WorldWideScience

Sample records for included lime softening

  1. Arsenic removal by lime softening

    DEFF Research Database (Denmark)

    Kaosol, T.; Suksaroj, C.; Bregnhøj, Henrik

    2002-01-01

    This paper focuses on the study of arsenic removal for drinking water by lime softening. The initial arsenic (V) concentration was 500 and 1,000 ug/L in synthetic groundwater. The experiments were performed as batch tests with varying lime dosages and mixing time. For the synthetic groundwater......, arsenic (V) removal increased with increasing lime dosage and mixing time, as well as with the resulting pH. The residual arsenic (V) in all cases was lower than the WHO guideline of 10 ug/L at pH higher than 11.5. Kinetic of arsenic (V) removal can be described by a first-order equation as C1 = C0*e......^-k*t. The relation between the constant (k value) and increasing lime dosage was found to be linear, described by k = 0.0034 (Dlime). The results support a theory from the literature that the arsenic (V) was removed by precipitation af Ca3(AsO4)2. The results obtained in the present study suggest that lime...

  2. Evaluation of the impact of lime softening waste disposal in ...

    Science.gov (United States)

    Drinking water treatment residues (WTR), generated from the lime softening processes, are commonly reused or disposed of in a number of applications; these include use as a soil amendment or a subsurface fill. Recently questions were posed by the Florida regulatory community on whether lime WTR that contained a small percentage of other treatment additives could appropriately be characterized as lime WTR, in terms of its total element content and leachability. A study was done using a broad range of leaching tests, including a framework of tests recently adopted by the United States-Environmental Protection Agency (EPA) and tests that were modified to account for scenario specific conditions, such as the presence of natural organic matter (NOM). The results of these additional leaching tests demonstrated that certain applications, including disposal in a water body with NOM or in placement anaerobic environment, did result in increased leaching of elements such as Fe, and that a site specific assessment should be conducted prior to using WTR in these types of applications. This study illustrates the importance of leaching test selection when attempting to provide an estimation of release in practice. Although leaching tests are just one component in a beneficial use assessment and other factors including aquifer and soil properties play a significant role in the outcome, leaching tests should be tailored to most appropriately represent the scenario or reuse ap

  3. REMOVAL OF BERYLLIUM FROM DRINKING WATER BY CHEMICAL COAGULATION AND LIME SOFTENING

    Science.gov (United States)

    The effectiveness of conventional drinking water treatment and lime softening was evaluated for beryllium removal from two drinking water sources. ar test studies were conducted to determine how common coagulants (aluminum sulfate and ferric chloride and lime softening performed ...

  4. Evaluation of the impact of lime softening waste disposal in natural environments

    Science.gov (United States)

    Drinking water treatment residues (WTR), generated from the lime softening processes, are commonly reused or disposed of in a number of applications; these include use as a soil amendment or a subsurface fill. Recently questions were posed by the Florida regulatory community on w...

  5. A novel eco-friendly technique for efficient control of lime water softening process.

    Science.gov (United States)

    Ostovar, Mohamad; Amiri, Mohamad

    2013-12-01

    Lime softening is an established type of water treatment used for water softening. The performance of this process is highly dependent on lime dosage. Currently, lime dosage is adjusted manually based on chemical tests, aimed at maintaining the phenolphthalein (P) and total (M) alkalinities within a certain range (2 P - M > or = 5). In this paper, a critical study of the softening process has been presented. It has been shown that the current method is frequently incorrect. Furthermore, electrical conductivity (EC) has been introduced as a novel indicator for effectively characterizing the lime softening process.This novel technique has several advantages over the current alkalinities method. Because no chemical reagents are needed for titration, which is a simple test, there is a considerable reduction in test costs. Additionally, there is a reduction in the treated water hardness and generated sludge during the lime softening process. Therefore, it is highly eco-friendly, and is a very cost effective alternative technique for efficient control of the lime softening process.

  6. 40 CFR 141.553 - My system practices lime softening-is there any special provision regarding my combined filter...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false My system practices lime softening-is... Filter Effluent Requirements § 141.553 My system practices lime softening—is there any special provision regarding my combined filter effluent? If your system practices lime softening, you may acidify...

  7. ARSENIC REMOVAL FROM DRINKING WATER BY COAGULATION/FILTRATION AND LIME SOFTENING PLANTS

    Science.gov (United States)

    This report documents a long term performance (one year) study of 3 water treatment plants to remove arsenic from drinking water sources. The 3 plants consisted of 2 conventional coagulation/filtration plants and 1 lime softening plant. The study involved the collecting of weekly...

  8. 40 CFR 141.564 - My system practices lime softening-is there any special provision regarding my individual filter...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false My system practices lime softening-is... People Individual Filter Turbidity Requirements § 141.564 My system practices lime softening—is there any special provision regarding my individual filter turbidity monitoring? If your system utilizes lime...

  9. Evaluation of the impact of lime softening waste disposal in natural environments

    International Nuclear Information System (INIS)

    Blaisi, Nawaf I.; Roessler, Justin; Cheng, Weizhi; Townsend, Timothy; Al-Abed, Souhail R.

    2015-01-01

    Highlights: • Leaching tests conducted on WTR to assess potential for trace element release. • Aluminum leaching found to be elevated with respect to risk threshold. • Release in anaerobic conditions evaluated with column test run in nitrogen chamber. • Increased release of certain elements seen from residues under anaerobic conditions. • Different leaching tests produced results on two sides of regulatory threshold. - Abstract: Drinking water treatment residues (WTR), generated from the lime softening processes, are commonly reused or disposed of in a number of applications; these include use as a soil amendment or a subsurface fill. Recently questions were posed by the Florida regulatory community on whether lime WTR that contained a small percentage of other treatment additives could appropriately be characterized as lime WTR, in terms of total element content and leachability. A study was done using a broad range of leaching tests, including a framework of tests recently adopted by the United States-Environmental Protection Agency (EPA) and tests that were modified to account for scenario specific conditions, such as the presence of natural organic matter (NOM). The results of these additional leaching tests demonstrated that certain applications, including disposal in a water body with NOM or in placement anaerobic environment, did result in increased leaching of elements such as Fe, and that a site specific assessment should be conducted prior to using WTR in these types of applications. This study illustrates the importance of leaching test selection when attempting to provide an estimation of release in practice. Although leaching tests are just one component in a beneficial use assessment and other factors including aquifer and soil properties play a significant role in the outcome, leaching tests should be tailored to most appropriately represent the scenario or reuse application being evaluated

  10. Evaluation of the impact of lime softening waste disposal in natural environments

    Energy Technology Data Exchange (ETDEWEB)

    Blaisi, Nawaf I.; Roessler, Justin; Cheng, Weizhi [Department of Environmental Engineering Sciences, University of Florida, PO Box 116450, Gainesville, FL 32611-6450 (United States); Townsend, Timothy, E-mail: ttown@ufl.edu [Department of Environmental Engineering Sciences, University of Florida, PO Box 116450, Gainesville, FL 32611-6450 (United States); Al-Abed, Souhail R. [National Risk Management Research Laboratory, U.S. Environmental Protection Agency, 26 West Martin Luther King Drive, Cincinnati, OH 45268 (United States)

    2015-09-15

    Highlights: • Leaching tests conducted on WTR to assess potential for trace element release. • Aluminum leaching found to be elevated with respect to risk threshold. • Release in anaerobic conditions evaluated with column test run in nitrogen chamber. • Increased release of certain elements seen from residues under anaerobic conditions. • Different leaching tests produced results on two sides of regulatory threshold. - Abstract: Drinking water treatment residues (WTR), generated from the lime softening processes, are commonly reused or disposed of in a number of applications; these include use as a soil amendment or a subsurface fill. Recently questions were posed by the Florida regulatory community on whether lime WTR that contained a small percentage of other treatment additives could appropriately be characterized as lime WTR, in terms of total element content and leachability. A study was done using a broad range of leaching tests, including a framework of tests recently adopted by the United States-Environmental Protection Agency (EPA) and tests that were modified to account for scenario specific conditions, such as the presence of natural organic matter (NOM). The results of these additional leaching tests demonstrated that certain applications, including disposal in a water body with NOM or in placement anaerobic environment, did result in increased leaching of elements such as Fe, and that a site specific assessment should be conducted prior to using WTR in these types of applications. This study illustrates the importance of leaching test selection when attempting to provide an estimation of release in practice. Although leaching tests are just one component in a beneficial use assessment and other factors including aquifer and soil properties play a significant role in the outcome, leaching tests should be tailored to most appropriately represent the scenario or reuse application being evaluated.

  11. Synthetic Musk Fragrances in a Conventional Drinking Water Treatment Plant with Lime Softening

    OpenAIRE

    Wombacher, William D.; Hornbuckle, Keri C.

    2009-01-01

    Synthetic musk fragrances are common personal care product additives and wastewater contaminants that are routinely detected in the environment. This study examines the presence eight synthetic musk fragrances (AHTN, HHCB, ATII, ADBI, AHMI, musk xylene, and musk ketone) in source water and the removal of these compounds as they flow through a Midwestern conventional drinking water plant with lime softening. The compounds were measured in water, waste sludge, and air throughout the plant. HHCB...

  12. Synthetic Musk Fragrances in a Conventional Drinking Water Treatment Plant with Lime Softening.

    Science.gov (United States)

    Wombacher, William D; Hornbuckle, Keri C

    2009-11-01

    Synthetic musk fragrances are common personal care product additives and wastewater contaminants that are routinely detected in the environment. This study examines the presence eight synthetic musk fragrances (AHTN, HHCB, ATII, ADBI, AHMI, musk xylene, and musk ketone) in source water and the removal of these compounds as they flow through a Midwestern conventional drinking water plant with lime softening. The compounds were measured in water, waste sludge, and air throughout the plant. HHCB and AHTN were detected in 100% of the samples and at the highest concentrations. A mass balance on HHCB and AHTN was performed under warm and cold weather conditions. The total removal efficiency for HHCB and AHTN, which averaged between 67% to 89%, is dominated by adsorption to water softener sludge and its consequent removal by sludge wasting and media filtration. Volatilization, chlorine disinfection, and the disposal of backwash water play a minor role in the removal of both compounds. As a result of inefficient overall removal, HHCB and AHTN are a constant presence at low levels in finished drinking water.

  13. Effect of water treatment additives on lime softening residual trace chemical composition--implications for disposal and reuse.

    Science.gov (United States)

    Cheng, Weizhi; Roessler, Justin; Blaisi, Nawaf I; Townsend, Timothy G

    2014-12-01

    Drinking water treatment residues (WTR) offer potential benefits when recycled through land application. The current guidance in Florida, US allows for unrestricted land application of lime softening WTR; alum and ferric WTR require additional evaluation of total and leachable concentrations of select trace metals prior to land application. In some cases a mixed WTR is produced when lime softening is accompanied by the addition of a coagulant or other treatment chemical; applicability of the current guidance is unclear. The objective of this research was to characterize the total and leachable chemical content of WTR from Florida facilities that utilize multiple treatment chemicals. Lime and mixed lime WTR samples were collected from 18 water treatment facilities in Florida. Total and leachable concentrations of the WTR were measured. To assess the potential for disposal of mixed WTR as clean fill below the water table, leaching tests were conducted at multiple liquid to solid ratios and under reducing conditions. The results were compared to risk-based soil and groundwater contamination thresholds. Total metal concentrations of WTR were found to be below Florida soil contaminant thresholds with Fe found in the highest abundance at a concentration of 3600 mg/kg-dry. Aluminum was the only element that exceeded the Florida groundwater contaminant thresholds using SPLP (95% UCL = 0.23 mg/L; risk threshold = 0.2 mg/L). Tests under reducing conditions showed elevated concentrations of Fe and Mn, ranging from 1 to 3 orders of magnitude higher than SPLP leachates. Mixed lime WTR concentrations (total and leachable) were lower than the ferric and alum WTR concentrations, supporting that mixed WTR are appropriately represented as lime WTR. Testing of WTR under reducing conditions demonstrated the potential for release of certain trace metals (Fe, Al, Mn) above applicable regulatory thresholds; additional evaluation is needed to assess management options where

  14. Lime

    Science.gov (United States)

    Miller, M.

    2006-01-01

    In 2005, US lime production was 20 Mt with a value of $1.5 billion. Production was unchanged compared with 2004. Captive production was 1.4 Mt. US consumption was 20.2 Mt. Most of the US lime trade was with Canada and Mexico. Despite some disruptions due to hurricanes Katrina and Rita, normal sales activities remained healthy.

  15. Process optimisation of lime milk leaching and control of cold lime softening at the power plant STEAG Fenne; Optimierung des Kalkansatzes und Regelung der Kalkmilchdosierung in der KZA des STEAG-Kraftwerks Fenne

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Christian [Steag Kraftwerk Fenne, Voelklingen (Germany). Anlagentechnik; Arenz, Helmut [Steag Kraftwerk Fenne, Voelklingen (Germany). Technischer Service; Wysk, Ralf [NALCO Deutschland GmbH, Frankfurt am Main (Germany). National Account Managing Kraftwerke

    2013-06-01

    An increase in turbidity in the cleaned water of the cold lime softener higher than the raw water input of the river Saar was observed at the Fenne site at some days in 2009. Also the post-installed sand filter could not restrain the fine particles. Under these circumstances the demineralisation water production had serious problems because of heavily fouled membranes in the reverse osmosis system. Only the immense personal actions of the operating staff could enable the reliability of the water preparation system on site. Together with Nalco the power plant service department implemented a plant audit on site. The purpose of the plant audit was to find the reason for the bottleneck in water preparation and to optimise and automate the water treatment system under the aspects of economical reliability and control efficiency. (orig.)

  16. Water Utility Lime Sludge Reuse – An Environmental Sorbent ...

    Science.gov (United States)

    Lime sludge can be used as an environmental sorbent to remove sulfur dioxide (SO2) and acid gases, by the ultra-fine CaCO3 particles, and to sequester mercury and other heavy metals, by the Natural Organic Matter and residual activated carbon. The laboratory experimental set up included a simulated flue gas preparation unit, a lab-scale wet scrubber, and a mercury analyzer system. The influent mercury concentration was based on a range from 22 surveyed power plants. The reactivity of the lime sludge sample for acid neutralization was determined using a method similar to method ASTM C1318-95. Similar experiments were conducted using reagent calcium carbonate and calcium sulfate to obtain baseline data for comparing with the lime sludge test results. The project also evaluated the techno-economic feasibility and sustainable benefits of reusing lime softening sludge. If implemented on a large scale, this transformative approach for recycling waste materials from water treatment utilities at power generation utilities for environmental cleanup can save both water and power utilities millions of dollars. Huge amounts of lime sludge waste, generated from hundreds of water treatment utilities across the U.S., is currently disposed in landfills. This project evaluated a sustainable and economically-attractive approach to the use of lime sludge waste as a valuable resource for power generation utilities.

  17. Lime treatment of liquid waste containing heavy metals, radionuclides and organics

    International Nuclear Information System (INIS)

    DuPont, A.

    1990-01-01

    This paper reports on lime treatment of liquid waste containing heavy metals, radio nuclides and organics. Lime is wellknown for its use in softening drinking water the treatment of municipal wastewaters. It is becoming important in the treatment of industrial wastewater and liquid inorganic hazardous waste; however, there are many questions regarding the use of lime for the treatment of liquid hazardous waste

  18. Cation Exchange Water Softeners

    Science.gov (United States)

    WaterSense released a notice of intent to develop a specification for cation exchange water softeners. The program has made the decision not to move forward with a spec at this time, but is making this information available.

  19. Uranium hydrogeochemical and stream sediment reconnaissance of the Lime Hills and Tyonek NTMS Quadrangles, Alaska, including concentrations of forty-three additional elements

    International Nuclear Information System (INIS)

    Jacobsen, S.I.; Aamodt, P.L.; Sharp, R.R. Jr.

    1979-01-01

    The U contents of the 671 waters from the Lime Hills quadrangle range from below 0.02 ppB to a high of 11.29 ppB. U contents of the 667 sediments from this quadrangle range from a low of 0.1 ppM to a high of 94.9 ppM. Both waters and sediments containing relatively high U concentrations are found to cluster in association with plutonic rocks in the Alaska Range, and particularly so in the vicinity of the Tired Pup batholith and Mount Estelle pluton. The U contents of 575 waters from the Tyonek quadrangle range from below the detection limit to 13.13 ppB. Relatively high U concentrations in waters were found to cluster near the Mount Estelle pluton and undifferentiated igneous, metasedimentary, and volcanic rocks in the Alaska Range and in Pleistocene deposits along the Castle Mountain fault. Uranium contents in 502 sediments from the Tyonek quadrangle range from 0.1 to 58 ppM. Most sediment samples having high U concentrations are from locations near the Mount Estelle pluton and Styx River batholith in the Alaska Range. Data for samples collected in the Alaska Range and the two flanking lowlands were also examined separately. Water samples from all source types in the Alaska Range had a higher mean U concentration (0.85 ppB) than those from the Western Lowland (0.34 ppB) or the Susitna Lowland (0.51 ppB). The mean U concentrations for lake water samples from the Alaska Range and the lowland areas are similar. Sediment samples from streams and lakes in the Alaska Range have a markedly higher mean U concentration (7.00 ppM) than sediment samples from either the Western Lowland (2.46 ppM) or the Susitna Lowland area

  20. Basic process of irradiation softening

    International Nuclear Information System (INIS)

    Makii, Koichi; Tsutsumi, Tetsuo; Aono, Yasuhisa; Kuramoto, Eiichi

    1987-01-01

    The authors have been engaged in research that uses the Johnson-Wilson potential (i.e., potential between two bodies) to analyze the interaction between the core of a spiral dislocation and point defects (interstitial atoms) under stress. Metals with the body-centered cubic structure, however, have covalent bonding nature and multi-body effects of d-electrons cannot be ignored. In the present work, the N-body potential, which takes into account such multi-body effects of d-electrons, is compared with the Johnson-Wilson potential. Compared to the Johnson-Wilson potential, the N-body potential suffers a considerably smaller misfit energy and allows computer simulation of the interaction to be performed at an external force level closer to that used in measurement. Low-stress, long-period relaxation causes pipe diffusion of crowdions. This causes the expansion of ''three-kink configuration'', leading to hardening. As a result of the pipe diffusion, crowdions are absorbed into spiral dislocations and released out of the crystal. It has been reported that during a tensile test at 77 K, irradiated samples are softened at the yield point and the degree of softening recovers as the strain increases. This also supports the idea that the number of defects decreases due to the interaction between dislocations and interstitial atoms. (Nogami, K.)

  1. Rootstocks for 'Tahiti' lime

    Directory of Open Access Journals (Sweden)

    Stenzel Neusa Maria Colauto

    2004-01-01

    Full Text Available The 'Tahiti' lime (Citrus latifolia Tanaka is an important commercial citrus cultivar in Brazil. 'Rangpur' lime has being used as its main rootstock, but it is susceptible to root rot caused by Phytophthora, reducing tree longevity. An experiment was set up in a randomized block design, with three trees per plot of each rootstock and four replicates, and run for 12 years, aiming to compare the performance of 'IAC-5 Tahiti' lime, budded on 'Rangpur' lime (Citrus limonia Osb.; 'C-13' citrange (Citrus sinensis (L. Osb. × Poncirus trifoliata (L. Raf.; 'African' rough lemon (Citrus jambhiri Lush.; 'Volkamer' lemon (Citrus volkameriana Ten. & Pasq.; trifoliate orange (Poncirus trifoliata (L. Raf.; 'Sunki' mandarin (Citrus sunki Hort. ex Tan. and 'Cleopatra' mandarin (Citrus reshni Hort. ex Tan.. Eleven years after the establishment of the orchard, trees with the greatest canopy development were budded on 'C-13' citrange and 'African' rough lemon, and both differed significantly from trees budded on trifoliate orange, 'Sunki' and 'Cleopatra' mandarins, which presented the smallest canopy development. Trees budded on 'Rangpur' lime and 'C-13' citrange had the highest cumulative yields, and were different from trees budded on trifoliate orange, 'Cleopatra' and 'Sunki' mandarins. There was no rootstock effect on mean fruit weight and on the total soluble solid/acid ratio in the juice. The 'Rangpur' lime and the 'Cleopatra' mandarin rootstocks reduced longevity of plants.

  2. Experimental investigation and constitutive model for lime mudstone.

    Science.gov (United States)

    Wang, Junbao; Liu, Xinrong; Zhao, Baoyun; Song, Zhanping; Lai, Jinxing

    2016-01-01

    In order to investigate the mechanical properties of lime mudstone, conventional triaxial compression tests under different confining pressures (0, 5, 15 and 20 MPa) are performed on lime mudstone samples. The test results show that, from the overall perspective of variation law, the axial peak stress, axial peak strain and elastic modulus of lime mudstone tend to gradually increase with increasing confining pressure. In the range of tested confining pressure, the variations in axial peak stress and elastic modulus with confining pressure can be described with linear functions; while the variation in axial peak strain with confining pressure can be reflected with a power function. To describe the axial stress-strain behavior in failure process of lime mudstone, a new constitutive model is proposed, with the model characteristics analyzed and the parameter determination method put forward. Compared with Wang' model, only one parameter n is added to the new model. The comparison of predicted curves from the model and test data indicates that the new model can preferably simulate the strain softening property of lime mudstone and the axial stress-strain response in rock failure process.

  3. Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Roland

    2005-12-15

    Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result in lime mud difficult to dewater, has not become true. Important experiences have come out which could be used as a base in further investigations.

  4. California Bearing Ratio (CBR) test on stabilization of clay with lime addition

    Science.gov (United States)

    Hastuty, I. P.; Roesyanto; Limbong, M. N.; Oberlyn, S. J.

    2018-02-01

    Clay is a type of soil with particles of certain minerals giving plastic properties when mixed with water. Soil has an important role in a construction, besides as a building material in a wide variety of civil engineering works, soil is also used as supporting foundation of the building. Basic properties of clay are rock-solid in dry and plastic with medium water content. In high water content, clay becomes sticky like (cohesive) and soften. Therefore, clay stabilization is necessary to repair soil’s mechanical properties. In this research, lime is use as a stabilizer that contains the Ca+ element to bond bigger particles. Lime used is slaked lime Ca(OH)2. Clay used has liquid limitation (LL) value of 47.33%, plasticity index of 29.88% and CBR value 6.29. The results explain about 10% lime mixture variation gives the optimum stabilized clay with CBR value of 8.75%.

  5. Potential Use Of Carbide Lime Waste As An Alternative Material To Conventional Hydrated Lime Of Cement-Lime Mortars

    OpenAIRE

    Al Khaja, Waheeb A.

    1992-01-01

    The present study aimed at the possibility of using the carbide lime waste as an alternative material to the conventional lime used for cement-lime mortar. The waste is a by-product obtained in the generation of acetylene from calcium carbide. Physical and chemical properties of the wastes were studied. Two cement-lime-sand mix proportions containing carbide lime waste were compared with the same mix proportions containing conventional lime along with a control mix without lime. Specimens wer...

  6. Hardening and softening mechanisms of pearlitic steel wire under torsion

    International Nuclear Information System (INIS)

    Zhao, Tian-Zhang; Zhang, Shi-Hong; Zhang, Guang-Liang; Song, Hong-Wu; Cheng, Ming

    2014-01-01

    Highlights: • Mechanical behavior of pearlitic steel wire is studied using torsion. • Work hardening results from refinement lamellar pearlitic structure. • Softening results from recovery, shear bands and lamellar fragmentations. • A microstructure based analytical flow stress model is established. - Abstract: The mechanical behaviors and microstructure evolution of pearlitic steel wires under monotonic shear deformation have been investigated by a torsion test and a number of electron microscopy techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), with an aim to reveal the softening and hardening mechanisms of a randomly oriented pearlitic structure during a monotonic stain path. Significantly different from the remarkable strain hardening in cold wire drawing, the strain hardening rate during torsion drops to zero quickly after a short hardening stage. The microstructure observations indicate that the inter-lamellar spacing (ILS) decreases and the dislocations accumulate with strain, which leads to hardening of the material. Meanwhile, when the strain is larger than 0.154, the enhancement of dynamic recovery, shear bands (SBs) and cementite fragmentations results in the softening and balances the strain hardening. A microstructure based analytical flow stress model with considering the influence of ILS on the mean free path of dislocations and the softening caused by SBs and cementite fragmentations, has been established and the predicted flow shear curve meets well with the measured curve in the torsion test

  7. Irradiation softening in pure iron single crystals

    International Nuclear Information System (INIS)

    Meshii, M.

    1975-01-01

    The characteristics of irradiation softening in Fe were studied. Results show that irradiation softening effect can be explained by the intrinsic mechanism, namely, the interaction of screw dislocations with randomly dispersed interstitials. At least some of the solid solution softening phenomena observed in alloys can be explained by the same mechanism. However, the alloying may be accompanied by an additional effect such as solute segregation to dislocations which may also strongly affect the yield stress. This effect may mask the softening effect partially or totally. Changes in the dislocation structure of deformed specimens caused by alloying, which are often reported in electron microscopic investigations, support this contention. The alloying, therefore, may not be as good as the low temperature irradiation in studying the effect of random solutes on dislocation motion and yield stress

  8. Softening behaviour of concrete : numerical research

    NARCIS (Netherlands)

    Bongers, J.P.W.; Rutten, H.S.; Fijneman, H.J.

    1994-01-01

    Experimental research shows, apart from the influence of multiaxial loading conditions, that softening of concrete loaded in compression is accompanied by localization of deformations. Therefore, numerical modelling of concrete material behaviour has to take this effect into account. This implies

  9. [Review of lime carbon sink.

    Science.gov (United States)

    Liu, Li Li; Ling, Jiang Hua; Tie, Li; Wang, Jiao Yue; Bing, Long Fei; Xi, Feng Ming

    2018-01-01

    Under the background of "missing carbon sink" mystery and carbon capture and storage (CCS) technology development, this paper summarized the lime material flow process carbon sink from the lime carbonation principles, impact factors, and lime utilization categories in chemical industry, metallurgy industry, construction industry, and lime kiln ash treatment. The results showed that the lime carbonation rate coefficients were mainly impacted by materials and ambient conditions; the lime carbon sink was mainly in chemical, metallurgy, and construction industries; and current researches focused on the mechanisms and impact factors for carbonation, but their carbon sequestration calculation methods had not been proposed. Therefore, future research should focus on following aspects: to establish a complete system of lime carbon sequestration accounting method in view of material flow; to calculate lime carbon sequestration in both China and the world and explain their offset proportion of CO 2 emission from lime industrial process; to analyze the contribution of lime carbon sequestration to missing carbon sink for clarifying part of missing carbon sinks; to promote the development of carbon capture and storage technology and provide some scientific bases for China's international negotiations on climate change.

  10. Dolomitic lime containing hydraulic additive

    International Nuclear Information System (INIS)

    Lagzdina, S.; Sedmalis, U.; Bidermanis, L.; Liepins, J.; Grosvalds, I.

    1997-01-01

    To obtain qualitative dolomitic lime the optimum calcination temperature of dolomite containing about 9 % of clayey substances is 900 deg C. The mechanical strength of dolomitic lime containing 30 % of brick waste additive after 6-9 months of hardening is 1.4-1.5 times higher than that of samples without hydraulic additive, for calcium lime - 2.2-2.6 times higher. Generally the mechanical strength of dolomitic lime is higher than that one of calcium lime. It can be explained by the active role of MgO in the hydration and hardening processes of dolomitic lime. Xray diffraction phase analysis was performed by X-ray diffractometer DPON-3M with Cu-K α emission filter

  11. Lime-water consolidation effects on poor lime mortars

    Czech Academy of Sciences Publication Activity Database

    Drdácký, Miloš; Slížková, Zuzana

    2012-01-01

    Roč. 43, č. 1 (2012), s. 31-36 ISSN 0044-9466 R&D Projects: GA ČR(CZ) GA103/09/2067 Institutional support: RVO:68378297 Keywords : lime mortar s * lime -water consolidation * conservation Subject RIV: JN - Civil Engineering

  12. LIME REQUIREMENT DETERMINATION AND LIMING IMPACT ON SOIL NUTRIENT STATUS

    Directory of Open Access Journals (Sweden)

    Krunoslav Karalić

    2010-06-01

    Full Text Available The aim of conducted research was to determine the influence of liming, mineral and organic fertilization on soil chemical properties and nutrient availability in the soil, yield height and mineral composition of alfalfa. Results were used to create regression models for prediction of liming impact on soil chemical properties. Liming and fertilization experiment was sat up in 20 L volume plastic pots with two types of acid soils with different texture from two sites. Ten liming and fertilization treatments were applied in four repetitions. Lime treatments increased soil pH values and decreased hydrolytic acidity. Mineral and organic fertilization affected additional soil acidification. Application of lime intensified mineralization and humus decomposition, while organic fertilization raised humus content. The results showed significant increase of AL-P2O5 and K2O availability. The treatments increased soil Ca concentrations, but at the same time decreased exchangeable Mg concentrations. Soil pH increase resulted in lower Fe, Mn, Zn and Cu availability. Soil CEC was increased by applied treatments. Lime rates increased number and height of alfalfa plants, as well as yield of leaf, stalk increased concentrations of N, P, K and Ca in alfalfa leaf and stalk, but decreased leaf Mg and Fe, Mn, Zn and Cu concentrations. Regression computer models predicted with adequate accuracy P, Fe, Mn, Zn and Cu availability and final pH value as a result of liming and fertilization impact.

  13. Stress-Softening Formulae of Polymer Bearings

    Directory of Open Access Journals (Sweden)

    M. H. B. M. Shariff

    2015-01-01

    Full Text Available The motivation for this work was the absence of closed form solutions that can reasonably describe the axial deformation behaviour of stress-softening polymer bearings. In this paper, new closed form solutions that exhibit Mullins phenomenon are developed. We show that the apparent Young modulus depends on the shape factor and the minimal infinitesimal strain. We furthermore found that, in a nonlinear deformation, the shape factor plays an important role in stress softening. The solutions are design friendly and are consistent with expected results.

  14. Solving the Standard Model Problems in Softened Gravity

    CERN Document Server

    Salvio, Alberto

    2016-11-16

    The Higgs naturalness problem is solved if the growth of Einstein's gravitational interaction is softened at an energy $ \\lesssim 10^{11}\\,$GeV (softened gravity). We work here within an explicit realization where the Einstein-Hilbert Lagrangian is extended to include terms quadratic in the curvature and a non-minimal coupling with the Higgs. We show that this solution is preserved by adding three right-handed neutrinos with masses below the electroweak scale, accounting for neutrino oscillations, dark matter and the baryon asymmetry. The smallness of the right-handed neutrino masses (compared to the Planck scale) and the QCD $\\theta$-term are also shown to be natural. We prove that a possible gravitational source of CP violation cannot spoil the model, thanks to the presence of right-handed neutrinos. Starobinsky inflation can occur in this context, even if we live in a metastable vacuum.

  15. Lime stabilization of expansive soil from Sergipe - Brazil

    Directory of Open Access Journals (Sweden)

    Leite Rafaella

    2016-01-01

    Full Text Available Expansive soils are characterized by volumetric changes caused by variations in moisture. They can cause several damages to civil constructions, especially to lightweight structures, including cracks and fissures. Chemical stabilization through addition of lime is one of the most effective techniques used to treat this type of soil. Due to cationic exchanges, lime can significantly reduce swell potential. This research studied a disturbed sample of expansive soil collected in Nossa Senhora do Socorro – Sergipe, Brazil, through the following laboratory tests: sieve and hydrometer tests, Atterberg Limits, compaction, free swell and swell pressure. All direct and indirect methods mentioned in this paper indicated that the natural soil presented high to very high degree of expansion, which reached approximately 20% of free swell and nearly 200 kPa of swell pressure. In order to evaluate the effect of lime, the same tests were conducted in soil-lime mixtures, using lime contents of 3%, 6% and 9%. The results confirmed the efficiency of lime stabilization. It was noted that, as lime content increased, there was reduction of clay fraction and increment of silt fraction; plasticity index decreased to nearly its half; compaction curve was displaced; and free swell and swell pressure reduced significantly.

  16. Not changing minds but softening hearts.

    Science.gov (United States)

    Morey, Jerad

    2013-01-01

    When a political decision threatened to divide communities, the Minnesota Council of Churches found a way not to change minds but to soften hearts. The Respectful Conversations Project built empathy and improved relationships, and is still helping to bring peace to communities and strengthening civic engagement in the state.

  17. Softening and elution of monomers in ethanol

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Asmussen, Erik; Munksgaard, E Christian

    2009-01-01

    The purpose of this study was to investigate the effect of light-curing protocol on softening and elution of monomers in ethanol as measured on a model polymer. It was a further aim to correlate the measured values with previously reported data on degree of conversion and glass transition...

  18. Softening behaviour of concrete : experimental research

    NARCIS (Netherlands)

    Geel, van H.J.G.M.; Rutten, H.S.; Fijneman, H.J.

    1994-01-01

    Uniaxial compressive softening tests on two types of concrete have been carried out, varying the type of loading platen and specimen size. In total 37 specimens were tested, 18 with polished steel loading platens and 19 with teflon loading platens. Half of the specimens were made of normal strength

  19. By-product reuse in drinking water softening: influence of operating conditions on calcium carbonate pellet characteristics

    DEFF Research Database (Denmark)

    Tang, Camilla; Rosshaug, P. S.; Kristensen, J. B.

    both socio-economic and environmental benefits. However, optimal implementation of softening requires a holistic approach including e.g. possibilities for by-product reuse. A pellet reactor is one widely used softening technology that may produce up to 350 kg calcium carbonate pellets per 1000 m3...

  20. Curvature Effect and the Spectral Softening Phenomenon Detected ...

    Indian Academy of Sciences (India)

    soft spectral evolution, indicating that this spectral softening is not a rare phenomenon .... of time, there exists a temporal steep decay phase accompanied by spectral softening. (d) In most cases, the temporal power law index α and the spectral.

  1. Durability of air lime mortar

    DEFF Research Database (Denmark)

    Nielsen, Anders

    2016-01-01

    This contribution deals with the physical and chemical reasons why pure air lime mortars used in masonry of burned bricks exposed to outdoor climate have shown to be durable from the Middle Ages to our days. This sounds strange in modern times where pure air lime mortars are regarded as weak...... materials, which are omitted from standards for new masonry buildings, where use of hydraulic binders is prescribed. The reasons for the durability seam to be two: 1. The old mortars have high lime contents. 2. The carbonation process creates a pore structure with a fine pored outer layer and coarser pores...

  2. Acidic deposition: State of science and technology. Report 15. Liming acidic surface waters. Final report

    International Nuclear Information System (INIS)

    Olem, H.; Thornelof, E.; Sandoy, S.; Schreiber, R.K.

    1990-09-01

    The document describes the science and technology of aquatic liming--a method for improving the water quality of acidic surface waters to restore or enhance fisheries. The report is a comprehensive compilation of years of research in North America and Europe by dozens of scientists. Several mitigation technologies--including those that have only been proposed--are critically evaluated along with the effects of liming on water chemistry and aquatic biota. Through these evaluations, the state of the science and technology of aquatic liming is identified for the reader. Whole-lake liming is now recognized as a valuable management tool for acidic surface waters and their fisheries. However, some liming technologies are considered experimental and will need further evaluation. Distinctions between technologies are included--as is the distinction between liming acidic surface waters and reducing acidifying emissions

  3. Geomechanical properties of lime stabilized clayey sands

    International Nuclear Information System (INIS)

    Arabani, M.; Karami, M. Veis

    2007-01-01

    Clayey sands that have low plasticity, low compressibility and high strength under loads, are suitable as a base material for any engineering construction projects as well as for roads and building construction. Decrease of plasticity and compressibility as well as increase in strength of these materials can be obtained by many different methods. Of these methods, lime stabilization is a common, applicable, and easy to use approach that can improve geomechanical and geotechnical properties of clayey sand fills. In this study some important geomechanical properties and geotechnical properties of clayey sands including compressive strength, CBR and elastic plastic behavior are investigated. A range of gradations representative of those gradations found in situ in the north of Iran were selected for testing and samples were artificially rebuilt in the laboratory. The mixes were then stabilized with hydrated lime and cured. Different mechanical tests were performed on mature materials. The stress-strain behavior of lime-stabilized mixes was plotted and a parabolic function was used to estimate the trend of stress-strain behavior. The data show that there is a correlation among the results of uniaxial load test, tensile strength, and CBR of the tested specimens. Also, results of the unconfined compression test and the indirect tensile strength test show that an increase in clay content up to a certain percent, in the clay-sand fills, tends to increase the strength of the materials in compression as well as in tension. (author)

  4. Liming impacts on soils, crops and biodiversity in the UK: A review.

    Science.gov (United States)

    Holland, J E; Bennett, A E; Newton, A C; White, P J; McKenzie, B M; George, T S; Pakeman, R J; Bailey, J S; Fornara, D A; Hayes, R C

    2018-01-01

    Fertile soil is fundamental to our ability to achieve food security, but problems with soil degradation (such as acidification) are exacerbated by poor management. Consequently, there is a need to better understand management approaches that deliver multiple ecosystem services from agricultural land. There is global interest in sustainable soil management including the re-evaluation of existing management practices. Liming is a long established practice to ameliorate acidic soils and many liming-induced changes are well understood. For instance, short-term liming impacts are detected on soil biota and in soil biological processes (such as in N cycling where liming can increase N availability for plant uptake). The impacts of liming on soil carbon storage are variable and strongly relate to soil type, land use, climate and multiple management factors. Liming influences all elements in soils and as such there are numerous simultaneous changes to soil processes which in turn affect the plant nutrient uptake; two examples of positive impact for crops are increased P availability and decreased uptake of toxic heavy metals. Soil physical conditions are at least maintained or improved by liming, but the time taken to detect change varies significantly. Arable crops differ in their sensitivity to soil pH and for most crops there is a positive yield response. Liming also introduces implications for the development of different crop diseases and liming management is adjusted according to crop type within a given rotation. Repeated lime applications tend to improve grassland biomass production, although grassland response is variable and indirect as it relates to changes in nutrient availability. Other indicators of liming response in grassland are detected in mineral content and herbage quality which have implications for livestock-based production systems. Ecological studies have shown positive impacts of liming on biodiversity; such as increased earthworm abundance that

  5. Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Roland

    2003-07-15

    Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Project owner has been the Swedish company Torkapparater AB, and the project is performed inside the 'Vaermeforsk Program for Pulp and Paper Industry 2004-2005'. Other partners, besides SMA Svenska Mineral AB, has been Stora Enso Skoghalls Bruk, Carnot AB, AaF Process AB and KTH Energiprocesser. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result

  6. Lime Stabilization of Fine-Grained Greenlandic Sediments in Relation to Construction Projects

    DEFF Research Database (Denmark)

    Jørgensen, Anders Stuhr; Ingeman-Nielsen, Thomas; Nielsen, Hans Rasmus

    2010-01-01

    to the cold climate, and it is therefore of great interest to study possible methods to improve the stability of the fine-grained sediments. This presentation will include results of laboratory studies of lime stabilization on a clay soil from Kangerlussuaq, western Greenland. The result includes tests...... of the optimum lime mixture in relation to both reaction time and temperature influence....

  7. Freeze concentration of lime juice

    Directory of Open Access Journals (Sweden)

    Ampawan Tansakul

    2008-11-01

    Full Text Available The main objective of this research was to study the effects of processing conditions, i.e. cooling medium temperature (-6, -12 and -18C and scraper blade rotational speed (50, 100 and 150 rpm on the freeze concentration of lime juice. The initial soluble solid content of lime juice was 7.6 Brix. Results showed that soluble solid content of lime juice increased as cooling medium temperature decreased while scraper blade rotational speed increased. It was also found that the processing condition with -18˚C cooling medium temperature and 150 rpm rotational speed of the scraper blade was the best among all studied conditions, although the loss of the soluble solids with ice crystals during ice separation was relatively high at 35%.

  8. Effect of softening precipitate composition and surface characteristics on natural organic matter adsorption.

    Science.gov (United States)

    Russell, Caroline G; Lawler, Desmond F; Speitel, Gerald E; Katz, Lynn E

    2009-10-15

    Natural organic matter (NOM) removal during water softening is thought to occur through adsorption onto or coprecipitation with calcium and magnesium solids. However, details of precipitate composition and surface chemistry and subsequent interactions with NOM are relatively unknown. In this study, zeta potentiometry analyses of precipitates formed from inorganic solutions under varying conditions (e.g., Ca-only, Mg-only, Ca + Mg, increasing lime or NaOH dose) indicated that both CaCO3 and Mg(OH)2 were positively charged at higher lime (Ca(OH)2) and NaOH doses (associated with pH values above 11.5), potentially yielding a greater affinity for adsorbing negatively charged organic molecules. Environmental scanning electron microscopy (ESEM) images of CaCO3 solids illustrated the rhombohedral shape characteristic of calcite. In the presence of increasing concentrations of magnesium, the CaCO3 rhombs shifted to more elongated crystals. The CaCO3 solids also exhibited increasingly positive surface charge from Mg incorporation into the crystal lattice, potentially creating more favorable conditions for adsorption of organic matter. NOM adsorption experiments using humic substances extracted from Lake Austin and Missouri River water elucidated the role of surface charge and surface area on adsorption.

  9. Optimization of lime treatment processes

    International Nuclear Information System (INIS)

    Zinck, J. M.; Aube, B. C.

    2000-01-01

    Lime neutralization technology used in the treatment of acid mine drainage and other acidic effluents is discussed. Theoretical studies and laboratory experiments designed to optimize the technology of lime neutralization processes and to improve the cost efficiency of the treatment process are described. Effluent quality, slaking temperature, aeration, solid-liquid separation, sludge production and geochemical stability have been studied experimentally and on site. Results show that through minor modification of the treatment process, costs, sludge volume generated, and metal released to the environment can be significantly reduced. 17 refs., 4 figs

  10. Mineral Resource of the Month: Lime

    Science.gov (United States)

    Corathers, Lisa A.

    2015-01-01

    Lime is the common term for several chemicals in three major categories: quicklime, hydrated lime and refractory dead-burned dolomite. Lime is almost never found naturally. It is primarily manufactured by burning limestone in kilns, followed by hydration when necessary. 

  11. Lime treatment of stabilized leachates

    International Nuclear Information System (INIS)

    Renou, S.; Poulain, S.; Givaudan, J. G.; Sahut, C.; Moulin, P.

    2009-01-01

    Reverse Osmosis is the most widely used method for treating municipal solid waste landfill leachates, since it produces a permeate in compliance with reject requirements. However, the efficiency of this process at the industrial scale is limited mainly because of membrane fouling and the high osmotic pressures involved. Although lime precipitation is traditionally used to eliminate the temporary hardness of water by de-carbonation, it has also been shown to be highly efficient in removing humic substances which are known to have strong fouling potential towards membranes. Our objective is to study the lime/leachate physico-chemistry, in order to determine the potential of the lime precipitation as pre-treatment for reverse osmosis. The results show that the lime treatment makes it possible (i) to act efficiently on the inorganic fraction of leachates through a de-carbonation mechanism which entails massive precipitation of the carbonates under the form of CaCO 3 , (ii) to eliminate by co-precipitation the high Molecular Weight (MW) organic macromolecules (≥ 50, 000 g.mol -1 ) such as humic acids, and (iii) to generate a stable residue that can be easily stored at a landfill. The reverse osmosis step will be facilitated through significant reduction of the osmotic pressures and prevention of membrane fouling. (authors)

  12. Softening during deformation of Zr alloys

    International Nuclear Information System (INIS)

    Kral, R.; Trojanova, Z.; Lukac, P.

    1994-01-01

    The strain hardening behaviour is described by the work hardening rate. The work hardening rate depends on the dislocation density changes which result from the competition between the rate of dislocation storage and the rate of annihilation of dislocations. In the present work the deformation behaviour of Zr-based alloys is investigated. From the stress-strain curves the work hardening rate is calculated and its stress dependence is studied at various temperatures between 300 and 1000 K. Experimental investigations show that at first the work hardening rate decreases quasi-linearly with increasing stress. After a certain stress is reached, the work hardening rate decreases more slowly with increasing stress. We discuss the influence of hardening and softening processes on the deformation behaviour. Analytical models are compared with experimental results. (orig.)

  13. Softening in Random Networks of Non-Identical Beams.

    Science.gov (United States)

    Ban, Ehsan; Barocas, Victor H; Shephard, Mark S; Picu, Catalin R

    2016-02-01

    Random fiber networks are assemblies of elastic elements connected in random configurations. They are used as models for a broad range of fibrous materials including biopolymer gels and synthetic nonwovens. Although the mechanics of networks made from the same type of fibers has been studied extensively, the behavior of composite systems of fibers with different properties has received less attention. In this work we numerically and theoretically study random networks of beams and springs of different mechanical properties. We observe that the overall network stiffness decreases on average as the variability of fiber stiffness increases, at constant mean fiber stiffness. Numerical results and analytical arguments show that for small variabilities in fiber stiffness the amount of network softening scales linearly with the variance of the fiber stiffness distribution. This result holds for any beam structure and is expected to apply to a broad range of materials including cellular solids.

  14. Surface morphology study in high speed milling of soda lime glass

    Science.gov (United States)

    Konneh, Mohamed; Bagum, Mst. Nasima; Ali, Mohammad Yeakub; Amin, A. K. M. Nurul

    2018-05-01

    Soda lime glass has a wide range of applications in optical, bio-medical and semi-conductor industries. It is undeniably a challenging task to produce micro finish surface on an amorphous brittle solid like soda lime glass due to its low fracture toughness. In order to obtain such a finish surface, ductile machining has been exploited, as this usually cause's plastic flow which control crack propagation. At sub-micro scale cutting parameters, researchers achieved nano finish surface in micro milling operation using coated tool. However it is possible to enhance the rate of material removal (RMR) of soda lime glass at flexible cutting condition. High speed cutting at micro meter level, extend of thermal softening might be prominent than the strain gradient strengthening. The purpose of this study was to explore the effects of high cutting speed end milling parameters on the surface texture of soda lime glass using uncoated carbide tool. The spindle speed, depth of cut and feed rate were varied from 20,000 to 40,000 rpm, 10 to 30 mm/min and 30 to 50 µm respectively. Mathematical model of roughness has been developed using Response Surface Methodology (RSM). Experimental verification confirmed that surface roughness (Ra) 0.38 µm is possible to achieve at increased RMR, 4.71 mm3/min.

  15. CHEMICAL SOIL ATTRIBUTES AS AFFECTED BY LIME AND GYPSUM SURFACE APPLICATION

    Directory of Open Access Journals (Sweden)

    A. Mantovani

    2017-10-01

    Full Text Available The gypsum is a soil condition end it has to function contribute to the elimination or reduction of aluminum in the soil in depth. Still, it can contribute to the distribution of nutrients in the soil profile more uniformly and thus increasing the productivity of crops. This study aimed to evaluate the influence of gypsum application, with and without lime, on soil chemical properties and soybean yield, in a no-till system. The experiment was carried in Campos Novos, Santa Catarina State, Brazil, with a randomized block design and split plot design with four replications, the main portion was distributed gypsum doses (1000, 2000, 4000 and 6000 kg ha-1 without incorporation, and the split plot (with and without lime and the liming was 2,000 kg ha-1. We evaluated the performance of components and productivity of soybeans. It was also analyzed the soil pH and Ca, Mg, S and Al at 0-20 and 20-40 cm. The application of gypsum at the rates tested surface with and without lime did not affect the yield components and soybean productivity. At 0-20 cm soil depth lime application increased soil pH by 0.3 units on the average rates of gypsum, but in the 20-40 cm layer was not found effect of lime and gypsum in pH ground due to the short time between application and evaluation. In areas with and without lime contents of Ca and S in the two layers evaluated increased with increasing rates of gypsum, since Mg has difference with the lime application on a 0-20 cm to dose 4000 kg ha-1 and the lime in the gypsum rates and Al decreased with increasing dose gypsum average in the 20-40 cm layer depth. The application of gypsum and limestone softened the negative effects of soil acidity and the increase mainly of calcium and sulfur at 0-20 cm, with less efficient effects in the 20-40 cm layer due to the soil is clayey and the period between the implementation and evaluation be 120 days.

  16. Searching for Terrain Softening near Mercury's North Pole

    Science.gov (United States)

    Cobian, P. S.; Vilas, F.; Lederer, S. M.; Barlow, N. G.

    2004-01-01

    In 1999, following the initial discovery of radar bright craters near both poles of Mercury measured the depth-todiameter (d/D) ratios of 170 impact craters in Mariner 10 images covering four different regions on Mercury s surface. Rapid softening of crater structure, indicated by lower d/D ratios, could indicate the possibility of subsurface water ice in Mercury's terrain originating from an internal source in the planet. Their study included 3 specific radar bright craters suggested to contain ice. They concluded that no terrain softening was apparent, and a rapidly emplaced exogenic water source was the most likely source for the proposed ice in these craters. Recent radar observations of the Mercurian North pole have pinpointed many additional radar bright areas with a resolution 10x better than previous radar measurements, and which correlate with craters imaged by Mariner 10. These craters are correlated with regions that are permanently shaded from direct sunlight, and are consistent with observations of clean water ice. We have expanded the initial study by Barlow et al. to include d/D measurements of 12 craters newly identified as radar bright at latitudes poleward of +80o. The radar reflectivity resemblances to Mars south polar cap and echoes from three icy Galilean satellites suggest that these craters too may have polar ice on Mercury. The effect of subsurface H20 on impact craters is a decrease in its d/D ratio, and softening of crater rims over a period of time. The study of Barlow et al., focused on determining the d/D ratios of 170 impact craters in the Borealis (north polar), Tolstoj (equatorial), Kuiper (equatorial), and Bach (south polar) quadrangles. This work focuses on the newly discovered radar bright craters, investigating their d/D ratios as an expansion of the earlier work..We compare our results to the statistical results from Barlow et al. here. With the upcoming Messenger spacecraft mission to Mercury, this is an especially timely study

  17. Solidification of radioactive waste in a cement/lime mixture

    International Nuclear Information System (INIS)

    Zhou, H.; Colombo, P.

    1984-01-01

    The suitability of a cement/lime mixture for use as a solidification agent for different types of wastes was investigated. This work includes studies directed towards determining the wasted/binder compositional field over which successful solidification occurs with various wastes and the measurement of some of the waste from properties relevant to evaluating the potential for the release of radionuclides to the environment. In this study, four types of low-level radioactive wastes were simulated for incorporation into a cement/lime mixture. These were boric acid waste, sodium sulfate wastes, aion exchange resins and incinerator ash. 7 references, 3 figures, 2 tables

  18. A truly Newtonian softening length for disc simulations

    Science.gov (United States)

    Huré, J.-M.; Trova, A.

    2015-02-01

    The softened point mass model is commonly used in simulations of gaseous discs including self-gravity while the value of associated length λ remains, to some degree, controversial. This `parameter' is however fully constrained when, in a discretized disc, all fluid cells are demanded to obey Newton's law. We examine the topology of solutions in this context, focusing on cylindrical cells more or less vertically elongated. We find that not only the nominal length depends critically on the cell's shape (curvature, radial extension, height), but it is either a real or an imaginary number. Setting λ as a fraction of the local disc thickness - as usually done - is indeed not the optimal choice. We then propose a novel prescription valid irrespective of the disc properties and grid spacings. The benefit, which amounts to 2-3 more digits typically, is illustrated in a few concrete cases. A detailed mathematical analysis is in progress.

  19. Effects of liming on forage availability and nutrient content in a forest impacted by acid rain.

    Directory of Open Access Journals (Sweden)

    Sarah E Pabian

    Full Text Available Acidic deposition and subsequent forest soil acidification and nutrient depletion can affect negatively the growth, health and nutrient content of vegetation, potentially limiting the availability and nutrient content of forage for white-tailed deer (Odocoileus virginianus and other forest herbivores. Liming is a mitigation technique that can be used to restore forest health in acidified areas, but little is known about how it affects the growth or nutrient content of deer forage. We examined the effects of dolomitic limestone application on the growth and chemical composition of understory plants in an acidified forest in central Pennsylvania, with a focus on vegetative groups included as white-tailed deer forage. We used a Before-After-Control-Impact study design with observations 1 year before liming and up to 5 years post-liming on 2 treated and 2 untreated 100-ha sites. Before liming, forage availability and several nutrients were below levels considered optimal for white-tailed deer, and many vegetative characteristics were related to soil chemistry. We observed a positive effect of liming on forb biomass, with a 2.7 fold increase on limed sites, but no biomass response in other vegetation groups. We observed positive effects of liming on calcium and magnesium content and negative effects on aluminum and manganese content of several plant groups. Responses to liming by forbs and plant nutrients show promise for improving vegetation health and forage quality and quantity for deer.

  20. Improvement and Application of the Softened Strut-and-Tie Model

    Science.gov (United States)

    Fan, Guoxi; Wang, Debin; Diao, Yuhong; Shang, Huaishuai; Tang, Xiaocheng; Sun, Hai

    2017-11-01

    Previous experimental researches indicate that reinforced concrete beam-column joints play an important role in the mechanical properties of moment resisting frame structures, so as to require proper design. The aims of this paper are to predict the joint carrying capacity and cracks development theoretically. Thus, a rational model needs to be developed. Based on the former considerations, the softened strut-and-tie model is selected to be introduced and analyzed. Four adjustments including modifications of the depth of the diagonal strut, the inclination angle of diagonal compression strut, the smeared stress of mild steel bars embedded in concrete, as well as the softening coefficient are made. After that, the carrying capacity of beam-column joint and cracks development are predicted using the improved softened strut-and-tie model. Based on the test results, it is not difficult to find that the improved softened strut-and-tie model can be used to predict the joint carrying capacity and cracks development with sufficient accuracy.

  1. Water Softeners: How Much Sodium Do They Add?

    Science.gov (United States)

    ... diet is by putting away the saltshaker and cutting back on processed foods. With Sheldon G. Sheps, ... Original article: http://www.mayoclinic.org/healthy-lifestyle/nutrition-and-healthy-eating/expert-answers/water-softeners-sodium/ ...

  2. Effect of softening function on the cohesive crack fracture ...

    Indian Academy of Sciences (India)

    The cohesive crack model with linear softening yields the fracture process zones lower by ..... ignored during numerical simulation. In the crack band ..... performed with developed computer program using MATLAB for the following numerical.

  3. Comparative evaluation of aerial lime mortars for architectural conservation

    OpenAIRE

    Faria, Paulina; Henriques, Fernando M.A.; Rato, Vasco

    2008-01-01

    Journal of Cultural Heritage 9 (2008) 338-346 International bibliography on conservation usually refers that mortars made with lime putty with long extinction periods behave better than others made with the current dry hydrated limes. In order to evaluate this assess, an experimental study of lime mortars was carried out, using dry hydrated lime and two lime putties. It becomes clear that the use of lime putties with long extinction periods in mortars allow better performances, pa...

  4. Ectomycorrhizal activity as affected by soil liming

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Solbritt

    1996-05-01

    Acidification of the forest soils in southern Sweden due to atmospheric deposition has become evident during recent decades. To counteract further acidification, liming of forests in the most affected areas has been proposed. Most forest trees in the temperate and boreal forest ecosystems live in symbiosis with ectomycorrhizal fungi, and their uptake of mineral nutrients from the soil is greatly influenced by the symbiosis. In this thesis effects of liming on ectomycorrhiza have been studied in relation to effects on root colonization, fungal growth and nitrogen uptake. In field experiments the effects of liming on ectomycorrhizal colonization of root tips were variable, possibly due to different soil types and climatic variations. However, a changed mycorrhizal community structure could be detected. Laboratory studies also showed that the substrate may influence the outcome of lime applications; the nutrient status of the substrate had a marked effect on how mycelial growth was affected by liming. Under the experimental conditions used in the studies presented in this thesis, liming reduced the uptake of nitrogen and phosphorus by both mycorrhizal and non-mycorrhizal plants. The amount of extractable nitrogen and phosphorus in the peat was also reduced by liming. The latter could be due to either microbial or chemical immobilization. The lime induced decrease in nitrogen uptake was stronger in non-mycorrhizal plants than in mycorrhizal plants. Thus, the mycorrhizal plants had a higher ability to deal with the negative effects of liming on nitrogen availability. This was not the case for phosphorus. The lime induced decrease in phosphorus uptake was stronger for mycorrhizal plants, and in the highest lime treatment there was no significant difference between the mycorrhizal and the non-mycorrhizal spruce plants. 76 refs, 2 figs, 1 tab

  5. Phylogenetic origin of limes and lemons revealed by cytoplasmic and nuclear markers.

    Science.gov (United States)

    Curk, Franck; Ollitrault, Frédérique; Garcia-Lor, Andres; Luro, François; Navarro, Luis; Ollitrault, Patrick

    2016-04-01

    The origin of limes and lemons has been a source of conflicting taxonomic opinions. Biochemical studies, numerical taxonomy and recent molecular studies suggested that cultivated Citrus species result from interspecific hybridization between four basic taxa (C. reticulata,C. maxima,C. medica and C. micrantha). However, the origin of most lemons and limes remains controversial or unknown. The aim of this study was to perform extended analyses of the diversity, genetic structure and origin of limes and lemons. The study was based on 133 Citrus accessions. It combined maternal phylogeny studies based on mitochondrial and chloroplastic markers, and nuclear structure analysis based on the evaluation of ploidy level and the use of 123 markers, including 73 basic taxa diagnostic single nucleotide polymorphism (SNP) and indel markers. The lime and lemon horticultural group appears to be highly polymorphic, with diploid, triploid and tetraploid varieties, and to result from many independent reticulation events which defined the sub-groups. Maternal phylogeny involves four cytoplasmic types out of the six encountered in the Citrus genus. All lime and lemon accessions were highly heterozygous, with interspecific admixture of two, three and even the four ancestral taxa genomes. Molecular polymorphism between varieties of the same sub-group was very low. Citrus medica contributed to all limes and lemons and was the direct male parent for the main sub-groups in combination with C. micrantha or close papeda species (for C. aurata, C. excelsa, C. macrophylla and C. aurantifolia--'Mexican' lime types of Tanaka's taxa), C. reticulata(for C. limonia, C. karna and C. jambhiri varieties of Tanaka's taxa, including popular citrus rootstocks such as 'Rangpur' lime, 'Volkamer' and 'Rough' lemons), C. aurantium (for C. limetta and C. limon--yellow lemon types--varieties of Tanaka's taxa) or the C. maxima × C. reticulate hybrid (for C. limettioides--'Palestine sweet' lime types--and C

  6. Viscosity and Softening Behavior of Alkali Zinc Sulfophosphate Glasses

    DEFF Research Database (Denmark)

    Da, Ning; Krolikowski, Sebastian; Nielsen, Karsten Hansgaard

    2010-01-01

    We report on the softening properties and viscosity of glasses from the system ZnO-Na2O-SO3-P2O5 for low-temperature sealing applications. Up to a ratio of network-forming ions PO(4)3-:SO(4)2- of about 2:1, a gradual substitution of P2O5 by SO3 results in decreasing glass transition and softening...

  7. Genetic improvement of tomato by targeted control of fruit softening

    KAUST Repository

    Uluisik, Selman

    2016-07-25

    Controlling the rate of softening to extend shelf life was a key target for researchers engineering genetically modified (GM) tomatoes in the 1990s, but only modest improvements were achieved. Hybrids grown nowadays contain \\'non-ripening mutations\\' that slow ripening and improve shelf life, but adversely affect flavor and color. We report substantial, targeted control of tomato softening, without affecting other aspects of ripening, by silencing a gene encoding a pectate lyase. © 2016 Nature America, Inc. All rights reserved.

  8. Genetic improvement of tomato by targeted control of fruit softening

    KAUST Repository

    Uluisik, Selman; Chapman, Natalie H; Smith, Rebecca; Poole, Mervin; Adams, Gary; Gillis, Richard B; Besong, Tabot M.D.; Sheldon, Judith; Stiegelmeyer, Suzy; Perez, Laura; Samsulrizal, Nurul; Wang, Duoduo; Fisk, Ian D; Yang, Ni; Baxter, Charles; Rickett, Daniel; Fray, Rupert; Blanco-Ulate, Barbara; Powell, Ann L T; Harding, Stephen E; Craigon, Jim; Rose, Jocelyn K C; Fich, Eric A; Sun, Li; Domozych, David S; Fraser, Paul D; Tucker, Gregory A; Grierson, Don; Seymour, Graham B

    2016-01-01

    Controlling the rate of softening to extend shelf life was a key target for researchers engineering genetically modified (GM) tomatoes in the 1990s, but only modest improvements were achieved. Hybrids grown nowadays contain 'non-ripening mutations' that slow ripening and improve shelf life, but adversely affect flavor and color. We report substantial, targeted control of tomato softening, without affecting other aspects of ripening, by silencing a gene encoding a pectate lyase. © 2016 Nature America, Inc. All rights reserved.

  9. Influence of softening sequencing on electrocoagulation treatment of produced water.

    Science.gov (United States)

    Esmaeilirad, Nasim; Carlson, Ken; Omur Ozbek, Pinar

    2015-01-01

    Electrocoagulation has been used to remove solids and some metals from both water and wastewater sources for decades. Additionally, chemical softening is commonly employed in water treatment systems to remove hardness. This paper assesses the combination and sequence of softening and EC methods to treat hydraulic fracturing flowback and produced water from shale oil and gas operations. EC is one of the available technologies to treat produced water for reuse in frac fluids, eliminating not only the need to transport more water but also the costs of providing fresh water. In this paper, the influence of chemical softening on EC was studied. In the softening process, pH was raised to 9.5 and 10.2 before and after EC, respectively. Softening, when practiced before EC was more effective for removing turbidity with samples from wells older than one month (99% versus 88%). However, neither method was successful in treating samples collected from early flowback (1-day and 2-day samples), likely due to the high concentration of organic matter. For total organic carbon, hardness, Ba, Sr, and B removal, application of softening before EC appeared to be the most efficient approach, likely due to the formation of solids before the coagulation process. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Corrosion effects on soda lime glass

    NARCIS (Netherlands)

    Veer, F.A.; Rodichev, Y.M.

    2010-01-01

    Although soda lime glass is the most common used transparent material in architecture, little is known about the corrosion effects on long term strength and the interaction between corrosion and defects. Extensive testing on soda lime bars under different environmental conditions and different

  11. Hydrogen Chloride Reaction with Lime and Limestone

    DEFF Research Database (Denmark)

    Erik Weinell, Claus; Jensen, Peter I.; Dam-Johansen, Kim

    1992-01-01

    The capacity of solid slaked lime and limestone for binding HCl from a gas phase has been investigated in the temperature range 60-1000 °C. The binding capacity is largest in the range 500-600 °C. However, for slaked lime in the presence of water, a large binding capacity is observed also below 150...

  12. Simple Analysis of Historical Lime Mortars

    Science.gov (United States)

    Pires, Joa~o

    2015-01-01

    A laboratory experiment is described in which a simple characterization of a historical lime mortar is made by the determination of its approximate composition by a gravimetric method. Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) are also used for the qualitative characterization of the lime mortar components. These…

  13. Towards the industrial solar production of lime

    Energy Technology Data Exchange (ETDEWEB)

    Meier, A.; Bonaldi, E. [QualiCal SA, Bergamo (Italy); Cella, G.M. [QualiCal SA, Bergamo (Italy); Lipinski, W.; Palumbo, R.; Steinfeld, A. [ETH Zuerich (Switzerland) and PSI; Wieckert, C.; Wuillemin, D.

    2002-03-01

    A new industrial concept that aims at the development of the chemical engineering technology for the solar production of lime is being examined. To establish the technical feasibility, a 10 kW solar reactor has been designed, constructed, and experimentally tested at a high-flux solar furnace. The quality of the produced solar lime meets industrial standards. (author)

  14. Utilization of slaked lime for the regulation of pH value in the process of copper

    Directory of Open Access Journals (Sweden)

    Petković Aleksandar V.

    2009-01-01

    Full Text Available The investigations of used lime at plant from company Messer-Tehnogas, Belgrade, were in the aim to improvement technologically results from flotation concentration of copper minerals in flotation plant Veliki Krivelj. This paper shows usage of slaked lime, which is waste in the process of technical gas production, for regulation of pH value in the process of copper minerals flotation concentration. It is important to point out that slaked lime is a waste material that is not dangerous. Preparation and dosage includes preparation procedures, which enable introduction into flotation process with the aim of achieving better results. Lime from Limekiln Zagrađe is brought into four storage places in flotation. Volume of each storage place is 80 m3. Lime in pieces from storage place is added by airbladders on transportation line and by system of transportation lines lime gets to the ball mill. At the mill entrance water is added and then follows lime grinding. Milk glass of lime thus prepared goes to the pump basket from where is transported by pipeline to conditioner, and then by manual and (or automatic valves it is dosed to the flotation concentration of copper minerals process. Prospect of advancement and rationalization of the used lime in flotation plant Bor, Veliki Krivelj and Majdanpek as well as a way to link different branches of industry was demonstrated. Total cost of lime supplying, transporting, preparation and distribution related slaked lime is lower for 2.955 din/kg. Particularly, using lime from Messer in content of 2.1 g/l value of pH 11.82 is possible to obtain.

  15. LANDSCAPE ARCHAEOLOGY ALONG LIMES TRANSALUTANUS

    Directory of Open Access Journals (Sweden)

    Eugen S. Teodor

    2014-09-01

    Full Text Available The project addresses the historical monuments comprised in the longest Roman ‘linear defence’ structure present on the Romanian territory.Despite it being the longest, this historic structure is the least protected and the least known in its technical details. Was indeed Limes Transalutanus an incomplete limes (lacking civilian settlements, for example, an odd construction (a vallum without fossa, an early-alarm line rather than a proper defensive line? Taking on these historical and archaeological challenges, the team attempts to develop an investigation technology applicable to large scale archaeological landscapes - a full evaluation chain, involving aerial survey, surface survey, geophysical investigation, multispectral images analysis, statistic evaluation and archaeological diggings. This technological chain will be systematically applied on the whole length of the objective, that is, on a 155 km distance. The attempt to find answers to issues related to the earth works’ functionality, layout, structure, chronology and relation with adjacent sites will be grounded on exploring the relations of the monument with the surrounding environment, by focussing on finding methods to reconstruct the features of the ancient landscapes, like systematic drilling, palynological tests and toponymical studies.

  16. A multicentre randomised controlled trial and economic evaluation of ion-exchange water softeners for the treatment of eczema in children: the Softened Water Eczema Trial (SWET).

