WorldWideScience

Sample records for industrial radiography centers

  1. Industrial radiographies

    CERN Multimedia

    2005-01-01

    The Radiation Protection group wishes to remind CERN staff responsible for contractors performing X-ray inspections on the CERN sites that the firms must apply the legislation in force in their country of origin, in particular with regard to the prevention of risks relating to ionizing radiation. Industrial radiography firms called on to work on the CERN sites must also comply with the rules laid down in CERN's Radiation Safety Manual and be registered in the relevant CERN database. Since CERN is responsible for safety on its own site, a number of additional rules have been laid down for this kind of work, as set out in Radiation Protection Procedure PRP30 https://edms.cern.ch/file/346848/LAST_RELEASED/PRP30.pdf The CERN Staff Member responsible for the contract shall register the company and issue notification that an X-ray inspection is to be performed via the web interface at the following address: http://cern.ch/rp-radio

  2. INDUSTRIAL RADIOGRAPHY COURSE, INSTRUCTORS' GUIDE. VOLUME 2.

    Science.gov (United States)

    Texas A and M Univ., College Station. Engineering Extension Service.

    INFORMATION RELATIVE TO THE LESSON PLANS IN "INDUSTRIAL RADIOGRAPHY COURSE, INSTRUCTOR'S GUIDE, VOLUME I" (VT 003 565) IS PRESENTED ON 52 INFORMATION SHEETS INCLUDING THE SUBJECTS SHIELDING EQUATIONS AND LOGARITHMS, METAL PROPERTIES, FIELD TRIP INSTRUCTIONS FOR STUDENTS, WELDING SYMBOLS AND SIZES, SAMPLE REPORT FORMS, AND TYPICAL SHIPPING…

  3. Conditions for radiation protection in industrial radiography

    CERN Document Server

    1999-01-01

    The leaflet specifies radiation protection requirements for industrial radiography in Norway. The regulations are directed towards companies using or distributing sealed radioactive sources, x-ray equipment or accelerators in non-destructive material testing (NDT). Technical requirements to the equipment, as well as administrative requirements for use, licensing, qualifications, handling of accidents etc. are given. (Author)

  4. Safety Testing of Industrial Radiography Devices

    Energy Technology Data Exchange (ETDEWEB)

    Trapp, D.J.

    1999-09-29

    The Nuclear Regulatory Commission contracted the Savannah River Technology Center to verify the relevancy of the 10 CFR Part 34 requirements for the normal use of portable gamma radiography systems and to propose recommendations for changes or modifications to the requirements.

  5. Digital radiography in the aerospace industry

    Science.gov (United States)

    Buchanan, R. A.; Bueno, C.; Barry, R. C.; Barker, M. D.

    An account is given of the bases of digital radiography (DR), with a view to the identification of NDE systems with the greatest usefulness to the aerospace industry and the nature of the advanced image processing and reconstruction techniques that have been devised thus far. The spatial resolution of any DR system is fundamentally limited by the number of pixels in the digital image and the system field-of-view. Attention is given to the problems of image geometric unsharpness and radiation quantum noise limits, as well as to the potential role of advanced DR in future NDT of aerospace components.

  6. Applications of neutron radiography for the nuclear power industry

    Energy Technology Data Exchange (ETDEWEB)

    Craft, Aaron E.; Barton, John P.

    2016-11-01

    The World Conference on Neutron Radiography (WCNR) and International Topical Meeting on Neutron Radiography (ITMNR) series have been running over 35 years. The most recent event, ITMNR-8, focused on industrial applications and was the first time this series was hosted in China. In China, more than twenty new nuclear power plants are in construction and plans have been announced to increase the nuclear capacity further by a factor of three within fifteen years. There are additional prospects in many other nations. Neutron tests were vital during previous developments of materials and components for nuclear power applications, as reported in this conference series. For example a majority of the 140 papers in the Proceedings of the First WCNR are for the benefit of the nuclear power industry. Included are reviews of the diverse techniques being applied in Europe, Japan, the United States, and at many other centers. Many of those techniques are being utilized and advanced to the present time. Neutron radiography of irradiated nuclear fuel provides more comprehensive information about the internal condition of irradiated nuclear fuel than any other non-destructive technique to date. Applications include examination of nuclear waste, nuclear fuels, cladding, control elements, and other critical components. In this paper, the techniques developed and applied internationally for the nuclear power industry since the earliest years are reviewed, and the question is asked whether neutron test techniques can be of value in development of the present and future generations of nuclear power plants world-wide.

  7. Saferad industrial radiography system; Sistema Saferad de radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Wallace Aparecido de [NDT do Brasil Ltda., Sao Paulo, SP (Brazil)

    2005-07-01

    The Saferad industrial radiography system is a system for execution of radiographic tests that provide small rays of insulation compared to conventional techniques. The system consists of a special irradiator that can be operated in three modes of exposure: Projection, Directional, and Panoramic with a set of collimators for different diameters of tubes, which collimate the radiation only to the area of the film. The radioisotope used is Selenium-75. Complements the system the shielding GammaBlok, polymer based on cadmium, flexible, non-toxic, and presented in various dimensions and shapes. It should involve the radiographic arrangement to shield the radiation after it goes through the film and the scattered radiation.

  8. Human performance analysis of industrial radiography radiation exposure events

    Energy Technology Data Exchange (ETDEWEB)

    Reece, W.J.; Hill, S.G.

    1995-12-01

    A set of radiation overexposure event reports were reviewed as part of a program to examine human performance in industrial radiography for the US Nuclear Regulatory Commission. Incident records for a seven year period were retrieved from an event database. Ninety-five exposure events were initially categorized and sorted for further analysis. Descriptive models were applied to a subset of severe overexposure events. Modeling included: (1) operational sequence tables to outline the key human actions and interactions with equipment, (2) human reliability event trees, (3) an application of an information processing failures model, and (4) an extrapolated use of the error influences and effects diagram. Results of the modeling analyses provided insights into the industrial radiography task and suggested areas for further action and study to decrease overexposures.

  9. Industrial Assessment Center Program

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Dereje Agonafer

    2007-11-30

    The work described in this report was performed under the direction of the Industrial Assessment Center (IAC) at University of Texas at Arlington. The IAC at The University of Texas at Arlington is managed by Rutgers University under agreement with the United States Department of Energy Office of Industrial Technology, which financially supports the program. The objective of the IAC is to identify, evaluate, and recommend, through analysis of an industrial plant’s operations, opportunities to conserve energy and prevent pollution, thereby reducing the associated costs. IAC team members visit and survey the plant. Based upon observations made in the plant, preventive/corrective actions are recommended. At all times we try to offer specific and quantitative recommendations of cost savings, energy conservation, and pollution prevention to the plants we serve.

  10. Occupational doses simulation in industrial radiography; Simulacao de doses ocupacionais em radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, Pedro B.; Falcao, Rossana C.; Facure, Alexandre [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)]. E-mail: pbarbosa@cnen.gov.br; ross@cnen.gov.br; afsoares@cnen.gov.br; Hunt, John [Instituto de Radioprotecao e Dosimetria (IRD), Rio de Janeiro, RJ (Brazil)]. E-mail: john@ird.gov.br; Silva, Ademir X. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia Nuclear]. E-mail: ademir@com.ufrj.br

    2005-07-01

    The application of ionizing radiation in industrial processes is assuming an important role in the national scenario. Industrial radiography is one of the more used techniques in the nondestructive assays. This type of radiography can be carried out through X or gamma rays, and in about ninety percent of the cases this procedure it is carried out using 192 Ir sources, which is a gamma with average energy of 380 keV. This practice is called Gammagraphy. The Brazilian regulation Norm CNEN-NN-6.04 of the Nuclear National Energy Commission (CNEN), determines that works of Industrial Radiography in urban, suburban and agricultural areas, where there is presence of the public in general, to follow the recommendations of an specific radioprotection guide. The operations in these urban zones cannot cause over expositions to the operators as well as to the public. The present work presents the first step in order to simulate occupational doses in urban zones. Occupational doses were simulated and an intercomparison was made between the Monte Carlo Codes VMC and MCNP, with the objective of testing the viability of using the first code, which was developed at CNEN, to simulate values of occupational doses in situations of routine and emergency exposures, in real time. (author)

  11. FMEA Based Risk Assessment of Component Failure Modes in Industrial Radiography

    CERN Document Server

    Pandey, Alok; Sonawane, A U; Rawat, Prashant S

    2016-01-01

    Industrial radiography has its inimitable role in non-destructive examinations. Industrial radiography devices, consisting of significantly high activity of the radioisotopes, are operated manually by remotely held control unit. Malfunctioning of these devices may cause potential exposure to the operator and nearby public, and thus should be practiced under a systematic risk control. To ensure the radiation safety, proactive risk assessment should be implemented. Risk assessment in industrial radiography using the Failure Modes & Effect Analysis (FMEA) for the design and operation of industrial radiography exposure devices has been carried out in this study. Total 56 component failure modes were identified and Risk Priority Numbers (RPNs) were assigned by the FMEA expert team, based on the field experience and reported failure data of various components. Results shows all the identified failure modes have RPN in the range of 04 to 216 and most of the higher RPN are due to low detectability and high severi...

  12. Radiological protection procedures for industrial applications of computed radiography; Procedimentos de protecao radiologica em aplicacoes industriais da radiografia computadorizada

    Energy Technology Data Exchange (ETDEWEB)

    Aquino, Josilto Oliveira de

    2009-03-15

    Due to its very particular characteristics, industrial radiography is responsible for roughly half of the relevant accidents in nuclear industry, in developed as well as in developing countries, according to the International Atomic Energy Agency (IAEA). Thus, safety and radiological protection in industrial gamma radiography have been receiving especial treatment by regulatory authorities of most Member States. The main objective of the present work was to evaluate, from the radioprotection point of view, the main advantages of computed radiography (CR) for filmless industrial radiography. In order to accomplish this, both techniques, i.e. conventional and filmless computed radiography were evaluated and compared through practical studies. After the studies performed at the present work it was concluded that computed radiography significantly reduces the inherent doses, reflecting in smaller restricted areas and costs, with consequent improvement in radiological protection and safety. (author)

  13. Forging an Industrial Center

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Ningdong Development Zone, an important national-level base for the coal and chemical industries, is located in the eastern part of Yinchuan, capital of Ningxia Hui Autonomous Region. It is an energy development base for transforming electricity from west to east in the country and a trial base for promoting a cyclic economy.

  14. Working safely in gamma radiography. A training manual for industrial radiographers

    Energy Technology Data Exchange (ETDEWEB)

    McGuire, S.A.; Peabody, C.A.

    1982-09-01

    This manual is designed for classroom training in working safely in industrial radiography using gamma sources. The purpose is to train radiographers' assistants to work safely as a qualified gamma radiographer. The contents cover the essentials of radiation, radiation protection, emergency procedures, gamma cameras, and biological effects of radiation. (ACR)

  15. Industrial radiography in the State of Bahia, Brazil The health protection of workers

    CERN Document Server

    Andrade, A E O D

    1997-01-01

    This study aimed to identify the Regulatory and Inspection Authority for actions developed by industrial radiography enterprises in the State of Bahia, Brazil, concerning health protection of workers exposed to ionizing radiation in industry. Institutions which legislate about this matter at international, national and State level were identified. These legislations were analysed according to recommendations by the Basic Safety Standards from the Atomic Energy International Agency. Medical Supervision is proposed as a factor to warrant protection to worker's health. This is a service evaluation study, encompassing results, processes and structural components. Emphasis is given to the process component which investigated the adequacy of which is performed by employees and workers. Five enterprises which provide industrial radiography services in the State of Bahia were identified, employing forty workers on a temporary basis. This study also observed: intense workforce, a complete process of contracting out in...

  16. Radiation safety aspects in application of isotopes for industrial radiography in Bangladesh

    Energy Technology Data Exchange (ETDEWEB)

    Bakht, D. [Titas Gas Transmission and Distribution Company, Dhaka (Bangladesh)

    1997-10-01

    Industrial Radiography arose out of the widespread applications of X-rays pioneered by Roentgen about 100 years back. It is routinely used in studying the integrity of structural materials and like most countries in the world, its use in Bangladesh is increasing at a faster rate. This is because Bangladesh is a developing country of 3rd world and in the backdrop of agrarian poverty ridden economy, its population may exceed 125 millions by 2000 AD, leaving some 12 millions people unemployed. To support them, therefore, immense activities are activated in different sectors. Accordingly, increasing importance on NDT is given and in most cases particular application of Gamma radiography is preferred using Iridium Isotope Ir-192. Consequently the points of implications of isotopes are in Open Field and Inservice Inspection Radiography, Handling of Radiation Emergencies, Safe Transport of Radioactive Materials and Hazardous Effects and Risk of Ionizing Radiation, etc. Accordingly over exposure of Ir-192 Radionuclides, Accidents and Unusual Occurrences: Case Studies, Training Courses on Safety and Regulation of Sealed Sources, Licenses for Radiography Operation including Safe Disposal of Isotopes are the salient issues to be viewed in appropriate perspectives. The role played by Bangladesh Atomic Energy Commission and Bangladesh Society for NDT in collaboration with other members of the international committee for NDT are furthering the safe industrialization process

  17. Tests of cosmic ray radiography for power industry applications

    CERN Document Server

    Durham, J M; Morris, C L; Bacon, J; Fabritius, J; Fellows, S; Plaud-Ramos, K; Poulson, D; Renshaw, J

    2015-01-01

    In this report, we assess muon multiple scattering tomography as a non-destructive inspection technique in several typical areas of interest to the nuclear power industry, including monitoring concrete degradation, gate valve conditions, and pipe wall thickness. This work is motivated by the need for radiographic methods that do not require the licensing, training, and safety controls of x-rays, and by the need to be able to penetrate considerable overburden to examine internal details of components that are otherwise inaccessible, with minimum impact on industrial operations. In some scenarios, we find that muon tomography may be an attractive alternative to more typical measurements.

  18. Tests of cosmic ray radiography for power industry applications

    Directory of Open Access Journals (Sweden)

    J. M. Durham

    2015-06-01

    Full Text Available In this report, we assess muon multiple scattering tomography as a non-destructive inspection technique in several typical areas of interest to the nuclear power industry, including monitoring concrete degradation, gate valve conditions, and pipe wall thickness. This work is motivated by the need for imaging methods that do not require the licensing, training, and safety controls of x-rays, and by the need to be able to penetrate considerable overburden to examine internal details of components that are otherwise inaccessible, with minimum impact on industrial operations. In some scenarios, we find that muon tomography may be an attractive alternative to more typical measurements.

  19. Tests of cosmic ray radiography for power industry applications

    Energy Technology Data Exchange (ETDEWEB)

    Durham, J. M., E-mail: durham@lanl.gov; Guardincerri, E.; Morris, C. L.; Bacon, J.; Fabritius, J.; Fellows, S.; Poulson, D.; Plaud-Ramos, K. [Los Alamos National Laboratory, Los Alamos, NM 87544 (United States); Renshaw, J. [Electric Power Research Institute, Charlotte, NC 28262-8550 (United States)

    2015-06-15

    In this report, we assess muon multiple scattering tomography as a non-destructive inspection technique in several typical areas of interest to the nuclear power industry, including monitoring concrete degradation, gate valve conditions, and pipe wall thickness. This work is motivated by the need for imaging methods that do not require the licensing, training, and safety controls of x-rays, and by the need to be able to penetrate considerable overburden to examine internal details of components that are otherwise inaccessible, with minimum impact on industrial operations. In some scenarios, we find that muon tomography may be an attractive alternative to more typical measurements.

  20. Assessment and prevention of the professional risks in the operations of industrial radiography; Evaluation et prevention des risques professionnels dans les operations de radiographie industrielle

    Energy Technology Data Exchange (ETDEWEB)

    Pizzorno, M.; Paul, D.; Coletti, F.; Sari Minodier, I.; Azzopardi, G.; Klemenic, O.; Botta, A. [Aix-Marseille-2 Univ., Lab. de Biogenotoxicologie et Mutagenese Environnementale (EA 1784 - IFR PMSE 112) Faculte de Medecine, 13 - Marseille (France)

    2006-07-01

    Industrial radiography is a nocturnal activity, hazardous and little known; it is among the professions the most exposed to ionizing radiation. This study analyse the doses, received the industrial radiographers, their workplace conditions and organization of their tasks. Dosimetry observations on site, together with calculations using the Mercurad code, allowed mean values for reference doses for all the work (including transport, gammatron manipulation, collimator manipulation, shooting) to be established. These value were integrated into a table entitled 'reference doses' in order to provisionally evaluate the doses received by the operators. Distances for security zone demarcation, so as to forbid access to non exposed personnel during shooting, were evaluated. Assessment of the professional risks for industrial radiography, taking into account all the risks (radiological and others), has been made and is under evaluation. This led to measures for prevention based on the material used (collimator, tripod, gamma-stops), on the organization and the conditions of work (for example, time limits permitting a prior visit to the site and preparation for radiography, suitable scaffolding, sufficient lighting, siting of shootings). These prevention measure will be integrated into the new charter of good practice in industrial radiography in the Provence Alpes Cote d'Azur region (south of France). (authors)

  1. Industrial radiography with cosmic-ray muons: A progress report

    Science.gov (United States)

    Gilboy, W. B.; Jenneson, P. M.; Simons, S. J. R.; Stanley, S. J.; Rhodes, D.

    2007-09-01

    Cosmic-ray produced muons arrive at the surface of the earth with enormous energies ranging up to 1012 GeV. There have been sporadic attempts to exploit their extreme penetration through matter to probe the internal structures of very large objects, including an Egyptian pyramid and a volcano but their very low intensity per unit area ( ≈1 cm-2 per min) generally restricts the practicably attainable spatial resolution to large dimensions. Nevertheless the more intense low energy region of the muon spectrum has recently been shown to be capable of detecting high-Z objects with dimensions of the order of 10 cm hidden inside large transport containers in measurement times of minutes. These various developments have encouraged further studies of potential industrial uses of cosmic-ray muons in industrial applications. In order to gain maximum benefit from the low muon flux large area detectors are required and plastic scintillators offer useful advantages in size, cost and simplicity. Scintillator slabs up to 1 m2 square and 76.2 mm thick are undergoing testing for applications in the nuclear industry. The most direct approach employs photomultiplier tubes at each corner to measure the relative sizes of muon induced pulses to determine the location of each muon track passing through the scintillator. The performance of this technique is reported and its imaging potential is assessed.

  2. Radiation protection analysis in open facilities of industrial radiography; Analise da radioprotecao em instalacoes abertas de radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Leocadio, Joao C.; Tauhata, Luiz [Instituto de Radioprotecao e Dosimetria (IRD), Rio de Janeiro, RJ (Brazil); Crispim, Verginia R. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia Nuclear

    1999-11-01

    This work had the objective to analyze the open facilities or mobile industrial radiography to obtain the distribution of doses in the radiographers, to evaluate the radiological conditions and the operational procedures, besides to present proposed for the reference levels and to esteem the potential exposure. The results of the additional monitoring revealed an improvement of the radiation protection conditions in the open facilities and the risk of potential exposure was reduced. With relationship to the radiation protection procedures, the accompaniment of the radiographic testing verified that most of the problems was solved. The advantage of the proposed reference levels is that the supervisors would enlarge the frequency of audits to accomplish the investigations and interventions. The mobile industrial radiography with bunkers presented distributions with 95% of the doses below 0,2 mSv and interventions. The mobile industrial radiography with bunkers presented distributions with 95% of the doses below 0,2 mSv and the distributions of the facilities with cordoned area they had 75% of the doses below 0,4 mSv. (author) 10 refs., 2 figs., 4 tabs.

  3. An industrial radiography exposure device based on measurement of transmitted gamma-ray intensity

    Science.gov (United States)

    Polee, C.; Chankow, N.; Srisatit, S.; Thong-Aram, D.

    2015-05-01

    In film radiography, underexposure and overexposure may happen particularly when lacking information of specimen material and hollowness. This paper describes a method and a device for determining exposure in industrial gamma-ray radiography based on quick measurement of transmitted gamma-ray intensity with a small detector. Application software was developed for Android mobile phone to remotely control the device and to display counting data via Bluetooth communication. Prior to film exposure, the device is placed behind a specimen to measure transmitted intensity which is inversely proportional to the exposure. Unlike in using the conventional exposure curve, correction factors for source decay, source-to- film distance, specimen thickness and kind of material are not needed. The developed technique and device make radiographic process economic, convenient and more reliable.

  4. Monte Carlo applied to calculation of shields of facilities used in industrial radiography; Monte Carlo aplicado al calculo de blindajes de instalaciones usadas en radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Martinez Ovalle, S. A.; Olaya Davila, H.; Reyes Caballero, F.

    2013-07-01

    The main objective of this work is to verify through Monte Carlo, the dimensions most appropriate in the shielding of an installation designed for Industrial radiography with a Co-60 Irradiator. (Author)

  5. Industrial Assessment Center (IAC) Operations Manual

    Energy Technology Data Exchange (ETDEWEB)

    Gopalakrishnan, Bhaskaran [West Virginia Univ., Morgantown, WV (United States); Nimbalkar, Sachin U. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wenning, Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Thirumaran, Kiran [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-04-01

    IAC Operations Manual describes organizational model and operations of the Industrial Assessment Center (IAC), Center management activities, typical process of energy assessment, and energy assessment data for specific industry sectors.

  6. SisRadiologia: a new software tool for analysis of radiological accidents and incidents in industrial radiography

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Camila M. Araujo; Silva, Francisco C.A. da, E-mail: araujocamila@yahoo.com.br, E-mail: dasilva@ird.gov.br [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Araujo, Rilton A., E-mail: consultoria@maximindustrial.com.br [Maxim Industrial Assessoria TI, Rio de Janeiro, RJ (Brazil)

    2013-07-01

    According to the International Atomic Energy Agency (IAEA), many efforts have been made by Member states, aiming a better control of radioactive sources. Accidents mostly happened in practices named as high radiological risk and classified by IAEA in categories 1 and 2, being highlighted those related to radiotherapy, large irradiators and industrial radiography. Worldwide, more than 40 radiological accidents have been recorded in the industrial radiography. Worldwide, more than 40 radiological accidents have been recorded in the industrial radiography area, involving 37 workers, 110 members of the public and 12 fatalities. Records display 5 severe radiological accidents in industrial radiography activities in Brazil, in which 7 workers and 19 members of the public were involved. Such events led to hands and fingers radiodermatitis, but to no death occurrence. The purpose of this study is to present a computational program that allows the data acquisition and recording in the company, in such a way to ease a further detailed analysis of radiological event, besides providing the learning cornerstones aiming the avoidance of future occurrences. After one year of the 'Industrial SisRadiologia' computational program application - and mostly based upon the workshop about Analysis and Dose Calculation of Radiological Accidents in Industrial Radiography (Workshop sobre Analise e Calculo de dose de acidentes Radiologicos em Radiografia Industrial - IRD 2012), in which several Radiation Protection officers took part - it can be concluded that the computational program is a powerful tool to data acquisition, as well as, to accidents and incidents events recording and surveying in Industrial Radiography. The program proved to be efficient in the report elaboration to the Brazilian Regulatory Authority, and very useful in workers training to fix the lessons learned from radiological events.

  7. Bright flash neutron radiography capability of the research reactor at the McClellan Nuclear Research Center

    Energy Technology Data Exchange (ETDEWEB)

    Tremsin, A.S., E-mail: ast@ssl.berkeley.edu [University of California at Berkeley, Berkeley, CA 94720 (United States); Lerche, M. [McClellan Nuclear Research Center, 5335 Price Avenue Building 258, McClellan, CA 95652 (United States); Schillinger, B. [Forschungsreaktor FRM-II, Technische Universität München, D-85747 Garching (Germany); Feller, W.B. [NOVA Scientific, Inc., 10 Picker Road, Sturbridge, MA 01566 (United States)

    2014-06-01

    The capability to produce a bright, short neutron pulse at the McClellan Nuclear Research Center (MNRC) can be very attractive for some neutron imaging applications. Complementary to conventional thermal neutron radiography conducted at the reactor, operating at the average power of 1 MW, a short pulse of ∼25 ms FWHM duration can be produced at MNRC with the peak power exceeding 350 MW. Combination of a fast thermal neutron counting detector with a short neutron pulse at MNRC, enables high-resolution stroboscopic imaging to complement conventional neutron radiography. The results presented in this paper demonstrate the MNRC capabilities for conducting conventional thermal neutron radiography, demonstrating imaging spatial resolution below 100 μm, as well as bright flash neutron radiography with multiple nearly simultaneous events detected with microsecond timing resolution.

  8. New X-ray testing methods of aerosol products for industrial radiography

    Science.gov (United States)

    Bozydar Knyziak, Adrian; Rzodkiewicz, Witold; Kaczorowska, Ewa; Derlacinski, Michal

    2017-02-01

    An amount of product in e.g. an aerosol canister is not difficult to estimate by weighing a filled can and subtracting the tare of packaging. In this way, we can obtain the net weight of the ingredients present in the can. Although, this does not indicate the volumetric content. Therefore, in the paper, the fundamental (the weight method and given by FEICA) and new methods (given by authors) related to the determination of the volumetric content of canister filled with aeorosol products are presented. The new methods are based on direct digital radiography (DR) using X-ray radiation. For the needs of new methods, the X-ray CCD-DR imaging system was built and developed in our Laboratory in Department of Radiation and Vibration at the Central Office of Measures. For comparison purposes, with regard to the volumetric content, a lot of metal cans of capacities 140, 185, 450, 700 ml were inspected. In future, computed tomography (CT) for industrial radiography in our laboratory will be used. Currently, an algorithm for CT is being tested. It will give us possibility for very precise measurements to determine volumetric content of examined canisters.

  9. Planning the recovery of an industrial radiography source which fails to return to its storage container

    Energy Technology Data Exchange (ETDEWEB)

    Hockings, C. [Qantas Airways, Sydney, NSW (Australia)

    1998-11-01

    Effective planning is fundamental to the safe use of radioactive materials. Such planning must include the safe recovery of the radioactive material in the event of an accident. This discussion is restricted to the application of radioactive material for industrial radiography using conventional source projectors and containers. Site operators of such equipment are required by New South Wales law to be trained to a minimum standard and licensed. However the infrequency of practicing recovery procedures or the absence of a recovery plan entirely, provides scope for inappropriate responses by an operator in an accident situation. The plan described here uses a flow chart approach to guide the operator through the decision required at such a time. A review of earlier accidents is also included

  10. Defect detection in industrial radiography: a multi-scale approach; Detection de defauts en radiographie industrielle: approches multiechelles

    Energy Technology Data Exchange (ETDEWEB)

    Lefevre, M.

    1995-10-01

    Radiography is used by Electricite de France for pipe inspection in nuclear power plant in order to detect defects. For several years, the RD Division of EDF has undertaken research to define image processing methods well adapted to radiographic images. The main issues raised by these images are their low contrast, their high level of noise, the presence of a trend and the variable size of the defects. A data base of digitized radiographs of pipes has been gathered and the statistical, topological and geometrical properties of all of these images have been analyzed. From this study, a global indicator of the presence of defects and local features, leading to a classification of images into areas with or without defects, have been extracted. The defect localisation problem has been considered in a multi-scale framework based on the creation of a family of images with increasing regularity and defined as a solution of a partial differential equation. From a choice of axioms, a set of equations may be deduced which define various multi-scale analyses. The survey of the properties of such analysed, when applied to images altered with different types of noise, has lead to the selection of the digitized radiographs best adapted multi-scale analysis. The segmentation process, uses the geodesic information attached to defects via connection cost concept. The final decision is based on a summary of the information extracted at several scales. A fuzzy logic approach has been proposed to solve this part. We then developed methods and tools for expertise guidance and validated them on a complete data base of images. Some global indicators have been extracted and a detection and localisation process has been achieved for large defects. (author). 117 refs., 73 figs.

  11. Industrial Assessment Center Program Impact Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Martin, M.A.

    2000-01-26

    This report presents the results of an evaluation of the U.S. Department of Energy's Industrial Assessment Center (IAC) Program. The purpose of this program is to conduct energy, waste, and productivity assessments for small to medium-sized industrial firms. Assessments are conducted by 30 university-based industrial assessment centers. The purpose of this project was to evaluate energy and cost savings attributable to the assessments, the trained alumni, and the Websites sponsored by this program. How IAC assessments, alumni, and Web-based information may influence industrial energy efficiency decision making was also studied. It is concluded that appreciable energy and cost savings may be attributed to the IAC Program and that the IAC Program has resulted in more active and improved energy-efficiency decision making by industrial firms.

  12. Weld Inspection Based on Radiography Image Segmentation with Level Set Active Contour Guided Off-Center Saliency Map

    Directory of Open Access Journals (Sweden)

    Mohamed Ben Gharsallah

    2015-01-01

    Full Text Available Radiography is one of the most used techniques in weld defect inspection. Weld defect detection becomes a complex task when uneven illumination and low contrast characterize radiographic images. In this paper we propose a new active contour based level set method for weld defect detection in radiography images. An off-center saliency map exploited as a feature to represent image pixels is embedded into a region energy minimization function to guide the level set active contour to defects boundaries. The aim behind using salient feature is that a small defect can frequently attract attention of human eyes which permits enhancing defects in low contrasted image. Experiment results on different weld radiographic images with various kinds of defects show robustness and good performance of the proposed approach comparing with other segmentation methods.

  13. Local liquid velocity measurement of Trickle Bed Reactor using Digital Industrial X-ray Radiography

    Science.gov (United States)

    Mohd Salleh, Khairul Anuar

    Trickle Bed Reactors (TBRs) are fixed beds of particles in which both liquid and gas flow concurrently downward. They are widely used to produce not only fuels but also lubrication products. The measurement and the knowledge of local liquid velocities (VLL) in TBRs is less which is essential for advancing the understanding of its hydrodynamics and for validation computational fluid dynamics (CFD). Therefore, this work focused on developing a new, non-invasive, statistically reliable technique that can be used to measure local liquid velocity (VLL) in two-dimensions (2-D). This is performed by combining Digital Industrial X-ray Radiography (DIR) and Particle Tracking Velocimetry (PTV) techniques. This work also make possible the development of three-dimensional (3-D) VLL measurements that can be taken in TBRs. Measurements taken through both the combined and the novel technique, once validated, were found to be comparable to another technique (a two-point fiber optical probe) currently being developed at Missouri University of Science and Technology. The results from this study indicate that, for a gas-liquid-solid type bed, the measured VLL can have a maximum range that is between 35 and 51 times that of its superficial liquid velocity (VSL). Without the existence of gas, the measured VLL can have a maximum range that is between 4 and 4.7 times that of its VSL. At a higher V SL, the particle tracer was greatly distributed and became carried away by a high liquid flow rate. Neither the variance nor the range of measured VLL varied for any of the replications, confirming the reproducibility of the experimental measurements used, regardless of the VSL . The liquid's movement inside the pore was consistent with findings from previous studies that used various techniques.

  14. Reading Problems in an Industrial Information Center

    Science.gov (United States)

    Northcott, Jean

    1972-01-01

    An important function of an industrial information center is to control, not multiply, the reading problem by selective use of available commercial services. When necessary, and economically feasible, specialized internal services are developed. Some of these services are described. (6 references) (Author)

  15. Research and industrial applications at the McClellan Nuclear Research Center, University of California, Davis

    Energy Technology Data Exchange (ETDEWEB)

    Klein, B.; Lerche, M.; Shackelford, J.; Steingass, W., E-mail: mlerche@ucdavis.edu [Univ. of California, Davis, McClellan Nuclear Research Center, Davis CA (United States)

    2011-07-01

    The MNRC is a facility centered around a 2 MW TRIGA research reactor, one of the three largest university research reactors in the US and the youngest. A wide range of research studies is underway including the imaging of fuel cells, tomography of geological minerals, neutron activation analysis of biological samples and plant seed irradiation. Industrial applications include radiography of precision aerospace castings and irradiation of electronics. The McClellan reactor may become part of a consortium of university reactors that will provide radiopharmaceuticals in response to a critical shortage in North America.

  16. 14 CFR 1201.402 - NASA Industrial Applications Centers.

    Science.gov (United States)

    2010-01-01

    ... ORGANIZATION AND GENERAL INFORMATION General Information § 1201.402 NASA Industrial Applications Centers. (a... development organizations. Using computers, the NASA Industrial Applications Centers conduct retrospective and... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false NASA Industrial Applications Centers. 1201...

  17. Performance evaluation of the conventional Brazilian industries radiation protection in the small industrial gauges and industrial radiography areas; Sistema de avaliacao de desempenho em radioprotecao das industrias convencionais brasileiras nas areas de medidores nucleares e radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Joyra Amaral dos

    1999-08-01

    This works evaluates by punctuation the performance in conventional Brazilian industries radiation protection area which make use of small industrial gauges and industrial radiography. It proposes, procedures for industry self-evaluation, besides a new radiation protection plans pattern for the small industrial gauges area. The data source where inspection reports of Dosimetry Radiation Protection Institute/Nuclear Energy Commission conventional Brazilian industries' radiation protection plans, beyond visitation to the inspection place. The performance evaluation has been realized both in the administrative and operational aspects of the industries. About of 60% of the industries have a satisfactory register control which does not happen to the operational control. The performance evaluation advantage is that industries may self-evaluate, foreseeing Dosimetry Radiation Protection Institute's regulation inspections, correcting its irregularities, automatically improving its services. The number of industries which have obtained satisfactory performance in both areas is below 70%, both in administrative and operational aspects. Such number can be considered a low one as it is radiation protection. The procedures propose in this work aim to improve such a situation. (author)

  18. Characterization of mono-ethylene-glycol based industrial polyurethanes samples by fast-neutron radiography and neutron tomography

    Science.gov (United States)

    Rogante, Massimo; Söllradl, Stefan

    2016-09-01

    A complicated structural organization of polyurethanes may have a strong influence on the materials functional properties. Under particular conditions such as mechanical and thermal loading and aging, it leads to the material degradation, even in fresh-prepared bulk polymers and especially if defects are present in the material. Unwanted bubbles can be observed, which form during the expansion of the mixture during its chemical reaction and remain present in the final product. These macro-, micro- and nano-bubbles influence the material's performance. In this work, neutron radiography and tomography have been adopted to characterize at a macro-scale level the bulk of commercially available polyurethane samples, obtained from dissimilar- mixture ratios with different densities and branching levels as well as from different zones of the production mould. The characterisation allowed an estimation of the different dense materials - as they are used, e.g., in soles of shoes - as well as the invisible defects like pores and cracks, responsible for the materials fracture by mechanical loading. The obtained information are expected to be useful for various industrial sectors such as automotive and footwear industry. It will be completed by applying SANS, which has already proved to characterize the microstructure of the bulk-polymer with respect to nano-pores, micro-cracks and their arrangement in the polymer matrix.

  19. Reconstructive dosimetry of radiological accidents - study of a brazilian case of industrial gamma radiography; Dosimetria reconstrutiva de acidentes radiologicos - estudo de um caso brasileiro de gamagrafia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Francisco Cesar Augusto da; Hunt, John G.; Ramalho, Adriana [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Pinto, Livia M.F. Amalfi [ARCtest - Servicos Tecnicos de Inspecao e Manutencao Industrial Ltda., Paulinia, SP (Brazil)]. E-mail: protecao@arctest.com.br

    2002-07-01

    On May 2000, an industrial gamma radiography operator, during a maintenance work of a {sup 60}Co irradiator, has suffered a radiological accident with severe consequences to the left hand. The experts of the High Doses Analysis Group (GADE/IRD/CNEN) initiated the reconstructive dosimetry for the radiation dose estimation, in order to determine the real dose received by the operator, and to help the medical evaluation for prescribing the medical procedures for treatment of the involved victim. This paper presents the reconstructive dosimetry performed through the determination of the radiation doses of the operator, based on theoretical, experimental and computational methods. For the computer methods, a program for the calculation of external doses were used, based on the Monte Carlo method, and a human body simulator composed by voxels. The values of effective and equivalent doses are also presented which has caused severe lesions on the operator hand.

  20. Evaluation of X-Ray Protective Measurements in Intraoral Radiography Equipped Centers in Yazd

    Directory of Open Access Journals (Sweden)

    D.Goodarzi Pour

    2005-02-01

    Full Text Available Statement of Problem: A few decades have past from using radiographic technology as an accurate paraclinical method and always protective measurements is applicated against ionizing radiation. As dentalradiography is a routine procedure in dentistry the importance of protective strategies is clear.Propose: The aim of this descriptive study is to evaluate the protection principles in centers which haveintraoral radiographic devices in Yazd.Material and Methods: We have considered all three aspects of practitioner, environment and patientprotection using questionnaire and visiting those centers.Results: 33/7% of dental offices ,10 clinics ,3 institution and faculty of dentistry had intraoral radiographicequipments. Stablishment of protection principles for radiographer was favorable. 7.7% of centers had x-ray room with leaded walls, 23.1% had curtain , in 69/2% of centers radiographers stood in correct position anddistance while taking radiograph. Regarding to protection of environment, beams leakage control in 23.1% dental offices, 70% of clinics, all institution and faculty of dentistry have done.Conclusion: Non of the centers used rectangular localizator, thyroid shield, film holder and just some centers used leaded apron in specific circumstances. We have concluded that patient protection constitute less consideration. Generally lack of protective consideration is related to deficient knowledge of operators. Lackof information about protection equipments causes decrease of demanding of these tools and ultimately lack of these equipments in the market.

  1. A Compact 5 MeV S-Band Electron Linac Based X-Ray Source for Industrial Radiography

    CERN Document Server

    Auditore, Lucrezia; De Pasquale, Domenico; Emanuele, Umberto; Italiano, Antonio; Trifirò, Antonio; Trimarchi, Marina

    2005-01-01

    A compact and reliable X-ray source, based on a 5 MeV, 1 kW, S-band electron linac, has been set up at the Dipartimento di Fisica, Universit\\'a di Messina. This source, coupled with a GOS scintillator screen and a CCD camera, represents an innovative transportable system for industrial radiography and X-ray tomography. Optimization of the parameters influencing the e-gamma conversion and the X-ray beam characteristics have been studied by means of the MCNP-4C2 code. The converter choice is the result of the study of the e-gamma conversion performances for different materials and materials thicknesses. Also the converter position with respect to the linac exit window was studied. The chosen converter consists in a Ta-Cu target inserted close to the linac window. The Cu layer acts as a filter both on the electrons from the source and on the low energy X-rays. The X-ray beam angular profile was studied by means of GafChromic films with and without collimation. In the final source project, a collimation system pr...

  2. Evaluation of X-Ray Protective Measurements in Intraoral Radiography Equipped Centers in Yazd

    OpenAIRE

    D.Goodarzi Pour; S.Ebrahimi Moghaddam

    2005-01-01

    Statement of Problem: A few decades have past from using radiographic technology as an accurate paraclinical method and always protective measurements is applicated against ionizing radiation. As dentalradiography is a routine procedure in dentistry the importance of protective strategies is clear.Propose: The aim of this descriptive study is to evaluate the protection principles in centers which haveintraoral radiographic devices in Yazd.Material and Methods: We have considered all three asp...

  3. The industrial radiography service in Brazil concerning to the radiation protection aspect; O servico de radiografia industrial no Brasil sob o aspecto da protecao radiologica

    Energy Technology Data Exchange (ETDEWEB)

    Martins, M.M.

    1994-12-31

    A study about the industrial radiography situation in Brazil, concerning to the radiation protection aspects is shown. With this purpose it was made an inventory, with utilization of the file of facilities officially registered in industrial application from Brazilian Nuclear Energy Commission (CNEN). It was evaluated the quantity of accelerators, radiation monitors and radiation workers (health physics, operator). As quality and performance indicators of radiation protection the mean doses and the collective doses were used, and their variation from 1987 to 1990. As deficiency signals of radiological protection programs and procedures were utilized the 175 abnormal event occurred (radiological accident and emergency situation) from 1976 to 1992, after an analysis of their causes. The results showed that, for around 2000 monitored workers, the mean dose equivalent was between 0.83 to 2.70 mSv, and the collective dose, between 1.54 and 6.18 Sv.man, from 1987 to 1990. In this period, it was verified a tendency for reduction of means dose and collective dose values. It indicates a possible improvement of radiation protection services or an influence of economical situation of the country. From 175 abnormal events analysed, 456 persons were exposed, with 7.2% of them receiving doses above 50 mSv. These results were compared with those from others countries, such as United Kingdom and united States. (author). 76 refs, 16 figs, 24 tabs.

  4. The Evaluation of Bacterial Contamination of Active Radiography Apparatus in Dental Centers of Hamadan City

    Directory of Open Access Journals (Sweden)

    A. Eskandarloo

    2006-01-01

    Full Text Available Introduction & Objective: During the most dental procedures, contamination of devices with blood, saliva and other body fluids, which is the most important factor for transmission of infectious diseases, is inevitable. Therefore principles of infection control should be carefully considered in the dentistry. The purpose of this study was the evaluation of bacterial contamination of active radiographic apparatus in dental centers of Hamadan city in year 2003. Materials & Methods : In this cross-sectional study 37 radiographic apparatus in dental centers of Hamadan were evaluated. Samples were collected from four area (25 cm2 each that are frequently touched by dentists, personnel, etc. using a swab. The swab was inserted into the carrier media containing thioglycolate, a smear was obtained from the solution and remaining solution was cultured in blood agar. Smear and blood agar cultures were transferred to microbiology lab to determine bacterial contamination level as well as bacterial typing. According to WHO criteria the area which has more than 10 microorganism/cm2 is considered as contaminated. Results: It was found that 13 of radiographic apparatus(35% were contaminated, the most frequent bacterial type detected in this study was micrococcus (75.7% and the least were enterobacter and nocardia (2.7% each. Antiseptic materials used for decontamination of the devices were as follow : Alcohol (43.2% , Deconex (32.4% , Micro10 (18.9% , Savlon (10.8% , Hypochlorid (5.4% , Glutaraldehyde (2.7%. Conclusion: Based on the results (35% bacterial contamination it can be concluded that careful performance of infection control principles, daily decontamination of devices and offering periodic instructions for dental personnel are essential.

  5. Training Center for Industrial Control Systems

    Directory of Open Access Journals (Sweden)

    V. Yezhov

    2013-01-01

    Full Text Available We consider the application of embedded microcontrollers and industrial controllers with built-in operating systems.With the development of embedded operating systems and technology of open standard IEC 61131-3 product developer can write their own program management and support staff – to modernize management program.

  6. Risk assessment at workplaces in industrial radiography: from research to action

    Energy Technology Data Exchange (ETDEWEB)

    Coletti, F.; Paul, D.; Sari-Minodier, I.; Botta, A. [Universite de la Mediterranee, Lab. de Biogenotoxicologie et Mutagenese Environnementale (EA 1784 IFR PMSE 112), Faculte de Medecine, 13 - Marseille (France); Mocaer, S.; Sotty, Ph. [Direction Regionale du Travail de l' Emploi et de la Formation Professionnelle, PACA, 13 - Marseille (France); Grolleau, N. [Direction Departementale du Travail de l' Emploi et de la Formation Professionnelle, 13 - Marseille (France); Provens, H.; Landier, D. [Direction de la Surete Nucleaire et de la Radioprotection, div. de Marseille, 13 - Marseille (France); Soler, J.L. [Caisse Regionale d' Assurance Maladie Sud Est, 13 - Marseille (France)

    2006-07-01

    This study focuses on the use of gamma photons usually emitted by a source of iridium 192. Analysis of the working conditions for a radiographer considers first the preparation of the equipment at the home base, then the transport of the gamma projector, considered hazardous under legislation to the site; then the operation itself on the site with, several gamma-graphy shooting per night; and finally to return to base. A table has been produced in order to calculate the doses received during the different stages of the shooting of a a given activity: dose equivalent rate during transport by car: 1.5 {mu} Sv/h, dose equivalent during projector handling: 200 {mu}Sv/h, dose equivalent during collimator handling:15{mu}Sv/h, dose equivalent from change of position between projector and remote control: 10{sup -2}{mu}Sv/shooting, dose equivalent during source ejection: 4{mu}Sv/shooting, dose equivalent during source ejection behind a screen(1 cm of steel): 3{mu}Sv/shooting, dose equivalent at shelter point (behind screen): 5{mu}Sv/h. These calculations indicate that doses(exposure) which are often ignored, such as transport dose or collimator dose, are significant. Thus, working conditions need to be improved with regard to justification, optimization and limitation principles. All the work of the industrial radiographer must be evaluated according to a charter. The charter covers all aspects of operations. It begins with a review of basic radiation protection principles followed by the role and responsibilities of each stakeholder, personal training, medical and dosimetric monitoring of workers. Finally, the step by step procedure is described. (N.C.)

  7. Mexican Official Standard NOM-025/1-NUCL-2000, Requirements for equipment of Industrial radiography. Part 1: General requirements; Norma Oficial Mexicana NOM-025/1-NUCL-2000, Requisitos para equipo de radiografia industrial. Parte 1: Requisitos generales

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-11

    In industrial radiography, devices have been used which allow to use sealed radioactive transmitting sources of gamma radiation the same that it makes to fall on the object to X-ray . With the purpose of that the devices function inside of basic standards of radiological safety during the taking of radiographs, it is necessary that the working container and associated equipment to fulfil with the established in this standard. (Author)

  8. X-ray digital industrial radiography (DIR) for local liquid velocity (VLL) measurement in trickle bed reactors (TBRs): Validation of the technique

    Science.gov (United States)

    Mohd Salleh, Khairul Anuar; Rahman, Mohd Fitri Abdul; Lee, Hyoung Koo; Al Dahhan, Muthanna H.

    2014-06-01

    Local liquid velocity measurements in Trickle Bed Reactors (TBRs) are one of the essential components in its hydrodynamic studies. These measurements are used to effectively determine a reactor's operating condition. This study was conducted to validate a newly developed technique that combines Digital Industrial Radiography (DIR) with Particle Tracking Velocimetry (PTV) to measure the Local Liquid Velocity (VLL) inside TBRs. Three millimeter-sized Expanded Polystyrene (EPS) beads were used as packing material. Three validation procedures were designed to test the newly developed technique. All procedures and statistical approaches provided strong evidence that the technique can be used to measure the VLL within TBRs.

  9. Radiography at CERN

    CERN Document Server

    HSE Unit

    2014-01-01

    What is industrial radiography? It is a non-destructive method with a wide variety of applications, such as inspecting the quality of a weld. It uses high-energy radioactive sources or an X-ray generator.   Is this inspection technique used at CERN? Yes, it is widely used at CERN by the EN-MME Group, which outsources the work to one or more companies, depending on the workload. Is it possible to carry out radiography anywhere at CERN? Yes, it is possible to carry out radiography in any building/accelerator/experiment area at CERN (including in areas which are not normally subject to radiological hazards). When is radiography carried out? It normally takes place outside of working hours (7 p.m. to 6 a.m.). How will I know if radiography is taking place in my building? If this activity is planned in a CERN building, notices will be affixed to all of its main entrance doors at least 24 hours in advance. What are the risks? There is a risk of exposure to very high levels of radiation, dep...

  10. Preliminary results from the application of risk matrix method for safety assessment in industrial radiography; Resultados preliminares de la aplicacion del metodo de matrices de riesgo para evaluaciones de seguridad en radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Lopez G, A.; Cruz, D. [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan 779, Col. Narvarte, 03020 Ciudad de Mexico (Mexico); Truppa, W. [Autoridad Reguladora Nuclear, Buenos Aires (Argentina); Aravena, M. [Comision Chilena de Energia Nuclear, Santiago (Chile); Tamayo, B., E-mail: alopezg@cnsns.gob.mx [Consejo de Seguridad Nuclear, Madrid (Spain)

    2015-09-15

    Although the uses of ionizing radiation in industry are subject to procedures that provide a high level of safety, experience has shown that equipment failure, human errors, or the combination of both that can trigger accidental exposures may occur. Traditionally, the radiation safety checks whether these industrial practices (industrial radiography, industrial irradiators, among others) are sufficiently safe to prevent similar accidental exposures already occurred, so that becomes dependent on the published information and not always answers questions like: What other events can occur, or what other risks are present? Taking into account the results achieved by the Foro Iberoamericano de Organismos Reguladores Radiologicos y Nucleares, its leading position in the use of techniques of risk analysis in radioactive facilities and the need to develop a proactive approach to the prevention of accidents arising from the use of ionizing radiations in the industry, it intends to apply the risk analysis technique known as Risk Matrix to a hypothetical reference entity for the region in which industrial radiography is performed. In this paper the results of the first stage of this study are shown, that is the identification of initiating events (IE) and barriers that help mitigate the consequences of such IE, so that can appreciate the applicability of this method to industrial radiography services, to reduce the risk to acceptable levels. The fundamental advantage associated with the application of this methodology is that can be applied by the professionals working in the service and identifies specific weaknesses that from the point of view of safety there, so they can be prioritized resources depending on risk reduction. (Author)

  11. Assessment of cold neutron radiography capability

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, T.E. Jr.; Roberts, J.A.

    1998-12-31

    This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The authors goals were to demonstrate and assess cold neutron radiography techniques at the Los Alamos Neutron Science Center (LANSCE), Manual Lujan Neutron Scattering Center (Lujan Center), and to investigate potential applications of the capability. The authors have obtained images using film and an amorphous silicon detector. In addition, a new technique they have developed allows neutron radiographs to be made using only a narrow range of neutron energies. Employing this approach and the Bragg cut-off phenomena in certain materials, they have demonstrated material discrimination in radiography. They also demonstrated the imaging of cracks in a sample of a fire-set case that was supplied by Sandia National Laboratory, and they investigated whether the capability could be used to determine the extent of coking in jet engine nozzles. The LANSCE neutron radiography capability appears to have applications in the DOE stockpile maintenance and science-based stockpile stewardship (SBSS) programs, and in industry.

  12. Neutron Radiography

    Science.gov (United States)

    Heller, A. K.; Brenizer, J. S.

    Neutron radiography and its related two-dimensional (2D) neutron imaging techniques have been established as invaluable nondestructive inspection methods and quantitative measurement tools. They have been used in a wide variety of applications ranging from inspection of aircraft engine turbine blades to study of two-phase fluid flow in operating proton exchange membrane fuel cells. Neutron radiography is similar to X-ray radiography in that the method produces a 2D attenuation map of neutron radiation that has penetrated the object being examined. However, the images produced differ and are often complementary due to the differences between X-ray and neutron interaction mechanisms. The uses and types of 2D neutron imaging have expanded over the past 15 years as a result of advances in imaging technology and improvements in neutron generators/sources and computers. Still, high-intensity sources such as those from reactors and spallation neutron sources, together with conventional film radiography, remain the mainstay of high-resolution, large field-of-view neutron imaging. This chapter presents a summary of the history, methods, and related variations of neutron radiography techniques.

  13. Electronic Commerce Resource Centers. An Industry--University Partnership.

    Science.gov (United States)

    Gulledge, Thomas R.; Sommer, Rainer; Tarimcilar, M. Murat

    1999-01-01

    Electronic Commerce Resource Centers focus on transferring emerging technologies to small businesses through university/industry partnerships. Successful implementation hinges on a strategic operating plan, creation of measurable value for customers, investment in customer-targeted training, and measurement of performance outputs. (SK)

  14. Electronic Commerce Resource Centers. An Industry--University Partnership.

    Science.gov (United States)

    Gulledge, Thomas R.; Sommer, Rainer; Tarimcilar, M. Murat

    1999-01-01

    Electronic Commerce Resource Centers focus on transferring emerging technologies to small businesses through university/industry partnerships. Successful implementation hinges on a strategic operating plan, creation of measurable value for customers, investment in customer-targeted training, and measurement of performance outputs. (SK)

  15. Centers for manufacturing technology: Industrial Advisory Committee Review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    An advisory committee, composed of senior managers form industrial- sector companies and major manufacturing trade associations and representatives from appropriate educational institutions, meets semi-annually to review and advise the Oak Ridge Centers for Manufacturing Technology (ORCMT) on its economic security program. Individual papers have been indexed separately for the database.

  16. Final Technical Report for University of Michigan Industrial Assessment Center

    Energy Technology Data Exchange (ETDEWEB)

    Atreya, Arvind

    2007-04-17

    The UM Industrial Assessment Center assisted 119 primary metals, automotive parts, metal casting, chemicals, forest products, agricultural, and glass manufacturers in Michigan, Ohio and Indiana to become more productive and profitable by identifying and recommending specific measures to improve energy efficiency, reduce waste and increase productivity. This directly benefits the environment by saving a total of 309,194 MMBtu of energy resulting in reduction of 0.004 metric tons of carbon emissions. The $4,618,740 implemented cost savings generated also saves jobs that are evaporating from the manufacturing industries in the US. Most importantly, the UM Industrial Assessment Center provided extremely valuable energy education to forty one UM graduate and undergraduate students. The practical experience complements their classroom education. This also has a large multiplier effect because the students take the knowledge and training with them.

  17. Euratom Neutron Radiography Working Group

    DEFF Research Database (Denmark)

    Domanus, Joseph Czeslaw

    1986-01-01

    In 1979 a Neutron Radiography Working Group (NRWG) was constituted within Buratom with the participation of all centers within the European Community at which neutron facilities were available. The main purpose of NRWG was to standardize methods and procedures used in neutron radiography of nuclear...... reactor fuel as well as establish standards for radiographic image quality of neutron radiographs. The NRWG meets once a year in each of the neutron radiography centers to review the progress made and draw plans for the future. Besides, ad-hoc sub-groups or. different topics within the field of neutron...... radiography are constituted. This paper reviews the activities and achievements of the NRWG and its sub-groups....

  18. Radiation protection performance analysis of industrial radiography facilities at Brazil covering the period from 1995 to 1997; Analise do desempenho em radioprotecao das instalacoes de radiografia industrial no Brasil no periodo de 1995 a 1997

    Energy Technology Data Exchange (ETDEWEB)

    Aquino, Josilto Oliveira de; Teixeira, Pedro Barbosa; Souza, Luiz Antonio C. de [Instituto de Radioprotecao e Dosimetria (IRD), Rio de Janeiro, RJ (Brazil)

    1999-11-01

    Accomplishment of analysis of the irregularities verified in the facilities of Industrial Radiography in the period of 1995 until 1995 until 1997, contents the following information: number of facilities, irregularities, classification, occurrence frequency and the number of accomplished inspections. This work discusses some items of radiation protection sets in practice in the period in study, as well as some suggestions that radiation protection could be implemented, with the objective of improving Radioprotection of the facilities and the control accomplished by CNEN. (author) 8 refs., 3 tabs.

  19. Industrial Engineering Lifts Off at Kennedy Space Center

    Science.gov (United States)

    Barth, Tim

    1998-01-01

    When the National Aeronautics and Space Administration (NASA) began the Space Shuttle Program, it did not have an established industrial engineering (IE) capability for several probable reasons. For example, it was easy for some managers to dismiss IE principles as being inapplicable at NASA's John F. Kennedy Space Center (KSC). When NASA was formed by the National Aeronautics and Space Act of 1958, most industrial engineers worked in more traditional factory environments. The primary emphasis early in the shuttle program, and during previous human space flight programs such as Mercury and Apollo, was on technical accomplishments. Industrial engineering is sometimes difficult to explain in NASA's highly technical culture. IE is different in many ways from other engineering disciplines because it is devoted to process management and improvement, rather than product design. Images of clipboards and stopwatches still come to the minds of many people when the term industrial engineering is mentioned. The discipline of IE has only recently begun to gain acceptance and understanding in NASA. From an IE perspective today, the facilities used for flight hardware processing at KSC are NASA's premier factories. The products of these factories are among the most spectacular in the world: safe and successful launches of shuttles and expendable vehicles that carry tremendous payloads into space.

  20. Reconstructive dosimetry and radiation doses evaluation of members of the public due to radiological accident in industrial radiography; Dosimetria reconstrutiva e avaliacao de dose de individuos do publico devido a acidente radiologico em radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Camila Moreira Araujo de

    2016-07-01

    Radiological accidents have occurred mainly in the practices recognized as high risk radiological and classified by the IAEA as Categories 1 and 2, and highlighted the radiotherapy, industrial irradiators and industrial radiography. In Brazil, since there were five major cases in industrial radiography, which involved 7 radiation workers and 19 members of the public, causing localized radiation lesions on the hands and fingers. One of these accidents will be the focus of this work. In this accident, a {sup 192}Ir radioactive source was exposed for more than 8 hours in the workplace inside a company, exposing radiation workers, individuals of the public and people from the surrounding facilities, including children of a school. The radioactive source was also handled by a security worker causing severe radiation injuries in the hand and fingers. In this paper, the most relevant and used techniques of reconstructive dosimetry internationally are presented. To estimate the radiation doses received by exposed individuals in various scenarios of radiological accident in focus, the following computer codes were used: Visual Monte Carlo Dose Calculation (VMC), Virtual Environment for Radiological and Nuclear Accidents Simulation (AVSAR) and RADPRO Calculator. Through these codes some radiation doses were estimated, such as, 33.90 Gy in security worker's finger, 4.47 mSv in children in the school and 55 to 160 mSv for workers in the company during the whole day work. It is intended that this work will contribute to the improvement of dose reconstruction methodology for radiological accidents, having then more realist radiation doses. (author)

  1. The incorporation of User Centered Design and Industrial design

    DEFF Research Database (Denmark)

    Dai, Zheng; Ómarsson, Ólafur

    2011-01-01

    Abstract—Traditional Industrial Design (TID) has been an important aspect in the NPD process within the last decades. User centered design (UCD) is a growing research field for product innovation, starting from the end of 20th century. An NPD process needs support from both design knowledge...... and research methodologies. Both TID and UCD focus on user’s perspective when doing multi-disciplinary work together. They provide skills and methods for designing the style and usability, and balancing the users need and reality. The skills from TID help design expression and realization to communicate...... respectively. Their methodologies are essential for a designer to successfully come to a fruitful design solution, and at the same time the project improves the methodologies of TID and UCD through a reflection process....

  2. Industrial Assessment Centers - Small Manufacturers Reduce Energy & Increase Productivity

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-11-06

    Since 1976, the Industrial Assessment Centers (IACs), administered by the US Department of Energy, have supported small and medium-sized American manufacturers to reduce energy use and increase their productivity and competitiveness. The 24 IACs, located at premier engineering universities around the country (see below), send faculty and engineering students to local small and medium-sized manufacturers to provide no-cost assessments of energy use, process performance and waste and water flows. Under the direction of experienced professors, IAC engineering students analyze the manufacturer’s facilities, energy bills and energy, waste and water systems, including compressed air, motors/pumps, lighting, process heat and steam. The IACs then follow up with written energy-saving and productivity improvement recommendations, with estimates of related costs and payback periods.

  3. Application of the ARCAL XX Project documents for industrial radiography control in Peru; Aplicacion en el Peru de los documentos del Proyecto Arcal XX para el control en radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Medina Gironzini, E. [Instituto Peruano de Energia Nuclear, Lima (Peru). Oficina Tecnica de la Autoridad Nacional

    2001-07-01

    The objectives of the ARCAL XX Project: 'Guidelines on Control of Radiation Sources' (1997-2000) were to elaborate several documents, product of the regional experience that has had great utility for Regulatory Authorities and radiation ionizing users. Some of these documents contain Radiological Safety Requirements, Guide for Authorisation Application and Inspections Procedures. The implementation of these guidelines will improve the effectiveness of regulatory control of radiation sources in Peru by Regulatory Authority (IPEN) and the radiological protection in aspects of occupational, medical, public and potential exposure. This document presents the experience in the development of these guidelines and their contribution for elaborating national regulations for use of industrial radiography.

  4. INTENSITY OF SOIL CONTAMINATION IN INDUSTRIAL CENTERS OF KAZAKHSTAN

    Directory of Open Access Journals (Sweden)

    Amanzhol Iztileu

    2013-06-01

    Full Text Available For Kazakhstan, with its vast territory, the problem of disposal of solid waste from metallurgical, energy and petrochemical industries is becoming more acute. Failure to comply with hygiene requirements for the placement and operation of landfills increases the area of contaminated land and could become a threat to the public of environmental safety of industrial centers. The aim of the study was to evaluate the soil contamination in the towns and cities of Kazakhstan and the allocation of areas of risk to public health. The content of heavy metals in the soil (manganese, zinc, copper, cobalt, nickel, lead, cadmium, mercury, selenium, tin, arsenic, vanadium were determined by atomic absorption spectrometer MGA-915M. Evaluation of the results was performed with respect to the MPC substances in the soil, the toxicity of the components. Summarized metal soil pollution index (IZ was obtained by the sum of the rate of excess metal concentration above the level of its world-Clark. To assess the different risk residence zones scale with 5 levels of purity up to 2 - very clean, 2.8 net, 8-16 acceptable, 16-32 moderately dangerous, dangerous 32-128 was chosen. We developed the original software product using GIS technology to provide environmental information on an electronic map of the city in the form of color patches (polygons, matching levels summarized indicator of soil contamination. Found that the most contaminated soil were village Glubokoe where pollution reached dangerous or extremely dangerous levels, Aktau and Zhanaozen in which moderately hazardous contamination was detected throughout; Ust-Kamenogorsk and village Sholakkorgan where moderately hazardous contamination was noted in the fourth part of the urban area. The most common heavy metal toxicity 1-2 class that exceeded MCL in soils, were lead, copper and zinc, and in village Glubokoe - chromium and arsenic, in Aktau - cadmium. Visualization of environmental pollution in some urban

  5. Creating Communicative Scientists: A Collaboration between a Science Center, College and Science Industry

    Science.gov (United States)

    Wadman, Melissa; Driscoll, Wendy deProphetis; Kurzawa, Elizabeth

    2009-01-01

    Many science centers have partnerships with schools, universities or scientific industry. This article will describe a unique collaborative project between Liberty Science Center, Wagner College, and Picatinny Center (a government research center) that has college interns working with and learning from science center staff and real scientists in a…

  6. 76 FR 1521 - Security Zone: Fleet Industrial Supply Center Pier, San Diego, CA

    Science.gov (United States)

    2011-01-11

    ... SECURITY Coast Guard 33 CFR Part 165 RIN 1625-AA87 Security Zone: Fleet Industrial Supply Center Pier, San... of the San Diego Bay, San Diego, CA. The existing security zone is around the former Fleet Industrial... Fleet Industrial Supply Center Pier. The pier is no longer owned by the U.S. Navy and the security zone...

  7. Dose estimation in the crystalline lens of industrial radiography personnel using Monte Carlo Method; Estimativa de dose nos cristalinos de operadores de gamagrafia industrial usando o metodo de Monte Carlo

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Alexandre Roza de

    2014-07-01

    The International Commission on Radiological Protection, ICRP, in its publication 103, reviewed recent epidemiological evidence and indicated that, for the eye lens, the absorbed dose threshold for induction of late detriment is around 0.5 Gy. On this basis, on April 21, 2011, the ICRP recommended changes to the occupational dose limit in planned exposure situations, reducing the eye lens equivalent dose limit from 150 mSv to 20 mSv per year, on average, during the period of 5 years, with exposure not to exceed 50 mSv in a single year. This paper presents the dose estimation to eye lens, H{sub p}(10), effective dose and doses to important organs in the body, received by industrial gamma radiography workers, during planned or accidental exposure situations. The computer program Visual Monte Carlo was used and two relevant scenarios were postulated. The first is a planned exposure situation scenario where the operator is directly exposed to radiation during the operation. 12 radiographic exposures per day for 250 days per year, which leads to an exposure of 36,000 seconds or 10 hours per year were considered. The simulation was carried out using the following parameters: a {sup 192}Ir source with 1.0 TBq of activity, the source/operator distance varying from 5 m to 10 m at three different heights of 0.2 m, 1.0 m and 2.0 m. The eyes lens doses were estimated as being between 16.9 mSv/year and 66.9 mSv/year and for H{sub p}(10) the doses were between 17.7 mSv/year and 74.2 mSv/year. For the accidental exposure situation scenario, the same radionuclide and activity were used, but in this case the doses were calculated with and without a collimator. The heights above ground considered were 1.0 m, 1.5 m e 2.0 m, the source/operator distance was 40 cm and, the exposure time 74 seconds. The eyes lens doses, for 1.5 m, were 12.3 mGy and 0.28 mGy without and with a collimator, respectively. Three conclusions resulted from this work. The first was that the estimated doses show

  8. Texas A&M University Industrial Assessment Center Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Heffington, Warren M.; Eggebrecht, James A.

    2007-02-24

    This project benefited the public by assisting manufacturing plants in the United States to save costly energy resources and become more profitable. Energy equivalent to over 75,000 barrels of oil was conserved. The Texas A&M University Industrial Assessment Center (IAC) visited 96 manufacturing plants and spent 101 days in those plants during the contract period from August 9, 2002, through November 30, 2006. Recommended annual energy savings for manufacturers were 37,400,000 kWh (127,600 MMBtu—site basis) of electricity and 309,000 MCF (309,000 MMBtu) of natural gas. Each manufacturer subsequently was surveyed, and based on these surveys reportedly implemented 79% of the electricity savings and 36% of the natural gas savings for an overall energy savings of 48% of recommended. Almost 800 (798) projects were recommended to manufacturers, and they accomplished two-thirds of the projects. Cost savings recommended were $12.3 million and implemented savings were $5.7 million or 47%. During the contract period our average time between site visit and report submittal averaged 46 days; and decreased from 48 days in 2003 to 44 days in 2006. Serving clients well and promptly has been a priority. We visited five ESA overflow clients during FY 06. The Texas A&M University IAC pioneered the presentation of air pollution information in reports, and includes NOx and CO2 reductions due to energy savings in all reports. We also experimented with formal PowerPoint BestPractices presentations called Lunchtime/Showtime in each plant and with delivering electronic versions of the report. During the period of the contract, the director served on the Texas Industries of the Future (IOF) Refining and Chemicals Committee, which oversaw the showcases in 2003 and 2006. The assistant director was the Executive Director of the International Energy Technology Conference held annually. The director and assistant director became qualified specialists in the Process Heating Assessment Scoping

  9. International Neutron Radiography Newsletter

    DEFF Research Database (Denmark)

    Domanus, Joseph Czeslaw

    1986-01-01

    At the First World Conference on Neutron Radiography i t was decided to continue the "Neutron Radiography Newsletter", published previously by J.P. Barton, as the "International Neutron Radiography Newsletter" (INRNL), with J.C. Doraanus as editor. The British Journal of Non-Destructive Testing...

