WorldWideScience

Sample records for independent environmental parameters

  1. What is the effect of optimum independent parameters on solar heating systems?

    International Nuclear Information System (INIS)

    Kaçan, Erkan; Ulgen, Koray; Kaçan, Erdal

    2015-01-01

    Highlights: • The efficiency effect of 4 independent parameters over the solar heating system are examined. • 3 of 4 independent parameters are found as decisive parameter for system design. • Maximum exergetic efficiency exceeded 11% at optimized process. • Maximum environmental efficiency reached up to 95% at optimized process. • The optimum outside temperature and solar radiation are found as 22 °C and 773 W/m"2 for all responses. - Abstract: Researchers are rather closely involved in Solar Combisystems recently, but there is lack of study that presents the optimum design parameters. Therefore, in this study the influence of the four major variables, namely; outside, inside temperature, solar radiation on horizontal surface and instantaneous efficiency of solar collector on the energetic, exergetic and environmental efficiencies of Solar Combisystems are investigated and system optimization is done by a combination of response surface methodology. Measured parameters and energetic–exergetic and environmental performance curves are found and statistical model is created parallel with the actual data. It is found that statistical model is significant and all “lack-of-fit” values are non-significant. Thus, it is proved that statistical model strongly represents the design model. Outside temperature, solar radiation on horizontal surface and instantaneous efficiency of solar collector are the decisive parameters for all responses but instantaneous efficiency of solar collector is not for environmental efficiency. Maximum exergetic efficiency exceeded 11%, maximum environmental efficiency reached up to 95% at optimized process. The optimum value of the outside temperature and solar radiation are found as 22 °C and 773 W/m"2 for all responses, on the other hand optimum collector efficiency is found around 60% for energetic and exergetic efficiency values. Inside temperature is not a decisive parameter for all responses.

  2. Environmental liability and the independent contractor

    International Nuclear Information System (INIS)

    Gilmour, B.S.

    1999-01-01

    The provisions of the Environmental Protection and Enhancement Act (EPEA) regarding the relationship between a company and an independent contractor were reviewed. The EPEA was introduced in September 1993 and significantly altered the environmental laws in the province of Alberta. The provisions of the EPEA that apply to the petroleum industry are conservation and reclamation as well as provisions concerning release of substances, contaminated sites and penalties. Companies that pollute may be held liable for reclamation, even if the work was carried out by an independent contractor and despite the fact that the independent contractor is not an employee of the company. Under the current EPEA laws, companies may not be able to effectively shift responsibility for environmental liabilities to independent contractors even where the contractor was negligent. This paper presented suggestions regarding contractor agreements and due diligence to help minimize the risk of liability to companies. The paper also discussed the following two types of liabilities under the EPEA's harmful substances section: (1) the obligation to clean up an affected area, and (2) fines and penalties that may be imposed when an offence is committed

  3. Development of computer program ENMASK for prediction of residual environmental masking-noise spectra, from any three independent environmental parameters

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Y.-S.; Liebich, R. E.; Chun, K. C.

    2000-03-31

    Residual environmental sound can mask intrusive4 (unwanted) sound. It is a factor that can affect noise impacts and must be considered both in noise-impact studies and in noise-mitigation designs. Models for quantitative prediction of sensation level (audibility) and psychological effects of intrusive noise require an input with 1/3 octave-band spectral resolution of environmental masking noise. However, the majority of published residual environmental masking-noise data are given with either octave-band frequency resolution or only single A-weighted decibel values. A model has been developed that enables estimation of 1/3 octave-band residual environmental masking-noise spectra and relates certain environmental parameters to A-weighted sound level. This model provides a correlation among three environmental conditions: measured residual A-weighted sound-pressure level, proximity to a major roadway, and population density. Cited field-study data were used to compute the most probable 1/3 octave-band sound-pressure spectrum corresponding to any selected one of these three inputs. In turn, such spectra can be used as an input to models for prediction of noise impacts. This paper discusses specific algorithms included in the newly developed computer program ENMASK. In addition, the relative audibility of the environmental masking-noise spectra at different A-weighted sound levels is discussed, which is determined by using the methodology of program ENAUDIBL.

  4. An impossibility theorem for parameter independent hidden variable theories

    Science.gov (United States)

    Leegwater, Gijs

    2016-05-01

    Recently, Roger Colbeck and Renato Renner (C&R) have claimed that '[n]o extension of quantum theory can have improved predictive power' (Colbeck & Renner, 2011, 2012b). If correct, this is a spectacular impossibility theorem for hidden variable theories, which is more general than the theorems of Bell (1964) and Leggett (2003). Also, C&R have used their claim in attempt to prove that a system's quantum-mechanical wave function is in a one-to-one correspondence with its 'ontic' state (Colbeck & Renner, 2012a). C&R's claim essentially means that in any hidden variable theory that is compatible with quantum-mechanical predictions, probabilities of measurement outcomes are independent of these hidden variables. This makes such variables otiose. On closer inspection, however, the generality and validity of the claim can be contested. First, it is based on an assumption called 'Freedom of Choice'. As the name suggests, this assumption involves the independence of an experimenter's choice of measurement settings. But in the way C&R define this assumption, a no-signalling condition is surreptitiously presupposed, making the assumption less innocent than it sounds. When using this definition, any hidden variable theory violating parameter independence, such as Bohmian Mechanics, is immediately shown to be incompatible with quantum-mechanical predictions. Also, the argument of C&R is hard to follow and their mathematical derivation contains several gaps, some of which cannot be closed in the way they suggest. We shall show that these gaps can be filled. The issue with the 'Freedom of Choice' assumption can be circumvented by explicitly assuming parameter independence. This makes the result less general, but better founded. We then obtain an impossibility theorem for hidden variable theories satisfying parameter independence only. As stated above, such hidden variable theories are impossible in the sense that any supplemental variables have no bearing on outcome probabilities

  5. Independence and the Irish Environmental Protection Agency: A Comparative Assessment

    OpenAIRE

    Shipan, Charles

    2006-01-01

    The Environmental Protection Agency is one of the most prominent regulatory agencies in Ireland. Created in 1992, one of the hallmarks of this agency is its independence from other parts of government. Yet little is known about the actual extent of its independence. Independence and the Irish Environmental Protection Agency: A Comparative Assessment addresses several key questions about the agency's independence. Why was independence such a primary justification for the creation of this a...

  6. Genetic algorithm–based varying parameter linear quadratic regulator control for four-wheel independent steering vehicle

    Directory of Open Access Journals (Sweden)

    Linlin Gao

    2015-11-01

    Full Text Available From the perspective of vehicle dynamics, the four-wheel independent steering vehicle dynamics stability control method is studied, and a four-wheel independent steering varying parameter linear quadratic regulator control system is proposed with the help of expert control method. In the article, a four-wheel independent steering linear quadratic regulator controller for model following purpose is designed first. Then, by analyzing the four-wheel independent steering vehicle dynamic characteristics and the influence of linear quadratic regulator control parameters on control performance, a linear quadratic regulator control parameter adjustment strategy based on vehicle steering state is proposed to achieve the adaptive adjustment of linear quadratic regulator control parameters. In addition, to further improve the control performance, the proposed varying parameter linear quadratic regulator control system is optimized by genetic algorithm. Finally, simulation studies have been conducted by applying the proposed control system to the 8-degree-of-freedom four-wheel independent steering vehicle dynamics model. The simulation results indicate that the proposed control system has better performance and robustness and can effectively improve the stability and steering safety of the four-wheel independent steering vehicle.

  7. Parameters used in the environmental pathways (DESCARTES) and radiological dose (CIDER) modules of the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC) for the air pathway. Hanford Environmental Dose Reconstruction Project

    Energy Technology Data Exchange (ETDEWEB)

    Snyder, S.F.; Farris, W.T.; Napier, B.A.; Ikenberry, T.A.; Gilbert, R.O.

    1992-09-01

    This letter report is a description of work performed for the Hanford Environmental Dose Reconstruction (HEDR) Project. The HEDR Project was established to estimate the radiation doses to individuals resulting from releases of radionuclides from the Hanford Site since 1944. This work is being done by staff at Battelle, Pacific Northwest Laboratories (Battelle) under a contract with the Centers for Disease Control (CDC) with technical direction provided by an independent Technical Steering Panel (TSP). The objective of this report is to-document the environmental accumulation and dose-assessment parameters that will be used to estimate the impacts of past Hanford Site airborne releases. During 1993, dose estimates made by staff at Battelle will be used by the Fred Hutchinson Cancer Research Center as part of the Hanford Thyroid Disease Study (HTDS). This document contains information on parameters that are specific to the airborne release of the radionuclide iodine-131. Future versions of this document will include parameter information pertinent to other pathways and radionuclides.

  8. Parameters used in the environmental pathways (DESCARTES) and radiological dose (CIDER) modules of the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC) for the air pathway

    Energy Technology Data Exchange (ETDEWEB)

    Snyder, S.F.; Farris, W.T.; Napier, B.A.; Ikenberry, T.A.; Gilbert, R.O.

    1992-09-01

    This letter report is a description of work performed for the Hanford Environmental Dose Reconstruction (HEDR) Project. The HEDR Project was established to estimate the radiation doses to individuals resulting from releases of radionuclides from the Hanford Site since 1944. This work is being done by staff at Battelle, Pacific Northwest Laboratories (Battelle) under a contract with the Centers for Disease Control (CDC) with technical direction provided by an independent Technical Steering Panel (TSP). The objective of this report is to-document the environmental accumulation and dose-assessment parameters that will be used to estimate the impacts of past Hanford Site airborne releases. During 1993, dose estimates made by staff at Battelle will be used by the Fred Hutchinson Cancer Research Center as part of the Hanford Thyroid Disease Study (HTDS). This document contains information on parameters that are specific to the airborne release of the radionuclide iodine-131. Future versions of this document will include parameter information pertinent to other pathways and radionuclides.

  9. Parameters used in the environmental pathways (DESCARTES) and radiological dose (CIDER) modules of the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC) for the air pathway

    International Nuclear Information System (INIS)

    Snyder, S.F.; Farris, W.T.; Napier, B.A.; Ikenberry, T.A.; Gilbert, R.O.

    1992-09-01

    This letter report is a description of work performed for the Hanford Environmental Dose Reconstruction (HEDR) Project. The HEDR Project was established to estimate the radiation doses to individuals resulting from releases of radionuclides from the Hanford Site since 1944. This work is being done by staff at Battelle, Pacific Northwest Laboratories (Battelle) under a contract with the Centers for Disease Control (CDC) with technical direction provided by an independent Technical Steering Panel (TSP). The objective of this report is to-document the environmental accumulation and dose-assessment parameters that will be used to estimate the impacts of past Hanford Site airborne releases. During 1993, dose estimates made by staff at Battelle will be used by the Fred Hutchinson Cancer Research Center as part of the Hanford Thyroid Disease Study (HTDS). This document contains information on parameters that are specific to the airborne release of the radionuclide iodine-131. Future versions of this document will include parameter information pertinent to other pathways and radionuclides

  10. Parameter-Independent Dynamical Behaviors in Memristor-Based Wien-Bridge Oscillator

    Directory of Open Access Journals (Sweden)

    Ning Wang

    2017-01-01

    Full Text Available This paper presents a novel memristor-based Wien-bridge oscillator and investigates its parameter-independent dynamical behaviors. The newly proposed memristive chaotic oscillator is constructed by linearly coupling a nonlinear active filter composed of memristor and capacitor to a Wien-bridge oscillator. For a set of circuit parameters, phase portraits of a double-scroll chaotic attractor are obtained by numerical simulations and then validated by hardware experiments. With a dimensionless system model and the determined system parameters, the initial condition-dependent dynamical behaviors are explored through bifurcation diagrams, Lyapunov exponents, and phase portraits, upon which the coexisting infinitely many attractors and transient chaos related to initial conditions are perfectly offered. These results are well verified by PSIM circuit simulations.

  11. An Improved Interferometric Calibration Method Based on Independent Parameter Decomposition

    Science.gov (United States)

    Fan, J.; Zuo, X.; Li, T.; Chen, Q.; Geng, X.

    2018-04-01

    Interferometric SAR is sensitive to earth surface undulation. The accuracy of interferometric parameters plays a significant role in precise digital elevation model (DEM). The interferometric calibration is to obtain high-precision global DEM by calculating the interferometric parameters using ground control points (GCPs). However, interferometric parameters are always calculated jointly, making them difficult to decompose precisely. In this paper, we propose an interferometric calibration method based on independent parameter decomposition (IPD). Firstly, the parameters related to the interferometric SAR measurement are determined based on the three-dimensional reconstruction model. Secondly, the sensitivity of interferometric parameters is quantitatively analyzed after the geometric parameters are completely decomposed. Finally, each interferometric parameter is calculated based on IPD and interferometric calibration model is established. We take Weinan of Shanxi province as an example and choose 4 TerraDEM-X image pairs to carry out interferometric calibration experiment. The results show that the elevation accuracy of all SAR images is better than 2.54 m after interferometric calibration. Furthermore, the proposed method can obtain the accuracy of DEM products better than 2.43 m in the flat area and 6.97 m in the mountainous area, which can prove the correctness and effectiveness of the proposed IPD based interferometric calibration method. The results provide a technical basis for topographic mapping of 1 : 50000 and even larger scale in the flat area and mountainous area.

  12. Parameters for assessing the aquatic environmental impact of cosmetic products.

    Science.gov (United States)

    Vita, N A; Brohem, C A; Canavez, A D P M; Oliveira, C F S; Kruger, O; Lorencini, M; Carvalho, C M

    2018-05-01

    The cosmetic industry's growing concern about the impact of its supply chain on the environment, sustainability of raw materials, and biodiversity increases the need to ensure that the final product has a lower environmental impact. The objective of this review is to summarize and compare the information available from international organizations and legislation regarding the main criteria used to assess raw materials for aquatic toxicity, as well as the most suitable alternative methods for obtaining assessment parameters. Using the literature available in databases, a review of the scientific literature and international legislation, this work discusses and compares the parameters established by international organizations such as the Environmental Protection Agency (EPA) and Cradle to Cradle (C2C), as well as European legislation, namely, European Regulation 1272/2008, for assessing environmental impact. Defining the ecotoxicity parameters of the main classes of raw materials in rinse-off cosmetic products can enable the development of products that are more environmentally sustainable, prioritizing substances with less environmental impact. Copyright © 2018 Elsevier B.V. All rights reserved.

  13. Model comparisons and genetic and environmental parameter ...

    African Journals Online (AJOL)

    arc

    Model comparisons and genetic and environmental parameter estimates of growth and the ... breeding strategies and for accurate breeding value estimation. The objectives ...... Sci. 23, 72-76. Van Wyk, J.B., Fair, M.D. & Cloete, S.W.P., 2003.

  14. Number of independent parameters in the potentiometric titration of humic substances.

    Science.gov (United States)

    Lenoir, Thomas; Manceau, Alain

    2010-03-16

    With the advent of high-precision automatic titrators operating in pH stat mode, measuring the mass balance of protons in solid-solution mixtures against the pH of natural and synthetic polyelectrolytes is now routine. However, titration curves of complex molecules typically lack obvious inflection points, which complicates their analysis despite the high-precision measurements. The calculation of site densities and median proton affinity constants (pK) from such data can lead to considerable covariance between fit parameters. Knowing the number of independent parameters that can be freely varied during the least-squares minimization of a model fit to titration data is necessary to improve the model's applicability. This number was calculated for natural organic matter by applying principal component analysis (PCA) to a reference data set of 47 independent titration curves from fulvic and humic acids measured at I = 0.1 M. The complete data set was reconstructed statistically from pH 3.5 to 9.8 with only six parameters, compared to seven or eight generally adjusted with common semi-empirical speciation models for organic matter, and explains correlations that occur with the higher number of parameters. Existing proton-binding models are not necessarily overparametrized, but instead titration data lack the sensitivity needed to quantify the full set of binding properties of humic materials. Model-independent conditional pK values can be obtained directly from the derivative of titration data, and this approach is the most conservative. The apparent proton-binding constants of the 23 fulvic acids (FA) and 24 humic acids (HA) derived from a high-quality polynomial parametrization of the data set are pK(H,COOH)(FA) = 4.18 +/- 0.21, pK(H,Ph-OH)(FA) = 9.29 +/- 0.33, pK(H,COOH)(HA) = 4.49 +/- 0.18, and pK(H,Ph-OH)(HA) = 9.29 +/- 0.38. Their values at other ionic strengths are more reliably calculated with the empirical Davies equation than any existing model fit.

  15. Topological and Graph-Coloring Conditions on the Parameter-Independent Stability of Second-Order Networked Systems

    NARCIS (Netherlands)

    Koerts, Filip; Bürger, Mathias; van der Schaft, Abraham; De Persis, Claudio

    2017-01-01

    In this paper, we study parameter-independent stability in qualitatively heterogeneous passive networked systems containing damped and undamped nodes. Given the graph topology and a set of damped nodes, we ask if output consensus is achieved for all system parameter values. For given parameter

  16. Environmental Transport Input Parameters for the Biosphere Model

    Energy Technology Data Exchange (ETDEWEB)

    M. A. Wasiolek

    2003-06-27

    This analysis report is one of the technical reports documenting the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN), a biosphere model supporting the total system performance assessment (TSPA) for the geologic repository at Yucca Mountain. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows relationships among the reports developed for biosphere modeling and biosphere abstraction products for the TSPA, as identified in the ''Technical Work Plan: for Biosphere Modeling and Expert Support'' (TWP) (BSC 2003 [163602]). Some documents in Figure 1-1 may be under development and not available when this report is issued. This figure provides an understanding of how this report contributes to biosphere modeling in support of the license application (LA), but access to the listed documents is not required to understand the contents of this report. This report is one of the reports that develops input parameter values for the biosphere model. The ''Biosphere Model Report'' (BSC 2003 [160699]) describes the conceptual model, the mathematical model, and the input parameters. The purpose of this analysis is to develop biosphere model parameter values related to radionuclide transport and accumulation in the environment. These parameters support calculations of radionuclide concentrations in the environmental media (e.g., soil, crops, animal products, and air) resulting from a given radionuclide concentration at the source of contamination (i.e., either in groundwater or volcanic ash). The analysis was performed in accordance with the TWP (BSC 2003 [163602]). This analysis develops values of parameters associated with many features, events, and processes (FEPs) applicable to the reference biosphere (DTN: M00303SEPFEPS2.000 [162452]), which are addressed in the biosphere model (BSC 2003 [160699]). The treatment of these FEPs is described in BSC (2003 [160699

  17. Environmental Transport Input Parameters for the Biosphere Model

    International Nuclear Information System (INIS)

    Wasiolek, M. A.

    2003-01-01

    This analysis report is one of the technical reports documenting the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN), a biosphere model supporting the total system performance assessment (TSPA) for the geologic repository at Yucca Mountain. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows relationships among the reports developed for biosphere modeling and biosphere abstraction products for the TSPA, as identified in the ''Technical Work Plan: for Biosphere Modeling and Expert Support'' (TWP) (BSC 2003 [163602]). Some documents in Figure 1-1 may be under development and not available when this report is issued. This figure provides an understanding of how this report contributes to biosphere modeling in support of the license application (LA), but access to the listed documents is not required to understand the contents of this report. This report is one of the reports that develops input parameter values for the biosphere model. The ''Biosphere Model Report'' (BSC 2003 [160699]) describes the conceptual model, the mathematical model, and the input parameters. The purpose of this analysis is to develop biosphere model parameter values related to radionuclide transport and accumulation in the environment. These parameters support calculations of radionuclide concentrations in the environmental media (e.g., soil, crops, animal products, and air) resulting from a given radionuclide concentration at the source of contamination (i.e., either in groundwater or volcanic ash). The analysis was performed in accordance with the TWP (BSC 2003 [163602]). This analysis develops values of parameters associated with many features, events, and processes (FEPs) applicable to the reference biosphere (DTN: M00303SEPFEPS2.000 [162452]), which are addressed in the biosphere model (BSC 2003 [160699]). The treatment of these FEPs is described in BSC (2003 [160699], Section 6.2). Parameter values

  18. AN IMPROVED INTERFEROMETRIC CALIBRATION METHOD BASED ON INDEPENDENT PARAMETER DECOMPOSITION

    Directory of Open Access Journals (Sweden)

    J. Fan

    2018-04-01

    Full Text Available Interferometric SAR is sensitive to earth surface undulation. The accuracy of interferometric parameters plays a significant role in precise digital elevation model (DEM. The interferometric calibration is to obtain high-precision global DEM by calculating the interferometric parameters using ground control points (GCPs. However, interferometric parameters are always calculated jointly, making them difficult to decompose precisely. In this paper, we propose an interferometric calibration method based on independent parameter decomposition (IPD. Firstly, the parameters related to the interferometric SAR measurement are determined based on the three-dimensional reconstruction model. Secondly, the sensitivity of interferometric parameters is quantitatively analyzed after the geometric parameters are completely decomposed. Finally, each interferometric parameter is calculated based on IPD and interferometric calibration model is established. We take Weinan of Shanxi province as an example and choose 4 TerraDEM-X image pairs to carry out interferometric calibration experiment. The results show that the elevation accuracy of all SAR images is better than 2.54 m after interferometric calibration. Furthermore, the proposed method can obtain the accuracy of DEM products better than 2.43 m in the flat area and 6.97 m in the mountainous area, which can prove the correctness and effectiveness of the proposed IPD based interferometric calibration method. The results provide a technical basis for topographic mapping of 1 : 50000 and even larger scale in the flat area and mountainous area.

  19. Parameter uncertainty in CGE Modeling of the environmental impacts of economic policies

    International Nuclear Information System (INIS)

    Abler, D.G.; Shortle, J.S.; Rodriguez, A.G.

    1999-01-01

    This study explores the role of parameter uncertainty in Computable General Equilibrium (CGE) modeling of the environmental impacts of macroeconomic and sectoral policies, using Costa Rica as a case for study. A CGE model is constructed which includes eight environmental indicators covering deforestation, pesticides, overfishing, hazardous wastes, inorganic wastes, organic wastes, greenhouse gases, and air pollution. The parameters are treated as random variables drawn from prespecified distributions. Evaluation of each policy option consists of a Monte Carlo experiment. The impacts of the policy options on the environmental indicators are relatively robust to different parameter values, in spite of the wide range of parameter values employed. 33 refs

  20. Parameter uncertainty in CGE Modeling of the environmental impacts of economic policies

    Energy Technology Data Exchange (ETDEWEB)

    Abler, D.G.; Shortle, J.S. [Agricultural Economics, Pennsylvania State University, University Park, PA (United States); Rodriguez, A.G. [University of Costa Rica, San Jose (Costa Rica)

    1999-07-01

    This study explores the role of parameter uncertainty in Computable General Equilibrium (CGE) modeling of the environmental impacts of macroeconomic and sectoral policies, using Costa Rica as a case for study. A CGE model is constructed which includes eight environmental indicators covering deforestation, pesticides, overfishing, hazardous wastes, inorganic wastes, organic wastes, greenhouse gases, and air pollution. The parameters are treated as random variables drawn from prespecified distributions. Evaluation of each policy option consists of a Monte Carlo experiment. The impacts of the policy options on the environmental indicators are relatively robust to different parameter values, in spite of the wide range of parameter values employed. 33 refs.

  1. Reliability analysis of a sensitive and independent stabilometry parameter set.

    Science.gov (United States)

    Nagymáté, Gergely; Orlovits, Zsanett; Kiss, Rita M

    2018-01-01

    Recent studies have suggested reduced independent and sensitive parameter sets for stabilometry measurements based on correlation and variance analyses. However, the reliability of these recommended parameter sets has not been studied in the literature or not in every stance type used in stabilometry assessments, for example, single leg stances. The goal of this study is to evaluate the test-retest reliability of different time-based and frequency-based parameters that are calculated from the center of pressure (CoP) during bipedal and single leg stance for 30- and 60-second measurement intervals. Thirty healthy subjects performed repeated standing trials in a bipedal stance with eyes open and eyes closed conditions and in a single leg stance with eyes open for 60 seconds. A force distribution measuring plate was used to record the CoP. The reliability of the CoP parameters was characterized by using the intraclass correlation coefficient (ICC), standard error of measurement (SEM), minimal detectable change (MDC), coefficient of variation (CV) and CV compliance rate (CVCR). Based on the ICC, SEM and MDC results, many parameters yielded fair to good reliability values, while the CoP path length yielded the highest reliability (smallest ICC > 0.67 (0.54-0.79), largest SEM% = 19.2%). Usually, frequency type parameters and extreme value parameters yielded poor reliability values. There were differences in the reliability of the maximum CoP velocity (better with 30 seconds) and mean power frequency (better with 60 seconds) parameters between the different sampling intervals.

  2. Reliability analysis of a sensitive and independent stabilometry parameter set

    Science.gov (United States)

    Nagymáté, Gergely; Orlovits, Zsanett

    2018-01-01

    Recent studies have suggested reduced independent and sensitive parameter sets for stabilometry measurements based on correlation and variance analyses. However, the reliability of these recommended parameter sets has not been studied in the literature or not in every stance type used in stabilometry assessments, for example, single leg stances. The goal of this study is to evaluate the test-retest reliability of different time-based and frequency-based parameters that are calculated from the center of pressure (CoP) during bipedal and single leg stance for 30- and 60-second measurement intervals. Thirty healthy subjects performed repeated standing trials in a bipedal stance with eyes open and eyes closed conditions and in a single leg stance with eyes open for 60 seconds. A force distribution measuring plate was used to record the CoP. The reliability of the CoP parameters was characterized by using the intraclass correlation coefficient (ICC), standard error of measurement (SEM), minimal detectable change (MDC), coefficient of variation (CV) and CV compliance rate (CVCR). Based on the ICC, SEM and MDC results, many parameters yielded fair to good reliability values, while the CoP path length yielded the highest reliability (smallest ICC > 0.67 (0.54–0.79), largest SEM% = 19.2%). Usually, frequency type parameters and extreme value parameters yielded poor reliability values. There were differences in the reliability of the maximum CoP velocity (better with 30 seconds) and mean power frequency (better with 60 seconds) parameters between the different sampling intervals. PMID:29664938

  3. Environmental confounding in gene-environment interaction studies.

    Science.gov (United States)

    Vanderweele, Tyler J; Ko, Yi-An; Mukherjee, Bhramar

    2013-07-01

    We show that, in the presence of uncontrolled environmental confounding, joint tests for the presence of a main genetic effect and gene-environment interaction will be biased if the genetic and environmental factors are correlated, even if there is no effect of either the genetic factor or the environmental factor on the disease. When environmental confounding is ignored, such tests will in fact reject the joint null of no genetic effect with a probability that tends to 1 as the sample size increases. This problem with the joint test vanishes under gene-environment independence, but it still persists if estimating the gene-environment interaction parameter itself is of interest. Uncontrolled environmental confounding will bias estimates of gene-environment interaction parameters even under gene-environment independence, but it will not do so if the unmeasured confounding variable itself does not interact with the genetic factor. Under gene-environment independence, if the interaction parameter without controlling for the environmental confounder is nonzero, then there is gene-environment interaction either between the genetic factor and the environmental factor of interest or between the genetic factor and the unmeasured environmental confounder. We evaluate several recently proposed joint tests in a simulation study and discuss the implications of these results for the conduct of gene-environment interaction studies.

  4. Reactor parameters for European economic, safety and environmental studies

    International Nuclear Information System (INIS)

    Hancox, R.; Cooke, P.I.H.; Spears, W.R.

    1990-01-01

    Parameter sets for five 1200 MW e tokamak reactors were developed for the European Study Group on the Environmental, Safety-related and Economic Potential of Fusion Power, showing today's perception of the range of reactors likely to be available as a result of the Commission's fusion programme. On the basis of the cost of generating electricity, relative to a fission reactor, a reference set was chosen and endorsed by the Group for further studies including that on the environmental impact of fusion power. Key physics and technology parameters for the reference reactor are compared with values used in the ITER design, and with those from American studies. (author)

  5. An Independent Asteroseismic Analysis of the Fundamental Parameters and Internal Structure of the Solar-like Oscillator KIC 6225718

    Science.gov (United States)

    Wu, Tao; Li, Yan

    2017-09-01

    Asteroseismology is a useful tool that is usually used to probe stellar interiors and to determine stellar fundamental parameters, such as stellar mass, radius, and surface gravity. In order to probe stellar interiors, making comparisons between observations and models is usually used with the {χ }2-minimization method. The work of Wu & Li reported that the best parameter determined by the {χ }2-matching process is the acoustic radius for pure p-mode oscillations. In the present work, based on the theoretical calculations of Wu & Li, we will independently analyze the seismic observations of KIC 6225718 to determine its fundamental parameters and to investigate its interior properties. First, in order to test the method, we use it in the Sun to determine its fundamental parameters and to investigate interiors. Second, we independently determine the fundamental parameters of KIC 6225718 without any other non-seismic constraint. Therefore, those determined fundamental parameters are independent of those determined by other methods. They can be regarded as independent references in other analyses. Finally, we analyze the stellar internal structure and find that KIC 6225718 has a convective core with the size of 0.078-0.092 {R}⊙ . Its overshooting parameter {f}{ov} in the core is around 0.010. In addition, its center hydrogen {X}{{c}} is about 0.264-0.355.

  6. Influence of breed and environmental factors on litter parameters of ...

    African Journals Online (AJOL)

    Influence of breed and environmental factors on litter parameters of rabbits ... There was a non-significant effect of season on litter site at birth, kits alive at birth and ... to rabbit reproduction as it influenced negatively more litter parameters than ...

  7. Environmental monitoring and independent analysis: the experience of the local information commission in Cadarache

    International Nuclear Information System (INIS)

    Foucher, M.

    2010-01-01

    The 2006 Act on 'Open Access to Information and Nuclear Safety' provides free access to nuclear installations data and submits nuclear facilities to an independent administrative authority, the ASN (French Nuclear Safety Authority). A local information committee (CLI - Commission locale d'informations) has been set up for each nuclear facility. It includes all the parties involved and may commission expert studies and environmental measurement tests from independent laboratories. Prompted by environmental organizations, the Cadarache CLI commissioned a CRIIRAD (Commission de Recherche et d'Informations Independantes sur la Radioactivite) fact-finding survey in 2008-2009 to evaluate the environmental impact of the CEA/Cadarache installations since they were created. This study points to a moderate present impact, though a lack of data makes it impossible to reconstruct environmental impact prior to 1979. A set of guidelines are put forward to assess the past impact in greater detail and to lessen the current impact even further. Following this study, additional steps to minimize this impact will be taken by CEA/Cadarache inside the facilities, and by the relevant LCI outside the installations. Developing independent expert skills is a major challenge for CLIs to gain better knowledge of nuclear activities and improve their local management. (author)

  8. Agricultural and Environmental Input Parameters for the Biosphere Model

    International Nuclear Information System (INIS)

    Kaylie Rasmuson; Kurt Rautenstrauch

    2003-01-01

    This analysis is one of nine technical reports that support the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN) biosphere model. It documents input parameters for the biosphere model, and supports the use of the model to develop Biosphere Dose Conversion Factors (BDCF). The biosphere model is one of a series of process models supporting the Total System Performance Assessment (TSPA) for the repository at Yucca Mountain. The ERMYN provides the TSPA with the capability to perform dose assessments. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows the interrelationships between the major activities and their products (the analysis and model reports) that were planned in the biosphere Technical Work Plan (TWP, BSC 2003a). It should be noted that some documents identified in Figure 1-1 may be under development and therefore not available at the time this document is issued. The ''Biosphere Model Report'' (BSC 2003b) describes the ERMYN and its input parameters. This analysis report, ANL-MGR-MD-000006, ''Agricultural and Environmental Input Parameters for the Biosphere Model'', is one of the five reports that develop input parameters for the biosphere model. This report defines and justifies values for twelve parameters required in the biosphere model. These parameters are related to use of contaminated groundwater to grow crops. The parameter values recommended in this report are used in the soil, plant, and carbon-14 submodels of the ERMYN

  9. Linear least squares compartmental-model-independent parameter identification in PET

    International Nuclear Information System (INIS)

    Thie, J.A.; Smith, G.T.; Hubner, K.F.

    1997-01-01

    A simplified approach involving linear-regression straight-line parameter fitting of dynamic scan data is developed for both specific and nonspecific models. Where compartmental-model topologies apply, the measured activity may be expressed in terms of: its integrals, plasma activity and plasma integrals -- all in a linear expression with macroparameters as coefficients. Multiple linear regression, as in spreadsheet software, determines parameters for best data fits. Positron emission tomography (PET)-acquired gray-matter images in a dynamic scan are analyzed: both by this method and by traditional iterative nonlinear least squares. Both patient and simulated data were used. Regression and traditional methods are in expected agreement. Monte-Carlo simulations evaluate parameter standard deviations, due to data noise, and much smaller noise-induced biases. Unique straight-line graphical displays permit visualizing data influences on various macroparameters as changes in slopes. Advantages of regression fitting are: simplicity, speed, ease of implementation in spreadsheet software, avoiding risks of convergence failures or false solutions in iterative least squares, and providing various visualizations of the uptake process by straight line graphical displays. Multiparameter model-independent analyses on lesser understood systems is also made possible

  10. Agricultural and Environmental Input Parameters for the Biosphere Model

    Energy Technology Data Exchange (ETDEWEB)

    Kaylie Rasmuson; Kurt Rautenstrauch

    2003-06-20

    This analysis is one of nine technical reports that support the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN) biosphere model. It documents input parameters for the biosphere model, and supports the use of the model to develop Biosphere Dose Conversion Factors (BDCF). The biosphere model is one of a series of process models supporting the Total System Performance Assessment (TSPA) for the repository at Yucca Mountain. The ERMYN provides the TSPA with the capability to perform dose assessments. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows the interrelationships between the major activities and their products (the analysis and model reports) that were planned in the biosphere Technical Work Plan (TWP, BSC 2003a). It should be noted that some documents identified in Figure 1-1 may be under development and therefore not available at the time this document is issued. The ''Biosphere Model Report'' (BSC 2003b) describes the ERMYN and its input parameters. This analysis report, ANL-MGR-MD-000006, ''Agricultural and Environmental Input Parameters for the Biosphere Model'', is one of the five reports that develop input parameters for the biosphere model. This report defines and justifies values for twelve parameters required in the biosphere model. These parameters are related to use of contaminated groundwater to grow crops. The parameter values recommended in this report are used in the soil, plant, and carbon-14 submodels of the ERMYN.

  11. Models and parameters for environmental radiological assessments

    International Nuclear Information System (INIS)

    Miller, C.W.

    1983-01-01

    This article reviews the forthcoming book Models and Parameters for Environmental Radiological Assessments, which presents a unified compilation of models and parameters for assessing the impact on man of radioactive discharges, both routine and accidental, into the environment. Models presented in this book include those developed for the prediction of atmospheric and hydrologic transport and deposition, for terrestrial and aquatic food-chain bioaccumulation, and for internal and external dosimetry. Summaries are presented for each of the transport and dosimetry areas previously for each of the transport and dosimetry areas previously mentioned, and details are available in the literature cited. A chapter of example problems illustrates many of the methodologies presented throughout the text. Models and parameters presented are based on the results of extensive literature reviews and evaluations performed primarily by the staff of the Health and Safety Research Division of Oak Ridge National Laboratory

  12. Environmental Transport Input Parameters for the Biosphere Model

    International Nuclear Information System (INIS)

    M. Wasiolek

    2004-01-01

    This analysis report is one of the technical reports documenting the Environmental Radiation Model for Yucca Mountain, Nevada (ERMYN), a biosphere model supporting the total system performance assessment for the license application (TSPA-LA) for the geologic repository at Yucca Mountain. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows relationships among the reports developed for biosphere modeling and biosphere abstraction products for the TSPA-LA, as identified in the ''Technical Work Plan for Biosphere Modeling and Expert Support'' (BSC 2004 [DIRS 169573]) (TWP). This figure provides an understanding of how this report contributes to biosphere modeling in support of the license application (LA). This report is one of the five reports that develop input parameter values for the biosphere model. The ''Biosphere Model Report'' (BSC 2004 [DIRS 169460]) describes the conceptual model and the mathematical model. The input parameter reports, shown to the right of the Biosphere Model Report in Figure 1-1, contain detailed description of the model input parameters. The output of this report is used as direct input in the ''Nominal Performance Biosphere Dose Conversion Factor Analysis'' and in the ''Disruptive Event Biosphere Dose Conversion Factor Analysis'' that calculate the values of biosphere dose conversion factors (BDCFs) for the groundwater and volcanic ash exposure scenarios, respectively. The purpose of this analysis was to develop biosphere model parameter values related to radionuclide transport and accumulation in the environment. These parameters support calculations of radionuclide concentrations in the environmental media (e.g., soil, crops, animal products, and air) resulting from a given radionuclide concentration at the source of contamination (i.e., either in groundwater or in volcanic ash). The analysis was performed in accordance with the TWP (BSC 2004 [DIRS 169573])

  13. Environmental Transport Input Parameters for the Biosphere Model

    Energy Technology Data Exchange (ETDEWEB)

    M. Wasiolek

    2004-09-10

    This analysis report is one of the technical reports documenting the Environmental Radiation Model for Yucca Mountain, Nevada (ERMYN), a biosphere model supporting the total system performance assessment for the license application (TSPA-LA) for the geologic repository at Yucca Mountain. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows relationships among the reports developed for biosphere modeling and biosphere abstraction products for the TSPA-LA, as identified in the ''Technical Work Plan for Biosphere Modeling and Expert Support'' (BSC 2004 [DIRS 169573]) (TWP). This figure provides an understanding of how this report contributes to biosphere modeling in support of the license application (LA). This report is one of the five reports that develop input parameter values for the biosphere model. The ''Biosphere Model Report'' (BSC 2004 [DIRS 169460]) describes the conceptual model and the mathematical model. The input parameter reports, shown to the right of the Biosphere Model Report in Figure 1-1, contain detailed description of the model input parameters. The output of this report is used as direct input in the ''Nominal Performance Biosphere Dose Conversion Factor Analysis'' and in the ''Disruptive Event Biosphere Dose Conversion Factor Analysis'' that calculate the values of biosphere dose conversion factors (BDCFs) for the groundwater and volcanic ash exposure scenarios, respectively. The purpose of this analysis was to develop biosphere model parameter values related to radionuclide transport and accumulation in the environment. These parameters support calculations of radionuclide concentrations in the environmental media (e.g., soil, crops, animal products, and air) resulting from a given radionuclide concentration at the source of contamination (i.e., either in groundwater or in volcanic ash). The analysis

  14. Operating performance and environmental and safety risks: A preliminary comparison of majors and independents

    International Nuclear Information System (INIS)

    Pulsipher, A.G.; Iledare, W.O.; Baumann, R.H.; Mesyanzhinov, D.

    1995-01-01

    The objective is to compare the safety and environmental records of oil and gas companies operating on the OCS in the Gulf of Mexico over the past decade. The reason for doing so is to help inform public sector policy-makers and private sector decision-makers about the potential safety and environmental risks associated with the expected increased presence of smaller independents in the domestic oil and gas industry in general and on the federal OCS in particular. The preliminary conclusion is that although independents have had a modestly high incidence of fires and explosions than the majors, the difference is not significant statistically and is largely attributable to a few ''bad actors'' rather than demonstrably poorer practice by the group as a whole

  15. Report on site-independent environmental impacts of radioactive waste storage and management

    International Nuclear Information System (INIS)

    1985-10-01

    The organisation responsible for radioactive wastes in the Netherlands is COVRA: Centrale Organisatie Voor Radioactief Afval. It deals especially with storage and management of these wastes. For that purpose, COVRA will build a waste managing and storage facility at a central site in the Netherlands. In this report, environmental impacts of these activities are studied, that are independent of the location. The report is readable and useful for a broad audience. In the main report, the general features are outlined starting from figures and tables on environmental effects. In a separate volume, detailed numerical data are presented. (G.J.P.)

  16. Key processes and input parameters for environmental tritium models

    International Nuclear Information System (INIS)

    Bunnenberg, C.; Taschner, M.; Ogram, G.L.

    1994-01-01

    The primary objective of the work reported here is to define key processes and input parameters for mathematical models of environmental tritium behaviour adequate for use in safety analysis and licensing of fusion devices like NET and associated tritium handling facilities. (author). 45 refs., 3 figs

  17. Key processes and input parameters for environmental tritium models

    Energy Technology Data Exchange (ETDEWEB)

    Bunnenberg, C; Taschner, M [Niedersaechsisches Inst. fuer Radiooekologie, Hannover (Germany); Ogram, G L [Ontario Hydro, Toronto, ON (Canada)

    1994-12-31

    The primary objective of the work reported here is to define key processes and input parameters for mathematical models of environmental tritium behaviour adequate for use in safety analysis and licensing of fusion devices like NET and associated tritium handling facilities. (author). 45 refs., 3 figs.

  18. Agricultural and Environmental Input Parameters for the Biosphere Model

    Energy Technology Data Exchange (ETDEWEB)

    K. Rasmuson; K. Rautenstrauch

    2004-09-14

    This analysis is one of 10 technical reports that support the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN) (i.e., the biosphere model). It documents development of agricultural and environmental input parameters for the biosphere model, and supports the use of the model to develop biosphere dose conversion factors (BDCFs). The biosphere model is one of a series of process models supporting the total system performance assessment (TSPA) for the repository at Yucca Mountain. The ERMYN provides the TSPA with the capability to perform dose assessments. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows the interrelationships between the major activities and their products (the analysis and model reports) that were planned in ''Technical Work Plan for Biosphere Modeling and Expert Support'' (BSC 2004 [DIRS 169573]). The ''Biosphere Model Report'' (BSC 2004 [DIRS 169460]) describes the ERMYN and its input parameters.

  19. Agricultural and Environmental Input Parameters for the Biosphere Model

    International Nuclear Information System (INIS)

    K. Rasmuson; K. Rautenstrauch

    2004-01-01

    This analysis is one of 10 technical reports that support the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN) (i.e., the biosphere model). It documents development of agricultural and environmental input parameters for the biosphere model, and supports the use of the model to develop biosphere dose conversion factors (BDCFs). The biosphere model is one of a series of process models supporting the total system performance assessment (TSPA) for the repository at Yucca Mountain. The ERMYN provides the TSPA with the capability to perform dose assessments. A graphical representation of the documentation hierarchy for the ERMYN is presented in Figure 1-1. This figure shows the interrelationships between the major activities and their products (the analysis and model reports) that were planned in ''Technical Work Plan for Biosphere Modeling and Expert Support'' (BSC 2004 [DIRS 169573]). The ''Biosphere Model Report'' (BSC 2004 [DIRS 169460]) describes the ERMYN and its input parameters

  20. An indicator for effects of organic toxicants on lotic invertebrate communities: Independence of confounding environmental factors over an extensive river continuum

    International Nuclear Information System (INIS)

    Beketov, Mikhail A.; Liess, Matthias

    2008-01-01

    Distinguishing between effects of natural and anthropogenic environmental factors on ecosystems is a fundamental problem in environmental science. In river systems the longitudinal gradient of environmental factors is one of the most relevant sources of dissimilarity between communities that could be confounded with anthropogenic disturbances. To test the hypothesis that in macroinvertebrate communities the distribution of species' sensitivity to organic toxicants is independent of natural longitudinal factors, but depends on contamination with organic toxicants, we analysed the relationship between community sensitivity SPEAR organic (average community sensitivity to organic toxicants) and natural and anthropogenic environmental factors in a large-scale river system, from alpine streams to a lowland river. The results show that SPEAR organic is largely independent of natural longitudinal factors, but strongly dependent on contamination with organic toxicants (petrochemicals and synthetic surfactants). Usage of SPEAR organic as a stressor-specific longitude-independent measure will facilitate detection of community disturbance by organic toxicants. - Indicator for organic toxicants at community level can be independent of natural environmental factors

  1. The Carlsbad Environmental Monitoring and Research Center: An independent program for community information

    International Nuclear Information System (INIS)

    Fingleton, Donald J.; Bhada, Ron K.; Derald Morgan, J.; Julien, Howard

    1992-01-01

    The Waste Isolation Pilot Plant (WIPP) was designed and built as a research and development facility to obtain data to demonstrate the safe management, storage, and disposal of defense-related transuranic (TRU) waste. The WIPP facility, near Carlsbad, New Mexico, is scheduled to receive its first shipment of TRU waste in 1992. The citizens of Carlsbad requested the U.S. Department of Energy (DOE) to provide them with an independent organization that would monitor the entire area with state-of-the-art monitoring techniques and publish the data. As a follow-up, the DOE approved a proposal from the Waste-management Education and Research Consortium of New Mexico to develop and implement this program. The purpose of this paper is to (1) describe this innovative program to establish the Carlsbad Environmental Monitoring and Research Center, an independent university based center to study health and environmental impacts associated with technological development; (2) present the Center's mission and objectives; and (3) give an overview of the progress. (author)

  2. Influence of Environmental Parameters on Trichoderma Strains with Biocontrol Potential

    Directory of Open Access Journals (Sweden)

    Zsuzsanna Antal

    2003-01-01

    Full Text Available Several mycoparasitic strains belonging to the filamentous fungal genus Trichoderma are promising candidates for the biological control of plant pathogenic fungi. When planning the application of antagonistic Trichoderma strains for the purposes of biological control, it is very important to consider the environmental parameters affecting the biocontrol agents in the soil. A series of abiotic and biotic environmental parameters has an influence on the biocontrol efficacy of Trichoderma. Some important parameters to be considered are the effects of temperature, water potential and pH, and the presence of pesticides, metal ions and antagonistic bacteria in the soil. Most of the Trichoderma strains are mesophilic. Low temperatures in winter may cause a problem during biological control by influencing the activity of the biocontrol agents. Another problem emerging during the application of Trichoderma strains as biocontrol agents is that they cannot tolerate dry conditions, however, we may need biocontrol agents against plant pathogenic fungi which are able to grow and cause disease even in dry soils. The pH characteristics of the soil also belong to the most important environmental parameters affecting the activities of mycoparasitic Trichoderma strains. Within the frames of a complex integrated plant protection strategy, we may have to combine Trichoderma strains with chemical pesticides or metal compounds, therefore it is important to collect information about the effects of pesticides and metal ions on the biocontrol strains. Antagonistic soil bacteria may also have negative effects on the biocontrol abilities of Trichoderma strains, therefore it may be advantageous if a biocontrol strain possesses bacterium- degrading abilities as well. This review will discuss the literature about the influence of temperature, water potential, pH, pesticides, metal ions and antagonistic bacteria on mycoparasitic Trichoderma strains including the results of our

  3. Environmental parameters series. 3. Concentration factors of radionuclides in freshwater organisms

    International Nuclear Information System (INIS)

    1994-03-01

    This report outlines recent research activities of Radioactive Waste Management Center. Aiming to estimate the radiation dose of man exposed to radioactive materials in an environment, construction of a calculation model on the transfer of radionuclide in the environment was attempted. This issue, Environmental parameter series No.3 includes six reports on the factors related to environmental concentration for radionuclides. The title of the reports are as follows; Factors modifying the concentration factor (CF), Evaluation of accumulation of radionuclides in brackish water organisms, Dose assessment, CF derived from Japanese limnological data, Data table of CF and Metabolic parameters in relation to bioaccumulation of elements by organisms. In addition to collect and arrange the existing data, CF was calculated based on the concentration of stable elements in various lakes and rivers in Japan. (M.N.)

  4. Lumped parameter models for the interpretation of environmental tracer data

    Energy Technology Data Exchange (ETDEWEB)

    Maloszewski, P [GSF-Inst. for Hydrology, Oberschleissheim (Germany); Zuber, A [Institute of Nuclear Physics, Cracow (Poland)

    1996-10-01

    Principles of the lumped-parameter approach to the interpretation of environmental tracer data are given. The following models are considered: the piston flow model (PFM), exponential flow model (EM), linear model (LM), combined piston flow and exponential flow model (EPM), combined linear flow and piston flow model (LPM), and dispersion model (DM). The applicability of these models for the interpretation of different tracer data is discussed for a steady state flow approximation. Case studies are given to exemplify the applicability of the lumped-parameter approach. Description of a user-friendly computer program is given. (author). 68 refs, 25 figs, 4 tabs.

  5. Lumped parameter models for the interpretation of environmental tracer data

    International Nuclear Information System (INIS)

    Maloszewski, P.; Zuber, A.

    1996-01-01

    Principles of the lumped-parameter approach to the interpretation of environmental tracer data are given. The following models are considered: the piston flow model (PFM), exponential flow model (EM), linear model (LM), combined piston flow and exponential flow model (EPM), combined linear flow and piston flow model (LPM), and dispersion model (DM). The applicability of these models for the interpretation of different tracer data is discussed for a steady state flow approximation. Case studies are given to exemplify the applicability of the lumped-parameter approach. Description of a user-friendly computer program is given. (author). 68 refs, 25 figs, 4 tabs

  6. Environmental parameters linked to the last migratory stage of barnacle geese en route to their breeding sites

    NARCIS (Netherlands)

    Najafabadi, M.S.; Darvishzadeh, R.; Skidmore, A.K.; Kölzsch, Andrea; Exo, Klaus-Michael; Nolet, Bart A.; Griffin, Larry; Stahl, Julia; Havinga, Paul J.M.; Meratnia, Nirvana; Toxopeus, A.G.

    The migration timing of birds can be controlled by endogenous parameters. However, little is known about how environmental parameters influence the timing of migration and which have the greatest influence at different stages of migration. In this study we identified the main environmental

  7. Environmental parameters linked to the last migratory stage of barnacle geese en route to their breeding sites

    NARCIS (Netherlands)

    Shariati Najafabadi, Mitra; Darvishzadeh, Roshanak; Skidmore, A.K.; Kölzsch, A.; Exo, K-M.; Nolet, B.A.; Griffin, L.; Stahl, J.; Havinga, Paul J.M.; Meratnia, Nirvana; Toxopeus, A.G.

    2016-01-01

    The migration timing of birds can be controlled by endogenous parameters. However, little is known about how environmental parameters influence the timing of migration and which have the greatest influence at different stages of migration. In this study we identified the main environmental

  8. The influence of demographic, environmental and physical factors on functional independence post stroke

    Directory of Open Access Journals (Sweden)

    M.V. Mamabolo

    2008-01-01

    Full Text Available Purpose: The magnitude of disability observed in strokesurvivors is believed to be dependent in part, on the severity of neurological deficits incurred. A s important but less well understood, is thecontribution of demographic, physical and environmental factors. The objective of this study was to establish what demographic, environmentaland physical factors influence functional independence post stroke. Method: Convenience sampling was used in the selection of subjects from four stroke outpatient public health facilities in the Gauteng Province of South Africa. The data were collected using a structured questionnaire. The analytical tools used included descriptive statistics to measure percentages and cross tabulations to measure the level of associations between functional independence and some of the demographic factors. The Barthel Index was computed to establish the degree of functional independence. Finally the influence of factors on functional independence was investigated using bivariate logistic regressions.Results: The results showed that younger patients (18 - 34 yrs may have a higher likelihood of functional independence compared to older patients at the time of discharge from hospital (18 - 34 years: Odds Ratio = 1. Patients without helpers were more likely to be functionally independent than those with a helper (p = 0.03. Involvement in household activities (p = 0.01, participation in community activities (p = 0.02 and bowel and bladder continence (p = 0.003 and p = 0.04 improved the likelihood of functional independence.Conclusion and im plications: Factors that influence functional independence post stroke are: age, bowel and bladder continence, the presence of a caregiver, participation in household and community activities. It is also of value to encourage patients to participate in household and community activities post stroke as well as being less dependent on helpers in an effort to attain functional independence post

  9. Recommended environmental dose calculation methods and Hanford-specific parameters

    International Nuclear Information System (INIS)

    Schreckhise, R.G.; Rhoads, K.; Napier, B.A.; Ramsdell, J.V.; Davis, J.S.

    1993-03-01

    This document was developed to support the Hanford Environmental Dose overview Panel (HEDOP). The Panel is responsible for reviewing all assessments of potential doses received by humans and other biota resulting from the actual or possible environmental releases of radioactive and other hazardous materials from facilities and/or operations belonging to the US Department of Energy on the Hanford Site in south-central Washington. This document serves as a guide to be used for developing estimates of potential radiation doses, or other measures of risk or health impacts, to people and other biota in the environs on and around the Hanford Site. It provides information to develop technically sound estimates of exposure (i.e., potential or actual) to humans or other biotic receptors that could result from the environmental transport of potentially harmful materials that have been, or could be, released from Hanford operations or facilities. Parameter values and information that are specific to the Hanford environs as well as other supporting material are included in this document

  10. Recommended environmental dose calculation methods and Hanford-specific parameters

    Energy Technology Data Exchange (ETDEWEB)

    Schreckhise, R.G.; Rhoads, K.; Napier, B.A.; Ramsdell, J.V. (Pacific Northwest Lab., Richland, WA (United States)); Davis, J.S. (Westinghouse Hanford Co., Richland, WA (United States))

    1993-03-01

    This document was developed to support the Hanford Environmental Dose overview Panel (HEDOP). The Panel is responsible for reviewing all assessments of potential doses received by humans and other biota resulting from the actual or possible environmental releases of radioactive and other hazardous materials from facilities and/or operations belonging to the US Department of Energy on the Hanford Site in south-central Washington. This document serves as a guide to be used for developing estimates of potential radiation doses, or other measures of risk or health impacts, to people and other biota in the environs on and around the Hanford Site. It provides information to develop technically sound estimates of exposure (i.e., potential or actual) to humans or other biotic receptors that could result from the environmental transport of potentially harmful materials that have been, or could be, released from Hanford operations or facilities. Parameter values and information that are specific to the Hanford environs as well as other supporting material are included in this document.

  11. Relationship between bacterial diversity and environmental parameters during composting of different raw materials.

    Science.gov (United States)

    Wang, Xueqin; Cui, Hongyang; Shi, Jianhong; Zhao, Xinyu; Zhao, Yue; Wei, Zimin

    2015-12-01

    The aim of this study was to compare the bacterial structure of seven different composts. The primary environmental factors affecting bacterial species were identified, and a strategy to enhance the abundance of uncultured bacteria through controlling relevant environmental parameters was proposed. The results showed that the physical-chemical parameters of each different pile changed in its own manner during composting, which affected the structure and succession of bacteria in different ways. DGGE profiles showed that there were 10 prominent species during composting. Among them, four species existed in all compost types, two species existed in several piles and four species were detected in a single material. Redundancy analysis results showed that bacterial species compositions were significantly influenced by C/N and moisture (p<0.05). The optimal range of C/N was 14-27. Based on these results, the primary environmental factors affecting a certain species were further identified as a potential control of bacterial diversity. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

    Energy Technology Data Exchange (ETDEWEB)

    Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

    1987-09-01

    This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs.

  13. Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

    International Nuclear Information System (INIS)

    Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

    1987-09-01

    This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs

  14. Inexpensive, Open-Source, Internet of Things-Enabled Sensing Stations for Environmental Parameter Measurements

    Science.gov (United States)

    Marchetto, P. M.; Hofmeister, K.; Walter, M. T.

    2015-12-01

    In the age of the Internet, data is inherently portable. Given the shrinking numbers of stream gauges in the US under the banner of the USGS and the lack of collocation of sensors for environmental parameters, it is clear the only way to collect these data is with near real-time, multi-parameters sensing stations. We are designing a system that can be built and deployed for under $300 by community groups interested in learning more about the land that they are protecting, such as conservation groups, or groups interested in the basic science behind sensing and ecology, such as makerspaces. Sensing stations like these will enable a greater diversity of data collection while increasing public awareness of environmental issues and the research process.

  15. Sensitivity analysis of specific activity model parameters for environmental transport of 3H and dose assessment

    International Nuclear Information System (INIS)

    Rout, S.; Mishra, D.G.; Ravi, P.M.; Tripathi, R.M.

    2016-01-01

    Tritium is one of the radionuclides likely to get released to the environment from Pressurized Heavy Water Reactors. Environmental models are extensively used to quantify the complex environmental transport processes of radionuclides and also to assess the impact to the environment. Model parameters exerting the significant influence on model results are identified through a sensitivity analysis (SA). SA is the study of how the variation (uncertainty) in the output of a mathematical model can be apportioned, qualitatively or quantitatively, to different sources of variation in the input parameters. This study was designed to identify the sensitive model parameters of specific activity model (TRS 1616, IAEA) for environmental transfer of 3 H following release to air and then to vegetation and animal products. Model includes parameters such as air to soil transfer factor (CRs), Tissue Free Water 3 H to Organically Bound 3 H ratio (Rp), Relative humidity (RH), WCP (fractional water content) and WEQp (water equivalent factor) any change in these parameters leads to change in 3 H level in vegetation and animal products consequently change in dose due to ingestion. All these parameters are function of climate and/or plant which change with time, space and species. Estimation of these parameters at every time is a time consuming and also required sophisticated instrumentation. Therefore it is necessary to identify the sensitive parameters and freeze the values of least sensitive parameters at constant values for more accurate estimation of 3 H dose in short time for routine assessment

  16. Interdependence of environmental parameters and sand dwelling benthic species abundance: a multivariate approach

    Digital Repository Service at National Institute of Oceanography (India)

    Harkantra, S.N.; Parulekar, A.H.

    Multivariate analysis showed dependence of distribution and abundance of sand dwelling fauna on more than one ecologically significant environmental parameters rather than one ecological master factor. Salinity, grain size, beach gradient, dissolved...

  17. Selected environmental considerations and their measuring parameters for nuclear power plant siting

    International Nuclear Information System (INIS)

    Norris, J.A.

    1975-01-01

    The site selection process for nuclear power stations encompasses a broad range of considerations. A categorization of these considerations consistent with the needs of the U. S. Atomic Energy Commission, as the regulatory agency, and of the utility company involves these major areas of concern. They are issues related to safety, environmental impact, and engineering/economics. The more important environmental considerations and their measuring parameters presented in this paper include biota, ecological systems and water quality, land use, aesthetics, water availability, and meteorology. (U.S.)

  18. Human comfort and self-estimated performance in relation to indoor environmental parameters and building features

    DEFF Research Database (Denmark)

    Frontczak, Monika Joanna

    The main objective of the Ph.D. study was to examine occupants’ perception of comfort and self-estimated job performance in non-industrial buildings (homes and offices), in particular how building occupants understand comfort and which parameters, not necessarily related to indoor environments...... and storage, noise level and visual privacy. However, if job performance is considered, then satisfaction with the main indoor environmental parameters should be addressed first as they affected self-estimated job performance to the highest extent. The present study showed that overall satisfaction...... with personal workspace affected significantly the self-estimated job performance. Increasing overall satisfaction with the personal workspace by about 15% would correspond to an increase of self-estimated job performance by 3.7%. Among indoor environmental parameters and building features, satisfaction...

  19. Evaluation of water quality parameters and associated environmental impact at nuclear power plant sites

    International Nuclear Information System (INIS)

    Joshi, M.L.; Hegde, A.G.

    2005-01-01

    The Nuclear Power Plants use a large quantity of water for the purpose of cooling the turbine condenser. The heated effluents are discharged to aquatic environment by means of once through cooling wherever large water bodies like seacoast or fresh water reservoir are available. The quality of water bodies are important for the growth and biodiversity of aquatic organisms. Several environmental factors like Temperature pH, Dissolved Oxygen have a bearing on the life cycle of aquatic organisms. The paper describes the evaluation of water quality parameters at the two typical sites one on the sea coast (Tarapur) and other at inland site Kaiga and discusses the environmental impact due to discharge to aquatic environment. It is found that the environmental impacts due to both heated effluents and radioactivity are insignificant. The water quality parameters are found to be well within the prescribed standards. (author)

  20. Independent technical review of the Sandia National Laboratories Environmental Restoration Project

    International Nuclear Information System (INIS)

    1994-11-01

    An Independent Technical Review was conducted of the Environmental Restoration Project. The objective of the review was recommendations, from a commercial perspective, on a systems level path forward to safe, minimum cost and schedule project completion. The work presented represents the consensus analysis and recommendations of thirteen individuals with varied backgrounds, expertise, and experience. The ITR team recommends that the barriers to the opportunity described in the diagnosis be eliminated using an integrated DOE-Sandia system approach. Piecemeal changes will not result in the desired commercial efficiency. DOE needs to operate as the contracting agency for a Major System Acquisition. If it does not, commercial performance will not be achieved regardless of the contractor. Likewise, Sandia needs to establish and implement the necessary project structure and management systems to operate with commercial contractor like efficiency

  1. Approaches in highly parameterized inversion—PEST++ Version 3, a Parameter ESTimation and uncertainty analysis software suite optimized for large environmental models

    Science.gov (United States)

    Welter, David E.; White, Jeremy T.; Hunt, Randall J.; Doherty, John E.

    2015-09-18

    The PEST++ Version 1 object-oriented parameter estimation code is here extended to Version 3 to incorporate additional algorithms and tools to further improve support for large and complex environmental modeling problems. PEST++ Version 3 includes the Gauss-Marquardt-Levenberg (GML) algorithm for nonlinear parameter estimation, Tikhonov regularization, integrated linear-based uncertainty quantification, options of integrated TCP/IP based parallel run management or external independent run management by use of a Version 2 update of the GENIE Version 1 software code, and utilities for global sensitivity analyses. The Version 3 code design is consistent with PEST++ Version 1 and continues to be designed to lower the barriers of entry for users as well as developers while providing efficient and optimized algorithms capable of accommodating large, highly parameterized inverse problems. As such, this effort continues the original focus of (1) implementing the most popular and powerful features of the PEST software suite in a fashion that is easy for novice or experienced modelers to use and (2) developing a software framework that is easy to extend.

  2. On the temperature independence of statistical model parameters for cleavage fracture in ferritic steels

    Science.gov (United States)

    Qian, Guian; Lei, Wei-Sheng; Niffenegger, M.; González-Albuixech, V. F.

    2018-04-01

    The work relates to the effect of temperature on the model parameters in local approaches (LAs) to cleavage fracture. According to a recently developed LA model, the physical consensus of plastic deformation being a prerequisite to cleavage fracture enforces any LA model of cleavage fracture to observe initial yielding of a volume element as its threshold stress state to incur cleavage fracture in addition to the conventional practice of confining the fracture process zone within the plastic deformation zone. The physical consistency of the new LA model to the basic LA methodology and the differences between the new LA model and other existing models are interpreted. Then this new LA model is adopted to investigate the temperature dependence of LA model parameters using circumferentially notched round tensile specimens. With the published strength data as input, finite element (FE) calculation is conducted for elastic-perfectly plastic deformation and the realistic elastic-plastic hardening, respectively, to provide stress distributions for model calibration. The calibration results in temperature independent model parameters. This leads to the establishment of a 'master curve' characteristic to synchronise the correlation between the nominal strength and the corresponding cleavage fracture probability at different temperatures. This 'master curve' behaviour is verified by strength data from three different steels, providing a new path to calculate cleavage fracture probability with significantly reduced FE efforts.

  3. Recommended environmental dose calculation methods and Hanford-specific parameters. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    Schreckhise, R.G.; Rhoads, K.; Napier, B.A.; Ramsdell, J.V. [Pacific Northwest Lab., Richland, WA (United States); Davis, J.S. [Westinghouse Hanford Co., Richland, WA (United States)

    1993-03-01

    This document was developed to support the Hanford Environmental Dose overview Panel (HEDOP). The Panel is responsible for reviewing all assessments of potential doses received by humans and other biota resulting from the actual or possible environmental releases of radioactive and other hazardous materials from facilities and/or operations belonging to the US Department of Energy on the Hanford Site in south-central Washington. This document serves as a guide to be used for developing estimates of potential radiation doses, or other measures of risk or health impacts, to people and other biota in the environs on and around the Hanford Site. It provides information to develop technically sound estimates of exposure (i.e., potential or actual) to humans or other biotic receptors that could result from the environmental transport of potentially harmful materials that have been, or could be, released from Hanford operations or facilities. Parameter values and information that are specific to the Hanford environs as well as other supporting material are included in this document.

  4. Satisfaction and self-estimated performance in relation to indoor environmental parameters and building features

    DEFF Research Database (Denmark)

    Wargocki, Pawel; Frontczak, Monika; Schiavon, Stefano

    2012-01-01

    The paper examines how satisfaction with indoor environmental parameters and building features affects satisfaction and self-estimated job performance. The analyses used subjective responses from around 50, 000 occupants collected mainly in US office buildings using a web-based survey administered...

  5. Headache symptoms and indoor environmental parameters: Results from the EPA BASE study

    Directory of Open Access Journals (Sweden)

    Gretchen E Tietjen

    2012-01-01

    Full Text Available Objective: The objective of this investigation was to determine the prevalence of migraine and headache symptoms in a national sample of US office employees. Also, we explored the association of headache symptoms with indoor environmental parameters of the work place. Background: Sick building syndrome (SBS, which includes headache, is a common global phenomenon, but the underlying environmental cause is uncertain. Materials and Methods: We used data from the 1994-1998 US Environmental Protection Agency′s (EPA Building Assessment and Survey Evaluation, a cross-sectional study of workers employed in 100 public and private office buildings across 25 states. The study used a self-administered questionnaire to assess headache frequency and prevalence of self-reported physician-diagnosed (SRPD migraine. Indoor environmental parameters (IEP were collected per EPA protocol from each building over a 1-week period and included carbon dioxide, carbon monoxide, temperature, relative humidity, particulate matter, volatile organic compound, illuminance, and sound level. The standards of American Society of Heating, Refrigerating and Air Conditioning Engineers were used to categorize IEP as either within- or out-of-comfort range for human dwelling. These limits delineate whether a parameter value is safe for human dwelling. Out-of-comfort range IEPs are associated with SBS and other human diseases. SRPD migraine and headache frequency were the primary outcome measures of the study. Multivariate logistic regression analyses were employed for the purpose of assessing the association between the outcome variable and IEPs. Results: Of the 4326 participants, 66% were females and 60% were between 30 and 49 years. Headache frequency during the last 4 weeks was as follows: None in 31%, 1-3 days in 38%, 1-3 days per week in 18%, and every or almost every workday in 8%. Females had higher SRPD migraine prevalence compared to males (27% vs. 11%, P<0.001 and were more

  6. Human comfort and self-estimated performance in relation to indoor environmental parameters and building features

    OpenAIRE

    Frontczak, Monika Joanna; Wargocki, Pawel

    2011-01-01

    The main objective of the Ph.D. study was to examine occupants’ perception of comfort and self-estimated job performance in non-industrial buildings (homes and offices), in particular how building occupants understand comfort and which parameters, not necessarily related to indoor environments, influence the perception of comfort.To meet the objective, the following actions were taken: (1) a literature survey exploring which indoor environmental parameters (thermal, acoustic, visualenvironmen...

  7. Preliminary study of environmental parameters associated with the feasibility of a polygeneration plant at Kennedy Space Center

    International Nuclear Information System (INIS)

    Barnes, G.D.

    1982-01-01

    The feasibility of a polygeneration plant at Kennedy Space Center was studied. Liquid hydrogen and gaseous nitrogen are the two principal products in consideration. Environmental parameters (air quality, water quality, biological diversity and hazardous waste disposal) necessary for the feasibility study were investigated. A National Environmental Policy Act (NEPA) project flow sheet was to be formulated for the environmental impact statement. Water quality criteria for Florida waters were to be established

  8. Model calibration and parameter estimation for environmental and water resource systems

    CERN Document Server

    Sun, Ne-Zheng

    2015-01-01

    This three-part book provides a comprehensive and systematic introduction to the development of useful models for complex systems. Part 1 covers the classical inverse problem for parameter estimation in both deterministic and statistical frameworks, Part 2 is dedicated to system identification, hyperparameter estimation, and model dimension reduction, and Part 3 considers how to collect data and construct reliable models for prediction and decision-making. For the first time, topics such as multiscale inversion, stochastic field parameterization, level set method, machine learning, global sensitivity analysis, data assimilation, model uncertainty quantification, robust design, and goal-oriented modeling, are systematically described and summarized in a single book from the perspective of model inversion, and elucidated with numerical examples from environmental and water resources modeling. Readers of this book will not only learn basic concepts and methods for simple parameter estimation, but also get famili...