    Science.gov (United States)

    Thomas, K S; Koller, K; Dean, T; O'Leary, C J; Sach, T H; Frost, A; Pallett, I; Crook, A M; Meredith, S; Nunn, A J; Burrows, N; Pollock, I; Graham-Brown, R; O'Toole, E; Potter, D; Williams, H C

    2011-02-01

    To determine whether installation of an ion-exchange water softener in the home could improve atopic eczema in children and, if so, to establish its likely cost and cost-effectiveness. An observer-blind, parallel-group randomised controlled trial of 12 weeks duration followed by a 4-week observational period. Eczema was assessed by research nurses blinded to intervention at baseline, 4 weeks, 12 weeks and 16 weeks. The primary outcome was analysed as intent-to-treat, using the randomised allocation rather than actual treatment received. A secondary per-protocol analysis excluded participants who failed to receive their allocated treatment and who were deemed to be protocol violators. Secondary and primary care referral centres in England (UK) serving a variety of ethnic and social groups and including children living in both urban and periurban homes. Three hundred and thirty-six children (aged 6 months to 16 years) with moderate/severe atopic eczema, living in homes in England supplied by hard water (≥ 200 mg/l calcium carbonate). Participants were randomised to either installation of an ion-exchange water softener plus usual eczema care (group A) for 12 weeks or usual eczema care alone (group B) for 12 weeks. This was followed by a 4-week observational period, during which water softeners were switched off/removed from group A homes and installed in group B homes. Standard procedure was to soften all water in the home, but to provide mains (hard) water at a faucet-style tap in the kitchen for drinking and cooking. Participants were therefore exposed to softened water for bathing and washing of clothes, but continued to drink mains (hard) water. Usual care was defined as any treatment that the child was currently using in order to control his or her eczema. New treatment regimens used during the trial period were documented. Primary outcome was the difference between group A and group B in mean change in disease severity at 12 weeks compared with baseline, as

  17. Earth mortars and earth-lime renders

    Directory of Open Access Journals (Sweden)

    Maria Fernandes

    2008-01-01

    Full Text Available Earth surface coatings play a decorative architectural role, apart from their function as wall protection. In Portuguese vernacular architecture, earth mortars were usually applied on stone masonry, while earth renders and plasters were used on indoors surface coatings. Limestone exists only in certain areas of the country and consequently lime was not easily available everywhere, especially on granite and schist regions where stone masonry was a current building technique. In the central west coast of Portugal, the lime slaking procedure entailed slaking the quicklime mixed with earth (sandy soil, in a pit; the resulting mixture would then be combined in a mortar or plaster. This was also the procedure for manufactured adobes stabilized with lime. Adobe buildings with earth-lime renderings and plasters were also traditional in the same region, using lime putty and lime wash for final coat and decoration. Classic decoration on earth architecture from the 18th-19th century was in many countries a consequence of the François Cointeraux (1740-1830 manuals - Les Cahiers d'Architecture Rurale" (1793 - a French guide for earth architecture and building construction. This manual arrived to Portugal in the beginning of XIX century, but was never translated to Portuguese. References about decoration for earth houses were explained on this manual, as well as procedures about earth-lime renders and ornamentation of earth walls; in fact, these procedures are exactly the same as the ones used in adobe buildings in this Portuguese region. The specific purpose of the present paper is to show some cases of earth mortars, renders and plasters on stone buildings in Portugal and to explain the methods of producing earth-lime renders, and also to show some examples of rendering and coating with earth-lime in Portuguese adobe vernacular architecture.

  18. Steam slaking of lime - kinetics and technology. New energy effective lime slaking technology in kraft pulping; Aangslaeckning av kalk - kinetik och teknik. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Roland

    2008-06-15

    Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional lime burning and slaking methods are that heat recovery is bad and heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant, and to recover heat at higher temperatures. The forecasted method means that lime is slaked with water vapour, for example combined with an indirect heated lime mud drier and a lime kiln. This project is a follow-up to pilot tests performed in a specific machine equipment at year 2006. The target group is pulp and paper industry using the kraft process. The owner of this new project is Carnot AB and the project is performed inside the Vaermeforsk Program for Pulp and Paper Industry 2006-2008. Partners and advisers in project group have been KTH Energy Processes, CTH Energy and Environment, LTH Chemical Technology, SMA Mineral AB, and reference group from STORA Enso Skoghall, Sodra Cell, M-Real Husum and SCA Packaging Piteaa. The task in this stage has included market investigations and laboratory tests. Contacts have been made with suppliers, preliminary dimensioning of process equipment and budget offers are received. Economic calculations have been made out of the offers. The laboratory tests are done as an examination paper at KTH Energiprocesser on the reactivity of burned lime from kraft lime kiln when it is slaked with water vapour instead of green liquor. The vapour intended to be used is at atmospheric pressure or even down to 0,2 atm. Complementary addition to these laboratory

  19. Removal of Strontium from Drinking Water by Conventional Treatment and Lime Softening in Bench-Scale Studies

    Science.gov (United States)

    The United States Environmental Protection Agency Contaminant Candidate List 3 lists strontium as a contaminant for potential regulatory consideration in drinking water. There is very little data available on strontium removal from drinking water. As a result, there is an immedia...

  20. The antifungal efficiency of carbide lime slurry compared with the commercial lime efficiency

    Science.gov (United States)

    Strigac, J.; Mikusinec, J.; Strigacova, J.; Stevulova, N.

    2017-10-01

    The article deals with studying the antifungal efficiency of carbide lime slurry compared to industrially manufactured commercial lime. Antifungal efficiency expressed as mould proofness properties was tested on the fungi using the procedure given in standard CSN 72 4310. A mixture of fungi Aspergillus niger, Chaetomium globosum, Penicillium funiculosum, Paecilomyces variotii and Gliocladium virens was utilized for testing. The scale for evaluating mould proofness properties according to CSN 72 4310 is from 0 to 5 in degree of fungi growth, where 0 means that no fungi growth occurs and the building products and materials possess fungistatic properties. The study confirms the fungistatic propeties of carbide lime slurry as well as industrially manufactured commercial lime. However, carbide lime slurry and industrially manufactured commercial lime possess no fungicidal effect.

  1. Lime kiln dust as a potential raw material in portland cement manufacturing

    Science.gov (United States)

    Miller, M. Michael; Callaghan, Robert M.

    2004-01-01

    In the United States, the manufacture of portland cement involves burning in a rotary kiln a finely ground proportional mix of raw materials. The raw material mix provides the required chemical combination of calcium, silicon, aluminum, iron, and small amounts of other ingredients. The majority of calcium is supplied in the form of calcium carbonate usually from limestone. Other sources including waste materials or byproducts from other industries can be used to supply calcium (or lime, CaO), provided they have sufficiently high CaO content, have low magnesia content (less than 5 percent), and are competitive with limestone in terms of cost and adequacy of supply. In the United States, the lime industry produces large amounts of lime kiln dust (LKD), which is collected by dust control systems. This LKD may be a supplemental source of calcium for cement plants, if the lime and cement plants are located near enough to each other to make the arrangement economical.

  2. Subgrade stabilization alternatives to lime and cement.

    Science.gov (United States)

    2010-04-15

    This project involved four distinct research activities, (1) the influence of temperature on lime-stabilized soils, (2) the influence of temperature on cement-stabilized soils (3) temperature modeling of stabilized subgrade and (4) use of calcium chl...

  3. Modification of Lime Mortars with Synthesized Aluminosilicates

    Science.gov (United States)

    Loganina, Valentina I.; Sadovnikova, Marija E.; Jezierski, Walery; Małaszkiewicz, Dorota

    2017-10-01

    The increasing attention for restoration of buildings of historical and architectural importance has increased the interest for lime-based binders, which could be applied for manufacturing repair mortars and plasters compatible with historical heritage. Different additives, admixtures or fibers may be incorporated to improve mechanical and thermal features of such materials. In this study synthesized aluminosilicates (SA) were applied as an additive for lime mortar. The technology of synthesis consisted in the deposition of aluminosilicates from a sodium liquid glass by the aluminum sulphate Al2(SO4)3. The goal of this investigation was developing a new method of aluminosilicates synthesis from a sodium liquid glass and using this new material as a component for a lime mortar. Aluminosilicates were precipitated from the solution of aluminum sulphate Al2(SO)3 and sodium silicate. SA were then used as an additive to calcareous compositions and their influence was tested. Mortars were prepared with commercial air lime and siliceous river sand. Air lime binder was replaced by 5 and 10 wt.% of SA. Calcareous composition specimens were formed at water/lime ratio 1.0. The following analyses were made: grain size distribution of SA, X-ray diffraction analysis (XRD), sorption properties, plastic strength and compressive strength of lime mortars. XRD pattern of the SA shows the presence of thenardite, gibbsite and amorphous phase represented by aggregate of nano-size cristobalite-like crystallites. Application of SA leads to increase of compressive strength after 90 days of hardening by 28% and 53% at SA content 5 and 10% respectively comparing to specimens without this additive. Contents of chemically bound lime in the reference specimens after 28 days of hardening in air-dry conditions was 46.5%, while in specimens modified with SA contained 50.0-55.3% of bound lime depending on filtrate pH. This testifies to high activity of calcareous composition. The new blended lime

  4. Pregnancy Constipation: Are Stool Softeners Safe?

    Science.gov (United States)

    ... lifestyle changes. For example: Drink plenty of fluids. Water is a good choice. Prune juice also can help. Include physical activity in your daily routine. Being active can help prevent pregnancy constipation. Include more fiber in your diet. Choose high- ...

  5. Recycled sand in lime-based mortars.

    Science.gov (United States)

    Stefanidou, M; Anastasiou, E; Georgiadis Filikas, K

    2014-12-01

    The increasing awareness of the society about safe guarding heritage buildings and at the same time protecting the environment promotes strategies of combining principles of restoration with environmentally friendly materials and techniques. Along these lines, an experimental program was carried out in order to investigate the possibility of producing repair, lime-based mortars used in historic buildings incorporating secondary materials. The alternative material tested was recycled fine aggregates originating from mixed construction and demolition waste. Extensive tests on the raw materials have been performed and mortar mixtures were produced using different binding systems with natural, standard and recycled sand in order to compare their mechanical, physical and microstructure properties. The study reveals the improved behavior of lime mortars, even at early ages, due to the reaction of lime with the Al and Si constituents of the fine recycled sand. The role of the recycled sand was more beneficial in lime mortars rather than the lime-pozzolan or lime-pozzolan-cement mortars as a decrease in their performance was recorded in the latter cases due to the mortars' structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. Balancing guava nutrition with liming and fertilization

    Directory of Open Access Journals (Sweden)

    Amanda Hernandes

    2012-12-01

    Full Text Available Guava response to liming and fertilization can be monitored by tissue testing. Tissue nutrient signature is often diagnosed against nutrient concentration standards. However, this approach has been criticized for not considering nutrient interactions and to generate numerical biases as a result of data redundancy, scale dependency and non-normal distribution. Techniques of compositional data analysis can control those biases by balancing groups of nutrients, such as those involved in liming and fertilization. The sequentially arranged and orthonormal isometric log ratios (ilr or balances avoid numerical bias inherent to compositional data. The objectives were to relate tissue nutrient balances with the production of "Paluma" guava orchards differentially limed and fertilized, and to adjust the current patterns of nutrient balance with the range of more productive guava trees. It was conducted one experiment of 7-yr of liming and three experiments of 3-yr with N, P and K trials in 'Paluma' orchards on an Oxisol. Plant N, P, K, Ca and Mg were monitored yearly. It was selected the [N, P, K | Ca, Mg], [N, P | K], [N | P] and [Ca | Mg] balances to set apart the effects of liming (Ca-Mg and fertilizers (N-K on macronutrient balances. Liming largely influenced nutrient balances of guava in the Oxisol while fertilization was less influential. The large range of guava yields and nutrient balances allowed defining balance ranges and comparing them with the critical ranges of nutrient concentration values currently used in Brazil and combined into ilr coordinates.

  7. Influence of liquid temperature and flow rate on enamel erosion and surface softening.

    Science.gov (United States)

    Eisenburger, M; Addy, M

    2003-11-01

    Enamel erosion and softening are based on chemical processes which could be influenced by many factors including temperature and acid flow rate. Knowledge of the influence of these variables could have relevance to research experiments and clinical outcomes. Both parameters were investigated using an ultrasonication and profilometry method to assess erosion depth and surface softening of enamel. The influence of temperature was studied by eroding polished human enamel samples at 4, 20, 35 or 50 degrees C for 2 h. Secondly, different liquid flow conditions were established by varying acid agitation. Additionally, a slow laminar flow and a jet of citric acid, to simulate drinking through a straw, were applied to specimens. Erosion depth increased significantly with acid temperature from 11.0 microm at 4 degrees C to 35.8 microm at 50 degrees C. Surface softening increased much more slowly and plateaued at 2.9 microm to 3.5 microm after 35 degrees C. A strong dependence of erosion on liquid flow was revealed. In unstirred conditions only 8.6 microm erosion occurred, which increased to 22.2 microm with slow stirring and 40.9 microm with fast stirring. Surface softening did not increase correspondingly with its largest extent at slow stirring at 3.4 microm.The implication of these data are: first, the conditions for erosion experiments in vitro or in situ need to be specified for reliable comparisons between studies. Secondly, erosion of teeth by soft drinks are likely to be influenced both by the temperature of the drink and individual drinking habits.

  8. Metadynamic and static recrystallization softening behavior of a bainite steel

    Science.gov (United States)

    Li, Lixin; Zheng, Liangyu; Ye, Ben; Tong, Zeqiong

    2018-01-01

    The metadynamic recrystallization (MDRX) and static recrystallization (SRX) softening behavior of a bainite steel was investigated by two-pass isothermal compression experiments at temperatures of 1173, 1273, 1373, and 1473 K and strain rates of 0.01, 0.1, 1, and 10 s-1 with inter-pass times of 1, 5, 10, and 30 s on a Gleeble-1500 thermo-mechanical simulator. Kinetic equations were developed to evaluate the softening fractions caused by MDRX and SRX. A comparison between the experimental and predicted softening fractions showed that the proposed kinetic equations can provide a precise estimation of the MDRX and SRX behavior of the studied steel. The results based on the kinetic equations indicated that the MDRX and SRX softening fraction increases with the increase in strain rate, deformation temperature, inter-pass time, and pre-strain; the activation energy of MDRX is much smaller than that of SRX; and the no-recrystallization temperature of the investigated steel is 1179.4 K.

  9. Stress-Softening and Residual Strain Effects in Suture Materials

    Directory of Open Access Journals (Sweden)

    Alex Elías-Zúñiga

    2013-01-01

    Full Text Available This work focuses on the experimental characterization of suture material samples of MonoPlus, Monosyn, polyglycolic acid, polydioxanone 2–0, polydioxanone 4–0, poly(glycolide-co-epsilon-caprolactone, nylon, and polypropylene when subjected to cyclic loading and unloading conditions. It is found that all tested suture materials exhibit stress-softening and residual strain effects related to the microstructural material damage upon deformation from the natural, undistorted state of the virgin suture material. To predict experimental observations, a new constitutive material model that takes into account stress-softening and residual strain effects is developed. The basis of this model is the inclusion of a phenomenological nonmonotonous softening function that depends on the strain intensity between loading and unloading cycles. The theory is illustrated by modifying the non-Gaussian average-stretch, full-network model to capture stress-softening and residual strains by using pseudoelasticity concepts. It is shown that results obtained from theoretical simulations compare well with suture material experimental data.

  10. An introduction to LIME 1.0 and its use in coupling codes for multiphysics simulations.

    Energy Technology Data Exchange (ETDEWEB)

    Belcourt, Noel; Pawlowski, Roger Patrick; Schmidt, Rodney Cannon; Hooper, Russell Warren

    2011-11-01

    LIME is a small software package for creating multiphysics simulation codes. The name was formed as an acronym denoting 'Lightweight Integrating Multiphysics Environment for coupling codes.' LIME is intended to be especially useful when separate computer codes (which may be written in any standard computer language) already exist to solve different parts of a multiphysics problem. LIME provides the key high-level software (written in C++), a well defined approach (with example templates), and interface requirements to enable the assembly of multiple physics codes into a single coupled-multiphysics simulation code. In this report we introduce important software design characteristics of LIME, describe key components of a typical multiphysics application that might be created using LIME, and provide basic examples of its use - including the customized software that must be written by a user. We also describe the types of modifications that may be needed to individual physics codes in order for them to be incorporated into a LIME-based multiphysics application.

  11. Improved control of sucrose losses and clarified juice turbidity with lime saccharate in hot lime clarification of sugarcane juice and other comparisons with milk of lime

    Science.gov (United States)

    A comparative investigation of adding milk of lime (MOL) versus lime saccharate (SACCH) in hot lime clarification of juice at a U.S. sugarcane factory was undertaken to quantify performance across the 2009 processing season after a preliminary factory study in 2008. SACCH was prepared by adding hyd...

  12. Experimental study and simulation of cyclic softening of tempered martensite ferritic steels

    International Nuclear Information System (INIS)

    Giroux, P.-F.

    2011-01-01

    The present work focuses on the high temperature mechanical behaviour of 9% Cr tempered martensite steels, considered as potential candidates for structural components in the next Generation IV nuclear power plants. Already used for energy production in fossil power plants, they are sensitive to softening during high-temperature cycling and creep-fatigue. This phenomenon is coupled to a pronounced microstructural degradation: mainly vanishing of subgrain boundaries and decrease in dislocation density. This study aims at (i) linking the macroscopic cyclic softening of 9% Cr steels and their microstructural evolution during cycling and (ii) proposing a physically-based modelling of deformation mechanisms in order to predict the macroscopic mechanical behaviour of these steels during cycling. Mechanical study includes uniaxial tensile and cyclic test at 550 C performed on a Grade 92 steel (9Cr-0,5Mo-1,8W-V-Nb). The effect of both strain amplitude and rate on mechanical behaviour is studied. Examination of tensile specimens suggests that the physical mechanism responsible for slight measured softening is mainly the necking phenomenon and the evolution of mean subgrain size, which increases by more than 15 % compared to the as-received state. The evolution of the macroscopic stress during cycling shows that cyclic softening is due to the decrease in kinematic stress. TEM observations highlights that the mean subgrain size increases by 60 to 100 % while the dislocation density decreases by more than 50 % during cycling, compared to the as-received state. A self-consistent homogenization model based on crystalline elasto-visco-plasticity and dislocation densities, predicting the mechanical behaviour of the material and its microstructural evolution during deformation is proposed. This model takes some of the main physical deformation mechanisms into account and only the two parameters of crystalline visco-plasticity should be adjusted (the effective activation energy and

  13. Study of sticky rice-lime mortar technology for the restoration of historical masonry construction.

    Science.gov (United States)

    Yang, Fuwei; Zhang, Bingjian; Ma, Qinglin

    2010-06-15

    Replacing or repairing masonry mortar is usually necessary in the restoration of historical constructions, but the selection of a proper mortar is often problematic. An inappropriate choice can lead to failure of the restoration work, and perhaps even further damage. Thus, a thorough understanding of the original mortar technology and the fabrication of appropriate replacement materials are important research goals. Many kinds of materials have been used over the years in masonry mortars, and the technology has gradually evolved from the single-component mortar of ancient times to hybrid versions containing several ingredients. Beginning in 2450 BCE, lime was used as masonry mortar in Europe. In the Roman era, ground volcanic ash, brick powder, and ceramic chip were added to lime mortar, greatly improving performance. Because of its superior properties, the use of this hydraulic (that is, capable of setting underwater) mortar spread, and it was adopted throughout Europe and western Asia. Perhaps because of the absence of natural materials such as volcanic ash, hydraulic mortar technology was not developed in ancient China. However, a special inorganic-organic composite building material, sticky rice-lime mortar, was developed. This technology was extensively used in important buildings, such as tombs, in urban constructions, and even in water conservancy facilities. It may be the first widespread inorganic-organic composite mortar technology in China, or even in the world. In this Account, we discuss the origins, analysis, performance, and utility in historic preservation of sticky rice-lime mortar. Mortar samples from ancient constructions were analyzed by both chemical methods (including the iodine starch test and the acid attack experiment) and instrumental methods (including thermogravimetric differential scanning calorimetry, X-ray diffraction, Fourier transform infrared, and scanning electron microscopy). These analytical results show that the ancient masonry

  14. Modification of Textile Materials' Surface Properties Using Chemical Softener

    Directory of Open Access Journals (Sweden)

    Jurgita KOŽENIAUSKIENĖ

    2011-03-01

    Full Text Available In the present study the effect of technological treatment involving the processes of washing or washing and softening with chemical cationic softener "Surcase" produced in Great Britain on the surface properties of cellulosic textile materials manufactured from cotton, bamboo and viscose spun yarns was investigated. The changes in textile materials surface properties were evaluated using KTU-Griff-Tester device and FEI Quanta 200 FEG scanning electron microscope (SEM. It was observed that the worst hand properties and the higher surface roughness are observed of cotton materials if compared with those of bamboo and viscose materials. Also, it was shown that depending on the material structure the handle parameters of knitted materials are the better than the ones of woven fabrics.http://dx.doi.org/10.5755/j01.ms.17.1.249

  15. Hardening by annealing and softening by deformation in nanostructured metals

    DEFF Research Database (Denmark)

    Huang, X.; Hansen, N.; Tsuji, N.

    2006-01-01

    We observe that a nanostructured metal can be hardened by annealing and softened when subsequently deformed, which is in contrast to the typical behavior of a metal. Microstructural investigation points to an effect of the structural scale on fundamental mechanisms of dislocation-dislocation and ......We observe that a nanostructured metal can be hardened by annealing and softened when subsequently deformed, which is in contrast to the typical behavior of a metal. Microstructural investigation points to an effect of the structural scale on fundamental mechanisms of dislocation....... As a consequence, the strength decreases and the ductility increases. These observations suggest that for materials such as the nanostructured aluminum studied here, deformation should be used as an optimizing procedure instead of annealing....

  16. Lime in gold and uranium mining

    International Nuclear Information System (INIS)

    Van Staden, C.M.

    1979-01-01

    In this article the author discusses the role of lime in gold and uranium extraction and looks more closely at the industry's efforts to improve the environment by vegetation of sand dumps and slimes dams. He then comes to the conclusion that lime has been and still is the most effective, practical and cheapest chemical that can be used in the South African gold and uranium mining industry to settle pulps, protect cyanide solutions, aid the vegetation of dumps and neutralise acidic waters and residues. The gold and uranium industry is very pollution concious, and in South Africa the importance of the role that lime plays in combating air and water pollution cannot be over emphasised

  17. Pemanfaatan ter sebagai softener dalam pembuatan karet riklim

    Directory of Open Access Journals (Sweden)

    Arum Yuniari

    2006-07-01

    Full Text Available The aims of this research was to study the effect of Coal Tar as softener for reclaim rubber production from waste of rubber of tyre rethreading as input materials was scrap rubber. Coal Tar as softener was used with variation; 2,5; 5; 7,5; 10; 12,5 and 15% respectively from total scrap rubber. Reclaimed rubber was made at temperature 1200C for 1 hour in autoclave and than it was subsequently ground with two rolls mills. The characteristics of the reclaimed rubber was tested for the vulcanization and physical properties. The results showed that Coal Tar could be utilized as softener for reclaimed rubber. Reclaimed rubber production containing Coal Tar 15% would give good vulcanization and physical properties. The vulcanization 1062 seconds, maximum torque 39,08 kgf-cm, minimum torque 4,71 kgf-cm. Good physical properties : tensile strength 80,74 kg/cm2 elongation at break 444,62%, hardness 49 shore A, tear strength 40,39 kg/cm, density 1,15 g/cm3, abrasion resistance 1,87 mm3/kgm, and no crack detected on the flex cracking test of 150 kcs

  18. The Use of Fly Ash and Lime Sludge as Partial Replacement of Cement in Mortar

    Directory of Open Access Journals (Sweden)

    Vaishali Sahu

    2014-01-01

    Full Text Available The increased demand of drinking water and power has led huge generation of water treatment plant residue i.e. sludge and the thermal power plant by-product such as fly ash. Large quantities of sludge and fly ash are produced in India and disposed off by landfilling or dumping in and around sites. In this study fly ash and water softening sludge (lime sludge has been utilized in mortar. Two types of mortar (type I and II with four binder combinations have been tried. Binder I consists of 70% fly ash (FA and 30% lime sludge (LS , 0 % gypsum (G, binder II is 70% FA, 30% LS and 1% G, binder III is 50% FA, 30% LS and 20% cement and the binder IV is 40% FA, 40% LS with 20% cement. The effect of various combinations on strength has been discussed here. This paper outlines the composition of the composite material, method of preparation of mortar specimen, testing procedure and salient results thereof.

  19. Long-term effects of hydrated lime and quicklime on the decay of human remains using pig cadavers as human body analogues: Field experiments.

    Science.gov (United States)

    Schotsmans, Eline M J; Fletcher, Jonathan N; Denton, John; Janaway, Robert C; Wilson, Andrew S

    2014-05-01

    An increased number of police enquiries involving human remains buried with lime have demonstrated the need for more research into the effect of different types of lime on cadaver decomposition and its micro-environment. This study follows previous studies by the authors who have investigated the effects of lime on the decay of human remains in laboratory conditions and 6 months of field experiments. Six pig carcasses (Sus scrofa), used as human body analogues, were buried without lime with hydrated lime (Ca(OH)2) and quicklime (CaO) in shallow graves in sandy-loam soil in Belgium and recovered after 17 and 42 months of burial. Analysis of the soil, lime and carcasses included entomology, pH, moisture content, microbial activity, histology and lime carbonation. The results of this study demonstrate that despite conflicting evidence in the literature, the extent of decomposition is slowed down by burial with both hydrated lime and quicklime. The more advanced the decay process, the more similar the degree of liquefaction between the limed and unlimed remains. The end result for each mode of burial will ultimately result in skeletonisation. This study has implications for the investigation of clandestine burials, for a better understanding of archaeological plaster burials and potentially for the interpretation of mass graves and management of mass disasters by humanitarian organisation and DVI teams. Copyright © 2014. Published by Elsevier Ireland Ltd.

  20. Lime stabilization of fine-grained sediments in western Greenland

    DEFF Research Database (Denmark)

    Jørgensen, Anders Stuhr; Ingeman-Nielsen, Thomas; Skels, Peteris

    2011-01-01

    Thick deposits of fine-grained marine sediments exist in large areas of western Greenland. Many places these sediments are located above sea-level, and now complicate construction projects in urban areas. The mineralogy of the fine-grained sediments is very different from European sediments, mainly...... due to the cold climate, and it is therefore of great interest to study possible methods to improve the stability and strength properties. This project includes laboratory studies of lime stabilization on fine-grained marine sediments from Kangerlussuaq, western Greenland. The results have included...

  1. 27 CFR 9.27 - Lime Kiln Valley.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Lime Kiln Valley. 9.27... OF THE TREASURY LIQUORS AMERICAN VITICULTURAL AREAS Approved American Viticultural Areas § 9.27 Lime Kiln Valley. (a) Name. The name of the viticultural area described in this section is “Lime Kiln Valley...

  2. 46 CFR 148.04-23 - Unslaked lime in bulk.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Unslaked lime in bulk. 148.04-23 Section 148.04-23... HAZARDOUS MATERIALS IN BULK Special Additional Requirements for Certain Material § 148.04-23 Unslaked lime in bulk. (a) Unslaked lime in bulk must be transported in unmanned, all steel, double-hulled barges...

  3. Fertilizer and Lime: Why They Are Used.

    Science.gov (United States)

    McCaslin, Judith Strand

    This unit teaching guide is designed to help teachers explain the principles of fertilizer and lime use. The first of four major sections is a teaching outline keyed to transparency masters and student handouts. Thirteen major areas are covered in the teaching outline: (1) plant needs; (2) uses of fertilizer; (3) nutrients for plant growth; (4)…

  4. Peat Soil Stabilization using Lime and Cement

    Directory of Open Access Journals (Sweden)

    Mohd Zambri Nadhirah

    2018-01-01

    Full Text Available This paper presents a study of the comparison between two additive Lime and Cement for treating peat soil in term of stabilization. Peat and organic soils are commonly known for their high compressibility, extremely soft, and low strength. The aim of this paper is to determine the drained shear strength of treated peat soil from Perlis for comparison purposes. Direct Shear Box Test was conducted to obtain the shear strength for all the disturbed peat soil samples. The quick lime and cement was mixed with peat soil in proportions of 10% and 20% of the dry weight peat soil. The experiment results showed that the addition of additives had improved the strength characteristics of peat soil by 14% increment in shear strength. In addition, the mixture of lime with peat soil yield higher result in shear strength compared to cement by 14.07% and 13.5% respectively. These findings indicate that the lime and cement is a good stabilizer for peat soil, which often experienced high amount of moisture content.

  5. Peat Soil Stabilization using Lime and Cement

    Science.gov (United States)

    Zambri, Nadhirah Mohd; Ghazaly, Zuhayr Md.

    2018-03-01

    This paper presents a study of the comparison between two additive Lime and Cement for treating peat soil in term of stabilization. Peat and organic soils are commonly known for their high compressibility, extremely soft, and low strength. The aim of this paper is to determine the drained shear strength of treated peat soil from Perlis for comparison purposes. Direct Shear Box Test was conducted to obtain the shear strength for all the disturbed peat soil samples. The quick lime and cement was mixed with peat soil in proportions of 10% and 20% of the dry weight peat soil. The experiment results showed that the addition of additives had improved the strength characteristics of peat soil by 14% increment in shear strength. In addition, the mixture of lime with peat soil yield higher result in shear strength compared to cement by 14.07% and 13.5% respectively. These findings indicate that the lime and cement is a good stabilizer for peat soil, which often experienced high amount of moisture content.

  6. Lime Kiln Modeling. CFD and One-dimensional simulations

    Energy Technology Data Exchange (ETDEWEB)

    Svedin, Kristoffer; Ivarsson, Christofer; Lundborg, Rickard

    2009-03-15

    The incentives for burning alternative fuels in lime kilns are growing. An increasing demand on thorough investigations of alternative fuel impact on lime kiln performance have been recognized, and the purpose of this project has been to develop a lime kiln CFD model with the possibility to fire fuel oil and lignin. The second part of the project consists of three technical studies. Simulated data from a one-dimensional steady state program has been used to support theories on the impact of biofuels and lime mud dryness. The CFD simulations was carried out in the commercial code FLUENT. Due to difficulties with the convergence of the model the calcination reaction is not included. The model shows essential differences between the two fuels. Lignin gives a different flame shape and a longer flame length compared to fuel oil. Mainly this depends on how the fuel is fed into the combustion chamber and how much combustion air that is added as primary and secondary air. In the case of lignin combustion the required amount of air is more than in the fuel oil case. This generates more combustion gas and a different flow pattern is created. Based on the values from turbulent reaction rate for the different fuels an estimated flame length can be obtained. For fuel oil the combustion is very intense with a sharp peak in the beginning and a rapid decrease. For lignin the combustion starts not as intense as for the fuel oil case and has a smoother shape. The flame length appears to be approximately 2-3 meter longer for lignin than for fuel oil based on turbulent reaction rate in the computational simulations. The first technical study showed that there are many benefits of increasing dry solids content in the lime mud going into a kiln such as increased energy efficiency, reduced TRS, and reduced sodium in the kiln. However, data from operating kilns indicates that these benefits can be offset by increasing exit gas temperature that can limit kiln production capacity. Simulated

  7. The Stabilization of Weathered Dolerite Aggregates with Cement, Lime, and Lime Fly Ash for Pavement Construction

    Directory of Open Access Journals (Sweden)

    Felix N. Okonta

    2014-01-01

    Full Text Available An experimental program was performed on weathered dolerite specimens stabilized by adding varying percentages of cement (4, 8, 12, and 16 % and lime (6 and 12 % and a combination of lime and fly ash (6% lime + 12% Fly ash and 12% lime + 12% Fly ash % by dry weight of soil. The strength was examined under three different curing methods, namely, membrane curing (MBC, alternate moist-air curing (MAC, and water curing (WAC, by conducting unconfined compressive strength (UCS tests. Simple polynomial and linear functions (regression models were used to define the relationships between the variables investigated. Membrane curing (MBC gave results close enough to the water curing (WAC to indicate that it can be confidently used on the field during pavement construction. From the results obtained, for class B (interurban collector and major rural roads pavement construction, addition of 8% cement was recommended for road base construction with stabilized WDA. Also the addition of 12 + 12% Lime and Fly Ash was recommended for road subbase construction with stabilized WDA. Stabilized WDA against the prejudiced myths would perform satisfactorily for base and subbase construction in both heavily trafficked and low volume roads with economic quantities of cement, lime, and fly ash in South Africa.

  8. Application of lime and urea and its effect on development of Phythophthora palmivora.

    Directory of Open Access Journals (Sweden)

    Sakti Widyanta Pratama

    2015-03-01

    Full Text Available Black pod rot disease (BPRD which is caused by Phytophthora palmivora is one of the main diseases of cocoa cultivations particularly in plantations with wet climate. Black pod rot can develop rapidly under high humidity environments, particularly during rainy seasons. This disease can cause loss of harvest of up to 46.63% in East Java. The various control efforts attempted so far have not resulted in significant improvements. Urea, in addition to functioning as fertilizer, can also produce the ammonia gas which is believed to be able to suppress black pod rot. This research aims to determine the effectiveness of black pod rot control using the combination of lime and urea. This research was conducted from June to September 2013. The materials used in test included sterile soil, black pod rot infected cocoa, urea, and agricultural lime. Observation results showed that ammonia could form from urea. Lime can increase the speed of the formation. The ammonia gas forming from 0.06% urea and 0.3% lime can control the P. palmivora fungus inside the soil. Key words: Pod rot, P. palmivora, urea, lime, ammonia

  9. Quantitative assessment of cervical softening during pregnancy in the Rhesus macaque with shear wave elasticity imaging

    Science.gov (United States)

    Rosado-Mendez, Ivan M.; Carlson, Lindsey C.; Woo, Kaitlin M.; Santoso, Andrew P.; Guerrero, Quinton W.; Palmeri, Mark L.; Feltovich, Helen; Hall, Timothy J.

    2018-04-01

    Abnormal parturition, e.g. pre- or post-term birth, is associated with maternal and neonatal morbidity and increased economic burden. This could potentially be prevented by accurate detection of abnormal softening of the uterine cervix. Shear wave elasticity imaging (SWEI) techniques that quantify tissue softness, such as shear wave speed (SWS) measurement, are promising for evaluation of the cervix. Still, interpretation of results can be complicated by biological variability (i.e. spatial variations of cervix stiffness, parity), as well as by experimental factors (i.e. type of transducer, posture during scanning). Here we investigated the ability of SWEI to detect cervical softening, as well as sources of SWS variability that can affect this task, in the pregnant and nonpregnant Rhesus macaque. Specifically, we evaluated SWS differences when imaging the cervix transabdominally with a typical linear array abdominal transducer, and transrectally with a prototype intracavitary linear array transducer. Linear mixed effects (LME) models were used to model SWS as a function of menstrual cycle day (in nonpregnant animals) and gestational age (in pregnant animals). Other variables included parity, shear wave direction, and cervix side (anterior versus posterior). In the nonpregnant cervix, the LME model indicated that SWS increased by 2% (95% confidence interval 0–3%) per day, starting eight days before menstruation. During pregnancy, SWS significantly decreased at a rate of 6% (95% CI 5–7%) per week (intracavitary approach) and 3% (95% CI 2–4%) per week (transabdominal approach), and interactions between the scanning approach and other fixed effects were also significant. These results suggest that, while absolute SWS values are influenced by factors such as scanning approach and SWEI implementation, these sources of variability do not compromise the sensitivity of SWEI to cervical softening. Our results also highlight the importance of standardizing SWEI

  10. Development of Tensile Softening Model for Plain Concrete

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.K.; Song, Y.C. [Korea Electric Power Research Institute, Taejon (Korea)

    2002-07-01

    Large-scale direct tensile softenng tests using plate concrete specimens(4000, 5000psi) with notch were performed under uniaxial stress. There were presented the basic physical properties and the complete load-CMOD(Crack Mouth Opening Displacement) curves for them And them the fracture energy was evaluated using the complete load-CMOD curves respectively, and there was presents optimal tensile softening model which is modified by a little revision of an existing one. Therefore, here provided the real verification data through the tests for developing other nonlinear concrete finite element models. (author). 32 refs., 38 figs., 4 tabs.

  11. Softening the supersymmetric flavor problem in orbifold grand unified theories

    International Nuclear Information System (INIS)

    Kajiyama, Yuji; Terao, Haruhiko; Kubo, Jisuke

    2004-01-01

    The infrared attractive force of the bulk gauge interactions is applied to soften the supersymmetric flavor problem in the orbifold SU(5) grand unified theory of Kawamura. Then this force aligns in the infrared regime the soft supersymmetry breaking terms out of their anarchical disorder at a fundamental scale, in such a way that flavor-changing neutral currents as well as dangerous CP-violating phases are suppressed at low energies. It is found that this dynamical alignment is sufficiently good compared with the current experimental bounds, as long as the diagonalization matrices of the Yukawa couplings are CKM-like

  12. Effect of hot-air drying on the physicochemical properties of kaffir lime leaves (Citrus hystrix)

    OpenAIRE

    Juhari, Nurul Hanisah Binti; Lasekan, Ola; Muhammad, Kharidah; Karim, Shahrim

    2013-01-01

    The effect of hot-air drying namely drying time (3-15 h), drying temperature (40-80°C) and loading capacity (0.5-2.0 kg/m2 ) on the physicochemical characteristics of kaffir lime leaves was optimized using Response Surface Methodology. Twenty treatments were assigned based on the second- order CCD including 6 center points, 6 axial points and 8 factorial points. The quality of dried kaffir lime leaves was evaluated by determining moisture content, water activity, texture (brittleness) and Hun...

  13. Internal friction and elastic softening in polycrystalline Nb3Sn

    International Nuclear Information System (INIS)

    Bussiere, J.F.; Faucher, B.; Snead, C.L. Jr.; Welch, D.O.

    1981-01-01

    The vibrating-reed technique was used to measure internal friction and Young's modulus of polycrystalline Nb 3 Sn in the form of composite Nb/Nb 3 Sn tapes from 6 to 300 K. In tapes with only small residual strain in the A15 layers, a dramatic increase in internal friction with decreasing temperature is observed with an abrupt onset at approx.48 K. The internal friction Q -1 between 6 and 48 K is believed to be associated with stress-induced motion of martensitic-domain walls. In this temperature range, Q -1 is approximately proportional to the square of the tetragonal strain of the martensitic phase; Q -1 α (c/a-1) 2 . With residual compressive strains of approx.0.2%, the internal friction associated with domain-wall motion is considerably reduced. This is attributed to a biasing of domain-wall orientation with residual stress, which reduces wall motion induced by the (much smaller) applied stress. The transformation temperature, however, is unchanged (within +- 1 K) by residual strains of up to 0.2%. Young's modulus exhibits substantial softening on cooling from 300 to 6 K. This softening, is substantially reduced in the presence of small residual compressive strains, indicating a highly nonlinear stress-strain relationship as previously reported for V 3 Si

  14. Effect of the preparation of lime putties on their properties.

    Science.gov (United States)

    Navrátilová, Eva; Tihlaříková, Eva; Neděla, Vilém; Rovnaníková, Pavla; Pavlík, Jaroslav

    2017-12-08

    In the study of lime as the basic component of historical mortars and plasters, four lime putties prepared from various kinds of lime of various granulometry and by various ways of preparation were evaluated. The rheological properties and micro-morphologic changes, growing of calcite crystals, and rate of carbonation were monitored. The lime putty prepared from lump lime achieves the best rheological properties, yield stress 214.7 Pa and plastic viscosity 2.6 Pa·s. The suitability of this lime putty was checked by testing the development of calcium hydroxide and calcite crystals using scanning electron microscopy and environmental scanning electron microscopy. The disordered crystals of calcium hydroxide exhibit better carbonation resulting in the large crystals of calcite; therefore, the mortar prepared from the lump lime has the highest flexural strength and compressive strength 0.8/2.5 MPa, its carbonation is the fastest and exhibits the longest durability. Also, thanks to the micro-morphological characterization of samples in their native state by means of environmental scanning electron microscopy, the new way of lime putty preparation by mixing was proven. The preparation consists in the mechanical crash of the lime particles immediately after hydration. This enables the properties of putty prepared from lump lime to be nearly reached.

  15. Static softening following multistage hot deformation of 7150 aluminum alloy: Experiment and modeling

    International Nuclear Information System (INIS)

    Jiang, Fulin; Zurob, Hatem S.; Purdy, Gary R.; Zhang, Hui

    2015-01-01

    Previous studies have demonstrated that the static softening kinetics of 7150 aluminum alloy showed typical sigmoidal behavior at 400 °C and softening plateaus at 300 °C (F.L. Jiang, et al., Mater. Sci. Eng. A, vol. 552, 2012, pp. 269–275). In present work, the static softening mechanisms, the microstructural evolution during post-deformation holding was studied by optical microscopy, scanning electron microscope, electron back-scattered diffraction and transmission electron microscopy. It was demonstrated that recrystallization is essentially absent during post-deformation holding, and that static recovery was the main contribution to static softening. Strain induced precipitation and coarsening caused softening plateaus at 300 °C. In order to better understand the static softening mechanism, physically-based modeling, which integrated recovery and multicomponent particle coarsening modeling, was employed to rationalize the experimental results.

  16. Assessing the effects of soil liming with dolomitic limestone and sugar foam on soil acidity, leaf nutrient contents, grape yield and must quality in a Mediterranean vineyard

    Energy Technology Data Exchange (ETDEWEB)

    Olego, M.A.; Visconti, F.; Quiroga, M.J.; Paz, J.M. De; Garzón-Jimeno, E.

    2016-11-01

    Aluminium toxicity has been recognized as one of the most common causes of reduced grape yields in vineyard acid soils. The main aim of this study was to evaluate the effect of two liming materials, i.e. dolomitic lime and sugar foam, on a vineyard cultivated in an acid soil. The effects were studied in two soil layers (0-30 and 30-60 cm), as well as on leaf nutrient contents, must quality properties and grape yield, in an agricultural soil dedicated to Vitis vinifera L. cv. ‘Mencía’ cultivation. Data management and analysis were performed using analysis of variance (ANOVA). As liming material, sugar foam was more efficient than dolomitic limestone because sugar foam promoted the highest decrease in soil acidity properties at the same calcium carbonate equivalent dose. However, potassium contents in vines organs, including leaves and berries, seemed to decrease as a consequence of liming, with a concomitant increase in must total acidity. Soil available phosphorus also decreased as a consequence of liming, especially with sugar foam, though no effects were observed in plants. For these reasons fertilization of this soil with K and P is recommended along with liming. Grape yields in limed soils increased, although non-significantly, by 30%. This research has therefore provided an important opportunity to advance in our understanding of the effects of liming on grape quality and production in acid soils. (Author)

  17. An Aerobic Digestion of Lime Sludge.

    Science.gov (United States)

    1982-07-01

    removal. 1,2 After lime addition, phosphorus is considered to be in the form of calcium hydroxyapatite (Ca5-(OH)(P04 )3 ), which will not resolubilize...U: c a e - ~ -’ tr *cr. V. (r. C . -~~~ C c C C&c cj Ir u -. C Fy. - U C C - C F.~-cc 0.c gC - - gg MFC - - C -66 TABLE 20. SUMMARY OF LEAST

  18. Imperial Limes - Projections in Medieval Imperial Idea

    Directory of Open Access Journals (Sweden)

    Z.Z. Zhekov

    2015-08-01

    Full Text Available Roman imperial limes from I - V BC was the first state border in world history, which in some sense corresponds to the modern concept of political boundary. It represents sustainable political, military and economic barrier between the Romans and the rest of the world. With minor modifications it retains their basic strategic concept during the period as expressed from the emperors Augustus and Tiberius. Limes become powerful barrier that separates cultural Roman Hellenistic world of the wild barbarian but at the same time limits the constructed infrastructure of roads, forts and towns became a natural cultural, commercial and political mediator between these two initially hostile worlds. In border towns developed a lively trade between Romans and barbarians. Roman traders penetrate inside the barbarian lands getting to know their culture and history. Studying foreign peoples and countries they convey information gathered imperial legate of the Roman population. The same process was developed and of course in the opposite direction. Exchange of information on the other promotes mutual understanding and open living on both sides of the Roman Limes.

  19. Application of lime (CaCO3) to promote forest recovery from severe acidification increases potential for earthworm invasion

    Science.gov (United States)

    Homan, Caitlin; Beirer, Colin M; McCay, Timothy S; Lawrence, Gregory B.

    2016-01-01

    The application of lime (calcium carbonate) may be a cost-effective strategy to promote forest ecosystem recovery from acid impairment, under contemporary low levels of acidic deposition. However, liming acidified soils may create more suitable habitat for invasive earthworms that cause significant damage to forest floor communities and may disrupt ecosystem processes. We investigated the potential effects of liming in acidified soils where earthworms are rare in conjunction with a whole-ecosystem liming experiment in the chronically acidified forests of the western Adirondacks (USA). Using a microcosm experiment that replicated the whole-ecosystem treatment, we evaluated effects of soil liming on Lumbricus terrestris survivorship and biomass growth. We found that a moderate lime application (raising pH from 3.1 to 3.7) dramatically increased survival and biomass of L. terrestris, likely via increases in soil pH and associated reductions in inorganic aluminum, a known toxin. Very few L. terrestris individuals survived in unlimed soils, whereas earthworms in limed soils survived, grew, and rapidly consumed leaf litter. We supplemented this experiment with field surveys of extant earthworm communities along a gradient of soil pH in Adirondack hardwood forests, ranging from severely acidified (pH 5). In the field, no earthworms were observed where soil pH 4.4 and human dispersal vectors, including proximity to roads and public fishing access, were most prevalent. Overall our results suggest that moderate lime additions can be sufficient to increase earthworm invasion risk where dispersal vectors are present.

  20. Effect of lime addition during sewage sludge treatment on characteristics of resulting SSA when it is used in cementitious materials.

    Science.gov (United States)

    Vouk, D; Nakic, D; Štirmer, N; Baricevic, A

    2017-02-01

    Final disposal of sewage sludge is important not only in terms of satisfying the regulations, but the aspect of choosing the optimal wastewater treatment technology, including the sludge treatment. In most EU countries, significant amounts of stabilized and dewatered sludge are incinerated, and sewage sludge ash (SSA) is generated as a by product. At the same time, lime is one of the commonly used additives in the sewage sludge treatment primarily to stabilize the sludge. In doing so, the question arose how desirable is such addition of lime if the sludge is subsequently incinerated, and the generated ash is further used in the production of cementitious materials. A series of mortars were prepared where 10-20% of the cement fraction was replaced by SSA. Since all three types of analyzed SSA (without lime, with lime added during sludge stabilization and with extra lime added during sludge incineration) yielded nearly same results, it can be concluded that if sludge incineration is accepted solution, lime addition during sludge treatment is unnecessary even from the standpoint of preserving the pozzolanic properties of the resulting SSA. Results of the research carried out on cement mortars point to the great possibilities of using SSA in concrete industry.

  1. Characteristic Asphalt Concrete Wearing Course (ACWC) Using Variation Lime Filler

    Science.gov (United States)

    Permana, R. A.; Pramesti, F. P.; Setyawan, A.

    2018-03-01

    This research use of lime filler Sukaraja expected add durability layers of concrete pavement is asphalt damage caused by the weather and load traffic. This study attempts to know how much value characteristic Marshall on a mixture of concrete asphalt using lime filler. This research uses experimental methods that is with a pilot to get results, thus will look filler utilization lime on construction concrete asphalt variation in filler levels 2 %, 3 %, 4 %.The results showed that the use of lime filler will affect characteristic a mixture of concrete asphalt. The more filler chalk used to increase the value of stability. On the cretaceous filler 2 % value of stability is 1067,04 kg. When lime filler levels added to the levels of filler 4 %, the value of stability increased to 1213,92 kg. The flexibility increased the number of filler as levels lime 2 % to 4 % suggests that are conducted more stiff mix.

  2. Effects of corn cob ash on lime stabilized lateritic soil

    Science.gov (United States)

    Nnochiri, Emeka Segun

    2018-03-01

    This study assesses the effects of Corn Cob Ash (CCA) on lime-stabilized lateritic soil. Preliminary tests were carried out on the natural soil sample for purpose of identification and classification. Lime being the main stabilizing material was thoroughly mixed with the soil sample to determine the optimum lime requirement of the sample as a basis for evaluating the effects of the CCA. The optimum lime requirement was 10%. The CCA was thereafter added to the lime stabilized soil in varying proportions of 2, 4, 6, 8 and 10%. Unsoaked CBR increased from 83% at 0% CCA to highest value of 94% at 4% CCA. Unconfined Compressive Strength (UCS) values increased from 1123kN/m2 at 0% CCA to highest value of 1180kN/m2 at 4% CCA. It was therefore concluded that CCA can serve as a good complement for lime stabilization in lateritic soil.

  3. Liming as a method to remedy lakes contaminated by radiostrontium

    International Nuclear Information System (INIS)

    Haakanson, Lars

    2003-01-01

    This work has identified the characteristics regulating lake sensitivity to 90 Sr-contamination and why certain lakes are likely to respond positively to lake liming (Ca-treatment) and when this would not be a feasible or economic remedial measure to lower 90 Sr-levels in fish. The results demonstrate that liming would work best in (1) small, (2) low-productive, (3) oligohumic, (4) acid lakes with (5) low initial Ca-concentrations. It is important to start the liming as soon as possible after the fallout. The liming model discussed in this work can be used to calculate the changes in lake Ca-concentrations and the duration of the liming. The Sr-model can be used to calculate changes in Sr-levels in water, sediments and fish. At best, these simulations indicate that it is realistic to expect that lake liming can reduce peak levels of 90 Sr in fish by 25-40%

  4. Use of demolition residues construction in soil-lime bricks

    International Nuclear Information System (INIS)

    Figueiredo, S.S.; Silva, C.G.; Silva, I.A.; Neves, G.A.

    2011-01-01

    Besides being responsible for several environmental damage caused by its residues, the construction industry is also considered the greatest natural resources consumer. When finely ground, such residues can exhibit cementing properties, which may replace part of the lime used in the manufacture of soil-lime bricks. This study aimed to verify the viability of using demolition residues (DR) in soil-lime bricks without structural function. For this, test specimens were prepared using mixes in a 1:10 ratio of lime:soil and embedding residue in partial replacement of lime in the proportions of 25%, 50% and 75%. The test specimens were submitted to curing periods of 28 and 52 days, then it was determined the compression strength. The results showed that when embedded on moderate percentages, demolition residues construction can be used in the production of soil-lime bricks. (author)

  5. Energy efficiency opportunity guide in the lime industry

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The lime industry processes limestone, an abundant inorganic mineral, for metallurgical, industrial and chemical, environmental, and construction applications. The energy the industry uses results in greenhouse gas emissions and the Canadian Lime Institute, in collaboration with Natural Resources Canada, sponsored the development of this guidebook which is intended to provide ideas for saving energy in the lime industry. This document is a practical source of information and can be used to develop self-audit and evaluation techniques to monitor energy usage. The report first provides an overview of the lime industry, then presents its energy costs. General energy efficiency methodologies are highlighted and, in conclusion, advice on improving energy efficiency in general and specifically for lime industry operations is given. This guidebook provides useful information for lime industry operators who are trying to improve the energy efficiency of their operations.

  6. Evaluation of lime and hydrothermal pretreatments for efficient enzymatic hydrolysis of raw sugarcane bagasse.

    Science.gov (United States)

    Grimaldi, Maira Prearo; Marques, Marina Paganini; Laluce, Cecília; Cilli, Eduardo Maffud; Sponchiado, Sandra Regina Pombeiro

    2015-01-01

    Ethanol production from sugarcane bagasse requires a pretreatment step to disrupt the cellulose-hemicellulose-lignin complex and to increase biomass digestibility, thus allowing the obtaining of high yields of fermentable sugars for the subsequent fermentation. Hydrothermal and lime pretreatments have emerged as effective methods in preparing the lignocellulosic biomass for bioconversion. These pretreatments are advantageous because they can be performed under mild temperature and pressure conditions, resulting in less sugar degradation compared with other pretreatments, and also are cost-effective and environmentally sustainable. In this study, we evaluated the effect of these pretreatments on the efficiency of enzymatic hydrolysis of raw sugarcane bagasse obtained directly from mill without prior screening. In addition, we evaluated the structure and composition modifications of this bagasse after lime and hydrothermal pretreatments. The highest cellulose hydrolysis rate (70 % digestion) was obtained for raw sugarcane bagasse pretreated with lime [0.1 g Ca(OH)2/g raw] for 60 min at 120 °C compared with hydrothermally pretreated bagasse (21 % digestion) under the same time and temperature conditions. Chemical composition analyses showed that the lime pretreatment of bagasse promoted high solubilization of lignin (30 %) and hemicellulose (5 %) accompanied by a cellulose accumulation (11 %). Analysis of pretreated bagasse structure revealed that lime pretreatment caused considerable damage to the bagasse fibers, including rupture of the cell wall, exposing the cellulose-rich areas to enzymatic action. We showed that lime pretreatment is effective in improving enzymatic digestibility of raw sugarcane bagasse, even at low lime loading and over a short pretreatment period. It was also demonstrated that this pretreatment caused alterations in the structure and composition of raw bagasse, which had a pronounced effect on the enzymes accessibility to the

  7. Direct Cytoskeleton Forces Cause Membrane Softening in Red Blood Cells

    Science.gov (United States)

    Rodríguez-García, Ruddi; López-Montero, Iván; Mell, Michael; Egea, Gustavo; Gov, Nir S.; Monroy, Francisco

    2015-01-01

    Erythrocytes are flexible cells specialized in the systemic transport of oxygen in vertebrates. This physiological function is connected to their outstanding ability to deform in passing through narrow capillaries. In recent years, there has been an influx of experimental evidence of enhanced cell-shape fluctuations related to metabolically driven activity of the erythroid membrane skeleton. However, no direct observation of the active cytoskeleton forces has yet been reported to our knowledge. Here, we show experimental evidence of the presence of temporally correlated forces superposed over the thermal fluctuations of the erythrocyte membrane. These forces are ATP-dependent and drive enhanced flickering motions in human erythrocytes. Theoretical analyses provide support for a direct force exerted on the membrane by the cytoskeleton nodes as pulses of well-defined average duration. In addition, such metabolically regulated active forces cause global membrane softening, a mechanical attribute related to the functional erythroid deformability. PMID:26083919

  8. Removal of phosphate from greenhouse wastewater using hydrated lime.

    Science.gov (United States)

    Dunets, C Siobhan; Zheng, Youbin

    2014-01-01

    Phosphate (P) contamination in nutrient-laden wastewater is currently a major topic of discussion in the North American greenhouse industry. Precipitation of P as calcium phosphate minerals using hydrated lime could provide a simple, inexpensive method for retrieval. A combination of batch experiments and chemical equilibrium modelling was used to confirm the viability of this P removal method and determine lime addition rates and pH requirements for greenhouse wastewater of varying nutrient compositions. Lime: P ratio (molar ratio of CaMg(OH)₄: PO₄‒P) provided a consistent parameter for estimating lime addition requirements regardless of initial P concentration, with a ratio of 1.5 providing around 99% removal of dissolved P. Optimal P removal occurred when lime addition increased the pH from 8.6 to 9.0, suggesting that pH monitoring during the P removal process could provide a simple method for ensuring consistent adherence to P removal standards. A Visual MINTEQ model, validated using experimental data, provided a means of predicting lime addition and pH requirements as influenced by changes in other parameters of the lime-wastewater system (e.g. calcium concentration, temperature, and initial wastewater pH). Hydrated lime addition did not contribute to the removal of macronutrient elements such as nitrate and ammonium, but did decrease the concentration of some micronutrients. This study provides basic guidance for greenhouse operators to use hydrated lime for phosphate removal from greenhouse wastewater.

  9. Time evolution of pore system in lime - Pozzolana composites

    Science.gov (United States)

    Doleželová, Magdaléna; Čáchová, Monika; Scheinherrová, Lenka; Keppert, Martin

    2017-11-01

    The lime - pozzolana mortars and plasters are used in restoration works on building cultural heritage but these materials are also following the trend of energy - efficient solutions in civil engineering. Porosity and pore size distribution is one of crucial parameters influencing engineering properties of porous materials. The pore size distribution of lime based system is changing in time due to chemical processes occurring in the material. The present paper describes time evolution of pore system in lime - pozzolana composites; the obtained results are useful in prediction of performance of lime - pozzolana systems in building structures.

  10. Increased sustainability of softening by producing pure calcite pellets for reuse

    NARCIS (Netherlands)

    Hofs, B; Baars, ET; Palmen, LJ; Elings, JA; Kors, L.J.; Kramer, O.J.I.; Koppers, H; van der Hoek, J.P.

    2015-01-01

    About 50% of the drinking water in the Netherlands is centrally softened by the drinking water companies in a process known as pellet softening. In this process a base and seeding material are mixed in an upflow reactor, where subsequently CaCO3 precipitates on a seed core as pellets. The seeding

  11. Life cycle assessment of central softening of very hard drinking water

    DEFF Research Database (Denmark)

    Godskesen, Berit; Hauschild, Michael Zwicky; Rygaard, Martin

    2012-01-01

    Life Cycle Assessment (LCA) to quantify the environmental impacts of central softening of drinking water considering both the negative effects at the waterworks and the positive effects imposed by the changed water quality in the households. The LCA modeling considered central softening of drinking......Many consumers prefer softened water due to convenience issues such as avoidance of removing limescale deposits from household appliances and surfaces, and to reduce consumption of cleaning agents and laundry detergents leading to lower household expenses. Even though central softening of drinking...... water entailed an increased use of energy, sand and chemicals at the waterworks, the distributed and softened drinking water supported a decrease in consumption of energy and chemical agents in the households along with a prolonged service life of household appliances which heat water. This study used...

  12. LIMES Large Infrastructure in Mathematics - Enhanced Services

    CERN Document Server

    Fachinformationszentrum Energie, Physik, Mathematik. Karlsruhe

    The Large Infrastructure in Mathematics - Enhanced Services (LIMES) Project is a RTD project within the Fifth (EC) Framework Programme - Horizontal Programme "Improving human research potential and the socio-economic knowledge base", Access to Resear The objective of this project is to upgrade the existing database Zentralblatt-MATH into a European based world class database for mathematics (pure and applied) by a process of technical improvement and wide Europeanisation, improving the present distribuited system. The goal is to make Zentralblatt MATH a world reference database, offering full coverage of the mathematics literature worldwide ncluding bibliographic data, peer reviews and/or abstracts, indexing, classification and search,

  13. Pit lake lime dosing: Assessment of the performance of the treatment based on a high-spatial resolution AUV survey

    Science.gov (United States)

    Delgado, Jordi; García-Morrondo, David; Cereijo-Arango, José Luis; Muñoz-Ibáñez, Andrea; Grande-García, Elisa; Rodríguez-Cedrún, Borja; Juncosa-Rivera, Ricardo

    2016-04-01

    The acidity of mine waters is typically corrected with passive (where possible) and/or active (i.e. chemical additions) systems. In the case of active treatments, lime dosing is a widespread technique due to the relatively ease of implementation and reduced operational costs. While neutralization of acidic waters is routinely performed in circulating water treatment facilities this is not so simple in open waters (e.g. pit lakes) because an efficient treatment requires the adequate distribution of the alkaline reagents throughout the volume of interest. To cope with this problem, a number of technical approaches have been proposed including active stirring (bubbling, etc.), surface spread diffusion, etc. In the early times of flooding of the Meirama mine, managers considered the necessity of lime dosing to correct the initially acidic mine waters. However, lake evolution proved that liming was not necessary and it was desirable to allow a reasonably unmanned evolution of the reclaimed system. In order to ensure that the lime dosing system is in good operative conditions in case of necessity, according to a prescribed time schedule to time mine managers put it in operation. That give us the opportunity to perform a large-scale "tracer" experiment useful to test the efficiency of wet lime dosing in a large water body. Dry lime, which is kept in a storage silo, is directly dosed over the channel of a small stream discharging in the lake. Therefore, stream water becomes saturated with lime and a pH of approximately 12.3. Stream water flows in cascade to the lake so that a certain potential and kinetic energy transfer is delivered to the lake. That promotes currents that enhance the re-distribution of the alkalinity load. In order to check for the distribution of alkaline water in the top body of the lake, an autonomous underwater vehicle (Yellow Spring Instruments Inc. EcoMapper AUV) was used. This device allows for the high- frequency simultaneous measurement of a

  14. Application of Lime Additive on Cementation of Concentrated Low Activities Liquid Radwaste Containing Boric Acid

    International Nuclear Information System (INIS)

    Bahdir-Johan

    2000-01-01

    The effect of lime additive on the waste form containing boric acid and the activity 1 μCi/ml have been studied. The studying parameter was the optimum lime additive in concentrate. The sample was made by cement slurry containing boric acid. The cement slurry composition are water/cement ratio (W/C) was 0.35, sand/cement ratio (S/C) was 0.75 and boric (B) was 15000 ppm. On this condition into cement slurry was added the lime additive (K/C) 0.05 -0.8 by weigh. The quality test included density, compressive strength and leaching rate. The density was determination by weighing and measuring sample volume, compressive strength determination using Paul Weber apparatus and leaching rate tested using aquadest. The result of this research are the lime/cement ratio (K/C) 0.30; the density (ρ) 2.449 ± 0.008 g.cm -3 , the compressive strength (Γ) 44.005 ± 0.012 N.mm -2 and the leaching rate (Rn) 7.20x10 -4 -0.90x10 -4 g.cm -2 day -1 . According to this research the quality of the waste form has been complied the IAEA quality standard. (author)

  15. Employing natural reagents from turmeric and lime for acetic acid determination in vinegar sample

    Directory of Open Access Journals (Sweden)

    Sam-ang Supharoek

    2018-04-01

    Full Text Available A simple, rapid and environmentally friendly sequential injection analysis system employing natural extract reagents was developed for the determination of acetic acid following an acid–base reaction in the presence of an indicator. Powdered lime and turmeric were utilized as the natural base and indicator, respectively. Mixing lime and turmeric produced an orange to reddish-brown color solution which absorbed the maximum wavelength at 455 nm, with absorbance decreasing with increasing acetic acid concentration. Influential parameters including lime and turmeric concentrations, reagent and sample aspirated volumes, mixing coil length and dispensing flow rate were investigated and optimized. A standard calibration graph was plotted for 0–5.0 mmol/L acetic acid with r2 = 0.9925. Relative standard deviations (RSD at 2.0 and 4.0 mmol/L acetic acid were less than 3% (n = 7, with limit of detection (LOD and limit of quantification (LOQ at 0.12 and 0.24 mmol/L, respectively. The method was successfully applied to assay acetic acid concentration in cooking vinegar samples. Results achieved were not significantly different from those obtained following a batchwise standard AOAC titration method. Keywords: Acetic acid assay, Natural reagent, Turmeric, Lime, Sequential injection analysis

  16. Incorporation of turmeric-lime mixture during the preparation of ...

    African Journals Online (AJOL)

    GREGO

    2007-03-19

    Mar 19, 2007 ... behaviour) of 2 min-blanched samples (both treated and control) were the maximum among other corresponding puree samples. Thus, 2 min blanching time may be preferred for the preparation of this new type of turmeric-lime treated tomato puree product. Key words: Turmeric-lime, Lycopersicon ...

  17. Carbonation of lime and cement stabilized layers in road construction

    CSIR Research Space (South Africa)

    Netterberg, F

    1984-04-01

    Full Text Available The problem of deterioration of lime, lime-slag and cement stabilized pavement layers during curing, before sealing and in service is partly ascribed to carbonation of the stabilizer during curing and subsequent exposure to the atmosphere before...

  18. Investigation of Copper Sorption by Sugar Beet Processing Lime Waste

    Science.gov (United States)

    In the western United States, sugar beet processing for sugar recovery generates a lime-based waste product (~250,000 Mg yr-1) that has little liming value in the region’s calcareous soils. This area has recently experienced an increase in dairy production, with dairi...

  19. 76 FR 82295 - Central Power & Lime LLC; Notice of Filing

    Science.gov (United States)

    2011-12-30

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket Nos. EL12-18-000; QF82-207-007] Central Power & Lime LLC; Notice of Filing December 23, 2011. Take notice that on December 22, 2011, Central Power & Lime LLC, pursuant to sections 18 CFR 292.205(c) and 385.207 of the Federal Energy...

  20. Efficacy and phytotoicity of lime sulphur in organic apple production

    NARCIS (Netherlands)

    Holb, I.J.; Jong, de P.F.; Heijne, B.

    2003-01-01

    Curative and preventive efficacy and phytotoxicity of lime sulphur spray schedules, based on a warning system, were evaluated in the Netherlands during two growing seasons under field conditions. In most cases, lime sulphur treatments applied either curatively or preventively resulted in

  1. Stabilization of expansive soil using bagasse ash & lime | Wubshet ...

    African Journals Online (AJOL)

    7-5 soil on the AASHTO classification was stabilized using 3% lime, 15% bagasse ash and 15% bagasse ash in combination with 3% lime by dry weight of the soil. The effect of the additives on the soil was investigated with respect to plastcity, ...

  2. A nano approach to consolidation of degraded historic lime mortars

    Czech Academy of Sciences Publication Activity Database

    Drdácký, Miloš; Slížková, Zuzana; Ziegenbalg, G.

    2009-01-01

    Roč. 8, č. 2 (2009), s. 13-22 ISSN 1662-5250 R&D Projects: GA ČR(CZ) GA103/06/1609 Institutional research plan: CEZ:AV0Z20710524 Keywords : lime water * calcium hydroxide nanosuspension * lime mortar Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 0.571, year: 2009

  3. Liming of acid tropical soils: practice, prospects and constraints ...

    African Journals Online (AJOL)

    But the incidental inclusion of liming materials in fertilizers has not been effective and sustainable due to the intensive land use activities, constant application of acid-forming chemical fertilizers, leaching losses of bases and crop removal. Liming materials themselves vary in their calcium and magnesium contents and ...

  4. Engineering Properties of Bentonite Stabilized with Lime and Phosphogypsum

    Directory of Open Access Journals (Sweden)

    Kumar Sujeet

    2014-12-01

    Full Text Available Engineering properties such as compaction, unconfined compressive strength, consistency limits, percentage swell, free swell index, the California bearing ratio and the consolidation of bentonite stabilized with lime and phosphogypsum are presented in this paper. The content of the lime and phosphogypsum varied from 0 to 10 %. The results reveal that the dry unit weight and optimum moisture content of bentonite + 8 % lime increased with the addition of 8 % phosphogypsum. The percentage of swell increased and the free swell index decreased with the addition of 8 % phosphogypsum to the bentonite + 8 % lime mix. The unconfined compressive strength of the bentonite + 8 % lime increased with the addition of 8 % phosphogypsum as well as an increase in the curing period up to 14 days. The liquid limit and plastic limit of the bentonite + 8 % lime increased, whereas the plasticity index remained constant with the addition of 8 % phosphogypsum. The California bearing ratio, modulus of subgrade reaction, and secant modulus increased for the bentonite stabilized with lime and phosphogypsum. The coefficient of the consolidation of the bentonite increased with the addition of 8 % lime and no change with the addition of 8 % phosphogypsum.

  5. Some studies on the reaction between fly ash and lime

    Indian Academy of Sciences (India)

    Unknown

    Blain's air permeability apparatus was used for ... Pulverized lime with high per- centage of CaO (> 80 ... kept in a low-pressure autoclave at an average steam pressure and ... ing the solubility of lime in a solvent containing 1 part by volume of ...