  10. Increasing mobile radiography productivity.

    Science.gov (United States)

    Wong, Edward; Lung, Ngan Tsz; Ng, Kris; Jeor, Patrick

    2013-01-01

    Mobile radiography using computed radiography (CR) cassettes is a common equipment combination with a workflow bottleneck limited by location of CR readers. Advent of direct digital radiography (DDR) mobile x-ray machines removes this limitation by immediate image review and quality control. Through the use of key performance indicators (KPIs), the increase in efficiency can be quantified.

  11. Safety protection on industrial radiography detection%工业射线探伤的安全防护

    Institute of Scientific and Technical Information of China (English)

    乐增; 谢宝忠; 江楠

    2012-01-01

    首先介绍射线对机体的伤害,再从安全技术层面介绍了控制区划分、屏蔽物透射量的计算射线安全防护的方法,并且从实际应用出发分别举例说明操作人员允许接受的职业辐射剂量的规定和区域控制及屏蔽物投射量在工程的计算应用;从安全管理层面介绍了对工作人员的要求、安全管理制度及宣传和培训的安全管理的射线防护方法.工业射线防护总的原则是防止射线发生有害的非随机效应、限制随机效应的发生率在被认为是可以接受的水平范围之内,从而尽量降低射线造成的危害.%The radiation damage on the body was introducted, and the control area, the calculation of the amount of shielding, the radiation transmission security methods were introduced on the aspect of security technology, and the examples of operators allowed to accept the provisions of the occupational radiation dose and regional control and shield of the projected amount of computing applications in engineering were given in the practical application, also the safety management system and promotion and training radiation protection safety management methods on the aspects of security management demands on staff. The general principle of industrial radiation protection was to prevent the occurrence of harmful rays of non-random effect, to limit the incidence of random effects considered to be within acceptable levels, thus minimizing radiation hazards.

  12. Radiography With the Patient in the centre

    DEFF Research Database (Denmark)

    Møller, Louise

    2016-01-01

    . Several of these elements have a technical focus. There are relations in an MR scan affecting which actions are included in the scan pathway. However, it is the radiographers who decide which actions to include. Patients and radiographers in this study agreed that center in radiography is about directing......The health care system is becoming more technological, and at the same time, it is verbalized that the patient should be in the center. The purpose of this study was to illucidate how radiography with the patient in the center is performed and what patients and radiographers understand about center...... in radiography. Qualitative methods was used; observations of three MR scans and interviews with three patients and three radiographers are discussed. In the description of an MR scan, it appeared that more elements are involved and that each element has a center of equal importance to complete the MR scan...

  13. 33 CFR 165.1121 - Security Zone: Fleet Supply Center Industrial Pier, San Diego, CA.

    Science.gov (United States)

    2010-07-01

    ... Guard District § 165.1121 Security Zone: Fleet Supply Center Industrial Pier, San Diego, CA. (a... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Security Zone: Fleet Supply Center Industrial Pier, San Diego, CA. 165.1121 Section 165.1121 Navigation and Navigable Waters COAST...

  14. Energy Efficient Industrialized Housing Research Program, Center for Housing Innovation, University of Oregon and the Florida Solar Energy Center

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G.Z.

    1990-01-01

    This research program addresses the need to increase the energy efficiency of industrialized housing. Two research centers have responsibility for the program: the Center for Housing Innovation at the University of Oregon and the Florida Solar Energy Center, a research institute of the University of Central Florida. The two organizations provide complementary architectural, systems engineering, and industrial engineering capabilities. In 1989 we worked on these tasks: (1) the formation of a steering committee, (2) the development of a multiyear research plan, (3) analysis of the US industrialized housing industry, (4) assessment of foreign technology, (5) assessment of industrial applications, (6) analysis of computerized design and evaluation tools, and (7) assessment of energy performance of baseline and advanced industrialized housing concepts. The current research program, under the guidance of a steering committee composed of industry and government representatives, focuses on three interdependent concerns -- (1) energy, (2) industrial process, and (3) housing design. Building homes in a factory offers the opportunity to increase energy efficiency through the use of new materials and processes, and to increase the value of these homes by improving the quality of their construction. Housing design strives to ensure that these technically advanced homes are marketable and will meet the needs of the people who will live in them.

  15. Reference levels for assays in opened installations of industrial radiography; Niveis de referencia para ensaios em instalacoes abertas de radiografia industrial

    Energy Technology Data Exchange (ETDEWEB)

    Leocadio, Joao C.; Tauhata, Luiz [Instituto de Radioprotecao e Dosimetria (IRD), Rio de Janeiro, RJ (Brazil); Crispim, Verginia R. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia Nuclear

    2001-07-01

    This work had as objectives to analyze the facilities open of industrial x-ray to obtain the distribution of doses in the operators and present proposed for the reference levels. The results of the monitoring revealed an improvement of the radiation protection conditions in the facilities and that the risk of potential exposure was reduced. The advantage of the proposed reference levels is that the supervisors would enlarge the frequency of audits in the facilities opened to accomplish the investigations and interventions.The facilities open with 'bunkers' presented distributions with 95% of the doses below 0,2 mSv and the distributions of the facilities with cordoned area they had 75% of the doses below 0,4 mSv. (author)

  16. Non destructive testing of industrial pieces by radiography: quantitative characterization and 3 D reconstruction by the way of a limited number of images; Controle non destructif de pieces industrielles par radiographie: caracterisation quantitative et reconstruction 3D a partir d`un nombre limite de vues

    Energy Technology Data Exchange (ETDEWEB)

    Retraint, F

    1998-12-31

    The non destructive testing of industrial pieces is evaluated on the basis of numerical radiographies.The context of the study is the online control of the fuel rods production. A direct model of a numerical radiography formation is proposed and detailed for an acquisition system consisting of a CCD video connected to a converter screen by an optical system. As this approach does not allow the determination of the measured matter thickness from the X-ray photograph, an approximate model based on realistic approximations of the industrial non destructive testing, has been developed. For the specific cases it is possible to inverse the model and to reach the quantitative information present in the x-ray photograph, in other words, the map of the X-rays measured matter thickness. It becomes then possible to access to the quantitative parameters of the possible defects present in the measured specimen, such as the surface and the bulk. To reach the 3 D information on the defects a 3 D reconstruction method, from 3 X-rays photographs, is proposed.The inverse problem is solved by the non convex energy minimization. (A.L.B.) 109 refs.

  17. R&D Characteristics and Organizational Structure: Case Studies of University-Industry Research Centers

    Science.gov (United States)

    Hart, Maureen McArthur

    2013-01-01

    Within the past few decades, university-industry research centers have been developed in large numbers and emphasized as a valuable policy tool for innovation. Yet little is known about the heterogeneity of organizational structure within these centers, which has implications regarding policy for and management of these centers. This dissertation…

  18. R&D Characteristics and Organizational Structure: Case Studies of University-Industry Research Centers

    Science.gov (United States)

    Hart, Maureen McArthur

    2013-01-01

    Within the past few decades, university-industry research centers have been developed in large numbers and emphasized as a valuable policy tool for innovation. Yet little is known about the heterogeneity of organizational structure within these centers, which has implications regarding policy for and management of these centers. This dissertation…

  19. Collaborative Innovation Research on High-tech Industry in the Center Delta

    Directory of Open Access Journals (Sweden)

    Yan Jingdong

    2017-01-01

    Full Text Available As a strong point in the Middle Rises Strategy, the Center Delta is of great significance to high-tech industry development. While the collaborative innovation is an effective way to promote the coordinated development of regional economy. This article selected electronic and communication equipment manufacturing industry of 3 provinces in the Center Delta as samples, built evaluation index system of collaborative innovation of high-tech industry, and put the relevant data into the system coordination degree model, in order to get the synergy of industrial innovation system and innovation environment system of 3 provinces. The empirical results shown that the industrial innovation system and innovation environment system coordination degree of Hubei province was the highest, while Jiangxi province was the lowest. Based on the empirical result analysis of the above-mentioned systems, this article put forward suggestions to promote the development of the high-tech industry collaborative innovation in the Center Delta.

  20. Anatomy of the Berkeley Sensor & Actuator Center (BSAC): The NSF Industry/University Cooperative Research Center on MEMS

    Science.gov (United States)

    2013-04-08

    a larger research organization than most research  consortia   would be able to maintain.   (4) Maintain collaboration with  Industrial  Members to insure...DATES COVERED 00-00-2013 to 00-00-2013 4. TITLE AND SUBTITLE Anatomy of the Berkeley Sensor & Actuator Center (BSAC): The NSF Industry /University...This has been achieved through creative combinations of resources, incentives and shared goals involving Academia, Industry , and Government. The

  1. Preliminary Study of Indirect Neutron Radiography Method at CARR

    Institute of Scientific and Technical Information of China (English)

    WEI; Guo-hai; HAN; Song-bai; WANG; Hong-li; HE; Lin-feng; WANG; Yu; WU; Mei-mei; LIU; Yun-tao; CHEN; Dong-feng

    2013-01-01

    The Indirect Neutron Radiography is a powerful technique for non-destructively measuring specimens with radioactivity in the nuclear industrial field.China Advanced Research Reactor(CARR)is an excellent platform for Indirect Neutron Radiography and the experimental conditions based on CARR,mainly the first and the second exposure time,have been calculated and analyzed by the Monte Carlo

  2. Digital chest radiography

    DEFF Research Database (Denmark)

    Debess, Jeanne Elisabeth; Vejle-Sørensen, Jens Kristian; Thomsen, Henrik;

    2015-01-01

    of clinical supervisors. Optimal collimation is determined by European and Regional Danish guidelines. The areal between current and optimal collimation is calculated. The experimental research is performed in September - October 2014 Siemens Axiom Aristos digital radiography system DR using 150 kV, 1,25 -3......Purpose: Quality improvement of basic radiography focusing on collimation and dose reduction in digital chest radiography Methods and Materials:A retrospective study of digital chest radiography is performed to evaluate the primary x-ray tube collimation of the PA and lateral radiographs. Data from...... one hundred fifty self-reliant female patients between 15 and 55 years of age are included in the study. The clinical research is performed between September and November 2014 where 3rd year Radiography students collect data on four Danish x-ray departments using identical procedures under guidance...

  3. Digital chest radiography

    DEFF Research Database (Denmark)

    Debess, Jeanne Elisabeth; Johnsen, Karen Kirstine; Thomsen, Henrik

    2015-01-01

    Background: Chest radiography is one of the most common examinations in radiology departments. In 2013 approximately 80,000 chest x-rays were performed on women in the fertile age. Even low dose for the examinationCorrect collimation Purpose: Quality improvement of basic radiography focusing...... collimations depending on side of radiograph. Results from dose reduction will be presented on the congress Conclusion: Correct positioning and collimation of digital chest radiographs can reduce the radiation dose significant to the patients and by that improve the quality of basic radiography....... on collimation and dose reduction in digital chest radiography Methods and Materials A retrospective study of digital chest radiography is performed to evaluate the primary x-ray tube collimation of the PA and lateral radiographs. Data from one hundred fifty self-reliant female patients between 15 and 55 years...

  4. Reliability Centered Maintenance in Schedule Improvement of Automotive Assembly Industry

    Directory of Open Access Journals (Sweden)

    Rizauddin Ramli

    2012-01-01

    Full Text Available Problem statement: Today, in many automotive manufacturing companies, maintenance management is an important factor to maintain the plant operation and production equipments. Approach: In this study, we present an implementation of Reliability Centered Maintenance (RCM practice in one of the automotive manufacturing company in Malaysia. The RCM practice was used to assist the company in focusing their maintenance activities based on the criticalities of the equipments by applying the Failure Modes and Effects Analysis (FMEA. The implementation of RCM was carried out in 4 stages; preparation, system analysis, decision making and feedback. The aim of RCM was to reduce the number of maintenance checklist and to improve significantly the integrity of maintenance practice. Results: As a result, the new RCM framework was generated where Class A equipment was at the top of the monthly maintenance frequency priority, followed by Class B and Class C equipment which had lesser critical value. Conclusion: The new RCM framework is used to conduct visible guideline and propose a new maintenance schedule. The guideline is useful for future maintenance strategy improvement. After the implementation, it can be ascertained that our proposed RCM is useful in reducing maintenance personnel burden and this leads to improvement of productivity.

  5. Exploiting the return on experience of incidents in the field of industrial radiography; L'exploitation du retour d'experience des incidents dans le domaine de la radiographie industrielle

    Energy Technology Data Exchange (ETDEWEB)

    Bataille, C.; Crouail, P. [Centre d' Etude sur I' Evaluation de la Protection dans le domaine Nucleaire (CEPN), 28 rue de la Redoute, 92260 Fontenay-aux-Roses (France); Gauron, C. [Institut National de Recherche et de Securite (INRS), 30 rue Olivier Noyer, 75014 Paris (France); Abela, G. [EDF, DIN DQSNR, 1 Place Pleyel, 93282 St Denis Cedex (France); Martin, E. [COFREND, 1 rue Gaston Boissier, 75724 PARIS Cedex 15 (France)

    2008-07-01

    After a presentation of the RELIR network (a French system of return on experience on radiological incidents), the aim of which is to collect typical incidents in different activity sectors (industry, medicine, veterinary, research, teaching, transports) in order to report them during professional training sessions, the authors briefly present some new files which have been recently produced. They deal with incidents due to a failing marking-out, intentional marking overstepping during non destructive testing, incomplete evacuation of the exclusion zone during non destructive testing and irradiation of an operator during a gamma-graphic shot, incident during a training session

  6. Combining total energy and energy industrial center concepts to increase utilization efficiency of geothermal energy

    Science.gov (United States)

    Bayliss, B. P.

    1974-01-01

    Integrating energy production and energy consumption to produce a total energy system within an energy industrial center which would result in more power production from a given energy source and less pollution of the environment is discussed. Strong governmental support would be required for the crash drilling program necessary to implement these concepts. Cooperation among the federal agencies, power producers, and private industry would be essential in avoiding redundant and fruitless projects, and in exploiting most efficiently our geothermal resources.

  7. The importance of Sumgait industrial center in economic development of Azerbaijan in the context of innovative economics

    Directory of Open Access Journals (Sweden)

    Shafa Aliyev

    2009-10-01

    Full Text Available The paper discusses production capacity of Sumgait industrial center in Azerbaijan. The author observes priority policy directions to utilize available production capacity of this regional industrial complex.

  8. [Shifting path of industrial pollution gravity centers and its driving mechanism in Pan-Yangtze River Delta].

    Science.gov (United States)

    Zhao, Hai-Xia; Jiang, Xiao-Wei; Cui, Jian-Xin

    2014-11-01

    Shifting path of industrial pollution gravity centers is the response of environmental special formation during the industry transfer process, in order to prove the responding of industrial pollution gravity centers to industry transfer in economically developed areas, this paper calculates the gravity centers of industrial wastewater, gas and solid patterns and reveals the shifting path and its driving mechanism, using the data of industrial pollution in the Pan-Yangtze River Delta from 2000 to 2010. The results show that the gravity center of the industrial waste in Pan-Yangtze River Delta shifts for sure in the last 10 years, and gravity center of solid waste shifts the maximum distance within the three wastes, which was 180.18 km, and shifting distances for waste gas and waste water were 109.51 km and 85.92 km respectively. Moreover, the gravity center of the industrial waste in Pan-Yangtze River Delta shifts westwards, and gravity centers of waste water, gas and solid shift for 0.40 degrees, 0.17 degrees and 0.03 degrees respectively. The shifting of industrial pollution gravity centers is driven by many factors. The rapid development of the heavy industry in Anhui and Jiangxi provinces results in the westward shifting of the pollutions. The optimization and adjustment of industrial structures in Yangtze River Delta region benefit to alleviating industrial pollution, and high-polluting industries shifted to Anhui and Jiangxi provinces promotes pollution gravity center shifting to west. While the development of massive clean enterprise, strong environmental management efforts and better environmental monitoring system slow the shifting trend of industrial pollution to the east in Yangtze River Delta. The study of industrial pollution gravity shift and its driving mechanism provides a new angle of view to analyze the relationship between economic development and environmental pollution, and also provides academic basis for synthetical management and control of

  9. Fighting Obsolescence in the Nuclear Power Industry. Motor Control Centers-solutions and Case Study

    Energy Technology Data Exchange (ETDEWEB)

    Portillo, J.; Torralba Piqueras, A.

    2014-07-01

    Motor Control Centers (MCCs) are vital to the operation and control of nuclear power plants. A significant and growing problem within the global nuclear industry is the aging of MCC components. Obsolescence of various components within the MCCs such as molded case circuit breakers, starters, relays, heaters, transformers, etc., are impacting the reliability of MCCs to perform their intended safety function. (Author)

  10. Preparing Teachers for Place-Based Instruction at the Tsongas Industrial History Center

    Science.gov (United States)

    Greenwood, Anita; Kirschbaum, Sheila

    2014-01-01

    In spite of the economic climate which has led to financial retrenchment in school districts, the Tsongas Industrial History Center (TIHC) in Lowell, Massachusetts, which was formed through a collaboration between the National Park Service Lowell National Historical Park and the University of Massachusetts Lowell Graduate School of Education,…

  11. A Method for User Centering Systematic Product Development Aimed at Industrial Design Students

    Science.gov (United States)

    Coelho, Denis A.

    2010-01-01

    Instead of limiting the introduction and stimulus for new concept creation to lists of specifications, industrial design students seem to prefer to be encouraged by ideas in context. A new method that specifically tackles human activity to foster the creation of user centered concepts of new products was developed and is presented in this article.…

  12. Briefing Paper regarding the Establishment of a Regional Technical and Industrial Skills Training Center.

    Science.gov (United States)

    Powell, Roger Baden

    In spring 1997, Oregon's Regional Workforce Committee commissioned a study to investigate the feasibility of creating a technical and industrial skills training center in Region 12 of the state. Interviews were conducted with 40 individuals from area companies, social service agencies, and training organizations regarding the need for such a…

  13. Linguistic Globalization and the Call Center Industry: Imperialism, Hegemony or Cosmopolitanism?

    Science.gov (United States)

    Sonntag, Selma K.

    2009-01-01

    Linguistic imperialism, linguistic hegemony and linguistic cosmopolitanism are broad and contrasting conceptualizations of linguistic globalization that are frequently, if implicitly, invoked in the literature, both academic and non-academic, on language practices and perceptions in the call center industry. I begin with outlining each of these…

  14. Center for Semiconductor Materials and Device Modeling: expanding collaborative research opportunities between government, academia, and industry

    Science.gov (United States)

    Perconti, Philip; Bedair, Sarah S.; Bajaj, Jagmohan; Schuster, Jonathan; Reed, Meredith

    2016-09-01

    To increase Soldier readiness and enhance situational understanding in ever-changing and complex environments, there is a need for rapid development and deployment of Army technologies utilizing sensors, photonics, and electronics. Fundamental aspects of these technologies include the research and development of semiconductor materials and devices which are ubiquitous in numerous applications. Since many Army technologies are considered niche, there is a lack of significant industry investment in the fundamental research and understanding of semiconductor technologies relevant to the Army. To address this issue, the US Army Research Laboratory is establishing a Center for Semiconductor Materials and Device Modeling and seeks to leverage expertise and resources across academia, government and industry. Several key research areas—highlighted and addressed in this paper—have been identified by ARL and external partners and will be pursued in a collaborative fashion by this Center. This paper will also address the mechanisms by which the Center is being established and will operate.

  15. Bone X-Ray (Radiography)

    Medline Plus

    Full Text Available ... the limitations of Bone X-ray (Radiography)? What is Bone X-ray (Radiography)? An x-ray (radiograph) ... diagnosis and disease management. top of page How is the procedure performed? The technologist, an individual specially ...

  16. Real-time radiography

    Energy Technology Data Exchange (ETDEWEB)

    Bossi, R.H.; Oien, C.T.

    1981-02-26

    Real-time radiography is used for imaging both dynamic events and static objects. Fluorescent screens play an important role in converting radiation to light, which is then observed directly or intensified and detected. The radiographic parameters for real-time radiography are similar to conventional film radiography with special emphasis on statistics and magnification. Direct-viewing fluoroscopy uses the human eye as a detector of fluorescent screen light or the light from an intensifier. Remote-viewing systems replace the human observer with a television camera. The remote-viewing systems have many advantages over the direct-viewing conditions such as safety, image enhancement, and the capability to produce permanent records. This report reviews real-time imaging system parameters and components.

  17. 平板DR数字成像技术在焊管行业中的应用%Application of Flat Panel Digital Radiography Imaging Technology in Welded Pipe Industry

    Institute of Scientific and Technical Information of China (English)

    王长安; 余国民; 魏雅博

    2014-01-01

    In this article, it introduced the working principle of digital radiography(DR) imaging technology and its application in welded pipe industry. Compared with the detection effect of traditional X-ray industrial TV from sensitivity detection, image resolution, residual magnetization, radiation dose etc. The result showed that the flat panel DR imaging technology is with some advantages, such as high sensitivity of detection, high efficiency, low labour tension, little doses of radiation and so on. It ensures the weld quality, greatly reduces the accident rate of pipeline, and can replace X-ray industrial TV detecting technology. At present, this technology is widely applied in welded pipe industry.%介绍了DR数字成像技术的工作原理及其在焊管行业检测中的应用。在灵敏度检测、图像分辨率、剩磁影响和辐射剂量等方面与传统的X射线工业电视的检测效果进行了比较分析。结果表明, DR数字成像技术具有检测灵敏度和检测效率较高、劳动强度小、辐射剂量小等优点,保证了焊缝质量,大大降低了管线的事故发生率,可以替代传统X射线工业电视检测技术在焊管行业的应用。

  18. Bone X-Ray (Radiography)

    Medline Plus

    Full Text Available ... Resources Professions Site Index A-Z X-ray (Radiography) - Bone Bone x-ray uses a very small ... X-ray (Radiography)? What is Bone X-ray (Radiography)? An x-ray (radiograph) is a noninvasive medical ...

  19. Artifacts in digital radiography

    Energy Technology Data Exchange (ETDEWEB)

    Min, Jung Whan [Dept. of Radiological Technology, Shin Gu University, Sungnam (Korea, Republic of); Kim, Jung Min [Dept. of Radiological Technology, Korea University, Seoul (Korea, Republic of); Jeong, Hoi Woun [Dept. of Radiological Technology, Beakseok Culture University, Cheonan (Korea, Republic of)

    2015-12-15

    Digital Radiography is a big part of diagnostic radiology. Because uncorrected digital radiography image supported false effect of Patient’s health care. We must be manage the correct digital radiography image. Thus, the artifact images can have effect to make a wrong diagnosis. We report types of occurrence by analyzing the artifacts that occurs in digital radiography system. We had collected the artifacts occurred in digital radiography system of general hospital from 2007 to 2014. The collected data had analyzed and then had categorize as the occurred causes. The artifacts could be categorized by hardware artifacts, software artifacts, operating errors, system artifacts, and others. Hardware artifact from a Ghost artifact that is caused by lag effect occurred most frequently. The others cases are the artifacts caused by RF noise and foreign body in equipments. Software artifacts are many different types of reasons. The uncorrected processing artifacts and the image processing error artifacts occurred most frequently. Exposure data recognize (EDR) error artifacts, the processing error of commissural line, and etc., the software artifacts were caused by various reasons. Operating artifacts were caused when the user did not have the full understanding of the digital medical image system. System artifacts had appeared the error due to DICOM header information and the compression algorithm. The obvious artifacts should be re-examined, and it could result in increasing the exposure dose of the patient. The unclear artifact leads to a wrong diagnosis and added examination. The ability to correctly determine artifact are required. We have to reduce the artifact occurrences by understanding its characteristic and providing sustainable education as well as the maintenance of the equipments.

  20. Analysis of public perception about impaired odor in center fishery processing industry Tegalsari Tegal city

    Science.gov (United States)

    Wibowo, Tri Setyo; Purwanto, P.; Yulianto, Bambang

    2017-03-01

    The Coastal Fishing Port (CFP) Tegalsari is one of the largest center of the fishery industries in Central Java Indonesia. In addition to producing fish-based products such as fish fillets, salted fish and fish meal are distributed to most major cities in Indonesia, but also generate waste and wastewater which potentially disrupt the environment. The purpose of this study describe the perception of the public about the negative impact of the activities in center fishery processing industry. The research method uses qualitative research design with the population living around the center of the fishing industry, with samples taken by purposive sampling numbered 30 people and 3 location sample to know concentration of ammoniac and hydrogen Sulfide. Data research in 2016 was processed using statistical methods. The results of research showed very significant, 80% of respondents who said the fishing activities causing nuisance odor. The remaining 20% stated that the odor nuisance almost imperceptibly. The nuisance of odor are perceived by 53% of respondents for a full day. There are 70% of respondents living around the center of the fishing industry who lived more than seven years, and the remaining 30% of respondents who lived less than 7 years. Conclusion respondent who live more than seven years and said there was no odor nuisance around 57%, are more than 50% of the respondents. The odor of the most influential parameter on the fishing industry is an element of ammoniac (NH3) instead of Hydrogen Sulfide (H2S), because the value at these three locations for Hydrogen Sulfide measurement results show the same number that is equal to 0.001 g/m3. While ammoniac levels at most locations smelled according to perceptions of examiners showed the highest scores, while the zone that did not feel the smell indicates a low value, the test results showed a clear level of distinction. So the need to manage the environment at the center of the fishing industry with a approach of

  1. First optical education center in Japan established by cooperation between academia and industry

    Science.gov (United States)

    Yatagai, Toyohiko

    2014-07-01

    At the present of the 21st century, optical technology became what must be in our life. If there is no optical technology, we cannot use optical equipments such as the camera, microscopes, DVD, LEDs and laser diodes (LDs). Optics is also the leading part in the most advanced scientific field. It is clear that the organization which does education and research is required in such a very important area. Unfortunately, there was no such organization in Japan. The education and research of light have been individually done in various faculties of universities, various research institutes, and many companies. However, our country is now placed in severer surroundings, such as the globalization of our living, the accelerated competition in research and development. This is one of the reasons why Utsunomiya University has established Center for Optical Research and Education (CORE) in 2007. To contribute to optical technology and further development of optical industry, "Center for Optical Research and Education (CORE), Utsunomiya University" promotes education and research in the field of the optical science and technology cooperatively with industry, academia and the government. Currently, 6 full professors, 21 cooperative professors, 2 visiting professors and 7 post-doctoral researchers and about 40 students are joined with CORE. Many research projects with industries, the local government of Tochigi as well as Japanese government. Optical Innovation Center has established in CORE by supporting of Japan Science and Technology Agency in 2011 to develop advanced optical technologies for local companies.

  2. Adaptation of a Control Center Development Environment for Industrial Process Control

    Science.gov (United States)

    Killough, Ronnie L.; Malik, James M.

    1994-01-01

    In the control center, raw telemetry data is received for storage, display, and analysis. This raw data must be combined and manipulated in various ways by mathematical computations to facilitate analysis, provide diversified fault detection mechanisms, and enhance display readability. A development tool called the Graphical Computation Builder (GCB) has been implemented which provides flight controllers with the capability to implement computations for use in the control center. The GCB provides a language that contains both general programming constructs and language elements specifically tailored for the control center environment. The GCB concept allows staff who are not skilled in computer programming to author and maintain computer programs. The GCB user is isolated from the details of external subsystem interfaces and has access to high-level functions such as matrix operators, trigonometric functions, and unit conversion macros. The GCB provides a high level of feedback during computation development that improves upon the often cryptic errors produced by computer language compilers. An equivalent need can be identified in the industrial data acquisition and process control domain: that of an integrated graphical development tool tailored to the application to hide the operating system, computer language, and data acquisition interface details. The GCB features a modular design which makes it suitable for technology transfer without significant rework. Control center-specific language elements can be replaced by elements specific to industrial process control.

  3. Quantitative film radiography

    Energy Technology Data Exchange (ETDEWEB)

    Devine, G.; Dobie, D.; Fugina, J.; Hernandez, J.; Logan, C.; Mohr, P.; Moss, R.; Schumacher, B.; Updike, E.; Weirup, D.

    1991-02-26

    We have developed a system of quantitative radiography in order to produce quantitative images displaying homogeneity of parts. The materials that we characterize are synthetic composites and may contain important subtle density variations not discernible by examining a raw film x-radiograph. In order to quantitatively interpret film radiographs, it is necessary to digitize, interpret, and display the images. Our integrated system of quantitative radiography displays accurate, high-resolution pseudo-color images in units of density. We characterize approximately 10,000 parts per year in hundreds of different configurations and compositions with this system. This report discusses: the method; film processor monitoring and control; verifying film and processor performance; and correction of scatter effects.

  4. CCD digital radiography system

    Science.gov (United States)

    Wang, Yi; Kang, Xi; Li, Yuanjing; Cheng, Jianping; Hou, Yafei; Han, Haiwei

    2009-07-01

    Amorphous silicon flat-panel detector is the mainstream used in digital radiography (DR) system. In latest years, scintillation screen coupled with CCD DR is becoming more popular in hospital. Compared with traditional amorphous silicon DR, CCD-DR has better spatial resolution and has little radiation damage. It is inexpensive and can be operated easily. In this paper, A kind of CCD based DR system is developed. We describe the construction of the system, the system performances and experiment results.

  5. Lessons Learned Through the Follow-up of the Long-Term Effects of Over-Exposure to an Ir192 Industrial Radiography Source in Bangladesh

    Energy Technology Data Exchange (ETDEWEB)

    Jalil, A.; Rabbani, G.; Hossain, M. K.; Alam, M. K.; Koddus, A.

    2003-02-24

    An industrial radiographer was accidentally over-exposed while taking the radiograph of weld-joints of gas pipe-lines in 1985 in Bangladesh. Symptoms of high radiation exposure occurred immediately after the accident and skin erythema developed leading to progressive tissue deterioration. The consequences of this over-exposure is being followed up to assess the long-term effects of ionizing radiation on the victim. Progressive tissue deteriorations have already led to multiple surgeries and successive amputations of the finger-tips so far. Lessons learned from this accident are also reported in this paper.

  6. Electronic imaging system for neutron radiography at a low power research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, F.J.O., E-mail: fferreira@ien.gov.b [Instituto de Engenharia Nuclear, Comissao Nacional de Energia Nuclear, Caixa Postal 68550, CEP 21945-970, Rio de Janeiro (Brazil); Silva, A.X.; Crispim, V.R. [PEN/COPPE-DNC/POLI CT, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970 Rio de Janeiro (Brazil)

    2010-08-15

    This paper describes an electronic imaging system for producing real time neutron radiography from a low power research reactor, which will allow inspections of samples with high efficiency, in terms of measuring time and result analysis. This system has been implanted because of its potential use in various scientific and industrial areas where neutron radiography with photographic film could not be applied. This real time system is installed in neutron radiography facility of Argonauta nuclear research reactor, at the Instituto de Engenharia Nuclear of the Comissao Nacional de Energia Nuclear, in Brazil. It is adequate to perform real time neutron radiography of static and dynamic events of samples.

  7. A WEB-BASED FRAMEWORK FOR VISUALIZING INDUSTRIAL SPATIOTEMPORAL DISTRIBUTION USING STANDARD DEVIATIONAL ELLIPSE AND SHIFTING ROUTES OF GRAVITY CENTERS

    National Research Council Canada - National Science Library

    Y. Song; Z. Gui; H. Wu; Y. Wei

    2017-01-01

    .... The framework uses standard deviational ellipse (SDE) and shifting route of gravity centers to show the spatial distribution and yearly developing trends of different enterprise types according to their industry categories...

  8. Acetabulum protrusio and center edge angle: new MR-imaging measurement criteria - a correlative study with measurement derived from conventional radiography

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Lina; Resnick, Donald [VASDHS-Radiology, San Diego, CA (United States); UCSD Medical Center, San Diego, CA (United States); Boonthathip, Mayura; Cardoso, Fabiano; Clopton, Paul [VASDHS-Radiology, San Diego, CA (United States)

    2009-02-15

    The goal of this study was to identify a method of measurement for acetabulum protrusio and center edge angle (CEA) using MR imaging of the pelvis that correlated with classic methods using radiographic landmarks. MR images and radiographs of the pelvis in 67 patients (132 hips) were used to identify reliable MR-imaging methods for measuring protrusio acetabulum and CEA that correlated strongly with established radiographic measurements. Protrusio acetabulum was determined using the radiographic criterion that the acetabular line projects medial to the ilioischial line by 3 mm or more in men and 6 mm or more in women. Pearson correlation factor was used to determine inter-observer variability and those methods that demonstrated the strongest correlation. The mean and standard deviation of MR-imaging and radiographic measurements for both the normal and protrusio hips were established. Several MR methods correlated strongly with radiographic measurements. The preferred method employed axial MR images at the level of the ischial spine with measurement of the distance between the medial most point of the acetabular fossa and a line perpendicular to the horizontal axis that passed through the lateral margin of the posterior inner pelvic wall. The Pearson's correlation factor between radiographic and MR measurements using this method was 0.84, and inter-observer correlation was 0.80. There were 126 hips in 63 patients (17 female and 44 male) that did not meet the radiographic criteria for protrusio acetabula. In this group of normal hips, the mean and standard deviation of radiographic measurements were 1.9 and 2.8 mm in male patients and -0.5 and 1.7 mm in female patients, and the mean and standard deviation for the preferred MR method was 1.3 and 2.5 mm in male patients and -0.8 and 1.9 mm in female patients. A total of six hips in four patients (two female and two male) met the radiographic criteria for protrusio acetabula. In this group of patients, the mean

  9. Radiography with polarised neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, Michael L.

    2010-08-20

    In this thesis I present a new technique for the spatially resolved investigation of the magnetic properties of bulk samples. Standard one dimensional neutron depolarisation analysis is combined with neutron radiography to a method we call Neutron Depolarisation Imaging (NDI). The experimental setup which was installed at the neutron radiography beam line ANTARES at FRM II consists of a double crystal monochromator, neutron polariser, spin flipper, polarisation analyser and a position sensitive CCD detector. A comprehensive discussion of the requirements for these components is given and the limitations of the method are shown. The maximum spatial resolution which can be achieved with a neutron radiography setup is determined by the collimation of the neutron beam and the distance between sample and detector. Different types of polarisers have been tested and their advantages and disadvantages are discussed. A double crystal monochromator and a new type of polariser employing polarising neutron supermirrors based on the principle of an optical periscope were developed and tested during this work. Furthermore, NDI measurements on various samples of the weakly ferromagnetic materials Pd{sub 1-x}Ni{sub x} and Ni{sub 3}Al are presented. Neutron depolarisation radiography and tomography measurements were conducted with a spatial resolution as high as 0.3 mm on Pd{sub 1-x}Ni{sub x} and Ni{sub 3}Al samples. The feasibility of NDI experiments under hydrostatic pressures up to 10 kbar was shown on a sample of Ni{sub 3}Al using a modified Cu:Be clamp cell. A decrease of the ordering temperature by 2 K under hydrostatic pressure was determined from the NDI measurements and shows the potential of the method for further high pressure experiments. Additionally a method was developed which in principle allows to obtain the intrinsic dependence of the ordering temperature T{sub C} on the ordered moment Ms from NDI measurements on inhomogeneous samples containing regions with

  10. 77 FR 72869 - Guidance for Industry on Limiting the Use of Certain Phthalates as Excipients in Center for Drug...

    Science.gov (United States)

    2012-12-06

    ... flexibility, but they also may be used for different functions in other dosage forms. Phthalates also are... Excipients in CDER-Regulated Products.'' This guidance provides the pharmaceutical industry with the Center... guidance recommends that the pharmaceutical industry avoid the use of these two specific phthalates...

  11. Defense, basic, and industrial research at the Los Alamos Neutron Science Center: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Longshore, A.; Salgado, K. [comps.

    1995-10-01

    The Workshop on Defense, Basic, and Industrial Research at the Los Alamos Neutron Science Center gathered scientists from Department of Energy national laboratories, other federal institutions, universities, and industry to discuss the use of neutrons in science-based stockpile stewardship, The workshop began with presentations by government officials, senior representatives from the three weapons laboratories, and scientific opinion leaders. Workshop participants then met in breakout sessions on the following topics: materials science and engineering; polymers, complex fluids, and biomaterials; fundamental neutron physics; applied nuclear physics; condensed matter physics and chemistry; and nuclear weapons research. They concluded that neutrons can play an essential role in science-based stockpile stewardship and that there is overlap and synergy between defense and other uses of neutrons in basic, applied, and industrial research from which defense and civilian research can benefit. This proceedings is a collection of talks and papers from the plenary, technical, and breakout session presentations. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

  12. Threats to the Sustainability of the Outsourced Call Center Industry in the Philippines: Implications for Language Policy

    Science.gov (United States)

    Friginal, Eric

    2009-01-01

    This study overviews current threats to the sustainability of the outsourced call center industry in the Philippines and discusses implications for macro and micro language policies given the use of English in this cross-cultural interactional context. This study also summarizes the present state of outsourced call centers in the Philippines, and…

  13. Scatter in cargo radiography.

    Science.gov (United States)

    Miller, Erin A; Caggiano, Joseph A; Runkle, Robert C; White, Timothy A; Bevill, Aaron M

    2011-03-01

    As a complement to passive detection systems, radiographic inspection of cargo is an increasingly important tool for homeland security because it has the potential to detect highly attenuating objects associated with special nuclear material or surrounding shielding, in addition to screening for items such as drugs or contraband. Radiographic detection of such threat objects relies on high image contrast between regions of different density and atomic number (Z). Threat detection is affected by scatter of the interrogating beam in the cargo, the radiographic system itself, and the surrounding environment, which degrades image contrast. Here, we estimate the extent to which scatter plays a role in radiographic imaging of cargo containers. Stochastic transport simulations were performed to determine the details of the radiography equipment and surrounding environment, which are important in reproducing measured data and to investigate scatter magnitudes for typical cargo. We find that scatter plays a stronger role in cargo radiography than in typical medical imaging scenarios, even for low-density cargo, with scatter-to-primary ratios ranging from 0.14 for very low density cargo, to between 0.20 and 0.40 for typical cargo, and higher yet for dense cargo.

  14. Revisited the mathematical derivation wall thickness measurement of pipe for radiography

    Energy Technology Data Exchange (ETDEWEB)

    Hamzah, A.R.; Amir, S.M.M. [Non Destructive Testing(NDT) Group, Industrial Technology Div., Malaysian Nuclear Agency, Selangor (Malaysia)

    2007-07-01

    Wall thickness measurement of pipe is very important of the structural integrity of the industrial plant. However, the radiography method has an advantage because the ability of penetrating the insulated pipe. This will have economic benefit for industry. Moreover, the era of digital radiography has more advantages because the speed of radiographic work, less exposure time and no chemical used for film development. Either the conventional radiography or digital radiology, the wall thickness measurement is using the tangential radiography technique (TRT). In case, of a large diameter, pipe (more than inches) the determination maximum penetration wall thickness must be taken into the consideration. This paper is revisited the mathematical derivation of the determination of wall thickness measurement based on tangential radiography technique (TRT). The mathematical approach used in this derivation is the Pythagoras theorem and geometrical principles. In order to derive the maximum penetration wall thickness a similar approach is used. (authors)

  15. Comparison of ultrasonography and radiography in diagnosis of rib fractures.

    Science.gov (United States)

    Pishbin, Elham; Ahmadi, Koorosh; Foogardi, Molood; Salehi, Maryam; Seilanian Toosi, Farrokh; Rahimi-Movaghar, Vafa

    2017-08-01

    Rib fractures are the most common skeletal thoracic injuries resulting from blunt chest trauma. Half of the rib fractures are not detected upon a precise physical evaluation and radiographs. Recently ultrasonography (USG) has been investigated to detect rib fractures. But based on literature the usefulness of USG varies widely. This study was conducted to investigate the role of USG in the detection of possible rib fractures in comparison with radiography. In this cross-sectional study, consecutive patients with minor blunt chest trauma and suspected rib fractures presenting in Imam Reza Hospital located in Mashhad-Iran, between April 2013 and October 2013 were assessed by USG and radiography. The radiography was performed in a posteroanterior (PA) chest projection and oblique rib view centered over the area of trauma. The time duration spent in taking USG and radiography were recorded. The prevalence and location of fractures revealed by USG and radiography were compared. Sixty-one suspected patients were assessed. The male to female ratio was 2.4:1 (43 men and 18 women) with a mean ± SD age of (44.3 ± 19.7) years. There were totally 59 rib fractures in 38 (62.3%) patients based on radiography and USG, while 23 (37.7%) patients had no diagnostic evidence of rib lesions. USG revealed 58 rib fractures in 33 (54.1%) of 61 suspected patients and radiographs revealed 32 rib fractures in 20 (32.8%) of 61 patients. A total of 58 (98.3%) rib fractures were detected by USG, whereas oblique rib view and PA chest radiography showed 27 (45.8%) and 24 (40.7%) rib fractures, respectively. The average duration of USG was (12 ± 3) min (range 7-17 min), whereas the duration of radiography was (27 ± 6) min (range 15-37 min). The kappa coefficient showed a low level of agreement between both USG and PA chest radiography (kappa coefficient = 0.28), and between USG and oblique rib view (kappa coefficient = 0.32). USG discloses more fractures than radiography in

  16. Selection of melter systems for the DOE/Industrial Center for Waste Vitrification Research

    Energy Technology Data Exchange (ETDEWEB)

    Bickford, D.F.

    1993-12-31

    The EPA has designated vitrification as the best developed available technology for immobilization of High-Level Nuclear Waste. In a recent federal facilities compliance agreement between the EPA, the State of Washington, and the DOE, the DOE agreed to vitrify all of the Low Level Radioactive Waste resulting from processing of High Level Radioactive Waste stored at the Hanford Site. This is expected to result in the requirement of 100 ton per day Low Level Radioactive Waste melters. Thus, there is increased need for the rapid adaptation of commercial melter equipment to DOE`s needs. DOE has needed a facility where commercial pilot scale equipment could be operated on surrogate (non-radioactive) simulations of typical DOE waste streams. The DOE/Industry Center for Vitrification Research (Center) was established in 1992 at the Clemson University Department of Environmental Systems Engineering, Clemson, SC, to address that need. This report discusses some of the characteristics of the melter types selected for installation of the Center. An overall objective of the Center has been to provide the broadest possible treatment capability with the minimum number of melter units. Thus, units have been sought which have broad potential application, and which had construction characteristics which would allow their adaptation to various waste compositions, and various operating conditions, including extreme variations in throughput, and widely differing radiological control requirements. The report discusses waste types suitable for vitrification; technical requirements for the application of vitrification to low level mixed wastes; available melters and systems; and selection of melter systems. An annotated bibliography is included.

  17. Mobile real time radiography system

    Energy Technology Data Exchange (ETDEWEB)

    Vigil, J.; Taggart, D.; Betts, S. [Los Alamos National Lab., NM (United States)] [and others

    1997-11-01

    A 450-keV Mobile Real Time Radiography (RTR) System was delivered to Los Alamos National Laboratory (LANL) in January 1996. It was purchased to inspect containers of radioactive waste produced at (LANL). Since its delivery it has been used to radiograph more than 600 drums of radioactive waste at various LANL sites. It has the capability of inspecting waste containers of various sizes from <1-gal. buckets up to standard waste boxes (SWB, dimensions 54.5 in. x 71 in. x 37 in.). It has three independent x-ray acquisition formats. The primary system used is a 12- in. image intensifier, the second is a 36-in. linear diode array (LDA) and the last is an open system. It is fully self contained with on board generator, HVAC, and a fire suppression system. It is on a 53-ft long x 8-ft. wide x 14-ft. high trailer that can be moved over any highway requiring only an easily obtainable overweight permit because it weights {approximately}38 tons. It was built to conform to industry standards for a cabinet system which does not require an exclusion zone. The fact that this unit is mobile has allowed us to operate where the waste is stored, rather than having to move the waste to a fixed facility.

  18. Axial Tomography from Digitized Real Time Radiography

    Science.gov (United States)

    Zolnay, A. S.; McDonald, W. M.; Doupont, P. A.; McKinney, R. L.; Lee, M. M.

    1985-01-18

    Axial tomography from digitized real time radiographs provides a useful tool for industrial radiography and tomography. The components of this system are: x-ray source, image intensifier, video camera, video line extractor and digitizer, data storage and reconstruction computers. With this system it is possible to view a two dimensional x-ray image in real time at each angle of rotation and select the tomography plane of interest by choosing which video line to digitize. The digitization of a video line requires less than a second making data acquisition relatively short. Further improvements on this system are planned and initial results are reported.

  19. Migration and Health in the Construction Industry: Culturally Centering Voices of Bangladeshi Workers in Singapore

    Science.gov (United States)

    Dutta, Mohan J.

    2017-01-01

    Construction workers globally face disproportionate threats to health and wellbeing, constituted by the nature of the work they perform. The workplace fatalities and lost-time injuries experienced by construction workers are significantly greater than in other forms of work. This paper draws on the culture-centered approach (CCA) to dialogically articulate meanings of workplace risks and injuries, voiced by Bangladeshi migrant construction workers in Singapore. The narratives voiced by the participants suggest an ecological approach to workplace injuries in the construction industries, attending to food insecurity, lack of sleep, transportation, etc. as contextual features of work that shape the risks experienced at work. Moreover, participant voices point to the barriers in communication, lack of understanding, and experiences of incivility as features of work that constitute the ways in which they experience injury risks. The overarching discourses of productivity and efficiency constitute a broader climate of threats to worker safety and health. PMID:28146056

  20. Proton radiography for clinical applications

    Energy Technology Data Exchange (ETDEWEB)

    Talamonti, C., E-mail: cinzia.talamonti@unifi.i [Dipartimento di Fisiopatologia Clinica, Universita degli Studi di Firenze, v.le Morgagni 85, I-50134 Firenze (Italy); INFN, sezione di Firenze, via G. Sansone 1, I-50019 Sesto Fiorentino (Italy); Azienda Ospedaliero-Universitaria Careggi, v.le Morgagni 85, I-50134 Firenze (Italy); Reggioli, V. [Dipartimento di Fisiopatologia Clinica, Universita degli Studi di Firenze, v.le Morgagni 85, I-50134 Firenze (Italy); Bruzzi, M. [INFN, sezione di Firenze, via G. Sansone 1, I-50019 Sesto Fiorentino (Italy); Dipartimento di Energetica, Universita degli Studi di Firenze, via S. Marta 3, I-50139 Firenze (Italy); Bucciolini, M. [Dipartimento di Fisiopatologia Clinica, Universita degli Studi di Firenze, v.le Morgagni 85, I-50134 Firenze (Italy); INFN, sezione di Firenze, via G. Sansone 1, I-50019 Sesto Fiorentino (Italy); Azienda Ospedaliero-Universitaria Careggi, v.le Morgagni 85, I-50134 Firenze (Italy); Civinini, C. [INFN, sezione di Firenze, via G. Sansone 1, I-50019 Sesto Fiorentino (Italy); Marrazzo, L. [Azienda Ospedaliero-Universitaria Careggi, v.le Morgagni 85, I-50134 Firenze (Italy); Menichelli, D. [INFN, sezione di Firenze, via G. Sansone 1, I-50019 Sesto Fiorentino (Finland) (Italy); Dipartimento di Energetica, Universita degli Studi di Firenze, via S. Marta 3, I-50139 Firenze (Italy); Pallotta, S. [Dipartimento di Fisiopatologia Clinica, Universita degli Studi di Firenze, v.le Morgagni 85, I-50134 Firenze (Italy); INFN, sezione di Firenze, via G. Sansone 1, I-50019 Sesto Fiorentino (Italy); Azienda Ospedaliero-Universitaria Careggi, v.le Morgagni 85, I-50134 Firenze (Italy); Randazzo, N. [INFN, sezione di Catania, via S. Sofia 64, I-95123 Catania (Italy); Sipala, V. [INFN, sezione di Catania, via S. Sofia 64, I-95123 Catania (Italy); Dipartimento di Fisica, Universita degli Studi di Catania, via S. Sofia 64, I-95123 Catania (Italy)

    2010-01-11

    Proton imaging is not yet applied as a clinical routine, although its advantages have been demonstrated. In the context of quality assurance in proton therapy, proton images can be used to verify the correct positioning of the patient and to control the range of protons. Proton computed tomography (pCT) is a 3D imaging method appropriate for planning and verification of proton radiation treatments, because it allows evaluating the distributions of proton stopping power within the tissues and can be directly utilized when the patient is in the actual treatment position. The aim of the PRoton IMAging experiment, supported by INFN, and the PRIN 2006 project, supported by MIUR, is to realize a proton computed radiography (pCR) prototype for reconstruction of proton images from a single projection in order to validate the technique with pre-clinical studies and, eventually, to conceive the configuration of a complete pCT system. A preliminary experiment performed at the 250 MeV proton synchrotron of Loma Linda University Medical Center (LLUMC) allowed acquisition of experimental data before the completion of PRIMA project's prototype. In this paper, the results of the LLUMC experiment are reported and the reconstruction of proton images of two phantoms is discussed.

  1. Radiography students' clinical learning styles.

    Science.gov (United States)

    Ward, Patti; Makela, Carole

    2010-01-01

    To examine the common learning styles of radiography students during clinical practice. Descriptive research methodology, using a single self-report questionnaire, helped to identify common learning styles of radiography students during clinical practice. The results indicated that 3 learning styles predominate among radiography students during clinical practice: task oriented, purposeful and tentative. Insight into clinical practice learning styles can help students understand how they learn and allow them to recognize ways to maximize learning. It also heightens awareness among clinical instructors and technologists of the different learning styles and their relevance to clinical practice education.

  2. Consumption of industrialized food by infants attending child day care centers.

    Science.gov (United States)

    Toloni, Maysa Helena de A; Longo-Silva, Giovana; Konstantyner, Tulio; Taddei, José Augusto de A C

    2014-03-01

    To identify the age of introduction of petit suisse cheese and instant noodles in the diet of infants attending nurseries of public day care centers and to compare the nutritional composition of these foods with the healthy recommended diet (breast milk and salt meal) for this age, in order to estimate nutritional errors. Cross-sectional study of 366 children (from nine to 36 months old) who attended day care centers, whose mothers were interviewed about the age of introduction of those foods. The means of the nutrients indicated on the labels of the most consumed brands were considered. For the calculation of the percent composition of breast milk and salt meal, Tables of Food Composition were used. To assess the nutritional adequacy, we used the Dietary Reference Intakes by age group. The percentage of adequacy evaluation of the petit suisse cheese and the instant noodles nutritional compositions was made by comparing them with those of the human milk and the salt meal, respectively. The petit suisse cheese and the instant noodles were consumed by 89.6 and 65.3% of the children in the first year of life. The percentages of adequacy for carbohydrates were more than twice and the percentages for sodium were 20 times higher than those found in the recommended foods. Both industrialized products are inappropriate for infants, emphasizing the need for adoption of norms that can inform health professionals, educators and parents about the risks of consumption.

  3. Consumption of industrialized food by infants attending child day care centers

    Directory of Open Access Journals (Sweden)

    Maysa Helena de A. Toloni

    2014-03-01

    Full Text Available Objective: To identify the age of introduction of petit suisse cheese and instant noodles in the diet of infants attending nurseries of public day care centers and to compare the nutritional composition of these foods with the healthy recommended diet (breast milk and salt meal for this age, in order to estimate nutritional errors. Methods: Cross-sectional study of 366 children (from nine to 36 months old who attended day care centers, whose mothers were interviewed about the age of introduction of those foods. The means of the nutrients indicated on the labels of the most consumed brands were considered. For the calculation of the percent composition of breast milk and salt meal, Tables of Food Composition were used. To assess the nutritional adequacy, we used the Dietary Reference Intakes by age group. The percentage of adequacy evaluation of the petit suisse cheese and the instant noodles nutritional compositions was made by comparing them with those of the human milk and the salt meal, respectively. Results: The petit suisse cheese and the instant noodles were consumed by 89.6 and 65.3% of the children in the first year of life. The percentages of adequacy for carbohydrates were more than twice and the percentages for sodium were 20 times higher than those found in the recommended foods. Conclusions: Both industrialized products are inappropriate for infants, emphasizing the need for adoption of norms that can inform health professionals, educators and parents about the risks of consumption.

  4. Digital Radiography Qualification of Tube Welding

    Science.gov (United States)

    Carl, Chad

    2012-01-01

    The Orion Project will be directing Lockheed Martin to perform orbital arc welding on commodities metallic tubing as part of the Multi Purpose Crew Vehicle assembly and integration process in the Operations and Checkout High bay at Kennedy Space Center. The current method of nondestructive evaluation is utilizing traditional film based x-rays. Due to the high number of welds that are necessary to join the commodities tubing (approx 470), a more efficient and expeditious method of nondestructive evaluation is desired. Digital radiography will be qualified as part of a broader NNWG project scope.

  5. Experiments on muon radiography with emulsion track detectors

    Directory of Open Access Journals (Sweden)

    Aleksandrov Andrey

    2016-01-01

    Full Text Available Muon radiography is a method of study the internal structure of large natural and industrial objects based on sensing an object with a flux of cosmic muons with their subsequent registration and analysis of the pattern of their dispersion, or conplete (or partial absorption. The Lebedev Physical Institute of the Russian Academy of Sciences and the Skobeltsyn Institute of Nuclear Physics of Moscow State University have started a series of muon radiography experiments with nuclear emulsion detectors. As a result, the optimal conditions for experiment arrangement have been determined, algorithms of data processing have been worked out, and peculiarities of the method have been ultimately investigated.

  6. An Assessment of Energy-Related Career Paths of Senior Industrial Assessment Center Program Alumni

    Energy Technology Data Exchange (ETDEWEB)

    Martin, M.A.

    2003-10-20

    The purpose of this study was to assess the career paths of alumni from the U.S. Department of Energy's Industrial Assessment Center (IAC) program. IAC was originally named the Energy Analysis and Diagnostic Center (EADC) program when it began in association with four schools in 1976. The current IAC program provides funding to 26 engineering colleges, located in centers across the United States, to conduct energy, waste, and productivity assessments for small- to medium-sized manufacturing establishments within their respective regions. Through part-time employment with the university, students receive training and in turn conduct assessments for local manufacturers, under the direct supervision of engineering faculty. Annually, IAC participants conduct over 700 assessments, and each assessment generates recommendations for energy savings, energy cost savings, and waste and productivity cost savings customized for individual clients. An earlier study determined that energy savings could be attributed to alumni of the IAC program who take their IAC experiences with them to the professional workplace. During their careers, the alumni conduct additional energy assessments as well as influence energy efficiency through design, teaching and training, and other activities. Indeed, a significant level of program benefits can be attributed to the alumni. This project addressed such specific questions as: How many years after graduation are IAC alumni involved in energy-efficiency activities? What different methods do they use to influence energy-efficiency decisions? To answer these questions, the University of Tennessee, Knoxville (UT) surveyed IAC senior alumni, defined as those who graduated in 1995 or earlier. Section 2 describes the survey used in this research. The actual survey can be found in Appendix A. Section 3 describes our approach to data collection. Section 4 presents descriptive statistics about the senior alumni who responded to the survey. Section 5

  7. Bone X-Ray (Radiography)

    Medline Plus

    Full Text Available ... Us News Physician Resources Professions Site Index A-Z X-ray (Radiography) - Bone Bone x-ray uses ... assess trauma patients in emergency departments. A CT scan can image complicated fractures, subtle fractures or dislocations. ...

  8. Abdomen X-Ray (Radiography)

    Science.gov (United States)

    ... Professions Site Index A-Z X-ray (Radiography) - Abdomen Abdominal x-ray uses a very small dose ... to produce pictures of the inside of the abdominal cavity. It is used to evaluate the stomach, liver, ...

  9. Proton Radiography (pRad)

    Data.gov (United States)

    Federal Laboratory Consortium — The proton radiography project has used 800 MeV protons provided by the LANSCE accelerator facility at LANL, to diagnose more than 300 dynamic experiments in support...

  10. Review and Prospect of Cobalt-60 Digital Radiography Inspection Technology

    OpenAIRE

    AN Ji-gang

    2015-01-01

    This article is a review and prospect of the research, development and industrialization of Cobalt-60 digital radiography inspection technology based on the national requirements in the recent 20 years, which is leaded by Institute of Nuclear and New Energy Technology (INET) of TsinghuaUniversity. The research purpose, innovative approach and main academic achievements of this technology were described systematically. The industrial equipment varieties, performance, running condition and appl...

  11. A Selection Model to Logistic Centers Based on TOPSIS and MCGP Methods: The Case of Airline Industry

    Directory of Open Access Journals (Sweden)

    Kou-Huang Chen

    2014-01-01

    Full Text Available The location selection of a logistics center is a crucial decision relating to cost and benefit analysis in airline industry. However, it is difficult to be solved because there are many conflicting and multiple objectives in location problems. To solve the problem, this paper integrates fuzzy technique for order preference by similarity to an ideal solution (TOPSIS and multichoice goal programming (MCGP to obtain an appropriate logistics center from many alternative locations for airline industry. The proposed method in this paper will offer the decision makers (DMs to set multiple aspiration levels for the decision criteria. A numerical example of application is also presented.

  12. 2007 University Exemplary Department Award honors industrial and systems engineering; apparel, housing, and resource management; and University Academic Advising Center

    OpenAIRE

    Owczarski, Mark

    2007-01-01

    The Grado Department of Industrial and Systems Engineering in the College of Engineering; the Department of Apparel, Housing, and Resource Management in the College of Liberal Arts and Human Sciences; and University Academic Advising Center will receive the 2007 University Exemplary Department Awards at ceremonies to be held Tuesday, Nov. 27 at The Inn at Virginia Tech.

  13. Upper Gastrointestinal (GI) Tract X-Ray (Radiography)

    Science.gov (United States)

    ... Site Index A-Z X-ray (Radiography) - Upper GI Tract Upper gastrointestinal tract radiography or upper GI ... GI) Tract X-ray? What is Upper Gastrointestinal (GI) Tract Radiography? Upper gastrointestinal tract radiography, also called ...

  14. Lower Gastrointestinal (GI) Tract X-Ray (Radiography)

    Science.gov (United States)

    ... Site Index A-Z X-ray (Radiography) - Lower GI Tract Lower gastrointestinal tract radiography or lower GI ... of Lower GI Tract Radiography? What is Lower GI Tract X-ray Radiography (Barium Enema)? Lower gastrointestinal ( ...

  15. Use of fluorescent screens for isotope radiography

    Energy Technology Data Exchange (ETDEWEB)

    Hubbard, S. K.

    1979-01-01

    Radiographic examination can be performed on items beyond the limitation of conventional isotope radiography without a great loss of resolution. With proper film and screen selection and scatter radiation control, fluorescent screens can be a valuable additional tool for radiography.

  16. Characterization and adjustment of the neutron radiography facility of the RP-10 nuclear reactor

    CERN Document Server

    Ravello-R, Y R

    2001-01-01

    The main aim of this work was to characterize and adjust the neutron radiography facility of the RP-10 nuclear reactor, and therefore be able to offer with this technique services to the industry and research centers in general. This technique will be complemented with others such as x-rays and gamma radiography. First, the shielding capacity of the facility was analyzed, proving that it complies with the radiological safety requirements established by the radiological safety code. Then gamma filtration tests were conducted in order to implement the direct method for image formation, optical density curves were built according to the thickness of the gamma filter, the type of film and the type of irradiation. Also, the indirect method for image formation was implemented for two types of converters: indium and dysprosium. Growth curves for optical density were also made according to contact time between converter-film, for different types of films. The resolution of the facility was also analyzed using two met...

  17. A WEB-BASED FRAMEWORK FOR VISUALIZING INDUSTRIAL SPATIOTEMPORAL DISTRIBUTION USING STANDARD DEVIATIONAL ELLIPSE AND SHIFTING ROUTES OF GRAVITY CENTERS

    Directory of Open Access Journals (Sweden)

    Y. Song

    2017-09-01

    Full Text Available Analysing spatiotemporal distribution patterns and its dynamics of different industries can help us learn the macro-level developing trends of those industries, and in turn provides references for industrial spatial planning. However, the analysis process is challenging task which requires an easy-to-understand information presentation mechanism and a powerful computational technology to support the visual analytics of big data on the fly. Due to this reason, this research proposes a web-based framework to enable such a visual analytics requirement. The framework uses standard deviational ellipse (SDE and shifting route of gravity centers to show the spatial distribution and yearly developing trends of different enterprise types according to their industry categories. The calculation of gravity centers and ellipses is paralleled using Apache Spark to accelerate the processing. In the experiments, we use the enterprise registration dataset in Mainland China from year 1960 to 2015 that contains fine-grain location information (i.e., coordinates of each individual enterprise to demonstrate the feasibility of this framework. The experiment result shows that the developed visual analytics method is helpful to understand the multi-level patterns and developing trends of different industries in China. Moreover, the proposed framework can be used to analyse any nature and social spatiotemporal point process with large data volume, such as crime and disease.

  18. a Web-Based Framework for Visualizing Industrial Spatiotemporal Distribution Using Standard Deviational Ellipse and Shifting Routes of Gravity Centers

    Science.gov (United States)

    Song, Y.; Gui, Z.; Wu, H.; Wei, Y.

    2017-09-01

    Analysing spatiotemporal distribution patterns and its dynamics of different industries can help us learn the macro-level developing trends of those industries, and in turn provides references for industrial spatial planning. However, the analysis process is challenging task which requires an easy-to-understand information presentation mechanism and a powerful computational technology to support the visual analytics of big data on the fly. Due to this reason, this research proposes a web-based framework to enable such a visual analytics requirement. The framework uses standard deviational ellipse (SDE) and shifting route of gravity centers to show the spatial distribution and yearly developing trends of different enterprise types according to their industry categories. The calculation of gravity centers and ellipses is paralleled using Apache Spark to accelerate the processing. In the experiments, we use the enterprise registration dataset in Mainland China from year 1960 to 2015 that contains fine-grain location information (i.e., coordinates of each individual enterprise) to demonstrate the feasibility of this framework. The experiment result shows that the developed visual analytics method is helpful to understand the multi-level patterns and developing trends of different industries in China. Moreover, the proposed framework can be used to analyse any nature and social spatiotemporal point process with large data volume, such as crime and disease.

  19. Neutron Radiography Facility at IBR-2 High Flux Pulsed Reactor: First Results

    Science.gov (United States)

    Kozlenko, D. P.; Kichanov, S. E.; Lukin, E. V.; Rutkauskas, A. V.; Bokuchava, G. D.; Savenko, B. N.; Pakhnevich, A. V.; Rozanov, A. Yu.

    A neutron radiography and tomography facilityhave been developed recently at the IBR-2 high flux pulsed reactor. The facility is operated with the CCD-camera based detector having maximal field of view of 20x20 cm, and the L/D ratio can be varied in the range 200 - 2000. The first results of the radiography and tomography experiments with industrial materials and products, paleontological and geophysical objects, meteorites, are presented.

  20. Practical application of suspension criteria scenarios in general radiography, computed radiography,digital radiography and fluoroscopy.

    Science.gov (United States)

    O'Connor, U; Gallagher, A; O'Reilly, G; Dowling, A; Malone, J F

    2013-02-01

    Radiological equipment must be assessed against criteria for acceptability to ensure that it meets the minimum standards for patient safety. This assessment is typically led by a medical physicist with input from radiology staff and the equipment supplier. Equipment that does not meet the criteria requires action and may be suspended from clinical use. European Commission report RP 91 will be revised and replaced as RP 162. It has been drawn up to aid medical physicists with the assessment process and provide guidance on suspension levels. This paper details several cases where the criteria in the proposed RP 162 were applied in general radiography, computed radiography, digital radiography and fluoroscopy. The factors considered by the medical physicist and the outcome of each case are presented. The proposed RP 162 report improves on its predecessor and provides a robust set of criteria for ensuring that patient safety within the EU medical exposures framework is optimised.

  1. Application of computed radiography for power plant tube

    Energy Technology Data Exchange (ETDEWEB)

    Chnag, Hee Jun; Kim, Sun Je; Yang, Yun Sick; Kim, Jong Duck; Lim, Sung Hee [Dosan Heavey Industries and Constrution Co.,Ltd, Changwon (Korea, Republic of); Park, Young Ha [Shinki Commercial Co.,Ltd, Seoul (Korea, Republic of)

    2005-05-15

    For radiographic examination, it is imperative that the film characteristics be determined so that optimal test conditions, and the result thereof, can be verified by analyzing the film values with regard to different radiation sources, and for standardizing the characteristics such as sensitivity, exposure thickness range (latitude) and maximum and minimum exposure dose, The research presented in this paper was aimed at evaluating the radioactive sensitivity characteristics of the Image Plate, in lieu of film, as used in Computer Radiography for various radiation sources, in order to apply this newly developed technology in other industrial fields, and in particular, the Power Plant industry. Several possibilities and improvements were discovered with the substitution of Computer Radiography for Conventional Film Radiographic Test.

  2. Model-centered approach to early planning and design of an eco-industrial park around an oil refinery.

    Science.gov (United States)

    Zhang, Xiangping; Strømman, Anders H; Solli, Christian; Hertwich, Edgar G

    2008-07-01

    Industrial symbiosis promises environmental and economic gains through a utilization of the waste of some processes as a resource for other processes. Because of the costs and difficulties of transporting some wastes, the largest theoretical potential for industrial symbiosis is given when facilities are colocated in an eco-industrial park (EIP). This study proposes a model-centered approach with an eight-step procedure for the early planning and design of an eco-industrial park considering technical and environmental factors. Chemical process simulation software was used to model the energy and material flows among the prospective members and to quantify the benefits of integration among different firms in terms of energy and resources saved as compared to a reference situation. Process simulation was based on a combination of physical models of industrial processes and empirical models. The modeling allows for the development and evaluation of different collaboration opportunities and configurations. It also enables testing chosen configurations under hypothetical situations or external conditions. We present a case study around an existing oil and gas refinery in Mongstad, Norway. We used the approach to propose the colocation of a number of industrial facilities around the refinery, focused on integrating energy use among the facilities. An EIP with six main members was designed and simulated, matching new hypothetical members in size to the existing operations, modeling material and energy flows in the EIP, and assessing these in terms of carbon and hydrogen flows.

