Formation and growth of embedded indium nanoclusters by In2+ implantation in silica

International Nuclear Information System (INIS)

Santhana Raman, P.; Nair, K.G.M.; Kesavamoorthy, R.; Panigrahi, B.K.; Dhara, S.; Ravichandran, V.

2007-01-01

Indium nanoclusters are synthesized in an amorphous silica matrix using an ion-implantation technique. Indium ions (In 2+ ) with energy of 890 keV are implanted on silica to fluences in the range of 3 x 10 16 -3 x 10 17 cm -2 . The formation of indium nanoclusters is confirmed by optical absorption spectrometry and glancing incidence X-ray diffraction studies. A low frequency Raman scattering technique is used to study the growth of embedded indium nanoclusters in the silica matrix as a function of fluence and post-implantation annealing duration. Rutherford backscattering spectrometry studies show the surface segregation of implanted indium. Photoluminescence studies indicate the formation of a small quantity of indium oxide phase in the ion-implanted samples. (orig.)

Implant damage and redistribution of indium in indium-implanted thin silicon-on-insulator

International Nuclear Information System (INIS)

Chen Peng; An Zhenghua; Zhu Ming; Fu, Ricky K.Y.; Chu, Paul K.; Montgomery, Neil; Biswas, Sukanta

2004-01-01

The indium implant damage and diffusion behavior in thin silicon-on-insulator (SOI) with a 200 nm top silicon layer were studied for different implantation energies and doses. Rutherford backscattering spectrometry in the channeling mode (RBS/C) was used to characterize the implant damage before and after annealing. Secondary ion mass spectrometry (SIMS) was used to study the indium transient enhanced diffusion (TED) behavior in the top Si layer of the SOI structure. An anomalous redistribution of indium after relatively high energy (200 keV) and dose (1 x 10 14 cm -2 ) implantation was observed in both bulk Si and SOI substrates. However, there exist differences in these two substrates that are attributable to the more predominant out-diffusion of indium as well as the influence of the buried oxide layer in the SOI structure

Investigation into chemism of multivalent element ions reactions with organic reagents. XXXII. Extractable indium complex with alizarin-3-sulfonic acid and diphenylguanidine

Energy Technology Data Exchange (ETDEWEB)

Biryuk, E A; Nazarenko, V A [AN Ukrainskoj SSR, Kiev. Inst. Obshchej i Neorganicheskoj Khimii; AN Ukrainskoj SSR, Odessa. Inst. Obshchej i Neorganicheskoj Khimii)

1975-09-01

Spectrophotometric investigations have been made in to the interaction of indium with alizarin red S (alizarin-3-sulphonic acid) when extracting it with chloroform. The complex is extracted as an ion association with diphenylguanidine, in which the ratio In:Aliz:DPG = 1:3:3. The central ion In/sup 3 +/ substitutes three protons in three particles of the ligand. The structure of the complex being extracted is discussed. Molar absorbancy index of the complex in the chloroform extract (2.8x10/sup 4/) is twice as great as in the aqueous solution. The effect of the pH value on the formation of the indium complexes extracted is studied.

Deposition of indium tin oxide thin films by cathodic arc ion plating

International Nuclear Information System (INIS)

Yang, M.-H.; Wen, J.-C.; Chen, K.-L.; Chen, S.-Y.; Leu, M.-S.

2005-01-01

Indium tin oxide (ITO) thin films have been deposited by cathodic arc ion plating (CAIP) using sintered oxide target as the source material. In an oxygen atmosphere of 200 deg. C, ITO films with a lowest resistivity of 2.2x10 -4 Ω-cm were obtained at a deposition rate higher than 450 nm/min. The carrier mobility of ITO shows a maximum at some medium pressures. Although morphologically ITO films with a very fine nanometer-sized structure were observed to possess the lowest resistivity, more detailed analyses based on X-ray diffraction are attempted to gain more insight into the factors that govern electron mobility in this investigation

Processing of indium (III solutions via ion exchange with Lewatit K-2621 resin

Directory of Open Access Journals (Sweden)

López Díaz-Pavón, Adrián

2014-06-01

Full Text Available The processing of indium(III-hydrochloric acid solutions by the cationic ion exchange Lewatit K-2621 resin has been investigated. The influence of several variables such as the hydrochloric acid and metal concentrations in the aqueous solution and the variation of the amount of resin added has been studied. Moreover, a kinetic study performed in the uptake of indium(III by Lewatit K-2621, shows that either the film-diffusion and the particle-diffusion models fit the ion exchange process onto the resin, depending upon the initial metal concentration in the aqueous solution. The loaded resin could be eluted by HCl solutions at 20 °C.Se ha investigado el tratamiento de disoluciones de ácido clorhídrico conteniendo indio(III mediante la resina de cambio catiónico Lewatit K-2621. Las variables ensayadas han sido las concentraciones de ácido y de metal en la disolución acuosa y la cantidad de resina empleada en el tratamiento de dichas disoluciones. Asimismo, se ha llevado a cabo un estudio cinético del proceso de intercambio catiónico entre el indio(III y la resina Lewatit K-2621. Este estudio muestra que el proceso de intercambio responde a un mecanismo de difusión en la disolución o en la partícula de resina dependiendo de la concentración inicial del metal en el medio acuoso. El metal cargado en la resina puede ser eluido con disoluciones de ácido clorhídrico a 20 °C.

Effect of ion indium implantation on InP photoluminescence spectra

International Nuclear Information System (INIS)

Pyshnaya, N.B.; Radautsan, S.I.; Tiginyanu, I.M.; Ursaki, V.V.

1988-01-01

Photoluminescence spectra of indium phosphide single crystals implanted by indium after annealing under the protective Al 2 O 3 film in a nitrogen flow are investigated. As a result of implantation and annealing in photoluminescence spectra of crystals there appeared a new band with the maximum at 1.305 eV (T=6 K) which is connected with the free electron transition at the level of the antistructure defect of In p - lying by 0.115 eV above the valent zone ceiling. With large doses of the implanted indium in the photoluminescence spectrum a long-wave band with the maximum at 0.98-0.99 eV is also observed caused, apparently, by the strong lattice disorder

Indium sulfide precipitation from hydrochloric acid solutions of calcium and sodium chlorides

International Nuclear Information System (INIS)

Kochetkova, N.V.; Bayandina, Yu.E.; Toptygina, G.M.; Shepot'ko, A.O.

1988-01-01

The effect of precipitation duration, acid concentration, indium complexing with chloride ions on the process of indium sulfide chemical precipitation in hydrochloric acid solutions, precipitate composition and dispersity are studied. It is established that indium sulfide solubility increases in solutions with acid concentration exceeding 0.40-0.45 mol/l. Calcium and indium chloride addition to diluted hydrochloric solutions greatly increases the solubility of indium sulfide. The effect of calcium chloride on In 2 S 3 solubility is higher than that of sodium chloride

Voltammetry and coulometry of indium in two-side thin-layer system

International Nuclear Information System (INIS)

Eliseeva, L.V.; Kabanova, O.L.

1980-01-01

An electrochemical behaviour of In and possibilities for its determination have been investigated, using halide background solutions, by voltametry in the thin solution layer thin mercury film system. It has been shown that the maximum current of indium (3) is directly proportional to its concentration over a range of 1x10 -4 - 5x10 -3 M and the maximum current of indium oxidation from the amalgam over a range of 5x10 -7 - 1x10 -4 M. Examined were the effects of halide ion concentration, pH, electrode potential change rate on current maximum value, product efficiency of reducing indium (3) and oxidizing its amalgam, on maximum current potential and half-peak width. The analytical signal has been found to be directly proportional to chloride ion concentration over a range of 0.1 - 3.0 M, bromide and iodide ion concentration over a range of 0.1 - 1.0 M. This makes it possible to use the method for determination of halide ions

The effect of annealing ambient on surface segregation in indium implanted sapphire

International Nuclear Information System (INIS)

Sood, D.K.; Victoria University of Technology, Melbourne; Zhou, W.; Victoria University of Technology, Melbourne; Academia Sinica, Shanghai Institute of Metallurgy; Cao, D.X.; Victoria University of Technology, Melbourne; Academia Sinica, Shanghai, SH

1991-01-01

A systematic study of the effect of annealing ambient on both indium surface segregation and lattice damage recovery of single crystal Al 2 O 3 has been done by performing 1 hour anneals at 800 deg C for the samples identically implanted with indium ions at 100keV energy to a high dose of 5x10 16 ions/cm 2 . Following solid phase epitaxial re-crystallization of amorphous layer, the indium dopant shows rapid thermal migration. The indium redistribution consists of 2 parts: 1. appreciable broadening corresponding to diffusion within the amorphous layer, and 2. indium segregation to the free surface to form In 2 O 3 , or escape out of the surface to sublime into the surrounding ambient. Lattice damage recovery depends on indium concentration profile in amorphous layer of Al 2 O 3 which is directly influenced by the annealing ambient. It is confirmed that the presence of moisture or oxygen in annealing ambient results in In 2 O 3 formation on the surface. (author). 6 refs.; 3 figs.; 1 tab

Selective separation of indium by iminodiacetic acid chelating resin

International Nuclear Information System (INIS)

Fortes, M.C.B.; Benedetto, J.S.; Martins, A.H.

2007-01-01

- Indium can be recovered by treating residues, flue dusts, slags, and metallic intermediates in zinc smelting. This paper investigates the adsorption characteristics of indium and iron on an iminodiacetic acid chelating resin, Amberlite R IRC748 (Rohm and Haas Co.-USA). High concentrations of iron are always present in the aqueous feed solution of indium recovery. In addition, the chemical behaviour of iron in adsorptive systems is similar to that of indium. The metal concentrations in the aqueous solution were based on typical indium sulfate leach liquor obtained from zinc hydrometallurgical processing in a Brazilian plant. The ionic adsorption experiments were carried out by the continuous column method. Amberlite R IRC748 resin had a high affinity for indium under acidic conditions. Indium ions adsorbed onto the polymeric resin were eluted with a 0.5 mol/dm 3 sulphuric acid solution passed through the resin bed in the column. 99.5% pure indium sulfate aqueous solution was obtained using the iminodiacetic acid chelating resin Amberlite R IRC748. (author)

Indium-tin-oxide thin film deposited by a dual ion beam assisted e-beam evaporation system

International Nuclear Information System (INIS)

Bae, J.W.; Kim, J.S.; Yeom, G.Y.

2001-01-01

Indium-tin-oxide (ITO) thin films were deposited on polycarbonate (PC) substrates at low temperatures (<90 deg. C) by a dual ion beam assisted e-beam evaporation system, where one gun (gun 1) is facing ITO flux and the other gun (gun 2) is facing the substrate. In this experiment, effects of rf power and oxygen flow rate of ion gun 2 on the electrical and optical properties of depositing ITO thin films were investigated. At optimal deposition conditions, ITO thin films deposited on the PC substrates larger than 20 cmx20 cm showed the sheet resistance of less than 40 Ω/sq., the optical transmittance of above 90%, and the uniformity of about 5%

Solvent extraction of anionic chelate complexes of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) with 2-thenoyltrifluoroacetone as ion-pairs with tetrabutylammonium ions

International Nuclear Information System (INIS)

Noro, Junji; Sekine, Tatsuya.

1992-01-01

The solvent extraction of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) in 0.1 mol dm -3 sodium nitrate solutions with 2-thenoyltrifluoroacetone (Htta) in the absence and presence of tetrabutylammonium ions (tba + ) into carbon tetrachloride was measured. The extraction of lanthanum(III), europium(III), and lutetium(III) was greatly enhanced by the addition of tba + ; this could be explained in terms of the extraction of a ternary complex, M(tta) 4 - tba + . However, the extractions of scandium(III) and indium(III) were nearly the same when tba + was added. The data were treated on the basis of the formation equilibrium of the ternary complex from the neutral chelate, M(tta) 3 , with the extracted ion-pairs of the reagents, tta - tba + , in the organic phase. It was concluded that the degree of association of M(tta) 3 with the ion-pair, tta - tba + , is greater in the order La(tta) 3 ≅ Eu(tta) 3 > Lu(tta) 3 , or that the stability of the ternary complex in the organic phase is higher in the order La(tta) 4 - tba + ≅ Eu(tta) 4 - tba + > Lu(tta) 4 - tba + . This is similar to those of adduct metal chelates of Htta with tributylphosphate (TBP) in synergistic extraction systems. (author)

A Solid-Contact Indium(III) Sensor based on a Thiosulfinate Ionophore Derived from Omeprazole

Energy Technology Data Exchange (ETDEWEB)

Abbas, Mohammad Nooredeen; Hend Samy Amer [National Research Centre, Cairo (Egypt)

2013-04-15

A novel solid-contact indium(III)-selective sensor based on bis-(1H-benzimidazole-5-methoxy-2-[(4-methoxy-3, 5-dimethyl-1-pyridinyl) 2-methyl]) thiosulfinate, known as an omeprazole dimer (OD) and a neutral ionophore, was constructed, and its performance characteristics were evaluated. The sensor was prepared by applying a membrane cocktail containing the ionophore to a graphite rod pre-coated with polyethylene dioxythiophene (PEDOT) conducting polymer as the ion-to-electron transducer. The membrane contained 3.6% OD, 2.3% oleic acid (OA) and 62% dioctyl phthalate (DOP) as the solvent mediator in PVC and produced a good potentiometric response to indium(III) ions with a Nernstian slope of 19.09 mV/decade. The constructed sensor possessed a linear concentration range from 3 Χ 10{sup -7} to 1 Χ 10{sup -2} M and a lower detection limit (LDL) of 1 Χ 10{sup -7} M indium(III) over a pH range of 4.0-7.0. It also displayed a fast response time and good selectivity for indium(III) over several other ions. The sensor can be used for longer than three months without any considerable divergence in potential. The sensor was utilized for direct and flow injection potentiometric (FIP) determination of indium(III) in alloys. The parameters that control the flow injection method were optimized. Indium(III) was quantitatively recovered, and the results agreed with those obtained using atomic absorption spectrophotometry, as confirmed by the f and t values. The sensor was also utilized as an indicator electrode for the potentiometric titration of fluoride in the presence of chloride, bromide, iodide and thiocyanate ions using indium(III) nitrate as the titrant.

Copper-assisted shape control in colloidal synthesis of indium oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Selishcheva, Elena; Parisi, Juergen; Kolny-Olesiak, Joanna, E-mail: joanna.kolny@uni-oldenburg.de [University of Oldenburg, Energy and Semiconductor Research Laboratory, Institute of Physics (Germany)

2012-02-15

Indium oxide is an important n-type transparent semiconductor, finding application in solar cells, sensors, and optoelectronic devices. We present here a novel non-injection synthesis route for the preparation of colloidal indium oxide nanocrystals by using oleylamine (OLA) as ligand and as solvent. Indium oxide with cubic crystallographic structure is formed in a reaction between indium acetate and OLA, the latter is converted to oleylamide during the synthesis. The shape of the nanocrystals can be influenced by the addition of copper ions. When only indium (III) acetate is used as precursor flower-shaped indium oxide nanoparticles are obtained. Addition of copper salts such as copper (I) acetate, copper (II) acetate, copper (II) acetylacetonate, or copper (I) chloride, under otherwise identical reaction conditions changes the shape of nanoparticles to quasi-spherical or elongated. The anions, except for chloride, do not influence the shape of the resulting nanocrystals. This finding suggests that adsorption of copper ions on the In{sub 2}O{sub 3} surface during the nanoparticles growth is responsible for shape control, whereas changes in the reactivity of the In cations caused by the presence of different anions play a secondary role. X-ray diffraction, transmission electron microscopy, nuclear magnetic resonance, energy dispersive X-ray analysis, and UV-Vis-absorption spectroscopy are used to characterize the samples.

Copper-assisted shape control in colloidal synthesis of indium oxide nanoparticles

International Nuclear Information System (INIS)

Selishcheva, Elena; Parisi, Jürgen; Kolny-Olesiak, Joanna

2012-01-01

Indium oxide is an important n-type transparent semiconductor, finding application in solar cells, sensors, and optoelectronic devices. We present here a novel non-injection synthesis route for the preparation of colloidal indium oxide nanocrystals by using oleylamine (OLA) as ligand and as solvent. Indium oxide with cubic crystallographic structure is formed in a reaction between indium acetate and OLA, the latter is converted to oleylamide during the synthesis. The shape of the nanocrystals can be influenced by the addition of copper ions. When only indium (III) acetate is used as precursor flower-shaped indium oxide nanoparticles are obtained. Addition of copper salts such as copper (I) acetate, copper (II) acetate, copper (II) acetylacetonate, or copper (I) chloride, under otherwise identical reaction conditions changes the shape of nanoparticles to quasi-spherical or elongated. The anions, except for chloride, do not influence the shape of the resulting nanocrystals. This finding suggests that adsorption of copper ions on the In 2 O 3 surface during the nanoparticles growth is responsible for shape control, whereas changes in the reactivity of the In cations caused by the presence of different anions play a secondary role. X-ray diffraction, transmission electron microscopy, nuclear magnetic resonance, energy dispersive X-ray analysis, and UV–Vis-absorption spectroscopy are used to characterize the samples.

Thin film metrology and microwave loss characterization of indium and aluminum/indium superconducting planar resonators

Science.gov (United States)

McRae, C. R. H.; Béjanin, J. H.; Earnest, C. T.; McConkey, T. G.; Rinehart, J. R.; Deimert, C.; Thomas, J. P.; Wasilewski, Z. R.; Mariantoni, M.

2018-05-01

Scalable architectures characterized by quantum bits (qubits) with low error rates are essential to the development of a practical quantum computer. In the superconducting quantum computing implementation, understanding and minimizing material losses are crucial to the improvement of qubit performance. A new material that has recently received particular attention is indium, a low-temperature superconductor that can be used to bond pairs of chips containing standard aluminum-based qubit circuitry. In this work, we characterize microwave loss in indium and aluminum/indium thin films on silicon substrates by measuring superconducting coplanar waveguide resonators and estimating the main loss parameters at powers down to the sub-photon regime and at temperatures between 10 and 450 mK. We compare films deposited by thermal evaporation, sputtering, and molecular beam epitaxy. We study the effects of heating in a vacuum and ambient atmospheric pressure as well as the effects of pre-deposition wafer cleaning using hydrofluoric acid. The microwave measurements are supported by thin film metrology including secondary-ion mass spectrometry. For thermally evaporated and sputtered films, we find that two-level state are the dominant loss mechanism at low photon number and temperature, with a loss tangent due to native indium oxide of ˜ 5 × 10 - 5 . The molecular beam epitaxial films show evidence of the formation of a substantial indium-silicon eutectic layer, which leads to a drastic degradation in resonator performance.

Quantitative evaluation of high-energy O- ion particle flux in a DC magnetron sputter plasma with an indium-tin-oxide target

Science.gov (United States)

Suyama, Taku; Bae, Hansin; Setaka, Kenta; Ogawa, Hayato; Fukuoka, Yushi; Suzuki, Haruka; Toyoda, Hirotaka

2017-11-01

O- ion flux from the indium tin oxide (ITO) sputter target under Ar ion bombardment is quantitatively evaluated using a calorimetry method. Using a mass spectrometer with an energy analyzer, O- energy distribution is measured with spatial dependence. Directional high-energy O- ion ejected from the target surface is observed. Using a calorimetry method, localized heat flux originated from high-energy O- ion is measured. From absolute evaluation of the heat flux from O- ion, O- particle flux in order of 1018 m-2 s-1 is evaluated at a distance of 10 cm from the target. Production yield of O- ion on the ITO target by one Ar+ ion impingement at a kinetic energy of 244 eV is estimated to be 3.3  ×  10-3 as the minimum value.

Quantitative evaluation of high-energy O− ion particle flux in a DC magnetron sputter plasma with an indium-tin-oxide target

International Nuclear Information System (INIS)

Suyama, Taku; Bae, Hansin; Setaka, Kenta; Ogawa, Hayato; Fukuoka, Yushi; Suzuki, Haruka; Toyoda, Hirotaka

2017-01-01

O − ion flux from the indium tin oxide (ITO) sputter target under Ar ion bombardment is quantitatively evaluated using a calorimetry method. Using a mass spectrometer with an energy analyzer, O − energy distribution is measured with spatial dependence. Directional high-energy O − ion ejected from the target surface is observed. Using a calorimetry method, localized heat flux originated from high-energy O − ion is measured. From absolute evaluation of the heat flux from O − ion, O − particle flux in order of 10 18 m −2 s −1 is evaluated at a distance of 10 cm from the target. Production yield of O − ion on the ITO target by one Ar + ion impingement at a kinetic energy of 244 eV is estimated to be 3.3  ×  10 −3 as the minimum value. (paper)

Surface modification of indium tin oxide films by amino ion implantation for the attachment of multi-wall carbon nanotubes

International Nuclear Information System (INIS)

Jiao Jiao; Liu Chenyao; Chen Qunxia; Li Shuoqi; Hu Jingbo; Li Qilong

2010-01-01

Amino ion implantation was carried out at the energy of 80 keV with fluence of 5 x 10 15 ions cm -2 for indium tin oxide film (ITO) coated glass, and the existence of amino group on the ITO surface was verified by X-ray photoelectron spectroscopy analysis and Fourier transform infrared spectra. Scanning electron microscopy images show that multi-wall carbon nanotubes (MWCNTs) directly attached to the amino ion implanted ITO (NH 2 /ITO) surface homogeneously and stably. The resulting MWCNTs-attached NH 2 /ITO (MWCNTs/NH 2 /ITO) substrate can be used as electrode material. Cyclic voltammetry results indicate that the MWCNTs/NH 2 /ITO electrode shows excellent electrochemical properties and obvious electrocatalytic activity towards uric acid, thus this material is expected to have potential in electrochemical analysis and biosensors.

Precursors for formation of copper selenide, indium selenide, copper indium diselenide, and/or copper indium gallium diselenide films

Science.gov (United States)

Curtis, Calvin J; Miedaner, Alexander; Van Hest, Maikel; Ginley, David S

2014-11-04

Liquid-based precursors for formation of Copper Selenide, Indium Selenide, Copper Indium Diselenide, and/or copper Indium Galium Diselenide include copper-organoselenides, particulate copper selenide suspensions, copper selenide ethylene diamine in liquid solvent, nanoparticulate indium selenide suspensions, and indium selenide ethylene diamine coordination compounds in solvent. These liquid-based precursors can be deposited in liquid form onto substrates and treated by rapid thermal processing to form crystalline copper selenide and indium selenide films.

Formation of copper-indium-selenide and/or copper-indium-gallium-selenide films from indium selenide and copper selenide precursors

Science.gov (United States)

Curtis, Calvin J [Lakewood, CO; Miedaner, Alexander [Boulder, CO; Van Hest, Maikel [Lakewood, CO; Ginley, David S [Evergreen, CO; Nekuda, Jennifer A [Lakewood, CO

2011-11-15

Liquid-based indium selenide and copper selenide precursors, including copper-organoselenides, particulate copper selenide suspensions, copper selenide ethylene diamine in liquid solvent, nanoparticulate indium selenide suspensions, and indium selenide ethylene diamine coordination compounds in solvent, are used to form crystalline copper-indium-selenide, and/or copper indium gallium selenide films (66) on substrates (52).

A review of the world market of indium (Economy of indium)

International Nuclear Information System (INIS)

Naumov, A.V.

2005-01-01

A review of the current state of the world and Russian markets of indium and indium-containing products was made based on the publications of the last years. Main fields of indium application are given, in particular, its using for neutron absorbing regulating rods in nuclear reactors. The second γ-radiation resulted from neutron absorption allows using indium as a neutron detector. Indium market stabilization is expected due to supply from China and South Korea [ru

Different magnetic properties of rhombohedral and cubic Ni2+ doped indium oxide nanomaterials

Directory of Open Access Journals (Sweden)

Qingbo Sun

2011-12-01

Full Text Available Transition metal ions doped indium oxide nanomaterials were potentially used as a kind of diluted magnetic semiconductors in transparent spintronic devices. In this paper, the influences of Ni2+ doped contents and rhombohedral or cubic crystalline structures of indium oxide on magnetic properties were investigated. We found that the magnetic properties of Ni2+ doped indium oxide could be transferred from room temperature ferromagnetisms to paramagnetic properties with increments of doped contents. Moreover, the different crystalline structures of indium oxide also greatly affected the room temperature ferromagnetisms due to different lattice constants and almost had no effects on their paramagnetic properties. In addition, both the ferromagnetic and paramagnetic properties were demonstrated to be intrinsic and not caused by impurities.

Sputtering yields and surface chemical modification of tin-doped indium oxide in hydrocarbon-based plasma etching

Energy Technology Data Exchange (ETDEWEB)

Li, Hu; Karahashi, Kazuhiro; Hamaguchi, Satoshi, E-mail: hamaguch@ppl.eng.osaka-u.ac.jp [Center for Atomic and Molecular Technologies, Osaka University, Yamadaoka 2-1, Suita 565-0871 (Japan); Fukasawa, Masanaga; Nagahata, Kazunori; Tatsumi, Tetsuya [Device and Material R& D Group, RDS Platform, Sony Corporation, Kanagawa 243-0014 (Japan)

2015-11-15

Sputtering yields and surface chemical compositions of tin-doped indium oxide (or indium tin oxide, ITO) by CH{sup +}, CH{sub 3}{sup +}, and inert-gas ion (He{sup +}, Ne{sup +}, and Ar{sup +}) incidence have been obtained experimentally with the use of a mass-selected ion beam system and in-situ x-ray photoelectron spectroscopy. It has been found that etching of ITO is chemically enhanced by energetic incidence of hydrocarbon (CH{sub x}{sup +}) ions. At high incident energy incidence, it appears that carbon of incident ions predominantly reduce indium (In) of ITO and the ITO sputtering yields by CH{sup +} and CH{sub 3}{sup +} ions are found to be essentially equal. At lower incident energy (less than 500 eV or so), however, a hydrogen effect on ITO reduction is more pronounced and the ITO surface is more reduced by CH{sub 3}{sup +} ions than CH{sup +} ions. Although the surface is covered more with metallic In by low-energy incident CH{sub 3}{sup +} ions than CH{sup +} ions and metallic In is in general less resistant against physical sputtering than its oxide, the ITO sputtering yield by incident CH{sub 3}{sup +} ions is found to be lower than that by incident CH{sup +} ions in this energy range. A postulation to account for the relation between the observed sputtering yield and reduction of the ITO surface is also presented. The results presented here offer a better understanding of elementary surface reactions observed in reactive ion etching processes of ITO by hydrocarbon plasmas.

Determination of trace amounts of indium in some sediments by means of coprecipitation with zirconium hydroxide and differential pulse anodic stripping voltammetry

International Nuclear Information System (INIS)

Yoshimura, Wataru; Uzawa, Atushi; Hong Luxin.

1994-01-01

Indium in some sediments was determined by means of coprecipitation and differential pulse anodic stripping voltammetry. The analytical procedure was as follows. Fifty milliliters of distilled water is added to 10 ml of sample solution containing 0.04 g of sediment. Then, constant amounts of indium standard solution and 1 ml of zirconium oxychloride solution are added and the pH adjusted to 8.8 with ammonia water (1:2). The precipitate is separated by filtration and then dissolved in 25 ml of 4 M hydrochloric acid. After 1 ml of 5% KCNS solution is added, this solution is diluted to 50 ml with distilled water. A portion of this solution is employed for the determination of indium. After bubbling nitrogen gas through the sample solution for 100 s it was pre-electrolyzed for 100 s. The potential was scanned from -0.9 V to -0.3 Vυs. SCE for dissolution of indium ion. Indium ion was determined from the peak current of the voltammogram. The results are as follows: (1) Zirconium hydroxide was the most effective collector of indium when the pH was adjusted to 8.8 with ammonia water (1:2). (2) Iron (III) and cadmium ions were found to interfere with the determination of indium. (3) The analytical procedure took about 90 min and 0.01 ppm of indium in sample solution could be determined. (4) This method is applicable to the determination of indium in river bottom and sea floor sediment. (author)

Observation of indium ion migration-induced resistive switching in Al/Mg_0_._5Ca_0_._5TiO_3/ITO

International Nuclear Information System (INIS)

Lin, Zong-Han; Wang, Yeong-Her

2016-01-01

Understanding switching mechanisms is very important for resistive random access memory (RRAM) applications. This letter reports an investigation of Al/Mg_0_._5Ca_0_._5TiO_3 (MCTO)/ITO RRAM, which exhibits bipolar resistive switching behavior. The filaments that connect Al electrodes with indium tin oxide electrodes across the MCTO layer at a low-resistance state are identified. The filaments composed of In_2O_3 crystals are observed through energy-dispersive X-ray spectroscopy, high-resolution transmission electron microscopy, nanobeam diffraction, and comparisons of Joint Committee on Powder Diffraction Standards (JCPDS) cards. Finally, a switching mechanism resulting from an electrical field induced by In"3"+ ion migration is proposed. In"3"+ ion migration forms/ruptures the conductive filaments and sets/resets the RRAM device.

Evolution of end-of-range damage and transient enhanced diffusion of indium in silicon

Science.gov (United States)

Noda, T.

2002-01-01

Correlation of evolution of end-of-range (EOR) damage and transient enhanced diffusion (TED) of indium has been studied by secondary ion mass spectrometry and transmission electron microscopy. A physically based model of diffusion and defect growth is applied to the indium diffusion system. Indium implantation with 200 keV, 1×1014/cm2 through a 10 nm screen oxide into p-type Czochralski silicon wafer was performed. During postimplantation anneal at 750 °C for times ranging from 2 to 120 min, formation of dislocation loops and indium segregation into loops were observed. Simulation results of evolution of EOR defects show that there is a period that {311} defects dissolve and release free interstitials before the Ostwald ripening step of EOR dislocation loops. Our diffusion model that contains the interaction between indium and loops shows the indium pileup to the loops. Indium segregation to loops occurs at a pure growth step of loops and continues during the Ostwald ripening step. Although dislocation loops and indium segregation in the near-surface region are easily dissolved by high temperature annealing, EOR dislocation loops in the bulk region are rigid and well grown. It is considered that indium trapped by loops with a large radius is energetically stable. It is shown that modeling of the evolution of EOR defects is important for understanding indium TED.

Evidence for atomic scale disorder in indium nitride from perturbed angular correlation spectroscopy

International Nuclear Information System (INIS)

Dogra, R; Shrestha, S K; Byrne, A P; Ridgway, M C; Edge, A V J; Vianden, R; Penner, J; Timmers, H

2005-01-01

The crystal lattice of bulk grains and state-of-the-art films of indium nitride was investigated at the atomic scale with perturbed angular correlation spectroscopy using the 111 In/Cd radioisotope probe. The probe was introduced during sample synthesis, by diffusion and by ion implantation. The mean quadrupole interaction frequency ν Q = 28 MHz was observed at the indium probe site in all types of indium nitride samples with broad frequency distributions. The observed small, but non-zero, asymmetry parameter indicates broken symmetry around the probe atoms. Results have been compared with theoretical calculations based on the point charge model. The consistency of the experimental results and their independence of the preparation technique suggest that the origin of the broad frequency distribution is inherent to indium nitride, indicating a high degree of disorder at the atomic scale. Due to the low dissociation temperature of indium nitride, furnace and rapid thermal annealing at atmospheric pressure reduce the lattice disorder only marginally

Preparation of High-purity Indium Oxalate Salt from Indium Scrap by Organic Acids

International Nuclear Information System (INIS)

Koo, Su-Jin; Ju, Chang-Sik

2013-01-01

Effect of organic acid on the preparation of indium-oxalate salt from indium scraps generated from ITO glass manufacturing process was studied. Effects of parameters, such as type and concentration of organic acids, pH of reactant, temperature, reaction time on indium-oxalate salt preparation were examined. The impurity removal efficiency was similar for both oxalic acid and citric acid, but citric acid did not make organic acid salt with indium. The optimum conditions were 1.5 M oxalic acid, pH 7, 80 .deg. C, and 6 hours. On the other hand, the recoveries increased with pH, but the purity decreased. The indium-oxalate salt purity prepared by two cycles was 99.995% (4N5). The indium-oxalate salt could be converted to indium oxide and indium metal by substitution reaction and calcination

Recovery of indium ions by nanoscale zero-valent iron

Energy Technology Data Exchange (ETDEWEB)

Chen, Wen; Su, Yiming [Tongji University, State Key Laboratory of Pollution Control and Resources Reuse (China); Wen, Zhipan [Wuhan Institute of Technology, School of Chemistry and Environmental Engineering (China); Zhang, Yalei; Zhou, Xuefei, E-mail: zhouxuefei@tongji.edu.cn; Dai, Chaomeng, E-mail: daichaomeng@tongji.edu.cn [Tongji University, State Key Laboratory of Pollution Control and Resources Reuse (China)

2017-03-15

Indium and its compounds have plenty of industrial applications and high demand. Therefore, indium recovery from various industrial effluents is necessary. It was sequestered by nanoscale zero-valent iron (nZVI) whose size mainly ranged from 50 to 70 nm. Adsorption kinetics and isotherm, influence of pH, and ionic strength were thoroughly investigated. The reaction process was well fitted to a pseudo second-order model, and the maximum adsorption capacity of In(III) was 390 mg In(III)/g nZVI similar to 385 mg In(III)/g nZVI at 298 K calculated by Langmuir model. The mole ratio of Fe(II) released to In(III) immobilized was 3:2, which implied a special chemical process of co-precipitation combined Fe(OH){sub 2} with In(OH){sub 3}. Transmission electron microscopy with an energy-disperse X-ray (TEM-EDX), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) were used to characterize surface morphology, corrosion products, and valence state of indium precipitate formed on nanoparticles. The structural evolution changed from core-shell structure of iron oxide to sheet structure of co-precipitation, to sphere structure that hydroxide gradually dissolved as the pH decreased, and to cavity structures for the pH continually decreased. Furthermore, below pH 4.7, the In(III) enrichment was inhibited for the limited capacity of co-precipitation. Also, it was found that Ca{sup 2+} and HPO{sub 4}{sup 2−} have more negative influence on In(III) recovery compared with Na{sup +}, NO{sub 3}{sup −}, HCO{sub 3}{sup −}, and SO{sub 4}{sup 2−}. Therefore, the In(III) recovery can be described by a mechanism which consists of adsorption, co-precipitation, and reduction and was over 78% even after 3 cycles. The results confirmed that it was applicable to employ nZVI for In(III) immobilization.

Plastic deformation of indium nanostructures

International Nuclear Information System (INIS)

Lee, Gyuhyon; Kim, Ju-Young; Burek, Michael J.; Greer, Julia R.; Tsui, Ting Y.

2011-01-01

Highlights: → Indium nanopillars display two different deformation mechanisms. → ∼80% exhibited low flow stresses near that of bulk indium. → Low strength nanopillars have strain rate sensitivity similar to bulk indium. → ∼20% of compressed indium nanopillars deformed at nearly theoretical strengths. → Low-strength samples do not exhibit strength size effects. - Abstract: Mechanical properties and morphology of cylindrical indium nanopillars, fabricated by electron beam lithography and electroplating, are characterized in uniaxial compression. Time-dependent deformation and influence of size on nanoscale indium mechanical properties were investigated. The results show two fundamentally different deformation mechanisms which govern plasticity in these indium nanostructures. We observed that the majority of indium nanopillars deform at engineering stresses near the bulk values (Type I), with a small fraction sustaining flow stresses approaching the theoretical limit for indium (Type II). The results also show the strain rate sensitivity and flow stresses in Type I indium nanopillars are similar to bulk indium with no apparent size effects.

Laser-spectroscopic nuclear-structure studies on radioactive silver and indium isotopes

International Nuclear Information System (INIS)

Dinger, U.

1988-05-01

Neutron-deficient silver and neutron-rich indium isotopes were studied by collinear laser spectroscopy. The neutron-deficient nuclei 101 , 103 , 104 , 105 , 105m , 106m Ag were produced as evaporation-residual nuclei in heavy-ion fusion reactions at the mass separator of the GSI in Darmstadt. The fourteen studied indium isotopes and isomers with even mass number in the range 112-126 In were produced by 600-MeV-proton induced fission of a uranium carbide target at the ISOLDE separator in Geneva. The mass-separated ion beam was subsequently deviated electrostatically, neutralized in a sodium vapor and superposed with a c w dye laser. A photon counting system detected the resonance fluorescence of the induced transitions. The hyperfine structure and the isotope shift of the 4d 9 5s 2 2 D 5/2 → 4d 10 6p 2 P 3/2 transition (λ=547.7 nm) in silver and the 5p 2 P 1/2,3/2 → 6s 2 s 1/2 transition (λ=410 respectively 451 nm) in indium were measured. While in indium for the analysis of the data earlier work could be referred to, in silver a detailed analysis of the isotope shift and hyperfine structure was performed by means of ab initio calculations and semi-empirical procedures. Thereby the configuration interactions were especially considered. The nuclear moments were discussed in the framework of existing nuclear models regarding nuclear-spectroscopic informations. (orig./HSI) [de

[Mechanism of renal elimination of 2 elements of group IIIA of the periodic table : aluminum and indium].

Science.gov (United States)

Galle, P

1981-01-05

Aluminium and indium, two elements of group IIIA of the periodic table, are concentrated by the kidney inside lysosomes of proximal tubule cell. In these lysosomes, aluminium and indium are precipitated as non-soluble phosphate salts and these precipitates are then expelled in the tubular lumen and eliminated with the urinary flow. These data have been visualized by analytical microscopy (ion microscopy and X ray microanalysis). Local acid phosphatases are assumed to permit the concentration of aluminium and indium salts inside the lysosomes.

Extraction of aluminium, gallium and indium by tri-n-octylamine from citric acid solutions

International Nuclear Information System (INIS)

Bol'shova, T.A.; Kaplunova, A.M.; Ershova, N.I.; Varshal, E.B.

1984-01-01

A study was made on aluminium, gallium and indium distribution in triocylam ine(toa)-citric acid system depending on pH of aqueous solution, concentration of components and foreign electrolytes. The methods of equilibrium shift, compe ting ions and isomolar series were used to find the component ratio in toa: Me: citric acid complexes equal to 3:1:2. The equation describing the extraction of citrate gallium, indium and aluminium complexes by trioctylamine was suggested. Using the difference in extraction behavior of the elements of aluminium, yttri um and lanthanum subgroup the extraction-chromatographic method of their separat ion, applied for the analysis of optical glasses was developed. The method is c haracterized by satisfactory reproduction, simplicity and expre

Perturbed angular correlation study of the ion exchange of indium into silicalite zeolites

International Nuclear Information System (INIS)

Ramallo-Lopez, J.M.; Requejo, F.G.; Renteria, M.; Bibiloni, A.G.; Miro, E.E.

1999-01-01

Two indium-containing silicalite zeolites (In/H-ZSM5) catalysts prepared by wet impregnation and ionic exchange were characterized by the Perturbed Angular Correlation (PAC) technique using 111 In as probe to determine the nature of the indium species. Some of these species take part in the catalytic reaction of the selective reduction (SCR) of NO x with methane. PAC experiments were performed at 500 deg. C in air before and after reduction-reoxidation treatments on the catalysts in order to determine the origin of the different hyperfine interactions and then the degree of ionic exchange. Complementary catalytic activity characterizations were also performed.PAC experiments performed on the catalyst obtained by wet impregnation showed that all In-atoms form In 2 O 3 crystallites while almost 70% of In-atoms form In 2 O 3 in the catalyst obtained by ionic exchange. The PAC experiments of both catalysts performed after the reduction-reoxidation treatment revealed the presence of two hyperfine interactions, different from those corresponding to indium in In 2 O 3 . These hyperfine interactions should be associated to disperse In species responsible of the catalytic activity located in the ionic exchange-sites of the zeolites

Poly-crystallinity of indium-tin-oxide films improved by using simultaneous ion beam and heat treatment of the plastic substrate

International Nuclear Information System (INIS)

Son, Phil Kook; Kim, Tae Hyung; Choi, Suk Won; Gwag, Jin Seog

2012-01-01

The combined treatment effects of an ion beam with directionality and heat of a low temperature on a plastic substrate was investigated as a method to increase the electrical conductivity of indium tinoxide (ITO) films deposited on plastic substrate surfaces at low temperatures. Polyethylene terephthalate (PET) surface treatment by using an ion beam at low temperature (120 .deg. C), which can be applied to plastic substrates, improves the conductivity of ITO films. X-ray diffraction indicates that ITO films deposited on PET surfaces treated simultaneously by using an ion beam and heat of a low temperature have an almost polycrystalline structure even though they have small amorphous party on. As a supplementary measurement, the contact angle showed that the polycrystalline structure was due to a self-assembly effect at the PET surfaces. Consequently, the electrical conductivity of an ITO film deposited by using the proposed technique is three times higher than that of an ITO film treated only with heat of low temperature due to the improved polycrystalline structure.

Peculiarities of the interaction of indium-tin and indium-bismuth alloys with ammonium halides

International Nuclear Information System (INIS)

Red'kin, A.N.; Smirnov, V.A.; Sokolova, E.A.; Makovej, Z.I.; Telegin, G.F.

1990-01-01

Peculiarities of fusible metal alloys interaction with ammonium halogenides in vertical reactor are considered using indium-tin and indium-bismuth binary alloys. It is shown that at the end of the process the composition of metal and salt phases is determined by the equilibrium type and constant characteristic of the given salt-metal system. As a result the interaction of indium-tin and indium-bismuth alloys with ammonium halogenides leads to preferential halogenation of indium-bismuth alloys with ammonium halogenides leads to preferential halogenation of indium which may be used in the processes of separation or purification. A model is suggested to calculate the final concentration of salt and metal phase components

Laser- and gamma-induced transformations of optical spectra of indium-doped sodium borate glass

CERN Document Server

Kopyshinsky, O V; Zelensky, S E; Danilchenko, B A; Shakhov, O P

2003-01-01

The optical absorption and luminescence properties of indium-doped sodium borate glass irradiated by gamma-rays and by powerful UV lasers within the impurity-related absorption band are investigated experimentally. It is demonstrated that both the laser- and gamma-irradiation cause similar transformations of optical spectra in the UV and visible regions. The changes of the spectra observed are described with the use of a model which includes three types of impurity centres formed by differently charged indium ions.

Analysis and calibration of transient enhanced diffusion for an indium impurity in a nanoscale semiconductor device

International Nuclear Information System (INIS)

Lee, Jun-Ha; Lee, Hoong-Joo

2005-01-01

We developed a new systematic calibration procedure which was applied to the prediction of the diffusivity, the segregation, and transient enhanced diffusion (TED) of an indium impurity. The TED of the indium impurity was studied using four different experimental conditions. Although indium is susceptible to TED, rapid thermal annealing (RTA) is effective in suppressing the TED effect and maintaining a steep retrograde profile. Like boron impurities, the indium shows significant oxidation-enhanced diffusion in silicon and has segregation coefficients much less than 1 at the Si/SiO 2 interface. In contrast to boron, the segregation coefficient of indium decreases as the temperature increases. The accuracy of the proposed procedure was validated by using secondary ion mass spectrometry (SIMS) data and by using the 0.13-μm device characteristics, such as V th and I dsat , for which the differences between simulation and experiment less than 5 %.

Effects of oxygen gas flow rate and ion beam plasma conditions on the opto-electronic properties of indium molybdenum oxide films fabricated by ion beam-assisted evaporation

International Nuclear Information System (INIS)

Kuo, C.C.; Liu, C.C.; Lin, C.C.; Liou, Y.Y.; He, J.L.; Chen, F.S.

2008-01-01

The purpose of the present work is to experimentally study the effects of the oxygen gas flow rate and ion beam plasma conditions on the properties of indium molybdenum oxide (IMO) films deposited onto the polyethersulfone (PES) substrate. Crystal structure, surface morphology, and optoelectronic properties of IMO films are examined as a function of oxygen gas flow rate and ion beam discharge voltage. Experimental results show that the IMO films consist of a cubic bixbyite B-In 2 O 3 single phase with its crystal preferred orientation alone B(222). Mo 6+ ions are therefore considered to partially substitute In 3+ sites in the deposit. Under-controlled ion bombardment during deposition enhances the reaction among those arriving oxygen and metal ion species to condense into IMO film and facilitates a decreased surface roughness of IMO film. The film with ultimate crystallinity and the lowest surface roughness is obtained when the oxygen flow rate of 3 sccm and the discharge voltage of 110 V are employed. This results in the lowest electrical resistivity due mainly to the increased Hall mobility and irrelevant to carrier concentration. The lowest electrical resistivity of 8.63 x 10 -4 ohm-cm with a 84.63% transmittance at a wavelength of 550 nm can be obtained, which satisfies the requirement of a flexible transparent conductive polymer substrate

Germanium and indium

Science.gov (United States)

Shanks, W.C. Pat; Kimball, Bryn E.; Tolcin, Amy C.; Guberman, David E.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Germanium and indium are two important elements used in electronics devices, flat-panel display screens, light-emitting diodes, night vision devices, optical fiber, optical lens systems, and solar power arrays. Germanium and indium are treated together in this chapter because they have similar technological uses and because both are recovered as byproducts, mainly from copper and zinc sulfides.The world’s total production of germanium in 2011 was estimated to be 118 metric tons. This total comprised germanium recovered from zinc concentrates, from fly ash residues from coal burning, and from recycled material. Worldwide, primary germanium was recovered in Canada from zinc concentrates shipped from the United States; in China from zinc residues and coal from multiple sources in China and elsewhere; in Finland from zinc concentrates from the Democratic Republic of the Congo; and in Russia from coal.World production of indium metal was estimated to be about 723 metric tons in 2011; more than one-half of the total was produced in China. Other leading producers included Belgium, Canada, Japan, and the Republic of Korea. These five countries accounted for nearly 95 percent of primary indium production.Deposit types that contain significant amounts of germanium include volcanogenic massive sulfide (VMS) deposits, sedimentary exhalative (SEDEX) deposits, Mississippi Valley-type (MVT) lead-zinc deposits (including Irish-type zinc-lead deposits), Kipushi-type zinc-lead-copper replacement bodies in carbonate rocks, and coal deposits.More than one-half of the byproduct indium in the world is produced in southern China from VMS and SEDEX deposits, and much of the remainder is produced from zinc concentrates from MVT deposits. The Laochang deposit in Yunnan Province, China, and the VMS deposits of the Murchison greenstone belt in Limpopo Province, South Africa, provide excellent examples of indium-enriched deposits. The SEDEX deposits at Bainiuchang, China (located in

An electric detection of immunoglobulin G in the enzyme-linked immunosorbent assay using an indium oxide nanoparticle ion-sensitive field-effect transistor

International Nuclear Information System (INIS)

Lee, Dongjin; Cui, Tianhong

2012-01-01

Semiconducting nanoparticle ion-sensitive field-effect transistors (ISFETs) are used to detect immunoglobulin G (IgG) in the conventional enzyme-linked immunosorbent assay (ELISA). Indium oxide and silica nanoparticles were layer-by-layer self-assembled with the oppositely charged polyelectrolyte as the electrochemical transducer and antibody immobilization site, respectively. The assay was conducted on a novel platform of indium oxide nanoparticle ISFETs, where the electric signals are generated in response to the concentration of target IgG using the labeled detecting antibody. The sandwiched ELISA structure catalyzed the conversion of the acidic substrate into neutral substance with the aid of horseradish peroxidase. The pH change in the substrate solution was detected by nanoparticle ISFETs. Normal rabbit IgG was used as a model antigen whose detection limit of 0.04 ng ml −1 was found. The facile electric detection in the conventional assay through the semiconducting nanoparticle ISFET has potential applications as a point-of-care detection or a sensing element in a lab-on-a-chip system

Enhanced photocatalytic activity of titania with unique surface indium and boron species

Science.gov (United States)

Yu, Yanlong; Wang, Enjun; Yuan, Jixiang; Cao, Yaan

2013-05-01

Indium and boron co-doped TiO2 photocatalysts were prepared by a sol-gel method. The structure and properties of photocatalysts were characterized by XRD, BET, XPS, UV-vis DRS and PL techniques. It is found that boron is mainly doped into the lattice of TiO2 in interstitial mode, while indium is present as unique chemical species of O-In-Clx (x = 1 or 2) on the surface. Compared with pure TiO2, the narrowness of band gap of TiO2 doped with indium and boron is due to the mixed valence band formed by B2p of interstitial doped B ions hybridized with lattice O2p. And the surface state energy levels of O-In-Clx (x = 1 or 2) and B2O3 species were located at about 0.4 and 0.3 eV below the conduction band respectively, which could lead to significant absorption in the visible-light region and facilitated the effectually separation of photogenerated carriers. Therefore, indium and boron co-doped TiO2 showed the much higher photocatalytic activities than pure TiO2, boron doped TiO2 (TiO2-B) and indium doped TiO2 (TiO2-In) under visible and UV light irradiation.

Perturbed angular correlation study of the ion exchange of indium into silicalite zeolites

Energy Technology Data Exchange (ETDEWEB)

Ramallo-Lopez, J.M., E-mail: requejo@venus.fisica.unlp.edu.ar; Requejo, F.G., E-mail: requejo@venus.fisica.unlp.edu.ar; Renteria, M., E-mail: requejo@venus.fisica.unlp.edu.ar; Bibiloni, A.G. [UNLP, Programa TENAES (CONICET) and Departamento de Fisica, Faculdad Cs Ex (Argentina)], E-mail: requejo@venus.fisica.unlp.edu.ar; Miro, E.E. [UNL, INCAPE (CONICET) and Faculdad Ing. Quimica (Argentina)

1999-09-15

Two indium-containing silicalite zeolites (In/H-ZSM5) catalysts prepared by wet impregnation and ionic exchange were characterized by the Perturbed Angular Correlation (PAC) technique using {sup 111}In as probe to determine the nature of the indium species. Some of these species take part in the catalytic reaction of the selective reduction (SCR) of NO{sub x} with methane. PAC experiments were performed at 500 deg. C in air before and after reduction-reoxidation treatments on the catalysts in order to determine the origin of the different hyperfine interactions and then the degree of ionic exchange. Complementary catalytic activity characterizations were also performed.PAC experiments performed on the catalyst obtained by wet impregnation showed that all In-atoms form In{sub 2}O{sub 3} crystallites while almost 70% of In-atoms form In{sub 2}O{sub 3} in the catalyst obtained by ionic exchange. The PAC experiments of both catalysts performed after the reduction-reoxidation treatment revealed the presence of two hyperfine interactions, different from those corresponding to indium in In{sub 2}O{sub 3}. These hyperfine interactions should be associated to disperse In species responsible of the catalytic activity located in the ionic exchange-sites of the zeolites.

Oxygen-ion-migration-modulated bipolar resistive switching and complementary resistive switching in tungsten/indium tin oxide/gold memory device

Science.gov (United States)

Wu, Xinghui; Zhang, Qiuhui; Cui, Nana; Xu, Weiwei; Wang, Kefu; Jiang, Wei; Xu, Qixing

2018-06-01

In this paper, we report our investigation of room-temperature-fabricated tungsten/indium tin oxide/gold (W/ITO/Au) resistive random access memory (RRAM), which exhibits asymmetric bipolar resistive switching (BRS) behavior. The device displays good write/erase endurance and data retention properties. The device shows complementary resistive switching (CRS) characteristics after controlling the compliance current. A WO x layer electrically formed at the W/ITO in the forming process. Mobile oxygen ions within ITO migrate toward the electrode/ITO interface and produce a semiconductor-like layer that acts as a free-carrier barrier. The CRS characteristic here can be elucidated in light of the evolution of an asymmetric free-carrier blocking layer at the electrode/ITO interface.

New beam for the CERN fixed target heavy ion programme

CERN Document Server

Hill, C E; O'Neill, M

2002-01-01

The physicists of the CERN heavy ion community (SPS fixed target physics) have requested lighter ions than the traditional lead ions, to scale their results and to check their theories. Studies have been carried out to investigate the behaviour of the ECR4 for the production of an indium beam. Stability problems and the low melting point of indium required some modifications to the oven power control system which will also benefit normal lead ion production. Present results of the source behaviour and the ion beam characteristics will be presented.

Mass measurements of neutron-rich indium isotopes toward the N =82 shell closure

Science.gov (United States)

Babcock, C.; Klawitter, R.; Leistenschneider, E.; Lascar, D.; Barquest, B. R.; Finlay, A.; Foster, M.; Gallant, A. T.; Hunt, P.; Kootte, B.; Lan, Y.; Paul, S. F.; Phan, M. L.; Reiter, M. P.; Schultz, B.; Short, D.; Andreoiu, C.; Brodeur, M.; Dillmann, I.; Gwinner, G.; Kwiatkowski, A. A.; Leach, K. G.; Dilling, J.

2018-02-01

Precise mass measurements of the neutron-rich In-130125 isotopes have been performed with the TITAN Penning trap mass spectrometer. TITAN's electron beam ion trap was used to charge breed the ions to charge state q =13 + thus providing the necessary resolving power to measure not only the ground states but also isomeric states at each mass number. In this paper, the properties of the ground states are investigated through a series of mass differentials, highlighting trends in the indium isotopic chain as compared to its proton-magic neighbor, tin (Z =50 ). In addition, the energies of the indium isomers are presented. The (8-) level in 128In is found to be 78 keV lower than previously thought and the (21 /2- ) isomer in 127In is shown to be lower than the literature value by more than 150 keV.

Extraction of indium from extremely diluted solutions; Gewinnung von Indium aus extrem verduennten Loesungen

Energy Technology Data Exchange (ETDEWEB)

Vostal, Radek; Singliar, Ute; Froehlich, Peter [TU Bergakademie Freiberg (Germany). Inst. fuer Technische Chemie

2017-02-15

The demand for indium is rising with the growth of the electronics industry, where it is mainly used. Therefore, a multistage extraction process was developed to separate indium from a model solution whose composition was adequate to sphalerite ore. The initially very low concentration of indium in the solution was significantly increased by several successive extraction and reextraction steps. The process described is characterized by a low requirement for chemicals and a high purity of the obtained indium oxide.

Separation of In (III)and Cd(II) Using Zirconium Vanadate As Inorganic Ion Exchanger

International Nuclear Information System (INIS)

Massoud, A.; Abou El Nour, F.

2012-01-01

In this work, zirconium vanadate as inorganic ion exchanger was chemically synthesized using homogeneous precipitation technique. The obtained zirconium vanadate was mixed with Indium ions to determine its capacity in aqueous solution using batch experiment. Ion exchange capacity of various metal ions was investigated. Effects of ph, initial concentration, weight of the sorbent and contact time on the adsorption of metals were studied. Chromatographic column methods were applied for separation of indium and cadmium. A fixed bed column of zirconium vanadate was successfully used for separation of indium and cadmium. The recovery percentage of both metal ions was about 98.4% using 2 M HCl and citrate buffer ph 3.5, respectively.

Enhanced photocatalytic activity of titania with unique surface indium and boron species

International Nuclear Information System (INIS)

Yu, Yanlong; Wang, Enjun; Yuan, Jixiang; Cao, Yaan

2013-01-01

Indium and boron co-doped TiO 2 photocatalysts were prepared by a sol–gel method. The structure and properties of photocatalysts were characterized by XRD, BET, XPS, UV–vis DRS and PL techniques. It is found that boron is mainly doped into the lattice of TiO 2 in interstitial mode, while indium is present as unique chemical species of O–In–Cl x (x = 1 or 2) on the surface. Compared with pure TiO 2 , the narrowness of band gap of TiO 2 doped with indium and boron is due to the mixed valence band formed by B2p of interstitial doped B ions hybridized with lattice O2p. And the surface state energy levels of O–In–Cl x (x = 1 or 2) and B 2 O 3 species were located at about 0.4 and 0.3 eV below the conduction band respectively, which could lead to significant absorption in the visible-light region and facilitated the effectually separation of photogenerated carriers. Therefore, indium and boron co-doped TiO 2 showed the much higher photocatalytic activities than pure TiO 2 , boron doped TiO 2 (TiO 2 –B) and indium doped TiO 2 (TiO 2 –In) under visible and UV light irradiation.

Optical and Electrical Characterization of Melt-Grown Bulk Indium Gallium Arsenide and Indium Arsenic Phosphide Alloys

Science.gov (United States)

2011-03-01

spectrum, photoluminescence (PL), and refractive index measurements. Other methods such as infrared imagery and micro probe wavelength dispersing ...States. AFIT/DS/ENP/11-M02 OPTICAL AND ELECTRICAL CHARACTERIZATION OF MELT- GROWN BULK INDIUM GALLIUM ARSENIDE AND INDIUM ARSENIC PHOSPHIDE ...CHARACTERIZATION OF MELT-GROWN BULK INDIUM GALLIUM ARSENIDE AND INDIUM ARSENIC PHOSPHIDE ALLOYS Jean Wei, BS, MS Approved

The effect of oxygen ion beam bombardment on the properties of tin indium oxide/polyethylene terephthalate complex

International Nuclear Information System (INIS)

Li, Li; Liu, Honglin; Zou, Lin; Ding, Wanyu; Ju, Dongying; Chai, Weiping

2013-01-01

The tin indium oxide (ITO) films were deposited onto the polyethylene terephthalate (PET) surface that has been bombarded by an O ion beam. The variation of the O bombardment time resulted in the production of ITO/PET complex with different properties. Characterization by four-point probe measurement after the bending fatigue test showed that the adhesion property of the ITO/PET complex could be improved by the increase of O bombardment time while little change of electrical resistivity was observed. Scanning electron microscopy results showed that after the bending fatigue test, the nano scale seams and micro scale trenches appeared at the surface of the ITO/PET complex. The former was only the cracks of ITO film, which has little influence on the continuity and electrical resistivity of ITO film. On the contrary, the micro scale trenches were caused by the peeling off of ITO chips at the cracks, which mainly influenced the continuity and electrical resistivity of ITO film. With the increase of O bombardment time, the number and length of the micro scale trenches decreased. X-ray photoelectron spectrometry characterization showed that with the increase of O bombardment time, parts of the methylene C bonds were transformed into C=O bonds, which could be broken to form C-O-In(Sn) bonds at the initial stage of ITO film growth. By these C-O-In(Sn) crosslink bonds, the ITO film could adhere well onto the PET and the ITO/PET complex display better anti-bending fatigue property. Finally, in the context of the application of the ITO/PET complex as a flexible electrode substrate, the present work reveals a simple way to crosslink them, as well as the physicochemical mechanism happening at the interface of complex. - Highlights: • Polyethylene terephthalate (PET) surface was bombarded by N ions. • Tin indium oxide (ITO) film was deposited on bombarded PET surface. • By bombardment, methylene C bond on PET surface was broken and replaced by C=O bond. • C=O bond was

The effect of oxygen ion beam bombardment on the properties of tin indium oxide/polyethylene terephthalate complex

Energy Technology Data Exchange (ETDEWEB)

Li, Li; Liu, Honglin; Zou, Lin [School of Materials Science and Engineering, Dalian Jiaotong University, Dalian 116028 (China); Ding, Wanyu, E-mail: dwysd_2000@163.com [School of Materials Science and Engineering, Dalian Jiaotong University, Dalian 116028 (China); Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116028 (China); Ju, Dongying [Department of Material Science and Engineering, Saitama Institute of Technology, Fukaya 369-0293 (Japan); Chai, Weiping [School of Materials Science and Engineering, Dalian Jiaotong University, Dalian 116028 (China)

2013-10-31

The tin indium oxide (ITO) films were deposited onto the polyethylene terephthalate (PET) surface that has been bombarded by an O ion beam. The variation of the O bombardment time resulted in the production of ITO/PET complex with different properties. Characterization by four-point probe measurement after the bending fatigue test showed that the adhesion property of the ITO/PET complex could be improved by the increase of O bombardment time while little change of electrical resistivity was observed. Scanning electron microscopy results showed that after the bending fatigue test, the nano scale seams and micro scale trenches appeared at the surface of the ITO/PET complex. The former was only the cracks of ITO film, which has little influence on the continuity and electrical resistivity of ITO film. On the contrary, the micro scale trenches were caused by the peeling off of ITO chips at the cracks, which mainly influenced the continuity and electrical resistivity of ITO film. With the increase of O bombardment time, the number and length of the micro scale trenches decreased. X-ray photoelectron spectrometry characterization showed that with the increase of O bombardment time, parts of the methylene C bonds were transformed into C=O bonds, which could be broken to form C-O-In(Sn) bonds at the initial stage of ITO film growth. By these C-O-In(Sn) crosslink bonds, the ITO film could adhere well onto the PET and the ITO/PET complex display better anti-bending fatigue property. Finally, in the context of the application of the ITO/PET complex as a flexible electrode substrate, the present work reveals a simple way to crosslink them, as well as the physicochemical mechanism happening at the interface of complex. - Highlights: • Polyethylene terephthalate (PET) surface was bombarded by N ions. • Tin indium oxide (ITO) film was deposited on bombarded PET surface. • By bombardment, methylene C bond on PET surface was broken and replaced by C=O bond. • C=O bond was

Quantitative STEM on indium containing group III-V semiconductor nanostructures

International Nuclear Information System (INIS)

Mehrtens, Thorsten

2013-01-01

In the framework of this thesis. a method for compositional analysis of semiconductor nanostructures is applied on technologically relevant group III-V alloys. It is based on a quantitative comparison between intensities of experimentally acquired High-Angle Annular Dark Field Scanning Tansmission Electron Microscopy (HAADF-STEM) images and simulated intensities from multislice calculations in the frozen lattice approach. The demonstrated method allows determination of specimen thickness and material composition on subnanometer scale. Since quantitative HAADF-STEM is still a very young technique, its applicability has only been proven for a few materials, yet. Thus, the main goal of this thesis is the simulation of suitable reference datasets for different ternary semiconducting alloys and to test their reliability by complementary analysis. A total of three different semiconducting materials are thereby analyzed (InGaN, InGaAs and InAlN) that have all in common that they contain indium. The main focus of this work lies on InGaN which is due to its bandgap particularly suitable for the fabrication of optoelectronic devices operating in the visible spectrum of the light. In the first part of the presented results, the quality of ultra-thin TEM-specimens prepared by techniques involving ion milling at high energies is optimized. This is done by an additional ion milling step where the impinging ions possess an energy of only 400 eV. It is found that the preparation induced amorphous surface layer that occurs during ion milling can be drastically reduced below 1 nm. The second part concentrates on results obtained on InGaN. Here, different simulations in the frozen lattice approach are carried out under certain conditions. These simulations either include or do not include thermal diffuse scattering and/or static atomic displacement to demonstrate their influence on the amount of intensity measured in the experiment. As the consideration of thermal diffuse scattering

Enhanced photocatalytic activity of titania with unique surface indium and boron species

Energy Technology Data Exchange (ETDEWEB)

Yu, Yanlong; Wang, Enjun; Yuan, Jixiang [MOE Key Laboratory of Weak-Light Nonlinear Photonics, TEDA Applied Physics School and School of Physics, Nankai University, Tianjin 300457 (China); Cao, Yaan, E-mail: caoyaan@yahoo.com [MOE Key Laboratory of Weak-Light Nonlinear Photonics, TEDA Applied Physics School and School of Physics, Nankai University, Tianjin 300457 (China)

2013-05-15

Indium and boron co-doped TiO{sub 2} photocatalysts were prepared by a sol–gel method. The structure and properties of photocatalysts were characterized by XRD, BET, XPS, UV–vis DRS and PL techniques. It is found that boron is mainly doped into the lattice of TiO{sub 2} in interstitial mode, while indium is present as unique chemical species of O–In–Cl{sub x} (x = 1 or 2) on the surface. Compared with pure TiO{sub 2}, the narrowness of band gap of TiO{sub 2} doped with indium and boron is due to the mixed valence band formed by B2p of interstitial doped B ions hybridized with lattice O2p. And the surface state energy levels of O–In–Cl{sub x} (x = 1 or 2) and B{sub 2}O{sub 3} species were located at about 0.4 and 0.3 eV below the conduction band respectively, which could lead to significant absorption in the visible-light region and facilitated the effectually separation of photogenerated carriers. Therefore, indium and boron co-doped TiO{sub 2} showed the much higher photocatalytic activities than pure TiO{sub 2}, boron doped TiO{sub 2} (TiO{sub 2}–B) and indium doped TiO{sub 2} (TiO{sub 2}–In) under visible and UV light irradiation.

Increased p-type conductivity through use of an indium surfactant in the growth of Mg-doped GaN

Science.gov (United States)

Kyle, Erin C. H.; Kaun, Stephen W.; Young, Erin C.; Speck, James S.

2015-06-01

We have examined the effect of an indium surfactant on the growth of p-type GaN by ammonia-based molecular beam epitaxy. p-type GaN was grown at temperatures ranging from 700 to 780 °C with and without an indium surfactant. The Mg concentration in all films in this study was 4.5-6 × 1019 cm-3 as measured by secondary ion mass spectroscopy. All p-type GaN films grown with an indium surfactant had higher p-type conductivities and higher hole concentrations than similar films grown without an indium surfactant. The lowest p-type GaN room temperature resistivity was 0.59 Ω-cm, and the highest room temperature carrier concentration was 1.6 × 1018 cm-3. Fits of the temperature-dependent carrier concentration data showed a one to two order of magnitude lower unintentional compensating defect concentration in samples grown with the indium surfactant. Samples grown at higher temperature had a lower active acceptor concentration. Improvements in band-edge luminescence were seen by cathodoluminescence for samples grown with the indium surfactant, confirming the trends seen in the Hall data.

Properties of indium tin oxide films deposited on unheated polymer substrates by ion beam assisted deposition

International Nuclear Information System (INIS)

Yu Zhinong; Li Yuqiong; Xia Fan; Zhao Zhiwei; Xue Wei

2009-01-01

The optical, electrical and mechanical properties of indium tin oxide (ITO) films prepared on polyethylene terephthalate (PET) substrates by ion beam assisted deposition at room temperature were investigated. The properties of ITO films can be improved by introducing a buffer layer of silicon dioxide (SiO 2 ) between the ITO film and the PET substrate. ITO films deposited on SiO 2 -coated PET have better crystallinity, lower electrical resistivity, and improved resistance stability under bending than those deposited on bare PET. The average transmittance and the resistivity of ITO films deposited on SiO 2 -coated PET are 85% and 0.90 x 10 -3 Ω cm, respectively, and when the films are bent, the resistance remains almost constant until a bending radius of 1 cm and it increases slowly under a given bending radius with an increase of the bending cycles. The improved resistance stability of ITO films deposited on SiO 2 -coated PET is mainly attributed to the perfect adhesion of ITO films induced by the SiO 2 buffer layer.

Light forces on an indium atomic beam

International Nuclear Information System (INIS)

Kloeter, B.