  6. Energy saving plan for lime calcining kiln

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Lime calcining kilns operating in China are of old type, consuming more heat energy by 30% or more than the latest type kilns. For the purpose of the COP3 joint implementation, a renewal plan was discussed taking up Benxi Steel Group Company as the object. The new type kiln is a parallel flow energy regenerating (Maerz) kiln. It has as high thermal efficiency as 900 kcal/kg of product. Annual fuel conservation as converted into crude oil will be 7.49x10{sup 3} tons, annual fuel cost reduction will be 101,200,000 yuan, and annual reduction in CO2 emission will be 23,200 tons. The estimated cost required for the project will be 991 million yen, or 66,070,000 yuan if the exchange rate is assumed to be 15 yen to one yuan. The profitability was discussed based on using bank loans and the special environmental yen loan. The investment recovering period was calculated as 7.9 years. This provides no realizability as a project on the business base. However, China strongly desires renewal of the facilities because of discharge of dust from old type facilities, and inferior quality of lime products. The project could be a candidate without doubt if the CDM system will have been established. (NEDO)

  7. Root distribution of rootstocks for 'Tahiti' lime

    Directory of Open Access Journals (Sweden)

    Neves Carmen Silvia Vieira Janeiro

    2004-01-01

    Full Text Available Field studies on citrus roots are important for genetic selection of cultivars and for management practices such as localized irrigation and fertilization. To characterize root systems of six rootstocks, taking into consideration chemical and physical characteristics of a clayey Typic Hapludox of the Northern State of Paraná, this study was performed having as scion the 'IAC-5 Tahiti' lime [Citrus latifolia (Yu. Tanaka]. The rootstocks 'Rangpur' lime (C. limonia Osbeck, 'Africa Rough' lemon (C. jambhiri Lush., 'Sunki' mandarin [C. sunki (Hayata hort. ex Tan.], Poncirus trifoliata (L. Raf., 'C13' citrange [C. sinensis (L. Osb. x P. trifoliata (L. Raf] and 'Catânia 2' Volkamer lemon (C. volkameriana Ten. & Pasq. were used applying the trench profile method and the SIARCS® 3.0 software to determine root distribution. 'C-13' citrange had the largest root system. 'Volkamer' lemon and 'Africa Rough' lemon presented the smallest amount of roots. The effective depth for 80 % of roots was 31-53 cm in rows and 67-68 cm in inter-rows. The effective distance of 80 % of roots measured from the tree trunk exceeded the tree canopy for P. trifoliata, 'Sunki' mandarin, and 'Volkamer' and 'Africa Rough' lemons.

  8. Wetland vegetation responses to liming an Adirondack watershed

    Energy Technology Data Exchange (ETDEWEB)

    Mackun, I.R.

    1993-01-01

    Watershed liming as a long-term mitigation strategy to neutralize lake acidity, from increasing acid deposition, was initiated in North America at Woods Lake in the west central Adirondack region of New York. In October 1989, a dose of 10 MT lime (83.5% CaCO[sub 3]) ha[sup [minus]1] was aerially applied to 48% of the watershed. The wetlands adjacent to Woods Lake showed two distinct community types: one dominated by Chamaedaphne calyculata, and one dominated by graminoids and other herbaceous species. Within two years, liming did not alter the structure of either community type, and changed the cover or frequency of only 6 of 64 individual taxa. Most of these changes occurred in the herbaceous community type. The only strong positive response to liming was a nearly threefold increase in cover of the rhizomatous sedge Cladium mariscoides. The cover of Carex interior and Sphagnum spp. benefited from lime addition, while cover of Drosera intermedia and Muhlenbergia uniflora, and frequency of Hypericum canadense responded negatively to lime. Liming influenced the competitive release of only three taxa, all forbs with small growth forms. The tissue chemistry of foliage and twigs of Myrica gale, Chamaedaphne calyculata, and Carex stricta in the Chamaedaphne calyculata community type clearly illustrated species-specific patterns of nutrient accumulation and allocation both before and after liming. Concentrations of 17 of 20 elements responded to liming, although the responses varied among species and plant parts. Carex foliage was least responsive to liming, and Chamaedaphne twigs were most responsive. Elemental changes in plant tissues will be reflected in litter and many influence long-term nutrient dynamics in the wetland community.

  9. Effect of lime and wood ash on the nixtamalization of maize and tortilla chemical and nutritional characteristics.

    Science.gov (United States)

    Pappa, María Renée; de Palomo, Patricia Palacios; Bressani, Ricardo

    2010-06-01

    The objective of the study was to obtain information on the chemical composition, functional properties, sensory quality and protein value of tortillas made from the nixtamalization of maize using either lime or wood ashes. The Ca, K, Mg, Fe, and Zn content of lime and wood ashes showed lime to be high in Ca content while wood ash contained more K and about 71% of the Ca content of lime. Both contained relatively high levels of Mg, Fe and Zn, but more so in the wood ashes. The level of reagent for nixtamalization was set at 0.8% of the maize weight. All other processing conditions were kept constant. The pH of the cooking solution was 12.0 for lime and 10.9 for wood ash. The moisture content of maize at 60 min of cooking was 45.8% for both treatments, however after 12 h of soaking, moisture level was 51.0% for the lime treatment and only 46.8% for the ash treatment. Solids (2.4%) in the lime cooking liquor were higher than in the wood ash liquor (1.0%). Chemical composition changes were similar between treatments in masa and tortilla; however, both masa and tortillas absorbed relatively high levels of all minerals including Fe and Zn from the wood ash treatment. The different treatment influenced functional properties particularly hardness and color. Tortilla characteristics were also similar. Protein quality of both alkali cooked products was lower than that of raw corn, more so the product from the wood ash treatment. Although some differences were observed in the sensory studies, human subjects did not dislike the wood ash made tortillas.

  10. In-Depth Transcriptome Sequencing of Mexican Lime Trees Infected with Candidatus Phytoplasma aurantifolia.

    Science.gov (United States)

    Mardi, Mohsen; Karimi Farsad, Laleh; Gharechahi, Javad; Salekdeh, Ghasem Hosseini

    2015-01-01

    Witches' broom disease of acid lime greatly affects the production of Mexican lime in Iran. It is caused by a phytoplasma (Candidatus Phytoplasma aurantifolia). However, the molecular mechanisms that underlie phytoplasma pathogenicity and the mode of interactions with host plants are largely unknown. Here, high-throughput transcriptome sequencing was conducted to explore gene expression signatures associated with phytoplasma infection in Mexican lime trees. We assembled 78,185 unique transcript sequences (unigenes) with an average length of 530 nt. Of these, 41,805 (53.4%) were annotated against the NCBI non-redundant (nr) protein database using a BLASTx search (e-value ≤ 1e-5). When the abundances of unigenes in healthy and infected plants were compared, 2,805 transcripts showed significant differences (false discovery rate ≤ 0.001 and log2 ratio ≥ 1.5). These differentially expressed genes (DEGs) were significantly enriched in 43 KEGG metabolic and regulatory pathways. The up-regulated DEGs were mainly categorized into pathways with possible implication in plant-pathogen interaction, including cell wall biogenesis and degradation, sucrose metabolism, secondary metabolism, hormone biosynthesis and signalling, amino acid and lipid metabolism, while down-regulated DEGs were predominantly enriched in ubiquitin proteolysis and oxidative phosphorylation pathways. Our analysis provides novel insight into the molecular pathways that are deregulated during the host-pathogen interaction in Mexican lime trees infected by phytoplasma. The findings can be valuable for unravelling the molecular mechanisms of plant-phytoplasma interactions and can pave the way for engineering lime trees with resistance to witches' broom disease.

  11. Restoration of high zinc and lead tailings with municipal biosolids and lime: a field study.

    Science.gov (United States)

    Brown, Sally; Svendsen, Alex; Henry, Chuck

    2009-01-01

    A field study was conducted to test the ability of biosolids (BS) and different types of lime to increase soil pH, neutralize subsoil acidity, and restore a vegetative cover to alluvial mine tailings in Leadville, CO. The tailings had soil pH of 5.2 and total Cd, Pb, and Zn of 75+/-20, 2600+/-1100, and 6700+/-1900 mg kg(-1). Types of lime included agricultural lime (AL), sugar beet lime (SBL), and lime kiln dust (LKD) applied at 224 Mg ha(-1) calcium carbonate equivalent. Plots were established in 2000 and monitored intermittently through 2007. All amendments increased pH in surface and subsurface depths, with LKD, LKD+BS, and SBL+BS being the most effective. Amendments also reduced 0.01 mol L(-1) Ca(NO3)2 extractable Zn and Cd compared to the control. Plant growth was sparse on all treatments with limited yield for three of four harvests. Poor growth may have been related to elevated electrical conductivity (EC). All amendments except LKD alone (5.79 dS m(-1)) increased EC compared to the control treatment (5.28 dS m(-1)). Electrical conductivity was highest in 2002 which had the lowest summer rainfall. In 2005 EC in all treatments except the SBL+BS was similar in the surface soil. Aboveground plant tissue concentrations of Zn and Cd were also elevated. Limited precipitation and high electrical conductivity may be responsible for poor plant growth. Higher rainfall for the last sampling period resulted in significant growth in the LKD+BS, SBL+BS, and LKD alone treatments.

  12. Hardening and softening analysis of pure titanium based on the dislocation density during torsion deformation

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Han; Li, Fuguo, E-mail: fuguolx@nwpu.edu.cn; Li, Jinghui; Ma, Xinkai; Li, Jiang; Wan, Qiong

    2016-08-01

    The hardening and softening phenomena during torsion deformation are studied based on the Taylor dislocation model for pure titanium. The hardening and softening phenomena are observed through the hardness analysis during micro-indentation test and micro-hardness test. Besides, the variations of indentation size also verify the existence of hardening and softening phenomena during torsion. The variations of geometric necessary dislocations (GNDs) and statistic store dislocations (SSDs) state that the positions of high dislocation density and low dislocation density correspond to the positions of hardening and softening. The results from the microstructure, grain boundaries evolution and twins analysis indicate the twins play an important role in appearance of hardening and softening phenomena. The appearance of hardening and softening phenomena are attributed to the combination of different slip systems and twinning systems combining with the Schmid Factor (SF) analysis and the transmission electron microscope (TEM). The appearance of hardening and softening phenomena can be explained by the Taylor dislocation theory based on TEM analysis. - Highlights: • The phenomena can be characterized by Taylor dislocation model. • The variation of GNDs leads to the phenomena. • The phenomena are proved by micro-hardness, indentation hardness. • The {10-12} twin and {11-24} twin play an important role in the phenomena.

  13. Life cycle assessment of central softening of very hard drinking water.

    Science.gov (United States)

    Godskesen, B; Hauschild, M; Rygaard, M; Zambrano, K; Albrechtsen, H-J

    2012-08-30

    Many consumers prefer softened water due to convenience issues such as avoidance of removing limescale deposits from household appliances and surfaces, and to reduce consumption of cleaning agents and laundry detergents leading to lower household expenses. Even though central softening of drinking water entailed an increased use of energy, sand and chemicals at the waterworks, the distributed and softened drinking water supported a decrease in consumption of energy and chemical agents in the households along with a prolonged service life of household appliances which heat water. This study used Life Cycle Assessment (LCA) to quantify the environmental impacts of central softening of drinking water considering both the negative effects at the waterworks and the positive effects imposed by the changed water quality in the households. The LCA modeling considered central softening of drinking water from the initial hardness of the region of study (Copenhagen, Denmark) which is 362 mg/L as CaCO(3) to a final hardness as CaCO(3) of 254 (a softening depth of 108) mg/L or 145 (a softening depth of 217) mg/L. Our study showed that the consumer preference can be met together with reducing the impact on the environment and the resource consumption. Environmental impacts decreased by up to 3 mPET (milli Personal Equivalent Targeted) and the break-even point from where central softening becomes environmentally beneficial was reached at a softening depth of only 22 mg/L as CaCO(3). Both energy-related and chemically related environmental impacts were reduced as well as the consumption of resources. Based on scarcity criteria, nickel was identified as the most problematic non-renewable resource in the system, and savings of up to 8 mPR (milli Person Reserve) were found. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Cyclically induced softening due to low-angle boundary annihilation in a martensitic steel

    International Nuclear Information System (INIS)

    Sauzay, Maxime; Brillet, Helene; Monnet, Isabelle; Mottot, Michel; Barcelo, Francoise; Fournier, Benjamin; Pineau, Andre

    2005-01-01

    Martensitic steels are known for their softening during cyclic tests carried out at high temperature. The softening has been at least partially explained by lath and sub-grain boundary elimination. This article is dedicated to an attempt at modelling both phenomena. Thanks to mechanical tests it is shown that the softening is mainly due to a decrease of the backstress. Transmission electron microscopy allows us to propose a mechanism of low-angle boundary elimination. Annihilation between dislocations of low-angle boundaries and incident mobile dislocations is modelled. The macroscopic backstress is finally computed using a Hall-Petch law and the Taylor model

  15. Experimental evidence of zone-center optical phonon softening by accumulating holes in thin Ge

    Directory of Open Access Journals (Sweden)

    Shoichi Kabuyanagi

    2016-01-01

    Full Text Available We discuss the impact of free carriers on the zone-center optical phonon frequency in germanium (Ge. By taking advantage of the Ge-on-insulator structure, we measured the Raman spectroscopy by applying back-gate bias. Phonon softening by accumulating holes in Ge film was clearly observed. This fact strongly suggests that the phonon softening in heavily-doped Ge is mainly attributed to the free carrier effect rather than the dopant atom counterpart. Furthermore, we propose that the free carrier effect on phonon softening is simply understandable from the viewpoint of covalent bonding modification by free carriers.

  16. Nonlinear response to the multiple sine wave excitation of a softening--hardening system

    International Nuclear Information System (INIS)

    Koplik, B.; Subudhi, M.; Curreri, J.

    1979-01-01

    In studying the earthquake response of the HTGR core, it was observed that the system can display softening--hardening characteristics. This is of great consequence in evaluating the structural safety aspects of the core. In order to obtain a better understanding of the governing parameters, an investigation was undertaken with a single-degree-of-freedom system having a softening--hardening spring characteristic and excited by multiple sine waves. A parametric study varying the input amplitudes and the spring characteristic was performed. Transients were introduced into the system, and the jump phenomena between the lower softening characteristics to the higher hardening curve was studied

  17. Analysis of Balanced Double Lap Joints with a Bi-Linear Softening Adhesive

    DEFF Research Database (Denmark)

    Hansen, Christian Skodborg; Stang, Henrik; Schmidt, Jacob Wittrup

    2010-01-01

    of cracked concrete disks strengthened with adhesive bonded fiber reinforced polymers (FRP), or in any other structure comparable to a double lap joint with a softening interface. The present constitutive model can be changed to fit any model with the same shape of constitutive relationship, see Figure 1.......The response of a bonded symmetric balanced double lap joint under tensile loading with a bilinear softening adhesive is described with a closed form solution. Since bonded joints in concrete structures undergo softening, a versatile model to describe the response for a wide range of constitutive...

  18. Liming and postharvest quality of carambola fruits

    Directory of Open Access Journals (Sweden)

    Renato de Mello Prado

    2005-09-01

    Full Text Available To determine the effects of lime application on the postharvest quality of carambola fruit, an experiment with carambola trees cultivated on an acid soil was conducted at the Bebedouro, São Paulo, Brazil. The trees were treated with increasing doses of lime during the pre-planting period. Liming led to a increase in calcium concentration of carambola leaves and fruits. Adequate nutrition of the plant with calcium improved post-harvest fruit quality, permitting a longer (~ 2 days period of storage under ambient conditions.Tendo como objetivo avaliar os efeitos da aplicação de doses crescentes de calcário ao solo, na qualidade de frutos de caramboleira pela avaliação das alterações físico-químicas dos frutos após a colheita, foi instalado um experimento em Bebedouro-SP,Brasil, sobre um Latossolo Vermelho distrófico, ácido. Os tratamentos foram doses crescentes de calcário, em pré-plantio, como segue: D0 = zero; D1 = metade da dose; D2 = a dose; D3 = 1,5 vez a dose; e D4 = 2 vezes a dose para elevar V= 70%. No florescimento da caramboleira, avaliou-se o teor de cálcio na folha. Após a colheita dos frutos, determinou-se o teor de cálcio na polpa, o peso dos frutos, diâmetro transversal, comprimento, peso da polpa, % de polpa, ºBrix, acidez titulável e Ratio dos frutos. Diariamente, durante sete dias de armazenamento em condições ambiente, determinou-se a perda de massa fresca e a firmeza dos frutos. A calagem proporcionou um aumentou linear de cálcio nas folhas e nos frutos da caramboleira. A nutrição adequada da planta com cálcio melhorou a qualidade dos frutos pós-colheita, permitindo um período de armazenamento mais longo (~ 2 days, em condições ambiente.

  19. Study of the creep of lime-stabilised zirconia

    International Nuclear Information System (INIS)

    Saint-Jacques, Robert G.

    1971-09-01

    This research thesis reports the study of creep of stabilised zirconia containing between 13 and 20 per cent of lime, at temperatures between 1.200 and 1.400 C, and under compression stresses between 500 and 4.000 pounds by square inch. Specimens are polycrystalline with an average grain diameter between 7 and 29 microns. The author notably shows that the creep rate of lime-stabilised zirconia is directly proportional to the applied stress, and that the creep apparent activation energy is close to activation energy of volume self-diffusion of calcium and zirconium in lime-stabilised zirconia. Results of creep tests show that, in the studied conditions, the creep rate is directly proportional to the inverse of the grain average diameter, and this is in compliance with the Gifkins and Snowden theory of creep by sliding at grain boundaries. The author also shows that the creep rate of the lime stabilised zirconia varies with lime content, and reaches a maximum when zirconia contains about 15 per cent of lime. Lower creep rates obtained for higher and lower lime contents are explained [fr

  20. Kaffir lime leaves extract inhibits biofilm formation by Streptococcus mutans.

    Science.gov (United States)

    Kooltheat, Nateelak; Kamuthachad, Ludthawun; Anthapanya, Methinee; Samakchan, Natthapon; Sranujit, Rungnapa Pankla; Potup, Pachuen; Ferrante, Antonio; Usuwanthim, Kanchana

    2016-04-01

    Although kaffir lime has been reported to exhibit antioxidant and antileukemic activity, little is known about the antimicrobial effect of kaffir lime extract. Because Streptococcus mutans has been known to cause biofilm formation, it has been considered the most important causative pathogen of dental caries. Thus, the effective control of its effects on the oral biofilm is the key to the prevention of dental caries. The aims of the present study were to investigate the effect of kaffir lime leaves extract on biofilm formation and its antibacterial activity on S. mutans. We examined the effect of kaffir lime leaves extract on growth and biofilm formation of S. mutans. For the investigation we used a kaffir lime extract with high phenolic content. The minimum inhibitory concentration of the extract was determined by broth microdilution assay. The inhibitory effect of the test substances on biofilm formation was also investigated by biofilm formation assay and qRT-PCR of biofilm formation-associated genes. Kaffir lime leaves extract inhibits the growth of S. mutans, corresponding to the activity of an antibiotic, ampicillin. Formation of biofilm by S. mutans was also inhibited by the extract. These results were confirmed by the down-regulation of genes associated with the biofilm formation. The findings highlight the ability of kaffir lime leaves extract to inhibit S. mutans activity, which may be beneficial in the prevention of biofilm formation on dental surface, reducing dental plaque and decreasing the chance of dental carries. Copyright © 2016 Elsevier Inc. All rights reserved.

  1. Effect of lime concentration on gelatinized maize starch dispersions properties.

    Science.gov (United States)

    Lobato-Calleros, C; Hernandez-Jaimes, C; Chavez-Esquivel, G; Meraz, M; Sosa, E; Lara, V H; Alvarez-Ramirez, J; Vernon-Carter, E J

    2015-04-01

    Maize starch was lime-cooked at 92 °C with 0.0-0.40% w/w Ca(OH)2. Optical micrographs showed that lime disrupted the integrity of insoluble remnants (ghosts) and increased the degree of syneresis of the gelatinized starch dispersions (GSD). The particle size distribution was monomodal, shifting to smaller sizes and narrower distributions with increasing lime concentration. X-ray patterns and FTIR spectra showed that crystallinity decreased to a minimum at lime concentration of 0.20% w/w. Lime-treated GSD exhibited thixotropic and viscoelastic behaviour. In the linear viscoelastic region the storage modulus was higher than the loss modulus, but a crossover between these moduli occurred in the non-linear viscoelastic region. The viscoelastic properties decreased with increased lime concentration. The electrochemical properties suggested that the amylopectin-rich remnants and the released amylose contained in the continuous matrix was firstly attacked by calcium ions at low lime levels (<0.20% w/w), disrupting the starch gel microstructure. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Phytochemical fingerprints of lime honey collected in serbia.

    Science.gov (United States)

    Gašić, Uroš; Šikoparija, Branko; Tosti, Tomislav; Trifković, Jelena; Milojković-Opsenica, Dušanka; Natić, Maja; Tešić, Živoslav

    2014-01-01

    Composition of phenolic compounds and the sugar content were determined as the basis for characterization of lime honey from Serbia. Particular attention was given to differences in phytochemical profiles of ripe and unripe lime honey and lime tree nectar. Melissopalynological analysis confirmed domination of Tilia nectar in all analyzed samples. Phenolic acids, abscisic acid, flavonoids, and flavonoid glycosides were determined by means of ultra-HPLC coupled with a hybrid mass spectrometer (UHPLC-OrbiTrap). Sugar content was determined using high-performance anion-exchange chromatography with amperometric detection. Similar phenolic compounds characterized unripe and ripe honeys, while the lime tree nectar profile showed notable differences. Compared to lime tree nectar, a high amount of chrysin, pinocembrin, and galangin were detected in both ripe and unripe lime honey. Fructose and glucose were the major constituents of all investigated samples, and amounts were within the limits established by European Union legislation. Sucrose content in the nectar sample was up to two-fold higher when compared to all honey samples. Isomaltose and gentiobiose with turanose content were different in analyzed production stages of lime honey.

  3. Managing ecosystems without prior knowledge: pathological outcomes of lake liming

    Directory of Open Access Journals (Sweden)

    David G. Angeler

    2017-12-01

    Full Text Available Management actions often need to be taken in the absence of ecological information to mitigate the impact of pressing environmental problems. Managers counteracted the detrimental effects of cultural acidification on aquatic ecosystems during the industrial era using liming to salvage biodiversity and ecosystem services. However, historical contingencies, i.e., whether lakes were naturally acidic or degraded because of acidification, were largely unknown and therefore not accounted for in management. It is uncertain whether liming outcomes had a potentially detrimental effect on naturally acidic lakes. Evidence from paleolimnological reconstructions allowed us to analyze community structure in limed acidified and naturally acidic lakes, and acidified and circumneutral references. We analyzed community structure of phytoplankton, zooplankton, macroinvertebrates (littoral, sublittoral, profundal, and fish between 2000 and 2004. Naturally acidic limed lakes formed communities that were not representative of the other lake types. The occurrence of fish species relevant for ecosystem service provisioning (fisheries potential in naturally acidic limed lakes were confounded by biogeographical factors. In addition, sustained changes in water quality were conducive to harmful algal blooms. This highlights a pathological outcome of liming lakes when their naturally acidic conditions are not accounted for. Because liming is an important social-ecological system, sustained ecological change of lakes might incur undesired costs for societies in the long term.

  4. [Optimization of lime milk precipitation process of Lonicera Japonica aqueous extract based on quality by design concept].

    Science.gov (United States)

    Shen, Jin-Jing; Gong, Xing-Chu; Pan, Jian-Yang; Qu, Hai-Bin

    2017-03-01

    Design space approach was applied in this study to optimize the lime milk precipitation process of Lonicera Japonica (Jinyinhua) aqueous extract. The evaluation indices for this process were total organic acid purity and amounts of 6 organic acids obtained from per unit mass of medicinal materials. Four critical process parameters (CPPs) including drop speed of lime milk, pH value after adding lime milk, settling time and settling temperature were identified by using the weighted standardized partial regression coefficient method. Quantitative models between process evaluation indices and CPPs were established by a stepwise regression analysis. A design space was calculated by a Monte-Carlo simulation method, and then verified. The verification test results showed that the operation within the design space can guarantee the stability of the lime milk precipitation process. The recommended normal operation space is as follows: drop speed of lime milk of 1.00-1.25 mL•min⁻¹, pH value of 11.5-11.7, settling time of 1.0-1.2 h, and settling temperature of 10-20 ℃.. Copyright© by the Chinese Pharmaceutical Association.

  5. Lime utilization in the laboratory, field, and design of pavement layers : final report.

    Science.gov (United States)

    2017-01-01

    The objective of this study was to review and report the best practices of using lime (i.e., granulated lime, hydrated lime, and slurry lime) to dry soil, in working tables, and in pavement applications. The project also reviewed and documented the i...

  6. Use of lime cement stabilized pavement construction

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, M.A.; Raju, G.V.R.P. [JNTU College of Engineering, Kakinada (India). Dept. of Civil Engineering

    2009-08-15

    Expansive clay is a major source of heave induced structural distress. Swelling of expansive soils causes serious problems and produce damages to many structures. Many research organizations are doing extensive work on waste materials concerning the feasibility and environmental suitability. Fly ash, a waste by product from coal burning in thermal power stations, is abundant in India causing severe health, environmental and disposal problems. Attempts are made to investigate the stabilization process with model test tracks over expansive subgrade in flexible pavements. Cyclic plate load tests are carried out on the tracks with chemicals like lime and cement introduced in fly ash subbase laid on sand and expansive subgrades. Test results show that maximum load carrying capacity is obtained for stabilized fly ash subbase compared to untreated fly ash subbase.

  7. Growth and nutrition of coniferous forests on acidic mineral soils - status and effects of liming and fertilization

    International Nuclear Information System (INIS)

    Sikstroem, Ulf

    2001-01-01

    Deposited air-borne S- and N- containing pollutants acidify forest soils in southern Sweden. It has been suggested that this may severely affect forest yield. Liming and/or application of specific nutrients, e.g. phosphorus (P) and potassium (K), have been proposed as countermeasures. The influence of such measures, and of nitrogen (N) addition, was investigated in two experimental series over 5-10 years. Stem growth and needle element concentrations were assessed, predominantly in high-yielding Norway spruce [Picea abies (L.) Karst.] and Scots pine (Pinus sylvestris L.) stands, 30-60 years old, growing on acidic mineral soils in southern Sweden. The effect on crown transparency was also evaluated in some of the Norway spruce stands. The treatments included liming (500-6,000 kg ha -1 ), and N addition at low annual doses (2x10 kg N ha -1 ) and in single shots (150 kg N ha -1 ). Combinations of lime+N, lime+PK and lime+PKN were also tested. The effects were generally weak or negligible, except that growth was significantly increased by N fertilization in the Scots pine stands, and by lime+PKN in some of the Norway spruce stands. In another study, the survival and growth of Norway spruce seedlings were found to be more or less unaffected when planted in pre-harvest acidified, limed or N fertilized soil, although the Ca and Zn concentrations in their needles rose after liming, while those of Mn and Al declined. In closed-canopy stands of Norway spruce and Scots pine with N concentrations of more than 15-16 mg (g DM) -1 in current-year needles, N fertilization was indicated to not necessarily stimulate increased growth. Other indicators of highly N-rich forests (e.g. elevated arginine levels) also start to appear above this level. The closed-canopy stands growing on the most acidic soils showed no signs of severe damage or nutrient deficiencies. These findings, together with the small or negligible effects of the tested countermeasures against soil acidification

  8. Nonlinear dynamics of spring softening and hardening in folded-mems comb drive resonators

    KAUST Repository

    Elshurafa, Amro M.; Khirallah, Kareem; Tawfik, Hani H.; Emira, Ahmed; Abdel Aziz, Ahmed K S; Sedky, Sherif M.

    2011-01-01

    This paper studies analytically and numerically the spring softening and hardening phenomena that occur in electrostatically actuated microelectromechanical systems comb drive resonators utilizing folded suspension beams. An analytical expression

  9. Acoustic softening in metals during ultrasonic assisted deformation via CP-FEM

    KAUST Repository

    Siddiq, Amir; El Sayed, Tamer S.

    2011-01-01

    In this paper, a phenomenological crystal plasticity model is modified to account for acoustic (ultrasonic) softening effects based on the level of ultrasonic intensity supplied to single and polycrystalline metals. The material parameters

  10. Optimization of hardening/softening behavior of plane frame structures using nonlinear normal modes

    DEFF Research Database (Denmark)

    Dou, Suguang; Jensen, Jakob Søndergaard

    2016-01-01

    Devices that exploit essential nonlinear behavior such as hardening/softening and inter-modal coupling effects are increasingly used in engineering and fundamental studies. Based on nonlinear normal modes, we present a gradient-based structural optimization method for tailoring the hardening...... involving plane frame structures where the hardening/softening behavior is qualitatively and quantitatively tuned by simple changes in the geometry of the structures....

  11. Plasticity, Swell-Shrink, and Microstructure of Phosphogypsum Admixed Lime Stabilized Expansive Soil

    OpenAIRE

    James, Jijo; Pandian, P. Kasinatha

    2016-01-01

    The study involved utilization of an industrial waste, Phosphogypsum (PG), as an additive to lime stabilization of an expansive soil. Three lime dosages, namely, initial consumption of lime (ICL), optimum lime content (OLC), and less than ICL (LICL), were identified for the soil under study for stabilizing the soil. Along with lime, varying doses of PG were added to the soil for stabilization. The effect of stabilization was studied by performing index tests, namely, liquid limit, plastic lim...

  12. Cost-benefit analysis of central softening for production of drinking water.

    Science.gov (United States)

    Van der Bruggen, B; Goossens, H; Everard, P A; Stemgée, K; Rogge, W

    2009-01-01

    Softening drinking water before distribution yields advantages with environmental impact, such as lower household products consumption, less scaling in piping and machines, and the avoidance of decentralized, domestic softeners. Central softening is under consideration in Flanders by the largest water supplier, VMW (Dutch acronym for "Flemish Company for Water Supply"), to deliver soft (15 degrees F) water to their customers. A case study is presented for a region with hard water (47 degrees F). The chosen technique is the pellet reactor, based on precipitation of CaCO(3) by NaOH addition. This softening operation has possibly large impact on the environment and the water consumption pattern. A cost-benefit analysis has been made to estimate the added value of central softening, by investigating the impact on the drinking water company, on their customers, on employment, on environment, on health, etc. The analysis for the region of study revealed benefits for customers which were higher than the costs for the drinking water company. However, pricing of drinking water remains an important problem. A sensitivity analysis of these results has also been made, to evaluate the impact of important hypothesis, and to be able to expand this study to other regions. The conclusions for this part show that softening is beneficial if water hardness is to be decreased by at least 5 degrees F.

  13. Economic evaluation of the industrial solar production of lime

    International Nuclear Information System (INIS)

    Meier, Anton; Gremaud, Nicolas; Steinfeld, Aldo

    2005-01-01

    The use of concentrated solar energy in place of fossil fuels for driving the endothermic calcination reaction CaCO 3 → CaO + CO 2 at above 1300 K has the potential of reducing CO 2 emissions by 20% in a state-of-the-art lime plant and up to 40% in a conventional cement plant. An economic assessment for an industrial solar calcination plant with 25 MW th solar input indicates that the cost of solar produced lime ranges between 128 and 157 $/t, about twice the current selling price of conventional lime. The solar production of high purity lime for special sectors in the chemical and pharmaceutical industry might be competitive with conventional fossil fuel based calcination processes at current fuel prices

  14. occupational health problems studied among the workers of lime

    African Journals Online (AJOL)

    RAMGANES

    In present study, an extensive health survey of 573 lime kiln workers of Maihar and Jhukehi region of ... Among the observed health anomalies, ..... Health benefits of air pollution control in ... “Association of Indoor and Outdoor Particulate.

  15. Ring Formation in Lime Kilns; Ringbildning i Mesaugnar II

    Energy Technology Data Exchange (ETDEWEB)

    Dhak, Janice [AaF-Process AB, Stockholm (Sweden)

    2003-07-15

    The key to a cost efficient and high performance pulp production is low variations in the production level. Despite the fact that all pulp mills always work with improvements to eliminate problems with ring formations, AaF has at several mill seen that the operation of a lime kiln still often is disturbed by ring formation. In 1999 AAF made an extensive investigation of more than 10 lime kilns in Sweden, considering operational data, kiln data and lime chemical analyzes. The result pointed out the importance of how the lime kiln is operated and that dead load and contaminants in the lime was less important. The report suggested that it is the difference in the temperature between the flue gas and the lime that is of importance. There are no quantified process values available that guides for a 'best practice' way to run a lime kiln to avoid ring formation. The goal with this project has been to develop a strategy for operation of a kiln in a way that lowers the risk for ring formation. The results from simulations of a number of lime kilns in this project could not proof that a low difference in the temperature between the flue gas and the lime was the main cause of problems with ring formation and thus it was not possible to quantify the optimal difference to avoid rings. Probably the most important information from the simulations was that it is not the temperature difference in number of degrees that is of importance, rather the fact that the temperature difference in the kalcining zone varies, and time to time reach below the critical level were lime occasionally is cooled down. It can be the case if the temperature profile of the flue gas temporarily changes or if the lime mud temperature profile is changed. The reason for changes in the temperature profile is discussed in the report. The most important factors discussed are: Variations in the energy input e.g. oil and methanol/strong gases in cocombustion. One single fuel is easier to control

  16. Producer gas and its use for the manufacture of lime

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, A K; Kumar, S

    1976-04-01

    An analysis of available data indicates that coal-based producer gas is superior to coal or wood as a fuel for lime kilns and much more readily available than oil or natural gas. With producer gas, chemical-grade lime is obtained, and the kiln capacity is increased, so that a smaller unit can be used or more lime obtained. With a mixture of coal and wood as the fuel, the lime produced is contaminated with ash. The added cost of the gas-producer unit can be paid out in one year owing to the greater demand for and the consequent higher prices obtainable for the chemical-grade product. In addition, the flue gases from the kiln can be used in place of steam to heat the gas producer, but experimental studies are needed to determine the magnitude of the savings in fuel consumption. 15 references.

  17. Analysis on soil compressibility changes of samples stabilized with lime

    Directory of Open Access Journals (Sweden)

    Elena-Andreea CALARASU

    2016-12-01

    Full Text Available In order to manage and control the stability of buildings located on difficult foundation soils, several techniques of soil stabilization were developed and applied worldwide. Taking into account the major significance of soil compressibility on construction durability and safety, the soil stabilization with a binder like lime is considered one of the most used and traditional methods. The present paper aims to assess the effect of lime content on soil geotechnical parameters, especially on compressibility ones, based on laboratory experimental tests, for several soil categories in admixture with different lime dosages. The results of this study indicate a significant improvement of stabilized soil parameters, such as compressibility and plasticity, in comparison with natural samples. The effect of lime stabilization is related to an increase of soil structure stability by increasing the bearing capacity.

  18. Audiovisual Documentation of an International Seminar : Case: LIME

    OpenAIRE

    Tikkanen, Kirsti; Rönnberg, Mira

    2013-01-01

    The aim of this Bachelor’s thesis is to create a documentary video of an international seminar held in Kerava, Finland, in June 2013. The seminar was called Learning on Immigration and Multicultural Education (LIME) and it was conducted by Kerava Adult Education Center (later Keravan Opisto). LIME was a two-year intercultural project funded by the European Union. Different non-governmental organizations and adult education centers from eight European countries took part on the project. The ai...

  19. Lime helps establish crownvetch on coal-breaker refuse

    Science.gov (United States)

    Miroslaw M. Czapowskyj; Edward A. Sowa

    1976-01-01

    A study was begun in 1965 to determine the effect of lime fertilizer, and mulch on the establishment and growth of crownvetch crowns planted on anthracite coal-breaker refuse. After 7 years the lime application had by far the strongest effect. Both 2.5 and 5.0 tons per acre increased survival and ground cover manyfold, and both treatments were equally beneficial from...

  20. Elemental analysis of Taiwanese areca nut and limes with INAA

    International Nuclear Information System (INIS)

    Wei, Y.Y.; Chung, C.

    1997-01-01

    The popular areca nuts were sampled and their stuffed white and red lime were collected simultaneously from four marketplaces in Taiwan in different growing seasons. Samples of areca nut were treated via homogenizer prior to freeze drying, about 100-150 mg each of the areca nut and lime were packed into PE bag. Samples were irradiated with neutron flux about 10 12 n x cm -2 x s -1 . A total of 17, 18, and 13 elements was analyzed with INAA for white lime, red lime, and areca nut, respectively. The results indicated that Ca have the highest concentration in both limes. Most elements in collected samples have wide range of concentrations among different seasons and marketplaces. It is suggested that the elemental concentration of areca nut and limes exists in divergence originated from various farms in Taiwan. In addition, four elements of Ca, Fe, Mg, and Sc are probably overtaken by persons having chewing habit of areca nut and their effects on oral cancer are discussed. (author)

  1. Normal and Fibrotic Rat Livers Demonstrate Shear Strain Softening and Compression Stiffening: A Model for Soft Tissue Mechanics.

    Directory of Open Access Journals (Sweden)

    Maryna Perepelyuk

    Full Text Available Tissues including liver stiffen and acquire more extracellular matrix with fibrosis. The relationship between matrix content and stiffness, however, is non-linear, and stiffness is only one component of tissue mechanics. The mechanical response of tissues such as liver to physiological stresses is not well described, and models of tissue mechanics are limited. To better understand the mechanics of the normal and fibrotic rat liver, we carried out a series of studies using parallel plate rheometry, measuring the response to compressive, extensional, and shear strains. We found that the shear storage and loss moduli G' and G" and the apparent Young's moduli measured by uniaxial strain orthogonal to the shear direction increased markedly with both progressive fibrosis and increasing compression, that livers shear strain softened, and that significant increases in shear modulus with compressional stress occurred within a range consistent with increased sinusoidal pressures in liver disease. Proteoglycan content and integrin-matrix interactions were significant determinants of liver mechanics, particularly in compression. We propose a new non-linear constitutive model of the liver. A key feature of this model is that, while it assumes overall liver incompressibility, it takes into account water flow and solid phase compressibility. In sum, we report a detailed study of non-linear liver mechanics under physiological strains in the normal state, early fibrosis, and late fibrosis. We propose a constitutive model that captures compression stiffening, tension softening, and shear softening, and can be understood in terms of the cellular and matrix components of the liver.

  2. Long-term influence of liming on biological availability of radiocaesium in forest soils

    International Nuclear Information System (INIS)

    Konoplev, A.V.; Drissner, J.; Klemt, E.; Miller, R.; Zibold, G.; Konopleva, I.V.

    1998-01-01

    The results of research of 137 Cs transfer from soil to plants are presented for a spruce (Picea abies) forest plot in Baden-Wuerttemberg, Germany, 13 years after fertilization (83% CaCO 3 , 8% MgO, 6% K 2 O, 3% P 2 O 5 , 2.5 t/ha, 1984). Liming was found to result in a long-term decrease of the 137 Cs uptake by plants by a factor of 8-20 in comparison with the control plot. The results of liming include morphological changes of litter and characteristics of rooty soil layer: the parameters of caesium selective sorption and composition of a soil solution determining the biological availability of 137 Cs. The 137 Cs accumulation factors for forest plants were predicted based on a model of radiocaesium soil-to-plant transfer. The theoretical assessments are compared with experimental data

  3. Experimental Effects of Lime Application on Aquatic Macrophytes: 2. Growth Response Versus Treatment Time and Lime Concentration

    National Research Council Canada - National Science Library

    James, William F; Barko, John W

    2006-01-01

    This research investigated the effects of applying lime (as calcium hydroxide; Ca(OH)2) either early or later in the life cycle on the growth, survivorship, and reproductive success of Sago Pondweed...

  4. Study of lime vs. no lime in cold in-place recycled asphalt concrete pavements : final report.

    Science.gov (United States)

    1991-09-01

    The resilient characteristics of cold in-place recycled asphalt concrete with and without lime were examined. Six core samples were obtained from a site two months after construction; six months later, six additional core samples were obtained from t...

  5. Thermal energy analysis of a lime production process: Rotary kiln, preheater and cooler

    International Nuclear Information System (INIS)

    Shahin, Hamed; Hassanpour, Saeid; Saboonchi, Ahmad

    2016-01-01

    Highlights: • The integrated model for lime production unit which includes cooler, preheater and rotary kiln is developed. • The effect of residence time in each section on efficiency is investigated. • Influence of material feed rate and excess air on specific fuel consumption is analyzed. • The significant effect of particle size on efficiency and specific fuel consumption is shown. - Abstract: In this paper, thermal energy analysis of three zones of a lime production process, which are preheater, rotary kiln and cooler, is performed. In order to perform a proper quantitative estimation, the system was modeled using energy balance equations including coupled heat transfer and chemical reaction mechanisms. A mathematical model was developed, and consequently, the thermal and chemical behavior of limestone was investigated. The model was verified using empirical data. After model confirmation, the variation of Specific Fuel Consumption (SFC) versus production rate was predicted and the optimum condition was determined. Subsequently, fuel consumption was calculated regarding to altered residence time inside each zone of lime production process, for a constant output. Results indicate that increasing the residence time inside each zone of lime production process, will enhance thermal efficiency and saves fuel consumption. Relative enhancement will be the same for different sizes of limestone. It was found that a 10-min increase in material residence time inside the preheater or rotary kiln can reduce fuel consumption by around two percent. Whereas, a 5-min increase in material residence time inside the cooler would be enough to obtain a similar result. Finally, the ratio of air-to-fuel and production rate are changed in such a way that the same product is achieved. The model predicts that lowering excess air from 15% to 10% leads to a 2.5% reduction of Specific Fuel Consumption (SFC).

  6. Interpretation of the lime column penetration test

    International Nuclear Information System (INIS)

    Liyanapathirana, D S; Kelly, R B

    2010-01-01

    Dry soil mix (DSM) columns are used to reduce the settlement and to improve the stability of embankments constructed on soft clays. During construction the shear strength of the columns needs to be confirmed for compliance with technical assumptions. A specialized blade shaped penetrometer known as the lime column probe, has been developed for testing DSM columns. This test can be carried out as a pull out resistance test (PORT) or a push in resistance test (PIRT). The test is considered to be more representative of average column shear strength than methods that test only a limited area of the column. Both PORT and PIRT tests require empirical correlations of measured resistance to an absolute measure of shear strength, in a similar manner to the cone penetration test. In this paper, finite element method is used to assess the probe factor, N, for the PORT test. Due to the large soil deformations around the probe, an Arbitrary Lagrangian Eulerian (ALE) based finite element formulation has been used. Variation of N with rigidity index and the friction at the probe-soil interface are investigated to establish a range for the probe factor.

  7. Lime Juice and Vinegar Injections as a Cheap and Natural Alternative to Control COTS Outbreaks.

    Science.gov (United States)

    Moutardier, Grégoire; Gereva, Sompert; Mills, Suzanne C; Adjeroud, Mehdi; Beldade, Ricardo; Ham, Jayven; Kaku, Rocky; Dumas, Pascal

    2015-01-01

    Outbreaks of the corallivorous crown-of-thorns seastar Acanthaster planci (COTS) represent one of the greatest disturbances to coral reef ecosystems in the Indo-Pacific, affecting not only coral reefs but also the coastal communities which rely on their resources. While injection approaches are increasingly used in an attempt to control COTS densities, most of them display severe drawbacks including logistical challenges, high residual environmental impacts or low cost-effectiveness. We tested a new alternative control method based upon acidic injections of cheap, 100% natural products. We investigated the lethal doses, intra- and inter-specific disease transmission and immune responses of COTS when injected with fresh lime juice (extracted from local Citrus arantifolia) and white spirit vinegar. High COTS mortality was achieved with small volumes: 10-20 ml per seastar induced death in 89%/97% of injected specimens after an average 34.3 h/29.8 h for lime juice and vinegar respectively. Highest efficiency was reached for both solutions with double shots of (2 × 10 ml) in two different areas on the body: 100% mortality occurred within 12-24 h, which is similar or faster compared with other current injection methods. Multiple immune measures suggested that death was very likely caused by pH stress from the acidic solutions rather than a bacterial infection. Contagion to either conspecifics or a variety of other reef species was not observed, even at COTS densities 15 times higher than the highest naturally reported. 10 to 20 l lime juice/vinegar could kill up to a thousand COTS at a cost of less than 0.05 USD per specimen; no permits or special handling procedures are required. We conclude that injections of lime juice and vinegar offer great advantages when compared to current best practises and constitute a cheap and natural option for all reefs affected by COTS.

  8. Lime and gypsum application on the wheat crop

    Directory of Open Access Journals (Sweden)

    Caires Eduardo Fávero

    2002-01-01

    Full Text Available Root growth and crop yield can be affected by chemical modifications of the soil profile owing to lime and gypsum applications. A field trial was carried out on a dystrophic Clayey Rhodic Hapludox at Ponta Grossa, PR, Brazil, aiming to evaluate lime (without or with incorporation into the soil and gypsum effects on root growth, mineral nutrition and grain yield of wheat (cv. OR 1. A randomized complete block design was used, with three replications, in a split-plot experiment. Treatments with dolomitic limestone (without lime and 4.5 t ha-1 of lime applied on the surface, in total rate and 1/3 of the requirement per year during 3 years, or incorporated into the soil were applied in July 1998 (main plots and the rates of gypsum (0, 3, 6 and 9 t ha-1 in October 1998 (subplots. Wheat was evaluated in the 2000 winter season. In conditions of water deficit absence, there was no limitation in root growth in depth, for exchangeable Ca of 6 mmol c dm-3. Lime incorporation of lime increased the Mg concentration in the leaves, but wheat yield was not influenced by the correction of soil acidity through liming treatments. Gypsum increased the concentrations of Ca and S in wheat leaves, with significant effects on grain yield. The critical level of S-SO4(2- in the 0-20 cm soil layer, extracted by ammonium acetate 0.5 mol L-1 in acetic acid 0.25 mol L-1, was 25.8 mg dm-3.

  9. Employing natural reagents from turmeric and lime for acetic acid determination in vinegar sample.

    Science.gov (United States)

    Supharoek, Sam-Ang; Ponhong, Kraingkrai; Siriangkhawut, Watsaka; Grudpan, Kate

    2018-04-01

    A simple, rapid and environmentally friendly sequential injection analysis system employing natural extract reagents was developed for the determination of acetic acid following an acid-base reaction in the presence of an indicator. Powdered lime and turmeric were utilized as the natural base and indicator, respectively. Mixing lime and turmeric produced an orange to reddish-brown color solution which absorbed the maximum wavelength at 455 nm, with absorbance decreasing with increasing acetic acid concentration. Influential parameters including lime and turmeric concentrations, reagent and sample aspirated volumes, mixing coil length and dispensing flow rate were investigated and optimized. A standard calibration graph was plotted for 0-5.0 mmol/L acetic acid with r 2  = 0.9925. Relative standard deviations (RSD) at 2.0 and 4.0 mmol/L acetic acid were less than 3% (n = 7), with limit of detection (LOD) and limit of quantification (LOQ) at 0.12 and 0.24 mmol/L, respectively. The method was successfully applied to assay acetic acid concentration in cooking vinegar samples. Results achieved were not significantly different from those obtained following a batchwise standard AOAC titration method. Copyright © 2017. Published by Elsevier B.V.

  10. Combined data mining/NIR spectroscopy for purity assessment of lime juice

    Science.gov (United States)

    Shafiee, Sahameh; Minaei, Saeid

    2018-06-01

    This paper reports the data mining study on the NIR spectrum of lime juice samples to determine their purity (natural or synthetic). NIR spectra for 72 pure and synthetic lime juice samples were recorded in reflectance mode. Sample outliers were removed using PCA analysis. Different data mining techniques for feature selection (Genetic Algorithm (GA)) and classification (including the radial basis function (RBF) network, Support Vector Machine (SVM), and Random Forest (RF) tree) were employed. Based on the results, SVM proved to be the most accurate classifier as it achieved the highest accuracy (97%) using the raw spectrum information. The classifier accuracy dropped to 93% when selected feature vector by GA search method was applied as classifier input. It can be concluded that some relevant features which produce good performance with the SVM classifier are removed by feature selection. Also, reduced spectra using PCA do not show acceptable performance (total accuracy of 66% by RBFNN), which indicates that dimensional reduction methods such as PCA do not always lead to more accurate results. These findings demonstrate the potential of data mining combination with near-infrared spectroscopy for monitoring lime juice quality in terms of natural or synthetic nature.

  11. Ultrasonically assisted drilling: A finite-element model incorporating acoustic softening effects

    International Nuclear Information System (INIS)

    Phadnis, V A; Roy, A; Silberschmidt, V V

    2013-01-01

    Ultrasonically assisted drilling (UAD) is a novel machining technique suitable for drilling in hard-to-machine quasi-brittle materials such as carbon fibre reinforced polymer composites (CFRP). UAD has been shown to possess several advantages compared to conventional drilling (CD), including reduced thrust forces, diminished burr formation at drill exit and an overall improvement in roundness and surface finish of the drilled hole. Recently, our in-house experiments of UAD in CFRP composites demonstrated remarkable reductions in thrust-force and torque measurements (average force reductions in excess of 80%) when compared to CD with the same machining parameters. In this study, a 3D finite-element model of drilling in CFRP is developed. In order to model acoustic (ultrasonic) softening effects, a phenomenological model, which accounts for ultrasonically induced plastic strain, was implemented in ABAQUS/Explicit. The model also accounts for dynamic frictional effects, which also contribute to the overall improved machining characteristics in UAD. The model is validated with experimental findings, where an excellent correlation between the reduced thrust force and torque magnitude was achieved

  12. Significance, evolution and recent advances in adsorption technology, materials and processes for desalination, water softening and salt removal.

    Science.gov (United States)

    Alaei Shahmirzadi, Mohammad Amin; Hosseini, Seyed Saeid; Luo, Jianquan; Ortiz, Inmaculada

    2018-06-01

    Desalination and softening of sea, brackish, and ground water are becoming increasingly important solutions to overcome water shortage challenges. Various technologies have been developed for salt removal from water resources including multi-stage flash, multi-effect distillation, ion exchange, reverse osmosis, nanofiltration, electrodialysis, as well as adsorption. Recently, removal of solutes by adsorption onto selective adsorbents has shown promising perspectives. Different types of adsorbents such as zeolites, carbon nanotubes (CNTs), activated carbons, graphenes, magnetic adsorbents, and low-cost adsorbents (natural materials, industrial by-products and wastes, bio-sorbents, and biopolymer) have been synthesized and examined for salt removal from aqueous solutions. It is obvious from literature that the existing adsorbents have good potentials for desalination and water softening. Besides, nano-adsorbents have desirable surface area and adsorption capacity, though are not found at economically viable prices and still have challenges in recovery and reuse. On the other hand, natural and modified adsorbents seem to be efficient alternatives for this application compared to other types of adsorbents due to their availability and low cost. Some novel adsorbents are also emerging. Generally, there are a few issues such as low selectivity and adsorption capacity, process efficiency, complexity in preparation or synthesis, and problems associated to recovery and reuse that require considerable improvements in research and process development. Moreover, large-scale applications of sorbents and their practical utility need to be evaluated for possible commercialization and scale up. Copyright © 2018 Elsevier Ltd. All rights reserved.

  13. LIME EFFECTIVENESS OF SOME FERTILIZERS IN A TROPICAL ACID ALFISOL

    Directory of Open Access Journals (Sweden)

    Mercy Omogbohu Anetor

    2007-11-01

    Full Text Available Liming increases production costs and environmentally unfriendly. Effectiveness of crystalliser (CRYS, single super phosphate (SSP and organic fertilizer (OF for liming was evaluated by determining pH and phosphorus- (P- availability in an acid alfisol incubated with the amendments, Ca(OH2 being reference. Treatments were replicated thrice in completely randomised design. Un-amended soil remained acidic (pH 4.8 but liming raised pH (6.1-6.6, enhancing maximum (15.09-17.33 mg kg-1 P–release (un-amended having 4.24-7.09 mg P kg-1. Lime (L and L+P treatments resulted in maximum pH increases (7.0-7.2, decreasing with incubation. Fertilizer treatments also raised pH (5.0-5.5 for OF, CRYS or SSP; 5.6-5.8 for CRYS +SSP, CRYS+OF and OF+SSP relative to control (5.2. Acid soil infertility-ameliorating potential of CRYS and OF was revealed. They could be used multi-purposely as lime and P fertilizers by poor-resource farmers challenged by acid soil infertility factors.

  14. Soil Stabilization with Lime for the Construction of Forest Roads

    Directory of Open Access Journals (Sweden)

    Reginaldo Sérgio Pereira

    2018-02-01

    Full Text Available ABSTRACT The mechanical performance of soil stabilization using lime to improve forest roads was assessed. This study was conducted with lateritic soil (LVAd30 using lime content of 2% in the municipality of Niquelândia, Goiás state, Brazil. Geotechnical tests of soil characterization, compaction, and mechanical strength were performed applying different compaction efforts and curing periods. The results showed that lime content significantly changed the mechanical performance of natural soil, increasing its mechanical strength and load-carrying capacity. Compaction effort and curing time provided different responses in the unconfined compressive strength (UCS and California Bearing Ratio (CBR tests. The best UCS value (786.59 kPa for the soil-lime mixture was achieved with modified compaction effort and curing time of 28 days. In the CBR test, soil-lime mixtures compacted at intermediate and modified efforts and cured for 28 days were considered for application as subbase material of flexible road pavements, being a promising alternative for use in layers of forest roads.

  15. The use of hydrated lime in acid mine drainage treatment

    Science.gov (United States)

    Othman, Anuar; Sulaiman, Azli; Sulaiman, Shamsul Kamal

    2017-05-01

    Hydrated lime also known as calcium hydroxide with chemical formula Ca(OH)2 was used in this study as neutralization agent in acid mine drainage (AMD) treatment. Hydrated lime that is used to treat pool water samples from tin tailings located in Pengkalan Hulu, Perak was obtained from Simpang Pulai, Perak. The pH of water sample was around 2.6 to 2.8. Ten different variables of hydrated lime weights were used to treat 1 L of water sample. The weights of hydrated lime used were 0.2 g, 0.4 g, 0.6 g, 0.8 g, 1.0 g, 1.2 g, 1.4 g, 1.6 g, 1.8 g and 2.0 g. Time interval used was every 5 minutes up to minutes 30. Jar test method was used in this study. The maximum pH value of 5.93 ± 0.03 most approaches standard A and had complied standard B have been obtained using 2.0 g hydrated lime in 30-minute time interval. The concentration of arsenic, cadmium and chromium had decreased but only cadmium concentration did not comply with Standards A and B.

  16. Sweet cherry softening accompanied with moisture migration and loss during low-temperature storage.

    Science.gov (United States)

    Zhu, Danshi; Liang, Jieyu; Liu, He; Cao, Xuehui; Ge, Yonghong; Li, Jianrong

    2017-12-18

    Hardness is one of the important qualities influencing consumer appeal and marketing of fresh sweet cherry (Prunus avium L.). Moisture loss is one of the main causative factors of cherry softening. In this work, moisture loss and softening process of sweet cherry during postharvest storage at 0 and 4 °C were studied. In addition, low-field 1 H nuclear magnetic resonance (LF-NMR) was used to analyze water distribution and migration in sweet cherry during storage at 4 °C. Moisture content correlated significantly (p Contents of cytoplasmic (p content increased gradually, and then internal damage occurred. Sweet cherry softening closely correlated with moisture loss during low-temperature storage. LF-NMR is a useful technique to investigate moisture migration of fruits and vegetables. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  17. Regularized finite element modeling of progressive failure in soils within nonlocal softening plasticity

    Science.gov (United States)

    Huang, Maosong; Qu, Xie; Lü, Xilin

    2017-11-01

    By solving a nonlinear complementarity problem for the consistency condition, an improved implicit stress return iterative algorithm for a generalized over-nonlocal strain softening plasticity was proposed, and the consistent tangent matrix was obtained. The proposed algorithm was embodied into existing finite element codes, and it enables the nonlocal regularization of ill-posed boundary value problem caused by the pressure independent and dependent strain softening plasticity. The algorithm was verified by the numerical modeling of strain localization in a plane strain compression test. The results showed that a fast convergence can be achieved and the mesh-dependency caused by strain softening can be effectively eliminated. The influences of hardening modulus and material characteristic length on the simulation were obtained. The proposed algorithm was further used in the simulations of the bearing capacity of a strip footing; the results are mesh-independent, and the progressive failure process of the soil was well captured.

  18. Creep deformation of high Cr-Mo ferritic/martensitic steels by material softening

    International Nuclear Information System (INIS)

    Kim, Sung Ho; Song, B. J.; Ryu, Woo Seog

    2005-01-01

    High Cr (9-12%Cr) ferritic/martensitic steels represent a valuable alternative to austenitic stainless steel for high temperature applications up to 600 .deg. C both in power and petrochemical plant, as well as good resistance to oxidation and corrosion. Material softening is the main physical phenomenon observed in the crept material. Thermally-induced change (such as particle coarsening or matrix solute depletion) and strain-induced change (such as dynamic subgrain growth) of microstructure degraded the alloy strength. These microstructural changes during a creep test cause the material softening, so the strength of the materials decreased. Many researches have been performed for the microstructural changes during a creep test, but the strength of crept materials has not been measured. In the present work, we measured the yield and tensile strength of crept materials using Indentationtyped Tensile Test System (AIS 2000). Material softening was quantitatively evaluated with a creep test condition, such as temperature and applied stress

  19. Communication: Surface-facilitated softening of ordinary and vapor-deposited glasses

    Science.gov (United States)

    Cubeta, Ulyana; Bhattacharya, Deepanjan; Sadtchenko, Vlad

    2017-08-01

    A common distinction between the ordinary glasses formed by melt cooling and the stable amorphous films formed by vapor deposition is the apparent mechanism of their devitrification. Using quasi-adiabatic, fast scanning calorimetry that is capable of heating rates in excess of 105 K s-1, we have investigated the softening kinetics of micrometer-scale, ordinary glass films of methylbenzene and 2-propanol. At the limit of high heating rates, the transformation mechanism of ordinary glasses is identical to that of their stable vapor-deposited counterparts. In both cases, softening is likely to begin at the sample surface and progress into its bulk via a transformation front. Furthermore, such a surface-facilitated mechanism complies with zero-order, Arrhenius rate law. The activation energy barriers for the softening transformation imply that the kinetics must be defined, at least in part, by the initial thermodynamic and structural state of the samples.

  20. Influence of amino-functional macro and micro silicone softeners on the properties of cotton fabric

    International Nuclear Information System (INIS)

    Jatoi, A.W.; Khatri, Z.

    2015-01-01

    Amino-functional silicone softeners are most widely used type of soft finishes owing to their outstanding permanent softness, smoothness and handle characteristics. These soft finishes are prepared in different emulsion droplet sizes such as macro and micro emulsions providing varying characteristics on the textile on which they are applied. The macroemulsions due to their larger droplet sizes lubricate fabric and yarn surfaces, while the micro-emulsion, thanks to their smaller sizes penetrate inside fiber pores. In this research amino-functional macro and micro emulsions have been applied on dyed cotton fabric in 1:1 combination and compared against their influence on physical properties such as bending length, abrasion resistance, tensile strength, crease resistance and water repellency. These emulsions have also been compared for their influence on colorimetric properties; color difference and color strength (K/S values). The results reveal that the softener application in combination improves the properties deteriorated by each softener when applied separately. (author)

  1. Enamel softening with Coca-Cola and rehardening with milk or saliva.

    Science.gov (United States)

    Gedalia, I; Dakuar, A; Shapira, L; Lewinstein, I; Goultschin, J; Rahamim, E

    1991-06-01

    Rehardening effects by cow's milk and by secreted saliva were investigated, in situ, following softening of human enamel with an acidic beverage (Coca-Cola). Volunteers wearing orthodontic removable appliances participated in the study. The intra-oral test was chosen for measuring microhardness of enamel slabs inserted into the dental appliance. The softening and the rehardening degrees were defined as the alterations between initial- and experimental-microhardness value at the enamel surface. In addition, SEM photos were prepared from the initial and experimental stages. Exposure of enamel slabs to the acidic beverage during 1 hour had a softening effect as expressed by the hardness decrease and visualized by the SEM photo. Rehardening effects following milk or saliva exposures respectively were evident, presumably due to deposited organic and mineral material on the enamel surface.

  2. STUDY ON SOFTENING AND DROPPING PROPERTIES OF METALIZED BURDEN INSIDE BLAST FURNACE

    Directory of Open Access Journals (Sweden)

    Bi-yang Tuo

    2014-12-01

    Full Text Available The inferences of burden metallization rate on softening-melting dropping properties were investigated through softening-melting dropping test of three kinds of metalized burden pressure drop. The results indicated that the softeningmelting temperature interval of pre-reduction mixed burden is bigger than primeval mixed burden, the melting interval narrow with the rise of metallization rate of ferric burden as well as dropping temperature interval. The average pressure drop, maximum pressure drop and softening-melting dropping properties eigenvalue decrease with the rise of metallization rate of ferric burden. Besides, the dropping temperature of burden reduces with the rise of carbon content of molten iron. The combination high metalized burden and higher carbon content of molten iron is benefit to decreasing thickness of cohesive zone and improve permeability of cohesive zone.

  3. Modelling irradiation-induced softening in BCC iron by crystal plasticity approach

    International Nuclear Information System (INIS)

    Xiao, Xiazi; Terentyev, Dmitry; Yu, Long; Song, Dingkun; Bakaev, A.; Duan, Huiling

    2015-01-01

    Crystal plasticity model (CPM) for BCC iron to account for radiation-induced strain softening is proposed. CPM is based on the plastically-driven and thermally-activated removal of dislocation loops. Atomistic simulations are applied to parameterize dislocation-defect interactions. Combining experimental microstructures, defect-hardening/absorption rules from atomistic simulations, and CPM fitted to properties of non-irradiated iron, the model achieves a good agreement with experimental data regarding radiation-induced strain softening and flow stress increase under neutron irradiation. - Highlights: • A stress- and thermal-activated defect absorption model is proposed for the dislocation-loop interaction. • A temperature-dependent plasticity theory is proposed for the irradiation-induced strain softening of irradiated BCC metals. • The numerical results of the model match with the corresponding experimental data.

  4. Softened food reduces weight loss in the streptozotocin-induced male mouse model of diabetic nephropathy

    DEFF Research Database (Denmark)

    Nørgaard, Sisse A; Sand, Fredrik W; Sørensen, Dorte B

    2018-01-01

    The streptozotocin (STZ)-induced diabetic mouse is a widely used model of diabetes and diabetic nephropathy (DN). However, it is a well-known issue that this model is challenged by high weight loss, which despite supportive measures often results in high euthanization rates. To overcome...... these issues, we hypothesized that supplementing STZ-induced diabetic mice with water-softened chow in addition to normal chow would reduce weight loss, lower the need for supportive treatment, and reduce the number of mice reaching the humane endpoint of 20% weight loss. In a 15 week STZ-induced DN study we...... demonstrated that diabetic male mice receiving softened chow had reduced acute weight loss following STZ treatment ( p = 0.045) and additionally fewer mice were euthanized due to weight loss. By supplementing the diabetic mice with softened chow, no mice reached 20% weight loss whereas 37.5% of the mice...

  5. Modelling irradiation-induced softening in BCC iron by crystal plasticity approach

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Xiazi [State Key Laboratory for Turbulence and Complex System, Department of Mechanics and Engineering Science, College of Engineering, Peking University, Beijing 100871 (China); CAPT, HEDPS and IFSA Collaborative Innovation Center of MoE, Peking University, Beijing 100871 (China); Terentyev, Dmitry, E-mail: dterenty@SCKCEN.BE [Structural Material Group, Institute of Nuclear Materials Science, SCK-CEN, Mol (Belgium); Yu, Long; Song, Dingkun [State Key Laboratory for Turbulence and Complex System, Department of Mechanics and Engineering Science, College of Engineering, Peking University, Beijing 100871 (China); Bakaev, A. [Structural Material Group, Institute of Nuclear Materials Science, SCK-CEN, Mol (Belgium); Duan, Huiling, E-mail: hlduan@pku.edu.cn [State Key Laboratory for Turbulence and Complex System, Department of Mechanics and Engineering Science, College of Engineering, Peking University, Beijing 100871 (China); CAPT, HEDPS and IFSA Collaborative Innovation Center of MoE, Peking University, Beijing 100871 (China)

    2015-11-15

    Crystal plasticity model (CPM) for BCC iron to account for radiation-induced strain softening is proposed. CPM is based on the plastically-driven and thermally-activated removal of dislocation loops. Atomistic simulations are applied to parameterize dislocation-defect interactions. Combining experimental microstructures, defect-hardening/absorption rules from atomistic simulations, and CPM fitted to properties of non-irradiated iron, the model achieves a good agreement with experimental data regarding radiation-induced strain softening and flow stress increase under neutron irradiation. - Highlights: • A stress- and thermal-activated defect absorption model is proposed for the dislocation-loop interaction. • A temperature-dependent plasticity theory is proposed for the irradiation-induced strain softening of irradiated BCC metals. • The numerical results of the model match with the corresponding experimental data.

  6. Solar production of lime; Solare Herstellung von Kalk

    Energy Technology Data Exchange (ETDEWEB)

    Meier, A.; Bonaldi, E.

    2002-07-01

    A novel indirect-heated solar reactor for the solar production of lime (CaO) was designed, built and tested in a solar furnace at the Paul Scherrer Institute PSI, at Villigen, Switzerland. This 10-kW reactor is operated in continuous mode and consists of a tilted rotary kiln with a specially designed high-temperature resistant blackbody absorber made from SiC and a preheating chamber where the small-grained limestone particles are preheated almost to the reaction temperature. The transition to an indirect-heated reactor including additional design changes was successful: (1) With the improved particle feeding system, the maximum CaO production rate was increased from 1.5 kg/hr to about 4 kg/hr. (2) The heat losses were significantly reduced, and consequently the reactor efficiency was increased to more than 30% with a maximum near 35%, while still maintaining a high degree of calcination exceeding 98%. (3) The SiC absorber withstood thermal shocks at temperatures up to 1,600 K. (author)

  7. The Etiology and Treatment of the Softened Phallus after the Radial Forearm Osteocutaneous Free Flap Phalloplasty

    Directory of Open Access Journals (Sweden)

    Seok-Kwun Kim

    2012-07-01

    Full Text Available BackgroundThe radial forearm osteocutaneous free flap is considered to be the standard technique for penile construction. One year after their operation, most patients experience a softened phallus, so that they suffer from difficulties in sexual intercourse. In this report, we present our experience with phalloplasty by radial forearm osteocutaneous free flap, as well as an evaluation of the etiology and treatment of the softened phallus.MethodsBetween March 2005 and February 2010, 58 patients underwent phalloplasty by radial forearm osteocutaneous free flap. Most of their neophallus had been softened subjectively and among them, 12 patients who wanted correction were investigated. We performed repetitive fat injection, artificial dermis grafting, silicone rod insertion, and rib bone with cartilaginous tip graft. Physical examination, plain radiograph, computed tomography, bone scintigraphy, and satisfaction scores were investigated.ResultsMost of the participants' penises have been softened after phalloplasty, and the skin elasticity had been also decreased. On plain radiograph, the distal end of the bone was self-rounded; however, the bone shape of the neophallus had no significant interval changes or resorption. Computed tomography showed equivocal density of cortical bone. On bone scintigraphy, the bone metabolism was active at 3 months postoperatively, and remained active 9 years postoperatively.ConclusionsThe use of a rib bone with cartilaginous tip graft could be an option for improvement of the softened phallus. Silicon rod insertion is also worth considering for rigidity of the softened phallus. Decreased rigidity due to soft tissue atrophy could be alleviated with repeated fat injection and artificial dermis grafting.