  3. People Centered Innovation: Enabling Lean Integrated Project Delivery and Disrupting the Construction Industry for a More Sustainable Future

    Directory of Open Access Journals (Sweden)

    William Paolillo

    2016-01-01

    Full Text Available People-centered innovation is a paradigm shift in the construction industry. It is derived from the supposition that people not methods, schedules, or budgets deliver projects. Our data suggest that a multilevel, multidisciplinary project team through shared vision, values, and a common vernacular defines, designs, and delivers more successful projects than traditional methods. These projects meet the needs of shareholders, the community, stakeholders, and the planet. We employ the concepts of emotional intelligence and agency theory to explain an integrated project delivery (IPD construction project using lean tactics that not only delivered, but also exceeded expectations resulting in a six-month schedule acceleration and $60M savings over the original estimated cost of the project calculated assuming traditional project delivery methods. The safety rating for this project was 50% better than the national average and the expected improvement in operating margin for the new building is 33% greater. This paper introduces the notion of people-centered innovation to an industry that has struggled to adapt and show positive results over recent decades. Our case study describes the significance of people-centered innovation in construction project delivery. We discuss the implications for the construction industry going forward.

  4. Polarized neutron radiography with a periscope

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, Michael; Neubauer, Andreas; Muehlbauer, Martin; Schillinger, Burkhard; Pfleiderer, Christian; Boeni, Peter [Technische Universitaet Muenchen, Physik Department, E21, Garching (Germany); Calzada, Elbio, E-mail: michael.schulz@frm2.tum.d [Technische Universitaet Muenchen, Forschungsneutronenquelle Heinz Maier Leibnitz (FRM II), Garching (Germany)

    2010-01-01

    The interaction of the magnetic moment of the neutron with magnetic fields provides a powerful probe for spatially resolved magnetisation measurements in magnetic materials. We have tested a periscope as a new type of polarizer providing neutron beams with a high polarization and a low divergence. The observed inhomogeneity of the beam caused by the waviness of the glass substrates was quantified by means of Monte-Carlo simulations using the software package McStas. The results show that beams of high homogeneity can be produced if the waviness is reduced to below 1.0{center_dot}10{sup -5} rad. Finally, it is shown that radiography with polarized neutrons is a powerful method for measuring the spatially resolved magnetisation in optically float-zoned samples of the weak itinerant ferromagnet Ni{sub 3}Al, thereby aiding the identification of the appropriate growth parameters.

  5. Development of Graduate Course Education by Industry Collaboration in Center for Engineering Education Development, CEED

    Science.gov (United States)

    Noguchi, Toru; Yoshikawa, Kozo; Nakamura, Masato; Kaneko, Katsuhiko

    New education programs for engineering graduate courses, and the achievements are described. Following the previous reports on overseas and domestic internship2) , 3) , this article states other common programs ; seminars on state of technologies in industries, practical English and internationalization programs, and a program to accept overseas internship students. E-learning system to assist off-campus students is also described. All these programs are developed and conducted by specialist professors invited from industries and national institutions, in collaboration with faculty professors. Students learn how the engineering science apply to the practical problems, acquire wider view and deeper understanding on industries, and gain abilities to act in global society including communication skill, those are not taught in classrooms and laboratories. Educational effects of these industry collaborated programs is significant to activate the graduate course education, although the comprehensive evaluation is the future subject.

  6. High Brightness Neutron Source for Radiography

    Energy Technology Data Exchange (ETDEWEB)

    Cremer, J. T.; Piestrup, Melvin, A.; Gary, Charles, K.; Harris, Jack, L. Williams, David, J.; Jones, Glenn, E.; Vainionpaa, J. , H.; Fuller, Michael, J.; Rothbart, George, H.; Kwan, J., W.; Ludewigt, B., A.; Gough, R.., A..; Reijonen, Jani; Leung, Ka-Ngo

    2008-12-08

    of yield of two orders of magnitude. The first fast neutron radiographic images were obtained using neutron cameras and a new fast neutron generator. These early images demonstrated the feasibility of using fast neutrons for imaging and penetrating thick objects of high density and imaging. Fast neutrons can be used to image low atomic number materials (e.g. plastics, explosives, lubricants and ceramics) that are shielded by high density materials (e.g. lead, tungsten and uranium). Fast neutron radiography could be used as a means to screen weapons for flaws and chemical stability. X-ray radiography can not easily do this. Fast neutron imaging is technically difficult and, consequently, a completely undeveloped market. Two of the generators were designed to have small source size and high brightness, ideal for fast-neutron imaging. With these generators we successfully used two fast neutron cameras: one developed by us, and another developed by a collaborator, Commonwealth Scientific and Industrial Research Organization, CSIRO. We have successfully used these cameras to obtain low resolution images of various objects such as pipe fittings filled with water and other mechanical objects. Higher resolution and contrast images are expected by decreasing the source size and increasing generator yield.

  7. Regional Rural Tourist Recreation Shopping Centers: A New Concept in the Leisure Industry

    Science.gov (United States)

    Nicholls, Leland L.

    1975-01-01

    A rural tourist-recreation shopping center is defined as an area relatively accessible to city dwellers that can be developed for recreation purposes. Twenty-three such areas have been identified in the Appalachian Highlands. (PS)

  8. Development of the neutron radiography facility and its installation in HANARO

    CERN Document Server

    Nam, K Y; Kim, H J; Kim, Y K; Lee, C H; Lim, I C; Sim, C M

    2001-01-01

    HANARO neutron radiography facility has been developed to do industrial and scientific research and developments. Characterization and detailed evaluation of the NRF system after its development are indispensible information to research and application by using the system. This report is based on the results from the neutron radiography facility, installation works for the last several years from 1994 to 1997 and characterization work thereafter. This report describes the principle of neutron radiography, theoretical aspects in several parts, overall introduction of the HANARO neutron radiography facility, and discussions in each characteristics in detail. As key components of the NRF, in-pile collimator, Bi filter, L/D ratio, thermal neutron flux and its distribution in radiation active area were studied and described. In addition to these parts, several minor parts and auxiliary aspects were also mentioned. The imaging methods and characteristics in each one are described shortly and categorized, and a prot...

  9. The application and development of radiography technology based on x-ray

    Science.gov (United States)

    Chen, Hao; Xu, Zhou; Li, Ming

    2009-07-01

    Modern Radiography technology was combined with radiation physics and modern imaging processing, which was an important branch of information obtainment and processing. We can get the inside information of the object, by the X ray's attenuation when the ray penetrated the object, and depending on the computer's fast processing, we can see the slice imaging of the object. Computerized Tomography, Computerized Laminography, and Digital Radiography were important parts in Radiography. The institute of applied electronics, CAEP in the research of intense radiation had developed several advanced radiation sources and some advanced radiography imaging systems, for example, S-band small spot linear accelerator, full solid state modulator, C-band linear accelerator, high energy Tera-hertz radiation source and CT technology based on cone beam, DR technology, CL Technology etc. Such imaging systems had been applied in industrial NDT/NDE, security check, medical diagnosis, petroleum and gas pipeline inspection system etc.

  10. National Composite Center-A new roof for composite industries in Malaysia

    Science.gov (United States)

    Abdullah, Abu; Yuhazri, M. Y.; Sulaiman, Mohd Yusoff

    2016-03-01

    Today's Malaysia has more than 70 companies that are actively involved in composite activities. The activities are ranging from various business sectors, using different technology and material. Composites has been used in a wide range of applications in Malaysia and contributes to growth in a diverse range of industry value chains from utilities through to boat building, manufacturing and industrial applications, aerospace, consumer products and construction products. Thus, a key part of this strategy is the establishment of the National Composites Centre (NCC), which will bring together dynamic companies and enterprising academics to develop new technologies for the design and rapid manufacture of high-quality composite products.

  11. A New Neutron Radiography / Tomography / Imaging Station DINGO at OPAL

    Science.gov (United States)

    Garbe, U.; Randall, T.; Hughes, C.; Davidson, G.; Pangelis, S.; Kennedy, S. J.

    A new neutron radiography / tomography / imaging instrument DINGO was built to support the area of neutron imaging research (neutron radiography/tomography) at ANSTO. The instrument is designed for an international user community and for routine quality control for defense, industrial, cultural heritage and archaeology applications. In the industrial field it provides a useful tool for studying cracking and defects in steel or other metals. The instrument construction was completed at the end of June 2013 and it is currently in the hot commissioning stage. The usable neutron flux is mainly determined by the neutron source, but it depends on the instrument position and the resolution. The instrument position for DINGO is the thermal neutron beam port HB-2 in the reactor hall. The measured flux (using gold foil) for an L/D of approximately 500 at HB-2 is 5.3*107 [n/cm2s], which is in a similar range to other facilities. A special feature of DINGO is the in-pile collimator position in front of the main shutter at HB-2. The collimator offers two pinholes with a possible L/D of 500 and 1000. A secondary collimator separates the two beams by blocking one and positions another aperture for the other beam. The whole instrument operates in two different positions, one for high resolution and one for high speed. In the current configuration DINGO measured first radiography and tomography data sets on friendly user test samples.

  12. Institutional dynamic of the call center industry in Denmark and France

    DEFF Research Database (Denmark)

    Sørensen, Ole H.; Beraud, Mathieu; Colin, Thierry

    2005-01-01

    The call centre development is substantially increasing in the most part of industrialized countries. Coming to the fore and seeking for staff, this sector is still looking for benchmarks, especially in terms of employment. Currently it can be said that the sector is under construction since its ...

  13. Institutional dynamic of the call center industry in Denmark and France

    DEFF Research Database (Denmark)

    Sørensen, Ole H.; Beraud, Mathieu; Colin, Thierry

    2005-01-01

    The call centre development is substantially increasing in the most part of industrialized countries. Coming to the fore and seeking for staff, this sector is still looking for benchmarks, especially in terms of employment. Currently it can be said that the sector is under construction since its ...

  14. Industry

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, Lenny; Roy, Joyashree; Delhotal, K. Casey; Harnisch, Jochen; Matsuhashi, Ryuji; Price, Lynn; Tanaka, Kanako; Worrell, Ernst; Yamba, Francis; Fengqi, Zhou; de la Rue du Can, Stephane; Gielen, Dolf; Joosen, Suzanne; Konar, Manaswita; Matysek, Anna; Miner, Reid; Okazaki, Teruo; Sanders, Johan; Sheinbaum Parado, Claudia

    2007-12-01

    This chapter addresses past, ongoing, and short (to 2010) and medium-term (to 2030) future actions that can be taken to mitigate GHG emissions from the manufacturing and process industries. Globally, and in most countries, CO{sub 2} accounts for more than 90% of CO{sub 2}-eq GHG emissions from the industrial sector (Price et al., 2006; US EPA, 2006b). These CO{sub 2} emissions arise from three sources: (1) the use of fossil fuels for energy, either directly by industry for heat and power generation or indirectly in the generation of purchased electricity and steam; (2) non-energy uses of fossil fuels in chemical processing and metal smelting; and (3) non-fossil fuel sources, for example cement and lime manufacture. Industrial processes also emit other GHGs, e.g.: (1) Nitrous oxide (N{sub 2}O) is emitted as a byproduct of adipic acid, nitric acid and caprolactam production; (2) HFC-23 is emitted as a byproduct of HCFC-22 production, a refrigerant, and also used in fluoroplastics manufacture; (3) Perfluorocarbons (PFCs) are emitted as byproducts of aluminium smelting and in semiconductor manufacture; (4) Sulphur hexafluoride (SF{sub 6}) is emitted in the manufacture, use and, decommissioning of gas insulated electrical switchgear, during the production of flat screen panels and semiconductors, from magnesium die casting and other industrial applications; (5) Methane (CH{sub 4}) is emitted as a byproduct of some chemical processes; and (6) CH{sub 4} and N{sub 2}O can be emitted by food industry waste streams. Many GHG emission mitigation options have been developed for the industrial sector. They fall into three categories: operating procedures, sector-wide technologies and process-specific technologies. A sampling of these options is discussed in Sections 7.2-7.4. The short- and medium-term potential for and cost of all classes of options are discussed in Section 7.5, barriers to the application of these options are addressed in Section 7.6 and the implication of

  15. Fracture healing: direct magnification versus conventional radiography

    Energy Technology Data Exchange (ETDEWEB)

    Link, T.M. [Dept. of Clinical Radiology, Westfaelische Wilhelms-Univ., Muenster (Germany); Kessler, T. [Dept. of Traumatic and Hand Surgery, Westfaelische Wilhelms-Univ., Muenster (Germany); Lange, T. [Dept. of Clinical Radiology, Westfaelische Wilhelms-Univ., Muenster (Germany); Overbeck, J. [Dept. of Traumatic and Hand Surgery, Westfaelische Wilhelms-Univ., Muenster (Germany); Fiebich, M. [Dept. of Clinical Radiology, Westfaelische Wilhelms-Univ., Muenster (Germany); Peters, P.E. [Dept. of Clinical Radiology, Westfaelische Wilhelms-Univ., Muenster (Germany)

    1994-08-01

    The aim of the study was to evaluate the potential of magnification radiography in diagnosing fracture healing and assessing its complications. Seventy-three patients with fractures or who had undergone osteotomy were radiographed with both conventional (non-magnified) and magnification (5-fold) techniques. Since 10 patients were radiographed twice and 1 three times, 83 radiographs using each technique were obtained. All radiographs were analysed and the findings correlated with the patients` follow-up studies. The microfocal X-ray unit used for magnification radiography had a focal spot size of 20-130 {mu}m. As an imaging system, digital luminescence radiography was employed with magnification, while normal film-screen systems were used with conventional radiography. Magnification radiography proved superior to conventional radiography in 47% of cases: endosteal and periosteal callus formations were seen earlier and better in 26 cases, and osseous union could be evaluated with greater certainty in 33 cases. In 49% of cases magnification radiography was equal and in 4% inferior to conventional radiography. Additionally an ``inter-observer analysis`` was carried out. Anatomical and pathological structures were classified into one of four grades. Results were significantly (P < 0.01) better using magnification radiography. We conclude that the magnification technique is a good method for monitoring fracture healing in its early stages. (orig.)

  16. Digital chest radiography: collimation and dose reduction

    DEFF Research Database (Denmark)

    Debess, Jeanne; Johnsen, Karen Kirstine; Vejle-Sørensen, Jens Kristian

    Purpose: Quality improvement of basic radiography focusing on collimation and dose reduction in digital chest radiography Methods and Materials:A retrospective study of digital chest radiography is performed to evaluate the primary x-ray tube collimation of the PA and lateral radiographs. Data from...... of clinical supervisors. Optimal collimation is determined by European and Regional Danish guidelines. The areal between current and optimal collimation is calculated. The experimental research is performed in September - October 2014 Siemens Axiom Aristos digital radiography system DR using 150 kV, 1,25 -3...

  17. The Cooperation Between Poison Control Center and Organized Industrial District for Chemical Disaster Prevention

    Science.gov (United States)

    2001-09-01

    prevention efforts. A hotline line between center and district was established, while Tomes Plus and Intox Programmes adding Micromedex Computer Programme...to be 10342. Questionnaires revealed 47 different chemical agents. Two Safety discettes for each plant were prepared with reference to Micromedex Tomes

  18. 15 CFR 291.4 - National industry-specific pollution prevention and environmental compliance resource centers.

    Science.gov (United States)

    2010-01-01

    ... and develop the services to its customers. The centers should rarely, if ever, perform research, but... proposal must set forth clearly defined, effective mechanisms for delivery of services to target population..., external evaluation for assessing outcomes of the activity, and “customer satisfaction” measures...

  19. Bright Flash Neutron Radiography at the McClellan Nuclear Research Reactor

    Science.gov (United States)

    Lerche, M.; Tremsin, A. S.; Schillinger, B.

    The University of California, Davis McClellan Nuclear Research Center (MNRC) operates a 2 MW TRIGATM reactor, which is currently the highest power TRIGATM reactor in the United States. The Center was originally build by the US Air Force to detect hidden defects in aircraft structures using neutron radiography; the Center can accommodate samples as large as 10.00 m long, 3.65 m high, and weighing up to 2,270 kg. The MNRC reactor can be pulsed to 350 MW for about 30 ms (FWHM). The combination of a short neutron pulse with a fast microchannel plate based neutron detector enables high-resolution flash neutron radiography to complement conventional neutron radiography

  20. Industrialization

    African Journals Online (AJOL)

    Lucy

    Second World era international system (1945-1990) may not have done any good to ... wedge between the capitalist and socialist blocs, not only blurred Third World .... Politics and the Stages of Economic Growth, Cambridge: Cambridge ... complex industries producing mainly for export, but also producing for local.

  1. Center for the Polyurethanes Industry summary of unpublished industrial hygiene studies related to the evaluation of emissions of spray polyurethane foam insulation.

    Science.gov (United States)

    Wood, Richard D

    2017-09-01

    Spray polyurethane foam (SPF) insulation is used as thermal insulation for residential and commercial buildings. It has many advantages over other forms insulation; however, concerns have been raised related to chemical emissions during and after application. The American Chemistry Council's (ACC's) Center for the Polyurethanes Industry (CPI) has gathered previously unpublished industrial hygiene air sampling studies submitted by member companies that were completed during an eight-year period from 2007-2014. These studies address emissions from medium density closed cell and low density open cell formulations. This article summarizes the results of personal and area air samples collected during application and post application of SPF to interior building surfaces in both laboratory and field environments. Chemicals of interest included: Volatile Organic Compounds (VOCs), methylene diphenyl diisocyanate (MDI), flame retardants, amine catalysts, blowing agents, and aldehydes. Overall, the results indicate that SPF applicators and workers in close proximity to the application are potentially exposed to MDI in excess of recommended and governmental occupational exposure limits and should use personal protective equipment (PPE) consisting of air supplied respirators and full-body protective clothing to reduce exposure. Catalyst emissions can be reduced by using reactive catalysts in SPF formulations, and mechanical ventilation is important in controlling emissions during and after application.

  2. New computed radiography processing condition for whole-spine radiography.

    Science.gov (United States)

    Sasagawa, Takeshi; Kunogi, Junichi; Masuyama, Shigeru; Ogihara, Satoshi; Takeuchi, Yosuke; Takeshita, Yujiro; Kamiya, Naokazu; Murakami, Hideki; Tsuchiya, Hiroyuki

    2011-12-06

    Computed radiography (CR) has many advantages compared with conventional radiographs, especially in image processing. Although CR is being used in chest radiography and mammography, it has not been applied to spine imaging. The purposes of this study were to formulate a set of new CR processing parameters and to test whether the resultant whole-spine radiographs visualized the spine more clearly than conventional images. This study included 29 patients who underwent whole-spine radiographs. We used 3 image processing methods to improve the clarity of whole-spine radiographs: gradation processing, dynamic range control processing, and multi-objective frequency processing. Radiograph definition was evaluated using vertebrae sampled from each region of the whole spine, specifically C4, C7, T8, T12, and L3; evaluation of the lateral view also included the sacral spine and femoral head. Image definition was assessed using a 3-point grading system. The conventional and processed CR images (both frontal and lateral views) were evaluated by 5 spine surgeons. In all spinal regions on both frontal and lateral views, the processed images showed statistically significantly better clarity than the corresponding conventional images, especially at T12, L3, the sacral spine, and the femoral head on the lateral view. Our set of new CR processing parameters can improve the clarity of whole-spine radiographs compared with conventional images. The greatest advantage of image processing was that it enabled clear depiction of the thoracolumbar junction, lumbar vertebrae, sacrum, and femoral head in the lateral view.

  3. Multiple imaging radiography at LNLS

    Energy Technology Data Exchange (ETDEWEB)

    Hoennicke, M.G. [LORXI, Departamento de Fisica, Universidade Federal do Parana, Caixa Postal 19091, 81531-990 Curitiba (Brazil)], E-mail: marcelohonnicke@yahoo.com.br; Cusatis, C. [LORXI, Departamento de Fisica, Universidade Federal do Parana, Caixa Postal 19091, 81531-990 Curitiba(Brazil); Antunes, A. [Departamento de Fisica Aplicada, Instituto de Fisica, Universidade de Sao Paulo, Caixa Postal 66318, 05315-970 Sao Paulo (Brazil); Safatle, A.M.V.; Barros, P.S.M. [Laboratorio de Oftalmologia Experimental e Comparativa, Departamento de Cirurgia, Faculdade de Medicina Veterinaria, Universidade de Sao Paulo, 05508-900 Sao Paulo (Brazil); Morelhao, S.L. [Departamento de Fisica Aplicada, Instituto de Fisica, Universidade de Sao Paulo, Caixa Postal 66318, 05315-970 Sao Paulo (Brazil)

    2008-01-11

    An analyzer-based X-ray phase-contrast imaging (ABI) setup has been mounted at the Brazilian Synchrotron Light Laboratory (LNLS) for multiple imaging radiography (MIR) purposes. The algorithm employed for treating the MIR data collected at LNLS is described, and its reliability in extracting the distinct types of contrast that can be obtained with MIR is demonstrated by analyzing a test sample (thin polyamide wire). As a practical application, the possibility of studying ophthalmic tissues, corneal sequestra in this case, via MIR is investigated.

  4. Computational radiology in skeletal radiography

    Energy Technology Data Exchange (ETDEWEB)

    Peloschek, Ph.; Nemec, S. [Computational Image Analysis and Radiology Lab (CIR), Department of Radiology, Medical University Vienna, Waehringer Guertel 18-20, A-1090 Vienna (Austria); Widhalm, P. [Computational Image Analysis and Radiology Lab (CIR), Department of Radiology, Medical University Vienna, Waehringer Guertel 18-20, A-1090 Vienna (Austria); Pattern Recognition and Image Processing Group, Department of Computer Aided Automation, Vienna University of Technology, Wiedner Hauptstrasse 8-10/020, A-1040 Vienna (Austria); Donner, R. [Computational Image Analysis and Radiology Lab (CIR), Department of Radiology, Medical University Vienna, Waehringer Guertel 18-20, A-1090 Vienna (Austria); Pattern Recognition and Image Processing Group, Department of Computer Aided Automation, Vienna University of Technology, Wiedner Hauptstrasse 8-10/020, A-1040 Vienna (Austria); Institute for Computer Graphics and Vision, Graz University of Technology, Inffeldgasse 16, A-8010 Graz (Austria); Birngruber, E. [Computational Image Analysis and Radiology Lab (CIR), Department of Radiology, Medical University Vienna, Waehringer Guertel 18-20, A-1090 Vienna (Austria); Thodberg, H.H. [Visiana Aps, Sollerodvej 57C, DK-2840 Holte (Denmark); Kainberger, F. [Computational Image Analysis and Radiology Lab (CIR), Department of Radiology, Medical University Vienna, Waehringer Guertel 18-20, A-1090 Vienna (Austria); Langs, G. [Computational Image Analysis and Radiology Lab (CIR), Department of Radiology, Medical University Vienna, Waehringer Guertel 18-20, A-1090 Vienna (Austria)], E-mail: georg.langs@meduniwien.ac.at

    2009-11-15

    Recent years have brought rapid developments in computational image analysis in musculo-skeletal radiology. Meanwhile the algorithms have reached a maturity that makes initial clinical use feasible. Applications range from joint space measurement to erosion quantification, and from fracture detection to the assessment of alignment angles. Current results of computational image analysis in radiography are very promising, but some fundamental issues remain to be clarified, among which the definition of the optimal trade off between automatization and operator-dependency, the integration of these tools into clinical work flow and last not least the proof of incremental clinical benefit of these methods.

  5. NEUTRON RADIOGRAPHY: A SECOND PROGRESS REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Berger, H

    1962-08-31

    The progress made on investigations of neutron radiography since October 1960 is discussed. The problems of the production of the neutron image will be discussed. The emphasis will be on the characteristics of many of the photographic imaging methods which can be used for neutron radiography. (auth)

  6. Process waste assessment for the Radiography Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, N.M.

    1994-07-01

    This Process Waste Assessment was conducted to evaluate the Radiography Laboratory, located in Building 923. It documents the processes, identifies the hazardous chemical waste streams generated by these processes, recommends possible ways to minimize waste, and serves as a reference for future assessments of this facility. The Radiography Laboratory provides film radiography or radioscopy (electronic imaging) of weapon and nonweapon components. The Radiography Laboratory has six x-ray machines and one gamma ray source. It also has several other sealed beta- and gamma-ray isotope sources of low microcurie ({mu}Ci) activity. The photochemical processes generate most of the Radiography Laboratory`s routinely generated hazardous waste, and most of that is generated by the DuPont film processor. Because the DuPont film processor generates the most photochemical waste, it was selected for an estimated material balance.

  7. Observer variation for radiography, computed tomography, and magnetic resonance imaging of occult hip fractures

    Energy Technology Data Exchange (ETDEWEB)

    Collin, David; Dunker, Dennis; Goethlin, Jan H (Dept. of Radiology, Sahlgrenska Univ. Hospital, Moelndal (Sweden)), email: david.collin@vgregion.se; Geijer, Mats (Center for Medical Imaging and Physiology, Skaane Univ. Hospital, Lund Univ., Lund (Sweden))

    2011-10-15

    Background Conventional radiography is insufficient for diagnosis in a small but not unimportant number of hip fractures, and secondary imaging with computed tomography (CT) or magnetic resonance imaging (MRI) is warranted. There are no convincing observer variation studies performed for conventional radiography or CT in occult fractures, and no large materials for MRI. Purpose To assess observer variation in radiography, CT and MRI of suspected occult, non-displaced hip fractures, and to evaluate to what extent observer experience or patient age may influence observer performance. Material and Methods A total of 375 patients after hip trauma where radiography was followed by CT or MRI to evaluate a suspected occult hip fracture were collected retrospectively from two imaging centers. After scoring by three observers with varying degrees of radiologic experience, observer variation was assessed by using linear weighted kappa statistics. Results For radiography, agreements between the three observers were moderate to substantial for intra capsular fractures, with kappa values in the ranges of 0.56-0.66. Kappa values were substantial for extracapsular fractures, in the ranges of 0.69-0.72. With increasing professional experience, fewer fractures were classified as equivocal at radiography. For CT and MRI, observer agreements were similar and almost perfect, with kappa values in the ranges of 0.85-0.97 and 0.93-0.97. Conclusion There were almost perfect observer agreements for CT and MRI in diagnosing non-displaced, occult hip fractures. Observer agreements for radiography were moderate to substantial, and observer experience influenced agreement only at radiography

  8. Marketing strategy adjustments in the ambulatory care center industry: implications for community pharmacy.

    Science.gov (United States)

    Phillips, J H

    1989-01-01

    Each stage of a product's life cycle requires marketing strategy modifications in response to changing demand levels. The purpose of this study was to investigate changes in ambulatory care center (ACC) operational characteristics indicative of product, market, and distribution channel adjustments that could have a competitive impact upon community pharmacy practice. A questionnaire was mailed to a national sample of 325 ACC managers. Evidence of new product feature additions includes increased emphasis on continued care and increased prevalence of prescription drug dispensing. Expansion into new market segments and distribution channels was demonstrated by increased participation in HMO and employer relationships. The observed adjustments in ACC marketing strategies present obvious challenges as well as less obvious opportunities for community pharmacy practice.

  9. Operator-centered control of a semi-autonomous industrial robot

    Energy Technology Data Exchange (ETDEWEB)

    Spelt, P.F. [Oak Ridge National Lab., TN (United States); Jones, S.L. [REMOTEC, Inc., Oak Ridge, TN (United States)

    1994-12-31

    This paper presents work done by Oak Ridge National Laboratory and Remotec, Inc., to develop a new operator-centered control system for Remotec`s Andros telerobot. Andros robots are presently used by numerous electric utilities, the armed forces, and numerous law enforcement agencies to perform tasks which are hazardous for human operators. This project has automated task components and enhanced the video graphics display of the robot`s position in the environment to significantly reduce operator workload. The procedure of automating a telerobot requires the addition of computer power to the robot, along with a variety of sensors and encoders to provide information about the robots performance in and relationship to its environment The resulting vehicle serves as a platform for research on strategies to integrate automated tasks with those performed by a human operator. The addition of these capabilities will greatly enhance the safety and efficiency of performance in hazardous environments.

  10. Non destructive testing and neutron radiography in 1994; Les controles non destructifs et la neutronographie en 1994

    Energy Technology Data Exchange (ETDEWEB)

    Bayon, G.

    1994-12-31

    Neutron radiography has been considered for a long time as a promising technique; however it plays a minor part in the world of non destructive testing today, due to the lack of suitable neutron sources and lack of new industrial applications. This paper reviews the present status of neutron sources, neutron radiography activities, especially in France (such as the neutron-capture-issued secondary radiation spectrometry), in nuclear, aerospace, aeronautical and metallurgical sectors, and the last applications of neutron dynamic imaging. 9 refs.

  11. A survey of digital radiography practice in four South African teaching hospitals: an illuminative study

    Science.gov (United States)

    Nyathi, T; Chirwa, TF; van der Merwe, DG

    2010-01-01

    Purpose: The purpose of this study was to assess radiographer familiarity and preferences with digital radiography in four teaching hospitals and thereafter make recommendations in line with the migration from screen film to digital radiography. Materials and methods: A questionnaire was designed to collect data from either qualified or student radiographers from four teaching hospitals. From the four teaching hospitals, there were a total of 205 potential respondents. Among other things, responses regarding experiences and preferences with digital radiography, quality control procedures, patient dose, advantages and disadvantages of digital radiography were sought. The information collected was based on self-reporting by the participants. The study is exploratory in nature and descriptive statistics were generated from the collected data using Microsoft Excel 2007 and StatsDirect software. Results: Sixty-three out of 205 (31%) radiographers from all the four radiology centers responded to the circulated questionnaire. Only 15% (8) of the qualified radiographers had 4 or more years of experience with digital radiography compared to 68% (36) for the same amount of experience with screen-film radiography. Sixty-one percent (38) of the participants had been exposed to digital radiography during their lectures while at university. A small proportion, 16% (10) of the respondents underwent formal training in quality control procedures on the digital X-ray units they were using. Slightly more than half (55%) of the participants felt it was easier for them to retake an image in digital radiography than in screen film radiography. Conclusion: The results of this survey showed that the participants are familiar with digital radiography and have embraced this relatively new technology as shown by the fact that they can identify both its advantages and disadvantages as applied to clinical practice. However, there are minimal quality control procedures specific to digital

  12. Time-gated energy-selected cold neutron radiography

    CERN Document Server

    McDonald, T E; Claytor, T N; Farnum, E H; Greene, G L; Morris, C

    1999-01-01

    A technique is under development at the Los Alamos Neutron Science Center (LANSCE), Manuel Lujan Jr. Neutron Scattering Center (Lujan Center) for producing neutron radiography using only a narrow energy range of cold neutrons. The technique, referred to as time-gated energy-selected (TGES) neutron radiography, employs the pulsed neutron source at the Lujan Center with time of flight to obtain a neutron pulse having an energy distribution that is a function of the arrival time at the imager. The radiograph is formed on a short persistence scintillator and a gated, intensified, cooled CCD camera is employed to record the images, which are produced at the specific neutron energy range determined by the camera gate. The technique has been used to achieve a degree of material discrimination in radiographic images. For some materials, such as beryllium and carbon, at energies above the Bragg cutoff the neutron scattering cross section is relatively high while at energies below the Bragg cutoff the scattering cross ...

  13. Assessing The Impact Of Computed Radiography And PACS

    Science.gov (United States)

    Hedgcock, Marcus W.; Kehr, Katherine

    1989-05-01

    Our institution (San Francisco VA Medical Center) is a VA pilot center for total digital imaging and PACS. Quantitative information about PACS impact on health care is limited, because no centers have done rigorous preimplementation studies. We are gathering quantitative service delivery and cost data before, during, and after stepwise implementation of computed radiography and PACS at our institution to define the impact on imaging service delivery. We designed a simple audit method using the x-ray request and time clocks to determine patient waiting time, imaging time, film use, image availability to the radiologist, matching of current with previous images, image availability to clinicians, and time to final interpretation. Our department model is a multichannel, mulitserver patient queue. Our current radiograph file is space limited, containing only one year of images; older images are kept in a remote file area in another building. In addition, there are 16 subfile areas within the Radiology Service and the medical center. Our preimplementation audit showed some long waiting times (40 minutes, average 20) and immediate retrieval of prior films in only 42% of cases, with an average retrieval time of 22 hours. Computed radiography and the optical archive have the potential to improve these figures. The audit will be ongoing and automated as implementation of PACS progresses, to measure service improvement and learning curve with the new equipment. We present the audit format and baseline preimplementation figures.

  14. A dose monitoring system for dental radiography

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chena; Lee, Sam Sun; Kim, Jo Eun; Huh, Kyung Hoe; Yi, Woo Jin; Heo, Min Suk; Choi, Soon Chul [Dept. of Oral and Maxillofacial Radiology and Dental Research Institute, School of Dentistry, Seoul National University, Seoul (Korea, Republic of); Symkhampha, Khanthaly [Dept. of Oral and Maxillofacial Radiology, Department of Basic Science, Faculty of Dentistry, University of Health Sciences, Vientiane (Lao People' s Democratic Republic); Lee, Woo Jin [Dept. of Interdisciplinary Program in Radiation, Applied Life Sciences Major, College of Medicine, BK21, and Dental Research Institute, Seoul National University, Seoul (Korea, Republic of); Yeom, Heon Young [School of Computer Science Engineering, Seoul National University, Seoul (Korea, Republic of)

    2016-06-15

    The current study investigates the feasibility of a platform for a nationwide dose monitoring system for dental radiography. The essential elements for an unerring system are also assessed. An intraoral radiographic machine with 14 X-ray generators and five sensors, 45 panoramic radiographic machines, and 23 cone-beam computed tomography (CBCT) models used in Korean dental clinics were surveyed to investigate the type of dose report. A main server for storing the dose data from each radiographic machine was prepared. The dose report transfer pathways from the radiographic machine to the main sever were constructed. An effective dose calculation method was created based on the machine specifications and the exposure parameters of three intraoral radiographic machines, five panoramic radiographic machines, and four CBCTs. A viewing system was developed for both dentists and patients to view the calculated effective dose. Each procedure and the main server were integrated into one system. The dose data from each type of radiographic machine was successfully transferred to the main server and converted into an effective dose. The effective dose stored in the main server is automatically connected to a viewing program for dentist and patient access. A patient radiation dose monitoring system is feasible for dental clinics. Future research in cooperation with clinicians, industry, and radiologists is needed to ensure format convertibility for an efficient dose monitoring system to monitor unexpected radiation dose.

  15. U.S. Department of Energy Regional Resource Centers Report: State of the Wind Industry in the Regions

    Energy Technology Data Exchange (ETDEWEB)

    Baranowski, Ruth [National Renewable Energy Lab. (NREL), Golden, CO (United St; Oteri, Frank [National Renewable Energy Lab. (NREL), Golden, CO (United St; Baring-Gould, Ian [National Renewable Energy Lab. (NREL), Golden, CO (United St; Tegen, Suzanne [National Renewable Energy Lab. (NREL), Golden, CO (United St

    2016-03-01

    The wind industry and the U.S. Department of Energy (DOE) are addressing technical challenges to increasing wind energy's contribution to the national grid (such as reducing turbine costs and increasing energy production and reliability), and they recognize that public acceptance issues can be challenges for wind energy deployment. Wind project development decisions are best made using unbiased information about the benefits and impacts of wind energy. In 2014, DOE established six wind Regional Resource Centers (RRCs) to provide information about wind energy, focusing on regional qualities. This document summarizes the status and drivers for U.S. wind energy development on regional and state levels. It is intended to be a companion to DOE's 2014 Distributed Wind Market Report, 2014 Wind Technologies Market Report, and 2014 Offshore Wind Market and Economic Analysis that provide assessments of the national wind markets for each of these technologies.

  16. A Collection-Distribution Center Location and Allocation Optimization Model in Closed-Loop Supply Chain for Chinese Beer Industry

    Directory of Open Access Journals (Sweden)

    Kai Kang

    2017-01-01

    Full Text Available Recycling waste products is an environmental-friendly activity that can result in manufacturing cost saving and economic efficiency improving. In the beer industry, recycling bottles can reduce manufacturing cost and the industry’s carbon footprint. This paper presents a model for a collection-distribution center location and allocation problem in a closed-loop supply chain for the beer industry under a fuzzy random environment, in which the objectives are to minimize total costs and transportation pollution. Both random and fuzzy uncertainties, for which return rate and disposal rate are considered fuzzy random variables, are jointly handled in this paper to ensure a more practical problem solution. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO is applied to ensure reliable solutions for this NP-hard problem. A beer company case study is given to illustrate the application of the proposed model and to demonstrate the priority-based global-local-neighbor particle swarm optimization.

  17. Standard guide for computed radiography

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 This guide provides general tutorial information regarding the fundamental and physical principles of computed radiography (CR), definitions and terminology required to understand the basic CR process. An introduction to some of the limitations that are typically encountered during the establishment of techniques and basic image processing methods are also provided. This guide does not provide specific techniques or acceptance criteria for specific end-user inspection applications. Information presented within this guide may be useful in conjunction with those standards of 1.2. 1.2 CR techniques for general inspection applications may be found in Practice E2033. Technical qualification attributes for CR systems may be found in Practice E2445. Criteria for classification of CR system technical performance levels may be found in Practice E2446. Reference Images Standards E2422, E2660, and E2669 contain digital reference acceptance illustrations. 1.3 The values stated in SI units are to be regarded as the st...

  18. Proton Radiography at Los Alamos

    Energy Technology Data Exchange (ETDEWEB)

    Saunders, Alexander [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-28

    The proton radiography (pRad) facility at Los Alamos National Lab uses high energy protons to acquire multiple frame flash radiographic sequences at megahertz speeds: that is, it can make movies of the inside of explosions as they happen. The facility is primarily used to study the damage to and failure of metals subjected to the shock forces of high explosives as well as to study the detonation of the explosives themselves. Applications include improving our understanding of the underlying physical processes that drive the performance of the nuclear weapons in the United States stockpile and developing novel armor technologies in collaboration with the Army Research Lab. The principle and techniques of pRad will be described, and examples of some recent results will be shown.

  19. NASA as a Convener: Government, Academic and Industry Collaborations Through the NASA Human Health and Performance Center

    Science.gov (United States)

    Davis, Jeffrey R.; Richard, Elizabeth E.

    2011-01-01

    On October 18, 2010, the NASA Human Health and Performance center (NHHPC) was opened to enable collaboration among government, academic and industry members. Membership rapidly grew to 60 members (http://nhhpc.nasa.gov ) and members began identifying collaborative projects as detailed below. In addition, a first workshop in open collaboration and innovation was conducted on January 19, 2011 by the NHHPC resulting in additional challenges and projects for further development. This first workshop was a result of the SLSD successes in running open innovation challenges over the past two years. In 2008, the NASA Johnson Space Center, Space Life Sciences Directorate (SLSD) began pilot projects in open innovation (crowd sourcing) to determine if these new internet-based platforms could indeed find solutions to difficult technical problems. From 2008 to 2010, the SLSD issued 34 challenges, 14 externally and 20 internally. The 14 external challenges were conducted through three different vendors: InnoCentive, Yet2.com and TopCoder. The 20 internal challenges were conducted using the InnoCentive platform, customized to NASA use, and promoted as NASA@Work. The results from the 34 challenges involved not only technical solutions that were reported previously at the 61st IAC, but also the formation of new collaborative relationships. For example, the TopCoder pilot was expanded by the NASA Space Operations Mission Directorate to the NASA Tournament Lab in collaboration with Harvard Business School and TopCoder. Building on these initial successes, the NHHPC workshop in January of 2011, and ongoing NHHPC member discussions, several important collaborations are in development: Space Act Agreement between NASA and GE for collaborative projects, NASA and academia for a Visual Impairment / Intracranial Hypertension summit (February 2011), NASA and the DoD through the Defense Venture Catalyst Initiative (DeVenCI) for a technical needs workshop (June 2011), NASA and the San Diego Zoo

  20. Collaborative Innovation of Pharmaceutical Industry for Improving the Function of Education Industry Management Center%医药协同创新中教育产业管理中心功能完善策略分析

    Institute of Scientific and Technical Information of China (English)

    张天骄

    2016-01-01

    Objective To promote the central role of education industry management center in the collaborative innovation of pharmaceu-tical industry. Methods The functions and responsibilities of the education industry management center was analyzed,its low positioning and imperfect function in the current social environment were revealed. Results and Conclusion Propose some measures in the context of the pharmaceutical industry about how to improve the education industry management center's function and how to promote the col-laborative innovation of Politic-Industry-Research.%目的:促进教育产业管理中心在医药协同创新中更好地发挥作用。方法分析教育产业管理中心的现有功能和职责,揭示其现状。结果与结论以医药产业为背景,提出了完善教育产业管理中心的功能及促进医药“政产学研”协同创新的相应措施。

  1. Estimation of patient exposure in dental radiography

    Energy Technology Data Exchange (ETDEWEB)

    Yasaki, Shiro; Yukishita, Kentaro; Daibo, Motoji; Suzuki, Yousuke [Ohu Univ., Koriyama, Fukushima (Japan). School of Dentistry

    1998-12-01

    Purpose of this study is to examine comparison of absorbed dose in each mode of newest Multimode Panoramic Radiography and Dental Radiography. The absorbed dose of Dental Radiography uses modified IWAI`s data. The effective doses were calculated using modified tissue weighting factors recommended by International Commission on Radiological Protection (ICRP) in 1990. The result of estimate in effective dose, panoramic auto function mode (4.92 {mu}Sv) was lower than dental full mouth (43.12 {mu}Sv). And clinical effective dose was higher than the other`s modes, in linear tomogram modes. The absorbed dose of patient in Dental Radiography is decreasing in recent years. But in daily clinical work we should pay atteation to justification and optimization. (author)

  2. Imaging beamline for high energy proton radiography

    Institute of Scientific and Technical Information of China (English)

    WEI Tao; YANG Guo-Jun; LONG Ji-Dong; WANG Shao-Heng; HE Xiao-Zhong

    2012-01-01

    Proton radiography is a new tool for advanced hydrotesting.This article will discuss the basic concept of proton radiography first,especially the magnetic lens system.Then a scenario of 50 GeV imaging beamline will be described in every particular,including the matching section,Zumbro lens system and imaging system.The simulation result shows that the scenario of imaging beamline performs well,and the influence of secondary particles can be neglected.

  3. Simulation of proton radiography terminal at IMP

    CERN Document Server

    Yan, Yan; Huang, Zhi-Wu; Wang, Jie; Yao, Ze-En; Wang, Jun-Run; Wei, Zheng; Yang, Jian-Cheng; Yuan, You-Jin

    2015-01-01

    Proton radiography is used for advanced hydrotesting as a new type radiography technology due to its powerful penetration capability and high detection efficiency. A new proton radiography terminal will be developed to radiograph static samples at Institute of Modern Physics of Chinese Academy of Science (IMP-CAS). The proton beam with the maximum energy of 2.6 GeV will be produced by Heavy Ion Research Facility in Lanzhou-Cooling Storage Ring (HIRFL-CSR). The proton radiography terminal consists of the matching magnetic lens and the Zumbro lens system. In this paper, the design scheme and all optic parameters of this beam terminal for 2.6GeV proton energy are presented by simulating the beam optics using WINAGILE code. My-BOC code is used to test the particle tracking of proton radiography beam line. Geant4 code and G4beamline code are used for simulating the proton radiography system. The results show that the transmission efficiency of proton without target is 100%, and the effect of secondary particles ca...

  4. Productivity improvements with a direct digital radiography system integrated with PACS

    Science.gov (United States)

    Jeromin, Lothar S.; Lee, Denny L. Y.; Palecki, Eugene F.; Wolff, David P.

    1996-05-01

    The productivity-improving features of a direct digital radiography system for projection radiography are introduced and the integration of the system with PACS is discussed. A flat panel digital array, an array controller, and a system controller with video monitor and standard interface to a local or wide area communications network are the main components of the direct digital radiography system of which prototypes have been built and tested in laboratory settings. When used in radiology room for projection radiography, the digital array converts x-ray photons into digital image data and makes the data available immediately for display on a video monitor for the technologist's review. Upon the technologist's acceptance of the image, an industry-standard network allows the transmission of the image to a workstation where additional image processing can be performed and where the image can be viewed on a high resolution display by the radiologist. If so desired, the image may be routed to a laser printer, digital mass storage medium, or to a PACS communication interface. By connecting the direct digital radiography system with a PACS network, radiographs may be shared electronically like images of other digital modalities. In this scenario, productivity improvements would come mainly from shorter patient exams as a result of the immediate availability of the review images, wider exposure latitude and ease of handling of the digital array, and from the electronic transport, storage and retrieval of image files and patient data in a PACS environment.

  5. Textile industry in Brno: A case study of cultural heritage and the memory of an industrial center (KULTURNÍ DĚDICTVÍ A PAMĚŤ INDUSTRIÁLNÍHO CENTRA (PŘÍPAD TEXTILNÍHO BRNA

    Directory of Open Access Journals (Sweden)

    Aleš Vyskočil

    2017-03-01

    Full Text Available This paper discusses industrial heritage, i.e. the society‘s relationship with the rem-nants of defunct industrial infrastructure. We demonstrate the issues involved on the example of Brno, one of the key economic centers of the Czech lands. Brno owes this status to its early industrialization, especially the textile industry which dominated its economic landscape from the late 1700s. Early 1990s saw the total collapse of the industry which resulted, inter alia, in the city‘s landscape being dotted by abandoned, defunct and derelict industrial buildings and building complexes. Those are now viewed as impediments to city‘s development and the city is looking for new ways to utilize them. These effort have been somewhat successful, for example in revitalizing a number of brownfields, but a large-scale solutions is still a desidera-tum. As a result, a number of building with great historical and cultural value have been torn down, including the industrial site of Vlněna, one of the icons of the textile industry in Brno, which was demolished in 2016. A unique opportunity to preserve, transform and revitalize this unique complex of buildings with immense historical value was wasted and thus a significant part of the industrial identity of Brno was irrevocably lost.

  6. Current radiography and tomography applications at Necsa and an envisaged upgrade towards a proposed South African national centre for radiography and tomography (SANCRAT)

    Energy Technology Data Exchange (ETDEWEB)

    Radebe, M.J.; De Beer, F.C. [Necsa - South African Nuclear Energy Corporation Limited, P. O.Box 582, Pretoria, 0001 (South Africa)

    2008-07-01

    An upgrade of the current Radiography and Tomography Research facilities is envisaged to enhance the group's support for Necsa's mission to undertake and support nuclear research and utilize penetrating radiation for the benefit of mankind. It is envisage that the SANCRAT will host neutron-, X-ray- and gamma ray penetrating radiation imaging infrastructures that can be utilized by researchers from industry as well as post graduate students from higher educational institutions. Modelling for the upgrade to a multifunctional neutron radiography and tomography facility has been underway. Upgrade plans and implementation has also begun for a 250 kV X-ray radiography set-up, that will exist independent from the neutron facility. Future expansion entails catering for a micro-focus X-ray -, and gamma ray radiography and tomography facilities. The current facilities available consist of one infrastructure facility based on two sources of penetrating radiation, i.e. SAFARI-1 research nuclear reactor as thermal neutron source and a 100 kV X-ray generator. This facility, which hosts the only operational neutron tomography R and D facility in the Southern Hemisphere and in Africa, are being extensively utilized by post graduate students and industry. The facility sees application in a wide range of scientific and engineering disciplines, amongst which is nuclear, geosciences, palaeontology, civil, mechanical, chemical, etc. This paper focus on case studies engaged at the current radiography and tomography facilities over the past 2 years as well as describing the envisaged upgrade initiatives to a fully equipped national centre. (authors)

  7. Thorium-uranium fission radiography

    Science.gov (United States)

    Haines, E. L.; Weiss, J. R.; Burnett, D. S.; Woolum, D. S.

    1976-01-01

    Results are described for studies designed to develop routine methods for in-situ measurement of the abundance of Th and U on a microscale in heterogeneous samples, especially rocks, using the secondary high-energy neutron flux developed when the 650 MeV proton beam of an accelerator is stopped in a 42 x 42 cm diam Cu cylinder. Irradiations were performed at three different locations in a rabbit tube in the beam stop area, and thick metal foils of Bi, Th, and natural U as well as polished silicate glasses of known U and Th contents were used as targets and were placed in contact with mica which served as a fission track detector. In many cases both bare and Cd-covered detectors were exposed. The exposed mica samples were etched in 48% HF and the fission tracks counted by conventional transmitted light microscopy. Relative fission cross sections are examined, along with absolute Th track production rates, interaction tracks, and a comparison of measured and calculated fission rates. The practicality of fast neutron radiography revealed by experiments to data is discussed primarily for Th/U measurements, and mixtures of other fissionable nuclei are briefly considered.

  8. Review and Prospect of Cobalt-60 Digital Radiography Inspection Technology

    Directory of Open Access Journals (Sweden)

    AN Ji-gang

    2015-11-01

    Full Text Available This article is a review and prospect of the research, development and industrialization of Cobalt-60 digital radiography inspection technology based on the national requirements in the recent 20 years, which is leaded by Institute of Nuclear and New Energy Technology (INET of TsinghuaUniversity. The research purpose, innovative approach and main academic achievements of this technology were described systematically. The industrial equipment varieties, performance, running condition and application effect were introduced, and the outstanding advantages and prospects of the technology are summarized. In the paper, some understanding obstacles or mistakes encountered during the promotion and application were sorted out and explained too to help the improvement and development of the new relevant technology.

  9. Digital Radiography Using Digital Detector Arrays Fulfills Critical Applications for Offshore Pipelines

    Directory of Open Access Journals (Sweden)

    Lopes RicardoTadeu

    2010-01-01

    Full Text Available Digital radiography in the inspection of welded pipes to be installed under deep water offshore gas and oil pipelines, like a presalt in Brazil, in the paper has been investigated. The aim is to use digital radiography for nondestructive testing of welds as it is already in use in the medical, aerospace, security, automotive, and petrochemical sectors. Among the current options, the DDA (Digital Detector Array is considered as one of the best solutions to replace industrial films, as well as to increase the sensitivity to reduce the inspection cycle time. This paper shows the results of this new technique, comparing it to radiography with industrial films systems. In this paper, 20 test specimens of longitudinal welded pipe joints, specially prepared with artificial defects like cracks, lack of fusion, lack of penetration, and porosities and slag inclusions with varying dimensions and in 06 different base metal wall thicknesses, were tested and a comparison of the techniques was made. These experiments verified the purposed rules for parameter definitions and selections to control the required digital radiographic image quality as described in the draft international standard ISO/DIS 10893-7. This draft is first standard establishing the parameters for digital radiography on weld seam of welded steel pipes for pressure purposes to be used on gas and oil pipelines.

  10. Muon radiography for exploration of Mars geology

    Directory of Open Access Journals (Sweden)

    S. Kedar

    2013-06-01

    Full Text Available Muon radiography is a technique that uses naturally occurring showers of muons (penetrating particles generated by cosmic rays to image the interior of large-scale geological structures in much the same way as standard X-ray radiography is used to image the interior of smaller objects. Recent developments and application of the technique to terrestrial volcanoes have demonstrated that a low-power, passive muon detector can peer deep into geological structures up to several kilometers in size, and provide crisp density profile images of their interior at ten meter scale resolution. Preliminary estimates of muon production on Mars indicate that the near horizontal Martian muon flux, which could be used for muon radiography, is as strong or stronger than that on Earth, making the technique suitable for exploration of numerous high priority geological targets on Mars. The high spatial resolution of muon radiography also makes the technique particularly suited for the discovery and delineation of Martian caverns, the most likely planetary environment for biological activity. As a passive imaging technique, muon radiography uses the perpetually present background cosmic ray radiation as the energy source for probing the interior of structures from the surface of the planet. The passive nature of the measurements provides an opportunity for a low power and low data rate instrument for planetary exploration that could operate as a scientifically valuable primary or secondary instrument in a variety of settings, with minimal impact on the mission's other instruments and operation.

  11. Muon radiography for exploration of Mars geology

    Directory of Open Access Journals (Sweden)

    S. Kedar

    2012-10-01

    Full Text Available Muon radiography is a technique that uses naturally occurring showers of muons (penetrating particles generated by cosmic rays to image the interior of large scale geological structures in much the same way as standard X-ray radiography is used to image the interior of smaller objects. Recent developments and application of the technique to terrestrial volcanoes have demonstrated that a low-power, passive muon detector can peer deep into geological structures up to several kilometers in size, and provide crisp density profile images of their interior at ten meter scale resolution. Preliminary estimates of muon production on Mars indicate that the near horizontal Martian muon flux, which could be used for muon radiography, is as strong or stronger than that on Earth, making the technique suitable for exploration of numerous high priority geological targets on Mars. The high spatial resolution of muon radiography also makes the technique particularly suited for the discovery and delineation of Martian caverns, the most likely planetary environment for biological activity. As a passive imaging technique, muon radiography uses the perpetually present background cosmic ray radiation as the energy source for probing the interior of structures from the surface of the planet. The passive nature of the measurements provides an opportunity for a low power and low data rate instrument for planetary exploration that could operate as a scientifically valuable primary or secondary instrument in a variety of settings, with minimal impact on the mission's other instruments and operation.

  12. Thyroid dose distribution in dental radiography

    Energy Technology Data Exchange (ETDEWEB)

    Bristow, R.G.; Wood, R.E.; Clark, G.M. (Ontario Cancer Institute, Toronto (Canada))

    1989-10-01

    The anatomic position and proven radiosensitivity of the thyroid gland make it an organ of concern in dental radiography. A calibrated thermoluminescent dosimetry system was used to investigate the absorbed dose (microGy) to the thyroid gland resultant from a minimum irradiated volume, intraoral full-mouth radiography technique with the use of rectangular collimation with a lead-backed image receptor, and conventional panoramic radiography performed with front and rear lead aprons. Use of the minimum irradiated volume technique resulted in a significantly decreased absorbed dose over the entire thyroid region ranging from 100% to 350% (p less than 0.05). Because this intraoral technique results in radiographs with greater image quality and also exposes the thyroid gland to less radiation than the panoramic, this technique may be an alternative to the panoramic procedure.

  13. Toward practical 3D radiography of pipeline girth welds

    Energy Technology Data Exchange (ETDEWEB)

    Wassink, Casper, E-mail: casper.wassink@applusrtd.com [Applus RTD Chief Scientist, Rivium 1e straat 80, 2909 LE Capelle a/d IJssel (Netherlands); Hol, Martijn, E-mail: martijn.hol@applusrtd.com; Flikweert, Arjan, E-mail: martijn.hol@applusrtd.com; Meer, Philip van, E-mail: martijn.hol@applusrtd.com [Applus RTD Technological Center, Delftweg 144, 3046 NC Rotterdam (Netherlands)

    2015-03-31

    Digital radiography has made its way into in-the-field girth weld testing. With recent generations of detectors and x-ray tubes it is possible to reach the image quality desired in standards as well as the speed of inspection desired to be competitive with film radiography and automated ultrasonic testing. This paper will show the application of these technologies in the RTD Rayscan system. The method for achieving an image quality that complies with or even exceeds prevailing industrial standards will be presented, as well as the application on pipeline girth welds with CRA layers. A next step in development will be to also achieve a measurement of weld flaw height to allow for performing an Engineering Critical Assessment on the weld. This will allow for similar acceptance limits as currently used with Automated Ultrasonic Testing of pipeline girth welds. Although a sufficient sizing accuracy was already demonstrated and qualified in the TomoCAR system, testing in some applications is restricted to time limits. The paper will present some experiments that were performed to achieve flaw height approximation within these time limits.

  14. Shallow Discuss on the Industry Position of Transportation Datum Center%浅谈交通运输数据中心的行业定位

    Institute of Scientific and Technical Information of China (English)

    马继军

    2014-01-01

    通过研究数据中心在青海省交通行业信息化中的行业地位,明确数据中心是青海交通运输信息化发展核心,而只有明确行业定位,才能为后续数据中心运行,乃至整个信息化发展思路提供纲领性要求。行业定位的不同级别,将对数据中心赋予不同的职责和功能。%By studying the industry position of datum center in Qinghai transportation informatization and make the datum center be develop core .Only explicit industry position can work for the datum center and pro‐vide programmatic requirements for entire informatization development ideas .The different levels of industry position confer the datum center be of different duty and functions .

  15. Digital radiography: a survey of pediatric dentists.

    Science.gov (United States)

    Russo, Julie M; Russo, James A; Guelmann, Marcio

    2006-01-01

    The purpose of this study was to: (1) determine the popularity of digital radiography among members of the American Academy of Pediatric Dentistry (AAPD); and (2) report the most common systems in use. An AAPD-approved, voluntary, and anonymous electronic survey was developed and sent to 923 board certified pediatric dentists. Years in practice and in-office x-ray technology (digital or conventional) were inquired about initially. If negative for the use of digital radiography, future consideration for converting to digital radiography was ascertained. For positive responses, more in-depth information was requested. Information on type of system (sensor or phosphor plate), user friendliness, diagnostic ability, patient's comfort, general costs, durability, and parental and overall satisfaction was collected. For most of the questions, a 5-point assessment scale was used. Opportunity for additional comments was provided upon survey completion. Data was analyzed using descriptive statistics. A 32% (296/923) response rate was obtained. Twenty-six percent of practitioners (78/296) implemented digital radiography in their practices, whereas 71% considered future acquisition. Similar distribution for sensor and phosphor plate users was found. Sensor technology was reported to produce faster images, but was less tolerable by young children due to size and thickness. Phosphor plates were considered more children friendly, less expensive, and less durable. Parental satisfaction was very high with great marketing value. Picture quality was comparable to conventional film. Overall, digital radiography users would recommend it to other pediatric dentists. Digital radiography is not yet popular among pediatric dentists. Cost reduction and technology advancement may enhance utilization.

  16. Proton Radiography: Its uses and Resolution Scaling

    Energy Technology Data Exchange (ETDEWEB)

    Mariam, Fesseha G. [Los Alamos National Laboratory

    2012-08-09

    Los Alamos National Laboratory has used high energy protons as a probe in flash radiography for over a decade. In this time the proton radiography project has used 800 MeV protons, provided by the LANSCE accelerator facility at LANL, to diagnose over five-hundred dynamic experiments in support of stockpile stewardship programs as well as basic materials science. Through this effort significant experience has been gained in using charged particles as direct radiographic probes to diagnose transient systems. The results of this experience will be discussed through the presentation of data from experiments recently performed at the LANL pRad.

  17. Statistical Uncertainty in Quantitative Neutron Radiography

    CERN Document Server

    Piegsa, Florian M

    2016-01-01

    We demonstrate a novel procedure to calibrate neutron detection systems commonly used in standard neutron radiography. This calibration allows determining the uncertainties due to Poisson-like neutron counting statistics for each individual pixel of a radiographic image. The obtained statistical errors are necessary in order to perform correct quantitative analysis. This fast and convenient method is applied to real data measured at the cold neutron radiography facility ICON at the Paul Scherrer Institute. Moreover, from the results the effective neutron flux at the beam line is determined.

  18. Bone X-Ray (Radiography)

    Medline Plus

    Full Text Available ... any possibility you are pregnant. Leave jewelry at home and wear loose, comfortable clothing. You may be ... emergency rooms, physician offices, ambulatory care centers, nursing homes and other locations, making it convenient for both ...

  19. Bone X-Ray (Radiography)

    Medline Plus

    Full Text Available ... offices, ambulatory care centers, nursing homes and other locations, making it convenient for both patients and physicians. ... Please note RadiologyInfo.org is not a medical facility. Please contact your physician with specific medical questions ...

  20. Bone X-Ray (Radiography)

    Medline Plus

    Full Text Available ... in emergency rooms, physician offices, ambulatory care centers, nursing homes and other locations, making it convenient for ... Safety page for more information about radiation dose. Women should always inform their physician or x-ray ...

  1. Bone X-Ray (Radiography)

    Medline Plus

    Full Text Available ... in emergency rooms, physician offices, ambulatory care centers, nursing homes and other locations, making it convenient for ... have special pediatric considerations. The teddy bear denotes child-specific content. Related Articles and Media Arthritis X- ...

  2. External validation of the New Orleans Criteria (NOC), the Canadian CT Head Rule (CCHR) and the National Emergency X-Radiography Utilization Study II (NEXUS II) for CT scanning in pediatric patients with minor head injury in a non-trauma center

    Energy Technology Data Exchange (ETDEWEB)

    Schachar, Jennifer L. [Albert Einstein College of Medicine, Department of Radiology, Bronx, NY (United States); Zampolin, Richard L.; Miller, Todd S.; Farinhas, Joaquim M.; Taragin, Benjamin H. [Albert Einstein College of Medicine and Montefiore Medical Center, Department of Radiology, Bronx, NY (United States); Freeman, Katherine [Albert Einstein College of Medicine and Montefiore Medical Center, Department of Biostatistics, Bronx, NY (United States)

    2011-08-15

    Head CT scans are considered the imaging modality of choice to screen patients with head trauma for neurocranial injuries; however, widespread CT imaging is not recommended and much research has been conducted to establish objective clinical predictors of intracranial injury (ICI) in order to optimize the use of neuroimaging in children with minor head trauma. To evaluate whether a strict application of the New Orleans Criteria (NOC), Canadian CT Head Rule (CCHR) and National Emergency X-Radiography Utilization Study II (NEXUS II) in pediatric patients with head trauma presenting to a non-trauma center (level II) could reduce the number of cranial CT scans performed without missing clinically significant ICI. We conducted an IRB-approved retrospective analysis of pediatric patients with head trauma who received a cranial CT scan between Jan. 1, 2001, and Sept. 1, 2008, and identified which patients would have required a scan based on the criteria of the above listed decision instruments. We then determined the sensitivities, specificities and negative predictive values of these aids. In our cohort of 2,101 patients, 92 (4.4%) had positive head CT findings. The sensitivities for the NOC, CCHR and NEXUS II were 96.7% (95%CI 93.1-100), 65.2% (95%CI 55.5-74.9) and 78.3% (95%CI 69.9-86.7), respectively, and their negative predictive values were 98.7%, 97.6% and 97.2%, respectively. In contrast, the specificities for these aids were 11.2% (95%CI 9.8-12.6), 64.2% (95%CI 62.1-66.3) and 34.2% (95%CI 32.1-36.3), respectively. Therefore, in our population it would have been possible to scan at least 10.9% fewer patients. The number of cranial CT scans conducted in our pediatric cohort with head trauma would have been reduced had any of the three clinical decision aids been applied. Therefore, we recommend that further validation and adoption of pediatric head CT decision aids in non-trauma centers be considered to ultimately increase patient safety while reducing medical

  3. EFFECTS OF TERRORISM IN TOURISM INDUSTRY : A Case Study of 9/11 Terrorist Attacks in World Trade Center

    OpenAIRE

    Ranabhat , Krishna

    2015-01-01

    Rapid growth of tourism industry has been a good sign of business. International tourism is co-operation between countries. The development of global economy is depending upon the global tourism industry. Social network is directly and indirectly affected by terrorism activities. There are push and pull factor in tourism. Terrorism is a pull factor that is considered a negative factor. Terrorism is the biggest factor, which pushes tourism industry down. Terrorism brings fear to tourists, whic...

  4. Low material budget floating strip Micromegas for ion transmission radiography

    Science.gov (United States)

    Bortfeldt, J.; Biebel, O.; Flierl, B.; Hertenberger, R.; Klitzner, F.; Lösel, Ph.; Magallanes, L.; Müller, R.; Parodi, K.; Schlüter, T.; Voss, B.; Zibell, A.

    2017-02-01

    Floating strip Micromegas are high-accuracy and discharge insensitive gaseous detectors, able to track single particles at fluxes of 7 MHz/cm2 with 100 μm resolution. We developed low-material-budget detectors with one-dimensional strip readout, suitable for tracking at highest particle rates as encountered in medical ion transmission radiography or inner tracker applications. Recently we additionally developed Kapton-based floating strip Micromegas with two-dimensional strip readout, featuring an overall thickness of 0.011 X0. These detectors were tested in high-rate proton and carbon-ion beams at the tandem accelerator in Garching and the Heidelberg Ion-Beam Therapy Center, operated with an optimized Ne:CF4 gas mixture. By coupling the Micromegas detectors to a new scintillator based range detector, ion transmission radiographies of PMMA and tissue-equivalent phantoms were acquired. The range detector with 18 layers is read out via wavelength shifting fibers, coupled to a multi-anode photomultiplier. We present the performance of the Micromegas detectors with respect to timing and single plane track reconstruction using the μTPC method. We discuss the range resolution of the scintillator range telescope and present the image reconstruction capabilities of the combined system.

  5. Feline dental radiography and radiology: A primer.

    Science.gov (United States)

    Niemiec, Brook A

    2014-11-01

    Information crucial to the diagnosis and treatment of feline oral diseases can be ascertained using dental radiography and the inclusion of this technology has been shown to be the best way to improve a dental practice. Becoming familar with the techniques required for dental radiology and radiography can, therefore, be greatly beneficial. Novices to dental radiography may need some time to adjust and become comfortable with the techniques. If using dental radiographic film, the generally recommended 'E' or 'F' speeds may be frustrating at first, due to their more specific exposure and image development requirements. Although interpreting dental radiographs is similar to interpreting a standard bony radiograph, there are pathologic states that are unique to the oral cavity and several normal anatomic structures that may mimic pathologic changes. Determining which teeth have been imaged also requires a firm knowledge of oral anatomy as well as the architecture of dental films/digital systems. This article draws on a range of dental radiography and radiology resources, and the benefit of the author's own experience, to review the basics of taking and interpreting intraoral dental radiographs. A simplified method for positioning the tubehead is explained and classic examples of some common oral pathologies are provided. © ISFM and AAFP 2014.

  6. Establishing rigour in qualitative radiography research

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, F.J. [School of Healthcare Professions, University of Salford, Salford M6 6PU (United Kingdom)], E-mail: f.j.murphy@salford.ac.uk; Yielder, J. [Medical Imaging, School of Health Sciences, Unitec, Auckland (New Zealand)

    2010-02-15

    The vast majority of radiography research is subject to critique and evaluation from peers in order to justify the method and the outcome of the study. Within the quantitative domain, which the majority of medical imaging publications tend to fall into, there are prescribed methods for establishing scientific rigour and quality in order to critique a study. However, researchers within the qualitative paradigm, which is a developing area of radiography research, are often unclear about the most appropriate methods to measure the rigour (standards and quality) of a research study. This article considers the issues related to rigour, reliability and validity within qualitative research. The concepts of reliability and validity are briefly discussed within traditional positivism and then the attempts to use these terms as a measure of quality within qualitative research are explored. Alternative methods for research rigour in interpretive research (meanings and emotions) are suggested in order to compliment the existing radiography framework that exists for qualitative studies. The authors propose the use of an established model that is adapted to reflect the iterative process of qualitative research. Although a mechanistic approach to establishing rigour is rejected by many qualitative researchers, it is argued that a guide for novice researchers within a developing research base such as radiography is appropriate in order to establish the credibility and trustworthiness of a qualitative study.