2007-01-01

In this thesis it was studied, whether indium is a possible candidate for the nanostructuration respectively atomic lithography. For this known method for the generation and stabilization of the light necessary for the laser cooling had to be fitted to the special properties of indium. The spectroscopy of indium with the 451 nm and the 410 nm light yielded first hints that the formulae for the atom-light interaction for a two-level atom cannot be directly transferred to the indium atom. By means of the obtained parameters of the present experiment predictions for a possible Doppler cooling of the indium atomic beam were calculated. Furthermore the possibility for the direct deposition of indium on a substrate was studied

Sodium enhances indium-gallium interdiffusion in copper indium gallium diselenide photovoltaic absorbers.

Science.gov (United States)

Colombara, Diego; Werner, Florian; Schwarz, Torsten; Cañero Infante, Ingrid; Fleming, Yves; Valle, Nathalie; Spindler, Conrad; Vacchieri, Erica; Rey, Germain; Guennou, Mael; Bouttemy, Muriel; Manjón, Alba Garzón; Peral Alonso, Inmaculada; Melchiorre, Michele; El Adib, Brahime; Gault, Baptiste; Raabe, Dierk; Dale, Phillip J; Siebentritt, Susanne

2018-02-26

Copper indium gallium diselenide-based technology provides the most efficient solar energy conversion among all thin-film photovoltaic devices. This is possible due to engineered gallium depth gradients and alkali extrinsic doping. Sodium is well known to impede interdiffusion of indium and gallium in polycrystalline Cu(In,Ga)Se 2 films, thus influencing the gallium depth distribution. Here, however, sodium is shown to have the opposite effect in monocrystalline gallium-free CuInSe 2 grown on GaAs substrates. Gallium in-diffusion from the substrates is enhanced when sodium is incorporated into the film, leading to Cu(In,Ga)Se 2 and Cu(In,Ga) 3 Se 5 phase formation. These results show that sodium does not decrease per se indium and gallium interdiffusion. Instead, it is suggested that sodium promotes indium and gallium intragrain diffusion, while it hinders intergrain diffusion by segregating at grain boundaries. The deeper understanding of dopant-mediated atomic diffusion mechanisms should lead to more effective chemical and electrical passivation strategies, and more efficient solar cells.

Increased p-type conductivity through use of an indium surfactant in the growth of Mg-doped GaN

Energy Technology Data Exchange (ETDEWEB)

Kyle, Erin C. H., E-mail: erinkyle@engineering.ucsb.edu; Kaun, Stephen W.; Young, Erin C.; Speck, James S. [Materials Department, University of California, Santa Barbara, California 93106 (United States)

2015-06-01

We have examined the effect of an indium surfactant on the growth of p-type GaN by ammonia-based molecular beam epitaxy. p-type GaN was grown at temperatures ranging from 700 to 780 °C with and without an indium surfactant. The Mg concentration in all films in this study was 4.5–6 × 10{sup 19} cm{sup −3} as measured by secondary ion mass spectroscopy. All p-type GaN films grown with an indium surfactant had higher p-type conductivities and higher hole concentrations than similar films grown without an indium surfactant. The lowest p-type GaN room temperature resistivity was 0.59 Ω-cm, and the highest room temperature carrier concentration was 1.6 × 10{sup 18} cm{sup −3}. Fits of the temperature-dependent carrier concentration data showed a one to two order of magnitude lower unintentional compensating defect concentration in samples grown with the indium surfactant. Samples grown at higher temperature had a lower active acceptor concentration. Improvements in band-edge luminescence were seen by cathodoluminescence for samples grown with the indium surfactant, confirming the trends seen in the Hall data.

New indium selenite-oxalate and indium oxalate with two- and three-dimensional structures

International Nuclear Information System (INIS)

Cao Junjun; Li Guodong; Chen Jiesheng

2009-01-01

Two new indium(III) compounds with extended structures, [In 2 (SeO 3 ) 2 (C 2 O 4 )(H 2 O) 2 ].2H 2 O (I) and [NH 3 (CH 2 ) 2 NH 3 ][In(C 2 O 4 ) 2 ] 2 .5H 2 O (II), have been prepared under mild hydrothermal conditions and structurally characterized by single-crystal X-ray diffraction, thermogravimetric analysis and infrared spectroscopy. Compound I crystallizes in the triclinic system, space group P-1, with a=5.2596(11) A, b=6.8649(14) A, c=9.3289(19) A, α=101.78(3) o , β=102.03(3) o , γ=104.52(3) o , while compound II crystallizes in the orthorhombic system, space group Fdd2, with a=15.856(3) A, b=31.183(6) A, c=8.6688(17) A. In compound I, indium-selenite chains are bridged by oxalate units to form two-dimensional (2D) In 2 (SeO 3 ) 2 C 2 O 4 layers, separated by non-coordinating water molecules. In compound II, the indium atoms are connected through the oxalate units to generate a 3D open framework containing cross-linked 12- and 8-membered channels. - Graphical abstract: Two new indium(III) compounds have been hydrothermally synthesized and structurally characterized. In I, the indium-selenite chains are bridged by oxalate units to form 2D In 2 (SeO 3 ) 2 C 2 O 4 layers. In II, the indium atoms are connected through the oxalate units to generate a 3D open framework containing cross-linked 12- and 8-membered ring channels

Growth of CdS thin films on indium coated glass substrates via chemical bath deposition and subsequent air annealing

Energy Technology Data Exchange (ETDEWEB)

Ghosh, Biswajit; Kumar, Kamlesh; Singh, Balwant Kr; Banerjee, Pushan; Das, Subrata, E-mail: neillohit@yahoo.co.in

2014-11-30

Graphical abstract: - Highlights: • CdS film grown on indium coated glass substrates via CBD and subsequent annealing. • Disappearance of the indium (1 1 2) peak confirms interdiffusion at 300 °C. • SIMS indicates the subsequent interdiffusion at progressively higher temperature. • Composite In–CdS layer showed lower photosensitivity compared to pure CdS. - Abstract: In the present work attempts were made to synthesize indium doped CdS films by fabricating In/CdS bilayers using CBD-CdS on vacuum evaporated In thin films and subsequent air annealing. 135 nm CdS films were grown onto 20 nm and 35 nm indium coated glass substrate employing chemical bath deposition technique. The In/CdS bilayers thus formed were subjected to heat treatment at the temperatures between 200 and 400 °C for 4 min in the muffle furnace to facilitate indium to diffuse into the CdS films. XRD pattern ascertained no noticeable shift in lattice constant implying grain boundary metal segregation, while secondary ion mass spectrometry indicated the diffusion profile of indium into CdS matrices. Mass spectrometry results showed that substantial diffusion of indium had been taken place within CdS at 400 °C. Dark and photocurrent with different illumination time were measured to ascertain the photosensitivity of pure and composite CdS films.

Indium recovery by solvent extraction

International Nuclear Information System (INIS)

Fortes, Marilia Camargos Botelho

1999-04-01

Indium has been recovered as a byproduct from residues generated from the sulfuric acid leaching circuits in mineral plants for zinc recovery. Once its recovery comes from the slags of other metals recovery, it is necessary to separate it from the other elements which usually are present in high concentrations. Many works have been approaching this separation and indicate the solvent extraction process as the main technique used. In Brazilian case, indium recovery depends on the knowledge of this technique and its development. This paper describes the solvent extraction knowledge for the indium recovery from aqueous solutions generated in mineral plants. The results for determination of the best experimental conditions to obtain a high indium concentration solution and minimum iron poisoning by solvent extraction with di (2-ethylhexyl)-phosphoric acid (D2EHPA) solubilized in isoparafin and exxsol has been presented. (author)

X-ray photoelectron spectroscopy investigation of ion beam sputtered indium tin oxide films as a function of oxygen pressure during deposition

International Nuclear Information System (INIS)

Nelson, A.J.; Aharoni, H.

1987-01-01

X-ray photoelectron spectroscopy analysis was performed on ion beam sputter deposited films of indium tin oxide as a function of O 2 partial pressure during deposition. The oxygen partial pressure was varied over the range of 2.5 x 10 -6 --4.0 x 10 -5 Torr. Changes in composition as well as in the deconvoluted In 3d 5 /sub // 2 , Sn 3d 5 /sub // 2 , and O 1s core level spectra were observed and correlated with the variation of the oxygen partial pressure during deposition. Results show that the films become increasingly stoichiometric as P/sub =/ is increased and that the excess oxygen introduced during deposition is bound predominantly to the Sn and has little or no effect on the In--O bonding

Preparation of trialkylindium by alkylation of metallic indium

International Nuclear Information System (INIS)

Eremeev, I.V.; Danov, S.M.; Sakhipov, V.R.

1995-01-01

The investigation results on production of trialkyl indium by alkylation of metallic indium are presented. In contradistinction to the known techniques for the production of trialkyls on indium by alkylation it is suggested to separate the synthesis into two steps. At the first step indium is alkylated by alkylhalide to alkyl indium halide, and at the second alkylation is carried out using. Grignard reagent. The techniques for preparation of trimethyl- and triethylindium, developed on the bases of this scheme, are noted for good reproducibility, allow to preclude, agglomeration of indium during the synthesis, as well as to reduce the consumption coefficients, and amounts, of the introduced starting reagents, i.e. magnesium and alkylhalide. Refs. 16

Nanomechanical Characterization of Indium Nano/Microwires

Directory of Open Access Journals (Sweden)

N Kiran MSR

2010-01-01

Full Text Available Abstract Nanomechanical properties of indium nanowires like structures fabricated on quartz substrate by trench template technique, measured using nanoindentation. The hardness and elastic modulus of wires were measured and compared with the values of indium thin film. Displacement burst observed while indenting the nanowire. ‘Wire-only hardness’ obtained using Korsunsky model from composite hardness. Nanowires have exhibited almost same modulus as indium thin film but considerable changes were observed in hardness value.

SPS Ion Induced Desorption Experiment

CERN Multimedia

Maximilien Brice

2003-01-01

This experiment will give a study about the induced desorption from heavy ion (Indium ion run from week 45 in SPS T4-H8 area) impacting LHC type graphite collimator. 4 different samples are located in the 4 chambers 90° one to each other: pure graphite, graphite with copper coating, graphite with NEG coating, 316LN stainless steal (reference).

A study of the kinetics and mechanisms of electrocrystallization of indium oxide on an in situ prepared metallic indium electrode

International Nuclear Information System (INIS)

Omanovic, S.; Metikos-Hukovic, M.

2004-01-01

The mechanisms and kinetics of nucleation and growth of indium oxide film on an in situ prepared metallic indium electrode was studied in a borate buffer solution of pH 10.0 using cyclic voltammetry and chroanoamperometry techniques. It was shown that the initial stage of nucleation of the oxide film includes a three-dimensional progressive nucleation process, combined with a diffusion-controlled growth of the stable indium oxide crystals. The thermodynamic data obtained indicated a strong tendency of indium to form an indium oxide film on its surface in an aqueous solution. It was found that the rate-determining step in the nucleation and growth process is the surface diffusion of electroactive species. The nucleation rate constant, and the number of nucleation active sites were calculated independently. It was shown that between 2 and 15% of sites on the indium surface act as active nucleation centers, and that each active site represents a critical nucleus

Electronic and chemical properties of indium clusters

International Nuclear Information System (INIS)

Rayane, D.; Khardi, S.; Tribollet, B.; Broyer, M.; Melinon, P.; Cabaud, B.; Hoareau, A.

1989-01-01

Indium clusters are produced by the inert gas condensation technique. The ionization potentials are found higher for small clusters than for the Indium atom. This is explained by the p character of the bonding as in aluminium. Doubly charge clusters are also observed and fragmentation processes discussed. Finally small Indium clusters 3< n<9 are found very reactive with hydrocarbon. (orig.)

Wear life of sputtered MoSx films extended by high energy ion implantation

International Nuclear Information System (INIS)

Okazaki, Yasufumi; Fujiura, Hideo; Nishimura, Makoto

2000-01-01

The tribological characteristics of sputtered MoSx films have been reportedly improved by inert gas ion implantation. We tried to extend their wear life by introducing indium, carbon and gallium ion implantation. Pin-on-disk testers were used to measure friction coefficient and wear life in a vacuum, dry and humid air. Comparing with the unimplanted films, we found that the indium ion implanted films showed marked improvement in wear life in a vacuum. Carbon ion implanted films showed improvement in wear life in high humid air. Implantation was effective when it was conducted with maximum concentration at the interface between film and substrate rather than at the neighborhood of the interface inside a film. (author)

InP (Indium Phosphide): Into the future

International Nuclear Information System (INIS)

Brandhorst, H.W. Jr.

1989-03-01

Major industry is beginning to be devoted to indium phosphide and its potential applications. Key to these applications are high speed and radiation tolerance; however the high cost of indium phosphide may be an inhibitor to progress. The broad applicability of indium phosphide to many devices will be discussed with an emphasis on photovoltaics. Major attention is devoted to radiation tolerance and means of reducing cost of devices. Some of the approaches applicable to solar cells may also be relevant to other devices. The intent is to display the impact of visionary leadership in the field and enable the directions and broad applicability of indium phosphide

InP (Indium Phosphide): Into the future

Science.gov (United States)

Brandhorst, Henry W., Jr.

1989-01-01

Major industry is beginning to be devoted to indium phosphide and its potential applications. Key to these applications are high speed and radiation tolerance; however the high cost of indium phosphide may be an inhibitor to progress. The broad applicability of indium phosphide to many devices will be discussed with an emphasis on photovoltaics. Major attention is devoted to radiation tolerance and means of reducing cost of devices. Some of the approaches applicable to solar cells may also be relevant to other devices. The intent is to display the impact of visionary leadership in the field and enable the directions and broad applicability of indium phosphide.

Fabrication of Amorphous Indium Gallium Zinc Oxide Thin Film Transistor by using Focused Ion Beam

Science.gov (United States)

Zhu, Wencong

Compared with other transparent semiconductors, amorphous indium gallium zinc oxide (a-IGZO) has both good uniformity and high electron mobility, which make it as a good candidate for displays or large-scale transparent circuit. The goal of this research is to fabricate alpha-IGZO thin film transistor (TFT) with channel milled by focused ion beam (FIB). TFTs with different channel geometries can be achieved by applying different milling strategies, which facilitate modifying complex circuit. Technology Computer-Aided Design (TCAD) was also introduced to understand the effect of trapped charges on the device performance. The investigation of the trapped charge at IGZO/SiO2 interface was performed on the IGZO TFT on p-Silicon substrate with thermally grown SiO2 as dielectric. The subgap density-of-state model was used for the simulation, which includes conduction band-tail trap states and donor-like state in the subgap. The result shows that the de-trapping and donor-state ionization determine the interface trapped charge density at various gate biases. Simulation of IGZO TFT with FIB defined channel on the same substrate was also applied. The drain and source were connected intentionally during metal deposition and separated by FIB milling. Based on the simulation, the Ga ions in SiO2 introduced by the ion beam was drifted by gate bias and affects the saturation drain current. Both side channel and direct channel transparent IGZO TFTs were fabricated on the glass substrate with coated ITO. Higher ion energy (30 keV) was used to etch through the substrate between drain and source and form side channels at the corner of milled trench. Lower ion energy (16 keV) was applied to stop the milling inside IGZO thin film and direct channel between drain and source was created. Annealing after FIB milling removed the residual Ga ions and the devices show switch feature. Direct channel shows higher saturation drain current (~10-6 A) compared with side channel (~10-7 A) because

Use of and occupational exposure to indium in the United States.

Science.gov (United States)

Hines, Cynthia J; Roberts, Jennifer L; Andrews, Ronnee N; Jackson, Matthew V; Deddens, James A

2013-01-01

Indium use has increased greatly in the past decade in parallel with the growth of flat-panel displays, touchscreens, optoelectronic devices, and photovoltaic cells. Much of this growth has been in the use of indium tin oxide (ITO). This increased use has resulted in more frequent and intense exposure of workers to indium. Starting with case reports and followed by epidemiological studies, exposure to ITO has been linked to serious and sometimes fatal lung disease in workers. Much of this research was conducted in facilities that process sintered ITO, including manufacture, grinding, and indium reclamation from waste material. Little has been known about indium exposure to workers in downstream applications. In 2009-2011, the National Institute for Occupational Safety and Health (NIOSH) contacted 89 potential indium-using companies; 65 (73%) responded, and 43 of the 65 responders used an indium material. Our objective was to identify current workplace applications of indium materials, tasks with potential indium exposure, and exposure controls being used. Air sampling for indium was either conducted by NIOSH or companies provided their data for a total of 63 air samples (41 personal, 22 area) across 10 companies. Indium exposure exceeded the NIOSH recommended exposure limit (REL) of 0.1 mg/m(3) for certain methods of resurfacing ITO sputter targets, cleaning sputter chamber interiors, and in manufacturing some inorganic indium compounds. Indium air concentrations were low in sputter target bonding with indium solder, backside thinning and polishing of fabricated indium phosphide-based semiconductor devices, metal alloy production, and in making indium-based solder pastes. Exposure controls such as containment, local exhaust ventilation (LEV), and tool-mounted LEV can be effective at reducing exposure. In conclusion, occupational hygienists should be aware that the manufacture and use of indium materials can result in indium air concentrations that exceed the NIOSH

Selectivity in extraction of copper and indium with chelate extractants

International Nuclear Information System (INIS)

Zivkovic, D.

2003-01-01

Simultaneous extraction of copper and indium with chelate extractants (LIX84 and D2E11PA) was described. Stechiometry of metal-organic complexes examined using the method of equimolar ratios resulted in CuR 2 and InR 3 forms of hydrophobic extracting species. A linear correlation was obtained between logarithm of distribution coefficients and chelate agents and pH, respectively. Selectivity is generally higher with higher concentrations of chelate agents in the organic phase, and is decreased with increase of concentration of hydrogen ions in feeding phase. (Original)

Review of pulmonary toxicity of indium compounds to animals and humans

International Nuclear Information System (INIS)

Tanaka, Akiyo; Hirata, Miyuki; Kiyohara, Yutaka; Nakano, Makiko; Omae, Kazuyuki; Shiratani, Masaharu; Koga, Kazunori

2010-01-01

Due to the increased production of ITO, the potential health hazards arising from occupational exposure to this material have attracted much attention. This review consists of three parts: 1) toxic effects of indium compounds on animals, 2) toxic effects of indium compounds on humans, and 3) recommendations for preventing exposure to indium compounds in the workplace. Available data have indicated that insoluble form of indium compounds, such as ITO, indium arsenide (InAs) and indium phosphide (InP), can be toxic to animals. Furthermore, InP has demonstrated clear evidence of carcinogenic potential in long-term inhalation studies using experimental animals. As for the dangers to humans, some data are available concerning adverse health effects to workers who have been exposed to indium-containing particles. The Japan Society for Occupational Health recommended the value of 3 μg/L of indium in serum as the occupational exposure limit based on biological monitoring to preventing adverse health effects in workers resulting from occupational exposure to indium compounds. Accordingly, it is essential that much greater attention is focused on human exposure to indium compounds, and precautions against possible exposure to indium compounds are most important with regard to health management among indium-handling workers.

Indium-111 octreotide uptake in the surgical scar

Energy Technology Data Exchange (ETDEWEB)

Degirmenci, B.; Bekis, R.; Durak, H.; Derebeck, E. [Dokuz Eylul Univ., Izmir (Turkey). Dept. of Nuclear Medicine; Sen, M. [Dokuz Eylul Univ., Izmir (Turkey). Dept. of Radiation Oncology

1999-07-01

Indium-111 octreotide uptake has been reported in various somatostatin receptor positive tumors, granulomas and autoimmune diseases in which activated leucocytes may play a role, subcutaneous cavernous hemangioma and angiofibroma. We present Indium-111 octreotide uptake in a surgical abdominal scar tissue 1.5 to 6 months after surgery in a patient who had been treated for recurrent carcinoid tumor in the rectosigmoid junction. Indium-111 octreotide uptake in a surgical scar may be related to the binding to somatostatin receptors in the activated lymphocytes and fibroblasts that is previously reported. (orig.) [German] In verschiedenen Somatostatinrezeptor-positiven Tumoren, Granulomen, bei Autoimmunerkrankungen, in denen aktivierte Leukozyten eine Rolle spielen, subcutanen kavernoesen Hammangiomen und Angiofibromen wurde ueber die Anreicherung von Indium-111-Oktreotid berichtet. Wir berichten ueber die Anreicherung von Indium-111-Oktreotid in einer chirurgischen Narbe ueber dem Abdomen nach 1,5 und 6 Monaten bei einem Patienten mit einem Rezidiv-Karzinoid im rektosigmoidalen Uebergang. Die Anreicherung von Indium-111-Oktreotid in chirurgischen Narbengewebe koennte in Zusammenhang stehen mit einer Bindung an Somatostationrezeptoren in aktivierten Lymphozyten und Fibroblasten, ueber die schon berichtet wurde. (orig.)

Cross-current leaching of indium from end-of-life LCD panels

Energy Technology Data Exchange (ETDEWEB)

Rocchetti, Laura; Amato, Alessia; Fonti, Viviana [Department of Life and Environmental Sciences, Università Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy); Ubaldini, Stefano [Institute of Environmental Geology and Geoengineering IGAG, National Research Council, Via Salaria km 29300, 00015 Montelibretti, Rome (Italy); De Michelis, Ida [Department of Industrial Engineering, Information and Economy, University of L’Aquila, Via Giovanni Gronchi 18, 67100, Zona industriale di Pile, L’Aquila (Italy); Kopacek, Bernd [ISL Kopacek KG, Beckmanngasse 51, 1140 Wien (Austria); Vegliò, Francesco [Department of Industrial Engineering, Information and Economy, University of L’Aquila, Via Giovanni Gronchi 18, 67100, Zona industriale di Pile, L’Aquila (Italy); Beolchini, Francesca, E-mail: f.beolchini@univpm.it [Department of Life and Environmental Sciences, Università Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy)

2015-08-15

Graphical abstract: Display Omitted - Highlights: • End-of-life LCD panels represent a source of indium. • Several experimental conditions for indium leaching have been assessed. • Indium is completely extracted with 2 M sulfuric acid at 80 °C for 10 min. • Cross-current leaching improves indium extraction and operating costs are lowered. • Benefits to the environment come from reduction of CO{sub 2} emissions and reagents use. - Abstract: Indium is a critical element mainly produced as a by-product of zinc mining, and it is largely used in the production process of liquid crystal display (LCD) panels. End-of-life LCDs represent a possible source of indium in the field of urban mining. In the present paper, we apply, for the first time, cross-current leaching to mobilize indium from end-of-life LCD panels. We carried out a series of treatments to leach indium. The best leaching conditions for indium were 2 M sulfuric acid at 80 °C for 10 min, which allowed us to completely mobilize indium. Taking into account the low content of indium in end-of-life LCDs, of about 100 ppm, a single step of leaching is not cost-effective. We tested 6 steps of cross-current leaching: in the first step indium leaching was complete, whereas in the second step it was in the range of 85–90%, and with 6 steps it was about 50–55%. Indium concentration in the leachate was about 35 mg/L after the first step of leaching, almost 2-fold at the second step and about 3-fold at the fifth step. Then, we hypothesized to scale up the process of cross-current leaching up to 10 steps, followed by cementation with zinc to recover indium. In this simulation, the process of indium recovery was advantageous from an economic and environmental point of view. Indeed, cross-current leaching allowed to concentrate indium, save reagents, and reduce the emission of CO{sub 2} (with 10 steps we assessed that the emission of about 90 kg CO{sub 2}-Eq. could be avoided) thanks to the recovery of indium

Indium-oxide nanoparticles for RRAM devices compatible with CMOS back-end-off-line

Science.gov (United States)

León Pérez, Edgar A. A.; Guenery, Pierre-Vincent; Abouzaid, Oumaïma; Ayadi, Khaled; Brottet, Solène; Moeyaert, Jérémy; Labau, Sébastien; Baron, Thierry; Blanchard, Nicholas; Baboux, Nicolas; Militaru, Liviu; Souifi, Abdelkader

2018-05-01

We report on the fabrication and characterization of Resistive Random Access Memory (RRAM) devices based on nanoparticles in MIM structures. Our approach is based on the use of indium oxide (In2O3) nanoparticles embedded in a dielectric matrix using CMOS-full-compatible fabrication processes in view of back-end-off-line integration for non-volatile memory (NVM) applications. A bipolar switching behavior has been observed using current-voltage measurements (I-V) for all devices. Very high ION/IOFF ratios have been obtained up to 108. Our results provide insights for further integration of In2O3 nanoparticles-based devices for NVM applications. He is currently a Postdoctoral Researcher in the Institute of Nanotechnologies of Lyon (INL), INSA de Lyon, France, in the Electronics Department. His current research include indium oxide nanoparticles for non-volatile memory applications, and the integrations of these devices in CMOS BEOL.

Fabrication, structure and mechanical properties of indium nanopillars

Energy Technology Data Exchange (ETDEWEB)

Lee, Gyuhyon; Kim, Ju-Young; Budiman, Arief Suriadi; Tamura, Nobumichi; Kunz, Martin; Chen, Kai; Burek, Michael J.; Greer, Julia R.; Tsui, Ting Y.

2010-01-01

Solid and hollow cylindrical indium pillars with nanoscale diameters were prepared using electron beam lithography followed by the electroplating fabrication method. The microstructure of the solid-core indium pillars was characterized by scanning micro-X-ray diffraction, which shows that the indium pillars were annealed at room temperature with very few dislocations remaining in the samples. The mechanical properties of the solid pillars were characterized using a uniaxial microcompression technique, which demonstrated that the engineering yield stress is {approx}9 times greater than bulk and is {approx}1/28 of the indium shear modulus, suggesting that the attained stresses are close to theoretical strength. Microcompression of hollow indium nanopillars showed evidence of brittle fracture. This may suggest that the failure mode for one of the most ductile metals can become brittle when the feature size is sufficiently small.

Indium Doped Zinc Oxide Thin Films Deposited by Ultrasonic Chemical Spray Technique, Starting from Zinc Acetylacetonate and Indium Chloride

Directory of Open Access Journals (Sweden)

Rajesh Biswal

2014-07-01

Full Text Available The physical characteristics of ultrasonically sprayed indium-doped zinc oxide (ZnO:In thin films, with electrical resistivity as low as 3.42 × 10−3 Ω·cm and high optical transmittance, in the visible range, of 50%–70% is presented. Zinc acetylacetonate and indium chloride were used as the organometallic zinc precursor and the doping source, respectively, achieving ZnO:In thin films with growth rate in the order of 100 nm/min. The effects of both indium concentration and the substrate temperature on the structural, morphological, optical, and electrical characteristics were measured. All the films were polycrystalline, fitting well with hexagonal wurtzite type ZnO. A switching in preferential growth, from (002 to (101 planes for indium doped samples were observed. The surface morphology of the films showed a change from hexagonal slices to triangle shaped grains as the indium concentration increases. Potential applications as transparent conductive electrodes based on the resulting low electrical resistance and high optical transparency of the studied samples are considered.

Indium solar neutrino experiment using superconducting grains

International Nuclear Information System (INIS)

Bellefon, A. de; Espigat, P.

1984-08-01

In this paper we would like to emphasize the revival of interest for Indium experiment in Europe. Properties of metastable superconducting indium grains are presented and our progress towards making an experiment feasible is reviewed

Cross-current leaching of indium from end-of-life LCD panels.

Science.gov (United States)

Rocchetti, Laura; Amato, Alessia; Fonti, Viviana; Ubaldini, Stefano; De Michelis, Ida; Kopacek, Bernd; Vegliò, Francesco; Beolchini, Francesca

2015-08-01

Indium is a critical element mainly produced as a by-product of zinc mining, and it is largely used in the production process of liquid crystal display (LCD) panels. End-of-life LCDs represent a possible source of indium in the field of urban mining. In the present paper, we apply, for the first time, cross-current leaching to mobilize indium from end-of-life LCD panels. We carried out a series of treatments to leach indium. The best leaching conditions for indium were 2M sulfuric acid at 80°C for 10min, which allowed us to completely mobilize indium. Taking into account the low content of indium in end-of-life LCDs, of about 100ppm, a single step of leaching is not cost-effective. We tested 6 steps of cross-current leaching: in the first step indium leaching was complete, whereas in the second step it was in the range of 85-90%, and with 6 steps it was about 50-55%. Indium concentration in the leachate was about 35mg/L after the first step of leaching, almost 2-fold at the second step and about 3-fold at the fifth step. Then, we hypothesized to scale up the process of cross-current leaching up to 10 steps, followed by cementation with zinc to recover indium. In this simulation, the process of indium recovery was advantageous from an economic and environmental point of view. Indeed, cross-current leaching allowed to concentrate indium, save reagents, and reduce the emission of CO2 (with 10 steps we assessed that the emission of about 90kg CO2-Eq. could be avoided) thanks to the recovery of indium. This new strategy represents a useful approach for secondary production of indium from waste LCD panels. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mn-implanted, polycrystalline indium tin oxide and indium oxide films

International Nuclear Information System (INIS)

Scarlat, Camelia; Vinnichenko, Mykola; Xu Qingyu; Buerger, Danilo; Zhou Shengqiang; Kolitsch, Andreas; Grenzer, Joerg; Helm, Manfred; Schmidt, Heidemarie

2009-01-01

Polycrystalline conducting, ca. 250 nm thick indium tin oxide (ITO) and indium oxide (IO) films grown on SiO 2 /Si substrates using reactive magnetron sputtering, have been implanted with 1 and 5 at.% of Mn, followed by annealing in nitrogen or in vacuum. The effect of the post-growth treatment on the structural, electrical, magnetic, and optical properties has been studied. The roughness of implanted films ranges between 3 and 15 nm and XRD measurements revealed a polycrystalline structure. A positive MR has been observed for Mn-implanted and post-annealed ITO and IO films. It has been interpreted by considering s-d exchange. Spectroscopic ellipsometry has been used to prove the existence of midgap electronic states in the Mn-implanted ITO and IO films reducing the transmittance below 80%.

How metallic is the binding state of indium hosted by excess-metal chalcogenides in ore deposits?

Science.gov (United States)

Ondina Figueiredo, Maria; Pena Silva, Teresa; Oliveira, Daniel; Rosa, Diogo

2010-05-01

Discovered in 1863, indium is nowadays a strategic scarce metal used both in classical technologic fields (like low melting-temperature alloys and solders) and in innovative nano-technologies to produce "high-tech devices" by means of new materials, namely liquid crystal displays (LCDs), organic light emitting diodes (OLEDs) and the recently introduced transparent flexible thin-films manufactured with ionic amorphous oxide semiconductors (IAOS). Indium is a typical chalcophile element, seldom forming specific minerals and occurring mainly dispersed within polymetallic sulphides, particularly with excess metal ions [1]. The average content of indium in the Earth's crust is very low but a further increase in its demand is still expected in the next years, thus focusing a special interest in uncovering new exploitation sites through promising polymetallic sulphide ores - e.g., the Iberian Pyrite Belt (IPB) [2] - and in improving recycling technologies. Indium recovery stands mostly on zinc extraction from sphalerite, the natural cubic sulphide which is the prototype of so-called "tetrahedral sulphides" where metal ions fill half of the available tetrahedral sites within the cubic closest packing of sulphur anions where the double of unfilled interstices are available for further in-filling. It is worth remarking that such packing array is particularly suitable for accommodating polymetallic cations by filling closely located interstitial sites [3] as happens in excess-metal tetrahedral sulphides - e.g. bornite, ideally Cu5FeS4, recognized as an In-carrying mineral [4]. Studying the tendency towards In-In interactions able of leading to the formation of polycations would efficiently contribute to understand indium crystal chemistry and the metal binding state in natural chalcogenides. Accordingly, an X-ray absorption near-edge spectroscopy (XANES) study at In L3-edge was undertaken using the instrumental set-up of ID21 beamline at the ESRF (European Synchrotron

Indium oxide/n-silicon heterojunction solar cells

Science.gov (United States)

Feng, Tom; Ghosh, Amal K.

1982-12-28

A high photo-conversion efficiency indium oxide/n-silicon heterojunction solar cell is spray deposited from a solution containing indium trichloride. The solar cell exhibits an Air Mass One solar conversion efficiency in excess of about 10%.

Silver-indium-cadmium control rod behavior and aerosol formation in severe reactor accidents

International Nuclear Information System (INIS)

Petti, D.A.

1987-04-01

Silver-indium-cadmium (Ag-In-Cd) control rod behavior and aerosol formation in severe reactor accidents are examined in an attempt to improve the methodology used to estimate reactor accident source terms. Control rod behavior in both in-pile and out-of-pile experiments is reviewed. A mechanistic model named VAPOR is developed that calculates the downward relocation and simultaneous vaporization behavior of the Ag-In-Cd alloy expected after control rod failure in a severe reactor accident. VAPOR is used to predict the release of silver, indium, and cadmium vapors expected in the Power Burst Facility (PBF) Severe Fuel Damage (SFD) 1-4 experiment. In addition, a sensitivity study is performed. Although cadmium is found to be the most volatile constituent of the alloy, all of the calculations predict that the rapid relocation of the alloy down to cooler portions of the core results in a small release for all three control rod alloy vapors. Potential aerosol formation mechanisms in a severe reactor accident are reviewed. Specifically, models for homogeneous, ion-induced, and heterogeneous nucleation are investigated. These models are applied to silver, cadmium, and CsI to examine the nucleation behavior of these three potential aerosol sources in a severe reactor accident and to illustrate the competition among these mechanisms for vapor depletion. The results indicate that aerosol formation in a severe reactor accident occurs in three stages. In the first stage, ion-induced nucleation causes aerosol generation. During the second stage, ion-induced and heterogeneous nucleation operates as competing pathways for gas-to-particle conversion until sufficient aerosol surface area is generated. In the third stage, ion-induced nucleation ceases; and heterogeneous nucleation becomes the dominant mechanism of gas-to-particle conversion until equilibrium is reached

Indium-granulocyte scanning in the painful prosthetic joint

International Nuclear Information System (INIS)

Pring, D.J.; Henderson, R.G.; Keshavarzian, A.; Rivett, A.G.; Krausz, T.; Coombs, R.R.; Lavender, J.P.

1986-01-01

The value of indium-111-labeled granulocyte scanning to determine the presence of infection was assessed in 50 prosthetic joints (41 of which were painful) in 40 patients. Granulocytes were obtained from the patients' blood and labeled in plasma with indium 111 tropolonate. Abnormal accumulation of indium 111 in the region of the prosthesis was noted. Proven infection occurred in 11 prostheses, and all of the infections were detected by indium-111-labeled granulocyte scanning. Nineteen were not infected (including nine asymptomatic controls) and only two produced false-positive scans. This represents a specificity of 89.5%, sensitivity of 100%, and overall accuracy of 93.2%. These results compare favorably with plain radiography. There was no radiologic evidence of infection in three of the infected prostheses, and 10 of the noninfected prostheses had some radiologic features that suggested sepsis. We conclude that indium-granulocyte scanning can reliably detect or exclude infection in painful prosthetic joints and should prove useful in clinical management

A lattice-gas model of the ion current across the solid interface: fast-ion conductor - intercalate

International Nuclear Information System (INIS)

Nachev, I.; Balkanski, M.

1994-12-01

The transport of Lithium ions across the material interface: fast-ion conducting glass - intercalate is simulated by a non-trivial lattice-gas model. The model takes explicitly into account the influence of the Coulomb correlations, the site-blocking effect and the boundary conditions on the ion kinetics. Potential device applications of the model are pointed out by computing the current density of Lithium ions for material parameters of the real interface: doped ternary borate glass - Indium Selenide, which constitute the electrolyte and the cathode, respectively, of a thin-film microbattery with improved performance. (author). 10 refs, 4 figs

Looking Down Under for a Circular Economy of Indium.

Science.gov (United States)

Werner, Tim T; Ciacci, Luca; Mudd, Gavin Mark; Reck, Barbara K; Northey, Stephen Alan

2018-02-20

Indium is a specialty metal crucial for modern technology, yet it is potentially critical due to its byproduct status in mining. Measures to reduce its criticality typically focus on improving its recycling efficiency at end-of-life. This study quantifies primary and secondary indium resources ("stocks") for Australia through a dynamic material-flow analysis. It is based on detailed assessments of indium mineral resources hosted in lead-zinc and copper deposits, respective mining activities from 1844 to 2013, and the trade of indium-containing products from 1988 to 2015. The results show that Australia's indium stocks are substantial, estimated at 46.2 kt in mineral resources and an additional 14.7 kt in mine wastes. Australian mineral resources alone could meet global demand (∼0.8 kt/year) for more than five decades. Discarded material from post-consumer products, instead, is negligible (43 t). This suggests that the resilience of Australia's indium supply can best be increased through efficiency gains in mining (such as introducing domestic indium refining capacity) rather than at the end of the product life. These findings likely also apply to other specialty metals, such as gallium or germanium, and other resource-dominated countries. Finally, the results illustrate that national circular economy strategies can differ substantially.

Work function of oxygen exposed lead and lead/indium alloy films

International Nuclear Information System (INIS)

Gundlach, K.H.; Hellemann, H.P.; Hoelzl, J.

1982-01-01

The effect of indium in superconducting tunnel junctions with lead/indium alloy base electrodes is investigated by measuring the vacuum work function of lead, indium, and lead/indium alloy films. It is found that the anomalous decrease of the work function of lead upon exposure to oxygen, explained by the penetration of oxygen into the inner surface of the lead film, is reversed into a slight increase in work function when some indium is added to the lead. This result indicates that the addition of indium provides a protection by suppressing the penetration of oxygen (and probably other gases) into the interior of the thin film

Secondary indium production from end-of-life liquid crystal displays

Energy Technology Data Exchange (ETDEWEB)

Amato, Alessia; Rocchetti, Laura; Fonti, Viviana; Ruello, Maria Letizia; Beolchini, Francesca [Universita Politecnica of Marche, DISVA, Via Brecce Bianche, 60131 Ancona (Italy)

2016-12-15

In 2014, the European Union identified 20 raw materials critical for economic importance and high supply risk. Indium, used in several innovative technologies, is among such critical raw materials. Generally, it is mined as a by-product of zinc from a mineral named sphalerite, with a concentration between 1 and 100 ppm. Currently, the largest producer of indium is China and about 84% of the worldwide indium consumption is used for liquid crystal display (LCD) production, in particular to form an indium-tin-oxide (ITO) film with transparent conductor properties. The fast evolution of LCD technologies caused a double effect: the growth of indium demand and an increase of waste electrical and electronic equipment (WEEE). Considering these two factors, the aim of this study is to make the end-of-life LCDs a secondary indium resource. With this purpose, an indium recovery process was developed carrying out an acidic leaching, followed by a zinc cementation. The first step allowed a complete indium extraction using 2M sulfuric acid at 80 C for 10 min. The problem of low indium concentration in the scraps (around 150 ppm) was overcome using a cross-current configuration in the leaching phase that allowed an increase of metal concentration and a decrease of reagents consumption. An indium recovery higher than 90% was obtained in the final cementation step, using 5 g/L of zinc powder at pH 3 and 55 C for 10 min. Considering its high efficiency, this process is promising in a context of circular economy, where a waste becomes a resource. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effects of a powered air-purifying respirator intervention on indium exposure reduction and indium related biomarkers among ITO sputter target manufacturing workers.

Science.gov (United States)

Liu, Hung-Hsin; Chen, Chang-Yuh; Lan, Cheng-Hang; Chang, Cheng-Ping; Peng, Chiung-Yu

2016-01-01

This study aimed to evaluate the efficacy of powered air-purifying respirators (PAPRs) worn by the workers, and to investigate the effect of this application on exposure and preclinical effects in terms of workplace measuring and biomarker monitoring in ITO sputter target manufacturing plants and workers, respectively. Fifty-four workers were recruited and investigated from 2010-2012, during which PAPRs were provided to on-site workers in September 2011. Each worker completed questionnaires and provided blood and urine samples for analysis of biomarkers of indium exposure and preclinical effects. Area and personal indium air samples were randomly collected from selected worksites and from participants. The penetration percentage of the respirator (concentration inside respirator divided by concentration outside respirator) was 6.6%. Some biomarkers, such as S-In, SOD, GPx, GST, MDA, and TMOM, reflected the decrease in exposure and showed lower levels, after implementation of PAPRs. This study is the first to investigate the efficacy of PAPRs for reducing indium exposure. The measurement results clearly showed that the implementation of PAPRs reduces levels of indium-related biomarkers. These findings have practical applications for minimizing occupational exposure to indium and for managing the health of workers exposed to indium.

Light forces on an indium atonic beam; Lichtkraefte auf einen Indiumatomstrahl

Energy Technology Data Exchange (ETDEWEB)

Kloeter, B.

2007-07-01

In this thesis it was studied, whether indium is a possible candidate for the nanostructuration respectively atomic lithography. For this known method for the generation and stabilization of the light necessary for the laser cooling had to be fitted to the special properties of indium. The spectroscopy of indium with the 451 nm and the 410 nm light yielded first hints that the formulae for the atom-light interaction for a two-level atom cannot be directly transferred to the indium atom. By means of the obtained parameters of the present experiment predictions for a possible Doppler cooling of the indium atomic beam were calculated. Furthermore the possibility for the direct deposition of indium on a substrate was studied.

Flexible inverted polymer solar cells with an indium-free tri-layer cathode

International Nuclear Information System (INIS)

El Hajj, Ahmad; Lucas, Bruno; Schirr-Bonnans, Martin; Ratier, Bernard; Kraft, Thomas M.; Torchio, Philippe

2014-01-01

Indium tin oxide (ITO)-free inverted polymer solar cells (PSCs) have been fabricated without the need of an additional electron transport layer. The indium-free transparent electrode consists of a tri-layer stack ZnO (30 nm)/Ag (14 nm)/ZnO (30 nm) deposited on glass and plastic substrates via ion-beam sputtering. The tri-layer electrodes exhibit similar physical properties to its ITO counterpart, specifically yielding high transmittance and low resistivity (76.5% T at 550 nm, R sq of 8 Ω/◻) on plastic substrates. The novel tri-layer electrode allows for the fabrication of inverted PSCs without the additional ZnO interfacial layer commonly deposited between ITO and the photoactive layer. This allows for the preparation of thinner plastic solar cells using less material than conventional architectures. Initial studies involving the newly realized architecture (tri-layer electrode/P3HT:PCBM/PEDOT:PSS/Ag) have shown great promise for the transition from ITO to other viable electrodes in organic electronics

TEM EDS analysis of epitaxially-grown self-assembled indium islands

Directory of Open Access Journals (Sweden)

Jasmine Sears

2017-05-01

Full Text Available Epitaxially-grown self-assembled indium nanostructures, or islands, show promise as nanoantennas. The elemental composition and internal structure of indium islands grown on gallium arsenide are explored using Transmission Electron Microscopy (TEM Energy Dispersive Spectroscopy (EDS. Several sizes of islands are examined, with larger islands exhibiting high (>94% average indium purity and smaller islands containing inhomogeneous gallium and arsenic contamination. These results enable more accurate predictions of indium nanoantenna behavior as a function of growth parameters.

Polarographic determination of selenium in indium

International Nuclear Information System (INIS)

Kaplan, B.Ya.; Mikheeva, V.A.; Priz, N.B.

1978-01-01

The procedure of determining nx10 -6 % Se in indium after concentrating in an elemental form on arsenic and sulphur has been developed. The selenium content is determined by inversion a.c. polarography on a sulphuric-acid background in the presence of Cu(2), potassium bichromate, and sodium pyrophosphate. 5.7x10 -6 % Se in metal indium has been determined by this procedure, the mean standard deviation being Sr=0.26

Hydrogen Production via Steam Reforming of Ethyl Alcohol over Palladium/Indium Oxide Catalyst

Directory of Open Access Journals (Sweden)

Tetsuo Umegaki

2009-01-01

Full Text Available We report the synergetic effect between palladium and indium oxide on hydrogen production in the steam reforming reaction of ethyl alcohol. The palladium/indium oxide catalyst shows higher hydrogen production rate than indium oxide and palladium. Palladium/indium oxide affords ketonization of ethyl alcohol with negligible by-product carbon monoxide, while indium oxide mainly affords dehydration of ethyl alcohol, and palladium affords decomposition of ethyl alcohol with large amount of by-product carbon monoxide. The catalytic feature of palladium/indium oxide can be ascribed to the formation of palladium-indium intermetallic component during the reaction as confirmed by X-ray diffraction and X-ray photoelectron spectroscopic measurements.

Synthesis and characterization ligand tris-(2-thiosalicylamidoethyl)amine and its iron complexes and indium

International Nuclear Information System (INIS)

Guerra-Garcia, Pedro Pablo; Valle Bourrouet, Grettel

2006-01-01

The synthesis of coordination chemistry ligand tris-(2-tiosalicilamidoetil)amine is presented within the framework of study of tripod ligands, the corresponding complexes of iron and indium. Also, its spectroscopic characterization by proton magnetic resonance is showed; so the influence of ligand on a redox active metal and an inactive is compared. Electrochemical methods have been used. The presence of sulfur atoms modifies the redox and magnetic behavior of iron ion (III), as has been found in other similar ligands [es

Catalytic property of an indium-deposited powder-type material containing silicon and its dependence on the dose of indium nano-particles irradiated by a pulse arc plasma process

Directory of Open Access Journals (Sweden)

Satoru Yoshimura

2017-06-01

Full Text Available Indium nano-particle irradiations onto zeolite powders were carried out using a pulse arc plasma source system. X-ray photoelectron spectroscopic and scanning electron microscopic studies of an indium irradiated zeolite sample revealed that indium nano-particles were successfully deposited on the sample. Besides, the sample was found to be capable of catalyzing an organic chemical reaction (i.e., Friedel-Crafts alkylation. Then, we examined whether or not the catalytic ability depends on the irradiated indium dose, having established the optimal indium dose for inducing the catalytic effect.

Preparation of Indium Pentetate Complex (111 In-DTPA)

International Nuclear Information System (INIS)

Shahhosseini, S.; Farshidfar, G.R.; Najafi, R.

2000-01-01

There is no organometallic compound of Indium know to exist naturally in the human body. However, a number of compounds prepared with 111 In have been evaluated for localization studies. The useful radioactive decay characteristics and the suitable chemical properties of the metal ion have drawn attention of many investigators resulting in the preparation of numerous 111 In labeled compounds for potential medical applications. One of them is 111 In-DTPA complex that is used for cerebral spinal fluid studies. In the present study, DTPA has been chelated with 111 In by employing various methods and then tested for its stability in vitro during storage and in human plasma. Three methods for the preparation of 11 1In-DTPA were used. In every method, labeling efficiency and radiochemical purity were determined by chromatography systems

Neutral complexes of the indium dihalides

Energy Technology Data Exchange (ETDEWEB)

Sinclair, I.; Worrall, I.J. (Lancaster Univ. (UK))

1982-03-15

The neutral complexes In/sub 2/X/sub 4/.2L (X=Cl, Br, I; L 1,4-dioxan, tetrahydropyran, tetrahydrofuran, tetrahydrothiophene), In/sub 2/X/sub 4/.2L (X=Br, I; Ldimethylsulphide), In/sub 2/X/sub 4/.4L (X=Cl, Br, I; Lpiperidine, piperazine, morpholine), and In/sub 2/X/sub 4/.4L (X=Br, I; L=pyridine, dimethylsulphoxide) have been prepared. Solid state Raman spectra indicate that the compounds contain indium-indium bonds.

Theoretical Study of Indium Compounds of Interest for Organometallic Chemical Vapor Deposition

Science.gov (United States)

Cardelino, B. H.; Moore, C. E.; Cardelino, C. A.; Frazier, D. O.; Backmann, K. J.

2000-01-01

The structural. electronic and therinochemical properties of indium compounds which are of interest in halide transport and organometallic chemical vapor deposition processes have been studied by ab initio and statistical mechanics methods. The compounds reported include: indium halides and hydrides (InF, InCl, InCl3, InH, InH2, InH3); indium clusters (In2, In3); methylindium, dimethylindium, and their hydrogen derivatives [In(CH3), In(CH3)H, In(CH3)H2, In(CH3)2, In(CH3)2H]; dimethyl-indium dimer [In2(CH3)4], trimethyl-indium [In(CH3)3]; dehydrogenated methyl, dimethyl and trimethylindium [In(CH3)2CH2, In(CH3)CH2, In(CH2)], trimethylindium adducts with ammonia, trimethylamine and hydrazine [(CH3)3In:NH3, (CH3)3In:N(CH3)3, (CH3)3In:N(H2)N(H2)]; dimethylamino-indium and methylimino-indium [In(CH3)2(NH2), In(CH3)(NH)]; indium nitride and indium nitride dimer (InN, In2N2), indium phosphide, arsenide and antimonide ([InP, InAs, InSb). The predicted electronic properties are based on density functional theory calculations; the calculated thermodynamic properties are reported following the format of the JANAF (Joint Army, Navy, NASA, Air Force) Tables. Equilibrium compositions at two temperatures (298 and 1000 K) have been analyzed for groups of competing simultaneous reactions.

Synthesis and photophysical properties of indium(III) phthalocyanine derivatives

Energy Technology Data Exchange (ETDEWEB)

Özceşmeci, İbrahim, E-mail: ozcesmecii@itu.edu.tr [Department of Chemistry, Technical University of Istanbul, Maslak 34469, Istanbul (Turkey); Gelir, Ali [Department of Physics, Technical University of Istanbul, Maslak 34469, Istanbul (Turkey); Gül, Ahmet [Department of Chemistry, Technical University of Istanbul, Maslak 34469, Istanbul (Turkey)

2014-03-15

Three chloroindium(III) phthalocyanine derivatives bearing four aromatic (naphthalene or pyrene) or aliphatic (hexylthio) groups were prepared from corresponding phthalonitrile compounds. The indium(III) phthalocyanine derivatives were characterized with elemental analyses, mass, proton nuclear magnetic resonance ({sup 1}H NMR), Fourier transform infrared spectroscopy (FT-IR) and ultraviolet–visible spectroscopy (UV–vis) techniques. Quantum yields and the energy transfer from the substituents to phthalocyanine core were examined. No energy transfer was observed for 5. The energy transfer efficiency from pyrene units to indium phthalocyanine core was calculated as 0.27 for 6. Quantum yields of all samples were very small due to heavy atom effect of indium atom in the core. It was also observed that upon binding of pyrene and naphthalene units to indium phthalocyanine as substituents, the quantum yields of indium phthalocyanine parts of 5 and 6 decreased. -- Highlights: • Three chloroindium(III) phthalocyanines were prepared and characterized. • Aggregation properties of these compounds were investigated. • The energy transfer efficiency was examined. • Quantum yield of these systems were calculated.

An advanced case of indium lung disease with progressive emphysema.

Science.gov (United States)

Nakano, Makiko; Tanaka, Akiyo; Hirata, Miyuki; Kumazoe, Hiroyuki; Wakamatsu, Kentaro; Kamada, Dan; Omae, Kazuyuki

2016-09-30

To report the occurrence of an advanced case of indium lung disease with severely progressive emphysema in an indium-exposed worker. A healthy 42-year-old male smoker was employed to primarily grind indium-tin oxide (ITO) target plates, exposing him to indium for 9 years (1998-2008). In 2004, an epidemiological study was conducted on indium-exposed workers at the factory in which he worked. The subject's serum indium concentration (In-S) was 99.7 μg/l, while his serum Krebs von den Lungen-6 level was 2,350 U/ml. Pulmonary function tests showed forced vital capacity (FVC) of 4.17 l (91.5% of the JRS predicted value), forced expiratory volume in 1 s (FEV 1 ) of 3.19 l (80.8% of predicted), and an FEV 1 -to-FVC ratio of 76.5%. A high-resolution chest computed tomography (HRCT) scan showed mild interlobular septal thickening and mild emphysematous changes. In 2008, he was transferred from the ITO grinding workplace to an inspection work section, where indium concentrations in total dusts had a range of 0.001-0.002 mg/m 3 . In 2009, the subject's In-S had increased to 132.1 μg/l, and pulmonary function tests revealed obstructive changes. In addition, HRCT scan showed clear evidence of progressive lung destruction with accompanying severe centrilobular emphysema and interlobular septal thickening in both lung fields. The subject's condition gradually worsened, and in 2015, he was registered with the Japan Organ Transplant Network for lung transplantation (LTx). Heavy indium exposure is a risk factor for emphysema, which can lead to a severity level that requires LTx as the final therapeutic option.

Electroless Formation of Hybrid Lithium Anodes for Fast Interfacial Ion Transport

KAUST Repository

Choudhury, Snehashis; Tu, Zhengyuan; Stalin, Sanjuna; Vu, Duylinh; Fawole, Kristen; Gunceler, Deniz; Sundararaman, Ravishankar; Archer, Lynden A.

2017-01-01

Rechargeable batteries based on metallic anodes are of interest for fundamental and application-focused studies of chemical and physical kinetics of liquids at solid interfaces. Approaches that allow facile creation of uniform coatings on these metals to prevent physical contact with liquid electrolytes, while enabling fast ion transport, are essential to address chemical instability of the anodes. Here, we report a simple electroless ion-exchange chemistry for creating coatings of indium on lithium. By means of joint density functional theory and interfacial characterization experiments, we show that In coatings stabilize Li by multiple processes, including exceptionally fast surface diffusion of lithium ions and high chemical resistance to liquid electrolytes. Indium coatings also undergo reversible alloying reactions with lithium ions, facilitating design of high-capacity hybrid In-Li anodes that use both alloying and plating approaches for charge storage. By means of direct visualization, we further show that the coatings enable remarkably compact and uniform electrodeposition. The resultant In-Li anodes are shown to exhibit minimal capacity fade in extended galvanostatic cycling when paired with commercial-grade cathodes.

Electroless Formation of Hybrid Lithium Anodes for Fast Interfacial Ion Transport

KAUST Repository

Choudhury, Snehashis

2017-08-17

Rechargeable batteries based on metallic anodes are of interest for fundamental and application-focused studies of chemical and physical kinetics of liquids at solid interfaces. Approaches that allow facile creation of uniform coatings on these metals to prevent physical contact with liquid electrolytes, while enabling fast ion transport, are essential to address chemical instability of the anodes. Here, we report a simple electroless ion-exchange chemistry for creating coatings of indium on lithium. By means of joint density functional theory and interfacial characterization experiments, we show that In coatings stabilize Li by multiple processes, including exceptionally fast surface diffusion of lithium ions and high chemical resistance to liquid electrolytes. Indium coatings also undergo reversible alloying reactions with lithium ions, facilitating design of high-capacity hybrid In-Li anodes that use both alloying and plating approaches for charge storage. By means of direct visualization, we further show that the coatings enable remarkably compact and uniform electrodeposition. The resultant In-Li anodes are shown to exhibit minimal capacity fade in extended galvanostatic cycling when paired with commercial-grade cathodes.

The synthesis of poly(vinylphosphonic acid-co-methacrylic acid) microbeads by suspension polymerization and the characterization of their indium adsorption properties

International Nuclear Information System (INIS)

Kwak, Noh-Seok; Baek, Youngmin; Hwang, Taek Sung

2012-01-01

Highlights: ► Microbeads were synthesized by suspension polymerization based on VPA, MAA and PEGDA. ► The best preparation condition was determined from the yield, water uptake and IEC. ► The adsorption isotherm of indium was fit to the Langmuir and Freundlich models. - Abstract: Poly(vinylphosphonic acid-co-methacrylic acid) microbeads were synthesized by suspension polymerization, and their indium adsorption properties were investigated. The obtained microbeads were characterized by Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM). The microbeads were wrinkled spheres, irrespective of the components, and their sizes ranged from 100 to 200 μm. The microbeads were thermally stable up to 260 °C. As the vinylphosphonic acid (VPA) content was increased, the synthetic yields and ion-exchange capacities decreased and the water uptakes increased. The optimum synthetic yield, ion-exchange capacity and water uptake were obtained at a 0.5 mol ratio of VPA. In addition, the maximum adsorption predicted by the Langmuir adsorption isotherm model was greatest at a 0.5 mol ratio of VPA.

The synthesis of poly(vinylphosphonic acid-co-methacrylic acid) microbeads by suspension polymerization and the characterization of their indium adsorption properties

Energy Technology Data Exchange (ETDEWEB)

Kwak, Noh-Seok; Baek, Youngmin [Department of Applied Chemistry and Biological Engineering, Chungnam National University, 79 Daehangno, Yuseong-gu, Daejeon 305-764 (Korea, Republic of); Hwang, Taek Sung, E-mail: tshwang@cnu.ac.kr [Department of Applied Chemistry and Biological Engineering, Chungnam National University, 79 Daehangno, Yuseong-gu, Daejeon 305-764 (Korea, Republic of)

2012-02-15

Highlights: Black-Right-Pointing-Pointer Microbeads were synthesized by suspension polymerization based on VPA, MAA and PEGDA. Black-Right-Pointing-Pointer The best preparation condition was determined from the yield, water uptake and IEC. Black-Right-Pointing-Pointer The adsorption isotherm of indium was fit to the Langmuir and Freundlich models. - Abstract: Poly(vinylphosphonic acid-co-methacrylic acid) microbeads were synthesized by suspension polymerization, and their indium adsorption properties were investigated. The obtained microbeads were characterized by Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM). The microbeads were wrinkled spheres, irrespective of the components, and their sizes ranged from 100 to 200 {mu}m. The microbeads were thermally stable up to 260 Degree-Sign C. As the vinylphosphonic acid (VPA) content was increased, the synthetic yields and ion-exchange capacities decreased and the water uptakes increased. The optimum synthetic yield, ion-exchange capacity and water uptake were obtained at a 0.5 mol ratio of VPA. In addition, the maximum adsorption predicted by the Langmuir adsorption isotherm model was greatest at a 0.5 mol ratio of VPA.

Process development of ITO source/drain electrode for the top-gate indium-gallium-zinc oxide transparent thin-film transistor

International Nuclear Information System (INIS)

Cheong, Woo-Seok; Yoon, Young-sun; Shin, Jae-Heon; Hwang, Chi-Sun; Chu, Hye Yong

2009-01-01

Indium-tin oxide (ITO) has been widely used as electrodes for LCDs and OLEDs. The applications are expanding to the transparent thin-film transistors (TTFT S ) for the versatile circuits or transparent displays. This paper is related with optimization of ITO source and drain electrode for TTFTs on glass substrates. For example, un-etched ITO remnants, which frequently found in the wet etching process, often originate from unsuitable ITO formation processes. In order to improve them, an ion beam deposition method is introduced, which uses for forming a seed layer before the main ITO deposition. We confirm that ITO films with seed layers are effective to obtain clean and smooth glass surfaces without un-etched ITO remnants, resulting in a good long-run electrical stability of the top-gate indium-gallium-zinc oxide-TTFT.

Deposition of very thin uniform indium sulfide layers over metallic nano-rods by the Spray-Ion Layer Gas Reaction method

Energy Technology Data Exchange (ETDEWEB)

Genduso, G. [Dipartimento di Ingegneria Chimica, Gestionale, Informatica, Meccanica, Università di Palermo, Viale delle Scienze, 90100 Palermo (Italy); Institut for Heterogeneous Material Systems, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Hahn-Meitner-Platz 1, D-14109 Berlin (Germany); Inguanta, R.; Sunseri, C.; Piazza, S. [Dipartimento di Ingegneria Chimica, Gestionale, Informatica, Meccanica, Università di Palermo, Viale delle Scienze, 90100 Palermo (Italy); Kelch, C.; Sáez-Araoz, R. [Institut for Heterogeneous Material Systems, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Hahn-Meitner-Platz 1, D-14109 Berlin (Germany); Zykov, A. [Institut for Heterogeneous Material Systems, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Hahn-Meitner-Platz 1, D-14109 Berlin (Germany); present address: Institut für Physik, Humboldt-Universität zu Berlin, Newtonstr. 15,12489 Berlin (Germany); Fischer, Ch.-H., E-mail: fischer@helmholtz-berlin.de [Institut for Heterogeneous Material Systems, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Hahn-Meitner-Platz 1, D-14109 Berlin (Germany); second affiliation: Free University Berlin, Chemistry Institute, Takustr. 3, D-14195 Berlin (Germany)

2013-12-02

Very thin and uniform layers of indium sulfide were deposited on nickel nano-rods using the sequential and cyclical Spray-ILGAR® (Ion Layer Gas Reaction) technique. Substrates were fabricated by electrodeposition of Ni within the pores of polycarbonate membranes and subsequent chemical dissolution of the template. With respect to the depositions on flat substrates, experimental conditions were modified and optimized for the present geometry. Our results show that nano-rods up to a length of 10 μm were covered uniformly along their full length and with an almost constant film growth rate, thus allowing a good control of the coating thickness; the effect of the deposition temperature was also investigated. However, for high numbers of process steps, i.e. thickness, the films became uneven and crusty, especially at higher temperature, mainly owing to the simultaneous side reaction of the metallic Ni forming nickel sulfide at the surface of the rods. However, such a problem occurs only in the case of reactive nano-rod materials, such as less noble metals. It could be strongly reduced by doubling the spray step duration and thereby sealing the metallic surface before the process step of the sulfurization. Thus, quite smooth, about 100 nm thick coatings could be obtained. - Highlights: • Ni nano-rod substrates were grown within polycarbonate membranes. • We can coat nano-rods uniformly by the Ion Layer Gas Reaction method. • As a model we deposited up to about 100 nm In{sub 2}S{sub 3} on Ni nanorods (250 nm × 10 μm). • Element mapping at insulated rods showed homogenous coating over the full length. • Parameter optimization reduced effectively the Ni sulfide formation.

Study on indium leaching from mechanically activated hard zinc residue

Directory of Open Access Journals (Sweden)

Yao J.H.

2011-01-01

Full Text Available In this study, changes in physicochemical properties and leachability of indium from mechanically activated hard zinc residue by planetary mill were investigated. The results showed that mechanical activation increased specific surface area, reaction activity of hard zinc residue, and decreased its particle size, which had a positive effect on indium extraction from hard zinc residue in hydrochloric acid solution. Kinetics of indium leaching from unmilled and activated hard zinc residue were also investigated, respectively. It was found that temperature had an obvious effect on indium leaching rate. Two different kinetic models corresponding to reactions which are diffusion controlled, [1-(1- x1/3]2=kt and (1-2x/3-(1-x2/3=kt were used to describe the kinetics of indium leaching from unmilled sample and activated sample, respectively. Their activation energies were determined to be 17.89 kJ/mol (umilled and 11.65 kJ/mol (activated within the temperature range of 30°C to 90°C, which is characteristic for a diffusion controlled process. The values of activation energy demonstrated that the leaching reaction of indium became less sensitive to temperature after hard zinc residue mechanically activated by planetary mill.

The Availability of Indium: The Present, Medium Term, and Long Term

Energy Technology Data Exchange (ETDEWEB)

Lokanc, Martin [Colorado School of Mines, Golden, CO (United States); Eggert, Roderick [Colorado School of Mines, Golden, CO (United States); Redlinger, Michael [Colorado School of Mines, Golden, CO (United States)

2015-10-01

Demand for indium is likely to increase if the growth in deployment of the copper-indium-gallium-selenide (CIGS) and III-V thin-film photovoltaic technologies accelerates. There are concerns about indium supply constraints since it is relatively rare element in the earth's crust and because it is produced exclusively as a byproduct.

The distribution of InCl sub x compounds in model polymeric LEDs A combined low and high-energy ion beam analysis study

CERN Document Server

Reijme, M A; Simons, D P L; Schok, M; Ijzendoorn, L J V; Brongersma, H H; De Voigt, M J A

2002-01-01

A combination of low- and high-energy ion beam analysis techniques was used to determine the distribution of indium chloride compounds in model polymeric light-emitting diodes (p-LEDs). Parts of polymeric LEDs (polydialkoxyphenylenevinylene (OC sub 1 C sub 1 sub 0 -PPV) on indium-tin-oxide (ITO) substrates) were exposed to a HCl/Ar flow to simulate the processes occurring during conversion of precursor PPVs and acid treatment of polymers. Samples with variable exposure times as well as pristine samples were studied with Rutherford backscattering spectrometry (RBS), low energy ion scattering (LEIS), X-ray photoelectron spectroscopy (XPS) and particle induced X-ray emission (PIXE). The RBS measurements show that after HCl exposure indium is distributed throughout the OC sub 1 C sub 1 sub 0 -PPV layer. LEIS and XPS measurements indicate that the indium and chlorine are present at the outermost surface of the OC sub 1 C sub 1 sub 0 -PPV layer. PIXE measurements in combination with the RBS data demonstrate that th...

Labelling of bacteria with indium chelates

International Nuclear Information System (INIS)

Kleinert, P.; Pfister, W.; Endert, G.; Sproessig, M.

1985-01-01

The indium chelates were prepared by reaction of radioactive indiumchloride with 10 μg oxine, 15 μg tropolone and 3 mg acetylacetone, resp. The formed chelates have been incubated with 10 9 germs/ml for 5 minutes, with labelling outputs from 90 to 95%. Both gram-positive (Streptococcus, Staphylococcus) and gram-negative bacteria (Escherichia coli) can be labelled. The reproductive capacity of the bacteria was not impaired. The application of indium labelled bacteria allows to show the distribution of microorganisms within the living organism and to investigate problems of bacterial adherence. (author)

Indium-111 oxine labelling of white blood cells

International Nuclear Information System (INIS)

Lavender, J.P.; Silvester, D.J.; Goldman, J.; Hammersmith Hospital, London

1978-01-01

Following work done by Professor John McAfee and Mathew Thakur at the MRS Cyclotron Unit a method is available for labelling cells with indium-111 which results in a stable intracellular marker. The method uses indium-111-8 hydroxyquinoline (111In oxine) which is a lipoid soluble complex which goes across the cell membrane and results in the deposition of indium into various subcellular structures. It has been applied to various preparations of white cells, platelets and also malignant cells. Autologous granulocytes have been used to identify inflammatory lesions in 35 patients. By similar means autologous lymphocytes can also be labelled and reinfused. Lymphocytes have been shown in animals to circulate from the blood via the lymphatic system and then returning to the blood once more. The same phenomenon can be seen in man using indium labelled lymphocytes. Lymph nodes become visible at between 12 and 18 hours and recirculation of labelled cells can be shown on the blood activity curves. Certain problems arise concerning cell behaviour after labelling which appear due to irradiation of cells rather than chemical toxicity. (author)

Indium tin oxide films prepared via wet chemical route

International Nuclear Information System (INIS)

Legnani, C.; Lima, S.A.M.; Oliveira, H.H.S.; Quirino, W.G.; Machado, R.; Santos, R.M.B.; Davolos, M.R.; Achete, C.A.; Cremona, M.

