Industrial pollution load assessment in Phnom Penh, Cambodia using an industrial pollution projection system.

Science.gov (United States)

San, Vibol; Spoann, Vin; Schmidt, Johannes

2018-02-15

Approximately 56% out of the total 1302 Cambodian firms are operated in the Capital city of Cambodia. The necessary information on industrial pollution to set strategies, priorities and action plans on environmental protection issues is absent in Cambodia. In the absence of this data, effective environmental protection cannot be implemented. The objective of this study is to estimate industrial pollution load by employing the Industrial Pollution Projection System, a rapid environmental management tool for assessment of pollution load, to produce a scientific rational basis for preparing future policy direction to reduce industrial pollution in Phnom Penh city. Factory data between 1994 and 2014 obtained from the Ministry of Industry and Handicraft of Cambodia were used in our study. Due to the high number of employees, the total environmental load generated in Phnom Penh city was estimated to be 476,981Mg in 2014. Phnom Penh city generated 189,109Mg of VOC, 165,411Mg of toxic chemicals to air, 38,523Mg of toxic chemicals to land, and 28,968Mg of SO 2 in 2014. The results of the estimation show that the Textiles and Apparel sector was the highest generators of toxic chemicals into land and air, and toxic metals into land, air and water, while the Basic Metal sector was the greatest contributor of toxic chemicals to water. The Textiles and Apparel sector alone emitted 436,016Mg of total pollution load. The results indicate that the Dangkao and Meanchey districts were the greatest emitters of all pollutants in Phnom Penh. The results suggest that reduction in industrial pollution could be achieved by focusing on the most polluting sectors and areas. Adopting waste minimization strategies, which include cleaner production processes, will not only reduce the cost of controlling pollution, it will also make manufacturing more efficient thereby increasing profits while reducing pollution load in the long run. Copyright © 2017 Elsevier B.V. All rights reserved.

the role of industry in air pollution

International Nuclear Information System (INIS)

Kdeih, Naji

1998-01-01

Industry is among the main sources of air pollution in Lebanon. Industrial plants emits dangerous effluents affecting on human health and on population living in industrial zones. Personnel within industries ignore the dangerous effect of substances they use in their work and the toxic effect of gaseous, liquid and solid wastes produced and their impact on health and on environment. A major attention should be paid by Lebanese government to avoid the increasing of atmospheric pollution and must encourage the monitoring of air pollution and its effect on human target organs in the influenced zones. Within industries air is contaminated by gases, vapor, dusts in high rates. Attention has to be focused to the diseases due to breathing diseases, Asbestos, arterial high blood pressure, stress, digestive diseases and other

Industrial pollutions is an environmental issue of Karachi urban area

International Nuclear Information System (INIS)

Jokhio, M.H.; Abro, M.I.; Essani, A.

2005-01-01

The Industrial pollution is one of the serious Environmental issues of the Karachi urban area, categorized as air pollution and water pollution. The localization more the 6000 industries in Karachi urban area at four different sites of Sindh industrial trading estate, Landhi industrial trading estate, Korangi industrial area west Warf industrials, Port Qasim industrial. Area and Hub industrial are near Karachi city. The major iron and steel industries includes Pakistan steel mills and its allied industries at Bin Qasim more than 100 re-rolling industries are located at site area. Karachi ship yard engineering works, Peoples steel Mill, automobile industries and various manufacturing industries which requires metal and its alloy in manufacturing of product mostly located at Bin Qasim, Korangi, and Shershah site areas. None of the industrial sector contain the waster treatment or recycling plant. The ill planted growth of Karachi and its industries caused the environmental degradation of the city and its coastal areas complete with massive mangrove destruction, air water, fishing, and agriculture possessing a potential threat to the lives of more than 10 million citizens. The environmental issues of the metal related industries include the scrap, waste and pollution. Scrapes am waste of the metal industries can be reused in other manufacturing of engineering materials or recycled to produce the new material. However the pollution is the one of the major environmental issue related with the metal industries which need the considerable research and development work in order to over come the serve environmental issues of the urban areas. This article reviews and identifies the level of industrial pollution emphasized on metal related industries of the Karachi urban areas. (author)

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China

OpenAIRE

Li, Gerui; Lei, Yalin; Ge, Jianping; Wu, Sanmang

2017-01-01

This study uses a vector autoregression (VAR) model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1) because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2) che...

Analysis of nickel industrial wastes by nuclear techniques and its pollution assessment

International Nuclear Information System (INIS)

Diaz Rizo, O.; Coto Hernandez, I.; Lopez Pino, N.; D'Alessandro Rodriguez, K.; Arado Lopez, J.O.; Diaz Arado, O.; Reyes Perez, H.

2011-01-01

The concentration of some heavy metal (Mn, Fe, Co, Ni, Cu and Zn) in nickel industrial wastes from Moa, northeastern Cuba, is determined. The analysis was performed by External Standard method of ED-XRF, using 238 Pu (1.11 GBq) excitation source and laterite certified reference material as standards. The capability of INAA using neutrons from a Pu-Be (10 7 n/s) source and Low-Background Gamma Spectrometer (LBGS) at InSTEC is studied. The determined concentration values for Ni, Co, Cu and Zn shows a different pollution degree according to Dutch regulations and US NOAA guidelines. (Author)

Pollution prevention in the petroleum refining industry - bibliography

International Nuclear Information System (INIS)

Fournier, M.

1995-03-01

The Great Lakes Pollution Prevention Centre has compiled a list of references to assist the petroleum refining industry in adopting pollution prevention as an important environmental management strategy. Items included were divided into 14 categories of pollution types, such as air emissions, alternative fuels, chemical substitution, grounds keeping, leaks and spills, paints, waste management plan and others

Waste incineration industry and development policies in China.

Science.gov (United States)

Li, Yun; Zhao, Xingang; Li, Yanbin; Li, Xiaoyu

2015-12-01

The growing pollution from municipal solid waste due to economic growth and urbanization has brought great challenge to China. The main method of waste disposal has gradually changed from landfill to incineration, because of the enormous land occupation by landfills. The paper presents the results of a study of the development status of the upstream and downstream of the waste incineration industry chain in China, reviews the government policies for the waste incineration power industry, and provides a forecast of the development trend of the waste incineration industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

Solid waste management in Khartoum industrial area

International Nuclear Information System (INIS)

Elsidig, N. O. A.

2004-05-01

This study was conducted in Khartoum industrial area (KIA). The study discusses solid waste generation issues in KIA as well as solid waste collection, storage, transport and final disposal methods. A focus on environmental impact resulting from the accumulation of solid waste was presented by reviewing solid waste management in developed as well as developing countries starting from generation to final disposal. Environmental health legislation in Sudan was investigated. The study covers all the (eight) industrial sub-sectors presented in KIA. The main objective of the study is to assess the situation of solid waste in KIA. To fulfill the objectives of the study the researcher deemed it necessary to explore problems related to solid waste generation and solid waste arrangement with special emphasis on final disposal methods. Practically, 31 (thirty-one) factories representing the different industrial sub-sectors in KIA were studied. This represents 25% of the total number of factories located in KIA. Data were obtained by, questionnaires, interviews and observations mainly directed to concerned officials, solid waste workers, pickers and brokers. Obtained data were stored, coded, tabulated and analyzed using the computer systems (excel and SPSS programmes). The obtained results should clear deficiency in the management of solid waste which led to great environmental deterioration in KIA and neighboring residential areas. The environment in studied area is continuously polluted due to high pollution loads and unproved solid waste management. In order to maintain health environment operating factories have to pretreated their solid waste according to the recognized standards and waste minimization techniques such as recycling and re use should be widely applied, moreover, running crash programme for environmental sanitation in Khartoum state should be expanded and improved to include special characteristics of solid waste from industries. Finally, increase awareness

Energy Efficient Removal of Volatile Organic Compounds (VOCs) and Organic Hazardous Air Pollutants (o-HAPs) from Industrial Waste Streams by Direct Electron Oxidation

Energy Technology Data Exchange (ETDEWEB)

Testoni, A. L.

2011-10-19

This research program investigated and quantified the capability of direct electron beam destruction of volatile organic compounds and organic hazardous air pollutants in model industrial waste streams and calculated the energy savings that would be realized by the widespread adoption of the technology over traditional pollution control methods. Specifically, this research determined the quantity of electron beam dose required to remove 19 of the most important non-halogenated air pollutants from waste streams and constructed a technical and economic model for the implementation of the technology in key industries including petroleum refining, organic & solvent chemical production, food & beverage production, and forest & paper products manufacturing. Energy savings of 75 - 90% and green house gas reductions of 66 - 95% were calculated for the target market segments.

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China.

Science.gov (United States)

Li, Gerui; Lei, Yalin; Ge, Jianping; Wu, Sanmang

2017-03-02

This study uses a vector autoregression (VAR) model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1) because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2) chemical oxygen demand was taken as an indicator of sewage treatment in environmental protection plans; hence, the chemical oxygen demand discharge decreased in all mining industries; (3) tax reduction policies, which are only implemented in coal mining and washing and extraction of petroleum and natural gas, decreased the industrial solid waste discharge in these two mining industries.

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China

Directory of Open Access Journals (Sweden)

Gerui Li

2017-03-01

Full Text Available This study uses a vector autoregression (VAR model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1 because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2 chemical oxygen demand was taken as an indicator of sewage treatment in environmental protection plans; hence, the chemical oxygen demand discharge decreased in all mining industries; (3 tax reduction policies, which are only implemented in coal mining and washing and extraction of petroleum and natural gas, decreased the industrial solid waste discharge in these two mining industries.

Animal and industrial waste anaerobic digestion: USA status report

Energy Technology Data Exchange (ETDEWEB)

Lusk, P.D. [Resource Development Associates, Washington, DC (United States)

1996-01-01

Pollutants from unmanaged animal and bio-based industrial wastes can degrade the environment, and methane emitted from decomposing wastes may contribute to global climate change. One waste management system prevents pollution and converts a disposal problem into a new profit center. Case studies of operating systems indicate that the anaerobic digestion of animal and industrial wastes is a commercially available bioconversion technology with considerable potential for providing profitable coproducts, including a cost-effective renewable fuel. Growth and concentration of the livestock industry create opportunities to properly dispose of the large quantities of manures generated at dairy, swine, and poultry farms. Beyond the farm, extension of the anaerobic digestion process to recover methane has considerable potential for certain classified industries - with a waste stream characterization similar to livestock manures. More than 35 example industries have been identified, and include processors of chemicals, fiber, food, meat, milk, and pharmaceuticals. Some of these industries already recover methane for energy. This status report examines some current opportunities for recovering methane from the anaerobic digestion of animal and industrial wastes in the US. Case studies of operating digesters, including project and maintenance histories, and the operator`s {open_quotes}lessons learned,{close_quotes} are included as a reality check. Factors necessary for successful projects, as well as a list of reasons explaining why some anaerobic digestion projects fail, are provided. The role of management is key; not only must digesters be well engineered and built with high-quality components, they must also be sited at facilities willing to incorporate the uncertainties of a new technology. Anaerobic digestion can provide monetary benefits and mitigate possible pollution problems, thereby sustaining development while maintaining environmental quality.

Industrial ecology: Environmental chemistry and hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Manahan, S.E. [Univ. of Missouri, Columbia, MO (United States). Dept. of Chemistry

1999-01-01

Industrial ecology may be a relatively new concept -- yet it`s already proven instrumental for solving a wide variety of problems involving pollution and hazardous waste, especially where available material resources have been limited. By treating industrial systems in a manner that parallels ecological systems in nature, industrial ecology provides a substantial addition to the technologies of environmental chemistry. Stanley E. Manahan, bestselling author of many environmental chemistry books for Lewis Publishers, now examines Industrial Ecology: Environmental Chemistry and Hazardous Waste. His study of this innovative technology uses an overall framework of industrial ecology to cover hazardous wastes from an environmental chemistry perspective. Chapters one to seven focus on how industrial ecology relates to environmental science and technology, with consideration of the anthrosphere as one of five major environmental spheres. Subsequent chapters deal specifically with hazardous substances and hazardous waste, as they relate to industrial ecology and environmental chemistry.

Reception and treatment facilities for waste oils and oil-polluted waters from marine and industrial activities in Gothenburg, Sweden

International Nuclear Information System (INIS)

Andersson, K.; Lexen, S.I.; Hell, M.

1992-01-01

At the beginning of the 1980s, comprehensive solutions were found to problems associated with the handling of oil-polluted water from marine and industrial sources in the Gothenburg area. The treatment plant in the oil harbour has permission to treat 700,000 m 3 /yr of sludge, ballast, slops and other oil-contaminated waters. Following treatment by chemical flocculation, flotation and dual-media filtration, the treated water must not contain more than 5 ppm of oil. Work to improve treatment results has been carried out from the start, in close co-operation with environmental authorities and with the waste generators themselves. Through increased consciousness, improvements in control, and greater source separation, it will be possible to bring about a significantly lower concentration of pollutants in the incoming waste streams. Recent plans include separate treatment of waste streams containing aromatic compounds and heavily polluted waters. Complementary treatment methods, such as activated carbon and air stripping, are under evaluation. (author). 10 figs

Prosperity without pollution: The prevention strategy for industry and consumers

International Nuclear Information System (INIS)

Hirschhorn, J.S.; Oldenburg, K.V.

1990-01-01

Here is the first book to explain why only a preventative environmental strategy can work: because growing population, consumption and industrialization cripple current, rather haphazard, remedial efforts. This book shows how our society can make more with less, be more competitive and less polluting, while maintaining our standard of living by reducing and eventually eliminating the production of wastes and pollutants from industry, commerce, homes, farms, and institutions. This may seem far-fetched, but be prepared to discover in this book that there can be a middle ground between ecology and economy - and that you can help achieve it. You'll find data and examples that any person can use, from engineers in industry to office workers to activists. Every concerned citizen will also want to consider the authors' innovative suggestions for taxing wastes and using the proceeds to help companies and communities switch to new industrial processes. Also, you should evaluate their proposals to reburies meaningful waste and toxicity information on product labels, to make bans on chemicals and products a more credible and available corrective measure, and to secure permanent, high-level government support for pollution prevention

Wastes and pollution: environmental and health impacts; Dechets et pollution: impact sur l'environnement et la sante

Energy Technology Data Exchange (ETDEWEB)

Ngo, Ch.; Regent, A.

2004-07-01

The global aspects of the wastes and pollution management and their consequences on the environment and the public health, are presented. The greenhouse effect, the animal flour, the pollution from the transports, the industrial activities, the agriculture and the chemical and nuclear wastes are detailed and analyzed. (A.L.B.)

Acoustic barriers obtained from industrial wastes.

Science.gov (United States)

Garcia-Valles, M; Avila, G; Martinez, S; Terradas, R; Nogués, J M

2008-07-01

Acoustic pollution is an environmental problem that is becoming increasingly more important in our society. Likewise, the accumulation of generated waste and the need for waste management are also becoming more and more pressing. In this study we describe a new material--called PROUSO--obtained from industrial wastes. PROUSO has a variety of commercial and engineering, as well as building, applications. The main raw materials used for this environmentally friendly material come from slag from the aluminium recycling process, dust from the marble industry, foundry sands, and recycled expanded polystyrene from recycled packaging. Some natural materials, such as plastic clays, are also used. To obtain PROUSO we used a conventional ceramic process, forming new mineral phases and incorporating polluted elements into the structure. Its physical properties make PROUSO an excellent acoustic and thermal insulation material. It absorbs 95% of the sound in the frequency band of the 500 Hz. Its compressive strength makes it ideal for use in ceramic wall building.

Ovarian cancer mortality and industrial pollution.

Science.gov (United States)

García-Pérez, Javier; Lope, Virginia; López-Abente, Gonzalo; González-Sánchez, Mario; Fernández-Navarro, Pablo

2015-10-01

We investigated whether there might be excess ovarian cancer mortality among women residing near Spanish industries, according to different categories of industrial groups and toxic substances. An ecologic study was designed to examine ovarian cancer mortality at a municipal level (period 1997-2006). Population exposure to pollution was estimated by means of distance from town to facility. Using Poisson regression models, we assessed the relative risk of dying from ovarian cancer in zones around installations, and analyzed the effect of industrial groups and pollutant substances. Excess ovarian cancer mortality was detected in the vicinity of all sectors combined, and, principally, near refineries, fertilizers plants, glass production, paper production, food/beverage sector, waste treatment plants, pharmaceutical industry and ceramic. Insofar as substances were concerned, statistically significant associations were observed for installations releasing metals and polycyclic aromatic chemicals. These results support that residing near industries could be a risk factor for ovarian cancer mortality. Copyright © 2015 Elsevier Ltd. All rights reserved.

Environmental justice implications of industrial hazardous waste generation in India: a national scale analysis

Science.gov (United States)

Basu, Pratyusha; Chakraborty, Jayajit

2016-12-01

While rising air and water pollution have become issues of widespread public concern in India, the relationship between spatial distribution of environmental pollution and social disadvantage has received less attention. This lack of attention becomes particularly relevant in the context of industrial pollution, as India continues to pursue industrial development policies without sufficient regard to its adverse social impacts. This letter examines industrial pollution in India from an environmental justice (EJ) perspective by presenting a national scale study of social inequities in the distribution of industrial hazardous waste generation. Our analysis connects district-level data from the 2009 National Inventory of Hazardous Waste Generating Industries with variables representing urbanization, social disadvantage, and socioeconomic status from the 2011 Census of India. Our results indicate that more urbanized and densely populated districts with a higher proportion of socially and economically disadvantaged residents are significantly more likely to generate hazardous waste. The quantity of hazardous waste generated is significantly higher in more urbanized but sparsely populated districts with a higher proportion of economically disadvantaged households, after accounting for other relevant explanatory factors such as literacy and social disadvantage. These findings underscore the growing need to incorporate EJ considerations in future industrial development and waste management in India.

Ovarian cancer mortality and industrial pollution

International Nuclear Information System (INIS)

García-Pérez, Javier; Lope, Virginia; López-Abente, Gonzalo; González-Sánchez, Mario

2015-01-01

We investigated whether there might be excess ovarian cancer mortality among women residing near Spanish industries, according to different categories of industrial groups and toxic substances. An ecologic study was designed to examine ovarian cancer mortality at a municipal level (period 1997–2006). Population exposure to pollution was estimated by means of distance from town to facility. Using Poisson regression models, we assessed the relative risk of dying from ovarian cancer in zones around installations, and analyzed the effect of industrial groups and pollutant substances. Excess ovarian cancer mortality was detected in the vicinity of all sectors combined, and, principally, near refineries, fertilizers plants, glass production, paper production, food/beverage sector, waste treatment plants, pharmaceutical industry and ceramic. Insofar as substances were concerned, statistically significant associations were observed for installations releasing metals and polycyclic aromatic chemicals. These results support that residing near industries could be a risk factor for ovarian cancer mortality. - Highlights: • We studied excess mortality due to ovarian cancer near Spanish industries. • Integrated nested Laplace approximations were used as a Bayesian inference tool. • We found excess ovarian cancer mortality near all industrial groups as a whole. • Risk also was found in towns near industries releasing carcinogens and metals. • Risk was associated with plants releasing polycyclic aromatic chemicals and POPs. - Our results support that residing in the vicinity of pollutant industries could be a risk factor for ovarian cancer mortality

An overview of environmental pollution status and waste treatment technology used in Pakistan

International Nuclear Information System (INIS)

Javed, T.; Qureshi, R.M.; Ahmad, S.; Sajjad, M.I.; Mashiatullah, A.; Shah, Z.

1998-01-01

There is little pollution consciousness in Pakistan. Rapid growth in population and unplanned disposal of untreated industrial, agricultural and domestic wastes has caused severe pollution problems in air, soil, drinking water and coastal marine water environments. To date, no systematic approach is being used in the domestic and industrial sectors for continuous processing and decontamination of solid, liquid and gaseous wastes prior to disposal. The two large industrial and population centers namely, the cities of Karachi and Islamabad, use small scale wastewater treatment facilities consisting of trickling filters and activated sludge process, respectively. Presently, no accelerator is being used in Pakistan for decontamination of hospital, industrial or domestic wastes. However, the prospects of Radiation Technology for waste treatment are well realized and a 250 keV ion accelerator has been developed at the Pakistan Institute of Nuclear Science and Technology (PINSTECH) for research, development and training purposes. The main emphasis is now to locally design and fabricate user dedicated electron beam machines for radiation curing and decontamination of domestic, industrial and hospital wastes

Methods for waste waters treatment in textile industry

OpenAIRE

Srebrenkoska, Vineta; Zhezhova, Silvana; Risteski, Sanja; Golomeova, Saska

2014-01-01

The processes of production of textiles or wet treatments and finishing processes of textile materials are huge consumers of water with high quality. As a result of these various processes, considerable amounts of polluted water are released. This paper puts emphasis on the problem of environmental protection against waste waters generated by textile industry. The methods of pretreatment or purification of waste waters in the textile industry can be: Primary (screening, sedimentation, homo...

Industrial wastes guide for Alsace; Guide des dechets de l`entreprise Alsace

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This guide is aimed for industrial plant managers and gives comprehensive information on industrial waste management: effects of wastes on the environment (water, air, soil), waste processing limitations in Alsace, new regulations, taxes and incentives concerning waste processing in France, and references of national and regional (Alsace) administration and industrial agencies that are related with pollution abatement and control and waste management. The different types of wastes are reviewed, from papers to toxic solvents, with information given on volumes, processes, operators, processing equipment and equipment distributors

The latent causal chain of industrial water pollution in China.

Science.gov (United States)

Miao, Xin; Tang, Yanhong; Wong, Christina W Y; Zang, Hongyu

2015-01-01

The purpose of this paper is to discover the latent causal chain of industrial water pollution in China and find ways to cure the want on discharge of toxic waste from industries. It draws evidences from the past pollution incidents in China. Through further digging the back interests and relations by analyzing representative cases, extended theory about loophole derivations and causal chain effect is drawn. This theoretical breakthrough reflects deeper causality. Institutional defect instead of human error is confirmed as the deeper reason of frequent outbreaks of water pollution incidents in China. Ways for collaborative environmental governance are proposed. This paper contributes to a better understanding about the deep inducements of industrial water pollution in China, and, is meaningful for ensuring future prevention and mitigation of environmental pollution. It illuminates multiple dimensions for collaborative environmental governance to cure the stubborn problem.

Application of tracer techniques to industrial troubleshooting and environmental pollution control

International Nuclear Information System (INIS)

Easey, J.F.

1994-01-01

The field applications of tracer technology are reviewed and three specific examples each are given for use of the technology for industrial troubleshooting and for environmental pollution control. Each example examines the background, the experimental details and the result, particularly with regard to the cost benefits. Specific areas covered are: leak studies in a chemical reactor; wear studies in jet aircraft fuel pump, mass balance studies in gold refining; ocean dispersion of iron rich wastes; pollution discharges of mine waste water; and flow patterns and retention times in waste waster treatment lagoons. (author). 18 refs

The nuclear industry - pollution and risks

International Nuclear Information System (INIS)

Fremlin, J.H.

1985-01-01

Unlike other power sources, the only pollution from the nuclear industry is radioactive pollution, which on average in Britain represents 0.2% of the annual dose due to natural background radiation. This 0.2% is not spread uniformly over the population and there is genuine concern about its effects where it is most concentrated. The only significant doses of radiation to the general public due to the nuclear industry are derived from the spent-fuel reprocessing plant at Sellafield, and in particular from the concentration of Caesium-134 and Caesium-137 in fish, Ruthenium-106 in edible seaweeds and plutonium in shellfish and in silt. The concern about the possible escape of high-level wastes stored at the Sellafield site is discussed, and the hazard compared with that dangerous chemicals stored at other industrial sites. The effects of pollution by the nuclear industry, based on the conventional and generally accepted view of radiation risks, add up to a few deaths per year in the 50 million population of England and Wales from an industry producing 15% of the electricity needs of those countries. When this is compared with the risk associated with other methods of electricity production, the author concludes that replacement by nuclear power of any major source of power using fossil fuel, with the possible exception of natural gas, would save lives

E-Alerts: Environmental pollution and control (water pollution and control). E-mail newsletter

International Nuclear Information System (INIS)

1999-01-01

Topics of discussion include the following: Pollution by municipal wastes, agricultural wastes, industrial wastes, mine wastes, radioactive contaminants; Chemistry and analysis of pollutants; Thermal pollution; Oil pollution; Control techniques and equipment; Sewage treatment; Industrial waste water pretreatment; Hydrology and limnology; Biological and ecological effects; Waste water reuse; Laws, legislation, and regulations; Public administration; Economics; Land use

E-Alerts: Environmental pollution and control (water pollution and control). E-mail newsletter

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-04-01

Topics of discussion include the following: Pollution by municipal wastes, agricultural wastes, industrial wastes, mine wastes, radioactive contaminants; Chemistry and analysis of pollutants; Thermal pollution; Oil pollution; Control techniques and equipment; Sewage treatment; Industrial waste water pretreatment; Hydrology and limnology; Biological and ecological effects; Waste water reuse; Laws, legislation, and regulations; Public administration; Economics; Land use.

Federal legislative and regulatory incentives and disincentives for industrial waste reduction

International Nuclear Information System (INIS)

Cordes, R.; Nixon, J.

1991-10-01

The Office of Industrial Technologies (OIT) within the US DOE has recently initiated the Industrial Waste Reduction Program, which is designed to reduce industrial energy use and pollution by reducing the amount of waste materials generated. The Program's primary focus is to develop and commercialize waste reduction technologies and practices in conjunction with industrial partners. OIT recognizes that adoption of these technologies is often inhibited by an assortment of institutional barriers that are unrelated to technical or economic performance. Therefore, OIT is examining selected barriers to industrial waste reduction to help identify and remove impediments to wider technology implementation. This report examines the incentives and disincentives to industrial waste reduction that are provided in an assortment of legislation and regulations. The intent is to shed light on how our environmental laws affect industry's implementation of waste reduction, what particular problems exist with current legislation/regulations, and what general options are available for correcting any deficiencies. Our study was confined strictly to federal legislation and regulations. During the course of the study, (March and May 1991), we examined 16 pieces of existing legislation and their attendant regulations plus 22 pieces of proposed legislation. In addition, the authors consulted representatives from industry and from the government agencies administering or sponsoring the legislation. The Resource Conservation and Recovery Act (RCRA) is by far the most comprehensive and dominant piece of legislation affecting solid waste disposal. This is because RCRA, which governs, the management of both nonhazardous and hazardous waste, places the most restrictive requirements on industry. Other important pieces of legislation that exert a direct influence on waste reduction per se include the Clean Air Act and the Pollution Prevention Act. 90 refs., 12 tabs

Industrial Pollution in Ghana: Some Selected Case Studies of Industries in Tema

International Nuclear Information System (INIS)

Taylor, Nora Priscilla Ama Kuma

1999-09-01

Waste waters from eight selected industries namely Tema Oil Refinery, Tuyee Manufacturing Industries, Cocoa Processing Company, Tema Lube Oil Company Limited, Pioneer Food Cannery Limited, Bridal Trust Paints Company Limited, Ghana Textiles Manufacturing Company and Ghana Textiles Printing Company Limited were sampled and subjected to various physico-chemical and trace metal analysis to determine levels of pollutants, using standard methods of WHO, AO AC and APHA. Generally, the ROD values were found to be high for all the industries. Some other parameter levels were significantly high enough for the individual industries to deserve attention. Generally, the results seem to suggest that these industries sited in Tema, are likely contributors to the high degree of pollution of the Chemu and Gao Lagoons which have been reported by various workers as being highly polluted. Consequent to the results obtained, an attempt was made to treat the wastewaters. Thus wastewaters of three of these major industries Ghana Textiles Manufacturing Company. Pioneer Food Cannery Company Limited and Tema Lube Oil Company Limited, representing the textile, food and petroleum-based industries in the Tema industrial area of Ghana were subjected to various physical and chemical treatments using mainly local materials, to try and reduce the levels of pollutants detected in the earlier investigations. Sedimentation, filtration using paper and sea-sand and adsorption using charcoals prepared from dried coconut husks and palm kernel husks as well as industrially prepared activated charcoal as adsorbents, were some of the physical methods used whilst chemical precipitation and oxidation-reduction were the chemical methods used to bring about the desired results. Six different naturally occurring soil samples from Ankaful, Ekon and Elmina in the Central Region, Asokwa in the Ashanti Region, Bokazo in the Western Region and Somanya in the Eastern Region were also used to obtain some levels of

Problems of placement of industrial wastes in landfills in the industrial city

Directory of Open Access Journals (Sweden)

STEPANOV Evgeniy Georgievich,

2017-04-01

Full Text Available The article shows that the anthropogenic transformation of the environment increases when production wastes and consumption are placed in landfills. Hygienic condition of the areas with high population density and developed industry is determined by the increased amount of household and industrial waste, mainly deposited in the numerous landfills. This situation is studied on the example of landfills used for industrial wastes produced by the enterprises JSC «Gazprom Neftekhim Salavat», JSC «Salavatsteklo», located in the city of Salavat of the Republic of Bashkortostan. The sources of industrial pollution in Salavat have been analyzed. One should note that the city-forming enterprise is the JSC «Gazprom Neftekhim Salavat» which share of the total amount of wastes generated in the city per year is 80%. Another company which contributes significantly to this process is the JSC «Salavatsteklo». To study the possible migration of contaminants to the aquifer an observation well has been made at the landfill site. The research of the water obtained from the observation well at the polygon identified maximum allowable concentrations for chemical oxygen demand (COD, phenol and oil products. The groundwater occurrence modes have been studied. The migration of the chemicals contained in the body of the landfill, to groundwater, has been revealed. That leads to contamination of surface water. Laboratory studies of water objects in the zone of influence of industrial waste landfill in Romodanovskomu career have been performed. It was determined that excess of maximum permissible concentration of benzene, and the presence of toluene, lead, phenol indicates the pollution of groundwater by substances stored in landfills Romanovskogo career, both by infiltration and subsequent migration to groundwater of adjacent aquifers and through surface runoff and infiltration from snowmelt and rainwater.

Influence of industrial solid waste addition on properties of soil-cement bricks

OpenAIRE

Siqueira, F. B.; Amaral, M. C.; Bou-Issa, R. A.; Holanda, J. N. F.

2016-01-01

Abstract The reuse of pollutant solid wastes produced in distinct industrial activities (avian eggshell waste and welding flux slag waste) as a source of alternative raw material for producing soil-cement bricks for civil construction was investigated. Soil-cement bricks containing up to 30 wt% of industrial solid waste were uniaxially pressed and cured for 28 days. Special emphasis is given on the influence of solid waste addition on the technical properties (as such volumetric shrinkage, wa...

Microbial keratinases: industrial enzymes with waste management potential.

Science.gov (United States)

Verma, Amit; Singh, Hukum; Anwar, Shahbaz; Chattopadhyay, Anirudha; Tiwari, Kapil K; Kaur, Surinder; Dhilon, Gurpreet Singh

2017-06-01

Proteases are ubiquitous enzymes that occur in various biological systems ranging from microorganisms to higher organisms. Microbial proteases are largely utilized in various established industrial processes. Despite their numerous industrial applications, they are not efficient in hydrolysis of recalcitrant, protein-rich keratinous wastes which result in environmental pollution and health hazards. This paved the way for the search of keratinolytic microorganisms having the ability to hydrolyze "hard to degrade" keratinous wastes. This new class of proteases is known as "keratinases". Due to their specificity, keratinases have an advantage over normal proteases and have replaced them in many industrial applications, such as nematicidal agents, nitrogenous fertilizer production from keratinous waste, animal feed and biofuel production. Keratinases have also replaced the normal proteases in the leather industry and detergent additive application due to their better performance. They have also been proved efficient in prion protein degradation. Above all, one of the major hurdles of enzyme industrial applications (cost effective production) can be achieved by using keratinous waste biomass, such as chicken feathers and hairs as fermentation substrate. Use of these low cost waste materials serves dual purposes: to reduce the fermentation cost for enzyme production as well as reducing the environmental waste load. The advent of keratinases has given new direction for waste management with industrial applications giving rise to green technology for sustainable development.

Biological treatment of industrial wastes; Tratamiento biologico de residuos industriales

Energy Technology Data Exchange (ETDEWEB)

Ortiz de Zarate Apodaca, J.M.; Abia Aguila, L

1997-04-01

There are organic elements used in industrial processes which are not able to be recovered. The biological treatment is the alternative for eliminating the organic pollutants from industrial waste water. This technology is being widely accepted because of its low environmental impact. (Author)

Industrial Waste

DEFF Research Database (Denmark)

Christensen, Thomas Højlund

2011-01-01

generation rates and material composition as well as determining factors are discussed in this chapter. Characterizing industrial waste is faced with the problem that often only a part of the waste is handled in the municipal waste system, where information is easily accessible. In addition part...... of the industrial waste may in periods, depending on market opportunities and prices, be traded as secondary rawmaterials. Production-specificwaste from primary production, for example steel slag, is not included in the current presentation. In some countries industries must be approved or licensed and as part...... of the system industry has to inform at the planning stage and afterwards in yearly reports on their waste arising and how the waste is managed. If available such information is very helpful in obtaining information about that specific industry. However, in many countries there is very little information...

Industrial waste heat utilization for low temperature district heating

International Nuclear Information System (INIS)

Fang, Hao; Xia, Jianjun; Zhu, Kan; Su, Yingbo; Jiang, Yi

2013-01-01

Large quantities of low grade waste heat are discharged into the environment, mostly via water evaporation, during industrial processes. Putting this industrial waste heat to productive use can reduce fossil fuel usage as well as CO 2 emissions and water dissipation. The purpose of this paper is to propose a holistic approach to the integrated and efficient utilization of low-grade industrial waste heat. Recovering industrial waste heat for use in district heating (DH) can increase the efficiency of the industrial sector and the DH system, in a cost-efficient way defined by the index of investment vs. carbon reduction (ICR). Furthermore, low temperature DH network greatly benefits the recovery rate of industrial waste heat. Based on data analysis and in-situ investigations, this paper discusses the potential for the implementation of such an approach in northern China, where conventional heat sources for DH are insufficient. The universal design approach to industrial-waste-heat based DH is proposed. Through a demonstration project, this approach is introduced in detail. This study finds three advantages to this approach: (1) improvement of the thermal energy efficiency of industrial factories; (2) more cost-efficient than the traditional heating mode; and (3) CO 2 and pollutant emission reduction as well as water conservation. -- Highlights: •We review situation of industrial waste heat recovery with a global perspective. •We present a way to analyze the potential to utilize industrial waste heat for DH. •Northern China has huge potential for using low-grade industrial waste heat for DH. •A demonstration project is introduced using the universal approach we propose. •It proves huge benefits for factories, heat-supply companies and the society

Renewable energy recovery through selected industrial wastes

Science.gov (United States)

Zhang, Pengchong

Typically, industrial waste treatment costs a large amount of capital, and creates environmental concerns as well. A sound alternative for treating these industrial wastes is anaerobic digestion. This technique reduces environmental pollution, and recovers renewable energy from the organic fraction of those selected industrial wastes, mostly in the form of biogas (methane). By applying anaerobic technique, selected industrial wastes could be converted from cash negative materials into economic energy feed stocks. In this study, three kinds of industrial wastes (paper mill wastes, brown grease, and corn-ethanol thin stillage) were selected, their performance in the anaerobic digestion system was studied and their applicability was investigated as well. A pilot-scale system, including anaerobic section (homogenization, pre-digestion, and anaerobic digestion) and aerobic section (activated sludge) was applied to the selected waste streams. The investigation of selected waste streams was in a gradually progressive order. For paper mill effluents, since those effluents contain a large amount of recalcitrant or toxic compounds, the anaerobic-aerobic system was used to check its treatability, including organic removal efficiency, substrate utilization rate, and methane yield. The results showed the selected effluents were anaerobically treatable. For brown grease, as it is already well known as a treatable substrate, a high rate anaerobic digester were applied to check the economic effect of this substrate, including methane yield and substrate utilization rate. These data from pilot-scale experiment have the potential to be applied to full-scale plant. For thin stillage, anaerobic digestion system has been incorporated to the traditional ethanol making process as a gate-to-gate process. The performance of anaerobic digester was applied to the gate-to-gate life-cycle analysis to estimate the energy saving and industrial cost saving in a typical ethanol plant.

Health state of population as a criterion of harmfulness of environmental pollution with hazardous wastes

International Nuclear Information System (INIS)

Khacatrian, T.S.

1991-01-01

Valuation of children's health state living in an industrial city, in different microdistricts of which environmental pollution with various hazardous wastes takes place, is done. Investigation results established essential distinctions in health state of children's contingent under examination in dependence upon microdistrict of their permanent living in the given city which is connected with the environmental pollution with various hazardous wastes. The received data allow to examine the health state of population as an integral indicator of ecological situation in the region, and also as a criterion of environmental pollution with hazardous wastes. (au)

Spatial distribution of organic pollutants in industrial construction and demolition waste and their mutual interaction on an abandoned pesticide manufacturing plant.

Science.gov (United States)

Huang, Sheng; Zhao, Xin; Sun, Yanqiu; Ma, Jianli; Gao, Xiaofeng; Xie, Tian; Xu, Dongsheng; Yu, Yi; Zhao, Youcai

2016-04-01

A comprehensive field investigation of organic pollutants was examined in industrial construction and demolition waste (ICDW) inside an abandoned pesticide manufacturing plant. Concentrations of eight types of pesticides, a metabolite and two intermediates were studied. The ICDW was under severe and long-term contamination by organophosphorus, intermediates and pyrethroid pesticide with mean concentrations of 23,429, 3538 and 179.4 mg kg(-1), respectively. FT-IR analysis suggested that physical absorption and chemical bonding were their mutual interaction forms. Patterns of total pesticide spatial distribution showed good correlations with manufacturing processes spreading all over the plant both in enclosed workshops and in residues randomly dumped outside, while bricks and coatings were the most vulnerable to pollutants. Ultimately the fate of the OPPs was diversified as the immersion of ICDW in water largely transferred the pollutants into aquatic systems while exposure outside did not largely lead to pesticide degradation. The adoption of centralized collections for the disposal of wastes could only eliminate part of the contaminated ICDW, probably due to lack of knowledge and criteria. Correlation matrix and cluster analysis indicated that regulated disposal and management of polluted ICDW was effective, thus presenting the requirement for its appropriate disposal.

Arsenic in industrial waste water from copper production technological process

OpenAIRE

Biljana Jovanović; Milana Popović

2013-01-01

Investigation of arsenic in industrial waste water is of a great importance for environment. Discharge of untreated waste water from a copper production process results in serious pollution of surface water, which directly affects flora and fauna, as well as humans. There is a need for efficient and environmentally acceptable treament of waste waters containing heavy metals and arsenic. The paper presents an analyisis of the waste water from The Copper Smelter which is discharged into the Bor...

Treatment of Municipal and Industrial Waste by Radiation Processing

International Nuclear Information System (INIS)

Abdelaziz, M.E.

1999-01-01

In recent years the effort in science and technology is shifting from conventional technologies preventing the pollution of air, water and soil, towards processing by gamma or by electron beam (EB) irradiation in order to prevent pollution, rather than curing the problems caused by production processes, which are not optimized with regard to pollution control. Radiation processing may help to improve the environmental situation in two aspects : It provides alternatives to conventional technologies for the cleaning of air, flue gases and water,...etc, and it also helps to realize clean processes for preventing pollution in the first place. This paper will outline the basic principles of radiation processing for waste streams of environmental relevance, will summarize the state-of -the-art in environmental applications of radiation processing to show both the advantages and the limitations of the radiation processing of waste streams, and to highlight the environmental and economic benefits of clean processes made possible by radiation processing applied to municipal and industrial waste. Reference is made to gamma and EB radiation sources, and description of new technologies is presented

Intensifying waste water clarification in heavy and mining industries for sanitation of rivers in the Katowice district

Energy Technology Data Exchange (ETDEWEB)

Paluch, J.; Twardowska, I.

1976-01-01

This article presents a detailed account of the state of water pollution in the main and tributary rivers of the heavily populated and industrialized district of Katowice, Poland: Results of surveys in the years 1969 to 1972 are given. Several tables and maps show the degree of water pollution in rivers, the amount to which the values exceed pollution standards, percentage of treated and untreated industrial waste water entering the rivers, the classification of river sections according to their content of suspensions, phenols and salt. Further figures show the effectiveness of water cleaning flocculating agents and of waste water treatment at coking plants. Black coal mining and processing contributes the greater part to pollution of the rivers. Only 54% of mining industry waste water is cleaned mechanically and 3% chemically. The amount of 3,300 t/d of chlorite and sulfate salts is led into the rivers primarily from the Rybnik coal mining area. The clarification of waste water resulting from hydraulic stowing and from flotation processes is described as most problematic. Research efforts are being made at economic desalination and suspension flocculation. In the coking industry waste water is treated in 88% of the plants, but dephenolization takes place in only 50% of the plants. (29 refs.) (In German)

Removal of Chromium from Waste Water of Tanning Industry Using Bentonite

International Nuclear Information System (INIS)

Abbasi, S.; Wahba, H.; AL-Masri, M.S.