  9. Environmental Influences on Independent Collaborative Play

    Science.gov (United States)

    Mawson, Brent

    2010-01-01

    Data from two qualitative research projects indicated a relationship between the type of early childhood setting and children's independent collaborative play. The first research project involved 22 three and four-year-old children in a daylong setting and 47 children four-year-old children in a sessional kindergarten. The second project involved…

  10. Determinatıon of Some Genetic Parameters, Phenotypic, Genetic and Environmental Trends and Environmental Factors Affecting Milk Yield Traits of Brown Swiss Cattle

    Directory of Open Access Journals (Sweden)

    Muhammet Hanifi Selvi

    2016-01-01

    Full Text Available In this study, genetic parameters, macro environmental factors and genetic, phenotypic and environmental trends for actual and 305 day milk yield of Brown Swiss cattle reared in Research Farm of Agricultural College at Atatürk University were estimated. Estimated breeding values that were used for calculation of the genetic trend and genetic parameters were estimated by using MTDFREML computer package program. Environmental factors affecting on actual and 305day milk yields were analysed by using Harvey statistic package program. While effects of the years and parities on the actual and 305-day milk yields were highly significant, the influence of the calving season was found to be insignificant. Environmental and phenotypic trends for actual and 305-day milk yields were determined as -33.2 kg and -29.0 kg; and -27.8±19.1 kg/year and -25.9±8.7 kg/year respectively. Genetic trends for actual and 305-day milk yields were calculated as 5.4±3.8 kg and 3.1±3.4 kg. Heritability’s for actual and 305-day milk yields were 0.21±0.12 and 0.16±0.14 respectively. Repeatability values for actual and 305-day milk yield were found as 0.29 and 0.33 respectively.

  11. Influence of short-term sampling parameters on the uncertainty of the Lden environmental noise indicator

    International Nuclear Information System (INIS)

    Mateus, M; Carrilho, J Dias; Da Silva, M Gameiro

    2015-01-01

    The present study deals with the influence of the sampling parameters on the uncertainty of noise equivalent level in environmental noise measurements. The study has been carried out through the test of different sampling strategies doing resampling trials over continuous monitoring noise files obtained previously in an urban location in the city of Coimbra, in Portugal. On short term measurements, not only the duration of the sampling episodes but also its number have influence on the uncertainty of the result. This influence is higher for the time periods where sound levels suffer a greater variation, such as during the night period. In this period, in case both parameters (duration and number of sampling episodes) are not carefully selected, the uncertainty level can reach too high values contributing to a loss of precision of the measurements. With the obtained data it was investigated the sampling parameters influence on the long term noise indicator uncertainty, calculated according the Draft 1st CD ISO 1996-2:2012 proposed method. It has been verified that this method allows the possibility of defining a general methodology which enables the setting of the parameters once the precision level is fixed. For the three reference periods defined for environmental noise (day, evening and night), it was possible to derive a two variable power law representing the uncertainty of the determined values as a function of the two sampling parameters: duration of sampling episode and number of episodes

  12. ENVIRONMENTAL AND PROCESS PARAMETERS OF METHANE FERMENTATION IN CONTINUOSLY STIRRED TANK REACTOR (CSTR

    Directory of Open Access Journals (Sweden)

    Kamil Kozłowski

    2016-12-01

    Full Text Available A key indicator of methane fermentation process which influences the cost-effectiveness of the biogas plant is efficient production of methane per 1 m3 of reactor. It depends on the proper selection of environmental and process parameters. This article present collected and analyzed the effect of the most important parameters of continuous methane fermentation (CSTR, which include temperature, pH, nutrient content and the C/N ratio in the feed medium, the presence of inhibitors, and the volume load of reactor, retention time and mixing of digestion reactor. Still, the impact of many factors remain unknown, hence there is a need for more comprehensive studies.

  13. A review of Environmental Impact Assessment parameters required for set up of a hydropower project

    International Nuclear Information System (INIS)

    Roy, Pankaj Kumar; Mazumdar, Asis

    2013-01-01

    Environmental Impact Assessment in general, hydro-meteorological conditions, topography, hydrology, water availability analysis of a river system, importance of hydropower and feasibility study of Environmental Impact assessment due to the construction of the hydropower plant have been discussed in this research work. The site selection is one of the major components so far the hydropower is concerned and also the minimum flow should have known to us so that the capacity of a hydropower plant can be predicted. The sustainable flow, which refers the flow is available throughout the year, has been calculated based on flow duration curve. This study highlights the environmental impact assessment particularly related to hydropower project. Here the study area a district town located in the eastern region of India on the banks of river Kosi has been considered. The historical rainfall and the river discharge data have been collected from various organizations. The stage-discharge correlation and hydrological parameters related to hydropower have been analyzed and also to discuss the review of environmental impact assessment in hydropower project. The EIA analysis can be also carried out by using fuzzy logic wherein the EIA parameters can be given different weight-age based on the various survey reports that have been carried out at different places at different time. Such analysis has also been provided below based on the various data obtained.

  14. SYVAC3 parameter distribution package

    Energy Technology Data Exchange (ETDEWEB)

    Andres, T; Skeet, A

    1995-01-01

    SYVAC3 (Systems Variability Analysis Code, generation 3) is a computer program that implements a method called systems variability analysis to analyze the behaviour of a system in the presence of uncertainty. This method is based on simulating the system many times to determine the variation in behaviour it can exhibit. SYVAC3 specializes in systems representing the transport of contaminants, and has several features to simplify the modelling of such systems. It provides a general tool for estimating environmental impacts from the dispersal of contaminants. This report describes a software object type (a generalization of a data type) called Parameter Distribution. This object type is used in SYVAC3, and can also be used independently. Parameter Distribution has the following subtypes: beta distribution; binomial distribution; constant distribution; lognormal distribution; loguniform distribution; normal distribution; piecewise uniform distribution; Triangular distribution; and uniform distribution. Some of these distributions can be altered by correlating two parameter distribution objects. This report provides complete specifications for parameter distributions, and also explains how to use them. It should meet the needs of casual users, reviewers, and programmers who wish to add their own subtypes. (author). 30 refs., 75 tabs., 56 figs.

  15. Aquatic environmental assessment of Lake Balaton in the light of physical-chemical water parameters.

    Science.gov (United States)

    Sebestyén, Vitkor; Németh, József; Juzsakova, Tatjana; Domokos, Endre; Kovács, Zsófia; Rédey, Ákos

    2017-11-01

    One of the issues of the Hungarian Water Management Strategy is the improvement and upgrading of the water of Lake Balaton. The Water Framework Directive (WFD) specifies and sets forth the achievement of the good ecological status. However, the assessment of the water quality of the lake as a complex system requires a comprehensive monitoring and evaluation procedure. Measurements were carried out around the Lake Balaton at ten different locations/sites and 13 physical-chemical parameters were monitored at each measurement site.For the interpretation of the water chemistry parameters the Aquatic Environmental Assessment (AEA) method devised by authors was used for the water body of the Lake Balaton. The AEA method can be used for all types of the water bodies since it is flexible and using individual weighting procedure for the water chemistry parameters comprehensive information can be obtain. The AEA method was compared with existing EIA methods according to a predefined criterion system and proved to be the most suitable tool for evaluating the environmental impacts in our study.On the basis of the results it can be concluded that the status of the quality of studied area on the Lake Balaton can be categorized as proper quality (from the outcome of the ten measurement sites this conclusion was reached at seven sites).

  16. An Investigation of the dependence of CMS RPC operation on environmental parameters

    Energy Technology Data Exchange (ETDEWEB)

    Assran, Y. [Faculty of Petroleum and Mining Eng., Suez Canal University (Egypt); Colafranceschi, S. [INFN Laboratori Nazionali di Frascati, Via E. Fermi 40, I-00044 Frascati (Italy); Doninck, W.A. [Vrije Universiteit Brussel, B-1050 Brussels (Belgium); Sharma, A. [CERN, CH-1211, Geneva (Switzerland); Wickramage, N., E-mail: nwickram@cern.ch [EHEP, Tata Institute of Fundamental Research, Mumbai (India)

    2011-06-15

    In this paper an analysis is presented on performance of RPC chambers installed in the cosmic ray test stand at ISR, CERN. The currents of RPC chambers are studied as a function of environmental parameters such as temperature, humidity and pressure, which are important for the operation of the RPC detector system at CMS. A neural network approach has been used to analyze the data and to build a model using experimental measurements and combining the results of the simulations.

  17. Environmental noise and sleep disturbance: Research in central, eastern and south-eastern Europe and newly independent states

    Directory of Open Access Journals (Sweden)

    Gordana Ristovska

    2013-01-01

    Full Text Available Countries from South-East Europe (SEE, Central and Eastern Europe (CEE and Newly Independent States (NIS are in the process of harmonization with European environmental noise legislation. However, research work on noise and health was performed in some countries independently of harmonization process of adoption and implementation of legislation for environmental noise. Aim of this review is to summarize available evidence for noise induced sleep disturbance in population of CEE, SEE and NIS countries and to give directions for further research work in this field. After a systematic search through accessible electronic databases, conference proceedings, PhD thesis, national reports and scientific journals in English and non-English language, we decided to include six papers and one PhD thesis in this review: One paper from former Yugoslavia, one paper from Slovakia, one paper from Lithuania, two papers from Serbia and one paper, as also one PhD thesis from The Former Yugoslav Republic of Macedonia. Noise exposure assessment focused on road traffic noise was mainly performed with objective noise measurements, but also with noise mapping in case of Lithuanian study. Sleep disturbance was assessed with the questionnaire based surveys and was assumed from dose-effect relationship between night-time noise indicator (Lnight for road traffic noise and sleep disturbance (for Lithuanian study. Although research evidence on noise and sleep disturbance show to be sufficient for establishing dose response curves for sleep disturbance in countries where studies were performed, further research is needed with particular attention to vulnerable groups, other noise sources, development of laboratory research work and common methodology in assessment of burden of diseases from environmental noise.

  18. Environmental noise and sleep disturbance: research in Central, Eastern and South-Eastern Europe and Newly Independent States.

    Science.gov (United States)

    Ristovska, Gordana; Lekaviciute, Jurgita

    2013-01-01

    Countries from South-East Europe (SEE), Central and Eastern Europe (CEE) and Newly Independent States (NIS) are in the process of harmonization with European environmental noise legislation. However, research work on noise and health was performed in some countries independently of harmonization process of adoption and implementation of legislation for environmental noise. Aim of this review is to summarize available evidence for noise induced sleep disturbance in population of CEE, SEE and NIS countries and to give directions for further research work in this field. After a systematic search through accessible electronic databases, conference proceedings, PhD thesis, national reports and scientific journals in English and non-English language, we decided to include six papers and one PhD thesis in this review: One paper from former Yugoslavia, one paper from Slovakia, one paper from Lithuania, two papers from Serbia and one paper, as also one PhD thesis from The Former Yugoslav Republic of Macedonia. Noise exposure assessment focused on road traffic noise was mainly performed with objective noise measurements, but also with noise mapping in case of Lithuanian study. Sleep disturbance was assessed with the questionnaire based surveys and was assumed from dose-effect relationship between night-time noise indicator (Lnight ) for road traffic noise and sleep disturbance (for Lithuanian study). Although research evidence on noise and sleep disturbance show to be sufficient for establishing dose response curves for sleep disturbance in countries where studies were performed, further research is needed with particular attention to vulnerable groups, other noise sources, development of laboratory research work and common methodology in assessment of burden of diseases from environmental noise.

  19. Independent procedure of checking dose calculations using an independent calculus algorithm

    International Nuclear Information System (INIS)

    Perez Rozos, A.; Jerez Sainz, I.; Carrasco Rodriguez, J. L.

    2006-01-01

    In radiotherapy it is recommended the use of an independent procedure of checking dose calculations, in order to verify the main treatment planning system and double check every patient dosimetry. In this work we present and automatic spreadsheet that import data from planning system using IMPAC/RTP format and verify monitor unit calculation using an independent calculus algorithm. Additionally, it perform a personalized analysis of dose volume histograms and several radiobiological parameters like TCP and NTCP. Finally, the application automatically generate a clinical dosimetry report for every patient, including treatment fields, fractionation, independent check results, dose volume analysis, and first day forms. (Author)

  20. Model-independent measurement of mixing parameters in $D^0 \\to K_S^0 \\pi^+ \\pi^-$ decays

    CERN Document Server

    Aaij, Roel; Adeva, Bernardo; Adinolfi, Marco; Affolder, Anthony; Ajaltouni, Ziad; Akar, Simon; Albrecht, Johannes; Alessio, Federico; Alexander, Michael; Ali, Suvayu; Alkhazov, Georgy; Alvarez Cartelle, Paula; Alves Jr, Antonio Augusto; Amato, Sandra; Amerio, Silvia; Amhis, Yasmine; An, Liupan; Anderlini, Lucio; Anderson, Jonathan; Andreassi, Guido; Andreotti, Mirco; Andrews, Jason; Appleby, Robert; Aquines Gutierrez, Osvaldo; Archilli, Flavio; d'Argent, Philippe; Artamonov, Alexander; Artuso, Marina; Aslanides, Elie; Auriemma, Giulio; Baalouch, Marouen; Bachmann, Sebastian; Back, John; Badalov, Alexey; Baesso, Clarissa; Baldini, Wander; Barlow, Roger; Barschel, Colin; Barsuk, Sergey; Barter, William; Batozskaya, Varvara; Battista, Vincenzo; Bay, Aurelio; Beaucourt, Leo; Beddow, John; Bedeschi, Franco; Bediaga, Ignacio; Bel, Lennaert; Bellee, Violaine; Belloli, Nicoletta; Belyaev, Ivan; Ben-Haim, Eli; Bencivenni, Giovanni; Benson, Sean; Benton, Jack; Berezhnoy, Alexander; Bernet, Roland; Bertolin, Alessandro; Bettler, Marc-Olivier; van Beuzekom, Martinus; Bien, Alexander; Bifani, Simone; Billoir, Pierre; Bird, Thomas; Birnkraut, Alex; Bizzeti, Andrea; Blake, Thomas; Blanc, Frédéric; Blouw, Johan; Blusk, Steven; Bocci, Valerio; Bondar, Alexander; Bondar, Nikolay; Bonivento, Walter; Borghi, Silvia; Borsato, Martino; Bowcock, Themistocles; Bowen, Espen Eie; Bozzi, Concezio; Braun, Svende; Britsch, Markward; Britton, Thomas; Brodzicka, Jolanta; Brook, Nicholas; Buchanan, Emma; Burr, Christopher; Bursche, Albert; Buytaert, Jan; Cadeddu, Sandro; Calabrese, Roberto; Calvi, Marta; Calvo Gomez, Miriam; Campana, Pierluigi; Campora Perez, Daniel; Capriotti, Lorenzo; Carbone, Angelo; Carboni, Giovanni; Cardinale, Roberta; Cardini, Alessandro; Carniti, Paolo; Carson, Laurence; Carvalho Akiba, Kazuyoshi; Casse, Gianluigi; Cassina, Lorenzo; Castillo Garcia, Lucia; Cattaneo, Marco; Cauet, Christophe; Cavallero, Giovanni; Cenci, Riccardo; Charles, Matthew; Charpentier, Philippe; Chefdeville, Maximilien; Chen, Shanzhen; Cheung, Shu-Faye; Chiapolini, Nicola; Chrzaszcz, Marcin; Cid Vidal, Xabier; Ciezarek, Gregory; Clarke, Peter; Clemencic, Marco; Cliff, Harry; Closier, Joel; Coco, Victor; Cogan, Julien; Cogneras, Eric; Cogoni, Violetta; Cojocariu, Lucian; Collazuol, Gianmaria; Collins, Paula; Comerma-Montells, Albert; Contu, Andrea; Cook, Andrew; Coombes, Matthew; Coquereau, Samuel; Corti, Gloria; Corvo, Marco; Couturier, Benjamin; Cowan, Greig; Craik, Daniel Charles; Crocombe, Andrew; Cruz Torres, Melissa Maria; Cunliffe, Samuel; Currie, Robert; D'Ambrosio, Carmelo; Dall'Occo, Elena; Dalseno, Jeremy; David, Pieter; Davis, Adam; De Aguiar Francisco, Oscar; De Bruyn, Kristof; De Capua, Stefano; De Cian, Michel; De Miranda, Jussara; De Paula, Leandro; De Simone, Patrizia; Dean, Cameron Thomas; Decamp, Daniel; Deckenhoff, Mirko; Del Buono, Luigi; Déléage, Nicolas; Demmer, Moritz; Derkach, Denis; Deschamps, Olivier; Dettori, Francesco; Dey, Biplab; Di Canto, Angelo; Di Ruscio, Francesco; Dijkstra, Hans; Donleavy, Stephanie; Dordei, Francesca; Dorigo, Mirco; Dosil Suárez, Alvaro; Dossett, David; Dovbnya, Anatoliy; Dreimanis, Karlis; Dufour, Laurent; Dujany, Giulio; Dupertuis, Frederic; Durante, Paolo; Dzhelyadin, Rustem; Dziurda, Agnieszka; Dzyuba, Alexey; Easo, Sajan; Egede, Ulrik; Egorychev, Victor; Eidelman, Semen; Eisenhardt, Stephan; Eitschberger, Ulrich; Ekelhof, Robert; Eklund, Lars; El Rifai, Ibrahim; Elsasser, Christian; Ely, Scott; Esen, Sevda; Evans, Hannah Mary; Evans, Timothy; Falabella, Antonio; Färber, Christian; Farley, Nathanael; Farry, Stephen; Fay, Robert; Ferguson, Dianne; Fernandez Albor, Victor; Ferrari, Fabio; Ferreira Rodrigues, Fernando; Ferro-Luzzi, Massimiliano; Filippov, Sergey; Fiore, Marco; Fiorini, Massimiliano; Firlej, Miroslaw; Fitzpatrick, Conor; Fiutowski, Tomasz; Fohl, Klaus; Fol, Philip; Fontana, Marianna; Fontanelli, Flavio; Forshaw, Dean Charles; Forty, Roger; Frank, Markus; Frei, Christoph; Frosini, Maddalena; Fu, Jinlin; Furfaro, Emiliano; Gallas Torreira, Abraham; Galli, Domenico; Gallorini, Stefano; Gambetta, Silvia; Gandelman, Miriam; Gandini, Paolo; Gao, Yuanning; García Pardiñas, Julián; Garra Tico, Jordi; Garrido, Lluis; Gascon, David; Gaspar, Clara; Gauld, Rhorry; Gavardi, Laura; Gazzoni, Giulio; Gerick, David; Gersabeck, Evelina; Gersabeck, Marco; Gershon, Timothy; Ghez, Philippe; Gianì, Sebastiana; Gibson, Valerie; Girard, Olivier Göran; Giubega, Lavinia-Helena; Gligorov, V.V.; Göbel, Carla; Golubkov, Dmitry; Golutvin, Andrey; Gomes, Alvaro; Gotti, Claudio; Grabalosa Gándara, Marc; Graciani Diaz, Ricardo; Granado Cardoso, Luis Alberto; Graugés, Eugeni; Graverini, Elena; Graziani, Giacomo; Grecu, Alexandru; Greening, Edward; Gregson, Sam; Griffith, Peter; Grillo, Lucia; Grünberg, Oliver; Gui, Bin; Gushchin, Evgeny; Guz, Yury; Gys, Thierry; Hadavizadeh, Thomas; Hadjivasiliou, Christos; Haefeli, Guido; Haen, Christophe; Haines, Susan; Hall, Samuel; Hamilton, Brian; Han, Xiaoxue; Hansmann-Menzemer, Stephanie; Harnew, Neville; Harnew, Samuel; Harrison, Jonathan; He, Jibo; Head, Timothy; Heijne, Veerle; Hennessy, Karol; Henrard, Pierre; Henry, Louis; van Herwijnen, Eric; Heß, Miriam; Hicheur, Adlène; Hill, Donal; Hoballah, Mostafa; Hombach, Christoph; Hulsbergen, Wouter; Humair, Thibaud; Hussain, Nazim; Hutchcroft, David; Hynds, Daniel; Idzik, Marek; Ilten, Philip; Jacobsson, Richard; Jaeger, Andreas; Jalocha, Pawel; Jans, Eddy; Jawahery, Abolhassan; Jing, Fanfan; John, Malcolm; Johnson, Daniel; Jones, Christopher; Joram, Christian; Jost, Beat; Jurik, Nathan; Kandybei, Sergii; Kanso, Walaa; Karacson, Matthias; Karbach, Moritz; Karodia, Sarah; Kecke, Matthieu; Kelsey, Matthew; Kenyon, Ian; Kenzie, Matthew; Ketel, Tjeerd; Khairullin, Egor; Khanji, Basem; Khurewathanakul, Chitsanu; Klaver, Suzanne; Klimaszewski, Konrad; Kochebina, Olga; Kolpin, Michael; Komarov, Ilya; Koopman, Rose; Koppenburg, Patrick; Kozeiha, Mohamad; Kravchuk, Leonid; Kreplin, Katharina; Kreps, Michal; Krocker, Georg; Krokovny, Pavel; Kruse, Florian; Krzemien, Wojciech; Kucewicz, Wojciech; Kucharczyk, Marcin; Kudryavtsev, Vasily; Kuonen, Axel Kevin; Kurek, Krzysztof; Kvaratskheliya, Tengiz; Lacarrere, Daniel; Lafferty, George; Lai, Adriano; Lambert, Dean; Lanfranchi, Gaia; Langenbruch, Christoph; Langhans, Benedikt; Latham, Thomas; Lazzeroni, Cristina; Le Gac, Renaud; van Leerdam, Jeroen; Lees, Jean-Pierre; Lefèvre, Regis; Leflat, Alexander; Lefrançois, Jacques; Lemos Cid, Edgar; Leroy, Olivier; Lesiak, Tadeusz; Leverington, Blake; Li, Yiming; Likhomanenko, Tatiana; Liles, Myfanwy; Lindner, Rolf; Linn, Christian; Lionetto, Federica; Liu, Bo; Liu, Xuesong; Loh, David; Longstaff, Iain; Lopes, Jose; Lucchesi, Donatella; Lucio Martinez, Miriam; Luo, Haofei; Lupato, Anna; Luppi, Eleonora; Lupton, Oliver; Lusiani, Alberto; Machefert, Frederic; Maciuc, Florin; Maev, Oleg; Maguire, Kevin; Malde, Sneha; Malinin, Alexander; Manca, Giulia; Mancinelli, Giampiero; Manning, Peter Michael; Mapelli, Alessandro; Maratas, Jan; Marchand, Jean François; Marconi, Umberto; Marin Benito, Carla; Marino, Pietro; Marks, Jörg; Martellotti, Giuseppe; Martin, Morgan; Martinelli, Maurizio; Martinez Santos, Diego; Martinez Vidal, Fernando; Martins Tostes, Danielle; Massafferri, André; Matev, Rosen; Mathad, Abhijit; Mathe, Zoltan; Matteuzzi, Clara; Mauri, Andrea; Maurin, Brice; Mazurov, Alexander; McCann, Michael; McCarthy, James; McNab, Andrew; McNulty, Ronan; Meadows, Brian; Meier, Frank; Meissner, Marco; Melnychuk, Dmytro; Merk, Marcel; Michielin, Emanuele; Milanes, Diego Alejandro; Minard, Marie-Noelle; Mitzel, Dominik Stefan; Molina Rodriguez, Josue; Monroy, Ignacio Alberto; Monteil, Stephane; Morandin, Mauro; Morawski, Piotr; Mordà, Alessandro; Morello, Michael Joseph; Moron, Jakub; Morris, Adam Benjamin; Mountain, Raymond; Muheim, Franz; Müller, Dominik; Müller, Janine; Müller, Katharina; Müller, Vanessa; Mussini, Manuel; Muster, Bastien; Naik, Paras; Nakada, Tatsuya; Nandakumar, Raja; Nandi, Anita; Nasteva, Irina; Needham, Matthew; Neri, Nicola; Neubert, Sebastian; Neufeld, Niko; Neuner, Max; Nguyen, Anh Duc; Nguyen, Thi-Dung; Nguyen-Mau, Chung; Niess, Valentin; Niet, Ramon; Nikitin, Nikolay; Nikodem, Thomas; Novoselov, Alexey; O'Hanlon, Daniel Patrick; Oblakowska-Mucha, Agnieszka; Obraztsov, Vladimir; Ogilvy, Stephen; Okhrimenko, Oleksandr; Oldeman, Rudolf; Onderwater, Gerco; Osorio Rodrigues, Bruno; Otalora Goicochea, Juan Martin; Otto, Adam; Owen, Patrick; Oyanguren, Maria Aranzazu; Palano, Antimo; Palombo, Fernando; Palutan, Matteo; Panman, Jacob; Papanestis, Antonios; Pappagallo, Marco; Pappalardo, Luciano; Pappenheimer, Cheryl; Parker, William; Parkes, Christopher; Passaleva, Giovanni; Patel, Girish; Patel, Mitesh; Patrignani, Claudia; Pearce, Alex; Pellegrino, Antonio; Penso, Gianni; Pepe Altarelli, Monica; Perazzini, Stefano; Perret, Pascal; Pescatore, Luca; Petridis, Konstantinos; Petrolini, Alessandro; Petruzzo, Marco; Picatoste Olloqui, Eduardo; Pietrzyk, Boleslaw; Pilař, Tomas; Pinci, Davide; Pistone, Alessandro; Piucci, Alessio; Playfer, Stephen; Plo Casasus, Maximo; Poikela, Tuomas; Polci, Francesco; Poluektov, Anton; Polyakov, Ivan; Polycarpo, Erica; Popov, Alexander; Popov, Dmitry; Popovici, Bogdan; Potterat, Cédric; Price, Eugenia; Price, Joseph David; Prisciandaro, Jessica; Pritchard, Adrian; Prouve, Claire; Pugatch, Valery; Puig Navarro, Albert; Punzi, Giovanni; Qian, Wenbin; Quagliani, Renato; Rachwal, Bartolomiej; Rademacker, Jonas; Rama, Matteo; Rangel, Murilo; Raniuk, Iurii; Rauschmayr, Nathalie; Raven, Gerhard; Redi, Federico; Reichert, Stefanie; Reid, Matthew; dos Reis, Alberto; Ricciardi, Stefania; Richards, Sophie; Rihl, Mariana; Rinnert, Kurt; Rives Molina, Vincente; Robbe, Patrick; Rodrigues, Ana Barbara; Rodrigues, Eduardo; Rodriguez Lopez, Jairo Alexis; Rodriguez Perez, Pablo; Roiser, Stefan; Romanovsky, Vladimir; Romero Vidal, Antonio; Ronayne, John William; Rotondo, Marcello; Rouvinet, Julien; Ruf, Thomas; Ruiz Valls, Pablo; Saborido Silva, Juan Jose; Sagidova, Naylya; Sail, Paul; Saitta, Biagio; Salustino Guimaraes, Valdir; Sanchez Mayordomo, Carlos; Sanmartin Sedes, Brais; Santacesaria, Roberta; Santamarina Rios, Cibran; Santimaria, Marco; Santovetti, Emanuele; Sarti, Alessio; Satriano, Celestina; Satta, Alessia; Saunders, Daniel Martin; Savrina, Darya; Schiller, Manuel; Schindler, Heinrich; Schlupp, Maximilian; Schmelling, Michael; Schmelzer, Timon; Schmidt, Burkhard; Schneider, Olivier; Schopper, Andreas; Schubiger, Maxime; Schune, Marie Helene; Schwemmer, Rainer; Sciascia, Barbara; Sciubba, Adalberto; Semennikov, Alexander; Serra, Nicola; Serrano, Justine; Sestini, Lorenzo; Seyfert, Paul; Shapkin, Mikhail; Shapoval, Illya; Shcheglov, Yury; Shears, Tara; Shekhtman, Lev; Shevchenko, Vladimir; Shires, Alexander; Siddi, Benedetto Gianluca; Silva Coutinho, Rafael; Silva de Oliveira, Luiz Gustavo; Simi, Gabriele; Sirendi, Marek; Skidmore, Nicola; Skwarnicki, Tomasz; Smith, Edmund; Smith, Eluned; Smith, Iwan Thomas; Smith, Jackson; Smith, Mark; Snoek, Hella; Sokoloff, Michael; Soler, Paul; Soomro, Fatima; Souza, Daniel; Souza De Paula, Bruno; Spaan, Bernhard; Spradlin, Patrick; Sridharan, Srikanth; Stagni, Federico; Stahl, Marian; Stahl, Sascha; Stefkova, Slavorima; Steinkamp, Olaf; Stenyakin, Oleg; Stevenson, Scott; Stoica, Sabin; Stone, Sheldon; Storaci, Barbara; Stracka, Simone; Straticiuc, Mihai; Straumann, Ulrich; Sun, Liang; Sutcliffe, William; Swientek, Krzysztof; Swientek, Stefan; Syropoulos, Vasileios; Szczekowski, Marek; Szumlak, Tomasz; T'Jampens, Stephane; Tayduganov, Andrey; Tekampe, Tobias; Teklishyn, Maksym; Tellarini, Giulia; Teubert, Frederic; Thomas, Christopher; Thomas, Eric; van Tilburg, Jeroen; Tisserand, Vincent; Tobin, Mark; Todd, Jacob; Tolk, Siim; Tomassetti, Luca; Tonelli, Diego; Topp-Joergensen, Stig; Torr, Nicholas; Tournefier, Edwige; Tourneur, Stephane; Trabelsi, Karim; Tran, Minh Tâm; Tresch, Marco; Trisovic, Ana; Tsaregorodtsev, Andrei; Tsopelas, Panagiotis; Tuning, Niels; Ukleja, Artur; Ustyuzhanin, Andrey; Uwer, Ulrich; Vacca, Claudia; Vagnoni, Vincenzo; Valenti, Giovanni; Vallier, Alexis; Vazquez Gomez, Ricardo; Vazquez Regueiro, Pablo; Vázquez Sierra, Carlos; Vecchi, Stefania; Velthuis, Jaap; Veltri, Michele; Veneziano, Giovanni; Vesterinen, Mika; Viaud, Benoit; Vieira, Daniel; Vieites Diaz, Maria; Vilasis-Cardona, Xavier; Volkov, Vladimir; Vollhardt, Achim; Volyanskyy, Dmytro; Voong, David; Vorobyev, Alexey; Vorobyev, Vitaly; Voß, Christian; de Vries, Jacco; Waldi, Roland; Wallace, Charlotte; Wallace, Ronan; Walsh, John; Wandernoth, Sebastian; Wang, Jianchun; Ward, David; Watson, Nigel; Websdale, David; Weiden, Andreas; Whitehead, Mark; Wilkinson, Guy; Wilkinson, Michael; Williams, Mark Richard James; Williams, Matthew; Williams, Mike; Williams, Timothy; Wilson, Fergus; Wimberley, Jack; Wishahi, Julian; Wislicki, Wojciech; Witek, Mariusz; Wormser, Guy; Wotton, Stephen; Wyllie, Kenneth; Xie, Yuehong; Xu, Zhirui; Yang, Zhenwei; Yu, Jiesheng; Yuan, Xuhao; Yushchenko, Oleg; Zangoli, Maria; Zavertyaev, Mikhail; Zhang, Liming; Zhang, Yanxi; Zhelezov, Alexey; Zhokhov, Anatoly; Zhong, Liang; Zucchelli, Stefano

    2016-04-06

    The first model-independent measurement of the charm mixing parameters in the decay $D^0 \\to K_S \\pi^+ \\pi^-$ is reported, using a sample of $pp$ collision data recorded by the LHCb experiment, corresponding to an integrated luminosity of 1.0 fb$^{-1}$ at a centre-of-mass energy of 7 TeV. The measured values are \\begin{eqnarray*} x &=& ( -0.86 \\pm 0.53 \\pm 0.17 ) \\times 10^{-2}, \\\\ y &=& ( +0.03 \\pm 0.46 \\pm 0.13 ) \\times 10^{-2}, \\end{eqnarray*} where the first uncertainties are statistical and include small contributions due to the external input for the strong phase measured by the CLEO collaboration, and the second uncertainties are systematic.

  1. Sensitivity of tidal sand wave characteristics to environmental parameters: A combined data analysis and modelling approach

    NARCIS (Netherlands)

    van Santen, R.B.; de Swart, H.E.; van Dijk, T.A.G.P.

    2011-01-01

    An integrated field data-modelling approach is employed to investigate relationships between the wavelength of tidal sand waves and four environmental parameters: tidal current amplitude, water depth, tidal ellipticity and median grain size. From echo sounder data at 23 locations on the Dutch

  2. Predicting the activity coefficients of free-solvent for concentrated globular protein solutions using independently determined physical parameters.

    Directory of Open Access Journals (Sweden)

    Devin W McBride

    Full Text Available The activity coefficient is largely considered an empirical parameter that was traditionally introduced to correct the non-ideality observed in thermodynamic systems such as osmotic pressure. Here, the activity coefficient of free-solvent is related to physically realistic parameters and a mathematical expression is developed to directly predict the activity coefficients of free-solvent, for aqueous protein solutions up to near-saturation concentrations. The model is based on the free-solvent model, which has previously been shown to provide excellent prediction of the osmotic pressure of concentrated and crowded globular proteins in aqueous solutions up to near-saturation concentrations. Thus, this model uses only the independently determined, physically realizable quantities: mole fraction, solvent accessible surface area, and ion binding, in its prediction. Predictions are presented for the activity coefficients of free-solvent for near-saturated protein solutions containing either bovine serum albumin or hemoglobin. As a verification step, the predictability of the model for the activity coefficient of sucrose solutions was evaluated. The predicted activity coefficients of free-solvent are compared to the calculated activity coefficients of free-solvent based on osmotic pressure data. It is observed that the predicted activity coefficients are increasingly dependent on the solute-solvent parameters as the protein concentration increases to near-saturation concentrations.

  3. Indoor air quality in the Karns research houses: baseline measurements and impact of indoor environmental parameters on formaldehyde concentrations

    International Nuclear Information System (INIS)

    Matthews, T.G.; Fung, K.W.; Tromberg, B.J.; Hawthorne, A.R.

    1985-12-01

    Baseline indoor air quality measurements, a nine-month radon study, and an environmental parameters study examining the impact of indoor temperature (T) and relative humidity (RH) levels on formaldehyde (CH 2 O) concentrations have been performed in three unoccupied research homes located in Karns, Tennessee. Inter-house comparison measurements of (1) CH 2 O concentration, (2) CH 2 O emission rates from primary CH 2 O emission sources, (3) radon and radon daughter concentrations, and (4) air exchange rates indicate that the three homes are similar. The results of the nine-month radon study indicate indoor concentrations consistently below the EPA recommended level of 4 pCi/L. Evidence was found that crawl-space concentrations may be reduced using heat pump systems whose outdoor units circulate fresh air through the crawl-space. The modeled results of the environmental parameters study indicate approximate fourfold increases in CH 2 O concentrations from 0.07 to 0.27 ppM for seasonal T and RH conditions of 20 0 C, 30% RH and 29 0 C, 80% RH, respectively. Evaluation of these environmental parameters study data with steady-state CH 2 O concentration models developed from laboratory studies of the environmental dependence of CH 2 O emissions from particleboard underlayment indicate good correlations between the laboratory and field studies

  4. Parameters affecting the environmental impact of a range of dairy farming systems in Denmark, Germany and Italy

    DEFF Research Database (Denmark)

    Guerci, Matteo; Knudsen, Marie Trydeman; Bava, L.

    2013-01-01

    The environmental impact of 12 dairy farms in Denmark, Germany and Italy was evaluated using an LCA approach and the most important parameters influencing their environmental sustainability were identified. The farms represent different production methods (organic vs. conventional), summer feeding...... intensive Italian farming system with very similar environmental impact values. However, a sensitivity analysis showed that when emissions relating to direct land use change of soybean production were included in the assessment, the GWP changed considerably for the conventional farms due to the inclusion...... of conventional soymeal in the feed concentrate. There were strong and positive correlations between the four impact categories, and overall the results indicate that improving greenhouse gas emissions would improve the general environmental sustainability of the dairy farm. The land occupation was lowest...

  5. Environmental implications of electricity purchase from independent power producers: a case study from Thailand

    International Nuclear Information System (INIS)

    Rabin Shrestha; Ram M Shrestha

    2003-01-01

    This paper analyses the effect on the environment of electricity purchase from independent power producers (IPPs) in the case of Thailand. The environmental implication is evaluated in terms of the net change in emission of air pollutants with electricity purchase from IPPs by a utility. The main finding of the study is that electricity purchase from a non-dispatchable IPP plant based on coal-fired generation would increase the net emissions compared with that without the purchase from IPPs. The study also shows that the lower plant factor of the IPP plant would also increase the emission of air pollutants. Furthermore, with non-dispatchable IPP plants, the total emission of air pollutants would increase, whereas with dispatchable IPP plants the total emission would decrease with the level of electricity purchases. (author)

  6. Annual Radiological Environmental Monitoring Program Report for the Three Mile Island, Unit 2, Independent Spent Fuel Storage Installation

    International Nuclear Information System (INIS)

    Hall, Gregory Graham

    2002-01-01

    This report presents the results of the 2001 Radiological Environmental Monitoring Program conducted in accordance with 10 CFR 72.44 for the Three Mile Island, Unit 2, Independent Spent Fuel Storage Installation. A description of the facility and the monitoring program is provided. The results of monitoring the two predominant radiation exposure pathways, potential airborne radioactivity releases and direct radiation exposure, indicate the facility operation has not contributed to any increase in the estimated maximum potential dose commitment to the general public.

  7. Evaluation of Parameter Uncertainty Reduction in Groundwater Flow Modeling Using Multiple Environmental Tracers

    Science.gov (United States)

    Arnold, B. W.; Gardner, P.

    2013-12-01

    Calibration of groundwater flow models for the purpose of evaluating flow and aquifer heterogeneity typically uses observations of hydraulic head in wells and appropriate boundary conditions. Environmental tracers have a wide variety of decay rates and input signals in recharge, resulting in a potentially broad source of additional information to constrain flow rates and heterogeneity. A numerical study was conducted to evaluate the reduction in uncertainty during model calibration using observations of various environmental tracers and combinations of tracers. A synthetic data set was constructed by simulating steady groundwater flow and transient tracer transport in a high-resolution, 2-D aquifer with heterogeneous permeability and porosity using the PFLOTRAN software code. Data on pressure and tracer concentration were extracted at well locations and then used as observations for automated calibration of a flow and transport model using the pilot point method and the PEST code. Optimization runs were performed to estimate parameter values of permeability at 30 pilot points in the model domain for cases using 42 observations of: 1) pressure, 2) pressure and CFC11 concentrations, 3) pressure and Ar-39 concentrations, and 4) pressure, CFC11, Ar-39, tritium, and He-3 concentrations. Results show significantly lower uncertainty, as indicated by the 95% linear confidence intervals, in permeability values at the pilot points for cases including observations of environmental tracer concentrations. The average linear uncertainty range for permeability at the pilot points using pressure observations alone is 4.6 orders of magnitude, using pressure and CFC11 concentrations is 1.6 orders of magnitude, using pressure and Ar-39 concentrations is 0.9 order of magnitude, and using pressure, CFC11, Ar-39, tritium, and He-3 concentrations is 1.0 order of magnitude. Data on Ar-39 concentrations result in the greatest parameter uncertainty reduction because its half-life of 269

  8. Parameters used in the environmental pathways and radiological dose modules (DESCARTES, CIDER, and CRD codes) of the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC)

    International Nuclear Information System (INIS)

    Snyder, S.F.; Farris, W.T.; Napier, B.A.; Ikenberry, T.A.; Gilbert, R.O.

    1994-05-01

    This letter report is a description of work performed for the Hanford Environmental Dose Reconstruction (HEDR) Project. The HEDR Project was established to estimate the radiation doses to individuals resulting from releases of radionuclides from the Hanford Site during the period of 1944 to 1992. This work is being done by staff at Battelle, Pacific Northwest Laboratories under a contract with the Centers for Disease Control and Prevention with technical direction provided by an independent Technical Steering Panel (TSP)

  9. Parameters used in the environmental pathways and radiological dose modules (DESCARTES, CIDER, and CRD codes) of the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC)

    Energy Technology Data Exchange (ETDEWEB)

    Snyder, S.F.; Farris, W.T.; Napier, B.A.; Ikenberry, T.A.; Gilbert, R.O.

    1994-05-01

    This letter report is a description of work performed for the Hanford Environmental Dose Reconstruction (HEDR) Project. The HEDR Project was established to estimate the radiation doses to individuals resulting from releases of radionuclides from the Hanford Site during the period of 1944 to 1992. This work is being done by staff at Battelle, Pacific Northwest Laboratories under a contract with the Centers for Disease Control and Prevention with technical direction provided by an independent Technical Steering Panel (TSP).

  10. Seasonal variation of semen parameters correlates with environmental temperature and air pollution: A big data analysis over 6 years.

    Science.gov (United States)

    Santi, Daniele; Magnani, Elisa; Michelangeli, Marco; Grassi, Roberto; Vecchi, Barbara; Pedroni, Gioia; Roli, Laura; De Santis, Maria Cristina; Baraldi, Enrica; Setti, Monica; Trenti, Tommaso; Simoni, Manuela

    2018-04-01

    Male fertility is progressively declining in many developed countries, but the relationship between male infertility and environmental factors is still unclear. To assess the influence of environmental temperature and air pollution on semen parameters, using a big-data approach. A big data analysis of parameters related to 5131 men, living in a province of Northern Italy and undergoing semen analyses between January 2010 and March 2016 was performed. Ambient temperature was recorded on the day of analysis and the 90 days prior to the analysis and the average value of particulate matter (PM) and NO2 in the year of the test. All data were acquired by geocoding patients residential address. A data warehouse containing 990,904,591 data was generated and analysed by multiple regressions. 5573 semen analyses were collected. Both maximum and minimum temperatures registered on the day of collection were inversely related to total sperm number (p < .001), non-progressive motility (NPrM) (p < .005) and normal forms (p < .001). Results were confirmed considering temperature in the 30 and 60 days before collection, but not in the 90 days before collection. Total sperm number was lower in summer/autumn (p < .001) and was inversely related with daylight duration (p < .001). PM10 and PM2.5 were inversely related to PrM (p < .001 and p < .005) and abnormal forms (p < .001). This is the first evaluation of the relationship between male fertility-related parameters and environment using a big-data approach. A seasonal change in semen parameters was found, with a fluctuation related to both temperature and daylight duration. A negative correlation between air pollution and semen quality is suggested. Such seasonal and environmental associations should be considered when assessing changes of male fertility-related parameters over time. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. The impact of highway base-saturation flow rate adjustment on Kuwait's transport and environmental parameters estimation.

    Science.gov (United States)

    AlRukaibi, Fahad; AlKheder, Sharaf; Al-Rukaibi, Duaij; Al-Burait, Abdul-Aziz

    2018-03-23

    Traditional transportation systems' management and operation mainly focused on improving traffic mobility and safety without imposing any environmental concerns. Transportation and environmental issues are interrelated and affected by the same parameters especially at signalized intersections. Additionally, traffic congestion at signalized intersections has a major contribution in the environmental problem as related to vehicle emission, fuel consumption, and delay. Therefore, signalized intersections' design and operation is an important parameter to minimize the impact on the environment. The design and operation of signalized intersections are highly dependent on the base saturation flow rate (BSFR). Highway Capacity Manual (HCM) uses a base-saturation flow rate of 1900-passenger car/h/lane for areas with a population intensity greater than or equal to 250,000 and a value of 1750-passenger car/h/lane for less populated areas. The base-saturation flow rate value in HCM is derived from a field data collected in developed countries. The adopted value in Kuwait is 1800passengercar/h/lane, which is the value that used in this analysis as a basis for comparison. Due to the difference in behavior between drivers in developed countries and their fellows in Kuwait, an adjustment was made to the base-saturation flow rate to represent Kuwait's traffic and environmental conditions. The reduction in fuel consumption and vehicles' emission after modifying the base-saturation flow rate (BSFR increased by 12.45%) was about 34% on average. Direct field measurements of the saturation flow rate were used while using the air quality mobile lab to calculate emissions' rates. Copyright © 2018 Elsevier B.V. All rights reserved.

  12. Electron efficiency of nZVI does not change with variation of environmental parameters

    Energy Technology Data Exchange (ETDEWEB)

    Schöftner, Philipp, E-mail: philipp.schoeftner@ait.ac.at [AIT Austrian Institute of Technology GmbH, Konrad-Lorenz-Straße 24, 3430 Tulln a.d. Donau (Austria); Waldner, Georg [AIT Austrian Institute of Technology GmbH, Konrad-Lorenz-Straße 24, 3430 Tulln a.d. Donau (Austria); Lottermoser, Werner, E-mail: werner.lottermoser@sbg.ac.at [Salzburg University, FB Materialforschung und Physik, Hellbrunnerstr. 34, 5020 Salzburg (Austria); Stöger-Pollach, Michael, E-mail: stoeger@ustem.tuwien.ac.at [Technical University of Vienna, Universitäre Service-Einrichtung für Transmissionselektronenmikroskopie — USTEM (Austria); Freitag, Peter, E-mail: p.freitag@kellergrundbau.at [Keller Grundbau Ges. mbH, Mariahilfer Straße 127a, 1150 Vienna (Austria); Reichenauer, Thomas G., E-mail: thomas.reichenauer@ait.ac.at [AIT Austrian Institute of Technology GmbH, Konrad-Lorenz-Straße 24, 3430 Tulln a.d. Donau (Austria)

    2015-12-01

    Nanoscale zero-valent iron particles (nZVI) are already applied for in-situ dechlorination of halogenated organic contaminants in the field. We performed batch experiments whereby trichloroethene (TCE) was dehalogenated by nZVI under different environmental conditions that are relevant in practice. The tested conditions include different ionic strengths, addition of polyelectrolytes (carboxymethylcellulose and ligninsulphonate), lowered temperature, dissolved oxygen and different particle contents. Particle properties were determined by Mössbauer spectroscopy, XRD, TEM, SEM, AAS and laser obscuration time measurements. TCE dehalogenation and H{sub 2} evolution were decelerated by reduced ionic strength, addition of polyelectrolytes, temperature reduction, the presence of dissolved oxygen and reduced particle content. The partitioning of released electrons between reactions with the contaminant vs. with water (selectivity) was low, independent of the tested conditions. Basically out of hundred electrons that were released via nZVI oxidation only 3.1 ± 1.4 were used for TCE dehalogenation. Even lower selectivities were observed at TCE concentrations below 3.5 mg l{sup −1}, hence particle modifications and/or combination of nZVI with other remediation technologies seem to be necessary to reach target concentrations for remediation. Our results suggest that selectivity is particle intrinsic and not as much condition dependent, hence particle synthesis and potential particle modifications of nZVI particles may be more important for optimization of the pollutant degradation rate, than tested environmental conditions. - Highlights: • We investigated the degradation kinetics of trichloroethene by zerovalent nanoiron particles. • Electron efficiency of the tested particles was very low (about 3%). • The tested environmental conditions had no significant influence on the degradation kinetics and electron efficiency. • We conclude that particle type is more

  13. Electron efficiency of nZVI does not change with variation of environmental parameters

    International Nuclear Information System (INIS)

    Schöftner, Philipp; Waldner, Georg; Lottermoser, Werner; Stöger-Pollach, Michael; Freitag, Peter; Reichenauer, Thomas G.

    2015-01-01

    Nanoscale zero-valent iron particles (nZVI) are already applied for in-situ dechlorination of halogenated organic contaminants in the field. We performed batch experiments whereby trichloroethene (TCE) was dehalogenated by nZVI under different environmental conditions that are relevant in practice. The tested conditions include different ionic strengths, addition of polyelectrolytes (carboxymethylcellulose and ligninsulphonate), lowered temperature, dissolved oxygen and different particle contents. Particle properties were determined by Mössbauer spectroscopy, XRD, TEM, SEM, AAS and laser obscuration time measurements. TCE dehalogenation and H 2 evolution were decelerated by reduced ionic strength, addition of polyelectrolytes, temperature reduction, the presence of dissolved oxygen and reduced particle content. The partitioning of released electrons between reactions with the contaminant vs. with water (selectivity) was low, independent of the tested conditions. Basically out of hundred electrons that were released via nZVI oxidation only 3.1 ± 1.4 were used for TCE dehalogenation. Even lower selectivities were observed at TCE concentrations below 3.5 mg l −1 , hence particle modifications and/or combination of nZVI with other remediation technologies seem to be necessary to reach target concentrations for remediation. Our results suggest that selectivity is particle intrinsic and not as much condition dependent, hence particle synthesis and potential particle modifications of nZVI particles may be more important for optimization of the pollutant degradation rate, than tested environmental conditions. - Highlights: • We investigated the degradation kinetics of trichloroethene by zerovalent nanoiron particles. • Electron efficiency of the tested particles was very low (about 3%). • The tested environmental conditions had no significant influence on the degradation kinetics and electron efficiency. • We conclude that particle type is more important for

  14. Influence of environmental parameters on the frictional behavior of DLC coatings

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y. [Louisiana State Univ., Baton Rouge, LA (United States). Mechanical Engineering Dept.; Erdemir, A.; Meletis, E.I. [Argonne National Lab., IL (United States). Energy Technology Div.

    1997-05-01

    In a previous studies it was shown that diamond like carbon (DLC) films possess low friction coefficient (f) and excellent wear resistance. The reduction in f was found to be consistent with a ``wear induced graphitization`` mechanism of the DLC structure. A recent study showed that operational parameters (sliding velocity and loading level) influence the tribological behavior of DLC film through control of the kinetics of the graphitization process. The objective of the present study was to investigate the influence of environmental parameters (humidity and temperature) on the tribological behavior of DLC film and provide further support to the wear induced graphitization mechanism. Ion beam deposition was utilized to deposit DLC on a SiC substrate. Pin-on-disc experiments were conducted by varying humidity (0%, 40% and 100%) and temperature ({minus}10 C and 25 C). As-deposited DLC and wear debris was characterized by transmission electron microscopy. It was found that lower humidity increases the graphitization rate more than likely due to the reduction in the effect by the water molecules. A decreased graphitization rate was observed at lower temperature and higher humidity and can be attributed to suppression of temperature rise at hot spots. The present findings are consistent with and further verify the wear induced graphitization mechanism.

  15. Environmental Impacts on the Strength Parameters of Mineral-Acrylic (PMMA/ATH Facade Panels

    Directory of Open Access Journals (Sweden)

    Aleksander Byrdy

    2015-01-01

    Full Text Available Composite mineral-acrylic panels consist in 80% of natural minerals produced from bauxite (aluminium hydroxides (ATH and in 20% from acrylic resin (polymethyl methacrylate (PMMA. This material due to high usability is widely used in interior finishes. Recently, the mineral-acrylic panels have been used as external claddings of buildings. So far, there are several dozen elevations realized worldwide. Due to the variability of the strength parameters of PMMA acrylic resins depending on the environmental influence, a number of tests on samples of mineral-acrylic panels to verify their suitability for use in climate conditions in Central Europe were performed. The studies determined the change of the material parameters after being subjected to aging process in conditions of high temperature, high relative humidity, freeze-thaw cycles, and UV radiation. In the studies parameters such as flexural strength and modulus of elasticity were measured at a reference temperature of 23°C. In raised and lowered temperatures only the tensile strength tests were conducted. Due to the lack of information in the available literature, the authors carried out tests of the temperature influence on the PMMA/ATH composite modulus of elasticity and flexural strength which is crucial in designing process.

  16. Practical device-independent quantum cryptography via entropy accumulation.

    Science.gov (United States)

    Arnon-Friedman, Rotem; Dupuis, Frédéric; Fawzi, Omar; Renner, Renato; Vidick, Thomas

    2018-01-31

    Device-independent cryptography goes beyond conventional quantum cryptography by providing security that holds independently of the quality of the underlying physical devices. Device-independent protocols are based on the quantum phenomena of non-locality and the violation of Bell inequalities. This high level of security could so far only be established under conditions which are not achievable experimentally. Here we present a property of entropy, termed "entropy accumulation", which asserts that the total amount of entropy of a large system is the sum of its parts. We use this property to prove the security of cryptographic protocols, including device-independent quantum key distribution, while achieving essentially optimal parameters. Recent experimental progress, which enabled loophole-free Bell tests, suggests that the achieved parameters are technologically accessible. Our work hence provides the theoretical groundwork for experimental demonstrations of device-independent cryptography.

  17. Biometric parameters of the bream (Abramis brama) as indicators for long-term changes in fish health and environmental quality--data from the German ESB.

    Science.gov (United States)

    Teubner, Diana; Paulus, Martin; Veith, Michael; Klein, Roland

    2015-02-01

    Piscifaunal health depends upon the state and quality of the aquatic environment. Variations in physical condition of fish may therefore be attributed to changes in environmental quality. Based on time series of up to 20 years of biometric data of bream from multiple sampling sites of the German environmental specimen bank (ESB), this study assessed whether changes in biometric parameters are able to indicate long-term alterations in fish health and environmental quality. Evaluated biometric parameters of fish health comprised length and weight of individuals of a defined age class, the condition factor, lipid content and hepatosomatic index (HSI). Although there are negative trends of the HSI, the overall development of health parameters can be interpreted as positive. This seems to suggest that health parameters conclusively mirror the long-term improvement of water quality in the selected rivers. However, the applicability of the condition factor as well as lipid content as indicators for fish health remained subject to restrictions. Altogether, the results from the ESB confirmed the high value of biometric parameters for monitoring of long-term changes in state and quality of aquatic ecosystems.

  18. Basic Earth's Parameters as estimated from VLBI observations

    Directory of Open Access Journals (Sweden)

    Ping Zhu

    2017-11-01

    Full Text Available The global Very Long Baseline Interferometry observation for measuring the Earth rotation's parameters was launched around 1970s. Since then the precision of the measurements is continuously improving by taking into account various instrumental and environmental effects. The MHB2000 nutation model was introduced in 2002, which is constructed based on a revised nutation series derived from 20 years VLBI observations (1980–1999. In this work, we firstly estimated the amplitudes of all nutation terms from the IERS-EOP-C04 VLBI global solutions w.r.t. IAU1980, then we further inferred the BEPs (Basic Earth's Parameters by fitting the major nutation terms. Meanwhile, the BEPs were obtained from the same nutation time series using a BI (Bayesian Inversion. The corrections to the precession rate and the estimated BEPs are in an agreement, independent of which methods have been applied.

  19. Thermal Orbital Environmental Parameter Study on the Propulsive Small Expendable Deployer System (ProSEDS) Using Earth Radiation Budget Experiment (ERBE) Data

    Science.gov (United States)

    Sharp, John R.; McConnaughey, Paul K. (Technical Monitor)

    2002-01-01

    The natural thermal environmental parameters used on the Space Station Program (SSP 30425) were generated by the Space Environmental Effects Branch at NASA's Marshall Space Flight Center (MSFC) utilizing extensive data from the Earth Radiation Budget Experiment (ERBE), a series of satellites which measured low earth orbit (LEO) albedo and outgoing long-wave radiation. Later, this temporal data was presented as a function of averaging times and orbital inclination for use by thermal engineers in NASA Technical Memorandum TM 4527. The data was not presented in a fashion readily usable by thermal engineering modeling tools and required knowledge of the thermal time constants and infrared versus solar spectrum sensitivity of the hardware being analyzed to be used properly. Another TM was recently issued as a guideline for utilizing these environments (NASA/TM-2001-211221) with more insight into the utilization by thermal analysts. This paper gives a top-level overview of the environmental parameters presented in the TM and a study of the effects of implementing these environments on an ongoing MSFC project, the Propulsive Small Expendable Deployer System (ProSEDS), compared to conventional orbital parameters that had been historically used.

  20. Toxicity challenges in environmental chemicals: Prediction of ...

    Science.gov (United States)

    Physiologically based pharmacokinetic (PBPK) models bridge the gap between in vitro assays and in vivo effects by accounting for the adsorption, distribution, metabolism, and excretion of xenobiotics, which is especially useful in the assessment of human toxicity. Quantitative structure-activity relationships (QSAR) serve as a vital tool for the high-throughput prediction of chemical-specific PBPK parameters, such as the fraction of a chemical unbound by plasma protein (Fub). The presented work explores the merit of utilizing experimental pharmaceutical Fub data for the construction of a universal QSAR model, in order to compensate for the limited range of high-quality experimental Fub data for environmentally relevant chemicals, such as pollutants, pesticides, and consumer products. Independent QSAR models were constructed with three machine-learning algorithms, k nearest neighbors (kNN), random forest (RF), and support vector machine (SVM) regression, from a large pharmaceutical training set (~1000) and assessed with independent test sets of pharmaceuticals (~200) and environmentally relevant chemicals in the ToxCast program (~400). Small descriptor sets yielded the optimal balance of model complexity and performance, providing insight into the biochemical factors of plasma protein binding, while preventing over fitting to the training set. Overlaps in chemical space between pharmaceutical and environmental compounds were considered through applicability of do

  1. The use of autecological and environmental parameters for establishing the status of lichen vegetation in a baseline study for a long-term monitoring survey

    International Nuclear Information System (INIS)

    Gombert, S.; Asta, J.; Seaward, M.R.D.

    2005-01-01

    In 1997 the ecological characteristics of the epiphytic species (83 lichens and two algae) of an urban area (Grenoble, France) were determined. Seven autecological indices were used to characterize the lichen ecology: illumination index, humidity index, pH of bark, nutrient status of substratum, ecological index of IAP and frequency. Six clusters (A1-A6) were defined using cluster analysis and principal component analysis. Seven environmental parameters characterizing the stations and the lichen releves were also used: elevation, parameters of artificiality (urbanization, traffic and local land use), IAP, and the percentage of nitrophytic and acidophytic species. Six clusters (B1-B6) were defined using cluster analysis and canonical correspondence analysis. Four clusters (C1-C4) were finally defined using an empirical integrated method combining the autecological and environmental parameters. This final clustering which established the status of the lichen vegetation in 1997 can be reliably used as a baseline study to effectively monitor environmental changes in this urban area. - Ecological clustering which establishes the status of lichen vegetation can be reliably used as a baseline study to monitor environmental changes

  2. Multivariate benthic ecosystem functioning in the Arctic – benthic fluxes explained by environmental parameters in the southeastern Beaufort Sea

    Directory of Open Access Journals (Sweden)

    H. Link

    2013-09-01

    Full Text Available The effects of climate change on Arctic marine ecosystems and their biogeochemical cycles are difficult to predict given the complex physical, biological and chemical interactions among the ecosystem components. We studied benthic biogeochemical fluxes in the Arctic and the influence of short-term (seasonal to annual, long-term (annual to decadal and other environmental variability on their spatial distribution to provide a baseline for estimates of the impact of future changes. In summer 2009, we measured fluxes of dissolved oxygen, nitrate, nitrite, ammonia, soluble reactive phosphate and silicic acid at the sediment–water interface at eight sites in the southeastern Beaufort Sea at water depths from 45 to 580 m. The spatial pattern of the measured benthic boundary fluxes was heterogeneous. Multivariate analysis of flux data showed that no single or reduced combination of fluxes could explain the majority of spatial variation, indicating that oxygen flux is not representative of other nutrient sink–source dynamics. We tested the influence of eight environmental parameters on single benthic fluxes. Short-term environmental parameters (sinking flux of particulate organic carbon above the bottom, sediment surface Chl a were most important for explaining oxygen, ammonium and nitrate fluxes. Long-term parameters (porosity, surface manganese and iron concentration, bottom water oxygen concentrations together with δ13Corg signature explained most of the spatial variation in phosphate, nitrate and nitrite fluxes. Variation in pigments at the sediment surface was most important to explain variation in fluxes of silicic acid. In a model including all fluxes synchronously, the overall spatial distribution could be best explained (57% by the combination of sediment Chl a, phaeopigments, δ13Corg, surficial manganese and bottom water oxygen concentration. We conclude that it is necessary to consider long-term environmental variability along with

  3. Development and Substantiation of Parameters of Environmentally Friendly Technology for Filling the Vertical Mine Workings with Autoclaved Slag-Concrete

    Directory of Open Access Journals (Sweden)

    Uglyanitca Andrey

    2017-01-01

    Full Text Available The environmentally friendly technology for filling the vertical mine workings with autoclaved slag-concrete, prefabricated on the surface of the mine is presented in the article; the optimal parameters of filling technology are proposed. The developed technology for filling the abandoned vertical mine workings allows ensuring the environmental safety of the territories adjacent to the abandoned mine, utilizing slag dumps and providing the possibility of shaft recovery, if necessary, with minimal labor and material costs.

  4. Metabolic heat production and thermal conductance are mass-independent adaptations to thermal environment in birds and mammals.

    Science.gov (United States)

    Fristoe, Trevor S; Burger, Joseph R; Balk, Meghan A; Khaliq, Imran; Hof, Christian; Brown, James H

    2015-12-29

    The extent to which different kinds of organisms have adapted to environmental temperature regimes is central to understanding how they respond to climate change. The Scholander-Irving (S-I) model of heat transfer lays the foundation for explaining how endothermic birds and mammals maintain their high, relatively constant body temperatures in the face of wide variation in environmental temperature. The S-I model shows how body temperature is regulated by balancing the rates of heat production and heat loss. Both rates scale with body size, suggesting that larger animals should be better adapted to cold environments than smaller animals, and vice versa. However, the global distributions of ∼9,000 species of terrestrial birds and mammals show that the entire range of body sizes occurs in nearly all climatic regimes. Using physiological and environmental temperature data for 211 bird and 178 mammal species, we test for mass-independent adaptive changes in two key parameters of the S-I model: basal metabolic rate (BMR) and thermal conductance. We derive an axis of thermal adaptation that is independent of body size, extends the S-I model, and highlights interactions among physiological and morphological traits that allow endotherms to persist in a wide range of temperatures. Our macrophysiological and macroecological analyses support our predictions that shifts in BMR and thermal conductance confer important adaptations to environmental temperature in both birds and mammals.

  5. A grey-forecasting interval-parameter mixed-integer programming approach for integrated electric-environmental management–A case study of Beijing

    International Nuclear Information System (INIS)

    Wang, Xingwei; Cai, Yanpeng; Chen, Jiajun; Dai, Chao

    2013-01-01

    In this study, a GFIPMIP (grey-forecasting interval-parameter mixed-integer programming) approach was developed for supporting IEEM (integrated electric-environmental management) in Beijing. It was an attempt to incorporate an energy-forecasting model within a general modeling framework at the municipal level. The developed GFIPMIP model can not only forecast electric demands, but also reflect dynamic, interactive, and uncertain characteristics of the IEEM system in Beijing. Moreover, it can address issues regarding power supply, and emission reduction of atmospheric pollutants and GHG (greenhouse gas). Optimal solutions were obtained related to power generation patterns and facility capacity expansion schemes under a series of system constraints. Two scenarios were analyzed based on multiple environmental policies. The results were useful for helping decision makers identify desired management strategies to guarantee the city's power supply and mitigate emissions of GHG and atmospheric pollutants. The results also suggested that the developed GFIPMIP model be applicable to similar engineering problems. - Highlights: • A grey-forecasting interval-parameter mixed integer programming (GFIPMIP) approach was developed. • It could reflect dynamic, interactive, and uncertain characteristics of an IEEM system. • The developed GFIPMIP approach was used for supporting IEEM system planning in Beijing. • Two scenarios were established based on different environmental policies and management targets. • Optimal schemes for power generation, energy supply, and environmental protection were identified

  6. Interval-parameter chance-constraint programming model for end-of-life vehicles management under rigorous environmental regulations.

    Science.gov (United States)

    Simic, Vladimir

    2016-06-01

    As the number of end-of-life vehicles (ELVs) is estimated to increase to 79.3 million units per year by 2020 (e.g., 40 million units were generated in 2010), there is strong motivation to effectively manage this fast-growing waste flow. Intensive work on management of ELVs is necessary in order to more successfully tackle this important environmental challenge. This paper proposes an interval-parameter chance-constraint programming model for end-of-life vehicles management under rigorous environmental regulations. The proposed model can incorporate various uncertainty information in the modeling process. The complex relationships between different ELV management sub-systems are successfully addressed. Particularly, the formulated model can help identify optimal patterns of procurement from multiple sources of ELV supply, production and inventory planning in multiple vehicle recycling factories, and allocation of sorted material flows to multiple final destinations under rigorous environmental regulations. A case study is conducted in order to demonstrate the potentials and applicability of the proposed model. Various constraint-violation probability levels are examined in detail. Influences of parameter uncertainty on model solutions are thoroughly investigated. Useful solutions for the management of ELVs are obtained under different probabilities of violating system constraints. The formulated model is able to tackle a hard, uncertainty existing ELV management problem. The presented model has advantages in providing bases for determining long-term ELV management plans with desired compromises between economic efficiency of vehicle recycling system and system-reliability considerations. The results are helpful for supporting generation and improvement of ELV management plans. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Investment requirements in the oil industry of the independent oil exporting countries in the face of environmental challenges

    International Nuclear Information System (INIS)

    Rahmat, H.; Hamid, A.A.

    1992-01-01

    The oil industry has to operate under environmental constraints which involve commercial risks. Oil companies need to treat environmental management as an investment as well as an insurance problem, assessing risks and costs and deciding how to minimize them most cost effectively. Petroleum development in Malaysia is accelerating. In view of the high visibility of the industry and the wide publicity generated by a few incidents which have taken place outside Malaysia the national oil company, Petronas, is constantly vigilant in its efforts to preserve the environment. Oil producing countries like Malaysia will need to continue to set aside some of the revenue they obtain from the oil industry and use it for protecting the environment to ensure public acceptance and ultimately, orderly growth of their industry. Clearly they are less able to do so if their income is lessened through the interference with free trade among nations even if the purported reasons for the interference is the environment itself. Ultimately the environmental investment requirement in the oil industry of the independent and developing oil exporting countries is free trade without price distortions. The 1989 Langkawi Declaration on the Environment of the Commonwealth Heads of Government is appended to this article. (author)

  8. Monitoring of conventional environmental parameters at CERN Annual Report 2003

    CERN Document Server

    Kleiner, S

    2004-01-01

    The monitoring programme for conventional environmental parameters at CERN comprises the control of water released from CERN installations, checks of water quality in rivers receiving water from CERN and monitoring of ambient air quality at places close to the CERN sites. The control of released water includes continuous monitoring of pH and temperature at six CERN water outlets and periodical sampling and analysis campaigns to check in more details the quality of the water released from the CERN sites. Regular measurements of pH, temperature, concentration of dissolved oxygen and conductivity were performed in the water of the rivers Nant d'Avril (CH) and Le Lion (F) as well as in the water of the streams around the seven LHC sites PA2 − PA8. The concentrations of nitrogen oxides and ozone in the ambient air, which may be produced in accelerator facilities and released into the environment, were measured at two off-site monitoring stations in Maisonnex (CH) and Cessy (F). The report summarises the results ...

  9. Monitoring of conventional environmental parameters at CERN Annual Report 2004

    CERN Document Server

    Dziewa, A

    2005-01-01

    The monitoring programme for conventional environmental parameters at CERN comprises the control of water released from CERN installations, checks of water quality in rivers receiving water from CERN and monitoring of ambient air quality at places close to the CERN sites. The control of released water includes continuous monitoring of pH and temperature at six CERN water outlets and periodical sampling and analysis campaigns to check in more details the quality of the water released from the CERN sites. Sporadic river-water analyses and regular measurements of pH, temperature, concentration of dissolved oxygen and conductivity, were performed in the water of the rivers Nant d'Avril (CH) and Le Lion (F) as well as in the water of the streams around the seven LHC sites PA2 − PA8. The concentrations of nitrogen oxides and ozone in the ambient air, which may be produced in accelerator facilities and released into the environment, were measured at two off-site monitoring stations in Maisonnex (CH) and Cessy (F)....

  10. Approaches in highly parameterized inversion - PEST++, a Parameter ESTimation code optimized for large environmental models

    Science.gov (United States)

    Welter, David E.; Doherty, John E.; Hunt, Randall J.; Muffels, Christopher T.; Tonkin, Matthew J.; Schreuder, Willem A.

