D. Keith; Gale, Julian D.; Taylor, Jon W.
2013-01-01
A new approach to the interpretation and analysis of coherent inelastic neutron scattering from polycrystals (poly-CINS) is presented. This article describes a simulation of the one-phonon coherent inelastic scattering from a lattice model of an arbitrary crystal system. The one-phonon component is characterized by sharp features, determined, for example, by boundaries of the (Q, ω) regions where one-phonon scattering is allowed. These features may be identified with the same features apparent in the measured total coherent inelastic cross section, the other components of which (multiphonon or multiple scattering) show no sharp features. The parameters of the model can then be relaxed to improve the fit between model and experiment. This method is of particular interest where no single crystals are available. To test the approach, the poly-CINS has been measured for polycrystalline aluminium using the MARI spectrometer (ISIS), because both lattice dynamical models and measured dispersion curves are available for this material. The models used include a simple Lennard-Jones model fitted to the elastic constants of this material plus a number of embedded atom method force fields. The agreement obtained suggests that the method demonstrated should be effective in developing models for other materials where single-crystal dispersion curves are not available. PMID:24282332
Inelastic neutron scattering from synthetic and biological polymers
International Nuclear Information System (INIS)
White, J.W.
1976-01-01
Neutron elastic and inelastic scattering measurements have provided many unique insights into structure, and by reviewing progress on synthetics, important differences likely to arise in biological systems are identified and a direction for studies of the latter is suggested. By neutron inelastic scattering it is possible to measure the frequency of thermally excited interatomic and intermolecular vibrations in crystals. With perfect organic and inorganic crystals the technique is now classical and has given great insight into the crystal forces responsible for the observed structures as well as the phase transitions they undergo. The study of polymer crystals immediately presents two problems of disorder: (1) Macroscopic disorder arises because the sample is a mixture of amorphous and crystalline fractions, and it may be acute enough to inhibit growth of a single crystal large enough for neutron studies. (2) Microscopic disorder in the packing of polymer chains in the ''crystalline'' regions is indicated by broadening of Bragg peaks. Both types of disorder problem arise in biological systems. The methods by which they were partially overcome to allow neutron measurements with synthetic polymers are described but first a classical example of the determination of interatomic forces by inelastic neutron scattering is given
Study of inelastic decay of amplitudes in 49V
International Nuclear Information System (INIS)
Chou, B.H.
1980-01-01
Inelastic decay amplitudes from d-wave resonances in 49 V were obtained for 80 resonances in the proton energy range 2.2 to 3.1 MeV. With the 3 MV Van de Graaff accelerator and high resolution system at the Triangle Universities Nuclear Laboratory, an overall resolution of 350 eV was obtained. The experiment consisted of measurements of the angular distributions of the inelastically scattered protons and the subsequent deexcitation gamma rays. Forty five resonances were assigned J/sup π/ = 5/2 + , while thirty five resonances were assigned 3/2 + . The magnitudes of three inelastic decay amplitudes and the relative signs between these three amplitudes were determined. Large amplitude correlations were observed; the data are in the striking disagreement with the extreme statistical model. The present results provide the first explicit test of the multivariate reduced width amplitude distribution of Krieger and Porter; the agreement is excellent. The physical origin of these channel correlations has not yet been explained
Endochronic theory for inelasticity and failure analysis of concrete structures
Energy Technology Data Exchange (ETDEWEB)
Bazant, Z.P.; Bhat, P.D.; Shieh, C.L.
