Effects of Sm addition on microstructure and mechanical properties of a Mg-10Y alloy

Directory of Open Access Journals (Sweden)

Li Quanan

2014-01-01

Full Text Available To further increase the mechanical properties, 0.5wt.% Sm was introduced to a Mg-10Y alloy in this study. The effects of Sm addition on the microstructures and mechanical properties of the Mg-10Y alloy, especially the aged Mg-10Y alloy, were investigated. The microstructure observation and tensile tests were performed by using an optical microscopy, a scanning electron microscopy and a universal material testing machine, respectively. The phase analysis was performed using X-ray diffractometer. The results show that the 0.5wt.% Sm addition can not only promote the formation of fine and dispersed Mg24Y5 phases, but also improve their morphology and distribution; it also increases the thermal stability of Mg24Y5 phases. Sm addition is seen to increase the ultimate tensile strength of Mg-10Y alloy at elevated temperatures (200, 250, 300 and 350 ℃, while decrease the elongation. But the elongation is still up to 7.5% even at 350 ℃. In the range of 250 ℃ to 300℃, the ultimate tensile strength of the alloy reaches its maximum (with a range average of 235 MPa and is not sensitive to the temperature change, which is very useful to the application of heat-resistant magnesium alloys. Even at 350 ℃, the ultimate tensile strength of Mg-10Y-0.5Sm is still up to 155 MPa. Considering both of the ultimate tensile strength and elongation, the maximum application temperature of the Mg-10Y-0.5Sm alloy can be up to 300 ℃. The strengthening mechanisms of Mg-10Y-0.5Sm alloy are mainly attributed to dispersion strengthening of Mg24Y5 phase particles with a certain solubility of Sm and grain refinement strengthening of α-Mg matrix.

Electrochemical properties of the ball-milled LaMg10NiMn alloy with Ni powders

International Nuclear Information System (INIS)

Wang Yi; Wang Xin; Gao Xueping; Shen Panwen

2008-01-01

The electrochemical characteristics of the ball-milled LaMg 10 NiMn alloys with Ni powders were investigated. It was found that the ball-milled LaMg 10 NiMn + 150 wt.% Ni composite exhibited higher first discharge capacity and better cycle performance. By means of the analysis of electrochemical impedance spectra (EIS), it was shown that the existence of manganese in LaMg 10 NiMn alloy increased the electrocatalytic activity due to its catalytic effect, and destabilized metal hydrides, and so reduced the hydrogen diffusion resistance. These contributed to the higher discharge capacity of the ball-milled LaMg 10 NiMn-Ni composite. According to the analytical results of X-ray diffraction (XRD), EIS and steady-state polarization (SSP) experiments, the inhibition of metal corrosion is not the main reason for the better cycle performance. The main reason is that the electrochemical reaction resistance of the ball-milled LaMg 10 NiMn-Ni composite is always lower than that of the ball-milled LaMg 10 Ni 2 -Ni composite because the former one contains manganese, which is a catalyst for the electrode reaction

Express penetration of hydrogen on Mg(10͞13) along the close-packed-planes.

Science.gov (United States)

Ouyang, Liuzhang; Tang, Jiajun; Zhao, Yujun; Wang, Hui; Yao, Xiangdong; Liu, Jiangwen; Zou, Jin; Zhu, Min

2015-06-01

Metal atoms often locate in energetically favorite close-packed planes, leading to a relatively high penetration barrier for other atoms. Naturally, the penetration would be much easier through non-close-packed planes, i.e. high-index planes. Hydrogen penetration from surface to the bulk (or reversely) across the packed planes is the key step for hydrogen diffusion, thus influences significantly hydrogen sorption behaviors. In this paper, we report a successful synthesis of Mg films in preferential orientations with both close- and non-close-packed planes, i.e. (0001) and a mix of (0001) and (10͞13), by controlling the magnetron sputtering conditions. Experimental investigations confirmed a remarkable decrease in the hydrogen absorption temperature in the Mg (10͞13), down to 392 K from 592 K of the Mg film (0001), determined by the pressure-composition-isothermal (PCI) measurement. The ab initio calculations reveal that non-close-packed Mg(10͞13) slab is advantageous for hydrogen sorption, attributing to the tilted close-packed-planes in the Mg(10͞13) slab.

In vivo and in vitro degradation comparison of pure Mg, Mg-10Gd and Mg-2Ag: a short term study

Directory of Open Access Journals (Sweden)

I Marco

2017-02-01

Full Text Available The purpose of this study was to compare short term in vitro and in vivo biodegradation studies with low purity Mg (> 99.94 %, Mg-10Gd and Mg-2Ag designed for biodegradable implant applications. Three in vitro testing conditions were applied, using (i phosphate buffered saline (PBS, (ii Hank’s balanced salt solution (HBSS and (iii Dulbecco’s modified eagle medium (DMEM in 5 % CO2 under sterile conditions. Gas evolution and mass loss (ML were assessed, as well as the degradation layer, by elemental mapping and scanning electron microscopy (SEM. In vivo, implantations were performed on male Sprague-Dawley rats evaluating both, gas cavity volume and implant volume reduction by micro-computed tomography (µCT, 7 d after implantation. Samples were produced by casting, solution heat treatment and extrusion in disc and pin shape for the in vitro and in vivo experiments, respectively. Results showed that when the processing of the Mg sample varied, differences were found not only in the alloy impurity content and the grain size, but also in the corrosion behaviour. An increase of Fe and Ni or a large grain size seemed to play a major role in the degradation process, while the influence of alloying elements, such as Gd and Ag, played a secondary role. Results also indicated that cell culture conditions induced degradation rates and degradation layer elemental composition comparable to in vivo conditions. These in vitro and in vivo degradation layers consisted of Mg hydroxide, Mg-Ca carbonate and Ca phosphate.

The efficacy and safety of 10 mg vortioxetine in the treatment of major depressive disorder: a meta-analysis of randomized controlled trials

Directory of Open Access Journals (Sweden)

Li G

2016-02-01

Full Text Available Guangjian Li, Xu Wang, Dihui Ma Department of Neurology and Neuroscience Center, First Hospital of Jilin University, Changchun, People’s Republic of China Background: Vortioxetine is an investigational multimodal antidepressant. We conducted this meta-analysis to assess the efficacy and safety of 10 mg vortioxetine in the treatment of major depressive disorder (MDD. Methods: Randomized controlled trials (RCTs published in PubMed, Web of Science, Embase, and ClinicalTrials.gov were systematically reviewed to assess the treatment effects and safety profiles of patients with MDD who were treated with 10 mg vortioxetine. The outcome measures included response rate, remission rate, changes from baseline in Montgomery–Asberg Depression Rating Scale (MADRS, Hamilton Rating Scale for Depression (24-items (HAM-D24, Clinical Global Impression-Severity (CGI-S, and Clinical Global Impression-Improvement (CGI-I scores. Results were expressed with risk ratio or weighted mean difference with 95% confidence intervals. Pooled results were calculated using a fixed-effects model or a random-effects model according to the heterogeneity among included trials. Results: Six RCTs with a total of 1,801 patients met the inclusion criteria and were included in this meta-analysis. The 10 mg vortioxetine dose significantly increased the response rate and remission rate in the treatment of MDD compared with placebo. Moreover, there was a statistically significant reduction from baseline in the MADRS, HAM-D24, CGI-S, and CGI-I scores with 10 mg vortioxetine vs placebo. The incidence of treatment-emergent adverse events such as nausea, vomiting, constipation, and hyperhidrosis was higher in the 10 mg vortioxetine group than in the placebo group. Conclusion: Vortioxetine 10 mg can significantly increase the response rate and remission rate, and reduce the MADRS, HAM-D24, CGI-S, and CGI-I scores in patients with MDD with an acceptable risk of treatment-emergent adverse

Behavior of methyl orange and orange 10 (orange G) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe

International Nuclear Information System (INIS)

Cruz N, G.

2015-01-01

This work is focused on studying the sorption capacity of methyl orange dye (Nm) and orange 10 (N-10) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe uncalcined and calcined previously at 500 degrees Celsius. Sorption isotherms were determined and the study of the kinetics of sorption was performed. The materials were characterized before and after sorption processes of these dyes by X-ray diffraction, scanning electron microscopy, the specific surface area determination by the Brunauer-Emmett-Teller method, thermogravimetry coupled to mass and infrared spectrometry. The hydrotalcite type compounds reported in this paper were prepared in the laboratory and their acronyms are: HTMgAlG1, HTMgAlMO, HTMgFeG1 and HTMgFeG2. Note that in this work the best conditions for preparing compounds of Mg/Fe were found. From patterns of X-ray diffraction was identified the typical crystal structure of the hydrotalcite type compounds. By scanning electron microscopy the morphology could be determined in the form of flakes characteristics of these compounds. Likewise with elemental analysis of energy dispersive X-ray spectroscopy the presence of Mg, Al, Fe and C, elements of interest for this study was determined. The compounds presented a specific surface area relatively high from 80 to 120 m 2 /g. Thermogravimetry results presented spectra of mass loss very characteristic associated to water losses, dehydroxylation and decarboxylation. The characteristic bands of water and carbonate were assigned by infrared spectroscopy and the bands corresponding to the dyes sulfonates were identified only for the calcined materials. The sorption capacities found of these compounds were as follows: for Nm in the compound HTMgAlG1 uncalcined was 17.82 mg/g for an initial concentration of 200 mg/L and for calcined (HTMgAlMOcal) of 99.8 mg/g with and initial concentration of 1000 mg/L. Moreover, the sorption capacity of the dye N-10 in this same material was 17.92 mg/g and 99.4 mg

Selective laser melting of carbon/AlSi10Mg composites: Microstructure, mechanical and electronical properties

Energy Technology Data Exchange (ETDEWEB)

Zhao, Xiao; Song, Bo, E-mail: bosong@hust.edu.cn; Fan, Wenrui; Zhang, Yuanjie; Shi, Yusheng

2016-04-25

Carbon nanotubes/AlSi10Mg composites has drawn lots of attention in structural engineering and functional device applications due to its extraordinary high elastic modulus and mechanical strength as well as excellent electrical and thermal conductivities. In this study, the CNTs/AlSi10Mg composites was firstly prepared and then processed by selective laser melting. The powder preparation, SLM process, and microstructure evolution, properties were clarified. The results showed that CNTs were decomposed due to the direct interaction with the laser beam. The SLMed composites displayed a similar microstructure to that of SLMed AlSi10Mg. The common brittleness phase Al{sub 4}C{sub 3} didn't form, and the carbon dispersion strengthening was observed. The electrical resistivity of the composites was reduced significantly and the hardness was improved. - Highlights: • Carbon nanotubes/AlSi10Mg powder were prepared by slurry ball milling process. • Carbon nanotubes/AlSi10Mg composites were firstly prepared by SLM. • The electrical resistivity of the composites was significantly reduced and hardness was improved.

Development and Characterisation of Aluminium Matrix Nanocomposites AlSi10Mg/MgAl2O4 by Laser Powder Bed Fusion

Directory of Open Access Journals (Sweden)

Giulio Marchese

2018-03-01

Full Text Available Recently, additive manufacturing techniques have been gaining attention for the fabrication of parts from aluminium alloys to composites. In this work, the processing of an AlSi10Mg based composite reinforced with 0.5% in weight of MgAl2O4 nanoparticles through laser powder bed fusion (LPBF process is presented. After an initial investigation about the effect of process parameters on the densification levels, the LPBF materials were analysed in terms of microstructure, thermo-mechanical and mechanical properties. The presence of MgAl2O4 nanoparticles involves an increment of the volumetric energy density delivered to the materials, in order to fabricate samples with high densification levels similar to the AlSi10Mg samples. However, the application of different building parameters results in modifying the size of the cellular structures influencing the mechanical properties and therefore, limiting the strengthening effect of the reinforcement.

Comparison of the effects of esomeprazole 40 mg, rabeprazole 20 mg, lansoprazole 30 mg, and pantoprazole 40 mg on intragastrıc pH in extensive metabolizer patients with gastroesophageal reflux disease.

Science.gov (United States)

Çelebi, Altay; Aydın, Dinçer; Kocaman, Orhan; Konduk, Buğra Tolga; Şentürk, Ömer; Hülagü, Sadetin

2016-09-01

Studies on the therapeutic efficacy of proton pump inhibitors (PPIs) in patients with gastroesophageal reflux disease (GERD) have been recently published. In most of these studies, comparison of only two PPIs have been made. There are few studies on the comparison of four or more PPIs. We aimed to compare the acid inhibitory effects of esomeprazole 40 mg, rabeprazole 20 mg, lansoprazole 30 mg, and pantoprazole 40 mg on days 1 and 5 of treatment in patients with GERD, who were extensive metabolizers in regard to the CYP2C19 genotype. Helicobacter pylori-negative with typical symptoms of GERD patients were randomly divided into four treatment groups. Efficacy analysis on days 1 and 5 were performed on the four groups which comprised 10 (esomeprazole), 11 (rabeprazole), 10 (lansoprazole), and 10 (pantoprazole) patients. On day 1 of PPI treatment, the mean percentage of time with intragastric Ph>4 were 54%, 58%, 60%, and 35% for the groups, respectively, and on day 5, these values were 67%, 60%, 68%, and 59%, respectively. Esomeprazole, rabeprazole, and lansoprazole were found to be superior to pantoprazole on the first day of treatment. Pantoprazole is a less potent proton pump inhibitor than the other PPIs tested on the first day of treatment. When the time needed to raise the intragatric pH to over 4 was evaluated, esomeprazole was found to have the most rapid action, followed by lansoprazole and rabeprazole.

Structure and thermal properties of as-fabricated U-7Mo/Mg and U-10Mo/Mg low-enriched uranium research reactor fuels

Energy Technology Data Exchange (ETDEWEB)

Kulakov, Mykola, E-mail: mykola.kulakov@cnl.ca [Fuel Development Branch, Canadian Nuclear Laboratories, Chalk River, ON K0J 1J0 Canada (Canada); Saoudi, Mouna [Fuel Development Branch, Canadian Nuclear Laboratories, Chalk River, ON K0J 1J0 Canada (Canada); Piro, Markus H.A. [Fuel and Fuel Channel Safety Branch, Canadian Nuclear Laboratories, Chalk River, ON K0J 1J0 Canada (Canada); Donaberger, Ronald L. [Canadian Neutron Beam Centre, Chalk River, ON K0J 1J0 Canada (Canada)

2017-02-15

Aluminum-clad U-7Mo/Mg and U-10Mo/Mg pin-type mini-elements (with a core uranium loading of 4.5 gU/cm{sup 3}) have been fabricated at the Canadian Nuclear Laboratories for experimental tests and ultimately for use in research and test reactors. In this study, the microstructure and phase composition of unirradiated U-7Mo/Mg and U-10Mo/Mg fuel cores were analyzed using optical and scanning electron microscopy, and neutron powder diffraction. Thermal properties were characterized using a combination of experimental measurements and thermodynamic calculations. The thermal diffusivity was measured using the laser flash method. The temperature-dependent specific heat capacities were calculated based on the linear rule of mixture using the weight fraction of different crystalline phases and their specific heat capacity values taken from the literature. The thermal conductivity was then calculated using the measured thermal diffusivity, the measured density and the calculated specific heat capacity. The resulting thermal conductivity is practically identical for both types of fuel. The in-reactor temperatures were predicted using conjugate heat transfer simulations. - Highlights: • Neutron diffraction analysis shows that most of the γ-U(Mo) phase was retained in as-fabricated U-7Mo/Mg and U-10Mo/Mg fuel cores. • The experimental thermal conductivity of both types of fuel is practically identical. • Based on conjugate heat transfer simulations, under normal operating conditions, the in-reactor fuel centreline temperature is about 510 K.

Single crystal structures of the new vanadates CuMgVO{sub 4} and AgMgVO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Ben Yahia, Hamdi, E-mail: Hyahia@qf.org.qa [Research Institute of Electrochemical Energy, National Institute of Advanced Industrial Science and Technology (AIST), 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577 (Japan); Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, Qatar Foundation, PO Box 5825, Doha (Qatar); Shikano, Masahiro, E-mail: shikano.masahiro@aist.go.jp [Research Institute of Electrochemical Energy, National Institute of Advanced Industrial Science and Technology (AIST), 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577 (Japan); Essehli, Rachid; Belharouak, Ilias [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, Qatar Foundation, PO Box 5825, Doha (Qatar)

2016-08-01

The new compounds CuMgVO{sub 4} and AgMgVO{sub 4} have been synthesized by a solid state reaction route. Their crystal structures were determined from single-crystal X-ray diffraction data. CuMgVO{sub 4} crystallizes with Na{sub 2}CrO{sub 4}-type structure with space group Cmcm, a = 5.6932 (10), b = 8.7055 (15), c = 6.2789 (10) Å, V = 311.20 (9) Å{sup 3}, and Z = 4, whereas AgMgVO{sub 4} crystallizes in the maricite-type structure with space group Pnma, a = 9.4286 (14), b = 6.7465 (10), c = 5.3360 (8) Å, V = 339.42 (9) Å{sup 3}, and Z = 4. Both structures of CuMgVO{sub 4}, and AgMgVO{sub 4} contain MgO{sub 4} chains made up of edge-sharing MgO{sub 6} octahedra. In CuMgVO{sub 4} the MgO{sub 4} chains are interconnected through CuVO{sub 4} double chains made up of VO{sub 4} and CuO{sub 4} tetrahedra sharing corners and edges, however in AgMgVO{sub 4} the chains are interlinked by the VO{sub 4} and AgO{sub 4} tetrahedra sharing only corners. - Highlights: • We have been able to grow CuMgVO{sub 4} and AgMgVO{sub 4} single crystals. • We solved their crystal structures using single crystal data. • We compared the crystal structures of CuMgVO{sub 4} and AgMgVO{sub 4}.

Raman spectra of MgSiO3 . 10% Al2O3-perovskite at various pressures and temperatures

International Nuclear Information System (INIS)

Liu Lingun; Irifune, T.

1995-01-01

Variations of Raman spectra of MgSiO 3 . 10% Al 2 O 3 -perovskite were investigated up to about 270 kbar at room temperature and in the range 108-425 K at atmospheric pressure. Like MgSiO 3 -perovskite, the Raman frequencies of MgSiO 3 . 10% Al 2 O 3 -perovskite increase nonlinearly with increasing pressure and decrease linearly with increasing temperature within the experimental uncertainties and the range investigated. A comparison of these data with those of MgSiO 3 -perovskite suggests that MgSiO 3 . 10% Al 2 O 3 -perovskite is slightly more compressible than MgSiO 3 -perovskite, and that the volume thermal expansion for MgSiO 3 . 10% Al 2 O 3 -perovskite is also slightly greater than that for MgSiO 3 -perovskite. (orig.)

Evolución de las propiedades mecánicas con la temperatura de cintas amorfas Mg10Ni10Y

Directory of Open Access Journals (Sweden)

Torrijos, M. A.

2006-02-01

Full Text Available The mechanical behaviour by tensile strength test from room temperature to 350 ºC in the rapidly solidified Mg-10Ni-10Y (at. % ribbon has been studied. To determine the effect of yttrium additions the results are compared with those of Mg-11Ni studied in a previous work. Before studding the mechanical behavior of the material the thermal stability of the amorphous ribbon and the crystallization reactions were determined by DSC experiments. Results show that yttrium stabilizes the amorphous phase but it has not reinforcement effect. The tensile strength and elongation to failure values of the ternary alloy are lower than those of Mg-11Ni

El objetivo de este estudio es la caracterización mecánica, mediante ensayos de tracción, desde temperatura ambiente hasta 350 °C, de una aleación amorfa de composición Mg-10Ni-10Y (% at. obtenida mediante solidificación rápida por la técnica de la rueda. Se analiza la influencia de la adición de itrio al Mg-Ni para lo cual los resultados se comparan con los de la aleación binaria Mg-11Ni estudiada previamente. Antes de iniciar la caracterización mecánica del material, se realizó un estudio mediante calorimetría diferencial de barrido para comprobar la naturaleza amorfa de la cinta, analizar su estabilidad térmica y conocer las transformaciones que experimenta hasta la cristalización. Los resultados indican que el itrio es un estabilizador de la fase amorfa pero no mejora las propiedes mecánicas de la cinta binaria. Los valores de resistencia mecánica y alargamiento a rotura medidos en la cinta con itrio son menores que los obtenidos para la aleación binaria.

Comparison of the efficacy and safety of 10-mg empagliflozin every day versus every other day in Japanese patients with Type 2 Diabetes Mellitus: a pilot trial.

Science.gov (United States)

Obata, Fumiaki; Tani, Kenji; Yamaguchi, Harutaka; Tabata, Ryo; Bando, Hiroyasu; Imoto, Issei

2017-01-01

The terminal elimination half-life (t1/2) of empagliflozin is 13.1 hours. Accordingly, we hypothesized that the administration of empagliflozin every other day might improve glycemic control in patients with type 2 diabetes mellitus, not being inferior to the therapy every day. We investigated the clinical effects and safety of the addition of empagliflozin every day or every other day to type 2 diabetic patients with a poor control in glycemia. Thirteen Japanese patients diagnosed as type 2 diabetes mellitus recruited to this study. Subjects were divided into two groups; one was treatment with 10 mg of empagliflozin every day (Group A), the other was 10 mg of empagliflozin every other day (Group B). The comparable study of multiple clinical indexes between the 2 groups was made before and 8, 16, and 24 weeks after the treatment. After the treatment for 24 weeks, the HbA1c level was decreased both in group A (from 7.5%±1.1% to 6.5%±0.8%) and in group B (from 7.6%±0.8% to 7.2%±0.5%). This pilot trial suggested the possibility of 10-mg every other day administration with empagliflozin for Japanese patients with type 2 diabetes mellitus. J. Med. Invest. 64: 50-57, February, 2017.

Crystal structures of the solid solutions Na3Zn0.912Cd0.088B5O10 and Na3Zn0.845Mg0.155B5O10

Directory of Open Access Journals (Sweden)

Xue-An Chen

2017-11-01

Full Text Available Two new pentaborates, trisodium zinc cadmium pentaborate, Na3Zn0.912Cd0.088B5O10, and trisodium zinc magnesium pentaborate, Na3Zn0.845Mg0.155B5O10, have been synthesized by high-temperature solution reactions at 1023 K. Their crystal structures were determined by single-crystal X-ray diffraction. Both solid solutions crystallize in the orthorhombic form of the parent compound Na3ZnB5O10 (space group type Pbca, Z = 8 and contain the double ring [B5O10]5− anion composed of one BO4 tetrahedron and four BO3 triangles as the basic structural motif. The anions are bridged by tetrahedrally coordinated and occupationally disordered M2+ (M = Zn/Cd, Zn/Mg cations via common O atoms to form [MB5O10]n3n− layers. The intralayer intersecting channels and the interlayer voids are occupied by Na+ cations to balance the charge.

Mechano-luminescence studies of nano ZnMgAl10O17:Eu phosphor under UV irradiation

Science.gov (United States)

Verma, Akshkumar; Verma, Ashish; Panda, Maheswar

2018-05-01

ZnMgAl10O17:Eu nano phosphors were prepared successfully, using the combustion route by employing urea as a fuel. The structural, and Morphological, properties were measured using x-ray diffraction (XRD) Scanning electron microscopy (SEM) transition electron microscopy. The BET surface area of sample were found to be of ˜13.92 m2/g. The ML (Mechano-luminescence) were measured to the home made instrument. The phosphor showed more strong and high ML intensity to the without UV irradiated material. Therefore ZnMgAl10O17:Eu2+ phosphor may use as a damage sensor and dosimetry material. The ML emission spectra of the Zn0.99MgAl10O17:Eu0.01 phosphor showed the characteristic Eu2+ emission peaks ˜453nm (blue) originating from the transitions 4f65d1→4f7, Therefore ZnMgAl10O17:Eu2+ phosphor may use as a blue phosphor material.

L10 ordered structures in Al-Cu-(Mg alloys at the early stages of elevated temperature aging

Directory of Open Access Journals (Sweden)

Fuzhong, Xia

2016-09-01

Full Text Available This study concerns the precipitation structures of Al-3Cu and Al-3Cu-1.78Mg (wt. % alloys at the early stages of elevated temperature aging. The Al-3Cu and Al-3Cu-1.78 Mg alloys were solution treated at 540 °C and 500 °C for 2 h, respectively, and then aged at 190 °C for 2 min. The precipitation structures in aged Al-3Cu-(1.78Mg alloys were characterized by Transmission Electron Microscopy (TEM and High Resolution Transmission Electron Microscopy (HTREM. 001 zone axis Selected area electron diffraction patterns indicate that L10 ordered structures are formed in the two aged alloys. HRTEM experiments reveal the partial dislocations on the interfaces of L10 ordered structures. From comparing experimental results with that in the literature, it is concluded that the L10 ordered structures in aged Al-3Cu alloy consist of Al and Cu atoms, and they are comprised by Al, Cu and Mg atoms together in the aged Al-3Cu-1.78Mg alloy. On the basis of precipitate growing thermodynamics, it is thought the L10 ordered structures act as nuclei for GP zones in Al-Cu-(Mg alloys during aging.En este trabajo se estudian las estructuras de precipitación en Al-3Cu y Al-3Cu-1,78Mg (% en peso en los estados iniciales de envejecimiento a temperatura elevada. Las aleaciones Al-3Cu y Al-3Cu-1.78 Mg fueron sometidas a un tratamiento térmico de solución de 2 h a 540 °C y 500 °C, respectivamente, y posteriormente envejecidas 2 min a 190 °C. Las estructuras de precipitación en Al-3Cu-(1.78Mg envejecido fueron caracterizadas por microscopía electrónica de transmisión (TEM y por microscopía electrónica de transmisión de alta resolución (HTREM. Los diagramas de difracción de electrones de área seleccionada indican que se forman estructuras ordenadas L10 en las dos aleaciones envejecidas. Experimentos de HRTEM revelan la presencia de dislocaciones parciales en las intercaras de las estructuras L10 ordenadas. Comparando estos resultados experimentales con la

Hardness and microstructure of Al-10.0 wt% Zn-4.0 wt% Mg alloy

International Nuclear Information System (INIS)

Iqbal, M.; Shaikh, M.A.; Ahmad, W.; Ali, K.L.

1996-01-01

Al-Zn-Mg alloys are widely used in industries as these have excellent physical and mechanical properties. However some aspects of the effect of heat treatment on these alloys are not yet clear. In order to understand the precipitation phenomena in these alloys, microstructure of a locally prepared alloy Al-10.0 wt% Zn-4.0 wt% Mg heat treated under different conditions has been examined in scanning electron microscope/electron probe micro analyser. Precipitates MgZn/sub 2/, MgZn/sub 4/ and Mg/sub 2/Zn/sub 11/ have been observed and these are caused by heat treatment. Correlation between these precipitates and Vickers's hardness has also been studied. In the present paper results of this investigation have been presented and discussed. (author)

COMPARISON OF HYDROCORTISONE 10 MG TABLETS: TABLET HARDNESS OPTIMISED FOR ADULT USE HAS NEGATIVE CONSEQUENCES FOR PAEDIATRIC USE.

Science.gov (United States)

Saimbi, Sarina; Madden, Valerie; Stirling, Heather; Yahyouche, Asma; Batchelor, Hannah

2016-09-01

Children's medicines are not always readily available as an age appropriate product and manipulation of adult products is often required. Recently the commercial manufacturing process for 10 mg hydrocortisone tablets has changed and the compression force increased due to tablets fracturing on removal from the blister pack. However, this change led to parents of children requiring hydrocortisone reporting that the tablets were more difficult to manipulate.This study evaluated 10 mg hydrocortisone tablets for their suitability for manipulation in order to deliver an appropriate dose to children (2 mg dose). The physical properties of tablets with the old and new compression force were compared as well as the accuracy of obtaining the paediatric dose. The tablets compared were hydrocortisone Auden 10 mg tablets (Brand A, PL16876/002)-these are the newer, harder tablets- and hydrocortisone 10 mg tablets (Brand B, PL17507/0097). Tablet physical properties including friability (Copley FRV200) and tablet hardness (Copley TBF1000) were compared. The accuracy of split doses (halve and quarter tablets) were recorded on a Sartorius analytical balance. The accuracy of the 2 mg paediatric dosing was assessed by crushing the tablet, adding 10 mL of water and extracting 2 mL. The concentration was measured using UV analysis (Jenway Genova Plus) according to a calibration curve (wavelength=246 nm). Two devices were used to crush the tablets: a spoon onto a plate and a commercially available crushing device (Apothecary Ezy Crush Pill Crusher With Ergo Grip). As anticipated Brand A tablets were harder (51.85 ±5.1 N) compared to Brand B (30.99±4.1 N). Brand A tablets passed the friability testing with Auden tablets which are known to be harder tablets and therefore more force is required to crush these. Some of the experimental work within this project was conducted by Andrew Hackett and Kameron Paul-Thaper whilst at the University of Birmingham on work

L10 ordered structures in Al-Cu-(Mg) alloys at the early stages of elevated temperature aging

Energy Technology Data Exchange (ETDEWEB)

Fuzhong, X.; Mingpu, W.

2016-07-01

This study concerns the precipitation structures of Al-3Cu and Al-3Cu-1.78Mg (wt. %) alloys at the early stages of elevated temperature aging. The Al-3Cu and Al-3Cu-1.78 Mg alloys were solution treated at 540 °C and 500 °C for 2 h, respectively, and then aged at 190 °C for 2 min. The precipitation structures in aged Al-3Cu-(1.78Mg) alloys were characterized by Transmission Electron Microscopy (TEM) and High Resolution Transmission Electron Microscopy (HTREM). 001 zone axis Selected area electron diffraction patterns indicate that L10 ordered structures are formed in the two aged alloys. HRTEM experiments reveal the partial dislocations on the interfaces of L10 ordered structures. From comparing experimental results with that in the literature, it is concluded that the L10 ordered structures in aged Al-3Cu alloy consist of Al and Cu atoms, and they are comprised by Al, Cu and Mg atoms together in the aged Al-3Cu-1.78Mg alloy. On the basis of precipitate growing thermodynamics, it is thought the L10 ordered structures act as nuclei for GP zones in Al-Cu-(Mg) alloys during aging. (Author)

L10 ordered structures in Al-Cu-(Mg) alloys at the early stages of elevated temperature aging

International Nuclear Information System (INIS)

Fuzhong, X.; Mingpu, W.

2016-01-01

This study concerns the precipitation structures of Al-3Cu and Al-3Cu-1.78Mg (wt. %) alloys at the early stages of elevated temperature aging. The Al-3Cu and Al-3Cu-1.78 Mg alloys were solution treated at 540 °C and 500 °C for 2 h, respectively, and then aged at 190 °C for 2 min. The precipitation structures in aged Al-3Cu-(1.78Mg) alloys were characterized by Transmission Electron Microscopy (TEM) and High Resolution Transmission Electron Microscopy (HTREM). 001 zone axis Selected area electron diffraction patterns indicate that L10 ordered structures are formed in the two aged alloys. HRTEM experiments reveal the partial dislocations on the interfaces of L10 ordered structures. From comparing experimental results with that in the literature, it is concluded that the L10 ordered structures in aged Al-3Cu alloy consist of Al and Cu atoms, and they are comprised by Al, Cu and Mg atoms together in the aged Al-3Cu-1.78Mg alloy. On the basis of precipitate growing thermodynamics, it is thought the L10 ordered structures act as nuclei for GP zones in Al-Cu-(Mg) alloys during aging. (Author)

The pregnancy outcome of progestin-primed ovarian stimulation using 4 versus 10 mg of medroxyprogesterone acetate per day in infertile women undergoing in vitro fertilisation: a randomised controlled trial.

Science.gov (United States)

Dong, J; Wang, Y; Chai, W R; Hong, Q Q; Wang, N L; Sun, L H; Long, H; Wang, L; Tian, H; Lyu, Q F; Lu, X F; Chen, Q J; Kuang, Y P

2017-06-01

To investigate the clinical outcome and endocrinological characteristics of progestin-primed ovarian stimulation (PPOS) using 4 versus 10 mg of medroxyprogesterone acetate (MPA) per day in infertile women with normal ovary reserve. A randomised parallel controlled trial. Tertiary-care academic medical centre. A cohort of 300 infertile women undergoing in vitro fertilisation (IVF)/intracytoplasmic sperm injection (ICSI) treatment. Human menopausal gonadotropin (hMG; 225 iu per day) and MPA (group A, 10 mg per day; group B, 4 mg per day) were started simultaneously from cycle day 3 onwards. Ovulation was co-triggered by human chorionic gonadotropin (hCG; 1000 iu) and gonadotropin-releasing hormone agonist (GnRH agonist; 0.1 mg) when dominant follicles matured. Viable embryos were cryopreserved for later frozen embryo transfer (FET) in both groups. The primary outcome measure was the number of oocytes retrieved. Secondary outcomes included the incidence of a premature surge in luteinising hormone (LH), the number of viable embryos, and clinical pregnancy outcomes. The number of oocytes retrieved and viable embryos were similar between two groups (9.8 ± 6.3 versus 9.6 ± 5.9; 4.2 ± 2.6 versus 3.7 ± 3.0; P > 0.05). No significant difference was found in clinical pregnancy rate (58.0 versus 48.7%) and live birth rate per participant (48.7 versus 42.0%; P > 0.05). No premature LH surge and ovarian hyperstimulation syndrome (OHSS) occurred in either group. Progestin-primed ovarian stimulation (PPOS) using 4 or 10 mg of MPA per day was comparable in terms of the number of oocytes retrieved and pregnancy outcome after FET. The administration of 4 mg of MPA per day was sufficient to prevent an untimely LH rise in women undergoing IVF/ICSI treatment. An RCT confirmed similar pregnancy outcome in P-primed ovarian stimulation with a daily dose of 4 or 10 mg MPA. © 2017 Royal College of Obstetricians and Gynaecologists.

Lightweight MgB2 superconducting 10 MW wind generator

Science.gov (United States)

Marino, I.; Pujana, A.; Sarmiento, G.; Sanz, S.; Merino, J. M.; Tropeano, M.; Sun, J.; Canosa, T.

2016-02-01

The offshore wind market demands a higher power rate and more reliable turbines in order to optimize capital and operational costs. The state-of-the-art shows that both geared and direct-drive conventional generators are difficult to scale up to 10 MW and beyond due to their huge size and weight. Superconducting direct-drive wind generators are considered a promising solution to achieve lighter weight machines. This work presents an innovative 10 MW 8.1 rpm direct-drive partial superconducting generator using MgB2 wire for the field coils. It has a warm iron rotor configuration with the superconducting coils working at 20 K while the rotor core and the armature are at ambient temperature. A cooling system based on cryocoolers installed in the rotor extracts the heat from the superconducting coils by conduction. The generator's main parameters are compared against a permanent magnet reference machine, showing a significant weight and size reduction. The 10 MW superconducting generator concept will be experimentally validated with a small-scale magnetic machine, which has innovative components such as superconducting coils, modular cryostats and cooling systems, and will have similar size and characteristics as the 10 MW generator.

Influence of Iron in AlSi10MgMn Alloy

Directory of Open Access Journals (Sweden)

Žihalová M.

2014-12-01

Full Text Available Presence of iron in Al-Si cast alloys is common problem mainly in secondary (recycled aluminium alloys. Better understanding of iron influence in this kind of alloys can lead to reduction of final castings cost. Presented article deals with examination of detrimental iron effect in AlSi10MgMn cast alloy. Microstructural analysis and ultimate tensile strength testing were used to consider influence of iron to microstructure and mechanical properties of selected alloy.

Experimental Research on Selective Laser Melting AlSi10Mg Alloys: Process, Densification and Performance

Science.gov (United States)

Chen, Zhen; Wei, Zhengying; Wei, Pei; Chen, Shenggui; Lu, Bingheng; Du, Jun; Li, Junfeng; Zhang, Shuzhe

2017-12-01

In this work, a set of experiments was designed to investigate the effect of process parameters on the relative density of the AlSi10Mg parts manufactured by SLM. The influence of laser scan speed v, laser power P and hatch space H, which were considered as the dominant parameters, on the powder melting and densification behavior was also studied experimentally. In addition, the laser energy density was introduced to evaluate the combined effect of the above dominant parameters, so as to control the SLM process integrally. As a result, a high relative density (> 97%) was obtained by SLM at an optimized laser energy density of 3.5-5.5 J/mm2. Moreover, a parameter-densification map was established to visually select the optimum process parameters for the SLM-processed AlSi10Mg parts with elevated density and required mechanical properties. The results provide an important experimental guidance for obtaining AlSi10Mg components with full density and gradient functional porosity by SLM.

Lightweight MgB2 superconducting 10 MW wind generator

International Nuclear Information System (INIS)

Marino, I; Pujana, A; Sarmiento, G; Sanz, S; Merino, J M; Tropeano, M; Sun, J; Canosa, T

2016-01-01

The offshore wind market demands a higher power rate and more reliable turbines in order to optimize capital and operational costs. The state-of-the-art shows that both geared and direct-drive conventional generators are difficult to scale up to 10 MW and beyond due to their huge size and weight. Superconducting direct-drive wind generators are considered a promising solution to achieve lighter weight machines. This work presents an innovative 10 MW 8.1 rpm direct-drive partial superconducting generator using MgB 2 wire for the field coils. It has a warm iron rotor configuration with the superconducting coils working at 20 K while the rotor core and the armature are at ambient temperature. A cooling system based on cryocoolers installed in the rotor extracts the heat from the superconducting coils by conduction. The generator’s main parameters are compared against a permanent magnet reference machine, showing a significant weight and size reduction. The 10 MW superconducting generator concept will be experimentally validated with a small-scale magnetic machine, which has innovative components such as superconducting coils, modular cryostats and cooling systems, and will have similar size and characteristics as the 10 MW generator. (paper)

Homoepitaxial nonpolar (10-10) ZnO/ZnMgO monolithic microcavities: Towards reduced photonic disorder

International Nuclear Information System (INIS)

Zuniga-Perez, J.; Kappei, L.; Deparis, C.; Chenot, S.; Leroux, M.; Reveret, F.; Jamadi, O.; Leymarie, J.; Grundmann, M.; Prado, E. de

2016-01-01

Nonpolar ZnO/ZnMgO-based optical microcavities have been grown on (10-10) m-plane ZnO substrates by plasma-assisted molecular beam epitaxy. Reflectivity measurements indicate an exponential increase of the cavity quality factor with the number of layers in the distributed Bragg reflectors. Most importantly, microreflectivity spectra recorded with a spot size in the order of 2 μm show a negligible photonic disorder (well below 1 meV), leading to local quality factors equivalent to those obtained by macroreflectivity. The anisotropic character of the nonpolar heterostructures manifests itself both in the surface features, elongated parallel to the in-plane c direction, and in the optical spectra, with two cavity modes being observed at different energies for orthogonal polarizations.

Homoepitaxial nonpolar (10-10) ZnO/ZnMgO monolithic microcavities: Towards reduced photonic disorder

Energy Technology Data Exchange (ETDEWEB)

Zuniga-Perez, J., E-mail: jzp@crhea.cnrs.fr; Kappei, L.; Deparis, C.; Chenot, S.; Leroux, M. [CRHEA-CNRS, Rue Bernard Gregory, 06560 Valbonne (France); Reveret, F.; Jamadi, O.; Leymarie, J. [Clermont Université, Institut Pascal (IP), BP 10448, F-63000 Clermont-Ferrand (France); CNRS, UMR 6602, IP, F-63171 Aubière (France); Grundmann, M. [CRHEA-CNRS, Rue Bernard Gregory, 06560 Valbonne (France); Institut für Experimentelle Physik II, Fakultät für Physik und Geowissenschaften, Universität Leipzig, Linnestr. 5, 04103 Leipzig (Germany); Prado, E. de [CRHEA-CNRS, Rue Bernard Gregory, 06560 Valbonne (France); Departamento de Física Aplicada y Electromagnetismo, Universitat de Valencia, c/Dr Moliner 50, Burjassot, Valencia 46100 (Spain)

2016-06-20

Nonpolar ZnO/ZnMgO-based optical microcavities have been grown on (10-10) m-plane ZnO substrates by plasma-assisted molecular beam epitaxy. Reflectivity measurements indicate an exponential increase of the cavity quality factor with the number of layers in the distributed Bragg reflectors. Most importantly, microreflectivity spectra recorded with a spot size in the order of 2 μm show a negligible photonic disorder (well below 1 meV), leading to local quality factors equivalent to those obtained by macroreflectivity. The anisotropic character of the nonpolar heterostructures manifests itself both in the surface features, elongated parallel to the in-plane c direction, and in the optical spectra, with two cavity modes being observed at different energies for orthogonal polarizations.

The transient M/G/1/0 queue: some bounds and approximations for light traffic with application to reliability

Directory of Open Access Journals (Sweden)

J. Ben Atkinson

1995-01-01

Full Text Available We consider the transient analysis of the M/G/1/0 queue, for which Pn(t denotes the probability that there are no customers in the system at time t, given that there are n(n=0,1 customers in the system at time 0. The analysis, which is based upon coupling theory, leads to simple bounds on Pn(t for the M/G/1/0 and M/PH/1/0 queues and improved bounds for the special case M/Er/1/0. Numerical results are presented for various values of the mean arrival rate λ to demonstrate the increasing accuracy of approximations based upon the above bounds in light traffic, i.e., as λ→0. An important area of application for the M/G/1/0 queue is as a reliability model for a single repairable component. Since most practical reliability problems have λ values that are small relative to the mean service rate, the approximations are potentially useful in that context. A duality relation between the M/G/1/0 and GI/M/1/0 queues is also described.

Patch testing with 2.0% (0.60 mg/cm2) formaldehyde instead of 1.0% (0.30 mg/cm2) detects significantly more contact allerg

DEFF Research Database (Denmark)

Pontén, Ann; Aalto-Korte, Kristiina; Agner, Tove

2013-01-01

.To validate earlier patch test results for comparison of 1% (wt/vol) and 2% (wt/vol) formaldehyde in water, and to investigate co-reactivity with quaternium-15. Materials and methods.In 12 dermatology clinics, 3591 patients were routinely patch tested simultaneously with 2.0% (wt/vol) (0.60 mg/cm(2) ) and 1.......0% (wt/vol) (0.30 mg/cm(2) ) formaldehyde. Micropipettes were used for delivering the exact dosage of the allergen. Results.Significantly more patients reacted to 2.0% formaldehyde than to 1.0% (3.4% versus 1.8%, p

Effect of microwave irradiation on hydrogen sorption properties of hand mixed MgH{sub 2} – 10 wt.% carbon fibers

Energy Technology Data Exchange (ETDEWEB)

Awad, A.S. [Université de Bordeaux, ICMCB-CNRS, 87 Avenue du Dr Schweitzer, F-33600 Pessac (France); LCPM/PR2N, Université Libanaise, Faculté des Sciences 2, 90656 Jdeidet El Matn (Lebanon); Nakhl, M.; Zakhour, M. [LCPM/PR2N, Université Libanaise, Faculté des Sciences 2, 90656 Jdeidet El Matn (Lebanon); Santos, S.F.; Souza, F.L. [Universidade Federal do ABC, Avenida dos Estados 5001, 09210-580 Santo André – SP (Brazil); Bobet, J.-L., E-mail: jean-louis.bobet@u-bordeaux.fr [Université de Bordeaux, ICMCB-CNRS, 87 Avenue du Dr Schweitzer, F-33600 Pessac (France)

2016-08-15

The effect of microwave (MW) irradiation on the hydrogen sorption properties of magnesium powder is explored in the present work. MgH{sub 2} – 10 wt.% CFs (CFs = Carbons Fibers) was prepared by hand mixing, dehydrogenated under microwave irradiation for 20 s and then hydrogenated/dehydrogenated at about 300 °C – 1 MPa and 330 °C–0.03 MPa to investigate the effect of microwave irradiation on the solid/gas sorption properties. It has to be noted that the hydrogen absorption capacity and sorption kinetics of the MgH{sub 2} – 10 wt.% CFs mixture increased after dehydriding under MW irradiation. The MgH{sub 2} – 10 wt.% CFs mixture dehydrogenated by microwave irradiation can absorb about 5.8 wt.% and 5.3 wt.% H at 330 and 300 °C, respectively, within 2 h while the as-prepared MgH{sub 2} – 10 wt.% CFs mixture absorb only 4.6 wt.% H within the same duration. It is also demonstrated that MgH{sub 2} – 10 wt.% CFs mixture dehydrogenated by microwave irradiation exhibited good hydrogen desorption properties and, as an example, a microwave irradiated sample could release 5.8 wt.% H within 1 h at 330 °C in comparison to the as-prepared MgH{sub 2} – 10 wt.% CFs mixture which desorbed 4.4 wt.% H within 3 h. Scanning electron microscopy (SEM) images revealed that the particle sizes of the MW dehydrogenated mixture decreased after several solid/gas sorption cycles. This contribute to the improvement of hydrogen storage properties of the microwaves dehydrogenated MgH{sub 2} – 10 wt.% CFs mixture. In addition, the hydrogenated MgH{sub 2} – 10 wt.% CFs mixture show reproducible and better microwave-assisted dehydriding reaction during second microwaves cycle. - Highlights: • Dehydriding reaction of MgH{sub 2} by microwave method. • Effect of microwaves treatment on the hydrogen sorption properties of Mg. • Effect of discontinuous microwaves irradiation.

Tribological Behavior of Aluminum Alloy AlSi10Mg-TiB2 Composites Produced by Direct Metal Laser Sintering (DMLS)

Science.gov (United States)

Lorusso, Massimo; Aversa, Alberta; Manfredi, Diego; Calignano, Flaviana; Ambrosio, Elisa Paola; Ugues, Daniele; Pavese, Matteo

2016-08-01

Direct metal laser sintering (DMLS) is an additive manufacturing technique for the production of parts with complex geometry and it is especially appropriate for structural applications in aircraft and automotive industries. Aluminum-based metal matrix composites (MMCs) are promising materials for these applications because they are lightweight, ductile, and have a good strength-to-weight ratio This paper presents an investigation of microstructure, hardness, and tribological properties of AlSi10Mg alloy and AlSi10Mg alloy/TiB2 composites prepared by DMLS. MMCs were realized with two different compositions: 10% wt. of microsize TiB2, 1% wt. of nanosize TiB2. Wear tests were performed using a pin-on-disk apparatus on the prepared samples. Performances of AlSi10Mg samples manufactured by DMLS were also compared with the results obtained on AlSi10Mg alloy samples made by casting. It was found that the composites displayed a lower coefficient of friction (COF), but in the case of microsize TiB2 reinforcement the wear rate was higher than with nanosize reinforcements and aluminum alloy without reinforcement. AlSi10Mg obtained by DMLS showed a higher COF than AlSi10Mg obtained by casting, but the wear rate was higher in the latter case.

Safety and efficacy of fixed-dose 10 mg daily isotretinoin treatment for acne vulgaris in Malaysia.

Science.gov (United States)

Yap, Felix Boon-Bin

2017-09-01

Low-dose isotretinoin is used to reduce side effects albeit higher relapse. This study aimed to determine the efficacy and safety of fixed-dose 10 mg daily isotretinoin for the treatment of acne. This prospective study was performed between 2011 and 2015. All 150 patients were given 10 mg daily isotretinoin until a cumulative dose of 90-110 mg/kg. The mean age was 26.6 years with 64.7% moderate acne, 29.3% severe, and 6% very severe. The mean cumulative dose was 98.8 ± 6.05 mg/kg. All 150 patients had total clearance with a mean time to clearance of 24.0 weeks. Patients with severe/very severe acne had higher cumulative dosage (102.1 vs. 97.0, P < 0.001) and longer duration to clearance (32.9 weeks vs. 19.1 weeks, P < 0.001). Mild relapse was seen in 4%. The mean time to relapse was 32.3 weeks. Lip dryness was the commonest side effects (100%). Mild transient elevation of liver enzymes was detected in 3.3% and a slight increase of serum lipid in 2.7% with no treatment discontinuation. Fixed-dose 10 mg daily treatment with isotretinoin until a cumulative dose of 90-110 mg/kg is safe with low relapse rate. © 2016 Wiley Periodicals, Inc.

Application of Al-2La-1B Grain Refiner to Al-10Si-0.3Mg Casting Alloy

Science.gov (United States)

Jing, Lijun; Pan, Ye; Lu, Tao; Li, Chenlin; Pi, Jinhong; Sheng, Ningyue

2018-05-01

This paper reports the application and microstructure refining effect of an Al-2La-1B grain refiner in Al-10Si-0.3Mg casting alloy. Compared with the traditional Al-5Ti-1B refiner, Al-2La-1B refiner shows better performances on the grain refinement of Al-10Si-0.3Mg alloy. Transmission electron microscopy analysis suggests that the crystallite structure features of LaB6 are beneficial to the heterogeneous nucleation of α-Al grains. Regarding the mechanical performances, tensile properties of Al-10Si-0.3Mg casting alloy are prominently improved, due to the refined microstructures.

Synthesis, crystal growth and structure of Mg containing β-rhombohedral boron: MgB17.4

International Nuclear Information System (INIS)

Adasch, Volker; Hess, Kai-Uwe; Ludwig, Thilo; Vojteer, Natascha; Hillebrecht, Harald

2006-01-01

For the first time, single crystals of Mg containing β-rhombohedral boron MgB 17.4 were synthesised from the elements in a Mg/Cu melt at 1600deg. C. The crystal structure determined by the refinement of single crystal data (space group R-3m, a=10.991(2)A, c=24.161(4)A, 890 reflections, 123 variables, R 1 (F)=0.049, wR 2 (I)=0.122) improves and modifies the former structure model derived from earlier investigations on powder samples. Mg is located on four different positions with partial occupation. While the occupation of the sites D (53.3%), E (91%) and F (7.2%) is already known from other boron-rich borides related to β-rhombohedral boron, the occupation of the fourth position (18h, 6.7%) is observed for the first time. Two boron positions show partial occupation. The summation reveals the composition MgB 17.4 and Mg 5.85 B 101.9 , respectively, confirmed by WDX measurements. The single crystals of MgB 17.4 show the highest Mg content ever found. Preliminary measurements indicate no superconductivity

Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation

Energy Technology Data Exchange (ETDEWEB)

Martinez Sanchez, Adela H., E-mail: adela.martinez@hzg.de [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany); Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany); Weinberg, Annelie [Department of Orthopedics and Orthopedic Surgery, Medical University of Graz (Austria); Luthringer, Bérengère J.C. [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany)

2017-03-01

Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10 wt% of gadolinium (Mg-10Gd) and Mg with 2 wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7 days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. - Highlights: • Degradation of PMg, and Mg-2Ag do not influence ATDC5 cells growth and chondrogenic redifferentiation. • Mg-10Gd enhances fast chondrogenic redifferentiation and expression of hyperthrophic markers on ATDC5 cells. • Further evaluation of the effects of PMg, Mg-10Gd and Mg-2Ag in vivo are necessary to confirm its potential for application in growing bones.

Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation

International Nuclear Information System (INIS)

Martinez Sanchez, Adela H.; Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine; Weinberg, Annelie; Luthringer, Bérengère J.C.

2017-01-01

Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10 wt% of gadolinium (Mg-10Gd) and Mg with 2 wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7 days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. - Highlights: • Degradation of PMg, and Mg-2Ag do not influence ATDC5 cells growth and chondrogenic redifferentiation. • Mg-10Gd enhances fast chondrogenic redifferentiation and expression of hyperthrophic markers on ATDC5 cells. • Further evaluation of the effects of PMg, Mg-10Gd and Mg-2Ag in vivo are necessary to confirm its potential for application in growing bones.

Element distribution in the corrosion layer and cytotoxicity of alloy Mg-10Dy during in vitro biodegradation.

Science.gov (United States)

Yang, Lei; Hort, Norbert; Laipple, Daniel; Höche, Daniel; Huang, Yuanding; Kainer, Karl Ulrich; Willumeit, Regine; Feyerabend, Frank

2013-11-01

The present work investigates the corrosion behaviour, the element distribution in the corrosion layer and the cytocompatibility of alloy Mg-10Dy. The corrosion experiments were performed in a cell culture medium (CCM) under cell culture conditions close to the in vivo environment. The element distribution on the surface as well as in cross-sections of the corrosion layer was investigated using scanning electron microscopy, energy-dispersive X-ray analysis, X-ray photoelectron spectroscopy and X-ray diffraction. The cytocompatibility of alloy Mg-10Dy with primary human osteoblasts was evaluated by MTT, cell adhesion and live/dead staining tests. The results show that the corrosion layer was enriched in Dy, while the P and Ca content gradually decreased from the surface to the bottom of the corrosion layer. In addition, large amounts of MgCO3·3H2O formed in the corrosion layer after 28 days immersion. Both extracts and the Dy-enriched corrosion layer of alloy Mg-10Dy showed no cytotoxicity to primary human osteoblasts. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Exploratory pilot study assessing the risk of cognitive impairment or sedation in the elderly following single doses of solifenacin 10 mg.

Science.gov (United States)

Wesnes, Keith A; Edgar, Chris; Tretter, Reiner N; Bolodeoku, John

2009-11-01

To assess the cognitive effects of single doses of solifenacin 10 mg compared with placebo (primary objective) and oxybutynin immediate release (IR) 10 mg (secondary objective) in elderly subjects. Single-centre, randomised, double-blind, placebo-controlled study in 12 healthy elderly volunteers, with three crossover periods separated by two 14-day washout periods. Each sequence consisted of a single dose of solifenacin 10 mg in one period, oxybutynin IR 10 mg in another and placebo in another. Aspects of attention, information processing, working memory, episodic memory and self-rated mood and alertness were tested using the validated Cognitive Drug Research computerised assessment system. There was no evidence from absolute mean values or changes from baseline to suggest that solifenacin 10 mg impaired cognition or self-ratings of mood and alertness versus placebo. Post-hoc ANCOVA showed no statistically significant cognitive deterioration with solifenacin versus placebo, when measured at a time point closest to the probable C(max) of solifenacin. Oxybutynin was associated with statistically significant impairments in several measures of cognitive function at a time point corresponding with its probable C(max). In this pilot study, single 10 mg doses of solifenacin did not show any clear propensity to impair cognitive function in a healthy elderly population.

Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation.

Science.gov (United States)

Martinez Sanchez, Adela H; Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine; Weinberg, Annelie; Luthringer, Bérengère J C

2017-03-01

Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10wt% of gadolinium (Mg-10Gd) and Mg with 2wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. Copyright © 2016 Elsevier B.V. All rights reserved.

Microstructure and Properties of AlSi10Mg Powder for Selective Laser Melting

Directory of Open Access Journals (Sweden)

TANG Pengjun

2018-02-01

Full Text Available The AlSi10Mg powder was prepared by supersonic gas atomization. After classified, the powder was fabricated into block by selective laser melting (SLM. The microstructure, phase, and evolutions of powder and block were investigated by optical microscope, scanning electron microscope and X-Ray Diffraction. The tensile properties of SLM block were tested by tensile experiments at room temperature. The results show that the size distribution of AlSi10Mg powder after classified can meet the requirements of SLM technology. The powder always is spherical and spherical-like. Meanwhile, the microstructure of powders is fine and uniform, which contain α(Al matrix and (α+Si eutectic. In addition, the melt pool boundaries of SLM block are legible. The microstructure is also uniform and densified, the relative density approaches to 99.5%. On the other hand, only α(Al and few Silicon phase are detected in this condition, due to the most alloying elements are dissolved in α(Al matrix. At room temperature, the ultimate tensile strength of SLM block reaches up to 442 MPa.

Sr-Nd-Hf Isotopic Analysis of <10 mg Dust Samples: Implications for Ice Core Dust Source Fingerprinting

DEFF Research Database (Denmark)

Ujvari, Gabor; Wegner, Wencke; Klötzli, Urs

2018-01-01

Combined Sr‐Nd‐Hf isotopic data of two reference materials (AGV‐1/BCR2) and 50, 10, and 5 mg aliquots of carbonate‐free fine grain (isotopic...... compositions (ICs) demonstrate that robust isotopic ratios can be obtained from 5 to 10 mg size rock samples using the ion exchange/mass spectrometry techniques applied. While 87Sr/86Sr ratios of dust aluminosilicate fractions are affected by even small changes in pretreatments, Nd isotopic ratios are found...... to be insensitive to acid leaching, grain‐size or weathering effects. However, the Nd isotopic tracer is sometimes inconclusive in dust source fingerprinting (BEI and NUS both close to ɛNd(0) –10). Hafnium isotopic values (

Protective Effect of Coenzyme Q10 on Methamphetamine-Induced Apoptosis in Adult Male Rats

Directory of Open Access Journals (Sweden)

Fatemeh Gholipour

2017-06-01

Full Text Available Background: The negative consequence of methamphetamine abuse is due to neuropathologic changes in the brain, which reduces dopaminergic neurons and result in damage to different brain areas. Neurotoxicity induced by methamphetamine increases the oxidative stress and associated with neuronal apoptosis. The role of the antioxidant coenzyme Q10 probably produces its neuroprotective effects. Therefore, the purpose of the present study was to examine the protective effect of coenzyme Q10 on methamphetamine-induced apoptosis in adult male rats.Materials and Methods: Fifty Wistar eight-week adult rats randomly divided into 5 groups: Healthy control, methamphetamine injection (Meth, methamphetamine injection and CoQ10 5mg/kg treatment (Meth+Post CoQ10 5mg/kg, methamphetamine injection and CoQ10 10mg/kg treatment (Meth+Post CoQ10 10mg/kg, methamphetamine injection and CoQ10 20mg/kg treatment (Meth+Post CoQ10 20mg/kg. Methamphetamine with a purity of 96% with a dosage of 20 mg/kg was injected Intraperitoneal. Coenzyme Q10 for three treatment groups was injected intraperitoneally for 14 days in a dosage of 5, 10 and 20 mg/kg/day. The protein expressions of Baxand Bcl2 were evaluated by western blotting technique.Results: Bax protein expression was significantly lower in Meth+Post CoQ10 5mg/kg (p=0.010 and so Meth+Post CoQ10 10mg/kg (p=0.004 comparing to Meth group. In addition, Bcl2 protein expression was significantly higher in Meth+Post CoQ10 5mg/kg comparing to Meth group (p=0.018. However, there were no significant differences between control and CoQ10 treatment groups. Bax/Bcl2 ratio was significantly lower in Meth+Post CoQ10 5mg/kg (p=0.005, Meth+Post CoQ10 10mg/kg (p=0.008 and Meth+Post CoQ10 20mg/kg (p=0.044 comparing to Meth group.Conclusion: We suggest that CoQ10 reduces the methamphetamine-induced apoptosis in the striatum of the rats through the reduction of apoptotic factors and increase of anti-apoptotic pathways.