    2012-01-01

    An object-oriented parameter estimation code was developed to incorporate benefits of object-oriented programming techniques for solving large parameter estimation modeling problems. The code is written in C++ and is a formulation and expansion of the algorithms included in PEST, a widely used parameter estimation code written in Fortran. The new code is called PEST++ and is designed to lower the barriers of entry for users and developers while providing efficient algorithms that can accommodate large, highly parameterized problems. This effort has focused on (1) implementing the most popular features of PEST in a fashion that is easy for novice or experienced modelers to use and (2) creating a software design that is easy to extend; that is, this effort provides a documented object-oriented framework designed from the ground up to be modular and extensible. In addition, all PEST++ source code and its associated libraries, as well as the general run manager source code, have been integrated in the Microsoft Visual Studio® 2010 integrated development environment. The PEST++ code is designed to provide a foundation for an open-source development environment capable of producing robust and efficient parameter estimation tools for the environmental modeling community into the future.

  11. Bayesian Independent Component Analysis

    DEFF Research Database (Denmark)

    Winther, Ole; Petersen, Kaare Brandt

    2007-01-01

    In this paper we present an empirical Bayesian framework for independent component analysis. The framework provides estimates of the sources, the mixing matrix and the noise parameters, and is flexible with respect to choice of source prior and the number of sources and sensors. Inside the engine...

  12. Management of environmental risks associated with landfills in seismically active regions in the New Independent States of Central Asia

    International Nuclear Information System (INIS)

    Webb, S.M.

    2009-01-01

    Sustainable waste management and disposal is a societal challenge in terms of economics, public health and environmental impact. The situation in developing countries, and in particular those subject to extreme natural hazards, results in increased overall risk as governments prioritize investments to issues of perceived higher economic importance. This dissertation investigates environmental risks associated with landfills in seismically active regions in the New Independent States of Central Asia. Environmental risk from municipal solid waste landfill sites encompasses a wide range of topics within socio-economics, physical sciences and engineering and therefore necessitates a multi-disciplinary approach. The underlying study is an accumulative result of a three-year collaborative research project (Contract No. INCO-CT-2005-516732) funded within the Eu Sixth Framework Programme (FP6). The international cooperation involved European, Russian and Central Asian research partners forming a multi-disciplinary consortium covering: GIS technologies, geology / hydrogeology geophysics and geotechnical engineering; landfill design and operation and waste management. understanding the relevant socio-economic aspects and legislative frameworks was necessary to prepare results and recommendations to address stakeholders in the Central Asian countries: Kazakhstan, Kyrgyzstan,Tajikistan,Turkmenistan and uzbekistan. (author) [de

  13. Do It Yourself solution of Internet of Things Healthcare System: Measuring body parameters and environmental parameters affecting health.

    Directory of Open Access Journals (Sweden)

    Mirjana Maksimović

    2016-03-01

    Full Text Available The rapid advancements in information and communications technologies (ICT and the increasing number of smart things shift an old-fashioned healthcare system to a model better suited for a population of the 21st century. New healthcare approaches based on Internet of Things (IoT/Internet of Medical Things (IoMT powered systems make health monitoring, diagnostics and treatment more personalized, timely and convenient, enabling a global approach to the healthcare system infrastructure development. Commercial systems in this area exist in various forms but usually do not fit the general patient needs, and those that do are usually economically unacceptable due to the high operational and development costs. Do It Yourself (DIY healthcare, including mobile applications and consumer medical devices, nowadays is the top healthcare trend. Therefore, this paper, based on well-known low-cost technologies, presents a DIY IoMT solution for observing human vital parameter as well as environmental factors affecting health.

  14. A Generic Approach to Parameter Control

    NARCIS (Netherlands)

    Karafotias, G.; Smit, S.K.; Eiben, A.E.

    2012-01-01

    On-line control of EA parameters is an approach to parameter setting that offers the advantage of values changing during the run. In this paper, we investigate parameter control from a generic and parameter-independent perspective. We propose a generic control mechanism that is targeted to

  15. Effects of demographic structure on key properties of stochastic density-independent population dynamics.

    Science.gov (United States)

    Vindenes, Yngvild; Sæther, Bernt-Erik; Engen, Steinar

    2012-12-01

    The development of stochastic demography has largely been based on age structured populations, although other types of demographic structure, especially permanent and dynamic heterogeneity, are likely common in natural populations. The combination of stochasticity and demographic structure is a challenge for analyses of population dynamics and extinction risk, because the population structure will fluctuate around the stable structure and the population size shows transient fluctuations. However, by using a diffusion approximation for the total reproductive value, density-independent dynamics of structured populations can be described with only three population parameters: the expected population growth rate, the environmental variance and the demographic variance. These parameters depend on population structure via the state-specific vital rates and transition rates. Once they are found, the diffusion approximation represents a substantial reduction in model complexity. Here, we review and compare the key population parameters across a wide range of demographic structure, from the case of no structure to the most general case of dynamic heterogeneity, and for both discrete and continuous types. We focus on the demographic variance, but also show how environmental stochasticity can be included. This study brings together results from recent models, each considering a specific type of population structure, and places them in a general framework for structured populations. Comparison across different types of demographic structure reveals that the reproductive value is an essential concept for understanding how population structure affects stochastic dynamics and extinction risk. Copyright © 2011 Elsevier Inc. All rights reserved.

  16. Independent technical review, handbook

    International Nuclear Information System (INIS)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project

  17. Independent technical review, handbook

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project.

  18. Design parameters and source terms: Volume 1, Design parameters: Revision 0

    International Nuclear Information System (INIS)

    1987-10-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report by Stearns Catalytic Corporation (SCC), entitled ''Design Parameters and Source Terms for a Two-Phase Repository in Salt,'' 1985, to the level of the Site Characterization Plan - Conceptual Design Report. The previous unpublished SCC Study identifies the data needs for the Environmental Assessment effort for seven possible Salt Repository sites

  19. Redundant and physical black hole parameters: Is there an independent physical dilaton charge?

    Energy Technology Data Exchange (ETDEWEB)

    Hajian, K., E-mail: kamalhajian@ipm.ir; Sheikh-Jabbari, M.M., E-mail: jabbari@theory.ipm.ac.ir

    2017-05-10

    Black holes as solutions to gravity theories, are generically identified by a set of parameters. Some of these parameters are associated with black hole physical conserved charges, like ADM charges. There can also be some “redundant parameters.” We propose necessary conditions for a parameter to be physical. The conditions are essentially integrability and non-triviality of the charge variations arising from “parametric variations,” variation of the solution with respect to the chosen parameters. In addition, we prove that variation of the redundant parameters which do not meet our criteria do not appear in the first law of thermodynamics. As an interesting application, we show that dilaton moduli are redundant parameters for black hole solutions to Einstein–Maxwell–(Axion)–Dilaton theories, because variations in dilaton moduli would render entropy, mass, electric charges or angular momenta non-integrable. Our results are in contrast with modification of the first law due to scalar charges suggested in Gibbons–Kallosh–Kol paper and its follow-ups. We also briefly discuss implications of our results for the attractor behavior of extremal black holes.

  20. JPRS Report, Environmental Issues

    Science.gov (United States)

    1990-05-14

    To Lag Most on EC Environmental Norms [Madrid EL INDEPENDIENTE 9 Feb] ... 92 Mediterranean’Environmental Disaster’Discussed [Nicosia CYPRUS MAIL...etiquette. The independence of scientific thinking was logically transformed into independence in his public position. A WASHINGTON POST correspondent...the post -war restoration of the national economy were associated with the necessity of providing people and industry with everything needed—coal

  1. Method-independent, Computationally Frugal Convergence Testing for Sensitivity Analysis Techniques

    Science.gov (United States)

    Mai, J.; Tolson, B.

    2017-12-01

    The increasing complexity and runtime of environmental models lead to the current situation that the calibration of all model parameters or the estimation of all of their uncertainty is often computationally infeasible. Hence, techniques to determine the sensitivity of model parameters are used to identify most important parameters. All subsequent model calibrations or uncertainty estimation procedures focus then only on these subsets of parameters and are hence less computational demanding. While the examination of the convergence of calibration and uncertainty methods is state-of-the-art, the convergence of the sensitivity methods is usually not checked. If any, bootstrapping of the sensitivity results is used to determine the reliability of the estimated indexes. Bootstrapping, however, might as well become computationally expensive in case of large model outputs and a high number of bootstraps. We, therefore, present a Model Variable Augmentation (MVA) approach to check the convergence of sensitivity indexes without performing any additional model run. This technique is method- and model-independent. It can be applied either during the sensitivity analysis (SA) or afterwards. The latter case enables the checking of already processed sensitivity indexes. To demonstrate the method's independency of the convergence testing method, we applied it to two widely used, global SA methods: the screening method known as Morris method or Elementary Effects (Morris 1991) and the variance-based Sobol' method (Solbol' 1993). The new convergence testing method is first scrutinized using 12 analytical benchmark functions (Cuntz & Mai et al. 2015) where the true indexes of aforementioned three methods are known. This proof of principle shows that the method reliably determines the uncertainty of the SA results when different budgets are used for the SA. The results show that the new frugal method is able to test the convergence and therefore the reliability of SA results in an

  2. Assessment of the Eutrophication-Related Environmental Parameters in Two Mediterranean Lakes by Integrating Statistical Techniques and Self-Organizing Maps.

    Science.gov (United States)

    Hadjisolomou, Ekaterini; Stefanidis, Konstantinos; Papatheodorou, George; Papastergiadou, Evanthia

    2018-03-19

    During the last decades, Mediterranean freshwater ecosystems, especially lakes, have been under severe pressure due to increasing eutrophication and water quality deterioration. In this article, we compared the effectiveness of different data analysis methods by assessing the contribution of environmental parameters to eutrophication processes. For this purpose, principal components analysis (PCA), cluster analysis, and a self-organizing map (SOM) were applied, using water quality data from two transboundary lakes of North Greece. SOM is considered as an advanced and powerful data analysis tool because of its ability to represent complex and nonlinear relationships among multivariate data sets. The results of PCA and cluster analysis agreed with the SOM results, although the latter provided more information because of the visualization abilities regarding the parameters' relationships. Besides nutrients that were found to be a key factor for controlling chlorophyll-a (Chl - a), water temperature was related positively with algal production, while the Secchi disk depth parameter was found to be highly important and negatively related toeutrophic conditions. In general, the SOM results were more specific and allowed direct associations between the water quality variables. Our work showed that SOMs can be used effectively in limnological studies to produce robust and interpretable results, aiding scientists and managers to cope with environmental problems such as eutrophication.

  3. Model evaluation methodology applicable to environmental assessment models

    International Nuclear Information System (INIS)

    Shaeffer, D.L.

    1979-08-01

    A model evaluation methodology is presented to provide a systematic framework within which the adequacy of environmental assessment models might be examined. The necessity for such a tool is motivated by the widespread use of models for predicting the environmental consequences of various human activities and by the reliance on these model predictions for deciding whether a particular activity requires the deployment of costly control measures. Consequently, the uncertainty associated with prediction must be established for the use of such models. The methodology presented here consists of six major tasks: model examination, algorithm examination, data evaluation, sensitivity analyses, validation studies, and code comparison. This methodology is presented in the form of a flowchart to show the logical interrelatedness of the various tasks. Emphasis has been placed on identifying those parameters which are most important in determining the predictive outputs of a model. Importance has been attached to the process of collecting quality data. A method has been developed for analyzing multiplicative chain models when the input parameters are statistically independent and lognormally distributed. Latin hypercube sampling has been offered as a promising candidate for doing sensitivity analyses. Several different ways of viewing the validity of a model have been presented. Criteria are presented for selecting models for environmental assessment purposes

  4. On-shell gauge-parameter independence of contributions to electroweak quark self-energies

    International Nuclear Information System (INIS)

    Ahmady, M.R.; Elias, V.; Mendel, R.R.; Scadron, M.D.; Steele, T.

    1989-01-01

    We allow an external condensate to enter standard SU(2) x U(1) electroweak theory via the vacuum expectation value , as in QCD sum-rule applications. For a given flavor, we then find that any gauge-parameter dependence of quark self-energies on the ''mass shell'' is eliminated provided that the mass shell is made to coincide with both the expansion-parameter mass occurring in the operator-product expansion of and the standard electroweak mass acquired via the Yukawa coupling to the usual scalar vacuum expectation value of spontaneous symmetry breaking. This result indicates that if the QCD-generated order parameter and associated dynamical mass(es) m/sub q//sup dyn/ are utilized as external input parameters in electroweak calculations involving hadrons, then new corrections must be introduced into the q-barqW and q-barqZ vertices in order to preserve SU(2) x U(1) Ward identities

  5. Redundant and physical black hole parameters: Is there an independent physical dilaton charge?

    Directory of Open Access Journals (Sweden)

    K. Hajian

    2017-05-01

    Full Text Available Black holes as solutions to gravity theories, are generically identified by a set of parameters. Some of these parameters are associated with black hole physical conserved charges, like ADM charges. There can also be some “redundant parameters.” We propose necessary conditions for a parameter to be physical. The conditions are essentially integrability and non-triviality of the charge variations arising from “parametric variations,” variation of the solution with respect to the chosen parameters. In addition, we prove that variation of the redundant parameters which do not meet our criteria do not appear in the first law of thermodynamics. As an interesting application, we show that dilaton moduli are redundant parameters for black hole solutions to Einstein–Maxwell–(Axion–Dilaton theories, because variations in dilaton moduli would render entropy, mass, electric charges or angular momenta non-integrable. Our results are in contrast with modification of the first law due to scalar charges suggested in Gibbons–Kallosh–Kol paper [1] and its follow-ups. We also briefly discuss implications of our results for the attractor behavior of extremal black holes.

  6. The effects of environmental parameters on zooplankton assemblages in tropical coastal estuary, South-west, Nigeria

    Directory of Open Access Journals (Sweden)

    Waidi O. Abdul

    2016-09-01

    Full Text Available The present study was carried out to examine the distribution and assemblage structure of zooplankton in relation to environmental parameters of tropical coastal estuarine ecosystem impounding Bight of Benin, Nigeria. The estuarine water samples were collected between January and December, 2014 from three sampling zones (Brushpark, Open water and Wetland then were fixed in 4% formalin. A total of twenty-eight (28 species belonging to four (4 groups were recorded in this study. These groups were rotifera, copepoda, cladocerans and ostracodas, and were all widely distributed in the three investigated zones. Higher richness, dominance and abundance indices were recorded in Zone I when compared to both Zones II and III. Cluster analysis showed five distinct species communities. The canonical correspondence analysis (CCA showed a distinct smattering positive and negative correlation on the distribution of zooplankton indicating that the relative abundance of any species was dependent on specific environmental variables.

  7. Direct Yaw-Moment Control of All-Wheel-Independent-Drive Electric Vehicles with Network-Induced Delays through Parameter-Dependent Fuzzy SMC Approach

    Directory of Open Access Journals (Sweden)

    Wanke Cao

    2017-01-01

    Full Text Available This paper investigates the robust direct yaw-moment control (DYC through parameter-dependent fuzzy sliding mode control (SMC approach for all-wheel-independent-drive electric vehicles (AWID-EVs subject to network-induced delays. AWID-EVs have obvious advantages in terms of DYC over the traditional centralized-drive vehicles. However it is one of the most principal issues for AWID-EVs to ensure the robustness of DYC. Furthermore, the network-induced delays would also reduce control performance of DYC and even deteriorate the EV system. To ensure robustness of DYC and deal with network-induced delays, a parameter-dependent fuzzy sliding mode control (FSMC method based on the real-time information of vehicle states and delays is proposed in this paper. The results of cosimulations with Simulink® and CarSim® demonstrate the effectiveness of the proposed controller. Moreover, the results of comparison with a conventional FSMC controller illustrate the strength of explicitly dealing with network-induced delays.

  8. Massively Parallel Dimension Independent Adaptive Metropolis

    KAUST Repository

    Chen, Yuxin

    2015-01-01

    parameter dimension, by respecting the variance, for Gaussian targets. The result- ing algorithm, referred to as the dimension-independent adaptive Metropolis (DIAM) algorithm, also shows improved performance with respect to adaptive Metropolis on non

  9. Semen parameters can be predicted from environmental factors and lifestyle using artificial intelligence methods.

    Science.gov (United States)

    Girela, Jose L; Gil, David; Johnsson, Magnus; Gomez-Torres, María José; De Juan, Joaquín

    2013-04-01

    Fertility rates have dramatically decreased in the last two decades, especially in men. It has been described that environmental factors as well as life habits may affect semen quality. In this paper we use artificial intelligence techniques in order to predict semen characteristics resulting from environmental factors, life habits, and health status, with these techniques constituting a possible decision support system that can help in the study of male fertility potential. A total of 123 young, healthy volunteers provided a semen sample that was analyzed according to the World Health Organization 2010 criteria. They also were asked to complete a validated questionnaire about life habits and health status. Sperm concentration and percentage of motile sperm were related to sociodemographic data, environmental factors, health status, and life habits in order to determine the predictive accuracy of a multilayer perceptron network, a type of artificial neural network. In conclusion, we have developed an artificial neural network that can predict the results of the semen analysis based on the data collected by the questionnaire. The semen parameter that is best predicted using this methodology is the sperm concentration. Although the accuracy for motility is slightly lower than that for concentration, it is possible to predict it with a significant degree of accuracy. This methodology can be a useful tool in early diagnosis of patients with seminal disorders or in the selection of candidates to become semen donors.

  10. Failure probability under parameter uncertainty.

    Science.gov (United States)

    Gerrard, R; Tsanakas, A

    2011-05-01

    In many problems of risk analysis, failure is equivalent to the event of a random risk factor exceeding a given threshold. Failure probabilities can be controlled if a decisionmaker is able to set the threshold at an appropriate level. This abstract situation applies, for example, to environmental risks with infrastructure controls; to supply chain risks with inventory controls; and to insurance solvency risks with capital controls. However, uncertainty around the distribution of the risk factor implies that parameter error will be present and the measures taken to control failure probabilities may not be effective. We show that parameter uncertainty increases the probability (understood as expected frequency) of failures. For a large class of loss distributions, arising from increasing transformations of location-scale families (including the log-normal, Weibull, and Pareto distributions), the article shows that failure probabilities can be exactly calculated, as they are independent of the true (but unknown) parameters. Hence it is possible to obtain an explicit measure of the effect of parameter uncertainty on failure probability. Failure probability can be controlled in two different ways: (1) by reducing the nominal required failure probability, depending on the size of the available data set, and (2) by modifying of the distribution itself that is used to calculate the risk control. Approach (1) corresponds to a frequentist/regulatory view of probability, while approach (2) is consistent with a Bayesian/personalistic view. We furthermore show that the two approaches are consistent in achieving the required failure probability. Finally, we briefly discuss the effects of data pooling and its systemic risk implications. © 2010 Society for Risk Analysis.

  11. Model-independent cosmological constraints from growth and expansion

    Science.gov (United States)

    L'Huillier, Benjamin; Shafieloo, Arman; Kim, Hyungjin

    2018-05-01

    Reconstructing the expansion history of the Universe from Type Ia supernovae data, we fit the growth rate measurements and put model-independent constraints on some key cosmological parameters, namely, Ωm, γ, and σ8. The constraints are consistent with those from the concordance model within the framework of general relativity, but the current quality of the data is not sufficient to rule out modified gravity models. Adding the condition that dark energy density should be positive at all redshifts, independently of its equation of state, further constrains the parameters and interestingly supports the concordance model.

  12. Estimates of genetic parameters and environmental effects for measures of hunting performance in Finnish hounds.

    Science.gov (United States)

    Liinamo, A E; Karjalainen, L; Ojala, M; Vilva, V

    1997-03-01

    Data from field trials of Finnish Hounds between 1988 and 1992 in Finland were used to estimate genetic parameters and environmental effects for measures of hunting performance using REML procedures and an animal model. The original data set included 28,791 field trial records from 5,666 dogs. Males and females had equal hunting performance, whereas experience acquired by age improved trial results compared with results for young dogs (P Hounds with respect to their hunting ability should be based on animal model BLUP methods instead of mere performance testing. The evaluation system of field trials should also be revised for more reliability.

  13. Evaluation of selected predictive models and parameters for the environmental transport and dosimetry of radionuclides

    International Nuclear Information System (INIS)

    Miller, C.W.; Dunning, D.E. Jr.; Etnier, E.L.; Hoffman, F.O.; Little, C.A.; Meyer, H.R.; Shaeffer, D.L.; Till, J.E.

    1979-07-01

    Evaluations of selected predictive models and parameters used in the assessment of the environmental transport and dosimetry of radionuclides are summarized. Mator sections of this report include a validation of the Gaussian plume disperson model, comparison of the output of a model for the transport of 131 I from vegetation to milk with field data, validation of a model for the fraction of aerosols intercepted by vegetation, an evaluation of dose conversion factors for 232 Th, an evaluation of considering the effect of age dependency on population dose estimates, and a summary of validation results for hydrologic transport models

  14. The Trade Off Between Central Bank Independence and Conservativeness

    NARCIS (Netherlands)

    Eijffinger, S.C.W.; Hoeberichts, M.M.

    1996-01-01

    This paper introduces a parameter for central bank independence in a monetary policy game with a conservative central banker.It tries to explain the optimal degree of central bank independence and conservativeness by four economic and political determinants, both theoretically and empirically.There

  15. Documentation of Hanford Site independent review of the Hanford Waste Vitrification Plant Preliminary Safety Analysis Report

    International Nuclear Information System (INIS)

    Herborn, D.I.

    1991-10-01

    The requirements for Westinghouse Hanford independent review of the Preliminary Safety Analysis Report (PSAR) are contained in Section 1.0, Subsection 4.3 of WCH-CM-4-46. Specifically, this manual requires the following: (1) Formal functional reviews of the HWVP PSAR by the future operating organization (HWVP Operations), and the independent review organizations (HWVP and Environmental Safety Assurance, Environmental Assurance, and Quality Assurance); and (2) Review and approval of the HWVP PSAR by the Tank Waste Disposal (TWD) Subcouncil of the Safety and Environmental Advisory Council (SEAC), which provides independent advice to the Westinghouse Hanford President and executives on matters of safety and environmental protection. 7 refs

  16. Achieving scale-independent land-surface flux estimates - Application of the Multiscale Parameter Regionalization (MPR) to the Noah-MP land-surface model across the contiguous USA

    Science.gov (United States)

    Thober, S.; Mizukami, N.; Samaniego, L. E.; Attinger, S.; Clark, M. P.; Cuntz, M.

    2016-12-01

    Land-surface models use a variety of process representations to calculate terrestrial energy, water and biogeochemical fluxes. These process descriptions are usually derived from point measurements but are scaled to much larger resolutions in applications that range from about 1 km in catchment hydrology to 100 km in climate modelling. Both, hydrologic and climate models are nowadays run on different spatial resolutions, using the exact same land surface representations. A fundamental criterion for the physical consistency of land-surface simulations across scales is that a flux estimated over a given area is independent of the spatial model resolution (i.e., the flux-matching criterion). The Noah-MP land surface model considers only one soil and land cover type per model grid cell without any representation of subgrid variability, implying a weak flux-matching. A fractional approach simulates subgrid variability but it requires a higher computational demand than using effective parameters and it is used only for land cover in current land surface schemes. A promising approach to derive scale-independent parameters is the Multiscale Parameter Regionalization (MPR) technique, which consists of two steps: first, it applies transfer functions directly to high-resolution data (such as 100 m soil maps) to derive high-resolution model parameter fields, acknowledging the full subgrid variability. Second, it upscales these high-resolution parameter fields to the model resolution by using appropriate upscaling operators. MPR has shown to improve substantially the scalability of hydrologic models. Here, we apply the MPR technique to the Noah-MP land-surface model for a large sample of basins distributed across the contiguous USA. Specifically, we evaluate the flux-matching criterion for several hydrologic fluxes such as evapotranspiration and total runoff at scales ranging from 3 km to 48 km. We also investigate a p-norm scaling operator that goes beyond the current

  17. Examination advice of the location-independent Environmental-impact report and advice-direction guides for the location-dependent environmental-impact report concerning storage and processing of radioactive waste

    International Nuclear Information System (INIS)

    1986-01-01

    This document is the examination advice made by the Provisional Committee for the environmental-impact reporting (VCmer) in view of the decision-making in behalf of which the location-independent environmental-impact report (MER) has been drawn up. Besides the examination by the VCmer of the location-independent MER in accordance with article 41z, part 1 and 2, this document covers an advice for direction guides for the, still to be drawn up, location-dependent MER on the storage and processing of radioactive wastes produced in the Netherlands, in accordance with article 41n, part 1 of the enactment m.e.r. The MER has been drawn up in behalf of the decision-making about location, design and construction of an aboveground, temporal storage of radioactive waste for the coming 50-100 years. In the MER two scenarios are distinguished: scenario 1 in fact reflects the actual situation in which, besides the amount of low- and medium-level radioactive waste, the high-level radioactive waste from the two nuclear power plants in the Netherlands have to be taken into account. Scenario 2 includes, besides the waste production of scenario 1, an extension with regard to the waste which would be produced in a 30-year operation time of a, still to be isntalled, nuclear power of 2000 MWe, to be increased up to 4000 MWe eventually. In this scenario finally about three quarter of the total volume of all radioactive waste would be produced by nuclear power plants. In that case emphasis will lay upon an installation which in particular has to be appropriate for a longtime, be it still temporary, storage of radioactive waste originating, largely, from the new nuclear power plant to be build in the Netherlands. (author)

  18. Effects of simulated space environmental parameters on six commercially available composite materials

    International Nuclear Information System (INIS)

    Funk, J.G.; Sykes, G.F. Jr.

    1989-04-01

    The effects of simulated space environmental parameters on microdamage induced by the environment in a series of commercially available graphite-fiber-reinforced composite materials were determined. Composites with both thermoset and thermoplastic resin systems were studied. Low-Earth-Orbit (LEO) exposures were simulated by thermal cycling; geosynchronous-orbit (GEO) exposures were simulated by electron irradiation plus thermal cycling. The thermal cycling temperature range was -250 F to either 200 F or 150 F. The upper limits of the thermal cycles were different to ensure that an individual composite material was not cycled above its glass transition temperature. Material response was characterized through assessment of the induced microcracking and its influence on mechanical property changes at both room temperature and -250 F. Microdamage was induced in both thermoset and thermoplastic advanced composite materials exposed to the simulated LEO environment. However, a 350 F cure single-phase toughened epoxy composite was not damaged during exposure to the LEO environment. The simuated GEO environment produced microdamage in all materials tested

  19. Environmental Assessment

    OpenAIRE

    The Inspection Panel

    2017-01-01

    The Inspection Panel, the World Bank’s independent accountability mechanism, has released the third report in its Emerging Lessons Series. The latest report identifies lessons from Panel cases related to environmental assessment (EA) issues. The Panel is an impartial fact-finding body, independent from the World Bank management and staff, reporting directly to the Board. In response to com...

  20. AC machine control : robust and sensorless control by parameter independency

    Energy Technology Data Exchange (ETDEWEB)

    Samuelsen, Dag Andreas Hals

    2009-06-15

    In this thesis it is first presented how robust control can be used to give AC motor drive systems competitive dynamic performance under parameter variations. These variations are common to all AC machines, and are a result of temperature change in the machine, and imperfect machine models. This robust control is, however, dependent on sensor operation in the sense that the rotor position is needed in the control loop. Elimination of this control loop has been for many years, and still is, a main research area of AC machines control systems. An integrated PWM modulator and sampler unit has been developed and tested. The sampler unit is able to give current and voltage measurements with a reduced noise component. It is further used to give the true derivative of currents and voltages in the machine and the power converter, as an average over a PWM period, and as separate values for all states of the power converter. In this way, it can give measurements of the currents as well as the derivative of the currents, at the start and at the end of a single power inverter state. This gave a large degree of freedom in parameter and state identification during uninterrupted operation of the induction machine. The special measurement scheme of the system achieved three main goals: By avoiding the time frame where the transistors commutate and the noise in the measurement of the current is large, filtering of the current measurement is no longer needed. The true derivative of the current in the machine is can be measured with far less noise components. This was extended to give any separate derivative in all three switching states of the power converter. Using the computational resources of the FPGA, more advanced information was supplied to the control system, in order to facilitate sensor less operation, with low computational demands on the DSP. As shown in the papers, this extra information was first used to estimate some of the states of the machine, in some or all of the

  1. Hanford Environmental Dose Reconstruction Project independent direction and oversight

    International Nuclear Information System (INIS)

    Blazek, M.L.; Power, M.

    1991-01-01

    Hanford was selected in 1942 as one of the sites for the Manhattan Project. It produced plutonium for one of the world's first nuclear weapons. The US Department of Energy (DOE) and its predecessors continued to make plutonium for nuclear weapons at Hanford for more than four decades. In the early days of Hanford operations, radioactive materials routinely were released to the environment by many processes. The DOE disclosed documents about these releases in 1986. In 1987, Washington, Oregon, and regional Indian tribes gathered an independent panel of experts. This group recommended dose reconstruction and health effects feasibility studies. Later that year, DOE hired Battelle Pacific Northwest Laboratory (PNL) to reconstruct potential public radiation doses from Hanford's past releases of radioactive material. The DOE agreed with the states and tribes that project direction would come from an independent technical steering panel (TSP). This approach was critical to gain public credibility for the project and the science. The TSP directs the project and makes policy. That is now clear - but, it was hard-earned. Conducting science in an open public process is new, challenging, and clearly worthwhile. The panel's product is good science that is believed and accepted by the public - our client

  2. Parameters used in the environmental pathways and radiological dose modules of the Phase I air pathway code

    International Nuclear Information System (INIS)

    Shindle, S.F.; Ikenberry, T.A.; Napier, B.A.

    1992-05-01

    This report is a description of work performed for the Hanford Environmental Dose Reconstruction (HEDR) Project. The HEDR Project was established to estimate radiation doses to individuals resulting from releases of radionuclides from the Hanford Site since 1944, when facilities there first began operating. An independent Technical Steering Panel directs the project, which is conducted by Battelle staff from the Pacific Northwest Laboratory. The objective of Phase 1 of the HEDR Project was to demonstrate through calculation that adequate models and support data existed or could be developed to allow estimation of realistic doses to individuals from historical Hanford Site radionuclide releases. The HEDR Phase 1 computer code was used to model the transport of iodine-131 released to the atmosphere from the Hanford Site facilities, through environmental pathways to points of human exposure. Output from the code was preliminary estimates of doses received by members of the public living in the vicinity of the Hanford Site. Later project work continues to build upon Phase 1 progress in order to refine dose estimates

  3. Using Patient Health Questionnaire-9 item parameters of a common metric resulted in similar depression scores compared to independent item response theory model reestimation.

    Science.gov (United States)

    Liegl, Gregor; Wahl, Inka; Berghöfer, Anne; Nolte, Sandra; Pieh, Christoph; Rose, Matthias; Fischer, Felix

    2016-03-01

    To investigate the validity of a common depression metric in independent samples. We applied a common metrics approach based on item-response theory for measuring depression to four German-speaking samples that completed the Patient Health Questionnaire (PHQ-9). We compared the PHQ item parameters reported for this common metric to reestimated item parameters that derived from fitting a generalized partial credit model solely to the PHQ-9 items. We calibrated the new model on the same scale as the common metric using two approaches (estimation with shifted prior and Stocking-Lord linking). By fitting a mixed-effects model and using Bland-Altman plots, we investigated the agreement between latent depression scores resulting from the different estimation models. We found different item parameters across samples and estimation methods. Although differences in latent depression scores between different estimation methods were statistically significant, these were clinically irrelevant. Our findings provide evidence that it is possible to estimate latent depression scores by using the item parameters from a common metric instead of reestimating and linking a model. The use of common metric parameters is simple, for example, using a Web application (http://www.common-metrics.org) and offers a long-term perspective to improve the comparability of patient-reported outcome measures. Copyright © 2016 Elsevier Inc. All rights reserved.

  4. Physiological Parameters Database for Older Adults

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Physiological Parameters Database for Older Adults is available for download and contains physiological parameters values for healthy older human adults (age 60...

  5. Surveillance and Control of Malaria Transmission in Thailand using Remotely Sensed Meteorological and Environmental Parameters

    Science.gov (United States)

    Kiang, Richard K.; Adimi, Farida; Soika, Valerii; Nigro, Joseph

    2007-01-01

    These slides address the use of remote sensing in a public health application. Specifically, this discussion focuses on the of remote sensing to detect larval habitats to predict current and future endemicity and identify key factors that sustain or promote transmission of malaria in a targeted geographic area (Thailand). In the Malaria Modeling and Surveillance Project, which is part of the NASA Applied Sciences Public Health Applications Program, we have been developing techniques to enhance public health's decision capability for malaria risk assessments and controls. The main objectives are: 1) identification of the potential breeding sites for major vector species; 2) implementation of a risk algorithm to predict the occurrence of malaria and its transmission intensity; 3) implementation of a dynamic transmission model to identify the key factors that sustain or intensify malaria transmission. The potential benefits are: 1) increased warning time for public health organizations to respond to malaria outbreaks; 2) optimized utilization of pesticide and chemoprophylaxis; 3) reduced likelihood of pesticide and drug resistance; and 4) reduced damage to environment. !> Environmental parameters important to malaria transmission include temperature, relative humidity, precipitation, and vegetation conditions. The NASA Earth science data sets that have been used for malaria surveillance and risk assessment include AVHRR Pathfinder, TRMM, MODIS, NSIPP, and SIESIP. Textural-contextual classifications are used to identify small larval habitats. Neural network methods are used to model malaria cases as a function of the remotely sensed parameters. Hindcastings based on these environmental parameters have shown good agreement to epidemiological records. Discrete event simulations are used for modeling the detailed interactions among the vector life cycle, sporogonic cycle and human infection cycle, under the explicit influences of selected extrinsic and intrinsic factors

  6. Influence of environmental parameters on the concentration of subsurface dissolved methane in two hydroelectric power plants in Brazil

    Science.gov (United States)

    Silva, M. G.; Marani, L.; Alvala, P. C.

    2013-12-01

    Methane (CH4) is a trace gas in the atmosphere of great importance for atmospheric chemistry as one of the main greenhouse gases. There are different sources with the largest individual production associated with the degradation of organic matter submerged in flooded areas. The amount of dissolved methane that reaches the surface depends on the production in the sediments and consumption in the water column. Both processes are associated with microbial activity and consequently dependent on the physico-chemical environmental conditions. The construction of hydroelectric dams cause flooding of areas near the river that can change the characteristics of the environment and cause changes in subsurface methane concentration. In this work, we studied two hydroelectric plants located in Brazil: Batalha (17°20'39.52"S, 47°29'34.29"W), under construction when the samples were take, and Itaipu (25°24'45.00"S, 54°35'39.00"W) which has been floated over 30 years ago. The water samples to determine dissolved methane were collected approximately 5 cm near the surface. In each collection point was measured depth, water temperature, pH and redox potential. The range of dissolved methane between the two dams was similar: 0.07-10.33 μg/l (Batalha) and 0.15-10.93 μg/l (Itaipu). However, the Batalha's average (4.04 × 3.43 μg/l; median = 3.66 μg/l) was higher than that observed in Itaipu (2.15 × 1.59 μg/l; median = 2.53 μg/l). The influence of environmental parameters on the concentration of dissolved methane was evaluated by multivariate statistical techniques (Principal Component Analysis - PCA). All of the parameters had some correlation with dissolved methane, however, the greatest contribution in Batalha was associated with pH while in Itaipu was the depth. The pH variation of the various points studied in Batalha may be associated with periods of drought and flooding of the river and hence the incorporation of organic matter in the environment. The organisms

  7. Effects of environmental and water quality parameters on the functioning of copepod assemblages in tropical estuaries

    Science.gov (United States)

    Araujo, Adriana V.; Dias, Cristina O.; Bonecker, Sérgio L. C.

    2017-07-01

    We examined changes in the functioning of copepod assemblages with increasing pollution in estuaries, using sampling standardization of the salinity range to enable comparisons. Copepod assemblages were analyzed in four southeast Brazilian estuaries with different water quality levels and hydrodynamic characteristics over two years. We obtained mesozooplankton samples together with environmental and water quality parameters in the estuaries, every two months under predetermined salinities ranging from 15 to 25. The values of parameters, except species size, associated with the functioning of the copepod assemblages (biomass, productivity, and turnover rate) did not differ among estuaries. However, in the more polluted estuaries, the biomass and productivity of copepod assemblages of mesozooplankton were negatively correlated with concentration of pollution indicator parameters. Conversely, in the less polluted estuaries some degree of enrichment still seems to increase the system biomass and productivity, as these parameters were inversely related to indicators of improved water quality. The pollution level of estuaries distorted the relationship between temperature and the efficiency of converting energy to organic matter. In the less polluted estuaries, the relationship between turnover rate and temperature was over 70%, while in the most polluted estuaries, this relationship was only approximately 50%. Our results demonstrated that the functioning of assemblages in the estuaries was affected differently by increasing pollution depending on the water quality level of the system. Thus, investigating the functioning of assemblages can be a useful tool for the analysis of estuarine conditions.

  8. Environmental noise and cardiovascular disease in adults: Research in Central, Eastern and South-Eastern Europe and Newly Independent States

    Directory of Open Access Journals (Sweden)

    L′ubica Argalášová-Sobotová

    2013-01-01

    Full Text Available The adverse effects of noise on health have been intensely explored in the past 50 years. However, the scope of research conducted in the Central and Eastern Europe, South-East Europe, and Newly Independent States is not well-known. The aim of this review was to present studies on cardiovascular effects of environmental noise in adults published since 1965 and to point out the most important issues that need to be addressed in the future. More than 100 papers on noise and health and about 20 papers on cardiovascular effects of environmental noise in adults were identified by literature search. The authors reviewed scientific international and local journals, conference proceedings, and local reports published in national languages. The major endpoints were high blood pressure, ischemic heart disease, and myocardial infarction. The target populations were adults. Experimental and exposure-assessment studies, field, empirical studies, social surveys, and epidemiological studies are presented. The major sources of environmental noise were road and air traffic. The results were presented in tables and the most relevant articles were briefly discussed. The importance of this review is that it refers to some countries that no longer exist in the same political and governmental systems. The strength of this paper is that it includes publications that were not evaluated in earlier systematic reviews. Strategies for future noise-related research on national and global level are proposed.

  9. Corporate Governance and Environmental Reporting in Pakistan

    Directory of Open Access Journals (Sweden)

    Muhammad Ali Rafique

    2017-06-01

    Full Text Available The focus of the present study is to investigate the association between environmental reporting and corporate governance traits in Pakistan. The prior studies related to the association between environmental disclosure and corporate governance characteristics show fickle findings. This study fills the gap by using cross sectional data of 100 randomly selected firms registered at Karachi Stock Exchange for the year 2015. The results of the present research showed a positive association between the level of environmental disclosure and fraction of independent directors on the board. Negative relationship was found between environmental disclosure and institutional investors. The result shows a positive association between the level of environmental reporting and board size. It confirms a positive association. The analysis revealed a lack of association between level of environmental reporting and fraction of female directors on a board. In case of control variables, positive relationship was found between firms profitability and level of environmental disclosure, whereas, no correlation was found between firm size and the level of environmental reporting. Moreover, the results of incremental regression indicate that ownership concentration is the most important independent variable among all the independent variables in the model.

  10. The Hanford Environmental Dose Reconstruction Project: Overview

    International Nuclear Information System (INIS)

    Haerer, H.A.; Freshley, M.D.; Gilbert, R.O.; Morgan, L.G.; Napier, B.A.; Rhoads, R.E.; Woodruff, R.K.

    1990-01-01

    In 1988, researchers began a multiyear effort to estimate radiation doses that people could have received since 1944 at the U.S. Department of Energy's Hanford Site. The study was prompted by increasing concern about potential health effects to the public from more than 40 yr of nuclear activities. We will provide an overview of the Hanford Environmental Dose Reconstruction Project and its technical approach. The work has required development of new methods and tools for dealing with unique technical and communication challenges. Scientists are using a probabilistic, rather than the more typical deterministic, approach to generate dose distributions rather than single-point estimates. Uncertainties in input parameters are reflected in dose results. Sensitivity analyses are used to optimize project resources and define the project's scope. An independent technical steering panel directs and approves the work in a public forum. Dose estimates are based on review and analysis of historical data related to operations, effluents, and monitoring; determination of important radionuclides; and reconstruction of source terms, environmental conditions that affected transport, concentrations in environmental media, and human elements, such as population distribution, agricultural practices, food consumption patterns, and lifestyles. A companion paper in this volume, The Hanford Environmental Dose Reconstruction Project: Technical Approach, describes the computational framework for the work

  11. The effect of environmental parameters to dust concentration in air-conditioned space

    Science.gov (United States)

    Ismail, A. M. M.; Manssor, N. A. S.; Nalisa, A.; Yahaya, N.

    2017-08-01

    Malaysia has a wet and hot climate, therefore most of the spaces are air conditioned. The environment might affect dust concentration inside a space and affect the indoor air quality (IAQ). The main objective of this study is to study the dust concentration collected inside enclosed air-conditioned space. The measurement was done physically at four selected offices and two classrooms using a number of equipment to measure the dust concentration and environmental parameters which are temperature and relative air humidity. It was found that the highest dust concentration produced in office (temperature of 24.7°C, relative humidity of 66.5%) is 0.075 mg/m3, as compared to classroom, the highest dust concentration produced is 0.060 mg/m3 office (temperature of 25.9°C, relative humidity of 64.0%). However, both measurements show that value still within the safety level set by DOSH Malaysia (2005-2010) and ASHRAE 62.2 2016. The office contained higher dust concentration compared to classroom because of frequent movement transpires daily due to the functional of the offices.

  12. Assessment of the Eutrophication-Related Environmental Parameters in Two Mediterranean Lakes by Integrating Statistical Techniques and Self-Organizing Maps

    Directory of Open Access Journals (Sweden)

    Ekaterini Hadjisolomou

    2018-03-01

    Full Text Available During the last decades, Mediterranean freshwater ecosystems, especially lakes, have been under severe pressure due to increasing eutrophication and water quality deterioration. In this article, we compared the effectiveness of different data analysis methods by assessing the contribution of environmental parameters to eutrophication processes. For this purpose, principal components analysis (PCA, cluster analysis, and a self-organizing map (SOM were applied, using water quality data from two transboundary lakes of North Greece. SOM is considered as an advanced and powerful data analysis tool because of its ability to represent complex and nonlinear relationships among multivariate data sets. The results of PCA and cluster analysis agreed with the SOM results, although the latter provided more information because of the visualization abilities regarding the parameters’ relationships. Besides nutrients that were found to be a key factor for controlling chlorophyll-a (Chl-a, water temperature was related positively with algal production, while the Secchi disk depth parameter was found to be highly important and negatively related toeutrophic conditions. In general, the SOM results were more specific and allowed direct associations between the water quality variables. Our work showed that SOMs can be used effectively in limnological studies to produce robust and interpretable results, aiding scientists and managers to cope with environmental problems such as eutrophication.

  13. Study of the impact of environmental parameters on the operation of CMS RPCs

    CERN Document Server

    Assran, Yasser

    2011-01-01

    CMS (Compact Muon Solenoid) is a general purpose detector designed to run at the highest luminosity at Large Hadron Collider (LHC), CERN, Geneva, Switzerland. The muon system of the CMS experiment relies on Drift Tubes (DT), Cathode Strip Chambers (CSC) and Resistive Plate Chambers (RPC). RPCs are dedicated for the first level muon trigger and they are characterized by bakelite electrodes delimited in a specialized gas volume filled with operational gas mixture. This analysis has been done for the RPC chambers installed in CMS experiment at CERN. The Currents of CMS RPCs chambers are analyzed as a function of environmental parameters such as Temperature, Humidity and pressure, which are important for the operation of the muon detector system. A novel Neural Network approach has been used to analyze the data and to build a model using experimental measurements and combining the results of the simulations. Data from RPC Chambers in CMS experiment are taken and compared to the results from neural Network.

  14. SPOTting model parameters using a ready-made Python package

    Science.gov (United States)

    Houska, Tobias; Kraft, Philipp; Breuer, Lutz

    2015-04-01

    The selection and parameterization of reliable process descriptions in ecological modelling is driven by several uncertainties. The procedure is highly dependent on various criteria, like the used algorithm, the likelihood function selected and the definition of the prior parameter distributions. A wide variety of tools have been developed in the past decades to optimize parameters. Some of the tools are closed source. Due to this, the choice for a specific parameter estimation method is sometimes more dependent on its availability than the performance. A toolbox with a large set of methods can support users in deciding about the most suitable method. Further, it enables to test and compare different methods. We developed the SPOT (Statistical Parameter Optimization Tool), an open source python package containing a comprehensive set of modules, to analyze and optimize parameters of (environmental) models. SPOT comes along with a selected set of algorithms for parameter optimization and uncertainty analyses (Monte Carlo, MC; Latin Hypercube Sampling, LHS; Maximum Likelihood, MLE; Markov Chain Monte Carlo, MCMC; Scuffled Complex Evolution, SCE-UA; Differential Evolution Markov Chain, DE-MCZ), together with several likelihood functions (Bias, (log-) Nash-Sutcliff model efficiency, Correlation Coefficient, Coefficient of Determination, Covariance, (Decomposed-, Relative-, Root-) Mean Squared Error, Mean Absolute Error, Agreement Index) and prior distributions (Binomial, Chi-Square, Dirichlet, Exponential, Laplace, (log-, multivariate-) Normal, Pareto, Poisson, Cauchy, Uniform, Weibull) to sample from. The model-independent structure makes it suitable to analyze a wide range of applications. We apply all algorithms of the SPOT package in three different case studies. Firstly, we investigate the response of the Rosenbrock function, where the MLE algorithm shows its strengths. Secondly, we study the Griewank function, which has a challenging response surface for

  15. Environmental Education and Sustainability

    Science.gov (United States)

    Chapman, Paul

    2014-01-01

    In the fall of 2013, Inverness Associates conducted a comprehensive national survey of environmental education and sustainability among private independent schools. The National Association of Independent Schools (NAIS) and 14 regional and state associations supported the research. The survey sought to understand how schools' environmental…

  16. Design parameters and source terms: Volume 1, Design parameters: Revision 0

    International Nuclear Information System (INIS)

    1987-09-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report to the level of the Site Characterization Plan - Conceptual Design Report, SCP-CDR. The previous unpublished SCC Study identified the data needs for the Environmental Assessment effort for seven possible salt repository sites

  17. Model-Independent Calculation of Radiative Neutron Capture on Lithium-7

    NARCIS (Netherlands)

    Rupak, Gautam; Higa, Renato

    2011-01-01

    The radiative neutron capture on lithium-7 is calculated model independently using a low-energy halo effective field theory. The cross section is expressed in terms of scattering parameters directly related to the S-matrix elements. It depends on the poorly known p-wave effective range parameter

  18. Integrating GIS and GPS in environmental remediation oversight

    International Nuclear Information System (INIS)

    Kaletsky, K.; Earle, J.R.; Schneider, T.A.

    1996-01-01

    This paper presents findings on Ohio EPA Office of Federal Facilities Oversight's (OFFO) use of GIS and GPS for environmental remediation oversight at the U.S. Department of Energy's (DOE) Fernald Site. The Fernald site is a former uranium metal production facility within DOE's nuclear weapons complex. Significant uranium contamination of soil and groundwater is being remediated under state and federal regulations. OFFO uses GIS/GPS to enhance environmental monitoring and remediation oversight. These technologies are utilized within OFFO's environmental monitoring program for sample location and parameter selection, data interpretation and presentation. GPS is used to integrate sample data into OFFO's GIS and for permanently linking precise and accurate geographic data to samples and waste units. It is important to identify contamination geographically as all visual references (e.g., buildings, infrastructure) will be removed during remediation. Availability of the GIS allows OFFO to perform independent analysis and review of DOE contractor generated data, models, maps, and designs. This ability helps alleviate concerns associated with open-quotes black boxclose quotes models and data interpretation. OFFO's independent analysis has increased regulatory confidence and the efficiency of design reviews. GIS/GPS technology allows OFFO to record and present complex data in a visual format aiding in stakeholder education and awareness. Presented are OFFO's achievements within the aforementioned activities and some reasons learned in implementing the GIS/GPS program. OFFO's two years of GIS/GPS development have resulted in numerous lessons learned and ideas for increasing effectiveness through the use of GIS/GPS

  19. Models and parameters for environmental radiological assessments

    Energy Technology Data Exchange (ETDEWEB)

    Miller, C W [ed.

    1984-01-01

    This book presents a unified compilation of models and parameters appropriate for assessing the impact of radioactive discharges to the environment. Models examined include those developed for the prediction of atmospheric and hydrologic transport and deposition, for terrestrial and aquatic food-chain bioaccumulation, and for internal and external dosimetry. Chapters have been entered separately into the data base. (ACR)

  20. Models and parameters for environmental radiological assessments

    International Nuclear Information System (INIS)

    Miller, C.W.

    1984-01-01

    This book presents a unified compilation of models and parameters appropriate for assessing the impact of radioactive discharges to the environment. Models examined include those developed for the prediction of atmospheric and hydrologic transport and deposition, for terrestrial and aquatic food-chain bioaccumulation, and for internal and external dosimetry. Chapters have been entered separately into the data base

  1. Genetic parameters, phenotypic, genotypic and environmental correlations and genetic variability on sunflower in the Brazilian Savannah

    Directory of Open Access Journals (Sweden)

    Ellen Grippi Lira

    Full Text Available ABSTRACT: Sunflower (Helianthus annuus L. is an annual crop that stands out for its production of high quality oil and for an efficient selection, being necessary to estimate the components of genetic and phenotypic variance. This study aimed to estimate genetic parameters, phenotypic, genotypic and environmental correlations and genetic variability on sunflower in the Brazilian Savannah, evaluating the characters grain yield (YIELD, days to start flowering (DFL based on flowering date in R5, chapter length (CL, weight of a thousand achenes (WTA, plant height (H and oil content (OilC of 16 sunflower genotypes. The experiment was conducted at Embrapa Cerrados, Planaltina, DF, situated at 15º 35’ 30”S latitude, 47º 42’ 30”W longitude and 1.007m above sea level, in soil classified as dystroferric Oxisol. The experimental design used was a complete randomized block with four replicates. The nature for the effects of genotypes and blocks was fixed. Except for the character chapter length, genetic variance was the main component of the phenotypic variance among the genotypes, indicating high genetic variability and experimental efficiency with proper environmental control. In absolute terms, the genetic correlations were superior to phenotypic and environmental. The high values reported for heritability and selective accuracy indicated efficiency of phenotypic selection. Results showed high genetic variability among genotypes, which may contribute to the genetic improvement of sunflower.

  2. [Weight parameters of water quality impact and risk grade determination of water environmental sensitive spots in Jiashan].

    Science.gov (United States)

    Xie, Rong-Rong; Pang, Yong; Zhang, Qian; Chen, Ke; Sun, Ming-Yuan

    2012-07-01

    For the safety of the water environment in Jiashan county in Zhejiang Province, one-dimensional hydrodynamic and water quality models are established based on three large-scale monitoring of hydrology and water quality in Jiashan county, three water environmental sensitive spots including Hongqitang dam Chijia hydrological station and Luxie pond are selected to investigate weight parameters of water quality impact and risk grade determination. Results indicate as follows (1) Internal pollution impact in Jiashan areas was greater than the external, the average weight parameters of internal chemical oxygen demand (COD) pollution is 55.3%, internal ammonia nitrogen (NH(4+)-N) is 67.4%, internal total phosphor (TP) is 63.1%. Non-point pollution impact in Jiashan areas was greater than point pollution impact, the average weight parameters of non-point COD pollutions is 53.7%, non-point NH(4+)-N is 65.9%, non-point TP is 57.8%. (2) The risk of Hongqitang dam and Chijia hydrological station are in the middle risk. The risk of Luxie pond is also in the middle risk in August, and in April and December the risk of Luxie pond is low. The strategic decision will be suggested to guarantee water environment security and social and economic security in the study.

  3. Regulatory standards applicable or relevant to the independent Hanford environmental surveillance and oversight program

    International Nuclear Information System (INIS)

    King, S.E.; Hendrickson, P.L.; Siegel, M.R.; Woodruff, M.G.; Belfiglio, J.; Elliott, R.W.

    1990-03-01

    The authors reviewed federal and state statutes and regulations, as well as Department of Energy (DOE) orders and other guidance material, for potential applicability to the environmental surveillance program conducted for the Hanford site by the Pacific Northwest Laboratory (PNL). There are no federal or state statutes or regulations which are directly applicable to the environmental surveillance program. However, other regulatory schemes, while not directly applicable to the environmental surveillance program, are important insofar as they are indicative of regulatory concern and direction. Because of the evolving nature of environmental regulations, this area needs to be closely monitored for future impact on environmental surveillance activities. 9 refs.,

  4. (C-V) and y-parameters determination of JFETs under different environmental conditions

    Energy Technology Data Exchange (ETDEWEB)

    El-Ghanam, S.M., E-mail: safaaghanam@yahoo.co [Women' s College for Art, Science and Education, Ain-Shams University, Heliopolis, Cairo (Egypt)

    2010-10-01

    The C-V characteristics of n-channel JFET have been measured under different environmental conditions of temperature up to 140 deg. C and {gamma}-rays up to 100 kGy. For low bias voltage and frequency, the input capacitance, C{sub iss}, is shown to be a direct function of temperature. On the other hand, its value was shown to decrease from 11.68 down to 8.17 nF due to {gamma}-exposure up to 100 kGy. The y-parameters of common source amplifier were calculated under the influence of temperature and {gamma}-rays. The results show that the susceptance component of the admittance increases due to increase in temperature, while decreasing after {gamma}-exposure. Considering the cutoff frequency f{sub T0}, it is clear that as the temperature increases from 30 up to 140 deg. C, f{sub T0} dropped from 47 MHz down to 5 MHz, measured at 0.8 V. On the other hand its value was shown to increase from 43 MHz up to 102 MHz, measured at the same bias voltage, due to {gamma}-exposure up to 100 kGy.

  5. Quantifying the ability of environmental parameters to predict soil texture fractions using regression-tree model with GIS and LIDAR data

    DEFF Research Database (Denmark)

    Greve, Mogens Humlekrog; Bou Kheir, Rania; Greve, Mette Balslev

    2012-01-01

    Soil texture is an important soil characteristic that drives crop production and field management, and is the basis for environmental monitoring (including soil quality and sustainability, hydrological and ecological processes, and climate change simulations). The combination of coarse sand, fine...... sand, silt, and clay in soil determines its textural classification. This study used Geographic Information Systems (GIS) and regression-tree modeling to precisely quantify the relationships between the soil texture fractions and different environmental parameters on a national scale, and to detect...... precipitation, seasonal precipitation to statistically explain soil texture fractions field/laboratory measurements (45,224 sampling sites) in the area of interest (Denmark). The developed strongest relationships were associated with clay and silt, variance being equal to 60%, followed by coarse sand (54...

  6. Investigating changes in land use cover and associated environmental parameters in Taihu Lake in recent decades using remote sensing and geochemistry.

    Directory of Open Access Journals (Sweden)

    Changchun Huang

    Full Text Available Humans have had a significant impact on the terrestrial pedosphere through activities such as agriculture and urbanization. The effects of human activities on land use and the related environmental changes were investigated through point and areal studies surrounding Meiliang Bay, which is an open area of extreme eutrophication in Taihu Lake, China. This study used remote sensing and environmental-tracer profiles [total nitrogen (TN, total phosphorus (TP, total organic carbon (TOC, grain size, and geochemical parameters] to determine the causes of changes in land use and the associated environmental parameters. The results of LUCCs (Land use/cover changes indicate that over the past three decades, total farmland decreased by 862.49 km2, with an annual decrement rate of 28.75 km2/year, and total urbanized land increased by 859.71 km2, with an annual growth rate of 28.66 km2/year. The geochemical results indicate that the trophic state of Taihu Lake was persistently intensifying and that the TN, TP, and TOC concentrations increased twofold, threefold, and twofold, respectively, from 1949 to 2010. The sources of TN, TP, and TOC were highly similar after 1975. However, before 1974, TN and TP originated from different sources than TOC. The grassland and woodland around the lake retain nutrients and sand from the land of study area. The increase in urbanized land and tertiary industries significantly increased the sediment concentrations of TN, TP, and TOC after 1980.

  7. On the quantitative relationships between environmental parameters and heavy metals pollution in Mediterranean soils using GIS regression-trees

    DEFF Research Database (Denmark)

    Bou Kheir, Rania; Shomar, B.; Greve, Mogens Humlekrog

    2014-01-01

    Soil heavy metal pollution has been and continues to be a worldwide phenomenon that has attracted a great deal of attention from governments and regulatory bodies. In this context, our study used Geographic Information Systems (GIS) and regression-tree modeling (196 trees) to precisely quantify...... the relationships between four toxic heavy metals (Ni, Cr, Cd and As) and sixteen environmental parameters (e.g., parent material, slope gradient, proximity to roads, etc.) in the soils of northern Lebanon (as a case study of Mediterranean landscapes), and to detect the most important parameters that can be used...... between 68% and 100%), surroundings of waste areas (48 – 92%), proximity to roads (45 – 82%) and parent materials (57 – 73%) considerably influenced all investigated heavy metals, which is not the case of hydromorphological and soil properties. For instance, hydraulic conductivity (18 – 41%) and pH (23...

  8. Environmental parameters influence on the dynamics of total and pathogenic Vibrio parahaemolyticus densities in Crassostrea virginica harvested from Mexico’s Gulf coast

    International Nuclear Information System (INIS)

    López-Hernández, Karla M.; Pardío-Sedas, Violeta T.; Lizárraga-Partida, Leonardo; Williams, José de J.; Martínez-Herrera, David; Flores-Primo, Argel; Uscanga-Serrano, Roxana; Rendón-Castro, Karla

    2015-01-01

    Highlights: • V. parahaemolyticus densities in oysters were isolated in spring and winter seasons. • Pathogenic genes abundances varied with environmental parameters seasonal changes. • Water temperature modulated V. parahaemolyticus abundance during reduced salinities. • V. parahaemolyticus with potentially pathogenic genes raises important health issues. - Abstract: The influence of environmental parameters on the total and pathogenic Vibrio parahaemolyticus seasonal densities in American oysters (Crassostrea virginica) was evaluated for 1 year. Harvesting site A yielded the highest mean densities of V. parahaemolyticus tlh+, tdh+/trh−, tdh−/trh+ and tdh+/trh+ during spring season at 2.57, 1.74, 0.36, and −0.40 log 10 MPN/g, respectively, and tdh+/orf8+ during winter season (0.90 log 10 MPN/g). V. parahaemolyticus tlh+ densities were associated to salinity (R 2 = 0.372, P < 0.022), tdh+/trh+ to turbidity (R 2 = 0.597, P < 0.035), and orf8+ to temperature, salinity, and pH (R 2 = 0.964, P < 0.001). The exposure to salinity and temperature conditions during winter and spring seasons regulated the dynamics of V. parahaemolyticus harboring potentially pathogenic genotypes within the oyster. The adaptive response of V. parahaemolyticus to seasonal environmental changes may lead to an increase in survival and virulence, threatening the seafood safety and increasing the risk of illness

  9. Heritability of audiometric shape parameters and familial aggregation of presbycusis in an elderly Flemish population.

    Science.gov (United States)

    Demeester, Kelly; van Wieringen, Astrid; Hendrickx, Jan-jaap; Topsakal, Vedat; Huyghe, Jeroen; Fransen, Erik; Van Laer, Lut; Van Camp, Guy; Van de Heyning, Paul

    2010-06-14

    This study describes the heritability of audiometric shape parameters and the familial aggregation of different types of presbycusis in a healthy, otologically screened population between 50 and 75 years old. About 342 siblings of 64 families (average family-size: 5.3) were recruited through population registries. Audiometric shape was mathematically quantified by objective parameters developed to measure size, slope, concavity, percentage of frequency-dependent and frequency-independent hearing loss and Bulge Depth. The heritability of each parameter was calculated using a variance components model. Logistic regression models were used to estimate the odds ratios (ORs). Estimates of sibling recurrence risk ratios (lambda(s)) are also provided. Heritability estimates were generally higher compared to previous studies. ORs and lambda(s) for the parameters Total Hearing Loss (size), Uniform Hearing Loss (percentage of frequency-dependent hearing loss) and Bulge Depth suggest a higher heredity for severe types of presbycusis compared to moderate or mild types. Our results suggest that the separation of the parameter 'Total Hearing Loss' into the two parameters 'Uniform Hearing Loss' and 'Non-uniform Hearing Loss' could lead to the discovery of different genetic subtypes of presbycusis. The parameter 'Bulge Depth', instead of 'Concavity', seemed to be an important parameter for classifying subjects into 'susceptible' or 'resistant' to societal or intensive environmental exposure. 2010 Elsevier B.V. All rights reserved.

  10. Nanohydroxyapatite synthesis using optimized process parameters

    Indian Academy of Sciences (India)

    Nanohydroxyapatite; ultrasonication; response surface methodology; calcination; ... Three independent process parameters: temperature () (70, 80 and 90°C), ... Bangi, Selangor, Malaysia; Energy Research Group, School of Engineering, ...

  11. Severe hypoxia affects exercise performance independently of afferent feedback and peripheral fatigue.

    Science.gov (United States)

    Millet, Guillaume Y; Muthalib, Makii; Jubeau, Marc; Laursen, Paul B; Nosaka, Kazunori

    2012-04-01

    To test the hypothesis that hypoxia centrally affects performance independently of afferent feedback and peripheral fatigue, we conducted two experiments under complete vascular occlusion of the exercising muscle under different systemic O(2) environmental conditions. In experiment 1, 12 subjects performed repeated submaximal isometric contractions of the elbow flexor to exhaustion (RCTE) with inspired O(2) fraction fixed at 9% (severe hypoxia, SevHyp), 14% (moderate hypoxia, ModHyp), 21% (normoxia, Norm), or 30% (hyperoxia, Hyper). The number of contractions (performance), muscle (biceps brachii), and prefrontal near-infrared spectroscopy (NIRS) parameters and high-frequency paired-pulse (PS100) evoked responses to electrical muscle stimulation were monitored. In experiment 2, 10 subjects performed another RCTE in SevHyp and Norm conditions in which the number of contractions, biceps brachii electromyography responses to electrical nerve stimulation (M wave), and transcranial magnetic stimulation responses (motor-evoked potentials, MEP, and cortical silent period, CSP) were recorded. Performance during RCTE was significantly reduced by 10-15% in SevHyp (arterial O(2) saturation, SpO(2) = ∼75%) compared with ModHyp (SpO(2) = ∼90%) or Norm/Hyper (SpO(2) > 97%). Performance reduction in SevHyp occurred despite similar 1) metabolic (muscle NIRS parameters) and functional (changes in PS100 and M wave) muscle states and 2) MEP and CSP responses, suggesting comparable corticospinal excitability and spinal and cortical inhibition between SevHyp and Norm. It is concluded that, in SevHyp, performance and central drive can be altered independently of afferent feedback and peripheral fatigue. It is concluded that submaximal performance in SevHyp is partly reduced by a mechanism related directly to brain oxygenation.

  12. PorTL - a compact, portable TLD reader for environmental and personal dosimetry

    International Nuclear Information System (INIS)

    Deme, S.; Apathy, I.; Bodnar, L.; Csoke, A.; Feher, I.; Pazmandi, T.

    2005-01-01

    Thermoluminescent dosimeters (TLDs) are commonly used for environmental monitoring, for personal and medical dosimetry, for dosimetry in nuclear facilities, etc. Major advantages are their independence of the power supply, small dimension, sensitivity, good stability, wide measuring range, resistance to environmental changes and relatively low cost. The disadvantage is that the detector must be transported for evaluation to a laboratory equipped with a large, heavy and expensive TLD Reader operated by qualified personnel, which considerably increases the costs and delays results. To overcome this disadvantage, the KFKI Atomic Energy Research Institute (KFKI AEKI), in co-operation with BL Electronics (Hungary), has developed a new and unique TLD system containing a small, portable, battery powered and moderate-price reader for commercial use. This paper gives a detailed description and parameters of this system.(author)

  13. The non conventional gas, a factor of energy independence?

    International Nuclear Information System (INIS)

    Jacques Percebois

    2011-01-01

    As the recent exploitation of non conventional gases (or shale gases) has dramatically changed the energy deal in the USA, and therefore the energy world market, these gases seem to be a factor of energy independence for countries which possess such resources, but also create environmental constrains. The author describes how shale gas produces a technological revolution, and discusses how it can be a factor for the diversification of the energy mix, and above all a way to reconquer some energy independence

  14. Characterization of diatomite and its application for the retention of radiocobalt: role of environmental parameters

    International Nuclear Information System (INIS)

    Sheng, Guodong; Dong, Huaping; Li, Yimin

    2012-01-01

    Clay minerals have been extensively studied because of their strong sorption and complexation ability. In this work, diatomite was characterized by using acid–base titration. Retention of radionuclide 60 Co(II) from aqueous solution by sorption onto diatomite was investigated by using batch technique under various environmental conditions such as pH, ionic strength, humic acid (HA), fulvic acid (FA), and temperature. The results indicated that the sorption of Co(II) onto diatomite was strongly dependent on pH. At low pH value, the sorption of Co(II) was dominated by outer-sphere surface complexation and ion exchange with Na + /H + on diatomite surfaces, whereas inner-sphere surface complexation was the main sorption mechanism at high pH value. The D–R model fitted the sorption isotherms better than the Langmuir and Freundlich models. The thermodynamic parameters (ΔH 0 , ΔS 0 and ΔG 0 ) calculated from the temperature-dependent sorption isotherms suggested that the sorption of Co(II) was an endothermic and spontaneous process. In addition, diatomite showed higher sorption capacity than that of lots of the sorbents reported in the literatures we surveyed. From the results of Co(II) removal by diatomite, the optimum reaction conditions can be obtained for the maximum removal of Co(II) from water. It is clear that the best pH values of the system to remove Co(II) from solution by using diatomite are 7–8. Considering the low cost and effective disposal of Co(II)-contaminated wastewaters, the best condition for Co(II) removal is at room temperature and solid content of 0.5 g/L. The results might be important for assessing the potential of practical application of diatomite in Co(II) and related radionuclide pollution management. - Highlights: ► The sorption of Co(II) was strongly dependent on ionic strength at low pH, but independent of ionic strength at high pH. ► A positive effect of HA/FA on Co(II) sorption was found at low pH, whereas a negative effect

  15. Independence: proposing an initial framework for occupational therapy.

    Science.gov (United States)

    Collins, Bethan

    2017-11-01

    The concept of independence is common in occupational therapy theory and practice but has rarely been clearly defined or conceptualized within in occupational therapy literature and there seems to be no standard definition. This can result in ambiguity, which potentially jeopardizes client-centred practice. This paper proposes an occupational therapy independence framework (OTIF) that synthesizes the range of characterizations of independence in a practically useful and occupation-centred manner. A review of literature, clinical experience, doctoral research and conversations with occupational therapists and disabled people, in particular those involved in a disability activism group and people with physical disabilities, has led to the development of the OTIF. Independence and interdependence, as characterized in the OTIF, occur when an individual exerts choice over occupational performance and can engage in occupations in a manner acceptable to the individual. Interdependence results when occupations are performed with another person whereas independence involves solitary occupational performance. Dependence typically results from inability to choose occupations or a mismatch between performance capacity and environmental factors. The OTIF has the potential to clarify the conceptualization of independence within occupational therapy theory and practice. This initial proposal is presented to stimulate debate and discussion.

  16. The estimation of soil parameters using observations on crop biophysical variables and the crop model STICS improve the predictions of agro environmental variables.

    Science.gov (United States)

    Varella, H.-V.