2009-01-01

Tanning industry is considered as one of the oldest industries in the world, which produces solid and liquid wastes, where the Chromium-containing liquid wastes are considered to be as the main liquid pollutant to the environment. In this research, a new method is applied to remove the chromium from the industrial water wastes, which are produced by tanning industry using the Aleppo Bentonite.The experiments on laboratory- prepared samples and collected samples from some tanning factories in Damascus have proved that chromium removal from tanning waste water is very effective for solution of 85-98 %. Moreover, the optimal conditions for the treatment process of tanning waste water by Aleppo Bentonite have determined and found to be (pH=4, Bentonite concentration = 20 g l -1 when chromium concentration is 0.8 g l -1 , solution temperature = 30 degree centigrade, and Bentonite particle size < 90 μm). However, the proposed method can be considered to be an environmental solution for the treatment of tanning industrial wastes in Syria. (author)

Thermal treatments of solid wastes. Different strategies for related pollutant management

Energy Technology Data Exchange (ETDEWEB)

Nicolella, C.; Convertti, A.; Rovatti, M. [Genoa Univ. (Italy); Boschi, R.; Cozzani, V.; Tognotti, L. [Pisa Univ. (Italy). Dept. of Chemistry Engineering

1995-12-31

Thermal treatment of solid wastes present different advantages/disadvantages as far as recovery and emissions concerns. They provide a captive energy source; reduce the quantity of waste to be landfilled; there are limited by-product and pollutant generating problems. Combined treatment of solid wastes (incineration, pyrolysis, gasification) have been considered to evaluate the energy recovery as well as the quality and the amount of pollutants potentially generated by the combined processes. Direct incineration of MSW, RDF or specific industrial wastes represents a viable, definitive, low environmental impact solution for most refuses. Treatment of emissions can be efficiently achieved by dry or wet processes. Nowadays abatement technologies are able to provide emissions within the guidelines of EEC countries. Problems arise when wastes contain large amount of chlorinated compounds (for example PVC) and/or heavy rentals: incineration may be not best way to be pursued. The general aim of the research program carried out by ISTIC (Genova), and Department of Chemical Engineering (Pisa) is to gain fundamental information on pyrolysis of refuse materials and to study the possible industrial application of these processes. Possible solutions have been studied in terms of material and energy balances, in order to verify the feasibility of combined treatments. Here, preliminary results are given on a two-stage process (low temperature pyrolysis (LTP) followed by incineration or gasification/pyrolysis) for treating specific wastes. (author)

Thermal treatments of solid wastes. Different strategies for related pollutant management

Energy Technology Data Exchange (ETDEWEB)

Nicolella, C; Convertti, A; Rovatti, M [Genoa Univ. (Italy); Boschi, R; Cozzani, V; Tognotti, L [Pisa Univ. (Italy). Dept. of Chemistry Engineering

1996-12-31

Thermal treatment of solid wastes present different advantages/disadvantages as far as recovery and emissions concerns. They provide a captive energy source; reduce the quantity of waste to be landfilled; there are limited by-product and pollutant generating problems. Combined treatment of solid wastes (incineration, pyrolysis, gasification) have been considered to evaluate the energy recovery as well as the quality and the amount of pollutants potentially generated by the combined processes. Direct incineration of MSW, RDF or specific industrial wastes represents a viable, definitive, low environmental impact solution for most refuses. Treatment of emissions can be efficiently achieved by dry or wet processes. Nowadays abatement technologies are able to provide emissions within the guidelines of EEC countries. Problems arise when wastes contain large amount of chlorinated compounds (for example PVC) and/or heavy rentals: incineration may be not best way to be pursued. The general aim of the research program carried out by ISTIC (Genova), and Department of Chemical Engineering (Pisa) is to gain fundamental information on pyrolysis of refuse materials and to study the possible industrial application of these processes. Possible solutions have been studied in terms of material and energy balances, in order to verify the feasibility of combined treatments. Here, preliminary results are given on a two-stage process (low temperature pyrolysis (LTP) followed by incineration or gasification/pyrolysis) for treating specific wastes. (author)

Investigation on the efficiency of treated Palm Tree waste for removal of organic pollutants

Science.gov (United States)

Azoulay, Karima; El HajjajiI, Souad; Dahchour, Abdelmalek

2017-04-01

Development of the industrial sector generates several problems of environmental pollution. This issue rises concern among scientific community and decision makers, in this work; we e interested in water resources polluted by the chemical substances, which can cause various problems of health. As an example, dyes generated by different industrial activities such as textile, cosmetic, metal plating, leather, paper and plastic sectors, constitute an important source of pollution. In this work, we aim at investigating the efficiency of palm tree waste for removal of dyes from polluted solution. Our work presents a double environmental aspect, on one hand it constitutes an attempt for valorization of Palm Tree waste, and on the other hand it provides natural adsorbent. The study focuses on the effectiveness of the waste in removing Methylene Bleu and Methyl Orange taken as models of pollutants from aqueous solution. Kinetics and isotherm experiments were conducted in order to determine the sorption behavior of the examined dye. The effects of initial dye and adsorbent concentrations are considered. The results indicate that the correlation coefficient calculated from pseudo-second order equation was higher than the other kinetic equations, indicating that equilibrium data fitted well with pseudo-second order model where adsorption process was chemisorption. The adsorption equilibrium was well described by Langmuir isotherm model.

ASSESSMENT OF TOXICITY OF INDUSTRIAL WASTES USING CROP PLANT ASSAYS

OpenAIRE

Carmen Alice Teacă; Ruxanda Bodîrlău

2008-01-01

Environmental pollution has a harmful action on bioresources, including agricultural crops. It is generated through many industrial activities such as mining, coal burning, chemical technology, cement production, pulp and paper industry, etc. The toxicity of different industrial wastes and heavy metals excess was evaluated using crop plant assays (germination and hydroponics seedlings growth tests). Experimental data regarding the germination process of wheat (from two cultivars) and rye seed...

Environmental technology applications: fact file on toxic contaminants in industrial waste process streams

Energy Technology Data Exchange (ETDEWEB)

Newkirk, H.W.

1977-05-11

This report is a compendium of facts related to chemical materials present in industrial waste process streams which have already been declared or are being evaluated as hazardous under the Toxic Substances Control Act. Since some 400 chemicals are presently covered by consensus standards, the substances reviewed are only those considered to be a major threat to public health and welfare by Federal and State regulatory agencies. For each hazardous material cited, the facts relate, where possible, to an identification of the stationary industrial sources, the kind of waste stream impacted, proposed regulations and established effluent standards, the volume of emissions produced each year, the volume of emissions per unit of industrial product produced, present clean-up capabilities, limitations, and costs. These data should be helpful in providing information for the assessment of potential problems, should be of use to the manufacturers of pollution control equipment or of chemicals for pollution control, should be of use to the operators or potential operators of processes which produce pollutants, and should help to define industry-wide emission practices and magnitudes.

Radiochemical studies on some industrial pollutants released to the environment

International Nuclear Information System (INIS)

Metwally, E.M.Abel-Ghany

1997-01-01

This work aims at characterizing the industrial pollutants that may be released from: Abu-Zaabal fertilizer company, arab ceramic industry, Egyptian alum company near the compass of Atomic Energy Authority (AEA) in Inshas and petroleum pipelines company at the start of lsmailia canal. The work concentrates on soil or/and sediment pollution, the lsmailia canal water stream pollution and plant pollution. Type of the element and its content are major parameters that are traced in the traced in the experimental work. The work stresses on the analysis of the raw materials used in the chosen Factories, their products of current use as well as their wastes and drainage. Instrumental neutron activation analysis (INAA) technique and radiometric determination of elements are adopted through this work. The selection of the technique is based on less time consumption, high accuracy, reliability, selectivity as well as chemical processing and separation need not to applied. Together with INAA determination of natural radioactivity are also adopted for accessing certain specific elements of importance to the fertilizer industry. Beside the mentioned techniques several classical analytical techniques as atomic absorption, spectrophotometric determination and volumetric methods are handled. 25 tabs., 80 figs., 117 refs

Arsenic in industrial waste water from copper production technological process

Directory of Open Access Journals (Sweden)

Biljana Jovanović

2013-12-01

Full Text Available Investigation of arsenic in industrial waste water is of a great importance for environment. Discharge of untreated waste water from a copper production process results in serious pollution of surface water, which directly affects flora and fauna, as well as humans. There is a need for efficient and environmentally acceptable treament of waste waters containing heavy metals and arsenic. The paper presents an analyisis of the waste water from The Copper Smelter which is discharged into the Bor river. The expected arsenic content in treated waste water after using HDS procedure is also presented.

Multi-objective model of waste transportation management for crude palm oil industry

Science.gov (United States)

Silalahi, Meslin; Mawengkang, Herman; Irsa Syahputri, Nenna

2018-02-01

The crude palm oil industry is an agro-industrial commodity. The global market of this industry has experienced rapid growth in recent years, such that it has a strategic value to be developed for Indonesian economy. Despite these economic benefits there are a number of environmental problems at the factories, such as high water consumption, the generation of a large amount of wastewater with a high organic content, and the generation of a large quantity of solid wastes and air pollution. In terms of waste transportation, we propose a multiobjective programming model for managing business environmental risk in a crude palm oil manufacture which gives the best possible configuration of waste management facilities and allocates wastes to these facilities. Then we develop an interactive approach for tackling logistics and environmental risk production planning problem for the crude palm oil industry.

Treatment of refractory organic pollutants in industrial wastewater by wet air oxidation

Directory of Open Access Journals (Sweden)

Mingming Luan

2017-02-01

Full Text Available Wet air oxidation (WAO is one of the most economical and environmentally-friendly advanced oxidation processes. It makes a promising technology for the treatment of refractory organic pollutants in industrial wastewaters. In wet air oxidation aqueous waste is oxidized in the liquid phase at high temperatures (125–320 °C and pressures (0.5–20 MPa in the presence of an oxygen-containing gas (usually air. The advantages of the process include low operating costs and minimal air pollution discharges. The present review is concerned about the literature published in the treatment of refractory organic pollutants in industrial wastewaters, such as dyes. Phenolics were taken as model pollutants in most cases. Reports on effect of treatment for the WAO of refractory organic pollutants in industrial wastewaters are reviewed, such as emulsified wastewater, TNT red water, etc. Discussions are also made on the mechanism and kinetics of WAO and main technical parameters influencing WAO. Finally, development direction of WAO is summed up.

Effect of the waste products storage on the environmental pollution by toxic organic compounds

Directory of Open Access Journals (Sweden)

Aleksandra Lewkiewicz-Małysa

2005-11-01

Full Text Available A permanent deposition of industrial wastes is a method of its neutralization. A storage yard for toxic materials must meet specific site and construction conditions. The storage place region of toxic organic waste materials has to be monitored. The environmental impact of this waste on the groundwater quality, especially the migration of persistent organic pollutants, was discussed on the example of a chemical plant.

The management of industrial wastes in hydrology; La gestion des dechets industriels en hydrologie

Energy Technology Data Exchange (ETDEWEB)

Elbaz-Seboun, V.

1998-07-08

The industrial wastes are made of different kind of wastes: the inert wastes, the banal wastes (municipal wastes), the special wastes containing noxious elements with respect to human health and environment, and the radioactive wastes. Each industry generates its own effluents (sludges from water treatment plants and leachates from rubbish dumps). The main water pollutions are due to the fermentescible organic matters, nitrates and heavy metals from the industrial waste waters. The aim of the public water agencies is to better protect the environment and to give help to the industrialists in the management of their wastes: reduction at the source, selective collection, valorization, transportation and processing. Non-valorizable wastes must be processed: physico-chemical and biological processing (bio-filtering, coagulation-flocculation, membranes and industrial gases), incineration (organic wastes), disposal in class 1 technical burial centres after stabilization (ultimate wastes). Since July 2002, only the ultimate wastes will be disposed off and all class 2 and 3 dumps must have been rehabilitated. This work is divided into 2 parts: part 1 gives a presentation of the different types of industrial wastes and of their management (origin of wastes, effluents, heavy metals, environmental impact, legal aspects, wastes management, valorization). The second part describes the different processes for the treatment of industrial wastes (conventional processes, physico-chemical and biological processes, incineration, tipping, processing of radioactive wastes). (J.S.)

Effects of lead pollution at industrial contaminated sites on sentinel juvenile Achatina achatina.

Science.gov (United States)

Ebenso, I E; Ologhobo, A D

2009-01-01

We investigated juvenile Achatina achatina snails exposed as sentinels in plastic cages for 12 weeks to compare lead pollution at dump sites of abandoned battery factory (Niger Delta, Nigeria). Results indicated 0.56, 20.37, 200.42 and 1200.30 microg/g soil lead at control, storage, dried effluent and waste dump sites, respectively. There were significant (p lead pollution. Snails were tolerant of all levels of lead pollution with no mortalities. This novel approach provides a basis for use of snail data in environmental pollution assessment of industrial sites.

Study on the Pollution-heaven Hypothesis Focusing on Pollution-Intensive Industries

Energy Technology Data Exchange (ETDEWEB)

Lho, S.W. [Kyungnam University, Masan (Korea)

2002-03-01

The purpose of this study is to test pollution-heaven hypothesis on the Korean pollution-intensive industries, that is, textile and clothing, petrochemical and primary metal industry. The empirical study examines that foreign direct investment(FDI) of Korean pollution-intensive industries regresses on couple of exogenous variables and the environmental regulation on FDI. As the environmental regulation is not directly observed, it uses C0{sub 2} emissions as the pollutant. The results of the study show that the environmental regulation in a host country is an insignificant determinant of FDI for the Korean polluting industries. That is, they do not support Leonard (1988), Xing and Kolstad (2000) that the hypothesis is a significant for heavily polluting industries. (author). 34 refs., 10 tabs.

Environmental impact of industrial wastes on marine area, case study: Port Sudan coastal area

International Nuclear Information System (INIS)

Abdalrahman, E. A. H.

2004-05-01

This study was carried out to determine the effect of the industrial wastes on marine environment in Port Sudan area. A very intensive study has been made to identify types of pollutions drained in seawater at study area of Red Sea coast. Samples were taken from three stations (1, 2 and 3) at study area and the following analysis were made: Temperature, salinity, hydrogen ion concentration, dissolved oxygen, biochemical oxygen demand, nutrient, oil and grease. The laboratory results revealed that wastes pollute the marine environment as the cooling water from studied industries which is drain into the seawater increases the degree of temperature approximately from 6 to 12 C degree above the allowed rate, the matter which was adverse effect on the environment and living marine creatures due to the sudden change of temperature degree. Also, it was found that the great amount of oil spills discharged into seawater due to many factors such as: cooling water, oil spills from ships and loading and discharging operations of crude oil ships. Accordingly these oils spills might have a deadly effect on living marine creatures, which have been mention in details through out this research. Hence, and to minimize this adverse effect of industrial wastes and others on the marine environment, may recommend to the following: Pretreatment to the industrial wastes should be taking before its draining into the Red Sea coastal area. Surveillance all ships into the port and observing loading and discharging operations as well as those ships in the regional waters and implementing the international maritime laws. Enlightenment the industrial administrators and manpower working with them about the severity which will definitely cause the marine environmental deterioration as a result of industrial wastes. To punish every one who violates the laws of environment protection. Thus, can be safeguarding the environment from pollutions and consequently develop the natural resources and proceed

Valorization of solid waste products from olive oil industry as potential adsorbents for water pollution control--a review.

Science.gov (United States)

Bhatnagar, Amit; Kaczala, Fabio; Hogland, William; Marques, Marcia; Paraskeva, Christakis A; Papadakis, Vagelis G; Sillanpää, Mika

2014-01-01

The global olive oil production for 2010 is estimated to be 2,881,500 metric tons. The European Union countries produce 78.5% of the total olive oil, which stands for an average production of 2,136,000 tons. The worldwide consumption of olive oil increased of 78% between 1990 and 2010. The increase in olive oil production implies a proportional increase in olive mill wastes. As a consequence of such increasing trend, olive mills are facing severe environmental problems due to lack of feasible and/or cost-effective solutions to olive-mill waste management. Therefore, immediate attention is required to find a proper way of management to deal with olive mill waste materials in order to minimize environmental pollution and associated health risks. One of the interesting uses of solid wastes generated from olive mills is to convert them as inexpensive adsorbents for water pollution control. In this review paper, an extensive list of adsorbents (prepared by utilizing different types of olive mill solid waste materials) from vast literature has been compiled, and their adsorption capacities for various aquatic pollutants removal are presented. Different physicochemical methods that have been used to convert olive mill solid wastes into efficient adsorbents have also been discussed. Characterization of olive-based adsorbents and adsorption mechanisms of various aquatic pollutants on these developed olive-based adsorbents have also been discussed in detail. Conclusions have been drawn from the literature reviewed, and suggestions for future research are proposed.

THE IMPACT OF INDUSTRIAL WASTE LANDFILL ON THE ENVIRONMENT

Directory of Open Access Journals (Sweden)

Monika Janas

2017-06-01

Full Text Available The aim of the study is to assess the environmental impact of a shut down industrial waste landfill. A detailed analysis of the quality of groundwater around the landfill in the years 1995-2016 was conducted. Assessment of the status of groundwater in the landfill area was made based on the results of monitoring tests. It includes the measurement of pH, specific electrical conductivity (SEC and the content of chlorides, sulfates, phosphates, heavy metals: copper (Cu, lead (Pb, chromium (Cr and a number of other pollution indicators. The analysis confirms that the landfill during the operation did not constitute a threat because of a number of employed security measures and sealing layers. Only in recent years, the industrial waste landfill which is already out of operation has become an extremely serious environmental threat. The results of water analyses from the piezometers clearly indicate that there is a problem of groundwater contamination. There was a significant increase in the value of some of the analyzed indicators (such as chlorides and sulfates, mainly in the piezometers located on the flow line of groundwater in the landfill area. The observed situation is probably a result of damage to the sealing layers and leaching of pollutants from waste deposited in the landfill by rain water.

Waste Minimization and Pollution Prevention Awareness Plan

International Nuclear Information System (INIS)

1992-01-01

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) and other legal requirements that are discussed in Section C, below. The Pollution Prevention Awareness Program is included with the Waste Minimization Program as suggested by DOE Order 5400.1. The intent of this plan is to respond to and comply with the Department's policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Directorate-, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Directorates, Programs and Departments. Several Directorates have been reorganized, necessitating changes in the Directorate plans that were published in 1991

Waste minimization and pollution prevention awareness plan

International Nuclear Information System (INIS)

1991-01-01

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs

Waste minimization and pollution prevention awareness plan

Energy Technology Data Exchange (ETDEWEB)

1991-05-31

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs.

Fruit stones from industrial waste for the removal of lead ions from polluted water.

Science.gov (United States)

Rashed, M N

2006-08-01

Lead, one of the earliest metals recognized and used by humans, has a long history of beneficial use. However, it is now recognized as toxic and as posing a widespread threat to humans and wildlife. Treatment of lead from polluted water and wastewater has received a great deal of attention. Adsorption is one of the most common technologies for the treatment of lead-polluted water. This technique was evaluated here, with the goal of identifying innovative, low-cost adsorbent. This study presents experiments undertaken to determine the suitable conditions for the use of peach and apricot stones, produced from food industries as solid waste, as adsorbents for the removal of lead from aqueous solution. Chemical stability of adsorbents, effect of pH, adsorbents dose, adsorption time and equilibrium concentration were studied. The results reveal that adsorption of lead ions onto peach stone was stronger than onto apricot stone up to 3.36% at 3 h adsorption time. Suitable equilibrium time for the adsorption was 3-5 h (% Pb adsorption 93% for apricot and 97.64% for peach). The effective adsorption range for pH in the range was 7-8. Application of Langmuir and Freundlich isotherm models show high adsorption maximum and binding energies for using these adsorbents for the removal of lead ions from contaminated water and wastewater.

Comprehensive Planning for Classification and Disposal of Solid Waste at the Industrial Parks regarding Health and Environmental Impacts

Directory of Open Access Journals (Sweden)

Hassan Hashemi

2014-01-01

Full Text Available The aim of this study is the comprehensive planning for integrated management of solid waste at the industrial parks. The share of each industrial group including food, metal, chemical, non-metallic minerals, textile, electrical and electronical, and cellulose industries were 48.2, 14.9, 6.7, 22, 0.9, 0.6, and 6.5 percent, respectively. The results showed that nearly half of total industrial waste produced from the range of biological materials are biodegradable and discharging them without observing environmental regulations leads to short-term pollution and nuisance in the acceptor environment. Also some parts of case study waste were recyclable which is considerable from viewpoint of economical and environmental pollution. Long-term impacts will appear due to improper site selection of disposal from the spatial standpoint. In this way, an approach for site selection using several socioeconomic, physical, and environmental criteria based on multicriteria decision making model (MCDM is introduced. Health risks and environment pollution such as soil and surface water may be done. It is essential to revise the studied industries layout, particularly those units which produce special waste which should be more cautious. Also stricter enforcement is required as an effective step in reducing the harmful impacts of it.

Waste Management in Industrial Construction: Investigating Contributions from Industrial Ecology

Directory of Open Access Journals (Sweden)

Larissa A. R. U. Freitas

2017-07-01

Full Text Available The need for effective construction waste management is growing in importance, due to the increasing generation of construction waste and to its adverse impacts on the environment. However, despite the numerous studies on construction waste management, recovery of construction waste through Industrial Symbiosis and the adoption of other inter-firm practices, comprised within Industrial Ecology field of study, have not been fully explored. The present research aims to investigate Industrial Ecology contributions to waste management in industrial construction. The waste management strategies adopted in two industrial construction projects in Brazil are analyzed. The main waste streams generated are identified, recycling and landfilling diversion rates are presented and waste recovery through Industrial Symbiosis is discussed. A SWOT analysis was carried out. Results demonstrate that 9% of the waste produced in one of the projects was recovered through Industrial Symbiosis, while in the other project, waste recovery through Industrial Symbiosis achieved the rate of 30%. These data reveal Industrial Symbiosis’ potential to reduce landfilling of industrial construction wastes, contributing to waste recovery in construction. In addition, results show that industrial construction projects can benefit from the following synergies common in Industrial Ecology place-based approaches: centralized waste management service, shared waste management infrastructure and administrative simplification.

Waste Minimization/Pollution Prevention Crosscut Plan, 1994

International Nuclear Information System (INIS)

1994-01-01

This plan establishes a Department-wide goal to reduce total releases of toxic chemicals to the environment and off-site transfers of such toxic chemicals by 50 percent by December 31, 1999, in compliance with Executive Order 12856. Each site that meets the threshold quantities of toxic chemicals established in the Emergency Planning and Community Right-to-Know Act (EPCRA) will participate in this goal. In addition, each DOE site will establish site-specific goals to reduce generation of hazardous, radioactive, radioactive mixed, and sanitary wastes and pollutants, as applicable. Implementation of this plan will represent a major step toward the environmental risks and costs associated with DOE operations and increasing the Department's use of preventive environmental management practices. Investing in Waste Minimization Pollution Prevention (WMin/PP) steadily reduce hazardous and radioactive waste generation and will reduce the need for waste management and unnecessary expenditures for waste treatment, storage, and disposal. A preventive approach to waste management will help solve current environmental and regulatory issues and reduce the need for costly future corrective actions. The purpose of this plan is to establish the strategic framework for integrating WMin/PP into all DOE internal activities. This program includes setting DOE policy and goals for reducing the generation of wastes and pollutants, increasing recycling activities, and establishing an infrastructure to achieve and measure the goals throughout the DOE complex. Waste Minimization and Pollution Prevention Awareness Plans, submitted to Headquarters by DOE field sites, will incorporate the WMin/PP activities and goals outlined in this plan. Success of the DOE WMin/PP program is dependent upon each field operation becoming accountable for resources used, wastes and pollutants generated, and wastes recycled

Status of water pollution in relation to industrialization in Rajasthan.

Science.gov (United States)

Rajput, Ritu Singh; Pandey, Sonali; Bhadauria, Seema

2017-09-26

India is a large and densely populated country; its economy is largely agricultural. Making the best use of the country's manpower has always posed a challenge. Industrialization could become a dominant component of the economy and displace agriculture. Traditional livelihoods of occupational groups are threatened by the practice of disposing untreated industrial waste into rivers and bodies of water. These uncontrolled disposals impact local natural resources with negative long-term effects. Industrialization is the development of intellectual and financial trade that changes a predominantly rustic culture into a modern one. Many industrial units discharge wastewater locally without treatment. Many industries directly discharged their waste into lakes, rivers and ocean. Water contamination impacts the environment. Pesticides, chemical, waste oil and heavy metals are regularly transported into their waters. Humans and other living organisms can accumulate heavy metals from industrial discharges in their tissues. Industrial waste may be reactive, corrosive, flammable, or toxic. When untreated sewage is emptied into rivers, it causes diseases like typhoid, dysentery and cholera. Natural elements and plant supplements like nitrate and phosphates stimulate growth of algae on the water surface. The algae reduce the oxygen in the water and cause eutrophication. It is harmful to the water ecosystem. In Rajasthan proper, there are a number of sites bordering rivers and lakes where the pace of industrialization has proceeded far beyond the ability of regulators to establish and enforce meaningful limits on the amount of point source pollution permitted to the various industrial complexes, which include cement, chemical, fertilizer, textile, mining, quarrying, dyeing and printing facilities. The scale of the problem is obvious to the casual observer, but actual documentation of the total impact remains to be done.

Influence of industrial solid waste addition on properties of soil-cement bricks

Directory of Open Access Journals (Sweden)

F. B. Siqueira

Full Text Available Abstract The reuse of pollutant solid wastes produced in distinct industrial activities (avian eggshell waste and welding flux slag waste as a source of alternative raw material for producing soil-cement bricks for civil construction was investigated. Soil-cement bricks containing up to 30 wt% of industrial solid waste were uniaxially pressed and cured for 28 days. Special emphasis is given on the influence of solid waste addition on the technical properties (as such volumetric shrinkage, water absorption, bulk density, durability, and compressive strength, microstructure and mineral phases of soil-cement bricks. Microstructural evolution was evaluated via confocal microscopy. The experimental results showed that the solid wastes behave as charge material and influenced both technical properties and microstructure of the soil-cement bricks. It was found that up to 15 wt% of welding flux slag waste and up to 30 wt% of avian eggshell waste could be added into the soil-cement bricks for use as building material.

Hot particles in industrial waste and mining tailings

CERN Document Server

Selchau-Hansen, K; Freyer, K; Treutler, C; Enge, W

1999-01-01

Industrial waste was studied concerning its radioactive pollution. Using known properties of the solid state nuclear track detector CR-39 we found among a high concentration of more or less homogeneously distributed single alpha-tracks discrete spots of very high enrichments of alpha-particles created by so called hot particles. We will report about the alpha-activity, the concentration of hot particles and about their ability to be air borne.

Waste minimization/pollution prevention study of high-priority waste streams

International Nuclear Information System (INIS)

Ogle, R.B.

1994-03-01

Although waste minimization has been practiced by the Metals and Ceramics (M ampersand C) Division in the past, the effort has not been uniform or formalized. To establish the groundwork for continuous improvement, the Division Director initiated a more formalized waste minimization and pollution prevention program. Formalization of the division's pollution prevention efforts in fiscal year (FY) 1993 was initiated by a more concerted effort to determine the status of waste generation from division activities. The goal for this effort was to reduce or minimize the wastes identified as having the greatest impact on human health, the environment, and costs. Two broad categories of division wastes were identified as solid/liquid wastes and those relating to energy use (primarily electricity and steam). This report presents information on the nonradioactive solid and liquid wastes generated by division activities. More specifically, the information presented was generated by teams of M ampersand C staff members empowered by the Division Director to study specific waste streams

Environmental Restoration Contractor Waste Minimization and Pollution Prevention Plan

International Nuclear Information System (INIS)

Lewis, R.A.

1994-11-01

The purpose of this plan is to establish the Environmental Restoration Contractor (ERC) Waste Minimization and Pollution Prevention (WMin/P2) Program and outline the activities and schedules that will be employed to reduce the quantity and toxicity of wastes generated as a result of restoration and remediation activities. It is intended to satisfy the US Department of Energy (DOE) and other legal requirements. As such, the Pollution Prevention Awareness program required by DOE Order 5400.1 is included with the Pollution Prevention Program. This plan is also intended to aid projects in meeting and documenting compliance with the various requirements for WMin/P2, and contains the policy, objectives, strategy, and support activities of the WMin/P2 program. The basic elements of the plan are pollution prevention goals, waste assessments of major waste streams, implementation of feasible waste minimization opportunities, and a process for reporting achievements. Various pollution prevention techniques will be implemented with the support of employee training and awareness programs to reduce waste and still meet applicable requirements. Information about the Hanford Site is in the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan

Pollution and energy management in tanning industry

International Nuclear Information System (INIS)

Zaman, N.U.

2005-01-01

Tanning industry uses a number of chemicals such as Common Salt, Lime (Calcium Hydroxide), Sodium Sulfide and Basic Chromium Sulfate etc. During process, only a part of the chemical is consumed and the rest ends up in the effluent as pollutant. This paper deals with the techniques, locally developed or published in literature to recycle these chemicals and also discusses some energy saving techniques which can be used in tanning industry. Basic Chromium Sulfate (BCS) is one of the expensive chemicals used in 'Chrome Tanning'. By precipitating d filtering basic chromium sulfate, the recovery is nearly complete and the effluent obtained contains less than 1ppm Chromium. Dried raw hides contain up to 15% sodium chloride (w/w) and this can be removed in solid form by using mechanical brushes and can be re-used. The recovered salt contains foreign matter as impurities. After dissolution in water, the salt solution is filtered through cartridge filters and can be used in pickle bath. Liming slurry containing sodium sulfide is wasted as it contains fleshing and hair etc. A self cleaning 'J' type screen has no moving parts and removes fleshing and hair from the lime suspension. 'Counter Current Washing Technique,' reduces the wash water quantity by a factor of five to six. Air born pollution generated during buffing and dyeing can be captured by properly designed air filters. The solvents released in atmosphere during dyeing and finishing can be recovered by absorption. Fat, gelatin and protein can be recovered from waste fleshing. In tanning industry, drying of hides is the major consumer of thermal energy. Hot air can be produced by steam, hot water or solar energy. Advantages and disadvantages of these options are discussed. Wastage of thermal energy in dryers can be reduced by improving the existing designs. Hot water for tanning purposes can be generated by recovering waste heat present in the boiler flue gases. Boiler efficiency can also be improved by cycling heat

Remediation of lead from lead electroplating industrial effluent using sago waste.

Science.gov (United States)

Jeyanthi, G P; Shanthi, G

2007-01-01

Heavy metals are known toxicants, which inflict acute disorders to the living beings. Electroplating industries pose great threat to the environment through heavy load of metals in the wastewater discharged on land and water sources. In the present study, sago processing waste, which is both a waste and a pollutant, was used to adsorb lead ions from lead electroplating industrial effluent. Two types of sago wastes, namely, coarse sago waste and fine sago waste were used to study their adsorption capacity with the batch adsorption and Freundlich adsorption isotherm. The parameters that were considered for batch adsorption were pH (4, 5 and 6), time of contact (1, 2 and 3 hrs), temperature (30, 37 and 45 degrees C) and dosage of the adsorbent (2,4 and 6 g/L). The optimal condition for the effective removal of lead was found to be pH 5, time of contact 3 hrs, temperature 30 degrees C and dosage 4 g/L with coarse sago waste than fine sago waste.

Study of ants as bioindicators of industrial pollution in Kemerovo Region, Russia

Science.gov (United States)

Blinova, S. V.; Dobrydina, T. I.

2018-01-01

The myrmecocomplexes of five industrial cities in the territory of Kuzbass, Russia, were studied. The general trends in the reaction of ants to the pollution by gaseous (chemical industry) and solid (coal and cement dust, lead and zinc waste and metallurgical industry) emissions were revealed. It was found out that the proportion of species of subfamilies, species richness and density of the settlement can be used as bioindicators. The predominance of L. niger and M. rubra nests in myrmecocomplexes immediately indicates a high degree of man-made impact.

Industrial waste heat for district heating

International Nuclear Information System (INIS)

Heitner, K.L.; Brooks, P.P.

1982-01-01

Presents 2 bounding evaluations of industrial waste heat availability. Surveys waste heat from 29 major industry groups at the 2-digit level in Standard Industrial Codes (SIC). Explains that waste heat availability in each industry was related to regional product sales, in order to estimate regional waste heat availability. Evaluates 4 selected industries at the 4-digit SIC level. Finds that industrial waste heat represents a significant energy resource in several urban areas, including Chicago and Los Angeles, where it could supply all of these areas residential heating and cooling load. Points out that there is a strong need to evaluate the available waste heat for more industries at the 4-digit level. Urges further studies to identify other useful industrial waste heat sources as well as potential waste heat users

Potentialities of biotechnology for the reduction and utilization for energy purposes of wastes generated by food industry

Energy Technology Data Exchange (ETDEWEB)

1982-10-19

The study dealt with the present trends in biotechnology related to the methods for the reduction and utilization, for energy purposes, of wastes generated by food industry and to the methods for controlling the emission of pollutants from industrial plants with emphasis on meat industry, dairy industry, food-packing trade, sugar industry, vinification, fatty foods, fish meal, beverage industry.

Air pollution control systems and technologies for waste-to-energy facilities

International Nuclear Information System (INIS)

Getz, N.P.; Amos, C.K. Jr.; Siebert, P.C.

1991-01-01

One of the primary topics of concern to those planning, developing, and operating waste-to-energy (W-T-E) [also known as municipal waste combustors (MWCs)] facilities is air emissions. This paper presents a description of the state-of-the-art air pollution control (APC) systems and technology for particulate, heavy metals, organics, and acid gases control for W-T-E facilities. Items covered include regulations, guidelines, and control techniques as applied in the W-T-E industry. Available APC technologies are viewed in detail on the basis of their potential removal efficiencies, design considerations, operations, and maintenance costs

Role of rural solid waste management in non-point source pollution control of Dianchi Lake catchments, China

Institute of Scientific and Technical Information of China (English)

Wenjing LU; Hongtao WANG

2008-01-01

In recent years, with control of the main municipal and industrial point pollution sources and implementation of cleaning for some inner pollution sources in the water body, the discharge of point source pollution decreased gradually, while non-point source pollution has become increasingly distressing in Dianchi Lake catchments. As one of the major targets in non-point source pollution control, an integrated solid waste controlling strategy combined with a technological solution and management system was proposed and implemented based on the waste disposal situation and characteristics of rural solid waste in the demonstration area. As the key technoogy in rural solid waste treatment, both centralized plantscale composting and a dispersed farmer-operated waste treating system showed promise in rendering timely benefits in efficiency, large handling capacity, high quality of the end product, as well as good economic return. Problems encountered during multi-substrates co-com-posting such as pathogens, high moisture content, asyn-chronism in the decomposition of different substrates, and low quality of the end product can all be tackled. 92.5% of solid waste was collected in the demonstration area, while the treating and recycling ratio reached 87.9%, which pre-vented 32.2 t nitrogen and 3.9 t phosphorus per year from entering the water body of Dianchi Lake after imple-mentation of the project.

Status and direction of waste minimization in the chemical and petrochemical industries

Energy Technology Data Exchange (ETDEWEB)

Englande, Junior, A J [Tulane Univ., New Orleans, LA (United States). School of Public Health and Tropical Medicine

1994-12-31

This paper presents an evaluation of the status and direction of toxic/hazardous waste reduction in chemical and petrochemical industries from an international perspective. In almost all cases studied savings have resulted. The importance of pollution prevention by `clean technologies` instead of remediation is stressed. 6 refs., 4 tabs.

Status and direction of waste minimization in the chemical and petrochemical industries

Energy Technology Data Exchange (ETDEWEB)

Englande Junior, A.J. [Tulane Univ., New Orleans, LA (United States). School of Public Health and Tropical Medicine

1993-12-31

This paper presents an evaluation of the status and direction of toxic/hazardous waste reduction in chemical and petrochemical industries from an international perspective. In almost all cases studied savings have resulted. The importance of pollution prevention by `clean technologies` instead of remediation is stressed. 6 refs., 4 tabs.

Hazardous industrial waste management

International Nuclear Information System (INIS)

Quesada, Hilda; Salas, Juan Carlos; Romero, Luis Guillermo

2007-01-01

The appropriate managing of hazardous wastes is a problem little dealed in the wastes management in the country. A search of available information was made about the generation and handling to internal and external level of the hazardous wastes by national industries. It was worked with eleven companies of different types of industrial activities for, by means of a questionnaire, interviews and visits, to determine the degree of integral and suitable handling of the wastes that they generate. It was concluded that exist only some isolated reports on the generation of hazardous industrial wastes and handling. The total quantity of wastes generated in the country was impossible to establish. The companies consulted were deficient in all stages of the handling of their wastes: generation, accumulation and storage, transport, treatment and final disposition. The lack of knowledge of the legislation and of the appropriate managing of the wastes is showed as the principal cause of the poor management of the residues. The lack of state or private entities entrusted to give services of storage, transport, treatment and final disposition of hazardous wastes in the country was evident. (author) [es

Low cost technologies for the industrial waste water treatment; Tecnologia de tratamiento de aguas residuales industriales de bajo coste

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

Nowadays, the industrialism is gradually becoming more and more concerned on the way of reducing the disposal of pollutant waste. As well, he demands solutions for this problem but he usually guests a great disparity of technologies and costs. This article presents three low cost systems for purification of industrial waste water which are suitable for numerous applications.

Environmental Restoration Program waste minimization and pollution prevention self-assessment

International Nuclear Information System (INIS)

1994-10-01

The Environmental Restoration (ER) Program within Martin Marietta Energy Systems, Inc. is currently developing a more active waste minimization and pollution prevention program. To determine areas of programmatic improvements within the ER Waste Minimization and Pollution Prevention Awareness Program, the ER Program required an evaluation of the program across the Oak Ridge K-25 Site, the Oak Ridge National Laboratory, the Oak Ridge Y-12 Plant, the Paducah Environmental Restoration and Waste Minimization Site, and the Portsmouth Environmental Restoration and Waste Minimization Site. This document presents the status of the overall program as of fourth quarter FY 1994, presents pollution prevention cost avoidance data associated with FY 1994 activities, and identifies areas for improvement. Results of this assessment indicate that the ER Waste Minimization and Pollution Prevention Awareness Program is firmly established and is developing rapidly. Several procedural goals were met in FY 1994 and many of the sites implemented ER waste minimization options. Additional growth is needed, however, for the ER Waste Minimization and Pollution Prevention Awareness Program

Radioactive wastes of Nuclear Industry

International Nuclear Information System (INIS)

1995-01-01

This conference studies the radioactive waste of nuclear industry. Nine articles and presentations are exposed here; the action of the direction of nuclear installations safety, the improvement of industrial proceedings to reduce the waste volume, the packaging of radioactive waste, the safety of radioactive waste disposal and environmental impact studies, a presentation of waste coming from nuclear power plants, the new waste management policy, the international panorama of radioactive waste management, the international transport of radioactive waste, finally an economic analysis of the treatment and ultimate storage of radioactive waste. (N.C.)

Industrial waste recycling strategies optimization problem: mixed integer programming model and heuristics

Science.gov (United States)

Tang, Jiafu; Liu, Yang; Fung, Richard; Luo, Xinggang

2008-12-01

Manufacturers have a legal accountability to deal with industrial waste generated from their production processes in order to avoid pollution. Along with advances in waste recovery techniques, manufacturers may adopt various recycling strategies in dealing with industrial waste. With reuse strategies and technologies, byproducts or wastes will be returned to production processes in the iron and steel industry, and some waste can be recycled back to base material for reuse in other industries. This article focuses on a recovery strategies optimization problem for a typical class of industrial waste recycling process in order to maximize profit. There are multiple strategies for waste recycling available to generate multiple byproducts; these byproducts are then further transformed into several types of chemical products via different production patterns. A mixed integer programming model is developed to determine which recycling strategy and which production pattern should be selected with what quantity of chemical products corresponding to this strategy and pattern in order to yield maximum marginal profits. The sales profits of chemical products and the set-up costs of these strategies, patterns and operation costs of production are considered. A simulated annealing (SA) based heuristic algorithm is developed to solve the problem. Finally, an experiment is designed to verify the effectiveness and feasibility of the proposed method. By comparing a single strategy to multiple strategies in an example, it is shown that the total sales profit of chemical products can be increased by around 25% through the simultaneous use of multiple strategies. This illustrates the superiority of combinatorial multiple strategies. Furthermore, the effects of the model parameters on profit are discussed to help manufacturers organize their waste recycling network.

