WorldWideScience

Sample records for inboard label assembly

  1. Tip Vortex Index (TVI) Technique for Inboard Propeller Noise Estimation

    OpenAIRE

    Sezen, Savaş; Dogrul, Ali; Bal, Şakir

    2018-01-01

    Cavitating marine propeller is one of the most dominant noise sources inmarine vessels.  The aim of this study isto examine the cavitating propeller noise induced by tip vortices for twinscrew passenger vessels. To determine the noise level inboard, tip vortex index(TVI) technique has been used. This technique is an approximate method based onnumerical and experimental data. In this study, it is aimed to predict theunderwater noise of a marine propeller by applying TVI technique for ...

  2. Design of the inboard passive stabilizer for TPX

    International Nuclear Information System (INIS)

    Hoffmann, E.; Boonstra, R.; Baxi, C.B.; Chin, E.; Drees, L.; Lee, W.; Redler, K.L.; Reis, E.E.; Bialek, J.

    1995-01-01

    The Inboard Passive Stabilizer (IPS) is part of the plasma stabilizing system built into the TPX. Its purpose is to provide passive stabilization of the plasma vertical instability on short time scales. With carbon fiber composite (CFC) armor tiles it serves as a startup limiter, protects the vacuum vessel from radiation heat load during steady state operation and also functions as Neutral Beam armor. The inboard passive stabilizer is a saddle coil, constructed of a ring of copper plates, armored with CFC tiles, that surrounds the inner vacuum vessel at the midplane. The design of the plates, the support structure, cooling lines, CFC tiles and tile attach method is described. Tiles that experience only the normal heat load of 0.4 MW/m 2 are attached with mechanical fasteners. Tiles in the neutral beam shine through area are exposed to as much as 1.7 MW/m 2 and are brazed to the IPS. Significant forces are generated in the plates by the stabilization currents as well as during the frequent bakeout cycles. These plates are required to be fully remotely handled, including tile replacement, and the influence of this requirement on the design is discussed

  3. 40 CFR 1045.105 - What exhaust emission standards must my sterndrive/inboard engines meet?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What exhaust emission standards must my sterndrive/inboard engines meet? 1045.105 Section 1045.105 Protection of Environment ENVIRONMENTAL... from advertisements or other marketing materials for any engines in the engine family. (B) Your basic...

  4. 21 CFR 111.415 - What requirements apply to filling, assembling, packaging, labeling, and related operations?

    Science.gov (United States)

    2010-04-01

    ... Production and Process Control System: Requirements for Packaging and Labeling Operations § 111.415 What... unlabeled condition for future label operations, to prevent mixups; (f) Assigning a batch, lot, or control number to: (1) Each lot of packaged and labeled dietary supplement from a finished batch of dietary...

  5. Passive system for cooling the inboard region in case of a severe accident

    Energy Technology Data Exchange (ETDEWEB)

    Boccaccini, L.V. E-mail: lorenzo.boccaccini@irs.fzk.de; Gordeev, S.; Malang, S

    2002-12-01

    Previous calculations performed for different fusion reactor concepts indicated that the absence of an effective heat sink for the after-heat in the inboard region can cause concerns for the temperatures reached in case of a severe accident. This can compromise the mechanical stability of the vacuum vessel (VV) or cause unacceptable temperatures of the inboard in-vessel components with consequence in the overall safety strategy. This paper describes a design solution that has been proposed for the European Helium Cooled Solid Breeder Reactor that allows transporting the heat from the inboard to the outboard side with a passive cooling system located in the VV and based on natural circulation of liquid lead. The presented calculations aim to demonstrate the feasibility and effectiveness of such a system. The presented results have been obtained for a geometry and parameters based on a particular reactor, nevertheless the system can be adopted for a large variety of reactor concepts being relatively independent of a particular blanket or maintenance schema.

  6. Quantum dot layer-by-layer assemblies as signal amplification labels for ultrasensitive electronic detection of uropathogens.

    Science.gov (United States)

    Xiang, Yun; Zhang, Haixia; Jiang, Bingying; Chai, Yaqin; Yuan, Ruo

    2011-06-01

    The preparation and use of a new class of signal amplification label, quantum dot (QD) layer-by-layer (LBL) assembled polystyrene microsphere composite, for amplified ultrasensitive electronic detection of uropathogen-specific DNA sequences is described. The target DNA is sandwiched between the capture probes immobilized on the magnetic beads and the signaling probes conjugated to the QD LBL assembled polystyrene beads. Because of the dramatic signal amplification by the numerous QDs involved in each single DNA binding event, subfemtomolar level detection of uropathogen-specific DNA sequences is achieved, which makes our strategy among the most sensitive electronic approach for nucleic acid-based monitoring of pathogens. Our signal amplified detection scheme could be readily expanded to monitor other important biomolecules (e.g., proteins, peptides, amino acids, cells, etc.) in ultralow levels and thus holds great potential for early diagnosis of disease biomarkers.

  7. A Quantitative Approach to Evaluate the Impact of Fluorescent Labeling on Membrane-Bound HIV-Gag Assembly by Titration of Unlabeled Proteins.

    Directory of Open Access Journals (Sweden)

    Julia Gunzenhäuser

    Full Text Available The assembly process of the human immunodeficiency virus 1 (HIV-1 is driven by the viral polyprotein Gag. Fluorescence imaging of Gag protein fusions is widely performed and has revealed important information on viral assembly. Gag fusion proteins are commonly co-transfected with an unlabeled form of Gag to prevent labeling artifacts such as morphological defects and decreased infectivity. Although viral assembly is widely studied on individual cells, the efficiency of the co-transfection rescue has never been tested at the single cell level. Here, we first develop a methodology to quantify levels of unlabeled to labeled Gag in single cells using a fluorescent reporter protein for unlabeled Gag and fluorescence correlation spectroscopy. Using super-resolution imaging based on photoactivated localization microscopy (PALM combined with molecular counting we then study the nanoscale morphology of Gag clusters as a function of unlabeled to labeled Gag ratios in single cells. We show that for a given co-transfection ratio, individual cells express a wide range of protein ratios, necessitating a quantitative read-out for the expression of unlabeled Gag. Further, we show that monomerically labeled Gag assembles into membrane-bound clusters that are morphologically indistinguishable from mixtures of unlabeled and labeled Gag.

  8. Numerical Simulations of Subscale Wind Turbine Rotor Inboard Airfoils at Low Reynolds Number

    Energy Technology Data Exchange (ETDEWEB)

    Blaylock, Myra L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Thermal/ Fluid Sciences & Engineering Dept.; Maniaci, David Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Wind Energy Technologies Dept.; Resor, Brian R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Wind Energy Technologies Dept.

    2015-04-01

    New blade designs are planned to support future research campaigns at the SWiFT facility in Lubbock, Texas. The sub-scale blades will reproduce specific aerodynamic characteristics of utility-scale rotors. Reynolds numbers for megawatt-, utility-scale rotors are generally above 2-8 million. The thickness of inboard airfoils for these large rotors are typically as high as 35-40%. The thickness and the proximity to three-dimensional flow of these airfoils present design and analysis challenges, even at the full scale. However, more than a decade of experience with the airfoils in numerical simulation, in the wind tunnel, and in the field has generated confidence in their performance. Reynolds number regimes for the sub-scale rotor are significantly lower for the inboard blade, ranging from 0.7 to 1 million. Performance of the thick airfoils in this regime is uncertain because of the lack of wind tunnel data and the inherent challenge associated with numerical simulations. This report documents efforts to determine the most capable analysis tools to support these simulations in an effort to improve understanding of the aerodynamic properties of thick airfoils in this Reynolds number regime. Numerical results from various codes of four airfoils are verified against previously published wind tunnel results where data at those Reynolds numbers are available. Results are then computed for other Reynolds numbers of interest.

  9. Disulfide-induced self-assembled targets : A novel strategy for the label free colorimetric detection of DNAs/RNAs via unmodified gold nanoparticles

    NARCIS (Netherlands)

    Shokri, Ehsan; Hosseini, Morteza; Davari, Mehdi D.; Ganjali, Mohammad R.; Peppelenbosch, Maikel P.; Rezaee, Farhad

    2017-01-01

    A modified non-cross-linking gold-nanoparticles (Au-NPs) aggregation strategy has been developed for the label free colorimetric detection of DNAs/RNAs based on self-assembling target species in the presence of thiolated probes. Two complementary thiol-modified probes, each of which specifically

  10. Disulfide-induced self-assembled targets: A novel strategy for the label free colorimetric detection of DNAs/RNAs via unmodified gold nanoparticles

    NARCIS (Netherlands)

    Shokri, E. (Ehsan); M. Hosseini (Morteza); Davari, M.D. (Mehdi D.); Ganjali, M.R. (Mohammad R.); M.P. Peppelenbosch (Maikel); F. Rezaee (Farhad)

    2017-01-01

    textabstractA modified non-cross-linking gold-nanoparticles (Au-NPs) aggregation strategy has been developed for the label free colorimetric detection of DNAs/RNAs based on self-assembling target species in the presence of thiolated probes. Two complementary thiol- modified probes, each of which

  11. Assembly and selective "in synthesis" labeling of quenched fluorogenic protease substrates.

    Science.gov (United States)

    Chersi, Alberto; Ferracuti, Silvia; Falasca, Giuliana; Butler, Richard H; Fruci, Doriana

    2006-10-15

    Because impaired cellular protease activities are linked to many diseases, such as cancer, inflammation, neurodegeneration, and infection, internally quenched fluorescent peptides have recently been developed as tools for analyzing the specificities of these enzymes. Here we report convenient and cost-effective approaches for the selective "in synthesis" assembly of such substrate peptides for protease assays. Fluorescein and Dabcyl groups were covalently and selectively attached during synthesis to epsilon-amino groups of internal lysines. Functionality was then tested by digestion with leucine aminopeptidase, chymotrypsin, and microsomal vesicles. All peptides proved to be appropriate substrates of the enzymes tested and of the endogenous peptidases in the microsomal vesicles. In summary, we describe an innovative and cheap method to develop completely functional quenched fluorescent peptides that are usable in specific detection of individual proteases, in particular aminopeptidases, in both in vitro and in vivo systems.

  12. Shrink-induced graphene sensor for alpha-fetoprotein detection with low-cost self-assembly and label-free assay

    Science.gov (United States)

    Sando, Shota; Zhang, Bo; Cui, Tianhong

    2017-12-01

    Combination of shrink induced nano-composites technique and layer-by-layer (LbL) self-assembled graphene challenges controlling surface morphology. Adjusting shrink temperature achieves tunability on graphene surface morphology on shape memory polymers, and it promises to be an alternative in fields of high-surface-area conductors and molecular detection. In this study, self-assembled graphene on a shrink polymer substrate exhibits nanowrinkles after heating. Induced nanowrinkles on graphene with different shrink temperature shows distinct surface roughness and wettability. As a result, it becomes more hydrophilic with higher shrink temperatures. The tunable wettability promises to be utilized in, for example, microfluidic devices. The graphene on shrink polymer also exhibits capability of being used in sensing applications for pH and alpha-fetoprotein (AFP) detection with advantages of label free and low cost, due to self-assembly technique, easy functionalization, and antigen-antibody reaction on graphene surface. The detection limit of AFP detection is down to 1 pg/mL, and therefore the sensor also has a significant potential for biosensing as it relies on low-cost self-assembly and label-free assay.

  13. Disulfide-induced self-assembled targets: A novel strategy for the label free colorimetric detection of DNAs/RNAs via unmodified gold nanoparticles

    Science.gov (United States)

    Shokri, Ehsan; Hosseini, Morteza; Davari, Mehdi D.; Ganjali, Mohammad R.; Peppelenbosch, Maikel P.; Rezaee, Farhad

    2017-04-01

    A modified non-cross-linking gold-nanoparticles (Au-NPs) aggregation strategy has been developed for the label free colorimetric detection of DNAs/RNAs based on self-assembling target species in the presence of thiolated probes. Two complementary thiol- modified probes, each of which specifically binds at one half of the target introduced SH groups at both ends of dsDNA. Continuous disulfide bond formation at 3‧ and 5‧ terminals of targets leads to the self-assembly of dsDNAs into the sulfur- rich and flexible products with different lengths. These products have a high affinity for the surface of Au-NPs and efficiently protect the surface from salt induced aggregation. To evaluate the assay efficacy, a small part of the citrus tristeza virus (CTV) genome was targeted, leading to a detection limit of about 5 × 10-9 mol.L-1 over a linear ranged from 20 × 10-9 to 10 × 10-7 mol.L-1. This approach also exhibits good reproducibility and recovery levels in the presence of plant total RNA or human plasma total circulating RNA extracts. Self-assembled targets can be then sensitively distinguished from non-assembled or mismatched targets after gel electrophoresis. The disulfide reaction method and integrating self-assembled DNAs/RNAs targets with bare AuNPs as a sensitive indicator provide us a powerful and simple visual detection tool for a wide range of applications.

  14. Orthogonal labeling of M13 minor capsid proteins with DNA to self-assemble end-to-end multiphage structures.

    Science.gov (United States)

    Hess, Gaelen T; Guimaraes, Carla P; Spooner, Eric; Ploegh, Hidde L; Belcher, Angela M

    2013-09-20

    M13 bacteriophage has been used as a scaffold to organize materials for various applications. Building more complex multiphage devices requires precise control of interactions between the M13 capsid proteins. Toward this end, we engineered a loop structure onto the pIII capsid protein of M13 bacteriophage to enable sortase-mediated labeling reactions for C-terminal display. Combining this with N-terminal sortase-mediated labeling, we thus created a phage scaffold that can be labeled orthogonally on three capsid proteins: the body and both ends. We show that covalent attachment of different DNA oligonucleotides at the ends of the new phage structure enables formation of multiphage particles oriented in a specific order. These have potential as nanoscale scaffolds for multi-material devices.

  15. Self-assembling protein arrays on DNA chips by auto-labeling fusion proteins with a single DNA address

    NARCIS (Netherlands)

    Jongsma, M.A.; Litjens, R.H.G.M.

    2006-01-01

    The high-throughput deposition of recombinant proteins on chips, beads or biosensor devices would be greatly facilitated by the implementation of self-assembly concepts. DNA-directed immobilization via conjugation of proteins to an oligonucleotide would be preeminently suited for this purpose. Here,

  16. 49 CFR Figure 4 to Subpart E of... - Trailer Car In-Board Vestibule End Structure Conceptual Implementation 1-to Subpart E

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Trailer Car In-Board Vestibule End Structure Conceptual Implementation 1-to Subpart E 4 Figure 4 to Subpart E of Part 238 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION...

  17. Label-free and ultrasensitive electrochemiluminescence detection of microRNA based on long-range self-assembled DNA nanostructures

    International Nuclear Information System (INIS)

    Liu, Ting; Chen, Xian; Hong, Cheng-Yi; Xu, Xiao-Ping; Yang, Huang-Hao

    2014-01-01

    Electrochemiluminescence (ECL) integrates the advantages of electrochemical detection and chemiluminescent techniques. The method has received particular attention because it is highly sensitive and selective, has a wide linear range but low reagent costs. The use of nanomaterials with their unique physical and chemical properties has led to new kinds of biosensors that exhibit high sensitivity and stability. Compared to other nanomaterials, DNA nanostructures are more biocompatible, more hydrophilic, and thus less prone to nonspecific adsorption onto the electrode surface. We describe here a label-free and ultrasensitive ECL biosensor for detecting a cancer-associated microRNA at a femtomolar level. We have designed two auxiliary probes that cause the formation of a long-range self-assembly in the form of a μm-long 1-dimensional DNA concatamer. These can be used as carriers for signal amplification. The intercalation of the ECL probe Ru(phen) 3 2+ into the grooves of the concatamers leads to a substantial increase in ECL intensity. This amplified sensor shows high selectivity for discriminating complementary target and other mismatched RNAs. The biosensor enables the quantification of the expression of microRNA-21 in MCF-7 cells. It also displays very low limits of detection and provides an alternative approach for the detection of RNA or DNA detection in diagnostics and gene analysis. (author)

  18. pH-responsive diblock copolymers with two different fluorescent labels for simultaneous monitoring of micellar self-assembly and degree of protonation

    DEFF Research Database (Denmark)

    Madsen, Jeppe; Madden, George; Themistou, Efrosyni

    2018-01-01

    be correlated to changes in PDPA protonation. Diblock copolymer self-assembly to form PDPA-core aggregates occurs under these conditions, leading to pyrene fluorescence at an excitation wavelength of 405 nm. This allows direct measurement of chain aggregation, whereas using pH-responsive dyes is simply ameasure...

  19. Non-inductive current start-up and plasma equilibrium with an inboard poloidal field null by means of electron cyclotron waves in QUEST

    International Nuclear Information System (INIS)

    Zushi, H.; Hasegawa, M.; Hanada, K.; Idei, H.; Nakamura, K.; Fujisawa, A.; Nagashima, Y.; Matsuoka, K.; Tashima, S.; Ishiguro, M.; Banerjee, S.; Sharma, S.K.; Liu, H.; Nishino, N.; Isobe, M.; Toi, K.; Okamura, S.; Maekawa, T.; Fukuyama, A.; Ejiri, A.; Yamaguchi, T.; Hiratsuka, J.; Takase, Y.; Kikuchi, Mitsuru; Ueda, Y.; Mitarai, O.

    2012-11-01

    Non-inductive current start-up via relativistic electron cyclotron resonance interaction is investigated for the high ratio (∼10%) of vertical B v to toroidal B t fields and the concave field lines in the QUEST spherical tokamak. In the start-up scenario with an internal poloidal field null (IPN), the fast current start-up rate of 0.3-0.5 MA/sec and correlation with mildly relativistic electrons accelerated due to multiple ECR interaction are observed. In steady state high β p equilibrium characterized by the inboard null (R s ∼ 0.7×R 0 ) and εβ p of 1.5 is achieved, where ε, β p are the inverse aspect ratio and poloidal beta, respectively. Relaxation oscillations in this equilibrium and confinement of the energetic electrons are discussed. (author)

  20. Label-free impedimetric sensor for a ribonucleic acid oligomer specific to hepatitis C virus at a self-assembled monolayer-covered electrode.

    Science.gov (United States)

    Park, Jin-Young; Lee, Yoon-suk; Chang, Byoung-Yong; Kim, Byeang Hyean; Jeon, Sangmin; Park, Su-Moon

    2010-10-01

    A ribonucleic acid (RNA) sensor based on hybridization of its peptide nucleic acid (PNA) molecule with a target RNA oligomer of the internal ribosome entry site sequence specific to the hepatitis C virus (HCV) and the electrochemical impedance detection is described. This RNA is one of the most conservative molecules of the whole HCV RNA genome. The ammonium ion terminated PNA molecule was immobilized via its host-guest interactions with the diaza crown ring of 3-thiophene-acetamide-diaza-18-crown-6 synthesized by a simple two-step method, which forms a well-defined self-assembled monolayer (SAM) on gold. Hybridization events of the probe PNA with the target RNA were monitored by measuring charge-transfer resistances for the Fe(CN)(6)(3-/4-) redox probe using Fourier transform electrochemical impedance spectroscopy. The ratio of the resistances of the SAM-covered electrode measured before and after hybridization increased linearly with log[RNA] in the rat liver lysate with a detection limit of about 23 pM.

  1. Food Labels

    Science.gov (United States)

    ... on their food labels. When a food says "light" ("lite") or "low fat" on the label, it ... on this topic for: Teens Nutrition & Fitness Center Smart Supermarket Shopping Figuring Out Fat and Calories How ...

  2. Nutrition Labeling

    DEFF Research Database (Denmark)

    Grunert, Klaus G

    2013-01-01

    because consumers will avoid products that the label shows to be nutritionally deficient, but also because food producers will try to avoid marketing products that appear, according to the label, as nutritionally problematic, for example, because of a high content of saturated fat or salt. Nutrition......Nutrition labeling refers to the provision of information on a food product’s nutritional content on the package label. It can serve both public health and commercial purposes. From a public health perspective, the aim of nutrition labeling is to provide information that can enable consumers...... to make healthier choices when choosing food products. Nutrition labeling is thus closely linked to the notion of the informed consumer, that chooses products according to their aims, on the basis of the information at their disposal. Because many consumers are assumed to be interested in making healthy...

  3. Pesticide Labels

    Science.gov (United States)

    Pesticide labels translate results of our extensive evaluations of pesticide products into conditions, directions and precautions that define parameters for use of a pesticide with the goal of ensuring protection of human health and the environment.

  4. Electron cyclotron emission spectra in X- and O-mode polarisation at JET: Martin-Puplett interferometer, absolute calibration, revised uncertainties, inboard/outboard temperature profile, and wall properties.

    Science.gov (United States)

    Schmuck, S; Fessey, J; Boom, J E; Meneses, L; Abreu, P; Belonohy, E; Lupelli, I

    2016-09-01

    At the tokamak Joint European Torus (JET), the electron cyclotron emission spectra in O-mode and X-mode polarisations are diagnosed simultaneous in absolute terms for several harmonics with two Martin-Puplett interferometers. From the second harmonic range in X-mode polarisation, the electron temperature profile can be deduced for the outboard side (low magnetic field strength) of JET but only for some parts of the inboard side (high magnetic field strength). This spatial restriction can be bypassed, if a cutoff is not present inside the plasma for O-mode waves in the first harmonic range. Then, from this spectral domain, the profile on the entire inboard side is accessible. The profile determination relies on the new absolute and independent calibration for both interferometers. During the calibration procedure, the antenna pattern was investigated as well, and, potentially, an increase in the diagnostic responsivity of about 5% was found for the domain 100-300 GHz. This increase and other uncertainty sources are taken into account in the thorough revision of the uncertainty for the diagnostic absolute calibration. The uncertainty deduced and the convolution inherent for Fourier spectroscopy diagnostics have implications for the temperature profile inferred. Having probed the electron cyclotron emission spectra in orthogonal polarisation directions for the first harmonic range, a condition is derived for the reflection and polarisation-scrambling coefficients of the first wall on the outboard side of JET.

  5. Normal-Force and Hinge-Moment Characteristics at Transonic Speeds of Flap-Type Ailerons at Three Spanwise Locations on a 4-Percent-Thick Sweptback-Wing-Body Model and Pressure-Distribution Measurements on an Inboard Aileron

    Science.gov (United States)

    Runckel, Jack F.; Hieser, Gerald

    1961-01-01

    An investigation has been conducted at the Langley 16-foot transonic tunnel to determine the loading characteristics of flap-type ailerons located at inboard, midspan, and outboard positions on a 45 deg. sweptback-wing-body combination. Aileron normal-force and hinge-moment data have been obtained at Mach numbers from 0.80 t o 1.03, at angles of attack up to about 27 deg., and at aileron deflections between approximately -15 deg. and 15 deg. Results of the investigation indicate that the loading over the ailerons was established by the wing-flow characteristics, and the loading shapes were irregular in the transonic speed range. The spanwise location of the aileron had little effect on the values of the slope of the curves of hinge-moment coefficient against aileron deflection, but the inboard aileron had the greatest value of the slope of the curves of hinge-moment coefficient against angle of attack and the outboard aileron had the least. Hinge-moment and aileron normal-force data taken with strain-gage instrumentation are compared with data obtained with pressure measurements.

  6. GAIA: AREVAs New PWR fuel assembly design

    Energy Technology Data Exchange (ETDEWEB)

    Vollmert, N.; Gentet, G.; Louf, P.H.; Mindt, M.; O' Brian, J.; Peucker, J.

    2015-07-01

    GAIA is the label of a new PWR Fuel Assembly design developed by AREVA with the objective to provide its customers an advanced fuel assembly design regarding both robustness and performance. Since 2012 GAIA lead fuel assemblies are under irradiation in a Swedish reactor and since 2015 in a U.S. reactor. Visual inspections and examinations carried out so far during the outages confirmed the intended reliability, robustness and the performance enhancement of the design. (Author)

  7. Assembly Modulated by Particle Position and Shape: A New Concept in Self-Assembly

    DEFF Research Database (Denmark)

    Tavacoli, Joe W; Heuvingh, Julien; Du Roure, Olivia

    2017-01-01

    In this communication we outline how the bespoke arrangements and design of micron-sized superparamagnetic shapes provide levers to modulate their assembly under homogeneous magnetic fields. We label this new approach, 'assembly modulated by particle position and shape' (APPS). Specifically, usin...

  8. Food labels

    DEFF Research Database (Denmark)

    Selsøe Sørensen, Henrik; Clement, Jesper; Gabrielsen, Gorm

    2012-01-01

    The food industry develops tasty and healthy food but fails to deliver the message to all consumers. The consumers’ background knowledge is essential for how they find and decode relevant elements in the cocktail of signs which fight for attention on food labels. In this exploratory study, we find...... evidence for dividing consumers into two profiles: one relying on general food knowledge and another using knowledge related to signpost labels. In a combined eyetracking and questionnaire survey we analyse the influence of background knowledge and identify different patterns of visual attention...... for the two consumer profiles. This underlines the complexity in choosing and designing the ‘right’ elements for a food package that consumers actually look at and are able to make rational use of. In spite of any regulation of food information provided by authorities, consumers will still be confronted...

  9. Emotionel Labeling

    OpenAIRE

    Andersen, Nanna Sofie Garnov; Pedersen, Mette Kofoed; de Wit, Liv Kantsø; Ørndorf, Siri; Dissing, Celina Kyrn

    2017-01-01

    This project arises from the ideas of social constructionist theorist Kenneth J. Gergen and his presentation of Emotional Labeling as presented in his work The saturated self: Dilemmas of identity in contemporary life (1991). And on that note we are examining how emotions are being dealt with in a Danish kindergarten. We investigate what might influence the issue of emotions being taught has on children’s emotional development in everyday life. In order to do so we have conducted observations...

  10. Fuel assembly

    International Nuclear Information System (INIS)

    Abe, Hideaki; Sakai, Takao; Ishida, Tomio; Yokota, Norikatsu.

    1992-01-01

    The lower ends of a plurality of plate-like shape memory alloys are secured at the periphery of the upper inside of the handling head of a fuel assembly. As the shape memory alloy, a Cu-Zn alloy, a Ti-Pd alloy or a Fe-Ni alloy is used. When high temperature coolants flow out to the handling head, the shape memory alloy deforms by warping to the outer side more greatly toward the upper portion thereof with the temperature increase of the coolants. As the result, the shape of the flow channel of the coolants is changed so as to enlarge at the exit of the upper end of the fuel assembly. Then, the pressure loss of the coolants in the fuel assembly is decreased by the enlargement. Accordingly, the flow rate of the coolants in the fuel assembly is increased to lower the temperature of the coolants. Further, high temperature coolants and low temperature coolants are mixed sufficiently just above the fuel assembly. This can suppress the temperature fluctuation of the mixed coolants in the upper portion of the reactor core, thereby enabling to decrease a fatigue and failures of the structural components in the upper portion of the reactor core. (I.N.)

  11. Fuel assembly

    International Nuclear Information System (INIS)

    Nakatsuka, Masafumi; Matsuzuka, Ryuji.

    1976-01-01

    Object: To provide a fuel assembly which can decrease pressure loss of coolant to uniform temperature. Structure: A sectional area of a flow passage in the vicinity of an inner peripheral surface of a wrapper tube is limited over the entire length to prevent the temperature of a fuel element in the outermost peripheral portion from being excessively decreased to thereby flatten temperature distribution. To this end, a plurality of pincture-frame-like sheet metals constituting a spacer for supporting a fuel assembly, which has a plurality of fuel elements planted lengthwise and in given spaced relation within the wrapper tube, is disposed in longitudinal grooves and in stacked fashion to form a substantially honeycomb-like space in cross section. The fuel elements are inserted and supported in the space to form a fuel assembly. (Kamimura, M.)

  12. Fuel assemblies

    International Nuclear Information System (INIS)

    Nakamura, Mitsuya; Yamashita, Jun-ichi; Mochida, Takaaki.

    1986-01-01

    Purpose: To improve the fuel economy by increasing the reactivity at the latter burning stage of fuel assemblies and thereby increasing the burn-up degree. Constitution: At the later stage of the burning where the infinite multiplication factor of a fuel assembly is lowered, fuel rods are partially discharged to increase the fuel-moderator volume ratio in the fuel assembly. Then, plutonium is positively burnt by bringing the ratio near to an optimum point where the infinite multiplication factor becomes maximum and the reactivity of the fuel assembly is increased by utilizing the spectral shift effect. The number of the fuel rods to be removed is selected so as to approach the fuel-moderator atom number ratio where the infinite multiplication factor is maximum. Further, the positions where the thermal neutron fluxes are low are most effective for removing the rods and those positions between which no fuel rods are present and which are adjacent with neither the channel box nor the water rods are preferred. The rods should be removed at the time when the burning is proceeded at lest for one cycle. The reactivity is thus increased and the burn-up degree of fuels upon taking-out can be improved. (Kamimura, M.)

  13. Valve assembly

    International Nuclear Information System (INIS)

    Sandling, M.

    1981-01-01

    An improved valve assembly, used for controlling the flow of radioactive slurry, is described. Radioactive contamination of the air during removal or replacement of the valve is prevented by sucking air from the atmosphere through a portion of the structure above the valve housing. (U.K.)

  14. Fuel assemblies

    International Nuclear Information System (INIS)

    Echigoya, Hironori; Nomata, Terumitsu.

    1983-01-01

    Purpose: To render the axial distribution relatively flat. Constitution: First nuclear element comprises a fuel can made of zircalloy i.e., the metal with less neutron absorption, which is filled with a plurality of UO 2 pellets and sealed by using a lower end plug, a plenum spring and an upper end plug by means of welding. Second fuel element is formed by substituting a part of the UO 2 pellets with a water tube which is sealed with water and has a space for allowing the heat expansion. The nuclear fuel assembly is constituted by using the first and second fuel elements together. In such a structure, since water reflects neutrons and decrease their leakage to increase the temperature, reactivity is added at the upper portion of the fuel assembly to thereby flatten the axial power distribution. Accordingly, stable operation is possible only by means of deep control rods while requiring no shallow control rods. (Sekiya, K.)

  15. Assembling consumption

    DEFF Research Database (Denmark)

    Assembling Consumption marks a definitive step in the institutionalisation of qualitative business research. By gathering leading scholars and educators who study markets, marketing and consumption through the lenses of philosophy, sociology and anthropology, this book clarifies and applies...... the investigative tools offered by assemblage theory, actor-network theory and non-representational theory. Clear theoretical explanation and methodological innovation, alongside empirical applications of these emerging frameworks will offer readers new and refreshing perspectives on consumer culture and market...

  16. General Assembly

    CERN Multimedia

    Staff Association

    2016-01-01

    5th April, 2016 – Ordinary General Assembly of the Staff Association! In the first semester of each year, the Staff Association (SA) invites its members to attend and participate in the Ordinary General Assembly (OGA). This year the OGA will be held on Tuesday, April 5th 2016 from 11:00 to 12:00 in BE Auditorium, Meyrin (6-2-024). During the Ordinary General Assembly, the activity and financial reports of the SA are presented and submitted for approval to the members. This is the occasion to get a global view on the activities of the SA, its financial management, and an opportunity to express one’s opinion, including taking part in the votes. Other points are listed on the agenda, as proposed by the Staff Council. Who can vote? Only “ordinary” members (MPE) of the SA can vote. Associated members (MPA) of the SA and/or affiliated pensioners have a right to vote on those topics that are of direct interest to them. Who can give his/her opinion? The Ordinary General Asse...

  17. Fuel assembly

    International Nuclear Information System (INIS)

    Ueda, Sei; Ando, Ryohei; Mitsutake, Toru.

    1995-01-01

    The present invention concerns a fuel assembly suitable to a BWR-type reactor and improved especially with the nuclear characteristic, heat performance, hydraulic performance, dismantling or assembling performance and economical property. A part of poison rods are formed as a large-diameter/multi-region poison rods having a larger diameter than a fuel rod. A large number of fuel rods are disposed surrounding a large diameter water rod and a group of the large-diameter/multi-region poison rods in adjacent with the water rod. The large-diameter water rod has a burnable poison at the tube wall portion. At least a portion of the large-diameter poison rods has a coolant circulation portion allowing coolants to circulate therethrough. Since the large-diameter poison rods are disposed at a position of high neutron fluxes, a large neutron multiplication factor suppression effect can be provided, thereby enabling to reduce the number of burnable poison rods relative to fuels. As a result, power peaking in the fuel assembly is moderated and a greater amount of plutonium can be loaded. In addition the flow of cooling water which tends to gather around the large diameter water rod can be controlled to improve cooling performance of fuels. (N.H.)

  18. Figuring Out Food Labels

    Science.gov (United States)

    ... beware of. Using Food Labels for a Well-Balanced Diet Here are some guidelines on using food labels ... food label smarts to create a healthy, well-balanced diet. It might seem complicated at first, but it ...

  19. Understanding Food Labels

    Science.gov (United States)

    ... Healthy eating for girls Understanding food labels Understanding food labels There is lots of info on food ... need to avoid because of food allergies. Other food label terms top In addition to the Nutrition ...

  20. ULTRASONIC ASSEMBLY [REVIEW

    Directory of Open Access Journals (Sweden)

    PORAV Viorica

    2015-05-01

    Full Text Available The paper exposes the possibility of machine producesers to optimize the costs of clothes assembling. Ultrasonic systems being frequently utilized have many advantages on semi products of synthetic textile and technical textile. First of all, sewing – cutting process can be accomplished under high speeds and rate of losses can be minimized. Cutting seal applications are frequently used for underwear and sportswear. Slicing and unit cutting machines, as well as portable sealing machines are available for labeling sector. Products such as bag, pocket and cover can be sewed in a seamless manner for promotion purposes. All objects in terms of accessories are obtained in same standard. Our quilting machines are preferred in worldwide due to its threadless, high quality sealing. An alternative to the classic sewing assembly, with thread and needles is ultrasonic seaming. In ultrasonic welding, there are no connective bolts, nails, soldering materials, or adhesives necessary to bind the materials together. Ultrasonic is defined as acoustic frequencies above the range audible to the human ear. Ultrasonic frequencies are administered to the fabric from the sonotrode of bonding machine. The high frequency and powerful energy produced, when is release in one special environment, the ultrasound heating this environment. The ability to ultrasonic weld textiles and films depend on their thermoplastic contents and the desired end results. The paper defines the weld ability of more common textiles and films. The welding refers to all types of bonding and sealing, as in point bonding of fabric, or continuous sealing of film.

  1. Shingle assembly

    Science.gov (United States)

    Dinwoodie, Thomas L.

    2007-02-20

    A barrier, such as a PV module, is secured to a base by a support to create a shingle assembly with a venting region defined between the barrier and base for temperature regulation. The first edge of one base may be interengageable with the second edge of an adjacent base to be capable of resisting first and second disengaging forces oriented perpendicular to the edges and along planes oriented parallel to and perpendicular to the base. A deflector may be used to help reduce wind uplift forces.

  2. Heater assembly

    International Nuclear Information System (INIS)

    Lee, K.; Ueng, Tzoushin.

    1991-01-01

    An electrical resistance heater, installed in the H1 borehole, is used to thermally perturb the rock mass through a controlled heating and cooling cycle. Heater power levels are controlled by a Variac power transformer and are measured by wattmeters. Temperatures are measured by thermocouples on the borehole wall and on the heater assembly. Power and temperature values are recorded by the DAS described in Chapter 12. The heater assembly consists of a 3.55-m (11.6-ft) long by 20.3-cm (8-in.) O.D., Type 304 stainless steel pipe, containing a tubular hairpin heating element. The element has a heated length of 3 m (9.84 ft). The power rating of the element is 10 kW; however, we plan to operate the unit at a maximum power of only 3 kW. The heater is positioned with its midpoint directly below the axis of the P2 borehole, as shown in the borehole configuration diagram. This heater midpoint position corresponds to a distance of approximately 8.5 m (27.9 ft) from the H1 borehole collar. A schematic of the heater assembly in the borehole is shown. The distance from the borehole collar to the closest point on the assembly (the front end) is 6.5 m (21.3 ft). A high-temperature inflatable packer, used to seal the borehole for moisture collection, is positioned 50 cm (19.7 in.) ahead of the heater front end. The heater is supported and centralized within the borehole by two skids, fabricated from 25-mm (1-in.) O.D. stainless steel pipe. Thermocouples are installed at a number of locations in the H1 borehole. Four thermocouples that are attached to the heater skin monitor temperatures on the outer surface of the can, while three thermocouples that are held in place by rock sections monitor borehole wall temperatures beneath the heater. Temperatures are also monitored at the heater terminal and on the packer hardware

  3. Assembling consumption

    DEFF Research Database (Denmark)

    Assembling Consumption marks a definitive step in the institutionalisation of qualitative business research. By gathering leading scholars and educators who study markets, marketing and consumption through the lenses of philosophy, sociology and anthropology, this book clarifies and applies the i...... societies. This is an essential reading for both seasoned scholars and advanced students of markets, economies and social forms of consumption....... the investigative tools offered by assemblage theory, actor-network theory and non-representational theory. Clear theoretical explanation and methodological innovation, alongside empirical applications of these emerging frameworks will offer readers new and refreshing perspectives on consumer culture and market...

  4. Fuel assembly

    International Nuclear Information System (INIS)

    Chaki, Masao; Nishida, Koji; Karasawa, Hidetoshi; Kanazawa, Toru; Orii, Akihito; Nagayoshi, Takuji; Kashiwai, Shin-ichi; Masuhara, Yasuhiro

    1998-01-01

    The present invention concerns a fuel assembly, for a BWR type nuclear reactor, comprising fuel rods in 9 x 9 matrix. The inner width of the channel box is about 132mm and the length of the fuel rods which are not short fuel rods is about 4m. Two water rods having a circular cross section are arranged on a diagonal line in a portion of 3 x 3 matrix at the center of the fuel assembly, and two fuel rods are disposed at vacant spaces, and the number of fuel rods is 74. Eight fuel rods are determined as short fuel rods among 74 fuel rods. Assuming the fuel inventory in the short fuel rod as X(kg), and the fuel inventory in the fuel rods other than the short fuel rods as Y(kg), X and Y satisfy the relation: X + Y ≥ 173m, Y ≤ - 9.7X + 292, Y ≤ - 0.3X + 203 and X > 0. Then, even when the short fuel rods are used, the fuel inventory is increased and fuel economy can be improved. (I.N.)

  5. General Assembly

    CERN Multimedia

    Staff Association

    2016-01-01

    Mardi 5 avril à 11 h 00 BE Auditorium Meyrin (6-2-024) Conformément aux statuts de l’Association du personnel, une Assemblée générale ordinaire est organisée une fois par année (article IV.2.1). Projet d’ordre du jour : Adoption de l’ordre du jour. Approbation du procès-verbal de l’Assemblée générale ordinaire du 5 mai 2015. Présentation et approbation du rapport d’activités 2015. Présentation et approbation du rapport financier 2015. Présentation et approbation du rapport des vérificateurs aux comptes pour 2015. Programme de travail 2016. Présentation et approbation du projet de budget 2016 Approbation du taux de cotisation pour 2017. Modifications aux Statuts de l'Association du personnel proposée. Élections des membres de la Commissio...

  6. General Assembly

    CERN Multimedia

    Staff Association

    2017-01-01

    Conformément aux statuts de l’Association du personnel, une Assemblée générale ordinaire est organisée une fois par année (article IV.2.1). Projet d’ordre du jour : Adoption de l’ordre du jour. Approbation du procès-verbal de l’Assemblée générale ordinaire du 5 avril 2016. Présentation et approbation du rapport d’activités 2016. Présentation et approbation du rapport financier 2016. Présentation et approbation du rapport des vérificateurs aux comptes pour 2016. Programme de travail 2017. Présentation et approbation du projet de budget 2017 Approbation du taux de cotisation pour 2018. Modifications aux Statuts de l'Association du personnel proposées. Élections des membres de la Commission électorale. Élections des vérifica...

  7. General Assembly

    CERN Multimedia

    Staff Association

    2015-01-01

    Mardi 5 mai à 11 h 00 Salle 13-2-005 Conformément aux statuts de l’Association du personnel, une Assemblée générale ordinaire est organisée une fois par année (article IV.2.1). Projet d’ordre du jour : 1- Adoption de l’ordre du jour. 2- Approbation du procès-verbal de l’Assemblée générale ordinaire du 22 mai 2014. 3- Présentation et approbation du rapport d’activités 2014. 4- Présentation et approbation du rapport financier 2014. 5- Présentation et approbation du rapport des vérificateurs aux comptes pour 2014. 6- Programme 2015. 7- Présentation et approbation du projet de budget 2015 et taux de cotisation pour 2015. 8- Pas de modifications aux Statuts de l'Association du personnel proposée. 9- Élections des membres de la Commission é...

  8. General assembly

    CERN Multimedia

    Staff Association

    2015-01-01

    Mardi 5 mai à 11 h 00 Salle 13-2-005 Conformément aux statuts de l’Association du personnel, une Assemblée générale ordinaire est organisée une fois par année (article IV.2.1). Projet d’ordre du jour : Adoption de l’ordre du jour. Approbation du procès-verbal de l’Assemblée générale ordinaire du 22 mai 2014. Présentation et approbation du rapport d’activités 2014. Présentation et approbation du rapport financier 2014. Présentation et approbation du rapport des vérificateurs aux comptes pour 2014. Programme 2015. Présentation et approbation du projet de budget 2015 et taux de cotisation pour 2015. Pas de modifications aux Statuts de l'Association du personnel proposée. Élections des membres de la Commission électorale. &am...

  9. Fuel assembly

    International Nuclear Information System (INIS)

    Nomata, Terumitsu.

    1993-01-01

    Among fuel pellets to be loaded to fuel cans of a fuel assembly, fuel pellets having a small thermal power are charged in a region from the end of each of spacers up to about 50mm on the upstream of coolants that flow vertically at the periphery of fuel rods. Coolants at the periphery of fuel rods are heated by the heat generation, to result in voids. However, since cooling effect on the upstream of the spacers is low due to influences of the spacers. Further, since the fuel pellets disposed in the upstream region have small thermal power, a void coefficient is not increased. Even if a thermal power exceeding cooling performance should be generated, there is no worry of causing burnout in the upstream region. Even if burnout should be caused, safety margin and reliability relative to burnout are improved, to increase an allowable thermal power, thereby enabling to improve integrity and reliability of fuel rods and fuel assemblies. (N.H.)

  10. Directed Supramolecular Surface Assembly of SNAP-tag Fusion Proteins

    NARCIS (Netherlands)

    Uhlenheuer, D.A.; Wasserberg, D.; Haase, C.; Nguyen, Hoang D.; Schenkel, J.H.; Huskens, Jurriaan; Ravoo, B.J.; Jonkheijm, Pascal; Brunsveld, Luc

    2012-01-01

    Supramolecular assembly of proteins on surfaces and vesicles was investigated by site-selective incorporation of a supramolecular guest element on proteins. Fluorescent proteins were site-selectively labeled with bisadamantane by SNAP-tag technology. The assembly of the bisadamantane functionalized

  11. Mixed Map Labeling

    Directory of Open Access Journals (Sweden)

    Maarten Löffler

    2016-12-01

    Full Text Available Point feature map labeling is a geometric visualization problem, in which a set of input points must be labeled with a set of disjoint rectangles (the bounding boxes of the label texts. It is predominantly motivated by label placement in maps but it also has other visualization applications. Typically, labeling models either use internal labels, which must touch their feature point, or external (boundary labels, which are placed outside the input image and which are connected to their feature points by crossing-free leader lines. In this paper we study polynomial-time algorithms for maximizing the number of internal labels in a mixed labeling model that combines internal and external labels. The model requires that all leaders are parallel to a given orientation θ ∈ [0, 2π, the value of which influences the geometric properties and hence the running times of our algorithms.

  12. Industrial Robot Label Applicator

    OpenAIRE

    Kukasch, Kai

    2017-01-01

    The thesis deals with a project carried out for developing and setting up a robot label applicator system. The requirement was that RFID tracking labels can be applied on flexible positions, without manual effort and rearrangement, via programming. The purpose of the robot label applicator system is to increase the efficiency in production sites, where the RFID label position can change, depending on product or other reasons. New label positions should be programmed easily with a human-m...

  13. Mapping device and process for nuclear fuel assembly

    International Nuclear Information System (INIS)

    Vere, B.; Mathevon, P.

    1986-01-01

    The nuclear fuel assembly is mapped while it is loaded. The present invention proposes a simple and sure process of identification of the rods of the assembly, allowing to keep for each one all the information concerning it. The rods are installed as a regular grid in a rack by placing the rods one by one in a former, reading the label of each rod and recording its coordinates before removing the label, aligning the rack with the former, and drawing the rods from the former into the rack. A device for mapping the assembly is also claimed. The invention can be applied to a water cooled and moderated reactor [fr

  14. Fuel assembly

    International Nuclear Information System (INIS)

    Bessho, Yasunori; Ishii, Yoshihiko; Sadaoka, Noriyuki.

    1990-01-01

    Burnable poisons are disposed in the lower portions of a water rod, a channel box and a control rod guide pipe in a fuel assembly, and the amount for each of them is set to burn out in one operation cycle. Since the inner side of the water rod and the control rod guide pipe and gaps are filled with steams at the initial and the intermediate stages of the operation cycle, moderation of neutrons is delayed to harden the spectrum. On the other hand, since the burnable poisons are burnt out in the final stage of the operation cycle, γ-ray heating is not expected and since the insides of the water rod and the control rod guide pipe and the gaps are filled with water of great moderation effect, the neutron spectrum arae softened. In view of the above, void coefficient is increased to promote conversion from U-235 to Pu-239 by utilizing exothermic reaction of burnable poisons at the initial and the intermediate stages in the operation cycle and generation of voids are eliminated at the final stage where the burnable poisons are burnt out, thereby enabling effective burning of Pu-239. (N.H.)

  15. Fuel assembly

    International Nuclear Information System (INIS)

    Yamazaki, Hajime.