1976-12-01
A gradual accumulation of inelastic strain can be most conveniently described in terms of the so-called intrinsic time, whose increment depends on the time increment as well as the strain increments. This approach, which gives a particularly simple description of irreversibility of strain at unloading and cyclic loading, was previously developed for metals and is extended herein to concrete by introducing the hydrostatic pressure sensitivity of inelastic strain, the inelastic dilatancy produced by deviator strains, and the strain-softening tendency at high stress. Failure envelopes are obtained as a collection of the peaks of stress-strain diagrams. By comparison with experimental data from the literature, it is demonstrated that the proposed model predicts quite closely: stress-strain diagrams for concretes of different strength; uniaxial, biaxial and triaxial stress-strain diagrams and failure envelopes; failure envelopes for combined torsion and compression, lateral strains and volume expansion in uniaxial and biaxial tests; the behavior of spirally confined concrete; hysteresis loops or repeated high compression; cyclic creep up to 10/sup 6/ cycles; the strain rate effect; the decrease of long time strength; and the increase of short-time strength due to low stress creep.
Endochronic theory for inelasticity and failure analysis of concrete structures
International Nuclear Information System (INIS)
Bazant, Z.P.; Bhat, P.D.; Shieh, C.L.
1976-12-01
A gradual accumulation of inelastic strain can be most conveniently described in terms of the so-called intrinsic time, whose increment depends on the time increment as well as the strain increments. This approach, which gives a particularly simple description of irreversibility of strain at unloading and cyclic loading, was previously developed for metals and is extended herein to concrete by introducing the hydrostatic pressure sensitivity of inelastic strain, the inelastic dilatancy produced by deviator strains, and the strain-softening tendency at high stress. Failure envelopes are obtained as a collection of the peaks of stress-strain diagrams. By comparison with experimental data from the literature, it is demonstrated that the proposed model predicts quite closely: stress-strain diagrams for concretes of different strength; uniaxial, biaxial and triaxial stress-strain diagrams and failure envelopes; failure envelopes for combined torsion and compression, lateral strains and volume expansion in uniaxial and biaxial tests; the behavior of spirally confined concrete; hysteresis loops or repeated high compression; cyclic creep up to 10 6 cycles; the strain rate effect; the decrease of long time strength; and the increase of short-time strength due to low stress creep
Nuclear structure of 41Ca from inelastic proton scattering
International Nuclear Information System (INIS)
Vold, P.B.; Cline, D.; Voigt, M.J.A. de
1977-01-01
Angular distributions have been measured for inelastic and elastic scattering of 19 MeV protons on 40 41 Ca. A total of 89 levels were identified below 6.4 MeV in 41 Ca with an energy resolution of 12 keV. Inelastic transition strengths have been extracted using DWBA theory with a vibrational model form factor. These transition strengths correlate well with inelastic α-scattering and electromagnetic values. The quadrupole strengths are interpreted in terms of the coexistence model and imply that the excited-core admixture in the ground states of both 40 Ca and 41 Ca are approximately 5%. The octupole strengths in 41 Ca exhibits features characteristic of the weak coupling of an fsub(7/2) neutron to the lowest 3 - state in 40 Ca. The l = 5 strength exhibits a similar weak-coupling behavior. In both cases the microscopic structure appreciably reduces the transition strength for the highest spin member of the weak-coupling multiplets. (Auth.)
A dynamic elastic and inelastic scattering theory of high-energy electrons
International Nuclear Information System (INIS)
Wang Zhonglin
1990-01-01
A review is given on the applications of elastic multislice theory for simulating the images and diffractions of reflection electron microscopy. The limitation of this theory is illustrated according to some experimental observations. A generalized elastic and inelastic multislice theory is then introduced from quantum mechanics; its applications for approaching inelastic plasmon excitation and phonon excitation (or thermal diffuse scattering) are discussed. The energy-filtered inelastic high resolution images can be simulated based on this theory
Determination of the rate of energy partition in deeply inelastic collisions
International Nuclear Information System (INIS)
Lazzarini, A.; Vandenbosch, R.