Industrial Pollution Regulation in the EU and in Macedonia, Serbia And Croatia

Directory of Open Access Journals (Sweden)

Aleksandar Chavleski

2013-09-01

Full Text Available Industrial pollution control has substantial impact in the protection of the environment. In the European Union, there’s vast legislation in this field consisting mainly of the Directive on industrial emissions of 2010 aimed at consolidating the so far existing legislation in this field. The new Directive on industrial emissions aims to establish an integrated prevention and control of the pollution arising from industrial activities and it lays down rules designed to prevent or, where that is not practicable, to reduce emissions into air, water and land and to prevent the generation of waste, in order to achieve a high level of protection of the environment taken as a whole. Macedonia, Serbia and Croatia have made significant progress in this field in the recent years as part of their obligations under the Stabilization and Association Process. The purpose of this particular article is to evaluate the degree of alignment and implementation of the environmental legislation in this particular area with the legislation of EU as well its practical application, and to identify the existing deficiencies and necessary steps for action

Waste audit pada industri penyamakan kulit

Directory of Open Access Journals (Sweden)

Prayitno Prayitno

1999-07-01

Full Text Available Waste audit is new environmental activities. to the Indonesia public and the large part of industrial community it is one of the environmental audit activities. Waste audit aims to identify whether the waste that by the industry waste so that metods for minimizing the waste can be found. In the leather tanning industry wasted audit is performend for every step pg the process, started from the raw material strage to the fishing ptocess.

Study of the Barada river environment pollution with poisonous trace elements resulting from tanning and electroplating industry

International Nuclear Information System (INIS)

Khamis, I.; Sarheel, A.; Al-Somel, N.; Al-Masri, M. S.

2001-01-01

Investigation of leather industry impact on Barada river environment, specifically in the eastern part of Damascus was made. Differential samples such as sediments, soil, and plantations from various locations were collected. results show high increase of chromium in river's sediment and soil adjacent to the river banks. However, such increase was not noticed in plantations or tree leaves. Copper and nickel concentrations were also high in sediments due to waste coming out of the electroplating industry. Concentration of titanium, one of the polishing and coloring industry's wastes, was noticed to be rather high too. Concentration of all previous pollutants was noticed to decrease as the distance become farther from the industrial complex. (Author)

A new approach for the extraction of pollutants from wastewaters handled by the graphic industry.

Science.gov (United States)

Monteiro, C; Ventura, C; Martins, F

2013-06-15

It is widely recognized that the Graphic Industry handles toxic products and produces, in its various operations, toxic wastes. These wastes can cause serious environmental damages and can lead to severe health problems. In this work we report an efficient, simple and cheap to run method for the removal of some of the most common pollutants involved in the various stages of the Graphic Industry production, using a Solid-Phase Extraction (SPE) methodology. We have determined equilibrium constants, K(eq), and adsorption (k(up)) and desorption (k(off)) rate constants for the extraction of benzene, xylene, toluene and ethylbenzene (BXTE) from water, using C18 disks. The removal of these compounds was monitored by UV-vis spectroscopy, at room temperature. Average extraction efficiencies were of 60% in a mixture of BXTEs and close to 80% when pollutants were assessed separately. Since the retention mechanism in the C18 disk is essentially governed by hydrophobic interactions between the compounds and the alkyl chains of the disk, we have also shown that these pollutants' lipophilicity plays an important role in the rationalization of their behavior during the extraction process. Copyright © 2013 Elsevier Ltd. All rights reserved.

Annual report of waste generation and pollution prevention progress 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This Annual Report summarizes and highlights waste generation, waste reduction, pollution prevention accomplishments, and cost avoidance for 44 U.S. Department of Energy reporting sites for Calendar Year 1999. This section summarizes Calendar Year 1999 Complex-wide waste generation and pollution prevention accomplishments.

Annual report of waste generation and pollution prevention progress 1999

International Nuclear Information System (INIS)

2000-01-01

This Annual Report summarizes and highlights waste generation, waste reduction, pollution prevention accomplishments, and cost avoidance for 44 U.S. Department of Energy reporting sites for Calendar Year 1999. This section summarizes Calendar Year 1999 Complex-wide waste generation and pollution prevention accomplishments

Industry

International Nuclear Information System (INIS)

Schindler, I.; Wiesenberger, H.

2001-01-01

This chapter of the environmental control report deals with the environmental impact of the industry in Austria. It gives a review of the structure and types of the industry, the legal framework and environmental policy of industrial relevance. The environmental situation of the industry in Austria is analyzed in detail, concerning air pollution (SO 2 , NO x , CO 2 , CO, CH 4 , N 2 O, NH 3 , Pb, Cd, Hg, dioxin, furans), waste water, waste management and deposit, energy and water consumption. The state of the art in respect of the IPPC-directives (European Integrated Pollution Prevention and Control Bureau) concerning the best available techniques of the different industry sectors is outlined. The application of European laws and regulations in the Austrian industry is described. (a.n.)

Wastes, effluents and pollution. impact on environment

International Nuclear Information System (INIS)

Ngo, Ch.; Regent, A.

2008-01-01

From concrete examples, the authors explain the nature, and the place of different pollution and wastes sources in our environment and the risks that make run. They bring some tracks to our modern communities that must react and imagine remedial actions to manage wastes, effluents and pollutions in order to make them harmless; this new edition enriches of a chapter on health and hygiene problems induced by the different contaminations of environment. (N.C.)

Air Pollution and Industry.

Science.gov (United States)

Ross, R. D., Ed.

This book is an authoritative reference and practical guide designed to help the plant engineer identify and solve industrial air pollution problems in order to be able to meet current air pollution regulations. Prepared under the editorial supervision of an experienced chemical engineer, with each chapter contributed by an expert in his field,…

Study of non-Hodgkin's lymphoma mortality associated with industrial pollution in Spain, using Poisson models

Directory of Open Access Journals (Sweden)

Lope Virginia

2009-01-01

Full Text Available Abstract Background Non-Hodgkin's lymphomas (NHLs have been linked to proximity to industrial areas, but evidence regarding the health risk posed by residence near pollutant industries is very limited. The European Pollutant Emission Register (EPER is a public register that furnishes valuable information on industries that release pollutants to air and water, along with their geographical location. This study sought to explore the relationship between NHL mortality in small areas in Spain and environmental exposure to pollutant emissions from EPER-registered industries, using three Poisson-regression-based mathematical models. Methods Observed cases were drawn from mortality registries in Spain for the period 1994–2003. Industries were grouped into the following sectors: energy; metal; mineral; organic chemicals; waste; paper; food; and use of solvents. Populations having an industry within a radius of 1, 1.5, or 2 kilometres from the municipal centroid were deemed to be exposed. Municipalities outside those radii were considered as reference populations. The relative risks (RRs associated with proximity to pollutant industries were estimated using the following methods: Poisson Regression; mixed Poisson model with random provincial effect; and spatial autoregressive modelling (BYM model. Results Only proximity of paper industries to population centres (>2 km could be associated with a greater risk of NHL mortality (mixed model: RR:1.24, 95% CI:1.09–1.42; BYM model: RR:1.21, 95% CI:1.01–1.45; Poisson model: RR:1.16, 95% CI:1.06–1.27. Spatial models yielded higher estimates. Conclusion The reported association between exposure to air pollution from the paper, pulp and board industry and NHL mortality is independent of the model used. Inclusion of spatial random effects terms in the risk estimate improves the study of associations between environmental exposures and mortality. The EPER could be of great utility when studying the effects of

Wear Behavior of Aluminium Metal Matrix Composite Prepared from Industrial Waste

Directory of Open Access Journals (Sweden)

L. Francis Xavier

2016-01-01

Full Text Available With an increase in the population and industrialization, a lot of valuable natural resources are depleted to prepare and manufacture products. However industrialization on the other hand has waste disposal issues, causing dust and environmental pollution. In this work, Aluminium Metal Matrix Composite is prepared by reinforcing 10 wt% and 20 wt% of wet grinder stone dust particles an industrial waste obtained during processing of quarry rocks which are available in nature. In the composite materials design wear is a very important criterion requiring consideration which ensures the materials reliability in applications where they come in contact with the environment and other surfaces. Dry sliding wear test was carried out using pin-on-disc apparatus on the prepared composites. The results reveal that increasing the reinforcement content from 10 wt% to 20 wt% increases the resistance to wear rate.

Solutions for energy recovery of animal waste from leather industry

International Nuclear Information System (INIS)

Lazaroiu, Gheorghe; Pană, Constantin; Mihaescu, Lucian; Cernat, Alexandru; Negurescu, Niculae; Mocanu, Raluca; Negreanu, Gabriel

2017-01-01

Highlights: • Animal fats in blend with diesel fuel for energy valorification through combustion. • Animal waste from tanneries as fuel and for biogas production. • Experimental tests using animal fats as fuel for diesel engines. • Experimental tests modifying the characteristic parameters. - Abstract: Secondary products from food and leather industries are regarded as animal wastes. Conversion of these animal wastes into fuels represents an energy recovery solution not only because of their good combustion properties, but also from the viewpoint of supply stability. A tannery factory usually processes 60–70 t/month of crude leathers, resulting in 12–15 t/month of waste. Fats, which can be used as the input fuel for diesel engines (in crude state or as biodiesel), represent 10% of this animal waste, while the rest are proteins that can be used to generate biogas through anaerobic digestion. Herein, we analyse two approaches to the use of animal waste from tanneries: as fuel for diesel engines and for biogas generation for heat production. Diesel fuelling and fuelling by animal wastes are compared in terms of the engine performance and pollutant emissions. The effects of animal waste usage on the pollutant emissions level, exhaust gas temperature, indicated mean effective pressure, maximum pressure, and engine efficiency are analysed. The energy recovery technologies for animal waste, which are analysed in this work, can be easily implemented and can simultaneously solve the problem posed by animal wastes by using them as an alternative to fossil fuels. Animal fats can be considered an excellent alternative fuel for diesel engines without major constructive modifications.

Waste Management in Industrial Construction: Investigating Contributions from Industrial Ecology

OpenAIRE

Larissa A. R. U. Freitas; Alessandra Magrini

2017-01-01

The need for effective construction waste management is growing in importance, due to the increasing generation of construction waste and to its adverse impacts on the environment. However, despite the numerous studies on construction waste management, recovery of construction waste through Industrial Symbiosis and the adoption of other inter-firm practices, comprised within Industrial Ecology field of study, have not been fully explored. The present research aims to investigate Industrial Ec...

Energy from wastes and the private waste contracting industry

International Nuclear Information System (INIS)

Burnett, J.S.

1993-01-01

The focus of this ongoing work is the utilisation of general non hazardous industrial and commercial waste as an energy or fuel source. Whereas much of the existing experience in energy from waste (EFW) is related to municipal solid wastes (MSW), there is very little direct experience with these other waste streams and the shortage of reliable information in this field is notoriously lacking. It is important to have a good understanding of the private waste contracting industry (pwci) in order to establish the conditions under which energy from waste technologies may play an economically and technically feasible role within that industry's development. The Non Fossil Fuel Obligation (NFFO) has encouraged entrepreneurial interest through premium payments for electricity generated from renewable sources. (author)

Hazardous and Industrial Wastes Management: a Case Study of Khazra Industrial Park, Kerman

Directory of Open Access Journals (Sweden)

Hossein Jafari Mansoorian

2013-08-01

Full Text Available Background & Aims of the Study: Increasing hazardous industrial wastes and lack of necessary regulations for management of them have led to serious problems in some parts of Iran. The aim of this study was to evaluate the situation of collection, transportation, recycling, and disposal of hazardous industrial wastes in the Khazra Industrial Park of Kerman, Iran. Materials & Methods: This study was a descriptive cross-sectional study that was done using questionnaires and local visits during year 2009. In this questionnaire, some information about the industrial wastes, production, storage on site , collection, transformation, sorting, recycling, and disposal were recorded. Results:   In the Khazra Industrial Park, 71,600 kg/day of different industrial waste is produced. The biggest proportion of waste includes metals, and construction and demolition waste which are about 16,500 tons a year. The smallest proportion is non-iron metal waste, which is produced at a rate of 8 tons per year. 88.7 percent of the active industries at the Khazra Industrial Park produce solid industrial waste. Most of the industrial units do not use a united and coordinated system for storing waste and have no specific place for temporary storage inside the industrial park. The majority of industrial waste collection, which is about 59.8%, is done by private contractors. The industrial units transfer their waste separately, and just 9 industrial units recycle their waste. Disposal of these wastes is mainly done by selling to trading agencies. Each day, 3 tons of hazardous industrial waste is produced in this park. The highest production belongs to the oil factory (Keyhan Motor. Conclusions: According to the results, the Khazra Industrial Park needs a unified system for storing, transporting and collecting the sorted waste, and it also needs to have a transportation station with basic facilities. The wastes of most industrial units at the Khazra Industrial Park have the

Monitoring persistent organic pollutants in an industrial area of Tarragona (Catalonia, Spain)

Energy Technology Data Exchange (ETDEWEB)

Nadal, M.; Schuhmacher, M.; Domingo, J.L. [Rovira i Virgili University, Reus (Spain)

2004-09-15

It is well known that combustion of different materials is one of the most important sources of environmental contamination by persistent organic pollutants (POPs). Therefore, environments affected by this kind of processes should be strictly controlled. In relation to it, the 2001 Stockholm Convention for the regulation of POPs was undertaken in order to establish agreements and mechanisms to erase the release of 12 POPs on a global scale. While polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) and polychlorinated biphenyls (PCBs) were included in this list, other pollutants such as polychlorinated naphthalenes (PCNs) and polycyclic aromatic hydrocarbons (PAHs) can be added in a near future. Since more than 30 years ago, one of the largest chemical and petrochemical industrial complexes in Southern Europe is located in Tarragona County (Catalonia, Spain). Several chemical industries (such as a PVC production facility and a chlor-alkali plant) and a big oil refinery are located in this residential area (up to 300,000 inhabitants), together with a municipal solid waste incinerator (MSWI) and a hazardous waste incinerator (HWI). Moreover, the presence of a highway and several roads with an important traffic density influences also the environment of the zone. The current study is a preliminary investigation to assess the levels of several POPs (PCDD/Fs, PCBs, PCNs and PAHs) in soil and vegetation samples collected in Tarragona's industrial and residential areas and to compare them with data obtained in unpolluted sites as well as in other industrial and residential zones.

The treatment and disposal of liquid waste in the nuclear power industry

International Nuclear Information System (INIS)

Lewis, J.B.

1978-01-01

Paper presented by the head of the Industrial Chemistry Group at AERE Harwell at a symposium held by the University of Newcastle upon Tyne (UK) in association with the Institute of Water Pollution Control and the Institution of Chemical Engineers in September 1977. Main headings are as follows: general introduction; units of measurement of radioactivity; environmental considerations (disposal authorisations, natural background, critical path approach, discharges to the sea, discharges to rivers); types of liquid waste (general, high level wastes, wastes from chemical processing stages, wastes from nuclear power stations, miscellaneous wastes); treatment techniques (general, evaporation, chemical precipitation, ion exchange, reverse osmosis, electrodialysis); disposal of radioactive concentrates (high level wastes, sludges, exhausted ion exchangers, etc.). It is concluded that the main task remaining is to find the best means of ultimate disposal of high level wastes. (U.K.)

Trees as bioindicators of industrial air pollution during implementation of pro-environmental policy in Silesia region (Poland).

Science.gov (United States)

Sensuła, Barbara; Wilczyński, Slawomir; Opała, Magdalena; Pawełczyk, Sławomira; Piotrowska, Natalia

2015-04-01

The aim of research conducted within the project entitled "Trees as bioindicators of industrial air pollutants during the implementation of pro-environmental policies in the area of Silesia" (acronym BIOPOL) is the reconstruction of climate changes and anthropogenic effects and monitoring of the influence of human activities related to industrial development and the introduction of pro-environmental policy. The analysis will concern the climatic and anthropogenic signals recorded in annual tree rings width of Scots pine and in the isotopic composition of wood and its compenents (such as alpha-cellulose and glucose). Only a few studies made a complex multiproxies analysis of the influence of industrial air pollutants on changes in the tree rings width and their isotopic composition in any selected region. In addition, research is usually for a period of industrial development, is a lack of analysis for the period of implementation of EU law and standards on air quality to Polish law. The research area are the forests close to 3 different industrial plants (chemical- nitrogen plants, steel mills, power plants), in Silesia, where operating companies have strategic importance for the region and country. By analyzing the structure of land in Silesia noted a significant advantage of forest land and agricultural land. A large percentage of forest land providing protection for residents in case of failure in any of the plants. A cloud of noxious fumes is possible in large part retained in the trees. Waste generated by the chemical industry, metallurgy and energy represent the largest proportion of waste generated in the region. Already in the beginning of 21stcentury, the Waste Management Plans for various cities in Silesia are set out various strategic objectives to 2015, including in the economic sector: the implementation of non-waste technology and less and the best available techniques (BAT), the introduction of the principles of "cleaner production". The BIOPOL

The Effectiveness of Mendong Plant (Fimbrystilis Globulosa) as a Phytoremediator of Soil Contaminated with Chromium of Industrial Waste

OpenAIRE

Ferina, Pungky; Rosariastuti, Retno; Supriyadi, S

2017-01-01

The textile industry produces sideline output in the form of dangerous waste. The textile industrial waste containing heavy metal, one of which is Chromium (Cr).  Chromium is very dangerous metal for environment, especially chromium hexavalent that has properties of soluble, carcinogenic, and toxic. The pollution of chromium in soil is a problem that the action to be taken with the technology of bioremediation. Phytoremediation of soil contaminated with chromium using Mendong plant (Fimbrysti...

River pollution caused by natural stone industry

Science.gov (United States)

Oktriani, Ani; Darmajanti, Linda; Soesilo, Tri Edhi Budhi

2017-03-01

The natural stone industry is classified as small industry. Current wastewater treatment still causes pollution in the river. This thesis aims to analyze the performance of wastewater treatment in natural stones industry. The data was collected from water quality test (parameters: temperature, pH, DO, and TSS). The wastewater treatment performance was in a slightly higher position compared to the 2nd class quality standards of Government Regulation No. 82/2001. The parameter that exceeded quality standards was the concentration of TSS, which was up to 240.8 mg/l. The high concentration of TSS was affected by the absence of sludge management schedule, which resulted in non-optimal precipitation. Besides that, the design of sedimentation basin was still not adapted with wastewater debit. Referring to the results, this study suggests the government of Cirebon District to provide wastewater treatment development through the village staff. Furthermore, the government also needs to give strict punishment to business owner who does not treat waste correctly and does not have a business license. Moreover, the sale value of sludge as byproduct of wastewater treatment needs to be increased.

Water Pollution, Causes and Cures.

Science.gov (United States)

Manufacturing Chemists Association, Washington, DC.

This commentary on sources of water pollution and water pollution treatment systems is accompanied by graphic illustrations. Sources of pollution such as lake bottom vegetation, synthetic organic pollutants, heat pollution, radioactive substance pollution, and human and industrial waste products are discussed. Several types of water purification…

Speciation of Pb in industrially polluted soils

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Ottosen, Lisbeth M.; Pedersen, Anne Juul

2006-01-01

This study was aimed at elucidating the importance of original Pb-speciation versus soil-characteristics to mobility and distribution of Pb in industrially polluted soils. Ten industrially polluted Danish surface soils were characterized and Pb speciation was evaluated through SEM-EDX studies...

Dust and smoke pollution monitoring in industrial unit

International Nuclear Information System (INIS)

Shamsi, S.S.

1995-01-01

Dust and smoke are the two most commonly emitted industrial pollutants which are visible to the naked eye. Cement plants and power generation plants, based on coal and fuel oil etc. are the most common examples of industry emitting these pollutants. In this article these pollutants have been briefly described and some monitoring instruments for dust and smoke emissions have been specific. These instruments are especially suitable for power station and the cement industry etc. Automotive in urban areas. However, this paper does not include equipment for automotive exhaust pollution. (author)

Trends in U.S.A. on environmental assessment of the common industrial wastes

International Nuclear Information System (INIS)

Yamauchi, Kiyoshi

1994-01-01

In Japan, the waste materials are divided to two parts of radioactive wastes and common wastes according to the law on treatment and cleaning of the wastes, and the latter is divided further to two parts of life type wastes and business type wastes. Among them, a part of wastes called the industrial wastes in the business wastes causes some troubles. In Japan, maintenance of approval level of the wastes treatment was conducted by selection of treating method due to feature of the wastes, selection of treating matters due to the treating site and method, and environmental assessment of each treatment project program. However, in U.S.A., regulation on environmental impact due to various human actions has been executed since 1960, and environmental assessment is controlled by a law. And, regulations on the wastes, the treating facilities and the formed pollution were also determined by laws. Furthermore, technical field of the environmental assessment is already executed in U.S.A. but some parts are not in Japan. On the evaluation method, there are some differences between in U.S.A. and in Japan, but are some common points in technical informations, estimating methods and so on, where future technical cooperations and movements between them in environmental assessment on both common industrial wastes and high level radioactive wastes. (G.K.)

Industrial wastes of the cities of Baku and Sumgait and their effect on green plantings

Energy Technology Data Exchange (ETDEWEB)

Amirov, R O; Ismaylov, A R

1969-01-01

Baku and Sumgait had large oil production and chemical industries. Investigations showed that injury in green planting depended essentially on the nature of the waste products. Air polluted with SO/sub 2/, chlorine, and fluorine compounds produced dark brown bumps on the leaves. As the distance from the industries increased, the frequency and the intensity of the injuries decreased. Some of the ornamental species were beter adjusted and had a greater resistance. The establishment and development of green plantings were important for combating air pollution and for the sanitary well-being of the industrial area. Plans of landscaping of industrial enterprises included green plantings directly on the territory of the enterprises as well as in areas surrounding them in a radius of 150-500 m. Green shelter belts were needed for protection of the strong northern winds. The selection of plants was made considering their gas resistance, their drought resistance, as well as the plants' ability to grow in solonchak-solonets, clayey, and clayey loam soils characteristic for the Apsheron Peninsula. Trees and bushes were planted by the trench method. Irrigation with waste water was avoided.

Biomonitoring of genotoxicity of industrial fertilizer pollutants in Aiolopus thalassinus (Orthoptera: Acrididae) using alkaline comet assay.

Science.gov (United States)

Abdelfattah, Eman A; Augustyniak, Maria; Yousef, Hesham A

2017-09-01

Phosphate fertilizer industry is considered as one of the main sources of environmental pollutants. Besides solid waste products, e.g. phosphates, sulphates, and heavy metals, also atmospheric pollutants, such as hydrofluoric acid fumes (HF), sulphur dioxide (SO 2 ), nitrogen oxides (NO 2 ), and particulate matter with diameter up to 10 μm (PM 10 ) can be dangerous. Genotoxic effect of these pollutants was monitored by assessing the DNA damage using alkaline comet assay on cells from brain, thoracic muscles and gut of Aiolopus thalassinus collected at three sites (A-C) located at 1, 3, and 6 km away from Abu-Zaabal Company for Fertilizers and Chemical Industries. Control site was established 32 km from the source of pollution, at the Cairo University Campus. The level of the DNA damage was significantly higher in insects from polluted sites comparing to that from the control site. A strong negative correlation between percentage of cells with visible DNA damage (% of severed cells) and the distance of the sites from Abu-Zaabal Company was found. The best parameter for monitoring of fertilizer pollutants is % of severed cells. Possible impact of Abu-Zaabal Company (extremely high concentration of phosphates and sulphates in all the polluted sites) on DNA integrity in A. thalassinus tissues was discussed. The potential use of the comet assay as a biomonitoring method of the environmental pollution caused by fertilizer industry was proposed. Specific pollution resulting from the activity of the fertilizer industry can cause comparable adverse effects in the organisms inhabiting areas up to 6 km from the source of contamination. Copyright © 2017 Elsevier Ltd. All rights reserved.

Utilization of byproducts and waste materials from meat, poultry and fish processing industries: a review.

Science.gov (United States)

Jayathilakan, K; Sultana, Khudsia; Radhakrishna, K; Bawa, A S

2012-06-01

India is bestowed with vast livestock wealth and it is growing at the rate of 6% per annum. The contribution of livestock industry including poultry and fish is increasing substantially in GDP of country which accounts for >40% of total agricultural sector and >12% of GDP. This contribution would have been much greater had the animal by-products been also efficiently utilized. Efficient utilization of by-products has direct impact on the economy and environmental pollution of the country. Non-utilization or under utilization of by-products not only lead to loss of potential revenues but also lead to the added and increasing cost of disposal of these products. Non-utilization of animal by-products in a proper way may create major aesthetic and catastrophic health problems. Besides pollution and hazard aspects, in many cases meat, poultry and fish processing wastes have a potential for recycling raw materials or for conversion into useful products of higher value. Traditions, culture and religion are often important when a meat by-product is being utilized for food. Regulatory requirements are also important because many countries restrict the use of meat by-products for reasons of food safety and quality. By-products such as blood, liver, lung, kidney, brains, spleen and tripe has good nutritive value. Medicinal and pharmaceutical uses of by-product are also highlighted in this review. Waste products from the poultry processing and egg production industries must be efficiently dealt with as the growth of these industries depends largely on waste management. Treated fish waste has found many applications among with which the most important are animal feed, biodiesel/biogas, dietectic products (chitosan), natural pigments (after extraction) and cosmetics (collagen). Available information pertaining to the utilization of by-products and waste materials from meat, poultry and fish and their processing industries has been reviewed here.

Ecotoxicity of waste water from industrial fires fighting

Science.gov (United States)

Dobes, P.; Danihelka, P.; Janickova, S.; Marek, J.; Bernatikova, S.; Suchankova, J.; Baudisova, B.; Sikorova, L.; Soldan, P.

2012-04-01

As shown at several case studies, waste waters from extinguishing of industrial fires involving hazardous chemicals could be serious threat primary for surrounding environmental compartments (e.g. surface water, underground water, soil) and secondary for human beings, animals and plants. The negative impacts of the fire waters on the environment attracted public attention since the chemical accident in the Sandoz (Schweizerhalle) in November 1986 and this process continues. Last October, special Seminary on this topic has been organized by UNECE in Bonn. Mode of interaction of fire waters with the environment and potential transport mechanisms are still discussed. However, in many cases waste water polluted by extinguishing foam (always with high COD values), flammable or toxic dangerous substances as heavy metals, pesticides or POPs, are released to surface water or soil without proper decontamination, which can lead to environmental accident. For better understanding of this type of hazard and better coordination of firemen brigades and other responders, the ecotoxicity of such type of waste water should be evaluated in both laboratory tests and in water samples collected during real cases of industrial fires. Case studies, theoretical analysis of problem and toxicity tests on laboratory model samples (e.g. on bacteria, mustard seeds, daphnia and fishes) will provide additional necessary information. Preliminary analysis of waters from industrial fires (polymer material storage and galvanic plating facility) in the Czech Republic has already confirmed high toxicity. In first case the toxicity may be attributed to decomposition of burned material and extinguishing foams, in the latter case it can be related to cyanides in original electroplating baths. On the beginning of the year 2012, two years R&D project focused on reduction of extinguish waste water risk for the environment, was approved by Technology Agency of the Czech Republic.

Speciation imperatives for waste management and environmental pollution

International Nuclear Information System (INIS)

Wymer, R.G.

2001-01-01

This paper addresses speciation requirements in the context of problems produced by nuclear energy and nuclear weapons production. These problems are primarily in the areas of waste management, material contamination, and environmental pollution. They pose difficult and important measurement and speciation challenges. Examples of speciation requirements in the context of national and international regulations are presented to exemplify and make quantitative the types of problems posed by waste management, material contamination, and environmental pollution. The importance of identifying species present in the natural environment as well as in wastes from chemical and physical processing and from waste management activities and accidental releases is addressed. Differing speciation requirements for macro and micro concentrations of species are discussed. The role of speciation in modelling studies is discussed. (author)

Environmental Restoration Contractor Waste Minimization and Pollution Prevention Plan. Revision 1

International Nuclear Information System (INIS)

Lewis, R.A.

1996-03-01

This plan contains the Environmental Restoration Contractor (ERC) Waste Minimization and Pollution Prevention (WMin/P2) Program. The plan outlines the activities and schedules developed by the ERC to reduce the quantity and toxicity of waste dispositioned as a result of restoration and remediation activities. This plan satisfies US Department of Energy (DOE) requirements including the Pollution Prevention Awareness program required by DOE Order 5400.1 (DOE 1988). This plan is consistent with Executive Order 12856 and Secretary O'Leary's pollution prevention Policy Statement of December 27, 1994, which set US and DOE pollution prevention policies, respectively. It is also consistent with the DOE Pollution Prevention Crosscut Plan, 1994, which provides guidance in meeting the DOE goals in pollution prevention. The purpose of this plan is to aid ERC projects in meeting and documenting compliance with requirements for WMin/P2. This plan contains the objectives, strategy, and support activities of the ERC Team WMin/P2 program. The basic elements of the plan are pollution prevention goals, waste assessments of major waste streams, implementation of feasible waste minimization opportunities, and a process for reporting achievements. Wherever appropriate, the ERC will integrate the pollution prevention activities in this plan into regular program activities rather than establishing separate WMin/P2 activities. Moreover, wherever possible, existing documents, procedures, and activities will be used to meet WMin/P2 requirements

ESTIMATION OF INDUSTRIAL WASTE SAFETY BY THE “CHEMICAL OXYGEN DEMAND” INDEX

Directory of Open Access Journals (Sweden)

A. S. Kayshev

2015-01-01

Full Text Available One of the indices of industrial waste safety including distillers grains is chemical oxygen demand (COD, and its value (53591÷64184 mg O/dm3 shows that it can be considered as unsustainable waste. This high value of COD is conditioned by the absence of toxins in distillers grains, and by concentration of biologically active substances after which isolation the distillers grains index lowers by 74%. This allows considering the distillers grains as environmentally safe. The results received evidence the necessity for consideration of COD index only as an index of oxidized substances, but not the criteria of waste pollution.

Pollution and health risk assessment of industrial and residential area based on metal and metalloids contents in soil and sediment samples from and around the petrochemical industry, Serbia

Science.gov (United States)

Relic, Dubravka; Sakan, Sanja; Andjelkovic, Ivan; Djordjevic, Dragana

2017-04-01

Within this study the investigation of pollution state of metal and metalloids contamination in soils and sediments samples of the petrochemical and nearby residential area is present. The pseudo-total concentrations of Ba, Cd, Co, Cu, Cr, Mn, Ni, Pb, V, Zn, As, Hg, and Se were monitored with ICP/OES. The pollution indices applied in this work, such as the enrichment factor, the pollution load index, the total enrichment factor, and the ecological risk index showed that some of the soil and sediment samples were highly polluted by Hg, Ba, Pb, Cd, Cr Cu and Zn. The highest pollution indices were calculated for Hg in samples from the petrochemical area: chloralkali plant, electrolysis factory, mercury disposal area, and in samples from the waste channel. The pollution indices of the samples from the residential area indicated that this area is not polluted by investigated elements. Besides the pollution indices, the metal and metalloids concentrations were used in the equations for calculating the health risk criteria. We calculate no carcinogenic and carcinogenic risks for the composite worker and residential people by usage adequate equations. In analyzed samples, the no carcinogenic risks were lower than 1. The highest values of carcinogenic risk were obtained in sediment samples from the waste channel within the petrochemical industry and the metal that mostly contributes to the highest carcinogenic risk is Cr. Correlation analysis of pollution indices and carcinogenic risks calculated from the residential area samples showed good correlations while this is not the case for an industrial area.

Does industrial waste taxation contribute to reduction of landfilled waste? Dynamic panel analysis considering industrial waste category in Japan.

Science.gov (United States)

Sasao, Toshiaki

2014-11-01

Waste taxes, such as landfill and incineration taxes, have emerged as a popular option in developed countries to promote the 3Rs (reduce, reuse, and recycle). However, few studies have examined the effectiveness of waste taxes. In addition, quite a few studies have considered both dynamic relationships among dependent variables and unobserved individual heterogeneity among the jurisdictions. If dependent variables are persistent, omitted variables cause a bias, or common characteristics exist across the jurisdictions that have introduced waste taxes, the standard fixed effects model may lead to biased estimation results and misunderstood causal relationships. In addition, most existing studies have examined waste in terms of total amounts rather than by categories. Even if significant reductions in total waste amounts are not observed, some reduction within each category may, nevertheless, become evident. Therefore, this study analyzes the effects of industrial waste taxation on quantities of waste in landfill in Japan by applying the bias-corrected least-squares dummy variable (LSDVC) estimators; the general method of moments (difference GMM); and the system GMM. In addition, the study investigates effect differences attributable to industrial waste categories and taxation types. This paper shows that industrial waste taxes in Japan have minimal, significant effects on the reduction of final disposal amounts thus far, considering dynamic relationships and waste categories. Copyright © 2014 Elsevier Ltd. All rights reserved.

Burden of industrial waste and potential for recycling: technological, economic and environmental aspects

Directory of Open Access Journals (Sweden)

Mihajlović Ivan

2017-07-01

Full Text Available Many benefits resulting from the development of the heavy industry are, unfortunately, accompanied by many issues resulting from the process of generating the industrial waste. This manuscript is presenting the environmental consequences, resulting from long period of time of heavy industry production and exploring the possibilities to recycle some of the industrial waste generated during the period of more than one century of ore excavation and copper extraction in the region of Eastern Serbia, in the vicinity of city of Bor. First part of the manuscript is presenting the scope of environmental issues, resulting from the heavy industry in this region and the amounts and the structure of the industrial waste, generated in this area, as well as the influence of generated waste to the environment of the region. Second part of the manuscript is dealing with the potential to recycle and reuse some of this waste, analyzing technological, economic and environmental aspects at the same time. In the final segment of the paper, some practical examples will be addressed based on the research work conducted at both experimental and industrial level. Results presented in the manuscript are mostly collected during long term research of the project team from Technical faculty in Bor, University of Belgrade, in the field of environmental management. This way, this manuscript is based on review of the research papers authored or co-authored by the author of this work, dealing with water, soil and air pollution, published in leading international journals. Also, the manuscript is presenting the literature review of other international issues dealing with the environmental management issues in the vicinity of large industrial complexes. Parts of the research results, presented in this manuscript are financially supported by the Ministry of Education, Science and Technological development of Republic of Serbia, under the project TR34023.

Waste minimization and pollution prevention awareness plan. Revision 1

International Nuclear Information System (INIS)

1994-07-01

The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Waste Minimization and Pollution Prevention Awareness Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, estimate budgets, and review the plan. In addition to the above, this plan records LLNL's goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities

Real Time Monitoring System of Pollution Waste on Musi River Using Support Vector Machine (SVM) Method

Science.gov (United States)

Fachrurrozi, Muhammad; Saparudin; Erwin

2017-04-01

Real-time Monitoring and early detection system which measures the quality standard of waste in Musi River, Palembang, Indonesia is a system for determining air and water pollution level. This system was designed in order to create an integrated monitoring system and provide real time information that can be read. It is designed to measure acidity and water turbidity polluted by industrial waste, as well as to show and provide conditional data integrated in one system. This system consists of inputting and processing the data, and giving output based on processed data. Turbidity, substances, and pH sensor is used as a detector that produce analog electrical direct current voltage (DC). Early detection system works by determining the value of the ammonia threshold, acidity, and turbidity level of water in Musi River. The results is then presented based on the level group pollution by the Support Vector Machine classification method.

Reducing Marine and Coastal Pollution

OpenAIRE

World Bank Group

2016-01-01

The West African coastline is home to major industries, mining activities, peri-urban and agro-industry, and tourism, as well as urban and seaside residences, all of which generate waste and cause pollution. Many areas along the coast also lack adequate wastewater and solid waste management systems. As a result, large volumes of untreated wastewater and solid waste are dumped into the open...

Potential pollution prevention and waste minimization for Department of Energy operations

International Nuclear Information System (INIS)

Griffin, J.; Ischay, C.; Kennicott, M.; Pemberton, S.; Tull, D.

1995-10-01

With the tightening of budgets and limited resources, it is important to ensure operations are carried out in a cost-effective and productive manner. Implementing an effective Pollution Prevention strategy can help to reduce the costs of waste management and prevent harmful releases to the environment. This document provides an estimate of the Department of Energy's waste reduction potential from the implementation of Pollution Prevention opportunities. A team of Waste Minimization and Pollution Prevention professionals was formed to collect the data and make the estimates. The report includes a list of specific reduction opportunities for various waste generating operations and waste types. A generic set of recommendations to achieve these reduction opportunities is also provided as well as a general discussion of the approach and assumptions made for each waste generating operation

Recent developments in the DOE Waste Minimization Pollution Prevention Program

International Nuclear Information System (INIS)

Hancock, J.K.

1993-01-01

The U.S. Department of Energy (DOE) is involved in a wide variety of research and development, remediation, and production activities at more than 100 sites throughout the United States. The wastes generated cover a diverse spectrum of sanitary, hazardous, and radioactive waste streams, including typical office environments, power generation facilities, laboratories, remediation sites, production facilities, and defense facilities. The DOE's initial waste minimization activities pre-date the Pollution Prevention Act of 1990 and focused on the defense program. Little emphasis was placed on nonproduction activities. In 1991 the Office of Waste Management Operations developed the Waste Minimization Division with the intention of coordinating and expanding the waste minimization pollution prevention approach to the entire complex. The diverse nature of DOE activities has led to several unique problems in addressing the needs of waste minimization and pollution prevention. The first problem is developing a program that addresses the geographical and institutional hurdles that exist; the second is developing a monitoring and reporting mechanism that one can use to assess the overall performance of the program

EXOPOLYSACCHARIDES SYNTHESIS ON INDUSTRIAL WASTES

Directory of Open Access Journals (Sweden)

T.P.

2016-04-01

Full Text Available Data from the literature and our own studies on the synthesis of microbial exopolysaccharides on various industrial waste (food industry, agricultural sector, biodiesel production, etc. are reviewed here. Utilization of industrial waste to obtain exopolysaccharides will solve not only the problem of secondary raw materials accumulation, but also will reduce the costs of the biosynthesis of practically valuable metabolites. In addition, some kinds of waste have a number of advantages compared to traditional carbohydrate substrates: aside from environmental health benefits, there are technological ones, like the presence of growth factors. There is also no need to use anti-foam substances and substrate sterilization in the latter case.

Hanford Site waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

1994-05-01

The Hanford Site WMin/P2 program is an organized, comprehensive, and continual effort to systematically reduce the quantity and toxicity of hazardous, radioactive, mixed, and sanitary wastes; conserve resources; and prevent or minimize pollutant releases to all environmental media from all Site activities. The Hanford Site WMin/P2 program plan reflects national and DOE waste minimization and pollution prevention goals and policies, and represents an ongoing effort to make WMin/P2 part of the Site operating philosophy. In accordance with these policies, a hierarchical approach to environmental management has been adopted and is applied to all types of polluting and waste generating activities. Pollution prevention and waste minimization through source reduction are first priority in the Hanford WMin/P2 program, followed by environmentally safe recycling. Treatment to reduce the quantity, toxicity, and/or mobility will be considered only when prevention or recycling are not possible or practical. Environmentally safe disposal is the last option

ASSESSMENT OF TOXICITY OF INDUSTRIAL WASTES USING CROP PLANT ASSAYS

Directory of Open Access Journals (Sweden)

Carmen Alice Teacă

2008-11-01

Full Text Available Environmental pollution has a harmful action on bioresources, including agricultural crops. It is generated through many industrial activities such as mining, coal burning, chemical technology, cement production, pulp and paper industry, etc. The toxicity of different industrial wastes and heavy metals excess was evaluated using crop plant assays (germination and hydroponics seedlings growth tests. Experimental data regarding the germination process of wheat (from two cultivars and rye seeds in the presence of industrial wastes (thermal power station ash, effluents from a pre-bleaching stage performed on a Kraft cellulose – chlorinated lignin products or chlorolignin, along with use of an excess of some heavy metals (Zn and Cu are presented here. Relative seed germination, relative root elongation, and germination index (a factor of relative seed germination and relative root elongation were determined. Relative root elongation and germination index were more sensitive indicators of toxicity than seed germination. The toxic effects were also evaluated in hydroponics experiments, the sensitivity of three crop plant species, namely Triticum aestivum L. (wheat, Secale cereale (rye, and Zea mays (corn being compared. Physiological aspects, evidenced both by visual observation and biometric measurements (mean root, aerial part and plant length, as well as the cellulose and lignin content were examined.