    1995-01-01

    In a fuel assembly having fuel rods of different length, fuel pellets of mixed oxides of uranium and plutonium are loaded to a short fuel rod. The volume ratio of a pellet-loaded portion to a plenum portion of the short fuel rod is made greater than the volume ratio of a fuel rod to which uranium fuel pellets are loaded. In addition, the volume of the plenum portion of the short fuel rod is set greater depending on the plutonium content in the loaded fuel pellets. MOX fuel pellets are loaded on the short fuel rods having a greater degree of freedom relevant to the setting for the volume of the plenum portion compared with that of a long rod fuel, and the volume of the plenum portion is ensured greater depending on the plutonium content. Even if a large amount of FP gas and He gas are discharged from the MOX fuels compared with that from the uranium fuels, the internal pressure of the MOX fuel rod during operation is maintained substantially identical with that of the uranium fuel rod, so that a risk of generating excess stresses applied to the fuel cladding tubes and rupture of fuels are greatly reduced. (N.H.)

  16. Fuel assembly

    International Nuclear Information System (INIS)

    Nakajima, Akiyoshi; Bessho, Yasunori; Aoyama, Motoo; Koyama, Jun-ichi; Hirakawa, Hiromasa; Yamashita, Jun-ichi; Hayashi, Tatsuo

    1998-01-01

    In a fuel assembly of a BWR type reactor in which a water rod of a large diameter is disposed at the central portion, the cross sectional area perpendicular to the axial direction comprises a region a of a fuel rod group facing to a wide gap water region to which a control rod is inserted, a region b of a fuel rod group disposed on the side of the wide gap water region other than the region a, a region d of a fuel rod group facing to a narrow gap water region and a region c of a fuel rod group disposed on the side of the narrow gap water region other than the region d. When comparing an amount of fission products contained in the four regions relative to that in the entire regions and average enrichment degrees of fuel rods for the four regions, the relative amount and the average enrichment degree of the fuel rod group of the region a is minimized, and the relative amount and the average enrichment degree of the fuel rod group in the region b is maximized. Then, reactor shut down margin during cold operation can be improved while flattening the power in the cross section perpendicular to the axial direction. (N.H.)

  17. Synthesizing labeled compounds

    International Nuclear Information System (INIS)

    London, R.E.; Matwiyoff, N.A.; Unkefer, C.J.; Walker, T.E.

    1983-01-01

    A metabolic study is presented of the chemical reactions provided by isotopic labeling and NMR spectroscopy. Synthesis of 13 C-labeled D-glucose, a 6-carbon sugar, involves adding a labeled nitrile group to the 5-carbon sugar D-arabinose by reaction with labeled hydrogen cyanide. The product of this reaction is then reduced and hydrolyzed to a mixture of the labeled sugars. The two sugars are separated by absorption chromotography. The synthesis of 13 C-labeled L-tyrosine, an amino acid, is also presented

  18. Soil Fumigant Labels - Dazomet

    Science.gov (United States)

    Updated labels include new safety requirements for buffer zones and related measures. Find information from the Pesticide Product Labeling System (PPLS) for products such as Basamid G, manufactured by Amvac.

  19. Soil Fumigant Labels - Chloropicrin

    Science.gov (United States)

    Search by EPA registration number, product name, or company name, and follow the link to the Pesticide Product Label System (PPLS) for details on each fumigant. Updated labels include new safety requirements for buffer zones and related measures.

  20. Semiotic labelled deductive systems

    Energy Technology Data Exchange (ETDEWEB)

    Nossum, R.T. [Imperial College of Science, Technology and Medicine, London (United Kingdom)

    1996-12-31

    We review the class of Semiotic Models put forward by Pospelov, as well as the Labelled Deductive Systems developed by Gabbay, and construct an embedding of Semiotic Models into Labelled Deductive Systems.

  1. Pesticide Product Label System

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Pesticide Product Label System (PPLS) provides a collection of pesticide product labels (Adobe PDF format) that have been approved by EPA under Section 3 of the...

  2. Mental Labels and Tattoos

    Science.gov (United States)

    Hyatt, I. Ralph

    1977-01-01

    Discusses the ease with which mental labels become imprinted in our system, six basic axioms for maintaining negative mental tattoos, and psychological processes for eliminating mental tattoos and labels. (RK)

  3. Electronic Submission of Labels

    Science.gov (United States)

    Pesticide registrants can provide draft and final labels to EPA electronically for our review as part of the pesticide registration process. The electronic submission of labels by registrants is voluntary but strongly encouraged.

  4. A Label to Regulate

    DEFF Research Database (Denmark)

    Tricoire, Aurélie; Boxenbaum, Eva; Laurent, Brice

    This paper examines the role labelling plays in the government of the contemporary economy.1Drawing on a detailed study of BBC-Effinergy, a French label for sustainable construction, we showhow the adoption and evolution of voluntary labels can be seen as emblematic of a governmentthrough experim...... experiment engaging 4 operations: stimulating market anticipations, focussing politicalconsultations, producing collective expertise and containing the regulatory transcription of the label....

  5. Assembly Modulated by Particle Position and Shape: A New Concept in Self-Assembly.

    Science.gov (United States)

    Tavacoli, Joe W; Heuvingh, Julien; Du Roure, Olivia

    2017-11-10

    In this communication we outline how the bespoke arrangements and design of micron-sized superparamagnetic shapes provide levers to modulate their assembly under homogeneous magnetic fields. We label this new approach, 'assembly modulated by particle position and shape' (APPS). Specifically, using rectangular lattices of superparamagnetic micron-sized cuboids, we construct distinct microstructures by adjusting lattice pitch and angle of array with respect to a magnetic field. Broadly, we find two modes of assembly: (1) immediate 2D jamming of the cuboids as they rotate to align with the applied field (rotation-induced jamming) and (2) aggregation via translation after their full alignment (dipole-dipole assembly). The boundary between these two assembly pathways is independent on field strength being solely a function of the cuboid's dimensions, lattice pitch, and array angle with respect to field-a relationship which we capture, along with other features of the assembly process, in a 'phase diagram'. In doing so, we set out initial design rules to build custom made assemblies. Moreover, these assemblies can be made flexible thanks to the hinged contacts of their particle building blocks. This flexibility, combined with the superparamagnetic nature of the architectures, renders our assembly method particularly appropriate for the construction of complex actuators at a scale hitherto not possible.

  6. Assembly Modulated by Particle Position and Shape: A New Concept in Self-Assembly

    Directory of Open Access Journals (Sweden)

    Joe W. Tavacoli

    2017-11-01

    Full Text Available In this communication we outline how the bespoke arrangements and design of micron-sized superparamagnetic shapes provide levers to modulate their assembly under homogeneous magnetic fields. We label this new approach, ‘assembly modulated by particle position and shape’ (APPS. Specifically, using rectangular lattices of superparamagnetic micron-sized cuboids, we construct distinct microstructures by adjusting lattice pitch and angle of array with respect to a magnetic field. Broadly, we find two modes of assembly: (1 immediate 2D jamming of the cuboids as they rotate to align with the applied field (rotation-induced jamming and (2 aggregation via translation after their full alignment (dipole-dipole assembly. The boundary between these two assembly pathways is independent on field strength being solely a function of the cuboid’s dimensions, lattice pitch, and array angle with respect to field—a relationship which we capture, along with other features of the assembly process, in a ‘phase diagram’. In doing so, we set out initial design rules to build custom made assemblies. Moreover, these assemblies can be made flexible thanks to the hinged contacts of their particle building blocks. This flexibility, combined with the superparamagnetic nature of the architectures, renders our assembly method particularly appropriate for the construction of complex actuators at a scale hitherto not possible.

  7. Chitosan biotinylation and electrodeposition for selective protein assembly.

    Science.gov (United States)

    Shi, Xiao-Wen; Liu, Yi; Lewandowski, Angela T; Wu, Li-Qun; Wu, Hsuan-Chen; Ghodssi, Reza; Rubloff, Gary W; Bentley, William E; Payne, Gregory F

    2008-05-13

    An alternative route to protein assembly at surfaces based on using the unique capabilities of biological materials for the spatially selective assembly of proteins is described. Specifically, the stimuli-responsive properties of aminopolysaccharide chitosan are combined with the molecular-recognition capabilities of biotin-streptavidin binding. Biotinylated chitosan retains its stimuli-responsive properties and is capable of electrodepositing at specific electrode addresses. Once deposited, it is capable of binding streptavidin, which can mediate the subsequent assembly of biotinylated proteins. Spatially selective protein assembly using biotinylated Protein A and fluorescently-labeled antibodies is demonstrated.

  8. Robotic Label Applicator: Design, Development and Visual Servoing Based Control

    Directory of Open Access Journals (Sweden)

    Lin Chyi-Yeu

    2016-01-01

    Full Text Available Use of robotic arms and computer vision in manufacture, and assembly process are getting more interest as flexible customization is becoming priority over mass production as frontier industry practice. In this paper an innovative label applicator as end of arm tooling (EOAT capable of dispensing and applying label stickers of various dimensions to a product is designed, fabricated and tested. The system incorporates a label dispenserapplicator and had eye-in-hand camera system, attached to 6-dof robot arm can autonomously apply a label sticker to the target position on a randomly placed product. Employing multiple advantages from different knowledge basis, mechanism design and vision based automatic control, offers this system distinctive efficiency as well as flexibility to change in manufacturing and assembly process with time and cost saving.

  9. Newnes electronics assembly handbook

    CERN Document Server

    Brindley, Keith

    2013-01-01

    Newnes Electronics Assembly Handbook: Techniques, Standards and Quality Assurance focuses on the aspects of electronic assembling. The handbook first looks at the printed circuit board (PCB). Base materials, basic mechanical properties, cleaning of assemblies, design, and PCB manufacturing processes are then explained. The text also discusses surface mounted assemblies and packaging of electromechanical assemblies, as well as the soldering process. Requirements for the soldering process; solderability and protective coatings; cleaning of PCBs; and mass solder/component reflow soldering are des

  10. Dynamics of HIV-1 assembly and release.

    Directory of Open Access Journals (Sweden)

    Sergey Ivanchenko

    2009-11-01

    Full Text Available Assembly and release of human immunodeficiency virus (HIV occur at the plasma membrane of infected cells and are driven by the Gag polyprotein. Previous studies analyzed viral morphogenesis using biochemical methods and static images, while dynamic and kinetic information has been lacking until very recently. Using a combination of wide-field and total internal reflection fluorescence microscopy, we have investigated the assembly and release of fluorescently labeled HIV-1 at the plasma membrane of living cells with high time resolution. Gag assembled into discrete clusters corresponding to single virions. Formation of multiple particles from the same site was rarely observed. Using a photoconvertible fluorescent protein fused to Gag, we determined that assembly was nucleated preferentially by Gag molecules that had recently attached to the plasma membrane or arrived directly from the cytosol. Both membrane-bound and cytosol derived Gag polyproteins contributed to the growing bud. After their initial appearance, assembly sites accumulated at the plasma membrane of individual cells over 1-2 hours. Assembly kinetics were rapid: the number of Gag molecules at a budding site increased, following a saturating exponential with a rate constant of approximately 5 x 10(-3 s(-1, corresponding to 8-9 min for 90% completion of assembly for a single virion. Release of extracellular particles was observed at approximately 1,500+/-700 s after the onset of assembly. The ability of the virus to recruit components of the cellular ESCRT machinery or to undergo proteolytic maturation, or the absence of Vpu did not significantly alter the assembly kinetics.

  11. Fuel assembly cleaning device

    International Nuclear Information System (INIS)

    Kikuchi, Akira.

    1981-01-01

    Purpose: To enable efficient and sufficient cleaning of a fuel assembly even in corners without disassembling the assembly and to effectively remove crud. Constitution: Cleaning water mixed with abrasive is injected into a fuel assembly contained within a cleaning device body to remove crud adhering to the fuel assembly. Since a coolant passage from the opening of the bottom surface is of the fuel assembly to the opening of the top surface is utilized as the cleaning water passage at this, the crud can be removed by the abrasive in the water stream even from narrow gaps of the fuel assembly. (Aizawa, K.)

  12. Labelling Fashion Markets

    OpenAIRE

    Aspers, P.

    2008-01-01

    The present article discusses how an ethical and environmental labelling system can be implemented in fashion garment markets. Consumers act in markets that provide them with more information than their limited cognitive capacity allows them to handle. Ethical and environmental labelling in markets characterized by change, such as the fashion garment market, makes decision-making even more complicated. The ethical and environmental labelling system proposed here is designed to alleviate firms...

  13. Deuterium labeled cannabinoids

    International Nuclear Information System (INIS)

    Driessen, R.A.

    1979-01-01

    Complex reactions involving ring opening, ring closure and rearrangements hamper complete understanding of the fragmentation processes in the mass spectrometric fragmentation patterns of cannabinoids. Specifically labelled compounds are very powerful tools for obtaining more insight into fragmentation mechanisms and ion structures and therefore the synthesis of specifically deuterated cannabinoids was undertaken. For this, it was necessary to investigate the preparation of cannabinoids, appropriately functionalized for specific introduction of deuterium atom labels. The results of mass spectrometry with these labelled cannabinoids are described. (Auth.)

  14. Effective sample labeling

    International Nuclear Information System (INIS)

    Rieger, J.T.; Bryce, R.W.

    1990-01-01

    Ground-water samples collected for hazardous-waste and radiological monitoring have come under strict regulatory and quality assurance requirements as a result of laws such as the Resource Conservation and Recovery Act. To comply with these laws, the labeling system used to identify environmental samples had to be upgraded to ensure proper handling and to protect collection personnel from exposure to sample contaminants and sample preservatives. The sample label now used as the Pacific Northwest Laboratory is a complete sample document. In the event other paperwork on a labeled sample were lost, the necessary information could be found on the label

  15. Bar Code Labels

    Science.gov (United States)

    1988-01-01

    American Bar Codes, Inc. developed special bar code labels for inventory control of space shuttle parts and other space system components. ABC labels are made in a company-developed anodizing aluminum process and consecutively marketed with bar code symbology and human readable numbers. They offer extreme abrasion resistance and indefinite resistance to ultraviolet radiation, capable of withstanding 700 degree temperatures without deterioration and up to 1400 degrees with special designs. They offer high resistance to salt spray, cleaning fluids and mild acids. ABC is now producing these bar code labels commercially or industrial customers who also need labels to resist harsh environments.

  16. Optical Space Telescope Assembly

    Data.gov (United States)

    National Aeronautics and Space Administration — The Optical Space Telescope Assembly (OSTA) task is to demonstrate the technology readiness of assembling large space telescopes on orbit in 2015. This task is an...

  17. Membrane module assembly

    Science.gov (United States)

    Kaschemekat, Jurgen

    1994-01-01

    A membrane module assembly adapted to provide a flow path for the incoming feed stream that forces it into prolonged heat-exchanging contact with a heating or cooling mechanism. Membrane separation processes employing the module assembly are also disclosed. The assembly is particularly useful for gas separation or pervaporation.

  18. Stable isotopes labelled compounds

    International Nuclear Information System (INIS)

    1982-09-01

    The catalogue on stable isotopes labelled compounds offers deuterium, nitrogen-15, and multiply labelled compounds. It includes: (1) conditions of sale and delivery, (2) the application of stable isotopes, (3) technical information, (4) product specifications, and (5) the complete delivery programme

  19. Sensor mount assemblies and sensor assemblies

    Science.gov (United States)

    Miller, David H [Redondo Beach, CA

    2012-04-10

    Sensor mount assemblies and sensor assemblies are provided. In an embodiment, by way of example only, a sensor mount assembly includes a busbar, a main body, a backing surface, and a first finger. The busbar has a first end and a second end. The main body is overmolded onto the busbar. The backing surface extends radially outwardly relative to the main body. The first finger extends axially from the backing surface, and the first finger has a first end, a second end, and a tooth. The first end of the first finger is disposed on the backing surface, and the tooth is formed on the second end of the first finger.

  20. Radioiodine and its labelled compounds

    International Nuclear Information System (INIS)

    Robles, Ana Maria

    1994-01-01

    Chemical characteristics and their nuclear characteristics, types of labelled molecules,labelling procedures, direct labelling with various oxidizing agents, indirect labelling with various conjugates attached to protein molecules, purification and quality control. Iodination damage.Safe handling of labelling procedures with iodine radioisotopes.Bibliography

  1. 'Naturemade' -- a new label

    International Nuclear Information System (INIS)

    Niederhaeusern, A.

    2001-01-01

    This short article discusses the introduction of the 'Naturemade' two-level labelling scheme in the Swiss electricity market, which is to help provide transparency in the market for green power and promote the building of facilities for its production. In the form of an interview with the CEO of Swissolar and the president of Greenpeace Switzerland, the pros and contras of these labels are discussed. In particular, the interview partners' opinions on the possible misuse of the less stringent label and the influence of the labels on the construction of new installations for the generation of electricity from renewable sources are presented. The basic principles of the promotional model behind the labels are listed

  2. Nuclear fuel string assembly

    International Nuclear Information System (INIS)

    Ip, A.K.; Koyanagi, K.; Tarasuk, W.R.

    1976-01-01

    A method of fabricating rodded fuels suitable for use in pressure tube type reactors and in pressure vessel type reactors is described. Fuel rods are secured as an inner and an outer sub-assembly, each rod attached between mounting rings secured to the rod ends. The two sub-assemblies are telescoped together and positioned by spaced thimbles located between them to provide precise positioning while permittng differential axial movement between the sub-assemblies. Such sub-assemblies are particularly suited for mounting as bundle strings. The method provides particular advantages in the assembly of annular-section fuel pins, which includes booster fuel containing enriched fuel material. (LL)

  3. Soldering in electronics assembly

    CERN Document Server

    Judd, Mike

    2013-01-01

    Soldering in Electronics Assembly discusses several concerns in soldering of electronic assemblies. The book is comprised of nine chapters that tackle different areas in electronic assembly soldering. Chapter 1 discusses the soldering process itself, while Chapter 2 covers the electronic assemblies. Chapter 3 talks about solders and Chapter 4 deals with flux. The text also tackles the CS and SC soldering process. The cleaning of soldered assemblies, solder quality, and standards and specifications are also discussed. The book will be of great use to professionals who deal with electronic assem

  4. Assembling method for nuclear reactor fuel assembly

    International Nuclear Information System (INIS)

    Kamiwaki, Yoshiharu; Ono, Shunji.

    1996-01-01

    Control rod guide tubes are inserted and assembled in to predetermined openings of a plurality of support lattices arranged in rows at predetermined distance. Sheath heaters are inserted to the guide tubes. The sheath heater comprises a plurality of heater elements therein which are connected to a temperature controller. The temperature of each portion of the sheath heater is controlled by the temperature controller. When the temperature of each portion of the guide tube is made uniform, MOX fuel rods are inserted to vacant openings of the support lattices. This changes the circumferential temperature of the guide tube, but the heat generation amount of each heater element is controlled suitably by the temperature controller. Accordingly, even if MOX fuel rods are inserted as a heat generation member, fuel assembly can be assembled with no assembling errors. (I.N.)

  5. Articulate fuel assembly

    International Nuclear Information System (INIS)

    Noyes, R.C.

    1978-01-01

    An articulated fuel assembly for the core of a fast spectrum reactor comprising an elongated shroud enclosing a cluster of fuel pins, a support foot assembly supporting the fuel assembly in the reactor core and an articulating connector link joining the support foot assembly and the lower end of the elongated shroud is described. The upper end of the elongated shroud and the support foot assembly are adapted to be fixedly restrained against lateral movement when the assembly is placed in the reactor core. The articulating connector link is such as to permit free lateral deflection of the lower end of the shroud relative to the upper end of the shroud and the foot assembly. Such an arrangement icreases the reliability of the fuel assembly and safely accommodates the physical distortions in the fuel assemblies caused by neutron induced swelling of the members and thermally induced expansions thereof by reducing stresses in the structural parts of the assembly and by insuring a negative reactivity for the core as the lower ends of the fuel assemblies are laterally displaced. 4 claims, 4 figures

  6. Estimation of labeling efficiency in pseudocontinuous arterial spin labeling.

    Science.gov (United States)

    Aslan, Sina; Xu, Feng; Wang, Peiying L; Uh, Jinsoo; Yezhuvath, Uma S; van Osch, Matthias; Lu, Hanzhang

    2010-03-01

    Pseudocontinuous arterial spin labeling MRI is a new arterial spin labeling technique that has the potential of combining advantages of continuous arterial spin labeling and pulsed arterial spin labeling. However, unlike continuous arterial spin labeling, the labeling process of pseudocontinuous arterial spin labeling is not strictly an adiabatic inversion and the efficiency of labeling may be subject specific. Here, three experiments were performed to study the labeling efficiency in pseudocontinuous arterial spin labeling MRI. First, the optimal labeling position was determined empirically to be approximately 84 mm below the anterior commissure-posterior commissure line in order to achieve the highest sensitivity. Second, an experimental method was developed to utilize phase-contrast velocity MRI as a normalization factor and to estimate the labeling efficiency in vivo, which was founded to be 0.86 +/- 0.06 (n = 10, mean +/- standard deviation). Third, we compared the labeling efficiency of pseudocontinuous arterial spin labeling MRI under normocapnic and hypercapnic (inhalation of 5% CO(2)) conditions and showed that a higher flow velocity in the feeding arteries resulted in a reduction in the labeling efficiency. In summary, our results suggest that labeling efficiency is a critical parameter in pseudocontinuous arterial spin labeling MRI not only in terms of achieving highest sensitivity but also in quantification of absolute cerebral blood flow in milliliters per minute per 100 g. We propose that the labeling efficiency should be estimated using phase-contrast velocity MRI on a subject-specific basis. (c) 2010 Wiley-Liss, Inc.

  7. Food Allergies: Understanding Food Labels

    Science.gov (United States)

    ... a few common questions about food label requirements. What foods are labeled? Domestic or imported packaged food is ... allergens found in flavorings, colorings or other additives. What foods aren't labeled? Fresh produce, eggs, fresh meat ...

  8. Soil Fumigant Labels - Methyl Bromide

    Science.gov (United States)

    Search soil fumigant pesticide labels by EPA registration number, product name, or company, and follow the link to The Pesticide Product Label System (PPLS) for details. Updated labels include new safety requirements for buffer zones and related measures.

  9. Radioactive labelled orgotein

    International Nuclear Information System (INIS)

    1980-01-01

    The preparation and use of radioactively labelled orgotein, i.e. water-soluble protein congeners in pure, injectable form, is described. This radiopharmaceutical is useful in scintigraphy, especially for visualization of the kidneys where the orgotein is rapidly concentrated. Details of the processes for labelling bovine orgotein with sup(99m)Tc, 60 Co, 125 I or 131 I are specified. The pharmaceutical preparation of the labelled orgotein for intravenous and parenteral administration is also described. Examples using either sup(99m)TC or 125 I-orgotein in scintiscanning dogs' kidneys are given. (UK)

  10. On Online Labeling with Polynomially Many Labels

    DEFF Research Database (Denmark)

    Babka, Martin; Bulánek, Jan; Cunat, Vladimír

    2012-01-01

    be necessary to change the labels of some items; such changes may be done at any time at unit cost for each change. The goal is to minimize the total cost. An alternative formulation of this problem is the file maintenance problem, in which the items, instead of being labeled, are maintained in sorted order...... in an array of length m, and we pay unit cost for moving an item. For the case m = cn for constant c > 1, there are known algorithms that use at most O(n log(n)2) relabelings in total [9], and it was shown recently that this is asymptotically optimal [1]. For the case of m = θ(nC) for C > 1, algorithms...

  11. Clinical applications of cells labelling

    International Nuclear Information System (INIS)

    Gonzalez, B.M.

    1994-01-01

    Blood cells labelled with radionuclides are reviewed and main applications are described. Red blood cell labelling by both random and specific principle. A table with most important clinical uses, 99mTc labelling of RBC are described pre tinning and in vivo reduction of Tc, in vitro labelling and administration of labelled RBC and in vivo modified technique. Labelled leucocytes with several 99mTc-complex radiopharmaceuticals by in vitro technique and specific monoclonal s for white cells(neutrofiles). Labelled platelets for clinical use and research by in vitro technique and in vivo labelling

  12. FDA Online Label Repository

    Data.gov (United States)

    U.S. Department of Health & Human Services — The drug labels and other drug-specific information on this Web site represent the most recent drug listing information companies have submitted to the Food and Drug...

  13. Assembly tool design

    International Nuclear Information System (INIS)

    Kanamori, Naokazu; Nakahira, Masataka; Ohkawa, Yoshinao; Tada, Eisuke; Seki, Masahiro

    1996-06-01

    The reactor core of the International Thermonuclear Experimental Reactor (ITER) is assembled with a number of large and asymmetric components within a tight tolerance in order to assure the structural integrity for various loads and to provide the tritium confinement. In addition, the assembly procedure should be compatible with remote operation since the core structures will be activated by 14-MeV neutrons once it starts operation and thus personal access will be prohibited. Accordingly, the assembly procedure and tool design are quite essential and should be designed from the beginning to facilitate remote operation. According to the ITER Design Task Agreement, the Japan Atomic Energy Research Institute (JAERI) has performed design study to develop the assembly procedures and associated tool design for the ITER tokamak assembly. This report describes outlines of the assembly tools and the remaining issues obtained in this design study. (author)

  14. Pembuatan kulit untuk label

    Directory of Open Access Journals (Sweden)

    Ign. Sunaryo

    2001-12-01

    Full Text Available Abstract This research is aimed to produce leather for label which is needed by market demand ant to disseminate this technology to industries. There were 10 sides of wet salted cow hides for this research. Those hides were divided into 3 groups, each group consisted of 3 sides that were serially tanned by 3%, 4% and 5% and one side for control. Those hides were then mixed and divided into 3 groups, each group consisted of 3 sides and were then tanned by 6%, 8% and 10% of mimosa. The rest one side was tanned by 6% chrome and 8% mimosa for control. One side of label leather was taken from market used for comparison. Organoleptical, physical and chemical leather testing were carried out in IRDLAI laboratory. The result showed that the quality of the label leather from this research were better than label leather from market. Beside this it could be found out the technology of label manufacture which could produce good quality of label leather that were tanned by 5% chrome and re-tanned by 8% of mimosa

  15. Fuel assembly storage pool

    International Nuclear Information System (INIS)

    Hiranuma, Hiroshi.

    1976-01-01

    Object: To remove limitation of the number of storage of fuel assemblies to increase the number of storage thereof so as to relatively reduce the water depth required for shielding radioactive rays. Structure: Fuel assembly storage rack containers for receiving a plurality of spent fuel assembly racks are stacked in multi-layer fashion within a storage pool filled with water for shielding radioactive rays and removing heat. (Furukawa, Y.)

  16. ex vivo DNA assembly

    Directory of Open Access Journals (Sweden)

    Adam B Fisher

    2013-10-01

    Full Text Available Even with decreasing DNA synthesis costs there remains a need for inexpensive, rapid and reliable methods for assembling synthetic DNA into larger constructs or combinatorial libraries. Advances in cloning techniques have resulted in powerful in vitro and in vivo assembly of DNA. However, monetary and time costs have limited these approaches. Here, we report an ex vivo DNA assembly method that uses cellular lysates derived from a commonly used laboratory strain of Escherichia coli for joining double-stranded DNA with short end homologies embedded within inexpensive primers. This method concurrently shortens the time and decreases costs associated with current DNA assembly methods.

  17. Target Assembly Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Target Assembly Facility integrates new armor concepts into actual armored vehicles. Featuring the capability ofmachining and cutting radioactive materials, it...

  18. Selective 'in synthesis' labeling of peptides with biotin and rhodamine.

    Science.gov (United States)

    Chersi, A; Giommi, S; Rosanò, L

    2000-04-06

    A new method is described for the selective 'in synthesis' labeling of peptides by rhodamine or biotin at a single, predetermined epsilon-amino group of a lysine residue. The alpha-amino group and other lysyl residues of the peptide remain unmodified. Peptides are assembled by the Fmoc approach, which requires mild operative conditions for the final deprotection and cleavage, and ensures little damage of the reporter group. The labeling technique involves the previous preparation of a suitable Lysine derivative, easily obtained from commercially-available protected amino acids. This new derivative, where the reporter group (biotin, or rhodamine) acts now as permanent protection of lysyl side chain functions, is then inserted into the synthesis program as a conventional protected amino acid, and linked to the preceding residue by aid of carbodiimide. A simpler, alternative method is also described for the selective 'in synthesis' labeling of peptides with N-terminal lysyl residues. Several applications of labeled peptides are reported.

  19. Genetic algorithms for map labeling

    NARCIS (Netherlands)

    Dijk, Steven Ferdinand van

    2001-01-01

    Map labeling is the cartographic problem of placing the names of features (for example cities or rivers) on the map. A good labeling has no intersections between labels. Even basic versions of the problem are NP-hard. In addition, realistic map-labeling problems deal with many cartographic

  20. European consumers and nutrition labelling

    DEFF Research Database (Denmark)

    Wills, Josephine M.; Grunert, Klaus G.; Celemín, Laura Fernández

    2009-01-01

    Nutrition labelling of food in Europe is not compulsory, unless a nutrition or health claim is made for the product. The European Commission is proposing mandatory nutrition labelling, even front of pack labelling with nutrition information. Yet, how widespread is nutrition labelling in the EU...

  1. Vertical pump assembly

    International Nuclear Information System (INIS)

    Dohnal, M.; Rosel, J.; Skarka, V.

    1988-01-01

    The mounting is described of the drive assembly of a vertical pump for nuclear power plants in areas with seismic risk. The assembly is attached to the building floor using flexible and damping elements. The design allows producing seismically resistant pumps without major design changes in the existing types of vertical pumps. (E.S.). 1 fig

  2. Assembling Transgender Moments

    Science.gov (United States)

    Greteman, Adam J.

    2017-01-01

    In this article, the author seeks to assemble moments--scholarly, popular, and aesthetic--in order to explore the possibilities that emerge as moments collect in education's encounters with the needs, struggles, and possibilities of transgender lives and practices. Assembling moments, the author argues, illustrates the value of "moments"…

  3. Extending reference assembly models

    DEFF Research Database (Denmark)

    Church, Deanna M.; Schneider, Valerie A.; Steinberg, Karyn Meltz

    2015-01-01

    The human genome reference assembly is crucial for aligning and analyzing sequence data, and for genome annotation, among other roles. However, the models and analysis assumptions that underlie the current assembly need revising to fully represent human sequence diversity. Improved analysis tools...... and updated data reporting formats are also required....

  4. Perspective: Geometrically frustrated assemblies

    Science.gov (United States)

    Grason, Gregory M.

    2016-09-01

    This perspective will overview an emerging paradigm for self-organized soft materials, geometrically frustrated assemblies, where interactions between self-assembling elements (e.g., particles, macromolecules, proteins) favor local packing motifs that are incompatible with uniform global order in the assembly. This classification applies to a broad range of material assemblies including self-twisting protein filament bundles, amyloid fibers, chiral smectics and membranes, particle-coated droplets, curved protein shells, and phase-separated lipid vesicles. In assemblies, geometric frustration leads to a host of anomalous structural and thermodynamic properties, including heterogeneous and internally stressed equilibrium structures, self-limiting assembly, and topological defects in the equilibrium assembly structures. The purpose of this perspective is to (1) highlight the unifying principles and consequences of geometric frustration in soft matter assemblies; (2) classify the known distinct modes of frustration and review corresponding experimental examples; and (3) describe outstanding questions not yet addressed about the unique properties and behaviors of this broad class of systems.

  5. Self-assembled nanostructures

    CERN Document Server

    Zhang, Jin Z; Liu, Jun; Chen, Shaowei; Liu, Gang-yu

    2003-01-01

    Nanostructures refer to materials that have relevant dimensions on the nanometer length scales and reside in the mesoscopic regime between isolated atoms and molecules in bulk matter. These materials have unique physical properties that are distinctly different from bulk materials. Self-Assembled Nanostructures provides systematic coverage of basic nanomaterials science including materials assembly and synthesis, characterization, and application. Suitable for both beginners and experts, it balances the chemistry aspects of nanomaterials with physical principles. It also highlights nanomaterial-based architectures including assembled or self-assembled systems. Filled with in-depth discussion of important applications of nano-architectures as well as potential applications ranging from physical to chemical and biological systems, Self-Assembled Nanostructures is the essential reference or text for scientists involved with nanostructures.

  6. High utilization fuel assembly

    International Nuclear Information System (INIS)

    Camden, T.M. Jr.

    1986-01-01

    A nuclear fuel assembly is described comprising an array of parallel arranged guide tubes, an inlet nozzle attached to one end of the guide tubes, an outlet nozzle attached to the other end of the guide tubes, grids having the openings therethrough attached to and spaced along the length of the guide tubes, and of parallel arranged fuel rod assemblies each having an upper end and a lower end. The fuel rod assemblies are fitted within the openings in the grids, the fuel rod assemblies being arranged axially offset relative to each adjacent fuel rod assembly and comprising an upper fuel rod and a lower axially aligned fuel rod with a gap therebetween. The gap between the fuel rods each is axially offset relative to each adjacent gap so as to eliminate an axial gap across the core

  7. Dimeric assembly of enterocyte brush border enzymes

    DEFF Research Database (Denmark)

    Danielsen, E M

    1994-01-01

    The noncovalent, dimeric assembly of small intestinal brush border enzymes was studied by sedimentation analysis in density gradients of extracts of pulse-labeled pig jejunal mucosal explants. Like aminopeptidase N (EC 3.4.11.2), sucrase-isomaltase (EC 3.2.1.48-10), aminopeptidase A (EC 3...... appearance of the liposome-reconstituted enzyme [Norén et al. (1986) J. Biol. Chem. 261, 12306-12309], showing only the inner, membrane-anchored domains of the monomers to be in close contact with one another while the outer domains are far apart. In contrast to the other brush border enzymes studied...

  8. Toward improved pregnancy labelling.

    Science.gov (United States)

    Koren, Gideon; Sakaguchi, Sachi; Klieger, Chagit; Kazmin, Alex; Osadchy, Alla; Yazdani-Brojeni, Parvaneh; Matok, Ilan

    2010-01-01

    Information about the use of a medication in pregnancy is part of overall drug labelling as prepared by the pharmaceutical company and approved by the regulators. It is aimed at assisting clinicians in prescribing, however, very few drugs are labelled for specific indications in pregnancy, since there is rarely information about the use of a drug in this condition. Recently the FDA has drafted new guidelines for the labeling of drugs in pregnancy and breastfeeding, to replace the A,B,C,D,X system that was used for more than 30 years. Here we document the use of the new system through 3 different medications; each representing a different clinical situation in pregnancy--acute infection, chronic pain, and drug use during labor. Advantages and challenges in the new system are being highlighted.

  9. Synthesis of labeled compounds

    International Nuclear Information System (INIS)

    Whaley, T.W.

    1977-01-01

    Intermediate compounds labeled with 13 C included methane, sodium cyanide, methanol, ethanol, and acetonitrile. A new method for synthesizing 15 N-labeled 4-ethylsulfonyl-1-naphthalene-sulfonamide was developed. Studies were conducted on pathways to oleic-1- 13 C acid and a second pathway investigated was based on carbonation of 8-heptadecynylmagnesium bromide with CO 2 to prepare sterolic acid. Biosynthetic preparations included glucose- 13 C from starch isolated from tobacco leaves following photosynthetic incubation with 13 CO 2 and galactose- 13 C from galactosylglycerol- 13 C from kelp. Research on growth of organisms emphasized photosynthetic growth of algae in which all cellular carbon is labeled. Preliminary experiments were performed to optimize the growth of Escherichia coli on sodium acetate- 13 C

  10. Fluorine-18 labelled compounds

    International Nuclear Information System (INIS)

    Kleijn, J.P. de

    1978-01-01

    The work presented in this thesis deals with the problems involved in the adaption of reactor-produced fluorine-18 to the synthesis of 18 F-labelled organic fluorine compounds. Several 18 F-labelling reagents were prepared and successfully applied. The limitations to the synthetic possibilities of reactor-produced fluoride- 18 become manifest in the last part of the thesis. An application to the synthesis of labelled aliphatic fluoro amino acids has appeared to be unsuccessful as yet, although some other synthetic approaches can be indicated. Seven journal articles (for which see the availability note) are used to compose the four chapters and three appendices. The connecting text gives a survey of known 18 F-compounds and methods for preparing such compounds. (Auth.)

  11. Colloidal assemblies on patterned silane layers

    Science.gov (United States)

    Jonas, Ulrich; del Campo, Aránzazu; Krüger, Christian; Glasser, Gunnar; Boos, Diana

    2002-01-01

    The site-selective assembly of colloidal polymer particles onto laterally patterned silane layers was studied as a model system for the object assembly process at mesoscale dimensions. The structured silane monolayers on silicon oxide substrates were fabricated by a combination of liquid- and gas-phase deposition of different trialkoxysilanes with a photolithographic patterning technique. By using this method various types of surface functionalizations such as regions with amino functions next to areas of the bare silica surface or positively charged regions of a quaternary ammonium silane surrounded by a hydrophobic octadecylsilane film could be obtained. Furthermore, a triethoxysilane with a photoprotected amino group was synthesized, which allowed direct photopatterning after monolayer preparation, leading to free NH2 groups at the irradiated regions. The different silane monolayer patterns were used to study the surface assembly behavior of carboxylated methacrylate particles by optical and scanning electron microscopy. In dependence of the assembly conditions (different surface functionalizations, pH, and drying conditions), a selective preference of the particles for a specific surface type versus others was found. Site-specific colloid adsorption could be observed also on the photosensitive silane layers after local deprotection with light. From the photosensitive silane and positively charged ammonium silane, molecularly mixed monolayers were prepared, which allowed particle adsorption and photoactivation within the same monolayer as shown by fluorescence labeling. PMID:11959954

  12. Environmental Labels and Declarations

    DEFF Research Database (Denmark)

    Frydendal, Jeppe; Hansen, Lisbeth; Bonou, Alexandra

    2017-01-01

    Based on the terminology and structure developed by the International Organization for Standardization, a description is given on the types of ecolabels that build on life cycle assessments. Focus is on type I labels that point out products and services with an overall environmental preferability...... of labelling, the use of ecolabels in marketing, and the way ecolabels help build a market for “greener products”. Type III labels—or Environmental Product Declarations—are also briefly described with indicative examples from the building sector, a declaration for office furniture, and an introduction is given...... to the European Commission’s programme for product—and organisational environmental footprints ....

  13. Semantic Role Labeling

    CERN Document Server

    Palmer, Martha; Xue, Nianwen

    2011-01-01

    This book is aimed at providing an overview of several aspects of semantic role labeling. Chapter 1 begins with linguistic background on the definition of semantic roles and the controversies surrounding them. Chapter 2 describes how the theories have led to structured lexicons such as FrameNet, VerbNet and the PropBank Frame Files that in turn provide the basis for large scale semantic annotation of corpora. This data has facilitated the development of automatic semantic role labeling systems based on supervised machine learning techniques. Chapter 3 presents the general principles of applyin

  14. FAITH – Fast Assembly Inhibitor Test for HIV

    Energy Technology Data Exchange (ETDEWEB)

    Hadravová, Romana [Institute of Organic Chemistry and Biochemistry IOCB Research Centre & Gilead Sciences, Academy of Sciences of the Czech Republic, Flemingovo nám. 2, 166 10 Prague (Czech Republic); Rumlová, Michaela, E-mail: michaela.rumlova@vscht.cz [Institute of Organic Chemistry and Biochemistry IOCB Research Centre & Gilead Sciences, Academy of Sciences of the Czech Republic, Flemingovo nám. 2, 166 10 Prague (Czech Republic); Department of Biotechnology, University of Chemistry and Technology, Prague, Technická 5, 166 28 Prague (Czech Republic); Ruml, Tomáš, E-mail: tomas.ruml@vscht.cz [Department of Biochemistry and Microbiology, University of Chemistry and Technology, Prague, Technická 3, 166 28 Prague (Czech Republic)

    2015-12-15

    Due to the high number of drug-resistant HIV-1 mutants generated by highly active antiretroviral therapy (HAART), there is continuing demand for new types of inhibitors. Both the assembly of the Gag polyprotein into immature and mature HIV-1 particles are attractive candidates for the blocking of the retroviral life cycle. Currently, no therapeutically-used assembly inhibitor is available. One possible explanation is the lack of a reliable and simple assembly inhibitor screening method. To identify compounds potentially inhibiting the formation of both types of HIV-1 particles, we developed a new fluorescent high-throughput screening assay. This assay is based on the quantification of the assembly efficiency in vitro in a 96-well plate format. The key components of the assay are HIV-1 Gag-derived proteins and a dual-labelled oligonucleotide, which emits fluorescence only when the assembly of retroviral particles is inhibited. The method was validated using three (CAI, BM2, PF74) reported assembly inhibitors. - Highlights: • Allows screening of assembly inhibitors of both mature and immature HIV-1 particles. • Based on Gag-derived proteins with CA in mature or immature conformation. • Simple and sensitive method suitable for high-throughput screening of inhibitors. • Unlike in other HIV assembly methods, works under physiological conditions. • No washing steps are necessary.

  15. Nuclear fuel assembly repair

    International Nuclear Information System (INIS)

    Bassler, E.A.; Stavsky, R.

    1986-01-01

    In response to utility needs to recover investment in nuclear fuel assemblies, Westinghouse Electric Corporation has developed tools and equipment to repair damaged fuel assemblies in an economical and safe manner, to enable utilities to reinsert these assemblies in the core. There are two possible repair techniques - bottom nozzle reconstitution and top nozzle reconstitution. Both techniques have been approved through formal design review; prototype tools have been built and successfully tested. The tools are modular in nature, easily transportable, and designed to fit the spent fuel pool at a reactor site. (author)

  16. TPX assembly plan

    International Nuclear Information System (INIS)

    Knutson, D.

    1993-01-01

    The TPX machine will be assembled in the TFTR Test Cell at the Plasma Physics Laboratory, utilizing the existing TFTR machine foundation. Preparation of the area for assembly will begin after completion of the decontamination and decommissioning phase on TFTR and certification that the radiation levels remaining, if any, are consistent with the types of operations planned. Assembly operations begin with the arrival of the first components, and conclude, approximately 24 months later, with the successful completion of the integrated systems tests and the achievement of a first plasma

  17. DC source assemblies

    Science.gov (United States)

    Campbell, Jeremy B; Newson, Steve

    2013-02-26

    Embodiments of DC source assemblies of power inverter systems of the type suitable for deployment in a vehicle having an electrically grounded chassis are provided. An embodiment of a DC source assembly comprises a housing, a DC source disposed within the housing, a first terminal, and a second terminal. The DC source also comprises a first capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the first terminal. The DC source assembly further comprises a second capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the second terminal.

  18. Succesful labelling schemes

    DEFF Research Database (Denmark)

    Juhl, Hans Jørn; Stacey, Julia

    2001-01-01

    to carry out a campaign targeted at this segment. The awareness percentage is already 92 % and 67% of the respondents believe they know the meaning of the scheme. But it stands to reason to study whether the respondents actually know what the labelling scheme stands for or if they just think they do...

  19. Energy labels and standards

    International Nuclear Information System (INIS)

    Newman, J.

    2000-01-01

    Improving energy efficiency at the end-use level is increasingly important as Climate Change commitments force policy makers to look for areas where greenhouse gas emissions reduction can be achieved rapidly. Indeed, although much improvement has been mode over the past 25 years, significant potential for improving energy efficiency still exists. Labelling and minimum efficiency standards for appliances and equipment have proven to be one of the most promising policy instruments. Used for many years in some IEA Member countries, they delivered tangible results. They are among the cheapest and least intrusive of policies. Policy makers cannot afford to neglect them. This book examines current and post experiences of countries using labels and standards to improve energy end-use efficiency. It identifies successful policy approaches, focusing on what works best. It also provides insight into the opportunities ahead, including the widespread use of computer chips in appliances, cars and equipment. This book should be of great help not only to administrations planning to introduce labelling schemes, but also to those in the process of strengthening their current programmes. Policy makers in developing countries will also find here all necessary justification for implementing labelling and standards in their economy. 74 refs

  20. Multi-label

    Directory of Open Access Journals (Sweden)

    Neda Abdelhamid

    2015-01-01

    Full Text Available Generating multi-label rules in associative classification (AC from single label data sets is considered a challenging task making the number of existing algorithms for this task rare. Current AC algorithms produce only the largest frequency class connected with a rule in the training data set and discard all other classes even though these classes have data representation with the rule’s body. In this paper, we deal with the above problem by proposing an AC algorithm called Enhanced Multi-label Classifiers based Associative Classification (eMCAC. This algorithm discovers rules associated with a set of classes from single label data that other current AC algorithms are unable to induce. Furthermore, eMCAC minimises the number of extracted rules using a classifier building method. The proposed algorithm has been tested on a real world application data set related to website phishing and the results reveal that eMCAC’s accuracy is highly competitive if contrasted with other known AC and classic classification algorithms in data mining. Lastly, the experimental results show that our algorithm is able to derive new rules from the phishing data sets that end-users can exploit in decision making.

  1. Labeling of herbicide femesafen

    International Nuclear Information System (INIS)

    She Dongmei; Qu Zhe; Tang Zhichang

    2004-01-01

    5-[2-chroo-4-(trifluoromethyl ) phenoxy]-N-(methyl sulphonyl )-2-niorobenzamide [femesafen] was labeled by six steps. Radio-chemical yield was 19.15%. TLC analysis of the final product showed that the radiochemical purity is not less than 99%. (authors)

  2. Competing Environmental Labels

    NARCIS (Netherlands)

    Fischer, Carolyn; Lyon, Thomas P.

    2014-01-01

    We study markets in which consumers prefer green products but cannot determine the environmental quality of any given firm's product on their own. A nongovernmental organization (NGO) can establish a voluntary standard and label products that comply with it. Alternatively, industry can create its

  3. Labeling of Cosmetic Products

    Directory of Open Access Journals (Sweden)

    Nicola Lionetti

    2018-03-01

    Full Text Available The labeling of cosmetic products provides a set of obligations, as reported in the Regulation 1223/2009, which came into force in Europe in July 2013. The indications reported on the label are intended to enable the clear identification of the functionality and proper use of cosmetics, ensure the protection of the consumer from the commercial aspects and, above all, from the safety point of view. Moreover, it should allow quick tracing of the product details and all info of toxicological relevance. However, the misuse of this tool often leads, on one side, to confusion among cosmetics, pharmaceuticals, medical devices, and biocides. On the other side, it gives rise to fanciful interpretations by a huge number of web users, who pretend to be able to judge the quality of a cosmetic product just by reading the ingredients list. This article points out the concrete purpose of cosmetic labels, in order to shed light on the use of certain categories of ‘controversial’ ingredients and on the real quality concepts of cosmetic products. Indeed, when properly interpreted, cosmetic labels represent a good tool for the professional investigation of adverse reactions to cosmetics.