  7. Radiography Student Participation in Professional Organizations.

    Science.gov (United States)

    Michael, Kimberly; Tran, Xuan; Keller, Shelby; Sayles, Harlan; Custer, Tanya

    2017-09-01

    To gather data on educational program requirements for student membership in a state or national professional society, organization, or association. A 10-question online survey about student involvement in professional societies was emailed to 616 directors of Joint Review Committee on Education in Radiologic Technology (JRCERT)-accredited radiography programs. A total of 219 responses were received, for a 36% response rate. Of these, 89 respondents (41%) answered that their programs require students to join a professional organization. The society respondents most often required (70%) was a state radiography society. Sixty respondents (68%) answered that students join a society at the beginning of the radiography program (from matriculation to 3 months in). Of programs requiring student membership in professional societies, 42 (49%) reported that their students attend the state or national society annual conference; however, participation in activities at the conferences and in the society throughout the year is lower than conference attendance. Some directors stated that although their programs' policies do not allow membership mandates, they encourage students to become members, primarily so that they can access webinars and other educational materials or information related to the profession. Survey data showed that most JRCERT-accredited radiography programs support but do not require student membership in professional organizations. The data reveal that more programs have added those requirements in recent years. Increased student participation could be realized if programs mandated membership and supported it financially. ©2017 American Society of Radiologic Technologists.

  8. Comprehensive Optimization Process of Paranasal Sinus Radiography

    Energy Technology Data Exchange (ETDEWEB)

    Saarakkala, S. (Dept. of Clinical Radiology, Kuopio Univ. Hospital, Kuopio (Finland)); Nironen, K.; Hermunen, H.; Aarnio, J.; Heikkinen, J.O. (Dept. of Radiology, Etel-Savo Hospital District, Mikkeli Central Hospital, Mikkeli (Finland))

    2009-04-15

    Background: The optimization of radiological examinations is important in order to reduce unnecessary patient radiation exposure. Purpose: To perform a comprehensive optimization process for paranasal sinus radiography at Mikkeli Central Hospital (Finland). Material and Methods: Patients with suspicion of acute sinusitis were imaged with a Kodak computed radiography (CR) system (n=20) and with a Philips digital radiography (DR) system (n=30) using focus-detector distances (FDDs) of 110 cm, 150 cm, or 200 cm. Patients' radiation exposure was determined in terms of entrance surface dose and dose-area product. Furthermore, an anatomical phantom was used for the estimation of point doses inside the head. Clinical image quality was evaluated by an experienced radiologist, and physical image quality was evaluated from the digital radiography phantom. Results: Patient doses were significantly lower and image quality better with the DR system compared to the CR system. The differences in patient dose and physical image quality were small with varying FDD. Clinical image quality of the DR system was lowest with FDD of 200 cm. Further, imaging with FDD of 150 cm was technically easier for the technologist to perform than with FDD of 110 cm. Conclusion: After optimization, it was recommended that the DR system with FDD of 150 cm should always be used at Mikkeli Central Hospital. We recommend this kind of comprehensive approach in all optimization processes of radiological examinations.

  9. Almetax and industrial technology total center Shigaraki ceramic industry technology test field in Shiga Prefecture; Arumetakkusu to Shiga-ken kogyo gijutsu sogo senta sigaraki yogyo gijutsu gijutsu shikenjo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    Almetax and industrial technology total center Shigaraki ceramic industry technology test field in Shiga Prefecture. Almetax of the aluminum building material and industrial technology total center Shigaraki ceramic industry technology test field in Shiga Prefecture developed the light thermal insulation foaming tile in the cooperation. This is a tile using the ash which arises by the renewal process of the aluminum. The aluminum ash was mixed with the feldspar of the Shigaraki-made, and it was burnt at the low temperature. In the lightness under the half of usual tile, it has the heat retaining property over 3 times. almetax was being planned a waste loss thermal insulation a stone two bird environmental consideration type goods begin to. The aluminum ash is mixed with the feldspar, and by the process burnt at 1200-1250 degrees C, it decomposes, the aluminum nitride in the ash foams. Therefore, the stoma which was homogeneously independent in burnt tile is possible. It is lightly easy to be handled, and it is a feature that the heat retaining property is high. There is the strength from the foaming concrete, and the water absorption rate is low. The aluminum reconstruction technique of almetax was made to fuse with the technology of the ceramic industry technology test field of the pottery lightening. almetax studies the cost reduction of the decontamination processing of the ash. It aims at cost of product of 3 thousand yen /m{sup 2} of usual tile level. The commercialization as partition between two rooms of external wall and life space of the building has been planned. The gross discharge of the domestic aluminum ash has been estimated with annual about 192 thousand tons. Though the part is utilized as a secondary material of the iron and steel refining, it deals with the excess minute as an industrial waste. (translated by NEDO)

  10. Real time radiography generating three dimensional tomography; Radiografia em tempo real gerando tomografia tridimensional

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Luis Fernando de; Lopes, Ricardo Tadeu; Jesus, Edgar Francisco Oliveira de; Braz, Delson [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Lab. de Instrumentacao Nuclear

    2000-07-01

    This paper presents the development of a three dimensional tomography system based on a system of real time radiography. The system uses an microfocus X-ray tube with 10 {mu}m focus size, maximum 160 kV{sub p} voltage and 1 mA current, normally used in on-line inspection. Also is presented the determination of the basic parameters of image quality and of the system, and sone applications in problems related with the industry.

  11. Towards Improved Industrial Relations of Employees in Ethiopian Agricultural Research Institute: The Case of Ambo Plant Protection Research Center, Ambo, Ethiopia

    Directory of Open Access Journals (Sweden)

    Gemechu Shale Ogato

    2015-08-01

    Full Text Available Industrial relations cover all such relationships that a business enterprise maintains with various sections of the society such as workers, state customers, and public who come into its contact. In other words, it is the study of the interactions among industry, its employees and the governments that oversee them. The general objective of the study is to assess the industrial relations of employees of Ambo Plant Protection Research Center (APPRC and propose strategic measures for its improvement. The study employed comprehensive data collection methods whereby both secondary and primary methods of data collection methods were employed to address the objectives of the study.  Data collected through structured questionnaire were analyzed with the help of simple descriptive statistics like frequencies and percentages and inferential statistics with the help of SPSS software (version 20.  Promoting good governance and democracy, creating favorable working environment for employees and environment of good will and mutual cooperation, responding to employees’ reported problems promptly and positively; provision of trainings to employees on strategic issues and solutions; and encouraging employees to use modern technologies like ICTs in service delivery are some of the strategic measures proposed to improve the industrial relations of employees of Ambo Plant Protection Research Center.

  12. MRI versus radiography of acromioclavicular joint dislocation.

    Science.gov (United States)

    Nemec, Ursula; Oberleitner, Gerhard; Nemec, Stefan F; Gruber, Michael; Weber, Michael; Czerny, Christian; Krestan, Christian R

    2011-10-01

    Acromioclavicular joint injuries are usually diagnosed by clinical and radiographic assessment with the Rockwood classification, which is crucial for treatment planning. In view of the implementation of MRI for visualization of the acromioclavicular joint, the purpose of this study was to describe the MRI findings of acromioclavicular joint dislocation in comparison with the radiographic findings. Forty-four patients with suspected unilateral acromioclavicular joint dislocation after acute trauma were enrolled in this prospective study. All patients underwent digital radiography and 1-T MRI with a surface phased-array coil. MRI included coronal proton density-weighted turbo spin-echo and coronal 3D T1-weighted fast field-echo water-selective sequences. The Rockwood classification was used to assess acromioclavicular joint injuries at radiography and MRI. An adapted Rockwood classification was used for MRI evaluation of the acromioclavicular joint ligaments. The classifications of acromioclavicular joint dislocations diagnosed with radiography and MRI were compared. Among 44 patients with Rockwood type I-IV injuries on radiographs, classification on radiographs and MR images was concordant in 23 (52.2%) patients. At MRI, the injury was reclassified to a less severe type in 16 (36.4%) patients and to a more severe type in five (11.4%) patients. Compared with the findings according to the original Rockwood system, with the adapted system that included MRI findings, additional ligamentous lesions were found in 11 (25%) patients. In a considerable number of patients, the MRI findings change the Rockwood type determined with radiography. In addition to clinical assessment and radiography, MRI may yield important findings on ligaments that may influence management.

  13. Center for Corporate Climate Leadership: Direct Fugitive Emissions from Refrigeration, Air Conditioning, Fire Suppression, and Industrial Gases

    Science.gov (United States)

    This guidance document focuses on several fugitive emissions sources that are common for organizations in many sectors: refrigeration and air conditioningsystems, fire suppression systems, and the purchase and release of industrial gases.

  14. The scrounge-atron: a proton radiography demonstration accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Alford, O J; Barnes, P D; Chargin, A K; Hartouni, E F; Hockman, J N; Moore, T L; Pico, R E; Ruggiero, A G

    1998-12-18

    The Scrounge-atron is a concept that could provide a demonstration accelerator for proton radiography. As discussed here, the Scrounge-atron would be capable of providing a 20 GeV beam of ten pulses, 10{sup 11} protons each, spaced 250 ns apart. This beam could be delivered once every minute to a single-axis radiographic station centered at the BEEF facility of the Nevada Test Site. These parameters would be sufficient to demonstrate, in five years, the capabilities of a proton-based Advanced Hydrotest Facility, and could return valuable information to the stockpile program, information that could not be obtained in any other way. The Scrounge-atron could be built in two to three years for $50-100 million. To meet this schedule and cost, the Scrounge-atron would rely heavily on the availability of components from the decommissioned Fermilab Main Ring.

  15. Evaluation of ultrasound training in the problem based learning radiography curriculum at Makerere University, Uganda

    Energy Technology Data Exchange (ETDEWEB)

    Elsie, Kiguli-Malwadde [Makerere University, College of Health Sciences, Radiology Department, Kampala (Uganda); Gonzaga, Mubuuke A., E-mail: gmubuuke@gmail.co [Makerere University, College of Health Sciences, Radiology Department, Kampala (Uganda); Francis, Businge; Rebecca, Nakatudde; Stephen, Bule [Makerere University, College of Health Sciences, Radiology Department, Kampala (Uganda)

    2010-11-15

    Introduction: The College of Health Sciences (CHS), Makerere University has been training health professionals since 1924. Six years ago, there was a curriculum change to Problem Based Learning/Community based Education and Service (PBL/COBES). A SPICES model (Student centered, problem based, integrated, community based, electives, systematic) was adopted and defined to suit the CHS environment. The radiography program is 3 years in length which involves Ultrasound as an important part of the training. It was a challenge to adopt the new PBL method of learning after having a lecture-based pedagogical method for over 80 years. Objective: To implement the training of ultrasound in the PBL radiography curriculum as well as evaluate the opinions of the staff and students about Ultrasound training in the new curriculum. Methodology: A participatory approach was used. Workshops were conducted and objectives for ultrasound courses refined. Scenarios were written for use in the PBL sessions. A retrospective review of student performance in the ultrasound courses was carried out. A cross-sectional survey involving teachers and current radiography students was also carried out to evaluate learning of ultrasound using the PBL approach. Results: Students have consistently excelled in ultrasound courses using the PBL approach of learning. Both teachers and students rated the teaching of ultrasound to radiography students as being highly important and supported the new approach to training. Conclusion: Ultrasound training using PBL has been successfully implemented. However, this is still an ongoing process and will require the total commitment of both students and teachers.

  16. 10 CFR 34.13 - Specific license for industrial radiography.

    Science.gov (United States)

    2010-01-01

    ... submits a description of the applicant's overall organizational structure as it applies to the radiation... testing of sealed sources or exposure devices containing depleted uranium (DU) shielding, the applicant...

  17. Inspection of the metal composite materials using a combination of X-ray radiography and Neutron Imaging

    Energy Technology Data Exchange (ETDEWEB)

    Vavrik, D [Institute of Experimental and Applied Physics, Czech Technical University in Prague, Horska 3a/22, CZ 12800 Prague 2 (Czech Republic); Jeon, I [School of Mechanical Systems Engineering, Chonnam National University, Gwangju (Korea, Republic of); Lehmann, E; Kaestner, A [Paul Scherrer Institut, Neutron Imaging and Activation Group, WBBA/110 , CH-5232 Villigen PSI (Switzerland); Vacik, J, E-mail: vavrik@itam.cas.cz [Nuclear Physics Institute AS CR and Research Center Rez CZ-25068 (Czech Republic)

    2011-03-01

    Neutron Imaging and X-ray radiography are complementary methods from the point of view of the visibility and contrast of the material imaged. One potential application is the observation of the behavior of so-called 'metal composite materials', in which metallic and light material parts are combined. This material type is commonly used in the aerospace industry. Neutron Imaging is a suitable tool for the observation of the structure of light materials in an environment of heavier elements like metals. X-ray radiography on other hand is an appropriate tool for the observation of geometry of metal components inside an environment of lighter materials.

  18. Real-Time Neutron Radiography at CARR

    Institute of Scientific and Technical Information of China (English)

    HE; Lin-feng; HAN; Song-bai; WANG; Hong-li; WU; Mei-mei; WEI; Guo-hai; WANG; Yu

    2012-01-01

    <正>A real-time detector system for neutron radiography based on CMOS camera has been designed for the thermal neutron imaging facility under construction at China Advanced Research Reactor (CARR). This system is equipped with a new scientific CMOS camera with 5.5 million pixels and speed up to 100 fps at full frame. The readout noise is less than 2.4 electron per pixel. It is capable of providing

  19. Industry-wide studies report of an industrial-hygiene survey of Riverside Manor Nursing and Rehabilitation Center, Newcomerstown, Ohio. [Ethylene oxide exposures

    Energy Technology Data Exchange (ETDEWEB)

    Ringenburg, V.L.; Molina, D.; Elliott, L.J.

    1986-08-01

    Occupational exposure of workers to ethylene oxide (EtO) was examined. Two of six side-by-side short-term personal breathing-zone (BZ) exposure levels, determined while the sterilizer operator unloaded the EtO sterilizer unit, exceeded NIOSH recommended short term levels of 5 parts per million (ppm) for any 10-minute period per workday. Three of 12 personal BZ exposure levels exceeded the NIOSH recommended standard of less than 0.1ppm for an 8-hour time-weighted average. Measurable levels of EtO, ranging from 0.18 to 14.5ppm were detected in the storage room where the EtO sterilized items were aerated. The authors conclude that EtO exposure potential at the nursing and rehabilitation center could be reduced by improving administrative controls, work practices, and engineering controls. Recommended improvements were given.

  20. Draft Environmental Impact Report/Environmental Impact Statement, Proposed Marathon Industrial/Commercial Business Center Tract 5167, Hayward, California.

    Science.gov (United States)

    1985-10-01

    domestic water supplies; it now uses the Hetch Hetchy system. Therefore the groundwater aquifers are5 considered primarily as potential sources of City...water from the San Francisco Hetch Hetchy System. The City also maintains a well fieid in its industrial area as an emergency reserve. The nearest

  1. 77 FR 12852 - Draft Guidance for Industry on Limiting the Use of Certain Phthalates as Excipients in Center for...

    Science.gov (United States)

    2012-03-02

    ... for different functions in other dosage forms. Phthalates also are found in other products for uses... Phthalates as Excipients in CDER-Regulated Products.'' This draft guidance provides the pharmaceutical... (DEHP). In particular, the draft guidance recommends that the pharmaceutical industry avoid the use...

  2. Efficacy of panoramic radiography as a screening procedure in dental examination compared with clinical evaluation

    Energy Technology Data Exchange (ETDEWEB)

    An, Seo Young; An, Chang Hyeon; Choi, Karp Shik [Kyungpook National Univ. School of Dentistry, Daegu (Korea, Republic of)

    2007-06-15

    To evaluate the efficacy of panoramic radiography by comparing the results of clinical examination with radiographic findings. We studied 190 patients (20 men and 170 women; mean age, 40 years; range, 22 to 68 years) who visited the health promotion center of Korea Medical Science Institute and were examined both clinically and by panoramic radiography. We compared results from both examinations. Treatment options by clinical examination were described as 'no treatment indicated', 'treatment of dental caries', 'removal of calculus', 'treatment of periodontal disease'. 'prothodonic treatment' and 'extraction of the third molar'. Findings taken from the panoramic radiography were: dental caries, peroapical lesion, alveolar bone loss, calculus deposition, retained root, impaction of the third molar, disease of maxillary sinus, bony change of mandibular condyle, etc. The prevalence of panoramic findings were: 37.9% of dental caries, 17.4% of periapical lesions, 44.7% of alveolar bone losses, 62.6% of calculi deposition. 7.9% of retained roots, 26.8% of third molar impactions, 6.3% of disease of maxillary sinus, 2.1% of bony changes of mandibular condlye and 35.8% of miscellaneous lesions. Abnormal conditions revealed by panoramic radiography which had not been discovered on clinical examination were: 24.2% of the patients had dental caries, 17.4% had periapical lesions, 7.4% had calculi deposition, 5.3% had retained roots, 15.3% had third molar impactions. The opposite cases were: 5.2% had dental caries, 12.6% had calculi deposition, and 9.5% had third molar impactions. The use of panoramic radiography as a supplement to the clinical examination might be a valuable screening technique.

  3. Digital radiography: image quality and radiation dose.

    Science.gov (United States)

    Seibert, J Anthony

    2008-11-01

    Digital radiography devices, rapidly replacing analog screen-film detectors, are now common in diagnostic radiological imaging, where implementation has been accelerated by the commodity status of electronic imaging and display systems. The shift from narrow latitude, fixed-speed screen-film detectors to wide latitude, variable-speed digital detectors has created a flexible imaging system that can easily result in overexposures to the patient without the knowledge of the operator, thus potentially increasing the radiation burden of the patient population from radiographic examinations. In addition, image processing can be inappropriately applied causing inconsistent or artifactual appearance of anatomy, which can lead to misdiagnosis. On the other hand, many advantages can be obtained from the variable-speed digital detector, such as an ability to lower dose in many examinations, image post-processing for disease-specific conditions, display flexibility to change the appearance of the image and aid the physician in making a differential diagnosis, and easy access to digital images. An understanding of digital radiography is necessary to minimize the possibility of overexposures and inconsistent results, and to achieve the principle of as low as reasonably achievable (ALARA) for the safe and effective care of all patients. Thus many issues must be considered for optimal implementation of digital radiography, as reviewed in this article.

  4. Bacteriological research for the contamination of equipment in chest radiography

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Seung Gu; Song, Woon Heung; Kweon, Dae Cheol [Shinhan University, Uijeongbu (Korea, Republic of)

    2015-12-15

    The purpose is to determine the degree of contamination of the equipment for infection control in chest radiography of the radiology department. We confirmed by chemical and bacterial identification of bacteria of the equipment and established a preventive maintenance plan. Chest X-ray radiography contact area on the instrument patients shoulder, hand, chin, chest lateral radiography patient contact areas with a 70% isopropyl alcohol cotton swab were compared to identify the bacteria before and after sterilization on the patient contact area in the chest radiography equipment of the department. The gram positive Staphylococcus was isolated from side shoots handle before disinfection in the chest radiography equipment. For the final identification of antibiotic tested that it was determined by performing the nobobiocin to the sensitive Staphylococcus epidermidis. Chest radiography equipment before disinfecting the handle side of Staphylococcus epidermidis bacteria were detected using a disinfectant should be to prevent hospital infections.

  5. Development of neutron detectors and neutron radiography at Bhabha Atomic Research Centre

    Indian Academy of Sciences (India)

    A M Shaikh

    2008-10-01

    Design and development of neutron detectors and R&D work in neutron radiography (NR) for non-destructive evaluation are important parts of the neutron beam and allied research programme of Solid State Physics Division (SSPD) of Bhabha Atomic Research Centre (BARC). The detectors fabricated in the division not only meet the in-house requirement of neutron spectrometers but also the need of other divisions in BARC, Department of Atomic Energy units and some universities and research institutes in India and abroad for a variety of applications. The NR facility set up by SSPD at Apsara reactor has been used for a variety of applications in nuclear, aerospace, defense and metallurgical industries. The work done in the development of neutron detectors and neutron radiography is reported in this article.

  6. The Enhanced Workflow and Efficiency of the Wireless Local Area Network (WLAN)-Based Direct Digital Radiography (DDR) Portable Radiography.

    Science.gov (United States)

    Ngan, Tsz-Lung; Wong, Edward Ting-Hei; Ng, Kris Lap-Shun; Jeor, Patrick Kwok-Shing; Lo, Gladys Goh

    2015-06-01

    With the implementation of the PACS in the hospital, there is an increasing demand from the clinicians for immediate access and display of radiological images. Recently, our hospital has installed the first wireless local area network (WLAN)-based direct digital radiography (DDR) portable radiography system. The DDR portable radiography system allows wireless retrieval of modality worklist and wireless transmission of portable X-ray image on the console to the Picture Archiving and Communication System (PACS), via WLAN connection of wireless fidelity (Wi-Fi). The aim of this study was to analyze the workflow and performance between the WLAN-based DDR portable radiography system and the old practice using conventional portable X-ray machine with computed radiography (CR) system. A total of 190 portable chest X-ray examinations were evaluated and timed, using the conventional portable X-ray machine with CR from March to April of 2012 and using the new DDR portable radiography system on December of 2012 (n = 97 for old system and n = 93 for DDR portable system). The time interval of image becoming available to the PACS using the WLAN-based DDR portable radiography system was significantly shorter than that of the old practice using the conventional portable X-ray machine with CR (6.8 ± 2.6 min for DDR portable system; 23 ± 10.2 min for old system; p DDR portable radiography system can enhance the workflow of portable radiography by reduction of procedural steps.

  7. Control Systems Security Center Comparison Study of Industrial Control System Standards against the Control Systems Protection Framework Cyber-Security Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Robert P. Evans

    2005-09-01

    Cyber security standards, guidelines, and best practices for control systems are critical requirements that have been delineated and formally recognized by industry and government entities. Cyber security standards provide a common language within the industrial control system community, both national and international, to facilitate understanding of security awareness issues but, ultimately, they are intended to strengthen cyber security for control systems. This study and the preliminary findings outlined in this report are an initial attempt by the Control Systems Security Center (CSSC) Standard Awareness Team to better understand how existing and emerging industry standards, guidelines, and best practices address cyber security for industrial control systems. The Standard Awareness Team comprised subject matter experts in control systems and cyber security technologies and standards from several Department of Energy (DOE) National Laboratories, including Argonne National Laboratory, Idaho National Laboratory, Pacific Northwest National Laboratory, and Sandia National Laboratories. This study was conducted in two parts: a standard identification effort and a comparison analysis effort. During the standard identification effort, the Standard Awareness Team conducted a comprehensive open-source survey of existing control systems security standards, regulations, and guidelines in several of the critical infrastructure (CI) sectors, including the telecommunication, water, chemical, energy (electric power, petroleum and oil, natural gas), and transportation--rail sectors and sub-sectors. During the comparison analysis effort, the team compared the requirements contained in selected, identified, industry standards with the cyber security requirements in ''Cyber Security Protection Framework'', Version 0.9 (hereafter referred to as the ''Framework''). For each of the seven sector/sub-sectors listed above, one standard was

  8. Computed radiography in an emergency department setting

    Science.gov (United States)

    Andriole, Katherine P.; Gould, Robert G.; Arenson, Ronald L.

    1997-05-01

    Evaluation of radiologist and non-radiologist physician acceptance of computed radiography (CR) as an alternative to film-based radiography in an emergency department (ED) is performed. All emergency department radiographs are performed using photostimulable phosphor plates and rad by a computed radiography laser reader placed in the former emergency department darkroom. Soft copy images are simultaneously transmitted to high- and medium-resolution dual-monitor display stations located in radiology and ED reading rooms respectively. The on-call radiologist is automatically paged by the Radiology Information System (RIS) upon exam completion, to read the new ED imaging study. Patient demographic information including relevant clinical history is conveyed to the radiologist via the RIS. A 'wet read' preliminary radiology report is immediately transmitted back to the ED. Radiology and ED physicians are surveyed to ascertain preferences for CR or traditional screen-film, based on system implementation, image viewing and clinical impact issues. Preliminary results indicate a preference for filmless CR among the ED physicians if digital reliability and speed issues are met. This preference appears to be independent of physician level of experience. Inexperienced radiologists-in-training appear to have less comfort with softcopy reading for primary diagnosis. However, additional training in softcopy reading techniques can improve confidences. Image quality issues are most important tot he radiologist, while speed and reliability are the major issues for ED physicians. Reasons for CR preference include immediate access to images on display stations, near-zero exam retake rates, and improved response time and communication between radiology and the emergency department clinician.

  9. Industrial Communications.

    Science.gov (United States)

    Lindsay, Dan

    Intended for seniors planning a career in industry as skilled laborers, this specialized course in Industrial Communications offers the student basic communications skills which he will need in his work and in his daily life. Since class activities center around short, factual oral reports, class size will be limited to 20, providing a maximum of…

  10. Air conditioning and energy conservation. Improved space HVAC systems. Case studies: Office buildings, hotels, shopping centers, skyscrapers, industrial plants

    Energy Technology Data Exchange (ETDEWEB)

    Heiner, H.

    1988-08-01

    Rising energy prices and an increasing demand for comfortable rooms account for the importance attached to the windows and glass used for office buildings, hotels and industrial plants. Both windows and glass have a considerable influence on the thermal behavior and air conditioning of buildings. Among the latest developments are precious metal-coated insulating panes. Selected gases allow to reduce the total thickness of insulating glass and improve noise insulation. The case studies presented refer to the energy-saving air conditioning and space heating, heat recovery and cooling of rooms as well as to the respective control systems. Investigations into the specific energy consumption of building shells reveal the considerable space/tap water heating energy conservation potentials remaining to be utilized.

  11. Simulation of computed radiography with imaging plate detectors

    Energy Technology Data Exchange (ETDEWEB)

    Tisseur, D.; Costin, M. [CEA LIST, CEA Saclay 91191 Gif sur Yvette Cedex (France); Mathy, F. [CEA-LETI, Campus Minatec, F-38054, Grenoble (France); Schumm, A. [EDF R and D, 1 avenue du général de gaulle 92141 Clamart (France)

    2014-02-18

    Computed radiography (CR) using phosphor imaging plate detectors is taking an increasing place in Radiography Testing. CR uses similar equipment as conventional radiography except that the classical X-ray film is replaced by a numerical detector, called image plate (IP), which is made of a photostimulable layer and which is read by a scanning device through photostimulated luminescence. Such digital radiography has already demonstrated important benefits in terms of exposure time, decrease of source energies and thus reduction of radioprotection area besides being a solution without effluents. This paper presents a model for the simulation of radiography with image plate detectors in CIVA together with examples of validation of the model. The study consists in a cross comparison between experimental and simulation results obtained on a step wedge with a classical X-ray tube. Results are proposed in particular with wire Image quality Indicator (IQI) and duplex IQI.

  12. Digital radiography image quality: image processing and display.

    Science.gov (United States)

    Krupinski, Elizabeth A; Williams, Mark B; Andriole, Katherine; Strauss, Keith J; Applegate, Kimberly; Wyatt, Margaret; Bjork, Sandra; Seibert, J Anthony

    2007-06-01

    This article on digital radiography image processing and display is the second of two articles written as part of an intersociety effort to establish image quality standards for digital and computed radiography. The topic of the other paper is digital radiography image acquisition. The articles were developed collaboratively by the ACR, the American Association of Physicists in Medicine, and the Society for Imaging Informatics in Medicine. Increasingly, medical imaging and patient information are being managed using digital data during acquisition, transmission, storage, display, interpretation, and consultation. The management of data during each of these operations may have an impact on the quality of patient care. These articles describe what is known to improve image quality for digital and computed radiography and to make recommendations on optimal acquisition, processing, and display. The practice of digital radiography is a rapidly evolving technology that will require timely revision of any guidelines and standards.

  13. Nuclear track radiography of 'hot' aerosol particles

    CERN Document Server

    Boulyga, S F; Kievets, M K; Lomonosova, E M; Zhuk, I V; Yaroshevich, O I; Perelygin, V P; Petrova, R I; Brandt, R; Vater, P

    1999-01-01

    Nuclear track radiography was applied to identify aerosol 'hot' particles which contain elements of nuclear fuel and fallout after Chernobyl NPP accident. For the determination of the content of transuranium elements in radioactive aerosols the measurement of the alpha-activity of 'hot' particles by SSNTD was used in this work, as well as radiography of fission fragments formed as a result of the reactions (n,f) and (gamma,f) in the irradiation of aerosol filters by thermal neutrons and high energy gamma quanta. The technique allowed the sizes and alpha-activity of 'hot' particles to be determined without extracting them from the filter, as well as the determination of the uranium content and its enrichment by sup 2 sup 3 sup 5 U, sup 2 sup 3 sup 9 Pu and sup 2 sup 4 sup 1 Pu isotopes. Sensitivity of determination of alpha activity by fission method is 5x10 sup - sup 6 Bq per particle. The software for the system of image analysis was created. It ensured the identification of track clusters on an optical imag...

  14. Clinical Applications of Reverse Panoramic Radiography

    Directory of Open Access Journals (Sweden)

    Sujatha S Reddy

    2011-09-01

    Full Text Available The essence of oral and maxil-lofacial radiology is not only to be an important tool in the diagnostic assessment of dental patients but also to equip the clinician with the ability to interpret images of certain maxillocraniofacial structures of importance to dental, medical and surgical practices. Although combinations of several conven-tional x-ray projections can be adequate in a number of clinical situations, radiographic assessment of certain craniofacial structures some-times needs to be facilitated by other imaging modalities. A not-so-recent development called reverse panoramic radiography may be a useful adjuvant to such a situation, at least in the near future. It is essentially a technique where the patient is placed backwards in the panoramic machine in a reverse position in such a way that x-ray beam is directed through the patient’s face and the exit beam then passes through the patient’s head on the opposite side where it is captured on the receptor. The following manuscript is an attempt to throw light on this technique and the impact it may have on dental, medical and surgical practices. The advantages and disadvantages of reverse panoramic radiography and it’s comparison to conventional panoramic radiographs and other skull views are also dis-cussed.

  15. The Comparison between Two Different Digital Panoramic Radiography Techniques in the Detection of Proximal Caries

    Directory of Open Access Journals (Sweden)

    Hossein Hoseini Zarch

    2013-03-01

    Full Text Available Introduction: Although proximal dental caries are very common, clinical examinations cannot detect them all. Panoramic radiography has been widely used in dentistry for both diagnosis and screening. This study aimed to investigate and compare the efficacy of two digital panoramic radiography techniques in the diagnosis of proximal caries. Methods: A total number of 60 patients referred to a dental radiology center, all had complete dental system and bitewing radiographies, were included. The patients were randomly divided into two groups of 30 patients. For the first and second groups, CR and DR images were obtained respectively. Images were obtained from the distal of the third tooth to the distal of the eighth. Bitewing images were compared with CR and DR images regarding the detection of caries. Kappa index and chi-squared statistics were employed to analyze the results. Results: There was a high agreement rate between bitewing images and CR (Kappa=0.775 and DR (Kappa=o.762 images in detecting caries. Also no significant difference was shown between CR and DR techniques in the detection of caries (0.543. However, DR and CR images are not efficient enough to be prescribed as the sole imaging technique to detect proximal caries. Conclusion: DR and CR techniques could be good imaging techniques for the detection of dental caries as a companion to clinical examinations

  16. Comparison between Two Digital Panoramic Radiography Techniques for Proximal Caries Detection

    Directory of Open Access Journals (Sweden)

    Mina Shafagh Motlagh

    2013-03-01

    Full Text Available Introduction: Although proximal dental caries are very common, clinical examinations cannot detect them all. Panoramic radiography has been widely used in dentistry for both diagnosis and screening. This study aimed to investigate and compare the efficacy of two digital panoramic radiography techniques in the diagnosis of proximal caries. Methods: A total number of 60 patients referred to a dental radiology center, all had complete dental system and bitewing radiographies, were included. The patients were randomly divided into two groups of 30 patients. For the first and second groups, CR and DR images were obtained respectively. Images were obtained from the distal of the third tooth to the distal of the eighth. Bitewing images were compared with CR and DR images regarding the detection of caries. Kappa index and chi-squared statistics were employed to analyze the results. Results: There was a high agreement rate between bitewing images and CR (Kappa=0.775 and DR (Kappa=o.762 images in detecting caries. Also no significant difference was shown between CR and DR techniques in the detection of caries (0.543. However, DR and CR images are not efficient enough to be prescribed as the sole imaging technique to detect proximal caries. Conclusion: DR and CR techniques could be good imaging techniques for the detection of dental caries as a companion to clinical examinations.

  17. Comparative assessment of panoramic radiography and CBCT imaging for radiodiagnostics in the posterior maxilla.

    Science.gov (United States)

    Shahbazian, Maryam; Vandewoude, Charlotte; Wyatt, Jan; Jacobs, Reinhilde

    2014-01-01

    The purpose of this study was to assess whether and how the information obtained by means of cone beam computed tomography (CBCT) on maxillary posterior teeth differs from that obtained by panoramic radiography. From 157 subjects (mean age 48 years, range 19-84 years; 89 females) referred to the oral imaging center, a pair of panoramic and CBCT images was selected for further analysis. Both imaging modalities were analyzed to determine the topographic relationship of maxillary teeth to the sinus floor. Pathologic conditions, apical periodontitis, and presence of soft tissue thickening were also examined with both techniques. CBCT showed an intimate relationship of the first and second molar with the maxillary sinus in 54 and 38%, respectively. Thirty-nine apical periodontitis lesions causing reactive changes in the maxillary sinus were detected by CBCT, while just six of them were diagnosed with panoramic imaging. A total of 26 teeth with apical extension to the maxillary sinus were detected with CBCT, from which two could be identified with panoramic radiography. This study emphasizes that anatomical and pathological involvement of the maxillary sinus in relation to posterior teeth is considerably high. It is of clinical importance that the 3D nature of CBCT imaging allowed a better assessment of the relationship between the maxillary sinus and posterior root apices compared to the low detection on panoramic radiographs. CBCT imaging can be a valuable adjunct in radioanatomical and radiodiagnostic observations in the posterior maxilla. It may better visualize maxillary sinus involvement for posterior upper teeth than panoramic radiography.

  18. Control Systems Security Center Comparison Study of Industrial Control System Standards against the Control Systems Protection Framework Cyber-Security Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Robert P. Evans

    2005-09-01

    Cyber security standards, guidelines, and best practices for control systems are critical requirements that have been delineated and formally recognized by industry and government entities. Cyber security standards provide a common language within the industrial control system community, both national and international, to facilitate understanding of security awareness issues but, ultimately, they are intended to strengthen cyber security for control systems. This study and the preliminary findings outlined in this report are an initial attempt by the Control Systems Security Center (CSSC) Standard Awareness Team to better understand how existing and emerging industry standards, guidelines, and best practices address cyber security for industrial control systems. The Standard Awareness Team comprised subject matter experts in control systems and cyber security technologies and standards from several Department of Energy (DOE) National Laboratories, including Argonne National Laboratory, Idaho National Laboratory, Pacific Northwest National Laboratory, and Sandia National Laboratories. This study was conducted in two parts: a standard identification effort and a comparison analysis effort. During the standard identification effort, the Standard Awareness Team conducted a comprehensive open-source survey of existing control systems security standards, regulations, and guidelines in several of the critical infrastructure (CI) sectors, including the telecommunication, water, chemical, energy (electric power, petroleum and oil, natural gas), and transportation--rail sectors and sub-sectors. During the comparison analysis effort, the team compared the requirements contained in selected, identified, industry standards with the cyber security requirements in ''Cyber Security Protection Framework'', Version 0.9 (hereafter referred to as the ''Framework''). For each of the seven sector/sub-sectors listed above, one standard was

  19. Production System Analysis of Brem Processing Unit (Case Study: The Industrial Centers of Brem in Kaliabu and Bancong Village, Madiun District

    Directory of Open Access Journals (Sweden)

    Ardaneswari Dyah Pitaloka Citraresmi

    2014-10-01

    Full Text Available The purpose of this study was to determine the condition, the priorities, and the strategy development policy of the brem Madiun production system as an effort to increase the brem Madiun production system. The samples which are used were the brem industries at industrial centers of brem in Kaliabu and Bancong Village at Madiun District. The main instrument to collect the data was a questionnaire for 21 respondents of business leaders. Data analysis method which is used was Analytical Hierarchy Process (AHP. The results showed that the sequence of factors causing the decline of brem’s production capacity were the final product (0,477, capital (0,244, raw materials (0,123, human resources (0,088, the tools and machinery (0,041, and the method (0,026. Benchmarks for goals to be achieved by the production system were the effectiveness of brem Madiun (0,548, productivity (0,227, efficiency (0,138, and quality (0,087. Strategies that can be done on developing the brem industry in Madiun are provision of venture capital to support the administrations, improvement of licensing services, improvement of joint venture accessibility on infrastructure production, supporting on marketing, improvement of human resources quality (coaching and training, development of product, improvement of business management, and development on network of business partnership respectively. After the several strategies development policy was formulated based on existing condition, then the performance of the brem Madiun production system can be improved. Keywords : Brem, Production System Analysis, Strategy Formulation

  20. Assessment of a New Axis of Radiation in Hip Joint Radiographies

    Directory of Open Access Journals (Sweden)

    "A. Esmaeelzadeh

    2005-08-01

    Full Text Available Introduction & Background: The harmful effects of x-rays on sensitive cells such as those of sex gonads are a well-established fact. Therefore, special care should be taken in hip radiographies to protect the gonads. According to the most recent references, to locate the head of femur and its joint in hip radiographies, a line should be drawn from the ASIS to symphysis pubis. To locate the head of the joint, we had to move 2.5cm inferior and laterally from the middle of the men-tioned line. The outer end of this new line indicates the position of the femur head. However, due to the lack of accurate instruments in wards and the variety of diseases and also to avoid repetitive hip radiogra-phies, we decided to apply an experimental method. Patients & Methods: In this study, hip radiographies with FFD=100 were done for 50 patients of both sex with different ages. In all instances the distances be-tween symphysis pubis and the greater trocanter, the base of the lesser trocanter, and upper edge of acetabulum, and symphysis pubis and the center of femur, were measured on the radiographs by means of a standard ruler. The findings were then statisti-cally analyzed. The radiography apparatus was Phil-lips 500MA model D7. Results: In this study, it was shown that in 27 cases, the distance between symphysis pubis and the center of the head of femur was equal to the distance be-tween the base of the lesser trocanter and the upper edge of acetabulum. There was also a difference of 0.5, 1, and 2.5 centimeters in 14, 10, and 3 cases re-spectively. Conclusion: These findings were statistically signifi-cant and new. This is notable with regard to the ease of locating the hip joint in small radiographs. In addi-tion it has the advantage of a small degree of gonadal protection.

  1. Evaluation of entrance surface air kerma in pediatric chest radiography

    Science.gov (United States)

    Porto, L.; Lunelli, N.; Paschuk, S.; Oliveira, A.; Ferreira, J. L.; Schelin, H.; Miguel, C.; Denyak, V.; Kmiecik, C.; Tilly, J.; Khoury, H.

    2014-11-01

    The objective of this study was to evaluate the entrance surface air kerma in pediatric chest radiography. An evaluation of 301 radiographical examinations in anterior-posterior (AP) and posterior-anterior (PA) (166 examinations) and lateral (LAT) (135 examinations) projections was performed. The analyses were performed on patients grouped by age; the groups included ages 0-1 y, 1-5 y, 5-10 y, and 10-15 y. The entrance surface air kerma was determined with DoseCal software (Radiological Protection Center of Saint George's Hospital, London) and thermoluminescent dosimeters. Two different exposure techniques were compared. The doses received by patients who had undergone LAT examinations were 40% higher, on average, those in AP/PA examinations because of the difference in tube voltage. A large high-dose “tail” was observed for children up to 5 y old. An increase in tube potential and corresponding decrease in current lead to a significant dose reduction. The difference between the average dose values for different age ranges was not practically observed, implying that the exposure techniques are still not optimal. Exposure doses received using the higher tube voltage and lower current-time product correspond to the international diagnostic reference levels.

  2. Development of Automatic Remote Exposure Controller for Gamma Radiography

    Energy Technology Data Exchange (ETDEWEB)

    Joo, Gwang Tae; Shin, Jin Seong; Kim, Dong Eun; Song, Jung Ho; Choo, Seung Hwan; Chang, Hong Keun [Korea Industrial Testing Co., Ltd., Seoul (Korea, Republic of)

    2002-10-15

    Recently, gamma radiographic equipment have been used about 1,000 sets manually and operated by about 2,500 persons in Korea. In order for a radiography to work effectively with avoiding any hazard of the high level radiation from the source, many field workers have expected developing a wireless automatic remote exposure controller. The KlTCO research team has developed an automatic remote exposure controller that can regulate the speed of 0.4{approx}1.2m/s by BLDC motor of 24V 200W which has output of 54 kgf{center_dot}, suitable torque and safety factor for the work. And the developed automatic remote exposure controller can control rpm of motor, pigtail position by photo-sensor and exposure time by timer to RF sensor. Thus, the developed equipment is expected that the unit can be used in many practical applications with benefits in economical advantage to combine the use of both automatic and manual type because attachment is possible existent manual remote exposure controller, AC and DC combined use

  3. Performance evaluation of a computed radiography system

    Energy Technology Data Exchange (ETDEWEB)

    Roussilhe, J.; Fallet, E. [Carestream Health France, 71 - Chalon/Saone (France); Mango, St.A. [Carestream Health, Inc. Rochester, New York (United States)

    2007-07-01

    Computed radiography (CR) standards have been formalized and published in Europe and in the US. The CR system classification is defined in those standards by - minimum normalized signal-to-noise ratio (SNRN), and - maximum basic spatial resolution (SRb). Both the signal-to-noise ratio (SNR) and the contrast sensitivity of a CR system depend on the dose (exposure time and conditions) at the detector. Because of their wide dynamic range, the same storage phosphor imaging plate can qualify for all six CR system classes. The exposure characteristics from 30 to 450 kV, the contrast sensitivity, and the spatial resolution of the KODAK INDUSTREX CR Digital System have been thoroughly evaluated. This paper will present some of the factors that determine the system's spatial resolution performance. (authors)

  4. Digital radiography exposure indices: A review

    Energy Technology Data Exchange (ETDEWEB)

    Mothiram, Ursula; Brennan, Patrick C; Lewis, Sarah J [Medical Imaging Optimisation and Perception Group (MIOPeG), Discipline of Medical Radiation Sciences, Faculty of Health Science, University of Sydney, Sydney, New South Wales (Australia); Moran, Bernadette [Department of Clinical Medicine, Trinity College, Dublin (Ireland); Robinson, John [Medical Imaging Optimisation and Perception Group (MIOPeG), Discipline of Medical Radiation Sciences, Faculty of Health Science, University of Sydney, Sydney, New South Wales (Australia)

    2014-06-15

    Digital radiography (DR) technologies have the advantage of a wide dynamic range compared to their film-screen predecessors, however, this poses a potential for increased patient exposure if left unchecked. Manufacturers have developed the exposure index (EI) to counter this, which provides radiographers with feedback on the exposure reaching the detector. As these EIs were manufacturer-specific, a wide variety of EIs existed. To offset this, the international standardised EI has been developed by the International Electrotechnical Commission (IEC) and the American Association of Physicists in Medicine (AAPM). The purpose of this article is to explore the current literature relating to EIs, beginning with the historical development of the EI, the development of the standardised EI and an exploration of common themes and studies as evidenced in the research literature. It is anticipated that this review will provide radiographers with a useful guide to understanding EIs, their application in clinical practice, limitations and suggestions for further research.

  5. Machine learning applied to proton radiography

    CERN Document Server

    Chen, Nicholas Fang Yew; Ceurvorst, Luke; Ratan, Naren; Sadler, James; Levy, Matthew; Trines, Raoul; Bingham, Robert; Norreys, Peter

    2016-01-01

    Proton radiography is a technique extensively used to resolve magnetic field structures in high energy density plasmas, revealing a whole variety of interesting phenomena such as magnetic reconnection and collisionless shocks found in astrophysical systems. Existing methods of analyzing proton radiographs give mostly qualitative results or specific quantitative parameters such as magnetic field strength, and recent work showed that the line-integrated transverse magnetic field can be reconstructed in specific regimes where many simplifying assumptions were needed. Using artificial neural networks, we suggest a novel 3-D reconstruction method that works for a more general case. A proof of concept is presented here, with mean reconstruction errors of less than 5 percent even after introducing noise. We demonstrate that over the long term, this approach is more computationally efficient compared to other techniques. We also highlight the need for proton tomography because (i) certain field structures cannot be r...

  6. Oral history in radiography: Listening to pioneers

    Energy Technology Data Exchange (ETDEWEB)

    Ferris, Christine [International Development Facilitator, Robert Winston Building, Faculty of Health and Wellbeing, Sheffield Hallam University, Sheffield S10 2BP (United Kingdom)], E-mail: c.m.ferris@shu.ac.uk; Winslow, Michelle [University of Sheffield, Oral History Society, Academic Unit of Supportive Care, Sykes House, Little Common Lane, Sheffield S11 9NE (United Kingdom)], E-mail: m.winslow@sheffield.ac.uk

    2009-12-15

    We explore the professional value of the collection and analysis of oral histories in the history of radiography. Drawing on oral histories collected from radiographers, we analyse accounts of experiences to identify common themes, some of which are of current significance, whilst others have faded from existence. 15 oral histories were collected from radiographers whose combined practice spans the years 1930-1973. The sample consists of 6 male and 9 female radiographers. Themes identified in the oral histories include radiographers as invisible pioneers who worked in professionally unclaimed territory and their dangerous working environment. The oral histories reveal the working world of the radiographer as having encompassed a practice ethos where challenges became an accepted part of work. We gain insight into less observable aspects of the radiographer's role, the difficulties they faced, how they invented techniques and equipment, and how they managed their practice including protecting the public from ionising radiation sources.

  7. Polarized neutron radiography with a periscope

    Science.gov (United States)

    Schulz, Michael; Neubauer, Andreas; Mühlbauer, Martin; Calzada, Elbio; Schillinger, Burkhard; Pfleiderer, Christian; Böni, Peter

    2010-01-01

    The interaction of the magnetic moment of the neutron with magnetic fields provides a powerful probe for spatially resolved magnetisation measurements in magnetic materials. We have tested a periscope as a new type of polarizer providing neutron beams with a high polarization and a low divergence. The observed inhomogeneity of the beam caused by the waviness of the glass substrates was quantified by means of Monte-Carlo simulations using the software package McStas. The results show that beams of high homogeneity can be produced if the waviness is reduced to below 1.0·10-5 rad. Finally, it is shown that radiography with polarized neutrons is a powerful method for measuring the spatially resolved magnetisation in optically float-zoned samples of the weak itinerant ferromagnet Ni3Al, thereby aiding the identification of the appropriate growth parameters.

  8. Measuring microfocus focal spots using digital radiography

    Energy Technology Data Exchange (ETDEWEB)

    Fry, David A [Los Alamos National Laboratory

    2009-01-01

    Measurement of microfocus spot size can be important for several reasons: (1) Quality assurance during manufacture of microfocus tubes; (2) Tracking performance and stability of microfocus tubes; (3) Determining magnification (especially important for digital radiography where the native spatial resolution of the digital system is not adequate for the application); (4) Knowledge of unsharpness from the focal spot alone. The European Standard EN 12543-5 is based on a simple geometrical method of calculating focal spot size from unsharpness of high magnification film radiographs. When determining microfocus focal spot dimensions using unsharpness measurements both signal-to-noise (SNR) and magnification can be important. There is a maximum accuracy that is a function of SNR and therefore an optimal magnification. Greater than optimal magnification can be used but it will not increase accuracy.

  9. Vertex occlusal radiography in localizing unerupted mesiodentes

    Directory of Open Access Journals (Sweden)

    P Chalakkal

    2011-01-01

    Full Text Available The aim was to compare the vertex occlusal projection with the anterior maxillary occlusal projection in localizing the position of mesiodentes. Mesiodentes were observed in an 8-year-old boy with an anterior maxillary occlusal radiograph. A vertex occlusal radiograph was taken to compare it with the former in terms of mesiodentes localization with respect to the maxillary central incisors. The vertex occlusal radiograph provided greater details of the position and proximity of mesiodentes with respect to the long axis of maxillary central incisors in comparison to the anterior maxillary occlusal radiograph. Vertex occlusal radiography is an important diagnostic tool in diagnosing the presence, position, and proximity of mesiodentes with respect to the long axis of normally aligned maxillary central incisors. However, it is not recommended for routine use in a patient as its radiation dose is higher than conventional intraoral radiographic methods.

  10. Muscle parameters estimation based on biplanar radiography.

    Science.gov (United States)

    Dubois, G; Rouch, P; Bonneau, D; Gennisson, J L; Skalli, W

    2016-11-01

    The evaluation of muscle and joint forces in vivo is still a challenge. Musculo-Skeletal (musculo-skeletal) models are used to compute forces based on movement analysis. Most of them are built from a scaled-generic model based on cadaver measurements, which provides a low level of personalization, or from Magnetic Resonance Images, which provide a personalized model in lying position. This study proposed an original two steps method to access a subject-specific musculo-skeletal model in 30 min, which is based solely on biplanar X-Rays. First, the subject-specific 3D geometry of bones and skin envelopes were reconstructed from biplanar X-Rays radiography. Then, 2200 corresponding control points were identified between a reference model and the subject-specific X-Rays model. Finally, the shape of 21 lower limb muscles was estimated using a non-linear transformation between the control points in order to fit the muscle shape of the reference model to the X-Rays model. Twelfth musculo-skeletal models were reconstructed and compared to their reference. The muscle volume was not accurately estimated with a standard deviation (SD) ranging from 10 to 68%. However, this method provided an accurate estimation the muscle line of action with a SD of the length difference lower than 2% and a positioning error lower than 20 mm. The moment arm was also well estimated with SD lower than 15% for most muscle, which was significantly better than scaled-generic model for most muscle. This method open the way to a quick modeling method for gait analysis based on biplanar radiography.

  11. 200 MeV Proton Radiography Studies with a Hand Phantom Using a Prototype Proton CT Scanner

    Science.gov (United States)

    Plautz, Tia; Bashkirov, V.; Feng, V.; Hurley, F.; Johnson, R.P.; Leary, C.; Macafee, S.; Plumb, A.; Rykalin, V.; Sadrozinski, H.F.-W.; Schubert, K.; Schulte, R.; Schultze, B.; Steinberg, D.; Witt, M.; Zatserklyaniy, A.

    2014-01-01

    Proton radiography has applications in patient alignment and verification procedures for proton beam radiation therapy. In this paper, we report an experiment which used 200 MeV protons to generate proton energy-loss and scattering radiographs of a hand phantom. The experiment used the first-generation proton CT scanner prototype, which was installed on the research beam line of the clinical proton synchrotron at Loma Linda University Medical Center (LLUMC). It was found that while both radiographs displayed anatomical details of the hand phantom, the energy-loss radiograph had a noticeably higher resolution. Nonetheless, scattering radiography may yield more contrast between soft and bone tissue than energy-loss radiography, however, this requires further study. This study contributes to the optimization of the performance of the next-generation of clinical proton CT scanners. Furthermore, it demonstrates the potential of proton imaging (proton radiography and CT), which is now within reach of becoming available as a new, potentially low-dose medical imaging modality. PMID:24710156

  12. 200 MeV proton radiography studies with a hand phantom using a prototype proton CT scanner.

    Science.gov (United States)

    Plautz, Tia; Bashkirov, V; Feng, V; Hurley, F; Johnson, R P; Leary, C; Macafee, S; Plumb, A; Rykalin, V; Sadrozinski, H F-W; Schubert, K; Schulte, R; Schultze, B; Steinberg, D; Witt, M; Zatserklyaniy, A

    2014-04-01

    Proton radiography has applications in patient alignment and verification procedures for proton beam radiation therapy. In this paper, we report an experiment which used 200 MeV protons to generate proton energy-loss and scattering radiographs of a hand phantom. The experiment used the first-generation proton computed tomography (CT) scanner prototype, which was installed on the research beam line of the clinical proton synchrotron at Loma Linda University Medical Center. It was found that while both radiographs displayed anatomical details of the hand phantom, the energy-loss radiograph had a noticeably higher resolution. Nonetheless, scattering radiography may yield more contrast between soft and bone tissue than energy-loss radiography, however, this requires further study. This study contributes to the optimization of the performance of the next-generation of clinical proton CT scanners. Furthermore, it demonstrates the potential of proton imaging (proton radiography and CT), which is now within reach of becoming available as a new, potentially low-dose medical imaging modality.

  13. Characterization of film-converter screens systems for neutron radiography; Caracterizacao de sistemas filme-conversor para radiografia com neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Marcos Leandro Garcia

    2002-07-01

    In general a good quality radiography is that one able to furnish high contrast and sharp edge images. Technically 'high contrast' means high capability to discern material thickness and 'sharp edges', high resolution power. In the present work the optimal conditions to obtain neutron radiography images by using the following film-converter screen systems, Kodak-AA/Gd vaporated; Kodak-AA/Gd metallic; Kodak-AA/LiF; Min-R/GdS{sub 2}O{sub 4}, have been determined. The irradiations were performed in a radiographic facility which was designed and constructed by the neutron radiography working group and is installed at the beamhole 08 of the IEA-R1 nuclear research reactor of the IPEN-CNEN/SP. In order to determine such conditions, the start point was to evaluate the neutron exposure interval for which the optical contrast is maximal and so quantify the sensitivity or capability to discern material thickness, as well as the spatial resolution achieved in the radiographic image, for these systems. The best results have been obtained for the Kodak-AA/Gd vaporated system which is able to discern, for example, 0,024 cm of lucite, with a maximal resolution of 22{mu}m. The radiography images presently obtained in IPEN-CNEN/SP have similar quality when compared to the ones from several other research centers, around the world, whose making use of the same film-converter screens systems. (author)

  14. How to create a degree course in radiography: a recipe

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, S. E-mail: Pratt@cf.ac.uk; Adams, C. E-mail: AdamsC1@cf.ac.uk

    2003-11-01

    This article explains how an undergraduate programme is devised and validated. Since 1993, all courses in radiography have been of graduate level with radiography education being based in higher educational institutions. Before a new degree is implemented a review of the existing programme is undertaken. The proposed degree philosophy and learning outcomes need to be determined before the content; its mode of delivery and assessment are developed. Input from stakeholders (such as clinical colleagues) is necessary as well as adherence to policies and strategies for radiography education. Throughout the development process compliance with policy, both national and local, is critical. All radiography programmes have to be validated/accredited by representatives from national organisations--such as The Society and College of Radiographers (SCoR). These representatives scrutinise the proposed degree course documentation; often they may also inspect the clinical and university facilities in which the education and training will take place.

  15. Thickness-Independent Ultrasonic Imaging Applied to Abrasive Cut-Off Wheels: An Advanced Aerospace Materials Characterization Method for the Abrasives Industry. A NASA Lewis Research Center Technology Transfer Case History

    Science.gov (United States)

    Roth, Don J.; Farmer, Donald A.

    1998-01-01

    Abrasive cut-off wheels are at times unintentionally manufactured with nonuniformity that is difficult to identify and sufficiently characterize without time-consuming, destructive examination. One particular nonuniformity is a density variation condition occurring around the wheel circumference or along the radius, or both. This density variation, depending on its severity, can cause wheel warpage and wheel vibration resulting in unacceptable performance and perhaps premature failure of the wheel. Conventional nondestructive evaluation methods such as ultrasonic c-scan imaging and film radiography are inaccurate in their attempts at characterizing the density variation because a superimposing thickness variation exists as well in the wheel. In this article, the single transducer thickness-independent ultrasonic imaging method, developed specifically to allow more accurate characterization of aerospace components, is shown to precisely characterize the extent of the density variation in a cut-off wheel having a superimposing thickness variation. The method thereby has potential as an effective quality control tool in the abrasives industry for the wheel manufacturer.

  16. Interconnection of industrial centers with the electric network of the public service; Interconexion de centros industriales con la red electrica del servicio publico

    Energy Technology Data Exchange (ETDEWEB)

    Rosales Sedano, Inocente; Lopez Velazquez, Juan Jose; Garcia Paredes, Job; Robles Pimentel, Edgar [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico); Garcia Alvarez, David; Guzman Camacho, Benigno [Petroleos Mexicanos (Mexico)

    2000-07-01

    The large industrial centers that have continuous production processes and consume high amounts of electrical energy, generally have their own power generation. The petrochemical complexes, the paper and steel factories and the sugar mills are examples of this type of centers. On the other hand, the new regulation for the generation of electrical energy that allows to the electrical energy interchange between private companies and the public network, has originated the necessity of connecting systems that formerly operated isolated. Since the original design of the isolated electrical systems was to operate in an independent form, making the interconnection can generate technical problems that must be analyzed and solved. In this paper, some experiences related with the behavior of electrical equipment when connected to operate with the public network, are presented. [Spanish] Los grandes centros industriales que tienen procesos de produccion continua y consumen altas cantidades de energia electrica, generalmente cuentan con generacion propia. Los complejos petroquimicos, las fabricas de papel y acero y los ingenios azucareros son ejemplos de este tipo de centros. Por otro lado, la nueva reglamentacion de generacion de energia electrica que permite el intercambio de energia electrica entre las companias privadas y la red publica, ha originado la necesidad de conectar sistemas que antes operaban aislados. Debido a que el diseno original de los sistemas electricos aislados fue trabajar en forma independiente, el realizar la interconexion puede generar problemas tecnicos que tienen que analizarse y resolverse. En este articulo, se presentan algunas experiencias relacionadas con el comportamiento del equipo electrico al operar conectado con la red publica.

  17. The Discussion of the Industrial Engineering Training in Engineering Training Center%工程训练中心工业工程实训初探

    Institute of Scientific and Technical Information of China (English)

    荆琴; 申小平; 张巨香

    2013-01-01

      工业工程(IE)以其专业跨度大、实用性强、可有效设计和改善系统的优势,在各行各业得到了广泛应用。针对高校工业工程专业实验教学资源不足以及其他专业对工业工程了解甚少的问题,探讨了在工程训练中心进行工业工程实训的相关问题。%Industrial engineering (IE) is widely used in all walks of life, because it is associated with many professionals, has strong practica⁃bility and can effectively design or improve system's advantage. Based on the problem of the universities are all lack of IE experimental teaching resource and other professional students poorly understand IE, this paper probes into some problems of the IE training in engineer⁃ing training center.

  18. Efforts of the National Center for Optics and Photonics Education (OP-TEC) to prepare the technician workforce for photonics industries

    Science.gov (United States)

    Hull, Dan; Souders, John

    2009-06-01

    The mission of the National Center for Optics and Photonics Education (OP-TEC) is to create a secondary-to-postsecondary "pipeline" of highly qualified and strongly motivated students and to empower high schools and community colleges to meet the urgent need for technicians in optics and photonics. This paper describes the methodologies and processes OP-TEC has developed to carry out that mission. A recently completed assessment of the need for optics and photonics technicians in American industry concluded that U.S. colleges lack the capacity to produce an adequate supply. OP-TEC's challenge is to close the gap between the supply of and demand for photonics technicians. To help increase college capacity, OP-TEC has developed and implemented a recruitment process for initiating photonics programs in U.S. colleges. This paper describes the recruitment process and its results, along with the relevant support services provided by OP-TEC. In support of its mission, OP-TEC has developed curriculum and instructional materials that prepare students for the photonics workforce. To help ensure that completers of U.S. photonics programs are workforce ready, OP-TEC uses a skill-standards-based process for developing curriculum and instructional materials. This paper reviews the foundational skill standards and explains the process for integrating them into the materials development process. The curriculum and instructional materials that result from this process are also described.1

  19. PUBLIC SCHOOL LAWS OF NORTH CAROLINA--COMMUNITY COLLEGES, TECHNICAL INSTITUTES, AND INDUSTRIAL EDUCATION CENTERS. CHAPTER 115A, GENERAL STATUTES OF NORTH CAROLINA, INCLUDING AMENDMENTS ADOPTED BY THE 1965 AND 1967 GENERAL ASSEMBLIES.

    Science.gov (United States)

    North Carolina General Assembly, Raleigh.

    CHAPTER 115A OF THE GENERAL STATUTES OF NORTH CAROLINA PROVIDES FOR THE STATE'S COMMUNITY COLLEGES, TECHNICAL INSTITUTES, AND INDUSTRIAL EDUCATION CENTERS. IT INCLUDES THE FOLLOWING ARTICLES--(1) GENERAL PROVISIONS FOR STATE ADMINISTRATION, (2) LOCAL ADMINISTRATION, (3) FINANCIAL SUPPORT, (4) BUDGETING, ACCOUNTING, AND FISCAL MANAGEMENT, (5)…

  20. Beam Characterization at the Neutron Radiography Facility

    Energy Technology Data Exchange (ETDEWEB)

    Sarah Morgan; Jeffrey King

    2013-01-01

    The quality of a neutron imaging beam directly impacts the quality of radiographic images produced using that beam. Fully characterizing a neutron beam, including determination of the beam’s effective length-to-diameter ratio, neutron flux profile, energy spectrum, image quality, and beam divergence, is vital for producing quality radiographic images. This project characterized the east neutron imaging beamline at the Idaho National Laboratory Neutron Radiography Reactor (NRAD). The experiments which measured the beam’s effective length-to-diameter ratio and image quality are based on American Society for Testing and Materials (ASTM) standards. An analysis of the image produced by a calibrated phantom measured the beam divergence. The energy spectrum measurements consist of a series of foil irradiations using a selection of activation foils, compared to the results produced by a Monte Carlo n-Particle (MCNP) model of the beamline. Improvement of the existing NRAD MCNP beamline model includes validation of the model’s energy spectrum and the development of enhanced image simulation methods. The image simulation methods predict the radiographic image of an object based on the foil reaction rate data obtained by placing a model of the object in front of the image plane in an MCNP beamline model.

  1. Alpha particle radiography of small insects

    Energy Technology Data Exchange (ETDEWEB)

    Chingshen Su [National Tsing Hua Univ., Hsinchu (Taiwan) Inst. of Nuclear Science

    1993-12-31

    Radiographies of ants, mosquitoes, cockroaches and small bugs have been done with a radioisotope {sup 244}Cm alpha source. Energy of alpha particles was varied by attenuating the 5.81 MeV alpha particles with adjustable air spacings from the source to the sample. The LR-115 was used to register radiographs. The image of the insect registered on the LR-115 was etched out in a 2.5 N NaOH solution at 52{sup o}C for certain minutes, depending on various irradiation conditions for the insects. For larger insects, a scanning device for the alpha particle irradiation has been fabricated to take the radiograph of whole body of the insect, and the scanning period can be selected to give desired irradiation dosage. A CCDTV camera system connected to a microscope interfaced to an IBM/AT computer is used to register the microscopic image of the radiograph and to print it out with a video copy processor. (Author).

  2. Comparison of state dental radiography safety regulations.

    Science.gov (United States)

    McDaniel, Thomas F; Parashar, Vijay

    2015-01-01

    The aim of this study was to compare and provide an overview of state policies on occupational exposure, dosimetry, collimation, patient protection, and the use of portable handheld X-ray machines in dentistry. State government webpages containing radiation protection rules and regulations were scanned. The contents were compared against current federal regulations established by the Nuclear Regulatory Commission (NRC) and the US Food and Drug Administration (FDA). They were further evaluated in light of current recommendations from the National Council on Radiation Protection & Measurements (NCRP) and the American Dental Association (ADA). Most states' regulations mirror the exposure limits set forth by the NRC and FDA. Nonregulatory recommendations regarding use of dental radiography are periodically put forth by the NCRP and the ADA. State and federal agencies often follow recommendations from these scientific organizations when creating regulations. Clinicians must be aware of their state's radiation protection rules, as variations among states exist. In addition, recommendations published by organizations such as the NCRP and the ADA, while not legally binding, contribute significantly to the reduction of radiation risks for operators and patients alike.

  3. Portable Digital Radiography and Computed Tomography Manual

    Energy Technology Data Exchange (ETDEWEB)

    2007-11-01

    This user manual describes the function and use of the portable digital radiography and computed tomography (DRCT) scanner. The manual gives a general overview of x-ray imaging systems along with a description of the DRCT system. An inventory of the all the system components, organized by shipping container, is also included. In addition, detailed, step-by-step procedures are provided for all of the exercises necessary for a novice user to successfully collect digital radiographs and tomographic images of an object, including instructions on system assembly and detector calibration and system alignment. There is also a short section covering the limited system care and maintenance needs. Descriptions of the included software packages, the DRCT Digital Imager used for system operation, and the DRCT Image Processing Interface used for image viewing and tomographic data reconstruction are given in the appendixes. The appendixes also include a cheat sheet for more experienced users, a listing of known system problems and how to mitigate them, and an inventory check-off sheet suitable for copying and including with the machine for shipment purposes.

  4. Portable Digital Radiography and Computed Tomography Manual

    Energy Technology Data Exchange (ETDEWEB)

    2007-11-01

    This user manual describes the function and use of the portable digital radiography and computed tomography (DRCT) scanner. The manual gives a general overview of x-ray imaging systems along with a description of the DRCT system. An inventory of the all the system components, organized by shipping container, is also included. In addition, detailed, step-by-step procedures are provided for all of the exercises necessary for a novice user to successfully collect digital radiographs and tomographic images of an object, including instructions on system assembly and detector calibration and system alignment. There is also a short section covering the limited system care and maintenance needs. Descriptions of the included software packages, the DRCT Digital Imager used for system operation, and the DRCT Image Processing Interface used for image viewing and tomographic data reconstruction are given in the appendixes. The appendixes also include a cheat sheet for more experienced users, a listing of known system problems and how to mitigate them, and an inventory check-off sheet suitable for copying and including with the machine for shipment purposes.

  5. Towards Proton Therapy and Radiography at FAIR

    Science.gov (United States)

    Prall, M.; Lang, P. M.; LaTessa, C.; Mariam, F.; Merrill, F.; Shestov, L.; Simoniello, P.; Varentsov, D.; Durante, M.