Regulatory barriers to pollution prevention: A position paper of the implementation council of the American institute for pollution prevention

International Nuclear Information System (INIS)

Byers, R.L.

1991-01-01

Pollution prevention/waste minimization is a win-win-win situation for government, industry, and the public, which offers more than just protection of the environment for all. Industry gains from reduced capital and operating costs, reduced liabilities, cleaner and safer working conditions, conservation of energy and material resources, and the opportunity for government and industry to work together in a cooperative manner. However, a number of regulatory barriers exist which discourage pollution prevention/waste minimization. This paper provides examples for the aluminum, chemical, petroleum, and wood treating industries of how these regulatory barriers become disincentives. To promote pollusion prevention/waste minimization, Congress and the US EPA need to reexamine those RCRA provisions which support a command and control strategy that creates the barriers. The barriers include the distinction between value and valueless materials, offsite storage requirements prior to reuse/recycle, the Derived from Rule, the Burning for Fuel Rule, land ban technology standards, and RD and D restrictions. A new RCRA Pollution Prevention/Waste Minimization subtitle is proposed to eliminate or minimize these barriers

Waste Minimization and Pollution Prevention Awareness Plan

International Nuclear Information System (INIS)

1994-04-01

The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, to estimate budget, and to review the plan. In addition to the above, this plan records LLNL's goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities

Annual report of waste generation and pollution prevention progress, 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

This Report summarizes the waste generation and pollution prevention activities of the major operational sites in the Department of Energy (DOE). We are witnessing progress in waste reduction from routine operations that are the focus of Department-wide reduction goals set by the Secretary on May 3,1996. The goals require that by the end of 1999, we reduce, recycle, reuse, and otherwise avoid waste generation to achieve a 50 percent reduction over 1993 levels. This Report provides the first measure of our progress in waste reduction and recycling against our 1993 waste generation baseline. While we see progress in reducing waste from our normal operations, we must begin to focus attention on waste generated by cleanup and facilities stabilization activities that are the major functions of the Office of Environmental Management. Reducing the generation of waste is one of the seven principles that I have established for the Office of Environmental Management Ten Year Plan. As part of our vision to complete a major portion of the environmental cleanup at DOE sites over the next ten years, we must utilize the potential of the pollution prevention program to reduce the cost of our cleanup program. We have included the Secretarial goals as part of the performance measures for the Ten Year Plan, and we are committed to implementing pollution prevention ideas. Through the efforts of both Federal and contractor employees, our pollution prevention program has reduced waste and the cost of our operations. I applaud their efforts and look forward to reporting further waste reduction progress in the next annual update of this Report.

Annual report of waste generation and pollution prevention progress, 1994

International Nuclear Information System (INIS)

1996-09-01

This Report summarizes the waste generation and pollution prevention activities of the major operational sites in the Department of Energy (DOE). We are witnessing progress in waste reduction from routine operations that are the focus of Department-wide reduction goals set by the Secretary on May 3,1996. The goals require that by the end of 1999, we reduce, recycle, reuse, and otherwise avoid waste generation to achieve a 50 percent reduction over 1993 levels. This Report provides the first measure of our progress in waste reduction and recycling against our 1993 waste generation baseline. While we see progress in reducing waste from our normal operations, we must begin to focus attention on waste generated by cleanup and facilities stabilization activities that are the major functions of the Office of Environmental Management. Reducing the generation of waste is one of the seven principles that I have established for the Office of Environmental Management Ten Year Plan. As part of our vision to complete a major portion of the environmental cleanup at DOE sites over the next ten years, we must utilize the potential of the pollution prevention program to reduce the cost of our cleanup program. We have included the Secretarial goals as part of the performance measures for the Ten Year Plan, and we are committed to implementing pollution prevention ideas. Through the efforts of both Federal and contractor employees, our pollution prevention program has reduced waste and the cost of our operations. I applaud their efforts and look forward to reporting further waste reduction progress in the next annual update of this Report

Genotoxicity monitoring of industrial wastes using plant bioassays and management through vermitechnology: A review

Directory of Open Access Journals (Sweden)

Sartaj Ahmad Bhat

2017-10-01

Full Text Available The main objective of this review was to summarize and present a comprehensive account of the cytotoxic, genotoxic and mutagenic potential of various industrial wastes/sludges using some well-known plant bioassays followed by their bioremediation using vermitechnology. Industries are the main origin of discharges of various types of chemical wastes and are the main causes of environmental degradation. The direct application of industrial sludges could also harm the local biota. The genotoxicity of industrial sludges is assessed using various plant bioassays (for example Allium cepa, Vicia faba and these bioassays are comparatively more sensitive and cost-effective compared to other in-vitro genotoxicity bioassays. In addition, the materials used for toxicity evaluation are easily available and are being routinely used for the monitoring of environmental pollution. In most studies, the increases in root length and mitotic index, as well as the decrease in chromosomal aberrations in post vermicomposted sludges/wastes indicate that earthworms have the ability to reduce the ecotoxicogenetic effects of sludges/wastes. Post vermicompost is considered an excellent material of a homogenous nature as it has reduced levels of contaminants and holds more nutrients over a longer time without affecting the environment. The biotransformation potential of earthworms and their ability to detoxify most of the heavy metals in industrial sludges is because of their strong metabolic system and the involvement of diverse intestinal microflora and chloragocytic cells that reduce toxic forms to nontoxic forms. This unique ability of earthworms confirms the effectiveness of vermitechnology in reducing the toxicity of industrial wastes. Keywords: Allium cepa, Earthworm, Industrial sludge, Toxicity, Vermicomposting

PENGOLAHAN LIMBAH CAIR INDUSTRI SUSU (Liquid Waste Management in Milk Factory

Directory of Open Access Journals (Sweden)

Wagini Wagini

2002-03-01

Full Text Available ABSTRAK Telah dilakukan suatu penelitian untuk mengetahui kondisi limbah cair industri susu. hasil penelitian menunjukkan bahwa limbah cair industri susu mengandung zat-zat pencemar dalam tingkat yang membahayakan lingkungan, sehingga limbah cair tersebut perlu didaur ulang. Untuk itu diperlukan suatu instalasi peralatan yang mampu mengolah limbah tersebut. Pada penelitian ini proses pengolahan dilakukan dengan mengkombinasikan proses-proses pengolahan secara Fisika, Kimia dan Biologi. Dengan tahapan proses pengolahan yang dipilih meliputi; Proses equalisasi, proses anaerob, proses aerasi, lumpur aktif, proses sedimentasi, proses koagulasi-flokulasi, proses sedimentasi, proses flotasi, proses pengendapan partikel ringan, proses penyaringan dengan pasir dan arang aktif.    Kualitas air hasil pengolahan dianalisa secara Fisika, Kimia dan Biologi melalui parameter-parameter: suhu, kekeruhan, zat padat tersuspensi, zat padat terlarut, daya hantar listrik, PH, BOD, COD dan jumlah bakteri. Penelitian ini menunjukkan air hasil pengolahan aman untuk dibuang ke lingkungan.   ABSTRACT A research to identify the condition of milk industry liquid waste was conducted. The result showed that the waste contained pollutants at the level the endangered the environment. Therefore, the waste had to be recycled in which a liquid waste treatment installation is needed. In this research, the process of milk industry liquid waste was done by combining processing techniques of physics, chemistry and biology. The processing steps include the processes of equalization, anaerobe, aeration, sedimentation, coagulation-flocculation, sedimentation, flotation, sedimentation, filtering with sand and activated carbon. The water resulted from the processes was analyzed in terms of physical, chemical and biological characteristics e.g. temperature, turbidity, suspended solid, solutes solid, conductivity, pH, BOD, COD and amount of bacteria. This research, shows that the water

Environmental Pollution: Sanitary Engineering and Industrial Waste.

Science.gov (United States)

1977-07-01

and closed ecological systems which may prove beneficial to ongoing research and operations for controlling environmental pollution . Corporate Author-Monitoring Agency, Subject, Title and Personal Author are provided. (Author)

Beneficiary role of grapes residue, an organic waste of agro-based industry causing environmental pollution - a new concept of crop production in hydroponics

International Nuclear Information System (INIS)

Butt, S.J.; Varis, S.

2005-01-01

The world is facing a serious threat of environmental pollution as a result of which our soils, air and water are becoming highly contaminated with the passage of time. Many epidemics have engulfed a number of countries in various diseases causing the loss of hundreds of thousands of human lives. The wastes of agro-based industries are mostly organic in nature, and if not properly handled, usually become nuisance and also the source of food for pathogens and other harmful microorganisms thus the surrounding becomes polluted. It has been reported that grapes residue (also called grapes marc or pressed grapes) was a serious environmental problem Tekirdag city of Turkey. This waste material was thrown out of the factory (Tekil Fabrikasi) after the extraction of grape juices used for different products. With dual objective, a plan was made to remove the waste material from polluted area subsequently managed to use it a source of soilless growing medium for the production horticultural crops through hydroponics system in the unheated greenhouse. The use of grapes residue for crop production is rare and hardly documented in the literature thus the idea is innovative in its nature that may lead to open the vista of new avenues. A trial of bag culture was conducted to evaluate the possibilities of use of grapes marc as a pure growing substrate for the production of lettuce and tomato crops. Quite encouraging results of a number of parameters of both the crops appeared against the soil-mixture (control). The studied characteristics were relating to vegetative, reproductive, yield physical and chemical performances and sensory traits. It is predicted that grapes marc possesses a great potential of organic rooting medium for growth and development of commercial crops, provided the climatic, nutritional and management activities scheduled in view of the kind and nature of crop cultivar to be grown under unheated glass house conditions. (author)

Waste management, informal recycling, environmental pollution and public health.

Science.gov (United States)

Yang, Hong; Ma, Mingguo; Thompson, Julian R; Flower, Roger J

2018-03-01

With rapid population growth, especially in low-income and middle-income countries, the generation of waste is increasing at an unprecedented rate. For example, annual global waste arising from waste electrical and electronic equipment alone will have increased from 33.8 to 49.8 million tonnes between 2010 and 2018. Despite incineration and other waste treatment techniques, landfill still dominates waste disposal in low-income and middle-income countries. There is usually insufficient funding for adequate waste management in these countries and uptake of more advanced waste treatment technologies is poor. Without proper management, many landfills represent serious hazards as typified by the landslide in Shenzhen, China on 20 December 2015. In addition to formal waste recycling systems, approximately 15million people around the world are involved in informal waste recycling, mainly for plastics, metals, glass and paper. This review examines emerging public health challenges, in particular within low-income and middle-income countries, associated with the informal sector. While informal recyclers contribute to waste recycling and reuse, the relatively primitive techniques they employ, combined with improper management of secondary pollutants, exacerbate environmental pollution of air, soil and water. Even worse, insufficient occupational health measures expose informal waste workers to a range of pollutants, injuries, respiratory and dermatological problems, infections and other serious health issues that contribute to low life expectancy. Integration of the informal sector with its formal counterparts could improve waste management while addressing these serious health and livelihood issues. Progress in this direction has already been made notably in several Latin American countries where integrating the informal and formal sectors has had a positive influence on both waste management and poverty alleviation. © Article author(s) (or their employer(s) unless

POSSIBILITIES FOR WASTE WATER UTITLIZATION FROM CANNING INDUSTRY

Directory of Open Access Journals (Sweden)

A. Kraevska

2014-03-01

Full Text Available Waste waters from the different processing sectors (branch, activities of the canning factories was investigated. It was established that the greatest organic pollution is a result of the production of frozen half-fried potatoes. The possibilities of reducing of the organic pollution by cultivating fungi of the genus Aspergillus and Trichoderma in the waste waters was studied.

Sustainable urban development and industrial pollution

Directory of Open Access Journals (Sweden)

Petrović Julka

2016-01-01

Full Text Available Sustainable development of cities is highly connected with the pollution generated from industrial facilities and power plants. Both affect quality of air, weather, health and quality of life. The main goal of this paper is to determine the impact of selected weather parameters on the pollution from mentioned plants. From the research results, it can be concluded that sustainable urban development and welfare of citizens are dependent on causal relationship between pollution and weather. The greatest level of impact was recorded for nitric dioxide. In the case of carbon monoxide, the level of impact is the middle. The lowest level was recorded for particulate matter. The biggest impact on the carbon monoxide emission and particulate matter is that of air pressure, whereas temperature has the biggest impact on nitrogen dioxide emission. The research shows that air humidity and wind speed do not have a significant impact on the emission of pollutants from the plants. Research shows need for further studies in the field of impact of pollution from industry on urban weather and human health.

Effect of industrial pollution on seed germination

Energy Technology Data Exchange (ETDEWEB)

Iqbal, M.Z.; Qadir, S.A.

1973-01-01

The germination behavior of seeds in polluted waters and polluted soil extracts was found to be identical, only a few species behaved differently. Prosopis juliflora, Haloxylon recurvum, Acacia senegal showed best germination in the two conditions but Prosopis juliflora was the most resistant to pollution. In Suaeda fruticosa no germination took place in the control treatment whereas highest germination (70%) was seen in treatment with polluted soil extract of EPLA. Blepharis sindica showed a stimulating effect of polluted water on germination, whereas low germination was observed when their seeds were treated with the soil extract of the same site. 40% germination of Suaeda monoica was seen in polluted water of Carbon and Ribbon Mfg. Co., whereas 30% germination was found in a control treatment. Low percentage of germination was found when the seeds of Cassia holosericea were treated with polluted waters of different industries as compared to soil extract treatments of the same industries. Datura alba showed 50, 30 and 10% seed germination in polluted soil extract of Carbon and Ribbon Mfg. Co., in control and in polluted water of Darbar Soap Works, respectively. 5 references, 1 table.

Westinghouse Hanford Company waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Craig, P.A.; Nichols, D.H.; Lindsey, D.W.

1991-08-01

The purpose of this plan is to establish the Westinghouse Hanford Company's Waste Minimization Program. The plan specifies activities and methods that will be employed to reduce the quantity and toxicity of waste generated at Westinghouse Hanford Company (Westinghouse Hanford). It is designed to satisfy the US Department of Energy (DOE) and other legal requirements that are discussed in Subsection C of the section. The Pollution Prevention Awareness Program is included with the Waste Minimization Program as permitted by DOE Order 5400.1 (DOE 1988a). This plan is based on the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, which directs DOE Field Office, Richland contractors to develop and maintain a waste minimization program. This waste minimization program is an organized, comprehensive, and continual effort to systematically reduce waste generation. The Westinghouse Hanford Waste Minimization Program is designed to prevent or minimize pollutant releases to all environmental media from all aspects of Westinghouse Hanford operations and offers increased protection of public health and the environment. 14 refs., 2 figs., 1 tab

Waste Material Management: Energy and materials for industry

Energy Technology Data Exchange (ETDEWEB)

1993-05-01

This booklet describes DOE`s Waste Material Management (WMM) programs, which are designed to help tap the potential of waste materials. Four programs are described in general terms: Industrial Waste Reduction, Waste Utilization and Conversion, Energy from Municipal Waste, and Solar Industrial Applications.

Monitoring of toxic elements present in sludge of industrial waste using CF-LIBS.

Science.gov (United States)

Kumar, Rohit; Rai, Awadhesh K; Alamelu, Devanathan; Aggarwal, Suresh K

2013-01-01

Industrial waste is one of the main causes of environmental pollution. Laser-induced breakdown spectroscopy (LIBS) was applied to detect the toxic metals in the sludge of industrial waste water. Sludge on filter paper was obtained after filtering the collected waste water samples from different sections of a water treatment plant situated in an industrial area of Kanpur City. The LIBS spectra of the sludge samples were recorded in the spectral range of 200 to 500 nm by focusing the laser light on sludge. Calibration-free laser-induced breakdown spectroscopy (CF-LIBS) technique was used for the quantitative measurement of toxic elements such as Cr and Pb present in the sample. We also used the traditional calibration curve approach to quantify these elements. The results obtained from CF-LIBS are in good agreement with the results from the calibration curve approach. Thus, our results demonstrate that CF-LIBS is an appropriate technique for quantitative analysis where reference/standard samples are not available to make the calibration curve. The results of the present experiment are alarming to the people living nearby areas of industrial activities, as the concentrations of toxic elements are quite high compared to the admissible limits of these substances.

Water Pollution Control Industry

Science.gov (United States)

Environmental Science and Technology, 1974

1974-01-01

A special report on the state of the water pollution control industry reveals that due to forthcoming federal requirements, sales and the backlogs should increase; problems may ensue because of shortages of materials and inflation. Included are reports from various individual companies. (MLB)

Assessment and analysis of industrial liquid waste and sludge disposal at unlined landfill sites in arid climate

International Nuclear Information System (INIS)

Al Yaqout, Anwar F.

2003-01-01

Municipal solid waste disposal sites in arid countries such as Kuwait receive various types of waste materials like sewage sludge, chemical waste and other debris. Large amounts of leachate are expected to be generated due to the improper disposal of industrial wastewater, sewage sludge and chemical wastes with municipal solid waste at landfill sites even though the rainwater is scarce. Almost 95% of all solid waste generated in Kuwait during the last 10 years was dumped in five unlined landfills. The sites accepting liquid waste consist of old sand quarries that do not follow any specific engineering guidelines. With the current practice, contamination of the ground water table is possible due to the close location of the water table beneath the bottom of the waste disposal sites. This study determined the percentage of industrial liquid waste and sludge of the total waste dumped at the landfill sites, analyzed the chemical characteristics of liquid waste stream and contaminated water at disposal sites, and finally evaluated the possible risk posed by the continuous dumping of such wastes at the unlined landfills. Statistical analysis has been performed on the disposal and characterization of industrial wastewater and sludge at five active landfill sites. The chemical analysis shows that all the industrial wastes and sludge have high concentrations of COD, suspended solids, and heavy metals. Results show that from 1993 to 2000, 5.14±1.13 million t of total wastes were disposed per year in all active landfill sites in Kuwait. The share of industrial liquid and sludge waste was 1.85±0.19 million t representing 37.22±6.85% of total waste disposed in all landfill sites. Such wastes contribute to landfill leachate which pollutes groundwater and may enter the food chain causing adverse health effects. Lined evaporation ponds are suggested as an economical and safe solution for industrial wastewater and sludge disposal in the arid climate of Kuwait

Pollution prevention and waste minimization opportunity assessment in environmental restoration

International Nuclear Information System (INIS)

Roybal, J.A.; Willison, C.P.

1997-01-01

The Environmental Restoration (ER) Project at Sandia National Laboratories implicitly subscribed to the philosophy of pollution prevention and waste minimization. As a result of a Department of Energy (DOE) offer, Pollution Prevention Opportunity Assessments (PPOA) were conducted at two ER sites and a decontamination and Demolition (D and D) site. The purpose of one of the PPOAs was to identify pollution prevention (P2) opportunities during environmental remediation at the Classified Waste Landfill located at Sandia National Laboratories, New Mexico (SNL/NM). The remediation activities at this site are scheduled to begin in the fall of 1997. The PPOA included presentations by the team members, a tour of the site, and a brainstorming session to list the waste streams, identify P2 opportunities and rank them in order of priority. Twenty-five P2 opportunities were identified during the brainstorming session of which twenty-two opportunities were selected for further investigation. Those twenty-two opportunities are discussed in this paper. A cost benefit analysis was performed for each P2 opportunity based on the estimated waste volume, feasibility, and cost. Pollution Prevention by Design (P2D) was incorporated into the PPOA to introduce waste minimization techniques that can be used during the planning phase of restoration projects

Pressures on industry to move to pollution prevention

International Nuclear Information System (INIS)

Poiasek, R.B.

1991-01-01

In a recent EPA report entitled Reducing Risk: Sorting Priorities and Strategies for Environmental Protection, a recommendation was made that EPA should emphasize pollution prevention as the preferred option for reducing risk. A significant number of states have adopted legislation requiring industry to conduct pollution prevention planning activities and submit reports to the state agencies. Federal legislation may be on the way. Industrial trade organizations are looking at the Chemical Manufacturing Association's Responsible Care: Program. Institutional investment groups are looking at initiatives like the Valdez Principles when selecting its portfolio, each of these initiatives have pollution prevention components. Environmentalists are demanding further attention be paid to pollution prevention. Industry is responding with a variety of programs designed to move them away from the classic end-of-the pipe controls which EPA mandated in previous regulations

An essay on: management of industrial waste, an engineer's viewpoint

International Nuclear Information System (INIS)

Raphael, M.A.

1995-01-01

Industrial waste and industrial waste management are described, with economic considerations and recommendations for an industrial waste management program applicable in Lebanon. Different conceptual systems for industrial waste management are presented: - The O effluent industrial plant, an electric manufacturing plant with mass and energy balance. - The industrial complexing concept where environmentally balanced and compatible, industries are located in one area. Waste effluents from one plant can be used as raw material for another plant. - A standard petroleum waste recovery plant to cope with local requirements complementary to the proposed sanitary waste treatment plant in Lebanon. Major sources of industrial waste in Lebanon are analyzed:local process industries, hospitals, laboratories, petroleum industries and power generation, are the major sources cited. For each source the level of treatment is indicated. Tables and appendixes on waste treatment and management along with the ISO 9000 series are presented. 10 refs. 3 figs

Hanford Site waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Place, B.G.

1998-01-01

This plan, which is required by US Department of Energy (DOE) Order 5400. 1, provides waste minimization and pollution prevention guidance for all Hanford Site contractors. The plan is primary in a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, Prime contractor implementation plans, and the Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation (DOE-RL, 1997a) describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994). Items discussed include the pollution prevention policy and regulatory background, organizational structure, the major objectives and goals of Hanford Site's pollution prevention program, and an itemized description of the Hanford Site pollution prevention program. The document also includes US Department of Energy, Richland Operations Office's (RL's) statement of policy on pollution prevention as well as a listing of regulatory drivers that require a pollution prevention program

Concept of Household Waste in Environmental Pollution Prevention Efforts

OpenAIRE

Sunarsih, Elvi

2014-01-01

Background : Waste is materials that are not used anymore which is the rest of human activities result including household, industrial, and mining. At a certain concentration, the presence of the waste can have a negative impact on the environment and on human health, so we need a proper handling for the waste. Household waste is waste from the kitchen, bathroom, laundry, house hold waste and industrial former human waste. Household waste that is over and it is not overcome is very potential ...

Logistic paradigm for industrial solid waste treatment processes

Directory of Open Access Journals (Sweden)

Janusz Grabara

2014-12-01

Full Text Available Due to the fact that industrial waste are a growing problem, both economic and environmental as their number is increasing every year, it is important to take measures to correctly dealing wi th industrial waste. This article presents the descriptive model of logistics processes concerning the management of industrial waste. In this model the flow of waste begins in the place of production and ends at their disposal. The article presents the concept of logistics model in graphical form together with an analysis of individual processes and their linkages, and opportunities to improve flow of industrial waste streams. Furthermore, the model allows for justification of the relevance of use logistics and its processes for waste management

Air Pollution Control and Waste Management

Science.gov (United States)

This special issue addresses air pollution control and waste management, two environmental problems that are usually considered separately. Indeed, one of the challenges of environmental protection is that problems are addressed in 'media-specific' ways. In reality, these problem...

A survey of hazardous and toxic wastes from lead and zinc industries in Zanjan province

International Nuclear Information System (INIS)

Khamesi, J.; Asadi, A.

2008-01-01

Angoran, situated in north-west of Zanjan province is unique in Middle East in respect of its rich reserves of Lead and Zinc minerals. These valuable reserves have attracted a number of Lead and Zinc industries into the province. With the absent of a proper waste management practices, a great deal of hazardous and toxic wastes are produced which contains a high percent of heavy metals that are potential sources for soil and water pollution. In this paper, after recognition of the main sources of the pollutants, the affected and vulnerable areas are mapped using Geographic Information System. The quality and quantity of these hazardous wastes are then evaluated by sampling and analyzing the samples and by taking into account the undesirable environmental conditions faced by the province, a number of preventive and curative measures for a better waste management practices are introduced. The annual wastes produced by 22 Zinc plants in the province are calculated to be about 260000 tons of filter cake leachates, 13000 tons of Cobalt filter cake, and 6550 tons of Cadmium-Nickel filter cakes. Two active Lead factories in the province are also producing about 13000 tons of slag annually. These wastes are containing 27000 ton Zinc, 9220 ton Lead, 560 ton Cadmium and 242000 tons of other wastes, that are left in open spaces within the factory or is dumped in dry riverbeds or near river valleys.The wastes are transported and deposited by wind in the environment and are washed by rain into the river systems or are soaked into the ground polluting the underground aquifers. Based of Basel Convention, these wastes are given international codes (Y 23, Y 31, Y 26, Y 46). Possession, disposal, and recycling of such wastes must be undertaken with specific management measures

Pollution control and resource reuse for alkaline hydrometallurgy of amphoteric metal hazardous wastes

CERN Document Server

Youcai, Zhao

2017-01-01

This book provides a comprehensive description of alkaline hydrometallurgy of amphoteric metal hazardous wastes. Topics focus on leaching of zinc and lead hazardous wastes, purification of leach solution of zinc and lead, electrowinning of zinc and lead from purified alkaline solutions, chemical reactions taking place in the production flowsheets, thermodynamic and spent electrolyte regeneration, alkaline hydrometallurgy of low-grade smithsonite ores, recovery of molybdenum and tungsten using ion flotation and solvent extraction processes and their application in chemical synthesis of Nb and Ta inorganic compounds, and industrial scale production of 1500-2000 t/a zinc powder using alkaline leaching–electrowinning processes. Processes described are cost-effective, generate lesser secondary pollutants, and have been applied widely in China. Readers that will find the book appealing include solid waste engineers, environmental managers, technicians, recycling coordinators, government officials, undergraduates ...

Glassceramics obtained from industrial waste

Energy Technology Data Exchange (ETDEWEB)

Cimdins, R.; Rozenstrauha, I.; Berzina, L. [Riga Technical University, Faculty of Chemical Technology, Biomaterials R and D Laboratory, 14/24 Azenes St., LV-1048 Riga (Latvia); Bossert, J.; Buecker, M. [Technisches Institut Materialwissenschaft, Friedrich-Schiller Universitaet, Loebdegraben 32, 07743 Jena (Germany)

2000-06-01

Large areas of Latvia are contaminated with industrial waste: metallurgical slag, fly-ash, etching refuse, peat, and coal ash as well as glass waste which often contain dangerous substances. From the environmental point of view this waste should be neutralised. As this waste also contains valuable chemical compounds, it can be considered as a raw material for the generation of new materials. One method of utilisation is to produce recycled materials - street plates, decorative tiles, or floor tiles. Dense sintered glassceramics with a water uptake of 0.34-3.23 wt.%, a final density of 2.93-3.05 g/cm{sup 3}, and a bending strength of 80-96 MPa have been created from industrial waste. The mast chemically durable glassceramics contained clay additions. Thus, the material containing only waste had a durability (mass loss) of 3.02% in 0.1 N HCl, while the composition containing 30% clay addition had a durability of 0.2% in 0.1 N HCl.

2016 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

International Nuclear Information System (INIS)

Cafferty, Kara Grace

2017-01-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (WRU-I-0160-01, Modification 1, formerly LA 000160 01), for the wastewater reuse site at the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2015, through October 31, 2016.

Quantitative and qualitative investigation of industrial solid waste in industrial plants located between Tehran and Karaj

Directory of Open Access Journals (Sweden)

M.R. Gohari

2011-07-01

Full Text Available Background and aims   Rapid population growth, industrial development, urbanization culture propagation and excessive material consumption are the most important factor which caused over increasing of municipal, industrial and agricultural waste in human society. Inappropriate disposal of generated waste in recent years created several environmental menace and crisis in human society.   methods   For investigation about existent situation of industrial waste generation questionnaire had been used. This questionnaire was catered by Iran environmental protection organization. Aforementioned questionnaire contained 45 questions about combination, quality and quantity of industrial waste. Total number of more than 50 personnel industry was 287 . But sample contained 50 randomly selected industries. Gathered data have been analyzed with spss 18.   Results  Total generated industrial waste was 123451KG per day which had volume equal to 781 cubic meters per day. Generated waste capitation per every worker was 5.8 KG. Maximum frequency of industrial was related to machinery and equipment group which maximum generated waste was related to this industrial group too. Maximum hazardous waste was for inflammable waste with 34 weight percent. Major hazardous waste generating industrial was chemical and plastic making industry.   Conclusion  yielded result from this investigation has shown that significant relation existed between waste production rate and personnel number. The more personnel are, the more waste production increase.

Atmospheric pollution problems and control proposals associated with solid waste management in China: a review.

Science.gov (United States)

Tian, Hezhong; Gao, Jiajia; Hao, Jiming; Lu, Long; Zhu, Chuanyong; Qiu, Peipei

2013-05-15

Along with population growth, rapid urbanization and industrialization process, the volume of municipal solid waste (MSW) generation in China has been increasing sharply in the past 30 years and the total amount of MSW yields will continue to increase. Nowadays, due to global warming warrants particular attention throughout the world, a series of air pollutants (including greenhouse gases, odorous gases, PCDD/Fs, heavy metals, PM, etc.) discharged from waste disposal and treatment processes have become one of the new significant emerging air pollution sources, which arousing great concerns about their adverse effects on surrounding ambient air quality and public health. At present, the overall safely disposed ratio of the collected MSW in China is reported at approximately 78% in 2010, and there are mainly three types of MSW disposal methods practiced in China, including landfill, composting and incineration. The characteristics of air pollutants and greenhouse gases discharge vary substantially among different MSW disposal methods. By presenting a thorough review of MSW generation in China and providing a summarization of the current status of MSW disposal methods practices, this review article makes an integrated overview analysis of existing air pollution problems associated with MSW collection, separation, and disposal processes. Furthermore, some comprehensive control proposals to prevent air pollution for improving MSW management of China in the future are put forward. Copyright © 2013 Elsevier B.V. All rights reserved.

Environmental pollution of polybrominated diphenyl ethers from industrial plants in China: a preliminary investigation.

Science.gov (United States)

Deng, Chao; Chen, Yuan; Li, Jinhui; Li, Ying; Li, Huafen

2016-04-01

Although numerous studies have shown the presence of polybrominated diphenyl ethers (PBDEs) in various environmental media, attention to their distribution in the environmental media surrounding industrial facilities is limited. In this study, eight PBDEs congeners (BDE-28, -47, -99, -100, -153, -154, -183, -209) were investigated in surface soils and water samples collected from commercial PBDE manufacturers, flame-retardant plastic modification plants and waste electrical and electronic equipment recycling facilities in China. Analysis of target compounds was performed using the model NCI GC-MS in SIM mode. The concentrations of ∑8PBDEs varied from 193.1 to 22,004.3 ng/L in water samples and from 1209.3 to 226,906 ng/g dry wt in surface soils, respectively. More severe PBDE contamination, when compared with previously reported data, was found in industrial areas in this study. This indicates that these industrial areas are highly polluted with PBDEs. BDE-209 was the predominant congener, accounting for more than 94% in this study, except for a 68.75% portion at one site. Our results show that PBDE manufacturing and flame-retardant plastic modification plants, easily overlooked by the public, are two primary PBDE pollution sources although they affect surrounding areas. Further research is needed, aimed at managing industrial PBDE emissions and eliminating environmental PBDE pollution, to investigate the material flows and environmental fates of PBDEs in all stages of the life cycle.

Tracking the Global Distribution of Persistent Organic Pollutants Accounting for E-Waste Exports to Developing Regions.

Science.gov (United States)

Breivik, Knut; Armitage, James M; Wania, Frank; Sweetman, Andrew J; Jones, Kevin C

2016-01-19

Elevated concentrations of various industrial-use Persistent Organic Pollutants (POPs), such as polychlorinated biphenyls (PCBs), have been reported in some developing areas in subtropical and tropical regions known to be destinations of e-waste. We used a recent inventory of the global generation and exports of e-waste to develop various global scale emission scenarios for industrial-use organic contaminants (IUOCs). For representative IUOCs (RIUOCs), only hypothetical emissions via passive volatilization from e-waste were considered whereas for PCBs, historical emissions throughout the chemical life-cycle (i.e., manufacturing, use, disposal) were included. The environmental transport and fate of RIUOCs and PCBs were then simulated using the BETR Global 2.0 model. Export of e-waste is expected to increase and sustain global emissions beyond the baseline scenario, which assumes no export. A comparison between model predictions and observations for PCBs in selected recipient regions generally suggests a better agreement when exports are accounted for. This study may be the first to integrate the global transport of IUOCs in waste with their long-range transport in air and water. The results call for integrated chemical management strategies on a global scale.

Waste to energy plant-air pollution monitoring and reporting

International Nuclear Information System (INIS)

Mullowney, R.L.

1988-01-01

We can't eat it. We can't wear it. We are running out of places to bury it. We can't export it. We can't stop making it. Garbage seems to be, by volume at least, our biggest national product. These facts are driving more and more industries and municipalities to construct waste to energy plants. Following the adage that when you get lemons, make lemonade, municipalities have been burning their garbage to produce steam and electricity. Communities, fearful that what they have produced may be toxic to them when burned, have enacted stringent air pollution control and monitoring regulations. The federal government has enacted regulations under the Clean Air Act 43 CFR Part 60 which regulate the emission limits monitoring and reporting requirements of waste energy plants. The most important of these regulations was enacted on December 16, 1987 and June 26, 1987, regulating particulate, SO 2 and NO x emissions. This paper reports that these regulations also tie in to various other EPA regulations and requirements. The most important of these to air pollution monitoring is Appendix F, Quality Assurance. However, these regulations are only minimum requirements -- individual states further strengthen their bite by requiring lower emissions limits and the monitoring of additional parameters such as H 2 S, HCl, NH 2 , CO, CO 2 and moisture. These monitoring limits and reporting requirements are currently being negotiated on a case by case basis in most instances

Trends in the Drilling Waste Management

Directory of Open Access Journals (Sweden)

Lucyna Czekaj

2006-10-01

Full Text Available Petroleum Industry is trying to achieve sustainable development goals. Each year new solutions are implemented to minimize the environmental impact of drilling operations. The paper presents trends in the drilling waste management caused by introducing the sustainable development into the petroleum industry. Old solutions such as the drilling waste disposal at the waste dump or dumping ground are not acceptable from the environmental point of view. The paper presents an analysis of new solutions as the sustainable solutions. The most important problem is the chemical pollution in cuttings and the waste drilling mud. The industrial solutions as well as the laboratory research on the pollution removing from drilling wastes are analysed. The most promising method seems to be the recycling and design for the environment of drilling mud.

Technique for Reduction of Environmental Pollution from Construction Wastes

Science.gov (United States)

Bakaeva, N. V.; Klimenko, M. Y.

2017-11-01

The results of the research on the negative impact construction wastes have on the urban environment and construction ecological safety are described. The research results are based on the statistical data and indicators calculated with the use of environmental pollution assessment in the restoration system of urban buildings technical conditions. The technique for the reduction of environmental pollution from construction wastes is scientifically based on the analytic summary of scientific and practical results for ecological safety ensuring at major overhaul and current repairs (reconstruction) of the buildings and structures. It is also based on the practical application of the probability theory method, system analysis and disperse system theory. It is necessary to execute some stages implementing the developed technique to reduce environmental pollution from construction wastes. The stages include various steps starting from information collection to the system formation with optimum performance characteristics which are more resource saving and energy efficient for the accumulation of construction wastes from urban construction units. The following tasks are solved under certain studies: basic data collection about construction wastes accumulation; definition and comparison of technological combinations at each system functional stage intended for the reduction of construction wastes discharge into the environment; assessment criteria calculation of resource saving and energy efficiency; optimum working parameters of each implementation stage are created. The urban construction technique implementation shows that the resource saving criteria are from 55.22% to 88.84%; potential of construction wastes recycling is 450 million tons of construction damaged elements (parts).

Proceedings of the 3. International conference on waste management in the chemical and petrochemical industries. Volume 1 and 2.

Energy Technology Data Exchange (ETDEWEB)

Lima, Francisco F; Pereira Filho, Francisco A; Almeida, Sergio A.S. [eds.

1994-12-31

To produce without pollution is today a mandate for the preservation of our society. To produce cleaner means to conserve energy and natural resources, to reduce the use of toxic substances, to invest in the evolution of products and production processes towards a minimum of residues. The Third International Conference on Waste Minimization in the Chemical and Petrochemical Industries addresses these challenging questions regarding waste minimization

Proceedings of the 3. International conference on waste management in the chemical and petrochemical industries. Volume 1 and 2.

Energy Technology Data Exchange (ETDEWEB)

Lima, Francisco F.; Pereira Filho, Francisco A.; Almeida, Sergio A.S. [eds.

1993-12-31

To produce without pollution is today a mandate for the preservation of our society. To produce cleaner means to conserve energy and natural resources, to reduce the use of toxic substances, to invest in the evolution of products and production processes towards a minimum of residues. The Third International Conference on Waste Minimization in the Chemical and Petrochemical Industries addresses these challenging questions regarding waste minimization

Electronic wastes

Science.gov (United States)

Regel-Rosocka, Magdalena

2018-03-01

E-waste amount is growing at about 4% annually, and has become the fastest growing waste stream in the industrialized world. Over 50 million tons of e-waste are produced globally each year, and some of them end up in landfills causing danger of toxic chemicals leakage over time. E-waste is also sent to developing countries where informal processing of waste electrical and electronic equipment (WEEE) causes serious health and pollution problems. A huge interest in recovery of valuable metals from WEEE is clearly visible in a great number of scientific, popular scientific publications or government and industrial reports.

Determining organic pollutants in automotive industry sludge.

Science.gov (United States)

Munaretto, Juliana S; Wonghon, Audrey L; von Mühlen, Carin

2012-12-01

In Brazil, the policy for disposing industrial sludge is changing from an emphasis on using controlled landfills to other treatment or co-processing methods; however, the monitoring of organic pollutants is not mandatory. The present study evaluated two general screening methods for organic pollutants in sludge generated in an automotive industrial complex in southern Brazil. The screening was performed using Soxhlet and sonication extractions and Gas Chromatograph coupled with Quadrupole Mass Spectrometry (GC/qMS). It was concluded that both techniques were effective and that most of the compounds identified were alkanes, phenols and esters. Important pollutants were detected in the sludge, which confirms the necessity of monitoring this type of residue.

Logistic paradigm for industrial solid waste treatment processes

OpenAIRE

Janusz Grabara; Ioan Constantin Dima

2014-01-01

Due to the fact that industrial waste are a growing problem, both economic and environmental as their number is increasing every year, it is important to take measures to correctly dealing wi th industrial waste. This article presents the descriptive model of logistics processes concerning the management of industrial waste. In this model the flow of waste begins in the place of production and ends at their disposal. The article presents the concept of logistics model in graphical form...

Growth with pollution: unsustainable development in Taiwan and its consequences.

Science.gov (United States)

Chi, C C

1994-01-01

Mutually supportive relationships between the Koumington (KMT) government and the private economic sector in Taiwan foster economic growth, which is incompatible with environmental protection. Environmental degradation in Taiwan is due almost exclusively to rapid economic growth; Taiwan should not be used as an example for developing countries. Taiwan's economic success was made possible because it did not have restrictions on pollution that its trading partners did. Air pollution reports in 1989 amounted to about 24 cases per day of appeals to environmental agencies country-wide. Major urban pollution sources include car, motorcycle, and industrial emissions. Acts passed in 1975 and 1982 have had little impact. Water pollution is caused by domestic sewage (25%), industrial waste water (54%), and domestic animal waste (21%). Untreated sewage in the water contributes to a high rate of hepatitis. Soil contamination is due to industrial development and agricultural intensification. Hazardous waste is dumped in the countryside; 3000 people in 1986 were poisoned by PCB-contaminated waste. Noise pollution standards are set at 60 decibels in residential areas and 65 decibels outside residential areas, but most find these levels too high. Industrial and toxic waste amounted in 1988 to 57,499 tons per day or 50% of Japan's volume. Waste is freely dumped into the air, water, and land. The food chain has been affected, and occupational diseases and cancer have doubled in 30 years. Deforestation on steep slopes contributes to serious soil erosion and fresh water resources problems. Economic growth maintains political legitimacy, sustains relationships between the government and the capitalist elites, and contributes to its monopoly of economic activities. The KMT government control of enterprises increased from 1 to 94 between the 1970s and 1986, while production by public enterprises declined over the same period. The Environmental Protection Agency has not been effective

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

Energy Technology Data Exchange (ETDEWEB)

Grumski, J. T.; Swindle, D. W.; Bates, L. D.; DeLozier, M. F.P.; Frye, C. E.; Mitchell, M. E.