    2009-04-01

    Dynamic crop models are very useful to predict the behavior of crops in their environment and are widely used in a lot of agro-environmental work. These models have many parameters and their spatial application require a good knowledge of these parameters, especially of the soil parameters. These parameters can be estimated from soil analysis at different points but this is very costly and requires a lot of experimental work. Nevertheless, observations on crops provided by new techniques like remote sensing or yield monitoring, is a possibility for estimating soil parameters through the inversion of crop models. In this work, the STICS crop model is studied for the wheat and the sugar beet and it includes more than 200 parameters. After a previous work based on a large experimental database for calibrate parameters related to the characteristics of the crop, a global sensitivity analysis of the observed variables (leaf area index LAI and absorbed nitrogen QN provided by remote sensing data, and yield at harvest provided by yield monitoring) to the soil parameters is made, in order to determine which of them have to be estimated. This study was made in different climatic and agronomic conditions and it reveals that 7 soil parameters (4 related to the water and 3 related to the nitrogen) have a clearly influence on the variance of the observed variables and have to be therefore estimated. For estimating these 7 soil parameters, a Bayesian data assimilation method is chosen (because of available prior information on these parameters) named Importance Sampling by using observations, on wheat and sugar beet crop, of LAI and QN at various dates and yield at harvest acquired on different climatic and agronomic conditions. The quality of parameter estimation is then determined by comparing the result of parameter estimation with only prior information and the result with the posterior information provided by the Bayesian data assimilation method. The result of the

  17. Morphology parameters for intracranial aneurysm rupture risk assessment.

    Science.gov (United States)

    Dhar, Sujan; Tremmel, Markus; Mocco, J; Kim, Minsuok; Yamamoto, Junichi; Siddiqui, Adnan H; Hopkins, L Nelson; Meng, Hui

    2008-08-01

    The aim of this study is to identify image-based morphological parameters that correlate with human intracranial aneurysm (IA) rupture. For 45 patients with terminal or sidewall saccular IAs (25 unruptured, 20 ruptured), three-dimensional geometries were evaluated for a range of morphological parameters. In addition to five previously studied parameters (aspect ratio, aneurysm size, ellipticity index, nonsphericity index, and undulation index), we defined three novel parameters incorporating the parent vessel geometry (vessel angle, aneurysm [inclination] angle, and [aneurysm-to-vessel] size ratio) and explored their correlation with aneurysm rupture. Parameters were analyzed with a two-tailed independent Student's t test for significance; significant parameters (P 41; 95% confidence interval, 1.03-1.92) and undulation index (odds ratio, 1.51; 95% confidence interval, 1.08-2.11) had the strongest independent correlation with ruptured IA. From the receiver operating characteristic analysis, size ratio and aneurysm angle had the highest area under the curve values of 0.83 and 0.85, respectively. Size ratio and aneurysm angle are promising new morphological metrics for IA rupture risk assessment. Because these parameters account for vessel geometry, they may bridge the gap between morphological studies and more qualitative location-based studies.

  18. Essays on environmental management

    OpenAIRE

    Marbuah, George

    2016-01-01

    This thesis contributes to the economic literature on invasive species, social capital connection to climate change and environmental good provision as well as energy demand management. It contains five independent papers connected by the broader theme of environmental management. Two papers (I and II) deal with invasive species while the third and fourth probes the effect of social capital on carbon dioxide emissions (CO₂) and individuals’ decision to contribute toward environmental protecti...

  19. Appraising the value of independent EIA follow-up verifiers

    Energy Technology Data Exchange (ETDEWEB)

    Wessels, Jan-Albert, E-mail: janalbert.wessels@nwu.ac.za [School of Geo and Spatial Sciences, Department of Geography and Environmental Management, North-West University, C/O Hoffman and Borcherd Street, Potchefstroom, 2520 (South Africa); Retief, Francois, E-mail: francois.retief@nwu.ac.za [School of Geo and Spatial Sciences, Department of Geography and Environmental Management, North-West University, C/O Hoffman and Borcherd Street, Potchefstroom, 2520 (South Africa); Morrison-Saunders, Angus, E-mail: A.Morrison-Saunders@murdoch.edu.au [School of Geo and Spatial Sciences, Department of Geography and Environmental Management, North-West University, C/O Hoffman and Borcherd Street, Potchefstroom, 2520 (South Africa); Environmental Assessment, School of Environmental Science, Murdoch University, Australia. (Australia)

    2015-01-15

    Independent Environmental Impact Assessment (EIA) follow-up verifiers such as monitoring agencies, checkers, supervisors and control officers are active on various construction sites across the world. There are, however, differing views on the value that these verifiers add and very limited learning in EIA has been drawn from independent verifiers. This paper aims to appraise how and to what extent independent EIA follow-up verifiers add value in major construction projects in the developing country context of South Africa. A framework for appraising the role of independent verifiers was established and four South African case studies were examined through a mixture of site visits, project document analysis, and interviews. Appraisal results were documented in the performance areas of: planning, doing, checking, acting, public participating and integration with other programs. The results indicate that independent verifiers add most value to major construction projects when involved with screening EIA requirements of new projects, allocation of financial and human resources, checking legal compliance, influencing implementation, reporting conformance results, community and stakeholder engagement, integration with self-responsibility programs such as environmental management systems (EMS), and controlling records. It was apparent that verifiers could be more creatively utilized in pre-construction preparation, providing feedback of knowledge into assessment of new projects, giving input to the planning and design phase of projects, and performance evaluation. The study confirms the benefits of proponent and regulator follow-up, specifically in having independent verifiers that disclose information, facilitate discussion among stakeholders, are adaptable and proactive, aid in the integration of EIA with other programs, and instill trust in EIA enforcement by conformance evaluation. Overall, the study provides insight on how to harness the learning opportunities

  20. Appraising the value of independent EIA follow-up verifiers

    International Nuclear Information System (INIS)

    Wessels, Jan-Albert; Retief, Francois; Morrison-Saunders, Angus

    2015-01-01

    Independent Environmental Impact Assessment (EIA) follow-up verifiers such as monitoring agencies, checkers, supervisors and control officers are active on various construction sites across the world. There are, however, differing views on the value that these verifiers add and very limited learning in EIA has been drawn from independent verifiers. This paper aims to appraise how and to what extent independent EIA follow-up verifiers add value in major construction projects in the developing country context of South Africa. A framework for appraising the role of independent verifiers was established and four South African case studies were examined through a mixture of site visits, project document analysis, and interviews. Appraisal results were documented in the performance areas of: planning, doing, checking, acting, public participating and integration with other programs. The results indicate that independent verifiers add most value to major construction projects when involved with screening EIA requirements of new projects, allocation of financial and human resources, checking legal compliance, influencing implementation, reporting conformance results, community and stakeholder engagement, integration with self-responsibility programs such as environmental management systems (EMS), and controlling records. It was apparent that verifiers could be more creatively utilized in pre-construction preparation, providing feedback of knowledge into assessment of new projects, giving input to the planning and design phase of projects, and performance evaluation. The study confirms the benefits of proponent and regulator follow-up, specifically in having independent verifiers that disclose information, facilitate discussion among stakeholders, are adaptable and proactive, aid in the integration of EIA with other programs, and instill trust in EIA enforcement by conformance evaluation. Overall, the study provides insight on how to harness the learning opportunities

  1. Parameter Optimization for Feature and Hit Generation in a General Unknown Screening Method-Proof of Concept Study Using a Design of Experiment Approach for a High Resolution Mass Spectrometry Procedure after Data Independent Acquisition.

    Science.gov (United States)

    Elmiger, Marco P; Poetzsch, Michael; Steuer, Andrea E; Kraemer, Thomas

    2018-03-06

    High resolution mass spectrometry and modern data independent acquisition (DIA) methods enable the creation of general unknown screening (GUS) procedures. However, even when DIA is used, its potential is far from being exploited, because often, the untargeted acquisition is followed by a targeted search. Applying an actual GUS (including untargeted screening) produces an immense amount of data that must be dealt with. An optimization of the parameters regulating the feature detection and hit generation algorithms of the data processing software could significantly reduce the amount of unnecessary data and thereby the workload. Design of experiment (DoE) approaches allow a simultaneous optimization of multiple parameters. In a first step, parameters are evaluated (crucial or noncrucial). Second, crucial parameters are optimized. The aim in this study was to reduce the number of hits, without missing analytes. The obtained parameter settings from the optimization were compared to the standard settings by analyzing a test set of blood samples spiked with 22 relevant analytes as well as 62 authentic forensic cases. The optimization lead to a marked reduction of workload (12.3 to 1.1% and 3.8 to 1.1% hits for the test set and the authentic cases, respectively) while simultaneously increasing the identification rate (68.2 to 86.4% and 68.8 to 88.1%, respectively). This proof of concept study emphasizes the great potential of DoE approaches to master the data overload resulting from modern data independent acquisition methods used for general unknown screening procedures by optimizing software parameters.

  2. Independent Technical (open-quotes Red Teamclose quotes) Reviews

    International Nuclear Information System (INIS)

    Thullen, P.; Bennett, D.R.; Kosiewicz, S.T.; Weaver, D.L.

    1995-01-01

    Offices under the Assistant Secretary for Environmental Restoration and Waste Management (EM) in the Department of Energy (DOE) and some National Laboratories are using Independent Technical or open-quotes Red Teamclose quotes Reviews to understand and improve the performance of major projects, major system acquisitions, programs and organizations. A core group formed in 1991 by Los Alamos National Laboratory and Sandia National Laboratories, has organized teams of commercial and private consultants to perform over fifteen Independent Technical Reviews (ITRs) throughout the DOE Complex. This paper discusses: review initiation, team formation, methodology, site response, and observations gathered over the past three years

  3. A DTI-based model for TMS using the independent impedance method with frequency-dependent tissue parameters

    Science.gov (United States)

    De Geeter, N.; Crevecoeur, G.; Dupré, L.; Van Hecke, W.; Leemans, A.

    2012-04-01

    Accurate simulations on detailed realistic head models are necessary to gain a better understanding of the response to transcranial magnetic stimulation (TMS). Hitherto, head models with simplified geometries and constant isotropic material properties are often used, whereas some biological tissues have anisotropic characteristics which vary naturally with frequency. Moreover, most computational methods do not take the tissue permittivity into account. Therefore, we calculate the electromagnetic behaviour due to TMS in a head model with realistic geometry and where realistic dispersive anisotropic tissue properties are incorporated, based on T1-weighted and diffusion-weighted magnetic resonance images. This paper studies the impact of tissue anisotropy, permittivity and frequency dependence, using the anisotropic independent impedance method. The results show that anisotropy yields differences up to 32% and 19% of the maximum induced currents and electric field, respectively. Neglecting the permittivity values leads to a decrease of about 72% and 24% of the maximum currents and field, respectively. Implementing the dispersive effects of biological tissues results in a difference of 6% of the maximum currents. The cerebral voxels show limited sensitivity of the induced electric field to changes in conductivity and permittivity, whereas the field varies approximately linearly with frequency. These findings illustrate the importance of including each of the above parameters in the model and confirm the need for accuracy in the applied patient-specific method, which can be used in computer-assisted TMS.

  4. State environmental review of a proposed utility independent spent fuel storage installation

    International Nuclear Information System (INIS)

    Sabel, G.; Halstead, R.

    1991-01-01

    This paper describes the environmental review process which was applied by the State of Minnesota to a proposed dry cask storage facility. An environmental analysis of the proposed project is summarized, as are alternatives including other dry storage technologies, increased in-pool storage, transhipment, reprocessing, use of higher burnup fuel and conservation. Public comments and concerns included potential cask failures, health impacts, and the possibility of the site becoming a open-quotes permanentclose quotes storage facility. State intervention in the federal license process is also described

  5. Use of environmental parameters to explain the variability in ...

    African Journals Online (AJOL)

    Abstract. This study attempts to explain the variability in recruitment of sardine in the northern Benguela and to develop potential models by including environmental information to predict recruitment. ... AJOL African Journals Online. HOW TO ...

  6. Environmental implications of offshore oil and gas development in Australia. The finding of an independent scientific review

    International Nuclear Information System (INIS)

    Swan, J.M.; Neff, J.M.; Young, P.C.

    1994-01-01

    It is widely recognised that uncontrolled discharge of petroleum products or other materials from offshore oil and gas exploration and production wells, and from associated industrial operations including treatment and service facilities that are required to be on or near the coast, can have direct and sometimes deleterious impacts on the marine environment. In mid-1992, the Australian Petroleum Exploration Association (APEA) commissioned five scientific reviews to examine the environmental implications of offshore petroleum developments in Australia. The reviews, carried out by an Independent Scientific Review Committee on behalf of the Australian Petroleum Exploration Association (APEA) and the Energy Research and Development Corporation (ERDC) deal with: (1) the preliminary geophysical exploration of the sea bed and underlying strata using seismic surveys, and especially the effects of bursts of underwater sound energy on biological communities; (2) the drilling of offshore wells, especially the disposal of drilling fluids and drill cuttings; (3) the production of oil and gas from proven wells, especially the disposal of large quantities of produced formation water (fossil water); (4) the construction and operation of coastal support facilities and associated activities which might have consequences for marine habitats; (5) oil spills associated with any of the above operations and especially the likely short- and long-term effects of an accidental oil spill on marine biota and on the aesthetic and commercial values of an impacted coastline. Comments on the findings are preceded by a brief summary of background information, relevant technologies and the main implications for the marine environment. Some suggestions are provided for possible future research, monitoring and environmental management. refs., figs., tabs

  7. Co-variation of Cholera with Climatic and Environmental Parameters ...

    African Journals Online (AJOL)

    adjusted cholera cases and coastal ocean chlorophyll a and, to some degree, sea surface temperature, the ... environmental variables, such as air and water temperature, rainfall ... nutrients and plankton biomass (Vezulli et al., 2010). Water ...

  8. Study of environmental pollution by heavy metals in Sepetiba Bay and Paraiba do Sul River - Guandu River by analysis of critical parameters

    International Nuclear Information System (INIS)

    Pfeiffer, W.C.; Fiszman, M.; Malm, O.; Lima, N.R.W.; Azcue, J.M.

    The heavy metal pollution in Sepetiba Bay and Paraiba do Sul River - Guandu River is studied by analysis of critical parameters. This ones are employed in environmental impact determination of nuclear installations. Three critic metals (Cr, Zn, Cd) and four (Pb, Cu, Zn, Cr) ones are lauched by the industrial park of Sepetiba Bay and Paraiba Vale respectively. (M.A.C.) [pt

  9. Are Independent Probes Truly Independent?

    Science.gov (United States)

    Camp, Gino; Pecher, Diane; Schmidt, Henk G.; Zeelenberg, Rene

    2009-01-01

    The independent cue technique has been developed to test traditional interference theories against inhibition theories of forgetting. In the present study, the authors tested the critical criterion for the independence of independent cues: Studied cues not presented during test (and unrelated to test cues) should not contribute to the retrieval…

  10. Influence of sulphate-reducing bacteria on environmental parameters and marine corrosion behavior of Q235 steel in aerobic conditions

    International Nuclear Information System (INIS)

    Wan Yi; Zhang Dun; Liu Huaiqun; Li Yongjuan; Hou Baorong

    2010-01-01

    The growth cycle of sulphate-reducing bacteria (SRB), Desulfovibrio caledoniensis, and the effect of SRB on the environmental parameters and corrosion behavior of Q235 steel during a growth cycle in aerobic (air- and O 2 -saturated culture solutions) and anaerobic (N 2 - saturated culture solutions) conditions were investigated. Oxygen dissolved in the culture solutions induced slow growth and fast decay of SRB. The growth process of SRB under anaerobic and aerobic conditions influenced sulphide anion concentration (C s 2- ), pH, and conductivity (κ). The values of C s 2- and κ under aerobic conditions were lower than those under anaerobic conditions, and the pH values increased from O 2 - to air- to N 2 -saturated culture solutions. Aerobic conditions induced the open circuit potential (E OC ) to shift in the positive direction after the stationary phase of SRB growth. The charge transfer resistance (R ct ) increased quickly during the exponential growth phase, almost maintained stability during the stationary phase, and decreased after the stationary phase in all three conditions, and the impedance magnitude decreased from O 2 - to air- to N 2 -saturated culture solutions. The biofilms induced by SRB were observed by scanning electron microscopy (SEM) under aerobic and anaerobic conditions, and energy dispersive spectroscopy (EDS) was performed in abiotic and SRB-containing systems to distinguish the corrosion products. The reasons for the effects of SRB on the environmental parameters and corrosion behavior of carbon steel are discussed.

  11. Foraging behavior, environmental parameters and nests development of Melipona colimana Ayala (Hymenoptera: Meliponini) in temperate climate of Jalisco, México.

    Science.gov (United States)

    Macías-Macías, J O; Tapia-Gonzalez, J M; Contreras-Escareño, F

    2017-01-01

    Melipona colimana Ayala is an endemic species inhabiting temperate forests of pine and oak of south of Jalisco in Mexico. During a year, it was recorded every 15 days foraging activity, environmental parameters and the development of colonies of M. colimana in its wild habitat. For five minutes every hour from 7:00 to 21:00, the bees that entered and left the hive and bringing pollen and resin were registered. Every hour the relative humidity, temperature, wind speed and light intensity was recorded and related to foraging activity. Additionally, the weight of the colonies recently transferred to wooden boxes, the number of brood combs, honey pots and pollen were registered. The time of beginning and ending of the foraging activity differs from the reports of stingless bees of tropical weather and the same happens with the pollen collection. The environmental parameters that affect other tropical stingless bees in the foraging activity also affect M. colimana in temperate climate. It was determined that the major activity season and the presence of more pollen pots in the colony is from November through February, for what it could be the best time of the year for the division and obtainance of new colonies, while the critical period of minor activity and pollen flow was during rainy season. These data may be useful for the future sustainable use of this species in temperate climate.

  12. Hanford Environmental Dose Reconstruction Project

    International Nuclear Information System (INIS)

    Cannon, S.D.; Finch, S.M.

    1992-10-01

    The objective of the Hanford Environmental Dose Reconstruction (HEDR) Project is to estimate the radiation doses that individuals and populations could have received from nuclear operations at Hanford since 1944. The independent Technical Steering Panel (TSP) provides technical direction. The project is divided into the following technical tasks. These tasks correspond to the path radionuclides followed from release to impact on humans (dose estimates):Source Terms, Environmental Transport, Environmental Monitoring Data, Demography, Food Consumption, and Agriculture, and Environmental Pathways and Dose Estimates

  13. Tricks of the trade: Sharing ideas about independent hydro development in Canada

    International Nuclear Information System (INIS)

    Collins, S.J.

    1992-01-01

    Preparation and patience are the keys to developing independent hydropower projects in Canada. Several individuals who have experience breaking into the business share their advice. Opportunities for independent hydro developers to contribute to electricity production in Canada are increasing, thanks to government and utility support. Site selection, costs, environmental regulations, native rights issues, project approval processes, and time lines are all important issues

  14. Generalised analysis of the potential of an enterprise as a function of environmental parameters (theoretical approach

    Directory of Open Access Journals (Sweden)

    Karapeychik Igor M.

    2013-03-01

    Full Text Available Within the frameworks of the author’s concept of the potential of an enterprise as the ability to conduct its immanently appropriate activity and also the idea of presentation of the size of the potential in the form of potential function from parameters of the state of an enterprise and foreign economic environment the article develops a scientific and methodical approach to construction and analysis of the potential function of an enterprise. The offered approach envisages building an economic and mathematical model of an enterprise of the optimisation type with consideration of environmental factors, determination of the size of economic potential as a maximum possible (optimal with the set condition of an enterprise and external environment of net income, statistical test of the model with possible values of external parameters (formation of statistical sampling of the graph of the potential function of an enterprise and application of statistical methods including methods of correlation, factor and regression analysis, for the study of its properties. Operability of this approach is shown on the example of the study of properties of the potential function of a model enterprise. In the course of approbation the article demonstrates its ability to reveal specific features of impact of external factors on economic potential of an enterprise; establishes, as a common regularity, differential influence of various environmental factors, caused not only by the nature of these factors, but also production and economic specific features and specific state of an enterprise. The article shows that the quantitative values of the force of influence of the said factors upon the value of economic potential, obtained during statistical analysis of the potential function of an enterprise, could serve as an instrument of ranking these factors by the priority level in the goal setting tasks at the stage of formation of the strategy of enterprise development

  15. Evaluating the environmental fate of pharmaceuticals using a level III model based on poly-parameter linear free energy relationships

    International Nuclear Information System (INIS)

    Zukowska, Barbara; Breivik, Knut; Wania, Frank

    2006-01-01

    We recently proposed how to expand the applicability of multimedia models towards polar organic chemicals by expressing environmental phase partitioning with the help of poly-parameter linear free energy relationships (PP-LFERs). Here we elaborate on this approach by applying it to three pharmaceutical substances. A PP-LFER-based version of a Level III fugacity model calculates overall persistence, concentrations and intermedia fluxes of polar and non-polar organic chemicals between air, water, soil and sediments at steady-state. Illustrative modeling results for the pharmaceuticals within a defined coastal region are presented and discussed. The model results are highly sensitive to the degradation rate in water and the equilibrium partitioning between organic carbon and water, suggesting that an accurate description of this particular partitioning equilibrium is essential in order to obtain reliable predictions of environmental fate. The PP-LFER based modeling approach furthermore illustrates that the greatest mobility in aqueous phases may be experienced by pharmaceuticals that combines a small molecular size with strong H-acceptor properties

  16. Evaluating the environmental fate of pharmaceuticals using a level III model based on poly-parameter linear free energy relationships

    Energy Technology Data Exchange (ETDEWEB)

    Zukowska, Barbara [Department of Analytical Chemistry, Chemical Faculty, Gdansk University of Technology, 11/12 G. Narutowicza St., 80-952 Gdansk (Poland); Breivik, Knut [NILU- Norwegian Institute for Air Research, P.O. Box 100, NO-2027 Kjeller (Norway)]. E-mail: knut.breivik@nilu.no; Wania, Frank [Department of Physical and Environmental Sciences, University of Toronto at Scarborough, 1265 Military Trail, Scarborough, Ontario, M1C 1A4 (Canada)

    2006-04-15

    We recently proposed how to expand the applicability of multimedia models towards polar organic chemicals by expressing environmental phase partitioning with the help of poly-parameter linear free energy relationships (PP-LFERs). Here we elaborate on this approach by applying it to three pharmaceutical substances. A PP-LFER-based version of a Level III fugacity model calculates overall persistence, concentrations and intermedia fluxes of polar and non-polar organic chemicals between air, water, soil and sediments at steady-state. Illustrative modeling results for the pharmaceuticals within a defined coastal region are presented and discussed. The model results are highly sensitive to the degradation rate in water and the equilibrium partitioning between organic carbon and water, suggesting that an accurate description of this particular partitioning equilibrium is essential in order to obtain reliable predictions of environmental fate. The PP-LFER based modeling approach furthermore illustrates that the greatest mobility in aqueous phases may be experienced by pharmaceuticals that combines a small molecular size with strong H-acceptor properties.

  17. Determinant of The Corporate Environmental Disclosure: Study on Jakarta Islamic Index

    Directory of Open Access Journals (Sweden)

    Yulianti Yulianti

    2016-07-01

    Full Text Available The issue about corporate environment disclosure nowadays is increasing. This research aims to analyze the influence of firm size, leverage, proportion of independent commissioners, corporate secretary and firm age to corporate environmental disclosure. Thirteen companies that listed at Jakarta Islamic Index during 2011-2014 are used as sample. Data was analyzed using multiple regression technique. The independent variables are firm size, leverage, and proportions of independent commissioners, corporate secretary, and firma age. The result shows that simultaneously all independent variables have significant influence to corporate environmental disclosure. Whereas partially, firm size and firm age have significantly influence to corporate environmental disclosure. The implication of this research is the larger of the firm size and the longer firm will make a better corporate environmental disclosure in companies that listed at Jakarta Islamic Index.DOI: 10.15408/aiq.v8i2.3158

  18. Precision cosmological measurements: Independent evidence for dark energy

    International Nuclear Information System (INIS)

    Bothun, Greg; Hsu, Stephen D.H.; Murray, Brian

    2008-01-01

    Using recent precision measurements of cosmological parameters, we re-examine whether these observations alone, independent of type Ia supernova surveys, are sufficient to imply the existence of dark energy. We find that best measurements of the age of the Universe t 0 , the Hubble parameter H 0 and the matter fraction Ω m strongly favor an equation of state defined by (w<-1/3). This result is consistent with the existence of a repulsive, acceleration-causing component of energy if the Universe is nearly flat

  19. Environmental isotope balance of Lake Kinneret as a tool in evaporation rate estimation

    International Nuclear Information System (INIS)

    Lewis, S.

    1979-01-01

    The balance of environmental isotopes in Lake Kinneret has been used to obtain an independent estimate of the mean monthly evaporation rate. Direct calculation was precluded by the inadequacy of the isotope data in uniquely representing the system behaviour throughout the annual cycle. The approach adopted uses an automatic algorithm to seek an objective best fit of the isotope balance model to measured oxygen-18 data by optimizing the evaporation rate as a parameter. To this end, evaporation is described as a periodic function with two parameters. The sensitivity of the evaporation rate estimates to parameter uncertainty and data errors is stressed. Error analysis puts confidence limits on the estimates obtained. Projected improvements in data collection and analysis show that a significant reduction in uncertainty can be realized. Relative to energy balance estimates, currently obtainable data result in about 30% uncertainty. The most optimistic scenario would yield about 15% relative uncertainty. (author)

  20. Firms’ Board Independence and Corporate Social Performance: A Meta-Analysis

    Directory of Open Access Journals (Sweden)

    Eduardo Ortas

    2017-06-01

    Full Text Available This paper investigates the influence of organizations’ board independence on corporate social performance (CSP using a meta-analytic approach. A sample of 87 published papers is used to identify a set of underlying moderating effects in that relationship. Specifically, differences in the system of corporate governance, CSP measurement models and market conditions have been considered as moderating variables. The results show that the independence of a company’s board positively influences CSP. This is because companies with more independent directors in their boards are more likely to commit to stakeholder engagement, environmental preservation and community well-being. Interestingly, the results also show that the positive connection between board independence and CSP is stronger in civil law countries and when CSP is measured by self-reporting data. Finally, the strength of the influence of the independence of a firm’s board on CSP varies significantly in different market conditions. The paper concludes by presenting the main implications for academics, practitioners and policy makers.

  1. Final environmental impact statement for the construction and operation of an independent spent fuel storage installation to store the Three Mile Island Unit 2 spent fuel at the Idaho National Engineering and Environmental Laboratory. Docket Number 72-20

    International Nuclear Information System (INIS)

    1998-03-01

    This Final Environmental Impact Statement (FEIS) contains an assessment of the potential environmental impacts of the construction and operation of an Independent Spent Fuel Storage Installation (ISFSI) for the Three Mile Island Unit 2 (TMI-2) fuel debris at the Idaho National Engineering and Environmental laboratory (INEEL). US Department of Energy-Idaho Operations Office (DOE-ID) is proposing to design, construct, and operate at the Idaho Chemical Processing Plant (ICPP). The TMI-2 fuel debris would be removed from wet storage, transported to the ISFSI, and placed in storage modules on a concrete basemat. As part of its overall spent nuclear fuel (SNF) management program, the US DOE has prepared a final programmatic environmental impact statement (EIS) that provides an overview of the spent fuel management proposed for INEEL, including the construction and operation of the TMI-2 ISFSI. In addition, DOE-ID has prepared an environmental assessment (EA) to describe the environmental impacts associated with the stabilization of the storage pool and the construction/operation of the ISFSI at the ICPP. As provided in NRC's NEPA procedures, a FEIS of another Federal agency may be adopted in whole or in part in accordance with the procedures outlined in 40 CFR 1506.3 of the regulations of the Council on Environmental Quality (CEQ). Under 40 CFR 1506.3(b), if the actions covered by the original EIS and the proposed action are substantially the same, the agency adopting another agency's statement is not required to recirculate it except as a final statement. The NRC has determined that its proposed action is substantially the same as actions considered in DOE's environmental documents referenced above and, therefore, has elected to adopt the DOE documents as the NRC FEIS

  2. Massively Parallel Dimension Independent Adaptive Metropolis

    KAUST Repository

    Chen, Yuxin

    2015-05-14

    This work considers black-box Bayesian inference over high-dimensional parameter spaces. The well-known and widely respected adaptive Metropolis (AM) algorithm is extended herein to asymptotically scale uniformly with respect to the underlying parameter dimension, by respecting the variance, for Gaussian targets. The result- ing algorithm, referred to as the dimension-independent adaptive Metropolis (DIAM) algorithm, also shows improved performance with respect to adaptive Metropolis on non-Gaussian targets. This algorithm is further improved, and the possibility of probing high-dimensional targets is enabled, via GPU-accelerated numerical libraries and periodically synchronized concurrent chains (justified a posteriori). Asymptoti- cally in dimension, this massively parallel dimension-independent adaptive Metropolis (MPDIAM) GPU implementation exhibits a factor of four improvement versus the CPU-based Intel MKL version alone, which is itself already a factor of three improve- ment versus the serial version. The scaling to multiple CPUs and GPUs exhibits a form of strong scaling in terms of the time necessary to reach a certain convergence criterion, through a combination of longer time per sample batch (weak scaling) and yet fewer necessary samples to convergence. This is illustrated by e ciently sampling from several Gaussian and non-Gaussian targets for dimension d 1000.

  3. Hanford Environmental Dose Reconstruction Project

    International Nuclear Information System (INIS)

    Finch, S.M.; McMakin, A.H.

    1991-04-01

    The objective of the Hanford Environmental Dose Reconstruction Project is to estimate the radiation doses that populations could have received from nuclear operations at Hanford since 1944. The project is being managed and conducted by the Pacific Northwest Laboratory (PNL) under the direction of an independent Technical Steering Panel (TSP). The project is divided into the following technical tasks. These tasks correspond to the path radionuclides followed, from released to impact on humans (dose estimates): source terms; environmental transport; environmental monitoring data; demographics, agriculture, food habits; and, environmental pathways and dose estimates

  4. Integrated approach to the understanding of the degradation of an urban river: local perceptions, environmental parameters and geoprocessing.

    Science.gov (United States)

    Collier, Carolina A; Almeida Neto, Miguel S de; Aretakis, Gabriela M A; Santos, Rangel E; de Oliveira, Tiago H; Mourão, José S; Severi, William; El-Deir, Ana C A

    2015-09-15

    The use of interdisciplinary approaches such as the proposed report provides a broad understanding of the relationship between people and the environment, revealing reliable aspects not previously considered in the study of this relationship. This study compiled evidence on the environmental degradation of an urbanized river over the past few decades, providing a diagnosis of the consequences of this process for the river, its ichthyofauna, and the local human population. The study was focused on the Beira Rio community on the Capibaribe River in the municipality of São Lourenço da Mata, Pernambuco, Brazil. Data were collected using geoprocessing and ethnobiological approaches, as well as environmental parameters. This research was conducted with the most experienced long-term residents in the local community, through interviews and participatory methodologies to recovering information about the river environment, its ichthyofauna and its environmental services for the last decades. According to the GIS analysis, the study area was subject to an accelerated process of urbanization, with the total urban area increasing from 73 565, 98 m(2) in 1974 to 383 363, 6 m(2) in 2005. The informants perceived the urban growth, especially in the late twentieth century, being this period recognized as the phase of greatest negative changes in the river environment. The perceived decline of fish stocks was indicated by the community as one of the effects of river degradation. According to the interviews, the deterioration of the river affected the ecosystem services and the relationship of the adjacent human community with this ecosystem. The environmental data indicated that the river is suffering eutrophization and has fecal coliform concentrations 160 times higher than the maximum level permitted by Brazilian legislation. The interdisciplinary approach used in this research allowed the understanding of the degradation process of an urban river and some negative effects

  5. Environmental pollution studies

    CERN Document Server

    Best, Gerry

    1999-01-01

    This book examines a number of important contemporary environmental issues in an informative and easy-to-read style. The topics covered include sewage treatment, eutrophication, air pollution, acid rain, global warming and pollution from farming. A particularly valuable section of the book describes a range of tests that can be carried out on various environmental parameters. The procedures require relatively simple equipment and they have been pre-tested in a school laboratory. "Environmental Pollution Studies" will be of value to senior school pupils and students at college or university embarking on courses in environmental science.

  6. RNA-Sequencing Reveals Unique Transcriptional Signatures of Running and Running-Independent Environmental Enrichment in the Adult Mouse Dentate Gyrus.

    Science.gov (United States)

    Grégoire, Catherine-Alexandra; Tobin, Stephanie; Goldenstein, Brianna L; Samarut, Éric; Leclerc, Andréanne; Aumont, Anne; Drapeau, Pierre; Fulton, Stephanie; Fernandes, Karl J L

    2018-01-01

    Environmental enrichment (EE) is a powerful stimulus of brain plasticity and is among the most accessible treatment options for brain disease. In rodents, EE is modeled using multi-factorial environments that include running, social interactions, and/or complex surroundings. Here, we show that running and running-independent EE differentially affect the hippocampal dentate gyrus (DG), a brain region critical for learning and memory. Outbred male CD1 mice housed individually with a voluntary running disk showed improved spatial memory in the radial arm maze compared to individually- or socially-housed mice with a locked disk. We therefore used RNA sequencing to perform an unbiased interrogation of DG gene expression in mice exposed to either a voluntary running disk (RUN), a locked disk (LD), or a locked disk plus social enrichment and tunnels [i.e., a running-independent complex environment (CE)]. RNA sequencing revealed that RUN and CE mice showed distinct, non-overlapping patterns of transcriptomic changes versus the LD control. Bio-informatics uncovered that the RUN and CE environments modulate separate transcriptional networks, biological processes, cellular compartments and molecular pathways, with RUN preferentially regulating synaptic and growth-related pathways and CE altering extracellular matrix-related functions. Within the RUN group, high-distance runners also showed selective stress pathway alterations that correlated with a drastic decline in overall transcriptional changes, suggesting that excess running causes a stress-induced suppression of running's genetic effects. Our findings reveal stimulus-dependent transcriptional signatures of EE on the DG, and provide a resource for generating unbiased, data-driven hypotheses for novel mediators of EE-induced cognitive changes.

  7. Environmental status of FR Yugoslavia

    International Nuclear Information System (INIS)

    Stojanovic, B.

    2002-01-01

    This paper reviews key characteristics of environmental situation in Yugoslavia before, during and after NATO bombing against this country. Principal environmental problems and their sources are described. The 'quality' of soil, water and air, as well as some other environmental parameters is documented by available data during last decade. An analysis of main environmental issues was made. Short review of key environmental policies, instruments and institutions is also presented. (author)

  8. Foraging behavior, environmental parameters and nests development of Melipona colimana Ayala (Hymenoptera: Meliponini in temperate climate of Jalisco, México

    Directory of Open Access Journals (Sweden)

    J. O. Macías-Macías

    Full Text Available Abstract Melipona colimana Ayala is an endemic species inhabiting temperate forests of pine and oak of south of Jalisco in Mexico. During a year, it was recorded every 15 days foraging activity, environmental parameters and the development of colonies of M. colimana in its wild habitat. For five minutes every hour from 7:00 to 21:00, the bees that entered and left the hive and bringing pollen and resin were registered. Every hour the relative humidity, temperature, wind speed and light intensity was recorded and related to foraging activity. Additionally, the weight of the colonies recently transferred to wooden boxes, the number of brood combs, honey pots and pollen were registered. The time of beginning and ending of the foraging activity differs from the reports of stingless bees of tropical weather and the same happens with the pollen collection. The environmental parameters that affect other tropical stingless bees in the foraging activity also affect M. colimana in temperate climate. It was determined that the major activity season and the presence of more pollen pots in the colony is from November through February, for what it could be the best time of the year for the division and obtainance of new colonies, while the critical period of minor activity and pollen flow was during rainy season. These data may be useful for the future sustainable use of this species in temperate climate.

  9. Genetic parameters and environmental effects on temperament score and reproductive traits of Nellore cattle.

    Science.gov (United States)

    Barrozo, D; Buzanskas, M E; Oliveira, J A; Munari, D P; Neves, H H R; Queiroz, S A

    2012-01-01

    Animal temperament is a trait of economic relevance and its use as a selection criterion requires the identification of environmental factors that influence this trait, as well as the estimation of its genetic variability and interrelationship with other traits. The objectives of this study were to evaluate the effect of the covariates dam age at calving (ADC), long yearling age (YA) and long yearling weight (YW) on temperament score (T) and to estimate genetic parameters for T, scrotal circumference (SC) at long YA and age at first calving (AFC) in Nellore cattle participating in a selection program. The traits were analyzed by the restricted maximum likelihood method under a multiple-trait animal model. For all traits, contemporary group was included as a fixed effect and additive genetic and residual as random effects. In addition to these effects, YA, YW and ADC were considered for analyzing T. In the case of SC and AFC, the effect of long YW was included as a covariate. Genetic parameters were estimated for and between traits. The three covariates significantly influenced T. The heritability estimates for T, SC and AFC were 0.18 ± 0.02, 0.53 ± 0.04 and 0.23 ± 0.08, respectively. The genetic correlations between T and SC, and T and AFC were -0.07 ± 0.17 and -0.06 ± 0.19, respectively. The genetic correlation estimated between SC and AFC was -0.57 ± 0.16. In conclusion, a response to selection for T, SC and AFC is expected and selection for T does not imply correlated responses with the other traits.

  10. The Purpose of ISO 14001 Certification: Independent Assurance or Improved Environmental Management System?

    Directory of Open Access Journals (Sweden)

    Janet Morrill

    2012-12-01

    Full Text Available This study provides evidence of the value of third party certification of environmental management systems. We examine the relative importance of improving an environmental management system as a result of certification, versus being able to communicate the quality of that system credibly to outsiders through third party certification. We use survey data where one half of the respondents had indicated that they had an environmental management (EMS in place before seeking ISO 14001 certification, while the other half of respondents did not. Our analyses comparing the two groups find that the group already having an EMS report similar motivations for ISO 14001 certification and perceive to have received similar levels of benefits as firms having no pre-certification EMS. We conclude that even for organizations that already have an EMS, the ability to communicate credibly the quality of that system is a compelling reason to obtain ISO certification.

  11. Relating Magnetic Parameters to Heavy Metal Concentrations and Environmental Factors at Formosa Mine Superfund Site, Douglas County, OR

    Science.gov (United States)

    Upton, T. L.

    2016-12-01

    Advances in the field of environmental magnetism have led to exciting new applications for this field. Magnetic minerals are ubiquitous in the environment and tend to have an affinity for heavy metals. Hence, it has been demonstrated that magnetic properties are often significantly related to concentrations of heavy metals and other pollutants. As a result, magnetic techniques have been used as proxy for determining hot spots of several types of pollution produced from a diversity of anthropogenic sources. Magnetic measurements are non-destructive and relatively inexpensive compared to geochemical analyses. The utility of environmental magnetic methods varies widely depending on biological, chemical and physical processes that create and transform soils and sediments. Applications in the direction of mapping heavy metals have been studied and shown to be quite useful in countries such as China and India but to date, little research has been done in the US. As such, there is need to expand the scope of research to a wider range of soil types and land uses, especially within the US. This study investigates the application of environmental magnetic techniques to mapping of heavy metal concentrations at the Formosa Mine Superfund Site, an abandoned mine about 25 miles southwest of Roseburg, OR. The soils and sediment at this site are derived from pyrite-rich bedrock which is weak in terms of magnetic susceptibility. Using hotspot analysis, correlation and cluster analyses, interactions between metals and magnetic parameters are investigated in relation to environmental factors such as proximity to seeps and adits. Preliminary results suggest significant correlation of magnetic susceptibility with certain heavy metals, signifying that magnetic methods may be useful in mapping heavy metal hotspots at this site. Further analysis examines the relation of various land use differences in magnetic signatures obtained throughout the Cow Creek watershed.

  12. JPRS Report, Environmental Issues

    Science.gov (United States)

    1991-09-13

    open for future generations to exploit the virgin continent. This resulted in an angry response from environmental groups, the Green Peace...so that they can be ahead of their competitors with the use of substitutes for ozone- layer penetrating substances," Möller said. Industry is...Environmental Agency has prompted Mr. Major to set up a Cabinet Office committee to examine the proposals independently while he is on holiday . The

  13. Determination of diffusion parameters of Thermal neutrons for non-moderator media by a pulsed method and a time independent method

    International Nuclear Information System (INIS)

    Boufraqech, A.

    1991-01-01

    Two methods for determining the diffusion parameters of thermal neutrons for non-moderator and non-multiplicator media have been developped: The first one, which is a pulsed method, is based on thermal neutrons relaxation coefficients measurement in a moderator, with and without the medium of interest that plays the role of reflector. For the experimental results interpretation using the diffusion theory, a corrective factor which takes into account the neutron cooling by diffusion has been introduced. Its dependence on the empirically obtained relaxation coefficients is in a good agreement with the calculations made in P3L2 approximation. The difference between linear extrapolation lengths of the moderator and the reflector has been taken into account, by developping the scalar fluxes in Bessel function series which automatically satisfy the boundary conditions at the extra-polated surfaces of the two media. The obtained results for Iron are in a good agreement with those in the literature. The second method is time independent, based on the 'flux albedo' measurements interpretation (Concept introduced by Amaldi and Fermi) by P3 approximation in the one group trans-port theory. The independent sources are introduced in the Marshak boundary conditions. An angular albedo matrix has been used to deal with multiple reflections and to take into account the distortion of the current vector when entring a medium, after being reflected by this latter. The results obtained by this method are slightly different from those given in the literature. The analysis of the possible sources causing this discrepancy, particulary the radial distribution of flux in cylindrical geometry and the flux depression at medium-black body interface, has shown that the origin of this discrepancy is the neutron heating by diffusion. 47 figs., 20 tabs., 39 refs. (author)

  14. PROCEEDINGS OF THE INTERNATIONAL WORKSHOP ON UNCERTAINTY, SENSITIVITY, AND PARAMETER ESTIMATION FOR MULTIMEDIA ENVIRONMENTAL MODELING. EPA/600/R-04/117, NUREG/CP-0187, ERDC SR-04-2.

    Science.gov (United States)

    An International Workshop on Uncertainty, Sensitivity, and Parameter Estimation for Multimedia Environmental Modeling was held August 1921, 2003, at the U.S. Nuclear Regulatory Commission Headquarters in Rockville, Maryland, USA. The workshop was organized and convened by the Fe...

  15. Magnetic fusion: Environmental Readiness Document

    International Nuclear Information System (INIS)

    1981-03-01

    Environmental Readiness Documents are prepared periodically to review and evaluate the environmental status of an energy technology during the several phases of development of that technology. Through these documents, the Office of Environment within the Department of Energy provides an independent and objective assessment of the environmental risks and potential impacts associated with the progression of the technology to the next stage of development and with future extensive use of the technology. This Environmental Readiness Document was prepared to assist the Department of Energy in evaluating the readiness of magnetic fusion technology with respect to environmental issues. An effort has been made to identify potential environmental problems that may be encountered based upon current knowledge, proposed and possible new environmental regulations, and the uncertainties inherent in planned environmental research

  16. Database of Physiological Parameters for Early Life Rats and Mice

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Database of Physiological Parameters for Early Life Rats and Mice provides information based on scientific literature about physiological parameters. Modelers...

  17. Dimension-Independent Likelihood-Informed MCMC

    KAUST Repository

    Cui, Tiangang; Law, Kody; Marzouk, Youssef

    2015-01-01

    Many Bayesian inference problems require exploring the posterior distribution of high-dimensional parameters, which in principle can be described as functions. By exploiting low-dimensional structure in the change from prior to posterior [distributions], we introduce a suite of MCMC samplers that can adapt to the complex structure of the posterior distribution, yet are well-defined on function space. Posterior sampling in nonlinear inverse problems arising from various partial di erential equations and also a stochastic differential equation are used to demonstrate the e ciency of these dimension-independent likelihood-informed samplers.

  18. Dimension-Independent Likelihood-Informed MCMC

    KAUST Repository

    Cui, Tiangang

    2015-01-07

    Many Bayesian inference problems require exploring the posterior distribution of high-dimensional parameters, which in principle can be described as functions. By exploiting low-dimensional structure in the change from prior to posterior [distributions], we introduce a suite of MCMC samplers that can adapt to the complex structure of the posterior distribution, yet are well-defined on function space. Posterior sampling in nonlinear inverse problems arising from various partial di erential equations and also a stochastic differential equation are used to demonstrate the e ciency of these dimension-independent likelihood-informed samplers.

  19. Recharge quantification with radiocarbon: Independent corroboration in three Karoo aquifer studies in Botswana

    International Nuclear Information System (INIS)

    Verhagen, B.Th.; Bredenkamp, D.B.; Janse van Rensburg, H.; Farr, J.L.

    1999-01-01

    Environmental isotope data from a 'snapshot' sampling hold out the promise of producing acceptable estimates of ground water recharge for resource management purposes. In three major ground water developments in Botswana, estimates of recharge to the Karoo aquifers in the Kalahari, were based on residence times derived from radiocarbon data. In the assessment, three factors needed to be considered: 1) the model leading to acceptable values of residence times 2) the initial, or recharge, radiocarbon value and 3) appropriate values of aquifer porosity. In the three studies, porosity had been measured on numerous drill cores obtained from the principal fractured sandstone aquifers. The resulting isotope-based recharge values correspond reasonably with independent recharge assessments using the equal volume method to analyse long-term rest level observations in two cases; in the third, recharge was independently assessed on the basis of chloride balance in both unsaturated and saturated zones. It is concluded that a) the isotope snapshot approach can give acceptable values for recharge in the development of ground water resources, providing rational management information early in the life of a ground water supply scheme; b) the exponential model and an initial radiocarbon values of 85% atmospheric are realistic in this environment and c) the total porosity appears to be the appropriate parameter in the calculation of recharge. This also provides an insight into the behaviour of the aquifers. (author)

  20. Effect of some environmental parameters on fermentative hydrogen production by Enterobacter cloacae DM11

    Energy Technology Data Exchange (ETDEWEB)

    Nath, K.; Kumar, A.; Das, D. [Indian Inst. of Technology, Kharagpur (India). Dept. of Biotechnology, Fermentation Technology Laboratory

    2006-06-15

    This study addressed the issue of using biological systems for hydrogen production as an environmentally sound alternative to conventional thermochemical and electrochemical processes. In particular, it examined the potential for anaerobic fermentation for biological hydrogen production and the possibility of coupling gaseous energy generation with simultaneous treatment of biodegradable waste materials. The study focused on hydrogen production by anaerobic fermentation using Enterobacter cloacae DM11, a Gram-negative, motile facultative anaerobe. Although hydrogen production by these bacteria depends on many environmental parameters, there is very little information on the effects of these factors in the hydrogen production potential of this organism. For that reason, this study examined the effect of initial medium pH, reaction temperature, initial glucose concentration, and iron (Fe2+) concentration on the fermentative production of hydrogen. Fermentative hydrogen production was carried out by Enterobacter cloacae DM11, using glucose as the substrate. Batch cultivations were performed in a 500 ml custom-designed vertical tubular bioreactor. The maximum molar yield of hydrogen was 3.31 mol (mol glucose){sub 1}. The rate and cumulative volume of hydrogen production decreased at higher initial glucose concentration. The pH of 6.5 at a temperature of 37 degrees C was most suitable for maximum rate of production of hydrogen in batch fermentation. The addition of Fe2+ on hydrogen production had a marginal enhancing effect on total hydrogen production. A simple model developed from the modified Gompertz equation was used to fit the cumulative hydrogen production curve and to estimate the hydrogen production potential, maximum production rate, and lag time. It was concluded that these study results could be used in the development of a high rate continuous hydrogen production process. 30 refs., 4 tabs., 3 figs.

  1. Impact parameter analysis and soft QCD dynamics

    International Nuclear Information System (INIS)

    Carvalho, P.A.S.; Martini, A.F.; Menon, M.J.

    2002-01-01

    In a recent paper, based on the hypothesis of light-cone dipole representation for gluon Bremsstrahlung, Kopeliovich et al. developed a dynamical model for the elastic hadronic amplitude. The model has been applied to pp and p (bar) p scattering and the effects of unitarity and peripheral interactions have been investigated in the impact parameter representation. In this communication, making use of a model independent extraction of the scattering amplitude in the impact parameter space (early developed), we represent a comparative study between the predictions from the dynamical model and the impact parameter analysis. (author)

  2. Environmental Monitoring of Microbe Metabolic Transformation

    Science.gov (United States)

    Bebout, Brad (Inventor); Fleming, Erich (Inventor); Piccini, Matthew (Inventor); Beasley, Christopher (Inventor); Bebout, Leslie (Inventor)

    2013-01-01

    Mobile system and method for monitoring environmental parameters involved in growth or metabolic transformation of algae in a liquid. Each of one or more mobile apparati, suspended or partly or wholly submerged in the liquid, includes at least first and second environmental sensors that sense and transmit distinct first and second environmental, growth or transformation parameter values, such as liquid temperature, temperature of gas adjacent to and above the exposed surface, liquid pH, liquid salinity, liquid turbidity, O.sub.2 dissolved in the liquid, CO.sub.2 contained in the liquid, oxidization and reduction potential of the liquid, nutrient concentrations in the liquid, nitrate concentration in the liquid, ammonium concentration in the liquid, bicarbonate concentration in the liquid, phosphate concentration in the liquid, light intensity at the liquid surface, electrical conductivity of the liquid, and a parameter.alpha.(alga) associated with growth stage of the alga, using PAM fluorometry or other suitable parameter measurements.

  3. Hanford Environmental Dose Reconstruction Project

    International Nuclear Information System (INIS)

    Finch, S.M.; McMakin, A.H.

    1992-06-01

    The objective of the Hanford Environmental Dose Reconstruction Project is to estimate the radiation doses that individuals and populations could have received from nuclear operations at Hanford since 1944. The project is being managed and conducted by the Battelle Pacific Northwest Laboratories under contract with the Centers for Disease Control. The independent Technical Steering Panel (TSP) provides technical direction. The project is divided into the following technical tasks. These tasks correspond to the path radionuclides followed, from release to impact on humans (dose estimates): source terms; environmental transport; environmental monitoring data; demography, food consumption, and agriculture; environmental pathways and dose estimates

  4. Ex-post evaluation. Research independency of the basic science study of JAERI

    International Nuclear Information System (INIS)

    Yanagisawa, Kazuaki; Takahashi, Shoji

    2010-06-01

    A research independency was defined here as the continuity and the development of a corresponding research field with an evolution of history. The authors took three fields as research parameters for the ex-post evaluation. They were all belonged to the basic science field studied in the Japan Atomic Energy Research Institute (JAERI). The first parameter was actinides, which was situated in the center of research networking from the viewpoint of socio-economy. The second parameter was positron, which was situated in the periphery of research networking and the third one was neutron, which had competition with other research organizations in Japan. The three were supported and promoted financially by the JAERI. The target year was covered from 1978 to 2002, a 25-years. INIS (International Nuclear Information Systems) operated by the International Atomic Energy Agency (IAEA) was used as the tool for the present bibliometric study. It was revealed that important factors that led the sustainable success of the research independency were the constant efforts to accomplish their mission, the education of their successors to instructing the explicit and tacit research findings and the construction of intellectual networking with learned circles and industries, those were in good collaboration with JAERI. These were quantitatively clarified. Conversely, main factors that impeded the development of the research independency were discontinuance of research caused by a retirement, a change of post or that of occupation, and an unexpected accident (death) of the core researchers. Among three parameters, the authors confirmed that there occurred the time-dependent stage of germination, development and declination of the research independency attributing to the interaction between the succession factors and impeded factors. For this kind of ex-post evaluation, the support of field research laboratory was inevitable. (author)

  5. Dependent vs. independent juvenile survival: contrasting drivers of variation and the buffering effect of parental care.

    Science.gov (United States)

    Dybala, Kristen E; Gardali, Thomas; Eadie, John M

    2013-07-01

    Juvenile survival is often found to be more sensitive than adult survival to variation in environmental conditions, and variation in juvenile survival can have significant impacts on population growth rates and viability. Therefore, understanding the population-level effects of environmental changes requires understanding the effects on juvenile survival. We hypothesized that parental care will buffer the survival of dependent juveniles from variation in environmental conditions, while the survival of independent juveniles will respond more strongly to environmental variation and, in turn, drive the overall variation in annual juvenile survival. We tested this parental-care hypothesis using a 30-year mark-recapture data set to model the survival of juvenile Song Sparrows (Melospiza melodia) during the dependent and independent stages. We examined the effects of weather, density, and cohort mean fledge date and body mass on annual variation in survival during the first 12 weeks after fledging, as well as effects of individual fledge date and body mass on individual variation in survival. The primary driver of annual variation in juvenile survival was precipitation during the previous rainy season, consistent with an effect on food availability, which had a strong positive effect on the survival of independent juveniles, but no effect on dependent juveniles. We also found strong support for effects of body mass and fledge date on individual survival probability, including striking differences in the effect of fledge date by stage. Our results provided evidence that different mechanisms influence juvenile survival during each stage of fledgling development, and that parental care buffers the survival of dependent juveniles from variation in environmental conditions. Consequently, variation in juvenile survival was driven by independent juveniles, not dependent juveniles, and studies focused only on survival during the dependent stage may not be able to detect the

  6. Expanding Model Independent Approaches for Measuring the CKM angle $\\gamma$ at LHCb

    CERN Multimedia

    Prouve, Claire

    2017-01-01

    Model independent approaches to measuring the CKM angle $\\gamma$ in $B\\rightarrow DK$ decays at LHCb are explored. In particular, we consider the case where the $D$ meson decays into a final state with four hadrons. Using four-body final states such as $\\pi^+ \\pi^- \\pi^+ \\pi^-$, $K^+ \\pi^- \\pi^+ \\pi^-$ and $K^+ K^- \\pi^+ \\pi^-$ in addition to traditional 2 and 3 body states and has the potential to significantly improve to the overall constraint on $\\gamma$. There is a significant systematic uncertainty associated with modelling the complex phase of the $D$ decay amplitude across the five-dimensional phase space of the four body decay. It is therefore important to replace these model-dependent quantities with model-independent parameters as input for the $\\gamma$ measurement. These model independent parameters have been measured using quantum-correlated $\\psi(3770) \\rightarrow D^0 \\overline{D^0}$ decays collected by the CLEO-c experiment, and, for $D\\rightarrow K^+ \\pi^- \\pi^+ \\pi^-$, with $D^0-\\overline{D^0...

  7. Reliable Evaluation of Temperature-Independent Parameters in Correlation of Vapour–Liquid Equilibrium Data.

    Czech Academy of Sciences Publication Activity Database

    Pavlíček, Jan; Wichterle, Ivan

    2007-01-01

    Roč. 260, 1 (2007) , s. 70-73 ISSN 0378-3812 R&D Projects: GA ČR(CZ) GA104/03/1555 Institutional research plan: CEZ:AV0Z40720504 Keywords : temperature dependence of parameters * isometric pentanols * correlation Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.506, year: 2007

  8. RNA-Sequencing Reveals Unique Transcriptional Signatures of Running and Running-Independent Environmental Enrichment in the Adult Mouse Dentate Gyrus

    Directory of Open Access Journals (Sweden)

    Catherine-Alexandra Grégoire

    2018-04-01

    Full Text Available Environmental enrichment (EE is a powerful stimulus of brain plasticity and is among the most accessible treatment options for brain disease. In rodents, EE is modeled using multi-factorial environments that include running, social interactions, and/or complex surroundings. Here, we show that running and running-independent EE differentially affect the hippocampal dentate gyrus (DG, a brain region critical for learning and memory. Outbred male CD1 mice housed individually with a voluntary running disk showed improved spatial memory in the radial arm maze compared to individually- or socially-housed mice with a locked disk. We therefore used RNA sequencing to perform an unbiased interrogation of DG gene expression in mice exposed to either a voluntary running disk (RUN, a locked disk (LD, or a locked disk plus social enrichment and tunnels [i.e., a running-independent complex environment (CE]. RNA sequencing revealed that RUN and CE mice showed distinct, non-overlapping patterns of transcriptomic changes versus the LD control. Bio-informatics uncovered that the RUN and CE environments modulate separate transcriptional networks, biological processes, cellular compartments and molecular pathways, with RUN preferentially regulating synaptic and growth-related pathways and CE altering extracellular matrix-related functions. Within the RUN group, high-distance runners also showed selective stress pathway alterations that correlated with a drastic decline in overall transcriptional changes, suggesting that excess running causes a stress-induced suppression of running’s genetic effects. Our findings reveal stimulus-dependent transcriptional signatures of EE on the DG, and provide a resource for generating unbiased, data-driven hypotheses for novel mediators of EE-induced cognitive changes.

  9. Are Independent Fiscal Institutions Really Independent?

    Directory of Open Access Journals (Sweden)

    Slawomir Franek

    2015-08-01

    Full Text Available In the last decade the number of independent fiscal institutions (known also as fiscal councils has tripled. They play an important oversight role over fiscal policy-making in democratic societies, especially as they seek to restore public finance stability in the wake of the recent financial crisis. Although common functions of such institutions include a role in analysis of fiscal policy, forecasting, monitoring compliance with fiscal rules or costing of spending proposals, their roles, resources and structures vary considerably across countries. The aim of the article is to determine the degree of independence of such institutions based on the analysis of the independence index of independent fiscal institutions. The analysis of this index values may be useful to determine the relations between the degree of independence of fiscal councils and fiscal performance of particular countries. The data used to calculate the index values will be derived from European Commission and IMF, which collect sets of information about characteristics of activity of fiscal councils.

  10. Basis-Independent Analysis of the sneutrino Sector in R-Parity Violating Supersymmetry

    International Nuclear Information System (INIS)

    Grossman, Yuval

    2000-01-01

    In R-parity-violating supersymmetric models (with a conserved baryon number), there are no quantum numbers that distinguish the lepton-doublet and down-type Higgs supermultiplets. As a result, the R-parity-violating parameters depend on the basis choice for these superfields, although physical observables are independent of the choice of basis. This paper presents a basis-independent computation of the sneutrino/antisneutrino squared-mass splitting in terms of basis-independent quantities. Techniques are developed for an arbitrary number of sneutrino generations; specific results are provided for the one, two and three generation cases

  11. Analysis of Anderson-Grueneisen parameter under high temperature in alkaline earthoxides

    International Nuclear Information System (INIS)

    Pandey, Vipra; Gupta, Seema; Tomar, D.S.; Goyal, S.C.

    2010-01-01

    The Anderson-Grueneisen parameter (δ) is of considerable importance to Earth scientists because it sets limitations on the thermo-elastic properties of the lower mantle and core. However, there are several formulations on the Grueneisen parameter, which are in frequent use and predict varying dependence of δ as a function of temperature. In this paper, the expressions for thermal expansion, thermal expansion coefficients and bulk modulus are obtained considering the anharmonic dependence on temperature and are applied to study these constants to alkaline earth oxides. Using the derived expressions, we have shown that different parameters on which the Anderson-Grueneisen parameter (δ) depends are temperature dependent, but above all the Anderson-Grueneisen parameter (δ) is independent of temperature. The results obtained have been found to be comparable to experimental data. -- Research Highlights: → The Anderson-Grueneisen parameter (δ) is independent of temperature. → Three parameters, volume coefficient of thermal expansion, bulk modulus, and the Anderson-Grueneisen parameter, can completely describe the thermo-physical behavior of a solid. → Useful in analyzing the thermo-elastic behavior, microscopic behavior, internal structure and other related properties of AEO.

  12. Iterative importance sampling algorithms for parameter estimation

    OpenAIRE

    Morzfeld, Matthias; Day, Marcus S.; Grout, Ray W.; Pau, George Shu Heng; Finsterle, Stefan A.; Bell, John B.

    2016-01-01

    In parameter estimation problems one computes a posterior distribution over uncertain parameters defined jointly by a prior distribution, a model, and noisy data. Markov Chain Monte Carlo (MCMC) is often used for the numerical solution of such problems. An alternative to MCMC is importance sampling, which can exhibit near perfect scaling with the number of cores on high performance computing systems because samples are drawn independently. However, finding a suitable proposal distribution is ...

  13. Effects of particle composition and environmental parameters on catalytic hydrodechlorination of trichloroethylene by nanoscale bimetallic Ni-Fe.

    Science.gov (United States)

    Wei, Jianjun; Qian, Yajing; Liu, Wenjuan; Wang, Lutao; Ge, Yijie; Zhang, Jianghao; Yu, Jiang; Ma, Xingmao

    2014-05-01

    Catalytic nickel was successfully incorporated into nanoscale iron to enhance its dechlorination efficiency for trichloroethylene (TCE), one of the most commonly detected chlorinated organic compounds in groundwater. Ethane was the predominant product. The greatest dechlorination efficiency was achieved at 22 molar percent of nickel. This nanoscale Ni-Fe is poorly ordered and inhomogeneous; iron dissolution occurred whereas nickel was relatively stable during the 24-hr reaction. The morphological characterization provided significant new insights on the mechanism of catalytic hydrodechlorination by bimetallic nanoparticles. TCE degradation and ethane production rates were greatly affected by environmental parameters such as solution pH, temperature and common groundwater ions. Both rate constants decreased and then increased over the pH range of 6.5 to 8.0, with the minimum value occurring at pH 7.5. TCE degradation rate constant showed an increasing trend over the temperature range of 10 to 25°C. However, ethane production rate constant increased and then decreased over the range, with the maximum value occurring at 20°C. Most salts in the solution appeared to enhance the reaction in the first half hour but overall they displayed an inhibitory effect. Combined ions showed a similar effect as individual salts. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

  14. Kinematic parameters of internal waves of the second mode in the South China Sea

    Directory of Open Access Journals (Sweden)

    O. Kurkina

    2017-10-01

    Full Text Available Spatial distributions of the main properties of the mode function and kinematic and non-linear parameters of internal waves of the second mode are derived for the South China Sea for typical summer conditions in July. The calculations are based on the Generalized Digital Environmental Model (GDEM climatology of hydrological variables, from which the local stratification is evaluated. The focus is on the phase speed of long internal waves and the coefficients at the dispersive, quadratic and cubic terms of the weakly non-linear Gardner model. Spatial distributions of these parameters, except for the coefficient at the cubic term, are qualitatively similar for waves of both modes. The dispersive term of Gardner's equation and phase speed for internal waves of the second mode are about a quarter and half, respectively, of those for waves of the first mode. Similarly to the waves of the first mode, the coefficients at the quadratic and cubic terms of Gardner's equation are practically independent of water depth. In contrast to the waves of the first mode, for waves of the second mode the quadratic term is mostly negative. The results can serve as a basis for expressing estimates of the expected parameters of internal waves for the South China Sea.

  15. Joint Integration Office Independent Review Committee annual report, 1985

    International Nuclear Information System (INIS)

    1986-08-01

    Comprised of seven persons with extensive experience in the issues of nuclear waste, the Independent Review Committee (IRC) provides independent and objective review of Defense Transuranic Waste Program (DTWP) activities managed by the Joint Integration Office (JIO), formerly the Defense Transuranic Waste Lead Organization (TLO). The Committee is ensured a broad, interdisciplinary perspective since its membership includes representatives from the fields of nuclear engineering, nuclear waste transportation, industrial quality control, systems and environmental engineering and state and local government. The scope of IRC activities includes overall review of specific TLO plans, projects and activities, and technical review of particular research and development projects. The Committee makes specific suggestions and recommendations based upon expertise in the field of TRU Waste Management. The IRC operates as a consulting group, under an independent charter providing objective review of program activities. This report summarizes the 12 major topics reviewed by the committee during 1985

  16. Environmental parameters altered by climate change affect the activity of soil microorganisms involved in bioremediation.

    Science.gov (United States)

    Alkorta, Itziar; Epelde, Lur; Garbisu, Carlos

    2017-10-16

    Bioremediation, based on the use of microorganisms to break down pollutants, can be very effective at reducing soil pollution. But the climate change we are now experiencing is bound to have an impact on bioremediation performance, since the activity and degrading abilities of soil microorganisms are dependent on a series of environmental parameters that are themselves being altered by climate change, such as soil temperature, moisture, amount of root exudates, etc. Many climate-induced effects on soil microorganisms occur indirectly through changes in plant growth and physiology derived from increased atmospheric CO2 concentrations and temperatures, the alteration of precipitation patterns, etc., with a concomitant effect on rhizoremediation performance (i.e. the plant-assisted microbial degradation of pollutants in the rhizosphere). But these effects are extremely complex and mediated by processes such as acclimation and adaptation. Besides, soil microorganisms form complex networks of interactions with a myriad of organisms from many taxonomic groups that will also be affected by climate change, further complicating data interpretation. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  17. A Sensitivity Analysis Approach to Identify Key Environmental Performance Factors

    Directory of Open Access Journals (Sweden)

    Xi Yu

    2014-01-01

    Full Text Available Life cycle assessment (LCA is widely used in design phase to reduce the product’s environmental impacts through the whole product life cycle (PLC during the last two decades. The traditional LCA is restricted to assessing the environmental impacts of a product and the results cannot reflect the effects of changes within the life cycle. In order to improve the quality of ecodesign, it is a growing need to develop an approach which can reflect the changes between the design parameters and product’s environmental impacts. A sensitivity analysis approach based on LCA and ecodesign is proposed in this paper. The key environmental performance factors which have significant influence on the products’ environmental impacts can be identified by analyzing the relationship between environmental impacts and the design parameters. Users without much environmental knowledge can use this approach to determine which design parameter should be first considered when (redesigning a product. A printed circuit board (PCB case study is conducted; eight design parameters are chosen to be analyzed by our approach. The result shows that the carbon dioxide emission during the PCB manufacture is highly sensitive to the area of PCB panel.

  18. Culture-independent discovery of natural products from soil metagenomes.

    Science.gov (United States)

    Katz, Micah; Hover, Bradley M; Brady, Sean F

    2016-03-01

    Bacterial natural products have proven to be invaluable starting points in the development of many currently used therapeutic agents. Unfortunately, traditional culture-based methods for natural product discovery have been deemphasized by pharmaceutical companies due in large part to high rediscovery rates. Culture-independent, or "metagenomic," methods, which rely on the heterologous expression of DNA extracted directly from environmental samples (eDNA), have the potential to provide access to metabolites encoded by a large fraction of the earth's microbial biosynthetic diversity. As soil is both ubiquitous and rich in bacterial diversity, it is an appealing starting point for culture-independent natural product discovery efforts. This review provides an overview of the history of soil metagenome-driven natural product discovery studies and elaborates on the recent development of new tools for sequence-based, high-throughput profiling of environmental samples used in discovering novel natural product biosynthetic gene clusters. We conclude with several examples of these new tools being employed to facilitate the recovery of novel secondary metabolite encoding gene clusters from soil metagenomes and the subsequent heterologous expression of these clusters to produce bioactive small molecules.

  19. Association study of common variants in the sFRP1 gene region and parameters of bone strength and body composition in two independent healthy Caucasian male cohorts

    DEFF Research Database (Denmark)

    Boudin, Eveline; Piters, Elke; Fransen, Erik

    2012-01-01

    has an influence on bone formation. Therefore this study aimed to investigate the effect of common genetic variation on BMD and bone strength in Caucasian men of different ages. Using HapMap we selected 13 tagSNPs which tag most common genetic variation in and around sFRP1 and we genotyped these SNPs...... parameters. Based on the results of the young cohort we selected three SNPs for further analysis in the complete OAS population. To conclude we tried to replicate the results of two SNPs in an independent population of 994 Belgian men. We found a strong association for rs9694405 with BMI as well in both...

  20. Connections with nature and environmental behaviors.

    Science.gov (United States)

    Geng, Liuna; Xu, Jingke; Ye, Lijuan; Zhou, Wenjun; Zhou, Kexin

    2015-01-01

    The influence of environmental attitudes on environmental behaviors has long been discussed. However, few studies have addressed the foundation of such attitudes. In the present study, we explored primitive belief underlying environmental attitudes, i.e., connections with nature, and its relationship with pro-environmental behaviors. Specifically, we used scales, a computerized Implicit Association Test, and a situational simulation experiment to examine both explicit and implicit connections with nature, both deliberate and spontaneous environmental behaviors, and to find correlations between environmental connectedness and environmental behaviors. Results showed that explicit connectedness was positively correlated with deliberate environmental behaviors, while implicit connectedness was positively correlated with spontaneous environmental behaviors. Additionally, explicit and implicit connectedness was independent of each other. In conclusion, the current study confirms the positive role played by connections with nature in promoting environmental behavior, and accordingly suggests means to encourage pro-environmental behavior by enhancing people's connectedness to nature.