    2015-04-01

    Protons having energies in the GeV range have been proposed as an alternative to Bragg-peak hadron therapy. This strategy reduces lateral scattering and overcomes uncertainties of particle range and relative biological effectiveness. GeV protons could additionally be used for targeting in image guided stereotactic radiosurgery. We experimentally demonstrated the potential of GeV protons for imaging of biological samples using E=0.8 GeV protons and the pRad setup at Los Alamos National Laboratory (LANL). In this setup, a system of magnetic lenses creates a point-to-point mapping from object to detector. This mapping compensates image blur due to lateral scattering inside the imaged (biological) object. We produced 2-dim proton radiographs of biological samples, an anthropomorphic phantom and performed simple dosimetry. High resolution tomographic reconstructions were derived from the 2-dim proton radiographs. Our experiment was performed within the framework of the PANTERA (Proton Therapy and Radiography) project. In the future, the proton microscope PRIOR (Proton Microscope for FAIR) located in the FAIR facility (Darmstadt), will focus on optimizing the technique for imaging of lesions implanted in animals and couple the irradiation with standard radiotherapy.

  6. Quantitative studies on inner interfaces in conical metal joints using hard x-ray inline phase contrast radiography

    Science.gov (United States)

    Zabler, S.; Rack, T.; Rack, A.; Nelson, K.

    2010-10-01

    Quantitative investigation of micrometer and submicrometer gaps between joining metal surfaces is applied to conical plug-socket connections in dental titanium implants. Microgaps of widths well beyond the resolving power of industrial x-ray systems are imaged by synchrotron phase contrast radiography. Furthermore, by using an analytical model for the relatively simple sample geometry and applying it to numerical forward simulations of the optical Fresnel propagation, we show that quantitative measurements of the microgap width down to 0.1 μm are possible. Image data recorded at the BAMline (BESSY-II light source, Germany) are presented, with the resolving power of the imaging system being 4 μm in absorption mode and ˜14 μm in phase contrast mode (z2=0.74 m). Thus, phase contrast radiography, combined with numerical forward simulations, is capable of measuring the widths of gaps that are two orders of magnitude thinner than the conventional detection limit.

  7. Dehydration of moulding sand in simulated casting process examined with neutron radiography

    Energy Technology Data Exchange (ETDEWEB)

    Schillinger, B., E-mail: Burkhard.Schillinger@frm2.tum.de [Technische Universitaet Muenchen, FRM II and Faculty for Physics E21, Lichtenbergstr. 1, 85748 Garching (Germany); Calzada, E. [Technische Universitaet Muenchen, FRM II and Faculty for Physics E21, Lichtenbergstr. 1, 85748 Garching (Germany); Eulenkamp, C.; Jordan, G.; Schmahl, W.W. [Ludwig-Maximilians-Universitaet Muenchen, Department fuer Geo- und Umweltwissenschaften, Sektion Kristallographie, Theresienstr. 41, 80333 Muenchen (Germany)

    2011-09-21

    Natural bentonites are an important material in the casting industry. Smectites as the main component of bentonites plasticize and stabilise sand moulds. Pore water as well as interlayer water within the smectites are lost as a function of time, location and temperature. Although rehydration of the smectites should be a reversible process, the industrially dehydrated smectites lose their capability to reabsorb water. This limits the number of possible process cycles of the mould material. A full understanding of the dehydration process would help to optimise the amount of fresh material to be added and thus save resources. A simulated metal casting was investigated with neutron radiography at the ANTARES neutron imaging facility of the FRM II reactor of Technische Universitaet Muenchen, Germany.

  8. Dehydration of moulding sand in simulated casting process examined with neutron radiography

    Science.gov (United States)

    Schillinger, B.; Calzada, E.; Eulenkamp, C.; Jordan, G.; Schmahl, W. W.

    2011-09-01

    Natural bentonites are an important material in the casting industry. Smectites as the main component of bentonites plasticize and stabilise sand moulds. Pore water as well as interlayer water within the smectites are lost as a function of time, location and temperature. Although rehydration of the smectites should be a reversible process, the industrially dehydrated smectites lose their capability to reabsorb water. This limits the number of possible process cycles of the mould material. A full understanding of the dehydration process would help to optimise the amount of fresh material to be added and thus save resources. A simulated metal casting was investigated with neutron radiography at the ANTARES neutron imaging facility of the FRM II reactor of Technische Universität München, Germany.

  9. Clinical application of computed radiography; Comparison of computed radiography and conventional radiography in the detection of microcalcifications and pulmonary nodules

    Energy Technology Data Exchange (ETDEWEB)

    Higashida, Yoshiharu (Kumamoto Univ. (Japan). Coll. of Medical Science)

    1990-10-01

    Observer performance tests were performed to compare the diagnostic accuracy of digitized storage phosphors and conventional radiography in the detection of microcalcification in the breast and pulmonary nodules. Clustered microcalcifications were randomly superimposed on a human breast specimen. Two types of screen-film systems (Toshiba MM6/Fuji MINC, Kodak MinR/Kodak MinR) and CR images either with unsharp mask or with no image processing (unprocess) were used as imaging systems. Nine readers assessed the capability of screen-films, and unsharp-masked and unprocessed mammograms to detect microcalcifications. Observer performance data were evaluated by receiver operating characteristics (ROC) analysis. Both the area under ROC curve and the true positive localization fraction were used as performance indexes. Two screen-film images provided a higher detectability of microcalcifications than CR images. In the detectability of microcalcifications, unsharp-masked images were superior to unprocessed images. CR images showed higher false positive fraction than screen-film systems. To assess the detectability of pulmonary nodules, 15 radiologists compared the diagnostic accuracy of screen-film system and CR images, including unprocessed, unsharp-masked, reversed and paired images, in 18 normal volunteers and 18 patients with pulmonary nodules. Overall diagnostic accuracy of CR images, except for reversed images, were comparable to the screen-film system. In case of definite, large nodules, unprocessed, unsharp-masked, and paired images were superior to the screen-film and reversed images. Screen-film and unprocessed images were helpful in cases of tiny nodules without definite contrast. 59 refs.

  10. Comparison of the diagnostic accuracy of direct digital radiography system, filtered images, and subtraction radiography

    Directory of Open Access Journals (Sweden)

    Wilton Mitsunari Takeshita

    2013-01-01

    Full Text Available Background: To compare the diagnostic accuracy of three different imaging systems: Direct digital radiography system (DDR-CMOS, four types of filtered images, and a priori and a posteriori registration of digital subtraction radiography (DSR in the diagnosis of proximal defects. Materials and Methods: The teeth were arranged in pairs in 10 blocks of vinyl polysiloxane, and proximal defects were performed with drills of 0.25, 0.5, and 1 mm diameter. Kodak RVG 6100 sensor was used to capture the images. A posteriori DSR registrations were done with Regeemy 0.2.43 and subtraction with Image Tool 3.0. Filtered images were obtained with Kodak Dental Imaging 6.1 software. Images (n = 360 were evaluated by three raters, all experts in dental radiology. Results: Sensitivity and specificity of the area under the receiver operator characteristic (ROC curve (Az were higher for DSR images with all three drills (Az = 0.896, 0.979, and 1.000 for drills 0.25, 0.5, and 1 mm, respectively. The highest values were found for 1-mm drills and the lowest for 0.25-mm drills, with negative filter having the lowest values of all (Az = 0.631. Conclusion: The best method of diagnosis was by using a DSR. The negative filter obtained the worst results. Larger drills showed the highest sensitivity and specificity values of the area under the ROC curve.

  11. A method to optimize the processing algorithm of a computed radiography system for chest radiography.

    Science.gov (United States)

    Moore, C S; Liney, G P; Beavis, A W; Saunderson, J R

    2007-09-01

    A test methodology using an anthropomorphic-equivalent chest phantom is described for the optimization of the Agfa computed radiography "MUSICA" processing algorithm for chest radiography. The contrast-to-noise ratio (CNR) in the lung, heart and diaphragm regions of the phantom, and the "system modulation transfer function" (sMTF) in the lung region, were measured using test tools embedded in the phantom. Using these parameters the MUSICA processing algorithm was optimized with respect to low-contrast detectability and spatial resolution. Two optimum "MUSICA parameter sets" were derived respectively for maximizing the CNR and sMTF in each region of the phantom. Further work is required to find the relative importance of low-contrast detectability and spatial resolution in chest images, from which the definitive optimum MUSICA parameter set can then be derived. Prior to this further work, a compromised optimum MUSICA parameter set was applied to a range of clinical images. A group of experienced image evaluators scored these images alongside images produced from the same radiographs using the MUSICA parameter set in clinical use at the time. The compromised optimum MUSICA parameter set was shown to produce measurably better images.

  12. A benchmark for comparison of dental radiography analysis algorithms.

    Science.gov (United States)

    Wang, Ching-Wei; Huang, Cheng-Ta; Lee, Jia-Hong; Li, Chung-Hsing; Chang, Sheng-Wei; Siao, Ming-Jhih; Lai, Tat-Ming; Ibragimov, Bulat; Vrtovec, Tomaž; Ronneberger, Olaf; Fischer, Philipp; Cootes, Tim F; Lindner, Claudia

    2016-07-01

    Dental radiography plays an important role in clinical diagnosis, treatment and surgery. In recent years, efforts have been made on developing computerized dental X-ray image analysis systems for clinical usages. A novel framework for objective evaluation of automatic dental radiography analysis algorithms has been established under the auspices of the IEEE International Symposium on Biomedical Imaging 2015 Bitewing Radiography Caries Detection Challenge and Cephalometric X-ray Image Analysis Challenge. In this article, we present the datasets, methods and results of the challenge and lay down the principles for future uses of this benchmark. The main contributions of the challenge include the creation of the dental anatomy data repository of bitewing radiographs, the creation of the anatomical abnormality classification data repository of cephalometric radiographs, and the definition of objective quantitative evaluation for comparison and ranking of the algorithms. With this benchmark, seven automatic methods for analysing cephalometric X-ray image and two automatic methods for detecting bitewing radiography caries have been compared, and detailed quantitative evaluation results are presented in this paper. Based on the quantitative evaluation results, we believe automatic dental radiography analysis is still a challenging and unsolved problem. The datasets and the evaluation software will be made available to the research community, further encouraging future developments in this field. (http://www-o.ntust.edu.tw/~cweiwang/ISBI2015/).

  13. Dual-energy subtraction radiography of the breast

    Energy Technology Data Exchange (ETDEWEB)

    Asaga, Taro; Masuzawa, Chihiro; Kawahara, Satoru; Motohashi, Hisahiko; Okamoto, Takashi; Tamura, Nobuo

    1988-06-01

    Dual-energy projection radiography was applied to breast examination. To perform the dual-energy subtraction radiography using a digital radiography unit, high and low-energy exposures were made at an appropriate time interval under differing X-ray exposure conditions. Dual-energy subtraction radiography was performed in 41 cancer patients in whom the tumor shadow was equivocal or the border of cancer infiltration was not clearly demonstrated by compression mammography, and 15 patients with benign diseases such as fibrocystic disease, cyst and fibroadenoma. In 21 cases out of the 41 cancer patients, the dual-energy subtraction radiography clearly visualized the malignant tumor shadows and the border of cancer infiltration and the daughter nodules by removing the shadows of normal mammary gland. On the other hand, beign diseases such as fibrocystic disease and cyst could be diagnosed as such, because the tumor shadow and the irregularly concentrated image of mammary gland disappeared by the dual-energy subtraction. These results suggest that this new technique will be useful in examination of breast masses.

  14. Application of digital radiography in the analysis of cultural heritage

    Energy Technology Data Exchange (ETDEWEB)

    Oiveira, Davi F.; Calza, Cristiane; Rocha, Henrique S.; Nascimento, Joseilson R.; Lopes, Ricardo T., E-mail: davi@lin.ufrj.br, E-mail: ccalza@lin.ufrj.br, E-mail: henrique@lin.ufrj.br, E-mail: joseilson@lin.ufrj.br, E-mail: ricardo@lin.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Instrumentacao Nuclear

    2013-07-01

    The scientific examination of artworks has gained increasing interest in the last years, allowing the characterization of materials and techniques employed by the artists. This analysis can be extremely valuable to conservation and restoration treatments. However, the fact that every artworks is a unique piece emphasizes the necessity of working with non-destructive techniques. Although radiography has been used in the technical examination of museum objects for many decades, digital radiography is rapidly becoming a preferred modality for this essential tool in the advanced examination of works of art. The ability to electronically combine images from the large painting into a single composite image file was extremely valuable and results in higher quality images than those achieved with conventional radiography. These images can be also processed and improved using adequate software. Additional advantages of digital radiography include the possibility of an almost immediate analysis of the results, use of an only recording film and absence of chemical processing. Radiographic imaging can be applied to the analysis of virtually all media including paintings, sculptures, woodworks, engravings, etc. This paper reports some case studies of the use of digital radiography in the study of paintings and sculptures, showing the feasibility and advantages of this technique for this kind of purpose. The radiographic images revealed the conservation state of the analyzed objects and various details of its execution in order to assist recently restoration processes. (author)

  15. Acute Knee Trauma: Analysis of Multidetector Computed Tomography Findings and Comparison with Conventional Radiography

    Energy Technology Data Exchange (ETDEWEB)

    Mustonen, A.O.T. [Helsinki Univ. Central Hospital (Finland). Dept. of Radiology; Koskinen, S.K. [Research Inst. of Military Medicine, Helsinki (Finland); Kiuru, M.J. [ORTON Orthopaedic Hospital, Helsinki (Finland)

    2005-12-01

    Purpose: To evaluate the multidetector computed tomography (MDCT) findings of acute knee trauma and to compare radiography with MDCT in patients referred ta level 1 trauma center. Material and Methods: During a 5-year period, a total of 415 MDCT examinations were performed on 409 patients with acute knee trauma to reveal complex fracture anatomy or rule out a fracture. MDCT and primary radiographs were re-evaluated with respect to fracture location and trauma mechanism. Tibial plateau fractures were further analyzed depending on anatomical location: anterior-medial, anterior-lateral, posterior-lateral, and posterior-medial regions. Maximal depression of the tibial articular surface was measured. Findings on the primary knee radiographs were compared with MDCT findings. Results: Of the 409 patients, 356 (87%) had a knee fracture. A total of 451 fractures were found in all anatomic regions: distal femur ( n = 49), proximal tibia ( n 307), patella ( n = 23), and proximal fibula ( n = 72). Primary radiographs were available in 316 (76%) cases. Of these, 225 (71%) had MDCT in order to reveal the fracture anatomy better, and 91 (29%) had a subsequent MDCT after negative plain radiographs. Overall sensitivity of radiography was 83%, while negative predictive value was 49%. On radiography, tibial plateau articular depression was underestimated in all regions except when the fracture consisted of the whole half of the anterior or posterior plateau. The three main injury mechanisms were traffic accident, a simple fall, and sport. In 49 cases (15%), primary radiographs were suboptimal due to positioning. Conclusion: In severely injured patients, diagnostically sufficient radiographs are difficult to obtain, and therefore a negative radiograph is not reliable in ruling out a fracture. In these patients, MDCT is a fast and accurate examination and is also recommended in patients with tibial plateau fractures or complex knee injuries in order to evaluate the fracture adequately.

  16. Study of pipe thickness loss using a neutron radiography method

    Energy Technology Data Exchange (ETDEWEB)

    Mohamed, Abdul Aziz; Wahab, Aliff Amiru Bin [Universiti Tenaga Nasional, Jalan IKRAM-UNITEN, 43000 Kajang, Selangor (Malaysia); Yazid, Hafizal B.; Ahmad, Megat Harun Al Rashid B. Megat; Jamro, Rafhayudi B.; Azman, Azraf B.; Zin, Muhamad Rawi Md; Idris, Faridah Mohamad [Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

    2014-02-12

    The purpose of this preliminary work is to study for thickness changes in objects using neutron radiography. In doing the project, the technique for the radiography was studied. The experiment was done at NUR-2 facility at TRIGA research reactor in Malaysian Nuclear Agency, Malaysia. Test samples of varying materials were used in this project. The samples were radiographed using direct technique. Radiographic images were recorded using Nitrocellulose film. The films obtained were digitized to processed and analyzed. Digital processing is done on the images using software Isee!. The images were processed to produce better image for analysis. The thickness changes in the image were measured to be compared with real thickness of the objects. From the data collected, percentages difference between measured and real thickness are below than 2%. This is considerably very low variation from original values. Therefore, verifying the neutron radiography technique used in this project.

  17. NEUTRON RADIOGRAPHY (NRAD) REACTOR 64-ELEMENT CORE UPGRADE

    Energy Technology Data Exchange (ETDEWEB)

    John D. Bess

    2014-03-01

    The neutron radiography (NRAD) reactor is a 250 kW TRIGA (registered) (Training, Research, Isotopes, General Atomics) Mark II , tank-type research reactor currently located in the basement, below the main hot cell, of the Hot Fuel Examination Facility (HFEF) at the Idaho National Laboratory (INL). It is equipped with two beam tubes with separate radiography stations for the performance of neutron radiography irradiation on small test components. The interim critical configuration developed during the core upgrade, which contains only 62 fuel elements, has been evaluated as an acceptable benchmark experiment. The final 64-fuel-element operational core configuration of the NRAD LEU TRIGA reactor has also been evaluated as an acceptable benchmark experiment. Calculated eigenvalues differ significantly (approximately +/-1%) from the benchmark eigenvalue and have demonstrated sensitivity to the thermal scattering treatment of hydrogen in the U-Er-Zr-H fuel.

  18. Wind Turbine Blade Nondestructive Testing with a Transportable Radiography System

    Directory of Open Access Journals (Sweden)

    J. G. Fantidis

    2011-01-01

    Full Text Available Wind turbines are becoming widely used as they are an environmentally friendly way for energy production without emissions; however, they are exposed to a corrosive environment. In addition, as wind turbines typically are the tallest structures in the surrounding area of a wind farm, it is expected that they will attract direct lightning strikes several times during their operating life. The purpose of this paper is to show that the radiography with a transportable unit is a solution to find defects in the wind turbine blade and reduce the cost of inspection. A transportable neutron radiography system, incorporating an Sb–Be source, has been simulated using the MCNPX code. The simulated system has a wide range of radiography parameters.

  19. Experimental Study on Neutron Radiography Device Based on Reactor

    Institute of Scientific and Technical Information of China (English)

    LU; Jin; PENG; Dan; HAO; Qian; YU; Bo-xiang; LI; Yi-guo

    2012-01-01

    <正>Neutron radiography is a non-destructive testing developing fast recently, which requires stable and proper neutron source with low γ background. Neutrons from In-hospital Neutron Irradiator (IHNI) could meet this requirement. Based on the neutron beams of IHNI, a collimator is designed and built for neutron radiography. The experiment results show that in the case of IHNI working at normal rated power, the neutron flux at the end of the collimator is 1.43×106 cm-2·s-1; The max collimation ratio (L/D) is 58; the γ dose rate is 6.3×106 mSv/s. In a word, the collimator could be used for neutron radiography.

  20. Proton Radiography as an electromagnetic field and density perturbation diagnostic

    Energy Technology Data Exchange (ETDEWEB)

    Mackinnon, A; Patel, P; Town, R; Edwards, M; Phillips, T; Lerner, S; Price, D; Hicks, D; Key, M; Hatchett, S; Wilks, S; King, J; Snavely, R; Freeman, R; Boehlly, T; Koenig, M; Martinolli, E; Lepape, S; Benuzzi-Mounaix, A; Audebert, P; Gauthier, J; Borghesi, M; Romagnani, L; Toncian, T; Pretzler, G; Willi, O

    2004-04-15

    Laser driven proton beams have been used to diagnose transient fields and density perturbations in laser produced plasmas. Grid deflectometry techniques have been applied to proton radiography to obtain precise measurements of proton beam angles caused by electromagnetic fields in laser produced plasmas. Application of proton radiography to laser driven implosions has demonstrated that density conditions in compressed media can be diagnosed with MeV protons. This data has shown that proton radiography can provide unique insight into transient electromagnetic fields in super critical density plasmas and provide a density perturbation diagnostics in compressed matter . PACS numbers: 52.50.Jm, 52.40.Nk, 52.40.Mj, 52.70.Kz

  1. Magnifying lens for 800 MeV proton radiography.

    Science.gov (United States)

    Merrill, F E; Campos, E; Espinoza, C; Hogan, G; Hollander, B; Lopez, J; Mariam, F G; Morley, D; Morris, C L; Murray, M; Saunders, A; Schwartz, C; Thompson, T N

    2011-10-01

    This article describes the design and performance of a magnifying magnetic-lens system designed, built, and commissioned at the Los Alamos National Laboratory (LANL) for 800 MeV flash proton radiography. The technique of flash proton radiography has been developed at LANL to study material properties under dynamic loading conditions through the analysis of time sequences of proton radiographs. The requirements of this growing experimental program have resulted in the need for improvements in spatial radiographic resolution. To meet these needs, a new magnetic lens system, consisting of four permanent magnet quadrupoles, has been developed. This new lens system was designed to reduce the second order chromatic aberrations, the dominant source of image blur in 800 MeV proton radiography, as well as magnifying the image to reduce the blur contribution from the detector and camera systems. The recently commissioned lens system performed as designed, providing nearly a factor of three improvement in radiographic resolution.

  2. Studies of solid propellant combustion with pulsed radiography

    Science.gov (United States)

    Godai, T.; Tanemura, T.; Fujiwara, T.; Shimizu, M.

    1987-01-01

    Pulsed radiography was applied to observe solid propellant surface regression during rocket motor operation. Using a 150 KV flash X-ray system manufactured by the Field Emission Corporation and two kinds of film suppliers, images of the propellant surface of a 5 cm diameter end burning rocket motor were recorded on film. The repetition frame rate of 8 pulses per second and the pulse train length of 10 pulses are limited by the capability of the power supply and the heat build up within the X-ray tube, respectively. The experiment demonstrated the effectiveness of pulsed radiography for observing solid propellant surface regression. Measuring the position of burning surface images on film with a microdensitometer, quasi-instantaneous burning rate as a function of pressure and the variation of characteristic velocity with pressure and gas stay time were obtained. Other research items to which pulsed radiography can be applied are also suggested.

  3. Application of Neutron Radiography to Flow Visualization in Supercritical Water

    Science.gov (United States)

    Takenaka, N.; Sugimoto, K.; Takami, S.; Sugioka, K.; Tsukada, T.; Adschiri, T.; Saito, Y.

    Supercritical water is used in various chemical reaction processes including hydrothermal synthesis of metal oxide nano-particles, oxidation, chemical conversion of biomass and plastics. Density of the super critical water is much less than that of the sub-critical water. By using neutron radiography, Peterson et al. have studied salt precipitation processes in supercritical water and the flow pattern in a reverse-flow vessel for salt precipitation, and Balasko et al. have revealed the behaviour of supercritical water in a container. The nano-particles were made by mixing the super critical flow and the sub critical water solution. In the present study, neutron radiography was applied to the flow visualization of the super and sub critical water mixture in a T-junction made of stainless steel pipes for high pressure and temperature conditions to investigate their mixing process. Still images by a CCD camera were obtained by using the neutron radiography system at B4 port in KUR.

  4. Deterministic simulation of thermal neutron radiography and tomography

    Science.gov (United States)

    Pal Chowdhury, Rajarshi; Liu, Xin

    2016-05-01

    In recent years, thermal neutron radiography and tomography have gained much attention as one of the nondestructive testing methods. However, the application of thermal neutron radiography and tomography is hindered by their technical complexity, radiation shielding, and time-consuming data collection processes. Monte Carlo simulations have been developed in the past to improve the neutron imaging facility's ability. In this paper, a new deterministic simulation approach has been proposed and demonstrated to simulate neutron radiographs numerically using a ray tracing algorithm. This approach has made the simulation of neutron radiographs much faster than by previously used stochastic methods (i.e., Monte Carlo methods). The major problem with neutron radiography and tomography simulation is finding a suitable scatter model. In this paper, an analytic scatter model has been proposed that is validated by a Monte Carlo simulation.

  5. JB/T4730.11射线数字成像标准制定的关键技术探讨%The Key Technology Discussing of JB/T 4730. 11 Digital Radiography Standard Setting

    Institute of Scientific and Technical Information of China (English)

    梁丽红

    2011-01-01

    In order to popularize application of digital radiography technology in the special equipment field, and promote the special inspecting level in nondestructive testing industry, improve the efficiency of special equipment inspecting, and reduce the inspecting complexity for staff, and decrease environmental pollution. The advanced technology of digital radiography should be masted and the relevant testing standards should be established. Some key technologies of standards setting include: ① The components of digital radiography system in standards. ② The differences of image quality evaluation between digital radiography and film radiography. ③ The consistency and equivalence between digital radiography and film radiography. ④other technologies should be concerned in digital radiography.%为在特种设备行业推广和应用射线数字成像检测技术。提高特种设备检测效率、降低检测人员的工作强度、减少环境污染,提升特检行业的无损检测水平,必须掌握先进的数字成像检测技术,制定相关的检测标准。以下是标准制定的几个关键问题:①标准包含的射线数字成像检测系统及其内容。②数字成像与胶片照相像质评价指标的区别。③数字成像与胶片照相像质的等效问题。④数字成像技术应用应关注的其它问题。

  6. Recent developments in a CdTe-based x-ray detector for digital radiography

    Science.gov (United States)

    Glasser, Francis; Martin, Jean-Luc; Thevenin, Bernard; Schermesser, Patrick; Pantigny, Philippe; Laurent, Jean Yves; Rambaud, Philippe; Pitault, Bernard; Paltrier, Sylvain

    1997-05-01

    The performance of a new CdTe based x-ray detector devoted to digital radiography are presented. The detectors consist of a 6 cm2 CdTe 2D-array connected to CMOS readout circuit by indium bumps. The final image has 400 X 600 pixels with a 50 micron pitch. This solid-state detector presents the advantages of direct conversion, i.e. high stopping power with high spatial resolution and a significantly higher signal than commercially available scintillator/photodetector systems. The experimental results show excellent linearity, spatial resolution and detective quantum efficiency. The MTF was measured by the angled-slit method: 20 to 30 percent at 10 1p/mm depending on the incident x-ray energy. The measured DQE is about 0.8 at 40 KeV and 100 (mu) Gray dose. Our simulation shows that these experimental results do not reach the theoretical limit. Further improvements are in progress. The first industrial application will be dental radiography due to the small size and the excellent performances. We also tested the detector with x-rays form 20 KeV to 1.25 MeV. Of course the CdTe thickness should then be adapted to the incident x-ray energy.

  7. A dynamic material discrimination algorithm for dual MV energy X-ray digital radiography.

    Science.gov (United States)

    Li, Liang; Li, Ruizhe; Zhang, Siyuan; Zhao, Tiao; Chen, Zhiqiang

    2016-08-01

    Dual-energy X-ray radiography has become a well-established technique in medical, industrial, and security applications, because of its material or tissue discrimination capability. The main difficulty of this technique is dealing with the materials overlapping problem. When there are two or more materials along the X-ray beam path, its material discrimination performance will be affected. In order to solve this problem, a new dynamic material discrimination algorithm is proposed for dual-energy X-ray digital radiography, which can also be extended to multi-energy X-ray situations. The algorithm has three steps: α-curve-based pre-classification, decomposition of overlapped materials, and the final material recognition. The key of the algorithm is to establish a dual-energy radiograph database of both pure basis materials and pair combinations of them. After the pre-classification results, original dual-energy projections of overlapped materials can be dynamically decomposed into two sets of dual-energy radiographs of each pure material by the algorithm. Thus, more accurate discrimination results can be provided even with the existence of the overlapping problem. Both numerical and experimental results that prove the validity and effectiveness of the algorithm are presented.

  8. Correction parameters in conventional dental radiography for dental implant

    Directory of Open Access Journals (Sweden)

    Barunawaty Yunus

    2009-12-01

    Full Text Available Background: Radiographic imaging as a supportive diagnostic tool is the essential component in treatment planning for dental implant. It help dentist to access target area of implant due to recommendation of many inventions in making radiographic imaging previously. Along with the progress of science and technology, the increasing demand of easier and simpler treatment method, a modern radiographic diagnostic for dental implant is needed. In fact, Makassar, especially in Faculty of Dentistry Hasanuddin University, has only a conventional dental radiography. Researcher wants to optimize the equipment that is used to obtain parameters of the jaw that has been corrected to get accurate dental implant. Purpose: This study aimed to see the difference of radiographic imaging of dental implant size which is going to be placed in patient before and after correction. Method: The type of research is analytical observational with cross sectional design. Sampling method is non random sampling. The amount of samples is 30 people, male and female, aged 20–50 years old. The correction value is evaluated from the parameter result of width, height, and thick of the jaw that were corrected with a metal ball by using conventional dental radiography to see the accuracy. Data is analyzed using SPSS 14 for Windows program with T-test analysis. Result: The result that is obtained by T-Test analysis results with significant value which p<0.05 in the width and height of panoramic radiography technique, the width and height of periapical radiography technique, and the thick of occlusal radiography technique before and after correction. Conclusion: It can be concluded that there is a significant difference before and after the results of panoramic, periapical, and occlusal radiography is corrected.

  9. Technical and clinical breast cancer screening performance indicators for computed radiography versus direct digital radiography

    Energy Technology Data Exchange (ETDEWEB)

    Bosmans, Hilde; Lemmens, Kim; Zanca, Federica; Ongeval, Chantal van; Steen, Andre van [University Hospitals Leuven, Department of Radiology, Leuven (Belgium); Hauwere, An de; Thierens, Hubert [Ghent University, QCC, Ghent (Belgium); Herck, Koen van; Bleyen, Luc; Mortier, Griet [Ghent University, Centrum voor Preventie en Vroegtijdige Opsporing van Kanker, Department of Public Health, Ghent (Belgium); Martens, Patrick [Vroegtijdige Opsporing Borstklierkanker West-Vlaanderen vzw, Bruges (Belgium); Putte, Gretel vande; Kellen, Eliane; Limbergen, Erik van [Leuven University Center of Cancer Screening, Leuven (Belgium)

    2013-10-15

    To compare technical and clinical screening performance parameters between computed radiography (CR) and direct digital radiography (DR) systems. The number of women screened with CR was 73,008 and with DR 116,945. Technical and patient dose survey data of 25 CR and 37 DR systems were available. Technical performance was expressed by threshold thickness values at the mean glandular dose (MGD) level of routine practice. Clinical indicators included recall rate (RR), cancer detection rate (CDR), percentage of ductal carcinoma in situ (DCIS), percentage of cancers with T-scores smaller than 1 cm and positive predictive value (PPV). Contrast threshold values for the 0.1-mm gold disk were 1.44 {mu}m (SD 0.13 {mu}m) for CR and 1.20 {mu}m (SD 0.13 {mu}m for DR). MGD was 2.16 mGy (SD 0.36 mGy) and 1.35 mGy (SD 0.32 mGy) for CR and DR respectively. We obtained for CR, respectively DR, the following results: RR in the first round of 5.48 % versus 5.61 %; RR in subsequent rounds of 2.52 % versus 2.65 %; CDR of 0.52 % versus 0.53 %; DCIS of 0.08 % versus 0.11 %; a rate of cancers with T-scores smaller than 1 cm of 0.11 % versus 0.11 %; PPV of 18.45 % versus 18.64 %; none of them was significantly different. Our screening indicators are reassuring for the use of CR and DR, with CR operating at 60 % higher MGD. (orig.)

  10. Vibration Analysis of Digital Radiography System for Large Container Inspection

    Institute of Scientific and Technical Information of China (English)

    黄松岭; 李路明; 周立业; 向新程; 安继刚

    2003-01-01

    The cantilever vibration characteristics of a digital radiography system were analyzed to predict the effect of vibration on the performance of a mobile container inspection system. The static deformation,vibration mode and natural frequency of the cantilever of the digital radiography system were calculated with the ALGOR Finite Element System to verify the strength and rigidity of the cantilever. The maximum amplitude of the cantilever vibration occurs as it starts accelerating. The predictions show good agreement with test results, indicating that the finite element model of the cantilever structure accurately models the mechanical characteristics.

  11. Neutron radiography and tomography facility at IBR-2 reactor

    Science.gov (United States)

    Kozlenko, D. P.; Kichanov, S. E.; Lukin, E. V.; Rutkauskas, A. V.; Belushkin, A. V.; Bokuchava, G. D.; Savenko, B. N.

    2016-05-01

    An experimental station for investigations using neutron radiography and tomography was developed at the upgraded high-flux pulsed IBR-2 reactor. The 20 × 20 cm neutron beam is formed by the system of collimators with the characteristic parameter L/D varying from 200 to 2000. The detector system is based on a 6LiF/ZnS scintillation screen; images are recorded using a high-sensitivity video camera based on the high-resolution CCD matrix. The results of the first neutron radiography and tomography experiments at the developed facility are presented.

  12. Proton radiography, nuclear cross sections and multiple Coulomb scattering

    Energy Technology Data Exchange (ETDEWEB)

    Sjue, Sky K. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-11-04

    The principles behind proton radiography including multiple Coulomb scattering are discussed for a purely imaginary square well nucleus in the eikonal approximation. It is found that a very crude model can reproduce the angular dependence of the cross sections measured at 24 GeV/c. The largest differences are ~3% for the 4.56 mrad data, and ~4% for the 6.68 mrad data. The prospect of understanding how to model deterministically high-energy proton radiography over a very large range of energies is promising, but it should be tested more thoroughly.

  13. Quality-controlled dose reduction of full-leg radiography in patients with knee malalignment

    Energy Technology Data Exchange (ETDEWEB)

    Kloth, Jost Karsten; Neumann, Regina; Stiller, Wolfram; Kauczor, Hans-Ulrich; Weber, Marc-Andre [University Hospital Heidelberg, Department of Diagnostic and Interventional Radiology, Heidelberg (Germany); Stillfried, Eva von; Ewerbeck, Volker [University Hospital Heidelberg, Department of Orthopedic and Trauma Surgery, Heidelberg (Germany)

    2014-12-05

    Digital plain radiographs of the full leg are frequently performed examinations of children and young adults. Thus, the objective of this work was to reduce the radiation exposure dependent on specific indications, and to determine objective quality-control criteria to ensure accurate assessment. Institutional review board approval and informed consent of all participants were obtained. In this prospective, randomized controlled, blinded, two-armed single-center study, 288 evaluable patients underwent plain radiography of the full leg with standard and reduced doses. The evaluation of the plain radiographs was conducted using the following criteria: mechanical axis, leg length, and maturation of the epiphyseal plate. Two blinded radiologists evaluated these criteria using a score ranging from 1 (definitely assessable) to 4 (not assessable). If a single criterion had been evaluated with a score of 3 or more points or all criteria with 2 points, the radiograph was scored as ''not assessable''. The study was designed as a non-inferiority trial. Eleven (3.8 %) examined X-rays were scored as not assessable. The rate of non-assessable radiographs with 33 % reduced dose was significantly not inferior to the rate of non-assessable radiographs with standard dose. The evaluation of the quality criteria was dose independent. Full-leg plain radiography in patients with knee malalignment can be performed at 33 % reduced dose without loss of relevant diagnostic information. (orig.)

  14. Evaluation of the Entrance Surface Dose (ESD and Radiation Dose to the Radiosensitive Organs in Pediatric Pelvic Radiography

    Directory of Open Access Journals (Sweden)

    Vahid Karami

    2017-06-01

    Full Text Available Background Patients' dosimetry is crucial in order to enhance radiation protection optimization and to deliver low radiation dose to the patients in a radiological procedure. The aim of this study was to assess the entrance surface dose (ESD and radiation dose to the radiosensitive organs in pediatric pelvic radiography. Materials and Methods The studied population included 98 pediatric patients of both genders referred to anteroposterior (AP projection of pelvic radiography. The radiation dose was directly measured using high radiosensitive cylindrical lithium fluoride thermo-luminescent dosimeters (TLD-GR200. Two TLDs were placed at the center point of the radiation field to measure the ESD of pelvis. Moreover for each patient, 2 TLDs were placed upon each eyelid, 2 TLDs upon each breast, 2 TLDs upon the surface anatomical position of the thyroid gland and finally 2 TLDs at the surface anatomical position of the gonads to measure the received dose. Results The ESD ± standard deviation for AP pelvic radiography was obtained 591.7±76 µGy. Statistically significant difference was obtained between organs located outside and inside of the radiation field with respect to dose received (P

  15. A call center primer.

    Science.gov (United States)

    Durr, W

    1998-01-01

    Call centers are strategically and tactically important to many industries, including the healthcare industry. Call centers play a key role in acquiring and retaining customers. The ability to deliver high-quality and timely customer service without much expense is the basis for the proliferation and expansion of call centers. Call centers are unique blends of people and technology, where performance indicates combining appropriate technology tools with sound management practices built on key operational data. While the technology is fascinating, the people working in call centers and the skill of the management team ultimately make a difference to their companies.

  16. Replacement of radiography with ultrasonic phased array for feeder tubes in CANDU reactors using ASME code case N-659-2

    Energy Technology Data Exchange (ETDEWEB)

    Simmons, R.; Bower, Q.; Arseneau, S., E-mail: bsimmons@metalogicinspection.com, E-mail: qbower@metalogicinspection.com, E-mail: sarseneau@metalogicinspection.com [Metalogic Inspection Services, Edmonton, Alberta (Canada)

    2013-07-01

    In this paper we will discuss phased array technology for the replacement of radiography on new construction projects in the nuclear industry. Specifically, through the implementation of A.S.M.E. code N-659-2 and MetaPhase phased array services. Phased Array is not considered a new technique on in service welds in the nuclear industry; however it was unprecedented on new construction welds and required significant investment in regulatory approval (C.N.S.C.), technology research and development, regulatory, client and technician training for successful service implementation. This paper will illustrate the abilities and limitations associated in replacing radiography with MetaPhase, as well as the substantial benefits relative to increased production, improved weld quality, enhanced safety and overall project cost savings. (author)

  17. Detection of urinary stones at reduced radiation exposure: a phantom study comparing computed radiography and a low-dose digital radiography linear slit scanning system

    Science.gov (United States)

    Szucs-Farkas, Zsolt; Chakraborty, D. P.; Thoeny, Harriet C.; Loupatatzis, Christos; Vock, Peter; Harald, Bonel

    2010-01-01

    Objective In this experimental study we assessed the diagnostic performance of linear slit scanning radiography (LSSR) compared to conventional computed radiography (CR) in the detection of urinary calculi in an anthropomorphic phantom imitating patients weighing approximately 58 to 88 kg. Conclusion Compared to computed radiography, LSSR is superior in the detection of urinary stones and may be used for pretreatment localization and follow-up at a lower patient exposure. PMID:19457787

  18. The value of thyroid shielding in intraoral radiography

    NARCIS (Netherlands)

    Hoogeveen, R.C.; Hazenoot, B.; Sanderink, G.C.H.; Berkhout, W.E.R.

    2016-01-01

    Objectives: To evaluate the utility of the application of a thyroid shield in intraoral radiography when using rectangular collimation. Methods: Experimental data were obtained by measuring the absorbed dose at the position of the thyroid gland in a RANDO® (The Phantom Laboratory, Salem, NY) male ph

  19. Neutron induced electron radiography; Radiografia com eletrons induzida por neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Marcos Leandro Garcia

    2008-07-01

    In the present paper a new radiography technique, the 'Neutron Induced Electron Radiography' - NIER, to inspect low thickness samples on the order of micra, has been developed. This technique makes use of low energy electrons as penetrating radiation generated from metallic gadolinium screens when irradiated by thermal neutrons. The conditions to obtain the best image for the conventional X-ray film Kodak-AA were determined by using a digital system to quantify the darkening level of the film. The irradiations have been performed at a radiography equipment installed at the beam-hole no. 8 of the 5 MW IEA-R1 nuclear research reactor of IPEN-CNEN/SP. The irradiation time to obtain the best radiography was 100 seconds and for such condition the technique was able to discern 1 {mu}m in 24 {mu}m of aluminum at a resolution of 32 {mu}m. By visual comparison the images obtained by the NIER shown a higher quality when compared with the ones from other usual techniques the make use of electrons a penetrating radiation and films for image registration. Furthermore the use of the digital system has provided a smaller time for data acquisition and data analysis as well as an improvement in the image visualization. (author)

  20. Point Scattered Function (PScF) for fast neutron radiography

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, Mohamed H. [Nuclear and Radiation Engineering Department, Alexandria University, Alexandria 21544 (Egypt)], E-mail: mhmheg@yahoo.com

    2009-08-01

    Fast neutron radiography opened up a new range of possibilities to image extremely dense objects. The removal of the scattering effect is one of the most challenging problems in neutron imaging. Neutron scattering in fast neutron radiography did not receive much attention compared with X-ray and thermal neutron radiography. The purpose of this work is to investigate the behavior of the Point Scattered Function (PScF) as applied in fast neutron radiography. The PScF was calculated using MCNP as a spatial distribution of scattered neutrons over the detector surface for one emitting source element. Armament and explosives materials, namely, Rifle steel, brass, aluminum and trinitrotoluene (TNT) were simulated. Effect of various sample thickness and sample-to-detector distance were considered. Simulated sample geometries included a slab with varying thickness, a sphere with varying radii, and a cylinder with varying base radii. Different neutron sources, namely, Cf-252, DT as well as DD neutron sources were considered. Neutron beams with zero degree divergence angle; and beams with varying angles related to the normal to the source plane were simulated. Curve fitting of the obtained PScF, in the form of Gaussian function, were given to be used in future work using image restoration codes. Analytical representation of the height as well as the Full Width at Half Maximum (FWHM) of the obtained Gaussian functions eliminates the need to calculate the PScF for sample parameters that were not investigated in this study.

  1. Trichobezoars Detected and Treated Based on Plain Radiography.

    Science.gov (United States)

    Barrows, Amy; Vachon, Tyler; Campin, Richard C; Ignacio, Romeo C

    2015-10-01

    Bezoars are conglomerations of indigestible material that become trapped in the gastrointestinal tract. We present a case of an 8-year-old female child diagnosed with a gastric bezoar solely on plain radiography and treated with abdominal surgical exploration and removal. In addition, traditional characteristic radiographic findings and treatment options for bezoars found in the current literature are reviewed.

  2. Pencil beam proton radiography using a multilayer ionization chamber

    NARCIS (Netherlands)

    Farace, Paolo; Righetto, Roberto; Meijers, Arturs

    2016-01-01

    A pencil beam proton radiography (PR) method, using a commercial multilayer ionization chamber (MLIC) integrated with a treatment planning system (TPS) was developed. A Giraffe (IBA Dosimetry) MLIC (+/- 0.5 mm accuracy) was used to obtain pencil beam PR by delivering spots uniformly positioned at a

  3. Chest radiography and abdominal ultrasound in general practice

    NARCIS (Netherlands)

    Speets, Anouk Mariëlle

    2006-01-01

    Chest radiography (CXR) and abdominal ultrasound (US) are two widely used diagnostic imaging techniques in Western societies. General practitioners (GPs) in The Netherlands annually request approximately 500,000 CXRs and 200,000 abdominal US, and therefore clearly place a burden on health care. Besi

  4. Common positioning errors in panoramic radiography: A review

    Energy Technology Data Exchange (ETDEWEB)

    Randon, Rafael Henrique Nunes [Stomathology and Oral Diagnostic Program, School of Dentistry of Sao Paulo, University of Sao Paulo, Sao Paulo (Brazil); Pereira, Yamba Carla Lara [Biology Dental Buco Graduate Program, School of Dentistry of Piracicaba, University of Campinas, Piracicaba (Brazil); Nascimento, Glauce Crivelaro do [Psychobiology Graduate Program, School of Philosophy, Science and Literature of Ribeirao Preto, University of Sao Paulo, Ribeirao Preto (Brazil)

    2014-03-15

    Professionals performing radiographic examinations are responsible for maintaining optimal image quality for accurate diagnoses. These professionals must competently execute techniques such as film manipulation and processing to minimize patient exposure to radiation. Improper performance by the professional and/or patient may result in a radiographic image of unsatisfactory quality that can also lead to a misdiagnosis and the development of an inadequate treatment plan. Currently, the most commonly performed extraoral examination is panoramic radiography. The invention of panoramic radiography has resulted in improvements in image quality with decreased exposure to radiation and at a low cost. However, this technique requires careful, accurate positioning of the patient's teeth and surrounding maxillofacial bone structure within the focal trough. Therefore, we reviewed the literature for the most common types of positioning errors in panoramic radiography to suggest the correct techniques. We would also discuss how to determine if the most common positioning errors occurred in panoramic radiography, such as in the positioning of the patient's head, tongue, chin, or body.

  5. comparison between sonographic and plain radiography in the ...

    African Journals Online (AJOL)

    hi-tech

    2003-10-10

    Oct 10, 2003 ... Senior Lecturer, Department of Radiology, Makerere University, ... Plain radiography made a diagnosis in 85.5% of patients and did ... abdominal pain, abdominal distension, vomiting and ... major draw back with the use of ultrasound is that it is .... Plain abdominal film demonstrates non-specific gaseous.

  6. Gonad shielding in paediatric pelvic radiography: disadvantages prevail over benefit

    NARCIS (Netherlands)

    Frantzen, M.J.; Robben, S.; Postma, A.A.; Zoetelief, J.; Wildberger, J.E.; Kemerink, G.J.

    2012-01-01

    Objective To re-evaluate gonad shielding in paediatric pelvic radiography in terms of attainable radiation risk reduction and associated loss of diagnostic information. Methods A study on patient dose and the quality of gonad shielding was performed retrospectively using 500 pelvic radiographs of ch

  7. Effect of comfort pads and incubator design on neonatal radiography

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Xia; Baad, Michael; Reiser, Ingrid; Feinstein, Kate A.; Lu, Zhengfeng [University of Chicago Medicine, Department of Radiology, Chicago, IL (United States)

    2016-01-15

    There has been increasing interest in patient dose reduction in neonatal intensive care units. Removing comfort pads for radiography has been identified as a potential means to decrease patient dose. To assess the effect of comfort pads and support trays on detector entrance exposure (DEE) and image quality for neonatal radiography, and its implication for patient dose. Comfort pads and support trays from three incubator and warmer systems were examined. The attenuation of the primary beam by these structures was measured using a narrow beam geometry. Their effect on DEE and image quality was then assessed using typical neonatal chest radiography techniques with three configurations: (1) both the comfort pad and support included in the beam, (2) only the support tray included and (3) both the comfort pad and support tray removed. Comfort pads and support trays were found to attenuate the primary beam by 6-15%. Eliminating these structures from the X-ray beam's path was found to increase the detector entrance exposure by 28-36% and increase contrast-to-noise ratio by more than 21%, suggesting room for patient dose reduction when the same image quality is maintained. Comfort pads and tray support devices can have a considerable effect on DEE and image quality, with large variations among different incubator designs. Positioning the image detector directly underneath neonatal patients for radiography is a potential means for patient dose reduction. However, such benefit should be weighed against the risks of moving the patient. (orig.)

  8. Utility of lead thyroid collar in cephalometric radiography

    Directory of Open Access Journals (Sweden)

    Anuraag B Choudhary

    2012-01-01

    Conclusions : Lead shielding of the thyroid gland does not affect landmark identification or the specific measurements of the angulations traced during cephalometric analysis. TCs should be routinely applied during cephalometric radiography if cephalometric analyses are limited to the structures above the second cervical vertebra.

  9. The value of thyroid shielding in intraoral radiography

    NARCIS (Netherlands)

    Hoogeveen, R.C.; Hazenoot, B.; Sanderink, G.C.H.; Berkhout, W.E.R.

    2016-01-01

    Objectives: To evaluate the utility of the application of a thyroid shield in intraoral radiography when using rectangular collimation. Methods: Experimental data were obtained by measuring the absorbed dose at the position of the thyroid gland in a RANDO® (The Phantom Laboratory, Salem, NY) male ph

  10. Radiography Capabilities for Matter-Radiation Interactions in Extremes

    Energy Technology Data Exchange (ETDEWEB)

    Walstrom, Peter Lowell [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Garnett, Robert William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chapman, Catherine A. B [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Salazar, Harry Richard [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Otoole, Joseph Alfred [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Barber, Ronald L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gomez, Tony Simon [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-04-28

    The Matter-Radiation Interactions in Extremes (MaRIE) experimental facility will be used to discover and design the advanced materials needed to meet 21st century national security and energy security challenges. This new facility will provide the new tools scientists need to develop next-generation materials that will perform predictably and on-demand for currently unattainable lifetimes in extreme environments. The MaRIE facility is based on upgrades to the existing LANSCE 800-MeV proton linac and a new 12-GeV electron linac and associated X-ray FEL to provide simultaneous multiple probe beams, and new experimental areas. In addition to the high-energy photon probe beam, both electron and proton radiography capabilities will be available at the MaRIE facility. Recently, detailed radiography system studies have been performed to develop conceptual layouts of high-magnification electron and proton radiography systems that can meet the experimental requirements for the expected first experiments to be performed at the facility. A description of the radiography systems, their performance requirements, and a proposed facility layout are presented.

  11. Assessment of panoramic radiography as a national oral examination tool: review of the literature

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jin Woo [School of Dentistry, Seoul National University, Seoul (Korea, Republic of)

    2011-03-15

    The purpose of this review is to evaluate the possibility of panoramic radiography as a national oral examination tool. This report was carried out by review of the literatures. Panoramic radiography has sufficient diagnostic accuracy in dental caries, periodontal diseases, and other lesions. Also, the effective dose of panoramic radiography is lower than traditional full-mouth periapical radiography. Panoramic radiography will improve the efficacy of dental examination in national oral examination. However, more studies are required to evaluate the benefit, financial cost, and operation time and also to make selection criteria and quality management program.

  12. Standard practice for digital imaging and communication nondestructive evaluation (DICONDE) for computed radiography (CR) test methods

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 This practice facilitates the interoperability of computed radiography (CR) imaging and data acquisition equipment by specifying image data transfer and archival storage methods in commonly accepted terms. This practice is intended to be used in conjunction with Practice E2339 on Digital Imaging and Communication in Nondestructive Evaluation (DICONDE). Practice E2339 defines an industrial adaptation of the NEMA Standards Publication titled Digital Imaging and Communications in Medicine (DICOM, see http://medical.nema.org), an international standard for image data acquisition, review, storage and archival storage. The goal of Practice E2339, commonly referred to as DICONDE, is to provide a standard that facilitates the display and analysis of NDE results on any system conforming to the DICONDE standard. Toward that end, Practice E2339 provides a data dictionary and a set of information modules that are applicable to all NDE modalities. This practice supplements Practice E2339 by providing information objec...

  13. Effective dose for patient in multimode panoramic radiography

    Energy Technology Data Exchange (ETDEWEB)

    Yasaki, Shiro; Daibo, Motoji [Ohu Univ., Koriyama, Fukushima (Japan). School of Dentistry

    1999-06-01

    In recent years, multimode panoramic radiography has had various functions, such as the auto exposure function, auto focus function (auto function), TMJ radiography and tomogram radiography functions. The purpose of this study was to estimate the effective dose for patients in each mode of the new multimode panoramic radiography (J. MORITA MFG. CORP. Dental Panorama X-ray Apparatus: Veraview Scope X 600). The absorbed doses in important organs involved in the causation of stochastic effects were measured by a thermoluminescent dosimeter using RANDO phantom. The effective doses were calculated using modified tissue weighting factors recommended by the International Commission on Radiological Protection (ICRP) in 1999. The mean field size over skin in typical panoramic and tomographic examinations was about 3% and 0.4% of the total body surface area of 15000 cm{sup 2}. Assuming that the incidence of skin cancer is proportional to the area of skin exposed to ionizing radiation, the tissue weighting factor of skin can be estimated to be about 0.0003 and 0.00004. The estimate in effective dose was lower (5.3 {mu}Sv) in the panoramic auto function mode (an average exposure condition of 69 kV 7 mA) than that (6.5-13.8 {mu}Sv) in the linear tomogram modes. Since the linear tomogram mode requires a scout view, such as standard panoramic radiography, the dose in the linear tomogram mode becomes higher than other modes. A percentage of gonad doses in effective doses was negligible. (author)

  14. National data analysis of general radiography projection method in medical imaging

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jung Su; Seo, Deok Nam; Choi, In Seok [Dept. of Bio-Convergence Engineering, Korea University Graduate School, Seoul (Korea, Republic of); and others

    2014-09-15

    According to database of medical institutions of health insurance review and assessment service in 2013, 1,118 hospitals and clinics have department of radiology in Korea. And there are CT, fluoroscopic and general radiographic equipment in those hospitals. Above all, general radiographic equipment is the most commonly used in the radiology department. And most of the general radiographic equipment are changing the digital radiography system from the film-screen types of the radiography system nowadays. However, most of the digital radiography department are used the film-screen types of the radiography system. Therefore, in this study, we confirmed present conditions of technical items for general radiography used in hospital and research on general radiographic techniques in domestic medical institutions. We analyzed 26 radiography projection method including chest, skull, spine and pelvis which are generally used in the radiography department.

  15. A Study on Development Performance of Shanghai Municipal Creative Industry Park in City Center%上海中心城区市属创意产业园区的发展绩效研究

    Institute of Scientific and Technical Information of China (English)

    王怀; 栾峰

    2013-01-01

      对上海中心城区前4批69家市属创意产业园区,从改造发展和创意集聚两个方面的多项指标展开绩效评价表明,创意产业园区总体发挥了积极促进创意产业集聚发展的作用,创意产业的行业分布呈现出明显地与传统优势产业和现实国家及地区产业紧密相关的特征,空间分布上则呈现出偏离城市公共中心的内城多点集聚的高绩效园区分布特征、苏州河沿线较低绩效的多点分布、黄浦江沿线点状分布等特征。提出应当从国家和地区产业基础和产业发展阶段趋势角度挖掘创意主导部门,以及确保空间政策的灵活性和弹性等建议。%This paper discusses development performance evaluation on the first four group of 69 Shanghai municipal creative industry parks from two aspects of reform development and creative industrial clustering. This paper finds out that the creative industry parks played a positive role on promote creative industry clustering, it also shows that the professional range of creative industry is closely related to the traditional advantageous industries and the current national and regional industry. The spatial distribution of creative industry parks presents that the characteristics of deviating from the urban public center, high performance of inner city pointed agglomeration, low performance of located along the Suzhou River and Huangpu River. This paper puts forward that leading creative industry department should be selected according to national and regional industry basement and the trends of industry development stage, and suggests on an agile and elastic special policy.

  16. Evaluation of Maragheh County Lands in terms of Natural-Environmental and Human Indicators in order to Locate Industrial Centers Using AHP and VIKOR Models

    Directory of Open Access Journals (Sweden)

    Ramin Askarian

    2016-06-01

    Full Text Available The growth of the industry in the form of industrial complex, region, district, pole or town is aphenomenon that has attracted great attention from the beginning of the twentieth century for its critical role in industrial development of the countries around the world and taking advantage of the features and capacities of everyregion.In the present study,in order to find the best place to locate an industrial town, we used 13 diverse natural and human indicators within the scope of the study. At first, we applied the AHP model in the ARC GIS environment to identify the appropriate or inappropriate zonesfor location allocation and the research results indicated that 26224 hectares of the lands in the studied area were perfectly suitable. Next, we utilized the ARC GIS software capabilities to isolate areas over 300 hectares that were suitable for location allocation and we used VIKOR model and 8 basic and important industry locating parameters and prioritized the perfectly fit zones. The research results showed that the current location allocation of the industries is incompatible with the locations proposed in the present study.

  17. Neutron radiography observations of inner wet region in drying of quartz sand cylinder

    Energy Technology Data Exchange (ETDEWEB)

    FijaL-Kirejczyk, I.M. [Institute of Atomic Energy POLATOM, 05-400 Otwock-Swierk (Poland); Milczarek, J.J., E-mail: jjmilcz@cyf.gov.pl [Institute of Atomic Energy POLATOM, 05-400 Otwock-Swierk (Poland); ZoLadek-Nowak, J. [Institute of Atomic Energy POLATOM, 05-400 Otwock-Swierk (Poland)

    2011-09-21

    The drying process of wet quartz sand cylinder was studied with neutron radiography as well as with sample temperature and mass measurements. The constant rate and falling rate periods of the process were clearly identified. During the advanced phase of drying, an inner wet region in the sample center was revealed in the neutron radiographs. The emergence of the inner wet region resulted in marked rise in the standard deviation of the brightness of pixels constituting the sample image. The theoretical analysis of the brightness variations was performed in terms of neutron absorption in dry material matrix and water occupying some of the space between sand grains as well as scattering of neutrons on water. It was found that the inner wet region shrinks in radial direction with time while the apparent water content within it remains constant. The different periods of drying have been attributed to capillary transport at the beginning and vapor flow at advanced stages of the process.

  18. A CONCEPTUAL 3-GEV LANSCE LINAC UPGRADE FOR ENHANCED PROTON RADIOGRAPHY

    Energy Technology Data Exchange (ETDEWEB)

    Garnett, Robert W [Los Alamos National Laboratory; Rybarcyk, Lawrence J. [Los Alamos National Laboratory; Merrill, Frank E. [Los Alamos National Laboratory; O' Hara, James F. [Los Alamos National Laboratory; Rees, Daniel E. [Los Alamos National Laboratory; Walstrom, Peter L. [Los Alamos National Laboratory

    2012-05-14

    A conceptual design of a 3-GeV linac upgrade that would enable enhanced proton radiography at the Los Alamos Neutron Science Center (LANSCE) is presented. The upgrade is based on the use of superconducting accelerating cavities to increase the present LANSCE linac output energy from 800 MeV to 3 GeV. The LANSCE linac currently provides negative hydrogen ion (H{sup -}) and proton (H{sup +}) beams to several user facilities that support Isotope Production, NNSA Stockpile Stewardship, and Basic Energy Science programs. Required changes to the front-end, the accelerating structures, and to the RF systems to meet the new performance goals, and changes to the existing beam switchyard to maintain operations for a robust user program are also described.

  19. Development of automatic system for reducing of occupational exposure dose in Ir-192 radiography

    Energy Technology Data Exchange (ETDEWEB)

    Joo, G. T.; Song, J. H.; Shin, J. S.; Kim, D. E. [Korea Industrial Testing Company, Seoul (Korea, Republic of)

    2003-07-01

    Using Ir-192 gamma source for radiography, it is difficult to reduce occupational exposure and to do quantitative quality control because radiographic test is almost hand-operated and is not improved for a long time in domestic. In this study, a controller with BLDC motor of 24V, 200W which has output of 54 kgf{center_dot}cm and one-chip microprocessor which can control of speed, position and exposure time of Ir-192 gamma source, a remote controller with RF module and a automatic radiation alarm monitor device have been developed. The developed system is predicted that the unit can be in many practical applications with benefits in economical advantage. Also, occupational exposure will be reduced because of remote controller of developed automatic system for Ir-192 radiographic test.

  20. Segmental lumbar spine instability at flexion-extension radiography can be predicted by conventional radiography

    Energy Technology Data Exchange (ETDEWEB)

    Pitkaenen, M.T.; Manninen, H.I.; Lindgren, K.-A.J.; Sihvonen, T.A.; Airaksinen, O.; Soimakallio, S

    2002-07-01

    AIM: To identify plain radiographic findings that predict segmental lumbar spine instability as shown by functional flexion-extension radiography. MATERIALS AND METHODS: Plain radiographs and flexion-extension radiographs of 215 patients with clinically suspected lumbar spine instability were analysed. Instability was classified into anterior or posterior sliding instability. The registered plain radiographic findings were traction spur, spondylarthrosis, arthrosis of facet joints, disc degeneration, retrolisthesis, degenerative spondylolisthesis, spondylolytic spondylolisthesis and vacuum phenomena. Factors reaching statistical significance in univariate analyses (P < 0.05) were included in stepwise multiple logistic regression analysis. RESULTS: Degenerative spondylolisthesis (P = 0.004 at L3-4 level and P = 0.017 at L4-5 level in univariate analysis and odds ratio 16.92 at L4-5 level in multiple logistic regression analyses) and spondylolytic spondylolisthesis (P = 0.003 at L5-S1 level in univariate analyses) were the strongest independent determinants of anterior sliding instability. Retrolisthesis (odds ratio 10.97), traction spur (odds ratio 4.45) and spondylarthrosis (odds ratio 3.20) at L3-4 level were statistically significant determinants of posterior sliding instability in multivariate analysis. CONCLUSION: Sliding instability is strongly associated with various plain radiographic findings. In mechanical back pain, functional flexion-extension radiographs should be limited to situations when symptoms are not explained by findings of plain radiographs and/or when they are likely to alter therapy. Pitkaenen, M.T. et al. (2002)

  1. Advantages obtained in radiation protection when using computerized radiography tests - CR (digital) in processing plants; Vantagens obtidas em radioprotecao quando do uso do ensaio de radiografia computadorizada - RC (digital) em plantas de processo

    Energy Technology Data Exchange (ETDEWEB)

    Jose, Joao Carlos Videira; Milani, Hilton Sergio B.; Paes, Eliseu Almir de Oliveira; Boita, Mario de [ARCtest Servicos Tecnicos de Inspecao e Manutencao Industrial Ltda., Sao Paulo, SP (Brazil)]. E-mail: tecnica@arctest.com.br; Souza, Laercio de; Serra, Flavio Augusto dos Santos [PETROBRAS, Paulinia, SP, RJ (Brazil). Refinaria do Planalto Paulista (REPLAN)]. E-mails: laerciosouza@petrobras.com.br; serra@petrobras.com.br

    2002-07-01

    During the year 2000, the ARCtest initiated the development of the research for adapting the Computerized Radiography - CR, originally conceived for medical applications, for the Industry, trying initially to attend the requirements of the processing plants, concerning to the detection of deterioration mechanisms (evaluation of the piping integrity). Due to the obtained excellent results, the possibility of utilization the Computerized Radiography - CR in the radiographic inspection were studied during the shutdown of the Catalytic Cracking Unit of the PETROBRAS-REPLAN, specifically in the replacement of the CO boiler superheater, where a large number of the small diameter welded joints have been predicted.

  2. On External Public Space Design of Cultural and Creative Industry Center:A Case Study of Nanjing Creative Center%文化创意产业园外部公共空间的营造--以南京创意中央为例

    Institute of Scientific and Technical Information of China (English)

    杨艺红; 于璐

    2015-01-01

    As a new type of emerging industry, creative industry has become an integral part of the urban industrial structure. Cultural and creative industry center, an important carrier of creative industry, has developed rapidly in China. External public space, the carrier of the transportation and creative exchange, plays an indispensible role in creative industry center through providing room for rest, creation and interaction of the creative group. Meanwhile, working habits and lifestyles of the users of cultural and creative industry center define the importance of public space design in the industry center planning. Currently, the design of external public space in line with the using characteristics, site features and distinctive functions of the industry center has become an important factor to make sustainable development of cultural and creative industry center. Taking Nanjing Creative Center as the research object and focusing on the uniqueness of cultural and creative industry center and the creative group, this paper studied the components of the external public space of creative industry center through the introduction to Jan Gail ’s theory of communication and space. By means of analyzing traffic structure and space joint mode in the Center, the paper probed into the designing and constructing of external public space of the Center. All these findings will give beneficial references for external public space design of cultural and creative industry centers and provide theoretical guidance for the establishment of brand and characteristics to achieve coordinated and sound development.%创意产业作为一种新兴产业类型,已经成为城市产业结构不可或缺的一部分。文化创意产业园作为其发展的重要载体,在我国发展迅猛。外部公共空间作为创意产业园中交通、创意交流的载体,创意阶层休憩、创作、交往的主要承担者,在创意产业园中扮演着不可或缺的角色,同时创意

  3. Dose in conventional radiography; Dosis en radiografia convencional

    Energy Technology Data Exchange (ETDEWEB)

    Acuna D, E.; Padilla R, Z. P.; Escareno J, E.; Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Calle Cipres No. 10, Fracc. La Penuela, 98000 Zacatecas (Mexico)

    2011-10-15

    It has been pointed out that medical exposures are the most significant sources of exposure to ionizing radiation for the general population. Inside the medical exposures the most important is the X-ray use for diagnosis, which is by far the largest contribution to the average dose received by the population. From all studies performed in radiology the chest radiography is the most abundant. In an X-ray machine, voltage and current are combined to obtain a good image and a reduce dose, however due to the workload in a radiology service individual dose is not monitored. In order to evaluate the dose due to chest radiography in this work a plate phantom was built according to the ISO recommendations using methylmethacrylate walls and water. The phantom was used in the Imaging department of the Zacatecas General Hospital as a radiology patient asking for a chest study; using thermoluminescent dosimeters, TLD 100 the kerma at the surface entrance was determined. (Author)

  4. Computer-aided diagnosis in chest radiography: Beyond nodules

    Energy Technology Data Exchange (ETDEWEB)

    Ginneken, Bram van [University Medical Center Utrecht, Heidelberglaan 100, 3584 CX Utrecht (Netherlands)], E-mail: bram@isi.uu.nl; Hogeweg, Laurens; Prokop, Mathias [University Medical Center Utrecht, Heidelberglaan 100, 3584 CX Utrecht (Netherlands)

    2009-11-15

    Chest radiographs are the most common exam in radiology. They are essential for the management of various diseases associated with high mortality and morbidity and display a wide range of findings, many of them subtle. In this survey we identify a number of areas beyond pulmonary nodules that could benefit from computer-aided detection and diagnosis (CAD) in chest radiography. These include interstitial infiltrates, catheter tip detection, size measurements, detection of pneumothorax and detection and quantification of emphysema. Recent work in these areas is surveyed, but we conclude that the amount of research devoted to these topics is modest. Reasons for the slow pace of CAD development in chest radiography beyond nodules are discussed.

  5. Application of imaging plate neutron detector to neutron radiography

    CERN Document Server

    Fujine, S; Kamata, M; Etoh, M

    1999-01-01

    As an imaging plate neutron detector (IP-ND) has been available for thermal neutron radiography (TNR) which has high resolution, high sensitivity and wide range, some basic characteristics of the IP-ND system were measured at the E-2 facility of the KUR. After basic performances of the IP were studied, images with high quality were obtained at a neutron fluence of 2 to 7x10 sup 8 n cm sup - sup 2. It was found that the IP-ND system with Gd sub 2 O sub 3 as a neutron converter material has a higher sensitivity to gamma-ray than that of a conventional film method. As a successful example, clear radiographs of the flat view for the fuel side plates with boron burnable poison were obtained. An application of the IP-ND system to neutron radiography (NR) is presented in this paper.

  6. A new scanner for in situ digital radiography of paintings

    Science.gov (United States)

    Impallaria, Anna; Evangelisti, Federico; Petrucci, Ferruccio; Tisato, Flavia; Castelli, Lisa; Taccetti, Francesco

    2016-12-01

    X-ray radiography is one of the most widely used imaging techniques in the field of cultural heritage, both for conservation and for investigation purposes. Performing radiographies in museums, thus avoiding movements of works of art, has been recently made easy by digital acquisition of images, but when the whole scan of a large painting is required, technical solutions for a portable device are still not at hand. The inherent weight of the X-ray tube and of the high-voltage generator makes the design of a portable device very difficult. In this project, the solution of the puzzle was separating devices devoted to different tasks, in order to maintain each item under 60 kg weight, thus being transportable with reasonable effort.