  8. Softened food reduces weight loss in the streptozotocin-induced male mouse model of diabetic nephropathy.

    Science.gov (United States)

    Nørgaard, Sisse A; Sand, Fredrik W; Sørensen, Dorte B; Abelson, Klas Sp; Søndergaard, Henrik

    2018-01-01

    The streptozotocin (STZ)-induced diabetic mouse is a widely used model of diabetes and diabetic nephropathy (DN). However, it is a well-known issue that this model is challenged by high weight loss, which despite supportive measures often results in high euthanization rates. To overcome these issues, we hypothesized that supplementing STZ-induced diabetic mice with water-softened chow in addition to normal chow would reduce weight loss, lower the need for supportive treatment, and reduce the number of mice reaching the humane endpoint of 20% weight loss. In a 15 week STZ-induced DN study we demonstrated that diabetic male mice receiving softened chow had reduced acute weight loss following STZ treatment ( p = 0.045) and additionally fewer mice were euthanized due to weight loss. By supplementing the diabetic mice with softened chow, no mice reached 20% weight loss whereas 37.5% of the mice without this supplement reached this humane endpoint ( p = 0.0027). Excretion of corticosterone metabolites in faeces was reduced in diabetic mice on softened chow ( p = 0.0007), suggesting lower levels of general stress. Finally, it was demonstrated that the water-softened chow supplement did not significantly affect the induction of key disease parameters, i.e. %HbA1C and albuminuria nor result in abnormal teeth wear. In conclusion, supplementation of softened food is refining the STZ-induced diabetic mouse model significantly by reducing stress, weight loss and the number of animals sacrificed due to humane endpoints, while maintaining the key phenotypes of diabetes and nephropathy.

  9. Hypersensitive ethylene signaling and ZMdPG1 expression lead to fruit softening and dehiscence.

    Directory of Open Access Journals (Sweden)

    Min Li

    Full Text Available 'Taishanzaoxia' fruit rapid softening and dehiscence during ripening stage and this process is very sensitive to endogenous ethylene. In this study, we cloned five ethylene signal transcription factors (ZMdEIL1, ZMdEIL2, ZMdEIL3, ZMdERF1 and ZMdERF2 and one functional gene, ZMdPG1, encoding polygalacturonase that could loose the cell connection which associated with fruit firmness decrease and fruit dehiscence to illustrate the reasons for this specific fruit phenotypic and physiological changes. Expression analysis showed that ZMdERF1 and ZMdEIL2 transcription were more abundant in 'Taishanzaoxia' softening fruit and dehiscent fruit and their expression was inhibited by an ethylene inhibitor 1-methylcyclopropene. Therefore, ZMdERF1 and ZMdEIL2 expression were responses to endogenous ethylene and associated with fruit softening and dehiscence. ZMdPG1 expression was induced when fruit softening and dehiscence but this induction can be blocked by 1-MCP, indicating that ZMdPG1 was essential for fruit softening and dehiscence and its expression was mediated by the endogenously occurred ethylene. ZMdPG1 overexpression in Arabidopsis led to silique early dehiscence while suppressing ZMdPG1 expression by antisense ZMdPG1 prevented silique naturally opening. The result also suggested that ZMdPG1 related with the connection between cells that contributed to fruit softening and dehiscence. ZMdERF1 was more closely related with ethylene signaling but it was not directly regulated the ZMdPG1, which might be regulated by the synergic pattern of ethylene transcription factors because of both the ZMdERF1 and ZMdERF2 could interact with ZMdEIL2.

  10. Hypoxia-responsive ERFs involved in postdeastringency softening of persimmon fruit.

    Science.gov (United States)

    Wang, Miao-Miao; Zhu, Qing-Gang; Deng, Chu-Li; Luo, Zheng-Rong; Sun, Ning-Jing; Grierson, Donald; Yin, Xue-Ren; Chen, Kun-Song

    2017-11-01

    Removal of astringency by endogenously formed acetaldehyde, achieved by postharvest anaerobic treatment, is of critical importance for many types of persimmon fruit. Although an anaerobic environment accelerates de-astringency, it also has the deleterious effect of promoting excessive softening, reducing shelf life and marketability. Some hypoxia-responsive ethylene response factors (ERFs) participate in anaerobic de-astringency, but their role in accelerated softening was unclear. Undesirable rapid softening induced by high CO 2 (95%) was ameliorated by adding the ethylene inhibitor 1-MCP (1 μL/L), resulting in reduced astringency while maintaining firmness, suggesting that CO 2 -induced softening involves ethylene signalling. Among the hypoxia-responsive genes, expression of eight involved in fruit cell wall metabolism (Dkβ-gal1/4, DkEGase1, DkPE1/2, DkPG1, DkXTH9/10) and three ethylene response factor genes (DkERF8/16/19) showed significant correlations with postdeastringency fruit softening. Dual-luciferase assay indicated that DkERF8/16/19 could trans-activate the DkXTH9 promoter and this interaction was abolished by a mutation introduced into the C-repeat/dehydration-responsive element of the DkXTH9 promoter, supporting the conclusion that these DkERFs bind directly to the DkXTH9 promoter and regulate this gene, which encodes an important cell wall metabolism enzyme. Some hypoxia-responsive ERF genes are involved in deastringency and softening, and this linkage was uncoupled by 1-MCP. Fruit of the Japanese cultivar 'Tonewase' provide a model for altered anaerobic response, as they lost astringency yet maintained firmness after CO 2 treatment without 1-MCP and changes in cell wall enzymes and ERFs did not occur. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  11. Contribution of Drinking Water Softeners to Daily Phosphate Intake in Slovenia

    Directory of Open Access Journals (Sweden)

    Gregor Jereb

    2017-10-01

    Full Text Available The cumulative phosphate intake in a typical daily diet is high and, according to several studies, already exceeds recommended values. The exposure of the general population to phosphorus via drinking water is generally not known. One of the hidden sources of phosphorus in a daily diet is sodium polyphosphate, commonly used as a drinking water softener. In Slovenia, softening of drinking water is carried out exclusively within the internal (household drinking water supply systems to prevent the accumulation of limescale. The aim of the study was to determine the prevalence of sodium phosphates in the drinking water in Slovenia in different types of buildings, to determine residents’ awareness of the presence of chemical softeners in their drinking water, and to provide an exposure assessment on the phosphorus intake from drinking water. In the current study, the presence of phosphates in the samples of drinking water was determined using a spectrophotometric method with ammonium molybdate. In nearly half of the samples, the presence of phosphates as water softeners was confirmed. The measured concentrations varied substantially from 0.2 mg PO4/L to 24.6 mg PO4/L. Nearly 70% of the respondents were not familiar with the exact data on water softening in their buildings. It follows that concentrations of added phosphates should be controlled and the consumers should be informed of the added chemicals in their drinking water. The health risks of using sodium polyphosphate as a drinking water softener have not been sufficiently investigated and assessed. It is highly recommended that proper guidelines and regulations are developed and introduced to protect human health from adverse effects of chemicals in water intended for human consumption.

  12. Contribution of Drinking Water Softeners to Daily Phosphate Intake in Slovenia.

    Science.gov (United States)

    Jereb, Gregor; Poljšak, Borut; Eržen, Ivan

    2017-10-06

    The cumulative phosphate intake in a typical daily diet is high and, according to several studies, already exceeds recommended values. The exposure of the general population to phosphorus via drinking water is generally not known. One of the hidden sources of phosphorus in a daily diet is sodium polyphosphate, commonly used as a drinking water softener. In Slovenia, softening of drinking water is carried out exclusively within the internal (household) drinking water supply systems to prevent the accumulation of limescale. The aim of the study was to determine the prevalence of sodium phosphates in the drinking water in Slovenia in different types of buildings, to determine residents' awareness of the presence of chemical softeners in their drinking water, and to provide an exposure assessment on the phosphorus intake from drinking water. In the current study, the presence of phosphates in the samples of drinking water was determined using a spectrophotometric method with ammonium molybdate. In nearly half of the samples, the presence of phosphates as water softeners was confirmed. The measured concentrations varied substantially from 0.2 mg PO4/L to 24.6 mg PO4/L. Nearly 70% of the respondents were not familiar with the exact data on water softening in their buildings. It follows that concentrations of added phosphates should be controlled and the consumers should be informed of the added chemicals in their drinking water. The health risks of using sodium polyphosphate as a drinking water softener have not been sufficiently investigated and assessed. It is highly recommended that proper guidelines and regulations are developed and introduced to protect human health from adverse effects of chemicals in water intended for human consumption.

  13. Cyclic softening in annealed Zircaloy-2: Role of edge dislocation dipoles and vacancies

    Science.gov (United States)

    Sudhakar Rao, G.; Singh, S. R.; Krsjak, Vladimir; Singh, Vakil

    2018-04-01

    The mechanism of cyclic softening in annealed Zircaloy-2 at low strain amplitudes under strain controlled fatigue at room temperature is rationalized. The unusual softening due to continuous decrease in the phenomenological friction stress is found to be associated with decrease in the resistance against movement of dislocations because of the formation and easy glide of pure edge dislocation dipoles and consequent decrease in friction stress from reduction in the shear modulus. Positron annihilation spectroscopy data strongly support the increase in edge dislocation density containing jogs, from increased positron trapping and increase in annihilation lifetime.

  14. Softening behaviour of brown coal ashes. Influence of ash components and gas atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Hegermann, R; Huettinger, K J [Karlsruhe Univ. (T.H.) (Germany, F.R.). Inst. fuer Chemische Technik

    1990-03-01

    The softening behaviour of brown coal ashes during gasification is important for three reasons: (1) Formation of large agglomerates, (2) inactivation of catalytically active ash components, (3) encapsulation of parts of the coal. The softening behaviour of the ashes was studied with a high temperature dilatometer at ambient pressure in various atmospheres (air, CO{sub 2}, Ar/H{sub 2}O, Ar, H{sub 2}/H{sub 2}O, H{sub 2}) using a push-rod with a conical tip. The heating rate was 5 Kmin{sup -1}, the final temperature 1000deg C, the residence time 1 h. (orig.).

  15. Problems of softening the Chernobyl accident consequences. Proceedings of the International seminar. Pt. 1

    International Nuclear Information System (INIS)

    1993-01-01

    Proceedings of the International seminar on the Problems to soften the Chernobyl accident consequences held by the International Association of Dissemination of Knowledge and the Russian branch of the Society on the Dissemination of Knowledge in Bryansk in 1993. The proceedings of the seminar deal with the study of scientific and practical activity linked with the elimination of the Chernobyl accident effects. Main theoretical concepts used as the basis of the elaborated regulations are presented, as well; ways and techniques to soften the consequences of the Chernobyl accident to decontaminate the affected territories and to protect the population health are discussed

  16. Fatigue hardening and softening studies on strain hardened 18-8 austenitic stainless steel

    International Nuclear Information System (INIS)

    Ramakrishna Prasad, C.; Vasudevan, R.

    1976-01-01

    Metals when subjected to fatigue harden or soften depending on their previous mechanical history. Annealed or mildly cold worked metals are known to harden while severely cold worked metals soften when subjected to fatigue loading. In the present work samples of austenitic 18-8 steel cold worked to 11% and 22% reduction in area were mounted in a vertical pulsator and fatigued in axial tension-compression. Clear cut effects were produced and it was noticed that these depended on the extent of cold work, the amplitude as well as the number of cycles of fatigue and mean stress if any. (orig.) [de

  17. EVALUATION OF BIOAEROSOL COMPONENTS, GENERATION FACTORS, AND AIRBORNE TRANSPORT ASSOCIATED WITH LIME TREATMENT OF CONTAMINATED SEDIMENT

    Science.gov (United States)

    Lime treatment has been used in contaminated sediment management activities for many purposes such as dewatering, improvement of physical properties, and reducing contaminant mobility. Exothermic volatilization of volatile organic compounds from lime-treated sediment is well kno...

  18. Liming Poultry Manures to Kill Pathogens and Decrease Soluble Phosphorus

    International Nuclear Information System (INIS)

    Maguire, R.; Hesterberg, D.; Gernat, A.; Anderson, K.; Wineland, M.; Grimes, J.

    2006-01-01

    Received for publication September 9, 2005. Stabilizing phosphorus (P) in poultry waste to reduce P losses from manured soils is important to protect surface waters, while pathogens in manures are an emerging issue. This study was conducted to evaluate CaO and Ca(OH) 2 for killing manure bacterial populations (pathogens) and stabilizing P in poultry wastes and to investigate the influence on soils following amendment with the treated wastes. Layer manure and broiler litter varying in moisture content were treated with CaO and Ca(OH) 2 at rates of 2.5, 5, 10, and 15% by weight. All treated wastes were analyzed for microbial plate counts, pH, and water-soluble phosphorus (WSP), while a few selected layer manures were analyzed by phosphorus X-ray absorption near edge structure (XANES). A loamy sand and a silt loam were amended with broiler litter and layer manure treated with CaO at rates of 0, 2.5, 5, 10, and 15% and soil WSP and pH were measured at times 1, 8, and 29 d. Liming reduced bacterial populations, with greater rates of lime leading to greater reductions; for example 10% CaO applied to 20% solids broiler litter reduced the plate counts from 793 000 to 6500 mL -1 . Liming also reduced the WSP in the manures by over 90% in all cases where at least 10% CaO was added. Liming the manures also reduced WSP in soils immediately following application and raised soil pH. The liming process used successfully reduced plate counts and concerns about P losses in runoff following land application of these limed products due to decreased WSP

  19. Influence of water-repellent treatment on the properties lime and lime pozzolan mortars

    Directory of Open Access Journals (Sweden)

    Fortes Revilla, C.

    2001-06-01

    Full Text Available The influence that water-repellent products can have on physical and micro-structural properties of lime mortars, and lime plus pozzolan mortars has been studied. Three water repellent products have been used. Mixes of the previously mentioned three water repellents plus a biocide product were also applied. Treatments make the total porosity and saturation coefficient of both mortars to decrease, while colorimetric coordinates bear little alteration. All treatments with water repellent products provided mortars with a hydrophobic property index close to 100%. Durability of such mortars has been also studied: salt crystallization test, frost-thaw and dry-wet cycles, as well as ultraviolet radiation test were carried out. Relationship between mortars behavior and their porosity and saturation coefficient were found.

    En el presente trabajo se ha estudiado la influencia de la aplicación de productos hidrofugantes a morteros de cal y morteros de cal y puzolana sobre sus propiedades físicas y microestructurales. Se han estudiado tres productos hidrofugantes. También han sido estudiados dichos productos junto con un biocida. La porosidad total y el coeficiente de saturación de ambos tipos de morteros se ve reducido por el efecto de los tratamientos mientras que las coordenadas colorimétricas se ven poco alteradas. Todos los tratamientos confieren un índice de hidrofobicidad a los morteros próximo al 100%. Asimismo, también se ha estudiado la durabilidad de dichos morteros frente a la cristalización de sales, hielo-deshielo, los ciclos de humedad-sequedad y radiaciones ultravioleta. Se relaciona el comportamiento de los morteros con su porosidad y el coeficiente de saturación.

  20. Glass-Forming Ability of Soda Lime Borate Liquids

    DEFF Research Database (Denmark)

    Zheng, Qiuju; Mauro, J.C.; Smedskjær, Morten Mattrup

    2012-01-01

    We investigate the composition dependence of glass-forming ability (GFA) of a series of iron-containing soda lime borate liquids by substituting Na2O for B2O3. We have characterized GFA by measuring the glass stability against crystallization using a differential scanning calorimeter (DSC......). The results show that the GFA decreases when substituting Na2O for B2O3. Moreover, we find that there is no direct link between the kinetic fragility and GFA for the soda lime borate series studied herein. We have also discovered and clarified a striking thermal history dependence of the glass stability...

  1. 40 CFR 180.1232 - Lime-sulfur; exemption from the requirement of a tolerance.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Lime-sulfur; exemption from the... Exemptions From Tolerances § 180.1232 Lime-sulfur; exemption from the requirement of a tolerance. An exemption from the requirement of a tolerance is established for residues of lime-sulfur. [70 FR 33363, June...

  2. 40 CFR 180.1231 - Lime; exemption from the requirement of a tolerance.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Lime; exemption from the requirement... From Tolerances § 180.1231 Lime; exemption from the requirement of a tolerance. An exemption from the requirement of a tolerance is established for residues of lime. [70 FR 33363, June 8, 2005] ...

  3. Suitability of a lime source high in manganese as a feed ingredient ...

    African Journals Online (AJOL)

    plasma enzyme levels, mineral concentrations in plasma, faeces and kidneys, mineral content of livers, haematology, hislopathol- ogy of livers and kidneys and bone measurements.It is concluded that the Ouplaas lime, .... Table 1 Mineral composition of the pure lime sources (dry basis). Lime sources. Na. (vo). Mg. (vo). K.

  4. Bacterial Colonization of Pellet Softening Reactors Used during Drinking Water Treatment

    NARCIS (Netherlands)

    Hammes, F.; Boon, N.; Vital, M.; Ross, P.; Magic-Knezev, A.; Dignum, M.

    2010-01-01

    Pellet softening reactors are used in centralized and decentralized drinking water treatment plants for the removal of calcium (hardness) through chemically induced precipitation of calcite. This is accomplished in fluidized pellet reactors, where a strong base is added to the influent to increase

  5. Effects Of Various Parameters On The Thickening Of Softening Plant Sludges

    DEFF Research Database (Denmark)

    Peters, Günther H.J.; Baumann, E. R.; Larson, M. A.

    1989-01-01

    Spectroscopic and thermal data for sludges from full-scale softening plants showed calcium and magnesium precipitated as calcite and an amorphous hydrated hydroxide, respectively. Magnesium ions were not incorporated into the calcium lattice to form a magnesian calcite. Scanning electron...

  6. A new constitutive equation for strain hardening and softening of fcc metals during severe plastic deformation

    International Nuclear Information System (INIS)

    Wei, W.; Wei, K.X.; Fan, G.J.

    2008-01-01

    The stress-strain relationship for strain hardening and softening of high-purity aluminum and copper, which were deformed by equal channel angular pressing (ECAP) at ambient temperature, was analyzed by combining the Estrin and Mecking (EM) model and an Avrami-type equation with experimental data during severe plastic deformation. The initial strain hardening can be described by the EM model, while the flow stress arrives at the peak stress after it was saturated. However, strain softening similar to plastic deformation at high temperatures is observed after the peak stress. Moreover, the peak strain at the maximum flow stress is ∼4 for copper and ∼2 for aluminum. A new constitutive equation was developed to describe strain softening at high strain levels, which was supported well by tensile, compression and microhardness tests at room temperature and low strain rate. It was observed that dynamic recovery and recrystallization occurs in copper, and recrystallized grains and their growth in aluminum. The results indicate that dynamic recovery and recrystallization was the dominant softening mechanism, which was confirmed by scanning electron microscopy-electron channeling contrast observations and the abnormal relationship between the imposed strain during ECAP and subsequent recrystallization temperature after ECAP

  7. Bio-softening of mature coconut husk for facile coir recovery.

    Science.gov (United States)

    Suganya, D S; Pradeep, S; Jayapriya, J; Subramanian, S

    2007-06-01

    Bio-softening of the mature coconut husk using Basidiomyceteous fungi was attempted to recover the soft and whiter fibers. The process was faster and more efficient in degrading lignin and toxic phenolics. Phanerochaete chrysosporium, Pleurotus eryngii and Ceriporiopsis subvermispora were found to degrade lignin efficiently without any appreciable loss of cellulose, yielding good quality fiber ideal for dyeing.

  8. Finite strain logarithmic hyperelasto-plasticity with softening: a strongly non-local implicit gradient framework

    NARCIS (Netherlands)

    Geers, M.G.D.

    2004-01-01

    This paper addresses the extension of a Eulerian logarithmic finite strain hyperelasto-plasticity model in order to incorporate an isotropic plastic damage variable that leads to softening and failure of the plastic material. It is shown that a logarithmic elasto-plastic model with a strongly

  9. The Value of Fighting Irreversible Demise by Softening the Irreversible Cost

    NARCIS (Netherlands)

    Magis, P.; Sbuelz, A.

    2005-01-01

    We study a novel issue in the real-options-based technology innovation literature by means of double barrier contingent claims analysis.We show how much a ¯rm with the monopoly over a project is willing to spend in investment technology innovation that softens the irreversible cost of accessing the

  10. Phases of fracture process zone and tension softening properties of concrete

    International Nuclear Information System (INIS)

    Mihashi, H.; Nomura, N.

    1991-01-01

    The safety and serviceability of concrete structures are influenced very much by the cracking behavior of concrete. Since comprehensive numerical analysis techniques have been extensively developed to predict the mechanical behavior of concrete structures in the limit state, it is essential to study the constitutive laws to describe the cracking behavior of concrete in detail. The tension softening behavior of concrete is highly dominated by the existence of a fracture process zone (FPZ) ahead of a crack tip. Since the direct observation of the FPZ of concrete is hardly possible, the indirect techniques are applied, but it is still ambiguous what happens in the FPZ and how it affects the tension softening property. The purpose of this study is to present the property of the FPZ focusing on the influence of material structures by means of three-dimensional acoustic emission. These results are correlated to tension softening behavior evaluated by a numerical analysis to discuss how the tension softening property is related to the characteristics of the FPZ. The test procedure and the results are reported. (K.I.)

  11. Production, use and reuse of Dutch calcite in drinking water pellet softening

    NARCIS (Netherlands)

    Palmen, LJ; Schetters, M.J.A.; van der Hoek, J.P.; Kramer, O.J.I.; Kors, L.J.; Hofs, B; Koppers, H

    2014-01-01

    In The Netherlands, 50% of the drinking water is treated with pellet softening for various reasons: i) public health (heavy metal solubility), ii) costs (warm water device maintenance, energy and soap requirement), iii) environmental benefits (energy and soap requirement) and iv) customer comfort

  12. Identification of Differentially Expressed Genes Associated with Apple Fruit Ripening and Softening by Suppression Subtractive Hybridization.

    Science.gov (United States)

    Zhang, Zongying; Jiang, Shenghui; Wang, Nan; Li, Min; Ji, Xiaohao; Sun, Shasha; Liu, Jingxuan; Wang, Deyun; Xu, Haifeng; Qi, Sumin; Wu, Shujing; Fei, Zhangjun; Feng, Shouqian; Chen, Xuesen

    2015-01-01

    Apple is one of the most economically important horticultural fruit crops worldwide. It is critical to gain insights into fruit ripening and softening to improve apple fruit quality and extend shelf life. In this study, forward and reverse suppression subtractive hybridization libraries were generated from 'Taishanzaoxia' apple fruits sampled around the ethylene climacteric to isolate ripening- and softening-related genes. A set of 648 unigenes were derived from sequence alignment and cluster assembly of 918 expressed sequence tags. According to gene ontology functional classification, 390 out of 443 unigenes (88%) were assigned to the biological process category, 356 unigenes (80%) were classified in the molecular function category, and 381 unigenes (86%) were allocated to the cellular component category. A total of 26 unigenes differentially expressed during fruit development period were analyzed by quantitative RT-PCR. These genes were involved in cell wall modification, anthocyanin biosynthesis, aroma production, stress response, metabolism, transcription, or were non-annotated. Some genes associated with cell wall modification, anthocyanin biosynthesis and aroma production were up-regulated and significantly correlated with ethylene production, suggesting that fruit texture, coloration and aroma may be regulated by ethylene in 'Taishanzaoxia'. Some of the identified unigenes associated with fruit ripening and softening have not been characterized in public databases. The results contribute to an improved characterization of changes in gene expression during apple fruit ripening and softening.

  13. Drainage, liming and fertilization of organic soils. 1. Long-term effects on acid/base relations

    International Nuclear Information System (INIS)

    Braekke, F.H.

    1999-01-01

    Long-term changes of the acid/base relations of organic soils after drainage, fertilization and/or liming at three experimental sites - two ombrogenous and one soligenous - in south-central Norway are discussed. These sites were drained, fertilized and/or limed in 1953-1956 and sampled in 1991-1992. Drainage at the ombrogenous sites caused: insignificant shifts of pH, higher bulk densities to 40 cm depth, higher ash percentage, higher contents of N and P to 20 cm depth and reduced concentrations of total Ca, K, Mg, Na, Al and Fe in soil layers deeper than 20 cm. The soligenous site was not effectively drained; despite this, pH dropped about 0.5 unit in the surface and subsurface soil layers of the control plots, while small changes were measured for most other soil variables. The suggested reason for the pH drop is limited sulphide oxidation in the upper 20 cm drained layer. Base saturation at actual soil pH, when all treatments were included, was estimated with good precision by four regressors: pH, extractable Al, extractable Fe and extractable Ca (R 2 = 0.90-0.95). Similar models explained 97-99% of the variation in base saturation at soil pH = 7.0. The lime effects at the properly drained oligotrophic sites were proportional to applied doses; for pH to 40 cm, base saturation to 60 cm, and Ca concentration to 60 cm depth. At the less well-drained soligenous site, effects were limited to the upper 30 cm layer. Both drainage and liming caused higher cation exchange capacities and proper drainage seems to be a prerequisite for the liming effect. Estimated recovery of calcium to 60 cm depth was 64-79% at the ombrogenous sites and 42-46% at the soligenous site 28 refs, 3 figs, 8 tabs

  14. Influence of Hydrated Lime on the Properties and Permanent Deformation of the Asphalt Concrete Layers in Pavement

    Directory of Open Access Journals (Sweden)

    Al-Tameemi Ahmed F.

    2015-07-01

    Full Text Available Flexible or asphalt concrete pavement is the paving system most widely adopted all over the world. It has been recognized that there are many different types of the factors affecting the performance and durability of asphalt concrete pavement, including the service conditions, such as: the variation of temperature from mild to extremes and the repeated excessive axle loading as well as the inadequate quality of the raw materials. All of these when combined together are going to accelerate the occurrence of distresses in flexible pavement such as permanent deformation and fatigue cracking. As the result, there has an urgent need to enhance the ability of asphalt concrete mixture to resist distresses happened in pavement. Use of additives is one of the techniques adopted to improve pavement properties. It has been found that hydrated lime might be one of the effective additives because it is widely available and relatively cheap compared to other modifiers like polymers. This paper presents an experimental study of the hydrated-lime modified asphalt concrete mixtures. Five different percentages of the hydrated lime additive were investigated, namely (1, 1.5, 2, 2.5 and 3 percent. The hydrated lime additive was used as partial replacement of limestone filler by total weight of the aggregate. The designed Hot Mix Asphalt (HMA concretes are for the application of three pavement courses, i.e. Surface, Leveling and Base. These mixtures are designed and tested following Marshall procedure and uniaxial repeated loading to evaluate permanent deformation at different temperatures of 20°C, 40°C and 60°C. The experimental results show that the addition of hydrated lime as a partial replacement of ordinary limestone mineral filler results a significant improvement on mechanical properties and the resistant to permanent deformation of the designed asphalt concrete mixtures.

  15. The effect of hardening laws and thermal softening on modeling residual stresses in FSW of aluminum alloy 2024-T3

    DEFF Research Database (Denmark)

    Sonne, Mads Rostgaard; Tutum, Cem Celal; Hattel, Jesper Henri

    2013-01-01

    or kinematic hardening together with the metallurgical softening model were applied in order to give a first impression of the tendencies in residual stresses in friction stir welds when choosing different hardening and softening behaviors. Secondly, real friction stir butt welding of aluminum alloy 2024-T3...

  16. Numerical modeling of AA2024-T3 friction stir welding process for residual stress evaluation, including softening effects

    DEFF Research Database (Denmark)

    Sonne, Mads Rostgaard; Carlone, Pierpaolo; Palazzo, Gaetano S.

    2014-01-01

    In the present paper, a numerical finite element model of the precipitation hardenable AA2024-T3 aluminum alloy, consisting of a heat transfer analysis based on the Thermal Pseudo Mechanical model for heat generation, and a sequentially coupled quasi-static stress analysis is proposed. Metallurgi...

  17. Radiation dose measurement by electron spin resonance studies of tooth enamel in lime and non-lime consuming individuals from the Silchar region of northeast India

    International Nuclear Information System (INIS)

    Bhattacharjee, Deborshi; Zhumadilov, Kassym; Bhattacharyya, Joyeeta; Hoshi, Masaharu; Ivannikov, Alexander I.; Stepanenko, Valeriy F.; Tanaka, Kenichi; Endo, Satoru; Ohtaki, Megu; Toyoda, Shin

    2009-01-01

    Electron spin resonance (ESR) dosimetry of teeth is used extensively for dose estimation following exposure to radiation. The population inhabiting the northeast region of India is prone to different cancers of the head and neck, and their prevalence is several times the national average. The objective of this study was to determine the role of radiation in the causation of this high cancer incidence by performing ESR spectroscopic measurements of tooth samples collected from the general population living in and around the city of Silchar. Nineteen tooth samples were used, and the age of the patients was 13-60 years. The excess dose, determined by subtraction of the natural background dose from the dose absorbed by the enamel, was found to the extent of 123±43 mGy. However, the individual excess dose was found to be higher in subjects who consumed lime (5/6) than in non-lime-consuming subjects (2/13). It is not entirely clear if radiation is the cause of this excess cancer in this region of India. Therefore there is a need for wider studies including consideration of tobacco consumption as well as a larger number of samples for tooth enamel dosimetry. (author)

  18. Laboratory-scale simulations with hydrated lime and organic ...

    African Journals Online (AJOL)

    Laboratory-scale simulations with hydrated lime and organic polymer to evaluate the effect of pre-chlorination on motile Ceratium hirundinella cells during ... When organic material is released from algal cells as a result of physical-chemical impacts on the cells, it may result in tasteand odour-related problems or the ...

  19. Study of Hydrated Lime in Environmental Scanning Electron Microscopy

    Czech Academy of Sciences Publication Activity Database

    Tihlaříková, Eva; Neděla, Vilém; Rovnaníková, P.

    2013-01-01

    Roč. 19, S2 (2013), s. 1644-1645 ISSN 1431-9276 R&D Projects: GA ČR GAP102/10/1410; GA MŠk ED0017/01/01 Institutional support: RVO:68081731 Keywords : Hydrated Lime * Environmental Scanning Electron Microscopy Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.757, year: 2013

  20. Simulation of the self-healing of dolomitic lime mortar

    NARCIS (Netherlands)

    Lubelli, B.; Nijland, T.G.; Hees, R.P.J. van

    2012-01-01

    A test procedure was set up to reproduce laboratory self-healing on lime-based (both pure calcium and magnesium-calcium) mortar specimens. After a few months of testing, during which time the specimens were submitted to wet-dry cycles, thin sections of the specimens were prepared and observed using

  1. K'qizaghetnu Ht'ana (Stories from Lime Village).

    Science.gov (United States)

    Bobby, Pete; And Others

    A cross section of Athabascan life as related by eight inhabitants of Lime Village, Alaska, is given in this document. The short narratives are printed in English and in Dena'ina. Illustrations accompany the text. The stories tell of making eagle feather robes, birchbark or mooseskin boats, a raincoat from black bear intestines, and boots from…

  2. EFFECTS OF LIME (CAO) ON THE ENDOTOXIN LEVELS OF BIOSOLIDS

    Science.gov (United States)

    Lime addition is a common practice for treating biosolids in order to meet EPA 503 requirements for land application. Since this treatment kills the majority of microorganisms, will it increase the level of endotoxins present in biosolids? And, if endotoxin levels are increased, ...

  3. Simulation of self-healing of dolomitic lime mortar

    NARCIS (Netherlands)

    Lubelli, B.; Nijland, T.G.; Van Hees, R.P.J.

    2011-01-01

    In the present research a test procedure was set up to reproduce self-healing on lime-based (both pure calcium and magnesium-calcium) mortar specimens in laboratory. After few months testing, during which the specimens were subjected to wet-dry cycles, thin sections of the specimens were prepared

  4. Incorporation of turmeric-lime mixture during the preparation of ...

    African Journals Online (AJOL)

    New types of tomato puree products were developed by blanching matured tomatoes (Lycopersicon esculentum) for 1 min, 2 min and 3 min individually with or without addition of the mixture of turmeric and lime during the blanching time. Soluble solid content and pH of the puree products were in therange of 11 - 12.6 Brix ...

  5. Fluoride removal performance of phosphoric acid treated lime ...

    African Journals Online (AJOL)

    Fluoride in drinking water above permissible levels is responsible for dental and skeletal fluorosis. In this study, removal of fluoride ions from water using phosphoric acid treated lime was investigated in continuous and point-of-use system operations. In the continuous column operations, fluoride removal performance was ...

  6. Effect of quick lime on physicochemical properties of clay soil

    Directory of Open Access Journals (Sweden)

    Bessaim Mohammed Mustapha

    2018-01-01

    Full Text Available Clay soils are known for their water sensitivity, which causes irreparable damage to any structure built on this type of soil. In order to avoid such problem, it is necessary to use various improvement and stabilization methods such as treatment with lime. This process has been used successfully in the field for decades. The addition of lime generates various physicochemical reactions within the soil such as cation exchange and pozzolanic reactions which are largely responsible for the improvement of the soil in question. This paper presents a study concerning the variation of physicochemical properties of clayey soil with the addition of quicklime at different percentages. Experiments were performed on two clayey soils (CL type in order to investigate the influence of quicklime on Atterberg limits and pH. These tests were carried out in an attempt to study and follow the development and progression of various reactions occurred within the soil with various lime percentages. The results show that the addition of quicklime causes a significant improvement in soil properties by reducing plasticity and thereby improves the soil workability. It can also be found that the addition of lime increase pH of soil, which allow activating pozzolanic reactions who tend to stabilize the soil in question by formation of cementitious compounds. Finally, the pH can be considered as a relevant parameter who allows a better understanding of the reactions that occur in the soil matrix.

  7. The Chemical Composition of Different Sources of Liming Materials ...

    African Journals Online (AJOL)

    An incubation experiment was conducted to evaluate the effect of some liming materials on soil chemical properties. The treatments comprised Cocoa Husk Pod Ash (CPHA), Oyster Shell Ash (OSA), Palm Bunch Ash (PBA), Calcium Carbonate (CaCO3), Kitchen Residues Ash (KRA) and Saw Dust Ash (SDA) at five levels ...

  8. Dental erosion due to lime consumption; review of literature and ...

    African Journals Online (AJOL)

    Background: Dental health is increasingly threatened by dental erosion introduced by today's lifestyle. Extrinsic factor is the most implicated. Few literatures mentioned lime-incited dental erosion. Case Description: A 49 year old woman was referred to our clinic with tooth wear and sensitivity. She was in good health but on ...

  9. Effect of gamma radiation on chemical composition and storability of lime RTS

    International Nuclear Information System (INIS)

    Pandey, S.K.; Bisen, A.; Dwivedi, V.

    2008-01-01

    In the present investigation, the RTS was irradiated with different doses of gamma radiation to study their effect on chemical composition and storability of lime RTS and vitamin C content only was influenced significantly by 50 Gy gamma radiation during storage (16 days) without adversely affecting the quality of lime fruits, whereas, under control and higher doses of gamma radiation, the quality of lime RTS was deteriorated. The irradiation of lime with 50 Gy gamma radiation may be useful for extending storability of lime of RTS and stabilizing the market demand. (author)

  10. A multicentre randomised controlled trial and economic evaluation of ion-exchange water softeners for the treatment of eczema in children:the Softened Water Eczema Trial (SWET)

    OpenAIRE

    Thomas, K. S.; Koller, K.; Dean, Tara; O'Leary, C. J.; Sach, T. H.; Frost, A.; Pallett, I.; Crook, A. M.; Meredith, S.; Nunn, A. J.; Burrows, N.; Pollock, I.; Graham-Brown, R.; O'Toole, E.; Potter, D.

    2011-01-01

    Objectives: To determine whether installation of an ion-exchange water softener in the home could improve atopic eczema in children and, if so, to establish its likely cost and cost-effectiveness. Design: An observer-blind, parallel-group randomised controlled trial of 12 weeks duration followed by a 4-week observational period. Eczema was assessed by research nurses blinded to intervention at baseline, 4 weeks, 12 weeks and 16 weeks. The primary outcome was analysed as intent-to-treat, using...

  11. A plane stress softening plasticity model for orthotropic materials

    NARCIS (Netherlands)

    Lourenço, P.B.; Borst, R. de; Rots, J.G.

    1997-01-01

    A plane stress model has been developed for quasi-brittle orthotropic materials. The theory of plasticity, which is adopted to describe the inelastic behaviour, utilizes modern algorithmic concepts, including an implicit Euler backward return mapping scheme, a local Newton-Raphson method and a

  12. Effect of liquid liming on sorghum growth in an Ultisol.

    Directory of Open Access Journals (Sweden)

    Manuel E. Camacho

    2015-06-01

    Full Text Available   The aim of this study was to evaluate the effects of the application of liquid lime on sorghum growth in an Ultisol. This research was conducted between August and November, 2011 at the Agricultural Research Center, San José, Costa Rica. In an Ultisol planted with sorghum, in pots of 800 ml, the following treatments where applied: control without lime, calcium carbonate at doses of 10 and 20 l/ha, magnesium oxide at doses of 10 and 20 l/ha, calcium carbonate + magnesium oxide at doses of 5 + 5 and 10 + 10 l/ha, respectively. Six weeks after planting, sorghum was harvested, measuring leaf area, dry and fresh weight of the aerial and root biomass, nutrient absorption and the soil chemical characteristics. Treatments using calcium carbonate and calcium carbonate + magnesium oxide obtained the best values of leaf area and the higher weight of the aerial and root biomass of sorghum. Even though there were no significant differences between liquid lime treatments, there were regarding control without lime and weight biomass variables. Liquid calcium carbonate significantly increased Ca absorption, and the calcium carbonate + magnesium oxide treatment at doses of 10 l/h showed the highest Mg absorption. All amendment treatments caused an improvement of the soil fertility, the most notable being the application of 20 l/ha of magnesium oxide that dropped the exchangeable acidity from 9.02 to 0.36 cmol(+/l, acidity saturation dropped from 95 to 3.3%, and pH increased from 5 to 5.7. It was concluded that the liquid liming amendments had a positive effect over the crop and the soil fertility.

  13. The relationships among lemons, limes and citron: a chromosomal comparison.

    Science.gov (United States)

    Carvalho, R; Soares Filho, W S; Brasileiro-Vidal, A C; Guerra, M

    2005-01-01

    Lemons, limes and citron constitute a group of closely related Citrus species, whose species delimitations and taxonomic relationships are unclear. In order to identify karyotypic similarities and species relationships within this group, the CMA+/DAPI- banding pattern and the distribution of the 5S and 45S rDNA sites of 10 accessions of lime, lemon, and citron were investigated. The four cultivars of C. limon analyzed showed the same pattern of CMA+ bands and rDNA sites, suggesting that they originated from a single germplasm, later differentiated by distinct somatic mutations. The lemons C. jambhiri, C. limonia and C. volkameriana displayed karyotypes very similar to each other, but they differed from C. limon by the absence of a single chromosome with one band in each telomere. The limes, C. aurantifolia and C. limettioides, seemed less related to each other and exhibited different heteromorphic chromosome pairs. In C. aurantifolia, the presence of a chromosome type unknown in all other Citrus species cytologically known so far supports the assumption that this accession may be derived from a hybrid with a species from the subgenus Papeda or from another genus. Citrus medica was the only homozygous accession of this group and all of its chromosome types were clearly represented in limes and lemons, some of them forming heteromorphic pairs. The analysis of the distribution of rDNA sites allowed a further refinement of the comparison among accessions. The lemons and limes were heterozygous for all rDNA sites, whereas C. medica was entirely homozygous. These data support the hypothesis that C. medica is a true species while the other nine accessions are hybrids. Copyright 2005 S. Karger AG, Basel.

  14. New waste based clinkers: Belite and lime formulations

    International Nuclear Information System (INIS)

    Raupp-Pereira, Fabiano; Ball, Richard James; Rocha, Joao; Labrincha, Joao A.; Allen, Geoffrey C.

    2008-01-01

    This work describes the formulation of new belite-based (CR2) and lime-based (CR3) cementitious materials derived from industrial wastes, such as sludges (generated in the Al-anodising and surface coating industrial processes, potable water filtration/cleaning operations and in marble sawing processes) and foundry sand. Powder mixtures were prepared and fired at different temperatures. For comparison, similar formulations were prepared with pre-treated and commercially available natural raw materials and processed in similar conditions. The thermal process was followed by differential scanning calorimetry (DSC) and high-temperature powder X-ray diffraction (HT-XRD) studies. The CR2 clinker was found to contain belite as the main cementitious phase, the main polymorph being identified by NMR. The CR3 clinker contained common cementitious phases, such as C 3 A and C 3 S, but free lime and calcium aluminium oxide sulphates were also identified by high temperature XRD and NMR. Then the corresponding cement was prepared and the evolution of the mechanical strength with time was evaluated. The lime-based cement obtained from wastes shows a stronger hardening character than the standard material, which tends to show dusting phenomena due to the presence of a reasonable amount of free lime (as the result of its expansive reaction with ambient moisture). Some fluxing impurities (e.g. alkalis) present in the waste materials improve the overall reactivity of the mixture and induces the combination of the lime in CR3. Raman, XPS and FIB techniques were used to fully characterise the aged cements

  15. Classical Methods and Calculation Algorithms for Determining Lime Requirements

    Directory of Open Access Journals (Sweden)

    André Guarçoni

    Full Text Available ABSTRACT The methods developed for determination of lime requirements (LR are based on widely accepted principles. However, the formulas used for calculation have evolved little over recent decades, and in some cases there are indications of their inadequacy. The aim of this study was to compare the lime requirements calculated by three classic formulas and three algorithms, defining those most appropriate for supplying Ca and Mg to coffee plants and the smaller possibility of causing overliming. The database used contained 600 soil samples, which were collected in coffee plantings. The LR was estimated by the methods of base saturation, neutralization of Al3+, and elevation of Ca2+ and Mg2+ contents (two formulas and by the three calculation algorithms. Averages of the lime requirements were compared, determining the frequency distribution of the 600 lime requirements (LR estimated through each calculation method. In soils with low cation exchange capacity at pH 7, the base saturation method may fail to adequately supply the plants with Ca and Mg in many situations, while the method of Al3+ neutralization and elevation of Ca2+ and Mg2+ contents can result in the calculation of application rates that will increase the pH above the suitable range. Among the methods studied for calculating lime requirements, the algorithm that predicts reaching a defined base saturation, with adequate Ca and Mg supply and the maximum application rate limited to the H+Al value, proved to be the most efficient calculation method, and it can be recommended for use in numerous crops conditions.

  16. Dewaterability of five sewage sludges in Guangzhou conditioned with Fenton's reagent/lime and pilot-scale experiments using ultrahigh pressure filtration system.

    Science.gov (United States)

    Liang, Jialin; Huang, Shaosong; Dai, Yongkang; Li, Lei; Sun, Shuiyu

    2015-11-01

    Sludge conditioning with Fenton's reagent and lime is a valid method for sludge dewatering. This study investigated the influence of different organic matter content sludge on sludge dewatering and discussed the main mechanism of sludge conditioning by combined Fenton's reagent and lime. The results indicated that the specific resistance to filterability (SRF) of sludge was reduced efficiently by approximately 90%, when conditioned with Fenton's reagent and lime. Through single factor experiments, the optimal conditioning combinations were found. In addition, the relationship between VSS% and consumption of the reagents was detected. Furthermore, it was also demonstrated that the SRF and filtrate TOC values had a significant correlation with VSS% of sludge (including raw and conditioned). The main mechanism of sludge dewatering was also investigated. Firstly, it revealed that the dewaterability of sludge was closely correlated to extracellular polymeric substances (EPS) and bound water contents. Secondly, the results of scanning electron microscopy (SEM) stated that sludge particles were to be smaller and thinner after conditioning. And this structure could easily form outflow channels for releasing free water. Additionally, with the ultrahigh pressure filtration system, the water content of sludge cake conditioned with Fenton's reagent and lime could be reduced to below 50%. Moreover, the economic assessment shows that Fenton's reagent and lime combined with ultrahigh pressure filtration system can be an economical and viable technology for sewage sludge dewatering. Finally, three types of sludge were classified: (1) Fast to dewater; (2) Moderately fast to dewater; (3) Slow to dewater sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. [Study on Archaeological Lime Powders from Taosi and Yinxu Sites by FTIR].

    Science.gov (United States)

    Wei, Guo-feng; Zhang, Chen; Chen, Guo-liang; He, Yu-ling; Gao, Jiang-tao; Zhang, Bing-jian

    2015-03-01

    Archaeological lime powders samples from Taosi and Yinxu sites, natural limestone and experimentally prepared lime mortar were investigated by means of Fourier transform infrared spectrometry (FTIR) to identify the raw material of lime powders from Taosi and Yinxu sites. Results show that ν2/ν4 ratio of calcite resulted from carbonation reaction of man-made lime is around 6.31, which is higher than that of calcite in natural limestone and reflects the difference in the disorder of calcite crystal structure among the natural limestone and prepared lime mortar. With additional grinding, the values of v2 and ν4 in natural limestone and prepared lime mortar decrease. Meanwhile, the trend lines of ν2 versus ν4 for calcite in experimentally prepared lime mortar have a steeper slope when compared to calcite in natural limestone. These imply that ν2/ν4 ratio and the slope of the trend lines of ν2 versus ν4 can be used to determine the archaeological man-made lime. Based on the experiment results, it is possible that the archaeological lime powder from Taosi and Yinxu sites was prepared using man-made lime and the ancient Chinese have mastered the calcining technology of man-made lime in the late Neolithic period about 4 300 years ago.

  18. LIME: 3D visualisation and interpretation of virtual geoscience models

    Science.gov (United States)

    Buckley, Simon; Ringdal, Kari; Dolva, Benjamin; Naumann, Nicole; Kurz, Tobias

    2017-04-01

    Three-dimensional and photorealistic acquisition of surface topography, using methods such as laser scanning and photogrammetry, has become widespread across the geosciences over the last decade. With recent innovations in photogrammetric processing software, robust and automated data capture hardware, and novel sensor platforms, including unmanned aerial vehicles, obtaining 3D representations of exposed topography has never been easier. In addition to 3D datasets, fusion of surface geometry with imaging sensors, such as multi/hyperspectral, thermal and ground-based InSAR, and geophysical methods, create novel and highly visual datasets that provide a fundamental spatial framework to address open geoscience research questions. Although data capture and processing routines are becoming well-established and widely reported in the scientific literature, challenges remain related to the analysis, co-visualisation and presentation of 3D photorealistic models, especially for new users (e.g. students and scientists new to geomatics methods). Interpretation and measurement is essential for quantitative analysis of 3D datasets, and qualitative methods are valuable for presentation purposes, for planning and in education. Motivated by this background, the current contribution presents LIME, a lightweight and high performance 3D software for interpreting and co-visualising 3D models and related image data in geoscience applications. The software focuses on novel data integration and visualisation of 3D topography with image sources such as hyperspectral imagery, logs and interpretation panels, geophysical datasets and georeferenced maps and images. High quality visual output can be generated for dissemination purposes, to aid researchers with communication of their research results. The background of the software is described and case studies from outcrop geology, in hyperspectral mineral mapping and geophysical-geospatial data integration are used to showcase the novel

  19. Wood ash and lime. Effects on uptake of nutrients and heavy metals in bilberries

    International Nuclear Information System (INIS)

    Nilsson, Torbjoern; Eriksson, H.M.

    1998-01-01

    Ten km north of Uppsala in eastern Sweden a field plot (2x2 m) experiment, with different ash and lime treatments, was established in June 1993 in a 70-year old mixed stand of Norway spruce and Scots pine on a sandy soil. The experiment included twelve treatments and one control, all with four replicates. The treatments were; a well-combusted loose wood ash, well-hardened ash granules, hardened and then crushed and sieved mixed ash, a mixture of hardened ash and lime, hardened wood ash and finally, lime. The normal dose was 4 tons per hectare. Two and thirteen months after treatment, bilberries were sampled. Bilberries sampled two months after treatment were analyzed for Ca, Mg, K, P, Al, Mn, Cd, Cu, Pb and Zn for nine treatments. Two months after treatment, the variation in the contents of different elements was very large, especially for K, P, Mn and Zn. Bilberries in the control had, on an average, lower contents of Ca, Mg, K and Cu than bilberries from the treated plots. Contents of Zn and Cd were, on an average, highest in the control plots. However, no significant differences between treatments were found. Thirteen months after treatment, the variation in content of all the heavy metals analyzed had decreased as well as the content of Pb and Zn. However, the contents of Cd and Cu had increased somewhat. No significant differences between treatments were found. It was concluded that the different treatments had a negligible effect on the content of heavy metals in bilberries the first year after treatment 122 refs, 10 figs, 15 tabs

  20. Gasification of tall oil soap for lime kiln fuel. Suovan kaasutus meesauunin polttoaineeksi

    Energy Technology Data Exchange (ETDEWEB)

    Saviharju, K.; McKeough, P.; Pyykkoenen, M.; Oasmaa, A. (Technical Research Centre of Finland, Espoo (Finland). Lab. of Fuel and Process Technology)

    1993-01-01

    The energy delivered to a modern pulp mill in the form of material unsuitable for fibre production exceeds the energy demand of the mill by about 30 %. Purchased lime kiln fuel further increases the surplus by 5-10 %. On the other hand, acidulation of tall oil soap adds about 1-3 kg SO[sub 2] for t of pulp onto the difficult-to-manage sulphur balance of the mill. Pyrolysis or gasification of tall oil soap could alleviate both these problems. In this study, gasification of tall oil soap was investigated in laboratory experiments as well as on a 200 kW test gasifier. In the laboratory experiments tall oil soap was pyrolyzed both on a heated-grid unit and on a thermobalance at heating rates of 600 K/s and 10 K/min, respectively. The maximum temperature was 675 deg C. The amount of volatiles formed was high, about 77 %, the amount of coke and inorganic salts being 7 % and 16 %, respectively. In the 200 kW gasifier, tests were carried out with mixed soap (pine and birch) such that the gas outlet temperature was 680-690 deg C. Because of the low gasification temperature complete gasification of the char was not achieved. The heat content of the product gas, including the sensible heat, was about 5.8 MJ/m[sup 3]n, which was estimated to be sufficient for lime calcination. Typical of the product gas were high tar content (20 g/m[sup 3]n), high acetylene content, and the absence of hydrogen sulphide. Overall, the results of this study indicated that the most significant subjects for future research are the atomization properties of tall oil soap, the effects of different amounts of input sodium on the operability of the lime kiln, and the economics of the proposed gasification process

  1. Influence of curing rate on softening in ethanol, degree of conversion, and wear of resin composite

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Peutzfeldt, Anne; Asmussen, Erik

    2011-01-01

    PURPOSE: To investigate the effect of curing rate on softening in ethanol, degree of conversion, and wear of resin composites. METHOD: With a given energy density and for each of two different light-curing units (QTH or LED), the curing rate was reduced by modulating the curing mode. Thus......, the irradiation of resin composite specimens (Filtek Z250, Tetric Ceram, Esthet-X) was performed in a continuous curing mode and in a pulse-delay curing mode. Wallace hardness was used to determine the softening of resin composite after storage in ethanol. Degree of conversion was determined by infrared...... exposed to the pulse-delay curing mode were softer than resin composites exposed to continuous cure (Pconversion (P

  2. Brine reuse in ion-exchange softening: salt discharge, hardness leakage, and capacity tradeoffs.

    Science.gov (United States)

    Flodman, Hunter R; Dvorak, Bruce I

    2012-06-01

    Ion-exchange water softening results in the discharge of excess sodium chloride to the aquatic environment during the regeneration cycle. In order to reduce sodium chloride use and subsequent discharge from ion-exchange processes, either brine reclaim operations can be implemented or salt application during regeneration can be reduced. Both result in tradeoffs related to loss of bed volumes treated per cycle and increased hardness leakage. An experimentally validated model was used to compare concurrent water softening operations at various salt application quantities with and without the direct reuse of waste brine for treated tap water of typical midwestern water quality. Both approaches were able to reduce salt use and subsequent discharge. Reducing salt use and discharge by lowering the salt application rate during regeneration consequently increased hardness leakage and decreased treatment capacity. Single or two tank brine recycling systems are capable of reducing salt use and discharge without increasing hardness leakage, although treatment capacity is reduced.

  3. Acoustic softening in metals during ultrasonic assisted deformation via CP-FEM

    KAUST Repository

    Siddiq, Amir

    2011-01-01

    In this paper, a phenomenological crystal plasticity model is modified to account for acoustic (ultrasonic) softening effects based on the level of ultrasonic intensity supplied to single and polycrystalline metals. The material parameters are identified using the inverse modeling approach by interfacing the crystal plasticity model with an optimization tool. The proposed model is validated and verified by comparing the microstructure evolution with experimental EBSD results reported in the literature. The model is able to capture the ultrasonic softening effect and the results show that as the ultrasonic intensity increases, the plastic deformation also increases. Differences in the stress-strain response are explained based on the slip system orientation tensor (Schmidt factors) which depends upon the crystal orientation. © 2010 Elsevier B.V. All rights reserved.

  4. Softening and re-hardening of hadron transverse mass spectra in relativistic heavy-ion collisions

    International Nuclear Information System (INIS)

    Isse, M.; Otuka, N.; Ohnishi, A.; Sahu, P.K.; Nara, Y.

    2002-01-01

    At RHIC experiments, started at 2000, the data obtained recently seem to exhibit QGP formation, but the conclusion is not drawn yet. Here, we pay out attention to the collective motion at hadronic freeze-out as an evidence of QGP formation. The transverse mass spectra may show softening to re-hardening with increasing incident energy. We compare simulated results obtained in JAM' - a hadronic cascade model - with experimental data, and discuss weather the QGP is formed or not. (author)

  5. Finite element implementation of the Hoek-Brown material model with general strain softening behavior

    DEFF Research Database (Denmark)

    Sørensen, Emil Smed; Clausen, Johan Christian; Damkilde, Lars

    2015-01-01

    A numerical implementation of the Hoek–Brown criterion is presented, which is capable of modeling different post-failure behaviors observed in jointed rock mass. This is done by making the material parameters a function of the accumulated plastic strain. The implementation is for use in finite...... for perfectly-plastic, brittle and strain softening material behavior and the results are compared with known solutions....

  6. Mechanistic insight into softening of Canadian wonder common beans (Phaseolus vulgaris) during cooking.

    Science.gov (United States)

    Chigwedere, Claire Maria; Olaoye, Taye Foyeke; Kyomugasho, Clare; Jamsazzadeh Kermani, Zahra; Pallares Pallares, Andrea; Van Loey, Ann M; Grauwet, Tara; Hendrickx, Marc E

    2018-04-01

    The relative contributions of cotyledons and seed coats towards hardening of common beans (Phaseolus vulgaris) were investigated and the rate-limiting process which controls bean softening during cooking was determined. Fresh or aged whole beans and cotyledons were soaked and cooked in demineralised water or 0.1 M NaHCO 3 solution, and texture evolution, microstructure changes and thermal properties were studied. Fresh and aged whole beans cooked in demineralised water had significantly different softening rate constants and so did fresh and aged cotyledons. The comparable softening rate constants of aged whole beans and cotyledons indicated an insignificant role of the seed coat in hardening during storage. All samples cooked faster in 0.1 M NaHCO 3 solution. Disintegration of cooked tissues followed by microscopic examination revealed a transition from cell breakage through a phase of cell breakage and separation to complete cell separation with increased cooking time wherefore texture decayed. Therefore, progressive solubilization of pectin in the middle lamella greatly promoted texture decay. While residual birefringence even after substantial cooking time suggested some molecular order of the starch, calorimetric analyses revealed complete starch gelatinisation before complete cell separation occurred. This implies an insignificant role of starch in texture decay during cooking but its hindered uncoiling into a viscous gel after gelatinisation due to the restricting cell wall could promote its retrogradation. Therefore, we suggest that the rate-determining process in bean softening relates to cell wall/middle lamella changes influencing pectin solubilization. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Visceral and Somatic Disorders: Tissue Softening with Frequency-Specific Microcurrent

    OpenAIRE

    McMakin, Carolyn R.; Oschman, James L.

    2013-01-01

    Frequency-specific microcurrent (FSM) is an emerging technique for treating many health conditions. Pairs of frequencies of microampere-level electrical stimulation are applied to particular places on the skin of a patient via combinations of conductive graphite gloves, moistened towels, or gel electrode patches. A consistent finding is a profound and palpable tissue softening and warming within seconds of applying frequencies appropriate for treating particular conditions. Similar phenomena ...

  8. Influence of Lime and Phosphorus Application Rates on Growth of Maize in an Acid Soil

    Directory of Open Access Journals (Sweden)

    Peter Asbon Opala

    2017-01-01

    Full Text Available The interactive effects of lime and phosphorus on maize growth in an acid soil were investigated in a greenhouse experiment. A completely randomized design with 12 treatments consisting of four lime levels, 0, 2, 10, and 20 t ha−1, in a factorial combination with three phosphorus rates, 0, 30, and 100 kg ha−1, was used. Maize was grown in pots for six weeks and its heights and dry matter yield were determined and soils were analyzed for available P and exchangeable acidity. Liming significantly reduced the exchangeable acidity in the soils. The effect of lime on available P was not significant but available P increased with increasing P rates. There was a significant effect of lime, P, and P by lime interactions on plant heights and dry matter. Without lime application, dry matter increased with increasing P rates but, with lime, dry mattes increased from 0 to 30 kg P ha−1 but declined from 30 to 100 kg P ha−1. The highest dry matter yield (13.8 g pot−1 was obtained with a combined 2 t ha−1 of lime with 30 kg P ha−1 suggesting that lime application at low rates combined with moderate amounts of P would be appropriate in this soil.

  9. Experimental study of silty clay stabilization with cement and lime in multan, pakistan

    International Nuclear Information System (INIS)

    Sultan, T.

    2014-01-01

    Stabilization is valuable substitute for advancing the soil characteristics. The engineering features gained after stabilization differs broadly owing to non-uniformity in constitutions of soil. This study describes an assessment of cement and lime additives for advancing soils ventures. The effectiveness of lime and cement stabilization on geotechnical characteristics of the in situ soil has also been described in the paper. The additives like cement and lime were added in different dosage rates to examine the change in properties of the in situ soil. Cement addition caused an increase in unconfined compression strength (UCS) throughout from 4% to 16% of cement. Moreover, it has been observed that by adding lime, the early strength of clay increases up to 6% of lime but for long term strength i.e. 28 days maximum strengths is achieved for 4% of lime. It also confirms that with more percentage of lime and longer duration of curing, it expands. In addition to the strength behavior of samples at various percentages of cement and lime, the deflection at failure point was also examined. In order to make a straight comparison, both cement and lime stabilized soils were also tested in laboratory. Generally, the performance of Portland cement-stabilized soils was advanced to lime in the experiments performed. (author)

  10. Nanoscale thermal-mechanical probe determination of 'softening transitions' in thin polymer films

    International Nuclear Information System (INIS)

    Zhou Jing; Berry, Brian; Douglas, Jack F; Karim, Alamgir; Snyder, Chad R; Soles, Christopher

    2008-01-01

    We report a quantitative study of the softening behavior of glassy polystyrene (PS) films at length scales on the order of 100 nm using nano-thermomechanometry (nano-TM), an emerging scanning probe technique in which a highly doped silicon atomic force microscopy (AFM) tip is resistively heated on the surface of a polymer film. The apparent 'softening temperature' T s of the film is found to depend on the logarithm of the square root of the thermal ramping rate R. This relation allows us to estimate a quasi-equilibrium (or zero rate) softening transition temperature T s0 by extrapolation. We observe marked shifts of T s0 with decreasing film thickness, but the nature of these shifts, and even their sign, depend strongly on both the thermal and mechanical properties of the supporting substrate. Finite element simulations suggest that thin PS films on rigid substrates with large thermal conductivities lead to increasing T s0 with decreasing film thickness, whereas softer, less thermally conductive substrates promote reductions in T s0 . Experimental observations on a range of substrates confirm this behavior and indicate a complicated interplay between the thermal and mechanical properties of the thin PS film and the substrate. This study directly points to relevant factors for quantitative measurements of thermophysical properties of materials at the nanoscale using this nano-TM based method.

  11. Dynamic induced softening in frictional granular materials investigated by discrete-element-method simulation

    Science.gov (United States)

    Lemrich, Laure; Carmeliet, Jan; Johnson, Paul A.; Guyer, Robert; Jia, Xiaoping

    2017-12-01

    A granular system composed of frictional glass beads is simulated using the discrete element method. The intergrain forces are based on the Hertz contact law in the normal direction with frictional tangential force. The damping due to collision is also accounted for. Systems are loaded at various stresses and their quasistatic elastic moduli are characterized. Each system is subjected to an extensive dynamic testing protocol by measuring the resonant response to a broad range of ac drive amplitudes and frequencies via a set of diagnostic strains. The system, linear at small ac drive amplitudes, has resonance frequencies that shift downward (i.e., modulus softening) with increased ac drive amplitude. Detailed testing shows that the slipping contact ratio does not contribute significantly to this dynamic modulus softening, but the coordination number is strongly correlated to this reduction. This suggests that the softening arises from the extended structural change via break and remake of contacts during the rearrangement of bead positions driven by the ac amplitude.

  12. Strain softening during tension in cold drawn Cu–Ag alloys

    Energy Technology Data Exchange (ETDEWEB)

    Chang, L.L., E-mail: lilichang@sdu.edu.cn [School of Materials Science and Engineering, Shandong University, Jinan, Shandong 250061 (China); Wen, S.; Li, S.L.; Zhu, X.D. [School of Materials Science and Engineering, Shandong University, Jinan, Shandong 250061 (China); Shang, X.J. [Jinan Baoshida Industrial Development Co., Ltd, Jinan, Shandong 250061 (China)

    2015-10-15

    Experiments were conducted on Cu–0.1wt.%Ag alloys to evaluate the influence of producing procedures and annealing conditions on microstructure evolution and mechanical properties of Cu–Ag alloys. Optical microscopy (OM), electron back-scattered diffraction (EBSD), X-ray diffraction (XRD) and transmission electron microscopy (TEM) were used for microstructural evaluation and mechanical properties were characterized by tensile tests. The results indicated that hot-extruded Cu–Ag alloys had a typical dynamic recrystallized microstructure with equiaxed grains. Cold drawing at room temperature leaded to partial recrystallized microstructure with a mixture of coarse and fine grains. The dominate {001}<100 > cubic texture formed during hot extrusion was changed to be {112}<111 > copper texture by cold drawing. Strain softening occurred during room temperature tension of cold drawn Cu–Ag alloys with an average grain size of 13–19.7 μm. - Highlights: • Strain softening occurred during tension of Cu–Ag alloys with coarse grain size. • Work hardening was observed in hot-extruded and annealed Cu–0.1wt.%Ag alloys. • Strain softening was ascribed to dynamic recovery and dynamic recrystallization.

  13. Salivary a-amylase protects enamel surface against acid induced softening

    DEFF Research Database (Denmark)

    Lazovic, Maja Bruvo; Moe, Dennis; Kirkeby, Svend

    Objectives: Recently we have demonstrated individual differences in protection against acid-induced enamel softening offered by experimentally developed saliva pellicles. Although ethnicity seemed to be related to protection level, the saliva proteins responsible for the differences were not iden......Objectives: Recently we have demonstrated individual differences in protection against acid-induced enamel softening offered by experimentally developed saliva pellicles. Although ethnicity seemed to be related to protection level, the saliva proteins responsible for the differences were......, and one Chinese. After collection, saliva was dialysed and lyophilised and re-dissolved at 0.5% in Type I water. Next, four polished bovine enamel specimens were immersed into each sample under gentle and constant shaking for 12 hours. Last, specimens were exposed to an erosive challenge of pH 2.3 for 4......-TOF mass fingerprinting following trypsin digestion. Each persistent peak in the HPLC chromatograms was related to the protective effect against acid-induced enamel softening obtained by the corresponding saliva sample by multiple regression analysis. Results: One peak identified as a-amylase had...

  14. Visceral and somatic disorders: tissue softening with frequency-specific microcurrent.

    Science.gov (United States)

    McMakin, Carolyn R; Oschman, James L

    2013-02-01

    Frequency-specific microcurrent (FSM) is an emerging technique for treating many health conditions. Pairs of frequencies of microampere-level electrical stimulation are applied to particular places on the skin of a patient via combinations of conductive graphite gloves, moistened towels, or gel electrode patches. A consistent finding is a profound and palpable tissue softening and warming within seconds of applying frequencies appropriate for treating particular conditions. Similar phenomena are often observed with successful acupuncture, cranial-sacral, and other energy-based techniques. This article explores possible mechanisms involved in tissue softening. In the 1970s, neuroscientist and osteopathic researcher Irvin Korr developed a "γ-loop hypothesis" to explain the persistence of increased systemic muscle tone associated with various somatic dysfunctions. This article summarizes how physiologists, neuroscientists, osteopaths, chiropractors, and fascial researchers have expanded on Korr's ideas by exploring various mechanisms by which injury or disease increase local muscle tension or systemic muscle tone. Following on Korr's hypothesis, it is suggested that most patients actually present with elevated muscle tone or tense areas due to prior traumas or other disorders, and that tissue softening indicates that FSM or other methods are affecting the cause of their pathophysiology. The authors believe this concept and the research it has led to will be of interest to a wide range of energetic, bodywork, and movement therapists.

  15. Advanced treatment of swine wastewater using an agent synthesized from amorphous silica and hydrated lime.

    Science.gov (United States)

    Tanaka, Yasuo; Hasegawa, Teruaki; Sugimoto, Kiyomi; Miura, Keiichi; Aketo, Tsuyoshi; Minowa, Nobutaka; Toda, Masaya; Kinoshita, Katsumi; Yamashita, Takahiro; Ogino, Akifumi

    2014-01-01

    Advanced treatment using an agent synthesized from amorphous silica and hydrated lime (M-CSH-lime) was developed and applied to swine wastewater treatment. Biologically treated wastewater and M-CSH-lime (approximately 6 w/v% slurry) were fed continuously into a column-shaped reactor from its bottom. Accumulated M-CSH-lime gradually formed a bed layer. The influent permeated this layer and contacted the M-CSH-lime, and the treatment reaction progressed. Treated liquid overflowing from the top of the reactor was neutralized with CO₂gas bubbling. The colour removal rate approximately exceeded 50% with M-CSH-lime addition rates of > 0.15 w/v%. The removal rate of PO(3⁻)(4) exceeded 80% with the addition of>0.03 w/v% of M-CSH-lime. The removal rates of coliform bacteria and Escherichia coli exceeded 99.9% with > 0.1 w/v%. Accumulated M-CSH-lime in the reactor was periodically withdrawn from the upper part of the bed layer. The content of citric-acid-soluble P₂O₅ in the recovered matter was>15% when the weight ratio of influent PO(3⁻)(4) -P to added M-CSH-lime was > 0.15. This content was comparable with commercial phosphorus fertilizer. The inhibitory effect of recovered M-CSH-lime on germination and growth of leafy vegetable komatsuna (Brassica rapa var. perviridis) was evaluated by an experiment using the Neubauer's pot. The recovered M-CSH-lime had no negative effect on germination and growth. These results suggest that advanced water treatment with M-CSH-lime was effective for simultaneous removal of colour, [Formula: see text] and coliform bacteria at an addition rate of 0.03-0.15 w/v%, and that the recovered M-CSH-lime would be suitable as phosphorus fertilizer.