2007-01-01

In this work, indium tin oxide (ITO) films were prepared using a wet chemical route, the Pechini method. This consists of a polyesterification reaction between an α-hydroxicarboxylate complex (indium citrate and tin citrate) with a polyalcohol (ethylene glycol) followed by a post annealing at 500 deg. C. A 10 at.% of doping of Sn 4+ ions into an In 2 O 3 matrix was successfully achieved through this method. In order to characterize the structure, the morphology as well as the optical and electrical properties of the produced ITO films, they were analyzed using different experimental techniques. The obtained films are highly transparent, exhibiting transmittance of about 85% at 550 nm. They are crystalline with a preferred orientation of [222]. Microscopy discloses that the films are composed of grains of 30 nm average size and 0.63 nm RMS roughness. The films' measured resistivity, mobility and charge carrier concentration were 5.8 x 10 -3 Ω cm, 2.9 cm 2 /V s and - 3.5 x 10 20 /cm 3 , respectively. While the low mobility value can be related to the small grain size, the charge carrier concentration value can be explained in terms of the high oxygen concentration level resulting from the thermal treatment process performed in air. The experimental conditions are being refined to improve the electrical characteristics of the films while good optical, chemical, structural and morphological qualities already achieved are maintained

Thermoelectric flux effect in superconducting indium

International Nuclear Information System (INIS)

Van Harlingen, D.J.

1977-01-01

In this paper we discuss a thermoelectric effect in superconductors which provides a mechanism for studying quasiparticle relaxation and scattering processes in non-equilibrium superconductors by transport measurements. We report measurements of the thermoelecric flux effect in samples consisting of indium and lead near the In transition temperature; in this temperature range, the contribution to DELTA/sub TAU/ from the Pb is insignificant and so values of OMEGA(T) are obtained for indium. The results of our experiments may be summarized as follows: (1) we have a thermally-generated flux effect in 5 superconducting In-Pb toroidal samples, (2) experimental tests suggest that the observed effect does indeed arise from the proposed thermoelectric flux effect, (3) OMEGA(T) for indium is found to diverge as (T/sub c/ - T)/sup -3/2/ more rapidly than predicted by simple theory, (4) OMEGA(T) at T/T sub c/ = .999 is nearly 10/sup 5/ larger than initially expected, (5) OMEGA (T) roughly correlates with the magnitude of the normal state thermoelectric coefficient for our samples

Investigation into cathode polarization during deposition of rhodium-nickel and rhodium-indium alloys

International Nuclear Information System (INIS)

Evdokimova, N.V.; Byacheslavov, P.M.; Lokshtanova, O.G.

1979-01-01

The results of kinetic regularities experimental investigations during electrodeposition of rhodium-nickel and rhonium-indium alloys are presented. Methods of general and partial polarization curves have been used to show the nature of polarization during the rhonium-nickel and rhodium-indium alloys deposition. It is shown that indium into the rhodium-indium alloy and nickel into the rhodium-nickel alloy deposit with great depolarization ( PHIsub(In)sup(0)=-0.33B, PHIsub(Ni)sup(0)=-0.23B). Indium and nickel in pure form do not deposit from the electrolytes of the given composition (H 2 SO 4 - 50 g/l, HNH 2 SO 3 -10 g/l). The recalculation of partial polarization curve of indium precipitation into the rhodium-indium alloy in the mixed kinetics coordinates gives a straight line with 40 mV inclination angle. This corresponds to the delayed stage of the second electron addition with the imposition of diffusion limitations

Average formation number n-barOH of colloid-type indium hydroxide

International Nuclear Information System (INIS)

Stefanowicz, T.; Szent-Kirallyine Gajda, J.

1983-01-01

Indium perchlorate in perchloric acid solution was titrated with sodium hydroxide solution to various pH values. Indium hydroxide colloid was removed by ultracentrifugation and supernatant solution was titrated with base to neutral pH. The two-stage titration data were used to calculate the formation number of indium hydroxide colloid, which was found to equal n-bar OH = 2.8. (author)

Preparation of transparent conductive indium tin oxide thin films from nanocrystalline indium tin hydroxide by dip-coating method

International Nuclear Information System (INIS)

Koroesi, Laszlo; Papp, Szilvia; Dekany, Imre

2011-01-01

Indium tin oxide (ITO) thin films with well-controlled layer thickness were produced by dip-coating method. The ITO was synthesized by a sol-gel technique involving the use of aqueous InCl 3 , SnCl 4 and NH 3 solutions. To obtain stable sols for thin film preparation, as-prepared Sn-doped indium hydroxide was dialyzed, aged, and dispersed in ethanol. Polyvinylpyrrolidone (PVP) was applied to enhance the stability of the resulting ethanolic sols. The transparent, conductive ITO films on glass substrates were characterized by X-ray diffraction, scanning electron microscopy and UV-Vis spectroscopy. The ITO layer thickness increased linearly during the dipping cycles, which permits excellent controllability of the film thickness in the range ∼ 40-1160 nm. After calcination at 550 o C, the initial indium tin hydroxide films were transformed completely to nanocrystalline ITO with cubic and rhombohedral structure. The effects of PVP on the optical, morphological and electrical properties of ITO are discussed.

Electrical effect of titanium diffusion on amorphous indium gallium zinc oxide

International Nuclear Information System (INIS)

Choi, Seung-Ha; Jung, Woo-Shik; Park, Jin-Hong

2012-01-01

In this work, thermal diffusion phenomenon of Ti into amorphous indium gallium zinc oxide (α-IGZO) was carefully investigated with secondary ion mass spectroscopy, I-V, and R s measurement systems and HSC chemistry simulation tool. According to the experimental and simulated results, the diffused Ti atoms were easily oxidized due to its lowest oxidation free energy. Since oxygen atoms were decomposed from the α-IGZO during the oxidation of Ti, the number of oxygen vacancies working as electron-donating sites in α-IGZO was dramatically increased, contributing to the decrease of resistivity (ρ) from 1.96 Ω cm (as-deposited α-IGZO) to 1.33 × 10 −3 Ω cm (350 °C annealed α-IGZO).

Quantification of indium in steel using PIXE

International Nuclear Information System (INIS)

Oliver, A.; Miranda, J.; Rickards, J.; Cheang, J.C.

1989-01-01

The quantitative analysis of steel endodontics tools was carried out using low-energy protons (≤ 700 keV). A computer program for a thick-target analysis which includes enhancement due to secondary fluorescence was used. In this experiment the L-lines of indium are enhanced due to the proximity of other elements' K-lines to the indium absorption edge. The results show that the ionization cross section expression employed to evaluate this magnitude is important. (orig.)

Quantification of indium in steel using PIXE

Energy Technology Data Exchange (ETDEWEB)

Oliver, A.; Miranda, J.; Rickards, J.; Cheang, J.C.

1989-04-01

The quantitative analysis of steel endodontics tools was carried out using low-energy protons (/le/ 700 keV). A computer program for a thick-target analysis which includes enhancement due to secondary fluorescence was used. In this experiment the L-lines of indium are enhanced due to the proximity of other elements' K-lines to the indium absorption edge. The results show that the ionization cross section expression employed to evaluate this magnitude is important. (orig.).

The indium-oxygen system, ch. 5

International Nuclear Information System (INIS)

Dillen, A.J. van

1977-01-01

This chapter is divided into three sections: 1) a survey of the literature concerning the indiumoxygen system, 2) the adsorption of oxygen at pure and partially oxidized indium surfaces in the temperature range 20-180degC, and 3) the oxidation of indium at temperatures above 180degC. The oxygen uptake is determined volumetrically and gravimetrically. The influence of the melting point is considered and the results are compared with data from the literature. The oxide layer is amorphous at lower temperatures but above 350degC, crystallisation of In 2 O 3 takes place

Electroless formation of hybrid lithium anodes for fast interfacial ion transport

Energy Technology Data Exchange (ETDEWEB)

Choudhury, Snehashis; Stalin, Sanjuna; Vu, Duylinh; Fawole, Kristen; Archer, Lynden A. [School of Chemical and Biomolecular Engineering, Cornell University, Ithaca, NY (United States); Tu, Zhengyuan [Department of Material Science and Engineering, Cornell University, Ithaca, NY (United States); Gunceler, Deniz [Department of Physics, Cornell University, Ithaca, NY (United States); Sundararaman, Ravishankar [Material Science and Engineering, Rensselaer Polytechnic Institute, Troy, NY (United States)

2017-10-09

Rechargeable batteries based on metallic anodes are of interest for fundamental and application-focused studies of chemical and physical kinetics of liquids at solid interfaces. Approaches that allow facile creation of uniform coatings on these metals to prevent physical contact with liquid electrolytes, while enabling fast ion transport, are essential to address chemical instability of the anodes. Here, we report a simple electroless ion-exchange chemistry for creating coatings of indium on lithium. By means of joint density functional theory and interfacial characterization experiments, we show that In coatings stabilize Li by multiple processes, including exceptionally fast surface diffusion of lithium ions and high chemical resistance to liquid electrolytes. Indium coatings also undergo reversible alloying reactions with lithium ions, facilitating design of high-capacity hybrid In-Li anodes that use both alloying and plating approaches for charge storage. By means of direct visualization, we further show that the coatings enable remarkably compact and uniform electrodeposition. The resultant In-Li anodes are shown to exhibit minimal capacity fade in extended galvanostatic cycling when paired with commercial-grade cathodes. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Synthesis and characterization of five-coordinated indium amidinates

Energy Technology Data Exchange (ETDEWEB)

Riahi, Yasaman

2016-07-29

The focus of this work is synthesis, characterization and exploring the reactivity of new indium amidinate compounds of the type R{sub 2}InX (R = R''NCR'NR''; R' = Ph, R'' = SiMe{sub 3}, iPr, dipp; X = Br, Cl) with the coordination number of five and R{sub 3}In (R = Me{sub 3}SiNCPhNSiMe{sub 3}) with the coordination number of six. By using amidinates as chelating ligands the electron deficiency of indium atom will be resolved. Additionally, by using different substituents the study of the different synthesized indium amidinates has become possible. The selected method for the synthesis allows the carbodiimides to react with organolithium compounds to get the corresponding lithium amidinates. Afterwards the resulting lithium amidinates take part in transmetalation reactions with InBr{sub 3} and InCl{sub 3}. The study of the reactivity of indium amidinate complexes including nucleophilic reactions as well as their reduction were also examined. Beside crystal structure analysis, nuclear magnetic resonance spectroscopy as well as elemental analysis has been applied to characterize the compounds.

Solvothermal synthesis of gallium-indium-zinc-oxide nanoparticles for electrolyte-gated transistors.

Science.gov (United States)

Santos, Lídia; Nunes, Daniela; Calmeiro, Tomás; Branquinho, Rita; Salgueiro, Daniela; Barquinha, Pedro; Pereira, Luís; Martins, Rodrigo; Fortunato, Elvira

2015-01-14

Solution-processed field-effect transistors are strategic building blocks when considering low-cost sustainable flexible electronics. Nevertheless, some challenges (e.g., processing temperature, reliability, reproducibility in large areas, and cost effectiveness) are requirements that must be surpassed in order to achieve high-performance transistors. The present work reports electrolyte-gated transistors using as channel layer gallium-indium-zinc-oxide nanoparticles produced by solvothermal synthesis combined with a solid-state electrolyte based on aqueous dispersions of vinyl acetate stabilized with cellulose derivatives, acrylic acid ester in styrene and lithium perchlorate. The devices fabricated using this approach display a ION/IOFF up to 1 × 10(6), threshold voltage (VTh) of 0.3-1.9 V, and mobility up to 1 cm(2)/(V s), as a function of gallium-indium-zinc-oxide ink formulation and two different annealing temperatures. These results validates the usage of electrolyte-gated transistors as a viable and promising alternative for nanoparticle based semiconductor devices as the electrolyte improves the interface and promotes a more efficient step coverage of the channel layer, reducing the operating voltage when compared with conventional dielectrics gating. Moreover, it is shown that by controlling the applied gate potential, the operation mechanism of the electrolyte-gated transistors can be modified from electric double layer to electrochemical doping.

Synthesis of Indium Nanowires by Galvanic Displacement and Their Optical Properties

Directory of Open Access Journals (Sweden)

Hope Greg

2008-01-01

Full Text Available Abstract Single crystalline indium nanowires were prepared on Zn substrate which had been treated in concentrated sulphuric acid by galvanic displacement in the 0.002 mol L−1In2(SO43-0.002 mol L−1SeO2-0.02 mol L−1SDS-0.01 mol L−1citric acid aqueous solution. The typical diameter of indium nanowires is 30 nm and most of the nanowires are over 30 μm in length. XRD, HRTEM, SAED and structural simulation clearly demonstrate that indium nanowires are single-crystalline with the tetragonal structure, the growth direction of the nanowires is along [100] facet. The UV-Vis absorption spectra showed that indium nanowires display typical transverse resonance of SPR properties. The surfactant (SDS and the pretreatment of Zn substrate play an important role in the growth process. The mechanism of indium nanowires growth is the synergic effect of treated Zn substrate (hard template and SDS (soft template.

Synthesis and decomposition of a novel carboxylate precursor to indium oxide

Science.gov (United States)

Hepp, Aloysius F.; Andras, Maria T.; Duraj, Stan A.; Clark, Eric B.; Hehemann, David G.; Scheiman, Daniel A.; Fanwick, Phillip E.

1994-01-01

Reaction of metallic indium with benzoyl peroxide in 4-1 methylpyridine (4-Mepy) at 25 C produces an eight-coordinate mononuclear indium(III) benzoate, In(eta(sup 2)-O2CC6H5)3(4-Mepy)2 4H2O (I), in yields of up to 60 percent. The indium(III) benzoate was fully characterized by elemental analysis, spectroscopy, and X-ray crystallography; (I) exists in the crystalline state as discrete eight-coordinate molecules; the coordination sphere around the central indium atom is best described as pseudo-square pyramidal. Thermogravimetric analysis of (I) and X-ray diffraction powder studies on the resulting pyrolysate demonstrate that this new benzoate is an inorganic precursor to indium oxide. Decomposition of (I) occurs first by loss of 4-methylpyridine ligands (100 deg-200 deg C), then loss of benzoates with formation of In2O3 at 450 C. We discuss both use of carboxylates as precursors and our approach to their preparation.

Thermal expansion and volumetric changes during indium phosphide melting

International Nuclear Information System (INIS)

Glazov, V.M.; Davletov, K.; Nashel'skij, A.Ya.; Mamedov, M.M.

1977-01-01

The results of the measurements of a thermal expansion were summed up at various temperatures as a diagram in coordinates (Δ 1/1) approximately F(t). It was shown that an appreciable deviation of the relationship (Δ1/1) approximately f(t) from the linear law corresponded to a temperature of 500-550 deg C. It was noted that the said deviation was related to an appreciable thermal decomposition of indium phosphide as temperature increased. The strength of the inter-atomic bond of indium phosphide was calculated. Investigated were the volumetric changes of indium phosphide on melting. The resultant data were analyzed with the aid of the Clausius-Clapeyron equation

Method for forming indium oxide/n-silicon heterojunction solar cells

Science.gov (United States)

Feng, Tom; Ghosh, Amal K.

1984-03-13

A high photo-conversion efficiency indium oxide/n-silicon heterojunction solar cell is spray deposited from a solution containing indium trichloride. The solar cell exhibits an Air Mass One solar conversion efficiency in excess of about 10%.

ITO/InP solar cells: A comparison of devices fabricated by ion beam and RF sputtering of the ITO

Science.gov (United States)

Coutts, T. J.

1987-01-01

This work was performed with the view of elucidating the behavior of indium tin oxide/indium phosphide (ITO/InP) solar cells prepared by RF and ion beam sputtering. It was found that using RF sputter deposition of the ITO always leads to more efficient devices than ion beam sputter deposition. An important aspect of the former technique is the exposure of the single crystal p-InP substrates to a very low plasma power prior to deposition. Substrates treated in this manner have also been used for ion beam deposition of ITO. In this case the cells behave very similarly to the RF deposited cells, thus suggesting that the lower power plasma exposure (LPPE) is the crucial process step.

Radiochemical studies of the separation of some chloro-complexes of tin, antimony, cadmium and indium

International Nuclear Information System (INIS)

Ramamoorthy, N.; Mani, R.S.

1976-01-01

Radioisotopes of tin, antimony, cadmium and indium such as tin-113, antimony-124, antimony-125, cadmium-109, cadmium-115, indium-113m and indium-111 find extensive applications as tracers in various fields. These isotopes are produced by irradiation of targets in a reactor or a cyclotron. It is usually observed that in addition to the nuclear reactions giving rise to the desired isotopes, side reactions also take place giving rise to radionuclidic contaminants. Thus, antimony-125, indium-114m and indium-114 will be present in the cyclotron produced indium-111. The authors have studied column chromatography over hydrous zirconia for the separation of antimony from tin and indium, and cadmium from indium. These studies have thrown light on the role and behaviour of antimony-125 present as an impurity in tin-113 during the preparation of tin-113-indium-113m generators and have indicated methods for the preparation of 115 Cd-sup(115m)In generators and for separation of 111 In from proton irradiated cadmium targets. (Authors)

First-principles investigation of indium diffusion in a silicon substrate

International Nuclear Information System (INIS)

Yoon, Kwan-Sun; Hwang, Chi-Ok; Yoo, Jae-Hyun; Won, Tae-Young

2006-01-01

In this paper, we report the total energy, the minimum energy path, and the migration energy of indium in a silicon substrate by using ab-initio calculations. Stable configurations during indium diffusion were obtained from the calculation of the total energy, and we estimated the minimum energy path (MEP) with the nudged elastic band (NEB) method. After finding the MEP, we found the energy barrier for the diffusion of indium to be 0.8 eV from an exact calculation of the total energies at the minimum and the transition state.

Spectrophotometric determination of indium with chromazurol S and dimethyllaurylbenzylammonium bromide

International Nuclear Information System (INIS)

Kwapulinska, G.; Buhl, F.

1988-01-01

The ternary system: indium-chromazurol S (CHAS)-dimethyllaurylbenzylammonium bromide (ST) was applied for determination of microgramme amounts of indium. The addition of ST enhances the sensitivity of the method; at λ max =625 nm the molar absorptivity of In-CHAS-ST complex equals 1.74 x 10 5 . The system obeyes the Lambert-Beer law in the range of indium concentration from 0.04 to 0.48 ppm. The maximal absorbance was obtained at pH 6. The complex is formed immediately and is stable during 2 hours. 3 figs., 10 refs. (author)

Two-Step Plasma Process for Cleaning Indium Bonding Bumps

Science.gov (United States)

Greer, Harold F.; Vasquez, Richard P.; Jones, Todd J.; Hoenk, Michael E.; Dickie, Matthew R.; Nikzad, Shouleh

2009-01-01

A two-step plasma process has been developed as a means of removing surface oxide layers from indium bumps used in flip-chip hybridization (bump bonding) of integrated circuits. The two-step plasma process makes it possible to remove surface indium oxide, without incurring the adverse effects of the acid etching process.

Blocking of indium incorporation by antimony in III-V-Sb nanostructures

International Nuclear Information System (INIS)

Sanchez, A M; Beltran, A M; Ben, T; Molina, S I; Beanland, R; Gass, M H; De la Pena, F; Walls, M; Taboada, A G; Ripalda, J M

2010-01-01

The addition of antimony to III-V nanostructures is expected to give greater freedom in bandgap engineering for device applications. One of the main challenges to overcome is the effect of indium and antimony surface segregation. Using several very high resolution analysis techniques we clearly demonstrate blocking of indium incorporation by antimony. Furthermore, indium incorporation resumes when the antimony concentration drops below a critical level. This leads to major differences between nominal and actual structures.

Spectral analysis of the fifth spectrum of indium: In V

International Nuclear Information System (INIS)

Swapnil; Tauheed, A.

2016-01-01

The fifth spectrum of indium (In V) has been investigated in the grazing and normal incidence wavelength regions. In"4"+ is a Rh-like ion with the ground configuration 4p"64d"9 and first excited configurations of the type 4p"64d"8nℓ (n≥4). The theoretical predications for this ion were made by Cowan's quasi-relativistic Hartree–Fock code with superposition of configurations involving 4p"64d"8(5p+6p+7p+4f+5f+6f), 4p"54d"1"0, 4p"64d"75s(5p+4f) for the odd parity matrix and 4p"64d"8 (5s+6s+7s+5d+6d), 4p"64d"7(5s"2+5p"2) for the even parity system. The spectra used for this work were recorded on 10.7 m grazing and normal incidence spectrographs at the National Institute of Standards and Technology, Gaithersburg, Maryland (USA) and also on a 3-m normal incidence vacuum spectrograph at Antigonish (Canada). The sources used were a sliding spark and a triggered spark respectively. Two hundred and thirty two energy levels based on the identification of 873 spectral lines have been established, forty six being new. Least squares fitted parametric calculations were used to interpret the observed level structure. The energy levels were optimized using a level optimization computer program (LOPT). Our wavelength accuracy for sharp and unblended lines is estimated to be within ±0.005 Å for λ below 400 Å and ±0.006 Å up to 1200 Å. - Highlights: • Indium spectra were recorded on both grazing and normal incidence spectrographs. • Calculations were made with Cowan's quasi-relativistic Hartree–Fock code. • New atomic transitions of In V were identified with newly found energy levels. • Uncertainties and Ritz wavelengths of all observed transitions were calculated. • Weighted transition probabilities (gA) were calculated.

Anelasticity of polycrystalline indium

Energy Technology Data Exchange (ETDEWEB)

Sapozhnikov, K., E-mail: k.sapozhnikov@mail.ioffe.ru [A.F.Ioffe Physical-Technical Institute, Politekhnicheskaya 26, 194021 St. Petersburg (Russian Federation); Golyandin, S. [A.F.Ioffe Physical-Technical Institute, Politekhnicheskaya 26, 194021 St. Petersburg (Russian Federation); Kustov, S. [Dept. de Fisica, Universitat de les Illes Balears, Cra Valldemossa km 7.5, E 07122 Palma de Mallorca (Spain)

2009-09-15

Mechanisms of anelasticity of polycrystalline indium have been studied over wide ranges of temperature (7-320 K) and strain amplitude (2 x 10{sup -7}-3.5 x 10{sup -4}). Measurements of the internal friction and Young's modulus have been performed by means of the piezoelectric resonant composite oscillator technique using longitudinal oscillations at frequencies of about 100 kHz. The stages of the strain amplitude dependence of the internal friction and Young's modulus defect, which can be attributed to dislocation - point defect and dislocation - dislocation interactions, have been revealed. It has been shown that thermal cycling gives rise to microplastic straining of polycrystalline indium due to the anisotropy of thermal expansion and to appearance of a 'recrystallization' internal friction maximum in the temperature spectra of amplitude-dependent anelasticity. The temperature range characterized by formation of Cottrell's atmospheres of point defects around dislocations has been determined from the acoustic data.

Photoluminescence of monovalent indium centres in phosphate glass

OpenAIRE

Masai, Hirokazu; Yamada, Yasuhiro; Okumura, Shun; Yanagida, Takayuki; Fujimoto, Yutaka; Kanemitsu, Yoshihiko; Ina, Toshiaki

2015-01-01

Valence control of polyvalent cations is important for functionalization of various kinds of materials. Indium oxides have been used in various applications, such as indium tin oxide in transparent electrical conduction films. However, although metastable In+ (5 s2 configuration) species exhibit photoluminescence (PL), they have attracted little attention. Valence control of In+ cations in these materials will be important for further functionalization. Here, we describe In+ species using PL ...

Properties of Polydisperse Tin-doped Dysprosium and Indium Oxides

Directory of Open Access Journals (Sweden)

Malinovskaya Tatyana

2017-01-01

Full Text Available The results of investigations of the complex permittivity, diffuse-reflectance, and characteristics of crystal lattices of tin-doped indium and dysprosium oxides are presented. Using the methods of spectroscopy and X-ray diffraction analysis, it is shown that doping of indium oxide with tin results in a significant increase of the components of the indium oxide complex permittivity and an appearance of the plasma resonance in its diffuse-reflectance spectra. This indicates the appearance of charge carriers with the concentration of more than 1021 cm−3 in the materials. On the other hand, doping of the dysprosium oxide with the same amount of tin has no effect on its optical and electromagnetic properties.

Stability aspects of hydrogen-doped indium oxide

OpenAIRE

Jost, Gabrielle; Hamri, Alexander Nordin; Köhler, Florian; Hüpkes, Jürgen

2015-01-01

Transparent conductive oxides play an important role as contact layers in various opto-electronic devices such as solar cells or LEDs. Whilst crystalline materials e.g. zinc oxide (ZnO), tin oxide (Sn2O3) or tin doped indium oxide (ITO) have already been vastly investigated and applied [1] hydrogen doped indium oxide (In2O3:H) entered the scene a while ago as a new material with a superior trade-off between electrical and optical performance. In2O3:H is commonly deposited at room temperature...

Indium 111 leucocyte scintigraphy in abdominal sepsis

International Nuclear Information System (INIS)

Baba, A.A.; McKillop, J.H.; Gray, H.W.; Cuthbert, G.F.; Neilson, W.; Anderson, J.R.

1990-01-01

We have studied the clinical utility of indium 111 autologous leucocyte scintigraphy retrospectively in 45 patients presenting with suspected intra-abdominal sepsis. The sensitivity was 95% (21/22) and the specificity was 91% (21/23). Some 34 of the studies (17 positive and 17 negative) were considered helpful in furthering patient management (76%) and 8, unhelpful (18%). In 3, the study results were misleading and led to inappropriate treatment. Indium 111 scintigraphy, whether positive or negative, provides information in patients with suspected intra-abdominal sepsis upon which therapeutic decisions can be based. (orig.)

Polarographic studies about indium (III) behaviour in aqueous media of sodium azide

International Nuclear Information System (INIS)

Tokoro, R.

1988-01-01

The present study shows some polarographic behavior of indium (III) in azide media that is close those observed in a thiocyanate solution. The presence of azide ligand decreases the overpotential in the discharge of indium whose catalytic character can be explained by formation of an azide bridge between electrode and indium (III) increasing the speed of electron transfer. The discharge of indium in azide media is diffusion controlled. As the azide concentration is increased the half wave potential displaces in the cathodic direction. This displacement is due to complex formation. The number of electrons, n, involved in the total process was estimates by the reversible polarographic equation to be 2,7. The potentiostatic coulometry of indium in azide/hydrazoic acid buffer showed a catalytic process where the chemistry regeneration was performed by reaction of hydrazoic acid and indium amalgam. The electrochemistry evidence was the constancy of current as the electrolysis proceeded. The chemistry aspect was the presence of ammonium cation in electrolysed solution. The catalytic process with chemistry regeneration and the formation of a bridge by azide could explain the higher value of current in azide media compared to perchlorate solution. (author) [pt

Selectivity enhancement of indium-doped SnO2 gas sensors

International Nuclear Information System (INIS)

Salehi, A.

2002-01-01

Indium doping was used to enhance the selectivity of SnO 2 gas sensor. Both indium-doped and undoped SnO 2 gas sensors fabricated with different deposition techniques were investigated. The changes in the sensitivity of the sensors caused by selective gases (hydrogen and wood smoke) ranging from 500 to 3000 ppm were measured at different temperatures from 50 to 300 deg. C. The sensitivity peaks of the samples exhibit different values for selective gases with a response time of approximately 0.5 s. Thermally evaporated indium-doped SnO 2 gas sensor shows a considerable increase in the sensitivity peak of 27% in response to wood smoke, whereas it shows a sensitivity peak of 7% to hydrogen. This is in contrast to the sputter deposited indium-doped SnO 2 gas sensor, which exhibits a much lower sensitivity peak of approximately 2% to hydrogen and wood smoke compared to undoped SnO 2 gas sensors fabricated by chemical vapor deposition and spray pyrolysis. Scanning electron microscopy shows that different deposition techniques result in different porosity of the films. It is observed that the thermally evaporated indium-doped SnO 2 gas sensor shows high porosity, while the sputtered sample exhibits almost no porosity

Indium determination by spectral overlappings of lines in atomic absorption spectrometry

International Nuclear Information System (INIS)

Gomez, J.J.; Huicque, L. d'; Garcia Vior, L.O.

1991-01-01

A molybdenum hollow-cathode lamp filled with neon can be used to determine indium. Characteristic concentration for this element is 4.5 mg/L in the 325 nm spectral region for the Mo(I) 325.621 nm line. In addition, values of 0.4 mg/L and 0.3 mg/L are obtained with the Mo(I) 410.215 nm and Ne(I) 451.151 nm lines, respectively. These spectral overlappings allow the determination of indium in silver-cadmium-indium alloys. (Author) [es

Pharmacokinetics of indium-111-labeled antimyosin monoclonal antibody in murine experimental viral myocarditis

International Nuclear Information System (INIS)

Yamada, T.; Matsumori, A.; Watanabe, Y.; Tamaki, N.; Yonekura, Y.; Endo, K.; Konishi, J.; Kawai, C.

1990-01-01

The pharmacokinetics of indium-111-labeled antimyosin monoclonal antibody Fab were investigated with use of murine experimental viral myocarditis as a model. The biodistribution of indium-111-labeled antimyosin antibody Fab on days 3, 5, 7, 14, 21 and 28 after encephalomyocarditis virus inoculation demonstrated that myocardial uptake increased significantly on days 5, 7 and 14 (maximum on day 7) in infected versus uninfected mice (p less than 0.001). In vivo kinetics in infected mice on day 7 demonstrated that the heart to blood ratio reached a maximum 48 h after the intravenous administration of indium-111-labeled antimyosin Fab, which was considered to be the optimal time for scintigraphy. The scintigraphic images obtained with indium-111-labeled antimyosin Fab demonstrated positive uptake in the cardiac lesion in infected mice. The pathologic study demonstrated that myocardial uptake correlated well with pathologic grades of myocardial necrosis. High performance liquid chromatography revealed the presence of an antigen-antibody complex in the circulation of infected mice after the injection of indium-111-labeled antimyosin Fab. This antigen bound to indium-111-labeled antimyosin Fab in the circulation might be whole myosin and this complex may decrease myocardial uptake and increase liver uptake. It is concluded that indium-111-labeled antimyosin monoclonal antibody Fab accumulates selectively in damaged heart tissue in mice with acute myocarditis and that indium-111-labeled antimyosin Fab scintigraphy may be a useful method for the visualization of acute myocarditis

Ion irradiation effect on metallic condensate adhesion to glass

International Nuclear Information System (INIS)

Kovalenko, V.V.; Upit, G.P.

1984-01-01

The ion irradiation effect on metallic condensate adhesion to glass is investigated. It has been found that in case of indium ion deposition the condensate adhesion to glass cleavages being in contact with atmosphere grows up to the level corresponding to a juvenile surface while in case of argon ion irradiation - exceeds it. It is shown that the observed adhesion growth is determined mainly by the surfwce modification comparising charge accumulation on surface, destruction of a subsurface layer and an interlayer formation in the condensate-substrate interface. The role of these factors in the course of various metals deposition is considered

Indium nanoparticles for ultraviolet surface-enhanced Raman spectroscopy

Science.gov (United States)

Das, Rupali; Soni, R. K.

2018-05-01

Ultraviolet Surface-enhanced Raman spectroscopy (UVSERS) has emerged as an efficient molecular spectroscopy technique for ultra-sensitive and ultra-low detection of analyte concentration. The generic SERS substrates based on gold and silver nanostructures have been extensively explored for high local electric field enhancement only in visible-NIR region of the electromagnetic spectrum. The template synthesis of controlled nanoscale size metallic nanostructures supporting localized surface plasmon resonance (LSPR) in the UV region have been recently explored due to their ease of synthesis and potential applications in optoelectronic, catalysis and magnetism. Indium (In0) nanoparticles exhibit active surface plasmon resonance (SPR) in ultraviolet (UV) and deep-ultaviolet (DUV) region with optimal absorption losses. This extended accessibility makes indium a promising material for UV plasmonic, chemical sensing and more recently in UV-SERS. In this work, spherical indium nanoparticles (In NPs) were synthesized by modified polyol reduction method using NaBH4 having local surface plasmon resonance near 280 nm. The as-synthesized spherical In0 nanoparticles were then coated with thin silica shells of thickness ˜ 5nm by a modified Stober method protecting the nanoparticles from agglomeration, direct contact with the probed molecules as well as prevent oxidation of the nanoparticles. Morphological evolution of In0 nanoparticles and SiO2 coating were characterized by transmission electron microscope (TEM). An enhanced near resonant shell-isolated SERS activity from thin film of tryptophan (Tryp) molecules deposited on indium coated substrates under 325nm UV excitation was observed. Finite difference time domain (FDTD) method is employed to comprehend the experimental results and simulate the electric field contours which showed amplified electromagnetic field localized around the nanostructures. The comprehensive analysis indicates that indium is a promising alternate

Evolution of the chemical bonding nature and electrode activity of indium selenide upon the composite formation with graphene nanosheets

International Nuclear Information System (INIS)

Oh, Seung Mi; Lee, Eunsil; Adpakpang, Kanyaporn; Patil, Sharad B.; Park, Mi Jin; Lim, Young Soo; Lee, Kyu Hyoung; Kim, Jong-Young; Hwang, Seong-Ju

2015-01-01

Graphical abstract: Display Omitted -- Highlights: • In 4 Se 2.85 @graphene nanocomposite is easily prepared by high energy mechanical milling process. • The bond covalency of In 4 Se 2.85 is notably changed upon the composite formation with graphene. • In 4 Se 2.85 @graphene nanocomposite shows promising anode performance for lithium ion battery. -- Abstract: Evolution of the chemical bonding nature and electrochemical activity of indium selenide upon the composite formation with carbon species is systematically investigated. Nanocomposites of In 4 Se 2.85 @graphene and In 4 Se 2.85 @carbon-black are synthesized via a solid state reaction between In and Se elements, and the following high energy mechanical milling of In 4 Se 2.85 with graphene and carbon-black, respectively. The high energy mechanical milling (HEMM) of In 4 Se 2.85 with carbon species gives rise to a decrease of particle size with a significant depression of the crystallinity of In 4 Se 2.85 phase. In contrast to the composite formation with carbon-black, that with graphene induces a notable decrease of (In−Se) bond covalency, underscoring significant chemical interaction between graphene and In 4 Se 2.85 . Both the nanocomposites of In 4 Se 2.85 @graphene and In 4 Se 2.85 @carbon-black show much better anode performance for lithium ion batteries with larger discharge capacity and better cyclability than does the pristine In 4 Se 2.85 material, indicating the beneficial effect of composite formation on the electrochemical activity of indium selenide. Between the present nanocomposites, the electrode performance of the In 4 Se 2.85 @graphene nanocomposite is superior to that of the In 4 Se 2.85 @carbon-black nanocomposite, which is attributable to the weakening of (In−Se) bonds upon the composite formation with graphene as well as to the better mixing between In 4 Se 2.85 and graphene. The present study clearly demonstrates that the composite formation with graphene has strong influence

Synthesis of indium-labeled antibody-chelate conjugates for radioassays

Energy Technology Data Exchange (ETDEWEB)

Gokce, A; Nakamura, R M; Tubis, M; Wolf, W

1982-01-01

A method has been developed to achieve rapid and reproducible complexation of indium to transferrin at pH 7.4. The system consists of nitrilotriacetic acid (NTA) as the intermediate carrier ligand, whose function is to allow the /sup 113/m In ion, in a solution in Tris buffer, pH 7.4, to be transferred rapidly to the specific binding sites on transferrin. Just as in the case of iron, this complexation requires the presence of a synergistic ion such as bicarbonate. The present system can be used to allow the binding of /sup 113/mIn to transferrin when coupled to an antibody. This method has been tested by studying the conjugation of an antibody, the IgG fraction of goat anti-rabbit-IgG, with either transferrin or desferoxamine, using glutaraldehyde as the coupling agent. Optimization in terms of total protein concentration and glutaraldehyde levels lead to products where the specific metal binding capacity of the transferrin moiety remains unchanged, and where the antibody retains 70% of its antigenic activity. The present system can be considered an extension of the ELISA techniques and can be used to determine, by a terminal /sup 113/mIn labeling technique, the level of specific binding of an antibody to its antigen.

Structural and microstructural changes in the zirconium-indium mixed oxide system during the thermal treatment

Science.gov (United States)

Štefanić, G.; Štefanić, I. I.; Musić, S.; Ivanda, M.

2011-05-01

The zirconium-indium mixed oxide systems on both the zirconium- and the indium-rich side of the concentration range were prepared by co-precipitation from aqueous solutions of the corresponding salts, followed by washing and heat-treatment. The thermal behavior (up to 1000 °C) of the dried samples was examined by X-ray powder diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, energy dispersive X-ray spectrometry, differential thermal analysis and thermogravimetric measurements. The obtained results show that the increase in the amount of the second phase causes an increase of both the crystallization temperature of the amorphous precursors of ZrO 2, from 435 °C (0 mol.% of InO 1.5) to 476 °C (˜62 mol.% of InO 1.5), and of the topotactic transition temperature of cubic In(OH) 3 to cubic In 2O 3, from 259 °C (0 mol.% of ZrO 2) to 290 °C (˜25 mol.% of ZrO 2). The amorphous precursors of ZrO 2 phase exhibit an extended capability to incorporate In 3+ ions (more than 60 mol.%). With a rise in temperature the maximum solubility of In 3+ ions in the ZrO 2 lattice decreases from ˜55 mol.% in the crystallization products obtained after calcination at 400 °C to ˜10 mol.% after calcination at 1000 °C. The results of phase analysis indicate that the incorporation of In 3+ ions partially stabilized both the tetragonal and cubic ZrO 2 polymorphs. The maximum solubility of Zr 4+ ions in the starting In(OH) 3 lattice was estimated at ˜10 mol.%. Thermal treatment causes a small increase of Zr 4+ ion solubility limits, estimated at ˜15 mol.% in the cubic In 2O 3 lattice after calcination at 1000 °C. Precise lattice parameter measurements, by using Le Bail refinements of the powder diffraction patterns with added silicon as an internal standard, show that the incorporation of In 3+ ions caused a very small decrease of the cubic ZrO 2 lattice, while the incorporation of Zr 4+ ions had a negligible

Temperature dependent structural and vibrational properties of liquid indium

Science.gov (United States)

Patel, A. B.; Bhatt, N. K.

2018-05-01

The influence of the temperature effect on both the structure factor and the phonon dispersion relation of liquid indium have been investigated by means of pseudopotential theory. The Percus-Yevick Hard Sphere reference system is applied to describe the structural calculation. The effective electron-ion interaction is explained by using modified empty core potential due to Hasegawa et al. along with a local field correction function due to Ichimaru-Utsumi (IU). The temperature dependence of pair potential needed at higher temperatures was achieved by multiplying the damping factor exp(- π/kBT2k F r ) in the pair potential. Very close agreement of static structure factor, particularly, at elevated temperatures confirms the validity of the local potential. A positive dispersion is found in low-q region and the correct trend of phonon dispersion branches like the experimental; shows all broad features of collective excitations in liquid metals.

Acid-catalyzed kinetics of indium tin oxide etching

Energy Technology Data Exchange (ETDEWEB)

Choi, Jae-Hyeok; Kim, Seong-Oh; Hilton, Diana L. [School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Centre for Biomimetic Sensor Science, Nanyang Technological University, 50 Nanyang Drive, 637553 (Singapore); Cho, Nam-Joon, E-mail: njcho@ntu.edu.sg [School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Centre for Biomimetic Sensor Science, Nanyang Technological University, 50 Nanyang Drive, 637553 (Singapore); School of Chemical and Biomedical Engineering, Nanyang Technological University, 62 Nanyang Drive, 637459 (Singapore)

2014-08-28

We report the kinetic characterization of indium tin oxide (ITO) film etching by chemical treatment in acidic and basic electrolytes. It was observed that film etching increased under more acidic conditions, whereas basic conditions led to minimal etching on the time scale of the experiments. Quartz crystal microbalance was employed in order to track the reaction kinetics as a function of the concentration of hydrochloric acid and accordingly solution pH. Contact angle measurements and atomic force microscopy experiments determined that acid treatment increases surface hydrophilicity and porosity. X-ray photoelectron spectroscopy experiments identified that film etching is primarily caused by dissolution of indium species. A kinetic model was developed to explain the acid-catalyzed dissolution of ITO surfaces, and showed a logarithmic relationship between the rate of dissolution and the concentration of undisassociated hydrochloric acid molecules. Taken together, the findings presented in this work verify the acid-catalyzed kinetics of ITO film dissolution by chemical treatment, and support that the corresponding chemical reactions should be accounted for in ITO film processing applications. - Highlights: • Acidic conditions promoted indium tin oxide (ITO) film etching via dissolution. • Logarithm of the dissolution rate depended linearly on the solution pH. • Acid treatment increased ITO surface hydrophilicity and porosity. • ITO film etching led to preferential dissolution of indium species over tin species.

Amperometric titration of indium with edta solution in propanol

International Nuclear Information System (INIS)

Gevorgyan, A.M.; Talipov, Sh.T.; Khadeev, V.A.; Kostylev, V.S.; Khadeeva, L.A.

1980-01-01

Optimum conditions have been chosen for titration of indium with EDTA solution in anhydrous propanol and its mixtures with some aprotic solvents using amperometric and point detection. A procedure is suggested of determining indium microcontents in the presence of large amounts of other elements. The procedure is based on its extraction preseparation followed by direct titration in the extract with a standard EDTA solution [ru

Regularly arranged indium islands on glass/molybdenum substrates upon femtosecond laser and physical vapor deposition processing

Energy Technology Data Exchange (ETDEWEB)

Ringleb, F.; Eylers, K.; Teubner, Th.; Boeck, T., E-mail: torsten.boeck@ikz-berlin.de [Leibniz-Institute for Crystal Growth, Max-Born-Straße 2, Berlin 12489 (Germany); Symietz, C.; Bonse, J.; Andree, S.; Krüger, J. [Bundesanstalt für Materialforschung und-prüfung (BAM), Unter den Eichen 87, Berlin 12205 (Germany); Heidmann, B.; Schmid, M. [Department of Physics, Freie Universität Berlin, Arnimalle 14, Berlin 14195 (Germany); Nanooptical Concepts for PV, Helmholtz Zentrum Berlin, Hahn-Meitner-Platz 1, Berlin 14109 (Germany); Lux-Steiner, M. [Nanooptical Concepts for PV, Helmholtz Zentrum Berlin, Hahn-Meitner-Platz 1, Berlin 14109 (Germany); Heterogeneous Material Systems, Helmholtz Zentrum Berlin, Hahn-Meitner-Platz 1, Berlin 14109 (Germany)

2016-03-14

A bottom-up approach is presented for the production of arrays of indium islands on a molybdenum layer on glass, which can serve as micro-sized precursors for indium compounds such as copper-indium-gallium-diselenide used in photovoltaics. Femtosecond laser ablation of glass and a subsequent deposition of a molybdenum film or direct laser processing of the molybdenum film both allow the preferential nucleation and growth of indium islands at the predefined locations in a following indium-based physical vapor deposition (PVD) process. A proper choice of laser and deposition parameters ensures the controlled growth of indium islands exclusively at the laser ablated spots. Based on a statistical analysis, these results are compared to the non-structured molybdenum surface, leading to randomly grown indium islands after PVD.

Influence of nitrogen on magnetic properties of indium oxide

Science.gov (United States)

Ashok, Vishal Dev; De, S. K.

2013-07-01

Magnetic properties of indium oxide (In2O3) prepared by the decomposition of indium nitrate/indium hydroxide in the presence of ammonium chloride (NH4Cl) has been investigated. Structural and optical characterizations confirm that nitrogen is incorporated into In2O3. Magnetization has been convoluted to individual diamagnetic paramagnetic and ferromagnetic contributions with varying concentration of NH4Cl. Spin wave with diverging thermal exponent dominates in both field cool and zero field cool magnetizations. Uniaxial anisotropy plays an important role in magnetization as a function of magnetic field at higher concentration of NH4Cl. Avrami analysis indicates the absence of pinning effect in the magnetization process. Ferromagnetism has been interpreted in terms of local moments induced by anion dopant and strong hybridization with host cation.

Influence of nitrogen on magnetic properties of indium oxide

International Nuclear Information System (INIS)

Ashok, Vishal Dev; De, S K

2013-01-01

Magnetic properties of indium oxide (In 2 O 3 ) prepared by the decomposition of indium nitrate/indium hydroxide in the presence of ammonium chloride (NH 4 Cl) has been investigated. Structural and optical characterizations confirm that nitrogen is incorporated into In 2 O 3 . Magnetization has been convoluted to individual diamagnetic paramagnetic and ferromagnetic contributions with varying concentration of NH 4 Cl. Spin wave with diverging thermal exponent dominates in both field cool and zero field cool magnetizations. Uniaxial anisotropy plays an important role in magnetization as a function of magnetic field at higher concentration of NH 4 Cl. Avrami analysis indicates the absence of pinning effect in the magnetization process. Ferromagnetism has been interpreted in terms of local moments induced by anion dopant and strong hybridization with host cation. (paper)

Research on the effect of alkali roasting of copper dross on leaching rate of indium

Science.gov (United States)

Dafang, Liu; Fan, Xingxiang; Shi, Yifeng; Yang, Kunbin

2017-11-01

The byproduct copper dross produced during refining crude lead was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and fluorescence spectrometer (XRF), which showed that copper dross mainly contained lead, copper, zinc, arsenic, antimony, bismuth, sulfur and a small amount of indium and silver etc. The mineralogical phase change of oxidation roasting of copper dross by adding sodium hydroxide was analyzed with the help of XRD and SEM. The effects of water leaching, ratio of sodium hydroxide, roasting time, and roasting temperature on leaching rate of indium were investigated mainly. The experimental results showed that phase of lead metal and sulfides of lead, copper and zinc disappeared after oxidation roasting of copper dross by adding sodium hydroxide, new phase of oxides of lead, copper, zinc and sodium salt of arsenic and antimony appeared. Water leaching could remove arsenic, and acid leaching residue obtained was then leached with acid. The leaching rate of indium was higher 6.98% compared with alkali roasting of copper dross-acid leaching. It showed that removing arsenic by water leaching and acid leaching could increase the leaching rate of indium and be beneficial to reducing subsequent acid consumption of extracting indium by acid leaching. The roasting temperature had a significant effect on the leaching rate of indium, and leaching rate of indium increased with the rise of roasting temperature. When roasting temperature ranged from 450°C to 600°C, leaching rate of indium increased significantly with the rise of roasting temperature. When roasting temperature rose from 450°C to 600°C, leaching rate of indium increased by 60.29%. The amount of sodium hydroxide had an significant effect on the leaching rate of indium, and the leaching of indium increased with the increase of the amount of sodium hydroxide, and the leaching rate of indium was obviously higher than that of copper dross blank roasting and acid leaching.

Aluminium, gallium, indium and thallium

International Nuclear Information System (INIS)

Brown, Paul L.; Ekberg, Christian

2016-01-01

Aluminium can exist in a number of oxyhydroxide mineral phases including corundum, diaspore, boehmite and gibbsite. The stability constants at zero ionic strength reported for Al(OH) 3 (aq) vary linearly with respect to the inverse of absolute temperature. A full suite of thermodynamic parameters is available for all aluminium phases and hydrolysis species. Gallium hydrolyses to a greater extent than aluminium, with the onset of hydrolysis reactions occurring just above a pHof 1. In fact, even though aluminium has the smallest ionic radius of this series of metals, it has the weakest hydrolysis species and oxide/hydroxide phases.This is due to the presence of stabilising d-orbitals in the heavier metals, gallium, indium and thallium(III). There are few available data for the stability constants of indium(III) hydrolysis species. Of those that are available, the range in the proposed stability constants covers many orders of magnitude.

Short-range order in amorphous thin films of indium selenides

International Nuclear Information System (INIS)

Zakharov, V.P.; Poltavtsev, Yu.G.; Sheremet, G.P.

1982-01-01

A structure of the short-range order and a character of interatomic interactions in indium selenides Insub(1-x)Sesub(x) with 0.333 <= x <= 0.75, obtained in the form of amorphous films 0.05-0.80 μm thick are studied using electron diffraction method. It is found out that mostly tetrahedrical coordination of nearest neighbours in the vicinity of indium atoms is characteristic for studied amorphous films, and coordination of selenium atoms is different. Amorphous film with x=0.75 posesses a considereably microheterogeneous structure of the short-range order, which is characterized by the presence of microunclusions of amorphous selenium and atoms of indium, octohedrically coordinated by selenium atoms

Hydrothermal synthesis of two layered indium oxalates with 12-membered apertures

International Nuclear Information System (INIS)

Chen Zhenxia; Zhou Yaming; Weng Linhong; Zhang Haoyu; Zhao Dongyuan

2003-01-01

Two layered indium oxalates, In(C 2 O 4 ) 2.5 (C 3 N 2 H 12 )(H 2 O) 3 , I, and In(C 2 O 4 ) 1.5 (H 2 O) 3 , II, have been hydrothermally synthesized. In I, the linkage between indium and oxalate units gives rise to a sheet with a rectangular 12-membered aperture (six indium atoms and six oxalate units). Indium atom of II has an unusual pentagonal bipyramidal coordination arrangement. The connectivity between indium and oxalate units forms a neutral puckered layer with 12- (along a-axis) and eight-membered (along b-axis) apertures. Crystal data for these two indium oxalates are as follows: I, triclinic, space group: P-1 (No. 2), a=8.725(3) A, b=9.170(3) A, c=9.901(3) A, α=98.101(4) deg. , β=97.068(4) deg. , γ=102.403(4) deg. , V=756.3(4) A 3 , Z=2, M=463.0(5), ρ calc =2.042 g/cm 3 , R 1 =0.0377, wR 2 =0.0834. II, monoclinic, space group: P2 1 /c (No. 14), a=10.203(5) A, b=6.638(1) A, c=11.152(7) A, β=95.649(4) deg. , V=751.7(4)A 3 , Z=4, M=300.9(0), ρ calc =2.659 g/cm 3 , R 1 =0.0229, wR 2 =0.0488. TG analyses indicate the water molecules of I can be removed at 150 deg. C. The dehydrated product retains structural integrity

Highly conducting and transparent sprayed indium tin oxide

Energy Technology Data Exchange (ETDEWEB)

Rami, M.; Benamar, E.; Messaoudi, C.; Sayah, D.; Ennaoui, A. (Faculte des Sciences, Rabat (Morocco). Lab. de Physique des Materiaux)

1998-03-01

Indium tin oxide (ITO) has a wide range of applications in solar cells (e.g. by controlling the resistivity, we can use low conductivity ITO as buffer layer and highly conducting ITO as front contact in thin films CuInS[sub 2] and CuInSe[sub 2] based solar cells) due to its wide band gap (sufficient to be transparent) in both visible and near infrared range, and high carrier concentrations with metallic conduction. A variety of deposition techniques such as reactive electron beam evaporation, DC magnetron sputtering, evaporation, reactive thermal deposition, and spray pyrolysis have been used for the preparation of undoped and tin doped indium oxide. This latter process which makes possible the preparation of large area coatings has attracted considerable attention due to its simplicity and large scale with low cost fabrication. It has been used here to deposit highly transparent and conducting films of tin doped indium oxide onto glass substrates. The electrical, optical and structural properties have been investigated as a function of various deposition parameters namely dopant concentrations, temperature and nature of substrates. X-ray diffraction patterns have shown that deposited films are polycrystalline without second phases and have preferred orientation [400]. INdium tin oxide layers with small resistivity value around 7.10[sup -5] [omega].cm and transmission coefficient in the visible and near IR range of about 85-90% have been easily obtained. (authors) 13 refs.

The precipitation of indium at elevated pH in a stream influenced by acid mine drainage

Science.gov (United States)

White, Sarah Jane O.; Hussain, Fatima A.; Hemond, Harold F.; Sacco, Sarah A.; Shine, James P.; Runkel, Robert L.; Walton-Day, Katherine; Kimball, Briant A.

2017-01-01

Indium is an increasingly important metal in semiconductors and electronics and has uses in important energy technologies such as photovoltaic cells and light-emitting diodes (LEDs). One significant flux of indium to the environment is from lead, zinc, copper, and tin mining and smelting, but little is known about its aqueous behavior after it is mobilized. In this study, we use Mineral Creek, a headwater stream in southwestern Colorado severely affected by heavy metal contamination as a result of acid mine drainage, as a natural laboratory to study the aqueous behavior of indium. At the existing pH of ~ 3, indium concentrations are 6–29 μg/L (10,000 × those found in natural rivers), and are completely filterable through a 0.45 μm filter. During a pH modification experiment, the pH of the system was raised to > 8, and > 99% of the indium became associated with the suspended solid phase (i.e. does not pass through a 0.45 μm filter). To determine the mechanism of removal of indium from the filterable and likely primarily dissolved phase, we conducted laboratory experiments to determine an upper bound for a sorption constant to iron oxides, and used this, along with other published thermodynamic constants, to model the partitioning of indium in Mineral Creek. Modeling results suggest that the removal of indium from the filterable phase is consistent with precipitation of indium hydroxide from a dissolved phase. This work demonstrates that nonferrous mining processes can be a significant source of indium to the environment, and provides critical information about the aqueous behavior of indium.

Concerted Electrodeposition and Alloying of Antimony on Indium Electrodes for Selective Formation of Crystalline Indium Antimonide.

Science.gov (United States)

Fahrenkrug, Eli; Rafson, Jessica; Lancaster, Mitchell; Maldonado, Stephen

2017-09-19

The direct preparation of crystalline indium antimonide (InSb) by the electrodeposition of antimony (Sb) onto indium (In) working electrodes has been demonstrated. When Sb is electrodeposited from dilute aqueous electrolytes containing dissolved Sb 2 O 3 , an alloying reaction is possible between Sb and In if any surface oxide films are first thoroughly removed from the electrode. The presented Raman spectra detail the interplay between the formation of crystalline InSb and the accumulation of Sb as either amorphous or crystalline aggregates on the electrode surface as a function of time, temperature, potential, and electrolyte composition. Electron and optical microscopies confirm that under a range of conditions, the preparation of a uniform and phase-pure InSb film is possible. The cumulative results highlight this methodology as a simple yet potent strategy for the synthesis of intermetallic compounds of interest.

Properties of polycrystalline indium oxide in open air and in vacuum

International Nuclear Information System (INIS)

Solov'eva, A.E.; Zhdanov, V.A.; Markov, V.L.; Shvangiradze, R.R.

1982-01-01

Properties of polycrystalline indium oxide according to annealing temperature in open air and in vacuum are investigated. It is established that the indium oxide begins to change its chemical composition during the annealing in the open air from 1200 deg C, and in the vacuum - form 800 deg C. During the annealing of the samples in ths open air in the temperature range of 1200-1450 deg C the lattice of the indium oxide loses probably, only oxygen; this process is accompanied by change of the samples color, electrophysical properties, lattice parameter density. Cation sublattice is disturbed in the vacuum beginning from 900 deg C, which is accompanied by destruction of the color centers. X-ray density and the activation energy of the reduction accounting the formation of the color centers are calculated on the base of the X-ray data and the deviation from stoichiometry of the indium oxide depending on the annealing temperature in the open air

Supramolecular compounds of indium sulfates with nitrogen-containing cations

International Nuclear Information System (INIS)

Petrosyants, S.P.; Ilyukhin, A.B.; Ketsko, V.A.

2006-01-01

Compounds with a general formula [Cat][In(H 2 O) n (SO 4 ) 2 ] x · mH 2 O (where Cat = C(NH 2 ) 3 , H(2,2'-Bipy), H 2 (4,4'-Bipy), H 2 [Py(CH 2 ) 3 Py], and H 3 N(CH 2 ) 6 NH 3 ) were synthesized and identified from the elemental analysis, IR, and thermogravimetric analysis data. X-ray diffraction analysis of crystalline [C(NH 2 ) 3 ][In(H 2 O) 2 (SO 4 ) 2 ] complex has shown that the polymer chains of In aqua sulfate form ensembles with guanidinium ions. The structure of [H 2 (4,4'-Bipy)][In 2 (H 2 O) 6 (SO 4 ) 4 ] · 2H 2 O consists of the dimeric anions of indium sulfate. The coordination sphere of In includes three O atoms of three SO 4 groups and three O atoms of water molecules. The dimers are united into framework by diprotonated Bipy cations [ru

Studies on high electronic energy deposition in transparent conducting indium tin oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Deshpande, N G [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India); Gudage, Y G [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India); Ghosh, A [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India); Vyas, J C [Technical and Prototype Engineering Division, Bhabha Atomic Research Center, Trombay, Mumbai (MS) (India); Singh, F [Inter-University Accelerator Center, Aruna Asaf Ali Marg, Post Box 10502, New Delhi 110067 (India); Tripathi, A [Inter-University Accelerator Center, Aruna Asaf Ali Marg, Post Box 10502, New Delhi 110067 (India); Sharma, Ramphal [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India)

2008-02-07

We have examined the effect of swift heavy ions using 100 MeV Au{sup 8+} ions on the electrical properties of transparent, conducting indium tin oxide polycrystalline films with resistivity of 0.58 x 10{sup -4} {omega} cm and optical transmission greater than 78% (pristine). We report on the modifications occurring after high electronic energy deposition. With the increase in fluency, x-ray line intensity of the peaks corresponding to the planes (1 1 0), (4 0 0), (4 4 1) increased, while (3 3 1) remained constant. Surface morphological studies showed a pomegranate structure of pristine samples, which was highly disturbed with a high dose of irradiation. For the high dose, there was a formation of small spherical domes uniformly distributed over the entire surface. The transmittance was seen to be decreasing with the increase in ion fluency. At higher doses, the resistivity and photoluminescence intensity was seen to be decreased. In addition, the carrier concentration was seen to be increased, which was in accordance with the decrease in resistivity. The observed modifications after high electronic energy deposition in these films may lead to fruitful device applications.

Studies on high electronic energy deposition in transparent conducting indium tin oxide thin films

International Nuclear Information System (INIS)

Deshpande, N G; Gudage, Y G; Ghosh, A; Vyas, J C; Singh, F; Tripathi, A; Sharma, Ramphal

2008-01-01

We have examined the effect of swift heavy ions using 100 MeV Au 8+ ions on the electrical properties of transparent, conducting indium tin oxide polycrystalline films with resistivity of 0.58 x 10 -4 Ω cm and optical transmission greater than 78% (pristine). We report on the modifications occurring after high electronic energy deposition. With the increase in fluency, x-ray line intensity of the peaks corresponding to the planes (1 1 0), (4 0 0), (4 4 1) increased, while (3 3 1) remained constant. Surface morphological studies showed a pomegranate structure of pristine samples, which was highly disturbed with a high dose of irradiation. For the high dose, there was a formation of small spherical domes uniformly distributed over the entire surface. The transmittance was seen to be decreasing with the increase in ion fluency. At higher doses, the resistivity and photoluminescence intensity was seen to be decreased. In addition, the carrier concentration was seen to be increased, which was in accordance with the decrease in resistivity. The observed modifications after high electronic energy deposition in these films may lead to fruitful device applications

State of rare earth impurities in gallium and indium antimonides

International Nuclear Information System (INIS)

Evgen'ev, S.B.; Kuz'micheva, G.M.

1990-01-01

State of rare earth impurities in indium and gallium antimonides was studied. Results of measuring density and lattice parameter of samples in GaSb-rare earth and InSb-rare earth systems are presented. It is shown that during rare earth dissolution in indium and gallium antimonides rare earth atoms occupy interstitial positions or, at least, are displaced from lattice points

Synthesis of Novel Polymeric Resins by Gamma Irradiation for Separation of In(III) ions from Cd(II) in Aqueous Media

International Nuclear Information System (INIS)

Massoud, A.; Abou El-Nour, F.; Killa, H.

2012-01-01

In this work, Zn(II)polymethacrylates and poly(acrylamide-acrylic acid) were prepared by gamma irradiation polymerization technique of the corresponding monomer at 30 kGy. The polymeric resins were mixed with Indium ions to determine its capacity in aqueous solutions using batch experiment. The adsorption efficiency of obtained polymeric resins toward In(III) and Cd(II) in different experimental conditions was established. Batch and column methods were applied for separation of indium and cadmium. The effects of various eluants such as H 2 SO 4 , NH 4 NO 3 , HNO 3 and HCl on the recovery of both metal ions were studied. The polymeric resins may be regenerated using 3M HCl solutions.

Determination of gold and indium in sea water by neutron activation analysis

International Nuclear Information System (INIS)

Tateno, Yukio; Ohta, Naoichi

1979-01-01

A combination of electrodeposition on graphite with neutron activation analysis was used for the determination of gold and indium in sea water. At a potential of -0.70 V vs. the silver-silver chloride electrode, gold and indium were electrolyzed on to a graphite electrode (1.1 cm phi x 0.2 cm) from 100 ml of 0.5 M sodium chloride. Recovery yield of gold was constant at pH from 1 to 3 and was independent of the initial concentration of gold, (0.01 -- 1) ppb. For a 72-h electrolysis at pH 2 the recovery yield of gold was 92%, while that of indium was 32%. The graphite electrode was exposed to a thermal neutron flux of 5.1 x 10 11 or 1.5 x 10 12 n cm -2 s -1 : 5 min exposure for indium and 6 to 12 h for gold. After appropriate decay periods the activities of 198 Au and sup(116m)In were measured for 2000 s and 300 s, respectively, with a 4000-channel pulse-height analyser and a Ge(Li) detector. The total amount of gold in 1 l of a sea water sample (Tokyo Bay) was (0.023 +- 0.001)μg, in which nonelectrolyzable gold was estimated to be 0.005 μg. Indium concentration in the sample was too low to be determined by the present method. Detection limit for indium was 1 ppb. (author)

Plasma Treatment to Remove Carbon from Indium UV Filters

Science.gov (United States)

Greer, Harold F.; Nikzad, Shouleh; Beasley, Matthew; Gantner, Brennan

2012-01-01

The sounding rocket experiment FIRE (Far-ultraviolet Imaging Rocket Experiment) will improve the science community fs ability to image a spectral region hitherto unexplored astronomically. The imaging band of FIRE (.900 to 1,100 Angstroms) will help fill the current wavelength imaging observation hole existing from approximately equal to 620 Angstroms to the GALEX band near 1,350 Angstroms. FIRE is a single-optic prime focus telescope with a 1.75-m focal length. The bandpass of 900 to 1100 Angstroms is set by a combination of the mirror coating, the indium filter in front of the detector, and the salt coating on the front of the detector fs microchannel plates. Critical to this is the indium filter that must reduce the flux from Lymanalpha at 1,216 Angstroms by a minimum factor of 10(exp -4). The cost of this Lyman-alpha removal is that the filter is not fully transparent at the desired wavelengths of 900 to 1,100 Angstroms. Recently, in a project to improve the performance of optical and solar blind detectors, JPL developed a plasma process capable of removing carbon contamination from indium metal. In this work, a low-power, low-temperature hydrogen plasma reacts with the carbon contaminants in the indium to form methane, but leaves the indium metal surface undisturbed. This process was recently tested in a proof-of-concept experiment with a filter provided by the University of Colorado. This initial test on a test filter showed improvement in transmission from 7 to 9 percent near 900 with no process optimization applied. Further improvements in this performance were readily achieved to bring the total transmission to 12% with optimization to JPL's existing process.

Plasma vapor deposited n-indium tin oxide/p-copper indium oxide heterojunctions for optoelectronic device applications

Science.gov (United States)

Jaya, T. P.; Pradyumnan, P. P.

2017-12-01

Transparent crystalline n-indium tin oxide/p-copper indium oxide diode structures were fabricated on quartz substrates by plasma vapor deposition using radio frequency (RF) magnetron sputtering. The p-n heterojunction diodes were highly transparent in the visible region and exhibited rectifying current-voltage (I-V) characteristics with a good ideality factor. The sputter power during fabrication of the p-layer was found to have a profound effect on I-V characteristics, and the diode with the p-type layer deposited at a maximum power of 200 W exhibited the highest value of the diode ideality factor (η value) of 2.162, which suggests its potential use in optoelectronic applications. The ratio of forward current to reverse current exceeded 80 within the range of applied voltages of -1.5 to +1.5 V in all cases. The diode structure possessed an optical transmission of 60-70% in the visible region.

Indium oxide octahedrons based on sol–gel process enhance room temperature gas sensing performance

Energy Technology Data Exchange (ETDEWEB)

Mu, Xiaohui [Key Laboratory of Chemical Sensing & Analysis in Universities of Shandong, School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022, Shandong (China); Chen, Changlong, E-mail: chem.chencl@hotmail.com [Key Laboratory of Chemical Sensing & Analysis in Universities of Shandong, School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022, Shandong (China); Han, Liuyuan [Key Laboratory of Chemical Sensing & Analysis in Universities of Shandong, School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022, Shandong (China); Shao, Baiqi [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Wei, Yuling [Instrumental Analysis Center, Qilu University of Technology, Jinan 250353, Shandong (China); Liu, Qinglong; Zhu, Peihua [Key Laboratory of Chemical Sensing & Analysis in Universities of Shandong, School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022, Shandong (China)

2015-07-15

Highlights: • In{sub 2}O{sub 3} octahedron films are prepared based on sol–gel technique for the first time. • The preparation possesses merits of low temperature, catalyst-free and large production. • It was found that the spin-coating process in film fabrication was key to achieve the octahedrons. • The In{sub 2}O{sub 3} octahedrons could significantly enhance room temperature NO{sub 2} gas sensing performance. - Abstract: Indium oxide octahedrons were prepared on glass substrates through a mild route based on sol–gel technique. The preparation possesses characteristics including low temperature, catalyst-free and large production, which is much distinguished from the chemical-vapor-deposition based methods that usually applied to prepare indium oxide octahedrons. Detailed characterization revealed that the indium oxide octahedrons were single crystalline, with {1 1 1} crystal facets exposed. It was found that the spin-coating technique was key for achieving the indium oxide crystals with octahedron morphology. The probable formation mechanism of the indium oxide octahedrons was proposed based on the experiment results. Room temperature NO{sub 2} gas sensing measurements exhibited that the indium oxide octahedrons could significantly enhance the sensing performance in comparison with the plate-like indium oxide particles that prepared from the dip-coated gel films, which was attributed to the abundant sharp edges and tips as well as the special {1 1 1} crystal facets exposed that the former possessed. Such a simple wet-chemical based method to prepare indium oxide octahedrons with large-scale production is promising to provide the advanced materials that can be applied in wide fields like gas sensing, solar energy conversion, field emission, and so on.