  7. The MU-RAY detector for muon radiography of volcanoes

    Energy Technology Data Exchange (ETDEWEB)

    Anastasio, A. [INFN-Napoli (Italy); Ambrosino, F. [INFN-Napoli (Italy); Università Federico II, Napoli (Italy); Basta, D. [INFN-Napoli (Italy); Bonechi, L. [Università degli Studi di Firenze, Firenze (Italy); INFN-Firenze (Italy); Brianzi, M. [Università degli Studi di Firenze, Firenze (Italy); Bross, A. [Fermilab (United States); Callier, S. [LAL, Orsay (France); Caputo, A. [INGV Osservatorio Vesuviano, Napoli (Italy); Ciaranfi, R. [INFN-Firenze (Italy); Cimmino, L. [INFN-Napoli (Italy); Università Federico II, Napoli (Italy); D' Alessandro, R. [Università degli Studi di Firenze, Firenze (Italy); INFN-Firenze (Italy); D' Auria, L. [INGV Osservatorio Vesuviano, Napoli (Italy); La Taille, C. de [LAL, Orsay (France); Energico, S. [CNR- SPIN, Napoli (Italy); INFN-Napoli (Italy); Garufi, F. [INFN-Napoli (Italy); Università Federico II, Napoli (Italy); Giudicepietro, F. [INGV Osservatorio Vesuviano, Napoli (Italy); Lauria, A. [INFN-Napoli (Italy); Università Federico II, Napoli (Italy); Macedonio, G.; Martini, M. [INGV Osservatorio Vesuviano, Napoli (Italy); Masone, V. [Università Federico II, Napoli (Italy); and others

    2013-12-21

    The MU-RAY detector has been designed to perform muon radiography of volcanoes. The possible use on the field introduces several constraints. First the electric power consumption must be reduced to the minimum, so that the detector can be solar-powered. Moreover it must be robust and transportable, for what concerns the front-end electronics and data acquisition. A 1 m{sup 2} prototype has been constructed and is taking data at Mt. Vesuvius. The detector consists of modules of 32 scintillator bars with wave length shifting fibers and silicon photomultiplier read-out. A dedicated front-end electronics has been developed, based on the SPIROC ASIC. An introduction to muon radiography principles, the MU-RAY detector description and results obtained in laboratory will be presented.

  8. Proton radiography and tomography with application to proton therapy

    Science.gov (United States)

    Allinson, N M; Evans, P M

    2015-01-01

    Proton radiography and tomography have long promised benefit for proton therapy. Their first suggestion was in the early 1960s and the first published proton radiographs and CT images appeared in the late 1960s and 1970s, respectively. More than just providing anatomical images, proton transmission imaging provides the potential for the more accurate estimation of stopping-power ratio inside a patient and hence improved treatment planning and verification. With the recent explosion in growth of clinical proton therapy facilities, the time is perhaps ripe for the imaging modality to come to the fore. Yet many technical challenges remain to be solved before proton CT scanners become commonplace in the clinic. Research and development in this field is currently more active than at any time with several prototype designs emerging. This review introduces the principles of proton radiography and tomography, their historical developments, the raft of modern prototype systems and the primary design issues. PMID:26043157

  9. Advancement of neutron radiography technique in JRR-3M

    Energy Technology Data Exchange (ETDEWEB)

    Matsubayashi, Masahito [Center for Neutron Science, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan)

    1999-08-01

    The JRR-3M thermal neutron radiography facility (JRR-3M TNRF) was completed in the JRR-3M of the Japan Atomic Energy Research Institute in 1991 and has been utilized as research tools for various kinds of research fields such as thermal hydraulic researches, agricultural researches, medical researches, archaeological researches and so on. High performance of the JRR-3M TNRF such as high neutron flux, high collimator ratio and wide radiographing field has enabled advanced researches and stimulated developments of advanced neutron radiography (NR) systems for higher spatial resolution and for higher temporal resolution. Static NR systems using neutron imaging plates or cooled CCD camera with high spatial resolution, a real-time NR system using a silicon intensifier target tube camera and a high-frame-rate NR system using a combination of an image intensifier and a high speed digital video camera with high temporal resolution have been developed to fill the requirements from researchers. (author)

  10. Diagnostic ability of panoramic radiography for mandibular fractures

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ji Hyun; Jung, Yun Hoa; Cho Bong Hae; Hwang, Dae Seok [School of Dentistry, Pusan National University, Pusan (Korea, Republic of)

    2010-03-15

    The purpose of this study was to evaluate the diagnostic efficacy of panoramic radiographs for detection of mandibular fractures. The sample was comprised of 65 patients (55 fractured, 10 non-fractured) with 92 fracture sites confirmed by multi-detector computed tomography (CT). Panoramic radiographs were evaluated for mandibular fractures by six examiners; two oral and maxillofacial radiologists (observer A and B), two oral and maxillofacial surgeons (observer C and D), and two general dentists (observer E and F). Sensitivity of panoramic radiography for mandibular fractures was 95.7% in observer A and B, 93.5% in observer C and D and 80.4% in observer E and F. The lowest sensitivity was shown in symphyseal/parasymphyseal areas, followed by subcondylar/condylar regions. Panoramic radiography is adequate for detection of mandibular fractures. However, additional multidetector CT is recommended to ascertain some indecisive fractures of symphysis and condyle, and in complicated fractures.

  11. Digital radiography: update for oral health care workers.

    Science.gov (United States)

    Noffke, C E E; Nzima, N; Chabikuli, N J

    2004-08-01

    Digital Radiography is an imaging system that does away with the use of films. It constitutes an advance in computer technology and has made a significant impact on the field of Maxillofacial- and Dental Radiology. This paper presents an overview of the basic concepts and applications of dental digital radiography and compares it with conventional film-based imaging. In addition, it provides a thorough understanding of the direct, semi-direct and indirect dental digital imaging systems with their advantages and disadvantages. Universal acceptance of digital radiographic imaging as a diagnostic tool makes it important for oral health care workers to understand the principles thereof and to master the techniques involved in acquiring a diagnosable digital radiographic image.

  12. First results on proton radiography with nuclear emulsion detectors

    CERN Document Server

    Braccini, S; Kreslo, I; Moser, U; Pistillo, C; Studer, S; Scampoli, P; Coray, A; Pedroni, E

    2010-01-01

    We propose an innovative method for proton radiography based on nuclear emulsion film detectors, a technique in which images are obtained by measuring the position and the residual range of protons passing through the patient's body. For this purpose, nuclear emulsion films interleaved with tissue equivalent absorbers can be used to reconstruct proton tracks with very high accuracy. This is performed through a fully automated scanning procedure employing optical microscopy, routinely used in neutrino physics experiments. Proton radiography can be used in proton therapy to obtain direct information on the average tissue density for treatment planning optimization and to perform imaging with very low dose to the patient. The first prototype of a nuclear emulsion based detector has been conceived, constructed and tested with a therapeutic proton beam. The first promising experimental results have been obtained by imaging simple phantoms.

  13. A new scanner for in situ digital radiography of paintings

    Energy Technology Data Exchange (ETDEWEB)

    Impallaria, Anna; Petrucci, Ferruccio; Tisato, Flavia [University of Ferrara, Department of Physics and Earth Science, Ferrara (Italy); TekneHub Ferrara, Ferrara (Italy); INFN-Sezione di Ferrara, Ferrara (Italy); Evangelisti, Federico [University of Ferrara, Department of Physics and Earth Science, Ferrara (Italy); INFN-Sezione di Ferrara, Ferrara (Italy); Castelli, Lisa; Taccetti, Francesco [INFN-Sezione di Firenze, Sesto Fiorentino (Italy)

    2016-12-15

    X-ray radiography is one of the most widely used imaging techniques in the field of cultural heritage, both for conservation and for investigation purposes. Performing radiographies in museums, thus avoiding movements of works of art, has been recently made easy by digital acquisition of images, but when the whole scan of a large painting is required, technical solutions for a portable device are still not at hand. The inherent weight of the X-ray tube and of the high-voltage generator makes the design of a portable device very difficult. In this project, the solution of the puzzle was separating devices devoted to different tasks, in order to maintain each item under 60 kg weight, thus being transportable with reasonable effort. (orig.)

  14. Developing the profession of radiography: Making use of oral history

    Energy Technology Data Exchange (ETDEWEB)

    Decker, Sola [School of Radiography, Faculty of Nursing, Midwifery and Health Studies, University of Wales, Bangor, Archimedes Centre, Technology Park, Wrexham LL13 7YP (United Kingdom)]. E-mail: rdsa01@bangor.ac.uk; Iphofen, Ron [Faculty of Nursing, Midwifery and Health Studies, University of Wales, Bangor, Archimedes Centre, Technology Park, Wrexham LL13 7YP (United Kingdom)

    2005-11-01

    This paper is based on ongoing research into the profession of radiography using the oral history method. Knowledge of radiographic practice as a profession has in the past been based on what is written or learnt from other professions both within and beyond the field of health care. The profession has experienced substantial technological and sociological changes both in training and in practice over the past few decades and these look set to continue into the immediate future. Evidence-based practice is invoked as a quality measure on all health professions, and part of the body of knowledge which forms the evidence base of practice development involves an understanding of how the profession has responded to change and what this might mean for the further changes it is likely to meet. This paper explores the potential role of oral history research as a tool for the development of knowledge about the practice of radiography.

  15. Turnover Rate Simulation Using GEM Detector on Neutron Radiography

    Institute of Scientific and Technical Information of China (English)

    SHAN; Chao; LI; Xiao-mei; HU; Shou-yang; ZHOU; Jing; JIAN; Si-yu; BAI; Xin-zhan; YE; Li; ZHOU; Shu-hua

    2012-01-01

    <正>With the advantages of high counting rate, high resolution ratio and high compatibility, GEM (Gas Electron Multiplier) detector has becoming the hot topic in the field of gas detector. Using GEM on neutron radiography, we need a suitable neutron converter. By the action on the converter and ingoing neutron, the outgoing particles could be an alpha or proton, which are charged particles. The charged

  16. Subtraction Radiography for the Diagnosis of Bone Lesions in Dogs.

    Science.gov (United States)

    1984-05-31

    Avail ander Journal of Periodontology Dist Special Ř 211 East Chicago Avenue Room 924 Chicago, IL 60611 Dear Sirs: I m submitting an original...research article titled "Subtraction Radiography for the Diagnosis of Bone Lesions in Dogs" solely to the Journal of Periodontology for review and... clinical practice in our area. 60-70 Kvp would have produced more contrast in the radiographic films used for the conventional technique, but likely

  17. Absorbed radiation by various tissues during simulated endodontic radiography

    Energy Technology Data Exchange (ETDEWEB)

    Torabinejad, M.; Danforth, R.; Andrews, K.; Chan, C.

    1989-06-01

    The amount of absorbed radiation by various organs was determined by placing lithium fluoride thermoluminescent chip dosimeters at selected anatomical sites in and on a human-like X-ray phantom and exposing them to radiation at 70- and 90-kV X-ray peaks during simulated endodontic radiography. The mean exposure dose was determined for each anatomical site. The results show that endodontic X-ray doses received by patients are low when compared with other radiographic procedures.

  18. Development of imaging techniques for fast neutron radiography in Japan

    CERN Document Server

    Fujine, S; Yoshii, K; Kamata, M; Tamaki, M; Ohkubo, K; Ikeda, Y; Kobayashi, H

    1999-01-01

    Neutron radiography with fast neutron beams (FNR) has been studied at the fast neutron source reactor 'YAYOI' of the University of Tokyo since 1986. Imaging techniques for FNR have been developed for CR-39 track-etch detector, electronic imaging system (television method), direct film method, imaging plate and also fast and thermal neutron concurrent imaging method. The review of FNR imaging techniques and some applications are reported in this paper.

  19. Real-time radiography at the NECTAR facility

    Energy Technology Data Exchange (ETDEWEB)

    Buecherl, T., E-mail: thomas.buecherl@radiochemie.de [Lehrstuhl fuer Radiochemie (RCM), Technische Universitaet Muenchen (TUM), Walther-Meissner-Str. 3, 85748 Garching (Germany); Lierse von Gostomski, Ch. [Lehrstuhl fuer Radiochemie (RCM), Technische Universitaet Muenchen (TUM), Walther-Meissner-Str. 3, 85748 Garching (Germany)

    2011-09-21

    A feasibility study has shown that real-time radiography using fission neutrons is possible at the NECTAR facility, when using an improved detection system for fast variations (Buecherl et al., 2009 ). Continuing this study, real-time measurements of slowly varying processes like the water uptake in medium sized trunks (diameter about 12 cm) and of slow periodic processes (e.g. a slowly rotating iron disk) are investigated successfully using the existing detection system.

  20. Dose Reduction to the Thyroid Gland in Pediatric Chest Radiography

    Directory of Open Access Journals (Sweden)

    Vahid Karami

    2016-07-01

    Full Text Available Background  It is remain a main concern that pediatric chest radiographies contribute to the significant radiation exposure to the thyroid gland as a more susceptible organ to radiation induced cancer. The aim of this study was to evaluate the entrance surface dose (ESD of pediatric chest radiography compared to the diagnostic reference levels (DRL and evaluation the efficacy of the lead (Pb shield in radiation dose reduction to the thyroid gland.Materials and Methods After assessing each patient against specific inclusion-exclusion criteria, 40 pediatric patients who were undergoing anterior-posterior (AP projection of the chest x-ray were considered eligible for this study. The ESD of the chest and also ESD of thyroid gland with and without a 1 mm butterfly-shaped lead shield which placed on the thyroid gland were measured using high sensitive thermo luminescent dosimeters (TLD-GR 200.Results The average of ESD for chest radiography was 0.068+ 0.006 mGy (0.021 - 0.232 mGy. The unshielded average thyroid ESD was 0.065 + 0.003 mGy compared to the shielded average thyroid ESD of 0.001 + 0.0005 mGy. The use of Pb-shield produced a statistically significant decrease in the average thyroid dose by about 97% (P< 0.001. Conclusion The use of Pb-thyroid shield in the AP projection of pediatric chest radiography has potential to reduced radiation dose without compromising image quality.

  1. Practical guidelines for radiographers to improve computed radiography image quality

    OpenAIRE

    Pongnapang, N

    2005-01-01

    Computed Radiography (CR) has become a major digital imaging modality in a modern radiological department. CR system changes workflow from the conventional way of using film/screen by employing photostimulable phosphor plate technology. This results in the changing perspectives of technical, artefacts and quality control issues in radiology departments. Guidelines for better image quality in digital medical enterprise include professional guidelines for users and the quality control programme...

  2. ADVANCEMENTS IN NEUTRON RADIOGRAPHY WITHIN THE DEPARTMENT OF THE ARMY

    Science.gov (United States)

    2016-11-01

    Carlo N-particle (MCNP) simulation software. The modeling confirmed that acceptable dose rates would be achieved outside of the shooting cell and...advanced nondestructive testing (NDT) technologies and inspections. Within the past five years, neutron radiography (NR) has been a main focus of...development where previous commercial off the shelf systems were inadequate to use. An increase in inspection technology was desired due to the rising need

  3. 北京建设国际商贸中心与物流业发展研究%The research on Beijing's logistics industry development and making Beijing as the world business center

    Institute of Scientific and Technical Information of China (English)

    赵淼

    2012-01-01

    加快国际商贸中心建设是北京建设世界城市的重要举措之一。建设国际商贸中心,需要发达的商贸业,并形成多层次的商贸流通体系,因而物流业的发展就具有举足轻重的作用。本文通过分析北京与世界城市在商贸流通方面的差距及其发展物流业的客观需求,进而提出了北京在建设国际商贸中心过程中加快发展物流业的对策建议。%Being an important embodiment of a world cities,the construction of an international commerce and trade center plays a leading role in world business cities' development.Building Beijing as an international trade center will accelerate the pace towards world cities.The formation of the international commerce and trade center originated from the internationalization of the city exchange function,and its influence and radiation force mainly depends on the commercial and trade circulation.Therefore,it has practical significance for Beijing's construction of a world city to research on Beijing's logistics industry development demand.The paper put forward some suggestions on the speeding up of the capital's logistics industry development on the bases of the gaps between China's capital and other business big cities in the world and the practical demand of logistics industry of Beijing.

  4. Thoracic radiography and oxidative stress indices in heartworm affected dogs

    Directory of Open Access Journals (Sweden)

    P. K. Rath

    2014-09-01

    Full Text Available Aim: The aim was to study the pathomorphological changes through thoracic radiography and status of oxidative stress parameters in heartworm affected dogs in Odisha. Materials and Methods: A total of 16 dogs with clinically established diagnosis of dirofilariasis by wet blood smear and modified Knott’s test and equal numbers of dogs as control were included in this study. The present study was conducted in heartworm affected dogs to see the pathomorphological changes through thoracic radiography. Similarly, the evaluation was undertaken for observing any alterations in oxidative stress status in affected as well as non-affected, but healthy control dogs by adopting standard procedure. Results: Thoracic radiography revealed cardiac enlargement, round heart appearance suggestive of right ventricular hypertrophy, tortuous pulmonary artery and darkening of lungs. Alterations in oxidative stress indices showed a significant rise of lipid peroxidase activity, non-significant rise of superoxide dismutase and a significant although reverse trend for catalase levels in affected dogs in comparison to Dirofilaria negative control but apparently healthy dogs. Conclusions: Radiographic changes, as well as alterations in oxidative stress parameters, may not be diagnostic for heartworm infection, but useful for detecting heartworm disease, assessing severity and evaluating cardiopulmonary parenchyma changes and gives a fair idea about the degree of severity of the disease. It aids as contributing factors in disease pathogenesis.

  5. Practical contour segmentation algorithm for small animal digital radiography image

    Science.gov (United States)

    Zheng, Fang; Hui, Gong

    2008-12-01

    In this paper a practical, automated contour segmentation technique for digital radiography image is described. Digital radiography is an imaging mode based on the penetrability of x-ray. Unlike reflection imaging mode such as visible light camera, the pixel brightness represents the summation of the attenuations on the photon thoroughfare. It is not chromophotograph but gray scale picture. Contour extraction is of great importance in medical applications, especially in non-destructive inspection. Manual segmentation techniques include pixel selection, geometrical boundary selection and tracing. But it relies heavily on the experience of the operators, and is time-consuming. Some researchers try to find contours from the intensity jumping characters around them. However these characters also exist in the juncture of bone and soft tissue. The practical way is back to the primordial threshold algorithm. This research emphasizes on how to find the optimal threshold. A high resolution digital radiography system is used to provide the oriental gray scale image. A mouse is applied as the sample of this paper to show the feasibility of the algorithm.

  6. Z-petawatt driven ion beam radiography development.

    Energy Technology Data Exchange (ETDEWEB)

    Schollmeier, Marius; Geissel, Matthias; Rambo, Patrick K.; Schwarz, Jens; Sefkow, Adam B.

    2013-09-01

    Laser-driven proton radiography provides electromagnetic field mapping with high spatiotemporal resolution, and has been applied to many laser-driven High Energy Density Physics (HEDP) experiments. Our report addresses key questions about the feasibility of ion radiography at the Z-Accelerator (%E2%80%9CZ%E2%80%9D), concerning laser configuration, hardware, and radiation background. Charged particle tracking revealed that radiography at Z requires GeV scale protons, which is out of reach for existing and near-future laser systems. However, it might be possible to perform proton deflectometry to detect magnetic flux compression in the fringe field region of a magnetized liner inertial fusion experiment. Experiments with the Z-Petawatt laser to enhance proton yield and energy showed an unexpected scaling with target thickness. Full-scale, 3D radiation-hydrodynamics simulations, coupled to fully explicit and kinetic 2D particle-in-cell simulations running for over 10 ps, explain the scaling by a complex interplay of laser prepulse, preplasma, and ps-scale temporal rising edge of the laser.

  7. Assessment of Nugget Size of Spot Weld using Neutron Radiography

    Directory of Open Access Journals (Sweden)

    Triyono

    2011-08-01

    Full Text Available Resistance spot welding (RSW has been widely used for many years in the fabrication of car body structures, mainly due to the cost and time considerations. The weld quality as well as the nugget size is an issue in various manufacturing and processes due to the strong link between the weld quality and safety. It has led to the development of various destructive and non-destructive tests for spot welding such as peel testing, ultrasonic inspections, digital shearography, and infrared thermography. However, such methods cannot show spot weld nugget visually and the results are very operator’s skill dependent. The present work proposes a method to visualize the nugget size of spot welds using neutron radiography. Water, oil and various concentrations of gadolinium oxide-alcohol mixture were evaluated as a contrast media to obtain the best quality of radiography. Results show that mixture of 5 g gadolinium oxide (Gd2O3 in 25 ml alcohol produces the best contrast. It provides the possibility to visualize the shape and size of the nugget spot weld. Furthermore, it can discriminate between nugget and corona bond. The result of neutron radiography evaluation shows reasonable agreement with that of destructive test.

  8. Radiation dose estimation of patients undergoing lumbar spine radiography

    Directory of Open Access Journals (Sweden)

    Prince Kwabena Gyekye

    2013-01-01

    Full Text Available Radiation dose to organs of 100 adult patients undergoing lumbar spine (LS radiography at a University Hospital have been assessed. Free in air kerma measurement using an ionization chamber was used for the patient dosimetry. Organ and effective dose to the patients were estimated using PCXMC (version 1.5 software. The organs that recorded significant dose due to LS radiography were lungs, stomach, liver, adrenals, kidney, pancreas, spleen, galbladder, and the heart. It was observed that the stomach recorded the highest dose (48.2 ± 1.2 μGy for LS anteroposterior (AP. The spleen also recorded the highest dose (41.2 ± 0.5 μGy for LS lateral (LAT. The mean entrance surface air kerma (ESAK of LS LAT (122.2 μGy was approximately twice that of LS AP (76.3 μGy, but the effective dose for both examinations were approximately the same (LS LAT = 8.6 μSv and LS AP = 10.4 μSv. The overall stochastic health effect of radiation to patients due to LS radiography in the University Hospital is independent of the projection of the examination (AP or LAT.

  9. [Plain-film radiography in the study of spinal pain].

    Science.gov (United States)

    Ruiz Santiago, F; Guzmán Alvarez, L; Tello Moreno, M; Navarrete González, P J

    2010-01-01

    The introduction of tomographic imaging techniques, fundamentally computed tomography and magnetic resonance imaging, has led to a gradual decrease in the indications for plain-film radiography, resulting in fewer patients studied and fewer projections for each patient. Consequently, plain-film studies of the spine have received less attention and radiologists are less familiar with the typical findings in normal and pathologic conditions of the spine. Nevertheless, plain-film radiography continues to be widely used in both primary and specialized care. Thus, radiologists still need to be aware of the normal radiologic anatomy of the spine and of the radiologic manifestations of the diverse pathological processes that can affect the spinal column and that can cause pain. The aim of this article is to review the manifestations on plain-film radiography of a wide variety of diseases that can cause back pain, including congenital, traumatic, degenerative, tumor-related, inflammatory, and infectious diseases and processes. Copyright 2009 SERAM. Published by Elsevier Espana. All rights reserved.

  10. Digital radiography and advanced imaging techniques in dentistry

    Directory of Open Access Journals (Sweden)

    Burcu Keles Evlice

    2013-04-01

    Full Text Available Since the discovery of x-rays in 1895, film has been the primary medium for capturing, displaying and storing radiographic images. Digital or filmless radiography is slowly being adopted by the dental profession. Digital radiography offers a number of capabilities compared with conventional radiography, such as postprocessing, electronic archiving, concurrent access to images, and improved data distribution. Computer based applications which are used for quantitative measurements and evaluations on digital images for better user interpretation. New diagnostic imaging processes are improved connected with the technological progress of computer systems. Since the first clinical use of computed tomography (CT scans in 1972, technological development has been rapid. Dental volumetric tomography (DVT, uniquely used for dentomaxillofacial imaging came to the market owing to recent rapid developments in digital radiology technology and is becoming more popular in dental applications. Low radiation dose cone beam computed tomography (CBCT units that are commercially available at a lower cost than CT units, has performed valuable diagnostic information for dentists. [Archives Medical Review Journal 2013; 22(2.000: 230-238

  11. Management of pediatric radiation dose using Agfa computed radiography

    Energy Technology Data Exchange (ETDEWEB)

    Schaetzing, R. [Agfa Corp., Greenville, SC (United States)

    2004-10-01

    Radiation dose to patients and its management have become important considerations in modern radiographic imaging procedures, but they acquire particular significance in the imaging of children. Because of their longer life expectancy, children exposed to radiation are thought to have a significantly increased risk of radiation-related late sequelae compared to adults first exposed to radiation later in life. Therefore, current clinical thinking dictates that dose in pediatric radiography be minimized, while simultaneously ensuring sufficient diagnostic information in the image, and reducing the need for repeat exposures. Dose management obviously starts with characterization and control of the exposure technique. However, it extends farther through the imaging chain to the acquisition system, and even to the image processing techniques used to optimize acquired images for display. Further, other factors, such as quality control procedures and the ability to handle special pediatric procedures, like scoliosis exams, also come into play. The need for dose management in modern radiography systems has spawned a variety of different solutions, some of which are similar across different manufacturers, and some of which are unique. This paper covers the techniques used in Agfa Computed Radiography (CR) systems to manage dose in a pediatric environment. (orig.)

  12. Marginal Assessment of Crowns by the Aid of Parallel Radiography

    Directory of Open Access Journals (Sweden)

    Farnaz Fattahi

    2015-03-01

    Full Text Available Introduction: Marginal adaptation is the most critical item in long-term prognosis of single crowns. This study aimed to assess the marginal quality as well asthe discrepancies in marginal integrity of some PFM single crowns of posterior teeth by employing parallel radiography in Shiraz Dental School, Shiraz, Iran. Methods: In this descriptive study, parallel radiographies were taken from 200 fabricated PFM single crowns of posterior teeth after cementation and before discharging the patient. To calculate the magnification of the images, a metallic sphere with the thickness of 4 mm was placed in the direction of the crown margin on the occlusal surface. Thereafter, the horizontal and vertical space between the crown margins, the margin of preparations and also the vertical space between the crown margin and the bone crest were measured by using digital radiological software. Results: Analysis of data by descriptive statistics revealed that 75.5% and 60% of the cases had more than the acceptable space (50µm in the vertical (130±20µm and horizontal (90±15µm dimensions, respectively. Moreover, 85% of patients were found to have either horizontal or vertical gap. In 77% of cases, the margins of crowns invaded the biologic width in the mesial and 70% in distal surfaces. Conclusion: Parallel radiography can be expedient in the stage of framework try-in to yield some important information that cannot be obtained by routine clinical evaluations and may improve the treatment prognosis

  13. Advances in computed radiography systems and their physical imaging characteristics.

    Science.gov (United States)

    Cowen, A R; Davies, A G; Kengyelics, S M

    2007-12-01

    Radiological imaging is progressing towards an all-digital future, across the spectrum of medical imaging techniques. Computed radiography (CR) has provided a ready pathway from screen film to digital radiography and a convenient entry point to PACS. This review briefly revisits the principles of modern CR systems and their physical imaging characteristics. Wide dynamic range and digital image enhancement are well-established benefits of CR, which lend themselves to improved image presentation and reduced rates of repeat exposures. However, in its original form CR offered limited scope for reducing the radiation dose per radiographic exposure, compared with screen film. Recent innovations in CR, including the use of dual-sided image readout and channelled storage phosphor have eased these concerns. For example, introduction of these technologies has improved detective quantum efficiency (DQE) by approximately 50 and 100%, respectively, compared with standard CR. As a result CR currently affords greater scope for reducing patient dose, and provides a more substantive challenge to the new solid-state, flat-panel, digital radiography detectors.

  14. Digital contrast subtraction radiography for proximal caries diagnosis

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Byung Cheol; Yoon, Suk Ja [Department of Dental Radiology, Chonnam National University Hospital, Gwangju (Korea, Republic of)

    2002-06-15

    To determine whether subtraction images utilizing contrast media can improve the diagnostic performance of proximal caries diagnosis compared to conventional periapical radiographic images. Thirty-six teeth with 57 proximal surfaces were radiographied using a size no.2 RVG-ui sensor (Trophy Radiology, Marne-la-Vallee, France). The teeth immersed in water-soluble contrast media and subtraction images were taken. Each tooth was then sectioned for histologic examination. The digital radiographic images and subtraction images were examined and interpreted by three dentists for proximal caries. The results of the proximal caries diagnosis were then verified with the results of the histologic examination. The proximal caries sensitivity using digital subtraction radiography was significantly higher than simply examining a single digital radiograph. The sensitivity of the proximal dentinal carious lesion when analyzed with the subtraction radiograph and the radiograph together was higher than with the subtraction radiograph or the radiograph alone. The use of subtraction radiography with contrast media may be useful for detecting proximal dentinal carious lesions.

  15. Energy efficient data centers

    Energy Technology Data Exchange (ETDEWEB)

    Tschudi, William; Xu, Tengfang; Sartor, Dale; Koomey, Jon; Nordman, Bruce; Sezgen, Osman

    2004-03-30

    Data Center facilities, prevalent in many industries and institutions are essential to California's economy. Energy intensive data centers are crucial to California's industries, and many other institutions (such as universities) in the state, and they play an important role in the constantly evolving communications industry. To better understand the impact of the energy requirements and energy efficiency improvement potential in these facilities, the California Energy Commission's PIER Industrial Program initiated this project with two primary focus areas: First, to characterize current data center electricity use; and secondly, to develop a research ''roadmap'' defining and prioritizing possible future public interest research and deployment efforts that would improve energy efficiency. Although there are many opinions concerning the energy intensity of data centers and the aggregate effect on California's electrical power systems, there is very little publicly available information. Through this project, actual energy consumption at its end use was measured in a number of data centers. This benchmark data was documented in case study reports, along with site-specific energy efficiency recommendations. Additionally, other data center energy benchmarks were obtained through synergistic projects, prior PG&E studies, and industry contacts. In total, energy benchmarks for sixteen data centers were obtained. For this project, a broad definition of ''data center'' was adopted which included internet hosting, corporate, institutional, governmental, educational and other miscellaneous data centers. Typically these facilities require specialized infrastructure to provide high quality power and cooling for IT equipment. All of these data center types were considered in the development of an estimate of the total power consumption in California. Finally, a research ''roadmap'' was developed

  16. Hong Kong's Foundry Industry Survey

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ Hong Kong, as one of the global economy centers, its manufacturing industry is well-known to the world. Foundry industry is named as "The Father of Manufacturing Industry",and in Hong Kong there currently are 1 500 enterprises, staffed with 500 000 employees. The following are some special features of the Hong Kong foundry industry.

  17. A review and evaluation of the Langley Research Center's Scientific and Technical Information Program. Results of phase 4: Knowledge and attitudes survey, academic and industrial personnel

    Science.gov (United States)

    Pinelli, T. E.; Glassman, M.; Glassman, N. A.

    1981-01-01

    Feedback from engineers and scientists in the academic and industrial community provided an assessment of the usage and perceived quality of NASA Langley generated STI and the familiarity and usage of selected NASA publications and services and identified ways to increase the accessibility of Langley STI. The questionnaire utilized both open and closed ended questions and was pretested for finalization. The questions were organized around the seven objectives for Phase IV. From a contact list of nearly 1,200 active industrial and academic researchers, approximately 600 addresses were verified. The 497 persons who agreed to participate were mailed questionnaires. The 381 completed questionnaires received by the cutoff date were analyzed. Based on the survey findings, recommendations were made for increasing the familiarity with and use of NASA and Langley STI and selected NASA publications and services. In addition, recommendations were made for increasing the accessibility of Langley STI.

  18. External Strategic Analysis of the Aviation Maintenance, Repair and Overhaul (MRO) Industry and Potential Market Opportunities for Fleet Readiness Center Southwest

    Science.gov (United States)

    2009-06-01

    fashion . In 2004, the private partners accounted for only 2.2% of the $25.4 billion dollars of work performed; however, that figure is growing every year...resources on a more cost-effective basis” (Siemens PLM , 2008). Utilizing a total asset management approach assists firms in focusing their efforts on core...competencies required by the military aviation enterprise (Siemens PLM , 2008). 6) Competitive Position Transitioning to Industry – Implementation

  19. Centered on the Customer Experience Breakthrough Express Industry Competition%以客户体验为核心突破快递业竞争格局

    Institute of Scientific and Technical Information of China (English)

    赵永全; 于海燕

    2014-01-01

    伴随着经济的稳步发展和行业的全方位竞争,如何在更加有效地满足客户需求的基础上实现企业利润的突破,让服务的竞争核心回归服务本身,是快递业亟需解决的重要问题。文中主要围绕以客户体验为中心的差异化服务对快递业未来发展进行有益的探析。%Along with the steady development of economy and the comprehensive competition of the industry ,it has been an important problem for express industry that how to gain a breakthrough profits based on meeting the demand of customers more effectively and making the service competition core return to the service itself .This article mainly around the customer experience analyze the future of express industry .

  20. 延边呼叫中心产业存在的问题及其对策%Problems of the Call Center Service Industry in Yanbian and the Countermeasures

    Institute of Scientific and Technical Information of China (English)

    金龙哲; 金菊花

    2012-01-01

    呼叫中心产业是一个国家或地区经济发展的重要经济增长点,承接呼叫中心服务外包对现代服务业发展和产业结构调整具有重要的作用。延边呼叫中心产业还处于初级发展阶段,存在很多的问题,但延边与韩国、日本具有独特的地缘、人缘、语言优势,开展着频繁的经贸交流。韩国和日本较高的劳动力成本和竞争压力,是延边承接东北亚地区呼叫中心外包及其建设该产业基地的有利条件。为此,必须加强政府、学校、企业的密切结合,积极开展呼叫中心服务外包市场的开拓与促进活动,以加快延边呼叫中心产业建设的步伐。%As call center service industry is one of the most important economic growth engines for a country or region, to undertake the call center outsourcing service will be beneficial to the development of modern service industry and the adjustment of industrial structure. Though the industry in Yanbian is still on a primary stage and many problems need to be solved, frequent economic and trade contacts with Korea and Japan have been maintained due to the advantages in geography, people's communication and languages. The high cost of labor and keen competition in Korea and Japan are the favorable conditions for Yanbian to construct a base for the industry. Therefore, it is necessary to enhance the integration of governments, schools and enterprises so as to expand the outsourcing markets and quicken the construction of the industry in Yanbian.

  1. Industrial Inspection System

    Science.gov (United States)

    1993-01-01

    ACTIS+ is a smaller, personal computer version of ACTIS, a computed tomography system which finds its origins in the Apollo lunar landing research. It is used to identify imperfections in aerospace structures and components. Designed to be added to an existing real time radiography system, its components include a high precision rotation/elevation manipulator, color image monitor, graphical user interface monitor, and PC compatible workstation. Cross-sectional CT images are more detailed than radiographic images and the high speed scanning feature offers the capability for 100 percent inspection in a production environment. Bio-Imaging Research, Inc. (BIR) originally developed ACTIS for Marshall Space Flight Center (MSFC), and commercial units were sold to aerospace manufacturers. The technology was refined for ACTIS+, which is principally used in non-destructive testing.

  2. Digital radiography in the evaluation of oesophageal motility disorders

    Energy Technology Data Exchange (ETDEWEB)

    Aly, Yehia A

    2000-07-01

    AIMS: To develop a simple technique for examination of the oesophagus by digital radiography and to assess its role in the evaluation of motility disorders of the oesophagus. MATERIALS AND METHODS: Forty-nine patients and 44 control subjects underwent manometry and digital examination of the oesophagus. The digital study consisted of two parts: firstly examination of the pharynx and cervical oesophagus using 15 ml of fluid barium in anterio-posterior (AP) and lateral views, with image acquisition of four frames/s for 2 s. Secondly, examination of the thoracic oesophagus and oesophagogastric junction using 25 ml of barium in two prone oblique and one supine AP series, with image acquisition of one frame/s for 20 s. Oesophageal transit time (OTT) was measured in each case. Abnormal or non-peristaltic contractions were described regarding their morphology, time of visualization and length. The presence or absence of hiatal hernia, reflux or any associated organic lesions was noted. RESULTS: Digital radiography diagnosed 14 cases of achalasia and 28 cases of non-specific oesophageal motility disorder (NOMD). Normal OTT was 11.95 {+-} 1.304 s. The OTT was prolonged (16 s or more) in all patients except five; four of these were cases of NOMD. Abnormal contractions were classified into circular and longitudinal types. The circular non-obliterating type was commoner. Achalasia was diagnosed in all cases, as failure of relaxation of the inferior oesophageal sphincter was always present and easily depicted by digital radiography. Abnormal contractions in the body of the oesophagus were elicited in 57% of cases of achalasia. The sensitivity of digital radiography in detecting oesophageal motility disorders was 85.7% based on the presence of abnormal contractions and 91.6% by eliciting a prolonged OTT. CONCLUSIONS: Examination of the oesophagus by digital radiography is simple, non-invasive, reproducible, rapid and without discomfort to patients. It allows the diagnosis of

  3. Characterization of HANARO neutron radiography facility in accordance with ASTM standard E545-91/E803-91 for KOLAS/ISO17025.

    Science.gov (United States)

    Cheul-Muu, Sim; Ki-Yong, Nam; In-Cheol, Lim; Chang-Hee, Lee; Ha-Lim, Choi

    2004-10-01

    As neutron radiography is even more in demand for industrial applications of aircraft, turbine blade, automobile, explosive igniters, etc, it is necessary to review the standards which are the most appropriate for preparing the procedures for setting up the QA system. Recently, Korea Of Lab Accreditation Scheme (KOLAS) was originated from ISO 17025. It is widely recognized by research peer groups for conducting valid tests. The neutron radiography facility (NRF) of High Flux Advanced Neutron Application Reactor (HANARO), which started ion 1996, is the preliminary stages of KOLAS. The HANARO NRF is not only characterized using ASTM standards E545-91/E803-91 to satisfy the requirements of KOLAS, but in the design phase of the tomography system.

  4. Characterization of HANARO neutron radiography facility in accordance with ASTM standard E545-91/E803-91 for KOLAS/ISO17025

    Energy Technology Data Exchange (ETDEWEB)

    Cheul-Muu, Sim E-mail: cmsim@kaeri.re.kr; Ki-Yong, Nam; In-Cheol, Lim; Chang-Hee, Lee; Ha-Lim, Choi

    2004-10-01

    As neutron radiography is even more in demand for industrial applications of aircraft, turbine blade, automobile, explosive igniters, etc, it is necessary to review the standards which are the most appropriate for preparing the procedures for setting up the QA system. Recently, Korea Of Lab Accreditation Scheme (KOLAS) was originated from ISO 17025. It is widely recognized by research peer groups for conducting valid tests. The neutron radiography facility (NRF) of High Flux Advanced Neutron Application Reactor (HANARO), which started ion 1996, is the preliminary stages of KOLAS. The HANARO NRF is not only characterized using ASTM standards E545-91/E803-91 to satisfy the requirements of KOLAS, but in the design phase of the tomography system.

  5. Knowledge, Attitude and Performance of Shiraz General Dentists about Infection Control Principles during Preparing Intraoral Radiographies

    Directory of Open Access Journals (Sweden)

    Abdolaziz Hagh Negahdar

    2017-02-01

    Full Text Available Background & Objective: Infection control in dental centers is affected by the persons’ attitude and knowledge about mechanisms of infection transmission. This study was designed to evaluate the knowledge and the attitude of Shiraz dentists about infection control during intraoral radiographies preparation. Materials & Methods: In this cross-sectional, and analytical research, the attitude and the knowledge of 45 male and 25 female, randomly selected dentists, were obtained through completion of a researcher- planed questioner which its validity and reliability had been confirmed. Data were analyzed using Cronbach`s alpha, one-way ANOVA, student’s t-test, and Pearson’s correlation coefficient in SPSS (V.21. Results: The average of the dentists’ age was 40.59±10.72 and their average occupational experience was 13.49±9.75 years. The mean score obtained for knowledge about infection control during intraoral radiographic procedures was less than fifty percent of total obtainable score, and was assessed as weak knowledge. There was no significant difference in the level of knowledge between studied male and female dentists (P>0.05. In addition, no significant relationship was detected between level, age/experience, and the university of education (P>0.05. The attitude of the dentists about infection control during intraoral radiography preparation assessed as moderate to good level. Conclusions: The results showed that the main reason for the present problems is insufficient knowledge of the dentists in related subjects. Therefore, the solution, which is recommended among dentists, is to raise their awareness and to change their attitudes and culture in order to improve their performance.

  6. Documented Safety Analysis Addendum for the Neutron Radiography Reactor Facility Core Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Boyd D. Christensen

    2009-05-01

    The Neutron Radiography Reactor Facility (NRAD) is a Training, Research, Isotope Production, General Atomics (TRIGA) reactor which was installed in the Idaho National Laboratory (INL) Hot Fuels Examination Facility (HFEF) at the Materials and Fuels Complex (MFC) in the mid 1970s. The facility provides researchers the capability to examine both irradiated and non-irradiated materials in support of reactor fuel and components programs through non-destructive neutron radiography examination. The facility has been used in the past as one facet of a suite of reactor fuels and component examination facilities available to researchers at the INL and throughout the DOE complex. The facility has also served various commercial research activities in addition to the DOE research and development support. The reactor was initially constructed using Fuel Lifetime Improvement Program (FLIP)- type highly enriched uranium (HEU) fuel obtained from the dismantled Puerto Rico Nuclear Center (PRNC) reactor. In accordance with international non-proliferation agreements, the NRAD core will be converted to a low enriched uranium (LEU) fuel and will continue to utilize the PRNC control rods, control rod drives, startup source, and instrument console as was previously used with the HEU core. The existing NRAD Safety Analysis Report (SAR) was created and maintained in the preferred format of the day, combining sections of both DOE-STD-3009 and Nuclear Regulatory Commission Regulatory Guide 1.70. An addendum was developed to cover the refueling and reactor operation with the LEU core. This addendum follows the existing SAR format combining required formats from both the DOE and NRC. This paper discusses the project to successfully write a compliant and approved addendum to the existing safety basis documents.

  7. Reliability of quality measures of movement in lumbar spine flexion-extension radiography.

    Science.gov (United States)

    Taghipour-Darzi, Mohammad; Ebrahimi-Takamjani, Esmail; Salavati, Mahyar; Mobini, Bahram; Zekavat, Hajar

    2009-01-01

    For center of rotation (COR) and centroid length variables in lumbar flexion-extension radiography, enough reliability information is not available. The objective of this study was to determine the intra-rater reliability of COR and centroid length of lumbar intervertebral movement. A methodological research for reliability was designed. Fifteen males with chronic non specific low back pain aged between 22-43 years participated in this study. Study variables included COR of full, flexion and extension arc and centroid length. The proposed method from Putto was used for flexion-extension radiography. Five x-rays were taken in neutral, full flexion and extension, mid-flexion and mid-extension positions. The variables were calculated using Computer Aided Radiographic Analysis of Spine (CARA) software after scanning. The intraclass correlation coefficient (ICC) and standard error of measurement (SEM) were utilized for relative and absolute reliability respectively. The results demonstrated high ICC values on x axis (range: 0.67-0.88) and y axis (range: 0.55-0.90) for full arc COR, high ICC values of flexion arc COR on x axis (range: 0.54-0.97) and y axis (range: 0.48-0.99). ICC values results of extension arc ranged between 0.19-0.60 for x axis and 0.16-0.83 for y axis. ICC values for centroid length ranged between 0.22-0.88. Results support previous studies which show very high reliability of full arc COR. In addition, flexion arc COR has desirable reliability and low measurement errors. But, extension arc COR and centroid length have moderate reliability and large measurement errors.

  8. Initial results from a multiple monoenergetic gamma radiography system for nuclear security

    Science.gov (United States)

    O'Day, Buckley E.; Hartwig, Zachary S.; Lanza, Richard C.; Danagoulian, Areg

    2016-10-01

    The detection of assembled nuclear devices and concealed special nuclear materials (SNM) such as plutonium or uranium in commercial cargo traffic is a major challenge in mitigating the threat of nuclear terrorism. Currently available radiographic and active interrogation systems use ∼1-10 MeV bremsstrahlung photon beams. Although simple to build and operate, bremsstrahlung-based systems deliver high radiation doses to the cargo and to potential stowaways. To eliminate problematic issues of high dose, we are developing a novel technique known as multiple monoenergetic gamma radiography (MMGR). MMGR uses ion-induced nuclear reactions to produce two monoenergetic gammas for dual-energy radiography. This allows us to image the areal density and effective atomic number (Zeff) of scanned cargo. We present initial results from the proof-of-concept experiment, which was conducted at the MIT Bates Research and Engineering Center. The purpose of the experiment was to assess the capabilities of MMGR to measure areal density and Zeff of container cargo mockups. The experiment used a 3.0 MeV radiofrequency quadrupole accelerator to create sources of 4.44 MeV and 15.11 MeV gammas from the 11B(d,nγ)12C reaction in a thick natural boron target; the gammas are detected by an array of NaI(Tl) detectors after transmission through cargo mockups . The measured fluxes of transmitted 4.44 MeV and 15.11 MeV gammas were used to assess the areal density and Zeff. Initial results show that MMGR is capable of discriminating the presence of high-Z materials concealed in up to 30 cm of iron shielding from low- and mid-Z materials present in the cargo mockup.

  9. Evaluation of diagnostic ability of CCD digital radiography in the detection of incipient dental caries

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Wan; Lee, Byung Do [Wonkwang University College of Medicine, Iksan (Korea, Republic of)

    2003-03-15

    The purpose of this experiment was to evaluate the diagnostic ability of a CCD-based digital system (CDX-2000HQ) in the detection of incipient dental caries. 93 extracted human teeth with sound proximal surfaces and interproximal artificial cavities were radiographed using 4 imaging methods. Automatically processed No.2 Insight film (Eastman Kodak Co., U.S.A.) was used for conventional radiography, scanned images of conventional radiograms for indirect digital radiography were used. For the direct digital radiography, the CDX-2000HQ CCD system (Biomedisys Co. Korea) was used. The subtraction images were made from two direct digital images by Sunny program in the CDX-2000HQ system. Two radiologists and three endodontists examined the presence of lesions using a five-point confidence scale and compared the diagnostic ability by ROC (Receiver Operating Characteristic) analysis and one way ANOVA test. The mean ROC areas of conventional radiography, indirect digital radiography, direct digital radiography, and digital subtraction radiography were 0.9093, 0.9102, 0.9184, and 0.9056, respectively. The diagnostic ability of direct digital radiography was better than the other imaging modalities, but there were no statistical differences among these imaging modalities (p>0.05). These results indicate that new CCD-based digital systems (CDX-2000HQ) have the potential to serve as an alternative to conventional radiography in the detection of incipient dental caries.

  10. Diagnostic value of pelvic radiography in the initial trauma series in blunt trauma

    Energy Technology Data Exchange (ETDEWEB)

    Their, Micael E.A.; Bensch, Frank V.; Koskinen, Seppo K. [Toeoeloe Trauma Center, Department of Radiology, Helsinki University Central Hospital, Helsinki (Finland); Handolin, Lauri [Toeoeloe Trauma Center, Department of Orthopaedics and Traumatology, Helsinki (Finland); Kiuru, Martti J. [Toeoeloe Trauma Center, Department of Radiology, Helsinki University Central Hospital, Helsinki (Finland); Research Institut of Military Medicine, Helsinki (Finland)

    2005-08-01

    The purpose of the study was to evaluate the diagnostic value of pelvic radiography in the initial trauma series when compared to multidetector CT (MDCT) findings in serious blunt trauma. Inclusion criteria were blunt trauma and pelvic radiography in the initial trauma series, followed by a whole-body MDCT. A total of 1386 patients (874 male, 512 female, age 16-91 years, mean 41 years) met the inclusion criteria. Imaging studies were evaluated retrospectively by anatomical region and classified, when possible, using the Tile classification. Based on MDCT, a total of 629 injuries occurred in 226 (16%) of these 1386 patients. Radiography depicted 405 fractures in these 226 patients, giving an overall sensitivity of 55%. In 24 patients (11%) radiography was false-negatively normal. The sensitivity of radiography was mainly good in the anteroinferior parts of the pelvis, fair in the acetabulum and ileum, and poor in the posterior ring. By MDCT 141 (62%) patients were classified using the Tile classification and by radiography 133 patients (59%) were classified. MDCT and radiography showed the same type of pelvic injury in 72 patients (59%) and the subtype in 17 patients (14%). In 48 patients (40%) the pelvis was shown to be stable by radiography but unstable by MDCT. In conclusion, the sensitivity of pelvic radiography is low, and it is not reliable for determining if the pelvic injury is stable or not. (orig.)

  11. Value of postmortem thoracic CT over radiography in imaging of pediatric rib fractures

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Terence S.; Babyn, Paul S. [The Hospital for Sick Children, Department of Diagnostic Imaging, Toronto (Canada); Reyes, Jeanette A.; Chiasson, David A. [The Hospital for Sick Children, Department of Paediatric Laboratory Medicine, Toronto (Canada); Moineddin, Rahim [University of Toronto, Department of Family and Community Medicine, Toronto (Canada); Berdon, Walter E. [Columbia Presbyterian Medical Center, Babies Hospital, Department of Radiology, New York, NY (United States)

    2011-06-15

    Studies have reported that thoracic CT may provide greater sensitivity compared with radiography in detection of pediatric rib fractures and fracture healing. The additional sensitivity afforded by thoracic CT may have medicolegal implications where abuse is suspected. To determine the additional value of postmortem thoracic CT compared with radiography in detecting pediatric rib fractures, and fracture healing, using autopsy findings as a gold standard. We retrospectively reviewed 56 coroner's cases with postmortem radiography and CT thoracic survey. All studies underwent primary interpretation by one or two radiologists. The study radiologist independently reviewed all images from 13 patients with positive findings on radiography, CT or autopsy. Sensitivity and specificity between observers and imaging modalities were compared. Primary interpretation: Fractures were recognized on radiography in 5/12 patients who had fractures found at autopsy, and on CT in 8/12 patients. In total, 29% (24/83) of fractures were reported on radiography, and 51% (52/101) of fractures were reported on CT. Study radiologist: Fractures were recognized on radiography in 7/12 patients who had fractures found at autopsy, and on CT in 11/12 patients. In total, 46% (38/83) of fractures were reported on radiography, and 85% (86/101) of fractures were reported on CT. Postmortem thoracic CT provides greater sensitivity than radiography in detecting pediatric rib fractures, most notably in anterior and posterior fractures. However, the degree of improvement in sensitivity provided by CT might depend on observer experience. (orig.)

  12. Trabalho e movimento sindical nos novos pólos automotivos no Brasil Work and union movement in the new brazilian car industry centers

    Directory of Open Access Journals (Sweden)

    Rosana Ribeiro

    2007-09-01

    Full Text Available A indústria automotiva cresceu nos anos 90, quando as montadoras criaram unidades fora da Grande São Paulo em busca de trabalhadores sem tradição na negociação sindical, dentre outros motivos. Destaca-se aqui a criação da Mitsubishi em Catalão (GO e da Volkswagen em Resende (RJ. A organização do trabalho, o perfi socioeconômico dos trabalhadores e o movimento sindical nessas plantas são analisados neste artigo. Embora na MMC o processo de trabalho seja tido como arcaico, a organização da produção de ambas é híbrida. A maioria dos trabalhadores é da própria cidade e inclui jovens com escolaridade alta, mas sem a cultura industrial do setor automotivo e a tradição sindical. A falta de tradição sindical, porém, começa a se erodir: em Resende, o sindicato se mostra comprometido com seus representados: participa de acordo coletivo e mantém comissão de fábrica; em Catalão, ao final de 2004, foi criado um sindicato dos trabalhadores metalúrgicos, que também iniciou uma trajetória de luta pelos interesses de sua base. Palavras-chave: Indústria automotiva. Trabalhadores. Sindicatos. Catalão. Resende. Motor industry in Brazil has increased in the 90s, when companies set up plants outside of São Paulo in search for workers with no experience in trade union negotiations, among others motives. In this article we focus on the cases of Mitsubishi in Catalão (state of Goiás and Volkswagen in Resende (Rio de Janeiro, by analyzing the organization of work, workers’ socioeconomic profiles and union movement in these plants. Although working conditions at MMC are seen as outmoded, both plants maintain a hybrid organization. A good deal of workers comes from Catalão and includes young highly educated males lacking, however, the industrial culture peculiar to the automotive sector as well as tradition in union trading. The lack of labor union tradition, however, starts to erode. In Resende the union seems to be committed

  13. Role function and job satisfaction: a study of nurse graduates of educational resource center programs employed by the health care industry.

    Science.gov (United States)

    Guzik, V L; McGovern, P M; Kochevar, L K

    1992-11-01

    This study analyzed the roles, functions, and job satisfaction of 65 master's prepared occupational health nurses employed within the health care industry to compare nurses who function as internal consultants with those who function as external consultants. The only significant difference between groups was that external consultants were more involved in marketing and management functions, whereas internal consultants were more involved in direct care. The study hypothesis that occupational health nurses performing more management functions would report greater job satisfaction was not supported by the data. Study findings did support a theoretical model by Hardy, revealing that greater role certainty and more role adapting behaviors were significantly associated with job satisfaction.

  14. Cultural Industries Bloom

    Institute of Scientific and Technical Information of China (English)

    ZAN JIFANG

    2010-01-01

    @@ The market scale of China's cultural industries reached around 800 billion yuan($118 billion)in 2009,said a report on China's cultural industry development jointly released by a cultural research center under the Chinese Academy of Social Sciences and the academy's Social Sciences Academic Press on May 6.

  15. Skeletal imaging following reconstruction of the posterior cruciate ligament: in vivo comparison of fluoroscopy, radiography, and computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Osti, Michael; Benedetto, Karl Peter [Academic Hospital Feldkirch, Department for Trauma Surgery and Sports Traumatology, Feldkirch (Austria); Krawinkel, Alessa [Academic Hospital Feldkirch, Department for Radiology, Feldkirch (Austria)

    2014-12-15

    Intra- and postoperative validation of anatomic footprint replication in posterior cruciate ligament (PCL) reconstruction can be conducted using fluoroscopy, radiography, or computed tomography (CT) scans. However, effectiveness and exposure to radiation of these imaging modalities are unknown. The objective of this study was to evaluate the comparative effectiveness of fluoroscopy, radiography, and CT in detecting femoral and tibial tunnel positions following an all-inside reconstruction of the PCL ligament in vivo. The study design was a retrospective case series. Intraoperative fluoroscopic images, postoperative radiographs, and CT scans were obtained in 50 consecutive patients following single-bundle PCL reconstruction. The centers of the tibial and femoral tunnel apertures were identified and correlated to measurement grid systems. The results of fluoroscopic, radiographic, and CT measurements were compared to each other and accumulated radiation dosages were calculated. Comparing the imaging groups, no statistically significant difference could be detected for the reference of the femoral tunnel to the intercondylar depth and height, for the reference of the tibial tunnel to the mediolateral diameter of the tibial plateau and for the superoinferior distance of the tibial tunnel entry to the tibial plateau and to the former physis line. Effective doses resulting from fluoroscopic, radiographic, and CT exposure averaged 2.9 mSv, standard deviation (±SD) 4.1 mSv, to 1.3 ± 0.8 mSv and to 3.6 ± 1.0 mSv, respectively. Fluoroscopy, radiography, and CT yield approximately equal effectiveness in detecting parameters used for quality validation intra- and postoperatively. An accumulating exposure to radiation must be considered. (orig.)

  16. Evaluation of the Quality Control Program for Diagnostic Radiography and Fluoroscopy Devices in Syria during 2005-2013

    Directory of Open Access Journals (Sweden)

    M. H. Kharita

    2017-06-01

    Full Text Available Introduction: Extensive use of diagnostic radiology is the largest contributor to total population radiation doses. Thus, appropriate equipment and safe practice are necessary for good-quality images with optimal doses. This study aimed to perform quality control (QC audit for radiography and fluoroscopy devices owned by private sector in Syria (2005-2013 to verify compliance of performance of X-ray machines with the regulatory requirements stipulated by the national regulatory body. Materials and Methods: In this study, QC audit included 487 X-ray diagnostic machines, (363 radiography and 124 fluoroscopy devices, installed in 306 medical diagnostic radiology centers in 14 provinces in Syria. We employed an X-ray beam analyzer device (NERO model 8000, Victoreen, USA, which was tested and calibrated at the National Secondary Standard Dosimetry Laboratory traceable to the IAEA Network of Secondary Standard Dosimetry Laboratories. Standard QC tool kits were used to evaluate tube and generator of the X-ray machines, which constituted potential (kVp, timer accuracy, radiation output consistency, tube filtration, small and large focal spot sizes, X-ray beam collimation and alignment, as well as high- and low-resolution and entrance surface dose in fluoroscopy. Results: According to our results, most of the assessed operating parameters were in compliance with the standards stipulated by the National Regulatory Authority. In cases of noncompliance for the assessed parameters, maximum value (28.77% pertained to accuracy of kVp calibration for radiography units, while the lowest value (2.42% belonged to entrance surface dose in fluoroscopy systems. Conclusion: Effective QC program in diagnostic radiology leads to obtaining information regarding quality of radiology devices used for medical diagnosis and minimizing the doses received by patients and medical personnel. The findings of this QC program, as the main part of QA program, illustrated that most

  17. Single-image hard-copy display of the spine utilizing digital radiography

    Science.gov (United States)

    Artz, Dorothy S.; Janchar, Timothy; Milzman, David; Freedman, Matthew T.; Mun, Seong K.

    1997-04-01

    and lateral thoracic spine that typically have a low optical density value, the DRC algorithm used increased the optical density over that region improving visualization of C7-T2 and T11-L2 vertebral bodies; critical in trauma radiography. Emergency medicine physicians also reviewing the lateral cervical spine images were able to clear 37% of the DRC images compared to 30% of the non-DRC images for removal of the cervical collar. The DRC processed images reviewed by the physicians do not have a typical screen/film appearance; however, these different images were preferred for the three examinations in this study. This method of image processing after being tested and accepted, is in use clinically at Georgetown University Medical Center Department of Radiology for the following examinations: cervical spine, lateral thoracic spine, lateral thoracolumbar examinations, facial bones, shoulder, sternum, feet and portable chest. Computed radiography imaging of the spine is improved with the addition of histogram equalization known as dynamic range control (DRC). More anatomical structures are visualized on a single hard copy display.

  18. Acute paediatric ankle trauma: MRI versus plain radiography

    Energy Technology Data Exchange (ETDEWEB)

    Lohman, M. [Helsinki Univ. Central Hospital (Finland). Dept. of Radiology; Radiological Dept., Helsinki University Central Hospital (Finland); Kivisaari, A.; Kivisaari, L. [Helsinki Univ. Central Hospital (Finland). Dept. of Radiology; Kallio, P.; Puntila, J. [Dept. of Paediatric Surgery, Hospital for Children and Adolescents, Helsinki Univ. Central Hospital, Helsinki (Finland); Vehmas, T. [Finnish Institute of Occupational Health, Helsinki (Finland)

    2001-09-01

    Objective: To evaluate the diagnosis of acute physeal ankle fractures on plain radiographs using MRI as the gold standard. Methods: Sixty consecutive children, 29 with a clinical diagnosis of lateral ligament injury and 31 with physeal ankle fractures, were examined using both radiographs and MRI in the acute period. The imaging data were reviewed by three ''masked'' radiologists. The fracture diagnosis and Slater-Harris classification of radiographs were compared with findings on MRI. Results: Plain radiography produced five of 28 (18%) false negative and 12 of 92 (13%) false positive fracture diagnoses compared with MRI. Six of the 12 false positive fractures were due to a misclassification of lateral ligament disruption as SH1 fractures. Altogether a difference was found in 21% of cases in either the diagnosis or the classification of the fractures according to Salter- Harris. All bone bruises in the distal tibia and fibula and 64% of bone bruises in the talus were seen in association with lateral ligament injuries. Talar bone bruises in association with fractures occurred on the same side as the malleolar fracture; talar bone bruises in association with lateral ligament disruption were seen in different locations. The errors identified on radiographs by MRI did not affect the management of the injury. Conclusions: The incidence of false negative ankle fractures in plain radiographs was small and no complex ankle fractures were missed on radiographs. The total extent of complex fractures was, however, not always obvious on radiographs. In an unselected series of relatively mild ankle injuries, we were unable to show a single case where the treatment or prognosis based on plain radiography should have been significantly altered after having done a routine MRI examination. Plain radiography is still the diagnostic cornerstone of paediatric ankle injuries. (orig.)

  19. Spectroscopic neutron radiography for a cargo scanning system

    Energy Technology Data Exchange (ETDEWEB)

    Rahon, Jill [Department of Nuclear Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Ave, Cambridge, MA 02139 (United States); Danagoulian, Areg, E-mail: aregjan@mit.edu [Department of Nuclear Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Ave, Cambridge, MA 02139 (United States); MacDonald, Thomas D. [Department of Nuclear Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Ave, Cambridge, MA 02139 (United States); Hartwig, Zachary S. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, 77 Massachusetts Ave, Cambridge, MA 02139 (United States); Lanza, Richard C. [Department of Nuclear Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Ave, Cambridge, MA 02139 (United States)

    2016-06-01

    Detection of cross-border smuggling of illicit materials and contraband is a challenge that requires rapid, low-dose, and efficient radiographic technology. The work we describe here is derived from a technique which uses monoenergetic gamma rays from low energy nuclear reactions, such as {sup 11}B(d,nγ){sup 12}C, to perform radiographic analysis of shipping containers. Transmission ratios of multiple monoenergetic gamma lines resulting from several gamma producing nuclear reactions can be employed to detect materials of high atomic number (Z), the details of which will be described in a separate paper. Inherent in this particular nuclear reaction is the production of fast neutrons which could enable neutron radiography and further characterization of the effective-Z of the cargo, especially within the range of lower Z. Previous research efforts focused on the use of total neutron counts in combination with X-ray radiography to characterize the hydrogenous content of the cargo. We present a technique of performing transmitted neutron spectral analysis to reconstruct the effective Z and potentially the density of the cargo. This is made possible by the large differences in the energy dependence of neutron scattering cross-sections between hydrogenous materials and those of higher Z. These dependencies result in harder transmission spectra for hydrogenous cargoes than those of non-hydrogenous cargoes. Such observed differences can then be used to classify the cargo based on its hydrogenous content. The studies presented in this paper demonstrate that such techniques are feasible and can provide a contribution to cargo security, especially when used in concert with gamma radiography.

  20. Spectroscopic neutron radiography for a cargo scanning system

    Science.gov (United States)

    Rahon, Jill; Danagoulian, Areg; MacDonald, Thomas D.; Hartwig, Zachary S.; Lanza, Richard C.

    2016-06-01

    Detection of cross-border smuggling of illicit materials and contraband is a challenge that requires rapid, low-dose, and efficient radiographic technology. The work we describe here is derived from a technique which uses monoenergetic gamma rays from low energy nuclear reactions, such as 11B(d,nγ)12C, to perform radiographic analysis of shipping containers. Transmission ratios of multiple monoenergetic gamma lines resulting from several gamma producing nuclear reactions can be employed to detect materials of high atomic number (Z), the details of which will be described in a separate paper. Inherent in this particular nuclear reaction is the production of fast neutrons which could enable neutron radiography and further characterization of the effective-Z of the cargo, especially within the range of lower Z. Previous research efforts focused on the use of total neutron counts in combination with X-ray radiography to characterize the hydrogenous content of the cargo. We present a technique of performing transmitted neutron spectral analysis to reconstruct the effective Z and potentially the density of the cargo. This is made possible by the large differences in the energy dependence of neutron scattering cross-sections between hydrogenous materials and those of higher Z. These dependencies result in harder transmission spectra for hydrogenous cargoes than those of non-hydrogenous cargoes. Such observed differences can then be used to classify the cargo based on its hydrogenous content. The studies presented in this paper demonstrate that such techniques are feasible and can provide a contribution to cargo security, especially when used in concert with gamma radiography.

  1. Characterization of non-tuberculosis mycobacteria by neutron radiography.

    Science.gov (United States)

    da Silva, Jaqueline M; Crispim, Verginia Reis; da Silva, Marlei Gomes; Furtado, Vanessa Rodrigues; Duarte, Rafael Da Silva

    2013-07-01

    The genus Mycobacterium shares many characteristics with Corynebacterium and Actinomyces genera, among which the genomic guanine plus cytosine content and the production of long branched-chain fatty acids, known as mycolic acids are enhanced. Growth rate and optimal temperature of mycobacteria are variable. The genus comprises more than 140 known species; however Mycobacterium fortuitum, a fast growing nontuberculous mycobacterium, is clinically significant, because it has been associated to several lesions following surgery procedures such as liposuction, silicone breast and pacemaker implants, exposure to prosthetic materials besides sporadic lesions in the skin, soft tissues and rarely lungs. The objective of the present study is to reduce the time necessary for M. fortuitum characterization based on its morphology and the use of the neutron radiography technique substituting the classical biochemical assays. We also aim to confirm the utility of dendrimers as boron carriers. The samples were sterilized through conventional protocols using 10% formaldehyde. In the incubation process, two solutions with different molar ratios (10:1 and 20:1) of sodium borate and PAMAM G4 dendrimer and also pure sodium borate were used. After doping and sterilization procedures, the samples were deposited on CR-39 sheets, irradiated with a 4.6×10(5) n/cm(2)s thermal neutron flux for 30 min, from the J-9 irradiation channel of the Argonauta IEN/CNEN reactor. The images registered in the CR-39 were visualized in a Nikon E400 optical transmission microscope and captured by a Nikon Coolpix 995 digital camera. Developing the nuclear tracks registered in the CR-39 allowed a 1000× enlargement of mycobacterium images, facilitating their characterization, the use of more sophisticated equipment not being necessary. The use of neutron radiography technique reduced the time necessary for characterization. Doping with PAMAM dendrimer improved the visualization of NTM in neutron radiography

  2. Polychlorinated biphenyls in settled dust from informal electronic waste recycling workshops and nearby highways in urban centers and suburban industrial roadsides of Chennai city, India: Levels, congener profiles and exposure assessment.