  16. In vitro utilization of lime treated olive cake as a component of complete feed for small ruminants.

    Science.gov (United States)

    Ishfaq, A; Sharma, R K; Rastogi, A; Malla, B A; Farooq, J

    2015-01-01

    The current in vitro study was carried out to determine the chemical composition and inclusion level of lime treated olive cake on acid detergent fiber (ADF) replacement basis in adult male goats. Crude olive cake was collected and evaluated for proximate composition and protein fractionation. It was treated with 6% lime and incubated for 1 week under room temperature in 2 kg sealed polythene bags and was evaluated for proximate composition after incubation. Different isonitrogenous complete diets containing 0-50% of lime treated olive cake on ADF replacement basis were formulated as per the requirement of adult male goats. In ADF replacement, fiber and concentrate sources were replaced by lime treated olive cake by replacing the 0-50% ADF percentage of the total 40% ADF value of complete feed. The formulated complete diets were tested for in vitro degradation parameters. Treatment of olive cake with 6% slaked lime increased availability of cellulose and alleviated digestibility depression caused by high ether extract percentage. Organic matter, nitrogen free extract, ADF and neutral detergent fiber were significantly lowered by lime treatment of olive cake. The cornell net carbohydrate and protein system analysis showed that non-degradable protein represented by acid detergent insoluble nitrogen (ADIN) was 21.71% whereas the non-available protein represented by neutral detergent insoluble nitrogen (NDIN) was 38.86% in crude olive cake. The in vitro dry matter degradation (IVDMD) values were comparable at all replacement levels. However, a point of inflection was observed at 40% ADF replacement level, which was supported by truly degradable organic matter (TDOM), microbial biomass production (MBP), efficiency of MBP and partitioning factor values (PF). In our study, we concluded that there is comparable difference in composition of Indian olive cake when compared with European olive cake. The most important finding was that about 78% of nitrogen present in Indian

  17. In vitro utilization of lime treated olive cake as a component of complete feed for small ruminants

    Directory of Open Access Journals (Sweden)

    A. Ishfaq

    2015-01-01

    Full Text Available Aim: The current in vitro study was carried out to determine the chemical composition and inclusion level of lime treated olive cake on acid detergent fiber (ADF replacement basis in adult male goats. Materials and Methods: Crude olive cake was collected and evaluated for proximate composition and protein fractionation. It was treated with 6% lime and incubated for 1 week under room temperature in 2 kg sealed polythene bags and was evaluated for proximate composition after incubation. Different isonitrogenous complete diets containing 0-50% of lime treated olive cake on ADF replacement basis were formulated as per the requirement of adult male goats. In ADF replacement, fiber and concentrate sources were replaced by lime treated olive cake by replacing the 0-50% ADF percentage of the total 40% ADF value of complete feed. The formulated complete diets were tested for in vitro degradation parameters. Results: Treatment of olive cake with 6% slaked lime increased availability of cellulose and alleviated digestibility depression caused by high ether extract percentage. Organic matter, nitrogen free extract, ADF and neutral detergent fiber were significantly lowered by lime treatment of olive cake. The cornell net carbohydrate and protein system analysis showed that non-degradable protein represented by acid detergent insoluble nitrogen (ADIN was 21.71% whereas the non-available protein represented by neutral detergent insoluble nitrogen (NDIN was 38.86% in crude olive cake. The in vitro dry matter degradation (IVDMD values were comparable at all replacement levels. However, a point of inflection was observed at 40% ADF replacement level, which was supported by truly degradable organic matter (TDOM, microbial biomass production (MBP, efficiency of MBP and partitioning factor values (PF. Conclusion: In our study, we concluded that there is comparable difference in composition of Indian olive cake when compared with European olive cake. The most

  18. Estimation of atmospheric fluoride by limed filter papers

    International Nuclear Information System (INIS)

    Smith, D.R.

    1988-09-01

    The limed filter paper method of static sampling of atmospheric fluoride is reviewed in this report. Use of the technique, in conjunction with precise measurement of the absorbed fluoride and calibration with dynamic air sampling techniques, to estimate atmospheric fluoride levels, is considered to give only qualitative data (± 50%). The limed filter paper method is site specific due to variations in meteorological conditions. Its main value is to indicate seasonal and annual trends in fluoride exposure of vegetation. Subject to these considerations, the lower and upper limits of atmospheric fluoride exposure and the applicability to atmospheric fluoride estimation under routine or emergency fluoride release conditions are discussed, with special emphasis on the limiting factors

  19. Wood ash as a soil additive and liming agent

    International Nuclear Information System (INIS)

    Campbell, A.; Etiegni, L.; Mahler, R.L.

    1991-01-01

    This study evaluated wood ash as an agricultural soil supplement and liming material. Winter wheat (Triticum aestivum) and poplar (Populus sp.) were grown in a greenhouse on six different Idaho soils amended with different ash concentrations. At ash levels equal to or lower than 2%, no detrimental effects were observed. In fact, the biomass of the wheat and the caliper and height of the poplar cuttings increased more at 2% ash 940 metric tons/ha than with the control soil. These results suggest that wood ash could be used in agricultural applications as a low analysis fertilizer containing potassium and as a liming agent. Land application of wood ash could be less expensive and more environmentally sound than present landfilling practices

  20. Repair mortars based on lime. Accelerated aging tests

    Directory of Open Access Journals (Sweden)

    Martínez-Ramírez, S.

    1995-06-01

    Full Text Available The behaviour under different accelerated aging tests (freeze/thaw and crystallization cycles of a new lime mortar with biocide properties destinated to monumental repair has been studied. New mortars (which have the biocide impregnated in a clay called sepiolite have a similar behaviour to lime mortars used as a reference. After the aging tests, the biocide properties of the mortars have been tried.

    Se ha estudiado el comportamiento frente a distintos ensayos de envejecimiento acelerado (ciclos de hielo/deshielo y cristalización de sales de un nuevo mortero de cal con propiedades biocidas, destinado a la reparación monumental. Se ha comprobado que los nuevos morteros (que llevan incorporado el biocida impregnado en una arcilla denominada sepiolita tienen un comportamiento muy similar a los morteros de cal utilizados como referencia. Tras los ensayos de envejecimiento se ha visto que las propiedades biocidas de los morteros se mantienen.

  1. Comparative study of engineering properties of two-lime waste tire particle soil and soil with lime/loess ratio of 3:7

    Science.gov (United States)

    Tiecheng, Yan; Xingyuan, Zhang; Hongping, Yang

    2018-03-01

    This study describes an analytical comparison of the engineering characteristics of two-lime waste tire particle soil and soil with lime/loess ratio of 3:7 using density measurements, results of indoor consolidation tests, and direct shear tests to examine the strength and deformation characteristics. It investigates the engineering performance of collapsible loess treated with waste tire particles and lime. The results indicate that (1) the shear strength of the two-lime waste tire particle soils increases continuously with soil age; and (2) the two-lime waste tire particle soils are light-weight, strong, and low-deformation soils, and can be applied primarily to improve the foundation soil conditions in areas with collapsible loess soils. This could address the problem of used tire disposal, while providing a new method to consider and manage collapsible loess soils.

  2. Innovative Lime Pozzolana Renders for Reconstruction of Historical Buildings

    International Nuclear Information System (INIS)

    Vejmelkova, E.; Maca, P.; Konvalinka, P.; Cerny, R.

    2011-01-01

    Bulk density, matrix density, open porosity, compressive strength, bending strength, water sorptivity, moisture diffusivity, water vapor diffusion coefficient, thermal conductivity, specific heat capacity and thermal diffusivity of two innovative renovation renders on limepozzolana basis are analyzed. The obtained results are compared with reference lime plaster and two commercial renovation renders, and conclusions on the applicability of the particular renders in practical reconstruction works are drawn. (author)

  3. Freezing and thawing resistance of aerial lime mortar with metakaolin\

    Czech Academy of Sciences Publication Activity Database

    Nunes, Cristiana Lara; Slížková, Zuzana

    2016-01-01

    Roč. 114, July (2016), s. 896-905 ISSN 0950-0618 R&D Projects: GA ČR(CZ) GBP105/12/G059 Institutional support: RVO:68378297 Keywords : freeze-thaw * lime * metakaolin * linseed oil * mortar * water-repellency Subject RIV: JN - Civil Engineering Impact factor: 3.169, year: 2016 http://www.sciencedirect.com/science/article/pii/S0950061816305645

  4. Between tradition and technological innovation: challenges to lime Heritage conservation

    Directory of Open Access Journals (Sweden)

    Marluci Menezes

    2016-01-01

    Full Text Available The aim is to discuss the relationship between traditional and scientific technological knowledge as innovative and fundamental to heritage conservation. It is argued that this innovation does not necessarily come from scientific knowledge, but potentially from a wise articulation between these two types of knowledge. This discussion starts from an already long process of reflection on lime heritage conservation, as developed in LNEC from research projects.

  5. Effect of the preparation of lime putties on their properties

    Czech Academy of Sciences Publication Activity Database

    Navrátilová, Eva; Tihlaříková, Eva; Neděla, Vilém; Rovnaníková, P.; Pavlík, J.

    2017-01-01

    Roč. 7, DEC (2017), s. 1-9, č. článku 17260. ISSN 2045-2322 R&D Projects: GA MŠk(CZ) LO1212; GA MŠk ED0017/01/01 Institutional support: RVO:68081731 Keywords : lime putties * micromorphology Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering OBOR OECD: Civil engineering Impact factor: 4.259, year: 2016 https://www.nature.com/articles/s41598-017-17527-3

  6. Application of different lime rates and phosphorus on soil physico ...

    African Journals Online (AJOL)

    The treatments were factorial combination of five rates of phosphorus (0, 11.5, 23, 46, 57.5 kg P2O5) and four rates of lime (CaCO3) (0, 2.25, 3 and 3.75 tons ha-1) in randomized complete block design and replicated three times. The pre soil analysis indicated that the soil of experimental area was acidic (pH = 5.31) and low ...

  7. Stool Softeners

    Science.gov (United States)

    ... 50 Plus® (as a combination product containing Docusate, Sennosides) ... Gentle Strength® (as a combination product containing Docusate, Sennosides) ... Gentlax S® (as a combination product containing Docusate, Sennosides)

  8. Speciation of aluminium, arsenic and molybdenum in excessively limed lakes

    International Nuclear Information System (INIS)

    Sjoestedt, Carin; Waellstedt, Teresia; Gustafsson, Jon Petter; Borg, Hans

    2009-01-01

    The possible existence of the potentially toxic oxyanions of Al (Al(OH) 4 - ), As (HAsO 4 2- ), and Mo (MoO 4 2- ) was examined in excessively limed lakes. In-situ dialysis (MWCO 1 kDa) was performed in the surface and bottom waters of two excessively limed lakes (pH 7.1-7.7) and one acidic lake (pH ∼ 5.4). The dialysable metal concentrations were compared to the equilibrium distribution of species as calculated with the geochemical code Visual MINTEQ incorporating the CD-MUSIC and Stockholm Humic models for complexation onto colloidal ferrihydrite and dissolved organic matter. Arsenic and molybdenum in the excessively limed lakes were to a large extent present in the dialysable fraction (> 79% and > 92% respectively). They were calculated to exist as free or adsorbed oxyanions. Most of the Al was observed to reside in the colloidal fraction (51-82%). In agreement with this, model predictions indicated aluminium to be present mostly as colloids or bound to dissolved organic matter. Only a small fraction was modelled as Al(OH) 4 - ions. In most cases, modelled values were in agreement with the dialysis results. The free concentrations of the three oxyanions were mostly low compared to toxic levels.

  9. Vanadium extraction from slimes by the lime-bicarbonate method

    International Nuclear Information System (INIS)

    Lishchenko, T.V.; Vdovina, L.V.; Slobodchikova, R.I.

    1978-01-01

    Some main parameters of the lime-bicarbonate method of extracting vanadium from residues obtained in washing waters of mazut boilers on thermal stations have been determined. To study the process of vanadium extraction during caking of the residues with lime and subsequent leaching of water-soluble vanadium, a ''Minsk-22'' computer has been used for computation. Analysis of the equation derived has shown that a change in temperature of vanadium leaching, density of pulp, and a kind of heating of the charge affect the process only slightly. It has also been shown that the calcination temperature is expedient to be kept above 850 deg C and consumption temperature is expedient to be kept above 85O deg C and consumption of lime must not exceed 20% of the residues weight. Bicarbonate consumption exerts a decisive influence on completeness of vanadium extraction and must be increased up to >35%; duration of leaching should be raised up to 30-45 minutes. With increasing calcination temperature the duration of leaching decreases. When temperature and duration of calcination increase, the formation of water-soluble vanadium intensifies. With the aid of optimization program seven variants have been chosen, which ensure vanadium extraction into solution by 95-100%

  10. Sorghum yield after liming and combinations of phosphorus sources

    Directory of Open Access Journals (Sweden)

    Thiago C. Silveira

    Full Text Available ABSTRACT Phosphate fertilization has increased sorghum yield, but few studies are available on sorghum production and efficient fertilizer management related to liming and phosphorus (P sources. This work evaluates production, dry matter partitioning and agronomic efficiency (AEI in successive sorghum cycles after application of limestone and combinations of phosphorus sources. Two cycles were conducted in sequence in the same experimental field, in a 2 x 6 factorial scheme, corresponding to soil with or without liming and six combinations of P2O5 sources: control (0 kg ha-1 P2O5, 100% Itafós natural phosphate (NP, 75% NP + 25% single superphosphate (SS, 50% NP + 50% SS, 25% NP + 75% SS and 100% SS. Pots with capacity for 8 dm3 were used in a randomized block design with four replicates. The first cycle, conducted in the summer/autumn season, reached the highest dry matter production and P accumulation in treatments with higher SS proportions, leading to higher AEI. Subsequently, in the second cycle, conducted considering only the residual phosphate fertilization of the first cycle, highest dry matter production and AEI were obtained in the treatment with 100% or higher proportions of natural phosphate in the presence of liming, most likely due to the gradual release of P.

  11. Thermophysical properties of hydrophobised lime plasters - The influence of ageing

    Science.gov (United States)

    Pavlíková, Milena; Zemanová, Lucie; Pavlík, Zbyšek

    2017-07-01

    The building envelope is a principal responsible for buildings energy loses. Lime plasters as the most popular finishing materials of historical buildings and culture monuments influence the thermal behaviour as well as construction material of masonry. On this account, the effect of ageing on the thermophysical properties of a newly designed lime plasters containing hydrophobic admixture is analysed in the paper. For the comparative purposes, the reference lime plaster is tested. The ageing is accelerated with controlled carbonation process to simulate the final plasters properties. Basic characterization of the tested materials is done using bulk density, matrix density, and porosity measurements. Thermal conductivity and volumetric heat capacity are experimentally assessed using a transient impulse method. The obtained data revealed the significant changes of the both studied thermal parameters in the dependence on plasters composition and age. The assessed material parameters will be stored in a material database, where will find use as an input data for computational modelling of heat transport in this type of porous building materials and evaluation of energy-savings and sustainability issues.

  12. Stress Softening Behavior in the Mucosa-Submucosa and Muscle Layers in Normal and Diabetic Rat Esophagus

    DEFF Research Database (Denmark)

    Jiang, Hongbo; Liao, Donghua; Zhao, Jingbo

    2015-01-01

    Background & aims: Stress softening is a feature of mechanical preconditioning in soft tissue. Previously, we demonstrated that esophageal stress softening is reversible by muscle activation with KCl. Since the esophagus consists of muscle and mucosa-submucosa layers, the aim was to study...... the stress softening behavior in these layers in normal and diabetic rat esophagus and how diabetes affect the reversibility of esophageal stress softening.Methods: Ten Wistar rats were injected with STZ and the average blood glucose level reached 25 mmol/L after 8 weeks. Ten rats were used as the normal......M KCl was added for maximum contraction for 3min. KCl was washed out to permit relaxation and contractions were eliminated by immersion into Ca2+-free solution. After 1h rest, the tubes were exposed to five repeated ramp distensions conformed to the aforesaid two series. Stress-strain curves were used...

  13. Analysis of papaya cell wall-related genes during fruit ripening indicates a central role of polygalacturonases during pulp softening.

    Directory of Open Access Journals (Sweden)

    João Paulo Fabi

    Full Text Available Papaya (Carica papaya L. is a climacteric fleshy fruit that undergoes dramatic changes during ripening, most noticeably a severe pulp softening. However, little is known regarding the genetics of the cell wall metabolism in papayas. The present work describes the identification and characterization of genes related to pulp softening. We used gene expression profiling to analyze the correlations and co-expression networks of cell wall-related genes, and the results suggest that papaya pulp softening is accomplished by the interactions of multiple glycoside hydrolases. The polygalacturonase cpPG1 appeared to play a central role in the network and was further studied. The transient expression of cpPG1 in papaya results in pulp softening and leaf necrosis in the absence of ethylene action and confirms its role in papaya fruit ripening.

  14. The Softening of Journalistic Political Communication: A Comprehensive Framework Model of Sensationalism, Soft News, Infotainment, and Tabloidization

    NARCIS (Netherlands)

    Otto, L.; Glogger, I.; Boukes, M.

    Despite the scholarly popularity of important developments of political communication, concepts like soft news or infotainment lack conceptual clarity. This article tackles that problem and introduces a multilevel framework model of softening of journalistic political communication, which shows that

  15. Models for predicting the mass of lime fruits by some engineering properties.

    Science.gov (United States)

    Miraei Ashtiani, Seyed-Hassan; Baradaran Motie, Jalal; Emadi, Bagher; Aghkhani, Mohammad-Hosein

    2014-11-01

    Grading fruits based on mass is important in packaging and reduces the waste, also increases the marketing value of agricultural produce. The aim of this study was mass modeling of two major cultivars of Iranian limes based on engineering attributes. Models were classified into three: 1-Single and multiple variable regressions of lime mass and dimensional characteristics. 2-Single and multiple variable regressions of lime mass and projected areas. 3-Single regression of lime mass based on its actual volume and calculated volume assumed as ellipsoid and prolate spheroid shapes. All properties considered in the current study were found to be statistically significant (ρ lime based on minor diameter and first projected area are the most appropriate models in the first and the second classifications, respectively. In third classification, the best model was obtained on the basis of the prolate spheroid volume. It was finally concluded that the suitable grading system of lime mass is based on prolate spheroid volume.

  16. Influence of lime juice on the severity of sickle cell anemia.

    Science.gov (United States)

    Adegoke, Samuel Ademola; Shehu, Umar Abdullahi; Mohammed, Lasisi Oluwafemi; Sanusi, Yunusa; Oyelami, Oyeku Akibu

    2013-06-01

    The pain in sickle cell anemia (SCA) is often triggered by dehydration, acidosis, and fever that are usually due to malaria. Intake of lime juice was recently demonstrated to facilitate clearance of the malaria parasite. It was therefore sought to determine whether regular intake of lime juice will ameliorate crisis, especially recurrent bone pain. In this preliminary, open-labeled, randomized study, the effects of lime juice on the clinical and some laboratory characteristics of children with SCA were tested. Among the 113 children with SCA studied in two hospitals, the 58 receiving lime treatment had lower rates of significant painful episodes than the 55 without lime (37 versus 83 crises in 6 months, and 0.64±0.11 versus 1.51±0.34 average rates per child, plime did not cause any significant side-effect. Regular intake of lime juice may be of great therapeutic and nutritional relevance in children with SCA.

  17. Plasticity, Swell-Shrink, and Microstructure of Phosphogypsum Admixed Lime Stabilized Expansive Soil

    Directory of Open Access Journals (Sweden)

    Jijo James

    2016-01-01

    Full Text Available The study involved utilization of an industrial waste, Phosphogypsum (PG, as an additive to lime stabilization of an expansive soil. Three lime dosages, namely, initial consumption of lime (ICL, optimum lime content (OLC, and less than ICL (LICL, were identified for the soil under study for stabilizing the soil. Along with lime, varying doses of PG were added to the soil for stabilization. The effect of stabilization was studied by performing index tests, namely, liquid limit, plastic limit, shrinkage limit, and free swell test, on pulverized remains of failed unconfined compression test specimens. The samples were also subjected to a microstructural study by means of scanning electron microscope. Addition of PG to lime resulted in improvement in the plasticity and swell-shrink characteristics. The microstructural study revealed the formation of a dense compact mass of stabilized soil.

  18. Thorough investigation of the oxygen heterocyclic fraction of lime (Citrus aurantifolia (Christm.) Swingle) juice.

    Science.gov (United States)

    Costa, Rosaria; Russo, Marina; De Grazia, Selenia; Grasso, Elisa; Dugo, Paola; Mondello, Luigi

    2014-04-01

    Reversed-phase-HPLC analysis by means of superficially porous silica particle columns (fused-core) was applied to the investigation of flavonoids, coumarins, and psoralens in lime juice samples. Hesperidin (367.0 ± 16.0 ppm) and eriocitrin (148.0 ± 7.9 ppm) were the most abundant flavonoids. Fifteen coumarins and furocoumarins were determined, including bergamottin (29.6 ± 1.1 ppm), 5-geranyloxy-7-methoxycoumarin (16.5 ± 0.6 ppm), and oxypeucedanin hydrate (9.9 ± 0.5 ppm) as predominant compounds. These molecules are today well known for their beneficial effects on human health. As a consequence, the present study, beyond investigating for the first time the chemical composition of lime juice, highlights also its health-promoting qualities, due to its content of flavonoids and coumarins. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Tetraploid Rangpur lime rootstock increases drought tolerance via enhanced constitutive root abscisic acid production.

    Science.gov (United States)

    Allario, Thierry; Brumos, Javier; Colmenero-Flores, Jose M; Iglesias, Domingo J; Pina, Jose A; Navarro, Luis; Talon, Manuel; Ollitrault, Patrick; Morillon, Raphaël

    2013-04-01

    Whole-genome duplication, or polyploidy, is common in many plant species and often leads to better adaptation to adverse environmental condition. However, little is known about the physiological and molecular determinants underlying adaptation. We examined the drought tolerance in diploid (2x) and autotetraploid (4x) clones of Rangpur lime (Citrus limonia) rootstocks grafted with 2x Valencia Delta sweet orange (Citrus sinensis) scions, named V/2xRL and V/4xRL, respectively. Physiological experiments to study root-shoot communication associated with gene expression studies in roots and leaves were performed. V/4xRL was much more tolerant to water deficit than V/2xRL. Gene expression analysis in leaves and roots showed that more genes related to the response to water stress were differentially expressed in V/2xRL than in V/4xRL. Prior to the stress, when comparing V/4xRL to V/2xRL, V/4xRL leaves had lower stomatal conductance and greater abscisic acid (ABA) content. In roots, ABA content was higher in V/4xRL and was associated to a greater expression of drought responsive genes, including CsNCED1, a pivotal regulatory gene of ABA biosynthesis. We conclude that tetraploidy modifies the expression of genes in Rangpur lime citrus roots to regulate long-distance ABA signalling and adaptation to stress. © 2012 Blackwell Publishing Ltd.

  20. Effects of experimental acidification on mobilisation of metals from sediments of limed and non-limed lakes

    International Nuclear Information System (INIS)

    Waellstedt, Teresia; Borg, Hans

    2003-01-01

    In order to study the influence of pH on the mobilisation of metals from lake sediments, intact sediment cores with overlying water were sampled from one lime treated lake and one acidified lake. The overlying water of two cores from each lake was successively acidified to pH 4.2 over a period of 3 months. In the acid treated samples from the limed lake, the initial concentrations of Al, Cd, Mn, Pb and Zn in the overlying water were generally lower and the final concentrations were higher than in the acid treated samples from the acidified lake. The labile inorganic fraction of Al (Al i ) was increasingly dominating as pH decreased. Redox potential and pH in the sediment indicated that the upper two centimetres were involved in the exchange reactions. The experiment showed that mobilisation of metals from sediments can occur and the results indicated that mobilisation could contribute to increased concentrations of metals in lake water during reacidification of formerly lime treated lakes. - Reacidification leads to mobilisation of metals from lake sediments

  1. Strain-softening behavior of an Fe-6.5 wt%Si alloy during warm deformation and its applications

    International Nuclear Information System (INIS)

    Fu Huadong; Zhang Zhihao; Yang Qiang; Xie Jianxin

    2011-01-01

    Research highlights: → An Fe-6.5 wt%Si alloy exhibits strain-softening behavior after large deformation. → The decrease of the order degree is responsible for the strain-softening behavior. → The strain-softening behavior of Fe-6.5 wt%Si alloy can be applied in cold rolling. → An Fe-6.5 wt%Si thin strip with thickness of 0.20 mm is fabricated by cold rolling. - Abstract: An Fe-6.5 wt%Si alloy with columnar grains was compressed at a temperature below its recrystallization temperature. The Vickers hardness and structure of the alloy before and after deformation were investigated. The results showed that with an increase in the degree of deformation, Vickers hardness of the alloy initially increased rapidly and then decreased slowly, indicating that the alloy had a strain-softening behavior after a large deformation. Meanwhile, the work-hardening exponent of the alloy decreased significantly. Transmission electron microscopy confirmed that the decrease of the order degree was responsible for the strain-softening behavior of the deformed alloy. Applying its softening behavior, the Fe-6.5 wt%Si alloy with columnar grains was rolled at 400 deg. C and then at room temperature. An Fe-6.5 wt%Si thin strip with thickness of 0.20 mm was fabricated. The surface of the strip was bright and had no obvious edge cracks.

  2. Influence of the mechanical properties of lime mortar on the strength of brick masonry

    OpenAIRE

    PAVIA, SARA

    2013-01-01

    PUBLISHED This paper aims at improving the quality of lime mortar masonry by understanding the mechanics of mortars and masonry and their interaction. It investigates how the mortar?s compressive and flexural strengths impact the compressive and bond strength of clay brick masonry bound with calcium lime (CL) and natural hydraulic lime (NHL) mortars. It concludes that the strength of the bond has a greater impact on the compressive strength of masonry than the mortar?s st...

  3. Short-term responses of wetland vegetation after liming of an Adirondack watershed

    Energy Technology Data Exchange (ETDEWEB)

    Mackun, I.R.; Leopold, D.J.; Raynal, D.J. (State Univ. of New York, Syracuse, NY (United States))

    1994-08-01

    Watershed liming has been suggested as a long-term mitigation strategy for lake acidity, particularly in areas subject to high levels of acidic deposition. However, virtually no information has been available on the impacts of liming on wetland vegetation. In 1989, 1100 Mg of limestone (83.5% CaCO[sub 3]) were aerially applied to 48% (100 ha) of the Woods Lake watershed in the west-central Adirondack region of New York as part of the first comprehensive watershed liming study in North America. We inventoried wetland vegetation in 1.0-m[sup 2] plots before liming and during the subsequent 2 yr. Within this period liming influenced the cover, frequency, or importance values of only 6 of 64 wetland taxa. The cover of Sphagnum spp. and of the cespitose sedge Carex interior decreased in control relative to limed plots, and cover of the rhizomatous sedge Cladium mariscoides increased nearly threefold in limed areas. These two sedges, which are relatively tall, are characteristic of more calcareous habitats. Cover of the grass Muhlenbergia uniflora, cover and importance were adversely affected or inhibited by lime. It is unclear whether liming directly inhibited the growth of these three small-statured species, or whether the adverse effects of lime were mediated through shifts in competitive interactions with other species. The limited responses that we observed to liming, along with changes that occurred in control plots over the study period, may indicate that in the short term watershed liming was no more of a perturbation than the environmental factors responsible for natural annual variation in wetland communities.

  4. DEVELOPMENT OF TECHNIQUES FOR QUANTITATIVE ANALYSIS OF LIME FLOWERS

    Directory of Open Access Journals (Sweden)

    Demyanenko DV

    2016-03-01

    Full Text Available Introduction. The article is devoted to the development of techniques for quantitative analysis of lime flower in order to make amendments to existing pharmacopoeian monographs for this herbal drug. Lime inflorescences contain lipophilic biologically active substances (BAS causing notable antimicrobial and anti-inflammatory effects and also more polar phenolic compounds with antiulcer activity. Considering this, it’s necessary to regulate all these groups of BAS quantitatively. Materials and methods. For this study six batches of lime flowers harvested in 2008-2009 yrs. in Kharkiv, Rivno and Zhitomir regions were used as crude herbal drug. Loss on drying was determined by routine pharmacopoeian procedures. Total content of lipophilic substances was determined gravimetrically after Soxhlet extraction of samples 1, 5, 7 and 10 g in weight with methylene chloride, considering that by its extracting ability this solvent is close to liquefied difluorochloromethane (freon R22 used by us for obtaining of lipophilic complexes. The duration of complete analytical extraction was determined by infusion of six 10 g assays of lime flowers during 1, 2, 3, 4, 5, 6 hours, then quantity of lipophilic extractives was revealed gravimetrically. Quantity of essential oil in lime flowers was evaluated under the procedure of ЕР7, 2.8.12. Weight of the herbal drug sample was 200 g, distillation rate – 2,5- 3,5 ml/min, volume of distillation liquid (water – 500 ml, volume of xylene in the graduated tube – 0,50 ml. Total flavonoid content recalculated to quercetin was determined after hydrolysis with acidified acetone, withdrawing of flavonoid aglycones with ethylacetate and by further spectrophotometry of their complexes with aluminium chloride. All quantitative determinations were replicated five times for each assay. All chemicals and reagents were of analytical grade. Results and discussion. It was found that adequate accuracy of the analysis of lipophilic

  5. Use of catchment liming for the improvement of drainage water quality from smelter-impacted lands near Coniston, Ontario

    Energy Technology Data Exchange (ETDEWEB)

    Gunn, J.M.; Sein, R.; Keller, B. [Laurentian Univ., Sudbury, ON (Canada) Dept. of Biology

    1999-07-01

    A study was carried out to test whether INCO Ltd.'s aerial land liming program, designed solely for revegetation purposes, was improving water quality from the treated sites in an area affected by air pollution from acidic nickel and copper smelters. A wetland application mehod was tested as a potentially improved technique of drainage water treatment. A summary is included of the results of water quality assessment and bioassay toxicity testing for the experimental catchments during the study period 1991-1997. There were immediate spin-off benefits from the stream monitoring study that were rapidly applied to the larger land reclamation effort. The identified effectivess of the coarse limestone led to testing and adoption of new methods of aerial liming in which finer pelletized materials were used both reducing the application rate and the associated costs. The decline in Cu and Ni during 1991-1994 indicated that the metal contamination of the site was declining even before the first limestone treatment. The occurrence of a brief pulse in metal concentrations immediately after the wetland liming treatments is consistent with an earlier occurrence and supports the hypothesis that liming may temporarily increase metal concentrations in stream water through displacement of metal cations at the soil exchange sites by the added Ca. The presence of acidic groundwater proved to be a confounding factor that reduced the effectiveness of soil and wetland treatments at the site. In spite of surprises, the catchment treatments, particularly the wetland applications, proved to be very effective at improving water quality in much of the catchment stream. 14 refs., 2 figs., 1 tab.

  6. The influence of partial replacement of hemp shives by expanded perlite on physical properties of hemp-lime composite

    Science.gov (United States)

    Brzyski, Przemysław; Widomski, Marcin

    2017-07-01

    The use of waste plants in building materials production is consistent with the principles of sustainable development, including waste management, CO2 balance, biodegradability of the material e.g. after building demolition. The porous structure of plant materials determines their usability as the insulation materials. An example of plant applicable in the construction industry is the industrial hemp. The shives are produced from the wooden core of the hemp stem as lightweight insulating filler in the composite based on lime binder. The discussed hemp-lime composite, due to the presence of lightweight, porous organic aggregates exhibits satisfactory thermal insulation properties and is used as filling and insulation of walls (as well as roofs and floors) in buildings of the wooden frame construction. The irregular shape of shives and their low density causes nonhomogenous compaction of composite and the formation of voids between the randomly arranged shives. In this paper the series of hemp-lime composites were tested. Apart from hemp shives, an additional aggregate - expanded perlite was used as a fine, lightweight, thermal insulating filler. Application of the additional aggregate was aimed to fill the voids between hemp shives and to investigate its influence on the physical properties of composite: apparent density, total porosity, water absorption and thermal conductivity.

  7. Lime sulfur toxicity to broad mite, to its host plants and to natural enemies.

    Science.gov (United States)

    Venzon, Madelaine; Oliveira, Rafael M; Perez, André L; Rodríguez-Cruz, Fredy A; Martins Filho, Sebastião

    2013-06-01

    An acaricidal effect of lime sulfur has not been demonstrated for Polyphagotarsonemus latus. However, lime sulfur can cause toxicity to natural enemies and to host plants. In this study, the toxicity of different concentrations of lime sulfur to P. latus, to the predatory mite Amblyseius herbicolus and to the predatory insect Chrysoperla externa was evaluated. Additionally, the phytotoxicity of lime sulfur to two P. latus hosts, chili pepper and physic nut plants, was determined. Lime sulfur at a concentration of 9.5 mL L(-1) restrained P. latus population growth. However, this concentration was deleterious to natural enemies. The predatory mite A. herbicolus showed a negative value of instantaneous growth rate, and only 50% of the tested larvae of C. externa reached adulthood when exposed to 10 mL L(-1) . Physic nut had severe injury symptoms when sprayed with all tested lime sulfur concentrations. For chili pepper plants, no phytoxicity was observed at any tested concentration. Lime sulfur might be used for P. latus control on chili pepper but not on physic nut owing to phytotoxicity. Care should be taken when using lime sulfur in view of negative effects on natural enemies. Selective lime sulfur concentration integrated with other management tactics may provide an effective and sustainable P. latus control on chili pepper. © 2012 Society of Chemical Industry.

  8. Enhanced inhibition of Aspergillus niger on sedge (Lepironia articulata) treated with heat-cured lime oil.

    Science.gov (United States)

    Matan, N; Matan, N; Ketsa, S

    2013-08-01

    This study aimed to examine heat curing effect (30-100°C) on antifungal activities of lime oil and its components (limonene, p-cymene, β-pinene and α-pinene) at concentrations ranging from 100 to 300 μl ml(-1) against Aspergillus niger in microbiological medium and to optimize heat curing of lime oil for efficient mould control on sedge (Lepironia articulata). Broth dilution method was employed to determine lime oil minimum inhibitory concentration, which was at 90 μl ml(-1) with heat curing at 70°C. Limonene, a main component of lime oil, was an agent responsible for temperature dependencies of lime oil activities observed. Response surface methodology was used to construct the mathematical model describing a time period of zero mould growth on sedge as functions of heat curing temperature and lime oil concentration. Heat curing of 90 μl ml(-1) lime oil at 70°C extended a period of zero mould growth on sedge to 18 weeks under moist conditions. Heat curing at 70°C best enhanced antifungal activity of lime oil against A. niger both in medium and on sedge. Heat curing of lime oil has potential to be used to enhance the antifungal safety of sedge products. © 2013 The Society for Applied Microbiology.

  9. Lime application methods, water and bottom soil acidity in fresh water fish ponds

    Directory of Open Access Journals (Sweden)

    Queiroz Julio Ferraz de

    2004-01-01

    Full Text Available Although some methods for determining lime requirement of pond soils are available and commonly used, there is still no consensus on whether it is more effective to apply liming materials to the bottoms of empty ponds or to wait and apply them over the water surface after ponds are filled. There is also little information on how deep lime reacts in pond sediment over time, and whether the depth of reaction is different when liming materials are applied to the water or to the soil. Therefore, three techniques for treating fish ponds with agricultural limestone were evaluated in ponds with clayey soils at a commercial fish farm. Amounts of agricultural limestone equal to the lime requirement of bottom soils were applied to each of three ponds by: direct application over the pond water surface; spread uniformly over the bottom of the empty pond; spread uniformly over the bottom of the empty pond followed by tilling of the bottom. Effectiveness of agricultural limestone applications did not differ among treatment methods. Agricultural limestone also reacted quickly to increase total alkalinity and total hardness of pond water to acceptable concentrations within 2 weeks after application. The reaction of lime to increase soil pH was essentially complete after one to two months, and lime had no effect below a soil depth of 8 cm. Tilling of pond bottoms to incorporate liming materials is unnecessary, and tilling consumes time and is an expensive practice; filled ponds can be limed effectively.

  10. Characterization of cutting soda-lime glass sludge for the formulation of red ceramic products

    International Nuclear Information System (INIS)

    Filogonio, P.H.C.; Reis, A.S.; Louzada, D.M.; Della, V.P.

    2014-01-01

    Considering previous works that have demonstrated the feasibility of soda-lime glass incorporation into red ceramics, this paper aims to determine the potential for incorporation of cutting soda-lime glass sludge in red ceramic manufacturing. Therefore, the waste was characterized by X-ray fluorescence, X-ray diffraction, particle size distribution and thermal behavior. The results confirm the chemical and mineralogical similarity between waste and soda-lime glass. Because of this similarity, it is concluded that the soda-lime glass waste has the capability to be used in the manufacturing of red ceramics. (author)

  11. First evidence of lime burning in southern Scandinavia: lime kilns found at the royal residence on the west bank of Lake Tissø

    DEFF Research Database (Denmark)

    Henriksen, Peter Steen; Holst, Sandie

    2015-01-01

    In connection with investigations of the aristocratic residence at Tissø from the Viking Age, the earliest evidence so far of lime burning in Denmark has been excavated. The excavations unearthed traces of up to five lime kilns which were subsequently dated to the end of the ninth century....... This corresponds well with the dating of the erection of the hall in the third construction phase at Fugledegård. Finds of mud-and-wattle with whitewashing show that the lime was used to whitewash the halls at Tissø in both the Germanic Iron Age and the Viking Age. Analyses of lime from the lime kilns...... and the whitewashed mud-and-wattle demonstrate that the raw material for the lime burning was mainly travertine deposited in spring water, but that bryozoan limestone was also used. The lime kilns were just under 2 m in diameter with stone-built edges, and there are indications that the superstructure may have been...

  12. Core-softened fluids, water-like anomalies, and the liquid-liquid critical points.

    Science.gov (United States)

    Salcedo, Evy; de Oliveira, Alan Barros; Barraz, Ney M; Chakravarty, Charusita; Barbosa, Marcia C

    2011-07-28

    Molecular dynamics simulations are used to examine the relationship between water-like anomalies and the liquid-liquid critical point in a family of model fluids with multi-Gaussian, core-softened pair interactions. The core-softened pair interactions have two length scales, such that the longer length scale associated with a shallow, attractive well is kept constant while the shorter length scale associated with the repulsive shoulder is varied from an inflection point to a minimum of progressively increasing depth. The maximum depth of the shoulder well is chosen so that the resulting potential reproduces the oxygen-oxygen radial distribution function of the ST4 model of water. As the shoulder well depth increases, the pressure required to form the high density liquid decreases and the temperature up to which the high-density liquid is stable increases, resulting in the shift of the liquid-liquid critical point to much lower pressures and higher temperatures. To understand the entropic effects associated with the changes in the interaction potential, the pair correlation entropy is computed to show that the excess entropy anomaly diminishes when the shoulder well depth increases. Excess entropy scaling of diffusivity in this class of fluids is demonstrated, showing that decreasing strength of the excess entropy anomaly with increasing shoulder depth results in the progressive loss of water-like thermodynamic, structural and transport anomalies. Instantaneous normal mode analysis was used to index the overall curvature distribution of the fluid and the fraction of imaginary frequency modes was shown to correlate well with the anomalous behavior of the diffusivity and the pair correlation entropy. The results suggest in the case of core-softened potentials, in addition to the presence of two length scales, energetic, and entropic effects associated with local minima and curvatures of the pair interaction play an important role in determining the presence of water

  13. Low-temperature behavior of core-softened models: Water and silica behavior

    International Nuclear Information System (INIS)

    Jagla, E. A.

    2001-01-01

    A core-softened model of a glass forming fluid is numerically studied in the limit of very low temperatures. The model shows two qualitatively different behaviors depending on the strength of the attraction between particles. For no or low attraction, the changes of density as a function of pressure are smooth, although hysteretic due to mechanical metastabilities. For larger attraction, sudden changes of density upon compressing and decompressing occur. This global mechanical instability is correlated to the existence of a thermodynamic first-order amorphous-amorphous transition. The two different behaviors obtained correspond qualitatively to the different phenomenology observed in silica and water

  14. Extracting material response from simple mechanical tests on hardening-softening-hardening viscoplastic solids

    Science.gov (United States)

    Mohan, Nisha

    Compliant foams are usually characterized by a wide range of desirable mechanical properties. These properties include viscoelasticity at different temperatures, energy absorption, recoverability under cyclic loading, impact resistance, and thermal, electrical, acoustic and radiation-resistance. Some foams contain nano-sized features and are used in small-scale devices. This implies that the characteristic dimensions of foams span multiple length scales, rendering modeling their mechanical properties difficult. Continuum mechanics-based models capture some salient experimental features like the linear elastic regime, followed by non-linear plateau stress regime. However, they lack mesostructural physical details. This makes them incapable of accurately predicting local peaks in stress and strain distributions, which significantly affect the deformation paths. Atomistic methods are capable of capturing the physical origins of deformation at smaller scales, but suffer from impractical computational intensity. Capturing deformation at the so-called meso-scale, which is capable of describing the phenomenon at a continuum level, but with some physical insights, requires developing new theoretical approaches. A fundamental question that motivates the modeling of foams is `how to extract the intrinsic material response from simple mechanical test data, such as stress vs. strain response?' A 3D model was developed to simulate the mechanical response of foam-type materials. The novelty of this model includes unique features such as the hardening-softening-hardening material response, strain rate-dependence, and plastically compressible solids with plastic non-normality. Suggestive links from atomistic simulations of foams were borrowed to formulate a physically informed hardening material input function. Motivated by a model that qualitatively captured the response of foam-type vertically aligned carbon nanotube (VACNT) pillars under uniaxial compression [2011,"Analysis of

  15. PSD Permit for the Marblehead Lime Company

    Science.gov (United States)

    This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  16. Liming effect on P availability from Maardu phosphate rock

    International Nuclear Information System (INIS)

    Sidlauskas, G.; Masauskas, S.; Ezerinskas, V.

    2002-01-01

    Thirty years ago phosphate rock from the Maardu deposit was intensively used for soil fertilization in Lithuania. However, the application of finely ground product caused an undesirable dusty operation. Afterwards, a super-phosphate production plant was built in Kedainiai and the use of phosphate rock was completely abandoned. Field experiments with fodder beets and barley were carried out to evaluate the P availability of granulated superphosphate and Maardu phosphate rock. The comparison was made at three acidity levels: a) unlimed acid soil with a high content of Al (pH kcl 4.3-4.4, hydrolytic acidity was 41-44 meq/kg soil), b) soil limed with 0.5n rate CaCO 3 powder limestone based on hydrolytic acidity, and c) soil limed with 1.0n rate CaCO 3 . Two field experiments were carried out with fodder beets. In 1997 the yield increased significantly due to liming. However, no significant yield increases were found due to the application of phosphorus fertilizers. Differences between the effect of superphosphate and phosphate rock were also not observed. This might have been caused by a severe drought during the vegetative growth of plants. In the following year, 1998, a soil with similar acidity was chosen, however it contained even lower amounts of available phosphorus in the arable soil (about 50 mg/kg soil A-L method). In the unlimed soil the yield was low, the effect of superphosphate was better than that of phosphate rock. A good fodder beet yield of 32 to 35 t/ha was obtained and the effect of phosphate rock was better than that of superphosphate at 0.5n CaCO 3 rate. When liming with at the high rate (1.0n CaCO 3 rate according to hydrolytic acidity) the action of phosphate rock declined, and a better yield was obtained with superphosphate. Barley was grown after fodder beets in the 1997 experimental field and the residual effect of superphosphate and phosphate rock was investigated. Weather conditions were favorable for barley growth. Therefore a normal yield

  17. CHEMICAL ANALYSIS OF DENSE-GAS EXTRACTS FROM LIME FLOWERS

    Directory of Open Access Journals (Sweden)

    Demyanenko DV

    2015-04-01

    Full Text Available The purpose of this work was to make qualitative and quantitative analysis of phenolic biologically active substances (BAS in the extracts produced from lime flowers with condensed gases, using method of high-performance liquid chromatography (HPLC. Materials and methods: materials for this study were the extracts obtained by consequent processing of the herbal drug and marcs thereof with various condensed gases: difluorochloromethane (Freon R22, difluoromethane (Freon R32, azeotropic mixture of difluoromethane with pentafluoroethane (Freon 410A and freon-ammonium mixture. Extracts obtained with the latter were subjected to further fractionation by liquidliquid separation into hexane, chloroform, ethyl acetate and aqueous-alcohol phases. Besides, the supercritical СО2 extract, obtained from the herbal drug under rather strong conditions (at temperature 60°С and pressure 400 bar, was studied in our previous research. Presence of phenolic BAS and their quantity in the researched samples were determined by method of HPLC with UVspectrometric detection. Results and discussion: It has been found that Freon R22 extracted trace amounts of rutin from lime flowers – its content was only 0.08% of the total extract weight. On the other hand, Freons R32 and R410А showed good selectivity to moderately polar BAS of lime flowers (derivatives of flavonoids and hydroxycinnamic acids: in particular, the extract obtained with freon R32 contained about 1.3% of the total phenolic substances, and it was the only one of the investigated condensed gases used by us which took the basic flavonoid of lime flowers tiliroside – its content was 0.42% of extract weight. Also Freons R32 and R410А were able to withdraw another compound dominating among phenolic substances in the yielded extracts. Its quantity was rather noticeable – up to 0.87% of extract weight. This substance was not identified by existing database, but its UV-spectrum was similar to those of

  18. PCM-enhanced lime plasters for vernacular and contemporary architecture

    Science.gov (United States)

    Theodoridou, Magdalini; Kyriakou, Loucas; Ioannou, Ioannis

    2016-04-01

    In 1997, the European Union (EU) pledged to reduce the amount of greenhouse gas emissions by 20% below the levels of 1990 by the end of 2020. In recent years it has become evident that, in order to reach that goal, EU Member States must take measures to encourage sustainability in the building industry, which is a major energy consumer. Such measures should involve the use of innovative, environmentally friendly materials and methods in new constructions, as well as the renovation of existing properties by upgrading their current state of energy efficiency. Phase Change Materials (PCMs) have the ability to absorb and release thermal energy, in the form of latent heat, during the melting or solidifying processes respectively. Thus, they may be used as additives in the production of thermally efficient composite building materials. A PCM-enhanced plaster is a heat storage medium combining an appropriate PCM with a cementitious or non-cementitious matrix to produce a low-cost thermal storage material with structural and thermostatic properties. Although innovative technologies, such as PCMs, have certainly contributed to the boost in the evolution of the building materials industry in recent years, a significant proportion of these technologies and practices have not yet been fully exploited in materials based on traditional principles. This paper focuses on the design and production of novel cementless PCM-enhanced lime plasters, in line with the traditional production technology of lime composites. The new plasters are produced using either hydrated or natural hydraulic lime binder, crushed calcarenite sand (0-2 mm) and commercial microencapsulated PCM in powder form (5% w/w of solids). Results from comparative tests between reference mixtures and mixtures with the addition of PCM, carried out 28, 56 and 90 days after laboratory production, prove the potential of PCMs in enhancing the thermal performance of traditional lime-based composites. The modified composites

  19. Hydration products of lime-metakaolin pastes at ambient temperature with ageing

    Energy Technology Data Exchange (ETDEWEB)

    Gameiro, A., E-mail: agameiro@lnec.pt [National Laboratory of Civil Engineering, Materials Department, Av. do Brasil, 101, 1700 Lisbon (Portugal); Santos Silva, A., E-mail: ssilva@lnec.pt [National Laboratory of Civil Engineering, Materials Department, Av. do Brasil, 101, 1700 Lisbon (Portugal); Veiga, R., E-mail: rveiga@lnec.pt [National Laboratory of Civil Engineering, Buildings Department, Av. do Brasil, 101, 1700 Lisbon (Portugal); Velosa, A., E-mail: avelosa@ua.pt [Department of Civil Engineering, Geobiotec, University of Aveiro, Campus Universitario de Santiago, 3810-193 Aveiro (Portugal)

    2012-05-10

    Highlights: Black-Right-Pointing-Pointer We study the compounds formed in lime/MK blended pastes and their stability over time. Black-Right-Pointing-Pointer Different mixes of lime/MK pastes show different reaction kinetics during curing time, being the pozzolanic compounds formed directly proportional to the lime by MK replacement. Black-Right-Pointing-Pointer Some pozzolanic products are found to be unstable during the hydration reaction employed in our study. - Abstract: Mortars constituted of lime mixtures with pozzolanic additions have been extensively used in the past for the construction of historic and traditional buildings. This paper presents the results of blended pastes of lime and metakaolin (MK), namely compounds formed and their stability over time. This research is part of an extensive study aiming at the formulation of lime based mortars for restoration purposes. It has been shown for several years that MK has been applied in inorganic binders due to its capacity to react vigorously with calcium hydroxide (CH). In the presence of water originating a series of major hydrated phases, namely tetra calcium aluminate hydrate (C{sub 4}AH{sub 13}), calcium silicates hydrates (CSH) and calcium aluminium silicate hydrates (stratlingite - C{sub 2}ASH{sub 8}). Several blended pastes of lime and MK, with different substitution rates of lime by MK (wt%) were prepared and cured at a temperature of 20 Degree-Sign C and relative humidity RH > 95%. The phase composition of the formed hydrated phases was determined by X-ray diffraction (XRD) and simultaneous thermal analysis (TG-DTA). The obtained results showed that lime/MK pastes compositions displayed different reaction kinetics during curing time, being the pozzolanic products content directly proportional to the substitution rate of lime by MK. Also, a relationship between the increase stratlingite content and the MK substitution rate of lime by MK was found.

  20. Cell wall structures leading to cultivar differences in softening rates develop early during apple (Malus x domestica) fruit growth.

    Science.gov (United States)

    Ng, Jovyn K T; Schröder, Roswitha; Sutherland, Paul W; Hallett, Ian C; Hall, Miriam I; Prakash, Roneel; Smith, Bronwen G; Melton, Laurence D; Johnston, Jason W

    2013-11-19

    There is a paucity of information regarding development of fruit tissue microstructure and changes in the cell walls during fruit growth, and how these developmental processes differ between cultivars with contrasting softening behaviour. In this study we compare two apple cultivars that show different softening rates during fruit development and ripening. We investigate whether these different softening behaviours manifest themselves late during ethylene-induced softening in the ripening phase, or early during fruit expansion and maturation. 'Scifresh' (slow softening) and 'Royal Gala' (rapid softening) apples show differences in cortical microstructure and cell adhesion as early as the cell expansion phase. 'Scifresh' apples showed reduced loss of firmness and greater dry matter accumulation compared with 'Royal Gala' during early fruit development, suggesting differences in resource allocation that influence tissue structural properties. Tricellular junctions in 'Scifresh' were rich in highly-esterified pectin, contributing to stronger cell adhesion and an increased resistance to the development of large airspaces during cell expansion. Consequently, mature fruit of 'Scifresh' showed larger, more angular shaped cells than 'Royal Gala', with less airspaces and denser tissue. Stronger cell adhesion in ripe 'Scifresh' resulted in tissue fracture by cell rupture rather than by cell-to-cell-separation as seen in 'Royal Gala'. CDTA-soluble pectin differed in both cultivars during development, implicating its involvement in cell adhesion. Low pectin methylesterase activity during early stages of fruit development coupled with the lack of immuno-detectable PG was associated with increased cell adhesion in 'Scifresh'. Our results indicate that cell wall structures leading to differences in softening rates of apple fruit develop early during fruit growth and well before the induction of the ripening process.

  1. Lime and fertilizer recommendation system for coconut trees

    Directory of Open Access Journals (Sweden)

    Gustavo Nogueira Guedes Pereira Rosa

    2011-02-01

    Full Text Available Fertilizer recommendation to most agricultural crops is based on response curves. Such curves are constructed from field experimental data, obtained for a particular condition and may not be reliable to be applied to other regions. The aim of this study was to develop a Lime and Fertilizer Recommendation System for Coconut Crop based on the nutritional balance. The System considers the expected productivity and plant nutrient use efficiency to estimate nutrient demand, and effective rooting layer, soil nutrient availability, as well as any other nutrient input to estimate the nutrient supply. Comparing the nutrient demand with the nutrient supply the System defines the nutrient balance. If the balance for a given nutrient is negative, lime and, or, fertilization is recommended. On the other hand, if the balance is positive, no lime or fertilizer is needed. For coconut trees, the fertilization regime is divided in three stages: fertilization at the planting spot, band fertilization and fertilization at the production phase. The data set for the development of the System for coconut trees was obtained from the literature. The recommendations generated by the System were compared to those derived from recommendation tables used for coconut crop in Brazil. The main differences between the two procedures were for the P rate applied in the planting hole, which was higher in the proposed System because the tables do not pay heed to the pit volume, whereas the N and K rates were lower. The crop demand for K is very high, and the rates recommended by the System are superior to the table recommendations for the formation and initial production stage. The fertilizer recommendations by the System are higher for the phase of coconut tree growth as compared to the production phase, because greater amount of biomass is produced in the first phase.

  2. Mechanisms underlying recovery of zooplankton in Lake Orta after liming

    Directory of Open Access Journals (Sweden)

    Roberta Piscia

    2016-04-01

    Full Text Available The goal of this study was to improve the understanding of the large-scale mechanisms underlying the recovery of the zooplankton of Lake Orta from historical contamination, following reduced input of ammonia and metals and the subsequent 1989/90 liming intervention. The industrial pollution had been severe and long-lasting (1929-1990. Zooplankton biodiversity has improved, but most of the new taxa appearing in our counts are rotifers, while many calanoids and the large cladoceran predators (Bythotrephes and Leptodora that are common in the nearby Lake Maggiore, were still absent from Lake Orta 17 years after liming. To aid understanding of the large-scale mechanisms controlling changes in annual richness, we assessed the annual persistence (P of Crustacea and Rotifera taxa as an estimator of whether propagules that survived introduction, as result of the natural recolonization process, also thrived. We found that the rate of introduction of zooplankton colonists and their persistence in the water column of Lake Orta changed from 1971 to 2007. New rotifer taxa appeared in the lake after the mid-1980s, when discharge of toxic substances decreased, but their annual persistence was low (P<0.5 until the turn of the century. The numerical values of rotifer and crustacean persistence in Lake Orta were unexpectedly high in 2001 and 2007 (0.55 and 0.72 for rotifers, 0.85 and 0.86 for crustacean, respectively, much higher than in limed lakes in Sudbury, Canada, and in adjacent Lake Maggiore. We hypothesize this could be related to the lack of Cladoceran predators and zooplanktivorous fish in the pelagic waters of Lake Orta.

  3. Autoclaved Sand-Lime Products with a Polypropylene Mesh

    Science.gov (United States)

    Kostrzewa, Paulina; Stępień, Anna

    2017-10-01

    The paper presents the results of the research on modifications of silicate bricks with a polypropylene mesh and their influence on physical, mechanical and microstructural properties of such bricks. The main goal of the paper was to determine effects of the polypropylene mesh on sand-lime product parameters. The analysis has focused on compressive strength, water absorption, bulk density and structural features of the material. The obtained product is characterized by improved basic performance characteristics compared to traditional silicate products. Using the polypropylene mesh increased compressive strength by 25% while decreasing the product density. The modified products retain their form and do not disintegrate after losing their bearing capacity.

  4. Pore structure and carbonation in blended lime-cement pastes

    Directory of Open Access Journals (Sweden)

    Álvarez, J. I.

    2006-06-01

    Full Text Available The present study aims to gain a fuller understandingof the curing process in lime pastes (100, 90, 80, 70,60, 50 and 40% lime blended with cement by analyzingcarbonation in these materials. A hydrated, airslaked lime powder and CEM II A/L 32.5 Portlandcement were used for the blends. These materialswere singled out for research primarily because theymay be used in the restoration of heritage monuments.Variation in weight was used as an indicator for carbonation.A new parameter, A, was found to vary inverselywith the percentage of the cement because of theprevalence of Knudsen diffusion in the paste, in turndue to the characteristics of the pore structure, whichwas studied by mercury intrusion porosimetry (MIP.The hygroscopic study conducted on the different pastesprovided information on water content at a givenhumidity and its location, i.e., adsorbed on the surfaceof the pores or condensed inside them, obstructing thediffusion of CO2. The conclusion drawn from this studyof the curing process was that neither drying nor C3Shydration retarded lime carbonation.En este trabajo se estudia el proceso de carbonatacionen pastas mixtas de cal y cemento (100, 90, 80, 70, 60,50 y 40% de cal con el objeto de obtener un mejorconocimiento del proceso de curado en estos materiales.Para ello se ha empleado una cal aerea hidratada en polvoy un cemento Portland del tipo CEM II A/L 32,5. Enparticular, este estudio investiga estos materiales ya quepueden ser utilizados en la restauracion del PatrimonioCultural. Se ha utilizado la variacion de peso como indicadordel proceso de carbonatacion. Se ha establecidoun nuevo parametro, A, que varia inversamente con elporcentaje de cemento en la pasta, debido al predominiode la difusion de Knudsen como consecuencia de laestructura porosa, que ha sido estudiada por medio deporosimetria de intrusion de mercurio (PIM. El estudiohigroscopico realizado sobre las diversas pastas permiteconocer el contenido en agua a una

  5. Deformation twins and related softening behavior in nanocrystalline Cu–30% Zn alloy

    International Nuclear Information System (INIS)

    Bahmanpour, Hamed; Youssef, Khaled M.; Horky, Jelena; Setman, Daria; Atwater, Mark A.; Zehetbauer, Michael J.; Scattergood, Ronald O.; Koch, Carl C.

    2012-01-01

    Nanocrystalline Cu–30% Zn samples were produced by high energy ball milling at 77 K and room temperature. Cryomilled flakes were further processed by ultrahigh strain high pressure torsion (HPT) or room temperature milling to produce bulk artifact-free samples. Deformation-induced grain growth and a reduction in twin probability were observed in HPT consolidated samples. Investigations of the mechanical properties by hardness measurements and tensile tests revealed that at small grain sizes of less than ∼35 nm Cu–30% Zn deviates from the classical Hall–Petch relation and the strength of nanocrsytalline Cu–30% Zn is comparable with that of nanocrystalline pure copper. High resolution transmission electron microscopy studies show a high density of finely spaced deformation nanotwins, formed due to the low stacking fault energy of 14 mJ m –2 and low temperature severe plastic deformation. Possible softening mechanisms proposed in the literature for nanotwin copper are addressed and the twin-related softening behavior in nanotwinned Cu is extended to the Cu–30% Zn alloy based on detwinning mechanisms.

  6. TO SELECTION OF TECHNOLOGICAL SCHEME OF SOFTENING HEAT TREATMENT FOR HIGH CHROMIUM CAST IRON

    Directory of Open Access Journals (Sweden)

    V. G. Efremenko

    2014-03-01

    Full Text Available Purpose. High chromium cast irons with austenitic matrix have low machinability. The aim of work is search of new energy-saving modes of preliminary softening heat treatment enhancing the machinability of castings by forming an optimum microstructure. Methodology. Metallographic analysis, hardness testing and machinability testing are applied. Findings. It was found out that high temperature annealing with continuous cooling yields to martensite-austenite matrix in cast iron 270Х15Г2Н1MPhT, which abruptly affects the machinability of cast iron. Significant improvement of machinability is achieved by forming of structure "ferrite + granular carbides" and by decline of hardness to 37-39 HRC in the case of two-stage isothermal annealing in the subcritical temperature range or by the use of quenching and tempering (two-step or cyclic. Originality. It was found that the formation of the optimal structure of the matrix and achievement of desired hardness level needed for improving machinability of high chromium cast iron containing 3 % austenite-forming elements, can be obtained: 1 due to pearlite original austenite followed by spherodization eutectoid carbides, and 2 by getting predominantly martensite structure followed by the decay of martensite and carbides coagulation at high-temperature tempering. Practical value. The new energy-saving schemes of softening heat treatment to ensure the growth of machinability of high chromium cast iron, alloyed by higher quantity of austenite forming elements, are proposed.

  7. Softening Behavior of a New Al-Zn-Mg-Cu Alloy Due to TIG Welding

    Science.gov (United States)

    Zhang, Liang; Li, Xiaoyan; Nie, Zuoren; Huang, Hui; Sun, Jiantong

    2016-05-01

    A new Al-Zn-Mg-Cu alloy with T6 temper was welded by TIG welding, and the softening behavior of the joint was evaluated. Results show that the ultimate tensile strength of the joint is 436.2 ± 26.4 MPa which is about 64.5% of that of the base metal (BM). Fusion zone (FZ) is the weakest region even though its microhardness increases from 107.6 to 131.3 HV within 90 days after welding. Microhardness of the heat-affected zone (HAZ) adjacent to FZ increases from 125.2 to 162.3 HV within 90 days. However, a valley value of microhardness appears in the rest of the HAZ that increases from 112.1 to 128.1 HV within 90 days. The variation of grain size and precipitates is regarded as the main cause of softening in both FZ and HAZ. The grain size of FZ is about 33.9 μm, whereas 8.7 and 8.4 μm for HAZ and BM, respectively. A large number of η' phases distribute dispersively in BM, whereas precipitates in FZ identified as GPI zones are finer and fewer. Besides, precipitates in HAZ adjacent to FZ are also GPI zones. Precipitates in HAZ far away from FZ are coarser and fewer than those in BM and η phases begin to emerge.

  8. Magnetic enhancement and softening of fault gouges during seismic slip: Laboratory observation and implications

    Science.gov (United States)

    Yang, T.; Chen, J.; Dekkers, M. J.

    2017-12-01

    Anomalous rock magnetic properties have been reported in slip zones of many previous earthquakes (e.g., the 1995 Kobe earthquake, Japan; the 1999 Chi-Chi earthquake, Taiwan, and the 2008 Wenchuan earthquake, China). However, it is unclear whether short-duration frictional heating can actually induce such rock magnetic anomalies in fault zones; identification of this process in natural fault zones is not that straightforward. A promising approach to solve this problem is to conduct high-velocity friction (HVF) experiments that reproduce seismic fault movements and frictional heating in a simulated fault zone. Afterwards natural fault zones can be analyzed with renewed insight. Our HVF experiments on fault gouges that are simulating large amounts of earthquake slip, show significant magnetic enhancement and softening of sheared gouges. Mineral magnetic measurements reveal that magnetite was formed due to thermal decomposition of smectite during the HVF experiment on the paramagnetic fault gouge. Also, goethite was transformed to intermediate magnetite during the HVF experiment on the goethite-bearing fault gouge. Magnetic susceptibility, saturation remanence and saturation magnetization of sheared samples are linearly increasing with and strongly depend on the temperature rise induced by frictional heating; in contrast, coecivities are decreasing with increasing temperature. Thus, frictional heating can induce thermal decomposition/transformation during short-duration, high-velocity seismic slip, leading to magnetic enhancement and softening of a slip zone. Mineral magnetic methods are suited for diagnosing earthquake slip and estimating the temperature rise of co-seismic frictional heating.

  9. Solute softening and defect generation during prismatic slip in magnesium alloys

    Science.gov (United States)

    Yi, Peng; Cammarata, Robert C.; Falk, Michael L.

    2017-12-01

    Temperature and solute effects on prismatic slip of 〈a〉 dislocations in Mg are studied using molecular dynamics simulation. Prismatic slip is controlled by the low mobility screw dislocation. The screw dislocation glides on the prismatic plane through alternating cross-slip between the basal plane and the prismatic plane. In doing so, it exhibits a locking-unlocking mechanism at low temperatures and a more continuous wavy propagation at high temperatures. The dislocation dissociates into partials on the basal plane and the constriction formation of the partials is identified to be the rate-limiting process for unlocking. In addition, the diffusion of partials on the basal plane enables the formation of jogs and superjogs for prismatic slip, which lead to the generation of vacancies and dislocation loops. Solute softening in Mg alloys was observed in the presence of both Al and Y solute. The softening in prismatic slip is found to be due to solute pinning on the basal plane, instead of the relative energy change of the screw dislocation on the basal and prismatic planes, as has been hypothesized.

  10. Simulation of crack propagation in steel plate with strain softening model

    Energy Technology Data Exchange (ETDEWEB)

    Chan, O.B.; Elwi, A.E.; Grondin, G.Y.

    2006-05-15

    A new material model for simulating the fracture behaviour of structural steel was presented. Recent research on crack initiation and continuum damage mechanics was presented. A modified continuum damage model was also evaluated. Strain softening elements were then used to simulate material cracks in a steel structure. The analysis then compared load versus displacement and load versus clip-gauge displacement curves from various different experimental and numerical studies. A finite element analysis technique was used to simulate the fracture behaviour of 3-points bending specimens. Results of the analysis showed that the model predicted 90 per cent of the load and stress intensity factor at fracture initiation. A BE 365 electric shovel boom was used in the study to simulate fracture behaviour. Coupon test specimens were used to validate analysis predictions. It was concluded that the model was able to reduce the stiffness of the boom when the softening element reached yield strength limits during fracture initiation. 29 refs., 12 tabs., 58 figs.

  11. Assessment of dynamic softening mechanisms in Allvac 718Plus{sup TM} by EBSD analysis

    Energy Technology Data Exchange (ETDEWEB)

    Mitsche, Stefan, E-mail: stefan.mitsche@felmi-zfe.at [Institute for Electron Microscopy, Graz University of Technology, Steyrergasse 17, Graz (Austria); Sommitsch, Christof [Institute for Material Science and Welding, Christian Doppler Laboratory for Materials Modelling and Simulation, Graz University of Technology, Graz (Austria); Huber, Daniel; Stockinger, Martin [Boehler Schmiedetechnik GmbH and Co KG, Kapfenberg (Austria); Poelt, Peter [Institute for Electron Microscopy, Graz University of Technology, Steyrergasse 17, Graz (Austria)

    2011-04-25

    Research highlights: {yields} EBSD investigations of hot deformed superalloy Allvac 718Plus{sup TM}. {yields} Dynamic softening (recovery, DDRX and CDRX) in dependence on the temperature and strain rate. {yields} At high temperature (1050 deg. C) and high strain rate (10 s{sup -1}) mainly DDRX. {yields} At high temperature (1050 deg. C) and low strain rate (0.1 s{sup -1}) combination of DDRX, CDRX and recovery. - Abstract: The nickel-based superalloy Allvac 718Plus{sup TM} is a future candidate for turbine disc applications, as this new material combines the formability and cost advantages of Alloy 718 with the higher temperature capability of Waspaloy. Due to the strong influence of the microstructure on the final mechanical properties, a fundamental knowledge of the dynamic recrystallization mechanism of Allvac 718Plus{sup TM} is of great importance in order to develop precise microstructure evolution models for this material. Compression tests were performed at temperatures of 900 deg. C to 1050 deg. C and strain rates between 0.1 s{sup -1} and 10 s{sup -1}. The microstructures obtained were analyzed by electron backscatter diffraction (EBSD) to evaluate the influence of the different hot forming parameters on the dynamic softening processes of Allvac 718Plus{sup TM}.