  4. DNA-Based Self-Assembly of Fluorescent Nanodiamonds.

    Science.gov (United States)

    Zhang, Tao; Neumann, Andre; Lindlau, Jessica; Wu, Yuzhou; Pramanik, Goutam; Naydenov, Boris; Jelezko, Fedor; Schüder, Florian; Huber, Sebastian; Huber, Marinus; Stehr, Florian; Högele, Alexander; Weil, Tanja; Liedl, Tim

    2015-08-12

    As a step toward deterministic and scalable assembly of ordered spin arrays we here demonstrate a bottom-up approach to position fluorescent nanodiamonds (NDs) with nanometer precision on DNA origami structures. We have realized a reliable and broadly applicable surface modification strategy that results in DNA-functionalized and perfectly dispersed NDs that were then self-assembled in predefined geometries. With optical studies we show that the fluorescence properties of the nitrogen-vacancy color centers in NDs are preserved during surface modification and DNA assembly. As this method allows the nanoscale arrangement of fluorescent NDs together with other optically active components in complex geometries, applications based on self-assembled spin lattices or plasmon-enhanced spin sensors as well as improved fluorescent labeling for bioimaging could be envisioned.

  5. Nuclear reactor spacer assembly

    International Nuclear Information System (INIS)

    Anthony, A.J.; Groves, M.D.

    1979-01-01

    A fuel assembly for a nuclear reactor is disclosed wherein the fuel element receiving and supporting grid is comprised of a first metal, the guide tubes which pass through the grid assembly are comprised of a second metal and the grid is supported on the guide tubes by means of expanded sleeves located intermediate the grid and guide tubes. The fuel assembly is fabricated by inserting the sleeves, of initial outer diameter commensurate with the guide tube outer diameters, through the holes in the grid assembly provided for the guide tubes and thereafter expanding the sleeves radially outwardly along their entire length such that the guide tubes can subsequently be passed through the sleeves. The step of radial expansion, as a result of windows provided in the sleeves having dimensions commensurate with the geometry of the grid, mechanically captures the grid and simultaneously preloads the sleeve against the grid whereby relative motion between the grid and guide tube will be precluded

  6. Automated Assembly Center (AAC)

    Science.gov (United States)

    Stauffer, Robert J.

    1993-01-01

    The objectives of this project are as follows: to integrate advanced assembly and assembly support technology under a comprehensive architecture; to implement automated assembly technologies in the production of high-visibility DOD weapon systems; and to document the improved cost, quality, and lead time. This will enhance the production of DOD weapon systems by utilizing the latest commercially available technologies combined into a flexible system that will be able to readily incorporate new technologies as they emerge. Automated assembly encompasses the following areas: product data, process planning, information management policies and framework, three schema architecture, open systems communications, intelligent robots, flexible multi-ability end effectors, knowledge-based/expert systems, intelligent workstations, intelligent sensor systems, and PDES/PDDI data standards.

  7. Marine Acoustic Sensor Assembly

    National Research Council Canada - National Science Library

    Ruffa, Anthony A

    2007-01-01

    A marine acoustic sensor assembly includes an acoustic panel having a forward surface and an after surface, a laser scanner oriented so as to project a laser beam onto the acoustic panel after surface...

  8. Nuclear fuel assembly

    International Nuclear Information System (INIS)

    Anthony, A.J.

    1980-01-01

    A bimetallic spacer means is cooperatively associated with a nuclear fuel assembly and operative to resist the occurrence of in-reactor bowing of the nuclear fuel assembly. The bimetallic spacer means in one embodiment of the invention includes a space grid formed, at least principally, of zircaloy to the external surface of which are attached a plurality of stainless steel strips. In another embodiment the strips are attached to fuel pins. In each of the embodiments, the stainless steel strips during power production expand outwardly to a greater extent than do the members to which the stainless steel strips are attached, thereby forming stiff springs which abut against like bimetallic spacer means with which the other nuclear fuel assemblies are provided in a given nuclear reactor core to thus prevent the occurrence of in-reactor bowing of the nuclear fuel assemblies. (author)

  9. Mesoscale Polymer Assemblies

    Science.gov (United States)

    Choudhary, Satyan; Pham, Jonathan; Crosby, Alfred

    2015-03-01

    Materials encompassing structural hierarchy and multi-functionality allow for remarkable physical properties across different length scales. Mesoscale Polymer (MSP) assemblies provide a critical link, from nanometer to centimeter scales, in the definition of such hierarchical structures. Recent focus has been on exploiting these MSP assemblies for optical, electronic, photonics and biological applications. We demonstrate a novel fabrication method for MSP assemblies. Current fabrication methods restrict the length scale and volume of such assemblies. A new method developed uses a simple piezo-actuated motion for de-pinning of a polymer solution trapped by capillary forces between a flexible blade and a rigid substrate. The advantages of new method include ability to make MSP of monodisperse length and to fabricate sufficient volumes of MSP to study their physical properties and functionality in liquid dispersions. We demonstrate the application of MSP as filler for soft materials, providing rheological studies of the MSP with surrounding matrices.

  10. Federal Assembly, Prague

    Czech Academy of Sciences Publication Activity Database

    Hnídková, Vendula

    -, č. 37 (2011), s. 70 ISSN 1573-3815 Institutional research plan: CEZ:AV0Z80330511 Keywords : Czech architecture of the 20th century * Karel Prager * federal assembly Subject RIV: AL - Art, Architecture , Cultural Heritage

  11. Nuclear fuel assembly

    International Nuclear Information System (INIS)

    Betten, P.R.

    1976-01-01

    Under the invention the fuel assembly is particularly suitable for liquid metal cooled fast neutron breeder reactors. Hence, according to the invention a fuel assembly cladding includes inward corrugations with respect to the remainder of the cladding according to a recurring pattern determined by the pitch of the metal wire helically wound round the fuel rods of the assembly. The parts of the cladding pressed inwards correspond to the areas in which the wire encircling the peripheral fuel rods is generally located apart from the cladding, thereby reducing the play between the cladding and the peripheral fuel rods situated in these areas. The reduction in the play in turn improves the coolant flow in the internal secondary channels of the fuel assembly to the detriment of the flow in the peripheral secondary channels and thereby establishes a better coolant fluid temperature profile [fr

  12. Assembling Sustainable Territories

    DEFF Research Database (Denmark)

    Vandergeest, Peter; Ponte, Stefano; Bush, Simon

    2015-01-01

    The authors show how certification assembles ‘sustainable’ territories through a complex layering of regulatory authority in which both government and nongovernment entities claim rule-making authority, sometimes working together, sometimes in parallel, sometimes competitively. It is argued...

  13. VIRUS instrument collimator assembly

    Science.gov (United States)

    Marshall, Jennifer L.; DePoy, Darren L.; Prochaska, Travis; Allen, Richard D.; Williams, Patrick; Rheault, Jean-Philippe; Li, Ting; Nagasawa, Daniel Q.; Akers, Christopher; Baker, David; Boster, Emily; Campbell, Caitlin; Cook, Erika; Elder, Alison; Gary, Alex; Glover, Joseph; James, Michael; Martin, Emily; Meador, Will; Mondrik, Nicholas; Rodriguez-Patino, Marisela; Villanueva, Steven; Hill, Gary J.; Tuttle, Sarah; Vattiat, Brian; Lee, Hanshin; Chonis, Taylor S.; Dalton, Gavin B.; Tacon, Mike

    2014-07-01

    The Visual Integral-Field Replicable Unit Spectrograph (VIRUS) instrument is a baseline array 150 identical fiber fed optical spectrographs designed to support observations for the Hobby-Eberly Telescope Dark Energy Experiment (HETDEX). The collimator subassemblies of the instrument have been assembled in a production line and are now complete. Here we review the design choices and assembly practices used to produce a suite of identical low-cost spectrographs in a timely fashion using primarily unskilled labor.

  14. Nuclear fuel assembly

    International Nuclear Information System (INIS)

    Helmersson, S.

    1982-05-01

    The fuel assembly has a square-shaped cross section and it is put together of four quadratic assemblies each having seventeen positions for fuel rods, which are situated in a lattice formed by a pattern of triangles and squares. Nine of the positions correspond to the junction of a square lattice which has four squares, whereas eight rods are outside the quadratic past. (G.B.)

  15. Fuel assembly reconstitution

    International Nuclear Information System (INIS)

    Morgado, Mario M.; Oliveira, Monica G.N.; Ferreira Junior, Decio B.M.; Santos, Barbara O. dos; Santos, Jorge E. dos

    2009-01-01

    Fuel failures have been happened in Nuclear Power Plants worldwide, without lost of integrity and safety, mainly for the public, environment and power plants workers. The most common causes of these events are corrosion (CRUD), fretting and pellet cladding interaction. These failures are identified by increasing the activity of fission products, verified by chemical analyses of reactor coolant. Through these analyses, during the fourth operation cycle of Angra 2 Nuclear Power Plant, was possible to observe fuel failure indication. This indication was confirmed in the end of the cycle during the unloading of reactor core through leakage tests of fuel assembly, using the equipment called 'In Mast Sipping' and 'Box Sipping'. After confirmed, the fuel assembly reconstitution was scheduled, and happened in April, 2007, where was identified the cause and the fuel rod failure, which was substitute by dummy rods (zircaloy). The cause was fretting by 'debris'. The actions to avoid and prevent fuel assemblies failures are important. The goals of this work are to describe the methodology of fuel assembly reconstitution using the FARE (Fuel Assembly Reconstitution Equipment) system, to describe the results of this task in economic and security factors of the company and show how the fuel assembly failures are identified during operation and during the outage. (author)

  16. Polymer Directed Protein Assemblies

    Directory of Open Access Journals (Sweden)

    Patrick van Rijn

    2013-05-01

    Full Text Available Protein aggregation and protein self-assembly is an important occurrence in natural systems, and is in some form or other dictated by biopolymers. Very obvious influences of biopolymers on protein assemblies are, e.g., virus particles. Viruses are a multi-protein assembly of which the morphology is dictated by poly-nucleotides namely RNA or DNA. This “biopolymer” directs the proteins and imposes limitations on the structure like the length or diameter of the particle. Not only do these bionanoparticles use polymer-directed self-assembly, also processes like amyloid formation are in a way a result of directed protein assembly by partial unfolded/misfolded biopolymers namely, polypeptides. The combination of proteins and synthetic polymers, inspired by the natural processes, are therefore regarded as a highly promising area of research. Directed protein assembly is versatile with respect to the possible interactions which brings together the protein and polymer, e.g., electrostatic, v.d. Waals forces or covalent conjugation, and possible combinations are numerous due to the large amounts of different polymers and proteins available. The protein-polymer interacting behavior and overall morphology is envisioned to aid in clarifying protein-protein interactions and are thought to entail some interesting new functions and properties which will ultimately lead to novel bio-hybrid materials.

  17. Spin labels. Applications in biology

    International Nuclear Information System (INIS)

    Frangopol, T.P.; Frangopol, M.; Ionescu, S.M.; Pop, I.V.; Benga, G.

    1980-11-01

    The main applications of spin labels in the study of biomembranes, enzymes, nucleic acids, in pharmacology, spin immunoassay are reviewed along with the fundamentals of the spin label method. 137 references. (author)

  18. Human Assisted Assembly Processes

    Energy Technology Data Exchange (ETDEWEB)

    CALTON,TERRI L.; PETERS,RALPH R.

    2000-01-01

    Automatic assembly sequencing and visualization tools are valuable in determining the best assembly sequences, but without Human Factors and Figure Models (HFFMs) it is difficult to evaluate or visualize human interaction. In industry, accelerating technological advances and shorter market windows have forced companies to turn to an agile manufacturing paradigm. This trend has promoted computerized automation of product design and manufacturing processes, such as automated assembly planning. However, all automated assembly planning software tools assume that the individual components fly into their assembled configuration and generate what appear to be a perfectly valid operations, but in reality the operations cannot physically be carried out by a human. Similarly, human figure modeling algorithms may indicate that assembly operations are not feasible and consequently force design modifications; however, if they had the capability to quickly generate alternative assembly sequences, they might have identified a feasible solution. To solve this problem HFFMs must be integrated with automated assembly planning to allow engineers to verify that assembly operations are possible and to see ways to make the designs even better. Factories will very likely put humans and robots together in cooperative environments to meet the demands for customized products, for purposes including robotic and automated assembly. For robots to work harmoniously within an integrated environment with humans the robots must have cooperative operational skills. For example, in a human only environment, humans may tolerate collisions with one another if they did not cause much pain. This level of tolerance may or may not apply to robot-human environments. Humans expect that robots will be able to operate and navigate in their environments without collisions or interference. The ability to accomplish this is linked to the sensing capabilities available. Current work in the field of cooperative

  19. Labeling uncertainty in multitarget tracking

    NARCIS (Netherlands)

    Aoki, E.H.; Mandal, Pranab K.; Svensson, Lennart; Boers, Y.; Bagchi, Arunabha

    In multitarget tracking, the problem of track labeling (assigning labels to tracks) is an ongoing research topic. The existing literature, however, lacks an appropriate measure of uncertainty related to the assigned labels that has a sound mathematical basis as well as clear practical meaning to the

  20. A Development of the Lifting Tools for 40 .deg. Sector Sub-assembly and ITER Components

    International Nuclear Information System (INIS)

    Nam, Kyoungo; Park, Hyunki; Kim, Dongjin; Ahn, Heejae; Moon, Jaehwan; Emma, Watson; Shaw, Robert

    2013-01-01

    The lifting tools described in this paper are special tools used to lift and transfer the VV, TFC and pre-assembled 40 .deg sectors at sector sub-assembly tool placed in assembly building from the upending tool to the sector sub-assembly tool or to the Tokamak pit. The lifting tools consists of; the sector lifting tool, which is used universally for the major ITER components, and some lifting attachments for connecting components to the sector lifting tool to meet their lifting configurations. The functions, interfaces, features and configurations of the lifting tools are introduced as a result of their preliminary or final design. The results of the structural analysis to verify the stability of the lifting tools are described as well. The preliminary design of the lifting tools, including the sector lifting tool and associated lifting attachments, have been developed by KODA to satisfy the ITER assembly plan, procedure, environments, interfaces with associated tools or ITER components and technical requirements requested by IO. The structural stability of the lifting tools has been studied using ANSYS with an applied dead weight of the relevant components for example: VV, TFC and 40 .deg sector. For the heaviest load condition, the 40 .deg sector (about 1200 tons), a structural analysis has been carried out and these results are summarized in this paper. Based on the conceptual design proposed by the IO, the preliminary design of the sector lifting tool and associated lifting attachments have been developed to satisfy ITER assembly procedure, technical and functional requirements by KODA. Conclusions are summarized as following. Firstly, the sector lifting tool and associated lifting attachments have been developed by KODA to meet requirements of each lifting configuration for VV, TFC and VV/VVTS/TFC 40 .deg sector in their horizontal and vertical state. And for common use for the lifting of major components like VV and TFC, inboard and outboard cross beams were

  1. Learning with imperfectly labeled patterns

    Science.gov (United States)

    Chittineni, C. B.

    1979-01-01

    The problem of learning in pattern recognition using imperfectly labeled patterns is considered. The performance of the Bayes and nearest neighbor classifiers with imperfect labels is discussed using a probabilistic model for the mislabeling of the training patterns. Schemes for training the classifier using both parametric and non parametric techniques are presented. Methods for the correction of imperfect labels were developed. To gain an understanding of the learning process, expressions are derived for success probability as a function of training time for a one dimensional increment error correction classifier with imperfect labels. Feature selection with imperfectly labeled patterns is described.

  2. Photovoltaic self-assembly.

    Energy Technology Data Exchange (ETDEWEB)

    Lavin, Judith; Kemp, Richard Alan; Stewart, Constantine A.

    2010-10-01

    This late-start LDRD was focused on the application of chemical principles of self-assembly on the ordering and placement of photovoltaic cells in a module. The drive for this chemical-based self-assembly stems from the escalating prices in the 'pick-and-place' technology currently used in the MEMS industries as the size of chips decreases. The chemical self-assembly principles are well-known on a molecular scale in other material science systems but to date had not been applied to the assembly of cells in a photovoltaic array or module. We explored several types of chemical-based self-assembly techniques, including gold-thiol interactions, liquid polymer binding, and hydrophobic-hydrophilic interactions designed to array both Si and GaAs PV chips onto a substrate. Additional research was focused on the modification of PV cells in an effort to gain control over the facial directionality of the cells in a solvent-based environment. Despite being a small footprint research project worked on for only a short time, the technical results and scientific accomplishments were significant and could prove to be enabling technology in the disruptive advancement of the microelectronic photovoltaics industry.

  3. Map labeling and its generalizations

    Energy Technology Data Exchange (ETDEWEB)

    Doddi, S. [New Mexico Univ., Albuquerque, NM (United States). Dept. of Computer Science]|[Los Alamos National Lab., NM (United States); Marathe, M.V. [Los Alamos National Lab., NM (United States); Mirzaian, A. [York Univ., Toronto, ON (Canada). Dept. of Computer Science; Moret, B.M.E. [New Mexico Univ., Albuquerque, NM (United States). Dept. of Computer Science; Zhu, B. [City Univ. of Hong Kong (Hong Kong). Dept. of Computer Science]|[Los Alamos National Lab., NM (United States)

    1997-01-01

    Map labeling is of fundamental importance in cartography and geographical information systems and is one of the areas targeted for research by the ACM Computational Geometry Impact Task Force. Previous work on map labeling has focused on the problem of placing maximal uniform, axis-aligned, disjoint rectangles on the plane so that each point feature to be labeled lies at the corner of one rectangle. Here, we consider a number of variants of the map labeling problem. We obtain three general types of results. First, we devise constant-factor polynomial-time-approximation algorithms for labeling point features by rectangular labels, where the feature may lie anywhere on the boundary of its label region and where labeling rectangles may be placed in any orientation. These results generalize to the case of elliptical labels. Secondly, we consider the problem of labeling a map consisting of disjoint rectilinear fine segments. We obtain constant-factor polynomial-time approximation algorithms for the general problem and an optimal algorithm for the special case where all segments are horizontal. Finally, we formulate a bicriteria version of the map-labeling problem and provide bicriteria polynomial- time approximation schemes for a number of such problems.

  4. Linerless label device and method

    KAUST Repository

    Binladen, Abdulkari

    2016-01-14

    This apparatus and method for applying a linerless label to an end user product includes a device with a printer for printing on a face surface of a linerless label, and a release coat applicator for applying a release coat to the face surface of the label; another device including an unwinder unit (103) to unwind a roll of printed linerless label; a belt (108); a glue applicator (102) for applying glue to the belt; a nip roller (106) for contacting and applying pressure to the face surface of the linerless label such that the glue on the belt transfers to the back surface of the linerless label; at least one slitting knife 105) positioned downstream the belt and a rewinder unit (104) positioned downstream the slitting knife; and a third device which die cuts and applies the linerless label to an end user object.

  5. Community assembly of the worm gut microbiome

    Science.gov (United States)

    Gore, Jeff

    It has become increasingly clear that human health is strongly influenced by the bacteria that live within the gut, known collectively as the gut microbiome. This complex community varies tremendously between individuals, but understanding the sources that lead to this heterogeneity is challenging. To address this challenge, we are using a bottom-up approach to develop a predictive understanding of how the microbiome assembles and functions within a simple and experimentally tractable gut, the gut of the worm C. elegans. We have found that stochastic community assembly in the C. elegansintestine is sufficient to produce strong inter-worm heterogeneity in community composition. When worms are fed with two neutrally-competing fluorescently labeled bacterial strains, we observe stochastically-driven bimodality in community composition, where approximately half of the worms are dominated by each bacterial strain. A simple model incorporating stochastic colonization suggests that heterogeneity between worms is driven by the low rate at which bacteria successfully establish new intestinal colonies. We can increase this rate experimentally by feeding worms at high bacterial density; in these conditions the bimodality disappears. We have also characterized all pairwise interspecies competitions among a set of eleven bacterial species, illuminating the rules governing interspecies community assembly. These results demonstrate the potential importance of stochastic processes in bacterial community formation and suggest a role for C. elegans as a model system for ecology of host-associated communities.

  6. Magnetic nanoparticle assemblies

    CERN Document Server

    Trohidou, Kalliopi N

    2014-01-01

    Magnetic nanoparticles with diameters in the range of a few nanometers are today at the cutting edge of modern technology and innovation because of their use in numerous applications ranging from engineering to biomedicine. A great deal of scientific interest has been focused on the functionalization of magnetic nanoparticle assemblies. The understanding of interparticle interactions is necessary to clarify the physics of these assemblies and their use in the development of high-performance magnetic materials. This book reviews prominent research studies on the static and dynamic magnetic properties of nanoparticle assemblies, gathering together experimental and computational techniques in an effort to reveal their optimized magnetic properties for biomedical use and as ultra-high magnetic recording media.

  7. Integrated magnetic transformer assembly

    DEFF Research Database (Denmark)

    2014-01-01

    The present invention relates to an integrated magnetics transformer assembly comprising a first magnetically permeable core forming a first substantially closed magnetic flux path and a second magnetically permeable core forming a second substantially closed magnetic flux path. A first input...... inductor winding is wound around a first predetermined segment of the first magnetically permeable core and a second input inductor winding is wound around a first predetermined segment of the second magnetically permeable core. The integrated magnetics transformer assembly further comprises a first output......-winding of the first output inductor winding and the first half-winding of the second output inductor winding are configured to produce aligned, i.e. in the same direction, magnetic fluxes through the first substantially closed magnetic flux path. The integrated magnetics transformer assembly is well- suited for use...

  8. Reactor fuel assembly

    International Nuclear Information System (INIS)

    Anthony, A.J.; Groves, M.D.

    1980-01-01

    A nuclear reactor fuel assembly having a lower end fitting and actuating means interacting therewith for holding the assembly down on the core support stand against the upward flow of coolant. Locking means for interacting with projections on the support stand are carried by the lower end fitting and are actuated by the movement of an actuating rod operated from above the top of the assembly. In one embodiment of the invention the downward movement of the actuating rod forces a latched spring to move outward into locking engagement with a shoulder on the support stand projections. In another embodiment, the actuating rod is rotated to effect the locking between the end fitting and the projection. (author)

  9. Power module assembly

    Science.gov (United States)

    Campbell, Jeremy B [Torrance, CA; Newson, Steve [Redondo Beach, CA

    2011-11-15

    A power module assembly of the type suitable for deployment in a vehicular power inverter, wherein the power inverter has a grounded chassis, is provided. The power module assembly comprises a conductive base layer electrically coupled to the chassis, an insulating layer disposed on the conductive base layer, a first conductive node disposed on the insulating layer, a second conductive node disposed on the insulating layer, wherein the first and second conductive nodes are electrically isolated from each other. The power module assembly also comprises a first capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the first conductive node, and further comprises a second capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the second conductive node.

  10. Liaison based assembly design

    Energy Technology Data Exchange (ETDEWEB)

    Ames, A.; Kholwadwala, D.; Wilson, R.H.

    1996-12-01

    Liaison Based Assembly Design extends the current information infrastructure to support design in terms of kinematic relationships between parts, or liaisons. These liaisons capture information regarding contact, degrees-of-freedom constraints and containment relationships between parts in an assembly. The project involved defining a useful collection of liaison representations, investigating their properties, and providing for maximum use of the data in downstream applications. We tested our ideas by implementing a prototype system involving extensions to Pro/Engineer and the Archimedes assembly planner. With an expanded product model, the design system is more able to capture design intent. When a product update is attempted, increased knowledge availability improves our ability to understand the effect of design changes. Manufacturing and analysis disciplines benefit from having liaison information available, so less time is wasted arguing over incomplete design specifications and our enterprise can be more completely integrated.

  11. Transfer of fuel assemblies

    International Nuclear Information System (INIS)

    Vuckovich, M.; Burkett, J. P.; Sallustio, J.

    1984-01-01

    Fuel assemblies of a nuclear reactor are transferred during fueling or refueling or the like by a crane. The work-engaging fixture of the crane picks up an assembly, removes it from this slot, transfers it to the deposit site and deposits it in its slot at the deposit site. The control for the crane includes a strain gauge connected to the crane line which raises and lowers the load. The strain gauge senses the load on the crane. The signal from the strain gauge is compared with setpoints; a high-level setpoint, a low-level setpoint and a slack-line setpoint. If the strain gauge signal exceeds the high-level setpoint, the line drive is disabled. This event may occur during raising of a fuel assembly which encounters resistance. The high-level setpoint may be overridden under proper precautions. The line drive is also disabled if the strain gauge signal is less than the low-level setpoint. This event occurs when a fuel assembly being deposited contacts the bottom of its slot or an obstruction in, or at the entry to the slot. To preclude lateral movement and possible damage to a fuel assembly suspended from the crane line, the traverse drive of the crane is disabled once the strain-gauge exceets the lov-level setpoint. The traverse drive can only be enabled after the strain-gauge signal is less than the slack-line set-point. This occurs when the lines has been set in slack-line setting. When the line is tensioned after slack-li ne setting, the traverse drive remains enabled only if the line has been disconnected from the fuel assembly

  12. Neutron detector assembly

    International Nuclear Information System (INIS)

    Hanai, Koi; Shirayama, Shinpei.

    1978-01-01

    Purpose: To prevent gamma-ray from leaking externally passing through the inside of a neutron detector assembly. Constitution: In a neutron detector assembly having a protection pipe formed with an enlarged diameter portion which serves also as a spacer, partition plates with predetermined width are disposed at the upper and the lower portions in this expanded portion. A lot of metal particles are filled into spaces formed by the partition plates. In such a structure, the metal particles well-absorb the gamma-rays from above and convert them into heat to provide shielding for the gamma-rays. (Horiuchi, T.)

  13. Hand Controller Assembly

    Science.gov (United States)

    Bandera, Pablo (Inventor); Buchele, Paul (Inventor)

    2015-01-01

    A user input device for a vehicular electrical system is provided. The user input device includes a handle sized and shaped to be gripped by a human hand and a gimbal assembly within the handle. The gimbal assembly includes a first gimbal component, a second gimbal component coupled to the first gimbal component such that the second gimbal component is rotatable relative to the first gimbal component about a first axis, and a third gimbal component coupled to the second gimbal component such that the third gimbal component is rotatable relative to the second gimbal component about a second axis.

  14. Assembling an aesthetic.

    Science.gov (United States)

    Candela, Emily

    2012-12-01

    Recent research informing and related to the study of three-dimensional scientific models is assembled here in a way that explores an aesthetic, specifically, of touch. I concentrate on the materiality of models, drawing on insights from the history and philosophy of science, design and metaphysics. This article chronicles the ways in which touch, or material interactions, operate in the world of 3D models, and its role in what models mean and do. I end with a call for greater attention to scientific process, described as assembly of and within science, which is revealed by this focus on touch. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. Nuclear fuel assembly

    International Nuclear Information System (INIS)

    1975-01-01

    The nuclear fuel assembly described includes a cluster of fuel elements supported at a distance from each other so that their axes are parallel in order to establish secondary channels between them reserved for the coolant. Several ducts for an auxiliary cooling fluid are arranged in the cluster. The wall of each duct is pierced with coolant ejection holes which are placed circumferentially to a pre-determined pattern established according to the position of the duct in the cluster and by the axial distance of the ejection hole along the duct. This assembly is intended for reactors cooled by light or heavy water [fr

  16. Assembling RNA Nanoparticles.

    Science.gov (United States)

    Xiao, Shou-Jun

    2017-01-01

    RNA nanoparticles are designed and self-assembled according to noncanonical interactions of naturally conserved RNA motifs and/or canonical Watson-Crick base-pairing interactions, which have potential applications in gene therapy and nanomedicine. These artificially engineered nanoparticles are mainly synthesized from in vitro transcribed RNAs, purified by denaturing and native polyacrylamide gel electrophoresis (PAGE), and characterized with native PAGE, AFM, and TEM technologies. The protocols of in vitro transcription, denaturing and native PAGE, and RNA nanoparticle self-assembly are described in detail.

  17. Fire resistant PV shingle assembly

    Science.gov (United States)

    Lenox, Carl J.

    2012-10-02

    A fire resistant PV shingle assembly includes a PV assembly, including PV body, a fire shield and a connection member connecting the fire shield below the PV body, and a support and inter-engagement assembly. The support and inter-engagement assembly is mounted to the PV assembly and comprises a vertical support element, supporting the PV assembly above a support surface, an upper interlock element, positioned towards the upper PV edge, and a lower interlock element, positioned towards the lower PV edge. The upper interlock element of one PV shingle assembly is inter-engageable with the lower interlock element of an adjacent PV shingle assembly. In some embodiments the PV shingle assembly may comprise a ventilation path below the PV body. The PV body may be slidably mounted to the connection member to facilitate removal of the PV body.

  18. From Label to Practice

    DEFF Research Database (Denmark)

    Byrkjeflot, Haldor; Strandgaard, Jesper; Svejenova, Silviya

    2013-01-01

    This article examines the process of creation of new Nordic cuisine (NNC) as a culinary innovation, focusing on the main stages, actors, and mechanisms that shaped the new label and its practices and facilitated its diffusion in the region and internationally. Fast-paced diffusion was possible...... because NNC was conceived as an identity movement, triggered by active involvement of entrepreneurial leaders from the culinary profession, high-profile political supporters, legitimating scientists, disseminating media, and interpreting audiences. It was facilitated by three mechanisms: First, the use...

  19. Nanotechnology: A molecular assembler

    Science.gov (United States)

    Kelly, T. Ross; Snapper, Marc L.

    2017-09-01

    The idea of nanometre-scale machines that can assemble molecules has long been thought of as the stuff of science fiction. Such a machine has now been built -- and might herald a new model for organic synthesis. See Letter p.374

  20. Ordinary General Assembly

    CERN Multimedia

    Staff Association

    2011-01-01

    Tuesday 12 April at 14.00 Council Chamber, Bldg 503 In conformity with the Statutes of the Staff Association, an ordinary General Assembly is organized once a year (article IV.2.1). Agenda   Adoption of the Agenda Approval of the Draft Minutes of the Ordinary General Assembly of 20 April 2010 Presentation and approval of the Activity Report 2010 Presentation and approval of the Financial Report 2010 Presentation and approval of the Auditors Report 2010 Programme for 2011 Presentation et and approval of the draft budget and subscription rate 2012 Election of the Election Committee Election of the Board of Auditors Miscellaneous We remind members of article IV.3.4 in the Statutes of the Association which reads: “After having dealt with all the items on the agenda, the members may, with the consent of the Assembly, have other matters discussed, but decisions may be taken only on the items listed on the agenda. Nevertheless, the Assembly ma...

  1. Ordinary General Assembly

    CERN Multimedia

    Staff Association

    2011-01-01

    Tuesday 12 April at 14.00 Council Chamber, Bldg 503 In conformity with the Statutes of the Staff Association, an ordinary General Assembly is organized once a year (article IV.2.1). Agenda   Adoption of the Agenda Approval of the Draft Minutes of the Ordinary General Assembly of 20 April 2010 Presentation and approval of the Activity Report 2010 Presentation and approval of the Financial Report 2010 Presentation and approval of the Auditors Report 2010 Programme for 2011 Presentation and approval of the draft budget and subscription rate 2012 Election of the Election Committee Election of the Board of Auditors Miscellaneous We remind members of article IV.3.4 in the Statutes of the Association which reads: “After having dealt with all the items on the agenda, the members may, with the consent of the Assembly, have other matters discussed, but decisions may be taken only on the items listed on the agenda. Nevertheless, the Assembly may r...

  2. Ordinary General Assembly

    CERN Multimedia

    Staff Association

    2010-01-01

    Tuesday 20 April at 10.00 Council Chamber, Bldg 503 In conformity with the Statutes of the Staff Association, an ordinary General Assembly is organized once a year (article IV.2.1). Agenda   Adoption of the Agenda Approval of the Draft Minutes of the Ordinary General Assembly of 12 May 2009 Presentation and approval of the Activity Report 2009 Presentation and approval of the Financial Report 2009 Presentation and approval of the Auditors Report 2009 Programme for 2010 Presentation et and approval of the draft budget and subscription rate 2010 Election of the Election Committee Election of the Board of Auditors Miscellaneous We remind members of article IV.3.4 in the Statutes of the Association which reads: “After having dealt with all the items on the agenda, the members may, with the consent of the Assembly, have other matters discussed, but decisions may be taken only on the items listed on the agenda. Nevertheless, the Assembly may require t...

  3. America's Assembly Line

    DEFF Research Database (Denmark)

    Nye, David Edwin

    A social history of the assembly line, invented in 1913. Both praised as a boon to consumers and as a curse for workers, it has been satirized, imitated, and celebrated for 100 years. It has inspired fiction, comedy, cafeteria layouts, and suburban housing. It transformed industrial labor...

  4. Industrial Assembly Cases

    DEFF Research Database (Denmark)

    Ellekilde, Lars-Peter; Buch, Jacob Pørksen; Iversen, Thorbjørn Mosekjær

    This technical report presents 13 different industrial assembly tasks, which are composed of 70 different operations. The report is written to provide an overview and do as such not contain product specific information such as object weights, dimensions etc. The operations are classified into a set...

  5. Assembly of primary cilia

    DEFF Research Database (Denmark)

    Pedersen, Lotte B; Veland, Iben R; Schrøder, Jacob M

    2008-01-01

    knowledge about IFT is based on studies performed in Chlamydomonas and Caenorhabditis elegans. Therefore, our review of the IFT literature includes studies performed in these two model organisms. The role of several non-IFT proteins (e.g., centrosomal proteins) in the ciliary assembly process is also...... discussed. Developmental Dynamics, 2008. (c) 2008 Wiley-Liss, Inc....

  6. Spool assembly support analysis

    International Nuclear Information System (INIS)

    Norman, B.F.

    1994-01-01

    This document provides the wind/seismic analysis and evaluation for the pump pit spool assemblies. Hand calculations were used for the analysis. UBC, AISC, and load factors were used in this evaluation. The results show that the actual loads are under the allowable loads and all requirements are met

  7. Compression test assembly

    Science.gov (United States)

    Kariotis, A. H. (Inventor)

    1973-01-01

    A compression test assembly is described which prevents buckling of small diameter rigid specimens undergoing compression testing and permits attachment of extensometers for strain measurements. The test specimen is automatically aligned and laterally supported when compressive force is applied to the end caps and transmitted to the test specimen during testing.

  8. Nanoparticle assemblies and superstructures

    National Research Council Canada - National Science Library

    Kotov, Nicholas A

    2006-01-01

    ... building blocks of larger and more complex systems. Therefore, the present challenge of nanoscale science is to shift from making certain building blocks to organizing them in one-, two-, and three-dimensional structures. Such assemblies and superstructures are the next logical step in the development of nanoscience and nanotechnology. In this re...

  9. Macroscopic magnetic Self assembly

    NARCIS (Netherlands)

    Löthman, Per Arvid

    2018-01-01

    Exploring the macroscopic scale's similarities to the microscale is part and parcel of this thesis as reflected in the research question: what can we learn about the microscopic scale by studying the macroscale? Investigations of the environment in which the self-assembly takes place, and the

  10. Driving nucleolar assembly.

    Science.gov (United States)

    McCann, Kathleen L; Baserga, Susan J

    2014-02-01

    In this issue of Genes & Development, Grob and colleagues (pp. 220-230) identify the minimal molecular requirements to assemble a fully functional nucleolus in human cells and demonstrate the importance of the nucleolar transcription factor upstream binding factor (UBF) as a mitotic bookmark at the ribosomal DNA (rDNA).

  11. Assembling sustainable territories

    NARCIS (Netherlands)

    Vandergeest, Peter; Ponte, Stefano; Bush, Simon

    2015-01-01

    The authors show how certification assembles ‘sustainable’ territories through a complex layering of regulatory authority in which both government and nongovernment entities claim rule-making authority, sometimes working together, sometimes in parallel, sometimes competitively. It is argued that

  12. Characterization of assembled MEMS

    Science.gov (United States)

    Jandric, Zoran; Randall, John N.; Saini, Rahul; Nolan, Michael; Skidmore, George

    2005-01-01

    Zyvex is developing a low-cost high-precision method for manufacturing MEMS-based three-dimensional structures/assemblies. The assembly process relies on compliant properties of the interconnecting components. The sockets and connectors are designed to benefit from their compliant nature by allowing the mechanical component to self-align, i.e. reposition themselves to their designed, stable position, independent of the initial placement of the part by the external robot. Thus, the self-aligning property guarantees the precision of the assembled structure to be very close to, or the same, as the precision of the lithography process itself. A three-dimensional (3D) structure is achieved by inserting the connectors into the sockets through the use of a passive end-effector. We have developed the automated, high-yield, assembly procedure which permits connectors to be picked up from any location within the same die, or a separate die. This general procedure allows for the possibility to assemble parts of dissimilar materials. We have built many 3D MEMS structures, including several 3D MEMS devices such as a scanning electron microscope (SEM) micro column, mass-spectrometer column, variable optical attenuator. For these 3D MEMS structures we characterize their mechanical strength through finite element simulation, dynamic properties by finite-element analysis and experimentally with UMECH"s MEMS motion analyzer (MMA), alignment accuracy by using an in-house developed dihedral angle measurement laser autocollimator, and impact properties by performing drop tests. The details of the experimental set-ups, the measurement procedures, and the experimental data are presented in this paper.

  13. Probabilistic Performance Guarantees for Distributed Self-Assembly

    KAUST Repository

    Fox, Michael J.

    2015-04-01

    In distributed self-assembly, a multitude of agents seek to form copies of a particular structure, modeled here as a labeled graph. In the model, agents encounter each other in spontaneous pairwise interactions and decide whether or not to form or sever edges based on their two labels and a fixed set of local interaction rules described by a graph grammar. The objective is to converge on a graph with a maximum number of copies of a given target graph. Our main result is the introduction of a simple algorithm that achieves an asymptotically maximum yield in a probabilistic sense. Notably, agents do not need to update their labels except when forming or severing edges. This contrasts with certain existing approaches that exploit information propagating rules, effectively addressing the decision problem at the level of subgraphs as opposed to individual vertices. We are able to obey more stringent locality requirements while also providing smaller rule sets. The results can be improved upon if certain requirements on the labels are relaxed. We discuss limits of performance in self-assembly in terms of rule set characteristics and achievable maximum yield.

  14. A better carbon footprint label

    DEFF Research Database (Denmark)

    Thøgersen, John; Nielsen, Kristian S.

    2016-01-01

    Based on insights from behavioral economics, it is suggested to extend carbon footprint labeling with information about relative performance, using the well-known “traffic light” color scheme to communicate relative performance. To test this proposition, the impact of a carbon footprint label......, participants saw the original Carbon Trust label and in the other condition they saw the same label, but with traffic light colors added to communicate the product’s relative performance in terms of carbon footprint. All included attributes were found to have a significant impact on consumer choices...... to indicate relative carbon footprint significantly increases carbon label effectiveness. Hence, a carbon footprint label is more effective if it uses traffic light colors to communicate the product’s relative performance....

  15. Distance labeling schemes for trees

    DEFF Research Database (Denmark)

    Alstrup, Stephen; Gørtz, Inge Li; Bistrup Halvorsen, Esben

    2016-01-01

    We consider distance labeling schemes for trees: given a tree with n nodes, label the nodes with binary strings such that, given the labels of any two nodes, one can determine, by looking only at the labels, the distance in the tree between the two nodes. A lower bound by Gavoille et al. [Gavoille...... variants such as, for example, small distances in trees [Alstrup et al., SODA, 2003]. We improve the known upper and lower bounds of exact distance labeling by showing that 1/4 log2(n) bits are needed and that 1/2 log2(n) bits are sufficient. We also give (1 + ε)-stretch labeling schemes using Theta...

  16. Edge colouring by total labellings

    DEFF Research Database (Denmark)

    Brandt, Stephan; Rautenbach, D.; Stiebitz, M.

    2010-01-01

    We introduce the concept of an edge-colouring total k-labelling. This is a labelling of the vertices and the edges of a graph G with labels 1, 2, ..., k such that the weights of the edges define a proper edge colouring of G. Here the weight of an edge is the sum of its label and the labels of its...... two endvertices. We define χ (G) to be the smallest integer k for which G has an edge-colouring total k-labelling. This parameter has natural upper and lower bounds in terms of the maximum degree Δ of G : ⌈ (Δ + 1) / 2 ⌉ ≤ χ (G) ≤ Δ + 1. We improve the upper bound by 1 for every graph and prove χ (G...

  17. A Quantitative Proteomic Analysis of In Vitro Assembled Chromatin*

    Science.gov (United States)

    Völker-Albert, Moritz Carl; Pusch, Miriam Caroline; Fedisch, Andreas; Schilcher, Pierre; Schmidt, Andreas; Imhof, Axel

    2016-01-01

    The structure of chromatin is critical for many aspects of cellular physiology and is considered to be the primary medium to store epigenetic information. It is defined by the histone molecules that constitute the nucleosome, the positioning of the nucleosomes along the DNA and the non-histone proteins that associate with it. These factors help to establish and maintain a largely DNA sequence-independent but surprisingly stable structure. Chromatin is extensively disassembled and reassembled during DNA replication, repair, recombination or transcription in order to allow the necessary factors to gain access to their substrate. Despite such constant interference with chromatin structure, the epigenetic information is generally well maintained. Surprisingly, the mechanisms that coordinate chromatin assembly and ensure proper assembly are not particularly well understood. Here, we use label free quantitative mass spectrometry to describe the kinetics of in vitro assembled chromatin supported by an embryo extract prepared from preblastoderm Drosophila melanogaster embryos. The use of a data independent acquisition method for proteome wide quantitation allows a time resolved comparison of in vitro chromatin assembly. A comparison of our in vitro data with proteomic studies of replicative chromatin assembly in vivo reveals an extensive overlap showing that the in vitro system can be used for investigating the kinetics of chromatin assembly in a proteome-wide manner. PMID:26811354

  18. Labelled molecules, modern research implements

    International Nuclear Information System (INIS)

    Pichat, L.; Langourieux, Y.

    1974-01-01

    Details of the synthesis of carbon 14- and tritium-labelled molecules are examined. Although the methods used are those of classical organic chemistry the preparation of carbon 14-labelled molecules differs in some respects, most noticeably in the use of 14 CO 2 which requires very special handling techniques. For the tritium labelling of organic molecules the methods are somewhat different, very often involving exchange reactions. The following are described in turn: the so-called Wilzbach exchange method; exchange by catalysis in solution; catalytic hydrogenation with tritium; reductions with borotritides. Some applications of labelled molecules in organic chemistry, biochemistry and pharmacology are listed [fr

  19. New Ideas on Labeling Schemes

    DEFF Research Database (Denmark)

    Rotbart, Noy Galil

    in a distributed fashion increases. Second, attempting to answer queries on vertices of a graph stored in a distributed fashion can be significantly more complicated. In order to lay theoretical foundations to the first penalty mentioned a large body of work concentrated on labeling schemes. A labeling scheme...... evaluation of fully dynamic labeling schemes. Due to a connection between adjacency labeling schemes and the graph theoretical study of induced universal graphs, we study these in depth and show novel results for bounded degree graphs and power-law graphs. We also survey and make progress on the related...

  20. The radioactive labeling of monocytes

    International Nuclear Information System (INIS)

    Ensing, G.J.

    1985-01-01

    With the aim of studying a possible relationship between circulating monocytes and Sternberg-Reed cells investigations were started on the specific labeling of monocytes. In this thesis the literature on the pertinent data has been reviewed and a series of experiments on the monocyte labeling procedure has been described. The principles of cell labeling with radioactive compounds were discussed. 1. Total separation of the particular cell population to be labeled and subsequent labeling with a non-specific radiopharmaceutical. 2. Specific cell labeling in a mixture of cell types based on a well defined affinity of the cell under study for the radiopharmaceutical used. Next the radionuclides that can be used for cell labeling purposes were discussed with special attention for 111 In and its chelates. The principles of radiodosimetry were also discussed shortly. This section was focussed on the radiation dose the labeled cells receive because of the intracellular localized radioactivity. The radiation burden is high in comparison to amounts of radiation known to affect cell viability. A newly developed method for labeling monocytes specifically by phagocytosis of 111 In-Fe-colloid without apparent loss of cells was described in detail. (Auth.)

  1. Assembly and offset assignment scheme for self-similar traffic in optical burst switched networks

    CSIR Research Space (South Africa)

    Muwonge, KB

    2007-10-01

    Full Text Available Scheme for Self- similar Traffic in Optical Burst Switched Networks K. Benon Muwonge, Member, IEEE and H. Anthony Chan, Sr Member, IEEE Department of Electrical... Forward Equivalence Classification (FEC) assembly scheme to efficiently assemble self- similar traffic and a Pareto-offset assignment scheme for offset assignment. Two buffers, a packet buffer and a burst buffer, are implemented at the Label Edge...

  2. X-Ray Assembler Data

    Data.gov (United States)

    U.S. Department of Health & Human Services — Federal regulations require that an assembler who installs one or more certified components of a diagnostic x-ray system submit a report of assembly. This database...

  3. Assembling large, complex environmental metagenomes

    Energy Technology Data Exchange (ETDEWEB)

    Howe, A. C. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Plant Soil and Microbial Sciences; Jansson, J. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Earth Sciences Division; Malfatti, S. A. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Tringe, S. G. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Tiedje, J. M. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Plant Soil and Microbial Sciences; Brown, C. T. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Computer Science and Engineering

    2012-12-28

    The large volumes of sequencing data required to sample complex environments deeply pose new challenges to sequence analysis approaches. De novo metagenomic assembly effectively reduces the total amount of data to be analyzed but requires significant computational resources. We apply two pre-assembly filtering approaches, digital normalization and partitioning, to make large metagenome assemblies more computationaly tractable. Using a human gut mock community dataset, we demonstrate that these methods result in assemblies nearly identical to assemblies from unprocessed data. We then assemble two large soil metagenomes from matched Iowa corn and native prairie soils. The predicted functional content and phylogenetic origin of the assembled contigs indicate significant taxonomic differences despite similar function. The assembly strategies presented are generic and can be extended to any metagenome; full source code is freely available under a BSD license.