1984-01-01
We discuss how excitation energy is partitioned in a deeply inelastic collision. Using the nucleon exchange mechanism for the deep inelastic scattering process, it is possible to draw on existing information about the evolution of the charge and mass distributions with energy loss and combine this with recent information on the partition of excitation energy in deeply inelastic collisions to obtain rates of heating for the two reaction partners
Excitation of the shear horizontal mode in a monolayer by inelastic helium atom scattering
DEFF Research Database (Denmark)
Bruch, L. W.; Hansen, Flemming Yssing
2005-01-01
Inelastic scattering of a low-energy atomic helium beam (HAS) by a physisorbed monolayer is treated in the one-phonon approximation using a time-dependent wave,packet formulation. The calculations show that modes with shear horizontal polarization can be excited near high symmetry azimuths....... The diffraction and inelastic processes arise from a strong coupling of the incident atom to the target and the calculated results show large departures from expectations based on analogies to inelastic thermal neutron scattering....
XXth international workshop on deep-inelastic scattering and related topics. DIS 2012. Proceedings
International Nuclear Information System (INIS)
Brock, Ian C.
2013-03-01
The following topics were dealt with: Structure functions, diffraction and vector mesons, electroweak interactions, hadronic final states, heavy flavours, spin physics, future of deep inelastic scattering. (HSI)
XXth international workshop on deep-inelastic scattering and related topics. DIS 2012. Proceedings
Energy Technology Data Exchange (ETDEWEB)
Brock, Ian C. [ed.
2013-03-15
The following topics were dealt with: Structure functions, diffraction and vector mesons, electroweak interactions, hadronic final states, heavy flavours, spin physics, future of deep inelastic scattering. (HSI)
International Nuclear Information System (INIS)
Muresan, Cristian; Vaillon, Rodolphe; Menezo, Christophe; Morlot, Rodolphe
2004-01-01
The coupled conductive radiative heat transfer in a two-layer slab with Fresnel interfaces subject to diffuse and obliquely collimated irradiation is solved. The collimated and diffuse components problems are treated separately. The solution for diffuse radiation is obtained by using a composite discrete ordinates method and includes the development of adaptive directional quadratures to overcome the difficulties usually encountered at the interfaces. The complete radiation numerical model is validated against the predictions obtained by using the Monte Carlo method
International Nuclear Information System (INIS)
Idir, M.
1995-02-01
This work concerns the study of a particular type of X-ray focusing optics known as Bragg-Fresnel lenses, formed through ion-etching of multilayered structures. Using the Super-ACO (LURE/Orsay) synchrotron storage ring, we tested several Bragg-Fresnel lenses having either linear or elliptical geometries (producing a line or a point focus, respectively). Diffraction profiles were first obtained for the linear lenses ion-etched on W/Si multilayers of nano-metric period. The experimental results were compared with our theoretical predictions. We next proposed and tested a solution to the problem superposing the different diffraction orders in the focal plane, that of fabricating Bragg-Fresnel lenses with an off-axis configuration, first for the linear and then the elliptical geometry. An experimental application, for an off-axis elliptical lens produced a focused X-ray spot of 5 x 10 microns 2 for the Super-ACO synchrotron source. The same lens also produced a 1/3-size X-ray image of a grid-like object at 1750 eV using the first and third diffraction orders. (author)
Directory of Open Access Journals (Sweden)
Tae-Yong Park
2017-01-01
Full Text Available Cube satellites have a limitation for generating power because of their cubic structure and extremely small size. In addition, the incidence angle between the sun and the solar panels continuously varies owing to the revolution and rotation of the satellite according to the attitude control strategy. This angle is an important parameter for determining the power generation performance of the cube satellite. In this study, we performed an experimental feasibility study that uses a Fresnel lens as a solar-energy collection system for cube satellite applications, so that the power generation efficiency can be enhanced under the worst incidence angle condition between the sun and solar panels by concentrating and redirecting solar energy onto the solar panels with a commercial Fresnel lens. To verify the effectiveness of the proposed system, we conducted a power-measurement test using a solar simulator and Fresnel lenses at various angles to the light source. In addition, we predicted the on-orbit power-generation enhancement achieved by employing the solar-energy collection system with various attitude control strategies.