Indium oxide octahedrons based on sol–gel process enhance room temperature gas sensing performance

International Nuclear Information System (INIS)

Mu, Xiaohui; Chen, Changlong; Han, Liuyuan; Shao, Baiqi; Wei, Yuling; Liu, Qinglong; Zhu, Peihua

2015-01-01

Highlights: • In 2 O 3 octahedron films are prepared based on sol–gel technique for the first time. • The preparation possesses merits of low temperature, catalyst-free and large production. • It was found that the spin-coating process in film fabrication was key to achieve the octahedrons. • The In 2 O 3 octahedrons could significantly enhance room temperature NO 2 gas sensing performance. - Abstract: Indium oxide octahedrons were prepared on glass substrates through a mild route based on sol–gel technique. The preparation possesses characteristics including low temperature, catalyst-free and large production, which is much distinguished from the chemical-vapor-deposition based methods that usually applied to prepare indium oxide octahedrons. Detailed characterization revealed that the indium oxide octahedrons were single crystalline, with {1 1 1} crystal facets exposed. It was found that the spin-coating technique was key for achieving the indium oxide crystals with octahedron morphology. The probable formation mechanism of the indium oxide octahedrons was proposed based on the experiment results. Room temperature NO 2 gas sensing measurements exhibited that the indium oxide octahedrons could significantly enhance the sensing performance in comparison with the plate-like indium oxide particles that prepared from the dip-coated gel films, which was attributed to the abundant sharp edges and tips as well as the special {1 1 1} crystal facets exposed that the former possessed. Such a simple wet-chemical based method to prepare indium oxide octahedrons with large-scale production is promising to provide the advanced materials that can be applied in wide fields like gas sensing, solar energy conversion, field emission, and so on

Thermopower of dilute alloys of indium

International Nuclear Information System (INIS)

Dudenhoeffer, A.W.

1974-01-01

An experimental investigation of a new theory of electron-diffusion thermopower is discussed. A figure of merit for this ''Nielsen--Taylor'' theory in various metals is established, and it indicates that the effect should be largest in lead, indium, thallium, and aluminum, in that order. Previous investigations have been carried out for lead and aluminum. The thermopower of indium (or any metal) changes when impurity scattering centers are introduced into it. This change in the thermopower as a function of temperature is analyzed in terms of the Nielsen--Taylor theory and in terms of the competing process known as ''phonon drag.'' Definite conclusions as to the validity of the new theory are hampered by the complex nature of this phonon drag, but the experimental data is consistent with the Nielsen--Taylor theory. (Diss. Abstr. Int., B)

Discovery of the calcium, indium, tin, and platinum isotopes

International Nuclear Information System (INIS)

Amos, S.; Gross, J.L.; Thoennessen, M.

2011-01-01

Currently, twenty-four calcium, thirty-eight indium, thirty-eight tin, and thirty-nine platinum isotopes have been observed and the discovery of these isotopes is discussed here. For each isotope a brief synopsis of the first refereed publication, including the production and identification method, is presented. - Highlights: Documentation of the discovery of all calcium, indium, tin and platinum isotopes. → Summary of author, journal, year, place and country of discovery for each isotope. → Brief description of discovery history of each isotope.

Electronic structure of indium-tungsten-oxide alloys and their energy band alignment at the heterojunction to crystalline silicon

Science.gov (United States)

Menzel, Dorothee; Mews, Mathias; Rech, Bernd; Korte, Lars

2018-01-01

The electronic structure of thermally co-evaporated indium-tungsten-oxide films is investigated. The stoichiometry is varied from pure tungsten oxide to pure indium oxide, and the band alignment at the indium-tungsten-oxide/crystalline silicon heterointerface is monitored. Using in-system photoelectron spectroscopy, optical spectroscopy, and surface photovoltage measurements, we show that the work function of indium-tungsten-oxide continuously decreases from 6.3 eV for tungsten oxide to 4.3 eV for indium oxide, with a concomitant decrease in the band bending at the hetero interface to crystalline silicon than indium oxide.

Development of an Indium Bump Bond Process for Silicon Pixel Detectors at PSI

CERN Document Server

Brönnimann, C; Gobrecht, J; Heising, S; Horisberger, M; Horisberger, R P; Kästli, H C; Lehmann, J; Rohe, T; Streuli, S; Broennimann, Ch.

2006-01-01

The hybrid pixel detectors used in the high energy physics experiments currently under construction use a three dimensional connection technique, the so-called bump bonding. As the pitch below 100um, required in these applications, cannot be fullfilled with standard industrial processes (e.g. the IBM C4 process), an in-house bump bond process using reflown indium bumps was developed at PSI as part of the R&D for the CMS-pixel detector. The bump deposition on the sensor is performed in two subsequent lift-off steps. As the first photolithographic step a thin under bump metalization (UBM) is sputtered onto bump pads. It is wettable by indium and defines the diameter of the bump. The indium is evaporated via a second photolithographic step with larger openings and is reflown afterwards. The height of the balls is defined by the volume of the indium. On the readout chip only one photolithographic step is carried out to deposit the UBM and a thin indium layer for better adhesion. After mating both parts a seco...

Effect of indium addition in U-Zr metallic fuel on lanthanide migration

Energy Technology Data Exchange (ETDEWEB)

Kim, Yeon Soo, E-mail: yskim@anl.gov [Argonne National Laboratory, 9700 S. Cass Ave, Argonne, IL 60439 (United States); Wiencek, T.; O' Hare, E.; Fortner, J.; Wright, A. [Argonne National Laboratory, 9700 S. Cass Ave, Argonne, IL 60439 (United States); Cheon, J.S.; Lee, B.O. [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseong-gu, Daejeon 305-353 (Korea, Republic of)

2017-02-15

Advanced fast reactor concepts to achieve ultra-high burnup (∼50%) require prevention of fuel-cladding chemical interaction (FCCI). Fission product lanthanide accumulation at high burnup is substantial and significantly contributes to FCCI upon migration to the cladding interface. Diffusion barriers are typically used to prevent interaction of the lanthanides with the cladding. A more active method has been proposed which immobilizes the lanthanides through formation of stable compounds with an additive. Theoretical analysis showed that indium, thallium, and antimony are good candidates. Indium was the strongest candidate because of its low reactivity with iron-based cladding alloys. Characterization of the as-fabricated alloys was performed to determine the effectiveness of the indium addition in forming compounds with lanthanides, represented by cerium. Tests to examine how effectively the dopant prevents lanthanide migration under a thermal gradient were also performed. The results showed that indium effectively prevented cerium migration.

Effect of indium addition in U-Zr metallic fuel on lanthanide migration

Energy Technology Data Exchange (ETDEWEB)

Kim, Yeon Soo; Wiencek, T.; O' Hare, E.; Fortner, J.; Wright, A.; Cheon, J. S.; Lee, B. O.

2017-02-01

Advanced fast reactor concepts to achieve ultra-high burnup (~50%) require prevention of fuel-cladding chemical interaction (FCCI). Fission product lanthanide accumulation at high burnup is substantial and significantly contributes to FCCI upon migration to the cladding interface. Diffusion barriers are typically used to prevent interaction of the lanthanides with the cladding. A more active method has been proposed which immobilizes the lanthanides through formation of stable compounds with an additive. Theoretical analysis showed that indium, thallium, and antimony are good candidates. Indium was the strongest candidate because of its low reactivity with iron-based cladding alloys. Characterization of the as-fabricated alloys was performed to determine the effectiveness of the indium addition in forming compounds with lanthanides, represented by cerium. Tests to examine how effectively the dopant prevents lanthanide migration under a thermal gradient were also performed. The results showed that indium effectively prevented cerium migration.

Polyol-mediated synthesis of copper indium sulphide by solvothermal process

International Nuclear Information System (INIS)

Gorai, S.; Chaudhuri, S.

2005-01-01

A simple polyol-mediated solvothermal method has been proposed to synthesize copper indium sulphide. XRD studies reveal that the products are well crystallized. SEM indicates rod-like (with different aspect ratio) and star-shaped flake-like morphology of the products. The products are also characterized by optical studies and compositional analysis (XRF). XRF results show the formation of stoichiometric and non-stoichiometric copper indium sulphides depending on the reaction conditions

Calibration of differential scanning calorimeters: A comparison between indium and diphenylacetic acid

International Nuclear Information System (INIS)

Charsley, E.L.; Laye, P.G.; Markham, H.M.; Le Goff, T.

2010-01-01

The close proximity in melting temperature of the LGC Limited DSC standards indium and diphenylacetic acid, has enabled a direct assessment to be made of any differences resulting from the use of a metal or an organic compound in the calibration of DSC equipment. Following calibration with indium, the equilibrium fusion temperatures for diphenylacetic acid, were determined by both the stepwise heating and extrapolation to zero heating rate methods. The results were in excellent agreement with the certificate values and established that indium may be used as a calibrant when making accurate DSC measurements on organic materials in the same temperature range and that it has the advantage that it is non-volatile and can be used a number of times without significant change. Similar agreement was obtained in the measurement of the enthalpy of fusion, although the larger heat capacity change on fusion of diphenylacetic acid resulted in a greater uncertainty than with indium.

Interaction of cadmium and indium nitrate mixture with sodium tungstate in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Belousova, E E; Krivobok, V I; Gruba, A I [Donetskij Gosudarstvennyj Univ. (Ukrainian SSR)

1982-01-01

The interaction of the mixture of cadmium and indium nitrates with sodium tungstate in aqueous solution is studied using the methods of ''residual concentrations'', pH potentiometry and conductometry. Independent of the ratio of components in the initial solution a mixture of coprecipitated normal tungstates of cadmium and indium is formed in the system. Heat treatment of the precipitates at 800 deg C for 50 hrs with subsequent hardening results in the formation of solid solutions on the basis of normal cadmium and indium tungstates.

The angular distributions of sputtered indium atoms at different temperature

International Nuclear Information System (INIS)

Zhang Jiping; Wang Zhenxia; Tao Zhenlan; Pan Jisheng

1993-01-01

The effect of temperature and surface topography on the angular distribution of indium atoms was studied under bombardment by 2T KeV Ar + ions at normal incidence. Experiments were carried out on two samples, A and B, at 25 o C and 70 o C respectively. The function Y(θ) = a cosθ + b cos n θ, where θ is the sputtering angle, was found to fit the experimental data. The term (a cos θ) corresponds to the cosine distribution predicted by random collision cascade theory, and the term (b cos n θ) is dependent on factors such as the surface topography. For sample A, a∼b, whereas for sample B a< b. The surface of A consisted of flat and pebble like regions of almost equal area while the surface of B was more cratered. An explanation of the fitting values of a,b and n is given in terms of the shielding effects of the different structures. (UK)

Electronic and chemical properties of barium and indium clusters

International Nuclear Information System (INIS)

Onwuagba, B.N.

1992-11-01

The ground state electronic and chemical properties of divalent barium and trivalent indium are investigated in a self-consistent manner using the spin-polarized local density approximation in the framework of Density Functional Theory. A jellium model is adopted in the spirit of Gunnarsson and Lundqvist exchange and correlation energies and the calculated properties primarily associated with the s-p orbitals in barium and p orbitals in indium provide deepened insight towards the understanding of the mechanisms to the magic numbers in both clusters. (author). 21 refs, 5 figs

Activation analysis of indium used as tracer in hydrogeology

International Nuclear Information System (INIS)

Stanescu, S.P.; Farcasiu, O.M.; Gaspar, E.; Spiridon, S.; Nazarov, V.M.; Frontasieva, M.V.

1985-01-01

About 2500 samples of 18 hydro-karstic structures from Romania have been analyzed. The water flow rates were in the range of 0.05 to 2.7 m 3 /s and transit time values were from 30 h to 200 days. The quantity of indium used for a labelling was a calculated function of the emergency flow rate and the estimated transit time and varied from 1 to 100 g. The results prove that the activation analysis of indium in water samples combined with preconcentration by coprecipitation is an useful method in hydrogeological studies

Effect of Indium Doping on the Sensitivity of SnO2 Gas Sensor

International Nuclear Information System (INIS)

Suharni; Sayono

2009-01-01

The dependence of sensitivity f SnO 2 gas sensors on indium concentration has been studied. Undoped and indium-doped SnO 2 gas sensors have been prepared by DC sputtering technique with following parameters i.e : electrode voltage of 3 kV, current 20 mA, vacuum pressure 1.8 × 10 -1 torr, deposition time 60 minutes and temperature of 200℃. The effect of weight variations of indium in order of 0.0370; 0.0485 and 0.0702 grams into SnO 2 thin film gas sensor for optimum result were investigated. The measurement of resistance, sensitivity and response time for various temperature for detecting of carbon monoxide (CO), Ammonia (NH 3 ) and acetone (CH 3 COCH 3 ) gas for indium doped has been done. From the analysis result shows that for indium doped 0.0702 g on the SnO 2 the resistance can be decreased from 832.0 kΩ to 3.9 kΩ and the operating temperature from 200℃ to 90℃ and improving the sensitivity from 15.92% to 40.09% and a response time from 30 seconds to 10 seconds for CO. (author)

Optoelectronic properties of sprayed transparent and conducting indium doped zinc oxide thin films

International Nuclear Information System (INIS)

Shinde, S S; Shinde, P S; Bhosale, C H; Rajpure, K Y

2008-01-01

Indium doped zinc oxide (IZO) thin films are grown onto Corning glass substrates using the spray pyrolysis technique. The effect of doping concentration on the structural, electrical and optical properties of IZO thin films is studied. X-ray diffraction studies show a change in preferential orientation from the (0 0 2) to the (1 0 1) crystal planes with increase in indium doping concentration. Scanning electron microscopy studies show polycrystalline morphology of the films. Based on the Hall-effect measurements and analysis, impurity scattering is found to be the dominant mechanism determining the diminished mobility in ZnO thin films having higher indium concentration. The addition of indium also induces a drastic decrease in the electrical resistivity of films; the lowest resistivity (4.03 x 10 -5 Ω cm) being observed for the film deposited with 3 at% indium doping. The effect of annealing on the film properties has been reported. Films deposited with 3 at% In concentration have relatively low resistivity with 90% transmittance at 550 nm and the highest value of figure of merit 7.9 x 10 -2 □ Ω -1

Evaluation of indium-111 colloid for radionuclide imaging of the abdominal lymph nodes

International Nuclear Information System (INIS)

Vieras, F.; Hamilton, R.F.; Grissom, M.P.; Kiepffer, R.F.; Vandergrift, J.F.

1981-01-01

The experimental evaluation of indium-111 colloid for imaging the para-aortic lymph nodes in animals is described and preliminary results obtained in human subjects. Serial lymphatic scintigraphy performed in beagle dogs following bilateral pedal subcutaneous injections of indium-111 colloid revealed good para-aortic lymph node visualization. A normal migration pattern of indium-111 colloid was also observed in human subjects following subcutaneous injection in the feet; there was clear visualization of the ileo-inguinal and para-aortic lymph nodes. Organ distribution studies for indium-111 colloid were performed in rats following unilateral pedal subcutaneous injection in rats; these results were used for calculating radiation dose estimates to various organs. The study demonstrates the feasibility of using 111 In-colloid clinically for abdominal lymphatic scintiography for the use of sup(99m)Tc-labelled colloids results in lower radiation doses. (U.K.)

Gas chromatography of indium in macroscopic and carrier-free amounts using quartz and gold as stationary phases

Energy Technology Data Exchange (ETDEWEB)

Serov, A.; Eichler, R.; Tuerler, A.; Wittwer, D.; Gaeggeler, H.W. [Paul Scherrer Inst. (PSI), Villigen (Switzerland). Lab. fuer Radiochemie und Umweltchemie; Bern Univ. (Switzerland). Dept. fuer Chemie und Biochemie; Dressler, R.; Piguet, D.; Voegele, A. [Paul Scherrer Inst. (PSI), Villigen (Switzerland). Lab. fuer Radiochemie und Umweltchemie

2011-07-01

The chemical investigation of E113 is likely to become soon feasible. The determination of chemical properties of carrier-free amounts of the lighter homologues of element 113, especially indium and thallium, allows designing experimental set-ups and selecting experimental conditions suitable for performing these studies. Here, we present investigations of the interaction of indium species with quartz and gold surfaces. Deposition temperatures as well as enthalpies of adsorption were determined for indium T{sub dep} = 739 {+-} 20 C (-{delta}H{sub ads}(In) = 227 {+-} 10 kJ mol{sup -1}) and for indium hydroxide T{sub dep} = 250 {+-} 20 C (-{delta}H{sub ads}(InOH)= 124 {+-}10 kJ mol{sup -1}) respectively, on quartz. In case of adsorption of indium on a gold surface only a lower limit of the deposition temperature was established T{sub dep} > 980 C (-{delta}H{sub ads}(In) {>=} 315 {+-} 10 kJ mol{sup -1}). Investigations of macroscopic amounts of indium in thermosublimation experiments at similar experimental conditions were instrumental to establish a tentative speciation of the observed indium species. (orig.)

Room temperature deposition of crystalline indium tin oxide films by cesium-assisted magnetron sputtering

International Nuclear Information System (INIS)

Lee, Deuk Yeon; Baik, Hong-Koo

2008-01-01

Indium tin oxide (ITO) films were deposited on a Si (1 0 0) substrate at room temperature by cesium-assisted magnetron sputtering. Including plasma characteristics, the structural, electrical, and optical properties of deposited films were investigated as a function of cesium partial vapor pressure controlled by cesium reservoir temperature. We calculated the cesium coverage on the target surface showing maximum formation efficiency of negative ions by means of the theoretical model. Cesium addition promotes the formation efficiency of negative ions, which plays important role in enhancing the crystallinity of ITO films. In particular, the plasma density was linearly increased with cesium concentrations. The resultant decrease in specific resistivity and increase in transmittance (82% in the visible region) at optimum cesium concentration (4.24 x 10 -4 Ω cm at 80 deg. C of reservoir temperature) may be due to enhanced crystallinity of ITO films. Excess cesium incorporation into ITO films resulted in amorphization of its microstructure leading to degradation of ITO crystallinity. We discuss the cesium effects based on the growth mechanism of ITO films and the plasma density

Template synthesis of indium nanowires using anodic aluminum oxide membranes.

Science.gov (United States)

Chen, Feng; Kitai, Adrian H

2008-09-01

Indium nanowires with diameters approximately 300 nm have been synthesized by a hydraulic pressure technique using anodic aluminum oxide (AAO) templates. The indium melt is injected into the AAO template and solidified to form nanostructures. The nanowires are dense, continuous and uniformly run through the entire approximately 60 microm thickness of the AAO template. X-ray diffraction (XRD) reveals that the nanowires are polycrystalline with a preferred orientation. SEM is performed to characterize the morphology of the nanowires.

Indium oxide inverse opal films synthesized by structure replication method

Science.gov (United States)

Amrehn, Sabrina; Berghoff, Daniel; Nikitin, Andreas; Reichelt, Matthias; Wu, Xia; Meier, Torsten; Wagner, Thorsten

2016-04-01

We present the synthesis of indium oxide (In2O3) inverse opal films with photonic stop bands in the visible range by a structure replication method. Artificial opal films made of poly(methyl methacrylate) (PMMA) spheres are utilized as template. The opal films are deposited via sedimentation facilitated by ultrasonication, and then impregnated by indium nitrate solution, which is thermally converted to In2O3 after drying. The quality of the resulting inverse opal film depends on many parameters; in this study the water content of the indium nitrate/PMMA composite after drying is investigated. Comparison of the reflectance spectra recorded by vis-spectroscopy with simulated data shows a good agreement between the peak position and calculated stop band positions for the inverse opals. This synthesis is less complex and highly efficient compared to most other techniques and is suitable for use in many applications.

The steady-state and time-resolved photophysical properties of a dimeric indium phthalocyanine complex

International Nuclear Information System (INIS)

Chen Yu; Araki, Yasuyuki; Dini, Danilo; Liu Ying; Ito, Osamu; Fujitsuka, Mamoru

2006-01-01

The steady-state and time-resolved photophysical properties and some molecular orbital calculation results of a dimeric indium phthalocyanine complex with an indium-indium bond, i.e., [tBu 4 PcIn] 2 .2tmed, have been described. The results regarding triplet excited state lifetimes can be ascribed to strong intramolecular interactions existing only in the excited state of this dimer because no significant difference in the absorption spectra of the tBu 4 PcInCl monomer and the [tBu 4 PcIn] 2 .2tmed dimer is observed, suggesting that no ground-state interaction can be assessed. The deactivation processes of the excited singlet state of [tBu 4 PcIn] 2 .2tmed are apparently faster than that of μ-oxo-bridged PcIn dimer [tBu 4 PcIn] 2 O. Molecular orbital calculation on the PcIn dimer shows no node between two indium atoms was found in the HOMO - 2 of the PcIn-InPc dimer, suggesting that bonding electrons distribute between two indium atoms

Hydration of magnesia cubes: a helium ion microscopy study

Directory of Open Access Journals (Sweden)

Ruth Schwaiger

2016-02-01

Full Text Available Physisorbed water originating from exposure to the ambient can have a strong impact on the structure and chemistry of oxide nanomaterials. The effect can be particularly pronounced when these oxides are in physical contact with a solid substrate such as the ones used for immobilization to perform electron or ion microscopy imaging. We used helium ion microscopy (HIM and investigated morphological changes of vapor-phase-grown MgO cubes after vacuum annealing and pressing into foils of soft and high purity indium. The indium foils were either used as obtained or, for reference, subjected to vacuum drying. After four days of storage in the vacuum chamber of the microscope and at a base pressure of p −7 mbar, we observed on these cubic particles the attack of residual physisorbed water molecules from the indium substrate. As a result, thin magnesium hydroxide layers spontaneously grew, giving rise to characteristic volume expansion effects, which depended on the size of the particles. Rounding of the originally sharp cube edges leads to a significant loss of the morphological definition specific to the MgO cubes. Comparison of different regions within one sample before and after exposure to liquid water reveals different transformation processes, such as the formation of Mg(OH2 shells that act as diffusion barriers for MgO dissolution or the evolution of brucite nanosheets organized in characteristic flower-like microstructures. The findings underline the significant metastability of nanomaterials under both ambient and high-vacuum conditions and show the dramatic effect of ubiquitous water films during storage and characterization of oxide nanomaterials.

Nanostructured antistatic and antireflective thin films made of indium tin oxide and silica over-coat layer

Science.gov (United States)

Cho, Young-Sang; Hong, Jeong-Jin; Yang, Seung-Man; Choi, Chul-Jin

2010-08-01

Stable dispersion of colloidal indium tin oxide nanoparticles was prepared by using indium tin oxide nanopowder, organic solvent, and suitable dispersants through attrition process. Various comminution parameters during the attrition step were studied to optimize the process for the stable dispersion of indium tin oxide sol. The transparent and conductive films were fabricated on glass substrate using the indium tin oxide sol by spin coating process. To obtain antireflective function, partially hydrolyzed alkyl silicate was deposited as over-coat layer on the pre-fabricated indium tin oxide film by spin coating technique. This double-layered structure of the nanostructured film was characterized by measuring the surface resistance and reflectance spectrum in the visible wavelength region. The final film structure was enough to satisfy the TCO regulations for EMI shielding purposes.

Effects of target bias voltage on indium tin oxide films deposited by high target utilisation sputtering

International Nuclear Information System (INIS)

Calnan, Sonya; Upadhyaya, Hari M.; Dann, Sandra E.; Thwaites, Mike J.; Tiwari, Ayodhya N.

2007-01-01

Indium tin oxide (ITO) films were deposited by reactive High Target Utilisation Sputtering (HiTUS) onto glass and polyimide substrates. The ion plasma was generated by an RF power source while the target bias voltage was varied from 300 V to 500 V using a separate DC power supply. The deposition rate, at constant target power, increased with DC target voltage due to increased ion energy reaching 34 nm/min at 500 V. All the films were polycrystalline and showed strong (400) and (222) reflections with the relative strength of latter increasing with target bias voltage. The resistivity was lowest at 500 V with values of 1.8 x 10 -4 Ω cm and 2.4 x 10 -4 Ω cm on glass and polyimide, respectively but was still less than 5 x 10 -4 Ω cm at 400 V. All films were highly transparent to visible light, (> 80%) but the NIR transmittance decreased with increasing target voltage due to higher free carrier absorption. Therefore, ITO films can be deposited onto semiconductor layers such as in solar cells, with minimal ion damage while maintaining low resistivity

Pushing indium phosphide quantum dot emission deeper into the near infrared

Science.gov (United States)

Saeboe, A. M.; Kays, J.; Mahler, A. H.; Dennis, A. M.

2018-02-01

Cadmium-free near infrared (NIR) emitting quantum dots (QDs) have significant potential for multiplexed tissue-depth imaging applications in the first optical tissue window (i.e., 650 - 900 nm). Indium phosphide (InP) chemistry provides one of the more promising cadmium-free options for biomedical imaging, but the full tunability of this material has not yet been achieved. Specifically, InP QD emission has been tuned from 480 - 730 nm in previous literature reports, but examples of samples emitting from 730 nm to the InP bulk bandgap limit of 925 nm are lacking. We hypothesize that by generating inverted structures comprising ZnSe/InP/ZnS in a core/shell/shell heterostructure, optical emission from the InP shell can be tuned by changing the InP shell thickness, including pushing deeper into the NIR than current InP QDs. Colloidal synthesis methods including hot injection precipitation of the ZnSe core and a modified successive ion layer adsorption and reaction (SILAR) method for stepwise shell deposition were used to promote growth of core/shell/shell materials with varying thicknesses of the InP shell. By controlling the number of injections of indium and phosphorous precursor material, the emission peak was tuned from 515 nm to 845 nm (2.41 - 1.47 eV) with consistent full width half maximum (FWHM) values of the emission peak 0.32 eV. To confer water solubility, the nanoparticles were encapsulated in PEGylated phospholipid micelles, and multiplexing of NIR-emitting InP QDs was demonstrated using an IVIS imaging system. These materials show potential for multiplexed imaging of targeted QD contrast agents in the first optical tissue window.

Evolution of MBE HgCdTe defect structure studied with ion milling method

Directory of Open Access Journals (Sweden)

Pociask-Bialy Malgorzata

2017-01-01

Full Text Available In this paper, is shown how ion milling can assist in assessing the defect structure of MCT by revealing the residual doping, and establishing the minimum level of donor concentration Nmd, which is needed for obtaining n-regions with a reproducible n value. For this purpose, a study of the electrical properties of ion-milled LWIR n-type MCT films, un-doped and doped with indium with the concentration NIn = 5 × 1014–1017 cm−3 is proposed.

On the impact of indium distribution on the electronic properties in InGaN nanodisks

KAUST Repository

Benaissa, M.

2015-03-09

We analyze an epitaxially grown heterostructure composed of InGaN nanodisks inserted in GaN nanowires in order to relate indium concentration to the electronic properties. This study was achieved with spatially resolved low-loss electron energy-loss spectroscopy using monochromated electrons to probe optical excitations - plasmons - at nanometer scale. Our findings show that each nanowire has its own indium fluctuation and therefore its own average composition. Due to this indium distribution, a scatter is obtained in plasmon energies, and therefore in the optical dielectric function, of the nanowire ensemble. We suppose that these inhomogeneous electronic properties significantly alter band-to-band transitions and consequently induce emission broadening. In addition, the observation of tailing indium composition into the GaN barrier suggests a graded well-barrier interface leading to further inhomogeneous broadening of the electro-optical properties. An improvement in the indium incorporation during growth is therefore needed to narrow the emission linewidth of the presently studied heterostructures.

On the impact of indium distribution on the electronic properties in InGaN nanodisks

KAUST Repository

Benaissa, M.; Sigle, W.; Ng, Tien Khee; El Bouayadi, R.; van Aken, P. A.; Jahangir, S.; Bhattacharya, P.; Ooi, Boon S.

2015-01-01

We analyze an epitaxially grown heterostructure composed of InGaN nanodisks inserted in GaN nanowires in order to relate indium concentration to the electronic properties. This study was achieved with spatially resolved low-loss electron energy-loss spectroscopy using monochromated electrons to probe optical excitations - plasmons - at nanometer scale. Our findings show that each nanowire has its own indium fluctuation and therefore its own average composition. Due to this indium distribution, a scatter is obtained in plasmon energies, and therefore in the optical dielectric function, of the nanowire ensemble. We suppose that these inhomogeneous electronic properties significantly alter band-to-band transitions and consequently induce emission broadening. In addition, the observation of tailing indium composition into the GaN barrier suggests a graded well-barrier interface leading to further inhomogeneous broadening of the electro-optical properties. An improvement in the indium incorporation during growth is therefore needed to narrow the emission linewidth of the presently studied heterostructures.

Recalibration of indium foil for personnel screening in criticality accidents.

Science.gov (United States)

Takada, C; Tsujimura, N; Mikami, S

2011-03-01

At the Nuclear Fuel Cycle Engineering Laboratories of the Japan Atomic Energy Agency (JAEA), small pieces of indium foil incorporated into personal dosemeters have been used for personnel screening in criticality accidents. Irradiation tests of the badges were performed using the SILENE reactor to verify the calibration of the indium activation that had been made in the 1980s and to recalibrate them for simulated criticalities that would be the most likely to occur in the solution process line. In addition, Monte Carlo calculations of the indium activation using the badge model were also made to complement the spectral dependence. The results lead to a screening level of 15 kcpm being determined that corresponds to a total dose of 0.25 Gy, which is also applicable in posterior-anterior exposure. The recalibration based on the latest study will provide a sounder basis for the screening procedure in the event of a criticality accident.

Synthesis of indium nanoclusters and formation of thin film contacts on plastic substrates for organic and flexible electronics applications

International Nuclear Information System (INIS)

Shi, Frank F; Bulkowski, Michal; Hsieh, K C

2007-01-01

In this work, we described the processes of synthesizing free-standing indium nanoclusters using inverse micelles and microemulsions as well as synthesizing organic-encapsulated indium nanoclusters using alkanethiols as the organic encapsulants. The synthesized organic-encapsulated indium nanoclusters have demonstrated the feasibilities to be used as plastic compatible soft metal contacts for emerging organic devices. The homogeneously distributed indium nanoclusters with sizes of 10-30 nm have been fabricated on a few different plastic substrates. By changing the alkanethiol carbon chain length and the sizes of the indium nanoclusters, the annealing temperature required to form low-resistance indium thin film conductors has been reduced to 80-100 deg. C, which is acceptable for a variety of organic thin films

Investigation of an Electrochemical Method for Separation of Copper, Indium, and Gallium from Pretreated CIGS Solar Cell Waste Materials

Directory of Open Access Journals (Sweden)

Anna M. K. Gustafsson

2015-01-01

Full Text Available Recycling of the semiconductor material copper indium gallium diselenide (CIGS is important to ensure a future supply of indium and gallium, which are relatively rare and therefore expensive elements. As a continuation of our previous work, where we recycled high purity selenium from CIGS waste materials, we now show that copper and indium can be recycled by electrodeposition from hydrochloric acid solutions of dissolved selenium-depleted material. Suitable potentials for the reduction of copper and indium were determined to be −0.5 V and −0.9 V (versus the Ag/AgCl reference electrode, respectively, using cyclic voltammetry. Electrodeposition of first copper and then indium from a solution containing the dissolved residue from the selenium separation and ammonium chloride in 1 M HCl gave a copper yield of 100.1 ± 0.5% and an indium yield of 98.1 ± 2.5%. The separated copper and indium fractions contained no significant contamination of the other elements. Gallium remained in solution together with a small amount of indium after the separation of copper and indium and has to be recovered by an alternative method since electrowinning from the chloride-rich acid solution was not effective.

Formation of InN phase by sequential ion implantation

International Nuclear Information System (INIS)

Santhana Raman, P.; Ravichandran, V.; Nair, K.G.M.; Kesavamoorthy, R.; Kalavathi, S.; Panigrahi, B.K.; Dhara, S.

2006-01-01

Formation of InN phase by sequentially implanting nitrogen on indium implanted silica was demonstrated. The growth of embedded InN phase on as-implanted and post-implantation annealed sample was studied using Glancing Incidence X-Ray Diffraction (GIXRD) and Raman spectroscopy. Existence of both cubic and hexagonal phases of InN was observed. Results of irradiation induced ripening of In nanoclusters due to N + ion implantation was also studied. (author)

Diagnosis of infection by preoperative scintigraphy with indium-labeled white blood cells

International Nuclear Information System (INIS)

Wukich, D.K.; Abreu, S.H.; Callaghan, J.J.; Van Nostrand, D.; Savory, C.G.; Eggli, D.F.; Garcia, J.E.; Berrey, B.H.

1987-01-01

Scintigraphy with indium-labeled white blood cells has been reported to be sensitive and specific in the diagnosis of low-grade sepsis of the musculoskeletal system. We reviewed the records of fifty patients who had suspected osteomyelitis or suspected infection about a total joint prosthesis and who underwent scintigraphy with technetium-99m methylene diphosphonate and scintigraphy with indium-111 oxine-labeled white blood cells before an open surgical procedure. Any patient who received preoperative antibiotics was not included in the study. For all of the patients, gram-stain examination of smears, evaluation of a culture of material from the operative site, and histological examination were done. The patients were divided into two groups. Group I was composed of twenty-four patients, each of whom had a prosthesis in place and complained of pain. Group II was composed of twenty-six patients for whom a diagnosis of chronic osteomyelitis had to be considered. With the indium scans alone, there was only one false-negative result (in Group II), but there were eighteen false-positive results (eight patients in Group II and ten patients in Group I). Although scintigraphy with indium-labeled white blood cells is quite sensitive, it is not specific in detecting chronic osteomyelitis; a negative scan should be considered highly suggestive that osteomyelitis is not present. Specificity can be increased by interpreting the indium scan in conjunction with the technetium scan

Interaction of indium trichloride with calcium carbonate in aqueous solutions

International Nuclear Information System (INIS)

Kochetkova, N.V.; Toptygina, G.M.; Soklakova, O.V.; Evdokimov, V.I.

1991-01-01

Interaction of indium trichloride with calcium carbonate in aqueous solutions was studied, using methods of potentiometry, isothermal solubility and physicochemical computer simulating. The Gibb's energy value for crystal indium trihydroxide formation was calculated on the basis of experimental data on In(OH) 3 solubility. The value obtained was used for estimating equilibrium composition of InCl 3 -HCl-CaCO 3 -CO 2 -H 2 O system at a temperature of 25 deg C and carbon dioxide partial pressure of 0.05 to 1 at

Spectroscopic investigation of indium halides as substitudes of mercury in low pressure discharges for lighting applications

Energy Technology Data Exchange (ETDEWEB)

Briefi, Stefan

2012-05-22

Low pressure discharges with indium halides as radiator are discussed as substitutes for hazardous mercury in conventional fluorescent lamps. In this work, the applicability of InBr and InCl in a low pressure discharge light source is investigated. The aim is to identify and understand the physical processes which determine the discharge characteristics and the efficiency of the generated near-UV emission of the indium halide molecule and of the indium atom which is created due to dissociation processes in the plasma. As discharge vessels sealed cylindrical quartz glass tubes which contain a defined amount of indium halide and a rare gas are used. Preliminary investigations showed that for a controlled variation of the indium halide density a well-defined cold spot setup is mandatory. This was realized in the utilized experimental setup. The use of metal halides raises the issue, that power coupling by internal electrodes is not possible as the electrodes would quickly be eroded by the halides. The comparison of inductive and capacitive RF-coupling with external electrodes revealed that inductively coupled discharges provide higher light output and much better long term stability. Therefore, all investigations are carried out using inductive RF-coupling. The diagnostic methods optical emission and white light absorption spectroscopy are applied. As the effects of absorption-signal saturation and reabsorption of emitted radiation within the plasma volume could lead to an underestimation of the determined population densities by orders of magnitude, these effects are considered in the data evaluation. In order to determine the electron temperature and the electron density from spectroscopic measurements, an extended corona model as population model of the indium atom has been set up. A simulation of the molecular emission spectra has been implemented to investigate the rovibrational population processes of the indium halide molecules. The impact of the cold spot

Low-cost electrochemical treatment of indium tin oxide anodes for high-efficiency organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Hui Cheng, Chuan, E-mail: chengchuanhui@dlut.edu.cn; Shan Liang, Ze; Gang Wang, Li; Dong Gao, Guo; Zhou, Ting; Ming Bian, Ji; Min Luo, Ying [School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China); Tong Du, Guo, E-mail: dugt@dlut.edu.cn [School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China); State Key Laboratory on Integrated Optoelectronics, College of Electronic Science and Engineering, Jilin University, Changchun 130012 (China)

2014-01-27

We demonstrate a simple low-cost approach as an alternative to conventional O{sub 2} plasma treatment to modify the surface of indium tin oxide (ITO) anodes for use in organic light-emitting diodes. ITO is functionalized with F{sup −} ions by electrochemical treatment in dilute hydrofluoric acid. An electrode with a work function of 5.2 eV is achieved following fluorination. Using this electrode, a maximum external quantum efficiency of 26.0% (91 cd/A, 102 lm/W) is obtained, which is 12% higher than that of a device using the O{sub 2} plasma-treated ITO. Fluorination also increases the transparency in the near-infrared region.

Kinetic study of indium-111 labelled platelets in idiopathic thrombocytopenic purpura

International Nuclear Information System (INIS)

Reiffers, J.; Vuillemin, L.; Broustet, A.; Ducassou, D.

1982-01-01

Labelling platelets with 111 Indium-oxine has advantages over the conventional 51 chromium method: labelling is more efficient and the radiations emitted almost exclusively consist of gamma-rays. Owing to these advantages, autologous platelets can be used for kinetic studies in patients with idiopathic thrombocytopenic purpura, even when thrombocytopenia is severe. 111 Indium labelling also provides accurate information on the sites of platelet destruction, which may help to predict the patient's response to splenectomy [fr

Unusual tensile behaviour of fibre-reinforced indium matrix composite and its in-situ TEM straining observation

International Nuclear Information System (INIS)

Luo, Xin; Peng, Jianchao; Zandén, Carl; Yang, Yanping; Mu, Wei; Edwards, Michael; Ye, Lilei; Liu, Johan

2016-01-01

Indium-based thermal interface materials are superior in thermal management applications of electronic packaging compared to their polymer-based counterparts. However, pure indium has rather low tensile strength resulting in poor reliability. To enhance the mechanical properties of such a material, a new composite consisting of electrospun randomly oriented continuous polyimide fibres and indium was fabricated. The composite has been characterised by tensile tests and in-situ transmission electron microscopy straining observations. It is shown that the composite's ultimate tensile strength at 20 °C is five times higher than that of pure indium, and the strength of the composite exceeds the summation of strengths of the individual components. Furthermore, contrary to most metallic matrix materials, the ultimate tensile strength of the composite decreases with the increased strain rate in a certain range. The chemical composition and tensile fracture of the novel composite have been analysed comprehensively by means of scanning transmission electron microscopy and scanning electron microscopy. A strengthening mechanism based on mutually reinforcing structures formed by the indium and surrounding fibres is also presented, underlining the effect of compressing at the fibre/indium interfaces by dislocation pileups and slip pinning.

Synthesis of indium-111 mesoprotoporphyrin IX

International Nuclear Information System (INIS)

Lee, K.M.; Marshall, A.G.

1981-01-01

Indium-111 mesoprotoporphyrin IX has been prepared by refluxing suitable proportions of InCl 3 , sodium acetate, and mesoprotoporphyrin IX in glacial acetic acid. The labeled metalloporphyrin is sufficiently water-soluble for use as a scanning agent, and can also be incorporated into heme apoproteins for perturbed gamma-gamma angular correlation measurements. (author)

Solvent extraction studies of indium-mixed chelates with β-diketones in benzene media

International Nuclear Information System (INIS)

Sudersanan, M.; Sundaram, A.K.

1975-01-01

Mixed chelate formation of indium with several β-diketones has been studied in benzene media. The extraction of indium by benzoyltrifluoroacetone (BFA) and furoyltrifluoroacetone (FFA) has been carried out as a function of pH and concentration of the ligand to ascertain the nature of the complexes. The extraction of indium by a mixture of β-diketones, viz., BFA-benzoylacetone(BA), BFA-dibenzoylmethene (DBM), FFA-BA, FFA-DBM, FFA-BFA and DBM-BA has also been studied as a function of the solution parameters. The nature of the mixed complexes formed as well as their equilibrium constants, statistical and stabilisation constants have been evaluated. (author)

False positive indium-111 white blood cell scan in a closed clavicle fracture

International Nuclear Information System (INIS)

Friedman, R.J.; Gordon, L.

1988-01-01

Aggressive treatment of the multiply injured patient often requires early fixation of many fractures, some of which may be open. Often, patients develop postoperative fevers requiring a thorough workup to rule out infection. Recently, indium-111 white blood cell (WBC) imaging has become a valuable adjunct in the diagnosis of acute infection. The patient described had a simple, closed clavicle fracture with markedly increased activity on an indium-111 WBC scan obtained for fever workup. This subsequently proved to be a normal, healing, noninfected fracture by other diagnostic techniques. Noninfected, simple closed fractures should be added to the list of causes for a false-positive indium-111 WBC scan

Perturbed-angular-correlation study of the electric-field gradient in 181Hf-doped and implanted indium sesquioxide

International Nuclear Information System (INIS)

Renteria, M.; Requejo, F.G.; Bibiloni, A.G.; Pasquevich, A.F.; Shitu, J.; Freitag, K.

1997-01-01

We studied the hyperfine interactions of 181 Ta in In 2 O 3 by means of perturbed-angular-correlation (PAC) measurements. We prepared thin films of indium sesquioxide with different degrees of initial amorphism and implanted them with 181 Hf. Chemically prepared indium-sesquioxide powder samples were also made starting from neutron-irradiated HfCl 4 , which provides the 181 Hf PAC probes. PAC experiments were performed on each sample at room temperature, after each step of annealing programs at increasing temperatures up to the full crystallization of the samples. The results indicate that the PAC probe occupies preferentially the axially symmetric cation site. Point-charge-model calculations were performed. The calculated asymmetry parameters η were compared with those obtained in 181 Hf PAC experiments performed also on other binary oxides, showing that the symmetry of the electric-field-gradient (EFG) tensor at 181 Ta cation sites in binary oxides is mainly determined by the nearest-neighbor oxygen-ion distribution around the probe. Comparisons of the experimental results in bixbyites obtained for both PAC probes, 111 Cd and 181 Ta, show that the local EFG in bixbyites, are strongly dependent on the geometry of the sites and the electronic configuration of the probes. copyright 1997 The American Physical Society

Effects of Ion Beam Irradiation on Nanoscale InOx Cooper-Pair Insulators

Directory of Open Access Journals (Sweden)

Srdjan Milosavljević

2013-01-01

Full Text Available This paper examines the effects of irradiating indium oxide films of nanoscale thickness by ion beams, when these films are in the Cooper-pair insulator state. Radiation effects are predicted on the basis of Monte Carlo simulations of ion transport. Results of numerical experiments are interpreted within the theoretical model of a Cooper-pair insulator. The study suggests that radiation-induced changes in InOx films exposed to ion beams could significantly alter their current-voltage characteristics and that a transition to a metallic state is possible, due to radiation-induced perturbation of the fine-tuned granular structure. Furthermore, incident and displaced ions can break up enough Cooper pairs in InOx films to cause dissolution of this specific insulating state.

The mobility of indium and gallium in groundwater systems: constraining the role of sorption in sand column experiments

Science.gov (United States)

Dror, I.; Ringering, K.; Yecheskel, Y.; Berkowitz, B.

2017-12-01

The mobility of indium and gallium in groundwater environments was studied via laboratory experiments using quartz sand as a porous medium. Indium and gallium are metals of very low abundance in the Earth's crust and, correspondingly, the biosphere is only adapted to very small concentrations of these elements. However, in modern semiconductor industries, both elements play a central role and are incorporated in devices of mass production such as smartphones and digital cameras. The resulting considerable increase in production, use and discharge of indium and gallium throughout the last two decades, with a continuous and fast increase in the near future, raises questions regarding the fate of both elements in the environment. However, the transport behavior of these two metals in soils and groundwater systems remains poorly understood to date. Because of the low solubility of both elements in aqueous solutions, trisodium citrate was used as a complexation agent to stabilize the solutions, enabling investigation of the transport of these metals at neutral pH. Column experiments showed different binding capacities for indium and gallium, where gallium is much more mobile compared to indium and both metals are substantially retarded in the column. Different affinities were also confirmed by examining sorption isotherms of indium and gallium in equilibrium batch systems. The effect of natural organic matter on the mobility of indium and gallium was also studied, by addition of humic acid. For both metals, the presence of humic acid affects the sorption dynamics: for indium, sorption is strongly inhibited leading to much higher mobility, whereas gallium showed a slightly higher sorption affinity and very similar mobility compared to the same setup without humic acid addition. However, in all cases, the binding capacity of gallium to quartz is much weaker than that of indium. These results are consistent with the assumption that indium and gallium form different types

Indium and thallium

International Nuclear Information System (INIS)

1976-01-01

The physical and the chemical properties and methods for producing indium and its main compounds have been studied. Presented are the major fields of application of the metal, inclusive of the atomic and space engineering. Described are the natural occurrence and the types of deposits of this disseminated element. Given are the main methods for extracting In from various raw materials, the methods being also evaluated economically. It is inferred, that all the conditions being equal, the extraction technique yields In at a lesser cost, a higher recovery and higher labour productivity. Described are methods for manufacturing the frequently used In compounds, such as the antimonide, arsenide, phosphide

Indium flotation from hydrometallurgical solutions

International Nuclear Information System (INIS)

Sviridov, V.V.; Mal'tsev, G.I.; Petryakova, N.K.; Gomzikov, A.I.

1980-01-01

The principal possibility of flotation of indium small quantities (10 -4 gxion/l) is established from sulphuric-acid solutions of leaching converter dusts of the copper melting production in the form of complex compounds with sodium hexametaphosphate and cation-active nitrogen-containing surfactants. It is shown that the flotation process effectiveness is determined by the molar ratio of hexametaphosphate and collector introduced into the solution, solution oxidity and surfactant nature

Evaluation of musculoskeletal sepsis with indium-111 white blood cell imaging

International Nuclear Information System (INIS)

Ouzounian, T.J.; Thompson, L.; Grogan, T.J.; Webber, M.M.; Amstutz, H.C.

1987-01-01

The detection of musculoskeletal sepsis, especially following joint replacement, continues to be a challenging problem. Often, even with invasive diagnostic evaluation, the diagnosis of infection remains uncertain. This is a report on the first 55 Indium-111 white blood cell (WBC) images performed in 39 patients for the evaluation of musculoskeletal sepsis. There were 40 negative and 15 positive Indium-111 WBC images. These were correlated with operative culture and tissue pathology, aspiration culture, and clinical findings. Thirty-eight images were performed for the evaluation of possible total joint sepsis (8 positive and 30 negative images); 17 for the evaluation of nonarthroplasty-related musculoskeletal sepsis (7 positive and 10 negative images). Overall, there were 13 true-positive, 39 true-negative, two false-positive, and one false-negative images. Indium-111 WBC imaging is a sensitive and specific means of evaluating musculoskeletal sepsis, especially following total joint replacement

Indium-bridged [1]ferrocenophanes.

Science.gov (United States)

Bagh, Bidraha; Sadeh, Saeid; Green, Jennifer C; Müller, Jens

2014-02-17

Indium-bridged [1]ferrocenophanes ([1]FCPs) and [1.1]ferrocenophanes ([1.1]FCPs) were synthesized from dilithioferrocene species and indium dichlorides. The reaction of Li2fc⋅tmeda (fc = (H4C5)2Fe) and (Mamx)InCl2 (Mamx = 6-(Me2NCH2)-2,4-tBu2C6H2) gave a mixture of the [1]FCP (Mamx)Infc (4(1)), the [1.1]FCP [(Mamx)Infc]2 (4(2)), and oligomers [(Mamx)Infc]n (4(n)). In a similar reaction, employing the enantiomerically pure, planar-chiral (Sp,Sp)-1,1'-dibromo-2,2'-diisopropylferrocene (1) as a precursor for the dilithioferrocene derivative Li2fc(iPr2), equipped with two iPr groups in the α position, gave the inda[1]ferrocenophane 5(1) [(Mamx)Infc(iPr2)] selectively. Species 5(1) underwent ring-opening polymerization to give the polymer 5(n). The reaction between Li2fc(iPr2) and Ar'InCl2 (Ar' = 2-(Me2NCH2)C6H4) gave an inseparable mixture of the [1]FCP Ar'Infc(iPr2) (6(1)) and the [1.1]FCP [Ar'Infc(iPr2)]2 (6(2)). Hydrogenolysis reactions (BP86/TZ2P) of the four inda[1]ferrocenophanes revealed that the structurally most distorted species (5(1)) is also the most strained [1]FCP. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Radioactive indium labelling of the figured elements of blood. Method, results, applications

International Nuclear Information System (INIS)

Ducassou, D.; Nouel, J.P.

Following the work of Thakur et al. the authors became interested in red corpuscle, leucocyte and platelet labelling with indium 111 or 113m (8 hydroxyquinolein-indium). For easier labelling of the figured elements of blood the technique described was modified. The chelate is prepared by simple contact at room temperature of indium 111 or 113m chloride and water-soluble 8 hydroxyquinolein sulphate, in the presence of 0.2M TRIS buffer. The figured element chosen suspended in physiological serum is added directly to the solution obtained, the platelets and leucocytes being separated out beforehand by differential centrifugation. While it gives results similar to those of Thabur et al. the method proposed avoids the chloroform extraction of the radioactive chelate and the use of alcohol, liable to impair the platelet regation capacity [fr

Electrical and optical properties of amorphous indium zinc oxide films

International Nuclear Information System (INIS)

Ito, N.; Sato, Y.; Song, P.K.; Kaijio, A.; Inoue, K.; Shigesato, Y.

2006-01-01

Valence electron control and electron transport mechanisms on the amorphous indium zinc oxide (IZO) films were investigated. The amorphous IZO films were deposited by dc magnetron sputtering using an oxide ceramic IZO target (89.3 wt.% In 2 O 3 and 10.7 wt.% ZnO). N-type impurity dopings, such as Sn, Al or F, could not lead to the increase in carrier density in the IZO. Whereas, H 2 introduction into the IZO deposition process was confirmed to be effective to increase carrier density. By 30% H 2 introduction into the deposition process, carrier density increased from 3.08 x 10 2 to 7.65 x 10 2 cm -3 , which must be originated in generations of oxygen vacancies or interstitial Zn 2+ ions. Decrease in the transmittance in the near infrared region and increase in the optical band gap were observed with the H 2 introduction, which corresponded to the increase in carrier density. The lowest resistivity of 3.39 x 10 -4 Ω cm was obtained by 10% H 2 introduction without substrate heating during the deposition

Reduced thermal quenching in indium-rich self-organized InGaN/GaN quantum dots

KAUST Repository

Elafandy, Rami T.; Bhattacharya, Pallab K.; Cha, Dong Kyu; Ng, Tien Khee; Ooi, Boon S.; Zhang, Meng

2012-01-01

Differences in optical and structural properties of indium rich (27), indium gallium nitride (InGaN) self-organized quantum dots (QDs), with red wavelength emission, and the two dimensional underlying wetting layer (WL) are investigated. Temperature

Ion implantation by isotope separator on line (ISOL) of indium isotopes

International Nuclear Information System (INIS)

Hanada, Reimon; Murayama, Mitsuhiro; Saito, Shigeru; Nagata, Shinji; Yamaguchi, Sadaei; Shinozuka, Tsutomu; Fujioka, Manabu.

1994-01-01

111 In has been known as the nuclide which is most suitable to perturbed angular correlation (PAC) process, as the life of its intermediate state is long , the half life is proper in view of the measurement and radiation control, and it is easily available as its chloride is on the market. In the PAC, it is necessary to introduce this probe nuclei into samples. The most simple method is diffusion process, but in the materials, of which the solid-solubility of In is low like Fe and Si, the introduction is very difficult, therefore, it is necessary to do ion implantation. The development of this process was tried, and the results are reported. For the experiment, the ISOL in the cyclotron RI center, Tohoku University, was used as the accelerator for the implantation. The experimental method is explained. As the results, in the case of nonradioactive In implantation, the Ruthereford back scattering (RBS) spectra of the Si in which In was implanted, the spectra when the channeling condition was satisfied, and the results of measuring the angle dependence of channeling for In and In-implanted Si are shown. In the case of the ion implantation of radioactive 111 In, the energy spectra of In-implanted Si, the PAC spectra of In-implanted Si samples, and the PAC spectra for pure iron and Fe-Si alloy are shown. The further improvement of the ion sources is necessary. (K.I.)

Effect of Indium nano-sandwiching on the structural and optical performance of ZnSe films

Directory of Open Access Journals (Sweden)

S.E. Al Garni

Full Text Available In the current study, we attempted to explore the effects of the Indium nanosandwiching on the mechanical and optical properties of the physically evaporated ZnSe thin films by means of X-ray diffractions and ultraviolet spectrophotometry techniques. While the thickness of each layer of ZnSe was fixed at 1.0 μm, the thickness of the nanosandwiched Indium thin films was varied in the range of 25–100 nm. It was observed that the as grown ZnSe films exhibits cubic and hexagonal nature of crystallization as those of the ZnSe powders before the film deposition. The cubic phases weighs ∼70% of the structure. The analysis of this phases revealed that there is a systematic variation process presented by the decreasing of; the lattice constant, compressing strain, stress, stacking faults and dislocation intensity and increasing grain size resulted from increasing the Indium layer thickness in the range of 50–100 nm. In addition, the nanosandwiching of Indium between two layers of ZnSe is observed to enhance the absorbability of the ZnSe. Particularly, at incident photon energy of 2.38 eV the absorbability of the ZnSe films which are sandwiched with 100 nm Indium is increased by 13.8 times. Moreover, increasing the thickness of the Indium layer shrinks the optical energy band gap. These systematic variations in mechanical and optical properties are assigned to the better recrystallization process that is associated with Indium insertion which in turn allows total internal energy redistribution in the ZnSe films through the enlargement of grains. Keywords: ZnSe, Nanosandwiching, Mechanical, Optical gap

Optical investigations on indium oxide nano-particles prepared through precipitation method

International Nuclear Information System (INIS)

Seetha, M.; Bharathi, S.; Dhayal Raj, A.; Mangalaraj, D.; Nataraj, D.

2009-01-01

Visible light emitting indium oxide nanoparticles were synthesized by precipitation method. Sodium hydroxide dissolved in ethanol was used as a precipitating agent to obtain indium hydroxide precipitates. Precipitates, thus formed were calcined at 600 deg. C for 1 h to obtain indium oxide nanoparticles. The structure of the particles as determined from the X-Ray diffraction pattern was found to be body centered cubic. The phase transformation of the prepared nanoparticles was analyzed using thermogravimetry. Surface morphology of the prepared nanoparticles was analyzed using high resolution-scanning electron microscopy and transmission electron microscopy. The results of the analysis show cube-like aggregates of size around 50 nm. It was found that the nanoparticles have a strong emission at 427 nm and a weak emission at 530 nm. These emissions were due to the presence of singly ionized oxygen vacancies and the nature of the defect was confirmed through Electron paramagnetic resonance analysis.

Electrical properties of indium arsenide irradiated with fast neutrons

International Nuclear Information System (INIS)

Kolin, N.G.; Osvenskii, V.B.; Rytova, N.S.; Yurova, E.S.

1987-01-01

A study was made of the influence of irradiation with fast reactor neutrons on electrical properties of indium arsenide samples with different dopant concentrations. The laws governing the formation and annealing of radiation defects in indium arsenide were found to be governed by the donor-acceptor interaction. Depending on the density of free carriers in the original crystal, irradiation could produce charged defects of predominantly donor or acceptor types. Donor defects in irradiated InAs samples were annealed practically completely, whereas a considerable fraction of residual acceptor defects was retained even after heat treatment at 900 degree C. The concentration of these residual acceptors depended on the electron density at the annealing temperature

Equation of state of liquid Indium under high pressure

Directory of Open Access Journals (Sweden)

Huaming Li

2015-09-01

Full Text Available We apply an equation of state of a power law form to liquid Indium to study its thermodynamic properties under high temperature and high pressure. Molar volume of molten indium is calculated along the isothermal line at 710K within good precision as compared with the experimental data in an externally heated diamond anvil cell. Bulk modulus, thermal expansion and internal pressure are obtained for isothermal compression. Other thermodynamic properties are also calculated along the fitted high pressure melting line. While our results suggest that the power law form may be a better choice for the equation of state of liquids, these detailed predictions are yet to be confirmed by further experiment.

Indium Tin Oxide-Free Polymer Solar Cells: Toward Commercial Reality

DEFF Research Database (Denmark)

Angmo, Dechan; Espinosa Martinez, Nieves; Krebs, Frederik C

2014-01-01

Polymer solar cell (PSC) is the latest of all photovoltaic technologies which currently lies at the brink of commercialization. The impetus for its rapid progress in the last decade has come from low-cost high throughput production possibility which in turn relies on the use of low-cost materials...... and vacuum-free manufacture. Indium tin oxide (ITO), the commonly used transparent conductor, imposes the majority of the cost of production of PSCs, limits flexibility, and is feared to create bottleneck in the dawning industry due to indium scarcity and the resulting large price fluctuations. As such...

Effect of barrier layers on the properties of indium tin oxide thin films on soda lime glass substrates

International Nuclear Information System (INIS)

Lee, Jung-Min; Choi, Byung-Hyun; Ji, Mi-Jung; An, Yong-Tae; Park, Jung-Ho; Kwon, Jae-Hong; Ju, Byeong-Kwon

2009-01-01

In this paper, the electrical, structural and optical properties of indium tin oxide (ITO) films deposited on soda lime glass (SLG) haven been investigated, along with high strain point glass (HSPG) substrate, through radio frequency magnetron sputtering using a ceramic target (In 2 O 3 :SnO 2 , 90:10 wt.%). The ITO films deposited on the SLG show a high electrical resistivity and structural defects compared with those deposited on HSPG due to the Na ions from the SLG diffusing to the ITO film by annealing. However, these properties can be improved by intercalating a barrier layer of SiO 2 or Al 2 O 3 between the ITO film and the SLG substrate. SIMS analysis has confirmed that the barrier layer inhibits the Na ion's diffusion from the SLG. In particular, the ITO films deposited on the Al 2 O 3 barrier layer, show better properties than those deposited on the SiO 2 barrier layer.

Chemical composition of cadmium selenochromite crystals doped with indium, silver and gallium

International Nuclear Information System (INIS)

Bel'skij, N.K.; Ochertyanova, L.I.; Shabunina, G.G.; Aminov, T.G.

1985-01-01

The high accuracy chemical analysis Which allows one to observe doping effect on the cadmium selenochromite crystal composition is performed. The problem on the possibility of impurity atom substitution for basic element is considered on the basis of data of atomic-absorption analysis of doped crystals. The crystals of cadmium selenochromite doped with indium by chromium to cadmium ratio are distributed into two groups and probably two types of substitution take place. At 0.08-1.5 at.% indium concentrations the Cr/Cd ratio >2. One can assume that indium preferably takes cadmium tetrahedral positions whereas at 1.5-2.5 at. % concentrations the Cr/Cd ratio =2 and cadmium is substituted for silver which does not contradict crystallochemical and physical properties of this compound. In crystals with gallium the Cr/Cd ratio <2. Gallium preferably substitutes chromium

The density of molten indium at temperatures up to 600 K

International Nuclear Information System (INIS)

Alchagirov, B.B.; Khatsukov, A.M.; Mozgovoj, A.G.

2004-01-01

The liquid indium density measurement is carried out through the pycnometric method within the temperature range of 434-600 K both by heating and cooling. The totality of the obtained results was processed through the approximating equation. The root-mean-square deviation of the experimental data from the approximating equation does not exceed ±0.01%. The high accuracy of the obtained results is noted. The deviation of the existing data on the liquid indium density from the approximating equation is shown graphically [ru

Optical and micro-structural characterizations of MBE grown indium gallium nitride polar quantum dots

KAUST Repository

Elafandy, Rami T.

2011-12-01

Comparison between indium rich (27%) InGaN/GaN quantum dots (QDs) and their underlying wetting layer (WL) is performed by means of optical and structural characterizations. With increasing temperature, micro-photoluminescence (μPL) study reveals the superior ability of QDs to prevent carrier thermalization to nearby traps compared to the two dimensional WL. Thus, explaining the higher internal quantum efficiency of the QD nanostructure compared to the higher dimensional WL. Structural characterization (X-ray diffraction (XRD)) and transmission electron microscopy (TEM)) reveal an increase in the QD indium content over the WL indium content which is due to strain induced drifts. © 2011 IEEE.

Positive indium-III bone marrow scan in metastatic breast carcinoma. Case report

International Nuclear Information System (INIS)

LaManna, M.M.; Hyzinski, M.; Swami, V.K.; Parker, J.A.

1984-01-01

Indium is generally presumed to localize in the bone marrow within the erythroid cell line. Fibrosis, inflammation, lymphoma, extended field radiation, chemotherapy, or combinations of both treatment modalities generally depress the uptake of indium by the marrow in a complex fashion. We report a case of metastatic breast carcinoma and pancytopenia in which the In-111 scan appeared qualitatively similar to a Tc-99m MDP bone scan. Findings were confirmed by bone marrow biopsy

Heat-up synthesis of Ag–In–S and Ag–In–S/ZnS nanocrystals: Effect of indium precursors on their optical properties

International Nuclear Information System (INIS)

Chen, Siqi; Ahmadiantehrani, Mojtaba; Zhao, Jialong; Zhu, Shaihong; Mamalis, Athanasios G.; Zhu, Xiaoshan

2016-01-01

Cadmium-free I–III–VI nanocrystals (NCs) have recently attracted much research interests due to their excellent optical properties and low toxicity. In this work, with a simple heat-up synthetic system to prepare high quality Ag–In–S (AIS) NCs and their core/shell structures (AIS/ZnS NCs), we investigated the effect of different indium precursors (indium acetate and indium chloride) on NC optical properties. The measurements on photoluminescence spectra of AIS NCs show that the photoluminescence peak-wavelength of AIS NCs using indium acetate is in the range from 596 to 604 nm, and that of AIS NCs using indium chloride is from 641 to 660 nm. AIS and AIS/ZnS NCs using indium acetate present around 15% and 40% QYs, and both AIS and AIS/ZnS NCs using indium chloride present around 31% QYs. The photoluminescence decay study indicates that the lifetime parameters of AIS and AIS/ZnS using indium chloride are 2–4 times larger than those of AIS and AIS/ZnS NCs using indium acetate. Moreover, AIS NCs using indium chloride have a slower photobleaching dynamics than AIS NCs using indium acetate, and ZnS shell coating on both types of AIS NCs significantly enhances their photostability against UV exposure. We believe that the unique optical properties of AIS and AIS/ZnS NCs will open an avenue for these materials to be employed in broad electronic or biomedical applications. - Highlights: • High quality of AIS and AIS/ZnS NCs were prepared by heat-up. • Different indium precursors in AIS synthesis can impact AIS optical properties. • The impacted optical properties include emission colors, brightness and life time. • The reason why different indium precursors impact optical properties was explored. • The prepared NCs may have broad electronic and biomedical applications.

Electrochemical impedance spectroscopy investigation on indium tin oxide films under cathodic polarization in NaOH solution

International Nuclear Information System (INIS)

Gao, Wenjiao; Cao, Si; Yang, Yanze; Wang, Hao; Li, Jin; Jiang, Yiming

2012-01-01

The electrochemical corrosion behaviors of indium tin oxide (ITO) films under the cathodic polarization in 0.1 M NaOH solution were investigated by electrochemical impedance spectroscopy. The as-received and the cathodically polarized ITO films were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction for morphological, compositional and structural studies. The results showed that ITO films underwent a corrosion process during the cathodic polarization and the main component of the corrosion products was body-centered cubic indium. The electrochemical impedance parameters were related to the effect of the cathodic polarization on the ITO specimens. The capacitance of ITO specimens increased, while the charge transfer resistance and the inductance decreased with the increase of the polarization time. The proposed mechanism indicated that the corrosion products (metallic indium) were firstly formed during the cathodic polarization and then absorbed on the surface of the ITO film. As the surface was gradually covered by indium particles, the corrosion process was suppressed. - Highlights: ► Cathodic polarization of indium tin oxide (ITO) in 0.1 M NaOH. ► Cathodic polarization studied with electrochemical impedance spectroscopy. ► ITO underwent a corrosion attack during cathodic polarization, indium was observed. ► Electrochemical parameters of ITO were obtained using equivalent electrical circuit. ► A corrosion mechanism is proposed.

Planar self-aligned ion implanted InP MISFETS for fast logic applications

International Nuclear Information System (INIS)

Cameron, D.C.; Irving, L.D.; Whitehouse, C.R.; Woodward, J.; Lee, D.

1983-01-01

The first successful use of ion implantation to fabricate truly self-aligned planar n-channel enhancement-mode indium phosphide MISFITS is reported. The transistors have been fabricated on iron-doped semi-insulating material using PECVD-deposited SiO 2 as the gate dielectric and molybdenum gate electrodes. The self-aligned source and drain contact regions were produced by Si 29 ion implantation using each gate stripe as an implant mask. The devices fabricated to date have exhibited channel mobilities up to value of 2400 cm 2 v -1 s -1 , with excellent uniformity and stability of the device characteristics also being observed. (author)

Indium-111 granulocyte scintigraphy in inflammatory bowel disease

International Nuclear Information System (INIS)

Devillers, A.; Moisan, A.; Heresbach, D.; Darnault, P.; Bretagne, J.F.

1996-01-01

The present paper reports our experience since 1963 concerning 111-indium labeled autologous granulocytes scanning in the assessment of inflammatory bowel diseases and in the assessment of activity in Crohn's disease and ulcerative colitis. (authors). 94 refs., 3 figs

Effect of heat treatment on anodic activation of aluminium by trace element indium

Energy Technology Data Exchange (ETDEWEB)

Graver, Brit [Department of Materials Science and Engineering, Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Helvoort, Antonius T.J. van [Department of Physics, Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Nisancioglu, Kemal, E-mail: kemal.nisancioglu@material.ntnu.n [Department of Materials Science and Engineering, Norwegian University of Science and Technology, N-7491 Trondheim (Norway)

2010-11-15

Research highlights: {yields} Indium segregation activates AlIn alloy surface anodically in chloride solution. {yields} Enrichment of In on Al surface can occur thermally by heat treatment at 300 {sup o}C. {yields} Increasing temperature homogenises indium in aluminium reducing anodic activation. {yields} Indium can activate AlIn surface by segregating through dealloying of aluminium. {yields} Anodic activation is caused by AlIn amalgam formation at aluminium surface. - Abstract: The presence of trace elements in Group IIIA-VA is known to activate aluminium anodically in chloride environment. The purpose of this paper is to investigate the surface segregation of trace element In by heat treatment and resulting surface activation. Model binary AlIn alloys, containing 20 and 1000 ppm by weight of In, were characterized after heat treatment at various temperatures by use of glow discharge optical emission spectroscopy, electron microscopy and electrochemical polarization. Heat treatment for 1 h at 300 {sup o}C gave significant segregation of discrete In particles (thermal segregation), which activated the surface. Indium in solid solution with aluminium, obtained by 1 h heat treatment at 600 {sup o}C, also activated by surface segregation of In on alloy containing 1000 ppm In, resulting from the selective dissolution of the aluminium component during anodic oxidation (anodic segregation). The effect of anodic segregation was reduced by decreasing indium concentration in solid solution; it had negligible effect at the 20 ppm level. The segregated particles were thought to form a liquid phase alloy with aluminium during anodic polarization, which in turn, together with the chloride in the solution destabilized the oxide.