  4. Reflector-moderated critical assemblies

    International Nuclear Information System (INIS)

    Paxton, H.C.; Jarvis, G.A.; Byers, C.C.

    1975-07-01

    Experiments with reflector-moderated critical assemblies were part of the Rover Program at the Los Alamos Scientific Laboratory (LASL). These assemblies were characterized by thick D 2 O or beryllium reflectors surrounding large cavities that contained highly enriched uranium at low average densities. Because interest in this type of system has been revived by LASL Plasma Cavity Assembly studies, more detailed descriptions of the early assemblies than had been available in the unclassified literature are provided. (U.S.)

  5. Wellpoint assembly and method of installing a wellpoint assembly

    Energy Technology Data Exchange (ETDEWEB)

    Share, J.H.; Share, S.

    1988-12-13

    This patent describes a wellpoint assembly comprising in combination: an elongated flexible header pipe; coupling joints attached to the flexible header, each coupling joint being adapted for attaching a well point assembly; a flexible header pipe support for supporting the flexible header pipe; and means to align portions of a continuous flexible header pipe for attaching wellpoint assemblies, the means to align portions of the flexible header pipe including an alignment tool for aligning each flexible header coupling joint into a predetermined position for attaching a well point assembly line whereby a wellpoint assembly can be laid out around an excavation site in a wide variety of patterns.

  6. Oxygen labelled CO2

    International Nuclear Information System (INIS)

    Schuster, K.-D.; Heller, H.

    1989-01-01

    Tests were carried out as to whether additional information concerning pulmonary gas exchange could be obtained from the application of oxygen labelled carbon dioxide. Single breath experiments were performed on two healthy subjects with 0.1 percent C 16 O 18 O and 2.8 percent C 18 O 2 in the inspiratory gas. Breath-hold time was varied between 0.5-20s in different experiments. The 18 O-concentration of the end-expired gas bi-exponentially decreased with increasing breath-hold time. The high and low rate constants 4s -1 and 0.12s -1 for C 18 O 2 and 2.5s -1 and 0.87s -1 for C 16 O 18 O were derived, respectively. These results, together with model calculations, suggest: 1) the rapid disappearance of C 18 O 2 from the alveolar space is primarily limited by diffusion, so that this isotopic species can be applied to quantify pulmonary diffusing conditions; 2) the lower disappearance rate of C 16 O 18 O is caused by a lower equilibration kinetics in blood, so that this isotopic species offers a possibility to study carbonic anhydrase activity of the red cells in vivo; 3) the slow phase of label decay is influenced by both alveolar dead space and carbonic anhydrase activity of the pulmonary tissues. Pathological dead spaces are expected to be sensitively detectable by C 16 O 18 O as well as by C 18 O 2 . (author). 4 refs.; 4 figs

  7. FLUORINE CELL ANODE ASSEMBLY

    Science.gov (United States)

    Cable, R.E.; Goode, W.B. Jr.; Henderson, W.K.; Montillon, G.H.

    1962-06-26

    An improved anode assembly is deslgned for use in electrolytlc cells ln the productlon of hydrogen and fluorlne from a moIten electrolyte. The anode assembly comprises a copper post, a copper hanger supported by the post, a plurality of carbon anode members, and bolt means for clamplng half of the anode members to one slde of the hanger and for clamplng the other half of the anode members to the other slde of the hanger. The heads of the clamplng bolts are recessed withln the anode members and carbon plugs are inserted ln the recesses above the bolt heads to protect the boIts agalnst corroslon. A copper washer is provided under the head of each clamplng boIt such that the anode members can be tightly clamped to the hanger with a resultant low anode jolnt resistance. (AEC)

  8. Gamma counter shutter assembly

    International Nuclear Information System (INIS)

    Aday, R.W. Jr.; Barber, D.G.

    1976-01-01

    A shutter assembly for a radioactivity measuring apparatus is described having a sample counting chamber, the assembly having a bulky solid lead cylinder with a sample access port extending therethrough for alignment with the sample chamber. The cylinder is rotated by a Geneva wheel arrangement having a drive wheel with a plurality of equi-angularly disposed pins perpendicular to the surface thereof engaging radially extending open-ended slots in a driven wheel secured to the lead cylinder for concurrent rotation therewith. The drive wheel is rotated at a constant speed with the driven wheel accelerating as a pin traverses the slot from the open end toward the driven wheel center and then decelerating as the pin traverses the reverse direction to provide precise positioning with adjacent pins engaging the open ends of adjacent slots in the stop position of the cylinder. 8 Claims, 3 Drawing Figures

  9. Nuclear reactor fuel assembly

    International Nuclear Information System (INIS)

    1975-01-01

    A description is given of a nuclear reactor fuel assembly comprising a cluster of fuel elements supported by transversal grids so that their axes are parallel to and at a distance from each other, in order to establish interstices for the axial flow of a coolant. At least one of the interstices is occupied by an axial duct reserved for an auxiliary cooling fluid and is fitted with side holes through which the auxiliary cooling fluid is sprayed into the cluster. Deflectors extend as from a transversal grid in a position opposite the holes to deflect the cooling fluid jet towards those parts of the fuel elements that are not accessible to the auxiliary coolant. This assembly is intended for reactors cooled by light or heavy water [fr

  10. Nuclear fuel assembly

    International Nuclear Information System (INIS)

    Takeda, Tadashi; Sato, Kenji; Goto, Masakazu.

    1984-01-01

    Purpose: To facilitate identification of a fuel assembly upon fuel exchange in BWR type reactors. Constitution: Fluorescent material is coated or metal plating is applied to the impressed portion of a upper tie plate handle of a fuel assembly, and the fluorescent material or the metal plating surface is covered with a protective membrane made of transparent material. This enables to distinguish the impressed surface from a distant place and chemical reaction between the impressed surface and the reactor water can be prevented. Furthermore, since the protective membrane is formed such that it protrudes toward the upper side relative to the impressed surface, there is no risk of depositions of claddings thereover. (Moriyama, K.)

  11. Fuel nozzle assembly

    Science.gov (United States)

    Johnson, Thomas Edward [Greer, SC; Ziminsky, Willy Steve [Simpsonville, SC; Lacey, Benjamin Paul [Greer, SC; York, William David [Greer, SC; Stevenson, Christian Xavier [Inman, SC

    2011-08-30

    A fuel nozzle assembly is provided. The assembly includes an outer nozzle body having a first end and a second end and at least one inner nozzle tube having a first end and a second end. One of the nozzle body or nozzle tube includes a fuel plenum and a fuel passage extending therefrom, while the other of the nozzle body or nozzle tube includes a fuel injection hole slidably aligned with the fuel passage to form a fuel flow path therebetween at an interface between the body and the tube. The nozzle body and the nozzle tube are fixed against relative movement at the first ends of the nozzle body and nozzle tube, enabling the fuel flow path to close at the interface due to thermal growth after a flame enters the nozzle tube.

  12. Turbine seal assembly

    Science.gov (United States)

    Little, David A.

    2013-04-16

    A seal assembly that limits gas leakage from a hot gas path to one or more disc cavities in a turbine engine. The seal assembly includes a seal apparatus that limits gas leakage from the hot gas path to a respective one of the disc cavities. The seal apparatus comprises a plurality of blade members rotatable with a blade structure. The blade members are associated with the blade structure and extend toward adjacent stationary components. Each blade member includes a leading edge and a trailing edge, the leading edge of each blade member being located circumferentially in front of the blade member's corresponding trailing edge in a direction of rotation of the turbine rotor. The blade members are arranged such that a space having a component in a circumferential direction is defined between adjacent circumferentially spaced blade members.

  13. Mechanical Seal Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Kotlyar, Oleg M.

    1999-06-18

    An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transferring it to the mechanical diode.

  14. Solution deposition assembly

    Science.gov (United States)

    Roussillon, Yann; Scholz, Jeremy H; Shelton, Addison; Green, Geoff T; Utthachoo, Piyaphant

    2014-01-21

    Methods and devices are provided for improved deposition systems. In one embodiment of the present invention, a deposition system is provided for use with a solution and a substrate. The system comprises of a solution deposition apparatus; at least one heating chamber, at least one assembly for holding a solution over the substrate; and a substrate curling apparatus for curling at least one edge of the substrate to define a zone capable of containing a volume of the solution over the substrate. In another embodiment of the present invention, a deposition system for use with a substrate, the system comprising a solution deposition apparatus; at heating chamber; and at least assembly for holding solution over the substrate to allow for a depth of at least about 0.5 microns to 10 mm.

  15. Mechanical seal assembly

    Science.gov (United States)

    Kotlyar, Oleg M.

    2001-01-01

    An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transferring it to the mechanical diode.

  16. An Assembly Funnel Makes Biomolecular Complex Assembly Efficient

    Science.gov (United States)

    Zenk, John; Schulman, Rebecca

    2014-01-01

    Like protein folding and crystallization, the self-assembly of complexes is a fundamental form of biomolecular organization. While the number of methods for creating synthetic complexes is growing rapidly, most require empirical tuning of assembly conditions and/or produce low yields. We use coarse-grained simulations of the assembly kinetics of complexes to identify generic limitations on yields that arise because of the many simultaneous interactions allowed between the components and intermediates of a complex. Efficient assembly occurs when nucleation is fast and growth pathways are few, i.e. when there is an assembly “funnel”. For typical complexes, an assembly funnel occurs in a narrow window of conditions whose location is highly complex specific. However, by redesigning the components this window can be drastically broadened, so that complexes can form quickly across many conditions. The generality of this approach suggests assembly funnel design as a foundational strategy for robust biomolecular complex synthesis. PMID:25360818

  17. Ordinary General Assembly

    CERN Multimedia

    Association du personnel

    2010-01-01

    Tuesday 20 April at 10.00 Council Chamber, Bldg 503 In conformity with the Statutes of the Staff Association, an ordinary General Assembly is organized once a year (article IV.2.1). Agenda Adoption of the Agenda Approval of the Draft Minutes of the Ordinary General Assembly of 12 May 2009 Presentation and approval of the Activity Report 2009 Presentation and approval of the Financial Report 2009 Presentation and approval of the Auditors Report 2009 Programme for 2010 Presentation et and approval of the draft budget and subscription rate 2010 Modifications to the statutes of the association Election of the Election Committee Election of the Board of Auditors Miscellaneous We remind members of article IV.3.4 in the Statutes of the Association which reads: “After having dealt with all the items on the agenda, the members may, with the consent of the Assembly, have other matters discussed, but decisions may be taken only on the items listed on the agenda...

  18. SCT Barrel Assembly Complete

    CERN Multimedia

    L. Batchelor

    As reported in the April 2005 issue of the ATLAS eNews, the first of the four Semiconductor Tracker (SCT) barrels, complete with modules and services, arrived safely at CERN in January of 2005. In the months since January, the other three completed barrels arrived as well, and integration of the four barrels into the entire barrel assembly commenced at CERN, in the SR1 building on the ATLAS experimental site, in July. Assembly was completed on schedule in September, with the addition of the innermost layer to the 4-barrel assembly. Work is now underway to seal the barrel thermal enclosure. This is necessary in order to enclose the silicon tracker in a nitrogen atmosphere and provide it with faraday-cage protection, and is a delicate and complicated task: 352 silicon module powertapes, 352 readout-fibre bundles, and over 400 Detector Control System sensors must be carefully sealed into the thermal enclosure bulkhead. The team is currently verifying the integrity of the low mass cooling system, which must be d...

  19. IAHS Third Scientific Assembly

    Science.gov (United States)

    The International Association of Hydrological Sciences (IAHS) convened its Third Scientific Assembly in Baltimore, Md., May 10-19, 1989. The Assembly was attended by about 450 scientists and engineers. The attendance was highest from the U.S., as could be expected; 37 were from Canada; 22 each, Netherlands and United Kingdom; 14, Italy; 12, China; 10, Federal Republic of Germany; 8 each from France, the Republic of South Africa, and Switzerland; 7, Austria; 6 each, Finland and Japan; others were scattered among the remainder of 48 countries total.one of the cosponsors and also handled business matters for the Assembly. Other cosponsors included the International Association of Meteorology and Atmospheric Physics (IAMAP), United Nations Environmental Program (UNEP), United Nations Educational, Scientific, and Cultural Organization (UNESCO), World Meteorological Organization (WMO), and U.K. Overseas Development Authority (ODA). U.S. federal agencies serving as cosponsors included the Environmental Protection Agency, National Aeronautics and Space Administration, National Science Foundation, National Weather Service, Department of Agriculture, Department of State, and U.S. Geological Survey.

  20. Fourth Doctoral Student Assembly

    CERN Multimedia

    Ingrid Haug

    2016-01-01

    On 10 May, over 130 PhD students and their supervisors, from both CERN and partner universities, gathered for the 4th Doctoral Student Assembly in the Council Chamber.   The assembly was followed by a poster session, at which eighteen doctoral students presented the outcome of their scientific work. The CERN Doctoral Student Programme currently hosts just over 200 students in applied physics, engineering, computing and science communication/education. The programme has been in place since 1985. It enables students to do their research at CERN for a maximum of three years and to work on a PhD thesis, which they defend at their University. The programme is steered by the TSC committee, which holds two selection committees per year, in June and December. The Doctoral Student Assembly was opened by the Director-General, Fabiola Gianotti, who stressed the importance of the programme in the scientific environment at CERN, emphasising that there is no more rewarding activity than lear...

  1. Superselective pseudocontinuous arterial spin labeling

    NARCIS (Netherlands)

    Helle, M.; Norris, D.G.; Rufer, S.; Alfke, K.; Jansen, O.; van Osch, M.J.

    2010-01-01

    A new technique for the imaging of flow territories of individual extra- and intracranial arteries is presented. The method is based on balanced pseudocontinuous arterial spin labeling but employs additional time-varying gradients in between the radiofrequency pulses of the long labeling train. The

  2. 21 CFR 610.60 - Container label.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Container label. 610.60 Section 610.60 Food and... GENERAL BIOLOGICAL PRODUCTS STANDARDS Labeling Standards § 610.60 Container label. (a) Full label. The following items shall appear on the label affixed to each container of a product capable of bearing a full...

  3. Synthesis of 13C-labelled lactose for metabolic studies in subjects with gastrointestinal disorders

    International Nuclear Information System (INIS)

    Moyna, P.

    1993-01-01

    The long-range goals included development of a 13 C-labelled lactose method for measuring lactose malabsorption in patients with diarrhea. The short-term goals included assembling a nuclear magnetic resonance system and a computer system for spectra analysis. The latter results are the subject of the report. (author)

  4. A Better Carbon Footprint Label

    DEFF Research Database (Denmark)

    Thøgersen, John; Nielsen, Kristian S.

    2016-01-01

    Based on insights from behavioral economics, it is suggested to extend carbon footprint labeling with information about relative performance, using the well-known “traffic light” color scheme to communicate relative performance. To test this proposition, the impact of a carbon footprint label...... on Danish consumers' choice of ground coffee was tested in a 3 price levels × 3 levels of carbon emission × 3 certifying organizations × 2 organic labeling conditions discrete choice experiment. Participants were randomly assigned to two slightly different variants of the experiment: In one condition......, participants saw the original Carbon Trust label and in the other condition they saw the same label, but with traffic light colors added to communicate the product's relative performance in terms of carbon footprint. All included attributes were found to have a significant impact on consumer choices...

  5. Mass spectrometry–based relative quantification of proteins in precatalytic and catalytically active spliceosomes by metabolic labeling (SILAC), chemical labeling (iTRAQ), and label-free spectral count

    Science.gov (United States)

    Schmidt, Carla; Grønborg, Mads; Deckert, Jochen; Bessonov, Sergey; Conrad, Thomas; Lührmann, Reinhard; Urlaub, Henning

    2014-01-01

    The spliceosome undergoes major changes in protein and RNA composition during pre-mRNA splicing. Knowing the proteins—and their respective quantities—at each spliceosomal assembly stage is critical for understanding the molecular mechanisms and regulation of splicing. Here, we applied three independent mass spectrometry (MS)–based approaches for quantification of these proteins: (1) metabolic labeling by SILAC, (2) chemical labeling by iTRAQ, and (3) label-free spectral count for quantification of the protein composition of the human spliceosomal precatalytic B and catalytic C complexes. In total we were able to quantify 157 proteins by at least two of the three approaches. Our quantification shows that only a very small subset of spliceosomal proteins (the U5 and U2 Sm proteins, a subset of U5 snRNP-specific proteins, and the U2 snRNP-specific proteins U2A′ and U2B′′) remains unaltered upon transition from the B to the C complex. The MS-based quantification approaches classify the majority of proteins as dynamically associated specifically with the B or the C complex. In terms of experimental procedure and the methodical aspect of this work, we show that metabolically labeled spliceosomes are functionally active in terms of their assembly and splicing kinetics and can be utilized for quantitative studies. Moreover, we obtain consistent quantification results from all three methods, including the relatively straightforward and inexpensive label-free spectral count technique. PMID:24448447

  6. Acceleration of Amide Bond Rotation by Encapsulation in the Hydrophobic Interior of a Water-Soluble Supramolecular Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Pluth, Michael D.; Bergman, Robert G.; Raymond, Kenneth N.

    2008-04-08

    The hydrophobic interior cavity of a self-assembled supramolecular assembly exploits the hydrophobic effect for the encapsulation of tertiary amides. Variable temperature 1H NMR experiments reveal that the free energy barrier for rotation around the C-N amide bond is lowered by up to 3.6 kcal/mol upon encapsulation. The hydrophobic cavity of the assembly is able to stabilize the less polar transition state of the amide rotation process. Carbon-13 labeling studies showed that the {sup 13}C NMR carbonyl resonance increases with temperature for the encapsulated amides which suggests that the assembly is able to favor a twisted for of the amide.

  7. 40 CFR 86.007-35 - Labeling.

    Science.gov (United States)

    2010-07-01

    ... Methanol-Fueled Heavy-Duty Vehicles § 86.007-35 Labeling. Section 86.007-35 includes text that specifies... background of the label: (A) The label heading: Important Vehicle Information; (B) Full corporate name and...

  8. 40 CFR 86.095-35 - Labeling.

    Science.gov (United States)

    2010-07-01

    ... Methanol-Fueled Heavy-Duty Vehicles § 86.095-35 Labeling. (a) The manufacturer of any motor vehicle (or... color that contrasts with the background of the label: (A) The label heading: “Important Engine...

  9. Soil Fumigant Labels - Dimethyl Disulfide (DMDS)

    Science.gov (United States)

    Search by EPA registration number, product name, or company and follow the link to the Pesticide Product Labeling System (PPLS) for label details. Updated labels include new safety requirements for buffer zones and related measures.

  10. 40 CFR 94.212 - Labeling.

    Science.gov (United States)

    2010-07-01

    ... shall be of a color that contrasts with the background of the label: (1) The label heading: Marine...) to be designated as Blue Sky Series engines must contain the statement on the label: “Blue Sky Series...

  11. Mobile Application for Pesticide Label Matching

    Science.gov (United States)

    The label matching application will give inspectors the ability to instantly compare pesticide product labels against state and federal label databases via their cell phone, tablet or other mobile device.

  12. 21 CFR 1302.04 - Location and size of symbol on label and labeling.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Location and size of symbol on label and labeling... AND PACKAGING REQUIREMENTS FOR CONTROLLED SUBSTANCES § 1302.04 Location and size of symbol on label and labeling. The symbol shall be prominently located on the label or the labeling of the commercial...

  13. Nuclear reactor core assembly

    International Nuclear Information System (INIS)

    Baxi, C.B.

    1978-01-01

    The object of the present invention is to provide a fast reactor core assembly design for use with a fluid coolant such as liquid sodium or carbon monoxide incorporating a method of increasing the percentage of coolant flow though the blanket elements relative to the total coolant flow through the blanket and fuel elements during shutdown conditions without using moving parts. It is claimed that deterioration due to reactor radiation or temperature conditions is avoided and ready modification or replacement is possible. (U.K.)

  14. America's Assembly Line

    DEFF Research Database (Denmark)

    Nye, David Edwin

    A social history of the assembly line, invented in 1913. Both praised as a boon to consumers and as a curse for workers, it has been satirized, imitated, and celebrated for 100 years. It has inspired fiction, comedy, cafeteria layouts, and suburban housing. It transformed industrial labor...... and provoked strikes and union drives in the 1930s, but became a symbol of victory in the Second World War and Cold War. Reinvented by Japan as "lean production" and then increasingly automated after 1990, it remains a cornerstone of production but no longer employs many workers, even as it evolves toward...

  15. FORTRAN and ASSEMBLER programs

    International Nuclear Information System (INIS)

    Moldovan, N.

    1980-04-01

    A collection of programs written in FORTRAN and ASSEMBLER programming languages used in DOS-IBM is presented. The problems solved are of different sorts: linear programming, integration, matrix calculus, computation of absorbed doses in teletherapy, data sets (files) on magnetic tapes and disks, completion of DOS operating system etc. For reasons of space no details are given on the numerical methods or supplements and devices developed in order to achieve superior programs as to computation time and accuracy of result, although these might have been of use. All the programs in the collection have been checked up on an IBM 370/135 computer. (author)

  16. Regularized Label Relaxation Linear Regression.

    Science.gov (United States)

    Fang, Xiaozhao; Xu, Yong; Li, Xuelong; Lai, Zhihui; Wong, Wai Keung; Fang, Bingwu

    2018-04-01

    Linear regression (LR) and some of its variants have been widely used for classification problems. Most of these methods assume that during the learning phase, the training samples can be exactly transformed into a strict binary label matrix, which has too little freedom to fit the labels adequately. To address this problem, in this paper, we propose a novel regularized label relaxation LR method, which has the following notable characteristics. First, the proposed method relaxes the strict binary label matrix into a slack variable matrix by introducing a nonnegative label relaxation matrix into LR, which provides more freedom to fit the labels and simultaneously enlarges the margins between different classes as much as possible. Second, the proposed method constructs the class compactness graph based on manifold learning and uses it as the regularization item to avoid the problem of overfitting. The class compactness graph is used to ensure that the samples sharing the same labels can be kept close after they are transformed. Two different algorithms, which are, respectively, based on -norm and -norm loss functions are devised. These two algorithms have compact closed-form solutions in each iteration so that they are easily implemented. Extensive experiments show that these two algorithms outperform the state-of-the-art algorithms in terms of the classification accuracy and running time.

  17. PLC-γ1 Regulates Fibronectin Assembly and Cell Aggregation

    Science.gov (United States)

    Crooke, Cornelia E.; Pozzi, Ambra; Carpenter, Graham F.

    2009-01-01

    Phospholipase C-γ1 (PLC-γ1) mediates cell adhesion and migration through an undefined mechanism. Here, we examine the role of PLC-γ1 in cell-matrix adhesion in a hanging drop assay of cell aggregation. Plcg1 Null (−/−) mouse embryonic fibroblasts formed aggregates that were larger and significantly more resistant to dissociation than cells in which PLC-γ1 is re-expressed (Null + cells). Aggregate formation could be disrupted by inhibition of fibronectin interaction with integrins, indicating that fibronectin assembly may mediate aggregate formation. Fibronectin assembly was mediated by integrin α5β1 in both cell lines, while assays measuring fibronectin assembly revealed increased assembly in the Null cells. Null and Null + cells exhibited equivalent fibronectin mRNA levels and equivalent levels of fibronectin protein in pulse-labeling experiments. However, levels of secreted fibronectin in the conditioned medium were increased in Null cells. The data implicates a negative regulatory role for PLC-γ1 in cell aggregation by controlling the secretion of fibronectin into the media and its assembly into fibrils. PMID:19379731

  18. Neuronal assembly dynamics in supervised and unsupervised learning scenarios.

    Science.gov (United States)

    Moioli, Renan C; Husbands, Phil

    2013-11-01

    The dynamic formation of groups of neurons--neuronal assemblies--is believed to mediate cognitive phenomena at many levels, but their detailed operation and mechanisms of interaction are still to be uncovered. One hypothesis suggests that synchronized oscillations underpin their formation and functioning, with a focus on the temporal structure of neuronal signals. In this context, we investigate neuronal assembly dynamics in two complementary scenarios: the first, a supervised spike pattern classification task, in which noisy variations of a collection of spikes have to be correctly labeled; the second, an unsupervised, minimally cognitive evolutionary robotics tasks, in which an evolved agent has to cope with multiple, possibly conflicting, objectives. In both cases, the more traditional dynamical analysis of the system's variables is paired with information-theoretic techniques in order to get a broader picture of the ongoing interactions with and within the network. The neural network model is inspired by the Kuramoto model of coupled phase oscillators and allows one to fine-tune the network synchronization dynamics and assembly configuration. The experiments explore the computational power, redundancy, and generalization capability of neuronal circuits, demonstrating that performance depends nonlinearly on the number of assemblies and neurons in the network and showing that the framework can be exploited to generate minimally cognitive behaviors, with dynamic assembly formation accounting for varying degrees of stimuli modulation of the sensorimotor interactions.

  19. Interactive visualization for assembly planning

    Science.gov (United States)

    Chen, Jer-Sen; Bao, Guodi; Jiang, Jianli

    1995-04-01

    Assembly planning is an important component for automation in manufacturing. It can help reduce the production cost by avoiding unstable subassemblies and eliminating unnecessary tool changes within the assembly cell. The assembly plan generation process begins with the exploration of the precedence relations due to geometrical and mechanical constraints. After the precedence relations are derived, all feasible assembly sequences are generated. A diamond-shape graph is commonly used to visualize all possible assembly sequences. A dual representation of all assembly sequences is also provided to facilitate the assembly sequence comparison task. Each possible sequence is transformed into a nodal representation and assumes a spatial location in a three-dimensional space. The proximity among all assembly sequence nodes in the dual space is designed to reflect the similarity among the sequences. The user can therefore navigate in the space of all feasible assembly sequences and compare similar assembly sequences that are clustered closely in the dual space. All three visualizations, namely the precedence relation, the diamond graph, and the dual graph, are coupled together so that interactions on one visualization are reflected on the other two.

  20. On Constraints in Assembly Planning

    Energy Technology Data Exchange (ETDEWEB)

    Calton, T.L.; Jones, R.E.; Wilson, R.H.

    1998-12-17

    Constraints on assembly plans vary depending on product, assembly facility, assembly volume, and many other factors. Assembly costs and other measures to optimize vary just as widely. To be effective, computer-aided assembly planning systems must allow users to express the plan selection criteria that appIy to their products and production environments. We begin this article by surveying the types of user criteria, both constraints and quality measures, that have been accepted by assembly planning systems to date. The survey is organized along several dimensions, including strategic vs. tactical criteria; manufacturing requirements VS. requirements of the automated planning process itself and the information needed to assess compliance with each criterion. The latter strongly influences the efficiency of planning. We then focus on constraints. We describe a framework to support a wide variety of user constraints for intuitive and efficient assembly planning. Our framework expresses all constraints on a sequencing level, specifying orders and conditions on part mating operations in a number of ways. Constraints are implemented as simple procedures that either accept or reject assembly operations proposed by the planner. For efficiency, some constraints are supplemented with special-purpose modifications to the planner's algorithms. Fast replanning enables an interactive plan-view-constrain-replan cycle that aids in constraint discovery and documentation. We describe an implementation of the framework in a computer-aided assembly planning system and experiments applying the system to a number of complex assemblies, including one with 472 parts.

  1. New labels for radiation therapy

    International Nuclear Information System (INIS)

    Kubota, Susumu; Mukai, Minoru; Kato, Hirotoshi

    1992-01-01

    In simulating radiotherapy, the bone and trachea identified by plain X-P and the other organs, such as the esophagus and bladder, outlined by contrast medium have so far been used as labels. However, irradiation with a high therapeutic ratio is required for an intracorporeal insertion of artificial labels that are identified by X-ray fluoroscopy. For this purpose, metal clips and seed dummies are available, although they cause artifacts in CT scans. Therefore, the authors are using an acupuncture needle and lipiodol for tracing as new artificial labels, since both are identified by X-ray fluoroscopy and CT scan and create few artifacts. (J.P.N.)

  2. New labels for radiation therapy

    Energy Technology Data Exchange (ETDEWEB)

    Kubota, Susumu; Mukai, Minoru; Kato, Hirotoshi (National Inst. of Radiological Sciences, Chiba (Japan))

    1992-12-01

    In simulating radiotherapy, the bone and trachea identified by plain X-P and the other organs, such as the esophagus and bladder, outlined by contrast medium have so far been used as labels. However, irradiation with a high therapeutic ratio is required for an intracorporeal insertion of artificial labels that are identified by X-ray fluoroscopy. For this purpose, metal clips and seed dummies are available, although they cause artifacts in CT scans. Therefore, the authors are using an acupuncture needle and lipiodol for tracing as new artificial labels, since both are identified by X-ray fluoroscopy and CT scan and create few artifacts. (J.P.N.).

  3. Sustainability labels on food products

    DEFF Research Database (Denmark)

    Grunert, Klaus G; Hieke, Sophie; Wills, Josephine

    2014-01-01

    of sustainability was limited, but understanding of four selected labels (Fair Trade, Rainforest Alliance, Carbon Footprint, and Animal Welfare) was better, as some of them seem to be self-explanatory. The results indicated a low level of use, no matter whether use was measured as self-reported use of different......, human values as measured by the Schwartz value domains, and country differences. The results imply that sustainability labels currently do not play a major role in consumers’ food choices, and future use of these labels will depend on the extent to which consumers’ general concern about sustainability...

  4. Selenium-75-labelled foliate compounds

    International Nuclear Information System (INIS)

    1974-01-01

    A saturation method to analyze a foliate is presented; it uses competitive reaction of the compound to be measured and of a radioactive-labelled version of this compound with a reagent specific to this compound present in insufficient quantity to combine with the whole of the compound and its labelled version, separation of the bound compound from its non-bound homologue and measurement of the radioactivity concentration in the bound compound, the non-bound compound or both. The radioactive isotope used in the labelled foliate is selenium 75 [fr

  5. Bottom head assembly

    International Nuclear Information System (INIS)

    Fife, A.B.

    1998-01-01

    A bottom head dome assembly is described which includes, in one embodiment, a bottom head dome and a liner configured to be positioned proximate the bottom head dome. The bottom head dome has a plurality of openings extending there through. The liner also has a plurality of openings extending there through, and each liner opening aligns with a respective bottom head dome opening. A seal is formed, such as by welding, between the liner and the bottom head dome to resist entry of water between the liner and the bottom head dome at the edge of the liner. In the one embodiment, a plurality of stub tubes are secured to the liner. Each stub tube has a bore extending there through, and each stub tube bore is coaxially aligned with a respective liner opening. A seat portion is formed by each liner opening for receiving a portion of the respective stub tube. The assembly also includes a plurality of support shims positioned between the bottom head dome and the liner for supporting the liner. In one embodiment, each support shim includes a support stub having a bore there through, and each support stub bore aligns with a respective bottom head dome opening. 2 figs

  6. Control rod assemblies

    International Nuclear Information System (INIS)

    Yamanaka, Toshikatsu.

    1986-01-01

    Purpose: To obtain simple and practical control rod assemblies by bringing the exit temperature of the guide tube of a control rod main body closer to that of an adjacent fuel assembly and thereby suppressing the wasteful flow of coolants. Constitution: A flow control member comprises an annular flow control plate disposed above the control rod main body and bellows having a plurality of small paertures capable of passing coolants therethrough formed at the circumferencial surface. The bellows are to cause the flow control plate to resiliently abut on the upper surface of the control rod main body. Coolants flowing from below to above in the guide tube remove heat from the neutron absorbers and are discharged externally at an elevated temperature, while coolants at a lower temperature are entered and mixed through the apertures formed in the bellows. By the way, upon insertion of the control rod main body, flow of the coolants to the inside of the bellows is substantially interrupted by the extension contraction of the bellows, by which the flow rate is adjusted depending on the withdrawing stroke to suppress the occurrence of thermal problems. (Kamimura, M.)

  7. Progress of EMBarrel assembly

    CERN Multimedia

    Chalifour, M

    2002-01-01

    The assembly of the sixteen "M" modules into a vertical axis cylinder has been achieved last Friday, completing the first wheel of the Electromagnetic Barrel Calorimeter (see picture). With this, an important milestone in the construction of the ATLAS detector has been reached. Future steps are the rotation of the cylinder axis into horizontal position, in order to integrate the presamplers and heat exchangers by the end of October. The transportation of the wheel and its insertion into the cryostat is the next major milestone, and is planned for the beginning of 2003. The construction of the modules (the so-called "P" modules) of the second wheel is ongoing at Saclay, Annecy and CERN, and will be completed in the coming months. The assembly of the second wheel should start at CERN in February, and its insertion in the cryostat is scheduled for June 2003. This achievement is the result of a successful collaboration of all institutes involved in the construction of the EM Barrel, namely Annecy, Saclay and CE...

  8. ANNUAL GENERAL ASSEMBLY

    CERN Multimedia

    2001-01-01

    All members and beneficiaries of the Pension Fund are invited to attend the Annual General Asssembly to be held in the CERN Auditorium on Wednesday 3 October 2001 at 14.30 hrs The Agenda comprises:   Opening Remarks (P. Levaux) Some aspects of risk in a pension fund (C. Cuénoud) Annual Report 2000: Presentation and results (C. Cuénoud) Copies of the Report are available from divisional secretariats. Results of the actuarial reviews (G. Maurin) Questions from members and beneficiaries Persons wishing to ask questions are encouraged to submit them, where possible, in writing in advance, addressed to Mr C. Cuénoud, Administrator of the Fund. Conclusions (P. Levaux) As usual, participants are invited to drinks after the assembly. NB The minutes of the 2000 General Assembly are available from the Administration of the Fund (tel. + 41 22 767 91 94; e-mail Graziella.Praire@cern.ch) The English version will be published next week.

  9. Nuclear fuel assembly

    International Nuclear Information System (INIS)

    Hoshi, Masaya; Makihara, Yoshiaki.

    1985-01-01

    Purpose: To limit a bypass flow by inhibiting or restricting the lateral flow of coolants between lower nozzle legs of a nuclear fuel assembly, so that the flow speed of a jet stream flowing through the gaps between buffle plates into the reactor core is not increased. Constitution: The lower nozzle of a fuel assembly comprises an upper plate, an enclosure and legs, in which flow apertures are perforated in the enclosure, the area for the flow apertures and the slit are set to less than predetermined values, and the flow apertures are arranged so that they are situated within the gaps between the lower end of the buffle plate and the lower reactor core plate. As the result, since the jet stream from the gaps between the buffle plates can be so decreased as the effect thereof on the fuel rods is negligible, measurement for the size of the gap between the buffle plates upon periodical inspection is no more necessary, thereby enabling to shorten the time of the periodical inspection and reduce the exposure dose. (Kamimura, M.)

  10. International Space Station Assembly

    Science.gov (United States)

    1999-01-01

    The International Space Station (ISS) is an unparalleled international scientific and technological cooperative venture that will usher in a new era of human space exploration and research and provide benefits to people on Earth. On-Orbit assembly began on November 20, 1998, with the launch of the first ISS component, Zarya, on a Russian Proton rocket. The Space Shuttle followed on December 4, 1998, carrying the U.S.-built Unity cornecting Module. Sixteen nations are participating in the ISS program: the United States, Canada, Japan, Russia, Brazil, Belgium, Denmark, France, Germany, Italy, the Netherlands, Norway, Spain, Sweden, Switzerland, and the United Kingdom. The ISS will include six laboratories and be four times larger and more capable than any previous space station. The United States provides two laboratories (United States Laboratory and Centrifuge Accommodation Module) and a habitation module. There will be two Russian research modules, one Japanese laboratory, referred to as the Japanese Experiment Module (JEM), and one European Space Agency (ESA) laboratory called the Columbus Orbital Facility (COF). The station's internal volume will be roughly equivalent to the passenger cabin volume of two 747 jets. Over five years, a total of more than 40 space flights by at least three different vehicles - the Space Shuttle, the Russian Proton Rocket, and the Russian Soyuz rocket - will bring together more than 100 different station components and the ISS crew. Astronauts will perform many spacewalks and use new robotics and other technologies to assemble ISS components in space.

  11. NUTIRTION LABELLING OF FOOD AND ALLERGEN IN FOOD

    Directory of Open Access Journals (Sweden)

    Jozef Golian

    2012-10-01

    Full Text Available The new regulation introduced mandatory nutrition labelling and ordering food manufacturers provide information on energy and six nutrients: fat, saturated fatty acids, carbohydrates, sugars, protein and salt - in that order, and per 100 g or 100 ml. This information should be included in the nutritional table in one visual field (usually on the back cover, moreover, can also be expressed on per serving. It is important to realize that this regulation requires manufacturers indicate the nutritional value in one field of vision, usually on the "back cover" designation in the principal field (e.g. "on the front cover" remains voluntary. Food allergy is a significant public health issue worldwide. Regulatory risk management strategies for allergic consumers have focused on providing information about the presence of food allergens through label declarations. A number of countries and regulatory bodies have recognized the importance of providing this information by enacting laws, regulations or standards for food allergen labelling of ‘‘priority allergens. Increasing volume of the international food trade suggests that there would be value in supporting sensitive consumers by harmonizing (to the extent possible these regulatory frameworks. As a first step toward this goal, an inventory of allergen labelling regulations was assembled and analyzed to identify commonalities, differences, and future needs.doi:10.5219/230

  12. Selecting Operations for Assembler Encoding

    Directory of Open Access Journals (Sweden)

    Tomasz Praczyk

    2010-04-01

    Full Text Available Assembler Encoding is a neuro-evolutionary method in which a neural network is represented in the form of a simple program called Assembler Encoding Program. The task of the program is to create the so-called Network Definition Matrix which maintains all the information necessary to construct the network. To generate Assembler Encoding Programs and the subsequent neural networks evolutionary techniques are used.
    The performance of Assembler Encoding strongly depends on operations used in Assembler Encoding Programs. To select the most effective operations, experiments in the optimization and the predator-prey problem were carried out. In the experiments, Assembler Encoding Programs equipped with different types of operations were tested. The results of the tests are presented at the end of the paper.

  13. Method of assembling thermonuclear devices

    International Nuclear Information System (INIS)

    Kikuchi, Katsumasa; Ishizuka, Tatsuro.

    1985-01-01

    Purpose: To facilitate the assembling work and improve the reliability thereby obtain an economical advantage. Method: A substantially doughnut-like vacuum vessel containing plasmas and having an insulating dividing portions for dividing along the torus circumference direction is further disposed with dividing poritons with no insulation. Upon assembling, insulating dividing poritons are previously assembled to leave the not-insulated dividing portions as the final couplings while leaving such gaps as incorporating toroidal coils. Then, the toroidal coils are assembled through the gaps to the vacuum vessel and, finally not-insulated final dividing portions are assembled. Since the function is divided into the dividing portion applied with insulation for vacuum seal and dividing portions absorbing the dimensional errors for vacuum seal, assembling work in view of mechanical procedure and vacuum can be facilitated. (Sekiya, K.)

  14. New Labeling for Neonicotinoid Pesticides

    Science.gov (United States)

    These documents, a graphic of the bee advisory box and letters to pesticide registrants, describe steps by EPA to change pesticide labels to better protect pollinators by being clearer and more precise in their directions for pesticide application.

  15. Use the Nutrition Facts Label

    Science.gov (United States)

    ... Find A Program Near You Develop Your Program City and County Sites Case Studies National Partners National ... 20% DV or more is high Visit the Smart Food Shopping page and learn how the label ...

  16. Meat and Poultry Labeling Terms

    Science.gov (United States)

    ... Web Content Viewer (JSR 286) Actions ${title} Loading... Meat and Poultry Labeling Terms What does 'mechanically separated ... Top of Page ] NATURAL: A product containing no artificial ingredient or added color and is only minimally ...

  17. Canonical Labelling of Site Graphs

    Directory of Open Access Journals (Sweden)

    Nicolas Oury

    2013-06-01

    Full Text Available We investigate algorithms for canonical labelling of site graphs, i.e. graphs in which edges bind vertices on sites with locally unique names. We first show that the problem of canonical labelling of site graphs reduces to the problem of canonical labelling of graphs with edge colourings. We then present two canonical labelling algorithms based on edge enumeration, and a third based on an extension of Hopcroft's partition refinement algorithm. All run in quadratic worst case time individually. However, one of the edge enumeration algorithms runs in sub-quadratic time for graphs with "many" automorphisms, and the partition refinement algorithm runs in sub-quadratic time for graphs with "few" bisimulation equivalences. This suite of algorithms was chosen based on the expectation that graphs fall in one of those two categories. If that is the case, a combined algorithm runs in sub-quadratic worst case time. Whether this expectation is reasonable remains an interesting open problem.

  18. Quality control of labelled compounds

    International Nuclear Information System (INIS)

    Matucha, M.

    1979-01-01

    Some advantages and disadvantages of methods used for quality control of organic labelled compounds (1 31 I, 14 C) are shortly discussed. The methods used are electrophoresis, ultraviolet and infrared spectrometry, radiogas and thin-layer chromatography. (author)

  19. Integral nuclear fuel element assembly

    International Nuclear Information System (INIS)

    Schluderberg, D. C.

    1985-01-01

    An integral nuclear fuel element assembly utilizes longitudinally finned fuel pins. The continuous or interrupted fins of the fuel pins are brazed to fins of juxtaposed fuel pins or directly to the juxtaposed fuel pins or both. The integrally brazed fuel assembly is designed to satisfy the thermal and hydraulic requirements of a fuel assembly lattice having moderator to fuel atom ratios required to achieve high conversion and breeding ratios

  20. Gas separation membrane module assembly

    Science.gov (United States)

    Wynn, Nicholas P [Palo Alto, CA; Fulton, Donald A [Fairfield, CA

    2009-03-31

    A gas-separation membrane module assembly and a gas-separation process using the assembly. The assembly includes a set of tubes, each containing gas-separation membranes, arranged within a housing. The housing contains a tube sheet that divides the space within the housing into two gas-tight spaces. A permeate collection system within the housing gathers permeate gas from the tubes for discharge from the housing.

  1. Synthesis of Cryptophycin Affinity Labels and Tubulin Labeling

    Science.gov (United States)

    2006-05-01

    100 6.0 447 25.3 aTubulin at 1.5 mg/mL was assembled at 37 °C for 15 min in the presence of PEM buffer, 0.5 mM GTP...cryptophycin-24 (18a-c). They were tested in a tubulin assembly assay, and for their cytotoxicity against MCF7, and MCF7-ADR breast cancer cell lines. The

  2. Synthesis of isotopically labelled salicylates

    International Nuclear Information System (INIS)

    Hawkins, D.R.; Pryor, R.W.

    1981-01-01

    [ 13 C-carboxyl]Salicylic acid has been prepared by carbonation of 2-benzyloxybromobenzene followed by reductive debenzylation. Deuterium and tritium labelled salicylic acid and 2 H 2 / 13 C-salicylic acid were prepared by reduction of the 3,5-dibromo derivatives using Raney Ni-Al. Deuterium labelled salicylic acid containing up to four deuterium atoms was prepared by catalytic exchange with Raney Ni-Al in 5% NaOD/D 2 O. (author)

  3. Assembly of the PLT device

    International Nuclear Information System (INIS)

    Marino, R.

    1975-11-01

    The assembly of the PLT device began in June 1974 with a preassembly of the mechanical structure at a remote site. The preassembly sequence incorporated final fabrication procedures with an initial staging operation. This successful staging/fabrication procedure proved to be an invaluable asset when the final assembly was started in August 1974. The assembly continued with the initial reassembly of the previously tested structural components at the final machine site. Construction was interrupted at several points to allow for toroidal field coil, vacuum vessel, and poloidal coil installation. Two phases of toroidal field coil power tests were included in the assembly sequence prior to, and just after the vacuum vessel insertion

  4. Moisture Research - Optimizing Wall Assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Arena, Lois [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Mantha, Pallavi [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2013-05-01

    In this project, the Consortium for Advanced Residential Buildings (CARB) team evaluated several different configurations of wall assemblies to determine the accuracy of moisture modeling and make recommendations to ensure durable, efficient assemblies. WUFI and THERM were used to model the hygrothermal and heat transfer characteristics of these walls. Wall assemblies evaluated included code minimum walls using spray foam insulation and fiberglass batts, high R-value walls at least 12 in. thick (R-40 and R-60 assemblies), and brick walls with interior insulation.

  5. Seismic behaviour of fuel assembly

    Energy Technology Data Exchange (ETDEWEB)

    Song, Heuy Gap; Jhung, Myung Jo [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1993-11-01

    A general approach for the dynamic time-history analysis of the reactor core is presented in this paper as a part of the fuel assembly qualification program. Several detailed core models are set up to reflect the placement of the fuel assemblies within the core shroud. Peak horizontal responses are obtained for each model for the motions induced from earthquake. The dynamic responses such as fuel assembly shear force, bending moment and displacement, and spacer grid impact loads are carefully investigated. Also, the sensitivity responses are obtained for the earthquake motions and the fuel assembly non-linear response characteristics are discussed. (Author) 9 refs., 24 figs., 1 tab.

  6. Rocket Assembly and Checkout Facility

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Integrates, tests, and calibrates scientific instruments flown on sounding rocket payloads. The scientific instruments are assembled on an optical bench;...

  7. Next-generation transcriptome assembly

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Jeffrey A.; Wang, Zhong

    2011-09-01

    Transcriptomics studies often rely on partial reference transcriptomes that fail to capture the full catalog of transcripts and their variations. Recent advances in sequencing technologies and assembly algorithms have facilitated the reconstruction of the entire transcriptome by deep RNA sequencing (RNA-seq), even without a reference genome. However, transcriptome assembly from billions of RNA-seq reads, which are often very short, poses a significant informatics challenge. This Review summarizes the recent developments in transcriptome assembly approaches - reference-based, de novo and combined strategies-along with some perspectives on transcriptome assembly in the near future.