    Science.gov (United States)

    Chakraborty, Paromita; Prithiviraj, Balasubramanian; Selvaraj, Sakthivel; Kumar, Bhupander

    2016-12-15

    Polychlorinated biphenyls (PCBs) were quantified in settled dust collected from informal electronic waste (e-waste) recycling workshops and nearby highways in the urban centers and roadside dust from the suburban industrial belt of Chennai city in India. Further dust samples were subjected to a high resolution field emission scanning electron microscope equipped with an energy dispersive X-ray spectrometer (FESEM/EDX) to characterize the shape, size and elemental composition of the dust particles. Geomean of total PCB concentration followed the following order: informal e-waste metal recovery workshops (53ngg(-1))>e-waste dismantling sites (3.6ngg(-1))>nearby highways (1.7ngg(-1))>suburban industrial roadsides (1.6ngg(-1)). In e-waste workshops, tetra, penta and hexa-PCB homologs contributed two third of Σ26PCB concentration. Informal e-waste recycling workshops contributed more than 80% concentration of all the PCB congeners loaded in the first principal component. Predominance of dioxin like PCBs, PCB-l14, -118 and -126 in the e-waste metal recovery sites were presumably due to combustion and pyrolytic processes performed during recycling of electrical components. According to the morphology and elemental composition, settled dust from e-waste workshops were irregular particles heavily embedded with toxic metals and industrial roadside dust were distinct angular particles. FESEM revealed that average particle size (in Ferret diameter) increased in the following order: e-waste recycling workshops (0.5μm)industrial sites (4.3μm). Electronic waste recycling workshops engaged in metal recovery were found with maximum toxicity equivalents (TEQs) for dl-PCBs and potential cancer risk (10(-6)-10(-4)) for both adult and children.

  3. A novel type epithermal neutron radiography detecting and imaging system

    CERN Document Server

    Balasko, M; Svab, E; Eoerdoegh, I

    1999-01-01

    The transfer technique is widely used for epithermal neutron radiography (ENR) for making images upon the object to be investigated. We propose to use instead of the photosensitive film a gamma sensitive scintillation screen (NaCe single crystal), that is monitored by a computer controlled low light level TV camera. The exposure time has been reduced to a duration of only a short fraction of that needed for the conventional transfer process. The presented ENR images consist of electronic signals that are handled by an advanced image processing and analyzing program, the Iman 1.4 version, using a task oriented video grabber.

  4. Fail-safe neutron shutter used for thermal neutron radiography

    Energy Technology Data Exchange (ETDEWEB)

    Sachs, R.D.; Morris, R.A.

    1976-11-01

    A fail-safe, reliable, easy-to-use neutron shutter was designed, built, and put into operation at the Omega West Reactor, Los Alamos Scientific Laboratory. The neutron shutter will be used primarily to perform thermal neutron radiography, but is also available for a highly collimated source of thermal neutrons (neutron flux = 3.876 x 10/sup 6/ (neutrons)/(cm/sup 2/.s)). Neutron collimator sizes of either 10.16 by 10.16 cm or 10.16 by 30.48 cm are available.

  5. Upgrading of neutron radiography/tomography facility at research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Abd El Bar, Waleed; Mongy, Tarek [Atomic Energy Authority, Cairo (Egypt). ETRR-2; Kardjilov, Nikolay [Helmholtz Zentrum Berlin (HZB) for Materials and Energy, Berlin (Germany)

    2014-03-15

    A state-of-the-art neutron tomography imaging system was set up at the neutron radiography beam tube at the Egypt Second Research Reactor (ETRR-2) and was successfully commissioned in 2013. This study presents a set of tomographic experiments that demonstrate a high quality tomographic image formation. A computer technique for data processing and 3D image reconstruction was used to see inside a copy module of an ancient clay article provided by the International Atomic Energy Agency (IAEA). The technique was also able to uncover tomographic imaging details of a mummified fish and provided a high resolution tomographic image of a defective fire valve. (orig.)

  6. Detectability of simulated vessels by computed radiography and digital fluorography

    Energy Technology Data Exchange (ETDEWEB)

    Misumi, Wataru; Yoshioka, Senya; Korogi, Yukunori; Takahashi, Mutsumasa (Kumamoto Univ. (Japan). School of Medicine); Higashida, Yoshiharu

    1990-05-01

    Phantom studies were carried out to determine the ability to digital subtraction angiography (DSA), using either Fuji computed radiography (CR) or digital fluorography (DF) system, to detect the simulated vessels. The assessment of detectability was based on observer performance techniques. DFDSA was superior to CRDSA. Detectability of CRDSA was influenced by the incident X-ray exposures. Even though it was improved by contrast enhancement, the magnitude of improvement was dependent upon the incident X-ray exposures and vessel size. (N.K.).

  7. Panoramic radiography for temporomandibular joint arthrography: a description of arthropanoramograms.

    Science.gov (United States)

    Abramovitch, K; Langlais, R P; Dolwick, M F

    1989-06-01

    TMJ arthrograms done with panoramic radiography, i.e., arthropanoramography, can demonstrate intracapsular disk displacement and perforation pathoses. These views are very practical for inferior synovial cavity arthrograms performed in the dental operatory since panoramic radiographic machines have become common in modern dental practices. Specific advantages of arthropanoramography include the decreased financial cost and decreased radiation exposure to the patient. Arthropanoramography does not replace tomography or videofluoroscopy in TMJ arthrography. It is, however, described as a simple alternative to the more conventional forms of arthrography.

  8. High efficiency gaseous tracking detector for cosmic muon radiography

    CERN Document Server

    Varga, Dezső; Hamar, Gergő; Oláh, László

    2016-01-01

    A tracking detector system has been constructed with an innovative approach to the classical multi-wire proportional chamber concept, using contemporary technologies. The detectors, covering an area of 0.58 square meters each, are optimized for the application of muon radiography. The main features are high (>99.5%) and uniform detection efficiency, 9 mm FWHM position resolution, filling gas consumption below 2 liters per hour for the non toxic, non flammable argon and carbon dioxide mixture. These parameters, along with the simplicity of the construction and the tolerance for mechanical effects, make the detectors to be a viable option for a large area muography observation system.

  9. Computed radiography simulation using the Monte Carlo code MCNPX

    Energy Technology Data Exchange (ETDEWEB)

    Correa, S.C.A. [Programa de Engenharia Nuclear/COPPE, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970, Rio de Janeiro, RJ (Brazil); Centro Universitario Estadual da Zona Oeste (CCMAT)/UEZO, Av. Manuel Caldeira de Alvarenga, 1203, Campo Grande, 23070-200, Rio de Janeiro, RJ (Brazil); Souza, E.M. [Programa de Engenharia Nuclear/COPPE, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970, Rio de Janeiro, RJ (Brazil); Silva, A.X., E-mail: ademir@con.ufrj.b [PEN/COPPE-DNC/Poli CT, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970, Rio de Janeiro, RJ (Brazil); Cassiano, D.H. [Instituto de Radioprotecao e Dosimetria/CNEN Av. Salvador Allende, s/n, Recreio, 22780-160, Rio de Janeiro, RJ (Brazil); Lopes, R.T. [Programa de Engenharia Nuclear/COPPE, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970, Rio de Janeiro, RJ (Brazil)

    2010-09-15

    Simulating X-ray images has been of great interest in recent years as it makes possible an analysis of how X-ray images are affected owing to relevant operating parameters. In this paper, a procedure for simulating computed radiographic images using the Monte Carlo code MCNPX is proposed. The sensitivity curve of the BaFBr image plate detector as well as the characteristic noise of a 16-bit computed radiography system were considered during the methodology's development. The results obtained confirm that the proposed procedure for simulating computed radiographic images is satisfactory, as it allows obtaining results comparable with experimental data.

  10. BBU design of linear induction accelerator cells for radiography application

    Energy Technology Data Exchange (ETDEWEB)

    Shang, C.C.; Chen, Y.J.; Gaporaso, G.J.; Houck, T.L.; Molau, N.E.; Focklen, J.; Gregory, S.

    1997-05-06

    There is an ongoing effort to develop accelerating modules for high-current electron accelerators for advanced radiography application. Accelerating modules with low beam-cavity coupling impedances along with gap designs with acceptable field stresses comprise a set of fundamental design criteria. We examine improved cell designs which have been developed for accelerator application in several radiographic operating regimes. We evaluate interaction impedances, analyze the effects of beam structure coupling on beam dynamics (beam break-up instability and corkscrew motion). We also provide estimates of coupling through interesting new high-gradient insulators and evaluate their potential future application in induction cells.

  11. Assessment of risk of potential exposures on facilities industries; Estimativa do risco de exposicao potencial em instalacoes industriais

    Energy Technology Data Exchange (ETDEWEB)

    Leocadio, Joao Carlos

    2007-03-15

    This work develops a model to evaluate potential exposures on open facilities of industrial radiography in Brazil. This model will decisively contribute to optimize operational, radiological protection and safety procedures, to prevent radiation accidents and to reduce human errors in industrial radiography. The probabilistic safety assessment (PSA) methodology was very useful to assess potential exposures. The open facilities of industrial radiography were identified as the scenario to be analyzed in what concerns the evaluation of potential exposures, due to their high accidents indices. The results of the assessment of potential exposures confirm that the industrial radiography in Brazil is a high-risk practice as classified by the IAEA. The risk of potential exposure was estimated to be 40,5 x 10{sup -2} per year in Brazil, having as main consequences injuries to the workers' hands and arms. In the world scene, the consequences are worst, leading to fatalities of people, thus emphasizing the high risk of industrial radiography. (author)

  12. Quantitative studies on inner interfaces in conical metal joints using hard x-ray inline phase contrast radiography

    Energy Technology Data Exchange (ETDEWEB)

    Zabler, S. [Institute for Materials Science, Technical University of Berlin, EB 13, Strasse des 17, Juni 135, D-10623 Berlin (Germany); Rack, T.; Nelson, K. [Clinic for Oral and Maxifacial Surgery, Charite University Medicine, Augustenburger Platz 1, D-13353 Berlin (Germany); Rack, A. [European Synchrotron Radiation Facility, 6 rue Jules Horowitz, BP 220, F-38043 Grenoble (France)

    2010-10-15

    Quantitative investigation of micrometer and submicrometer gaps between joining metal surfaces is applied to conical plug-socket connections in dental titanium implants. Microgaps of widths well beyond the resolving power of industrial x-ray systems are imaged by synchrotron phase contrast radiography. Furthermore, by using an analytical model for the relatively simple sample geometry and applying it to numerical forward simulations of the optical Fresnel propagation, we show that quantitative measurements of the microgap width down to 0.1 {mu}m are possible. Image data recorded at the BAMline (BESSY-II light source, Germany) are presented, with the resolving power of the imaging system being 4 {mu}m in absorption mode and {approx}14 {mu}m in phase contrast mode (z{sub 2}=0.74 m). Thus, phase contrast radiography, combined with numerical forward simulations, is capable of measuring the widths of gaps that are two orders of magnitude thinner than the conventional detection limit.

  13. The IS Services Agency of Wittenheim sets the pace in numerical radiography; L'agence IS Services de Wittenheim a la pointe de la radiographie numerique

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2006-03-15

    Small by its size with only 5 workers, the IS Services Agency of Wittenheim (Alsace) is however ultra specialized in nondestructive testing, and particularly with the new technology of the numerical radiography. (O.M.)

  14. Impact of chest radiography for children with lower respiratory tract infection: a propensity score approach.

    Directory of Open Access Journals (Sweden)

    Emmanuelle Ecochard-Dugelay

    Full Text Available BACKGROUND: Management of acute respiratory tract infection varies substantially despite this being a condition frequently encountered in pediatric emergency departments. Previous studies have suggested that the use of antibiotics was higher when chest radiography was performed. However none of these analyses had considered the inherent indication bias of observational studies. OBJECTIVE: The aim of this work was to assess the relationship between performing chest radiography and prescribing antibiotics using a propensity score analysis to address the indication bias due to non-random radiography assignment. METHODS: We conducted a prospective study of 697 children younger than 2 years of age who presented during the winter months of 2006-2007 for suspicion of respiratory tract infection at the Pediatric Emergency Department of an urban general hospital in France (Paris suburb. We first determined the individual propensity score (probability of having a chest radiography according to baseline characteristics. Then we assessed the relation between radiography and antibiotic prescription using two methods: adjustment and matching on the propensity score. RESULTS: We found that performing a chest radiography lead to more frequent antibiotic prescription that may be expressed as OR = 2.3, CI [1.3-4.1], or as an increased use of antibiotics of 18.6% [0.08-0.29] in the group undergoing chest radiography. CONCLUSION: Chest radiography has a significant impact on the management of infants admitted for suspicion of respiratory tract infection in a pediatric emergency department and may lead to unnecessary administration of antibiotics.

  15. The review of the application of neutron radiography to thermal hydraulic research

    CERN Document Server

    Mishima, K; Saitô, Y; Nakamura, H; Matsubayashi, M

    1999-01-01

    This paper is concerned with the establishment of thermal neutron radiography as a high accuracy measurement method. This paper reviews the present status on the development of high-frame-rate neutron radiography with a steady thermal neutron beam and its application to multiphase flow research performed at the Research Reactor Institute of Kyoto University in collaboration with the Japan Atomic Energy Research Institute.

  16. 75 FR 57080 - In the Matter of Aerotest Operations, Inc. (Aerotest Radiography and Research Reactor); Order...

    Science.gov (United States)

    2010-09-17

    ... COMMISSION In the Matter of Aerotest Operations, Inc. (Aerotest Radiography and Research Reactor); Order... Aerotest Operations, Inc., (Aerotest, the licensee) is the holder of Facility Operating License No. R-98 which authorizes the possession, use, and operation of the Aerotest Radiography and Research Reactor...

  17. 75 FR 39985 - In the Matter of Aerotest Operations, Inc. (Aerotest Radiography and Research Reactor); Order...

    Science.gov (United States)

    2010-07-13

    ... COMMISSION In the Matter of Aerotest Operations, Inc. (Aerotest Radiography and Research Reactor); Order Approving Indirect Transfer of Facility Operating License and Conforming Amendment I. Aerotest Operations..., use and operation of the Aerotest Radiography and Research Reactor (ARRR) located in San Ramon...

  18. 78 FR 46618 - Order Prohibiting Operation of Aerotest Radiography and Research Reactor

    Science.gov (United States)

    2013-08-01

    ... COMMISSION Order Prohibiting Operation of Aerotest Radiography and Research Reactor I. Aerotest Operations... Licensing of Production and Utilization Facilities.'' The license authorizes the operation of the Aerotest Radiography and Research Reactor (ARRR) in accordance with the conditions specified therein. The ARRR is...

  19. 75 FR 27368 - Aerotest Operations, Inc., Aerotest Radiography and Research Reactor; Notice of Consideration of...

    Science.gov (United States)

    2010-05-14

    ... COMMISSION Aerotest Operations, Inc., Aerotest Radiography and Research Reactor; Notice of Consideration of... INFORMATION CONTACT: Cindy Montgomery, Project Manager, Research and Test Reactors Licensing Branch, Division... Operating License No. R-98 for the Aerotest Radiography and Research Reactor (ARRR), currently held by...

  20. Neutron radiography and other NDE tests of main rotor helicopter blades

    CSIR Research Space (South Africa)

    De Beer, FC

    2004-10-01

    Full Text Available leading to aircraft structural failures, are addressed by various NDE techniques. In a combined investigation by means of visual inspection, X-ray radiography and shearography on helicopter main rotor blades, neutron radiography (NRad) at SAFARI-1 research...

  1. 77 FR 43131 - Designation of the Center for Innovation and Technology Cooperation (CITC), Pentane Chemistry...

    Science.gov (United States)

    2012-07-23

    ... Designation of the Center for Innovation and Technology Cooperation (CITC), Pentane Chemistry Industries (PCI... of the Center for Innovation and Technology Cooperation (CITC), Pentane Chemistry Industries (PCI... determined that the Center for Innovation and Technology Cooperation (CITC), Pentane Chemistry Industries...

  2. Rheumatoid arthritis bone erosion volumes on CT and MRI: reliability and correlations with erosion scores on CT, MRI and radiography

    DEFF Research Database (Denmark)

    Møller Døhn, Uffe; Ejbjerg, Bo J; Hasselquist, Maria;

    2007-01-01

    controls underwent unilateral CT, MRI and radiography of second to fifth MCP joints in one hand. Erosion volumes (using OSIRIS software) and scores were determined from CT, MRI and radiography (scores only). RESULTS: CT, MRI and radiography detected 77, 62 and 12 erosions, respectively. On CT, the mean...

  3. Nuclear track radiography of 'hot' aerosol particles

    Energy Technology Data Exchange (ETDEWEB)

    Boulyga, S.F.; Kievitskaja, A.I.; Kievets, M.K.; Lomonosova, E.M.; Zhuk, I.V.; Yaroshevich, O.I.; Perelygin, V.P.; Petrova, R.; Brandt, R.; Vater, P

    1999-06-01

    Nuclear track radiography was applied to identify aerosol 'hot' particles which contain elements of nuclear fuel and fallout after Chernobyl NPP accident. For the determination of the content of transuranium elements in radioactive aerosols the measurement of the {alpha}-activity of 'hot' particles by SSNTD was used in this work, as well as radiography of fission fragments formed as a result of the reactions (n,f) and ({gamma},f) in the irradiation of aerosol filters by thermal neutrons and high energy gamma quanta. The technique allowed the sizes and alpha-activity of 'hot' particles to be determined without extracting them from the filter, as well as the determination of the uranium content and its enrichment by {sup 235}U, {sup 239}Pu and {sup 241}Pu isotopes. Sensitivity of determination of alpha activity by fission method is 5x10{sup -6} Bq per particle. The software for the system of image analysis was created. It ensured the identification of track clusters on an optical image of the SSNTD surface obtained through a video camera and the determination of size and activity of 'hot' particles00.

  4. Magnetic resonance imaging and computed radiography in Achilles tendon rupture

    Energy Technology Data Exchange (ETDEWEB)

    Korenaga, Tateo; Hachiya, Junichi; Miyasaka, Yasuo and others

    1988-11-01

    Magnetic Resonance Imaging (MRI) and Computed Radiography (CR) were performed in 15 patients with complete Achilles tendon rupture who were treated conservatively without surgery. MRI was obtained using Toshiba MRT 50 A superconductive machine, operaing at 0.5 Tesla. CR was performed by CR-101, Fuji Medical System. In fresh cases, ruptured tendons showed intermediate signal intensity on T1-weighted images and high intensity on T2-weighted images. Thickening of the tendon was observed in all cases except in very acute stage. Configuration of thickend tendons tends to be dumbbell shape in subacute stage and fusiform in chronic stage of more than six months after the initial trauma. In cases which showed high signal intensity at the ruptured area both on T1 and T2 weighted images, migration of fat into the sapces between the ruptured tendons was considered to be the major source of increased signal intensity. Computed radiography showed thickening of the tendon, blurring of anterior margin of the tendon, and decreased translucency of pre-Achilles fat pad. However, MRI better demonstrated the details of ruptured tendons when compared to CR, and thought to be an usefull way of following up the healing process of the ruptured tendon to facilitate more reasonable judgement of the time of removing plaster casts and stating exercise.

  5. Stenosis of calcified carotid artery detected on Panoramic Radiography

    Energy Technology Data Exchange (ETDEWEB)

    Cho, So Yang; Oh, Won Mann; Yoon, Suk Ja; Yoon, Woong; Lee, Jae Seo; Kang, Byung Cheol [School of Dentistry, Chonnam National University, Seoul (Korea, Republic of); Palomo, Juan M. [Department of Orthodontics, School of Dental Medicine, Case Western Reserve University, Cleveland (United States)

    2009-09-15

    This study aimed to investigate the luminal stenosis of the internal carotid artery with calcification detected on panoramic radiographs. This study used fifty carotid arteries of 36 dental patients whose panoramic radiograph and computed tomography angiography (CTA) revealed the presence of carotid artery calcification. A neuroradiologist interpreted CTA to determine the degree of stenosis of the internal carotid arteries. The degree of stenosis was stratified in four stages; normal (no stenosis), mild stenosis (1-49%), moderate stenosis (50-69%) and severe stenosis (70-99%). Among the fifty carotid arteries with calcification detected on both panoramic radiography and CTA, 20 carotid arteries (40%) were normal, 29 carotid arteries (18%) had mild stenosis, 1 carotid artery (2%) had moderate stenosis, and there was none with severe stenosis. Sixty percent of the carotid arteries with calcification detected on both panoramic radiography and CTA had internal luminal stenosis, and two percent had moderate stenosis. When carotid atheroma is detected on panoramic radiograph, it is possible that the dental patient has luminal stenosis of the internal carotid artery.

  6. Digital luminescent radiography for diagnosis of skeletal injuries

    Energy Technology Data Exchange (ETDEWEB)

    Buddenbrock, B. [Central Inst. for Radiological Diagnostics, University Hospital of GHS Essen (Germany); Mueller, R.D. [Central Inst. for Radiological Diagnostics, University Hospital of GHS Essen (Germany); John, V. [Central Inst. for Radiological Diagnostics, University Hospital of GHS Essen (Germany); Kock, H.J. [Dept. of Traumatology, University Hospital of GHS Essen (Germany); Hirche, H. [Inst. of Medical Informatics and Biomathematics, Univ. Hospital of GHS Essen (Germany); Voss, M. [Central Inst. for Radiological Diagnostics, University Hospital of GHS Essen (Germany); Loehr, E. [Central Inst. for Radiological Diagnostics, University Hospital of GHS Essen (Germany); Schmit-Neuerburg, K.P. [Dept. of Traumatology, University Hospital of GHS Essen (Germany)

    1992-12-01

    In the course of a comparative study 231 patients with traumatic lesions in skeletal and soft tissue areas were X-rayed using conventional film radiography and digital luminescence radiography (DLR). The results were evaluated by radiologists and traumatologists on the basis of optimised image post-processing in addition to the standard digital presentations. The imaging quality of compacta, spongiosa, soft tissues, fracture lines and osteosynthesis material was assessed in comparison with the screen-film images. Whereas the standard digital presentation in the ``conventionally adjusted`` imaging mode was inferior to the screen-film radiograph, the ``edge-enhanced`` standard presentation proved to be advantageous in the imaging of soft tissues (frequency of first-place ratings: DLR conventional 6%, screen-film system 21%, DLR edge-enhanced 31%). In the overall evaluation high-frequency filtered inverse image post-processing showed the highest diagnostic potential (frequency of first-place ratings: 41%). A conclusive assessment of metal implants is hindered by overshoot artefacts and can only be achieved through time-consuming post-processing of the stored image data. (orig.)

  7. A note on digital dental radiography in forensic odontology.

    Science.gov (United States)

    Chiam, Sher-Lin

    2014-09-01

    Digital dental radiography, intraoral and extraoral, is becoming more popular in dental practice. It offers convenience, such as lower exposure to radiation, ease of storing of images, and elimination of chemical processing. However, it also has disadvantages and drawbacks. One of these is the potential for confusion of the orientation of the image. This paper outlines one example of this, namely, the lateral inversion of the image. This source of confusion is partly inherent in the older model of phosphor storage plates (PSPs), as they allow both sides to be exposed without clue to the fact that the image is acquired on the wrong side. The native software allows digital manipulation of the X-ray image, permitting both rotation and inversion. Attempts to orientate the X-ray according to the indicator incorporated on the plate can then sometimes lead to inadvertent lateral inversion of the image. This article discusses the implications of such mistakes in dental digital radiography to forensic odontology and general dental practice.

  8. Reliability of panoramic radiography in chronological age estimation

    Directory of Open Access Journals (Sweden)

    Ramanpal Singh Makkad

    2013-01-01

    Full Text Available Introduction: There has been a strong relationship between the growth rate of bone and teeth, which can be utilized for the purpose of age identification of an individual. Aims and Objective: The present study was designed to determine the relationship between the dental age, the age from dental panoramic radiography, skeletal age, and chronological age. Materials and Methods: The study included 270 individuals, averaging between 17 years and 25 years of age from out-patient department of New Horizon Dental College and Hospital, Sakri, Bilaspur, Chhattisgarh, India, for third molar surgery. Panoramic and hand wrist radiographs were taken, the films were digitally processed for visualization of the wisdom teeth. The confirmations of ages were repeated again at an interval of 4 weeks by a radiologist. The extracted wisdom teeth were placed in 10% formalin and were examined by one dental surgeon to estimate the age on the basis of root formation. Student′s t-test was adopted for statistical analysis and probability (P value was calculated. Conclusion: Estimating the age of an individual was accurate by examining extracted third molar. Age estimation through panoramic radiography was highly accurate in upper right quadrant (mean = 0.72 and P = 0.077.

  9. Building a cost efficient digital radiography system for educational purposes

    Science.gov (United States)

    Brown, Chris

    Due to the growing need for Medical Physicists, many universities are implementing a Medical Physics program into their academic catalog. To help establish a new program, feasible equipment may be needed to help academic departments provide a hands-on experience for students and help teach the basic concepts of Medical Physics. For example, clinical Digital Radiography Systems (DRS) are used to help teach the basic concepts of digital imaging. However, such systems can cost in excess of 100,000, creating a financial obstacle that will be difficult to overcome. Hence, the development of a cost efficient digital radiography system may be desired in order to eliminate the financial obstacle and give students a hands-on learning experience. This DRS uses three main components to develop an image, an x-ray source, an intensifying plate, and a charge-coupled device (CCD) camera. All three components are housed in a lead-lined box. The purpose of this project is to find the limitations of our DRS and compare the price between our DRS and commercially available DRSs. At optimal settings, a SNR of 25 is shown across the intensifying screen that can identify objects as small as 0.42mm. A Contrast-detail phantom shows the ability to decipher the varying thickness of foam rubber squares. The total cost of our DRS comes to 17,000.00, a fractional price tag compared to a commercially available DRS.

  10. Plausible scenarios for the radiography profession in Sweden in 2025.

    Science.gov (United States)

    Björkman, B; Fridell, K; Tavakol Olofsson, P

    2017-11-01

    Radiography is a healthcare speciality with many technical challenges. Advances in engineering and information technology applications may continue to drive and be driven by radiographers. The world of diagnostic imaging is changing rapidly and radiographers must be proactive in order to survive. To ensure sustainable development, organisations have to identify future opportunities and threats in a timely manner and incorporate them into their strategic planning. Hence, the aim of this study was to analyse and describe plausible scenarios for the radiography profession in 2025. The study has a qualitative design with an inductive approach based on focus group interviews. The interviews were inspired by the Scenario-Planning method. Of the seven trends identified in a previous study, the radiographers considered two as the most uncertain scenarios that would have the greatest impact on the profession should they occur. These trends, labelled "Access to career advancement" and "A sufficient number of radiographers", were inserted into the scenario cross. The resulting four plausible future scenarios were: The happy radiographer, the specialist radiographer, the dying profession and the assembly line. It is suggested that "The dying profession" scenario could probably be turned in the opposite direction by facilitating career development opportunities for radiographers within the profession. Changing the direction would probably lead to a profession composed of "happy radiographers" who are specialists, proud of their profession and competent to carry out advanced tasks, in contrast to being solely occupied by "the assembly line". Copyright © 2017 The College of Radiographers. Published by Elsevier Ltd. All rights reserved.

  11. Inverse-collimated proton radiography for imaging thin materials

    Science.gov (United States)

    Freeman, Matthew S.; Allison, Jason; Andrews, Malcolm; Ferm, Eric; Goett, John J.; Kwiatkowski, Kris; Lopez, Julian; Mariam, Fesseha; Marr-Lyon, Mark; Martinez, Michael; Medina, Jason; Medina, Patrick; Merrill, Frank E.; Morris, Chris L.; Murray, Matthew M.; Nedrow, Paul; Neukirch, Levi P.; Prestridge, Katherine; Rigg, Paolo; Saunders, Alexander; Schurman, Tamsen; Tainter, Amy; Trouw, Frans; Tupa, Dale; Tybo, Josh; Vogan-McNeil, Wendy; Wilde, Carl

    2017-01-01

    Relativistic, magnetically focused proton radiography was invented at Los Alamos National Laboratory using the 800 MeV LANSCE beam and is inherently well-suited to imaging dense objects, at areal densities >20 g cm-2. However, if the unscattered portion of the transmitted beam is removed at the Fourier plane through inverse-collimation, this system becomes highly sensitive to very thin media, of areal densities <100 mg cm-2. Here, this inverse-collimation scheme is described in detail and demonstrated by imaging Xe gas with a shockwave generated by an aluminum plate compressing the gas at Mach 8.8. With a 5-mrad inverse collimator, an areal density change of just 49 mg cm-2 across the shock front is discernible with a contrast-to-noise ratio of 3. Geant4 modeling of idealized and realistic proton transports can guide the design of inverse-collimators optimized for specific experimental conditions and show that this technique performs better for thin targets with reduced incident proton beam emittance. This work increases the range of areal densities to which the system is sensitive to span from ˜25 mg cm-2 to 100 g cm-2, exceeding three orders of magnitude. This enables the simultaneous imaging of a dense system as well as thin jets and ejecta material that are otherwise difficult to characterize with high-energy proton radiography.

  12. Inverse-collimated proton radiography for imaging thin materials.

    Science.gov (United States)

    Freeman, Matthew S; Allison, Jason; Andrews, Malcolm; Ferm, Eric; Goett, John J; Kwiatkowski, Kris; Lopez, Julian; Mariam, Fesseha; Marr-Lyon, Mark; Martinez, Michael; Medina, Jason; Medina, Patrick; Merrill, Frank E; Morris, Chris L; Murray, Matthew M; Nedrow, Paul; Neukirch, Levi P; Prestridge, Katherine; Rigg, Paolo; Saunders, Alexander; Schurman, Tamsen; Tainter, Amy; Trouw, Frans; Tupa, Dale; Tybo, Josh; Vogan-McNeil, Wendy; Wilde, Carl

    2017-01-01

    Relativistic, magnetically focused proton radiography was invented at Los Alamos National Laboratory using the 800 MeV LANSCE beam and is inherently well-suited to imaging dense objects, at areal densities >20 g cm(-2). However, if the unscattered portion of the transmitted beam is removed at the Fourier plane through inverse-collimation, this system becomes highly sensitive to very thin media, of areal densities <100 mg cm(-2). Here, this inverse-collimation scheme is described in detail and demonstrated by imaging Xe gas with a shockwave generated by an aluminum plate compressing the gas at Mach 8.8. With a 5-mrad inverse collimator, an areal density change of just 49 mg cm(-2) across the shock front is discernible with a contrast-to-noise ratio of 3. Geant4 modeling of idealized and realistic proton transports can guide the design of inverse-collimators optimized for specific experimental conditions and show that this technique performs better for thin targets with reduced incident proton beam emittance. This work increases the range of areal densities to which the system is sensitive to span from ∼25 mg cm(-2) to 100 g cm(-2), exceeding three orders of magnitude. This enables the simultaneous imaging of a dense system as well as thin jets and ejecta material that are otherwise difficult to characterize with high-energy proton radiography.

  13. A note on digital dental radiography in forensic odontology

    Directory of Open Access Journals (Sweden)

    Sher-Lin Chiam

    2014-01-01

    Full Text Available Digital dental radiography, intraoral and extraoral, is becoming more popular in dental practice. It offers convenience, such as lower exposure to radiation, ease of storing of images, and elimination of chemical processing. However, it also has disadvantages and drawbacks. One of these is the potential for confusion of the orientation of the image. This paper outlines one example of this, namely, the lateral inversion of the image. This source of confusion is partly inherent in the older model of phosphor storage plates (PSPs, as they allow both sides to be exposed without clue to the fact that the image is acquired on the wrong side. The native software allows digital manipulation of the X-ray image, permitting both rotation and inversion. Attempts to orientate the X-ray according to the indicator incorporated on the plate can then sometimes lead to inadvertent lateral inversion of the image. This article discusses the implications of such mistakes in dental digital radiography to forensic odontology and general dental practice.

  14. Radiography and tomography using fission neutrons at FRM-II

    Energy Technology Data Exchange (ETDEWEB)

    Buecherl, T.; Lierse von Gostomski, Ch. [Inst. fuer Radiochemie, TU-Muenchen, Garching (Germany)

    2004-07-01

    Fission neutrons offer complementary information in radiography and tomography compared to the well established techniques using X-rays, gamma-rays, thermal or cold neutrons. They penetrate thick layers of high density materials with only little attenuation, while for light, specially for hydrogen containing materials, their attenuation is high. In the past, fast neutrons for NDT (non-destructive testing) were only available at accelerator driven systems. These high energy neutrons have to be moderated to achieve acceptable detection efficiencies thus drastically reducing the available neutron intensities and either resulting in a high beam divergence or in additional losses in neutron intensities due to beam collimation. The recently installed neutron computerized tomography and radiography system NECTAR at the Forschungsreaktor Muenchen-II (FRM-II) overcomes these disadvantages by using fission neutrons of about 1.7 MeV mean energy created in two converter plates set-up of highly enriched uranium. The beam quality, i.e. the neutron divergence can be adapted to the object to be measured by using different collimators, resulting in L/D-values up to 300. The available neutron beam intensity at the measuring position is up to 1.7E+08 cm{sup -2} s{sup -1} for a maximum beam area of 40 cm x 40 cm. For conventional imaging a two-dimensional detector system based on a CCD-camera is used, other more specialised systems are available. (author)

  15. Methods for teaching effective patient communication techniques to radiography students.

    Science.gov (United States)

    Makely, S

    1990-07-01

    Teaching students to communicate effectively with patients has always been part of the radiography curriculum in the USA. However, developing these skills has become even more important in recent times due to several factors. Patients who have been well versed in what to expect from the examination being conducted are in a better position to co-operate with the radiographer. This increases the chances of producing optimal results from an examination at the first attempt, thus reducing radiation exposure, patient discomfort and the overall cost of conducting the procedure. Also, increased competition among health care providers has resulted in more emphasis being placed on patient, or customer, satisfaction. Radiographers are in the 'front line' of patient care. Patients often have more interaction with radiographers than with physicians or other medical specialists. Radiographers who practise effective communication techniques with their patients can alleviate anxiety and make an important contribution to the overall satisfaction of the patient with respect to the quality of service and care they receive. This article describes instructional methods being used in the USA to help develop effective patient communication techniques, and reports the findings of a study among radiography educators as to which of these methods are thought to be most successful.

  16. Facial exposure dose assessment during intraoral radiography by radiological technologists

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Hwan; Yang, Han Joon [Dept. of International Radiological Science, Hallym University of Graduate Studies, Chuncheon (Korea, Republic of)

    2014-09-15

    The study examined the changes in the decreased facial exposure dose for radiological technologists depending on increased distance between the workers and the X-ray tube head during intraoral radiography. First, the facial phantom similar to the human tissues was manufactured. The shooting examination was configured to the maxillary molars for adults (60 kVp, 10 mA, 50 msec) and for children (60 kVp, 10 mA, 20 msec), and the chamber was fixed where the facial part of the radiation worker would be placed using the intraoral radiography equipment. The distances between the X-ray tube head and the phantom were set to 10 cm, 15 cm, 20 cm, 25 cm, 30 cm, 35 cm, and 40 cm. The phantom was radiated 20 times with each examination condition and the average scattered doses were examined. The rate at the distance of 40 cm decreased by about 92.6% to 7.43% based on the scattered rays radiated at the distance of 10 cm under the adult conditions. The rate at the distance of 40 cm decreased by about 97.6% to 2.58% based on the scattered rays radiated at the distance of 10 cm under the children conditions. Protection from the radiation exposure was required during the dental radiographic examination.

  17. Manufacturing details by Neutron Radiography of Archaeological Pottery

    Energy Technology Data Exchange (ETDEWEB)

    Bernedo, Alfredo Victor Bellido; Latini, Rose Mary [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil); Souza, Maria Ines Silvani; Vinagre Filho, Ubirajara Maribondo [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2011-07-01

    Full text: The aim of the present work was to investigate manufacturing details of archaeological pot-sherds ceramics by Neutron Radiography. Pottery is perhaps the most important artefact found in excavation. Its archaeological importance relies on the fact that it can reveal cultural traditions and commercial influences in ancient communities. These pottery was recently discovered in archaeological earth circular structures sites in Acre state Brazil and the characteristics of clay used in their manufacture have been studied by modern scientific techniques such as Instrumental Neutron Activation Analysis (INAA), Thermoluminescence Dating and Moessbauer Spectroscopy. Different fragments of pottery were submitted to a neutron flux of the order of 10{sup 5}n.cm{sup -2}2:s{sup -1} for 3 minutes in the research reactor Argonauta at the Instituto de Engenharia Nuclear/CNEN. Digital processing techniques using imaging plate were applied to the image of the selected sample. The Neutrongraphy shows two different manufacturing details: palette and rollers. The fragment made by the technique of palette show a homogeneous mass and the neutrongraphy of ceramic fragments made by the technique of the rollers, pottery funeral, can be seen horizontal traces of the junction of rollers, overlapping, forming layers supported on each other. This technique allows you to create more stable structures. Thus, both the technique of the pallet as the roller can be characterized by Neutron Radiography. (author)

  18. The need for skull radiography in patients presenting for CT

    Energy Technology Data Exchange (ETDEWEB)

    Tress, B.M.

    1983-01-01

    One thousand patients had both CT of the head and a conventional skull series of radiographs. Radiographic findings were abnormal in 250 patients (25%), but only 64 patients (6.4%) had diagnostically significant abnormalities at radiography that were not detected by CT. If the 163 patients who presented after acute trauma were excluded from the series, only 39 (4.7%) of the remaining patients had radiographically significant abnormal findings that were not seen at CT, and only two (0.2%) of these abnormalities could not be diagnosed by a lateral skull radiograph alone. In only five patients (0.5%) was the management actively changed because an abnormaltiy that was detected at skull radiography was not detected at CT. Thus, in nontrauma patients who have stroke, epilepsy, dementia, or non-specific symptoms without focal signs, or have recently undergone craniotomy, and who have been referred for CT, skull radiographs are not justified. In the patient with a history and findings that are strongly suggestive of a pathological disorder anywhere other than in the sella turcica, cerebello-pontine angle, and paranasal sinuses, only the lateral skull radiograph should be obtained after CT, and only if CT is equivocal.

  19. Human-centered design (HCD) of a fault-finding application for mobile devices and its impact on the reduction of time in fault diagnosis in the manufacturing industry.

    Science.gov (United States)

    Kluge, Annette; Termer, Anatoli

    2017-03-01

    The present article describes the design process of a fault-finding application for mobile devices, which was built to support workers' performance by guiding them through a systematic strategy to stay focused during a fault-finding process. In collaboration with a project partner in the manufacturing industry, a fault diagnosis application was conceptualized based on a human-centered design approach (ISO 9241-210:2010). A field study with 42 maintenance workers was conducted for the purpose of evaluating the performance enhancement of fault finding in three different scenarios as well as for assessing the workers' acceptance of the technology. Workers using the mobile device application were twice as fast at fault finding as the control group without the application and perceived the application as very useful. The results indicate a vast potential of the mobile application for fault diagnosis in contemporary manufacturing systems.

  20. Neutron Radiographic Inspection of Industrial Components using Kamini Neutron Source Facility

    Science.gov (United States)

    Raghu, N.; Anandaraj, V.; Kasiviswanathan, K. V.; Kalyanasundaram, P.

    2008-03-01

    Kamini (Kalpakkam Mini) reactor is a U233 fuelled, demineralised light water moderated and cooled, beryllium oxide reflected, low power (30 kW) nuclear research reactor. This reactor functions as a neutron source with a flux of 1012 n/cm2 s-1 at core centre with facilitates for carrying out neutron radiography, neutron activation analysis and neutron shielding experiments. There are two beam tubes for neutron radiography. The length/diameter ratio of the collimators is about 160 and the aperture size is 220 mm×70 mm. Flux at the outer end of the beam tube is ˜106-107 n/cm2 s. The north end beam tube is for radiography of inactive object while the south side beam tube is for radiography of radioactive objects. The availability of high neutron flux coupled with good collimated beam provides high quality radiographs with short exposure time. The reactor being a unique national facility for neutron radiography has been utilized in the examination of irradiated components, aero engine turbine blades, riveted plates, automobile chain links and for various types of pyro devices used in the space programme. In this paper, an overview of the salient features of this reactor facility for neutron radiography and our experience in the inspection of a variety of industrial components will be given.

  1. [Recruiting and Personal Development in Surgical Departments of Large Referral Centers - Current Practice and Options for Improvement from Industry and Service Business].

    Science.gov (United States)

    Homayounfar, K; König, S; Rabe, C; Beck-Broichsitter, B; Lützen, U; Ghadimi, M B; Schmidt, C

    2016-06-23

    Background: Cut-throat competition, cost pressure, generation Y, shortage of qualified staff and feminisation influence human resources management in visceral surgery. The assessment of the current situation by chief surgeons (CS) as well as proof of transferability of strategies from industry and service business (ISB) have not yet been investigated. Material and Methods: The CS of university hospitals and large referral centres (> 800 beds) were interviewed (n = 100) on the basis of a standardised questionnaire including 43 items. Closed questions were designed with a 5-point Likert scale and their analysis was presented as means (MW) and standard deviations (±). Ten human resources manager (HMR) of ISB were invited to participate in 45-minute telephone interviews. Results: Thirty-seven CS participated in the survey, 15 of whom were full professors. Unsolicited applications (100 %), job advertisements (78 %) and direct approaches to final year students (78 %) were the most common ways of recruitment. Only 17 % of CS used a standardised form for preparation. Professional expertise (MW 2.2 ± 0.9), social skills (MW 1.9 ± 0.6) and excellent German language skills (MW 1.8 ± 0.8) were named as important qualifications for employment, while references and certificates were regarded as being less important (MW 3.2 ± 0.9). Personal development was regarded as important (MW 1.1 ± 0.2), but a defined period for residency was not guaranteed (MW 3.0 ± 1.5). Transparent selection criteria for career opportunities (MW 2.5 ± 1.1) and different career models (MW 2.7 ± 1.2) were only rarely available. Six HRM participated in the interviews. Active head-hunting (75 %), Internet platforms (75 %), presentations at conferences (75 %), as well as hiring trainees (50 %), job advertisements (50 %) and social media (50 %) were established options to find qualified employees. Professional and management careers were often

  2. Is radiography justified for the evaluation of patients presenting with cervical spine trauma?

    Energy Technology Data Exchange (ETDEWEB)

    Theocharopoulos, Nicholas; Chatzakis, Georgios; Damilakis, John [Department of Medical Physics, Faculty of Medicine, University of Crete, P.O. Box 2208, Iraklion, 71003 Crete (Greece) and Department of Natural Sciences, Technological Education Institute of Crete, P.O. Box 140, Iraklion 71004 Crete (Greece); Department of Radiology, Faculty of Medicine, University of Crete, P.O. Box 2208, Iraklion, 71003 Crete (Greece); Department of Medical Physics, Faculty of Medicine, University of Crete, P.O. Box 2208, Iraklion, 71003 Crete (Greece)

    2009-10-15

    Conventional radiography has been for decades the standard method of evaluation for cervical spine trauma patients. However, currently available helical multidetector CT scanners allow multiplanar reconstruction of images, leading to increased diagnostic accuracy. The purpose of this study was to determine the relative benefit/risk ratio between cervical spine CT and cervical spine radiography and between cervical spine CT and cervical spine radiography, followed by CT as an adjunct for positive findings. A decision analysis model for the determination of the optimum imaging technique was developed. The sensitivity and specificity of CT and radiography were obtained by dedicated meta-analysis. Lifetime attributable risk of mortal cancer from CT and radiography was calculated using updated organ-specific risk coefficients and organ-absorbed doses. Patient organ doses from radiography were calculated using Monte Carlo techniques, simulated exposures performed on an anthropomorphic phantom, and thermoluminescence dosimetry. A prospective patient study was performed regarding helical CT scans of the cervical spine. Patient doses were calculated based on the dose-length-product values and Monte Carlo-based CT dosimetry software program. Three groups of patient risk for cervical spine fracture were incorporated in the decision model on the basis of hypothetical trauma mechanism and clinical findings. Radiation effects were assessed separately for males and females for four age groups (20, 40, 60, and 80 yr old). Effective dose from radiography amounts to 0.050 mSv and from a typical CT scan to 3.8 mSv. The use of CT in a hypothetical cohort of 10{sup 6} patients prevents approximately 130 incidents of paralysis in the low risk group (a priori fracture probability of 0.5%), 500 in the moderate risk group (a priori fracture probability of 2%), and 5100 in the high risk group (a priori fracture probability of 20%). The expense of this CT-based prevention is 15-32 additional

  3. Computed radiography (FCR) with a dual side reading system. Comparison with conventional radiography for visualization of nodular lung cancers

    Energy Technology Data Exchange (ETDEWEB)

    Ha-kawa, Shangkil; Yoshida, Tsunetaka; Sougawa, Mitsuharu; Harima, Yohko; Sawada, Satoshi [Kansai Medical Univ., Moriguchi, Osaka (Japan)

    2003-02-01

    To assess the diagnostic capability Fuji computed radiography (FCR) using a dual side reading system was compared to the conventional radiography using a film-screen system. Twenty-eight patients with lung cancer were examined with a new FCR system (FCR 5501D) and a conventional screen-film system concurrently. FCR utilizes a reading system that detects emissions from dual sides of imaging plate. Chest X-rays were obtained with same exposure factors in both systems. Image qualities of both systems were compared by two radiologists using a five-level score. There were no lesion that FCR images were inferior to film-screen images. The frequency of score +1 or +2 that FCR images were superior to film-screen images was 31% in large nodular shadows, 40% in accompanying shadows with a nodule, 67% of small nodular shadows, and 43% of the lymph node swelling in the hilum of the lung or mediastinum. In large nodular shadows which were the most frequent abnormality score +1 or +2 were observed in 43% of adenocarcinoma and 26% of squamous cell lung cancer. FCR with the dual side reading system is superior to the conventional screen-film system for visualization of nodular lung cancers. (author)

  4. Diagnostic accuracy of direct digital radiography and conventional radiography for proximal caries detection in primary teeth: A systematic review

    Directory of Open Access Journals (Sweden)

    Sivakumar Nuvvula

    2016-01-01

    Full Text Available Objective: The present study was conducted to uncover the diagnostic accuracy of digital versus conventional radiographic methods for the detection of proximal caries in primary teeth. Methods: Two researchers independently involved in the search process to explore Medical Subject Heading terms "dental digital radiography," "dental radiography," "bitewing," "dental caries," and "primary teeth" using PubMed, Cochrane Library, Ovid SP, and SIGLE databases. Search was confined to the articles published in English language only, with time period limit January 1996 to April 2014 and a hand search was performed to retrieve additional citations. Explicit inclusion and exclusion criteria were applied to eliminate undesired studies. Critical appraisal of the retrieved articles was done using the quality rating based on Bader and co-workers criteria. Results: A total of 129 articles were retrieved, among which 4 articles were included. All the four studies included were in vitro, of which two studies attained a high-quality score, whereas the other two attained average, and low scores based on Bader et al.′s criteria. Conclusions: A big lacuna exists in the literature, regarding the evaluation of radiographic systems in primary teeth, suggesting an immediate need for well conducted in vivo studies. The quality of available evidence can be regarded as fair but cannot be suggested to set a baseline, indicating a need to perform high-quality studies in a randomized sample to find out the accuracy of digital and conventional radiographs.

  5. Industrial diamond

    Science.gov (United States)

    Olson, D.W.

    2001-01-01

    An overview of the industrial diamond industry is provided. More than 90 percent of the industrial diamond consumed in the U.S. and the rest of the world is manufactured diamond. Ireland, Japan, Russia, and the U.S. produce 75 percent of the global industrial diamond output. In 2000, the U.S. was the largest market for industrial diamond. Industrial diamond applications, prices for industrial diamonds, imports and exports of industrial diamonds, the National Defense Stockpile of industrial diamonds, and the outlook for the industrial diamond market are discussed.

  6. Fusion of multi-voltage digital radiography images based on nonsubsampled contourlet transform.

    Science.gov (United States)

    Yanjie, Qi; Liming, Wang

    2016-01-01

    In order to increase the single digital radiography (DR) image information of the composite component in the industry, the different DR images are captured at different voltages so as to get the structural information at different thickness region firstly. Secondly, the original DR images are decomposed by nonsubsampled contourlet transform (NSCT), and the low-frequency subbands are fused by the role of principle component analysis (PCA), and the modified central energy role is used to carry out the high-frequency directional subbands fusion. The false edges are extracted, and the values of the high-frequency subband coefficients of the false edges are set to be a small value so as to reduce the false edges in the fusion image. Finally, the output image can be obtained by inverse nonsubsampled contourlet transform. The experimental results show that the fused DR image brings more detailed information, and the structure of the component can be seen clearly, so it is useful to the fast and accurate quality judgements of the component.

  7. A Study of Gas-Centered Swirl Coaxial Injectors using X-ray Radiography

    Science.gov (United States)

    2012-09-01

    ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NO. Air Force Research Laboratory (AFMC) AFRL/RQRC 10 E. Saturn Blvd. Edwards AFB CA 93524-7680...term • Assuming worst case scenario for disturbance size and that all constants are of order 1: Aerodynamic | Viscous...Approved for public release; distribution unlimited. 15 Mass Weighted Velocity • Droplets across the entire spray are undergoing acceleration in the

  8. Dose audit for patients undergoing two common radiography examinations with digital radiology systems.

    Science.gov (United States)

    İnal, Tolga; Ataç, Gökçe

    2014-01-01

    We aimed to determine the radiation doses delivered to patients undergoing general examinations using computed or digital radiography systems in Turkey. Radiographs of 20 patients undergoing posteroanterior chest X-ray and of 20 patients undergoing anteroposterior kidney-ureter-bladder radiography were evaluated in five X-ray rooms at four local hospitals in the Ankara region. Currently, almost all radiology departments in Turkey have switched from conventional radiography systems to computed radiography or digital radiography systems. Patient dose was measured for both systems. The results were compared with published diagnostic reference levels (DRLs) from the European Union and International Atomic Energy Agency. The average entrance surface doses (ESDs) for chest examinations exceeded established international DRLs at two of the X-ray rooms in a hospital with computed radiography. All of the other ESD measurements were approximately equal to or below the DRLs for both examinations in all of the remaining hospitals. Improper adjustment of the exposure parameters, uncalibrated automatic exposure control systems, and failure of the technologists to choose exposure parameters properly were problems we noticed during the study. This study is an initial attempt at establishing local DRL values for digital radiography systems, and will provide a benchmark so that the authorities can establish reference dose levels for diagnostic radiology in Turkey.

  9. Systematic review of flexion/extension radiography of the cervical spine in trauma patients

    Energy Technology Data Exchange (ETDEWEB)

    Sierink, J.C., E-mail: j.c.sierink@amc.nl [Trauma Unit, Department of Surgery, Academic Medical Center, Meibergdreef 9, 1105 AZ Amsterdam (Netherlands); Lieshout, W.A.M. van, E-mail: w.a.vanlieshout@amc.nl [Trauma Unit, Department of Surgery, Academic Medical Center, Meibergdreef 9, 1105 AZ Amsterdam (Netherlands); Beenen, L.F.M., E-mail: l.f.beenen@amc.nl [Department of Radiology, Academic Medical Center, Meibergdreef 9, 1105 AZ Amsterdam (Netherlands); Schep, N.W.L., E-mail: n.w.schep@amc.nl [Trauma Unit, Department of Surgery, Academic Medical Center, Meibergdreef 9, 1105 AZ Amsterdam (Netherlands); Vandertop, W.P., E-mail: w.p.vandertop@amc.nl [Neurosurgical Center Amsterdam, Academic Medical Center, Meibergdreef 9, 1105 AZ Amsterdam (Netherlands); Goslings, J.C., E-mail: j.c.goslings@amc.nl [Trauma Unit, Department of Surgery, Academic Medical Center, Meibergdreef 9, 1105 AZ Amsterdam (Netherlands)

    2013-06-15

    Introduction: The aim of this review was to investigate whether Flexion/Extension (F/E) radiography adds diagnostic value to CT or MRI in the detection of cervical spine ligamentous injury and/or clinically significant cervical spine instability of blunt trauma patients. Methods: A systematic search of literature was done in Pubmed, Embase and Cochrane Library databases. Primary outcome was sensitivity and specificity of F/E radiography. Secondary outcomes were the positive predicting value (PPV) and negative predicting value (NPV) (with CT or MRI as reference tests due to the heterogeneity of the included studies) of each modality and the quality of F/E radiography. Results: F/E radiography was overall regarded to be inferior to CT or MRI in the detection of ligamentous injury. This was reflected by the high specificity and NPV for CT with F/E as reference test (ranging from 97 to 100% and 99 to 100% respectively) and the ambiguous results for F/E radiography with MRI as its reference test (0–98% and 0–83% for specificity and NPV respectively). Image quality of F/E radiography was reported to have 31 to 70% adequacy, except in two studies which reported an adequacy of respectively 4 and 97%. Conclusion: This systematic review of the literature shows that F/E radiography adds little diagnostic value to the evaluation of blunt trauma patients compared to CT and MRI, especially in those cases where CT or MRI show no indication of ligamentous injury.

  10. SURVEY OF AWARENESS LEVELS OF DENTISTS ABOUT CORRECT USAGE OF VARIOUS RADIOGRAPHIES IN DENTISTRY

    Directory of Open Access Journals (Sweden)

    F Ezoddini Ardakani

    2007-07-01

    Full Text Available Introduction: With the increasing usage of X rays, professional responsibility entails dentists to have sufficient and correct knowledge about prescription of radiographies in order to correctly diagnose and minimally expose patients to radiation. The aim of this study was to assess the awareness levels of dentists in Yazd in term of correct prescription of radiographies. Method: In this descriptive, cross sectional study, specially formatted questionnaires were filled by 134 dentists. Their knowledge in 10 various fields for correct prescription of radiographies was evaluated and compared in each field on the basis of gender and educational status.(General, specialists Results: According to the results, knowledge levels about correct prescription of panoramic, periapical radiographies, CT and MRI was good, while that for occlussal radiographies, patients prone to caries, patients with periodontal diseases, evaluation of growth condition and dental crypts was moderate. In addition, it was weak for bitewing radiographies and in patients not prone to caries. There was no significant difference in awareness levels according to gender. The awareness level of specialists was much higher than that of general dentists except in cases of patients prone to caries where the difference was not significant. Conclusion: One of the most effective means for reducing probable risks of radiation is abstention from prescription of unnecessary radiographies.

  11. [Questions that radiography students have regarding X-ray photography: a qualitative study].

    Science.gov (United States)

    Terashita, Takayoshi; Kisa, Kengo; Oshima, Sumiko; Kawabata, Hidenobu

    2012-01-01

    To improve lectures and training programs on X-ray photography, we aimed to determine the questions that radiography students have regarding X-ray photography. We collected text data from questions on X-ray photography in radiography student reports after an X-ray photography training program. The text data were analyzed using content analysis. Codes were assigned to segments and they were categorized according to similarities. From 111 reports, 348 questions were collected. Four categories and 47 subcategories were obtained. The "Required Knowledge" category comprised subcategories concerning knowledge for the X-ray photography including X-ray radiography methodology and disease knowledge. The "Radiography Service" category comprised subcategories concerning radiographers' responsibilities in a hospital including the role of radiographer and the extent of responsibilities. The "Radiographers' Challenges" category comprised subcategories concerning unusual situations radiographers encounter at work including accurate positioning and communication with patients. The "Patient Types" category comprised subcategories concerning patients in whom X-ray photography was considered difficult including pediatric patients and patients with serious conditions. Questions related to subcategories in "Radiographers' Challenges" and "Patient Types" were interrelated. Radiography students had concerns regarding whether they would be able to handle difficult patients efficiently in clinical situations. We were able to suggest the re-orientation of radiography education according to students' intellectual appetite regarding X-ray radiography.

  12. SHANGHAI INTERNATIONAL INDUSTRIAL FAIR

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ Third Shanghai International Industrial Fair was held in New International Fair Center in Pudong Area in late November. This industrial fair titled "Information and Industrialization" aimed at highlighting China's high technology and industrial achievements in the new century. The sponsors for this session of industrial fair include China State Economic and Trade Commission, Ministry of Foreign Economic and Trade Relations, Ministry of Information Industry, Ministry of Science and Technology, Ministry of Education, Chinese Academy of Sciences and Shanghai Government.CNPC and Sinopec participated in the exhibition displaying a number of the latest technologies such as PetroChina's model for state land resources and Sinopec's model for 300,000-ton ethylene project.

  13. Zhangcha Knitting Industry Features Industrial Cluster Strengths in Shanghai

    Institute of Scientific and Technical Information of China (English)

    Wanzy Wang

    2012-01-01

    As one of the key industrial exhibitions representing knitting industrial development trend and competitiveness in China, the 6th China International Knitting Trade Fair, organized by China National Textile and Apparel Council, undertaken by China Knitting Industry Association (CKIA) and The Sub-Council of Textile Industry, CCPIT (CCPIT TEX), China Wool Textile Association, as well as China Bast and Leaf Fibers Textile Association, kicked off from October 22nd to 24th, 2012 at the Shanghai New International Expo Center,

  14. Radiologic analysis of femoral acetabular impingement: from radiography to MRI

    Energy Technology Data Exchange (ETDEWEB)

    Dwek, Jerry R. [University of California at San Diego, Department of Radiology, Rady Children' s Hospital and Health Center, San Diego, CA (United States); San Diego Imaging, San Diego, CA (United States); Monazzam, Shafagh [Rady Children' s Hospital and Health Center, Department of Orthopedics, San Diego, CA (United States); Chung, Christine B. [University of California at San Diego, Department of Radiology, San Diego, CA (United States)

    2013-03-15

    Femoral acetabular impingement is a set of morphologic abnormalities that are considered to be a major cause of degenerative disease in the hip joint. Early changes are already present in adolescence when it is the pediatric radiologist who must assess current damage with the aim of averting progression to more severe and debilitating osteoarthritis. A multimodality approach is used for diagnosis, that includes conventional radiography and CT to assess the osseous structures. MR arthrography is the primary advanced imaging modality for assessment of morphologic changes as well as injuries of the labrum and articular cartilage. Details of radiologic imaging are offered to guide the radiologist and provide an avenue for the accurate description of the osseous and articular alterations and injury. (orig.)

  15. Inspection of an artificial heart by the neutron radiography technique

    CERN Document Server

    Pugliesi, R; Andrade, M L G; Menezes, M O; Pereira, M A S; Maizato, M J S

    1999-01-01

    The neutron radiography technique was employed to inspect an artificial heart prototype which is being developed to provide blood circulation for patients expecting heart transplant surgery. The radiographs have been obtained by the direct method with a gadolinium converter screen along with the double coated Kodak-AA emulsion film. The artificial heart consists of a flexible plastic membrane located inside a welded metallic cavity, which is employed for blood pumping purposes. The main objective of the present inspection was to identify possible damages in this plastic membrane, produced during the welding process of the metallic cavity. The obtained radiographs were digitized as well as analysed in a PC and the improved images clearly identify several damages in the plastic membrane, suggesting changes in the welding process.

  16. Case study: limitations of panoramic radiography in the anterior mandible.

    LENUS (Irish Health Repository)

    Walker, Cameron

    2009-12-01

    Dental Panoramic Tomography (DPT) is a widely used and valuable examination in dentistry. One area prone to artefacts and therefore misinterpretation is the anterior region of the mandible. This case study discusses a periapical radiolucency related to lower anterior teeth that is discovered to be a radiographic artefact. Possible causes of the artefact include a pronounced depression in the mental region of the mandible or superimposition of intervertebral spaces. Additional limitations of the DPT image include superimposition of radio-opaque structures, reduced image detail compared to intra-oral views and uneven magnification. These problems often make the DPT inappropriate for imaging the anterior mandible. Clinical Relevance: Panoramic radiography is often unsuitable for radiographic examination of the anterior mandible.

  17. Scattering Correction For Image Reconstruction In Flash Radiography

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Liangzhi; Wang, Mengqi; Wu, Hongchun; Liu, Zhouyu; Cheng, Yuxiong; Zhang, Hongbo [Xi' an Jiaotong Univ., Xi' an (China)

    2013-08-15

    Scattered photons cause blurring and distortions in flash radiography, reducing the accuracy of image reconstruction significantly. The effect of the scattered photons is taken into account and an iterative deduction of the scattered photons is proposed to amend the scattering effect for image restoration. In order to deduct the scattering contribution, the flux of scattered photons is estimated as the sum of two components. The single scattered component is calculated accurately together with the uncollided flux along the characteristic ray, while the multiple scattered component is evaluated using correction coefficients pre-obtained from Monte Carlo simulations.The arbitrary geometry pretreatment and ray tracing are carried out based on the customization of AutoCAD. With the above model, an Iterative Procedure for image restORation code, IPOR, is developed. Numerical results demonstrate that the IPOR code is much more accurate than the direct reconstruction solution without scattering correction and it has a very high computational efficiency.

  18. Quantitative shadowgraphy and proton radiography for large intensity modulations

    CERN Document Server

    Kasim, Muhammad Firmansyah; Ratan, Naren; Sadler, James; Chen, Nicholas; Savert, Alexander; Trines, Raoul; Bingham, Robert; Burrows, Philip N; Kaluza, Malte C; Norreys, Peter

    2016-01-01

    Shadowgraphy is a technique widely used to diagnose objects or systems in various fields in physics and engineering. In shadowgraphy, an optical beam is deflected by the object and then the intensity modulation is captured on a screen placed some distance away. However, retrieving quantitative information from the shadowgrams themselves is a challenging task because of the non-linear nature of the process. Here, a novel method to retrieve quantitative information from shadowgrams, based on computational geometry, is presented for the first time. This process can be applied to proton radiography for electric and magnetic field diagnosis in high-energy-density plasmas and has been benchmarked using a toroidal magnetic field as the object, among others. It is shown that the method can accurately retrieve quantitative parameters with error bars less than 10%, even when caustics are present. The method is also shown to be robust enough to process real experimental results with simple pre- and post-processing techn...

  19. Dosimetry and image quality assessment in a direct radiography system

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Bruno Beraldo; Paixao, Lucas; Nogueira, Maria do Socorro, E-mail: boliveira.mg@gmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Oliveira, Marcio Alves de [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Fac. de Medicina. Dept. de Anatomia e Imagem; Teixeira, Maria Helena Araujo [Clinica Dra. Maria Helena Araujo Teixeira, Belo Horizonte, MG (Brazil)

    2014-11-15

    Objective: to evaluate the mean glandular dose with a solid state detector and the image quality in a direct radiography system, utilizing phantoms. Materials and methods: Irradiations were performed with automatic exposure control and polymethyl methacrylate slabs with different thicknesses to calculate glandular dose values. The image quality was evaluated by means of the structures visualized on the images of the phantoms. Results: considering the uncertainty of the measurements, the mean glandular dose results are in agreement with the values provided by the equipment and with internationally adopted reference levels. Results obtained from images of the phantoms were in agreement with the reference values. Conclusion: the present study contributes to verify the equipment conformity as regards dose values and image quality. (author)

  20. Diagnostic radiography of the shoulder. Die Roentgendiagnostik des Schulterguertels

    Energy Technology Data Exchange (ETDEWEB)

    Opitz, G.; Rechl, H. (Klinikum rechts der Isar, Muenchen (Germany, F.R.). Orthopaedische Klinik und Poliklinik); Lehner, K. (Klinikum rechts der Isar, Muenchen (Germany, F.R.). Inst. fuer Roentgendiagnostik)

    1989-06-01

    The frequent complaint about 'pain in the shoulder' is so diffuse that it needs exact clinical and differentiated radiographic examination. The diagnosis 'periarthritis humeroscapularis' can only be given after exclusion of ossous, chondral, or capsular lesions, joint disorders, rotator cuff rupture, or constriction of the subacromial space. Subsequent to antero-posterior and axial, sometimes also tangential, radiography, sonographic examination in many cases already yields the significant information. In case of suspected rotator cuff rupture, the diagnosis can be verified by arthrography or NMR imaging, and labrum defects can well be detected by computed arthro-tomography or NMR imaging. Although sometimes laborious, diagnostic radiology yields the information required to select the suitable conservative or surgical treatment. (orig.).

  1. Ninety-nine years of radiation injuries in dental radiography

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, Kadzuo (Nippon Dental Univ., Niigata (Japan). School of Dentistry at Niigata)

    1994-06-01

    A German dentist, F.O. Walkhoff, has started dental radiography as early as two weeks after Roentgen's discovery on November 8, 1895. The purpose of this paper is to revisit radiation injuries by dividing the era into the era of Kells (before World War II) and the era of low exposure doses (after World War II). Edmund Kells (1856-1928), a pioneer of dental radiologist in the United States, has later become a victim of radiation injuries. During the era of Kells, skin radiation injuries were frequent among the group of dental and medical personnels. In the era of low exposure doses, cancers, leukemia, and genetic effects have begun to receive attention. Radiation injuries occurring in a dental practice are discussed in the context of the two eras. (N.K.) 43 refs.

  2. NECTAR-A fission neutron radiography and tomography facility

    Energy Technology Data Exchange (ETDEWEB)

    Buecherl, T., E-mail: thomas.buecherl@radiochemie.de [Technische Universitaet Muenchen, Lehrstuhl fuer Radiochemie (RCM), Walther-Meissner-Str. 3, 85748 Garching (Germany); Lierse von Gostomski, Ch. [Technische Universitaet Muenchen, Lehrstuhl fuer Radiochemie (RCM), Walther-Meissner-Str. 3, 85748 Garching (Germany); Breitkreutz, H.; Jungwirth, M.; Wagner, F.M. [Technische Universitaet Muenchen, Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRM II) (Germany)

    2011-09-21

    NECTAR (Neutron Computerized Tomography and Radiography) is a versatile facility for radiographic and tomographic investigations as well as for neutron activation experiments using fission neutrons. The radiation sources for this facility are two plates of highly enriched uranium situated in the moderator vessel in FRM II. Thermal neutrons originating from the main fuel element of the reactor generate in these plates fast neutrons. These can escape through a horizontal beam tube without moderation. The beam can be filtered and manipulated in order to reduce the accompanying gamma radiation and to match the specific experimental tasks. A summary of the main parameters required for experimental set-up and (quantitative) data evaluation is presented. The (measured) spectra of the neutron and gamma radiations are shown along with the effect of different filters on their behavior. The neutron and gamma fluxes, dose rates, L/D-ratios, etc. and the main parameters of the actually used detection systems for neutron imaging are given, too.