Effect of the third element on the structure of liquid Mg{sub 65}Cu{sub 25}Y{sub 10} alloy

Energy Technology Data Exchange (ETDEWEB)

Liu, Dan [Key Laboratory for Liquid–Solid Structural Evolution and Processing of Materials (Ministry of Education), Shandong University, Jinan 250061 (China); Weihai Wanfeng Magnesium Industry Science and Technology Development Co. Ltd., Weihai 264209 (China); Zhu, Xun Ming [Weihai Wanfeng Magnesium Industry Science and Technology Development Co. Ltd., Weihai 264209 (China); Qin, Jing Yu, E-mail: qinjy@sdu.edu.cn [Key Laboratory for Liquid–Solid Structural Evolution and Processing of Materials (Ministry of Education), Shandong University, Jinan 250061 (China); Duan, Jun Peng; Wang, Ai Min [Weihai Wanfeng Magnesium Industry Science and Technology Development Co. Ltd., Weihai 264209 (China); Gu, Ting Kun [School of Electrical Engineering, Shandong University, Jinan 250061 (China)

2016-08-12

The liquid structures of Mg{sub 65}Cu{sub 25}Y{sub 10} and its three homologous binary liquid alloys are investigated via ab initio molecular dynamics in the present work. The chemical and topological environments in all four liquid alloys are analyzed using pair distribution function, coordination number, and the Voronoi polyhedron. It shows that the Cu atoms play significant role in deciding the chemical and topological short-range orders of the Mg{sub 65}Cu{sub 25}Y{sub 10} liquid alloy. The Voronoi polyhedra in the ternary liquid alloy illustrate less varieties and longer lifetime. Moreover, the diffusion coefficients are decreased significantly in the ternary liquid alloys according to the mean square displacements. All above offer a deeper insight into how the three species work in the Mg{sub 65}Cu{sub 25}Y{sub 10} liquid alloy. - Highlights: • Cu plays crucial role in Mg{sub 65}Cu{sub 25}Y{sub 10}'s chemical and topological SROs. • Additive elements decrease varieties and prolong lifetimes of Voronoi polyhedra. • Additive elements hinder the diffusion of Mg and Y efficiently.

Electromagnetic and microwave absorption properties of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19}

Energy Technology Data Exchange (ETDEWEB)

Chen, Jing [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Meng, Pingyuan [Huzhou Innovation Center of Advanced Materials, Shanghai Institute of Ceramics Chinese Academy of Sciences, Huzhou 215100 (China); Wang, Meiling [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Zhou, Guanchen [School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Wang, Xinqing [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Xu, Guangliang, E-mail: xuguangliang@swust.edu.cn [School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China)

2016-09-15

To improve the impedance matching and then achieve a better microwave absorption performance in electromagnetic absorber, the Mg{sup 2+} was added to occupy the sites of Co{sup 2+} in hexagonal-type ferrite BaCoTiFe{sub 10}O{sub 19}. BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} were synthesized by a simple sol-gel combustion technique and the phase of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} was confirmed by X-ray diffraction analysis (XRD). The grain size of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} was in the range of 100–400 nm and crystal particles were refined with the augment of doped Mg{sup 2+}. Based on the static magnetic measurement, the coercivity (H{sub c}) increased and the saturation magnetization (M{sub s}) decreased as the x increased. Moreover, it was found that BaMg{sub 0.4}Co{sub 0.6}TiFe{sub 10}O{sub 19} possessed a maximum reflection loss of −33.7 dB with a matching thickness of 2.0 mm measured by the vector net-analyzer in the frequency of 0.5–18 GHz, which also had a bandwidth below −20 dB ranging from 11.5 GHz to 17.2 GHz. Meanwhile, the permeability of the prepared ferrites could be adjusted and a proper match was provided between dielectric and magnetic properties by controlling the doped content of Mg{sup 2+}, which would be significant to the application of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} in the field of the microwave absorbing materials. - Highlights: • The Mg{sup 2+} ions were first employed to occupy the place of Co{sup 2+} ions in BaCoTiFe{sub 10}O{sub 19}. • The grains were refined as Co substitution by Mg in ferrite. • The peaks of complex permeability shift to high frequency with Mg{sup 2+} substituted. • The coercivity increased and saturation magnetization slightly decreased. • Substitution of Mg{sup 2+} enhanced microwave absorption and broadened bandwidth.

AKR1B10 induces cell resistance to daunorubicin and idarubicin by reducing C13 ketonic group

International Nuclear Information System (INIS)

Zhong Linlin; Shen Honglin; Huang Chenfei; Jing, Hongwu; Cao Deliang

2011-01-01

Daunorubicin, idarubicin, doxorubicin and epirubicin are anthracyclines widely used for the treatment of lymphoma, leukemia, and breast, lung, and liver cancers, but tumor resistance limits their clinical success. Aldo-keto reductase family 1 B10 (AKR1B10) is an NADPH-dependent enzyme overexpressed in liver and lung carcinomas. This study was aimed to determine the role of AKR1B10 in tumor resistance to anthracyclines. AKR1B10 activity toward anthracyclines was measured using recombinant protein. Cell resistance to anthracycline was determined by ectopic expression of AKR1B10 or inhibition by epalrestat. Results showed that AKR1B10 reduces C13-ketonic group on side chain of daunorubicin and idarubicin to hydroxyl forms. In vitro, AKR1B10 converted daunorubicin to daunorubicinol at V max of 837.42 ± 81.39 nmol/mg/min, K m of 9.317 ± 2.25 mM and k cat /K m of 3.24. AKR1B10 showed better catalytic efficiency toward idarubicin with V max at 460.23 ± 28.12 nmol/mg/min, K m at 0.461 ± 0.09 mM and k cat /K m at 35.94. AKR1B10 was less active toward doxorubicin and epirubicin with a C14-hydroxyl group. In living cells, AKR1B10 efficiently catalyzed reduction of daunorubicin (50 nM) and idarubicin (30 nM) to corresponding alcohols. Within 24 h, approximately 20 ± 2.7% of daunorubicin (1 μM) or 23 ± 2.3% of idarubicin (1 μM) was converted to daunorubicinol or idarubicinol in AKR1B10 expression cells compared to 7 ± 0.9% and 5 ± 1.5% in vector control. AKR1B10 expression led to cell resistance to daunorubicin and idarubicin, but inhibitor epalrestat showed a synergistic role with these agents. Together our data suggest that AKR1B10 participates in cellular metabolism of daunorubicin and idarubicin, resulting in drug resistance. These data are informative for the clinical use of idarubicin and daunorubicin. - Highlights: → This study defines enzyme activity of AKR1B10 protein towards daunorubicin, idarubicin, doxorubicin, and epirubicin. → This study pinpoints

The maize CorA/MRS2/MGT-type Mg transporter, ZmMGT10, responses to magnesium deficiency and confers low magnesium tolerance in transgenic Arabidopsis.

Science.gov (United States)

Li, Hongyou; Wang, Ning; Ding, Jianzhou; Liu, Chan; Du, Hanmei; Huang, Kaifeng; Cao, Moju; Lu, Yanli; Gao, Shibin; Zhang, Suzhi

2017-10-01

ZmMGT10 was specifically expressed in maize roots and induced by a deficiency of magnesium. Overexpression of ZmMGT10 restored growth deficiency of the Salmonella typhimurium MM281 strain and enhanced the tolerance in Arabidopsis to stress induced by low magnesium levels by increasing uptake of Mg 2+ via roots. CorA/MRS2/MGT-type Mg 2+ transporters play a significant role in maintaining magnesium (Mg) homeostasis in plants. Although the maize CorA/MRS2/MGT family comprises of 12 members, currently no member has been functionally characterized. Here, we report the isolation and functional characterization of ZmMGT10 from the maize MRS2/MGT gene family. ZmMGT10 has a typical structure feature which includes two conserved TMs near the C-terminal end and an altered AMN tripeptide motif. The high sequence similarity and close phylogenetic relationship indicates that ZmMGT10 is probably the counterpart of Arabidopsis AtMGT6. The complementation of the Salmonella typhimurium mutated MM281 strain indicates that ZmMGT10 possesses the ability to transport Mg 2+ . ZmMGT10 was specifically expressed in the plant roots and it can be stimulated by a deficiency of Mg. Transgenic Arabidopsis plants which overexpressed ZmMGT10 grew more vigorously than wild-type plants under low Mg conditions, exhibited by longer root length, higher plant fresh weight and chlorophyll content, suggesting ZmMGT10 was essential for plant growth and development under low Mg conditions. Further investigations found that high accumulation of Mg 2+ occurred in transgenic plants attributed to improved Mg 2+ uptake and thereby enhanced tolerance to Mg deficiency. Results from this investigation illustrate that ZmMGT10 is a Mg transporter of maize which can enhance the tolerance to Mg deficient conditions by improving Mg 2+ uptake in the transgenic plants of Arabidopsis.

Comparison of the efficacy and safety of rosuvastatin 10 mg and atorvastatin 20 mg in high-risk patients with hypercholesterolemia – Prospective study to evaluate the Use of Low doses of the Statins Atorvastatin and Rosuvastatin (PULSAR

Directory of Open Access Journals (Sweden)

García Hugo

2006-12-01

Full Text Available Abstract Background Many patients at high risk of cardiovascular disease do not achieve recommended low-density lipoprotein cholesterol (LDL-C goals. This study compared the efficacy and safety of low doses of rosuvastatin (10 mg and atorvastatin (20 mg in high-risk patients with hypercholesterolemia. Methods A total of 996 patients with hypercholesterolemia (LDL-C ≥ 3.4 and Results Rosuvastatin 10 mg reduced LDL-C levels significantly more than atorvastatin 20 mg at week 6 (44.6% vs. 42.7%, p Conclusion In high-risk patients with hypercholesterolemia, rosuvastatin 10 mg was more efficacious than atorvastatin 20 mg at reducing LDL-C, enabling LDL-C goal achievement and improving other lipid parameters. Both treatments were well tolerated.

The Activity Support Scale for Multiple Groups (ACTS-MG): Child-reported Physical Activity Parenting in African American and Non-Hispanic White Families.

Science.gov (United States)

Lampard, Amy M; Nishi, Akihiro; Baskin, Monica L; Carson, Tiffany L; Davison, Kirsten K

2016-01-01

This study aimed to assess the psychometric properties of a child-report, multidimensional measure of physical activity (PA) parenting, the Activity Support Scale for Multiple Groups (ACTS-MG), in African American and non-Hispanic white families. The ACTS-MG was administered to children aged 5 to 12 years. A three factor model of PA parenting (Modeling of PA, Logistic Support, and Restricting Access to Screen-based Activities) was tested separately for mother's and fathers' PA parenting. The proposed three-factor structure was supported in both racial groups for mothers' PA parenting and in the African American sample for fathers' PA parenting. Factorial invariance between racial groups was demonstrated for mother's PA parenting. Building on a previous study examining the ACTS-MG parent-report, this study supports the use of the ACTS-MG child-report for mothers' PA parenting. However, further research is required to investigate the measurement of fathers' PA parenting across racial groups.

Perbandingan Gabapentin 600 mg dengan 1.200 mg per Oral Preoperatif terhadap Nilai Visual Analogue Scale dan Pengurangan Kebutuhan Petidin Pascaoperasi pada Modifikasi Mastektomi Radikal

Directory of Open Access Journals (Sweden)

Ardi Zulfariansyah

2013-12-01

Full Text Available Gabapentin is a GABA analog which has the effect of anti hyperalgesia, anti allodynia, and anti nociceptive. This research was conducted in order to assess the effect of 600mg and 1,200 mg gabapentin given preoperatively to assess visual analogue scale (VAS score and reduction of pethidine requirement. The study was done by conducting a double blind randomized controlled trial on 38 patients, aged 18–65 years, with ASA physical status I–II. Patients were divided into two groups: 600 mg gabapentin and 1,200 mg gabapentin group. The quality of pain was assessed using VAS score. The results were statistically analyzed using Mann-Whitney Test with 95% confidence interval and considered significant if p value <0.05. From the results, the VAS values obtained at rest and during mobilization were significantly different (p<0.05. The 1,200 mg gabapentin group received less additional pethidine (10.5% vs 15.8%, although no significant difference was shown (p=0.631. The conclusion of this study is that administration of 1,200 mg gabapentin per oral pre operatively is better when compared to 600 mg in reducing post operative visual analog scale score in modified radical mastectomy. However, it do not reduce the need for analgesic significantly.

Synthesis and crystal structure of MgB12

International Nuclear Information System (INIS)

Adasch, Volker; Hess, Kai-Uwe; Ludwig, Thilo; Vojteer, Natascha; Hillebrecht, Harald

2006-01-01

Single crystals of MgB 12 were synthesized from the elements in a Mg/Cu melt at 1600deg. C. MgB 12 crystallizes orthorhombic in space group Pnma with a=16.632(3)A, b=17.803(4)A and c=10.396(2)A. The crystal structure (Z=30, 5796 reflections, 510 variables, R 1 (F)=0.049, wR 2 (I)=0.134) consists of a three dimensional net of B 12 icosahedra and B 21 units in a ratio 2:1. The B 21 units are observed for the first time in a solid compound. Mg is on positions with partial occupation. The summation reveals the composition MgB 12.35 or Mg 0.97 B 12 , respectively. This is in good agreement with the value of MgB 11.25 as expected by electronic reasons to stabilize the boron polyhedra B 12 2- and B 21 4-

Effect of combination tablets containing amlodipine 10 mg and irbesartan 100 mg on blood pressure and cardiovascular risk factors in patients with hypertension

Directory of Open Access Journals (Sweden)

Yagi S

2015-01-01

Full Text Available Shusuke Yagi,1 Akira Takashima,1 Minoru Mitsugi,2 Toshihiro Wada,2 Junko Hotchi,1 Ken-ichi Aihara,3 Tomoya Hara,1 Masayoshi Ishida,1 Daiju Fukuda,4 Takayuki Ise,1 Koji Yamaguchi,1 Takeshi Tobiume,1 Takashi Iwase,1 Hirotsugu Yamada,1 Takeshi Soeki,1 Tetsuzo Wakatsuki,1 Michio Shimabukuro,4 Masashi Akaike,5 Masataka Sata11Department of Cardiovascular Medicine, Graduate School of Health Biosciences, University of Tokushima, Tokushima, 2Department of Internal Medicine, Shikoku Central Hospital, Shikokuchuo, 3Department of Medicine and Bioregulatory Sciences, 4Department of Cardio-Diabetes Medicine, 5Department of Medical Education, Graduate School of Health Biosciences, University of Tokushima, Tokushima, JapanBackground: Hypertension is one of the major risk factors for cardiovascular and cerebrovascular disease and mortality. Patients who receive insufficient doses of antihypertensive agents or who are poorly adherent to multidrug treatment regimens often fail to achieve adequate blood pressure (BP control. The aim of this study was to determine the efficacy of an angiotensin II receptor blocker (ARB and calcium channel blocker (CCB combination tablet containing a regular dose of irbesartan (100 mg and a high dose of amlodipine (10 mg with regard to lowering BP and other risk factors for cardiovascular disease.Methods: We retrospectively evaluated data from 68 patients with essential hypertension whose treatment regimen was changed either from combination treatment with an independent ARB and a low-dose or regular-dose CCB or from a combination tablet of ARB and a low-dose or regular-dose CCB to a combination tablet containing amlodipine 10 mg and irbesartan 100 mg, because of incomplete BP control. Previous treatments did not include irbesartan as the ARB.Results: The combination tablet decreased systolic and diastolic BP. In addition, it significantly decreased serum uric acid, low-density lipoprotein cholesterol, and increased high

[Experimental research in vitro of TK/GCV system for osteosarcoma MG-63 cell damage].

Science.gov (United States)

Zhang, Hua-Dong; Lu, Zhi; Feng, Yi; Liu, Xiao-Li; Hou, Hui-Ming

2014-03-01

To study the killing effects of the liposome-mediated thymidine kinase (TK)/ganciclovir (GCV) system on MG-63 osteosarcoma (OS) cells and its bystander effects. Liposome-mediated TK gene transfected into MG-63 OS cells, the efficiency of transfection was analyzed by flow cytometry and observed under inverted fluorescence microscope. Non-transfected osteosarcoma MG-63 cells were divided into three groups,in the experimental group 1 transfected TK/GCV cells cultured in solutiona liquid mixture by supernatant by 1/10,1/7,1/5,1/2 ratio to original broth; in the experimental group 2 transfected cells cultured in solutiona liquid mixture of supernatant filtered through 0.22 microm filter by 1/10,1/7, 1/5, 1/2 ratio to original broth, in control group the transfection cells cultured in original culture solution. Cell growth inhibition rate and osteosarcoma cell sensitivity to TK/GCV system were measured by MTT assay in each group. The TK gene was transfected into MG-63 OS cells successfully by liposome-mediated, flow cytometry instrument detection TK gene transfection cell transfection efficiency can reach 75.5%. Six days later the MTT assay showed that in the experimental group 1 inhibition rate of all concentration ratio of the mixed culture fluid were statistically significant as compared with the control group (P culture medium was not statistically significant as compared with the control group (P > 0.05). TK gene transfected MG-63 cells increased with the the GCV concentration,the cell apoptosis rate increased. The experiment demonstrated that the MG-63 OS cells are sensitive to the liposome-mediated TK/GCV system and bystander effects are significant.

CHARACTERIZATION OF PHASES IN SECONDARY AlZn10Si8Mg CAST ALLOY

Directory of Open Access Journals (Sweden)

Eva Tillová

2011-04-01

Full Text Available Using recycled aluminium cast alloys is profitable in many aspects. Requiring only 5 % of the energy to produce secondary metal as compared to primary metal and generates only 5 % of the green house gas emissions, the recycling of aluminium is therefore beneficial of both environmental and economical point of view. Secondary AlZn10Si8Mg (UNIFONT® - 90 cast alloy are used for engine and vehicle constructions, hydraulic unit and mouldmaking without heat treatment. Properties include good castability, very good mechanical strength and elongation, light weight, good wear resistance, low thermal expansion and very good machining. Improved mechanical properties are strongly dependent upon the morphologies, type and distribution of the secondary phases, which are in turn a function of alloy composition and cooling rate. The presence of additional elements as Mg, Mn, Fe, or Cu allows many complex intermetallic phases to form, which make characterisation non-trivial. These include, for example, Mg2Si, Al2CuMg and AlFeMn phases, all of which may have some solubility for additional elements. Phase’s identification in aluminium alloys is often non-trivial due to the fact that some of the phases have either similar crystal structures or only subtle changes in their chemistries. A combination different analytical techniques (light microscopy upon black-white and colour etching, scanning electron microscopy (SEM upon deep etching, energy dispersive X-ray analysis (EDX and HV 0.01 microhardness measurement were therefore been used for the identification of the various phase.

Anestesia espinhal com 10 mg de bupivacaína hiperbárica associada a 5 µg de sufentanil para cesariana: estudo de diferentes volumes Anestesia espinal con 10 mg de bupivacaína hiperbárica asociada a 5 µg de sufentanil para cesárea: estudio de diferentes volúmenes Spinal Block with 10 mg of hyperbaric bupivacaine associated with 5 µg of sufentanil for cesarean section: study of different volumes

Directory of Open Access Journals (Sweden)

Angélica de Fátima de Assunção Braga

2010-04-01

the effectivity and side effects of different volumes of the subarachnoid administration of the association of hyperbaric bupivacaine and sufentanil in cesarean sections. METHODS: Forty patients, ASA I and II, undergoing elective cesarean section under spinal block were divided in two groups, according to the volume of the anesthetic solution: Group I (4 mL and Group II (3 mL. The association of hyperbaric bupivacaine (10 mg-2 mL and sufentanil (5 µg-1 mL was used in both groups. In Group I, 1 mL of NS was added to the solution to achieve the volume of 4 mL. The following parameters were evaluated: latency of the blockade; upper limit of the sensorial blockade; degree of motor blockade; time for regression of the motor blockade; total duration of analgesia; maternal side effects; and neonatal repercussions. RESULTS: Latency, the upper limit of the sensorial blockade, and the degree and time for regression of the motor blockade were similar in both groups; duration of analgesia was greater in Group I than in Group II, which was statistically significant. The incidence of side effects was similar in both groups. Maternal cardiocirculatory changes and neonatal repercussions were not observed. CONCLUSIONS: Four milliliter of anesthetic solution composed of hyperbaric bupivacaine, 10 mg, associated with 5 µg of sufentanil was more effective than 3 ml of the same solution, providing better intra-and postoperative analgesia without maternal-fetal repercussions.

CHARACTERIZATION OF PHASES IN SECONDARY AlZn10Si8Mg CAST ALLOY

OpenAIRE

Eva Tillová; Emília Ďuriníková; Mária Chalupová

2011-01-01

Using recycled aluminium cast alloys is profitable in many aspects. Requiring only 5 % of the energy to produce secondary metal as compared to primary metal and generates only 5 % of the green house gas emissions, the recycling of aluminium is therefore beneficial of both environmental and economical point of view. Secondary AlZn10Si8Mg (UNIFONT® - 90) cast alloy are used for engine and vehicle constructions, hydraulic unit and mouldmaking without heat treatment. Properties include good casta...

The dependence of Raman scattering on Mg concentration in Mg-doped GaN grown by MBE

International Nuclear Information System (INIS)

Flynn, Chris; Lee, William

2014-01-01

Magnesium-doped GaN (GaN:Mg) films having Mg concentrations in the range 5 × 10 18 –5 × 10 20 cm −3 were fabricated by molecular beam epitaxy. Raman spectroscopy was employed to study the effects of Mg incorporation on the positions of the E 2 and A 1 (LO) lines identifiable in the Raman spectra. For Mg concentrations in excess of 2 × 10 19 cm −3 , increases in the Mg concentration shift both lines to higher wave numbers. The shifts of the Raman lines reveal a trend towards compressive stress induced by incorporation of Mg into the GaN films. The observed correlation between the Mg concentration and the Raman line positions establish Raman spectroscopy as a useful tool for optimizing growth of Mg-doped GaN. (papers)

Comparison of the pharmacokinetics of a new 30 mg modified-release tablet formulation of metoclopramide for once-a-day administration versus 10 mg immediate-release tablets: a single and multiple-dose, randomized, open-label, parallel study in healthy male subjects.

Science.gov (United States)

Bernardo-Escudero, Roberto; Alonso-Campero, Rosalba; Francisco-Doce, María Teresa de Jesús; Cortés-Fuentes, Myriam; Villa-Vargas, Miriam; Angeles-Uribe, Juan

2012-12-01

The study aimed to assess the pharmacokinetics of a new, modified-release metoclopramide tablet, and compare it to an immediate-release tablet. A single and multiple-dose, randomized, open-label, parallel, pharmacokinetic study was conducted. Investigational products were administered to 26 healthy Hispanic Mexican male volunteers for two consecutive days: either one 30 mg modified-release tablet every 24 h, or one 10 mg immediate-release tablet every 8 h. Blood samples were collected after the first and last doses of metoclopramide. Plasma metoclopramide concentrations were determined by high-performance liquid chromatography. Safety and tolerability were assessed through vital signs measurements, clinical evaluations, and spontaneous reports from study subjects. All 26 subjects were included in the analyses [mean (SD) age: 27 (8) years, range 18-50; BMI: 23.65 (2.22) kg/m², range 18.01-27.47)]. Peak plasmatic concentrations were not statistically different with both formulations, but occurred significantly later (p 0.05)]. One adverse event was reported in the test group (diarrhea), and one in the reference group (headache). This study suggests that the 30 mg modified-release metoclopramide tablets show features compatible with slow-release formulations when compared to immediate-release tablets, and is suitable for once-a-day administration.

Effect of Ce-rich rare earth on microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy

Directory of Open Access Journals (Sweden)

You Zhiyong

2012-05-01

Full Text Available To improve the comprehensive mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy, different amount of Ce-rich rare earth (RE was added to the alloy, and the effect of RE addition on the microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb alloy was investigated by means of Brinell hardness measurement, scanning electron microscopy (SEM, energy dispersive spectroscope (EDS and X-ray diffraction (XRD. The results show that an appropriate amount of Ce-rich rare earth addition can make the Al4Ce phase particles and CeSb phase disperse more evenly in the alloy. These phases refine the alloy抯 matrix and make the secondary phases [t-Mg32(Al,Zn49 phase and f-Al2Mg5Zn2 phase] finer and more dispersive, therefore significantly improve the mechanical properties of the Mg-10Zn-5Al-0.1Sb alloy. When the RE addition is 1.0 wt.%, the tensile strengths of the alloy both at room temperature and 150 篊 reach the maximum values while the impact toughness is slightly lower than that of the matrix alloy. The hardness increases with the increase of RE addition.

Investigation of the 26Mg(d, p)27Mg reaction

NARCIS (Netherlands)

Meurders, F.; Steld, A. van der

1974-01-01

The angular distributions of 31 protons groups from the 26Mg(d, p)27Mg reaction have been measured at Ed = 12.0 MeV with a split-pole magnetic spectrograph. Excitation energies have been determined for 29 bound states. Three new levels have been found. A DWBA analysis yields ln values for 19 levels;

Design study of a 10 MW MgB2 superconductor direct drive wind turbine generator

DEFF Research Database (Denmark)

Abrahamsen, Asger Bech; Magnusson, Niklas; Liu, Dong

2014-01-01

A design study of a 10 MW direct drive wind turbine generator based on MgB2 superconducting wires is presented and the cost of the active materials of the generator is estimated to be between 226 €/kW and 84 €/kw, which is lower than the threshold values of 300 €/kW of the INNWIND.EU project. A n...

Synthesis and crystal structure of Mg{sub 0.5}NbO{sub 2}: An ion-exchange reaction with Mg{sup 2+} between trigonal [NbO{sub 2}]{sup -} layers

Energy Technology Data Exchange (ETDEWEB)

Miura, Akira, E-mail: amiura@yamanashi.ac.jp [Center for Crystal Science and Technology, University of Yamanashi (Japan); Takei, Takahiro; Kumada, Nobuhiro [Center for Crystal Science and Technology, University of Yamanashi (Japan)

2013-01-15

A new layered niobate, Mg{sub 0.5}NbO{sub 2}, was synthesized from LiNbO{sub 2} through a cation-exchange reaction with Mg{sup 2+} at 450-550 Degree-Sign C. This is the first example of a topotactic reaction with an aliovalent cation between trigonal [NbO{sub 2}]{sup -} layers. It is proposed to be isostructural with LiNbO{sub 2} (space group; P6{sub 3}/mmc) with lattice parameters of a=2.9052(6) A, c=10.625(15) A. The lattice parameters and formation energy of Mg{sub 0.5}NbO{sub 2} crystallized in LiNbO{sub 2} form and other layered CaNb{sub 2}O{sub 4} one were calculated by density functional theory. - Graphical abstract: A new layered niobate, Mg{sub 0.5}NbO{sub 2}, was synthesized from LiNbO{sub 2} through a cation-exchange reaction with Mg{sup 2+} at 450-550 Degree-Sign C. It is isostructural with LiNbO{sub 2} with lattice parameters of a=2.9052(6) A, c=10.625(15) A. Mg{sup 2+} are described in spheres located between [NbO{sub 2}]{sup -} trigonal layers and its occupancy is 0.5. Highlights: Black-Right-Pointing-Pointer A new layered niobate, Mg{sub 0.5}NbO{sub 2}, was synthesized from LiNbO{sub 2}. Black-Right-Pointing-Pointer Cation-exchange reaction converted two monovalent Li{sup +} into one divalent Mg{sup 2+} at 450-550 Degree-Sign C. Black-Right-Pointing-Pointer Mg{sub 0.5}NbO{sub 2} was isostructural with LiNbO{sub 2} (space group; P6{sub 3}/mmc). Black-Right-Pointing-Pointer Its lattice parameters were a=2.9052(6) A and c=10.625(15) A. Black-Right-Pointing-Pointer Synthesized Mg{sub 0.5}NbO{sub 2} was calculated to be thermodynamically more favorable.

Estimates of the astrophysical S-factors for proton radiative capture by 10B and 24Mg nuclei using the ANCs from proton transfer reactions

International Nuclear Information System (INIS)

Artemov, S.V.; Igamov, S.B.; Karakhodzhaev, A.A.; Nie, G.K.; Yarmukhamedov, R.; Zaparov, E.A.; Burtebaev, N.; Rehm, K.E.

2010-01-01

The contribution of the direct radiative capture of protons by 10 B and 24 Mg nuclei at low energies to the astrophysical S-factors in the reactions 10 B(p,γ) 11 C and 24 Mg(p,γ) 25 Al have been calculated within the R-matrix formalism by using empirical proton asymptotical normalization coefficients (ANC). The ANCs for bound proton configurations { 10 B+p} and { 24 Mg+p} were obtained from the analysis of the reactions ( 3 He, d). The ANCs were also estimated from the values of the neutron ANCs in the mirror nucleus 25 Mg following the suggestion that the neutron and the proton in the mirror states have equivalent nuclear potentials. It has been found that the S-factor for the reaction 10 B(p,γ) 11 C extrapolated to zero energy contributes ~100 keV b to the radiative capture to the ground state of 11 C. For the reaction 24 Mg(p,γ) 25 Al the value S(0) gives 58 keV b with a direct capture contribution of 41 keV b. (author)

Stability of Mg-sulfates at-10C and the rates of dehydration/rehydration processes under conditions relevant to Mars

Science.gov (United States)

Wang, A.; Freeman, J.J.; Chou, I.-Ming; Jolliff, B.L.

2011-01-01

We report the results of low temperature (-10??C) experiments on the stability fields and phase transition pathways of five hydrous Mg-sulfates. A low temperature form of MgSO 47H 2O (LT-7w) was found to have a wide stability field that extends to low relative humidity (???13% RH at-10??C). Using information on the timing of phase transitions, we extracted information on the reaction rates of five important dehydration and rehydration processes. We found that the temperature dependencies of rate constants for dehydration processes differ from those of rehydration, which reflect differences in reaction mechanisms. By extrapolating these rate constants versus T correlations into the T range relevant to Mars, we can evaluate the possibility of occurrence of specific processes and the presence of common Mg-sulfate species present on Mars in different periods and locations. We anticipate in a moderate obliquity period, starkeyite and LH-MgSO 4H 2O should be two common Mg-sulfates at the surface, another polymorph MH-MgSO 4H 2O can exist at the locations where hydrothermal processes may have occurred. In polar regions or within the subsurface of other regions, meridianiite (coexisting with water ice, near 100% RH) and LT-7w (over a large RH range) are the stable phases. During a high obliquity period, meridianiite and LT-7w should exhibit widespread occurrence. The correlations of reaction rates versus temperature found in this study imply that dehydration and rehydration of hydrous Mg-sulfates would always be slower than the sublimation and crystallization of water ice, which would be supported by mission observations from Odyssey and by Mars Exploration Rovers. Copyright 2011 by the American Geophysical Union.

Heterogeneous nucleation of Mg2Si on Sr11Sb10 nucleus in Mg–x(3.5, 5 wt.%)Si–1Al alloys

International Nuclear Information System (INIS)

Wang, Hui-Yuan; Chen, Lei; Liu, Bo; Li, Xiao-Ran; Wang, Jin-Guo; Jiang, Qi-Chuan

2012-01-01

After combined additions of Sr and Sb, most primary Mg 2 Si crystals in Mg–3.5Si–1Al and Mg–5Si–1Al alloys transformed from equiaxed-dendritic shapes to octahedral morphologies; while eutectic phases also changed from Chinese script to short rod-shapes. The mechanisms of complex modification of Sr and Sb were attributed to the heterogeneous nucleation of primary Mg 2 Si on Sr 11 Sb 10 nucleus, together with change in growth manners caused by incorporation of Sb in Mg 2 Si crystals. -- Highlights: ► The Sr 11 Sb 10 is the heterogeneous nucleation of primary Mg 2 Si in Mg–3.5Si–1Al alloys. ► Some Sb atoms were incorporated by substituting Si which changed growth manners of primary Mg 2 Si. ► Primary Mg 2 Si transformed from equiaxed-dendritic to octahedral after modification. ► Eutectic phases changed from Chinese script to short rod-shapes after modification.

On the fatigue behavior of friction stir welded AlSi 10 Mg alloy

Directory of Open Access Journals (Sweden)

Ramos, R. A.

2005-04-01

Full Text Available The high cycle fatigue behavior of friction stir welded AlSi10Mg samples was investigated for a stress ratio R = 0.1, ranging from 0.5 to 0.9 of the yield strength, in addition to tensile tests. The welds were produced with different tool rotation and travel speeds, and these welding parameters were correlated to residual stresses, measured by X-Ray diffraction (sen² ψmethod. Moreover, the residual stresses were measured during the fatigue testing, at fixed cycle intervals, being reported. It was observed that the residual (compressive stresses within the nugget were smaller than in the interface regions (between the thermomechanically affected zone and the base metal and stabilized above 4x10⁵ cycles. Fatigue crack morphology and microstructural changes were characterized by optical and electron microscopy and the observations are discussed along with the fatigue results.

Se estudia el comportamiento a la fatiga de alto ciclo de muestras de AlSi10Mg soldadas por fricción lineal para relación de tensión R = 0,1 cubriendo el rango de 0,5 a 0,9 de la resistencia a tracción, además de los datos del ensayo de tracción. Las soldaduras ensayadas fueron producidas con diferentes velocidades de rotación y avance de la herramienta. Las variables de proceso han sido correlacionadas con el análisis de tensiones residuales por difracción de Rayos X (método sen² ψ. Además, se midieron las tensiones residuales durante la deformación en fatiga a intervalos regulares de ciclos. Se observa que las tensiones residuales (de compresión dentro del nugget son más reducidas que en la interfase entre la región afectada térmica y mecánicamente y el material base, y se mantuvieron estables de manera progresiva a partir de los 4 x 10 ⁵ciclos. Se ha empleado la microscopía óptica y de barrido para evaluar la morfología y microestructura de las grietas de fatiga. Estos resultados se analizan

Lafutidine 10 mg versus Rabeprazole 20 mg in the Treatment of Patients with Heartburn-Dominant Uninvestigated Dyspepsia: A Randomized, Multicentric Trial

Directory of Open Access Journals (Sweden)

Bhupesh Dewan

2011-01-01

Full Text Available Background. Empirical therapy with antisecretory agents like PPIs and H2RAs has long been the traditional approach in the initial management of uninvestigated dyspepsia. Aim. The objective of the study was to examine relief of dyspepsia with lafutidine, a second-generation H2-RA, and rabeprazole and to compare their efficacy. Methods. This was a randomized, open, comparative trial in adult uninvestigated dyspeptic patients, who had at least moderate severity of symptoms, defined as a score of ≥4 on a 7-point global overall symptom (GOS scale, and were randomized to receive once daily either lafutidine 10 mg or rabeprazole 20 mg for 4 weeks. Results. A total of 236 patients were enrolled, out of which 194 patients were included in the analysis. At the end of week 4, a significant difference was observed for symptom relief (lafutidine 89.90% versus rabeprazole 65.26%, P<.01 and symptom resolution (lafutidine 70.71% versus rabeprazole 25.26%, P<.01. Both the drugs were well tolerated. Conclusion. Both lafutidine and rabeprazole provide symptom relief in patients with heartburn-dominant uninvestigated dyspepsia. The present study confirms the appropriateness of lafutidine as an empiric treatment and superior efficacy for primary care practice patients with dyspepsia.

On the fatigue behavior of friction stir welded AlSi 10 Mg alloy

International Nuclear Information System (INIS)

Alburquerque, J. M.; Ramos, P. A.; Gomes, M. A.; Cruz, A. C.

2005-01-01

The high cycle fatigue behaviour of friction stir welded AISi 10 Mg samples was investigated for a stress ratio R=0.1, ranging from 0.5 to 0.9 of the yield strength, in addition to tensile tests. The welds were produced with different tool rotation and travel speeds, and these welding parameters were correlated to residual stresses, measured by X-ray diffraction (sen''2Ψ method). Moreover, the residual stresses were measured during the fatigue testing, at fixed cycle intervals, being reported. It was observed that the residual (compressive)stresses within the nugget were smaller than in the interface regions (between the thermo-mechanically affected zone and the base metal) and stabilized above 4 x 10''5 cycles. Fatigue crack morphology and microstructural changes were characterized by optical and electron microscopy and the observations are discussed along with the fatigue results. (Author) 14 refs

Synthesis and crystal structure of Mg0.5NbO2: An ion-exchange reaction with Mg2+ between trigonal [NbO2]- layers

Science.gov (United States)

Miura, Akira; Takei, Takahiro; Kumada, Nobuhiro

2013-01-01

A new layered niobate, Mg0.5NbO2, was synthesized from LiNbO2 through a cation-exchange reaction with Mg2+ at 450-550 °C. This is the first example of a topotactic reaction with an aliovalent cation between trigonal [NbO2]- layers. It is proposed to be isostructural with LiNbO2 (space group; P63/mmc) with lattice parameters of a=2.9052(6) Å, c=10.625(15) Å. The lattice parameters and formation energy of Mg0.5NbO2 crystallized in LiNbO2 form and other layered CaNb2O4 one were calculated by density functional theory.

Live microbial cells adsorb Mg2+ more effectively than lifeless organic matter

Science.gov (United States)

Qiu, Xuan; Yao, Yanchen; Wang, Hongmei; Duan, Yong

2018-03-01

The Mg2+ content is essential in determining different Mg-CaCO3 minerals. It has been demonstrated that both microbes and the organic matter secreted by microbes are capable of allocating Mg2+ and Ca2+ during the formation of Mg-CaCO3, yet detailed scenarios remain unclear. To investigate the mechanism that microbes and microbial organic matter potentially use to mediate the allocation of Mg2+ and Ca2+ in inoculating systems, microbial mats and four marine bacterial strains ( Synechococcus elongatus, Staphylococcus sp., Bacillus sp., and Desulfovibrio vulgaris) were incubated in artificial seawater media with Mg/Ca ratios ranging from 0.5 to 10.0. At the end of the incubation, the morphology of the microbial mats and the elements adsorbed on them were analyzed using scanning electronic microscopy (SEM) and energy diffraction spectra (EDS), respectively. The content of Mg2+ and Ca2+ adsorbed by the extracellular polysaccharide substances (EPS) and cells of the bacterial strains were analyzed with atomic adsorption spectroscopy (AAS). The functional groups on the surface of the cells and EPS of S. elongatus were estimated using automatic potentiometric titration combined with a chemical equilibrium model. The results show that live microbial mats generally adsorb larger amounts of Mg2+ than Ca2+, while this rarely is the case for autoclaved microbial mats. A similar phenomenon was also observed for the bacterial strains. The living cells adsorb more Mg2+ than Ca2+, yet a reversed trend was observed for EPS. The functional group analysis indicates that the cell surface of S. elongatus contains more basic functional groups (87.24%), while the EPS has more acidic and neutral functional groups (83.08%). These features may be responsible for the different adsorption behavior of Mg2+ and Ca2+ by microbial cells and EPS. Our work confirms the differential Mg2+ and Ca2+ mediation by microbial cells and EPS, which may provide insight into the processes that microbes use to

The Influence of Selective Laser Melting Parameters on Density and Mechanical Properties of AlSi10Mg

Directory of Open Access Journals (Sweden)

Raus A. A.

2016-01-01

Full Text Available Selective Laser Melting (SLM is one of the most effective powder bed technique in the additive Manufacturing (AM which able to fabricate functional metal parts directly from 3D Computer Aided Design (CAD file data. In this paper, the influence of SLM parameters, such as laser power, scanning speed and hatching distance on the density of AlSi10Mg samples are investigated using one factor at a time (OFAT. Furthermore, the optimum results are used to fabricate samples for hardness, tensile strength, and impact toughness test. It is revealed that AlSi10Mg parts fabricated by SLM achieving the best density of 99.13% at the value of 350 watts laser power, 1650 mm/s scanning speed and hatching distance 0.13mm, whereby resulted comparable and even better mechanical properties to those of conventionally HDPC A360F and HDPC A360T6 alloys although without any comprehensive post processing methods.

Synthesis, crystal structure and optical properties of BiMgVO 5

Science.gov (United States)

Benmokhtar, S.; El Jazouli, A.; Chaminade, J. P.; Gravereau, P.; Guillen, F.; de Waal, D.

2004-11-01

The new vanadate BiMgVO 5 has been prepared and its structure has been determined by single crystal X-ray diffraction: space group P21/n, a=7.542(6) Å, b=11.615(5) Å, c=5.305(3) Å, β=107.38(5)°, wR2=0.0447, R=0.0255. The structure consists of [Mg 2O 10] and [Bi 2O 10] dimers sharing their corners with [VO 4] tetrahedra. The ranges of bond lengths are 2.129-2.814 Å for Bi-O; 2.035-2.167 Å for Mg-O and 1.684-1.745 Å for V-O. V-O bond lengths determined from Raman band wavenumbers are between 1.679 and 1.747 Å. An emission band overlapping the entire visible region with a maximum around 650 nm is observed.

Safety and pharmacokinetics of single and multiple intravenous bolus doses of diclofenac sodium compared with oral diclofenac potassium 50 mg: A randomized, parallel-group, single-center study in healthy subjects.

Science.gov (United States)

Munjal, Sagar; Gautam, Anirudh; Okumu, Franklin; McDowell, James; Allenby, Kent

2016-01-01

In a randomized, parallel-group, single-center study in 42 healthy adults, the safety and pharmacokinetic parameters of an intravenous formulation of 18.75 and 37.5 mg diclofenac sodium (DFP-08) following single- and multiple-dose bolus administration were compared with diclofenac potassium 50 mg oral tablets. Mean AUC0-inf values for a 50-mg oral tablet and an 18.75-mg intravenous formulation were similar (1308.9 [393.0]) vs 1232.4 [147.6]). As measured by the AUC, DFP-08 18.75 mg and 37.5 mg demonstrated dose proportionality for extent of exposure. One subject in each of the placebo and DFP-08 18.75-mg groups and 2 subjects in the DFP-08 37.5-mg group reported adverse events that were considered by the investigator to be related to the study drug. All were mild in intensity and did not require treatment. Two subjects in the placebo group and 1 subject in the DFP-08 18.75-mg group reported grade 1 thrombophlebitis; no subjects reported higher than grade 1 thrombophlebitis after receiving a single intravenous dose. The 18.75- and 37.5-mg doses of intravenous diclofenac (single and multiple) were well tolerated for 7 days. Additional efficacy and safety studies are required to fully characterize the product. © 2015, The American College of Clinical Pharmacology.

ZZ BOREHOLE-EB6.8-MG, multi group cross-section library for deterministic and Monte Carlo codes

International Nuclear Information System (INIS)

Kodeli, Ivo; Aldama, Daniel L.; Leege, Piet F.A. de; Legrady, David; Hoogenboom, J. Eduard

2007-01-01

1 - Description: Format: MATXS and ACE; Number of groups: 175 neutron, 45 gamma-ray; Nuclides: H-1, C-12, O-16, Na-23, Mg-nat, Al-27, Si-28, -29, -30, S-nat, Cl-35, -37, K-nat, Ca-nat, Mn-55, Fe-54, -56, -57, -58, I-127, W-nat. Origin: ENDF/B-VI.8; Weighting spectrum: Fission and fusion peak at high energies and a 1/E + thermal Maxwellian extension at low energies. The following materials/nuclides are included in the library: H-1, C-12, O-16, Na-23, Mg-nat, Al-27, Si-28, -29, -30, S-nat, Cl-35, -37, K-nat, Ca-nat, Fe-54, -56, -57, -58, Mn-55, I-127, W-nat. ZZ-BOREHOLE-EB6.8-MG is a multigroup cross section library for deterministic (DOORS, DANTSYS) and Monte Carlo (MCNP) transport codes developed for the oil well logging applications. The library is based on the ENDF/B-VI.8 evaluation and was processed by the NJOY-99 code. The cross sections are given in the 175 neutron and 45 gamma ray group structure. The MATXS format library can be directly used in TRANSX code to prepare the multigroup self-shielded cross sections for deterministic discrete ordinates codes like DOORS and DANTSYS. The data provided in the GROUPR and GAMINR format were converted to the MCNP ACE format by the NSLINK, SCALE and CRSRD codes. IAEA1398/03: Multigroup cross section data for Mn-55 were added in TRANSX format

Optimization of heat treatment parameters for additive manufacturing and gravity casting AlSi10Mg alloy

Science.gov (United States)

Girelli, L.; Tocci, M.; Montesano, L.; Gelfi, M.; Pola, A.

2017-11-01

Additive manufacturing of metals is a production process developed in the last few years to realize net shape components with complex geometry and high performance. AlSi10Mg is one of the most widely used aluminium alloys, both in this field and in conventional foundry processes, for its significant mechanical properties combined with good corrosion resistance. In this paper the effect of heat treatment on AlSi10Mg alloy was investigated. Solution and ageing treatments were carried out with different temperatures and times on samples obtained by direct metal laser sintering and gravity casting in order to compare their performance. Microstructural analyses and hardness tests were performed to investigate the effectiveness of the heat treatment. The results were correlated to the sample microstructure and porosity, analysed by means of optical microscopy and density measurements. It was found that, in the additive manufactured samples, the heat treatment can reduce significantly the performance of the alloy also because of the increase of porosity due to entrapped gas during the deposition technique and that the higher the solution temperature the higher the increase of such defects. A so remarkable effect was not found in the conventional cast alloy.

Effect of the addition of Al-Ti-C master alloy on the microstructure and microhardness of a cast Al-10Mg alloy

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The microstructure and microhardness of a cast Al-10wt%Mg (henceforth Al-l0Mg) alloy with 0.2wt% addition of Al-5Ti-0.25C master alloy were compared with those of a refiner-free alloy of similar chemical composition.It was found that this level of the master alloy addition not only caused an effective grain refinement, but also caused a significant increase in the microhardness of the Al-10Mg alloy.Microchemical analysis revealed that TiC particles existed in the grain center.The relationship between the holding time and grain size was also studied.It shows that the grain refining efficiency is faded observably with the holding time.This is explained in terms of the instability of TiC particles.

Validación de un método espectrofotométrico para la cuantificación de principio activo en tabletas de nifedipino 10 mg Validation of a spectrophotometric method for quantification of the active principle in 10 mg Nifedipine tablets

Directory of Open Access Journals (Sweden)

Yalexmi Ramos Rodríguez

2008-12-01

Full Text Available Se realizó la validación de una técnica espectrofotométrica para la cuantificación del principio activo en tabletas de nifedipino 10 mg con el empleo de etanol al 96 % como solvente. Se determinaron los parámetros de linealidad, exactitud, precisión intermedia, repetibilidad, especificidad y robustez. Se comprobó que el método es lineal, exacto y preciso en un rango de 85 a 115 %, lo que demuestra la fiabilidad del método y su posibilidad de empleo en el control de la calidad de la forma terminada.The validation of a spectrophotometric method for the determination of active principle in tablets of nifedipine 10 mg is presented in this work. The linearity, precision, exactitude, specificity and robustness of the method were evaluated. The method employed was linear, exact and precise in the interval of 85 % to 115%. This proves that the method can be used in the tablets' quality control.

Exigências nutricionais em macronutrientes minerais (Ca, P, Mg, Na e K para novilhos de diferentes grupos genéticos Macrominerals (Ca, P, Mg, Na, and K requirements for young bulls from different genetic groups

Directory of Open Access Journals (Sweden)

Fernando de Paula Leonel

2006-04-01

Full Text Available Determinaram-se as exigências em macronutrientes minerais (Ca, P, Mg, Na e K utilizando-se 44 novilhos não-castrados, pertencentes a quatro grupos genéticos (Nelore; F1 Nelore x Aberdeen-Angus; F1 Nelore x Pardo-Suíço e F1 Nelore x Simental, com média de 10 e 11 meses de idade e peso vivo inicial de 362 ± 35 kg. A ração experimental foi composta de feno de capim-braquiária (Brachiaria decumbens, Stapf., farelo de soja, milho (grão moído, melaço em pó e suplementos de macro e micronutrientes inorgânicos. As exigências líquidas para ganho de peso, em cada macronutriente, foram obtidas por meio da derivada primeira de suas respectivas equações, estimadas a partir de regressão não-linear do conteúdo do nutriente (Ca, P, Mg, Na e K, em função do peso de corpo vazio do animal. Para conversão do peso vivo em peso de corpo vazio, utilizou-se a equação obtida a partir da regressão do peso corporal vazio dos animais experimentais em função de seus pesos imediatamente antes do abate. As exigências de mantença foram estimadas de acordo com as recomendações do NRC e ARC e os coeficientes de absorção adotados para os cinco macronutrientes foram aqueles propostos pelo ARC. O teste de identidade de modelos indicou não haver diferenças entre as equações de regressão para os minerais entre os quatro grupos genéticos estudados. Não foram verificadas, pela análise de variância, diferenças entre as exigências de macrominerais entre os diferentes grupos genéticos.The objective of this trial was to determine the macrominerals requirements (Ca, P, Mg, Na, and K for young bulls from different genetic groups. Forty-four young bulls from the following genetic groups were used: Nellore, F1 Nellore x Aberdeen-Angus, F1 Nellore x Brown Swiss, and F1 Nellore x Simmental. Animals averaged 362 ± 35 kg of initial body weight and between 10 to 11 months of age. Diet contained signal grass hay (Brachiaria decumbens, Stapf., soybean

Adsorption of arginine, glycine and aspartic acid on Mg and Mg-based alloy surfaces: A first-principles study

Science.gov (United States)

Fang, Zhe; Wang, Jianfeng; Yang, Xiaofan; Sun, Qiang; Jia, Yu; Liu, Hairong; Xi, Tingfei; Guan, Shaokang

2017-07-01

Studying the adsorption behaviors of biomolecules on the surface of Mg and Mg-based alloy has a fundamental and important role for related applications in biotechnology. In the present work, we systematically investigate and compare the adsorption properties of three typical amino acids, i.e., Arg (arginine), Gly (glycine) and Asp (aspartic acid), which form RGD tripeptide, on the Mg (0 0 0 1) surface with various doping (Zn, Y, and Nd), and aim to realize proper binding between biomolecules and Mg and Mg-based biomedical materials. Our results show that flat adsorption configurations of the functional groups binding to the surfaces are favored in energy for all the three selected amino acids. In specific, for the amino acids adsorped on clean Mg (0 0 0 1) surface, the adsorption energy (Eads) of Arg is found to be -1.67 eV for the most stable configuration, with amino and guanidyl groups binding with the surface. However, Gly (Asp) is found to binding with the surface through amino and carboxyl groups, with a -1.16 eV (-1.15 eV) binding energy. On the 2% Zn doped Mg (0 0 0 1) alloy surface (Mg-Zn (2%)), the Eads are significantly increased to be -1.91 eV, -1.32 eV and -1.35 eV for Arg, Gly and Asp, respectively. While the Mg-Y (1%) and Mg-Nd (1%) slightly weaken the adsorption of three amino acids. Moreover, we have performed detail discussions of the binding properties between amino acids and surfaces by projected density of states (PDOS) combined with charge transfer analyses. Our studies provide a comprehensive understanding on the interactions between amino acids and Mg and Mg-based alloy surfaces, with respect to facilitate the applications of Mg and Mg-based biomedical alloys in biosensing, drug delivery, biomolecule coating and other fields in biotechnology.

Geometric Effects of La1+xMg2-xNi9 (x=0.0～1.0) Ternary Alloys on Their Hydrogen Storage Capacities

Institute of Scientific and Technical Information of China (English)

Zhiqing YUAN; Guanglie LU; Bin LIAO; Yongquan LEI

2005-01-01

Structural analysis was made using X-ray diffraction (XRD) Rietveld refinement on a series of La1+xMg2-xNi9(x=0.0～1.0) ternary alloys. Results showed that each of La1+xMg2-xNi9 alloys was a PuNi3-type structure stacked by LaNi5 and (La, Mg) Ni2 blocks. Electrochemical tests revealed that discharge abilities of these La-Mg-Ni ternary alloys mainly depended on their atomic distances between (La, Mg) and Ni, which could be modified by varying the atomic ratios of La/Mg.

A Negative Thermal Expansion Material of ZrMgMo3O12

International Nuclear Information System (INIS)

Song Wen-Bo; Liang Er-Jun; Liu Xian-Sheng; Li Zhi-Yuan; Yuan Bao-He; Wang Jun-Qiao

2013-01-01

A material with the formula ZrMgMo 3 O 12 having negative thermal expansion is presented and characterized. It is shown that ZrMgMo 3 O 12 crystallizes in an orthorhombic symmetry with space group Pnma(62) or Pna2 1 (33) and exhibits negative thermal expansion in a large temperature range (α l = −3.8 × 10 −6 K −1 from 300K to 1000K by x-ray diffraction and α l = −3.73 × 10 −6 K −1 from 295K to 775K by dilatometer). ZrMgMo 3 O 12 remains the orthorhombic structure without phase transition or decomposition at least from 123K to 1200K and is not hygroscopic. These properties make it an excellent material with negative thermal expansion for a variety of applications

Preparation of c-axis perpendicularly oriented ultra-thin L10-FePt films on MgO and VN underlayers

Science.gov (United States)

Futamoto, Masaaki; Shimizu, Tomoki; Ohtake, Mitsuru

2018-05-01

Ultra-thin L10-FePt films of 2 nm average thickness are prepared on (001) oriented MgO and VN underlayers epitaxially grown on base substrate of SrTiO3(001) single crystal. Detailed cross-sectional structures are observed by high-resolution transmission electron microscopy. Continuous L10-FePt(001) thin films with very flat surface are prepared on VN(001) underlayer whereas the films prepared on MgO(001) underlayer consist of isolated L10-FePt(001) crystal islands. Presence of misfit dislocation and lattice bending in L10-FePt material is reducing the effective lattice mismatch with respect to the underlayer to be less than 0.5 %. Formation of very flat and continuous FePt layer on VN underlayer is due to the large surface energy of VN material where de-wetting of FePt material at high temperature annealing process is suppressed under a force balance between the surface and interface energies of FePt and VN materials. An employment of underlayer or substrate material with the lattice constant and the surface energy larger than those of L10-FePt is important for the preparation of very thin FePt epitaxial thin continuous film with the c-axis controlled to be perpendicular to the substrate surface.

Surface structure of MgO underlayer with Ti diffusion for (002 oriented L10 FePt-based heat assisted magnetic recording media

Directory of Open Access Journals (Sweden)

Sintaro Hinata

2018-05-01

Full Text Available Surface morphology of the MgO layer and magnetic properties of FePt-C layer deposited on the MgO were investigated for the FePt-based heat assisted magnetic recording media. Stacking structure of the underlayer for the FePt-C layer was MgO (0-5 nm/Cr80Mn20 (0-30 nm/Cr50Ti50 (0-50 nm/glass sub.. Surface observation result for the MgO film by using an atomic force microscope revealed the existence of nodules with a height of about 2 nm and a network-like convex structure with a height difference of about sub nm (boundary wall, BW on the MgO crystal grain boundary. Density of the nodules largely depends on the surface roughness of the CrTi layer, RaCrTi and it is suppressed from 10 to 2/0.5 μm2 by reducing RaCrTi from 420 to 260 pm. Height of the BW depends on thickness of the MgO layer, tMgO and it can be suppressed by reducing tMgO to less than 4 nm. From the cross-sectional energy dispersive x-ray mapping, it is clarified that the BW is formed by atomic diffusion of Ti atoms from CrTi layer due to the substrate heating process, and a compound consists of Mg, Ti and O atoms. This BW can be used as a template to magnetically isolate the FePt column in the FePt-based granular film, such as FePt-SiO2, if the size of the BW is reduced to less than 10 nm. M-H loop of the FePt-C granular film deposited on the underlayer showed that the nodule and BW induce oxidation of the FePt grains, and reduction of intergranular exchange coupling.

Surface structure of MgO underlayer with Ti diffusion for (002) oriented L10 FePt-based heat assisted magnetic recording media

Science.gov (United States)

Hinata, Sintaro; Jo, Shin; Saito, Shin

2018-05-01

Surface morphology of the MgO layer and magnetic properties of FePt-C layer deposited on the MgO were investigated for the FePt-based heat assisted magnetic recording media. Stacking structure of the underlayer for the FePt-C layer was MgO (0-5 nm)/Cr80Mn20 (0-30 nm)/Cr50Ti50 (0-50 nm)/glass sub.. Surface observation result for the MgO film by using an atomic force microscope revealed the existence of nodules with a height of about 2 nm and a network-like convex structure with a height difference of about sub nm (boundary wall, BW) on the MgO crystal grain boundary. Density of the nodules largely depends on the surface roughness of the CrTi layer, RaCrTi and it is suppressed from 10 to 2/0.5 μm2 by reducing RaCrTi from 420 to 260 pm. Height of the BW depends on thickness of the MgO layer, tMgO and it can be suppressed by reducing tMgO to less than 4 nm. From the cross-sectional energy dispersive x-ray mapping, it is clarified that the BW is formed by atomic diffusion of Ti atoms from CrTi layer due to the substrate heating process, and a compound consists of Mg, Ti and O atoms. This BW can be used as a template to magnetically isolate the FePt column in the FePt-based granular film, such as FePt-SiO2, if the size of the BW is reduced to less than 10 nm. M-H loop of the FePt-C granular film deposited on the underlayer showed that the nodule and BW induce oxidation of the FePt grains, and reduction of intergranular exchange coupling.

Comparative study of 250 mg/day terbinafine and 100 mg/day itraconazole for the treatment of cutaneous sporotrichosis.

Science.gov (United States)

Francesconi, Glaucia; Francesconi do Valle, Antonio Carlos; Passos, Sonia Lambert; de Lima Barros, Mônica Bastos; de Almeida Paes, Rodrigo; Curi, André Luiz Land; Liporage, José; Porto, Cássio Ferreira; Galhardo, Maria Clara Gutierrez

2011-05-01

Itraconazole is currently used for the treatment of cutaneous sporotrichosis. Terbinafine at a daily dose of 250 mg has been successfully applied to the treatment of cutaneous sporotrichosis. To compare the efficacy of 250 mg/day terbinafine and 100 mg/day itraconazole for the treatment of cutaneous sporotrichosis. A bidirectional cohort study was conducted on 55 patients receiving 250 mg/day terbinafine and 249 patients receiving 100 mg/day itraconazole. The latter patients were matched for age and clinical form to the terbinafine group at a ratio of 5:1. Sporothrix schenckii was isolated by culture from all patients (age range: 18-70 years), who were submitted to the standard care protocol consisting of clinical and laboratory evaluation and periodic visits. Cure was observed in 51 (92.7%) patients of the terbinafine group and 229 (92%) of the itraconazole group within a similar mean period of time (11.5 and 11.8 weeks, respectively). An increase in the terbinafine dose to 500 mg was necessary in two patients due to the lack of a response, and one patient presented recurrence. In the itraconazole group, two patients required a dose increase and three presented recurrence. Adverse events were equally frequent among patients receiving terbinafine (n = 4, 7.3%) and itraconazole (n = 19, 7.6%) and were generally mild without the need for drug discontinuation, except for two patients of the itraconazole group. Terbinafine administered at a daily dose of 250 mg is an effective and well-tolerated option for the treatment of cutaneous sporotrichosis.

Atomic structure of glassy Mg60Cu30Y10 investigated with EXAFS, x-ray and neutron diffraction, and reverse Monte Carlo simulations

DEFF Research Database (Denmark)

Jovari, P.; Saksl, K.; Pryds, Nini

2007-01-01

Short range order of amorphous Mg60Cu30Y10 was investigated by x-ray and neutron diffraction, Cu and Y K-edge x-ray absorption fine structure measurements, and the reverse Monte Carlo simulation technique. We found that Mg-Mg and Mg-Cu nearest neighbor distances are very similar to values found...... in crystalline Mg2Cu. The Cu-Y coordination number is 1.1 +/- 0.2, and the Cu-Y distance is similar to 4% shorter than the sum of atomic radii, suggesting that attraction between Cu and Y plays an important role in stabilizing the glassy state. Thermal stability and structure evolution upon annealing were also...

Clinical efficacy and safety of a new 1000-mg suspension versus twice-daily 500-mg tablets of MPFF in patients with symptomatic chronic venous disorders: a randomized controlled trial.