1991-09-30

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy.

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

International Nuclear Information System (INIS)

1991-01-01

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy

Industrial Waste Landfill IV upgrade package

International Nuclear Information System (INIS)

1994-01-01

The Y-12 Plant, K-25 Site, and ORNL are managed by DOE's Operating Contractor (OC), Martin Marietta Energy Systems, Inc. (Energy Systems) for DOE. Operation associated with the facilities by the Operating Contractor and subcontractors, DOE contractors and the DOE Federal Building result in the generation of industrial solid wastes as well as construction/demolition wastes. Due to the waste streams mentioned, the Y-12 Industrial Waste Landfill IV (IWLF-IV) was developed for the disposal of solid industrial waste in accordance to Rule 1200-1-7, Regulations Governing Solid Waste Processing and Disposal in Tennessee. This revised operating document is a part of a request for modification to the existing Y-12 IWLF-IV to comply with revised regulation (Rule Chapters 1200-1-7-.01 through 1200-1-7-.08) in order to provide future disposal space for the ORR, Subcontractors, and the DOE Federal Building. This revised operating manual also reflects approved modifications that have been made over the years since the original landfill permit approval. The drawings referred to in this manual are included in Drawings section of the package. IWLF-IV is a Tennessee Department of Environmental and Conservation/Division of Solid Waste Management (TDEC/DSWM) Class 11 disposal unit

Characteristics and management of infectious industrial waste in Taiwan

International Nuclear Information System (INIS)

Huang, M.-C.; Lin, Jim Juimin

2008-01-01

Infectious industrial waste management in Taiwan is based on the specific waste production unit. In other countries, management is based simply on whether the producer may lead to infectious disease. Thus, Taiwan has a more detailed classification of infectious waste. The advantage of this classification is that it is easy to identify the sources, while the disadvantage lies in the fact that it is not flexible and hence increases cost. This study presents an overview of current management practices for handling infectious industrial waste in Taiwan, and addresses the current waste disposal methods. The number of small clinics in Taiwan increased from 18,183 to 18,877 between 2003 and 2005. Analysis of the data between 2003 and 2005 showed that the majority of medical waste was general industrial waste, which accounted for 76.9%-79.4% of total medical waste. Infectious industrial waste accounted for 19.3%-21.9% of total medical waste. After the SARS event in Taiwan, the amount of infectious waste reached 19,350 tons in 2004, an increase over the previous year of 4000 tons. Waste minimization was a common consideration for all types of waste treatment. In this study, we summarize the percentage of plastic waste in flammable infectious industrial waste generated by medical units, which, in Taiwan was about 30%. The EPA and Taiwan Department of Health have actively promoted different recycling and waste reduction measures. However, the wide adoption of disposable materials made recycling and waste reduction difficult for some hospitals. It has been suggested that enhancing the education of and promoting communication between medical units and recycling industries must be implemented to prevent recyclable waste from entering the incinerator

The case study of management of solid wastes in a petroleum industry; O estudo de caso do gerenciamento de residuos solidos em uma refinaria de petroleo

Energy Technology Data Exchange (ETDEWEB)

Araujo, Lizabela Souza de [Universidade Federal, Rio de Janeiro, RJ (Brazil). Escola de Quimica]. E-mail: lizabela@eq.ufrj.br; Nicolaiewsky, Elioni [Universidade Federal, Rio de Janeiro, RJ (Brazil). Escola de Quimica. Dept. de Engenharia Quimica]. E-mail: elioni@eq.ufrj.br; Freire, Denize D.C. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Escola de Quimica. Dept. de Engenharia Bioquimica]. E-mail: denize@eq.ufrj.br

2003-07-01

Crude oil refining is an industrial activity known as very pollutant, as all other activities of the petroleum industry, regarding either the volume or the concentration of the resides involved, thus generating emissions, effluents and solid wastes. The aim of the present work is to study solid waste management of a certain petroleum refinery, located in Rio de Janeiro. On the solid wastes management of that refinery, the following aspects were considered: origin and period of generation, conditioning, storage, transportation, treatment and final disposal. After listing all the resides and through analysis of the industrial wastes (norms, terms, inventory), the industrial process and office routines were then analyzed. The solid wastes were divided in two categories: industrial and administrative wastes. As far as destination is concerned, resides classified as Class I are either co-processed or incinerated, while Class II and Class III wastes, when not recycled, are sent to industrial or sanitary landfill. Finally, after analyzing the wastes management of the refinery, it has been proposed a plan of achievements in order to enhance the environmental goal of the refinery. (author)

Kraft pulping of industrial wood waste

Science.gov (United States)

Aziz. Ahmed; Masood. Akhtar; Gary C. Myers; Gary M. Scott

1998-01-01

Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for energy and/or landfilled. In this study, kraft pulp from industrial wood waste was evaluated and compared with softwood (loblolly pine, Douglas-fir) and hardwood (aspen) pulp. Pulp bleachability was also evaluated. Compared to loblolly pine...

Silicon carbide recovered from photovoltaic industry waste as photocatalysts for hydrogen production

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yu [College of Chemical Engineering, Sichuan University, Chengdu, 610064 (China); Hu, Yu [College of Material Science and Enginneering, Sichuan University, Chengdu, 610064 (China); Zeng, Hongmei [College of Chemistry, Sichuan University, Chengdu, 610064 (China); Zhong, Lin, E-mail: zhonglin@scu.edu.cn [College of Chemical Engineering, Sichuan University, Chengdu, 610064 (China); Liu, Kewei; Cao, Hongmei [College of Chemistry, Sichuan University, Chengdu, 610064 (China); Li, Wei [College of Material Science and Enginneering, Sichuan University, Chengdu, 610064 (China); Yan, Hongjian, E-mail: hjyan@scu.edu.cn [College of Chemistry, Sichuan University, Chengdu, 610064 (China)

2017-05-05

Highlights: • SiC was recovered from photovoltaic industry waste. • The recovered SiC is mainly consist of 3C-SiC, 6H-SiC and some silicon oxycarbides. • The recovered SiC shows photocatalytic H{sub 2} evolution from water. - Abstract: In recent years, the focus on creating a dependable and efficient means to recycle or recover the valuable parts from the waste material has drawn significantly attention as an environmentally friendly way to deal with the industrial wastes. The silicon carbide (SiC) crystalline is one of reusable material in the slurry wastes generated during wafer slicing. Here we report the use of recovered SiC from the slurry wastes as photocatalysts to produce hydrogen in the presence of Na{sub 2}SO{sub 3}-Na{sub 2}S as electron donor. The recovered SiC were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy spectra (XPS), UV–vis (UV–vis) spectroscopy, and photoluminescence (PL) spectroscopy. The morphology of SiC loaded with 1 wt% Pt as cocatalyst by thermal-reduction method was observed by scanning electron microscopy (SEM) and high resolution transmission electron microscopy (TEM). The experimental results reveal that the recovered SiC is mainly consist of 3C-SiC, 6H-SiC and some silicon oxycarbides on the surface of the SiC. The highest hydrogen production rate is 191.8 μmol h{sup −1} g{sup −1}. This study provides a way to recycle crystalline SiC from the discharged waste in the photovoltaic industry and reuse it as photocatalyst to yield hydrogen with the advantage of low energy consumption, low pollution and easy operation.

2016 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

Energy Technology Data Exchange (ETDEWEB)

Cafferty, Kara Grace [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (WRU-I-0160-01, Modification 1, formerly LA 000160 01), for the wastewater reuse site at the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2015, through October 31, 2016.

Assessment of hazardous solid waste of industries in Dashtestan county in the point of view of environment

Directory of Open Access Journals (Sweden)

A. Ameri

2008-10-01

Full Text Available Background and aims   Wastes are defined as a solid, liquid and gas materials that is produced from human activities, as direct or indirect. There is the possibility of linking between different complex of Geographic Information, which have a descriptive and locative relationship, simultaneously. GIS (Geographic Information System is as a bridge that it can relate resources  and management database together. The objective of this study was to investigate the condition of hazardous solid waste of industries in Dashtestan township and specification of volume and type of solid pollutants which probably can bring them in the environment and use of these outcomes for more recognition of establishment position of industries.   Methods   This study was evaluated on 8 industries according to type of products and type of each industry's hazardous solid waste. Then the 1/25000 scale digital topographic map was  provided and geographical coordination of each industries was determined by a GPS system. All of the obtained data were transferred to a GIS. Also a designed checklist and the existing standards were applied to determination of the list and the hazardous code of each industry.   Results   The obtained results showed that, 3 industries from 8, don't exactly conformed to the standards and in the sixth industry had susceptibility to be in the P category match to hazardous  waste list. All of the eight industries produced 174.5 ton/year of solid waste that 99.1% of them recycled after daily, monthly and seasonal storage.   Conclusion   62.5% of studied industries conformed to Iran protection agency's criteria, but some industries have a little problem in distance index from educational and residential centers.  Disposal of wastes in most industries didn't have any problem except in the sixth industries that   needs more investigation by experts and managers.

Pollution Sources in the nile and their environmental impacts

International Nuclear Information System (INIS)

Abd El- Bary, M.R.

1999-01-01

Over the past decades , the natural quality of water sources has been altered by the impact of various human activities and water uses. In Egypt, the Nile River which is considered as the main water source is still a recipient of most of the wastewater discharged by industrial effluents and several agriculture drains contains mixed wastes (sewage and industrial). These wastes includes a variety of pollutants which have considerable potential effect on both water ecosystem and human health. Monitoring of these pollutant is the first step for the improvement and protection of the Nile River .The Nile Research Institute designed a monitoring program includes collection and analysis of samples from 35 stations along the Nile River from Aswan to the Mediterranean Sea and from all points sources of pollution discharge their wastes into the Nile. The most important pollutant in these wastes are heavy metals, organic matters, inorganic compounds and micro organism causing disease

Industrial Water Waste, Problems and the Solution

Directory of Open Access Journals (Sweden)

Alif Noor Anna

2004-01-01

Full Text Available Recently, the long term development in Indonesia has changed agricultural sector to the industrial sector. This development can apparently harm our own people. This is due to the waste that is produced from factories. The waste from various factories seems to have different characteristics. This defference encourages us to be able to find out different of methods of managing waste so that cost can be reduced, especially in water treatment. In order that industrial development and environmental preservation can run together in balance, many institutions involved should be consider, especially in the industrial chain, the environment, and human resource, these three elements can be examined in terms of their tolerance to waste.

Petroleum industry is cleaning up its act -- Self-cleaning filters to maximize profits, minimize waste and reduce liability

International Nuclear Information System (INIS)

Williams, D.

2004-01-01

Recent steps taken by the petroleum industry to control end-of-pipe pollution and to minimize waste at the source by changing over to self-cleaning, backwashable filters instead of the traditional disposable filters such as bags or cartridges, are discussed. Various self-cleaning filter systems and their advantages are described, using REACTOGARD which provides total protection for catalysts in fixed-bed reactors and EROSIONGARD, used in fluidized catalytic crackers, as examples. Both filter systems have been developed by RPA Process Technologies, Inc., a global leader in industrial filtration systems. Major advantages attributed to self-cleaning filters include significantly reduced costs through reducing the number of catalyst change-out cycles, maximized platform productivity through virtually eliminating the risk of plugged wells, reduced waste through ability to recycle cleaning liquids, increased profits through shorter return-on-investment cycles, reduced emissions and reduced future liability through higher safety in the workplace; also reduced pollution of landfill sites. 1 photo

System analysis of industrial waste management: A case study of industrial plants located between Tehran and Karaj

Directory of Open Access Journals (Sweden)

Mohammad Amin Karami

2015-01-01

Full Text Available Aims: In this study, management of industrial waste in industries located between Tehran and Karaj in 2009-2010 was examined. Materials and Methods: This is a cross-sectional study which was done by site survey (Iranian environmental protection organization questionnaire usage and results analysis. This questionnaire was consisted of 45 questions about industrial waste, quantity, quality, and management. A total number of industries with over 50 employees was 283, and Stratified sampling method was used. Sample of size 50 was selected from 283cases. Results: The major hazardous waste-generating industries include chemical and plastic. Private sectors disposed 45% of generated waste. Majority of wastes were buried (62%, and only 17% of industrial waste was recycled. Conclusion: For hazardous waste reduction in this zone and health and economic attractions, the opportunity for reuse and recovery for these wastes must maximize in short-term and burial of industrial waste must be minimized. Industries such as chemical-plastic and electronics which have higher hazardous waste, in long-term, must be replaced with other industries such as wood cellulose and paper that have lower hazardous waste production rate.

Steel Industry Wastes.

Science.gov (United States)

Schmidtke, N. W.; Averill, D. W.

1978-01-01

Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

Environmental assessment of mining industry solid pollution in the mercurial district of Azzaba, northeast Algeria.

Science.gov (United States)

Seklaoui, M'hamed; Boutaleb, Abdelhak; Benali, Hanafi; Alligui, Fadila; Prochaska, Walter

2016-11-01

To date, there have been few detailed studies regarding the impact of mining and metallogenic activities on solid fractions in the Azzaba mercurial district (northeast Algeria) despite its importance and global similarity with large Hg mines. To assess the degree, distribution, and sources of pollution, a physical inventory of apparent pollution was developed, and several samples of mining waste, process waste, sediment, and soil were collected on regional and local scales to determine the concentration of Hg and other metals according to their existing mineralogical association. Several physico-chemical parameters that are known to influence the pollution distribution are realized. The extremely high concentrations of all metals exceed all norms and predominantly characterize the metallurgic and mining areas; the metal concentrations significantly decrease at significant low distances from these sources. The geo-accumulation index, which is the most realistic assessment method, demonstrates that soils and sediments near waste dumps and abandoned Hg mines are extremely polluted by all analyzed metals. The pollution by these metals decreases significantly with distance, which indicates a limited dispersion. The results of a clustering analysis and an integrated pollution index suggest that waste dumps, which are composed of calcine and condensation wastes, are the main source of pollution. Correlations and principal component analysis reveal the important role of hosting carbonate rocks in limiting pollution and differentiating calcine wastes from condensation waste, which has an extremely high Hg concentration (˃1 %).

Management approaches to integrated solid waste in industrialized zones in Jordan: a case of Zarqa City.

Science.gov (United States)

Mrayyan, Bassam; Hamdi, Moshrik R

2006-01-01

There is a need to recognize the difficulties experienced in managing waste and to understand the reasons for those difficulties, especially in developing countries such as Jordan. Zarqa is a Governorate located in central Jordan, which has 2874 registered industries, making up more than 52% of the total industries in the country. Zarqa Governorate suffers from serious solid waste problems. These problems arise from an absence of adequate policies, facilitating legislation, and an environmentally enthused public, which therefore have a negative impact on the environment and health. Solid waste generation in Zarqa Governorate has increased exponentially and has polluted natural resources and the environment. A significant change in municipal solid waste generation was evident between the years 1994 and 2000. The Zarqa Governorate generated 482 tons/day in 2002 with a per capita rate of 0.44 kg/cap-day [Consulting Engineers, 2002, Feasibility study for the treatment of industrial wastewater in Zarqa Governorate. A project funded by METAP and Zarqa Chamber of Industry. Unpublished report]. This manuscript assesses the current operational and management practices of solid waste in the Zarqa Governorate; and evaluates the associated issues of solid waste collection, storage, transport, disposal and recycling in developing countries. The lack of techniques, financial funds and awareness among public and private sectors form an obstacle for achieving a successful environmental program. Several options are proposed to address management goals. Although Jordan became the first country in the Middle East to adopt a national environmental strategy; waste disposal is still largely uncontrolled and large quantities of waste go uncollected. Ensuring proper management of solid wastes, enforcing regulations, and implementing proper environmental awareness programs that will enhance the public understanding and achieve greater efficiency, are the findings of this study.

Management approaches to integrated solid waste in industrialized zones in Jordan: A case of Zarqa City

International Nuclear Information System (INIS)

Mrayyan, Bassam; Hamdi, Moshrik R.

2006-01-01

There is a need to recognize the difficulties experienced in managing waste and to understand the reasons for those difficulties, especially in developing countries such as Jordan. Zarqa is a Governorate located in central Jordan, which has 2874 registered industries, making up more than 52% of the total industries in the country. Zarqa Governorate suffers from serious solid waste problems. These problems arise from an absence of adequate policies, facilitating legislation, and an environmentally enthused public, which therefore have a negative impact on the environment and health. Solid waste generation in Zarqa Governorate has increased exponentially and has polluted natural resources and the environment. A significant change in municipal solid waste generation was evident between the years 1994 and 2000. The Zarqa Governorate generated 482 tons/day in 2002 with a per capita rate of 0.44 kg/cap-day [Consulting Engineers, 2002, Feasibility study for the treatment of industrial wastewater in Zarqa Governorate. A project funded by METAP and Zarqa Chamber of Industry. Unpublished report]. This manuscript assesses the current operational and management practices of solid waste in the Zarqa Governorate; and evaluates the associated issues of solid waste collection, storage, transport, disposal and recycling in developing countries. The lack of techniques, financial funds and awareness among public and private sectors form an obstacle for achieving a successful environmental program. Several options are proposed to address management goals. Although Jordan became the first country in the Middle East to adopt a national environmental strategy; waste disposal is still largely uncontrolled and large quantities of waste go uncollected. Ensuring proper management of solid wastes, enforcing regulations, and implementing proper environmental awareness programs that will enhance the public understanding and achieve greater efficiency, are the findings of this study

Optimal waste heat recovery and reuse in industrial zones

International Nuclear Information System (INIS)

Stijepovic, Mirko Z.; Linke, Patrick

2011-01-01

Significant energy efficiency gains in zones with concentrated activity from energy intensive industries can often be achieved by recovering and reusing waste heat between processing plants. We present a systematic approach to target waste heat recovery potentials and design optimal reuse options across plants in industrial zones. The approach first establishes available waste heat qualities and reuse feasibilities considering distances between individual plants. A targeting optimization problem is solved to establish the maximum possible waste heat recovery for the industrial zone. Then, a design optimization problem is solved to identify concrete waste heat recovery options considering economic objectives. The paper describes the approach and illustrates its application with a case study. -- Highlights: → Developed a systematic approach to target waste heat recovery potentials and to design optimal recovery and reuse options across plants in industrial zones. → Five stage approach involving data acquisition, analysis, assessment, targeting and design. → Targeting optimization problem establishes the maximum possible waste heat recovery and reuse limit for the industrial zone. → Design optimization problem provides concrete waste heat recovery and reuse network design options considering economic objectives.

Wind erosion of waste impoundments in arid climates and mitigation of dust pollution.

Science.gov (United States)

Blight, G E

2008-12-01

Wind can erode and disperse fine-grained material from an impoundment of mining, industrial or municipal waste that stands above the level of its surroundings. Such dust dispersion can be a serious nuisance as well as a health hazard to inhabitants and animals in nearby settlements. It can also degrade crops, making them less marketable, and pollute soil, surface water and ground water. Wind can seasonally erode waste impoundments in all types of climate, but the erosion intensifies and persists for more of each year as regional aridity increases. As clouds of dust are often observed billowing across the top surfaces of waste impoundments in dry windy weather, there is a common misconception that dust arises from erosion of the top surface of an impoundment, resulting in much effort and money being misspent on top treatments when in fact the sloped sides of the impoundments are the true source of blown dust. This paper offers a brief review of general waste impoundment wind erosion issues and then focuses in more detail on the mechanics of how wind erodes surfaces of waste impoundments. Recommendations are offered for mitigating the effects of wind-eroded dust.

Solid waste containing persistent organic pollutants in Serbia: From precautionary measures to the final treatment (case study).

Science.gov (United States)

Stevanovic-Carapina, Hristina; Milic, Jelena; Curcic, Marijana; Randjelovic, Jasminka; Krinulovic, Katarina; Jovovic, Aleksandar; Brnjas, Zvonko

2016-07-01

Sustainable solid waste management needs more dedicated attention in respect of environmental and human health protection. Solid waste containing persistent organic pollutants is of special concern, since persistent organic pollutants are persistent, toxic and of high risk to human health and the environment. The objective of this investigation was to identify critical points in the Serbian system of solid waste and persistent organic pollutants management, to assure the life cycle management of persistent organic pollutants and products containing these chemicals, including prevention and final destruction. Data were collected from the Serbian competent authorities, and led us to identify preventive actions for solid waste management that should reduce or minimise release of persistent organic pollutants into the environment, and to propose actions necessary for persistent organic pollutants solid waste. The adverse impact of persistent organic pollutants is multidimensional. Owing to the lack of treatment or disposal plants for hazardous waste in Serbia, the only option at the moment to manage persistent organic pollutants waste is to keep it in temporary storage and when conditions are created (primarily financial), such waste should be exported for destruction in hazardous waste incinerators. Meanwhile, it needs to be assured that any persistent organic pollutants management activity does not negatively impact recycling flows or disturb progress towards a more circular economy in Serbia. © The Author(s) 2016.

Comprehensive waste characterization and organic pollution co-occurrence in a Hg and As mining and metallurgy brownfield

Energy Technology Data Exchange (ETDEWEB)

Gallego, J.R., E-mail: jgallego@uniovi.es [Environmental Technology, Biotechnology and Geochemistry Group, C/Gonzalo Gutiérrez Quirós s/n, 33600 Mieres, Asturias (Spain); Esquinas, N.; Rodríguez-Valdés, E.; Menéndez-Aguado, J.M. [Environmental Technology, Biotechnology and Geochemistry Group, C/Gonzalo Gutiérrez Quirós s/n, 33600 Mieres, Asturias (Spain); Sierra, C. [Environmental Technology, Biotechnology and Geochemistry Group, C/Gonzalo Gutiérrez Quirós s/n, 33600 Mieres, Asturias (Spain); Escuela Superior Politécnica del Litoral, Guayaquil (Ecuador)

2015-12-30

Highlights: • Complex legacy of contamination afflicts As–Hg brownfields. • As- and Hg-rich waste analyzed in a paradigmatic study site. • Co-ocurrence of a complex speciation of As and Hg, and organic pollution (PAHs). • Arsenolite was determined to be the main source of risk at the site. • Unexpected Hg organo-compounds found. - Abstract: The abandonment of Hg–As mining and metallurgy sites, together with long-term weathering, can dramatically degrade the environment. In this work it is exemplified the complex legacy of contamination that afflicts Hg–As brownfields through the detailed study of a paradigmatic site. Firstly, an in-depth study of the former industrial process was performed to identify sources of different types of waste. Subsequently, the composition and reactivity of As- and Hg-rich wastes (calcines, As-rich soot, stupp, and flue dust) was analyzed by means of multielemental analysis, mineralogical characterization (X-ray diffraction, electronic, and optical microscopy, microbrobe), chemical speciation, and sequential extractions. As-rich soot in the form of arsenolite, a relatively mobile by-product of the pyrometallurgical process, and stupp, a residue originated in the former condensing system, were determined to be the main risk at the site. In addition, the screening of organic pollution was also aimed, as shown by the outcome of benzo(a) pyrene and other PAHs, and by the identification of unexpected Hg organo-compounds (phenylmercury propionate). The approach followed unravels evidence from waste from the mining and metallurgy industry that may be present in other similar sites, and identifies unexpected contaminants overlooked by conventional analyses.

Potential of waste heat in Croatian industrial sector

Directory of Open Access Journals (Sweden)

Bišćan Davor

2012-01-01

Full Text Available Waste heat recovery in Croatian industry is of the highest significance regarding the national efforts towards energy efficiency improvements and climate protection. By recuperation of heat which would otherwise be wasted, the quantity of fossil fuels used for production of useful energy could be lowered thereby reducing the fuel costs and increasing the competitiveness of examined Croatian industries. Another effect of increased energy efficiency of industrial processes and plants is reduction of greenhouse gases i.e. the second important national goal required by the European Union (EU and United Nations Framework Convention on Climate Change (UNFCCC. Paper investigates and analyses the waste heat potential in Croatian industrial sector. Firstly, relevant industrial sectors with significant amount of waste heat are determined. Furthermore, significant companies in these sectors are selected with respect to main process characteristics, operation mode and estimated waste heat potential. Data collection of waste heat parameters (temperature, mass flow and composition is conducted. Current technologies used for waste heat utilization from different waste heat sources are pointed out. Considered facilities are compared with regard to amount of flue gas heat. Mechanisms for more efficient and more economic utilization of waste heat are proposed. [Acknoledgment. The authors would like to acknowledge the financial support provided by the UNITY THROUGH KNOWLEDGE FUND (UKF of the Ministry of Science, Education and Sports of the Republic of Croatia and the World Bank, under the Grant Agreement No. 89/11.

E-Alerts: Environmental pollution and control (solid waste pollution and control). E-mail newsletter

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-04-01

The paper discusses pollution by solid wastes including garbage, scrap, junked automobiles, spoil, sludge, containers; Disposal methods such as composts or land application, injection wells, incineration, sanitary landfills; Mining wastes; Processing for separation and materials recovery; Solid waste utilization; Recycling; Biological and ecological effects; Superfund (Records of Decision, etc.); SITE technology; Laws, legislation, and regulations; Public administration; Economics; Land use. The discussion includes disposal of concentrated or pure liquids such as brines, oils, chemicals, and hazardous materials.

Strategy of Water Pollution Control Base On Social Economic Activitiy, in Karang Mumus River, Samarinda East Kalimantan, Indonesia

Directory of Open Access Journals (Sweden)

Pramaningsih Vita

2018-01-01

Full Text Available Water Pollution in Karang Mumus River caused society behavior along the river. Daily activity such as bath, washing and defecate at the river. Garbage, sediment, domestic waste and flood are river problems should be solved. Purpose this research is make strategy of water pollution control in the Karang Mumus River. Method used observation in the field, interview to the society, industry, public activity along the river and government of environment department. Further create data using tool of Analysis Hierarchy Process (AHP to get the strategy to control water pollution in the river. Actors have contribute pollution control are government, industry and society. Criteria to pollution control are society participation, low, human resources and sustainable. Alternative of pollution control are unit garbage storage; license loyalty for industry and waste; communal waste water installation; monitoring of water quality. Result for actor priority are government (0.4; Industry (0.4; Society (0.2. Result for priority criteria are society participation (0.338, low (0.288, human resources (0.205 and sustainable (0.169. Result for priority alternative are unit garbage storage (0.433; license loyalty for industry and waste (0.238; communal waste water installation (0.169; monitoring of water quality (0.161.

Strategy of Water Pollution Control Base On Social Economic Activitiy, in Karang Mumus River, Samarinda East Kalimantan, Indonesia

Science.gov (United States)

Pramaningsih, Vita; Suprayogi, Slamet; Purnama, Setyawan

2018-02-01

Water Pollution in Karang Mumus River caused society behavior along the river. Daily activity such as bath, washing and defecate at the river. Garbage, sediment, domestic waste and flood are river problems should be solved. Purpose this research is make strategy of water pollution control in the Karang Mumus River. Method used observation in the field, interview to the society, industry, public activity along the river and government of environment department. Further create data using tool of Analysis Hierarchy Process (AHP) to get the strategy to control water pollution in the river. Actors have contribute pollution control are government, industry and society. Criteria to pollution control are society participation, low, human resources and sustainable. Alternative of pollution control are unit garbage storage; license loyalty for industry and waste; communal waste water installation; monitoring of water quality. Result for actor priority are government (0.4); Industry (0.4); Society (0.2). Result for priority criteria are society participation (0.338), low (0.288), human resources (0.205) and sustainable (0.169). Result for priority alternative are unit garbage storage (0.433); license loyalty for industry and waste (0.238); communal waste water installation (0.169); monitoring of water quality (0.161).

Current problems of marine pollution. Papers

International Nuclear Information System (INIS)

Dethlefsen, V.

1993-01-01

During the lecture meeting of the working committee for waste water problems of the German Fishery Association, papers were presented on current problems of waste pollution and on the potential effects of climate changes on the fishing industry. (EF) [de

Preparation and application of unhairing enzyme using solid wastes from the leather industry-an attempt toward internalization of solid wastes within the leather industry.

Science.gov (United States)

Ramesh, Renganath Rao; Muralidharan, Vimudha; Palanivel, Saravanan

2018-01-01

Usage of the animal fleshing waste as the source of carbon and nitrogen for animal skin unhairing protease (EC 3.4.21) production along with agro-industrial wastes like wheat bran has been investigated. Thermal hydrolysis of delimed fleshing waste for 3 h yielded a fleshing hydrolysate (FH) having a protein content of 20.86 mg/mL and total solids of 46,600 ppm. The FH was lyophilized and spray dried to obtain fleshing hydrolysate powder (FHP) to be used along with wheat bran and rice bran for protease production. The carbon, nitrogen, hydrogen, and sulfur contents of the FHP were found to be 40.1, 13.8, 5.4, and 0.2%. The control solid-state fermented (SSF) medium without FHP showed a maximum activity of only 550 U/g. A maximum protease activity of 956 U/g was obtained by using 6% FHP (taken based on the combined total weight of wheat bran and rice bran) after 96 h of fermentation, resulting in a 1.7-fold increase in the protease activity. The total cost of producing 1 kg of FHP and the cost of producing 1000 kU of protease using FHP along with wheat bran and rice bran were found to be USD 24.62 and USD 2.08, respectively; 25% of SSF protease along with 40% water was found to be capable of unhairing the sheepskins in 7 h eliminating the hazardous conventional lime sulfide unhairing system. Thus, the leather industry's solid waste internalized for the production of unhairing enzyme resulted in a sustainable solution for pollution problems. Graphical abstract ᅟ.

Prospects for pyrolysis technologies in managing municipal, industrial, and DOE cleanup wastes

Energy Technology Data Exchange (ETDEWEB)

Reaven, S.J. [State Univ. of New York, Stony Brook, NY (United States)

1994-12-01

Pyrolysis converts portions of municipal solid wastes, hazardous wastes, and special wastes such as tires, medical wastes, and even old landfills into solid carbon and a liquid or gaseous hydrocarbon stream. Pyrolysis heats a carbonaceous waste stream typically to 290--900 C in the absence of oxygen, and reduces the volume of waste by 90% and its weight by 75%. The solid carbon char has existing markets as an ingredient in many manufactured goods, and as an adsorbent or filter to sequester certain hazardous wastes. Pyrolytic gases may be burned as fuel by utilities, or liquefied for use as chemical feedstocks, or low-pollution motor vehicle fuels and fuel additives. This report analyzes the potential applications of pyrolysis in the Long Island region and evaluates for the four most promising pyrolytic systems their technological and commercial readiness, their applicability to regional waste management needs, and their conformity with DOE requirements for environmental restoration and waste management. This summary characterizes their engineering performance, environmental effects, costs, product applications, and markets. Because it can effectively treat those wastes that are inadequately addressed by current systems, pyrolysis can play an important complementing role in the region`s existing waste management strategy. Its role could be even more significant if the region moves away from existing commitments to incineration and MSW composting. Either way, Long Island could become the center for a pyrolysis-based recovery services industry serving global markets in municipal solid waste treatment and hazardous waste cleanup. 162 refs.

Prospects for pyrolysis technologies in managing municipal, industrial, and DOE cleanup wastes

International Nuclear Information System (INIS)

Reaven, S.J.

1994-12-01

Pyrolysis converts portions of municipal solid wastes, hazardous wastes, and special wastes such as tires, medical wastes, and even old landfills into solid carbon and a liquid or gaseous hydrocarbon stream. Pyrolysis heats a carbonaceous waste stream typically to 290--900 C in the absence of oxygen, and reduces the volume of waste by 90% and its weight by 75%. The solid carbon char has existing markets as an ingredient in many manufactured goods, and as an adsorbent or filter to sequester certain hazardous wastes. Pyrolytic gases may be burned as fuel by utilities, or liquefied for use as chemical feedstocks, or low-pollution motor vehicle fuels and fuel additives. This report analyzes the potential applications of pyrolysis in the Long Island region and evaluates for the four most promising pyrolytic systems their technological and commercial readiness, their applicability to regional waste management needs, and their conformity with DOE requirements for environmental restoration and waste management. This summary characterizes their engineering performance, environmental effects, costs, product applications, and markets. Because it can effectively treat those wastes that are inadequately addressed by current systems, pyrolysis can play an important complementing role in the region's existing waste management strategy. Its role could be even more significant if the region moves away from existing commitments to incineration and MSW composting. Either way, Long Island could become the center for a pyrolysis-based recovery services industry serving global markets in municipal solid waste treatment and hazardous waste cleanup. 162 refs

Long term industrial management of radioactive wastes in France

International Nuclear Information System (INIS)

Lavie, J.

1981-01-01

All human activities including energy generation entail the wastes. This definitely applies also to nuclear power generation. Currently the nuclear power program is very extensive, and the plans of fuel reprocessing proceed along this line. In consequence, the Government has decided on tackling the problem of industrial radioactive waste management in earnest. For the purpose, the National Radioactive Waste Management Agency (ANDRA) was created in November, 1979, within the French Atomic Energy Commission (CEA). Its main functions are the design, siting and construction of waste disposal centers and their management, the establishment of waste treatment and disposal standards, and the research and development. The following matters are described: the need for comprehensive industrial approach, the concept of industrial management, ANDRA business program, the industrial policy on waste disposal, and ANDRA financing. (J.P.N.)

Assessment of logistic outlays in industrial solid waste management

Directory of Open Access Journals (Sweden)

Janusz Grabara

2014-12-01

Full Text Available Out of concern for environmental protection is an increasingly common practice. Companies thus have an additional task which is the correct organization of the industrial waste management. This is achieved through the use of logistics processes in industrial waste management, mainly such as warehousing, transport, storage and recovery. These processes involve the formation of logistics costs resulting from waste management. The paper presents a mathematical model for cost of logistics management of industrial waste resulting from the above-mentioned processes. It also shows the interpretation of these costs and the relations between them. The model can increase costefficiency in companies managing industrial waste, while increasing attention to the environment.

Polluted rainwater runoff from waste recovery and recycling companies: Determination of emission levels associated with the best available techniques.

Science.gov (United States)

Huybrechts, D; Verachtert, E; Vander Aa, S; Polders, C; Van den Abeele, L

2016-08-01

Rainwater falling on outdoor storage areas of waste recovery and recycling companies becomes polluted via contact with the stored materials. It contains various pollutants, including heavy metals, polycyclic aromatic hydrocarbons and polychlorinated biphenyls, and is characterized by a highly fluctuating composition and flow rate. This polluted rainwater runoff is legally considered as industrial wastewater, and the polluting substances contained in the rainwater runoff at the point of discharge, are considered as emissions into water. The permitting authorities can set emission limit values (discharge limits) at the point of discharge. Best available techniques are an important reference point for setting emission limit values. In this paper, the emission levels associated with the best available techniques for dealing with polluted rainwater runoff from waste recovery and recycling companies were determined. The determination is based on an analysis of emission data measured at different companies in Flanders. The data show that a significant fraction of the pollution in rainwater runoff is associated with particles. A comparison with literature data provides strong indications that not only leaching, but also atmospheric deposition play an important role in the contamination of rainwater at waste recovery and recycling companies. The prevention of pollution and removal of suspended solids from rainwater runoff to levels below 60mg/l are considered as best available techniques. The associated emission levels were determined by considering only emission data from plants applying wastewater treatment, and excluding all samples with suspended solid levels >60mg/l. The resulting BAT-AEL can be used as a reference point for setting emission limit values for polluted rainwater runoff from waste recovery and recycling companies. Since the BAT-AEL (e.g. 150μg/l for Cu) are significantly lower than current emission levels (e.g. 300μg/l as the 90% percentile and 4910�

Numerical Simulation to Air Pollution Emission Control near an Industrial Zone

OpenAIRE

Oyjinda, Pravitra; Pochai, Nopparat

2017-01-01

A rapid industrial development causes several environment pollution problems. One of the main problems is air pollution, which affects human health and the environment. The consideration of an air pollutant has to focus on a polluted source. An industrial factory is an important reason that releases the air pollutant into the atmosphere. Thus a mathematical model, an atmospheric diffusion model, is used to estimate air quality that can be used to describe the sulfur dioxide dispersion. In thi...

Microbial assisted phyto extraction of metals and growth of soybean (glycine max l. merrill) on industrial waste water contaminated soil

International Nuclear Information System (INIS)

Ali, I.; Bano, A.

2012-01-01

Pots experiments were made to investigate the role of effective microorganisms (EM) in improving phyto extraction of metals (Cd/sup +2/ and Mn/sup +2/) and growth of soybean plant in industrial waste water polluted soil. Waste water applications to soil were made in four different dilutions (i.e. 25%, 50%, 75% and 100%). Effective microorganisms were added into waste water prior to application. Effect of treatments on growth parameters was studied. The Cd/sup +2/ and Mn/sup +2/ concentrations in different parts of plant were measured by Atomic Absorption Spectrophotometer. Plant height significantly increased at all treatments except at 25% waste water treatment. Plant dry biomass and oil contents in seed significantly increased with all treatments compared to control but were higher at low concentration of waste water. Waste water treatments significantly increased the Cd and Mn accumulation in plant while inoculation of EM further enhanced the metals accumulation. The maximum accumulation of Cd and Mn found in plant treated with 100% waste water in combination with effective microorganisms. At harvest, the Cd/sup +2/ concentration decreased in leaves but increased in roots followed by stem > seeds, while, Mn/sup +2/ accumulation increased in leaves followed by roots > stem > seeds. Conclusively, EM enhanced the phyto extraction of Cd and Mn and also increased the oil contents in soybean on polluted soil. These findings suggest further investigation to find out a suitable concentration of industrial waste water in combination with EM for better growth of soybean and improving phyto extraction of metals. (author)

Challenges in packaging waste management in the fast food industry

Energy Technology Data Exchange (ETDEWEB)

Aarnio, Teija [Digita Oy, P.O. Box 135, FI-00521 Helsinki (Finland); Haemaelaeinen, Anne [Department of Energy and Environmental Technology, Lappeenranta University of Technology, P.O. Box 20, FI-53851 Lappeenranta (Finland)

2008-02-15

The recovery of solid waste is required by waste legislation, and also by the public. In some industries, however, waste is mostly disposed of in landfills despite of its high recoverability. Practical experiences show that the fast food industry is one example of these industries. A majority of the solid waste generated in the fast food industry is packaging waste, which is highly recoverable. The main research problem of this study was to find out the means of promoting the recovery of packaging waste generated in the fast food industry. Additionally, the goal of this article was to widen academic understanding on packaging waste management in the fast food industry, as the subject has not gained large academic interest previously. The study showed that the theoretical recovery rate of packaging waste in the fast food industry is high, 93% of the total annual amount, while the actual recovery rate is only 29% of the total annual amount. The total recovery potential of packaging waste is 64% of the total annual amount. The achievable recovery potential, 33% of the total annual amount, could be recovered, but is not mainly because of non-working waste management practices. The theoretical recovery potential of 31% of the total annual amount of packaging waste cannot be recovered by the existing solid waste infrastructure because of the obscure status of commercial waste, the improper operation of producer organisations, and the municipal autonomy. The research indicated that it is possible to reach the achievable recovery potential in the existing solid waste infrastructure through new waste management practices, which are designed and operated according to waste producers' needs and demands. The theoretical recovery potential can be reached by increasing the consistency of the solid waste infrastructure through governmental action. (author)

Solvent extraction as additional purification method for postconsumer plastic packaging waste

NARCIS (Netherlands)

Thoden van Velzen, E.U.; Jansen, M.

2011-01-01

An existing solvent extraction process currently used to convert lightly polluted post-industrial packaging waste into high quality re-granulates was tested under laboratory conditions with highly polluted post-consumer packaging waste originating from municipal solid refuse waste. The objective was

Economic development and multiple air pollutant emissions from the industrial sector.