CHEMICAL APPLICATIONS OF INELASTIC X-RAY SCATTERING
Energy Technology Data Exchange (ETDEWEB)
HAYASHI,H.; UDAGAWA,Y.; GILLET,J.M.; CALIEBE,W.A.; KAO,C.C.
2001-08-01
Inelastic x-ray scattering (IXS), complementary to other more established inelastic scattering probes, such as light scattering, electron scattering, and neutron scattering, is becoming an important experimental technique in the study of elementary excitations in condensed matters. Over the past decade, IXS with total energy resolution of few meV has been achieved, and is being used routinely in the study of phonon dispersions in solids and liquids as well as dynamics in disordered and biological systems. In the study of electronic excitations, IXS with total energy resolution on the order of 100 meV to 1 eV is gaining wider applications also. For example, IXS has been used to study collective excitations of valence electrons, single electron excitations of valence electrons, as well as core electron excitations. In comparison with the alternative scattering techniques mentioned above, IXS has several advantages. First, IXS probes the full momentum transfer range of the dielectric response of the sample, whereas light scattering is limited to very small momentum transfers, and electron scattering suffers the effects of multiple scattering at large momentum transfers. Second, since IXS measures the bulk properties of the sample it is not surface sensitive, therefore it does not require special preparation of the sample. The greater flexibility in sample conditions and environments makes IXS an ideal probe in the study of liquids and samples under extreme temperature, pressure, and magnetic field. Third, the tunability of synchrotron radiation sources enables IXS to exploit element specificity and resonant enhancement of scattering cross sections. Fourth, IXS is unique in the study of dynamics of liquids and amorphous solids because it can probe the particular region of energy-momentum transfer phase space, which is inaccessible to inelastic neutron scattering. On the other hand, the main disadvantages of IXS are the small cross sections and the strong absorption of
Inelastic neutron scattering for materials science and engineering
International Nuclear Information System (INIS)
Shapiro, S.M.
1995-01-01
The neutron is the ideal probe for studying the positions and motions of atoms in condensed matter. The main advantage of the neutron in inelastic scattering results from its heavy mass when compared to other particles which are used to probe materials such as the photon (light, x-rays, or γ-rays) or the electron. The author discusses the application of neutron scattering to study a number of different materials related problems, including, hard magnets, shape memory effects, and hydrogen distribution in metals
Elastic and inelastic pion reactions on few nucleon systems
International Nuclear Information System (INIS)
Lensky, V.
2007-01-01
In the present work, we are studying elastic and inelastic pion reactions on few-body systems within the framework of chiral effective theory. We consider two specific reactions involving pions on few-nucleon systems, namely pion production in nucleon-nucleon collisions, and incoherent pion photoproduction on the deuteron. These two reactions are closely related to the issue of dispersive and absorptive corrections to the pion-deuteron scattering length, which we also consider in our analysis. The incoherent pion photoproduction is also considered as the possible source for a high-precision determination of the neutron-neutron scattering length. (orig.)
Deep inelastic structure functions in the chiral bag model
International Nuclear Information System (INIS)
Sanjose, V.; Vento, V.; Centro Mixto CSIC/Valencia Univ., Valencia
1989-01-01
We calculate the structure functions for deep inelastic scattering on baryons in the cavity approximation to the chiral bag model. The behavior of these structure functions is analyzed in the Bjorken limit. We conclude that scaling is satisfied, but not Regge behavior. A trivial extension as a parton model can be achieved by introducing the structure function for the pion in a convolution picture. In this extended version of the model not only scaling but also Regge behavior is satisfied. Conclusions are drawn from the comparison of our results with experimental data. (orig.)