Science.gov (United States)

Carpentier, Patrick; van Bellen, Bonno; Karetova, Debora; Hanafiah, Harunarashid; Enriquez-Vega, Elizabeth; Kirienko, Alexander; Dzupina, Andrej; Sabovic, Miso; Reina Gutierrez, Lourdes; Subwongcharoen, Somboom; Tüzün, Hasan; Maggioli, Arnaud

2017-10-01

Chronic venous disorders (CVD) is estimated to affect 30% to 50% of women and 10% to 30% of men. The most widely prescribed treatment for CVD worldwide is micronized purified flavonoid fraction 500 mg (MPFF). The aim of this clinical trial was to develop a new once daily 1000-mg oral suspension of MPFF. In an international, randomized, double-blind, parallel-group study, symptomatic individuals classified CEAP C0s to C4s were randomized in either treatment arm and treated for 8 weeks. Lower limb symptoms (discomfort, pain and heaviness) were assessed using Visual Analog Scales (VAS), and quality of life (QoL) was measured with the CIVIQ-20 Questionnaire. A total of 1139 patients were included in the study. Both MPFF treatment regimens were well tolerated and associated with a significant reduction in lower limb symptoms. A non-inferiority of MPFF 1000-mg oral suspension once daily compared to MPFF 500-mg tablet twice daily (P1000 mg and -3.37 cm for MPFF 500 mg), leg pain (-3.27 cm for MPFF 1000 mg and -3.31 cm for MPFF 500 mg) and leg heaviness (-3.41 cm for MPFF 1000 mg and -3.46 cm for MPFF 500 mg). The patients' QoL was improved by about 20 points on the CIVIQ scale in both groups (19.33 points for MPFF 1000 mg and 20.28 points for MPFF 500 mg). MPFF 1000-mg oral suspension and MPFF 500-mg tablets treatments were associated with similar reductions in lower limb symptoms and QoL improvement. The new once daily MPFF1000-mg oral suspension has a similar safety profile to two tablets of MPFF 500 mg, with the advantage of one daily intake, potentially associated with improved patient adherence and easier CVD management.

The AlSi10Mg samples produced by selective laser melting: single track, densification, microstructure and mechanical behavior

International Nuclear Information System (INIS)

Wei, Pei; Wei, Zhengying; Chen, Zhen; Du, Jun; He, Yuyang; Li, Junfeng; Zhou, Yatong

2017-01-01

Highlights: • The thermal behavior of AlSi10Mg molten pool was analyzed. • The SLM-processed sample with a relatively low surface roughness was obtained. • Effects of parameters on surface topography of scan track were investigated. • Effects of parameters on microstructure of parts were investigated. • Optimum processing parameters for AlSi10Mg SLM was obtained. - Abstract: This densification behavior and attendant microstructural characteristics of the selective laser melting (SLM) processed AlSi10Mg alloy affected by the processing parameters were systematically investigated. The samples with a single track were produced by SLM to study the influences of laser power and scanning speed on the surface morphologies of scan tracks. Additionally, the bulk samples were produced to investigate the influence of the laser power, scanning speed, and hatch spacing on the densification level and the resultant microstructure. The experimental results showed that the level of porosity of the SLM-processed samples was significantly governed by energy density of laser beam and the hatch spacing. The tensile properties of SLM-processed samples and the attendant fracture surface can be enhanced by decreasing the level of porosity. The microstructure of SLM-processed samples consists of supersaturated Al-rich cellular structure along with eutectic Al/Si situated at the cellular boundaries. The Si content in the cellular boundaries increases with increasing the laser power and decreasing the scanning speed. The hardness of SLM-processed samples was significantly improved by this fine microstructure compared with the cast samples. Moreover, the hardness of SLM-processed samples at overlaps was lower than the hardness observed at track cores.

The AlSi10Mg samples produced by selective laser melting: single track, densification, microstructure and mechanical behavior

Energy Technology Data Exchange (ETDEWEB)

Wei, Pei; Wei, Zhengying, E-mail: zywei@mail.xjtu.edu.cn; Chen, Zhen; Du, Jun; He, Yuyang; Li, Junfeng; Zhou, Yatong

2017-06-30

Highlights: • The thermal behavior of AlSi10Mg molten pool was analyzed. • The SLM-processed sample with a relatively low surface roughness was obtained. • Effects of parameters on surface topography of scan track were investigated. • Effects of parameters on microstructure of parts were investigated. • Optimum processing parameters for AlSi10Mg SLM was obtained. - Abstract: This densification behavior and attendant microstructural characteristics of the selective laser melting (SLM) processed AlSi10Mg alloy affected by the processing parameters were systematically investigated. The samples with a single track were produced by SLM to study the influences of laser power and scanning speed on the surface morphologies of scan tracks. Additionally, the bulk samples were produced to investigate the influence of the laser power, scanning speed, and hatch spacing on the densification level and the resultant microstructure. The experimental results showed that the level of porosity of the SLM-processed samples was significantly governed by energy density of laser beam and the hatch spacing. The tensile properties of SLM-processed samples and the attendant fracture surface can be enhanced by decreasing the level of porosity. The microstructure of SLM-processed samples consists of supersaturated Al-rich cellular structure along with eutectic Al/Si situated at the cellular boundaries. The Si content in the cellular boundaries increases with increasing the laser power and decreasing the scanning speed. The hardness of SLM-processed samples was significantly improved by this fine microstructure compared with the cast samples. Moreover, the hardness of SLM-processed samples at overlaps was lower than the hardness observed at track cores.

[Effect of M007 mediated photodynamic therapy on proliferation of human osteosarcoma MG63 cells in vitro].

Science.gov (United States)

Zhou, Yu-Kai; Wu, Wen-Zhi; Zhang, Lan; Yang, Chun-Hui; Wang, Yan-Ping

2012-01-01

To investigate the effect of a new photosensitizer, M007 mediated photodynamic therapy on proliferation of human osteosarcoma MG63 cells in vitro. Human osteosarcoma MG63 cells were prepared as 1 x 10(6) /mL single-cell suspension, and 1 mL cells were transferred into 60 mL culture dish, then treated with 5 different gradient dosages (0, 2, 4, 8, 16 micromol/L) of M007 followed by photodynamic therapy or dark reaction for 10 min. The survival rate of the cells and the mode of cell death were detected by flow cytometry with the stain of Annexin V-FITC/PI. The effect on proliferation of survival cells was observed by MTT assay and colony-forming assay. M007 mediated photodynamic therapy induced the inactivation of MG63 human osteosarcoma cells in the way of late apoptosis/necrosis or becoming naked nucleus predominately. More than 90% MG63 cells in M007-PDT group were dead under the treatment of 2-16 micromol/L M007. The survival rates of 4-16 micromol/L M007-PDT group were steadily less than 1%. The optical densities did not increase with extension of culture time in 2-8 micromol/L M007-PDT group (P > 0.05). There were 16 survival alive cells found occasionally in 2 micromol/L M007-PDT group, but no colonies found in other groups. M007 mediated photodynamic therapy totally inactivated human osteosarcoma MG63 cells in vitro with the dosage more than 4 micromol/L.

Formation process of micro arc oxidation coatings obtained in a sodium phytate containing solution with and without CaCO{sub 3} on binary Mg-1.0Ca alloy

Energy Technology Data Exchange (ETDEWEB)

Zhang, R.F. [School of Material and Electromechanics, Jiangxi Science and Technology Normal University, Nanchang 330013 (China); Zhang, Y.Q. [Zhejiang DunAn Light Alloy Technology CO,.LTD, Zhuji 311835 (China); Hunan University of Science and Technology, Xiangtan 411201 (China); Zhang, S.F.; Qu, B. [School of Material and Electromechanics, Jiangxi Science and Technology Normal University, Nanchang 330013 (China); Guo, S.B. [Hunan University of Science and Technology, Xiangtan 411201 (China); Xiang, J.H., E-mail: xiangjunhuai@163.com [School of Material and Electromechanics, Jiangxi Science and Technology Normal University, Nanchang 330013 (China)

2015-01-15

Highlights: • Compared to the Mg phase, the area of Mg{sub 2}Ca phase is much smaller. • The coatings are preferentially developed on the area adjacent to Mg{sub 2}Ca phase. • During MAO process, some sodium phytate molecules are hydrolyzed. • Anodic coatings are developed from uneven to uniform. - Abstract: Micro arc oxidation (MAO) is an effective method to improve the corrosion resistance of magnesium alloys. In order to reveal the influence of alloying element Ca and CaCO{sub 3} electrolyte on the formation process and chemical compositions of MAO coatings on binary Mg-1.0Ca alloy, anodic coatings after different anodizing times were prepared on binary Mg-1.0Ca alloy in a base solution containing 3 g/L sodium hydroxide and 15 g/L sodium phytate with and without addition of CaCO{sub 3}. The coating formation was studied by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The results show that Mg-1.0Ca alloy is composed of two phases, the Mg phase and Mg{sub 2}Ca phase. After treating for 5 s, the coating began to develop and was preferentially formed on the area nearby Mg{sub 2}Ca phase, which may be resulted from the intrinsic electronegative potential of the Mg phase than that of Mg{sub 2}Ca phase. Anodic coatings unevenly covered the total surface after 20 s. After 80 s, the coatings were uniformly developed on Mg-1.0Ca alloy with micro pores. During MAO process, some sodium phytate molecules are hydrolyzed into inorganic phosphate. CaCO{sub 3} has minor influence on the calcium content of the obtained MAO coatings.

Interaction of the D-isomer of 4-methylene glutamate (4-MG) with an active site thiol group of γ-glutamylcysteine synthetase (γ-GCS)

International Nuclear Information System (INIS)

Simondsen, R.P.; Meister, A.

1986-01-01

γ-GCS has an SH-group at or close to the glutamate binding site. During efforts to find a covalently bound inhibitor, the authors examined interaction of the enzyme with 4-MG with the thought that a glutamate analog with an α,β-unsaturated moiety might bind to the glutamate site and react with the active site thiol. 4-MG is not a significant substrate, but inhibits in the usual assay. Preincubation of the enzyme with DL-4-MG inactivated markedly and to about the same extent as found after preincubation with half the concentration of D-4-MG (prepared by action of glutamate decarboxylase on DL-4-MG); L-4-MG did not inactivate. Inactivation by 4-MG was decreased in the presence of L-glutamate. Inactivation by 4-MG was prevented by prior treatment of the enzyme with cystamine, which forms a disulfide with the active site thiol. After inactivation of the enzyme with 4-[2- 14 C]MG followed by separation of the enzyme by gel filtration, 0.9 mole of label was found per mole of enzyme, amino acid analysis after acid hydrolysis of the labeled enzyme gave labeled products that include the expected adduct formed by reaction of cysteine with 4-MG

Experimental investigation on densification behavior and surface roughness of AlSi10Mg powders produced by selective laser melting

Science.gov (United States)

Wang, Lin-zhi; Wang, Sen; Wu, Jiao-jiao

2017-11-01

Effects of laser energy density (LED) on densities and surface roughness of AlSi10Mg samples processed by selective laser melting were studied. The densification behaviors of the SLM manufactured AlSi10Mg samples at different LEDs were characterized by a solid densitometer, an industrial X-ray and CT detection system. A field emission scanning electron microscope, an automatic optical measuring system, and a surface profiler were used for measurements of surface roughness. The results show that relatively high density can be obtained with the point distance of 80-105 μm and the exposure time of 140-160 μs. The LED has an important influence on the surface morphology of the forming part, too high LED may lead to balling effect, while too low LED tends to produce defects, such as porosity and microcrack, and then affect surface roughness and porosities of the parts finally.

Comparison of the Effect of 800 mg Ibuprofen and 30 mg Predenisolone on Relief of Post Endodontic Pain

Directory of Open Access Journals (Sweden)

S.M. Jalalzadeh

2009-04-01

Full Text Available Introduction & Objective: One of the important problems in dentistry is post endodontic pains .The purpose of this study was comparison of the effect of prophylactic oral ibuprofen 800mg and oral predenisolone 30mg on prevention of post endodontic pain.Materials & Methods: The present study is a double-blind, randomized and controlled trial. It was conducted on 60 patient (16men and 44 women between the ages of 18-63 who needed endodontic treatment. Inclusive criteria for selecting of patients were: need for root canal therapy in one of the posterior teeth, having no systemic problem, no evidence of abscess; not taking analgesic or similar drug for at least 6 hours before treatment. Patients were divided into three experimental groups randomly taking one of the drugs before the treatment {ibuprofen 800 mg, prednisolone30mg and placebo (oral dextrose}. Patients completed VAS at 6,12 and 24 hours post root canal therapy and analyzed using the spss15 by chi-square, ANOVA test and Tukey test.Results: During 24 hours after treatment post endodontic pain is 95%- 100% in the placebo group. The prevalence of no-pain was not significant 6, 12 and 24 hours after treatment between the ibuprofen and predenisolone groups. The mean scale of pain in ibuprofen and predenisolone groups was significantly lower than placebo group 6, 12 and 24 hours after treatment. Differences between the drug groups are significant only on 6 and 12 hours after treatment.Conclusion: Post endodontic pains are present 24 hours after treatment. 6 and 12 hours after treatment 30 mg predenisolone are significantly better for pain relief than 800 mg ibuprofen. But after 24 hours it is not significant.

Transport properties and exponential n-values of Fe/MgB2 tapes with various MgB2 particle sizes

International Nuclear Information System (INIS)

Lezza, P.; Abaecherli, V.; Clayton, N.; Senatore, C.; Uglietti, D.; Suo, H.L.; Fluekiger, R.

2004-01-01

Fe/MgB 2 tapes have been prepared starting with pre-reacted binary MgB 2 powders. As shown by resistive and inductive measurements, the reduction of particle size to a few microns by ball milling has little influence on B c2 , while the superconducting properties of the individual MgB 2 grains are essentially unchanged. Reducing the particle size causes an enhancement of B irr from 14 to 16 T, while J c has considerably increased at high fields, its slope J c (B) being reduced. At 4.2 K, values of 5.3 x 10 4 and 1.2 x 10 3 A/cm 2 were measured at 3.5 and 10 T, respectively, suggesting a dominant role of the conditions at the grain interfaces. A systematic variation of these conditions at the interfaces is undertaken in order to determine the limit of transport properties for Fe/MgB 2 tapes. The addition of 5% Mg to MgB 2 powder was found to affect neither J c nor B c2 . For the tapes with the highest J c values, very high exponential n factors were measured: n=148, 89 and 17 at 3.5, 5 and 10 T, respectively and measurements of critical current versus applied strain have been performed. The mechanism leading to high transport critical current densities of filamentary Fe/MgB 2 tapes based on MgB 2 particles is discussed

Structural Phase Transitions of Mg(BH4)2 under Pressure

International Nuclear Information System (INIS)

George, L.; Drozd, V.; Saxena, S.; Bardaji, E.; Fichtner, M.

2009-01-01

The structural stability of Mg(BH4)2, a promising hydrogen storage material, under pressure has been investigated in a diamond anvil cell up to 22 GPa with combined synchrotron X-ray diffraction and Raman spectroscopy. The analyses show a structural phase transition around 2.5 GPa and again around 14.4 GPa. An ambient-pressure phase of Mg(BH4)2 has a hexagonal structure (space group P61, a = 10.047(3) A, c = 36.34(1) A, and V = 3176(1) A3 at 0.2 GPa), which agrees well with early reports. The structure of high-pressure phase is found to be different from reported theoretical predictions; it also does not match the high-temperature phase. The high-pressure polymorph of Mg(BH4)2 is found to be stable on decompression, similar to the case of the high-temperature phase. Raman spectroscopic study shows a similarity in high-pressure behavior of as-prepared Mg(BH4)2 and its high-temperature phase.

Isotope ratio 87Sr/86Sr in limestones from Bambui group, Brazil (MG)

International Nuclear Information System (INIS)

Kawashita, K.; Mizusaki, A.M.P.; Kiang, C.H.

1987-01-01

The Sr composition of ancient seawater can be estimated from the analysis of carbonate rocks and, in some cases, used to estimate the age of the analyzed carbonate. The normalized 87Sr/86Sr ratios in calcium carbonate fractions from 14 core samples in the Bambui Group near Montalvania, MG, were found to range between .7077 and .7280. The higher values are attributable to Sr isotopic exchange between silicate and carbonate phases during diagenesis. The ratio of .7077 obtained in two pure calcium carbonate samples is here suggested as the best aproximation for the 87Sr/86Sr value for the Bambui sea. This ratio is compatible with an age of about 700 Ma., estimated from the published 87Sr/86Sr curve of Veizer and others, an age in accordance with Quadros recent (1987, in preparation) identification of marine acritarchs from the latest Precambrian (Vendian). (author) [pt

Hydrogenation Properties of Mg-5 wt.% TiCr_10NbX (x=1,3,5) Composites by Mechanical Alloying Process

International Nuclear Information System (INIS)

Kim, Kyeong-Il; Hong, Tae-Whan

2011-01-01

Hydrogen and hydrogen energy have been recognized as clean energy sources and high energy carrier. Mg and Mg alloys are attractive hydrogen storage materials because of their lightweight and low cost materials with high hydrogen capacity (about 7.6 wt.%). However, the commercial applications of the Mg hydrides are currently hinder by its high absorption/desorption temperature, and very slow reaction kinetics. However, Ti and Ti based hydrogen storage alloys have been thought to be the third generation of alloys with a high hydrogen capacity, which makes it difficult to handle because of high reactivity. One of the most methods to develop kinetics was addition of transition metal. Therefore, Mg-Ti-Cr-Nb alloy was fabricated to add TiCrNb by hydrogen induced mechanical alloying. TiCrNb systems have included transition metals, low operating temperatures and hydrogen storage materials. As-received specimens were characterized using X-ray Diffraction analysis (XRD), Scanning Electron Microscopy (SEM) and Thermo Gravimetric analysis/Differential Scanning Calorimetry (TG/DSC). Mg-TiCr_10Nb systems were evaluated for hydrogen kinetics by Sievert’s type Pressure-Composition-Isotherm (PCI) equipment. The operating temperature range was 473, 523, 573 and 623 K.

TheoSSA - Model WD Spectra on Demand: The Impact of Ne, Na, Mg, and Iron-group Elements on the Balmer Lines

Science.gov (United States)

Reindl, N.; Rauch, T.

2015-06-01

The registered German Astrophysical Virtual Observatory (GAVO) service TheoSSA provides easy access to synthetic stellar spectra. This GAVO database contains already ten thousands of these, which were calculated with different chemical compositions of the elements H to Ni. In addition to the database, it is possible to calculate individual spectra for hot, compact stars based on the Tübingen NLTE Model-Atmosphere Package (TMAP) via the TMAW service. The TMAW models were, in the pilot phase, restricted to the elements H, He, C, N, and O. Now, TMAW is extended to additionally consider opacities from Ne, Na, and Mg. Soon, TMAW will also be able to include the opacities from the so-called iron-group elements (Ca - Ni). We describe the improvements and show the impact of Ne, Na, Mg, and iron-group elements on the Balmer lines.

Antioxidant vitamins C, E and coenzyme Q10 vs Dexamethasone: comparisons of their effects in pulmonary contusion model

Directory of Open Access Journals (Sweden)

Gokce Mertol

2012-09-01

Full Text Available Abstract Background The goal of our study is to evaluate the effects of antioxidant vitamins (vitamin C and E, Coenzyme Q10 (CoQ10 and dexamethasone (Dxm in experimental rat models with pulmonary contusion (PC. Methods Rats were randomly divided into six groups. Except for the control, all subgroups had a moderate pulmonary contusion. Animals in the group I and group II received intraperitoneal saline, group III received 10mg.kg-1 CoQ10 group IV received 100mg.kg-1 vitamin C, group V received 150mg.kg-1 vitamin E, and group VI received 10mg.kg-1 Dxm. Blood gas analysis, serum nitric oxide (NO and malondialdehyde (MDA levels as well as superoxide dismutase (SOD activity assays, bronchoalveolar lavage (BAL fluid and histopathological examination were performed. Results Administration of CoQ10 resulted in a significant increase in PaO2 values compared with the group I (p = 0.004. Levels of plasma MDA in group II were significantly higher than those in the group I (p = 0.01. Early administration of vitamin C, CoQ10, and Dxm significantly decreased the levels of MDA (p = 0.01. Lung contusion due to blunt trauma significantly decreased SOD activities in rat lung tissue compared with group I (p = 0.01. SOD levels were significantly elevated in animals treated with CoQ10, Vitamin E, or Dxm compared with group II (p = 0.01. Conclusions In our study, CoQ10, vitamin C, vitamin E and Dxm had a protective effect on the biochemical and histopathological outcome of PC after experimental blunt thorax trauma.

BLACK TEA INFUSION AMELIORATES ENZYMATIC CHANGES INDUCED BY SUBCUTANEOUS EXPOSURE OF GASOLINE AND GM-10 IN MICE

OpenAIRE

Manjeet Dave; Ramtej Jayram Verma

2017-01-01

The present study was carried out to examine the ameliorative effect of black tea infusion on gasoline and GM-10 induced enzymatic changes in kidney of mice. Eighty healthy adult Swiss strain male albino mice weighing 32-35 gm were divided into eight groups including untreated control and various treated groups. Treated groups were subcutaneously administered with gasoline (412 mg/kg/day) and GM-10 low dose (206 mg/kg/day) and high dose (412 mg/kg/day) for 30 days. Black tea infusion (2%) was...

Effects of graphite doping on critical current density and microstructure of MgB2 bulks by an improved Mg-diffusion method

International Nuclear Information System (INIS)

Pan, X.F.; Zhao, Y.; Feng, Y.; Yang, Y.; Cheng, C.H.

2008-01-01

abstract: A series of graphite-doped MgB 2 bulks with high density have been successfully prepared by an improved Mg-diffusion method in ambient pressure. The effects of graphite doping on lattice parameters, T c , J c and microstructure of MgB 2 have been investigated. The results show that compared to the nano-C-doped or CNTs-doped MgB 2 , C is not easy to substitute B in graphite-doped MgB 2 . However, at the same C content, the graphite-doped MgB 2 has a higher J c . At 10 K and self-field, the J c for MgB 1.985 C 0.015 reaches 0.58 MA/cm 2 . For the MgB 1.945 C 0.055 , at 5 K, 7 T and 10 K, 6 T the J c achieves 10,000 A/cm 2 which is two orders of magnitude higher than that for the undoped sample. In addition to improving electron scattering and intergranular connectivity, the unreacted graphite in the graphite-doped MgB 2 is proposed to be responsible to the excellent J c properties of MgB 2 in high fields, due to depressed grain growth and enhanced grain boundary flux pinning

Pinning in high performance MgB{sub 2} thin films and bulks: Role of Mg-B-O nano-scale inhomogeneities

Energy Technology Data Exchange (ETDEWEB)

Prikhna, Tatiana, E-mail: prikhna@mail.ru [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine); Shapovalov, Andrey [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine); Eisterer, Michael [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria); Shaternik, Vladimir [G.V. Kurdyumov Institute for Metal Physics of the National Academy of Sciences of Ukraine, 36 Academician Vernadsky blvd., Kiev, 03680 (Ukraine); Goldacker, Wilfried [Karlsruhe Institute of Technology (KIT), 76344 Eggenstein (Germany); Weber, Harald W. [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria); Moshchil, Viktor; Kozyrev, Artem; Sverdun, Vladimir [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine); Boutko, Viktor [Donetsk Institute for Physics and Engineering named after O.O. Galkin of the National Academy of Sciences of Ukraine, R. Luxemburg str.72, Donetsk-114, 83114 (Ukraine); Grechnev, Gennadiy [B. Verkin Institute for Low Temperature Physics of the National Academy of Sciences of Ukraine, 47, Prospekt Nauky, Kharkiv 61103 (Ukraine); Gusev, Alexandr [Donetsk Institute for Physics and Engineering named after O.O. Galkin of the National Academy of Sciences of Ukraine, R. Luxemburg str.72, Donetsk-114, 83114 (Ukraine); Kovylaev, Valeriy; Shaternik, Anton [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine)

2017-02-15

Highlights: • Pinning in MgB{sub 2} depends on the Mg-B-O nano-scaled inhomogeneities. • Finer oxygen-enriched inhomogeneities is the reason of the higher J{sub c} in MgB{sub 2} thin films as compared to bulk. • The results of DOS calculations for MgB{sub 2-x}O{sub x} compounds demonstrate that they have metal-like behavior. • Ordered oxygen distribution in MgB{sub 2} (in pairs or zigzags) reduces binding energy. - Abstract: The comparison of nano-crystalline MgB{sub 2} oxygen-containing thin film (140 nm) and highly dense bulk materials showed that the critical current density, J{sub c}, depends on the distribution of Mg-B-O nano-scale inhomogeneities. It has been shown that MgB{sub 2} bulks with high J{sub c} in low (∼10{sup 6} A/cm{sup 2} in 0-1 T at 10 K) and medium magnetic fields contain MgB{sub 0.6-0.8}O{sub 0.8-0.9} nano-inclusions, where δT{sub c} or a combined δT{sub c} (dominant) / δ{sub l} pinning mechanism prevails, while in bulk MgB{sub 2} with high J{sub c} in high magnetic fields (B{sub irr}(18.5 K) = 15 T, B{sub c2}(0 K) = 42.1 T) MgB{sub 1.2-2.7}O{sub 1.8-2.5} nano-layers are present and δ{sub l} pinning prevails. The structure of oxygen-containing films with high J{sub c} in low and high magnetic fields (J{sub c} (0 T) = 1.8 × 10{sup 7} A/cm{sup 2} and J{sub c} (5 T) = 2 × 10{sup 6} A/cm{sup 2} at 10 K) contains very fine oxygen-enriched Mg-B-O inhomogeneities and δ{sub l} pinning is realized. The results of DOS calculations in MgB{sub 2-x}O{sub x} cells for x = 0, 0.125, 0.25, 0.5, 1 demonstrate that all compounds are conductors with metal-like behaviour. In the case of ordered oxygen substitution for boron the binding energy, E{sub b}, does not increase sufficiently as compared with that for MgB{sub 2}, while when oxygen atoms form zigzag chains the calculated E{sub b} is even lower (E{sub b} = −1.15712 Ry).

Fabrication of a Scaled MgB2 Racetrack Demonstrator Pole for a 10-MW Direct-Drive Wind Turbine Generator

DEFF Research Database (Denmark)

Magnusson, Niklas; Eliassen, Jan Christian; Abrahamsen, Asger Bech

2018-01-01

Field windings made of MgB2 wires or tapes are considered for their potential to reduce volume, weight, and cost of large offshore wind turbine generators. To gain experience of how to use this relatively new material in full-scale generators, tests of different winding methodologies and techniques...... are needed. In this paper, we describe in detail the steps used to wind a racetrack coil with a length of 1 m and a width of 0.5 m out of 4.5 km of MgB2 superconducting tape. The width corresponds to a full-scale pole of a 10-MW generator, whereas the length of the straight section is shorter than...... the corresponding full-scale pole. The coil was built up of ten double pancake coils. Each double pancake coil was wet wound using a semiautomatic winding process, where Stycast 2850 was applied directly to the MgB2 tape without any other dedicated electrical insulation. The strengths and weaknesses of the winding...

[Comparison of 1 mg/body and 3 mg/body of intravenous granisetron for the prevention of chemotherapy-induced nausea and vomiting and adverse events in hematological malignancy patients].

Science.gov (United States)

Motohashi, Shinya; Hori, Katsuhito; Ono, Takaaki; Ohnishi, Kazunori; Kawakami, Junichi

2012-01-01

Granisetron is a selective 5-hydroxy tryptamine3 receptor antagonist and widely used for chemotherapy-induced nausea and vomiting (CINV). Recommended dose of intravenous granisetron in the USA and Europe has been set at 0.01 mg/kg (1 mg/body) in the antiemetic treatment guidelines established by the American Society of Clinical Oncology and National Comprehension Cancer Network. In contrast, the approved dose in Japan is 0.04 mg/kg (3 mg/body). Randomized controlled trials (RCTs) which compared 1 mg/body with 3 mg/body of intravenous granisetron for CINV had been reported in Japan. In these RCTs, however, hematological malignancy patients were excluded. We performed observational retrospective study to compare 1 mg/body with 3 mg/body of intravenous granisetron for the prevention of CINV and adverse events in hematological malignancy patients. Number of the patients and chemotherapy courses were 15 and 30 in the 1 mg/body group, and 15 and 27 in the 3 mg/body group, respectively. No nausea rates in the 1 and 3 mg/body group were 83% and 89% of courses, respectively. No vomiting rates in the 1 and 3 mg/body group were 97% and 100% of courses, respectively. The incidences of constipation in the 1 and 3 mg/body group were 34% and 45% of courses, respectively. Anaphylaxis and headache did not occur in both groups. Our findings suggested that 1 mg/body of intravenous granisetron can prevent from CINV in hematological malignancy patients, as well as 3 mg/body.

Randomised study of Casodex 50 MG monotherapy vs orchidectomy in the treatment of metastatic prostate cancer. The Scandinavian Casodex Cooperative Group

DEFF Research Database (Denmark)

Iversen, P; Tveter, K; Varenhorst, E

1996-01-01

The effect of Casodex (ICI 176,334), a new, once-daily, selective antiandrogen, given as 50 mg monotherapy, was compared with orchidectomy in a randomised, multicentre, open study in 376 patients with metastatic prostate cancer. At 3 months, PSA was reduced by 86% in the Casodex group and by 96......% in the orchidectomy group. Treatment failed in 51 patients in the orchidectomy group and 66 showed a subjective response. Treatment failed in 86 patients treated with Casodex and 40 patients showed a subjective response. Patients treated with Casodex maintained their sexual interest better than those...

Sorption of selenium on Mg-Al and Mg-Al-Eu layered double hydroxides

International Nuclear Information System (INIS)

Curtius, H.; Paparigas, Z.; Kaiser, G.

2008-01-01

Salt domes represent deep geological formations which are under consideration as final repositories for irradiated research reactor fuel elements. For long-term safety aspects the mobilisation of the radionuclides due to a water ingress is intensively investigated. At the Institute of Energy Research (IEF-6), leaching experiments were performed in a hot cell facility with UAl x -Al and U 3 Si 2 -Al dispersed research reactor fuel elements in repository-relevant MgCl 2 -rich salt brines under anaerobic conditions. The fuel plates corroded completely within one year and a Mg-Al-layered double hydroxide (LDH) with chloride as interlayer anion was identified as one crystalline phase component of the corrosion products (secondary phases). This Mg-Al-LDH was synthesized, characterized, and the ability to retard europium by an incorporation process was investigated. Europium, as a representative for lanthanides, was identified to be one of the radionuclides which were found in the corrosion products. We could show that europium was incorporated in the lattice structure. LDHs have high anion exchange capacities that enhance their potential to remove anionic contaminants from aqueous systems. In this work the sorption behaviour of selenium in the chemical form as selenite (SeO 3 2- ) on Mg-Al-LDH and on Mg-Al-Eu-LDH was investigated. Especially the influence of the larger europium-III ion was of interest. It represents in the Mg-Al-Eu-LDH about 10% of the molar aluminium amount. The sorption has been experimentally studied in a wide range of pH, ionic strength, radionuclide and sorbent concentration. Both LDHs with chloride as interlayer anion were synthesized by a coprecipitation method under controlled conditions, and their main physico-chemical properties were analyzed prior to the sorption experiments. The sorption kinetics of selenite on the LDHs in water and in MgCl 2 -rich brine were rapid using a LDH concentration of 10 g/L. Equilibrium, indicated by stable p

Synthesis of Mg(OH) 2, MgO, and Mg nanoparticles using laser ablation of magnesium in water and solvents

Science.gov (United States)

Phuoc, Tran X.; Howard, Bret. H.; Martello, Donald V.; Soong, Yee; Chyu, Minking K.

2008-11-01

Laser ablation of magnesium in deionized water (DW), solutions of DW and sodium dodecyl sulfate (SDS) with different concentrations, acetone and 2-propanol has been conducted. The results showed that ablation in acetone and 2-propanol yielded MgO and Mg nanocrystallites as isolated particles and agglomerated chains probably intermixed with organic residues resulting from the alteration/decomposition of the solvents under the high-energy conditions. Brucite-like Mg(OH) 2 particles were mainly produced by laser ablation of Mg in either DW or DW-SDS solutions. Ablation in DW yielded particles of fiber-like shapes having a diameter of about 5-10 nm and length as long as 150 nm. Materials produced in DW-SDS solutions were composed of various size and shape particles. Some had rough surfaces with irregular shapes. Small particles were about 20-30 nm and larger particles were about 120 nm. Particles with rod-like, triangular, and plate-like shapes were also observed.

Cytotoxic characteristics of biodegradable EW10X04 Mg alloy after Nd coating and subsequent heat treatment

Energy Technology Data Exchange (ETDEWEB)

Katarivas Levy, Galit [Department of Materials Engineering, Ben-Gurion University of the Negev, Beer-Sheva 84105 (Israel); Ventura, Yvonne [Department of Biotechnology Engineering, Ben-Gurion University of the Negev, Beer-Sheva 84105 (Israel); Goldman, Jeremy [Biomedical Engineering Department, Michigan Technological University, Houghton, MI 49931 (United States); Vago, Razi [Department of Biotechnology Engineering, Ben-Gurion University of the Negev, Beer-Sheva 84105 (Israel); Aghion, Eli [Department of Materials Engineering, Ben-Gurion University of the Negev, Beer-Sheva 84105 (Israel)

2016-05-01

Porous Mg scaffolds are considered as potential bone growth promoting materials. Unfortunately, the high rate of biocorrosion inherent to Mg alloys may cause a premature loss of mechanical strength, excessive evolution of hydrogen gas, and a rapidly shifting surface topography, all of which may hinder the ability of native cells to attach and grow on the implant surface. Here we investigated the cell cytotoxicity effects during corrosion of a novel magnesium alloy, EW10X04 (Mg–1.2%Nd–0.5%Y–0.5%Zr–0.4%Ca), following diffusion coating (DC) and heat treatment to reduce the corrosion rate. Cells were exposed either to corrosion products or to the corroding scaffold surface, in vitro. The microstructure characterization of the scaffold surface was carried out by scanning electron microscopy (SEM) equipped with a Noran energy dispersive spectrometer (EDS). Phase analyses were obtained by X-ray diffraction (XRD). We found that cell viability, growth, and adhesion were all improved when cultured on the EW10X04 + DC surface or under corrosion product extracts due to lower corrosion rates relative to the EW10X04 control samples. It is therefore believed that the tested alloy after Nd coating and heat treatment may introduce a good balance between its biodegradation characteristics and cytotoxic effects towards cells. - Highlights: • The effects of a diffusion coating (DC) with Nd on cell cytotoxicity is shown. • A novel EW10X04 (Mg–1.2%Nd–0.5%Y–0.5%Zr–0.4%Ca) magnesium alloy with DC was tested. • Cell viability, growth, and adhesion were reduced on the control vs. DC surface. • The DC alloy may introduce a good balance between biodegradation and cytotoxicity.

Cytotoxic characteristics of biodegradable EW10X04 Mg alloy after Nd coating and subsequent heat treatment

International Nuclear Information System (INIS)

Katarivas Levy, Galit; Ventura, Yvonne; Goldman, Jeremy; Vago, Razi; Aghion, Eli

2016-01-01

Porous Mg scaffolds are considered as potential bone growth promoting materials. Unfortunately, the high rate of biocorrosion inherent to Mg alloys may cause a premature loss of mechanical strength, excessive evolution of hydrogen gas, and a rapidly shifting surface topography, all of which may hinder the ability of native cells to attach and grow on the implant surface. Here we investigated the cell cytotoxicity effects during corrosion of a novel magnesium alloy, EW10X04 (Mg–1.2%Nd–0.5%Y–0.5%Zr–0.4%Ca), following diffusion coating (DC) and heat treatment to reduce the corrosion rate. Cells were exposed either to corrosion products or to the corroding scaffold surface, in vitro. The microstructure characterization of the scaffold surface was carried out by scanning electron microscopy (SEM) equipped with a Noran energy dispersive spectrometer (EDS). Phase analyses were obtained by X-ray diffraction (XRD). We found that cell viability, growth, and adhesion were all improved when cultured on the EW10X04 + DC surface or under corrosion product extracts due to lower corrosion rates relative to the EW10X04 control samples. It is therefore believed that the tested alloy after Nd coating and heat treatment may introduce a good balance between its biodegradation characteristics and cytotoxic effects towards cells. - Highlights: • The effects of a diffusion coating (DC) with Nd on cell cytotoxicity is shown. • A novel EW10X04 (Mg–1.2%Nd–0.5%Y–0.5%Zr–0.4%Ca) magnesium alloy with DC was tested. • Cell viability, growth, and adhesion were reduced on the control vs. DC surface. • The DC alloy may introduce a good balance between biodegradation and cytotoxicity.

On the Selective Laser Melting (SLM of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties

Directory of Open Access Journals (Sweden)

Francesco Trevisan

2017-01-01

Full Text Available The aim of this review is to analyze and to summarize the state of the art of the processing of aluminum alloys, and in particular of the AlSi10Mg alloy, obtained by means of the Additive Manufacturing (AM technique known as Selective Laser Melting (SLM. This process is gaining interest worldwide, thanks to the possibility of obtaining a freeform fabrication coupled with high mechanical properties related to a very fine microstructure. However, SLM is very complex, from a physical point of view, due to the interaction between a concentrated laser source and metallic powders, and to the extremely rapid melting and the subsequent fast solidification. The effects of the main process variables on the properties of the final parts are analyzed in this review: from the starting powder properties, such as shape and powder size distribution, to the main process parameters, such as laser power and speed, layer thickness, and scanning strategy. Furthermore, a detailed overview on the microstructure of the AlSi10Mg material, with the related tensile and fatigue properties of the final SLM parts, in some cases after different heat treatments, is presented.

On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties.

Science.gov (United States)

Trevisan, Francesco; Calignano, Flaviana; Lorusso, Massimo; Pakkanen, Jukka; Aversa, Alberta; Ambrosio, Elisa Paola; Lombardi, Mariangela; Fino, Paolo; Manfredi, Diego

2017-01-18

The aim of this review is to analyze and to summarize the state of the art of the processing of aluminum alloys, and in particular of the AlSi10Mg alloy, obtained by means of the Additive Manufacturing (AM) technique known as Selective Laser Melting (SLM). This process is gaining interest worldwide, thanks to the possibility of obtaining a freeform fabrication coupled with high mechanical properties related to a very fine microstructure. However, SLM is very complex, from a physical point of view, due to the interaction between a concentrated laser source and metallic powders, and to the extremely rapid melting and the subsequent fast solidification. The effects of the main process variables on the properties of the final parts are analyzed in this review: from the starting powder properties, such as shape and powder size distribution, to the main process parameters, such as laser power and speed, layer thickness, and scanning strategy. Furthermore, a detailed overview on the microstructure of the AlSi10Mg material, with the related tensile and fatigue properties of the final SLM parts, in some cases after different heat treatments, is presented.

Perbandingan Pemberian Ondansetron 8 mg dengan Tramadol 1 mg/ kgBB Intravena untuk Mencegah Menggigil Pascaanestesi Umum pada Operasi Mastektomi Radikal atau Modifikasi

Directory of Open Access Journals (Sweden)

Mirza Oktavian

2014-04-01

Full Text Available ost anesthetic shivering is a common complication of general anesthesia and preventable with several types of drugs. The aim of this study was to compare the efficacy of intravenous 8mg ondansetron versus tramadol 1 mg/kgBW in preventing post anesthetic shivering after general anesthesia. The research is a prospective, randomized double-blind controlled study involving 38 female patients aged 30–65 years at Dr. Hasan Sadikin Hospital Bandung period March–April 2012, American Society of Anesthesiologist (ASA physical status I–II, who underwent radical or modified mastectomy. Subjects were randomly divided into two groups. One group was given ondansetron 8 mg and the other group was given tramadol 1 mg/kgBW before surgical wound closure. Research results showed that incidence of post anesthetic shivering was less on tramadol group (15.8% compared to ondansetron (52.6% group, which is statistically significant (p<0.05. In conclusion, administration of tramadol 1 mg/kgBW intravenously is more effective in preventing post anesthetic shivering in radical or modified mastectomy.

[Effects of different concentrations of MgSiF(6) as electrolyte for micro-arc oxidation on the bond strength between titanium and porcelain].

Science.gov (United States)

Yuan, M J; Zhang, S J; Liu, J; Tan, F

2018-02-09

Objective: To investigate the effects of different concentrations of MgSiF(6) as electrolyte on the bond strength between titanium and porcelain after micro-arc oxidation (MAO) treatment and screen the suitable concentration of MgSiF(6) that can improve the bond strength between titanium and porcelain. Methods: Four different concentrations of MgSiF(6) (10, 20, 30, 40 g/L) were chosen as MAO reaction solutions. Sandblasting treatment was selected as a control group. After porcelain was fused to each specimen, titanium-porcelain bond strengths were evaluated by the three-point bending test according to ISO 9693. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) were adopted to evaluate the morphologies and elemental compositions of both the MAO coatings and the interfaces of the titanium-porcelain restoration. Results: The surface of titanium specimen in the control group was sharp and rough, while specimens in both 10 g/L group and 20 g/L group were porous and homogeneous. However, the pores found on the specimens in the latter group were larger in diameter (approximately 1.0-2.0 μm) than those on the former one (0.2-0.5 μm). The bond strengths of the control group and the experimental groups (10, 20, 30, 40 g/L MgSiF(6)) were (27.08±3.16), (38.18±2.65), (44.75±2.21), (36.44±2.04), (31.04±2.59) MPa, respectively. All the experimental groups showed higher bond strengths than the control group did ( Pporcelain were tight and compact in the 20 g/L group, while different amounts of pores and cracks were visible in the other groups. Additionally, after the three-point bending test, few residual porcelains could be observed on the surfaces of specimens in the control group. Conclusions: MAO treatment with 20 g/L MgSiF(6) on titanium can improve bonding strength between titanium and porcelain.

Effects of graphite doping on critical current density and microstructure of MgB{sub 2} bulks by an improved Mg-diffusion method

Energy Technology Data Exchange (ETDEWEB)

Pan, X.F. [Key Laboratory of Magnetic Levitation and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhao, Y. [Key Laboratory of Magnetic Levitation and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney 2052, NSW (Australia)], E-mail: yshao@home.swjtu.edu.cn; Feng, Y. [Northwest Institute for Nonferrous Metal Research, P.O. Box 51, Xi' an, Shaanxi 710016 (China); Western Superconductivity Technology Company, Xi' an (China); Yang, Y. [Key Laboratory of Magnetic Levitation and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Cheng, C.H. [Key Laboratory of Magnetic Levitation and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney 2052, NSW (Australia)

2008-09-15

abstract: A series of graphite-doped MgB{sub 2} bulks with high density have been successfully prepared by an improved Mg-diffusion method in ambient pressure. The effects of graphite doping on lattice parameters, T{sub c}, J{sub c} and microstructure of MgB{sub 2} have been investigated. The results show that compared to the nano-C-doped or CNTs-doped MgB{sub 2}, C is not easy to substitute B in graphite-doped MgB{sub 2}. However, at the same C content, the graphite-doped MgB{sub 2} has a higher J{sub c}. At 10 K and self-field, the J{sub c} for MgB{sub 1.985}C{sub 0.015} reaches 0.58 MA/cm{sup 2}. For the MgB{sub 1.945}C{sub 0.055}, at 5 K, 7 T and 10 K, 6 T the J{sub c} achieves 10,000 A/cm{sup 2} which is two orders of magnitude higher than that for the undoped sample. In addition to improving electron scattering and intergranular connectivity, the unreacted graphite in the graphite-doped MgB{sub 2} is proposed to be responsible to the excellent J{sub c} properties of MgB{sub 2} in high fields, due to depressed grain growth and enhanced grain boundary flux pinning.

Comparison Study on Additive Manufacturing (AM) and Powder Metallurgy (PM) AlSi10Mg Alloys

Science.gov (United States)

Chen, B.; Moon, S. K.; Yao, X.; Bi, G.; Shen, J.; Umeda, J.; Kondoh, K.

2018-02-01

The microstructural and mechanical properties of AlSi10Mg alloys fabricated by additive manufacturing (AM) and powder metallurgy (PM) routes were investigated and compared. The microstructures were examined by scanning electron microscopy assisted with electron-dispersive spectroscopy. The crystalline features were studied by x-ray diffraction and electron backscatter diffraction. Room-temperature tensile tests and Vickers hardness measurements were performed to characterize the mechanical properties. It was found that the AM alloy had coarser Al grains but much finer Si precipitates compared with the PM alloy. Consequently, the AM alloy showed more than 100% increment in strength and hardness compared with the PM alloy due to the presence of ultrafine forms of Si, while exhibiting moderate ductility.

Evaluating Motoric Performance of 10 - 12 Age Group Football Players

Directory of Open Access Journals (Sweden)

Mehmet KUMARTAŞLI

2014-08-01

Full Text Available The aim of this study is to evaluate motoric perfromance of 10 - 12 age group football players. Akdeniz University tiny football team joined as experiment group and 80. Yıl Cumhuriyet Grammar School football team joined to the study as control group. An exercise programme with educational game format considering physical capacities and develeopment features was applied to the student as 8 weeks, 3 days a week. Standing long jump, flexibilty, 20 m. speed, handgrip strength, arm pull, vert ical jump, 10x5 shuttle run and leg strength tests were applied to the students. Handled data were compared at SPSS 10 statistic programme by using Independent Sample t Test. Students’ lenght and weight measurements were calculated. As a result of measurem ents, there were not found diffrences between experimental and control group’s standing long jump, flexibilty, 20 m. speed, handgrip strength, a vertical jump, 10x5 shuttle run and leg strength tests (p>0,05; but in arm pull test, statistically difference was found (p<0,01. While evaluating the physical performance in cihldren and adolescents, growth process is had to be considered. The results of football players that exercise regularly from small ages at physical and physiologic measurements have an importance according to their age. Performance observed in children is sudden and temporary. There are a few studies in the literature about negative psycological effects of starting trainings in early ages.

Properties of thymidylate synthetase from Ehrlich ascites carcinoma cells. Effect of Mg2/ and MgATP2-.

Science.gov (United States)

Jastreboff, M; Kedzierska, B; Rode, W

1982-01-15

Ehrlich ascites carcinoma thymidylate synthetase was purified to electrophoretic homogeneity by affinity chromatography on 10-formyl-5,8-dideazofolate-ethyl-Sepharose. Electrophoretic analysis of the formation of the enzyme-5-fluorodeoxyuridylate-5,10-methylenetetrahydrofolate complexes showed the presence of two binding sites for 5-fluorodeoxyuridylate on the enzyme molecule. Molecular weight of the native enzyme was found to be 78,5000, whereas that of its monomer was 38, 500. The apparent Michaelis constants for dUMP and (+/-)-L-5,10-methylenetetrahydrofolate were 1.3 +/- 0.4 and 32.2 +/- 0.7 micrometers respectively. Phosphate acted as a weak inhibitor, competitive toward dUMP. The enzyme reaction exhibited a temperature-dependent change of activation energy, reflected in the binding affinity of dUMP, with a transitional temperature of 35.8 degrees. Both Mg2+ and MgATP2- were strong activators of the enzyme, MgATP2- being more effective.

Instability of TiC and TiAl3 compounds in Al-10Mg and Al-5Cu alloys by addition of Al-Ti-C master alloy

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The performance of Al-Ti-C master alloy in refining Al-10Mg and A1-5Cu alloys was studied by using electron probe micro-analyzer (EPMA) and X-ray diffractometer (XRD) analysis.The results indicate that there are obvious fading phenomena in both Al-10Mg and Al-5Cu alloys with the addition of Al-5Ti-0.4C refiner which contains TiC and TiAl3 compounds.Mg element has no influence on the stability of TiC and TiAl3, while TiC particles in Al-10Mg alloy react with Al to form Al4C3 particles, resulting in the refinement fading.However, TiC particles are relatively stable in Al-5Cu alloy, while TiAl3 phase reacts with Al2Cu to produce a new phase Ti(Al, Cu)2, which is responsible for the refinement fading in Al-5Cu alloy.These indicate that the refinement fading will not occur only when both the TiC particles and TiAl3 compound of Al-Ti-C refiner are stable in Al alloys.

Prussian Blue Mg-Li Hybrid Batteries.

Science.gov (United States)

Sun, Xiaoqi; Duffort, Victor; Nazar, Linda F

2016-08-01

The major advantage of Mg batteries relies on their promise of employing an Mg metal negative electrode, which offers much higher energy density compared to graphitic carbon. However, the strong coulombic interaction of Mg 2+ ions with anions leads to their sluggish diffusion in the solid state, which along with a high desolvation energy, hinders the development of positive electrode materials. To circumvent this limitation, Mg metal negative electrodes can be used in hybrid systems by coupling an Li + insertion cathode through a dual salt electrolyte. Two "high voltage" Prussian blue analogues (average 2.3 V vs Mg/Mg 2+ ; 3.0 V vs Li/Li + ) are investigated as cathode materials and the influence of structural water is shown. Their electrochemical profiles, presenting two voltage plateaus, are explained based on the two unique Fe bonding environments. Structural water has a beneficial impact on the cell voltage. Capacities of 125 mAh g -1 are obtained at a current density of 10 mA g -1 (≈C/10), while stable performance up to 300 cycles is demonstrated at 200 mA g -1 (≈2C). The hybrid cell design is a step toward building a safe and high density energy storage system.

Investigations on FCAM-III (Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36): A new homologue of the aenigmatite structure-type in the system CaO-MgO-Fe2O3-Al2O3

Science.gov (United States)

Zöll, Klaus; Kahlenberg, Volker; Krüger, Hannes; Tropper, Peter

2018-02-01

In the course of a systematic study of a part of the quaternary system Fe2O3-CaO-Al2O3-MgO (FCAM) the previously unknown compound Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 (FCAM-III) has been synthesized. By analogy with the so-called SFCA series [1-5], our investigation in the system of FCAM shows the existence of a stoichiometric homologous series M14+6nO20+8n, where M = Fe, Ca, Al, Mg and n = 1 or 2. In air, we can prove the formation of coexisting FCAM-III and FCAM-I solid solutions at 1400 °C. By increasing the temperature up to 1425 °C FCAM-I disappears completely and FCAM-III co-exists with magnesiumferrite and a variety of calcium iron oxides. At 1450 °C FCAM-III breaks down to a mixture of FCAM-I again as well as magnesioferrite and melt. Small single-crystals of FCAM-III up to 35 μm in size could be retrieved from the 1425 °C experiment and were subsequently characterized using electron microprobe analysis and synchroton X-ray single-crystal diffraction. Finally the Fe2+/Fetot ratio was calculated from the total iron content based on the crystal-chemical formula obtained from EMPA measurements and charge balance considerations. FCAM-III or Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 has a triclinic crystal structure (space group P 1 ̅). The basic crystallographic data are: a = 10.223(22) Å, b = 10.316(21) Å, c = 14.203(15) Å, α = 93.473(50)°, β = 107.418(67)°, γ = 109.646(60)°, V = 1323.85(2) ų, Z = 1. Using Schreinemaker's technique to analyze the phase relations in the system Fe2O3-CaO-Al2O3-MgO it was possible to obtain the semi-quantitative stability relations between the participating phases and construct a topologically correct phase sequence as a function of T and fO2. The analysis shows that Ca2Al0.5Fe1.5O5 (C2A0.25F0.75) and CaAl1.5Fe2.5O7 (CA0.75F1.25) with higher calculated Fe2+ contents are preferably formed at lower oxygen fugacity and react to CaAl0.5Fe1.5O4 (CA0.25F0.75) by increasing fO2. Spinel-type magnesium

Pitavastatin 4 mg Provides Significantly Greater Reduction in Remnant Lipoprotein Cholesterol Compared With Pravastatin 40 mg: Results from the Short-term Phase IV PREVAIL US Trial in Patients With Primary Hyperlipidemia or Mixed Dyslipidemia.

Science.gov (United States)

Miller, P Elliott; Martin, Seth S; Joshi, Parag H; Jones, Steven R; Massaro, Joseph M; D'Agostino, Ralph B; Sponseller, Craig A; Toth, Peter P

2016-03-01

Remnants are partially hydrolyzed, triglyceride-rich lipoproteins that are implicated in atherosclerosis. We assessed the adequacy of pitavastatin 4 mg and pravastatin 40 mg in reducing atherogenic lipid parameters beyond LDL-C, in particular remnant lipoprotein cholesterol (RLP-C). From the Phase IV, multicenter, randomized, double-blind PREVAIL US (A Study of Pitavastatin 4 mg Vs. Pravastatin 40 mg in Patients With Primary Hyperlipidemia or Mixed Dyslipidemia) trial, we examined lipoprotein cholesterol subfractions using Vertical Auto Profile testing and apolipoproteins B and A-I at baseline and 12 weeks. Participants with primary hyperlipidemia or mixed dyslipidemia had LDL-C levels of 130 to 220 mg/dL and triglyceride levels ≤ 400 mg/dL. In this post hoc analysis, changes in lipid parameters were compared by using ANCOVA. Lipoprotein subfraction data were available in 312 patients (pitavastatin, n = 157; pravastatin, n = 155). Pitavastatin promoted a greater reduction in RLP-C than pravastatin (-13.6 [8.7] vs -9.3 [9.5] mg/dL). Furthermore, the pitavastatin group reported greater reductions in both components of RLP-C (both, P < 0.001): intermediate-density lipoprotein cholesterol (-9.5 [6.3] vs -6.4 [6.6] mg/dL) and very low-density lipoprotein cholesterol subfraction 3 (-4.1 [3.5] vs -2.9 [3.8] mg/dL). There were also greater reductions in the major ratios of risk (apolipoprotein B/apolipoprotein A-I and total cholesterol/HDL-C) (both, P < 0.001). There were no significant changes in HDL-C, its subfractions, or natural log lipoprotein(a)-cholesterol. The mean age was 58.8 ± 8.9 years in the pitavastatin group and 57.0 ± 10.2 years in the pravastatin group. Compared with pravastatin 40 mg daily, pitavastatin 4 mg provided superior reductions in atherogenic lipid parameters beyond LDL-C, including RLP-C. Future studies are needed investigate the clinical implications of lowering directly measured RLP-C as the principal target. ClinicalTrials.gov identifier

Synthesis of Mg(OH)₂, MgO, and Mg nanoparticles using laser ablation of magnesium in water and solvents

Energy Technology Data Exchange (ETDEWEB)

Phuoc, Tran X. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Howard, Bret. H. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Martello, Donald V. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Soong, Yee [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Chyu, Minking K. [Univ. of Pittsburgh, PA (United States)

2008-11-01

Laser ablation of magnesium in deionized water (DW), solutions of DW and sodium dodecyl sulfate (SDS) with different concentrations, acetone and 2-propanol has been conducted. The results showed that ablation in acetone and 2-propanol yielded MgO and Mg nanocrystallites as isolated particles and agglomerated chains probably intermixed with organic residues resulting from the alteration/decomposition of the solvents under the high-energy conditions. Brucite-like Mg(OH)₂ particles were mainly produced by laser ablation of Mg in either DW or DW-SDS solutions. Ablation in DW yielded particles of fiber-like shapes having a diameter of about 5-10nm and length-as long as 150 nm. Materials produced in DW-SDS solutions were composed of various size and shape particles. Some had rough surfaces with irregular shapes. Small particles were about 20-30 nm and larger particles were about 120 nm. Particles with rodlike, triangular, and plate-like shapes were also observed.

Sol-Gel synthesis of MgO-SiO2 glass compositions having stable liquid-liquid immiscibility

Science.gov (United States)

Bansal, Narottam P.

1987-01-01

MgO-SiO2 glasses containing up to 15 mol % MgO, which could not have been prepared by the conventional glass melting method due to the presence of stable liquid-liquid immiscibility, were synthesized by the sol-gel technique. Clear and transparent gels were obtained from the hydrolysis and polycondensation of silicon tetraethoxide (TEOS) and magnesium nitrate hexahydrate when the water/TEOS mole ratio was four or more. The gelling time decreased with increase in magnesium content, water/TEOS ratio, and reaction temperature. Magnesium nitrate hexahydrate crystallized out of the gels containing 15 and 20 mol % MgO on slow drying. This problem was partially alleviated by drying the gels quickly at higher temperatures. Monolithic gel samples were prepared using glycerol as the drying control additive. The gels were subjected to various thermal treatments and characterized by several methods. No organic groups could be detected in the glasses after heat treatments to approx. 800 C, but trace amounts of hydroxyl groups were still present. No crystalline phase was found from X-ray diffraction in the gel samples to approx. 890 C. At higher temperatures, alpha quartz precipitated out as the crystalline phase in gels containing up to 10 mol % MgO. The overall activation energy for gel formation in 10MgO-90SiO2 (mol %) system for water/TEOS mole ratio of 7.5 was calculated to be 58.7 kJ/mol.

SIMS and Raman studies of Mg-doped InN

International Nuclear Information System (INIS)

Davydov, V.Yu.; Kitaev, Yu.E.; Smirnov, A.N.; Lundina, E.Y.; Klochikhin, A.A.; Smirnov, M.B.; Lu, Hai; Schaff, William J.; Lee, H.M.; Lin, H.W.; Hong, Y.L.; Gwo, S.

2008-01-01

Raman and SIMS studies of Mg-doped InN films with a Mg content from N Mg =3.3 x 10 19 to 5.5 x 10 21 cm -3 are reported. Lattice dynamics of hexagonal InN with substitutional impurities and vacancies has been investigated theoretically and calculated Raman spectra were compared with experimental ones. It is concluded that Raman spectroscopy is a good tool for quantitative characterization of Mg-doped InN. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Determination of mineral constituents in duplicate portion diets of two university student groups by instrumental neutron activation

International Nuclear Information System (INIS)

Maihara, V.A.; Favaro, D.I.T.; Silva, V.N.; Cunha, I.I.L.; Vasconcellos, M.B.A.; Gonzaga, I.B.; Silva, V.L.; Cozzolino, S.M.F.

2001-01-01

Concentrations of 15 elements were determined simultaneously in duplicate portion diets of two university student groups from Sao Paulo University consisting of nine women (20-23 years) and ten men (20-24 years). The diet samples were prepared by either freeze-drying or drying in a ventilated oven. About 100-200 mg of diets were irradiated for 2 minutes and 8 hours in the IEA-R1 m research reactor and Br, Ca, Cl, Co, Cr, Cs, K, Fe, Mn, Mg, Mo, Na, Rb, Se, and Zn were determined by instrumental neutron activation analysis (INAA). The average daily intakes found in the women and men groups were: 2.1 and 4.3 mg of Br, 501 and 707 mg of Ca; 3.1 and 6.0g of Cl; 12 and 25 mg of Co; 15 and 36μg of Cs; 53 and 63μg of Cr; 5.1 and 10.8 mg of Fe; 1.3 and 2.8 g of K; 134 and 306 mg of Mg; 1,3 and 4.1 mg of Mn; 134 and 302 mg of Mo, 2.0 and 4.1 g of Na; 2.4 and 4.6 mg of Rb; 29 and 41μg of Se; 6.2 and 10.6 mg of Zn, respectively. The daily intakes of Ca, Se and Zn in both groups and Fe in the women groups appeared to be below the U.S. RDA recommendations. For the elements Na and Cl the daily intakes were higher than the recommended values by RDA. (author)

Single dose (400 mg) versus 7 day (200 mg) daily dose itraconazole in the treatment of tinea versicolor: a randomized clinical trial.