Hydrogen ion sensors based on indium tin oxide thin film using radio frequency sputtering system

International Nuclear Information System (INIS)

Chiang, Jung-Lung; Jhan, Syun-Sheng; Hsieh, Shu-Chen; Huang, An-Li

2009-01-01

Indium tin oxide (ITO) thin films were deposited onto Si and SiO 2 /Si substrates using a radio frequency sputtering system with a grain size of 30-50 nm and thickness of 270-280 nm. ITO/Si and ITO/SiO 2 /Si sensing structures were achieved and connected to a standard metal-oxide-semiconductor field-effect transistor (MOSFET) as an ITO pH extended-gate field-effect transistor (ITO pH-EGFET). The semiconductor parameter analysis measurement (Keithley 4200) was utilized to measure the current-voltage (I-V) characteristics curves and study the sensing properties of the ITO pH-EGFET. The linear pH voltage sensitivities were about 41.43 and 43.04 mV/pH for the ITO/Si and ITO/SiO 2 /Si sensing structures, respectively. At the same time, both pH current sensitivities were about 49.86 and 51.73 μA/pH, respectively. Consequently, both sensing structures can be applied as extended-gate sensing heads. The separative structure is suitable for application as a disposable pH sensor.

Enhanced photoelectrochemical properties of 100 MeV Si8+ ion irradiated barium titanate thin films

International Nuclear Information System (INIS)

Solanki, Anjana; Choudhary, Surbhi; Satsangi, Vibha R.; Shrivastav, Rohit; Dass, Sahab

2013-01-01

Highlights: ► Effect of 100 MeV Si 8+ ion irradiation on photoelectrochemical (PEC) properties of BaTiO 3 thin films was studied. ► Films were deposited on Indium doped Tin Oxide (ITO) coated glass by sol–gel spin coating technique. ► Optimal irradiation fluence for best PEC response was 5 × 10 11 ion cm −2 . ► Maximum photocurrent density was observed to be 0.7 mA cm −2 at 0.4 V/SCE. ► Enhanced photo-conversion efficiency was due to maximum negative flatband potential, donor density and lowest resistivity. -- Abstract: Effects of high electronic energy deposition on the structure, surface topography, optical property and photoelectrochemical behavior of barium titanate (BaTiO 3 ) thin films were investigated by irradiating films with 100 MeV Si 8+ ions at different ion fluences in the range of 1 × 10 11 –2 × 10 13 ions cm −2 . BaTiO 3 thin films were deposited on indium tin oxide coated glass substrate by sol gel spin coating method. Irradiation induced modifications in the films were analyzed using the results from XRD, SEM, cross sectional SEM, AFM and UV–Vis spectrometry. Maximum photocurrent density of 0.7 mA cm −2 at 0.4 V/SCE and applied bias hydrogen conversion efficiency (ABPE) of 0.73% was observed for BaTiO 3 film irradiated at 5 × 10 11 ions cm −2 , which can be attributed to maximum negative value of the flatband potential and donor density and lowest resistivity

X-ray photoelectron spectroscopy/Ar+ ion profile study of thin oxide layers on InP

International Nuclear Information System (INIS)

Thurgate, S.M.; Erickson, N.E.

1990-01-01

The effect of incremental ion bombardment on the surface layers of an aqua regia etched InP sample was studied by monitoring the components of the In 3d 5/2 and O 1s x-ray photoelectron spectroscopy (XPS) lines as the sample was bombarded with low energy (1 keV) Ar + ions. The changes in the stoichiometry of the surface produced large shifts in the position of the In 3d and O 1s lines that were not paralleled by shifts in the P 2p line. Analysis of these shifts indicated that the surface was covered with a mixture of indium hydroxide and indium phosphate, with the phosphate closer to the InP substrate. It is proposed that this layer structure is due to differences in the dissolution rates of the oxidation products in the acid etch and the effect of the distilled water rinse. It may be possible to alter the composition of such oxides by carefully tailoring the etch conditions to optimize the kinetics for the particular oxide phase required. The analysis of the XPS lines also showed that the InP substrate was damaged at very low ion doses, and finally decomposed by the ion beam. When the ion ''cleaned'' sample was exposed to oxygen, a different oxide system was produced which consisted largely of In 2 O 3 and InPO 4 [or In(PO 3 ) x ]. This model of the oxidized surface of InP is consistent with other measurements and we conclude that ion milling together with XPS and careful curve fitting can be used to find the nature of the thin oxides on InP

Recovery of indium from used LCD panel by a time efficient and environmentally sound method assisted HEBM

Energy Technology Data Exchange (ETDEWEB)

Lee, Cheol-Hee; Jeong, Mi-Kyung [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, Cheonan 331-717 (Korea, Republic of); Fatih Kilicaslan, M. [Department of Physics, Faculty of Art and Science, Kastamonu University, Kastamonu (Turkey); Lee, Jong-Hyeon [Graduate School of Green Energy Technology and Department of Nanomaterials Engineering, Chungnam National University, 79 Daehak-ro, Yuseong-gu, Dajeon 305-764 (Korea, Republic of); Hong, Hyun-Seon [Advanced Materials and Processing Center, Institute for Advanced Engineering (IAE), Yongin 449-863 (Korea, Republic of); Hong, Soon-Jik, E-mail: hongsj@kongju.ac.kr [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, Cheonan 331-717 (Korea, Republic of)

2013-03-15

Highlights: ► In this study, we recovered indium from a waste LCD panel. ► The ITO glass was milled to obtain micron size particles in a HEBM machine. ► Effect of particle size of ITO glass on the amount of dissolved In was investigated. ► In a very short time, a considerable amount of In was recovered. ► Amount of HCl in acid solution was decreased to 40 vol.%. - Abstract: In this study, a method which is environmentally sound, time and energy efficient has been used for recovery of indium from used liquid crystal display (LCD) panels. In this method, indium tin oxide (ITO) glass was crushed to micron size particles in seconds via high energy ball milling (HEBM). The parameters affecting the amount of dissolved indium such as milling time, particle size, effect time of acid solution, amount of HCl in the acid solution were tried to be optimized. The results show that by crushing ITO glass to micron size particles by HEBM, it is possible to extract higher amount of indium at room temperature than that by conventional methods using only conventional shredding machines. In this study, 86% of indium which exists in raw materials was recovered about in a very short time.

Electrical features of an amorphous indium-gallium-zinc-oxide film transistor using a double active matrix with different oxygen contents

International Nuclear Information System (INIS)

Koo, Ja Hyun; Kang, Tae Sung; Hong, Jin Pyo

2012-01-01

The electrical characteristics of amorphous indium-gallium-zinc-oxide (a-IGZO) thin film transistor (TFTs) are systematically studied using a double a-IGZO active layer that is composed of a-IGZO x (oxygen-ion-poor region) and a-IGZO y (oxygen-ion-rich-region). An active layer is designed to have a serially-stacked bi-layer matrix with different oxygen contents, providing the formation of different electron conduction channels. Two different oxygen contents in the active layer are obtained by varying the O 2 partial pressure during sputtering. The a-IGZO TFT based on a double active layer exhibits a high mobility of 9.1 cm 2 /Vsec, a threshold voltage (V T ) of 16.5 V, and ΔV T shifts of less than 1.5 V under gate voltage stress. A possible electrical sketch for the double active layer channel is also discussed.

Electron emission from individual indium arsenide semiconductor nanowires

NARCIS (Netherlands)

Heeres, E.C.; Bakkers, E.P.A.M.; Roest, A.L.; Kaiser, M.A.; Oosterkamp, T.H.; Jonge, de N.

2007-01-01

A procedure was developed to mount individual semiconductor indium arsenide nanowires onto tungsten support tips to serve as electron field-emission sources. The electron emission properties of the single nanowires were precisely determined by measuring the emission pattern, current-voltage curve,

A sol-gel method to synthesize indium tin oxide nanoparticles

Institute of Scientific and Technical Information of China (English)

Xiuhua Li; Xiujuan xu; Xin Yin; Chunzhong Li; Jianrong Zhang

2011-01-01

Transparent conductive indium tin oxide (ITO) nanoparticles were synthesized by a novel sol-gel method.Granulated indium and tin were dissolved in HNO3 and partially complexed with citric acid.A sol-gel process was induced when tertiary butyl alcohol was added dropwise to the above solution.ITO nanoparticles with an average crystallite size of 18.5 nm and surface area of 32.6 m2/g were obtained after the gel was heat-treated at 700 C.The ITO nanoparticles showed good sinterability,the starting sintering temperature decreased sharply to 900 C,and the 1400 C sintered pellet had a density of 98.1 ％ of theoretical density (TD).

Polarografic study about the complex formation between indium (III) and sodium azide, in aqueous media

International Nuclear Information System (INIS)

Tokoro, R.; Bertotti, M.

1988-01-01

The present work is a branch of the main work concerned with the complex formation between several metal cations and azide ligand in aqueous media. The polarographic behavior of indium in azide system showed the tendency of complexation. Using polarographic method to determine the half potential of indium at each analytical concentration afforded experimental data to evaluate the constants. The azide concentrations was modified from 1 m to 100 m , the ionic strength held at 2,0 M with sodium perchlorate, indium concentration 7.892 x 10 -4 M, and temperature kept constant at 25,0 0 C. (author) [pt

Some studies on successive ionic layer adsorption and reaction (SILAR) grown indium sulphide thin films

International Nuclear Information System (INIS)

Pathan, H.M.; Lokhande, C.D.; Kulkarni, S.S.; Amalnerkar, D.P.; Seth, T.; Han, Sung-Hwan

2005-01-01

Indium sulphide (In 2 S 3 ) thin films were grown on amorphous glass substrate by the successive ionic layer adsorption and reaction (SILAR) method. X-ray diffraction, optical absorption, scanning electron microscopy (SEM) and Rutherford back scattering (RBS) were applied to study the structural, optical, surface morphological and compositional properties of the indium sulphide thin films. Utilization of triethanolamine and hydrazine hydrate complexed indium sulphate and sodium sulphide as precursors resulted in nanocrystalline In 2 S 3 thin film. The optical band gap was found to be 2.7 eV. The film appeared to be smooth and homogeneous from SEM study

Indium phosphide space solar cell research: Where we are and where we are going

Science.gov (United States)

Jain, R. K.; Flood, D. J.; Weinberg, Irving

1995-01-01

Indium phosphide is considered to be a strong contender for many photovoltaic space applications because of its radiation resistance and its potential for high efficiency. An overview of recent progress is presented, and possible future research directions for indium phosphide space solar cells are discussed. The topics considered include radiation damage studies and space flight experiments.

Standard test methods for chemical and spectrochemical analysis of nuclear-Grade silver-indium-cadmium alloys

CERN Document Server

American Society for Testing and Materials. Philadelphia

1990-01-01

1.1 These test methods cover procedures for the chemical and spectrochemical analysis of nuclear grade silver-indium-cadmium (Ag-In-Cd) alloys to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Silver, Indium, and Cadmium by a Titration Method 7-15 Trace Impurities by Carrier-Distillation Spectro- chemical Method 16-22 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard and precautionary statements, see Section 5 and Practices E50. 7.1 This test method is applicable to the determination of silver, indium, and cadmium in alloys of approximately 80 % silver, 15 % indium, and 5 % cadmium used in nuclear reactor control r...

Pyrolytically grown indium sulfide sensitized zinc oxide nanowires for solar water splitting

Energy Technology Data Exchange (ETDEWEB)

Komurcu, Pelin; Can, Emre Kaan; Aydin, Erkan; Semiz, Levent [Micro and Nanotechnology Graduate Program, TOBB University of Economics and Technology, 06560 Ankara (Turkey); Gurol, Alp Eren; Alkan, Fatma Merve [Department of Materials Science and Nanotechnology Engineering, TOBB University of Economics and Technology, 06560 Ankara (Turkey); Sankir, Mehmet; Sankir, Nurdan Demirci [Micro and Nanotechnology Graduate Program, TOBB University of Economics and Technology, 06560 Ankara (Turkey); Department of Materials Science and Nanotechnology Engineering, TOBB University of Economics and Technology, 06560 Ankara (Turkey)

2015-11-15

Zinc oxide (ZnO) nanowires, sensitized with spray pyrolyzed indium sulfide, were obtained by chemical bath deposition. The XRD analysis indicated dominant evolution of hexagonal ZnO phase. Significant gain in photoelectrochemical current using ZnO nanowires is largely accountable to enhancement of the visible light absorption and the formation of heterostructure. The maximum photoconversion efficiency of 2.77% was calculated for the indium sulfide sensitized ZnO nanowire photoelectrodes. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Indium-111 platelet scintigraphy in carotid disease

International Nuclear Information System (INIS)

Branchereau, A.; Bernard, P.J.; Ciosi, G.; Bazan, M.; de Laforte, C.; Elias, A.; Bouvier, J.L.

1988-01-01

Forty-five patients (35 men, 10 women) undergoing carotid surgery had Indium-111 platelet scintigraphy as part of their preoperative work-up. Imaging was performed within three hours after injection of the Indium-111. A second series of views was obtained 24 hours later and repeated at 24 hour intervals for two days. Of 54 scintigrams, 22 were positive and 32 negative. Positive results were defined as a twofold or more increase in local activity on a visualized carotid after 24 hours. The sensitivity of the method was 41%, intraoperatively, and the specificity, 100%. The low sensitivity places this method behind sonography and duplex-scanning for screening patients for surgery. We believe that indications for platelet scintigraphy are limited to: 1. Repeated transient ischemic attacks in the same territory with minimal lesions on arteriography and non-homogeneous plaque on duplex scan; 2. Symptomatic patients being treated medically as a possible argument for surgery; 3. Determining therapeutic policy for patients having experienced a transient ischemic attack with a coexisting intracardiac thrombus

Transparent conductive electrodes of mixed TiO2−x–indium tin oxide for organic photovoltaics

KAUST Repository

Lee, Kyu-Sung; Lim, Jong-Wook; Kim, Han-Ki; Alford, T. L.; Jabbour, Ghassan E.

2012-01-01

A transparent conductive electrode of mixed titanium dioxide (TiO2−x)–indium tin oxide (ITO) with an overall reduction in the use of indium metal is demonstrated. When used in organic photovoltaicdevices based on bulk heterojunction photoactive

Synthesis of indium nanoparticles at ambient temperature; simultaneous phase transfer and ripening

Energy Technology Data Exchange (ETDEWEB)

Aghazadeh Meshgi, Mohammad; Kriechbaum, Manfred [Graz University of Technology, Institute of Inorganic Chemistry (Austria); Biswas, Subhajit; Holmes, Justin D., E-mail: j.holmes@ucc.ie [University College Cork, Materials Chemistry and Analysis Group, Department of Chemistry and the Tyndall National Institute (Ireland); Marschner, Christoph, E-mail: christoph.marschner@tugraz.at [Graz University of Technology, Institute of Inorganic Chemistry (Austria)

2016-12-15

The synthesis of size-monodispersed indium nanoparticles via an innovative simultaneous phase transfer and ripening method is reported. The formation of nanoparticles occurs in a one-step process instead of well-known two-step phase transfer approaches. The synthesis involves the reduction of InCl{sub 3} with LiBH{sub 4} at ambient temperature and although the reduction occurs at room temperature, fine indium nanoparticles, with a mean diameter of 6.4 ± 0.4 nm, were obtained directly in non-polar n-dodecane. The direct synthesis of indium nanoparticles in n-dodecane facilitates their fast formation and enhances their size-monodispersity. In addition, the nanoparticles were highly stable for more than 2 months. The nanoparticles were characterised by dynamic light scattering (DLS), small angle X-ray scattering (SAXS), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS) and Fourier transform infrared (FT-IR) spectroscopy to determine their morphology, structure and phase purity.

Indium recovery from acidic aqueous solutions by solvent extraction with D2EHPA: a statistical approach to the experimental design

Directory of Open Access Journals (Sweden)

Fortes M.C.B.

2003-01-01

Full Text Available This experimental work presents the optimization results of obtaining a high indium concentration solution and minimum iron poisoning by solvent extraction with D2EHPA solubilized in isoparaffin and exxsol. The variables studied in the extraction step were D2EHPA concentration, acidity of the aqueous phase and time of contact between phases. Different hydrochloric and sulfuric acid concentrations were studied for the stripping step. The optimum experimental conditions resulted in a solution with 99% indium extraction and less than 4% iron. The construction of a McCabe-Thiele diagram indicated two theoretical countercurrent stages for indium extraction and at least six stages for indium stripping. Finally, the influence of associated metals found in typical sulfate leach liquors from zinc plants was studied. Under the experimental conditions for maximum indium extraction, 96% indium extraction was obtained, iron extraction was about 4% and no Ga, Cu and Zn were co-extracted.

New compounds of indium(III) with 2,4'-bipyridine

International Nuclear Information System (INIS)

Czakis-Sulikowska, D.; Kaluzna-Czaplinska, J.

2000-01-01

The aim of present work was to obtain complexes of indium(III) with 2,4'-bipyridine and examine some of their physico-chemical properties (solubility, molar conductivity in methanol, IR spectra and thermal analysis)

Influences of Indium Tin Oxide Layer on the Properties of RF Magnetron-Sputtered (BaSr)TiO3 Thin Films on Indium Tin Oxide-Coated Glass Substrate

Science.gov (United States)

Kim, Tae Song; Oh, Myung Hwan; Kim, Chong Hee

1993-06-01

Nearly stoichiometric ((Ba+Sr)/Ti=1.08-1.09) and optically transparent (BaSr)TiO3 thin films were deposited on an indium tin oxide (ITO)-coated glass substrate by means of rf magnetron sputtering for their application to the insulating layer of an electroluminescent flat panel display. The influence of the ITO layer on the properties of (BaSr)TiO3 thin films deposited on the ITO-coated substrate was investigated. The ITO layer did not affect the crystallographic orientation of (BaSr)TiO3 thin film, but enhanced the grain growth. Another effect of the ITO layer on (BaSr)TiO3 thin films was the interdiffusion phenomenon, which was studied by means of secondary ion mass spectrometry (SIMS). As the substrate temperature increased, interdiffusion intensified at the interface not only between the grown film and ITO layer but also between the ITO layer and base glass substrate. The refractive index (nf) of (BaSr)TiO3 thin film deposited on a bare glass substrate was 2.138-2.286, as a function of substrate temperature.

Electrical and optical properties of reactive dc magnetron sputtered silver-doped indium oxide thin films: role of oxygen

International Nuclear Information System (INIS)

Subrahmanyam, A.; Barik, U.K.

2006-01-01

Silver-doped indium oxide thin films have been prepared on glass and quartz substrates at room temperature (300 K) by a reactive dc magnetron sputtering technique using an alloy target of pure indium and silver (80:20 at. %). During sputtering, the oxygen flow rates are varied in the range 0.00-2.86 sccm keeping the magnetron power constant at 40 W. The resistivity of these films is in the range 10 0 -10 -3 Ωcm and they show a negative temperature coefficient of resistivity. The films exhibit p-type conductivity at an oxygen flow rate of 1.71 sccm. The work function of these silver-indium oxide films has been measured by a Kelvin probe technique. The refractive index of the films (at 632.8 nm) varies in the range 1.13-1.20. Silver doping in indium oxide narrows the band gap of indium oxide (3.75 eV). (orig.)

Electrical and optical properties of reactive dc magnetron sputtered silver-doped indium oxide thin films: role of oxygen

Energy Technology Data Exchange (ETDEWEB)

Subrahmanyam, A; Barik, U K [Indian Institute of Technology Madras, Semiconductor Physics Laboratory, Department of Physics, Chennai (India)

2006-07-15

Silver-doped indium oxide thin films have been prepared on glass and quartz substrates at room temperature (300 K) by a reactive dc magnetron sputtering technique using an alloy target of pure indium and silver (80:20 at. %). During sputtering, the oxygen flow rates are varied in the range 0.00-2.86 sccm keeping the magnetron power constant at 40 W. The resistivity of these films is in the range 10{sup 0}-10{sup -3} {omega}cm and they show a negative temperature coefficient of resistivity. The films exhibit p-type conductivity at an oxygen flow rate of 1.71 sccm. The work function of these silver-indium oxide films has been measured by a Kelvin probe technique. The refractive index of the films (at 632.8 nm) varies in the range 1.13-1.20. Silver doping in indium oxide narrows the band gap of indium oxide (3.75 eV). (orig.)

TEM and XANES study of MOVPE grown InAIN layers with different indium content

International Nuclear Information System (INIS)

Kret, S; Wolska, A; Klepka, M T; Letrouit, A; Ivaldi, F; Szczepańska, A; Carlin, J-F; Kaufmann, N A K; Grandjean, N

2011-01-01

We present structure and spatially resolved composition studies by TEM (Transmission Electron Microscopy) and XANES (X-ray Absorption Near Edge Structure) of InAIN MOVPE (Metal-Organic Vapor Phase Epitaxy) epilayers containing 16-27 at% of indium. Investigations of the In L 3 edge by synchrotron radiation absorption show a significant change of the post-edge structure depending on the indium content. We attribute this to the solubility limit and phase separation in this system. Our measurements suggest that the critical composition is 18% for our growth conditions. HRTEM cross-sectional and EDX investigations confirm such phase separation as well as the changing of the structure from 2D growth to columnar like growth for the sample with the highest indium content.

Indium sulfide buffer layers deposited by dry and wet methods

International Nuclear Information System (INIS)

Asenjo, B.; Sanz, C.; Guillen, C.; Chaparro, A.M.; Gutierrez, M.T.; Herrero, J.

2007-01-01

Indium sulfide (In 2 S 3 ) thin films have been deposited on amorphous glass, glass coated by tin oxide (TCO) and crystalline silicon substrates by two different methods: modulated flux deposition (MFD) and chemical bath deposition (CBD). Composition, morphology and optical characterization have been carried out with Scanning Electron Microscopy (SEM), IR-visible-UV Spectrophotometry, X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectrometer. Different properties of the films have been obtained depending on the preparation techniques. With MFD, In 2 S 3 films present more compact and homogeneous surface than with CBD. Films deposited by CBD present also indium oxide in their composition and higher absorption edge values when deposited on glass

Isotope release cytotoxicity assay applicable to human tumors: the use of 111-indium

Energy Technology Data Exchange (ETDEWEB)

Frost, P; Wiltrout, R; Maciorowski, Z; Rose, N R

1977-01-01

We have demonstrated that human tumors can be labelled efficiently with the 111indium-oxine chelate. Subsequently, this isotope can be released by cytotoxic lymphoid cells. Both natural and induced cytotoxicity can be demonstrated utilizing this isotope release method. Because of the slow spontaneous release of 111indium and its efficient labelling of human tumor cells, this isotope release assay can be utilized in long-term cytotoxic assays in the study of human tumor immunology.

Improved field emission from indium decorated multi-walled carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Sreekanth, M.; Ghosh, S., E-mail: santanu1@physics.iitd.ernet.in; Biswas, P.; Kumar, S.; Srivastava, P.

2016-10-15

Graphical abstract: Improved field emission properties have been achieved for Indium (In) decorated MWCNTs and are shown using the schematic of field emission set up with In/CNT cathode, and a plot of J-E characteristics for pristine and In decorated CNTs. - Highlights: • Field emission (FE) properties have been studied for the first time from Indium (In) decorated MWCNT films. • Observed increased density of states near the Fermi level for In decorated films. • Superior field emission properties have been achieved for In decorated CNT films. - Abstract: Multi-walled carbon nanotube (MWCNT) films were grown using thermal chemical vapor deposition (T-CVD) process and were decorated with indium metal particles by thermal evaporation technique. The In metal particles are found to get oxidized. The In decorated films show 250% enhancement in the FE current density, lower turn-on and threshold fields, and better temporal stability as compared to their undecorated counterpart. This improvement in field emission properties is primarily attributed to increased density of states near the Fermi level. The presence of O 2p states along with a small contribution from In 5s states results in the enhancement of density of states in the vicinity of the Fermi level.

Effect of indium accumulation on the characteristics of a-plane InN epi-films under different growth conditions

Energy Technology Data Exchange (ETDEWEB)

Lo, Yun-Yo [Institute of Photonics, National Changhua University of Education, Changhua, Taiwan, ROC (China); Huang, Man-Fang, E-mail: mfhuang@cc.ncue.edu.tw [Institute of Photonics, National Changhua University of Education, Changhua, Taiwan, ROC (China); Chiang, Yu-Chia [Institute of Photonics, National Changhua University of Education, Changhua, Taiwan, ROC (China); Fan, Jenn-Chyuan [Department of Electronic Engineering, Nan Kai University of Technology, Nantou, Taiwan, ROC (China)

2015-08-31

This study investigated the influence of indium accumulation happened on the surface of a-plane InN grown under different growth conditions. Three different growth rates with N/In ratio from stoichiometric to N-rich were used to grow a-plane InN epifilms on GaN-buffered r-plane sapphires by plasma-assisted molecular beam epitaxy. When a-plane InN was grown above 500 °C with a high growth rate, abnormally high in-situ reflectivity was found during a-plane InN growth, which was resulted from indium accumulation on surface owing to In-N bonding difficulty on certain crystal faces of a-plane InN surface. Even using excess N-flux, indium accumulation could still be found in initial growth and formed 3-dimension-like patterns on a-plane InN surface which resulted in rough surface morphology. By reducing growth rate, surface roughness was improved because indium atoms could have more time to migrate to suitable position. Nonetheless, basal stacking fault density and crystal anisotropic property were not affected by growth rate. - Highlights: • High growth temperature could cause indium accumulation on a-plane InN surface. • Indium accumulation on a-plane InN surface causes rough surface. • Low growth rate improves surface morphology but not crystal quality.

Perturbed-angular-correlation study of the electric-field gradient in {sup 181}Hf-doped and implanted indium sesquioxide

Energy Technology Data Exchange (ETDEWEB)

Renteria, M.; Requejo, F.G.; Bibiloni, A.G.; Pasquevich, A.F.; Shitu, J. [Departamento de Fisica, Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC N67, 1900 La Plata (Argentina); Freitag, K. [Institut fuer Strahlen- und Kernphysik der Universitaet Bonn, Nussallee 14-16, 5300 Bonn (Germany)

1997-06-01

We studied the hyperfine interactions of {sup 181}Ta in In{sub 2}O{sub 3} by means of perturbed-angular-correlation (PAC) measurements. We prepared thin films of indium sesquioxide with different degrees of initial amorphism and implanted them with {sup 181}Hf. Chemically prepared indium-sesquioxide powder samples were also made starting from neutron-irradiated HfCl{sub 4}, which provides the {sup 181}Hf PAC probes. PAC experiments were performed on each sample at room temperature, after each step of annealing programs at increasing temperatures up to the full crystallization of the samples. The results indicate that the PAC probe occupies preferentially the axially symmetric cation site. Point-charge-model calculations were performed. The calculated asymmetry parameters {eta} were compared with those obtained in {sup 181}Hf PAC experiments performed also on other binary oxides, showing that the symmetry of the electric-field-gradient (EFG) tensor at {sup 181}Ta cation sites in binary oxides is mainly determined by the nearest-neighbor oxygen-ion distribution around the probe. Comparisons of the experimental results in bixbyites obtained for both PAC probes, {sup 111}Cd and {sup 181}Ta, show that the local EFG in bixbyites, are strongly dependent on the geometry of the sites and the electronic configuration of the probes. {copyright} {ital 1997} {ital The American Physical Society}

An Indium-Free Anode for Large-Area Flexible OLEDs: Defect-Free Transparent Conductive Zinc Tin Oxide

NARCIS (Netherlands)

Morales-Masis, M.; Dauzou, F.; Jeangros, Q.; Dabirian, A.; Lifka, H.; Gierth, R.; Ruske, M.; Moet, D.; Hessler-Wyser, A.; Ballif, C.

2016-01-01

Flexible large-area organic light-emitting diodes (OLEDs) require highly conductive and transparent anodes for efficient and uniform light emission. Tin-doped indium oxide (ITO) is the standard anode in industry. However, due to the scarcity of indium, alternative anodes that eliminate its use are

Correlative scanning electron and confocal microscopy imaging of labeled cells coated by indium-tin-oxide

KAUST Repository

Rodighiero, Simona

2015-03-22

Confocal microscopy imaging of cells allows to visualize the presence of specific antigens by using fluorescent tags or fluorescent proteins, with resolution of few hundreds of nanometers, providing their localization in a large field-of-view and the understanding of their cellular function. Conversely, in scanning electron microscopy (SEM), the surface morphology of cells is imaged down to nanometer scale using secondary electrons. Combining both imaging techniques have brought to the correlative light and electron microscopy, contributing to investigate the existing relationships between biological surface structures and functions. Furthermore, in SEM, backscattered electrons (BSE) can image local compositional differences, like those due to nanosized gold particles labeling cellular surface antigens. To perform SEM imaging of cells, they could be grown on conducting substrates, but obtaining images of limited quality. Alternatively, they could be rendered electrically conductive, coating them with a thin metal layer. However, when BSE are collected to detect gold-labeled surface antigens, heavy metals cannot be used as coating material, as they would mask the BSE signal produced by the markers. Cell surface could be then coated with a thin layer of chromium, but this results in a loss of conductivity due to the fast chromium oxidation, if the samples come in contact with air. In order to overcome these major limitations, a thin layer of indium-tin-oxide was deposited by ion-sputtering on gold-decorated HeLa cells and neurons. Indium-tin-oxide was able to provide stable electrical conductivity and preservation of the BSE signal coming from the gold-conjugated markers. © 2015 Wiley Periodicals, Inc.

Phosphasalen indium complexes showing high rates and isoselectivities in rac-lactide polymerizations

Energy Technology Data Exchange (ETDEWEB)

Myers, Dominic; White, Andrew J.P. [Department of Chemistry, Imperial College London (United Kingdom); Forsyth, Craig M. [School of Chemistry, Monash University, Clayton, VIC (Australia); Bown, Mark [CSIRO Manufacturing, Bayview Avenue, Clayton, VIC (Australia); Williams, Charlotte K. [Department of Chemistry, Oxford University (United Kingdom)

2017-05-02

Polylactide (PLA) is the leading bioderived polymer produced commercially by the metal-catalyzed ring-opening polymerization of lactide. Control over tacticity to produce stereoblock PLA, from rac-lactide improves thermal properties but is an outstanding challenge. Here, phosphasalen indium catalysts feature high rates (30±3 m{sup -1} min{sup -1}, THF, 298 K), high control, low loadings (0.2 mol %), and isoselectivity (P{sub i}=0.92, THF, 258 K). Furthermore, the phosphasalen indium catalysts do not require any chiral additives. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effect of fabrication conditions on the properties of indium tin oxide powders

International Nuclear Information System (INIS)

Xie Wei

2008-01-01

This paper reports that indium tin oxide (ITO) crystalline powders are prepared by coprecipitation method. Fabrication conditions mainly as sintering temperature and Sn doping content are correlated with the phase, microstructure, infrared emissivity in and powder resistivity of indium tin oxides by means of x-ray diffraction, Fourier transform infrared, and transmission electron microscope. The optimum sintering temperature of 1350°C and Sn doping content 6∼8wt% are determined. The application of ITO in the military camouflage field is proposed. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Preparation and nonlinear optical properties of indium nanocrystals in sodium borosilicate glass by the sol–gel route

International Nuclear Information System (INIS)

Zhong, Jiasong; Xiang, Weidong; Zhao, Haijun; Chen, Zhaoping; Liang, Xiaojuan; Zhao, Wenguang; Chen, Guoxin

2012-01-01

Graphical abstract: The sodium borosilicate glass doped with indium nanocrystals have been successfully prepared by sol–gel methods. And the indium nanocrystals in tetragonal crystal system have formed uniformly in the glass, and the average diameter of indium nanocrystals is about 30 nm. The third-order optical nonlinear refractive index γ, absorption coefficient β, and susceptibility χ (3) of the glass are determined to be −4.77 × 10 −16 m 2 /W, 2.67 × 10 −9 m/W, and 2.81 × 10 −10 esu, respectively. Highlights: ► Indium nanocrystals embedded in glass matrix have been prepared by sol–gel route. ► The crystal structure and composition are investigated by XRD and XPS. ► Size and distribution of indium nanocrystals is determined by TEM. ► The third-order optical nonlinearity is investigated by using Z-scan technique. -- Abstract: The sodium borosilicate glass doped with indium nanocrystals have been successfully prepared by sol–gel route. The thermal stability behavior of the stiff gel is investigated by thermogravimetric (TG) and differential thermal (DTA) analysis. The crystal structure of the glass is characterized by X-ray powder diffraction (XRD). Particle composition is determined by X-ray photoelectron spectroscopy (XPS). Size and distribution of the nanocrystals are characterized by transmission electron microscopy (TEM) as well as high-resolution transmission electron microscopy (HRTEM). Results show that the indium nanocrystals in tetragonal crystal structure have formed in glass, and the average diameter is about 30 nm. Further, the glass is measured by Z-scan technique to investigate the nonlinear optical (NLO) properties. The third-order NLO coefficient χ (3) of the glass is determined to be 2.81 × 10 −10 esu. The glass with large third-order NLO coefficient is promising materials for applications in optical devices.

Determination of indium in geological materials by electrothermal-atomization atomic absorption spectrometry with a tungsten-impregnated graphite furance

Science.gov (United States)

Zhou, L.; Chao, T.T.; Meier, A.L.

1984-01-01

The sample is fused with lithium metaborate and the melt is dissolved in 15% (v/v) hydrobromic acid. Iron(III) is reduced with ascorbic acid to avoid its coextraction with indium as the bromide into methyl isobutyl ketone. Impregnation of the graphite furnace with sodium tungstate, and the presence of lithium metaborate and ascorbic acid in the reaction medium improve the sensitivity and precision. The limits of determination are 0.025-16 mg kg-1 indium in the sample. For 22 geological reference samples containing more than 0.1 mg kg-1 indium, relative standard deviations ranged from 3.0 to 8.5% (average 5.7%). Recoveries of indium added to various samples ranged from 96.7 to 105.6% (average 100.2%). ?? 1984.

Indium-111 labelled leucocyte scintigraphy in the diagnosis of inflammatory disease

International Nuclear Information System (INIS)

Roevekamp, M.H.

1982-01-01

The purpose of this study was to evaluate the diagnostic usefulness of indium-111 oxinate labelled autologous leucocytes in inflammatory disease. Chapter I provides an outline of the theoretical aspects of leucocyte labelling with indium-111 oxinate, as well as giving a description of the labelling method and scintigraphic technique and of the in-vitro and in-vivo studies performed to evaluate the method. In Chapter II details are given of the initial results obtained in a pilot study. A high false-negative rate led to modification of the labelling technique. The results obtained in patients suspected of intra-abdominal or retroperitoneal located inflammatory lesions are described in Chapter III. Chapter IV contains the description of an indium-111-leucocyte-99mTc-Sn-colloid computer-assisted subtraction technique for a better evaluation of patients suspected of an upper-abdominal inflammatory process. In Chapter V the study performed in patients after arterial reconstructive surgery is described, and the results obtained in patients suspected of an infected orthopaedic prosthesis are given in Chapter VI. Finally the characteristics of the different types of inflammatory responses is reviewed. (Auth.)

New quaternary thallium indium germanium selenide TlInGe2Se6: Crystal and electronic structure

Science.gov (United States)

Khyzhun, O. Y.; Parasyuk, O. V.; Tsisar, O. V.; Piskach, L. V.; Myronchuk, G. L.; Levytskyy, V. O.; Babizhetskyy, V. S.

2017-10-01

Crystal structure of a novel quaternary thallium indium germanium selenide TlInGe2Se6 was investigated by means of powder X-ray diffraction method. It was determined that the compound crystallizes in the trigonal space group R3 with the unit cell parameters a = 10.1798(2) Å, c = 9.2872(3) Å. The relationship with similar structures was discussed. The as-synthesized TlInGe2Se6 ingot was tested with X-ray photoelectron spectroscopy (XPS) and X-ray emission spectroscopy (XES). In particular, the XPS valence-band and core-level spectra were recorded for initial and Ar+ ion-bombarded surfaces of the sample under consideration. The XPS data allow for statement that the TlInGe2Se6 surface is rigid with respect to Ar+ ion-bombardment. Particularly, Ar+ ion-bombardment (3.0 keV, 5 min duration, ion current density fixed at 14 μA/cm2) did not cause substantial modifications of stoichiometry in topmost surface layers. Furthermore, comparison on a common energy scale of the XES Se Kβ2 and Ge Kβ2 bands and the XPS valence-band spectrum reveals that the principal contributions of the Se 4p and Ge 4p states occur in the upper and central portions of the valence band of TlInGe2Se6, respectively, with also their substantial contributions in other portions of the band. The bandgap energy of TlInGe2Se6 at the level of αg=103 cm-1 is equal to 2.38 eV at room temperature.

Studies on preparation and characterization of indium doped zinc ...

Indian Academy of Sciences (India)

Unknown

The preparation of indium doped zinc oxide films is discussed. ... XRD studies have shown a change in preferential orientation from (002) to .... at grain boundaries in the form of In(OH)3, hindering the .... Angular substrate to nozzle distance.

Synthesis of indium oxide cubic crystals by modified hydrothermal route for application in room temperature flexible ethanol sensors

International Nuclear Information System (INIS)

Seetha, M.; Meena, P.; Mangalaraj, D.; Masuda, Yoshitake; Senthil, K.

2012-01-01

Highlights: ► For the first time HMT is used in the preparation of indium oxide. ► HMT itself acts as base for the precursor and results in cubic indium hydroxide. ► Modified hydrothermal route used for the preparation of cubic indium oxide crystals. ► As a new approach a composite film synthesized with prepared indium oxide. ► Film showed good response to ethanol vapours with quick response and recovery times. - Abstract: Indium oxide cubic crystals were prepared by using hexamethylenetetramine and indium chloride without the addition of any structure directing agents. The chemical route followed in the present work was a modified hydrothermal synthesis. The average crystallite size of the prepared cubes was found to be 40 nm. A blue emission at 418 nm was observed at room temperature when the sample was excited with a 380 nm Xenon lamp. This emission due to oxygen vacancies made the material suitable for gas sensing applications. The synthesized material was made as a composite film with polyvinyl alcohol which was more flexible than the films prepared on glass substrates. This flexible film was used as a sensing element and tested with ethanol vapours at room temperature. The film showed fast response as well as recovery to ethanol vapours with a sensor response of about 1.4 for 100 ppm of the gas.

Transparent conductive electrodes of mixed TiO2−x–indium tin oxide for organic photovoltaics

KAUST Repository

Lee, Kyu-Sung

2012-05-22

A transparent conductive electrode of mixed titanium dioxide (TiO2−x)–indium tin oxide (ITO) with an overall reduction in the use of indium metal is demonstrated. When used in organic photovoltaicdevices based on bulk heterojunction photoactive layer of poly (3-hexylthiophene) and [6,6]-phenyl C61 butyric acid methyl ester, a power conversion efficiency of 3.67% was obtained, a value comparable to devices having sputtered ITO electrode. Surface roughness and optical efficiency are improved when using the mixed TiO2−x–ITO electrode. The consumption of less indium allows for lower fabrication cost of such mixed thin filmelectrode.

Small lead and indium inclusions in aluminium

International Nuclear Information System (INIS)

Johnson, E.; Hjemsted, K.; Schmidt, B.; Bourdelle, K.K.; Johansen, A.; Andersen, H.H.; Sarholt-Kristensen, L.

1992-01-01

This paper reports implantation of lead or indium into aluminum results in spontaneous phase separation and formation of lead or indium precipitates. The precipitates grow in topotactical alignment with the matrix, giving TEM images characterized by moire fringes. The size and density of the precipitates increase with increasing fluence until coalescence begins to occur. Implantation at elevated temperatures lead to formation of large precipitates with well developed facets. This is particularly significant for implantation above the bulk melting point of the implanted species. Melting and solidification have been followed by in-situ TEM heating and cooling experiments. Superheating up to ∼50 K above the bulk melting point has been observed, and the largest inclusions melt first. Melting is associated with only partial loss of facetting of the largest inclusion. Initial growth of the inclusions occurs by trapping of atoms retained in supersaturated solution. Further growth occurs by coalescence of neighboring inclusion in the liquid phase. Solidification is accompanied by a strong undercooling ∼30 K below the bulk melting point, where the smallest inclusions solidify first. Solidification is characterized by spontaneous restoration of the facets and the topotactical alignment

Influence of indium concentration and substrate temperature on the physical characteristics of chemically sprayed ZnO:In thin films deposited from zinc pentanedionate and indium sulfate

International Nuclear Information System (INIS)

Castaneda, L; Morales-Saavedra, O G; Cheang-Wong, J C; Acosta, D R; Banuelos, J G; Maldonado, A; Olvera, M de la L

2006-01-01

Chemically sprayed indium-doped zinc oxide thin films (ZnO:In) were deposited on glass substrates starting from zinc pentanedionate and indium sulfate. The influence of both the dopant concentration in the starting solution and the substrate temperature on the transport, morphology, composition, linear and nonlinear optical (NLO) properties of the ZnO:In thin films were studied. The structure of all the ZnO:In thin films was polycrystalline, and variation in the preferential growth with the indium content in the solution was observed: from an initial (002) growth in films with low In content, switching to a predominance of (101) planes for intermediate dopant regime, and finally turning to a (100) growth for heavily doped films. The crystallite size was found to decrease with doping concentration and range from 36 to 23 nm. The film composition and the dopant concentration were determined by Rutherford backscattering spectrometry; these results showed that the films are almost stoichiometric ZnO. The optimum deposition conditions leading to conductive and transparent ZnO:In thin films were also found. In this way a resistivity of 4 x 10 -3 Ω cm and an average transmittance in the visible spectra of 85%, with a (101) preferential growth, were obtained in optimized ZnO:In thin films

Advanced characterization techniques of nonuniform indium distribution within InGaN/GaN heterostructures grown by MOCVD

International Nuclear Information System (INIS)

Lu, D.; Florescu, D.I.; Lee, D.S.; Ramer, J.C.; Parekh, A.; Merai, V.; Li, S.; Begarney, M.J.; Armour, E.A.; Gardner, J.J.

2005-01-01

Nonuniform indium distribution within InGaN/GaN single quantum well (SQW) structures with nanoscale islands grown by metalorganic chemical vapor deposition (MOCVD) have been characterized by advanced characterization techniques. Robinson backscattered electron (BSE) measurements show cluster-like BSE contrast of high brightness regions, which are not centered at small dark pits in a SQW structure of spiral growth mode. By comparing with the secondary electron (SE) images, the bright cluster areas from the BSE images were found to have higher indium content compared to the surrounding dark areas. Temperature dependant photoluminescence (PL) measurement shows typical ''S-shape'' curve, which shows good correlation with nonuniform indium distribution from BSE measurement. Optical evaluation of the samples show increased PL slope efficiency of the spiral mode SQW, which can be attributed to the presence of Indium inhomogeneities. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Toxicity of indium arsenide, gallium arsenide, and aluminium gallium arsenide

International Nuclear Information System (INIS)

Tanaka, Akiyo

2004-01-01

Gallium arsenide (GaAs), indium arsenide (InAs), and aluminium gallium arsenide (AlGaAs) are semiconductor applications. Although the increased use of these materials has raised concerns about occupational exposure to them, there is little information regarding the adverse health effects to workers arising from exposure to these particles. However, available data indicate these semiconductor materials can be toxic in animals. Although acute and chronic toxicity of the lung, reproductive organs, and kidney are associated with exposure to these semiconductor materials, in particular, chronic toxicity should pay much attention owing to low solubility of these materials. Between InAs, GaAs, and AlGaAs, InAs was the most toxic material to the lung followed by GaAs and AlGaAs when given intratracheally. This was probably due to difference in the toxicity of the counter-element of arsenic in semiconductor materials, such as indium, gallium, or aluminium, and not arsenic itself. It appeared that indium, gallium, or aluminium was toxic when released from the particles, though the physical character of the particles also contributes to toxic effect. Although there is no evidence of the carcinogenicity of InAs or AlGaAs, GaAs and InP, which are semiconductor materials, showed the clear evidence of carcinogenic potential. It is necessary to pay much greater attention to the human exposure of semiconductor materials

Use of activable cations as tracers in groundwater hydrology. The case of DTPA-Indium

International Nuclear Information System (INIS)

Lumu, Badimbayi Matu.

1978-01-01

The possibilities of EDTA, CDTA and DTPA metallic complexes use as activable groundwater, tracers are discussed. Indium, which has good nuclear caracteristics for activation analysis and forms complexes of great stability with polyamino carboxylic acid has been for Laboratory and field studies. For corporative studies, Rhodomine B, a fluorescent tracer have been studied together with Indium complexes. In laboratory retention studies have been carried with In-EDTA, Iodine 131 and Rhodomine B, as tracers and bentonite, zeolite 13X and Dowex-1 and Dowex-50 as sorbents. As field studies, drainage evolution flow and resident time distribution of tracers substances in water, have been carried, under artificial rain conditions realized by aspersion. Results from field studies showed good characteristics of Indium Complexes especially in very absorbent medium (argilaceous limon) where their restitution balance were superior to that of Rhodomine B

Room temperature synthesis of indium tin oxide nanotubes with high precision wall thickness by electroless deposition

Directory of Open Access Journals (Sweden)

Mario Boehme

2011-02-01

Full Text Available Conductive nanotubes consisting of indium tin oxide (ITO were fabricated by electroless deposition using ion track etched polycarbonate templates. To produce nanotubes (NTs with thin walls and small surface roughness, the tubes were generated by a multi-step procedure under aqueous conditions. The approach reported below yields open end nanotubes with well defined outer diameter and wall thickness. In the past, zinc oxide films were mostly preferred and were synthesized using electroless deposition based on aqueous solutions. All these methods previously developed, are not adaptable in the case of ITO nanotubes, even with modifications. In the present work, therefore, we investigated the necessary conditions for the growth of ITO-NTs to achieve a wall thickness of around 10 nm. In addition, the effects of pH and reductive concentrations for the formation of ITO-NTs are also discussed.

An optimized antibody-chelator conjugate for imaging of carcinoembryonic antigen with indium-111

International Nuclear Information System (INIS)

Sumerdon, G.A.; Rogers, P.E.; Lombardo, C.M.; Schnobrich, K.E.; Melvin, S.L.; Tribby, I.I.E.; Stroupe, S.D.; Johnson, D.K.; Hobart, E.D.

1990-01-01

A monoclonal antibody to carcinoembryonic antigen showing minimal cross-reactivity with blood cells and normal tissues was derivatized with benzylisothiocyanate derivatives of EDTA and DTPA. Seven chelators per immunoglobulin could be incorporated without loss of immunoreactivity. The resulting conjugates, labeled with indium-111, showed low liver uptake in animals. A cold kit, comprising the DTPA conjugate at a molarity of antibody bound chelator exceeding 1 x 10 -4 M, gave radiochemical yields of indium labeled antibody of ≥ 95% and was stable for 1 yr. (author)

Indium-incorporation efficiency in semipolar (11-22) oriented InGaN-based light emitting diodes

Science.gov (United States)

Monavarian, Morteza; Metzner, Sebastian; Izyumskaya, Natalia; Okur, Serdal; Zhang, Fan; Can, Nuri; Das, Saikat; Avrutin, Vitaliy; Özgür, Ümit; Bertram, Frank; Christen, Jürgen; Morkoç, Hadis

2015-03-01

Reduced electric field in semipolar (1122) GaN/InGaN heterostructures makes this orientation attractive for high efficiency light emitting diodes. In this work, we investigated indium incorporation in semipolar (1122) GaN grown by metal-organic chemical vapor deposition on planar m-plane sapphire substrates. Indium content in the semipolar material was compared with that in polar c-plane samples grown under the same conditions simultaneously side by side on the same holder. The investigated samples incorporated dual GaN/InGaN/GaN double heterostructures with 3nm wide wells. In order to improve optical quality, both polar and semipolar templates were grown using an in-situ epitaxial lateral overgrowth (ELO) technique. Indium incorporation efficiency was derived from the comparison of PL spectra measured on the semipolar and polar structures at the highest excitation density, which allowed us to minimize the effect of quantum confined Stark effect on the emission wavelength. Our data suggests increased indium content in the semipolar material by up to 3.0%, from 15% In in c- GaN to 18% In in (1122) GaN.

Evaluated neutronic file for indium

International Nuclear Information System (INIS)

Smith, A.B.; Chiba, S.; Smith, D.L.; Meadows, J.W.; Guenther, P.T.; Lawson, R.D.; Howerton, R.J.

1990-01-01

A comprehensive evaluated neutronic data file for elemental indium is documented. This file, extending from 10 -5 eV to 20 MeV, is presented in the ENDF/B-VI format, and contains all neutron-induced processes necessary for the vast majority of neutronic applications. In addition, an evaluation of the 115 In(n,n') 116m In dosimetry reaction is presented as a separate file. Attention is given in quantitative values, with corresponding uncertainty information. These files have been submitted for consideration as a part of the ENDF/B-VI national evaluated-file system. 144 refs., 10 figs., 4 tabs

Synthesis of indium oxide cubic crystals by modified hydrothermal route for application in room temperature flexible ethanol sensors

Energy Technology Data Exchange (ETDEWEB)

Seetha, M., E-mail: seetha.phy@gmail.com [Department of Physics, SRM University, Kattankulathur, Kancheepuram Dt 603 203 (India); Meena, P. [Department of Physics, PSGR Krishnammal College for Women, Coimbatore 641 046 (India); Mangalaraj, D., E-mail: dmraj800@yahoo.com [DRDO-BU Centre for Life Sciences, Bharathiar University Campus, Coimbatore (India); Department of Nanoscience and Technology, Bharathiar University, Coimbatore 641 014 (India); Masuda, Yoshitake [National Institute of Advanced Industrial Science and Technology (AIST), Nagoya 463-8560 (Japan); Senthil, K. [School of Advanced Materials Science and Engineering, Sungkyunkwan University (Suwon Campus), Cheoncheon-dong 300, Jangan-gu, Suwon 440-746 (Korea, Republic of)

2012-03-15

Highlights: Black-Right-Pointing-Pointer For the first time HMT is used in the preparation of indium oxide. Black-Right-Pointing-Pointer HMT itself acts as base for the precursor and results in cubic indium hydroxide. Black-Right-Pointing-Pointer Modified hydrothermal route used for the preparation of cubic indium oxide crystals. Black-Right-Pointing-Pointer As a new approach a composite film synthesized with prepared indium oxide. Black-Right-Pointing-Pointer Film showed good response to ethanol vapours with quick response and recovery times. - Abstract: Indium oxide cubic crystals were prepared by using hexamethylenetetramine and indium chloride without the addition of any structure directing agents. The chemical route followed in the present work was a modified hydrothermal synthesis. The average crystallite size of the prepared cubes was found to be 40 nm. A blue emission at 418 nm was observed at room temperature when the sample was excited with a 380 nm Xenon lamp. This emission due to oxygen vacancies made the material suitable for gas sensing applications. The synthesized material was made as a composite film with polyvinyl alcohol which was more flexible than the films prepared on glass substrates. This flexible film was used as a sensing element and tested with ethanol vapours at room temperature. The film showed fast response as well as recovery to ethanol vapours with a sensor response of about 1.4 for 100 ppm of the gas.

Elastic properties of zinc, cadmium, bismuth, thallium, tin, lead and their binary alloys with indium

International Nuclear Information System (INIS)

Magomedov, A.M.

1986-01-01

Rates of propagation of longitudinal and transverse acoustic waves in samples as well as density of Tl, Pb, Sn, Bi, Cd, Zn and their binary alloys with indium are determined. The results obtained are used for calculation of elasticity constants of these materials. It is stated that concentration dependences of elasticity constants for indium alloys have non-linear character; negative deflection from the additive line is observed

Microstructure-mechanical property relationships for Al-Cu-Li-Zr alloys with minor additions of cadmium, indium or tin

Science.gov (United States)

Blackburn, L. B.; Starke, E. A., Jr.

1989-01-01

Minor amounts of cadmium, indium or tin were added to a baseline alloy with the nominal composition of Al-2.4Cu-2.4Li-0.15Zr. These elements were added in an attempt to increase the age-hardening response of the material such that high strengths could be achieved through heat-treatment alone, without the need for intermediate mechanical working. The alloy variant containing indium achieved a higher peak hardness in comparison to the other alloy variations, including the baseline material, when aged at temperatures ranging from 160 C to 190 C. Tensile tests on specimens peak-aged at 160 indicated the yield strength of the indium-bearing alloy increased by approximately 15 percent compared to that of the peak-aged baseline alloy. In addition, the yield strength obtained in the indium-bearing alloy was comparable to that reported for similar baseline material subjected to a 6 percent stretch prior to peak-aging at 190 C. The higher strength levels obtaied for the indium-bearing alloy are attributed to increased number densities and homogeneity of both the T1 and theta-prime phases, as determined by TEM studies.

First-principles analysis of structural and opto-electronic properties of indium tin oxide

Science.gov (United States)

Tripathi, Madhvendra Nath; Shida, Kazuhito; Sahara, Ryoji; Mizuseki, Hiroshi; Kawazoe, Yoshiyuki

2012-05-01

Density functional theory (DFT) and DFT + U (DFT with on-site Coulomb repulsion corrections) calculations have been carried out to study the structural and opto-electronic properties of indium tin oxide (ITO) for both the oxidized and reduced environment conditions. Some of the results obtained by DFT calculations differ from the experimental observations, such as uncertain indication for the site preference of tin atom to replace indium atom at b-site or d-site, underestimation of local inward relaxation in the first oxygen polyhedra around tin atom, and also the improper estimation of electronic density of states and hence resulting in an inappropriate optical spectra of ITO. These discrepancies of theoretical outcomes with experimental observations in ITO arise mainly due to the underestimation of the cationic 4d levels within standard DFT calculations. Henceforth, the inclusion of on-site corrections within DFT + U framework significantly modifies the theoretical results in better agreement to the experimental observations. Within this framework, our calculations show that the indium b-site is preferential site over d-site for tin atom substitution in indium oxide under both the oxidized and reduced conditions. Moreover, the calculated average inward relaxation value of 0.16 Å around tin atom is in good agreement with the experimental value of 0.18 Å. Furthermore, DFT + U significantly modify the electronic structure and consequently induce modifications in the calculated optical spectra of ITO.

Temperature dependence of InN film deposition by an RF plasma-assisted reactive ion beam sputtering deposition technique

International Nuclear Information System (INIS)

Shinoda, Hiroyuki; Mutsukura, Nobuki

2005-01-01

Indium nitride (InN) films were deposited on Si(100) substrates using a radiofrequency (RF) plasma-assisted reactive ion beam sputtering deposition technique at various substrate temperatures. The X-ray diffraction patterns of the InN films suggest that the InN films deposited at substrate temperatures up to 370 deg C were cubic crystalline InN; and at 500 deg C, the InN film was hexagonal crystalline InN. In a scanning electron microscope image of the InN film surface, facets of cubic single-crystalline InN grains were clearly observed on the InN film deposited at 370 deg C. The inclusion of metallic indium appeared on the InN film deposited at 500 deg C

In-Situ Growth and Characterization of Indium Tin Oxide Nanocrystal Rods

Directory of Open Access Journals (Sweden)

Yan Shen

2017-11-01

Full Text Available Indium tin oxide (ITO nanocrystal rods were synthesized in-situ by a vapor-liquid-solid (VLS method and electron beam evaporation technique. When the electron-beam gun bombarded indium oxide (In2O3 and tin oxide (SnO2 mixed sources, indium and tin droplets appeared and acted as catalysts. The nanocrystal rods were in-situ grown on the basis of the metal catalyst point. The nanorods have a single crystal structure. Its structure was confirmed by X-ray diffraction (XRD and transmission electron microscopy (TEM. The surface morphology was analyzed by scanning electron microscopy (SEM. During the evaporation, a chemical process was happened and an In2O3 and SnO2 solid solution was formed. The percentage of doped tin oxide was calculated by Vegard’s law to be 3.18%, which was in agreement with the mixture ratio of the experimental data. The single crystal rod had good semiconductor switch property and its threshold voltage of single rod was approximately 2.5 V which can be used as a micro switch device. The transmission rate of crystalline nanorods ITO film was over 90% in visible band and it was up to 95% in the blue green band as a result of the oxygen vacancy recombination luminescence.

High temperature dielectric studies of indium-substituted NiCuZn nanoferrites

Science.gov (United States)

Hashim, Mohd.; Raghasudha, M.; Shah, Jyoti; Shirsath, Sagar E.; Ravinder, D.; Kumar, Shalendra; Meena, Sher Singh; Bhatt, Pramod; Alimuddin; Kumar, Ravi; Kotnala, R. K.

2018-01-01

In this study, indium (In3+)-substituted NiCuZn nanostructured ceramic ferrites with a chemical composition of Ni0.5Cu0.25Zn0.25Fe2-xInxO4 (0.0 ≤ x ≤ 0.5) were prepared by chemical synthesis involving sol-gel chemistry. Single phased cubic spinel structure materials were prepared successfully according to X-ray diffraction and transmission electron microscopy analyses. The dielectric properties of the prepared ferrites were measured using an LCR HiTester at temperatures ranging from room temperature to 300 °C at different frequencies from 102 Hz to 5 × 106 Hz. The variations in the dielectric parameters ε‧ and (tanδ) with temperature demonstrated the frequency- and temperature-dependent characteristics due to electron hopping between the ions. The materials had low dielectric loss values in the high frequency range at all temperatures, which makes them suitable for high frequency microwave applications. A qualitative explanation is provided for the dependences of the dielectric constant and dielectric loss tangent on the frequency, temperature, and composition. Mӧssbauer spectroscopy was employed at room temperature to characterize the magnetic behavior.

Transparent indium-tin oxide/indium-gallium-zinc oxide Schottky diodes formed by gradient oxygen doping

Science.gov (United States)

Ho, Szuheng; Yu, Hyeonggeun; So, Franky

2017-11-01

Amorphous InGaZnO (a-IGZO) is promising for transparent electronics due to its high carrier mobility and optical transparency. However, most metal/a-IGZO junctions are ohmic due to the Fermi-level pinning at the interface, restricting their device applications. Here, we report that indium-tin oxide/a-IGZO Schottky diodes can be formed by gradient oxygen doping in the a-IGZO layer that would otherwise form an ohmic contact. Making use of back-to-back a-IGZO Schottky junctions, a transparent IGZO permeable metal-base transistor is also demonstrated with a high common-base gain.

Ellipsometric investigations of pyrolytically deposited thin indium oxide films

International Nuclear Information System (INIS)

Winkler, U.

1980-01-01

Ellipsometric measurements have been carried out of thin indium oxide films deposited pyrolytically on glass substrates. It was found that the roughness of the films affected the measuring results. Therefore, only after applying a two-layer model a reasonable interpretation of the measuring results became possible

Influence of disorder on the superconducting critical temperature in indium-opal nanocomposites

Science.gov (United States)

Zakharchuk, I.; Januzaj, A.; Mikhailin, N. Yu.; Traito, K. B.; Chernyaev, A. V.; Romanov, S. G.; Safonchik, M.; Shamshur, D. V.; Lähderanta, E.

2018-06-01

Transport properties of bulk indium-opal and indium-porous glass superconducting nanocomposites possessing moderate and strong disorder are investigated. A strongly nonmonotonous dependence of the global critical temperature Tc versus normal state conductivity of samples is found. The maximum, which is observed at moderate disorder, has Tc higher than that of clean bulk indium. The increasing part can be explained by the Eliashberg equations with disorder and an additional mechanism of interaction between superconducting and dielectric granules. The descending part of the maximum at higher disorder can be explained by the increasing of long-range Coulomb repulsion due to diffusion of charges. Negative slope in magnetic field dependence of resistivity and a peak in the temperature dependence of resistivity, observed in the sample near the proximity to the disorder-induced superconductor-insulator transition (SIT). A large difference between the onset temperature of superconducting fluctuations, Tcon , and global critical temperature Tc is found and considered in the framework of the weak multifractal theory. Slow time-logarithmic relaxation of the resistivity between Tc and Tcon is observed, which assumes existence of the precursor state near the SIT. This unusual state is discussed in the scope of the many-body localization theory.

Charge mobility increase in indium-molybdenum oxide thin films by hydrogen doping

Energy Technology Data Exchange (ETDEWEB)

Catalán, S.; Álvarez-Fraga, L. [Instituto de Ciencia de Materiales de Madrid, Consejo Superior de Investigaciones Científicas (ICMM-CSIC), Cantoblanco, E-28049 Madrid (Spain); Salas, E. [Spline CRG, ESRF, 38043 Grenoble (France); Ramírez-Jiménez, R. [Departamento de Física, Escuela Politécnica Superior, Universidad Carlos III de Madrid, Avenida Universidad 30, Leganés, 28911 Madrid (Spain); Rodriguez-Palomo, A.; Andrés, A. de [Instituto de Ciencia de Materiales de Madrid, Consejo Superior de Investigaciones Científicas (ICMM-CSIC), Cantoblanco, E-28049 Madrid (Spain); Prieto, C., E-mail: cprieto@icmm.csic.es [Instituto de Ciencia de Materiales de Madrid, Consejo Superior de Investigaciones Científicas (ICMM-CSIC), Cantoblanco, E-28049 Madrid (Spain)

2016-11-15

Highlights: • The charge mobility in IMO films is correlated with its hydrogen content. • The mobility behavior is explained by the presence of OH{sup −} groups in IMO films. • Mo{sup 4+} is identified in transparent conductive IMO by X-ray absorption spectroscopy. - Abstract: The increase of charge mobility in transparent conductive indium molybdenum oxide (IMO) films is correlated with the presence of hydroxyl groups. The introduction of H{sub 2} in the chamber during sputtering deposition compensates the excess charge introduced by cationic Mo doping of indium oxide either by oxygen or hydroxyl interstitials. Films present a linear increase of carrier mobility correlated with H{sub 2} content only after vacuum annealing. This behavior is explained because vacuum annealing favors the removal of oxygen interstitials over that of hydroxyl groups. Since hydroxyl groups offer lower effective charge and smaller lattice distortions than those associated with interstitial oxygen, this compensation mechanism offers the conditions for the observed increase in mobility. Additionally, the short-range order around molybdenum is evaluated by extended X-ray absorption fine structure (EXAFS) spectroscopy, showing that Mo{sup 4+} is placed at the In site of the indium oxide.

Work in progress: radionuclide imaging of indium-111-labeled eosinophils in mice

International Nuclear Information System (INIS)

Runge, V.M.; Rand, T.H.; Clanton, J.A.; Jones, J.P.; Colley, D.G.; Partain, C.L.; James, A.E. Jr.

1983-01-01

Eosinophils isolated from peritoneal exudates were labeled with indium-111-oxine and injected intravenously into sensitized mice. They became localized at sites of inflammation produced by intradermal injections of schistosomal antigen or Toxocara canis larvae, whereas labeled neutrophils did not. Intense uptake of eosinophils by normal spleen, liver, and bone marrow was noted, with tracer distribution effectively complete by 5 hours after injection. Indium-111-eosinophil studies appear to be quite sensitive to parasitic inflammatory reactions; in contrast, nonspecific inflammation such as that induced by turpentine causes localization of eosinophils, but to a lesser extent. This technique may be useful in the study of parasitic and allergic disease

Direct observation of indium compositional fluctuation in GaInN/GaN multi-quantum wells using an X-ray micro-beam from the 8-GeV storage ring

Energy Technology Data Exchange (ETDEWEB)

Miyajima, Takao; Uemura, Shigeaki; Kudo, Yoshihiro; Fuutagawa, Noriyuki [Materials Laboratories, Sony Corporation, 4-14-1 Asahi-cho, Atsugi, Kanagawa 243-0014 (Japan); Terada, Yasuko [Japan Synchrotron Radiation Research Institute, 1-1-1 Kouto, Sayo-cho, Sayo-gun, Hyogo 679-5198 (Japan)

2008-07-01

We measured the micrometer-scale fluctuation of the indium contents in a 50 {mu}m x 30 {mu}m region of annealed Ga{sub 0.8}In{sub 0.2}N/GaN multi quantum wells by mapping the counts of indium fluorescent X-rays excited by a 1.3 {mu}m x 3.8 {mu}m X-ray micro-beam. The mapping indicates that two distinct regions - indium-rich and indium-poor regions - are formed by the annealing. The indium contents in the island-shaped low-indium regions are 20% less than in the surrounding high-indium region. As the island-shaped low-indium regions clearly coincide with the low-radiative regions as observed by Hg-lamp-excited fluorescent microscopy, we believe that the low-radiative regions are a result not of indium segregation but of the generation of defects such as plane defects. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Study of the cerebro-spinal fluid circulation indium 111 labelled DTPA. Report of 300 cases

International Nuclear Information System (INIS)

Moreau, R.; Askienazy, S.; Mathieu, E.; Moretti, J.-L.

1976-01-01

A study of the C.S.F. circulation by intrathecal injection of radioactive tracers is a usual technique of neurological exploration. Indium-111 DTPA has numerous advantages for this type of study. It is a chelating agent, the renal clearance of which is rapid and which has no toxicity at the dose injected. Indium-111 is a cyclotron product with a half-life (2.8 days) compatible with the duration of the examination. Finally the dose of radioactivity delivered by this isotope is less than that of iodine 131, Technetium 99m, and ytterbium 169. In normal subjects after injection by the lumbar route, the average biological half-life measured by external counting lies between 20 and 28 hours. A study of the circulation of the C.S.F. is particularly useful in patients suspected of hydrocephalus. It permits finer diagnosis and shows the indication and type of by pass operation that may be necessary. An increase in the biological half-life of indium 111-DTPA seems to be a good indication for such an operation. An experience of 300 patients has shown the interest of the use of Indium 111-DTPA which now seems to be the best radio-isotope for the study of the subarachnoid space [fr

Deep subgap feature in amorphous indium gallium zinc oxide: Evidence against reduced indium

International Nuclear Information System (INIS)

Sallis, Shawn; Williams, Deborah S.; Quackenbush, Nicholas F.; Senger, Mikell; Woicik, Joseph C.; White, Bruce E.; Piper, Louis F.J.