Deep inelastic structure functions in the chiral bag model
Energy Technology Data Exchange (ETDEWEB)
Sanjose, V. (Valencia Univ. (Spain). Dept. de Didactica de las Ciencias Experimentales); Vento, V. (Valencia Univ. (Spain). Dept. de Fisica Teorica; Centro Mixto CSIC/Valencia Univ., Valencia (Spain). Inst. de Fisica Corpuscular)
1989-10-02
We calculate the structure functions for deep inelastic scattering on baryons in the cavity approximation to the chiral bag model. The behavior of these structure functions is analyzed in the Bjorken limit. We conclude that scaling is satisfied, but not Regge behavior. A trivial extension as a parton model can be achieved by introducing the structure function for the pion in a convolution picture. In this extended version of the model not only scaling but also Regge behavior is satisfied. Conclusions are drawn from the comparison of our results with experimental data. (orig.).
Higher twist contributions to deep-inelastic structure functions
International Nuclear Information System (INIS)
Bluemlein, J.; Boettcher, H.
2008-07-01
We report on a recent extraction of the higher twist contributions to the deep inelastic structure functions F ep,ed 2 (x,Q 2 ) in the large x region. It is shown that the size of the extracted higher twist contributions is strongly correlated with the higher order corrections applied to the leading twist part. A gradual lowering of the higher twist contributions going from NLO to N 4 LO is observed, where in the latter case only the leading large x terms were considered. (orig.)
Inelastic excitation of sup 1 sup 8 sup 7 Re
Shizuma, T; Oshima, M; Matsuda, M; Hayakawa, T; Koizumi, M; Osa, A; Sugawara, M; Zhang, Y H; Liu, Z
2003-01-01
Excited states in sup 1 sup 8 sup 7 Re populated by inelastic scattering of a 500 MeV sup 8 sup 2 Se beam have been studied by means of in-beam gamma-ray spectroscopy. Levels built on the 5/2 sup + [402] and 9/2 sup - [514] one-quasiparticle states were measured up to I suppi = (21/2 sup +) and (21/2 sup -), respectively. In addition, several new levels including an isomer at 1682 keV with a half-life of 114(23) ns have been found. Quasiparticle configurations of the levels and the transition rates are discussed. (orig.)
Development of inelastic neutron spectrometer (DC-TOF) and utilization
International Nuclear Information System (INIS)
Park, Je Geun; So, J. Y.; Moon, M. K.; Choi, Y. H.; Cho, S. J.; Lee, C. H.; Nam, U. W.; Kim, H. Y.; Kim, H. J.
2010-08-01
DC-TOF is an inelastic neutron spectrometer with potentially very wide applications to areas such as physics, chemistry, biology, and material engineering. And it is the most technically challenging and advanced instrument by using high speed choppers rotating up to 20,000 RPM and wide detector of steradian producing data in the order of a few hundred Mbyte. Through this project, we have successfully developed DC-TOF at KAERI with the development of the following key technologies : - Detector Electronics - Data acquisition software - Data reduction software. We believe that DC-TOF will become a workhorse instrument for the wide community of sciences in Korea
Dirac potentials in a coupled channel approach to inelastic scattering
International Nuclear Information System (INIS)
Mishra, V.K.; Clark, B.C.; Cooper, E.D.; Mercer, R.L.
1990-01-01
It has been shown that there exist transformations that can be used to change the Lorentz transformation character of potentials, which appear in the Dirac equation for elastic scattering. We consider the situation for inelastic scattering described by coupled channel Dirac equations. We examine a two-level problem where both the ground and excited states are assumed to have zero spin. Even in this simple case we have not found an appropriate transformation. However, if the excited state has zero excitation energy it is possible to find a transformation
Charged particle multiplicities in deep inelastic scattering at HERA
International Nuclear Information System (INIS)
Aid, S.; Anderson, M.; Andreev, V.