Science.gov (United States)

Wahab, M A; Ali, M E; Rahman, M H; Chowdhury, S A; Monamie, N S; Sultana, N; Khondoker, L

2010-01-01

Tinea (pityriasis) versicolor is a superficial fungal infection and one of the most commonly found pigmentary disorders of skin caused by the yeast Malassezia. Multiple topical as well as systemic therapies are available for treatment. Systemic therapies are used for extensive disease, frequent relapse or where topical agents have failed. The aim that translates the rationale of the study was to compare the efficacy, safety, tolerability and cost effectiveness of single dose 400mg versus 7 day 200 mg daily dose of itraconazole in the treatment of tinea versicolor. A clinical study was done to compare the efficacy of single dose (400 mg) of itraconazole and 7 day 200 mg daily dose of itraconazole in the treatment of extensive tinea versicolor. Total 60 patients (aged 18-50 years) were selected for the study during the period of June 2007 to May 2008 in the department of Dermatology of three different hospitals in Bangladesh. Cases having with extensive involvement, diagnosed clinically and confirmed by wood's lamp and KOH microscopy were taken. Patients were randomly allocated into equal groups. Group A was given single dose 400 mg itraconazole and Group B was given 7 day 200 mg daily itraconazole. Fifty three (88%) male and 7(12%) female were included in the study. The mean age of group A was 32.37+/-9 years and in group B 33.23+/-8 years. The mean duration of the disease in group A was 2.63+/-2 months and 2.76+/-2 months in group B. In group A clinical responders was found cure 22(73.33%) and improvement 5(16.33%) and in group B it was found cure 24(79.99%) and improvement 4(13.33%). The measure at the End point (EP1) equals to 90% response and in-group B it was found cure 24 (79.99%) and improvement 4(13.33%). (Here the End point EP2) equals to 93.33%. The EP clinical analysis however shows 91.66% response. Both single dose and 7 day daily dose of itraconazole can be effective in the treatment of tinea versicolor with extensive involvement but single dose appears

A better cure rate with 800 mg than with 400 mg clarithromycin regimens in one-week triple therapy for Helicobacter pylori infection in cigarette-smoking peptic ulcer patients.

Science.gov (United States)

Ishioka, Hidehiko; Mizuno, Motowo; Take, Susumu; Ishiki, Kuniharu; Nagahara, Yasuhiro; Yoshida, Tomowo; Okada, Hiroyuki; Yokota, Kenji; Oguma, Keiji

2007-01-01

In Helicobacter pylori eradication therapy, using a proton pump inhibitor plus amoxicillin and clarithromycin (PPI/AC regimen), the impact of the clarithromycin dose and smoking on efficacy is conflicting. Here, we compared the efficacy of 400 and 800 mg of clarithromycin in the regimen in relation to smoking in patients with peptic ulcer disease. We studied 601 H. pylori-positive patients with peptic ulcer disease who had received amoxicillin 750 mg and clarithromycin 200 or 400 mg together with lansoprazole 30 mg b.i.d. 305 patients were treated with a regimen containing 400 mg of clarithromycin (C400 group), and 296 patients with a regimen containing 800 mg (C800 group). Overall cure rates between the two groups were not significantly different, but the cure rate in the C800 group was significantly better than that in the C400 group among patients infected with clarithromycin-sensitive strains (p = 0.03). This difference could be attributed to differences among smokers versus non-smokers: the cure rate among smokers in the C800 group (91.0%) was better than that in the C400 group (80.0%, p = 0.003). 800 mg of clarithromycin is recommended in the PPI/AC regimen for patients who smoke and are infected with clarithromycin-sensitive H. pylori. 2007 S. Karger AG, Basel

Clinical Efficacy and Residue Depletion of 10% Enrofloxacin Enteric-Coated Granules in Pigs

Directory of Open Access Journals (Sweden)

Zhixin Lei

2017-05-01

Full Text Available A new, more palatable formulation of 10% enrofloxacin enteric-coated granules was investigated to evaluate the pharmacokinetic effect in plasma, the residue elimination in tissues and the clinical efficacy against Actinobacillus pleuropneumonia (APP and Mycoplasam suis (MS in pigs. In this study, the enrofloxacin concentrations in plasma and tissues were detected using high-performance liquid chromatography with phosphate buffer (pH = 3 and acetonitrile. The pharmacokinetics and elimination of enrofloxacin enteric-coated granules were performed after oral administration at a single dose of 10 mg/kg body weight (bw and 5 mg/kg twice per day for 5 consecutive days, respectively. The in vivo antibacterial efficacy and clinical effectiveness of enrofloxacin enteric-coated granules against APP and MS were assayed at 2.5, 5, 10 mg/kg, compared with tiamulin (8 mg/kg based on establishment of APP and MS infection models. 56 APP strains were selected and tested for in vitro antibacterial activity of enrofloxacin enteric-coated granules. The main parameters of elimination half-life (t1/2β, Tmax, and area under the curve (AUC were 14.99 ± 4.19, 3.99 ± 0.10, and 38.93 ± 1.52 μg h/ml, respectively, revealing that the enrofloxacin concentration remained high and with a sustainable distribution in plasma. Moreover, the analysis on the evaluation of enrofloxacin and ciprofloxacin in muscle, fat, liver and kidney showed that the recovery were more than 84% recovery in accordance with the veterinary drug residue guidelines of United States pharmacopeia, and the withdrawal periods were 4.28, 3.81, 4.84, and 3.51 days, respectively, suggesting that the withdrawal period was 5 d after oral administration of 5 mg/kg twice per day. The optimal dosage of enrofloxacin enteric-coated granules against APP and MS was 5 mg/kg, with over 90% efficacy, which was significantly different (p < 0.05 to the 2.5 mg/kg group, but not to the 10 mg/kg group or the positive

7 CFR 3415.10 - Establishment and operation of peer review groups.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Establishment and operation of peer review groups... ASSESSMENT RESEARCH GRANTS PROGRAM Scientific Peer Review of Research Grant Applications § 3415.10 Establishment and operation of peer review groups. Subject to § 3415.5, the Administrator shall adopt procedures...

7 CFR 3400.10 - Establishment and operation of peer review groups.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Establishment and operation of peer review groups... GRANTS PROGRAM Scientific Peer Review of Research Grant Applications § 3400.10 Establishment and operation of peer review groups. Subject to § 3400.5, the Administrator will adopt procedures for the...

7 CFR 3411.10 - Establishment and operation of peer review groups.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Establishment and operation of peer review groups... INITIATIVE COMPETITIVE GRANTS PROGRAM Scientific Peer Review of Research Grant Applications § 3411.10 Establishment and operation of peer review groups. Subject to § 3411.5, the Administrator shall adopt procedures...

Effects of MgO impurities and micro-cracks on the critical current density of Ti-sheathed MgB2 wires

International Nuclear Information System (INIS)

Liang, G.; Alessandrini, M.; Yen, F.; Hanna, M.; Fang, H.; Hoyt, C.; Lv, B.; Zeng, J.; Salama, K.

2007-01-01

Ti-sheathed monocore MgB 2 wires with improved magnetic critical current density (J c ) have been fabricated by in situ powder-in-tube (PIT) method and characterized by magnetization, X-ray diffraction, scanning electron microscopy and electrical resistivity measurements. For the best wire, the magnetic J c values at 5 K and fields of 2 T, 5 T, and 8 T are 4.1 x 10 5 A/cm 2 , 7.8 x 10 4 A/cm 2 , and 1.4 x 10 4 A/cm 2 , respectively. At 20 K and fields of 0.5 T and 3 T, the J c values are about 3.6 x 10 5 A/cm 2 and 3.1 x 10 4 A/cm 2 , respectively, which are much higher than those of the Fe-sheathed mono-core MgB 2 wires fabricated with the same in situ PIT process and under the same fabricating conditions. It appears that the overall J c for the average Ti-sheathed wires is comparable to that of the Fe-sheathed wires. Our X-ray diffraction and scanning electron microscopy analysis indicates that J c in the Ti-sheathed MgB 2 wires can be strongly suppressed by MgO impurities and micro-cracks

Effects of carbon concentration and filament number on advanced internal Mg infiltration-processed MgB2 strands

International Nuclear Information System (INIS)

Li, G Z; Sumption, M D; Zwayer, J B; Susner, M A; Collings, E W; Rindfleisch, M A; Thong, C J; Tomsic, M J

2013-01-01

In this paper we show that an advanced internal Mg infiltration method (AIMI) is effective in producing superconducting wires containing dense MgB 2 layers with high critical current densities. The in-field critical current densities of a series of AIMI-fabricated MgB 2 strands were investigated in terms of C doping levels, heat treatment (HT) time and filament numbers. The highest layer J c for our monofilamentary AIMI strands was 1.5 × 10 5 A cm −2 at 10 T, 4.2 K, when the C concentration was 3 mol% and the strand was heat-treated at 675 ° C for 4 h. Transport critical currents were also measured at 4.2 K on short samples and 1 m segments of 18-filament C doped AIMI strands. The layer J c s reached 4.3 × 10 5 A cm −2 at 5 T and 7.1 × 10 4 A cm −2 at 10 T, twice as high as those of the best powder-in-tube strands. The analysis of these results indicates that the AIMI strands, possessing both high layer J c s and engineering J e s after further optimization, have strong potential for commercial applications. (paper)

Pharmacokinetic and pharmacodynamic evaluations of a 10 mg/kg enrofloxacin intramuscular administration in bearded dragons (Pogona vitticeps): a preliminary assessment.

Science.gov (United States)

Salvadori, M; Vercelli, C; De Vito, V; Dezzutto, D; Bergagna, S; Re, G; Giorgi, M

2017-01-01

Enrofloxacin (E) is commonly used in veterinary medicine. It is necessary to perform pharmacokinetic/dynamic studies to minimize the selection of resistant mutants of bacteria and extend the efficacy of antimicrobial agents. Eight healthy adult Pogona vitticeps were assigned into two groups of equal size and treated with a single intramuscular injection of E at 10 mg/kg. Blood samples were withdrawn at different scheduled times for each group, and rectal swabs were collected. E and ciprofloxacin (active metabolite) blood concentrations were quantified by an HPLC validated method, while the in vitro antimicrobial susceptibility was evaluated by the Kirby-Bauer disc diffusion susceptibility test. The pharmacokinetic profiles of E gave similar pharmacokinetic parameters irrespective of the collection time schedule. Bacteria isolation showed the presence of both E. coli, Salmonella enterica subspecies enterica and subspecies 3a, Proteus spp., and Pseudomonas spp. The majority of isolated colonies were sensitive to E, but the treatment did not reduce the number of bacteria in faeces. Results suggest that E is able to reach blood concentrations high enough to kill susceptible bacteria (MIC < 0.9 μg/mL), but at the same time does not significantly affect intestinal bacteria. © 2016 John Wiley & Sons Ltd.

Evaluation of Anticonvulsive ٍEffect of Magnesium Oxide Nanoparticles in Comparison with Conventional MgO in Diabetic and Non-diabetic Male Mice

Directory of Open Access Journals (Sweden)

Leila Jahangiri

2014-05-01

Full Text Available Introduction: Some studies show magnesium has anticonvulsive effect in some animal models. Despite of the availability of well-studied anticonvulsant drugs, this evaluation was not carried on new kind of magnesium supplement, magnesium oxide nanoparticles (nMgO. According to the interaction between magnesium and convulsion, this study was designed to evaluate the effect of nMgO on strychnine-induced convulsive model in compared to its conventional in diabetic and normal mice. Methods: Healthy male albino mice were divided to 10 groups. Diabete mellitus was induced by streptozocin in 5 groups. Conventional and nanoparticle MgO (5&10mg/kg in presence and absence diabetes injected to mice, then strychnine injected and onset of convulsions and time of death were measured after strychnine administration. Results: Convulsive parameters did not change in normal and diabetic mice. cMgO pretreatment did not have anticonvulsant effect in strychnine-induced convulsion in normal and diabetic mice. But nMgO significantly changed convulsion onset and death time after strychnine administration in normal and diabetic status. Discussion: According to our results It seems that nMgO may be important in prevention or treatment of epilepsy and has more efficacy than its conventional form to showing anticonvulsive effect that probably is related to the physicochemical properties of nMgO, specially in diabetic subjects, a point that need to further investigation.

Effect of heat treatment on corrosion behavior of low pressure sand cast Mg-10Gd-3Y-0.5Zr alloys

Directory of Open Access Journals (Sweden)

Qian-qian Wu

2016-07-01

Full Text Available The corrosion behaviors of low-pressure sand cast Mg-10Gd-3Y-0.5Zr (wt.% alloys in as-cast, solution treated (T4 and aged (T6 conditions were studied by means of immersion test and electrochemical measurements in 5wt.% NaCl solution saturated with Mg(OH2. It was observed that the corrosion rate in the T4 condition was lower than that of the as-cast and T6 conditions by both sand casting and permanent mold casting with the same order of as-cast>T6>T4; while the corrosion resistance of the permanent mold casting is superior to the sand casting. The morphologies of the corrosion products are similar porous structures consisting of tiny erect flakes perpendicular to the corroded surface of the alloy, irrespective of the heat treatment conditions. Especially, the corrosion film in T4 condition is more compact than that in the other two conditions. In addition, the severer corrosion happening to the as-cast condition is correlated with the galvanic corrosion between the matrix and the eutectic compounds; while improved corrosion resistance for the T4 and T6 conditions is ascribed to the dissolution of the secondary eutectic compounds. The measured corrosion current densities of Mg-10Gd-3Y-0.5Zr alloys in as-cast, T4, and T6 conditions are 36 μA·cm-2, 10 μA·cm-2, and 33 μA·cm-2, respectively. The proposed equivalent circuit [Rs(CPE1(Rt(RfCPE2] by Zview software matches well with the tested electrochemical impedance spectra (EIS data.

Mg-MOF-74/MgF₂ Composite Coating for Improving the Properties of Magnesium Alloy Implants: Hydrophilicity and Corrosion Resistance.

Science.gov (United States)

Liu, Wei; Yan, Zhijie; Ma, Xiaolu; Geng, Tie; Wu, Haihong; Li, Zhongyue

2018-03-07

Surface modification on Mg alloys is highly promising for their application in the field of bone repair. In this study, a new metal-organic framework/MgF₂ (Mg-MOF-74/MgF₂) composite coating was prepared on the surface of AZ31B Mg alloy via pre-treatment of hydrofluoric acid and in situ hydrothermal synthesis methods. The surface topography of the composite coating is compact and homogeneous, and Mg-MOF-74 has good crystallinity. The corrosion resistance of this composite coating was investigated through Tafel polarization test and immersion test in simulated body fluid at 37 °C. It was found that Mg-MOF-74/MgF₂ composite coating significantly slowed down the corrosion rate of Mg alloy. Additionally, Mg-MOF-74/MgF₂ composite coating expresses super-hydrophilicity with the water contact angle of nearly 0°. In conclusion, on the basis of MgF₂ anticorrosive coating, the introduction of Mg-MOF-74 further improves the biological property of Mg alloys. At last, we propose that the hydrophilicity of the composite coating is mainly owing to the large number of hydroxyl groups, the high specific surface area of Mg-MOF-74, and the rough coating produced by Mg-MOF-74 particles. Hence, Mg-MOF-74 has a great advantage in enhancing the hydrophilicity of Mg alloy surface.

Superconducting properties of in situ powder-in-tube-processed MgB2 tapes fabricated with sub-micrometre Mg powder prepared by an arc-plasma method

International Nuclear Information System (INIS)

Yamada, H; Uchiyama, N; Matsumoto, A; Kitaguchi, H; Kumakura, H

2007-01-01

We fabricated in situ powder-in-tube-processed MgB 2 /Fe tapes using sub-micrometre Mg powder prepared by applying an arc-plasma method. We found that the use of this sub-micrometre Mg powder was very effective in increasing the J c values. The transport J c value of 10 mol% SiC-added tapes fabricated with this sub-micrometre Mg powder reached 275 A mm -2 at 4.2 K and 10 T. This value was about six times that of 5 mol% SiC-added tapes fabricated with commercial Mg powder. Microstructure analyses suggest that this J c enhancement is primarily due to the smaller MgB 2 grain size

Hydroxyapatite and zirconia composites: Effect of MgO and MgF2 on the stability of phases and sinterability

International Nuclear Information System (INIS)

Evis, Zafer; Usta, Metin; Kutbay, Isil

2008-01-01

Composites of hydroxyapatite with cubic zirconia with MgO or MgF 2 were pressureless sintered at temperatures from 1000 to 1300 deg. C. The reactions and transformations of phases were monitored with X-ray diffraction. For the hydroxyapatite and zirconia composites with MgO, calcium diffused from hydroxyapatite into the zirconia, and hydroxyapatite decomposed to tri-calcium phosphate at sintering temperatures higher than 1000 deg. C. Above about 1200 deg. C, CaZrO 3 was formed. Composites containing the MgF 2 decomposed slower than the composites with MgO which was verified by the changes in the lattice volume of the hydroxyapatite left in the composites. Fluorine ions in MgF 2 diffused into hydroxyapatite which resulted in thermal stability at high sintering temperatures. Composites with MgF 2 had higher hardness than those with MgO. The lowest porosity was found in a composite initially containing 10 wt% cubic zirconia and 5 wt% MgF 2

Stress corrosion cracking and corrosion fatigue characterisation of MgZn1Ca0.3 (ZX10) in a simulated physiological environment.

Science.gov (United States)

Jafari, Sajjad; Raman, R K Singh; Davies, Chris H J; Hofstetter, Joelle; Uggowitzer, Peter J; Löffler, Jörg F

2017-01-01

Magnesium (Mg) alloys have attracted great attention as potential materials for biodegradable implants. It is essential that an implant material possesses adequate resistance to cracking/fracture under the simultaneous actions of corrosion and mechanical stresses, i.e., stress corrosion cracking (SCC) and/or corrosion fatigue (CF). This study investigates the deformation behaviour of a newly developed high-strength low-alloy Mg alloy, MgZn1Ca0.3 (ZX10), processed at two different extrusion temperatures of 325 and 400°C (named E325 and E400, respectively), under slow strain tensile and cyclic tension-compression loadings in air and modified simulated body fluid (m-SBF). Extrusion resulted in a bimodal grain size distribution with recrystallised grain sizes of 1.2 μm ± 0.8 μm and 7 ± 5 μm for E325 and E400, respectively. E325 possessed superior tensile and fatigue properties to E400 when tested in air. This is mainly attributed to a grain-boundary strengthening mechanism. However, both E325 and E400 were found to be susceptible to SCC at a strain rate of 3.1×10 -7 s -1 in m-SBF. Moreover, both E325 and E400 showed similar fatigue strength when tested in m-SBF. This is explained on the basis of crack initiation from localised corrosion following tests in m-SBF. Crown Copyright © 2016. Published by Elsevier Ltd. All rights reserved.

Is Co Q10 really valuable in shielding statin induced myopathy-an exploration

International Nuclear Information System (INIS)

Noor, M.; Waheed, A.; Muhammad, I; Bakhtiar, S.

2016-01-01

Objective: This study was designed to scrutinize the shielding effects of Co enzyme Q10 (Co Q10) supplementation in statin associated muscular adverse effects in rabbits. Study Design: Randomized controlled trial. Place and Duration of Study: Pharmacology dept Army Medical College Rawalpindi from Jan 2012 to Jun 2012. Material and Methods: Twenty two healthy rabbits were taken and divided into four equal groups randomly with six in each batch. The two groups (G1 and G2) were given toxic doses of simvastatin (60mg/kg/day) with and without Co Q10 (5mg/kg/day) orally for 14 days and rest of two groups (G3 and G4) were kept on therapeutic doses (1mg/kg/day) of simvastatin with and without Co Q10 (5mg/kg/day) orally for 90 days. Blood samples were drawn and serum creatinine kinase (CK) and lactate dehydrogenase (LDH) were assessed before and after the drug therapy. Histopathological examination was done to observe the inflammatory changes under light microscope. The results were analyzed by applying paired 't' test, independent 't' test and ANOVA test for biochemical markers and 'Chi-Square test' for histopathological findings. The p-value < 0.05 was considered significant. Results: The biochemical markers went up sharply (G1. CK=28899.5 +- 874.09 IU/L and LDH = 4694.33 +- 352 IU/L) and (G2. CK = 29191.33 +- 3019.79 IU/L and LDH = 4334.83 +- 143.44 IU/L) as compared to baseline values. They were given toxic doses of simvastatin with and without Co Q10. Histopathological examination of muscular tissue also revealed gross inflammatory changes in these groups. However histopathological examination of groups who were given therapeutic doses of simvastatin with and without Co Q10 for 90 days showed mild to moderate inflammatory changes but serum CK and LDH remained in the normal ranges in these groups. Conclusion: Our results suggest that Co Q10 supplementation could not produce any beneficial effects on the statin induced muscular adverse

Renormalization group running of fermion observables in an extended non-supersymmetric SO(10) model

Energy Technology Data Exchange (ETDEWEB)

Meloni, Davide [Dipartimento di Matematica e Fisica, Università di Roma Tre,Via della Vasca Navale 84, 00146 Rome (Italy); Ohlsson, Tommy; Riad, Stella [Department of Physics, School of Engineering Sciences,KTH Royal Institute of Technology - AlbaNova University Center,Roslagstullsbacken 21, 106 91 Stockholm (Sweden)

2017-03-08

We investigate the renormalization group evolution of fermion masses, mixings and quartic scalar Higgs self-couplings in an extended non-supersymmetric SO(10) model, where the Higgs sector contains the 10{sub H}, 120{sub H}, and 126{sub H} representations. The group SO(10) is spontaneously broken at the GUT scale to the Pati-Salam group and subsequently to the Standard Model (SM) at an intermediate scale M{sub I}. We explicitly take into account the effects of the change of gauge groups in the evolution. In particular, we derive the renormalization group equations for the different Yukawa couplings. We find that the computed physical fermion observables can be successfully matched to the experimental measured values at the electroweak scale. Using the same Yukawa couplings at the GUT scale, the measured values of the fermion observables cannot be reproduced with a SM-like evolution, leading to differences in the numerical values up to around 80%. Furthermore, a similar evolution can be performed for a minimal SO(10) model, where the Higgs sector consists of the 10{sub H} and 126{sub H} representations only, showing an equally good potential to describe the low-energy fermion observables. Finally, for both the extended and the minimal SO(10) models, we present predictions for the three Dirac and Majorana CP-violating phases as well as three effective neutrino mass parameters.

Prevalence of gastroduodenal ulcers/erosions in patients taking low-dose aspirin with either 15 mg/day of lansoprazole or 40 mg/day of famotidine: the OITA-GF study 2.

Science.gov (United States)

Tamura, Akira; Murakami, Kazunari; Kadota, Junichi

2013-03-26

The preventive effects of histamine 2 receptor antagonists vs. proton pump inhibitors on low-dose aspirin (LDA)-related gastroduodenal mucosal injury have not been fully investigated. We conducted a cross-sectional study to compare the prevalence of gastroduodenal ulcers or erosions in patients taking LDA with either 40 mg/day of famotidine or 15 mg/day of lansoprazole for at least three months. Of 84 eligible patients, two taking 40 mg/day of famotidine and four taking 15 mg/day of lansoprazole refused to undergo upper gastrointestinal endoscopy. Ultimately, we performed upper gastrointestinal endoscopy in 78 patients taking either 40 mg/day of famotidine (group F, n = 31) or 15 mg/day of lansoprazole (group L, n = 47). The prevalence of gastroduodenal ulcers or erosions and the magnitude of gastric mucosal injury evaluated using modified Lanza scores were compared between the two groups. No patients in either group had gastroduodenal ulcers. Gastroduodenal erosions were more prevalent in group F than in group L (48.4% vs. 17.0%, p = 0.005). The modified Lanza scores (mean ± SD) were significantly higher in group F than in group L (0.9 ± 1.3 vs. 0.3 ± 0.7, p = 0.007). A multivariate logistic regression analysis showed that the use of lansoprazole was negatively associated with gastroduodenal erosions. This study suggests that 15 mg/day of lansoprazole may be more effective in preventing the development of LDA-related gastroduodenal erosions than 40 mg/day of famotidine. The preventive effects of these two regimens on the development of LDA-related gastroduodenal ulcers require further investigation.

Thermal, Spectral and Laser Properties of Er3+:Yb3+:GdMgB₅O10: A New Crystal for 1.5 μm Lasers.

Science.gov (United States)

Huang, Yisheng; Yuan, Feifei; Sun, Shijia; Lin, Zhoubin; Zhang, Lizhen

2017-12-25

A novel laser crystal of Er 3+ :Yb 3+ :GdMgB₅O 10 with dimension of 26 × 16 × 12 mm³ was grown successfully from K₂Mo₃O 10 flux by the top seeded solution growth method. The thermal diffusivity and specific heat capacity were measured to calculate the thermal conductivity of the crystal. The absorption and fluorescence properties of the crystal at room temperature were investigated in detail. The Judd-Ofelt method was used to analyze the polarized absorption spectra. The emission cross-section of the ⁴I 13/2 →⁴I 15/2 transition was calculated by the Füchtbauer-Ladenburg formula and the relevant gain cross-sections were estimated. Continuous-wave laser output of 140 mW at 1569 nm with the slope efficiency of 17.8% was demonstrated in a plano-concave resonator. The results reveal that Er 3+ :Yb 3+ :GdMgB₅O 10 crystal is a promising material for 1.5 μm lasers.

Randomised, double-blind, placebo-controlled studies on flurbiprofen 8.75 mg lozenges in patients with/without group A or C streptococcal throat infection, with an assessment of clinicians' prediction of 'strep throat'.

Science.gov (United States)

Shephard, A; Smith, G; Aspley, S; Schachtel, B P

2015-01-01

Diagnosing group A streptococcus (Strep A) throat infection by clinical examination is difficult, and misdiagnosis may lead to inappropriate antibiotic use. Most patients with sore throat seek symptom relief rather than antibiotics, therefore, therapies that relieve symptoms should be recommended to patients. We report two clinical trials on the efficacy and safety of flurbiprofen 8.75 mg lozenge in patients with and without streptococcal sore throat. The studies enrolled adults with moderate-to-severe throat symptoms (sore throat pain, difficulty swallowing and swollen throat) and a diagnosis of pharyngitis. The practitioner assessed the likelihood of Strep A infection based on historical and clinical findings. Patients were randomised to flurbiprofen 8.75 mg or placebo lozenges under double-blind conditions and reported the three throat symptoms at baseline and at regular intervals over 24 h. A total of 402 patients received study medication (n = 203 flurbiprofen, n = 199 placebo). Throat culture identified Strep A in 10.0% of patients and group C streptococcus (Strep C) in a further 14.0%. The practitioners' assessments correctly diagnosed Strep A in 11/40 cases (sensitivity 27.5%, and specificity 79.7%). A single flurbiprofen lozenge provided significantly greater relief than placebo for all three throat symptoms, lasting 3-4 h for patients with and without Strep A/C. Multiple doses of flurbiprofen lozenges over 24 h also led to symptom relief, although not statistically significant in the Strep A/C group. There were no serious adverse events. The results highlight the challenge of identifying Strep A based on clinical features. With the growing problem of antibiotic resistance, non-antibiotic treatments should be considered. As demonstrated here, flurbiprofen 8.75 mg lozenges are an effective therapeutic option, providing immediate and long-lasting symptom relief in patients with and without Strep A/C infection. © 2014 John Wiley & Sons Ltd.

Mineralogy of the fraction and age estimation rubidium - strontium of the Bambui Group, MG, Brazil

International Nuclear Information System (INIS)

Bonhomme, M.G.

1976-01-01

A study of the illite crystallinity of sediments of the Upper Precambrian Bambui Group, MG, has been done to determine the zones without metamorphism, the only ones able to give the age of the sedimentation. Only the region of Januaria escaped from any sensible thermo-tectonic event. The Bambui sediments contain well crystallized vermiculite probably formed during the anchimetamorphism. The rubidium-strontium age obtained in Januaria (619 + - 17 m.y.) corresponds in fact to the main phase of the Brazilian orogenic cycle. The late isotopic homogeneization was caused by a strong late diagenesis. The anchimetamorphic phosphateous sediments in Cedro do Abate show that the ferro-magnesian illite is a more easely open system than aluminous illite, and in this case dates the later event of the Brazilian cycle at 445 + - 25 m.y. The age of 600 m.y. for the metamorphism is a younger limit for the real age of the Bambui, the late Precambrian age of which is confirmed

Influence of Heat Treatment on Biocorrosion and Hemocompatibility of Biodegradable Mg-35Zn-3Ca Alloy

Directory of Open Access Journals (Sweden)

Jeong-Hui Ji

2015-01-01

Full Text Available Mg-35Zn-3Ca (wt.% alloy containing nontoxic and biocompatible Zn and Ca as alloying elements was prepared and subjected to heat treatment and artificial aging for different duration of time to reduce its rate of degradation. Solution heat treatment was performed at 310°C while artificial aging was performed at 170°C for 0, 2.5, 5.0, 7.5, and 10.0 h and they were designated as AT0, AT1, AT2, AT3, and AT4, respectively. The finest and most homogenous reticulum was observed on the surface of the AT2 group. The result of immersion test in Hank’s balanced salt solution (HBSS showed that the corrosion rate of the AT2 group was 2.32 mg/(cm2 day, which was significantly lower as compared to other groups P<0.05. The hemolysis value was ≤5% in all groups, indicating no toxicity during short-term blood reaction.

Monolithic translucent BaMgAl10O17:Eu2+ phosphors for laser-driven solid state lighting

Directory of Open Access Journals (Sweden)

Clayton Cozzan

2016-10-01

Full Text Available With high power light emitting diodes and laser diodes being explored for white light generation and visible light communication, thermally robust encapsulation schemes for color-converting inorganic phosphors are essential. In the current work, the canonical blue-emitting phosphor, high purity Eu-doped BaMgAl10O17, has been prepared using microwave-assisted heating (25 min and densified into translucent ceramic phosphor monoliths using spark plasma sintering (30 min. The resulting translucent ceramic monoliths convert UV laser light to blue light with the same efficiency as the starting powder and provide superior thermal management in comparison with silicone encapsulation.

Continuum simulation of heat transfer and solidification behavior of AlSi10Mg in Direct Metal Laser Sintering Process

Science.gov (United States)

Ojha, Akash; Samantaray, Mihir; Nath Thatoi, Dhirendra; Sahoo, Seshadev

2018-03-01

Direct Metal Laser Sintering (DMLS) process is a laser based additive manufacturing process, which built complex structures from powder materials. Using high intensity laser beam, the process melts and fuse the powder particles makes dense structures. In this process, the laser beam in terms of heat flux strikes the powder bed and instantaneously melts and joins the powder particles. The partial solidification and temperature distribution on the powder bed endows a high cooling rate and rapid solidification which affects the microstructure of the build part. During the interaction of the laser beam with the powder bed, multiple modes of heat transfer takes place in this process, that make the process very complex. In the present research, a comprehensive heat transfer and solidification model of AlSi10Mg in direct metal laser sintering process has been developed on ANSYS 17.1.0 platform. The model helps to understand the flow phenomena, temperature distribution and densification mechanism on the powder bed. The numerical model takes into account the flow, heat transfer and solidification phenomena. Simulations were carried out for sintering of AlSi10Mg powders in the powder bed having dimension 3 mm × 1 mm × 0.08 mm. The solidification phenomena are incorporated by using enthalpy-porosity approach. The simulation results give the fundamental understanding of the densification of powder particles in DMLS process.

10 CFR 110.30 - Members of the Nuclear Suppliers Group.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Members of the Nuclear Suppliers Group. 110.30 Section 110.30 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) EXPORT AND IMPORT OF NUCLEAR EQUIPMENT AND... Italy Japan Latvia Luxembourg Netherlands New Zealand Norway Poland Portugal Republic of Korea Romania...

8x8 and 10x10 Hyperspace Representations of SU(3) and 10-fold Point-Symmetry Group of Quasicrystals

Science.gov (United States)

Animalu, Alexander

2012-02-01

In order to further elucidate the unexpected 10-fold point-symmetry group structure of quasi-crystals for which the 2011 Nobel Prize in chemistry was awarded to Daniel Shechtman, we explore a correspondence principle between the number of (projective) geometric elements (points[vertices] + lines[edges] + planes[faces]) of primitive cells of periodic or quasi-periodic arrangement of hard or deformable spheres in 3-dimensional space of crystallography and elements of quantum field theory of particle physics [points ( particles, lines ( particles, planes ( currents] and hence construct 8x8 =64 = 28+36 = 26 + 38, and 10x10 =100= 64 + 36 = 74 + 26 hyperspace representations of the SU(3) symmetry of elementary particle physics and quasicrystals of condensed matter (solid state) physics respectively, As a result, we predict the Cabibbo-like angles in leptonic decay of hadrons in elementary-particle physics and the observed 10-fold symmetric diffraction pattern of quasi-crystals.

WIPP Magnesium Oxide (MgO) - Planned Change Request

Science.gov (United States)

On April 10, 2006, the DOE submitted a planned change request pertaining to the amount of MgO emplaced in the WIPP repository. MgO is an engineered barrier that DOE included as part of the original WIPP Certification Decision.

Comparing the Electrochemical Performance of LiFePO4/C Modified by Mg Doping and MgO Coating

Directory of Open Access Journals (Sweden)

Jianjun Song

2013-01-01

Full Text Available Supervalent cation doping and metal oxide coating are the most efficacious and popular methods to optimize the property of LiFePO4 lithium battery material. Mg-doped and MgO-coated LiFePO4/C were synthesized to analyze their individual influence on the electrochemical performance of active material. The specific capacity and rate capability of LiFePO4/C are improved by both MgO coating and Mg doping, especially the Mg-doped sample—Li0.985Mg0.015FePO4/C, whose discharge capacity is up to 163 mAh g−1, 145.5 mAh g−1, 128.3 mAh g−1, and 103.7 mAh g−1 at 1 C, 2 C, 5 C, and 10 C, respectively. The cyclic life of electrode is obviously increased by MgO surface modification, and the discharge capacity retention rate of sample LiFePO4/C-MgO2.5 is up to 104.2% after 100 cycles. Comparing samples modified by these two methods, Mg doping is more prominent on prompting the capacity and rate capability of LiFePO4, while MgO coating is superior in terms of improving cyclic performance.

Roymillerite, Pb24Mg9(Si9AlO28)(SiO4)(BO3)(CO3)10(OH)14O4, a new mineral: mineralogical characterization and crystal chemistry

Science.gov (United States)

Chukanov, Nikita V.; Jonsson, Erik; Aksenov, Sergey M.; Britvin, Sergey N.; Rastsvetaeva, Ramiza K.; Belakovskiy, Dmitriy I.; Van, Konstantin V.

2017-11-01

The new mineral roymillerite Pb24Mg9(Si9AlO28)(SiO4)(BO3)(CO3)10(OH)14O4, related to britvinite and molybdophyllite, was discovered in a Pb-rich assemblage from the Kombat Mine, Grootfontein district, Otjozondjupa region, Namibia, which includes also jacobsite, cerussite, hausmannite, sahlinite, rhodochrosite, barite, grootfonteinite, Mn-Fe oxides, and melanotekite. Roymillerite forms platy single-crystal grains up to 1.5 mm across and up to 0.3 mm thick. The new mineral is transparent, colorless to light pink, with a strong vitreous lustre. Cleavage is perfect on (001). Density calculated using the empirical formula is equal to 5.973 g/cm3. Roymillerite is optically biaxial, negative, α = 1.86(1), β ≈ γ = 1.94(1), 2 V (meas.) = 5(5)°. The IR spectrum shows the presence of britvinite-type tetrahedral sheets, {CO}3^{2 - }, {BO}3^{3 - }, and OH- groups. The chemical composition is (wt%; electron microprobe, H2O and CO2 determined by gas chromatography, the content of B2O3 derived from structural data): MgO 4.93, MnO 1.24, FeO 0.95, PbO 75.38, B2O3 0.50, Al2O3 0.74, CO2 5.83, SiO2 7.90, H2O 1.8, total 99.27. The empirical formula based on 83 O atoms pfu (i.e. Z = 1) is Pb24.12Mg8.74Mn1.25Fe0.94B1.03Al1.04C9.46Si9.39H14.27O83. The crystal structure was determined using single-crystal X-ray diffraction data. The new mineral is triclinic, space group P \\bar{1}, with a = 9.315(1), b = 9.316(1), c = 26.463(4) Å, α = 83.295(3)°, β = 83.308(3)°, γ = 60.023(2)°, V = 1971.2(6) Å3. The crystal structure of roymillerite is based built by alternating pyrophyllite-type TOT-modules Mg9(OH)8[(Si,Al)10O28] and I-blocks Pb24(OH)6O4(CO3)10(BO3,SiO4). The strongest lines of the powder X-ray diffraction pattern [ d, Å (I, %) ( hkl)] are: 25.9 (100) (001), 13.1 (11) (002), 3.480 (12) (017, 107, -115, 1-15), 3.378 (14) (126, 216), 3.282 (16) (-2-15, -1-25), 3.185 (12) (-116, 1-16), 2.684 (16) (031, 301, 030, 300, 332, -109, 0-19, 1-18), 2.382 (11) (0.0.-11). Roymillerite is

Superconducting properties of in situ powder-in-tube-processed MgB{sub 2} tapes fabricated with sub-micrometre Mg powder prepared by an arc-plasma method

Energy Technology Data Exchange (ETDEWEB)

Yamada, H [Maglev System Development Division, Central Japan Railway Company, 1545-33, Ooyama, Komaki, Aichi 485-0801 (Japan); Uchiyama, N [Maglev System Development Division, Central Japan Railway Company, 1545-33, Ooyama, Komaki, Aichi 485-0801 (Japan); Matsumoto, A [Superconducting Materials Center, National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Kitaguchi, H [Superconducting Materials Center, National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Kumakura, H [Superconducting Materials Center, National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, Ibaraki 305-0047 (Japan)

2007-01-15

We fabricated in situ powder-in-tube-processed MgB{sub 2}/Fe tapes using sub-micrometre Mg powder prepared by applying an arc-plasma method. We found that the use of this sub-micrometre Mg powder was very effective in increasing the J{sub c} values. The transport J{sub c} value of 10 mol% SiC-added tapes fabricated with this sub-micrometre Mg powder reached 275 A mm{sup -2} at 4.2 K and 10 T. This value was about six times that of 5 mol% SiC-added tapes fabricated with commercial Mg powder. Microstructure analyses suggest that this J{sub c} enhancement is primarily due to the smaller MgB{sub 2} grain size.

Synthesis and characterization of LiF: Mg, Ti for ionizing radiations dosimetry

International Nuclear Information System (INIS)

Lozano R, I. B.

2011-01-01

Among the different thermoluminescence materials (Tl), the LiF:Mg, Ti is the most used for dosimetric purposes, because its equivalence to the human tissue, it has an effective atomic number of 8.14, the best known commercial dosemeter of this kind is the TLD-100. However, because this dosimeter is an imported product, is quite expensive for many research groups and hospitals. The purpose of this work is the optimization of its synthesis, as the dosimetric characterization, so it can replace the imported dosimeters. The synthesis of LiF:Mg, Ti is a careful process, since one of the reagents, the ion fluorine is highly corrosive. In this work the synthesis of the LiF:Mg, Ti was done by the molten substance method, was used LiF of analytical grade and the magnesium (Mg) and titanium (Ti) activators were incorporated in aqueous solution. For to optimize the handle of the material Tl, we elaborated pellets and teflon (Ptfe) was used as agglutinate material, in a 2:3 proportion. First was prepared the LiF, incorporating just Mg as dopant with a concentration of 400 parts per million (ppm). After the Ti with concentrations from 15 to 120 ppm was incorporated keeping fixed the concentration of Mg (400 ppm). The morphological and structural characterization of the Tl material were made by scanning electron microscopy and X-ray diffraction. The optimal concentration of Ti, was determined as a function of the radiation dose sensibility of the Tl material. The material prepared with 60 ppm of the Ti showed a higher sensibility. However, also the rest of the preparations had the requirements recommended by the international agencies to be used in ionizing radiations dosimetry. For the dosimetric characterization were used samples with 400 ppm of Mg, 400 ppm Mg and 30 ppm Ti, 400 ppm Mg and 60 ppm Ti. The LiF:Mg showed its dosimetric peak at 240 C, while the LiF:Mg, Ti (30 ppm and 60 ppm Ti) showed their dosimetric peak at 220 C and 222 C respectively. The study of the Tl

Phase formation in the Ag2O - MgO - MoO3 system and the crystal structure of new double molybdate Ag2Mg2(MoO4)3

International Nuclear Information System (INIS)

Tsyrenova, G.D.; Khajkina, E.G.; Khobrakova, Eh.T.; Solodovnikov, S.F.

2001-01-01

The phase correlations in subsolidus area of the Ag 2 O - MgO - MoO 3 system were studied, the Ag 2 MoO 4 - MgMoO 4 polythermal cross-section was investigated and its T-x diagram was constructed. X-ray diffraction and thermal analytic researches were conducted. The formation of the new double Ag 2 Mg 2 (MoO 4 ) 3 molybdates relating to the structural group Na 2 Mg 5 (MoO 4 ) 6 was established, and its structure (a=6.978(1), b=8.715(2), c=10.294(2) A, α=107.56(3) Deg, β=105.11(3) Deg, γ=103.68(3) Deg, Z=2, sp. gr. P 1-bar, R=0.038) was determined. The mixed carcass from the twin MgO 6 -octahedrons and MoO 4 -tetrahedrons, in which blankness the Ag atoms are arranged, stand out in the structure.The character of disordering in the part of Ag + is analogous to previously found one in the Ag 2 Zn 2 (MoO 4 ) 3 structure. The possible limits in the fields of homogeneity of silver-magnesium molybdate and its analogs, as well as the differences their structure from the structure of isotopic sodium-containing phases, are discussed [ru

Corrosion and Discharge Behaviors of Mg-Al-Zn and Mg-Al-Zn-In Alloys as Anode Materials

Directory of Open Access Journals (Sweden)

Jiarun Li

2016-03-01

Full Text Available The Mg-6%Al-3%Zn and Mg-6%Al-3%Zn-(1%, 1.5%, 2%In alloys were prepared by melting and casting. Their microstructures were investigated via metallographic and energy-dispersive X-ray spectroscopy (EDS analysis. Moreover, hydrogen evolution and electrochemical tests were carried out in 3.5 wt% NaCl solution aiming at identifying their corrosion mechanisms and discharge behaviors. The results suggested that indium exerts an improvement on both the corrosion rate and the discharge activity of Mg-Al-Zn alloy via the effects of grain refining, β-Mg17Al12 precipitation, dissolving-reprecipitation, and self-peeling. The Mg-6%Al-3%Zn-1.5%In alloy with the highest corrosion rate at free corrosion potential did not perform desirable discharge activity indicating that the barrier effect caused by the β-Mg17Al12 phase would have been enhanced under the conditions of anodic polarization. The Mg-6%Al-3%Zn-1.0%In alloy with a relative low corrosion rate and a high discharge activity is a promising anode material for both cathodic protection and chemical power source applications.

Stability of rapidly quenched and hydrogenated Mg-Ni-Y and Mg-Cu-Y alloys in extreme alkaline medium

International Nuclear Information System (INIS)

Gebert, A.; Khorkounov, B.; Wolff, U.; Mickel, Ch.; Uhlemann, M.; Schultz, L.

2006-01-01

Amorphous-nanocrystalline Mg 50 Ni 30 Y 20 and Mg 63 Ni 30 Y 7 and amorphous Mg 65 Cu 25 Y 10 alloys were produced by melt-spinning and characterized regarding their microstructure and thermal behaviour using XRD, TEM and DSC. Their electrochemical behaviour in the as-quenched state and after hydrogen charging at -25 mA/cm 2 for up to 20 h was studied in electrolytes with pH 5-7 and 13, but mainly in a battery electrolyte: 6 M KOH with pH 14.8 by means of anodic and cathodic polarization measurements. In the as-quenched state, the highest alloys stability was observed at pH 13. At pH 14.8, gradual oxidation and dissolution of copper or nickel governs the anodic behaviour before a passive state is attained. The dissolution of nickel is much more inhibited than that of copper due to its lower tendency to form soluble oxidized ions and to a stabilizing effect of higher fractions of yttrium in the alloy on the passivation. By galvanostatic charging, the Mg 65 Cu 25 Y 10 alloy shows the highest hydrogen absorption capacity followed by Mg 50 Ni 30 Y 20 and Mg 63 Ni 30 Y 7 . During the charging process, the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel- or copper-rich species, causing preferential oxidation and dissolution during subsequent exposure under free corrosion and anodic conditions. Mg-Ni-Y alloys demonstrate a higher stability during this treatment in extreme alkaline medium. The reasons for this and consequences regarding the use as electrode materials are discussed in detail

Investigation of Performance and Residual Stress Generation of AlSi10Mg Processed by Selective Laser Melting

Directory of Open Access Journals (Sweden)

Lianfeng Wang

2018-01-01

Full Text Available During the selective laser melting (SLM process, the scanned layers are subjected to rapid thermal cycles. By working on the mechanical properties, residual stress, and microstructure, the high-temperature gradients can have significant effect on the proper functioning and the structural integrity of built parts. This work presents a comprehensive study on the scanning path type and preheating temperature for AlSi10Mg alloy during SLM. According to the results, SLM AlSi10Mg parts fabricated in chessboard scanning strategy have higher mechanical properties or at least comparable to the parts fabricated in uniformity scanning strategy. In the SLM processing, the residual stress in different parts of the specimen varies with temperature gradient, and the residual stress at the edge of the specimen is obviously larger than that at the center. Under the chessboard scanning and preheating temperature 160°C, the residual stress in each direction of the specimens reaches the minimum. Under different forming processes, the morphology of the microstructure is obviously different. With the increase of preheating temperature, the molten pool in the side surface is obviously elongated and highly unevenly distributed. From the coupling relationship between the residual stress and microstructure, it can be found that the microstructure of top surface is affected by residual stresses σx and σy. But the side surface is mainly governed by residual stress σy; moreover, the greater the residual stress, the more obvious the grain tilt. In the XY and XZ surfaces, the scanning strategy has little influence on the tilt angle of the grain. But, the tilt angle and morphology of the microstructure are obviously affected by the preheating temperature. The results show that the residual stresses can effectively change the properties of the materials under the combined influence of scanning strategy and preheating temperature.

Comparative trial of two intravenous doses of granisetron (1 versus 3 mg) in the prevention of chemotherapy-induced acute emesis: a double-blind, randomized, non-inferiority trial.

Science.gov (United States)

Tsuji, Daiki; Kim, Yong-Il; Taku, Keisei; Nakagaki, Shigeru; Ikematsu, Yoshito; Tsubota, Hiromi; Maeda, Masato; Hashimoto, Naoya; Kimura, Masayuki; Daimon, Takashi

2012-05-01

A single 3 mg or 40 μg/kg intravenous dose of granisetron combined with dexamethasone is routinely used in several countries, although the antiemetic guidelines have recommended granisetron at the dose of 1 mg or 10 μg/kg. A randomized, multicenter trial was conducted to determine the optimal intravenous granisetron dose, 1 or 3 mg, in cancer patients receiving emetogenic chemotherapy. We enrolled 365 patients and randomly assigned them to receive intravenous granisetron 3 mg (3-mg group) or 1 mg (1-mg group), combined with dexamethasone at an adequate dose fixed as per the emetic risk category. The primary end point was the proportion of patients with a complete response during the first 24 h after chemotherapy. The study demonstrated that 1 mg of granisetron was not inferior in effect to 3 mg. For the primary end point, 359 patients were evaluable according to the modified intention-to-treat (ITT) analysis. Complete protection was achieved in the modified ITT population, 90.6% and 88.8% for the 3- and 1-mg groups, respectively (p granisetron is not inferior to 3 mg when both doses are combined with dexamethasone. Therefore, 1-mg dose of intravenous granisetron should be the recommended prophylactic regimen for the prevention of acute emesis.

PWR Users Group 10 CFR 61 Waste Form Requirements Compliance Test Program

International Nuclear Information System (INIS)

Rosenlof, R.C.

1985-01-01

In January of 1984, a PWR Users Group was formed to initiate a 10 CFR 61 Waste Form Requirements Compliance Test Program on a shared cost basis. The original Radwaste Solidification Systems sold by ATCOR ENGINEERED SYSTEMS, INC. to the utilities were required to produce a free-standing monolith with no free water. None of the other requirements of 10 CFR 61 had to be met. Current regulations, however, have substantially expanded the scope of the waste form acceptance criteria. These new criteria required that generators of radioactive waste demonstrate the ability to produce waste forms which meet certain chemical and physical requirements. This paper will present the test program used and the results obtained to insure 10 CFR 61 compliance of the three (3) typical waste streams generated by the ATCOR PWR Users Group's plants. The primary objective of the PWR Users Group was not to maximize waste loading within the masonry cement solidification media, but to insure that the users Radwaste Solidification System is capable of producing waste forms which meet the waste form criteria of 10 CFR 61. A description of the laboratory small sample certification program and the actual full scale pilot plant verification approach used is included in this paper. Also included is a discussion of the development of a Process Control Program to ensure the reproducibility of the test results with actual waste

COMBINED SPINAL EPIDURAL ANALGESIA IN LABOUR: COMPARISON OF BUPIVACAINE 1.25 MG WITH FENTANYL AND ROPIVACAINE 2.5 MG WITH FENTANYL INTRATHECAL

Directory of Open Access Journals (Sweden)

Prakash T. S. N

2016-10-01

with ASA I and ASA II in established labour with cervical dilatation less than 5 cm was selected and randomly allocated into two groups using closed envelope method. Informed written consent was taken from all participants. They were divided into 2 groups of 20 each. Group I received intrathecal Inj. Bupivacaine 1.25 mg and Inj. Fentanyl 20 µg. Group II received intrathecal Inj. Ropivacaine 2.5 mg and Inj. Fentanyl 20 µg for combined spinal epidural. IV line was secured with 18G cannula. Patient was preloaded with 500 mL of Hartmann’s solution. Basal vital parameter like pulse rate, blood pressure, respiration, O2 saturation were recorded. The patient was positioned in a sitting position with the help of an assistant. Under aseptic conditions, the back was prepared with 5% povidone-iodine solution, spirit and area was draped. L3-L4 interspace was identified. Skin was infiltrated with 2 mL of 1% Xylocaine. After infiltration of local anaesthetic by using needle through needle technique 18-gauge Tuohy needle, epidural space was identified with loss of resistance to air technique. Then, a 15 mm (27 G long ‘Whitacre’ spinal needle was introduced through the epidural needle and the correct position of the tip in the intrathecal space was confirmed by observation of free flow of CSF. Patients were allocated randomly to receive intrathecal injection of bupivacaine 1.25 mg (0.5% bupivacaine 0.25 mL with fentanyl 20 µg (Group I n=30 or ropivacaine 2.5 mg/0.2% ropivacaine 1.25 mL with fentanyl 20 µg (Group II, n=30 both made up to total volume of 2 mL with saline. Injection of intrathecal drug was completed in 10 secs., then 20G epidural catheter was threaded through the epidural needle into the epidural space in cephalad direction. The epidural needle was slowly pulled out without disturbing the catheter. About 3 to 5 cm of catheter was left in epidural space. The catheter was well secured with plaster. Patients vitals was recorded every 5, 10, 15, 30, 45, 60, 75, 90

Prevalence of gastroduodenal ulcers/erosions in patients taking low-dose aspirin with either 15 mg/day of lansoprazole or 40 mg/day of famotidine: The OITA-GF study 2

Science.gov (United States)

2013-01-01

Background The preventive effects of histamine 2 receptor antagonists vs. proton pump inhibitors on low-dose aspirin (LDA)-related gastroduodenal mucosal injury have not been fully investigated. We conducted a cross-sectional study to compare the prevalence of gastroduodenal ulcers or erosions in patients taking LDA with either 40 mg/day of famotidine or 15 mg/day of lansoprazole for at least three months. Methods Of 84 eligible patients, two taking 40 mg/day of famotidine and four taking 15 mg/day of lansoprazole refused to undergo upper gastrointestinal endoscopy. Ultimately, we performed upper gastrointestinal endoscopy in 78 patients taking either 40 mg/day of famotidine (group F, n = 31) or 15 mg/day of lansoprazole (group L, n = 47). The prevalence of gastroduodenal ulcers or erosions and the magnitude of gastric mucosal injury evaluated using modified Lanza scores were compared between the two groups. Results No patients in either group had gastroduodenal ulcers. Gastroduodenal erosions were more prevalent in group F than in group L (48.4% vs. 17.0%, p = 0.005). The modified Lanza scores (mean ± SD) were significantly higher in group F than in group L (0.9 ± 1.3 vs. 0.3 ± 0.7, p = 0.007). A multivariate logistic regression analysis showed that the use of lansoprazole was negatively associated with gastroduodenal erosions. Conclusions This study suggests that 15 mg/day of lansoprazole may be more effective in preventing the development of LDA-related gastroduodenal erosions than 40 mg/day of famotidine. The preventive effects of these two regimens on the development of LDA-related gastroduodenal ulcers require further investigation. PMID:23531145

Evaluation of 500- and 1,000-mg doses of ciprofloxacin for the treatment of chancroid.

Science.gov (United States)

Bodhidatta, L; Taylor, D N; Chitwarakorn, A; Kuvanont, K; Echeverria, P

1988-01-01

A randomized, double-blind study was performed comparing ciprofloxacin in a 500-mg single dose with 1,000 mg (500-mg doses given 12 h apart) for the treatment of chancroid in Thailand. Haemophilus ducreyi was isolated from 87 (48%) of 180 men with a clinical diagnosis of chancroid. For men with ulcers that were culture positive for H. ducreyi, rates of cure were 100% in the 500-mg group and 98% in the 1,000-mg group. For men with ulcers that were culture negative for H. ducreyi, rates of cure were 93% in the 500-mg group and 96% in the 1,000-mg group. The MIC of ciprofloxacin for 50% of isolates among 85 isolates of H. ducreyi was 0.007 micrograms/ml (range, 0.002 to 0.03 micrograms/ml). No significant adverse effects were detected in either group. These data indicate that both of these treatment regimens are equally effective therapies for chancroid in Thailand. PMID:3293526

LOW Mg/Si PLANETARY HOST STARS AND THEIR Mg-DEPLETED TERRESTRIAL PLANETS

Energy Technology Data Exchange (ETDEWEB)

Carter-Bond, Jade C.; O' Brien, David P. [Planetary Science Institute, 1700 E. Fort Lowell, Tucson, AZ 85719 (United States); Delgado Mena, Elisa; Israelian, Garik; Gonzalez Hernandez, Jonay I. [Instituto de Astrofisica de Canarias, 38200 La Laguna, Tenerife (Spain); Santos, Nuno C., E-mail: j.bond@unsw.edu.au [Centro de Astrofisica, Universidade do Porto, Rua das Estrelas, 4150-762 Porto (Portugal)

2012-03-15

Simulations have shown that a diverse range of extrasolar terrestrial planet bulk compositions are likely to exist based on the observed variations in host star elemental abundances. Based on recent studies, it is expected that a significant proportion of host stars may have Mg/Si ratios below 1. Here we examine this previously neglected group of systems. Planets simulated as forming within these systems are found to be Mg-depleted (compared to Earth), consisting of silicate species such as pyroxene and various feldspars. Planetary carbon abundances also vary in accordance with the host star C/O ratio. The predicted abundances are in keeping with observations of polluted white dwarfs, lending validity to this approach. Further studies are required to determine the full planetary impacts of the bulk compositions predicted here.

Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder

International Nuclear Information System (INIS)

Thijs, Lore; Kempen, Karolien; Kruth, Jean-Pierre; Van Humbeeck, Jan

2013-01-01

Graphical abstract: -- Abstract: This study shows that AlSi10Mg parts with an extremely fine microstructure and a controllable texture can be obtained through selective laser melting (SLM). Selective laser melting creates complex functional products by selectively melting powder particles of a powder bed layer after layer using a high-energy laser beam. The high-energy density applied to the material and the additive character of the process result in a unique material structure. To investigate this material structure, cube-shaped SLM parts were made using different scanning strategies and investigated by microscopy, X-ray diffraction and electron backscattered diffraction. The experimental results show that the high thermal gradients occurring during SLM lead to a very fine microstructure with submicron-sized cells. Consequently, the AlSi10Mg SLM products have a high hardness of 127 ± 3 Hv0.5 even without the application of a precipitation hardening treatment. Furthermore, due to the unique solidification conditions and the additive character of the process, a morphological and crystallographic texture is present in the SLM parts. Thanks to the knowledge gathered in this paper on how this texture is formed and how it depends on the process parameters, this texture can be controlled. A strong fibrous 〈1 0 0〉 texture can be altered into a weak cube texture along the building and scanning directions when a rotation of 90° of the scanning vectors within or between the layers is applied

Comparison of the Effect of Naftopidil 75 mg and Tamsulosin 0.2 mg on the Bladder Storage Symptom With Benign Prostatic Hyperplasia: Prospective, Multi-institutional Study.

Science.gov (United States)

Kwon, Se Yun; Lee, Kyung Seop; Yoo, Tag Keun; Chung, Jae Il; Lee, Ji Youl; Hong, Jun Hyuk; Seo, Seong Il; Jung, Tae Young; Kwak, Cheol; Kang, Taek Won; Yun, Seok-Joong

2018-01-01

To compare the efficacies of naftopidil and tamsulosin in terms of reducing storage symptoms in patients with benign prostatic hyperplasia. This prospective randomized study was performed at 10 centers. Ninety-four patients that had been taking tamsulosin for more than 8 weeks, but had an Overactive Bladder Symptom Score (OABSS) of greater than 3 points, were initially enrolled. After a 1-week washout period, patients were divided into 2 groups. Forty-five patients were treated with tamsulosin 0.2 mg daily, and 49 patients were treated with naftopidil 75 mg daily for 8 weeks. Total International Prostate Symptoms Score (IPSS), storage symptom scores, nocturia times, OABSS, maximal flow rates (Q max ), and postvoid residual volumes were checked before and after the 8-week treatment period. Mean patient ages in the tamsulosin and naftopidil groups were 64.8 and 66.0 years, respectively. Baseline characteristics were not significantly different. In the tamsulosin group, mean total IPSS decreased from 19.1 to 15.1 after the 8-week treated period (P = .001), and in the naftopidil group, mean total IPSS decreased from 16.9 to 13.1 (P = .001). Mean storage symptom scores were reduced in the tamsulosin and naftopidil groups from 8.0 to 6.6 (P = .002) and from 7.6 to 6.1 (P = .001), respectively. Mean nocturia times in the naftopidil groups decreased significantly from 2.5 to 1.9 (P = .001), and mean OABSSs were reduced from 7.7 to 6.0 (P = .001) and from 7.4 to 6.0 (P = .001), respectively. Total IPSS, storage symptom scores, nocturia times, and OABSS were significantly reduced by naftopidil and tamsulosin. Moreover, the naftopidil group showed better improvements in nocturia than the tamsulosin group. Copyright © 2017 Elsevier Inc. All rights reserved.

Infrared emissions in MgSrAl10O17:Er3+ phosphor co-doped with Yb3+/Ba2+/Ca2+ obtained by solution combustion route

International Nuclear Information System (INIS)

Singh, Vijay; Kumar Rai, Vineet; Venkatramu, V.; Chakradhar, R.P.S.; Hwan Kim, Sang

2013-01-01

An intense infrared emitting MgSrAl 10 O 17 :Er 3+ phosphor co-doped with Yb 3+ , Ba 2+ and Ca 2+ ions have been prepared by a solution combustion method. Phase purity of the derived compounds was confirmed by X-ray diffraction technique. The vibrational properties of MgSrAl 10 O 17 phosphor was studied by Fourier transform infrared spectroscopy. The broad and strong infrared emission of Er 3+ ions at around 1.53 μm was observed upon excitation at 980 nm. Effect of co-doping with the Yb 3+ , Ba 2+ and Ca 2+ ions on the infrared luminescence intensity of Er 3+ ions and the mechanism responsible for the variation in the infrared intensity have been discussed. The results indicate that these materials may be suitable for the optical telecommunication window and wavelength division multiplexing applications. - Highlights: ► The hexagonal phase of MgSrAl 10 O 17 could be obtained by the low temperature combustion method. ► The broad and strong infrared emission of Er 3+ ions at around 1.53 μm was observed. ► Effect of co-doping with the Yb 3+ , Ba 2+ and Ca 2+ ions on the infrared luminescence intensity of Er 3+ were reported.