  1. Uncertainty related to Environmental Data and Estimated Extreme Events

    DEFF Research Database (Denmark)

    Burcharth, H. F.

    The design loads on rubble mound breakwaters are almost entirely determined by the environmental conditions, i.e. sea state, water levels, sea bed characteristics, etc. It is the objective of sub-group B to identify the most important environmental parameters and evaluate the related uncertainties...... including those corresponding to extreme estimates typically used for design purposes. Basically a design condition is made up of a set of parameter values stemming from several environmental parameters. To be able to evaluate the uncertainty related to design states one must know the corresponding joint....... Consequently this report deals mainly with each parameter separately. Multi parameter problems are briefly discussed in section 9. It is important to notice that the quantified uncertainties reported in section 7.7 represent what might be regarded as typical figures to be used only when no more qualified...

  2. Participation of Children with Disabilities in Taiwan: The Gap between Independence and Frequency

    Science.gov (United States)

    Hwang, Ai-Wen; Yen, Chia-Feng; Liou, Tsan-Hon; Simeonsson, Rune J.; Chi, Wen-Chou; Lollar, Donald J.; Liao, Hua-Fang; Kang, Lin-Ju; Wu, Ting-Fang; Teng, Sue-Wen; Chiu, Wen-Ta

    2015-01-01

    Background Independence and frequency are two distinct dimensions of participation in daily life. The gap between independence and frequency may reflect the role of the environment on participation, but this distinction has not been fully explored. Methods A total of 18,119 parents or primary caregivers of children with disabilities aged 6.0-17.9 years were interviewed in a cross-sectional nationwide survey with the Functioning Scale of the Disability Evaluation System - Child version (FUNDES-Child). A section consisting of 20 items measured the children’s daily participation in 4 environmental settings: home, neighborhood/community, school, and home/community. Higher independence and frequency restriction scores indicated greater limitation of participation in daily activities. Scores for independence, frequency and independence-frequency gaps were examined across ages along with trend analysis. ANOVA was used to compare the gaps across settings and diagnoses for children with mild levels of severity of impairment. Findings A negative independence-frequency gap (restriction of frequency was greater than that of independence) was found for children with mild to severe levels of impairment. A positive gap (restriction of independence was greater than that of frequency) was found for children with profound levels of severity. The gaps became wider with age in most settings of children with mild impairment and different diagnoses. Widest negative gaps were found for the neighborhood/community settings than for the other three settings for children with mild to severe impairment. Conclusions Children’s participation and independence-frequency gaps depend not only on the severity of their impairments or diagnoses, but also on their age, the setting and the support provided by their environment. In Taiwan, more frequency restrictions than ability restrictions were found for children with mild to moderate severity, especially in the neighborhood/community setting, and

  3. 10 CFR 51.97 - Final environmental impact statement-materials license.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Final environmental impact statement-materials license. 51...-Regulations Implementing Section 102(2) Final Environmental Impact Statements-Materials Licenses § 51.97 Final environmental impact statement—materials license. (a) Independent spent fuel storage installation (ISFSI...

  4. Effects of environmental temperature fluctuations on the parameters of a thermoelectric battery

    International Nuclear Information System (INIS)

    Kozlov, Yu.F.; Oganov, E.P.

    1980-01-01

    A numerical analysis is presented for the effects of lags on the output parameters of a radioisotope thermoelectric battery under conditions of diurnal temperature variation in the environment. Allowance for the inertial effects causes a phase shift and change in amplitude of the variations in the thermal and electrical parameters. The amplitude of the temperature fluctuations in the hot junctions is substantially reduced, while the output electrical power increases. The data provide a more rigorous basis for choosing the parameters of radioisotope batteries during design. 9 refs

  5. Towards Designing Environmentally Stable Conjugated Polymers with very Small Band-Gaps

    International Nuclear Information System (INIS)

    Hong, Sung Y.; Kim, Sung C.

    2003-01-01

    We have investigated substituent effect on the stabilization energies, and nucleus-independent chemical shifts of pentafulvalenes and on the electronic structures of the corresponding polypentafulvalenes to design environmentally stable semiconductive or conductive polymers. Geometrical optimizations of the molecules were carried out at the density functional level of theory with B3LYP hybrid functional and 6-311+G(d) basis set. Stabilization energies were estimated using isodesmic and homodesmotic reactions. As a criterion of aromaticity nucleus-independent chemical shifts of the molecules were computed using GIAO approach. For the polymers the geometrical parameters were optimized through AM1 band calculations and the electronic structures were obtained through modified extended Huckel band calculations. It is found that strong electronwithdrawing substituents increase isodesmic and homodesmotic stabilization energies of pentafulvalene, though it does not increase the aromaticity. Nitro-substituted pentafulvalene is estimated to have stabilization energy as much as azulene. However, substitution either with electron-donating groups or with electronwithdrawing groups does not significantly affect the electronic structures of polypentafulvalene and poly (vinylenedioxypentafulvalene)

  6. The effect of environmental parameters on contaminant uptake by a ...

    African Journals Online (AJOL)

    There was also no discernable relationship between pH and contaminants uptake by the sampling devices as was expected with non polar, non-ioniseable solutes. The uptake of compounds with lower molar volumes was most susceptible to the presence oh humic materials. Journal of Applied Sciences and Environmental ...

  7. Device-independent secret-key-rate analysis for quantum repeaters

    Science.gov (United States)

    Holz, Timo; Kampermann, Hermann; Bruß, Dagmar

    2018-01-01

    The device-independent approach to quantum key distribution (QKD) aims to establish a secret key between two or more parties with untrusted devices, potentially under full control of a quantum adversary. The performance of a QKD protocol can be quantified by the secret key rate, which can be lower bounded via the violation of an appropriate Bell inequality in a setup with untrusted devices. We study secret key rates in the device-independent scenario for different quantum repeater setups and compare them to their device-dependent analogon. The quantum repeater setups under consideration are the original protocol by Briegel et al. [Phys. Rev. Lett. 81, 5932 (1998), 10.1103/PhysRevLett.81.5932] and the hybrid quantum repeater protocol by van Loock et al. [Phys. Rev. Lett. 96, 240501 (2006), 10.1103/PhysRevLett.96.240501]. For a given repeater scheme and a given QKD protocol, the secret key rate depends on a variety of parameters, such as the gate quality or the detector efficiency. We systematically analyze the impact of these parameters and suggest optimized strategies.

  8. Seasonal variation of meteorological factors on air parameters and ...

    African Journals Online (AJOL)

    The impacts of gas flaring on meteorological factors at Ibeno, Eket, Onna, Esit Eket and Umudike - Nigeria were investigated by measuring air quality parameters. The results show that the mean concentration of air parameters value were below Federal Environmental Protection Agency (FEPA) and United States ...

  9. Jensen's Inequality Predicts Effects of Environmental Variation

    Science.gov (United States)

    Jonathan J. Ruel; Matthew P. Ayres

    1999-01-01

    Many biologists now recognize that environmental variance can exert important effects on patterns and processes in nature that are independent of average conditions. Jenson's inequality is a mathematical proof that is seldom mentioned in the ecological literature but which provides a powerful tool for predicting some direct effects of environmental variance in...

  10. Punta Higuero environmental studies

    International Nuclear Information System (INIS)

    Wood, E.D.; Youngbluth, M.J.; Nutt, M.E.; Yeaman, M.N.; Yoshioka, P.; Canoy, M.J.

    1975-01-01

    Site selection surveys and environmental research studies of seven coastal sites in Puerto Rico for construction of power generating facilities were carried out. Data are presented on the physical, chemical, and geological parameters of the Punta Higuero site, and the ecological parameters of zooplankton, benthic invertebrates, and fish communities. Plant associations are included. (U.S.)

  11. Iterative integral parameter identification of a respiratory mechanics model.

    Science.gov (United States)

    Schranz, Christoph; Docherty, Paul D; Chiew, Yeong Shiong; Möller, Knut; Chase, J Geoffrey

    2012-07-18

    Patient-specific respiratory mechanics models can support the evaluation of optimal lung protective ventilator settings during ventilation therapy. Clinical application requires that the individual's model parameter values must be identified with information available at the bedside. Multiple linear regression or gradient-based parameter identification methods are highly sensitive to noise and initial parameter estimates. Thus, they are difficult to apply at the bedside to support therapeutic decisions. An iterative integral parameter identification method is applied to a second order respiratory mechanics model. The method is compared to the commonly used regression methods and error-mapping approaches using simulated and clinical data. The clinical potential of the method was evaluated on data from 13 Acute Respiratory Distress Syndrome (ARDS) patients. The iterative integral method converged to error minima 350 times faster than the Simplex Search Method using simulation data sets and 50 times faster using clinical data sets. Established regression methods reported erroneous results due to sensitivity to noise. In contrast, the iterative integral method was effective independent of initial parameter estimations, and converged successfully in each case tested. These investigations reveal that the iterative integral method is beneficial with respect to computing time, operator independence and robustness, and thus applicable at the bedside for this clinical application.

  12. Chlorination pattern effect on thermodynamic parameters and environmental degradability for C₁₀-SCCPs: Quantum chemical calculation based on virtual combinational library.

    Science.gov (United States)

    Sun, Yuzhen; Pan, Wenxiao; Lin, Yuan; Fu, Jianjie; Zhang, Aiqian

    2016-01-01

    Short-chain chlorinated paraffins (SCCPs) are still controversial candidates for inclusion in the Stockholm Convention. The inherent mixture nature of SCCPs makes it rather difficult to explore their environmental behaviors. A virtual molecule library of 42,720 C10-SCCP congeners covering the full structure spectrum was constructed. We explored the structural effects on the thermodynamic parameters and environmental degradability of C10-SCCPs through semi-empirical quantum chemical calculations. The thermodynamic properties were acquired using the AM1 method, and frontier molecular orbital analysis was carried out to obtain the E(HOMO), E(LUMO) and E(LUMO)-E(HOMO) for degradability exploration at the same level. The influence of the chlorination degree (N(Cl)) on the relative stability and environmental degradation was elucidated. A novel structural descriptor, μ, was proposed to measure the dispersion of the chlorine atoms within a molecule. There were significant correlations between thermodynamic values and N(Cl), while the reported N(Cl)-dependent pollution profile of C10-SCCPs in environmental samples was basically consistent with the predicted order of formation stability of C10-SCCP congeners. In addition, isomers with large μ showed higher relative stability than those with small μ. This could be further verified by the relationship between μ and the reactivity of nucleophilic substitution and OH attack respectively. The C10-SCCP congeners with less Cl substitution and lower dispersion degree are susceptible to environmental degradation via nucleophilic substitution and hydroxyl radical attack, while direct photolysis of C10-SCCP congeners cannot readily occur due to the large E(LUMO)-E(HOMO) values. The chlorination effect and the conclusions were further checked with appropriate density functional theory (DFT) calculations. Copyright © 2015. Published by Elsevier B.V.

  13. Distributed Multi-Sensor Real-Time Building Environmental Parameters Monitoring System with Remote Data Access

    Directory of Open Access Journals (Sweden)

    Beinarts Ivars

    2014-12-01

    Full Text Available In this paper the advanced monitoring system of multiple environmental parameters is presented. The purpose of the system is a long-term estimation of energy efficiency and sustainability for the research test stands which are made of different building materials. Construction of test stands, and placement of main sensors are presented in the first chapter. The structure of data acquisition system includes a real-time interface with sensors and a data logger that allows to acquire and log data from all sensors with fixed rate. The data logging system provides a remote access to the processing of the acquired data and carries out periodical saving at a remote FTP server using an Internet connection. The system architecture and the usage of sensors are explained in the second chapter. In the third chapter implementation of the system, different interfaces of sensors and energy measuring devices are discussed and several examples of data logger program are presented. Each data logger is reading data from analog and digital channels. Measurements can be displayed directly on a screen using WEB access or using data from FTP server. Measurements and acquired data graphical results are presented in the fourth chapter in the selected diagrams. The benefits of the developed system are presented in the conclusion.

  14. Proliferative activity (MIB-1 index) is an independent prognostic parameter in patients with high-grade soft tissue sarcomas of subtypes other than malignant fibrous histiocytomas

    DEFF Research Database (Denmark)

    Jensen, V; Sørensen, Flemming Brandt; Bentzen, S M

    1998-01-01

    . The proliferative activity was assessed by use of the monoclonal antibody MIB-1 and evaluated in multiple, random systematic sampled fields of vision. The percentage of proliferating cells (the MIB-1 index) ranged between 1% and 85% (median 12%). A significant increase in mean MIB-1 index was seen with increasing...... histological malignancy grade. Variation in the incidence of p53 accumulation and bcl-2 positivity among different histological subtypes was observed. p53 accumulation was frequent in synovial sarcomas and leiomyo- and rhabdomyosarcomas, whereas bcl-2 preferentially was expressed in synovial sarcomas....... Univariate analysis identified patient age, tumour size, histological grade of malignancy, MIB-1 index and p53 accumulation as significant prognostic parameters. Multivariate Cox analysis, including tests for interaction terms between histological subtypes and MIB-1 index, showed independent prognostic...

  15. Parameter dependence and outcome dependence in dynamical models for state vector reduction

    International Nuclear Information System (INIS)

    Ghirardi, G.C.; Grassi, R.; Butterfield, J.; Fleming, G.N.

    1993-01-01

    The authors apply the distinction between parameter independence and outcome independence to the linear and nonlinear models of a recent nonrelativistic theory of continuous state vector reduction. It is shown that in the nonlinear model there is a set of realizations of the stochastic process that drives the state vector reduction for which parameter independence is violated for parallel spin components in the EPR-Bohm setup. Such a set has an appreciable probability of occurrence (∼ 1/2). On the other hand, the linear model exhibits only extremely small parameter dependence effects. Some specific features of the models are investigated and it is recalled that, as has been pointed out recently, to be able to speak of definite outcomes (or equivalently of possessed objective elements of reality) at finite times, the criteria for their attribution to physical systems must be slightly changed. The concluding section is devoted to a detailed discussion of the difficulties met when attempting to take, as a starting point for the formulation of a relativistic theory, a nonrelativistic scheme which exhibits parameter dependence. Here the authors derive a theorem which identifies the precise sense in which the occurrence of parameter dependence forbids a genuinely relativistic generalization. Finally, the authors show how the appreciable parameter dependence of the nonlinear model gives rise to problems with relativity, while the extremely weak parameter dependence of the linear model does not give rise to any difficulty, provided the appropriate criteria for the attribution of definite outcomes are taken into account. 19 refs

  16. Determining the optimal number of independent components for reproducible transcriptomic data analysis.

    Science.gov (United States)

    Kairov, Ulykbek; Cantini, Laura; Greco, Alessandro; Molkenov, Askhat; Czerwinska, Urszula; Barillot, Emmanuel; Zinovyev, Andrei

    2017-09-11

    Independent Component Analysis (ICA) is a method that models gene expression data as an action of a set of statistically independent hidden factors. The output of ICA depends on a fundamental parameter: the number of components (factors) to compute. The optimal choice of this parameter, related to determining the effective data dimension, remains an open question in the application of blind source separation techniques to transcriptomic data. Here we address the question of optimizing the number of statistically independent components in the analysis of transcriptomic data for reproducibility of the components in multiple runs of ICA (within the same or within varying effective dimensions) and in multiple independent datasets. To this end, we introduce ranking of independent components based on their stability in multiple ICA computation runs and define a distinguished number of components (Most Stable Transcriptome Dimension, MSTD) corresponding to the point of the qualitative change of the stability profile. Based on a large body of data, we demonstrate that a sufficient number of dimensions is required for biological interpretability of the ICA decomposition and that the most stable components with ranks below MSTD have more chances to be reproduced in independent studies compared to the less stable ones. At the same time, we show that a transcriptomics dataset can be reduced to a relatively high number of dimensions without losing the interpretability of ICA, even though higher dimensions give rise to components driven by small gene sets. We suggest a protocol of ICA application to transcriptomics data with a possibility of prioritizing components with respect to their reproducibility that strengthens the biological interpretation. Computing too few components (much less than MSTD) is not optimal for interpretability of the results. The components ranked within MSTD range have more chances to be reproduced in independent studies.

  17. Environmental surveillance at Hanford for CY-1975 data

    International Nuclear Information System (INIS)

    Blumer, P.J.; Fix, J.J.; Speer, D.R.

    1976-04-01

    This document contains detailed data collected by the Hanford Environmental Surveillance program during 1975. Environmental Surveillance responsibilities at Hanford are divided between Hanford Environmental Health Foundation (HEHF) and Battelle-Northwest (BNW). HEHF is responsible for measuring all nonradiological air quality and sanitary water parameters of interest. BNW is responsible for measuring radiological parameters in all environmental media of significance and for measuring both radiological and nonradiological parameters of Columbia River water and ground water. A brief description of the method and location of sample collection during 1975 is included. Data are tabulated on the content of specific radionuclides in surface air. Columbia River water, drinking water, ground water, foods, fish, and wild animals. Data are also included on content of NO 2 and SO 2 in air, nitrates in Columbia River water, ground water, and drinking water, and water quality of samples of Columbia River water collected at various sampling locations

  18. studies on the correlation of some aggregate parameters in the ...

    African Journals Online (AJOL)

    BARTH EKWUEME

    simulations for problem solving and forecasting environmental conditions .... METHODS. Parameters: The water quality parameters examined were, Turbidity, Total Dissolved Solids (TDS),. Chemical Oxygen Demand (COD), 5-day Biochemical. Oxygen Demand ..... Vogel's Textbook of Quantitative. Chemical Analysis 6th ed ...

  19. Sea surface stability parameters

    International Nuclear Information System (INIS)

    Weber, A.H.; Suich, J.E.

    1978-01-01

    A number of studies dealing with climatology of the Northwest Atlantic Ocean have been published in the last ten years. These published studies have dealt with directly measured meteorological parameters, e.g., wind speed, temperature, etc. This information has been useful because of the increased focus on the near coastal zone where man's activities are increasing in magnitude and scope, e.g., offshore power plants, petroleum production, and the subsequent environmental impacts of these activities. Atmospheric transport of passive or nonpassive material is significantly influenced by the turbulence structure of the atmosphere in the region of the atmosphere-ocean interface. This research entails identification of the suitability of standard atmospheric stability parameters which can be used to determine turbulence structure; the calculation of these parameters for the near-shore and continental shelf regions of the U.S. east coast from Cape Hatteras to Miami, Florida; and the preparation of a climatology of these parameters. In addition, a climatology for average surface stress for the same geographical region is being prepared

  20. Influence of environmental parameters and of their interactions on the release of metal(loid)s from a construction material in hydraulic engineering

    International Nuclear Information System (INIS)

    Schmukat, A.; Duester, L.; Goryunova, E.; Ecker, D.; Heininger, P.; Ternes, T.A.

    2016-01-01

    Highlights: • DoE supported multi-factorial study on the metal(loid) release from copper slag. • Interactions of four parameters were studied and weighted. • An effective separation method between slag and sediment was established. • The metal(loid) partitioning between sediment, slag and eluent is described. • The knowledge on the potential environmental impact of copper slag is increased. - Abstract: Besides the leaching behaviour of a construction material under standardised test-specific conditions with laboratory water, for some construction materials it is advisable to test their environmental behaviour also under close to end use conditions. The envisaged end use combined with the product characteristics (e.g. mineral phases) is decisive for the choice of environmental factors that may change the release of substance that potentially cause adverse environmental effects (e.g. fertilisation or ecotoxicity). At the moment an experimental link is missing between mono-factorial standardised test systems and non standardised complex incubation experiments such as mesocosms which are closer to environmental conditions. Multi-factorial batch experiments may have the potential to close the gap. To verify this, batch experiments with copper slag were performed which is used as armour stones in hydraulic engineering. Design of experiments (DoE) was applied to evaluate the impact of pH, ionic strength, temperature and sediment content on the release of As, Cu, Mo, Ni, Pb, Sb and Zn. The study shows that release and sediment-eluent partitioning of metal(loid)s are impacted by interactions between the studied factors. Under the prevalent test conditions sediment acts as a sink enhancing most strongly the release of elements from the material.

  1. Influence of environmental parameters and of their interactions on the release of metal(loid)s from a construction material in hydraulic engineering

    Energy Technology Data Exchange (ETDEWEB)

    Schmukat, A., E-mail: schmukat@harzwasserwerke.de [Harzwasserwerke GmbH, Zur Granetalsperre 8, 38685 Langelsheim (Germany); Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany); Duester, L. [Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany); Goryunova, E. [Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany); KAPP-Chemie GmbH & Co. KG, Industriestr. 2-4, 56357 Miehlen (Germany); Ecker, D.; Heininger, P.; Ternes, T.A. [Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany)

    2016-03-05

    Highlights: • DoE supported multi-factorial study on the metal(loid) release from copper slag. • Interactions of four parameters were studied and weighted. • An effective separation method between slag and sediment was established. • The metal(loid) partitioning between sediment, slag and eluent is described. • The knowledge on the potential environmental impact of copper slag is increased. - Abstract: Besides the leaching behaviour of a construction material under standardised test-specific conditions with laboratory water, for some construction materials it is advisable to test their environmental behaviour also under close to end use conditions. The envisaged end use combined with the product characteristics (e.g. mineral phases) is decisive for the choice of environmental factors that may change the release of substance that potentially cause adverse environmental effects (e.g. fertilisation or ecotoxicity). At the moment an experimental link is missing between mono-factorial standardised test systems and non standardised complex incubation experiments such as mesocosms which are closer to environmental conditions. Multi-factorial batch experiments may have the potential to close the gap. To verify this, batch experiments with copper slag were performed which is used as armour stones in hydraulic engineering. Design of experiments (DoE) was applied to evaluate the impact of pH, ionic strength, temperature and sediment content on the release of As, Cu, Mo, Ni, Pb, Sb and Zn. The study shows that release and sediment-eluent partitioning of metal(loid)s are impacted by interactions between the studied factors. Under the prevalent test conditions sediment acts as a sink enhancing most strongly the release of elements from the material.

  2. Recommendations for the Preparation of Environmental Assessments and Environmental Impact Statements, 2nd edition

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2004-12-01

    This document provides recommendations for the Department of Energy’s (DOE’s) preparation of environmental assessments and environmental impact statements under the National Environmental Policy Act of 1969 (NEPA). The Office of NEPA Policy and Compliance prepared these recommendations in consultation with the Office of the Assistant General Counsel for Environment and following coordination with the DOE NEPA Community. The recommendations should materially aid those responsible for preparing and reviewing NEPA documents to focus on significant environmental issues, adequately analyze environmental impacts, and effectively present the analysis to decisionmakers and the public. The recommendations are not all-encompassing, however; preparers must apply independent judgment to determine the appropriate scope and analytical requirements of NEPA for each proposal. These recommendations do not constitute legal requirements, but are intended to enhance compliance with existing NEPA regulations (40 CFR Parts 1500-1508, 10 CFR Part 1021).

  3. Technology Integration in EFL Classrooms: A Study of Qatari Independent Schools

    Science.gov (United States)

    Chaaban, Youmen; Ellili-Cherif, Maha

    2017-01-01

    The purpose of this study was to examine the impact of teachers' individual characteristics and perceptions of environmental factors on the extent of technology integration into EFL (English as a Foreign Language) classrooms. To this end, a national survey examining EFL teachers' perceptions was conducted at Qatari Independent Schools. A total of…

  4. A new concept of safety parameter display system

    International Nuclear Information System (INIS)

    Martinez, A.S.; Oliveira, L.F.S. de; Schirru, R.; Thome Filho, Z.D.; Silva, R.A. da.

    1986-07-01

    A general description of Angra-1 Parameter Display System (SSPA), a real time and on-line computerized monitoring system for the parameters related to the power plant safety is presented. This system has the main purpose of diminish the load on the Angra-1 power plant operators at an emergency event by supplying them with the additional tools serving as the basis for a prompt identification of the accident. The SSPA is a kind of safety parameter display system whose concept was introduced after Three Mile Island accident in USA. The SSPA comprises two nuclear applications independently considered. They are included into the Parameters Monitoring Integrated System (SIMP) and the safety critical function system (SFCS). (Author) [pt

  5. Analysis of Petroleum Technology Advances Through Applied Research by Independent Oil Producers

    Energy Technology Data Exchange (ETDEWEB)

    Brashear, Jerry P.; North, Walter B.; Thomas Charles P.; Becker, Alan B.; Faulder, David D.

    2000-01-12

    Petroleum Technology Advances Through Applied Research by Independent Oil Producers is a program of the National Oil Research Program, U.S. Department of Energy. Between 1995 and 1998, the program competitively selected and cost-shared twenty-two projects with small producers. The purpose was to involve small independent producers in testing technologies of interest to them that would advance (directly or indirectly) one or more of four national program objectives: (1) Extend the productive life of reservoirs; (2) Increase production and/or reserves; (3) Improve environmental performance; and (4) Broaden the exchange of technology information.

  6. Environmental parameters affecting the structure of leaf-litter frog (Amphibia: Anura communities in tropical forests: a case study from an Atlantic Rainforest area in southeastern Brazil

    Directory of Open Access Journals (Sweden)

    Carla C. Siqueira

    2014-04-01

    Full Text Available Despite a recent increase of information on leaf litter frog communities from Atlantic rainforests, few studies have analyzed the relationship between environmental parameters and community structure of these animals. We analyzed the effects of some environmental factors on a leaf litter frog community at an Atlantic Rainforest area in southeastern Brazil. Data collection lasted ten consecutive days in January 2010, at elevations ranging between 300 and 520 m above sea level. We established 50 quadrats of 5 x 5 m on the forest floor, totaling 1,250 m² of sampled area, and recorded the mean leaf-litter depth and the number of trees within the plot, as well as altitude. We found 307 individuals belonging to ten frog species within the plots. The overall density of leaf-litter frogs estimated from the plots was 24.6 ind/100m², with Euparkerella brasiliensis (Parker, 1926, Ischnocnema guentheri (Steindachner, 1864, Ischnocnema parva (Girard, 1853 and Haddadus binotatus (Spix, 1824 presenting the highest estimated densities. Among the environmental variables analyzed, only altitude influenced the parameters of anuran community. Our results indicate that the study area has a very high density of forest floor leaf litter frogs at altitudes of 300-500 m. Future estimates of litter frog density might benefit from taking the local altitudinal variation into consideration. Neglecting such variation might result in underestimated/overestimated values if they are extrapolated to the whole area.

  7. Generic models and parameters for assessing the environmental transfer of radionuclides from routine releases

    International Nuclear Information System (INIS)

    1982-01-01

    This report is addressed to national regulatory bodies and technical and administrative personnel responsible for performing environmental impact analyses, in particular for generic assessments of doses to most exposed individuals from routine releases of radioactive effluents to atmospheric and aquatic environments. The concern of society in general for the quality of the environment and the realization that all human activities have some environmental effect, in which actions and reactions are coupled in a complex but predictable manner, have led to the development of a procedure for environmental impact analysis. This procedure is a predictive one, which tries to forecast probable environmental effects before some action, such as the construction and operation of a nuclear power station, is decided upon. The method of prediction is by the application of models that attempt to describe the environmental processes in mathematical terms in order to produce a quantitative result which can be used in the decision-making process

  8. Identifiability of parameters and behaviour of the MCMC chains: a case study using the reaction norm model

    DEFF Research Database (Denmark)

    Shariati, M M; Korsgaard, I R; Sorensen, D

    2009-01-01

    model with unknown covariates (RNUC) is a model in which unknown environmental effects can be inferred jointly with the remaining parameters. The problem of identifiability of parameters at the level of the likelihood and the associated behaviour of MCMC chains were discussed using the RNUC...... as fixed and there are other fixed factors in the model, the contrasts involving environmental effects, the variance of environmental sensitivities (genetic slopes) and the residual variance are the only identifiable parameters. These different identifiability scenarios were generated by changing...... as an example. It was shown theoretically that when environmental effects (covariates) are considered as random effects, estimable functions of the fixed effects, (co)variance components and genetic effects are identifiable as well as the environmental effects. When the environmental effects are treated...

  9. The consequences of disposal of low-level radioactive waste from the Fernald Environmental Management Project: Report of the DOE/Nevada Independent Panel

    International Nuclear Information System (INIS)

    Crowe, B.; Hansen, W.; Waters, R.; Sully, M.; Levitt, D.

    1998-04-01

    The Department of Energy (DOE) convened a panel of independent scientists to assess the performance impact of shallow burial of low-level radioactive waste from the Fernald Environmental Management Project, in light of a transportation incident in December 1997 involving this waste stream. The Fernald waste has been transported to the Nevada Test Site and disposed in the Area 5 Radioactive Waste Management Site (RWMS) since 1993. A separate DOE investigation of the incident established that the waste has been buried in stress-fractured metal boxes, and some of the waste contained excess moisture (high-volumetric water contents). The Independent Panel was charged with determining whether disposition of this waste in the Area 5 RWMS has impacted the conclusions of a previously completed performance assessment in which the site was judged to meet required performance objectives. To assess the performance impact on Area 5, the panel members developed a series of questions. The three areas addressed in these questions were (1) reduced container integrity, (2) the impact of reduced container integrity on subsidence of waste in the disposal pits and (3) excess moisture in the waste. The panel has concluded that there is no performance impact from reduced container integrity--no performance is allocated to the container in the conservative assumptions used in performance assessment. Similarly, the process controlling post-closure subsidence results primarily from void space within and between containers, and the container is assumed to degrade and collapse within 100 years

  10. Environmental cost of using poor decision metrics to prioritize environmental projects.

    Science.gov (United States)

    Pannell, David J; Gibson, Fiona L

    2016-04-01

    Conservation decision makers commonly use project-scoring metrics that are inconsistent with theory on optimal ranking of projects. As a result, there may often be a loss of environmental benefits. We estimated the magnitudes of these losses for various metrics that deviate from theory in ways that are common in practice. These metrics included cases where relevant variables were omitted from the benefits metric, project costs were omitted, and benefits were calculated using a faulty functional form. We estimated distributions of parameters from 129 environmental projects from Australia, New Zealand, and Italy for which detailed analyses had been completed previously. The cost of using poor prioritization metrics (in terms of lost environmental values) was often high--up to 80% in the scenarios we examined. The cost in percentage terms was greater when the budget was smaller. The most costly errors were omitting information about environmental values (up to 31% loss of environmental values), omitting project costs (up to 35% loss), omitting the effectiveness of management actions (up to 9% loss), and using a weighted-additive decision metric for variables that should be multiplied (up to 23% loss). The latter 3 are errors that occur commonly in real-world decision metrics, in combination often reducing potential benefits from conservation investments by 30-50%. Uncertainty about parameter values also reduced the benefits from investments in conservation projects but often not by as much as faulty prioritization metrics. © 2016 Society for Conservation Biology.

  11. Multi-Parameter Estimation for Orthorhombic Media

    KAUST Repository

    Masmoudi, Nabil

    2015-08-19

    Building reliable anisotropy models is crucial in seismic modeling, imaging and full waveform inversion. However, estimating anisotropy parameters is often hampered by the trade off between inhomogeneity and anisotropy. For instance, one way to estimate the anisotropy parameters is to relate them analytically to traveltimes, which is challenging in inhomogeneous media. Using perturbation theory, we develop travel-time approximations for orthorhombic media as explicit functions of the anellipticity parameters η1, η2 and a parameter Δγ in inhomogeneous background media. Specifically, our expansion assumes inhomogeneous ellipsoidal anisotropic background model, which can be obtained from well information and stacking velocity analysis. This approach has two main advantages: in one hand, it provides a computationally efficient tool to solve the orthorhombic eikonal equation, on the other hand, it provides a mechanism to scan for the best fitting anisotropy parameters without the need for repetitive modeling of traveltimes, because the coefficients of the traveltime expansion are independent of the perturbed parameters. Furthermore, the coefficients of the traveltime expansion provide insights on the sensitivity of the traveltime with respect to the perturbed parameters. We show the accuracy of the traveltime approximations as well as an approach for multi-parameter scanning in orthorhombic media.

  12. Multi-Parameter Estimation for Orthorhombic Media

    KAUST Repository

    Masmoudi, Nabil; Alkhalifah, Tariq Ali

    2015-01-01

    Building reliable anisotropy models is crucial in seismic modeling, imaging and full waveform inversion. However, estimating anisotropy parameters is often hampered by the trade off between inhomogeneity and anisotropy. For instance, one way to estimate the anisotropy parameters is to relate them analytically to traveltimes, which is challenging in inhomogeneous media. Using perturbation theory, we develop travel-time approximations for orthorhombic media as explicit functions of the anellipticity parameters η1, η2 and a parameter Δγ in inhomogeneous background media. Specifically, our expansion assumes inhomogeneous ellipsoidal anisotropic background model, which can be obtained from well information and stacking velocity analysis. This approach has two main advantages: in one hand, it provides a computationally efficient tool to solve the orthorhombic eikonal equation, on the other hand, it provides a mechanism to scan for the best fitting anisotropy parameters without the need for repetitive modeling of traveltimes, because the coefficients of the traveltime expansion are independent of the perturbed parameters. Furthermore, the coefficients of the traveltime expansion provide insights on the sensitivity of the traveltime with respect to the perturbed parameters. We show the accuracy of the traveltime approximations as well as an approach for multi-parameter scanning in orthorhombic media.

  13. The universality of the confining potential and the running of the quasi-Coulombic potential constant in the independent-quark model

    International Nuclear Information System (INIS)

    Khruschev, V.V.; Savrin, V.I.; Semenov, S.V.

    1999-01-01

    Parameters of the QCD-motivated static potential and the quark masses are calculated on the basis of the 1 -- meson mass spectra in the framework of the relativistic independent-quark model based on the Dirac equation. The value of the confining potential parameter is found to be (0.20 ± 0.01) GeV 2 for interactions between quarks and antiquarks independently on their flavors. The flavor independence of the confining potential is justified on the 5 x 10 -2 accuracy level both for the heavy quarks and for the light ones. The values of parameter α s , which is a strength of the quasi-Coulombic potential are consistent with the QCD-motivated decrease of α s at small interaction range [ru

  14. Environmental Management Assessment of the Fernald Environmental Management Project (FEMP)

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-01

    This report documents the results of the Environmental Management Assessment performed at the Fernald Environmental Management Project (FEMP) in Fernald, Ohio. During this assessment, the activities conducted by the assessment team included review of internal documents and reports from previous audits and assessments; interviews with US Department of Energy (DOE) and FEMP contractor personnel; and inspection and observation of selected facilities and operations. The onsite portion of the assessment was conducted from March 15 through April 1, 1993, by DOE`s Office of Environmental Audit (EH-24) located within the Office of the Assistant Secretary for Environment, Safety, and Health (EH-1). EH-24 carries out independent assessments of DOE facilities and activities as part of the EH-1 Environment, Safety, and Health (ES&H) Oversight Audit Program. The EH-24 program is designed to evaluate the status of DOE facilities and activities with respect to compliance with Federal, state, and local environmental laws and regulations; compliance with DOE Orders, Guidance and Directives; conformance with accepted industry practices and standards of performance; and the status and adequacy of management systems developed to address environmental requirements. The Environmental Management Assessment of FEMP focused on the adequacy of environmental management systems. Further, in response to requests by the Office of Environmental Restoration and Waste Management (EM) and Fernald Field Office (FN), Quality Assurance and Environmental Radiation activities at FEMP were evaluated from a programmatic standpoint. The results of the evaluation of these areas are contained in the Environmental Protection Programs section in this report.

  15. Environmental Management Assessment of the Fernald Environmental Management Project (FEMP)

    International Nuclear Information System (INIS)

    1993-04-01

    This report documents the results of the Environmental Management Assessment performed at the Fernald Environmental Management Project (FEMP) in Fernald, Ohio. During this assessment, the activities conducted by the assessment team included review of internal documents and reports from previous audits and assessments; interviews with US Department of Energy (DOE) and FEMP contractor personnel; and inspection and observation of selected facilities and operations. The onsite portion of the assessment was conducted from March 15 through April 1, 1993, by DOE's Office of Environmental Audit (EH-24) located within the Office of the Assistant Secretary for Environment, Safety, and Health (EH-1). EH-24 carries out independent assessments of DOE facilities and activities as part of the EH-1 Environment, Safety, and Health (ES ampersand H) Oversight Audit Program. The EH-24 program is designed to evaluate the status of DOE facilities and activities with respect to compliance with Federal, state, and local environmental laws and regulations; compliance with DOE Orders, Guidance and Directives; conformance with accepted industry practices and standards of performance; and the status and adequacy of management systems developed to address environmental requirements. The Environmental Management Assessment of FEMP focused on the adequacy of environmental management systems. Further, in response to requests by the Office of Environmental Restoration and Waste Management (EM) and Fernald Field Office (FN), Quality Assurance and Environmental Radiation activities at FEMP were evaluated from a programmatic standpoint. The results of the evaluation of these areas are contained in the Environmental Protection Programs section in this report

  16. Design parameters and source terms: Volume 3, Source terms

    International Nuclear Information System (INIS)

    1987-10-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report by Stearns Catalytic Corporation (SCC), entitled ''Design Parameters and Source Terms for a Two-Phase Repository in Salt,'' 1985, to the level of the Site Characterization Plan - Conceptual Design Report. The previous unpublished SCC Study identifies the data needs for the Environmental Assessment effort for seven possible Salt Repository sites. 11 refs., 9 tabs

  17. Environmental parameters influence on the dynamics of total and pathogenic Vibrio parahaemolyticus densities in Crassostrea virginica harvested from Mexico's Gulf coast.

    Science.gov (United States)

    López-Hernández, Karla M; Pardío-Sedas, Violeta T; Lizárraga-Partida, Leonardo; Williams, José de J; Martínez-Herrera, David; Flores-Primo, Argel; Uscanga-Serrano, Roxana; Rendón-Castro, Karla

    2015-02-15

    The influence of environmental parameters on the total and pathogenic Vibrio parahaemolyticus seasonal densities in American oysters (Crassostrea virginica) was evaluated for 1 year. Harvesting site A yielded the highest mean densities of V. parahaemolyticus tlh+, tdh+/trh-, tdh-/trh+ and tdh+/trh+ during spring season at 2.57, 1.74, 0.36, and -0.40 log10 MPN/g, respectively, and tdh+/orf8+ during winter season (0.90 log10 MPN/g). V. parahaemolyticus tlh+ densities were associated to salinity (R(2)=0.372, Pturbidity (R(2)=0.597, P<0.035), and orf8+ to temperature, salinity, and pH (R(2)=0.964, P<0.001). The exposure to salinity and temperature conditions during winter and spring seasons regulated the dynamics of V. parahaemolyticus harboring potentially pathogenic genotypes within the oyster. The adaptive response of V. parahaemolyticus to seasonal environmental changes may lead to an increase in survival and virulence, threatening the seafood safety and increasing the risk of illness. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Environmental situation in Austria. Sixth environmental control report

    International Nuclear Information System (INIS)

    Deweis, M.; Kaitna, M.

    2001-01-01

    This sixth environmental control report gives an overall picture of the situation of the environment in Austria for the period from 1997 to 2000. It emphasizes the areas of the Austrian environmental policy where significant improvements were achieved, such as the reduction of air pollutant emissions and the improvement of the quality of running waters. It also deals with problem areas such as transport, climate protection and renewable energy, where new solutions will have to be found within the framework of the Austrian and European environmental policies and already agreed upon strategies will have to be translated into daily practice. This environmental control report was written by experts of the Federal Environment Agency, which is an agency subordinate to the Federal Ministry for Agriculture, Forestry, Environment and Water Management, and which acquired independent status in the form of a limited company. The report gives comprehensive information on all aspects of environmental monitoring in Austria, with a huge amount of numerical, geographical and evaluated data. The report is structured by the following chapters: population and land use; air; global climate change; stratospheric ozone degradation; water; soil; forests; environmental protection; agriculture; traffic; industry; economic audit; waste; contaminated sites; energy; noise; secure handling of chemicals; plant-protective agents; gene technology; radioecology. Those chapters which are in the INIS subject scope, dealing with radioecology and ecological aspects of nuclear and non-nuclear energy are treated individually on analytical level for the INIS database. (a.n.)

  19. Effective time-independent analysis for quantum kicked systems

    Science.gov (United States)

    Bandyopadhyay, Jayendra N.; Guha Sarkar, Tapomoy

    2015-03-01

    We present a mapping of potentially chaotic time-dependent quantum kicked systems to an equivalent approximate effective time-independent scenario, whereby the system is rendered integrable. The time evolution is factorized into an initial kick, followed by an evolution dictated by a time-independent Hamiltonian and a final kick. This method is applied to the kicked top model. The effective time-independent Hamiltonian thus obtained does not suffer from spurious divergences encountered if the traditional Baker-Cambell-Hausdorff treatment is used. The quasienergy spectrum of the Floquet operator is found to be in excellent agreement with the energy levels of the effective Hamiltonian for a wide range of system parameters. The density of states for the effective system exhibits sharp peaklike features, pointing towards quantum criticality. The dynamics in the classical limit of the integrable effective Hamiltonian shows remarkable agreement with the nonintegrable map corresponding to the actual time-dependent system in the nonchaotic regime. This suggests that the effective Hamiltonian serves as a substitute for the actual system in the nonchaotic regime at both the quantum and classical level.

  20. Environmental monitoring around the Nuclear Power Plants (NPPs) in India

    International Nuclear Information System (INIS)

    Ravi, P.M.

    2014-01-01

    Environmental Survey Laboratories (ESLs) are established at all major nuclear installations before the commissioning of an installation. As per the lndian regulations, the environmental monitoring around NPPs are carried out by an independent body. Accordingly, Environmental Survey Laboratories (ESLs) under Health Physics Division, Bhabha Atomic Research Centre is entrusted with the responsibility. This paper presents the various aspects of environmental monitoring programmes being pursued around Indian NPPs

  1. Environmental impact assessment of coal power plants in operation

    Directory of Open Access Journals (Sweden)

    Bartan Ayfer

    2017-01-01

    Full Text Available Coal power plants constitute an important component of the energy mix in many countries. However, coal power plants can cause several environmental risks such as: climate change and biodiversity loss. In this study, a tool has been proposed to calculate the environmental impact of a coal-fired thermal power plant in operation by using multi-criteria scoring and fuzzy logic method. We take into account the following environmental parameters in our tool: CO, SO2, NOx, particulate matter, fly ash, bottom ash, the cooling water intake impact on aquatic biota, and the thermal pollution. In the proposed tool, the boundaries of the fuzzy logic membership functions were established taking into account the threshold values of the environmental parameters which were defined in the environmental legislation. Scoring of these environmental parameters were done with the statistical analysis of the environmental monitoring data of the power plant and by using the documented evidences that were obtained during the site visits. The proposed method estimates each environmental impact factor level separately and then aggregates them by calculating the Environmental Impact Score (EIS. The proposed method uses environmental monitoring data and documented evidence instead of using simulation models. The proposed method has been applied to the 4 coal-fired power plants that have been operation in Turkey. The Environmental Impact Score was obtained for each power plant and their environmental performances were compared. It is expected that those environmental impact assessments will contribute to the decision-making process for environmental investments to those plants. The main advantage of the proposed method is its flexibility and ease of use.

  2. Environmental impact assessment of coal power plants in operation

    Science.gov (United States)

    Bartan, Ayfer; Kucukali, Serhat; Ar, Irfan

    2017-11-01

    Coal power plants constitute an important component of the energy mix in many countries. However, coal power plants can cause several environmental risks such as: climate change and biodiversity loss. In this study, a tool has been proposed to calculate the environmental impact of a coal-fired thermal power plant in operation by using multi-criteria scoring and fuzzy logic method. We take into account the following environmental parameters in our tool: CO, SO2, NOx, particulate matter, fly ash, bottom ash, the cooling water intake impact on aquatic biota, and the thermal pollution. In the proposed tool, the boundaries of the fuzzy logic membership functions were established taking into account the threshold values of the environmental parameters which were defined in the environmental legislation. Scoring of these environmental parameters were done with the statistical analysis of the environmental monitoring data of the power plant and by using the documented evidences that were obtained during the site visits. The proposed method estimates each environmental impact factor level separately and then aggregates them by calculating the Environmental Impact Score (EIS). The proposed method uses environmental monitoring data and documented evidence instead of using simulation models. The proposed method has been applied to the 4 coal-fired power plants that have been operation in Turkey. The Environmental Impact Score was obtained for each power plant and their environmental performances were compared. It is expected that those environmental impact assessments will contribute to the decision-making process for environmental investments to those plants. The main advantage of the proposed method is its flexibility and ease of use.

  3. Development of independent production in Europe: institutional diversity

    International Nuclear Information System (INIS)

    Krause, G.G.

    1995-01-01

    The industrial model of the power sector is being challenged in all but a few countries. Being stable for many years, the power sector is now constrained to evolve to more flexible structures, pushed by financing, political and environmental issues. More so, recent innovations within the financing or entrepreneurial background, as well as in the main equipment suppliers' strategies, have attracted new actors to a formerly closed sector. The independent power production could be seen as a vector leading sector's reforms in several countries, being recognized an a careful path, a way to gradually opening the sector. The analysis of the institutional structures within which the independent production evolves can point out relevant elements and directions of sector's changes. One can find, for instances, within a relatively restraint universe, i.e. that one of the European countries, a variety of situations putting light on the complexity of the debate. This paper aims at discussing the role of the independent power production through such a diversity of institutional structures, avoiding any polarization around themes like privatization or deregulation. (author). 1 fig., 2 tabs., 13 refs

  4. Iterative integral parameter identification of a respiratory mechanics model

    Directory of Open Access Journals (Sweden)

    Schranz Christoph

    2012-07-01

    Full Text Available Abstract Background Patient-specific respiratory mechanics models can support the evaluation of optimal lung protective ventilator settings during ventilation therapy. Clinical application requires that the individual’s model parameter values must be identified with information available at the bedside. Multiple linear regression or gradient-based parameter identification methods are highly sensitive to noise and initial parameter estimates. Thus, they are difficult to apply at the bedside to support therapeutic decisions. Methods An iterative integral parameter identification method is applied to a second order respiratory mechanics model. The method is compared to the commonly used regression methods and error-mapping approaches using simulated and clinical data. The clinical potential of the method was evaluated on data from 13 Acute Respiratory Distress Syndrome (ARDS patients. Results The iterative integral method converged to error minima 350 times faster than the Simplex Search Method using simulation data sets and 50 times faster using clinical data sets. Established regression methods reported erroneous results due to sensitivity to noise. In contrast, the iterative integral method was effective independent of initial parameter estimations, and converged successfully in each case tested. Conclusion These investigations reveal that the iterative integral method is beneficial with respect to computing time, operator independence and robustness, and thus applicable at the bedside for this clinical application.

  5. Independent technical review of the Hanford Tank Farm Operations

    International Nuclear Information System (INIS)

    1992-07-01

    The Independent Technical Assessment of the Hanford Tank Farm Operations was commissioned by the Assistant Secretary for Environmental Restoration and Waste Management on November 1, 1991. The Independent Technical Assessment team conducted on-site interviews and inspections during the following periods: November 18 to 22,1991; April 13 to 17; and April 27 to May 1, 1992. Westinghouse Hanford Company is the management and operating contractor for the Department of Energy at the Hanford site. The Hanford Tank Farm Operations consists of 177 underground storage tanks containing 61 million gallons of high-level radioactive mixed wastes from the chemical reprocessing of nuclear fuel. The Tank Farm Operations also includes associated transfer lines, ancillary equipment, and instrumentation. The Independent Technical Assessment of the Hanford Tank Farm Operations builds upon the prior assessments of the Hanford Waste Vitrification System and the Hanford Site Tank Waste Disposal Strategy.The objective of this technical assessment was to determine whether an integrated and sound program exists to manage the tank-waste storage and tankfarm operations consistent with the Assistant Secretary for Environmental Restoration and Waste Management's guidance of overall risk minimization. The scope of this review includes the organization, management, operation, planning, facilities, and mitigation of the safety-concerns of the Hanford Tank Waste Remediation System. The assessments presented in the body of this report are based on the detailed observations discussed in the appendices. When the assessments use the term ''Hanford'' as an organizational body it means DOE-RL and Westinghouse Hanford Company as a minimum, and in many instances all of the stake holders for the Hanford site

  6. Testing the statistical compatibility of independent data sets

    International Nuclear Information System (INIS)

    Maltoni, M.; Schwetz, T.

    2003-01-01

    We discuss a goodness-of-fit method which tests the compatibility between statistically independent data sets. The method gives sensible results even in cases where the χ 2 minima of the individual data sets are very low or when several parameters are fitted to a large number of data points. In particular, it avoids the problem that a possible disagreement between data sets becomes diluted by data points which are insensitive to the crucial parameters. A formal derivation of the probability distribution function for the proposed test statistics is given, based on standard theorems of statistics. The application of the method is illustrated on data from neutrino oscillation experiments, and its complementarity to the standard goodness-of-fit is discussed

  7. Hanford Environmental Dose Reconstruction Project monthly report

    International Nuclear Information System (INIS)

    Finch, S.M.

    1990-12-01

    The objective of the Hanford Environmental Dose Reconstruction Project is to estimate the radiation doses that populations could have been have received from nuclear operations at Hanford since 1944. The project is being managed and conducted by the Pacific Northwest Laboratory (PNL) under the direction of an independent Technical Steering Panel (TSP). The project is divided into the following technical tasks. These tasks correspond to the path radionuclides followed, from release to impact on humans (dose estimates): source terms; environmental transport; environmental monitoring data; demographics, agriculture, food habits; and environmental pathways and dose estimates. 3 figs., 3 tabs

  8. Time-varying spatial data integration and visualization: 4 Dimensions Environmental Observations Platform (4-DEOS)

    Science.gov (United States)

    Paciello, Rossana; Coviello, Irina; Filizzola, Carolina; Genzano, Nicola; Lisi, Mariano; Mazzeo, Giuseppe; Pergola, Nicola; Sileo, Giancanio; Tramutoli, Valerio

    2014-05-01

    In environmental studies the integration of heterogeneous and time-varying data, is a very common requirement for investigating and possibly visualize correlations among physical parameters underlying the dynamics of complex phenomena. Datasets used in such kind of applications has often different spatial and temporal resolutions. In some case superimposition of asynchronous layers is required. Traditionally the platforms used to perform spatio-temporal visual data analyses allow to overlay spatial data, managing the time using 'snapshot' data model, each stack of layers being labeled with different time. But this kind of architecture does not incorporate the temporal indexing neither the third spatial dimension which is usually given as an independent additional layer. Conversely, the full representation of a generic environmental parameter P(x,y,z,t) in the 4D space-time domain could allow to handle asynchronous datasets as well as less traditional data-products (e.g. vertical sections, punctual time-series, etc.) . In this paper we present the 4 Dimensions Environmental Observation Platform (4-DEOS), a system based on a web services architecture Client-Broker-Server. This platform is a new open source solution for both a timely access and an easy integration and visualization of heterogeneous (maps, vertical profiles or sections, punctual time series, etc.) asynchronous, geospatial products. The innovative aspect of the 4-DEOS system is that users can analyze data/products individually moving through time, having also the possibility to stop the display of some data/products and focus on other parameters for better studying their temporal evolution. This platform gives the opportunity to choose between two distinct display modes for time interval or for single instant. Users can choose to visualize data/products in two ways: i) showing each parameter in a dedicated window or ii) visualize all parameters overlapped in a single window. A sliding time bar, allows

  9. A latent process model for forecasting multiple time series in environmental public health surveillance.

    Science.gov (United States)

    Morrison, Kathryn T; Shaddick, Gavin; Henderson, Sarah B; Buckeridge, David L

    2016-08-15

    This paper outlines a latent process model for forecasting multiple health outcomes arising from a common environmental exposure. Traditionally, surveillance models in environmental health do not link health outcome measures, such as morbidity or mortality counts, to measures of exposure, such as air pollution. Moreover, different measures of health outcomes are treated as independent, while it is known that they are correlated with one another over time as they arise in part from a common underlying exposure. We propose modelling an environmental exposure as a latent process, and we describe the implementation of such a model within a hierarchical Bayesian framework and its efficient computation using integrated nested Laplace approximations. Through a simulation study, we compare distinct univariate models for each health outcome with a bivariate approach. The bivariate model outperforms the univariate models in bias and coverage of parameter estimation, in forecast accuracy and in computational efficiency. The methods are illustrated with a case study using healthcare utilization and air pollution data from British Columbia, Canada, 2003-2011, where seasonal wildfires produce high levels of air pollution, significantly impacting population health. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  10. Socio-Economic and Environmental Impacts of Mining inBotswana ...

    African Journals Online (AJOL)

    On the basis of the findings, it is recommended that there should be an independent medical health team to carry out health impact research, comprehensive socio-economic and environmental impact assessment of the mine, to initiate regular community and institutional consultations and set up an independent air quality ...

  11. P wave dispersion and maximum P wave duration are independently associated with rapid renal function decline.

    Science.gov (United States)

    Su, Ho-Ming; Tsai, Wei-Chung; Lin, Tsung-Hsien; Hsu, Po-Chao; Lee, Wen-Hsien; Lin, Ming-Yen; Chen, Szu-Chia; Lee, Chee-Siong; Voon, Wen-Chol; Lai, Wen-Ter; Sheu, Sheng-Hsiung

    2012-01-01

    The P wave parameters measured by 12-lead electrocardiogram (ECG) are commonly used as noninvasive tools to assess for left atrial enlargement. There are limited studies to evaluate whether P wave parameters are independently associated with decline in renal function. Accordingly, the aim of this study is to assess whether P wave parameters are independently associated with progression to renal end point of ≥25% decline in estimated glomerular filtration rate (eGFR). This longitudinal study included 166 patients. The renal end point was defined as ≥25% decline in eGFR. We measured two ECG P wave parameters corrected by heart rate, i.e. corrected P wave dispersion (PWdisperC) and corrected P wave maximum duration (PWdurMaxC). Heart function and structure were measured from echocardiography. Clinical data, P wave parameters, and echocardiographic measurements were compared and analyzed. Forty-three patients (25.9%) reached renal end point. Kaplan-Meier curves for renal end point-free survival showed PWdisperC > median (63.0 ms) (log-rank P = 0.004) and PWdurMaxC > median (117.9 ms) (log-rank Pfunction decline.

  12. Waste Isolation Pilot Plant: Site environmental report for calendar year 1991

    International Nuclear Information System (INIS)

    1991-01-01

    The US Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Operational Environmental Monitoring Plan (OEMP) monitors a comprehensive set of parameters in order to detect any potential environmental Impacts and establish baselines for future quantitative environmental Impact evaluations. Surface water and groundwater, air, soil, and biotics are measured for background radiation. Nonradiological environmental monitoring activities include air quality, water quality, soil properties, meteorological, and the status of the local biological community. Ecological studies focus on the immediate area surrounding the site with emphasis on the salt storage pile, whereas baseline radiological surveillance covers a broader geographic area Including nearby ranches, villages, and cities. Since the WIPP is still in a preoperational state, and no waste has been received; certain elements required by DOE Order 5400.1 are not presented In this report. The most significant addition to the 1991 report is the inclusion of the first four appendices, the Radiological Baseline Program (DOE/WIPP 92-037), the Salt Impact Studies (DOE/WIPP 92-038), the Disturbed Land Reclamation Techniques (DOE/WIPP 92-039), and the Background Water Characterization for the WIPP (DOE/WIPP 92-013). These appendices are independently published and available to interested parties by the DOE reference number. These summaries will not be published in future ASER'S. They will, however, be referenced as a basis for evaluating similar data collected during the Test and subsequent Operational phases of the WIPP

  13. Phasing of independent laser channels under impact SBS excitation

    Energy Technology Data Exchange (ETDEWEB)

    Gordeev, A A; Efimkov, V F; Zubarev, I G; Mikhailov, S I [P N Lebedev Physics Institute, Russian Academy of Sciences, Moscow (Russian Federation)

    2015-10-31

    It is shown experimentally that phasing of independent laser channels under impact SBS excitation calls for a stable difference in arm lengths, as in a classical Michelson interferometer. A scheme with automatic compensation for fluctuations of interferometer arm lengths has been proposed and experimentally implemented. This scheme makes it possible to perform stable phasing of two laser channels under standard laboratory conditions. (control of radiation parameters)

  14. Prediction of environmental parameters of polycyclic aromatic hydrocarbons with COSMO-RS

    NARCIS (Netherlands)

    Schröder, B.; Santos, L.M.N.B.F.; Alves da Rocha, M.A.; Oliveira, M.B.; Marrucho, I.M.; Coutinho, J.A.P.

    2010-01-01

    The methodology for the prediction of properties of environmental relevance of polycyclic aromatic hydrocarbons based on the conductor-like screening model for real solvents (COSMO-RS/COSMOtherm) is presented and evaluated, with a special focus on the aqueous solubility of polycyclic aromatic

  15. Outcome measures in stapes surgery: postoperative results are independent from preoperative parameters.

    Science.gov (United States)

    Koopmann, Mario; Weiss, Daniel; Savvas, Eleftherios; Rudack, Claudia; Stenner, Markus

    2015-09-01

    The aim of this study was to compare audiometric results before and after stapes surgery and identify potential prognostic factors to appropriately select patients with otosclerosis who will most likely benefit from surgery. We enrolled 126 patients with otosclerosis (162 consecutive ears) in our study who underwent stapes surgery between 2007 and 2012 at our institution. Preoperative and postoperative data including pure-tone audiometry, speech audiometry, stapedial reflex audiometry and surgical data were analyzed. The average preoperative air-bone gap (ABG) was 28.9 ± 8.6 dB. Male patients and patients older than 45 years of age had greater preoperative ABGs in comparison to females and younger patients. Postoperative ABGs were 11.2 ± 7.4 dB. The average ABG gain was 17.7 ± 11.1 dB. Preoperative audiometric data, age, gender and type of surgery did not influence the postoperative results. Stapes surgery offers predictable results independent from disease progression or patient-related factors. While absolute values of hearing improvement are instrumental in reflecting audiometric results of a cohort, relative values better reflect individual's audiometric data resembling the patient's benefit.

  16. Measuruement of transport parameters on multiphase flows

    International Nuclear Information System (INIS)

    Kipphan, H.

    1976-01-01

    A method working on the basis of the correlation measuring technique is developed and tested on gas-solid flows in pipelines to measure transport parameters of the solid phase. Firstly, flows with stationary and site-independent average values are considered; finally, a few data on the measurement of instationary flows follow. (orig.) [de

  17. Environmental processes and parameters influencing the consequences of an accidental release of radioactivity weather and season

    International Nuclear Information System (INIS)

    Boeri, G.C.

    1989-01-01

    Seasonal, climatic and meteorological conditions may have a substantial influence on the physical factors involved in transport and deposition of airborne contaminants, and on the transfer and accumulation of radionuclides in terrestrial and aquatic ecosystems. As well, these environmental conditions can also have a significant influence on living habits and practices, and thus on potential radiological and economical impacts. Moreover, these conditions may affect the features and the impact of countermeasures which are adopted for the protection of the public in case of an accidental release. During a Special Session that the Committee of Radiation Protection and Public Health (CRPPH) held on the 1st-2nd September 1986 to review the radiological aspects of the Chernobyl nuclear accident, it was agreed that a consultant should prepare a report reviewing different accident consequences in a radiation protection and public health perspective, and identify the influence of such parameters as time of the year, weather and environmental conditions on the overall impact and the determination of appropriate countermeasures. A Consultant Report on this issue was prepared, by Dr. G. Boeri, and submitted to the CRPPH for review and consideration at its meeting of 22nd-24th November 1987. The CRPPH subsequently agreed that the Consultant Report should be revised and completed, taking into account comments and suggestions sent to the Secretariat and focussing especially on the effect of seasonal and weather conditions in terms of their influence on the radiological impact of an accident and on the emergency countermeasures to be taken. It was decided that the Consultant Report should be developed into an Overview Paper for a workshop on this issue to be organised by the NEA in 1988

  18. Evaluation of Groundwater Impacts to Support the National Environmental Policy Act Environmental Assessment for the INL Remote-Handled Low-Level Waste Disposal Project

    Energy Technology Data Exchange (ETDEWEB)

    Annette Schafer, Arthur S. Rood, A. Jeffrey Sondrup

    2011-12-23

    Groundwater impacts have been analyzed for the proposed remote-handled low-level waste disposal facility. The analysis was prepared to support the National Environmental Policy Act environmental assessment for the top two ranked sites for the proposed disposal facility. A four-phase screening and analysis approach was documented and applied. Phase I screening was site independent and applied a radionuclide half-life cut-off of 1 year. Phase II screening applied the National Council on Radiation Protection analysis approach and was site independent. Phase III screening used a simplified transport model and site-specific geologic and hydrologic parameters. Phase III neglected the infiltration-reducing engineered cover, the sorption influence of the vault system, dispersion in the vadose zone, vertical dispersion in the aquifer, and the release of radionuclides from specific waste forms. These conservatisms were relaxed in the Phase IV analysis which used a different model with more realistic parameters and assumptions. Phase I screening eliminated 143 of the 246 radionuclides in the inventory from further consideration because each had a half-life less than 1 year. An additional 13 were removed because there was no ingestion dose coefficient available. Of the 90 radionuclides carried forward from Phase I, 57 radionuclides had simulated Phase II screening doses exceeding 0.4 mrem/year. Phase III and IV screening compared the maximum predicted radionuclide concentration in the aquifer to maximum contaminant levels. Of the 57 radionuclides carried forward from Phase II, six radionuclides were identified in Phase III as having simulated future aquifer concentrations exceeding maximum contaminant limits. An additional seven radionuclides had simulated Phase III groundwater concentrations exceeding 1/100th of their respective maximum contaminant levels and were also retained for Phase IV analysis. The Phase IV analysis predicted that none of the thirteen remaining

  19. SCoPE: an efficient method of Cosmological Parameter Estimation

    International Nuclear Information System (INIS)

    Das, Santanu; Souradeep, Tarun

    2014-01-01

    Markov Chain Monte Carlo (MCMC) sampler is widely used for cosmological parameter estimation from CMB and other data. However, due to the intrinsic serial nature of the MCMC sampler, convergence is often very slow. Here we present a fast and independently written Monte Carlo method for cosmological parameter estimation named as Slick Cosmological Parameter Estimator (SCoPE), that employs delayed rejection to increase the acceptance rate of a chain, and pre-fetching that helps an individual chain to run on parallel CPUs. An inter-chain covariance update is also incorporated to prevent clustering of the chains allowing faster and better mixing of the chains. We use an adaptive method for covariance calculation to calculate and update the covariance automatically as the chains progress. Our analysis shows that the acceptance probability of each step in SCoPE is more than 95% and the convergence of the chains are faster. Using SCoPE, we carry out some cosmological parameter estimations with different cosmological models using WMAP-9 and Planck results. One of the current research interests in cosmology is quantifying the nature of dark energy. We analyze the cosmological parameters from two illustrative commonly used parameterisations of dark energy models. We also asses primordial helium fraction in the universe can be constrained by the present CMB data from WMAP-9 and Planck. The results from our MCMC analysis on the one hand helps us to understand the workability of the SCoPE better, on the other hand it provides a completely independent estimation of cosmological parameters from WMAP-9 and Planck data

  20. Stability of Intercellular Exchange of Biochemical Substances Affected by Variability of Environmental Parameters

    Science.gov (United States)

    Mihailović, Dragutin T.; Budinčević, Mirko; Balaž, Igor; Mihailović, Anja

    Communication between cells is realized by exchange of biochemical substances. Due to internal organization of living systems and variability of external parameters, the exchange is heavily influenced by perturbations of various parameters at almost all stages of the process. Since communication is one of essential processes for functioning of living systems it is of interest to investigate conditions for its stability. Using previously developed simplified model of bacterial communication in a form of coupled difference logistic equations we investigate stability of exchange of signaling molecules under variability of internal and external parameters.

  1. Genetic and environmental variance and covariance parameters for some reproductive traits of Holstein and Jersey cattle in Antioquia (Colombia

    Directory of Open Access Journals (Sweden)

    Juan Carlos Zambrano

    2014-03-01

    Full Text Available The objective of this study was to estimate the genetic, phenotypic and environmental parameters for calving interval (CI, days open (DO, number of services per conception (NSC and conception rate (CR in Holstein and Jersey cattle in Antioquia (Colombia. Variance and covariance component estimates were obtained by an animal model that was solved using the derivative-free restricted maximum likelihood method. The means and standard deviations for CI, DO, NSC and CR were: 430.32±77.93 days, 127.15±76.96 days, 1.58±1.03 services per conception and 79.88±28.66% in Holstein cattle, and 409.33±86.48 days, 125.62±86.09 days, 1.48±0.98 services per conception and 84.08±27.23% in Jersey cattle, respectively. The heritability estimates (standard errors were: 0.088(0.037, 0.082(0.037, 0.040(0.025 and 0.030(0.026 in Holstein cattle and 0.072(0.098, 0.090(0.104, 0.093(0.097 and 0.147(0.117 in Jersey cattle, respectively. The results show that the genetic, phenotypic and permanent environmental correlations in the two evaluated breeds were favorable for CI × DO, CI × NSC and DO × NSC, but not for CI × CR, DO × CR and NSC × CR. Genetic and permanent environmental correlations were high in most cases in Holstein cattle, whereas in Jersey cattle they were moderate. In contrast, phenotypic correlations were very low in both breeds, except for CI × DO and NSC × CR, which were high. Overall, the genetic component found was very low (<8% in both evaluated breeds and this implies that their selection would take long time and that a good practical management of the herd will be essential in order to improve the reproductive performance.

  2. Accelerated Dimension-Independent Adaptive Metropolis

    KAUST Repository

    Chen, Yuxin

    2016-10-27

    This work describes improvements by algorithmic and architectural means to black-box Bayesian inference over high-dimensional parameter spaces. The well-known adaptive Metropolis (AM) algorithm [H. Haario, E. Saksman, and J. Tamminen, Bernoulli, (2001), pp. 223--242] is extended herein to scale asymptotically uniformly with respect to the underlying parameter dimension for Gaussian targets, by respecting the variance of the target. The resulting algorithm, referred to as the dimension-independent adaptive Metropolis (DIAM) algorithm, also shows improved performance with respect to adaptive Metropolis on non-Gaussian targets. This algorithm is further improved, and the possibility of probing high-dimensional (with dimension $d \\\\geq 1000$) targets is enabled, via GPU-accelerated numerical libraries and periodically synchronized concurrent chains (justified a posteriori). Asymptotically in dimension, this GPU implementation exhibits a factor of four improvement versus a competitive CPU-based Intel MKL (math kernel library) parallel version alone. Strong scaling to concurrent chains is exhibited, through a combination of longer time per sample batch (weak scaling) with fewer necessary samples to convergence. The algorithm performance is illustrated on several Gaussian and non-Gaussian target examples, in which the dimension may be in excess of one thousand.

  3. Intelligent environmental data warehouse

    International Nuclear Information System (INIS)

    Ekechukwu, B.