2015-01-01

Amorphous indium gallium zinc oxide (a-IGZO) is the archetypal transparent amorphous oxide semiconductor. Despite the gains made with a-IGZO over amorphous silicon in the last decade, the presence of deep subgap states in a-IGZO active layers facilitate instabilities in thin film transistor properties under negative bias illumination stress. Several candidates could contribute to the formation of states within the band gap. Here, we present evidence against In + lone pair active electrons as the origin of the deep subgap features. No In + species are observed, only In 0 nano-crystallites under certain oxygen deficient growth conditions. Our results further support under coordinated oxygen as the source of the deep subgap states. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Anodic behavior of Al-Zn-In sacrificial anodes at different concentration of zinc and indium

Energy Technology Data Exchange (ETDEWEB)

Keyvani, Ahmad [Shahrekord Univ. (Iran, Islamic Republic of). Dept. of Materials Engineering; Tehran Univ. (Iran, Islamic Republic of). School of Metallurgy and Materials; Saremi, Mohsen [Tehran Univ. (Iran, Islamic Republic of). School of Metallurgy and Materials; Saeri, Mohammad Reza [Shahrekord Univ. (Iran, Islamic Republic of). Dept. of Materials Engineering

2012-12-15

Al-Zn-In anodes show better performance due to the beneficial effects of Zn and In on prevention of aluminum passivity and producing a homogeneous structure for uniform corrosion of the anodes. However, there are different views about the optimum concentration of each element in the anode. In this study, the anodic behavior of Al-Zn-In alloy with different concentrations of zinc from 1 to 6wt.% and indium from 0.01 to 0.05wt.% are studied. The NACE efficiency test and polarization are used in 3wt.% NaCl solution for corrosion characterization. The results showed that zinc and indium change the anode potential to more active potentials and improve the microstructure uniformity of anodes. The latter leads to more uniform corrosion. Optimum concentrations of zinc (5wt.%) and indium (0.02wt.%) were found in this respect. (orig.)

Effect of aluminum doping on the high-temperature stability and piezoresistive response of indium tin oxide strain sensors

International Nuclear Information System (INIS)

Gregory, Otto J.; You, Tao; Crisman, Everett E.

2005-01-01

Ceramic strain sensors based on reactively sputtered indium tin oxide (ITO) thin films doped with aluminum are being considered to improve the high-temperature stability and response. Ceramic strain sensors were developed to monitor the structural integrity of components employed in aerospace propulsion systems operating at temperatures in excess of 1500 deg C. Earlier studies using electron spectroscopy for chemical analysis (ESCA) studies indicated that interfacial reactions between ITO and aluminum oxide increase the stability of ITO at elevated temperature. The resulting ESCA depth files showed the presence of two new indium-indium peaks at 448.85 and 456.40 eV, corresponding to the indium 3d5 and 3d3 binding energies. These binding energies are significantly higher than those associated with stoichiometric indium oxide. Based on these studies, a combinatorial chemistry approach was used to screen large numbers of possible concentrations to optimize the stability and performance of Al-doped ceramic strain sensors. Scanning electron microscopy was used to analyze the combinatorial libraries in which varying amounts of aluminum were incorporated into ITO films formed by cosputtering from multiple targets. Electrical stability and piezoresistive response of these films were compared to undoped ITO films over the same temperature range

Determination of indium(III) with 3,4,5,6-tetrachlorogallein and cetylpyridinium chloride

International Nuclear Information System (INIS)

Mori, Itsuo; Fujita, Yoshikazu; Ida, Masako; Enoki, Takehisa

1976-01-01

Rapid and highly sensitive methods have been developed for the spectrophotometric and titrimetric determination of indium(III) with 3,4,5,6-tetrachlorogallein(3,4,5,6-T. Cl, Gal.) and cetylpyridinium chloride(CPC) in aqueous solutions of pH 4.2--5.2. The absorbance of the indium(III)-3,4,5,6-T. Cl. Gal. complex at 620 nm and the color change (pure blue - weak violetish red) were used to indicate the end point in the EDTA titration. The calibration curve for the spectrophotometry was linear in the range 0--45.0 μg In(III)/10 ml. According to Sandell's expression, the sensitivity was 0.0032 μg In(III)/cm 2 for an absorbance of 0.001. To the solution containing less than 45.0 μg of indium(III), 2.0 ml of 1.0x10 -2 M CPC solution, 3.0 ml of Walpole buffer solution(pH 4.4; acetic acid-sodium acetate), and 2.0 ml of 1.0x10 -3 M 3,4,5,6-T.Cl.Gal. methanol solution were added and the volume was made up to 10.0 ml with water. The solution was kept at (20--25) 0 C for 30 minutes and then the absorbance was measured at 620 nm against the reagent blank. The mole ratio of indium(III), 3,4,5,6-T.Cl.Gal. and CPC in the complex was estimated to be 1 : 2 : 2 by the continuous variation and the mole ratio methods. (auth.)

Indium Sulfide and Indium Oxide Thin Films Spin-Coated from Triethylammonium Indium Thioacetate Precursor for n-Channel Thin Film Transistor

Energy Technology Data Exchange (ETDEWEB)

Tung, Duy Dao; Jeong, Hyun Dam [Chonnam Natioal University, Gwangju (Korea, Republic of)

2014-09-15

The In{sub 2}S{sub 3} thin films of tetragonal structure and In{sub 2}O{sub 3} films of cubic structure were synthesized by a spin coating method from the organometallic compound precursor triethylammonium indium thioacetate ([(Et){sub 3}NH]+ [In(SCOCH{sub 3}){sub 4}]''-; TEA-InTAA). In order to determine the electron mobility of the spin-coated TEA-InTAA films, thin film transistors (TFTs) with an inverted structure using a gate dielectric of thermal oxide (SiO{sub 2}) was fabricated. These devices exhibited n-channel TFT characteristics with a field-effect electron mobility of 10.1 cm''2 V''-1s''-1 at a curing temperature of 500 o C, indicating that the semiconducting thin film material is applicable for use in low-cost, solution-processed printable electronics.

Indium 111 WBC scan in local and systemic fungal infections

International Nuclear Information System (INIS)

Haseman, M.K.; Blake, K.; McDougall, I.R.

1984-01-01

We describe two patients-one with a systemic fungal infection and one with a localized form-who had strikingly abnormal indium 111 leukocyte (WBC) scans. The patient with systemic disease had an abnormal WBC scan before lesions became clinically apparent

Efficient Indium-Mediated Dehalogenation of Aromatics in Ionic Liquid Media

Directory of Open Access Journals (Sweden)

Flavia C. Zacconi

2012-12-01

Full Text Available An efficient indium-mediated dehalogenation reaction of haloaromatics and haloheteroaromatics in ionic liquids has been studied. This method is simple and effective in the presence of [bmim]Br. Furthermore, this methodology is environmentally friendly compared with conventional ones.

Current status of indium-111 labeled bleomycin for tumor detection

International Nuclear Information System (INIS)

Taylor, R.D.; Blahd, W.H.

1975-01-01

The advantages and disadvantages of 111 In-labeled bleomycin for tumor detection are briefly mentioned. Indium-111 labeled bleomycin does localize in human tumors. However, its role in tumor detection and staging as compared with 67 Ga is still somewhat controversial

In{sub 6}Se{sub 7} thin films by heating thermally evaporated indium and chemical bath deposited selenium multilayers

Energy Technology Data Exchange (ETDEWEB)

Ornelas, R.E.; Avellaneda, D. [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, San Nicolas de los Garza, Nuevo Leon-66450 (Mexico); Shaji, S. [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, San Nicolas de los Garza, Nuevo Leon-66450 (Mexico); Universidad Autonoma de Nuevo Leon-CIIDIT, Apodaca, N.L (Mexico); Castillo, G.A.; Roy, T.K. Das [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, San Nicolas de los Garza, Nuevo Leon-66450 (Mexico); Krishnan, B., E-mail: kbindu_k@yahoo.com [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, San Nicolas de los Garza, Nuevo Leon-66450 (Mexico); Universidad Autonoma de Nuevo Leon-CIIDIT, Apodaca, N.L (Mexico)

2012-05-15

Indium selenide (In{sub 6}Se{sub 7}) thin films were prepared via selenization of thermally evaporated indium thin films by dipping in sodium selenosulphate solution followed by annealing in nitrogen atmosphere. First, indium was thermally evaporated on glass substrate. Then, the indium coated glass substrates were dipped in a solution containing 80 ml 0.125 M sodium selenosulphate and 1.5 ml dilute acetic acid (25%) for 5 min. Glass/In-Se layers were annealed at 200-400 Degree-Sign C in nitrogen atmosphere (0.1 Torr) for 30 min. X-ray diffraction studies showed the formation of monoclinic In{sub 6}Se{sub 7}. Morphology of the thin films formed at different conditions was analyzed using Scanning electron microscopy. The elemental analysis was done using Energy dispersive X-ray detection. Electrical conductivity under dark and illumination conditions was evaluated. Optical band gap was computed using transmittance and reflectance spectra. The band gap value was in the range 1.8-2.6 eV corresponding to a direct allowed transition. We studied the effect of indium layer thickness and selenium deposition time on the structure, electrical and optical properties of In{sub 6}Se{sub 7} thin films.

Indium-111 tropolone, a new high-affinity platelet label: preparation and evaluation of labeling parameters

International Nuclear Information System (INIS)

Dewanjee, M.K.; Rao, S.A.; Didisheim, P.

1981-01-01

Platelets were isolated with a new neutral, lipid-soluble metal complex of indium-111 and tropolone. Unlike oxine, which must be dissolved in ethyl alcohol, tropolone is soluble saline. Platelet labeling with In-111 tropolone can be performed in both acid-citrate-dextrose (ACD)-plasma and ACD-saline media within two hours' time. Labeling efficiency has been 80-90% in ACD-saline and 60-70% in the ACD-plasma medium. Optimum concentrations for the labeling of platelets with In-111 tropolone were 5 micrograms/ml in ACD-saline and 10 micrograms/ml in ACD-plasma, using a 15-min incubation at room temperature. A kit formulation for convenient routine preparation of In-111-labeled platelets has been developed. Seven parameters of platelet labeling were studied: concentration of tropolone, citrate, plasma proteins, and calcium ions; also platelet density, temperature, and pH of incubation medium. Their effects on the mechanism of platelet labeling with lipid-soluble tracers are discussed

(111)Indium Labelling of Recombinant Activated Coagulation Factor VII

DEFF Research Database (Denmark)

Nalla, Amarnadh; Buch, Inge; Sigvardt, Maibritt

2012-01-01

The aim of this study is to investigate whether (111)Indium-labelled recombinant FVIIa (rFVIIa) could be a potential radiopharmaceutical for localization of bleeding sources. DTPA-conjugated rFVIIa was radiolabelled with (111)In chloride. In vitro binding efficiency of (111)In-DTPA-rFVIIa to F1A2...

Electrical properties of vacuum-annealed titanium-doped indium oxide films

NARCIS (Netherlands)

Yan, L.T.; Rath, J.K.; Schropp, R.E.I.

2011-01-01

Titanium-doped indium oxide (ITiO) films were deposited on Corning glass 2000 substrates at room temperature by radio frequency magnetron sputtering followed by vacuum post-annealing. With increasing deposition power, the as-deposited films showed an increasingly crystalline nature. As-deposited

Compton scattering studies of the electron momentum distribution in indium phosphide

CERN Document Server

Deb, A; Guin, R; Chatterjee, A K

1999-01-01

The electron momentum anisotropy of indium phosphide has been studied by measuring the directional Compton profiles of indium phosphide single crystals with the use of radiation from an sup 2 sup 4 sup 1 Am gamma source. Three different samples, cut along the [100], [110] and [111] planes, were used. The experimental anisotropy has been compared with the results based on the linear combination of Gaussian orbitals (LCGO) method. The agreement is very good with our theoretical results. It is found that the extrema appearing in the dependences on q of the anisotropies have an intimate connection with the bonding properties of the semiconductor. A self-consistent, all-electron, local density calculation for the partial density of states, total density of states and the charge analysis is also presented here.

Radioassay process using an indium-8-hydroxyquinoline

International Nuclear Information System (INIS)

Goedemans, W.T.

1981-01-01

There is disclosed an in vivo radioassay process in which a radioactive chelate of indium and an 8-hydroxyquinoline is introduced into a warmblooded animal having an inflammatory reaction in an area in which the chelate would not accumulate to the same extent if the inflammation were not present. The chelate gathers in the inflamed area, for instance, in a body abscess and its location is determined by radio surveying the body by an external imaging technique. (author)

Self-assembly surface modified indium-tin oxide anodes for single-layer light-emitting diodes

CERN Document Server

Morgado, J; Charas, A; Matos, M; Alcacer, L; Cacialli, F

2003-01-01

We study the effect of indium-tin oxide surface modification by self assembling of highly polar molecules on the performance of single-layer light-emitting diodes (LEDs) fabricated with polyfluorene blends and aluminium cathodes. We find that the efficiency and light-output of such LEDs is comparable to, and sometimes better than, the values obtained for LEDs incorporating a hole injection layer of poly(3,4-ethylene dioxythiophene) doped with polystyrene sulphonic acid. This effect is attributed to the dipole-induced work function modification of indium-tin oxide.

Post-deposition annealing effects in RF reactive magnetron sputtered indium tin oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Martinez, M A; Herrero, J; Gutierrez, M T [Inst. de Energias Renovables (CIEMAT), Madrid (Spain)

1992-05-01

Indium tin oxide films have been grown by RF reactive magnetron sputtering. The influence of the deposition parameters on the properties of the films has been investigated and optimized, obtaining a value for the figure of merit of 6700 ({Omega} cm){sup -1}. As-grown indium tin oxide films were annealed in vacuum and O{sub 2} atmosphere. After these heat treatments the electro-optical properties were improved, with values for the resistivity of 1.9x10{sup -4} {Omega} cm and the figure of merit of 26700 ({Omega} cm){sup -1}. (orig.).

Self-assembly surface modified indium-tin oxide anodes for single-layer light-emitting diodes

International Nuclear Information System (INIS)

Morgado, Jorge; Barbagallo, Nunzio; Charas, Ana; Matos, Manuel; Alcacer, Luis; Cacialli, Franco

2003-01-01

We study the effect of indium-tin oxide surface modification by self assembling of highly polar molecules on the performance of single-layer light-emitting diodes (LEDs) fabricated with polyfluorene blends and aluminium cathodes. We find that the efficiency and light-output of such LEDs is comparable to, and sometimes better than, the values obtained for LEDs incorporating a hole injection layer of poly(3,4-ethylene dioxythiophene) doped with polystyrene sulphonic acid. This effect is attributed to the dipole-induced work function modification of indium-tin oxide

Deep subgap feature in amorphous indium gallium zinc oxide: Evidence against reduced indium

Energy Technology Data Exchange (ETDEWEB)

Sallis, Shawn; Williams, Deborah S. [Materials Science and Engineering, Binghamton University, Binghamton, New York, 13902 (United States); Quackenbush, Nicholas F.; Senger, Mikell [Department of Physics, Applied Physics and Astronomy, Binghamton University, Binghamton, New York, 13902 (United States); Woicik, Joseph C. [Materials Science and Engineering Laboratory, National Institute of Standards and Technology, Gaithersburg, Maryland, 20899 (United States); White, Bruce E.; Piper, Louis F.J. [Materials Science and Engineering, Binghamton University, Binghamton, New York, 13902 (United States); Department of Physics, Applied Physics and Astronomy, Binghamton University, Binghamton, New York, 13902 (United States)

2015-07-15

Amorphous indium gallium zinc oxide (a-IGZO) is the archetypal transparent amorphous oxide semiconductor. Despite the gains made with a-IGZO over amorphous silicon in the last decade, the presence of deep subgap states in a-IGZO active layers facilitate instabilities in thin film transistor properties under negative bias illumination stress. Several candidates could contribute to the formation of states within the band gap. Here, we present evidence against In{sup +} lone pair active electrons as the origin of the deep subgap features. No In{sup +} species are observed, only In{sup 0} nano-crystallites under certain oxygen deficient growth conditions. Our results further support under coordinated oxygen as the source of the deep subgap states. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Physical properties of pyrolytically sprayed tin-doped indium oxide coatings

NARCIS (Netherlands)

Haitjema, H.; Elich, J.J.P.

1991-01-01

The optical and electrical properties of tin-doped indium oxide coatings obviously depend on a number of production parameters. This dependence has been studied to obtain a more general insight into the relationships between the various coating properties. The coatings have been produced by spray

Growth and shape of indium islands on molybdenum at micro-roughened spots created by femtosecond laser pulses

Science.gov (United States)

Ringleb, F.; Eylers, K.; Teubner, Th.; Schramm, H.-P.; Symietz, C.; Bonse, J.; Andree, S.; Heidmann, B.; Schmid, M.; Krüger, J.; Boeck, T.

2017-10-01

Indium islands on molybdenum coated glass can be grown in ordered arrays by surface structuring using a femtosecond laser. The effect of varying the molybdenum coated glass substrate temperature and the indium deposition rate on island areal density, volume and geometry is investigated and evaluated in a physical vapor deposition (PVD) process. The joined impact of growth conditions and spacing of the femtosecond laser structured spots on the arrangement and morphology of indium islands is demonstrated. The results yield a deeper understanding of the island growth and its precise adjustment to industrial requirements, which is indispensable for a technological application of such structures at a high throughput, for instance as precursors for the preparation of Cu(In,Ga)Se2 micro concentrator solar cells.

Composition dependence of the thermodynamic activity and lattice parameter of zeta nickel-indium

International Nuclear Information System (INIS)

Bhattacharya, B.; Masson, D.B.

1976-01-01

The vapor pressure of indium over six alloys in the zeta phase of the nickel-indium system was measured by the method of atomic absorption. Values of thermodynamic activity were calculated from the vapor pressure, and partial heat and entropy of indium were calculated from the temperature coefficients. The lattice parameters of the hexagonal B8 2 unit cell of all alloys were calculated from X-ray diffraction powder patterns. It was found that the a lattice parameter passed through a minimum at the same composition that the excess chemical potential showed a sharp change of slope, when graphed as a function of composition. These effects were similar to those observed previously which have been attributed to overlap by the Fermi surface of a Brillouin zone face. In the present case they were attributed to overlap of the Fermi surface across faces tentatively identified as the [110] faces of the Brillouin zone of the B8 2 structure. The influence of substitutional disorder was also considered as a cause of the thermodynamic effects, but this was rejected because it does not explain the minimum in lattice parameter. (Auth.)

Efficient and Selective Debromination of vic-Dibromides to Alkenes Using CoCl2·6H2O/Indium System

International Nuclear Information System (INIS)

Yoo, Byung Woo; Kim, Seo Hee; Min, Ga Hong

2012-01-01

We have found that vic-dibromides treated with CoCl 2 ·6H 2 O/indium system in methanol are efficiently converted into the corresponding alkenes in high yields under mild conditions. Although the scope and limitations of this method have not been fully established, it is expected to be a useful and efficient alternative to the existing methods for the debromination of vic-dibromides. There is always considerable interest in the search for more efficient and selective procedures for the debromination of vic-dibromides. The reduction of CoCl 2 to low-valent cobalt species and the synthetic utility of such species are well documented in the literature. Generally, reducing agents, such as zinc and magnesium, are used for the reduction of CoCl 2 . Because indium and zinc closely resemble each other in several aspects, including first ionization, we considered that a combination of CoCl 2 ·6H 2 O with indium could facilitate the reductive debromination of vic-dibromides under mild conditions. As in the case of zinc, the reduction potential of indium is not highly negative (In: E o , In +3 /In = -0.345 V; Zn: E o , Zn: +2 /Zn = -0.763 V): thus, indium is not sensitive to water and does not form oxides readily in air. In recent years, indium metal has been the subject of active interest because of its unique properties such as low toxicity and high stability in water and air compared to other metals. In connection with our interest in exploring the utility of low-valent metal reagents for organic transformations, we herein wish to report an efficient and chemoselective method for the debromination of vic-dibromides to alkenes using CoCl 2 ·6H 2 O/indium system at room temperature

Identification of photoluminescence P line in indium doped silicon as In{sub Si}-Si{sub i} defect

Energy Technology Data Exchange (ETDEWEB)

Lauer, Kevin, E-mail: klauer@cismst.de; Möller, Christian [CiS Forschungsinstitut für Mikrosensorik und Photovoltaik GmbH, Konrad-Zuse-Str. 14, 99099 Erfurt (Germany); Schulze, Dirk [TU Ilmenau, Institut für Physik, Weimarer Str. 32, 98693 Ilmenau (Germany); Ahrens, Carsten [Infineon Technologies AG, Am Campeon 1-12, 85579 Neubiberg (Germany)

2015-01-15

Indium and carbon co-implanted silicon was investigated by low-temperature photoluminescence spectroscopy. A photoluminescence peak in indium doped silicon (P line) was found to depend on the position of a silicon interstitial rich region, the existence of a SiN{sub x}:H/SiO{sub x} stack and on characteristic illumination and annealing steps. These results led to the conclusion that silicon interstitials are involved in the defect and that hydrogen impacts the defect responsible for the P line. By applying an unique illumination and annealing cycle we were able to link the P line defect with a defect responsible for degradation of charge carrier lifetime in indium as well as boron doped silicon. We deduced a defect model consisting of one acceptor and one silicon interstitial atom denoted by A{sub Si}-Si{sub i}, which is able to explain the experimental data of the P line as well as the light-induced degradation in indium and boron doped silicon. Using this model we identified the defect responsible for the P line as In{sub Si}-Si{sub i} in neutral charge state and C{sub 2v} configuration.

INDIUM AND ZINC MEDIATED ONE-ATOM CARBOCYCLE ENLARGEMENT IN WATER. (R822668)

Science.gov (United States)

AbstractSix-, seven-, eight-membered rings are enlarged by one carbon-atom into seven-, eight- and nine-membered ring derivatives respectively, via indium or zinc mediated reactions in aqueous medium.

Cooperative adsorption of critical metal ions using archaeal poly-γ-glutamate.

Science.gov (United States)

Hakumai, Yuichi; Oike, Shota; Shibata, Yuka; Ashiuchi, Makoto

2016-06-01

Antimony, beryllium, chromium, cobalt (Co), gallium (Ga), germanium, indium (In), lithium, niobium, tantalum, the platinoids, the rare-earth elements (including dysprosium, Dy), and tungsten are generally regarded to be critical (rare) metals, and the ions of some of these metals are stabilized in acidic solutions. We examined the adsorption capacities of three water-soluble functional polymers, namely archaeal poly-γ-glutamate (L-PGA), polyacrylate (PAC), and polyvinyl alcohol (PVA), for six valuable metal ions (Co(2+), Ni(2+), Mn(2+), Ga(3+), In(3+), and Dy(3+)). All three polymers showed apparently little or no capacity for divalent cations, whereas L-PGA and PAC showed the potential to adsorb trivalent cations, implying the beneficial valence-dependent selectivity of anionic polyelectrolytes with multiple carboxylates for metal ions. PVA did not adsorb metal ions, indicating that the crucial role played by carboxyl groups in the adsorption of crucial metal ions cannot be replaced by hydroxyl groups under the conditions. In addition, equilibrium studies using the non-ideal competitive adsorption model indicated that the potential for L-PGA to be used for the removal (or collection) of water-soluble critical metal ions (e.g., Ga(3+), In(3+), and Dy(3+)) was far superior to that of any other industrially-versatile PAC materials.

Clinical evaluation of the platelet scintigraphy using indium-111 oxine

International Nuclear Information System (INIS)

Ishikawa, Nobuyoshi; Takeda, Tohoru; Nakajima, Kohtaroh; Satoh, Motohiro; Akisada, Masayoshi; Ijima, Hiroshi

1988-01-01

The clinical usefulness of autologous platelets labeled with Indium-111 oxine was evaluated by scintigraphy as a diagnostic procedure for the detection of various thrombotic disorders as well as in different aneurysms. The positivity was found to be satisfactory (80.0 %) in cases of aortic aneurysm while thoracic aneurysm showed comparatively poor accumulation. High positivity was also demonstrated in deep vein thrombosis. The complimentary role of this method for intracardiac thrombi to echocardiography was noted. The labeling procedure of indium-111 oxine was fairly easy to perform and the activity of labeled platelets was sustained enough to yield good results. In one case scintigraphy was performed successfully after 19 hours of angiography when a hot area of labeled platelets was seen at the puncture site. This method was therefore varified to be a sensitive and reliable method in the assessment of thrombus activity, and as it demonstrates the activity, its helpfulness in the conservative treatment of these disorders is warranted. (author)

Diagnostic compositions containing a chelate of radioactive indium and 8-hydroxyquinoline

International Nuclear Information System (INIS)

Goedemans, W.T.

1981-01-01

There are disclosed aqueous, radioassaying solutions of a chelate of radioactive indium and an 8-hydroxyquinoline, having an essential absence of an organic solvent, e.g., alcohol or chloroform. The solutions are useful in radioassaying warmblooded animals. (author)

Silver-indium-cadmium control rod behaviour during a severe reactor accident

International Nuclear Information System (INIS)

Bowsher, B.R.; Jenkins, R.A.; Nichols, A.L.; Rowe, N.A.; Simpson, J.A.H.

1986-04-01

An alloy of silver, indium and cadmium is commonly used as control rod material in pressurised water reactors (PWRs). The behaviour of this alloy has been studied in a series of experiments using an induction furnace to achieve temperatures up to 1900K. The aerosols released from overheated clad and unclad control rod samples have been characterised in both steam and inert atmospheres. Mass balance experiments have been undertaken to determine the distribution of the control rod alloy constituents following rupture of the cladding, and this work has been supported by thermogravimetric studies of silver-indium mixtures. Metallographic studies were also undertaken to assess the failure mode of the stainless steel cladding and the interaction of the molten alloy with Zircaloy. The results of this work are discussed in terms of aerosol/vapour behaviour during severe reactor accidents. (author)

Related electrical, superconducting and structural characteristics of low temperature indium films

International Nuclear Information System (INIS)

Belevtsev, B.I.; Pilipenko, V.V.; Yatsuk, L.Ya.

1981-01-01

Reported are results of a complex study of electrical, superconducting and structural properties of indium films vacuum evaporated onto a liquid helium-cooled substrate. Structural electron diffraction investigations gave a better insight into the general features of the annealing during the warming-up of cold-deposited films. It is found that the annealing of indium films to about 80 to 100 K entails an irreversible growth of interplanar separations due to decreasing inhomogeneous microstresses. As the films are warmed from 100 to 300 K, the principal annealing processes are determined by crystallite growth and development of dominating orientation. The changes in the residual resistance and in Tsub(c) with warming the cold-deported films are explained on the base of structural data obtained. In particular, a direct relationship is revealed between the crystallite size and Tsub(c) [ru

Surface characterization of sol–gel derived indium tin oxide films on ...

Indian Academy of Sciences (India)

Unknown

, India ... 1. Introduction. Indium tin oxide (ITO) coating on glass is an important item in the field ..... In addition, contamination of carbon from environment cannot be ruled ..... processing of ceramics, glasses and composites (eds) L L. Hench and ...

Growth and Characterization of Indium Doped ZnO Nano wires Using Thermal Evaporation Method

International Nuclear Information System (INIS)

Abrar Ismardi; Dee, C.F.; Majlis, B.Y.

2011-01-01

Indium doped ZnO nano wires were grown on silicon substrate using vapor thermal deposition method without using any catalyst. Morphological structures were extensively investigated using field emission scanning electron microscopy (FESEM) and show that the nano wires have uniformly hexagonal nano structures with diameters less than 100 nm and lengths from one to a few microns. The sample was measured for elemental composition with energy dispersive X-ray (EDX) spectroscopy, Zn, In and O elements were found on the sample. XRD spectrum of indium doped ZnO nano wires revealed that the nano wires have a high crystalline structure. (author)

The n-type conduction of indium-doped Cu{sub 2}O thin films fabricated by direct current magnetron co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Cai, Xing-Min; Su, Xiao-Qiang; Ye, Fan, E-mail: yefan@szu.edu.cn; Wang, Huan; Tian, Xiao-Qing; Zhang, Dong-Ping; Fan, Ping; Luo, Jing-Ting; Zheng, Zhuang-Hao; Liang, Guang-Xing [Institute of Thin Film Physics and Applications, School of Physical Science and Technology and Shenzhen Key Laboratory of Sensor Technology, Shenzhen University, Shenzhen 518060 (China); Roy, V. A. L. [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Kowloon Tong, Hong Kong (China)

2015-08-24

Indium-doped Cu{sub 2}O thin films were fabricated on K9 glass substrates by direct current magnetron co-sputtering in an atmosphere of Ar and O{sub 2}. Metallic copper and indium disks were used as the targets. X-ray diffraction showed that the diffraction peaks could only be indexed to simple cubic Cu{sub 2}O, with no other phases detected. Indium atoms exist as In{sup 3+} in Cu{sub 2}O. Ultraviolet-visible spectroscopy showed that the transmittance of the samples was relatively high and that indium doping increased the optical band gaps. The Hall effect measurement showed that the samples were n-type semiconductors at room temperature. The Seebeck effect test showed that the films were n-type semiconductors near or over room temperature (<400 K), changing to p-type at relatively high temperatures. The conduction by the samples in the temperature range of the n-type was due to thermal band conduction and the donor energy level was estimated to be 620.2–713.8 meV below the conduction band. The theoretical calculation showed that indium doping can raise the Fermi energy level of Cu{sub 2}O and, therefore, lead to n-type conduction.

Indium oxide thin film based ammonia gas and ethanol vapour sensor

Indian Academy of Sciences (India)

Unknown

acetone and dried under an electric lamp (100 W). Thin films of indium oxide ... A λ-19, UV–VIS Spectrophotometer (Perkin Elmer, USA) was used for measuring .... tion of ammonia is observed through glowing of LED. LM3914, LED driver is ...

Diagnosis of deep vein thrombosis using autologous indium-III-labelled platelets

International Nuclear Information System (INIS)

Fenech, A.; Hussey, J.K.; Smith, F.W.; Dendy, P.P.; Bennett, B.; Douglas, A.S.

1981-01-01

Forty-eight patients who had undergone surgical reduction of a fractured neck of femur or in whom deep vein thrombosis was suspected clinically were studied by ascending phlebography and imaging after injection of autologous indium-III-labelled platelets to assess the accuracy and value of the radioisotopic technique in diagnosing deep vein thrombosis. Imaging was performed with a wide-field gammacamera linked with data display facilities. Phlebography showed thrombi in 26 out of 54 limbs examined and a thrombus in the inferior vena cava of one patient; imaging the labelled platelets showed the thrombi in 24 of the 26 limbs and the thrombus in the inferior vena cava. The accumulation of indium-III at sites corresponding to those at which venous thrombi have been shown phlebographically indicates that this radioisotopic technique is a useful addition to methods already available for the detection of deep vein thrombosis. (author)

Diagnosis of deep vein thrombosis using autologous indium-III-labelled platelets

Energy Technology Data Exchange (ETDEWEB)

Fenech, A.; Hussey, J.K.; Smith, F.W.; Dendy, P.P.; Bennett, B.; Douglas, A.S. (Aberdeen Univ. (UK))

1981-03-28

Forty-eight patients who had undergone surgical reduction of a fractured neck of femur or in whom deep vein thrombosis was suspected clinically were studied by ascending phlebography and imaging after injection of autologous indium-III-labelled platelets to assess the accuracy and value of the radioisotopic technique in diagnosing deep vein thrombosis. Imaging was performed with a wide-field gamma camera linked with data display facilities. Phlebography showed thrombi in 26 out of 54 limbs examined and a thrombus in the inferior vena cava of one patient; imaging the labelled platelets showed the thrombi in 24 of the 26 limbs and the thrombus in the inferior vena cava. The accumulation of indium-III at sites corresponding to those at which venous thrombi have been shown phlebographically indicates that this radioisotopic technique is a useful addition to methods already available for the detection of deep vein thrombosis.

Double-layer indium doped zinc oxide for silicon thin-film solar cell prepared by ultrasonic spray pyrolysis

International Nuclear Information System (INIS)

Jiao Bao-Chen; Zhang Xiao-Dan; Wei Chang-Chun; Sun Jian; Ni Jian; Zhao Ying

2011-01-01

Indium doped zinc oxide (ZnO:In) thin films were prepared by ultrasonic spray pyrolysis on corning eagle 2000 glass substrate. 1 and 2 at.% indium doped single-layer ZnO:In thin films with different amounts of acetic acid added in the initial solution were fabricated. The 1 at.% indium doped single-layers have triangle grains. The 2 at.% indium doped single-layer with 0.18 acetic acid adding has the resistivity of 6.82×10 −3 Ω·cm and particle grains. The double-layers structure is designed to fabricate the ZnO:In thin film with low resistivity (2.58×10 −3 Ω·cm) and good surface morphology. It is found that the surface morphology of the double-layer ZnO:In film strongly depends on the substrate-layer, and the second-layer plays a large part in the resistivity of the double-layer ZnO:In thin film. Both total and direct transmittances of the double-layer ZnO:In film are above 80% in the visible light region. Single junction a-Si:H solar cell based on the double-layer ZnO:In as front electrode is also investigated. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Studies on the optoelectronic properties of the thermally evaporated tin-doped indium oxide nanostructures

Energy Technology Data Exchange (ETDEWEB)

Pan, Ko-Ying [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300, Taiwan, ROC (China); Lin, Liang-Da [Institute of Materials Science and Nanotechnology, Chinese Culture University, Taipei 111, Taiwan, ROC (China); Chang, Li-Wei [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300, Taiwan, ROC (China); Shih, Han C., E-mail: hcshih@mx.nthu.edu.tw [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300, Taiwan, ROC (China); Institute of Materials Science and Nanotechnology, Chinese Culture University, Taipei 111, Taiwan, ROC (China)

2013-05-15

Indium oxide (In{sub 2}O{sub 3}) nanorods, nanotowers and tin-doped (Sn:In = 1:100) indium oxide (ITO) nanorods have been fabricated by thermal evaporation. The morphology, microstructure and chemical composition of these three nanoproducts are characterized by FE-SEM, HRTEM and XPS. To further investigate the optoelectronic properties, the I–V curves and cathodoluminescence (CL) spectra are measured. The electrical resistivity of In{sub 2}O{sub 3} nanorods, nanotowers and ITO nanorods are 1.32 kΩ, 0.65 kΩ and 0.063 kΩ, respectively. CL spectra of these three nanoproducts clearly indicate that tin-doped (Sn:In = 1:100) indium oxide (ITO) nanorods cause a blue shift. No doubt ITO nanorods obtain the highest performance among these three nanoproducts, and this also means that Sn-doped In{sub 2}O{sub 3} nanostructures would be the best way to enhance the optoelectronic properties. Additionally, the growing mechanism and the optoelectronic properties of these three nanostructures are discussed. This study is beneficial to the applications of In{sub 2}O{sub 3} nanorods, nanotowers and ITO nanorods in optoelectronic nanodevices.

Indium 111 scintigraphy in the exploration of the erythropoietic marrow (relative to 42 observations)

International Nuclear Information System (INIS)

Guerin, G.C.R.

1976-01-01

The bone marrow is difficult to explore as a whole because of its wide non-uniform distribution, variable with the hematopoietic and supporting tissue sites. 111 indium-transferrine bone marrow scintigraphy is a new technique which partly overcomes these difficulties and gives an idea of the overall distribution and richness of the erythropoietic marrow, thus showing up the erythropoiesis sites at a given moment. The properties of indium as medullary tracer are bound up with the characteristics of its metabolism which, to some extent at least resembles that of iron. The two main features are: - its fixation on transferrine (or siderophiline); - its binding to reticulocytes. Moreover indium 111 fulfils the physico-chemical criteria necessary for scintigraphic practice (long half-life, emission detectable by conventional scintigraphs, moderate irradiation of the patient). The properties of this radioelement and the technical conditions of use are examined in turn, then scintigraphic data are compared with the results of traditional bone marrow investigations: medullary biopsy and blood cell counts with reticulocyte fraction. This comparison concerns 42 scintigraphs carried out on patients suffering from various hematological diseases, with prospects of serious development in common [fr

Ternary equilibria in bismuth--indium--lead alloys

International Nuclear Information System (INIS)

Liao, K.C.; Johnson, D.L.; Nelson, R.C.

1975-01-01

The liquidus surface is characterized by three binary equilibria. One binary extends from the Pb--Bi peritectic to the Pb--In peritectic. The other two extend from In--Bi eutectics, merge at 50 at. percent Bi and 30 at. percent Pb, and end at the Bi--Pb eutectic. Based on analysis of ternary liquidus contours and vertical sections, it is suggested that solidification for high lead and very high indium alloys occurs from two-phase equilibria. Solidification from all other alloys occurs from three-phase equilibria. Four-phase solidification does not occur in this system

Extraction chromatography of indium (III) on silica gel impregnated with high molecular weight carboxylic acid and its analytical applications

International Nuclear Information System (INIS)

Majumdar, P.S.; Ray, U.S.

1991-01-01

Indium(III) was separated by extraction chromatography with Versatic 10 as a stationary phase on a column of silica gel from acetic acid and sodium acetate solution (pH 4.5-6.0). The optimum condition for extraction was studied based on the critical study of the relevant factors as effects of pH, flow rate on extraction and elution. Role of stripping agents on the elution was studied. The separation of indium from a number of elements was carried out. Indium(III) was separated from Alsup(III), Gasup(III), Tlsup(III), Zrsup(IV) and trivalent lanthanides which interfere under the recommended extraction condition by exploiting the differences in their stripping behaviour. (author). 7 refs., 1 tab., 1 fig

Enhanced photo-catalytic activity of ordered mesoporous indium oxide nanocrystals in the conversion of CO2 into methanol.

Science.gov (United States)

Gondal, M A; Dastageer, M A; Oloore, L E; Baig, U; Rashid, S G

2017-07-03

Ordered mesoporous indium oxide nanocrystal (m-In 2 O 3 ) was synthesized by nanocasting technique, in which highly ordered mesoporous silca (SBA-15) was used as structural matrix. X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM) Brunauer-Emmett-Teller (BET) and Barrett-Joyner-Halanda (BJH) studies were carried out on m-In 2 O 3 and the results revealed that this material has a highly ordered mesoporous surface with reduced grain size, increased surface area and surface volume compared to the non porous indium oxide. The diffuse reluctance spectrum exhibited substantially improved light absorption efficiency in m-In 2 O 3 compared to normal indium oxide, however, no considerable change in the band gap energies of these materials was observed. When m-In 2 O 3 was used as a photo-catalyst in the photo-catalytic process of converting carbon dioxide (CO 2 ) into methanol under the pulsed laser radiation of 266-nm wavelengths, an enhanced photo-catalytic activity with the quantum efficiency of 4.5% and conversion efficiency of 46.3% were observed. It was found that the methanol production yield in this chemical process is as high as 485 µlg -1 h -1 after 150 min of irradiation, which is substantially higher than the yields reported in the literature. It is quite clear from the results that the introduction of mesoporosity in indium oxide, and the consequent enhancement of positive attributes required for a photo-catalyst, transformed photo-catalytically weak indium oxide into an effective photo-catalyst for the conversion of CO 2 into methanol.

Thermal transport properties of polycrystalline tin-doped indium oxide films

International Nuclear Information System (INIS)

Ashida, Toru; Miyamura, Amica; Oka, Nobuto; Sato, Yasushi; Shigesato, Yuzo; Yagi, Takashi; Taketoshi, Naoyuki; Baba, Tetsuya

2009-01-01

Thermal diffusivity of polycrystalline tin-doped indium oxide (ITO) films with a thickness of 200 nm has been characterized quantitatively by subnanosecond laser pulse irradiation and thermoreflectance measurement. ITO films sandwiched by molybdenum (Mo) films were prepared on a fused silica substrate by dc magnetron sputtering using an oxide ceramic ITO target (90 wt %In 2 O 3 and 10 wt %SnO 2 ). The resistivity and carrier density of the ITO films ranged from 2.9x10 -4 to 3.2x10 -3 Ω cm and from 1.9x10 20 to 1.2x10 21 cm -3 , respectively. The thermal diffusivity of the ITO films was (1.5-2.2)x10 -6 m 2 /s, depending on the electrical conductivity. The thermal conductivity carried by free electrons was estimated using the Wiedemann-Franz law. The phonon contribution to the heat transfer in ITO films with various resistivities was found to be almost constant (λ ph =3.95 W/m K), which was about twice that for amorphous indium zinc oxide films

A comparative study of the annealing behavior of Cu(In,Ga)(S,Se)2 based solar cells with an indium sulfide buffer layer, partly submitted to wet chemical treatments

International Nuclear Information System (INIS)

Hönes, C.; Hackenberg, J.; Zweigart, S.; Wachau, A.; Hergert, F.; Siebentritt, S.

2015-01-01

Indium sulfide thin films deposited via thermal evaporation from compound source material have been successfully utilized as a cadmium free buffer layer for Cu(In,Ga)Se 2 based solar cells. However, high efficiencies are only reached after an additional annealing step. In this work, the annealing behavior of Cu(In,Ga)(S,Se) 2 based indium sulfide buffered solar cells is compared to the annealing behavior of similar cells, which were submitted to wet chemical treatments partly containing cadmium ions. Upon annealing a significant improvement of the initial solar cell characteristics is observed for the untreated cell and is related to the increase of activation energy for the carrier recombination process and a decrease of the ideality factor within the one diode model. It is shown here that this improvement can also be achieved by wet treatments of the absorber prior to buffer layer deposition. Upon annealing these treated cells still gain in collection length but lose open circuit voltage, which is explained here within a model including a highly p-doped absorber surface layer and supported by simulations showing that a decrease in doping density of such a surface layer would lead to the observed effects

Annealing of wet treated Cu(In,Ga)(S,Se){sub 2} solar cells with an indium sulfide buffer

Energy Technology Data Exchange (ETDEWEB)

Hönes, C., E-mail: christian.hoenes.001@student.uni.lu; Siebentritt, S., E-mail: susanne.siebentritt@uni.lu

2015-05-01

Compound evaporated indium sulfide is one commonly utilized cadmium free buffer layer for Cu(In,Ga)(S,Se){sub 2} solar cells. However, cells with such a buffer layer usually need a post-deposition annealing step to reach the maximum short circuit current, fill factor and open circuit voltage. In this work wet chemical treatments, partly containing cadmium ions, are applied to commercially available absorber material prior to indium sulfide evaporation in order to enhance the initial solar cell parameters. Cells built on treated absorbers show maximum open circuit voltage directly after window layer deposition and a drop in open circuit voltage is observed upon annealing. All samples, however, show an increased collection length and higher fill factor after annealing. A one diode model fit to the current-voltage curves gives ideality factors of 1.7 before annealing which are reduced to values around 1.5 after annealing. Supporting calculations show that the changes upon annealing can be explained within a model including a highly p-doped absorber surface layer. During annealing the acceptor density at the absorber surface might be reduced thus leading to a larger space charge region and thereby increasing the collection length and fill factor while reducing the open circuit voltage. - Highlights: • Wet treatments raise initial voltage of In{sub 2}S{sub 3} buffered Cu(In,Ga)(S,Se){sub 2} solar cells. • Collection length increase after annealing of treated cells is observed. • Voltage decay is explained within a model including a highly p-doped surface layer. • Supporting simulations are in good agreement with the experiments.

Effect of indium doping on zinc oxide films prepared by chemical ...

Indian Academy of Sciences (India)

Administrator

confirmed by X-ray diffraction technique which leads to the introduction of defects in ZnO. Indium doping ... elements like Al, Ga and In can be used as n-type dopant. (Kato et al 2002) .... (α is the absorption coefficient and hν the photon energy).

Generic Top-Functionalization of Patterned Antifouling Zwitterionic Polymers on Indium Tin Oxide

NARCIS (Netherlands)

Li, Y.; Giesbers, M.; Zuilhof, H.

2012-01-01

This paper presents a novel surface engineering approach that combines photochemical grafting and surface-initiated atom transfer radical polymerization (SI-ATRP) to attach zwitterionic polymer brushes onto indium tin oxide (ITO) substrates. The photochemically grafted hydroxyl-terminated organic

Atomic layer epitaxy of hematite on indium tin oxide for application in solar energy conversion

Science.gov (United States)

Martinson, Alex B.; Riha, Shannon; Guo, Peijun; Emery, Jonathan D.

2016-07-12

A method to provide an article of manufacture of iron oxide on indium tin oxide for solar energy conversion. An atomic layer epitaxy method is used to deposit an uncommon bixbytite-phase iron (III) oxide (.beta.-Fe.sub.2O.sub.3) which is deposited at low temperatures to provide 99% phase pure .beta.-Fe.sub.2O.sub.3 thin films on indium tin oxide. Subsequent annealing produces pure .alpha.-Fe.sub.2O.sub.3 with well-defined epitaxy via a topotactic transition. These highly crystalline films in the ultra thin film limit enable high efficiency photoelectrochemical chemical water splitting.

Solvent effects on extraction of aluminum(III), gallium(III), and indium(III), with decanoic acid

International Nuclear Information System (INIS)

Yamada, Hiromichi; Hayashi, Hisao; Fujii, Yukio; Mizuta, Masateru

1986-01-01

Extraction of aluminum(III) and indium(III) with decanoic acid in 1-octanol was carried out at 25 deg C and at an aqueous ionic strength of 0.1 mol dm -3 (NaClO 4 ). Monomeric and tetrameric aluminum(III) decanoates and monomeric indium(III) decanoate are responsible for the extraction. From a comparison of the present results with those obtained from the previous works, the polymerization of the extracted species was found to be more extensive in benzene than in 1-octanol, and the metal decanoates were highly polymerized in the following order in both solvents: Al > Ga > In. (author)

Indium-111 autologous tagged leukocytes in the diagnosis of intraperitoneal sepsis

International Nuclear Information System (INIS)

Ascher, N.L.; Ahrenholz, D.H.; Simmons, R.L.; Weiblen, B.; Gomez, L.; Forstrom, L.A.; Frick, M.P.; Henke, C.; McCullough, J.

1979-01-01

The results of a new test using indium oxine in the diagnosis of postoperative infection are reported. Indium-111 was used to label autologous polymorphonuclear leukocytes, which when reinjected migrate to sites of infection and inflammation. Standard scintigraphy localizes the labeled inflammatory cells at these sites. Sixty-six scans were performed in 43 surgical patients. Thirty-seven scans were categorized as true-positive; 19 scans were categorized as true-negative. Therefore, the accuracy rate was 85%. Two scans (3%) in one patient represented false-positive results. Two scans (3%) were positive for inflammation but there was no infection present; this group was denoted as equivocal. Six scans (9%) were false-negative; false-negative scans are more likely in old lesions with poor blood supply and in areas that overlap regions of normal uptake. The noninvasive nature of the test, high accuracy rate, and ease of administration make it a potentially useful tool in the diagnosis of postoperative infection

The use of indium-111 labeled platelet scanning for the detection of asymptomatic deep venous thrombosis in a high risk population

International Nuclear Information System (INIS)

Siegel, R.S.; Rae, J.L.; Ryan, N.L.; Edwards, C.; Fortune, W.P.; Lewis, R.J.; Reba, R.C.

1989-01-01

Five hundred indium-111 labeled platelet imaging studies (387 donor and 113 autologous) were performed postoperatively in 473 patients who had undergone total hip replacement, total knee replacement, or internal fixation of a hip fracture to detect occult deep venous thrombosis. All patients had been anticoagulated prophylactically with aspirin, warfarin sodium (Coumadin), or dextran. Thirty-four possible cases of proximal deep venous thrombosis were identified in 28 asymptomatic patients. To verify the scan results, 31 venograms were performed in 25 patients (three refused). In 21 of 31 cases, totally occlusive thrombi were detected; in 5 cases, partially occlusive thrombi were detected; in 5 cases, no thrombus was seen. No patient who had a negative scan nor any patient who had a verified positive scan (and received appropriate heparin therapy) subsequently developed symptoms or signs of pulmonary embolism. One hundred forty-one indium study patients also underwent Doppler ultrasonography/impedance plethysmography (Doppler/IPG) as a comparative non-invasive technique. In 137 cases, the results of the indium study and Doppler/IPG studies were congruent. The indium study had no false negative results that were detected by Doppler/IPG. No patient had any clinically evident toxicity. These results suggest that indium-111 labeled platelet scanning is a safe, noninvasive means for identifying DVT in high risk patients

Highly Sensitive ZnO(Ga, In for Sub-ppm Level NO2 Detection: Effect of Indium Content

Directory of Open Access Journals (Sweden)

Natalia Vorobyeva

2017-06-01

Full Text Available Nanocrystalline ZnO, ZnO(Ga, and ZnO(Ga, In samples with different indium contents were prepared by wet-chemical method and characterized in detail by ICP-MS and XRD methods. Gas sensing properties toward NO2 were studied at 150–450 °C by DC conductance measurements. The optimal temperature for gas sensing experiments was determined. The dependence of the ZnO(Ga, In sensor signal to NO2 at 250 °C correlates with the change of conductivity of the samples. The introduction of indium into the system leads to an increase in the values of the sensor signal in the temperature range T < 250 °C. The investigation of the local sample conductivity by scanning spreading resistance microscopy demonstrates that, at high indium content, the sensor properties are determined by the In–Ga–Zn–O layer that forms on the ZnO surface.

Improved superconducting properties of La{sub 3}Co{sub 4}Sn{sub 13} with indium substitution

Energy Technology Data Exchange (ETDEWEB)

Neha, P.; Srivastava, P. [School of Physical Sciences, Jawaharlal Nehru University, New Delhi 110067 (India); Jha, R. [School of Physical Sciences, Jawaharlal Nehru University, New Delhi 110067 (India); National Physical Laboratory, New Delhi 110012 (India); Shruti [School of Physical Sciences, Jawaharlal Nehru University, New Delhi 110067 (India); Awana, V.P.S. [National Physical Laboratory, New Delhi 110012 (India); Patnaik, S., E-mail: spatnaik@mail.jnu.ac.in [School of Physical Sciences, Jawaharlal Nehru University, New Delhi 110067 (India)

2016-04-25

We report two fold increase in superconducting transition temperature of La{sub 3}Co{sub 4}Sn{sub 13} by substituting indium at the tin site. The transition temperature of this skutterudite related compound is observed to increase from 2.5 K to 5.1 K for 10% indium substituted sample. The band structure and density of states calculations also indicate such a possibility. The compounds exhibit type-II superconductivity and the values of lower critical field (H{sub c1}), upper critical field (H{sub c2}), Ginzburg–Landau coherence length (ξ), penetration depth (λ) and GL parameter (κ) are estimated to be 0.0028 T, 0.68 T, 21.6 nm, 33.2 nm and 1.53 respectively for La{sub 3}Co{sub 4}Sn{sub 11.7}In{sub 1.3}. Hydrostatic external pressure leads to decrease in transition temperature and the calculated pressure coefficient is −0.311 K/GPa. Flux pinning and vortex activation energies also improved with indium addition. Only positive frequencies are observed in phonon dispersion curve that relate to the absence of charge density wave or structural instability in the normal state. - Highlights: • Superconducting transition temperature of La{sub 3}Co{sub 4}Sn{sub 13} increases two fold by indium substitution. • Band structure and all basic superconducting parameters (e.g,. H{sub c1}, H{sub c2}, ξ,λ and κ are ascertained. • Dependence of superconducting properties under external pressure is studied.

Diffuse pulmonary uptake of indium-111 chloride in idiopathic myelofibrosis

International Nuclear Information System (INIS)

Vieras, F.; Boyd, C.M.; Mora, P.A.

1979-01-01

Unusual indium-111 accumulation and extramedullary hematopoiesis in the lungs of a patient with idiopathic myelofibrosis are described. The bone marrow scan taken 24 h after intravenous injection of 111 InCl 3 faithfully depicted the abnormal distribution of marrow elements as assessed histologically at autopsy, thereby supporting the usefulness of 111 InCl 3 for marrow imaging

A comparison of gallium-67 citrate scintigraphy and indium-111 labelled leukocyte imaging for the diagnosis of prosthetic joint infection. Preliminary results

International Nuclear Information System (INIS)

McKillop, J.H.; Cuthbert, G.F.; Gray, H.W.; McKay, Iain; Sturrock, R.D.

1982-01-01

Preliminary experience in comparing Gallium-67 imaging in patients with a painful prosthetic joint to the findings on Indium-111 labelled leukocyte imaging is reported. In the small series of patients so far studied, no clear advantage has emerged for either Gallium-67 or Indium-111 leukocyte imaging in terms of sensitivity or specificity for joint prosthesis infection. Should a larger group confirm the preliminary findings, Gallium-67 imaging may be preferable to Indium-111 leukocyte imaging in the patient with the painful joint prosthesis, in view of the greater simplicity of the former technique

Detection of a prosthetic aortic valvular abscess with indium-111-labeled leukocytes

Energy Technology Data Exchange (ETDEWEB)

Oates, E.; Sarno, R.C.

1988-10-01

An unsuspected annular abscess at the base of a prosthetic aortic valve in a patient with endocarditis was identified by indium-111-labeled leukocyte scintigraphy alone. This highly sensitive and specific technique expediently demonstrated the surgically proven inflammatory focus.

Detection of a prosthetic aortic valvular abscess with indium-111-labeled leukocytes

International Nuclear Information System (INIS)

Oates, E.; Sarno, R.C.

1988-01-01

An unsuspected annular abscess at the base of a prosthetic aortic valve in a patient with endocarditis was identified by indium-111-labeled leukocyte scintigraphy alone. This highly sensitive and specific technique expediently demonstrated the surgically proven inflammatory focus

Sol–gel synthesis of nanostructured indium tin oxide with controlled morphology and porosity

Energy Technology Data Exchange (ETDEWEB)

Kőrösi, László, E-mail: ltkorosi@gmail.com [Department of Biotechnology, Nanophage Therapy Center, Enviroinvest Corporation, Kertváros u. 2, H-7632 Pécs (Hungary); Scarpellini, Alice [Department of Nanochemistry, Istituto Italiano di Tecnologia, via Morego 30, 16163 Genova (Italy); Petrik, Péter [Institute for Technical Physics and Materials Science, Konkoly-Thege út 29-33, H-1121 Budapest (Hungary); Papp, Szilvia [Department of Biotechnology, Nanophage Therapy Center, Enviroinvest Corporation, Kertváros u. 2, H-7632 Pécs (Hungary); Dékány, Imre [MTA-SZTE Supramolecular and Nanostructured Materials Research Group, University of Szeged, Dóm tér 8, H-6720 Szeged (Hungary)

2014-11-30

Graphical abstract: - Highlights: • Nanocrystalline ITO thin films and powders were prepared by a sol–gel method. • The nature of the compounds used for hydrolysis plays a key role in the morphology. • Hydrolysis of In{sup 3+}/Sn{sup 4+} with EA led to a rod-like morphology. • Monodisperse spherical ITO nanoparticles were obtained on the use of AC. • ITO{sub E}A was highly porous, while ITO{sub A}C contained densely packed nanocrystals. - Abstract: Nanostructured indium tin oxide (ITO) powders and thin films differing in morphology and porosity were prepared by a sol–gel method. In{sup 3+} and Sn{sup 4+} were hydrolyzed in aqueous medium through the use of ethanolamine (EA) or sodium acetate (AC). X-ray diffraction measurements demonstrated that both EA and AC furnished indium tin hydroxide, which became nanocrystalline after aging for one day. The indium tin hydroxide samples calcined at 550 °C afforded ITO with a cubic crystal structure, but the morphology differed significantly, depending on the agent used for hydrolysis. Electron microscopy revealed the formation of round monodisperse nanoparticles when AC was used, whereas the application of EA led to rod-like ITO nanoparticles. Both types of nanoparticles were suitable for the preparation of transparent and conductive ITO thin films. The influence of the morphology and porosity on the optical properties is discussed.

Optical properties of ITO films obtained by high-frequency magnetron sputtering with accompanying ion treatment

Energy Technology Data Exchange (ETDEWEB)

Krylov, P. N., E-mail: ftt@uni.udm.ru; Zakirova, R. M.; Fedotova, I. V. [Udmurt State University (Russian Federation)

2013-10-15

A variation in the properties of indium-tin-oxide (ITO) films obtained by the method of reactive magnetron sputtering with simultaneous ion treatment is reported. The ITO films feature the following parameters in the optical range of 450-1100 nm: a transmission coefficient of 80%, band gap of 3.50-3.60 eV, and a refractive index of 1.97-2.06. All characteristics of the films depend on the ion-treatment current. The latter, during the course of deposition, reduces the resistivity of the ITO films with the smallest value of the resistivity being equal to 2 Multiplication-Sign 10{sup -3} {Omega} cm. The degradation of films with a high resistivity when kept in air is observed.

Studies on the electrical properties of reactive DC magnetron-sputtered indium-doped silver oxide thin films: The role of oxygen

Energy Technology Data Exchange (ETDEWEB)

Subrahmanyam, A [Semiconductor Physics Laboratory, Department of Physics, Indian Institute of Technology Madras, Chennai 600036 (India); Barik, Ullash Kumar [Semiconductor Physics Laboratory, Department of Physics, Indian Institute of Technology Madras, Chennai 600036 (India)

2007-03-15

Indium ({approx}10 at.%)-doped silver oxide (AIO) thin films have been prepared on glass substrates at room temperature (300 K) by reactive DC magnetron sputtering technique using an alloy target made of pure (99.99%) silver and indium (90:10 at.%) metals. The oxygen flow rates have been varied in the range 0.00-3.44 sccm during sputtering. The X-ray diffraction data on these indium-doped silver oxide films show polycrystalline nature. With increasing oxygen flow rate, the carrier concentration, the Hall mobility and the electron mean free path decrease. These films show a very low positive temperature coefficient of resistivity {approx}3.40x10{sup -8} ohm-cm/K. The work function values for these films (measured by Kelvin probe technique) are in the range 4.81-5.07 eV. The high electrical resistivity indicate that the films are in the island state (size effects). Calculations of the partial ionic charge (by Sanderson's theory) show that indium doping in silver oxide thin films enhance the ionicity.

Studies on the electrical properties of reactive DC magnetron-sputtered indium-doped silver oxide thin films: The role of oxygen

International Nuclear Information System (INIS)

Subrahmanyam, A.; Barik, Ullash Kumar

2007-01-01

Indium (∼10 at.%)-doped silver oxide (AIO) thin films have been prepared on glass substrates at room temperature (300 K) by reactive DC magnetron sputtering technique using an alloy target made of pure (99.99%) silver and indium (90:10 at.%) metals. The oxygen flow rates have been varied in the range 0.00-3.44 sccm during sputtering. The X-ray diffraction data on these indium-doped silver oxide films show polycrystalline nature. With increasing oxygen flow rate, the carrier concentration, the Hall mobility and the electron mean free path decrease. These films show a very low positive temperature coefficient of resistivity ∼3.40x10 -8 ohm-cm/K. The work function values for these films (measured by Kelvin probe technique) are in the range 4.81-5.07 eV. The high electrical resistivity indicate that the films are in the island state (size effects). Calculations of the partial ionic charge (by Sanderson's theory) show that indium doping in silver oxide thin films enhance the ionicity

Determination of the indium content and layer thicknesses in InGaN/GaN quantum wells by x-ray scattering

International Nuclear Information System (INIS)

Vickers, M.E.; Kappers, M.J.; Smeeton, T.M.; Thrush, E.J.; Barnard, J.S.; Humphreys, C.J.

2003-01-01

We have determined the indium content and the layer thicknesses in an InGaN epilayer and InGaN/GaN quantum well structures by high-resolution x-ray diffraction (XRD) using the (002) reflection. The thickness of the total repeat (an InGaN well plus a GaN barrier) in the superlattice is easily determined from the spacing between the satellite peaks in an omega/2theta scan. Measurement of the individual thickness of InGaN and GaN layers and the indium content is less straightforward, since for multilayer structures the peak positions are influenced by both the indium content and the thickness ratio of the GaN to the InGaN layer. Thus, several different models may give reasonable fits to data collected over a limited range (about 1 deg. omega/2theta either side of the (002)) showing only lower-order (-3 to +3) satellite peaks. Whenever possible, we have collected data over a wide range (about 4 deg. omega/2theta) and determined the thickness ratio by examination of the relative intensities of weak higher-order satellite peaks (-7 to +5). An alternative but less sensitive method is to use relative intensities from x-ray reflectivity measurements to give the thickness ratio. Once the thickness of both the InGaN and GaN layers has been established, the InGaN composition can be determined from the peak positions. If the quality of the samples is poor, because of inhomogeneities or wide diffuse interfaces, there are insufficient data to characterize the structures. There is good agreement between the composition of the epilayer as determined by XRD and secondary ion mass spectroscopy and good agreement between x-ray and electron microscopy results for the quantum well structures. We find no variation from Vegard's rule for In contents less than 0.20. This article shows that structural parameters of high-quality InGaN/GaN superlattices with 10 and 5 repeats can be determined reliably by x-ray techniques: The InGaN and GaN thicknesses to ±1 Aa and the In content to ±0.01

Composition and structure of ion-bombardment-induced growth cones on InP

International Nuclear Information System (INIS)

Malherbe, J.B.; Lakner, H.; Gries, W.H.

1991-01-01

The previously reported effect of low-energy (several keV) ion bombardment on the surface topography of InP was investigated by scanning transmission electron microscopy. Convergent beam electron diffraction patterns of the surface growth 'cones' induced by argon ion bombardment of (100) InP between 7 and 10 keV proved the cones to consist of crystalline InP (and not metallic indium, as has sometimes been claimed). The investigation showed that the irradiated surface region is not rendered completely amorphous but that it recrystallizes from the crystalline/amorphous interface in a columnar growth pattern, often terminating in growth cones protruding above the surface. Weak beam investigations revealed that the overwhelming majority of the cones have the orientation of the substrate. These phenomena were observed at all dose densities from 7 x 10 15 to 2 x 10 17 cm -2 . (author)

SU-E-I-14: Comparison of Iodine-Labeled and Indium-Labeled Antibody Biodistributions

Energy Technology Data Exchange (ETDEWEB)

Williams, L [Retired from City of Hope Medical Center, Arcadia, CA (United States)

2014-06-01

Purpose: It is often assumed that animal biodistributions of novel proteins are not dependent upon the radiolabel used in their determination. In units of percent injected dose per gram of tissue (%ID/g), organ uptake results (u) may be obtained using either iodine or metal as radioactive labels. Iodination is preferred as it is a one-step process whereas metal labeling requires two chemical procedures and therefore more protein material. It is important to test whether the radioactive tag leads to variation in the uptake value. Methods: Uptakes of 3antibodies to Carcinoembryonic Antigen (CEA) were evaluated in a nude mouse model bearing 150 to 300 mg LS174T human colon cancer xenografts. Antibodies included diabody (56 kDa), minibody (80kDa) and intact M5A (150 kDa) anti-CEA cognates. Both radioiodine and indium-111 labels were used with uptakes evaluated at 7 time(t) points out to 96 h. Ratios (R) of u(iodine-label)/u(indium-label) were determined for liver, spleen, kidneys, lung and tumor. Results: Hepatic loss was rapid for diabody and minibody; by 24 h their R values were only 2%; i.e., uptake of iodine was 2% of that of indium for these 2 antibodies. By contrast, R for the intact cognate was 50% at that time point. Splenic results were similar. Tumor uptake ratios did not depend upon the antibody type and were 50% at 24 h. Conclusions: Relatively rapid loss of iodine relative to indium in liver and spleen was observed in lower mass antibodies. Tumor ratios were larger and independent of antibody type. Aside from tumor, the R ratio of uptakes depended on the antibody type. R values decreased monotonically with time in all tissues and for all cognates. Using this ratio, one can possibly correct iodine-based u (t) results so that they resemble radiometal-derived biodistributions.

Thermodynamic Considerations for a Pyrometallurgical Extraction of Indium and Silver from a Jarosite Residue

Directory of Open Access Journals (Sweden)

Stefan Steinlechner

2018-05-01

Full Text Available Indium and silver are technologically important, critical metals, and in the majority of cases, they are extracted as a by-product of another carrier metal. The importance of indium has seen recent growth, and for technological reasons, these metals can be found in industrial residues from primary zinc production, such as the iron precipitate—jarosite. To secure the supply of such metals in Europe, and with the idea of a circular economy and the sustainable use of raw materials, the recycling of such industrial residues is coming into focus. Due to the low value of jarosite, the focus must lie simultaneously on the recovery of valuable metals and the production of high-quality products in order to pursue an economical process. The objective of this article is to give the fundamentals for the development of a successful process to extract the minor elements from roasted jarosite. As such, we use thermodynamic calculations to show the behavior of indium and silver, leading to a recommendation for the required conditions for a successful extraction process. In summary, the formation of chlorine compounds shows high potential to meet the challenge of simultaneously recovering these metals together with zinc at the lowest possible energy input.

Indium--tin oxide films radio frequency sputtered from specially formulated high density indium--tin oxide targets

International Nuclear Information System (INIS)

Kulkarni, S.; Bayard, M.

1991-01-01

High density ITO (indium--tin oxide) targets doped with Al 2 O 3 and SiO 2 manufactured in the Tektronix Ceramics Division have been used to rf sputter ITO films of various thicknesses on borosilicate glass substrates. Sputtering in an oxygen--argon gas mixture and annealing in forming gas, resulted in ITO films exhibiting 90% transmission at 550 nm and a sheet resistance of 15 Ω/sq for a thickness of 1100 A. Sputtering in an oxygen--argon gas mixture and annealing in air increased sheet resistance without a large effect on the transmission. Films sputtered in argon gas alone were transparent in the visible and the sheet resistance was found to be 100--180 Ω/sq for the same thickness, without annealing

Detection of heavy metal ions in contaminated water by surface plasmon resonance based optical fibre sensor using conducting polymer and chitosan.

Science.gov (United States)

Verma, Roli; Gupta, Banshi D

2015-01-01

Optical fibre surface plasmon resonance (SPR) based sensor for the detection of heavy metal ions in the drinking water is designed. Silver (Ag) metal and indium tin oxide (ITO) are used for the fabrication of the SPR probe which is further modified with the coating of pyrrole and chitosan composite. The sensor works on the wavelength interrogation technique and is capable of detecting trace amounts of Cd(2+), Pb(2+), and Hg(2+) heavy metal ions in contaminated water. Four types of sensing probes are fabricated and characterised for heavy metal ions out of these pyrrole/chitosan/ITO/Ag coated probe is found to be highly sensitive among all other probes. Further, the cadmium ions bind strongly to the sensing surface than other ions and due to this the sensor is highly sensitive for Cd(2+) ions. The sensor's performance is best for the low concentrations of heavy metal ions and its sensitivity decreases with the increasing concentration of heavy metal ions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Highly luminescent, high-indium-content InGaN film with uniform composition and full misfit-strain relaxation

Science.gov (United States)

Fischer, A. M.; Wei, Y. O.; Ponce, F. A.; Moseley, M.; Gunning, B.; Doolittle, W. A.

2013-09-01

We have studied the properties of thick InxGa1-xN films, with indium content ranging from x ˜ 0.22 to 0.67, grown by metal-modulated epitaxy. While the low indium-content films exhibit high density of stacking faults and dislocations, a significant improvement in the crystalline quality and optical properties has been observed starting at x ˜ 0.6. Surprisingly, the InxGa1-xN film with x ˜ 0.67 exhibits high luminescence intensity, low defect density, and uniform full lattice-mismatch strain relaxation. The efficient strain relaxation is shown to be due to a critical thickness close to the monolayer range. These films were grown at low temperatures (˜400 °C) to facilitate indium incorporation and with precursor modulation to enhance surface morphology and metal adlayer diffusion. These findings should contribute to the development of growth techniques for nitride semiconductors under high lattice misfit conditions.