  8. Geometric reasoning about assembly tools

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, R.H.

    1997-01-01

    Planning for assembly requires reasoning about various tools used by humans, robots, or other automation to manipulate, attach, and test parts and subassemblies. This paper presents a general framework to represent and reason about geometric accessibility issues for a wide variety of such assembly tools. Central to the framework is a use volume encoding a minimum space that must be free in an assembly state to apply a given tool, and placement constraints on where that volume must be placed relative to the parts on which the tool acts. Determining whether a tool can be applied in a given assembly state is then reduced to an instance of the FINDPLACE problem. In addition, the author presents more efficient methods to integrate the framework into assembly planning. For tools that are applied either before or after their target parts are mated, one method pre-processes a single tool application for all possible states of assembly of a product in polynomial time, reducing all later state-tool queries to evaluations of a simple expression. For tools applied after their target parts are mated, a complementary method guarantees polynomial-time assembly planning. The author presents a wide variety of tools that can be described adequately using the approach, and surveys tool catalogs to determine coverage of standard tools. Finally, the author describes an implementation of the approach in an assembly planning system and experiments with a library of over one hundred manual and robotic tools and several complex assemblies.

  9. Self-assembly of self-assembled molecular triangles

    Indian Academy of Sciences (India)

    While the solution state structure of 1 can be best described as a trinuclear complex, in the solidstate well-fashioned intermolecular - and CH- interactions are observed. Thus, in the solid-state further self-assembly of already self-assembled molecular triangle is witnessed. The triangular panels are arranged in a linear ...

  10. Method and apparatus for assembling a permanent magnet pole assembly

    Science.gov (United States)

    Carl, Jr., Ralph James; Bagepalli, Bharat Sampathkumaran [Niskayuna, NY; Jansen, Patrick Lee [Scotia, NY; Dawson, Richard Nils [Voorheesville, NY; Qu, Ronghai [Clifton Park, NY; Avanesov, Mikhail Avramovich [Moscow, RU

    2009-08-11

    A pole assembly for a rotor, the pole assembly includes a permanent magnet pole including at least one permanent magnet block, a plurality of laminations including a pole cap mechanically coupled to the pole, and a plurality of laminations including a base plate mechanically coupled to the pole.

  11. Reconfigurable assembly work station

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Yhu-Tin; Abell, Jeffrey A.; Spicer, John Patrick

    2017-11-14

    A reconfigurable autonomous workstation includes a multi-faced superstructure including a horizontally-arranged frame section supported on a plurality of posts. The posts form a plurality of vertical faces arranged between adjacent pairs of the posts, the faces including first and second faces and a power distribution and position reference face. A controllable robotic arm suspends from the rectangular frame section, and a work table fixedly couples to the power distribution and position reference face. A plurality of conveyor tables are fixedly coupled to the work table including a first conveyor table through the first face and a second conveyor table through the second face. A vision system monitors the work table and each of the conveyor tables. A programmable controller monitors signal inputs from the vision system to identify and determine orientation of the component on the first conveyor table and control the robotic arm to execute an assembly task.

  12. Nuclear fuel assembly

    International Nuclear Information System (INIS)

    Domoto, Noboru; Masuda, Hiroyuki

    1989-01-01

    In a nuclear fuel assembly loaded with a plurality of fuel rods, the inside of a fuel rod disposed at a high neutron flux region is divided into an inner region and an outer region, and more burnable poisons are mixed in the inner region than in the outer region. Alternatively, the central portion of a pellet disposed in a high neutron flux region is made hollow, in which burnable poisons are charged. This can prevent neutron infinite multiplication factor from decreasing extremely at the initial burning stage. Further, the burnable poisons are not rapidly burnt completely and local peaking coefficient can be controlled. Accordingly, in a case of suppressing a predetermined excess reactivity by using a fuel rod incorporated with the burnable poison, the fuel economy can be improved more and the reactor core controllability can also be improved as compared with the usual case. (T.M.)

  13. Ultrasonic calibration assembly

    International Nuclear Information System (INIS)

    1981-01-01

    Ultrasonic transducers for in-service inspection of nuclear reactor vessels have several problems associated with them which this invention seeks to overcome. The first is that of calibration or referencing a zero start point for the vertical axis of transducer movement to locate a weld defect. The second is that of verifying the positioning (vertically or at a predetermined angle). Thirdly there is the problem of ascertaining the speed per unit distance in the operating medium of the transducer beam prior to the actual inspection. The apparatus described is a calibration assembly which includes a fixed, generally spherical body having a surface for reflecting an ultrasonic beam from one of the transducers which can be moved until the reflection from the spherical body is the highest amplitude return signal indicating radial alignment from the body. (U.K.)

  14. Reactor fuel assembly fastening

    International Nuclear Information System (INIS)

    Formanek, F.J.; Schukei, G.E.

    1980-01-01

    A nuclear fuel assembly is described, adapted to be locked into first mating surfaces on a core support stand, comprising a lower end fitting having posts for resting on the stand; elongated hook members pivotally connected at one end to the lower end fitting and having a second mating surface at the other end to engage the first mating surfaces; actuating means located between the posts on the lower end fitting and being vertically movable relative to the end fitting; and rigid links pivotally attached at one end to the hook members intermediate the connection of the hook members to the end fitting and the second mating surface and pivotally attached at the other end to the actuating means, the link having a length between the pivoted connections such that the second mating surface on the hook members locks into engagement with the first mating surfaces on the stand as the links approach the horizontal. (author)

  15. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Vision Facts and Myths How to Read a Nutrition Facts Label (Video) KidsHealth > For Parents > How to Read a Nutrition Facts Label (Video) Print A A A en ... nutricionales (video) Most packaged foods come with a Nutrition Facts label. These labels have a lot of ...

  16. Use of labeled compounds in tracer experiments

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    The use of radiotracers in research has become common. This chapter looks at some of the underlying assumptions and advantages of labeled compounds: advantages of radiotracers; availability of suitable tracers and labeled compounds; purity of labeled compounds; autoradiolysis; storage of labeled compounds; detection systems for chromatography and electrophoretic methods. 14 refs., 2 figs

  17. 78 FR 8362 - Energy Labeling Rule

    Science.gov (United States)

    2013-02-06

    ... the label's technical efficiency rating terms (e.g., SEER) should appear in a more prominent fashion... appearance of two different maps on the same label. For central air-conditioner models that do not meet the... proposed label placement requirements. For example, ACCA asserted that the label's appearance on packaging...

  18. 21 CFR 606.121 - Container label.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Container label. 606.121 Section 606.121 Food and... Container label. (a) The container label requirements are designed to facilitate the use of a uniform container label for blood and blood components (except Source Plasma) by all blood establishments. (b) The...

  19. 7 CFR 70.45 - Misleading labeling.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Misleading labeling. 70.45 Section 70.45 Agriculture... Misleading labeling. The use of the terms “Government Graded” and “Federal-State Graded” or terms of similar import in the labeling or advertising of any product without stating in the labeling or advertisement the...

  20. Induced self-assembly and Förster resonance energy transfer studies of alkynylplatinum(II) terpyridine complex through interaction with water-soluble poly(phenylene ethynylene sulfonate) and the proof-of-principle demonstration of this two-component ensemble for selective label-free detection of human serum albumin.

    Science.gov (United States)

    Chung, Clive Yik-Sham; Yam, Vivian Wing-Wah

    2011-11-23

    The interaction of conjugated polyelectrolyte, PPE-SO(3)(-), with platinum(II) complexes, [Pt(tpy)(C≡CC(6)H(4)-CH(2)NMe(3)-4)](OTf)(2) (1) and [Pt(tpy)(C≡C-CH(2)NMe(3))](OTf)(2) (2), has been studied by UV-vis, and steady-state and time-resolved emission spectroscopy. A unique FRET from PPE-SO(3)(-) to the aggregated complex 1 on the polymer chain with Pt···Pt interaction has been demonstrated, resulting in the growth of triplet metal-metal-to-ligand charge transfer ((3)MMLCT) emission in the near-infrared (NIR) region. This two-component ensemble has been employed in a "proof-of-principle" concept for the sensitive and selective label-free detection of human serum albumin (HSA) by the emission spectral changes in the visible and in the NIR region. The spectral changes have been ascribed to the disassembly of the polymer-metal complex aggregates upon the binding of PPE-SO(3)(-) to HSA, which is rich in arginine residues and hydrophobic patches, leading to the decrease in FRET from PPE-SO(3)(-) to the aggregated platinum(II) complex. The ensemble is found to have high selectivity toward HSA over a number of polyelectrolytes, proteins and small amino acids. This has been suggested to be a result of the extra stabilization gained from the Pt···Pt and π-π interactions in addition to the electrostatic and hydrophobic interactions found in the polymer-metal complex aggregates.

  1. Moisture Research - Optimizing Wall Assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L.; Mantha, P.

    2013-05-01

    The Consortium for Advanced Residential Buildings (CARB) evaluated several different configurations of wall assemblies to determine the accuracy of moisture modeling and make recommendations to ensure durable, efficient assemblies. WUFI and THERM were used to model the hygrothermal and heat transfer characteristics of these walls.

  2. Newnes electronics assembly pocket book

    CERN Document Server

    Brindley, Keith

    2013-01-01

    Produced in association with the Engineering Training Authority with contributions from dozens of people in the electronics industry. The material covers common skills in electrical and electronic engineering and concentrates mainly on wiring and assembly. 'Newnes Electronics Assembly Pocket Book' is for electronics technicians, students and apprentices.

  3. What was the Assembly Line?

    DEFF Research Database (Denmark)

    Nye, David

    2010-01-01

    The assembly line is still evolving a century after its invention, and it was not a distinct historical stage, nor was it part of an inevitable sequence that followed "Taylorism."......The assembly line is still evolving a century after its invention, and it was not a distinct historical stage, nor was it part of an inevitable sequence that followed "Taylorism."...

  4. A brief history of cell labelling

    International Nuclear Information System (INIS)

    Peters, A.M.

    2005-01-01

    The term cell labelling is usually used in the context of labelled leukocytes for imaging inflammation and labelled platelets for imaging thrombosis. Erythrocyte labelling for in vitro measurements of red cell life span, in vivo measurements of splenic red cell pooling, radionuclide ventriculography and imaging sites of bleeding has developed rather separately and has a different history. Labelled platelets and leukocytes were originally developed for cell kinetic studies. Since the current-day applications of labelled platelets and leukocytes depend on a clear understanding of cell kinetics, these classical studies are important and relevant to the history of cell labelling

  5. Recoil labelling of fluorine-18 labelled chlorofluoromethanes and tetrafluoromethane

    International Nuclear Information System (INIS)

    Palmer, A.J.

    1978-01-01

    18 F recoil labelling of trichlorofluoro-, dichlorodifluoro-, chlorotrifluoro- and tetrafluoromethane has been investigated. Mixtures of an appropriate substrate (0.3-2%) in neon were bombared with 14 MeV deuterons ( 20 Ne(d, α) 18 F reaction). All the above compounds were labelled in high activities by this technique. When tetrachloromethane was the substrate the major product was 18 F-trichlorofluoromethane (approximately 95% of total gaseous activity). 18 F-dichlorodifluoromethane was the major product (approximately 60 and approximately 70% respectively) when either trichlorofluoromethane or dichlorodifluoromethane was the substrate. The use of chlorotrifluoromethane as substrate produced 18 F-dichlorodifluoromethane and 18 F-tetrafluoromethane in significant amounts in addition to 18 F-chlorotrifluoromethane (approximately 40%). Bombardment of mixtures of tetrafluoromethane in neon produced 18 F-tetrafluoromethane (approximately 80%) together with other 18 F-labelled gaseous products. The targetry and irradiation conditions are described. the volatile products were analysed by radio-gas chromatography. (author)

  6. Advanced gray rod control assembly

    Energy Technology Data Exchange (ETDEWEB)

    Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O

    2013-09-17

    An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

  7. Control of extracellular matrix assembly by syndecan-2 proteoglycan

    DEFF Research Database (Denmark)

    Klass, C M; Couchman, J R; Woods, A

    2000-01-01

    Extracellular matrix (ECM) deposition and organization is maintained by transmembrane signaling and integrins play major roles. We now show that a second transmembrane component, syndecan-2 heparan sulfate proteoglycan, is pivotal in matrix assembly. Chinese Hamster Ovary (CHO) cells were stably....... The loss of matrix formation was not caused by a failure to synthesize or externalize ECM components as determined by metabolic labeling or due to differences in surface expression of alpha5 or beta1 integrin. The matrix assembly defect was at the cell surface, since S2deltaS cells also lost the ability...... to rearrange laminin or fibronectin substrates into fibrils and to bind exogenous fibronectin. Transfection of activated alphaIIbalphaLdeltabeta3 integrin into alpha(5)-deficient CHO B2 cells resulted in reestablishment of the previously lost fibronectin matrix. However, cotransfection of this cell line with S...

  8. Evaluation of students' opinion regarding food labelling

    OpenAIRE

    Budrytė, Indrė

    2016-01-01

    Evaluation of Students' Opinion Regarding Food Labelling. Food labeling is one of the main information sources that helps to improve consumers eating habits and maintain health. The aim of research: To evaluate Vilnius University Medicine and Economics faculties students’ opinion regarding food labelling and its impact to their food products choice. Tasks: 1) to evaluate students’ opinion regarding food labelling; 2) to evaluate students’ opinion regarding food labelling depending on the soci...

  9. Subcritical nuclear assembly

    Energy Technology Data Exchange (ETDEWEB)

    Vega C, H. R., E-mail: fermineutron@yahoo.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico)

    2014-08-15

    A Subcritical Nuclear Assembly is a device where the nuclear-fission chain reaction is initiated and maintained using an external neutron source. It is a valuable educational and research tool where in a safe way many reactor parameters can be measured. Here, we have used the Wigner-Seitz method in the six-factor formula to calculate the effective multiplication factor of a subcritical nuclear reactor Nuclear Chicago model 9000. This reactor has approximately 2500 kg of natural uranium heterogeneously distributed in slugs. The reactor uses a {sup 239}PuBe neutron source that is located in the center of an hexagonal array. Using Monte Carlo methods, with the MCNP5 code, a three-dimensional model of the subcritical reactor was designed to estimate the effective multiplication factor, the neutron spectra, the total and thermal neutron fluences along the radial and axial axis. With the neutron spectra in two locations outside the reactor the ambient dose equivalent were estimated. (Author)

  10. Flexible Foot Test Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Kurita, C.H.; /Fermilab

    1987-04-27

    A test model of the flexible foot support was constructed early in the design stages to check its reactions to applied loads. The prototype was made of SS 304 and contained four vertical plates as opposed to the fourteen Inconel 718 plates which comprise the actual structure. Due to the fact that the prototype was built before the design of the support was finalized, the plate dimensions are different from those of the actual proposed design (i.e. model plate thickness is approximately one-half that of the actual plates). See DWG. 3740.210-MC-222376 for assembly details of the test model and DWG. 3740.210-MB-222377 for plate dimensions. This stanchion will be required to not only support the load of the inner vessel of the cryostat and its contents, but it must also allow for the movement of the vessel due to thermal contraction. Assuming that each vertical plate acts as a column, then the following formula from the Manual of Steel Construction (American Institute of Steel Construction, Inc., Eigth edition, 1980) can be applied to determine whether or not such columns undergoing simultaneous axial compression and transverse loading are considered safe for the given loading. The first term is representative of the axially compressive stress, and the second term, the bending stress. If the actual compressive stress is greater than 15% of the allowable compressive stress, then there are additional considerations which must be accounted for in the bending stress term.

  11. Label-free drug discovery

    Directory of Open Access Journals (Sweden)

    Ye eFang

    2014-03-01

    Full Text Available Current drug discovery is dominated by label-dependent molecular approaches, which screen drugs in the context of a predefined and target-based hypothesis in vitro. Given that target-based discovery has not transformed the industry, phenotypic screen that identifies drugs based on a specific phenotype of cells, tissues, or animals has gained renewed interest. However, owing to the intrinsic complexity in drug-target interactions, there is often a significant gap between the phenotype screened and the ultimate molecular mechanism of action sought. This paper presents a label-free strategy for early drug discovery. This strategy combines label-free cell phenotypic profiling with computational approaches, and holds promise to bridge the gap by offering a kinetic and holistic representation of the functional consequences of drugs in disease relevant cells that is amenable to mechanistic deconvolution.

  12. Patient identification and tube labelling

    DEFF Research Database (Denmark)

    van Dongen-Lases, Edmée C; Cornes, Michael P; Grankvist, Kjell

    2016-01-01

    of phlebotomy procedures with the CLSI H3-A6 guideline was unacceptably low, and that patient identification and tube labelling are amongst the most critical steps in need of immediate attention and improvement. The process of patient identification and tube labelling is an essential safety barrier to prevent......Venous blood sampling (phlebotomy) is the most common invasive procedure performed in patient care. Guidelines on the correct practice of phlebotomy are available, including the H3-A6 guideline issued by the Clinical Laboratory Standards Institute (CLSI). As the quality of practices and procedures...... patient identity mix-up. Therefore, the EFLM Working Group aims to encourage and support worldwide harmonisation of patient identification and tube labelling procedures in order to reduce the risk of preanalytical errors and improve patient safety. With this Position paper we wish to raise awareness...

  13. Positron emitter labeled enzyme inhibitors

    International Nuclear Information System (INIS)

    Fowler, J.S.; MacGregor, R.R.; Wolf, A.P.; Langstrom, B.

    1990-01-01

    This invention involves a new strategy for imagining and mapping enzyme activity in the living human and animal body using positron emitter-labeled suicide enzyme inactivators or inhibitors which become covalently bound to the enzyme as a result of enzymatic catalysis. Two such suicide inactivators for monoamine oxidase have been labeled with carbon-11 and used to map the enzyme subtypes in the living human and animal body using PET. By using positron emission tomography to image the distribution of radioactivity produced by the body penetrating radiation emitted by carbon-11, a map of functionally active monoamine oxidase activity is obtained. Clorgyline and L-deprenyl are suicide enzyme inhibitors and irreversibly inhibit monoamine oxidase. When these inhibitors are labeled with carbon-11 they provide selective probes for monoamine oxidase localization and reactivity in vivo using positron emission tomography

  14. Radioisotope methods for leucocyte labelling

    International Nuclear Information System (INIS)

    Kostadinova, I.; Kovacheva, S.

    1988-01-01

    A review is made of the labelling methods with the following tracers: 3 H-thymidine, 32 P-DP, 111 In (oxine, tropolon, acetylacetone, MERC), 99m Tc (reduced 99m Tc, lypophyl 99m Tc-complexes and 99m Tc-colloids). The main diagnosis areas are mentioned: abdominal abscesses and inflammations, inflammation foci of skeleton or of implanted prosthesis; acute myocardial infarction, bacterial endocarditis, rejection of kydney transplantations or vascular grafts. It is concluded that labelled leucocytes are very reliable for noninvasive diagnosis of inflammation foci with unclear localization

  15. Melatonin labelled by hydrogen isotopes

    International Nuclear Information System (INIS)

    Dmitrevskaya, L.I.; Smushkevich, Yu.I.; Kurkovskaya, L.N.; Ponomarenko, N.K.; Suvorov, N.N.

    1988-01-01

    Isotope exchange of melatonin with deuterium (D 2 O) and tritium (HTO) oxides under different conditions is studied. Simplicity of isotope exchange of hydrogens of the indole ring of melatonin in the acidic medium decreases in series H 4 >H 2 >H 6 >>H 7 , that permits to suggest the way of melatonin preparation labelled by hydrogen isotopes in positions 4,6 and 2 of the indole ring. The way of melatonin preparation labelled by hydrogen isotopes in position 2 according to the reaction of desulfation 2-(2,4-dinitrophenylsulphenyl) melatonin at catalyst Ni(Re)(D) is suggested

  16. Denture labeling: A new approach

    Directory of Open Access Journals (Sweden)

    Pardeep K Bansal

    2011-01-01

    Full Text Available The need for denture labeling is important for forensic and social reasons in case patients need to be identified individually. The importance of denture marking has long been acknowledged by the dental profession. Over the years, various denture marking systems have been reported in the literature, but none till date fulfills all the prescribed ADA specifications. A simple, easy, inexpensive procedure for marking accurate identification marks on dentures with a lead foil is described here. The label caring the patient information is incorporated in the acrylic resin during the denture processing.

  17. Melatonin labeled with hydrogen isotopes

    International Nuclear Information System (INIS)

    Dmitrevskaya, L.I.; Smushkevich, Yu.I.; Kurkovskaya, L.N.; Ponomarenko, N.K.; Suvorov, N.N.

    1989-01-01

    A study has been made of isotope exchange between melatonin and deuterium (D 2 O) or tritium (HTO) oxide under different conditions. The ease of isotope exchange for the indole ring hydrogens of melatonin in an acidic medium decreases over the series H 4 > H 2 H 6 >> H 7 , enabling the authors to process a route for production of melatonin labeled with hydrogen isotopes at positions 4,6, and 2 of the indole ring. A method has been suggested for producing melatonin labeled with hydrogen isotopes at position 2 by desulfurization of 2-(2,4-dinitro-phenylsulfenyl)melatonin at Ni(Re) (D)

  18. Bearing assemblies, apparatuses, and motor assemblies using the same

    Science.gov (United States)

    Sexton, Timothy N.; Cooley, Craig H.; Knuteson, Cody W.

    2015-12-29

    Various embodiments of the invention relate to bearing assemblies, apparatuses and motor assemblies that include geometric features configured to impart a selected amount of heat transfer and/or hydrodynamic film formation. In an embodiment, a bearing assembly may include a plurality of superhard bearing pads distributed circumferentially about an axis. At least some of the plurality of superhard bearing pads may include a plurality of sub-superhard bearing elements defining a bearing surface. At least some of the plurality of sub-superhard bearing elements may be spaced from one another by one or more voids to impart a selected amount of heat transfer and hydrodynamic film formation thereon during operation. The bearing assembly may also include a support ring that carries the plurality of superhard bearing pads. In addition, at least a portion of the sub-superhard bearing elements may extend beyond the support ring.

  19. Assembly line performance and modeling

    Science.gov (United States)

    Rane, Arun B.; Sunnapwar, Vivek K.

    2017-09-01

    Automobile sector forms the backbone of manufacturing sector. Vehicle assembly line is important section in automobile plant where repetitive tasks are performed one after another at different workstations. In this thesis, a methodology is proposed to reduce cycle time and time loss due to important factors like equipment failure, shortage of inventory, absenteeism, set-up, material handling, rejection and fatigue to improve output within given cost constraints. Various relationships between these factors, corresponding cost and output are established by scientific approach. This methodology is validated in three different vehicle assembly plants. Proposed methodology may help practitioners to optimize the assembly line using lean techniques.

  20. Lateral loadings on snubber assemblies

    International Nuclear Information System (INIS)

    Raphael, L.S.

    1981-01-01

    This paper examines the installation of snubber assemblies in power plants with respect to transverse or lateral loads as well as axial loads. Evaluation of the effects of low level, lateral loads was performed by analytical means. At higher loadings, the snubber assembly could no longer be treated as a column; therefore, the effects of lateral loadings was determined by test. The test consisted of applying both lateral and axial loads simultaneously. Results of both the analysis and the test showed that the application of lateral loads had a considerable effect on the snubber assemblies

  1. Fuel assembly in a reactor

    International Nuclear Information System (INIS)

    Saito, Shozo; Kawahara, Akira.

    1975-01-01

    Object: To provide a fuel assembly in a reactor which can effectively prevent damage of the clad tube caused by mutual interference between pellets and the clad tube. Structure: A clad tube for a fuel element, which is located in the outer peripheral portion, among the fuel elements constituting fuel assemblies arranged in assembled and lattice fashion within a channel box, is increased in thickness by reducing the inside diameter thereof to be smaller than that of fuel elements internally located, thereby preventing damage of the clad tube resulting from rapid rise in output produced when control rods are removed. (Kamimura, M.)

  2. Illustrating how mechanical assemblies work

    KAUST Repository

    Mitra, Niloy J.

    2010-07-26

    How things work visualizations use a variety of visual techniques to depict the operation of complex mechanical assemblies. We present an automated approach for generating such visualizations. Starting with a 3D CAD model of an assembly, we first infer the motions of individual parts and the interactions between parts based on their geometry and a few user specified constraints. We then use this information to generate visualizations that incorporate motion arrows, frame sequences and animation to convey the causal chain of motions and mechanical interactions between parts. We present results for a wide variety of assemblies. © 2010 ACM.

  3. Illustrating how mechanical assemblies work

    KAUST Repository

    Mitra, Niloy J.

    2013-01-01

    How-things-work visualizations use a variety of visual techniques to depict the operation of complex mechanical assemblies. We present an automated approach for generating such visualizations. Starting with a 3D CAD model of an assembly, we first infer the motions of the individual parts and the interactions across the parts based on their geometry and a few user-specified constraints. We then use this information to generate visualizations that incorporate motion arrows, frame sequences, and animation to convey the causal chain of motions and mechanical interactions across parts. We demonstrate our system on a wide variety of assemblies. © 2013 ACM 0001-0782/13/01.

  4. Directed Assembly of Gold Nanoparticles

    DEFF Research Database (Denmark)

    Westerlund, Axel Rune Fredrik; Bjørnholm, Thomas

    2009-01-01

    As a complement to common "top-down" lithography techniques, "bottom-up" assembly techniques are emerging as promising tools to build nanoscale structures in a predictable way. Gold nanoparticles that are stable and relatively easy to synthesize are important building blocks in many such structures...... due to their useful optical and electronic properties. Programmed assembly of gold nanoparticles in one, two, and three dimensions is therefore of large interest. This review focuses on the progress from the last three years in the field of directed gold nanoparticle and nanorod assembly using...

  5. Food quality labels from the producers’ perspective

    Directory of Open Access Journals (Sweden)

    Šárka Velčovská

    2016-09-01

    Full Text Available The paper deals with analysing the food producer attitudes towards quality labels. The Klasa label, as the most known and the most frequently used food quality label in the Czech Republic, have become the subject of investigation. The aim of the research was to identify the benefits and problems arising from the certification process and the label use. Primary data were collected in online survey based on standardized questionnaire. In census, 86 respondents from the total 218 producers with the Klasa label in the Czech Republic completed the questionnaire. The most of producers (72% have a longer experience with the label, they are using the label for more than four years. The producers’ expectations from the label were fulfilled only partially. A poor state marketing support and missing marketing strategy were identified as general problems of the label. Specific perceived problems are formalities connected with the certification process and certification of poor-quality products. Correlation analysis, t-test and Pearson chi-square test were calculated to discover relations between variables. The results of the study can be beneficial to both, food producers as well as administrator of the label. Identified problems could help them to improve marketing strategy of the label in order to manage the label in effective way and use all benefits arising from the certification. Administrator of the label should make the certification process more effective and transparent, promotion should be focused on the explanation to consumers what the Klasa label guarantees.

  6. Specific labeling and assignment strategies of valine methyl groups for NMR studies of high molecular weight proteins

    International Nuclear Information System (INIS)

    Mas, Guillaume; Crublet, Elodie; Hamelin, Olivier; Gans, Pierre; Boisbouvier, Jérôme

    2013-01-01

    The specific protonation of valine and leucine methyl groups in proteins is typically achieved by overexpressing proteins in M9/D 2 O medium supplemented with either labeled α-ketoisovalerate for the labeling of the four prochiral methyl groups or with 2-acetolactate for the stereospecific labeling of the valine and leucine side chains. However, when these labeling schemes are applied to large protein assemblies, significant overlap between the correlations of the valine and leucine methyl groups occurs, hampering the analysis of 2D methyl-TROSY spectra. Analysis of the leucine and valine biosynthesis pathways revealed that the incorporation of labeled precursors in the leucine pathway can be inhibited by the addition of exogenous l-leucine-d 10 . We exploited this property to label stereospecifically the pro-R and pro-S methyl groups of valine with minimal scrambling to the leucine residues. This new labeling protocol was applied to the 468 kDa homododecameric peptidase TET2 to decrease the complexity of its NMR spectra. All of the pro-S valine methyl resonances of TET2 were assigned by combining mutagenesis with this innovative labeling approach. The assignments were transferred to the pro-R groups using an optimally labeled sample and a set of triple resonance experiments. This improved labeling scheme enables us to overcome the main limitation of overcrowding in the NMR spectra of prochiral methyl groups, which is a prerequisite for the site-specific measurement of the structural and dynamic parameters or for the study of interactions in very large protein assemblies

  7. Specific labeling and assignment strategies of valine methyl groups for NMR studies of high molecular weight proteins

    Energy Technology Data Exchange (ETDEWEB)

    Mas, Guillaume; Crublet, Elodie [Univ. Grenoble Alpes, Institut de Biologie Structurale (IBS) (France); Hamelin, Olivier [CNRS (France); Gans, Pierre; Boisbouvier, Jérôme, E-mail: jerome.boisbouvier@ibs.fr [Univ. Grenoble Alpes, Institut de Biologie Structurale (IBS) (France)

    2013-09-28

    The specific protonation of valine and leucine methyl groups in proteins is typically achieved by overexpressing proteins in M9/D{sub 2}O medium supplemented with either labeled α-ketoisovalerate for the labeling of the four prochiral methyl groups or with 2-acetolactate for the stereospecific labeling of the valine and leucine side chains. However, when these labeling schemes are applied to large protein assemblies, significant overlap between the correlations of the valine and leucine methyl groups occurs, hampering the analysis of 2D methyl-TROSY spectra. Analysis of the leucine and valine biosynthesis pathways revealed that the incorporation of labeled precursors in the leucine pathway can be inhibited by the addition of exogenous l-leucine-d{sub 10}. We exploited this property to label stereospecifically the pro-R and pro-S methyl groups of valine with minimal scrambling to the leucine residues. This new labeling protocol was applied to the 468 kDa homododecameric peptidase TET2 to decrease the complexity of its NMR spectra. All of the pro-S valine methyl resonances of TET2 were assigned by combining mutagenesis with this innovative labeling approach. The assignments were transferred to the pro-R groups using an optimally labeled sample and a set of triple resonance experiments. This improved labeling scheme enables us to overcome the main limitation of overcrowding in the NMR spectra of prochiral methyl groups, which is a prerequisite for the site-specific measurement of the structural and dynamic parameters or for the study of interactions in very large protein assemblies.

  8. On Labeled Traveling Salesman Problems

    DEFF Research Database (Denmark)

    Couetoux, Basile; Gourves, Laurent; Monnot, Jerome

    2008-01-01

    We consider labeled Traveling Salesman Problems, defined upon a complete graph of n vertices with colored edges. The objective is to find a tour of maximum (or minimum) number of colors. We derive results regarding hardness of approximation, and analyze approximation algorithms for both versions...

  9. Food Labels Tell the Story!

    Science.gov (United States)

    ... to the Table! Food Labels Tell the Story! What is in food? Food provides your body with all of the ... need from every group? How did you do? What recommendations can you make? Eating a healthy diet doesn't mean giving up your favorite foods. Just balance your food choices. Nutrition Facts—the ...

  10. Psychological effectiveness of carbon labelling

    Science.gov (United States)

    Beattie, Geoffrey

    2012-04-01

    Despite the decision by supermarket-giant Tesco to delay its plan to add carbon-footprint information onto all of its 70,000 products, carbon labelling, if carefully designed, could yet change consumer behaviour. However, it requires a new type of thinking about consumers and much additional work.

  11. When Diagnostic Labels Mask Trauma

    Science.gov (United States)

    Foltz, Robert; Dang, Sidney; Daniels, Brian; Doyle, Hillary; McFee, Scott; Quisenberry, Carolyn

    2013-01-01

    A growing body of research shows that many seriously troubled children and adolescents are reacting to adverse life experiences. Yet traditional diagnostic labels are based on checklists of surface symptoms. Distracted by disruptive behavior, the common response is to medicate, punish, or exclude rather than respond to needs of youth who have…

  12. Synthesis of labelled ecdysone precursors

    International Nuclear Information System (INIS)

    Haag, T.; Hetru, C.; Nakatani, Y.; Luu, B.; Meister, M.; Pichat, L.; Audinot, M.

    1985-01-01

    High specific activity tritiated 3β,14α-dihydroxy-5β-cholest-7-en-6-one, has been prepared using a precursor which permits rapid and easy labelling. This compound is converted to ecdysone under in vitro conditions by insect prothoracic glands, a well known site of ecdysone biosynthesis. (author)

  13. Symmetry in labeled transition systems

    NARCIS (Netherlands)

    I.A. van Langevelde

    2003-01-01

    textabstractSymmetry is defined for labeled transition systems, and it is shown how symmetrical systems can be symmetrically decomposed into components. The central question is under what conditions one such component may represent the whole system, in the sense that one symmetrical system is

  14. Improving the energy labelling scheme

    DEFF Research Database (Denmark)

    Gram-Hanssen, Kirsten; Christensen, Toke Haunstrup

    This report summarises the main results of an EU project on consumer response to energy labels in buildings. This report is mainly directed at Danish policy makers. The main focus is therefore on results that are relevant from a Danish point of view and on how they can be used to further strengthen...

  15. Assembly of the 30S subunit from Escherichia coli ribosomes occurs via two assembly domains which are initiated by S4 and S7

    International Nuclear Information System (INIS)

    Nowotny, V.; Nierhaus, K.H.

    1988-01-01

    A protein which initiates assembly of ribosomes is defined as a protein which binds to the respective rRNA without cooperativity (i.e., without the help of other proteins) during the onset of assembly and is essential for the formation of active ribosomal subunits. The number of proteins binding without cooperativity was determined by monitoring the reconstitution output of active particles at various inputs of 16S rRNA, in the present of constant amounts of 30S-derived proteins (TP30): This showed that only two of the proteins of the 30S subunit are assembly-initiator proteins. These two proteins are still present on a LiCl core particle comprising 16S rRNA and 12 proteins (including minor proteins). The 12 proteins were isolated, and a series of reconstitution experiments at various levels of rRNA excess demonstrated that S4 and S7 are the initiator proteins. Pulse-chase experiments performed during the early assembly with 14 C- and 3 H-labeled TP30 and the determination of the 14 C/ 3 H ratio of the individual proteins within the assembled particles revealed a bilobal structure of the 30S assembly: A group of six proteins headed by S4 (namely, S4, S20, S16, S15, S6, and S18) resisted the chasing most efficiently (S4 assembly domain). None of the proteins depending on S7 during assembly were found in this group but rather in a second group with intermediate chasing stability [S7 assembly domain; consisting of S7, S9, (S8), S19, and S3]. A number of proteins could be fully chased during the early assembly and therefore represent late assembly proteins (S10, S5, S13, S2, S21, S1). These findings fit well with the 30S assembly map. These data, together with the assembly map, imply that S8 and S5 play an important role in the interconnection of the two assembly domains

  16. Irradiated fuel assembly restoration equipment

    International Nuclear Information System (INIS)

    Guironnet, L.

    1993-01-01

    Analysis of in-plant fuel operating experience shows that assembly damage has a variety of causes: Handling incidents; external hazards during operation; wear and perforation; fuel manufacturing defects and other causes. Depending on the seriousness of the damage and the burnup level reached by assemblies, several repair possibilities arise: If they are leaktight and if grid distortion is minimal and does not jeopardize rod restraint, they are reloaded, subject to local servicing for restoring acceptable grid geometry. In all other cases, the assemblies have to be restored either by replacing the damaged skeleton or be replacing the leaking rod(s). This paper presents methods, equipments and the FRAGEMA experience in assemblies repair. (author). 5 pictures, 3 diagrams

  17. Analysis of Illumina Microbial Assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Clum, Alicia; Foster, Brian; Froula, Jeff; LaButti, Kurt; Sczyrba, Alex; Lapidus, Alla; Woyke, Tanja

    2010-05-28

    Since the emerging of second generation sequencing technologies, the evaluation of different sequencing approaches and their assembly strategies for different types of genomes has become an important undertaken. Next generation sequencing technologies dramatically increase sequence throughput while decreasing cost, making them an attractive tool for whole genome shotgun sequencing. To compare different approaches for de-novo whole genome assembly, appropriate tools and a solid understanding of both quantity and quality of the underlying sequence data are crucial. Here, we performed an in-depth analysis of short-read Illumina sequence assembly strategies for bacterial and archaeal genomes. Different types of Illumina libraries as well as different trim parameters and assemblers were evaluated. Results of the comparative analysis and sequencing platforms will be presented. The goal of this analysis is to develop a cost-effective approach for the increased throughput of the generation of high quality microbial genomes.

  18. Shingle assembly with support bracket

    Science.gov (United States)

    Almy, Charles

    2007-01-02

    A shingle system, mountable to a support surface, includes overlapping shingle assemblies. Each shingle assembly comprises a support bracket, having upper and lower ends, secured to a shingle body. The upper end has an upper support portion, extending away from the shingle body, and an upper support-surface-engaging part, engageable with a support surface so that the upper edge of the shingle body is positionable at a first distance from the support surface to create a first gap therebetween. The lower end has a lower support portion extending away from the lower surface. The support brackets create: (1) a second gap between shingle bodies of the first and second shingle assemblies, and (2) an open region beneath the first shingle assembly fluidly coupling the first and second gaps.

  19. Multiple complementary gas distribution assemblies

    Science.gov (United States)

    Ng, Tuoh-Bin; Melnik, Yuriy; Pang, Lily L; Tuncel, Eda; Nguyen, Son T; Chen, Lu

    2016-04-05

    In one embodiment, an apparatus includes a first gas distribution assembly that includes a first gas passage for introducing a first process gas into a second gas passage that introduces the first process gas into a processing chamber and a second gas distribution assembly that includes a third gas passage for introducing a second process gas into a fourth gas passage that introduces the second process gas into the processing chamber. The first and second gas distribution assemblies are each adapted to be coupled to at least one chamber wall of the processing chamber. The first gas passage is shaped as a first ring positioned within the processing chamber above the second gas passage that is shaped as a second ring positioned within the processing chamber. The gas distribution assemblies may be designed to have complementary characteristic radial film growth rate profiles.

  20. Fuel assemblies for nuclear reactors

    International Nuclear Information System (INIS)

    Leonard, B.H. Jr.

    1975-01-01

    A description is given of a fuel assembly for a nuclear reactor comprising a plurality of elongated plate-like fuel bearing elements of the same length and width, paired longer than they are wide and assembly spacer members having means defining opposed spaced notches for receiving the side edges of said elongated plate-like fuel bearing elements, and means for securing said plate-like fuel bearing elements to said paired assembly spacer members with the side edges of said plate-like elements engaged in opposite notches in said paired assembly spacer elements so as to secure said fuel bearing elements in side by side spaced relation in a staggered arrangement transversely so as to conform to a diamond shaped profile in which opposite sides are parallel and opposite angles are substantially 60 0 and substantially 120 0

  1. Direct hierarchical assembly of nanoparticles

    Science.gov (United States)

    Xu, Ting; Zhao, Yue; Thorkelsson, Kari

    2014-07-22

    The present invention provides hierarchical assemblies of a block copolymer, a bifunctional linking compound and a nanoparticle. The block copolymers form one micro-domain and the nanoparticles another micro-domain.

  2. Solar cell module assembly jig

    Science.gov (United States)

    Ofarrell, H. W. (Inventor)

    1966-01-01

    The invention relates to the manufacture of solar cell modules and more particularly to a jig for assembling, positioning and maintaining the components under resilient pressure, while the entire assembly and the jig is subjected to heat for simultaneously soldering all of the various circuit connections; as well as structurally bonding the layers into a strong light weight structure which minimizes the tendency of the solar cells to crack and the other components and electrical connections to fracture.

  3. Assembly delay line pulse generators

    CERN Multimedia

    CERN PhotoLab

    1971-01-01

    Assembly of six of the ten delay line pulse generators that will power the ten kicker magnet modules. One modulator part contains two pulse generators. Capacitors, inductances, and voltage dividers are in the oil tank on the left. Triggered high-pressure spark gap switches are on the platforms on the right. High voltage pulse cables to the kicker magnet emerge under the spark gaps. In the centre background are the assembled master gaps.

  4. Another successful Doctoral Student Assembly

    CERN Multimedia

    Katarina Anthony

    2014-01-01

    On Wednesday 2 April, CERN hosted its third Doctoral Student Assembly in the Council Chamber.   CERN PhD students show off their posters in CERN's Main Building. Speaking to a packed house, Director-General Rolf Heuer gave the assembly's opening speech and introduced the poster session that followed. Seventeen CERN PhD students presented posters on their work, and were greeted by their CERN and University supervisors. It was a very successful event!

  5. BRET fuel assembly dismantling machine

    International Nuclear Information System (INIS)

    Titzler, P.A.; Bennett, K.L.; Kelley, R.S. Jr.; Stringer, J.L.

    1984-08-01

    An automated remote nuclear fuel assembly milling and dismantling machine has been designed, developed, and demonstrated at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington. The machine can be used to dismantle irradiated breeder fuel assemblies from the Fast Flux Test Facility prior to fuel reprocessing. It can be installed in an existing remotely operated shielded hot cell facility, the Fuels and Materials Examination Facility (FMEF), at the Hanford Site in Richland, Washington

  6. Labelling fashion magazine advertisements: Effectiveness of different label formats on social comparison and body dissatisfaction.

    Science.gov (United States)

    Tiggemann, Marika; Brown, Zoe

    2018-03-08

    The experiment investigated the impact on women's body dissatisfaction of different forms of label added to fashion magazine advertisements. Participants were 340 female undergraduate students who viewed 15 fashion advertisements containing a thin and attractive model. They were randomly allocated to one of five label conditions: no label, generic disclaimer label (indicating image had been digitally altered), consequence label (indicating that viewing images might make women feel bad about themselves), informational label (indicating the model in the advertisement was underweight), or a graphic label (picture of a paint brush). Although exposure to the fashion advertisements resulted in increased body dissatisfaction, there was no significant effect of label type on body dissatisfaction; no form of label demonstrated any ameliorating effect. In addition, the consequence and informational labels resulted in increased perceived realism and state appearance comparison. Yet more extensive research is required before the effective implementation of any form of label. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Requirements for Access to Pesticide Labeling Information

    Science.gov (United States)

    Employers of pesticide handlers must make sure that the handlers are given information from the pesticide labeling and have access to the labeling itself, before they do any handling task. Learn about the information employers must provide.

  8. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Infections Diseases & Conditions Pregnancy & Baby Nutrition & Fitness Emotions & Behavior School & Family Life First Aid & Safety Doctors & Hospitals ... label. These labels have a lot of important information — on fat and calories, serving sizes, sodium content, ...

  9. Soil Fumigant Labels - Metam Sodium/Potassium

    Science.gov (United States)

    Search by EPA registration number, product name, or company; and follow the link to the Pesticide Product Label System (PPLS) for details. Updated labels include new safety requirements for buffer zones and related measures.

  10. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Answers (Q&A) Staying Safe Videos for Educators ... packaged foods come with a Nutrition Facts label. These labels have a lot of important information — on fat and calories, serving sizes, sodium content, ...

  11. Labelling schemes: From a consumer perspective

    DEFF Research Database (Denmark)

    Juhl, Hans Jørn; Stacey, Julia

    2000-01-01

    Labelling of food products attracts a lot of political attention these days. As a result of a number of food scandals, most European countries have acknowledged the need for more information and better protection of consumers. Labelling schemes are one way of informing and guiding consumers....... However, initiatives in relation to labelling schemes seldom take their point of departure in consumers' needs and expectations; and in many cases, the schemes are defined by the institutions guaranteeing the label. It is therefore interesting to study how consumers actually value labelling schemes....... A recent MAPP study has investigated the value consumers attach the Government-controlled labels 'Ø-mærket' and 'Den Blå Lup' and the private supermarket label 'Mesterhakket' when they purchase minced meat. The results reveal four consumer segments that use labelling schemes for food products very...

  12. Consumer knowledge and attitudes toward nutritional labels.

    Science.gov (United States)

    Cannoosamy, Komeela; Pugo-Gunsam, Prity; Jeewon, Rajesh

    2014-01-01

    To determine Mauritian consumers' attitudes toward nutritional labels based on the Kano model and to identify determinants of the use and understanding of nutrition labels. The researchers also used a Kano model questionnaire to determine consumers' attitudes toward nutrition labeling. Four hundred consumers residing in Mauritius. Information was elicited via a questionnaire that assessed nutritional knowledge and information about the use and understanding of nutritional labels and demographic factors. Nutritional label use and understanding, nutrition knowledge, and association of demographic factors with label use. Statistical tests performed included 1-way ANOVA and independent samples t tests. Statistically significant relationships (P consumer dissatisfaction. Age, education, income, household size, and nutrition knowledge had an impact on nutritional label use. Health promoters should aim to increase the use of nutritional labels. Copyright © 2014 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

  13. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... a lot of important information — on fat and calories, serving sizes, sodium content, and more — but they' ... Labels Smart Supermarket Shopping Figuring Out Fat and Calories Food Labels View more Partner Message About Us ...

  14. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Staying Safe Videos for Educators Search English Español How to Read a Nutrition Facts Label (Video) KidsHealth / For Parents / How to Read a Nutrition Facts Label (Video) Print ...

  15. Enzymatic synthesis of isotopically labelled purine deoxyribonucleotides

    International Nuclear Information System (INIS)

    Frank-Kamenetskaya, M.D.; Myasoedov, N.F.

    1992-01-01

    An enzymatic method is described which makes it possible to synthesize labelled purine deoxyribonucleotides from corresponding labelled purine ribonucleotides using the RDP-reductase system of ether-treated E. coli E125 cells. (Author)

  16. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... site Sitio para adolescentes Body Mind Sexual Health Food & Fitness Diseases & Conditions Infections Drugs & Alcohol School & Jobs ... las etiquetas de datos nutricionales (video) Most packaged foods come with a Nutrition Facts label. These labels ...