  3. Chromatically Corrected Imaging Systems for Charged-Particle Radiography

    CERN Document Server

    Blind, Barbara

    2005-01-01

    In proton radiography, imaging with systems consisting of quadrupole magnets is an established technique for viewing the material distribution and composition of objects, either statically or during fast events such as explosions. With the most favorable magnet configuration, the -I lens, chromatic aberrations generally dominate the image blur. Image resolution can be improved, and largely decoupled from the input-beam parameters, by using a second-order achromatic bend with some additional higher-order aberration correction. The aberration-correction approach is discussed. For a given resolution, such a bend allows use of much lower-energy imaging particles than a -I lens. Each bend design represents a set of equivalent systems; an 800-MeV proton design and its equivalent 40-MeV electron system are presented. The electron system is useful for imaging small objects. Magnet errors in the achromatic bends must be tightly controlled to preserve image quality, but not beyond feasibility of present technology. Sys...

  4. Development of Interpretive Simulation Tool for the Proton Radiography Technique

    CERN Document Server

    Levy, M C; Wilks, S C; Ross, J S; Huntington, C M; Fiuza, F; Baring, M G; Park, H- S

    2014-01-01

    Proton radiography is a useful diagnostic of high energy density (HED) plasmas under active theoretical and experimental development. In this paper we describe a new simulation tool that interacts realistic laser-driven point-like proton sources with three dimensional electromagnetic fields of arbitrary strength and structure and synthesizes the associated high resolution proton radiograph. The present tool's numerical approach captures all relevant physics effects, including effects related to the formation of caustics. Electromagnetic fields can be imported from PIC or hydrodynamic codes in a streamlined fashion, and a library of electromagnetic field `primitives' is also provided. This latter capability allows users to add a primitive, modify the field strength, rotate a primitive, and so on, while quickly generating a high resolution radiograph at each step. In this way, our tool enables the user to deconstruct features in a radiograph and interpret them in connection to specific underlying electromagneti...

  5. Practical guidelines for radiographers to improve computed radiography image quality.

    Science.gov (United States)

    Pongnapang, N

    2005-10-01

    Computed Radiography (CR) has become a major digital imaging modality in a modern radiological department. CR system changes workflow from the conventional way of using film/screen by employing photostimulable phosphor plate technology. This results in the changing perspectives of technical, artefacts and quality control issues in radiology departments. Guidelines for better image quality in digital medical enterprise include professional guidelines for users and the quality control programme specifically designed to serve the best quality of clinical images. Radiographers who understand technological shift of the CR from conventional method can employ optimization of CR images. Proper anatomic collimation and exposure techniques for each radiographic projection are crucial steps in producing quality digital images. Matching image processing with specific anatomy is also important factor that radiographers should realise. Successful shift from conventional to fully digitised radiology department requires skilful radiographers who utilise the technology and a successful quality control program from teamwork in the department.

  6. Rethinking responsibility in radiography: Some ethical issues in South Africa

    Directory of Open Access Journals (Sweden)

    Harriet Rosanne Etheredge

    2011-02-01

    Full Text Available The field of radiography in South Africa is complex and presents a multitude of ethical issues. The discipline is often regarded as a supporting function in the healthcare chain, and a stepping-stone in the diagnostic process. This status of the discipline seems to have left many radiographers in a position of substantial confusion. In the course of numerous bioethics presentations for radiographers in South Africa, several ethical and legal issues have recurrently come to my attention. This article aims to address some of these issues and to offer ethically and legally acceptable solutions. The proposed solutions are not absolute – they are based on personal discussions and experiences – and their practicability needs to be scrutinised. Consequently, this article should be seen as a starting point only.

  7. Developing a Massively Parallel Forward Projection Radiography Model for Large-Scale Industrial Applications

    Energy Technology Data Exchange (ETDEWEB)

    Bauerle, Matthew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-08-01

    This project utilizes Graphics Processing Units (GPUs) to compute radiograph simulations for arbitrary objects. The generation of radiographs, also known as the forward projection imaging model, is computationally intensive and not widely utilized. The goal of this research is to develop a massively parallel algorithm that can compute forward projections for objects with a trillion voxels (3D pixels). To achieve this end, the data are divided into blocks that can each t into GPU memory. The forward projected image is also divided into segments to allow for future parallelization and to avoid needless computations.

  8. Imaging Algorithms for Cosmic Ray Muon Radiography Detection of Nuclear Materials

    Institute of Scientific and Technical Information of China (English)

    LIU Yuanyuan; CHEN Zhiqiang; ZHAO Ziran; ZHANG Li; WANG Zhentian

    2009-01-01

    Cosmic ray muon radiography which has good penetration ability and is sensitive to high-Z mate-rials, is an effective method to detect shielded nuclear materials. This paper summarizes methods developed to process muon radiography in Tsinghua University. The methods include detector data correction, recon-struction algorithms (maximum likelihood scattering, MLS, and the maximum likelihood scattering and dis-placement, MLSD) acceleration, and the modification of the normalized mean absolute distance measure (NMADM) into a picture comparison binarization method (PCBM) which is more suitable for cosmic ray muon radiographs. Simulations demonstrate that all these methods give excellent results, so that cosmic muon radiography can become more widely used.

  9. Technical Specifications for the Neutron Radiography Facility (TRIGA Mark 1 Reactor). Revision 6

    Energy Technology Data Exchange (ETDEWEB)

    Tomlinson, R.L.; Perfect, J.F.

    1988-04-01

    These Technical Specifications state the limits under which the Neutron Radiography Facility, with its associated TRIGA Mark I Reactor, is operated by the Westinghouse Hanford Company for the US Department of Energy. These specifications cover operation of the Facility for the purpose of examination of specimens (including contained fissile material) by neutron radiography, for the irradiation of specimens in the pneumatic transfer system and approved in-core or in-pool irradiation facilities and operator training. The Final Safety Analysis Report (TC-344) and its supplements, and these Technical Specifications are the basic safety documents of the Neutron Radiography Facility.

  10. Single-exposure dual-energy computed radiography.

    Science.gov (United States)

    Stewart, B K; Huang, H K

    1990-01-01

    This paper focuses on analysis and development of a single-exposure dual-energy digital radiographic method using computed radiography (Fuji FCR-101 storage phosphor system). A detector sandwich consisting of storage phosphor imaging plates and an interdetector filter is used. The goal of this process is to provide a simple dual-energy method using typical plane-projection radiographic equipment and techniques. This approach exploits the transparency of the storage phosphor plates, using radiographic information that would be otherwise lost, to provide energy selective information essentially as a by-product of the radiographic examination. In order to effectively make use of the large dynamic range of the storage phosphor imaging plates (10,000:1), a computed radiography image reading mode of fixed analog-to-digital converter gain and variable photomultiplier sensitivity provides image data which can be related to relative incident exposure for export to the decomposition algorithm. Scatter rejection requirements necessitated crossed 12:1 grids for a field size of 36 x 36 cm. Optimal technique parameters obtained from computer simulation through minimization of the aluminum and Plexiglas equivalent image uncertainty under conditions of constant absorbed does resulted as: 100 kVp using a 0.15-mm-thick tin (Sn) interdetector filter for the lung field. This yields a surface exposure of 23 mR and a surface absorbed dose of 0.26 mGy for a 23-cm-thick chest. Clinical application in evaluation of the solitary pulmonary nodule is discussed, along with an image set demonstrating this application.

  11. Development of a system for neutron radiography and tomography

    Science.gov (United States)

    Mühlbauer, Martin J.; Calzada, Elbio; Schillinger, Burkhard

    2005-04-01

    Neutron radiography and tomography are getting more and more popular. Since they use the white thermal neutron spectrum, they are especially feasible even at small neutron sources, where the flux is too low for efficient scattering experiments requiring monochromatization of the beam. High-end tomography systems require the investment of several ten thousand Euros, with the costs often hindering the initiative for a new tomography setup. Based on the experiences gathered at Technische Universitaet Muenchen, we developed a cheaper system based on standard components that cannot compete with the sensitivity of a high-grade system, but is perfectly capable of doing neutron radiography and tomography. The system is meant as a startup construction kit for initiating tomography programs even at small neutron sources. The system is built from scratch, enabling the user to gain an understanding for the influence of each component on the image results. With the experience thus gained, he should be able to design his next and more advanced system by himself. To keep the whole system simple and cheap (the price should reach only a few percent of a high-end system), standard parts are used whenever possible, and all components are designed in such a way that they can be built without special equipment. Public domain and freeware software is used for data processing. Such a system is being built at FRM2 in Garching within the scope of a master thesis. After completion, a website will be installed with descriptions, diagrams and software for building and operating the system. Both hardware and software are discussed.

  12. The value of thyroid shielding in intraoral radiography

    Science.gov (United States)

    Hazenoot, Bart; Sanderink, Gerard C H; Berkhout, W Erwin R

    2016-01-01

    Objectives: To evaluate the utility of the application of a thyroid shield in intraoral radiography when using rectangular collimation. Methods: Experimental data were obtained by measuring the absorbed dose at the position of the thyroid gland in a RANDO® (The Phantom Laboratory, Salem, NY) male phantom with a dosemeter. Four protocols were tested: round collimation and rectangular collimation, both with and without thyroid shield. Five exposure positions were deployed: upper incisor (Isup), upper canine (Csup), upper premolar (Psup), upper molar (Msup) and posterior bitewing (BW). Exposures were made with 70 kV and 7 mA and were repeated 10 times. The exposure times were as recommended for the exposure positions for the respective collimator type by the manufacturer for digital imaging. The data were statistically analyzed with a three-way ANOVA test. Significance was set at p Isup, thyroid dose levels were comparable with both collimators at a level indicating primary beam exposure. Thyroid shield reduced this dose with circa 75%. For the Csup position, round collimation also revealed primary beam exposure, and thyroid shield yield was 70%. In Csup with rectangular collimation, the thyroid dose was reduced with a factor 4 compared with round collimation and thyroid shield yielded an additional 42% dose reduction. The thyroid dose levels for the Csup, Psup, Msup and BW exposures were lower with rectangular collimation without thyroid shield than with round collimation with thyroid shield. With rectangular collimation, the thyroid shield in Psup, Msup and BW reduced the dose 10% or less, where dose levels were already low, implying no clinical significance. Conclusions: For the exposures in the upper anterior region, thyroid shield results in an important dose reduction for the thyroid. For the other exposures, thyroid shield augments little to the reduction achieved by rectangular collimation. The use of thyroid shield is to be advised, when performing

  13. Multiscale image processing and antiscatter grids in digital radiography.

    Science.gov (United States)

    Lo, Winnie Y; Hornof, William J; Zwingenberger, Allison L; Robertson, Ian D

    2009-01-01

    Scatter radiation is a source of noise and results in decreased signal-to-noise ratio and thus decreased image quality in digital radiography. We determined subjectively whether a digitally processed image made without a grid would be of similar quality to an image made with a grid but without image processing. Additionally the effects of exposure dose and of a using a grid with digital radiography on overall image quality were studied. Thoracic and abdominal radiographs of five dogs of various sizes were made. Four acquisition techniques were included (1) with a grid, standard exposure dose, digital image processing; (2) without a grid, standard exposure dose, digital image processing; (3) without a grid, half the exposure dose, digital image processing; and (4) with a grid, standard exposure dose, no digital image processing (to mimic a film-screen radiograph). Full-size radiographs as well as magnified images of specific anatomic regions were generated. Nine reviewers rated the overall image quality subjectively using a five-point scale. All digitally processed radiographs had higher overall scores than nondigitally processed radiographs regardless of patient size, exposure dose, or use of a grid. The images made at half the exposure dose had a slightly lower quality than those made at full dose, but this was only statistically significant in magnified images. Using a grid with digital image processing led to a slight but statistically significant increase in overall quality when compared with digitally processed images made without a grid but whether this increase in quality is clinically significant is unknown.

  14. Local-Reference Patient Dose Evaluation in Conventional Radiography Examinations in Mazandaran, Iran

    Directory of Open Access Journals (Sweden)

    Khoshdel-Navi D.

    2016-06-01

    Full Text Available Background: The most efficient application of ionizing radiation is serving medical purposes and using this radiation has caused people to learn that artificial sources of radiation exposure among these resources can be of highest exposure rate. Obiective: The present study is aimed at initially establishing a baseline for localreference dose level in Mazandaran, Iran in 12 projections of the most conventional x-ray examination. Methods: In this study, 13 public hospitals in Mazandaran province were selected for review and required data collected for ten adult patients with mean weight of 70±10kg in each projection. Then, information of each center was separately analyzed. Next, in order to measure x-ray output tube, the dosimeter RTI model Barracuda calibrated has been applied for measuring air karma within energy rage of 40-150kvp. ESAK and ESD parameters, usually used for monitoring DRL in conventional radiography, were calculated. Results: Mean ESDs in this study has been obtained to 1.47±0.98 for skull (PA/ AP, 1.01±0.79 for skull (LAT, 0.67±0.38 for cervical spine (AP, 0.79±0.37 for cervical (LAT, 0.49±0.38 for chest (PA/AP, 1.06±0.44 for chest (LAT, 2.15±0.73 for thoracic spine (AP, 3±0.87 for thoracic spine (LAT, 2.81 ±0.82 for lumbar spine (AP, 4.28±0.78 for lumbar (LAT, 2.07±1.17 for abdomen and 1.90±0.99 for pelvis, respectively. The ESDs calculated for chest examination in both projections, PA and LAT are more than values recommended by the UK (2000, Brazil and Slovenia. Conclusion: The present study has determined wide variations in radiation dose of x-ray examinations among hospitals in Mazandaran, Iran. In order to reduce skin dose, an optimization procedure should be considered. Application of a reference dose (DRL could be a practical method for this purpose. The role of optimization of radiography parameters for reducing patient dose is a significant issue. Through optimizing parameters, it would be possible to

  15. Building And Using A Data Base To Identify Parameters To Further Improve Diagnostic Performance On The Toshiba Computed Radiography System Model 201

    Science.gov (United States)

    Seeley, George W.; Roehrig, Hans; Mockbee, Brent; Hunter, Tim B.; Ovitt, Theron; Claypool, H. R.; Bielland, John C.; Scott, Anne; Yang, Peter; Dallas, William J.

    1987-01-01

    The digital imaging group at the University of Arizona Health Sciences Center Radiology Department is vigorously pursuing the development of a total digital radiology department (TDRD). One avenue of research being conducted is to define the needed resolutions and capabilities of TDRD systems. Parts of that effort are described in these proceedings and elsewhere. One of these investigations is to assess the general application of computed r adiography (CR) in clinical imaging. Specifically we are comparing images produced by the Toshiba computed radiography system (Model 201) to those produced by conventional imaging techniques. This paper describes one aspect of that work.

  16. Comparison of conventional panoramic radiography and panoramic digital subtraction radiography in detection of simulated lesions of mandibular condyle

    Directory of Open Access Journals (Sweden)

    Panjnoush M.

    2008-12-01

    Full Text Available "n  "nBackground and Aim: Digital subtraction Radiography (DSR is a method of accurate assessing condylar head changes. several studies have been carried out in applying DSR in dentistry, however there is a few number of studies in efficacy of DSR method in assesment of condylar head changes, The aim of this study was to compare panoramic radiography and DSR detecting simulated lesions of the mandibular condyl. "nMaterials and Methods: this was a process reaserch study, in which two dry human skulls with no obvious temporomandibular joint pathology were used. Osteophytic lesions were simulated using three sizes of bone chips that were placed on the medial portion of anterior and superolateral aspects of the condyle. Osteolytic lesions were simulated making 1 and 2 mm holes using round burr in the central portion of anterior aspect and Lateral pole of the condyle. Panoramic radiographs were prepared with and without the lesions in place. These paired radiographs were digitized and digital- subtraction images of the original panoramic images were obtained. Eight observers evaluated 155 images of each modality for the presence or absence and the type of simulated lesions of the mandibular condyle. Sensitivity, specificity, reliability and measure of agreement were analyzed using kappa test and crossed tables and qualitative variables were assess by chi-square and fisher's Exact test. "nResults: Specificity of panoramic and DSR methods were 15.4% and 66.7% respectively. Sensitivity of panoramic and DSR methods were 61.1% and 80.6% for osteophytic lesions and 37.5% and 83.3% for Osteolytic lesions. The percentage of correct decisions made in DSR method was significantly more than conventional panoramic method (82.6% vs 41.9% (p<0.0001. "nConclusion: Based on the results of this study digital subtraction technique was significantly more accurate than the panoramic radiographs in detection of simulated lesions of the mandibular condyle.

  17. Education Industry, Spring 2008

    Science.gov (United States)

    2008-01-01

    Homeschooling in the United States: 2003 Statistical Analysis Report indicates that just over 85% of parents chose this option because of concerns...Industrial College of the Armed Forces. Homeschooling in the U.S.,” p. 6. 38 National Center for Educational Statistics, “ Homeschooling in the...Cafarelli, Deborah A. Homeschooling in the U.S. Unpublished manuscript, Industrial College of the Armed Forces, AY 2006-2007. Central Intelligence Agency

  18. 中国入境旅游重心演变与省域空间分异规律%Evolution of the gravity center and spatial differentiation among the provinces of the inbound tourism industry in China

    Institute of Scientific and Technical Information of China (English)

    赵安周; 白凯; 卫海燕

    2011-01-01

    The gravity model,spatial statistical techniques and GIS technology were used to analyze spatial movement of gravity center and spatial differentiation among the provinces about the inbound tourism industry from 1995 to 2009.The results showed:(1) Inbound tourism gravity center of China moves to the southeast in 1995—2000,and it moves to the northeast in 2000—2009;(2) From the global spatial variation,the development level of inbound tourism in different provinces is positive correlated in spatial,the high-value provinces adjacent to other high ones,low-value provinces adjacent to the low ones;(3) From the local Moran,the international tourism revenue of the provinces exists the correlation and heterogeneity in spatial,the level of inbound tourism industry in eastern coastal provinces is better than that in the western provinces.%运用重心模型、空间相关分析和GIS等技术,选取1995—2009年31个省区的面板数据,分析了我国入境旅游重心的空间移动和不同省区入境旅游发展的空间分异.结果表明:(1)1995—2000年,中国入境旅游重心呈现东偏南移动的趋势,2000—2009年呈现东偏北移动趋势;(2)从全局空间分异上来看,各省区入境旅游发展表现出空间集聚性,国际旅游收入较高的省区在空间上趋于相邻,国际旅游收入较低的省区在空间上趋于相邻;(3)就局部Moran指数来看,我国各省区国际旅游收入之间存在一定的空间相关性和异质性,入境旅游

  19. Federal laboratory nondestructive testing research and development applicable to industry

    Energy Technology Data Exchange (ETDEWEB)

    Smith, S.A.; Moore, N.L.

    1987-02-01

    This document presents the results of a survey of nondestructive testing (NDT) and related sensor technology research and development (R and D) at selected federal laboratories. Objective was to identify and characterize NDT activities that could be applied to improving energy efficiency and overall productivity in US manufacturing. Numerous federally supported R and D programs were identified in areas such as acoustic emissions, eddy current, radiography, computer tomography and ultrasonics. A Preliminary Findings Report was sent to industry representatives, which generated considerable interest.

  20. A technique for estimating one-dimensional diffusion coefficients in low-permeability sedimentary rock using X-ray radiography: comparison with through-diffusion measurements.

    Science.gov (United States)

    Cavé, Lisa; Al, Tom; Xiang, Yan; Vilks, Peter

    2009-01-07

    The measurement of diffusive properties of low-permeability rocks is of interest to the nuclear power industry, which is considering the option of deep geologic repositories for management of radioactive waste. We present a simple, non-destructive, constant source in-diffusion method for estimating one-dimensional pore diffusion coefficients (D(p)) in geologic materials based on X-ray radiography. Changes in X-ray absorption coefficient (Deltamicro) are used to quantify changes in relative concentration (C/C(0)) of an X-ray attenuating iodide tracer as the tracer solution diffuses through the rock pores. Estimated values of D(p) are then obtained by fitting an analytical solution to the measured concentration profiles over time. Measurements on samples before and after saturation with iodide can also be used to determine iodide-accessible porosity (phi(I)). To evaluate the radiography method, results were compared with traditional steady-state through-diffusion measurements on two rock types: shale and limestone. Values of D(p) of (4.8+/-2.5)x10(-11) m(2).s(-1) (mean+/-standard deviation) were measured for samples of Queenston Formation shale and (2.6+/-1.0)x10(-11) m(2).s(-1) for samples of Cobourg Formation limestone using the radiography method. The range of results for each rock type agree well with D(p) values of (4.6+/-2.0)x10(-11) m(2).s(-1) for shale and (3.5+/-1.8)x10(-11) m(2).s(-1) for limestone, calculated from through-diffusion experiments on adjacent rock samples. Low porosity (0.01 to 0.03) and heterogeneous distribution of porosity in the Cobourg Formation may be responsible for the slightly poorer agreement between radiography and through-diffusion results for limestones. Mean values of phi(I) for shales (0.060) and limestones (0.028) were close to mean porosity measurements made on bulk samples by the independent water loss technique (0.062 and 0.020 for shales and limestones, respectively). Radiography measurements offer the advantage of time

  1. Assessment and Comparison of Impacted Maxillary Canine Position in Panoramic Radiography with CBCT

    Directory of Open Access Journals (Sweden)

    F Ezoddiniardakani

    2015-05-01

    Conclusion: The study findings revealed that the angulation and magnification methods were not reliable in order to assess the impacted maxillary canines in panoramic radiography, though Angulation proved to be more successful than magnification method.

  2. Comparison study on CNR and SNR of thoracic spine lateral radiography

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Won [Dept. of Radiology, Samsung Medical Center, Seoul (Korea, Republic of); Min, Jung Whan; Lyu, Kwang Yeul [Dept. of Radiology, Shingu University, Sungnam (Korea, Republic of); Kim, Jung Min [Dept. of Radiological Science, College of Health Science, Korea University, Seoul (Korea, Republic of); Jeong, Hei Woun [Dept. of Radiological Science, Beakseok Culture University, Cheonan (Korea, Republic of); Lee, Joo Ah [Dept. of Oncology, Catholic University of Korea Incheon St.Mary,s Hospital, Incheon (Korea, Republic of); Jung, Jae Hong [Dept. of Oncology, Soonchunhyang University Bucheon Hospital, Bucheon (Korea, Republic of); Sung, Dong Chan [Dept. of Radiology, Dong Guk University Medical Center, Seoul (Korea, Republic of); Park, Soon Cheol [Dept. of Radiology, Kang Dong Kyung Hee University Medical Center, Seoul (Korea, Republic of)

    2013-12-15

    This study was proven for the T-spine breathing technique in lateral projection, using computer radiography (CR), charge coupled device (CCD), indirect digital radiography (IDR) and direct digital radiography (DDR). All images were evaluated and compared with CNR and SNR measured with the mean pixels and the standard deviation as setting ROI of spinous process, pedicle, vertebral body, intervertebral foramen and intervertebral disk using Image J. In experiment results of 4 type detectors, T-spine breathing technique was indicated as excellent in ROI of spinous process, pedicle, vertebral body, intervertebral foramen and intervertebral disk. As T-spine breathing technique indicated excellent images compared to the existing T-spine lateral radiography, this method would be useful for elderly patients who have difficulty in deep exhalation. This study was indicated the application possibility of T-spine breathing technique by presenting contrast to noise ratio (CNR) and signal to noise ratio (SNR) with quantitative value in 4 type detectors.

  3. Inspection of CF188 composite flight control surfaces with neutron radiography

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, W.J.; Bennett, L.G.I. [Royal Military Coll. of Canada, Kingston, Ontario (Canada). Dept. of Chemistry and Chemical Engineering; Mullin, S.K. [Aerospace and Telecommunications Engineering Support Squadron, Astra, Ontario (Canada). Nondestructive Testing Center Development Section

    1996-12-31

    At the Royal Military College of Canada`s SLOWPOKE-2 Facility, a neutron radiography facility has been designed and installed using a small (20kWth), pool-type research reactor called the SLOWPOKE-2 (Safe Low Power c(K)ritical Experiment) as the neutron source. Since then, the research has continued along two fronts: developing applications and improving the quality of the neutron beam. The most interesting applications investigated to date has been the inspection of various metal ceramic composites and the inspection of the composite flight control surfaces of some of the CF188 Hornet aircraft. As part of the determination of the integrity of the aircraft, it was decided to inspect an aircraft with the highest flight house using both X- and neutron radiography. The neutron radiography and, to a lesser extent, X-radiography inspections completed at McClellan AFB revealed 93 anomalies. After returning to Canada, the component with the greatest structural significance, namely the right hand rudder from the vertical stabilizer, was removed from the aircraft and put through a rigorous program of numerous NDT inspections, including X-radiography (film and real-time), eddy current, ultrasonics (through transmission and pitch-catch), infrared thermography, and neutron radiography. Therefore, of all the techniques investigated, only through transmission ultrasonics and neutron radiography were able to identify large areas of hydration. However, only neutron radiography could identify the small areas of moisture and hydration. Given the structural significance of the flight control surfaces in modern fighter aircraft, even the smallest amounts of hydration could potentially lead to catastrophic results.

  4. Interpretation of Core Length in Shear Coaxial Rocket Injectors from X-ray Radiography Measurements

    Science.gov (United States)

    2014-06-01

    Shear Coaxial Rocket Injectors from X-ray Radiography Measurements 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...ASME/SAE/ASEE Joint Propulsion Conference, Cleveland, OH, 28-30 July, 2014. PA#14340 14. ABSTRACT Shear coaxial injectors are so named because they...Length in Shear Coaxial Rocket Injectors from X-ray Radiography Measurements S. Alexander Schumaker1, Stephen A. Danczyk2 and Malissa D.A. Lightfoot2

  5. A Review of Full-Body Radiography in Nontraumatic Emergency Medicine

    OpenAIRE

    2012-01-01

    This paper reports on the application of full-body radiography to nontraumatic emergency situations. The Lodox Statscan is an X-ray machine capable of imaging the entire body in 13 seconds using linear slit scanning radiography (LSSR). Nontraumatic emergency applications in ventriculoperitoneal (VP) shunt visualisation, emergency room arteriography (ERA), detection of foreign bodies, and paediatric emergency imaging are presented. Reports show that the fast, full-body, and low-dose scanning c...

  6. A review of full-body radiography in nontraumatic emergency medicine

    OpenAIRE

    2012-01-01

    This paper reports on the application of full-body radiography to nontraumatic emergency situations. The Lodox Statscan is an X-ray machine capable of imaging the entire body in 13 seconds using linear slit scanning radiography (LSSR). Nontraumatic emergency applications in ventriculoperitoneal (VP) shunt visualisation, emergency room arteriography (ERA), detection of foreign bodies, and paediatric emergency imaging are presented. Reports show that the fast, full-body, and low-dose scanning c...

  7. Design of a mobile neutron radiography installation based on a compact sealed tube neutron generator

    Institute of Scientific and Technical Information of China (English)

    MaWei-Chao; YaoAn-Ju; 等

    1997-01-01

    A series of optimum conditions are taken into account in the construction of neutron radiography(NR) installation based on a sealed tube neutron generator capable of gnerating 1010 n/s with 14MeV.The characteristics of NNU screens,a kind of self-made 6LiF.ZnS(Ag)scintillation intensifying screen are presented.Finally,some neutron radiographies taken by this NR installation and NNU screens are given.

  8. Center for Creative Studies, Detroit

    Science.gov (United States)

    AIA Journal, 1976

    1976-01-01

    One of the ten buildings chosen to receive 1976 AIA honor awards, the arts center houses the departments of sculpture, painting, graphics, advertising art, photography, and industrial design. (Author/MLF)

  9. Electricity Infrastructure Operations Center (EIOC)

    Data.gov (United States)

    Federal Laboratory Consortium — The Electricity Infrastructure Operations Center (EIOC) at PNNL brings together industry-leading software, real-time grid data, and advanced computation into a fully...

  10. Center for Creative Studies, Detroit

    Science.gov (United States)

    AIA Journal, 1976

    1976-01-01

    One of the ten buildings chosen to receive 1976 AIA honor awards, the arts center houses the departments of sculpture, painting, graphics, advertising art, photography, and industrial design. (Author/MLF)

  11. A transportable neutron radiography system based on a SbBe neutron source

    Science.gov (United States)

    Fantidis, J. G.; Nicolaou, G. E.; Tsagas, N. F.

    2009-07-01

    A transportable neutron radiography system, incorporating a SbBe neutron source, has been simulated using the MCNPX code. Design provisions have allowed two radiography systems to be utilised using the same SbBe neutron source. In this respect, neutron radiographies can be carried out using the photoneutrons produced when the 124Sb is surrounded by the Be target. Alternatively, γ-radiography can be utilised with the photons from the 124Sb with the target removed. Appropriate collimators were simulated for each of the radiography modes. Apart from Be, the materials considered were compatible with the European Union Directive on 'Restriction of Hazardous Substances' (RoHS) 2002/95/EC, hence excluding the use of cadmium and lead. Bismuth was chosen as the material for γ-radiation shielding and the proposed system allowed a maximum activity of the 124Sb up to 1.85×1013 Bq. The system simulated allows different object sizes to be studied with a wide range of radiography parameters.

  12. An experimental comparative study of radiography, ultrasonography and CT imaging in the IV catheter fragment

    Energy Technology Data Exchange (ETDEWEB)

    Kweon, Dae Cheol [Dept. of Radiological Science, College of Health Science, Shinhan University, Uijeongbu (Korea, Republic of)

    2016-06-15

    The objective of this study was to detect the fragments generated during IV (intravenous) catheter injection of contrast medium and drug administration in a clinical setting and removal was performed by experimentally producing a phantom, and to compare the radiography, ultrasonography, and multi-detector computed tomography (MDCT) imaging and radiation dose. A 1 cm fragment of an 18 gage Teflon® IV catheter with saline was inserted into the IV control line. Radiography, CT, and ultrasonography were performed and radiography and CT dose were calculated. CT and ultrasonography showed an IV catheter fragment clinically and radiography showed no visible difference in the ability to provide a useful image of an IV catheter fragment modality (p >.05). Radiography of effective dose (0.2139 mSv·Gy-1·cm-2) form DAP DAP (0.93 μGy·m2 ), and dose length product (DLP) (201 mGy·cm) to effective dose was calculated as 0.483 mSv. IV catheter fragment were detected of radiography, ultrasonography and CT. These results can be obtained by menas of an excellent IV catheter fragment of detection capability CT. However, CT is followed by radiation exposure. IV catheter fragment confirming the position and information recommend an ultrasonography.

  13. Twenty-degree-tilt radiography for evaluation of lateral humeral condylar fracture in children

    Energy Technology Data Exchange (ETDEWEB)

    Imada, Hideaki; Tanaka, Ryuji; Itoh, Yohei; Kishi, Kazuhiko [National Hospital Organization, Higashi-Hiroshima Medical Center, Department of Orthopedic Surgery, Higashi Hiroshima, Hiroshima (Japan)

    2010-03-15

    To investigate the efficacy of '20 -tilt anteroposterior (A-P) radiography' in the assessment of lateral condylar fractures of the distal humerus. Eighteen children with lateral humeral condylar fractures were studied. Every child underwent conventional A-P and lateral radiography, and six children underwent multi-detector computed tomography (MDCT). For the investigation of 20 -tilt radiography, ten children with lateral humeral condylar fractures had conventional and 20 -tilt A-P and lateral radiography both preoperatively and postoperatively. Fragment dislocation was measured at the lateral and medial margins of the fracture on both the conventional A-P and 20 -tilt A-P radiographs. The lateral condylar fragment was triangular and was most prominent posteriorly. The fracture line was typically tilted approximately 20 to a reference line perpendicular to the long axis of the humerus in the lateral view. The extent of dislocation at the lateral and medial margins of the fracture site by 20 -tilt A-P radiography (9.3 {+-} 3.6 mm and 5.6 {+-} 2.5 mm) was significantly wider than that measured by the conventional method (6.8 {+-} 4.1 mm and 2.0 {+-} 1.5 mm), which may influence treatment. Twenty-degree-tilt A-P radiography may more precisely demonstrate fragment dislocation than standard radiographs and may influence patient treatment. (orig.)

  14. Whole-body MRI of Langerhans cell histiocytosis: comparison with radiography and bone scintigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Goo, Hyun Woo; Yang, Dong Hyun [Asan Medical Center, Department of Radiology, University of Ulsan College of Medicine, Seoul (Korea); Ra, Young Shin [Asan Medical Center, Department of Neurosurgery, University of Ulsan College of Medicine, Seoul (Korea); Song, Joon Sup; Im, Ho Joon; Seo, Jong Jin; Ghim, Thad; Moon, Hyung Nam [Asan Medical Center, Department of Pediatric Oncology, University of Ulsan College of Medicine, Seoul (Korea)

    2006-10-15

    In Langerhans cell histiocytosis (LCH) evaluation of the extent of disease is one of the major predictors of patient outcome. Historically this is undertaken using plain radiography and bone scintigraphy. Recently, whole-body (WB) MRI has been reported to be useful in detecting skeletal and extraskeletal metastases in both adults and children. To evaluate the usefulness of WB MRI in patients with LCH in comparison with plain radiography and bone scintigraphy. In nine children (1-7 years of age; mean 3.3 years) who had a pathological diagnosis of LCH and had either plain radiography or bone scintigraphy for comparison, 43 WB MR examinations were performed. Skeletal and extraskeletal lesions of the disease on WB MRI were compared with those on plain radiography and bone scintigraphy. LCH showed unifocal single-system involvement in one patient, multifocal single-system involvement in three, and multifocal multisystem disease in five. WB MRI identified additional skeletal lesions in three (38%) of eight patients, compared with plain radiography, and in two (25%) of eight, compared with bone scintigraphy. WB MRI detected extraskeletal lesions of the disease in five (56%) of the nine patients exclusively, except for one patient whose lung lesions were also detected on plain radiography. In two patients, treatment was changed according to WB MRI findings. (orig.)

  15. Designing Thought of Green Demonstration Building of Zhengzhou Energy-saving and Environmental Protection Industry Incubation Center%郑州节能环保产业孵化中心绿色示范楼设计思路

    Institute of Scientific and Technical Information of China (English)

    贺栋; 韦峰

    2015-01-01

    在建筑能耗与污染严重的现今社会,建筑设计仅仅从使用功能、形体美学等方面考虑是不够全面的。绿色建筑作为适应当今社会趋势的建筑形式备受人们瞩目。本文以郑州节能环保产业孵化中心绿色示范楼的绿色设计理念和建筑形态成因为对象,对其进行评论。%In the present society with high energy consumption and serious pollution,the buildings cannot only be considered from the aspects of function and aesthetics, which is not comprehensive enough. Green building, as an ar⁃chitectural form adapting to the trend in today's society has been paid much attention to. Taking the green demonstra⁃tion building of Zhengzhou energy-saving and environmental protection industry incubator center as the reasearch ob⁃ject,the article discussed its design concept and architectural form causes.

  16. Training Centers for Onsite Wastewater Treatment

    Science.gov (United States)

    Onsite wastewater training centers offer classes, demonstration projects and research facilities for onsite industry professionals. Classes include wastewater management, new technologies and pre-licensing.

  17. Industry Employment

    Science.gov (United States)

    Occupational Outlook Quarterly, 2012

    2012-01-01

    This article illustrates projected employment change by industry and industry sector over 2010-20 decade. Workers are grouped into an industry according to the type of good produced or service provided by the establishment for which they work. Industry employment projections are shown in terms of numeric change (growth or decline in the total…

  18. Diagnosis of Nasopharyngeal Obstruction by Lateral Cephalometric Radiography

    Directory of Open Access Journals (Sweden)

    H. Ravanmehr

    2005-06-01

    Full Text Available Statement of Problem: Nasopharyngeal obstruction by adenoid enlargement is one of the main causes of mouth breathing. Diagnostic indices of nasopharyngeal obstruction by lateral cephalometric radiography are controversial.Purpose: The purpose of this study was to diagnose the nasopharyngeal obstruction by means of lateral cephalometric radiography.Materials and Methods: In this research two groups, (study and control, of 6 to 15 years old were studied. In the study group, 46 mouth breathers were clinically examined by an orthodontist and an Otolaryngologist to confirm the nasopharyngeal obstruction.Control group was also comprised of 46 nasal breathers within the same age groups. A lateral cephalogram in centric occlusion was obtained for each patient. After tracing,following 7 nasopharyngeal variables were measured: 1- pp (palatopharyngeal depth.2- Ad.Pmp (nasopharyngeal airway depth. 3- Air area (nasopharyngeal airway area. 4-NP area (bony area of nasopharynx. 5- Ba.Pmp (bony depth of nasopharynx. 6- d(bony depth of nasopharynx. 7- h (bony height of nasopharynx.Statistical t-test was conducted following calculating the mean, standard deviation and p-value of parameters. Discriminant function analysis was employed subsequent to thet-test for the significant variables, in order to find a method by which the values for several variables could be used simultaneously to determine whether obstruction exists.Qualitative variables of sex and age groups (6-10, 11-12, and 13-15 years old were alsoused in discriminant analysis.Results: In the study group, mean value of pp, Ad.pmp, air area, Np area and Ba.pmp were significantly decreased, whereas mean of d and h variables were not considerably lessened. After performing analysis stage, the following discriminant function equationwith critical point of 3.88 and correct classification of 94.57% was determined:D=0.345 (pp +0.064 (Ad.pmp-0.001(NP area + 0.03(Air area +0.505(Age1.If a person’s age is

  19. AIRIX: a new tool for flash radiography in detonics

    Science.gov (United States)

    Cavailler, Claude

    2001-04-01

    AIRIX is an induction linear accelerator which will be used for flash radiography in Commissariat A L'Energie Atomique In France. Designed to produce an X-ray dose of some hundreds Rads at 1 meter with an X-ray focal spot size diameter of less than 2 mm (LANL-CEA DAM definition), this facility consists in a 3,8 MeV/2 kA pulsed electron injector and 15,4 MeV induction accelerator powered by 32 high voltage generators. A prototype of this accelerator, called PIVAIR, has been studied and realized in CEA CESTA near Bordeaux. PIVAIR is a validation step for AIRIX at 8 MeV. It includes an injector (3,6 MeV, 3,2 kA, 60 ns) and 16 induction cells supplied by 8 high voltage generators (250 kV, 70 ns). Two different technologies of induction cells have been tested (Rexolite insulator or ferrite Under Vacuum). We have chosen ferrite under vacuum cells technology after comparison of results on beam transport and reliability tests. A focusing experiment at 7.2 MeV of the electron beam has been achieved during summer 1997. We have begun to produce X-rays in October 1997. A dose level of 50 Rad at 1 meter has been achieved with an X-ray spot size diameter of 3.5 to 4 mm (LANL-CEA DAM definition). Static flash radiography of very dense object have been achieved from November 1997 until February 1998. We have been able to test in situ new kinds of very high sensitive X-ray detectors and to check they had reached our very ambitious goals: quantum efficiency at 5 MeV > 50% instead of 1% for luminous screens and film, sensitivity radiographic luminous screens and films), dynamic range > 100, resolution radiograph of the device explosion under test with the high stopping power detector located in a blast protection set behind the device. In this communication we will present all these techniques which correspond to a significant effort of CEA begun in 1992. AIRIX facility will be available to run detonics experiments before end of 2000.

  20. International Water Center

    Science.gov (United States)

    The urban district of Nancy and the Town of Nancy, France, have taken the initiative of creating an International Center of Water (Centre International de l'Eau à Nancy—NAN.C.I.E.) in association with two universities, six engineering colleges, the Research Centers of Nancy, the Rhine-Meuse Basin Agency, and the Chamber of Commerce and Industry. The aim of this center is to promote research and technology transfer in the areas of water and sanitation. In 1985 it will initiate a research program drawing on the experience of 350 researchers and engineers of various disciplines who have already been assigned to research in these fields. The research themes, the majority of which will be multidisciplinary, concern aspects of hygiene and health, the engineering of industrial processes, water resources, and the environment and agriculture. A specialist training program offering five types of training aimed at university graduates, graduates of engineering colleges, or experts, will start in October 1984.

  1. Contrast-Enhanced Proton Radiography for Patient Set-up by Using X-Ray CT Prior Knowledge

    Energy Technology Data Exchange (ETDEWEB)

    Spadea, Maria Francesca, E-mail: mfspadea@unicz.it [Department of Experimental and Clinical Medicine, Magna Graecia University, Catanzaro (Italy); Fassi, Aurora [Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milano (Italy); Zaffino, Paolo [Department of Experimental and Clinical Medicine, Magna Graecia University, Catanzaro (Italy); Riboldi, Marco; Baroni, Guido [Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milano (Italy); Bioengineering Unit—CNAO Foundation, Pavia (Italy); Depauw, Nicolas [Department of Radiation Oncology, Harvard Medical School and Massachusetts General Hospital, Boston, Massachusetts (United States); Centre for Medical Radiation Physics, University of Wollongong, Wollongong (Australia); Seco, Joao [Department of Radiation Oncology, Harvard Medical School and Massachusetts General Hospital, Boston, Massachusetts (United States)

    2014-11-01

    Purpose: To obtain a contrasted image of the tumor region during the setup for proton therapy in lung patients, by using proton radiography and x-ray computed tomography (CT) prior knowledge. Methods and Materials: Six lung cancer patients' CT scans were preprocessed by masking out the gross tumor volume (GTV), and digitally reconstructed radiographs along the planned beam's eye view (BEV) were generated, for a total of 27 projections. Proton radiographies (PR) were also computed for the same BEV through Monte Carlo simulations. The digitally reconstructed radiograph was subtracted from the corresponding proton image, resulting in a contrast-enhanced proton radiography (CEPR). Michelson contrast analysis was performed both on PR and CEPR. The tumor region was then automatically segmented on CEPR and compared to the ground truth (GT) provided by physicians in terms of Dice coefficient, accuracy, precision, sensitivity, and specificity. Results: Contrast on CEPR was, on average, 4 times better than on PR. For 10 lateral projections (±45° off of 90° or 270°), although it was not possible to distinguish the tumor region in the PR, CEPR offers excellent GTV visibility. The median ± quartile values of Dice, precision, and accuracy indexes were 0.86 ± 0.03, 0.86 ± 0.06, and 0.88 ± 0.02, respectively, thus confirming the reliability of the method in highlighting tumor boundaries. Sensitivity and specificity analysis demonstrated that there is no systematic over- or underestimation of the tumor region. Identification of the tumor boundaries using CEPR resulted in a more accurate and precise definition of GTV compared to that obtained from pretreatment CT. Conclusions: In most proton centers, the current clinical protocol is to align the patient using kV imaging with bony anatomy as a reference. We demonstrated that CEPR can significantly improve tumor visualization, allowing better patient set-up and permitting image guided proton therapy (IGPT)

  2. Industrial Chain: Industrial Vertical Definition

    Institute of Scientific and Technical Information of China (English)

    YifeiDu; GuojunJiang; ShimingLi

    2004-01-01

    Like value chain and supply chain, “industrial chain” becomes the focus of attention. The implication of “industrial chain” has gained a large range of extension. It not only expresses the industrial “chain” structure and relationship of “back and forward”in order or “up and down” in direction, but also it represents a cluster of large scale of firms in an area or colony. It is a network, or a community. Consequently, we conclude that “industrial chain” is a synthesis of industrial chain, industrial cluster, or industrial network.In this article, firstly we will distinguish industry chain from industry. An industry is the collection of firms that have the same attribute, so an industry can be defined by firm collection of certain attribute. We indicate that industrial chain is a kind of vertical and orderly industrial link. It is defined according to a series of specific product or service created. Secondly we analyze the vertical orderly defiinition process from the aspects of social division of labor and requirement division, self-organization system, and value analysis.Non-symmetry and depending on system or community of large scale of industrial units lead to entire industry to “orderly” structure. On the other hand, the draught of diversity and complexity of requirement simultaneously lead to entire industry to be more “orderly”. Along with processes of self-organization, industrial will appi'oach the state of more orderly and steady, and constantly make industrial chain upgrade. Each firm or unit, who will gain the value, has to establish channels of value, which we called “industrial value chain”. Lastly,we discuss the consequence of vertical and orderly definition, which is exhibited by a certain relationship body. The typical forms of industrial chain include industrial cluster, strategy alliance and vertical integration etc.

  3. Directory of Manufacturing Research Centers

    Science.gov (United States)

    1989-06-01

    L. Lehn P. Klinefelter A DoD Information Analysis Center UNCLASSIFIED ECURITY CLASSIFICATION OF THIS PAGE REPORT DOCUMENTATION PAGE a. REPORT...in R&D, industrial innovation case histories , and managing innovation. Industry recognizes that research and development are indispensable to the

  4. Photon counting detector for the personal radiography inspection system "SIBSCAN"

    Science.gov (United States)

    Babichev, E. A.; Baru, S. E.; Grigoriev, D. N.; Leonov, V. V.; Oleynikov, V. P.; Porosev, V. V.; Savinov, G. A.

    2017-02-01

    X-ray detectors operating in the energy integrating mode are successfully used in many different applications. Nevertheless the direct photon counting detectors, having the superior parameters in comparison with the integrating ones, are rarely used yet. One of the reasons for this is the low value of the electrical signal generated by a detected photon. Silicon photomultiplier (SiPM) based scintillation counters have a high detection efficiency, high electronic gain and compact dimensions. This makes them a very attractive candidate to replace routinely used detectors in many fields. More than 10 years ago the digital scanning radiography system based on multistrip ionization chamber (MIC) was suggested at Budker Institute of Nuclear Physics. The detector demonstrates excellent radiation resistance and parameter stability after 5 year operations and an imaging of up to 1000 persons per day. Currently, the installations operate at several Russian airports and at subway stations in some cities. At the present time we design a new detector operating in the photon counting mode, having superior parameters than the gas one, based on scintillator - SiPM assemblies. This detector has close to zero noise, higher quantum efficiency and a count rate capability of more than 5 MHz per channel (20% losses), which leads to better image quality and improved detection capability. The suggested detector technology could be expanded to medical applications.

  5. Application of digital radiography for measuring in clinical dental practice

    Directory of Open Access Journals (Sweden)

    Ilić Dragan V.

    2015-01-01

    Full Text Available Introduction. The recent literature data points out a rising application of digital radiography - radiovisiography (RVG - in dental clinical practice. Objective. The aim of this study was to apply and compare RVG with the conventional radiographic technique (CRDG in terms of accuracy in linear measurement in dentistry. Methods. Measurements were done on the mandibular dogs teeth considering incisors crown width and height of the surrounding alveolar bone using RVG and CRDG. The control technique (CONT involved values obtained by direct gauging in dogs mouth. Each measuring was done by two examiners. Results. Considering the incisors’ crown width, there were no significant statistical difference in measurement using CRDG, RVG and CONT technique (p>0.01. Concerning the alveolar height gauging there were no significant difference in recorded values between the two radiographic techniques (p>0.01. The high level of inter-examiner agreement was observed for scoring in all techniques (CRDG, RVG and CONT. Conclusion. Although RVG did not expose more accuracy comparing to CRDG, having opulent tool service the first technique contributed more comfortable work during measuring procedures in this study.

  6. Measuring and correcting wobble in large-scale transmission radiography

    CERN Document Server

    Rogers, Thomas W; Morton, Edward J; Griffin, Lewis D

    2016-01-01

    Large-scale transmission radiography scanners are used to image vehicles and cargo containers. Acquired images are inspected for threats by a human operator or a computer algorithm. To make accurate detections, it is important that image values are precise. However, due to the scale of such systems, they can be mechanically unstable, causing the imaging array to wobble during a scan. This leads to an effective loss of precision in the captured image. We consider the measurement of wobble and amelioration of the consequent loss of image precision. Following our previous work, we use Beam Position Detectors (BPDs) to measure the cross-sectional profile of the X-ray beam, allowing for estimation, and thus correction of wobble. We propose: (i) a model of image formation with a wobbling detector array; (ii) a method of wobble correction derived from this model; (iii) methods for calibrating sensor sensitivities and relative offsets; (iv) a Random Regression Forest based method for instantaneous estimation of detec...

  7. A conceptual optimisation strategy for radiography in a digital environment.

    Science.gov (United States)

    Båth, Magnus; Håkansson, Markus; Hansson, Jonny; Månsson, Lars Gunnar

    2005-01-01

    Using a completely digital environment for the entire imaging process leads to new possibilities for optimisation of radiography since many restrictions of screen/film systems, such as the small dynamic range and the lack of possibilities for image processing, do not apply any longer. However, at the same time these new possibilities lead to a more complicated optimisation process, since more freedom is given to alter parameters. This paper focuses on describing an optimisation strategy that concentrates on taking advantage of the conceptual differences between digital systems and screen/film systems. The strategy can be summarised as: (a) always include the anatomical background during the optimisation, (b) perform all comparisons at a constant effective dose and (c) separate the image display stage from the image collection stage. A three-step process is proposed where the optimal setting of the technique parameters is determined at first, followed by an optimisation of the image processing. In the final step the optimal dose level-given the optimal settings of the image collection and image display stages-is determined.

  8. Bacteriological research for the contamination of digital portable radiography

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Seong Gyu [Dept. of Radiology, Dong A University Hospital, Busan (Korea, Republic of); Lee, Hyo Yeong [Dept. of Radiological Science, Dong Eui University, Busan (Korea, Republic of)

    2017-03-15

    The study was performed to investigate the bacteriological contamination of portable digital radiography system and their detectors in a university hospital. CNS and VRE were detected in the samples collected from vinyl cover on detectors used for the infection control patients. On the other hand, no bacteria was detected in the samples collected from detectors with vinyl cover removed. In the series of imaging of patients from general wards, no bacteria was detected from the patient 1. However, CNS was detected from the patients 2 and 3, CNS and Enterococcus faecalis detected from the patient 4, CNS and Enterococcus casseliflavus detected from the patient 5, and CNS, Enterococcus casseliflavus, and Klebsiella pneumoniae all detected from the patient 6. CNS and Enterococcus faecium were detected in the controller handle of collimator. Also, CNS was detected from the handle of detector and exposure switch. In the treatment gloves of the radiological technologist after the imaging, CNS, Enterococcus gallinarum, and Klebsiella pneumoniae were detected. Therefore, it is recommended for DR portable to take images after sterilizing the detector after taking each image and to use disposable vinyl covers on detectors to remove after imaging. And treatment gloves must be changed after each imaging. Also, hospital infection via portables must be prevented by complete sterilization of the controller handles of collimator which are in frequent contact during imaging and infection education of employees.

  9. Location of mental foramen using digital panoramic radiography

    Directory of Open Access Journals (Sweden)

    Ajmal Mohamed

    2016-01-01

    Full Text Available Objective: Comparative evaluation of the location of mental foramen in different age groups. Determine the variation in position of mental foramen with gender using digital panoramic radiography. Materials and Methods: Digital panoramic radiographs of 250 patients were reviewed. The study population was divided into five age groups with 50 patients each. Radiographic position of mental foramen was evaluated in each radiograph based on three parameters. Measurements were taken in each radiograph using Planmeca Dimaxis pro version 4.4.0 (Helsinki, Finland. The collected data were subjected to statistical analysis using paired Student's t-test. Results: The mean distance of position of mental foramen showed a significant variation within the five age groups. In the first group, female patients showed an increase in mean distance of mental foramen position in relation to three parameters. From the second to fifth groups, male patient showed an increase in the mean distance of mental foramen position. The first and fifth group showed a reduced mean distance of mental foramen position when compared to other age groups. Conclusion: This study concluded that the position of mental foramen varies with age. There was a gender-related variation in position of mental foramen within the population too.

  10. Location of mental foramen using digital panoramic Radiography

    Science.gov (United States)

    Mohamed, Ajmal; Nataraj, Kannan; Mathew, Vinod B.; Varma, Beena; Mohamed, Shamil; Valappila, Nidhin J.; Meena, Aravind S.

    2016-01-01

    Objective: Comparative evaluation of the location of mental foramen in different age groups. Determine the variation in position of mental foramen with gender using digital panoramic radiography. Materials and Methods: Digital panoramic radiographs of 250 patients were reviewed. The study population was divided into five age groups with 50 patients each. Radiographic position of mental foramen was evaluated in each radiograph based on three parameters. Measurements were taken in each radiograph using Planmeca Dimaxis pro version 4.4.0 (Helsinki, Finland). The collected data were subjected to statistical analysis using paired Student's t-test. Results: The mean distance of position of mental foramen showed a significant variation within the five age groups. In the first group, female patients showed an increase in mean distance of mental foramen position in relation to three parameters. From the second to fifth groups, male patient showed an increase in the mean distance of mental foramen position. The first and fifth group showed a reduced mean distance of mental foramen position when compared to other age groups. Conclusion: This study concluded that the position of mental foramen varies with age. There was a gender-related variation in position of mental foramen within the population too. PMID:27555723

  11. Quantitative shadowgraphy and proton radiography for large intensity modulations

    Science.gov (United States)

    Kasim, Muhammad Firmansyah; Ceurvorst, Luke; Ratan, Naren; Sadler, James; Chen, Nicholas; Sävert, Alexander; Trines, Raoul; Bingham, Robert; Burrows, Philip N.; Kaluza, Malte C.; Norreys, Peter

    2017-02-01

    Shadowgraphy is a technique widely used to diagnose objects or systems in various fields in physics and engineering. In shadowgraphy, an optical beam is deflected by the object and then the intensity modulation is captured on a screen placed some distance away. However, retrieving quantitative information from the shadowgrams themselves is a challenging task because of the nonlinear nature of the process. Here, we present a method to retrieve quantitative information from shadowgrams, based on computational geometry. This process can also be applied to proton radiography for electric and magnetic field diagnosis in high-energy-density plasmas and has been benchmarked using a toroidal magnetic field as the object, among others. It is shown that the method can accurately retrieve quantitative parameters with error bars less than 10%, even when caustics are present. The method is also shown to be robust enough to process real experimental results with simple pre- and postprocessing techniques. This adds a powerful tool for research in various fields in engineering and physics for both techniques.

  12. Asymptomatic Intracranial Foreign Body: An Incidental Finding on Radiography

    Directory of Open Access Journals (Sweden)

    Maghsoudi

    2016-05-01

    Full Text Available Introduction Intracranial needles are rare entities. Intracranial foreign bodies due to non-missile intracranial penetrations are one of the most rarely encountered situations in neurosurgery. Sewing needles are among the more unusual foreign bodies that may be found in the brain. Although uncommon, foreign body cases are important and interesting. Foreign bodies enter the body through trauma or iatrogenic injuries. Needles are mostly inserted through fontanelles, cranial sutures, and more rarely through the orbits in infancy for the purpose of killing unwanted babies. Case Presentation This article presents a case of intracranial foreign body found upon radiography. A 24-year-old female, who two days prior to presentation suffered only once from dizziness, and was otherwise healthy. Conclusions Because this incident may have occurred during the patient’s neonatal period, it may be a case of child abuse. In spite of the very limited number of cases in the literature, having a stepmother, a stepfather, or a babysitter, being the youngest child, or having family members who suffer from psychiatric disorders, (especially if these relatives are responsible for child care, living in a society that allows homicide of children born from extramarital relationships, and being female have been suggested as possible risk factors.

  13. Atlantoaxial subluxation. Radiography and magnetic resonance imaging correlated to myelopathy

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, Y.; Takahashi, M.; Sakamoto, Y.; Kojima, R.

    Twenty-nine patients with atlantoaxial subluxation (18 with rheumatoid arthritis, 2 due to trauma, 4 with os odontoideum, and one each with polyarteritis nodosa, rheumatic fever, Klippel-Feil syndrome, achondroplasia, and cause unknown) were evaluated using a 0.22 tesla resistive MRI unit. Cord compression was classified into four grades according to the degree on magnetic resonance imaging. There were 7 patients with no thecal sac compression (grade 0), 10 with a minimal degree of subarachnoid space compression without cord compression (grade 1), 7 with mild cord compression (grade 2), and 5 with severe cord compression or cord atrophy (grade 3). Although the severity of myelopathy showed poor correlation with the atlantodental interval on conventional radiography, high correlation was observed between MR grading and the degree of myelopathy. The high signal intensity foci were observed in 7 or 12 patients with cord compression (grades 2 and 3) on T2 weighted images. Other frequently observed findings in rheumatoid arthritis included soft tissue masses of low to intermediate signal intensity in the paraodontoid space, erosions of the odontoid processes, and atlanto-axial impaction on T1 and T2 weighted images.

  14. Digital Radiography and Computed Tomography (DRCT) Product Improvement Plan (PIP)

    Energy Technology Data Exchange (ETDEWEB)

    Tim Roney; Bob Pink; Karen Wendt; Robert Seifert; Mike Smith

    2010-12-01

    The Idaho National Laboratory (INL) has been developing and deploying x-ray inspection systems for chemical weapons containers for the past 12 years under the direction of the Project Manager for Non-Stockpile Chemical Materiel (PMNSCM). In FY-10 funding was provided to advance the capabilities of these systems through the DRCT (Digital Radiography and Computed Tomography) Product Improvement Plan (PIP), funded by the PMNSCM. The DRCT PIP identified three research tasks; end user study, detector evaluation and DRCT/PINS integration. Work commenced in February, 2010. Due to the late start and the schedule for field inspection of munitions at various sites, it was not possible to spend sufficient field time with operators to develop a complete end user study. We were able to interact with several operators, principally Mr. Mike Rowan who provided substantial useful input through several discussions and development of a set of field notes from the Pueblo, CO field mission. We will be pursuing ongoing interactions with field personnel as opportunities arise in FY-11.

  15. Micro-radiography of biological samples with medical contrast agents

    Energy Technology Data Exchange (ETDEWEB)

    Dammer, J., E-mail: jiri.dammer@lf1.cuni.cz [Charles University in Prague, First Faculty of Medicine, Salmovská 1, 120 00 Prague 2 (Czech Republic); Hospital Na Bulovce, Department of Radiological Physics, Budinova 2, 180 81 Prague 8 (Czech Republic); Institute of Experimental and Applied Physics, Czech Technical University in Prague, Horska 3a/22, 128 00 Prague 2 (Czech Republic); Weyda, F. [Faculty of Science, University of South Bohemia, Branisovska 31, 370 05 Ceske Budejovice (Czech Republic); Benes, J. [Charles University in Prague, First Faculty of Medicine, Salmovská 1, 120 00 Prague 2 (Czech Republic); Sopko, V. [Hospital Na Bulovce, Department of Radiological Physics, Budinova 2, 180 81 Prague 8 (Czech Republic); Institute of Experimental and Applied Physics, Czech Technical University in Prague, Horska 3a/22, 128 00 Prague 2 (Czech Republic); Gelbic, I. [Biology Centre, AS CR, Institute of Entomology, Department of Biochemistry and Physiology, Branisovska 31, CZ-37005 Ceske Budejovice (Czech Republic)

    2013-12-01

    Micro-radiography is an imaging technique that uses X-rays to study the internal structures of objects. This fast and easy imaging tool is based on differential X-ray attenuation by various tissues and structures within biological samples. The experimental setup described is based on the semiconductor pixel X-ray detector Medipix2 and X-ray micro-focus tube. Our micro-radiographic system has been recently used not only for the examination of internal structures of various arthropods and other biological objects but also for tracing some processes in selected model species (we used living larvae of mosquito Culex quinquefasciatus). Low concentrations of iodine, lanthanum or gold particles were used as a tracer (contrast agent). Such contrast agents increase the absorption of X-rays and allow a better visibility of internal structures of model organisms (especially the various cavities, pores, etc.). In addition, the movement of tracers in selected timing experiments demonstrates some physiological functions of digestive and excretory system.

  16. The new neutron radiography/tomography/imaging station DINGO at OPAL

    Energy Technology Data Exchange (ETDEWEB)

    Garbe, U., E-mail: ulf.garbe@ansto.gov.au [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW 2234 (Australia); Randall, T.; Hughes, C. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW 2234 (Australia)

    2011-09-21

    A new neutron imaging instrument will be built to support the area of neutron imaging research (neutron radiography/tomography) at ANSTO. The instrument will be designed for an international user community and for routine quality control for defence, industrial, mining, space and aircraft applications. It will also be a useful tool for assessing oil and water flow in sedimentary rock reservoirs (like the North West Shelf), assessing water damage in aircraft components, and the study of hydrogen distribution and cracking in steel. The instrument is planned to be completed by the end of June 2013 and is currently in the design stage. The usable neutron flux is mainly determined by the neutron source, but it also depends on the instrument position and the resolution. The designated instrument position for DINGO is the beam port HB-2 in the reactor hall. The estimated flux for an L/D of approximately 250 at HB-2 is calculated by Mcstas simulation in a range of 4.75x10{sup 7} n/cm{sup 2} s, which is in the same range of other facilities like ANSTARES (FRM II; Schillinger et al., 2004 ) or BT2 (NIST; Hussey et al., 2005 ). A special feature of DINGO is the in-pile collimator place in front of the main shutter at HB-2. The collimator offers two pinholes with a possible L/D of 250 and 1000. A secondary collimator will separate the two beams and block one. The whole instrument will operate in two different positions, one for high resolution and the other for high speed.

  17. The new neutron radiography/tomography/imaging station DINGO at OPAL

    Science.gov (United States)

    Garbe, U.; Randall, T.; Hughes, C.

    2011-09-01

    A new neutron imaging instrument will be built to support the area of neutron imaging research (neutron radiography/tomography) at ANSTO. The instrument will be designed for an international user community and for routine quality control for defence, industrial, mining, space and aircraft applications. It will also be a useful tool for assessing oil and water flow in sedimentary rock reservoirs (like the North West Shelf), assessing water damage in aircraft components, and the study of hydrogen distribution and cracking in steel. The instrument is planned to be completed by the end of June 2013 and is currently in the design stage. The usable neutron flux is mainly determined by the neutron source, but it also depends on the instrument position and the resolution. The designated instrument position for DINGO is the beam port HB-2 in the reactor hall. The estimated flux for an L/ D of approximately 250 at HB-2 is calculated by Mcstas simulation in a range of 4.75×10 7 n/cm 2 s, which is in the same range of other facilities like ANSTARES (FRM II; Schillinger et al., 2004 [1]) or BT2 (NIST; Hussey et al., 2005 [2]). A special feature of DINGO is the in-pile collimator place in front of the main shutter at HB-2. The collimator offers two pinholes with a possible L/ D of 250 and 1000. A secondary collimator will separate the two beams and block one. The whole instrument will operate in two different positions, one for high resolution and the other for high speed.

  18. Carolinas Energy Career Center

    Energy Technology Data Exchange (ETDEWEB)

    Classens, Anver; Hooper, Dick; Johnson, Bruce

    2013-03-31

    Central Piedmont Community College (CPCC), located in Charlotte, North Carolina, established the Carolinas Energy Career Center (Center) - a comprehensive training entity to meet the dynamic needs of the Charlotte region's energy workforce. The Center provides training for high-demand careers in both conventional energy (fossil) and renewable energy (nuclear and solar technologies/energy efficiency). CPCC completed four tasks that will position the Center as a leading resource for energy career training in the Southeast: • Development and Pilot of a New Advanced Welding Curriculum, • Program Enhancement of Non-Destructive Examination (NDE) Technology, • Student Support through implementation of a model targeted toward Energy and STEM Careers to support student learning, • Project Management and Reporting. As a result of DOE funding support, CPCC achieved the following outcomes: • Increased capacity to serve and train students in emerging energy industry careers; • Developed new courses and curricula to support emerging energy industry careers; • Established new training/laboratory resources; • Generated a pool of highly qualified, technically skilled workers to support the growing energy industry sector.

  19. Research and Application of Dynamic Reliability Centered Maintenance for Process Industry%过程工业动态的以可靠性为中心的维修研究及应用

    Institute of Scientific and Technical Information of China (English)

    王庆锋; 高金吉

    2012-01-01

    针对过程工业设备类型、结构、运行和维护特点,研究过程工业以可靠性为中心的维修评估技术,开发集风险评估、状态监测、绩效审查、专业管理、档案管理为一体的动态的以可靠性为中心的维修决策系统.利用风险评估技术确定设备优先维护等级、优化维修内容、确定最佳维修时间指导设备维护和维修决策;状态监测用于故障诊断与预测确定设备预知性维修任务;绩效指标用于量化关键部件故障频率和故障后果,确定关键部件的最佳维修周期进而量化设备动态风险、确定预防性维修任务内容;专业管理是维修决策和维修内容的执行环节.开发的系统应用于中国石油某炼油厂,实现以信息为重要资源,以设备健康状态为依据,基于风险量化指标决策和设备量化风险动态管理,提高维修决策水平,确保了设备运行的安全性、可靠性和可用性.%According to the type, structure, operating and maintenance characteristic difference of process industry equipment, the evaluation technology of Reliability Centered Maintenance for Process Industry is studied. A kind of dynamic Reliability Centered Maintenance decision-making system which integrated risk evaluation, condition monitoring, performance check, professional management, archive management together is developed, which is based on information as main resources and health condition monitoring as the decision-making basis. Risk assessment technology is applied to form maintenance decision-making, such as to determine the priority maintenance level, to optimize maintenance content, and to determine the right maintenance time. Condition monitoring serves as a tool to diagnosis equipment fault and to predict fault development, and used to determine prediction maintenance tasks. Performance indicators used to quantify the frequency and fault consequences of key parts fault, to determine the optimal

  20. Accuracy of Digital Bitewing Radiography versus Different Views of Digital Panoramic Radiography for Detection of Proximal Caries

    Science.gov (United States)

    Abdinian, Mehrdad; Razavi, Sayed Mohammad; Samety, Amir Abbas; Faghihian, Elham

    2015-01-01

    Objectives: Dental caries are common and have a high incidence among populations. Radiographs are essential for detecting proximal caries. The best technique should be recognized for accurate detection of caries. The aim of this study was to compare the accuracy of detection of proximal caries using intraoral bitewing, extraoral bitewing, improved interproximal panoramic, improved orthogonality panoramic and conventional panoramic radiographs. Materials and Methods: In this descriptive cross sectional study, 100 extracted human teeth with and without proximal caries were used. Intra and extraoral radiographs were taken. Images were evaluated and scored by two observers. Scores were compared with the histological gold standard. The diagnostic accuracy of radiographs was assessed by means of receiver operating characteristic (ROC) curve analysis (P<0.05). Results: Microscopic evaluation of proximal surfaces revealed that 54.8% of the surfaces were sound and 45.2% were carious (with different depths). The differences in the area under the ROC curve (Az value) among the five techniques were not statistically significant. Conclusion: Improved interproximal panoramic and extraoral bitewing radiographs were superior to conventional panoramic radiography for detection of proximal caries ex vivo and should be considered for patients with contraindications for intraoral radiographs. PMID:26622284