    1998-01-01

    Making quick and effective decisions in environment management are based on multiple and complex parameters, a data warehouse is a powerful tool for the over all management of massive environmental information. Selecting the right data from a warehouse is an important factor consideration for end-users. This paper proposed an intelligent environmental data warehouse system. It consists of data warehouse to feed an environmental researchers and managers with desire environmental information needs to their research studies and decision in form of geometric and attribute data for study area, and a metadata for the other sources of environmental information. In addition, the proposed intelligent search engine works according to a set of rule, which enables the system to be aware of the environmental data wanted by the end-user. The system development process passes through four stages. These are data preparation, warehouse development, intelligent engine development and internet platform system development. (author)

  4. ENVIRONMENTAL REPORTING AND CORPORATE GOVERANANCE FOR FTSE 100 LISTED COMPANIES

    Directory of Open Access Journals (Sweden)

    IENCIU IONEL-ALIN

    2012-12-01

    Full Text Available Because environmental information reporting remains voluntary on an international scale, there are major difference in terms of quality and quantity of environmental information, reported by entities from varied sectors and countries. Within this study, I have focused on internal characteristics, consisting mainly in how the entity is managed, in order to identify the existence of certain associations between the characteristics of corporate governance and the existence of environmental reporting. The literature in the field suggests various results related to the correspondence between corporate governance characteristics and environmental reporting. Within the factors suggested by the literature are the board structure, presence of the board committee, the separation between the Chairman of the Board and the Chief Executive Officer, shareholder structure. The paper represent an empirical analyze on how corporate governance characteristics might explain the level of environmental reporting. I suggest a model comprising corporate governance characteristics like: board independence, board size, existence of a Social Responsibility Committee that could explain environmental reporting. The sample comprises 48 companies listed at London Stock Exchange FTSE 100. From FTSE 100 I select only the companies that activates in sectors of activity that may have an impact on the environment such as Aerospace & Defence, Automobiles & Parts, Beverages, Chemicals, Electricity, Food & Drug Retailers, Food Producers, Gas, Water & Multiutilities, General Industrials, Health Care Equipment & Services, Household Goods, Industrial Engineering, Mining, Oil & Gas Producers, Oil Equipment, Services & Distribution, Personal Goods, Pharmaceuticals & Biotechnology, Tobacco. My results show that, from the point of view of the London Stock Exchange FTSE 100 listed companies, the presence of an environmental committee in the board help reduce the conflict of interests between

  5. Soil geochemical parameters influencing the spatial distribution of anthrax in Northwest Minnesota, USA

    International Nuclear Information System (INIS)

    Nath, Samuel; Dere, Ashlee

    2016-01-01

    Bacillus anthracis is the pathogenic bacterium that causes anthrax, which dwells in soils as highly resilient endospores. B. anthracis spore viability in soil is dependent upon environmental conditions, but the soil properties necessary for spore survival are unclear. In this study we used a range of soil geochemical and physical parameters to predict the spatial distribution of B. anthracis in northwest Minnesota, where 64 cases of anthrax in livestock were reported from 2000 to 2013. Two modeling approaches at different spatial scales were used to identify the soil conditions most correlated to known anthrax cases using both statewide and locally collected soil data. Ecological niche models were constructed using the Maximum Entropy (Maxent) approach and included 11 soil parameters as environmental inputs and recorded anthrax cases as known presences. One ecological niche model used soil data and anthrax presences for the entire state while a second model used locally sampled soil data (n = 125) and a subset of anthrax presences, providing a test of spatial scale. In addition, simple logistic regression models using the localized soil data served as an independent measure of variable importance. Maxent model results indicate that at a statewide level, soil calcium and magnesium concentrations, soil pH, and sand content are the most important properties for predicting soil suitability for B. anthracis while at the local level, clay and sand content along with phosphorous and strontium concentrations are most important. These results also show that the spatial scale of analysis is important when considering soil parameters most important for B. anthracis spores. For example, at a broad scale, B. anthracis spores may require Ca-rich soils and an alkaline pH, but may also concentrate in microenvironments with high Sr concentrations. The study is also one of the first ecological niche models that demonstrates the major importance of soil texture for defining

  6. Mutational Profiling Can Establish Clonal or Independent Origin in Synchronous Bilateral Breast and Other Tumors.

    Directory of Open Access Journals (Sweden)

    Lei Bao

    Full Text Available Synchronous tumors can be independent primary tumors or a primary-metastatic (clonal pair, which may have clinical implications. Mutational profiling of tumor DNA is increasingly common in the clinic. We investigated whether mutational profiling can distinguish independent from clonal tumors in breast and other cancers, using a carefully defined test based on the Clonal Likelihood Score (CLS = 100 x # shared high confidence (HC mutations/ # total HC mutations.Statistical properties of a formal test using the CLS were investigated. A high CLS is evidence in favor of clonality; the test is implemented as a one-sided binomial test of proportions. Test parameters were empirically determined using 16,422 independent breast tumor pairs and 15 primary-metastatic tumor pairs from 10 cancer types using The Cancer Genome Atlas.We validated performance of the test with its established parameters, using five published data sets comprising 15,758 known independent tumor pairs (maximum CLS = 4.1%, minimum p-value = 0.48 and 283 known tumor clonal pairs (minimum CLS 13%, maximum p-value 0.99, supporting independence. A plausible molecular mechanism for the shift from hormone receptor positive to triple negative was identified in the clonal pair.We have developed the statistical properties of a carefully defined Clonal Likelihood Score test from mutational profiling of tumor DNA. Under identified conditions, the test appears to reliably distinguish between synchronous tumors of clonal and of independent origin in several cancer types. This approach may have scientific and clinical utility.

  7. Main principles and practices of auditing independence in China: A multifaceted discussion

    NARCIS (Netherlands)

    Lan, W.H.; Georgakopoulos, G.; Sotiropoulos, I.; Galanou, K.

    2010-01-01

    This paper attempts through a review of the associated literature to describe and critically evaluate the audit market in China by exploring the main factors that affect auditor independence. The study identifies that non-audit service and low-balling/price-cutting are not parameters affecting

  8. Multi-parameters scanning in HTI media

    KAUST Repository

    Masmoudi, Nabil

    2014-08-05

    Building credible anisotropy models is crucial in imaging. One way to estimate anisotropy parameters is to relate them analytically to traveltime, which is challenging in inhomogeneous media. Using perturbation theory, we develop traveltime approximations for transversely isotropic media with horizontal symmetry axis (HTI) as explicit functions of the anellipticity parameter η and the symmetry axis azimuth ϕ in inhomogeneous background media. Specifically, our expansion assumes an inhomogeneous elliptically anisotropic background medium, which may be obtained from well information and stacking velocity analysis in HTI media. This formulation has advantages on two fronts: on one hand, it alleviates the computational complexity associated with solving the HTI eikonal equation, and on the other hand, it provides a mechanism to scan for the best fitting parameters η and ϕ without the need for repetitive modeling of traveltimes, because the traveltime coefficients of the expansion are independent of the perturbed parameters η and ϕ. The accuracy of our expansion is further enhanced by the use of shanks transform. We show the effectiveness of our scheme with tests on a 3D model and we propose an approach for multi-parameters scanning in TI media.

  9. Multi-parameters scanning in HTI media

    KAUST Repository

    Masmoudi, Nabil; Alkhalifah, Tariq Ali

    2014-01-01

    Building credible anisotropy models is crucial in imaging. One way to estimate anisotropy parameters is to relate them analytically to traveltime, which is challenging in inhomogeneous media. Using perturbation theory, we develop traveltime approximations for transversely isotropic media with horizontal symmetry axis (HTI) as explicit functions of the anellipticity parameter η and the symmetry axis azimuth ϕ in inhomogeneous background media. Specifically, our expansion assumes an inhomogeneous elliptically anisotropic background medium, which may be obtained from well information and stacking velocity analysis in HTI media. This formulation has advantages on two fronts: on one hand, it alleviates the computational complexity associated with solving the HTI eikonal equation, and on the other hand, it provides a mechanism to scan for the best fitting parameters η and ϕ without the need for repetitive modeling of traveltimes, because the traveltime coefficients of the expansion are independent of the perturbed parameters η and ϕ. The accuracy of our expansion is further enhanced by the use of shanks transform. We show the effectiveness of our scheme with tests on a 3D model and we propose an approach for multi-parameters scanning in TI media.

  10. Independent procedure of checking dose calculations using an independent calculus algorithm; Verificacion independiente de los parametros de planificacion, histogramas dosis volumen, y parametros radiobioligocs mediante el uso de una hoja de calculo automatizada

    Energy Technology Data Exchange (ETDEWEB)

    Perez Rozos, A.; Jerez Sainz, I.; Carrasco Rodriguez, J. L.

    2006-07-01

    In radiotherapy it is recommended the use of an independent procedure of checking dose calculations, in order to verify the main treatment planning system and double check every patient dosimetry. In this work we present and automatic spreadsheet that import data from planning system using IMPAC/RTP format and verify monitor unit calculation using an independent calculus algorithm. Additionally, it perform a personalized analysis of dose volume histograms and several radiobiological parameters like TCP and NTCP. Finally, the application automatically generate a clinical dosimetry report for every patient, including treatment fields, fractionation, independent check results, dose volume analysis, and first day forms. (Author)

  11. Dimension-independent likelihood-informed MCMC

    KAUST Repository

    Cui, Tiangang

    2015-10-08

    Many Bayesian inference problems require exploring the posterior distribution of high-dimensional parameters that represent the discretization of an underlying function. This work introduces a family of Markov chain Monte Carlo (MCMC) samplers that can adapt to the particular structure of a posterior distribution over functions. Two distinct lines of research intersect in the methods developed here. First, we introduce a general class of operator-weighted proposal distributions that are well defined on function space, such that the performance of the resulting MCMC samplers is independent of the discretization of the function. Second, by exploiting local Hessian information and any associated low-dimensional structure in the change from prior to posterior distributions, we develop an inhomogeneous discretization scheme for the Langevin stochastic differential equation that yields operator-weighted proposals adapted to the non-Gaussian structure of the posterior. The resulting dimension-independent and likelihood-informed (DILI) MCMC samplers may be useful for a large class of high-dimensional problems where the target probability measure has a density with respect to a Gaussian reference measure. Two nonlinear inverse problems are used to demonstrate the efficiency of these DILI samplers: an elliptic PDE coefficient inverse problem and path reconstruction in a conditioned diffusion.

  12. Dimension-independent likelihood-informed MCMC

    KAUST Repository

    Cui, Tiangang; Law, Kody; Marzouk, Youssef M.

    2015-01-01

    Many Bayesian inference problems require exploring the posterior distribution of high-dimensional parameters that represent the discretization of an underlying function. This work introduces a family of Markov chain Monte Carlo (MCMC) samplers that can adapt to the particular structure of a posterior distribution over functions. Two distinct lines of research intersect in the methods developed here. First, we introduce a general class of operator-weighted proposal distributions that are well defined on function space, such that the performance of the resulting MCMC samplers is independent of the discretization of the function. Second, by exploiting local Hessian information and any associated low-dimensional structure in the change from prior to posterior distributions, we develop an inhomogeneous discretization scheme for the Langevin stochastic differential equation that yields operator-weighted proposals adapted to the non-Gaussian structure of the posterior. The resulting dimension-independent and likelihood-informed (DILI) MCMC samplers may be useful for a large class of high-dimensional problems where the target probability measure has a density with respect to a Gaussian reference measure. Two nonlinear inverse problems are used to demonstrate the efficiency of these DILI samplers: an elliptic PDE coefficient inverse problem and path reconstruction in a conditioned diffusion.

  13. SMATASY. A Program for the model independent description of the Z resonance

    International Nuclear Information System (INIS)

    Kirsch, S.; Riemann, T.

    1994-07-01

    SMATASY is an interface for the ZF I T T ER package and may be used for the model independent description of the Z resonance at LEP 1 and SLC. It allows the determination of the Z mass and width and its resonance shape parameters r and j for cross-sections and their asymmetries. The r describes the peak height and j the interference of the Z resonance with photon exchange in each scattering channel and for σ T , σ FB , σ lr , σ pol etc. separately. Alternatively, the helicity amplitudes for a given scattering channel may be determined. We compare our formalism with other model independent approaches. The model independent treatment of QED corrections in SMATASY is applicable also far away from the Z peak. (orig.)

  14. Environmental Contamination of Normal Speech.

    Science.gov (United States)

    Harley, Trevor A.

    1990-01-01

    Environmentally contaminated speech errors (irrelevant words or phrases derived from the speaker's environment and erroneously incorporated into speech) are hypothesized to occur at a high level of speech processing, but with a relatively late insertion point. The data indicate that speech production processes are not independent of other…

  15. Quark masses: An environmental impact statement

    International Nuclear Information System (INIS)

    Jaffe, Robert L.; Jenkins, Alejandro; Kimchi, Itamar

    2009-01-01

    We investigate worlds that lie on a slice through the parameter space of the standard model over which quark masses vary. We allow as many as three quarks to participate in nuclei, while fixing the mass of the electron and the average mass of the lightest baryon flavor multiplet. We classify as congenial worlds that satisfy the environmental constraint that the quark masses allow for stable nuclei with charge one, six, and eight, making organic chemistry possible. Whether a congenial world actually produces observers capable of measuring those quark masses depends on a multitude of historical contingencies, beginning with primordial nucleosynthesis and including other astrophysical processes, which we do not explore. Such constraints may be independently superimposed on our results. Environmental constraints such as the ones we study may be combined with information about the a priori distribution of quark masses over the landscape of possible universes to determine whether the measured values of the quark masses are determined environmentally, but our analysis is independent of such an anthropic approach. We estimate baryon masses as functions of quark masses via first-order perturbation theory in flavor SU(3) breaking. We estimate nuclear masses as functions of the baryon masses using two separate tools: for a nucleus made of two baryon species, when possible we consider its analog in our world, a nucleus with a similar binding energy, up to Coulomb contributions. For heavy nuclei or nuclei made of more than two baryons, we develop a generalized Weizsaecker semiempirical mass formula, in which strong kinematic flavor symmetry violation is modeled by a degenerate Fermi gas . We check for the stability of nuclei against fission, strong particle emission (analogous to α decay), and weak nucleon emission. For two light quarks with charges 2/3 and -1/3 , we find a band of congeniality roughly 29 MeV wide in their mass difference, with our own world lying comfortably

  16. Environmental indicators for buildings

    DEFF Research Database (Denmark)

    Dammann, S.

    Whenever we shop, the products we consider buying are labelled with the economical price we have to pay if we want to purchase them - an important parameter in our decisions as purchasers. The increrasing awareness for environmental limits and backlashes of human activities also in the building...... sector have fostered the wish to define 'the ecological price' of a building as a help for environmental conscious decision-making. In a social constructivist approach this Ph.D. thesis looks across and beyond the manifold existing approaches for environmental indicators for buildings. It acknowledges...... in the Netherlands. It identifies lines of conflict and areas of consent betweeen the relevant actors and elaborates scenarios for a possible closure of ongoing debate about environmental indicators for buildings....

  17. Null Environmental Effects of the Cosmic Web on Dark Matter Halo Properties

    Science.gov (United States)

    Goh, Tze; Primack, Joel; Aragon-Calvo, Miguel; Hellinger, Doug; Rodriguez-Puebla, Aldo; Lee, Christoph; Eckleholm, Elliot; Johnston, Kathryn

    2018-01-01

    We study the effects of the cosmic web environment (filaments, voids and walls) and environmental density on key properties of dark matter halos at redshift z = 0 using the Bolshoi-Planck ΛCDM. The z=0 Bolshoi-Planck simulation is analysed into filaments, voids and walls using the SpineWeb method, as well as VIDE method, both of which use Voronoi tessellation and the watershed transform. The key halo properties that we study are the mass accretion rate, spin parameter, concentration, prolateness, scale factor of the last major merger, and scale factor when the halo had half of its z=0 mass. For all these properties, we find that there is no discernible difference between the halo properties in filaments, walls or voids when compared at the same environmental density. As a result, we conclude that environmental density is the core attribute that affects these properties. This conclusion is in line with recent findings that properties of galaxies in redshift surveys are independent of their cosmic web environment at the same environmental density. We also find that the local web environment of the Milky Way and the Andromeda galaxy near the centre of a cosmic wall does not appear to have any effect on the key properties of these galaxies' dark matter halos, although we find that it is rather rare to have such massive halos near the centre of a relatively small cosmic wall.

  18. Edge Cut Domination, Irredundance, and Independence in Graphs

    OpenAIRE

    Fenstermacher, Todd; Hedetniemi, Stephen; Laskar, Renu

    2016-01-01

    An edge dominating set $F$ of a graph $G=(V,E)$ is an \\textit{edge cut dominating set} if the subgraph $\\langle V,G-F \\rangle$ is disconnected. The \\textit{edge cut domination number} $\\gamma_{ct}(G)$ of $G$ is the minimum cardinality of an edge cut dominating set of $G.$ In this paper we study the edge cut domination number and investigate its relationships with other parameters of graphs. We also introduce the properties edge cut irredundance and edge cut independence.

  19. Habitat disturbance and hydrological parameters determine the body size and reproductive strategy of alluvial ground beetles.

    Science.gov (United States)

    Gerisch, Michael

    2011-01-01

    Environmental variability is the main driver for the variation of biological characteristics (life-history traits) of species. Therefore, life-history traits are particularly suited to identify mechanistic linkages between environmental variability and species occurrence and can help in explaining ecological patterns. For ground beetles, few studies directly related species traits to environmental variables. This study aims to analyse how life-history traits of alluvial ground beetles are controlled by environmental factors. I expected that the occurrence of species and the occurrence of specific traits are closely related to hydrological and disturbance parameters. Furthermore I expected most of the trait-variation to be explained by a combination of environmental variables, rather than by their isolated effects. Ground beetles were sampled in the year 2005 in floodplain grassland along the Elbe River in Germany. I used redundancy analysis to quantify the effects of hydrological, sediment, and disturbance related parameters on both species occurrence and species traits. I applied variation partitioning to analyse which environmental compartments explain most of the trait variation. Species occurrence and trait variation were both mainly controlled by hydrological and flood disturbance parameters. I could clearly identify reproductive traits and body size as key traits for floodplain ground beetles to cope with the environmental variability. Furthermore, combinations of hydrological, habitat disturbance, habitat type, and species diversity parameters, rather than their isolated effects, explained large parts of ground beetle trait variation. Thus, a main conclusion of this study is that ground beetle occurrence is mainly determined by complex, multi-scale interactions between environmental variability and their life-history traits.

  20. Cultural Variability in the Link Between Environmental Concern and Support for Environmental Action.

    Science.gov (United States)

    Eom, Kimin; Kim, Heejung S; Sherman, David K; Ishii, Keiko

    2016-10-01

    Research on sustainability behaviors has been based on the assumption that increasing personal concerns about the environment will increase proenvironmental action. We tested whether this assumption is more applicable to individualistic cultures than to collectivistic cultures. In Study 1, we compared 47 countries ( N = 57,268) and found that they varied considerably in the degree to which environmental concern predicted support for proenvironmental action. National-level individualism explained the between-nation variability above and beyond the effects of other cultural values and independently of person-level individualism. In Study 2, we compared individualistic and collectivistic nations (United States vs. Japan; N = 251) and found culture-specific predictors of proenvironmental behavior. Environmental concern predicted environmentally friendly consumer choice among European Americans but not Japanese. For Japanese participants, perceived norms about environmental behavior predicted proenvironmental decision making. Facilitating sustainability across nations requires an understanding of how culture determines which psychological factors drive human action.

  1. Design parameters and source terms: Volume 2, Source terms: Revision 0

    International Nuclear Information System (INIS)

    1987-10-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report by Stearns Catalytic Corporation (SCC), entitled ''Design Parameters and Source Terms for a Two-Phase Repository Salt,'' 1985, to the level of the Site Characterization Plan - Conceptual Design Report. The previous unpublished SCC Study identifies the data needs for the Environmental Assessment effort for seven possible Salt Repository sites. 2 tabs

  2. Consumer and producer environmental responsibility. Comparing two approaches

    International Nuclear Information System (INIS)

    Rodrigues, Joao; Domingos, Tiago

    2008-01-01

    Two different indicators of 'environmental responsibility' were independently proposed by Rodrigues et al. [Rodrigues, J., Domingos, T., Giljum, S., Schneider, F., 2006. Designing an indicator of environmental responsibility. Ecological Economics, 59 (3): 256-266.] and Lenzen et al. [Lenzen, M., Murray, J., Sack, F., Wiedmann, T., 2007. Shared producer and consumer responsibility - theory and practice. Ecological Economics, 61: 27-42.]. These indicators are both supposed to reflect the indirect effects of consumer and producer behavior in the generation of environmental pressure. In this paper we compare their mathematical properties and interpretation. We conclude that they have different implications for environmental policy. (author)

  3. Recommendations concerning models and parameters best suited to breeder reactor environmental radiological assessments

    International Nuclear Information System (INIS)

    Miller, C.W.; Baes, C.F. III; Dunning, D.E. Jr.

    1980-05-01

    Recommendations are presented concerning the models and parameters best suited for assessing the impact of radionuclide releases to the environment by breeder reactor facilities. These recommendations are based on the model and parameter evaluations performed during this project to date. Seven different areas are covered in separate sections

  4. Systematic and random erros in lattice parameter determinations

    International Nuclear Information System (INIS)

    Nascimento, E.M.

    1980-01-01

    A new method is proposed for evaluation of diffraction data used in precise determination of lattice parameters. The method is based on separation and systematic erros on the diffraction angles level, where the randon part of erros is independent on the 0 angle. The separation is enable by assumption that the systematic part of erros depends on the 0 angle linearly. In that situation the high precision in lattice parameters determination is related more to reducing the randon errors content that to the presence of unremoved systematic errors. (Author) [pt

  5. Exploring control parameters of two photon processes in solutions

    Indian Academy of Sciences (India)

    Here, we present the effect of several control parameters on the TPA process that are independent of .... as the typical selection rules and pathways of mole- cular transitions for ..... Inset in the graph shows the 780 beam spec- tra at two ...

  6. 76 FR 63311 - National Institute of Environmental Health Sciences; Notice of Closed Meetings

    Science.gov (United States)

    2011-10-12

    ... Environmental Health Sciences; Notice of Closed Meetings Pursuant to section 10(d) of the Federal Advisory... Environmental Health Sciences, Office of Program Operations, Scientific Review Branch, P.O. Box 12233, Research... Environmental Health Sciences Special Emphasis Panel, Development to Independence Review Meeting. Date: November...

  7. 40 CFR 91.406 - Engine parameters to be measured and recorded.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine parameters to be measured and recorded. 91.406 Section 91.406 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Procedures § 91.406 Engine parameters to be measured and recorded. Measure or calculate, then record, the...

  8. 40 CFR 90.406 - Engine parameters to be measured and recorded.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine parameters to be measured and recorded. 90.406 Section 90.406 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Gaseous Exhaust Test Procedures § 90.406 Engine parameters to be measured and recorded. Measure or...

  9. ECOS: values of parameters to be used for domestic animals

    International Nuclear Information System (INIS)

    Thorne, M.C.

    1984-03-01

    This report constitutes the database description for the domestic animals section of the biosphere code ECOS. Two categories of data are supplied, element-independent and element-dependent. The element-independent data comprise rates of food, water and soil consumption, inhalation rates and masses of animal tissues. The element-dependent data consist of f 1 (fractional gastrointestinal absorption), fsub(D) (fractional systematic deposition after inhalation) and NRF (weighted integrated retention function) values. All parameter values given are justified. (author)

  10. Model- and calibration-independent test of cosmic acceleration

    International Nuclear Information System (INIS)

    Seikel, Marina; Schwarz, Dominik J.

    2009-01-01

    We present a calibration-independent test of the accelerated expansion of the universe using supernova type Ia data. The test is also model-independent in the sense that no assumptions about the content of the universe or about the parameterization of the deceleration parameter are made and that it does not assume any dynamical equations of motion. Yet, the test assumes the universe and the distribution of supernovae to be statistically homogeneous and isotropic. A significant reduction of systematic effects, as compared to our previous, calibration-dependent test, is achieved. Accelerated expansion is detected at significant level (4.3σ in the 2007 Gold sample, 7.2σ in the 2008 Union sample) if the universe is spatially flat. This result depends, however, crucially on supernovae with a redshift smaller than 0.1, for which the assumption of statistical isotropy and homogeneity is less well established

  11. Tortuguero Bay [Puerto Rico] environmental studies

    International Nuclear Information System (INIS)

    Wood, E.D.; Youngbluth, M.J.; Nutt, M.E.; Yoshioka, P.; Canoy, M.J.

    1975-01-01

    Site selection surveys and environmental research studies of seven coastal sites in Puerto Rico for construction of power generating facilities were carried out. Data are presented on the physical, chemical, and geological parameters of the Tortuguero Bay site, and the ecological parameters of zooplankton, benthic invertebrates, plant and fish communities. (U.S.)

  12. Central Bank independence

    Directory of Open Access Journals (Sweden)

    Vasile DEDU

    2012-08-01

    Full Text Available In this paper we present the key aspects regarding central bank’s independence. Most economists consider that the factor which positively influences the efficiency of monetary policy measures is the high independence of the central bank. We determined that the National Bank of Romania (NBR has a high degree of independence. NBR has both goal and instrument independence. We also consider that the hike of NBR’s independence played an important role in the significant disinflation process, as headline inflation dropped inside the targeted band of 3% ± 1 percentage point recently.

  13. Multi-parameter observation of environmental asbestos pollution at the Institut de Physique du Globe de Paris (Jussieu Campus, France).

    Science.gov (United States)

    Besson, P; Lalanne, F X; Wang, Y; Guyot, F

    1999-11-01

    An original multi-parameter system has been used to study the nature of dust in the ambient air, particularly the total fibers and asbestos fibers, in eight areas of the Institut de Physique de Globe de Paris (France). These analyses provide a detailed case study of environmental pollution by asbestos fibers at low levels. The levels of total fibers with a length greater than 3 microns, measured with a real time fiber analyser monitor (FAM), give a baseline of 2.5 fibers per l., throughout the duration of sampling. The same levels, calculated during periods of effective presence of staff, are smaller than 10 fb per l. During these periods, the instantaneous value can show high peaks, reaching a maximum of 60 fb per l., but more often of about 5 to 10 fb per l. A direct cause and effect relationship exists between fiber concentrations and the presence of people, and indirectly with the variation of the other environmental parameters (temperature, humidity, air velocity). The baseline concentration of asbestos fibers, determined by analytical transmission electron microscopy (ATEM), is about 10(-1) fb per l., with a mean value during the presence of people always less than 1.5 fb per l. The low levels of asbestos fibers do not allow us to establish a precise correlation between the concentration of total fibers and the asbestos concentration, but a rough estimate suggests that asbestos could represent 10-20% of the airborne fibers monitored with the FAM. The statistical study of fiber sizes shows that 70 and 55% of analyzed chrysotile and amosite fibers respectively are smaller than 5 microns. These numbers are 40 and 35% for fibers smaller than 3 microns, which are undetected by the FAM. Amosite, which characterizes most of the asbestos-containing materials (ACM) in the analyzed areas, is detected in the ambient air in quantities ten times less important than chrysotile. The low asbestos levels and the difference between the nature of building asbestos and airborne

  14. Environmental assessment of the Carlsbad Environmental Monitoring and Research Center Facility

    International Nuclear Information System (INIS)

    1995-10-01

    This Environmental Assessment has been prepared to determine if the Carlsbad Environmental Monitoring and Research Center (the Center), or its alternatives would have significant environmental impacts that must be analyzed in an Environmental Impact Statement. DOE's proposed action is to continue funding the Center. While DOE is not funding construction of the planned Center facility, operation of that facility is dependent upon continued funding. To implement the proposed action, the Center would initially construct a facility of approximately 2,300 square meters (25,000 square feet). The Phase 1 laboratory facilities and parking lot will occupy approximately 1.2 hectares (3 acres) of approximately 8.9 hectares (22 acres) of land which were donated to New Mexico State University (NMSU) for this purpose. The facility would contain laboratories to analyze chemical and radioactive materials typical of potential contaminants that could occur in the environment in the vicinity of the DOE Waste Isolation Pilot Plant (WIPP) site or other locations. The facility also would have bioassay facilities to measure radionuclide levels in the general population and in employees of the WIPP. Operation of the Center would meet the DOE requirement for independent monitoring and assessment of environmental impacts associated with the planned disposal of transuranic waste at the WIPP

  15. Environmental assessment of the Carlsbad Environmental Monitoring and Research Center Facility

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    This Environmental Assessment has been prepared to determine if the Carlsbad Environmental Monitoring and Research Center (the Center), or its alternatives would have significant environmental impacts that must be analyzed in an Environmental Impact Statement. DOE`s proposed action is to continue funding the Center. While DOE is not funding construction of the planned Center facility, operation of that facility is dependent upon continued funding. To implement the proposed action, the Center would initially construct a facility of approximately 2,300 square meters (25,000 square feet). The Phase 1 laboratory facilities and parking lot will occupy approximately 1.2 hectares (3 acres) of approximately 8.9 hectares (22 acres) of land which were donated to New Mexico State University (NMSU) for this purpose. The facility would contain laboratories to analyze chemical and radioactive materials typical of potential contaminants that could occur in the environment in the vicinity of the DOE Waste Isolation Pilot Plant (WIPP) site or other locations. The facility also would have bioassay facilities to measure radionuclide levels in the general population and in employees of the WIPP. Operation of the Center would meet the DOE requirement for independent monitoring and assessment of environmental impacts associated with the planned disposal of transuranic waste at the WIPP.

  16. Sandia National Laboratories/New Mexico existing environmental analyses bounding environmental test facilities.

    Energy Technology Data Exchange (ETDEWEB)

    May, Rodney A.; Bailey-White, Brenda E. (Sandia Staffing Alliance, LLC, Albuquerque, NM); Cantwell, Amber (Sandia Staffing Alliance, LLC, Albuquerque, NM)

    2009-06-01

    This report identifies current environmental operating parameters for the various test and support facilities at SNL/NM. The intent of this report is solely to provide the limits which bound the facilities' operations. Understanding environmental limits is important to maximizing the capabilities and working within the existing constraints of each facility, and supports the decision-making process in meeting customer requests, cost and schedule planning, modifications to processes, future commitments, and use of resources. Working within environmental limits ensures that mission objectives will be met in a manner that protects human health and the environment. It should be noted that, in addition to adhering to the established limits, other approvals and permits may be required for specific projects.

  17. Distribution of phytoplankton community in relation to environmental parameters in cage culture area of Sepanggar Bay, Sabah, Malaysia

    Science.gov (United States)

    Sidik, Madihah Jaffar; Rashed-Un-Nabi, Md.; Azharul Hoque, Md.

    2008-11-01

    This paper covers spatial and temporal variation in phytoplankton communities and physico-chemical water properties in the cage culture area of Sepanggar Bay, Sabah, Malaysia based on field measurement conducted during July 2005 to January 2006 to study the spatial and temporal variation in phytoplankton communities and physico-chemical water properties of the bay. Phytoplankton samples and water parameters data were collected from five different stations located inside the bay during Southwest, Interseasonal and Northeast monsoons. Forty phytoplankton genera, representatives of 23 families, were found in the study area with a mean abundance of 1.55 ± 1.19 × 10 6 cells L -1. Most of these genera belong to diatoms (82.17%), Dinoflagellates (17.55%) and cyanobacteria (0.29%). Three genera were found to be dominant (>10%) in phytoplankton abundance and these were Coscinodiscus spp. (36.38%), Chaetoceros spp (17.65%) and Bacteriastrum spp. (10.98%). The most dominant genus was Coscinodiscus spp. which showed high abundance during all monsoons and stations (except Station 3). Among the seven environmental parameters tested in this study, water temperature, pH and suspended sediment concentration were found to be significantly different between monsoons. On the other hand, no significant differences were found between stations for the studied physico-chemical parameters. A clear differences in phytoplankton densities were observed between monsoons and stations with higher mean abundances during interseasonal monsoon (2.40 ± 1.37 × 10 6 cells L -1) and at station five (2.05 ± 0.74 × 10 6 cells L -1), respectively. Conversely, the diversity indices, both Shannon-Wiener (H) and Pielou (J), showed no significant difference throughout stations and monsoons (except (H) for monsoons). Analysis of similarity (ANOSIM) results demonstrated temporal differences in phytoplankton community structure with highly diverse phytoplankton assemblage. Through cluster analysis five

  18. Effects of environmental parameters on the chestnut gall wasp and its complex of indigenous parasitoids

    Science.gov (United States)

    Bonsignore, Carmelo Peter; Bernardo, Umberto

    2018-04-01

    The chestnut gall wasp (CGW), Dryocosmus kuriphilus, an invasive pest native to China, has caused severe yield and economic losses to chestnut production in Europe since its arrival in 2002. In Southern Italy, the complex of indigenous parasitoids colonizing CGW was monitored between 2013 and 2015, with the aim of estimating the composition of the indigenous parasitoid complex, its ability to control CGW populations, and the interactions of both factors with several measured environmental parameters. We compared results among three differently managed field types. Results showed an increase in the rate of parasitism both when the host population density was lower and in unmanaged chestnut stands with more natural conditions. The percentage of parasitism in galls was related to morphological traits of the galls and to higher seasonal temperatures, which reduced the parasitism intensity because CGW develops earlier under such conditions. The host-parasitoid mortality inside galls varied among sites and was associated mostly with rot fungi during wet spring and summer months. Parasitoid species richness was similar among the study sites, but the proportion of parasitoid species differed between orchards and unmanaged coppice stands. The timing of attack by parasitoids followed a species-specific successional sequence throughout the larva-to-adult life cycle of the CGW. These interactions should be considered in future research on trophic relationships and when modeling invasive scenarios for new pest species.

  19. Environmental Sound Perception: Metadescription and Modeling Based on Independent Primary Studies

    Directory of Open Access Journals (Sweden)

    Stephen McAdams

    2010-01-01

    Full Text Available The aim of the study is to transpose and extend to a set of environmental sounds the notion of sound descriptors usually used for musical sounds. Four separate primary studies dealing with interior car sounds, air-conditioning units, car horns, and closing car doors are considered collectively. The corpus formed by these initial stimuli is submitted to new experimental studies and analyses, both for revealing metacategories and for defining more precisely the limits of each of the resulting categories. In a second step, the new structure is modeled: common and specific dimensions within each category are derived from the initial results and new investigations of audio features are performed. Furthermore, an automatic classifier based on two audio descriptors and a multinomial logistic regression procedure is implemented and validated with the corpus.

  20. analysis and correlation of stability parameters in malting barley

    African Journals Online (AJOL)

    Administrator

    food, feed, medicinal purposes and malt of alcoholic beverages. Stability parameters are ... and animal food, health benefits and malting and brewing in many ..... targeted for environmental conditions which are ... Market Update. Available at ...

  1. Integrated environmental monitoring program at the Hanford Site

    International Nuclear Information System (INIS)

    Jaquish, R.E.

    1990-08-01

    The US Department of Energy's Hanford Site, north of Richland, Washington, has a mission of defense production, waste management, environmental restoration, advanced reactor design, and research development. Environmental programs at Hanford are conducted by Pacific Northwest Laboratory (PNL) and the Westinghouse Hanford Company (WHC). The WHC environmental programs include the compliance and surveillance activities associated with site operations and waste management. The PNL environmental programs address the site-wide and the of-site areas. They include the environmental surveillance and the associated support activities, such as dose calculations, and also the monitoring of environmental conditions to comply with federal and state environmental regulations on wildlife and cultural resources. These are called ''independent environmental programs'' in that they are conducted completely separate from site operations. The Environmental Surveillance and Oversight Program consists of the following projects: surface environmental surveillance; ground-water surveillance; wildlife resources monitoring; cultural resources; dose overview; radiation standards and calibrations; meteorological and climatological services; emergency preparedness

  2. Routine environmental audit of the K-25 Site, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    This report documents the results of the Routine Environmental Audit of the K-25 Site in Oak Ridge, Tennessee, conducted February 14 through February 25, 1994, by the US Department of Energy`s (DOE`s) Office of Environmental Audit (EH-24) located within the Office of Environment, Safety and Health (EH). The Routine Environmental Audit for the K-25 site was conducted as an environmental management assessment, supported through reviews of the Waste Management Program and the Decontamination and Decommissioning Program. The assessment was conducted jointly with, and built upon, the results provided by the ``DOE Oak Ridge Operations Office Environment, Safety, health and Quality Assurance Appraisal at the K-25 Site.`` DOE 5482.1B, ``Environment, Safety and Health Appraisal Program,`` established the mission of EH-24 to provide comprehensive, independent oversight of Department-wide environmental programs on behalf of the Secretary of Energy. The purpose of this assessment is to provide the Secretary of Energy and senior DOE managers with concise independent information as part of DOE`s continuing effort to improve environmental program performance. The ultimate goal of EH-24 is enhancement of environmental protection and the minimization of risk to public health and the environment. The routine environmental audit is one method by which EH-24 accomplishes its mission, utilizing systematic and periodic evaluations of the Department`s environmental programs within line organizations.

  3. Routine environmental audit of the K-25 Site, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1994-02-01

    This report documents the results of the Routine Environmental Audit of the K-25 Site in Oak Ridge, Tennessee, conducted February 14 through February 25, 1994, by the US Department of Energy's (DOE's) Office of Environmental Audit (EH-24) located within the Office of Environment, Safety and Health (EH). The Routine Environmental Audit for the K-25 site was conducted as an environmental management assessment, supported through reviews of the Waste Management Program and the Decontamination and Decommissioning Program. The assessment was conducted jointly with, and built upon, the results provided by the ''DOE Oak Ridge Operations Office Environment, Safety, health and Quality Assurance Appraisal at the K-25 Site.'' DOE 5482.1B, ''Environment, Safety and Health Appraisal Program,'' established the mission of EH-24 to provide comprehensive, independent oversight of Department-wide environmental programs on behalf of the Secretary of Energy. The purpose of this assessment is to provide the Secretary of Energy and senior DOE managers with concise independent information as part of DOE's continuing effort to improve environmental program performance. The ultimate goal of EH-24 is enhancement of environmental protection and the minimization of risk to public health and the environment. The routine environmental audit is one method by which EH-24 accomplishes its mission, utilizing systematic and periodic evaluations of the Department's environmental programs within line organizations

  4. Parameter Estimation for Improving Association Indicators in Binary Logistic Regression

    Directory of Open Access Journals (Sweden)

    Mahdi Bashiri

    2012-02-01

    Full Text Available The aim of this paper is estimation of Binary logistic regression parameters for maximizing the log-likelihood function with improved association indicators. In this paper the parameter estimation steps have been explained and then measures of association have been introduced and their calculations have been analyzed. Moreover a new related indicators based on membership degree level have been expressed. Indeed association measures demonstrate the number of success responses occurred in front of failure in certain number of Bernoulli independent experiments. In parameter estimation, existing indicators values is not sensitive to the parameter values, whereas the proposed indicators are sensitive to the estimated parameters during the iterative procedure. Therefore, proposing a new association indicator of binary logistic regression with more sensitivity to the estimated parameters in maximizing the log- likelihood in iterative procedure is innovation of this study.

  5. Reduction of coupling parameters and duality

    International Nuclear Information System (INIS)

    Oehme, R.; Max-Planck-Institut fuer Physik, Muenchen

    2000-01-01

    The general method of the reduction in the number of coupling parameters is discussed. Using renormalization group invariance, theories with several independent couplings are related to a set of theories with a single coupling parameter. The reduced theories may have particular symmetries, or they may not be related to any known symmetry. The method is more general than the imposition of invariance properties. Usually, there are only a few reduced theories with an asymptotic power series expansion corresponding to a renormalizable Lagrangian. There also exist 'general' solutions containing non-integer powers and sometimes logarithmic factors. As an example for the use of the reduction method, the dual magnetic theories associated with certain supersymmetric gauge theories are discussed. They have a superpotential with a Yukawa coupling parameter. This parameter is expressed as a function of the gauge coupling. Given some standard conditions, a unique, isolated power series solution of the reduction equations is obtained. After reparameterization, the Yukawa coupling is proportional to the square of the gauge coupling parameter. The coefficient is given explicitly in terms of the numbers of colors and flavors. 'General' solutions with non-integer powers are also discussed. A brief list is given of other applications of the reduction method. (orig.)

  6. Environmental hazards in Nepal: altitude illness, environmental exposures, injuries, and bites in travelers and expatriates.

    Science.gov (United States)

    Boggild, Andrea K; Costiniuk, Cecilia; Kain, Kevin C; Pandey, Prativa

    2007-01-01

    Adventure travel necessarily places travelers at risk of environmental hazards. We assessed the burden of "environmental" hazards among a cohort of travelers and expatriates presenting to a large travel clinic in Nepal. Data on travelers and expatriates seen at the Canadian International Water and Energy Consultants (CIWEC) clinic in Kathmandu were prospectively collected and entered into the GeoSentinel Surveillance Network database. Data on individuals receiving predefined diagnoses related to environmental hazards were extracted and analyzed. Of 10,499 travelers and 4,854 expatriates in the database, 2,160 were diagnosed with 2,533 environment-related illnesses. Injuries were common among both travelers and expatriates [N= 788 (6.1%) and 328 (4.9%), respectively], while altitude illness was seen almost exclusively in travelers [N= 611 (4.7%) vs N= 8 (0.1%)]. Factors independently associated with environmental diagnoses include male gender (p tourism (p educational impact in others.

  7. Relating masses and mixing angles. A model-independent model

    Energy Technology Data Exchange (ETDEWEB)

    Hollik, Wolfgang Gregor [DESY, Hamburg (Germany); Saldana-Salazar, Ulises Jesus [CINVESTAV (Mexico)

    2016-07-01

    In general, mixing angles and fermion masses are seen to be independent parameters of the Standard Model. However, exploiting the observed hierarchy in the masses, it is viable to construct the mixing matrices for both quarks and leptons in terms of the corresponding mass ratios only. A closer view on the symmetry properties leads to potential realizations of that approach in extensions of the Standard Model. We discuss the application in the context of flavored multi-Higgs models.

  8. A method for sensible heat flux model parameterization based on radiometric surface temperature and environmental factors without involving the parameter KB-1

    Science.gov (United States)

    Zhuang, Qifeng; Wu, Bingfang; Yan, Nana; Zhu, Weiwei; Xing, Qiang

    2016-05-01

    Sensible heat flux is a key component of land-atmosphere interaction. In most parameterizations it is calculated with surface-air temperature differences and total aerodynamic resistance to heat transfer (Rae) that is related to the KB-1 parameter. Suitable values are hard to obtain since KB-1 is related both to canopy characteristics and environmental conditions. In this paper, a parameterize method for sensible heat flux over vegetated surfaces (maize field and grass land in the Heihe river basin of northwest China) was proposed based on the radiometric surface temperature, surface resistance (Rs) and vapor pressures (saturated and actual) at the surface and the atmosphere above the canopy. A biophysics-based surface resistance model was revised to compute surface resistance with several environmental factors. The total aerodynamic resistance to heat transfer is directly calculated by combining the biophysics-based surface resistance and vapor pressures. One merit of this method is that the calculation of KB-1 can be avoided. The method provides a new way to estimate sensible heat flux over vegetated surfaces and its performance compares well to the LAS measured sensible heat and other empirical or semi-empirical KB-1 based estimations.

  9. Parameter motivated mutual correlation analysis: Application to the study of currency exchange rates based on intermittency parameter and Hurst exponent

    Science.gov (United States)

    Cristescu, Constantin P.; Stan, Cristina; Scarlat, Eugen I.; Minea, Teofil; Cristescu, Cristina M.

    2012-04-01

    We present a novel method for the parameter oriented analysis of mutual correlation between independent time series or between equivalent structures such as ordered data sets. The proposed method is based on the sliding window technique, defines a new type of correlation measure and can be applied to time series from all domains of science and technology, experimental or simulated. A specific parameter that can characterize the time series is computed for each window and a cross correlation analysis is carried out on the set of values obtained for the time series under investigation. We apply this method to the study of some currency daily exchange rates from the point of view of the Hurst exponent and the intermittency parameter. Interesting correlation relationships are revealed and a tentative crisis prediction is presented.

  10. 78 FR 58570 - Environmental Assessment; Entergy Nuclear Operations, Inc., Big Rock Point

    Science.gov (United States)

    2013-09-24

    ... Assessment; Entergy Nuclear Operations, Inc., Big Rock Point AGENCY: Nuclear Regulatory Commission. ACTION... applicant or the licensee), for the Big Rock Point (BRP) Independent Spent Fuel Storage Installation (ISFSI... Rock Point (BRP) Independent Spent Fuel Storage Installation (ISFSI). II. Environmental Assessment (EA...

  11. Polluting Production - Environmentally Sound Alternatives

    OpenAIRE

    Tamás Kocsis

    2002-01-01

    With the determination of principal parameters of producing and pollution abatement technologies, this paper quantifies abatement and external costs at the social optimum and analyses the dynamic relationship between technological development and the above-mentioned costs. With the partial analysis of parameters, the paper presents the impacts on the level of pollution and external costs of extensive and intensive environmental protection, market demand change and product fees, and not enviro...

  12. Applied dendroecology and environmental forensics. Characterizing and age dating environmental releases: fundamentals and case studies

    Science.gov (United States)

    Jean-Christophe Balouet; Gil Oudijk; Kevin T. Smith; Ioana Petrisor; Hakan Grudd; Bengt. Stocklassa

    2007-01-01

    Dendroecology, or the use of ring patterns to assess the age of trees and environmental factors controlling their growth, is a well-developed method in climatologic studies. This method holds great potential as a forensic tool for age dating, contamination assessment, and characterization of releases. Moreover, the method is independent of the physical presence of...

  13. Environmental monitoring at Olympic Dam

    International Nuclear Information System (INIS)

    Anon.

    1989-01-01

    The environmental management and protection program at the Olympic Dam uranium/copper/gold project, Roxby Downs, South Australia, monitors eight major environmental parameters - meteorology, vegetation, mine site rehabilitation, fauna, terrain, soil salinity, hydrogeology and well fields. It came into effect with the approval of the South Australian Government in March 1987. The Great Artesian Basin, one of the world's greatest artesian basins, is the source of the water supply for the project

  14. The strategic economic plan and the role of independent power in economic development

    International Nuclear Information System (INIS)

    House, D.

    1993-01-01

    Independent power production (IPP) in Newfoundland was examined within the context of the province's Strategic Economic Plan. Provisions of the Plan were summarized, with special reference to the promotion of alternative energy technologies and government efforts to amend regulations to facilitate development of alternative energy sources by independent producers. IPP was considered to be an ideal tool for regional economic development and diversification, assuming that environmental concerns were carefully considered and addressed. Some of the benefits ascribed to IPP included strengthening the private sector, creating new small business opportunities, improving competitiveness, promoting regional development, contributing to import substitution and enhance the province's technology and knowledge base

  15. Methodology for Evaluating Safety System Operability using Virtual Parameter Network

    International Nuclear Information System (INIS)

    Park, Sukyoung; Heo, Gyunyoung; Kim, Jung Taek; Kim, Tae Wan

    2014-01-01

    KAERI (Korea Atomic Energy Research Institute) and UTK (University of Tennessee Knoxville) are working on the I-NERI project to suggest complement of this problem. This research propose the methodology which provide the alternative signal in case of unable guaranteed reliability of some instrumentation with KAERI. Proposed methodology is assumed that several instrumentations are working normally under the power supply condition because we do not consider the instrumentation survivability itself. Thus, concept of the Virtual Parameter Network (VPN) is used to identify the associations between plant parameters. This paper is extended version of the paper which was submitted last KNS meeting by changing the methodology and adding the result of the case study. In previous research, we used Artificial Neural Network (ANN) inferential technique for estimation model but every time this model showed different estimate value due to random bias each time. Therefore Auto-Associative Kernel Regression (AAKR) model which have same number of inputs and outputs is used to estimate. Also the importance measures in the previous method depend on estimation model but importance measure of improved method independent on estimation model. Also importance index of previous method depended on estimation model but importance index of improved method is independent on estimation model. In this study, we proposed the methodology to identify the internal state of power plant when severe accident happens also it has been validated through case study. SBLOCA which has large contribution to severe accident is considered as initiating event and relationship amongst parameter has been identified. VPN has ability to identify that which parameter has to be observed and which parameter can be alternative to the missing parameter when some instruments are failed in severe accident. In this study we have identified through results that commonly number 2, 3, 4 parameter has high connectivity while

  16. Methodology for Evaluating Safety System Operability using Virtual Parameter Network

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sukyoung; Heo, Gyunyoung [Kyung Hee Univ., Yongin (Korea, Republic of); Kim, Jung Taek [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Tae Wan [Kepco International Nuclear Graduate School, Ulsan (Korea, Republic of)

    2014-05-15

    KAERI (Korea Atomic Energy Research Institute) and UTK (University of Tennessee Knoxville) are working on the I-NERI project to suggest complement of this problem. This research propose the methodology which provide the alternative signal in case of unable guaranteed reliability of some instrumentation with KAERI. Proposed methodology is assumed that several instrumentations are working normally under the power supply condition because we do not consider the instrumentation survivability itself. Thus, concept of the Virtual Parameter Network (VPN) is used to identify the associations between plant parameters. This paper is extended version of the paper which was submitted last KNS meeting by changing the methodology and adding the result of the case study. In previous research, we used Artificial Neural Network (ANN) inferential technique for estimation model but every time this model showed different estimate value due to random bias each time. Therefore Auto-Associative Kernel Regression (AAKR) model which have same number of inputs and outputs is used to estimate. Also the importance measures in the previous method depend on estimation model but importance measure of improved method independent on estimation model. Also importance index of previous method depended on estimation model but importance index of improved method is independent on estimation model. In this study, we proposed the methodology to identify the internal state of power plant when severe accident happens also it has been validated through case study. SBLOCA which has large contribution to severe accident is considered as initiating event and relationship amongst parameter has been identified. VPN has ability to identify that which parameter has to be observed and which parameter can be alternative to the missing parameter when some instruments are failed in severe accident. In this study we have identified through results that commonly number 2, 3, 4 parameter has high connectivity while

  17. Problems of low-parameter equations of state

    Science.gov (United States)

    Petrik, G. G.

    2017-11-01

    The paper focuses on the system approach to problems of low-parametric equations of state (EOS). It is a continuation of the investigations in the field of substantiated prognosis of properties on two levels, molecular and thermodynamic. Two sets of low-parameter EOS have been considered based on two very simple molecular-level models. The first one consists of EOS of van der Waals type (a modification of van der Waals EOS proposed for spheres). The main problem of these EOS is a weak connection with the micro-level, which raise many uncertainties. The second group of EOS has been derived by the author independently of the ideas of van der Waals based on the model of interacting point centers (IPC). All the parameters of the EOS have a meaning and are associated with the manifestation of attractive and repulsive forces. The relationship between them is found to be the control parameter of the thermodynamic level. In this case, EOS IPC passes into a one-parameter family. It is shown that many EOS of vdW-type can be included in the framework of the PC model. Simultaneously, all their parameters acquire a physical meaning.

  18. A consistent homogenization procedure to obtain few-group cell parameters

    International Nuclear Information System (INIS)

    Pierini, G.

    1979-01-01

    The criterion, according to which one heterogeneous and one homogeneous cell are equivalent if they have the same boundary values of both the flux and the normal components of the current, is used to homogenize radially an axially infinite cylindrical cell, with azimuth independent properties and moderatur adequately described by diffusion theory. The method, which leads to the definition of a full matrix of diffusion coefficients, provides a new and simple definition of the few-group cell parameters, which are nearly independent of the environment. (orig.) [de

  19. Sperm quality biomarkers complement reproductive and endocrine parameters in investigating environmental contaminants in common carp (Cyprinus carpio) from the Lake Mead National Recreation Area

    Science.gov (United States)

    Jenkins, Jill A.; Rosen, Michael R.; Dale, Rassa O.; Echols, Kathy R.; Torres, Leticia; Wieser, Carla M.; Kersten, Constance A.; Goodbred, Steven L.

    2018-01-01

    Lake Mead National Recreational Area (LMNRA) serves as critical habitat for several federally listed species and supplies water for municipal, domestic, and agricultural use in the Southwestern U.S. Contaminant sources and concentrations vary among the sub-basins within LMNRA. To investigate whether exposure to environmental contaminants is associated with alterations in male common carp (Cyprinus carpio) gamete quality and endocrine- and reproductive parameters, data were collected among sub-basins over 7 years (1999–2006). Endpoints included sperm quality parameters of motility, viability, mitochondrial membrane potential, count, morphology, and DNA fragmentation; plasma components were vitellogenin (VTG), 17ß-estradiol, 11-keto-testosterone, triiodothyronine, and thyroxine. Fish condition factor, gonadosomatic index, and gonadal histology parameters were also measured. Diminished biomarker effects were noted in 2006, and sub-basin differences were indicated by the irregular occurrences of contaminants and by several associations between chemicals (e.g., polychlorinated biphenyls, hexachlorobenzene, galaxolide, and methyl triclosan) and biomarkers (e.g., plasma thyroxine, sperm motility and DNA fragmentation). By 2006, sex steroid hormone and VTG levels decreased with subsequent reduced endocrine disrupting effects. The sperm quality bioassays developed and applied with carp complemented endocrine and reproductive data, and can be adapted for use with other species.

  20. Effect of Medium Symmetries in Limiting the Number of Parameters Estimated with Polarimetric Interferometry

    Science.gov (United States)

    Moghaddam, Mahta

    2000-01-01

    The addition of interferometric backscattering pairs to the conventional polarimetric SAR data over forests and other vegetated areas increases the dimensionality of the data space, in principle enabling the estimation of a larger number of vegetation parameters. Without regard to the sensitivity of these data to vegetation scattering parameters, this paper poses the question: Will increasing the data channels as such result in a one-to-one increase in the number of parameters that can be estimated, or do vegetation and data properties inherently limit that number otherwise? In this paper, the complete polarimetric interferometric covariance matrix is considered and various symmetry properties of the scattering medium are used to study whether any of the correlation pairs can be eliminated. The number of independent pairs has direct consequences in their utility in parameter estimation schemes, since the maximum number of parameters that can be estimated cannot exceed the number of unique measurements. The independent components of the polarimetric interferometric SAR (POL/INSAR) data are derived for media with reflection, rotation, and azimuth symmetries, which are often encountered in vegetated surfaces. Similar derivations have been carried out before for simple polarimetry, i.e., zero baseline. This paper extends those to the interferometric case of general nonzero baselines. It is shown that depending on the type of symmetries present, the number of independent available measurements that can be used to estimate medium parameters will vary. In particular, whereas in the general case there are 27 mathematically independent measurements possible from a polarimetric interferometer, this number can be reduced to 15, 9, and 6 if the medium has reflection, rotation, or azimuthal symmetries, respectively. The results can be used in several ways in the interpretation of SAR data and the development of parameter estimation schemes, which will be discussed at the

  1. Radioisotope albumin flux measurement of microvascular lung permeability: an independent parameter in acute respiratory failure?

    International Nuclear Information System (INIS)

    Hoegerle, S.; Nitzsche, E.U.; Reinhardt, M.J.; Moser, E.; Benzing, A.; Geiger, K.; Schulte Moenting, J.

    2001-01-01

    Aim: To evaluate the extent to which single measurements of microvascular lung permeability may be relevant as an additional parameter in a heterogenous clinical patient collective with Acute Lung Injury (ALI) and Acute Respiratory Distress Syndrome (ARDS). Methods: In 36 patients with pneumonia (13), non pneumogenic sepsis (9) or trauma (14) meeting the consensus conference criteria of ALI or ARDS double-isotope protein flux measurements ( 51 Cr erythrocytes as intravascular tracer, Tc-99m human albumin as diffusible tracer) of microvascular lung permeability were performed using the Normalized Slope Index (NSI). The examination was to determine whether there is a relationship between the clinical diagnosis of ALI/ARDS, impaired permeability and clinical parameters, that is the underlying disease, oxygenation, duration of mechanical ventilation and mean pulmonary-artery pressure (PAP). Results: At the time of study, 25 patients presented with increased permeability (NSI > 1 x 10 -3 min -1 ) indicating an exudative stage of disease, and 11 patients with normal permeability. The permeability impairment correlated with the underlying disease (p > 0.05). With respect to survival, there was a negative correlation to PAP (p [de

  2. Environmental monitoring by means of remote sensing

    International Nuclear Information System (INIS)

    Theilen-Willige, B.

    1993-01-01

    Aircraft and satellite aerial photographs represent indispensible tools for environmental observation today. They contribute to a systematic inventory of important environmental parameters such as climate, vegetation or surface water. Their great importance lies in the continuous monitoring of large regions so that changes in environmental conditions are quickly detected. This book provides an overview of the capabilities of remote sensing in environmental monitoring and in the recognition of environmental problems as well as of the usefulness of remote sensing data for environmental planning. Also addressed is the role of remote sensing in the monitoring of natural hazards such as earthquakes and volcano eruptions as well as problems of remote sensing technology transfer to developing countries. (orig.) [de

  3. The evaluation of set of criticality parameters using scale system

    International Nuclear Information System (INIS)

    Abe, Alfredo; Sanchez, Andrea; Yamaguchi, Mistuo

    2009-01-01

    In evaluating the criticality safety of the nuclear fuel facility, it is important to apply a consistent methodology, which consider every aspects concerning various types of criticality parameters. Usually, the critical parameters are compiled and arranged into handbooks, and these handbooks are based on experience with nuclear facilities, experimental data from criticality safety research facilities, and theoretical studies performed using numerical simulations. Most of criticality safety evaluation can be addressed using the criticality parameters data directly from handbook, but some critical parameters for a specific chemical mixtures and/or enrichment are not be available. Consequently, not available parameters has to be evaluated. This work present the methodology to evaluate a set of critical parameters using SCALE system for various types of mixtures present at nuclear fuel cycle facilities for two different level of enrichment, the results are verified in the independent calculation using MCNP Monte Carlo Code. (author)

  4. Conceptual design of independently tunable cells RF gun with external injecting structure

    International Nuclear Information System (INIS)

    Liang Junjun; Feng Guangyao; Pei Yuanji; Pang Jian

    2012-01-01

    To obtain the micro-pulse bunch with the order of hundred femtoseconds length and high repetition rate, the pa- per proposes the independently tunable cells (ITC) RF gun, which has a double-cell structure with the cells being power fed independently. By choosing appropriate feeding power and phase of the two cells, this ITC-RF gun can achieve bunches of excellent characteristics. Additionally, the application of a-magnet and laser system can be avoided, which leads to more compact layout. An external injecting ITC-RF gun (DC-ITC-RF gun) structure is designed accordingly. The external injecting structure can increase beam current, decrease energy spread, and cancel the back-bombardment effect almost completely. By means of 1-D and 3- D beam dynamics calculation with different structure parameters, a group of RF parameters are obtained for better beam characteristics. Then the paper designs a pre-injector so that particles can be accelerated to 10 MeV. By choosing appropriate feeding power and incident particle phase for the pre-injector, the bunch length can be further compressed. (authors)

  5. New properties of z-scaling: flavor independence and saturation at low z

    International Nuclear Information System (INIS)

    Zborovsky, I.; Tokarev, M.V.

    2008-01-01

    Experimental ISR, RHIC, and Tevatron data on inclusive cross sections of particles produced in high energy proton-(anti)proton collisions are analyzed in the framework of z-scaling. New features of the scaling function ψ(z) are established. These are flavor independence of ψ(z) including particles with heavy flavor content and saturation at low z. Flavor independence means that the shape of the scaling function ψ(z) is the same for different hadron species. Saturation corresponds to flattering of ψ(z) for low z < 0.1. Relations of model parameters used in data z-presentation with some thermodynamical quantities (entropy, specific heat, temperature) are discussed. It is shown that behavior of particle spectra at low z is controlled by a parameter c interpreted as specific heat of the created medium associated with production of the inclusive particle. The saturation regime of ψ(z) observed at low z is assumed to be preferable in searching for phase transitions of hadron matter and for study of nonperturbative QCD in high energy proton-(anti)proton collisions at U70, RHIC, Tevatron, and LHC

  6. Thermodynamics of two-parameter quantum group Bose and Fermi gases

    International Nuclear Information System (INIS)

    Algin, A.

    2005-01-01

    The high and low temperature thermodynamic properties of the two-parameter deformed quantum group Bose and Fermi gases with SU p/q (2) symmetry are studied. Starting with a SU p/q (2)-invariant bosonic as well as fermionic Hamiltonian, several thermodynamic functions of the system such as the average number of particles, internal energy and equation of state are derived. The effects of two real independent deformation parameters p and q on the properties of the systems are discussed. Particular emphasis is given to a discussion of the Bose-Einstein condensation phenomenon for the two-parameter deformed quantum group Bose gas. The results are also compared with earlier undeformed and one-parameter deformed versions of Bose and Fermi gas models. (author)

  7. Environmental labelling of electricity delivery contracts in Sweden

    International Nuclear Information System (INIS)

    Kaaberger, Tomas

    2003-01-01

    Competition in the electricity market allows customers to choose between suppliers. As a consequence, customers may demand electricity from specified sources of energy. In Sweden, the Swedish Society for Nature Conservation (SSNC), operates a system of environmental labelling of electricity delivery contracts since 1996. Labelling is available for suppliers offering electricity from renewable sources of energy with some additional criteria. Companies may acquire a licence to use the label by showing ability to deliver such electricity and by agreeing to be audited. The system is private independent. It is operating on the bases of credibility earned by the SSNC during 90 years as an environmental organisation and 10 years as operator of environmental labelling of consumer products. The system is market oriented, compatible with WTO and EU market principles, and independent of governmental environmental restrictions, subsidy or quota systems. It is relying on voluntary agreements. The results are desirable if only a few by electricity under labelled contracts as well as if every customer do so. The market is growing. A majority of the suppliers have a license and may offer labelled contracts. In the year 2000, 7% of all electricity sold to final consumers was sold under labelled contracts

  8. Dependences of Ultrasonic Parameters for Osteoporosis Diagnosis on Bone Mineral Density

    International Nuclear Information System (INIS)

    Hwang, Kyo Seung; Kim, Yoon Mi; Park, Jong Chan; Choi, Min Joo; Lee, Kang Il

    2012-01-01

    Quantitative ultrasound technologies for osteoporosis diagnosis measure ultrasonic parameters such as speed of sound(SOS) and normalized broadband ultrasound attenuation(nBUA) in the calcaneus (heel bone). In the present study, the dependences of SOS and nBUA on bone mineral density in the proximal femur with high risk of fracture were investigated by using 20 trabecular bone samples extracted from bovine femurs. SOS and nBUA in the femoral trabecular bone samples were measured by using a transverse transmission method with one matched pair of ultrasonic transducers with a center frequency of 1.0 MHz. SOS and nBUA measured in the 20 trabecular bone samples exhibited high Pearson's correlation coefficients (r) of r = 0.83 and 0.72 with apparent bone density, respectively. The multiple regression analysis with SOS and nBUA as independent variables and apparent bone density as a dependent variable showed that the correlation coefficient r = 0.85 of the multiple linear regression model was higher than those of the simple linear regression model with either parameter SOS or nBUA as an independent variable. These high linear correlations between the ultrasonic parameters and the bone density suggest that the ultrasonic parameters measured in the femur can be useful for predicting the femoral bone mineral density.

  9. Measurement of agricultural parameters using wireless sensor network (WSN)

    Science.gov (United States)

    Guaña-Moya, Javier; Sánchez-Almeida, Tarquino; Salgado-Reyes, Nelson

    2018-04-01

    The technological advances have allowed to create new applications in telecommunications, applying low power and reduced costs in their equipment, thus achieving the evolution of new wireless networks or also denominated Wireless Sensor Network. These technologies allow the generation of measurements and analysis of environmental parameter data and soil. Precision agriculture requires parameters for the improvement of production, obtained through WSN technologies. This research analyzes the climatic requirements and soil parameters in a rose plantation in a greenhouse at an altitude of 3,100 meters above sea level. In the present investigation, maximum parameters were obtained in the production of roses, which are in the optimum range of production, whereas the minimum parameters of temperature, humidity and luminosity, evidenced that these parameters can damage the plants, since temperatures less than 10 °C slow down the growth of the plant and allow the proliferation of diseases and fungi.

  10. Psychophysical parameters of a multidimensional pain scale in newborns

    International Nuclear Information System (INIS)

    De Oliveira, M V M; De Jesus, J A L; Tristao, R M

    2012-01-01

    The Premature Infant Pain Profile (PIPP) is a promising multidimensional tool for comparison and testing of new technologies in newborn pain assessment studies since it may adhere to basic psychophysical parameters of intensity, direction, reactivity, regulation and slope described in analyses of physiological pain indicators. The aim of this study was to evaluate whether these psychophysical parameters can be achieved using the PIPP in acute pain assessment. Thirty-six healthy term newborn infants were conveniently sampled whilst being videotaped before, during and after heel prick blood sampling. The images were blind-scored by three trained independent raters and scored against the PIPP. The PIPP and its facial action indicators met the parameters of intensity, reactivity and regulation (all p < 0.001). The heart rate variability did not meet any parameter (all p > 0.05). The oxygen saturation variability met only the intensity parameter (p < 0.05). The behavioural state indicator met all parameters and had the best correlation to the psychophysical parameters of all indicators of PIPP (all p < 0.001). We concluded that the overall PIPP meets the assumptions of these psychophysical parameters, being the behavioural state indicator which best fit the model. (paper)

  11. Methodology and parameters for assessing human health effects for waste sites at the Savannah River Plant: Environmental information document

    International Nuclear Information System (INIS)

    King, C.M.; Marter, W.L.; Looney, B.B.; Pickett, J.B.

    1987-03-01

    This report provides a summary of the components of risk assessment and presents the technical basis for application of the risk evaluation process to the principal pollutants at SRP: radionuclides, toxic chemicals, and carcinogenic compounds. An extensive technical data base from the fields of radiation health physics, toxicology, and environmental sciences is required to accomplish this task. The origin and meaning of this data base is summarized for each class of contaminant and parameter values provided for use in numerical analysis of risk. The process of risk assessment is associated with uncertainties, a fact which is frequently stated in the technical literature addressing this subject. A review of risk assessment uncertainties and the limitations of predictive risk assessment are summarized. Risk estimators for each class of contaminants at the SRP have been tabulated for radionuclides, toxic chemicals, and carcinogens from the technical literature. Estimation of human health risk is not an additive process for radiation effects and chemical carcinogenesis since their respective dosimetric models are distinctly different even though the induction of cancer is reported to be the common end result. It is recommended in this report that risk estimation for radionuclides and chemical carcinogens should be tabulated separately and this recommendation has been applied in all environmental information documentation published by the Savannah River Laboratory. Impacts due to toxic chemicals in the biosphere should also be estimated as a separate entity since toxic chemical risk estimators are uniquely different and do not reflect the probability of a detrimental health effect. 23 refs., 4 figs., 13 tabs

  12. Risk perceptions, general environmental beliefs, and willingness to address climate change

    International Nuclear Information System (INIS)

    O'Connor, R.E.; Bord, R.J.; Fisher, A.

    1999-01-01

    The research reported here examines the relationship between risk perceptions and willingness to address climate change. The data are a national sample of 1,225 mail surveys that include measures of risk perceptions and knowledge tied to climate change, support for voluntary and government actions to address the problem, general environmental beliefs, and demographic variables. Risk perceptions matter in predicting behavior intentions. Risk perceptions are not a surrogate for general environmental beliefs, but have their own power to account for behavioral intentions. There are four secondary conclusions. First, behavioral intentions regarding climate change are complex and intriguing. People are neither nonbelievers who will take no initiatives themselves and oppose all government efforts, nor are they believers who promise both to make personal efforts and to vote for every government proposal that promises to address climate change. Second, there are separate demographic sources for voluntary actions compared with voting intentions. Third, recognizing the causes of global warming is a powerful predictor of behavioral intentions independent from believing that climate change will happen and have bad consequences. Finally, the success of the risk perception variables to account for behavioral intentions should encourage greater attention to risk perceptions as independent variables. Risk perceptions and knowledge, however, share the stage with general environmental beliefs and demographic characteristics. Although related, risk perceptions, knowledge, and general environmental beliefs are somewhat independent predictors of behavioral intentions

  13. Study design considerations in evaluating environmental impacts

    Science.gov (United States)

    Stan T. Lebow; Paul A. Cooper; Patricia Lebow

    2006-01-01

    The purpose of this chapter is to make the reader aware of how choices in study parameters may influence the outcome of treated-wood environmental impact evaluations. Evaluation of the leaching and environmental accumulation of preservatives from treated wood is a complex process. and many factors can influence the results of such studies. In laboratory studies, the...

  14. Preoperative carcinoembryonic antigen and prognosis of colorectal cancer. An independent prognostic factor still reliable.