1996-08-01
Using the H1 detector at HERA, charged particle multiplicity distributions in deep inelastic e + p scattering have been measured over a large kinematical region. The evolution with W and Q 2 of the multiplicity distribution and of the multiplicity moments in pseudorapidity domains of varying size is studied in the current fragmentation region of the hadronic centre-of-mass frame. The results are compared with data from fixed target lepton-nucleon interactions, e + e - annihilations and hadron-hadron collisions as well as with expectations from QCD based parton models. Fits to the negative binomial and lognormal distributions are presented. (orig.)
Thermodynamic approach to the inelastic state variable theories
International Nuclear Information System (INIS)
Dashner, P.A.
1978-06-01
A continuum model is proposed as a theoretical foundation for the inelastic state variable theory of Hart. The model is based on the existence of a free energy function and the assumption that a strained material element recalls two other local configurations which are, in some specified manner, descriptive of prior deformation. A precise formulation of these material hypotheses within the classical thermodynamical framework leads to the recovery of a generalized elastic law and the specification of evolutionary laws for the remembered configurations which are frame invariant and formally valid for finite strains. Moreover, the precise structure of Hart's theory is recovered when strains are assumed to be small
Multiquark states in the deep inelastic muon-nucleus scattering
International Nuclear Information System (INIS)
Titov, A.I.
1983-01-01
The deep-inelastic muon-nucleus scattering in the region forbidden by the kinematics for the scattering on free nucleons, is analysed theoretically. The calculations have been performed under the assumption that the main contribution to the cross section in the considered region of the Bjorken scaling variable, 1 -4 -10 -5 for the nuclear structure function at x approximately equal to 1.4. As it is shown, one has to take into account the six-= ' quark states in extracting the scaling parameter of QCD from the muon-nucleus data at approximately 1
Departures from the impulse approximation in deep inelastic neutron scattering
International Nuclear Information System (INIS)
Mayers, J.
1989-01-01
A new formulation of the impulse approximation (IA) in deep inelastic neutron scattering is developed. It is shown that observed departures from the IA at intermediate momentum transfers are caused by the quantum nature of the initial state rather than final state effects, as has previously been assumed and that these effects become small at high temperatures. It is also argued that final state broadening is significant for He liquids in all feasible experiments, but that in other systems the IA is approached at high momentum transfers. (author)
Magnetic inelastic scattering: Present results and future trends
Energy Technology Data Exchange (ETDEWEB)
Osborn, R.
1996-04-01
Experience over the last 15 years has shsown that pulsed neutron spectrometers are able to contribute to the field of magnetic inelastic scattering. Such spectrometers have high resolution and wide dynamic range, both of which are necessary in order to characterize the magnetic response of the complex systems of current interest, ranging from rare earth-transition metal permanent magnets to quantum critical scatterers. Howevera, all these studies have been constrained by current flux limitations. The development of more powerful spallation neutron sources, such as the JHP, is likely to transform these interesting demonstrations of the potential of pulsed neutron scattering into routine tools for the study of magnetic correlations.
Solution of the transport equation with account for inelastic collisions
International Nuclear Information System (INIS)
Kalashnikov, N.P.; Remizovich, V.S.; Ryazanov, M.I.
1980-01-01
The theory of charged particle scattering in a matter with account for inelastic collisions is considered. In ''directly-forward'' approximation the transport equation at the absence of elastic collisions is obtained. The solution of the transport equation is made without and with account for fluctuation of energy losses. Formulas for path-energy relation are given. Energy spectrum and distribution of fast charged particles with respect to paths are studied. The problem of quantum mechanical approach to the theory of multiple scattering of fast charged particles in a matter is discussed briefly
Inelastic electron tunneling spectroscopy of a single nuclear spin.
Delgado, F; Fernández-Rossier, J
2011-08-12
Detection of a single nuclear spin constitutes an outstanding problem in different fields of physics such as quantum computing or magnetic imaging. Here we show that the energy levels of a single nuclear spin can be measured by means of inelastic electron tunneling spectroscopy (IETS). We consider two different systems, a magnetic adatom probed with scanning tunneling microscopy and a single Bi dopant in a silicon nanotransistor. We find that the hyperfine coupling opens new transport channels which can be resolved at experimentally accessible temperatures. Our simulations evince that IETS yields information about the occupations of the nuclear spin states, paving the way towards transport-detected single nuclear spin resonance.