  12. Softening of the elastic shear mode C{sub 66} in iron-based superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Boehmer, Anna; Burger, Philipp [Karlsruher Institut fuer Technologie, Institut fuer Festkoerperphysik, D-76021 Karlsruhe (Germany); Karlsruher Institut fuer Technologie, Fakultaet fuer Physik, D-76128 Karlsruhe (Germany); Hardy, Frederic; Schweiss, Peter; Fromknecht, Rainer; Wolf, Thomas; Meingast, Christoph [Karlsruher Institut fuer Technologie, Institut fuer Festkoerperphysik, D-76021 Karlsruhe (Germany); Reinecker, Marius; Schranz, Wilfried [Universitaet Wien, Fakultaet fuer Physik, A-1090 Wien, Vienna (Austria)

    2013-07-01

    The structural phase transition of underdoped iron-based superconductors is accompanied by a large softening of the elastic shear mode C{sub 66}, which has attracted considerable attention. This softening has been discussed both in terms of orbital and spin-nematic fluctuations which would be responsible for the structural phase transition and, possibly, superconductivity. However, sample requirements have so far restricted experimental investigations of C{sub 66} (via measurements of the ultrasound velocity) to the Ba(Fe,Co){sub 2}As{sub 2} system. Here, we report on a new technique, based on a three-point bending setup, to probe the Young's modulus of a sample with a capacitance dilatometer. For certain orientations, the Young's modulus is related to the elastic constant C{sub 66} whose effective temperature dependence can be obtained. Platelet-like samples, as frequently encountered for iron-based systems, are easily studied with our setup. Data on several systems are presented and discussed.

  13. Effect of a core-softened O-O interatomic interaction on the shock compression of fused silica

    Science.gov (United States)

    Izvekov, Sergei; Weingarten, N. Scott; Byrd, Edward F. C.

    2018-03-01

    Isotropic soft-core potentials have attracted considerable attention due to their ability to reproduce thermodynamic, dynamic, and structural anomalies observed in tetrahedral network-forming compounds such as water and silica. The aim of the present work is to assess the relevance of effective core-softening pertinent to the oxygen-oxygen interaction in silica to the thermodynamics and phase change mechanisms that occur in shock compressed fused silica. We utilize the MD simulation method with a recently published numerical interatomic potential derived from an ab initio MD simulation of liquid silica via force-matching. The resulting potential indicates an effective shoulder-like core-softening of the oxygen-oxygen repulsion. To better understand the role of the core-softening we analyze two derivative force-matching potentials in which the soft-core is replaced with a repulsive core either in the three-body potential term or in all the potential terms. Our analysis is further augmented by a comparison with several popular empirical models for silica that lack an explicit core-softening. The first outstanding feature of shock compressed glass reproduced with the soft-core models but not with the other models is that the shock compression values at pressures above 20 GPa are larger than those observed under hydrostatic compression (an anomalous shock Hugoniot densification). Our calculations indicate the occurrence of a phase transformation along the shock Hugoniot that we link to the O-O repulsion core-softening. The phase transformation is associated with a Hugoniot temperature reversal similar to that observed experimentally. With the soft-core models, the phase change is an isostructural transformation between amorphous polymorphs with no associated melting event. We further examine the nature of the structural transformation by comparing it to the Hugoniot calculations for stishovite. For stishovite, the Hugoniot exhibits temperature reversal and associated

  14. Cytotoxic and antibacterial activity of the mixture of olive oil and lime cream in vitro conditions.

    Science.gov (United States)

    Sumer, Zeynep; Yildirim, Gulay; Sumer, Haldun; Yildirim, Sahin

    2013-01-01

    The mixture of olive oil and lime cream has been traditionally used to treat external burns in the region of Hatay/Antakya and middle Anatolia. Olive oil and lime cream have been employed by many physicians to treat many ailments in the past. A limited number of studies have shown the antibacterial effect of olive oil and that it does not have any toxic effect on the skin. But we did not find any reported studies on the mixture of olive oil and lime cream. The aim of this paper is to investigate the cytotoxic and antibacterial activity of olive oil and lime cream individually or/and in combination in vitro conditions, by using disk-diffusion method and in cell culture. The main purpose in using this mixture is usually to clear burns without a trace. Agar overlay, MTT (Cytotoxicity assay) and antibacterial susceptibility tests were used to investigate the cytotoxic and antibacterial activity of olive oil and lime cream. We found that lime cream has an antibacterial activity but also cytotoxic on the fibroblasts. On the other hand olive oil has limited or no antibacterial effect and it has little or no cytotoxic on the fibroblasts. When we combined lime cream and olive oil, olive oil reduced its cytotoxic impact. These results suggest that mixture of olive oil and lime cream is not cytotoxic and has antimicrobial activity.

  15. Self-healing of lime based mortars : Microscopy observations on case studies

    NARCIS (Netherlands)

    Lubelli, B.; Nijland, T.G.; Van Hees, R.P.J.

    2011-01-01

    Lime mortars have, up to a certain extent, a self-healing capacity which may contribute to their durability. Self-healing in lime mortars consists of a process of dissolution, transport and re-precipitation of calcium compounds to heal cracks and fissures. The spontaneous occurrence of self-healing

  16. Self-healing of lime based mortars: Microscopy observations on case studies

    NARCIS (Netherlands)

    Lubelli, B.; Nijland, T.G.; Hees, R.P.J. van

    2011-01-01

    Lime mortars have, up to a certain extent, a self-healing capacity which may contribute to their durability. Self-healing in lime mortars consists of a process of dissolution, transport and re-precipitation of calcium compounds to heal cracks and fissures. The spontaneous occurrence of self-healing

  17. 77 FR 45715 - Application of Key Lime Air Corporation for Commuter Authority

    Science.gov (United States)

    2012-08-01

    ... DEPARTMENT OF TRANSPORTATION Office of the Secretary [Docket DOT-OST-2009-0116] Application of Key Lime Air Corporation for Commuter Authority AGENCY: Department of Transportation. ACTION: Notice of... Lime Air Corporation fit, willing, and able, and awarding it a Commuter Air Carrier Authorization...

  18. The effect of reuse of unhairing-liming residual floats through ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-09-03

    Sep 3, 2008 ... Key words: Unhairing-liming process, reusing, leather industry, environment, bacterial and fungal numbers. INTRODUCTION .... 4.0 x101. -: No growth. Chemical analysis of samples. Chemical analyses of sodium sulphide and lime were done for the regeneration of ULP residual liquors. While preparing ...

  19. Interpreting chemistry and technology of lime binders and implementing it in the conservation field

    Directory of Open Access Journals (Sweden)

    Georgia Zacharopoulou

    2009-01-01

    Full Text Available The objective of the paper is the compilation, review and dissemination of updated scientific knowledge on lime theory and technology in the field of heritage conservation. The strong evidence of the last decade's research on the positive effect of the - not demonstrable by a chemical equation – 'key' missing link of the maturation process is highlighted. It is demonstrated that the exceptional perfor -mance characteristics of durable lime based mortars predominately rely on the capacity for rapid, efficient and extensive carbonation of the air-hardening phase of limes, in particular when matured (nanoparticle wet slaked lime putties are used; and on the chemical and mechanical stability of the strength components (principally CSHs of the hydraulic phase of limes, which is higher in their more crystalline forms of historical lime-pozzolan mixtures than in their amorphous forms of modern cements. Hence, physicochemical adhesion and cohesion bonds both at the lime matrix and at the binder/aggregate interfaces are ensured imparting minimization of cracks and durability to lime based mortars and historic masonries. The comprehensive documentation of the former leads to optimal materials and procedures to preserve our cultural heritage.

  20. Lime-Stabilized Black Cotton Soil and Brick Powder Mixture as Subbase Material

    Directory of Open Access Journals (Sweden)

    S. Srikanth Reddy

    2018-01-01

    Full Text Available Various researchers, for the past few decades, had tried to stabilize black cotton soil using lime for improving its shrinkage and swelling characteristics. But these days, the cost of lime has increased resulting in increase in need for alternative and cost effective waste materials such as fly ash and rice husk ash. Brick powder, one among the alternative materials, is a fine powdered waste that contains higher proportions of silica and is found near brick kilns in rural areas. The objective of the study is to investigate the use of lime-stabilized black cotton soil and brick powder mixture as subbase material in flexible pavements. Black cotton soil procured from the local area, tested for suitability as subbase material, turned out to be unsuitable as it resulted in very less CBR value. Even lime stabilization of black cotton soil under study has not showed up the required CBR value specified for the subbase material of flexible pavement by MORTH. Hence the lime-stabilized black cotton soil is proportioned with brick powder to obtain optimum mixture that yields a better CBR value. The mixture of 20% brick powder and 80% lime-stabilized black cotton soil under study resulted in increase in the CBR value by about 135% in comparison with lime-stabilized black cotton soil. Thus it is promising to use the mixture of brick powder and lime-stabilized black cotton soil as subbase material in flexible pavements.

  1. Molecular characterization and pathogenicity assays of Colletotrichum acutatum, causal agent for lime anthracnose in Texas

    Science.gov (United States)

    Several distorted Mexican lime [Citrus aurantiifolia (Christm). Swingle] fruit, leaf, and twig samples with lime anthracnose symptoms were collected from three trees in residential areas of Brownsville, Texas. The causal fungal organism, Colletotrichum acutatum J. H. Simmonds was isolated from leave...

  2. Substrate pH and butterfly bush response to dolomitic lime or steel slag amendment

    Science.gov (United States)

    Steel slag is a fertilizer amendment with a high concentration of calcium oxide, and thus capable of raising substrate pH similar to dolomitic lime. Steel slag, however, contains higher concentrations of some nutrients, such as iron, manganese, and silicon, compared to dolomitic lime. The objectiv...

  3. The Strength Behaviour of Lime Stabilized Organic Clay Soil Modified by Catalyst Additeives

    Directory of Open Access Journals (Sweden)

    Khitam Abdulhussein Saeed

    2016-12-01

    Full Text Available The organic clay soil can be found in many large size reclaimed lands. These soils present enormously high settlement potential and low strength that needs to be improved by means of effective ground improvement techniques. One of the low cost techniques is to modify the soil with lime in-situ to make it suitable for construction and allow it to increase in strength by pozzolanic reactions between lime and clay minerals. Lime is known to be an effective stabilization material for clayey soil. Nevertheless, its effectiveness may be less with organic clay due to low effective strength properties. Thus, this study concerns the addition of catalyst i.e. zeolite which may improve the performance of lime stabilization to accelerate lime-organic clay reactions. The unconfined compressive test (UCT is conducted on remoulded samples (38mm x 80mm for 0, 7, 14 , 28, and 90 days of curing period. The addition of synthetic zeolite in lime-organic stabilized soil has increased the soil strength by 185% at 90 days curing period at the design mix of organic clay + 10% lime +10% zeolite. The higher value of UCS indicates that zeolite is an effective catalyst to enhance lime stabilization.

  4. Effect of liming on the molybdenum content in the root and leaf of ...

    African Journals Online (AJOL)

    Three liming treatments were employed (1, 3 and 4 t/ha CaCO3). The liming operation used on pseudogley induced a statistically significant increase in molybdenum ion absorption into the root system of tomato. Independently from the aforementioned, the values for the root and leaf molybdenum content of tomato in each ...

  5. Belowground ectomycorrhizal fungal communities respond to liming in three southern Swedish coniferous forest stands

    DEFF Research Database (Denmark)

    Kjøller, Rasmus; Clemmensen, Karina

    2009-01-01

    In this study we report on changes in the belowground ectomycorrhizal fungal communities in southern Swedish coniferous forests as a consequence of liming with 3-7 ton limestone per hectare 16 years prior to the study. A total of 107 ectomycorrhizal fungi were identified from 969 independently...... sampled root tips by sequencing the internal transcribed spacer region of the ribosomal DNA. Forty, 59 and 51 species were identified in three pine and spruce forests. Within all sites only about 25% of the species overlapped between the limed and the reference areas. However, the most abundant species...... were often found in both limed and reference plots and 60-70% of the root tips at each site were colonised by species occurring in both limed and reference plots. Across all three sites, fungal species belonging to the genus Tylospora and the order Pezizales became significantly more frequent in limed...

  6. Gasification of sulphate soap for the lime kiln

    Energy Technology Data Exchange (ETDEWEB)

    Saviharju, Kari (Valtion Teknillinen Tutkimuskeskus, Espoo (Finland). Lab. of Fuel and Process Technology); Timonen, Tuomas (Finnish Energy Economy Association, Espoo (Finland). Finnish Recovery Boiler Committee)

    1993-01-01

    Sulphate soap is a by-product of pulp mills utilized as a raw material for the chemical industry. However, this results in an increase in sulphur input of several kilograms SO[sub 2] per ADt pulp into the mill. Another increasingly interesting alternative is to utilize soap in the lime kiln of the mill. This has a positive effect, in addition to sulphur problems, on the energy balance of the mill. The crucial problem is the high Na + K content of soap, from 4 to 8%, which can result in plugging of the lime kiln. The operational problems can be avoided by gasifying the soap and by separating the inorganic materials from the product gas before the kiln. This paper describes research work on the gasification of crude sulphate soap carried out at the Technical Research Centre of Finland (VTT) over the years 1991 and 1992. This work will be continued in 1993 by focusing on specified problems, after which commercial applications should be available. (author)

  7. The effect of lime pre-treatments of date palm leaves on delignification and in vitro rumen degradability

    NARCIS (Netherlands)

    Ghorbani, M.; Ahmadi, F.; Rajaee Rad, A.; Zamiri, M.J.; Cone, J.W.; Polikarpov, I.

    2017-01-01

    Experiments were conducted to determine the effect of lime pre-treatment on the chemical composition and in vitro rumen degradability of date palm leaves (DPL). Lime pre-treatments, with or without oxygen supply, were applied for 1, 2 and 3 weeks at 25 and 40 °C. Lime was neutralized by the

  8. Liming Influences Growth and Nutrient Balances in Sugar Maple (Acer saccharum) Seedlings on an Acidic Forest Soil

    Science.gov (United States)

    Dudley J. Raynal

    1998-01-01

    Forests in the northeastern US have been limed to mitigate soil acidification and the acidity of surface waters and to improve soil base cation status. Much of the area considered for liming is within the range of sugar maple (Acer saccharum), but there is a poor understanding of how liming influences growth and nutrient balance of this species on...

  9. Action time effect of lime on its depressive ability for pyrite

    Institute of Scientific and Technical Information of China (English)

    Tichang Sun

    2004-01-01

    Two sample groups of bulk concentrates consisting mainly of pyrite and chalcopyrite from Daye and Chenghchao Mines in Hubei Province of China were used to investigate the effect of the action time of lime on its depressive ability for pyrite. The experimental results conducted with different samples and collectors showed that the action time between lime and pyrite markedly influences the depressive ability of lime. The depressive ability of lime increased with the action time increasing. It was also proved that the depressive results obtained at a large lime dosage after a shorter action time are similar to those obtained at a small lime dosage after a longer action time. The increase of depressive ability of lime after a longer action time is because that there are different mechanisms in different action time. The composition on the surface of pyrite acted for different time with lime was studied by using ESCA (Electron Spectroscopic Chemical Analysis). The results showed that iron hydroxide and calcium sulphate formed on the pyrite surface at the presence of lime in the pulp but the amounts of iron hydroxide and calcium sulphate were different at different action time. At the beginning action time the compound formed on the pyrite surface was mainly calcium sulphate and almost no iron hydroxide formed; but with the action time increasing, iron hydroxide formed. The longer the action time, the more iron hydroxide and the less calcium sulphate formed. It was considered that the stronger depressive ability of lime after a longer action time is because more iron hydroxide forms on the pyrite surface.

  10. Origin of C. latifolia and C. aurantiifolia triploid limes: the preferential disomic inheritance of doubled-diploid 'Mexican' lime is consistent with an interploid hybridization hypothesis.

    Science.gov (United States)

    Rouiss, H; Bakry, F; Froelicher, Y; Navarro, L; Aleza, P; Ollitrault, P

    2018-03-05

    Two main types of triploid limes are produced worldwide. The 'Tahiti' lime type (Citrus latifolia) is predominant, while the 'Tanepao' type (C. aurantiifolia) is produced to a lesser extent. Both types result from natural interspecific hybridization involving a diploid gamete of C. aurantiifolia 'Mexican' lime type (itself a direct interspecific C. micrantha × C. medica hybrid). The meiotic behaviour of a doubled-diploid 'Mexican' lime, the interspecific micrantha/medica recombination and the resulting diploid gamete structures were analysed to investigate the possibility that 'Tahiti' and 'Tanepao' varieties are derived from natural interploid hybridization. A population of 85 tetraploid hybrids was established between a doubled-diploid clementine and a doubled-diploid 'Mexican' lime and used to infer the genotypes of 'Mexican' lime diploid gametes. Meiotic behaviour was studied through combined segregation analysis of 35 simple sequenbce repeat (SSR) and single nucleotide polymorphismn (SNP) markers covering the nine citrus chromosomes and cytogenetic studies. It was supplemented by pollen viability assessment. Pollen viability of the doubled-diploid Mexican lime (64 %) was much higher than that of the diploid. On average, 65 % of the chromosomes paired as bivalents and 31.4 % as tetravalents. Parental heterozygosity restitution ranged from 83 to 99 %. Disomic inheritance with high preferential pairing values was deduced for three chromosomes. Intermediate inheritances, with disomic trend, were found for five chromosomes, and an intermediate inheritance was observed for one chromosome. The average effective interspecific recombination rate was low (1.2 cM Mb-1). The doubled-diploid 'Mexican' lime had predominantly disomic segregation, producing interspecific diploid gamete structures with high C. medica/C. micrantha heterozygosity, compatible with the phylogenomic structures of triploid C. latifolia and C. aurantiifolia varieties. This disomic trend limits

  11. Waterlike anomalies in a two-dimensional core-softened potential

    Science.gov (United States)

    Bordin, José Rafael; Barbosa, Marcia C.

    2018-02-01

    We investigate the structural, thermodynamic, and dynamic behavior of a two-dimensional (2D) core-corona system using Langevin dynamics simulations. The particles are modeled by employing a core-softened potential which exhibits waterlike anomalies in three dimensions. In previous studies in a quasi-2D system a new region in the pressure versus temperature phase diagram of structural anomalies was observed. Here we show that for the two-dimensional case two regions in the pressure versus temperature phase diagram with structural, density, and diffusion anomalies are observed. Our findings indicate that, while the anomalous region at lower densities is due the competition between the two length scales in the potential at higher densities, the anomalous region is related to the reentrance of the melting line.

  12. Dynamic Softening or Stiffening a Supramolecular Hydrogel by Ultraviolet or Near-Infrared Light.

    Science.gov (United States)

    Zheng, Zhao; Hu, Jingjing; Wang, Hui; Huang, Junlin; Yu, Yihua; Zhang, Qiang; Cheng, Yiyun

    2017-07-26

    The development of light-responsive hydrogels that exhibit switchable size and mechanical properties with temporal and spatial resolution is of great importance in many fields. However, it remains challenging to prepare smart hydrogels that dramatically change their properties in response to both ultraviolet (UV) and near-infrared (NIR) lights. Here, we designed a dual-light responsive supramolecular gel by integrating UV light-switchable host-guest recognition, temperature responsiveness, and NIR photothermal ability in the gel. The gel could rapidly self-heal and is capable of both softening and stiffening controlled by UV and NIR lights, respectively. Besides stiffness modulation, the bending direction of the gel can be controlled by UV or NIR light irradiation. The smart gel makes it possible to generate dynamic materials that respond to both UV and NIR lights and represents a useful tool that might be used to modulate cellular microenvironments with spatiotemporal resolution.

  13. Cloud fluid compression and softening in spiral arms and the formation of giant molecular cloud complexes

    International Nuclear Information System (INIS)

    Cowie, L.L.

    1981-01-01

    In this, the second paper of a series on the galactodynamics of the cloudy interstellar medium, we consider the response of such a gas to a forcing potential in the tight-winding density wave theory. The cloud fluid is treated in the hydrodynamic limit with an equation of state which softens at high densities. It is shown that in the inner regions of the galaxy, cooling of the cloud fluid in the arms can result in gravitational instability and the formation of large bound complexes of clouds which we identify with the giant molecular clouds (GMCs). Masses dimensions, distributions, and scale heights of the GMCs are predicted by the theory. It is suggested that the interstellar gas density in the disk is regulated by the gravitational instability mechanism in the arms which siphons material into star formation. Implications for the evolution of individual GMCs and for galactic morphology are discussed

  14. Bandwidth broadening and asymmetric softening of collective spin waves in magnonic crystals

    International Nuclear Information System (INIS)

    Montoncello, F.; Giovannini, L.

    2014-01-01

    We investigate the dependence on the applied field of the frequency/wavevector dispersion relations of collective spin waves in arrays of dots, close to a magnetic transition. In particular, we focus on the low frequency “soft” modes in three different cases: end modes in the transition between two different saturated states in ellipses, fundamental mode in the saturated-to-vortex transition in disks, and gyrotropic mode in the vortex-to-saturated transition in disks. Noteworthy, the spin waves with nonzero Bloch wavevector along the direction of the applied field happen to soften earlier than spin waves with a Bloch wavevector along different directions, and this feature is responsible for an asymmetric broadening of the bandwidth along the different lattice directions. This is particularly useful in magnonic/spin-logic device research, if different binary digits are associated to modes with the same cell function but different propagation directions.

  15. Phase-change materials: vibrational softening upon crystallization and its impact on thermal properties

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, Toshiyuki [Materials Science and Analysis Technology Centre, Panasonic Corporation, Osaka (Japan); Japan Synchrotron Radiation Research Institute Hyogo (Japan); Yamada, Noboru [Digital and Network Technology Development Centre, Panasonic Corporation, Osaka (Japan); Japan Synchrotron Radiation Research Institute Hyogo (Japan); Kojima, Rie [Digital and Network Technology Development Centre, Panasonic Corporation, Osaka (Japan); Shamoto, Shinichi [Neutron Science Research Centre, Japan Atomic Energy Research Institute, Ibaraki (Japan); Sato, Masugu; Tanida, Hajime; Uruga, Tomoya; Kohara, Shinji [Japan Synchrotron Radiation Research Institute, Hyogo (Japan); Takata, Masaki [SPring-8/RIKEN, Hyogo, Japan, Department of Advanced Materials Science, School of Frontier Sciences, The University of Tokyo, Chiba (Japan); Zalden, Peter; Bruns, Gunnar; Wuttig, Matthias [I. Physikalisches Institut und JARA-FIT, RWTH Aachen Univ. (Germany); Sergueev, Ilya [European Synchrotron Radiation Facility, Grenoble (France); Wille, Hans Christian [Deutsches Elektronen-Synchrotron, Hamburg (Germany); Hermann, Raphael Pierre [Juelich Centre for Neutron Science JCNS and Peter Gruenberg, Institut PGI, JARA-FIT, Forschungszentrum Juelich GmbH (Germany); Faculte des Sciences, Universite de Liege (Belgium)

    2011-06-21

    Crystallization of an amorphous solid is usually accompanied by a significant change of transport properties, such as an increase in thermal and electrical conductivity. This fact underlines the importance of crystalline order for the transport of charge and heat. Phase-change materials, however, reveal a remarkably low thermal conductivity in the crystalline state. The small change in this conductivity upon crystallization points to unique lattice properties. The present investigation reveals that the thermal properties of the amorphous and crystalline state of phase-change materials show remarkable differences such as higher thermal displacements and a more pronounced anharmonic behavior in the crystalline phase. These findings are related to the change of bonding upon crystallization, which leads to an increase of the sound velocity and a softening of the optical phonon modes at the same time. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  16. Improved actuation strain of PDMS-based DEA materials chemically modified with softening agents

    Science.gov (United States)

    Biedermann, Miriam; Blümke, Martin; Wegener, Michael; Krüger, Hartmut

    2015-04-01

    Dielectric elastomer actuators (DEAs) are smart materials that gained much in interest particularly in recent years. One active field of research is the improvement of their properties by modification of their structural framework. The object of this work is to improve the actuation properties of polydimethylsiloxane (PDMS)-based DEAs by covalent incorporation of mono-vinyl-terminated low-molecular PDMS chains into the PDMS network. These low-molecular units act as a kind of softener within the PDMS network. The loose chain ends interfere with the network formation and lower the network's density. PDMS films with up to 50wt% of low-molecular PDMS additives were manufactured and the chemical, mechanical, electrical, and electromechanical properties of these novel materials were investigated.

  17. Stress-Strain Law for Confined Concrete with Hardening or Softening Behavior

    Directory of Open Access Journals (Sweden)

    Piero Colajanni

    2013-01-01

    Full Text Available This paper provides a new general stress-strain law for concrete confined by steel, fiber reinforced polymer (FRP, or fiber reinforced cementitious matrix (FRCM, obtained by a suitable modification of the well-known Sargin’s curve for steel confined concrete. The proposed law is able to reproduce stress-strain curve of any shape, having both hardening or softening behavior, by using a single closed-form simple algebraic expression with constant coefficients. The coefficients are defined on the basis of the stress and the tangent modulus of the confined concrete in three characteristic points of the curve, thus being related to physical meaningful parameters. It will be shown that if the values of the parameters of the law are deduced from experimental tests, the model is able to accurately reproduce the experimental curve. If they are evaluated on the basis of an analysis-oriented model, the proposed model provides a handy equivalent design model.

  18. Experimental model for neutron scattering in disordered systems: static structure factor determination of mode-softening

    International Nuclear Information System (INIS)

    Siegel, E.

    1982-01-01

    The generalized-disorder collective-boson mode-softening universality-principle (GDCBMSUP) for collective-boson mode dispersion in disordered systems (liquids, quantum liquids, glasses, powders, disordered magnets, plasmas...), a unified qualitative and semi-qualitative and semi-quantitative descriptive prescription for treating the properties of very differently disordered systems, is directly dependent upon a measurement (or calculation) of the static structure factor S(k) determined from a frequency average of the dynamic structure factor S(k,w), a multiple of the inelastic differential neutron scattering cross section d 2 sigma/dwdOMEGA. The prescription for this principle is given and, because of its universal applicability to disordered systems of any type with any type and/or degree of disorder, the neutron scattering determination of S(k) takes on renewed importance

  19. [Effects of Lime on Seedling Growth,Yield and Volatile Constituents of Atractylodes lancea].

    Science.gov (United States)

    Zhang, Yan; Miki, Sakurai; Chen, Mei-lan; Takeda, Xiuji; Zhao, Dong-yue; Kang, Li-ping; Guo, Lan-ping

    2015-03-01

    To investigate the effects of different amounts of lime on yield and quality of Atractylodes lancea, and to provide reference for the herb growing site soil improvement and self-poisoning ease. Add different gradients of lime, and then measure their growth targets, yield and four kinds of volatile constituents content(hinesol, atractylone, β-eudesmol and atractylodin). Volatile constituents yield per plant was calculated. Adding 160 g/m2 lime had a significant role in promoting the growth and yield of herb; Adding 80 g/m2 lime was conducive to the volatile constituents production, and adding lime decreased the atractylone and atractylodin content, while increased the hinesol and β-eudesmol content; Adding 160 g/m2 lime promoted the volatile constituents yield per plant. Adding lime plays a role of neutralize soil pH, antibacteria and prevention incognita, and has a certain degree of ease autotoxicity and obstacle,and then promotes the yield and volatile constituents production of Atractylodes lancea.

  20. Effects of Palm Kernel Shell Ash on Lime-Stabilized Lateritic Soil

    Science.gov (United States)

    Nnochiri, Emeka Segun; Ogundipe, Olumide M.; Oluwatuyi, Opeyemi E.

    2017-09-01

    The research investigated the effects of palm kernel shell ash (PKSA) on lime-stabilized lateritic soil. Preliminary tests were performed on three soil samples, i.e., L1, L2 and L3 for identification; the results showed that L1 was A-7-6, L2 was A-7-6, and L3 was A-7-6. The optimum amount of lime for each of the soil samples was achieved. The optimum amount for L1 was 10%, for L2, 8% and for L3, 10%; at these values they recorded the lowest plasticity indexes. The further addition of PKSA was performed by varying the amount of PKSA and lime added to each of the soil samples. The addition of 4% PKSA+ 6% lime, the addition of 4% PKSA + 4% lime, and the addition of 4% PKSA + 6% lime increased the California Bearing Ratio (CBR) to the highest values for L1, L2 and L3 from 8.20%. It was concluded that PKSA can be a suitable complement for lime stabilization in lateritic soil.

  1. Effect of Lime on characteristics of consolidation, strength, swelling and plasticity of fine grained soil

    Science.gov (United States)

    Estabragh, A. R.; Bordbar, A. T.; Parsaee, B.; Eskandari, Gh.

    2009-04-01

    Using Lime as an additive material to clayey soil is one of the best effective technique in building the soil structures to get some purposes such as soil stabilization, soil reinforcement and decreasing soil swelling. In this research the effect of Lime on geotechnical characteristics of a clayey soil was investigated. Soil specimen types used in this study were consisted of clayey soil as the control treatment and clay mixed with different weight fractions of lime, 4, 6, 8 & 10 percent. Some experiments such as CBR, atterburg limits, compaction, consolidation and swelling was conducted on specimens. Results revealed that adding lime to soil would change its physical and mechanical properties. Adding lime increase the compression strength and consolidation coefficient and decrease swelling potential and maximum dry density. According to the results, Atterburg experiments show that presence of lime in soil increase the liquid limit of low plasticity soil and decrease the liquid limit of high plasticity soil, but totally it decreases the plasticity index of soils. Key words: soil stabilization, lime, compression strength, swelling, atterburg limits, compaction

  2. Acid-base properties of a limed pyritic overburden during simulated weathering

    Energy Technology Data Exchange (ETDEWEB)

    Doolittle, J.J.; Hossner, L.R. [South Dakota State University, Brookings, SD (United States). Plant Science Dept.

    1997-11-01

    Surface-mine reclamation is often hindered by the formation of acid mine soil and acid mine drainage from FeS{sub 2} oxidation. Surface soils containing FeS{sub 2} are often treated with crushed limestone (predominately CaCO{sub 3}) to prevent aid minesoil formation. The main objective of this study was to evaluate the long-term effectiveness of liming pyritic minesoil to prevent the formation of acid minesoil and acid mine drainage. Pyritic minesoils that did not receive lime became acidic very rapidly and produced acidic leachate. Almost all of the FeS{sub 2} in this treatment oxidized during the first 200 d. The addition of lime at a rate of 25% of the theoretical acid-base account (ABA) significantly slowed FeS{sub 2} oxidation, but rapid oxidation ensued after the added lime was neutralized. Treatments receiving a liming rate of 50% ABA or greater remained neutral to alkaline throughout the study. Acid-base values and residual FeS{sub 2}-CO{sub 3} data, however, indicate that the lime was dissolving from the system faster than the FeS{sub 2} was oxidizing, and all the treatments would eventually become acidic. The results indicate that the liming of a pyritic overburden to an ABA of 125% is not a sustainable solution to preventing acid minesoil and acid mine drainage. 25 refs., 6 figs., 3 tabs.

  3. A study on engineering characteristics of asphalt concrete using filler with recycled waste lime.

    Science.gov (United States)

    Sung Do, Hwang; Hee Mun, Park; Suk keun, Rhee

    2008-01-01

    This study focuses on determining the engineering characteristics of asphalt concrete using mineral fillers with recycled waste lime, which is a by-product of the production of soda ash (Na(2)CO(3)). The materials tested in this study were made using a 25%, 50%, 75%, and 100% mixing ratio based on the conventional mineral filler ratio to analyze the possibility of using recycled waste lime. The asphalt concretes, made of recycled waste lime, hydrated lime, and conventional asphalt concrete, were evaluated through their fundamental engineering properties such as Marshall stability, indirect tensile strength, resilient modulus, permanent deformation characteristics, moisture susceptibility, and fatigue resistance. The results indicate that the application of recycled waste lime as mineral filler improves the permanent deformation characteristics, stiffness and fatigue endurance of asphalt concrete at the wide range of temperatures. It was also determined that the mixtures with recycled waste lime showed higher resistance against stripping than conventional asphalt concrete. It was concluded from various test results that a waste lime can be used as mineral filler and, especially, can greatly improve the resistance of asphalt concrete to permanent deformation at high temperatures.

  4. A systematic review of the effectiveness of liming to mitigate impacts of river acidification on fish and macro-invertebrates

    International Nuclear Information System (INIS)

    Mant, Rebecca C.; Jones, David L.; Reynolds, Brian; Ormerod, Steve J.; Pullin, Andrew S.

    2013-01-01

    The addition of calcium carbonate to catchments or watercourses – liming – has been used widely to mitigate freshwater acidification but the abatement of acidifying emissions has led to questions about its effectiveness and necessity. We conducted a systematic review and meta-analysis of the impact of liming streams and rivers on two key groups of river organisms: fish and invertebrates. On average, liming increased the abundance and richness of acid-sensitive invertebrates and increased overall fish abundance, but benefits were variable and not guaranteed in all rivers. Where B-A-C-I designs (before-after-control-impact) were used to reduce bias, there was evidence that liming decreased overall invertebrate abundance. This systematic review indicates that liming has the potential to mitigate the symptoms of acidification in some instances, but effects are mixed. Future studies should use robust designs to isolate recovery due to liming from decreasing acid deposition, and assess factors affecting liming outcomes. -- Highlights: •In a systematic review and meta-analysis, we asked how river liming affected fish and invertebrates. •On average, liming increased fish abundance. •Liming also increased average abundance and richness of acid-sensitive invertebrates. •However, benefits were variable and not guaranteed in all acidified rivers. -- A systematic review showed lime application to acidified rivers increased average fish abundance, and abundance and richness in acid-sensitive invertebrates, but not always

  5. Long-term field-scale experiment on using lime filters in an agricultural catchment.

    Science.gov (United States)

    Kirkkala, Teija; Ventelä, Anne-Mari; Tarvainen, Marjo

    2012-01-01

    The River Yläneenjoki catchment in southwest Finland is an area with a high agricultural nutrient load. We report here on the nutrient removal performance of three on-site lime-sand filters (F1, F2, and F3), established within or on the edge of the buffer zones. The filters contain burnt lime (CaO) or spent lime [CaO, Ca(OH), and CaCO]. Easily soluble lime results in a high pH level (>11) and leads to an efficient precipitation of soluble phosphorus (P) from the runoff. Water samples were taken from the inflow and outflow of each site in different hydrological situations. The length of the monitoring period was 4 yr for F1, 6 yr for F2, and 1.5 yr for F3. F1 and F2 significantly reduced the suspended solids (SS), total P (PTOT), and dissolved reactive P (DRP) in the treated water. The proportional reduction (%) varied but was usually clearly positive. Filter F3 was divided into two equal parts, one containing burnt lime and the other spent lime. Both filter parts removed PTOT and SS efficiently from the water; the burnt-lime part also removed DRP. The mixed-lime part removed DRP for a year, but then the efficiency decreased. The effect of filters on nitrogen compounds varied. We conclude that sand filters incorporating lime can be used together with buffer zones to reduce both P and SS load to watercourses. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  6. Admixture of lime in connection with deep rotary cultivation for short rotation energy forest

    Energy Technology Data Exchange (ETDEWEB)

    Danfors, B; Stambeck, A; Aasberg, G

    1985-01-01

    Spaghnum soils, which could be used for production of short rotation energy forests (Salix), require lime for the adjustment of the pH-level to obtain production at acceptable levels. It is necessary that the lime is distributed uniformly in the soil profile to a depth of at least 40-50 cm. The investigation has studied three methods of spreading and incorporating lime in the uppermost layer of soil. The first method concerned ploughing of peat soil with a conventional agricultural plough, the second method concerned rotovation with an agricutural rotovator to maximally 20 cm depth. In both cases the lime has been spread with a centrifugal broadcaster before the soil tillage. The third method implied simultaneous spreading of the lime and rotovation of the peat to a depth of maximally 50 cm, JTI has built and constructed a machine for this purpose. Ploughing as the only method of soil tillage of peat soils before planting of short rotation energy forests is rejected for two reasons. 1. Certain peat soils which have such mechanical properties that they immediately completely clog a plough. 2. The deficient distribution of lime in the ploughed layer. Rotovation with an agricultural rotovator has been done with good results. The delivery of lime in connection with the rotovation works well provided that the lime is dry. The peat is efficiently disintegrated and the lime gets a sufficiently uniform admixture. The cultivation depth, 40-50 cm, appears to be sufficient for the Salix plants to cope with the water supply during the summer. Limitations which should be discussed concern the cost of such an intensive and deep tillage of the peat.

  7. Nutrient leaching potential following application of papermill lime-sludge to an acidic clay soil

    Directory of Open Access Journals (Sweden)

    S. C. Vettorazzo

    2001-09-01

    Full Text Available This experiment was carried out under greenhouse conditions with soil pots during 210 days, to evaluate the effect of calcitic papermill lime-sludge application (at the rates 0, 773, 1.547, and 2.320 mg kg-1 or respective equivalents to control, 2, 4, and 6 t ha-1, on chemical composition of soil leachate and its effects on eucalypt growth and yield. Highest soil leachate pH, SO4, and Na concentrations occurred in the 4 and 6 t ha-1 treatments. Soil leachate nitrate concentrations decreased with increasing lime-sludge rate. Soil leachate phosphate remained low (below the detection limit in all treatments until 120 days, while the concentration increased in the lime-sludge treatments at 210 days (last sampling in about 600 mg L-1. Lime-sludge decreased leachate Mg concentration, but had no significant effect among rates. Soil leachate Ca, K, B, Cu, Fe, and Zn did not change significantly for any lime-sludge application rates. The maximum NO3, Ca, Mg, K, and Na concentrations in the soil leachate occurred at 60 days after lime-sludge application (leaching equivalent to 1 pore volume, but for pH and SO4, the maximum occurred at 210 days (leaching equivalent to 4 pore volumes. Lime-sludge application decreased the concentration of exchangeable Al in the soil. Plant diameter growth and dry matter yield were increased with increasing lime-sludge rate. Beneficial effects on mineral nutrition (P, K, Ca, B, and Zn of eucalypts were also obtained by the application of 4 and 6 t ha-1 of lime-sludge.

  8. DNA markers provide insight about common lime in historicalplantings

    DEFF Research Database (Denmark)

    Hansen, Ole Kim; Thomsen, Pernille; Rasmussen, Christine Waage

    2014-01-01

    As part of the restoration process of an avenue of common lime (Tilia × europaea) from 1760 in the Royal Danish Gardens, all remaining trees were genotyped with DNA markers before they were felled. As such, information about the nature of the plant material (clonal versus non-clonal) and mode...... of propagation was obtained, revealing that a single clone constituted 92% of the remaining trees (106 out of 115). Five trees were of another clone, while the remaining four trees had unique genotypes. Mode of clonal propagation was most likely layering since the genotype of the crown and the roots...... of a subsample of the trees had the same genotype. Trees from four other locations with historical avenues/plantings from the 17th century were also genotyped. The two clones registered in the first location were also found at the other four locations. Of 76 trees from the other historical avenues...

  9. Methods and systems for utilizing carbide lime or slag

    Science.gov (United States)

    Devenney, Martin; Fernandez, Miguel; Chen, Irvin; Calas, Guillaume; Weiss, Michael Joseph; Tester, Chantel Cabrera

    2018-02-27

    Provided herein are methods comprising a) treating a slag solid or carbide lime suspension with an ammonium salt in water to produce an aqueous solution comprising calcium salt, ammonium salt, and solids; b) contacting the aqueous solution with carbon dioxide from an industrial process under one or more precipitation conditions to produce a precipitation material comprising calcium carbonate and a supernatant aqueous solution wherein the precipitation material and the supernatant aqueous solution comprise residual ammonium salt; and c) removing and optionally recovering ammonia and/or ammonium salt using one or more steps of (i) recovering a gas exhaust stream comprising ammonia during the treating and/or the contacting step; (ii) recovering the residual ammonium salt from the supernatant aqueous solution; and (iii) removing and optionally recovering the residual ammonium salt from the precipitation material.

  10. Luminescence quartz dating of lime mortars. A first research approach

    International Nuclear Information System (INIS)

    Zacharias, N.; Mauz, B.; Michael, C.T.

    2002-01-01

    Lime mortars mixed with sand are well suited for connecting structural materials, like stones and bricks, due to the mechanical properties this material exhibits. Their extensive use in architectural and decorative works during the last 4000 years motivated the introduction of the 'Luminescence clock' for age determination of mortars. The same principles as for quartz optically stimulated luminescence (OSL) dating of sediments were applied for age estimation of a mortar fragment removed from a Byzantine church monument dated by archaeological means to 1050-1100 years ago (the first half of the 10th century). The OSL from the quartz was monitored under blue light stimulation and UV detection, using a single-aliquot-regenerative-dose protocol. The quartz-OSL dating of the mortar resulted in 870±230 a. TL polymineral fine grain dating was also performed on a brick fragment which was connected to the mortar, resulting in a TL age of 1095±190 a. (author)

  11. Genetic variation assessment of acid lime accessions collected from south of Iran using SSR and ISSR molecular markers.

    Science.gov (United States)

    Sharafi, Ata Allah; Abkenar, Asad Asadi; Sharafi, Ali; Masaeli, Mohammad

    2016-01-01

    Iran has a long history of acid lime cultivation and propagation. In this study, genetic variation in 28 acid lime accessions from five regions of south of Iran, and their relatedness with other 19 citrus cultivars were analyzed using Simple Sequence Repeat (SSR) and Inter-Simple Sequence Repeat (ISSR) molecular markers. Nine primers for SSR and nine ISSR primers were used for allele scoring. In total, 49 SSR and 131 ISSR polymorphic alleles were detected. Cluster analysis of SSR and ISSR data showed that most of the acid lime accessions (19 genotypes) have hybrid origin and genetically distance with nucellar of Mexican lime (9 genotypes). As nucellar of Mexican lime are susceptible to phytoplasma, these acid lime genotypes can be used to evaluate their tolerance against biotic constricts like lime "witches' broom disease".

  12. Strengthening Masonry Arches with Lime-Based Mortar Composite

    Directory of Open Access Journals (Sweden)

    Valerio Alecci

    2017-06-01

    Full Text Available In recent decades, many strengthening interventions on masonry elements were performed by using fiber reinforced polymers (FRPs. These advanced materials proved to be effective to increase the load-carrying capacity of masonry elements and to improve their structural behavior, avoiding the most critical failure modes. Despite the advantages of this technique compared to more traditional methods, FRP systems have disadvantages related to their low resistance to high temperatures, impossibility of application on wet surfaces, low permeability, and poor compatibility with masonry supports. Therefore, composite materials made of a fiber textile embedded in an inorganic matrix were recently proposed as alternatives to FRPs for strengthening historic masonry constructions. These composite materials are easier to install, have higher resistance to high temperatures, and permit higher vapor permeability than FRPs. The inorganic matrix is frequently a cement-based mortar, and the composite materials made of a fiber textile embedded in a cement-based mortar are usually identified as FRCM (fabric reinforced cementitious matrix composites. More recently, the use of natural lime mortar as an inorganic matrix has been proposed as an alternative to cement-based mortars when historic compatibility with the substrate is strictly required, as in case of restoration of historic buildings. In this paper, the effectiveness of a fabric made of basalt fibers embedded in lime mortar matrix (Basalt-FRLM for the strengthening of masonry arches is investigated. An experimental investigation was performed on 1:2 scaled brick masonry arches strengthened at the extrados with a layer of Basalt-FRLM and tested under vertical load. The results obtained are compared with previous results obtained by the authors by testing masonry arches strengthened at their extrados with FRCM and FRP composites. This investigation highlights the effectiveness of Basalt-FRLM in increasing load

  13. Development of soda-lime glasses from ornamental rock wastes

    International Nuclear Information System (INIS)

    Babisk, Michelle Pereira

    2009-01-01

    During the ornamental rocks production, among other steps, one saw the rock blocks in order to transform them into semi-finished plates. In this step, expressive amounts of residues are generated, which are not properly discharged in nature, without any programmed utilization. The residues of silicide rocks present, in their compositions, oxides which are raw materials employed to fabricate soda-lime type glasses (containing SiO_2, Al_2O_3, CaO, Na_2O and K_2O). On the other hand the residues of carbonatic rocks are constituted of glass net modifier oxides, like CaO and MgO. In this work it was developed four types of soda-lime glasses using ornamental rock residues, where the glasses compositions were adjusted by adding sand, as silica source, as well as sodium and calcium carbonates as sources of Na_2O and CaO, respectively. The obtained glasses were characterized by means of Archimed's method for densities measurements, microstructure by using optical and electronic microscopy, phases by means of X-ray diffraction (XRD), hardness by Vickers indentation, spectroscopy (UV/VIS), and hydrolytic resistance according to ISO 719. The XRD analyses confirmed the compositions total vitrification, where the greened aspect of the samples was due to the presence of the iron oxides. The produced glasses properties were compared with those of commercial glasses aiming their industrial employment. The main difference between the produced glasses and those commercials varied primarily regarding the amount of carbonates incorporated. The results showed that the ornamental rocks residues may be used as raw materials for glasses fabrication, and they found a useful economic destination rather than discharge which promotes undesirable environmental impact. (author)

  14. Studies on the effect of gamma irradiation on shelf life of Kagzi lime (Citrus aurantifolia swingle)

    International Nuclear Information System (INIS)

    Pandey, S.K.; Bisen, A.

    2006-01-01

    Influence of irradiation on shelf life of Kagzi lime fruits were studied. The results revealed that most of the physical and chemical parameters of fruits were significantly influenced by 100 Gy gamma radiation up to 22 days without affecting fruit quality. Higher doses of gamma irradiation (> 200 Gy) deteriorated the fruit quality and organoleptic parameters of the fruit. Thus, irradiation of lime fruits with 100 Gy gamma radiation extended shelf life of lime fruits and also helps in maintaining the chemical constituents viz., T.S.S. Acidity, Vitamin C, pH and juice content. (author)

  15. Microbial communities associated with the anthropogenic, highly alkaline environment of a saline soda lime, Poland

    OpenAIRE

    Kalwasi?ska, Agnieszka; Felf?ldi, Tam?s; Szab?, Attila; Deja-Sikora, Edyta; Kosobucki, Przemys?aw; Walczak, Maciej

    2017-01-01

    Soda lime is a by-product of the Solvay soda process for the production of sodium carbonate from limestone and sodium chloride. Due to a high salt concentration and alkaline pH, the lime is considered as a potential habitat of haloalkaliphilic and haloalkalitolerant microbial communities. This artificial and unique environment is nutrient-poor and devoid of vegetation, due in part to semi-arid, saline and alkaline conditions. Samples taken from the surface layer of the lime and from the depth...

  16. Twenty years of experience with central softening in The Netherlands : Water quality – Environmental benefits – Costs

    NARCIS (Netherlands)

    Hofman, J.A.M.H.; Kramer, O.J.I.; van der Hoek, J.P.; Nederlof, M; Groenendijk, M

    2006-01-01

    Central softening has been utilized by the Dutch water utilities since the late 1970s. It was introduced in the water treatment process as a method to supply water with an optimum water composition to prevent lead and copper release and to prevent excessive scaling. Twenty years of experience show

  17. Effects of Nitrogen Content on the HAZ Softening of Ti-Containing High Strength Steels Manufactured by Accelerated Cooling

    Energy Technology Data Exchange (ETDEWEB)

    Bang, Kook-soo; Jung, Ho-shin; Park, Chan [Pukyong National University, Busan (Korea, Republic of)

    2017-03-15

    The effects of nitrogen content on the HAZ softening of Ti-containing high strength steels manufactured by accelerating cooling were investigated and interpreted in terms of the microstructures in the softening zone. Regardless of their content, all of the steels investigated showed a softened zone 9-10 mm wide. The minimum hardness in the zone, however, was different, with lower hardness in the higher nitrogen content steel. Microstructural observations of the steel showed that the amount of soft ferrite was increased in the zone with an increase of nitrogen content of the steel, suggesting that microstructural evolution in the HAZ is influenced by the nitrogen content. Measurements of TiN particles showed that the degree of particles coarsening in the HAZ was lower in the higher nitrogen content steel. Therefore, it is believed that finer TiN particles in the HAZ inhibit austenite grain growth more effectively, and lead to an accelerated ferrite transformation in higher nitrogen content steel, resulting in a higher amount of soft ferrite microstructure in the softened zone.

  18. Influence of Softening Temperature of Azobenzene Polymers and External Electric Field on Diffraction Efficiency of Polarization Holograms

    Directory of Open Access Journals (Sweden)

    Nicolay Davidenko

    2017-12-01

    Full Text Available Growth of the diffraction efficiency and recording velocity was found in the films of copolymers 4-((2- nitrophenyl diazeniylphenylmethacrylate with octylmethacrylate at room temperature holographic recording for copolymer with less softening temperature. Effect of strengthening of the diffraction efficiency was observed when charging surface of the films with recorded hologram in crown discharge.

  19. Thermochemical transformations of hard-coal pitches at the stage of raising the softening temperature to 358-363 K

    Energy Technology Data Exchange (ETDEWEB)

    Kekin, N.A.; Belkina, T.V.; Stepanenko, M.A.; Gordienko, V.G.

    1983-01-01

    Using high-resolution NMR together with infra-red spectroscopy, data were obtained characterising changes in hydrogen content in various groups of compounds dissolved in fractions of the original pitch and its thermal product when raising the softening temperature to 358-363 K.

  20. INFLUENCE OF LIMING AND WASTE ORGANIC MATERIALS ON THE ACTIVITY OF PHOSPHATASE IN SOIL CONTAMINATED WITH NICKEL

    Directory of Open Access Journals (Sweden)

    Beata Kuziemska

    2014-10-01

    Full Text Available A study was carried out on soil following a two-year pot experiment that was conducted in 2009–2010, in three repetitions in Siedlce. The experiment included the following factors: 1 – amount of Ni in soil (0, 75, 150 and 225 mg·kg-1 soil by applying an aqueous NiSO4·7H2O solution; 2 – liming (0 and Ca according to 1 Hh as CaCO3; 3 – organic waste products (rye straw at a dose of 4 t·ha-1 and brown coal at a dose of 40 t·ha-1. In each experimental year, orchard grass was the test plant and four swaths were harvested. The activities of acidic and alkaline phosphatase, pH and the content of carbon in organic compounds were determined in the soil samples collected after each grass swath and in each experimental year. It was found that Ni at 75 mg·kg-1 soil activated the enzymes under study, whereas higher doses caused their statistically-confirmed inactivation. The lowest activity of the investigated enzymes was detected in soil supplemented with 225 Ni·kg-1 soil. Liming caused an increase in the activity of alkaline phosphatase and a reduction in the activity of acidic phosphatase. Straw and brown coal induced a substantial increase in the activity of both enzymes in the tested soil samples. Both liming and straw and carbon eliminated the negative effect of higher nickel doses on the activity of the enzymes under study.

  1. Use of coal fly ash and other waste products in soil stabilization and road construction-including non-destructive testing of roadways.

    Science.gov (United States)

    2012-02-01

    An extensive laboratory testing program was performed on subgrade soils stabilized using fly ash and lime kiln dust. The laboratory : program included measurements of: compaction curves, small strain elastic moduli, resilient modulus (Mr), Briaud Com...

  2. Use of coal fly ash and other waste products in soil stabilization and road construction including non-destructive testing of roadways.

    Science.gov (United States)

    2012-06-01

    An extensive laboratory testing program was performed on subgrade soils stabilized using fly ash and : lime kiln dust. The laboratory program included measurements of: compaction curves, small strain elastic moduli, : resilient modulus (Mr), Briaud C...

  3. Effects of Crop Straw Returning with Lime on Activity of Cu, Zn, Pb and Cd in Paddy Soil

    Directory of Open Access Journals (Sweden)

    NI Zhong-ying

    2017-05-01

    Full Text Available Crop straw returning is an important measure for increasing soil carbon fixation and soil fertility in China, but it also may result in some risk of raising activity of heavy metals in the soil. In order to understand the effects of different sources of crop straw on heavy metals activity in soil with different pollution levels, and to take appropriate measures to prevent the activation of heavy metals in the soil, both pot and field experiments were carried out to study the effects of crop straw returning with lime on activity of Cu, Zn, Pb and Cd in paddy soil. The experiments were carried out in the soils with both light and heavy pollution of heavy metals. In the pot experiment, three straws, including rice straw with heavy pollution of heavy metals, rice straw with light pollution of heavy metals, and rape straw with light pollution of heavy metals, were tested. Two dosages of lime(0 kg·hm-2 and 750 kg·hm-2were applied. Field experiment had three treatments, ie., control without application of straw and lime, straw returning and straw returning + lime. Soil available heavy metals, accumulation of heavy metals in rice grain, and chemical forms of soil heavy metals were dynamical monitored. The results showed that crop straw returning increased significantly the concentrations of dissolved organic carbon and water soluble heavy metals in paddy soils at the early stage of experiment (in first 20 days. The increase in water soluble heavy metals in the soil with heavy pollution of heavy metals was most obvious as compared with the control treatment. After 60th day of the experiment, the effects of straw returning on the activity of heavy metals in the soil decreased gradually with the time, and became no obvious. The concentrations of water soluble heavy metals in the soil treated with rape straw was generally lower than that of rice straw, while those in the soil treated with heavy pollution of rice straw was higher than low pollution of rice

  4. Influence of lime on struvite formation and nitrogen conservation during food waste composting.

    Science.gov (United States)

    Wang, Xuan; Selvam, Ammaiyappan; Wong, Jonathan W C

    2016-10-01

    This study aimed at investigating the feasibility of supplementing lime with struvite salts to reduce ammonia emission and salinity consequently to accelerate the compost maturity. Composting was performed in 20-L bench-scale reactors for 35days using artificial food waste mixed with sawdust at 1.2:1 (w/w dry basis), and Mg and P salts (MgO and K2HPO4, respectively). Nitrogen loss was significantly reduced from 44.3% to 27.4% during composting through struvite formation even with the addition of lime. Lime addition significantly reduced the salinity to less than 4mS/cm with a positive effect on improving compost maturity. Thus addition of both lime and struvite salts synergistically provide advantages to buffer the pH, reduce ammonia emission and salinity, and accelerate food waste composting. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Separation of hemicellulose-derived saccharides from wood hydrolysate by lime and ion exchange resin.

    Science.gov (United States)

    Wang, Xiaojun; Zhuang, Jingshun; Fu, Yingjuan; Tian, Guoyu; Wang, Zhaojiang; Qin, Menghua

    2016-04-01

    A combined process of lime treatment and mixed bed ion exchange was proposed to separate hemicellulose-derived saccharides (HDS) from prehydrolysis liquor (PHL) of lignocellulose as value added products. The optimization of lime treatment achieved up to 44.2% removal of non-saccharide organic compounds (NSOC), mainly colloidal substances, with negligible HDS degradation at 0.5% lime level and subsequent neutralization by phosphoric acid. The residual NSOC and calcium ions in lime-treated PHL were eliminated by mixed bed ion exchange. The breakthrough curves of HDS and NSOC showed selective retention toward NSOC, leading to 75% HDS recovery with 95% purity at 17 bed volumes of exchange capacity. In addition, macroporous resin showed higher exchange capacity than gel resin as indicated by the triple processing volume. The remarkable selectivity of the combined process suggested the feasibility for HDS separation from PHL. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Hemp-Lime Performance in Danish Climatic Context. Thermal Conductivity as a Function of Moisture Content

    DEFF Research Database (Denmark)

    Antonov, Yovko Ivanov; Jensen, Rasmus Lund; Pomianowski, Michal Zbigniew

    2016-01-01

    concrete is a bio-based building material composed of the woody core of industrial hemp and lime based binder. It is a non-load-bearing material, which can be used as floor and around structural frames for walls and roof. The material is characterized by relatively low environmental impact, moderate...... thermal properties and, high air and moisture permeability. The properties vary with binder composition, mixing and casting techniques, as well as intended application. This research presents preliminary heat and moisture building simulations of single family house made out of hemp-lime composite....... To evaluate the performance of hemp-lime, it is compared to models with common external walls, upon defined parameters. The article also determines the variation of thermal conductivity for hemp-lime commercial plaster and wall mix, as a function of moisture content. The most promising binder composition...

  7. Thermophysical properties of enzyme clarified Lime (Citrus aurantifolia L) juice at different moisture contents.

    Science.gov (United States)

    Manjunatha, S S; Raju, P S; Bawa, A S

    2014-11-01

    Thermophysical properties of enzyme clarified lime (Citrus aurantifolia L.) juice were evaluated at different moisture contents ranging from 30.37 % to 89.30 % (wet basis) corresponding to a water activity range of 0.835 to 0.979. The thermophysical properties evaluated were density, Newtonian viscosity, thermal conductivity, specific heat and thermal diffusivity. The investigation showed that density and Newtonian viscosity of enzyme clarified lime juice decreased significantly (p lime juice with moisture content/water activity employing regression analysis by the method of least square approximation. Results indicated the existence of strong correlation between thermophysical properties and moisture content/water activity of enzyme clarified lime juice, a significant (p < 0.0001) negative correlation between physical and thermal properties was observed.

  8. Expansive soil stabilization with coir waste and lime for flexible pavement subgrade

    Science.gov (United States)

    Narendra Goud, G.; Hyma, A.; Shiva Chandra, V.; Sandhya Rani, R.

    2018-03-01

    Expansive soil properties can be improved by various methods to make it suitable for construction of flexible pavement. The coir pith is the by-product (bio-waste) generated from coir industry during extraction of coir fiber from coconut husk. Openly disposed coir pith can make the surrounding areas unhygienic. This bio-waste can be one of the potential materials to stabilize the expansive soils. In the present study coir pith and lime are used as stabilizers. Different combinations of coir pith contents (1%, 2% and 3%) and lime contents (2%, 3% and 4%)are used to study the behavior of expansive soil. Unconfined compressive strength (UCS) of unstabilized and stabilized soils was determined. Optimum content of coir pith and lime are determined based on UCS of the soil. California bearing ratio of soil determined at optimum contents of coir pith and lime. Flexible pavement layer compositions for two levels of traffic using stabilized soil subgrade.

  9. Effects of Periwinkle Shell Ash on Lime-Stabilized Lateritic Soil ...

    African Journals Online (AJOL)

    ADOWIE PERE

    Keywords: atterberg limits, lateritic soil, lime stabilization, periwinkle shell ash .... specimen were prepared by carefully and completely ..... Fourth Edition. Canada: CENGAGE Learning. Holtz, RD; Kovacs, WD (1981). ... Potentials of Sugar cane.

  10. Effects of acid rain and liming on the enchytraeid fauna in forest soils

    International Nuclear Information System (INIS)

    Graefe, U.

    1989-01-01

    The development of the enchytraeid community has been observed in a Solling beech forest over a period of 11 years. Eight out of 18 formerly established species have disappeared in one decade. The connection to soil chemical changes due to atmospheric deposition is discussed. A comparison of adjoining beech and spruce stands revealed considerably lower species numbers under spruce. The community under beech is developing in the direction of the species community in the spruce stand. Liming affects changes in the dominance structure. Mesophilic species are favoured, acidophilic are repressed. In an oak-beech stand near Hamburg even the recolonization by previously absent species was observed. Liming experiments with 25, 50 and 100 dt CaCO 3 /ha showed decreasing total abundance of enchytraeids proportional to the amount of lime. Species number, diversity and evenness increased with lime treatments up to 50 dt/ha. (orig.)

  11. Effect of liming on the behaviour of 90Sr and 137Cs in a lake ecosystem

    International Nuclear Information System (INIS)

    Outola, Iisa; Rask, Martti

    2011-01-01

    Liming of lakes is considered one possible remedial action to reduce the accumulation of radionuclides into fish in the case of a radiological accident. These responses were tested in field conditions in a small acidified lake that was divided into two parts: one limed with CaCO 3 and the other half left as an unlimed control. The transfer of 90 Sr from water into fish decreased on average by 50% during the first year after liming. However, at the same time the 90 Sr concentration in water increased, reaching a maximum within 6 months after liming. Approximately 50% more 90 Sr was detected in water in the limed part of the lake than on control side during the first year. 90 Sr was most probably released from the sediment as the Ca concentration and pH of the water increased. As a result of these two processes, which counterbalanced each other (increased release of 90 Sr into water from sediment and decreased transfer of 90 Sr from water into fish), the 90 Sr concentration in fish did not notably differ between the limed and control sides of the lake. Liming may only be suitable as a remedial action if carried out immediately after a radiological accident, before significant amounts of radionuclides have been deposited in lake sediments. In the case of 137 Cs, the effect of liming was less pronounced. 137 Cs activity concentration in water increased in the first year by 20% and uptake by fish decreased by 20%. - Highlights: → Acidified lake was divided into two parts: one limed with CaCO 3 and the other half left as an unlimed control. → The transfer of 90 Sr from water into fish decreased by 50% during the first year after liming. → At the same time liming increased the 90 Sr concentration in the water by 50%. → The increased amount of 90 Sr in water is assumed to have originated from the lake sediments. → The 90 Sr concentration in fish remained relatively unchanged.

  12. Comparative study of the protein profiles of Sunki mandarin and Rangpur lime plants in response to water deficit.

    Science.gov (United States)

    Oliveira, Tahise M; da Silva, Fernanda R; Bonatto, Diego; Neves, Diana M; Morillon, Raphael; Maserti, Bianca E; Filho, Mauricio A Coelho; Costa, Marcio G C; Pirovani, Carlos P; Gesteira, Abelmon S

    2015-03-03

    Rootstocks play a major role in the tolerance of citrus plants to water deficit by controlling and adjusting the water supply to meet the transpiration demand of the shoots. Alterations in protein abundance in citrus roots are crucial for plant adaptation to water deficit. We performed two-dimensional electrophoresis (2-DE) separation followed by LC/MS/MS to assess the proteome responses of the roots of two citrus rootstocks, Rangpur lime (Citrus limonia Osbeck) and 'Sunki Maravilha' (Citrus sunki) mandarin, which show contrasting tolerances to water deficits at the physiological and molecular levels. Changes in the abundance of 36 and 38 proteins in Rangpur lime and 'Sunki Maravilha' mandarin, respectively, were observed via LC/MS/MS in response to water deficit. Multivariate principal component analysis (PCA) of the data revealed major changes in the protein profile of 'Sunki Maravilha' in response to water deficit. Additionally, proteomics and systems biology analyses allowed for the general elucidation of the major mechanisms associated with the differential responses to water deficit of both varieties. The defense mechanisms of Rangpur lime included changes in the metabolism of carbohydrates and amino acids as well as in the activation of reactive oxygen species (ROS) detoxification and in the levels of proteins involved in water stress defense. In contrast, the adaptation of 'Sunki Maravilha' to stress was aided by the activation of DNA repair and processing proteins. Our study reveals that the levels of a number of proteins involved in various cellular pathways are affected during water deficit in the roots of citrus plants. The results show that acclimatization to water deficit involves specific responses in Rangpur lime and 'Sunki Maravilha' mandarin. This study provides insights into the effects of drought on the abundance of proteins in the roots of two varieties of citrus rootstocks. In addition, this work allows for a better understanding of the

  13. Extraction of pectic enzymes from of Lulo (Solanum quitoense lam) involved in softening

    International Nuclear Information System (INIS)

    Rodriguez Nieto, Jeimmy Marcela; Restrepo Sanchez, Luz Patricia

    2011-01-01

    The main problem of post-harvest deterioration of Lulo (Solanum quitoense lam) is the softening is the main problem of post-harvest deterioration of Lulo that is generated mainly by the activity of pectic enzymes, which attack the structural network of the cell wall. this research was based on finding the best conditions structural cell wall network for extraction and measurement of enzyme activity pectinesterase (PE), polygalacturonase (PG) and pectato liasa (PL); tools needed to study the further role of these enzymes in the deterioration of pectatelyase fruit softening, due to various metabolic changes. It was found that the first two enzymes can be extracted simultaneously with 20 mm phosphate buffer pH 7.0, 0.06 m NaCl and 60 minutes of extraction, ratio 1:2 (plant material: extraction buffer), pectatelyase extracted with 20 mm phosphate buffer pH 7.0, 20 mm cysteine and 30 minutes of extraction, ratio 1:3. for quantification of pectinesterase activity is necessary to incubate 15 minutes at 42 Celsius degrade, 2500 μl of crude enzyme extract (EE) in 20 mm phosphate buffer pH 7.0, to 0.15 m NaCl and 1.6% citrus pectin as (CP) substrate with apparent km values of 3.78% CP and vmax 17.95 mol h+/min, mg prot. for the quantification of pectinesterase activity is necessary to incubate 15 minutes to 42 Celsius degrade 2500 μl of crude enzyme extract (EE) in 20 mm phosphate buffer pH 7.0, 0.15 m NaCl and 1.6% citrus pectin as substrate with apparent km values of 3.78% CP and 17.95 μ vmax mol h+/min Mg prot. for the quantification of polygalacturonase activity is necessary to incubate 15 minutes to 37 Celsius degrade 30 μl (EE) in 200 mm acetate buffer pH 4.5, 0.25 m NaCl and 1.0% of APG as substrate, with apparent km values 0.141% of APG and vmax 28.46 nkat/s mg prot. for the quantification of the pectatelyase activity is necessary to incubate 2 minutes to 17 Celsius degrade, 100 μl (EE) in buffer tris: HCl pH 8.5, 50 mm 4 mm CaCl2 and 0.1% PGA as substrate, with

  14. Influence of natural pozzolana and lime additives on the temporal variation of soil compaction and shear strength

    Science.gov (United States)

    Harichane, Khelifa; Ghrici, Mohamed; Missoum, Hanifi

    2011-06-01

    Soil stabilization has been practiced for quite some time by adding mixtures, such as cement, lime and fly ash. The additives of lime (L), natural pozzolana (NP) or a combination of both were investigated here on the impact on the temporal variation of geotechnical characteristics of two cohesive soils. Lime and natural pozzolana were added at the content of 0-8% and 0-20%, respectively. The soil specimens were cured for 1, 7, 28 and 90 days and then tested for shear strength. Our data show that a combination of lime with natural pozzolana causes the increase in the maximum dry density but the decrease in the optimum moisture content in the gray soil, and vice verse in the red soil. The shear stress of both cohesive soils stabilized with lime or with the combination of lime and natural pozzolana was found to increase with time. The cohesion and the internal friction angle in lime-added samples were demonstrated to increase with time. The combination of lime with natural pozzolana exhibits a significant effect on the enhancement of the cohesion and the internal friction angle at later stages. The lime-natural pozzolana combination appears to produce higher shear parameters than lime or natural pozzolana used alone.

  15. Shear strength and compressibility behaviour of lime-treated organic clay

    OpenAIRE

    Yunus, NZM; Wanatowski, D; Hassan, NA; Marto, A

    2016-01-01

    Apart from strength characteristics, a review of studies on the compressibility of lime-treated soils is equally important that influenced the stability of soil structures. Due to the fact that no study has been carried out, an investigation on the effects of humic acid on strength and compressibility behaviour of lime-stabilised organic clay is presented in this paper. Unconfined Compressive Strength (UCS) and oedometer tests were carried out at different curing periods of 7, 28 and 90 days....