Science.gov (United States)

Fujii, Hidemichi; Managi, Shunsuke

2016-02-01

This study analyzed the relationship between economic growth and emissions of eight environmental air pollutants (carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), nitrogen oxide (NOx), sulfur oxide (SOx), carbon monoxide (CO), non-methane volatile organic compound (NMVOC), and ammonia (NH3)) in 39 countries from 1995 to 2009. We tested an environmental Kuznets curve (EKC) hypothesis for 16 individual industry sectors and for the total industrial sector. The results clarified that at least ten individual industries do not have an EKC relationship in eight air pollutants even though this relationship was observed in the country and total industrial sector level data. We found that the key industries that dictated the EKC relationship in the country and the total industrial sector existed in CO2, N2O, CO, and NMVOC emissions. Finally, the EKC turning point and the relationship between economic development and trends of air pollutant emissions differ among industries according to the pollution substances. These results suggest inducing new environmental policy design such as the sectoral crediting mechanism, which focuses on the industrial characteristics of emissions.

Radioactive wastes. Their industrial management

International Nuclear Information System (INIS)

Lavie, J.M.

1982-01-01

This paper introduces a series that will review the present situation in the field of long-term management of radioactive wastes. Both the meaning and the purposes of an industrial management of radioactive wastes are specified. This short introduction is complemented by outline of data on the French problem [fr

Assessment of Food Processing and Pharmaceutical Industrial Wastes as Potential Biosorbents: A Review

Science.gov (United States)

El-Sayed, Hanan E. M.; El-Sayed, Mayyada M. H.

2014-01-01

There is a growing need for the use of low-cost and ecofriendly adsorbents in water/wastewater treatment applications. Conventional adsorbents as well as biosorbents from different natural and agricultural sources have been extensively studied and reviewed. However, there is a lack of reviews on biosorption utilizing industrial wastes, particularly those of food processing and pharmaceuticals. The current review evaluates the potential of these wastes as biosorbents for the removal of some hazardous contaminants. Sources and applications of these biosorbents are presented, while factors affecting biosorption are discussed. Equilibrium, kinetics, and mechanisms of biosorption are also reviewed. In spite of the wide spread application of these biosorbents in the treatment of heavy metals and dyes, more research is required on other classes of pollutants. In addition, further work should be dedicated to studying scaling up of the process and its economic feasibility. More attention should also be given to enhancing mechanical strength, stability, life time, and reproducibility of the biosorbent. Environmental concerns regarding disposal of consumed biosorbents should be addressed by offering feasible biosorbent regeneration or pollutant immobilization options. PMID:25110656

Assessment of food processing and pharmaceutical industrial wastes as potential biosorbents: a review.

Science.gov (United States)

El-Sayed, Hanan E M; El-Sayed, Mayyada M H

2014-01-01

There is a growing need for the use of low-cost and ecofriendly adsorbents in water/wastewater treatment applications. Conventional adsorbents as well as biosorbents from different natural and agricultural sources have been extensively studied and reviewed. However, there is a lack of reviews on biosorption utilizing industrial wastes, particularly those of food processing and pharmaceuticals. The current review evaluates the potential of these wastes as biosorbents for the removal of some hazardous contaminants. Sources and applications of these biosorbents are presented, while factors affecting biosorption are discussed. Equilibrium, kinetics, and mechanisms of biosorption are also reviewed. In spite of the wide spread application of these biosorbents in the treatment of heavy metals and dyes, more research is required on other classes of pollutants. In addition, further work should be dedicated to studying scaling up of the process and its economic feasibility. More attention should also be given to enhancing mechanical strength, stability, life time, and reproducibility of the biosorbent. Environmental concerns regarding disposal of consumed biosorbents should be addressed by offering feasible biosorbent regeneration or pollutant immobilization options.

Pollution prevention constraints within DOE facilities

International Nuclear Information System (INIS)

Walzer, A.E.

1992-01-01

The signing of the Pollution Prevention Act of 1990, has marked a new environmental era. The 1990s environmental movement is shifting from ''end of the pipe'' treatment towards a philosophy of source reduction (predicated by the Pollution Prevention Act), where engineering solutions and materials substitution are sought to reduce the volume and toxicity of waste. This change comes after 20 years of treatment legislation, where in many cases the location or media in which our pollution is deposited was merely changed. This problem is exemplified by the enormous environmental problems created by waste sites. Our inability to deal with the substantial waste generated has produced the environmental legacy on the Department of Energy (DOE) sites, a legacy that will cost billions of dollars to remediate. How then do we solve our waste problems and avoid future legacies? This paper outlines some of the obstacles to pollution prevention within the DOE system and explores opportunities to remove these barriers. Industry, whose foundation is economics, has found it attractive to reduce their wastes, particularly in the wake of escalating waste disposal costs. However, within federal facilities where basic economic principles do not prevail, incentives towards pollution prevention need to be evaluated. Our current system of segregated DOE programs creates obstacles for waste generators to work productively with other programs. Certain policies and practices also limit the generators' responsibility and costs for their waste, which is counter productive to waste minimization and pollution prevention. To meet new environmental challenges and to be proactive in pollution prevention we must evaluate our systems and remove barriers that impede progress toward pollution prevention

Atmospheric pollution problems and control proposals associated with solid waste management in China: A review

International Nuclear Information System (INIS)

Tian, Hezhong; Gao, Jiajia; Hao, Jiming; Lu, Long; Zhu, Chuanyong; Qiu, Peipei

2013-01-01

Highlights: ► Air pollution problems generated in MSW management processes in China are presented. ► Both quantity and composition of MSW generation in China are identified. ► The status of different methods for MSW treatment and disposal are reviewed. ► Some comprehensive control proposals for improving MSW management are proposed. -- Abstract: Along with population growth, rapid urbanization and industrialization process, the volume of municipal solid waste (MSW) generation in China has been increasing sharply in the past 30 years and the total amount of MSW yields will continue to increase. Nowadays, due to global warming warrants particular attention throughout the world, a series of air pollutants (including greenhouse gases, odorous gases, PCDD/Fs, heavy metals, PM, etc.) discharged from waste disposal and treatment processes have become one of the new significant emerging air pollution sources, which arousing great concerns about their adverse effects on surrounding ambient air quality and public health. At present, the overall safely disposed ratio of the collected MSW in China is reported at approximately 78% in 2010, and there are mainly three types of MSW disposal methods practiced in China, including landfill, composting and incineration. The characteristics of air pollutants and greenhouse gases discharge vary substantially among different MSW disposal methods. By presenting a thorough review of MSW generation in China and providing a summarization of the current status of MSW disposal methods practices, this review article makes an integrated overview analysis of existing air pollution problems associated with MSW collection, separation, and disposal processes. Furthermore, some comprehensive control proposals to prevent air pollution for improving MSW management of China in the future are put forward

Atmospheric pollution problems and control proposals associated with solid waste management in China: A review

Energy Technology Data Exchange (ETDEWEB)

Tian, Hezhong, E-mail: hztian@bnu.edu.cn [State Key Joint Laboratory of Environmental Simulation and Pollution Control, School of Environment, Beijing Normal University, Beijing 100875 (China); Gao, Jiajia [State Key Joint Laboratory of Environmental Simulation and Pollution Control, School of Environment, Beijing Normal University, Beijing 100875 (China); Hao, Jiming [School of Environment, Tsinghua University, Beijing 100084 (China); Lu, Long; Zhu, Chuanyong; Qiu, Peipei [State Key Joint Laboratory of Environmental Simulation and Pollution Control, School of Environment, Beijing Normal University, Beijing 100875 (China)

2013-05-15

Highlights: ► Air pollution problems generated in MSW management processes in China are presented. ► Both quantity and composition of MSW generation in China are identified. ► The status of different methods for MSW treatment and disposal are reviewed. ► Some comprehensive control proposals for improving MSW management are proposed. -- Abstract: Along with population growth, rapid urbanization and industrialization process, the volume of municipal solid waste (MSW) generation in China has been increasing sharply in the past 30 years and the total amount of MSW yields will continue to increase. Nowadays, due to global warming warrants particular attention throughout the world, a series of air pollutants (including greenhouse gases, odorous gases, PCDD/Fs, heavy metals, PM, etc.) discharged from waste disposal and treatment processes have become one of the new significant emerging air pollution sources, which arousing great concerns about their adverse effects on surrounding ambient air quality and public health. At present, the overall safely disposed ratio of the collected MSW in China is reported at approximately 78% in 2010, and there are mainly three types of MSW disposal methods practiced in China, including landfill, composting and incineration. The characteristics of air pollutants and greenhouse gases discharge vary substantially among different MSW disposal methods. By presenting a thorough review of MSW generation in China and providing a summarization of the current status of MSW disposal methods practices, this review article makes an integrated overview analysis of existing air pollution problems associated with MSW collection, separation, and disposal processes. Furthermore, some comprehensive control proposals to prevent air pollution for improving MSW management of China in the future are put forward.

Industrial aspects of radioactive waste management in Western Europe

International Nuclear Information System (INIS)

Marcus, F.R.

1976-01-01

Various aspects of waste management are discussed from the viewpoint of the nuclear industry. Future amounts of waste generated in the 15 Foratom countries in Western Europe are estimated. Industrial waste questions--as seen by electricity producers, reprocessors, and waste operators--are discussed; questions concerning decommissioning are also dealt with. A number of recommendations for further action, primarily on the part of national authorities and international organizations, are put forward. One conclusion of the study is that there is no reason for waste-management problems to impede the timely development of nuclear energy as a large-scale industrial activity in Western Europe

Annual report of waste generation and pollution prevention progress 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This seventh Annual Report presents and analyzes DOE Complex-wide waste generation and pollution prevention activities at 45 reporting sites from 1993 through 1998. This section summarizes Calendar Year 1998 Complex-wide waste generation and pollution prevention accomplishments. More detailed information follows this section in the body of the Report. In May 1996, the Secretary of Energy established a 50 percent Complex-Wide Waste Reduction Goal (relative to the 1993 baseline) for routine operations radioactive, mixed, and hazardous waste generation, to be achieved by December31, 1999. DOE has achieved its Complex-Wide Waste Reduction Goals for routine operations based upon a comparison of 1998 waste generation to the 1993 baseline. Excluding sanitary waste, routine operations waste generation decreased 67 percent overall from 1993 to 1998. However, for the first time since 1994, the total amount of materials recycled by the Complex decreased from 109,600 metric tons in 1997 to 92,800 metric tons in 1998. This decrease is attributed to the fact that in 1997, several large ''one-time only'' recycling projects were conducted throughout the Complex. In order to demonstrate commitment to DOE's Complex-wide recycling goal, it is important for sites to identify all potential large-scale recycling/reuse opportunities.

Clean Air Act Guidelines and Standards for Waste Management

Science.gov (United States)

This page contains the stationary sources of air pollution for the waste management industries, and their corresponding air pollution regulations. To learn more about the regulations for each industry, just click on the links below.

Clearance level and industrial waste management

International Nuclear Information System (INIS)

Asano, Toichi

1999-01-01

Defining the clearance level enables the radioactive waste with lower radioactivity than a certain level to be the general industrial waste and therefore consideration for public acceptance is essential. For this, it is necessary to understand laws concerning not only atomic power and radioactivity but also disposal and cleaning of general waste. It is also necessary that the waste below the clearance level should be as much as possible handled in the modern common concept of recycling of resources. In 1996, the weight of industrial waste was about 400 million tons, of which 40% was disposed by burning and dehydration, 39% was re-used and 21% was subjected to the final disposal like reclamation. Reduction, re-use and recycling of the generated waste are required for making the society with recycling of resources. Scrap concrete materials below the clearance level of 0.6 million tons are estimated to be generated by dismantling the light water reactor of 1 million kW output and profitable technology for recycling the scrap is under investigation. (K.H.)

Alternative approaches to pollution control and waste management: Regulatory and economic instruments

International Nuclear Information System (INIS)

Bernstein, J.D.

1993-01-01

The purpose of the paper is to present an overview of the most common strategies and policy instruments (that is, regulatory and economic) used in developed and developing countries to achieve pollution control and waste management objectives. Although this topic has been at the center of theoretical controversy both within and outside the World Bank, the paper is not intended to contribute to this debate. Rather, its purpose is to explore how regulatory and economic instruments are used to control air and water pollution, protect ground water, and manage solid and hazardous wastes. The paper is directed to policy makers at the national, state, and local levels of government, as well as to other parties responsible for pollution control and waste management programs

Effect of industrial pollution on behaviour of radionuclides in forest ecosystems

International Nuclear Information System (INIS)

Outola, I.

2009-01-01

To investigate how and to what extent industrial pollution affects the behaviour of radionuclides in forest ecosystems, studies were conducted in the vicinity of two Cu-Ni smelters: one in a pine forest at Harjavalta, Finland, and the other in a spruce forest at Monchegorsk, Russia. Industrial pollution had significant effects on the distribution of radionuclides in soil horizons. With the increase in pollution towards the smelter, radionuclides were accumulated more in the litter layer because the conversion of litter into organic material was diminished due to inhibited microbial activity. As a result, the organic layer contained less radionuclides towards the smelter. The effect of industrial pollution on soil-to-plant transfer was complex. The effect varied with radionuclide, plant species and also on forest type. For 137 Cs, soil-to-plant transfer decreased significantly as industrial pollution increased in pine forest, whereas the decrease was less pronounced in spruce forest. Root uptake of 239,240 Pu by plants is extremely small, and plant contamination by resuspended soil is an important factor in considering the soil-to-plant transfer of this radionuclide. In spruce forest, more plutonium was transferred into plants when pollution load increased due to resuspension of litter particles, which contained higher concentrations of plutonium in the vicinity of the smelter. Soil-to-plant transfer of plutonium was much less affected in pine forests contaminated with industrial pollution. This research clearly indicates the sensitivity of the northern forest ecosystem to inorganic pollutants. Prediction of the soil-to-plant transfer of radionuclides in industrially polluted forest ecosystems requires detailed information on the total deposition, vertical distribution of radionuclides in soil, soil microbiological factors, other soil parameters as well as the rooting depths of the plants. (LN)

Ecological problems of oil wastes

International Nuclear Information System (INIS)

Mohsun, R.

2004-01-01

Full text : Pollution of the environment with different wastes is one the main problems in the world. So that is why this article is devoted to consideration of questions, related to oil and its industry. During oil production (extraction, transportation, refining) different wastes (homogeneous and solid wastes) are taken out from a place of production to the environment and after this environment undergoes the pollution because of these wastes. These wastes contain first of all harmful for environment radioactive elements, then different groups of metals, non-metals and other combinations. All these forms technical pollution zones and can cause serious danger for health of people. So taking into consideration all mentioned above we must make all efforts in order to prevent such accidents

Good Practice Guide Waste Minimization/Pollution Prevention

Energy Technology Data Exchange (ETDEWEB)

J Dorsey

1999-10-14

This Good Practice Guide provides tools, information, and examples for promoting the implementation of pollution prevention during the design phases of U.S. Department of Energy (DOE) projects. It is one of several Guides for implementing DOE Order 430.1, Life-cycle Asset Management. DOE Order 430.1 provides requirements for DOE, in partnership with its contractors, to plan, acquire, operate, maintain, and dispose of physical assets. The goals of designing for pollution prevention are to minimize raw material consumption, energy consumption, waste generation, health and safety impacts, and ecological degradation over the entire life of the facility (EPA 1993a). Users of this Guide will learn to translate national policy and regulatory requirements for pollution prevention into action at the project level. The Guide was written to be applicable to all DOE projects, regardless of project size or design phase. Users are expected to interpret the Guide for their individual project's circumstances, applying a graded approach so that the effort is consistent with the anticipated waste generation and resource consumption of the physical asset. This Guide employs a combination of pollution prevention opportunity assessment (PPOA) methods and design for environment (DfE) philosophies. The PPOA process was primarily developed for existing products, processes, and facilities. The PPOA process has been modified in this Guide to address the circumstances of the DOE design process as delineated in DOE Order 430.1 and its associated Good Practice Guides. This modified form of the PPOA is termed the Pollution Prevention Design Assessment (P2DA). Information on current nationwide methods and successes in designing for the environment also have been reviewed and are integrated into this guidance.

Industrial effluent quality, pollution monitoring and environmental management.

Science.gov (United States)

Ahmad, Maqbool; Bajahlan, Ahmad S; Hammad, Waleed S

2008-12-01

Royal Commission Environmental Control Department (RC-ECD) at Yanbu industrial city in Kingdom of Saudi Arabia has established a well-defined monitoring program to control the pollution from industrial effluents. The quality of effluent from each facility is monitored round the clock. Different strategic measures have been taken by the RC-ECD to implement the zero discharge policy of RC. Industries are required to pre-treat the effluent to conform pretreatment standards before discharging to central biological treatment plant. Industries are not allowed to discharge any treated or untreated effluent in open channels. After treatment, reclaimed water must have to comply with direct discharge standards before discharge to the sea. Data of industrial wastewater collected from five major industries and central industrial wastewater treatment plant (IWTP) is summarized in this report. During 5-year period, 3,705 samples were collected and analyzed for 43,436 parameters. There were 1,377 violations from pretreatment standards from all the industries. Overall violation percentage was 3.17%. Maximum violations were recorded from one of the petrochemical plants. The results show no significant pollution due to heavy metals. Almost all heavy metals were within RC pretreatment standards. High COD and TOC indicates that major pollution was due to hydrocarbons. Typical compounds identified by GC-MS were branched alkanes, branched alkenes, aliphatic ketones, substituted thiophenes, substituted phenols, aromatics and aromatic alcohols. Quality of treated water was also in compliance with RC direct discharge standards. In order to achieve the zero discharge goal, further studies and measures are in progress.

Annual report of waste generation and pollution prevention progress 1995

International Nuclear Information System (INIS)

1997-02-01

This fourth Annual Report presents and analyzes 1995 DOE complex-wide waste generation and pollution prevention activities at 40 reporting sites in 25 States, and trends DOE waste generation from 1991 through 1995. DOE has established a 50% reduction goal (relative to the 1993 baseline) for routine operations radioactive and hazardous waste generation, due by December 31, 1999. Routine operations waste generation decreased 37% from 1994 to 1995, and 43% overall from 1993--1995

Statutory Instruments - 1984 No. 863 and 1985 No. 708. Public Health, England and Wales - Public Health Scotland. The Control of Pollution (Radioactive Waste) Regulations 1984, The Control of Pollution (Radioactive Waste) Regulations 1985

International Nuclear Information System (INIS)

1985-01-01

The Regulations provide that radioactive waste is to be treated as any other waste for pollution control purposes as opposed to special radioactive control purposes. In the former respect, radioactive waste is subject to Part II of the Control of Pollution Act 1974, but in the latter, it remains subject to the Radioactive Substances Act 1960. (NEA) [fr

Bibliography on ocean waste disposal. second edition. Final report 1976

International Nuclear Information System (INIS)

Stanley, H.G.; Kaplanek, D.W.

1976-09-01

This research bibliography is restricted to documents relevant to the field of ocean waste disposal. It is primarily limited to recent publications in the categories of: ocean waste disposal; criteria; coastal zone management; monitoring; pollution control; dredge spoil; dredge spoin disposal; industrial waste disposal; radioactive waste; oil spills; bioassay; fisheries resources; ocean incineration; water chemistry; and, Water pollution

A Study on the Evaluation of Industrial Solid Waste Management ...

African Journals Online (AJOL)

Industrial solid waste is a serious health concern in Aba, South East Nigeria. This study was undertaken to assess the approaches of some industries toward some aspects of waste management in Aba. Interviews, observation and questionnaires administered to industry executives and waste managers were used to ...

Low-temperature waste-heat recovery in the food and paper industries

Energy Technology Data Exchange (ETDEWEB)

Foell, W.K.; Lund, D.; Mitchell, J.W.; Ray, D.; Stevenson, R.; TenWolde, A.

1980-11-01

The potential of low-temperature waste-heat recovery technology is examined. An examination of barriers to impede waste-heat recovery is made and research programs are identified. Extensive information and data are presented in the following chapters: Waste Heat Recovery in the Wisconsin Food Industry; Waste Heat Recovery in the Wisconsin Pulp and Paper Industry; Industries' Economic Analysis of Energy Conservation Projects; Industrial Waste Heat Recovery (selection of heat-recovery heat exchangers for industrial applications, simplified procedure for selection of heat recovery heat exchangers for industrial applications, selection of heat pumps for industrial applications); Institutional Aspects of Industrial Energy Conservation (economic motivation for energy conservation and the industrial response, intrafirm idea channels and their sources, evaluation and approval of plant improvement projects, reported barriers to adopting waste heat recovery projects and recommendations for government involvement, and the final chapter is a summary with major conclusions given. Additional information is given in two appendices on the potential waste heat recovery in a cheese plant (calculation) and conditions for optimum exchanger size and break-even fuel cost. (MCW)

The Implementation of Effluent Taxes for Cambodian Industry: An Assessment of Pollutant Levies

OpenAIRE

Sideth Muong

2006-01-01

This study looks at how the Cambodian government might introduce a pollution levy system to address the country's industrial pollution problem. Using information drawn from a variety of sources, including a recent industrial survey, it estimates the levels of pollution charges that would reduce pollution by 25%-85%. It also calculates the overall revenue that such levies would produce and estimates the costs that industry would have to bear in terms of abatement costs and pollution charges. B...

Pollution prevention at the Kansas City Division through process waste assessments

International Nuclear Information System (INIS)

Pemberton, S.E.; Gentile, C.C.

1992-01-01

Allied-Signal Inc., Kansas City Division (KCD) is committed to the hazardous waste minimization requirements set forth under RCRA as amended by the Pollution Prevention Act and DOE Order 5400.1. To assure compliance with these regulations, the KCD has developed a comprehensive Pollution Prevention Program which focuses on the elimination or minimization of all material releases to all environmental media. The ownership of waste minimization is given to all of the waste generators through Departmental Pollution Prevention Plans. These plans include tools to achieve the waste minimization goals. One of these tools is the process waste assessment (PWA). A PWA is a planned procedure with the objective of identifying opportunities and methods to reduce or eliminate waste. A material balance is performed around a specific process which qualifies and quantifies the materials entering and exiting the process. These materials are further defined to the hazardous component level. The exiting materials are separated into what goes into the product, sent to waste management, and what is released to the air (fugitive or point source). Next, opportunities are identified and evaluated for the ability to eliminate or minimize the waste streams exiting the process. Therefore, the PWA provides the basic tool for the creation of a comprehensive process baseline and identification of opportunities to eliminate/minimize the release of hazardous and non-hazardous wastes. This presentation will describe the status and activities of the program conceived to initiate PWAs at the Kansas City Division (KCD) of Allied-Signal Inc.. This program is organized through business units Which consist of manufacturing, quality, and engineering personnel from a specific product line. The departments that these business units represent are the generators of the major process waste at the KCD. Included in the update will be a brief overview of the lessons learned from the methodology development and

Technologies 1995: environment and wastes treatment

International Nuclear Information System (INIS)

Anon.

1995-03-01

From new technical or scientific developments, new products launching, and markets evolutions, this catalog gives informations selection on research and development projects, new fabrication processes, activities and plants strategies, licences or technology transfers opportunities. The covered fields are: atmospheric pollution controls, water and liquid wastes treatment, polluted soils treatments, noise and odors treatments, municipal and industrial wastes treatments (metal, plastic, paper, glass), clean materials and technologies, radioactive wastes, and european cooperation programs. (A.B.)

Air pollution sources, impact and monitoring

International Nuclear Information System (INIS)

Qureshi, I.H.

1999-01-01

Improper management of socio-economic developmental activities has put a great stress on natural resources and eco-systems and has caused environmental degradation. Indiscriminate release of toxic substances into the atmosphere from power generation, industrial operations, transportation, incineration of waste and other operations has affected the quality of ambient air. Combustion of fossil fuel results in the emission of oxides of carbon, sulfur and nitrogen, particulate and organic compounds which affect the local, regional and global environment. Industrial operations release a wide variety of pollutants which directly affect the local environment. Operation of automobiles releases oxides of carbon, sulfur and nitrogen, hydrocarbons, traces of heavy metals and toxic polycyclic aromatic compounds whereas incineration of municipal waste releases particulate, acid fumes and photochemically reactive and odorous compounds. These air pollutants have varying impacts on health and environment. The intake of polluted air may produce various physiological disorders ranging from respiratory diseases to changes in blood chemistry. Therefore, the emission of pollutants should be controlled at the source and monitoring the levels of pollution should assess the quality of air. (author)

Earthworms as bio-indicators of chemical pollution in soils with drilling waste

Directory of Open Access Journals (Sweden)

Kujawska Justyna

2017-01-01

Full Text Available The deposited drilling waste may alter the functioning of soil ecosystems by disrupting the soil fauna. The wastes contain toxic compounds such as metals or hydrocarbons, which tend to accumulate in the living. In the research, earthworms were used u as bio-indicators of soil pollution resulting from the presence of pollution contained in drilling waste. The aim of this study is to evaluation of toxicity of the waste of spent oil and water drilling cuttings to earthworm Eisenia fetida. Oil-based and water-based drilling cuttings were added to soil, used six doses of drilling wastes (5%, 10%, 15%, 25%, 30%, 50%. The results showed that the 45 days LC50 of oil-based drilling cuttings ranged 18%, LC50 of water-based drilling cuttings ranged 33%. In general, mortality increases with increasing dosage waste.

Australians are not equally protected from industrial air pollution

International Nuclear Information System (INIS)

Dobbie, B; Green, D

2015-01-01

Australian air pollution standards are set at national and state levels for a number of chemicals harmful to human health. However, these standards do not need to be met when ad hoc pollution licences are issued by state environment agencies. This situation results in a highly unequal distribution of air pollution between towns and cities, and across the country. This paper examines these pollution regulations through two case studies, specifically considering the ability of the regulatory regime to protect human health from lead and sulphur dioxide pollution in the communities located around smelters. It also considers how the proposed National Clean Air Agreement, once enacted, might serve to reduce this pollution equity problem. Through the case studies we show that there are at least three discrete concerns relating to the current licencing system. They are: non-onerous emission thresholds for polluting industry; temporal averaging thresholds masking emission spikes; and ineffective penalties for breaching licence agreements. In conclusion, we propose a set of new, legally-binding national minimum standards for industrial air pollutants must be developed and enforced, which can only be modified by more (not less) stringent state licence arrangements. (letter)

Technological Proposals for Recycling Industrial Wastes for Environmental Applications

Directory of Open Access Journals (Sweden)

Isabel Romero-Hermida

2014-08-01

Full Text Available A two-fold objective is proposed for this research: removing hazardous and unpleasant wastes and mitigating the emissions of green house gasses in the atmosphere. Thus, the first aim of this work is to identify, characterize and recycle industrial wastes with high contents of calcium or sodium. This involves synthesizing materials with the ability for CO2 sequestration as preliminary work for designing industrial processes, which involve a reduction of CO2 emissions. In this regard, phosphogypsum from the fertilizer industry and liquid wastes from the green olive and bauxite industries have been considered as precursors. Following a very simple procedure, Ca-bearing phosphogypsum wastes are mixed with Na-bearing liquid wastes in order to obtain a harmless liquid phase and an active solid phase, which may act as a carbon sequestration agent. In this way, wastes, which are unable to fix CO2 by themselves, can be successfully turned into effective CO2 sinks. The CO2 sequestration efficiency and the CO2 fixation power of the procedure based on these wastes are assessed.

Polyester Apparel Cutting Waste as Insulation Material

OpenAIRE

Trajković, Dušan; Jordeva, Sonja; Tomovska, Elena; Zafirova, Koleta

2017-01-01

Polyester waste is the dominant component of the clothing industry waste stream, yet its recycling in this industry is rarely addressed. This paper proposes using polyester cutting waste as an insulation blanket for roofing and buildings’ internal walls in order to reduce environmental pollution. The designed textile structures used waste cuttings from different polyester fabrics without opening the fabric to fibre. Thermal insulation, acoustic insulation, fire resistance and biodegradation o...

Pollution prevention/waste minimization program 1998 fiscal year work plan - WBS 1.11.2.1

International Nuclear Information System (INIS)

Howald, S.C.; Merry, D.S.

1997-09-01

Pollution Prevention/Waste Minimization (P2/WMin) is the Department of Energy's preferred approach to environmental management. The P2/WMin mission is to eliminate or minimize waste generation, pollutant releases to the environment, use of toxic substances, and to conserve resources by implementing cost-effective pollution prevention technologies, practices, and polices

Intake fractions of industrial air pollutants in China. Estimation and application

International Nuclear Information System (INIS)

Wang, Shuxiao; Hao, Jiming; Li, Ji; Lu, Yongqi; Ho, Mun S.

2006-01-01

Intake fractions, an emissions-intake relationship for primary pollutants, are defined and are estimated in order to make simple estimates of health damages from air pollution. The sulfur dioxide (SO 2 ) and total suspended particles (TSP) intake fractions for five cities of China are estimated for the four main polluting industries-electric power generation, mineral (mostly cement) products industry, chemical process industry and metallurgical industry (mainly iron and steel smelting). The Industrial Source Complex Long Term (ISTLT3) model is used to simulate the spatial distribution of incremental ambient concentrations due to emissions from a large sample of site-specific sources. Detailed population distribution information is used for each city. The average intake fractions within 50 km of these sources are 4.4x10 -6 for TSP, and 4.2x10 -6 for SO 2 , with standard deviations of 8.15x10 -6 and 9.16x10 -6 , respectively. They vary over a wide range, from 10 -7 to 10 -5 . Although the electric power generation has been the focus of much of the air pollution research in China, our results show that it has the lowest average intake fraction for a local range among the four industries, which highlights the importance of pollutant emissions from other industrial sources. Sensitivity analyses show how the intake fractions are affected by the source and pollutant characteristics, the most important parameter being the size of the domain. However, the intake fraction estimates are robust enough to be useful for evaluating the local impacts on human health of primary SO 2 and TSP emissions. An application of intake fractions is given to demonstrate how this approach provides a rapid population risk estimate if the dose-response function is linear without threshold, and hence can help in prioritizing pollution control efforts. (author)

Pollution prevention: The new environmental ethic

International Nuclear Information System (INIS)

Breen, J.J.; Dellarco, M.J.

1991-01-01

EPA is embarking on a new major environmental policy initiative: pollution prevention. It obviates the short-comings of end-of-pipe regulations and fosters efforts for industry to modify production practices to prevent pollution. For its part, the Agency has adopted this initiative in research and development, regulatory program development, and technology transfer activities. Research and Development programs are being established to address chemical substitution, reductions in chemical usage, product life cycles, and recycling. Regulatory programs are incorporating pollution prevention in major strategies of product stewardship and hazardous waste management. Technology transfer activities are designed to inform and educate industry and the public through Agency sponsored programs with the Pollution Prevention Information Center and the American Pollution Prevention Institute

An Innovative Partnership Approach for Environmental Management and Pollution Prevention.

Science.gov (United States)

Erten-Unal, Mujde; Aydlett, Guy M.

1997-01-01

A partnership between a university and a government regulatory agency sought to assist industries with pollution prevention and waste management. Economic incentives were developed to promote waste minimization. (SK)

Radioactive waste management in the VS military nuclear industry

International Nuclear Information System (INIS)

Kobal'chuk, O.V.; Kruglov, A.K.; Sokolova, I.D.; Smirnov, Yu.V.

1989-01-01

Organization and plans of radioactive waste management in the US military nuclear industry, determining transition from the policy of temporal waste storage to their final and safe disposal are presented. Programs of long-term management of high-level, transuranium and low-level wastes, the problems of the work financing and the structure of management activities related to the radioactive waste processing military nuclear industry enterprises are considered

Air pollution and economics: Alternate use of fuels in small scale industries

International Nuclear Information System (INIS)

Rao, B.P.S.; Pandit, V.I.

1999-01-01

In developing countries the problem of air pollution was recognized earlier, however, it has acquired a greater dimension due to the conventional use of low grade fuels like coal, baggase, rice husk, etc. having high sulphur and ash content. The industrial sources contribute about 30--40% of the total emissions. In India, the small scale industries (low investment group) contribute about 60--80% of the total industrial emissions. These industries are characterized with various environmental pollution problems due to cluster of small scale industries located in sensitive area; use of low grade fuel, primitive processing techniques without emission abatement facilities etc., thus leading to enormous pollution in an confined region. Acute need was felt to reduce the pollution problem associated with small scale industries by use of cleaner fuel so as to reduce the localized problem. The paper presents the emissions associated with use of coal/coke, natural gas, LPG, and propane along with the fuel cost for small scale industrial sector of Agra, Firozabad and Mathura region. The studies carried out would find applicability to meet the air pollution standards based on shift in fuel and associated cost

Radioactive wastes in the air

International Nuclear Information System (INIS)

1968-01-01

Methods of preventing the pollution of air by radioactive waste from atomic centres were discussed in an Agency Symposium held in New York at the end of August. It was agreed that the atomic industry has a good safety record, and suggestions were made that there should now be a concerted effort to prevent air pollution by all industries. (author)

Environmental impacts of waste management in the hospitality industry: Creating a waste management plan for Bergvik Kartano

OpenAIRE

Adigwe, Christopher

2014-01-01

Many hospitality industries find it difficult to control or manage solid wastes, such as food, containers, paper, cardboard and scrap metals, which are waste generated on a daily basis depending on the industry. Most hospitality industries tend to lag behind when it comes to the collection of waste. Only a fraction of the¬¬ waste collected receives proper disposal. When waste is not collected sufficiently and the disposal is inappropriate the waste can accumulate and cause water, land and air...

40 CFR 63.1213 - How can the compliance date be extended to install pollution prevention or waste minimization...

Science.gov (United States)

2010-07-01

... to install pollution prevention or waste minimization controls? 63.1213 Section 63.1213 Protection of... pollution prevention or waste minimization controls? (a) Applicability. You may request from the... must contain the following information: (i) A description of pollution prevention or waste minimization...

How the environmental community views the mining industry

International Nuclear Information System (INIS)

Maest, A.

1990-01-01

Working with the Environmental Mining Network, a coalition of ∼75 environmental groups nationwide formed to encourage environmentally-sound hard-rock mining. Emphasis is on changing the industrial process so that wastes are not created in the first place, instead of creating the wastes and dealing with them as an afterthought. The tradition of pollution control is slowly being replaced with prevention. Objectives of pollution prevention for mining include: Reduction of the volume of material extracted, beneficiated, processed, and removed for exploration by improving techniques for these processes, mining less, and encouraging remining and use of scrap materials; Reduction of the toxicity and environmental impact of wastes that are nonetheless generated by employing techniques that minimize the release of contaminants to the environment; Identifying current and developing technologies for pollution prevention in the mining industry and distribute this among the regulated community. Pollution prevention should be incorporated in design and performance standards. Assessment and demonstration of pollution prevention should be part of the permit application. Implementation of serious non-rhetorical pollution prevention by the mining industry has the potential to give miners and environmentalists a common ground and common goals where we could truely be in a win-win situation in terms of encouraging both environmental and economic robustness

Informal e-waste recycling: environmental risk assessment of heavy metal contamination in Mandoli industrial area, Delhi, India.

Science.gov (United States)

Pradhan, Jatindra Kumar; Kumar, Sudhir

2014-01-01

Nowadays, e-waste is a major source of environmental problems and opportunities due to presence of hazardous elements and precious metals. This study was aimed to evaluate the pollution risk of heavy metal contamination by informal recycling of e-waste. Environmental risk assessment was determined using multivariate statistical analysis, index of geoaccumulation, enrichment factor, contamination factor, degree of contamination and pollution load index by analysing heavy metals in surface soils, plants and groundwater samples collected from and around informal recycling workshops in Mandoli industrial area, Delhi, India. Concentrations of heavy metals like As (17.08 mg/kg), Cd (1.29 mg/kg), Cu (115.50 mg/kg), Pb (2,645.31 mg/kg), Se (12.67 mg/kg) and Zn (776.84 mg/kg) were higher in surface soils of e-waste recycling areas compared to those in reference site. Level exceeded the values suggested by the US Environmental Protection Agency (EPA). High accumulations of heavy metals were also observed in the native plant samples (Cynodon dactylon) of e-waste recycling areas. The groundwater samples collected form recycling area had high heavy metal concentrations as compared to permissible limit of Indian Standards and maximum allowable limit of WHO guidelines for drinking water. Multivariate analysis and risk assessment studies based on total metal content explains the clear-cut differences among sampling sites and a strong evidence of heavy metal pollution because of informal recycling of e-waste. This study put forward that prolonged informal recycling of e-waste may accumulate high concentration of heavy metals in surface soils, plants and groundwater, which will be a matter of concern for both environmental and occupational hazards. This warrants an immediate need of remedial measures to reduce the heavy metal contamination of e-waste recycling sites.

Characterization of industrial process waste heat and input heat streams

Energy Technology Data Exchange (ETDEWEB)

Wilfert, G.L.; Huber, H.B.; Dodge, R.E.; Garrett-Price, B.A.; Fassbender, L.L.; Griffin, E.A.; Brown, D.R.; Moore, N.L.

1984-05-01

The nature and extent of industrial waste heat associated with the manufacturing sector of the US economy are identified. Industry energy information is reviewed and the energy content in waste heat streams emanating from 108 energy-intensive industrial processes is estimated. Generic types of process equipment are identified and the energy content in gaseous, liquid, and steam waste streams emanating from this equipment is evaluated. Matchups between the energy content of waste heat streams and candidate uses are identified. The resultant matrix identifies 256 source/sink (waste heat/candidate input heat) temperature combinations. (MHR)

Lead Polluted Hotspot: Environmental Implication of Unplanned Industrial Development

Directory of Open Access Journals (Sweden)

Rikta Sharmin Yousuf

2016-06-01

Full Text Available In Rayer Bazaar, different industries like tannery, plastic, textile, battery recycling industry etc. are increasing rapidly without considering the environmental issues and deterioration. Since chromium (Cr pollution of this area has been widely investigated due to the presence of tannery industries, this study was focused on examining other environmental factors. Field visits and analytical results of semi-quantitative and quantitative analysis as well as three dimensional excitation emission matrix spectroscopy (3DEEM of water, soil and vegetative tissues indicated that, the area is highly polluted in term of different environmental parameters and metal content. The extremely high lead (Pb content of the soil (1171.7 mg/kg in summer, 2157.1 mg/kg in winter and blackish materials of vegetative tissues (6585.6 mg/kg in summer, 1974.1 mg/kg in winter indicates excessive lead deposition of this area that makes it a lead polluted hotspot. One of the possible sources of the extremely high lead concentration is adjacent battery recycling industry and/or other industries surrounding this area. So it is urgent to take necessary steps to find out immediate options for possible mitigation.

Challenges of E-Waste pollution to soil environments in Nigeria - A ...

African Journals Online (AJOL)

Challenges of E-Waste pollution to soil environments in Nigeria - A Review. ... of ewaste on the environment (including the soil fauna and flora) especially in Nigeria. ... Possible e-waste management strategies will also be highlighted on soil ...

Pediatric asthma and ambient pollutant levels in industrializing nations.

Science.gov (United States)

Jassal, Mandeep S

2015-01-01

Asthma is one of the most common chronic diseases in childhood and its prevalence has been increasing within industrializing nations. The contribution of ambient pollutants to asthma symptomatology has been explored in some countries through epidemiological investigations, molecular analysis and monitoring functional outcomes. The health effects of rising environmental pollution have been of increasing concern in industrializing nations with rising urbanization patterns. This review article provides an overview of the link between pediatric asthma and exposure to rising sources of urban air pollution. It primarily focuses on the asthma-specific effects of sulfur dioxide, nitrogen dioxide, ozone and particulate matter. Worldwide trends of asthma prevalence are also provided which detail the prominent rise in asthma symptoms in many urban areas of Africa, Latin America and Asia. The molecular and functional correlation of ambient pollutants with asthma-specific airway inflammation in the pediatric population are also highlighted. The final aspect of the review considers the correlation of motor vehicle, industrial and cooking energy sources, ascribed as the major emitters among the pollutants in urban settings, with asthma epidemiology in children. © The Author 2014. Published by Oxford University Press on behalf of Royal Society of Tropical Medicine and Hygiene. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

[Pollution-ecological problems of old industrial and mining areas and future research prospects].

Science.gov (United States)

Zhou, Qixing

2005-06-01

Environmental pollution and its solicitation in ecological problems of old industrial and mining areas have become a worldwide technological puzzle restricting sustainable economic and social development. But, the definition and category of old industrial and mining areas is still disputed as an important concept. In this paper, the concept of old industrial and mining area was discussed in theory, and, proceeded with analyzing the complexity of current situation and environmental pollution problems of old industrial and mining areas in China, more keystone attention was paid to the secondary pollution problems from old industrial and mining areas as an important frontier of science. On the basis of expounding the complexity and characters of environmental pollution in old industrial and mining areas, it was suggested that as two key scientific problems in environmental sciences and ecology, the formation mechanisms and control technology of secondary pollution in old industrial and mining areas and the responses of new-type diseases to environmental pollution based on molecular ecotoxicology should be systematically studied on the national scale, and be an important component of environmental protection strategy in China in the future.