  17. Self-Assembled Polyelectrolyte Nanoparticles as Fluorophore-Free Contrast Agents for Multicolor Optical Imaging

    Directory of Open Access Journals (Sweden)

    Da Hye Shin

    2015-03-01

    Full Text Available In this work, we describe the fabrication of self-assembled polyelectrolyte nanoparticles that provide a multicolor optical imaging modality. Poly(γ-glutamic acid(γ-PGA formed self-assembled nanoparticles through electrostatic interactions with two different cationic polymers: poly(L-lysine(PLL and chitosan. The self-assembled γ-PGA/PLL and γ-PGA/chitosan nanoparticles were crosslinked by glutaraldehyde. Crosslinking of the ionic self-assembled nanoparticles with glutaraldehyde not only stabilized the nanoparticles but also generated a strong autofluorescence signal. Fluorescent Schiff base bonds (C=N and double bonds (C=C were generated simultaneously by crosslinking of the amine moiety of the cationic polyelectrolytes with monomeric glutaraldehyde or with polymeric glutaraldehyde. The unique optical properties of the nanoparticles that resulted from the crosslinking by glutaraldehyde were analyzed using UV/Vis and fluorescence spectroscopy. We observed that the fluorescence intensity of the nanoparticles could be regulated by adjusting the crosslinker concentration and the reaction time. The nanoparticles also exhibited high performance in the labeling and monitoring of therapeutic immune cells (macrophages and dendritic cells. These self-assembled nanoparticles are expected to be a promising multicolor optical imaging contrast agent for the labeling, detection, and monitoring of cells.

  18. 49 CFR 172.430 - POISON label.

    Science.gov (United States)

    2010-10-01

    ... be white. The word “TOXIC” may be used in lieu of the word “POISON”. [Amdt. 172-123, 56 FR 66258, Dec... 49 Transportation 2 2010-10-01 2010-10-01 false POISON label. 172.430 Section 172.430... SECURITY PLANS Labeling § 172.430 POISON label. (a) Except for size and color, the POISON label must be as...

  19. DNA-mediated self-assembly of tetrahedral plasmonic clusters for metafluids

    Science.gov (United States)

    Schade, Nicholas; Sun, Li; Lee, You-Jin; Fan, Jonathan; Capasso, Federico; Yi, Gi-Ra; Manoharan, Vinothan

    2014-03-01

    We direct the self-assembly of clusters of gold nanospheres with the goal of creating a bulk, isotropic, optical metafluid. We use spherical gold nanoparticles that are exceptionally smooth, monocrystalline, and monodisperse. These particles exhibit highly reproducible scattering spectra compared with commercially available gold colloids. We label them with DNA sequences and mix them together to self-assemble small clusters. By controlling the particle sizes and the interactions between them, we maximize the yield of tetrahedral clusters, the ideal structures for isotropic metamaterials.

  20. Molecular self-assembly advances and applications

    CERN Document Server

    Dequan, Alex Li

    2012-01-01

    In the past several decades, molecular self-assembly has emerged as one of the main themes in chemistry, biology, and materials science. This book compiles and details cutting-edge research in molecular assemblies ranging from self-organized peptide nanostructures and DNA-chromophore foldamers to supramolecular systems and metal-directed assemblies, even to nanocrystal superparticles and self-assembled microdevices

  1. Self-Assembly of Infinite Structures

    Directory of Open Access Journals (Sweden)

    Scott M. Summers

    2009-06-01

    Full Text Available We review some recent results related to the self-assembly of infinite structures in the Tile Assembly Model. These results include impossibility results, as well as novel tile assembly systems in which shapes and patterns that represent various notions of computation self-assemble. Several open questions are also presented and motivated.

  2. Subcritical assemblies, use and their feasibility assessment

    International Nuclear Information System (INIS)

    Haroon, M.R.

    1982-03-01

    In developing countries, subcritical assemblies can be a useful tool for training and research in the field of nuclear technology with minimum cost. The historical development of subcritical assemblies and the reactor physics experiments which can be carried out using this facility are outlined. The different types of subcritical assemblies have been described and material requirements for each assembly have been pointed out. (author)

  3. 99mTc: Labeling Chemistry and Labeled Compounds

    Science.gov (United States)

    Alberto, R.; Abram, U.

    This chapter reviews the radiopharmaceutical chemistry of technetium related to the synthesis of perfusion agents and to the labeling of receptor-binding biomolecules. To understand the limitations of technetium chemistry imposed by future application of the complexes in nuclear medicine, an introductory section analyzes the compulsory requirements to be considered when facing the incentive of introducing a novel radiopharmaceutical into the market. Requirements from chemistry, routine application, and market are discussed. In a subsequent section, commercially available 99mTc-based radiopharmaceuticals are treated. It covers the complexes in use for imaging the most important target organs such as heart, brain, or kidney. The commercially available radiopharmaceuticals fulfill the requirements outlined earlier and are discussed with this background. In a following section, the properties and perspectives of the different generations of radiopharmaceuticals are described in a general way, covering characteristics for perfusion agents and for receptor-specific molecules. Technetium chemistry for the synthesis of perfusion agents and the different labeling approaches for target-specific biomolecules are summarized. The review comprises a general introduction to the common approaches currently in use, employing the N x S4-x , [3+1] and 2-hydrazino-nicotinicacid (HYNIC) method as well as more recent strategies such as the carbonyl and the TcN approach. Direct labeling without the need of a bifunctional chelator is briefly reviewed as well. More particularly, recent developments in the labeling of concrete targeting molecules, the second generation of radiopharmaceuticals, is then discussed and prominent examples with antibodies/peptides, neuroreceptor targeting small molecules, myocardial imaging agents, vitamins, thymidine, and complexes relevant to multidrug resistance are given. In addition, a new approach toward peptide drug development is described. The section

  4. 40 CFR 86.1606 - Labeling.

    Science.gov (United States)

    2010-07-01

    ... must be of a color that contrasts with the background of the label: (1) The label heading: Vehicle... EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Regulations for Altitude Performance Adjustments for New and In-Use Motor Vehicles and Engines § 86.1606 Labeling. (a) The manufacturer shall make...

  5. What determines consumer attention to nutrition labels?

    NARCIS (Netherlands)

    Bialkova, S.E.; Trijp, van J.C.M.

    2010-01-01

    To identify the key determinants of consumer attention to nutrition labels, visual search tasks (present – absent; one – two targets) were used as an effective experimental tool. The main manipulation concerned: set size (number of labels on front of pack); label characteristics (display size,

  6. 10 CFR 61.57 - Labeling.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Labeling. 61.57 Section 61.57 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSING REQUIREMENTS FOR LAND DISPOSAL OF RADIOACTIVE WASTE Technical Requirements for Land Disposal Facilities § 61.57 Labeling. Each package of waste must be clearly labeled to...

  7. 21 CFR 820.120 - Device labeling.

    Science.gov (United States)

    2010-04-01

    ... designed to prevent mixups. (d) Labeling operations. Each manufacturer shall control labeling and packaging... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Device labeling. 820.120 Section 820.120 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES...

  8. 7 CFR 56.73 - Misleading labeling.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Misleading labeling. 56.73 Section 56.73 Agriculture... EGGS Grading of Shell Eggs Denial of Service § 56.73 Misleading labeling. The use of the terms “Government Graded”, “Federal-State Graded”, or terms of similar import in the labeling or advertising of any...

  9. Multi-label Learning for Detection of CME-Associated Phenomena

    Science.gov (United States)

    Yang, Y. H.; Tian, H. M.; Peng, B.; Li, T. R.; Xie, Z. X.

    2017-09-01

    Coronal mass ejections (CMEs) are considered as one of the driving sources of space weather. They are usually associated with many physical phenomena, e.g. flares, coronal dimmings, and sigmoids. To detect these phenomena, traditional supervised-learning methods assumed that at most one event occurred in a CME; therefore each CME instance is associated with a single label and the phenomenon is processed in isolation. This simplifying assumption does not fit well, as CMEs might have multiple events simultaneously. We propose to detect multiple CME-associated events by multi-label learning methods. With the data available from the Atmospheric Imaging Assembly (AIA) and the Large Angle and Spectrometric Coronagraph (LASCO), texture features representing the events are extracted from all of the associated and not-associated CMEs and converted into feature vectors for multi-label learning use. Then a function is learned to predict the proper label sets for CMEs, such that eight events, i.e. coronal dimming, coronal hole, coronal jet, coronal wave, filament, filament eruption, flare, and sigmoid, are detected explicitly. To test the proposed detection algorithm, we adopt the four-fold cross-validation strategy on a set of 551 labeled CMEs from AIA. Experimental results demonstrate the good performance of the multi-label classification methods in terms of test error.

  10. White Label Space GLXP Mission

    Science.gov (United States)

    Barton, A.

    2012-09-01

    This poster presents a lunar surface mission concept and corresponding financing approach developed by the White Label Space team, an official competitor in the Google Lunar X PRIZE. The White Label Space team's origins were in the European Space Agency's ESTEC facility in the Netherlands. Accordingly the team's technical headquarters are located just outside ESTEC in the Space Business Park. The team has active partners in Europe, Japan and Australia. The team's goal is to provide a unique publicity opportunity for global brands to land on the moon and win the prestigious Google Lunar X PRIZE. The poster presents the main steps to achieve this goal, the cost estimates for the mission, describes the benefits to the potential sponsors and supporters, and details the progress achieved to date.

  11. Pharmaceuticals labelled with stable isotopes

    International Nuclear Information System (INIS)

    Krumbiegel, P.

    1986-11-01

    The relatively new field of pharmaceuticals labelled with stable isotopes is reviewed. Scientific, juridical, and ethical questions are discussed concerning the application of these pharmaceuticals in human medicine. 13 C, 15 N, and 2 H are the stable isotopes mainly utilized in metabolic function tests. Methodical contributions are given to the application of 2 H, 13 C, and 15 N pharmaceuticals showing new aspects and different states of development in the field under discussion. (author)

  12. Radioactively labelled vitamin B12

    International Nuclear Information System (INIS)

    Charlton, J.C.; Lewis, A.

    1976-01-01

    A method is described for preparing radioactively labelled vitamin B 12 (cyanocobalamin) by reacting α-(5,6-dimethylbenzimidazolyl) hydrogenobamide with active (sup(57,58)Co) cobaltous ion. The latter may be in the form of cobaltous chloride or sulphate in aqueous or aqueous alcoholic medium. The reaction is effected by heating the reactants in darkness at pH 4 to 8. An excess of cyanide is added to convert the hydroxocobalamin formed to cyanocobalamin. (U.K.)

  13. Synthesis of deuterium labelled ibuprofen

    International Nuclear Information System (INIS)

    Cappon, V.J.; Halstead, G.W.; Theis, D.L.

    1986-01-01

    The preparations of [ar- 2 H 4 ]-ibuprofen and [ar, 3,3,3- 2 H 7 ]-ibuprofen are described. The deuterium was incorporated into the aromatic ring of [ar- 2 H 4 ]-ibuprofen which is a metabolically stable position. [ar, 3,3,3- 2 H 7 ]-ibuprofen was synthesized by the same route using [ 2 H 3 ]-CH 3 I instead of CH 3 I for use as a GC/MS internal standard in stable isotope labelled bioavailability studies. (author)

  14. Benchmark assemblies of the Los Alamos Critical Assemblies Facility

    International Nuclear Information System (INIS)

    Dowdy, E.J.

    1985-01-01

    Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described

  15. Benchmark assemblies of the Los Alamos critical assemblies facility

    International Nuclear Information System (INIS)

    Dowdy, E.J.

    1985-01-01

    Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described

  16. Benchmark assemblies of the Los Alamos critical assemblies facility

    International Nuclear Information System (INIS)

    Dowdy, E.J.

    1986-01-01

    Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described. (author)

  17. Peptide amphiphile self-assembly

    Science.gov (United States)

    Iscen, Aysenur; Schatz, George C.

    2017-08-01

    Self-assembly is a process whereby molecules organize into structures with hierarchical order and complexity, often leading to functional materials. Biomolecules such as peptides, lipids and DNA are frequently involved in self-assembly, and this leads to materials of interest for a wide variety of applications in biomedicine, photonics, electronics, mechanics, etc. The diversity of structures and functions that can be produced provides motivation for developing theoretical models that can be used for a molecular-level description of these materials. Here we overview recently developed computational methods for modeling the self-assembly of peptide amphiphiles (PA) into supramolecular structures that form cylindrical nanoscale fibers using molecular-dynamics simulations. Both all-atom and coarse-grained force field methods are described, and we emphasize how these calculations contribute insight into fiber structure, including the importance of β-sheet formation. We show that the temperature at which self-assembly takes place affects the conformations of PA chains, resulting in cylindrical nanofibers with higher β-sheet content as temperature increases. We also present a new high-density PA model that shows long network formation of β-sheets along the long axis of the fiber, a result that correlates with some experiments. The β-sheet network is mostly helical in nature which helps to maintain strong interactions between the PAs both radially and longitudinally. Contribution to Focus Issue Self-assemblies of Inorganic and Organic Nanomaterials edited by Marie-Paule Pileni.

  18. Inverse design of multicomponent assemblies

    Science.gov (United States)

    Piñeros, William D.; Lindquist, Beth A.; Jadrich, Ryan B.; Truskett, Thomas M.

    2018-03-01

    Inverse design can be a useful strategy for discovering interactions that drive particles to spontaneously self-assemble into a desired structure. Here, we extend an inverse design methodology—relative entropy optimization—to determine isotropic interactions that promote assembly of targeted multicomponent phases, and we apply this extension to design interactions for a variety of binary crystals ranging from compact triangular and square architectures to highly open structures with dodecagonal and octadecagonal motifs. We compare the resulting optimized (self- and cross) interactions for the binary assemblies to those obtained from optimization of analogous single-component systems. This comparison reveals that self-interactions act as a "primer" to position particles at approximately correct coordination shell distances, while cross interactions act as the "binder" that refines and locks the system into the desired configuration. For simpler binary targets, it is possible to successfully design self-assembling systems while restricting one of these interaction types to be a hard-core-like potential. However, optimization of both self- and cross interaction types appears necessary to design for assembly of more complex or open structures.

  19. Container for spent fuel assembly

    International Nuclear Information System (INIS)

    Sawai, Takeshi.

    1996-01-01

    The container of the present invention comprises a container main body having a body portion which can contain spent fuel assemblies and a lid, and heat pipes having an evaporation portion disposed along the outer surface of the spent fuel assemblies to be contained and a condensation portion exposed to the outside of the container main body. Further, the heat pipe is formed spirally at the evaporation portions so as to surround the outer circumference of the spent fuel assemblies, branched into a plurality of portions at the condensation portion, each of the branched portion of the condensation portion being exposed to the outside of the container main body, and is tightly in contact with the periphery of the slit portions disposed to the container main body. Then, since released after heat is transferred to the outside of the container main body from the evaporation portion of the heat pipe along the outer surface of the spent fuel assemblies by way of the condensation portion of the heat pipes exposed to the outside of the container main body, the efficiency of the heat transfer is extremely improved to enhance the effect of removing heat of spent fuel assemblies. Further, cooling effect is enhanced by the spiral form of the evaporation portion and the branched condensation portion. (N.H.)

  20. Nutrition marketing on food labels.

    Science.gov (United States)

    Colby, Sarah E; Johnson, LuAnn; Scheett, Angela; Hoverson, Bonita

    2010-01-01

    This research sought to determine how often nutrition marketing is used on labels of foods that are high in saturated fat, sodium, and/or sugar. All items packaged with food labels (N = 56,900) in all 6 grocery stores in Grand Forks, ND were surveyed. Marketing strategy, nutrient label information, if the product was fruit/or milk based, and target age. Frequency distributions were computed. Forty-nine percent of all products contained nutrition marketing and of those, 48% had both nutrition marketing and were high in saturated fat, sodium and/or sugar (11%, 17%, and 31% respectively). Seventy-one percent of products marketed to children had nutrition marketing. Of those, 59% were high in saturated fat, sodium and/or sugar content, with more than half being high in sugar. The most commonly used nutrition marketing statements were "good source of calcium", "reduced/low/fat free", and "food company's health symbol". Nutrition marketing is commonly used on products high in saturated fat, sodium and/or sugar and is more often used on products marketed toward children than products marketed toward adults. Current food industry symbols may not be helping consumers select foods low in saturated fat, sodium or sugar. Published by Elsevier Inc.

  1. Isotopically labelled pyrimidines and purines

    International Nuclear Information System (INIS)

    Balaban, A.T.; Bally, I.

    1987-01-01

    Among the three diazines, pyrimidine is by far the most important one because its derivatives uracil, thymine and cytosine are constituents of the ubiquitous deoxynucleic acids (DNA) and ribonucleic acids (RNA). Other derivatives of pyrimidine without condensed rings include barbiturates, alloxan, orotic acid and thiamine or vitamin B 1 . From the polycyclic derivatives of pyrimidine such as pteridine, alloxazine, and purine, the latter, through its derivatives adenine and guanine complete the list of bases which occur in DNA and RNA: in addition, other purine derivatives such as hypoxanthine, xanthine, theobromine, theophylline, caffeine and uric acid are important natural products with biological activity. The paper presents methods for preparing isotopically labeled pyrimidines as well as purine derivatives. For convenience, the authors describe separately carbon-labeled with radioisotopes 11 C (T 1/2 = 20.3 min) and 14 C (T 1/2 = 5736 years) or the stable isotope 13 C (natural abundance 1.1%) and then hydrogen-labeled systems with the radioisotope 3 H ≡ T (T 1/2 = 12.346 years) or with the stable isotope 2 H ≡ D (natural abundance 0.015%). We do not separate stable from radioactive isotopes because the synthetic methods are identical for the same element; however, the introduction of hydrogen isotopes into organic molecules is often performed by reactions such as isotope exchange which cannot take place in the case of carbon isotopes

  2. Gender, status, and psychiatric labels.

    Science.gov (United States)

    Kroska, Amy; Harkness, Sarah K; Brown, Ryan P; Thomas, Lauren S

    2015-11-01

    We examine a key modified labeling theory proposition-that a psychiatric label increases vulnerability to competence-based criticism and rejection-within task- and collectively oriented dyads comprised of same-sex individuals with equivalent education. Drawing on empirical work that approximates these conditions, we expect the proposition to hold only among men. We also expect education, operationalized with college class standing, to moderate the effects of gender by reducing men's and increasing women's criticism and rejection. But, we also expect the effect of education to weaken when men work with a psychiatric patient. As predicted, men reject suggestions from teammates with a psychiatric history more frequently than they reject suggestions from other teammates, while women's resistance to influence is unaffected by their teammate's psychiatric status. Men also rate psychiatric patient teammates as less powerful but no lower in status than other teammates, while women's teammate assessments are unaffected by their teammate's psychiatric status. Also as predicted, education reduces men's resistance to influence when their teammate has no psychiatric history. Education also increases men's ratings of their teammate's power, as predicted, but has no effect on women's resistance to influence or teammate ratings. We discuss the implications of these findings for the modified labeling theory of mental illness and status characteristics theory. Copyright © 2015 Elsevier Inc. All rights reserved.

  3. Stigma of a label: educational expectations for high school students labeled with learning disabilities.

    Science.gov (United States)

    Shifrer, Dara

    2013-01-01

    Poorer outcomes for youth labeled with learning disabilities (LDs) are often attributed to the student's own deficiencies or cumulative disadvantage; but the more troubling possibility is that special education placement limits rather than expands these students' opportunities. Labeling theory partially attributes the poorer outcomes of labeled persons to stigma related to labels. This study uses data on approximately 11,740 adolescents and their schools from the Education Longitudinal Survey of 2002 to determine if stigma influences teachers' and parents' educational expectations for students labeled with LDs and labeled adolescents' expectations for themselves. Supporting the predictions of labeling theory, teachers and parents are more likely to perceive disabilities in, and hold lower educational expectations for labeled adolescents than for similarly achieving and behaving adolescents not labeled with disabilities. The negative effect of being labeled with LDs on adolescents' educational expectations is partially mechanized through parents' and particularly teachers' lower expectations.

  4. Workload analyse of assembling process

    Science.gov (United States)

    Ghenghea, L. D.

    2015-11-01

    The workload is the most important indicator for managers responsible of industrial technological processes no matter if these are automated, mechanized or simply manual in each case, machines or workers will be in the focus of workload measurements. The paper deals with workload analyses made to a most part manual assembling technology for roller bearings assembling process, executed in a big company, with integrated bearings manufacturing processes. In this analyses the delay sample technique have been used to identify and divide all bearing assemblers activities, to get information about time parts from 480 minutes day work time that workers allow to each activity. The developed study shows some ways to increase the process productivity without supplementary investments and also indicated the process automation could be the solution to gain maximum productivity.

  5. Fixture for aligning motor assembly

    Science.gov (United States)

    Shervington, Roger M.; Vaghani, Vallabh V.; Vanek, Laurence D.; Christensen, Scott A.

    2009-12-08

    An alignment fixture includes a rotor fixture, a stator fixture and a sensor system which measures a rotational displacement therebetween. The fixture precisely measures rotation of a generator stator assembly away from a NULL position referenced by a unique reference spline on the rotor shaft. By providing an adjustable location of the stator assembly within the housing, the magnetic axes within each generator shall be aligned to a predetermined and controlled tolerance between the generator interface mounting pin and the reference spline on the rotor shaft. Once magnetically aligned, each generator is essentially a line replaceable unit which may be readily mounted to any input of a multi-generator gearbox assembly with the assurance that the magnetic alignment will be within a predetermined tolerance.

  6. Types for DSP Assembler Programs

    DEFF Research Database (Denmark)

    Larsen, Ken

    2006-01-01

    for reuse, and a procedure that computes point-wise vector multiplication. The latter uses a common idiom of prefetching memory resulting in out-of-bounds reading from memory. I present two extensions to the baseline type system: The first extension is a simple modification of some type rules to allow out......-ofbounds reading from memory. The second extension is based on two major modifications of the baseline type system: • Abandoning the type-invariance principle of memory locations and using a variation of alias types instead. • Introducing aggregate types, making it possible to have different views of a block...... in assembler language. However, programming in assembler causes numerous problems, such as memory corruption, for instance. To test the thesis I define a model assembler language called Featherweight DSP which captures some of the essential features of a real custom DSP used in the industrial partner's digital...

  7. FUEL ASSEMBLY SHAKER TEST SIMULATION

    Energy Technology Data Exchange (ETDEWEB)

    Klymyshyn, Nicholas A.; Sanborn, Scott E.; Adkins, Harold E.; Hanson, Brady D.

    2013-05-30

    This report describes the modeling of a PWR fuel assembly under dynamic shock loading in support of the Sandia National Laboratories (SNL) shaker test campaign. The focus of the test campaign is on evaluating the response of used fuel to shock and vibration loads that a can occur during highway transport. Modeling began in 2012 using an LS-DYNA fuel assembly model that was first created for modeling impact scenarios. SNL’s proposed test scenario was simulated through analysis and the calculated results helped guide the instrumentation and other aspects of the testing. During FY 2013, the fuel assembly model was refined to better represent the test surrogate. Analysis of the proposed loads suggested the frequency band needed to be lowered to attempt to excite the lower natural frequencies of the fuel assembly. Despite SNL’s expansion of lower frequency components in their five shock realizations, pretest predictions suggested a very mild dynamic response to the test loading. After testing was completed, one specific shock case was modeled, using recorded accelerometer data to excite the model. Direct comparison of predicted strain in the cladding was made to the recorded strain gauge data. The magnitude of both sets of strain (calculated and recorded) are very low, compared to the expected yield strength of the Zircaloy-4 material. The model was accurate enough to predict that no yielding of the cladding was expected, but its precision at predicting micro strains is questionable. The SNL test data offers some opportunity for validation of the finite element model, but the specific loading conditions of the testing only excite the fuel assembly to respond in a limited manner. For example, the test accelerations were not strong enough to substantially drive the fuel assembly out of contact with the basket. Under this test scenario, the fuel assembly model does a reasonable job of approximating actual fuel assembly response, a claim that can be verified through

  8. Assembly and Dynamics of Myofibrils

    Directory of Open Access Journals (Sweden)

    Joseph W. Sanger

    2010-01-01

    Full Text Available We review some of the problems in determining how myofibrils may be assembled and just as importantly how this contractile structure may be renewed by sarcomeric proteins moving between the sarcomere and the cytoplasm. We also address in this personal review the recent evidence that indicates that the assembly and dynamics of myofibrils are conserved whether the cells are analyzed in situ or in tissue culture conditions. We suggest that myofibrillogenesis is a fundamentally conserved process, comparable to protein synthesis, mitosis, or cytokinesis, whether examined in situ or in vitro.

  9. DNA-guided nanoparticle assemblies

    Science.gov (United States)

    Gang, Oleg; Nykypanchuk, Dmytro; Maye, Mathew; van der Lelie, Daniel

    2013-07-16

    In some embodiments, DNA-capped nanoparticles are used to define a degree of crystalline order in assemblies thereof. In some embodiments, thermodynamically reversible and stable body-centered cubic (bcc) structures, with particles occupying <.about.10% of the unit cell, are formed. Designs and pathways amenable to the crystallization of particle assemblies are identified. In some embodiments, a plasmonic crystal is provided. In some aspects, a method for controlling the properties of particle assemblages is provided. In some embodiments a catalyst is formed from nanoparticles linked by nucleic acid sequences and forming an open crystal structure with catalytically active agents attached to the crystal on its surface or in interstices.

  10. Self-assembly of self-assembled molecular triangles

    Indian Academy of Sciences (India)

    (tmeda), 2,2 -bipyridine (bpy), and 1,10-phenanthroline. (phen), etc. The synthesis and dynamic studies of a vari- ety of designed Pd(II) cages are well studied1a−d but the crystal engineering of Pd(II)-based self-assembled coordination cages has been less explored.4 Recently we have been investigating the significance of ...

  11. Flow resistance in rod assemblies

    International Nuclear Information System (INIS)

    Korsun, A.S.; Sokolova, M.S.

    2000-01-01

    The general form of relation between the resistance force and the velocity vector, resistance tensor structure and possible types of anisotropy in the flow thorough such structures as rod or tube assemblies are under discussion. Some questions of experimental determination of volumetric resistance force tensor are also under consideration. (author)

  12. Flanged major modular assembly jig

    Science.gov (United States)

    Gilman, M. M. (Inventor)

    1976-01-01

    Weldless methods and means are described for securing flanges to the projecting ends of an unmachined box beam framework in such a manner that the flanged structure may be reused without modification. And one framework may be readily assembled to another by simply matching the flanges together and passing connecting members between performed holes in the structures.

  13. Radial blanket assembly orificing arrangement

    Science.gov (United States)

    Patterson, J.F.

    1975-07-01

    A nuclear reactor core for a liquid metal cooled fast breeder reactor is described in which means are provided for increasing the coolant flow through the reactor fuel assemblies as the reactor ages by varying the coolant flow rate with the changing coolant requirements during the core operating lifetime. (auth)

  14. In vitro assembly of catalase.

    Science.gov (United States)

    Baureder, Michael; Barane, Elisabeth; Hederstedt, Lars

    2014-10-10

    Most aerobic organisms contain catalase, which functions to decompose hydrogen peroxide. Typical catalases are structurally complex homo-tetrameric enzymes with one heme prosthetic group buried in each subunit. It is not known how catalase in the cell is assembled from its constituents. The bacterium Enterococcus faecalis cannot synthesize heme but can acquire it from the environment to form a cytoplasmic catalase. We have in E. faecalis monitored production of the enzyme polypeptide (KatA) depending on the availability of heme and used our findings to devise a procedure for the purification of preparative amounts of in vivo-synthesized apocatalase. We show that fully active catalase can be obtained in vitro by incubating isolated apoprotein with hemin. We have characterized features of the assembly process and describe a temperature-trapped hemylated intermediate of the enzyme maturation process. Hemylation of apocatalase does not require auxiliary cell components, but rapid assembly of active enzyme seemingly is assisted in the cell. Our findings provide insight about catalase assembly and offer new experimental possibilities for detailed studies of this process. © 2014 by The American Society for Biochemistry and Molecular Biology, Inc.

  15. STAGE MODEL FOR GONDWANA ASSEMBLY

    African Journals Online (AJOL)

    and the Kalahari craton (IMSLEK terranes) with the Congo craton and the Arabian Nubian Shield (ANS). The younger granulite event recorded in the Kitumbi area could then mark a younger collision between Australo-Antarctica and the combined IMSLEK-Conga. ANS collage marking the final assembly of Gondwana.

  16. Simulated nuclear reactor fuel assembly

    International Nuclear Information System (INIS)

    Berta, V.T.

    1993-01-01

    An apparatus for electrically simulating a nuclear reactor fuel assembly. It includes a heater assembly having a top end and a bottom end and a plurality of concentric heater tubes having electrical circuitry connected to a power source, and radially spaced from each other. An outer target tube and an inner target tube is concentric with the heater tubes and with each other, and the outer target tube surrounds and is radially spaced from the heater tubes. The inner target tube is surrounded by and radially spaced from the heater tubes and outer target tube. The top of the assembly is generally open to allow for the electrical power connection to the heater tubes, and the bottom of the assembly includes means for completing the electrical circuitry in the heater tubes to provide electrical resistance heating to simulate the power profile in a nuclear reactor. The embedded conductor elements in each heater tube is split into two halves for a substantial portion of its length and provided with electrical isolation such that each half of the conductor is joined at one end and is not joined at the other end

  17. In Vitro Assembly of Catalase*

    Science.gov (United States)

    Baureder, Michael; Barane, Elisabeth; Hederstedt, Lars

    2014-01-01

    Most aerobic organisms contain catalase, which functions to decompose hydrogen peroxide. Typical catalases are structurally complex homo-tetrameric enzymes with one heme prosthetic group buried in each subunit. It is not known how catalase in the cell is assembled from its constituents. The bacterium Enterococcus faecalis cannot synthesize heme but can acquire it from the environment to form a cytoplasmic catalase. We have in E. faecalis monitored production of the enzyme polypeptide (KatA) depending on the availability of heme and used our findings to devise a procedure for the purification of preparative amounts of in vivo-synthesized apocatalase. We show that fully active catalase can be obtained in vitro by incubating isolated apoprotein with hemin. We have characterized features of the assembly process and describe a temperature-trapped hemylated intermediate of the enzyme maturation process. Hemylation of apocatalase does not require auxiliary cell components, but rapid assembly of active enzyme seemingly is assisted in the cell. Our findings provide insight about catalase assembly and offer new experimental possibilities for detailed studies of this process. PMID:25148685

  18. Self-assembly of cyclodextrins

    DEFF Research Database (Denmark)

    Fülöp, Z.; Kurkov, S.V.; Nielsen, T.T.

    2012-01-01

    that increases upon formation of inclusion complexes with lipophilic drugs. However, the stability of such aggregates is not sufficient for parenteral administration. In this review CD polymers and CD containing nanoparticles are categorized, with focus on self-assembled CD nanoparticles. It is described how...

  19. Vibration Damping Circuit Card Assembly

    Science.gov (United States)

    Hunt, Ronald Allen (Inventor)

    2016-01-01

    A vibration damping circuit card assembly includes a populated circuit card having a mass M. A closed metal container is coupled to a surface of the populated circuit card at approximately a geometric center of the populated circuit card. Tungsten balls fill approximately 90% of the metal container with a collective mass of the tungsten balls being approximately (0.07) M.

  20. Dynamics of assembly production flow

    Science.gov (United States)

    Ezaki, Takahiro; Yanagisawa, Daichi; Nishinari, Katsuhiro

    2015-06-01

    Despite recent developments in management theory, maintaining a manufacturing schedule remains difficult because of production delays and fluctuations in demand and supply of materials. The response of manufacturing systems to such disruptions to dynamic behavior has been rarely studied. To capture these responses, we investigate a process that models the assembly of parts into end products. The complete assembly process is represented by a directed tree, where the smallest parts are injected at leaves and the end products are removed at the root. A discrete assembly process, represented by a node on the network, integrates parts, which are then sent to the next downstream node as a single part. The model exhibits some intriguing phenomena, including overstock cascade, phase transition in terms of demand and supply fluctuations, nonmonotonic distribution of stockout in the network, and the formation of a stockout path and stockout chains. Surprisingly, these rich phenomena result from only the nature of distributed assembly processes. From a physical perspective, these phenomena provide insight into delay dynamics and inventory distributions in large-scale manufacturing systems.

  1. Monolithic fiber optic sensor assembly

    Science.gov (United States)

    Sanders, Scott

    2015-02-10

    A remote sensor element for spectrographic measurements employs a monolithic assembly of one or two fiber optics to two optical elements separated by a supporting structure to allow the flow of gases or particulates therebetween. In a preferred embodiment, the sensor element components are fused ceramic to resist high temperatures and failure from large temperature changes.

  2. Fuel assemblies for nuclear reactor

    International Nuclear Information System (INIS)

    Nishi, Akihito.

    1987-01-01

    Purpose: To control power-up rate at the initial burning stage of new fuel assemblies due to fuel exchange in a pressure tube type power reactor. Constitution: Burnable poisons are disposed to a most portion of fuel pellets in a fuel assembly to such a low concentration as the burn-up rate changes with time at the initial stage of the burning. The most portion means substantially more than one-half part of the pellets and gadolinia is used as burn-up poisons to be dispersed and the concentration is set to less than about 0.2 %. Upon elapse of about 15 days after the charging, the burnable poisons are eliminated and the infinite multiplication factors are about at 1.2 to attain a predetermined power state. Since the power-up rate of the nuclear reactor fuel assembly is about 0.1 % power/hour and the power-up rate of the fuel assembly around the exchanged channel is lower than that, it can be lowered sufficiently than the limit for the power-up rate practiced upon reactor start-up thereby enabling to replace fuels during power operation. (Horiuchi, T.)

  3. ATLAS Assembly Hall Open Day

    CERN Multimedia

    Patrice Loiez

    2004-01-01

    To mark the 50th Anniversary of the founding of CERN, a day of tours, displays and presentations was held in October 2004. The assembly halls for the experiments that were waiting to be installed on the LHC, such as ATLAS shown here, were transformed into display areas and cafés.

  4. Tritium labeling of detonation nanodiamonds.

    Science.gov (United States)

    Girard, Hugues A; El-Kharbachi, Abdelouahab; Garcia-Argote, Sébastien; Petit, Tristan; Bergonzo, Philippe; Rousseau, Bernard; Arnault, Jean-Charles

    2014-03-18

    For the first time, the radioactive labeling of detonation nanodiamonds was efficiently achieved using a tritium microwave plasma. According to our measurements, the total radioactivity reaches 9120 ± 120 μCi mg(-1), with 93% of (3)H atoms tightly bonded to the surface and up to 7% embedded into the diamond core. Such (3)H doping will ensure highly stable radiolabeled nanodiamonds, on which surface functionalization is still allowed. This breakthrough opens the way to biodistribution and pharmacokinetics studies of nanodiamonds, while this approach can be scalable to easily treat bulk quantities of nanodiamonds at low cost.

  5. Hemoglobin Labeled by Radioactive Lysine

    Science.gov (United States)

    Bale, W. F.; Yuile, C. L.; DeLaVergne, L.; Miller, L. L.; Whipple, G. H.

    1949-12-08

    This paper reports on the utilization of tagged epsilon carbon of DL-lysine by a dog both anemic and hypoproteinemic due to repeated bleeding plus a diet low in protein. The experiment extended over period of 234 days, a time sufficient to indicate an erythrocyte life span of at least 115 days based upon the rate of replacement of labeled red cell proteins. The proteins of broken down red cells seem not to be used with any great preference for the synthesis of new hemoglobin.

  6. Multi-Robot Assembly Strategies and Metrics

    Science.gov (United States)

    MARVEL, JEREMY A.; BOSTELMAN, ROGER; FALCO, JOE

    2018-01-01

    We present a survey of multi-robot assembly applications and methods and describe trends and general insights into the multi-robot assembly problem for industrial applications. We focus on fixtureless assembly strategies featuring two or more robotic systems. Such robotic systems include industrial robot arms, dexterous robotic hands, and autonomous mobile platforms, such as automated guided vehicles. In this survey, we identify the types of assemblies that are enabled by utilizing multiple robots, the algorithms that synchronize the motions of the robots to complete the assembly operations, and the metrics used to assess the quality and performance of the assemblies. PMID:29497234

  7. Multi-Robot Assembly Strategies and Metrics.

    Science.gov (United States)

    Marvel, Jeremy A; Bostelman, Roger; Falco, Joe

    2018-02-01

    We present a survey of multi-robot assembly applications and methods and describe trends and general insights into the multi-robot assembly problem for industrial applications. We focus on fixtureless assembly strategies featuring two or more robotic systems. Such robotic systems include industrial robot arms, dexterous robotic hands, and autonomous mobile platforms, such as automated guided vehicles. In this survey, we identify the types of assemblies that are enabled by utilizing multiple robots, the algorithms that synchronize the motions of the robots to complete the assembly operations, and the metrics used to assess the quality and performance of the assemblies.

  8. Label-free DNA biosensor based on resistance change of platinum nanoparticles assemblies.

    Science.gov (United States)

    Skotadis, Evangelos; Voutyras, Konstantinos; Chatzipetrou, Marianneza; Tsekenis, Georgios; Patsiouras, Lampros; Madianos, Leonidas; Chatzandroulis, Stavros; Zergioti, Ioanna; Tsoukalas, Dimitris

    2016-07-15

    A novel nanoparticle based biosensor for the fast and simple detection of DNA hybridization events is presented. The sensor utilizes hybridized DNA's charge transport properties, combining them with metallic nanoparticle networks that act as nano-gapped electrodes. The DNA hybridization events can be detected by a significant reduction in the sensor's resistance due to the conductive bridging offered by hybridized DNA. By modifying the nanoparticle surface coverage, which can be controlled experimentally being a function of deposition time, and the structural properties of the electrodes, an optimized biosensor for the in situ detection of DNA hybridization events is ultimately fabricated. The fabricated biosensor exhibits a wide response range, covering four orders of magnitude, a limit of detection of 1nM and can detect a single base pair mismatch between probe and complementary DNA. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Label Space Reduction in MPLS Networks: How Much Can A Single Stacked Label Do?

    DEFF Research Database (Denmark)

    Solano, Fernando; Stidsen, Thomas K.; Fabregat, Ramon

    2008-01-01

    Most network operators have considered reducing LSR label spaces (number of labels used) as a way of simplifying management of underlaying virtual private networks (VPNs) and therefore reducing operational expenditure (OPEX). The IETF outlined the label merging feature in MPLS-allowing the config......Most network operators have considered reducing LSR label spaces (number of labels used) as a way of simplifying management of underlaying virtual private networks (VPNs) and therefore reducing operational expenditure (OPEX). The IETF outlined the label merging feature in MPLS...

  10. In-capillary self-assembly and proteolytic cleavage of polyhistidine peptide capped quantum dots

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jianhao; Li, Jingyan; Li, Jinchen; Liu, Feifei [School of Pharmaceutical Engineering and Life Science, Changzhou University, Changzhou, Jiangsu, 213164 (China); Zhou, Xiang; Yao, Yi [Changzhou Qianhong Bio-pharma Co. Ltd, Changzhou 213164, Jiangsu (China); Wang, Cheli [School of Pharmaceutical Engineering and Life Science, Changzhou University, Changzhou, Jiangsu, 213164 (China); Qiu, Lin, E-mail: linqiupjj@gmail.com [School of Pharmaceutical Engineering and Life Science, Changzhou University, Changzhou, Jiangsu, 213164 (China); Jiang, Pengju, E-mail: pengju.jiang@gmail.com [School of Pharmaceutical Engineering and Life Science, Changzhou University, Changzhou, Jiangsu, 213164 (China); State Key Laboratory of Pharmaceutical Biotechnology, Nanjing, Jiangsu (China)

    2015-10-01

    A new method using fluorescence coupled capillary electrophoresis (CE-FL) for monitoring self-assembly and proteolytic cleavage of hexahistidine peptide capped quantum dots (QDs) inside a capillary has been developed in this report. QDs and the ATTO 590-labeled hexahistidine peptide (H6-ATTO) were injected into a capillary, sequentially. Their self-assembly inside the capillary was driven by a metal-affinity force which yielded a new fluorescence signal due to Förster resonance energy transfer (FRET). The highly efficient separation of fluorescent complexes and the FRET process were analyzed using CE-FL. The self-assembly of QDs and biomolecules was found to effectively take place inside the capillary. The kinetics of the assembly was monitored by CE-FL, and the approach was extended to the study of proteolytic cleavage of surface conjugated peptides. Being the first in-depth analysis of in-capillary nanoparticle–biomolecule assembly, the novel approach reported here provides inspiration to the development of QD-based FRET probes for biomedical applications. - Highlights: • We examined the self-assembly QDs with H6-ATTO inside a capillary. • We prove CE-FL to be a powerful method to resolve QDs-H6-ATTO complex. • We achieve chromatographic separation of QDs-H6-ATTO complex. • We discovered a novel strategy for the online detection of thrombin. • This technique integrated “injection, mixing, reaction, separation and detection”.

  11. Chain-Length Heterogeneity Allows for the Assembly of Fatty Acid Vesicles in Dilute Solutions

    Science.gov (United States)

    Budin, Itay; Prwyes, Noam; Zhang, Na; Szostak, Jack W.

    2014-01-01

    A requirement for concentrated and chemically homogeneous pools of molecular building blocks would severely restrict plausible scenarios for the origin of life. In the case of membrane self-assembly, models of prebiotic lipid synthesis yield primarily short, single-chain amphiphiles that can form bilayer vesicles only at very high concentrations. These high critical aggregation concentrations (cacs) pose significant obstacles for the self-assembly of single-chain lipid membranes. Here, we examine membrane self-assembly in mixtures of fatty acids with varying chain lengths, an expected feature of any abiotic lipid synthesis. We derive theoretical predictions for the cac of mixtures by adapting thermodynamic models developed for the analogous phenomenon of mixed micelle self-assembly. We then use several complementary methods to characterize aggregation experimentally, and find cac values in close agreement with our theoretical predictions. These measurements establish that the cac of fatty acid mixtures is dramatically lowered by minor fractions of long-chain species, thereby providing a plausible route for protocell membrane assembly. Using an NMR-based approach to monitor aggregation of isotopically labeled samples, we demonstrate the incorporation of individual components into mixed vesicles. These experiments suggest that vesicles assembled in dilute, mixed solutions are depleted of the shorter-chain-length lipid species, a finding that carries implications for the composition of primitive cell membranes. PMID:25296310

  12. Link Label Prediction in Signed Citation Network

    KAUST Repository

    Akujuobi, Uchenna

    2016-04-12

    Link label prediction is the problem of predicting the missing labels or signs of all the unlabeled edges in a network. For signed networks, these labels can either be positive or negative. In recent years, different algorithms have been proposed such as using regression, trust propagation and matrix factorization. These approaches have tried to solve the problem of link label prediction by using ideas from social theories, where most of them predict a single missing label given that labels of other edges are known. However, in most real-world social graphs, the number of labeled edges is usually less than that of unlabeled edges. Therefore, predicting a single edge label at a time would require multiple runs and is more computationally demanding. In this thesis, we look at link label prediction problem on a signed citation network with missing edge labels. Our citation network consists of papers from three major machine learning and data mining conferences together with their references, and edges showing the relationship between them. An edge in our network is labeled either positive (dataset relevant) if the reference is based on the dataset used in the paper or negative otherwise. We present three approaches to predict the missing labels. The first approach converts the label prediction problem into a standard classification problem. We then, generate a set of features for each edge and then adopt Support Vector Machines in solving the classification problem. For the second approach, we formalize the graph such that the edges are represented as nodes with links showing similarities between them. We then adopt a label propagation method to propagate the labels on known nodes to those with unknown labels. In the third approach, we adopt a PageRank approach where we rank the nodes according to the number of incoming positive and negative edges, after which we set a threshold. Based on the ranks, we can infer an edge would be positive if it goes a node above the

  13. Label-free photoacoustic nanoscopy

    Science.gov (United States)

    Danielli, Amos; Maslov, Konstantin; Garcia-Uribe, Alejandro; Winkler, Amy M.; Li, Chiye; Wang, Lidai; Chen, Yun; Dorn, Gerald W.; Wang, Lihong V.

    2014-08-01

    Super-resolution microscopy techniques-capable of overcoming the diffraction limit of light-have opened new opportunities to explore subcellular structures and dynamics not resolvable in conventional far-field microscopy. However, relying on staining with exogenous fluorescent markers, these techniques can sometimes introduce undesired artifacts to the image, mainly due to large tagging agent sizes and insufficient or variable labeling densities. By contrast, the use of endogenous pigments allows imaging of the intrinsic structures of biological samples with unaltered molecular constituents. Here, we report label-free photoacoustic (PA) nanoscopy, which is exquisitely sensitive to optical absorption, with an 88 nm resolution. At each scanning position, multiple PA signals are successively excited with increasing laser pulse energy. Because of optical saturation or nonlinear thermal expansion, the PA amplitude depends on the nonlinear incident optical fluence. The high-order dependence, quantified by polynomial fitting, provides super-resolution imaging with optical sectioning. PA nanoscopy is capable of super-resolution imaging of either fluorescent or nonfluorescent molecules.

  14. Multimodal label-free microscopy

    Directory of Open Access Journals (Sweden)

    Nicolas Pavillon

    2014-09-01

    Full Text Available This paper reviews the different multimodal applications based on a large extent of label-free imaging modalities, ranging from linear to nonlinear optics, while also including spectroscopic measurements. We put specific emphasis on multimodal measurements going across the usual boundaries between imaging modalities, whereas most multimodal platforms combine techniques based on similar light interactions or similar hardware implementations. In this review, we limit the scope to focus on applications for biology such as live cells or tissues, since by their nature of being alive or fragile, we are often not free to take liberties with the image acquisition times and are forced to gather the maximum amount of information possible at one time. For such samples, imaging by a given label-free method usually presents a challenge in obtaining sufficient optical signal or is limited in terms of the types of observable targets. Multimodal imaging is then particularly attractive for these samples in order to maximize the amount of measured information. While multimodal imaging is always useful in the sense of acquiring additional information from additional modes, at times it is possible to attain information that could not be discovered using any single mode alone, which is the essence of the progress that is possible using a multimodal approach.