Biological activity evaluation of magnesium fluoride coated Mg-Zn-Zr alloy in vivo.

Science.gov (United States)

Jiang, Hongfeng; Wang, Jingbo; Chen, Minfang; Liu, Debao

2017-06-01

To explore the biodegradable characteristics and biological properties, which could promote new bone formation, of MgF 2 coated magnesium alloy (Mg-3wt%Zn-0.5wt%Zr) in rabbits. Magnesium alloy with MgF 2 coating was made and the MgF 2 /Mg-Zn-Zr was implanted in the femoral condyle of rabbits. Twelve healthy adult Japanese white rabbits in weight of 2.8-3.2kg were averagely divided into A(Mg-Zn-Zr) group and B(MgF 2 /MgZn-Zr) group. Indexes such as microstructural evolution, SEM scan, X-ray, Micro-CT and mechanical properties were observed and detected at 1th day, 2th, 4th, 8th, 12th, 24th week after implantation. Low-density regions occurred around the cancellous bone, and the regions gradually expanded during the 12weeks after implantation. The implant was gradually absorbed from 12 to 24weeks. The density of surrounding cancellous bone increased compared with the 12th week data. The degradation rate of B group was lower than that of A group (Pmagnesium ions. The biological properties of the coating itself presented good biocompatibility and bioactivity. Copyright © 2017 Elsevier B.V. All rights reserved.

The Age-Precipitations Structure Of Al-Mg-Ge Alloy Aged At 473K

Directory of Open Access Journals (Sweden)

Kawai A.

2015-06-01

Full Text Available The Al-Mg-Ge alloy is one of the age-hardening aluminum alloy after solution heat treatment. It has been proposed that the age-precipitation behavior of Al-Mg-Ge alloy is different from that of Al-Mg-Si alloy according to our previous works about the microstructure on Al-Mg-Ge alloy over-aged at 523K. For example, The hardness of peak aged Al-1.0mass%Mg2Ge alloy is higher than that of Al-1.0mass%Mg2Si alloy. The precipitates in the over-aged samples have been classified as some metastable phases, such as the β’-phase and Type-A precipitates and equilibrium phase of β-Mg2Ge by TEM observation. There a few reports about microstructure on Al-Mg-Ge alloys observed by TEM for different aging times. The age-precipitations structure of Al-Mg-Ge alloy has not been became clear. In this work, TEM observation was investigated the microstructure on Al-1.0mass%Mg2Ge alloy for difference aging times aged at 473K.

Ultraviolet spectra of Mg in liquid helium

International Nuclear Information System (INIS)

Moriwaki, Y.; Morita, N.

1999-01-01

Emission and absorption spectra of Mg atoms implanted in liquid helium have been observed in the ultraviolet region. We have presented a model of exciplex formation of Mg-He 10 and found that this model is more suitable for understanding the dynamics in the 3s3p 1 P→3s 21 S transition than the bubble model. (orig.)

The effect of different dialyzer membrane on the clearance of serum β2-MG in maintenance hemodialysis patients

International Nuclear Information System (INIS)

Lu Yun; Xue Jun; Lin Xiangtong; Deng Shouzhen; Li Ding

2001-01-01

Objective: To investigate the effect of different membrane on the clearance of serum β 2 -MG in maintenance hemodialysis patients. Method: 106 maintenance hemodialysis patients randomized divided into group A and group B. Group A used cellulose triacetate membrane (N-130E), Group B used polysulfone membrane (F6). The levels of serum β 2 -MG before and after hemodialysis were compared in Group A and B, respectively. Results: Before hemodialysis, the level of serum β 2 -MG was not significant different between Group A and B (46.74 ± 19.46 mg/L vs 47.49 ± 16.71 mg/L, P>0.05). In Group A, compared with that before hemodialysis, the level of serum β 2 -MG after hemodialysis decreased significantly. (46.74±19.46 mg/L vs 39.76 ±17.66 mg/L, before HD vs after HD, P 2 -MG between before and after hemodialysis (47.49±16.71 mg/L vs 50.19±22.76 mg/L, P>0.05). Conclusion: N-130E dialyzer is better than F6 dialyzer as the effect of clearance serum β 2 -MG is concerned

DSC and HRTEM investigation of the precipitates in Al-1.0%Mg{sub 2} Si-0.5%Ag alloy

Energy Technology Data Exchange (ETDEWEB)

Gaber, A.; Ali, A.M.; Zou, Y. [Toyama University (Japan). Venture Business Laboratory; Matsuda, K.; Ikeno, S. [Toyama University (Japan). Faculty of Engineering

2004-12-15

The understanding and control of nanoscale precipitation in an Al-1.0 wt-%Mg{sub 2} Si-0.5 wt-% Ag alloy during artificial aging is critical for achieving optimum mechanical properties. To achieve this objective, both differential scanning calorimetry (DSC) and high resolution transmission electron microscopy (HRTEM) have been utilised. The non-isothermal DSC thermograms exhibited eight reaction peaks; six are exothermic (precipitation) and two are endothermic (dissolution) reactions. The activation energies associated with the individual precipitates are determined. With the aid of HRTEM, the evolved precipitates have been characterised. (author)

IAEA INTOR workshop report, groups 2, 5, 7, 9, 10 and 15

International Nuclear Information System (INIS)

1980-02-01

In order to prove scientific feasibility of magnetic confinement fusion, large fusion devices are under construction in several countries (JT-60 in Japan, T-15 in U.S.S.R., TFTR in U.S.A. and JET in EC). International Tokamak Reactor (INTOR) Workshop was organized by the International Atomic Energy Agency (IAEA) to identify roles, objectives and characteristics of the next generation fusion device. This report is a compilation of the home task reports of six groups on INTOR engineering aspects by Japan Atomic Energy Research Institute for workshop sessions 2 and 3 held in 1979. Tasks of the respective groups are group 2: first wall/blanket/shield, group 5: magnetics, group 7: systems integration and structure, group 9: assembly and remote maintenance, group 10: radiation shielding and personnel access, group 15: safety and environment. (author)

Waste Area Group 10, Operable Unit 10-08, Remedial Investigation/Feasibility Study Annual Status Report for Fiscal Year 2006

Energy Technology Data Exchange (ETDEWEB)

R. P. Wells

2007-05-09

This report provides a status of the progress made in Fiscal Year 2006 on tasks identified in the Waste Area Group 10, Operable Unit 10-08, Remedial Investigation/Feasibility Study Work Plan. Major accomplishments include: (1) groundwater sampling and review of the groundwater monitoring data, (2) installation of a Sitewide groundwater-level monitoring network, (3) update of the Groundwater Monitoring and Field Sampling Plan of Operable Unit 10-08, (4) re-evaluation of the risk at Site TSF-08, (5) progress on the Operable Unit 10-08 Sitewide Groundwater Model.

Sexual asthenia: Tradamixina versus Tadalafil 5 mg daily

Science.gov (United States)

2012-01-01

Background Reduced libido is widely considered the most prominent symptomatic reflection of low testosterone (T) levels in men. Testosterone deficiency (TD) afflicts approximately 30% of men aged 40-79 years. This study seeks to evaluate the effect of a new natural compound “tradamixina “in order to improve male sexual function in elderly men, particularly libido and possible erectile dysfunction, versus administration of tadalafil 5 mg daily. Methods Seventy patients (67.3± 3.7 years) with stable marital relations and affected by reduced libido, with or without erectile dysfunction were recruited. They were randomly separated in 2 groups A-B of 35. Group A was administered twice a day a new compound “Tradamixina” (150 mg of Alga Ecklonia Bicyclis, 396 mg of Tribulus Terrestris and 144 mg of D-Glucosamine and N-Acetyl-D-Glucosamine) for two months, while Group B was administered tadalafil 5 mg daily, for two months. At visit and after 60 days of treatment patients were evaluated by means of detailed medical and sexual history, clinical examination, laboratory investigations (Total and Free T), instrumental examination (NPTR- nocturnal penile tumescence and rigidity test- with Rigiscan). Patients completed a self-administered IIEF questionnaire (The international index of erectile function) and SQoLM questionnaire (Sexual quality of life Questionnarie-Male). The results pre and post treatment were compared by Student t test (p<0.005). Results After 2 months of treatment in group A serum TT levels (230±18 ng/dl vs 671±14 ng/dl ) and FT levels(56± 2.4 pg/ml vs 120± 3.9pg/ml) increased, while in group B serum TT levels (245±12 ng/dl vs 247±15 ng/dl ) and FT levels(53± 0.3 pg/ml vs 55± 0.5pg/ml) increased not statistically significant. The patient’s numbers with negative NPTR improved after treatment in group A and B (15 vs 18 and 13 vs 25 respectively). The IIEF total score in group A increased after treatment with tradamixina (15±1.5 vs 29.77±1

Absorption-line detections of 10{sup 5}-10{sup 6} K gas in spiral-rich groups of galaxies

Energy Technology Data Exchange (ETDEWEB)

Stocke, John T.; Keeney, Brian A.; Danforth, Charles W.; Syphers, David; Yamamoto, H.; Shull, J. Michael; Green, James C.; Froning, Cynthia [Center for Astrophysics and Space Astronomy, Department of Astrophysical and Planetary Sciences, University of Colorado, 389 UCB, Boulder, CO 80309 (United States); Savage, Blair D.; Wakker, Bart; Kim, Tae-Sun [Department of Astronomy, University of Wisconsin, Madison, WI 53706 (United States); Ryan-Weber, Emma V.; Kacprzak, Glenn G., E-mail: john.stocke@colorado.edu [Centre for Astrophysics and Supercomputing, Swinburne University of Technology, VIC 3122 (Australia)

2014-08-20

Using the Cosmic Origins Spectrograph (COS) on the Hubble Space Telescope, the COS Science Team has conducted a high signal-to-noise survey of 14 bright QSOs. In a previous paper, these far-UV spectra were used to discover 14 'warm' (T ≥ 10{sup 5} K) absorbers using a combination of broad Lyα and broad O VI absorptions. A reanalysis of a few of this new class of absorbers using slightly relaxed fitting criteria finds as many as 20 warm absorbers could be present in this sample. A shallow, wide spectroscopic galaxy redshift survey has been conducted around these sight lines to investigate the warm absorber environment, which is found to be spiral-rich groups or cluster outskirts with radial velocity dispersions σ = 250-750 km s{sup –1}. While 2σ evidence is presented favoring the hypothesis that these absorptions are associated with the galaxy groups and not with the individual, nearest galaxies, this evidence has considerable systematic uncertainties and is based on a small sample size so it is not entirely conclusive. If the associations are with galaxy groups, the observed frequency of warm absorbers (dN/dz = 3.5-5 per unit redshift) requires them to be very extended as an ensemble on the sky (∼1 Mpc in radius at high covering factor). Most likely these warm absorbers are interface gas clouds whose presence implies the existence of a hotter (T ∼ 10{sup 6.5} K), diffuse, and probably very massive (>10{sup 11} M {sub ☉}) intra-group medium which has yet to be detected directly.

Hydrogen kinetics studies of MgH2-FeTi composites

Science.gov (United States)

Meena, Priyanka; Jangir, Mukesh; Singh, Ramvir; Sharma, V. K.; Jain, I. P.

2018-05-01

MgH2 + x wt% FeTi (x=10, 25, 50) nano composites were ball milled to get nano structured material and characterized for structural, morphological and thermal properties. XRD of the milled samples revealed the formation of MgH2, FeTi, Fe2Ti and H0.06FeTi phases. Morphological studies by SEM were undertaken to investigate the effect of hydrogenation of nanostructure alloy. EDX confirmed elemental composition of the as-prepared alloy. TGA studies showed higher desorption temperature for milled MgH2 compared to x wt% FeTi added MgH2. Activation energy for hydrogen desorption was found to be -177.90, -215.69, -162.46 and -87.93 kJ/mol for milled MgH2 and Mg2+x wt% FeTi (10, 25, 50), showing 89.97 kJ/ mol reduction in activation energy for 50 wt% alloy additives resulting in improved hydrogen storage capacity. DSC investigations were carried out to investigate the effect of alloy on hydrogen absorption behavior of MgH2.

Early effect on general interest, and short-term antidepressant efficacy and safety of agomelatine (25-50mg/day) and escitalopram (10-20mg/day) in outpatients with Major Depressive Disorder. A 12-week randomised double-blind comparative study.

Science.gov (United States)

Udristoiu, T; Dehelean, P; Nuss, Ph; Raba, V; Picarel-Blanchot, F; de Bodinat, C

2016-07-15

A double-blind, randomized, study was conducted in 29 centers in Romania to evaluate the effect of agomelatine 25-50mg/day (n=144 patients) on general interest, overall clinical efficacy, and functionality in comparison with escitalopram 10-20mg/day (n=143 patients) in out-patients diagnosed with moderate to severe Major Depressive Disorder (MDD). The primary endpoint of the study was the score difference between agomelatine and escitalopram were assessed on the item 13 of the Quick Inventory of Depressive Symptomatology (16-Item) Self-Report (QIDS-SR16) over the first week period. Secondary measures include the primary criterion on the 12-week period, the within-group evolution over 12 weeks of the 17-item Hamilton Depression Scale (HAM-D17) total score, CGI severity of illness (CGI-S) and CGI-I scores, and functionality by using the self-rated Sheehan Disability Scale (SDS). After one week, the mean General Interest score showed no statistically significant difference between treatments. Over 12 weeks, patients felt more and more interested in other people and activities than before having taken medication. Both agomelatine and escitalopram improved depressive symptoms and symptom-related functional impairment of patients. Both agomelatine and escitalopram were well-tolerated by patients. The strength of our results would benefit from additional data from trials using a similar design and other active comparators. There was no difference in week 1 changes of interest between agomelatine and escitalopram. The relatively good tolerability of agomelatine and escitalopram is confirmed. Copyright © 2016 Elsevier B.V. All rights reserved.

Microstructure and mechanical properties of Al10SiMg fabricated by pulsed laser powder bed fusion

Energy Technology Data Exchange (ETDEWEB)

Chou, R.; Ghosh, A.; Chou, S.C. [Aluminum Research Centre – REGAL, Department of Mining and Materials Engineering, McGill University, Montreal, QC, Canada H3A 0C5 (Canada); Paliwal, M. [Indian Institute of Technology Gandhinagar, Materials Science and Engineering, Gandhinagar, Gujarat (India); Brochu, M., E-mail: mathieu.brochu@mcgill.ca [Aluminum Research Centre – REGAL, Department of Mining and Materials Engineering, McGill University, Montreal, QC, Canada H3A 0C5 (Canada)

2017-03-24

A series of high-density Al10SiMg specimens were fabricated using a custom built pulsed laser powder bed fusion unit operating with a pulsed-laser source. The fabricated components were analyzed using optical microscopy, computerized tomography (CT), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) mapping, and X-ray diffraction (XRD). A significantly refined cellular microstructure was observed, where Al cell diameter refinement upto ~210 nm was obtained throughout the component. Age hardening T6 treatment was also performed to investigate the heat treatment response of this fine microstructure. The mechanical properties in the as-built condition were assessed by microhardness testing (136 HV) and compressive tests (true compressive yield strength of 380 MPa and true ultimate compressive strength of 485 MPa). On the other hand, the mechanical responses of T6 specimens displayed strength reduction while demonstrating enhanced ductility.

The use of a responder analysis to identify clinically meaningful differences in chronic urticaria patients following placebo- controlled treatment with rupatadine 10 and 20 mg.

Science.gov (United States)

Giménez-Arnau, A; Izquierdo, I; Maurer, M

2009-09-01

According to the EAACI/GA(2)LEN/EDF guidelines for urticaria management, modern non-sedating H1-antihistamines are the first-line symptomatic treatment for chronic urticaria. Two previous randomized clinical trials demonstrated rupatadine efficacy and safety in chronic urticaria treatment. However, a responder analysis to identify clinically meaningful differences in patients with chronic urticaria has not yet been performed. This analysis includes the pooled data from two randomized, double-blind, placebo-controlled, multicentre studies in which chronic urticaria patients were treated with rupatadine at different doses. Responder rates were defined as the percentage of patients after 4 weeks of treatment who exhibited a reduction of symptoms by at least 50% or 75% as compared to baseline. The variables analysed were as follows: Mean Pruritus Score (MPS), Mean Number of Wheals (MNW), and Mean Urticaria Activity Score (UAS). A total of 538 patients were included. This responder analysis, using different response levels, shows that the efficacy of rupatadine 10 mg and 20 mg is significantly better as compared to placebo in the treatment of chronic urticaria patients. Notably, treatment with rupatadine 20 mg daily resulted in a higher percentage of patients with response of 75% symptom reduction or better than rupatadine 10 mg. Our results support the use of higher than standard doses of non sedating antihistamines in chronic urticaria. We strongly recommend performing and reporting responder analyses for established and new drugs used by patients with chronic urticaria.

Thermoluminescence kinetic analysis and dosimetry features of MgSO4:Dy and MgSO4:Cu nano-rods

International Nuclear Information System (INIS)

Zahedifar, M.; Almasifard, F.; Sadeghi, E.; Biroon, M. Kashefi; Ramazani- Moghaddam-Arani, A.

2016-01-01

MgSO 4 :Dy and MgSO 4 :Cu nano-rods (NRs) were synthesized for the first time by semi co- precipitation method. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) were utilized for sample characterization. The optimum amount of dysprosium and copper concentrations were obtained both at 0.1 mol% in MgSO 4 :Dy and MgSO 4 :Cu NRs. T m -T stop and computerized glow curve deconvolution (CGCD) methods were used for identifying the number of component glow peaks and kinetic parameters of the synthesized NRs. Initial rise and variable heating rate methods were also used to ensure the reliability of obtained kinetic parameters. Results show that the TL sensitivity of MgSO 4 :Dy is about 7 times more than that of magnesium sulfate doped with Cu. The TL dose response of MgSO 4 :Dy and MgSO 4 :Cu NRs are linear up to absorbed dose of 10 KGy. Other TL dosimetry characteristics of the produced NRs are also presented and discussed. - Highlights: • MgSO4:Dy and MgSO4:Cu nano-rods were synthesized for the first time. • Thermoluminescence dosimetry properties were studied. • The nano-phosphors showed linear dose response up to very high dose levels. • The synthesized nano-rods have potential application for high dose dosimetry.

Bioequivalence of a single 400-mg dose of imatinib 100-mg oral tablets and a 400-mg tablet in healthy adult Korean volunteers.

Science.gov (United States)

Lee, Hae Won; Seong, Sook Jin; Park, Sung Min; Lee, Joomi; Gwon, Mi-Ri; Kim, Hyun-Ju; Lim, Sung Mook; Lim, Mi-Sun; Kim, Woomi; Yang, Dong Heon; Yoon, Young-Ran

2015-06-01

Imatinib mesylate (IM) is a selective tyrosine kinase inhibitor for the treatment of chronic myeloid leukemia and gastrointestinal stromal tumors. A new once-daily 400-mg film-coated tablet of imatinib has been developed by a pharmaceutical company in Korea. The present study was designed to assess and compare the PK parameters, bioavailability, and bioequivalence of the new imatinib 400-mg formulation (test) versus the conventional 100-mg formulation (reference) administered as a single 400-mg dose in healthy adult male volunteers. This randomized, open-label, single-dose, two-way crossover study was conducted in healthy Korean male volunteers. Eligible subjects were randomly assigned in a 1 : 1 ratio to receive 400 mg of the test (one 400-mg tablet) or reference (four 100-mg tablets) formulation, followed by a 2-week washout period and administration of the alternate formulation. Serial blood samples were collected at 0 (predose), 0.5, 1, 1.5, 2, 2.5, 3, 4, 6, 8, 10, 12, 24, 48, and 72 hours after administration. Plasma imatinib concentrations were determined using liquid chromatography coupled with tandem mass spectrometry. The formulations were to be considered bioequivalent if the 90% confidence intervals (CIs) of the adjusted geometric mean ratios for Cmax, AUC(0-t), and AUC(0-∞)ž were within the predetermined range of 0.80 - 1.25. In total, 35 subjects completed the study. No serious adverse event was reported during the study. The 90% CIs of the adjusted geometric mean ratios of the test formulation to the reference formulation for C(max), AUC(0-t) and AUC(0-∞)ž of imatinib were all within the bioequivalence criteria range of 0.8 - 1.25. The test formulation of imatinib met the Korean regulatory requirements for bioequivalence. Both imatinib formulations were well-tolerated in all subjects.

Ripple Field AC Losses in 10-MW Wind Turbine Generators With a MgB2 Superconducting Field Winding

DEFF Research Database (Denmark)

Liu, Dong; Polinder, Henk; Magnusson, Niklas

2016-01-01

Superconducting (SC) synchronous generators are proposed as a promising candidate for 10-20-MW direct-drive wind turbines because they can have low weights and small sizes. A common way of designing an SC machine is to use SC wires with high current-carrying capability in the dc field winding...... and the ac armature winding is made with copper conductors. In such generators, the dc field winding is exposed to ac magnetic field ripples due to space harmonics from the armature. In generator design phases, the ac loss caused by these ripple fields needs to be evaluated to avoid local overheating...... and an excessive cooling budget. To determine the applicability of different design solutions in terms of ac losses, this paper estimates the ac loss level of 10-MW wind generator designs employing a MgB2 SC field winding. The effects on ac losses are compared between nonmagnetic and ferromagnetic teeth...

Effect of Mg on the Microstructure and Corrosion Resistance of the Continuously Hot-Dip Galvanizing Zn-Mg Coating

Directory of Open Access Journals (Sweden)

Anping Dong

2017-08-01

Full Text Available The microstructure of continuously hot-dip galvanizing Zn-Mg coating was investigated in order to obtain the mechanism of the effects of Mg on the corrosion resistance. In this paper, the vertical section of the Zn-0.20 wt % Al-Mg ternary phase diagram near the Al-low corner was calculated. The results indicates that the phase composition of the Zn-0.20 wt % Al-Mg ternary phase diagram near the Al-low corner is the same as Zn-Mg binary phase diagram, suggesting Al in the Zn-Mg (ZM coatings mainly concentrates on the interfacial layer between the coating and steel substrate. The microstructure of continuously hot-dip galvanizing ZM coatings with 0.20 wt % Al containing 1.0–3.0 wt % Mg was investigated using tunneling electron microscopy (TEM. The morphology of Zn in the coating changes from bulk to strip and finally to mesh-like, and the MgZn2 changes from rod-like to mesh-like with the Mg content increasing. Al in the ZM coatings mainly segregates at the Fe2Al5 inhibition layer and the Mg added to the Zn bath makes this inhibition layer thinner and uneven. Compared to GI coating, the time of the first red rust appears increases by more than two-fold and expansion rate of red rust reduces by more than four-fold in terms of salt spray experiment. The ZM coating containing 2.0 wt % Mg has the best corrosion resistance. The enhanced corrosion resistance of ZM coatings mainly depends on different corrosion products.

Efficacy and tolerability of tamsulosin 0.4 mg in Asian patients with lower urinary tract symptoms secondary to benign prostatic hyperplasia refractory to tamsulosin 0.2 mg: a randomized placebo controlled trial.

Science.gov (United States)

Kim, Jung Jun; Han, Deok Hyun; Sung, Hyun Hwan; Choo, Seol Ho; Lee, Sung Won

2014-07-01

To evaluate the efficacy and safety of tamsulosin dose increase to 0.4 mg daily in Asian patients with lower urinary tract symptoms secondary to benign prostatic hyperplasia refractory to tamsulosin 0.2 mg treatment. We carried out a 12-week, single-center, randomized, placebo-controlled trial in 220 patients. Patients treated with 0.2 mg tamsulosin daily without other lower urinary tract symptoms secondary to benign prostatic hyperplasia medication for more than 3 months and refractory to this treatment were enrolled. We defined "refractory" as an International Prostate Symptom Score of 13 or greater and a maximum flow rate of 15 or under despite medication. Patients with a surgical history related to lower urinary tract symptoms secondary to benign prostatic hyperplasia or a postvoid residual of 150 mL or greater were excluded. Eligible patients were randomly assigned to the 0.4 mg group (two tablets of 0.2 mg tamsulosin once daily) or the 0.2 mg group (one tablet of 0.2 mg tamsulosin and one tablet of placebo once daily). International Prostate Symptom Score, maximum flow rate, blood pressure, heart rate, and adverse events were compared between the two groups at 4 weeks and 12 weeks. A total of 220 patients were enrolled and analyzed. There were no differences in baseline characteristics between the two groups. After 12 weeks of medication, the International Prostate Symptom Score was not different between the two groups. However, the improvement in maximum flow rate was greater in the 0.4 mg group than the 0.2 mg group (3.0 ± 0.48 mL/s vs -0.25 ± 0.30 mL/s, P Tamsulosin 0.4 mg appears to be a safe treatment regimen for treating lower urinary tract symptoms secondary to benign prostatic hyperplasia in Asian patients who do not respond to 0.2 mg treatment. Increasing the dose of tamsulosin results in a significant improvement in maximum flow rate without any increase in cardiovascular complications. © 2014 The

A Raman spectroscopic study of the structural aspects of K2MgCl4 and Cs2MgCl4 as solid single crystals and molten salts

International Nuclear Information System (INIS)

Brooker, M.H.

1975-01-01

Polarized Raman spectra have been obtained for oriented single crystals of K 2 MgCl 4 and Cs 2 MgCl 4 at 77 and 298 K. The data are in excellent agreement with factor group analyses based on the space groups I 4 /mmm (D 17 4 /subh/) and Pnma (D 16 2 /subh/) for the K 2 MgCl 4 and Cs 2 MgCl 4 crystals. In K 2 MgCl 4 the magnesium is surrounded by six chloride ions in a distorted octahedral arrangement with a network structure such that neighboring octahedra share corners. In Cs 2 MgCl 4 a discrete tetrahedral MgCl 4 2- species is present. The 35 Cl-- 37 Cl isotopic splitting of the symmetric stetching mode of the tetrahedral MgCl 4 2- species has been resolved at 77 K and is similar to that observed for CCl 4 . Raman spectra for the high temperature solids and molten salts suggest that the coordination number of magnesium changes from six in solid K 2 MgCl 4 to four in the melt, whereas Cs 2 MgCl 4 melts with retention of the MgCl 4 2- tetrahedral complex. Additional evidence is presented to support previous reports that the MgCl 4 2- tetrahedral species is the principal complex ion in the melts, although a fraction of the magnesium appears to be present in a polynuclear complex, perhaps Mg 2 Cl 6 2-

Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using X-ray computed tomography

Energy Technology Data Exchange (ETDEWEB)

Maskery, I., E-mail: Ian.Maskery@nottingham.ac.uk [Additive Manufacturing & 3D Printing Research Group, Faculty of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Aboulkhair, N.T. [Bioengineering Research Group, Faculty of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Corfield, M.R. [Power Electronics Machines & Control Research Group, Faculty of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Tuck, C. [Additive Manufacturing & 3D Printing Research Group, Faculty of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Clare, A.T. [Advanced Manufacturing Research Group, Faculty of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Leach, R.K.; Wildman, R.D.; Ashcroft, I.A.; Hague, R.J.M. [Additive Manufacturing & 3D Printing Research Group, Faculty of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom)

2016-01-15

We used X-ray computed tomography (CT), microscopy and hardness measurements to study Al–Si10–Mg produced by selective laser melting (SLM). Specimens were subject to a series of heat treatments including annealing and precipitation hardening. The specimen interiors were imaged with X-ray CT, allowing the non-destructive quantification and characterisation of pores, including their spatial distribution. The specimens had porosities less than 0.1%, but included some pores with effective cross-sectional diameters up to 260 μm. The largest pores were highly anisotropic, being flat and lying in the plane normal to the build direction. Annealing cycles caused significant coarsening of the microstructure and a reduction of the hardness from (114 ± 3) HV, in the as-built state, to (45 ± 1) HV, while precipitation hardening increased this to a final hardness of (59 ± 1) HV. The pore size and shape distributions were unaffected by the heat treatments. We demonstrate the applicability of CT measurements and quantitative defect analysis for the purposes of SLM process monitoring and refinement. - Highlights: • We examined SLM Al–Si10–Mg with X-ray CT, microscopy and hardness measurements. • The size, shape and position distributions of the internal pores were determined. • Heat treatments alter the microstructure and hardness, but the pores are unaffected. • The largest pores are highly anisotropic, being at or disc-like in the xy plane. • CT and statistical analysis can play a role in improving the manufacturing process.

Photoluminescence properties of color-tunable SrMgAl10O17:Eu2+,Mn2+ phosphors for UV LEDs

International Nuclear Information System (INIS)

Ju Guifang; Hu Yihua; Chen Li; Wang Xiaojuan

2012-01-01

Aluminate phosphors SrMgAl 10 O 17 codoped with Eu 2+ and Mn 2+ ions were prepared by solid-state reaction. The phase structure and photoluminescence properties of the as-prepared phosphors were characterized by powder X-ray diffraction, photoluminescence excitation and emission spectra. Upon excitation of UV light, two broad emission bands centered at 470 and 515 nm were observed, and they were assigned to Eu 2+ and Mn 2+ emissions, respectively. The emission color of the phosphors can be tuned from blue to cyan and finally to green by adjusting the concentration ratios of Eu 2+ and Mn 2+ . Effective energy transfer occurs from Eu 2+ to Mn 2+ in the host due to the spectral overlap between the emission band of Eu 2+ and the excitation bands of Mn 2+ . The energy transfer mechanism was demonstrated to be electric dipole–quadrupole interaction. The energy transfer efficiency and critical distance were also calculated. The phosphors exhibit strong absorption in near UV spectral region and therefore they are potentially useful as UV-convertible phosphors for white LEDs. - Highlights: ► The strong absorption of phosphors matches well with the emission band of UV LED. ► The energy transfer from Eu 2+ to Mn 2+ in SrMgAl 10 O 17 was investigated in detail. ► The emission color can be tuned by adjusting the content of Eu 2+ and Mn 2+ . ► Two methods were employed to calculate the critical distance of energy transfer.

The Abundance of Mg in the Interstellar Medium

Science.gov (United States)

Fitzpatrick, Edward L.

1997-06-01

An empirical determination of the f-values of the far-UV Mg II λλ1239, 1240 lines is reported. The strong near-UV Mg II λλ2796, 2803 lines are generally highly saturated along most interstellar sight lines outside the local interstellar medium (ISM) and usually yield extremely uncertain estimates of Mg+ column densities in interstellar gas. Since Mg+ is the dominant form of Mg in the neutral ISM, and since Mg is expected to be a significant constituent of interstellar dust grains, the far-UV lines are critical for assessing the role of this important element in the ISM. This study consists of complete component analyses of the absorption along the lines of sight toward HD 93521 in the Galactic halo and ξ Persei and ζ Ophiuchi in the Galactic disk, including all four UV Mg+ lines and numerous other transitions. The three analyses yield consistent determinations of the λλ1239, 1240 f-values, with weighted means of (6.4 +/- 0.4) × 10-4 and (3.2 +/- 0.2) × 10-4, respectively. These results are a factor of ~2.4 larger than a commonly used theoretical estimate, and a factor of ~2 smaller than a recently suggested empirical revision. The effects of this result on gas- and dust-phase abundance measurements of Mg are discussed. Based on observations with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, under NASA contract NAS5-2655. This Letter is dedicated to the memory of Professor Lyman Spitzer Jr. He was a great guy.

Ropivacaine 7.5 mg/mL for Caesarean Section

Directory of Open Access Journals (Sweden)

N. K. Nguyen

2010-01-01

Full Text Available Background. Pain after Caesarean delivery is partly related to Pfannenstiel incision, which can be infiltrated with local anaesthetic solutions. Methods. A double- blind randomized control trial was designed to assess the analgesic efficacy of 7.5 mg/mL ropivacaine solution compared to control group, in two groups of one hundred and forty four parturients for each group, who underwent Caesarean section under spinal anaesthesia: group R (ropivacaine group and group C (control group. All parturients also received spinal sufentanil (2.5 g. Results. Ropivacaine infiltration in the Pfannenstiel incision for Caesarean delivery before wound closure leads to a reduction of 30% in the overall consumption of analgesics (348 550 mg for group R versus 504 426 mg for group C with <.05, especially opioids in the first 24 hours, but also significantly increases the time interval until the first request for an analgesic (4 h 20 min ± 2 h 26 for group R versus 2 h 42 ± 1 h 30 for group C. The P values for the two groups were: <.0001 for paracetamol, <.0001 for ketoprofen and P for nalbuphine which was the most significant. There is no significant difference in the threshold of VAS in the two series. Conclusion. This technique can contribute towards a programme of early rehabilitation in sectioned mothers, with earlier discharge from the post-labour suite.

Mg doping of GaN by molecular beam epitaxy

International Nuclear Information System (INIS)

Lieten, R R; Buchowicz, G; Dubon, O; Motsnyi, V; Zhang, L; Cheng, K; Leys, M; Degroote, S; Borghs, G

2011-01-01

We present a systematic study on the influence of growth conditions on the incorporation and activation of Mg in GaN layers grown by plasma-assisted molecular beam epitaxy. We show that high quality p-type GaN layers can be obtained on GaN-on-silicon templates. The Mg incorporation and the electrical properties have been investigated as a function of growth temperature, Ga : N flux ratio and Mg : Ga flux ratio. It was found that the incorporation of Mg and the electrical properties are highly sensitive to the Ga : N flux ratio. The highest hole mobility and lowest resistivity were achieved for slightly Ga-rich conditions. In addition to an optimal Ga : N ratio, an optimum Mg : Ga flux ratio was also observed at around 1%. We observed a clear Mg flux window for p-type doping of GaN : 0.31% 17 cm -3 and a mobility of 15 cm 2 V -1 s -1 . Temperature-dependent Hall effect measurements indicate an acceptor depth in these samples of 100 meV for a hole concentration of 5.5 x 10 17 cm -3 . The corresponding Mg concentration is 5 x 10 19 cm -3 , indicating approximately 1% activation at room temperature. In addition to continuous growth of Mg-doped GaN layers we also investigated different modulated growth procedures. We show that a modulated growth procedure has only limited influence on Mg doping at a growth temperature of 800 deg. or higher. This result is thus in contrast to previously reported GaN : Mg doping at much lower growth temperatures of 500 deg. C.

Spectroscopic, thermal, and electrical properties of MgO/ polyvinyl pyrrolidone/ polyvinyl alcohol nanocomposites

Science.gov (United States)

Mohammed, Gh.; El Sayed, Adel M.; Morsi, W. M.

2018-04-01

In this study, we aimed to control the optical and electrical properties of polyvinyl alcohol (PVA) in order to broaden its industrial and technological applications, which we achieved by blending PVA with polyvinyl pyrrolidone (PVP) and adding sol-gel prepared MgO nanopowder. The blended film and nanocomposite films were prepared using the solution casting technique. X-ray diffraction analyses showed that the crystallite size was ∼18.4 nm for MgO and the highest degree of crystallinity (XC) in the films was about 24.34% at 1.0 wt% MgO. High resolution transmission electron microscopy determined the nanoribbon morphology of MgO. Scanning electron microscopy (SEM) indicated the uniform distribution of the MgO nanoribbons on the surfaces of the PVA/PVP films. SEM and Fourier transform infrared spectroscopy also confirmed the interaction between the blend and MgO fillers. The effects of the additives on the glass transition (Tg) and melting (Tm) temperatures were evaluated by differential thermal analysis and differential scanning calorimetry. The appearance of one melting point confirmed the miscibility of the two polymers. According to ultraviolet-visible-near infrared spectroscopy measurements, the optical properties and optical constants of PVA could be adjusted by the addition of PVP and MgO, where the optical band gap (Eg) determined for PVA increased with the PVP content, whereas it decreased to 4.8 eV as the MgO content increased. The DC conductivity (σdc) of the films increased whereas the activation energy (Ea) decreased after the addition of MgO, possibly because the nanoribbon shape fixed the preferred conducting pathways. In addition, MgO could break the H-bond in sbnd OH groups of the blends to allow the free movement of the molecular chains.

Electrical and magnetic properties of FM/MgO/FM (FM  =  Co90Fe10, Fe20Ni80) heterostructures

International Nuclear Information System (INIS)

Avilés-Félix, L; González, J; Gómez, J E; Sirena, M

2016-01-01

In this paper we present the development and characterization of FM/MgO/FM (FM  =  Co 90 Fe 10 , Fe 20 Ni 80 ) heterostructures. The magnetic order of the structures, magnetic anisotropy and interlayer exchange coupling were characterized by magnetization measurements. The influence of the substrate temperature during growth on the magnetic properties and topographical features of the bottom electrode was also explored. Higher values of the coercive field were achieved increasing the substrate temperature during deposition of the bottom electrode. Patterned magnetic tunnel junctions were grown on Si(1 0 0) and MgO(1 0 0). The junctions consist of square pillars with different areas (1600, 625, 100 and 25 μ m 2 ) fabricated by optical lithography. I ( V ) curves obtained with conducting atomic force microscopy of the patterned junctions were performed at room temperature in order to explore the reproducibility of the transport properties of the insulating barrier. The results show a more insulating behavior of the junctions grown on Si(1 0 0), with very good control and a high reproducibility of the transport properties of the MgO insulating barrier. (paper)

Nanostructured Layered Cathode for Rechargeable Mg-Ion Batteries.

Science.gov (United States)

Tepavcevic, Sanja; Liu, Yuzi; Zhou, Dehua; Lai, Barry; Maser, Jorg; Zuo, Xiaobing; Chan, Henry; Král, Petr; Johnson, Christopher S; Stamenkovic, Vojislav; Markovic, Nenad M; Rajh, Tijana

2015-08-25

Nanostructured bilayered V2O5 was electrochemically deposited within a carbon nanofoam conductive support. As-prepared electrochemically synthesized bilayered V2O5 incorporates structural water and hydroxyl groups, which effectively stabilizes the interlayers and provides coordinative preference to the Mg(2+) cation in reversible cycling. This open-framework electrode shows reversible intercalation/deintercalation of Mg(2+) ions in common electrolytes such as acetonitrile. Using a scanning transmission electron microscope we demonstrate that Mg(2+) ions can be effectively intercalated into the interlayer spacing of nanostructured V2O5, enabling electrochemical magnesiation against a Mg anode with a specific capacity of 240 mAh/g. We employ HRTEM and X-ray fluorescence (XRF) imaging to understand the role of environment in the intercalation processes. A rebuilt full cell was tested by employing a high-energy ball-milled Sn alloy anode in acetonitrile with Mg(ClO4)2 salt. XRF microscopy reveals effective insertion of Mg ions throughout the V2O5 structure during discharge and removal of Mg ions during electrode charging, in agreement with the electrode capacity. We show using XANES and XRF microscopy that reversible Mg intercalation is limited by the anode capacity.

Discharge behaviour of Mg-Al-Pb and Mg-Al-Pb-In alloys as anodes for Mg-air battery

International Nuclear Information System (INIS)

Wang, Naiguang; Wang, Richu; Peng, Chaoqun; Peng, Bing; Feng, Yan; Hu, Chengwang

2014-01-01

Highlights: • We investigate the effect of indium on the discharge behaviour of Mg-Al-Pb alloy. • We evaluate the performance of Mg-air batteries with Mg-Al-Pb and Mg-Al-Pb-In anodes. • We analyze the activation mechanism of Mg-Al-Pb-In alloy in the discharge process. - Abstract: The discharge behaviour of Mg-Al-Pb and Mg-Al-Pb-In alloys in 3.5 wt.% NaCl solution is investigated by electrochemical techniques, and compared with that of pure magnesium. The results show that Mg-Al-Pb-In alloy provides a more negative potential and exhibits a higher utilization efficiency in contrast with Mg-Al-Pb alloy and pure magnesium during the half-cell test at a large current density, and gives desirable discharge performance when used as anode for Mg- air battery. The peak power density of the Mg-air battery with Mg-Al-Pb-In anode is 94.5 mW cm −2 , which is comparable with those of Mg-H 2 O 2 semi-fuel batteries. Moreover, the activation mechanism of Mg-Al-Pb-In alloy during the discharge process is also analyzed

Dimensional Accuracy and Surface Roughness Analysis for AlSi10Mg Produced by Selective Laser Melting (SLM

Directory of Open Access Journals (Sweden)

Kamarudin K.

2016-01-01

Full Text Available Selective Laser Melting (SLM is an Additive Manufacturing (AM technique that built 3D part in a layer-by-layer method by melting the top surface layer of a powder bed with a high intensity laser according to sliced 3D CAD data. AlSi10Mg alloy is a traditional cast alloy that is broadly used for die-casting process and used in automotive industry due its good mechanical properties. This paper seeks to investigate the requirement SLM in rapid tooling application. The feasibility study is done by examining the surface roughness and dimensional accuracy as compared to the benchmark part produced through the SLM process with constant parameters. The benchmark produced by SLM shows the potential of SLM in a manufacturing application particularly in moulds.

Low Temperature Mechanical Properties of Scandium-Modified Al-Zn-Mg-Cu Alloys

National Research Council Canada - National Science Library

Senkov, O

2002-01-01

Tensile properties of three wrought alloys, (1) Al-10Zn-3Mg-1.2Cu-0.15Zr, (2) Al-10Zn-3Mg-1.2Cu-0.15Zr-0.39Mn-0.49Sc, and (3) Al-12Zn-3Mg-1.2Cu-0.15Zr-0.39Mn-0.49Sc were studied in T6 and T7 conditions at 298K and 77K...

Randomised clinical trial: daily pantoprazole magnesium 40 mg vs. esomeprazole 40 mg for gastro-oesophageal reflux disease, assessed by endoscopy and symptoms.

Science.gov (United States)

Moraes-Filho, J P; Pedroso, M; Quigley, E M M

2014-01-01

Pantoprazole magnesium (pantoprazole-Mg) may display extended inhibition of the proton pump with the potential for improved clinical efficacy in gastro-oesophageal reflux disease (GERD). To compare the efficacy of pantoprazole-Mg and esomeprazole in GERD. Gastro-oesophageal reflux disease (Los Angeles grades A-D) patients were randomised to 4 weeks of treatment with pantoprazole-Mg (n = 290) or esomeprazole (n = 288), both 40 mg once daily, in this multicentre (14 Brazilian sites in 9 cities), double-blind study, with an additional 4 weeks' treatment in nonresponding patients. Severity of oesophagitis (at endoscopy) and GERD-related symptoms (ReQuest-GI) were assessed. The primary end point was the proportion of patients in complete remission (ReQuest-GI score <1.73 plus endoscopic healing) at week 4. Complete remission occurred in 61% of patients in each treatment group at 4 weeks (primary endpoint) and in 81% and 79% of patients in the pantoprazole-Mg and esomeprazole groups at 8 weeks, with no significant differences. Mucosal healing rates were high and not significantly different. At 8 weeks, symptom relief with pantoprazole-Mg was significantly greater than that with esomeprazole (91.6% vs. 86.0%, P = 0.0370) because of continued improvement in symptoms with pantoprazole-Mg from week 4 to week 8 (P = 0.0206). Pantoprazole-Mg 40 mg was at least as effective as esomeprazole 40 mg for complete remission and the mucosal healing rate was high. Symptom relief with pantoprazole-Mg continued to improve from 4 to 8 weeks and was greater than that with esomeprazole at week 8, suggesting an extended period of treatment effect (ClinicalTrials.gov identifier: NCT01132638). © 2013 John Wiley & Sons Ltd.

Coenzyme Q10 supplementation decreases statin-related mild-to-moderate muscle symptoms: a randomized clinical study.

Science.gov (United States)

Skarlovnik, Ajda; Janić, Miodrag; Lunder, Mojca; Turk, Martina; Šabovič, Mišo

2014-11-06

Statin use is frequently associated with muscle-related symptoms. Coenzyme Q10 supplementation has yielded conflicting results in decreasing statin myopathy. Herein, we tested whether coenzyme Q10 supplementation could decrease statin-associated muscular pain in a specific group of patients with mild-to-moderate muscle symptoms. Fifty patients treated with statins and reporting muscle pain were recruited. The Q10 group (n=25) received coenzyme Q10 supplementation over a period of 30 days (50 mg twice daily), and the control group (n=25) received placebo. The Brief Pain Inventory (BPI) questionnaire was used and blood testing was performed at inclusion in the study and after 30 days of supplementation. The intensity of muscle pain, measured as the Pain Severity Score (PSS), in the Q10 group was reduced from 3.9±0.4 to 2.9±0.4 (PPain Interference Score (PIS) after Q10 supplementation was reduced from 4.0±0.4 to 2.6±0.4 (Pstatin-related muscle symptoms in 75% of patients. The relative values of PSS and PIS significantly decreased (-33.1% and -40.3%, respectively) in the Q10 group compared to placebo group (both Pmuscle enzymes or cholesterol values were found. The present results show that coenzyme Q10 supplementation (50 mg twice daily) effectively reduced statin-related mild-to-moderate muscular symptoms, causing lower interference of statin-related muscular symptoms with daily activities.

Corrosion Behavior of Heat-Treated AlSi10Mg Manufactured by Laser Powder Bed Fusion

Directory of Open Access Journals (Sweden)

Marina Cabrini

2018-06-01

Full Text Available This experimental work is aimed at studying the effect of microstructural modifications induced by post-processing heat treatments on the corrosion behavior of silicon-aluminum alloys produced by means of laser powder bed fusion (LPBF. The manufacturing technique leads to microstructures characterized by the presence of melt pools, which are quite different compared to casting alloys. In this study, the behavior of an AlSi10Mg alloy was evaluated by means of intergranular corrosion tests according to ISO 11846 standard on heat-treated samples ranging from 200 to 500 °C as well as on untreated samples. We found that temperatures above 200 °C reduced microhardness of the alloy, and different corrosion morphologies occurred due to the modification of both size and distribution of silicon precipitates. Selective penetrating attacks occurred at melt pool borders. The intergranular corrosion phenomena were less intense for as-produced specimens without heat treatments compared to the heat-treated specimens at 200 and 300 °C. General corrosion morphologies were noticed for specimens heat treated at temperatures exceeding 400 °C.

The effect of the MgO buffer layer thickness on magnetic anisotropy in MgO/Fe/Cr/MgO buffer/MgO(001)

Energy Technology Data Exchange (ETDEWEB)

Kozioł-Rachwał, Anna, E-mail: a.koziolrachwal@aist.go.jp [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, al. Mickiewicza 30, 30-059 Kraków (Poland); Nozaki, Takayuki; Zayets, Vadym; Kubota, Hitoshi; Fukushima, Akio; Yuasa, Shinji [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); Suzuki, Yoshishige [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan)

2016-08-28

The relationship between the magnetic properties and MgO buffer layer thickness d was studied in epitaxial MgO/Fe(t)/Cr/MgO(d) layers grown on MgO(001) substrate in which the Fe thickness t ranged from 0.4 nm to 1.1 nm. For 0.4 nm ≤ t ≤ 0.7 nm, a non-monotonic coercivity dependence on the MgO buffer thickness was shown by perpendicular magneto-optic Kerr effect magnetometry. For thicker Fe films, an increase in the buffer layer thickness resulted in a spin reorientation transition from perpendicular to the in-plane magnetization direction. Possible origins of these unusual behaviors were discussed in terms of the suppression of carbon contamination at the Fe surface and changes in the magnetoelastic anisotropy in the system. These results illustrate a method to control magnetic anisotropy in MgO/Fe/Cr/MgO(d) via an appropriate choice of MgO buffer layer thickness d.

Mg-enriched erythrite from Bou Azzer, Anti-Atlas Mountains, Morocco: geochemical and spectroscopic characteristics

Science.gov (United States)

Dumańska-Słowik, Magdalena; Pieczka, Adam; Natkaniec-Nowak, Lucyna; Kunecki, Piotr; Gaweł, Adam; Heflik, Wiesław; Smoliński, Wojciech; Kozub-Budzyń, Gabriela

2018-06-01

Supergene Mg-enriched erythrite, with an average composition (Co2.25Mg0.58Ni0.14Fe0.04Mn0.02 Zn0.02) (As1.97PMorocco. The unit cell parameters of monoclinic Mg-enriched erythrite [space group C2/ m, a = 10.252(2) Å, b = 13.427(3) Å, c = 4.757(3) Å, ß = 105.12(1)°] make the mineral comparable with erythrite from other localities. The composition of the sample represents the solid solution between erythrite, hörnesite and annabergite, that is, the nearest to the endmember erythrite. However, Mg-enriched erythrite forming the crystal exhibits variable compositions, especially in Mg and Co contents, with Mg increasing from 0.32 up to 1.39 apfu, and Co decreasing from 2.53 to 1.50 apfu, which manifests in the fine compositional oscillatory zoning. It is the highest content of Mg in erythrite structure reported so far. The most intensive Raman active ν3 and ν1 bands, recorded for the crystal's zones with maximum Mg contents, occur at 865 and 800 cm- 1 and are shifted towards higher wavenumbers, where normally hörnesite Raman bands appear. The characteristic oscillatory zoning texture results from varying contents of main and trace elements mobilized from the host ores (Co arsenides, mainly skutterudite) and rock-forming minerals (among others, dolomite) by the solutions in the oxidation zone of the ore deposits. The heating of the Mg-enriched erythrite up to 1000 °C leads to the crystallization of the water-free (Co,Mg)3(AsO4)2 phase.

Microstructural evolution in Mg-rich Mg-Zn-Y alloys

International Nuclear Information System (INIS)

Biswas, T.; Ranganathan, S.; Nair, S.; Bajargan, G.

2005-01-01

Mg-rich Mg-Zn-Y alloys with nominal compositions Mg 97 Zn 1 Y 2 , Mg 97 Zn 2 Y 1 , Mg 92 Zn 6.5 Y 1.5 and Mg 97-x Zn 1 Y 2 Zr x have been chosen for the present study. These alloys are prepared by using sand casting mold. The sand cast alloys are remelted and subjected to copper mold casting and melt spinning techniques. The effect of cooling rate on microstructures was studied. It is observed that the size of the precipitates decreases with an increase of cooling rate. The formation of nano precipitates results in higher strength of the alloy as compared to the conventional alloys. The microstructures of melt spun ribbons are compared with RS/PM (rapidly solidified power metallurgy) Mg 97 Zn 1 Y 2 alloy, obtained from a different source. (author)

Randomized clinical trial of dexketoprofen/tramadol 25 mg/75 mg in moderate-to-severe pain after total hip arthroplasty.

Science.gov (United States)

McQuay, H J; Moore, R A; Berta, A; Gainutdinovs, O; Fülesdi, B; Porvaneckas, N; Petronis, S; Mitkovic, M; Bucsi, L; Samson, L; Zegunis, V; Ankin, M L; Bertolotti, M; Pizà-Vallespir, B; Cuadripani, S; Contini, M P; Nizzardo, A

2016-02-01

The aim was to evaluate the analgesic efficacy and safety of the dexketoprofen/tramadol 25 mg/75 mg fixed-dose combination vs dexketoprofen (25 mg) and tramadol (100 mg) in moderate-to-severe acute pain after total hip arthroplasty. This was a randomized, double-blind, parallel-group study in patients experiencing pain of at least moderate intensity on the day after surgery, compared with placebo at first administration to validate the pain model. The study drug was administered orally every 8 h throughout a 5 day period. Rescue medication, metamizole 500 mg, was available during the treatment period. The evaluation of efficacy was based on patient assessments of pain intensity and pain relief. The primary end point was the mean sum of the pain intensity difference values throughout the first 8 h (SPID8). Overall, 641 patients, mean age 62 (range 29-80) yr, were analysed; mean (sd) values of SPID8 were 247 (157) for dexketoprofen/tramadol, 209 (155) for dexketoprofen, 205 (146) for tramadol, and 151 (159) for placebo. The primary analysis confirmed the superiority of the combination over dexketoprofen 25 mg (P=0.019; 95% confidence interval 6.4-73) and tramadol 100 mg (P=0.012; 95% confidence interval 9.5-76). The single components were superior to placebo (P<0.05), confirming model sensitivity. Most secondary analyses supported the superiority of the combination. The incidence of adverse drug reactions was low and similar among active treatment groups. The efficacy results confirmed the superiority of dexketoprofen/tramadol over its single components, even at higher doses (tramadol), with a safety profile fully in line with that previously known for these agents in monotherapy. EudraCT 2012-004548-31 (https://www.clinicaltrialsregister.eu/ctr-search/search?query=eudract_number:2012-004548-31);ClinicalTrials.gov NCT01902134 (https://www.clinicaltrials.gov/ct2/show/NCT01902134?term=NCT01902134&rank=1). © The Author 2016. Published by Oxford University Press on

Effect of ionizing radiation on Ca2+-ATPase and Mg2+-ATPase: the role of ligands

International Nuclear Information System (INIS)

Dreval', V.I.

1994-01-01

The change of Ca 2+ -ATPase and Mg 2+ -ATPase activity in plasma membranes of thymocytes irradiated with doses of 10 2 , 10 3 and 10 4 Gy in the presence of Ca 2+ , Mg 2+ and ATP was studied. Stabilizing effect of Ca 2+ and Mg 2+ on Ca 2+ -ATPase and ATP on Mg 2+ -ATPase under irradiation was established

Abnormal devitrification behavior and mechanical response of cold-rolled Mg-rich Mg-Cu-Gd metallic glasses

International Nuclear Information System (INIS)

Lee, J.I.; Kim, J.W.; Oh, H.S.; Park, J.S.; Park, E.S.

2016-01-01

Abnormal devitrification behavior and mechanical response of Mg 75 Cu 15 Gd 10 (relatively strong glass former with higher structural stability) and Mg 85 Cu 5 Gd 10 (relatively fragile glass former with lower structural stability) metallic glasses, fabricated by repeated forced cold rolling, have been investigated. When metallic glasses were cold-rolled up to a thickness reduction ratio of ∼33%, the heat of relaxation (ΔH relax. ) below T g of the cold-rolled specimens was reduced, which indicates the formation of local structural ordering via cold rolling due to stress-induced relaxation. The local structural ordering results in abnormal devitrification behavior, such as higher resistance of glass-to-supercooled liquid transition and delayed growth, in the following heat treatment due to increased nuclei density and pinning site. In particular, the fragility index, m, could assist in understanding structural stability and local structural variation by mechanical processing as well as compositional tuning. Indeed, we examine the shear avalanche size to rationalize the variation of the deformation unit size depending on the structural instability before and after cold rolling. The deformation mode in Mg 85 Cu 5 Gd 10 metallic glass might change from self-organized critical state to chaotic state by cold rolling, which results in unique hardening behavior under the condition for coexisting well distributed local structural ordering and numerous thinner shear deformed areas. These results would give us a guideline for atomic scale structural manipulation of metallic glasses, and help develop novel metallic glass matrix composites with optimal properties through effective mechanical processing as well as heat treatment.

The cardioprotective effect of vanillic acid on hemodynamic parameters, malondialdehyde, and infarct size in ischemia-reperfusion isolated rat heart exposed to PM10

Directory of Open Access Journals (Sweden)

Esmat Radmanesh

2017-07-01

Full Text Available Objective(s: Particulate matter (PM exposure can promote cardiac ischemia and myocardial damage. The effects of PM10 on hemodynamic parameters, lipid peroxidation, and infarct size induced by ischemia-reperfusion injury and the protective effects of vanillic acid (VA in isolated rat heart were investigated. Materials and Methods: Eighty male Wistar rats (250–300 g were divided into 8 groups (n=10: Control, Sham, VAc, VA, PMa (0.5 mg/kg PM, intratracheal instillation, PMb (2.5 mg/kg PM, intratracheal instillation, PMc (5 mg/kg PM, intratracheal instillation, and PMc + VA (5 mg/kg PM, intratracheal instillation; and 10 mg/kg vanillic acid, gavage for 10 days. PM10 was instilled into the trachea in two stages, within 48 hr. After isolating the hearts and transfer to a Langendorff apparatus, hearts were subjected to 30 min ischemia and 60 min reperfusion. Hemodynamic parameters (±dp/dt, LVSP, LVDP, and RPP, production of lipid peroxidation (MDA, and infarct size were assessed. Results: A significant decrease in ±dp/dt, LVSP, LVDP and RPP occurred in PM groups. A significant increase in MDA and myocardial infarct size occurred in PM groups. A significant increase in LVDP, LVSP, ±dp/dt, RPP and decrease in infarct size, MDA, and myocardial dysfunction was observed in groups that received vanillic acid after ischemia–reperfusion. Conclusion: It was demonstrated that PM10 increases MDA, as well as the percentage of cardiac infarct size, and has negative effects on hemodynamic parameters. This study suggests that vanillic acid may serve as an adjunctive treatment in delaying the progression of ischemic heart disease.

Ultraviolet detecting properties of amorphous MgInO thin film phototransistors

International Nuclear Information System (INIS)

Lu, Huiling; Bi, Xiaobin; Zhang, Shengdong; Zhou, Hang

2015-01-01

The ultraviolet (UV) detecting properties of Mg doped In 2 O 3 (MgInO or MIO) bottom gate thin film transistors (TFTs) were investigated. The optical measurements show that the introduction of Mg dopants effectively widens the optical band gap of In 2 O 3 . The cutoff wavelength of MIO films is pushed to deep UV as Mg content increases. Fabricated MIO TFTs with high Mg content demonstrate appraisable UV detecting properties with a dark current of 10 −14 A, a UV to visible rejection ratio of 10 3 , a responsivity of 3.2 A/W (300 nm) and a cutoff wavelength of 320 nm, which can be put to good use in deep UV detection. The dynamic photo-response measurement shows that the persistent photo-conductivity (PPC) effect can be alleviated by imposing a transient positive gate pulse. (paper)

Efficacy and Safety of Terbinafine 500 mg Once Daily in Patients with Dermatophytosis.

Science.gov (United States)

Babu, P Ravindra; Pravin, A J S; Deshmukh, Gaurav; Dhoot, Dhiraj; Samant, Aniket; Kotak, Bhavesh

2017-01-01

Dermatophytosis are the most common fungal infections globally. Terbinafine is considered to have good potency against dermatophytes, but resistance to terbinafine is on the rise. The objective of this study was to evaluate the efficacy and safety of terbinafine 500 mg given once daily in treatment of patients with superficial dermatophytosis. It was a retrospective questionnaire-based survey. Each doctor was given survey questionnaire booklet containing survey forms. Clinical response was graded according to the improvement in the affected lesion. Mycological cure was defined as negative microscopy under potassium hydroxide examination and a negative culture in Sabouraud's dextrose agar. Patients were divided into three groups depending on the duration of therapy, Group A - terbinafine 500 mg for 2 weeks, Group B - terbinafine 500 mg for 4 weeks, and Group C - terbinafine 500 mg for 6 weeks. Total 50 doctors completed the survey involving 440 patients. In Group A, out of 194 patients, 87% ( n = 169) patients showed very good response. In Group B, out of 211 patients, 92% ( n = 194) of the patients showed very good response with >75% improvement in their lesion. In Group C, out of 35 patients, 80% ( n = 30) patients showed very good response. Adverse drug reactions of mild to moderate intensity related to terbinafine were seen in 57 patients. Our survey indicates that terbinafine in a dose of 500 mg given once daily was efficacious and safe in the treatment of patients with dermatophytosis.

The relationship between household income and dietary intakes of 1-10 year old urban Malaysian.