    Science.gov (United States)

    Li Destri, Giovanni; Rubino, Antonio Salvatore; Latino, Rosalia; Giannone, Fabio; Lanteri, Raffaele; Scilletta, Beniamino; Di Cataldo, Antonio

    2015-04-01

    To evaluate whether, in a sample of patients radically treated for colorectal carcinoma, the preoperative determination of the carcinoembryonic antigen (p-CEA) may have a prognostic value and constitute an independent risk factor in relation to disease-free survival. The preoperative CEA seems to be related both to the staging of colorectal neoplasia and to the patient's prognosis, although this-to date-has not been conclusively demonstrated and is still a matter of intense debate in the scientific community. This is a retrospective analysis of prospectively collected data. A total of 395 patients were radically treated for colorectal carcinoma. The preoperative CEA was statistically compared with the 2010 American Joint Committee on Cancer (AJCC) staging, the T and N parameters, and grading. All parameters recorded in our database were tested for an association with disease-free survival (DFS). Only factors significantly associated (P < 0.05) with the DFS were used to build multivariate stepwise forward logistic regression models to establish their independent predictors. A statistically significant relationship was found between p-CEA and tumor staging (P < 0.001), T (P < 0.001) and N parameters (P = 0.006). In a multivariate analysis, the independent prognostic factors found were: p-CEA, stages N1 and N2 according to AJCC, and G3 grading (grade). A statistically significant difference (P < 0.001) was evident between the DFS of patients with normal and high p-CEA levels. Preoperative CEA makes a pre-operative selection possible of those patients for whom it is likely to be able to predict a more advanced staging.

  15. Environmental vs Demographic Stochasticity in Population Growth

    OpenAIRE

    Braumann, C. A.

    2010-01-01

    Compares the effect on population growth of envinonmental stochasticity (random environmental variations described by stochastic differential equations) with demographic stochasticity (random variations in births and deaths described by branching processes and birth-and-death processes), in the density-independent and the density-dependent cases.

  16. Metagenomic covariation along densely sampled environmental gradients in the Red Sea

    KAUST Repository

    Thompson, Luke R

    2016-07-15

    Oceanic microbial diversity covaries with physicochemical parameters. Temperature, for example, explains approximately half of global variation in surface taxonomic abundance. It is unknown, however, whether covariation patterns hold over narrower parameter gradients and spatial scales, and extending to mesopelagic depths. We collected and sequenced 45 epipelagic and mesopelagic microbial metagenomes on a meridional transect through the eastern Red Sea. We asked which environmental parameters explain the most variation in relative abundances of taxonomic groups, gene ortholog groups, and pathways—at a spatial scale of <2000 km, along narrow but well-defined latitudinal and depth-dependent gradients. We also asked how microbes are adapted to gradients and extremes in irradiance, temperature, salinity, and nutrients, examining the responses of individual gene ortholog groups to these parameters. Functional and taxonomic metrics were equally well explained (75–79%) by environmental parameters. However, only functional and not taxonomic covariation patterns were conserved when comparing with an intruding water mass with different physicochemical properties. Temperature explained the most variation in each metric, followed by nitrate, chlorophyll, phosphate, and salinity. That nitrate explained more variation than phosphate suggested nitrogen limitation, consistent with low surface N:P ratios. Covariation of gene ortholog groups with environmental parameters revealed patterns of functional adaptation to the challenging Red Sea environment: high irradiance, temperature, salinity, and low nutrients. Nutrient-acquisition gene ortholog groups were anti-correlated with concentrations of their respective nutrient species, recapturing trends previously observed across much larger distances and environmental gradients. This dataset of metagenomic covariation along densely sampled environmental gradients includes online data exploration supplements, serving as a community

  17. Determination of 13C CSA Tensors: Extension of the Model-independent Approach to an RNA Kissing Complex Undergoing Anisotropic Rotational Diffusion in Solution

    International Nuclear Information System (INIS)

    Ravindranathan, Sapna; Kim, Chul-Hyun; Bodenhausen, Geoffrey

    2005-01-01

    Chemical shift anisotropy (CSA) tensor parameters have been determined for the protonated carbons of the purine bases in an RNA kissing complex in solution by extending the model-independent approach [Fushman, D., Cowburn, D. (1998) J. Am. Chem. Soc. 120, 7109-7110]. A strategy for determining CSA tensor parameters of heteronuclei in isolated X-H two-spin systems (X = 13 C or 15 N) in molecules undergoing anisotropic rotational diffusion is presented. The original method relies on the fact that the ratio κ 2 =R 2 auto /R 2 cross of the transverse auto- and cross-correlated relaxation rates involving the X CSA and the X-H dipolar interaction is independent of parameters related to molecular motion, provided rotational diffusion is isotropic. However, if the overall motion is anisotropic κ 2 depends on the anisotropy D parallel /D -perpendicular of rotational diffusion. In this paper, the field dependence of both κ 2 and its longitudinal counterpart κ 1 =R 1 auto /R 1 cross are determined. For anisotropic rotational diffusion, our calculations show that the average κ av = 1/2 (κ 1 +κ 2 ), of the ratios is largely independent of the anisotropy parameter D parallel /D -perpendicular . The field dependence of the average ratio κ av may thus be utilized to determine CSA tensor parameters by a generalized model-independent approach in the case of molecules with an overall motion described by an axially symmetric rotational diffusion tensor

  18. Waterborne Electrospinning of Poly(N-isopropylacrylamide) by Control of Environmental Parameters.

    Science.gov (United States)

    Schoolaert, Ella; Ryckx, Paulien; Geltmeyer, Jozefien; Maji, Samarendra; Van Steenberge, Paul H M; D'hooge, Dagmar R; Hoogenboom, Richard; De Clerck, Karen

    2017-07-19

    With increasing toxicity and environmental concerns, electrospinning from water, i.e., waterborne electrospinning, is crucial to further exploit the resulting nanofiber potential. Most water-soluble polymers have the inherent limitation of resulting in water-soluble nanofibers, and a tedious chemical cross-linking step is required to reach stable nanofibers. An interesting alternative route is the use of thermoresponsive polymers, such as poly(N-isopropylacrylamide) (PNIPAM), as they are water-soluble beneath their lower critical solution temperature (LCST) allowing low-temperature electrospinning while the obtained nanofibers are water-stable above the LCST. Moreover, PNIPAM nanofibers show major potential to many application fields, including biomedicine, as they combine the well-known on-off switching behavior of PNIPAM, thanks to its LCST, with the unique properties of nanofibers. In the present work, based on dedicated turbidity and rheological measurements, optimal combinations of polymer concentration, environmental temperature, and relative humidity are identified allowing, for the first time, the production of continuous, bead-free PNIPAM nanofibers electrospun from water. More specifically, PNIPAM gelation was found to occur well below its LCST at higher polymer concentrations leading to a temperature regime where the viscosity significantly increases without compromising the polymer solubility. This opens up the ecological, water-based production of uniform PNIPAM nanofibers that are stable in water at temperatures above PNIPAM's LCST, making them suitable for various applications, including drug delivery and switchable cell culture substrates.

  19. Independent technical review of Savannah River Site Defense Waste Processing Facility technical issues

    International Nuclear Information System (INIS)

    1992-07-01

    The Savannah River Site (SRS) Defense Waste Processing Facility (DWPF) will vitrify high-level radioactive waste that is presently stored as liquid, salt-cake, and sludge in 51 waste-storage tanks. Construction of the DWPF began in 1984, and the Westinghouse Savannah Company (WSRC) considers the plant to be 100% turned over from construction and 91% complete. Cold-chemical runs are scheduled to begin in November 1992, and hot start up is projected for June 1994. It is estimated that the plant lifetime must exceed 15 years to complete the vitrification of the current, high-level tank waste. In a memo to the Assistant Secretary for Defense Programs (DP-1), the Assistant Secretary for Environmental Restoration and Waste management (EM-1) established the need for an Independent Technical Review (ITR), or the Red Team, to ''review process technology issues preventing start up of the DWPF.'' This report documents the findings of an Independent Technical Review (ITR) conducted by the Department of Energy (DOE), Office of Environmental Restoration and Waste Management (EM), at the request of the Assistant Secretary for Environmental Restoration and Waste Management, of specified aspects of Defense Waste Process Facility (DWPF) process technology. Information for the assessment was drawn from documents provided to the ITR Team by the Westinghouse Savannah River Company (WSRC), and presentations, discussions, interviews, and tours held at the Savannah River Site (SRS) during the weeks of February and March 9, 1992

  20. Independence and Product Systems

    OpenAIRE

    Skeide, Michael

    2003-01-01

    Starting from elementary considerations about independence and Markov processes in classical probability we arrive at the new concept of conditional monotone independence (or operator-valued monotone independence). With the help of product systems of Hilbert modules we show that monotone conditional independence arises naturally in dilation theory.

  1. Estimating relations between temperature, relative humidity as independed variables and selected water quality parameters in Lake Manzala, Egypt

    Directory of Open Access Journals (Sweden)

    Gehan A.H. Sallam

    2018-03-01

    Full Text Available In Egypt, Lake Manzala is the largest and the most productive lake of northern coastal lakes. In this study, the continuous measurements data of the Real Time Water Quality Monitoring stations in Lake Manzala were statistically analyzed to measure the regional and seasonal variations of the selected water quality parameters in relation to the change of air temperature and relative humidity. Simple formulas are elaborated using the DataFit software to predict the selected water quality parameters of the Lake including pH, Dissolved Oxygen (DO, Electrical Conductivity (EC, Total Dissolved Solids (TDS, Turbidity, and Chlorophyll as a function of air temperature, relative humidity and quantities and qualities of the drainage water that discharge into the lake. An empirical positive relation was found between air temperature and the relative humidity and pH, EC and TDS and negative relation with DO. There is no significant effect on the other two parameters of turbidity and chlorophyll.

  2. Setting parameters in the cold chain

    Directory of Open Access Journals (Sweden)

    Victoria Rodríguez

    2011-12-01

    Full Text Available Breaks in the cold chain are important economic losses in food and pharmaceutical companies. Many of the failures in the cold chain are due to improper adjustment of equipment parameters such as setting the parameters for theoretical conditions, without a corresponding check in normal operation. The companies that transport refrigeratedproducts must be able to adjust the parameters of the equipment in an easy and quick to adapt their functioning to changing environmental conditions. This article presents the results of a study carried out with a food distribution company. The main objective of the study is to verify the effectiveness of Six Sigma as a methodological toolto adjust the equipment in the cold chain. The second objective is more speciÞ c and is to study the impact of: reducing the volume of storage in the truck, the initial temperature of the storage areain the truck and the frequency of defrost in the transport of refrigerated products.

  3. On model-independent analyses of elastic hadron scattering

    International Nuclear Information System (INIS)

    Avila, R.F.; Campos, S.D.; Menon, M.J.; Montanha, J.

    2007-01-01

    By means of an almost model-independent parametrization for the elastic hadron-hadron amplitude, as a function of the energy and the momentum transfer, we obtain good descriptions of the physical quantities that characterize elastic proton-proton and antiproton-proton scattering (total cross section, r parameter and differential cross section). The parametrization is inferred on empirical grounds and selected according to high energy theorems and limits from axiomatic quantum field theory. Based on the predictive character of the approach we present predictions for the above physical quantities at the Brookhaven RHIC, Fermilab Tevatron and CERN LHC energies. (author)

  4. Design of Parameter Independent, High Performance Sensorless Controllers for Permanent Magnet Synchronous Machines

    DEFF Research Database (Denmark)

    Xie, Ge

    . The transient fluctuation of the estimated rotor position error is around 20 degrees with a step load torque change from 0% to 100% of the rated torque. The position error in steady state is within ±2 electrical degrees for the best case. The proposed method may also be used for e.g. online machine parameter......The Permanent Magnet Synchronous Machine (PMSM) has become an attractive candidate for various industrial applications due to its high efficiency and torque density. In the PMSM drive system, simple and robust control methods play an important role in achieving satisfactory drive performances....... For reducing the cost and increasing the reliability of the drive system, eliminating the mechanical sensor brings a lot advantages to the PMSM drive system. Therefore, sensorless control was developed and has been increasingly used in different PMSM drive systems in the last 20 years. However, machine...

  5. An independent board of directors and corporate sustainability: A South African and Nigerian perspective

    Directory of Open Access Journals (Sweden)

    Collins C Ngwakwe

    2014-03-01

    Full Text Available This paper examined the stance of independent directors on corporate sustainable development initiative in South Africa and Nigeria. This has become apposite considering the role of independent directors in corporate strategic decisions and performance. It is believed that independent boards strive to direct corporate decisions to protect the investors and thus improve financial performance. Given that sustainability initiative is currently occupying a vital strategic position in protecting firms against inherent and imminent climate change and financial risks, the paper undertakes a survey of South African and Nigerian companies to ascertain the role of independent directors on corporate sustainable development initiatives. Using a mix method of primary and secondary data analysis, the paper finds that independent boards in both countries of study understand the importance of sustainability; however a pragmatic stance on sustainability is more visible in South Africa where independent boards are members of and/or participate in nominating corporate sustainability committees. The paper suggests the need for improved detailed disclosure on sustainability in the Nigerian corporate annual reports; the Nigerian Stock Exchange may boost this initiative by establishing a social and environmental reporting index supported by an annual survey of company sustainability disclosure. It also suggests the need to include sustainability awareness and interest in the metrics that are used in the appointment of independent boards in Nigerian companies.

  6. Model-independent particle accelerator tuning

    Directory of Open Access Journals (Sweden)

    Alexander Scheinker

    2013-10-01

    Full Text Available We present a new model-independent dynamic feedback technique, rotation rate tuning, for automatically and simultaneously tuning coupled components of uncertain, complex systems. The main advantages of the method are: (1 it has the ability to handle unknown, time-varying systems, (2 it gives known bounds on parameter update rates, (3 we give an analytic proof of its convergence and its stability, and (4 it has a simple digital implementation through a control system such as the experimental physics and industrial control system (EPICS. Because this technique is model independent it may be useful as a real-time, in-hardware, feedback-based optimization scheme for uncertain and time-varying systems. In particular, it is robust enough to handle uncertainty due to coupling, thermal cycling, misalignments, and manufacturing imperfections. As a result, it may be used as a fine-tuning supplement for existing accelerator tuning/control schemes. We present multiparticle simulation results demonstrating the scheme’s ability to simultaneously adaptively adjust the set points of 22 quadrupole magnets and two rf buncher cavities in the Los Alamos Neutron Science Center (LANSCE Linear Accelerator’s transport region, while the beam properties and rf phase shift are continuously varying. The tuning is based only on beam current readings, without knowledge of particle dynamics. We also present an outline of how to implement this general scheme in software for optimization, and in hardware for feedback-based control/tuning, for a wide range of systems.

  7. Handbook of parameter values for the prediction of radionuclide transfer in temperate environments

    International Nuclear Information System (INIS)

    1994-01-01

    This Handbook has been prepared in response to a widely expressed interest in having a convenient and authoritative reference for radionuclide transfer parameter values used in biospheric assessment models. It draws on data from North America and Europe, much of which was collected through projects of the International Union of Radioecologists (IUR) and the Commission of European Communities (CEC) over the last decade. It is intended to supplement existing IAEA publications on environmental assessment methodology, primarily Generic Models and Parameters for Assessing the Environmental Transfer of Radionuclides from Routine Releases, IAEA Safety Series No. 57 (1982). 219 refs, 3 figs, 32 tabs

  8. Dependence of the conservation status of acid grasslands at the Pohorje and Kozjak on socioeconomic parameters

    Directory of Open Access Journals (Sweden)

    Karmen KETIŠ

    2015-12-01

    Full Text Available Grassland habitats were studied on twenty farms on the area of the Radlje ob Dravi administration unit, in the transect from Kozjak to Pohorje at different altitudes. The aim of the study was to investigate how environmental and  socio-economic parameters influence the diversity of plant species and, consequently, the conservation of grassland on acid soils, which are rare in Slovenia and are therefore more protected. The socioeconomic structure of farms was studied on the basis of an inquiry carried out on farms. Part-time farms prevail; the average age of farmers is 56.5 years, and 30% of farmers has no education or just elementary school. The relationship among the environmental, socio-economic parameters and floristic structures of grasslands was studied using canonic-correspondence analysis. The impact of 16 parameters was analysed, of which six were determined not to be statistically significant. The occurrence of chosen plant species was analysed in relation to environmental and socioeconomic parameters. The efficiency of agro-environmental subsidies in relation to plant species diversity was evaluated. It was determined that the education and age of farmers influence the intensity of farming and consequently have an impact on the diversity of plants species and the conservation status of grasslands.

  9. Towards scale-independent land-surface flux estimates in Noah-MP

    Science.gov (United States)

    Thober, Stephan; Mizukami, Naoki; Samaniego, Luis; Attinger, Sabine; Clark, Martyn; Cuntz, Matthias

    2017-04-01

    Land-surface models use a variety of process representations to calculate terrestrial energy, water and biogeochemical fluxes. These process descriptions are usually derived from point measurements which are, in turn, scaled to much larger resolutions ranging from 1 km in catchment hydrology to 100 km in climate modelling. Both, hydrologic and climate models are nowadays run on different spatial resolutions, using the exactly same land surface representations. A fundamental criterion for the physical consistency of land-surface simulations across scales is that a flux estimated over a given area is independent of the spatial model resolution (i.e., the flux-matching criterion). The Noah-MP land surface model considers only one soil and land cover type per model grid cell without any representation of their subgrid variability, implying a weak flux-matching. A fractional approach simulates the subgrid variability but it requires a higher computational demand than using effective parameters and it is used only for land cover in current land surface schemes. A promising approach to derive scale-independent parameters is the Multiscale Parameter Regionalization (MPR) technique, which consists of two steps: first, it applies transfer functions directly to high-resolution data (such as 100 m soil maps) to derive high-resolution model parameter fields, acknowledging the full subgrid variability. Second, it upscales these high-resolution parameter fields to the model resolution by using appropriate upscaling operators. MPR has shown to improve substantially the scalability of the mesoscale Hydrologic Models mHM (Samaniego et al., 2010 WRR). Here, we apply the MPR technique to the Noah-MP land-surface model for a large sample of basins distributed across the contiguous USA. Specifically, we evaluate the flux-matching criterion for several hydrologic fluxes such as evapotranspiration and drainage at scales ranging from 3 km to 48 km. We investigate the impact of different

  10. Review and analysis of parameters for assessing transport of environmentally released radionuclides through agriculture

    International Nuclear Information System (INIS)

    Baes, C.F. III; Sharp, R.D.; Sjoreen, A.L.; Shor, R.W.

    1984-09-01

    Most of the default parameters incorporated into the TERRA computer code are documented including a literature review and systematic analysis of element-specific transfer parameters B/sub v/, B/sub r/, F/sub m/, F/sub f/, and K/sub d/. This review and analysis suggests default values which are consistent with the modeling approaches taken in TERRA and may be acceptable for most assessment applications of the computer code. However, particular applications of the code and additional analysis of elemental transport may require alternative default values. Use of the values reported herein in other computer codes simulating terrestrial transport is not advised without careful interpretation of the limitations and scope these analyses. An approach to determination of vegetation-specific interception fractions is also discussed. The limitations of this approach are many, and its use indicates the need for analysis of deposition, interception, and weathering processes. Judgement must be exercised in interpretation of plant surface concentrations generated. Finally, the location-specific agricultural, climatological, and population parameters in the default SITE data base documented. These parameters are intended as alternatives to average values currently used. Indeed, areas in the United States where intensive crop, milk, or beef production occurs will be reflected in the parameter values as will areas where little agricultural activity occurs. However, the original information sources contained some small error and the interpolation and conversion methods used will add more. Parameters used in TERRA not discussed herein are discussed in the companion report to this one - ORNL-5785. In the companion report the models employed in and the coding of TERRA are discussed. These reports together provide documentation of the TERRA code and its use in assessments. 96 references, 78 figures, 21 tables

  11. Review and analysis of parameters for assessing transport of environmentally released radionuclides through agriculture

    Energy Technology Data Exchange (ETDEWEB)

    Baes, C.F. III; Sharp, R.D.; Sjoreen, A.L.; Shor, R.W.

    1984-09-01

    Most of the default parameters incorporated into the TERRA computer code are documented including a literature review and systematic analysis of element-specific transfer parameters B/sub v/, B/sub r/, F/sub m/, F/sub f/, and K/sub d/. This review and analysis suggests default values which are consistent with the modeling approaches taken in TERRA and may be acceptable for most assessment applications of the computer code. However, particular applications of the code and additional analysis of elemental transport may require alternative default values. Use of the values reported herein in other computer codes simulating terrestrial transport is not advised without careful interpretation of the limitations and scope these analyses. An approach to determination of vegetation-specific interception fractions is also discussed. The limitations of this approach are many, and its use indicates the need for analysis of deposition, interception, and weathering processes. Judgement must be exercised in interpretation of plant surface concentrations generated. Finally, the location-specific agricultural, climatological, and population parameters in the default SITE data base documented. These parameters are intended as alternatives to average values currently used. Indeed, areas in the United States where intensive crop, milk, or beef production occurs will be reflected in the parameter values as will areas where little agricultural activity occurs. However, the original information sources contained some small error and the interpolation and conversion methods used will add more. Parameters used in TERRA not discussed herein are discussed in the companion report to this one - ORNL-5785. In the companion report the models employed in and the coding of TERRA are discussed. These reports together provide documentation of the TERRA code and its use in assessments. 96 references, 78 figures, 21 tables.

  12. JUPITER PROJECT - JOINT UNIVERSAL PARAMETER IDENTIFICATION AND EVALUATION OF RELIABILITY

    Science.gov (United States)

    The JUPITER (Joint Universal Parameter IdenTification and Evaluation of Reliability) project builds on the technology of two widely used codes for sensitivity analysis, data assessment, calibration, and uncertainty analysis of environmental models: PEST and UCODE.

  13. Sediment microbial activity and its relation to environmental variables along the eastern Gulf of Finland coastline

    Science.gov (United States)

    Polyak, Yulia; Shigaeva, Tatyana; Gubelit, Yulia; Bakina, Ludmila; Kudryavtseva, Valentina; Polyak, Mark

    2017-07-01

    Sediment microbial activity and its relationship with the main environmental factors and pollutants were examined in the coastal area of the eastern Gulf of Finland, Baltic Sea. The activity of two common oxidoreductase enzymes: dehydrogenase (DA) and catalase (CA) varied significantly between 13 study sites. In the Neva Bay the highest microbial activities (DA: 2.64 mg TFF (10 g- 1) day- 1, CA: 6.29 mg H2O2 g- 1) were recorded, while in the outer estuary the minimum values of dehydrogenase and catalase were measured. DA, CA, and abundances of culturable heterotrophic bacteria (CHB) were positively correlated with each other, while biomass of green opportunistic algae was independent of both microbial activities and CHB. Enzymatic activity was found to be strongly positively correlated with sediment particle size and organic matter content, but unrelated to the other studied environmental parameters (temperature, pH, and salinity). Principal components analysis (PCA), controlling for environmental variables, supported direct effects of metal and oil contamination on sediment microbial activity. Also it had shown the similar patterns for algal biomass and metals. Our results suggest that copper and hydrocarbons are the main anthropogenic variables influencing enzyme distribution along the eastern Gulf of Finland coastline.

  14. Corporate Environmental Responsibility and Environmental Non-Governmental Organizations in China

    Directory of Open Access Journals (Sweden)

    Zhaojun Yang

    2017-09-01

    Full Text Available In China, environmental non-governmental organizations (ENGOs play an important supervisory role to address ecological issues together with government regulation and enterprise implementation. This study examines the effect of ENGO presence on corporate environmental responsibility (CER performance, along with internal factors as covariate variables. With a sample of 677 enterprises, it operationalizes the independent variable in terms of the number of ENGOs within certain distances from each enterprise, and the dependent variable based on the corporate social responsibility report using the specific criteria in the Global Reporting Initiative (GRI sustainability reporting guidelines. The results of Tobit regression analyses indicate that ENGO presence is conducive to CER performance, and asset size, power concentration, and industry type also make differences. The findings suggest that ENGOs are helpful in solving environment issues by bridging the gap between private and public sectors. Theoretical and practical implications are discussed.

  15. Parameter Estimation in Stochastic Grey-Box Models

    DEFF Research Database (Denmark)

    Kristensen, Niels Rode; Madsen, Henrik; Jørgensen, Sten Bay

    2004-01-01

    An efficient and flexible parameter estimation scheme for grey-box models in the sense of discretely, partially observed Ito stochastic differential equations with measurement noise is presented along with a corresponding software implementation. The estimation scheme is based on the extended...... Kalman filter and features maximum likelihood as well as maximum a posteriori estimation on multiple independent data sets, including irregularly sampled data sets and data sets with occasional outliers and missing observations. The software implementation is compared to an existing software tool...... and proves to have better performance both in terms of quality of estimates for nonlinear systems with significant diffusion and in terms of reproducibility. In particular, the new tool provides more accurate and more consistent estimates of the parameters of the diffusion term....

  16. Environmental attitudes, knowledge, intentions and behaviors among college students.

    Science.gov (United States)

    Levine, Debra Siegel; Strube, Michael J

    2012-01-01

    College students (N = 90) reported their pro-environment behaviors as well as their pro-environment intentions, their explicit and implicit attitudes about the environment, and their knowledge about environmental issues. Intentions and knowledge significantly and independently predicted behavior. Environmental knowledge was not significantly related to attitudes. Implicit and explicit attitudes were significantly but only moderately related. Only explicit attitudes, however, were strongly related to intentions, and intentions completely mediated the influence of explicit attitudes on behavior. Men were found to be more knowledgeable than women about environmental issues; older students had more favorable implicit and explicit environmental attitudes. This research suggests that knowledge about the environment and explicit attitudes influence behavior through different pathways, which may have implications for interventions seeking to increase environmentally friendly behavior.

  17. Parameter extraction using global particle swarm optimization approach and the influence of polymer processing temperature on the solar cell parameters

    Science.gov (United States)

    Kumar, S.; Singh, A.; Dhar, A.

    2017-08-01

    The accurate estimation of the photovoltaic parameters is fundamental to gain an insight of the physical processes occurring inside a photovoltaic device and thereby to optimize its design, fabrication processes, and quality. A simulative approach of accurately determining the device parameters is crucial for cell array and module simulation when applied in practical on-field applications. In this work, we have developed a global particle swarm optimization (GPSO) approach to estimate the different solar cell parameters viz., ideality factor (η), short circuit current (Isc), open circuit voltage (Voc), shunt resistant (Rsh), and series resistance (Rs) with wide a search range of over ±100 % for each model parameter. After validating the accurateness and global search power of the proposed approach with synthetic and noisy data, we applied the technique to the extract the PV parameters of ZnO/PCDTBT based hybrid solar cells (HSCs) prepared under different annealing conditions. Further, we examine the variation of extracted model parameters to unveil the physical processes occurring when different annealing temperatures are employed during the device fabrication and establish the role of improved charge transport in polymer films from independent FET measurements. The evolution of surface morphology, optical absorption, and chemical compositional behaviour of PCDTBT co-polymer films as a function of processing temperature has also been captured in the study and correlated with the findings from the PV parameters extracted using GPSO approach.

  18. Multi-objective optimization model of CNC machining to minimize processing time and environmental impact

    Science.gov (United States)

    Hamada, Aulia; Rosyidi, Cucuk Nur; Jauhari, Wakhid Ahmad

    2017-11-01

    Minimizing processing time in a production system can increase the efficiency of a manufacturing company. Processing time are influenced by application of modern technology and machining parameter. Application of modern technology can be apply by use of CNC machining, one of the machining process can be done with a CNC machining is turning. However, the machining parameters not only affect the processing time but also affect the environmental impact. Hence, optimization model is needed to optimize the machining parameters to minimize the processing time and environmental impact. This research developed a multi-objective optimization to minimize the processing time and environmental impact in CNC turning process which will result in optimal decision variables of cutting speed and feed rate. Environmental impact is converted from environmental burden through the use of eco-indicator 99. The model were solved by using OptQuest optimization software from Oracle Crystal Ball.

  19. Organizing Independent Student Work

    Directory of Open Access Journals (Sweden)

    Zhadyra T. Zhumasheva

    2015-03-01

    Full Text Available This article addresses issues in organizing independent student work. The author defines the term “independence”, discusses the concepts of independent learner work and independent learner work under the guidance of an instructor, proposes a classification of assignments to be done independently, and provides methodological recommendations as to the organization of independent student work. The article discusses the need for turning the student from a passive consumer of knowledge into an active creator of it, capable of formulating a problem, analyzing the ways of solving it, coming up with an optimum outcome, and proving its correctness. The preparation of highly qualified human resources is the primary condition for boosting Kazakhstan’s competitiveness. Independent student work is a means of fostering the professional competence of future specialists. The primary form of self-education is independent work.

  20. Assessment of ELF magnetic fields produced by independent power lines

    International Nuclear Information System (INIS)

    Lucca, G.

    2008-01-01

    In this paper, the problem of assessing the ELF (extremely low-frequency) magnetic fields produced, in a certain area characterised by the presence of more than one independent power line, is faced. The use of the incoherent summation of the single contributions, as an advantageous estimator of the total magnetic field, is proposed and justified by means of a heuristic procedure. This kind of approach can be seen as a useful and practical tool to be employed in environmental impact analysis and in assessing long-term human exposure to ELF magnetic fields. (authors)

  1. Metagenomic covariation along densely sampled environmental gradients in the Red Sea

    Science.gov (United States)

    Thompson, Luke R; Williams, Gareth J; Haroon, Mohamed F; Shibl, Ahmed; Larsen, Peter; Shorenstein, Joshua; Knight, Rob; Stingl, Ulrich

    2017-01-01

    Oceanic microbial diversity covaries with physicochemical parameters. Temperature, for example, explains approximately half of global variation in surface taxonomic abundance. It is unknown, however, whether covariation patterns hold over narrower parameter gradients and spatial scales, and extending to mesopelagic depths. We collected and sequenced 45 epipelagic and mesopelagic microbial metagenomes on a meridional transect through the eastern Red Sea. We asked which environmental parameters explain the most variation in relative abundances of taxonomic groups, gene ortholog groups, and pathways—at a spatial scale of water mass with different physicochemical properties. Temperature explained the most variation in each metric, followed by nitrate, chlorophyll, phosphate, and salinity. That nitrate explained more variation than phosphate suggested nitrogen limitation, consistent with low surface N:P ratios. Covariation of gene ortholog groups with environmental parameters revealed patterns of functional adaptation to the challenging Red Sea environment: high irradiance, temperature, salinity, and low nutrients. Nutrient-acquisition gene ortholog groups were anti-correlated with concentrations of their respective nutrient species, recapturing trends previously observed across much larger distances and environmental gradients. This dataset of metagenomic covariation along densely sampled environmental gradients includes online data exploration supplements, serving as a community resource for marine microbial ecology. PMID:27420030

  2. Evaluation and importance of the environmental concern within the environmental medicine; Erfassung und Bedeutung der Umweltbesorgnis in der Umweltmedizin

    Energy Technology Data Exchange (ETDEWEB)

    Rethage, T.

    2007-07-01

    The book discusses the importance of environmental concerns and annoyance in connection with health-related parameters, such as discomfort, health-related life quality and sleep quality. The evaluation methods and materials (definition of evaluated collectives) are described. The discussion covers the characterization of environmental concerns, their multi-dimensionality and the concerns in case of specific exposures (smells, noise, electromagnetic fields, environment medical ambulance).

  3. Independent contrasts and PGLS regression estimators are equivalent.

    Science.gov (United States)

    Blomberg, Simon P; Lefevre, James G; Wells, Jessie A; Waterhouse, Mary

    2012-05-01

    We prove that the slope parameter of the ordinary least squares regression of phylogenetically independent contrasts (PICs) conducted through the origin is identical to the slope parameter of the method of generalized least squares (GLSs) regression under a Brownian motion model of evolution. This equivalence has several implications: 1. Understanding the structure of the linear model for GLS regression provides insight into when and why phylogeny is important in comparative studies. 2. The limitations of the PIC regression analysis are the same as the limitations of the GLS model. In particular, phylogenetic covariance applies only to the response variable in the regression and the explanatory variable should be regarded as fixed. Calculation of PICs for explanatory variables should be treated as a mathematical idiosyncrasy of the PIC regression algorithm. 3. Since the GLS estimator is the best linear unbiased estimator (BLUE), the slope parameter estimated using PICs is also BLUE. 4. If the slope is estimated using different branch lengths for the explanatory and response variables in the PIC algorithm, the estimator is no longer the BLUE, so this is not recommended. Finally, we discuss whether or not and how to accommodate phylogenetic covariance in regression analyses, particularly in relation to the problem of phylogenetic uncertainty. This discussion is from both frequentist and Bayesian perspectives.

  4. Assessing the Impact of Model Parameter Uncertainty in Simulating Grass Biomass Using a Hybrid Carbon Allocation Strategy

    Science.gov (United States)

    Reyes, J. J.; Adam, J. C.; Tague, C.

    2016-12-01

    Grasslands play an important role in agricultural production as forage for livestock; they also provide a diverse set of ecosystem services including soil carbon (C) storage. The partitioning of C between above and belowground plant compartments (i.e. allocation) is influenced by both plant characteristics and environmental conditions. The objectives of this study are to 1) develop and evaluate a hybrid C allocation strategy suitable for grasslands, and 2) apply this strategy to examine the importance of various parameters related to biogeochemical cycling, photosynthesis, allocation, and soil water drainage on above and belowground biomass. We include allocation as an important process in quantifying the model parameter uncertainty, which identifies the most influential parameters and what processes may require further refinement. For this, we use the Regional Hydro-ecologic Simulation System, a mechanistic model that simulates coupled water and biogeochemical processes. A Latin hypercube sampling scheme was used to develop parameter sets for calibration and evaluation of allocation strategies, as well as parameter uncertainty analysis. We developed the hybrid allocation strategy to integrate both growth-based and resource-limited allocation mechanisms. When evaluating the new strategy simultaneously for above and belowground biomass, it produced a larger number of less biased parameter sets: 16% more compared to resource-limited and 9% more compared to growth-based. This also demonstrates its flexible application across diverse plant types and environmental conditions. We found that higher parameter importance corresponded to sub- or supra-optimal resource availability (i.e. water, nutrients) and temperature ranges (i.e. too hot or cold). For example, photosynthesis-related parameters were more important at sites warmer than the theoretical optimal growth temperature. Therefore, larger values of parameter importance indicate greater relative sensitivity in

  5. Angular Momentum Transport in Turbulent Flow between Independently Rotating Cylinders

    International Nuclear Information System (INIS)

    Paoletti, M. S.; Lathrop, D. P.

    2011-01-01

    We present measurements of the angular momentum flux (torque) in Taylor-Couette flow of water between independently rotating cylinders for all regions of the (Ω 1 , Ω 2 ) parameter space at high Reynolds numbers, where Ω 1 (Ω 2 ) is the inner (outer) cylinder angular velocity. We find that the Rossby number Ro=(Ω 1 -Ω 2 )/Ω 2 fully determines the state and torque G as compared to G(Ro=∞)≡G ∞ . The ratio G/G ∞ is a linear function of Ro -1 in four sections of the parameter space. For flows with radially increasing angular momentum, our measured torques greatly exceed those of previous experiments [Ji et al., Nature (London), 444, 343 (2006)], but agree with the analysis of Richard and Zahn [Astron. Astrophys. 347, 734 (1999)].

  6. Environmental Management Audit: Southwestern Power Administration (Southwestern)

    International Nuclear Information System (INIS)

    1993-03-01

    This report documents the results of the Environmental Management Audit completed for the Southwestern Power Administration. During this Audit, activities and records were reviewed and personnel interviewed. The onsite portion of the Southwestern Audit was conducted from November 30 through December 11, 1992, by the US Department of Energy's Office of Environmental Audit (EH-24). EH-24 carries out independent assessments of Department of Energy (DOE) facilities and activities as part of the Assistant Secretary's Environmental Audit Program. This program is designed to evaluate the status of DOE facilities/activities regarding compliance with laws, regulations, DOE Orders, formal written procedures, compliance agreements, and Best Management Practices (BMPs). This internal oversight function plays an important role in improving the compliance status of DOE operations. The Environmental Management Audit stresses DOE's policy that it is the responsibility of line management to conduct operations in an environmentally sound and safe manner. The Environmental Management Audit focuses on management systems and programs, whereas the Environmental Baseline Audit conducted in March 1991 focused on specific compliance issues. The scope of the Southwestern Environmental Management Audit included a review of all systems and functions necessary for effective environmental management. Specific areas of review included: Organizational Structure; Environmental Commitment; Environmental Protection Programs; Formality of Environmental Programs; Internal and External Communication; Staff Resources, Training, and Development; and Program Evaluation, Reporting, and Corrective Action

  7. Age and growth of the sword razor clam Ensis arcuatus in the Ría de Pontevedra (NW Spain): Influence of environmental parameters

    Science.gov (United States)

    Hernández-Otero, A.; Gaspar, M. B.; Macho, G.; Vázquez, E.

    2014-01-01

    The sword razor clam Ensis arcuatus is the most important commercial species of razor clam in Spain, and its fishery in the Ría de Pontevedra (Galicia, NW Spain) is the most productive. Despite the economic importance of this species, information on its biology is scarce. This study reports shell morphometric relationships, age, and growth rates of E. arcuatus in three fishing beds in the Ría de Pontevedra (Brensa, Bueu and Ons, located in respectively the inner, middle and outer zones of the ria), providing the first estimates of growth parameters for the species in the Iberian Peninsula. Growth was estimated by examination of surface growth rings and internal shell microgrowth patterns (acetate peel technique) that proved to be the most suitable method for growth estimate. Growth of E. arcuatus was slower in Bueu (L∞ = 140.4, k = 0.40) followed by Brensa (L∞ = 151.91, k = 0.40) and Ons (L∞ = 172.7, k = 0.33), and the clams reached commercial size in 1.7, 2.3 and 2.8 years in Ons, Brensa and Bueu, respectively. The differences in growth between sites in relation to environmental parameters are evaluated and the implications for the razor clam fishery are discussed.

  8. Punishability of office-holders in environmental law

    International Nuclear Information System (INIS)

    Papier, H.J.

    1988-01-01

    The author deals with the question of criminal responsibility of office-holders in the field of environmental law. The provisions in secs. 324-330 of the Penal Code do not grant independent or origin protection from violation of the law. They depend on administrative law regulations. (WG) [de

  9. Divison of Environmental Control Technology program, 1978

    International Nuclear Information System (INIS)

    1979-06-01

    This report covers Division of Environmental Control Technology projects in progress during FY 1978, within the Office of the Assistant Secretary for Environment, Department of Energy. It is the second in a planned series of annual reports. The Division of Environmental Control Technology (ECT) continues to support the Assistant Secretary for Environment (EV) in discharging two primary responsibilities: (1) under the Environmental Engineering (EE) Program, the independent overview and assessment of environmental control aspects of both the U.S. Department of Energy's (DOE) research, development, and demonstration (RD and D) programs and the Nation's energy policies, and (2) under the Decontamination and Decommissioning Program, the reduction of potential environmental hazards at the radioactively contaminated sites that are presently owned or were formerly used by the Government. This report presents a short summary of objectives, approach, progress and results, future plans, and a reference bibliography for each research, development, or assessment project within the program areas described above

  10. Divison of Environmental Control Technology program, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Mott, William E.

    1979-06-01

    This report covers Division of Environmental Control Technology projects in progress during FY 1978, within the Office of the Assistant Secretary for Environment, Department of Energy. It is the second in a planned series of annual reports. The Division of Environmental Control Technology (ECT) continues to support the Assistant Secretary for Environment (EV) in discharging two primary responsibilities: (1) under the Environmental Engineering (EE) Program, the independent overview and assessment of environmental control aspects of both the U.S. Department of Energy's (DOE) research, development, and demonstration (RD and D) programs and the Nation's energy policies, and (2) under the Decontamination and Decommissioning Program, the reduction of potential environmental hazards at the radioactively contaminated sites that are presently owned or were formerly used by the Government. This report presents a short summary of objectives, approach, progress and results, future plans, and a reference bibliography for each research, development, or assessment project within the program areas described above.

  11. On the k-independence required by linear probing and minwise independence

    DEFF Research Database (Denmark)

    Pǎtraşcu, Mihai; Thorup, Mikkel

    2016-01-01

    We show that linear probing requires 5-independent hash functions for expected constant-time performance, matching an upper bound of Pagh et al. [2009]. More precisely, we construct a random 4-independent hash function yielding expected logarithmic search time for certain keys. For (1 + ε......)-approximate minwise independence, we show that Ω(lg1 ε)-independent hash functions are required, matching an upper bound of Indyk [2001]. We also show that the very fast 2-independent multiply-shift scheme of Dietzfelbinger [1996] fails badly in both applications....

  12. The utility of environmental exergy analysis for decision making in energy

    International Nuclear Information System (INIS)

    Simpson, Adam P.; Edwards, Chris F.

    2013-01-01

    The analysis framework discussed and employed in this paper utilizes the recent recognition that exergy is a form of environmental free energy to provide a fundamental basis for valuing environmental interactions independent from their secondary impacts. The framework is comprised of two separate components: (1) environmental exergy analysis and (2) anthropocentric sensitivity analysis. Environmental exergy analysis is based on fundamental thermodynamic principles and analysis techniques. It extends the principles of technical exergy analysis to the environment in order to quantify the location, magnitudes, and types of environmental impact—state change, alteration of natural transfers, and destruction change. Anthropocentric sensitivity analysis is based on the concepts of anthropocentric value and anthropocentric sensitivity. It enables the results of environmental exergy analysis to be interpreted for decision making, but at the expense of introducing some subjectivity into the framework. A key attribute of the framework is its ability to evaluate the environmental performance of energy systems on a level playing field, regardless of the specifics of the systems—i.e., resources consumed, products and by-products produced, or system size and time scale. The utility of the analysis framework for decision making is demonstrated in this paper through application to three example energy systems. - Highlights: ► Utilizes the recognition that exergy is a form of environmental free energy. ► Combines environmental exergy analysis and anthropocentric sensitivity analysis. ► Evaluates/compares environmental performance of systems on a level playing field. ► Independence from the system specifics—resources, by-products, sizes, time scales. ► Utility for decision making is demonstrated using real and notional energy systems

  13. Algorithms of control parameters selection for automation of FDM 3D printing process

    Directory of Open Access Journals (Sweden)

    Kogut Paweł

    2017-01-01

    Full Text Available The paper presents algorithms of control parameters selection of the Fused Deposition Modelling (FDM technology in case of an open printing solutions environment and 3DGence ONE printer. The following parameters were distinguished: model mesh density, material flow speed, cooling performance, retraction and printing speeds. These parameters are independent in principle printing system, but in fact to a certain degree that results from the selected printing equipment features. This is the first step for automation of the 3D printing process in FDM technology.

  14. Independent radiographic prognostic factors in patients with hospital-treated community-acquired pneumonia

    International Nuclear Information System (INIS)

    Wilhelm, K.; Textor, J.; Schild, H.; Ewig, S.; Luederitz, B.; Krollmann, G.

    1999-01-01

    Purpose: To evaluate the independent prognostic impact of the chest radiograph for mortality from community-acquired pneumonia requiring hospitalization. Methods: Chest radiographs of 67 patients with hospital-treated community-acquired pneumonia were analyzed with regard to the prognostic implications of radiographic patterns, extent and density of infiltrates, and its evolution during treatment. Results: Non-survivors had a significantly higher extent of infiltrates (p=0.008), density of infiltrates (p=0.05), and radiographic spread during follow-up within 48-72 hours (p=0.0001). In multivariate analysis, persistent or progressive infiltrates were associated with a 47fold increase, and persistent or progressive density of infiltrates with an 18fold increase in risk of mortality. The presence of both parameters could correctly predict 96% of survivors and 90% of non-survivors. Conclusions: The chest radiograph is an independent predictor of the severity of pneumonia. Both persistent or progressive infiltrates and persistent or progressive density of infiltrates are independently associated with mortality from community-acquired pneumonia. (orig.) [de

  15. Recovering a Probabilistic Knowledge Structure by Constraining Its Parameter Space

    Science.gov (United States)

    Stefanutti, Luca; Robusto, Egidio

    2009-01-01

    In the Basic Local Independence Model (BLIM) of Doignon and Falmagne ("Knowledge Spaces," Springer, Berlin, 1999), the probabilistic relationship between the latent knowledge states and the observable response patterns is established by the introduction of a pair of parameters for each of the problems: a lucky guess probability and a careless…

  16. Environmental influences on egg and clutch sizes in lentic- and lotic-breeding salamanders

    Directory of Open Access Journals (Sweden)

    Jon M. Davenport

    2010-12-01

    Full Text Available Recent research indicates that social and environmental factors influence egg and clutch sizes in amphibians. However, most of this work is based on the reproductively diverse order Anura (frogs and toads, whereas less research has been conducted on Caudata (salamanders and Gymnophiona (caecilians. Researchers have suggested that a relationship exists between social and environmental factors and egg and clutch sizes in salamanders, but studies controlling for phylogenetic context are lacking. We could not identify a sufficient number of comparisons for social influences on egg and clutch sizes; therefore, we focused on environmental influences for this study. Data on egg size, clutch size, environmental factors, and phylogenies for salamanders were assembled from the scientific literature. We used independent, pair-wise comparisons to investigate the association of larval salamander habitat and egg size and the association of larval salamander habitat with clutch sizes within a phylogenetic framework. There is a significant association between larval habitat and egg size; specifically, stream-breeding species produce larger eggs. There is no significant association between larval habitat and clutchsize. Our study confirms earlier reports that salamander egg size is associated with larval environments, but is the first to use phylogenetically independent contrasts to account for the lack of phylogenetic independence of the traits measured (egg size and clutch size associated with many of the diverse lineages. Our study shows that environmental selection pressure can be quite strong on one aspect of salamander reproduction—egg size.

  17. Environmental and zooplankton parameter changes during the drying of a saline shallow temporary lake in central Argentina

    Directory of Open Access Journals (Sweden)

    Alicia María Vignatti

    2017-09-01

    Full Text Available Central Argentina has numerous saline lakes sustained by groundwater sources and rainfall. These lakes are temporary and experience significant changes in water level and salinity, depending on wet and dry climate cycles. This study aims to investigate the scarcely known dynamics of environmental and zooplankton parameters during the drying phase of one of these lakes. Monthly samples were taken from December 2 012 to July 2 013 in the Ojo de Agua Uriburu lake, previous to its drying. At the beginning of the study, the lake’s depth was 0.7 m and its salinity was 16.65 g L−1, later, in July, its depth decreased to 0.06 m and its salinity increased to 92.9 g L−1. Zooplankton species richness was low (three crustaceans and three rotifers, with Boeckella poopoensis and Moina eugeniae dominating in the system. Maximum density and biomass were attained by the two dominant species in April (318.5 i nd L−1 and 3 029.1 µg L−1 dry weight; and 242.4 i nd L −1 and 1 530.4 µg L−1 dry weight, for B. poopoensis and M. ugeniae, respectively, and no correlation was found between these parameters and salinity. Maximum average body lengths for both species were observed in the last months of sampling (M. eugeniae: 1 020 ± 84.2 µm and B. poopoensis: 1 348.8 ± 89.0 µm. At this point of the study, neither juvenile nor larval stages were found. The increase in average body size is, arguably, the result of increased salinity in the system through a negative effect on reproduction. Because this lake reached hypersalinity, its ecological dynamics are unique among those of other temporary, saline lakes that dried in central Argentina. Similar studies on other temporary ecosystems are needed to increase the information on these little known ecological aspects.

  18. Model-independent separation of poorly resolved hypperfine split spectra by a linear combination method

    International Nuclear Information System (INIS)

    Nagy, D.L.; Dengler, J.; Ritter, G.

    1988-01-01

    A model-independent evaluation of the components of poorly resolved Moessbauer spectra based on a linear combination method is possible if there is a parameter as a function of which the shape of the individual components do not but their intensities do change and the dependence of the intensities on this parameter is known. The efficiency of the method is demonstrated on the example of low temperature magnetically split spectra of the high-T c superconductor YBa 2 (Cu 0.9 Fe 0 .1 ) 3 O 7-y . (author)

  19. Transformation-based spherical cloaks designed by an implicit transformation-independent method: theory and optimization

    International Nuclear Information System (INIS)

    Novitsky, Andrey; Qiu, C-W; Zouhdi, Said

    2009-01-01

    Based on the concept of the cloak generating function, we propose an implicit transformation-independent method for the required parameters of spherical cloaks without knowing the needed coordinate transformation beforehand. A non-ideal discrete model is used to calculate and optimize the total scattering cross-sections of different profiles of the generating function. A bell-shaped quadratic spherical cloak is found to be the best candidate, which is further optimized by controlling the design parameters involved. Such improved invisibility is steady even when the model is highly discretized.

  20. Habitat characteristics and environmental parameters influencing fish assemblages of karstic pools in southern Mexico

    Directory of Open Access Journals (Sweden)

    María Eugenia Vega-Cendejas

    Full Text Available Fish assemblage structure was evaluated and compared among 36 karstic pools located within protected areas of the Calakmul Biosphere Reserve (southern Mexico and unprotected adjacent areas beyond the Reserve. Nonmetric multidimensional scaling (MDS, indicator species analysis (ISA, and canonical correspondence analysis (CCA were used to identify which environmental factors reflected local influences and to evaluate the correlation of these variables with fish assemblages structure. Thirty-one species were encountered in these karstic pools, some for the first time within the Reserve. These aquatic environments were separated into three groups based on physico-chemical characteristics. Although CCA identified significant associations between several fish species (based on their relative abundance and environmental variables (K, NH4, NO3, and conductivity, the most abundant species (Astyanax aeneus, Poecilia mexicana, and Gambusia sexradiata occur in most pools and under several environmental conditions. Baseline data on fish diversity along with a continued monitoring program are essential in order to evaluate the conservation status of fish assemblages and their habitats, as well as to measure the influence of anthropogenic impacts on pristine habitats such as the karstic pools of the Calakmul Biosphere Reserve.

  1. Probabilistic estimation of the constitutive parameters of polymers

    Directory of Open Access Journals (Sweden)

    Siviour C.R.

    2012-08-01

    Full Text Available The Mulliken-Boyce constitutive model predicts the dynamic response of crystalline polymers as a function of strain rate and temperature. This paper describes the Mulliken-Boyce model-based estimation of the constitutive parameters in a Bayesian probabilistic framework. Experimental data from dynamic mechanical analysis and dynamic compression of PVC samples over a wide range of strain rates are analyzed. Both experimental uncertainty and natural variations in the material properties are simultaneously considered as independent and joint distributions; the posterior probability distributions are shown and compared with prior estimates of the material constitutive parameters. Additionally, particular statistical distributions are shown to be effective at capturing the rate and temperature dependence of internal phase transitions in DMA data.

  2. Origin of path independence between cumulative CO2 emissions and global warming

    Science.gov (United States)

    Seshadri, Ashwin K.

    2017-11-01

    Observations and GCMs exhibit approximate proportionality between cumulative carbon dioxide (CO2) emissions and global warming. Here we identify sufficient conditions for the relationship between cumulative CO2 emissions and global warming to be independent of the path of CO2 emissions; referred to as "path independence". Our starting point is a closed form expression for global warming in a two-box energy balance model (EBM), which depends explicitly on cumulative emissions, airborne fraction and time. Path independence requires that this function can be approximated as depending on cumulative emissions alone. We show that path independence arises from weak constraints, occurring if the timescale for changes in cumulative emissions (equal to ratio between cumulative emissions and emissions rate) is small compared to the timescale for changes in airborne fraction (which depends on CO2 uptake), and also small relative to a derived climate model parameter called the damping-timescale, which is related to the rate at which deep-ocean warming affects global warming. Effects of uncertainties in the climate model and carbon cycle are examined. Large deep-ocean heat capacity in the Earth system is not necessary for path independence, which appears resilient to climate modeling uncertainties. However long time-constants in the Earth system carbon cycle are essential, ensuring that airborne fraction changes slowly with timescale much longer than the timescale for changes in cumulative emissions. Therefore path independence between cumulative emissions and warming cannot arise for short-lived greenhouse gases.

  3. Relating stick-slip friction experiments to earthquake source parameters

    Science.gov (United States)

    McGarr, Arthur F.

    2012-01-01

    Analytical results for parameters, such as static stress drop, for stick-slip friction experiments, with arbitrary input parameters, can be determined by solving an energy-balance equation. These results can then be related to a given earthquake based on its seismic moment and the maximum slip within its rupture zone, assuming that the rupture process entails the same physics as stick-slip friction. This analysis yields overshoots and ratios of apparent stress to static stress drop of about 0.25. The inferred earthquake source parameters static stress drop, apparent stress, slip rate, and radiated energy are robust inasmuch as they are largely independent of the experimental parameters used in their estimation. Instead, these earthquake parameters depend on C, the ratio of maximum slip to the cube root of the seismic moment. C is controlled by the normal stress applied to the rupture plane and the difference between the static and dynamic coefficients of friction. Estimating yield stress and seismic efficiency using the same procedure is only possible when the actual static and dynamic coefficients of friction are known within the earthquake rupture zone.

  4. On the validity of evolutionary models with site-specific parameters.

    Directory of Open Access Journals (Sweden)

    Konrad Scheffler

    Full Text Available Evolutionary models that make use of site-specific parameters have recently been criticized on the grounds that parameter estimates obtained under such models can be unreliable and lack theoretical guarantees of convergence. We present a simulation study providing empirical evidence that a simple version of the models in question does exhibit sensible convergence behavior and that additional taxa, despite not being independent of each other, lead to improved parameter estimates. Although it would be desirable to have theoretical guarantees of this, we argue that such guarantees would not be sufficient to justify the use of these models in practice. Instead, we emphasize the importance of taking the variance of parameter estimates into account rather than blindly trusting point estimates - this is standardly done by using the models to construct statistical hypothesis tests, which are then validated empirically via simulation studies.

  5. Community Design Parameters and the Performance of Residential Cogeneration Systems

    Directory of Open Access Journals (Sweden)

    Hazem Rashed-Ali

    2012-11-01

    Full Text Available The integration of cogeneration systems in residential and mixed-use communities has the potential of reducing their energy demand and harmful emissions and can thus play asignificant role in increasing their environmental sustainability. This study investigated the impact of selected planning and architectural design parameters on the environmental and economic performances of centralized cogeneration systems integrated into residential communities in U.S.cold climates. Parameters investigated include: 1 density, 2 use mix, 3 street configuration, 4 housing typology, 5 envelope and building systems’ efficiencies, and 6 passive solar energyutilization. The study integrated several simulation tools into a procedure to assess the impact of each design parameter on the cogeneration system performance. This assessment procedure included: developing a base-line model representing typical design characteristics of U.S. residential communities; assessing the cogeneration system’s performance within this model using three performance indicators: percentage of reduction in primary energy use, percentage of reduction in CO2 emissions; and internal rate of return; assessing the impact of each parameter on the system performance through developing 46 design variations of the base-line model representing potential changes in each parameter and calculating the three indicators for each variation; and finally, using a multi-attribute decision analysis methodology to evaluate the relative impact of each parameter on the cogeneration system performance. The study results show that planning parameters had a higher impact on the cogeneration system performance than architectural ones. Also, a significant correlation was found between design characteristics identified as favorable for the cogeneration system performance and those of sustainable residential communities. These include high densities, high use mix, interconnected street networks, and mixing of

  6. Environment and environmental impacts

    OpenAIRE

    Rejane de Fátima Victor Vasconcelos

    2009-01-01

    The article shows what can be environmental impacts and how those happen, both by the actions made by human kind and by natural disasters. Another concern of the research is the unstoppable incident of the natural resources destruction, result f the globalization actions and the economy, and that the environment impacts have happen in every direction, independently of the geographic scale, harming the life in earth, without giving importance who is the target. The article made reference to in...

  7. Action-reaction based parameters identification and states estimation of flexible systems

    OpenAIRE

    Khalil, Islam; Kunt, Emrah Deniz; Şabanoviç, Asif; Sabanovic, Asif

    2012-01-01

    This work attempts to identify and estimate flexible system's parameters and states by a simple utilization of the Action-Reaction law of dynamical systems. Attached actuator to a dynamical system or environmental interaction imposes an action that is instantaneously followed by a dynamical system reaction. The dynamical system's reaction carries full information about the dynamical system including system parameters, dynamics and externally applied forces that arise due to system interaction...

  8. ATLAS parameter study

    International Nuclear Information System (INIS)

    Adler, R.J.

    1994-01-01

    The purpose of this study is to make an independent assessment on the parameters chosen for the ATLAS capacitor bank at LANL. The contractor will perform a study of the basic pulsed power parameters of the ATLAS device with baseline functional parameters of >25 MA implosion current and <2.5 microsecond current risetime. Nominal circuit parameters held fixed will be the 14 nH from the vacuum interface to the load, and the nominal load impedances of 1 milliohm for slow loads and 10 milliohms for fast loads. Single Ended designs, as opposed to bipolar designs, will be studied in detail. The ATLAS pulsed power design problem is about inductance. The reason that a 36 MJ bank is required is that such a bank has enough individual capacitors so that the parallel inductance is acceptably low. Since about half the inductance is in the bank, and the inductance and time constant of the submodules is fixed, the variation of output with a given parameter will generally be a weak one. In general, the dl/dt calculation demonstrates that for the real system inductances, 700 kV is the optimum voltage for the bank to drive X-ray loads. The optimum is broad, and there is little reduction in performance at voltages as low as 450 kV. The direct drive velocity analysis also shows that the optimum velocity is between 480 and 800 kV for a variety of assumptions, and that there is less than a 10% variation in velocity over this range. Voltages in the 120 kV--600 kV range are desirable for driving heavy liners. A compromise optimum operating point might be 480 kV, at which all X-ray operation scenarios are within 10% of their velocity optimum, and heavy liners can be configured to be near optimum if small enough. Based on very preliminary studies the author believes that the choice of a single operating voltage point (say, 480 kV) is unnecessary, and that a bank engineered for dual operation at 480 and 240 kV will be the best solution to the ATLAS problem

  9. Environmental Management Model for Road Maintenance Operation Involving Community Participation

    Science.gov (United States)

    Triyono, A. R. H.; Setyawan, A.; Sobriyah; Setiono, P.

    2017-07-01

    Public expectations of Central Java, which is very high on demand fulfillment, especially road infrastructure as outlined in the number of complaints and community expectations tweeter, Short Mail Massage (SMS), e-mail and public reports from various media, Highways Department of Central Java province requires development model of environmental management in the implementation of a routine way by involving the community in order to fulfill the conditions of a representative, may serve road users safely and comfortably. This study used survey method with SEM analysis and SWOT with Latent Independent Variable (X), namely; Public Participation in the regulation, development, construction and supervision of road (PSM); Public behavior in the utilization of the road (PMJ) Provincial Road Service (PJP); Safety in the Provincial Road (KJP); Integrated Management System (SMT) and latent dependent variable (Y) routine maintenance of the provincial road that is integrated with the environmental management system and involve the participation of the community (MML). The result showed the implementation of routine maintenance of road conditions in Central Java province has yet to implement an environmental management by involving the community; Therefore developed environmental management model with the results of H1: Community Participation (PSM) has positive influence on the Model of Environmental Management (MML); H2: Behavior Society in Jalan Utilization (PMJ) positive effect on Model Environmental Management (MML); H3: Provincial Road Service (PJP) positive effect on Model Environmental Management (MML); H4: Safety in the Provincial Road (KJP) positive effect on Model Environmental Management (MML); H5: Integrated Management System (SMT) has positive influence on the Model of Environmental Management (MML). From the analysis obtained formulation model describing the relationship / influence of the independent variables PSM, PMJ, PJP, KJP, and SMT on the dependent variable

  10. Revised models and genetic parameter estimates for production and ...

    African Journals Online (AJOL)

    Genetic parameters for production and reproduction traits in the Elsenburg Dormer sheep stud were estimated using records of 11743 lambs born between 1943 and 2002. An animal model with direct and maternal additive, maternal permanent and temporary environmental effects was fitted for traits considered traits of the ...

  11. Distributed Large Independent Sets in One Round On Bounded-independence Graphs

    OpenAIRE

    Halldorsson , Magnus M.; Konrad , Christian

    2015-01-01

    International audience; We present a randomized one-round, single-bit messages, distributed algorithm for the maximum independent set problem in polynomially bounded-independence graphs with poly-logarithmic approximation factor. Bounded-independence graphs capture various models of wireless networks such as the unit disc graphs model and the quasi unit disc graphs model. For instance, on unit disc graphs, our achieved approximation ratio is O((log(n)/log(log(n)))^2).A starting point of our w...

  12. Reducing the uncertainty of parameters controlling seasonal carbon and water fluxes in Chinese forests and its implication for simulated climate sensitivities

    Science.gov (United States)

    Li, Yue; Yang, Hui; Wang, Tao; MacBean, Natasha; Bacour, Cédric; Ciais, Philippe; Zhang, Yiping; Zhou, Guangsheng; Piao, Shilong

    2017-08-01

    Reducing parameter uncertainty of process-based terrestrial ecosystem models (TEMs) is one of the primary targets for accurately estimating carbon budgets and predicting ecosystem responses to climate change. However, parameters in TEMs are rarely constrained by observations from Chinese forest ecosystems, which are important carbon sink over the northern hemispheric land. In this study, eddy covariance data from six forest sites in China are used to optimize parameters of the ORganizing Carbon and Hydrology In Dynamics EcosystEms TEM. The model-data assimilation through parameter optimization largely reduces the prior model errors and improves the simulated seasonal cycle and summer diurnal cycle of net ecosystem exchange, latent heat fluxes, and gross primary production and ecosystem respiration. Climate change experiments based on the optimized model are deployed to indicate that forest net primary production (NPP) is suppressed in response to warming in the southern China but stimulated in the northeastern China. Altered precipitation has an asymmetric impact on forest NPP at sites in water-limited regions, with the optimization-induced reduction in response of NPP to precipitation decline being as large as 61% at a deciduous broadleaf forest site. We find that seasonal optimization alters forest carbon cycle responses to environmental change, with the parameter optimization consistently reducing the simulated positive response of heterotrophic respiration to warming. Evaluations from independent observations suggest that improving model structure still matters most for long-term carbon stock and its changes, in particular, nutrient- and age-related changes of photosynthetic rates, carbon allocation, and tree mortality.

  13. Ways to improve the environmental conditions of their buses in operation on passenger routes of cities

    Directory of Open Access Journals (Sweden)

    Melnychuk S.V.

    2017-04-01

    Full Text Available The results of studies on operational and environmental parameters buses used on bus routes Zhitomir city. It uses statistical methods for determining the intensity of traffic, passenger traffic and ecology in traffic. To assess the environmental chosen stop with the greatest intensity of traffic, which is the probability of accumulation of pollution transport emissions that exceed permissible limits. Calculation of environmental pollution emission route for vehicles made stops street «Str. Hundreds of Heaven» «CUM», «vul. Hlibna» on the main trunk street Kievska. Results obtained environmental field experiments compared with the data defined calculation methods, based on the proposed use appropriate operational vehicles. The conclusions that indicate the seriousness of the problem and the urgency to address it. The system of environmental safety and road safety in Zhitomir requires significant improvements due to the increased quantities bus vehicles plying city routes. Recommendations to improve the ecological condition of intersections can be developed through the optimization of traffic using buses with environmentally improved operating parameters. Keywords: environmental and operational parameters; ecological safety; environmental assessment; intensity of traffic; passenger traffic; environmental conditions; operation; bus choice; stop.

  14. Method for environmental risk analysis (MIRA) revision 2007

    International Nuclear Information System (INIS)

    2007-04-01

    OLF's instruction manual for carrying out environmental risk analyses provides a united approach and a common framework for environmental risk assessments. This is based on the best information available. The manual implies standardizations of a series of parameters, input data and partial analyses that are included in the environmental risk analysis. Environmental risk analyses carried out according to the MIRA method will thus be comparable between fields and between companies. In this revision an update of the text in accordance with today's practice for environmental risk analyses and prevailing regulations is emphasized. Moreover, method adjustments for especially protected beach habitats have been introduced, as well as a general method for estimating environmental risk concerning fish. Emphasis has also been put on improving environmental risk analysis' possibilities to contribute to a better management of environmental risk in the companies (ml)

  15. AS3MT-mediated tolerance to arsenic evolved by multiple independent horizontal gene transfers from bacteria to eukaryotes

    DEFF Research Database (Denmark)

    Palmgren, Michael; Engström, Karin; Hallström, Björn M.

    2017-01-01

    the evolutionary origin of AS3MT and assessed the ability of different genotypes to produce methylated arsenic metabolites. Phylogenetic analysis suggests that multiple, independent horizontal gene transfers between different bacteria, and from bacteria to eukaryotes, increased tolerance to environmental arsenic...

  16. The effect of thermal and radiation accelerated ageing on the A. C. electric motor parameters

    International Nuclear Information System (INIS)

    Pica, I.; Segarceanu, D.

    2000-01-01

    The paper presents the main aspects concerning the electric parameters variation of triphase asynchronous motors operating under specific environmental conditions determined by temperature, humidity, radiation. The testing of electric motor capability to meet and exceed the required performances all along its operating life implies the performing of thermal and radiation ageing while the motor is brought, in a relatively short time, under conditions equivalent to those at the end of its service life. The paper describes ageing and measurement techniques and the analyses of electric parameter behavior in these environmental simulated conditions. (author)

  17. Parameter Estimation for Thurstone Choice Models

    Energy Technology Data Exchange (ETDEWEB)

    Vojnovic, Milan [London School of Economics (United Kingdom); Yun, Seyoung [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-04-24

    We consider the estimation accuracy of individual strength parameters of a Thurstone choice model when each input observation consists of a choice of one item from a set of two or more items (so called top-1 lists). This model accommodates the well-known choice models such as the Luce choice model for comparison sets of two or more items and the Bradley-Terry model for pair comparisons. We provide a tight characterization of the mean squared error of the maximum likelihood parameter estimator. We also provide similar characterizations for parameter estimators defined by a rank-breaking method, which amounts to deducing one or more pair comparisons from a comparison of two or more items, assuming independence of these pair comparisons, and maximizing a likelihood function derived under these assumptions. We also consider a related binary classification problem where each individual parameter takes value from a set of two possible values and the goal is to correctly classify all items within a prescribed classification error. The results of this paper shed light on how the parameter estimation accuracy depends on given Thurstone choice model and the structure of comparison sets. In particular, we found that for unbiased input comparison sets of a given cardinality, when in expectation each comparison set of given cardinality occurs the same number of times, for a broad class of Thurstone choice models, the mean squared error decreases with the cardinality of comparison sets, but only marginally according to a diminishing returns relation. On the other hand, we found that there exist Thurstone choice models for which the mean squared error of the maximum likelihood parameter estimator can decrease much faster with the cardinality of comparison sets. We report empirical evaluation of some claims and key parameters revealed by theory using both synthetic and real-world input data from some popular sport competitions and online labor platforms.

  18. SPOTting Model Parameters Using a Ready-Made Python Package.

    Directory of Open Access Journals (Sweden)

    Tobias Houska

    Full Text Available The choice for specific parameter estimation methods is often more dependent on its availability than its performance. We developed SPOTPY (Statistical Parameter Optimization Tool, an open source python package containing a comprehensive set of methods typically used to calibrate, analyze and optimize parameters for a wide range of ecological models. SPOTPY currently contains eight widely used algorithms, 11 objective functions, and can sample from eight parameter distributions. SPOTPY has a model-independent structure and can be run in parallel from the workstation to large computation clusters using the Message Passing Interface (MPI. We tested SPOTPY in five different case studies to parameterize the Rosenbrock, Griewank and Ackley functions, a one-dimensional physically based soil moisture routine, where we searched for parameters of the van Genuchten-Mualem function and a calibration of a biogeochemistry model with different objective functions. The case studies reveal that the implemented SPOTPY methods can be used for any model with just a minimal amount of code for maximal power of parameter optimization. They further show the benefit of having one package at hand that includes number of well performing parameter search methods, since not every case study can be solved sufficiently with every algorithm or every objective function.