The energy of hydration and solvation of indium salts in the acetylacetone-InCl3-water system

International Nuclear Information System (INIS)

Kulawik, I.; Baumgartner, T.

1978-01-01

On the base of the previous papers concerning the investigations in the extraction systems the experiments were performed for the determination of thermodynamical distribution coefficient of indium salts between two phases in the system: acetylacetone-InCl 3 -water and the energy of hydration and solvation of that system. The results of the surface and interfacial potentials measurements of the system were presented as a function of the InCl 3 concentration in the system before the extraction. The extraction coefficients of indium as a function of concentration of InCl 3 in this system were determined. The method of the visible absorption spectra was used to the determination of concentration of indium in both phases after the extraction. The relation between the percentage of the extraction and the extraction coefficient was determined. The investigations were performed in the system containing 0.1 M HCl and 0.001 M HCl in the aqueous phase. The results of experiments are tabulated and graphically presented in figures. (author)

Substitution effect of pentavalent bismuth ions on the electronic structure and physicochemical properties of perovskite-structured Ba(In0.5Ta0.5-xBix)O3 semiconductors

International Nuclear Information System (INIS)

Kim, Tae Woo; Hur, Su Gil; Hwang, Seong-Ju; Park, Hyunwoong; Park, Yiseul; Choi, Wonyong; Choy, Jin-Ho

2007-01-01

We have investigated the substitution effect of pentavalent bismuth ions on the electronic structure and physicochemical properties of barium indium tantalate. X-ray diffraction, X-ray absorption spectroscopic, and energy dispersive spectroscopic microprobe analyses reveal that, under oxygen atmosphere of 1 atm, pentavalent Bi ions are successfully stabilized in the octahedral site of the perovskite tantalate lattice. According to diffuse reflectance UV-vis spectroscopic analysis, the Bi substitution gives rise to the significant narrowing of band gap of barium indium tantalate even at a low Bi content of ∼5%, underscoring a high efficiency of Bi substitution in the band gap engineering. Such an effective narrowing of the band gap upon the Bi substitution would be attributable to the lowering of conduction band position due to the high electronegativity of Bi V substituent. As a result of band gap engineering, the Ba(In 0.5 Ta 0.5-x Bi x )O 3 compounds with x ≥ 0.03 can generate photocurrents under visible light irradiation (λ > 420 nm). Based on the present experimental findings, it becomes clear that the substitution of highly electronegative p-block element like Bi V ion can provide a very powerful tool for tailoring the electronic structure and physicochemical properties of wide band gap semiconductors

Printed indium gallium zinc oxide transistors. Self-assembled nanodielectric effects on low-temperature combustion growth and carrier mobility.

Science.gov (United States)

Everaerts, Ken; Zeng, Li; Hennek, Jonathan W; Camacho, Diana I; Jariwala, Deep; Bedzyk, Michael J; Hersam, Mark C; Marks, Tobin J

2013-11-27

Solution-processed amorphous oxide semiconductors (AOSs) are emerging as important electronic materials for displays and transparent electronics. We report here on the fabrication, microstructure, and performance characteristics of inkjet-printed, low-temperature combustion-processed, amorphous indium gallium zinc oxide (a-IGZO) thin-film transistors (TFTs) grown on solution-processed hafnia self-assembled nanodielectrics (Hf-SANDs). TFT performance for devices processed below 300 °C includes >4× enhancement in electron mobility (μFE) on Hf-SAND versus SiO2 or ALD-HfO2 gate dielectrics, while other metrics such as subthreshold swing (SS), current on:off ratio (ION:IOFF), threshold voltage (Vth), and gate leakage current (Ig) are unchanged or enhanced. Thus, low voltage IGZO/SAND TFT operation (IGZO combustion processing leaves the underlying Hf-SAND microstructure and capacitance intact. This work establishes the compatibility and advantages of all-solution, low-temperature fabrication of inkjet-printed, combustion-derived high-mobility IGZO TFTs integrated with self-assembled hybrid organic-inorganic nanodielectrics.

Measurement of the indium segregation in InGaN based LEDs with single atom sensitivity

International Nuclear Information System (INIS)

Jinschek, Joerg; Kisielowski, Christian; Van Dyck, Dirk; Geuens, Philippe

2003-01-01

In light emitting diodes (LED) consisting of GaN/InGaN/GaN quantum wells (QWs), the exact indium distribution inside the wells of the active region affects the performance of devices. Indium segregation can take place forming small InGaN clusters of locally varying composition. In the past, we used a local strain analysis from single HRTEM lattice images to determine the In composition inside the InGaN QWs with a resolution of 0.5 nm x 0.3 nm. Truly atomic resolution can be pursued by exploitation of intensity dependencies on the atomic number (Z) of the electron exit-wave (EW). In microscopes with sufficient sensitivity, local variations of amplitude and phase are found to be discrete with sample thickness, which allows for counting the number of atoms in each individual column of ∼0.08 nm diameter. In QW s of ∼17 percent of average indium concentration it is possible to discriminate between pure Ga columns and columns containing 1, 2, 3, or more In atoms because phase changes are discrete and element specific. The preparation of samples with atomically flat surfaces is a limiting factor for the application of the procedure

Concentration dependence of surface properties and molar volume of multicomponent system indium-tin-lead-bismuth

Energy Technology Data Exchange (ETDEWEB)

Dadashev, R; Kutuev, R [Complex Science Research Institute of the Science Academy of the Chechen Republic, 21 Staropromisl. shosse, Grozny 364096 (Russian Federation); Elimkhanov, D [Science Academy of the Chechen Republic (Russian Federation)], E-mail: edzhabrail@mail.ru

2008-02-15

The results of an experimental research of surface properties of the four-component system indium-tin-lead-bismuth are presented. The researches under discussion were carried out in a combined device in which the surface tension ({sigma}) is measured by the method of maximum pressure in a drop, and density ({rho}) is measured by advanced aerometry. Measurement errors are 0.7 % for surface tension measurement, and 0.2 % for density measurement. The study of the concentration dependence of {sigma} in this system has revealed the influence of the third and fourth components upon the characteristics of surface tension isotherms of the binary system indium-tin. It was found out that with an increase in the content of the third and fourth components the depth of the minimum on the surface tension isotherms of the indium-tin system {sigma} decreases. On the basis of the concentration dependence of the phenomenon of concentration bufferity is revealed. It is shown that despite the complex character, isotherms of {sigma} on beam sections of a multicomponent system do not contain qualitatively new features in comparison with the isotherms of these properties in lateral binary systems.

Influence of Fe{sup 3+} substitution on the dielectric and ferroelectric characteristics of Lead Indium Niobate

Energy Technology Data Exchange (ETDEWEB)

Divya, A.S.; Kumar, V., E-mail: vkumar10@yahoo.com

2015-07-15

Highlights: • Prepared phase-pure Fe{sup 3+}-substituted Lead Indium Niobate, Pb[(In{sub 0.50−x}Fe{sub x})Nb{sub 0.50}]O{sub 3} by sol–gel method. • Spontaneous Relaxor (R) → Ferroelectric (FE) transition observed for the composition with x = 0.20. • Local structural rearrangement responsible for R → FE transition has been confirmed by Raman spectroscopy. - Abstract: Lead Indium Niobate, Pb(In{sub 0.50}Nb{sub 0.50})O{sub 3} (PIN) is a complex perovskite that exhibits Relaxor (R) characteristics. In this study, we report the synthesis of phase-pure compositions in the system Pb[(In{sub 0.50−x}Fe{sub x})Nb{sub 0.50}]O{sub 3} by sol–gel method and discuss the influence of isovalent substitution of Indium by Iron on the dielectric and ferroelectric characteristics. Spontaneous transition to the Ferroelectric (FE) phase has been observed for the composition having x = 0.20. Local structural rearrangements responsible for R → FE transition have also been studied by Raman spectroscopy and are discussed in detail.

Technological process and optimum design of organic materials vacuum pyrolysis and indium chlorinated separation from waste liquid crystal display panels

Energy Technology Data Exchange (ETDEWEB)

Ma, En; Xu, Zhenming, E-mail: zmxu@sjtu.edu.cn

2013-12-15

Highlights: • The vacuum pyrolysis–vacuum chlorinated separation system was proposed to recover the waste LCD panel. • The system can recycle the whole waste LCD panels efficiently without negative effects to environment. • The 82.03% of the organic materials was reclaimed. All pyrolysis products can be utilized by a reasonable way. • The separation of indium was optimized by the central composite design (CCD) under response surface methodology (RSM). • The recovery ratio of indium was further increased to 99.97%. -- Abstract: In this study, a technology process including vacuum pyrolysis and vacuum chlorinated separation was proposed to convert waste liquid crystal display (LCD) panels into useful resources using self-design apparatuses. The suitable pyrolysis temperature and pressure are determined as 300 °C and 50 Pa at first. The organic parts of the panels were converted to oil (79.10 wt%) and gas (2.93 wt%). Then the technology of separating indium was optimized by central composite design (CCD) under response surface methodology (RSM). The results indicated the indium recovery ratio was 99.97% when the particle size is less than 0.16 mm, the weight percentage of NH{sub 4}Cl to glass powder is 50 wt% and temperature is 450 °C. The research results show that the organic materials, indium and glass of LCD panel can be recovered during the recovery process efficiently and eco-friendly.

Sputtered gold-coated ITO nanowires by alternating depositions from Indium and ITO targets for application in surface-enhanced Raman scattering

Science.gov (United States)

Setti, Grazielle O.; Mamián-López, Mónica B.; Pessoa, Priscila R.; Poppi, Ronei J.; Joanni, Ednan; Jesus, Dosil P.

2015-08-01

Indium Tin oxide (ITO) nanowires were deposited by RF sputtering over oxidized silicon using ITO and Indium targets. The nanowires grew on the substrate with a catalyst layer of Indium by the vapor-liquid-solid (VLS) mechanism. Modifications in the deposition conditions affected the morphology and dimensions of the nanowires. The samples, after being covered with gold, were evaluated as surface-enhanced Raman scattering (SERS) substrates for detection of dye solutions and very good intensifications of the Raman signal were obtained. The SERS performance of the samples was also compared to that of a commercial SERS substrate and the results achieved were similar. To the best of our knowledge, this is the first time ITO nanowires were grown by the sputtering technique using oxide and metal targets.

Selective growth of gold onto copper indium sulfide selenide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Witt, Elena; Parisi, Juergen; Kolny-Olesiak, Joanna [Oldenburg Univ. (Germany). Inst. of Physics, Energy and Semiconductor Research

2013-05-15

Hybrid nanostructures are interesting materials for numerous applications in chemistry, physics, and biology, due to their novel properties and multiple functionalities. Here, we present a synthesis of metal-semiconductor hybrid nanostructures composed of nontoxic I-III-VI semiconductor nanoparticles and gold. Copper indium sulfide selenide (CuInSSe) nanocrystals with zinc blende structure and trigonal pyramidal shape, capped with dodecanethiol, serve as an original semiconductor part of a new hybrid nanostructure. Metallic gold nanocrystals selectively grow onto vertexes of these CuInSSe pyramids. The hybrid nanostructures were studied by transmission electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and UV-Vis-absorption spectroscopy, which allowed us conclusions about their growth mechanism. Hybrid nanocrystals are generated by replacement of a sacrificial domain in the CuInSSe part. At the same time, small selenium nanocrystals form that stay attached to the remaining CuInSSe/Au particles. Additionally, we compare the synthesis and properties of CuInSSe-based hybrid nanostructures with those of copper indium disulfide (CuInS{sub 2}). CuInS{sub 2}/Au nanostructures grow by a different mechanism (surface growth) and do not show any selectivity. (orig.)

Formation of inorganic nanocomposites by filling TiO{sub 2} nanopores with indium and antimony sulfide precursor aerosols

Energy Technology Data Exchange (ETDEWEB)

Juma, Albert, E-mail: jumalberto@yahoo.com [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Azarpira, Anahita [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Fischer, Ch.-H. [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Free University Berlin, Institute of Chemistry and Biochemistry, Fabeckstr. 34-36, 14195 Berlin (Germany); Wendler, Elke [Friedrich-Schiller-Universität Jena, Institut für Festkörperphysik, Max-Wien-Platz 1, 07743 Jena (Germany); Dittrich, Thomas [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner-Platz 1, 14109 Berlin (Germany)

2014-09-01

Nanocomposites of nanoporous-TiO{sub 2}/In{sub 2}S{sub 3} and np-TiO{sub 2}/Sb{sub 2}S{sub 3} were formed by deposition of In{sub 2}S{sub 3} or Sb{sub 2}S{sub 3} using spray ion layer gas reaction technique from their precursor solutions onto nanoporous TiO{sub 2} substrates at temperatures of 150, 175 and 200 °C. The least penetration of the precursor into np-TiO{sub 2} was achieved for np-TiO{sub 2}/In{sub 2}S{sub 3} nanocomposites from indium acetylacetonate salt. The deepest penetration was obtained for both np-TiO{sub 2}/In{sub 2}S{sub 3}(Cl) and np-TiO{sub 2}/Sb{sub 2}S{sub 3} nanocomposites with effective diffusion coefficients of 3.3 × 10{sup −3} cm{sup 2}/s and 3.2 × 10{sup −3} cm{sup 2}/s, respectively. The transport of the precursors in np-TiO{sub 2} and the formation of different nanocomposites were described the regime of the Knudsen diffusion model. - Highlights: • Deposition of metal sulfides by ion layer gas reaction technique • Penetration and diffusion depend on precursor characteristics. • Pore transport described by Knudsen diffusion model • InCl{sub 3} precursor penetrates more than In(acac){sub 3}.

Electrothermal atomization laser-excited atomic fluorescence spectroscopy for the determination of indium

International Nuclear Information System (INIS)

Aucelio, R.Q.; Smith, B.W.; Winefordner, J.D.

1998-01-01

A dye laser pumped by a high-repetition-rate copper vapor laser was used as the excitation source to determine indium at parts-per-trillion level by electrothermal atomization laser-excited atomic fluorescence spectrometry (ETA-LEAFS). A comparison was made between wall atomization, in pyrolytic and nonpyrolytic graphite tubes, and platform atomization. The influence of several chemical modifiers either in solution or precoated in the graphite tube was evaluated. The influence of several acids and NaOH in the analyte solution was also studied. Optimization of the analytical conditions was carried out to achieve the best signal-to-background ratio and consequently an absolute limit of detection of 1 fg. Some possible interferents of the method were evaluated. The method was evaluated by determining indium in blood, urine, soil, and urban dust samples. Recoveries between 99.17 and 109.17% are reported. A precision of 4.1% at the 10 ng g -1 level in water standards was achieved. copyright 1998 Society for Applied Spectroscopy

Anomalous electrical properties of Pbsub(1-x)Snsub(x)Te layers with indium impurity

International Nuclear Information System (INIS)

Gejman, K.I.; Drabkin, I.A.; Matveenko, A.V.; Mozhaev, E.A.; Parfen'ev, R.V.

1977-01-01

Galvanomagnetic properties of indium doped (5x10 -3 -2x10 -1 at.% In) Pbsub(1-x)Snsub(x)Te monocrystal layers of n-type (x=0.1 - 0.22) sprayed on the (3) spalls of BaF 2 have been investigated. The layers with In display high homogeneity and lower electron density at 77 K, than the layers without In. With decreasing temperature below 20 K in the indium doped Pbsub(1-x)Snsub(x)Te layers an anomalous sharp increase of the electron density calculated from the Hall coefficient and reduction in electron mobility have been observed. The phenomenon under observation is related to the behaviour of indium under conditions of a possible structural phase transition initiated by introducing tin into PbTe. Investigation of the Shubnikov-de Gaas (SG) oscillations confirms the anomalous temperature dependence of the electron density. Distinctive features have been revealed in the SG oscillations of magnetoresistance in the Pbsub(1-x)Snsub(x)Te layers with In and without it, caused by deformations occurring in the films due to different coefficients of linear expansion of the material and a substrate. The splitting energy in the conduction band of the Pbsub(1-x)Snsub(x)Te layers has been determined, and the shift constant of the deformation potential has been estimated

Development and test of ion emitter modules for the projects ASPOC/CLUSTER (8th project year) and EQUATOR-S (4th project year). Final report

International Nuclear Information System (INIS)

Fehringer, H.M.; Ruedenauer, F.G.; Steiger, W.

1997-02-01

Not only was the failure of flight V001 of the newly developed ARIANE-V rocket a disaster for the European space industry and a drawback in the highly competitive launcher business, with the loss of its payload, ESA's 4 scientific CLUSTER satellites, also the work and expectations of hundreds of scientists and engineers were buried in the swamps of French Guyana. The Austrian experiment ASPOC, for which ion emitters have been developed under the contract reported here, was one of the 12 instruments onboard. In a meeting following the launch failure ESA's Science Policy Committee (SPC) decided to immediately rebuild one CLUSTER satellite and use the instrument spare models as the payload. This new mission was called PHOENIX. Furthermore, the SPC initiated studies to look for options of a CLUSTER reflight. The final decision about the future of the CLUSTER project is now due in February 1997. Since ASPOC has been lost, this report only very shortly deals with the work done up to the launch date. More important are two aspects: First, the ion emitters, the product which has been developed within this long term project, are of such high quality that they survived both the explosion of the rocket and the subsequent free fall from 3.6 km height. Ten ion emitters have been recovered from the debris and all of them were still working well. Second, new applications both in the scientific and in the commercial area have been found for the indium ion sources. Under an ESA contract their potential use as ion thrusters has recently successfully been studied. A further contract now has been placed for the development of a prototype ion thruster. Furthermore, the indium ion source has been selected as the primary ion emitter for the time of flight mass spectrometer COSIMA, a key instrument of the ROSETTA mission. Concerning EQUATOR-S, a new set of ion emitter modules has to be built, as those originally foreseen for EQUATOR-S are now being used for PHOENIX. The respective

Structural, optical and electrical properties of indium tin oxide thin films prepared by spray pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Benamar, E.; Rami, M.; Messaoudi, C.; Sayah, D.; Ennaoui, A. [Deptartmento de Physique, Laboratoire de Physique des Materiaux, Faculte des Sciences, BP 1014, Ave Inb Battouta, Rabat (Morocco)

1998-11-27

Spray pyrolysis process has been used to deposit highly transparent and conducting films of tin-doped indium oxide onto glass substrates. The electrical, structural and optical properties have been investigated as a function of various deposition parameters namely dopant concentrations, temperature and nature of substrate. The morphology of the surface as a function of the substrate temperature has been studied using atomic force microscopy. XRD has shown that deposited films are polycrystalline without second phases and have a preferred orientation (4 0 0). Indium tin oxide layers with low resistivity values around 4x10{sup -5} {Omega} cm and transmission coefficients in the visible and near-infrared range of about 85-90% have been easily obtained

Low-temperature grown indium oxide nanowire-based antireflection coatings for multi-crystalline silicon solar cells

Energy Technology Data Exchange (ETDEWEB)

Wang, Yu-Cian; Chen, Chih-Yao; Chen, I Chen [Institute of Materials Science and Engineering, National Central University, Taoyuan (China); Kuo, Cheng-Wen; Kuan, Ta-Ming; Yu, Cheng-Yeh [TSEC Corporation, Hsinchu (China)

2016-08-15

Light harvesting by indium oxide nanowires (InO NWs) as an antireflection layer on multi-crystalline silicon (mc-Si) solar cells has been investigated. The low-temperature growth of InO NWs was performed in electron cyclotron resonance (ECR) plasma with an O{sub 2}-Ar system using indium nanocrystals as seed particles via the self-catalyzed growth mechanism. The size-dependence of antireflection properties of InO NWs was studied. A considerable enhancement in short-circuit current (from 35.39 to 38.33 mA cm{sup -2}) without deterioration of other performance parameters is observed for mc-Si solar cells coated with InO NWs. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Progress Report: Feasibility Study of an Indium Scintillator Solar Neutrino Experiment

International Nuclear Information System (INIS)

Bellefon, A. de; Barloutaud, R.; Borg, A.; Ernwein, J.; Mosca, L.

1989-09-01

In this document, we report on the progress made to demonstrate the feasibility of an experiment which would measure for the first time the two line sources of solar neutrinos resulting from electron capture by 7 Be and from the p-e-p reaction inside the sun. The detector under study consists of scintillator containing 10 tons of Indium

Scaled-up solvothermal synthesis of nanosized metastable indium oxyhydroxide (InOOH) and corundum-type rhombohedral indium oxide (rh-In{sub 2}O{sub 3})

Energy Technology Data Exchange (ETDEWEB)

Schlicker, Lukas; Bekheet, Maged F.; Gurlo, Aleksander [Technische Univ. Berlin (Germany). Fachgebiet Keramische Werkstoffe

2017-03-01

Phase pure metastable indium oxyhydroxide (InOOH) with crystallite size in the range ca. 2-7 nm is synthesized by a nonaqueous solvothermal synthesis route in ethanol. The influence of synthesis parameters such as temperature, basicity (pH), synthesis time, and water content is carefully addressed. T-pH maps summarize the impact of synthesis temperature and pH and reveal that phase pure InOOH is obtained in water-free solutions at mild temperatures (150-180 C) in highly basic conditions (pH>12). Subsequent calcination of InOOH at 375-700 C in ambient air atmosphere results in metastable nanoscaled rhombohedral indium oxide (rh-In{sub 2}O{sub 3}). The synthesis protocol for phase pure nanocrystalline InOOH material was successfully upscaled allowing for obtaining ca. 3 g of phase-pure InOOH with a yield of ca. 78%. The upscaled InOOH and rh-In{sub 2}O{sub 3} batches are now available for a detailed in-situ characterization of the mechanism of decomposition of InOOH to rh-In{sub 2}O{sub 3} to c-In{sub 2}O{sub 3} as well as for the characterization of the functional properties of InOOH and rh-In{sub 2}O{sub 3} materials.

Electrostatically driven resonance energy transfer in "cationic" biocompatible indium phosphide quantum dots.

Science.gov (United States)

Devatha, Gayathri; Roy, Soumendu; Rao, Anish; Mallick, Abhik; Basu, Sudipta; Pillai, Pramod P

2017-05-01

Indium Phosphide Quantum Dots (InP QDs) have emerged as an alternative to toxic metal ion based QDs in nanobiotechnology. The ability to generate cationic surface charge, without compromising stability and biocompatibility, is essential in realizing the full potential of InP QDs in biological applications. We have addressed this challenge by developing a place exchange protocol for the preparation of cationic InP/ZnS QDs. The quaternary ammonium group provides the much required permanent positive charge and stability to InP/ZnS QDs in biofluids. The two important properties of QDs, namely bioimaging and light induced resonance energy transfer, are successfully demonstrated in cationic InP/ZnS QDs. The low cytotoxicity and stable photoluminescence of cationic InP/ZnS QDs inside cells make them ideal candidates as optical probes for cellular imaging. An efficient resonance energy transfer ( E ∼ 60%) is observed, under physiological conditions, between the cationic InP/ZnS QD donor and anionic dye acceptor. A large bimolecular quenching constant along with a linear Stern-Volmer plot confirms the formation of a strong ground state complex between the cationic InP/ZnS QDs and the anionic dye. Control experiments prove the role of electrostatic attraction in driving the light induced interactions, which can rightfully form the basis for future nano-bio studies between cationic InP/ZnS QDs and anionic biomolecules.

Compositional influence on the electrical performance of zinc indium tin oxide transparent thin-film transistors

International Nuclear Information System (INIS)

Marsal, A.; Carreras, P.; Puigdollers, J.; Voz, C.; Galindo, S.; Alcubilla, R.; Bertomeu, J.; Antony, A.

2014-01-01

In this work, zinc indium tin oxide layers with different compositions are used as the active layer of thin film transistors. This multicomponent transparent conductive oxide is gaining great interest due to its reduced content of the scarce indium element. Experimental data indicate that the incorporation of zinc promotes the creation of oxygen vacancies, which results in a higher free carrier density. In thin-film transistors this effect leads to a higher off current and threshold voltage values. The field-effect mobility is also strongly degraded, probably due to coulomb scattering by ionized defects. A post deposition annealing in air reduces the density of oxygen vacancies and improves the field-effect mobility by orders of magnitude. Finally, the electrical characteristics of the fabricated thin-film transistors have been analyzed to estimate the density of states in the gap of the active layers. These measurements reveal a clear peak located at 0.3 eV from the conduction band edge that could be attributed to oxygen vacancies. - Highlights: • Zinc promotes the creation of oxygen vacancies in zinc indium tin oxide transistors. • Post deposition annealing in air reduces the density of oxygen. • Density of states reveals a clear peak located at 0.3 eV from the conduction band

Nuclear structure studies on indium and tin isotope chains by means of laser spectroscopy

International Nuclear Information System (INIS)

Eberz, J.

1986-11-01

In a collaboration with GSI in Darmstadt and ISOLDE in Geneva the hyperfine structure (HFS) and the isotope shift (IS) of the indium isotopes from 104 In - 127 In in their ground and isomeric states could be studied. Additionally the tin isotopes 109 Sn and 111 Sn could be measured. In tin the transition 5p 2 1 S 0 → 5p6s 3 P 1 with λ = 563 nm was studied. In indium the transition 5p 2 P 1/2 → 6s 2 S 1/2 with λ = 410 nm and 5p 2 P 3/2 → 6s 2 S 1/2 with λ = 451 nm could be measured. The magnetic dipole moments and electric quadrupole moments determined from the measurements of the HFS can be sufficiently explained in the framework of the single-particle model. From the moments the configurations and spins of the studied nuclear states can be stated. In 109 Sn the nuclear spin was determined to I = 5/2. The measurement of the IS in two lines in 108 In allowed regarding the coupling rules for nuclear moments the determination of the nuclear spin. The spin of the 40 m isomers of the 108m In can be stated to I = 2. The mean square nuclear charge radius exhibits a parabolic slope the quadratic part of which with a maximum in the shell center at N = 66 between the neutron numbers N = 50 and N = 82 can be understood as sum of contributions of a surface correlation, i.e. a quadrupole deformation as well as eventually present higher order terms or a change of the surface skin density. The deformation determinable by this description is both for tin and for indium essentially larger than the deformation from the B(E2) values of tin or from the intrinsic quadrupole moments in indium derived from the HFS. (orig./HSI) [de

Comparison of different pathways in metamorphic graded buffers on GaAs substrate: Indium incorporation with surface roughness

International Nuclear Information System (INIS)

Kumar, Rahul; Mukhopadhyay, P.; Bag, A.; Jana, S. Kr.; Chakraborty, A.; Das, S.; Mahata, M. Kr.; Biswas, D.

2015-01-01

Highlights: • In(Al,Ga)As metamorphic buffers on GaAs have been grown. • Surface morphology, strain relaxation and compositional variation have been studied. • Al containing buffers shows inferior surface roughness. • Surface roughness modulates the indium incorporation rate. - Abstract: In this work, compositionally graded In(Al,Ga)As metamorphic buffers (MBs) on GaAs substrate have been grown by MBE through three different paths. A comparative study has been done to comprehend the effect of underlying MB on the constant composition InAlAs healing layer by analyzing the relaxation behaviour, composition and surface morphology of the grown structures. The compositional variation between the constant composition healing layers on top of graded MB has been observed in all three samples although the growth conditions have been kept same. Indium incorporation rate has been found to be dependent on underlying MB. By combining the result of atomic force microscopy, photo-luminescence and X-ray reciprocal space mapping, varying surface roughness has been proposed as the probable driving force behind different Indium incorporation rate

Comparison of different pathways in metamorphic graded buffers on GaAs substrate: Indium incorporation with surface roughness

Energy Technology Data Exchange (ETDEWEB)

Kumar, Rahul, E-mail: rkp203@gmail.com [Advanced Technology Development Centre, Indian Institute of Technology, Kharagpur 721302 (India); Mukhopadhyay, P. [Rajendra Mishra School of Engineering Entrepreneurship, Indian Institute of Technology, Kharagpur 721302 (India); Bag, A.; Jana, S. Kr. [Advanced Technology Development Centre, Indian Institute of Technology, Kharagpur 721302 (India); Chakraborty, A. [Department of Electronics and Electrical Communication Engineering, Indian Institute of Technology, Kharagpur 721 302 (India); Das, S.; Mahata, M. Kr. [Advanced Technology Development Centre, Indian Institute of Technology, Kharagpur 721302 (India); Biswas, D. [Department of Electronics and Electrical Communication Engineering, Indian Institute of Technology, Kharagpur 721 302 (India)

2015-01-01

Highlights: • In(Al,Ga)As metamorphic buffers on GaAs have been grown. • Surface morphology, strain relaxation and compositional variation have been studied. • Al containing buffers shows inferior surface roughness. • Surface roughness modulates the indium incorporation rate. - Abstract: In this work, compositionally graded In(Al,Ga)As metamorphic buffers (MBs) on GaAs substrate have been grown by MBE through three different paths. A comparative study has been done to comprehend the effect of underlying MB on the constant composition InAlAs healing layer by analyzing the relaxation behaviour, composition and surface morphology of the grown structures. The compositional variation between the constant composition healing layers on top of graded MB has been observed in all three samples although the growth conditions have been kept same. Indium incorporation rate has been found to be dependent on underlying MB. By combining the result of atomic force microscopy, photo-luminescence and X-ray reciprocal space mapping, varying surface roughness has been proposed as the probable driving force behind different Indium incorporation rate.

The Effect of Annealing on Nanothick Indium Tin Oxide Transparent Conductive Films for Touch Sensors

Directory of Open Access Journals (Sweden)

Shih-Hao Chan

2015-01-01

Full Text Available This study aims to discuss the sheet resistance of ultrathin indium tin oxide (ITO transparent conductive films during the postannealing treatment. The thickness of the ultrathin ITO films is 20 nm. They are prepared on B270 glass substrates at room temperature by a direct-current pulsed magnetron sputtering system. Ultrathin ITO films with high sheet resistance are commonly used for touch panel applications. As the annealing temperature is increased, the structure of the ultrathin ITO film changes from amorphous to polycrystalline. The crystalline of ultrathin ITO films becomes stronger with an increase of annealing temperature, which further leads to the effect of enhanced Hall mobility. A postannealing treatment in an atmosphere can enhance the optical transmittance owing to the filling of oxygen vacancies, but the sheet resistance rises sharply. However, a higher annealing temperature, above 250°C, results in a decrease in the sheet resistance of ultrathin ITO films, because more Sn ions become an effective dopant. An optimum sheet resistance of 336 Ω/sqr was obtained for ultrathin ITO films at 400°C with an average optical transmittance of 86.8% for touch sensor applications.

Kinetics Study of Silver Electrocrystallization on (3-mercaptopropyl)trimethoxysilane-grafted Indium Tin Oxide Plastic Substrate

International Nuclear Information System (INIS)

Hau, Nga Yu; Chang, Ya-Huei; Feng, Shien-Ping

2015-01-01

Highlights: • The larger charge transfer coefficient supports that MPS promotes electrodeposition. • ACV shows that electron-transfer rate enhanced by 2.5 times after MPS treatment. • The fitting of CA defined the Ag nucleation mode on blank and MPS-grafted ITO-PEN. • MPS treatment changed the nucleation mode from 2-step to a single step one. - Abstract: 3-mercaptopropyl-trimethoxysilane (MPS) self-assembled monolayer (SAM) has been demonstrated as effective promoters to enable direct electroplated metallization on indium tin oxide (ITO) plastic substrate. In this paper, the detail kinetics in Ag electrocrystallization on MPS-grafted ITO-PEN is reported. Contact angle measurement provides evidence of bridging-link effect between the sulfur head groups of MPS and the Ag + ions in the electrolyte. Electrochemical techniques including cyclic voltammetry and Tafel plot were used to investigate the redox kinetics. Quantitative evaluation was conducted by alternating current voltammetry to determine the rate constant of electron transfer. The chronoamperograms and their fitting results suggest a combined model with two-dimensional/three-dimensional nucleation transition and Shariker-Hills model for electroplated Ag on blank ITO-PEN and MPS-grafted ITO-PEN respectively

Switchable Super-Hydrophilic/Hydrophobic Indium Tin Oxide (ITO) Film Surfaces on Reactive Ion Etching (RIE) Textured Si Wafer.

Science.gov (United States)

Kim, Hwa-Min; Litao, Yao; Kim, Bonghwan

2015-11-01

We have developed a surface texturing process for pyramidal surface features along with an indium tin oxide (ITO) coating process to fabricate super-hydrophilic conductive surfaces. The contact angle of a water droplet was less than 5 degrees, which means that an extremely high wettability is achievable on super-hydrophilic surfaces. We have also fabricated a super-hydrophobic conductive surface using an additional coating of polytetrafluoroethylene (PTFE) on the ITO layer coated on the textured Si surface; the ITO and PTFE films were deposited by using a conventional sputtering method. We found that a super-hydrophilic conductive surface is produced by ITO coated on the pyramidal Si surface (ITO/Si), with contact angles of approximately 0 degrees and a resistivity of 3 x 10(-4) Ω x cm. These values are highly dependent on the substrate temperature during the sputtering process. We also found that the super-hydrophobic conductive surface produced by the additional coating of PTFE on the pyramidal Si surface with an ITO layer (PTFE/ITO/Si) has a contact angle of almost 160 degrees and a resistivity of 3 x 10(-4) Ω x cm, with a reflectance lower than 9%. Therefore, these processes can be used to fabricate multifunctional features of ITO films for switchable super-hydrophilic and super-hydrophobic surfaces.

Ammonium ions determination with polypyrrole modified electrode

Directory of Open Access Journals (Sweden)

Luiz Henrique Dall´Antonia

2007-03-01

Full Text Available The present work relates the preparation of polypyrrole films (PPy deposited on surfaces of glass carbon, nickel and ITO (tin oxide doped with indium on PET plastic, in order to study the ammonium detection. The popypyrrole films were polymerized with dodecylbenzenesulfonate (DBSA on the electrodes, at + 0,70 V vs. Ag/AgCl, based on a solution containing the pyrrole monomer and the amphiphilic salt. Films deposited on glass carbon presented better performance. Cyclic voltammetries, between – 1,50 to + 0,5 V vs. Ag/AgCl, were repeated adding different concentrations of NH4Cl, in order to observe the behavior of the film as a possible detector of ions NH4+. The peak current for oxidation varies with the concentration of ammonium. A linear region can be observed in the band of 0 to 80 mM, with a sensibility (Sppy approximately similar to 4,2 mA mM-1 cm-2, showing the efficacy of the electrodes as sensors of ammonium ions. The amount of deposited polymer, controlled by the time of growth, does not influence on the sensor sensibility. The modified electrode was used to determine ammonium in grounded waters.

Noninvasive detection of rejection of transplanted hearts with indium-111-labeled lymphocytes

International Nuclear Information System (INIS)

Eisen, H.J.; Eisenberg, S.B.; Saffitz, J.E.; Bolman, R.M. III; Sobel, B.E.; Bergmann, S.R.

1987-01-01

To determine whether cardiac transplant rejection can be detected noninvasively with indium-111 ( 111 In)-labeled lymphocytes, we studied 11 dogs with thoracic heterotopic cardiac transplants without immunosuppression and five dogs with transplants treated with cyclosporine (10 mg/kg/day) and prednisone (1 mg/kg/day). All were evaluated sequentially with gamma scintigraphy after administration of 150 to 350 muCi of autologous 111 In-lymphocytes. Technetium-99m-labeled red blood cells (1 to 3 mCi) were used for correction of radioactivity in the blood pool attributable to circulating labeled lymphocytes. Lymphocyte infiltration was quantified as the ratio of indium in the myocardium of the transplant or native heart compared with that in blood (indium excess, IE). Results were correlated with mechanical and electrical activity of allografts and with histologic findings in sequential biopsy specimens. In untreated dogs (n = 11), IE was 15.5 +/- 7.0 (SD) in transplanted hearts undergoing rejection and 0.4 +/- 1.1 in native hearts on the day before animals were killed. In dogs treated with cyclosporine and prednisone (n = 5), IE was minimal in allografts during the course of immunosuppression (0.8 +/- 0.4) and increased to 22.9 +/- 11.1 after immunosuppression was stopped. Scintigraphic criteria of rejection (IE greater than 2 SD above that in native hearts) correlated with results of biopsies indicative of rejection and appeared before electrophysiologic or mechanical manifestations of dysfunction. Thus infiltration of labeled lymphocytes in allografts, indicative of rejection, is detectable noninvasively by gamma scintigraphy and provides a sensitive approach potentially applicable to clinical monitoring for early detection of rejection and guidance for titration of immunosuppressive measures

Ensembles of indium phosphide nanowires: physical properties and functional devices integrated on non-single crystal platforms

International Nuclear Information System (INIS)

Kobayashi, Nobuhiko P.; Lohn, Andrew; Onishi, Takehiro; Mathai, Sagi; Li, Xuema; Straznicky, Joseph; Wang, Shih-Yuan; Williams, R.S.; Logeeswaran, V.J.; Islam, M.S.

2009-01-01

A new route to grow an ensemble of indium phosphide single-crystal semiconductor nanowires is described. Unlike conventional epitaxial growth of single-crystal semiconductor films, the proposed route for growing semiconductor nanowires does not require a single-crystal semiconductor substrate. In the proposed route, instead of using single-crystal semiconductor substrates that are characterized by their long-range atomic ordering, a template layer that possesses short-range atomic ordering prepared on a non-single-crystal substrate is employed. On the template layer, epitaxial information associated with its short-range atomic ordering is available within an area that is comparable to that of a nanowire root. Thus the template layer locally provides epitaxial information required for the growth of semiconductor nanowires. In the particular demonstration described in this paper, hydrogenated silicon was used as a template layer for epitaxial growth of indium phosphide nanowires. The indium phosphide nanowires grown on the hydrogenerated silicon template layer were found to be single crystal and optically active. Simple photoconductors and pin-diodes were fabricated and tested with the view towards various optoelectronic device applications where group III-V compound semiconductors are functionally integrated onto non-single-crystal platforms. (orig.)

Ensembles of indium phosphide nanowires: physical properties and functional devices integrated on non-single crystal platforms

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Nobuhiko P.; Lohn, Andrew; Onishi, Takehiro [University of California, Santa Cruz (United States). Baskin School of Engineering; NASA Ames Research Center, Nanostructured Energy Conversion Technology and Research (NECTAR), Advanced Studies Laboratories, Univ. of California Santa Cruz, Moffett Field, CA (United States); Mathai, Sagi; Li, Xuema; Straznicky, Joseph; Wang, Shih-Yuan; Williams, R.S. [Hewlett-Packard Laboratories, Information and Quantum Systems Laboratory, Palo Alto, CA (United States); Logeeswaran, V.J.; Islam, M.S. [University of California Davis, Electrical and Computer Engineering, Davis, CA (United States)

2009-06-15

A new route to grow an ensemble of indium phosphide single-crystal semiconductor nanowires is described. Unlike conventional epitaxial growth of single-crystal semiconductor films, the proposed route for growing semiconductor nanowires does not require a single-crystal semiconductor substrate. In the proposed route, instead of using single-crystal semiconductor substrates that are characterized by their long-range atomic ordering, a template layer that possesses short-range atomic ordering prepared on a non-single-crystal substrate is employed. On the template layer, epitaxial information associated with its short-range atomic ordering is available within an area that is comparable to that of a nanowire root. Thus the template layer locally provides epitaxial information required for the growth of semiconductor nanowires. In the particular demonstration described in this paper, hydrogenated silicon was used as a template layer for epitaxial growth of indium phosphide nanowires. The indium phosphide nanowires grown on the hydrogenerated silicon template layer were found to be single crystal and optically active. Simple photoconductors and pin-diodes were fabricated and tested with the view towards various optoelectronic device applications where group III-V compound semiconductors are functionally integrated onto non-single-crystal platforms. (orig.)

Transparent indium zinc oxide thin films used in photovoltaic cells based on polymer blends

International Nuclear Information System (INIS)

Besleaga, Cristina; Ion, L.; Ghenescu, Veta; Socol, G.; Radu, A.; Arghir, Iulia; Florica, Camelia; Antohe, S.

2012-01-01

Indium zinc oxide (IZO) thin films were obtained using pulsed laser deposition. The samples were prepared by ablation of targets with In concentrations, In/(In + Zn), of 80 at.%, at low substrate temperatures under reactive atmosphere. IZO films were used as transparent electrodes in polymer-based – poly(3-hexylthiophene) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-(6,6)C61 1:1 blend – photovoltaic cells. The action spectra measurements revealed that IZO-based photovoltaic structures have performances comparable with those using indium–tin–oxide as transparent electrode. - Highlights: ► Indium zinc oxide films were grown by pulsed laser deposition at room temperature. ► The films had large free carrier density and reasonably high mobility. ► These films fit for transparent electrodes in polymer-based photovoltaic cells.

Surface enhanced Raman scattering in organic thin films covered with silver, indium and magnesium

International Nuclear Information System (INIS)

Salvan, Georgeta; Zahn, Dietrich R.T.; Paez, Beynor

2004-01-01

In situ resonant Raman spectroscopy was applied for the investigation of the interface formation between silver, indium and magnesium with polycrystalline organic semiconductor layers of 3,4,9,10-perylene tetra-carboxylic dianhydride (PTCDA). The spectral region of internal as well as external vibrational modes was recorded in order to achieve information related to the chemistry and the structure of the interface as well as to morphology of the metal layer. The experiments benefit from a strong enhancement of the internal mode scattering intensities which is induced by the rough morphology of deposited metals leading to surface enhanced Raman scattering (SERS). The external modes, on the other hand, are attenuated at different rates indicating that the diffusion of the metal atoms into the crystalline layers is highest for indium and lowest for magnesium

DX centers in indium aluminum arsenide heterostructures

Science.gov (United States)

Sari, Huseyin

DX centers are point defects observed in many n-type doped III-V compound semi conductors. They have unique properties, which include large differences between their optical and thermal ionization energies, and a temperature dependence of the capture cross-sections. As a result of these properties DX centers exhibit a reduction in free carrier concentration and a large persistent photoconductivity (PPC) effect. DX centers also lead to a shift in the threshold voltage of modulation doped field effect transistors (MODFET) structures, at low temperatures. Most of the studies on this defect have been carried out on the Ga xAl1-xAs material system. However, to date there is significantly less work on DX centers in InxAl1-xAs compounds. This is partly due to difficulties associated with the growth of defect free materials other than lattice matched In0.52Al 0.48As on InP and partly because the energy level of the DX center is in resonance with the conduction band in In0.52Al0.48As. The purpose of this dissertation is to extend the DX center investigation to InAlAs compounds, primarily in the indirect portion of the InAlAs bandgap. In this work the indium composition dependence of the DX centers in In xAl1-xAs/InyGa1-yAs-based heterostructure is studied experimentally. Different InxAl 1-xAs epitaxial layers with x = 0.10, x = 0.15, x = 0.20, and x = 0.34 in a MODFET-like heterostructure were grown by Molecular Beam Epitaxy (MBE) on (001) GaAs substrates. In order to compensate the lattice mismatch between epitaxial layers and their substrates, step-graded buffer layers with indium composition increments of x = 0.10, every 2000 A, were used. For the samples grown with different indium contents Hall measurements as a function of both temperature and different cooling biases were performed in order to determine their carrier concentrations. A self consistent Poisson-Schrodinger numerical software is used to model the heterostructures. With the help of this numerical model

Influence of thermal treatment in N{sub 2} atmosphere on chemical, microstructural and optical properties of indium tin oxide and nitrogen doped indium tin oxide rf-sputtered thin films

Energy Technology Data Exchange (ETDEWEB)

Stroescu, H.; Anastasescu, M.; Preda, S.; Nicolescu, M.; Stoica, M. [Institute of Physical Chemistry “Ilie Murgulescu” of the Romanian Academy, Spl. Independentei 202, 060021 Bucharest (Romania); Stefan, N. [National Institute for Lasers, Plasma and Radiation Physics, Atomistilor 409, RO-77125, Bucharest-Magurele (Romania); Kampylafka, V.; Aperathitis, E. [FORTH-IESL, Crete (Greece); Modreanu, M. [Tyndall National Institute, University College Cork, Cork (Ireland); Zaharescu, M. [Institute of Physical Chemistry “Ilie Murgulescu” of the Romanian Academy, Spl. Independentei 202, 060021 Bucharest (Romania); Gartner, M., E-mail: mgartner@icf.ro [Institute of Physical Chemistry “Ilie Murgulescu” of the Romanian Academy, Spl. Independentei 202, 060021 Bucharest (Romania)

2013-08-31

We report the influence of the normal thermal treatment (TT) and of rapid thermal annealing (RTA) on the microstructural, optical and electrical properties of indium tin oxide (ITO) and nitrogen doped indium tin oxide (ITO:N) thin films. The TT was carried out for 1 h at 400 °C and the RTA for 1 min up to 400 °C, both in N{sub 2} atmosphere. The ITO and ITO:N films were deposited by reactive sputtering in Argon, and respectively Nitrogen plasma, on Si with (100) and (111) orientation. The present study brings data about the microstructural and optical properties of ITO thin films with thicknesses around 300–400 nm. Atomic Force Microscopy analysis showed the formation of continuous and homogeneous films, fully covered by quasi-spherical shaped particles, with higher roughness values on Si(100) as compared to Si(111). Spectroscopic ellipsometry allowed the determination of film thickness, optical band gap as well as of the dispersion curves of n and k optical constants. X-ray diffraction analysis revealed the presence of diffraction peaks corresponding to the same nominal bulk composition of ITO, but with different intensities and preferential orientation depending on the substrate, atmosphere of deposition and type of thermal treatment. - Highlights: ► Stability of the films can be monitored by experimental ellipsometric spectra. ► The refractive index of indium tin oxide film on 0.3–30 μm range is reported. ► Si(100) substrate induces rougher film surfaces than Si(111). ► Rapid thermal annealing and normal thermal treatment lead to stable conductive film. ► The samples have a higher preferential orientation after rapid thermal annealing.

Effect of dislocations on the open-circuit voltage, short-circuit current and efficiency of heteroepitaxial indium phosphide solar cells

Science.gov (United States)

Jain, Raj K.; Flood, Dennis J.

1990-01-01

Excellent radiation resistance of indium phosphide solar cells makes them a promising candidate for space power applications, but the present high cost of starting substrates may inhibit their large scale use. Thin film indium phosphide cells grown on Si or GaAs substrates have exhibited low efficiencies, because of the generation and propagation of large number of dislocations. Dislocation densities were calculated and its influence on the open circuit voltage, short circuit current, and efficiency of heteroepitaxial indium phosphide cells was studied using the PC-1D. Dislocations act as predominant recombination centers and are required to be controlled by proper transition layers and improved growth techniques. It is shown that heteroepitaxial grown cells could achieve efficiencies in excess of 18 percent AMO by controlling the number of dislocations. The effect of emitter thickness and surface recombination velocity on the cell performance parameters vs. dislocation density is also studied.

Optical emission spectroscopy during fabrication of indium-tin-oxynitride films by RF-sputtering

International Nuclear Information System (INIS)

Koufaki, M.; Sifakis, M.; Iliopoulos, E.; Pelekanos, N.; Modreanu, M.; Cimalla, V.; Ecke, G.; Aperathitis, E.

2006-01-01

Indium-tin-oxide (ITO) and indium-tin-oxynitride (ITON) films have been deposited on glass by rf-sputtering from an ITO target, using Ar plasma and N 2 plasma, respectively, and different rf-power. Optical emission spectroscopy (OES) was employed to identify the species present in the plasma and to correlate them with the properties of the ITO and ITON thin films. Emission lines of ionic In could only be detected in N 2 plasma, whereas in the Ar plasma additional lines corresponding to atomic In and InO, were detected. The deposition rate of thin films was correlated with the In species, rather than the nitrogen species, emission intensity in the plasma. The higher resistivity and lower carrier concentration of the ITON films, as compared to the respective properties of the ITO films, were attributed to the incorporation of nitrogen, instead of oxygen, in the ITON structure

Ab-initio modelling of thermodynamics and kinetics of point defects in indium oxide

International Nuclear Information System (INIS)

Agoston, Peter; Klein, Andreas; Albe, Karsten; Erhart, Paul

2008-01-01

The electrical and optical properties of indium oxide films strongly vary with the processing parameters. Especially the oxygen partial pressure and temperature determine properties like electrical conductivity, composition and transparency. Since this material owes its remarkable properties like the intrinsic n-type conductivity to its defect chemistry, it is important to understand both, the equilibrium defect thermodynamics and kinetics of the intrinsic point defects. In this contribution we present a defect model based on DFT total energy calculations using the GGA+U method. Further, the nudged elastic band method is employed in order to obtain a set of migration barriers for each defect species. Due to the complicated crystal structure of indium oxide a Kinetic Monte-Carlo algorithm was implemented, which allows to determine diffusion coefficients. The bulk tracer diffusion constant is predicted as a function of oxygen partial pressure, Fermi level and temperature for the pure material

Tailor-made surface plasmon polaritons above the bulk plasma frequency: a design strategy for indium tin oxide

International Nuclear Information System (INIS)

Brand, S; Abram, R A; Kaliteevski, M A

2010-01-01

A simple phase-matching approach is employed as a design aid to engineer surface plasmon polariton states at the interface of an indium tin oxide layer on the top of a Bragg reflector. By altering the details of the reflector, and in particular the ordering of the layers and the thickness of the layer adjacent to the indium tin oxide, it is possible to readily adjust the energy of these states. Examples of structures engineered to give rise to distinctive features in the reflectivity spectra above the bulk screened plasma frequency for states of both possible polarizations are presented.

Indium antimonide nanowires arrays for promising thermoelectric converters

Directory of Open Access Journals (Sweden)

Gorokh G. G.

2015-02-01

Full Text Available The authors have theoretically substantiated the possibility to create promising thermoelectric converters based on quantum wires. The calculations have shown that the use of quantum wires with lateral dimensions smaller than quantum confinement values and high concentration and mobility of electrons, can lead to a substantial cooling of one of the contacts up to tens of degrees and to the heating of the other. The technological methods of manufacturing of indium antimonide nanowires arrays with high aspect ratio of the nanowire diameters to their length in the modified nanoporous anodic alumina matrixes were developed and tested. The microstructure and composition of the formed nanostructures were investigated. The electron microscopy allowed establishing that within each pore nanowires are formed with diameters of 35 nm and a length of 35 microns (equal to the matrix thickness. The electron probe x-ray microanalysis has shown that the atomic ratio of indium and antimony in the semiconductor nanostructures amounted to 38,26% and 61,74%, respectively. The current-voltage measurement between the upper and lower contacts of Cu/InSb/Cu structure (1 mm2 has shown that at 2.82 V negative voltage at the emitter contact, current density is 129,8 A/cм2, and the collector contact is heated up to 75 degrees during 150 sec. Thus, the experimental results confirmed the theoretical findings that the quantum wire systems can be used to create thermoelectric devices, which can be widely applied in electronics, in particular, for cooling integrated circuits (processors, thermal controlling of the electrical circuits by changing voltage value.

Indium-111 platelet scintigraphy and two-dimensional echocardiography for detection of left ventricular thrombus: influence of clot size and age

International Nuclear Information System (INIS)

Seabold, J.E.; Schroeder, E.C.; Conrad, G.R.

1987-01-01

Two-dimensional echocardiography and indium-111 platelet scintigraphy were performed on 50 dogs to determine the influence of clot age and size on the detection of experimentally induced left ventricular mural thrombus. Thrombus was induced by apical infarction and injection of a sclerosing agent and thrombin. The animals were classified into four groups according to the time of indium-111 platelet injection after thrombus induction: Group I (17 dogs, 1/2 hour after induction; 3 dogs, before induction), Group II (12 dogs, 24 hours after induction) and Group III (12 dogs, 1 week after induction). In Group IV (six control dogs) apical infarction was produced, but thrombin was not injected; indium-111 platelets were injected 1/2 to 1 hour after infarction. The dogs were studied by indium-111 platelet scintigraphy and by two-dimensional echocardiography 1/2 to 5 hours (Group I) and 1 to 5 and up to 72 hours (Groups II to IV) after platelet administration and before death was induced. Two-dimensional echocardiography showed the best overall sensitivity for detection of acute thrombus (97%; 29 of 30). The sensitivity of indium-111 platelet scintigraphy was 86% (18 of 21) for clots greater than or equal to 0.08 ml in size, and 67% (20 of 30) for detection of all clots. Thrombus did not form in 14 dogs of Groups I to III and in 6 of 6 control dogs. The specificity of scintigraphy was 100% (20 of 20) compared with 80% (16 of 20) for echocardiography. Echocardiography was more sensitive than scintigraphy for detecting very small clots in this experimental model

Toxicological assessment of indium nitrate on aquatic organisms and investigation of the effects on the PLHC-1 fish cell line

Energy Technology Data Exchange (ETDEWEB)

Zurita, Jorge L. [National Institute of Toxicology and Forensic Sciences, Av. Dr Fedriani s/n, 41009, Seville (Spain); Jos, Angeles [Area of Toxicology, University of Seville, Prof. Garcia Gonzalez 2, 41012, Seville (Spain); Peso, Ana del; Salguero, Manuel [National Institute of Toxicology and Forensic Sciences, Av. Dr Fedriani s/n, 41009, Seville (Spain); Camean, Ana M. [Area of Toxicology, University of Seville, Prof. Garcia Gonzalez 2, 41012, Seville (Spain); Lopez-Artiguez, Miguel [National Institute of Toxicology and Forensic Sciences, Av. Dr Fedriani s/n, 41009, Seville (Spain); Repetto, Guillermo [National Institute of Toxicology and Forensic Sciences, Av. Dr Fedriani s/n, 41009, Seville (Spain); Area of Toxicology, University of Seville, Prof. Garcia Gonzalez 2, 41012, Seville (Spain)], E-mail: repetto@us.es

2007-11-15

Indium nitrate is mainly used as a semiconductor in batteries, for plating and other chemical and medical applications. There is a lack of available information about the adverse effects of indium compounds on aquatic organisms. Therefore, the toxic effects on systems from four trophic levels of the aquatic ecosystem were investigated. Firstly, the bacterium Vibrio fischeri, the alga Chlorella vulgaris and the cladoceran Daphnia magna were used in the toxicological evaluation of indium nitrate. The most sensitive model was V. fischeri, with a NOAEL of 0.02 and an EC{sub 50} of 0.04 mM at 15 min. Although indium nitrate should be classified as harmful to aquatic organisms, it is not expected to represent acute risk to the aquatic biota. Secondly, PLHC-1 fish cell line was employed to investigate the effects and mechanisms of toxicity. Although protein content, neutral red uptake, methylthiazol metabolization, lysosomal function and acetylcholinesterase activity were reduced in cells, stimulations were observed for metallothionein levels and succinate dehydrogenase and glucose-6-phosphate dehydrogenase activities. No changes were observed in ethoxyresorufin-O-deethylase activity. To clarify the main events in PLHC-1 cell death induced by indium nitrate, nine modulators were applied. They were related to oxidative stress ({alpha}-tocopherol succinate, mannitol and sodium benzoate), disruption of calcium homeostasis (BAPTA-AM and EGTA), thiol protection (1,4-dithiotreitol), iron chelation (deferoxiamine) or regulation of glutathione levels (2-oxothiazolidine-4-carboxylic acid and malic acid diethyl ester). The main morphological alterations were hydropic degeneration and loss of cells. At least, in partly, toxicity seems to be mediated by oxidative stress, and particularly by NADPH-dependent lipid peroxidation.

Toxicological assessment of indium nitrate on aquatic organisms and investigation of the effects on the PLHC-1 fish cell line

International Nuclear Information System (INIS)

Zurita, Jorge L.; Jos, Angeles; Peso, Ana del; Salguero, Manuel; Camean, Ana M.; Lopez-Artiguez, Miguel; Repetto, Guillermo

2007-01-01

Indium nitrate is mainly used as a semiconductor in batteries, for plating and other chemical and medical applications. There is a lack of available information about the adverse effects of indium compounds on aquatic organisms. Therefore, the toxic effects on systems from four trophic levels of the aquatic ecosystem were investigated. Firstly, the bacterium Vibrio fischeri, the alga Chlorella vulgaris and the cladoceran Daphnia magna were used in the toxicological evaluation of indium nitrate. The most sensitive model was V. fischeri, with a NOAEL of 0.02 and an EC 50 of 0.04 mM at 15 min. Although indium nitrate should be classified as harmful to aquatic organisms, it is not expected to represent acute risk to the aquatic biota. Secondly, PLHC-1 fish cell line was employed to investigate the effects and mechanisms of toxicity. Although protein content, neutral red uptake, methylthiazol metabolization, lysosomal function and acetylcholinesterase activity were reduced in cells, stimulations were observed for metallothionein levels and succinate dehydrogenase and glucose-6-phosphate dehydrogenase activities. No changes were observed in ethoxyresorufin-O-deethylase activity. To clarify the main events in PLHC-1 cell death induced by indium nitrate, nine modulators were applied. They were related to oxidative stress (α-tocopherol succinate, mannitol and sodium benzoate), disruption of calcium homeostasis (BAPTA-AM and EGTA), thiol protection (1,4-dithiotreitol), iron chelation (deferoxiamine) or regulation of glutathione levels (2-oxothiazolidine-4-carboxylic acid and malic acid diethyl ester). The main morphological alterations were hydropic degeneration and loss of cells. At least, in partly, toxicity seems to be mediated by oxidative stress, and particularly by NADPH-dependent lipid peroxidation

Highly sensitive colour change system within slight differences in metal ion concentrations based on homo-binuclear complex formation equilibrium for visual threshold detection of trace metal ions

International Nuclear Information System (INIS)

Mizuguchi, Hitoshi; Atsumi, Hiroshi; Hashimoto, Keigo; Shimada, Yasuhiro; Kudo, Yuki; Endo, Masatoshi; Yokota, Fumihiko; Shida, Junichi; Yotsuyanagi, Takao

2004-01-01

A new technique of expressing slight differences in metal ion concentrations by clear difference in colour was established for visual threshold detection of trace metal ions. The proposed method is based on rapid change of the mole fraction of the homo-binuclear complex (M 2 L) about a ligand in a narrow range of the total metal ion concentration (M T ) in a small excess, in case the second metal ion is bound to the reagent molecule which can bind two metal ions. Theoretical simulations showed that the highly sensitive colour change within slight differences in metal ion concentrations would be realized under the following conditions: (i) both of the stepwise formation constants of complex species are sufficiently large; (ii) the stepwise formation constant of the 1:1 complex (ML) is larger than that of M 2 L; and (iii) the absorption spectrum of M 2 L is far apart from the other species in the visible region. Furthermore, the boundary of the colour region in M T would be readily controlled by the total ligand concentration (L T ). Based on this theory, the proposed model was verified with the 3,3'-bis[bis(carboxymethyl)amino]methyl derivatives of sulphonephthalein dyes such as xylenol orange (XO), methylthymol blue (MTB), and methylxylenol blue (MXB), which can bind two metal ions at both ends of a π-electron conjugated system. The above-mentioned model was proved with the iron(III)-XO system at pH 2. In addition, MTB and MXB were suitable reagents for the visual threshold detection of trivalent metal ions such as iron(III), aluminium(III), gallium(III) and indium(III) ion in slightly acidic media. The proposed method has been applied successfully as a screening test for aluminium(III) ion in river water sampled at the downstream area of an old mine

Indium-bump-free antimonide superlattice membrane detectors on silicon substrates

Energy Technology Data Exchange (ETDEWEB)

Zamiri, M., E-mail: mzamiri@chtm.unm.edu, E-mail: skrishna@chtm.unm.edu; Klein, B.; Schuler-Sandy, T.; Dahiya, V.; Cavallo, F. [Center for High Technology Materials, Department of Electrical and Computer Engineering, University of New Mexico, Albuquerque, New Mexico 87106 (United States); Myers, S. [SKINfrared, LLC, Lobo Venture Lab, 801 University Blvd., Suite 10, Albuquerque, New Mexico 87106 (United States); Krishna, S., E-mail: mzamiri@chtm.unm.edu, E-mail: skrishna@chtm.unm.edu [Center for High Technology Materials, Department of Electrical and Computer Engineering, University of New Mexico, Albuquerque, New Mexico 87106 (United States); SKINfrared, LLC, Lobo Venture Lab, 801 University Blvd., Suite 10, Albuquerque, New Mexico 87106 (United States)

2016-02-29

We present an approach to realize antimonide superlattices on silicon substrates without using conventional Indium-bump hybridization. In this approach, PIN superlattices are grown on top of a 60 nm Al{sub 0.6}Ga{sub 0.4}Sb sacrificial layer on a GaSb host substrate. Following the growth, the individual pixels are transferred using our epitaxial-lift off technique, which consists of a wet-etch to undercut the pixels followed by a dry-stamp process to transfer the pixels to a silicon substrate prepared with a gold layer. Structural and optical characterization of the transferred pixels was done using an optical microscope, scanning electron microscopy, and photoluminescence. The interface between the transferred pixels and the new substrate was abrupt, and no significant degradation in the optical quality was observed. An Indium-bump-free membrane detector was then fabricated using this approach. Spectral response measurements provided a 100% cut-off wavelength of 4.3 μm at 77 K. The performance of the membrane detector was compared to a control detector on the as-grown substrate. The membrane detector was limited by surface leakage current. The proposed approach could pave the way for wafer-level integration of photonic detectors on silicon substrates, which could dramatically reduce the cost of these detectors.

A comparative study of the annealing behavior of Cu(In,Ga)(S,Se){sub 2} based solar cells with an indium sulfide buffer layer, partly submitted to wet chemical treatments

Energy Technology Data Exchange (ETDEWEB)

Hönes, C., E-mail: christian.hoenes@de.bosch.com [Corporate Research and Advance Engineering, Robert Bosch GmbH, Robert-Bosch-Straße 2, D-71701 Schwieberdingen (Germany); Laboratory for Photovoltaics, University of Luxembourg, 41 rue du Brill, L-4422 Belvaux (Luxembourg); Hackenberg, J. [Corporate Research and Advance Engineering, Robert Bosch GmbH, Robert-Bosch-Straße 2, D-71701 Schwieberdingen (Germany); Zweigart, S. [Corporate Research and Advance Engineering, Robert Bosch GmbH, Postfach 10 60 50, D-70049 Stuttgart (Germany); Wachau, A.; Hergert, F. [Bosch Solar CISTech GmbH, D-14772 Brandenburg (Germany); Siebentritt, S., E-mail: susanne.siebentritt@uni.lu [Laboratory for Photovoltaics, University of Luxembourg, 41 rue du Brill, L-4422 Belvaux (Luxembourg)

2015-03-07

Indium sulfide thin films deposited via thermal evaporation from compound source material have been successfully utilized as a cadmium free buffer layer for Cu(In,Ga)Se{sub 2} based solar cells. However, high efficiencies are only reached after an additional annealing step. In this work, the annealing behavior of Cu(In,Ga)(S,Se){sub 2} based indium sulfide buffered solar cells is compared to the annealing behavior of similar cells, which were submitted to wet chemical treatments partly containing cadmium ions. Upon annealing a significant improvement of the initial solar cell characteristics is observed for the untreated cell and is related to the increase of activation energy for the carrier recombination process and a decrease of the ideality factor within the one diode model. It is shown here that this improvement can also be achieved by wet treatments of the absorber prior to buffer layer deposition. Upon annealing these treated cells still gain in collection length but lose open circuit voltage, which is explained here within a model including a highly p-doped absorber surface layer and supported by simulations showing that a decrease in doping density of such a surface layer would lead to the observed effects.

Reduced thermal quenching in indium-rich self-organized InGaN/GaN quantum dots

KAUST Repository

Elafandy, Rami T.

2012-01-01

Differences in optical and structural properties of indium rich (27), indium gallium nitride (InGaN) self-organized quantum dots (QDs), with red wavelength emission, and the two dimensional underlying wetting layer (WL) are investigated. Temperature dependent micro-photoluminescence (?PL) reveals a decrease in thermal quenching of the QDs integrated intensity compared to that of the WL. This difference in behaviour is due to the 3-D localization of carriers within the QDs preventing them from thermalization to nearby traps causing an increase in the internal quantum efficiency of the device. Excitation power dependent ?PL shows a slower increase of the QDs PL signal compared to the WL PL which is believed to be due to the QDs saturation. © 2012 American Institute of Physics.

Rf reactive sputtering of indium-tin-oxide films

International Nuclear Information System (INIS)

Tvarozek, V.; Novotny, I.; Harman, R.; Kovac, J.

1986-01-01

Films of indium-tin-oxide (ITO) have been deposited by rf reactive diode sputtering of metallic InSn alloy targets, or ceramic ITO targets, in an Ar and Ar+0 2 atmosphere. Electrical as well as optical properties of ITO films were controlled by varying sputtering parameters and by post-deposition heat-treatment in Ar, H 2 , N 2 , H 2 +N 2 ambients. The ITO films exhibited low resistivity approx. 2 x 10 -4 Ω cm, high transmittance approx. 90% in the visible spectral region and high reflectance approx. 80% in the near infra-red region. (author)

Indium-111-labelled leucocytes for localisation of abscesses

Energy Technology Data Exchange (ETDEWEB)

Segal, A W; Thakur, M L; Arnot, R N; Lavender, J P [Royal Postgraduate Medical School, London (UK)

1976-11-13

Leucocytes from eight patients who were thought to have an abscess were labelled with indium-111 and reintroduced into the circulation. The distribution of radioactivity was followed by whole-body scanning and imaging with a gamma camera. Focal accumulations of radioactivity were observed in the lesion in the three patients with abscesses, in the lungs of a boy with bacterial endocarditis, in the knee of a woman with rheumatoid arthritis, and at the site of intramuscular injections in another patient. The use of radiolabelled cells for the detection of focal pathological processes would seem to be an important addition to conventional diagnostic methods.

Decomposition rates of radiopharmaceutical indium chelates in serum

International Nuclear Information System (INIS)

Yeh, S.M.; Meares, C.F.; Goodwin, D.A.

1979-01-01

The rates at which six small aminopolycarboxylate chelates of trivalent 111 In and three protein-bound chelates of 111 In deliver indium to the serum protein transferrin have been studied in sterile human serum at pH 7.3, 37 deg C. Sterically hindered chelates containing a substituent on an ethylene carbon of EDTA decompose with rates in the range 0.03 to 0.11% per day - one to two orders of magnitude slower than other chelates. Only small differences are observed between rates of decomposition for low-molecular-weight chelates and for protein-bound chelates having analogous structures. (author)

Indium antimonide based HEMT for RF applications

International Nuclear Information System (INIS)

Subash, T. D.; Gnanasekaran, T.