  16. Industrial Wastes as Auxiliary Additives to Cement/Lime Stabilization of Soils

    OpenAIRE

    James, Jijo; Pandian, P. Kasinatha

    2016-01-01

    Chemical stabilization involves the use of chemical agents for initiating reactions within the soil for modification of its geotechnical properties. Cement and lime stabilization have been the most common stabilization methods adopted for soil treatment. Cement stabilization results in good compressive strengths and is preferred for cohesionless to moderately cohesive soil but loses effectiveness when the soil is highly plastic. Lime stabilization is the most preferred method for plastic clay...

  17. Evaluation of Cement, Lime, and Asphalt Amended Municipal Solid Waste Incinerator Residues

    Science.gov (United States)

    1989-09-01

    the lime column over time ( Atlas & Bartha , 1987). Certainly, a more extensive evaluation of the lime amended residue’s microbial activity is required...4.02 ASTM D 1559 (1988) Annual Book of ASTM Standards: Road & Paving Materials; Traveled Surface Characteristics, Sec 4, Vol 4.03 Atlas , R. & R. Bartha ...1987) Microbial Ecology : Fundamentals & Applications, Benjamin-Cummings, Menlo, CA Barrow N., J. Bowden, A. Posner, & J. Quirk (1981) Describing the

  18. Investigation of Hydraulic Binding Characteristics of Lime Based Mortars Used in Historical Masonry Structures

    Science.gov (United States)

    Binal, Adil

    2017-10-01

    In the historic masonry structures, hard and large rock fragments were used as the construction materials. The hydraulic binder material prepared to keep this used material in its entirety is a different material than the cement used today. Khorasan mortar made by using aggregate and lime exhibits a more flexible structure than the concrete. This feature allows the historic building to be more durable. There is also a significant industrial value because of the use of Khorasan mortar in the restoration of historic masonry structures. Therefore, the calculation of the ideal mixture of Khorasan mortar and the determination of its mechanical and physical properties are of great importance regarding preserving historic buildings. In this study, the mixtures of different lime and brick fractions were prepared. It was determined that Khorasan mortar shows the highest compressive strength in mixtures with water/lime ratio of 0.55 and lime/aggregate ratio of 0.66. By keeping the mixing ratio constant, it was observed that the strengths of the samples kept in the humidity chamber for different curing times increased day by day. The early strength values of samples with the high lime/aggregate ratio (l/a: 0.83) were higher than those with the low lime/aggregate ratio (l/a: 0.5). For the samples with low lime/aggregate ratio, there was an increase in the strength values depending on the curing period. As the cure duration increases, a chemical reaction takes place between the lime and the brick fracture, and as a result of this reaction, the strength values are increased.

  19. Consolidation of weak lime mortars by means of saturated solution of calcium hydroxide or barium hydroxide

    Czech Academy of Sciences Publication Activity Database

    Slížková, Zuzana; Drdácký, Miloš; Viani, Alberto

    2015-01-01

    Roč. 16, č. 4 (2015), s. 452-460 ISSN 1296-2074 R&D Projects: GA MK(CZ) DF11P01OVV012; GA MŠk(CZ) LO1219 Keywords : lime water * barium water * lime mortar * consolidation * peeling test * mechanical characteristic * physical characteristic * metakaolin Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 1.533, year: 2015 http://www.sciencedirect.com/science/article/pii/S1296207414001150

  20. Determination of optimal burning temperature ranges for production of natural hydraulic limes

    Czech Academy of Sciences Publication Activity Database

    Válek, Jan; van Halem, Eveline; Viani, Alberto; Pérez-Estébanez, Marta; Ševčík, Radek; Šašek, Petr

    2014-01-01

    Roč. 66, September (2014), s. 771-780 ISSN 0950-0618 R&D Projects: GA MK(CZ) DF11P01OVV010 Keywords : natural hydraulic lime * mechanical properties * calcination * CaO * X-ray diffraction * lime reactivity Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 2.296, year: 2014 http://www.sciencedirect.com/science/article/pii/S095006181400628X

  1. Biological effects in limed forests; Biologiska effekter i kalkad skog. Aarsrapport 1998. Effektuppfoeljning av Skogsstyrelsens program foer kalkning och vitaliseringsgoedsling av skogsmark

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Per-Erik; Akselsson, Cecilia; Bengtsson, Roland; Bjelke, Ulf

    1999-10-01

    The Swedish Board of Forestry experimental work with liming and vitalising (nutrient compensation) of forest soil includes an extensive review program of the effects of this work. Results from the experimental work are presented in annual reports. This report gives an account of the review program carried out to indicate the results of the biological effects. The studies are performed within the Swedish Board of Forestry's large-scale experiments with the liming and vitalising fertilisation of forest soil. The report covers the time period, or parts of the period, from 1991 to 1998. The results in short are as follows: (1) Benthic invertebrate: The investigation revealed that a dose of 3 tonnes per hectare was insufficient to have a substantial effect on the fauna in acidified streams during the first seven years after treatment. An increase in the number of species and taxon or larger bio-diversity could not be confirmed. No indications of harmful effects on the fauna, caused by high lime concentrations, were found., (2) Benthic algae: Changes to benthic flora in streams after soil treatment was minimal. The total number of species increased slightly after lime treatment. At the same time the number of acid indicating species diminished. In other words, the decrease in acidity has improved the water quality. No negative effects, as a result of soil treatment were found., (3) Nutritional status in needles: The trees reacted quickly to the treatments. The soil treatment led to an increase in levels of calcium in the needles. Treatment using wood ash and the vitalising agent 'Skogvital' led to an increase in calcium and boron levels. Treatment using a mixture of wood ash and lime resulted in increased magnesium and manganese levels. Samples were taken one and three years respectively after treatment. A longer period of time is required to carry out a detailed evaluation of the nutritional status of the needles., and (4) Tree vitality: It is not

  2. Volatile Profile of Croatian Lime Tree (Tilia sp., Fir Honeydew (Abies alba and Sage (Salvia officinalis Honey

    Directory of Open Access Journals (Sweden)

    Olivera Koprivnjak

    2007-01-01

    Full Text Available Volatile profiles of lime tree (Tilia sp., fir honeydew (Abies alba and sage (Salvia officinalis honey produced in Croatia have been studied by using headspace solid phase microextraction (HS-SPME followed by gas chromatography-mass spectrometry (GC-MS analysis. Melissopalynological and sensory characterization have been performed in order to check the reliability of botanical origin of the samples. In case of sage honey, sensory characteristics are reported for the first time and are rather uniform including: colour characterized as beige to jade, depending on the consistency; odour characterized as between light and medium intensity, slightly pungent and wooden; taste characterized as low sweetness, expressive acidity and apple caramel, with persistent fruity aftertaste. Characteristic volatile profiles of the analyzed honeys are described. Taking into consideration similarities with lime and fir honey volatile profiles reported in literature, characteristic volatile compounds resulting from qualitative data evaluation are proposed. Sage honey volatile profile has been reported for the first time and it was found quite different compared to the other studied honeys showing the lowest number of peaks among the studied honeys, 34. Several compounds belonging to the sage honey volatile profile have been identified for the first time in honeys. They include tetrahydro-2,2,5,5-tetramethylfuran, 3-hexenyl ester of butanoic acid, 2-methylbenzene, maltol, methyl ester of 3-furanocarboxylic acid and benzeneacetic acid. Based on the obtained results and with the lack of comparative literature data, they are proposed as characteristic volatiles for the volatile pattern of sage honey.

  3. Brick and lime kilns in Ecuador. An example of woodfuel use in third world, small-scale industry

    Energy Technology Data Exchange (ETDEWEB)

    Barriga, A.; Duque, J.; Moreira, E.; Zabala, G.; Solis, M.; Marcial, J.; Carlozama, J. [Escuela Superior Politechnica del Litoral (ESPOL), Guayaquil (Ecuador); Svenningsson, P.J. [Stockholm Environment Inst. (Sweden)

    1992-12-31

    At the present, early stage of this project, it has been verified that the energy requirements in lime making are of the order of 5 to 10 MJ/kg limestone in continuous shaft kilns. Furthermore, there are no lime making practices applied in Ecuador that point towards any easy way of substantially reducing energy usage. The theoretical analysis, including comparison with systems that either use low-volatile fuels or guarantee the complete combustion of volatiles, shows the great importance that should be attached to complete combustion of the fuel. A substantial improvement in efficiency can be expected if the volatiles can be utilized through the introduction of secondary air, recirculation of gases, or devolatilization of the wood before it enters the shaft. Such schemes do however need to be cost effective as well, meaning that the investment cost, especially for more advanced components, has to be low. There may be some solutions to this, including construction of very simple, brick-made, wood pre-gasification chambers that are integrated with the shaft kiln. This will hopefully be looked into further during the next phases of this project. (12 refs., 12 figs., 12 tabs.)

  4. Evaluating and quantifying the liming potential of phosphate rocks

    International Nuclear Information System (INIS)

    Sikora, F.J.

    2002-01-01

    The liming potential of phosphate rock was evaluated with theoretical calculations and quantified by laboratory titration and soil incubation. Three anions present in the carbonate apatite structure of phosphate rock that can consume protons and cause an increase in pH when dissolved from apatite are PO 4 3- , CO 3 2- , and F - . The pKa for HF is so low that F - has very little effect on increasing pH. The pKa for 2 protons on H 2 PO 4 - and H 2 CO 3 are sufficiently high enough to cause an increase in pH with PO 4 3- and CO 3 2- released into solution if the pH range is between 4 and 6. Because of the greater molar quantity of PO 4 3- compared toCO 3 2- , PO 4 3- exerts a greater affect on the liming potential of P rock. For a variety of phosphate rocks with a axes ranging from 9.322 to 9.374 A in the carbonate apatite structure, the theoretical % calcium carbonate equivalence (CCE) ranges from 59.5 to 62%. With the presence of gangue carbonate minerals from 2.5 to 10% on a weight basis in the phosphate rocks, the theoretical %CCE ranges from 59.5 to 63.1%. Use of AOAC method 955.01 for quantifying the %CCE of North Carolina phosphate rock (NCPR) and Idaho phosphate rock (IDPR) resulted in %CCE ranging from 39.9 to 53.7% which were less than the theoretical values. The lower values measured in the AOAC method was presumed to be due to formation of CaHPO 4 or CaHPO 4 ·2H 2 O precipitates which would result in less than 2 protons neutralized per mole of PO 4 3- released from carbonate apatite. The highly concentrated solution formed in the method was considered not indicative of a soil solution and thus determined %CCE values would be suspect. A soil incubation study was conducted to determine a more appropriate %CCE value in a soil environment using Copper Basin, Tennessee soil with a soil pH of 4.2. Agricultural limestone, NCPR, IDPR, and a granulated IDPR were added to 100 g of soil at rates of 0.1, 0.3, 1, 3, and 10 g/kg soil, incubated for 105 days at field

  5. Effects of hydrated lime on radionuclides stabilization of Hanford tank residual waste.

    Science.gov (United States)

    Wang, Guohui; Um, Wooyong; Cantrell, Kirk J; Snyder, Michelle M V; Bowden, Mark E; Triplett, Mark B; Buck, Edgar C

    2017-10-01

    Chemical stabilization of tank residual waste is part of a Hanford Site tank closure strategy to reduce overall risk levels to human health and the environment. In this study, a set of column leaching experiments using tank C-104 residual waste were conducted to evaluate the leachability of uranium (U) and technetium (Tc) where grout and hydrated lime were applied as chemical stabilizing agents. The experiments were designed to simulate future scenarios where meteoric water infiltrates through the vadose zones into the interior of the tank filled with layers of grout or hydrated lime, and then contacts the residual waste. Effluent concentrations of U and Tc were monitored and compared among three different packing columns (waste only, waste + grout, and waste + grout + hydrated lime). Geochemical modeling of the effluent compositions was conducted to determine saturation indices of uranium solid phases that could control the solubility of uranium. The results indicate that addition of hydrated lime strongly stabilized the uranium through transforming uranium to a highly insoluble calcium uranate (CaUO 4 ) or similar phase, whereas no significant stabilization effect of grout or hydrated lime was observed on Tc leachability. The result implies that hydrated lime could be a great candidate for stabilizing Hanford tank residual wastes where uranium is one of the main concerns. Published by Elsevier Ltd.

  6. Effect of Lime Stabilization on Vertical Deformation of Laterite Halmahera Soil

    Science.gov (United States)

    Saing, Zubair; Djainal, Herry

    2018-04-01

    In this paper, the study was conducted to determine the lime effect on vertical deformation of road base physical model of laterite Halmahera soil. The samples of laterite soil were obtained from Halmahera Island, North Maluku Province, Indonesia. Soil characteristics were obtained from laboratory testing, according to American Standard for Testing and Materials (ASTM), consists of physical, mechanical, minerals, and chemical. The base layer of physical model testing with the dimension; 2m of length, 2m of width, and 1.5m of height. The addition of lime with variations of 3, 5, 7, an 10%, based on maximum dry density of standard Proctor test results and cured for 28 days. The model of lime treated laterite Halmahera soil with 0,1m thickness placed on subgrade layer with 1,5m thickness. Furthermore, the physical model was given static vertical loading. Some dial gauge is placed on the lime treated soil surface with distance interval 20cm, to read the vertical deformation that occurs during loading. The experimentals data was analyzed and validated with numerical analysis using finite element method. The results showed that the vertical deformation reduced significantly on 10% lime content (three times less than untreated soil), and qualify for maximum deflection (standard requirement L/240) on 7-10% lime content.

  7. Characterization of historic lime mortars by neutron scattering and mercury porosimetry

    International Nuclear Information System (INIS)

    Zouridakis, N.; Stefanopoulos, K.L.; Treimer, W.

    1999-01-01

    Complete text of publication follows. Lime mortars were commonly used in building from ancient Greek times through to the beginning of the nineteenth century [1]. In the past few years, the increased interest in conservation and restoration of historic monuments requires a better knowledge of the structure and composition of lime mortars resulting from the various additives, as well as the preparation technique each time used. Lime mortars from ancient Greek monuments have been dated by using the radiocarbon method [2]. Furthermore, a wide selection of lime mortars from known historic periods and monuments in Greece has been examined by mercury porosimetry. It was found that their structure depends on the utilization of the monument which come from. In specific, lime mortars coming from residences have more or less the same structure, whereas the preparation technique differs for lime mortars coming from tombs and walls. The weathering effects on the porous system of the mortars are studied by neutron scattering. (author) [1] Brown, P.W., and Clifton, J.R., 'Air pollution and conservation', eds. J. Roswall and S. Aleby, 225 (1988), Elsevier, Amsterdam.; [2] N. Zouridakis, J.F. Sliege, A. Person et al., Archaeometry, 60 (1987) 29

  8. Liming effect in the degradation of 14C-glyphosate in soils

    International Nuclear Information System (INIS)

    Arantes, Sayonara A.C.M.; Lavorenti, Arquimedes

    2007-01-01

    Liming is soil fertility management practice essential in tropical soils, in general extremely acidic. This practice, by influencing physical, chemical and biological features of soils may influence the behavior of organic molecules in soils. The glyphosate is one the most widely used pesticides in Brazil in several cultures to pest management control. Studies on its fate in soil are still incipient, mainly under the effect of liming practice The objective of the present study was to verify the effect of liming practice in the degradation of glyphosate in Red Latosol (LE) and Quartzarenic Neosol (RQ) soils and also in the microbial activity of the same soils. The experiment was conducted in a completely randomized design in a 2 x 2 factorial scheme, corresponding to two soils and two management conditions (with liming and without liming), with four replicates. The Radiometric technique was utilized to evaluate the evolution the 14 CO 2 at intervals of 7 days, during 70 days. The study of microbial activity was conducted parallel to the degradation experiment, using the methodology of radiolabelled glucose ( 14 C-glucose), which was measured at intervals of fourteen days, during 70 days. The results showed that in the studied soils, the liming increased the 14 C-glyphosate mineralization and the microbial activity. (author)

  9. Liming effect in the degradation of 14C-glyphosate in soils

    Energy Technology Data Exchange (ETDEWEB)

    Arantes, Sayonara A.C.M.; Lavorenti, Arquimedes [Universidade de Sao Paulo (USP), Piracicaba, SP (Brazil). Escola Superior de Agricultura Luiz de Queiroz]. E-mails: samoreno@esalq.usp.br; alavoren@esalq.usp.br; Tornisielo, Valdemar L. [Centro de Energia Nuclear na Agricultura (CENA), Piracicaba, SP (Brazil)]. E-mail: vltornis@cena.usp.br

    2007-07-01

    Liming is soil fertility management practice essential in tropical soils, in general extremely acidic. This practice, by influencing physical, chemical and biological features of soils may influence the behavior of organic molecules in soils. The glyphosate is one the most widely used pesticides in Brazil in several cultures to pest management control. Studies on its fate in soil are still incipient, mainly under the effect of liming practice The objective of the present study was to verify the effect of liming practice in the degradation of glyphosate in Red Latosol (LE) and Quartzarenic Neosol (RQ) soils and also in the microbial activity of the same soils. The experiment was conducted in a completely randomized design in a 2 x 2 factorial scheme, corresponding to two soils and two management conditions (with liming and without liming), with four replicates. The Radiometric technique was utilized to evaluate the evolution the {sup 14}CO{sub 2} at intervals of 7 days, during 70 days. The study of microbial activity was conducted parallel to the degradation experiment, using the methodology of radiolabelled glucose ({sup 14}C-glucose), which was measured at intervals of fourteen days, during 70 days. The results showed that in the studied soils, the liming increased the {sup 14}C-glyphosate mineralization and the microbial activity. (author)

  10. The Effect of Kaffir Lime Leaves Distillation Residue Oleoresin Concentration on Active Paper Packaging Characteristics

    Science.gov (United States)

    Kawiji; Utami, R.; Ulum, S.; Khasanah, L. U.; Manuhara, G. J.; Atmaka, W.

    2018-03-01

    Oleoresin of kaffir lime leaves distillation residue still contains some active compounds such as Citronellal, β-Citronellol, and Linalool which potential to incorporated on the active paper packaging. The purposes of this study were to determine the effect of kaffir lime leaves distillation residue oleoresin concentration on the physical characteristics, sensory characteristics, and antimicrobial activity of the active paper packaging incorporated with kaffir lime leaves distillation residue oleoresin and to determine the functional groups of active paper packaging. The concentration of kaffir lime leaves distillation residue oleoresin were varied at 0%, 2%, 4% and 6%. The result showed that the addition of kaffir lime leaves distillation residue oleoresin increased the thickness and moisture content of the paper and decreased the tensile strengths and folding endurances of active paper packaging. The microbial inhibition tends to increase along with the higher oleoresin concentration addition. Aromatic CH group were found at a wavelength of 897.90 cm-1 of on paper packaging with 2% oleoresin indicated as functional aromatic functional group allegedly obtained from the kaffir lime leaves oleoresin.

  11. A Comparison between Lime and Alkaline Hydrogen Peroxide Pretreatments of Sugarcane Bagasse for Ethanol Production

    Science.gov (United States)

    Rabelo, Sarita C.; Filho, Rubens Maciel; Costa, Aline C.

    Pretreatment procedures of sugarcane bagasse with lime (calcium hydroxide) or alkaline hydrogen peroxide were evaluated and compared. Analyses were performed using 2 × 2 × 2 factorial designs, with pretreatment time, temperature, and lime loading and hydrogen peroxide concentration as factors. The responses evaluated were the yield of total reducing sugars (TRS) and glucose released from pretreated bagasse after enzymatic hydrolysis. Experiments were performed using the bagasse as it comes from an alcohol/ sugar factory and bagasse in the size range of 0.248 to 1.397 mm (12-60 mesh). The results show that when hexoses and pentoses are of interest, lime should be the pretreatment agent chosen, as high TRS yields are obtained for nonscreened bagasse using 0.40 g lime/g dry biomass at 70 °C for 36 h. When the product of interest is glucose, the best results were obtained with lime pretreatment of screened bagasse. However, the results for alkaline peroxide and lime pretreatments of nonscreened bagasse are not very different.

  12. Development of a three-dimensional CFD model for rotary lime kilns

    Energy Technology Data Exchange (ETDEWEB)

    Lixin Tao; Blom, Roger (FS Dynamics Sweden AB, Goeteborg (Sweden)); Nordgren, Daniel (Innventia, Stockholm (Sweden))

    2010-11-15

    In the calcium loop of the recovery cycle in a Kraft process of pulp and paper production, rotary lime kilns are used to convert the lime mud, mainly CaCO3, back to quick lime, CaO, for re-use in the causticizing process. The lime kilns are one of the major energy consumption devices for paper and pulp industry. Because of the rising oil price and new emission limits, the pulp mills have been forced to look for alternative fuels for their lime kilns. One interesting alternative to oil, often easily available at pulp mills, is biofuels such as sawdust and bark. However the practical kiln operation often encounters some difficulties because of the uncertainties around the biofuel impact on the lime kiln performance. A deeper understanding of the flame characteristics is required when shifting from oil to biofuels. Fortunately recent advances in modern Computational Fluid Dynamics, CFD, have provided the possibility to study and predict the detailed flame characteristics regarding the lime kiln performance. In this project a three-dimensional CFD model for rotary lime kilns has been developed. To simulate a rotary lime kiln the developed CFD model integrates the three essential sub-models, i.e. the freeboard hot flow model, the lime bed model and the rotating refractory wall model and it is developed based on the modern CFD package: FLUENT which is commercially available on the market. The numerical simulations using the developed CFD model have been performed for three selected kiln operations fired with three different fuel mixtures. The predicted results from the CFD modelling are presented and discussed in order to compare the impacts on the kiln performance due to the different firing conditions. During the development, the lime kiln at the Soedra Cell Moensteraas mill has been used as reference kiln. To validate the CFD model, in-plant measurements were carried out in the Moensteraas lime kiln during an experiment campaign. The results obtained from the

  13. Nonlinear dynamics of spring softening and hardening in folded-mems comb drive resonators

    KAUST Repository

    Elshurafa, Amro M.

    2011-08-01

    This paper studies analytically and numerically the spring softening and hardening phenomena that occur in electrostatically actuated microelectromechanical systems comb drive resonators utilizing folded suspension beams. An analytical expression for the electrostatic force generated between the combs of the rotor and the stator is derived and takes into account both the transverse and longitudinal capacitances present. After formulating the problem, the resulting stiff differential equations are solved analytically using the method of multiple scales, and a closed-form solution is obtained. Furthermore, the nonlinear boundary value problem that describes the dynamics of inextensional spring beams is solved using straightforward perturbation to obtain the linear and nonlinear spring constants of the beam. The analytical solution is verified numerically using a Matlab/Simulink environment, and the results from both analyses exhibit excellent agreement. Stability analysis based on phase plane trajectory is also presented and fully explains previously reported empirical results that lacked sufficient theoretical description. Finally, the proposed solutions are, once again, verified with previously published measurement results. The closed-form solutions provided are easy to apply and enable predicting the actual behavior of resonators and gyroscopes with similar structures. © 2011 IEEE.

  14. Effect of acoustic softening on the thermal-mechanical process of ultrasonic welding.

    Science.gov (United States)

    Chen, Kunkun; Zhang, Yansong; Wang, Hongze

    2017-03-01

    Application of ultrasonic energy can reduce the static stress necessary for plastic deformation of metallic materials to reduce forming load and energy, namely acoustic softening effect (ASE). Ultrasonic welding (USW) is a rapid joining process utilizing ultrasonic energy to form a solid state joint between two or more pieces of metals. Quantitative characterization of ASE and its influence on specimen deformation and heat generation is essential to clarify the thermal-mechanical process of ultrasonic welding. In the present work, experiments were set up to found out mechanical behavior of copper and aluminum under combined effect of compression force and ultrasonic energy. Constitutive model was proposed and numerical implemented in finite element model of ultrasonic welding. Thermal-mechanical analysis was put forward to explore the effect of ultrasonic energy on the welding process quantitatively. Conclusions can be drawn that ASE increases structural deformation significantly, which is beneficial for joint formation. Meanwhile, heat generation from both frictional work and plastic deformation is slightly influenced by ASE. Based on the proposed model, relationship between ultrasonic energy and thermal-mechanical behavior of structure during ultrasonic welding was constructed. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Shear Behavior Models of Steel Fiber Reinforced Concrete Beams Modifying Softened Truss Model Approaches.

    Science.gov (United States)

    Hwang, Jin-Ha; Lee, Deuck Hang; Ju, Hyunjin; Kim, Kang Su; Seo, Soo-Yeon; Kang, Joo-Won

    2013-10-23

    Recognizing that steel fibers can supplement the brittle tensile characteristics of concrete, many studies have been conducted on the shear performance of steel fiber reinforced concrete (SFRC) members. However, previous studies were mostly focused on the shear strength and proposed empirical shear strength equations based on their experimental results. Thus, this study attempts to estimate the strains and stresses in steel fibers by considering the detailed characteristics of steel fibers in SFRC members, from which more accurate estimation on the shear behavior and strength of SFRC members is possible, and the failure mode of steel fibers can be also identified. Four shear behavior models for SFRC members have been proposed, which have been modified from the softened truss models for reinforced concrete members, and they can estimate the contribution of steel fibers to the total shear strength of the SFRC member. The performances of all the models proposed in this study were also evaluated by a large number of test results. The contribution of steel fibers to the shear strength varied from 5% to 50% according to their amount, and the most optimized volume fraction of steel fibers was estimated as 1%-1.5%, in terms of shear performance.

  16. Shear Behavior Models of Steel Fiber Reinforced Concrete Beams Modifying Softened Truss Model Approaches

    Directory of Open Access Journals (Sweden)

    Joo-Won Kang

    2013-10-01

    Full Text Available Recognizing that steel fibers can supplement the brittle tensile characteristics of concrete, many studies have been conducted on the shear performance of steel fiber reinforced concrete (SFRC members. However, previous studies were mostly focused on the shear strength and proposed empirical shear strength equations based on their experimental results. Thus, this study attempts to estimate the strains and stresses in steel fibers by considering the detailed characteristics of steel fibers in SFRC members, from which more accurate estimation on the shear behavior and strength of SFRC members is possible, and the failure mode of steel fibers can be also identified. Four shear behavior models for SFRC members have been proposed, which have been modified from the softened truss models for reinforced concrete members, and they can estimate the contribution of steel fibers to the total shear strength of the SFRC member. The performances of all the models proposed in this study were also evaluated by a large number of test results. The contribution of steel fibers to the shear strength varied from 5% to 50% according to their amount, and the most optimized volume fraction of steel fibers was estimated as 1%–1.5%, in terms of shear performance.

  17. Noise-induced chaos and basin erosion in softening Duffing oscillator

    International Nuclear Information System (INIS)

    Gan Chunbiao

    2005-01-01

    It is common for many dynamical systems to have two or more attractors coexist and in such cases the basin boundary is fractal. The purpose of this paper is to study the noise-induced chaos and discuss the effect of noises on erosion of safe basin in the softening Duffing oscillator. The Melnikov approach is used to obtain the necessary condition for the rising of chaos, and the largest Lyapunov exponent is computed to identify the chaotic nature of the sample time series from the system. According to the Melnikov condition, the safe basins are simulated for both the deterministic and the stochastic cases of the system. It is shown that the external Gaussian white noise excitation is robust for inducing the chaos, while the external bounded noise is weak. Moreover, the erosion of the safe basin can be aggravated by both the Gaussian white and the bounded noise excitations, and fractal boundary can appear when the system is only excited by the random processes, which means noise-induced chaotic response is induced

  18. Softening mechanisms of the AISI 410 martensitic stainless steel under hot torsion simulation

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Thiago Santana de; Silva, Eden Santos; Rodrigues, Samuel Filgueiras; Nascimento, Carmem Celia Francisco; Leal, Valdemar Silva; Reis, Gedeon Silva, E-mail: samuel.filgueiras@ifma.edu.br [Instituto Federal do Maranhao (PPGEM/IFMA), Sao Luis, MA (Brazil)

    2017-03-15

    This study investigated the softening mechanisms of the AISI 410 martensitic stainless steel during torsion simulation under isothermal continuous in the temperature range of 900 to 1150 °C and strain rates of 0.1 to 5.0s{sup -1}. In the first part of the curves, before the peak, the results show that the critical (ε-c) and peak (ε-p) strains are elevated for higher strain rate and lower temperatures contributing for higher strain hardening rate (h). Moreover, this indicated that dynamic recrystallization (DRX) and dynamic recovery (DRV) are not effective in this region. After the peak, the reductions in stresses are associated to the different DRX/DRV competitions. For lower temperatures and higher strain rates there is a delay in the DRX while the DRV is acting predominantly (with low Avrami exponent (n) and high t{sub 0.5}). The steady state was reached after large strains showing DRX grains, formation of retained austenite and the presence of chromium carbide (Cr{sub 23}C{sub 6}) and ferrite δ at the martensitic grain boundaries. These contribute for impairing the toughness and ductility on the material. The constitutive equations at the peak strain indicated changes in the deformation mechanism, with variable strain rate sensitivity (m), which affected the final microstructure. (author)

  19. The anti-senescence effect of resveratrol reduces postharvest softening rate in cherimoya fruit

    Directory of Open Access Journals (Sweden)

    Aaran Aquilino Morales Pérez

    2014-03-01

    Full Text Available Due to its climateric behavior, the cherimoya fruit (Annona cherimola Mill. is a very perishable commodity. Present research aimed to observe the anti-senescence effect of resveratrol (RVS; this plant bioregulator was applied at 1.6, 0.16, 0.016 and 0 mM at 0, 8 and 15 days before harvest (DBH. At 1, 7 and 15 days of postharvest life, several physical and biochemical determinations were performed on the cherimoya fruit. After 15 days under room temperature conditions, in relation to control fruit, those fruit with 1.6 mM RVS applied 15 DBH reduced skin softening rate 78% and 54% for ‘Fino de Jete’ and ‘Bronceada’, respectively. Similarly, after 15 days of storage, a non-trained group of tasters preferred those fruit treated with 1.6 mM RVS 15 DBH; they qualified the fruit as better than the control fruit in presentation, aroma and taste.

  20. Lime and rates and sources of phosphorus as influencing soybean yield and chemical properties of Pelotas soil (alfisol)

    International Nuclear Information System (INIS)

    Machado, M.O.

    1983-01-01

    The effect of five phosphates as sources of phosphorus for soybean (Bragg cultivar) was evaluated in two rates (100 and 200 Kg/ha of total P 2 O 5 ), on limed and unlimed soil condtions. The experiment was carried out under field conditions, during the soybean growing season of 1973/74, 1974/75, 1975/76 and 1976/77, at UEPAE Pelotas station. The pH and the exchangeable Ca + Mg content from the soil were increased with Gafsa phosphate, but mainly with lime, Thomas slag and Yoorin thermophosphate application. The exchangeable Al content was eliminated by lime application and decreased annually by application of Gafsa phosphate, Thomas slag and Yoorin thermophosphate, when the lime was not applied. Thomas slag and Yoorin thermophosphate were the best phosphates for grain yield and do without lime: however, under limed soil conditions all phosphates had some efficiency, except for the Gafsa phosphate in the first growing season. (Author) [pt

  1. The growth of Scots pine and the availability of nutrients in old Finnish liming experiments on drained peatlands

    International Nuclear Information System (INIS)

    Nieminen, M.; Paetilae, A.

    1994-01-01

    Liming (with applications of 1000 to 8000 kg/ha) had no long- term (1929-1985) effect on the growth of Scots pine on drained oligotrophic peatlands. Liming plus NPK fertilization had a variable effect on the growth of stands. The same treatment could result in a very different response in different experimental areas. Both liming alone and liming plus NPK fertilization increased the calcium, magnesium and nitrogen contents of peat and decreased the C/Nratio and acidity. Liming plus fertilization decreased needle boron and manganese and increased calcium and nitrogen concentrations. The results of peat and needle analysis indicated that the changes in nitrogen availability to trees caused by liming have not been sufficient enough to affect tree growth. It was also concluded that boron deficiency was the main reason for the lowered yield. (26 refs., 6 tabs., 8 figs.) (author)

  2. Internal friction of hydrated soda-lime-silicate glasses.

    Science.gov (United States)

    Reinsch, S; Müller, R; Deubener, J; Behrens, H

    2013-11-07

    The internal friction of hydrated soda-lime-silica glasses with total water content (C(W)) up to 1.9 wt. % was studied by dynamic mechanical analysis (DMA) using temperature-frequency sweeps from 723 K to 273 K and from 1 s(-1) to 50 s(-1). Total water content and concentrations of H2O molecules (C(H2O)) and OH groups (C(OH)) in the DMA specimens were determined by infrared spectroscopy. For low water contents (C(W) ≈ C(OH) friction peaks below the glass transition (α relaxation) were assigned to the low-temperature motion of alkali ions (γ relaxation) and cooperative movements of dissimilar mobile species under participation of OH at higher temperature (β(OH) relaxation). For large water contents (C(W) > 1 wt. %), where significant amounts of molecular water are evident (C(H2O) > 0.15 wt. %), however, internal friction spectra change unexpectedly: the β(OH) peak heights saturate and a low temperature shoulder appears on the β-relaxation peak. This emerging relaxation mode (β(H2O) relaxation) was assigned to the motions of H2O molecules. β(H2O) relaxation was found to be faster than β(OH) but slower than γ relaxation. Activation energy of the different relaxation modes increased in the order γ < β(H2O) < β(OH) < α.

  3. Nutritional characteristics of two pigeon pea hybrids – Liming and phosphated fertilization

    Directory of Open Access Journals (Sweden)

    Marcia Atauri Cardelli de Lucena

    2012-12-01

    Full Text Available The use of legumes in animal production systems can be a sustainable alternative as a protein source in rotational grazing system and/or as a protein bank. Pigeon pea (Cajanus cajan (L. Millsp. figure as an example of success of this use on animal nutrition. The development of this species can be limited by the high acidity and low soil phosphorus content. There is a lack of scientific information on the effects of liming and phosphorus fertilization on some nutritional variables of two pigeon pea new hybrids. This study was conducted in pots containing 5 kg of soil in a greenhouse at the Instituto de Zootecnia, Nova Odessa, São Paulo State. There were studied two pigeon pea hybrids, H1 and H2, and the treatments involved agronomic practices: 1 No liming and without phosphorus (control, 2 Liming (L, 3 Phosphorus fertilization (P and 4 Liming plus phosphorus. Liming was proposed to increase soil base saturation to 50%, it was used dolomite lime PRNT = 90%, in an amount corresponding to 4.5 t/ha. Phosphorus fertilization (as superphosphate rate was 60 kg/ha of PO25. The experimental units were allocated according to a complete randomised block design, with five replications. We analyzed the levels of crude protein (CP, neutral detergent fiber (NDF, acid detergent fiber (ADF, in pigeon pea shoot at 45 days of age. Statistical analyzes were performed using the software SISVAR, averages were compared using test for multiple comparisons Student Newman-Keuls - SNK test (P < 0.05. The H1 hybrid had the highest content of CP, by applying P, lime plus P and the control treatment compared to H2 hybrid. The association lime plus P resulted in higher content of CP mainly due to the increased availability of P for plants. Smaller values were observed for NDF in H2 with P application. Lower values of ADF were observed in H1 in both control treatment and P application. The ADF values were lower for the hybrid H2 only for the treatment lime plus P. The two

  4. Lime-Based Sorbents for High-Temperature CO2 Capture—A Review of Sorbent Modification Methods

    Science.gov (United States)

    Manovic, Vasilije; Anthony, Edward J.

    2010-01-01

    This paper presents a review of the research on CO2 capture by lime-based looping cycles undertaken at CanmetENERGY’s (Ottawa, Canada) research laboratories. This is a new and very promising technology that may help in mitigation of global warming and climate change caused primarily by the use of fossil fuels. The intensity of the anticipated changes urgently requires solutions such as more cost-effective technologies for CO2 capture. This new technology is based on the use of lime-based sorbents in a dual fluidized bed combustion (FBC) reactor which contains a carbonator—a unit for CO2 capture, and a calciner—a unit for CaO regeneration. However, even though natural materials are cheap and abundant and very good candidates as solid CO2 carriers, their performance in a practical system still shows significant limitations. These limitations include rapid loss of activity during the capture cycles, which is a result of sintering, attrition, and consequent elutriation from FBC reactors. Therefore, research on sorbent performance is critical and this paper reviews some of the promising ways to overcome these shortcomings. It is shown that reactivation by steam/water, thermal pre-treatment, and doping simultaneously with sorbent reforming and pelletization are promising potential solutions to reduce the loss of activity of these sorbents over multiple cycles of use. PMID:20948952

  5. Trends of phytoplankton characteristics and their communities in pre- and post-liming time in Lake Orta (1984-1998

    Directory of Open Access Journals (Sweden)

    Pierisa PANZANI

    2001-02-01

    Full Text Available This paper is an assessment of the changing properties of Lake Orta phytoplankton in the period 1984-1998, which includes the large-scale liming carried out in the lake in 1989 and 1990. The phytoplankton is analysed first in its general properties (abundance, biovolume, chlorophyll-a concentration, average cell size, diversity by means of time courses of the mentioned variables based on monthly data through the entire period, and by correlations between the same variables. Moreover, through clustering techniques, the evolution of the species composition has been studied, showing the gradual decrease of chlorophytes after the liming and the noticeable increase of the diatom population, both as biovolume and diversity. Although the assemblage of the dominant species still mirrors the presence of some residual toxic compounds into the lake water, in the most recent period the evolution of the algal populations showed a clear trend towards a species assemblage more similar to those observed in the other deep italian subalpine lakes. After the improving of the chemical environment, the main abiotic factor that in the next years could play a major role in modifying the species assemblage is probably the phosphorus supply, whose in-lake concentration is low, despite the high annual load from the basin. A better understanding of the mechanisms underlying the phosphorus dynamics represent the basis to make reliable hypotheses about the future evolution of the phytoplankton assemblage.

  6. Synthesis of biocompatible and highly photoluminescent nitrogen doped carbon dots from lime: Analytical applications and optimization using response surface methodology

    Energy Technology Data Exchange (ETDEWEB)

    Barati, Ali [Faculty of Chemistry, Institute for Advanced Studies in Basic Sciences, Zanjan (Iran, Islamic Republic of); Shamsipur, Mojtaba, E-mail: mshamsipur@yahoo.com [Department of Chemistry, Razi University, Kermanshah (Iran, Islamic Republic of); Arkan, Elham [Nano Drug Delivery Research Center Kermanshah University of Medical Sciences, Kermanshah (Iran, Islamic Republic of); Hosseinzadeh, Leila [Novel Drug Delivery Research Center, Faculty of Pharmacy, Kermanshah University of Medical Sciences, Kermanshah (Iran, Islamic Republic of); Abdollahi, Hamid, E-mail: abd@iasbs.ac.ir [Faculty of Chemistry, Institute for Advanced Studies in Basic Sciences, Zanjan (Iran, Islamic Republic of)

    2015-02-01

    Herein, a facile hydrothermal treatment of lime juice to prepare biocompatible nitrogen-doped carbon quantum dots (N-CQDs) in the presence of ammonium bicarbonate as a nitrogen source has been presented. The resulting N-CQDs exhibited excitation and pH independent emission behavior; with the quantum yield (QY) up to 40%, which was several times greater than the corresponding value for CQDs with no added nitrogen source. The N-CQDs were applied as a fluorescent probe for the sensitive and selective detection of Hg{sup 2+} ions with a detection limit of 14 nM. Moreover, the cellular uptake and cytotoxicity of N-CQDs at different concentration ranges from 0.0 to 0.8 mg/ml were investigated by using PC12 cells as a model system. Response surface methodology was used for optimization and systematic investigation of the main variables that influence the QY, including reaction time, reaction temperature, and ammonium bicarbonate weight. - Highlights: • High fluorescent N-doped CQDs from lime juice have been prepared. • Response surface methodology was used to optimize and model the main factors. • N-doped CQDs were used in the selective and sensitive detection of Hg(II). • The biocompatibility of prepared N-doped CQDs was conformed using PC12 cells.

  7. Lime-Based Sorbents for High-Temperature CO2 Capture—A Review of Sorbent Modification Methods

    Directory of Open Access Journals (Sweden)

    Edward J. Anthony

    2010-08-01

    Full Text Available This paper presents a review of the research on CO2 capture by lime-based looping cycles undertaken at CanmetENERGY’s (Ottawa, Canada research laboratories. This is a new and very promising technology that may help in mitigation of global warming and climate change caused primarily by the use of fossil fuels. The intensity of the anticipated changes urgently requires solutions such as more cost-effective technologies for CO2 capture. This new technology is based on the use of lime-based sorbents in a dual fluidized bed combustion (FBC reactor which contains a carbonator—a unit for CO2 capture, and a calciner—a unit for CaO regeneration. However, even though natural materials are cheap and abundant and very good candidates as solid CO2 carriers, their performance in a practical system still shows significant limitations. These limitations include rapid loss of activity during the capture cycles, which is a result of sintering, attrition, and consequent elutriation from FBC reactors. Therefore, research on sorbent performance is critical and this paper reviews some of the promising ways to overcome these shortcomings. It is shown that reactivation by steam/water, thermal pre-treatment, and doping simultaneously with sorbent reforming and pelletization are promising potential solutions to reduce the loss of activity of these sorbents over multiple cycles of use.

  8. Cyclic softening based on dislocation annihilation at sub-cell boundary for SA333 Grade-6 C-Mn steel

    Science.gov (United States)

    Bhattacharjee, S.; Dhar, S.; Acharyya, S. K.; Gupta, S. K.

    2018-01-01

    In this work, the response of SA333 Grade-6 C-Mn steel subjected to uniaxial and in-phase biaxial tension-torsion cyclic loading is experimented and an attempt is made to model the material behaviour. Experimentally observed cyclic softening is modelled based on ‘dislocation annihilation at low angle grain boundary’, while Ohno-Wang kinematic hardening rule is used to simulate the stress-strain hysteresis loops. The relevant material parameters are extracted from the appropriate experimental results and metallurgical investigations. The material model is plugged as user material subroutine into ABAQUS FE platform to simulate pre-saturation low cycle fatigue loops with cyclic softening and other cyclic plastic behaviour under prescribed loading. The stress-strain hysteresis loops and peak stress with cycles were compared with the experimental results and good agreements between experimental and simulated results validated the material model.

  9. Altered cell wall disassembly during ripening of Cnr tomato fruit: implications for cell adhesion and fruit softening

    DEFF Research Database (Denmark)

    Orfila, C.; Huisman, M.M.H.; Willats, William George Tycho

    2002-01-01

    The Cnr (Colourless non-ripening) tomato (Lycopersicon esculentum Mill.) mutant has an aberrant fruit-ripening phenotype in which fruit do not soften and have reduced cell adhesion between pericarp cells. Cell walls from Cnr fruit were analysed in order to assess the possible contribution of pectic...... polysaccharides to the non-softening and altered cell adhesion phenotype. Cell wall material (CWM) and solubilised fractions of mature green and red ripe fruit were analysed by chemical, enzymatic and immunochemical techniques. No major differences in CWM sugar composition were detected although differences were...... that was chelator-soluble was 50% less in Cnr cell walls at both the mature green and red ripe stages. Chelator-soluble material from ripe-stage Cnr was more susceptible to endo-polygalacturonase degradation than the corresponding material from wild-type fruit. In addition, cell walls from Cnr fruit contained...

  10. Submicroscopic structure role in resistance of microplastic deformation of precipitation hardening nickel-chromium base alloys. 2. Softening stage

    International Nuclear Information System (INIS)

    Gitgarts, M.I.; Kukareko, V.A.

    1985-01-01

    Reasons for decrease of elastic limit and hardness of KhN77TYuR, KhN56VMTYu and KhN67VMTYu alloys at early stages of ageing are analyzed. Alloy softening is shown to be conditioned by development of spatial ordering of γ'-particles by the matrix volume. It is concluded that regularity in particle disposition reduces resistance to microplastic shear to a greater extent than to macroplastic strains

  11. Softenin, a novel protein that softens the connective tissue of sea cucumbers through inhibiting interaction between collagen fibrils.

    Directory of Open Access Journals (Sweden)

    Yasuhiro Takehana

    Full Text Available The dermis in the holothurian body wall is a typical catch connective tissue or mutable collagenous tissue that shows rapid changes in stiffness. Some chemical factors that change the stiffness of the tissue were found in previous studies, but the molecular mechanisms of the changes are not yet fully understood. Detection of factors that change the stiffness by working directly on the extracellular matrix was vital to clarify the mechanisms of the change. We isolated from the body wall of the sea cucumber Stichopus chloronotus a novel protein, softenin, that softened the body-wall dermis. The apparent molecular mass was 20 kDa. The N-terminal sequence of 17 amino acids had low homology to that of known proteins. We performed sequential chemical and physical dissections of the dermis and tested the effects of softenin on each dissection stage by dynamic mechanical tests. Softenin softened Triton-treated dermis whose cells had been disrupted by detergent. The Triton-treated dermis was subjected to repetitive freeze-and-thawing to make Triton-Freeze-Thaw (TFT dermis that was softer than the Triton-treated dermis, implying that some force-bearing structure had been disrupted by this treatment. TFT dermis was stiffened by tensilin, a stiffening protein of sea cucumbers. Softenin softened the tensilin-stiffened TFT dermis while it had no effect on the TFT dermis without tensilin treatment. We isolated collagen from the dermis. When tensilin was applied to the suspending solution of collagen fibrils, they made a large compact aggregate that was dissolved by the application of softenin or by repetitive freeze-and-thawing. These results strongly suggested that softenin decreased dermal stiffness through inhibiting cross-bridge formation between collagen fibrils; the formation was augmented by tensilin and the bridges were broken by the freeze-thaw treatment. Softenin is thus the first softener of catch connective tissue shown to work on the cross

  12. A randomised controlled trial of ion-exchange water softeners for the treatment of eczema in children.

    Directory of Open Access Journals (Sweden)

    Kim S Thomas

    2011-02-01

    Full Text Available Epidemiological studies and anecdotal reports suggest a possible link between household use of hard water and atopic eczema. We sought to test whether installation of an ion-exchange water softener in the home can improve eczema in children.This was an observer-blind randomised trial involving 336 children (aged 6 months to 16 years with moderate/severe atopic eczema. All lived in hard water areas (≥200 mg/l calcium carbonate. Participants were randomised to either installation of an ion-exchange water softener plus usual eczema care, or usual eczema care alone. The primary outcome was change in eczema severity (Six Area Six Sign Atopic Dermatitis Score, SASSAD at 12 weeks, measured by research nurses who were blinded to treatment allocation. Analysis was based on the intent-to-treat population. Eczema severity improved for both groups during the trial. The mean change in SASSAD at 12 weeks was -5.0 (20% improvement for the water softener group and -5.7 (22% improvement for the usual care group (mean difference 0.66, 95% confidence interval -1.37 to 2.69, p = 0.53. No between-group differences were noted in the use of topical corticosteroids or calcineurin inhibitors.Water softeners provided no additional benefit to usual care in this study population. Small but statistically significant differences were found in some secondary outcomes as reported by parents, but it is likely that such improvements were the result of response bias, since participants were aware of their treatment allocation. A detailed report for this trial is also available at http://www.hta.ac.uk.Current Controlled Trials ISRCTN71423189 Please see later in the article for the Editors' Summary.

  13. Liming the acid lake Hovvatn, Norway: a whole-ecosystem study

    Energy Technology Data Exchange (ETDEWEB)

    Raddum, G G; Brettum, P; Matzow, D; Nilssen, J P; Skov, A; Sveaelv, T; Wright, R F

    1986-12-01

    Hovvatn, a 1 sq. km. chronically-acidified lake in southernmost Norway, was treated with 200 tonne of powdered limestone in March 1981. An additional 40 tonne were added to a 0.046 sq km pond (Pollen) draining into Hovvatn. The lakes were stocked with brown trout in June 1981 and in each subsequent year. At ice-out pH rose from 4.4 to 6.3 (Hovvatn) and 7.5 (Pollen), Ca and alkalinity increased, and total Al decreased by 120 ..mu..g/l. None of the other major ions exhibited significant changes in concentration. Total organic C and P increased after liming. The phytoplankton community was dominated by chrysophytes and did not change significantly following liming. The zooplankton community was typical of acid lakes prior to liming. There was a clear succession in species dominance following treatment, although no new species immigrated to the lakes. Zoobenthos changed from a community characterized by low abundance and reduced number of species to increased abundance of oligochaetes, mayflies and chironomids. Hovvatn and Pollen were barren of fish prior to stocking. The stocked fish showed remarkably high growth rate during the first years. Liming apparently improved conditions for zoobenthos, enhancing the processing of fine detritus which in turn resulted in elevated levels of TOC and P in the lakewaters during the first year after liming. The oligotrophication process typical of acid lakes was temporarily reversed by liming. The interactions between groups of organisms in Hovvatn and Pollen indicates that many years are required before a new steady-state can be attained following liming. 61 references.

  14. Effectiveness of lime and peat applications on cadmium availability in a paddy soil under various moisture regimes.

    Science.gov (United States)

    Chen, Yanhui; Xie, Tuanhui; Liang, Qiaofeng; Liu, Mengjiao; Zhao, Mingliu; Wang, Mingkuang; Wang, Guo

    2016-04-01

    In paddy soils, amendments and moisture play important role in the immobilization of cadmium (Cd). The effects of applying lime, peat, and a combination of both on soil Eh, pH, and Cd availability in contaminated soils were investigated under wetted (80 ± 5 % of water holding capacity) and flooded (completely submerged) conditions. In wetted soils, there was little change in Eh, compared to flooded soils where Eh reduced rapidly. Amendments of lime only or in a mixture with peat increased soil pH to different degrees, depending on the lime application rate. However, peat addition only slightly affected soil pH. The decreased Cd availability in flooded soils was related to submergence duration and was significantly lower than that in wetted soils after 14 days. Liming wetted and flooded soils decreased exchangeable Cd and increased carbonates or Fe-Mn oxides bound fractions, while peat addition transformed Cd from carbonates to organic matter bound fractions. The combined application of peat and lime generally showed better inhibitory effects on the availability of Cd than separately application of lime or peat. Higher application rates of lime, peat, or their mixture were more effective at reducing Cd contamination in flooded soil. This indicates that application of peat and lime mixture under flooded conditions was most effective for in situ remediation of Cd-contaminated soils. Further studies are required to assess the long-term effectiveness of the peat and lime mixture on Cd availability in paddy soils.

  15. Dissolved organic carbon and nitrogen mineralization strongly affect co2 emissions following lime application to acidic soil

    International Nuclear Information System (INIS)

    Shaaban, M.; Peng, Q.; Lin, S.; Wu, Y.

    2014-01-01

    Emission of greenhouse gases from agricultural soils has main contribution to the climatic change and global warming. Dynamics of dissolved organic carbon (DOC) and nitrogen mineralization can affect CO/sub 2/ emission from soils. Influence of DOC and nitrogen mineralization on CO/sub 2/ emissions following lime application to acidic soil was investigated in current study. Laboratory experiment was conducted under aerobic conditions with 25% moisture contents (66% water-filled pore space) at 25 degree C in the dark conditions. Different treatments of lime were applied to acidic soil as follows: CK (control), L (low rate of lime: 0.2g lime / 100 g soil) and H (high rate of lime: 0.5g lime /100g soil). CO/sub 2/ emissions were measured by gas chromatography and dissolved organic carbon, NH4 +-N, NO/sub 3/ --N and soil pH were measured during incubation study. Addition of lime to acidic soil significantly increased the concentration of DOC and N mineralization rate. Higher concentrations of DOC and N mineralization, consequently, increased the CO/sub 2/ emissions from lime treated soils. Cumulative CO/sub 2/ emission was 75% and 71% higher from L and H treatments as compared to CK. The results of current study suggest that DOC and N mineralization are critical in controlling gaseous emissions of CO/sub 2/ from acidic soils following lime application. (author)

  16. The Padanian LiMeS. Spatial Interpretation of Local GHG Emission Data

    Directory of Open Access Journals (Sweden)

    Michèle Pezzagno

    2015-04-01

    Full Text Available The relevant role of spatial planning in the enforcement of climate change mitigation, managing the development of new low-carbon infrastructures and increasing system-wide efficiencies across sectors, has been addressed at global level (IPCC, 2014 WGIII. In this context, local GHG inventories appear a relevant tool toward the definition of a coherent, inter-sectorial background for local planning, mitigation, and adaptation policies.Taking advantage of consistent GHG emissions data availability in the Lombard context, local maps of direct GHG emissions have been linked with geographic data, including municipal boundaries, population data, and land-use information, produced and organized within the research PRIN 2007 From metropolitan city to metropolitan corridor: the case of the Po Valley Corridor.The results of this mapping exercise have been evaluated on the background of consolidated knowledge about northern Italy urban patterns, including the Linear Metropolitan System – LiMeS – and preliminary observations about characteristics, potential, and limits of the tool are proposed.

  17. Effect of attractive interactions on the water-like anomalies of a core-softened model potential.

    Science.gov (United States)

    Pant, Shashank; Gera, Tarun; Choudhury, Niharendu

    2013-12-28

    It is now well established that water-like anomalies can be reproduced by a spherically symmetric potential with two length scales, popularly known as core-softened potential. In the present study we aim to investigate the effect of attractive interactions among the particles in a model fluid interacting with core-softened potential on the existence and location of various water-like anomalies in the temperature-pressure plane. We employ extensive molecular dynamic simulations to study anomalous nature of various order parameters and properties under isothermal compression. Order map analyses have also been done for all the potentials. We observe that all the systems with varying depth of attractive wells show structural, dynamic, and thermodynamic anomalies. As many of the previous studies involving model water and a class of core softened potentials have concluded that the structural anomaly region encloses the diffusion anomaly region, which in turn, encloses the density anomaly region, the same pattern has also been observed in the present study for the systems with less depth of attractive well. For the systems with deeper attractive well, we observe that the diffusion anomaly region shifts toward higher densities and is not always enclosed by the structural anomaly region. Also, density anomaly region is not completely enclosed by diffusion anomaly region in this case.

  18. Changes in alpha-L-arabinofuranosidase activity in peel and pulp of banana (Musa sp.) fruits during ripening and softening.

    Science.gov (United States)

    Zhuang, Jun-Ping; Su, Jing; Li, Xue-Ping; Chen, Wei-Xin

    2007-04-01

    Arabinose is one of the most dynamic cell wall glycosyl residues released during fruit ripening, alpha-L-arabinofuranosidase (alpha-Arab) are major glycosidases that may remove arabinose units from fruit cell wall polysaccharides. To find out whether alpha-Arab plays important roles in banana fruit softening, the enzyme activities in peel and pulp, fruit firmness, respiration rate and ethylene release rate were assayed during banana softening. The results showed that alpha-Arab activities in banana pulp and peel increased slightly at the beginning of storage and reached their maxima when the fruit firmness decreased drastically, alpha-Arab activity increased by more than ten folds in both pulp and peel during ripening and alpha-Arab activities were higher in pulp than in peel. Treatment of banana fruits with ethylene absorbent postponed the time of reaching of its maxima of respiration and ethylene, enhanced the firmness of pup and decreased alpha-Arab activity in the peel and pulp. These results suggest that alpha-Arab induced the decrease of fruit firmness and played an important role in banana fruit softening, and its activity was regulated by ethylene.

  19. On the Rule of Mixtures for Predicting Stress-Softening and Residual Strain Effects in Biological Tissues and Biocompatible Materials

    Directory of Open Access Journals (Sweden)

    Alex Elías-Zúñiga

    2014-01-01

    Full Text Available In this work, we use the rule of mixtures to develop an equivalent material model in which the total strain energy density is split into the isotropic part related to the matrix component and the anisotropic energy contribution related to the fiber effects. For the isotropic energy part, we select the amended non-Gaussian strain energy density model, while the energy fiber effects are added by considering the equivalent anisotropic volumetric fraction contribution, as well as the isotropized representation form of the eight-chain energy model that accounts for the material anisotropic effects. Furthermore, our proposed material model uses a phenomenological non-monotonous softening function that predicts stress softening effects and has an energy term, derived from the pseudo-elasticity theory, that accounts for residual strain deformations. The model’s theoretical predictions are compared with experimental data collected from human vaginal tissues, mice skin, poly(glycolide-co-caprolactone (PGC25 3-0 and polypropylene suture materials and tracheal and brain human tissues. In all cases examined here, our equivalent material model closely follows stress-softening and residual strain effects exhibited by experimental data.

  20. On the Rule of Mixtures for Predicting Stress-Softening and Residual Strain Effects in Biological Tissues and Biocompatible Materials

    Science.gov (United States)

    Elías-Zúñiga, Alex; Baylón, Karen; Ferrer, Inés; Serenó, Lídia; Garcia-Romeu, Maria Luisa; Bagudanch, Isabel; Grabalosa, Jordi; Pérez-Recio, Tania; Martínez-Romero, Oscar; Ortega-Lara, Wendy; Elizalde, Luis Ernesto

    2014-01-01

    In this work, we use the rule of mixtures to develop an equivalent material model in which the total strain energy density is split into the isotropic part related to the matrix component and the anisotropic energy contribution related to the fiber effects. For the isotropic energy part, we select the amended non-Gaussian strain energy density model, while the energy fiber effects are added by considering the equivalent anisotropic volumetric fraction contribution, as well as the isotropized representation form of the eight-chain energy model that accounts for the material anisotropic effects. Furthermore, our proposed material model uses a phenomenological non-monotonous softening function that predicts stress softening effects and has an energy term, derived from the pseudo-elasticity theory, that accounts for residual strain deformations. The model’s theoretical predictions are compared with experimental data collected from human vaginal tissues, mice skin, poly(glycolide-co-caprolactone) (PGC25 3-0) and polypropylene suture materials and tracheal and brain human tissues. In all cases examined here, our equivalent material model closely follows stress-softening and residual strain effects exhibited by experimental data. PMID:28788466

  1. Circular economy in drinking water treatment: reuse of ground pellets as seeding material in the pellet softening process.

    Science.gov (United States)

    Schetters, M J A; van der Hoek, J P; Kramer, O J I; Kors, L J; Palmen, L J; Hofs, B; Koppers, H

    2015-01-01

    Calcium carbonate pellets are produced as a by-product in the pellet softening process. In the Netherlands, these pellets are applied as a raw material in several industrial and agricultural processes. The sand grain inside the pellet hinders the application in some high-potential market segments such as paper and glass. Substitution of the sand grain with a calcite grain (100% calcium carbonate) is in principle possible, and could significantly improve the pellet quality. In this study, the grinding and sieving of pellets, and the subsequent reuse as seeding material in pellet softening were tested with two pilot reactors in parallel. In one reactor, garnet sand was used as seeding material, in the other ground calcite. Garnet sand and ground calcite performed equally well. An economic comparison and a life-cycle assessment were made as well. The results show that the reuse of ground calcite as seeding material in pellet softening is technologically possible, reduces the operational costs by €38,000 (1%) and reduces the environmental impact by 5%. Therefore, at the drinking water facility, Weesperkarspel of Waternet, the transition from garnet sand to ground calcite will be made at full scale, based on this pilot plant research.

  2. Biocompatible water softening system using cationic protein from moringa oleifera extract

    Science.gov (United States)

    Nisha, R. R.; Jegathambal, P.; Parameswari, K.; Kirupa, K.

    2017-10-01

    In developing countries like India, the deciding factors for the selection of the specific water purification system are the flow rate, cost of implementation and maintenance, availability of materials for fabrication or assembling, technical manpower, energy requirement and reliability. But most of them are energy and cost intensive which necessitate the development of cost-effective water purification system. In this study, the feasibility of development of an efficient and cost-effective water purifier using Moringa oleifera cationic protein coated sand column to treat drinking water is presented. Moringa oleifera seeds contain cationic antimicrobial protein which acts as biocoagulant in the removal of turbidity and also aids in water softening. The main disadvantage of using Moringa seeds in water purification is that the dissolved organic matter (DOM) which is left over in the water contributes to growth of any pathogens that come into contact with the stored water. To overcome this limitation, the Moringa oleifera cationic protein coated sand (MOCP c-sand) is prepared in which the flocculant and antimicrobial properties of the MOCP are maintained and the DOM to be rinsed away. The efficiency of MOCP c-sand in removing suspended particles and reducing total hardness (TH), chloride, total dissolved solids (TDS), electrical conductivity (EC) was also studied. Also, it is shown that the functionalized sand showed the same treatment efficiency even after being stored dry and in dehydrated condition for 3 months. This confirms MOCP c-sand's potential as a locally sustainable water treatment option for developing countries since other chemicals used in water purification are expensive.

  3. The influence of lime and nitrogen fertilisers on spore counts of Pithomyces chartarum in pasture.

    Science.gov (United States)

    Cuttance, E L; Laven, R A; Mason, W A; Stevenson, M

    2016-11-01

    To determine whether the application of lime or nitrogen to pasture affected the spore counts of Pithomyces chartarum. The lime application studies were undertaken on a spring-calving, pasture-based, commercial dairy farm near Te Awamutu, New Zealand. On 6 November 2012, five randomly selected paddocks were split into three equal sections. In two of the sections, lime was applied at either 1.5 or 2.5 t/ha, and the central section was left as an untreated control. Each section was sampled for spore counting weekly from 16 January to 15 May 2013. Starting in January 2013, five other randomly selected paddocks were monitored for spore counts. On 20 March 2013 the average spore counts in three paddocks were >100,000 spores/g of pasture. These paddocks were then divided into three equal sections and lime was applied as described above. Spore counting in each section continued weekly until 15 May 2013. The nitrogen application study was carried out on three commercial dairy farms near Te Awamutu, New Zealand. Two randomly selected paddocks on each farm were divided into three equal sections and, on 20 December 2012, nitrogen in the form of urea was applied at either 50 or 80 kg urea/ha to two of the sections; the central section remained as an untreated control. Each section was sampled for spore counting weekly from 16 January to 15 May 2013. Following pre-summer lime application, treatment at 1.5 or 2.5 t/ha did not affect spore counts over time compared with the control section (p>0.26). Similarly following autumn lime application, treatment at 1.5 or 2.5 t/ha did not affect spore counts over time compared with the control section (p>0.11). Following nitrogen application median spore counts remained 0.49). This study found that application of lime before the risk period for facial eczema, in November, application of lime after a spore count rise, in March, or urea application in December did not affect changes in number of spores produced by P. chartarum. This

  4. Radiation dose estimation from the radioactivity analysis of lime and cement used in Bangladesh

    International Nuclear Information System (INIS)

    Alam, M.N.; Miah, M.M.H.; Chowdhury, M.I.; Kamal, M.; Ghose, S.; Islam, M.N.; Mustafa, M.N.; Miah, M.S.R.

    1999-01-01

    The radioactivity concentrations of 232 Th, 226 Ra, 40 K and 137 Cs were measured using high-resolution γ-ray spectrometry in limestone, powdered lime, by-product lime and cement used in Bangladesh. The activity concentrations, Ra equivalent activities, representative level index values for all samples and the effective dose equivalents due to the intake of the above-mentioned radionuclides in limestone and powdered lime by the adult group were estimated. The mean activity concentrations of 232 Th, 226 Ra and 40 K were 60.8, 60.2 and 928 Bq kg -1 , respectively for limestone, 107, 68.0 and 1660 Bq kg -1 , respectively, for powdered lime and 83.0, 31.0 and 972 Bq kg -1 , respectively, for by-product lime. For cement, the mean activity concentrations of 232 Th, 226 Ra and 40 K were observed to be 54.3, 29.7 and 523 Bq kg -1 , respectively. The presence of 137 Cs was not detectable in any of the studied samples. The measured average activities of 232 Th, 226 Ra and 40 K for all samples were relatively higher than the world typical values except for 226 Ra in cement and by-product lime. The calculated mean Ra equivalent values for limestone, powdered lime, by-product lime and cement were 219, 349, 224 and 148 Bq kg -1 , respectively. The corresponding representative level index values were found to be 1.63, 2.63, 1.68 and 1.09, respectively. The mean effective dose equivalent values of 232 Th, 226 Ra and 40 K for limestone were 56.5x10 -7 , 41.6x10 -8 and 50.8x10 -10 Sv g -1 , respectively, and those for powdered lime were 99.5x10 -7 , 46.9x10 -8 and 91.3x10 -10 Sv g -1 , respectively. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

  5. Expansion reduction of clayey soils through Surcharge application and Lime Treatment

    Directory of Open Access Journals (Sweden)

    T. López-Lara

    2017-12-01

    Full Text Available Expansive clayey soils produce heaving and cracking of floor slabs and walls. Expansive soils owe their characteristics to the presence of swelling clay minerals. This soil expands and contracts due to changes in the moisture content of the soil. In this study the surcharge required to counteract soil expansion was measured in natural expansive soils (untreated soils and lime treated soils starting at 19.61 kPa (2 Ton/m2 and continuing with increments of 19.61 kPa. Additionaly in lime treated soils the amount of lime was determined under different surcharges in order to reduce the expansion. The test results indicated that the surcharges applied to untreated soils were not proportional to the decrease of expansion which is probably due to the increase of soil density. In fact, only the initial surcharge of 19.61 kPa significantly decreased the expansion. According to the results, the soil expansion was considerably reduced (1.54% with the surcharge of 78.45 kPa, therefore this surcharge can be considered as the Swelling pressure. On the other hand the soil tested (high compressibility clay was stabilized with 6% of lime (without surcharges which was determined with the lowest value of liquid limit and plastic index as well as expansion test. After the application of surcharges and lime treatment to expansive soil, the surcharges of 39.22 kPa and 58.84 kPa decreased expansion and increased their resistance. This was concluded by similar low values of expansion (without settlements under both surcharges of each treated soil tested (2, 4 and 6% of lime. It can be concluded that the surcharge contributed to the decrease of soil expansion due to the decrease of the amount of lime required (6% without surcharge. So, 4% of lime was enough for the surcharge of 19.61 kPa and 2% of lime required the surcharge minimum of 39.22 kPa. This shows that the surcharge of a house on expansive soil reduces soil expansion and therefore reduces costs of any

  6. Roles of iron species and pH optimization on sewage sludge conditioning with Fenton's reagent and lime.

    Science.gov (United States)

    Yu, Wenbo; Yang, Jiakuan; Shi, Yafei; Song, Jian; Shi, Yao; Xiao, Jun; Li, Chao; Xu, Xinyu; He, Shu; Liang, Sha; Wu, Xu; Hu, Jingping

    2016-05-15

    Conditioning sewage sludge with Fenton's reagent could effectively improve its dewaterability. However, drawbacks of conditioning with Fenton's reagent are requirement of acidic conditions to prevent iron precipitation and subsequent neutralization with alkaline additive to obtain the pH of the filtrate close to neutrality. In this study, roles of pH were thoroughly investigated in the acidification pretreatment, Fenton reaction, and the final filtrate after conditioning. Through the response surface methodology (RSM), the optimal dosages of H2SO4, Fe(2+), H2O2, and lime acted as a neutralizer were found to be 0 (no acidification), 47.9, 34.3 and 43.2 mg/g DS (dry solids). With those optimal doses, water content of the dewatered sludge cakes could be reduced to 55.8 ± 0.6 wt%, and pH of the final filtrate was 6.6 ± 0.2. Fenton conditioning without initial acidification can simplify the conditioning process and reduce the usage of lime. The Fe(3+) content in the sludge cakes showed a close correlation with the dewaterability of conditioned sludge, i.e., the water content of sludge cakes, SRF (specific resistance to filtration), CST (capillary suction time), bound water content, and specific surface area. It indicated that the coagulation by Fe(3+) species in Fenton reaction could play an important role, compared to traditional Fenton oxidation effect on sludge conditioning. Thus, a two-step mechanism of Fenton oxidation and Fe(III) coagulation was proposed in sewage sludge conditioning. The mechanisms include the following: (1) extracellular polymeric substances (EPS) were firstly degraded into dissolved organics by Fenton oxidation; (2) bound water was converted to free water due to degradation of EPS; (3) the sludge particles were disintegrated into small ones by oxidation; (4) Fe(3+) generated from Fenton reaction acted as a coagulant to agglomerate smaller sludge particles into larger dense particles with less bond water; (5) finally, the dewatered

  7. Carbonation kinetics in roman-like lime mortar

    Directory of Open Access Journals (Sweden)

    Sánchez-Moral, S.