  19. A Fundamental Parameter-Based Calibration Model for an Intrinsic Germanium X-Ray Fluorescence Spectrometer

    DEFF Research Database (Denmark)

    Christensen, Leif Højslet; Pind, Niels

    1982-01-01

    A matrix-independent fundamental parameter-based calibration model for an energy-dispersive X-ray fluorescence spectrometer has been developed. This model, which is part of a fundamental parameter approach quantification method, accounts for both the excitation and detection probability. For each...... secondary target a number of relative calibration constants are calculated on the basis of knowledge of the irradiation geometry, the detector specifications, and tabulated fundamental physical parameters. The absolute calibration of the spectrometer is performed by measuring one pure element standard per...

  20. Greek economic crisis and impaired perinatal parameters: experience from a public maternity hospital.

    Science.gov (United States)

    Sdona, E; Papamichail, D; Ragkou, E; Briana, D D; Malamitsi-Puchner, A; Panagiotopoulos, T

    2017-07-04

    Since 2008, Greece suffers a severe economic crisis. Adverse health outcomes have been reported, but studies on perinatal health are sparse. We aimed to examine the impact of economic crisis on perinatal parameters during early and established crisis periods. Birth records of 14 923 neonates, born in a public maternity hospital from 2005-2014, were reviewed for maternal (age, delivery mode) and neonatal (gender, birthweight, gestational age) variables. Univariable analysis tested the association of study variables with time-periods 2005-2007, 2009-2011 and 2012-2014. Multivariable logistic regression analysis identified factors independently associated with low birthweight (LBW) (period, independently of maternal age. In conclusion, impaired perinatal parameters, manifested by increasing maternal age, LBW, prematurity and CS rate, were observed during the years of economic decline, with possible adverse consequences for later health.

  1. A comparison on parameter-estimation methods in multiple regression analysis with existence of multicollinearity among independent variables

    Directory of Open Access Journals (Sweden)

    Hukharnsusatrue, A.

    2005-11-01

    Full Text Available The objective of this research is to compare multiple regression coefficients estimating methods with existence of multicollinearity among independent variables. The estimation methods are Ordinary Least Squares method (OLS, Restricted Least Squares method (RLS, Restricted Ridge Regression method (RRR and Restricted Liu method (RL when restrictions are true and restrictions are not true. The study used the Monte Carlo Simulation method. The experiment was repeated 1,000 times under each situation. The analyzed results of the data are demonstrated as follows. CASE 1: The restrictions are true. In all cases, RRR and RL methods have a smaller Average Mean Square Error (AMSE than OLS and RLS method, respectively. RRR method provides the smallest AMSE when the level of correlations is high and also provides the smallest AMSE for all level of correlations and all sample sizes when standard deviation is equal to 5. However, RL method provides the smallest AMSE when the level of correlations is low and middle, except in the case of standard deviation equal to 3, small sample sizes, RRR method provides the smallest AMSE.The AMSE varies with, most to least, respectively, level of correlations, standard deviation and number of independent variables but inversely with to sample size.CASE 2: The restrictions are not true.In all cases, RRR method provides the smallest AMSE, except in the case of standard deviation equal to 1 and error of restrictions equal to 5%, OLS method provides the smallest AMSE when the level of correlations is low or median and there is a large sample size, but the small sample sizes, RL method provides the smallest AMSE. In addition, when error of restrictions is increased, OLS method provides the smallest AMSE for all level, of correlations and all sample sizes, except when the level of correlations is high and sample sizes small. Moreover, the case OLS method provides the smallest AMSE, the most RLS method has a smaller AMSE than

  2. An Assessment of Physicochemical Parameters of Selected Industrial Effluents in Nepal

    Directory of Open Access Journals (Sweden)

    Abhinay Man Shrestha

    2017-01-01

    Full Text Available It is a well-known fact that the effluents released from the industries and environmental degradation go hand in hand. With the ongoing global industrialization this problem has been further aggravated. As such, Nepal is no exception. Hundreds of industries are being registered in the country annually which inevitably brings the issues regarding environmental pollution. This study has been conducted with samples of wastewater from 5 different industrial sites in 4 districts of Nepal, namely, Makwanpur, Sunsari, Morang, and Kathmandu, among which two were Waste Water Treatment Plants which treated the combined effluents collected from various sources. The other three sites were from wires and cables industry, paint manufacturing industry, and plastic cutting industry. The physicochemical parameters analysed were pH, temperature, conductivity, turbidity, and Cu, Cr, SO42-, and PO43- levels. Possible onsite measurements were recorded using portable, handheld devices whereas other parameters were assessed in the laboratory. The observed parameter levels in the collected samples were compared against the available Nepal national standards for industrial effluents and in the absence of standards for industrial effluents, with other relevant standard levels. Most of the parameters analysed were within the permissible limits with the exception of pH and Cr levels in some sites.

  3. Scanning anisotropy parameters in complex media

    KAUST Repository

    Alkhalifah, Tariq Ali

    2011-01-01

    Parameter estimation in an inhomogeneous anisotropic medium offers many challenges; chief among them is the trade-off between inhomogeneity and anisotropy. It is especially hard to estimate the anisotropy anellipticity parameter η in complex media. Using perturbation theory and Taylor’s series, I have expanded the solutions of the anisotropic eikonal equation for transversely isotropic (TI) media with a vertical symmetry axis (VTI) in terms of the independent parameter η from a generally inhomogeneous elliptically anisotropic medium background. This new VTI traveltime solution is based on a set of precomputed perturbations extracted from solving linear partial differential equations. The traveltimes obtained from these equations serve as the coefficients of a Taylor-type expansion of the total traveltime in terms of η. Shanks transform is used to predict the transient behavior of the expansion and improve its accuracy using fewer terms. A homogeneous medium simplification of the expansion provides classical nonhyperbolic moveout descriptions of the traveltime that are more accurate than other recently derived approximations. In addition, this formulation provides a tool to scan for anisotropic parameters in a generally inhomogeneous medium background. A Marmousi test demonstrates the accuracy of this approximation. For a tilted axis of symmetry, the equations are still applicable with a slightly more complicated framework because the vertical velocity and δ are not readily available from the data.

  4. Scanning anisotropy parameters in complex media

    KAUST Repository

    Alkhalifah, Tariq Ali

    2011-03-21

    Parameter estimation in an inhomogeneous anisotropic medium offers many challenges; chief among them is the trade-off between inhomogeneity and anisotropy. It is especially hard to estimate the anisotropy anellipticity parameter η in complex media. Using perturbation theory and Taylor’s series, I have expanded the solutions of the anisotropic eikonal equation for transversely isotropic (TI) media with a vertical symmetry axis (VTI) in terms of the independent parameter η from a generally inhomogeneous elliptically anisotropic medium background. This new VTI traveltime solution is based on a set of precomputed perturbations extracted from solving linear partial differential equations. The traveltimes obtained from these equations serve as the coefficients of a Taylor-type expansion of the total traveltime in terms of η. Shanks transform is used to predict the transient behavior of the expansion and improve its accuracy using fewer terms. A homogeneous medium simplification of the expansion provides classical nonhyperbolic moveout descriptions of the traveltime that are more accurate than other recently derived approximations. In addition, this formulation provides a tool to scan for anisotropic parameters in a generally inhomogeneous medium background. A Marmousi test demonstrates the accuracy of this approximation. For a tilted axis of symmetry, the equations are still applicable with a slightly more complicated framework because the vertical velocity and δ are not readily available from the data.

  5. A generalized model for site percolation with two independent concentrations

    International Nuclear Information System (INIS)

    Lin Jiancheng.

    1987-05-01

    In this paper the usual site percolation problem with single concentration is generalized to the one that contains two independent concentrations. Using the real space renormalization technique we derive an exact transformation for the one dimensional lattice and a cluster transformation for triangle lattice in two dimensions. The critical exponents and the percolation threshold concentrations obtained are the same as those of the usual single concentration percolation problem. Critical line and flow diagram in the two concentration parameters space are also given. (author). 10 refs, 6 figs

  6. Site environmental report for Calendar Year 1994 on radiological and nonradiological parameters

    International Nuclear Information System (INIS)

    1995-01-01

    Battelle Memorial Institute's nuclear research facilities are currently being maintained in a surveillance and maintenance (S ampersand M) mode with continual decontamination and decommissioning (D ampersand D) activities being conducted under Department of Energy (DOE) Contract W-7405-ENG-92. These activities are referred to under the Contract as the Battelle Columbus Laboratories Decommissioning Project (BCLDP). Operations referenced in this report are performed in support of S ampersand M and D ampersand D activities. Battelle's King Avenue facility is not considered in this report to the extent that the West Jefferson facility is. The source term at the King Avenue site is a small fraction of the source term at the West Jefferson site. Off site levels of radionuclides that could be attributed to the west Jefferson and King Avenue nuclear operations wereindistinguishable from background levels at specific locations where air, water, and direct radiation measurements were performed. Environmental monitoring continued to demonstrate compliance by Battelle with federal, state and local regulations. Routine, nonradiological activities performed include monitoring liquid effluents and monitoring the ground water system for the West Jefferson North site. Samples of various environmental media including air, water, grass, fish, field and garden crops, sediment and soil were collected from the region surrounding the two sites and analyzed

  7. Lipoprotein (a) and biochemical parameters in elderly

    OpenAIRE

    Yuttana Sudjaroen

    2016-01-01

    Background: Lipoprotein (a) [Lp(a)] is an low-density lipoprotein like particle and is an important independent risk factor for coronary artery diseases (CAD). Few studies on Lp(a) level in Thai elderly to screening risk of CAD may concerned. Aims: To study the relation of Lp(a) level and routine biochemical parameters including lipid profiles and fasting blood glucose in elderly and to determine risk of subclinical symptoms by using Lp(a) levels as early risk predictor. Settings and Design: ...

  8. Environmental management (Republic of Macedonia)

    International Nuclear Information System (INIS)

    1997-01-01

    A number of institutions are responsible for environmental monitoring, however, coordination between these agencies is poor. Also, not all parameters typically used to index pollution are measured due to lack of resources, unavailability of chemicals for analysis and obsolete equipment. The cause-effect relationship between health and pollution is not clearly known, except for a new urban areas. In order to create an efficient environmental management system, alterations of the present institutional structure are imperative. It is necessary to strengthen the Ministry of Urban Planning, Construction and Development as a short-term task to consider the need for establishing a separate Ministry of Environment in the long-term. The Ministry of Environment should be supported by an Environmental Institute, a modern inspection service and a department for staff training and international cooperation. The need to reinforce local units responsible for environmental enforcement is especially emphasized. (author)

  9. A model for rate-dependent but time-independent material behavior in cyclic plasticity

    International Nuclear Information System (INIS)

    Dafalias, Y.F.; Ramey, M.R.; Sheikh, I.

    1977-01-01

    It is the purpose of this paper to present a model for rate-dependent but time independent material behavior under cyclic loading in the plastic range. What is referred to as time independent behavior here, is the absence of creep and relaxation phenomena from the behavior of the model. The notion of plastic internal variables (piv) is introduced, as properly invariant scalars or second order tensors, whose constitutive relations are rate-type equations not necessarily homogeneous of oder one in the rates, as it would be required for independent plasticity. The concept of a yield surface in the strain space and a loading function in terms of the total strain rate is introduced, where the sign of the loading function defines zero or non-zero value of the rate of piv. Thus rate dependence is achieved without time dependent behavior (no creep or relaxation). In addition, discrete memory parameters associated with the most recent event of unloading-reloading in different directions enter the constitutive relations for the piv. A particular form of the constitutive relations is assumed, where the rate of piv is a linear combination of the strain rate components, with coefficients depending on the second invariant of the strain rate tensor, which can be viewed as a scalar measure of the rate of deformation in the multiaxial case and a direct generalization of the uniaxial strain rate. This leads to a particularly simple form of the constitutive relations resembling the ones for rate independent plasticity. The uniaxial counterpart would be a relation between the plastic strain rate (as one of the piv) and the total strain rate through a plastic modulus which depends on the strain rate, the piv, and the discrete memory parameters

  10. Combined culture-based and culture-independent approaches provide insights into diversity of jakobids, an extremely plesiomorphic eukaryotic lineage

    Directory of Open Access Journals (Sweden)

    Tomáš ePánek

    2015-11-01

    Full Text Available We used culture-based and culture-independent approaches to discover diversity and ecology of anaerobic jakobids (Excavata: Jakobida, an overlooked, deep-branching lineage of free-living nanoflagellates related to Euglenozoa. Jakobids are among a few lineages of nanoflagellates frequently detected in anoxic habitats by PCR-based studies, however only two strains of a single jakobid species have been isolated from those habitats. We recovered 712 environmental sequences and cultured 21 new isolates of anaerobic jakobids that collectively represent at least ten different species in total, from which four are uncultured. Two cultured species have never been detected by environmental, PCR-based methods. Surprisingly, culture-based and culture-independent approaches were able to reveal a relatively high proportion of overall species diversity of anaerobic jakobids - 60 % or 80 %, respectively. Our phylogenetic analyses based on SSU rDNA and six protein-coding genes showed that anaerobic jakobids constitute a clade of morphologically similar, but genetically and ecologically diverse protists – Stygiellidae fam. nov. Our investigation combines culture-based and environmental molecular-based approaches to capture a wider extent of species diversity and shows Stygiellidae as a group that ordinarily inhabits anoxic, sulfide- and ammonium-rich marine habitats worldwide.

  11. Temperature-independent fiber-Bragg-grating-based atmospheric pressure sensor

    Science.gov (United States)

    Zhang, Zhiguo; Shen, Chunyan; Li, Luming

    2018-03-01

    Atmospheric pressure is an important way to achieve a high degree of measurement for modern aircrafts, moreover, it is also an indispensable parameter in the meteorological telemetry system. With the development of society, people are increasingly concerned about the weather. Accurate and convenient atmospheric pressure parameters can provide strong support for meteorological analysis. However, electronic atmospheric pressure sensors currently in application suffer from several shortcomings. After an analysis and discussion, we propose an innovative structural design, in which a vacuum membrane box and a temperature-independent strain sensor based on an equal strength cantilever beam structure and fiber Bragg grating (FBG) sensors are used. We provide experimental verification of that the atmospheric pressure sensor device has the characteristics of a simple structure, lack of an external power supply, automatic temperature compensation, and high sensitivity. The sensor system has good sensitivity, which can be up to 100 nm/MPa, and repeatability. In addition, the device exhibits desired hysteresis.

  12. Action-reaction based parameters identification and states estimation of flexible systems

    OpenAIRE

    Khalil, Islam Shoukry Mohammed; Şabanoviç, Asif; Sabanovic, Asif

    2010-01-01

    This work attempts to identify and estimate flexible system’s parameters and states by a simple utilization of the Action-Reaction law of dynamical systems. Attached actuator to a dynamical system or environmental interaction imposes an action that is instantaneously followed by a dynamical system reaction. The dynamical system’s reaction carries full information about the dynamical system including system parameters, dynamics and externally applied forces that arise due to system interaction...

  13. Complex bifurcation patterns in a discrete predator-prey model with periodic environmental modulation

    Science.gov (United States)

    Harikrishnan, K. P.

    2018-02-01

    We consider the simplest model in the family of discrete predator-prey system and introduce for the first time an environmental factor in the evolution of the system by periodically modulating the natural death rate of the predator. We show that with the introduction of environmental modulation, the bifurcation structure becomes much more complex with bubble structure and inverse period doubling bifurcation. The model also displays the peculiar phenomenon of coexistence of multiple limit cycles in the domain of attraction for a given parameter value that combine and finally gets transformed into a single strange attractor as the control parameter is increased. To identify the chaotic regime in the parameter plane of the model, we apply the recently proposed scheme based on the correlation dimension analysis. We show that the environmental modulation is more favourable for the stable coexistence of the predator and the prey as the regions of fixed point and limit cycle in the parameter plane increase at the expense of chaotic domain.

  14. Media independence and dividend policy

    DEFF Research Database (Denmark)

    Farooq, Omar; Dandoune, Salma

    2012-01-01

    independence and dividend policies in emerging markets. Using a dataset from twenty three emerging markets, we show a significantly negative relationship between dividend policies (payout ratio and decision to pay dividend) and media independence. We argue that independent media reduces information asymmetries...... for stock market participants. Consequently, stock market participants in emerging markets with more independent media do not demand as high and as much dividends as their counterparts in emerging markets with less independent media. We also show that press independence is more important in defining......Can media pressurize managers to disgorge excess cash to shareholders? Do firms in countries with more independent media follow different dividend policies than firms with less independent media? This paper seeks to answer these questions and aims to document the relationship between media...

  15. Predicting genotypes environmental range from genome-environment associations.

    Science.gov (United States)

    Manel, Stéphanie; Andrello, Marco; Henry, Karine; Verdelet, Daphné; Darracq, Aude; Guerin, Pierre-Edouard; Desprez, Bruno; Devaux, Pierre

    2018-05-17

    Genome-environment association methods aim to detect genetic markers associated with environmental variables. The detected associations are usually analysed separately to identify the genomic regions involved in local adaptation. However, a recent study suggests that single-locus associations can be combined and used in a predictive way to estimate environmental variables for new individuals on the basis of their genotypes. Here, we introduce an original approach to predict the environmental range (values and upper and lower limits) of species genotypes from the genetic markers significantly associated with those environmental variables in an independent set of individuals. We illustrate this approach to predict aridity in a database constituted of 950 individuals of wild beets and 299 individuals of cultivated beets genotyped at 14,409 random Single Nucleotide Polymorphisms (SNPs). We detected 66 alleles associated with aridity and used them to calculate the fraction (I) of aridity-associated alleles in each individual. The fraction I correctly predicted the values of aridity in an independent validation set of wild individuals and was then used to predict aridity in the 299 cultivated individuals. Wild individuals had higher median values and a wider range of values of aridity than the cultivated individuals, suggesting that wild individuals have higher ability to resist to stress-aridity conditions and could be used to improve the resistance of cultivated varieties to aridity. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

  16. Deriving global parameter estimates for the Noah land surface model using FLUXNET and machine learning

    Science.gov (United States)

    Chaney, Nathaniel W.; Herman, Jonathan D.; Ek, Michael B.; Wood, Eric F.

    2016-11-01

    With their origins in numerical weather prediction and climate modeling, land surface models aim to accurately partition the surface energy balance. An overlooked challenge in these schemes is the role of model parameter uncertainty, particularly at unmonitored sites. This study provides global parameter estimates for the Noah land surface model using 85 eddy covariance sites in the global FLUXNET network. The at-site parameters are first calibrated using a Latin Hypercube-based ensemble of the most sensitive parameters, determined by the Sobol method, to be the minimum stomatal resistance (rs,min), the Zilitinkevich empirical constant (Czil), and the bare soil evaporation exponent (fxexp). Calibration leads to an increase in the mean Kling-Gupta Efficiency performance metric from 0.54 to 0.71. These calibrated parameter sets are then related to local environmental characteristics using the Extra-Trees machine learning algorithm. The fitted Extra-Trees model is used to map the optimal parameter sets over the globe at a 5 km spatial resolution. The leave-one-out cross validation of the mapped parameters using the Noah land surface model suggests that there is the potential to skillfully relate calibrated model parameter sets to local environmental characteristics. The results demonstrate the potential to use FLUXNET to tune the parameterizations of surface fluxes in land surface models and to provide improved parameter estimates over the globe.

  17. Quantifying the effects of ecological constraints on trait expression using novel trait-gradient analysis parameters.

    Science.gov (United States)

    Ottaviani, Gianluigi; Tsakalos, James L; Keppel, Gunnar; Mucina, Ladislav

    2018-01-01

    Complex processes related to biotic and abiotic forces can impose limitations to assembly and composition of plant communities. Quantifying the effects of these constraints on plant functional traits across environmental gradients, and among communities, remains challenging. We define ecological constraint ( C i ) as the combined, limiting effect of biotic interactions and environmental filtering on trait expression (i.e., the mean value and range of functional traits). Here, we propose a set of novel parameters to quantify this constraint by extending the trait-gradient analysis (TGA) methodology. The key parameter is ecological constraint, which is dimensionless and can be measured at various scales, for example, on population and community levels. It facilitates comparing the effects of ecological constraints on trait expressions across environmental gradients, as well as within and among communities. We illustrate the implementation of the proposed parameters using the bark thickness of 14 woody species along an aridity gradient on granite outcrops in southwestern Australia. We found a positive correlation between increasing environmental stress and strength of ecological constraint on bark thickness expression. Also, plants from more stressful habitats (shrublands on shallow soils and in sun-exposed locations) displayed higher ecological constraint for bark thickness than plants in more benign habitats (woodlands on deep soils and in sheltered locations). The relative ease of calculation and dimensionless nature of C i allow it to be readily implemented at various scales and make it widely applicable. It therefore has the potential to advance the mechanistic understanding of the ecological processes shaping trait expression. Some future applications of the new parameters could be investigating the patterns of ecological constraints (1) among communities from different regions, (2) on different traits across similar environmental gradients, and (3) for the same

  18. Effect of clinical parameters on the control of myoelectric robotic prosthetic hands.

    Science.gov (United States)

    Atzori, Manfredo; Gijsberts, Arjan; Castellini, Claudio; Caputo, Barbara; Hager, Anne-Gabrielle Mittaz; Elsig, Simone; Giatsidis, Giorgio; Bassetto, Franco; Müller, Henning

    2016-01-01

    Improving the functionality of prosthetic hands with noninvasive techniques is still a challenge. Surface electromyography (sEMG) currently gives limited control capabilities; however, the application of machine learning to the analysis of sEMG signals is promising and has recently been applied in practice, but many questions still remain. In this study, we recorded the sEMG activity of the forearm of 11 male subjects with transradial amputation who were mentally performing 40 hand and wrist movements. The classification performance and the number of independent movements (defined as the subset of movements that could be distinguished with >90% accuracy) were studied in relationship to clinical parameters related to the amputation. The analysis showed that classification accuracy and the number of independent movements increased significantly with phantom limb sensation intensity, remaining forearm percentage, and temporal distance to the amputation. The classification results suggest the possibility of naturally controlling up to 11 movements of a robotic prosthetic hand with almost no training. Knowledge of the relationship between classification accuracy and clinical parameters adds new information regarding the nature of phantom limb pain as well as other clinical parameters, and it can lay the foundations for future "functional amputation" procedures in surgery.

  19. Array-Enhanced Coherence Resonance: Nontrivial Effects of Heterogeneity and Spatial Independence of Noise

    International Nuclear Information System (INIS)

    Zhou, Changsong; Kurths, Juergen; Hu, Bambi

    2001-01-01

    We demonstrate the effect of coherence resonance in a heterogeneous array of coupled Fitz Hugh--Nagumo neurons. It is shown that coupling of such elements leads to a significantly stronger coherence compared to that of a single element. We report nontrivial effects of parameter heterogeneity and spatial independence of noise on array-enhanced coherence resonance; especially, we find that (i) the coherence increases as spatial correlation of the noise decreases, and (ii) inhomogeneity in the parameters of the array enhances the coherence. Our results have the implication that generic heterogeneity and background noise can play a constructive role to enhance the time precision of firing in neural systems

  20. Two-group Current-equivalent Parameters for Control Rod Cells. Autocode Programme CRCC

    Energy Technology Data Exchange (ETDEWEB)

    Norinder, O; Nyman, K

    1962-06-15

    In two-group neutron diffusion calculations there is mostly necessary to describe the influence of control rods by equivalent homogeneous two-group parameters in regions about the control rods. The problem is solved for a control rod in a medium characterized by two-group parameters. The property of fast and thermal neutr. on current equivalence is selected to obtain equivalent two-group parameters for a homogeneous cell with the same radius as the control rod cell. For the parameters determined one obtains the same fast and thermal neutron current into the rod cell and the equivalent cell independent of the fast and thermal flux amplitudes on the cell boundaries. The equivalent parameters are obtained as a solution of a system of transcendental equations. A Ferranti Mercury Autocode performing the solution is described. Calculated equivalent parameters for control rods in a heavy water lattice are given for some representative cases.

  1. Nutritional parameters as mortality predictors in haemodialysis: Differences between genders.

    Science.gov (United States)

    Oliveira, Telma Sobral; Valente, Ana Tentúgal; Caetano, Cristina Guerreiro; Garagarza, Cristina Antunes

    2017-06-01

    Malnutrition is common in patients undergoing haemodialysis (HD). Several studies have described different nutritional parameters as mortality predictors but few have studied whether there are differences between genders. This study aimed to evaluate which nutrition parameters may be associated with mortality in patients undergoing long-term HD depending on their gender. Longitudinal prospective multicentre study with 12 months of follow-up. Anthropometric and laboratory measures were obtained from 697 patients. Men who died were older, had lower dry weight, body mass index, potassium, phosphorus and albumin, compared with male patients who survived. Female patients who died had lower albumin and nPCR compared with survivors. Kaplan-Meier analysis displayed a significantly worse survival in patients with albumin mortality was related to body mass index mortality risk continued to be significant after adjustments for age, length of time on dialysis and diabetes for males. However, in women, only albumin persisted as an independent predictor of death. Depending on the gender, different parameters such as protein intake, potassium, phosphorus, body mass index and albumin are associated with mortality in patients undergoing HD. Albumin mortality predictor in both genders, whereas a body mass index <23 kg/m 2 is an independent predictor of death, but only in men. © 2017 European Dialysis and Transplant Nurses Association/European Renal Care Association.

  2. An independent determination of the local Hubble constant

    Science.gov (United States)

    Fernández Arenas, David; Terlevich, Elena; Terlevich, Roberto; Melnick, Jorge; Chávez, Ricardo; Bresolin, Fabio; Telles, Eduardo; Plionis, Manolis; Basilakos, Spyros

    2018-02-01

    The relationship between the integrated H β line luminosity and the velocity dispersion of the ionized gas of H II galaxies and giant H II regions represents an exciting standard candle that presently can be used up to redshifts z ˜ 4. Locally it is used to obtain precise measurements of the Hubble constant by combining the slope of the relation obtained from nearby (z ≤ 0.2) H II galaxies with the zero-point determined from giant H II regions belonging to an `anchor sample' of galaxies for which accurate redshift-independent distance moduli are available. We present new data for 36 giant H II regions in 13 galaxies of the anchor sample that includes the megamaser galaxy NGC 4258. Our data are the result of the first 4 yr of observation of our primary sample of 130 giant H II regions in 73 galaxies with Cepheid determined distances. Our best estimate of the Hubble parameter is 71.0 ± 2.8(random) ± 2.1(systematic) km s- 1Mpc- 1. This result is the product of an independent approach and, although at present less precise than the latest SNIa results, it is amenable to substantial improvement.

  3. Continuity of Genetic and Environmental Influences on Cognition across the Life Span: A Meta-Analysis of Longitudinal Twin and Adoption Studies

    Science.gov (United States)

    Tucker-Drob, Elliot M.; Briley, Daniel A.

    2014-01-01

    The longitudinal rank-order stability of cognitive ability increases dramatically over the lifespan. Multiple theoretical perspectives have proposed that genetic and/or environmental mechanisms underlie the longitudinal stability of cognition, and developmental trends therein. However, the patterns of stability of genetic and environmental influences on cognition over the lifespan largely remain poorly understood. We searched for longitudinal studies of cognition that reported raw genetically-informative longitudinal correlations or parameter estimates from longitudinal behavior genetic models. We identified 150 combinations of time points and measures from 15 independent longitudinal samples. In total, longitudinal data came from 4,538 monozygotic twin pairs raised together, 7,777 dizygotic twin pairs raised together, 34 monozygotic twin pairs raised apart, 78 dizygotic twin pairs raised apart, 141 adoptive sibling pairs, and 143 non-adoptive sibling pairs, ranging in age from infancy through late adulthood. At all ages, cross-time genetic correlations and shared environmental correlations were substantially larger than cross-time nonshared environmental correlations. Cross-time correlations for genetic and shared environmental components were low during early childhood, increased sharply over child development, and remained relatively high from adolescence through late adulthood. Cross-time correlations for nonshared environmental components were low across childhood and increased gradually to moderate magnitudes in adulthood. Increasing phenotypic stability over child development was almost entirely mediated by genetic factors. Time-based decay of genetic and shared environmental stability was more pronounced earlier in child development. Results are interpreted in reference to theories of gene-environment interaction and correlation. PMID:24611582

  4. Analysis of the Relationship Between Physical Environmental Parameters and Beach Water Quality in a Subtropical Setting

    Science.gov (United States)

    Zhu, X.; Wang, J. D.; Elmir, S.; Solo-Gabriele, H. M.; Wright, M. E.; Abdelzaher, A.

    2006-12-01

    Fecal Indicator Bacteria(FIB) are found in high concentrations in sewage water, and thus are used to indicate whether there is fecal material related pathogen present and to determine whether a beach is safe for recreational use. Studies have shown, however, in subtropical regions, FIB concentrations above EPA standards may be present in the absence of known point sources of human or animal waste, thus reducing the efficacy of FIB beach monitoring programs. An interdisciplinary study is being conducted in Miami, Florida , the goal is to understand the sources and behavior of FIB on a beach without point source loads and also to improve beach health hazard warnings in subtropical regions. This study, examines relationship between enterococci (EPA recommended FIB for use in marine water) and physical environmental parameters such as rain, tide and wind. FIB data employed include Florida Department of Health weekly beach monitoring enterococci (ENT) data during a five year period and a two-day experiment with hourly sampling at Hobie Cat Beach on Virginia Key in the Miami metropolitan area. The environmental data consist of wind from a nearby CMAN tower, and local rain and tide. The analysis also includes data from nearby beaches monitored by the Health Department. Results show the correlation coefficient between ENT and tide at Hobie Cat Beach is positive but not significant(r=0.17). Rain events have a significant influence on ENT at Hobie Cat Beach, with a correlation coefficient of up to 0.7 while at other beaches the correlation is less than 0.2. Reasons for this aberration are being investigated. Although this is the only beach allowing dogs there are other factors of possible importance, such as tidal flats frequented by birds and weaker water circulation and exchange at this beach facing a bay rather than the ocean. Higher ENT levels (> 300CFU/100ml water) are more likely (67% of the time) to be associated with periods of onshore winds, which may affect the

  5. Technology management for environmentally sound and sustainable development

    International Nuclear Information System (INIS)

    Zaidi, S.M.J.

    1992-01-01

    With the evolutionary change in the production activities of human societies, the concept of development has also been changing. In the recent years the emphasis has been on the environmentally sound and sustainable development. The environmentally sound and sustainable development can be obtained through judicious use of technology. Technology as a resource transformer has emerged as the most important factor which can constitute to economic growth. But technology is not an independent and autonomous force, it is only an instrument which needs to be used carefully, properly and appropriately which necessitates technology management. (author)

  6. Stochastic Parameter Development for PORFLOW Simulations of the Hanford AX Tank Farm

    International Nuclear Information System (INIS)

    Ho, C.K.; Baca, R.G.; Conrad, S.H.; Smith, G.A.; Shyr, L.; Wheeler, T.A.

    1999-01-01

    Parameters have been identified that can be modeled stochastically using PORFLOW and Latin Hypercube Sampling (LHS). These parameters include hydrologic and transport properties in the vadose and saturated zones, as well as source-term parameters and infiltration rates. A number of resources were used to define the parameter distributions, primarily those provided in the Retrieval Performance Evaluation Report (Jacobs, 1998). A linear rank regression was performed on the vadose-zone hydrologic parameters given in Khaleel and Freeman (1995) to determine if correlations existed between pairs of parameters. No strong correlations were found among the vadose-zone hydrologic parameters, and it was recommended that these parameters be sampled independently until future data or analyses reveal a strong correlation or functional relationship between parameters. Other distributions for source-term parameters, infiltration rates, and saturated-zone parameters that are required to stochastically analyze the performance of the AX Tank Farm using LHS/PORFLOW were adapted from distributions and values reported in Jacobs (1998) and other literature sources. Discussions pertaining to the geologic conceptualization, vadose-zone modeling, and saturated-zone modeling of the AX Tank Farm are also presented

  7. Optimization of reaction parameters of radiation induced grafting of 1-vinylimidazole onto poly(ethylene-co-tetraflouroethene) using response surface method

    Energy Technology Data Exchange (ETDEWEB)

    Nasef, Mohamed Mahmoud, E-mail: mahmoudeithar@fkkksa.utm.my [Institute of Hydrogen Economy, International Campus, Universiti Teknologi Malaysia, 54100 Kuala Lumpur (Malaysia); Aly, Amgad Ahmed; Saidi, Hamdani; Ahmad, Arshad [Institute of Hydrogen Economy, International Campus, Universiti Teknologi Malaysia, 54100 Kuala Lumpur (Malaysia)

    2011-11-15

    Radiation induced grafting of 1-vinylimidazole (1-VIm) onto poly(ethylene-co-tetraflouroethene) (ETFE) was investigated. The grafting parameters such as absorbed dose, monomer concentration, grafting time and temperature were optimized using response surface method (RSM). The Box-Behnken module available in the design expert software was used to investigate the effect of reaction conditions (independent parameters) varied in four levels on the degree of grafting (G%) (response parameter). The model yielded a polynomial equation that relates the linear, quadratic and interaction effects of the independent parameters to the response parameter. The analysis of variance (ANOVA) was used to evaluate the results of the model and detect the significant values for the independent parameters. The optimum parameters to achieve a maximum G% were found to be monomer concentration of 55 vol%, absorbed dose of 100 kGy, time in the range of 14-20 h and a temperature of 61 {sup o}C. Fourier transform infrared (FTIR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were used to investigate the properties of the obtained films and provide evidence for grafting. - Highlights: > A precursor for phosphoric acid membrane for a high temperature PEM fuel cell was prepared. > The grafting parameters for radiation induced grafting of 1-VIm onto ETFE film were optimized. > Surface response method was used to predict the degree of grafting. > The predicted value agreed well with the experimental data as indicated by a 3% deviation. > The number of the experiments and cost of radiation induced grafting were reduced.

  8. A model for rate-dependent but time-independent material behavior in cyclic plasticity

    International Nuclear Information System (INIS)

    Dafalias, Y.F.; Ramey, M.R.; Sheikh, I.

    1977-01-01

    This paper presents a model for rate-dependent but time independent material behavior under cyclic loading in the plastic range. What is referred to as time independent behavior here, is the absence of creep and relaxation phenomena from the behavior of the model. The notion of plastic internal variables (piv) is introduced, as properly invariant scalars or second order tensors, whose constitutive relations are rate-type equations not necessarily homogeneous of order one in the rates, as it would be required for independent plasticity. The concept of a yield surface in the strain space and a loading function in terms of the total strain rate is introduced, where the sign of the loading function defines zero or non-zero value of the rate of piv. Thus rate dependence is achieved without time dependent behaviour (no creep or relaxation). In addition, discrete memory parameters associated with the most recent event of unloading-reloading in different directions enter the constitutive relations for the piv. (Auth.)

  9. Independent validation testing of the FLAME computer code, Version 1.0

    International Nuclear Information System (INIS)

    Martian, P.; Chung, J.N.

    1992-07-01

    Independent testing of the FLAME computer code, Version 1.0, was conducted to determine if the code is ready for use in hydrological and environmental studies at Department of Energy sites. This report describes the technical basis, approach, and results of this testing. Validation tests, (i.e., tests which compare field data to the computer generated solutions) were used to determine the operational status of the FLAME computer code and were done on a qualitative basis through graphical comparisons of the experimental and numerical data. These tests were specifically designed to check: (1) correctness of the FORTRAN coding, (2) computational accuracy, and (3) suitability to simulating actual hydrologic conditions. This testing was performed using a structured evaluation protocol which consisted of: (1) independent applications, and (2) graduated difficulty of test cases. Three tests ranging in complexity from simple one-dimensional steady-state flow field problems under near-saturated conditions to two-dimensional transient flow problems with very dry initial conditions

  10. Environmental risk index: A tool to assess the safety of dams for leachate

    International Nuclear Information System (INIS)

    Colomer Mendoza, Francisco J.; Gallardo Izquierdo, Antonio

    2009-01-01

    Dams for leachate store very toxic substances that contain a large amount of organic material and, probably, heavy metals; they therefore constitute an important threat to the environment. Existing models of environmental risk assessment for landfills do not take into consideration the specific risk that leachate dams may represent for the environment. In this paper a methodology to improve the environmental safety is presented according to the parameters used in their construction and management. In order to do that, the following characteristics of the dam must be known: (1) geotechnical stability, (2) erosion of downstream slope, (3) type of sealing of the dam, (4) overtopping probability, (5) volume of leachate stored inside the dam and (6) pollution load of leachate. Once these parameters have been calculated, they are transformed by means of rating curves into homogeneous units, so as to make it possible to operate between them. From the study and analysis of these parameters an environmental risk index for a dam for leachate can be calculated. If the environmental risk index exceeds an established value then it involves a dam for leachate with high environmental risk, therefore preventive measures in its design, construction and management would be necessary

  11. DIRECTIONAL DEPENDENCE OF ΛCDM COSMOLOGICAL PARAMETERS

    International Nuclear Information System (INIS)

    Axelsson, M.; Fantaye, Y.; Hansen, F. K.; Eriksen, H. K.; Banday, A. J.; Gorski, K. M.

    2013-01-01

    We study hemispherical power asymmetry in the Wilkinson Microwave Anisotropy Probe 9 yr data. We analyze the combined V- and W-band sky maps, after application of the KQ85 mask, and find that the asymmetry is statistically significant at the 3.4σ confidence level for l = 2-600, where the data are signal-dominated, with a preferred asymmetry direction (l, b) = (227, –27). Individual asymmetry axes estimated from six independent multipole ranges are all consistent with this direction. Subsequently, we estimate cosmological parameters on different parts of the sky and show that the parameters A s , n s , and Ω b are the most sensitive to this power asymmetry. In particular, for the two opposite hemispheres aligned with the preferred asymmetry axis, we find n s = 0.959 ± 0.022 and n s = 0.989 ± 0.024, respectively

  12. On the security of semi-device-independent QKD protocols

    Science.gov (United States)

    Chaturvedi, Anubhav; Ray, Maharshi; Veynar, Ryszard; Pawłowski, Marcin

    2018-06-01

    While fully device-independent security in (BB84-like) prepare-and-measure quantum key distribution (QKD) is impossible, it can be guaranteed against individual attacks in a semi-device-independent (SDI) scenario, wherein no assumptions are made on the characteristics of the hardware used except for an upper bound on the dimension of the communicated system. Studying security under such minimal assumptions is especially relevant in the context of the recent quantum hacking attacks wherein the eavesdroppers can not only construct the devices used by the communicating parties but are also able to remotely alter their behavior. In this work, we study the security of a SDIQKD protocol based on the prepare-and-measure quantum implementation of a well-known cryptographic primitive, the random access code (RAC). We consider imperfect detectors and establish the critical values of the security parameters (the observed success probability of the RAC and the detection efficiency) required for guaranteeing security against eavesdroppers with and without quantum memory. Furthermore, we suggest a minimal characterization of the preparation device in order to lower the requirements for establishing a secure key.

  13. Optimal Laser Phototherapy Parameters for Pain Relief.

    Science.gov (United States)

    Kate, Rohit J; Rubatt, Sarah; Enwemeka, Chukuka S; Huddleston, Wendy E

    2018-03-27

    Studies on laser phototherapy for pain relief have used parameters that vary widely and have reported varying outcomes. The purpose of this study was to determine the optimal parameter ranges of laser phototherapy for pain relief by analyzing data aggregated from existing primary literature. Original studies were gathered from available sources and were screened to meet the pre-established inclusion criteria. The included articles were then subjected to meta-analysis using Cohen's d statistic for determining treatment effect size. From these studies, ranges of the reported parameters that always resulted into large effect sizes were determined. These optimal ranges were evaluated for their accuracy using leave-one-article-out cross-validation procedure. A total of 96 articles met the inclusion criteria for meta-analysis and yielded 232 effect sizes. The average effect size was highly significant: d = +1.36 (confidence interval [95% CI] = 1.04-1.68). Among all the parameters, total energy was found to have the greatest effect on pain relief and had the most prominent optimal ranges of 120-162 and 15.36-20.16 J, which always resulted in large effect sizes. The cross-validation accuracy of the optimal ranges for total energy was 68.57% (95% CI = 53.19-83.97). Fewer and less-prominent optimal ranges were obtained for the energy density and duration parameters. None of the remaining parameters was found to be independently related to pain relief outcomes. The findings of meta-analysis indicate that laser phototherapy is highly effective for pain relief. Based on the analysis of parameters, total energy can be optimized to yield the largest effect on pain relief.

  14. Sensitivity analysis of the leaching rate parameter in assessing the environmental risk of phosphogypsum application in sanitary landfills

    Energy Technology Data Exchange (ETDEWEB)

    Marchesi, Marcos Vinicius A.; Hama, Naruhiko; Jacomino, Vanusa M.F.; Ladeira, Ana Claudia Q.; Cota, Stela D.S., E-mail: mvmarchesi@hotmail.com, E-mail: sdsc@cdtn.br, E-mail: vmfj@cdtn.br, E-mail: ana.ladeira@cdtn.br, E-mail: naruhikohama@hotmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2013-07-01

    The attack with sulfuric acid to phosphate rock produces both phosphoric acid, basic raw material in the manufacture of fertilizers, as a by-product called phosphogypsum. Phosphogypsum is composed mostly of calcium sulfate dihydrated, but may have high levels of impurities from the phosphate rock matrix as a series of natural radionuclides, and heavy metals (e.g. Cd, Zn) and metalloids (e.g. , As and Se). Although it is used for agricultural purposes and more recently in construction, in Brazil the generation rate estimated at six million tons per year is much higher than the amount spent on existing alternatives, and therefore mostly deposited in piles in the same place production, causing thereby the risk of contamination of soil and water resources of the region and providing risk to human health. Taken into account the need to find alternative arrangements for phosphogypsum and reduce the impact generated by its contaminants, this study aims to analyze the sensitivity of the leaching rate parameter in the environmental risk evaluation of the application of phosphogypsum in landfills through mathematical modeling, where it is evaluated the concentration of heavy metals and radionuclides in the layer of the soil under the clay layer of the landfill.

  15. Sensitivity analysis of the leaching rate parameter in assessing the environmental risk of phosphogypsum application in sanitary landfills

    International Nuclear Information System (INIS)

    Marchesi, Marcos Vinicius A.; Hama, Naruhiko; Jacomino, Vanusa M.F.; Ladeira, Ana Claudia Q.; Cota, Stela D.S.

    2013-01-01

    The attack with sulfuric acid to phosphate rock produces both phosphoric acid, basic raw material in the manufacture of fertilizers, as a by-product called phosphogypsum. Phosphogypsum is composed mostly of calcium sulfate dihydrated, but may have high levels of impurities from the phosphate rock matrix as a series of natural radionuclides, and heavy metals (e.g. Cd, Zn) and metalloids (e.g. , As and Se). Although it is used for agricultural purposes and more recently in construction, in Brazil the generation rate estimated at six million tons per year is much higher than the amount spent on existing alternatives, and therefore mostly deposited in piles in the same place production, causing thereby the risk of contamination of soil and water resources of the region and providing risk to human health. Taken into account the need to find alternative arrangements for phosphogypsum and reduce the impact generated by its contaminants, this study aims to analyze the sensitivity of the leaching rate parameter in the environmental risk evaluation of the application of phosphogypsum in landfills through mathematical modeling, where it is evaluated the concentration of heavy metals and radionuclides in the layer of the soil under the clay layer of the landfill

  16. The importance of board independence

    NARCIS (Netherlands)

    Zijl, N.J.M.

    2012-01-01

    Although the attributed importance of board independence is high, a clear definition of independence does not exist. Furthermore, the aim and consequences of independence are the subject of discussion and empirical evidence about the impact of independence is weak and disputable. Despite this lack

  17. Evaluation of the strain rate effects on environmental fatigue life of CF8M cast stainless steel

    International Nuclear Information System (INIS)

    Jeong, Ill Seok; Ha, Gak Hyun; Jeon, Hyun Ik

    2009-01-01

    The environmental fatigue life of CF8M cast stainless steel is influenced by mechanical, environmental and metallurgical parameters, such as strain rate, strain amplitude, temperature, dissolved oxygen concentration, water flow rate and so on. In an actual plant, the mechanical and environmental parameters are changing during the plant operation. Therefore, the effect of such mechanical and environmental parameter changes on fatigue life evaluation have to be studied. Low cycle fatigue life of structural materials diminishes remarkably as functions of various parameters in high temperature and high pressure environments. Such reduction can be estimated by the fatigue life reduction factor(F en ). In this study, fatigue tests were performed under changing conditions of strain amplitude, strain rate. Fatigue life was measured in terms of the number of cycles with the variation of strain amplitudes at 0.004 %/s strain rate, and the fatigue life correction factor was evaluated according to the equation modified by U. S. Nuclear Regulatory Commission(U.S.NRC) and Japanese Environmental Fatigue Tests committee (JEFT).

  18. A K-means multivariate approach for clustering independent components from magnetoencephalographic data.

    Science.gov (United States)

    Spadone, Sara; de Pasquale, Francesco; Mantini, Dante; Della Penna, Stefania

    2012-09-01

    Independent component analysis (ICA) is typically applied on functional magnetic resonance imaging, electroencephalographic and magnetoencephalographic (MEG) data due to its data-driven nature. In these applications, ICA needs to be extended from single to multi-session and multi-subject studies for interpreting and assigning a statistical significance at the group level. Here a novel strategy for analyzing MEG independent components (ICs) is presented, Multivariate Algorithm for Grouping MEG Independent Components K-means based (MAGMICK). The proposed approach is able to capture spatio-temporal dynamics of brain activity in MEG studies by running ICA at subject level and then clustering the ICs across sessions and subjects. Distinctive features of MAGMICK are: i) the implementation of an efficient set of "MEG fingerprints" designed to summarize properties of MEG ICs as they are built on spatial, temporal and spectral parameters; ii) the implementation of a modified version of the standard K-means procedure to improve its data-driven character. This algorithm groups the obtained ICs automatically estimating the number of clusters through an adaptive weighting of the parameters and a constraint on the ICs independence, i.e. components coming from the same session (at subject level) or subject (at group level) cannot be grouped together. The performances of MAGMICK are illustrated by analyzing two sets of MEG data obtained during a finger tapping task and median nerve stimulation. The results demonstrate that the method can extract consistent patterns of spatial topography and spectral properties across sessions and subjects that are in good agreement with the literature. In addition, these results are compared to those from a modified version of affinity propagation clustering method. The comparison, evaluated in terms of different clustering validity indices, shows that our methodology often outperforms the clustering algorithm. Eventually, these results are

  19. Fish bioaccumulation and biomarkers in environmental risk assessment: a review.

    Science.gov (United States)

    van der Oost, Ron; Beyer, Jonny; Vermeulen, Nico P E

    2003-02-01

    In this review, a wide array of bioaccumulation markers and biomarkers, used to demonstrate exposure to and effects of environmental contaminants, has been discussed in relation to their feasibility in environmental risk assessment (ERA). Fish bioaccumulation markers may be applied in order to elucidate the aquatic behavior of environmental contaminants, as bioconcentrators to identify certain substances with low water levels and to assess exposure of aquatic organisms. Since it is virtually impossible to predict the fate of xenobiotic substances with simple partitioning models, the complexity of bioaccumulation should be considered, including toxicokinetics, metabolism, biota-sediment accumulation factors (BSAFs), organ-specific bioaccumulation and bound residues. Since it remains hard to accurately predict bioaccumulation in fish, even with highly sophisticated models, analyses of tissue levels are required. The most promising fish bioaccumulation markers are body burdens of persistent organic pollutants, like PCBs and DDTs. Since PCDD and PCDF levels in fish tissues are very low as compared with the sediment levels, their value as bioaccumulation markers remains questionable. Easily biodegradable compounds, such as PAHs and chlorinated phenols, do not tend to accumulate in fish tissues in quantities that reflect the exposure. Semipermeable membrane devices (SPMDs) have been successfully used to mimic bioaccumulation of hydrophobic organic substances in aquatic organisms. In order to assess exposure to or effects of environmental pollutants on aquatic ecosystems, the following suite of fish biomarkers may be examined: biotransformation enzymes (phase I and II), oxidative stress parameters, biotransformation products, stress proteins, metallothioneins (MTs), MXR proteins, hematological parameters, immunological parameters, reproductive and endocrine parameters, genotoxic parameters, neuromuscular parameters, physiological, histological and morphological parameters

  20. Generation of a library of two-group diffusion and kinetics parameters for DYN3D

    International Nuclear Information System (INIS)

    Petkov, P.T.; Christoskov, I.D.; Kamenov, K.; Antov, A.

    2002-01-01

    A library of two-group diffusion and kinetics parameters has been generated for the neutron kinetics code DYN3D for analysis of reactivity initiated accidents for the WWER-440 reactors, based on the MAGRU approximation methodology for the diffusion and kinetics parameters. The accuracy of this methodology has been tested and the conclusion is that it is not adequate. A new approximation methodology, based on interpolation for the most widely varying parameters, i.e. the moderator temperature and density, and on approximation for all other independent parameters, is presented. The methodology of calculation of the kinetics parameters using primary data from ENDF-B/VI is described in detail (Authors)

  1. Multi objective optimization model for minimizing production cost and environmental impact in CNC turning process

    Science.gov (United States)

    Widhiarso, Wahyu; Rosyidi, Cucuk Nur

    2018-02-01

    Minimizing production cost in a manufacturing company will increase the profit of the company. The cutting parameters will affect total processing time which then will affect the production cost of machining process. Besides affecting the production cost and processing time, the cutting parameters will also affect the environment. An optimization model is needed to determine the optimum cutting parameters. In this paper, we develop an optimization model to minimize the production cost and the environmental impact in CNC turning process. The model is used a multi objective optimization. Cutting speed and feed rate are served as the decision variables. Constraints considered are cutting speed, feed rate, cutting force, output power, and surface roughness. The environmental impact is converted from the environmental burden by using eco-indicator 99. Numerical example is given to show the implementation of the model and solved using OptQuest of Oracle Crystal Ball software. The results of optimization indicate that the model can be used to optimize the cutting parameters to minimize the production cost and the environmental impact.

  2. Minimal parameter solution of the orthogonal matrix differential equation

    Science.gov (United States)

    Bar-Itzhack, Itzhack Y.; Markley, F. Landis

    1990-01-01

    As demonstrated in this work, all orthogonal matrices solve a first order differential equation. The straightforward solution of this equation requires n sup 2 integrations to obtain the element of the nth order matrix. There are, however, only n(n-1)/2 independent parameters which determine an orthogonal matrix. The questions of choosing them, finding their differential equation and expressing the orthogonal matrix in terms of these parameters are considered. Several possibilities which are based on attitude determination in three dimensions are examined. It is shown that not all 3-D methods have useful extensions to higher dimensions. It is also shown why the rate of change of the matrix elements, which are the elements of the angular rate vector in 3-D, are the elements of a tensor of the second rank (dyadic) in spaces other than three dimensional. It is proven that the 3-D Gibbs vector (or Cayley Parameters) are extendable to other dimensions. An algorithm is developed emplying the resulting parameters, which are termed Extended Rodrigues Parameters, and numerical results are presented of the application of the algorithm to a fourth order matrix.

  3. Cosmological parameters from CMB and other data: A Monte Carlo approach

    International Nuclear Information System (INIS)

    Lewis, Antony; Bridle, Sarah

    2002-01-01

    We present a fast Markov chain Monte Carlo exploration of cosmological parameter space. We perform a joint analysis of results from recent cosmic microwave background (CMB) experiments and provide parameter constraints, including σ 8 , from the CMB independent of other data. We next combine data from the CMB, HST Key Project, 2dF galaxy redshift survey, supernovae type Ia and big-bang nucleosynthesis. The Monte Carlo method allows the rapid investigation of a large number of parameters, and we present results from 6 and 9 parameter analyses of flat models, and an 11 parameter analysis of non-flat models. Our results include constraints on the neutrino mass (m ν < or approx. 3 eV), equation of state of the dark energy, and the tensor amplitude, as well as demonstrating the effect of additional parameters on the base parameter constraints. In a series of appendixes we describe the many uses of importance sampling, including computing results from new data and accuracy correction of results generated from an approximate method. We also discuss the different ways of converting parameter samples to parameter constraints, the effect of the prior, assess the goodness of fit and consistency, and describe the use of analytic marginalization over normalization parameters

  4. Parameters Estimation of Geographically Weighted Ordinal Logistic Regression (GWOLR) Model

    Science.gov (United States)

    Zuhdi, Shaifudin; Retno Sari Saputro, Dewi; Widyaningsih, Purnami

    2017-06-01

    A regression model is the representation of relationship between independent variable and dependent variable. The dependent variable has categories used in the logistic regression model to calculate odds on. The logistic regression model for dependent variable has levels in the logistics regression model is ordinal. GWOLR model is an ordinal logistic regression model influenced the geographical location of the observation site. Parameters estimation in the model needed to determine the value of a population based on sample. The purpose of this research is to parameters estimation of GWOLR model using R software. Parameter estimation uses the data amount of dengue fever patients in Semarang City. Observation units used are 144 villages in Semarang City. The results of research get GWOLR model locally for each village and to know probability of number dengue fever patient categories.

  5. Cardiac dysfunction assessed by echocardiographic tissue Doppler imaging is an independent predictor of mortality in the general population

    DEFF Research Database (Denmark)

    Mogelvang, Rasmus; Sogaard, Peter; Pedersen, Sune A

    2009-01-01

    parameters, left ventricular dysfunction by TDI is a powerful and independent predictor of death, especially when systolic performance and diastolic performance are considered together, recognizing their interdependency and their complex relation to deteriorating cardiac function....

  6. Modifying factors for metabolic parameters

    International Nuclear Information System (INIS)

    Inaba, Jiro

    1990-01-01

    Studies on factors which influence the metabolic parameter for calculation of radiation doses from intakes of radionuclides are very important for estimation of the doses for the general public, because the present procedures recommended by the International Commission on Radiological Protection is for occupationally exposed workers and the underlying metabolic and dosimetric models have been developed from studies on adult man and experiments on adult animals and from observations on radionuclides in physico-chemically simple form. Many factors have been reported to influence the metabolic parameters. Among them, the food-chain involvement of radionuclides and the age-dependence in humans and animals are most significant as environmental and physiological factor, respectively. In connection with the age-dependence of dose calculation, the ICRP started a new programme. They organized a Task Group on Age-Dependent Dose-Factors where relevant information on metabolic and biokinetic parameters are presently being reviewed for development of a set of dose factors for the following age-groups: infant, 1-year-old, 5-year-old, 10-year-old, 15-year-old, and ICRP Reference Man. The first stage of the work is for age-dependent integrated organ and effective dose factors for radioisotopes of the following elements: hydrogen, carbon, iodine, cesium, strontium, plutonium and americium. (author)

  7. Independent environmental audit at COPENE (Petrochemical Company of Northeast, Brazil): first results of a partnership

    Energy Technology Data Exchange (ETDEWEB)

    Abreu Pereira, Vera L. de [Companhia Petroquimica do Nordeste (COPENE), Camacari, BA (Brazil). Div. de Engenharia Ambiental

    1994-12-31

    This paper presents the first experiences and results in the implementation of a pioneer model in environmental monitoring of a Brazilian companies consortium, for wastewater and groundwater monitoring. Some practical results, such as the flow reduction in the organic wastewaters and organic load in the final effluents, were obtained in the very first year of activities. 4 refs., 8 figs.

  8. Independent environmental audit at COPENE (Petrochemical Company of Northeast, Brazil): first results of a partnership

    Energy Technology Data Exchange (ETDEWEB)

    Abreu Pereira, Vera L. de [Companhia Petroquimica do Nordeste (COPENE), Camacari, BA (Brazil). Div. de Engenharia Ambiental

    1993-12-31

    This paper presents the first experiences and results in the implementation of a pioneer model in environmental monitoring of a Brazilian companies consortium, for wastewater and groundwater monitoring. Some practical results, such as the flow reduction in the organic wastewaters and organic load in the final effluents, were obtained in the very first year of activities. 4 refs., 8 figs.

  9. Evaluation of selected parameters on exposure rates in Westinghouse designed nuclear power plants

    International Nuclear Information System (INIS)

    Bergmann, C.A.

    1989-01-01

    During the past ten years, Westinghouse under EPRI contract and independently, has performed research and evaluation of plant data to define the trends of ex-core component exposure rates and the effects of various parameters on the exposure rates. The effects of the parameters were evaluated using comparative analyses or empirical techniques. This paper updates the information presented at the Fourth Bournemouth Conference and the conclusions obtained from the effects of selected parameters namely, coolant chemistry, physical changes, use of enriched boric acid, and cobalt input on plant exposure rates. The trends of exposure rates and relationship to doses is also presented. (author)

  10. Environmental parameters and antimicrobial susceptibility of enterobacteriaceae isolated from estuarine waters of São Vicente, São Paulo state, Brazil

    Directory of Open Access Journals (Sweden)

    N. G. G. S. Lourenço

    2007-01-01

    Full Text Available Diseases transmitted by water consists a serious public health problem and enterobacteria are the main group of microorganisms responsible for outbreaks in humans. Such pathogenic bacteria proliferate in water polluted by domestic and industrial sewage and reach the population through seawater contact. The aim of the present work was to study environmental parameters as well as to identify Enterobacteriaceae species and their antimicrobial susceptibility in water samples collected from the estuarine area of São Vicente city (São Paulo State, Brazil. Strains were identified by using traditional biochemical tests described in literature and antimicrobial susceptibility tests were carried out using the disk diffusion method. Out of 26 samples, Escherichia coli was the most frequent species (40.1%, followed by Citrobacter, Enterobacter and Klebsiella. The most effective drugs against the tested microorganisms were gentamycin, netilmicin, ciprofloxacin and cefepime. Since these bacteria are commonly found in seashore contaminated by sewage effluents, it can be concluded that estuarine waters of São Vicente are polluted and potentially capable of causing diseases and spreading pathogenic bacteria to human communities.

  11. Correlates of children's independent outdoor play: Cross-sectional analyses from the Millennium Cohort Study

    Directory of Open Access Journals (Sweden)

    Daniel Aggio

    2017-12-01

    Full Text Available Time spent outdoors is associated with higher levels of physical activity. To date, correlates of independent outdoor play have not been investigated. This study aimed to identify potential demographic, behavioural, environmental and social correlates of children's independent outdoor play.Data were from the Millennium Cohort Study when children were aged 7years. Parents reported whether their children played out unsupervised (yes/no as well as the above mentioned correlates of unsupervised outdoor play. Children's physical activity levels were measured using waist worn accelerometry. Multiple logistic regression was used to examine associations between correlates and odds of independent (unsupervised outdoor play. Adjusted multiple linear regression was used to estimate associations between independent outdoor play and objective measures of physical activity. Activity was measured as average daily moderate-to-vigorous activity, steps, and sedentary behaviour.3856 (n=29% participants were categorised as engaging in independent outdoor play. Older age, being white British, being in poverty, living in close proximity to both family friends and family, having fewer internalising problems, having more externalising conduct problems and fewer pro-social behaviours were associated with higher odds of independent outdoor play. Independent outdoor play was associated with >2 additional minutes of moderate-to-vigorous activity (B=2.21 95% CI, 1.09 to 3.34, >330 additional steps per day (B=336.66 95% CI 209.80 to 463.51, and nearly 5min less time spent sedentary per day (B=−4.91 95% CI −7.54, −2.29Younger children, those from a higher socio-economic-status, those isolated in location from family friends and family, and those with high levels of prosocial behaviour have lower levels of independent outdoor play. Independent outdoor play was associated with higher levels of physical activity and less time sedentary. Future interventions to promote

  12. Smart Sensing Technology for Agriculture and Environmental Monitoring

    CERN Document Server

    2012-01-01

    The book focuses on the different aspects of sensing technology, i.e. high reliability, adaptability, recalibration, information processing, data fusion, validation and integration of novel and high performance sensors specifically aims to monitor agricultural and environmental parameters.   This book is dedicated to Sensing systems for Agricultural and Environmental Monitoring  offers to variety of users, namely, Master and PhD degree students, researchers, practitioners, especially Agriculture and Environmental engineers. The book will provide an opportunity of a dedicated and a deep approach in order to improve their knowledge in this specific field.

  13. The problem of principal chiral field with the parameters depending on free arguments and its integration

    International Nuclear Information System (INIS)

    Aliev, B.N.; Leznov, A.N.

    1989-01-01

    A method to determine the solutions for principal chiral field (PCP) equation with the parameters depending on independent arguments for arbitrary semisimple algebra is worked out. Each solution depends on N(G)-r/2 arbitrary functions of independent arguments. Moreover, the number of derivatives of the arbitrary functions appearing in the solution distinguishes them, gathering them into series. 6 refs

  14. Land And Water Use Characteristics And Human Health Input Parameters For Use In Environmental Dosimetry And Risk Assessments At The Savannah River Site

    International Nuclear Information System (INIS)

    Jannik, T.; Karapatakis, D.; Lee, P.; Farfan, E.

    2010-01-01

    Operations at the Savannah River Site (SRS) result in releases of small amounts of radioactive materials to the atmosphere and to the Savannah River. For regulatory compliance purposes, potential offsite radiological doses are estimated annually using computer models that follow U.S. Nuclear Regulatory Commission (NRC) Regulatory Guides. Within the regulatory guides, default values are provided for many of the dose model parameters but the use of site-specific values by the applicant is encouraged. A detailed survey of land and water use parameters was conducted in 1991 and is being updated here. These parameters include local characteristics of meat, milk and vegetable production; river recreational activities; and meat, milk and vegetable consumption rates as well as other human usage parameters required in the SRS dosimetry models. In addition, the preferred elemental bioaccumulation factors and transfer factors to be used in human health exposure calculations at SRS are documented. Based on comparisons to the 2009 SRS environmental compliance doses, the following effects are expected in future SRS compliance dose calculations: (1) Aquatic all-pathway maximally exposed individual doses may go up about 10 percent due to changes in the aquatic bioaccumulation factors; (2) Aquatic all-pathway collective doses may go up about 5 percent due to changes in the aquatic bioaccumulation factors that offset the reduction in average individual water consumption rates; (3) Irrigation pathway doses to the maximally exposed individual may go up about 40 percent due to increases in the element-specific transfer factors; (4) Irrigation pathway collective doses may go down about 50 percent due to changes in food productivity and production within the 50-mile radius of SRS; (5) Air pathway doses to the maximally exposed individual may go down about 10 percent due to the changes in food productivity in the SRS area and to the changes in element-specific transfer factors; and (6

  15. LAND AND WATER USE CHARACTERISTICS AND HUMAN HEALTH INPUT PARAMETERS FOR USE IN ENVIRONMENTAL DOSIMETRY AND RISK ASSESSMENTS AT THE SAVANNAH RIVER SITE

    Energy Technology Data Exchange (ETDEWEB)

    Jannik, T.; Karapatakis, D.; Lee, P.; Farfan, E.

    2010-08-06

    Operations at the Savannah River Site (SRS) result in releases of small amounts of radioactive materials to the atmosphere and to the Savannah River. For regulatory compliance purposes, potential offsite radiological doses are estimated annually using computer models that follow U.S. Nuclear Regulatory Commission (NRC) Regulatory Guides. Within the regulatory guides, default values are provided for many of the dose model parameters but the use of site-specific values by the applicant is encouraged. A detailed survey of land and water use parameters was conducted in 1991 and is being updated here. These parameters include local characteristics of meat, milk and vegetable production; river recreational activities; and meat, milk and vegetable consumption rates as well as other human usage parameters required in the SRS dosimetry models. In addition, the preferred elemental bioaccumulation factors and transfer factors to be used in human health exposure calculations at SRS are documented. Based on comparisons to the 2009 SRS environmental compliance doses, the following effects are expected in future SRS compliance dose calculations: (1) Aquatic all-pathway maximally exposed individual doses may go up about 10 percent due to changes in the aquatic bioaccumulation factors; (2) Aquatic all-pathway collective doses may go up about 5 percent due to changes in the aquatic bioaccumulation factors that offset the reduction in average individual water consumption rates; (3) Irrigation pathway doses to the maximally exposed individual may go up about 40 percent due to increases in the element-specific transfer factors; (4) Irrigation pathway collective doses may go down about 50 percent due to changes in food productivity and production within the 50-mile radius of SRS; (5) Air pathway doses to the maximally exposed individual may go down about 10 percent due to the changes in food productivity in the SRS area and to the changes in element-specific transfer factors; and (6

  16. Environmental economic impact assessment in China: Problems and prospects

    International Nuclear Information System (INIS)

    Lindhjem, Henrik; Hu Tao; Ma Zhong; Skjelvik, John Magne; Song Guojun; Vennemo, Haakon; Wu Jian; Zhang Shiqiu

    2007-01-01

    The use of economic valuation methods to assess environmental impacts of projects and policies has grown considerably in recent years. However, environmental valuation appears to have developed independently of regulations and practice of environmental impact assessment (EIA), despite its potential benefits to the EIA process. Environmental valuation may be useful in judging significance of impacts, determining mitigation level, comparing alternatives and generally enabling a more objective analysis of tradeoffs. In China, laws and regulations require the use of environmental valuation in EIA, but current practice lags far behind. This paper assesses the problems and prospects of introducing environmental valuation into the EIA process in China. We conduct four case studies of environmental economic impact assessment (EEIA), three of which are based on environmental impact statements of construction projects (a power plant, a wastewater treatment plant and a road construction project) and one for a regional pollution problem (wastewater irrigation). The paper demonstrates the potential usefulness of environmental valuation but also discusses several challenges to the introduction and wider use of EEIA, many of which are likely to be of relevance far beyond the Chinese context. The paper closes with suggesting some initial core elements of an EEIA guideline

  17. Parallel Array Bistable Stochastic Resonance System with Independent Input and Its Signal-to-Noise Ratio Improvement

    Directory of Open Access Journals (Sweden)

    Wei Li

    2014-01-01

    with independent components and averaged output; second, we give a deduction of the output signal-to-noise ratio (SNR for this system to show the performance. Our examples show the enhancement of the system and how different parameters influence the performance of the proposed parallel array.

  18. Towards automated diffraction tomography. Part II-Cell parameter determination

    International Nuclear Information System (INIS)

    Kolb, U.; Gorelik, T.; Otten, M.T.

    2008-01-01

    Automated diffraction tomography (ADT) allows the collection of three-dimensional (3d) diffraction data sets from crystals down to a size of only few nanometres. Imaging is done in STEM mode, and diffraction data are collected with quasi-parallel beam nanoelectron diffraction (NED). Here, we present a set of developed processing steps necessary for automatic unit-cell parameter determination from the collected 3d diffraction data. Cell parameter determination is done via extraction of peak positions from a recorded data set (called the data reduction path) followed by subsequent cluster analysis of difference vectors. The procedure of lattice parameter determination is presented in detail for a beam-sensitive organic material. Independently, we demonstrate a potential (called the full integration path) based on 3d reconstruction of the reciprocal space visualising special structural features of materials such as partial disorder. Furthermore, we describe new features implemented into the acquisition part

  19. Fiber optic sensors for environmental applications: A brief review

    International Nuclear Information System (INIS)

    Rossabi, J.

    1992-04-01

    Understanding the flow a groundwater quality. This understanding is achieved by measurement of the appropriate chemical and physical subsurface parameters. The ideal measurement would accurately assess a parameter without affecting the parameter or its environment. Fiber optic spectroscopy offers some of the most promising techniques for accurate, non-invasive measurements of environmental parameters. Fiber optic sensors for subsurface applications are currently being developed by several Department of Energy laboratories. Some of these sensors have been successfully deployed in the field and are attaining the goals of accurate, noninvasive, real time measurements in the subsurface

  20. 78 FR 40200 - Duke Energy Carolinas, LLC, Oconee Nuclear Station Units 1, 2, and 3; Independent Spent Fuel...

    Science.gov (United States)

    2013-07-03

    ... NUCLEAR REGULATORY COMMISSION [Docket Nos. 72-1004, 72-40, 50-269, 50-270, and 50-287; NRC-2013-0135] Duke Energy Carolinas, LLC, Oconee Nuclear Station Units 1, 2, and 3; Independent Spent Fuel Storage Installation; Environmental Assessment and Finding of No Significant Impact AGENCY: Nuclear...