Science.gov (United States)

Mohd Shariff, Zalilah; Lin, Khor Geok; Sariman, Sarina; Lee, Huang Soo; Siew, Chin Yit; Mohd Yusof, Barakatun Nisak; Mun, Chan Yoke; Mohamad, Maznorila

2015-06-01

Diet plays an important role in growth and development of children. However, dietary intakes of children living in either rural or urban areas can be influenced by household income. This cross-sectional study examined energy, nutrient and food group intakes of 749 urban children (1-10 years old) by household income status. Children's dietary intakes were obtained using food recall and record for two days. Diet adequacy was assessed based on recommended intakes of energy and nutrients and food group servings. For toddlers, all nutrients except dietary fiber (5.5 g) exceeded recommended intakes. Among older children (preschoolers and school children), calcium (548 mg, 435 mg) and dietary fiber (7.4 g, 9.4 g) did not meet recommendations while percentage of energy from total fat and saturated fats exceeded 30% and 10%, respectively. The mean sodium intakes of preschoolers (1,684 mg) and school children (2,000 mg) were relatively high. Toddlers in all income groups had similar energy and nutrient intakes and percentages meeting the recommended intakes. However, low income older children had lowest intakes of energy (P diets, particularly for older children. Parents and caregivers may need dietary guidance to ensure adequate quantity and quality of home food supply and foster healthy eating habits in children.

Structural, morphological and optical investigations on BaMgAl10O17:Eu2+ elaborated by a microwave induced solution combustion synthesis

International Nuclear Information System (INIS)

Pradal, Nathalie; Potdevin, Audrey; Chadeyron, Genevieve; Mahiou, Rachid

2011-01-01

Graphical abstract: Graphical abstract (with Research highlights). This is a paragraph for graphical abstract. Research highlights: → Synthesis of BAM:Eu 2+ by MISCS using different fuel to oxidizer molar ratios. → Both blue and red phosphors were obtained. → Majority of blue phosphors was obtained for fuel-rich synthesis. → A specific morphology was observed for each contribution. -- Abstract: Blue-emitting Eu 2+ -doped barium magnesium aluminate (BaMgAl 10 O 17 :Eu 2+ ) for advanced displays and lighting devices was prepared by a microwave induced solution combustion synthesis using urea as combustion fuel and nitrates as oxidizer. Purity control of as-synthesized blue phosphor particles was undertaken by modifying the fuel to oxidizer molar ratio. X-ray diffraction, scanning electron microscopy and photoluminescence were used to investigate powders crystallinity, particles size, morphology and luminescent properties, respectively. Fuel-rich urea reactions preferentially lead to pure phases compared to the powders synthesized with a stoichiometric fuel to oxidizer ratio. In both cases, we produce a nearly pure well-crystallized and nanostructured BaMgAl 10 O 17 :Eu 2+ . Photoluminescence measurements exhibit the characteristic blue emission of Eu 2+ under UV light excitation however a weak red emission associated to Eu 3+ is also detected.

Ubiquinol-10 supplementation improves autonomic nervous function and cognitive function in chronic fatigue syndrome.

Science.gov (United States)

Fukuda, Sanae; Nojima, Junzo; Kajimoto, Osami; Yamaguti, Kouzi; Nakatomi, Yasuhito; Kuratsune, Hirohiko; Watanabe, Yasuyoshi

2016-07-08

The aim of this study was to evaluate the benefit of oral ubiquinol-10 supplementation in CFS patients using an open-label study and a randomized, double-blinded, placebo-controlled (RCT) study. Twenty patients with CFS were randomly enrolled in an 8-week open-label oral ubiquinol-10 (150 mg ubiquinol-10/day) study. The patients and the attending physicians were not blinded to the supplementation. Forty-three patients with CFS were randomly assigned to receive either ubiquinol-10 (150 mg/day) or placebo every day for 12 weeks. The patients and the attending physicians were blinded to the supplementation, and a total of 31 patients (N = 17 in the ubiquinol group and 14 in the placebo group) completed the study. The beneficial effects of ubiquinol-10 were observed in the open-label study we conducted prior to the RCT. The RCT results suggest that supplementation with ubiquinol-10 for 12 weeks is effective for improving several CFS symptoms. © 2016 BioFactors, 42(4):431-440, 2016. © 2016 International Union of Biochemistry and Molecular Biology.

The inclusions of Mg-B (MgB12?) as potential pinning centres in high-pressure-high-temperature-synthesized or sintered magnesium diboride

International Nuclear Information System (INIS)

Prikhna, T A; Gawalek, W; Savchuk, Ya M; Habisreuther, T; Wendt, M; Sergienko, N V; Moshchil, V E; Nagorny, P; Schmidt, Ch; Dellith, J; Dittrich, U; Litzkendorf, D; Melnikov, V S; Sverdun, V B

2007-01-01

A systematic study of the structure and superconductive characteristics of high-pressure-high-temperature (2 GPa, 700-1000 deg. C )-synthesized and sintered MgB 2 without additions from different initial powders was performed. Among various secondary phases Mg-B inclusions with a stoichiometry close to MgB 12 were identified. With an increasing amount of these inclusions the critical current density increased. So these inclusions can be feasible pinning centres in MgB 2 . The highest j c values in zero field were 1300 kA cm -2 at 10 K, 780 kA cm -2 at 20 K and 62 kA cm -2 at 35 K and in 1 T field were 1200 kA cm -2 at 10 K, 515 kA cm -2 at 20 K and 0.1 kA cm -2 at 35 K for high-pressure-synthesized magnesium diboride and the field of irreversibility at 20 K reached 8 T. The average grain sizes calculated from x-ray examinations in materials having high j c were 15-37 nm

Effect of Mg Doping on the Photoluminescence of GaN:Mg Films by Radio-Frequency Plasma-Assisted Molecular Beam Epitaxy

International Nuclear Information System (INIS)

Sui Yan-Ping; Yu Guang-Hui

2011-01-01

We investigate undoped GaN and Mg-doped GaN grown by rf plasma-assisted molecular beam epitaxy (MBE) with different Mg concentrations by photoluminescence (PL) at low temperature, Hall-effect and XRD measurements. In the PL spectra of lightly Mg-doped GaN films, a low intensity near band edge (NBE) emission and strong donor-acceptor pair (DAP) emission with its phonon replicas are observed. As the Mg concentration is increased, the DAP and NBE bands become weaker and a red shift of these bands is observed in the PL spectra. Yellow luminescence (YL) is observed in heavily Mg-doped GaN. The x-ray diffraction is employed to study the structure of the films. Hall measurement shows that there is a maximum value (3.9 × 10 18 cm −3 ) of hole concentration with increasing Mg source temperature for compensation effect. PL spectra of undoped GaN are also studied under N-rich and Ga-rich growth conditions. Yellow luminescences of undoped Ga-rich GaN and heavily Mg-doped GaN are compared, indicating the different origins of the YL bands. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Dose requirements of alfentanil to eliminate autonomic responses during rapid-sequence induction with thiopental 4 mg/kg and rocuronium 0.6 mg/kg.

Science.gov (United States)

Abou-Arab, Mohammad H; Rostrup, Morten; Heier, Tom

2016-12-01

Opioids are integral part of anesthesia induction, but information on optimal dosing is limited. We aimed to determine doses of alfentanil needed to eliminate increases in 5 autonomic response variables (plasma concentrations of epinephrine, norepinephrine and vasopressin, arterial blood pressure [ABP], and heart rate) during rapid-sequence induction of anesthesia with thiopental 4 mg/kg and rocuronium 0.6 mg/kg. Prospective, randomized, observer-blinded, interventional clinical study. Large academic institution. Eighty-four healthy patients, aged 18 to 55 years, received 1 of 7 assessor-blinded doses of alfentanil (0, 10, 20, 30, 40, 50, and 60 μg/kg) together with thiopental 4 mg/kg and rocuronium 0.6 mg/kg, administered in rapid succession (15 seconds). Laryngoscopy was initiated 40 seconds after rocuronium, and tracheal intubation was concluded within 15 seconds thereafter. An indwelling radial artery catheter was used for hemodynamic monitoring and blood sampling. Relationships between alfentanil dose and response variables were tested with linear regression, and the influence of covariates (sex, body weight, and age) was determined. Alfentanil dose needed to prevent increases in ABP >10% above baseline with 95% probability was estimated with logistic regression. Significant relationships were determined between alfentanil dose and response variables. Clinically interesting influence of covariates was not found. Alfentanil 55 μg/kg was needed to prevent increases in ABP postintubation >10% above baseline with 95% probability. One individual needed a bolus of vasopressor postintubation. Optimal control of autonomic responses during rapid-sequence induction was achieved with clinically relevant doses of alfentanil in healthy patients anesthetized with thiopental 4 mg/kg and rocuronium 0.6 mg/kg. Copyright © 2016 Elsevier Inc. All rights reserved.

Conductivity, XRD, and FTIR studies of New Mg2+-ion-conducting solid polymer electrolytes: [PEG: Mg(CH3COO)2

International Nuclear Information System (INIS)

Polu, Anji Reddy; Kumar, Ranveer; Causin, Valerio; Neppalli, Ramesh

2011-01-01

Solid polymer electrolytes based on poly (ethylene glycol) (PEG) doped with Mg(CH 3 COO) 2 have been prepared by using the solution-casting method. The X-ray diffraction patterns of PEG with Mg(CH 3 COO) 2 salt indicated a decrease in the degree of crystallinity with increasing concentration of the salt. The complexation of Mg(CH 3 COO) 2 salt with the polymer was confirmed by using Fourier transform infrared spectroscopy (FTIR) studies. The ionic conductivity was measured for the [PEG: Mg(CH 3 COO) 2 ] system in the frequency range 50 Hz - 1 MHz. The addition of Mg salt was found to improve the ionic conductivity significantly. The 15-wt-% Mg(CH 3 COO) 2 -doped system had a maximum conductivity of 1.07 x 10 -6 S/cm at 303 K. The conductance spectrum shows two distinct regions: a dc plateau and a dispersive region. The temperature dependence of the ionic conductivity reveals the conduction mechanism to be an Arrhenius-type thermally activated process.

Anisotropic Mg Electrodeposition and Alloying with Ag-based Anodes from Non-Coordinating Mixed-Metal Borohydride Electrolytes for Mg Hybrid Batteries

International Nuclear Information System (INIS)

Wetzel, David J.; Malone, Marvin A.; Gewirth, Andrew A.; Nuzzo, Ralph G.

2017-01-01

A highly anisotropic electrodeposition was observed using the hybrid battery electrolyte Mg(BH 4 ) 2 with LiBH 4 in diglyme. At low overpotentials high aspect ratio platelet morphologies are observed with a strong fiber texture composed of a {10-10} and a {11-20} component, the first evidence of behavior of this kind in magnesium battery electrolytes. At high overpotentials the deposit aspect ratio is indistinguishable but the texture is shown to be primarily composed of a {11-20} fiber texture. The kinetic parameters relative to the relevant crystallographic faces are extracted from electron microscopy images and compared with the observed bulk rate extracted from the electrochemical data. The use of polycrystalline Ag foil substrates with little preferred orientation at the surface allowed highly polycrystalline nucleation at lower overpotentials than that of platinum, likely due to Ag alloying with Mg. Characterization using focused ion beam (FIB) cross-sections with Auger Electron Spectroscopy (AES) elemental analysis confirm that the deposits are primarily Mg although Mg‐Ag alloys of various compositions were observed. It is proposed that the orientation at slow rates of growth is due to the underlying kinetics of adatom diffusion on Mg and that higher rates diminish the phenomenon due to decreased time for adatom diffusion and instead are governed by the rates of adatom formation or more specifically the adatom vacancy formation on the different low-index planes of Mg.

Pre-emptive 8 mg dexamethasone and 120 mg etoricoxib for pain prevention after periodontal surgery: A randomised controlled clinical trial

Directory of Open Access Journals (Sweden)

Kranti Konuganti

2015-01-01

Full Text Available Several anti-inflammatory drugs have been used to reduce pain and discomfort after periodontal surgeries. This study evaluates the efficacy of using etoricoxib and dexamethasone for pain prevention after open-flap debridement surgery. In this study, 60 patients who were undergoing open flap debridment surgery were randomly assigned to receive a single dose preoperative medication 1 hour prior to surgery. The patients were divided into three groups. In Group 1, 20 patients were given placebo drug orally. In Group 2, 20 patients were given 8 mg Dexamethasone orally and in Group 3, 20 patients were given 120 mg Etoricoxib orally. Patients were instructed to complete a pain diary hourly for the first 8 hours after each surgery and three times a day on the following 3 days. The four point verbal rating scale (VRS 4 and Numerical rate scale were used to assess discomfort. Post-operative Assessment of Pain and Discomfort showed that persistent discomfort and pain were found to be more in the placebo group compared to dexamethasone and etoricoxib group. The adoption of a preemptive medication protocol using either etoricoxib or dexamethasone may be considered effective for pain and discomfort prevention after open-flap debridement surgeries.

Role of dopants in LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P detectors

International Nuclear Information System (INIS)

Mohammadi, Kh.; Moussavi Zarandi, A.; Afarideh, H.; Shahmaleki, S.

2013-01-01

In this study, electronic structure of LiF crystal doped with Mg,Cu,P impurities was studied with WIEN2k code on the basis of FPLAPW+lo method. Results show that in Mg-doped LiF composition, an electronic trap was created with impurity concentration of 1.56% and 3.125%. In this condition, the electronic trap with increasing the percentage of the impurities up to 4.687% is annihilated. It was found, that by doping of Mg and Cu or P simultaneously, a hole-trap is created in valence band. It was realized that in LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P, Cu impurity and Li atom, have a key role in creation of levels which lead to create electronic and hole traps. Mg impurity and F atom, only have a role in creation of electronic traps. In addition, P impurity has a main role in creation of the electronic and hole traps in LiF:Mg,Cu,P. The activation energy of electronic and hole trap in LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P crystalline lattice were obtained as 0.3 and 5.5 eV, 0.92 and 3.4 eV and 0.75 and 3.1 eV, respectively. - Graphical abstract: Figure (a) and (b) shows changes in electronic structure and band gap energy of LiF crystal due to presence of Mg and Cu, Mg and P ions respectively. - Highlights: • Electronic structure of LiF, LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P materials were studied with WIEN2K code. • In LiF:Mg,Cu and LiF:Mg,Cu,P, Li atom and Cu impurity have a key role in creation of levels. • F atom and Mg impurity only have a role in creation of electronic traps. • In LiF:Mg,Cu,P, P impurity has a main role in creation of electronic and hole traps

Study of superconducting properties of ferrocene-added MgB{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Sudesh; Varma, G.D. [Department of Physics, Indian Institute of Technology Roorkee (India); Das, S.; Bernhard, C. [Department of Physics, Fribourg Centre for Nanomaterials-FriMat, University of Fribourg (Switzerland); Shripathi, T. [UGC-DAE CSR, University Campus, Indore (India)

2014-07-15

In the present study, we have shown the effects of ferrocene (FeC{sub 10}H{sub 10}) addition on the superconducting properties of polycrystalline MgB{sub 2} superconductor using transport and magnetic measurements. The addition of FeC{sub 10}H{sub 10} up to 2 wt% in the MgB{sub 2} sample has shown enhanced critical current density, J{sub C} in the entire magnetic field region without affecting much the transition temperature. At 10 K, with respect to a pristine MgB{sub 2} sample, J{sub C} has improved by a factor of 6.55 at 6 T applied field for 1 wt% FeC{sub 10}H{sub 10}. An improvement in the upper critical field, H{sub C{sub 2}} and irreversibility field, H{sub irr} has also been observed up to 2 wt% addition of FeC{sub 10}H{sub 10}. The value of H{sub C{sub 2}} (0) as obtained using the Ginzburg-Landau (GL)-theory fit of the experimental data increases by almost 2 T for 2 wt% FeC{sub 10}H{sub 10}-added MgB{sub 2} as compared to the pristine samples. From X-ray photoemission spectroscopy (XPS), we observed that the Fe is present in sample in the form of ferromagnetic oxides, Fe{sub 3}O{sub 4} and γ-Fe{sub 2}O{sub 3}. These ferromagnetic inclusions provide efficient pinning centers to improve J{sub C}(H) behavior. The flux pinning mechanisms present in the FeC{sub 10}H{sub 10}-added samples are described and discussed in this paper. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Room temperature ferromagnetism in Mg-doped ZnO nanoparticles

International Nuclear Information System (INIS)

Singh, Jaspal; Vashihth, A.; Gill, Pritampal Singh; Verma, N. K.

2015-01-01

Zn 1-x Mg x O (x = 0, 0,10) nanoparticles were successfully synthesized using sol-gel method. X-ray diffraction (XRD) confirms that the synthesized nanoparticles possess wurtzite phase having hexagonal structure. Morphological analysis was carried out using transmission electron microscopy (TEM) which depicts the spherical morphology of ZnO nanoparticles. Energy dispersive spectroscopy (EDS) showed the presence of Mg in ZnO nanoparticles. Electron spin resonance (ESR) signal was found to be decreasing with increasing of Mg-doping concentration. The room temperature ferromagnetism was observed in undoped and Mg-doped ZnO nanoparticles. The increase of Mg-doping concentration resulted in decrease of saturation magnetization value which could be attributed to decrease of oxygen vacancies present in host nanoparticles

Correlation between E-cadherin-regulated cell adhesion and human osteosarcoma MG-63 cell anoikis.

Science.gov (United States)

Lin, Ding-Sheng; Cai, Le-Yi; Ding, Jian; Gao, Wei-Yang

2014-01-01

The aim of this study was to investigate the relationship between cell adhesion and anoikis evasion among human osteosarcoma cells (MG-63), and to further study the molecular mechanisms. Human osteosarcoma cells (MG-63) were assessed for apoptosis, and caspase-3, E-cadherin and β-catenin expression in EDTA and control non-EDTA groups. MG-63 cells were predominantly aggregated when in suspension, and the suspended cells were more dispersed in the EDTA group. Following culture in suspension for 24 h, 48 h, or 72 h, the rates of apoptosis were 34.88%±3.64%, 59.3%±7.22% and 78.5%±5.21% in the experimental group and 7.34%±2.13%, 14.7%±3.69%, and 21.4%±3.60% in the control group, respectively. Caspase-3 expression progressively increased and E-cadherin and β-catenin were decreased in the experimental group, whereas there was no change in the control group. MG-63 cells could avoid anoikis through cell adhesion, and E-cadherin might play a role in this process.

Inclusions, Porosity, and Fatigue of AlSi10Mg Parts Produced by Selective Laser Melting

Science.gov (United States)

Tang, Ming

Additive manufacturing (AM) has experienced remarkable growth in the past decade with applications in both rapid prototyping and rapid manufacturing for functional end-usable parts. As one of the most promising AM processes, selective laser melting (SLM) can be used to fabricate metal products line by line and layer upon layer within a powder bed system. Such process allows the building of parts with customized shapes, which brings higher design flexibility than traditional casting and wrought manufacturing. In this work, AlSi10Mg powder is chosen as the raw material for producing parts by SLM, since aluminum alloys are widely used in automotive and aerospace industries thanks to an excellent combination of low density and competitive mechanical properties. However, there remain multiple drawbacks which limit further applications of aluminum parts produced by SLM: lack of prediction of solidification microstructure, few studies on fatigue properties, and cost and time caused by the limited production rate. All these issues were studied in this work and summarized as follows: Rapid movement of the melt pool (at a speed around 1 m/s) in SLM of metal powder directly implies rapid solidification. In this research, the length scale of the as-built microstructure of parts built with the alloy AlSi10Mg was measured and compared with the well-known relationship between cell size and cooling rate. Cooling rates during solidification were estimated using the Rosenthal equation. It was found that the solidification structure is the expected cellular combination of silicon with alpha-aluminum. The dependence of the measured cell spacing on the calculated cooling rate follows the well-established relationship for aluminum alloys. The implication is that cell spacing can be manipulated by changing the heat input. Microscopy of polished sections through particles of the metal powder used to build the parts showed that the particles have a dendritic-eutectic structure; the

Levels of platinum group elements and rare-earth elements in wild mushroom species growing in Poland.

Science.gov (United States)

Mleczek, Mirosław; Niedzielski, Przemysław; Kalač, Pavel; Siwulski, Marek; Rzymski, Piotr; Gąsecka, Monika

2016-01-01

Due to limited data-describing abilities of mushrooms to accumulate platinum group elements (PGEs) and rare-earth elements (REEs), the aim of this study was to determine, by inductively coupled plasma optical emission spectrometry followed by microwave-assisted sample digestion by nitric acid, the content of these elements in 20 mushroom species (10 above ground and 10 growing on wood), mostly edible, collected near a busy trunk road. The highest content of PGEs in above-ground mushroom species was observed in Lepista gilva and Suillus bovinus fruit bodies (0.38 ± 0.05 and 0.37 ± 0.03 mg kg(-1) DW, respectively), while in mushrooms growing on wood, the highest content was observed in Pleurotus ostreatus (0.35 ± 0.04 mg kg(-1) DW). The mean content of PGEs for both these groups was 0.23 ± 0.08 and 0.26 ± 0.07 mg kg(-1) DW, respectively. The highest content of REEs in Suillus luteus and Tricholoma equestra was 5.03 ± 0.50 and 2.18 ± 0.56 mg kg(-1) DW, respectively, but within mushrooms growing on wood in Ganoderma applanatum fruiting bodies it was 4.19 ± 0.78 mg kg(-1) DW. Mean contents of REEs were 1.39 ± 1.21 and 1.61 ± 0.97 mg kg(-1) DW in above-ground species and species growing on wood, respectively. Generally, the group of mushroom species growing on wood was capable of slightly higher accumulation of both REEs and PGEs. No limits have been established for both the groups until now.

An Evaluation of Theraphy with Fluconazole 150 mg Tablets Compared to Fluconazole 150 mg Tablets Plus Dermoxen Lenitiva Cream in The Time to Reduce Simptomatology in Women with Vulvovaginal Candidiasis

Directory of Open Access Journals (Sweden)

Davide Carati

2014-06-01

Full Text Available Aim of the study. Authors investigated first of all the time to onset of first relief of symptoms. Secondary measures included the time to overall relief of symptoms and the reoccurrence rate over the first 45 days after the first visit. Methods. A randomized, open-label, parallel study evaluated 47 women with moderate to severe symptoms of Vulvo Vaginal Candidiasis (VVC. Patients were divided into two groups of treatment: group 1 followed a therapy with Fluconazole 150 mg tablets, while group 2 had a therapy based on Fluconazole 150 mg tablets coadjuvated by Dermoxen Lenitiva cream. Results. The time at which 50% of patients experienced first relief of symptoms was 24.6 hours for Group 1, while for Group 2 it was 12.4 hours (P<0.05. There were significant differences between the two groups in respect to the time of first relief of symptoms and reoccurrence of infection within 45 days of treatment. Conclusions. Combined treatment with Fluconazole 150 mg tablets and by Dermoxen Lenitiva cream provides statistically significant improvement in the time of first relief of symptoms, complete relief of symptoms and relapse time in the treatment of VVC compared to fluconazole 150 mg tablets only.

Effect of Mg/Ca ratios on microbially induced carbonate precipitation

Science.gov (United States)

Balci, Nurgul; Demirel, Cansu; Seref Sonmez, M.; Kurt, M. Ali

2016-04-01

Influence of Mg/Ca ratios on microbially induced carbonate mineralogy were investigated by series of experiments carried out under various environmental conditions (Mg/Ca ratio, temperature and salinity). Halophilic bacterial cultures used for biomineralization experiments were isolated from hypersaline Lake Acıgöl (Denizli, SW Turkey), displaying extreme water chemistry with an average pH around 8.6 (Balci eta l.,2015). Enriched bacterial culture used in the experiments consisted of Halomonas saccharevitans strain AJ275, Halomonas alimentaria strain L7B; Idiomarina sp. TBZ29, 98% Idiomarina seosensis strain CL-SP19. Biomineralization experiments were set up using above enriched culture with Mg/Ca ratios of 0.05, 1, 4 and 15 and salinity of 8% and 15% experiments at 30oC and 10oC. Additionally, long-term biomineralization experiments were set up to last for a year, for Mg/Ca=4 and Mg/Ca=15 experiments at 30oC. For each experimental condition abiotic experiments were also conducted. Solution chemistry throughout incubation was monitored for Na, K, Mg, Ca, bicarbonate, carbonate, ammonium and phosphate for a month. At the end of the experiments, precipitates were collected and morphology and mineralogy of the biominerals were investigated and results were evaluated using the software DIFFRAC.SUITE EVA. Overall the preliminary results showed chemical precipitation of calcite, halite, hydromagnesite and sylvite. Results obtained from biological experiments indicate that, low Mg/Ca ratios (0.05 and 1) favor chlorapatite precipitation, whereas higher Mg/Ca ratios favor struvite precipitation. Biomineralization of dolomite, huntite and magnesite is favorable at high Mg/Ca ratios (4 and 15), in the presence of halophilic bacteria. Moreover, results indicate that supersaturation with respect to Mg (Mg/Ca=15) combined with NaCl (15%) inhibits biomineralization and forms chemical precipitates. 15% salinity is shown to favor chemical precipitation of mineral phases more than

Efficacy and safety of tamsulosin hydrochloride 0.2 mg and combination of tamsulosin hydrochloride 0.2 mg plus solifenacin succinate 5 mg after transurethral resection of the prostate: a prospective, randomized controlled trial

Science.gov (United States)

Shin, Yu Seob; Zhang, Li Tao; You, Jae Hyung; Choi, In Sung; Zhao, Chen; Park, Jong Kwan

2016-01-01

Objective The objective of this study was to evaluate the safety and efficacy of tamsulosin hydrochloride 0.2 mg (TAM) and its combination with solifenacin succinate 5 mg (SOL) after transurethral resection of the prostate (TURP). Patients and methods The patients were randomized into three groups: TURP (group 1), TURP plus TAM (group 2), and TURP plus TAM + SOL (group 3). Patients in group 2 and group 3 received medication for 4 weeks. The primary efficacy end points were the mean change in total International Prostate Symptom Score (IPSS) and IPSS subscores. The secondary end points included quality-of-life score, Overactive Bladder Symptom Score, and short-form voiding and storage score of International Continence Society. Results In total, 37 men (31.8%) in group 1, 37 men (31.8%) in group 2, and 42 men (36.2%) in group 3 completed the study. In total IPSS, no significant improvement was seen from baseline to the end of treatment in groups 2 and 3 compared with group 1. However, in group 2, the decrement in the IPSS storage score was smaller than group 1 (P=0.02), and in group 3, the decrement in the IPSS voiding score was smaller than group 1 (P=0.05). In groups 2 and 3 compared with group 1, improvements in the quality of life score, total score of Overactive Bladder Symptom Score, and short-form voiding score and storage score of International Continence Society were not statistically significant. Conclusion Treatment with TAM and combination of TAM and SOL did not have significant additional benefits for lower urinary tract symptoms during the early recovery period after TURP. PMID:27698559

Efficacy and safety of terbinafine 500 mg once daily in patients with dermatophytosis

Directory of Open Access Journals (Sweden)

P Ravindra Babu

2017-01-01

Full Text Available Introduction: Dermatophytosis are the most common fungal infections globally. Terbinafine is considered to have good potency against dermatophytes, but resistance to terbinafine is on the rise. Objective: The objective of this study was to evaluate the efficacy and safety of terbinafine 500 mg given once daily in treatment of patients with superficial dermatophytosis. Materials and Methods: It was a retrospective questionnaire-based survey. Each doctor was given survey questionnaire booklet containing survey forms. Clinical response was graded according to the improvement in the affected lesion. Mycological cure was defined as negative microscopy under potassium hydroxide examination and a negative culture in Sabouraud's dextrose agar. Patients were divided into three groups depending on the duration of therapy, Group A – terbinafine 500 mg for 2 weeks, Group B – terbinafine 500 mg for 4 weeks, and Group C – terbinafine 500 mg for 6 weeks. Results: Total 50 doctors completed the survey involving 440 patients. In Group A, out of 194 patients, 87% (n = 169 patients showed very good response. In Group B, out of 211 patients, 92% (n = 194 of the patients showed very good response with >75% improvement in their lesion. In Group C, out of 35 patients, 80% (n = 30 patients showed very good response. Adverse drug reactions of mild to moderate intensity related to terbinafine were seen in 57 patients. Conclusion: Our survey indicates that terbinafine in a dose of 500 mg given once daily was efficacious and safe in the treatment of patients with dermatophytosis.

Preparation and Hydrogen Storage Properties of Mg-Rich Mg-Ni Ultrafine Particles

Directory of Open Access Journals (Sweden)

Jianxin Zou

2012-01-01

Full Text Available In the present work, Mg-rich Mg-Ni ultrafine powders were prepared through an arc plasma method. The phase components, microstructure, and hydrogen storage properties of the powders were carefully investigated. It is found that Mg2Ni and MgNi2 could be obtained directly from the vapor state reactions between Mg and Ni, depending on the local vapor content in the reaction chamber. A nanostructured MgH2 + Mg2NiH4 hydrogen storage composite could be generated after hydrogenation of the Mg-Ni ultrafine powders. After dehydrogenation, MgH2 and Mg2NiH4 decomposed into nanograined Mg and Mg2Ni, respectively. Thermogravimetry/differential scanning calorimetry (TG/DSC analyses showed that Mg2NiH4 phase may play a catalytic role in the dehydriding process of the hydrogenated Mg ultrafine particles.

Solubility limits in Mn–Mg ferrites system under hydrothermal conditions

Energy Technology Data Exchange (ETDEWEB)

Hemeda, O.M., E-mail: omhemeda@yahoo.co.uk [Physics Department, Faculty of Science, Tanta University, Tanta (Egypt); Mostafa, N.Y. [Chemistry Department, Faculty of Science, Suez Canal University, Ismailia 41522 (Egypt); Faculty of Science, Taif University, PO Box 888, Al-Haweiah, Taif (Saudi Arabia); Abd Elkader, O.H. [Electron Microscope and Thin Films Department, National Research Center, Dokki 12622, Cairo (Egypt); Electron Microscope Unit, Zoology Department, King Saud University, Riyadh 11451 (Saudi Arabia); Ahmed, M.A. [Physics Department, Faculty of Science, Al Azhar University, Nasr City, Cairo (Egypt)

2014-09-01

In the present investigation, we successfully synthesized a pure MnFe{sub 2}O{sub 4} ferrite by the hydrothermal method. Moreover, the effect of Mg ion content on the formation of Mn{sub 1−x}Mg{sub x}Fe{sub 2}O{sub 4} particles (with x varying from 0.1 to 1.0) was also investigated using XRD, SEM, TEM and Mossbauer Spectroscopy. Phases formed in the system Mn{sub 1−x}Mg{sub x}Fe{sub 2}O{sub 4}; 0.0≤x≤1.0 were investigated under hydrothermal conditions at 453 K.The produced phases were characterized by X-ray diffraction, Scanning, transmission microscopy and Mossbauer spectroscopy. The information of composition, cation distribution in the spinel structure and the particle size of the products were obtained. The spinel ferrites; Mn{sub 1−x}Mg{sub x}Fe{sub 2}O{sub 4} were formed in the range 0.0≤x≤0.3. However, sample with x>0.3 showed semi-crystalline magnesium hydroxide (Mg(OH){sub 2}) and hematite (Fe{sub 2}O{sub 3}) beside the ferrite phase. For x=1.0, only magnesium hydroxide and hematite are formed without any ferrites. Particles of uniform size around 10–20 nm were obtained in the spinel structure of Mn{sub 1−x}Mg{sub x}Fe{sub 2}O{sub 4} with x=0.0 and 0.1. The corresponding average crystallite size for each sample was 40.3 nm and 39.2 nm respectively. In addition, the Mossbauer spectra were analyzed into two subspectra, one for the tetrahedral A-site and the other for the octahedral B-site. The Mossbauer parameters were determined and discussed for the studied system. The cation distribution was estimated from the analysis of the Mossbauer spectra as well as the X-ray diffraction patterns. The results showed that Mg ions occupy mainly B-site while both Mn and Fe ions are distributed between A- and B-sites. - Highlights: • Mossbauer characterization of Mg–Mn ferrite prepared by hydrothermal route. • X-ray powder diffraction analysis of Mg–Mn ferrite prepared by hydrothermal route. • Solubility limit of MgMn ferrite under

High surface hole concentration p-type GaN using Mg implantation

International Nuclear Information System (INIS)

Long Tao; Yang Zhijian; Zhang Guoyi

2001-01-01

Mg ions were implanted on Mg-doped GaN grown by metalorganic chemical vapor deposition (MOCVD). The p-type GaN was achieved with high hole concentration (8.28 x 10 17 cm -3 ) conformed by Van derpauw Hall measurement after annealing at 800 degree C for 1 h. this is the first experimental report of Mg implantation on Mg-doped GaN and achieving p-type GaN with high surface hole concentration

Mg substituted apatite coating from alkali conversion of acidic calcium phosphate

Energy Technology Data Exchange (ETDEWEB)

Navarro da Rocha, Daniel, E-mail: dnr.navarro@gmail.com [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil); Cruz, Leila Rosa de Oliveira [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil); Campos, José Brant de [Rio de Janeiro State University - UERJ, Rio de Janeiro, R.J. (Brazil); Marçal, Rubens L. Santana Blazutti [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil); Mijares, Dindo Q.; Coelho, Paulo G. [Department of Biomaterials and Biomimetics, New York University College of Dentistry (NYU), New York, NY (United States); Prado da Silva, Marcelo H. [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil)

2017-01-01

In this work, two solutions were developed: the first, rich in Ca{sup 2+}, PO{sub 4}{sup 3−} ions and the second, rich in Ca{sup 2+}, PO{sub 4}{sup 3−} and Mg{sup 2+}, defined as Mg-modified precursor solution. For each Mg-modified precursor solution, the concentrations of Mg{sup 2+} ions were progressively increased by 5%, 10% and 15%wt. The aims of this research were to investigate the influence of magnesium ions substitution in calcium phosphate coatings on titanium surface and to evaluate these coatings by bioactivity assay in McCoy culture medium. The obtained coatings were characterized by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) analysis, and the presence of Mg ions was confirmed by the inductively coupled plasma atomic emission spectroscopy (ICP) analysis. In vitro bioactivity assay in McCoy culture medium showed bioactivity after 14 days in incubation for the HA and 10% Mg-monetite coatings. The high chemical stability of Mg-HA coatings was verified by the bioactivity assays, and no bone-like apatite deposition, characteristic of bioactivity, was observed for Mg-HA coatings, for the time period used in this study. - Highlights: • The presence of Mg ions influenced the final apatite phase present in the produced coatings. • A lower efficiency in heterogeneous deposition and an exposure of Ti substrate in 5% Mg-monetite coatings was soon verified. • McCoy culture medium was effective in predicting the coatings bioactivity.

Evaluation of the repeated-dose liver micronucleus assay using N-nitrosomorpholine in young adult rats: report on collaborative study by the Collaborative Study Group for the Micronucleus Test (CSGMT)/Japanese Environmental Mutagen Society (JEMS)-Mammalian Mutagenicity Study (MMS) Group.

Science.gov (United States)

Hayashi, Aya; Kosaka, Mizuki; Kimura, Aoi; Wako, Yumi; Kawasako, Kazufumi; Hamada, Shuichi

2015-03-01

The present study was conducted to evaluate the suitability of a repeated-dose liver micronucleus (LMN) assay in young adult rats as a collaborative study by the Mammalian mutagenicity study (MMS) group. All procedures were performed in accordance with the standard protocols of the MMS Group. Six-week-old male Crl:CD(SD) rats (5 animals/group) received oral doses of the hepatocarcinogen N-nitrosomorpholine (NMOR) at 0 (control), 5, 10, and 30mg/kg/day (10mL/kg) for 14 days. Control animals received vehicle (water). Hepatocytes were collected from the liver 24h after the last dose, and the number of micronucleated hepatocytes (MNHEPs) was determined by microscopy. The number of micronucleated immature erythrocytes (MNIMEs) in the femoral bone marrow was also determined. The liver was examined using histopathologic methods after formalin fixation. The results showed statistically significant and dose-dependent increases in the number of MNHEPs in the liver at doses of 10mg/kg and greater when compared with the vehicle control. However, no significant increase was noted in the number of MNIMEs in the bone marrow at doses of up to 30mg/kg. Histopathology of the liver revealed hypertrophy and single cell necrosis of hepatocytes at doses of 5mg/kg and above. These results showed that the induction of micronuclei by NMOR was detected by the repeated-dose LMN assay, but not by the repeated-dose bone marrow micronucleus assay. Copyright © 2014 Elsevier B.V. All rights reserved.

Mg2+ in the major groove modulates B-DNA structure and dynamics.

Directory of Open Access Journals (Sweden)

Marc Guéroult

Full Text Available This study investigates the effect of Mg(2+ bound to the DNA major groove on DNA structure and dynamics. The analysis of a comprehensive dataset of B-DNA crystallographic structures shows that divalent cations are preferentially located in the DNA major groove where they interact with successive bases of (A/GpG and the phosphate group of 5'-CpA or TpG. Based on this knowledge, molecular dynamics simulations were carried out on a DNA oligomer without or with Mg(2+ close to an ApG step. These simulations showed that the hydrated Mg(2+ forms a stable intra-strand cross-link between the two purines in solution. ApG generates an electrostatic potential in the major groove that is particularly attractive for cations; its intrinsic conformation is well-adapted to the formation of water-mediated hydrogen bonds with Mg(2+. The binding of Mg(2+ modulates the behavior of the 5'-neighboring step by increasing the BII (ε-ζ>0° population of its phosphate group. Additional electrostatic interactions between the 5'-phosphate group and Mg(2+ strengthen both the DNA-cation binding and the BII character of the 5'-step. Cation binding in the major groove may therefore locally influence the DNA conformational landscape, suggesting a possible avenue for better understanding how strong DNA distortions can be stabilized in protein-DNA complexes.

Distribution of Severity of Injury/Illness Index according to ICD-10 groups

DEFF Research Database (Denmark)

Nielsen, Niels Dalsgaard; Dahl, Michael; Rostgaard-Knudsen, Martin

OBJECTIVE: In our area patients seen by the Prehospital Emergency Physician (PEP) are all classified according to the Severity of Injury/Illness Index (SIII) groups 0 to 7. This classification enables the evaluation of the optimal use of the PEP and focus on education. The PEP should only......, dispatches a PEP for major injury and severe medical conditions. For 72 months we extracted data regarding six main groups of diagnosis according to the ICD-10-system: Metabolic diseases, Diseases of the Central Nervous System (CNS), Diseases of the circulatory system, Diseases of the respiratory system...

Study on glass-forming ability and hydrogen storage properties of amorphous Mg60Ni30La10−xCox (x = 0, 4) alloys

International Nuclear Information System (INIS)

Lv, Peng; Wang, Zhong-min; Zhang, Huai-gang; Balogun, Muhammad-Sadeeq; Ji, Zi-jun; Deng, Jian-qiu; Zhou, Huai-ying

2013-01-01

Mg 60 Ni 30 La 10−x Co x (x = 0, 4) amorphous alloys were prepared by rapid solidification, using a melt-spinning technique. X-ray diffraction and differential scanning calorimetry analysis were employed to measure their microstructure, thermal stability and glass-forming ability, and hydrogen storage properties were studied by means of PCTPro2000. Based on differential scanning calorimetry results, their glass-forming ability and thermal stability were investigated by Kissinger method, Lasocka curves and atomic cluster model, respectively. The results indicate that glass-forming ability, thermal properties and hydrogen storage properties in the Mg-rich corner of Mg–Ni–La–Co system alloys were enhanced by Co substitution for La. It can be found that the smaller activation energy (ΔΕ) and frequency factor (υ 0 ), the bigger value of B (glass transition point in Lasocka curves), and higher glass-forming ability of Mg–Ni–La–Co alloys would be followed. In addition, atomic structure parameter (λ), deduced from atomic cluster model is valuable in the design of Mg–Ni–La–Co system alloys with good glass-forming ability. With an increase of Co content from 0 to 4, the hydrogen desorption capacity within 4000 s rises from 2.25 to 2.85 wt.% at 573 K. - Highlights: • Amorphous Mg 60 Ni 30 La 10−x Co x (x = 0 and 4) alloys were produced by melt spinning. • The GFA and hydrogen storage properties were enhanced by Co substitution for La. • With an increase of Co content, the hydrogen desorption capacity rises at 573 K

The role of Mg in the crystallization of monohydrocalcite

Science.gov (United States)

Rodriguez-Blanco, Juan Diego; Shaw, Samuel; Bots, Pieter; Roncal-Herrero, Teresa; Benning, Liane G.

2014-02-01

Monohydrocalcite is a member of the carbonate family which forms in Mg-rich environments at a wide range of Mg/Ca ratios Mg2+aq/Ca2+aq≥0.17stock solutions. However, its crystallite and particle size are inversely proportional to these parameters. At high supersaturations (SIMHC = 3.89) nanometer-sized single crystals of monohydrocalcite form, while at low values (SIMHC = 2.43) the process leads to low-angle branching spherulites. Many carbonates produced during biomineralization form at similar conditions to most synthetic monohydrocalcites, and thus we hypothesize that some calcite or aragonite deposits found in the geologic record that have formed at high Mg/Ca ratios could be secondary in origin and may have originally formed via a metastable monohydrocalcite intermediate. High-Mg monohydrocalcite (χMgCO3 > 0.06) consists of individual nanometer-sized crystals (500 °C (Fig. 9b). Such high-Mg monohydrocalcites are uncommon in nature, but can be synthesized in the laboratory at high initial supersaturation levels (SI > 3.25). Low-Mg monohydrocalcite (χMgCO3 bonded to Mg, so it fully dehydrates at low temperatures (150-200 °C). They have the same composition as natural monohydrocalcites reported in the literature, and can be synthesized in the laboratory at lower supersaturation levels (SI relationships. Firstly, our on-line experiment shows an increase in nanocrystal sizes during the secondary crystallization of monohydrocalcite, which is coupled with a significant decrease in χMgCO3 (from ˜0.26 to ˜0.065). This corresponds to the transition from high- to low-Mg monohydrocalcite, suggesting that the former would be metastable and rapidly transforming to the latter, possibly triggered by the removal of Mg from aqueous solution. Secondly, Davis et al. (2000) determined that the solubility of Mg-calcite (Ca1-xMgxCO3; x = 0-0.20) varies by approximately half an order of magnitude depending on the Mg content of the solid (Ksp = 10-8.0-10-8.5). A similar

Study on synthesizing Mg/Al layered double hydroxides at different pHs

Directory of Open Access Journals (Sweden)

E Otgonjargal

2014-12-01

Full Text Available Mg/Al layered double hydroxide (LDH was successfully synthesized at different pHs values. The Mg/AL LDH was well characterized by X-Ray diffraction and Fourier transform infrared analysis. The morphology of the LDH was observed using Scanning electron microscopy with energy dispersive X-ray spectroscopy. The influence of pH values on the morphology of the Mg/Al LDHs were studied. The result showed that the well-synthesized Mg/Al LDHs could be obtained when the pH value was about 10.0 at room temperature.DOI: http://doi.dx.org/10.5564/mjc.v15i0.319 Mongolian Journal of Chemistry 15 (41, 2014, p36-39

Fabrication of seven-core multi-filamentary MgB2 wires with high critical current density by an internal Mg diffusion process

International Nuclear Information System (INIS)

Togano, K; Hur, J M; Matsumoto, A; Kumakura, H

2009-01-01

We found that the reaction between a Mg core and a B powder layer in an internal Mg diffusion (IMD)-processed multi-filamentary wire can proceed rapidly even at a furnace temperature lower than the melting point of Mg (650 deg. C), resulting in the formation of a reacted layer with a fine composite structure and, hence, excellent in-field critical current properties. The multi-filamentary wire is composed of an outermost Cu-Ni sheath and seven filaments with a Ta sheath, a Mg core, and B+SiC powder filled in the space between the Ta sheath and the Mg core. Heat treatment at 645 deg. C for 1 h produced a reacted layer with dense composite structure along the inner wall of the Ta sheath and a hole at the center of each core. This reaction probably initiated from the heat generation at the B/Mg interface, resulting in a temperature rise of the Mg core and the occurrence of liquid Mg infiltration. The J c value at 4.2 K for the reacted layer exceeds 10 5 cm -2 at 9 T, which is the highest reported so far for MgB 2 wire, including powder-in-tube (PIT)-processed wires. These results indicate that the IMD process can compete in terms of practical wire fabrication with the conventional PIT process.

Re-examining the 26Mg(α ,α')26Mg reaction: Probing astrophysically important states in 26Mg

Science.gov (United States)

Adsley, P.; Brümmer, J. W.; Li, K. C. W.; Marín-Lámbarri, D. J.; Kheswa, N. Y.; Donaldson, L. M.; Neveling, R.; Papka, P.; Pellegri, L.; Pesudo, V.; Pool, L. C.; Smit, F. D.; van Zyl, J. J.

2017-11-01

Background: The 22Ne(α ,n )25Mg reaction is one of the neutron sources for the s process in massive stars. The properties of levels in 26Mg above the α -particle threshold control the strengths of the 22Ne(α ,n )25Mg and 22Ne(α ,γ )26Mg reactions. The strengths of these reactions as functions of temperature are one of the major uncertainties in the s process. Purpose: Information on the existence, spin, and parity of levels in 26Mg can assist in constraining the strengths of the 22Ne(α ,γ )26Mg and 22Ne(α ,n )25Mg reactions, and therefore in constraining s -process abundances. Methods: Inelastically scattered α particles from a 26Mg target were momentum-analyzed in the K600 magnetic spectrometer at iThemba LABS, South Africa. The differential cross sections of states were deduced from the focal-plane trajectory of the scattered α particles. Based on the differential cross sections, spin and parity assignments to states are made. Results: A newly assigned 0+ state was observed in addition to a number of other states, some of which can be associated with states observed in other experiments. Some of the deduced Jπ values of the states observed in the present study show discrepancies with those assigned in a similar experiment performed at RCNP Osaka. The reassignments and additions of the various states can strongly affect the reaction rate at low temperatures. Conclusion: The number, location, and assignment of levels in 26Mg that may contribute to the 22Ne+α reactions are not clear. Future experimental investigations of 26Mg must have an extremely good energy resolution to separate the contributions from different levels. Coincidence experiments of 26Mg provide a possible route for future investigations.

High surface hole concentration p-type GaN using Mg implantation

CERN Document Server

Long Tao; Zhang Guo Yi

2001-01-01

Mg ions were implanted on Mg-doped GaN grown by metalorganic chemical vapor deposition (MOCVD). The p-type GaN was achieved with high hole concentration (8.28 x 10 sup 1 sup 7 cm sup - sup 3) conformed by Van derpauw Hall measurement after annealing at 800 degree C for 1 h. this is the first experimental report of Mg implantation on Mg-doped GaN and achieving p-type GaN with high surface hole concentration

Thickness dependence of J_c (0) in MgB_2 films

International Nuclear Information System (INIS)

Chen, Yiling; Yang, Can; Jia, Chunyan; Feng, Qingrong; Gan, Zizhao

2016-01-01

Highlights: • A serial of MgB_2 superconducting films from 10 nm to 8 µm have been prepared. • T_c and J_c (5 K, 0 T) of films are high. • J_c (5 K, 0 T) reaches its maximum 2.3 × 10"8 A cm"−"2 for 100 nm films. • The relationship between thickness and J_c has been discussed in detail. - Abstract: MgB_2 superconducting films, whose thicknesses range from 10 nm to 8 µm, have been fabricated on SiC substrates by hybrid physical–chemical vapor deposition (HPCVD) method. It is the first time that the T_c and the J_c of MgB_2 films are studied on such a large scale. It is found that with the increasing of thickness, T_c elevates first and then keeps roughly stable except for some slight fluctuations, while J_c (5 K, 0 T) experiences a sharp increase followed by a relatively slow fall. The maximum J_c (5 K, 0 T) = 2.3 × 10"8 A cm"−"2 is obtained for 100 nm films, which is the experimental evidence for preparing high-quality MgB_2 films by HPCVD method. Thus, this work may provide guidance on choosing the suitable thickness for applications. Meanwhile, the films prepared by us cover ultrathin films, thin films and thick films, so the study on them will bring a comprehensive understanding of MgB_2 films.

Structural Properties of EB-Welded AlSi10Mg Thin-Walled Pressure Vessels Produced by AM-SLM Technology

Science.gov (United States)

Nahmany, Moshe; Stern, Adin; Aghion, Eli; Frage, Nachum

2017-10-01

Additive manufacturing of metals by selective laser melting (AM-SLM) is hampered by significant limitations in product size due to the limited dimensions of printing trays. Electron beam welding (EBW) is a well-established process that results in relatively minor metallurgical modifications in workpieces due to the ability of EBW to pass high-density energy to the related substance. The present study aims to evaluate structural properties of EB-welded AlSi10Mg thin-walled pressure vessels produced from components prepared by SLM technology. Following the EB welding process, leak and burst tests were conducted, as was fractography analysis. The welded vessels showed an acceptable holding pressure of 30 MPa, with a reasonable residual deformation up to 2.3% and a leak rate better than 1 × 10-8 std-cc s-1 helium. The failures that occurred under longitudinal stresses reflected the presence of two weak locations in the vessels, i.e., the welded joint region and the transition zone between the vessel base and wall. Fractographic analysis of the fracture surfaces of broken vessels displayed the ductile mode of the rupture, with dimples of various sizes, depending on the failure location.

Mechanical and corrosion properties of binary Mg-Dy alloys for medical applications

Energy Technology Data Exchange (ETDEWEB)

Yang Lei, E-mail: lei.yang@hzg.de [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany); Yuanding, Huang; Qiuming, Peng; Feyerabend, Frank; Kainer, Karl Ulrich; Willumeit, Regine; Hort, Norbert [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany)

2011-12-15

Microstructure, mechanical and corrosion properties of binary magnesium-dysprosium (Mg-5, 10, 15, 20 wt.% Dy) alloys were investigated for medical applications. In the as-cast condition, the distribution of Dy is quite inhomogeneous. Mg-10Dy alloy exhibits a moderate tensile and compression yield strength, and the best elongation and corrosion resistance. After T4 (solutionizing) treatment, the distribution of Dy becomes homogeneous. The tensile and compression yield strength of all Mg-Dy alloys decreases. The elongation remains unchanged, while the corrosion resistance is largely improved after T4 treatment.

Point defects and magnetic properties of neutron irradiated MgO single crystal

Directory of Open Access Journals (Sweden)

Mengxiong Cao

2017-05-01

Full Text Available (100-oriented MgO single crystals were irradiated to introduce point defects with different neutron doses ranging from 1.0×1016 to 1.0×1020 cm-2. The point defect configurations were studied with X-ray diffuse scattering and UV-Vis absorption spectra. The isointensity profiles of X-ray diffuse scattering caused by the cubic and double-force point defects in MgO were theoretically calculated based on the Huang scattering theory. The magnetic properties at different temperature were measured with superconducting quantum interference device (SQUID. The reciprocal space mappings (RSMs of irradiated MgO revealed notable diffuse scattering. The UV-Vis spectra indicated the presence of O Frenkel defects in irradiated MgO. Neutron-irradiated MgO was diamagnetic at room temperature and became ferromagnetic at low temperature due to O Frenkel defects induced by neutron-irradiation.

Development of Al-Mg-Li alloys for fusion reactor

International Nuclear Information System (INIS)

Shoji, Yoshifusa; Yoshida, Hideo; Uno, Teruo; Baba, Yoshio; Kamada, Koji.

1985-01-01

Aluminum-magnesium-lithium alloys featuring low residual induced radioactivity and high electrical resistivity have been developed for fusion reactor structural materials. The addition of lithium in aluminum and Al-Mg alloys markedly increases electrical resistivity and tensile strength of them. However the elongation of Al-Mg-Li alloys containing more than 2 mass% lithium are less than 10 %. The Al-4--5 mass%Mg-1 mass%Li alloys are optimum for fusion reactor materials, and exhibit high resistivity (86 nΩm: 20 %IACS), medium strength (300 MPa) and good formability (22 % elongation). The variation of electrical resistivity of Al-Li and Al-Mg-Li alloys in solid solution can be approximated by the Matthiessen's rule. (author)

Fabrication of sandwich-type MgB{sub 2}/Boron/MgB{sub 2} Josephson junctions with rapid annealing method

Energy Technology Data Exchange (ETDEWEB)

Zhang, Song; Wang, Xu; Ma, Junli; Cui, Ruirui; Deng, Chaoyong, E-mail: cydeng@gzu.edu.cn

2015-11-15

Sandwich-type MgB{sub 2}/Boron/MgB{sub 2} Josephson junctions were fabricated using magnetron sputtering system. The rapid-anneal process was adopted to replace traditional way of annealing, trying to solve the problem of interdiffusion and oxidation with multilayer films. The boron film was used as barrier layer to avoid the introduction of impurities and improve reproducibility of the junctions. The bottom MgB{sub 2} thin films deposited on c-plane sapphire substrate exhibits a critical temperature T{sub C} of 37.5 K and critical current density J{sub C} at 5 K of 8.7 × 10{sup 6} A cm{sup −2}. From the XRD pattern, the bottom MgB{sub 2} thin film shows c-axis orientation, whereas the top MgB{sub 2} became polycrystalline as Boron barrier layer grown thicker. Therefore, all junction samples show lower T{sub C} than single MgB{sub 2} thin film. The junctions exhibit excellent quasiparticle characteristics with ideal dependence on temperature and Boron barrier thickness. Subharmonic gap structure was appeared in conductance characteristics, which was attributed to the multiple Andreev reflections (MAR). The result demonstrates great promise of this new fabrication technology for MgB{sub 2} Josephson junction fabrication. - Highlights: • Sandwich-type MgB{sub 2}/Boron/MgB{sub 2} Josephson junctions were fabricated. • The junctions were annealed after deposition with the rapid-anneal process. • The highest critical current is 25.3 mA at 5 K and remains non-zero near 25 K. • Subharmonic gap features can be observed in the dI/dV – V curves.

The Effect of PM 10 on Ischemia- Reperfusion Induced Arrhythmias in Rats

Directory of Open Access Journals (Sweden)

Esmat Radmanesh

Full Text Available ABSTRACT Epidemiological studies show that particulate matter (PM is the principal instigator of some adverse clinical symptoms involving cardiovascular diseases. PM exposure can increase experimental infarct size and potentiate myocardial ischemia and arrhythmias in experimental MI models such as ischemia-reperfusion (I/R injury.The present study was aimed to evaluate the effects of particulate matter (PM10 on ischemia- reperfusion induced arrhythmias with emphasis on the protective role of VA as an antioxidant on them. Male Wistar rats were divided into 8 groups (n=10: Control, VAc, Sham, VA, PM1 (0.5 mg/kg, PM2 (2.5 mg/kg, PM3 group (5 mg/kg, PM3 + VA group. Within 48 hours, PM10 was instilled into trachea in two stages. Then the hearts were isolated, transferred to a Langendorff apparatus, and subjected to global ischemia (30 minutes followed by reperfusion (60 minutes. The ischemia- reperfusion induced ventricular arrhythmias were assessed according to the Lambeth conventions.In the present study,the number, incidence and duration of arrhythmiasduring30 minutes ischemia were demonstrated to be more than those in the reperfusion stage. PM exposure increased significantly the number, incidence and duration of arrhythmias in the ischemia and reperfusion duration. Vanillic acid reduced significantly the number, incidence and duration of arrhythmias during the ischemia and reperfusion period.In summary, the results of this study demonstrated that the protective and dysrhythmic effects of VA in the PM exposure rats in I/R model are probably related to its antioxidant properties.

Multi-site TBT binding skews the inhibition of oligomycin on the mitochondrial Mg-ATPase in Mytilus galloprovincialis.

Science.gov (United States)

Nesci, Salvatore; Ventrella, Vittoria; Trombetti, Fabiana; Pirini, Maurizio; Pagliarani, Alessandra

2011-07-01

Tributyltin (TBT), a persistent lipophilic contaminant found especially in the aquatic environment, is known to be toxic to mitochondria with the F(1)F(0)-ATPase as main target. Recently our research group pointed out that in mussel digestive gland mitochondria TBT, apart from decreasing the catalytic efficiency of Mg-ATPase activity, at concentrations ≥1.0 μM in the ATPase reaction medium lessens the enzyme inhibition promoted by the specific inhibitor oligomycin. The present work aims at casting light on the mechanisms involved in the TBT-driven enzyme desensitization to inhibitors, a poorly explored field. The mitochondrial Mg-ATPase desensitization is shown to be confined to inhibitors of transmembrane domain F(0), namely oligomycin and N,N'-dicyclohexylcarbodiimide (DCCD). Accordingly, quercetin, which binds to catalytic portion F(1), maintains its inhibitory efficiency in the presence of TBT. Among the possible mechanisms involved in the Mg-ATPase desensitization to oligomycin by ≥1.0 μM TBT concentrations, a structural detachment of the two F(1) and F(0) domains does not occur according to experimental data. On the other hand TBT covalently binds to thiol groups on the enzyme structure, which are apparently only available at TBT concentrations approaching 20 μM. TBT is able to interact with multiple sites on the enzyme structure by bonds of different nature. While electrostatic interactions with F(0) proton channel are likely to be responsible for the ATPase activity inhibition, possible changes in the redox state of thiol groups on the protein structure due to TBT binding may promote structural changes in the enzyme structure leading to the observed F(1)F(0)-ATPase oligomycin sensitivity loss. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

A submillimetre-wave SIS mixer using NbN/MgO/NbN trilayers grown epitaxially on an MgO substrate

CERN Document Server

Uzawa, Y; Saito, A; Takeda, M; Wang, Z

2002-01-01

We have designed, fabricated and tested a quasi-optical superconductor-insulator-superconductor (SIS) mixer employing distributed NbN/MgO/NbN tunnel junctions and NbN/MgO/NbN microstriplines at submillimetre-wave frequencies. These trilayers were fabricated by dc- and rf-magnetron sputtering on an MgO substrate at ambient temperature so that the NbN and MgO films were grown epitaxially. Our SIS mixer consists of an MgO hyperhemispherical lens with an antireflection cap and a self-complementary log-periodic antenna made of a single-crystal NbN film, on which the distributed SIS junctions and the two-section impedance transformers were mirror-symmetrically placed at the feed point of the antenna. As designed, the junctions are 0.6 mu m wide and 15.5 mu m long, which is sufficient to absorb the incoming signal along this lossy transmission line, assuming a current density of 10 kA cm sup - sup 2. The mixer showed good I-V characteristics, with subgap-to-normal resistance ratios of about 13, although weak-link br...

Catalytically Enhanced Hydrogen Sorption in Mg-MgH2 by Coupling Vanadium-Based Catalyst and Carbon Nanotubes

Directory of Open Access Journals (Sweden)

Atikah Kadri

2015-06-01

Full Text Available Mg (MgH2-based composites, using carbon nanotubes (CNTs and pre-synthesized vanadium-based complex (VCat as the catalysts, were prepared by high-energy ball milling technique. The synergistic effect of coupling CNTs and VCat in MgH2 was observed for an ultra-fast absorption rate of 6.50 wt. % of hydrogen per minute and 6.50 wt. % of hydrogen release in 10 min at 200 °C and 300 °C, respectively. The temperature programmed desorption (TPD results reveal that coupling VCat and CNTs reduces both peak and onset temperatures by more than 60 °C and 114 °C, respectively. In addition, the presence of both VCat and CNTs reduces the enthalpy and entropy of desorption of about 7 kJ/mol H2 and 11 J/mol H2·K, respectively, as compared to those of the commercial MgH2, which ascribe to the decrease of desorption temperature. From the study of the effect of CNTs milling time, it is shown that partially destroyed CNTs (shorter milling time are better to enhance the hydrogen sorption performance.