Vibrationally inelastic electron scattering in a two-channel approximation
Czech Academy of Sciences Publication Activity Database
Čársky, Petr; Čurík, Roman
2008-01-01
Roč. 41, č. 5 (2008), , , 055203-1-6 ISSN 0953-4075 R&D Projects: GA AV ČR IAA100400501; GA AV ČR 1ET400400413; GA AV ČR KJB400400803; GA ČR GA202/08/0631; GA MŠk ME 857 Institutional research plan: CEZ:AV0Z40400503 Keywords : inelastic electron scattering * two-channel approximation Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.089, year: 2008
Probing lumps of wee partons in deep inelastic scattering
International Nuclear Information System (INIS)
Buchmueller, W.
1994-06-01
Recently, the ZEUS collaboration has reported on several remarkable properties of events with a large rapidity gap in deep inelastic scattering. We suggest that the mechanism underlying these events is the scattering of electrons off lumps of wee partons inside the proton. Based on an effective lagrangian approach the Q 2 -, x- and W-distributions are evaluated. For sufficiently small invariant mass of the detected hadronic system, the mechanism implies leading twist behaviour. The x- and W-distributions are determined by the Lipatov exponent which governs the behaviour of parton densities at small x. (orig.)
Development validation and use of computer codes for inelastic analysis
International Nuclear Information System (INIS)
Jobson, D.A.
1983-01-01
A finite element scheme is a system which provides routines so carry out the operations which are common to all finite element programs. The list of items that can be provided as standard by the finite element scheme is surprisingly large and the list provided by the UNCLE finite element scheme is unusually comprehensive. This presentation covers the following: construction of the program, setting up a finite element mesh, generation of coordinates, incorporating boundary and load conditions. Program validation was done by creep calculations performed using CAUSE code. Program use is illustrated by calculating a typical inelastic analysis problem. This includes computer model of the PFR intermediate heat exchanger
Database for 238U inelastic scattering cross section evaluation
International Nuclear Information System (INIS)
Kanda, Yukinori; Fujikawa, Noboru; Kawano, Toshihiko
1993-10-01
There are discrepancies among evaluated neutron inelastic scattering cross sections for 238 U in the evaluated nuclear data files, JENDL-3, ENDF/B-VI, JEF-2, BROND-2 and CENDL-2. Re-evaluating them is internationally being discussed to obtain the best outcome which can be accepted in common at the present by experts in the world. This report has been compiled to review the discrepancies among the evaluations in the present data files and to provide a common database for the re-evaluation work (author)
Charged current deep-inelastic scattering at three loops
International Nuclear Information System (INIS)
Moch, S.; Rogal, M.
2007-04-01
We derive for deep-inelastic neutrino(ν)-proton(P) scattering in the combination νP- anti νP the perturbative QCD corrections to three loops for the charged current structure functions F 2 , F L and F 3 . In leading twist approximation we calculate the first five odd-integer Mellin moments in the case of F 2 and F L and the first five even-integer moments in the case of F 3 . As a new result we obtain the coefficient functions to O(α 3 s ) while the corresponding anomalous dimensions agree with known results in the literature. (orig.)
Heavy ion inelastic scattering with a 4π gamma detector
International Nuclear Information System (INIS)
Gross, E.E.
1989-01-01
Heavy-ion inelastic scattering with a new technique that uses a 4π γ-ray detector in coincidence with charged particle detectors is applied to 24 Mg(200 MeV) + 208 Pb scattering. In addition to differential cross sections, a complete particle-γ angular correlation is obtained for decay of the 2 1 + (1.37 MeV) state of 24 Mg. The data are analyzed in coupled-channels. The correlation data proves to be especially sensitive to the static quadrupole moment. 14 refs., 9 figs
Elastic and inelastic pion reactions on few nucleon systems
Energy Technology Data Exchange (ETDEWEB)
Lensky, V.