2014-01-01

We report on an indium antimonide high electron mobility transistor with record cut-off frequency characteristics. For high frequency response it is important to minimize parasitic resistance and capacitance to improve short-channel effects. For analog applications adequate pinch-off behavior is demonstrated. For proper device scaling we need high electron mobility and high electron density. Toward this end, the device design features and simulation are carried out by the Synopsys TCAD tool. A 30 nm InSb HEMT exhibits an excellent cut-off frequency of 586 GHz. To the knowledge of the authors, the obtained cut-off frequency is the highest ever reported in any FET on any material system. (semiconductor materials)

Development of a new surface ion-source and ion guide in the ALTO project

International Nuclear Information System (INIS)

Cuong, P.V.

2009-12-01

The present work is dedicated to the ALTO project which is the production of neutron-rich gallium isotopes by the ISOL thick-target technique using photo-fission and a surface ion source. We aim at the study of the structure of 82 Ge, 83 Ge, 84 Ge via the β decay of 82 Ga, 83 Ga, and 84 Ga. We focus on the development of a new surface ion source made from materials with a high work function φ which can give high ionisation efficiencies for elements with low ionisation potentials, like alkaline as well as gallium and indium. Tungsten, rhenium and iridium are considered as good candidates for a surface ionizer because the Saha-Langmuir equation indicates high surface ionisation efficiencies for these materials. This has motivated us to equip the surface ion source at ALTO with rhenium and iridium-coated rhenium ionizer tubes of the same dimensions as the surface ion source at ISOLDE. We performed a test experiment to measure the ionisation efficiency for gallium. We also built a simulation code for the ionisation efficiency of the different surface ionisation sources (different materials and dimensions). On the other hand, for future nuclear structure studies of refractory elements such as cobalt or nickel, the ISOL technique with a thick target is no longer suitable. Indeed, the high melting point of these elements makes it difficult to volatilize and release them from a thick target. For such a situation, a technique based on thin targets is needed and the laser ion guide based on a gas cell to slow down, neutralize and stop the recoiling nuclear reaction products combined with a laser beam to re-ionize them selectively, seems a good choice. A code based on the Geant-4 tool-kit has been built to simulate the ionisation of the buffer gas. In this work, we also briefly show the results of the photo-fission yield measurements at ALTO. The fission fragments were ionized in a hot plasma ion source, mass separated and detected by germanium and scintillator detectors

Surfactant effects of indium on cracking in AlN/GaN distributed Bragg reflectors grown via metal organic vapor phase epitaxy

Science.gov (United States)

Rodak, L. E.; Miller, C. M.; Korakakis, D.

2011-01-01

Aluminum Nitride (AlN) and Gallium Nitride (GaN) superlattice structures are often characterized by a network of cracks resulting from the large lattice mismatch and difference in thermal expansion coefficients, especially as the thickness of the layers increases. This work investigates the influence of indium as a surfactant on strain and cracking in AlN/GaN DBRs grown via Metal Organic Vapor Phase Epitaxy (MOVPE). DBRs with peak reflectivities ranging from 465 nm to 540 nm were grown and indium was introduced during the growth of the AlN layer. Image processing techniques were used to quantify the crack length per square millimeter and it was observed that indium has a significant effect on the crack formation and reduced the total crack length in these structures by a factor of two.

Standard specification for nuclear-grade silver-indium-cadmium alloy

CERN Document Server

American Society for Testing and Materials. Philadelphia

2003-01-01

1.1 This specification covers silver-indium-cadmium alloy for use as a control material in light-water nuclear reactors. 1.2 The scope of this specification excludes the use of this material in applications where material strength of this alloy is a prime requisite. Also, this material must be protected from the primary water by a corrosion and wear resistant cladding. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Optoelectronic and magnetic properties of Mn-doped indium tin oxide: A first-principles study

Science.gov (United States)

Nath Tripathi, Madhvendra; Saeed Bahramy, Mohammad; Shida, Kazuhito; Sahara, Ryoji; Mizuseki, Hiroshi; Kawazoe, Yoshiyuki

2012-10-01

The manganese doped indium tin oxide (ITO) has integrated magnetics, electronics, and optical properties for next generation multifunctional devices. Our first-principles density functional theory (DFT) calculations show that the manganese atom replaces b-site indium atom, located at the second coordination shell of the interstitial oxygen in ITO. It is also found that both anti-ferromagnetic and ferromagnetic behaviors are realizable. The calculated magnetic moment of 3.95μB/Mn as well as the high transmittance of ˜80% for a 150 nm thin film of Mn doped ITO is in good agreement with the experimental data. The inclusion of on-site Coulomb repulsion corrections via DFT + U methods turns out to improve the optical behavior of the system. The optical behaviors of this system reveal its suitability for the magneto-opto-electronic applications.

Beam-Loss Induced Pressure Rise of LHC Collimator Materials Irradiated with 158 GeV/u $In^{49+}$ Ions at the CERN SPS

CERN Document Server

Mahner, Edgar; Hansen, Jan; Page, Eric; Vincke, Helmut H

2004-01-01

During heavy ion operation, large pressure rises, up to a few orders of magnitude, were observed at CERN, GSI, and BNL. The dynamic pressure rises were triggered by lost beam ions that impacted onto the vacuum chamber walls and desorbed about 1044 to 107 molecules per ion. The deterioration of the dynamic vacuum conditions can enhance charge-exchange beam losses and can lead to beam instabilities or even to beam abortion triggered by vacuum interlocks. Consequently, a dedicated measure-ment of heavy-ion induced molecular desorption in the GeV/u energy range is important for LHC ion operation. In 2003, a desorption experiment was installed at the SPS to measure the beam-loss induced pressure rise of potential LHC collimator materials. Samples of bare graphite, sputter coated (Cu, TiZrV) graphite, and 316 LN stainless steel, were irradiated under grazing angle with 158 GeV/u indium ions. After a description of the new experimental set-up, the results of the pressure rise measurements are presented, and the deri...

Vibrational spectra of the cyanodimethylmetal complexes of magnesium, aluminium, gallium, and indium

International Nuclear Information System (INIS)

Mueller, J.; Schmock, F.; Klopsch, A.; Dehnicke, K.

1975-01-01

Tetramethylammonium cyanide reacts with an ethereal solution of dimethylmagnesium to form [NMe 4 ] 4 [Me 2 MgCN] 4 , the complex anion of which is isoelectronic with the known tetrameric dimethylaluminium cyanide [Me 2 AlCN] 4 . The vibrational spectra are reported together with those of the corresponding gallium and indium compounds. (orig.) [de

Recovery of galium and indium from liquid crystal displays and CIGS photovailtaic modules

NARCIS (Netherlands)

Bisselink, R.; Steeghs, W.; Brouwer, J.G.H.

2014-01-01

Abstract: The increasing amount of electronics, such as consumer products and green technologies (e.g. solar PV cells) increases the demand of metals such as indium and gallium. This increasing demand together with the dependency on import of these metals drive research on recycling of waste

Liver scanning using indium-113m at the University Teaching Hospital, Lusaka, Zambia

Energy Technology Data Exchange (ETDEWEB)

Mulaisho, C [Nuclear Medicine Unit, Department of Medicine, University of Zambia, Lusaka, Zambia; Mumba, K N [Radio-isotope Research Unit, National Council for Scientific Research, Lusaka, Zambia

1981-11-21

Liver scanning using the radio-isotope indium-113m, can now be routinely perfomed at the University Teaching Hospital, Lusaka, Zambia. The dose used is 1 - 4 mCi. Liver scans have been performed on 48 subjects, including 10 healthy individuals 16 patients with histologically proven hepatocellular carcinoma, 11 with clinical and laboratory evidence of portal hypertension and 11 with miscellaneous illnesses. Seven representative scans are illustrated. The procedure is easy, and gives a fairly accurate functional estimate of Kupffer cell mass. In hepatoma the scan may be either larger than or smaller than normal and reflects more accurately the residual function of the Kupffer cells. In cirrhosis of the liver with portal hypertention, residual Kupffer cell mass is small. Consequently, most of the indium-113m is taken up by the splenic reticulo-endothelial system, resulting in a large spleen scan. This technique, although fraught with major limitations, is a useful additional diagnostic tool in the management of chronic liver disease.

Synthesis of Two New Group 13 Benzoato-Chloro Complexes: A Structural Study of Gallium and Indium Chelating Carboxylates

Science.gov (United States)

Duraj, Stan A.; Hepp, Aloysius F.; Woloszynek, Robert; Protasiewicz, John D.; Dequeant, Michael; Ren, Tong

2010-01-01

Two new heteroleptic chelated-benzoato gallium (III) and indium (III) complexes have been prepared and structurally characterized. The molecular structures of [GaCl2(4-Mepy)2(O2CPh)]4-Mepy (1) and [InCl(4-Mepy)2(O2CPh)2]4-Mepy (2) have been determined by single-crystal x-ray diffraction. The gallium compound (1) is a distorted octahedron with cis-chloride ligands co-planar with the chelating benzoate and the 4-methylpyridines trans to each other. This is the first example of a Ga(III) structure with a chelating benzoate. The indium compound (2) is a distorted pentagonal bipyramid with two chelating benzoates, one 4-methylpyridine in the plane and a chloride trans to the other 4-methylpyridine. The indium bis-benzoate is an unusual example of a seven-coordinate structure with classical ligands. Both complexes, which due to the chelates, could also be described as pseudo-trigonal bipyramidal, include a three-bladed motif with three roughly parallel aromatic rings that along with a solvent of crystallization and electron-withdrawing chloride ligand(s) stabilize the solid-state structures.

Roentgenographic and derivatographic investigation of gallium and indium complexes with azo compounds on the base of pyrogallol

International Nuclear Information System (INIS)

Gambarov, D.G.; Rzaev, R.Z.; Musaev, F.N.; Musaeva, A.N.; Chyragov, F.M.

1985-01-01

Seven complexes of gallium and indium with N-donor ligands obtained on the base of pyrogallol are synthesized. Their chemical composition is established. Nitrogen-containing ligands and their complexes are investigated by the methods of roentgenographic and thermogravimetric analyses. It is shown that gallium and indium complexes are amorphous compounds. An assumption is made on the thermolysis character that complexes have a similar structure: structural complex nucleus constitutes a six-term chelate ring. Para-substitutors in the ligand do not participate in complexing, possibly they participate in H-bonds formation. It is established by spectrophotometric methods that in solutions stoichiometric ratio metal: ligand is the same as in the solid phase

Roentgenographic and derivatographic investigation of gallium and indium complexes with azo compounds on the base of pyrogallol

Energy Technology Data Exchange (ETDEWEB)

Gambarov, D G; Rzaev, R Z; Musaev, F N; Musaeva, A N; Chyragov, F M

1985-01-01

Seven complexes of gallium and indium with N-donor ligands obtained on the base of pyrogallol are synthesized. Their chemical composition is established. Nitrogen-containing ligands and their complexes are investigated by the methods of roentgenographic and thermogravimetric analyses. It is shown that gallium and indium complexes are amorphous compounds. An assumption is made on the thermolysis character that complexes have a similar structure: structural complex nucleus constitutes a six-term chelate ring. Para-substitutors in the ligand do not participate in complexing, possibly they participate in H-bonds formation. It is established by spectrophotometric methods that in solutions stoichiometric ratio metal: ligand is the same as in the solid phase.

Magnetron sputtered transparent conductive zinc-oxide stabilized amorphous indium oxide thin films on polyethylene terephthalate substrates at ambient temperature

International Nuclear Information System (INIS)

Yan, Y.; Zhang, X.-F.; Ding, Y.-T.

2013-01-01

Amorphous transparent conducting zinc-oxide stabilized indium oxide thin films, named amorphous indium zinc oxide (a-IZO), were deposited by direct current magnetron sputtering at ambient temperature on flexible polyethylene terephthalate substrates. It has been demonstrated that the electrical resistivity could attain as low as ∼ 5 × 10 −4 Ω cm, which was noticeably lower than amorphous indium tin oxide films prepared at the same condition, while the visible transmittance exceeded 84% with the refractive index of 1.85–2.00. In our experiments, introduction of oxygen gas appeared to be beneficial to the improvement of the transparency and electrical conductivity. Both free carrier absorption and indirect transition were observed and Burstein–Moss effect proved a-IZO to be a degenerated amorphous semiconductor. However, the linear relation between the optical band gap and the band tail width which usually observed in covalent amorphous semiconductor such as a-Si:H was not conserved. Besides, porosity could greatly determine the resistivity and optical constants for the thickness variation at this deposition condition. Furthermore, a broad photoluminescence peak around 510 nm was identified when more than 1.5 sccm oxygen was introduced. - Highlights: ► Highly conducting amorphous zinc-oxide stabilized indium oxide thin films were prepared. ► The films were fabricated on polyethylene terephthalate at ambient temperature. ► Introduction of oxygen can improve the transparency and electrical conductivity. ► The linear relation between optical band gap and band tail width was not conserved

Vacancy-acceptor complexes in germanium produced by ion implantation

Energy Technology Data Exchange (ETDEWEB)

Feuser, U.; Vianden, R. (Inst. fuer Strahlen- und Kernphysik, Univ. Bonn (Germany)); Alves, E.; Silva, M.F. da (Dept. de Fisica, ICEN/LNETI, Sacavem (Portugal)); Szilagyi, E.; Paszti, F. (Central Research Inst. for Physics, Hungarian Academy of Sciences, Budapest (Hungary)); Soares, J.C. (Centro de Fisica Nuclear, Univ. Lisbon (Portugal))

1991-07-01

Combining results obtained by the {gamma}-{gamma} perturbed angular correlation method, Rutherford backscattering and elastic recoil detection of hydrogen, a defect complex formed in germanium by indium implantation is identified as a vacancy trapped by the indium probe. (orig.).

Control of surface adatom kinetics for the growth of high-indium content InGaN throughout the miscibility gap

Science.gov (United States)

Moseley, Michael; Lowder, Jonathan; Billingsley, Daniel; Doolittle, W. Alan

2010-11-01

The surface kinetics of InGaN alloys grown via metal-modulated epitaxy (MME) are explored in combination with transient reflection high-energy electron diffraction intensities. A method for monitoring and controlling indium segregation in situ is demonstrated. It is found that indium segregation is more accurately associated with the quantity of excess adsorbed metal, rather than the metal-rich growth regime in general. A modified form of MME is developed in which the excess metal dose is managed via shuttered growth, and high-quality InGaN films throughout the miscibility gap are grown.

Control of surface adatom kinetics for the growth of high-indium content InGaN throughout the miscibility gap

International Nuclear Information System (INIS)

Moseley, Michael; Lowder, Jonathan; Billingsley, Daniel; Doolittle, W. Alan

2010-01-01

The surface kinetics of InGaN alloys grown via metal-modulated epitaxy (MME) are explored in combination with transient reflection high-energy electron diffraction intensities. A method for monitoring and controlling indium segregation in situ is demonstrated. It is found that indium segregation is more accurately associated with the quantity of excess adsorbed metal, rather than the metal-rich growth regime in general. A modified form of MME is developed in which the excess metal dose is managed via shuttered growth, and high-quality InGaN films throughout the miscibility gap are grown.

The new barium mercuride BaHg6 and ternary indium and gallium derivatives

International Nuclear Information System (INIS)

Wendorff, Marco; Röhr, Caroline

2013-01-01

Highlights: ► The new binary Hg-rich mercuride BaHg 6 crystallizes with a singular structure type. ► Ternary In substituted compounds are isotypic, whereas Ga substituted compounds are only structurally related. ► Structure relation to other Hg-rich alkali and alkaline earth mercurides. ► Discussion of covalent and metallic bonding aspects, as found by structure features and band structure calculations. - Abstract: The new binary barium mercuride BaHg 6 and the derived ternary indium and gallium containing compounds BaIn 1.2 Hg 4.8 and BaGa 0.8 Hg 5.2 were synthesized from melts of the elements, which were slowly cooled from 500 to 200 °C. Their crystal structures have been determined by means of single crystal X-ray diffraction. The binary mercuride BaHg 6 (Pnma, a = 1338.9(3), b = 519.39(13), c = 1042.6(4) pm, Z = 4, R1 = 0.0885) and the isotypic indium substituted compound BaIn 1.2 Hg 4.8 as well as the structurally related gallium mercuride BaGa 0.8 Hg 5.2 (Cmcm, a = 729.77(7), b = 1910.1(2), c = 507.48(5) pm, Z = 4, R1 = 0.0606) crystallize with new structure types. Common features of both structures are planar nets of five- and eight-membered Hg rings, stacked perpendicular to the shortest axes. According to their lengths, the Hg–Hg bonds can be classified into three groups: strong, short ones (I, 285–292 pm), which are only found inside the nets, and longer distances (II), still carrying bond critical points, around 300 pm. Further contacts (III) serve to complete the coordination spheres of Hg/M (320–358 pm). The overall coordination numbers of Hg/M range from 10 to 13. The Ba cations are positioned in the centers of the octagons of the Hg/M nets, thus exhibiting a 5:8:5, i.e. 18, coordination by Hg/M atoms. DFT calculations of the electronic band structure of pure BaHg 6 and ordered models of the indium ( ′ BaInHg 5 ′ ) and the gallium ( ′ BaGaHg 5 ′ ) mercurides were performed using the FP-LAPW method. The calculated Bader charges

High-performance a-IGZO thin-film transistor with conductive indium-tin-oxide buried layer

Science.gov (United States)

Ahn, Min-Ju; Cho, Won-Ju

2017-10-01

In this study, we fabricated top-contact top-gate (TCTG) structure of amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFTs) with a thin buried conductive indium-tin oxide (ITO) layer. The electrical performance of a-IGZO TFTs was improved by inserting an ITO buried layer under the IGZO channel. Also, the effect of the buried layer's length on the electrical characteristics of a-IGZO TFTs was investigated. The electrical performance of the transistors improved with increasing the buried layer's length: a large on/off current ratio of 1.1×107, a high field-effect mobility of 35.6 cm2/Vs, a small subthreshold slope of 116.1 mV/dec, and a low interface trap density of 4.2×1011 cm-2eV-1 were obtained. The buried layer a-IGZO TFTs exhibited enhanced transistor performance and excellent stability against the gate bias stress.

Indium-111-labelled leucocytes for localisation of abscesses

International Nuclear Information System (INIS)

Segal, A.W.; Thakur, M.L.; Arnot, R.N.; Lavender, J.P.

1976-01-01

Leucocytes from eight patients who were thought to have an abscess were labelled with indium-111 and reintroduced into the circulation. The distribution of radioactivity was followed by whole-body scanning and imaging with a gamma camera. Focal accumulations of radioactivity were observed in the lesion in the three patients with abscesses, in the lungs of a boy with bacterial endocarditis, in the knee of a woman with rheumatoid arthritis, and at the site of intramuscular injections in another patient. The use of radiolabelled cells for the detection of focal pathological processes would seem to be an important addition to conventional diagnostic methods. (author)

Enhancement of indium incorporation to InGaN MQWs on AlN/GaN periodic multilayers

Science.gov (United States)

Monavarian, Morteza; Hafiz, Shopan; Das, Saikat; Izyumskaya, Natalia; Özgür, Ümit; Morkoç, Hadis; Avrutin, Vitaliy

2016-02-01

The effect of compressive strain in buffer layer on strain relaxation and indium incorporation in InGaN multi-quantum wells (MQWs) is studied for two sets of samples grown side by side on both relaxed GaN layers and strained 10-pairs of AlN/GaN periodic multilayers. The 14-nm AlN layers were utilized in both multilayers, while GaN thickness was 4.5 and 2.5 nm in the first and the second set, respectively. The obtained results for the InGaN active layers on relaxed GaN and AlN/GaN periodic multilayers indicate enhanced indium incorporation for more relaxed InGaN active layers providing a variety of emission colors from purple to green.

Structural, electronic, and thermal properties of indium-filled InxIr4Sb12 skutterudites

Science.gov (United States)

Wallace, M. K.; Li, Jun; Subramanian, M. A.

2018-06-01

The "phonon-glass/electron-crystal" approach has been implemented through incorporation of "rattlers" into skutterudite void sites to increase phonon scattering and thus increase the thermoelectric efficiency. Indium filled IrSb3 skutterudites are reported for the first time. Polycrystalline samples of InxIr4Sb12 (0 ≤ x ≤ 0.2) were prepared by solid-state reaction under a gas mixture of 5% H2 and 95% Ar. The solubility limit of InxIr4Sb12 was found to be close to 0.18. Synchrotron X-ray diffraction refinements reveal all InxIr4Sb12 phases crystallized in body-centered cubic structure (space group : Im 3 bar) with ∼8% antimony site vacancy and with indium partially occupying the 16f site. Unlike known rattler filled skutterudites, under synthetic conditions employed, indium filling in IrSb3 significantly increases the electrical resistivity and decreases the Seebeck coefficient (n-type) while reducing the thermal conductivity by ∼30%. The resultant power factor offsets the decrease in total thermal conductivity giving rise to a substantial decrease in ZT. Principal thermoelectric properties of InxM4Sb12 (M = Co, Rh, Ir) phases are compared. As iridium is a 5d transition metal, zero field cooled (ZFC) magnetization were performed to unravel the effect of spin-orbit interaction on the electronic properties. These results serve to advance the understanding of filled skutterudites, and provide additional insight on the less explored smaller "rattlers" and their influence on key thermoelectric properties.

Metal-organic chemical vapor deposition of high quality, high indium composition N-polar InGaN layers for tunnel devices

Science.gov (United States)

Lund, Cory; Romanczyk, Brian; Catalano, Massimo; Wang, Qingxiao; Li, Wenjun; DiGiovanni, Domenic; Kim, Moon J.; Fay, Patrick; Nakamura, Shuji; DenBaars, Steven P.; Mishra, Umesh K.; Keller, Stacia

2017-05-01

In this study, the growth of high quality N-polar InGaN films by metalorganic chemical vapor deposition is presented with a focus on growth process optimization for high indium compositions and the structural and tunneling properties of such films. Uniform InGaN/GaN multiple quantum well stacks with indium compositions up to 0.46 were grown with local compositional analysis performed by energy-dispersive X-ray spectroscopy within a scanning transmission electron microscope. Bright room-temperature photoluminescence up to 600 nm was observed for films with indium compositions up to 0.35. To study the tunneling behavior of the InGaN layers, N-polar GaN/In0.35Ga0.65N/GaN tunnel diodes were fabricated which reached a maximum current density of 1.7 kA/cm2 at 5 V reverse bias. Temperature-dependent measurements are presented and confirm tunneling behavior under reverse bias.

Epitaxy-enabled vapor-liquid-solid growth of tin-doped indium oxide nanowires with controlled orientations

KAUST Repository

Shen, Youde; Turner, Stuart G.; Yang, Ping; Van Tendeloo, Gustaaf; Lebedev, Oleg I.; Wu, Tao

2014-01-01

challenges in reliably achieving these goals of orientation-controlled nanowire synthesis and assembly. Here we report that growth of planar, vertical and randomly oriented tin-doped indium oxide (ITO) nanowires can be realized on yttria-stabilized zirconia

Seasonal variability in the input of lead, barium and indium to Law Dome, Antarctica

DEFF Research Database (Denmark)

Burn-Nunes...[], L.J.; Vallelonga, Paul Travis; Loss, R.D.

2011-01-01

Lead (Pb) isotopic compositions and concentrations, and barium (Ba) and indium (In) concentrations have been determined at monthly resolution in five Law Dome (coastal Eastern Antarctica) ice core sections dated from similar to 1757 AD to similar to 1898 AD. 'Natural' background Pb concentrations...

Value Recovery from Waste Liquid Crystal Display Glass Cullet through Leaching: Understanding the Correlation between Indium Leaching Behavior and Cullet Piece Size

OpenAIRE

Basudev Swain; Chan Gi Lee; Hyun Seon Hong

2018-01-01

For hydrometallurgical recovery of indium from glass cullet after dismantling a waste liquid crystal display (LCD), leaching is the rudimentary stage. Though size reduction of the cullet pieces adds convenience for recycling, from an efficiency and cost-effectiveness perspective regarding leaching process development, determining the proper cullet piece size is essential. Hence, in this study, leaching efficiency of indium as a function of cullet piece size was investigated, wherein the prope...

Investigation of space-occupying lesions in the liver with technetium-99m tin colloid and indium-113m-chloride

International Nuclear Information System (INIS)

Nelson, M.J.; Klopper, J.F.

1985-01-01

Liver scanning with radiocolloids is an important method to determine the presence, the position and the size of space-occupying lesions in the liver. Unfortunately, this information is nonspecific and it is not possible to distinguish between tumours, abscesses or cysts. Thirty-six patients in whom a definite diagnosis of hepatoma, amoebic liver abscess or echinococcus cyst had been made were examined with technetium-99m tin colloid and indium-113m chloride. The amoebic liver abscesses were avascular, showed a hyperaemic area surrounding the abscess and appeared smaller on the indium than on the technetium scan. The hepatomas showed greater vascularity and absence of the hyperaemic area. Cysts were avascular, did not show a hyperaemic rim and the size was equal on both scans. The experience of the observers had an influence on the accuracy of interpretation of the scans; experienced observers made a correct diagnosis in 73% of cases. It is suggested that simultaneous technetium-99m tin colloid and indium 113m-chloride scans provide additional specificity in the differential diagnosis between hepatoma, amoebic liver abscess and echinococcus cysts

Investigation of space-occupying lesions in the liver with technetium-99m tin colloid and indium-113m-chloride

Energy Technology Data Exchange (ETDEWEB)

Nelson, M.J. (Provincial Hospital, Port Elizabeth (South Africa). Dept. of Nuclear Medicine); Klopper, J.F. (Stellenbosch Univ. (South Africa). Dept. of Nuclear Medicine)

1985-01-26

Liver scanning with radiocolloids is an important method to determine the presence, the position and the size of space-occupying lesions in the liver. Unfortunately, this information is nonspecific and it is not possible to distinguish between tumours, abscesses or cysts. Thirty-six patients in whom a definite diagnosis of hepatoma, amoebic liver abscess or echinococcus cyst had been made were examined with technetium-99m tin colloid and indium-113m chloride. The amoebic liver abscesses were avascular, showed a hyperaemic area surrounding the abscess and appeared smaller on the indium than on the technetium scan. The hepatomas showed greater vascularity and absence of the hyperaemic area. Cysts were avascular, did not show a hyperaemic rim and the size was equal on both scans. The experience of the observers had an influence on the accuracy of interpretation of the scans; experienced observers made a correct diagnosis in 73% of cases. It is suggested that simultaneous technetium-99m tin colloid and indium 113m-chloride scans provide additional specificity in the differential diagnosis between hepatoma, amoebic liver abscess and echinococcus cysts.

Complexing of indium and thallium with 4-methyl-2-and 4-adamantyl-2-(2'-hydroxynaphthylazo-1')-thiazole

International Nuclear Information System (INIS)

Pilipenko, A.T.; Karetnikova, E.A.

1982-01-01

Complexing of indium with 4-methyl-2-(2'-oxynaphtylazo-1')-thiazol is studied. The optimal region of In complexing is pH 3.5-5.0. Component ratio in the complex is 1:1. The optimal conditions for extracting the formed complexes by chloroform, the spectrophotometric characteristics of the complexes and stability constants are determined. The determination of In with reagent should be conducted in aqueous-alcohol medium at a 5-fold excess of the reactant. At a 1 cm thickness of the absorbing layer the sensitivity of determination makes up 0.024. Phosphate, EDTA, citrate, oxalate, tartrate interfere with the determination of In. A technique for the determination of indium impurities in alkali-halogen crystals is developed

Calibration of the indium foil used for criticality accident dosimetry in the UCC-ND employee identification badge

International Nuclear Information System (INIS)

Ryan, M.T.; Butler, H.M.; Gupton, E.D.; Sims, C.S.

1982-05-01

The UCC-ND Employee Identification Badge contains an indium foil disc that is intended for use as a dosimetry screening device in the event of a criticality accident. While it is recognized that indium is not a precise mixed neutron-gamma dosimeter, its activation by neutrons provides adequate means for separating potentially exposed persons into three groups. These groups are: (1) personnel exposed below annual dose limits, (2) personnel exposed above annual dose limits but below 25 rem, and (3) personnel exposed above 25 rem. This screening procedure is designed to facilitate dosimeter processing in order to meet regulatory reporting requirements. A quick method of interpreting induced activity measurements is presented and discussed

Optimisation of chemical solution deposition of indium tin oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Sunde, Tor Olav Løveng; Einarsrud, Mari-Ann; Grande, Tor, E-mail: grande@ntnu.no

2014-12-31

An environmentally friendly aqueous sol–gel process has been optimised to deposit indium tin oxide (ITO) thin films, aiming to improve the film properties and reduce the deposition costs. It was demonstrated how parameters such as cation concentration and viscosity could be applied to modify the physical properties of the sol and thereby reduce the need for multiple coatings to yield films with sufficient conductivity. The conductivity of the thin films was enhanced by adjusting the heat treatment temperature and atmosphere. Both increasing the heat treatment temperature of the films from 530 to 800 °C and annealing in reducing atmosphere significantly improved the electrical conductivity, and conductivities close to the state of the art sputtered ITO films were obtained. A pronounced decreased conductivity was observed after exposing the thin films to air and the thermal reduction and ageing of the film was studied by in situ conductivity measurements. - Highlights: • Spin coating of indium tin oxide using an aqueous solution was optimised. • The conductivity was enhanced by thermal annealing in reducing atmosphere. • The conductivity of is comparable to the conductivity of sputtered films. • A relaxation process in the reduced thin film was observed after exposure in air.

Optical properties of indium nitride films

International Nuclear Information System (INIS)

Tyagaj, V.A.; Evstigneev, A.M.; Krasiko, A.N.; Andreeva, A.F.; Malakhov, V.Ya.

1977-01-01

Reflection and transmission spectra of heavily doped indium nitride are studied at lambda=0.5-5 μm. Dispersion of the refractive index near the plasma resonance frequency, h.f. dielectric constant (epsilonsub(infinity)=9.3), and extinction coefficient near the transmission maximum of films have been determined from the analysis of interference pattern. The reflection spectrum exhibits maximum in the infrared range and optical effective mass is found through its position (msub(opt)*=0.11msub(0)). Free carrier absorption coefficient is shown to vary according to the law K approximately lambdasup(2.9+-0.1) which is characteristic of electron scattering by charged impurities. The analysis of absorption spectra near the threshold of interband transitions has lead to the conclusion that free carriers are localized in the lateral extremum of conduction band (or out of the center of the Brillouin zone), therefore the Burstein-Moss effect is absent

Effect of replacement of tin doped indium oxide (ITO) by ZnO: analysis of environmental impact categories

Science.gov (United States)

Ziemińska-Stolarska, Aleksandra; Barecka, Magda; Zbiciński, Ireneusz

2017-10-01

Abundant use of natural resources is doubtlessly one of the greatest challenges of sustainable development. Process alternatives, which enable sustainable manufacturing of valuable products from more accessible resources, are consequently required. One of examples of limited resources is Indium, currently broadly used for tin doped indium oxide (ITO) for production of transparent conductive films (TCO) in electronics industry. Therefore, candidates for Indium replacement, which would offer as good performance as the industrial state-of-the-art technology based on ITO are widely studied. However, the environmental impact of new layers remains unknown. Hence, this paper studies the environmental effect of ITO replacement by zinc oxide (ZnO) by means life cycle assessment (LCA) methodology. The analysis enables to quantify the environmental impact over the entire period of life cycle of products—during manufacturing, use phase and waste generation. The analysis was based on experimental data for deposition process. Further, analysis of different impact categories was performed in order to determine specific environmental effects related to technology change. What results from the analysis, is that ZnO is a robust alternative material for ITO replacement regarding environmental load and energy efficiency of deposition process which is also crucial for sustainable TCO layer production.

Photoconductivity in reactively evaporated copper indium selenide thin films

Science.gov (United States)

Urmila, K. S.; Asokan, T. Namitha; Pradeep, B.; Jacob, Rajani; Philip, Rachel Reena

2014-01-01

Copper indium selenide thin films of composition CuInSe2 with thickness of the order of 130 nm are deposited on glass substrate at a temperature of 423 ±5 K and pressure of 10-5 mbar using reactive evaporation, a variant of Gunther's three temperature method with high purity Copper (99.999%), Indium (99.999%) and Selenium (99.99%) as the elemental starting materials. X-ray diffraction (XRD) studies shows that the films are polycrystalline in nature having preferred orientation of grains along the (112) plane. The structural type of the film is found to be tetragonal with particle size of the order of 32 nm. The structural parameters such as lattice constant, particle size, dislocation density, number of crystallites per unit area and strain in the film are also evaluated. The surface morphology of CuInSe2 films are studied using 2D and 3D atomic force microscopy to estimate the grain size and surface roughness respectively. Analysis of the absorption spectrum of the film recorded using UV-Vis-NIR Spectrophotometer in the wavelength range from 2500 nm to cutoff revealed that the film possess a direct allowed transition with a band gap of 1.05 eV and a high value of absorption coefficient (α) of 106 cm-1 at 570 nm. Photoconductivity at room temperature is measured after illuminating the film with an FSH lamp (82 V, 300 W). Optical absorption studies in conjunction with the good photoconductivity of the prepared p-type CuInSe2 thin films indicate its suitability in photovoltaic applications.

Faceted titania nanocrystals doped with indium oxide nanoclusters as a superior candidate for sacrificial hydrogen evolution without any noble-metal cocatalyst under solar irradiation.

Science.gov (United States)

Amoli, Vipin; Sibi, Malayil Gopalan; Banerjee, Biplab; Anand, Mohit; Maurya, Abhayankar; Farooqui, Saleem Akhtar; Bhaumik, Asim; Sinha, Anil Kumar

2015-01-14

Development of unique nanoheterostructures consisting of indium oxide nanoclusters like species doped on the TiO2 nanocrystals surfaces with {101} and {001} exposed facets, resulted in unprecedented sacrificial hydrogen production (5.3 mmol h(-1) g(-1)) from water using methanol as a sacrificial agent, under visible light LED source and AM 1.5G solar simulator (10.3 mmol h(-1) g(-1)), which is the highest H2 production rate ever reported for titania based photocatalysts, without using any noble metal cocatalyst. X-ray photoelectron spectroscopy (XPS) analysis of the nanostructures reveals the presence of Ti-O-In and In-O-In like species on the surface of nanostructures. Electron energy-loss spectroscopy (EELS) elemental mapping and EDX spectroscopy techniques combined with transmission electron microscope evidenced the existence of nanoheterostructures. XPS, EELS, EDX, and HAADF-STEM tools collectively suggest the presence of indium oxide nanoclusters like species on the surface of TiO2 nanostructures. These indium oxide nanocluster doped TiO2 (In2O3/T{001}) single crystals with {101} and {001} exposed facets exhibited 1.3 times higher visible light photocatalytic H2 production than indium oxide nanocluster doped TiO2 nanocrystals with only {101}facets (In2O3/T{101}) exposed. The remarkable photocatalytic activity of the obtained nanoheterostructures is attributed to the combined synergetic effect of indium oxide nanoclusters interacting with the titania surface, enhanced visible light response, high crystallinity, and unique structural features.

Indium vacancy induced d0 ferromagnetism in Li-doped In2O3 nanoparticles

Science.gov (United States)

Cao, Haiming; Xing, Pengfei; Zhou, Wei; Yao, Dongsheng; Wu, Ping

2018-04-01

Li-doped In2O3 nanoparticles with room temperature d0 ferromagnetism were prepared by a sol-gel method. X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence were carried out to investigate the effects of Li incorporation on the lattice defects. As the content of Li increases, non-monotonic changes in shifts of XRD peak (2 2 2) and the intensity ratios of indium vacancies related photoluminescence peak (PII) with respect to oxygen vacancies related peak (PI) are observed. Results show that at low doping level (≤2 at.%) Li prefers to occupy In sites, while with further doping the interstitial sites are more favorable for Li. Combined with the consistent non-monotonic change in saturation magnetization, we think that indium vacancies resulting from Li-doping play an important role in inducing d0 ferromagnetism in our Li-doped In2O3 nanoparticles, and the FM coupling is mainly mediated by the LiIn-ONN-VIn-ONN-LiIn chains.

Synthesis of Chromane Derivatives via Indium-mediated Intramolecular Allenylation and Allylation to Imines

International Nuclear Information System (INIS)

Kang, Han Young; Yu, Yeon Kwon

2004-01-01

The results of preparing chromans by intramolecular allylation are shown in Table 2. The results indicated that the indium-mediated allylation was not as efficient as the allenylation. About 10-20% decrease in yields was observed. As mentioned above, in each case only a single isomer was observed, and the stereochemistry of the product was determined as cis by analysis of 1 H NMR and NOE spectra. There are, however, still some limitations in these transformations. Especially, in the case of allylation mixtures of cis and trans isomers are always produced in about 2 : 1 ratio (cis/trans). The ratio was not improved under the various reaction conditions we attempted. Since the indium-mediated addition to carbonyl groups has been successful, it occurred to us that it would be worthwhile to test the addition to carbon-nitrogen double bonds, that is, imine groups. We wish to report here the results of the investigations on allylation and allenylation to C=N bond to provide the chromane structures. The whole transformations

Crack density and electrical resistance in indium-tin-oxide/polymer thin films under cyclic loading

KAUST Repository

Mora Cordova, Angel; Khan, Kamran; El Sayed, Tamer

2014-01-01

Here, we propose a damage model that describes the degradation of the material properties of indium-tin-oxide (ITO) thin films deposited on polymer substrates under cyclic loading. We base this model on our earlier tensile test model and show

Research on structure and electrical parameters of indium antimonide films

International Nuclear Information System (INIS)

Mukhametniyazova, A.; Konyaeva, V.F.; Sukhanov, S.; Ashirov, A.; Aleksanyan, S.N.

1980-01-01

Results of investigations into the effect of conditions of formation of indium antimonide films prepared by thermal vacuum spraying on their structure, phase composition and electric parameters, are presented. The method of studying the synthesized semiconductor layers on the DRON-0.5 X-ray device with CoKsub(α)-radiation is tested. The dependence of structure, phase composition and electric properties of InSb layers 1+3 μm thick sprayed on ferrite substrates on condensation temperature, is established. Hexagonal InSb modification is found

Research on structure and electrical parameters of indium antimonide films

Energy Technology Data Exchange (ETDEWEB)

Mukhametniyazova, A; Konyaeva, V F; Sukhanov, S; Ashirov, A; Aleksanyan, S N [AN Turkmenskoj SSR, Ashkhabad. Fiziko-Tekhnicheskii Inst.

1980-01-01

Results of investigations into the effect of conditions of formation of indium antimonide films prepared by thermal vacuum spraying on their structure, phase composition and electric parameters, are presented. The method of studying the synthesized semiconductor layers on the DRON-0.5 X-ray device with CoKsub(..cap alpha..)-radiation is tested. The dependence of structure, phase composition and electric properties of InSb layers 1+3 ..mu..m thick sprayed on ferrite substrates on condensation temperature, is established. Hexagonal InSb modification is found.

Structure, stability and electrochromic properties of polyaniline film covalently bonded to indium tin oxide substrate

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wenzhi, E-mail: zhangwz@xatu.edu.cn [Key Laboratory for Photoelectric Functional Materials and Devices of Shaanxi Province, School of Materials and Chemical Engineering, Xi’an Technological University, Xi’an 710021 (China); Ju, Wenxing; Wu, Xinming; Wang, Yan; Wang, Qiguan; Zhou, Hongwei; Wang, Sumin [Key Laboratory for Photoelectric Functional Materials and Devices of Shaanxi Province, School of Materials and Chemical Engineering, Xi’an Technological University, Xi’an 710021 (China); Hu, Chenglong [Key Laboratory of Optoelectronic Chemical Materials and Devices of Ministry of Education, School of Chemistry and Environmental Engineering, Jianghan University, Wuhan 430056 (China)

2016-03-30

Graphical abstract: A chemical bonding approach was proposed to prepare the PANI film covalently bonded to ITO substrate and the film exhibited high electrochemical activities and stability compared with that obtained by conventional film-forming approach. - Highlights: • The PANI film covalently bonded to ITO substrate was prepared using ABPA as modifier. • The oxidative potentials of the obtained PANI film were decreased. • The obtained PANI film exhibits high electrochemical activities and stability. - Abstract: Indium tin oxide (ITO) substrate was modified with 4-aminobenzylphosphonic acid (ABPA), and then the polyaniline (PANI) film covalently bonded to ITO substrate was prepared by the chemical oxidation polymerization. X-ray photoelectron spectroscopy (XPS), attenuated total reflection infrared (ATR-IR) spectroscopy, and atomic force microscopy (AFM) measurements demonstrated that chemical binding was formed between PANI and ABPA-modified ITO surface, and the maximum thickness of PANI layer is about 30 nm. The adhesive strength of PANI film on ITO substrate was tested by sonication. It was found that the film formed on the modified ITO exhibited a much better stability than that on bare one. Cyclic voltammetry (CV) and UV–vis spectroscopy measurements indicated that the oxidative potentials of PANI film on ABPA-modified ITO substrate were decreased and the film exhibited high electrochemical activities. Moreover, the optical contrast increased from 0.58 for PANI film (without ultrasound) to 1.06 for PANI film (after ultrasound for 60 min), which had an over 83% enhancement. The coloration time was 20.8 s, while the bleaching time was 19.5 s. The increase of electrochromic switching time was due to the lower ion diffusion coefficient of the large cation of (C{sub 4}H{sub 9}){sub 4}N{sup +} under the positive and negative potentials as comparison with the small Li{sup +} ion.

Synthesis, characterization, and bonding of indium cluster phases: Na15In27.4, a network of In16 and In11 clusters; Na2In with isolated indium tetrahedra

International Nuclear Information System (INIS)

Sevov, S.C.; Corbett, J.D.

1993-01-01

The remaining phases in the Na-In system have been identified and characterized. The indium-richest is Na 15 In 27.4 , with a structure containing novel closo-In 16 clusters interconnected to two kinds of nido-In 11 units and isolated, 4-bonded atoms (Cmcm, Z = 8, a = 16.108 (4) Angstrom, b = 35.279 (8) Angstrom, c = 15.931 (3) Angstrom, R/R w = 0.041/0.044 at the indium-rich limits Na 15 In 27.54 ). Fractional occupancy of two atoms in cluster chain positions were found, one as a function of a narrow nonstoichiometry. The structure is related to that recently established for Na 7 In 11.8 . Resistivity and magnetic properties are consistent with a small (0.5-3.2%) excess of electrons relative to the calculated bonding requirements. The sodium-richest phase is the stable, diamagnetic, and weakly metallic Na 2 In, isostructural with Na 2 Tl (C222 1 , Z = 16, a = 13.855 (1) Angstrom, b = 8.836 (1) Angstrom, c = 11.762 (1) Angstrom, R/R w = 0.030/0.034). A corrected phase diagram is given. 21 refs., 5 figs., 5 tabs

Preparation of lithium indium oxide via a rheological phase route and its electrochemical characteristics in LiOH and Li{sub 2}SO{sub 4} solutions

Energy Technology Data Exchange (ETDEWEB)

Zhang, Guo-Qing [Department of Chemistry and Environment Science of Yangtze Normal University, 408100 Chongqing (China); College of Chemistry and Chemical Engineering of Chongqing University, Chongqing 400030 (China); Zhang, Sheng-Tao [College of Chemistry and Chemical Engineering of Chongqing University, Chongqing 400030 (China); Wu, Xing-Fa [Department of Chemistry and Environment Science of Yangtze Normal University, 408100 Chongqing (China)

2010-01-15

Submicrometer-sized lithium indium oxide (LiInO{sub 2}) powder via a rheological phase method using trilithium citrate tetra hydrate (C{sub 6}H{sub 5}Li{sub 3}O{sub 7} . 4H{sub 2}O) and indium oxide (In{sub 2}O{sub 3}) has been prepared in this work for the first time. The optimal pyrolyzing temperature range to prepare crystalline LiInO{sub 2} is between 650 and 900 C, which was confirmed by thermal gravimetric and differential thermogravimetric analysis of the precursor and X-ray diffraction analysis. The pure phase LiInO{sub 2} sample obtained has a uniform particle morphology and submicrosize, which was observed by scanning electron microscopy. The electrochemical studies show that a new pair of cathodic and anodic peaks at 0.23 and 0.38 V (vs. saturated calomel electrode) was obviously observed from the cyclic voltammetry curve of LiInO{sub 2} in 1 M LiOH solution, indicating a battery characteristic of the material in this electrolyte. While in 1 M Li{sub 2}SO{sub 4} solution, the sample presents a supercapacitive characteristic within the same potential range. The reasons for different electrochemical behaviors in these two electrolytes can be attributed to the fact that the reaction of lithium ion insertion/extraction into/out of a LiInO{sub 2} electrode takes place in the bulk material in LiOH electrolyte solution, whereas it takes place on the electrode/electrolyte interface for Li{sub 2}SO{sub 4} electrolyte case. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Electrical, optical and photoelectric properties of cadmium sulfide monocrystals doped by indium and irradiated by electrons

CERN Document Server

Davidyuk, G E; Manzhara, V S

2002-01-01

One studied effect of irradiation by E = 1.2 MeV energy and PHI = 2 x 10 sup 1 sup 7 cm sup - sup 2 dose fast electrons on electrical, optical and photoelectrical CdS single-crystals doped by In. On the basis of analysis of the experimental results one makes conclusions about decomposition and, in this case, indium atoms occurring in cation sublattice nodes are knocked out by cadmium atoms. In CdS:In irradiated specimens one detected new centres of slow recombination with occurrence of maximums of photoconductivity optical suppression within lambda sub M sub sub 1 = 0.75 mu m and lambda sub M sub sub 2 = 1.03 mu m range. It is assumed that complexes containing cadmium vacancies and indium atoms are responsible for recombination new centres

The measurement of the amplitude of de Haas-van Alphen oscillations in indium

International Nuclear Information System (INIS)

Wilde, J. de; Meredith, D.J.

1976-01-01

A flux-gate magnetometer incorporating a superconducting flux transformer is described and its application to the measurement of de Haas-van Alphen oscillation amplitude is compared with conventional techniques. Measurements on the third zone Fermi surface of indium in magnetic fields of up to 4 T are given to show the advantages of the method. (author)

A novel 3D framework indium phosphite-oxalate based on a pcu-type topology

International Nuclear Information System (INIS)

Zuo, Mengmeng; Zhou, Mingdong; Hu, Dianwen; Gao, Fan; Dong, Sijie; Huang, Liangliang

2016-01-01

A new inorganic–organic hybrid indium phosphite-oxalate, formulated as H[In 5 (HPO 3 ) 6 (H 2 PO 3 ) 2 (C 2 O 4 ) 2 ]·(C 4 N 2 H 11 ) 2 ·H 2 O 1 has been hydrothermally synthesized in the presence of piperazine acting as a structure directing agent (SDA). The single crystal X-ray diffraction reveals that compound 1 shows three-dimensional open-framework with intersecting 12-ring channels along the [010] and [001] directions, which is constructed from strictly alternating double 6-ring units (D6Rs), [C 2 O 4 ] 2− groups and [H 2 PO 3 ] − pseudo-pyramids. It is noted that the classical D6R SBU is firstly reported in main metal phosphite/phosphite-oxalate. By regarding D6R as the 6-connected nodes, the inorganic–organic hybrid framework is based on a pcu-type topology. The as-synthesized product was characterized by single-crystal X-ray diffraction, powder X-ray diffraction, IR spectroscopy, thermogravimetric analysis (TGA), ICP-AES and elemental analyses. - Graphical abstract: A 3D open-framework indium phosphite-oxalate has been synthesized under hydrothermal conditions. A classical SBU, D6R, is present in the structure. By regarding D6R as the 6-connected nodes, the inorganic–organic hybrid framework is based on a pcu-type topology. - Highlights: • A new indium phosphite-oxalate based on a pcu-type topology has been synthesized. • A classical SBU, D6R, is present in the structure. • The classical SBU is firstly reported in main metal phosphite/phosphite-oxalate.

Effect of Temperature on Nucleation of Nanocrystalline Indium Tin Oxide Synthesized by Electron-Beam Evaporation

Science.gov (United States)

Shen, Yan; Zhao, Yujun; Shen, Jianxing; Xu, Xiangang

2017-07-01

Indium tin oxide (ITO) has been widely applied as a transparent conductive layer and optical window in light-emitting diodes, solar cells, and touch screens. In this paper, crystalline nano-sized ITO dendrites are obtained using an electron-beam evaporation technique. The surface morphology of the obtained ITO was studied for substrate temperatures of 25°C, 130°C, 180°C, and 300°C. Nano-sized crystalline dendrites were synthesized only at a substrate temperature of 300°C. The dendrites had a cubic structure, confirmed by the results of x-ray diffraction and transmission electron microscopy. The growth mechanism of the nano-crystalline dendrites could be explained by a vapor-liquid-solid (VLS) growth model. The catalysts of the VLS process were indium and tin droplets, confirmed by varying the substrate temperature, which further influenced the nucleation of the ITO dendrites.

Intramolecular charge separation in spirobifluorene-based donor–acceptor compounds adsorbed on Au and indium tin oxide electrodes

International Nuclear Information System (INIS)

Heredia, Daniel; Otero, Luis; Gervaldo, Miguel; Fungo, Fernando; Dittrich, Thomas; Lin, Chih-Yen; Chi, Liang-Chen; Fang, Fu-Chuan; Wong, Ken-Tsung

2013-01-01

Surface photovoltage (SPV) measurements were performed with a Kelvin-probe in spirobifluorene-based donor (diphenylamine)–acceptor (dicyano or cyanoacrylic acid moieties) compounds adsorbed from highly diluted solutions onto Au and indium tin oxide electrode surfaces. Strong intramolecular charge separation (negative SPV signals up to more than 0.1 V) due to directed molecule adsorption was observed only for spirobifluorene donor–acceptor compounds with carboxylic acid moiety. SPV signals and onset energies of electronic transitions depended on ambience conditions. - Highlights: ► Fluorene donor–acceptor derivatives were adsorbed at Au and indium tin oxide. ► Surface photovoltage measurements were performed with a Kelvin-probe. ► Strong intra-molecular charge separation was observed. ► SPV signals depended on ambience conditions

Beam-loss induced pressure rise of Large Hadron Collider collimator materials irradiated with 158 GeV/u $In^{49+}$ ions at the CERN Super Proton Synchrotron

CERN Document Server

Mahner, Edgar; Hansen, Jan; Page, Eric; Vincke, H

2004-01-01

During heavy ion operation, large pressure rises, up to a few orders of magnitude, were observed at CERN, GSI, and BNL. The dynamic pressure rises were triggered by lost beam ions that impacted onto the vacuum chamber walls and desorbed about 10/sup 4/ to 10/sup 7/ molecules per ion. The deterioration of the dynamic vacuum conditions can enhance charge-exchange beam losses and can lead to beam instabilities or even to beam abortion triggered by vacuum interlocks. Consequently, a dedicated measurement of heavy-ion induced molecular desorption in the GeV/u energy range is important for Large Hadron Collider (LHC) ion operation. In 2003, a desorption experiment was installed at the super proton synchrotron to measure the beam-loss induced pressure rise of potential LHC collimator materials. Samples of bare graphite, sputter coated (Cu, TiZrV) graphite, and 316 LN (low carbon with nitrogen) stainless steel were irradiated under grazing angle with 158 GeV/u indium ions. After a description of the new experimental ...

Enhancement of the electrical characteristics of thin-film transistors with indium-zinc-tin oxide/Ag/indium-zinc-tin oxide multilayer electrodes

Science.gov (United States)

Oh, Dohyun; Yun, Dong Yeol; Cho, Woon-Jo; Kim, Tae Whan

2014-08-01

Transparent indium-zinc-tin oxide (IZTO)-based thin-film transistors (TFTs) with IZTO/Ag/IZTO multilayer electrodes were fabricated on glass substrates using a tilted dual-target radio-frequency magnetron sputtering system. The IZTO TFTs with IZTO/Ag/IZTO multilayer electrodes exhibited a high optical transmittance in a visible region. The threshold voltage, the mobility, and the on/off-current ratio of the TFTs with IZTO/Ag/IZTO multilayer electrodes were enhanced in comparison with those of the TFTs with ITO electrodes. The source/drain contact resistance of the IZTO TFTs with IZTO/Ag/IZTO multilayer electrodes was smaller than that of the IZTO TFTs with ITO electrodes, resulting in enhancement of their electrical characteristics.

Fast-neutron total and elastic-scattering cross sections of elemental indium

International Nuclear Information System (INIS)

Smith, A.B.; Guenther, P.T.; Whalen, J.F.

1982-11-01

Broad-resolution neutron total cross sections of elemental indium were measured from 0.8 to 4.5 MeV. Differential-elastic-scattering cross sections were measured from approx. = 1.5 to 3.8 MeV at intervals of approx. = 50 to 200 keV and at scattering angles in the range 20 to 160 degrees. The experimental results are interpreted in terms of the optical-statistical model and are compared with respective values given in ENDF/B-V

Electrical and optical properties of thin indium tin oxide films produced by pulsed laser ablation in oxygen or rare gas atmospheres

DEFF Research Database (Denmark)

Thestrup, B.; Schou, Jørgen; Nordskov, A.

1999-01-01

Films of indium tin oxide (ITO) have been produced in different background gases by pulsed laser deposition (PLD). The Films deposited in rare gas atmospheres on room temperature substrates were metallic, electrically conductive, but had poor transmission of visible light. For substrate temperatu......Films of indium tin oxide (ITO) have been produced in different background gases by pulsed laser deposition (PLD). The Films deposited in rare gas atmospheres on room temperature substrates were metallic, electrically conductive, but had poor transmission of visible light. For substrate...

Band structure dynamics in indium wires

Science.gov (United States)

Chávez-Cervantes, M.; Krause, R.; Aeschlimann, S.; Gierz, I.

2018-05-01

One-dimensional indium wires grown on Si(111) substrates, which are metallic at high temperatures, become insulating below ˜100 K due to the formation of a charge density wave (CDW). The physics of this transition is not conventional and involves a multiband Peierls instability with strong interband coupling. This CDW ground state is readily destroyed with femtosecond laser pulses resulting in a light-induced insulator-to-metal phase transition. The current understanding of this transition remains incomplete, requiring measurements of the transient electronic structure to complement previous investigations of the lattice dynamics. Time- and angle-resolved photoemission spectroscopy with extreme ultraviolet radiation is applied to this end. We find that the transition from the insulating to the metallic band structure occurs within ˜660 fs, which is a fraction of the amplitude mode period. The long lifetime of the transient state (>100 ps) is attributed to trapping in a metastable state in accordance with previous work.

Study the physical and optoelectronic properties of silver gallium indium selenide AgGaInSe2/Si heterojunction solar cell

Science.gov (United States)

Hassun, Hanan K.

2018-05-01

AgGa1-x InxSe2 (AGIS) thin films was deposited on Si and glass substrates by thermal evaporation at RT and different ratios of Indium (x=0.2, 0.5, 0.8). The synthetics properties of AGIS thin film have been examined using X-ray diffraction and AFM. AGIS thin films possessed a polycrystalline tetragonal structure. Average diameter and roughness calculated from AFM images shows an increase in its value with increasing the ratios of Indium. Hall measurements showed n-type conduction with high mobility. The AgGa0.2In0.8Se2 thin film solar cell with a band gap of 1.65eV exhibit a total efficiency of 6.3% with open-circuit voltage Voc 0.38V, short circuit current Jsc 29 mA/cm2, fill factor FF 0.571 and total area 1 cm2. The built-in potential Vbi, concentration of majoritarian carrier ND and depletion width w are definite under different ratios of Indium from C-V amount.

The solvent extraction of zinc, iron, and indium from chloride solutions by neutral organophosphorus compounds

International Nuclear Information System (INIS)

Preston, J.S.; Du Preez, A.C.

1985-01-01

The preparation of several neutral organophosphorus compounds and their evaluation as selective extractants for zinc in chloride media are described. The compounds belong to the series trialkyl phosphates (RO) 3 PO, dialkyl alkylphosphonates R'PO(OR) 2 , alkyl dialkylphosphinates R 2 'PO(OR), and trialkyl-phosphine oxides R 3 'PO. They were characterized by measurement of their physical properties (melting and boiling points, refractive indices, and densities), and their purities were confirmed by osmometric determination of their molecular masses; by carbon and hydrogen microanalysis; by the titrimetric determination of acidic impurities; and, for liquid products, by comparison of their experimental molar refractivities with empirical values. Metal-distribution equilibria were determined for solutions of the extractants in xylene and aqueous phase containing 0,5 to 5,0 M sodium chloride. Moderately good selectivities were shown for zinc(II) over iron(III), and excellent selectivities were shown for zinc(II) over iron(II), copper(II), lead(II), and cadmium(II). The extraction of indium(III) was similar to that of zinc(II). The extraction of zinc(III), iron(III), and indium(III) increased markedly through the series. (RO) 3 PO 2 2 'PO(OR) 3 'PO. The incorporation of phenyl groups into the compounds led to weaker extraction. The extracted complexes of zinc(II), iron(III), and indium(III) have the stoichiometries ZnCl 2 L 2 ,FeCl 3 L 2 (H 2 O), and InCl 3 L 2 (H 2 O) respectively, where L represents the neutral organophosphorus compound

Upscaling of Indium Tin Oxide (ITO)-Free Polymer Solar Cells

DEFF Research Database (Denmark)

Angmo, Dechan

Polymer solar cells (PSCs) aim to produce clean energy that is cost-competitive to energy produced by fossil fuel-based conventional energy sources. From an environmental perspective, PSCs already compares favorably to other solar cell technologies in terms of fewer emissions of greenhouse gases......, represents majority of the share of cost and energy footprint in terms of materials and processing in a conventional PSC module. Furthermore, the scarcity of indium is feared to create bottleneck in the dawning PSC industry and its brittle nature is an obstacle for fast processing of PSCs on flexible...

Anomalous behaviour of screw dislocations in quenched indium antimonide monocrystals

International Nuclear Information System (INIS)

Alekseenko, V.I.; Mostovoj, V.M.

1991-01-01

Anomalies of screw dislocation mobility in indium antimonide single crystals quenched after annealing were detected experimentally. Taking into accout specific nature of thermal treatment an enhanced attention is paid to the technique of the experiment. It is shown that the observed peculiarities can be explained using a model of thermoactivated movement of excessive bends over stoppers at the dislocation line. Proceeding from the assumption on the nature of stoppers, the values of stopper energy barriers overcome by an excessive bend are determined on the basis of the above model of excessive bend movement

Transparent heaters based on solution-processed indium tin oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Im, Kiju [Department of Electrical Engineering and Institute for Nano Science, Korea University, 5-1, Anam-dong, Sungbuk-gu, Seoul 136-701 (Korea, Republic of); Research Institute of TNB Nanoelec Co. Ltd., Seoul 136-701 (Korea, Republic of); Cho, Kyoungah [Department of Electrical Engineering and Institute for Nano Science, Korea University, 5-1, Anam-dong, Sungbuk-gu, Seoul 136-701 (Korea, Republic of); Kim, Jonghyun [Research Institute of TNB Nanoelec Co. Ltd., Seoul 136-701 (Korea, Republic of); Kim, Sangsig, E-mail: sangsig@korea.ac.k [Department of Electrical Engineering and Institute for Nano Science, Korea University, 5-1, Anam-dong, Sungbuk-gu, Seoul 136-701 (Korea, Republic of)

2010-05-03

We demonstrate transparent heaters constructed on glass substrates using solution-processed indium tin oxide (ITO) nanoparticles (NPs) and their heating capability. The heat-generating characteristics of the heaters depended significantly on the sintering temperature at which the ITO NPs deposited on a glass substrate by spin-coating were transformed thermally into a solid film. The steady-state temperature of the ITO NP film sintered at 400 {sup o}C was 163 {sup o}C at a bias voltage of 20 V, and the defrosting capability of the film was confirmed by using dry-ice.

Measurement of acute Q-wave myocardial infarct size with single photon emission computed tomography imaging of indium-111 antimyosin.

Science.gov (United States)

Antunes, M L; Seldin, D W; Wall, R M; Johnson, L L

1989-04-01

Myocardial infarct size was measured by single photon emission computed tomography (SPECT) following injection of indium-111 antimyosin in 27 patients (18 male and 9 female; mean age 57.4 +/- 10.5 years, range 37 to 75) who had acute transmural myocardial infarction (MI). These 27 patients represent 27 of 35 (77%) consecutive patients with acute Q-wave infarctions who were injected with indium-111 antimyosin. In the remaining 8 patients either tracer uptake was too faint or the scans were technically inadequate to permit infarct sizing from SPECT reconstructions. In the 27 patients studied, infarct location by electrocardiogram was anterior in 15 and inferoposterior in 12. Nine patients had a history of prior infarction. Each patient received 2 mCi of indium-111 antimyosin followed by SPECT imaging 48 hours later. Infarct mass was determined from coronal slices using a threshold value obtained from a human torso/cardiac phantom. Infarct size ranged from 11 to 87 g mean 48.5 +/- 24). Anterior infarcts were significantly (p less than 0.01) larger (60 +/- 20 g) than inferoposterior infarcts (34 +/- 21 g). For patients without prior MI, there were significant inverse correlations between infarct size and ejection fraction (r = 0.71, p less than 0.01) and wall motion score (r = 0.58, p less than 0.01) obtained from predischarge gated blood pool scans. Peak creatine kinase-MB correlated significantly with infarct size for patients without either reperfusion or right ventricular infarction (r = 0.66). Seven patients without prior infarcts had additional simultaneous indium-111/thallium-201 SPECT studies using dual energy windows.(ABSTRACT TRUNCATED AT 250 WORDS)

The distribution of gallium, germanium and indium in conventional and non-conventional resources. Implications for global availability

Energy Technology Data Exchange (ETDEWEB)

Frenzel, Max

2016-10-25

Over the past 10 years, increased interest in the supply security of metal and mineral raw materials has resulted in the compilation of many lists of materials of particular concern. These materials are generally referred to as 'critical'. They are perceived to be both of high economic importance, as well as subject to high supply risks. Of particular relevance with respect to supply risk is the assessment of geological risk factors. However, this aspect is not considered in sufficient detail in most studies. In particular, the specific features of elements won as by-products are not adequately represented in any assessment. Yet many of these elements are often classified as critical, mostly due to their apparent importance in high-tech applications, the intransparency of their respective markets and resulting price volatility, and the concentration of their production in China. Gallium, germanium and indium are all good examples of such elements. All three are similar in many respects, and commonly have a similar rating in both the economic importance and supply risk dimensions. The aim of this work was to use these three elements as examples, and investigate whether they are truly as similar as current assessments suggest, or whether there are large underlying differences in their specific supply situations. In particular, the focus was on physical supply limitations: Since by-products can only be extracted with other main-product raw materials, their rate of extraction is limited by the extraction rate of these main products. This means that the relevant quantities for an assessment of their physical supply limitations are not reserves and/or resources, but supply potentials. The supply potential is the quantity of a given by-product which could theoretically be extracted under current market conditions (price, technology) per year if all suitable raw materials were processed accordingly. To assess the supply potentials of gallium, germanium and indium

Construction of two novel indium phosphites with (3,6)- and (3,5)-connected frameworks: Synthesis, structure and characterization

International Nuclear Information System (INIS)

Li Huiduan; Zhang Lirong; Huo Qisheng; Liu Yunling

2013-01-01

Two novel anionic indium phosphites, formulated as [H 3 O][In(HPO 3 ) 2 ] (1) and [C 4 H 12 N 2 ][In 2 (HPO 3 ) 3 (C 2 O 4 )] (2), were prepared under hydrothermal conditions by using piperazine (PIP) as a structure-directing agent (SDA). Single-crystal X-ray diffraction analysis reveals that compounds 1 and 2 crystallize in the hexagonal space group P6 3 mc (No. 186) and orthorhombic space group Cmcm (No. 63), respectively. Compound 1, constructed from InO 6 octahedra and HPO 3 pseudo-pyramids, exhibits a rare (3,6)-connected layer structure with kgd (Kagome dual) topology. Compound 2, on the other hand, features a 3D phosphite-oxalate hybrid structure with intersecting 8- and 12-MRs channels. From a topological perspective 2 can be regarded as a (3, 5)-connected binodal net with the Schläfli symbol (4 2 .6)(4 2 .6 5 .8 3 ). Highlights: ► Two novel indium phosphite and indium phosphite-oxalate hybrid compounds are synthesized. ► (3, 6)-connected layer structure with kgd topology. ► (3,5)-connected binodal net with the Schläfli symbol (4 2 .6)(4 2 .6 5 .8 3 ).

Ion beam analysis of aluminium in thin layers

International Nuclear Information System (INIS)

Healy, M.J.F.; Pidduck, A.J.; Dollinger, G.; Gorgens, L.; Bergmaier, A.

2002-01-01

This work quantifies aluminium in thin surface and near surface layers. In one example, the layer overlies a thin gallium nitride layer on an aluminium oxide substrate and in a second example the aluminium exists just below the surface of an indium arsenide substrate. The technique of non-Rutherford elastic backscattering of protons was used for the samples where aluminum in the layer of interest needed to be resolved from aluminium in the sapphire substrate and the results were corroborated at the Technische Universitaet Muenchen using heavy ion elastic recoil detection analysis. In the second example, where it was unnecessary to isolate the signal of aluminium in the layer of interest (as the substrate contained no aluminium), then the 27 Al(d,p 01 ) 28 Al nuclear reaction was used. The elastic proton scattering cross section of aluminum was found to vary very rapidly over the energy range of interest

Oxygen effect of transparent conducting amorphous Indium Zinc Tin Oxide films on Polyimide substrate for flexible electrode

International Nuclear Information System (INIS)

Ko, Yoon Duk; Lee, Chang Hun; Moon, Doo Kyung; Kim, Young Sung

2013-01-01

This paper discusses the effect of oxygen on the transparent conducting properties and mechanical durability of the amorphous indium zinc tin oxide (IZTO) films. IZTO films deposited on flexible clear polyimide (PI) substrate using pulsed direct current (DC) magnetron sputtering at room temperature under various oxygen partial pressures. All IZTO films deposited at room temperature exhibit an amorphous structure. The electrical and optical properties of the IZTO films were sensitively influenced by oxygen partial pressures. At optimized deposition condition of 3.0% oxygen partial pressure, the IZTO film shows the lowest resistivity of 6.4 × 10 −4 Ωcm, high transmittance of over 80% in the visible range, and figure of merit value of 3.6 × 10 −3 Ω −1 without any heat controls. In addition, high work function and good mechanical flexibility of amorphous IZTO films are beneficial to flexible applications. It is proven that the proper oxygen partial pressure is important parameter to enhance the transparent conducting properties of IZTO films on PI substrate deposited at room temperature. - Highlights: • Indium zinc tin oxide (IZTO) films were deposited on polyimide at room temperature. • Transparent conducting properties of IZTO were influenced with oxygen partial pressure. • The smooth surface and high work function of IZTO were beneficial to anode layer. • The mechanical reliability of IZTO shows better performance to indium tin oxide film