Full report: Assessment and opportunity identification of energy efficient pollution prevention technologies and processes

Energy Technology Data Exchange (ETDEWEB)

1994-11-01

US industry produces about 12 billion tons of waste a year, or two-thirds of the waste generated in the US. The costs of handling and disposing of these wastes are significant, estimated to be between $25 and $43 billion in 1991, and represent an increase of 66% since 1986. US industry also uses about one-third of all energy consumed in the nation, which adds to the environmental burden. Industrial wastes affect the environmental well-being of the nation and, because of their growing costs, the competitive abilities of US industry. As part of a national effort to reduce industrial wastes, the US Congress passed the Energy Policy Act (EPAct, P.L. 102-486). Section 2108, subsections (b) and (c), of EPAct requires the Department of Energy (DOE) to identify opportunities to demonstrate energy efficient pollution prevention technologies and processes; to assess their availability and the energy, environmental, and cost effects of such technologies; and to report the results. Work for this report clearly pointed to two things, that there is insufficient data on wastes and that there is great breadth and diversity in the US industrial sector. This report identifies: information currently available on industrial sector waste streams, opportunities for demonstration of energy efficient pollution prevention technologies in two industries that produce significant amounts of waste--chemicals and petroleum, characteristics of waste reducing and energy saving technologies identifiable in the public literature, and potential barriers to adoption of waste reducing technologies by industry.

Australia’s first national level quantitative environmental justice assessment of industrial air pollution

International Nuclear Information System (INIS)

Chakraborty, Jayajit; Green, Donna

2014-01-01

This study presents the first national level quantitative environmental justice assessment of industrial air pollution in Australia. Specifically, our analysis links the spatial distribution of sites and emissions associated with industrial pollution sources derived from the National Pollution Inventory, to Indigenous status and social disadvantage characteristics of communities derived from Australian Bureau of Statistics indicators. Our results reveal a clear national pattern of environmental injustice based on the locations of industrial pollution sources, as well as volume, and toxicity of air pollution released at these locations. Communities with the highest number of polluting sites, emission volume, and toxicity-weighted air emissions indicate significantly greater proportions of Indigenous population and higher levels of socio-economic disadvantage. The quantities and toxicities of industrial air pollution are particularly higher in communities with the lowest levels of educational attainment and occupational status. These findings emphasize the need for more detailed analysis in specific regions and communities where socially disadvantaged groups are disproportionately impacted by industrial air pollution. Our empirical findings also underscore the growing necessity to incorporate environmental justice considerations in environmental planning and policy-making in Australia. (paper)

Recovery of uranium and accompanying metals from various types of industrial wastes

International Nuclear Information System (INIS)

Chajduk, E.; Danko, B.; Gajda, D.; Zakrzewska, G.; Harasimowicz, M.; Bieluszka, P.

2014-01-01

On January 28"t"h 2014 the Program of Polish Nuclear Energy was signed by Polish Government. According to this program Poland has to secure a constant supply of uranium for Polish NPPs in the future. Uranium in Poland occurs in Vistula Spit area in sandstone rocks and Podlasie Depression area in black dictyonema shales, which are low grade ores. Scarce uranium resources stimulate interest in its recovery from secondary resources as potential raw materials. Industrial wastes and by-products were considered as a source of uranium in this studies. Apart from uranium other valuable metals (e.g. vanadium, molybdenum or lanthanides) were recovered to improve the economy of the process. Three types of industrial wastes were examined: flotation tailings from the copper industry, phosphoric acid from the fertilizer industry and fracturing fluid from shale gas exploitation. Metals from flotation tailings were separated in two steps: 1) acidic leaching of the flotation waste using sulfuric acid solution and 2) separation of metals by ion-exchange chromatography. All the liquid samples were analyzed by ICP-MS method to determine the separation efficiency of the process. Uranium was recovered from phosphoric acid by high-pressure membrane filtration or by extraction/stripping integrated processes applying membrane modules Liquid-Cel® Extra-Flow (Celgard). Aqueous solutions after hydraulic fracturing are very diverse in terms of chemical composition, depending on borehole and fracturing technology applied. The content of various substances in backflow fluid depends on mechanical behavior and chemical composition of shale. Organic matter content in this type of waste did not exceed 1% usually, but the salinity is high. Initially, organic pollutants were removed and next the fluid was purified by combined various ion-exchangers. Individual metals were selectively eluted from ion-exchanger by combination of different eluents. The content of metals in samples was analyzed by ICP

Comprehensive review on toxicity of persistent organic pollutants from petroleum refinery waste and their degradation by microorganisms.

Science.gov (United States)

Varjani, Sunita J; Gnansounou, Edgard; Pandey, Ashok

2017-12-01

Control and prevention of environmental pollution has become a worldwide issue of concern. Aromatic hydrocarbons including benzene, toluene, ethyl benzene, xylene (BTEX) and polyaromatic hydrocarbons (PAHs) are persistent organic pollutants (POPs), released into the environment mainly by exploration activities of petroleum industry. These pollutants are mutagenic, carcinogenic, immunotoxic and teratogenic to lower and higher forms of life i.e. microorganisms to humans. According to the International Agency for Research on Cancer (IARC) and United States Environmental Protection Agency (U.S. EPA), Benzo[a]pyrene (BaP) is carcinogenic in laboratory animals and humans. Aromatic hydrocarbons are highly lipid soluble and thus readily absorbed from environment in gastrointestinal tract of mammals. Treatment and remediation of petroleum refinery waste have been shown either to reduce or to eliminate genotoxicity of these pollutants. Bioremediation by using microorganisms to treat this waste is showing a promising technology as it is safe and cost-effective option among various technologies tested. The main aim of this review is to provide contemporary information on variety of aromatic hydrocarbons present in crude oil (with special focus to mono- and poly-aromatic hydrocarbons), exposure routes and their adverse effects on humans. This review also provides a synthesis of scientific literature on remediation technologies available for aromatic hydrocarbons, knowledge gaps and future research developments in this field. Copyright © 2017 Elsevier Ltd. All rights reserved.

Direct method for impact assessment of environmental pollutants and toxicants causing health hazards

International Nuclear Information System (INIS)

Fazal-ur-Rehman; Adil, A.; Abdullah, A.; Masood, S.R.; Agha, A.

1997-01-01

Industrial waste pollutants and toxicants are released in three forms i.e. gas, liquid, solid or their admixtures, causing atmospheric , hydro spheric and lithospheric pollutions. Gaseous wastes pollute the surrounding air before entering the waste-cycle and bio-cycle through vegetation/ forestation(i.e., plant kingdom). Liquid wastes enter the water-cycle directly and speedily whereas solid wastes enter the water-cycle indirectly and slowly. All these wastes, as it is well known later on enter plant and animal kingdoms which ultimately effect the human health and make different body parts sick/malignant. Therefore, the regular monitoring of elemental composition of these body parts becomes imperative. The above mentioned format of impact assessment has been followed during different joint studies (carried out in collaboration with university of the Punjab, INMOL and other Departments) which are based on the analytical data collected during the period of last five years. These samples include specimens of blood serum, cancer tissues, drinking and running water, industrial wastes and effluents etc. The comparison, of analysis of samples of unaffected (healthy) and malignant body parts, leads to the direct assessment of environmental pollutants and the inhabitants. (author)

Annual report of waste generation and pollution prevention progress 2000 [USDOE] [9th edition

International Nuclear Information System (INIS)

None

2001-01-01

This ninth edition of the Annual Report of Waste Generation and Pollution Prevention Progress highlights waste reduction, pollution prevention accomplishments, and cost savings/avoidance for the U.S. Department of Energy (DOE) Pollution Prevention Program for Fiscal Year 2000. This edition marks the first time that progress toward meeting the 2005 Pollution Prevention Goals, issued by the Secretary of Energy in November 1999, is being reported. In addition, the Annual Report has a new format, and now contains information on a fiscal year basis, which is consistent with other DOE reports

Cyanobacterial flora from polluted industrial effluents.

Science.gov (United States)

Parikh, Amit; Shah, Vishal; Madamwar, Datta

2006-05-01

Effluents originating from pesticides, agro-chemicals, textile dyes and dyestuffs industries are always associated with high turbidity, colour, nutrient load, and heavy metals, toxic and persistent compounds. But even with such an anthropogenic nature, these effluents contain dynamic cyanobacterial communities. Documentation of cyanobacterial cultures along the water channels of effluents discharged by above mentioned industries along the west coast of India and their relationship with water quality is reported in this study. Intensity of pollution was evaluated by physico-chemical analysis of water. Higher load of solids, carbon and nutrients were found to be persistent throughout the analysis. Sediment and water samples were found to be colored in nature. Cyanobacterial community structure was found to be influenced by the anthropogenic pollution. 40 different cyanobacterial species were recorded from 14 genera of 5 families and an elevated occurrence of Phormidium, Oscillatoria and Chroococcus genera was observed in all the sampling sites.

Pollution Prevention Program: Technology summary

International Nuclear Information System (INIS)

1994-02-01

The Department of Energy (DOE) has established a national Research, Development, Demonstration, Testing, and Evaluation (RDDT ampersand E) Program for pollution prevention and waste minimization at its production plants During FY89/90 the Office of Environmental Restoration and Waste Management (EM), through the Office of Technology Development (OTD), established comprehensive, pollution prevention technical support programs to demonstrate new, environmentally-conscious technology for production processes. The RDDT ampersand E program now entails collaborative efforts across DOE. The Pollution Prevention Program is currently supporting three major activities: The DOE/US Air Force Memorandum of Understanding Program is a collaborative effort to utilize the combined resources of DOE and the Department of Defense, eliminate duplication of effort in developing technologies, and to facilitate technology solutions aimed at reducing waste through process modification, material substitution or recycling. The Waste Component Recycle, Treatment and Disposal Integrated Demonstration (WeDID) will develop recycle, treatment, and disposal processes and associated technologies for use in the dismantlement of non-nuclear weapons components, to support US arms treaties and policies. This program will focus on meeting all security and regulatory requirements (with additional benefit to the commercial electronics industry). The Environmentally Conscious Manufacturing Integrated Demonstration (ECMID) will effectively implement ECM technologies that address both the needs of the DOE Complex and US electronics industry, and encourage strong interaction between DOE and US industry. The ECMID will also develop life cycle analysis tools that will aid decisionmakers in selecting the optimum process based on the tradeoffs between cost an environmental impact

Bioremediation of Industrial Waste Through Enzyme Producing Marine Microorganisms.

Science.gov (United States)

Sivaperumal, P; Kamala, K; Rajaram, R

Bioremediation process using microorganisms is a kind of nature-friendly and cost-effective clean green technology. Recently, biodegradation of industrial wastes using enzymes from marine microorganisms has been reported worldwide. The prospectus research activity in remediation area would contribute toward the development of advanced bioprocess technology. To minimize industrial wastes, marine enzymes could constitute a novel alternative in terms of waste treatment. Nowadays, the evidence on the mechanisms of bioremediation-related enzymes from marine microorganisms has been extensively studied. This review also will provide information about enzymes from various marine microorganisms and their complexity in the biodegradation of comprehensive range of industrial wastes. © 2017 Elsevier Inc. All rights reserved.

Toxic potency and effects of diffuse air pollution

NARCIS (Netherlands)

Hamers, T.H.M.

2002-01-01

Diffuse air pollution consists of an omnipresent complex mixture of pollutants that is emitted from many widely dispersed sources as traffic, industries, households, energy plants, waste incinerators, and agriculture. It can be deposited in relatively remote areas as a result of

Annual report of waste generation and pollution prevention progress 1998; ANNUAL

International Nuclear Information System (INIS)

NONE

1999-01-01

This seventh Annual Report presents and analyzes DOE Complex-wide waste generation and pollution prevention activities at 45 reporting sites from 1993 through 1998. This section summarizes Calendar Year 1998 Complex-wide waste generation and pollution prevention accomplishments. More detailed information follows this section in the body of the Report. In May 1996, the Secretary of Energy established a 50 percent Complex-Wide Waste Reduction Goal (relative to the 1993 baseline) for routine operations radioactive, mixed, and hazardous waste generation, to be achieved by December31, 1999. DOE has achieved its Complex-Wide Waste Reduction Goals for routine operations based upon a comparison of 1998 waste generation to the 1993 baseline. Excluding sanitary waste, routine operations waste generation decreased 67 percent overall from 1993 to 1998. However, for the first time since 1994, the total amount of materials recycled by the Complex decreased from 109,600 metric tons in 1997 to 92,800 metric tons in 1998. This decrease is attributed to the fact that in 1997, several large ''one-time only'' recycling projects were conducted throughout the Complex. In order to demonstrate commitment to DOE's Complex-wide recycling goal, it is important for sites to identify all potential large-scale recycling/reuse opportunities

Promoting low-carbon city through industrial symbiosis: A case in China by applying HPIMO model

International Nuclear Information System (INIS)

Dong, Liang; Fujita, Tsuyoshi; Zhang, Hui; Dai, Ming; Fujii, Minoru; Ohnishi, Satoshi; Geng, Yong; Liu, Zhu

2013-01-01

China launched low-carbon city strategy to respond global climate change. Industrial symbiosis (IS) could generate both economic and environmental benefits in clustered industries and communities. This research shed light on how industrial symbiosis contributes to city's low-carbon development. An urban-level hybrid physical input and monetary output (HPIMO) model which covers physical energy inputs and air pollutants emissions, is established for addressing case study in a Chinese typical industrial city (Liuzhou). Based on current energy consumption and industrial symbiosis and the application of HPIMO model, scenarios related to industrial symbiosis, including waste plastics recycling, scrap tires recycling, flying ash recycling and biomass utilization are explored. Results show that compared with business-as-usual (BAU) scenario, IS can reduce solid wastes and further contribute to the co-benefits of energy saving, CO 2 emissions reduction and air pollutants reduction. The finding is critical for national low-carbon strategy. Finally, policy implications to support the ever-improvement of IS promotion in China are proposed and discussed. - Highlights: • Industrial symbiosis could contribute to low-carbon city in terms of co-benefit. • Co-benefit of IS was in terms of waste reduction and air pollutants reduction. • Waste plastics recycling and biomass utilization generated large co-benefit. • Coal fly ash recycling reduced the solid waste while increased air pollutants. • The prices of wastes and facilities investment affected the total cost-benefit

Management of radioactive waste of scientific and industrial centers

International Nuclear Information System (INIS)

Sobolev, I.A.; Dmitriev, S.A.; Barinov, A.S.; Ojovan, M.I.; Timofeev, E.M.

1995-01-01

Available for the time being in the Russian Federation, a system of management of institutional and industrial radioactive waste (e.g. radioactive waste from industry, medicine, scientific organizations and other, which are not related to the nuclear fuel cycle or defense) provides for its collection, transportation, storage, treatment, immobilization and disposal by a network of special enterprises. Russia has 16 such enterprises. Moscow Scientific and Industrial Association Radon deals with the problems of radioactive waste from Central European part of Russia, which includes Moscow, Moscow Region and also Tverskaya, Yaroslavskaya, Vladimirskaya, Kostromskaya, Kaluzhskaya, Bryanskaya, Smolenskaya, Tulskaya, Ryazanskaya regions. The population of the central part of Russia constitutes about 40 million people. At the same time about 80% of the radioactive waste, which is collected for treatment and disposal from the territory of Russia, is included in this region. The average volume of the waste to be treated at SIA Radon is 3,000 m 3 per year for solid waste and 350 m 3 per year for liquid waste. Total radioactivity of processed waste is up to 4 PBq per year

Solid wastes research in South Africa

CSIR Research Space (South Africa)

Noble, RG

1976-06-01

Full Text Available The importance of solid wastes management in environmental pollution control cannot be over-emphasised. Increased socio-economic development in South Africa has brought with it increasing volumes of urban, industrial and agricultural wastes...

Decolorization of Industrial Waste Using Fenton Process and Photo Fenton

OpenAIRE

Wardiyati, Siti; Dewi, Sari Hasnah; Fisli, Adel

2013-01-01

Industrial waste water decolorization has been done using the method of Fenton and Photo Fenton. The experiment was conducted in order to obtain the optimum process conditions for industrial waste treatment method with Fenton and Photo Fenton. Industrial waste used in this experiment waste of blue batik making process derived from Rara Djograng Batik Yogyakarta. Factors were studied in this research are the effect of the amount of catalyst FeSO4.7H2O, the amount of oxidant H2O2, and the time ...

2011 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

Energy Technology Data Exchange (ETDEWEB)

David Frederick

2012-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (LA-000160-01), for the wastewater reuse site at the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2010 through October 31, 2011. The report contains the following information: (1) Facility and system description; (2) Permit required effluent monitoring data and loading rates; (3) Groundwater monitoring data; (4) Status of special compliance conditions; and (5) Discussion of the facility's environmental impacts. During the 2011 reporting year, an estimated 6.99 million gallons of wastewater were discharged to the Industrial Waste Ditch and Pond which is well below the permit limit of 13 million gallons per year. Using the dissolved iron data, the concentrations of all permit-required analytes in the samples from the down gradient monitoring wells were below the Ground Water Quality Rule Primary and Secondary Constituent Standards.

Industrial management of radioactive wastes

International Nuclear Information System (INIS)

Lavie, J.M.

1984-01-01

This article deals with the present situation in France concerning radioactive waste management. For the short and medium term, that is to say processing and disposal of low and medium level radioactive wastes, there are industrial processes giving all the guarantees for a safe containment, but improvements are possible. For the long term optimization of solution requires more studies of geologic formations. Realization emergency comes less from the waste production than the need to optimize the disposal techniques. An international cooperation exists. All this should convince the public opinion and should develop planning and realization [fr

Phytoremediation of Industrial and Pharmaceutical Pollutants

Directory of Open Access Journals (Sweden)

Swarna Shikha

2016-10-01

Full Text Available Pollution in water bodies and soil is a major and ever-increasing environmental issue nowadays, and most conventional remediation approaches do not provide appropriate solutions. The contamination of soil is a major concern for the environment and needs to be remediated. These pollutants include complex organic compounds, heavy metals released from industries and plants and natural products such as oils from accidental release. Further the nature of pollution will be governed by the source and type of the contaminant, and other inorganic compounds are released into the environment from a number of sources like mining, smelting, electroplating, and farming. Plants can clean up many types of contaminants like metals, pesticides, oils, and explosives. Phytoremediation is emerging as a bio-based and low-cost alternative in the cleanup of heavy metal-contaminated soils.

Good Practice Guide Waste Minimization/Pollution Prevention; TOPICAL

International Nuclear Information System (INIS)

J Dorsey

1999-01-01

This Good Practice Guide provides tools, information, and examples for promoting the implementation of pollution prevention during the design phases of U.S. Department of Energy (DOE) projects. It is one of several Guides for implementing DOE Order 430.1, Life-cycle Asset Management. DOE Order 430.1 provides requirements for DOE, in partnership with its contractors, to plan, acquire, operate, maintain, and dispose of physical assets. The goals of designing for pollution prevention are to minimize raw material consumption, energy consumption, waste generation, health and safety impacts, and ecological degradation over the entire life of the facility (EPA 1993a). Users of this Guide will learn to translate national policy and regulatory requirements for pollution prevention into action at the project level. The Guide was written to be applicable to all DOE projects, regardless of project size or design phase. Users are expected to interpret the Guide for their individual project's circumstances, applying a graded approach so that the effort is consistent with the anticipated waste generation and resource consumption of the physical asset. This Guide employs a combination of pollution prevention opportunity assessment (PPOA) methods and design for environment (DfE) philosophies. The PPOA process was primarily developed for existing products, processes, and facilities. The PPOA process has been modified in this Guide to address the circumstances of the DOE design process as delineated in DOE Order 430.1 and its associated Good Practice Guides. This modified form of the PPOA is termed the Pollution Prevention Design Assessment (P2DA). Information on current nationwide methods and successes in designing for the environment also have been reviewed and are integrated into this guidance

Guides to pollution prevention: Selected hospital waste streams

International Nuclear Information System (INIS)

1990-06-01

The hazardous wastes generated by general medical and surgical hospitals are small in volume relative to those of industrial facilities; however, the wastes are of a wide variety. Some of the hazardous materials used by hospitals that become part of their waste streams include chemotherapy and antineoplastic chemicals, solvents, formaldehyde, photographic chemicals, radionuclides, mercury, waste anesthetic gases; and other toxic, corrosive and miscellaneous chemicals. Additional wastes such as infectious waste, incinerator exhaust, laundry-related waste, utility wastes, and trash were not addressed in the guide. Reducing the generation of these materials at the source, or recycling the wastes on- or off-site, will benefit hospitals by reducing disposal costs and lowering the liabilities associated with hazardous waste disposal. The guide provides an overview of hospital waste generating processes and presents options for minimizing waste generation through source reduction and recycling

An industrial ecology approach to municipal solid waste ...

Science.gov (United States)

Municipal solid waste (MSW) can be viewed as a feedstock for industrial ecology inspired conversions of wastes to valuable products and energy. The industrial ecology principle of symbiotic processes using waste streams for creating value-added products is applied to MSW, with examples suggested for various residual streams. A methodology is presented to consider individual waste-to-energy or waste-to-product system synergies, evaluating the economic and environmental issues associated with each system. Steps included in the methodology include identifying waste streams, specific waste components of interest, and conversion technologies, plus steps for determining the economic and environmental effects of using wastes and changes due to transport, administrative handling, and processing. In addition to presenting the methodology, technologies for various MSW input streams are categorized as commercialized or demonstrated to provide organizations that are considering processes for MSW with summarized information. The organization can also follow the methodology to analyze interesting processes. Presents information useful for analyzing the sustainability of alternatives for the management of municipal solid waste.

Laboratory scale studies on removal of chromium from industrial wastes.

Science.gov (United States)

Baig, M A; Mir, Mohsin; Murtaza, Shazad; Bhatti, Zafar I

2003-05-01

Chromium being one of the major toxic pollutants is discharged from electroplating and chrome tanning processes and is also found in the effluents of dyes, paint pigments, manufacturing units etc. Chromium exists in aqueous systems in both trivalent (Cr(3+)) and hexavalent (Cr(6+)) forms. The hexavalent form is carcinogenic and toxic to aquatic life, whereas Cr(3+) is however comparatively less toxic. This study was undertaken to investigate the total chromium removal from industrial effluents by chemical means in order to achieve the Pakistan NEQS level of 1 mg/L by the methods of reduction and precipitation. The study was conducted in four phases. In phase I, the optimum pH and cost effective reducing agent among the four popular commercial chemicals was selected. As a result, pH of 2 was found to be most suitable and sodium meta bisulfate was found to be the most cost effective reducing agent respectively. Phase II showed that lower dose of sodium meta bisulfate was sufficient to obtain 100% efficiency in reducing Cr(6+) to Cr(3+), and it was noted that reaction time had no significance in the whole process. A design curve for reduction process was established which can act as a tool for treatment of industrial effluents. Phase III studies indicated the best pH was 8.5 for precipitation of Cr(3+) to chromium hydroxide by using lime. An efficiency of 100% was achievable and a settling time of 30 minutes produced clear effluent. Finally in Phase IV actual waste samples from chrome tanning and electroplating industries, when precipitated at pH of 12 gave 100% efficiency at a settling time of 30 minutes and confined that chemical means of reduction and precipitation is a feasible and viable solution for treating chromium wastes from industries.

The contamination of an environment with wastes from energy production industry

International Nuclear Information System (INIS)

Agaev, T.D.; Nadirov, Z.A.; Amiraslanov, K.D.

2004-01-01

Full text : At present thermal power stations give 90 percent of all produced electric power in Azerbaijan. As a result of this the given industry consumes a large amount of organic fuel which have hydrogen and carbon in its content and as a result of this during burning of these components a big amount of harmful gaseous and liquid waste products is formed disposable to an atmosphere and to the ground. That is why gradual environmental contamination happen. Carrying out of measures on prevention of environment pollution is necessary in the fields of functioning these stations. There are also some statistical data on various parameters of described manufacture for various years is given [ru

Economic analysis of waste-to-energy industry in China.

Science.gov (United States)

Zhao, Xin-Gang; Jiang, Gui-Wu; Li, Ang; Wang, Ling

2016-02-01

The generation of municipal solid waste is further increasing in China with urbanization and improvement of living standards. The "12th five-year plan" period (2011-2015) promotes waste-to-energy technologies for the harmless disposal and recycling of municipal solid waste. Waste-to-energy plant plays an important role for reaching China's energy conservation and emission reduction targets. Industrial policies and market prospect of waste-to-energy industry are described. Technology, cost and benefit of waste-to-energy plant are also discussed. Based on an economic analysis of a waste-to-energy project in China (Return on Investment, Net Present Value, Internal Rate of Return, and Sensitivity Analysis) the paper makes the conclusions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Gamma radiation treatment of waste waters from textile industries in ...

African Journals Online (AJOL)

Effects of gamma irradiation alone, and in combination with chemical treatment on color, odor, chemical oxyg-en demand (COD) and suspended solids in waste waters from textile industries in Ghana were studied to explore the potential of alternative and innovative processes for treatment of industrial waste waters. Waste ...

Industrial Hazardous Waste Management In Egypt-the baseline study: An Updated review

International Nuclear Information System (INIS)

Farida M, S.

1999-01-01

Increased industrialization over the past decades in Egypt has resulted in an increased and uncontrolled generation of industrial hazardous waste. This was not accompanied by any concerted efforts to control these wastes. Consequently, no system for handling or disposing of industrial wastes, in general, and industrial hazardous wastes, in specific, exists. In 1993, a baseline report was formulated to assess the overall problem of industrial hazardous waste management in Egypt. Consequently, recommendations for priority actions were identified and the main components of a national hazardous waste system under the provision of Law 4/ 1994 were presented. This paper provides an updated review of this report in light of the proposed technical, legal and institutional guidelines to help in the realization of such a needed waste management system in Egypt

Cleaner production for solid waste management in leather industry ...

African Journals Online (AJOL)

Cleaner production for solid waste management in leather industry. ... From the processes, wastes are generated which include wastewater effluents, solid wastes, and hazardous wastes. In developing countries including Ethiopia, many ... The solid waste inventory of the factory has been carried out. The major problems ...

Sustainable wood waste management in Nigeria

Directory of Open Access Journals (Sweden)

Owoyemi Jacob Mayowa

2016-09-01

Full Text Available Wood industries produce large volumes of residues which must be utilized, marketed or properly disposed of. Heaps of wood residues are common features in wood industries throughout the year. In Nigeria, this residue is generally regarded as waste and this has led to open burning practices, dumping in water bodies or dumping in an open area which constitutes environmental pollution. Sawmills in Nigeria generated over 1,000,000 m3 of wood waste in 2010 while about 5000 m3 of waste was generated in plywood mills. Nigeria generates about 1.8 million tons of sawdust annually and 5.2 million tons of wood wastes. The impact of improper disposal of waste wood on the environment affects both the aquatic and terrestrial ecosystems. Also burning of waste wood releases greenhouse gases into the atmosphere causing various health issues. Reuse/recycling of these wood residues in Nigeria will reduce the pressure on our ever decreasing forests, reduce environmental pollution, create wealth and employment. The literature available on this subject was reviewed and this article, therefore, focuses on the various methods of wood waste disposal and its utilization in Nigerian wood industries, the effects of wood waste on the environment as well as on human health and the benefits of proper wood waste management practices.

Air pollution tolerance indices of some plants around Ama industrial ...

African Journals Online (AJOL)

SAM

2014-03-12

Mar 12, 2014 ... Table 1. Air pollution tolerance index (APTI) of some plant species around some industries in Ama, Enugu State, Nigeria. Plant specie. Site .... these receive most impact from the pollution load in the environment. APTI is an inherent quality of plants to encounter air pollution stress (Rai et al., 2013). These.

The ministry of environment: advanced measures to handle wastes and combat pollution

International Nuclear Information System (INIS)

Chartouni, Talal

1997-01-01

Lebanon is facing environmental problems that stem from wartime chaos, negligence and lack of governmental control. Since the end of the war, environmental protection and getting rid of pollution factors and hazardous waste introduced to Lebanon during the war have become a main concern to the government and the people. The author as an adviser to the environment minister, presents the environment ministry's plan to fight pollution and remove hazardous waste and reveals the steps already executed and the ones to be taken in the future

Cleaner Production Applied in a Small Furniture Industry in Brazil: Addressing Focused Changes in Design to Reduce Waste

Directory of Open Access Journals (Sweden)

Carlos Mario Gutiérrez Aguilar

2017-10-01

Full Text Available The wood industry is known for being among the biggest resource consumers, having a relatively low yield. The wood furniture industry as part of the wood industry also remains a big generator of residues and a big consumer of resources. Diverse solutions and technologies have been developed to deal with the residues generated, but those technologies are mostly applied at the end of the production chain with limited results. Cleaner production represents a program based on continuous strategies applied to a more sustainable use of materials and energy, minimizing waste and pollution. This paper presents a case study of a cleaner production program developed in a small furniture industry in Salvador de Bahia, Brazil, applying the concepts of cleaner production with parameters of ecodesign developed for the furniture industry. The object of study was the production of a wooden chair made from eucalyptus wood. The application of the cleaner production program and ecodesign parameters allowed a detailed characterization of the waste, resulting in opportunities for a reduction of the use of raw material by 30%, a reduction in waste by 49% and allowing a reduction in energy by 36% due to simplification of the productive process. Among the strategies applied were reshaping pieces, redesigning, and the substitution of materials. The results suggest that despite the existence of more complex environmental methods and approaches, the application of cleaner production plus ecodesign parameters could be more achievable for micro and small furniture industries.

Environmental pollution as engine of industrialization

Science.gov (United States)

Antoci, Angelo; Galeotti, Marcello; Sordi, Serena

2018-05-01

This paper analyzes the dynamics of a small open economy with two sectors (a farming sector and an industrial one), heterogeneous agents (workers and entrepreneurs) and free inter-sectoral labor mobility. Labor productivity in the first sector is negatively affected by environmental pollution generated by both sectors, whereas in the second sector it is positively affected by physical capital accumulated by entrepreneurs. Through a global analysis of the non-linear three-dimensional dynamic system of the model we derive conditions under which industrialization generates a decline in workers' revenues in both sectors.

Waste management and pollution at grass-root level in Malaysia: the vision 2020 perspective

International Nuclear Information System (INIS)

Abdul Fatah Yussif; Abdul Rashid Mohamed Shariff

2001-01-01

Malaysia can gain enormously by embracing the global environmental awareness campaign by he United nations Environmental Protection Agency. In order to reap these benefits, a substantial amount of the national budget has to be allocated to oversee waste management and pollution control. However, if certain constrains are not properly addressed, it will lead to waste management and pollution control problem at both urban and municipal levels. The major constrains as identified in a study entitled The implementation constrains in waste management in Malaysia (Law Hieng Ding, 1992), include, lack of proper education of the masses, negligence and discriminate acts, lack of law enforcement by the relevant local authorities and probably discrepancy in the degree of coordination and planning among government agencies. This presentation will address these constraints and suggest a mechanism to better enhance efficient control and management of waste and pollution at grass root level. (Author)

Content of selected elements in Boletus badius fruiting bodies growing in extremely polluted wastes.

Science.gov (United States)

Mleczek, Mirosław; Siwulski, Marek; Mikołajczak, Patrycja; Gąsecka, Monika; Sobieralski, Krzysztof; Szymańczyk, Mateusz; Goliński, Piotr

2015-01-01

The aim of the study was to analyse levels of 17 trace elements and 5 major minerals in 11 Boletus badius fruiting bodies able to grow in extremely polluted waste (flotation tailings) and polluted soil in southern Poland. The presented data widen the limited literature data about the abilities of wild-growing mushroom species to grow on heavily contaminated substrates. Content of elements in waste, soil and mushrooms was analysed by flame atomic absorption spectrometry (FAAS) and cold vapour atomic absorption spectrometry (CVAAS - Hg). The industrial areas differed greatly as regards the content of elements in flotation tailings and soil; therefore differences in Ag, Ba, Cd, Co, Fe, Mo, Ni, Pb, Ca, K, Mg, Na and P accumulation in mushrooms were observed. The highest contents of elements in mushrooms were observed for: As, Al, Cu and Zn (86 ± 28, 549 ± 116, 341 ± 59 and 506 ± 40 mg kg(-1) dry matter, respectively). Calculated bioconcentration factor (BCF) values were higher than 1 for Al (15.1-16.9), Fe (10.6-24.4) and Hg (10.2-16.4) only. The main value of the presented results is the fact that one of the common wild-growing mushroom species was able to grow on flotation tailings containing over 22 g kg(-1) of As and, additionally, effective accumulation of other elements was observed. In view of the high content of the majority of analysed elements in fruiting bodies, edible mushrooms from such polluted areas are nonconsumable.

Radioactive marine pollution

International Nuclear Information System (INIS)

Pontavice, E. du

1976-01-01

Certain provision in international law aim to prevent radioactive marine pollution and others concern compensation of damage from nuclear pollution. Prevention requires regulation of the disposal of wastes from nuclear industry from the operation of nuclear powered ships and from transport of fissile materials. As regards damage, if the measures to limit the extent of the damage come under the law of the sea, the priority of nuclear law over maritime law is clear in respect of financial compensation. (Auth) [fr

Pollution prevention: The role of a university

Energy Technology Data Exchange (ETDEWEB)

Barkenbus, J.N. [Univ. of Tennessee, Knoxville, TN (United States)

1995-12-01

Pollution prevention is at the top of the waste management hierarchy in the United States. If you don`t create pollution in the first place, concerns about transportation, treatment, storage, and disposal of waste are moot. While industry is on the front line in accomplishing significant pollution prevention, universities can play a meaningful role in its accomplishment as well. Universities can do this through three basic missions: education, research, and public service. Examples of how this is carried out at the University of Tennessee, Knoxville are provided. To be fully effective, universities need to organize in an interdisciplinary manner and adopt a public outreach agenda.

A long view of polluting industry and environmental justice in Baltimore

Science.gov (United States)

Christopher G. Boone; Michail Fragkias; Geoffrey L. Buckley; J. Morgan. Grove

2014-01-01

This study examines the density of polluting industry by neighborhoods in Baltimore over the long term, from 1950 to 2010, to determine if high pollution burdens correspond spatially with expected demographic and housing variables predicted in the environmental justice literature. For 1960-1980 we use data on heavy industry from Dun and Bradstreet directories and for...

Environmental problems in Russian coal industry

International Nuclear Information System (INIS)

Kharchenko, V.; Oumnov, V.

1996-01-01

The state of the Russian coal industry is complicated both economically and environmentally. Most mines are unprofitable. Several coal mines are intended to be closed. So, under existing conditions, coal mines are unable to give much attention to environmental protection problems. At the same time, coal mining is one of the most polluting industries. The main trends in this industry's negative influence upon the environment are: land spoilage and immobilization to lay out open-pit mines and mineral waste dump areas and tailing piles as well as with industrial waste water runoff; atmospheric pollution with the air coming from underground and substances blown off from dumps, hydrogeological regime intervention in coal mining areas, etc. One way to solve environmental problems in coal mining is a more rational utilization of the accompanying natural coal resources. Such measures make it possible to obtain complementary profits not only at the expense of reducing environmental destruction but producing new kinds of goods or services as well. Examples of similar solutions are solid mineral wastes utilization, underground space utilization, coal gas utilization and other issues

Environment, pollution and growing health hazards

International Nuclear Information System (INIS)

Mehmud, S.

1987-01-01

The atmosphere surround the planet like a mantle and compositions of atmosphere also changes. The role of high concentration in the stratosphere is vital in as much as it act as a very effective filter for absorbing ultraviolet rays. Different type of wastes that is industrial waste, domestic waste, etc. are being mixed in the environment. The procedure for monitoring pollution in the atmosphere involves the use of a laser radar (LIDAR). Laser beam is sent out in the atmosphere and point of the laser beam back-scattered by the pollutants. Aerosols to the laser radar which receives and processes it with the help of a high speed digital computer. (A.B.)

Zeolites applications in pollution control; radioactive-, municipal-, industrial- and agricultural-waste water treatments: part-I

International Nuclear Information System (INIS)

Akbar, S.

1991-01-01

Zeolite cations exchangers provide a unique combination of selectivity, capacity and stability not available in other ion-exchangers. In this era of environmental concern, the attractive physical and chemical properties of zeolites have been utilized worldwide in the solution to this problem. The desirable characteristics of high ion-exchange selectivity and resistance to radiolytic degradation have made certain zeolites quite useful for the separation and purification of radioisotopes from radioactive wastewater. Zeolites have also been effectively used in nuclear industry for treatment of radioactive wastes and selectively removing ammonium ions from wastewater. (author)

Current Status of Trace Metal Pollution in Soils Affected by Industrial Activities

Science.gov (United States)

Kabir, Ehsanul; Ray, Sharmila; Kim, Ki-Hyun; Yoon, Hye-On; Jeon, Eui-Chan; Kim, Yoon Shin; Cho, Yong-Sung; Yun, Seong-Taek; Brown, Richard J. C.

2012-01-01

There is a growing public concern over the potential accumulation of heavy metals in soil, owing to rapid industrial development. In an effort to describe the status of the pollutions of soil by industrial activities, relevant data sets reported by many studies were surveyed and reviewed. The results of our analysis indicate that soils were polluted most significantly by metals such as lead, zinc, copper, and cadmium. If the dominant species are evaluated by the highest mean concentration observed for different industry types, the results were grouped into Pb, Zn, Ni, Cu, Fe, and As in smelting and metal production industries, Mn and Cd in the textile industry, and Cr in the leather industry. In most cases, metal levels in the studied areas were found to exceed the common regulation guideline levels enforced by many countries. The geoaccumulation index (I geo), calculated to estimate the enrichment of metal concentrations in soil, showed that the level of metal pollution in most surveyed areas is significant, especially for Pb and Cd. It is thus important to keep systematic and continuous monitoring of heavy metals and their derivatives to manage and suppress such pollution. PMID:22645468

Current Status of Trace Metal Pollution in Soils Affected by Industrial Activities

Directory of Open Access Journals (Sweden)

Ehsanul Kabir

2012-01-01

Full Text Available There is a growing public concern over the potential accumulation of heavy metals in soil, owing to rapid industrial development. In an effort to describe the status of the pollutions of soil by industrial activities, relevant data sets reported by many studies were surveyed and reviewed. The results of our analysis indicate that soils were polluted most significantly by metals such as lead, zinc, copper, and cadmium. If the dominant species are evaluated by the highest mean concentration observed for different industry types, the results were grouped into Pb, Zn, Ni, Cu, Fe, and As in smelting and metal production industries, Mn and Cd in the textile industry, and Cr in the leather industry. In most cases, metal levels in the studied areas were found to exceed the common regulation guideline levels enforced by many countries. The geoaccumulation index (Igeo, calculated to estimate the enrichment of metal concentrations in soil, showed that the level of metal pollution in most surveyed areas is significant, especially for Pb and Cd. It is thus important to keep systematic and continuous monitoring of heavy metals and their derivatives to manage and suppress such pollution.

Characterization study of industrial waste glass as starting material ...

African Journals Online (AJOL)

In present study, an industrial waste glass was characterized and the potential to assess as starting material in development of bioactive materials was investigated. A waste glass collected from the two different glass industry was grounded to fine powder. The samples were characterized using X-ray fluorescence (XRF), ...

A review of soil heavy metal pollution from industrial and agricultural regions in China: Pollution and risk assessment.

Science.gov (United States)

Yang, Qianqi; Li, Zhiyuan; Lu, Xiaoning; Duan, Qiannan; Huang, Lei; Bi, Jun

2018-06-14

Soil heavy metal pollution has been becoming serious and widespread in China. To date, there are few studies assessing the nationwide soil heavy metal pollution induced by industrial and agricultural activities in China. This review obtained heavy metal concentrations in soils of 402 industrial sites and 1041 agricultural sites in China throughout the document retrieval. Based on the database, this review assessed soil heavy metal concentration and estimated the ecological and health risks on a national scale. The results revealed that heavy metal pollution and associated risks posed by cadmium (Cd), lead (Pb) and arsenic (As) are more serious. Besides, heavy metal pollution and associated risks in industrial regions are severer than those in agricultural regions, meanwhile, those in southeast China are severer than those in northwest China. It is worth noting that children are more likely to be affected by heavy metal pollution than adults. Based on the assessment results, Cd, Pb and As are determined as the priority control heavy metals; mining areas are the priority control areas compared to other areas in industrial regions; food crop plantations are the priority control areas in agricultural regions; and children are determined as the priority protection population group. This paper provides a comprehensive ecological and health risk assessment on the heavy metals in soils in Chinese industrial and agricultural regions and thus provides insights for the policymakers regarding exposure reduction and management. Copyright © 2018. Published by Elsevier B.V.