2007-09-29
In the present work, we are studying elastic and inelastic pion reactions on few-body systems within the framework of chiral effective theory. We consider two specific reactions involving pions on few-nucleon systems, namely pion production in nucleon-nucleon collisions, and incoherent pion photoproduction on the deuteron. These two reactions are closely related to the issue of dispersive and absorptive corrections to the pion-deuteron scattering length, which we also consider in our analysis. The incoherent pion photoproduction is also considered as the possible source for a high-precision determination of the neutron-neutron scattering length. (orig.)
New results from deep inelastic muon-nucleon scattering
International Nuclear Information System (INIS)
Coignet, G.
1982-01-01
Focusing on the new results gained from deep inelastic muon scatterings, the author details three main topics - the Fz structure function measurements gained from hydrogen, carbon and iron targets, open and hidden charm production, from multimuon events, hardonic production with forward jets and forward protons/antiprotons. He discusses the places of experimentation where these results arose, Berkley - FNAL - Princeton, Bologna,-CERN-DubraMunich-Saclay and the European muon collaboration. Finally, he concludes by reviewing the various results and what might be concluded from them
A compilation of structure functions in deep-inelastic scattering
International Nuclear Information System (INIS)
Roberts, R.G.; Whalley, M.R.
1991-01-01
A compilation of data on the structure functions F 2 , xF 3 , and R = σ L /σ T from lepton deep-inelastic scattering off protons and nuclei is presented. The relevant experiments at CERN, Fermilab and SLAC from 1985 are covered. All the data in this review can be found in and retrieved from the Durham-RAL HEP Databases (HEPDATA on the RAL and CERN VM systems and on DURPDG VAX/VMS) together with data on a wide variety of other reactions. (author)
Multiple production of hadrons in deep-inelastic processes
International Nuclear Information System (INIS)
Kiselev, A.V.; Petrov, V.A.
1984-01-01
A formula to describe an average hadron multiplicity on deep-inelastic processes has been proposed. On the basis of available experimental data predictions are made about the behaviour of average multiplicity at higher energies. The W-dependence of obserVed in experiments at present remains invariable up to energies W approximately 20-25 GeV. At W> or approXimately 25 GeV there will begin a rapid ibcrease of , which is analogous to the increase, observed for sub(esup(+)esup(-)) and is of the same nature
Application of Incoherent Inelastic Neutron Scattering in Pharmaceutical Analysis
DEFF Research Database (Denmark)
Bordallo, Heloisa N.; A. Zakharov, Boris; Boidyreva, E.V.
2012-01-01
This study centers on the use of inelastic neutron scattering as an alternative tool for physical characterization of solid pharmaceutical drugs. On the basis of such approach, relaxation processes in the pharmaceutical compound phenacetin (p-ethoxyacetanilide, C(10)H(13)NO(2)) were evidenced...... contributes to understanding the relationships between intermolecular hydrogen bonds, intramolecular dynamics, and conformational flexibility in pharmaceuticals on a molecular level, which can help in evaluating phase stability with respect to temperature variations on processing or on storage, and is related...
Inclusive and exclusive deep-inelastic electron scattering
International Nuclear Information System (INIS)
Morgenstern, J.
1985-11-01
In this talk, I will present some deep inelastic electron scattering experiments done recently at Saclay with the purpose of studying high momentum components in the nucleus, many body effects as correlations, exchange currents, and the electron-nucleon interaction inside the nuclear medium. For that purpose we have performed (e,e') and (ee'p) experiments. When we detect only the scattered electron, we get some average properties less sensitive to final state interaction; in ee'p measurements we are more specific