    2004-09-01

    Full Text Available The kinetic parameterisation of lime mortar carbonation is a useful technique for understanding ancient building methods and the long-lived physical-chemical stability of roman monuments. Portlandite (Ca(OH2 binders harden in the air on contact with atmospheric CO2, producing CaCO3. Water evaporation and the presence of silicate aggregates have a three-fold effect: prompting the development of a pore system that permits CO2, self-diffusion, reducing shrinkage and cracking during drying and (possibly giving rise to subsequent pozzolanic reactions. The present survey involved air-hardening a series of roman-like lime mortars which differed in terms of: (i type of aggregate, volcanic tephra and arkose; (ii aggregate/binder ratio, 1:2 as used in the catacombs and 1:4 as found in standard roman construction and (iii temperature, the 17 ºC prevailing in underground environments and the 30 ºC typical of warm Mediterranean areas. The analyses that provided the most useful information were performed in a classic X-ray diffractometer adapted to accommodate an author-designed chamber in which temperature control was achieved by an internal refrigerant and a PID-governed electrical heater Additional data were obtained with DTA and environmental scanning electron microscopy (ESEM. The tests conducted on the Roman-like lime mortars manufactured for the experiment showed that the hardening temperature is a critical factor in the initial phases of carbonation. Calcite precipitation rates and total mineral precipitation increased with temperature, but fell very quickly as calcite precipitated. In theoretical calculations assuming an open reactor with continuous CO2, input, total calcitisation time was found to be 156 m in. at 30 ºC and 175 min. at 17 ºC, whilst in the mortars actually hardened in the experimental part of the study, calcitisation gradually blocked the flow or CO2, gas into the

  8. Liming and fertilisation in Pinus taeda plantations with severe nutrient deficiency in savanna soils

    Directory of Open Access Journals (Sweden)

    Araína Hulmann Batista

    2014-11-01

    Full Text Available Soils with high acidity and low exchangeable bases may be responsible for low yields of Pinus taeda in a forest plantation at Jaguariaíva, Paraná State, Brazil. The aim of this study was to evaluate the effect of liming and fertilisation, applied over litter, on two selected areas with Pinus taeda plantations. Soil, litter and pine needles were evaluated for K, Ca and Mg concentrations and soil acidity parameters. Seven treatments were applied: (i complete (N, P, K, Zn, Cu, B, Mo, and lime; (ii without N, P, and K; (iii without Zn, Cu, B, and Mo; (iv without K; (v without Zn; (vi without lime; and (vii control (without nutrients and lime. Soil samples were collected at five soil depths (0-5, 5-10, 10-20, 20-40 and 40-60 cm simultaneously with litter samples. Needles were also collected from the first and second pine flushes. Liming induced soil pH, Ca2+, and Mg2+ increases, and the opposite was observed for Al3+ and Al saturation. Fertilisation increased soil exchangeable K+ concentrations and needle and litter K concentrations. The low Ca and Mg concentrations found in the plant needles might be attributable to their low mobility.

  9. Amendment of biosolids with waste materials and lime: Effect on geoenvironmental properties and leachate production.

    Science.gov (United States)

    Kayser, Claudia; Larkin, Tam; Singhal, Naresh

    2015-12-01

    Residuals from wastewater treatment operations (biosolids) were mixed with lime, fly ash, lime kiln dust, or two smelter slags to assess their efficacy as potential stabilisation agents by assessing their effects on the shear strength, compressibility, and solids content of mixtures. In addition, the minerals formed and leachate produced during stabilisation were determined. Tests were performed to explore the change of the geoenvironmental properties of the amended biosolids, while under pressure, at different scales using laboratory, pilot and field scale tests. The settlement characteristics of the amended biosolids under a range of applied pressures were determined using a consolidometer. All amended biosolids mixtures showed higher strength than the unamended biosolids, with mixtures containing a combination of 20% fly ash and 20% lime giving the highest (up to eightfold) increase in strength, and that with lime kiln dust and the smelter slags showing the lowest (up to twofold). The biosolids mixtures with only lime gave the second highest increase in strength (up to fourfold), but produced the largest amount of leachate, with higher level of dissolved calcium. The increase in strength correlated with availability of calcium oxide in the mixtures which lead to calcium carbonate formation, accompanied with higher leachate production and settlement during consolidation. Copper, nickel and zinc concentrations increased with alkaline additives and corresponded to higher pH and DOC levels. Nonetheless, concentrations were within the New Zealand regulatory limits for Class A landfills. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Cadmium uptake by tobacco as affected by liming, N form, and year of cultivation

    International Nuclear Information System (INIS)

    Tsadilas, C.D.; Karaivazoglou, N.A.; Tsotsolis, N.C.; Stamatiadis, S.; Samaras, V.

    2005-01-01

    Tobacco is able to accumulate cadmium and reduction of cadmium content can reduce health hazards to smokers. Soil pH and form of N fertilizers are among the factors affecting Cd uptake by tobacco. This hypothesis was tested in an acid soil in northern Greece by a four year field experiment. The variability of Cd uptake by tobacco was attributed to the variation of soil Cd availability as affected by soil pH. Liming with 3000 kg Ca(OH) 2 ha -1 increased soil pH by 0.8 units and decreased extractable with DTPA soil and leaf Cd by 40% and 35%, respectively. The ammonium fertilizer caused the opposite, but weaker, effects. Liming reduced soil Cd more in the ammonium treatment than in nitrate or combined N treatments. The year of cultivation strongly affected soil and leaf Cd. Four years after tobacco cultivation, soil pH was reduced by 0.5 units, whereas soil and leaf Cd reduction was more than 60% in the limed treatments. Liming affected Cd uptake only in the first three years of cultivation. - Liming and N form affect Cd uptake by Virginia tobacco which contributes significantly to the great reduction of extractable soil Cd after three years of continuous cultivation

  11. Impacts of fresh lime juice and peel on atherosclerosis progression in an animal model.

    Science.gov (United States)

    Boshtam, Maryam; Asgary, Sedigheh; Moshtaghian, Jamal; Naderi, Gholamali; Jafari-Dinani, Narges

    2013-11-01

    The main protective role of antioxidants in the progression of atherosclerosis has been shown in some studies. Therefore, this project evaluated the effects of Citrus aurantifolia (Christm) juice and peel on antioxidant activity and atherosclerosis progression in rabbits receiving a hypercholesterolemic diet. Forty white New Zealand male rabbits were randomly allocated to four groups. All groups were on hypercholesterolemic diet for two months. While the first group was considered as the hypercholesterolemic control, groups 2 and 3 (intervention groups) received 5 ml/day lime juice and 1 g/day dried lime peel powder, respectively. Group 4 was fed a normal diet (normal control). Before and after the study, weight was measured and a fasting blood specimen was taken from the rabbits. Serum lipids analyses and antioxidant activity evaluations were then performed. The rabbits' aorta and coronary arteries were separated and the presence of fatty streaks was studied. Comparing to the hypercholesterolemic control group (-25.2 ± 7.0), only the plasma total antioxidant capacity change was significantly more in rabbits supplemented with lime juice (16.3 ± 14.7) and peel (8.6 ± 7.1) (P = 0.008). The presence of fatty streaks in coronary arteries and aorta of the intervention groups [juice (0.2 ± 0.01); peel (0.0 ± 0.00)] was significantly decreased compared to the hypercholesterolemic control group (1.2 ± 0.4) (P lime peel is more effective than lime juice.

  12. Application and properties of pure lime façades - case study

    Directory of Open Access Journals (Sweden)

    Violeta Bokan Bosiljkov

    2008-01-01

    Full Text Available The paper presents experiences obtained during application and testing of different pure lime façades that could be successfully used in restoration of historical buildings in Slovenia. The lime façade consists of a rendering layer (rough mortar, a finishing layer (fine mortar and a protective layer of lime wash. For the design of the mortars different industrially and traditionally produced limes were chosen, based on the results of preliminary studies of the authors and experiences of a small enterprise (SE involved in the study. The façade layers were applied to the most problematic northern wall of the historic chapel made from rubble masonry. The chapel belongs to the castle Crnelo, built at the end of the 17th century in the village Turnše, not far from Ljubljana, the capital of Slovenia. The façade layers were made by skilled workers of SE, with about one year time difference between application of rendering and finishing layers, and with a protective layer of coloured lime wash applied to one to three day old finishing layers. On the rendering layers, visual inspection, water absorption tests and determination of carbonation depth were carried out before subsequent finishing layers were applied. The same on-site tests were carried out also on finished façade layers. So far, parallel to the on-site tests, compressive and water absorption tests on prisms prepared from rough mortars were carried out in laboratory.

  13. Specification and time required for the application of a lime-based render inside historic buildings

    Directory of Open Access Journals (Sweden)

    Vasco Peixoto de Freitas

    2008-01-01

    Full Text Available Intervention in ancient buildings with historical and architectural value requires traditional techniques, such as the use of lime mortars for internal and external wall renderings. In order to ensure the desired performance, these rendering mortars must be rigorously specified and quality controls have to be performed during application. The choice of mortar composition should take account of factors such as compatibility with the substrate, mechanical requirements and water behaviour. The construction schedule, which used to be considered a second order variable, nowadays plays a decisive role in the selection of the rendering technique, given its effects upon costs. How should lime-based mortars be specified? How much time is required for the application and curing of a lime-based render? This paper reflects upon the feasibility of using traditional lime mortars in three-layer renders inside churches and monasteries under adverse hygrothermal conditions and when time is critical. A case study is presented in which internal lime mortar renderings were applied in a church in Northern Portugal, where the very high relative humidity meant that several months were necessary before the drying process was complete.

  14. Cyclic softening as a parameter for prediction of remnant creep rupture life of a Indian reduced activation ferritic–martensitic (IN-RAFM) steel subjected to fatigue exposures

    Energy Technology Data Exchange (ETDEWEB)

    Sarkar, Aritra, E-mail: aritra@igcar.gov.in [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102, Tamil Nadu (India); Vijayanand, V.D.; Shankar, Vani; Parameswaran, P.; Sandhya, R.; Laha, K.; Mathew, M.D.; Jayakumar, T. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102, Tamil Nadu (India); Rajendrakumar, E. [Institute for Plasma Research, Bhat, Gandhinagar, Gujarat (India)

    2014-12-15

    Sequential fatigue-creep tests were conducted on Indian reduced activation ferritic–martensitic steel at 823 K leading to sharp decrease in residual creep life with increase in prior fatigue exposures. Extensive recovery of martensitic-lath structure taking place during fatigue deformation, manifested as cyclic softening in the cyclic stress response, shortens the residual creep life. Based on the experimental results, cyclic softening occurring during fatigue stage can be correlated with residual creep life, evolving in an empirical model which predicts residual creep life as a function of cyclic softening. Predicted creep lives for specimens pre-cycled at various strain amplitudes are explained on the basis of mechanism of cyclic softening.

  15. Effects of watershed and in-stream liming on macroinvertebrate communities in acidified tributaries to an Adirondack lake

    Science.gov (United States)

    George, Scott D.; Baldigo, Barry P.; Lawrence, Gregory B.; Fuller, Randall L.

    2018-01-01

    Liming techniques are being explored as a means to accelerate the recovery of aquatic biota from decades of acid deposition in many regions. The preservation or restoration of native sportfish populations has typically been the impetus for liming programs, and as such, less attention has been given to its effects on other biological assemblages such as macroinvertebrates. Furthermore, the differing effects of various lime application strategies such as in-stream and watershed applications are not well understood. In 2012, a program was initiated using in-stream and aerial (whole-watershed) liming to improve water quality and Brook Trout (Salvelinus fontinalis) recruitment in three acidified tributaries of a high-elevation Adirondack lake in New York State. Concurrently, macroinvertebrates were sampled annually between 2013 and 2016 at 3 treated sites and 3 untreated reference sites to assess the effects of each liming technique on this community. Despite improvements in water chemistry in all three limed streams, our results generally suggest that neither liming technique succeeded in improving the condition of macroinvertebrate communities. The watershed application caused an immediate and unsustained decrease in the density of macroinvertebrates and increase in the proportion of sensitive taxa. These changes were driven primarily by a one-year 71 percent reduction of the acid-tolerant Leuctra stoneflies and likely represent an initial chemistry shock from the lime application rather than a recovery response. The in-stream applications appeared to reduce the density of macroinvertebrates, particularly in one stream where undissolved lime covered the natural substrate. The close proximity of our study sites to the in-stream application points (50 and 1230 m) may partly explain these negative effects. Our results are consistent with prior studies of in-stream liming which indicate that this technique often fails to restore macroinvertebrate communities to a pre

  16. Characterization of major ripening events during softening in grape: turgor, sugar accumulation, abscisic acid metabolism, colour development, and their relationship with growth.

    Science.gov (United States)

    Castellarin, Simone D; Gambetta, Gregory A; Wada, Hiroshi; Krasnow, Mark N; Cramer, Grant R; Peterlunger, Enrico; Shackel, Kenneth A; Matthews, Mark A

    2016-02-01

    Along with sugar accumulation and colour development, softening is an important physiological change during the onset of ripening in fruits. In this work, we investigated the relationships among major events during softening in grape (Vitis vinifera L.) by quantifying elasticity in individual berries. In addition, we delayed softening and inhibited sugar accumulation using a mechanical growth-preventing treatment in order to identify processes that are sugar and/or growth dependent. Ripening processes commenced on various days after anthesis, but always at similarly low elasticity and turgor. Much of the softening occurred in the absence of other changes in berry physiology investigated here. Several genes encoding key cell wall-modifying enzymes were not up-regulated until softening was largely completed, suggesting softening may result primarily from decreases in turgor. Similarly, there was no decrease in solute potential, increase in sugar concentration, or colour development until elasticity and turgor were near minimum values, and these processes were inhibited when berry growth was prevented. Increases in abscisic acid occurred early during softening and in the absence of significant expression of the V. vinifera 9-cis-epoxycarotenoid dioxygenases. However, these increases were coincident with decreases in the abscisic acid catabolite diphasic acid, indicating that initial increases in abscisic acid may result from decreases in catabolism and/or exogenous import. These data suggest that softening, decreases in turgor, and increases in abscisic acid represent some of the earliest events during the onset of ripening. Later, physical growth, further increases in abscisic acid, and the accumulation of sugar are integral for colour development. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

  17. Differences in the rheological properties of calcitic and dolomitic lime slurries: influence of particle characteristics and practical implications in lime-based mortar manufacturing

    Directory of Open Access Journals (Sweden)

    Arizzi, A.

    2012-06-01

    Full Text Available The study of the rheological properties of lime suspensions is a useful means to evaluate the workability of lime mortars. In this work, we studied the flow behaviour of two industrial hydrated limes, one of calcitic and the other of dolomitic composition, by means of two types of rheometer with different geometry and setup mode. The obtained results were interpreted taking into account the differences in microstructure and surface properties of the suspended particles. Calcitic lime dry particles are formed by angular and polydisperse clusters and, once dispersed in water, they behave like thixotropic materials. On the other hand, the dolomitic lime is formed by nanoparticles and small round cluster and it shows a pronounced plastic behaviour in suspension. This fundamental difference between the two materials explains the traditional preference for dolomitic lime mortars for plastering and rendering applications.

    El estudio de las propiedades reológicas de suspensiones de cal es una herramienta muy útil para evaluar la trabajabilidad de morteros de cal. En este trabajo se ha estudiado el comportamiento en suspensión de dos cales hidratadas, de composición calcítica y dolomítica, mediante dos tipos de reómetros con geometría y modalidades distintas de medida. Los resultados obtenidos se han interpretado teniendo en cuenta las diferencias en la microestructura y las propiedades de superficie de las partículas en suspensión. Las partículas de cal calcítica están formadas por aglomerados angulares y polidispersos y, una vez dispersadas en agua, presentan un comportamiento tixotrópico. Por su parte, la cal dolomítica está formada por nanopartículas y pequeños agregados redondeados y muestra en suspensión un pronunciado comportamiento plástico. Esta importante diferencia entre las dos cales explica la preferencia tradicional de morteros de cal dolomítica para aplicaciones en revocos.

  18. Sludge hygienization: Helminth eggs destruction by lime treatment Ascaris eggs as model

    Energy Technology Data Exchange (ETDEWEB)

    Banas, S.; Schwartzbrod, J. [Lab. de Chimie Physique et Microbiologie de l' Environnement, Nancy (France); Remy, M. [Lhoist, on behalf of the European Lime Assoication (EuLA), Bruessel (Germany); Boehm, R. [Univ. Hohenheim, Stuttgart (Germany); Verfuerden, M. [Fels-Werke GmbH, im Namen des Bundesverbandes der Deutschen Kalkindustrie (BVK), Koeln (Germany)

    2003-07-01

    Most pathogens in the raw sewage are concentrated into the sewage sludge. They can be separated into four categories: viruses, bacteria, protozoa and larger parasites such as human roundworms, tapeworms and liver flukes. Such micro-organisms can cause disease in humans, the transmission occurring in several ways e.g. by inhaling sludge aerosols or dust, by eating vegetables or fruits contaminated by sludge, drinking water contaminated by run-off or by eating meat from livestock infected by grazing pastures fertilised with sludge. The presence of helminth eggs in urban sludge may constitute a sanitary risk when used as agricultural fertiliser. To avoid any contamination, the efficiency of a certain number of sludge hygienization processes must be tested. One of these involves decontamination with quicklime. The Ascaris egg inactivation by liming with lime milk, slaked lime and quicklime is studied in a series of sludges coming from slaughterhouses. (orig.)

  19. Effect of K-fertilization, liming and placement on crop uptake of cesium and strontium

    International Nuclear Information System (INIS)

    Haak, E.

    1985-01-01

    remedial measures to reduce crop uptake of cesium and strontium under Swedish field conditions have been investigated in micro plot experiments. For cesium the effect of K-fertilization was studied on three soils with oats, peas and mustard and, in combination with placement, on two other soils with wheat, barley and rape. For strontium the effect of liming was studied on three soils with oats, barley and peas and, in combination with placement, on two other soils with wheat, oats, barley and peas. In this paper results are summarized for the grain products. Deep placement of nuclides in combination with K-fertilization and liming reduced the crop uptake of cesium and strontium by a factor of 10 and 4, respectively. On the basis of the experimental results, the practical advantages of K-fertilization and liming, as well as deep ploughing of surface contaminated land are discussed

  20. Environment-Friendly Control of Pear Scab and Rust Using Lime Sulfur

    Directory of Open Access Journals (Sweden)

    Ju Hoon Cha

    2018-03-01

    Full Text Available Pear scab and rust are the major diseases causing severe epidemics in organic cultivation of pear trees. Incidences of pear scab and rust were compared in organically managed plots and conventionally managed plots to obtain optimum application schedule of environment-friendly control agents in organically managed plots. Organically cultural practice with 10 time-applications of lime sulfur and Bordeaux mixture showed higher than 40% of control efficacies of pear scab and rust compared to conventionally cultural practice. Organically cultural practice with 8 time-applications of lime sulfur considering weather condition showed higher than 30% of control efficacies of pear scab compared to conventionally cultural practice. The results suggest that proper application of environment-friendly control agents such as lime sulfur considering weather condition will enable effective control of the major diseases for organic cultivation of pear.

  1. Mechanical Performance of Asphalt Mortar Containing Hydrated Lime and EAFSS at Low and High Temperatures.

    Science.gov (United States)

    Moon, Ki Hoon; Falchetto, Augusto Cannone; Wang, Di; Riccardi, Chiara; Wistuba, Michael P

    2017-07-03

    In this paper, the possibility of improving the global response of asphalt materials for pavement applications through the use of hydrated lime and Electric Arc-Furnace Steel Slag (EAFSS) was investigated. For this purpose, a set of asphalt mortars was prepared by mixing two different asphalt binders with fine granite aggregate together with hydrated lime or EAFSS at three different percentages. Bending Beam Rheometer (BBR) creep tests and Dynamic Shear Rheometer (DSR) complex modulus tests were performed to evaluate the material response both at low and high temperature. Then, the rheological Huet model was fitted to the BBR creep results for estimating the impact of filler content on the model parameters. It was found that an addition of hydrated lime and EAFSS up to 10% and 5%, respectively, results in satisfactory low-temperature performance with a substantial improvement of the high-temperature behavior.

  2. Response of mercury in an Adirondack (NY, USA) forest stream to watershed lime application

    Science.gov (United States)

    Millard, Geoffrey D.; Driscoll, Charles T.; Burns, Douglas; Montesdeoca, Mario R.; Murray, Karen

    2018-01-01

    Surface waters in Europe and North America previously impacted by acid deposition are recovering in conjunction with declining precursor emissions since the 1980s. Lime has been applied to some impacted watersheds to accelerate recovery. The response to liming can be considered a proxy for future recovery from acid deposition. Increases in dissolved organic carbon concentrations have been observed in surface waters in response to increased pH associated with recovery from acid deposition. Although not previously described, recovery-related increases in dissolved organic carbon could drive increases in mercury concentrations and loads because of the affinity of mercury for dissolved organic matter. We used a before–after impact-response approach to describe the response of stream mercury cycling to the application of lime to the watershed of a small stream in the Adirondack Mountains of New York, USA. Dissolved organic carbon, total mercury and methylmercury concentrations increased

  3. Mechanical Performance of Asphalt Mortar Containing Hydrated Lime and EAFSS at Low and High Temperatures

    Directory of Open Access Journals (Sweden)

    Ki Hoon Moon

    2017-07-01

    Full Text Available In this paper, the possibility of improving the global response of asphalt materials for pavement applications through the use of hydrated lime and Electric Arc-Furnace Steel Slag (EAFSS was investigated. For this purpose, a set of asphalt mortars was prepared by mixing two different asphalt binders with fine granite aggregate together with hydrated lime or EAFSS at three different percentages. Bending Beam Rheometer (BBR creep tests and Dynamic Shear Rheometer (DSR complex modulus tests were performed to evaluate the material response both at low and high temperature. Then, the rheological Huet model was fitted to the BBR creep results for estimating the impact of filler content on the model parameters. It was found that an addition of hydrated lime and EAFSS up to 10% and 5%, respectively, results in satisfactory low-temperature performance with a substantial improvement of the high-temperature behavior.

  4. Distillation of shale and other bituminous substances. [shale granules wetted, mixed with lime, heated; sulfur recovered

    Energy Technology Data Exchange (ETDEWEB)

    Noad, J

    1912-09-23

    A process is described for the treatment of shale and other bituminous substances containing sulfur and recovering desulfurized distillates. The process consists of first grinding the shale and mixing the granules obtained with a convenient liquid. The shale granules coated or covered with liquid and mixed with slacked lime are fed into a retort with a series of steps or their equivalent, made to descend, step by step, in such manner that they are continually agitated and heated. The volatile constituents escape through the coating or sheath of lime and are carried away at the upper part of the retort to a convenient condensing apparatus, the sulfur being retained by the sheath of lime and is discharged at the bottom of the retort with the spent shale and other impurities.

  5. Analysis of cubic and orthorhombic C3A hydration in presence of gypsum and lime

    KAUST Repository

    Kirchheim, A. P.

    2009-02-26

    Field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) have been used to study the microstructural changes and phase development that take place during the hydration of cubic (pure) and orthorhombic (Na-doped) tricalcium aluminate (C3A) and gypsum in the absence and presence of lime. The results demonstrate that important differences occur in the hydration of each C3A polymorph and gypsum when no lime is added; orthorhombic C3A reacts faster with gypsum than the cubic phase, forming longer ettringite needles; however, the presence of lime slows down the formation of ettringite in the orthorhombic sample. Additional rheometric tests showed the possible effects on the setting time in these cementitious mixes.

  6. Analysis of cubic and orthorhombic C3A hydration in presence of gypsum and lime

    KAUST Repository

    Kirchheim, A. P.; Fernà ndez-Altable, V.; Monteiro, P. J. M.; Dal Molin, D. C. C.; Casanova, I.

    2009-01-01

    Field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) have been used to study the microstructural changes and phase development that take place during the hydration of cubic (pure) and orthorhombic (Na-doped) tricalcium aluminate (C3A) and gypsum in the absence and presence of lime. The results demonstrate that important differences occur in the hydration of each C3A polymorph and gypsum when no lime is added; orthorhombic C3A reacts faster with gypsum than the cubic phase, forming longer ettringite needles; however, the presence of lime slows down the formation of ettringite in the orthorhombic sample. Additional rheometric tests showed the possible effects on the setting time in these cementitious mixes.

  7. Performance of Portland cement mixes containing silica fume and mixed with lime-water

    Directory of Open Access Journals (Sweden)

    Metwally A.A. Abd Elaty

    2014-12-01

    Test results show that using lime-water in mixing enhances consistency degree compared to the corresponding control mixes. Furthermore, it delays both initial and final setting times compared with traditional water due to the common ion effect principles. Moreover, combined use of lime-water and silica fume enhances the pozzolanic reaction that was identified by the strength development at both early and later ages. The existence of CH crystals for higher percentages of silica fume (up to 30% for further reaction at later ages was observed by XRD results. Moreover, combined use of silica fume and lime-water ensures a high alkaline media around steel bars from the moment of ingredients mixing as long as later ages despite of pozzolanic reaction that was identified from results of chloride attack.

  8. Effect of Lime Addition Methods on Performance Related Properties of Asphalt Concrete Mixture

    Directory of Open Access Journals (Sweden)

    Amjad Hamd Khalil Albayati

    2016-09-01

    Full Text Available In the recent years, some of the newly constructed asphalt concrete pavements in Baghdad as well as other cities across Iraq showed premature failures with consequential negative impact on both roadway safety and economy. Frequently, load associated mode of failure (rutting and fatigue as well as, occasionally, moisture damage in some poorly drained sections are the main failure types found in those newly constructed road. In this research, hydrated lime was introduced into asphalt concrete mixtures of wearing course in two methods. The first one was the addition of dry lime on dry aggregate and the second one was the addition of dry lime on saturated surface dry aggregate moisturized by 2.0 to 3.0 percent of water. For each type of addition, five different percentages of lime as a partial replacement of ordinary limestone mineral filler were used; these were; 1.0, 1.5, 2.0, 2.5, and 3 percent by weight of aggregate besides a control mixture that did not contain lime. Marshall Mix design method was used and the performance properties of moisture damage, resilient modulus, permanent deformation and fatigue characteristics were evaluated using indirect tensile strength, uniaxial repeated loading and repeated flexural beam tests. Also, VESYS5W software was implemented to evaluate the pavements performance in terms of rut depth and fatigue area for a typical pavement structure. The main conclusion withdrawn from this research revealed that the use of 2.5 percent hydrated lime in dry addition method and wet addition method showed an improved fatigue and permanent deformation characteristics, lower moisture susceptibility and high resilient modulus.

  9. Impact of lime treated soils performance on design of earthfill dikes

    Directory of Open Access Journals (Sweden)

    Nerincx Nicolas

    2016-01-01

    Full Text Available Nowadays soil treatment with lime in civil engineering is widespread in many countries on all continents, within several construction fields. The interest of the hydraulic works community regarding this technique is currently growing. It has been indeed shown during the last decade that appropriate treatment technologies provide lime treated soils with high level properties such as excellent homogeneity, low permeability, internal and external erosion resistance and mechanical stability. Those have been shown in laboratory and for some properties with full scale experiments. The so conferred soil properties can lead to innovative earthfill dams and dikes designs by addressing some of the typical designer’s problems, such as stability, watertightness, internal erosion, surface protection and flood control. However, lime treated soil external erosion resistance is still to be quantified in the field for proper designing and dimensioning of lime treated soil external erosion protection or spillways. With this purpose, an experimental earthfill dike has been built along the river Vidourle (France in July 2015, in the frame of the French R&D program “DigueELITE”. This 50 m long and 3,5 m high dike is made of lime treated silt and is provided with sensors (succion, water content and temperature and piezometer in order to be monitored. It will also be tested against surface erosion. The final objective of this R&D program is to provide guidelines for designing innovative overflow resistant earthfill dikes. This article describes the performance reached by lime treated soils and associated design requirements and application; the experimental dike construction and lessons learned; the monitoring program; the dike design perspectives opened by soil treatment.

  10. Terrestrial liming benefits birds in an acidified forest in the northeast.

    Science.gov (United States)

    Pabian, Sarah E; Brittingham, Margaret C

    2007-12-01

    Studies in Europe have reported negative effects of acid deposition on forest birds, and research in North America has identified links between forest bird abundance and rates of acid deposition. We examined the bird community in an acidified forest in central Pennsylvania (USA) and evaluated the effects of terrestrial lime application on birds. We used a before-after control-impact (BACI) study design, with one year of observation before (2003) and three years after lime application (2004, 2005, and 2006). Between the 2003 and 2004 field seasons, 4500 kg/ha of dolomitic lime were applied to two of four 100-ha watersheds. Each year, we monitored bird abundance and Ovenbird (Seiurus aurocapilla) eggshell thickness and territory size. Soil and snail abundance data were also collected. The bird community and territory size results indicated that the study area may be providing low-quality habitat for forest birds, perhaps as a result of acid deposition. We found lower forest bird abundances than have been found in less acidified areas of Pennsylvania, and larger Ovenbird territory sizes than have been found in other studies. We found a significant positive relationship between soil calcium and bird abundance, indicating that soil calcium may affect bird abundance. Liming increased soil calcium and pH and led to increased snail and bird abundances. After liming, bird abundance was positively related to snail abundance. No significant changes occurred in Ovenbird territory size or eggshell thickness. Our results suggest that acid deposition could be responsible for reduced bird abundance, and that liming is a potential mitigation technique.

  11. Impacts of fresh lime juice and peel on atherosclerosis progression in an animal model

    Directory of Open Access Journals (Sweden)

    Maryam Boshtam

    2013-11-01

    Full Text Available BACKGROUND: The main protective role of antioxidants in the progression of atherosclerosis has been shown in some studies. Therefore, this project evaluated the effects of Citrus aurantifolia (Christm juice and peel on antioxidant activity and atherosclerosis progression in rabbits receiving a hypercholesterolemic diet. METHODS: Forty white New Zealand male rabbits were randomly allocated to four groups. All groups were on hypercholesterolemic diet for two months. While the first group was considered as the hypercholesterolemic control, groups 2 and 3 (intervention groups received 5 ml/day lime juice and 1 g/day dried lime peel powder, respectively. Group 4 was fed a normal diet (normal control. Before and after the study, weight was measured and a fasting blood specimen was taken from the rabbits. Serum lipids analyses and antioxidant activity evaluations were then performed. The rabbits’ aorta and coronary arteries were separated and the presence of fatty streaks was studied. RESULTS: Comparing to the hypercholesterolemic control group (-25.2 ± 7.0, only the plasma total antioxidant capacity change was significantly more in rabbits supplemented with lime juice (16.3 ± 14.7 and peel (8.6 ± 7.1 (P = 0.008. The presence of fatty streaks in coronary arteries and aorta of the intervention groups [juice (0.2 ± 0.01; peel (0.0 ± 0.00] was significantly decreased compared to the hypercholesterolemic control group (1.2 ± 0.4 (P < 0.001. CONCLUSION: Based on our findings, Citrus aurantifolia peel and juice increase plasma antioxidant capacity in rabbits, and can thus prevent or decelerate the process of atherogenesis. However, lime peel is more effective than lime juice.   Keywords: Animal, Atherosclerosis, Atherogenic Diet, Fatty Streak, Intervention, Lime    Normal 0 false false false EN-US X-NONE AR-SA

  12. THE LIME PURIFICATION OF SUGAR –CONTAINING SOLUTION USING HIGH VISCOSITY COLLOIDAL SOLUTIONS

    Directory of Open Access Journals (Sweden)

    K. V.

    2015-12-01

    Full Text Available Aim of the work was to determine the efficiency of combined application of lime and high-viscous suspensions, containing the aluminium nanoparticles as a precursor in treatment of sugar-containing solutions. At the first stage the aluminium nanopowder, encapsulated into a salt matrix, was produced by the combined precipitation from a gas phase of metal and halogenide of alkali metal (NaCl. For the long-term stabilization of aluminum nanoparticles the method, developed by the authors, for dispersing these powders in the composition of polyethylene glycols was used, providing the colloidal solution of high viscosity (gel. At the second stage, as an object of investigation a juice of sugar beet, produced in the laboratory conditions by water extracting from the beet chips, was applied. In the produced juice the main characteristics of its quality were determined: the content of solids, sucrose, its purity was calculated (ratio of sucrose to solids content, in%. The content of protein and pectin components was also determined (as the main components of the colloidal fraction of the diffusion juice. Conventionally, as a basic reagent for the process of a lime pretreatment a lime milk of 1.18 g/cm3 density, prepared by liming the burned lime using hot water, was used. During the experiments the effectiveness of reagents, containing aluminum in nanoform, on the degree of removal of the colloidal dispersion substances in the process of juice purification in sugar beet production and improvement of its quality, is shown. However, the obtained results show that, depending on the method of producing, the additional reagents with aluminium nanoparticles have different effect on change of diffusion juice purity in the process of its treatment by the lime milk.

  13. Copper, nickel and zinc phytoavailability in an oxisol amended with sewage sludge and liming

    Directory of Open Access Journals (Sweden)

    Martins Adão Luiz Castanheiro

    2003-01-01

    Full Text Available Contents of heavy metal on agricultural soils have been raised by land applications of sewage sludge and may constitute a hazard to plants, animals and humans. A field experiment was carried out from 1983 to 1987, to evaluate the long-term effect of sewage sludge application, with and without liming, on heavy metal accumulation and availability in a Rhodic Hapludox soil grown with maize (HMD 7974 hybrid. Trials were set up in a completely randomized blocks design with four replications. Each block was split in two bands, one with and another without liming. The sludge was applied in each band at rates: 0, 20, 40, 60 and 80 Mg ha-1 (dry basis in a single application; and 40, 60 and 80 Mg ha-1 split in two, three and four equal yearly applications, respectively. The soil was sampled for chemical analysis each year after harvest. Soil samples were analysed for Cu, Ni and Zn in extracts obtained with DTPA and Mehlich-3 solutions, and in extracts obtained by digestion with nitric-perchloric acid (total metal contents, using an inductively coupled plasma (ICP spectrometer. In general, Zn, Cu and Ni concentrations in DTPA and Mehlich-3 extracts increased linearly with sludge application. Total Cu and Zn concentrations increased when sludge was applied, whereas total Ni concentrations were not affected. Both extractants were suitable to evaluate Cu and Zn availability to corn in the soil treated with sewage sludge. Liming reduced the DTPA extractability of Zn. DTPA-extractable Cu concentrations were not significantly affected by liming. Mehlich-3-extractable Cu and Zn concentrations increased with liming. Only DTPA extractant indicated reduction of Ni concentrations in the soil after liming.

  14. Preparation of Lime by Roasting the Limestone Deposits of Strezovci (Republic of Kosovo and Its Use for the Aluminothermic Production of Calcium Metal

    Directory of Open Access Journals (Sweden)

    Hoda, S.

    2013-03-01

    Full Text Available The goal of producing and processing limestone ore (mostly CaCO3 is to obtain high-quality refractory materials based on lime (CaO. Lime is the raw material for obtaining calcium metal as a strategic and fundamental component in lead metallurgy (production of refined lead, Pb-Ca alloys in the battery and cable industry, ferroalloys production with the addition of silicon and calcium, production of alloy steel and high-quality steel. This paper explores the preparation of lime by roasting the limestone deposits of Strezovci (Republic of Kosovo and its use for obtaining calcium through the aluminothermic process. Through research and analysis of the chemical composition of certain types of lime, its suitabi- lity for obtaining calcium metal was determined, and by analyzing the samples of the slag, determined was the possibility of its use in the production of fire-resistant cement for which the evaluation is needed. Based on previous research, the following was chosen: optimal composition of the cast, volume of added reducing agents, and conditions of the reduction process performance: temperature-time and initial vacuum. According to the authors’ knowledge, not one Southeast European country has applied this method, and it includes the use of by-products (slag, which can cause environmental pollution. The goal of this research was to prepare lime by roasting limestone of domestic origin in order to obtain calcium metal through the aluminothermic process. The procedure of calcium metal production includes the following operations: decarbonatization of limestone ore (CaCO3 , grinding of the obtained lime (CaO, homogenization of CaO and alumina, agglomeration, and aluminothermic reduction in vacuum furnaces. For the efficiency of the process, the most important technological operations are decarbonatization and reduction, provided the other operations are performed correctly. The estimated total world capacity for production of calcium metal is 25

  15. Long-term effects of liming and fertilization with N, P and K on ground vegetation, forest growth and soil chemistry of a Scots pine stand (Pinus sylvestris) in central Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Forsell, E.

    1997-12-31

    The present study was performed in a pine forest liming and fertilization experiment situated in central Sweden, started in 1959. The main objective was to investigate how the floristical composition changed due to different treatments during the period 1959-1996 and in particular since the latest investigation in 1981. Treatments including nitrogen and lime had the most important impact on both the species composition as well as on mean cover while effects by treatments including only phosphorous and potassium were less pronounced. It could be concluded that the main effects on the floristical composition by different treatments recorded in 1981 and 1996 were similar. However, the additional fertilization made since the last investigation in 1981 have led to more pronounced effects on floristic cover. Calluna vulgaris and Vaccinium vitis-idaea e.g. reacted negatively on nitrogen fertilization, while they were positively affected by lime. Vaccinium myrtillus reacted in the opposite way. These reactions were because of different preferences of nitrogen availability. V. Myrtillus prefers a nutrient rich environment while C. Vulgaris and V. Vitis-idaea prefer nutrient poor environments. Liming causes increased microbial activity which immobilise nitrogen. The added nitrogen during 1982-1990 made the effects more pronounced. The changes in floristical cover were linked to changes in soil chemistry and also the treatment effects on tree growth were analysed. The soil chemistry had not changed much concerning pH or base saturation since 1981, but the continued addition of nitrogen decreased the C/N-ratio in the humus layer. Tree growth was most affected by nitrogen which resulted in an almost immediately increased growth rate, while lime, phosphorous and potassium had a negative effect during the first years and then slightly increased Examination paper 1997:3. 34 refs, 23 figs, 16 tabs

  16. SYSTEMATIC FIELD SURVEY ON LIMES TRANSALUTANUS. SĂPATA CASE

    Directory of Open Access Journals (Sweden)

    Eugen S. Teodor

    2017-07-01

    Full Text Available Two adjoined forts and their surroundings, elements of the 3rd century Roman frontier in Dacia – Limes Transalutanus, which were last archaeologically investigated in 1930, were recently systematic surface surveyed, resulting in the identification of the associated civilian settlement in what seemed, at first glance, as an unexpected location, more distant than other military vici the team had previously identified along the same frontier line.Not only the limits of the settlement at Săpata were established, but also the density of occupation and territory division into various functional areas, allowing further interpretations regarding the network of ancient local roads and a better understanding of the way in which the Romans adjusted their built facilities to available resources (water or exploited the strategical features of the relief.Using an efficient, quick and rather inexpensive combination of survey methods (field walking and measurements of the magnetic susceptibility of the soil applied on a 4.8 ha surface, followed by pottery typological and spatial distribution analysis, the investigation team tried to mitigate the challenging vegetation situation, adjusting likewise to the limited resources of a scheduled research project.  Data relevance was increased by applying statistical corrections and using complementary investigation methods in order to cover the various available types of land (relief, vegetation, visibility; while data integration was ensured employing a unitary spatial gridded system for fieldwork and also by relating the obtained results to the high resolution digital terrain model of the sites obtained during UAV photogrammetric aerial survey.In particular, the study takes the opportunity opened by the analysis of the Roman Age pottery found in Săpata vicus to debate on the significance of the traditional, yet not unitary perceived, scholarly division between ‘Chilia-Militari’ ware (dwelling on Dacian

  17. Geotechnical and Physico-Chemical Characterization of Low Lime Fly Ashes

    Directory of Open Access Journals (Sweden)

    Arif Ali Baig Moghal

    2013-01-01

    Full Text Available In order to explore the possibility of using low-lime fly ashes, the physical and chemical properties which have a direct bearing on their geotechnical and geoenvironmental behaviors have been investigated. In this paper, two types of low-lime fly ashes, originating from India, have been used. A brief account of various methods adopted in characterizing their physical, chemical, and geotechnical properties is presented. The relative importance of each of these properties in enhancing the bulk applicability of fly ashes has been brought out.

  18. No tillage and liming reduce greenhouse gas emissions from poorly drained agricultural soils in Mediterranean regions

    International Nuclear Information System (INIS)

    García-Marco, Sonia; Abalos, Diego; Espejo, Rafael; Vallejo, Antonio; Mariscal-Sancho, Ignacio

    2016-01-01

    No tillage (NT) has been associated to increased N_2O emission from poorly drained agricultural soils. This is the case for soils with a low permeable Bt horizon, which generates a perched water layer after water addition (via rainfall or irrigation) over a long period of time. Moreover, these soils often have problems of acidity and require liming application to sustain crop productivity; changes in soil pH have large implications for the production and consumption of soil greenhouse gas (GHG) emissions. Here, we assessed in a split-plot design the individual and interactive effects of tillage practices (conventional tillage (CT) vs. NT) and liming (Ca-amendment vs. not-amendment) on N_2O and CH_4 emissions from poorly drained acidic soils, over a field experiment with a rainfed triticale crop. Soil mineral N concentrations, pH, temperature, moisture, water soluble organic carbon, GHG fluxes and denitrification capacity were measured during the experiment. Tillage increased N_2O emissions by 68% compared to NT and generally led to higher CH_4 emissions; both effects were due to the higher soil moisture content under CT plots. Under CT, liming reduced N_2O emissions by 61% whereas no effect was observed under NT. Under both CT and NT, CH_4 oxidation was enhanced after liming application due to decreased Al"3"+ toxicity. Based on our results, NT should be promoted as a means to improve soil physical properties and concurrently reduce N_2O and CH_4 emissions. Raising the soil pH via liming has positive effects on crop yield; here we show that it may also serve to mitigate CH_4 emissions and, under CT, abate N_2O emissions. - Highlights: • The effect of tillage and liming on GHG was studied in poorly drained acidic soils. • NT reduced N_2O emissions, global warming potential and greenhouse gases intensity. • Liming reduced N_2O and CH_4 emissions under CT; no effect was observed under NT. • NT and liming provide an opportunity for N_2O and CH_4 mitigation.

  19. Arsenic immobilization by calcium-arsenic precipitates in lime treated soils

    International Nuclear Information System (INIS)

    Moon, Deok Hyun; Dermatas, Dimitris; Menounou, Nektaria

    2004-01-01

    Lime-based stabilization/solidification (S/S) can be an effective remediation alternative for the immobilization of arsenic (As) in contaminated soils and sludges. However, the exact immobilization mechanism has not been well established. Based on previous research, As immobilization could be attributed to sorption and/or inclusion in pozzolanic reaction products and/or the formation of calcium-arsenic (Ca-As) precipitates. In this study, suspensions of lime-As and lime-As-kaolinite were studied in an attempt to elucidate the controlling mechanism of As immobilization in lime treated soils. Aqueous lime-As suspensions (slurries) with varying Ca/As molar ratios (1:1, 1.5:1, 2:1, 2.5:1 and 4:1) were prepared and soluble As concentrations were determined. X-Ray diffraction (XRD) analyses were used to establish the resulting mineralogy of crystalline precipitate formation. Depending on the redox state of the As source, different As precipitates were identified. When As (III) was used, the main precipitate formation was Ca-As-O. With As(V) as the source, Ca 4 (OH) 2 (AsO 4 ) 2 ·4H 2 O formed at Ca/As molar ratios greater than 1:1. A significant increase in As (III) immobilization was observed at Ca/As molar ratios greater than 1:1. Similarly, a substantial increase in As (V) immobilization was noted at Ca/As molar ratios greater than or equal to 2.5:1. This observation was also confirmed by XRD. Lime-As-kaolinite slurries were also prepared at different Ca/As molar ratios. These slurries were used to specifically investigate the possibility of forming pozzolanic reaction products. Such products would immobilize As by sorption and/or inclusion along with the formations of different As precipitates. Toxicity Characteristic Leaching Procedure (TCLP) tests were used to evaluate As leachability in these slurries. XRD analyses revealed no pozzolanic reaction product formation. Instead, As immobilization was found to be precipitation controlled. The same Ca-As precipitate, Ca

  20. Effect of hydrated lime on compressive strength mortar of fly ash laterite soil geopolymer mortar

    Science.gov (United States)

    Wangsa, F. A.; Tjaronge, M. W.; Djamaluddin, A. R.; Muhiddin, A. B.

    2017-11-01

    This paper explored the suitability of fly ash, hydrated lime, and laterite soil with several activator (sodium hydroxide and sodium tiosulfate) to produce geopolymer mortar. Furthermore, the heat that released by hydrated lime was used instead of oven curing. In order to produce geopolymer mortar without oven curing, three variations of curing condition has been applied. Based on the result, all the curing condition showed that the hardener mortar can be produced and exhibited the increasing of compressive strength of geopolymer mortar from 3 days to 7 days without oven curing.

  1. Kinetics of dissolution of a biocide soda-lime glass powder containing silver nanoparticles

    International Nuclear Information System (INIS)

    Esteban-Tejeda, L.; Silva, A. C. da; Mello-Castanho, S. R.; Pacharroman, C.; Moya, J. S.

    2013-01-01

    In the present study we have studied the lixiviation kinetics of silver nanoparticles, as well as the solubility of a particulate system ( 2 lixiviation followed a Jander model (α 2 /4 ≈ Kt). It has been proven that nanostructured soda-lime glass/nAg composed by particles <30 μm with a 20 wt% of silver are a strong biocide versus Gram-positive, Gram-negative bacteria and yeasts. This soda-lime glass/nAg acts as a perfect dispenser of silver nanoparticles to the liquid media, avoiding the fast increasing of its concentration over the toxicity limit for human cells and for the environment.

  2. First experimental results and simulation for gas optimisation of the MART-LIME detector

    International Nuclear Information System (INIS)

    Bazzano, A.; Brunetti, M.T.; Cocchi, M.; Hall, C.J.; Lewis, R.A.; Natalucci, L.; Ortuno-Prados, F.; Ubertini, P.

    1996-01-01

    A large area high pressure multi-wire proportional counter (MWPC), with both spatial and spectroscopic capabilities, is being jointly developed by the Istituto di Astrofisica Spaziale (IAS), CNR, Frascati, Italy and the Daresbury Laboratory (DL), Warrington, UK as part of the MART-LIME telescope. Recent test results (October-December 1995) carried out at the DL facilities are presented. A brief study, by means of a simulation program, on the possible gas mixtures to be employed in the MART-LIME detector is also reported. The results of the simulation are compared with the experimental data obtained from the tests. (orig.)

  3. A theory manual for multi-physics code coupling in LIME.

    Energy Technology Data Exchange (ETDEWEB)

    Belcourt, Noel; Bartlett, Roscoe Ainsworth; Pawlowski, Roger Patrick; Schmidt, Rodney Cannon; Hooper, Russell Warren

    2011-03-01

    The Lightweight Integrating Multi-physics Environment (LIME) is a software package for creating multi-physics simulation codes. Its primary application space is when computer codes are currently available to solve different parts of a multi-physics problem and now need to be coupled with other such codes. In this report we define a common domain language for discussing multi-physics coupling and describe the basic theory associated with multiphysics coupling algorithms that are to be supported in LIME. We provide an assessment of coupling techniques for both steady-state and time dependent coupled systems. Example couplings are also demonstrated.

  4. No tillage and liming reduce greenhouse gas emissions from poorly drained agricultural soils in Mediterranean regions

    Energy Technology Data Exchange (ETDEWEB)

    García-Marco, Sonia, E-mail: sonia.garcia@upm.es [Departamento de Química y Tecnología de los Alimentos, E.T.S.I. Agronómica, Alimentaria y de Biosistemas, Universidad Politécnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Abalos, Diego, E-mail: diego.abalosrodriguez@wur.nl [Departamento de Química y Tecnología de los Alimentos, E.T.S.I. Agronómica, Alimentaria y de Biosistemas, Universidad Politécnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Espejo, Rafael, E-mail: rafael.espejo@upm.es [Departamento de Producción Agraria, E.T.S.I. Agronómica, Alimentaria y de Biosistemas, Universidad Politécnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Vallejo, Antonio, E-mail: antonio.vallejo@upm.es [Departamento de Química y Tecnología de los Alimentos, E.T.S.I. Agronómica, Alimentaria y de Biosistemas, Universidad Politécnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Mariscal-Sancho, Ignacio, E-mail: i.mariscal@upm.es [Departamento de Producción Agraria, E.T.S.I. Agronómica, Alimentaria y de Biosistemas, Universidad Politécnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain)

    2016-10-01

    No tillage (NT) has been associated to increased N{sub 2}O emission from poorly drained agricultural soils. This is the case for soils with a low permeable Bt horizon, which generates a perched water layer after water addition (via rainfall or irrigation) over a long period of time. Moreover, these soils often have problems of acidity and require liming application to sustain crop productivity; changes in soil pH have large implications for the production and consumption of soil greenhouse gas (GHG) emissions. Here, we assessed in a split-plot design the individual and interactive effects of tillage practices (conventional tillage (CT) vs. NT) and liming (Ca-amendment vs. not-amendment) on N{sub 2}O and CH{sub 4} emissions from poorly drained acidic soils, over a field experiment with a rainfed triticale crop. Soil mineral N concentrations, pH, temperature, moisture, water soluble organic carbon, GHG fluxes and denitrification capacity were measured during the experiment. Tillage increased N{sub 2}O emissions by 68% compared to NT and generally led to higher CH{sub 4} emissions; both effects were due to the higher soil moisture content under CT plots. Under CT, liming reduced N{sub 2}O emissions by 61% whereas no effect was observed under NT. Under both CT and NT, CH{sub 4} oxidation was enhanced after liming application due to decreased Al{sup 3+} toxicity. Based on our results, NT should be promoted as a means to improve soil physical properties and concurrently reduce N{sub 2}O and CH{sub 4} emissions. Raising the soil pH via liming has positive effects on crop yield; here we show that it may also serve to mitigate CH{sub 4} emissions and, under CT, abate N{sub 2}O emissions. - Highlights: • The effect of tillage and liming on GHG was studied in poorly drained acidic soils. • NT reduced N{sub 2}O emissions, global warming potential and greenhouse gases intensity. • Liming reduced N{sub 2}O and CH{sub 4} emissions under CT; no effect was observed under NT

  5. Soil acidification and liming in grassland production and grassland soil fertility in Slovenia

    Directory of Open Access Journals (Sweden)

    Jure ČOP

    2015-12-01

    Full Text Available This paper reviews the evidences on grassland soil acidity and liming in relation to soil processes and herbage production. There is also an outline of the present state of soil acidity and acidity-related traits – contents of organic matter (OM, phosphorus (P and potassium (K in Slovene grassland. In grassland, soil acidification is an ongoing process under humid climate conditions. It is mainly driven by leaching of nutrients, net loss of cations due to retention in livestock products, use of physiologically acid fertilizers, acid rain and N2 fixation. This process is reduced by strong pH buffering capacity of the soil and by physiologically basic fertilizers. Acid grassland soils in Slovenia are widely distributed in spite of the fact that 44% of the total land has developed from a carbonate parent material. Of the 1713 grassland soil samples analysed during 2005-2007 45% were regarded as acid ones (pH < 5.5; in KCl, 57% as soils with very low P status (˂ 6 mg P2O5/100 g soil and 22% as soils with very low K status (˂ 10 mg K2O/100 soil. Increased content of soil organic matter was identified for alpine pastures (˃ 10 % OM in 44% of samples, mainly as a result of low decomposition rate. Liming of acid grassland soils did not always reflect in a higher herbage yield. The cause for this inefficiency is plant composition of grassland. Thus, many grassland plants with relatively high production potential have adapted to acid soil conditions. To illustrate the inconsistent liming effect three researches are reviewed. In the first two researches liming along with fertilizer application did not increase the yield comparing to the fertilized control while in the third research the increase amounted 26 %. Liming improves considerably botanical composition of the acid grassland (e.g. sward where Common Bent – Agrostis tenuis Sibth. – prevails and thus indirectly affects palatability and nutritive value of herbage. Grassland liming has a weak

  6. Use of wasted foundry sand (WFS) as a partial substitute for silica in a soda lime glass

    International Nuclear Information System (INIS)

    Martin, A.C.; Ueno, O.K.; Folgueras, M.V.

    2016-01-01

    The waste foundry sand (WFS) is the main waste generates in foundry industries. Studies in the literature suggest the use of WFS in different materials, such as concrete, brick or asphalt. This work aims to partially replace the silica of a soda-lime glass by the WFS. The waste foundry sand has in its composition elements such as iron and aluminum that can affect the glass quality, which justifies the residue processing to reduce the impurity content. The treatments, that included mechanical agitation and thermal treatment, resulted in a slight decrease in the percent of iron with consequent increase of the silica content. After treatment, some sands were incorporated into the glass, that showed green color but with lower absorption intensity for the sand with less iron content. It was observed that it's possible to obtain glasses using WFS, however, there is difficulty in color controlling. (author

  7. Reaction softening by dissolution–precipitation creep in a retrograde greenschist facies ductile shear zone, New Hampshire, USA

    Science.gov (United States)

    McAleer, Ryan J.; Bish, David L.; Kunk, Michael J.; Sicard, Karri R.; Valley, Peter M.; Walsh, Gregory J.; Wathen, Bryan A.; Wintsch, R.P.

    2016-01-01

    We describe strain localization by a mixed process of reaction and microstructural softening in a lower greenschist facies ductile fault zone that transposes and replaces middle to upper amphibolite facies fabrics and mineral assemblages in the host schist of the Littleton Formation near Claremont, New Hampshire. Here, Na-poor muscovite and chlorite progressively replace first staurolite, then garnet, and finally biotite porphyroblasts as the core of the fault zone is approached. Across the transect, higher grade fabric-forming Na-rich muscovite is also progressively replaced by fabric-forming Na-poor muscovite. The mineralogy of the new phyllonitic fault-rock produced is dominated by Na-poor muscovite and chlorite together with late albite porphyroblasts. The replacement of the amphibolite facies porphyroblasts by muscovite and chlorite is pseudomorphic in some samples and shows that the chemical metastability of the porphyroblasts is sufficient to drive replacement. In contrast, element mapping shows that fabric-forming Na-rich muscovite is selectively replaced at high-strain microstructural sites, indicating that strain energy played an important role in activating the dissolution of the compositionally metastable muscovite. The replacement of strong, high-grade porphyroblasts by weaker Na-poor muscovite and chlorite constitutes reaction softening. The crystallization of parallel and contiguous mica in the retrograde foliation at the expense of the earlier and locally crenulated Na-rich muscovite-defined foliation destroys not only the metastable high-grade mineralogy, but also its stronger geometry. This process constitutes both reaction and microstructural softening. The deformation mechanism here was thus one of dissolution–precipitation creep, activated at considerably lower stresses than might be predicted in quartzofeldspathic rocks at the same lower greenschist facies conditions.

  8. Transcriptome analysis and ultrastructure observation reveal that hawthorn fruit softening is due to cellulose/hemicellulose degradation

    Directory of Open Access Journals (Sweden)

    Jiayu Xu

    2016-10-01

    Full Text Available Softening, a common phenomenon in many fruits, is a well coordinated and genetically determined process. However, the process of flesh softening during ripening has rarely been described in hawthorn. In this study, we found that ‘Ruanrou Shanlihong 3 Hao’ fruits became softer during ripening, whereas ‘Qiu JinXing’ fruits remained hard. At late developmental stages, the firmness of ‘Ruanrou Shanlihong 3 Hao’ fruits rapidly declined, and that of ‘Qiu JinXing’ fruits remained essentially unchanged. According to transmission electron microscopy (TEM, the middle lamella of ‘Qiu JinXing’ and ‘Ruanrou Shanlihong 3 Hao’ fruit flesh was largely degraded as the fruits matured. Microfilaments in ‘Qiu JinXing’ flesh were arranged close together and were deep in color, whereas those in ‘Ruanrou Shanlihong 3 Hao’ fruit flesh were arranged loosely, partially degraded and light in color. RNA-Seq analysis yielded approximately 46.72 Gb of clean data and 72,837 unigenes. Galactose metabolism and pentose and glucuronate interconversions are involved in cell wall metabolism, play an important role in hawthorn texture. We identified 85 unigenes related to the cell wall between hard- and soft-fleshed hawthorn fruits. Based on data analysis and real-time PCR, we suggest that β-GAL and PE4 have important functions in early fruit softening. The genes Ffase, Gns, α-GAL, PE63, XTH and CWP, which are involved in cell wall degradation, are responsible for the different textures of hawthorn fruits. Thus, we hypothesize that the different textures of ‘Qiu JinXing’ and ‘Ruanrou Shanlihong 3 Hao’ fruits at maturity mainly result from cellulose/hemicelluloses degradation rather than from lamella degradation. Overall, we propose that different types of hydrolytic enzymes in cells interact to degrade the cell wall, resulting in ultramicroscopic Structure changes in the cell wall and, consequently, fruit softening. These results provide

  9. Study of Post-Peak Strain Softening Mechanical Behaviour of Rock Material Based on Hoek–Brown Criterion

    OpenAIRE

    Qibin Lin; Ping Cao; Peixin Wang

    2018-01-01

    In order to build the post-peak strain softening model of rock, the evolution laws of rock parameters m,s were obtained by using the evolutionary mode of piecewise linear function regarding the maximum principle stress. Based on the nonlinear Hoek–Brown criterion, the analytical relationship of the rock strength parameters m,s, cohesion c, and friction angle φ has been developed by theoretical derivation. According to the analysis on the four different types of rock, it is found that, within ...

  10. Nanosecond (ns) laser transfer of silver nanoparticles from silver-exchanged soda-lime glass to transparent soda-lime glass and shock waves formation

    International Nuclear Information System (INIS)

    Sow, Mohamed Chérif; Blondeau, Jean-Philippe; Sagot, Nadine; Ollier, Nadège; Tite, Teddy

    2015-01-01

    Highlights: • Silver nanoparticles growth by nanosecond laser irradiation of silver exchanged soda-lime glasses. • Silver nanoparticles transfer. • Nanosecond laser induced shock waves formation on glass. - Abstract: In this contribution, we showed for the first time in our knowledge a single-step process for silver clusters and nanoparticles growth and transfer from silver-exchanged soda-lime glass to un-exchanged soda-lime glass (transparent glass in visible and NIR domain) by nanosecond (ns) laser irradiation. The transferred silver nanoparticles in transparent glass are strongly linked to the glass surface. In addition, we point out the formation of shock waves, with selective silver clustering on the top wave. This technique provides an alternative and simple way to obtain metallic nanoparticles in different media which can be traversed by laser wavelength used. Moreover, this experiment is made at room temperature and air environment. It is worth noting that our technique requires a glass previously doped with the corresponding silver ions

  11. Combination of Palm Kernel Husk Ash (PKHA) and Free Lime (CaO ...

    African Journals Online (AJOL)

    Almost all admixtures used in concrete construction in Nigeria are imported. In this study, various proportions of free Lime (CaO), Palm Kernel Husk Ash (PKHA) and Ordinary Portland Cement (OPC) were mixed and the setting times of various mix proportions were determined and compared with that of only OPC.

  12. Water Utility Lime Sludge Reuse – An Environmental Sorbent for Power Utilities

    Science.gov (United States)

    Lime sludge can be used as an environmental sorbent to remove sulfur dioxide (SO2) and acid gases, by the ultra-fine CaCO3 particles, and to sequester mercury and other heavy metals, by the Natural Organic Matter and residual activated carbon. The laboratory experimental set up ...

  13. Ca(2+) and OH(-) release of ceramsites containing anorthite and gehlenite prepared from waste lime mud.

    Science.gov (United States)

    Qin, Juan; Yang, Chuanmeng; Cui, Chong; Huang, Jiantao; Hussain, Ahmad; Ma, Hailong

    2016-09-01

    Lime mud is a kind of solid waste in the papermaking industry, which has been a source of serious environmental pollution. Ceramsites containing anorthite and gehlenite were prepared from lime mud and fly ash through the solid state reaction method at 1050°C. The objective of this study was to explore the efficiency of Ca(2+) and OH(-) release and assess the phosphorus and copper ion removal performance of the ceramsites via batch experiments, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that Ca(2+) and OH(-) were released from the ceramsites due to the dissolution of anorthite, gehlenite and available lime. It is also concluded that gehlenite had stronger capacity for Ca(2+) and OH(-) release compared with anorthite. The Ca(2+) release could be fit well by the Avrami kinetic model. Increases of porosity, dosage and temperature were associated with increases in the concentrations of Ca(2+) and OH(-) released. Under different conditions, the ceramsites could maintain aqueous solutions in alkaline conditions (pH=9.3-10.9) and the release of Ca(2+) was not affected. The removal rates of phosphorus and copper ions were as high as 96.88% and 96.81%, respectively. The final pH values of both phosphorus and copper ions solutions changed slightly. The reuse of lime mud in the form of ceramsites is an effective strategy. Copyright © 2016. Published by Elsevier B.V.

  14. Effects of Lime and Concrete Waste on Vadose Zone Carbon Cycling

    DEFF Research Database (Denmark)

    Thaysen, Eike Marie; Jessen, Søren; Postma, D.

    2014-01-01

    In this work we investigate how lime and crushed concrete waste (CCW) affect carbon cycling in the vadose zone and explore whether these amendments could be employed to mitigate climate change by increasing the transport of CO2 from the atmosphere to the groundwater. We use a combination of exper......In this work we investigate how lime and crushed concrete waste (CCW) affect carbon cycling in the vadose zone and explore whether these amendments could be employed to mitigate climate change by increasing the transport of CO2 from the atmosphere to the groundwater. We use a combination...... of experimental and modeling tools to determine ongoing biogeochemical processes. Our results demonstrate that lime and CCW amendments to acid soil contribute to the climate forcing by largely increasing the soil CO2 efflux to the atmosphere. In a series of mesocosm experiments, with barley (Hordeum vulgare L.......) grown on podzolic soil material, we have investigated inorganic carbon cycling through the gaseous and liquid phases and how it is affected by different soil amendments. The mesocosm amendments comprised the addition of 0, 9.6, or 21.2 kg m−2 of crushed concrete waste (CCW) or 1 kg lime m−2. The CCW...

  15. A BETTER INDICATOR STUDY EXAMINES ALTERNATIVE BIOLOGICAL INDICATORS OF DISINFECTION IN LIME-TREATED BIOSOLIDS

    Science.gov (United States)

    Under the current regulations (CFR 503), Class B biosolids may be land applied with certain site restrictions. One method for achieving Class B status is to raise the pH of the sludge to >12 for a minimum of 2 hours with an alkaline material (normally lime). Alternately, a Clas...

  16. Fractal Loop Heat Pipe Performance Comparisons of a Soda Lime Glass and Compressed Carbon Foam Wick

    Science.gov (United States)

    Myre, David; Silk, Eric A.

    2014-01-01

    This study compares heat flux performance of a Loop Heat Pipe (LHP) wick structure fabricated from compressed carbon foam with that of a wick structure fabricated from sintered soda lime glass. Each wick was used in an LHP containing a fractal based evaporator. The Fractal Loop Heat Pipe (FLHP) was designed and manufactured by Mikros Manufacturing Inc. The compressed carbon foam wick structure was manufactured by ERG Aerospace Inc., and machined to specifications comparable to that of the initial soda lime glass wick structure. Machining of the compressed foam as well as performance testing was conducted at the United States Naval Academy. Performance testing with the sintered soda lime glass wick structures was conducted at NASA Goddard Space Flight Center. Heat input for both wick structures was supplied via cartridge heaters mounted in a copper block. The copper heater block was placed in contact with the FLHP evaporator which had a circular cross-sectional area of 0.88 cm(sup 2). Twice distilled, deionized water was used as the working fluid in both sets of experiments. Thermal performance data was obtained for three different Condenser/Subcooler temperatures under degassed conditions. Both wicks demonstrated comparable heat flux performance with a maximum of 75 W/cm observed for the soda lime glass wick and 70 W /cm(sup 2) for the compressed carbon foam wick.

  17. Historic lime-binders : An example of the 19th century Dutch military plain concrete

    NARCIS (Netherlands)

    Heinemann, H.A.; Copuroglu, O.; Nijland, T.G.

    2012-01-01

    Before the general acceptance of Portland cement as the main binder for concrete in the late 19th century, other, locally available binders were occasionally used. In the case of the Netherlands, which did not produce Portland cement, traditional lime-based binders were not uncommon. With a strong

  18. Historic lime-binders: An example of 19th Century Dutch Military plain concrete

    NARCIS (Netherlands)

    Nijland, T.G.; Copuroglu, O.; Heinemann, H.A.

    2012-01-01

    Before the general acceptance of Portland cement as the main binder for concrete in the late 19th century, other, locally available binders were occasionally used. In the case of the Netherlands, which did not produce Portland cement, traditional lime-based binders were not uncommon. With a strong

  19. Instability improvement of the subgrade soils by lime addition at Borg El-Arab, Alexandria, Egypt

    Science.gov (United States)

    El Shinawi, A.

    2017-06-01

    Subgrade soils can affect the stability of any construction elsewhere, instability problems were found at Borg El-Arab, Alexandria, Egypt. This paper investigates geoengineering properties of lime treated subgrade soils at Borg El-Arab. Basic laboratory tests, such as water content, wet and dry density, grain size, specific gravity and Atterberg limits, were performed for twenty-five samples. Moisture-density (compaction); California Bearing Ratio (CBR) and Unconfined Compression Strength (UCS) were conducted on treated and natural soils. The measured geotechnical parameters of the treated soil shows that 6% lime is good enough to stabilize the subgrade soils. It was found that by adding lime, samples shifted to coarser side, Atterberg limits values of the treated soil samples decreased and this will improve the soil to be more stable. On the other hand, Subgrade soils improved as a result of the bonding fine particles, cemented together to form larger size and reduce the plastiCity index which increase soils strength. The environmental scanning electron microscope (ESEM) is point to the presence of innovative aggregated cement materials which reduce the porosity and increase the strength as a long-term curing. Consequently, the mixture of soil with the lime has acceptable mechanical characteristics where, it composed of a high strength base or sub-base materials and this mixture considered as subgrade soil for stabilizations and mitigation the instability problems that found at Borg Al-Arab, Egypt.

  20. the suitability of lime rice husk ash cement as construction material

    African Journals Online (AJOL)

    NIJOTECH

    Enugu State University of Science and Technology, Enugu, Nigeria. ... It was therefore concluded that high percentage contents of silica, ... the Lime Rice Husk Ash cement when used as a construction material would depend ... thermal treatment of the silica in the husk .... test specimen in their moulds were stored in a.