  15. Assembly, component for an assembly and method of manufacturing in assembly

    NARCIS (Netherlands)

    Kok, M.M. de; Brand, J. van den; Heck, G.T. van

    2011-01-01

    An assembly of a plurality of tiles (1) with a carrier (40), wherein the tiles (1) comprise a foil (20) with an electro-physical transducer (10) and electrical connectors (24, 28) to said transducer. The tiles are mechanically and electrically coupled to the carrier, and the tiles overlay according

  16. Radiopharmaceutical potential of I-131 labelled diazepam

    International Nuclear Information System (INIS)

    Yurt, F.; Unek, P.; Asikoglu, M.; Baggi, S.; Erener, G.; Ozkilic, H.; Uluc, F.; Tuglular, I.

    1998-01-01

    In this study, diazepam is a derivative of the 1.4 benzodiazepine family that the most widely used drug as anticonvulsant agent has been labeled with I-131, as a new radiopharmaceutical and its radiopharmaceutical potential has been determined. Labeling of diazepam has been performed by iodogen method and optimum labeling conditions have been determined. Optimum reaction conditions are 1 mg for iodogen amount; 1-5 mg for diazepam amount, 15-20 minutes for reaction time and room temperature for reaction temperature. Specific activity of labeled compound was 0,15 Ci/mmol level. N-octanol/water ratio was found 1.9 for 131 IDZ ( 131 I labeled diazepam). In vivo experiments have been carried out to determine radiopharmaceutical potentials of labeled compound. Biodistribution studies on rats showed that 131 IDZ have accumulated in kidneys, liver, lungs and brain tissues. Scintigraphic results taken with gamma camera on rabbits agree with biodistribution results of rats. (author)

  17. Chemoenzymatic synthesis of carbon-14 labelled antioxidants

    International Nuclear Information System (INIS)

    Deigner, H.P.; Freyberg, C.; Heck, R.

    1993-01-01

    The syntheses of [ 14 C] labelled antioxidants are described. We developed an efficient synthetic methodology to prepare a series of labelled amides with antioxidant activity, starting from [ 14 C] KCN and alkyl or aryl halides. By a combination of nucleophilic displacement of halides by [ 14 C] cyanide, mediated by ultrasound and subsequent mild and selective enzymatic hydrolysis of the resulting nitriles, labelled carboxylic acids were obtained. Labelled amines were prepared by reduction of the respective nitriles. Availability of [ 14 C] KCN, efficient introduction of the label by ultrasound mediated reaction and selective and mild hydrolysis by commercially available nitrilase (Rhodococcus sp.), makes possible a wide range of applications of this methodology in the synthesis of functionalized labelled compounds. (Author)

  18. Molecular Assemblies of Finite Shapes: Design and Self-Assembly ...

    Indian Academy of Sciences (India)

    Assembly via Coordination · Slide 2 · Slide 3 · Slide 4 · Slide 5 · Slide 6 · Slide 7 · Slide 8 · Slide 9 · Slide 10 · Slide 11 · Slide 12 · Slide 13 · Slide 14 · Slide 15 · Slide 16 · Slide 17 · Slide 18 · Slide 19 · Slide 20 · Slide 21 · Molecular Box · Slide 23.

  19. Probing the structure of ribosome assembly intermediates in vivo using DMS and hydroxyl radical footprinting.

    Science.gov (United States)

    Hulscher, Ryan M; Bohon, Jen; Rappé, Mollie C; Gupta, Sayan; D'Mello, Rhijuta; Sullivan, Michael; Ralston, Corie Y; Chance, Mark R; Woodson, Sarah A

    2016-07-01

    The assembly of the Escherichia coli ribosome has been widely studied and characterized in vitro. Despite this, ribosome biogenesis in living cells is only partly understood because assembly is coupled with transcription, modification and processing of the pre-ribosomal RNA. We present a method for footprinting and isolating pre-rRNA as it is synthesized in E. coli cells. Pre-rRNA synthesis is synchronized by starvation, followed by nutrient upshift. RNA synthesized during outgrowth is metabolically labeled to facilitate isolation of recent transcripts. Combining this technique with two in vivo RNA probing methods, hydroxyl radical and DMS footprinting, allows the structure of nascent RNA to be probed over time. Together, these can be used to determine changes in the structures of ribosome assembly intermediates as they fold in vivo. Copyright © 2016 Elsevier Inc. All rights reserved.

  20. Functional alterations of human platelets following indium-111 labelling using different incubation media and labelling agents

    International Nuclear Information System (INIS)

    Isaka, Yoshinari; Imaizumi, Masatoshi; Kimura, Kazufumi; Matsumoto, Masayasu; Kamada, Takenobu

    1991-01-01

    Human platelets were labelled in the absence of presence of plasma using 111 In-labelled oxine sulphate, tropolone or 2-mercaptopyridine-N-oxide (MPO). Under in vitro and in vivo conditions, platelet functions were evaluated by measuring their aggregability, survival, recovery and early distribution. High labelling efficiency was achieved in saline labelling, whereas with plasma labelling, it was necessary to concentrate the platelet-rich plasma to 4.8x10 6 platelets/μl. The aggregation of platelets labelled in plasma or saline was compared with that of controls; platelets labelled in saline showed lower aggregability in 2 μM ADP but not in 5 μM ADP nor with collagen. No significant differences in platelet survival and recovery were noted between platelets labelled in plasma and those labelled in saline. Our results indicate that partial loss of ADP aggregability in vitro does not influence the in vivo viability of platelets labelled in saline. Scintigraphic studies showed that platelets labelled in a saline medium were temporarily sequestrated in the liver but not in the spleen or heart. Thus, platelet labelling in saline does not affect platelet function adversely, but platelets labelled in plasma are more desirable for assessing the early distribution of platelets in the reticuloendothelial system. (orig.)

  1. ML-MG: Multi-label Learning with Missing Labels Using a Mixed Graph

    KAUST Repository

    Wu, Baoyuan

    2015-12-07

    This work focuses on the problem of multi-label learning with missing labels (MLML), which aims to label each test instance with multiple class labels given training instances that have an incomplete/partial set of these labels (i.e. some of their labels are missing). To handle missing labels, we propose a unified model of label dependencies by constructing a mixed graph, which jointly incorporates (i) instance-level similarity and class co-occurrence as undirected edges and (ii) semantic label hierarchy as directed edges. Unlike most MLML methods, We formulate this learning problem transductively as a convex quadratic matrix optimization problem that encourages training label consistency and encodes both types of label dependencies (i.e. undirected and directed edges) using quadratic terms and hard linear constraints. The alternating direction method of multipliers (ADMM) can be used to exactly and efficiently solve this problem. To evaluate our proposed method, we consider two popular applications (image and video annotation), where the label hierarchy can be derived from Wordnet. Experimental results show that our method achieves a significant improvement over state-of-the-art methods in performance and robustness to missing labels.

  2. Synthesis of carboxy-labelled 1-carnitine

    Energy Technology Data Exchange (ETDEWEB)

    Goodfellow, D.B.; Hoppel, C.L.; Turkaly, J.S. (Case Western Reserve Univ., Cleveland, OH (USA). School of Medicine)

    1982-03-01

    A method for the production of carboxy-labelled l-carnitine is described. The first step is the chemical synthesis of 4-N-trimethylammoniobutanoate (butyrobetaine) from the precursors 4-aminobutanoate and iodomethane. The second step involves the hydroxylation of butyrobetaine to form l-carnitine using butyrobetaine hydroxylase partially purified from bovine calf liver. The method also can be used to synthesize Me-labelled and uniformly-chain-labelled l-carnitine.

  3. From the assembly line; Am laufenden Band

    Energy Technology Data Exchange (ETDEWEB)

    Weber, Tilman

    2010-04-15

    Wind turbine nacelles are commonly produced in assembly lines. Now, producers are working on models for serial automatic production, with the primary intention of being able to export them and integrate them in assembly lines abroad. (orig.)

  4. Autonomous Assembly of Structures in Space

    Data.gov (United States)

    National Aeronautics and Space Administration — In-orbit assembly of structures is a task that must be performed by space-walking humans, and yet it is costly, time-consuming, and potentially dangerous. Assembly...

  5. Eye tracking and nutrition label use

    DEFF Research Database (Denmark)

    Graham, Dan J.; Orquin, Jacob Lund; Visschers, Vivianne H.M.

    2012-01-01

    cameras monitoring consumer visual attention (i.e., eye tracking) has begun to identify ways in which label design could be modified to improve consumers’ ability to locate and effectively utilize nutrition information. The present paper reviews all published studies of nutrition label use that have...... utilized eye tracking methodology, identifies directions for further research in this growing field, and makes research-based recommendations for ways in which labels could be modified to improve consumers’ ability to use nutrition labels to select healthful foods....

  6. Magnetic scanning of LWR fuel assemblies

    International Nuclear Information System (INIS)

    Fiarman, S.; Moodenbaugh, A.

    1980-01-01

    Nondestructive assay (NDA) techniques are available both for fresh and spent fuel, but generally are too time consuming and do not uniquely identify an assembly. A new method is reported to obtain a signature from a magnetic scan of each assembly. This scan is an NDA technique that detects magnetic inclusions. It is potentially fast (5 min/assembly), and may provide a unique signature from the magnetic properties of each fuel assembly

  7. Uracil Excision for Assembly of Complex Pathways

    DEFF Research Database (Denmark)

    Cavaleiro, Mafalda; Nielsen, Morten Thrane; Kim, Se Hyeuk

    2015-01-01

    Despite decreasing prices on synthetic DNA constructs, higher-order assembly of PCR-generated DNA continues to be an important exercise in molecular and synthetic biology. Simplicity and robustness are attractive features met by the uracil excision DNA assembly method, which is one of the most in...... genes into the genome, and a standardized assembly pipeline using benchmarked oligonucleotides for pathway assembly and multigene expression optimization....

  8. Virtual Reality and Haptics for Product Assembly

    Directory of Open Access Journals (Sweden)

    Maria Teresa Restivo

    2012-01-01

    Full Text Available Haptics can significantly enhance the user's sense of immersion and interactivity. An industrial application of virtual reality and haptics for product assembly is described in this paper, which provides a new and low-cost approach for product assembly design, assembly task planning and assembly operation training. A demonstration of the system with haptics device interaction was available at the session of exp.at'11.

  9. Plutonium demonstration assemblies in the CNA core

    International Nuclear Information System (INIS)

    Romain, J.L.

    1975-01-01

    The SENA (Societe d'Exploitation Nucleaire des Ardennes) has decided to load two plutonium assemblies at the beginning of the 6th cycle of the CNA (Centrale Nucleaire des Ardennes). These assemblies will be loaded in September 1975 and will undergo three irradiation cycles. A general description of these two assemblies and nuclear design calculations that have been performed are presented [fr

  10. Snowball: Strain aware gene assembly of Metagenomes

    NARCIS (Netherlands)

    I. Gregor; A. Schönhuth (Alexander); A.C. McHardy (Alice)

    2015-01-01

    htmlabstractGene assembly is an important step in functional analysis of shotgun metagenomic data. Nonetheless, strain aware assembly remains a challenging task, as current assembly tools often fail to distinguish among strain variants or require closely related reference genomes of the studied

  11. Snowball: strain aware gene assembly of metagenomes

    NARCIS (Netherlands)

    I. Gregor; A. Schönhuth (Alexander); A.C. McHardy (Alice)

    2016-01-01

    textabstractMotivation: Gene assembly is an important step in functional analysis of shotgun metagenomic data. Nonetheless, strain aware assembly remains a challenging task, as current assembly tools often fail to distinguish among strain variants or require closely related reference genomes of the

  12. Supramolecular assemblies based on glycoconjugated dyes

    NARCIS (Netherlands)

    Schmidt, B.

    2016-01-01

    Supramolecular assemblies of glycoconjugated dyes can be tailored with properties that make them attractive for use in biomedical applications. For example, when assemblies of glycoconjugated dyes are displaying carbohydrates on their periphery in a polyvalent manner, these assemblies can be used to

  13. Nuclear fuel sub-assemblies

    International Nuclear Information System (INIS)

    Dodd, J.A.; Butterfield, C.E.; Waite, E.

    1979-01-01

    A fast reactor fuel sub-assembly has honeycomb grids for laterally supporting the fuel pins. The grids are of two series and are arranged alternately along the bundle. The grids of a first series provide a discrete cell for each pin but the grids of the second series have a peripheral group of cells only. The grids of the second series provide intermediate support of the edge pins to restrain bow. (author)

  14. Resistor assemblies for NEC accelerators

    International Nuclear Information System (INIS)

    Weisser, D.C.

    1990-01-01

    Resistor assemblies have been under test in the 14UD Pelletron at the Australian National University in Canberra, Australia since February 1988, with no failures. A full set of resistors was installed in March 1989 and their performances has been satisfactory. The design incorporates coaxial shielding and individual mounting resulting in excellent flexibility in installation and maintenance. A pair of resistors is used to span each insulated gap. The design can be easily adapted to other types of accelerators. (orig.)

  15. Biologically Assembled Quantum Electronic Arrays

    Science.gov (United States)

    2013-06-07

    sequences identification using different M13 phage phage libraries. 65 sequences have been passed on to TY’s group. 3b. Pt binding sequence, Pt...platinum surface as a part of M13 phage coat protein, retains the strong binding ability to the crystal surface. The strong binding ability can be...and demonstrated interesting trimer assembly of Pt nanoparticles on protein. Approaches Phage display technique is used to select peptide sequences

  16. Systematic Comparison of Label-Free, Metabolic Labeling, and Isobaric Chemical Labeling for Quantitative Proteomics on LTQ Orbitrap Velos

    Energy Technology Data Exchange (ETDEWEB)

    Li, Zhou [ORNL; Adams, Rachel M [ORNL; Chourey, Karuna [ORNL; Hurst, Gregory {Greg} B [ORNL; Hettich, Robert {Bob} L [ORNL; Pan, Chongle [ORNL

    2012-01-01

    A variety of quantitative proteomics methods have been developed, including label-free, metabolic labeling, and isobaric chemical labeling using iTRAQ or TMT. Here, these methods were compared in terms of the depth of proteome coverage, quantification accuracy, precision, and reproducibility using a high-performance hybrid mass spectrometer, LTQ Orbitrap Velos. Our results show that (1) the spectral counting method provides the deepest proteome coverage for identification, but its quantification performance is worse than labeling-based approaches, especially the quantification reproducibility; (2) metabolic labeling and isobaric chemical labeling are capable of accurate, precise, and reproducible quantification and provide deep proteome coverage for quantification. Isobaric chemical labeling surpasses metabolic labeling in terms of quantification precision and reproducibility; (3) iTRAQ and TMT perform similarly in all aspects compared in the current study using a CID-HCD dual scan configuration. Based on the unique advantages of each method, we provide guidance for selection of the appropriate method for a quantitative proteomics study.

  17. EFTF cobalt test assembly results

    International Nuclear Information System (INIS)

    Rawlins, J.A.; Wootan, D.W.; Carter, L.L.; Brager, H.R.; Schenter, R.E.

    1988-01-01

    A cobalt test assembly containing yttrium hydride pins for neutron moderation was irradiated in the Fast Flux Test Facility during Cycle 9A for 137.7 equivalent full power days at a power level fo 291 MW. The 36 test pins consisted of a batch of 32 pins containing cobalt metal to produce Co-60, and a set of 4 pins with europium oxide to produce Gd-153, a radioisotope used in detection of the bone disease Osteoporosis. Post-irradiation examination of the cobalt pins determined the Co-60 produced with an accuracy of about 5 %. The measured Co-60 spatially distributed concentrations were within 20 % of the calculated concentrations. The assembly average Co-60 measured activity was 4 % less than the calculated value. The europium oxide pins were gamma scanned for the europium isotopes Eu-152 and Eu-154 to an absolute accuracy of about 10 %. The measured europium radioisotpe anc Gd-153 concentrations were within 20 % of calculated values. In conclusion, the hydride assembly performed well and is an excellent vehicle for many Fast Flux Test Facility isotope production applications. The results also demonstrate that the calculational methods developed by the Westinghouse Hanford Company are very accurate. (author)

  18. [(64) Cu]-labelled trastuzumab

    DEFF Research Database (Denmark)

    Schjoeth-Eskesen, Christina; Nielsen, Carsten Haagen; Heissel, Søren

    2015-01-01

    ,7 acetic acid (NODAGA) analogue in a preliminary HER2 tumour mouse model. The chelators were conjugated to trastuzumab using the activated esters DOTA mono-N-hydroxysuccinimide (NHS) and NODAGA-NHS. (64) Cu-labelling of DOTA-trastuzumab was studied by varying the amount of DOTA-trastuzumab used, reaction...... [(64) Cu]DOTA-trastuzumab and [(64) Cu]NODAGA-trastuzumab were produced after purification with radiochemical purities of >97%. The tracers were injected into mice with HER2 expressing tumours. The mice were imaged by positron emission tomography and showed high tumour uptake of 3-9% ID/g for both......The human epidermal growth factor receptor-2 (HER2) is overexpressed in 20-30% of all breast cancer cases, leading to increased cell proliferation, growth and migration. The monoclonal antibody, trastuzumab, binds to HER2 and is used for treatment of HER2-positive breast cancer. Trastuzumab has...

  19. F-18 labeled 3-fluorodiazepam

    Energy Technology Data Exchange (ETDEWEB)

    Luxen, A.; Barrio, J.R.; Bida, G.T.; Satyamurthy, N.; Phelps, M.E.

    1985-05-01

    3-Fluorodiazepam is a new and potent antianxiety agent with prolonged action. The authors found that molecular fluorine (0.5% in Ne) reacts cleanly with diazepam in freon or chloroform at room temperature to produce 3-fluorodiazepam in good yields. Successful syntheses have employed 2:1 to 5:1 molar ratios diazepam: fluorine to minimize the formation of byproducts. (/sup 18/F) 3-Fluorodiazepam, a potential candidate for PET studies, (specific activity 3-5 Ci/mmol) has been synthesized from /sup 18/F-F/sub 2/ using the same procedure, followed by column chromatographic purification (Silicagel, dichloromethane: ethyl acetate, 5:1) with a radiochemical yield of 12-20% (50% maximum) and a chemical and radiochemical purity >99% as judged by reversed-phase high pressure liquid chromatography analysis (Ultrasyl octyl column, 10 ..mu.. m, 4.6 x 250 mm i.d., 60% MeOH 40% water; flow rate, 1.0 ml/min; retention time for (/sup 18/F) fluorodiazepam, 11.4 min; for diazepam, 13.5 min; radioactivity and ultraviolet detectors). Lower radiochemical yields (5-7%), and significant formation of by-products were observed when (/sup 18/F)acetylhypofluorite, prepared in the gasphase, was used as the reagent. Readily accessible routes to /sup 18/F-labeled benzodiazepines of higher specific activity were also investigated. Approaches to the synthesis of high specific activity (>200 Ci/mmol) (/sup 18/F)3-fluorodiazepam involve nucleophilic displacement at carbon-3 (e.g. from 3-chlorodiazepam) with (/sup 18/F)fluoride ion. The results presented here demonstrate the synthetic accessibility of /sup 18/F-labeled benzodiazepines for application in neurotransmitter ligand studies with PET.

  20. Chain store management through private labels strategy

    Directory of Open Access Journals (Sweden)

    Martina Sopta

    2007-07-01

    Full Text Available The purpose of this paper is to examine the market shares of private labels in the European Union and on the global market, and to compare the results of the analysis with the level of presence of private labels on the Croatian market. Moreover, through the application of macro and microeconomic tools, the author tried to estimate the future trends of private labels in Croatia.For the purpose of the paper secondary and primary data was used in the research. Relevant scientific and professional literature of local and foreign authors was analyzed. In addition, a few recent research studies were analyzed and their results compared. Field research has been conducted by the survey method, with 225 respondents included in the intentional sample.The main hypothesis of the paper based on research is that, in total sales, private labels are gaining a growing share in all markets, regardless of the development level of those markets. Alongside the main hypothesis of the work, three supporting hypotheses were tested to see which private labels are a good alternative to other brands on the world market. Private labels are generally developed on generic products. The third supporting hypothesis starts from the assumption that the investments in the promotion of private labels are negligible, resulting in lower prices of thoseproducts. The results of research and analyses in the work indicate that the position of private labels will strengthen internationally, as part of the process of liberalization and globalization of trade flows. In the process of purchase of private labels the positioning of the point of sale and price have an increasing contribution. With the concentration of commerce in chain stores, the share of private labels grows, approaching a half of the total sales in some countries. Considering the Croatian market, according to the international product life cycle theory, the share of private labels in the total sales will grow in the future

  1. Portion size labeling and intended soft drink consumption : the impact of labeling format and size portfolio

    NARCIS (Netherlands)

    Vermeer, Willemijn M; Steenhuis, Ingrid H M; Leeuwis, Franca H; Bos, Arjan E R; de Boer, Michiel; Seidell, Jacob C

    2010-01-01

    OBJECTIVE: To assess what portion size labeling format is most promising in helping consumers selecting appropriate soft drink sizes, and whether labeling impact depends on the size portfolio. METHODS: An experimental study was conducted in fast-food restaurants in which 2 labeling formats (ie,

  2. Experimental investigation of transmission properties and label swapping of an orthogonal ASK/FSK labeled signal

    DEFF Research Database (Denmark)

    Chi, Nan; Yu, S.Y.; Xu, Lin

    2005-01-01

    This paper presents an experimental assessment of the transmission performance and all-optical label swapping for an orthogonal amplitude-shift keying-frequency-shift keying (ASK/FSK) labeled signal. Transmission through different dispersion maps with various compensation schemes and fiber types ...... is investigated. All-optical label erasure, reinsertion, and multihop transmission are experimentally demonstrated....

  3. Multi-label Learning with Missing Labels Using Mixed Dependency Graphs

    KAUST Repository

    Wu, Baoyuan

    2018-04-06

    This work focuses on the problem of multi-label learning with missing labels (MLML), which aims to label each test instance with multiple class labels given training instances that have an incomplete/partial set of these labels (i.e., some of their labels are missing). The key point to handle missing labels is propagating the label information from the provided labels to missing labels, through a dependency graph that each label of each instance is treated as a node. We build this graph by utilizing different types of label dependencies. Specifically, the instance-level similarity is served as undirected edges to connect the label nodes across different instances and the semantic label hierarchy is used as directed edges to connect different classes. This base graph is referred to as the mixed dependency graph, as it includes both undirected and directed edges. Furthermore, we present another two types of label dependencies to connect the label nodes across different classes. One is the class co-occurrence, which is also encoded as undirected edges. Combining with the above base graph, we obtain a new mixed graph, called mixed graph with co-occurrence (MG-CO). The other is the sparse and low rank decomposition of the whole label matrix, to embed high-order dependencies over all labels. Combining with the base graph, the new mixed graph is called as MG-SL (mixed graph with sparse and low rank decomposition). Based on MG-CO and MG-SL, we further propose two convex transductive formulations of the MLML problem, denoted as MLMG-CO and MLMG-SL respectively. In both formulations, the instance-level similarity is embedded through a quadratic smoothness term, while the semantic label hierarchy is used as a linear constraint. In MLMG-CO, the class co-occurrence is also formulated as a quadratic smoothness term, while the sparse and low rank decomposition is incorporated into MLMG-SL, through two additional matrices (one is assumed as sparse, and the other is assumed as low

  4. Nuclear fuel assembly identification using computer vision

    International Nuclear Information System (INIS)

    Moffett, S.D.

    1985-01-01

    This report describes an improved method of remotely identifying irradiated nuclear fuel assemblies. The method uses existing in-cell TV cameras to input an image of the notch-coded top of the fuel assemblies into a computer vision system, which then produces the identifying number for that assembly. This system replaces systems that use either a mechanical mechanism to feel the notches or use human operators to locate notches visually. The system was developed for identifying fuel assemblies from the Fast Flux Test Facility (FFTF) and the Clinch River Breeder Reactor, but could be used for other reactor assembly identification, as appropriate

  5. Assembly of cucumber (Cucumis sativus L.) somaclones

    Science.gov (United States)

    Skarzyńska, Agnieszka; Kuśmirek, Wiktor; Pawełkowicz, Magdalena; PlÄ der, Wojciech; Nowak, Robert M.

    2017-08-01

    The development of next generation sequencing opens the possibility of using sequencing in various plant studies, such as finding structural changes and small polymorphisms between species and within them. Most analyzes rely on genomic sequences and it is crucial to use well-assembled genomes of high quality and completeness. Herein we compare commonly available programs for genomic assembling and newly developed software - dnaasm. Assemblies were tested on cucumber (Cucumis sativus L.) lines obtained by in vitro regeneration (somaclones), showing different phenotypes. Obtained results shows that dnaasm assembler is a good tool for short read assembly, which allows obtaining genomes of high quality and completeness.

  6. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Watch this video for tips on figuring out food labels so you can make healthy choices. More on this topic for: Parents Kids Teens Keeping Portions Under Control Figuring Out Food Labels Healthy Food Shopping If My Child Has ...

  7. 76 FR 45715 - Appliance Labeling Rule

    Science.gov (United States)

    2011-08-01

    ... bulbs (often cardboard sheets with plastic bulb covers) have little or no room for the new label. \\13... many consumers. And, although typical usage patterns (e.g., hours per day of operation) may vary for these products, the standard usage assumption on the Lighting Facts label (i.e., three hours per day...

  8. Influence of Food Labels on Adolescent Diet.

    Science.gov (United States)

    Misra, Ranjita

    2002-01-01

    Provides information on food nutrition labels and discusses the benefits of adolescents' using them to plan healthy diets. Suggests that teachers and educators should encourage appropriate label reading education for adolescents to promote healthy eating practices. Provides definitions of nutrient content claims. (SG)

  9. 16 CFR 309.17 - Labels.

    Science.gov (United States)

    2010-01-01

    ... vehicle fuels (including electricity), and the color of the knock-out type within the black band, is... ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Label Specifications... alternative vehicle fuel (other than electricity) labels with disclosure of principal component only. The...

  10. 40 CFR 86.413-78 - Labeling.

    Science.gov (United States)

    2010-07-01

    ... be of a color that contrasts with the background of the label: (i) The label heading. Vehicle... EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for 1978 and Later New..., containing the information hereinafter provided, to all production models of such vehicles available for sale...

  11. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... site Sitio para adolescentes Body Mind Sexual Health Food & Fitness Diseases & Conditions Infections Drugs & Alcohol School & Jobs Sports Expert Answers (Q&A) Staying Safe Videos for Educators ... español Cómo leer las etiquetas de datos nutricionales (video) Most packaged foods come with a Nutrition Facts label. These labels ...

  12. Private labels : The brands of the future

    NARCIS (Netherlands)

    Keller, Kristopher

    2017-01-01

    This dissertation consists of three essays that study private labels’ evolution from private labels as brand class to individual private-label brands from three different perspectives. In the second chapter of this dissertation (essay 1), I study the antecedents and performance implications of

  13. 16 CFR 1511.7 - Labeling.

    Science.gov (United States)

    2010-01-01

    ... PACIFIERS § 1511.7 Labeling. (a) As required by paragraphs (b) and (c) of this section, pacifiers shall be labeled with the statement: “Warning—Do Not Tie Pacifier Around Child's Neck as it Presents a... and conspicuously on any retail display carton containing two or more pacifiers. (c) Each individually...

  14. The anatomy of a laser label

    Science.gov (United States)

    Laser labeling of fruits and vegetables is an efficient alternative to adhesive tags. The advantages of this system are numerous. In general the label consists of alphanumerical characters formed by laser generated pinhole depressions that penetrate the produce’s surface creating visible markings. H...

  15. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Talk to Your Child About the News Gun Safety Too Late for the Flu Vaccine? Eating Disorders Arrhythmias ... español Cómo leer las etiquetas de datos nutricionales (video) Most packaged foods come with a Nutrition Facts label. These labels ...

  16. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... label. These labels have a lot of important information — on fat and calories, serving sizes, sodium content, ... Nondiscrimination Visit the Nemours Web site. Note: All information on KidsHealth® is for educational purposes only. For ...

  17. On the complexity of labeled oriented trees

    Indian Academy of Sciences (India)

    Abstract. We define a notion of complexity for labeled oriented trees (LOTs) related to the bridge number in knot theory and prove that LOTs of complexity 2 are aspherical. We also present a class of LOTs of higher complexity which is aspherical, give an upper bound for the complexity of labeled oriented intervals and study ...

  18. 10 CFR 20.1904 - Labeling containers.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Labeling containers. 20.1904 Section 20.1904 Energy....1904 Labeling containers. (a) The licensee shall ensure that each container of licensed material bears... handling or using the containers, or working in the vicinity of the containers, to take precautions to...

  19. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Educators Search English Español How to Read a Nutrition Facts Label (Video) KidsHealth / For Parents / How to Read a Nutrition Facts Label (Video) Print en español Cómo leer ...

  20. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... A) Staying Safe Videos for Educators Search English Español How to Read a Nutrition Facts Label (Video) ... Read a Nutrition Facts Label (Video) Print en español Cómo leer las etiquetas de datos nutricionales (video) ...

  1. Do European consumers use nutrition labels?

    DEFF Research Database (Denmark)

    Wills, Josephine M.; Grunert, Klaus G.; Celemín, Laura Fernández

    2009-01-01

    Nutrition labelling on food packages becomes more and more widespread in the European Union. Such information is not compulsory, unless a nutrition or health claim is made. However, how do consumers use nutrition information? Two European studies are currently assessing whether nutrition...... knowledge about nutrition and are able to use nutrition labels to identify healthier products within a category....

  2. The preparation of radioiodine labelled amiodarone

    International Nuclear Information System (INIS)

    Gong Jialing; Yan Ping; Li Yanru

    1987-01-01

    Radioiodine labelled amiodarone can be conveniently obtained in the presence of copper(II) and excess reductant by hydrothermal method, at 100 deg C for 1 hour and separated by thin layer chromatography (TLC). Labelling efficiency is over 95%. Radiochemical purity is over 95%. The hydrothermal exchange method is a simple monocompartment isotope exchange reaction in homogeneous system and obeys the exponential law

  3. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Behavior School & Family Life First Aid & Safety Doctors & Hospitals Videos Recipes for Kids Kids site Sitio para ... nutricionales (video) Most packaged foods come with a Nutrition Facts label. These labels have a lot of important ... Policy Permissions Guidelines Privacy Policy & Terms of Use Notice ...

  4. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... for Educators Search English Español How to Read a Nutrition Facts Label (Video) KidsHealth / For Parents / How to Read a Nutrition Facts Label (Video) Print en español Cómo ...

  5. Methods of synthesis of deuterium labelled lipids

    International Nuclear Information System (INIS)

    Bragina, N.A.; Chupin, V.V.

    1997-01-01

    Methods for synthesis of deuterium-labelled hydrophobic and hydrophilic lipid molecules and ways of obtaining selectively and completely deuterized phospholipids and their analogues are considered. The deuterium-labelled lipids are used for studies on structural organization and functioning of biological membranes, including studies with the NMP and neutron-diffraction methods of lipid-lipid and lipid-protein interactions

  6. Conformational change of spin labelled myoglobin

    International Nuclear Information System (INIS)

    Wajnberg, E.; Ribeiro, P.C.; Nascimento, O.R.; Bemski, G.

    1978-01-01

    A conformational change of spin labelled myoglobin have been followed by measuring the spin label's (isothiocyanate) correlation time for temperatures between 18 0 C and 44 0 C. The correlation time was calculated from Electrom Paramagnetic Ressonance Spectra using the components of the espectroscopic and hiperfine tensors obtained by fitting the powder spectra using Lefebvre and Maruani's program- [pt

  7. A note on root projection and labelling*

    African Journals Online (AJOL)

    Kate H

    Abstract. This paper identifies a problem with a hypothesis put forward in Chomsky (2013) in relation to his labelling algorithm. Chomsky suggests that category-neutral roots do not qualify as labels and cannot project. However, I provide evidence that the derivation of particle verbs involves the projection of a ...

  8. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... healthy choices. More on this topic for: Parents Kids Teens Keeping Portions Under Control Figuring Out Food Labels Healthy Food Shopping If My Child Has Food Allergies, What Should I Look for When Reading Food Labels? Healthy Eating Kids and Food: 10 Tips for Parents Figuring Out ...

  9. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Health Food & Fitness Diseases & Conditions Infections Drugs & Alcohol School & Jobs Sports Expert Answers (Q&A) Staying Safe Videos for Educators Search English Español How to Read a Nutrition Facts Label (Video) KidsHealth / For Parents / How to Read a Nutrition Facts Label (Video) ...

  10. Genome Sequence Databases (Overview): Sequencing and Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Lapidus, Alla L.

    2009-01-01

    From the date its role in heredity was discovered, DNA has been generating interest among scientists from different fields of knowledge: physicists have studied the three dimensional structure of the DNA molecule, biologists tried to decode the secrets of life hidden within these long molecules, and technologists invent and improve methods of DNA analysis. The analysis of the nucleotide sequence of DNA occupies a special place among the methods developed. Thanks to the variety of sequencing technologies available, the process of decoding the sequence of genomic DNA (or whole genome sequencing) has become robust and inexpensive. Meanwhile the assembly of whole genome sequences remains a challenging task. In addition to the need to assemble millions of DNA fragments of different length (from 35 bp (Solexa) to 800 bp (Sanger)), great interest in analysis of microbial communities (metagenomes) of different complexities raises new problems and pushes some new requirements for sequence assembly tools to the forefront. The genome assembly process can be divided into two steps: draft assembly and assembly improvement (finishing). Despite the fact that automatically performed assembly (or draft assembly) is capable of covering up to 98% of the genome, in most cases, it still contains incorrectly assembled reads. The error rate of the consensus sequence produced at this stage is about 1/2000 bp. A finished genome represents the genome assembly of much higher accuracy (with no gaps or incorrectly assembled areas) and quality ({approx}1 error/10,000 bp), validated through a number of computer and laboratory experiments.

  11. Assembly study for JT-60SA tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Shibanuma, K., E-mail: shibanuma.kiyoshi@jaea.go.jp [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Arai, T.; Hasegawa, K.; Hoshi, R.; Kamiya, K.; Kawashima, H.; Kubo, H.; Masaki, K.; Saeki, H.; Sakurai, S.; Sakata, S.; Sakasai, A.; Sawai, H.; Shibama, Y.K.; Tsuchiya, K.; Tsukao, N.; Yagyu, J.; Yoshida, K.; Kamada, Y. [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Mizumaki, S. [Toshiba Corporation, Minato-ku, Tokyo 105-8001 (Japan); and others

    2013-10-15

    The assembly scenarios and assembly tools of the major tokamak components for JT-60SA are studied in the following. (1) The assembly frame (with a dedicated 30-tonne crane), which is located around the JT-60SA tokamak, is adopted for effective assembly works in the torus hall and the temporary support of the components during assembly. (2) Metrology for precise positioning of the components is also studied by defining the metrology points on the components. (3) The sector segmentation for weld joints and positioning of the vacuum vessel (VV), the assembly scenario and tools for VV thermal shield (TS), the connection of the outer intercoil structure (OIS) and the installation of the final toroidal field coil (TFC) are studied, as typical examples of the assembly scenarios and tools for JT-60SA.

  12. Capacitor assembly and related method of forming

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Lili; Tan, Daniel Qi; Sullivan, Jeffrey S.

    2017-12-19

    A capacitor assembly is disclosed. The capacitor assembly includes a housing. The capacitor assembly further includes a plurality of capacitors disposed within the housing. Furthermore, the capacitor assembly includes a thermally conductive article disposed about at least a portion of a capacitor body of the capacitors, and in thermal contact with the capacitor body. Moreover, the capacitor assembly also includes a heat sink disposed within the housing and in thermal contact with at least a portion of the housing and the thermally conductive article such that the heat sink is configured to remove heat from the capacitor in a radial direction of the capacitor assembly. Further, a method of forming the capacitor assembly is also presented.

  13. Dynamic pathways for viral capsid assembly

    Energy Technology Data Exchange (ETDEWEB)

    Hagan, Michael F.; Chandler, David

    2006-02-09

    We develop a class of models with which we simulate the assembly of particles into T1 capsid-like objects using Newtonian dynamics. By simulating assembly for many different values of system parameters, we vary the forces that drive assembly. For some ranges of parameters, assembly is facile, while for others, assembly is dynamically frustrated by kinetic traps corresponding to malformed or incompletely formed capsids. Our simulations sample many independent trajectories at various capsomer concentrations, allowing for statistically meaningful conclusions. Depending on subunit (i.e., capsomer) geometries, successful assembly proceeds by several mechanisms involving binding of intermediates of various sizes. We discuss the relationship between these mechanisms and experimental evaluations of capsid assembly processes.

  14. Impact analysis of spent fuel jacket assemblies

    International Nuclear Information System (INIS)

    Aramayo, G.A.

    1994-01-01

    As part of the analyses performed in support of the reracking of the High Flux Isotope Reactor pool, it became necessary to prove the structural integrity of the spent fuel jacket assemblies subjected to gravity drop that result from postulated accidents associated with the handling of these assemblies while submerged in the pool. The spent fuel jacket assemblies are an integral part of the reracking project, and serve to house fuel assemblies. The structure integrity of the jacket assemblies from loads that result from impact from a height of 10 feet onto specified targets has been performed analytically using the computer program LS-DYNA3D. Nine attitudes of the assembly at the time of impact have been considered. Results of the analyses show that there is no failure of the assemblies as a result of the impact scenarios considered

  15. Deterministic nanoparticle assemblies: from substrate to solution

    International Nuclear Information System (INIS)

    Barcelo, Steven J; Gibson, Gary A; Yamakawa, Mineo; Li, Zhiyong; Kim, Ansoon; Norris, Kate J

    2014-01-01

    The deterministic assembly of metallic nanoparticles is an exciting field with many potential benefits. Many promising techniques have been developed, but challenges remain, particularly for the assembly of larger nanoparticles which often have more interesting plasmonic properties. Here we present a scalable process combining the strengths of top down and bottom up fabrication to generate deterministic 2D assemblies of metallic nanoparticles and demonstrate their stable transfer to solution. Scanning electron and high-resolution transmission electron microscopy studies of these assemblies suggested the formation of nanobridges between touching nanoparticles that hold them together so as to maintain the integrity of the assembly throughout the transfer process. The application of these nanoparticle assemblies as solution-based surface-enhanced Raman scattering (SERS) materials is demonstrated by trapping analyte molecules in the nanoparticle gaps during assembly, yielding uniformly high enhancement factors at all stages of the fabrication process. (paper)

  16. 9 CFR 112.5 - Review and approval of labeling.

    Science.gov (United States)

    2010-01-01

    ... container label, carton label, and enclosure. Sketches must be legible, and must include all information... product two copies of each sketch of an enclosure, label for the smallest size final container, and carton label; Provided, That labels for larger size containers and/or cartons that are identical, except for...

  17. 49 CFR 172.416 - POISON GAS label.

    Science.gov (United States)

    2010-10-01

    ... POISON GAS label and the symbol must be white. The background of the upper diamond must be black and the... 49 Transportation 2 2010-10-01 2010-10-01 false POISON GAS label. 172.416 Section 172.416... SECURITY PLANS Labeling § 172.416 POISON GAS label. (a) Except for size and color, the POISON GAS label...

  18. Energy labeling for electric fans in Malaysia

    International Nuclear Information System (INIS)

    Mahlia, T.M.I.; Masjuki, H.H.; Taha, F.M.; Rahim, N.A.; Saidur, R.

    2005-01-01

    To reduce energy consumption in the residential sector, Malaysia Energy Commission is considering implementing energy labels for household electrical appliances including electric fans in 2005. The purpose of the energy labels is to provide the consumers a guideline to compare the size, features, price and efficiency of the appliance. This paper discusses the energy label for electric fans in this country based on Malaysian Standards developed by a technical committee that reviewed the performance of household electrical appliances. This study includes methodology for the calculation of the energy efficiency star rating and projected energy usage, performance requirements, details of the energy label and the requirements for the valid application in Malaysia. The label also can be adopted for other household electrical appliances with only slight modifications

  19. Off-label Prescription of Medication.

    Science.gov (United States)

    Vrancken, Isabelle

    2015-04-01

    Off-label use of medication refers to prescribing a registered medicine outside its approved marketing authorization, purpose, target group, or indication. Off-label prescription is a widely accepted practice. However, no or little regulation can be found. In this article, the legal status of off-label prescription will be examined. Does off-label prescription fall under the therapeutical freedom and is it free from regulation? Or should we equalize off-label prescription with a therapeutical experimentation and should it follow the rules of experimentation? I will also examine whether the patient can give an informed consent. Whether or not this is possible leads to intense discussions. Finally, the potential liability of the prescribing physician is of great importance.

  20. Recent developments in blood cell labeling research

    International Nuclear Information System (INIS)

    Srivastava, S.C.; Straub, R.F.; Meinken, G.E.

    1988-01-01

    A number of recent developments in research on blood cell labeling techniques are presented. The discussion relates to three specific areas: (1) a new in vitro method for red blood cell labeling with /sup 99m/Tc; (2) a method for labeling leukocytes and platelets with /sup 99m/Tc; and (3) the use of monoclonal antibody technique for platelet labeling. The advantages and the pitfalls of these techniques are examined in the light of available mechanistic information. Problems that remain to be resolved are reviewed. An assessment is made of the progress as well as prospects in blood cell labeling methodology including that using the monoclonal antibody approach. 37 refs., 4 figs

  1. Recent developments in blood cell labeling research

    Energy Technology Data Exchange (ETDEWEB)

    Srivastava, S.C.; Straub, R.F.; Meinken, G.E.

    1988-09-07

    A number of recent developments in research on blood cell labeling techniques are presented. The discussion relates to three specific areas: (1) a new in vitro method for red blood cell labeling with /sup 99m/Tc; (2) a method for labeling leukocytes and platelets with /sup 99m/Tc; and (3) the use of monoclonal antibody technique for platelet labeling. The advantages and the pitfalls of these techniques are examined in the light of available mechanistic information. Problems that remain to be resolved are reviewed. An assessment is made of the progress as well as prospects in blood cell labeling methodology including that using the monoclonal antibody approach. 37 refs., 4 figs.

  2. Labeled estrogens as mammary tumor probes

    International Nuclear Information System (INIS)

    Feenstra, A.

    1981-01-01

    In this thesis estrogens labeled with a gamma or positron emitting nuclide, called estrogen-receptor binding radiopharmaceuticals are investigated as mammary tumour probes. The requirements for estrogen-receptor binding radiopharmaceuticals are formulated and the literature on estrogens labeled for this purpose is reviewed. The potential of mercury-197/197m and of carbon-11 as label for estrogen-receptor binding radiopharmaceuticals is investigated. The synthesis of 197 Hg-labeled 4-mercury-estradiol and 2-mercury-estradiol and their properties in vitro and in vivo are described. It appears that though basically carbon-11 labeled compounds are very promising as mammary tumour probes, their achievable specific activity has to be increased. (Auth.)

  3. Insight into the labeling mechanism of acceleration selective arterial spin labeling

    DEFF Research Database (Denmark)

    Schmid, Sophie; Petersen, Esben T; Van Osch, Matthias J P

    2017-01-01

    OBJECTIVES: Acceleration selective arterial spin labeling (AccASL) is a spatially non-selective labeling technique, used in traditional ASL methods, which labels spins based on their flow acceleration rather than spatial localization. The exact origin of the AccASL signal within the vasculature......-ASL, combined AccASL and VS-ASL signal, and signal from one module with crushing from the other. RESULTS: The label created with AccASL has an overlap of approximately 50% in the vascular region with VS-ASL, but also originates from smaller vessels closer to the capillaries. CONCLUSION: AccASL is able to label...

  4. Efficient Multi-Label Feature Selection Using Entropy-Based Label Selection

    Directory of Open Access Journals (Sweden)

    Jaesung Lee

    2016-11-01

    Full Text Available Multi-label feature selection is designed to select a subset of features according to their importance to multiple labels. This task can be achieved by ranking the dependencies of features and selecting the features with the highest rankings. In a multi-label feature selection problem, the algorithm may be faced with a dataset containing a large number of labels. Because the computational cost of multi-label feature selection increases according to the number of labels, the algorithm may suffer from a degradation in performance when processing very large datasets. In this study, we propose an efficient multi-label feature selection method based on an information-theoretic label selection strategy. By identifying a subset of labels that significantly influence the importance of features, the proposed method efficiently outputs a feature subset. Experimental results demonstrate that the proposed method can identify a feature subset much faster than conventional multi-label feature selection methods for large multi-label datasets.

  5. Off-label use of vaccines.

    Science.gov (United States)

    Neels, Pieter; Southern, James; Abramson, Jon; Duclos, Philippe; Hombach, Joachim; Marti, Melanie; Fitzgerald-Husek, Alanna; Fournier-Caruana, Jacqueline; Hanquet, Germaine

    2017-04-25

    This article reviews the off-label recommendations and use of vaccines, and focuses on the differences between the labelled instructions on how to use the vaccine as approved by the regulatory authorities (or "label" 1 ), and the recommendations for use issued by public health advisory bodies at national and international levels. Differences between public health recommendations and the product label regarding the vaccine use can lead to confusion at the level of vaccinators and vaccinees and possibly result in lower compliance with national vaccination schedules. In particular, in many countries, the label may contain regulatory restrictions and warnings against vaccination of specific population groups (e.g. pregnant women) due to a lack of evidence of safety from controlled trials at the time of initial licensure of the vaccine, while public health authorities may recommend the same vaccine for that group, based on additional post-marketing data and benefit risk analyses. We provide an overview of the different responsibilities between regulatory authorities and public health advisory bodies, and the rationale for off-label use 2 of vaccines, the challenges involved based on the impact of off-label use in real-life. We propose to reduce off-label use of vaccines by requiring the manufacturer to regularly adapt the label as much as possible to the public health needs as supported by new evidence. This would require manufacturers to collect and report post-marketing data, communicate them to all stakeholders and regulators to extrapolate existing evidence (when acceptable) to other groups or to other brands of a vaccine (class effect 3 ). Regulatory authorities have a key role to play by requesting additional post-marketing data, e.g. in specific target groups. When public health recommendations for vaccine use that are outside labelled indications are considered necessary, good communication between regulatory bodies, public health authorities, companies and

  6. Plural beam electron gun assembly

    International Nuclear Information System (INIS)

    Stratton, M.G.