Microstructural and mechanical properties of Al-Mg/Al{sub 2}O{sub 3} nanocomposite prepared by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Safari, J., E-mail: safari.jam@gmail.com [Department of Material Science and Engineering, Shahid Bahonar University of Kerman, P.O. Box No. 76135-133, Kerman (Iran, Islamic Republic of); Akbari, G.H. [Department of Material Science and Engineering, Shahid Bahonar University of Kerman, P.O. Box No. 76135-133, Kerman (Iran, Islamic Republic of); Research Center for Mineral Industries, Shahid Bahonar University of Kerman, P.O. Box No. 76135-133, Kerman (Iran, Islamic Republic of); Shahbazkhan, A. [Islamic Azad University, Saveh Branch, Saveh (Iran, Islamic Republic of); Delshad Chermahini, M. [Materials and Energy Research Center, Karaj (Iran, Islamic Republic of)

2011-09-29

Highlights: > The presence of Mg has remarkable effects on crystallite size and lattice strain. > The solution of Mg in the Al matrix accelerates the mechanical milling stages. > The microhardness increased in the presence of Mg. > The presence of Mg has significant effect on lattice parameter. > Steady-state situation was occurred in presence of Mg. - Abstract: The effect of milling time on the microstructure and mechanical properties of Al and Al-10 wt.% Mg matrix nanocomposites reinforced with 5 wt.% Al{sub 2}O{sub 3} during mechanical alloying was investigated. Steady-state situation was occurred in Al-10Mg/5Al{sub 2}O{sub 3} nanocomposite after 20 h, due to solution of Mg into Al matrix, while the situation was not observed in Al/5Al{sub 2}O{sub 3} nanocomposite at the same time. For the binary Al-Mg matrix, after 10 h, the predominant phase was an Al-Mg solid solution with an average crystallite size 34 nm. Up to 10 h, the lattice strain increased to about 0.4 and 0.66% for Al and Al-Mg matrix, respectively. The increasing of lattice parameter due to dissolution of Mg atom into Al lattice during milling was significant. By milling for 10 h the dramatic increase in microhardness (155 HV) for Al-Mg matrix nanocomposite was caused by grain refinement and solid solution formation. From 10 to 20 h, slower rate of increasing in microhardness may be attributed to the completion of alloying process, and dynamic and static recovery of powders.

Structural and transport properties of Sn-Mg alloys

International Nuclear Information System (INIS)

Meydaneri, F.; Saatci, E.; Oezdemir, M.; Ari, M.; Durmus, S.

2010-01-01

The structural and temperature dependence transport of Sn-Mg alloys have been investigated for five different samples (Pure Sn, Sn-1.0 wt % Mg , Sn-2.0 wt % Mg , Sn-6.0 wt.% Mg and Pure Mg). Scanning Electron Microscopy (SEM), x-ray diffraction (XRD) and Energy Dispersive x-ray Analysis (EDX) measurements were carried out in order to clarify the structural properties of the samples. It has been found that, the samples have tetragonal crystal symmetry except the pure Mg which has hexagonal crystal symmetry. The cell parameters decrease slightly with addition of Mg element. The SEM micrographs of the samples show that, the samples have smooth surfaces with clear grain boundary. There is no crack, porosity or defects on the surfaces. The electrical resistivity of the samples increases almost linearly with the increasing temperature, which were measured by four-point probe technique. The thermal conductivity values are in between 0.60-1.00 W/Km, which are decrease slightly with temperature and increase with composition of Mg. The thermal conductivity values of the alloys are in between the values of the pure samples. Thermal conductivity results of the alloys have been compared with available other studies and a good agreement has been seen between the results. In addition, the temperature coefficients of electrical resistivity and thermal conductivity have been determined, which are independent with the compositions of alloying elements

The comparison of the effects of standard 20 mg atorvastatin daily and 20 mg atorvastatin every other day on serum LDL-cholesterol and high sensitive C-reactive protein levels.

Science.gov (United States)

Keleş, Telat; Akar Bayram, Nihal; Kayhan, Tuğba; Canbay, Alper; Sahin, Deniz; Durmaz, Tahir; Ozdemir, Ozcan; Aydoğdu, Sinan; Diker, Erdem

2008-12-01

In this study, we aimed at comparing the effects of standard once daily 20 mg atorvastatin treatment with that of atorvastatin 20 mg administered every other day on serum lipids and high sensitive C-reactive protein (hs-CRP) levels. Sixty-one patients with serum total cholesterol levels of above 200 mg/dl and low density lipoprotein (LDL)--cholesterol levels of above 130 mg/dl were included in this prospective, randomized study. The patients were randomized into daily treatment of 20 mg atorvastatin (standard treatment) and 20 mg atorvastatin every other day (every other day treatment) groups. Before the treatment and at each visit, serum lipids and hs-CRP levels of all the patients were measured. Statistical analyses were performed Chi-square, unpaired t and two-way repeated measurements ANOVA tests. In the every other day treatment group, there was a 36.1% reduction in LDL-cholesterol levels by the end of first month (p0.05). The LDL cholesterol levels of the group receiving 20 mg atorvastatin every day was reduced by %41 by the end of 1 month (pevery other day, there was a 21% decrease in hs-CRP levels compared to the basal measurements at the end of first month (pevery day the decrease in hs-CRP levels at the end of one month was more striking (37%, p0.05). Alternate-day dosing of atorvastatin causes a significant lipid-lowering and antiinflammatory effects similar to that of daily administration and yet may provide some cost savings.

Blockade of group II metabotropic glutamate receptors produces hyper-locomotion in cocaine pre-exposed rats by interactions with dopamine receptors.

Science.gov (United States)

Yoon, Hyung Shin; Jang, Ju Kyong; Kim, Jeong-Hoon

2008-09-01

It was previously reported that blockade of group II metabotropic glutamate receptors (mGluRs) produces hyper-locomotion in rats previously exposed to amphetamine, indicating that group II mGluRs are well positioned to modulate the expression of behavioral sensitization by amphetamine. The present study further examined the locomotor activating effects of specific blockade of these receptors after cocaine pre-exposures. First, rats were pre-exposed to seven daily injections of cocaine (15mg/kg, IP). When challenged the next day with an injection of either saline or the group II mGluR antagonist LY341495 (0.5, 1.0 or 2.5mg/kg, IP), they produced hyper-locomotor activity, measured by infrared beam interruptions, to LY341495 compared to saline in a dose-dependent manner. Second, rats were pre-exposed to either saline or seven daily injections of cocaine (15mg/kg, IP). Three weeks later, when they were challenged with an injection of either saline or LY341495 (1.0mg/kg, IP), only rats pre-exposed to cocaine produced hyper-locomotor activity to LY341495 compared to saline. These effects, however, were not present when dopamine D1 (SCH23390; 5 or 10microg/kg), but not D2 (eticlopride; 10 or 50microg/kg), receptor antagonist was pre-injected, indicating that this cocaine-induced hyper-locomotor activity to LY341495 may be mediated in dopamine D1 receptor-dependent manner. These results suggest that group II mGluRs may be adapted to interact with dopaminergic neuronal signaling in mediating the sensitized locomotor activity produced by repeated cocaine pre-exposures.

Optical absorption and thermoluminescence in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature; Absorcion optica y termoluminiscencia en MgO, MgO:Ni y MgO:Li irradiados a temperatura ambiente

Energy Technology Data Exchange (ETDEWEB)

Delgado, L

1984-07-01

Optical absorption and thermoluminescence (TL) studies in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature are presented. In pure Mg O the thermal annihilation of Fe3+ by recombination with thermally released electrons at {approx} 90 and 175 degree centigree and the V center annealing by hole release up to 100 degree centigree cause the observed glow peaks at these temperatures. The TL excitation spectrum shows two maxima at 245 nm (electron center) and 288 nm (Fe3+). In Mg O:Ni X irradiation induces Fe{sup 2}+ {yields}- Fe{sup 3}+ and Ni{sup 2}+ {yields} Ni{sup 3}+ oxidations. Two TL emission bands centered at 110 degree centigree (red) and 80 o{sup C} (green) are assigned to electron release and their recombination at Fe{sup 3}+ and Ni{sup 3}+ respectively. In Mg O:Li two TL emission bands, one blue (430 nm) and the other red (730 nm) with excitation maxima at 245 nm (electron center) and 200 nm (hole center) respectively are observed. No V-center formation was detected in both Ni and Li doped samples. (Author) 42 refs.

Development of Ti-sheathed MgB2 wires with high critical current density

International Nuclear Information System (INIS)

Liang, G; Fang, H; Hanna, M; Yen, F; Lv, B; Alessandrini, M; Keith, S; Hoyt, C; Tang, Z; Salama, K

2006-01-01

Working towards developing lightweight superconducting magnets for future space and other applications, we have successfully fabricated mono-core Ti-sheathed MgB 2 wires by the powder-in-tube method. The wires were characterized by magnetization, electrical resistivity, x-ray diffraction, scanning electron microscopy, and energy dispersive spectrometry measurements. The results indicate that the Ti sheath does not react with the magnesium and boron, and the present wire rolling process can produce MgB 2 wires with a superconducting volume fraction of at least 64% in the core. Using the Bean model, it was found that at 5 K, the magnetic critical current densities, J c , measured in magnetic fields of 0, 5, and 8 T are about 4.2 x 10 5 , 3.6 x 10 4 , and 1.4 x 10 4 A cm -2 , respectively. At 20 K and 0 T, the magnetic J c is about 2.4 x 10 5 A cm -2 . These results show that at zero and low fields, the values of the magnetic J c for Ti-sheathed MgB 2 wires are comparable with the best results available for the Fe-sheathed MgB 2 wires. At high fields, however, the J c for Ti-sheathed MgB 2 wires appears higher than that for the Fe-sheathed MgB 2 wires

Comparison of 1 mg and 2 mg overnight dexamethasone suppression tests for the screening of Cushing's syndrome in obese patients.

Science.gov (United States)

Sahin, Mustafa; Kebapcilar, Levent; Taslipinar, Abdullah; Azal, Omer; Ozgurtas, Taner; Corakci, Ahmet; Akgul, Emin Ozgur; Taslipinar, Mine Yavuz; Yazici, Mahmut; Kutlu, Mustafa

2009-01-01

Obesity is currently a major public health problem and one of the potential underlying causes of obesity in a minority of patients is Cushing's syndrome (CS). Traditionally, the gold standard screening test for CS is 1 mg dexamethasone overnight suppression test. However, it is known that obese subjects have high false positive results with this test. We have therefore compared the 1 mg and 2 mg overnight dexamethasone suppression tests in obese subjects. Patients whose serum cortisol after ODST was >50 nM underwent and a low-dose dexamethasone suppression test (LDDST); 24-hour urine cortisol was collected for basal urinary free cortisol (UFC). For positive results after overnight 1-mg dexamethasone suppression test we also performed the overnight 2-mg dexamethasone suppression test. We prospectively evaluated 100 patients (22 men and 78 women, ranging in age from 17 to 73 years with a body mass index (BMI) >30 kg/m2 who had been referred to our hospital-affiliated endocrine clinic because of simple obesity. Suppression of serum cortisol to suppression. Thyroid function tests, lipid profiles, homocysteine, antithyroglobulin, anti-thyroid peroxidase antibody levels, vitamin B12, folate levels, insulin resistance [by homeostasis model assessment (HOMA)] and 1.0 mg postdexamethasone (postdex) suppression cortisol levels were measured. We found an 8% false-positive rate in 1 mg overnight test and 2% in 2 mg overnight test (p=0.001). There was no correlation between the cortisol levels after ODST and other parameters. Our results indicate that the 2 mg overnight dexamethasone suppression test (ODST) is more convenient and accurate than 1-mg ODST as a screening test for excluding CS in subjects with simple obesity.

Structure and Mechanical Properties of the AlSi10Mg Alloy Samples Manufactured by Selective Laser Melting

Science.gov (United States)

Li, Xiaodan; Ni, Jiaqiang; Zhu, Qingfeng; Su, Hang; Cui, Jianzhong; Zhang, Yifei; Li, Jianzhong

2017-11-01

The AlSi10Mg alloy samples with the size of 14×14×91mm were produced by the selective laser melting (SLM) method in different building direction. The structures and the properties at -70°C of the sample in different direction were investigated. The results show that the structure in different building direction shows different morphology. The fish scale structures distribute on the side along the building direction, and the oval structures distribute on the side vertical to the building direction. Some pores in with the maximum size of 100 μm exist of the structure. And there is no major influence for the build orientation on the tensile properties. The tensile strength and the elongation of the sample in the building direction are 340 Mpa and 11.2 % respectively. And the tensile strength and the elongation of the sample vertical to building direction are 350 Mpa and 13.4 % respectively

Mg2BIV: Narrow Bandgap Thermoelectric Semiconductors

Science.gov (United States)

Kim, Il-Ho

2018-05-01

Thermoelectric materials can convert thermal energy directly into electric energy and vice versa. The electricity generation from waste heat via thermoelectric devices can be considered as a new energy source. For instance, automotive exhaust gas and all industrial processes generate an enormous amount of waste heat that can be converted to electricity by using thermoelectric devices. Magnesium compound Mg2BIV (BIV = Si, Ge or Sn) has a favorable combination of physical and chemical properties and can be a good base for the development of new efficient thermoelectrics. Because they possess similar properties to those of group BIV elemental semiconductors, they have been recognized as good candidates for thermoelectric applications. Mg2Si, Mg2Ge and Mg2Sn with an antifluorite structure are narrow bandgap semiconductors with indirect band gaps of 0.77 eV, 0.74 eV, and 0.35 eV, respectively. Mg2BIV has been recognized as a promising material for thermoelectric energy conversion at temperatures ranging from 500 K to 800 K. Compared to other thermoelectric materials operating in the similar temperature range, such as PbTe and filled skutterudites, the important aspects of Mg2BIV are non-toxic and earth-abundant elements. Based on classical thermoelectric theory, the material factor β ( m* / m e)3/2μκ L -1 can be utilized as the criterion for thermoelectric material selection, where m* is the density-of-states effective mass, me is the mass of an electron, μ is the carrier mobility, and κL is the lattice thermal conductivity. The β for magnesium silicides is 14, which is very high compared to 0.8 for iron silicides, 1.4 for manganese silicides, and 2.6 for silicon-germanium alloys. In this paper, basic phenomena of thermoelectricity and transport parameters for thermoelectric materials were briefly introduced, and thermoelectric properties of Mg2BIV synthesized by using a solid-state reaction were reviewed. In addition, various Mg2BIV compounds were discussed

Coenzyme Q10 Supplementation and Oocyte Aneuploidy in Women Undergoing IVF-ICSI Treatment

Directory of Open Access Journals (Sweden)

Yaakov Bentov

2014-01-01

Full Text Available Background The age-related reduction in live-birth rate is attributed to a high rate of aneuploidy and follicle depletion. We showed in an animal model that treatment with Coenzyme Q10 (CoQ10 markedly improved reproductive outcome. The aim of this study was to compare the post-meiotic oocyte aneuploidy rate in in vitro fertilization (IVF and intra cytoplasmic sperm injection (ICSI patients treated with CoQ10 or placebo. Methods We conducted a double blind placebo controlled randomized trial that included IVF-ICSI patients 35-43 years of age. The patients were treated with either 600 mg of CoQ10 or an equivalent number of placebo caps. We compared the post-meiotic aneuploidy rate using polar body biopsy (PBBX and comparative genomic hybridization (CGH. According to the power calculation, 27 patients were needed for each arm. Results Owing to safety concerns regarding the effects of polar body biopsy on embryo quality and implantation, the study was terminated before reaching the target number of participants. A total of 39 patients were evaluated and randomized (17 CoQ10, 22 placebo, 27 were given the study medication (12 CoQ10, 15 placebo, and 24 completed an IVF-ICSI cycle including PBBX and embryo transfer (10 CoQ10, 14 placebo. Average age, base line follicle stimulating hormone (FSH, peak estradiol and progesterone serum level, as well as the total number of human menopausal gonadotropin (hMG units–-did not differ between the groups. The rate of aneuploidy was 46.5% in the CoQ10 group compared to 62.8% in the control. Clinical pregnancy rate was 33% for the CoQ10 group and 26.7% for the control group. Conclusion No significant differences in outcome were detected between the CoQ10 and placebo groups. However, the final study was underpowered to detect a difference in the rate of aneuploidy.

Tensile Properties Characterization of AlSi10Mg Parts Produced by Direct Metal Laser Sintering via Nested Effects Modeling.

Science.gov (United States)

Palumbo, Biagio; Del Re, Francesco; Martorelli, Massimo; Lanzotti, Antonio; Corrado, Pasquale

2017-02-08

A statistical approach for the characterization of Additive Manufacturing (AM) processes is presented in this paper. Design of Experiments (DOE) and ANalysis of VAriance (ANOVA), both based on Nested Effects Modeling (NEM) technique, are adopted to assess the effect of different laser exposure strategies on physical and mechanical properties of AlSi10Mg parts produced by Direct Metal Laser Sintering (DMLS). Due to the wide industrial interest in AM technologies in many different fields, it is extremely important to ensure high parts performances and productivity. For this aim, the present paper focuses on the evaluation of tensile properties of specimens built with different laser exposure strategies. Two optimal laser parameters settings, in terms of both process quality (part performances) and productivity (part build rate), are identified.

Preparation, characterization and gas permeation study of PSf/MgO nanocomposite membrane

Directory of Open Access Journals (Sweden)

S. M. Momeni

2013-09-01

Full Text Available Nanocomposite membranes composed of polymer and inorganic nanoparticles are a novel method to enhance gas separation performance. In this study, membranes were fabricated from polysulfone (PSf containing magnesium oxide (MgO nanoparticles and gas permeation properties of the resulting membranes were investigated. Membranes were prepared by solution blending and phase inversion methods. Morphology of the membranes, void formations, MgO distribution and aggregates were observed by SEM analysis. Furthermore, thermal stability, residual solvent in the membrane film and structural ruination of membranes were analyzed by thermal gravimetric analysis (TGA. The effects of MgO nanoparticles on the glass transition temperature (Tg of the prepared nanocomposites were studied by differential scanning calorimetry (DSC. The Tg of nanocomposite membranes increased with MgO loading. Fourier transform infrared (FTIR spectra of nanocomposite membranes were analyzed to identify the variations of the bonds. The results obtained from gas permeation experiments with a constant pressure setup showed that adding MgO nanoparticles to the polymeric membrane structure increased the permeability of the membranes. At 30 wt% MgO loading, the CO2 permeability was enhanced from 25.75×10-16 to 47.12×10-16 mol.m/(m².s.Pa and the CO2/CH4 selectivity decreased from 30.84 to 25.65 when compared with pure PSf. For H2, the permeability was enhanced from 44.05×10-16 to 67.3×10-16 mol.m/(m².s.Pa, whereas the H2/N2 selectivity decreased from 47.11 to 33.58.

Modeling and stabilities of Mg/MgH2 interfaces: A first-principles investigation

Directory of Open Access Journals (Sweden)

Jia-Jun Tang

2014-07-01

Full Text Available We have theoretically investigated the modeling and the structural stabilities of various Mg/MgH2 interfaces, i.e. Mg(101¯0/MgH2(210, Mg(0001/MgH2(101 and Mg(101¯0/MgH2(101, and provided illuminating insights into Mg/MgH2 interface. Specifically, the main factors, which impact the interfacial energies, are fully considered, including surface energies of two phases, mutual lattice constants of interface model, and relative position of two phases. The surface energies of Mg and MgH2, on the one hand, are found to be greatly impacting the interfacial energies, reflected by the lowest interfacial energy of Mg(0001/MgH2(101 which is comprised of two lowest energy surfaces. On the other hand, it is demonstrated that the mutual lattice constants and the relative position of two phases lead to variations of interfacial energies, thus influencing the interface stabilities dramatically. Moreover, the Mg-H bonding at interface is found to be the determinant of Mg/MgH2 interface stability. Lastly, interfacial and strain effects on defect formations are also studied, both of which are highly facilitating the defect formations. Our results provide a detailed insight into Mg/MgH2 interface structures and the corresponding stabilities.

Frovatriptan 2.5 mg plus dexketoprofen (25 mg or 37.5 mg) in menstrually related migraine. Subanalysis from a double-blind, randomized trial.

Science.gov (United States)

Allais, G; Bussone, G; Tullo, V; Cortelli, P; Valguarnera, F; Barbanti, P; Sette, G; D'Onofrio, F; Curone, M; Benedetto, C

2015-01-01

The purpose of this article is to investigate the efficacy and safety of frovatriptan plus dexketoprofen 25 or 37.5 mg (FroDex25 or FroDex37.5, respectively) compared to that of frovatriptan 2.5 mg (Frova) in menstrually related migraine (MRM). The aim of this article is to analyze a subgroup of 76 women who treated an MRM attack in this multicenter, randomized, double-blind, parallel-group study. The primary end-point was the proportion of patients who were pain free (PF) at two hours. Secondary end-points included pain-relief (PR) at two hours and 48 hours sustained pain free (SPF). PF rates at two hours were 29% under Frova, 48% under FroDex25 and 64% under FroDex37.5 (p dexketoprofen produced higher PF rates at two hours compared to Frova while maintaining efficacy at 48 hours. Tolerability profiles were comparable. © International Headache Society 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

A study on toxicity of gasoline and GM-10 on liver of mice and it's amelioration by black tea extract.

Science.gov (United States)

Verma, Ramtej Jayram; Dave, Manjeet; Mathuria, Neeta

2008-01-01

The aim of present study is to investigate the ameliorative effect of black tea extract on gasoline and GM-10 induced toxicity in liver of mice. Eighty healthy male mice weighing 38-40 g approximately were divided into eight groups which included untreated control and various treated groups. Mice were treated with Gasoline 462 mg/kg/day and GM-10 low dose (206 mg/kg/day) and high dose (412 mg/kg/day) subcutaneously for 30 days. Black tea extract was given as 2 g/100 mL drinking water (2% w/v) instead of pure drinking water. All the animals were sacrificed on 31st day by cervical dislocation and livers were isolated and weighed. Parameters such as lipid peroxidation, catalase, superoxide dismutase, glutathione peroxidase, glutathione and total ascorbic acid were studied. The results revealed dose-dependent toxicity of gasoline and GM-10 on liver. Administration of black tea extract ameliorates this toxicity of gasoline and GM-10 in liver of mice. This proves the effective ameliorative effect of black tea extract.

Improvement of the Reaction Rates of Mg with H{sub 2} by the Addition of TaF{sub 5} via Reactive Mechanical Grinding

Energy Technology Data Exchange (ETDEWEB)

Song, Myoung Youp [Chonbuk National University, Jeonju (Korea, Republic of); Kwak, Young Jun; Lee, Seong Ho [Chonbuk National University, Jeonju (Korea, Republic of); Park, Hye Ryoung [Chonnam National University, Gwangju (Korea, Republic of)

2014-02-15

A sample with a composition of 90 wt% Mg-10 wt% TaF{sub 5} (named Mg-10TaF{sub 5}) was prepared by reactive mechanical grinding, and its hydriding and dehydriding properties were examined. The activation of Mg-10TaF{sub 5} was not required. At n=1, the sample absorbed 3.63 wt% H for 5 min, 4.03 wt% H for 10 min, and 4.53 wt% H for 30 min at 593 K under 12 bar H2. At n=1, the sample desorbed 0.59 wt% H for 5 min, 1.46 wt% H for 10 min, 3.42 wt% H for 30 min, and 4.24 wt% H for 60 min at 593 K under 1.0 bar H2. Mg-10TaF{sub 5} after reactive mechanical grinding contained MgH{sub 2}, Mg, and very small amounts of MgF{sub 2} and Ta{sub 2}H. The XRD pattern of Mg-10TaF{sub 5} dehydrided at n=3 revealed Mg, MgH{sub 2}, a small amount of MgO, and very small amounts of MgF{sub 2} and Ta{sub 2}H phases. Mg-10Fe{sub 2}O{sub 3} and Mg-10MnO were reported to have quite high hydriding rate and dehydriding rates, respectively. Mg-10TaF{sub 5} had a larger initial hydriding rate but a lower quantity of hydrogen absorbed for 60 min than Mg-10Fe{sub 2}O{sub 3}. However, Mg-10TaF{sub 5} had a higher initial dehydriding rate (after the incubation period) and a larger quantity of hydrogen desorbed for 60 min than Mg-10MnO.

What is the Right Temperature Sensitivity for Foraminiferal Mg/ca Paleothermometry in Ancient Oceans?

Science.gov (United States)

Eggins, S.; Holland, K.; Hoenisch, B.; Spero, H. J.; Allen, K. A.

2013-12-01

Mg/Ca seawater thermometry has become a cornerstone of modern paleoceanography. Laboratory experiments, seafloor core-top samples, plankton trap and tow collected materials all indicate consistent temperature sensitivity (9-10% increase in Mg/Ca per °C) for a full range of modern planktic foraminifer species. While these results demonstrate the overall robustness of Mg/Ca paleothermometry for the modern ocean, it is an empirical tool for which there is limited understanding of its bio-physio-chemical basis and its applicability to ancient oceans. We have undertaken experimental cultures of Orbulina universa, Globigerinoides sacculifer and Globigerinoides ruber (pink) across a range of seawater compositions (temperature, carbonate chemistry and Mg/Casw) that encompass modern and ancient Paleogene and Cretaceous ocean compositions (Mg/Casw 0.25x to 2x modern and pCO2 = 200 to 1500 ppmv). Our results reveal that the sensitivity of the Mg/Ca-thermometer for planktic foraminifers reduces significantly with Mg/Casw, rather than remaining constant as has been widely assumed or, increasing at lower Mg/Casw as proposed recently by Evans and Müller (2012). These results indicate that the modern sensitivity of 9-10% increase in Mg/Ca per °C cannot yet be applied to obtain reliable relative temperature change estimates to ancient oceans. These results further suggest that variations in foraminiferal Mg/Ca compositions in ancient oceans with lower Mg/Casw may correspond to larger temperature variations than in the modern ocean. Evans D. and Müller W., Paleoceanography, vol. 27, PA4205, doi:10.1029/2012PA002315, 2012

Transformation of Mg-bearing amorphous calcium carbonate to Mg-calcite - In situ monitoring

Science.gov (United States)

Purgstaller, Bettina; Mavromatis, Vasileios; Immenhauser, Adrian; Dietzel, Martin

2016-02-01

The formation of Mg-bearing calcite via an amorphous precursor is a poorly understood process that is of relevance for biogenic and abiogenic carbonate precipitation. In order to gain an improved insight on the controls of Mg incorporation in calcite formed via an Mg-rich amorphous calcium carbonate (Mg-ACC) precursor, the precipitation of Mg-ACC and its transformation to Mg-calcite was monitored by in situ Raman spectroscopy. The experiments were performed at 25.0 ± 0.03 °C and pH 8.3 ± 0.1 and revealed two distinct pathways of Mg-calcite formation: (i) At initial aqueous Mg/Ca molar ratios ⩽ 1:6, Mg-calcite formation occurs via direct precipitation from solution. (ii) Conversely, at higher initial Mg/Ca molar ratios, Mg-calcite forms via an intermediate Mg-rich ACC phase. In the latter case, the final product is a calcite with up to 20 mol% Mg. This Mg content is significant higher than that of the Mg-rich ACC precursor phase. Thus, a strong net uptake of Mg ions from the solution into the crystalline precipitate throughout and also subsequent to ACC transformation is postulated. Moreover, the temporal evolution of the geochemical composition of the reactive solution and the Mg-ACC has no significant effect on the obtained ;solubility product; of Mg-ACC. The enrichment of Mg in calcite throughout and subsequent to Mg-ACC transformation is likely affected by the high aqueous Mg/Ca ratio and carbonate alkalinity concentrations in the reactive solution. The experimental results have a bearing on the formation mechanism of Mg-rich calcites in marine early diagenetic environments, where high carbonate alkalinity concentrations are the rule rather than the exception, and on the insufficiently investigated inorganic component of biomineralisation pathways in many calcite secreting organisms.

Different flavonoids present in the micronized purified flavonoid fraction (Daflon 500 mg) contribute to its anti-hyperpermeability effect in the hamster cheek pouch microcirculation.

Science.gov (United States)

Paysant, J; Sansilvestri-Morel, P; Bouskela, E; Verbeuren, T J

2008-02-01

This study evaluated microcirculatory effects of the flavonoid substances that constitute the micronized purified flavonoid fraction (MPFF) (Daflon 500 mg) in comparison to diosmin. In groups of 3 male hamsters, oral treatment with MPFF or diosmin (15 min before anesthesia) did not alter blood pressure. At 10 or 30 mg/kg, both MPFF and diosmin significantly decreased the leaky sites caused by ischemia/reperfusion (I/R) (30 min) in the hamster cheek pouch; the effect was significantly higher with MPFF (39+/-1% and 52+/-1%, respectively) than diosmin (18+/-1% and 37+/-3%, respectively). Eight groups of 3 hamsters each were treated with the components of MPFF. Diosmetin only decreased the number leaky sites at 30 mg/kg (decrease: 15+/-2%). The decrement at 10 and 30 mg/kg averaged at: 17+/-3% and 44+/-1%, respectively, for hesperidin; 19+/-1% and 46+/-2%, respectively, for linarin; and 30+/-1% and 44+/-1%, respectively, for isorhoifolin. Hesperidin, linarin, and isorhoifolin each displayed an anti-leakage effect comparable to or greater than diosmin. MPFF decreases permeability more than any of its single constituents, suggesting that the flavonoids present in its formulation have a synergistic action. These results illustrate that MPFF is more potent than single diosmin in this model of hyperpermeability and that each of the flavonoid substances present in MPFF contribute to its action.

Enhanced hydrogen storage properties of MgH2 co-catalyzed with K2NiF6 and CNTs.

Science.gov (United States)

Sulaiman, N N; Ismail, M

2016-12-06

The composite of MgH 2 /K 2 NiF 6 /carbon nanotubes (CNTs) is prepared by ball milling, and its hydrogenation properties are studied for the first time. MgH 2 co-catalyzed with K 2 NiF 6 and CNTs exhibited an improvement in the onset dehydrogenation temperature and isothermal de/rehydrogenation kinetics compared with the MgH 2 -K 2 NiF 6 composite. The onset dehydrogenation temperature of MgH 2 doped with 10 wt% K 2 NiF 6 and 5 wt% CNTs is 245 °C, which demonstrated a reduction of 25 °C compared with the MgH 2 + 10 wt% K 2 NiF 6 composite. In terms of rehydrogenation kinetics, MgH 2 doped with 10 wt% K 2 NiF 6 and 5 wt% CNTs samples absorbed 3.4 wt% of hydrogen in 1 min at 320 °C, whereas the MgH 2 + 10 wt% K 2 NiF 6 sample absorbed 2.6 wt% of hydrogen under the same conditions. For dehydrogenation kinetics at 320 °C, the MgH 2 + 10 wt% K 2 NiF 6 + 5 wt% CNTs sample released 3.3 wt% hydrogen after 5 min of dehydrogenation. By contrast, MgH 2 doped with 10 wt% K 2 NiF 6 released 3.0 wt% hydrogen in the same time period. The apparent activation energy, E a , for the dehydrogenation of MgH 2 doped with 10 wt% K 2 NiF 6 reduced from 100.0 kJ mol -1 to 70.0 kJ mol -1 after MgH 2 was co-doped with 10 wt% K 2 NiF 6 and 5 wt% CNTs. Based on the experimental results, the hydrogen storage properties of the MgH 2 /K 2 NiF 6 /CNTs composite is enhanced because of the catalytic effects of the active species of KF, KH and Mg 2 Ni that are formed in situ during dehydrogenation, as well as the unique structure of CNTs.

The protocols for the 10/66 dementia research group population-based research programme

OpenAIRE

Salas Aquiles; Rodriguez Juan; McKeigue Paul; Jacob KS; Krishnamoorthy ES; Huang Yueqin; Guerra Mariella; Gavrilova Svetlana I; Dewey Michael; Arizaga Raul; Albanese Emiliano; Acosta Daisy; Ferri Cleusa P; Prince Martin; Sosa Ana

2007-01-01

Abstract Background Latin America, China and India are experiencing unprecedentedly rapid demographic ageing with an increasing number of people with dementia. The 10/66 Dementia Research Group's title refers to the 66% of people with dementia that live in developing countries and the less than one tenth of population-based research carried out in those settings. This paper describes the protocols for the 10/66 population-based and intervention studies that aim to redress this imbalance. Meth...

Microstructure and bonding mechanism of Al/Ti bonded joint using Al-10Si-1Mg filler metal

International Nuclear Information System (INIS)

Sohn, Woong H.; Bong, Ha H.; Hong, Soon H.

2003-01-01

The microstructures and liquid state diffusion bonding mechanism of cp-Ti to 1050 Al using an Al-10.0wt.%Si-1.0wt.%Mg filler metal with 100 μm in thickness have been investigated at 620 deg. C under 1x10 -4 Torr. The effects of bonding process parameters on microstructure of bonded joint have been analyzed by using an optical microscope, AES, scanning electron microscopy and EDS. The interfacial bond strength of Al/Ti bonded joints was measured by the single lap shear test. The results show that the bonding at the interface between Al and filler metal proceeds by wetting the Al with molten filler metal, and followed by removal of oxide layer on surface of Al. The interface between Al and filler metal moved during the isothermal solidification of filler metal by the diffusion of Si from filler metal into Al layer. The interface between Al and filler metal became curved in shape with increasing bonding time due to capillary force at grain boundaries. The bonding at the interface between Ti and filler metal proceeds by the formation of two different intermetallic compound layers, identified as Al 5 Si 12 Ti 7 and Al 12 Si 3 Ti 5 , followed by the growth of the intermetallic compound layers. The interfacial bond strength at Al/Ti joint increased with increasing bonding time up to 25 min at 620 deg. C. However, the interfacial bond strength of Al/Ti joint decreased after bonding time of 25 min at 620 deg. C due to formation of cavities in Al near Al/intermetallic interfaces

Low-temperature atomic layer deposition of MgO thin films on Si

International Nuclear Information System (INIS)

Vangelista, S; Mantovan, R; Lamperti, A; Tallarida, G; Kutrzeba-Kotowska, B; Spiga, S; Fanciulli, M

2013-01-01

Magnesium oxide (MgO) films have been grown by atomic layer deposition in the wide deposition temperature window of 80–350 °C by using bis(cyclopentadienyl)magnesium and H 2 O precursors. MgO thin films are deposited on both HF-last Si(1 0 0) and SiO 2 /Si substrates at a constant growth rate of ∼0.12 nm cycle −1 . The structural, morphological and chemical properties of the synthesized MgO thin films are investigated by x-ray reflectivity, grazing incidence x-ray diffraction, time-of-flight secondary ion mass spectrometry and atomic force microscopy measurements. MgO layers are characterized by sharp interface with the substrate and limited surface roughness, besides good chemical uniformity and polycrystalline structure for thickness above 7 nm. C–V measurements performed on Al/MgO/Si MOS capacitors, with MgO in the 4.6–11 nm thickness range, allow determining a dielectric constant (κ) ∼ 11. Co layers are grown by chemical vapour deposition in direct contact with MgO without vacuum-break (base pressure 10 −5 –10 −6  Pa). The as-grown Co/MgO stacks show sharp interfaces and no elements interdiffusion among layers. C–V and I–V measurements have been conducted on Co/MgO/Si MOS capacitors. The dielectric properties of MgO are not influenced by the further process of Co deposition. (paper)

Pharmacokinetics, Safety and Cognitive Function Profile of Rupatadine 10, 20 and 40 mg in Healthy Japanese Subjects: A Randomised Placebo-Controlled Trial.

Directory of Open Access Journals (Sweden)

Jörg Täubel

Full Text Available Rupatadine is a marketed second generation antihistamine, with anti-PAF activity, indicated for symptomatic treatment of allergic rhinitis and urticaria. This study was conducted to evaluate the pharmacokinetics (PK, pharmacodynamics (PD, safety and tolerability of rupatadine in healthy Japanese subjects after single and multiple oral doses.In this randomised, double-blind, placebo-controlled study, 27 male and female healthy Japanese subjects were administered single and multiple escalating rupatadine dose of 10, 20 and 40 mg or placebo. Blood samples were collected at different time points for PK measurements and subjects were assessed for safety and tolerability. The effect of rupatadine on cognitive functioning was evaluated by means of computerized cognitive tests: rapid visual information processing (RVP, reaction time (RT, spatial working memory (SWM and visual analogue scales (VAS.Exposure to rupatadine as measured by Cmax and AUC was found to increase in a dose dependent manner over the dose range of 10-40 mg for both single and multiple dose administration. The safety assessments showed that all treatment related side effects were of mild intensity and there were no serious adverse events (SAEs or withdrawals due to treatment-emergent adverse events (TEAEs in this study. The therapeutic dose of rupatadine did not show any CNS impairment in any of the cognitive tests.This study demonstrated that rupatadine is safe and well tolerated by Japanese healthy subjects. The PK-PD profile confirmed previous experience with rupatadine.

The precipitation process in Mg-Ca-(Zn) alloys investigated by positron annihilation spectroscopy

International Nuclear Information System (INIS)

Ortega, Yanicet; Monge, Miguel Angel; Pareja, Ramiro

2008-01-01

Coincidence doppler broadening (CDB) spectroscopy has been applied to study the precipitation process induced by aging in Mg-1.0 wt.% Ca and Mg-1.0 wt.% Ca-1.0 wt.% Zn alloys. In addition positron lifetime experiments and microhardness measurements have been performed. A peak centered at ∼11.5 x 10 -3 m 0 c is found in the CDB ratio spectra of the alloys aged at 473 K. It is attributed to annihilations with the core electrons of Ca. The results indicate the formation of a particle dispersion that hardens the alloys. This dispersion is correlated with the appearance of the peak attributed to Ca atoms. Zn atoms in the Mg matrix inhibit the formation of quenched-in vacancies bound to Ca atoms in the aged ternary alloy producing the dispersion refinement

Anisotropic thermal expansion of MgSiN2 from 10 to 300 K as measured by neutron diffraction

NARCIS (Netherlands)

Bruls, R.J.; Hintzen, H.T.J.M.; Metselaar, R.; Loong, C.K.

2000-01-01

The lattice parameters of orthorhombic MgSiN2 as a function of the temperature have been determined from time-of-flight neutron powder diffraction. The results indicate that MgSiN2, just like several other adamantine-type crystals, exhibits a relatively small thermal expansion coefficient at low

Stress corrosion inhibitors for type 18-10 stainless steels with low carbon content in hot and concentrated solutions of MgCl2. Study of some inorganic iodides

International Nuclear Information System (INIS)

Pinard, J.-L.

1974-01-01

Stress corrosion inhibitors for type Z2CN18-10 austenitic stainless steels with low carbon content in a solution of Cl 2 Mg at 105 deg C were investigated. It was established that iodides are the most adequate corrosion inhibitors because they react simultaneously upon the three main components of the alloy (Fe, Ni, Cr). A difference of behavior between I 2 Mg and the other iodides was observed (in electrochemistry and in simple stress corrosion experiments) and the influence of the metallic cation associated to I - was studied. The formation of the superficial film and the phenomena liable to occur at the interface film-corrosive solution were examined: film growth in MgCl 2 ; influence of certain substances added to the solution. A mechanism of inhibition by I - is suggested. It is similar to the mechanism proposed by BERGEN for the stress corrosion cracking by Cl - [fr

The efficacy and safety of fixed-dose combination of amlodipine/benazepril in Chinese essential hypertensive patients not adequately controlled with benazepril monotherapy: a multicenter, randomized, double-blind, double-dummy, parallel-group clinical trial.

Science.gov (United States)

Yan, Pingping; Fan, Weihu

2014-01-01

This double-blind, double-dummy clinical trial evaluated the efficacy and safety of two strengths of fixed-dose combination of amlodipine/benazepril in Chinese hypertensive patients not adequately controlled with benazepril. Of 442 patients who received treatment with benazepril 10 mg for 4 weeks, 341 patients failed to achieve to diastolic blood pressure (DBP) benazepril 2.5/10 mg, or amlodipine/benazepril 5/10 mg, or benazepril 10 mg for 8 weeks. BP reductions with amodipinel/benazepril 2.5/10 mg (15.2/11.8 mmHg) or amlodipine/benazepril 5/10 mg (15.4/12.4 mmHg) were significantly greater than that with benazepril 10 mg (9.88/9.46 mmHg) at study end (p benazepril). BP control rate was 83.8% with amlodipine/benazepril 2.5/10 mg, 80.2% with amlodipine/benazepril 5/10 mg, 64.9% with benazepril 10 mg at study end (p benazepril). Three groups were generally well tolerated. Our study indicated that amlodipine/benazepril fixed-dose combination offered significant additional BP reductions and BP control rate compared with the continuation of benazepril monotherapy. No significant differences were observed in both BP reductions and BP control rate between amlodipine/benazepril 2.5/10 mg and amlodipine/benazepril 5/10 mg.

Mg Incorporation Efficiency in Pulsed MOCVD of N-Polar GaN:Mg

Science.gov (United States)

Marini, Jonathan; Mahaboob, Isra; Hogan, Kasey; Novak, Steve; Bell, L. D.; Shahedipour-Sandvik, F.

2017-10-01

We report on the effect of growth polarity and pulsed or δ -doped growth mode on impurity incorporation in metalorganic chemical vapor deposition-grown GaN. In Ga-polar orientation, up to 12× enhancement in Mg concentration for given Mg flow rate is observed, resulting in enhanced p-type conductivity for these samples. In contrast, this enhancement effect is greatly diminished for N-polar samples, falling off with increasing Mg flow and showing maximum enhancement of 2.7× at 30 nmol/min Mg flow. At higher Mg flow rates, Mg incorporation at normal levels did not correspond to p-type conductivity, which may be due to Mg incorporation at nonacceptor sites. Concentrations of C, O, and Si were also investigated, revealing dependence on Mg flow in N-polar pulsed samples. Carbon incorporation was found to decrease with increasing Mg flow, and oxygen incorporation was found to remain high across varied Mg flow. These effects combine to result in N-polar samples that are not p-type when using the pulsed growth mode.

Recovery of SO2 and MgO from By-Products of MgO Wet Flue Gas Desulfurization.

Science.gov (United States)

Yan, Liyun; Lu, Xiaofeng; Wang, Quanhai; Guo, Qiang

2014-11-01

An industrial demonstration unit using natural gas as a heat source was built to calcine the by-products of MgO wet flue gas desulfurization from power plants; influencing factors on the SO 2 content in calciner gas were comprehensively analyzed; and an advantageous recycling condition of MgO and SO 2 from by-products was summarized. Results showed that the SO 2 content in the calciner gas was increased by more than 10 times under a lower excess air coefficient, a higher feed rate, a lower crystal water in by-products, and a higher feed port position. For the tests conducted under the excess air coefficient above and below one, the effect of the furnace temperature on the SO 2 content in the calciner gas was reversed. Results of activity analysis indicate that particles of MgO generated under the calcination temperature of 900-1,000°C had a high activity. In contrast, due to the slight sintering, MgO generated under the calcination temperature of 1,100°C had a low activity. To recycle SO 2 as well as MgO, a temperature range of 900-927°C for TE103 is proposed. These studies will prompt the desulfurization market diversification, reduce the sulfur's dependence on imports for making sulfuric acid, be meaningful to balance the usage of the natural resource in China, and be regarded as a reference for the development of this technology for other similar developing countries.

In-situ synchrotron x-ray study of MgB2 formation when doped by SiC

Science.gov (United States)

Abrahamsen, A. B.; Grivel, J.-C.; Andersen, N. H.; Herrmann, M.; Häßler, W.; Birajdar, B.; Eibl, O.; Saksl, K.

2008-02-01

We have studied the evolution of the reaction xMg + 2B + ySiC → zMg1-p(B1-qCq)2 + yMg2Si in samples of 1, 2, 5 and 10 wt% SiC doping. We found a coincident formation of MgB2 and Mg2Si, whereas the crystalline part of the SiC nano particles is not reacting at all. Evidence for incorporation of carbon into the MgB2 phase was established from the decrease of the a-axis lattice parameter upon increasing SiC doping. An estimate of the MgB2 lower limit grain size was found to decrease from L100 = 795 Å and L002 = 337 Å at 1 wt% SiC to L100 = 227 Å and L002= 60 Å at 10 wt% SiC. Thus superconductivity might be suppressed at 10 wt% SiC doping due to the grain size approaching the coherence length.

Optical and magnetic resonance studies of Mg-doped GaN homoepitaxial layers grown by molecular beam epitaxy

International Nuclear Information System (INIS)

Glaser, E.R.; Murthy, M.; Freitas, J.A.; Storm, D.F.; Zhou, L.; Smith, D.J.

2007-01-01

Low-temperature photoluminescence (PL) and optically detected magnetic resonance (ODMR) at 24 GHz have been performed on a series of MBE-grown Mg-doped (10 17 -10 20 cm -3 ) GaN homoepitaxial layers. High-resolution PL at 5 K revealed intense bandedge emission with narrow linewidths (0.2-0.4 meV) attributed to annihilation of excitons bound to shallow Mg acceptors. In contrast to many previous reports for GaN heteroepitaxial layers doped with [Mg]>3x10 18 cm -3 , the only visible PL observed was strong shallow donor-shallow acceptor recombination with zero phonon line at 3.27 eV. Most notably, ODMR on this emission from a sample doped with [Mg] of 1x10 17 cm -3 revealed the first evidence for the highly anisotropic g-tensor (g parallel ∼2.19, g perpendicular ∼0) expected for Mg shallow acceptors in wurtzite GaN. This result is attributed to the much reduced dislocation densities (≤5x10 6 cm -3 ) and Mg impurity concentrations compared to those characteristic of the more conventional investigated Mg-doped GaN heteroepitaxial layers

Depth-dependent and surface damages in MgAl sub 2 O sub 4 and MgO irradiated with energetic iodine ions

CERN Document Server

Aruga, T; Ohmichi, T; Okayasu, S; Kazumata, Y; Jitsukawa, S

2002-01-01

Samples of polycrystalline ceramics of MgAl sub 2 O sub 4 irradiated at the ambient temperature with 85 MeV I sup 7 sup + iodine ions to doses up to 1x10 sup 1 sup 9 m sup - sup 2 is observed to be amorphized up to depths around 6 mu m from the ion-incident surface for a dose of 1.2x10 sup 1 sup 9 m sup - sup 2 , through a cross-sectional transmission electron microscopy. A step height of 1 mu m is formed across the border between the masked and irradiated regions of the surface. The height of the step is observed to increase sharply from the irradiated area towards the edge at the border, forming a peak as tall as 1.5 mu m. A glossy, silver-gray film with a thickness less than 0.1 mu m is unexpectedly observed to have formed on the surface of samples of MgAl sub 2 O sub 4 and MgO, in about 3.5 years aging after the irradiation to 1.2x10 sup 1 sup 9 m sup - sup 2 , being left untouched in the air. The film is easily peeled off along grain boundaries and found to be amorphous from the electron diffraction patt...

Towards 31Mg-β-NMR resonance linewidths adequate for applications in magnesium chemistry

DEFF Research Database (Denmark)

Stachura, M.; McFadden, R. M. L.; Chatzichristos, A.

2017-01-01

The span of most chemical shifts recorded in conventional 25Mg-NMR spectroscopy is ~ 100 ppm. Accordingly, linewidths of ~ 10 ppm or better are desirable to achieve adequate resolution for applications in chemistry. Here we present first high-field 31Mg- β-NMR measurements of 31Mg+ ions implanted...

Molecular beam epitaxy of iodine-doped CdTe and (CdMg)Te

Energy Technology Data Exchange (ETDEWEB)

Fischer, F.; Waag, A.; Litz, Th.; Scholl, S.; Schmitt, M.; Landwehr, G. (Physikalisches Inst. der Univ. Wuerzburg (Germany)); Bilger, G. (Zentrum fuer Sonnenenergie und Wasserstofforschung, Stuttgart (Germany))

1994-08-01

The n-type doping of CdTe and (CdMg)Te by the use of the solid dopant source material ZnI[sub 2] is reported. Doping levels as high as 7x10[sup 18] cm[sup -3] have been obtained in CdTe with carrier mobilities around 500 cm[sup 2]/V[center dot]s at room temperature. For a dopant incorporation higher than 1x10[sup 19] cm[sup -3] the free carrier concentration decreases, indicating the onset of a compensation mechanism, which is observed in the case of chlorine and bromine doping, too. Preliminary experiments show that with increasing Mg concentration the free carrier concentration decreases. Nevertheless, CdMgTe with a magnesium concentration x=0.37 (band gap 2.2 eV at room temperature) can be doped up to 2x10[sup 17] cm[sup -3]. The existence of deep donor levels in this CdTe based ternary is not supposed to be the only reason for the reduction of the free carrier concentration. For high Mg support during molecular beam epitaxial (MBE) growth of wide gap (CdMg)Te layers, the ZnI[sub 2] incorporation is reduced, leading to low doping levels, too

Ab initio molecular dynamics simulation of the liquid and amorphous structure of Mg65Cu25Gd10 alloy

International Nuclear Information System (INIS)

Gao, R.; Zhao, Y.F.; Liu, X.J.; Liu, Z.K.; Hui, X.

2013-01-01

The liquid and amorphous structures of Mg 65 Cu 25 Gd 10 alloy were studied by using molecular dynamics methods within the frame of density functional theory. The generalized and partial pair correlation functions, structure factors, coordination numbers and bond pairs for this alloy were analyzed. It is shown that this alloy exhibit typical characterization of liquid structure at the temperature higher than 750 K, and of amorphous structure with shoulders on the second diffuse peaks of the pair correlation functions curves at room temperature. The local short and medium range ordering tends to be increased with the decrease of temperature. Both the liquid and the amorphous structures are mainly composed of icosahedral type of bond pairs. Perfect and distorted icosahedra can be differentiated from the atomic configuration of the amorphous alloy

Tensile Properties Characterization of AlSi10Mg Parts Produced by Direct Metal Laser Sintering via Nested Effects Modeling

Directory of Open Access Journals (Sweden)

Biagio Palumbo

2017-02-01

Full Text Available A statistical approach for the characterization of Additive Manufacturing (AM processes is presented in this paper. Design of Experiments (DOE and ANalysis of VAriance (ANOVA, both based on Nested Effects Modeling (NEM technique, are adopted to assess the effect of different laser exposure strategies on physical and mechanical properties of AlSi10Mg parts produced by Direct Metal Laser Sintering (DMLS. Due to the wide industrial interest in AM technologies in many different fields, it is extremely important to ensure high parts performances and productivity. For this aim, the present paper focuses on the evaluation of tensile properties of specimens built with different laser exposure strategies. Two optimal laser parameters settings, in terms of both process quality (part performances and productivity (part build rate, are identified.

Garenoxacin treatment of experimental endocarditis caused by viridans group streptococci.

Science.gov (United States)

Anguita-Alonso, Paloma; Rouse, Mark S; Piper, Kerryl E; Steckelberg, James M; Patel, Robin

2006-04-01

The activity of garenoxacin was compared to that of levofloxacin or penicillin in a rabbit model of Streptococcus mitis group (penicillin MIC, 0.125 microg/ml) and Streptococcus sanguinis group (penicillin MIC, 0.25 microg/ml) endocarditis. Garenoxacin and levofloxacin had MICs of 0.125 and 0.5 microg/ml, respectively, for both study isolates. Rabbits with catheter-induced aortic valve endocarditis were given no treatment, penicillin at 1.2x10(6) IU/8 h intramuscularly, garenoxacin at 20 mg/kg of body weight/12 h intravenously, or levofloxacin at 40 mg/kg/12 h intravenously. For both isolates tested, garenoxacin area under the curve (AUC)/MIC and maximum concentration of drug in serum (Cmax)/MIC ratios were 368 and 91, respectively. Rabbits were sacrificed after 3 days of treatment; cardiac valve vegetations were aseptically removed and quantitatively cultured. For S. mitis group experimental endocarditis, all studied antimicrobial agents were more active than no treatment (PS. sanguinis group endocarditis, no studied antimicrobial agents were more active than no treatment. We conclude that AUC/MIC and Cmax/MIC ratios may not predict activity of some quinolones in experimental viridans group endocarditis and that garenoxacin and levofloxacin may not be ideal choices for serious infections caused by some quinolone-susceptible viridans group streptococci.

In vitro degradation and cytotoxicity of Mg/Ca composites produced by powder metallurgy.

Science.gov (United States)

Zheng, Y F; Gu, X N; Xi, Y L; Chai, D L

2010-05-01

Mg/Ca (1 wt.%, 5 wt.%, 10 wt.% Ca) composites were prepared from pure magnesium and calcium powders using the powder metallurgy method, aiming to enlarge the addition of Ca content without the formation of Mg(2)Ca. The microstructures, mechanical properties and cytotoxicities of Mg/Ca composite samples were investigated. The corrosion of Mg/Ca composites in Dulbecco's modified Eagle's medium (DMEM) for various immersion intervals was studied by electrochemical impedance spectroscopy measurements and environmental scanning electron microscope, with the concentrations of released Mg and Ca ions in DMEM for various immersion time intervals being measured. It was shown that the main constitutional phases were Mg and Ca, which were uniformly distributed in the Mg matrix. The ultimate tensile strength (UTS) and elongation of experimental composites decreased with increasing Ca content, and the UTS of Mg/1Ca composite was comparable with that of as-extruded Mg-1Ca alloy. The corrosion potential increased with increasing Ca content, whereas the current density and the impedance decreased. It was found that the protective surface film formed quickly at the initial immersion stage. With increasing immersion time, the surface film became compact, and the corrosion rate of Mg/Ca composites slowed down. The surface film consisted mainly of CaCO(3), MgCO(3)x3H(2)O, HA and Mg(OH)(2) after 72 h immersion in DMEM. Mg/1Ca and Mg/5Ca composite extracts had no significant toxicity (p>0.05) to L-929 cells, whereas Mg/10Ca composite extract induced approximately 40% reduced cell viability. Copyright (c) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Impact of interface manipulation of oxide on electrical transport properties and low-frequency noise in MgO/NiFe/MgO heterojunctions

International Nuclear Information System (INIS)

Li, Jian-wei; Zhao, Chong-jun; Feng, Chun; Yu, Guang-hua; Zhou, Zhongfu

2015-01-01

Low-frequency noise and magnetoresistance in sputtered-deposited Ta(5 nm)/MgO (3 nm)/NiFe(10 nm)/MgO(3 nm)/Ta(3 nm) films have been measured as a function of different annealing times at 400°C. These measurements did not change synchronously with annealing time. A significant increase in magnetoresistance is observed for short annealing times (of the order of minutes) and is correlated with a relatively small reduction in 1/f noise. In contrast, a significant reduction in 1/f noise is observed for long annealing times (of the order of hours) accompanied by a small change in magnetoresistance. After annealing for 2 hours, the 1/f noise decreases by three orders of magnitude. Transmission electron microscopy and slow positron annihilation results implicate the cause being micro-structural changes in the MgO layers and interfaces following different annealing times. The internal vacancies in the MgO layers gather into vacancy clusters to reduce the defect density after short annealing times, whereas the MgO/NiFe and the NiFe/MgO interfaces improve significantly after long annealing times with the amorphous MgO layers gradually crystallizing following the release of interfacial stress

Impact of interface manipulation of oxide on electrical transport properties and low-frequency noise in MgO/NiFe/MgO heterojunctions

Science.gov (United States)

Li, Jian-wei; Zhao, Chong-jun; Feng, Chun; Zhou, Zhongfu; Yu, Guang-hua

2015-08-01

Low-frequency noise and magnetoresistance in sputtered-deposited Ta(5 nm)/MgO (3 nm)/NiFe(10 nm)/MgO(3 nm)/Ta(3 nm) films have been measured as a function of different annealing times at 400°C. These measurements did not change synchronously with annealing time. A significant increase in magnetoresistance is observed for short annealing times (of the order of minutes) and is correlated with a relatively small reduction in 1/f noise. In contrast, a significant reduction in 1/f noise is observed for long annealing times (of the order of hours) accompanied by a small change in magnetoresistance. After annealing for 2 hours, the 1/f noise decreases by three orders of magnitude. Transmission electron microscopy and slow positron annihilation results implicate the cause being micro-structural changes in the MgO layers and interfaces following different annealing times. The internal vacancies in the MgO layers gather into vacancy clusters to reduce the defect density after short annealing times, whereas the MgO/NiFe and the NiFe/MgO interfaces improve significantly after long annealing times with the amorphous MgO layers gradually crystallizing following the release of interfacial stress.

Impact of interface manipulation of oxide on electrical transport properties and low-frequency noise in MgO/NiFe/MgO heterojunctions

Energy Technology Data Exchange (ETDEWEB)

Li, Jian-wei [School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhao, Chong-jun; Feng, Chun; Yu, Guang-hua [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhou, Zhongfu [School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China)

2015-08-15

Low-frequency noise and magnetoresistance in sputtered-deposited Ta(5 nm)/MgO (3 nm)/NiFe(10 nm)/MgO(3 nm)/Ta(3 nm) films have been measured as a function of different annealing times at 400°C. These measurements did not change synchronously with annealing time. A significant increase in magnetoresistance is observed for short annealing times (of the order of minutes) and is correlated with a relatively small reduction in 1/f noise. In contrast, a significant reduction in 1/f noise is observed for long annealing times (of the order of hours) accompanied by a small change in magnetoresistance. After annealing for 2 hours, the 1/f noise decreases by three orders of magnitude. Transmission electron microscopy and slow positron annihilation results implicate the cause being micro-structural changes in the MgO layers and interfaces following different annealing times. The internal vacancies in the MgO layers gather into vacancy clusters to reduce the defect density after short annealing times, whereas the MgO/NiFe and the NiFe/MgO interfaces improve significantly after long annealing times with the amorphous MgO layers gradually crystallizing following the release of interfacial stress.

Verification and validation of multi-group library MUSE1.0 created from ENDF/B-VII.0

International Nuclear Information System (INIS)

Chen Yixue; Wu Jun; Yang Shouhai; Zhang Bin; Lu Daogang; Chen Chaobin

2010-01-01

A multi-group library set named MUSE1.0 with 172-neutron group and 42-photon group is produced based on ENDF/B-VII.0 using NJOY code. Weight function of the multi-group library set is taken from the Vitanim-e library and the max legendre order of scattering matrix is six. All the nuclides have thermal scattering data created using free-gas scattering law and 10 Bondarenko background cross sections se lected to generate the self-shielded multi-group cross sections. The final libraries have GENDF-format, MATXS-format and ACE-multi-group sub-libraries and each sub-library generated under 4 temperatures(293 K,600 K,800 K and 900 K). This paper provides a summary of the procedure to produce the library set and a detail description of the validation of the multi-group library set by several critical benchmark devices and shielding benchmark devices using MCNP code. The ability to handle the thermal neutron transport and resonance self-shielding problems are investigated specially. In the end, we draw the conclusion that the multi-group libraries produced is credible and can be used in the R and D process of Supercritical Water Reactor Design. (authors)

Preparation and Properties of Mg-Cu-Y-Al bulk Amorphous Alloys

DEFF Research Database (Denmark)

Pryds, Nini; Eldrup, Morten Mostgaard; Ohnuma, M.

2000-01-01

Bulk amorphous (Mg(1-gamma)Al(gamma))(60)CU(30)Y(10) alloys were prepared using a relatively simple technique of rapid cooling of the melt in a copper wedge mould. The temperature vs, time was recorded during the cooling and solidification process of the melt and compared with a spacial and tempo......Bulk amorphous (Mg(1-gamma)Al(gamma))(60)CU(30)Y(10) alloys were prepared using a relatively simple technique of rapid cooling of the melt in a copper wedge mould. The temperature vs, time was recorded during the cooling and solidification process of the melt and compared with a spacial...... temperatures in specimens containing a few percent Al. The alloy with no Al crystallises apparently without the formation of nanoparticles. The critical cooling rate for the formation of an amorphous Mg(60)CU(30)Y(10) specimen was determined experimentally by a combination of DSC data and temperature vs, time...