Characterization of tannery sludge from the leather industry of Franca industrial district, SP, Brazil

International Nuclear Information System (INIS)

Chambi, M.M.; Toffoli, S.M.

2011-01-01

The industry of leather manufacture generates large quantities of solid leather waste with characteristics of high-polluting and hazardous conditions. Among these wastes, stands out the wet blue leather (chromed leather scraps), and the tanning sludge and secondary sludge generated in the processes of effluents treatment. These wastes contain Cr(III), which, under oxidizing conditions, can turn into Cr (VI), which is highly toxic. However, these wastes are a potential source of chromium oxide (traditional industrial pigment), which could be used by the glass and ceramic enamel industries. In this study, a preliminary characterization of a chromium sludge from the industrial district of Franca-SP was conducted. X-ray diffraction (XRD), chemical (XRF) and thermal (DTA / TG) analyses were used to determine the physical and chemical characteristics of this solid waste. The potential of using this material as an available and cheap pigment for the manufacture of enamels and glass is discussed. (author)

Hazardous waste management in research laboratories

International Nuclear Information System (INIS)

Sundstrom, G.

1989-01-01

Hazardous waste management in research laboratories benefits from a fundamentally different approach to the hazardous waste determination from industry's. This paper introduces new, statue-based criteria for identifying hazardous wastes (such as radiological mixed wastes and waste oils) and links them to a forward-looking compliance of laboratories, the overall system integrates hazardous waste management activities with other environmental and hazard communication initiatives. It is generalizable to other waste generators, including industry. Although only the waste identification and classification aspects of the system are outlined in detail here, four other components are defined or supported, namely: routine and contingency practices; waste treatment/disposal option definition and selection; waste minimization, recycling, reuse, and substitution opportunities; and key interfaces with other systems, including pollution prevention

The impact of industrial pollution on macrobenthic fauna communities

African Journals Online (AJOL)

Mossa creek is a long, deep, tidal canal in Iran. The creek stretches almost 56 km along the northwestern edge of the Persian Gulf. The creek contains numerous sources of organic pollution including industrial sewage effluent. A survey of the creek was performed assessing organic pollution, water properties, and the ...

Effect of industrial pollution on behaviour of radionuclides in forest ecosystems; Forests ecosystems

Energy Technology Data Exchange (ETDEWEB)

Outola, I. (STUK-Radiation and Nuclear Safety Authority, Helsinki (Finland))

2009-06-15

To investigate how and to what extent industrial pollution affects the behaviour of radionuclides in forest ecosystems, studies were conducted in the vicinity of two Cu-Ni smelters: one in a pine forest at Harjavalta, Finland, and the other in a spruce forest at Monchegorsk, Russia. Industrial pollution had significant effects on the distribution of radionuclides in soil horizons. With the increase in pollution towards the smelter, radionuclides were accumulated more in the litter layer because the conversion of litter into organic material was diminished due to inhibited microbial activity. As a result, the organic layer contained less radionuclides towards the smelter. The effect of industrial pollution on soil-to-plant transfer was complex. The effect varied with radionuclide, plant species and also on forest type. For 137Cs, soil-to-plant transfer decreased significantly as industrial pollution increased in pine forest, whereas the decrease was less pronounced in spruce forest. Root uptake of 239,240Pu by plants is extremely small, and plant contamination by resuspended soil is an important factor in considering the soil-to-plant transfer of this radionuclide. In spruce forest, more plutonium was transferred into plants when pollution load increased due to resuspension of litter particles, which contained higher concentrations of plutonium in the vicinity of the smelter. Soil-to-plant transfer of plutonium was much less affected in pine forests contaminated with industrial pollution. This research clearly indicates the sensitivity of the northern forest ecosystem to inorganic pollutants. Prediction of the soil-to-plant transfer of radionuclides in industrially polluted forest ecosystems requires detailed information on the total deposition, vertical distribution of radionuclides in soil, soil microbiological factors, other soil parameters as well as the rooting depths of the plants. (LN)

Environmental Restoration Contractor Waste Minimization and Pollution Prevention Plan

International Nuclear Information System (INIS)

Duvon, D. K.

1998-01-01

This plan contains the Pollution Prevention (P2) Program for the Environmental Restoration Contractor (ERC). The plan outlines the activities and schedules developed by the Bechtel Hanford, Inc.(BHI) to reduce the quantity and toxicity of waste dispositioned as a result of restoration and remediation activities. The purpose of this plan is to guide ERC projects in meeting and documenting compliance with requirements for pollution prevention. This plan contains the objectives, strategy, and support activities of the ERC P2 Program

Waste water treatment plant city of Kraljevo

Directory of Open Access Journals (Sweden)

Marinović Dragan D.

2016-01-01

Full Text Available In all countries, in the fight for the preservation of environmental protection, water pollution, waste water is one of the very serious and complex environmental problems. Waste waters pollute rivers, lakes, sea and ground water and promote the development of micro-organisms that consume oxygen, which leads to the death of fish and the occurrence of pathogenic microbes. Water pollution and determination of its numerous microbiological contamination, physical agents and various chemical substances, is becoming an increasing health and general social problem. Purification of industrial and municipal waste water before discharge into waterways is of great importance for the contamination of the water ecosystems and the protection of human health. To present the results of purification of industrial and municipal wastewater in the city center Kraljevo system for wastewater treatment. The investigated physical and chemical parameters were performed before and after the city's system for wastewater treatment. The results indicate that the effect of purification present the physical and chemical parameters in waste water ranges from 0 - 19%.

Principles of development of the industry of technogenic waste processing

Directory of Open Access Journals (Sweden)

Maria A. Bayeva

2014-01-01

Full Text Available Objective to identify and substantiate the principles of development of the industry of technogenic waste processing. Methods systemic analysis and synthesis method of analogy. Results basing on the analysis of the Russian and foreign experience in the field of waste management and environmental protection the basic principles of development activities on technogenic waste processing are formulated the principle of legal regulation the principle of efficiency technologies the principle of ecological safety the principle of economic support. The importance of each principle is substantiated by the description of the situation in this area identifying the main problems and ways of their solution. Scientific novelty the fundamental principles of development of the industry of the industrial wastes processing are revealed the measures of state support are proposed. Practical value the presented theoretical conclusions and proposals are aimed primarily on theoretical and methodological substantiation and practical solutions to modern problems in the sphere of development of the industry of technogenic waste processing.

Treatment of wastewater from rubber industry in Malaysia ...

African Journals Online (AJOL)

Treatment of wastewater from rubber industry in Malaysia. ... Discharge of untreated rubber effluent to waterways resulted in water pollution that affected the human health. ... Key words: Rubber industry, effluent, waste management, Malaysia.

Annual report of waste generation and pollution prevention progress 1997

International Nuclear Information System (INIS)

1998-09-01

This sixth Annual Report presents and analyzes DOE Complex-wide waste generation and pollution prevention activities at 36 reporting sites from 1993 through 1997. In May 1996, the Secretary of Energy established a 50 percent Complex-Wide Waste Reduction Goal (relative to the 1993 baseline) for routine operations radioactive and hazardous waste generation, to be achieved by December 31, 1999. Excluding sanitary waste, routine operations waste generation increased three percent from 1996 to 1997, and decreased 61 percent overall from 1993 to 1997. DOE has achieved its Complex-Wide Waste Reduction Goals for routine operations based upon a comparison of 1997 waste generation to the 1993 baseline. However, it is important to note that increases in low-level radioactive and low-level mixed waste generation could reverse this achievement. From 1996 to 1997, low-level radioactive waste generation increased 10 percent, and low-level mixed waste generation increased slightly. It is critical that DOE sites continue to reduce routine operations waste generation for all waste types, to ensure that DOE's Complex-Wide Waste Reduction Goals are achieved by December 31, 1999

Seiler Pollution Control Systems vitrification process for the treatment of hazardous waste streams

International Nuclear Information System (INIS)

Nuesch, P.C.; Sarko, A.B.

1995-01-01

Seiler Pollution Control Systems, Inc. (Seiler) applies an economical, transportable, compact high temperature vitrification process to recycle and/or stabilize mixed organic/inorganic waste streams. Organic components are gasified by the system and are used as an auxiliary energy source. The inorganic components are melted and bound up molecularly in a glass/ceramic matrix. These glass/ceramics are extremely stable and durable and will pass typical regulatory leachate tests. Waste types that can be processed through the Seiler vitrification system include incinerator flyash, paint sludges, plating wastes, metal hydroxide sludges, low level and mixed radioactive wastes, contaminated soils and sludges, asbestos, and various mixed organic/inorganic residues. For nonradioactive waste streams, a variety of commercially saleable glass/ceramic products can be produced. These materials are marketed either as architectural materials, abrasives, or insulating refractories. The glass/ceramics generated from radioactive waste streams can be formed in a shape that is easily handled, stored, and retrieved. The system, itself is modular and can either be used as a stand alone system or hooked-up in line to existing manufacturing and production facilities. It consists of four sections: feed preparation; preheater; vitrifier/converter, and air pollution control. The vitrification system can use oxygen enriched natural gas or fuel oil for both cost efficiency and to reduce air pollution emissions

Gaseous emissions from industrial processes: Municipal solid waste incinerators

Energy Technology Data Exchange (ETDEWEB)

Cassitto, L.; Gallarini, V.; Magnani, P.; Rizzi, A. (Politecnico di Milano, Milan (Italy). Impianti Condizionamento e Fisica Tecnica Artea, Milan (Italy))

A survey of European Communities proposed air pollution standards is coupled with an examination of the technical feasibility of building and operating municipal solid waste incineration plants that can successfully meet those standards. The results of the analysis indicate that modern incineration plants equipped with cogeneration and current-technology materials and energy recovery systems offer a significant contribution to meeting Italian national energy requirements and contemporaneously provide a decisive answer to the pressing need for safe and effective urban area waste disposal. The paper cautions however any final decision making must be based on extensive cost benefit analyses to determine the optimum combination of incinerator plant energy production and pollution control systems.

Air pollutant emissions and their control with the focus on waste incineration facilities

Energy Technology Data Exchange (ETDEWEB)

Loeschau, Margit [Wandschneider + Gutjahr, Hamburg (Germany)

2017-07-01

This text and practical handbook thoroughly presents the control of air pollutant emissions from combustion processes focusing on waste incinerators. Special characteristics are emphasised and the differences to emission control from combustion processes with other fuels are explained. The author illustrates the origin and effects of air pollutants from incineration processes, the mechanics of their appearance in the incineration process, primary and secondary measures for their reduction, processes of measuring the emissions as well as the methods of disposing the residues. In particular, the pros and cons of procedural steps and their appropriate combination under various conditions are emphasised. Moreover, the book contains information and analyses of the emissions situation, the consumption of operating materials and of backlog quantities as well as of the cost structure of waste incinerators with regard to their applied control system. Furthermore, the author explicates the contemporary legal, scientific and technological developments and their influence on air pollutant emission control. An evaluation of the status quo of air pollutant control at waste incinerators in Germany, practical examples about possible combinations and typical performance data complete the content. Accordingly, this book is a guideline for planing a reasonable overall concept of an air pollutant control that takes the location and the segregation tasks into consideration.

An industrial ecology approach to municipal solid waste management: I. Methodology

Science.gov (United States)

Municipal solid waste (MSW) can be viewed as a feedstock for industrial ecology inspired conversions of wastes to valuable products and energy. The industrial ecology principle of symbiotic processes using waste streams for creating value-added products is applied to MSW, with e...

[Study on strategies of pollution prevention in coastal city of Zhejiang Province based on scenario analysis].

Science.gov (United States)

Tian, Jin-Ping; Chen, Lü-Jun; Du, Peng-Fei; Qian, Yi

2013-01-01

Scenario analysis was used to study the environmental burden in a coastal city of Zhejiang province under different patterns of economic development. The aim of this research is to propose advices on decision making by illustrating how to make emissions reduced by transforming the pattern of economic development in a developed coastal area, which had acquired the level of 70 000 yuan GDP per cap. At first, 18 heavy pollution industries were screened out, by referencing total emissions of chemical oxygen demand, ammonia-nitrogen, sulfur dioxide, and nitrogen oxide. Then, a model of scenario analysis and the back-up calculation program were designed to study the sustainable development of the heavy pollution industries. With 2008 and 2015 as the reference year and the target year respectively, emissions of four pollutants mentioned above in the 18 heavy pollution industries in the city were analyzed under six scenarios. The total emissions of 4 pollutants should be reduced to an expectant degree, which is set as the constraint prerequisite of the scenario analysis. At last, some suggestions for decision-making are put forward, which include maintaining a moderate increase rate of GDP around 7%, strengthening the adjustment of economic structure, controlling the increasing rate of industrial added value of the industries with heavy pollution, optimizing the structure of industries with heavy pollution, decreasing the intensity of waste emission by implementing cleaner production to reduce emission produce at the source, and strengthening regulations on the operation of waste treatment plants to further promote the efficiency of waste treatment. Only by implementing such measures mentioned above, can the total emissions of chemical oxygen demand, ammonia-nitrogen, sulfur dioxide, and nitrogen oxide of the 18 industries with heavy pollution in the city be reduced by a 10%, 10%, 5%, and 15% respectively based on the reference year.

The U.S. DOE new production reactor/heavy water reactor facility pollution prevention/waste minimization program

International Nuclear Information System (INIS)

Kaczmarsky, Myron M.; Tsang, Irving; Stepien, Walter P.

1992-01-01

A Pollution Prevention/Waste Minimization Program was established during the early design phase of the U.S. DOE's New Production Reactor/Heavy Water Reactor Facility (NPR/HWRF) to encompass design, construction, operation and decommissioning. The primary emphasis of the program was given to waste elimination, source reduction and/or recycling to minimize the quantity and toxicity of material before it enters the waste stream for treatment or disposal. The paper discusses the regulatory and programmatic background as it applies to the NPR/HWRF and the waste assessment program developed as a phased approach to pollution prevention/waste minimization for the NPR/HWRF. Implementation of the program will be based on various factors including life cycle cost analysis, which will include costs associated with personnel, record keeping, transportation, pollution control equipment, treatment, storage, disposal, liability, compliance and oversight. (author)

Activation of bentonite to remove the chromium from waste water produced by panning industry, and studying the chromium recovery efficiency

International Nuclear Information System (INIS)

Abbasi, S.; Wahba, H.; AL-Masri, M.S.

2010-01-01

The fast development of tanning industry led to an increase in environmental problems resulting from discharging its wastes to the surrounding environment. Thus solving this problem became one of the most important aims that the researchers work on. The chromium content of the industrial water wastes of the tanning industry considered as the main pollutant for the environment. The Aleppo Bentonite is used in early research to remove the chromium from the industrial waste water.The current research aims to find a method to activate the Aleppo Bentonite in order to increase the effective removal of chromium from the industrial waste water which is produced by tanning industry, as well as to specify the optimal conditions for chromium recovery.This study used the Aleppo Bentonite, whose origin is Tal Ajar-Aleppo to study the activation aspects using Sulfuric Acid, Hydrochloric Acid and Nitric Acid, in addition to study the recovery aspects using the same acids and hydrogen peroxide and to specify the optimal conditions for chromium recovery through applying some experiments based on three main factors: concentration, settling time and temperature.It was observed from the applied experiments that it is possible to recover chromium from Bentonite efficiently up to (80% - 90%) by treating the Bentonite with hydrogen peroxide(33% concentration) at room temperature, or by treating it with hydrogen peroxide(8.25% concentration) at 75 o C, while the settling time factor proved that full recovery of chromium is obtained during the first hour, and increasing the time factor does not affect the efficiency of chromium recovery. (author)

Panel discussion on 'Government and industry social responsibility towards potential communities hosting radioactive waste management sites'

International Nuclear Information System (INIS)

Cragg, W.; Storey, K.; Cooper, H.; McIntyre, J.; Brown, P.

2006-01-01

'Full text:' In healthy democracies, support from local communities for industrial/development projects is highly desirable. What are the respective roles of the various stakeholder sectors, i.e. governments, industry, and communities around industrial projects, including waste management facilities, and how can they interact with sustainable development in mind? Should the private sector be involved in public policy? Should the public sector have an active role in providing funding complementing the notion of the Polluter pays principle? Should communities have a greater role in overseeing the activities of industry and be enabled to do so? Should communities be empowered to increase their role in decision-making processes? Are there trends emerging in this area? Are there improvements to be made? The Not-in-My-Backyard (NIMBY) reflex is not e thical . Thoughtful review is required when considering the right or the desirability to develop. Each of the invited panel members will briefly approach this issue from the perspective of their respective sector. A discussion period will ensue which hopefully will provide insight into how diverse sectors can work together to ensure the establishment of radioactive waste management facilities in communities which support such projects based on local and national values. (author)

Evaluation of toxicity level of the polluted eco-system for an industrial city of Pakistan

International Nuclear Information System (INIS)

Husaini, S.N.; Matiullah; Akram, M.; Arif, M.

2011-01-01

The indiscriminate discharge of untreated industrial effluents and solid wastes into the open environment poses a serious threat to the ecosystem. Gujranwala is an industrial city of Pakistan wherein a large number of different industries are situated and majority of them are not equipped with proper recycling or effluent treatment plants. Unfortunately, untreated industrial effluents are locally used for the irrigation purposes which may result in higher concentrations of toxic metals in the crops and vegetables. Therefore, prime objective of the present study was to determine concentrations of toxic metals in the polluted soils, vegetables and crops grown in the vicinity of industrial areas using neutron activation analysis technique. The results obtained showed higher values of toxic metals in the studied samples. The observed highest concentration of As (0.94 ± 0.06) in spinach, Br (69 ± 9) in turnip, Co (0.83 ± 0.01) in millet, Cr (51.7 ± 4.2) in wheat, Mn (76.2 ± 7.3) in tomato, Sb (0.5 ± 0.06) in rice, Cl (31698 ± 3921) and Se (3.4 ± 0.4) in carrot. These values are higher than those reported in the literature. (author)

Characterization of low-level waste from the industrial sector, and near-term projection of waste volumes and types

International Nuclear Information System (INIS)

MacKenzie, D.R.

1988-01-01

A telephone survey of low-level waste generators has been carried out in order to make useful estimates of the volume and nature of the waste which the generators will be shipping for disposal when the compacts and states begin operating new disposal facilities. Emphasis of the survey was on the industrial sector, since there has been little information available on characteristics of industrial LLW. Ten large industrial generators shipping to Richland, ten shipping to Barnwell, and two whose wastes had previously been characterized by BNL were contacted. The waste volume shipped by these generators accounted for about two-thirds to three-quarters of the total industrial volume. Results are given in terms of the categories of LLW represented and of the chemical characteristics of the different wastes. Estimates by the respondents of their near-term waste volume projections are presented

Characterization of low-level waste from the industrial sector, and near-term projection of waste volumes and types

International Nuclear Information System (INIS)

MacKenzie, D.R.

1988-01-01

A telephone survey of low-level waste generators has been carried out in order to make useful estimates of the volume and nature of the waste which the generators are shipping for disposal when the compacts and states begin operating new disposal facilities. Emphasis of the survey was on the industrial sector, since there has been little information available on characteristics of industrial LLW. Ten large industrial generators shipping to Richland, ten shipping to Barnwell, and two whose wastes had previously been characterized by BNL were contacted. The waste volume shipped by these generators accounted for about two-thirds to three-quarters of the total industrial volume. Results are given in terms of the categories of LLW represented and of the chemical characteristics of the different wastes. Estimates by the respondents of their near-term waste volume projections are presented

Noise pollution in iron and steel industry

International Nuclear Information System (INIS)

Bisio, G.; Piromalli, W.; Acerbo, P.

1999-01-01

Iron and steel industry is characterized by high energy consumption and thus present remarkable problems from the point of view of noise pollution. The aims of this paper is to examine characteristic and acoustical emissions and immisions of some fundamentals iron and steel plants with several remarks on the possible measures to reduce noise pollution. For a large integrate iron and steel system, some surveys are shown with all devices running and, in addition, comparisons are made with other surveys when the main devices were out of service owing to great maintenance works [it

[Relationships between economic growth and industrial pollutant discharge of Suzhou: how about the EKC?].

Science.gov (United States)

Ling, Hong; Zhu, Xiao-Dong; Wang, Hui-Zhong; Yin, Rong-Yao; Wang, Xiang-Hua; Zhao, Wen-Jun

2009-04-01

Based on the study of the relationships between economic growth and industrial pollutant discharge of Suzhou City in 1991-2005, the environmental Kuznets curve (EKC) of the City was estimated by several kinds of function, with the cause analyzed. The results showed that the EKC of Suzhou was not a typical one. The industrial pollution of the City increased dramatically by scale effect of economic growth and the clear environmental benefit of industrial structure adjustment was not received obviously, while generalized discharge reduction technologies showed great results. In general terms, the pollution increase was comparatively slower than the GDP growth. As a whole, the environmental policy of Suzhou was in effect. However, the relationships between economic growth and industrial pollutant discharge had not been a benign development yet. In order to achieve win-win situation of economic growth and pollution reduction, Suzhou needed to optimize its industry structure, push the energy conservation and discharge reduction policy deeply, increase environmental investment, and enforce the strictest environmental and industrial policy. In doing these, Suzhou could turn the traditional omega-shaped EKC into delta-shaped EKC.

Industrial waste treatment: the leather industry; Tratamiento conjunto de aguas residuales e industriales: caso de las industrias del curtido

Energy Technology Data Exchange (ETDEWEB)

Cortacans Torre, J.A.

1995-07-01

The industrial waste water treatment can be presented alone or together with the urban waste water. There are special industries that cannot treat their effluents together with municipal effluents, for example the leather industry. This industry uses sulfurs and equivalent chromium. The PH value is around 10. This waste water can`t be introduce directly into municipal collectors. This article presents the general recommendations for their treatment.

Solid waste management - Pakistan's perspective

International Nuclear Information System (INIS)

Hussain, M.

2003-01-01

The discipline of 'Solid Waste Management' is as old as human civilization itself. The problem had been felt when the human beings commenced living together in the form of communities. The situation got worsened with ever-increasing population and growing industrialization. The developed nations have endeavored to tackle the issue of the industrial and municipal wastes according to the principles of engineering and environment. Most of the developing countries have not dealt with the 'Third Pollution' in the eco-friendly manner. Ironically Pakistan is facing this serious menace because of ever-expanding population (2.2% per annum) and ill management of the wastes and effluents being generated from multifarious activities. These pollutants are degrading the land, air and water resources at alarming rates. In Pakistan about 7,250 tonnes of solid waste is generated per day. Of this quantity only 60-70% is collected and the remaining quantity is allowed to burn indiscriminately or decay in situ. Unfortunately the industrial waste, animal dung and hospital waste are allowed to mix with the municipal waste, which adds to inefficiency of the existing 'Solid Waste Management System'. Scores of faecal, fly, rodent and mosquito born diseases are caused due to open dumping of the waste besides aesthetic impairment of the surroundings. None of the scientifically recognized methods of disposal is practiced. It is not based on administrative, financial, environmental and technical consideration. There is dire necessity of educating the masses to adopt clean habits and resort to generation of minimum waste. Further, nothing is waste as the so-called 'waste material' is the raw material after reuse and recycling for another process. (author)

Bioremediation of industrial waste through mushroom cultivation.

Science.gov (United States)

Kulshreshtha, Shweta; Mathur, Nupur; Bhatnagar, Pradeep; Jain, B L

2010-07-01

Handmade paper and cardboard industries are involved in processing of cellulosic and ligno-cellulosic substances for making paper by hand or simple machinery. In the present study solid sludge and effluent of both cardboard and handmade paper industries was collected for developing a mushroom cultivation technique to achieve zero waste discharges. Findings of present research work reveals that when 50% paper industries waste is used by mixing with 50% (w/w) wheat straw, significant increase (96.38%) in biological efficiency over control of wheat straw was observed. Further, cultivated basidiocarps showed normal morphology of stipe and pileus. Cross section of lamellae did not show any abnormality in the attachment of basidiospores, hymenal trama and basidium. No toxicity was found when fruiting bodies were tested chemically.

Geodiametris: an integrated geoinformatic approach for monitoring land pollution from the disposal of olive oil mill wastes

Science.gov (United States)

Alexakis, Dimitrios D.; Sarris, Apostolos; Papadopoulos, Nikos; Soupios, Pantelis; Doula, Maria; Cavvadias, Victor

2014-08-01

The olive-oil industry is one of the most important sectors of agricultural production in Greece, which is the third in olive-oil production country worldwide. Olive oil mill wastes (OOMW) constitute a major factor in pollution in olivegrowing regions and an important problem to be solved for the agricultural industry. The olive-oil mill wastes are normally deposited at tanks, or directly in the soil or even on adjacent torrents, rivers and lakes posing a high risk to the environmental pollution and the community health. GEODIAMETRIS project aspires to develop integrated geoinformatic methodologies for performing monitoring of land pollution from the disposal of OOMW in the island of Crete -Greece. These methodologies integrate GPS surveys, satellite remote sensing and risk assessment analysis in GIS environment, application of in situ and laboratory geophysical methodologies as well as soil and water physicochemical analysis. Concerning project's preliminary results, all the operating OOMW areas located in Crete have been already registered through extensive GPS field campaigns. Their spatial and attribute information has been stored in an integrated GIS database and an overall OOMW spectral signature database has been constructed through the analysis of multi-temporal Landsat-8 OLI satellite images. In addition, a specific OOMW area located in Alikianos village (Chania-Crete) has been selected as one of the main case study areas. Various geophysical methodologies, such as Electrical Resistivity Tomography, Induced Polarization, multifrequency electromagnetic, Self Potential measurements and Ground Penetrating Radar have been already implemented. Soil as well as liquid samples have been collected for performing physico-chemical analysis. The preliminary results have already contributed to the gradual development of an integrated environmental monitoring tool for studying and understanding environmental degradation from the disposal of OOMW.

Strategy of Construction and Demolition Waste Management after Chemical Industry Facilities Removal

Science.gov (United States)

Tashkinova, I. N.; Batrakova, G. M.; Vaisman, Ya I.

2017-06-01

Mixed waste products are generated in the process of irrelevant industrial projects’ removal if conventional techniques of their demolition and dismantling are applied. In Russia the number of unused chemical industry facilities including structures with high rate of wear is growing. In removing industrial buildings and production shops it is used conventional techniques of demolition and dismantling in the process of which mixed waste products are generated. The presence of hazardous chemicals in these wastes makes difficulties for their use and leads to the increasing volume of unutilized residues. In the process of chemical industry facilities’ removal this fact takes on special significance as a high level of hazardous chemicals in the waste composition demands for the realization of unprofitable measures aimed at ensuring environmental and industrial safety. The proposed strategy of managing waste originated from the demolition and dismantling of chemical industry facilities is based on the methodology of industrial metabolism which allows identifying separate material flows of recycled, harmful and ballast components, performing separate collection of components during removal and taking necessary preventive measures. This strategy has been tested on the aniline synthesis plant being in the process of removal. As a result, a flow of 10 wt. %, subjected to decontamination, was isolated from the total volume of construction and demolition waste (C&D waste). The considered approach allowed using the resource potential of more than 80wt. % of waste and minimizing the disposed waste volume.

Production of Enzymes From Agricultural Wastes and Their Potential Industrial Applications.

Science.gov (United States)

Bharathiraja, S; Suriya, J; Krishnan, M; Manivasagan, P; Kim, S-K

Enzymatic hydrolysis is the significant technique for the conversion of agricultural wastes into valuable products. Agroindustrial wastes such as rice bran, wheat bran, wheat straw, sugarcane bagasse, and corncob are cheapest and plentifully available natural carbon sources for the production of industrially important enzymes. Innumerable enzymes that have numerous applications in industrial processes for food, drug, textile, and dye use have been produced from different types of microorganisms from agricultural wastes. Utilization of agricultural wastes offers great potential for reducing the production cost and increasing the use of enzymes for industrial purposes. This chapter focuses on economic production of actinobacterial enzymes from agricultural wastes to make a better alternative for utilization of biomass generated in million tons as waste annually. © 2017 Elsevier Inc. All rights reserved.

Comprehensive waste characterization and organic pollution co-occurrence in a Hg and As mining and metallurgy brownfield.

Science.gov (United States)

Gallego, J R; Esquinas, N; Rodríguez-Valdés, E; Menéndez-Aguado, J M; Sierra, C

2015-12-30

The abandonment of Hg-As mining and metallurgy sites, together with long-term weathering, can dramatically degrade the environment. In this work it is exemplified the complex legacy of contamination that afflicts Hg-As brownfields through the detailed study of a paradigmatic site. Firstly, an in-depth study of the former industrial process was performed to identify sources of different types of waste. Subsequently, the composition and reactivity of As- and Hg-rich wastes (calcines, As-rich soot, stupp, and flue dust) was analyzed by means of multielemental analysis, mineralogical characterization (X-ray diffraction, electronic, and optical microscopy, microbrobe), chemical speciation, and sequential extractions. As-rich soot in the form of arsenolite, a relatively mobile by-product of the pyrometallurgical process, and stupp, a residue originated in the former condensing system, were determined to be the main risk at the site. In addition, the screening of organic pollution was also aimed, as shown by the outcome of benzo(a) pyrene and other PAHs, and by the identification of unexpected Hg organo-compounds (phenylmercury propionate). The approach followed unravels evidence from waste from the mining and metallurgy industry that may be present in other similar sites, and identifies unexpected contaminants overlooked by conventional analyses. Copyright © 2015 Elsevier B.V. All rights reserved.

Revealing the costs of air pollution from industrial facilities in Europe

Energy Technology Data Exchange (ETDEWEB)

Holland, M. (EMRC, Brussels (Belgium)); Wagner, A.; Davies, T. (AEA Technology, Harwell (United Kingdom)); Spadaro, J. (SERC, Charlotte, NC (United States)); Adams, M. (EEA, Copenhagen (Denmark))

2011-11-15

This European Environment Agency (EEA) report assesses the damage costs to health and the environment resulting from pollutants emitted from industrial facilities. It is based on the latest information, namely for 2009, publicly available through the European Pollutant Release and Transfer Register (E-PRTR, 2011) in line with the United Nations Economic Commission for Europe (UNECE) Aarhus Convention regarding access to environmental information. This report investigates the use of a simplified modelling approach to quantify, in monetary terms, the damage costs caused by emissions of air pollutants from industrial facilities reported to the E-PRTR pollutant register. The approach is based on existing policy tools and methods, such as those developed under the EU's CAFE programme for the main air pollutants. This study also employs other existing models and approaches used to inform policymakers about the damage costs of pollutants. Together, the methods are used to estimate the impacts and associated economic damage caused by a number of pollutants emitted from industrial facilities, including: (1) ammonia (NH{sub 3}), nitrogen oxides (NO{sub x}), non-methane volatile organic compounds (NMVOCs), particulate matter (PM{sub 10}) and sulphur oxides (SO{sub x}); (2) heavy metals; (3) benzene, dioxins and furans, and polycyclic aromatic hydrocarbons (PAHs); (4) carbon dioxide (CO{sub 2}). The cost of damage caused by emissions from the E-PRTR industrial facilities in 2009 is estimated as being at least EUR 102-169 billion. A small number of industrial facilities cause the majority of the damage costs to health and the environment. Fifty per cent of the total damage cost occurs as a result of emissions from just 191 (or 2 %) of the approximately 10 000 facilities that reported at least some data for releases to air in 2009. Three quarters of the total damage costs are caused by the emissions of 622 facilities, which comprise 6 % of the total number. Of the

Community Solutions to Solid Waste Pollution. Operation Waste Watch: The New Three Rs for Elementary School. Grade 6. [Second Edition.

Science.gov (United States)

Virginia State Dept. of Waste Management, Richmond. Div. of Litter & Recycling.

This publication, the last in a series of seven for elementary schools, is an environmental education curriculum guide with a focus on waste management issues. It contains a unit of exercises selected for sixth grade students focusing on community solutions to solid waste pollution. Waste management activities included in this unit seek to…

Cleaner production: Minimizing hazardous waste in Indonesia

Energy Technology Data Exchange (ETDEWEB)

Bratasida, D.L. [BAPEDAL, Jakarta (Indonesia)

1996-12-31

In the second long-term development plan, industry plays a significant role in economic growth. In Indonesia, industries grow very fast; such fast growth can adversely effect the environment. Exploitation of assets can mean depletion of natural resources and energy, which, if incorrectly managed, can endanger human life and the environment. The inefficient use of natural resources will accelerate their exhaustion and generate pollution, resulting in environmental damage and threats to economic development and human well being. In recent years, changes in the approach used to control pollution have been necessary because of the increasing seriousness of the problems. Initial environmental management strategies were based on a carrying capacity approach; the natural assimilative capacity accommodated the pollution load that was applied. The environmental management strategies adopted later included technologies applied to the end of the discharge point (so-called {open_quotes}end-of-pipe{close_quotes} treatments). Until now, environmental management strategies focused on end-of-pipe approaches that control pollutants after they are generated. These approaches concentrate on waste treatment and disposal to control pollution and environmental degradation. However, as industry develops, waste volumes continue to increase, thereby creating further environmental problems. In addition, the wastes produced tend to have more complex characteristics and are potentially more difficult to treat for a reasonable cost. There are often technical and financial obstacles to regulatory compliance if waste treatment is relied on as the only means of achieving environmental objectives. Consequently, the reactive end-of-pipe treatment approach has been changed to a proactive cleaner production approach. This approach is based on the concept of sustainable development and is designed to prevent pollution as well as to protect natural resources and the quality of the environment.

Waste management practices in Ontario`s workplaces: An emerging industrial ecology

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

Describes a study commissioned to evaluate employee attitudes and behaviours with respect to participation in workplace initiatives in waste diversion/reduction, to examine management initiatives related to waste diversion and reduction/recycling/reuse, and to report on Ontario Ministry of Environment & Energy activities related to industrial, commercial, and institutional (ICI) waste diversion activities. Linkages between management and employees, management and government, and ICI activities and government were also studied. The study methodology included a literature review, a series of interviews with key stakeholders, industry associations, and waste management companies, and a series of 12 case studies spanning major industrial sectors in Ontario. Issues addressed in the study include the factors that trigger waste diversion activities by ICI establishments, barriers to the initiation of waste diversion practices, and the social aspects of waste reduction/recycling/reuse practices.

COLOR POLLUTION CONTROL IN TEXTILE DYEING INDUSTRY ...

African Journals Online (AJOL)

a

tannery sludge derived activated carbon is lower compared with commercial ... industrial solid waste for the treatment of wastewater is a win-win strategy ..... The authors are thankful to the management of VIT University, Vellore, India for ...

Air pollution from biodegradable wastes and non-specific health symptoms among residents

DEFF Research Database (Denmark)

Blanes-Vidal, Victoria

2015-01-01

Adverse health effects of exposure to high levels of air pollutants from biodegradable wastes have been well-studied. However, few investigations have examined the potential effects of chronic exposure to low-to-moderate levels on non-specific health symptoms among residents. Besides, most studies...... have relied on distances to waste sites to assign exposure status, and have not investigated whether the exposure-symptoms associations are direct or mediated by odor annoyance. In this study, individual-level exposures to a proxy indicator of biodegradable waste pollution (ammonia, NH3) in non......-urban residences (n=454) during 2005-2010 were characterized by data from emission-dispersion validated models. Logistic regression and mediating analyses were used to examine associations between exposures and questionnaire-based data on annoyance and non-specific symptoms, after adjusting by person...

The Effect of Chitosan Dosage Againts Liquid Waste Water Color on "Oriens Handicraft" Sasirangan Home Industry, Landasan Ulin

Directory of Open Access Journals (Sweden)

Arifin Arifin

2017-08-01

Full Text Available The growth of sasirangan fabricated prodution has brought positive impact on the welfare of Banjarnese people.  On the other hand, it also have negative impacts in the form environmental pollution as a result of sasirangan industrial liquid waste disposal without any proper treatment proccess. This study aims to determine the effect of chitosan dosage againts liquid waste water color on "Oriens Handicraft" sasirangan home industry. This is an experimental study, the test was conducted in the chemistry laboratory of environmental health department while the color level examination conducted at the Banjarbaru Industrial Standardization and Research Center. One way anova test with α = 0,05% was used for analyzed the data while chitosan regression statistic test with 84% deacetylation degree can be utilized as coagulant material for environmentally friendly sasirangan wastewater treatment with dose variation from 600, 650,700, 750 untill to 800 mg / lt. The highest color concentration eduction occurred at 750 mg / lt doses with 50,5% reduction and the lowest control at 650 mg/lt dose by 43%. The results showed that there were significant differences between color level and chitosan dose. Therefore, the government needs to play a significant role in sasirangan liquid waste treatment by using natural and environmentally friendly coagulant materials such as chitosan.

Enhanced Bio-Ethanol Production from Industrial Potato Waste by Statistical Medium Optimization

OpenAIRE

Izmirlioglu, Gulten; Demirci, Ali

2015-01-01

Industrial wastes are of great interest as a substrate in production of value-added products to reduce cost, while managing the waste economically and environmentally. Bio-ethanol production from industrial wastes has gained attention because of its abundance, availability, and rich carbon and nitrogen content. In this study, industrial potato waste was used as a carbon source and a medium was optimized for ethanol production by using statistical designs. The effect of various medium componen...

Pollution prevention and industrial transformation; Evoking structural changes within companies

NARCIS (Netherlands)

de Bruijn, Theo; Hofman, Peter

2000-01-01

Pollution prevention has developed as an attractive method for improving the environmental performance of companies. Often the concept is promoted in a project format, for instance in a regional perspective or for a specific sector of industry. This article analyzes the contribution of pollution

Estimation of pollution load from an industrial estate, south-western ...

African Journals Online (AJOL)

ETIM

African Journal of Environmental Science and Technology Vol. 6(2), pp. 125-129 ... up pollution control strategies and prioritization of activities. ... effective intervention. The study .... natural eco-system of the Ota industrial estate. Industrial toxic ...

The problems of water pollution: an overview

International Nuclear Information System (INIS)

Lumb, G.; Clare, A.S.

1992-01-01

Most potentially toxic chemicals eventually find their way into waterways. The most common source of this pollution is from the air. More than 50 percent of the chemical pollution of the Great Lakes is believed to come from airborne pollutants, and the main sources of this pollution are smokestacks (energy plants, nuclear or conventional; trash-to-steam incinerators; industrial factories, chemical and wood pulp) and road traffic exhaust. Chemicals may reach waterways directly through partially filtered or untreated sewage and waterway traffic, both industrial and pleasure; or they may be deposited into the soil and reach rivers and estuaries through leakage (PCBs on cables, landfills, and regular or low-level nuclear waste) or locally from fields (fertilizers, herbicides, phosphates, and other chemicals). 26 references

Magnetic particles as tracers of industrial pollution

Czech Academy of Sciences Publication Activity Database

Petrovský, Eduard; Kapička, Aleš; Jordanova, Neli; Fialová, Hana

č. 26 (2002), s. 131-132 ISSN 1590-2595. [Fundamental rock magnetism and environmental applications. Erice, 26.06.2002-01.07.2002] Institutional research plan: CEZ:AV0Z3012916 Keywords : magnetic particles * industrial pollution * fly ashes * magnetic susceptibility Subject RIV: DE - Earth Magnetism, Geodesy, Geography

Bioconversion of garden waste, kitchen waste and cow dung into value-added products using earthworm Eisenia fetida.

Science.gov (United States)

Wani, K A; Mamta; Rao, R J

2013-04-01

Solid waste management is a worldwide problem and it is becoming more and more complicated day by day due to rise in population, industrialization and changes in our life style. Transformation of industrial sludges into vermicompost is of double interest: on the one hand, a waste is converted into value added product, and, on the other, it controls a pollutant that is a consequence of increasing industrialization. Garden waste, kitchen waste and cow dung were subjected to recycle through vermicomposting by using the epigeic earthworm Eisenia fetida under field conditions. The pH, moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium in vermicompost was analysed. It was found that moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium was high in cow dung, followed by kitchen waste and garden waste. This study clearly indicates that vermicomposting of garden waste, kitchen waste and cow dung can not only produce a value added produce (vermicomposting) but at the same time reduce the quantity of waste.

Assessing heavy metal pollution in the surface soils of a region that had undergone three decades of intense industrialization and urbanization.