    1977-01-01

    The invention relates to a cathode ray tube plural-beam-in-line bi-potential electron gun assembly, having applied beam currents of differing levels, manifests structurally modified gun structures to effect focused beam landings at the screen that are evidenced as substantially equi-sized spots thereby providing improved resolution and brightness of the screen imagery. The structural changes embody modifications of the related focusing and accelerator electrodes of the respective guns to provide a partial telescoping arrangement for effecting the discrete placement, forming and shielding of the final focusing lenses. The three lenses so formed are in different planes in partial overlapping axial relationship

  7. Early assembly of cellular life.

    Science.gov (United States)

    Trevors, J T

    2003-04-01

    Popular hypotheses that attempt to explain the origin of prebiotic molecules and cellular life capable of growth and division are not always agreed upon. In this manuscript, information on early bacterial life on Earth is examined using information from several disciplines. For example, knowledge can be integrated from physics, thermodynamics, planetary sciences, geology, biogeochemistry, lipid chemistry, primordial cell structures, cell and molecular biology, microbiology, metabolism and genetics. The origin of life also required a combination of elements, compounds and environmental physical-chemical conditions that allowed cells to assemble in less than a billion years. This may have been widespread in the subsurface of the early Earth located at microscopic physical domains.

  8. Assembly-line Simulation Program

    Science.gov (United States)

    Chamberlain, Robert G.; Zendejas, Silvino; Malhotra, Shan

    1987-01-01

    Costs and profits estimated for models based on user inputs. Standard Assembly-line Manufacturing Industry Simulation (SAMIS) program generalized so useful for production-line manufacturing companies. Provides accurate and reliable means of comparing alternative manufacturing processes. Used to assess impact of changes in financial parameters as cost of resources and services, inflation rates, interest rates, tax policies, and required rate of return of equity. Most important capability is ability to estimate prices manufacturer would have to receive for its products to recover all of costs of production and make specified profit. Written in TURBO PASCAL.

  9. Computer-aided lens assembly

    Science.gov (United States)

    Tomlinson, Richard; Alcock, Rob; Petzing, Jon; Coupland, Jeremy

    2004-01-01

    We propose a computer-aided method of lens manufacture that allows assembly, adjustment, and test phases to be run concurrently until an acceptable level of optical performance is reached. Misalignment of elements within a compound lens is determined by a comparison of the results of physical ray tracing by use of an array of Gaussian laser beams with numerically obtained geometric ray traces. An estimate of misalignment errors is made, and individual elements are adjusted in an iterative manner until performance criteria are achieved. The method is illustrated for the alignment of an air-spaced doublet.

  10. Magnetic control assembly qualification model

    Science.gov (United States)

    Shen, R. C.; Fleming, R.; Rutkowski, M. Z.; Fowler, R. Z.

    1972-01-01

    Fabrication and testing of the magnetic control assembly (MCA) are summarized. The MCA was designed as an add-on unit for certain existing components of the Nimbus and ERTS attitude control system. The MCA system consists of three orthogonal electromagnets; a magnetometer probe capable of sensing external fields in the X, Y, and Z axes; and the control electronics. An operational description of the system is given along with all major drawings and photographs. Manufacturing and inspection procedures are outlined and a chronological list of events is included with the fabrication summary.

  11. Fuel injection assembly for use in turbine engines and method of assembling same

    Science.gov (United States)

    Berry, Jonathan Dwight; Johnson, Thomas Edward; York, William David; Uhm, Jong Ho

    2015-12-15

    A fuel injection assembly for use in a turbine engine is provided. The fuel injection assembly includes an end cover, an endcap assembly, a fluid supply chamber, and a plurality of tube assemblies positioned at the endcap assembly. Each of the tube assemblies includes housing having a fuel plenum and a cooling fluid plenum. The cooling fluid plenum is positioned downstream from the fuel plenum and separated from the fuel plenum by an intermediate wall. The plurality of tube assemblies also include a plurality of tubes that extends through the housing. Each of the plurality of tubes is coupled in flow communication with the fluid supply chamber and a combustion chamber positioned downstream from the tube assembly. The plurality of tube assemblies further includes an aft plate at a downstream end of the cooling fluid plenum. The plate includes at least one aperture.

  12. ORGANIC FOOD LABELING AND CERTIFICATION

    Directory of Open Access Journals (Sweden)

    NICOLETA-ANDREEA NEACSU

    2011-04-01

    Full Text Available In the rush to produce more and more crops to satisfy growing demand producers have had to resort to using a lethal cocktail of pesticides to control disease and insect attack. This has lead to numerous international debates about unhealthy food, the effects of it and the measures that must be taken in order to avoid the harmful effects of genetically modified food consumption demonstrated by specialists. These debates evolve around the benefits of the organic products versus the pure trade trick outlined by some. The organic food movement has earned its well deserved place in many markets around the world. Its prestige is lately being widespread to vast parts of Eastern-Europe as well. Based on data collected from specialized reports and articles on organic products, the aim of this paper is to present the importance of organic products, the regulations on organic food and different labels used around the world in order to certify the organic food products.

  13. Faucet: streaming de novo assembly graph construction.

    Science.gov (United States)

    Rozov, Roye; Goldshlager, Gil; Halperin, Eran; Shamir, Ron

    2018-01-01

    We present Faucet, a two-pass streaming algorithm for assembly graph construction. Faucet builds an assembly graph incrementally as each read is processed. Thus, reads need not be stored locally, as they can be processed while downloading data and then discarded. We demonstrate this functionality by performing streaming graph assembly of publicly available data, and observe that the ratio of disk use to raw data size decreases as coverage is increased. Faucet pairs the de Bruijn graph obtained from the reads with additional meta-data derived from them. We show these metadata-coverage counts collected at junction k-mers and connections bridging between junction pairs-contain most salient information needed for assembly, and demonstrate they enable cleaning of metagenome assembly graphs, greatly improving contiguity while maintaining accuracy. We compared Fauceted resource use and assembly quality to state of the art metagenome assemblers, as well as leading resource-efficient genome assemblers. Faucet used orders of magnitude less time and disk space than the specialized metagenome assemblers MetaSPAdes and Megahit, while also improving on their memory use; this broadly matched performance of other assemblers optimizing resource efficiency-namely, Minia and LightAssembler. However, on metagenomes tested, Faucet,o outputs had 14-110% higher mean NGA50 lengths compared with Minia, and 2- to 11-fold higher mean NGA50 lengths compared with LightAssembler, the only other streaming assembler available. Faucet is available at https://github.com/Shamir-Lab/Faucet. rshamir@tau.ac.il or eranhalperin@gmail.com. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press.

  14. "Why Mama and Papa?" The Development of Social Labels.

    Science.gov (United States)

    Brooks-Gunn, Jeanne; Lewis, Michael

    1979-01-01

    Examined social labels first used for parents, differentiation of parents and others on the basis of labeling behavior, and overgeneralization of social labels in 71 infants ranging in age from 9 to 24 months. (JMB)

  15. 21 CFR 352.52 - Labeling of sunscreen drug products.

    Science.gov (United States)

    2010-04-01

    ...] Labeling § 352.52 Labeling of sunscreen drug products. (a) Statement of identity. The labeling of the... protective clothing, and using sunscreens may reduce the risks of skin aging, skin cancer, and other harmful...

  16. Labelling of food: A challenge for many

    Directory of Open Access Journals (Sweden)

    Henderikx Frans

    2017-01-01

    Full Text Available Background: In food marketing, there is a trend towards artisanal, traditional “honest” food, and simultaneously to good looking, long lasting, multi-purpose food with a clean label. In addition, marketeers like to upgrade the image of the food, including the label, using various digital techniques. This can produce (unintended non-conformities with the current food law on labelling, which in this review, refers to Regulation (EU No 1169/2011 (European Union, 2011. Food and meat labelling have been subjected to increased regulation in the recent years, sometimes after scandals (horse-gate, food fraud, sometimes due to wishes of consumer organisations (nutritional information and sometimes after the introduction of new types of ingredients (sweeteners, phytosterols, nanomaterials. Scope and approach: This review provides information about food labelling. Some experiences gathered by food inspectorate personnel in practice, with reference to the literature data, positive aspects, main problems and trends are discussed. Key findings and conclusion: Food labelling is a complex requirement, with the general demands written down in the harmonized regulation (European Union, 2011. Foods sold by e-commerce must also follow these same regulations. However, many food labels on the market show smaller and/or bigger deviations from the legal requirements, which should be appropriately addressed by the food manufacturers or packers, but also by the competent authorities. Even training of consumers seems to be needed, since all this information is, in the end, intended for consumers to aptly utilise.

  17. Synthesis of carbon-13-labeled tetradecanoic acids.

    Science.gov (United States)

    Sparrow, J T; Patel, K M; Morrisett, J D

    1983-07-01

    The synthesis of tetradecanoic acid enriched with 13C at carbons 1, 3, or 6 is described. The label at the carbonyl carbon was introduced by treating 1-bromotridecane with K13CN (90% enriched) to form the 13C-labeled nitrile, which upon hydrolysis yielded the desired acid. The [3-13C]tetradecanoic acid was synthesized by alkylation of diethyl sodio-malonate with [1-13C]1-bromododecane; the acid was obtained upon saponification and decarboxylation. The label at the 6 position was introduced by coupling the appropriately labeled alkylcadmium chloride with the half acid chloride methyl ester of the appropriate dioic acid, giving the corresponding oxo fatty acid ester. Formation of the tosylhydrazone of the oxo-ester followed by reduction with sodium cyanoborohydride gave the labeled methyl tetradecanoate which, upon hydrolysis, yielded the desired tetradecanoic acid. All tetradecanoic acids were identical to unlabeled analogs as evaluated by gas-liquid chromatography and infrared or NMR spectroscopy. These labeled fatty acids were used subsequently to prepare the correspondingly labeled diacyl phosphatidylcholines.

  18. Tritium labeling for bio-med research

    International Nuclear Information System (INIS)

    Lemmon, R.M.

    1980-01-01

    A very large fraction of what we know about biochemical pathways in the living cell has resulted from the use of radioactively-labeled tracer compounds; the use of tritium-labeled compounds has been particularly important. As research in biochemistry and biology has progressed the need has arisen to label compounds of higher specific activity and of increasing molecular complexity - for example, oligo-nucleotides, polypeptides, hormones, enzymes. Our laboratory has gradually developed special facilities for handling tritium at the kilocurie level. These facilities have already proven extremely valuable in producing labeled compounds that are not available from commercial sources. The principal ways employed for compound labeling are: (1) microwave discharge labeling, (2) catalytic tritio-hydrogenation, (3) catalytic exchange with T 2 O, and (4) replacement of halogen atoms by T. Studies have also been carried out on tritiation by the replacement of halogen atoms with T atoms. These results indicate that carrier-free tritium-labeled products, including biomacromolecules, can be produced in this way

  19. Radiopharmaceutical potential of I-131 labelled chlordiazepoxide

    International Nuclear Information System (INIS)

    Unak, P.; Yurt, F.; Asikoglu, M.; Erener, G.; Ozkilic, H.; Dundar, C.; Tuglular, I.

    1998-01-01

    1,4 Benzodiazepine derivatives have been largely used in Medicine since 1960. Chlordiazepoxide (7-Chloro-2-(methyl amino)-5-phenyl-3H-1.4 benzodiazepine 4-oxide) has been mostly used and the oldest one after diazepam. The aim of this study is labeling of chlordiazepoxide (CDZ) with I-131 and investigation of radiopharmaceutical potential as a benzodiazepine receptor agent. Iodogen has been used as iodination agent. Labeling yields have been determined by ITLC (instant This Layer Chromatography) and Paper Electrophoresis. pH and iodogen amount effects to labeling yields have been examined to obtain optimum reaction conditions. Labeling yield was 90% for 1 mg chlordiazepoxide, 1 mg iodogen, 1 pH, 15-20 minutes at room temperature. Radiopharmaceutical potential of I-131 labeled chlordiazepoxide was searched in vivo experiments carried out on rabbits by using Sophy DX Gamma Camera. I-131 labeled chlordiazepoxide of specific activity 690 MBq/mmol has been injected ear vein of rabbit and static perspectives were taken by pointed time intervals. Brain activity has increased after the injection, reached to maximum in 20th minutes and has not decreased during the imaging time (90 minutes). Obtained results have shown that I-131 labeled chlordiazepoxide can be used as a benzodiazepine receptor radiopharmaceutical for SPECT studies of brain. (author)

  20. Self-assembled nanostructured metamaterials

    Science.gov (United States)

    Ponsinet, Virginie; Baron, Alexandre; Pouget, Emilie; Okazaki, Yutaka; Oda, Reiko; Barois, Philippe

    2017-07-01

    The concept of metamaterials emerged in the years 2000 with the achievement of artificial structures enabling nonconventional propagation of electromagnetic waves, such as negative phase velocity or negative refraction. The electromagnetic response of metamaterials is generally based on the presence of optically resonant elements —or meta-atoms— of sub-wavelength size and well-designed morphology so as to provide the desired electric and magnetic optical properties. Top-down technologies based on lithography techniques have been intensively used to fabricate a variety of efficient electric and magnetic resonators operating from microwave to visible light frequencies. However, the technological limits of the top-down approach are reached in visible light where a huge number of nanometre-sized elements is required. We show here that the bottom-up fabrication route based on the combination of nanochemistry and the self-assembly methods of colloidal physics provide an excellent alternative for the large-scale synthesis of complex meta-atoms, as well as for the fabrication of 2D and 3D samples exhibiting meta-properties in visible light. Contribution to the Focus Issue Self-assemblies of Inorganic and Organic Nanomaterials edited by Marie-Paule Pileni.

  1. Spectrometric assembly for portable installations

    International Nuclear Information System (INIS)

    Kluger, A.; Popescu, C.

    1997-01-01

    The components of the portable spectrometric assembly are: - the detecting probe with Na I(Tl) crystal and air-tight case of industrial type; - a microcomputer; - a unit of analogical processing of the signal from the detecting probe; - a single-channel analyzer with adjustable threshold; - commands and display module; - a source of high voltage; - an electrical supply battery. The device uses the method of gamma photons detection in energetic windows. Through theoretical and experimental studies carried out during the prototype development phase, the superiority of this method has been proved as compared with the installations which make use of the classical principle of photon integral detection. The achieved prototype has a basic program enabling the setting of all working parameters (measuring time, discriminating thresholds, discriminators operating conditions, etc.). Through the included interface RS232 it is possible to transmit the data to a more powerful computer in order to continually process the results. The spectrometric assembly, realized on the basis of micro-computers, can be used in a wide range of applications: measurement of thickness and erosion of walls and tubes, measurement of level in closed containers, of soil density, etc. The adjustment for specific application is performed only through a program modification. (authors)

  2. Plasma Pyrolysis Assembly Regeneration Evaluation

    Science.gov (United States)

    Medlen, Amber; Abney, Morgan B.; Miller, Lee A.

    2011-01-01

    In April 2010 the Carbon Dioxide Reduction Assembly (CRA) was delivered to the International Space Station (ISS). This technology requires hydrogen to recover oxygen from carbon dioxide. This results in the production of water and methane. Water is electrolyzed to provide oxygen to the crew. Methane is vented to space resulting in a loss of valuable hydrogen and unreduced carbon dioxide. This is not critical for ISS because of the water resupply from Earth. However, in order to have enough oxygen for long-term missions, it will be necessary to recover the hydrogen to maximize oxygen recovery. Thus, the Plasma Pyrolysis Assembly (PPA) was designed to recover hydrogen from methane. During operation, the PPA produces small amounts of carbon that can ultimately reduce performance by forming on the walls and windows of the reactor chamber. The carbon must be removed, although mechanical methods are highly inefficient, thus chemical methods are of greater interest. The purpose of this effort was to determine the feasibility of chemically removing the carbon from the walls and windows of a PPA reactor using a pure carbon dioxide stream.

  3. Nanoparticle Assemblies at Fluid Interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Thomas P. [Univ. of Massachusetts, Amherst, MA (United States). Dept. of Polymer Science and Engineering

    2015-03-10

    A systematic study of the structure and dynamics of nanoparticles (NP) and NP-surfactants was performed. The ligands attached to both the NPs and NP-surfactants dictate the manner in which the nanoscopic materials assemble at fluid interfaces. Studies have shown that a single layer of the nanoscpic materials form at the interface to reduce the interactions between the two immiscible fluids. The shape of the NP is, also, important, where for spherical particles, a disordered, liquid-like monolayer forms, and, for nanorods, ordered domains at the interface is found and, if the monolayers are compressed, the orientation of the nanorods with respect to the interface can change. By associating end-functionalized polymers to the NPs assembled at the interface, NP-surfactants are formed that increase the energetic gain in segregating each NP at the interface which allows the NP-surfactants to jam at the interface when compressed. This has opened the possibility of structuring the two liquids by freezing in shape changes of the liquids.

  4. 78 FR 34565 - Modification of Mandatory Label Information for Wine

    Science.gov (United States)

    2013-06-10

    ...The Alcohol and Tobacco Tax and Trade Bureau (TTB) is amending its regulations regarding the mandatory labeling requirements for wine. The regulatory change permits alcohol content to appear on other labels affixed to the container rather than requiring it to appear on the brand label. This regulatory change provides greater flexibility in wine labeling, and will conform the TTB wine labeling regulations to the agreement reached by members of the World Wine Trade Group regarding the presentation of certain information on wine labels.

  5. Educational Labeling System for Atmospheres (ELSA): Python Tool Development for Archiving Under the PDS4 Standard

    Science.gov (United States)

    Neakrase, Lynn; Hornung, Danae; Sweebe, Kathrine; Huber, Lyle; Chanover, Nancy J.; Stevenson, Zena; Berdis, Jodi; Johnson, Joni J.; Beebe, Reta F.

    2017-10-01

    The Research and Analysis programs within NASA’s Planetary Science Division now require archiving of resultant data with the Planetary Data System (PDS) or an equivalent archive. The PDS Atmospheres Node is developing an online environment for assisting data providers with this task. The Educational Labeling System for Atmospheres (ELSA) is being designed with Django/Python coding to provide an easier environment for facilitating not only communication with the PDS node, but also streamlining the process of learning, developing, submitting, and reviewing archive bundles under the new PDS4 archiving standard. Under the PDS4 standard, data are archived in bundles, collections, and basic products that form an organizational hierarchy of interconnected labels that describe the data and relationships between the data and its documentation. PDS4 labels are implemented using Extensible Markup Language (XML), which is an international standard for managing metadata. Potential data providers entering the ELSA environment can learn more about PDS4, plan and develop label templates, and build their archive bundles. ELSA provides an interface to tailor label templates aiding in the creation of required internal Logical Identifiers (URN - Uniform Resource Names) and Context References (missions, instruments, targets, facilities, etc.). The underlying structure of ELSA uses Django/Python code that make maintaining and updating the interface easy to do for our undergraduate/graduate students. The ELSA environment will soon provide an interface for using the tailored templates in a pipeline to produce entire collections of labeled products, essentially building the user’s archive bundle. Once the pieces of the archive bundle are assembled, ELSA provides options for queuing the completed bundle for peer review. The peer review process has also been streamlined for online access and tracking to help make the archiving process with PDS as transparent as possible. We discuss the

  6. Extending Modal Transition Systems with Structured Labels

    DEFF Research Database (Denmark)

    Bauer, Sebastian S.; Juhl, Line; Larsen, Kim Guldstrand

    2012-01-01

    We introduce a novel formalism of label-structured modal transition systems that combines the classical may/must modalities on transitions with structured labels that represent quantitative aspects of the model. On the one hand, the specification formalism is general enough to include models like...... weighted modal transition systems and allows the system developers to employ more complex label refinement than in the previously studied theories. On the other hand, the formalism maintains the desirable properties required by any specification theory supporting compositional reasoning. In particular, we...

  7. Valuing labelling attributes with hedonic price analysis:

    DEFF Research Database (Denmark)

    Steiner, Bodo

    2004-01-01

    employs hedonic price analysis to identify the values that marketers and consumers place on the information carried by the label of Australian wines in the British wine retail market. Although many grape varieties are given a highly distinct valuation by market participants, our results also suggest...... that consumers consider regions jointly with grape varieties as proxies for brands. This contrasts with the general observation that grape varietal labeling is the distinctive feature of New World wines. Marketing implications are examined by considering the revenue impact of changes in labeling at the retail...

  8. Labelling of immunoglobulins with metal radionuclides

    International Nuclear Information System (INIS)

    Budsky, F.; Prokop, J.; Hradil, M.

    1989-01-01

    The general principles are briefly described of labelling immunoglobulins with metal radionuclides. Bicyclic anhydrides cDTPAA and cEDTAA were selected for experiments by the Nuclear Research Institute at Rez near Prague. The compounds show sufficient reactivity to immunoglobulins and can be stored in an evacuated dessicator with calcium chloride at laboratory temperature for an unlimited time. The procedure is described of the preparation of the two anhydrides and of their labelling with 111 In and 99m Tc. For both radionuclides, favourable results have been obtained in labelling immunoglobulins, which creates preconditions for the introduction of immunoscintigraphy in Czechoslovak nuclear medicine. (Z.M.). 3 tabs., 13 refs

  9. Synthesis of plant hormones labelled by tritium

    International Nuclear Information System (INIS)

    Sidorov, G.V.; Myasoedov, N.F.

    1999-01-01

    Reaction of solid-phase catalytic hydrogenation, isotopic exchange with enriched tritium water, catalytic heterogenous isotopic exchange with gaseous tritium, hydrogenolysis as applied to synthesis of plants labelled by tritium were studied. Auxins, cytokinins, gibberellins, fusicoccins - representatives of the basic hormones of plants - were objects of investigations. In dependence on synthesis method compounds labelled by tritium were prepared with molar radioactivity from 5 up to 155 Ci/mmol. Order of universal approaches to synthesis of plant hormones labelled by tritium was formulated [ru

  10. The antibody approach of labeling blood cells

    Energy Technology Data Exchange (ETDEWEB)

    Srivastava, S.C.

    1991-12-31

    Although the science of blood cell labeling using monoclonal antibodies directed against specific cellular antigens is still in its early stages, considerable progress has recently been accomplished in this area. The monoclonal antibody approach offers the promise of greater selectivity and enhanced convenience since specific cell types can be labeled in vivo, thus eliminating the need for complex and damaging cell separation procedures. This article focuses on these developments with primary emphasis on antibody labeling of platelets and leukocytes. The advantages and the shortcomings of the recently reported techniques are criticality assessed and evaluated.

  11. The antibody approach of labeling blood cells

    Energy Technology Data Exchange (ETDEWEB)

    Srivastava, S.C.

    1991-01-01

    Although the science of blood cell labeling using monoclonal antibodies directed against specific cellular antigens is still in its early stages, considerable progress has recently been accomplished in this area. The monoclonal antibody approach offers the promise of greater selectivity and enhanced convenience since specific cell types can be labeled in vivo, thus eliminating the need for complex and damaging cell separation procedures. This article focuses on these developments with primary emphasis on antibody labeling of platelets and leukocytes. The advantages and the shortcomings of the recently reported techniques are criticality assessed and evaluated.

  12. The antibody approach of labeling blood cells

    Energy Technology Data Exchange (ETDEWEB)

    Srivastava, S.C.

    1992-12-31

    Although the science of blood cell labeling using monoclonal antibodies directed against specific cellular antigens is still in its early stages, considerable progress has recently been accomplished in this area. The monoclonal antibody approach offers the promise of greater selectivity and enhanced convenience since specific cell types can be labeled in vivo, thus eliminating the need for complex and damaging cell separation procedures. This article focuses on these developments with primary emphasis on antibody labeling of platelets and leukocytes. The advantages and the shortcomings of the recently reported techniques are critically assessed and evaluated.

  13. Synthesis of deuterium-labeled fluphenazine.

    Science.gov (United States)

    Shetty, H U; Hawes, E M; Midha, K K

    1984-01-01

    The propylpiperazine side chain of fluphenazine has been labeled with two, four, and six deuterium atoms by lithium aluminum deuteride reduction of the appropriate ester or imide. The gamma-carbon of the propyl group was labeled with two deuterium atoms by reduction of 10- (2-methoxycarbonylethyl) -2-trifluoromethyl-10H-phenothiazine, while four deuterium atoms were incorporated into the piperazine ring by reduction of 10-[3-(3,5-dioxo-1-piperazinyl)propyl]-2-trifluoromethyl-10H-pheno thiazine. The latter reduction gave the d4-labeled N-deshydroxyethyl metabolite of fluphenazine.

  14. Labelling of castor oil for myocardial study

    International Nuclear Information System (INIS)

    Hallaba, E.; Al-Suhybani, A.; Zaki, F.S.; Abdullah, M.E.

    1985-01-01

    The labelling of castor oil, hydrolyzed castor oil and oleic acid by iodine monochloride and chloramine-T was investigated. The effect of iodinating agent and concentration of castor oil on labelling yield was studied. A comparative pharmacological study with analog aliphatic acids was carried out. Castor oil labelled with iodine monochloride concentrates in heart and liver in good proportion, better than other natural fatty acids and nearly equal to analog fatty acids. Infrared study revealed that the OH group in ricinoleic acid may protect the sup(125)I added across the double bond with minor changes in biochemical properties causing better extraction by muscle of the heart. (author)

  15. Reductive methods for isotopic labeling of antibiotics

    International Nuclear Information System (INIS)

    Champney, W.S.

    1989-01-01

    Methods for the reductive methylation of the amino groups of eight different antibiotics using 3 HCOH or H 14 COH are presented. The reductive labeling of an additional seven antibiotics by NaB 3 H 4 is also described. The specific activity of the methyl-labeled drugs was determined by a phosphocellulose paper binding assay. Two quantitative assays for these compounds based on the reactivity of the antibiotic amino groups with fluorescamine and of the aldehyde and ketone groups with 2,4-dinitrophenylhydrazine are also presented. Data on the cellular uptake and ribosome binding of these labeled compounds are also presented

  16. The antibody approach of labeling blood cells

    International Nuclear Information System (INIS)

    Srivastava, S.C.

    1991-01-01

    Although the science of blood cell labeling using monoclonal antibodies directed against specific cellular antigens is still in its early stages, considerable progress has recently been accomplished in this area. The monoclonal antibody approach offers the promise of greater selectivity and enhanced convenience since specific cell types can be labeled in vivo, thus eliminating the need for complex and damaging cell separation procedures. This article focuses on these developments with primary emphasis on antibody labeling of platelets and leukocytes. The advantages and the shortcomings of the recently reported techniques are criticality assessed and evaluated

  17. The antibody approach of labeling blood cells

    International Nuclear Information System (INIS)

    Srivastava, S.C.

    1992-01-01

    Although the science of blood cell labeling using monoclonal antibodies directed against specific cellular antigens is still in its early stages, considerable progress has recently been accomplished in this area. The monoclonal antibody approach offers the promise of greater selectivity and enhanced convenience since specific cell types can be labeled in vivo, thus eliminating the need for complex and damaging cell separation procedures. This article focuses on these developments with primary emphasis on antibody labeling of platelets and leukocytes. The advantages and the shortcomings of the recently reported techniques are critically assessed and evaluated

  18. Static Electricity-Responsive Supramolecular Assembly.

    Science.gov (United States)

    Jintoku, Hirokuni; Ihara, Hirotaka; Matsuzawa, Yoko; Kihara, Hideyuki

    2017-12-01

    Stimuli-responsive materials can convert between molecular scale and macroscopic scale phenomena. Two macroscopic static electricity-responsive phenomena based on nanoscale supramolecular assemblies of a zinc porphyrin derivative are presented. One example involves the movement of supramolecular assemblies in response to static electricity. The assembly of a pyridine (Py) complex of the above-mentioned derivative in cyclohexane is drawn to a positively charged material, whereas the assembly of a 3,5-dimethylpyridine complex is drawn to a negatively charged material. The second phenomenon involves the movement of a non-polar solvent in response to static electrical stimulation. A cyclohexane solution containing a small quantity of the Py-complexed assembly exhibited a strong movement response towards negatively charged materials. Based on spectroscopic measurements and electron microscope observations, it was revealed that the assembled formation generates the observed response to static electricity. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. The MARVEL assembly for neutron multiplication

    Energy Technology Data Exchange (ETDEWEB)

    David L. Chichester; Mathew T. Kinlaw

    2013-10-01

    A new multiplying test assembly is under development at Idaho National Laboratory to support research, validation, evaluation, and learning. The item is comprised of three stacked, highly-enriched uranium (HEU) cylinders, each 11.4 cm in diameter and having a combined height of up to 11.7 cm. The combined mass of all three cylinders is 20.3 kg of HEU. Calculations for the bare configuration of the assembly indicate a multiplication level of >3.5 (keff=0.72). Reflected configurations of the assembly, using either polyethylene or tungsten, are possible and have the capability of raising the assembly's multiplication level to greater than 10. This paper describes simulations performed to assess the assembly's multiplication level under different conditions and describes the resources available at INL to support the use of these materials. We also describe some preliminary calculations and test activities using the assembly to study neutron multiplication.

  20. Chemical reactions directed Peptide self-assembly.

    Science.gov (United States)

    Rasale, Dnyaneshwar B; Das, Apurba K

    2015-05-13

    Fabrication of self-assembled nanostructures is one of the important aspects in nanoscience and nanotechnology. The study of self-assembled soft materials remains an area of interest due to their potential applications in biomedicine. The versatile properties of soft materials can be tuned using a bottom up approach of small molecules. Peptide based self-assembly has significant impact in biology because of its unique features such as biocompatibility, straight peptide chain and the presence of different side chain functionality. These unique features explore peptides in various self-assembly process. In this review, we briefly introduce chemical reaction-mediated peptide self-assembly. Herein, we have emphasised enzymes, native chemical ligation and photochemical reactions in the exploration of peptide self-assembly.

  1. Dynamic Multi-Component Hemiaminal Assembly

    Science.gov (United States)

    You, Lei; Long, S. Reid; Lynch, Vincent M.

    2012-01-01

    A simple approach to generating in situ metal templated tris-(2-picolyl)amine-like multi-component assemblies with potential applications in molecular recognition and sensing is reported. The assembly is based on the reversible covalent association between di-(2-picolyl)amine and aldehydes. Zinc ion is the best for inducing assembly among the metal salts investigated, while 2-picolinaldehyde is the best among the heterocyclic aldehydes studied. Although an equilibrium constant of 6.6 * 103 M-1 was measured for the assembly formed by 2-picolinaldehdye, di-(2-picolyl)amine, and zinc triflate, the equilibrium constants for other systems are in the 102 M-1 range. X-ray structural analysis revealed that zinc adopts a trigonal bipyramidal geometry within the assembled ligand. The diversity and equilibrium of the assemblies are readily altered by simply changing concentrations, varying components, or adding counter anions. PMID:21919095

  2. Chemical Reactions Directed Peptide Self-Assembly

    Directory of Open Access Journals (Sweden)

    Dnyaneshwar B. Rasale

    2015-05-01

    Full Text Available Fabrication of self-assembled nanostructures is one of the important aspects in nanoscience and nanotechnology. The study of self-assembled soft materials remains an area of interest due to their potential applications in biomedicine. The versatile properties of soft materials can be tuned using a bottom up approach of small molecules. Peptide based self-assembly has significant impact in biology because of its unique features such as biocompatibility, straight peptide chain and the presence of different side chain functionality. These unique features explore peptides in various self-assembly process. In this review, we briefly introduce chemical reaction-mediated peptide self-assembly. Herein, we have emphasised enzymes, native chemical ligation and photochemical reactions in the exploration of peptide self-assembly.

  3. Sandwich immunoassay for the prostate specific antigen using a micro-fluxgate and magnetic bead labels

    International Nuclear Information System (INIS)

    Sun, Xue-cheng; Lei, Chong; Guo, Lei; Zhou, Yong

    2016-01-01

    We describe a micro fluxgate based device with rectangular magnetic core for the determination of prostate specific antigen (PSA) labeled with Dynabeads. A sandwich immunoassay was employed where PSA is captured on a gold film modified with a self-assembled monolayer of antibody. The secondary antibody is labeled with Dynabeads. By applying a DC magnetic fields in the range of 460 to 700 μT, PSA can be detected with detection limit as low as 0.1 ng mL −1 . This micro fluxgate-based assay offers the advantages of miniaturization, simple and conveniently manipulation, re-usability and stability. In our perception, it offers a viable approach towards clinical determination of PSA or other biomarkers. (author)

  4. Probing molecular interactions with methylene blue derivatized self-assembled monolayers

    Directory of Open Access Journals (Sweden)

    Eleni Koutsoumpeli

    2015-12-01

    Full Text Available The emergence of stratified and personalised medicine and the associated need for highly multiplexed detection strategies are driving the development of innovative sensor technology. Electronic immunosensor arrays capable of label-free and highly parallel monitoring of ligand binding have emerged as a particularly promising technology capable of meeting these new diagnostic challenges. In this study, we present an approach for interrogating molecular interactions electronically using redox active molecular monolayers. Specifically, we have synthesised self-assembled molecular monolayers assembled from long-chain alkanethiols (LCAT incorporating oligoethyleneglycol (OEG linkers that can be derivatized with a range of functional groups, including the redox active molecule methylene blue. Critically, we show that the electron transport properties of this redox-active monolayer are highly sensitive to the electrochemical environment, including the local concentration of protons and the electrostatic potential at the plane of electron transfer. Using a combination of cyclic voltammetry and QCM-D to study in detail the behaviour of the monolayer during functionalisation and analyte binding, we demonstrate that these redox properties can be exploited for the electrochemical sensing of molecular interactions (biotin–avidin in our case on SAMs. Given the versatility of LCAT-OEG monolayers, in terms of linker lengths, choice of functional group, and ability to create mixed component layers and the straight-forward assembly of mixed SAMs of high quality, our electrochemical sensing approach forms an excellent and generic label-free platform for probing a wide range of molecular interactions.

  5. Fuel assembly for a nuclear reactor

    International Nuclear Information System (INIS)

    Gjertsen, R.K.; Tower, S.N.; Huckestein, E.A.

    1982-01-01

    A fuel assembly for a nuclear reactor comprises a 5x5 array of guide tubes in a generally 20x20 array of fuel elements, the guide tubes being arranged to accommodate either control rods or water displacer rods. The fuel assembly has top and bottom Inconel (Registered Trade Mark) grids and intermediate Zircaloy grids in engagement with the guide tubes and supporting the fuel elements and guide tubes while allowing flow of reactor coolant through the assembly. (author)

  6. Optics assembly for high power laser tools

    Science.gov (United States)

    Fraze, Jason D.; Faircloth, Brian O.; Zediker, Mark S.

    2016-06-07

    There is provided a high power laser rotational optical assembly for use with, or in high power laser tools for performing high power laser operations. In particular, the optical assembly finds applications in performing high power laser operations on, and in, remote and difficult to access locations. The optical assembly has rotational seals and bearing configurations to avoid contamination of the laser beam path and optics.

  7. Labeling has caused "incredible confusion".

    Science.gov (United States)

    1995-04-01

    The US Food and Drug Administration is considering changing the package labeling for the mini-pill to eliminate confusion about when to prescribe it. However, differing opinions about some related issues are hard to reconcile, to wit: whether breast feeding women should use progestin-only pills (POPs) or combined oral contraceptives (COCs). Less than 1% of American pill users rely on POPs, therefore manufacturers did not think it worthwhile to produce a separate insert for them. However, the shared insert has caused confusion. First-year failure rates for POPs range from 1.1% to 13.2%, but for lactating women they are nearly 100% effective if taken 3 weeks after delivery every day as a backup method. The consensus seems to be that POPs are used during lactation, and that at weaning or when menstruation returns women should switch to COCs. This should be done even if women were doing fine on POPs during breastfeeding, because POPs are less effective, cause irregular bleeding, and are implicated in a higher rate of ectopic pregnancies. In contrast to this opinion, another view is that prescribing COCs to breastfeeding women is acceptable, although lower-dose cyclic pills are preferred. Either pill would be acceptable for breastfeeding women according to a committee chair of the American Association of Pediatricians. Another option is to let the women decide themselves, especially if they have high blood pressure and do not like implants and injectables. For clients who choose POPs providers should assume that they comply with pill use; they should get feedback from them about the effectiveness of the pills; and they should allow them to have time to make a decision that would serve them in the long run.

  8. Kinetics of filamentous phage assembly

    Science.gov (United States)

    Ploss, Martin; Kuhn, Andreas

    2010-12-01

    Filamentous phages release their progeny particles by a secretory process without lysing the bacterial cell. By this process about 6 viral particles per min are secreted from each cell. We show here that when the major coat protein (gp8) is provided from a plasmid we observe a phage progeny production rate depending on the induction of gp8 by IPTG. We also show that a transfection of Escherichia coli lacking F-pili is observed using a mutant of M13 that carries an ampicillin resistance gene, and phage particles are secreted in the absence of an F-plasmid. Extruding phage was visualized by atomic force microscopy (AFM) and by transmission electron microscopy (TEM) using gold-labeled antibodies to the major coat protein.

  9. Fuel assembly for a nuclear reactor

    International Nuclear Information System (INIS)

    Gjertsen, R.K.

    1982-01-01

    A fuel assembly in a nuclear reactor comprises a locking mechanism that is capable of locking the fuel assembly to the core plate of a nuclear reactor to prevent inadvertent movement of the fuel assembly. The locking mechanism comprises a ratchet mechanism 108 that allows the fuel assembly to be easily locked to the core plate but prevents unlocking except when the ratchet is disengaged. The ratchet mechanism is coupled to the locking mechanism by a rotatable guide tube for a control rod or water displacer rod. (author)

  10. Automating System Assembly of Aerospace Systems

    Science.gov (United States)

    Manolios, Panagiotis

    2008-01-01

    One of the major challenges in modern aerospace designs is the integration and assembly of independently developed components. We have formalized this as the system assembly problem: from a sea of available components, which should be selected and how should they be connected, integrated, and assembled so that the overall system requirements are satisfied in a certifiable way? We present a powerful framework for automatically solving the system assembly problem directly from system requirements by using formal verification technology. We also present a case study where we applied our work to large-scale industrial examples from the Boeing Dreamliner.

  11. Peptide-Assembled Optically Responsive Nanoparticle Complexes

    National Research Council Canada - National Science Library

    Slocik, Joseph M; Tam, Felicia; Halas, Naomi J; Naik, Rajesh R

    2007-01-01

    .... Here we report two types of active nanoparticle complexes, with properties controlled by near-infrared illumination, resulting from the assembly of photothermally responsive plasmonic nanoparticle...

  12. Self-assembled nanomaterials for photoacoustic imaging.

    Science.gov (United States)

    Wang, Lei; Yang, Pei-Pei; Zhao, Xiao-Xiao; Wang, Hao

    2016-02-07

    In recent years, extensive endeavors have been paid to construct functional self-assembled nanomaterials for various applications such as catalysis, separation, energy and biomedicines. To date, different strategies have been developed for preparing nanomaterials with diversified structures and functionalities via fine tuning of self-assembled building blocks. In terms of biomedical applications, bioimaging technologies are urgently calling for high-efficient probes/contrast agents for high-performance bioimaging. Photoacoustic (PA) imaging is an emerging whole-body imaging modality offering high spatial resolution, deep penetration and high contrast in vivo. The self-assembled nanomaterials show high stability in vivo, specific tolerance to sterilization and prolonged half-life stability and desirable targeting properties, which is a kind of promising PA contrast agents for biomedical imaging. Herein, we focus on summarizing recent advances in smart self-assembled nanomaterials with NIR absorption as PA contrast agents for biomedical imaging. According to the preparation strategy of the contrast agents, the self-assembled nanomaterials are categorized into two groups, i.e., the ex situ and in situ self-assembled nanomaterials. The driving forces, assembly modes and regulation of PA properties of self-assembled nanomaterials and their applications for long-term imaging, enzyme activity detection and aggregation-induced retention (AIR) effect for diagnosis and therapy are emphasized. Finally, we conclude with an outlook towards future developments of self-assembled nanomaterials for PA imaging.

  13. Stochastic modeling of virus capsid assembly pathways

    Science.gov (United States)

    Schwartz, Russell

    2009-03-01

    Virus capsids have become a key model system for understanding self-assembly due to their high complexity, robust and efficient assembly processes, and experimental tractability. Our ability to directly examine and manipulate capsid assembly kinetics in detail nonetheless remains limited, creating a need for computer models that can infer experimentally inaccessible features of the assembly process and explore the effects of hypothetical manipulations on assembly trajectories. We have developed novel algorithms for stochastic simulation of capsid assembly [1,2] that allow us to model capsid assembly over broad parameter spaces [3]. We apply these methods to study the nature of assembly pathway control in virus capsids as well as their sensitivity to assembly conditions and possible experimental interventions. [4pt] [1] F. Jamalyaria, R. Rohlfs, and R. Schwartz. J Comp Phys 204, 100 (2005). [0pt] [2] N. Misra and R. Schwartz. J Chem Phys 129, in press (2008). [0pt] [3] B. Sweeney, T. Zhang, and R. Schwartz. Biophys J 94, 772 (2008).

  14. QUAST: quality assessment tool for genome assemblies.

    Science.gov (United States)

    Gurevich, Alexey; Saveliev, Vladislav; Vyahhi, Nikolay; Tesler, Glenn

    2013-04-15

    Limitations of genome sequencing techniques have led to dozens of assembly algorithms, none of which is perfect. A number of methods for comparing assemblers have been developed, but none is yet a recognized benchmark. Further, most existing methods for comparing assemblies are only applicable to new assemblies of finished genomes; the problem of evaluating assemblies of previously unsequenced species has not been adequately considered. Here, we present QUAST-a quality assessment tool for evaluating and comparing genome assemblies. This tool improves on leading assembly comparison software with new ideas and quality metrics. QUAST can evaluate assemblies both with a reference genome, as well as without a reference. QUAST produces many reports, summary tables and plots to help scientists in their research and in their publications. In this study, we used QUAST to compare several genome assemblers on three datasets. QUAST tables and plots for all of them are available in the Supplementary Material, and interactive versions of these reports are on the QUAST website. http://bioinf.spbau.ru/quast . Supplementary data are available at Bioinformatics online.

  15. Snubber assembly for a control rod drive

    International Nuclear Information System (INIS)

    Matthews, J.C.

    1978-01-01

    A snubber cartridge assembly is mounted to the nozzle of a control rod drive mechanism to insure that the snubber assembly will be located within the liquid filled section of a nuclear reactor vessel whenever the control rod drive is assembled thereto. The snubber assembly includes a piston mounted proximate to the control rod connecting end of the control rod drive leadscrew to allow the piston to travel within the liquid filled snubber cartridge and controllably exhaust liquid therefrom during a ''scram'' condition. The snubber cartridge provides three separate areas of increasing resistance to piston travel to insure a speedy but safe ''scram'' of the control rod into the reactor

  16. CASFISH: CRISPR/Cas9-mediated in situ labeling of genomic loci in fixed cells.

    Science.gov (United States)

    Deng, Wulan; Shi, Xinghua; Tjian, Robert; Lionnet, Timothée; Singer, Robert H

    2015-09-22

    Direct visualization of genomic loci in the 3D nucleus is important for understanding the spatial organization of the genome and its association with gene expression. Various DNA FISH methods have been developed in the past decades, all involving denaturing dsDNA and hybridizing fluorescent nucleic acid probes. Here we report a novel approach that uses in vitro constituted nuclease-deficient clustered regularly interspaced short palindromic repeats (CRISPR)/CRISPR-associated caspase 9 (Cas9) complexes as probes to label sequence-specific genomic loci fluorescently without global DNA denaturation (Cas9-mediated fluorescence in situ hybridization, CASFISH). Using fluorescently labeled nuclease-deficient Cas9 (dCas9) protein assembled with various single-guide RNA (sgRNA), we demonstrated rapid and robust labeling of repetitive DNA elements in pericentromere, centromere, G-rich telomere, and coding gene loci. Assembling dCas9 with an array of sgRNAs tiling arbitrary target loci, we were able to visualize nonrepetitive genomic sequences. The dCas9/sgRNA binary complex is stable and binds its target DNA with high affinity, allowing sequential or simultaneous probing of multiple targets. CASFISH assays using differently colored dCas9/sgRNA complexes allow multicolor labeling of target loci in cells. In addition, the CASFISH assay is remarkably rapid under optimal conditions and is applicable for detection in primary tissue sections. This rapid, robust, less disruptive, and cost-effective technology adds a valuable tool for basic research and genetic diagnosis.

  17. Facile labeling of lipoglycans with quantum dots

    International Nuclear Information System (INIS)

    Morales Betanzos, Carlos; Gonzalez-Moa, Maria; Johnston, Stephen Albert; Svarovsky, Sergei A.

    2009-01-01

    Bacterial endotoxins or lipopolysaccharides (LPS) are among the most potent activators of the innate immune system, yet mechanisms of their action and in particular the role of glycans remain elusive. Efficient non-invasive labeling strategies are necessary for studying interactions of LPS glycans with biological systems. Here we report a new method for labeling LPS and other lipoglycans with luminescent quantum dots. The labeling is achieved by partitioning of hydrophobic quantum dots into the core of various LPS aggregates without disturbing the native LPS structure. The biofunctionality of the LPS-Qdot conjugates is demonstrated by the labeling of mouse monocytes. This simple method should find broad applicability in studies concerned with visualization of LPS biodistribution and identification of LPS binding agents.

  18. Synthesis of deuterium-labelled diclofenac sodium

    International Nuclear Information System (INIS)

    Leroy, D.; Richard, J.; Godbillon, J.

    1993-01-01

    Dicolofenac sodium labelled with deuterium in the phenylacetic ring was prepared from [ 2 H 5 ]-bromobenzene in a six-step reaction. It was found to be suitable for use in pharmacokinetic and bioavailability studies in man. (Author)

  19. Read the Label First: Protect Your Pets

    Science.gov (United States)

    Learn about the importance of reading pet products labels before purchasing and using any product to insure the safety of your pets. Find tips for ways to reduce the changes of pets accessing potentially dangerous products.

  20. How to Read a Nutrition Facts Label

    Medline Plus

    Full Text Available ... Development Infections Diseases & Conditions Pregnancy & Baby Nutrition & Fitness Emotions & Behavior School & Family Life First Aid & Safety Doctors & ... I Look for When Reading Food Labels? Healthy Eating Kids and Food: 10 Tips for Parents Figuring ...