The precipitation process in Mg-Ca-(Zn) alloys investigated by positron annihilation spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Ortega, Yanicet [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain); Departamento de Fisica de Materiales, Facultad de Ciencias Fisicas, Universidad Complutense de Madrid, 28040 Madrid (Spain)], E-mail: yanicet@fis.ucm.es; Monge, Miguel Angel; Pareja, Ramiro [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain)

2008-09-08

Coincidence doppler broadening (CDB) spectroscopy has been applied to study the precipitation process induced by aging in Mg-1.0 wt.% Ca and Mg-1.0 wt.% Ca-1.0 wt.% Zn alloys. In addition positron lifetime experiments and microhardness measurements have been performed. A peak centered at {approx}11.5 x 10{sup -3}m{sub 0}c is found in the CDB ratio spectra of the alloys aged at 473 K. It is attributed to annihilations with the core electrons of Ca. The results indicate the formation of a particle dispersion that hardens the alloys. This dispersion is correlated with the appearance of the peak attributed to Ca atoms. Zn atoms in the Mg matrix inhibit the formation of quenched-in vacancies bound to Ca atoms in the aged ternary alloy producing the dispersion refinement.

Characterisation of a Personal TL Photon Dosemeter Based on Two LiF(Mg,Cu,P) Detectors in Terms of Hp(0.07,alpha) and Hp(10,alpha)

International Nuclear Information System (INIS)

Fantuzzi, E.; Monteventi, F.; Sermenghi, I.; Uleri, G.

1999-01-01

A study was undertaken to evaluate the response of the ENEA Photon Personal Dosemeter, slightly modified in design, in terms of H p (0.07, α) and H p (10, α). A filtration of 20 and 270 mg.cm -2 respectively for the two LiF(Mg,Cu,P) detectors employed was adopted according to a preliminary analytical simulation. The new dosemeter can measure both H p (0.07, α) with a maximum uncertainty of ±4% in the range from 10 to 200 keV and H p (10, α) with a maximum uncertainty of ±15% in the range from 10 keV to 1.25 MeV, using the detector responses together with a correction function with respect to their ratio. Moreover, tests were performed to evaluate the dosemeter angular response (0 deg., 20 deg., 40 deg., and 60 deg.) obtaining good results according to international recommendations. All irradiation tests were performed at SSL of ENEA Institute for Radiation Protection in Bologna using the ISO water phantom (30 x 30 x 15 cm 3 ) and standard ISO filtered X ray beams as well as 137 Cs and 60 Co sources. This work represents a preliminary type test of the ENEA photon personal dosemeter and allows its introduction in routine dosimetry practice in accordance with the ICRU reference quantities. (author)

Pulse laser irradiation into superconducting MgB2 detector

International Nuclear Information System (INIS)

Fujiwara, Daisuke; Miki, Shigehito; Satoh, Kazuo; Yotsuya, Tsutomu; Shimakage, Hisashi; Wang, Zhen; Okayasu, Satoru; Katagiri, Masaki; Machida, Masahiko; Kato, Masaru; Ishida, Takekazu

2005-01-01

We performed 20-ps pulse laser irradiation experiments on a MgB 2 neutron detector to know a thermal-relaxation process for designing a MgB 2 neutron detector. The membrane-type structured MgB 2 device was fabricated to minimize the heat capacity of sensing part of a detector as well as to enhance its sensitivity. We successfully observed a thermal-relaxation signal resulting from pulse laser irradiation by developing a detection circuit. The response time was faster than 1 μs, meaning that the detector would be capable of counting neutrons at a rate of more than 10 6 events per second

Loss of Endothelial Barrier in Marfan Mice (mgR/mgR Results in Severe Inflammation after Adenoviral Gene Therapy.

Directory of Open Access Journals (Sweden)

Philipp Christian Seppelt

Full Text Available Marfan syndrome is an autosomal dominant inherited disorder of connective tissue. The vascular complications of Marfan syndrome have the biggest impact on life expectancy. The aorta of Marfan patients reveals degradation of elastin layers caused by increased proteolytic activity of matrix metalloproteinases (MMPs. In this study we performed adenoviral gene transfer of human tissue inhibitor of matrix metalloproteinases-1 (hTIMP-1 in aortic grafts of fibrillin-1 deficient Marfan mice (mgR/mgR in order to reduce elastolysis.We performed heterotopic infrarenal transplantation of the thoracic aorta in female mice (n = 7 per group. Before implantation, mgR/mgR and wild-type aortas (WT, C57BL/6 were transduced ex vivo with an adenoviral vector coding for human TIMP-1 (Ad.hTIMP-1 or β-galactosidase (Ad.β-Gal. As control mgR/mgR and wild-type aortas received no gene therapy. Thirty days after surgery, overexpression of the transgene was assessed by immunohistochemistry (IHC and collagen in situ zymography. Histologic staining was performed to investigate inflammation, the neointimal index (NI, and elastin breaks. Endothelial barrier function of native not virus-exposed aortas was evaluated by perfusion of fluorescent albumin and examinations of virus-exposed tissue were performed by transmission electron microscopy (TEM.IHC and ISZ revealed sufficient expression of the transgene. Severe cellular inflammation and intima hyperplasia were seen only in adenovirus treated mgR/mgR aortas (Ad.β-Gal, Ad.hTIMP-1 NI: 0.23; 0.43, but not in native and Ad.hTIMP-1 treated WT (NI: 0.01; 0.00. Compared to native mgR/mgR and Ad.hTIMP-1 treated WT aorta, the NI is highly significant greater in Ad.hTIMP-1 transduced mgR/mgR aorta (p = 0.001; p = 0.001. As expected, untreated Marfan grafts showed significant more elastolysis compared to WT (p = 0.001. However, elastolysis in Marfan aortas was not reduced by adenoviral overexpression of hTIMP-1 (compared to untreated

Wound healing effect of bioactive ion released from Mg-smectite.

Science.gov (United States)

Sasaki, Yu; Sathi, Gulsan Ara; Yamamoto, Osamu

2017-08-01

Bioactive ions like Mg 2+ and Si 4+ have been known as promotion factors of tissue regeneration. In the present work, Mg-smectite, consisting of Mg 2+ and Si 4+ ions, was synthesized by a solution process, and evaluated for the efficiency of the powder on wound healing in rats. White precipitates were obtained by mixing a magnesium chloride hexahydrate solution and a sodium silicate hexahydrate solution at room temperature. The precipitates mixed with a NaOH aqueous solution were subjected to hydrothermal reaction, and finally crystalline Mg-smectite powder was obtained. The crystal and molecular structure of Mg-smectite was identified by X-ray diffractometry (XRD) and Fourier-transform infrared spectroscopy (FT-IR). The synthesized material was determined to be crystalline Mg-smectite. The amount of Mg 2+ and Si 4+ ions released from Mg-smectite in physiological saline was analyzed by inductively coupled plasma mass spectroscopy (ICP-MS). The total amount of Si 4+ ion released from Mg-smectite was greater than that of Mg 2+ ion. To evaluate the wound healing effect of Mg-smectite, Mg-smectite powder was applied to a full-thickness surgical wound reaching the subcutaneous tissue in the rat's abdomen. At 1 and 2weeks, skin tissue was collected and subjected to histological analysis. The results for skin regeneration showed no significant difference in wound size between the control and Mg-smectite group. However, it was found that the neovascularization, collagen deposition, and maturation were notedly accelerated by applying Mg-smectite powder in comparison with the control. Mg-smectite can then be hypothesized to stimulate the regeneration of skin tissue by releasing Mg 2+ and Si 4+ ions. These results suggested that Mg-smectite could offer great potential as a wound dressing material. Copyright © 2017 Elsevier B.V. All rights reserved.

Enantioselective disposition of omeprazole, pantoprazole, and lansoprazole in a same Brazilian subjects group.

Science.gov (United States)

Cassiano, Neila M; Oliveira, Regina V; Bernasconi, Gilberto C R; Cass, Quezia B

2012-04-01

This work reports the result of the enantioselective disposition of pantoprazole, omeprazole, and lansoprazole in a same group of Brazilian health subjects. Ten nongenotyped healthy subjects were used for this study. Each subject received a single oral dose of 80 mg of pantoprazole, 40 mg of omeprazole, and 30 mg of lansoprazole, and the plasma concentrations of the enantiomers were measured for 8 h postdose. For pantoprazole and omeprazole, among the 10 volunteers investigated, only one volunteer (Subject # 4) presented higher plasma concentrations of the (+)-enantiomer than those of (-)-enantiomer. Nevertheless, the area under the concentration-time curve of the (+)-lansoprazole was higher than those the (-)-lansoprazole for all subjects. The comparison of proton pump inhibitors' enantiomers disposition from a single group volunteer demonstrated that pantoprazole and omeprazole can be used to differentiate extensive from poor CYP2C19 metabolizer while lansoprazole cannot do it. Copyright © 2011 Wiley Periodicals, Inc.

Improved CO_2 adsorption capacity and cyclic stability of CaO sorbents incorporated with MgO

International Nuclear Information System (INIS)

Farah Diana Mohd Daud; Kumaravel Vignesh; Srimala Sreekantan; Abdul Rahman Mohamed

2016-01-01

Calcium oxide (CaO) sorbents incorporated with magnesium oxide (MgO) were synthesized using a co-precipitation route. The sorbents were prepared with different MgO concentrations (from 5 wt% to 30 wt%). The as-prepared sorbents were characterized using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX) and BET surface area analysis techniques. The sintering effect of CaO sorbents was decreased after the incorporation of MgO. The sorbents with 5 wt% and 10 wt% of MgO retained their CO_2 adsorption capacity over multiple cycles. Most importantly, CaO with 10 wt% MgO showed constant CO_2 adsorption capacity over 30 carbonation cycles. The results revealed that CaO with 10 wt% MgO is sufficient to produce sorbents with high surface area, good structural stability and enhanced CO_2 adsorption capacity. (authors)

Enhancement of Two-Dimensional Electron-Gas Properties by Zn Polar ZnMgO/MgO/ZnO Structure Grown by Radical-Source Laser Molecular Beam Epitaxy

Directory of Open Access Journals (Sweden)

Li Meng

2015-01-01

Full Text Available A Zn polar ZnMgO/MgO/ZnO structure with low Mg composition Zn1-xMgxO layer (x = 0.05 grown on a-plane (11–20 sapphire by radical-source laser molecular beam epitaxy was reported. The insertion of a thin (1 nm MgO layer between ZnMgO and ZnO layers in the ZnMgO/ZnO 2DEG structures results in an increase of 2DEG sheet density and affects electron mobility slightly. The carrier concentration reached a value as high as 1.1 × 1013 cm−2, which was confirmed by C-V measurements. A high Hall mobility of 3090 cm2/Vs at 10 K and 332 cm2/Vs at RT was observed from Zn0.95Mg0.05O/MgO/ZnO heterostructure. The choice of the thickness of MgO was discussed. The dependence of carrier sheet density of 2DEG on ZnMgO layer thickness was calculated in theory and the theoretical prediction and experimental results agreed well.

Reducing Mg acceptor activation-energy in Al(0.83)Ga(0.17)N disorder alloy substituted by nanoscale (AlN)₅/(GaN)₁ superlattice using Mg(Ga) δ-doping: Mg local-structure effect.

Science.gov (United States)

Zhong, Hong-xia; Shi, Jun-jie; Zhang, Min; Jiang, Xin-he; Huang, Pu; Ding, Yi-min

2014-10-23

Improving p-type doping efficiency in Al-rich AlGaN alloys is a worldwide problem for the realization of AlGaN-based deep ultraviolet optoelectronic devices. In order to solve this problem, we calculate Mg acceptor activation energy and investigate its relationship with Mg local structure in nanoscale (AlN)5/(GaN)1 superlattice (SL), a substitution for Al(0.83)Ga(0.17)N disorder alloy, using first-principles calculations. A universal picture to reduce acceptor activation energy in wide-gap semiconductors is given for the first time. By reducing the volume of the acceptor local structure slightly, its activation energy can be decreased remarkably. Our results show that Mg acceptor activation energy can be reduced significantly from 0.44 eV in Al(0.83)Ga(0.17)N disorder alloy to 0.26 eV, very close to the Mg acceptor activation energy in GaN, and a high hole concentration in the order of 10(19) cm(-3) can be obtained in (AlN)5/(GaN)1 SL by Mg(Ga) δ-doping owing to GaN-monolayer modulation. We thus open up a new way to reduce Mg acceptor activation energy and increase hole concentration in Al-rich AlGaN.

Intra-individual comparison of different contrast media concentrations (300 mg, 370 mg and 400 mg iodine) in MDCT

Energy Technology Data Exchange (ETDEWEB)

Behrendt, Florian F.; Keil, Sebastian; Plumhans, Cedric; Guenther, Rolf W. [RWTH Aachen University, Department of Diagnostic Radiology, University Hospital, Aachen (Germany); Pietsch, Hubertus; Jost, Gregor; Sieber, Martin A.; Seidensticker, Peter [Bayer Schering Pharma AG, Berlin (Germany); Mahnken, Andreas H. [RWTH Aachen University, Department of Diagnostic Radiology, University Hospital, Aachen (Germany); RWTH Aachen University, Applied Medical Engineering, Helmholtz-Institute for Biomedical Engineering, Aachen (Germany)

2010-07-15

To compare intra-individual contrast enhancement in multi-detector-row computed tomography (MDCT) using contrast media (CM) containing 300, 370 and 400 mg iodine per ml (mgI/ml). Six pigs underwent repeated chest MDCT using three different CM (iopromide 300, iopromide 370, iomeprol 400). An identical iodine delivery (IDR) rate of 1.5 gI/s and a constant total iodine dose of 300 mg/kg body weight were used. Dynamic CT were acquired at the level of the pulmonary artery, and the ascending and descending aorta. After the time enhancement curves were computed, the pulmonary and aortic peak enhancement, time to peak and plateau time above 300 HU were calculated. Intra-individual peak contrast enhancement was significantly higher for the 300 mgI/ml contrast medium compared with the 370 and 400 mgI/ml media: pulmonary trunk 595 HU vs 516 HU (p = 0.0093) vs 472HU (p = 0.0005), and aorta 505 HU vs 454 HU (p = 0.0008) vs 439 HU (p = 0.0001), respectively. Comparison of time to peaks showed no significant difference. Plateau times were significantly longer for the 300 mgI/ml than for the 370 and 400 mgI/ml CM at all anatomical sites. Given normalised IDR and total iodine burden, the use of CM with a standard concentration with 300 mg iodine/ml provides improved contrast enhancement compared with highly concentrated CM in the chest. (orig.)

Preparation of Zn(BH4)2 and diborane and hydrogen release properties of Zn(BH4)2+xMgH2 (x=1, 5, 10, and 15)

Science.gov (United States)

Kwak, Young Jun; Kwon, Sung Nam; Song, Myoung Youp

2015-09-01

Zn(BH4)2 was prepared by milling ZnCl2 and NaBH4 in a planetary ball mill under Ar atmosphere, and Zn(BH4)2+xMgH2 (x=1, 5, 10, and 15) samples were prepared. Diborane (B2H6) and hydrogen release characteristics of the Zn(BH4)2 and Zn(BH4)2+xMgH2 samples were studied. The samples synthesized by milling ZnCl2 and NaBH4 contained Zn(BH4)2 and NaCl, together with small amounts of ZnCl2 and NaBH4. We designated these samples as Zn(BH4)2(+NaCl). The weight loss up to 400 °C of the Zn(BH4)2(+NaCl) sample synthesized by milling 4 h was 11.2 wt%. FT-IR analysis showed that Zn(BH4)2 was formed in the Zn(BH4)2(+NaCl) samples. MgH2 was also milled in a planetary ball mill, and mixed with the Zn(BH4)2(+NaCl) synthesized by milling for 4 h in a mortar and pestle. The weight loss up to 400 °C of Zn(BH4)2(+NaCl)+MgH2 was 8.2 wt%, corresponding to the weight % of diborane and hydrogen released from the Zn(BH4)2(+NaCl)+MgH2 sample, with respect to the sample weight. DTA results of Zn(BH4)2(+NaCl)+xMgH2 showed that the decomposition peak of Zn(BH4)2 was at about 61 °C, and that of MgH2 was at about 370-389 °C.

Energetic effects of ether and ketone functional groups in 9,10-dihydroanthracene compound

International Nuclear Information System (INIS)

Freitas, Vera L.S.; Gomes, Jose R.B.; Ribeiro da Silva, Maria D.M.C.

2010-01-01

The energetic effects caused by replacing one of the methylene groups in the 9,10-dihydroanthracene by ether or ketone functional groups yielding xanthene and anthrone species, respectively, were determined from direct comparison of the standard (p o = 0.1 MPa) molar enthalpies of formation in the gaseous phase, at T = 298.15 K, of these compounds. The experimental static-bomb combustion calorimetry and Calvet microcalorimetry and the computational G3(MP2)//B3LYP method were used to get the standard molar gas-phase enthalpies of formation of xanthene, (41.8 ± 3.5) kJ . mol -1 , and anthrone, (31.4 ± 3.2) kJ . mol -1 . The enthalpic increments for the substitution of methylene by ether and ketone in the parent polycyclic compound (9,10-dihydroanthracene) are -(117.9 ± 5.5) kJ . mol -1 and -(128.3 ± 5.4) kJ . mol -1 , respectively.

Raman-spectroscopic (Fe/Fe+Mg, CO2) and Structural studies of Mg-Fe cordierites

International Nuclear Information System (INIS)

Haefeker, U.

2013-01-01

-determination in cordierite do not consider the effects of peak-broadening and peak-overlaps as a consequence of Fe-incorporation so far. The accuracy of the determination method, which is based on the relation between the intensity ratios of two Si-O stretching vibrations and the CO 2 -peak was increased and correction factors for Fe-bearing samples were obtained. This lead to a significant reduction of the overall error. Improved calibration diagrams which are based on the data of 10 natural Mg-Fe-cordierites with XFe = 0.044-0.76 and CO 2 -contents of 0.12-1.97 wt.%. were obtained using the excitation wavelengths of 488, 515 und 633 nm and these correlation diagrams were then successfully applied to natural cordierite grains in thin sections from a granulite from the Sauwald, Upper Austria. Fe-incorporation leads to various changes within the structure of cordierite. The hexagonal and the orthorhombic polymorph of Fe-cordierite were investigated with Raman-spectroscopy and XRD methods and a detailed structural description was provided. X-ray diffraction of both synthetic Fe-cordierite polymorphs yielded a, c (hex) = 9.8801(16) Å, 9.2852(5) Å and a, b, c (ortho) = 17.2306(2) 20 Å, 9.8239(1) Å, 9.2892(1) Å. The crystal structure was then refined using single crystal data and the obtained structural properties have been compared to the Mg-end-member by focussing on the changes on the octahedral positions. Raman data of the hexagonal Fe-cordierite have also been provided and various peaks could be assigned to certain lattice vibrations by comparing them with the results of quantum-mechanical calculations for cordierite. (author) [de

Preparation and characterisation of Os doped MgB{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Grivel, J.-C., E-mail: jean@dtu.dk; Namazkar, S.; Alexiou, A.; Holte, O.J.

2014-12-15

Highlights: • Polycrystalline osmium doped MgB{sub 2} samples were prepared by solid state route. • Up to 1 at.% Mg can be replaced by Os in the MgB{sub 2} lattice. • T{sub c} decreases at a rate of 2.1 K/at.% Os upon doping. - Abstract: Polycrystalline samples with Mg{sub 1−x}Os{sub x}B{sub 2.04} nominal stoichiometry were made by reacting elemental powders at 800 °C under argon atmosphere. Based on XRD diffraction patterns, EDS analysis and magnetisation measurements, it is found that Os can replace up to about 1 at.% Mg in the MgB{sub 2} lattice. Beyond this doping level, unreacted Os and Mg-rich Mg–Os impurity phases are formed. The a-axis parameter contracts upon doping while the superconducting transition temperature decreases at a rate of 2.1 K/at.% Os substitution. At 10 K, Os doping induces an improvement of the normalised critical current density under applied magnetic fields in excess of 0.5 T, indicating a modest enhancement of flux pinning in this range.

Quasicrystal-reinforced Mg alloys.

Science.gov (United States)

Kyun Kim, Young; Tae Kim, Won; Hyang Kim, Do

2014-04-01

The formation of the icosahedral phase (I-phase) as a secondary solidification phase in Mg-Zn-Y and Mg-Zn-Al base systems provides useful advantages in designing high performance wrought magnesium alloys. The strengthening in two-phase composites (I-phase + α -Mg) can be explained by dispersion hardening due to the presence of I-phase particles and by the strong bonding property at the I-phase/matrix interface. The presence of an additional secondary solidification phase can further enhance formability and mechanical properties. In Mg-Zn-Y alloys, the co-presence of I and Ca 2 Mg 6 Zn 3 phases by addition of Ca can significantly enhance formability, while in Mg-Zn-Al alloys, the co-presence of the I-phase and Mg 2 Sn phase leads to the enhancement of mechanical properties. Dynamic and static recrystallization are significantly accelerated by addition of Ca in Mg-Zn-Y alloy, resulting in much smaller grain size and more random texture. The high strength of Mg-Zn-Al-Sn alloys is attributed to the presence of finely distributed Mg 2 Sn and I-phase particles embedded in the α -Mg matrix.

Separation of reaction mechanisms at low energy. Study of the reactions: {sup 27}Al(d,p) {sup 28}Al, {sup 24}Mg(d,p) {sup 25}Mg, and {sup 24}Mg(d, {alpha}) {sup 22}Na; Sur la separation des mecanismes de reaction a basse energie. Etude des reactions: {sup 27}Al(d,p) {sup 28}Al, {sup 24}Mg(d,p) {sup 25}Mg, et {sup 24}Mg(d, {alpha}) {sup 22}Na

Energy Technology Data Exchange (ETDEWEB)

Mermaz, M. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-06-01

The two sets of angular distributions of (d,p) reactions on Al and Mg, measured between 2 and 6 MeV, have given the possibility to test, in analysing the statistical fluctuations of cross-section, the validity of the separation of their mean values in two parts, one 'direct', another given by the statistical mechanism. With the same method of analysis we have studied excitation functions for several alpha groups of the reaction {sup 24}Mg(d, {alpha}) {sup 22}Na and given an evidence for an intermediate structure for the alpha channel leading to the 3. excited state of {sup 22}Na. The angular distribution of the wide resonance at 15.9 MeV in {sup 26}Al has been obtained. (author) [French] Les deux ensembles de distributions angulaires des reactions (d,p) sur Al et Mg, mesures entre 2 et 6 MeV, nous ont permis, en analysant les fluctuations statistiques de sections efficaces, de verifier la possibilite de la separation de leurs valeurs moyennes en deux composantes: l'une 'directe', l'autre due au mecanisme statistique. Avec la meme methode d'analyse nous avons etudie les fonctions d'excitation des premiers groupes alpha de la reaction {sup 24}Mg(d,{alpha}) {sup 22}Na et mis en evidence une structure intermediaire pour la voie de reaction aboutissant au 3eme niveau de {sup 22}Na. Nous avons obtenu la distribution angulaire de la resonance large situee a une energie d'excitation de 15,9 MeV dans {sup 26}Al. (auteur)

Separation of reaction mechanisms at low energy. Study of the reactions: {sup 27}Al(d,p) {sup 28}Al, {sup 24}Mg(d,p) {sup 25}Mg, and {sup 24}Mg(d, {alpha}) {sup 22}Na; Sur la separation des mecanismes de reaction a basse energie. Etude des reactions: {sup 27}Al(d,p) {sup 28}Al, {sup 24}Mg(d,p) {sup 25}Mg, et {sup 24}Mg(d, {alpha}) {sup 22}Na

Energy Technology Data Exchange (ETDEWEB)

Mermaz, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-06-01

The two sets of angular distributions of (d,p) reactions on Al and Mg, measured between 2 and 6 MeV, have given the possibility to test, in analysing the statistical fluctuations of cross-section, the validity of the separation of their mean values in two parts, one 'direct', another given by the statistical mechanism. With the same method of analysis we have studied excitation functions for several alpha groups of the reaction {sup 24}Mg(d, {alpha}) {sup 22}Na and given an evidence for an intermediate structure for the alpha channel leading to the 3. excited state of {sup 22}Na. The angular distribution of the wide resonance at 15.9 MeV in {sup 26}Al has been obtained. (author) [French] Les deux ensembles de distributions angulaires des reactions (d,p) sur Al et Mg, mesures entre 2 et 6 MeV, nous ont permis, en analysant les fluctuations statistiques de sections efficaces, de verifier la possibilite de la separation de leurs valeurs moyennes en deux composantes: l'une 'directe', l'autre due au mecanisme statistique. Avec la meme methode d'analyse nous avons etudie les fonctions d'excitation des premiers groupes alpha de la reaction {sup 24}Mg(d,{alpha}) {sup 22}Na et mis en evidence une structure intermediaire pour la voie de reaction aboutissant au 3eme niveau de {sup 22}Na. Nous avons obtenu la distribution angulaire de la resonance large situee a une energie d'excitation de 15,9 MeV dans {sup 26}Al. (auteur)

Effects of Tadalafil 5 mg Dosed Once Daily in Men with Premature Ejaculation.

Science.gov (United States)

Ozcan, Levent; Polat, Emre Can; Onen, Efe; Kocaaslan, Ramazan; Otunctemur, Alper; Cekmen, Mustafa; Eraldemir, Ceyla; Ozbek, Emin

2017-01-01

In this study, we evaluated the effect of 5 mg tadalafil once daily in men with premature ejaculation (PE). Thirty married men with lifelong PE and 30 healthy men as control group were included in this study. All the patients received 5 mg tadalafil once a day for a month. The international index of erectile function questionnaire and intravaginal ejaculatory latency times (IELTs) and PE profile were recorded before and after treatment. Plasma samples were collected before and after treatment. The mean baseline IELTs was 40.8 ± 8.1 s in the PE group and 196.5 ± 26.2 s in the control group. After treatment in the PE group, the mean IELTs values showed a statistically significant improvement from the baseline values. At the end of 4 weeks, in the PE group, the mean IELT values showed a statistically significant improvement from the baseline values. Baseline serum nitric oxide (NO) levels were 27.3 ± 1.7 in the PE group and in the 31.1 ± 1.4 healthy control groups. After treatment, NO levels were increased from baseline. We consider that 5 mg tadalafil once daily is safety and effective for the treatment of PE. © 2016 S. Karger AG, Basel.

Superconducting properties of MgB2 particle impregnated with Mg-based alloys

International Nuclear Information System (INIS)

Shimizu, Yusuke; Matsuda, Kenji; Mizutani, Manabu; Nishimura, Katsuhiko; Kawabata, Tokimasa; Ikeno, Susumu; Hishinuma, Yoshimitsu; Aoyama, Shigeki

2011-01-01

The three-dimensional penetration method combined with semi-solid casting (SS-3DPC) was utilized to prepare magnesium diboride (MgB 2 ) powder composite materials with various host materials of Mg, Mg-3%Al, Mg-3%Al-1%Zn, Mg-9%Al, and Mg-9%Al-1%Zn. X-ray diffraction measurements indicated predominant peak patterns of MgB 2 and a host alloy, implying that the host material tightly bonded MgB 2 grains without melting the MgB 2 powder. This was confirmed by SEM images. Measured electrical resistivity and magnetization versus temperature showed clear signals of superconducting transition temperature of 27-38 K for all the samples cut out from the billets. Magnetic hysteresis loop observed at 5 K enabled us to estimate a critical current density (J c ) based on the extended Bean model. Additions of aluminum and zinc elements to magnesium host-matrix were found to enhance J c and increase residual resistivity (ρ 0 ) suggesting that aluminum and zinc have an effect on pinning magnetic flux flow for J c enhancement, and scattering conduction electrons for increase of ρ 0 . (author)

Mg-doped nano ferrihydrite - A new adsorbent for fluoride removal from aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Mohapatra, M., E-mail: mamatamohapatra@yahoo.com [Institute of Minerals and Materials Technology, Bhubaneswar 751 013, Orissa (India); Hariprasad, D.; Mohapatra, L.; Anand, S.; Mishra, B.K. [Institute of Minerals and Materials Technology, Bhubaneswar 751 013, Orissa (India)

2012-03-01

The present study evaluates synthesized Mg-doped nano ferrihydrite powder as an adsorbent for F{sup -} removal from aqueous solutions. High surface area Mg-doped ferrihydrite was prepared by co-precipitation method under controlled conditions. Samples were prepared by varying Mg content in the range of 0.39-1.12%. Preliminary test work revealed that under similar conditions, with the increase in Mg content from 0.39 to 0.98% in doped ferrihydrite, % F{sup -} adsorption increased from 66 to 91%. Hence this sample was characterized by XRD, TEM, SAED and TG-DTA. Batch adsorption experiments were carried out by varying contact time (30-480 min), initial pH (1.0-10), initial fluoride concentration (10-150 mg/L), adsorbent dose (0.5-4 g/L), temperature (20-45 Degree-Sign C) and Cl{sup -} or SO{sub 4}{sup 2-} concentrations (nil to 50 mg/L). The results showed 0.98% Mg-doped ferrihydrite to be an excellent fluoride adsorbent giving maximum adsorption capacity of 64 mg/g. The time data fitted well to pseudo second order kinetic model. The isothermal data followed Langmuir model. Thermodynamic parameters confirmed the adsorption process to be spontaneous and endothermic. 89% of fluoride could be desorbed from loaded sample using 1 M NaOH.

Selective antibacterial effects of mixed ZnMgO nanoparticles

International Nuclear Information System (INIS)

Vidic, Jasmina; Stankic, Slavica; Haque, Francia; Ciric, Danica; Le Goffic, Ronan; Vidy, Aurore; Jupille, Jacques; Delmas, Bernard

2013-01-01

Antibiotic resistance has impelled the research for new agents that can inhibit bacterial growth without showing cytotoxic effects on humans and other species. We describe the synthesis and physicochemical characterization of nanostructured ZnMgO whose antibacterial activity was compared to its pure nano-ZnO and nano-MgO counterparts. Among the three oxides, ZnO nanocrystals—with the length of tetrapod legs about 100 nm and the diameter about 10 nm—were found to be the most effective antibacterial agents since both Gram-positive (B. subtilis) and Gram-negative (E. coli) bacteria were completely eradicated at concentration of 1 mg/mL. MgO nanocubes (the mean cube size ∼50 nm) only partially inhibited bacterial growth, whereas ZnMgO nanoparticles (sizes corresponding to pure particles) revealed high specific antibacterial activity to Gram-positive bacteria at this concentration. Transmission electron microscopy analysis showed that B. subtilis cells were damaged after contact with nano-ZnMgO, causing cell contents to leak out. Our preliminary toxicological study pointed out that nano-ZnO is toxic when applied to human HeLa cells, while nano-MgO and the mixed oxide did not induce any cell damage. Overall, our results suggested that nanostructured ZnMgO, may reconcile efficient antibacterial efficiency while being a safe new therapeutic for bacterial infections.

Selective antibacterial effects of mixed ZnMgO nanoparticles

Science.gov (United States)

Vidic, Jasmina; Stankic, Slavica; Haque, Francia; Ciric, Danica; Le Goffic, Ronan; Vidy, Aurore; Jupille, Jacques; Delmas, Bernard

2013-05-01

Antibiotic resistance has impelled the research for new agents that can inhibit bacterial growth without showing cytotoxic effects on humans and other species. We describe the synthesis and physicochemical characterization of nanostructured ZnMgO whose antibacterial activity was compared to its pure nano-ZnO and nano-MgO counterparts. Among the three oxides, ZnO nanocrystals—with the length of tetrapod legs about 100 nm and the diameter about 10 nm—were found to be the most effective antibacterial agents since both Gram-positive ( B. subtilis) and Gram-negative ( E. coli) bacteria were completely eradicated at concentration of 1 mg/mL. MgO nanocubes (the mean cube size 50 nm) only partially inhibited bacterial growth, whereas ZnMgO nanoparticles (sizes corresponding to pure particles) revealed high specific antibacterial activity to Gram-positive bacteria at this concentration. Transmission electron microscopy analysis showed that B. subtilis cells were damaged after contact with nano-ZnMgO, causing cell contents to leak out. Our preliminary toxicological study pointed out that nano-ZnO is toxic when applied to human HeLa cells, while nano-MgO and the mixed oxide did not induce any cell damage. Overall, our results suggested that nanostructured ZnMgO, may reconcile efficient antibacterial efficiency while being a safe new therapeutic for bacterial infections.

Selective antibacterial effects of mixed ZnMgO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Vidic, Jasmina, E-mail: jasmina.vidic@jouy.inra.fr [VIM, Institut de la Recherche Agronomique (France); Stankic, Slavica, E-mail: slavica.stankic@insp.jussieu.fr; Haque, Francia [CNRS, Institut des Nanosciences de Paris, UMR 7588 (France); Ciric, Danica; Le Goffic, Ronan; Vidy, Aurore [VIM, Institut de la Recherche Agronomique (France); Jupille, Jacques [CNRS, Institut des Nanosciences de Paris, UMR 7588 (France); Delmas, Bernard [VIM, Institut de la Recherche Agronomique (France)

2013-05-15

Antibiotic resistance has impelled the research for new agents that can inhibit bacterial growth without showing cytotoxic effects on humans and other species. We describe the synthesis and physicochemical characterization of nanostructured ZnMgO whose antibacterial activity was compared to its pure nano-ZnO and nano-MgO counterparts. Among the three oxides, ZnO nanocrystals-with the length of tetrapod legs about 100 nm and the diameter about 10 nm-were found to be the most effective antibacterial agents since both Gram-positive (B. subtilis) and Gram-negative (E. coli) bacteria were completely eradicated at concentration of 1 mg/mL. MgO nanocubes (the mean cube size {approx}50 nm) only partially inhibited bacterial growth, whereas ZnMgO nanoparticles (sizes corresponding to pure particles) revealed high specific antibacterial activity to Gram-positive bacteria at this concentration. Transmission electron microscopy analysis showed that B. subtilis cells were damaged after contact with nano-ZnMgO, causing cell contents to leak out. Our preliminary toxicological study pointed out that nano-ZnO is toxic when applied to human HeLa cells, while nano-MgO and the mixed oxide did not induce any cell damage. Overall, our results suggested that nanostructured ZnMgO, may reconcile efficient antibacterial efficiency while being a safe new therapeutic for bacterial infections.

Optical absorption and thermoluminescence in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature

International Nuclear Information System (INIS)

Delgado, L.

1984-01-01

Optical absorption and thermoluminescence (TL) studies in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature are presented. In pure Mg O the thermal annihilation of Fe3+ by recombination with thermally released electrons at ∼ 90 and 175 degree centigree and the V center annealing by hole release up to 100 degree centigree cause the observed glow peaks at these temperatures. The TL excitation spectrum shows two maxima at 245 nm (electron center) and 288 nm (Fe3+). In Mg O:Ni X irradiation induces Fe 2 + →- Fe 3 + and Ni 2 + → Ni 3 + oxidations. Two TL emission bands centered at 110 degree centigree (red) and 80 o C (green) are assigned to electron release and their recombination at Fe 3 + and Ni 3 + respectively. In Mg O:Li two TL emission bands, one blue (430 nm) and the other red (730 nm) with excitation maxima at 245 nm (electron center) and 200 nm (hole center) respectively are observed. No V-center formation was detected in both Ni and Li doped samples. (Author) 42 refs

Beryllium fluoride exchange rate accelerated by Mg²⁺ as discovered by ¹⁹F NMR.

Science.gov (United States)

Liu, Yixiang; Mao, Xi-an; Liu, Maili; Jiang, Ling

2015-01-08

Beryllium fluoride is widely used as a phosphoryl analogue in macromolecular studies, which are not only fluoride-sensitive but also magnesium-dependent. The beryllium fluorides are a mixture of different species including BeF3(-) and BeF4(2-) exchanging under thermodynamic equilibrium in neutral aqueous solutions. In the cases of mimicking phosphate group transfer, both beryllium fluoride and the magnesium ion are generally needed. However, the impact of magnesium on the bioactivity of beryllium fluoride is not clear. We have found by (19)F NMR spectroscopy that Mg(2+) can severely affect the chemical exchange kinetics between BeF3(-) and BeF4(2-). When the F(-) concentration is relatively low, the presence of 10.0 mM Mg(2+) can accelerate the exchange rate 3-4 fold. However, when the F(-) concentration is relatively high, the Mg(2+) effect on the chemical exchange vanishes. On the basis of these findings, we proposed a possible mechanism that BeF4(2-) and Mg(2+) form an ion pair that affects the distribution of beryllium fluoride species and thus the activity in the solution.

Electromagnetic densification of MgB2/Cu wires

International Nuclear Information System (INIS)

Woźniak, M; Glowacki, B A

2014-01-01

Electromagnetic compaction of in situ MgB 2 /Cu wire has been achieved using a custom-built 200 J device. The monofilament core packing density was increased by 8% and up to 31% for unreacted and reacted wires respectively. The higher density of the MgB 2 core resulted in a critical current density increase of up to 75% in comparison to that for cold-drawn-only wire. Applying this treatment to a wire with Cu powder additions to the core and with an optimized heat treatment resulted in one of the highest ever reported values of J c for MgB 2 /Cu wires of 6.83 × 10 3  A cm −2 at 4.2 K and 6 T. (paper)

Mg co-ordination with potential carcinogenic molecule acrylamide: Spectroscopic, computational and cytotoxicity studies

Science.gov (United States)

Singh, Ranjana; Mishra, Vijay K.; Singh, Hemant K.; Sharma, Gunjan; Koch, Biplob; Singh, Bachcha; Singh, Ranjan K.

2018-03-01

Acrylamide (acr) is a potential toxic molecule produced in thermally processed food stuff. Acr-Mg complex has been synthesized chemically and characterized by spectroscopic techniques. The binding sites of acr with Mg were identified by experimental and computational methods. Both experimental and theoretical results suggest that Mg coordinated with the oxygen atom of Cdbnd O group of acr. In-vitro cytotoxicity studies revealed significant decrease in the toxic level of acr-Mg complex as compared to pure acr. The decrease in toxicity on complexation with Mg may be a useful step for future research to reduce the toxicity of acr.

Development of a Hydrogen Uptake-Release Mg-Based Alloy by Adding a Polymer CMC (Carboxymethylcellulose, Sodium Salt) via Reaction-Accompanying Milling

Science.gov (United States)

Kwak, Young Jun; Choi, Eunho; Song, Myoung Youp

2018-03-01

The addition of carboxymethylcellulose, sodium salt (CMC) might improve the hydrogen uptake and release properties of Mg since it has a relatively low melting point and the melting of CMC during milling in hydrogen (reaction-accompanying milling) may make the milled samples be in good states to absorb and release hydrogen rapidly and to have a large hydrogen-storage capacity. Samples with compositions of 95 w/o Mg + 5 w/o CMC (named Mg-5CMC) and 90 w/o Mg + 10 w/o CMC (named Mg-10CMC) were prepared by adding CMC via reaction-accompanying milling. Activation of Mg-10CMC was completed after about 3 hydrogen uptake-release cycles. Mg-10CMC had a higher initial hydrogen uptake rate and a larger amount of hydrogen absorbed in 60 min, U (60 min), than Mg-5CMC before and after activation. At the cycle number of three (CN = 3), Mg-10CMC had a very high initial hydrogen uptake rate (1.56 w/o H/min) and a large U (60 min) (5.57 w/o H) at 593 K in hydrogen of 12 bar, showing that the activated Mg-10CMC has an effective hydrogen-storage capacity of about 5.6 w/o at 593 K in hydrogen of 12 bar at CN = 3. At CN = 2, Mg-10CMC released 1.00 w/o H in 2.5 min, 4.67 w/o H in 10 min, and 4.76 w/o H in 60 min at 648 K in hydrogen of 1.0 bar. The milling in hydrogen of Mg with CMC is believed to generate imperfections and cracks and reduce the particle size. The addition of 10 w/o CMC was more effective on the initial hydrogen uptake rate and U (60 min) compared with the 10 w/o additions of NbF5, TaF5, Fe2O3, and MnO, and the 10 w/o simultaneous addition of Ni, Fe, and Ti. To the best of our knowledge, this study is the first in which a polymer CMC is added to Mg by reaction-accompanying milling to improve the hydrogen storage properties of Mg.

Dose finding study of granisetron in patients receiving high-dose cisplatin chemotherapy. The Granisetron Study Group.

Science.gov (United States)

Riviere, A.

1994-01-01

The efficacy and safety of three different doses of granisetron (2 micrograms kg-1, group A; 10 micrograms kg-1, group B; 40 micrograms kg-1, group C) were compared in a randomised, double-blind study of 157 patients due to receive high-dose cisplatin therapy (mean dose > 97 mg m-2). In each group, up to two 3 mg rescue doses of granisetron were allowed if more than mild nausea or vomiting occurred. In group A 30.8%, in group B 61.5% and in group C 67.9% of patients were complete responders (i.e. no vomiting or nothing worse than mild nausea) during the first 24 h. These differences are significant between groups A and B, and A and C. There were no statistically significant differences in any efficacy variable between the 10 micrograms kg-1 and 40 micrograms kg-1 groups, although in each case the trend favoured the higher dose. Additional rescue doses resulted in resolved or improved symptoms in 95.3% for the first rescue dose and 93.3% for the second. Over the 7 days of the study, 82.7%, 82.7% and 86.8% of patients in groups A, B and C respectively were treated with granisetron alone. Headache was the most common side-effect, reported by 9.6% of patients; the majority of headaches were mild. There was no difference between the treatment groups regarding the adverse event rate. We concluded that prophylactic doses of 10 or 40 micrograms kg-1 lead to a safe and satisfactory degree of control of nausea and vomiting induced by high-dose cisplatin. PMID:8180032

The impact of a 600-mg loading dose of clopidogrel in diabetic and non-diabetic patients undergoing elective PCI.

Science.gov (United States)

Mohareb, Mina W; Abd Elghany, Mohamed; Sabry, Nirmeen A; Farid, Samar F

2016-08-01

High platelet reactivity (HPR) and suboptimal response to dual antiplatelet therapy (DAPT) may explain high recurrent rates of ischemic events in type 1 and 2 diabetes mellitus (DM) patients undergoing percutaneous coronary intervention (PCI). The aim of this study was to determine the effect of diabetes mellitus on clopidogrel activity in cardiac patients undergoing PCI. This is an observational study. Patients were categorized according to DM status into diabetic group (N.=30) and non-diabetic group (N.=33). All patients received clopidogrel in a loading dose of 600 mg before PCI. Platelet function was assessed using light transmittance aggregometry (LTA) technique at baseline (before clopidogrel administration), 24 hour after clopidogrel loading dose administration and 7-10 days after PCI. All patients were followed up for at least one year after PCI for recurrence of acute cardiac events. There was no statistically significant difference between the two groups with respect to 10 µm adenosine diphosphate (ADP)-induced platelet aggregation measured at baseline (P=0.64), 24 hours after PCI (P=0.874), and 7-10 days after PCI (0.643). Diabetics were not significantly different from non-diabetics in terms of post-PCI acute stent thrombosis (P=0.945), sub-acute stent thrombosis (P=0.945), unstable angina (P=0.29) and cardiac death (P=0.64). There was a statistically significant difference between patients with and without post-PCI acute events regarding ADP aggregation measured 24 hours and 7-10 days after PCI. The use of a high loading dose of clopidogrel (600 mg) in patients undergoing elective PCI can overcome the significant increase in post-PCI platelet aggregation and rate of acute cardiac events induced by diabetes mellitus as co-morbidity in those patients.

Enhanced Optical Performance of BaMgAl

NARCIS (Netherlands)

Yin, L.J.; Dong, Juntao; Wang, Yinping; Zhang, Bi; Zhou, Zheng Yang; Jian, Xian; Wu, Mengqiang; Xu, Xin; van Ommen, J.R.; Hintzen, H.T.J.M.

2016-01-01

Many strategies have been adopted to improve thermal degradation of phosphors. Because of the stability and high transmittance of graphene, here we report a novel method of carbon coating on BaMgAl₁₀O₁₇:Eu²⁺ (BAM) phosphor particles through chemical vapor

The Influence of MgH2 on the Assessment of Electrochemical Data to Predict the Degradation Rate of Mg and Mg Alloys

Directory of Open Access Journals (Sweden)

Wolf-Dieter Mueller

2014-06-01

Full Text Available Mg and Mg alloys are becoming more and more of interest for several applications. In the case of biomaterial applications, a special interest exists due to the fact that a predictable degradation should be given. Various investigations were made to characterize and predict the corrosion behavior in vitro and in vivo. Mostly, the simple oxidation of Mg to Mg2+ ions connected with adequate hydrogen development is assumed, and the negative difference effect (NDE is attributed to various mechanisms and electrochemical results. The aim of this paper is to compare the different views on the corrosion pathway of Mg or Mg alloys and to present a neglected pathway based on thermodynamic data as a guideline for possible reactions combined with experimental observations of a delay of visible hydrogen evolution during cyclic voltammetry. Various reaction pathways are considered and discussed to explain these results, like the stability of the Mg+ intermediate state, the stability of MgH2 and the role of hydrogen overpotential. Finally, the impact of MgH2 formation is shown as an appropriate base for the prediction of the degradation behavior and calculation of the corrosion rate of Mg and Mg alloys.

Structural characteristics and corrosion behavior of biodegradable Mg-Zn, Mg-Zn-Gd alloys.

Science.gov (United States)

Kubásek, J; Vojtěch, D

2013-07-01

In this research, binary Mg-Zn (up to 3 wt% Zn) and ternary Mg-Zn-Gd (up to 3 wt% Gd, 3 wt% Zn) alloys were prepared by induction melting in an argon atmosphere. The structures of these alloys were characterized using light and scanning electron microscopy, energy dispersive spectrometry, X-ray diffraction and X-ray fluorescence. In addition, Brinell hardness measurements were taken to supplement these studies. Corrosion behavior was evaluated by immersion tests and potentiodynamic measurements in a physiological solution (9 g/l NaCl). Depending on the composition, structures of the as-cast alloys contained α-Mg dendrites, MgZn, Mg5Gd and Mg3Gd2Zn3 phases. Compared to pure Mg, zinc improved the corrosion resistance of binary Mg-Zn. Gadolinium also improved the corrosion resistance in the case of Mg-1Zn-3Gd alloy. The highest corrosion rate was observed for Mg-3Zn-3Gd alloy. Our results improve the understanding of the relationships between the structure and corrosion behavior of our studied alloy systems.

Coherent interface structures and intergrain Josephson coupling in dense MgO/Mg{sub 2}Si/MgB{sub 2} nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Ueno, Katsuya; Takahashi, Kazuyuki; Uchino, Takashi, E-mail: uchino@kobe-u.ac.jp [Department of Chemistry, Graduate School of Science, Kobe University, Nada, Kobe 657-8501 (Japan); Nagashima, Yukihito [Nippon Sheet Glass Co., Ltd., Konoike, Itami 664-8520 (Japan); Seto, Yusuke [Department of Planetology, Graduate School of Science, Kobe University, Nada, Kobe 657-8501 (Japan); Matsumoto, Megumi; Sakurai, Takahiro [Center for Support to Research and Education Activities, Kobe University, Nada, Kobe 657-8501 (Japan); Ohta, Hitoshi [Molecular Photoscience Research Center, Kobe University, Nada, Kobe 657-8501 (Japan)

2016-07-07

Many efforts are under way to control the structure of heterointerfaces in nanostructured composite materials for designing functionality and engineering application. However, the fabrication of high-quality heterointerfaces is challenging because the crystal/crystal interface is usually the most defective part of the nanocomposite materials. In this work, we show that fully dense insulator (MgO)/semiconductor(Mg{sub 2}Si)/superconductor(MgB{sub 2}) nanocomposites with atomically smooth and continuous interfaces, including epitaxial-like MgO/Mg{sub 2}Si interfaces, are obtained by solid phase reaction between metallic magnesium and a borosilicate glass. The resulting nanocomposites exhibit a semiconductor-superconducting transition at 36 K owing to the MgB{sub 2} nanograins surrounded by the MgO/Mg{sub 2}Si matrix. This transition is followed by the intergrain phase-lock transition at ∼24 K due to the construction of Josephson-coupled network, eventually leading to a near-zero resistance state at 17 K. The method not only provides a simple process to fabricate dense nanocomposites with high-quality interfaces, but also enables to investigate the electric and magnetic properties of embedded superconducting nanograins with good intergrain coupling.

Growth and scintillation properties of BaMgF4

International Nuclear Information System (INIS)

Yanagida, Takayuki; Kawaguchi, Noriaki; Fujimoto, Yutaka; Sugiyama, Makoto; Furuya, Yuki; Kamada, Kei; Yokota, Yuui; Yoshikawa, Akira; Chani, Valery

2010-01-01

By using the micro-pulling down (μ-PD) method, the barium magnesium fluoride (BaMgF 4 ) single crystalline scintillator was produced. The crystal was cut and mirror polished to the physical dimensions of 1x2x10 mm 3 for examination of scintillation properties. BaMgF 4 demonstrated ∼70% transmittance in wavelength range above 170 nm, and strong emission peaking around 205 nm was observed under X-ray excitation. The absolute light yield of BaMgF 4 was 1300±100 ph/MeV, and the decay time profile showed two components as 0.57±0.01 (70%) and 2.2±0.31 (30%) ns at room temperature.

The Effects of Temperature and Salinity on Mg Incorporation in Planktonic Foraminifera Globigerinoides ruber (white): Results from a Global Sediment Trap Mg/Ca Database

Science.gov (United States)

Gray, W. R.; Weldeab, S.; Lea, D. W.

2015-12-01

Mg/Ca in Globigerinoides ruber is arguably the most important proxy for sea surface temperature (SST) in tropical and sub tropical regions, and as such guides our understanding of past climatic change in these regions. However, the sensitivity of Mg/Ca to salinity is debated; while analysis of foraminifera grown in cultures generally indicates a sensitivity of 3 - 6% per salinity unit, core-top studies have suggested a much higher sensitivity of between 15 - 27% per salinity unit, bringing the utility of Mg/Ca as a SST proxy into dispute. Sediment traps circumvent the issues of dissolution and post-depositional calcite precipitation that hamper core-top calibration studies, whilst allowing the analysis of foraminifera that have calcified under natural conditions within a well constrained period of time. We collated previously published sediment trap/plankton tow G. ruber (white) Mg/Ca data, and generated new Mg/Ca data from a sediment trap located in the highly-saline tropical North Atlantic, close to West Africa. Calcification temperature and salinity were calculated for the time interval represented by each trap/tow sample using World Ocean Atlas 2013 data. The resulting dataset comprises >240 Mg/Ca measurements (in the size fraction 150 - 350 µm), that span a temperature range of 18 - 28 °C and 33.6 - 36.7 PSU. Multiple regression of the dataset reveals a temperature sensitivity of 7 ± 0.4% per °C (p < 2.2*10-16) and a salinity sensitivity of 4 ± 1% per salinity unit (p = 2*10-5). Application of this calibration has significant implications for both the magnitude and timing of glacial-interglacial temperature changes when variations in salinity are accounted for.

[Pharmacokinetics and clinical studies on flomoxef in neonates and premature infants. A study of flomoxef in the perinatal collaboration research group].

Science.gov (United States)

Fujii, R; Fujita, K; Murono, K; Saijo, M; Kakuya, F; Yoshioka, H; Maruyama, S; Sakata, H; Hiramoto, A; Inyaku, F

1993-07-01

We investigated pharmacokinetics and clinical effects of flomoxef sodium (6315-S, FMOX) in neonates and premature infants. These results are summarized as follows: 1. Pharmacokinetics (1) Plasma concentration (Ct) and half-lives (T1/2) were determined upon after intravenous one-shot injection (i.v.) of FMOX to neonates of different day-age groups (0-3 (n = 25), 4-7 (n = 18), 8-28 (n = 32) days of birth). At a dose of 10 mg/kg. i.v., mean C30 (30 minutes concentration) values were 21.2, 21.8 and 21.3 micrograms/ml, respectively, in the different groups mentioned above, and the mean T1/2 values were 3.37, 1.85 and 1.63 hours. At 20 mg/kg i.v., mean C15 (15 minutes concentration) values were 54.4, 51.4 and 50.7 micrograms/ml, and mean T1/2's were 2.99, 2.32 and 1.79 hours, respectively. At a dose of 40 mg/kg i.v., mean C15 values were 104.0, 95.9 and 99.2 micrograms/ml, and the mean T1/2's were 3.40, 1.20 and 1.80 hours, respectively. (2) Plasma concentrations and T1/2 after intravenous one-shot injection of FMOX in premature infants in group (0-3 (n = 14), 4-7 (n = 10), 8-28 (n = 13) days of birth). Mean C15's at doses of 10, 20 and 40 mg/kg in the different groups of infants were 24.0, 28.6, 21.7 and 54.0, 54.6, 55.5 and 98.2, 93.0, 106.0 micrograms/ml, and T1/2's were 4.10, 2.53, 2.57 and 4.28, 2.27, 3.02 and 4.66, 2.86, 2.09 hours, respectively. Mean Cmax values were clearly dose dependent, and mean T1/2 values tended to be longer in premature infants compared to neonates. (3) Urinary recovery rate of FMOX after intravenous injection in neonates and premature infants. Mean urinary recovery rates of FMOX in the first 6 hours after i.v. (one-shot) at doses of 10, 20 and 40 mg/kg to neonates and premature infants were 38.9-62.8% in the neonates and 30.7-61.5% in the premature infants. (4) Plasma concentrations and urinary recovery rates upon 1 hour drip infusion of 20 mg/kg in the neonate groups (or the premature infant groups) as follows: Mean C50 values were 31

Separation of reaction mechanisms at low energy. Study of the reactions: 27Al(d,p) 28Al, 24Mg(d,p) 25Mg, and 24Mg(d, α) 22Na

International Nuclear Information System (INIS)

Mermaz, M.

1966-06-01

The two sets of angular distributions of (d,p) reactions on Al and Mg, measured between 2 and 6 MeV, have given the possibility to test, in analysing the statistical fluctuations of cross-section, the validity of the separation of their mean values in two parts, one 'direct', another given by the statistical mechanism. With the same method of analysis we have studied excitation functions for several alpha groups of the reaction 24 Mg(d, α) 22 Na and given an evidence for an intermediate structure for the alpha channel leading to the 3. excited state of 22 Na. The angular distribution of the wide resonance at 15.9 MeV in 26 Al has been obtained. (author) [fr

A randomized, controlled trial of 3.0 mg of Liraglutide in weight management

DEFF Research Database (Denmark)

Pi-Sunyer, Xavier; Astrup, Arne; Fujioka, Ken

2015-01-01

Background Obesity is a chronic disease with serious health consequences, but weight loss is difficult to maintain through lifestyle intervention alone. Liraglutide, a glucagon-like peptide-1 analogue, has been shown to have potential benefit for weight management at a once-daily dose of 3.0 mg...... or untreated dyslipidemia or hypertension. We randomly assigned patients in a 2:1 ratio to receive once-daily subcutaneous injections of liraglutide at a dose of 3.0 mg (2487 patients) or placebo (1244 patients); both groups received counseling on lifestyle modification. The coprimary end points were...... with liraglutide were mild or moderate nausea and diarrhea. Serious events occurred in 6.2% of the patients in the liraglutide group and in 5.0% of the patients in the placebo group. Conclusions In this study, 3.0 mg of liraglutide, as an adjunct to diet and exercise, was associated with reduced body weight...

Mg-doping experiment and electrical transport measurement of boron nanobelts

International Nuclear Information System (INIS)

Kirihara, K.; Hyodo, H.; Fujihisa, H.; Wang, Z.; Kawaguchi, K.; Shimizu, Y.; Sasaki, T.; Koshizaki, N.; Soga, K.; Kimura, K.

2006-01-01

We measured electrical conductance of single crystalline boron nanobelts having α-tetragonal crystalline structure. The doping experiment of Mg was carried out by vapor diffusion method. The pure boron nanobelt is a p-type semiconductor and its electrical conductivity was estimated to be on the order of 10 -3 (Ω cm) -1 at room temperature. The carrier mobility of pure boron nanobelt was measured to be on the order of 10 -3 (cm 2 Vs -1 ) at room temperature and has an activation energy of ∼0.19 eV. The Mg-doped boron nanobelts have the same α-tetragonal crystalline structure as the pristine nanobelts. After Mg vapor diffusion, the nanobelts were still semiconductor, while the electrical conductance increased by a factor of 100-500. Transition to metal or superconductor by doping was not observed. - Graphical abstract: SEM micrographs of boron nanobelt after Ni/Au electrode fabrication by electron beam lithography. Display Omitted

A method for combined Sr-Nd-Hf isotopic analysis of <10 mg dust samples: implication for ice core science

Science.gov (United States)

Ujvari, Gabor; Wegner, Wencke; Klötzli, Urs

2017-04-01

Aeolian mineral dust particles below the size of 10-20 μm often experience longer distance transport in the atmosphere, and thus Aeolian dust is considered an important tracer of large-scale atmospheric circulation. Since ice core dust is purely Aeolian in origin, discrimination of its potential source region(s) can contribute to a better understanding of past dust activity and climatic/environmental causes. Furthermore, ice core dust source information provides critical experimental constraints for model simulations of past atmospheric circulation patterns [1,2]. However, to identify dust sources in past dust archives such as ice cores, the mineralogy and geochemistry of the wind-blown dust material must be characterized. While the amount of dust in marine cores or common terrestrial archives is sufficient for different types of analyses and even for multiple repeat measurements, dust content in ice cores is usually extremely low even for the peak dusty periods such as the Last Glacial Maximum (LGM) (5-8 mg dust/kg ice; [3]). Since the most powerful dust fingerprinting methods, such as REE composition and Sr-Nd-Pb isotopic analyses are destructive there is a clear need to establish sequential separation techniques of Sr, Nd, Pb and other REEs to get the most information out of small (5-10 mg) dust samples recovered from ice cores. Although Hf isotopes have recently been added as a robust tool of aerosol/dust source discrimination (e.g. [4,5,6,7]), precise Hf isotopic measurements of small (reliable 176Hf/177Hf (and also 87Sr/86Sr, 143Nd/144Nd) ratios. Along with the standards 50, 10 and 5 mg aliquots of the fine (affected by acid treatment and these signatures are extremely stable both within run (0.000008 variability for the three aliquots, i.e. 0.15 ɛNd unit) and between runs of different laboratories (0.00006, ca 1 ɛNd unit). Hf isotopic compositions varied within 1 (NUS) and 5 ɛHf units (BEI) between the three aliquots, but the BEI sample always gave more

Formation of MgZnO alloy under thermodynamic conditions

Energy Technology Data Exchange (ETDEWEB)

Markevich, I.V.; Stara, T.R., E-mail: stara_t@ukr.net; Kuchuk, A.V.; Polishchuk, Yu.O.; Kladko, V.P.

2014-11-15

Mg{sub x}Zn{sub 1−x}O ceramics with x=0.10, 0.15, 0.20, 0.25 and 0.30 were sintered at T{sub s}=700–1250 °C. Photoluminescence (PL) and PL excitation (PLE) spectra as well as X-ray diffraction patterns were measured at 293 K. Bandgap width was evaluated from the position of PLE peak. Non-monotonous dependence of PLE peak position on T{sub s} was observed for all used x. This effect was concluded to be caused by the formation of cubic phase side by side with hexagonal one and the enhancement of this process with increasing T{sub s}, which resulted in the decrease of Mg content in the hexagonal phase at T{sub s}>1000 °C. Temperature range of 1000–1050 °C was found to be the optimum one for the formation of hexagonal MgZnO alloy at used x. It was shown that x=0.20 was the solubility limit of MgO in hexagonal Mg{sub x}Zn{sub 1−x}O ceramics.